WorldWideScience

Sample records for anaerobic fluidized bed

  1. Experimental and theoretical investigation of anaerobic fluidized bed biofilm reactors

    Directory of Open Access Journals (Sweden)

    M. Fuentes

    2009-09-01

    Full Text Available This work presents an experimental and theoretical investigation of anaerobic fluidized bed reactors (AFBRs. The bioreactors are modeled as dynamic three-phase systems. Biochemical transformations are assumed to occur only in the fluidized bed zone. The biofilm process model is coupled to the system hydrodynamic model through the biofilm detachment rate; which is assumed to be a first-order function of the energy dissipation parameter and a second order function of biofilm thickness. Non-active biomass is considered to be particulate material subject to hydrolysis. The model includes the anaerobic conversion for complex substrate degradation and kinetic parameters selected from the literature. The experimental set-up consisted of two mesophilic (36±1ºC lab-scale AFBRs (R1 and R2 loaded with sand as inert support for biofilm development. The reactor start-up policy was based on gradual increments in the organic loading rate (OLR, over a four month period. Step-type disturbances were applied on the inlet (glucose and acetic acid substrate concentration (chemical oxygen demand (COD from 0.85 to 2.66 g L-1 and on the feed flow rate (from 3.2 up to 6.0 L d-1 considering the maximum efficiency as the reactor loading rate switching. The predicted and measured responses of the total and soluble COD, volatile fatty acid (VFA concentrations, biogas production rate and pH were investigated. Regarding hydrodynamic and fluidization aspects, variations of the bed expansion due to disturbances in the inlet flow rate and the biofilm growth were measured. As rate coefficients for the biofilm detachment model, empirical values of 3.73⋅10(4 and 0.75⋅10(4 s² kg-1 m-1 for R1 and R2, respectively, were estimated.

  2. Molecular analysis of the biomass of a fluidized bed reactor treating synthetic vinasse at anaerobic and micro-aerobic conditions

    NARCIS (Netherlands)

    Rodriguez, E.; Lopes, A.; Fdz-Polanco, M.; Stams, A.J.M.; Garcia Encina, P.A.

    2012-01-01

    The microbial communities (Bacteria and Archaea) established in an anaerobic fluidized bed reactor used to treat synthetic vinasse (betaine, glucose, acetate, propionate, and butyrate) were characterized by denaturing gradient gel electrophoresis (DGGE) and phylogenetic analysis. This study was focu

  3. Mechanisms of granular activated carbon anaerobic fluidized-bed process for treating phenols wastewater

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Granular activated carbon (GAC) anaerobic fluidized-bed reactor was applied to treating phenols wastewater. When influent phenol concentration was 1000 mg/L, volume loadings of phenol and CODCr were 0.39 kg/(m3*d) and 0.98 kg/(m3*d), their removal rates were 99.9% and 96.4% respectively. From analyzing above results, the main mechanisms of the process are that through fluidizing GAC, its adsorption is combined with biodegradation, both activities are brought into full play, and phenol in wastewater is effectively decomposed. Meanwhile problems concerning gas-liquid separation and medium plugging are well solved.

  4. A novel fast mass transfer anaerobic inner loop fluidized bed biofilm reactor for PTA wastewater treatment.

    Science.gov (United States)

    Chen, Yingwen; Zhao, Jinlong; Li, Kai; Xie, Shitao

    2016-01-01

    In this paper, a fast mass transfer anaerobic inner loop fluidized bed biofilm reactor (ILFBBR) was developed to improve purified terephthalic acid (PTA) wastewater treatment. The emphasis of this study was on the start-up mode of the anaerobic ILFBBR, the hydraulic loadings and the operation stability. The biological morphology of the anaerobic biofilm in the reactors was also analyzed. The anaerobic column could operate successfully for 46 days due to the pre-aerating process. The anaerobic column had the capacity to resist shock loadings and maintained a high stable chemical oxygen demand (COD) and terephthalic acid removal rates at a hydraulic retention time of 5-10 h, even under conditions of organic volumetric loadings as high as 28.8 kg COD·m(-3).d(-1). The scanning electron microscope analysis of the anaerobic carrier demonstrated that clusters of prokaryotes grew inside of pores and that the filaments generated by pre-aeration contributed to the anaerobic biofilm formation and stability. PMID:27642828

  5. COMPARISON OF PHENOL REMOVAL IN ANAEROBIC FLUIDIZED BED REACTORS WITH SAND AND GAC MEDIA

    Directory of Open Access Journals (Sweden)

    A.R. Yazdanbakhsh; A.R. Mesdaghinia; A. Torabian; M. Shariat

    1997-08-01

    Full Text Available In this study two identical anaerobic completely mixed fluidized bed reactors with GAC and sand media were employed for COD & phenol removal. At loading rate of 1.6 g phenol L-1d-1, the efficiency of phenol removal in GAC & sand reactors were 97.7% & 74%, respectively. At high loading rate of phenol (6.09 g phenol I: 1d1 the efficiency of phenol removal in GAC reactor was better than 95%. In GAC reactor, the main mechanism for phenol removal at steady state condition was biological process; this was concluded through balance of gas production and COD removal. Better efficiency of GAC reactor comparing with sand reactor was because of resistance to fluctuations, higher surface for biomass growth and adsorption capacity of activated carbon.

  6. Evaluation of Anaerobic Fluidized Bed Reactor for treating Sugar mill effluent - a Case Study

    Directory of Open Access Journals (Sweden)

    R. Mathiyazhagan

    2014-07-01

    Full Text Available Anaerobic treatment processes are credible options for providing sustainable treatment to biodegradable waste streams. The Anaerobic Fluidized Bed Reactor (AFBR is an evolving process that requires waste specific design methodologies based on kinetics of the specific process. The research was precisely an experimental study on AFBR having23.56 litres of effective volume to evaluate its treatment performance and gas recovery in terms of Chemical Oxygen Demand (COD, Hydraulic Retention Time(HRTand Organic Loading Rate (OLR. The synthetic sugar influent COD was variedfrom 1500 to 4000 mg/lit. The OLR for the operating flow rates were ranged from 1.36 to 28.8 Kg COD/m3 .day for HRT varied from 3.2 to 24 hrs. The maximum COD removal efficiency is 90.06 at an operating OLR of 3.42 Kg COD/m3 .day. The maximum biogas yield was observed at 0.28 m 3 /kg COD removed.

  7. Anaerobic tapered fluidized bed reactor for starch wastewater treatment and modeling using multilayer perceptron neural network

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Anaerobic treatability of synthetic sago wastewater was investigated in a laboratory anaerobic tapered fluidized bed reactor (ATFBR) with a mesoporous granular activated carbon (GAC) as a support material. The experimental protocol was defined to examine the effect of the maximum organic loading rate (OLR), hydraulic retention time (HRT), the efficiency of the reactor and to report on its steady-state performance. The reactor was subjected to a steady-state operation over a range of OLR up to 85.44 kg COD/(m3·d). The COD removal efficiency was found to be 92% in the reactor while the biogas produced in the digester reached 25.38 m3/(m3·d) of the reactor. With the increase of OLR from 83.7 kg COD/(m3·d), the COD removal efficiency decreases. Also an artificial neural network (ANN) model using multilayer perceptron (MLP) has been developed for a system of two input variable and five output dependent variables. For the training of the input-output data, the experimental values obtained have been used. The output parameters predicted have been found to be much closer to the corresponding experimental ones and the model was validated for 30% of the untrained data. The mean square error (MSE) was found to be only 0.0146.

  8. Biohydrogen production from cassava wastewater in an anaerobic fluidized bed reactor

    Directory of Open Access Journals (Sweden)

    N. C. S. Amorim

    2014-09-01

    Full Text Available The effect of hydraulic retention time (HRT and organic loading rate (OLR on biological hydrogen production was assessed using an anaerobic fluidized bed reactor fed with cassava wastewater. The HRT of this reactor ranged from 8 to 1 h (28 to 161 kg COD/m³-d. The inoculum was obtained from a facultative pond sludge derived from swine wastewater treatment. The effluent pH was approximately 5.00, while the influent chemical oxygen demand (COD measured 4000 mg COD/L. The hydrogen yield production increased from 0.13 to 1.91 mol H2/mol glucose as the HRT decreased from 8 to 2 h. The hydrogen production rate significantly increased from 0.20 to 2.04 L/h/L when the HRT decreased from 8 to 1 h. The main soluble metabolites were ethanol (1.87-100%, acetic acid (0.00-84.80%, butyric acid (0.00-66.78% and propionic acid (0.00-50.14%. Overall, we conclude that the best hydrogen yield production was obtained at an HRT of 2 h.

  9. Fluidized bed calciner apparatus

    Science.gov (United States)

    Owen, Thomas J.; Klem, Jr., Michael J.; Cash, Robert J.

    1988-01-01

    An apparatus for remotely calcining a slurry or solution feed stream of toxic or hazardous material, such as ammonium diurante slurry or uranyl nitrate solution, is disclosed. The calcining apparatus includes a vertical substantially cylindrical inner shell disposed in a vertical substantially cylindrical outer shell, in which inner shell is disposed a fluidized bed comprising the feed stream material to be calcined and spherical beads to aid in heat transfer. Extending through the outer and inner shells is a feed nozzle for delivering feed material or a cleaning chemical to the beads. Disposed in and extending across the lower portion of the inner shell and upstream of the fluidized bed is a support member for supporting the fluidized bed, the support member having uniform slots for directing uniform gas flow to the fluidized bed from a fluidizing gas orifice disposed upstream of the support member. Disposed in the lower portion of the inner shell are a plurality of internal electric resistance heaters for heating the fluidized bed. Disposed circumferentially about the outside length of the inner shell are a plurality of external heaters for heating the inner shell thereby heating the fluidized bed. Further, connected to the internal and external heaters is a means for maintaining the fluidized bed temperature to within plus or minus approximately 25.degree. C. of a predetermined bed temperature. Disposed about the external heaters is the outer shell for providing radiative heat reflection back to the inner shell.

  10. Investigation of Anaerobic Fluidized Bed Reactor Aerobic Mov-ing Bed Bio Reactor (AFBR/MMBR System for Treatment of Currant Wastewater

    Directory of Open Access Journals (Sweden)

    Jalil Jafari

    2013-08-01

    Full Text Available Background: Anaerobic treatment methods are more suitable for the treatment of concentrated wastewater streams, offer lower operating costs, the production of usable biogas product. The aim of this study was to investigate the performance of an Anaerobic Fluidized Bed Reactor (AFBR-Aerobic Moving Bed Bio Reactor (MBBR in series arrangement to treat Currant wastewater.Methods: The bed materials of AFBR were cylindrical particles made of PVC with a diameter of 2-2.3 mm, particle density of 1250 kg/m3.The volume of all bed materials was 1.7 liter which expanded to 2.46 liters in fluidized situation. In MBBR, support media was composed of 1.5 liters Bee-Cell 2000 having porosity of 87% and specific surface area of 650m2/m3.Results: When system operated at 35 ºC, chemical oxygen demand (COD removal efficiencies were achieved to 98% and 81.6% for organic loading rates (OLR of 9.4 and 24.2 g COD/l.d, and hydraulic retention times (HRT of 48 and 18 h, in average COD concentration feeding of 18.4 g/l, respectively.Conclusion: The contribution of AFBR in total COD removal efficiency at an organic loading rate (OLR of 9.4 g COD/l.d was 95%, and gradually decreased to 76.5% in OLR of 24.2 g COD/l.d. Also with increasing in organic loading rate the contribution of aerobic reactor in removing COD gradually decreased. In this system, the anaerobic reactor played the most important role in the removal of COD, and the aerobic MBBR was actually needed to polish the anaerobic treated wastewate

  11. Fluidized bed incinerator development

    International Nuclear Information System (INIS)

    A fluidized bed incinerator is being developed for burning rad contaminated solid and liquid waste materials. In situ neutralization of acid gases by the bed material, catalytic afterburning, and gas filtration are used to produce a clean flue gas without the use of aqueous scrubbing

  12. Characteristics of high-sulfate wastewater treatment by two-phase anaerobic digestion process with Jet-loop anaerobic fluidized bed

    Institute of Scientific and Technical Information of China (English)

    WEI Chao-hai; WANG Wen-xiang; DENG Zhi-yi; WU Chao-fei

    2007-01-01

    A new anaerobic reactor,Jet-loop anaerobic fluidized bed(JLAFB),was designed for treating high-sulfate wastewater.The treatment characteristics,including the effect of influent COD/SO42- ratio and alkalinity and sulfide inhibition in reactors,were discussed for a JLAFB and a general anaerobic fluidized bed(AFB)reactor used as sulfate-reducing phase and methane-producing phase,respectively,in two-phase anaerobic digestion process.The formation of granules in the two reactors was also examined.The results indicated that COD and sulfate removal had different demand of influent COD/S042- ratios.When total COD removal Was up to 85%,the ratio was only required up to 1.2,whereas,total sulfate removal up to 95%required it exceeding 3.0.The alkalinity in the two reactors increased linearly with the growth of influent alkalinity.Moreover,the change of influent alkalinity had no significant effect on pH and volatile fatty acids(VFA)in the two reactors.Influent alkalinity kept at 400-500 mg/t,could meet the requirement of the treating process.The JLAFB reactor had great advantage in avoiding sulfide and free-H2S accumulation and toxicity inhibition on microorganisms.When sulfate loading rate was up to 8.1 kg/(m3·d),the sulfide and free-H2S concentrations in JLAFB reactor were 58.6 and 49.7 mg/L,respectively.Furthermore,the granules,with offwhite color,ellipse shape and diameters of 1.0-3.0 mm,could be developed in JLAFB reactor.In granules,different groups of bacteria were distributed in different layers,and some inorganic metal compounds such as Fe,Ca,Mg etc.were found.

  13. Decoloration of textile wastewater by means of a fluidized-bed loop reactor and immobilized anaerobic bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Georgiou, D. [Department of Environmental Engineering, Demokritos University of Thrace, 67100 Xanthi (Greece)]. E-mail: dgeorgio@env.duth.gr; Aivasidis, A. [Department of Environmental Engineering, Demokritos University of Thrace, 67100 Xanthi (Greece)

    2006-07-31

    Textile wastewater was treated by means of a fluidized-bed loop reactor and immobilized anaerobic bacteria. The main target of this treatment was decoloration of the wastewater and transformation of the non-biodegradable azo-reactive dyes to the degradable, under aerobic biological conditions, aromatic amines. Special porous beads (Siran'' (registered)) were utilized as the microbial carriers. Acetic acid solution, enriched with nutrients and trace elements, served both as a pH-regulator and as an external substrate for the growth of methanogenic bacteria. The above technique was firstly applied on synthetic wastewater (an aqueous solution of a mixture of different azo-reactive dyes). Hydraulic residence time was gradually decreased from 24 to 6 h over a period of 3 months. Full decoloration of the wastewater could be achieved even at such a low hydraulic residence time (6 h), while methane-rich biogas was also produced. The same technique was then applied on real textile wastewater with excellent results (full decoloration at a hydraulic residence time of 6 h). Furthermore, the effluent proved to be highly biodegradable by aerobic microbes (activated-sludge). Thus, the above-described anaerobic/aerobic biological technique seems to be a very attractive method for treating textile wastewater since it is cost-effective and environment-friendly.

  14. A Two-Stage Microbial Fuel Cell and Anaerobic Fluidized Bed Membrane Bioreactor (MFC-AFMBR) System for Effective Domestic Wastewater Treatment

    OpenAIRE

    Ren, Lijiao; Ahn, Yongtae; Logan, Bruce E.

    2014-01-01

    Microbial fuel cells (MFCs) are a promising technology for energy-efficient domestic wastewater treatment, but the effluent quality has typically not been sufficient for discharge without further treatment. A two-stage laboratory-scale combined treatment process, consisting of microbial fuel cells and an anaerobic fluidized bed membrane bioreactor (MFC-AFMBR), was examined here to produce high quality effluent with minimal energy demands. The combined system was operated continuously for 50 d...

  15. Combined anaerobic digestion and photocatalytic treatment of distillery effluent in fluidized bed reactors focusing on energy conservation.

    Science.gov (United States)

    Apollo, Seth; Aoyi, Ochieng

    2016-09-01

    Anaerobic digestion (AD) can remove substantial amount of organic load when applied in treating distillery effluent but it is ineffective in colour reduction. Conversely, photodegradation is effective in colour reduction but has high energy requirement. A study on the synergy of a combined AD and ultra violet (UV) photodegradation treatment of distillery effluent was carried out in fluidized bed reactors to evaluate pollution reduction and energy utilization efficiencies. The combined process improved colour removal from 41% to 85% compared to that of AD employed as a stand-alone process. An overall corresponding total organic carbon (TOC) reduction of 83% was achieved. The bioenergy production by the AD step was 14.2 kJ/g total organic carbon (TOC) biodegraded while UV lamp energy consumption was 0.9 kJ/mg TOC, corresponding to up to 100% colour removal. Electrical energy per order analysis for the photodegradation process showed that the bioenergy produced was 20% of that required by the UV lamp to photodegrade 1 m(3) of undiluted pre-AD treated effluent up to 75% colour reduction. It was concluded that a combined AD-UV system for treatment of distillery effluent is effective in organic load removal and can be operated at a reduced cost. PMID:26824301

  16. Modeling phosphorus removal and recovery from anaerobic digester supernatant through struvite crystallization in a fluidized bed reactor.

    Science.gov (United States)

    Rahaman, Md Saifur; Mavinic, Donald S; Meikleham, Alexandra; Ellis, Naoko

    2014-03-15

    The cost associated with the disposal of phosphate-rich sludge, the stringent regulations to limit phosphate discharge into aquatic environments, and resource shortages resulting from limited phosphorus rock reserves, have diverted attention to phosphorus recovery in the form of struvite (MAP: MgNH4PO4·6H2O) crystals, which can essentially be used as a slow release fertilizer. Fluidized-bed crystallization is one of the most efficient unit processes used in struvite crystallization from wastewater. In this study, a comprehensive mathematical model, incorporating solution thermodynamics, struvite precipitation kinetics and reactor hydrodynamics, was developed to illustrate phosphorus depletion through struvite crystal growth in a continuous, fluidized-bed crystallizer. A thermodynamic equilibrium model for struvite precipitation was linked to the fluidized-bed reactor model. While the equilibrium model provided information on supersaturation generation, the reactor model captured the dynamic behavior of the crystal growth processes, as well as the effect of the reactor hydrodynamics on the overall process performance. The model was then used for performance evaluation of the reactor, in terms of removal efficiencies of struvite constituent species (Mg, NH4 and PO4), and the average product crystal sizes. The model also determined the variation of species concentration of struvite within the crystal bed height. The species concentrations at two extreme ends (inlet and outlet) were used to evaluate the reactor performance. The model predictions provided a reasonably good fit with the experimental results for PO4-P, NH4-N and Mg removals. Predicated average crystal sizes also matched fairly well with the experimental observations. Therefore, this model can be used as a tool for performance evaluation and process optimization of struvite crystallization in a fluidized-bed reactor. PMID:24384559

  17. Biodegradation of Reactive blue 13 in a two-stage anaerobic/aerobic fluidized beds system with a Pseudomonas sp. isolate.

    Science.gov (United States)

    Lin, Jun; Zhang, Xingwang; Li, Zhongjian; Lei, Lecheng

    2010-01-01

    Pseudomonas sp. strain L1 capable of degrading the azo textile dye Reactive blue 13, was isolated from activated sludge in a sequencing batch reactor. A continuous two-stage anaerobic/aerobic biological fluidized bed system was used to decolorize and mineralize Reactive blue 13. The key factors affecting decolorization were investigated and the efficiency of degradation was also optimized. An overall color removal of 83.2% and COD removal of 90.7% was achieved at pH 7, a residence time of 70 h and a glucose concentration of 2 g/L, HRT=70 h and C(glucose)=2000 mg/L. Oxygen was contributing to blocking the azo bond cleavage. Consequently, decolorization occurred in the anaerobic reactor while partial mineralization was achieved in the aerobic reactor. A possible degradation pathway based on the analysis of intermediates and involving azoreduction, desulfonation, deamination and further oxidation reactions is presented.

  18. Fluidization of potato starch in a stirred vibrating fluidized bed

    NARCIS (Netherlands)

    Kuipers, N.J M; Stamhuis, Eize; Beenackers, A.A C M

    1996-01-01

    A novel gas-solid reactor for cohesive C-powders such as potato starch is introduced, designed and characterized, the so-called stirred vibrating fluidized bed. The effects of a sinusoidal vibration of the gas distributor and/or stirring of the bed are investigated. The fluidization index, bed expan

  19. Fluidized bed desulfurization

    Science.gov (United States)

    Ravindram, M.; Kallvinskas, J. J. (Inventor)

    1985-01-01

    High sulfur content carbonaceous material, such as coal is desulfurized by continuous fluidized suspension in a reactor with chlorine gas, inert dechlorinating gas and hydrogen gas. A source of chlorine gas, a source of inert gas and a source of hydrogen gas are connected to the bottom inlet through a manifold and a heater. A flow controler operates servos in a manner to continuously and sequentially suspend coal in the three gases. The sulfur content is reduced at least 50% by the treatment.

  20. Fluidized Bed Reactor as Solid State Fermenter

    OpenAIRE

    Krishnaiah, K.; Janaun, J.; Prabhakar, A.

    2005-01-01

    Various reactors such as tray, packed bed, rotating drum can be used for solid-state fermentation. In this paper the possibility of fluidized bed reactor as solid-state fermenter is considered. The design parameters, which affect the performances are identified and discussed. This information, in general can be used in the design and the development of an efficient fluidized bed solid-state fermenter. However, the objective here is to develop fluidized bed solid-state fermenter for palm kerne...

  1. Performance evaluation and phylogenetic characterization of anaerobic fluidized bed reactors using ground tire and pet as support materials for biohydrogen production.

    Science.gov (United States)

    Barros, Aruana Rocha; Adorno, Maria Angela Tallarico; Sakamoto, Isabel Kimiko; Maintinguer, Sandra Imaculada; Varesche, Maria Bernadete Amâncio; Silva, Edson Luiz

    2011-02-01

    This study evaluated two different support materials (ground tire and polyethylene terephthalate [PET]) for biohydrogen production in an anaerobic fluidized bed reactor (AFBR) treating synthetic wastewater containing glucose (4000 mg L(-1)). The AFBR, which contained either ground tire (R1) or PET (R2) as support materials, were inoculated with thermally pretreated anaerobic sludge and operated at a temperature of 30°C. The AFBR were operated with a range of hydraulic retention times (HRT) between 1 and 8h. The reactor R1 operating with a HRT of 2h showed better performance than reactor R2, reaching a maximum hydrogen yield of 2.25 mol H(2)mol(-1) glucose with 1.3mg of biomass (as the total volatile solids) attached to each gram of ground tire. Subsequent 16S rRNA gene sequencing and phylogenetic analysis of particle samples revealed that reactor R1 favored the presence of hydrogen-producing bacteria such as Clostridium, Bacillus, and Enterobacter.

  2. Fluidization characteristics of rice husk in a bubbling fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Leon, M.A. [Dalhousie Univ., Halifax, NS (Canada). Dept. of Mechanical Engineering; Dutta, A. [Nova Scotia Agricultural College, Truro, NS (Canada). Biomass Conversion and Biofuels

    2010-02-15

    Rice husk is made of 75 per cent volatile matter and 25 per cent ash. The ash contains nearly 90 per cent high-grade amorphous silica that can be recovered if it is burnt or gasified at low temperature in a fluidized bed. Amorphous silica is in demand for high-performance cement with low permeability and superior strength. However, sand is often added to the fluidized bed to prevent slugging. The resulting husk-ash mixed with sand is a useless disposal burden that cannot be used in any applications. This study demonstrated how to fluidize rice husk in a wide bed without the presence of another granular solid such as sand. Experimental results from a circulating fluidized bed showed that bed cross-section has an important influence on the fluidization characteristics of rice husk. As the cross-section increases, it becomes easier to fluidize the husk without slugging. Particle size, sphericity, bulk density, and transport velocity of husk were measured in this study. The riser was operated under bubbling bed regimes. The minimum fluidization velocity was measured under different bed depths and cross-sections. The study confirmed that rice husk fluidized in a bed of sand can be kept in a pseudo fluidized state without mixing it with granular solid particles if the bed is large enough to avoid slug formation. The pseudo bubbling fluidized state is characterized by many micro-channels that constantly form and dissolve. The addition of smooth fine sand particles reduces the inter-particle friction, resulting in better bed fluidizing at lower gas velocity. 12 refs., 2 tabs., 5 figs.

  3. Flow Pattern Identification of Fluidized Beds Using ECT

    Institute of Scientific and Technical Information of China (English)

    S. Liu; W.Q. Yang; H. Wang; G. Yan; Z. Pan

    2001-01-01

    Electrical capacitance tomography (ECT) was applied in measuring solids distribution in square circulating fluidized beds. The fluidization conditions varied from bubbling fluidized bed to circulating fluidized bed. In the whole range of fluidization conditions, ECT was able to instantaneously provide the solids concentration and voids distributions in the fluidized beds. According to the acquired data from ECT and reconstructed image,different fluidization regimes can also be identified.

  4. Perspectives for Fluidized Bed Nuclear Reactor Technology using Rotating Fluidized Beds in a Static Geometry

    Science.gov (United States)

    Broqueville, Axel De; Wilde, Juray De

    The new concept of a rotating fluidized bed in a static geometry opens perspectives for fluidized bed nuclear reactor technology and is experimentally and numerically investigated. With conventional fluidized bed technology, the maximum attainable power is rather limited and maximum at a certain fluidization gas flow rate. Using a rotating fluidized bed in a static geometry, the fluidization gas drives both the centrifugal force and the counteracting radial gas-solid drag force in a similar way. This allows operating the reactor at any chosen sufficiently high solids loading over a much wider fluidization gas flow rate range and in particular at much higher fluidization gas flow rates than with conventional fluidized bed reactor technology, offering increased flexibility with respect to cooling via the fluidization gas. Furthermore, the centrifugal force can be a multiple of earth gravity, allowing radial gas-solid slip velocities much higher than in conventional fluidized beds. The latter result in gas-solid heat transfer coefficients one or multiple orders of magnitude higher than in conventional fluidized beds. The combination of dense operation and high fluidization gas flow rates allows process intensification and a more compact reactor design.

  5. Fluidized Bed Reactor as Solid State Fermenter

    Directory of Open Access Journals (Sweden)

    Krishnaiah, K.

    2005-01-01

    Full Text Available Various reactors such as tray, packed bed, rotating drum can be used for solid-state fermentation. In this paper the possibility of fluidized bed reactor as solid-state fermenter is considered. The design parameters, which affect the performances are identified and discussed. This information, in general can be used in the design and the development of an efficient fluidized bed solid-state fermenter. However, the objective here is to develop fluidized bed solid-state fermenter for palm kernel cake conversion into enriched animal and poultry feed.

  6. Heat and Mass Transfer Enforcement of Vibrating Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    ChuZhide; YangJunhong; 等

    1994-01-01

    This paper briefly introduces the development of vibrating fluidized bed at home and abroad,elaborates the vibration properties of vibrating fluidized bed.the fluidizing velocity and pressure drop of the bed layer,it also deduces the non-steady state drying dynamic equations of vibrating fluidized bed,analyzes main factors which influence the drying rate and inquires into drying rules of fixed bed and vibrating fluidized bed.

  7. Fluidized bed heat treating system

    Energy Technology Data Exchange (ETDEWEB)

    Ripley, Edward B; Pfennigwerth, Glenn L

    2014-05-06

    Systems for heat treating materials are presented. The systems typically involve a fluidized bed that contains granulated heat treating material. In some embodiments a fluid, such as an inert gas, is flowed through the granulated heat treating medium, which homogenizes the temperature of the heat treating medium. In some embodiments the fluid may be heated in a heating vessel and flowed into the process chamber where the fluid is then flowed through the granulated heat treating medium. In some embodiments the heat treating material may be liquid or granulated heat treating material and the heat treating material may be circulated through a heating vessel into a process chamber where the heat treating material contacts the material to be heat treated. Microwave energy may be used to provide the source of heat for heat treating systems.

  8. A two-stage microbial fuel cell and anaerobic fluidized bed membrane bioreactor (MFC-AFMBR) system for effective domestic wastewater treatment.

    KAUST Repository

    Ren, Lijiao

    2014-03-10

    Microbial fuel cells (MFCs) are a promising technology for energy-efficient domestic wastewater treatment, but the effluent quality has typically not been sufficient for discharge without further treatment. A two-stage laboratory-scale combined treatment process, consisting of microbial fuel cells and an anaerobic fluidized bed membrane bioreactor (MFC-AFMBR), was examined here to produce high quality effluent with minimal energy demands. The combined system was operated continuously for 50 days at room temperature (∼25 °C) with domestic wastewater having a total chemical oxygen demand (tCOD) of 210 ± 11 mg/L. At a combined hydraulic retention time (HRT) for both processes of 9 h, the effluent tCOD was reduced to 16 ± 3 mg/L (92.5% removal), and there was nearly complete removal of total suspended solids (TSS; from 45 ± 10 mg/L to <1 mg/L). The AFMBR was operated at a constant high permeate flux of 16 L/m(2)/h over 50 days, without the need or use of any membrane cleaning or backwashing. Total electrical energy required for the operation of the MFC-AFMBR system was 0.0186 kWh/m(3), which was slightly less than the electrical energy produced by the MFCs (0.0197 kWh/m(3)). The energy in the methane produced in the AFMBR was comparatively negligible (0.005 kWh/m(3)). These results show that a combined MFC-AFMBR system could be used to effectively treat domestic primary effluent at ambient temperatures, producing high effluent quality with low energy requirements.

  9. Circulating fluidized bed biological reactor for nutrients removal

    Institute of Scientific and Technical Information of China (English)

    Yubo CUI; Hongbo LIU; Chunxue BAI

    2008-01-01

    A new biological nitrogen removal process, which is named herein "The circulating fluidized bed bio-reactor (CFBBR)", was developed for simultaneous removal of nitrogen and organic matter. This process was composed of an anaerobic bed (Riser), aerobic bed (Downer) and connecting device. Influent and nitrified liquid from the aerobic bed enters the anaerobic bed from the bottom of the anaerobic bed, completing the removal of nitrogen and organic matter. The system performance under the conditions of different inflow loadings and nitrified liquid recirculation rates ranging from 200% to 600% was examined. From a technical and economic point of view, the optimum nitrified liquid recirculation rate was 400%. With a shortest total retention time of 2.5 h (0.8 h in the anaerobic bed and 1.5 h in the aerobic bed) and a nitrified liquid recir-culation rate of 400% based on the intluent flow rate, the average removal efficiencies of total nitrogen (TN) and sol-uble chemical oxygen demand (SCOD) were found to be 88% and 95%, respectively. The average effluent concentra-tions of TN and SCOD were 3.5 mg/L and 16 mg/L, respectively. The volatile suspended solid (VSS) concentra-tion, nitrification rate and denitrification rate in the system were less than 1.0 g/L, 0.026-0.1 g NH4+-N/g VSS.d, and 0.016-0.074 g NOx--N/g VSS.d, respectively.

  10. Wall-to-bed heat transfer in circulating fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Fox, W.B.; Grewal, N.S.; Moen, D.A. [Univ. of North Dakota, Grand Forks, ND (United States). Mechanical Engineering Dept.

    1999-05-01

    Circulating fluidized beds (CFBs) have become increasingly important in recent years for coal combustion and gas-solid reactions. Here, heat transfer from the wall of a circulating fluidized bed to the fast bed suspension has been investigated for several materials. The range of investigation includes dense and dilute phase fast fluidization and pneumatic transport. The overall heat transfer coefficient was found to be a function mainly of cross-sectional average suspension density. Effects of superficial velocity and solids mass flux were obscured by their interrelationship to the suspension density. Two models from the literature are evaluated using present and published data.

  11. Particle pressures in fluidized beds. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, C.S.; Rahman, K.; Jin, C.

    1996-09-01

    This project studies the particle pressure, which may be thought of as the force exerted by the particulate phase of a multiphase mixture, independently of that exerted by other phases. The project is divided into two parts, one concerning gas and the other liquid fluidized beds. Previous work on gas fluidized beds had suggested that the particle pressures are generated by bubbling action. Thus, for these gas fluidized bed studies, the particle pressure is measured around single bubbles generated in 2-D fluidized beds, using special probes developed especially for this purpose. Liquid beds are immune from bubbling and the particle pressures proved too small to measure directly. However, the major interest in particle pressures in liquid beds lies in their stabilizing effect that arises from the effective elasticity (the derivative of the particle pressure with respect to the void fraction), they impart to the bed. So rather than directly measure the particle pressure, the authors inferred the values of the elasticity from measurements of instability growth in liquid beds; the inference was made by first developing a generic stability model (one with all the normally modeled coefficients left undetermined) and then working backwards to determine the unknown coefficients, including the elasticity.

  12. Particle Pressures in Fluidized Beds. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, C.S.; Rahman, K.; Jin, C.

    1996-09-01

    This project studies the particle pressure, which may be thought of as the force exerted by the particulate phase of a multiphase mixture, independently of that exerted by other phases. The project is divided into two parts, one concerning gas and the other liquid fluidized beds. Previous work on gas fluidized beds had suggested that the particle pressures are generated by bubbling action. Thus, for these gas fluidized bed studies, the particle pressure is measured around single bubbles generated in 2-D fluidized beds, using special probes developed especially for this purpose. Liquid beds are immune from bubbling and the particle pressures proved too small to measure directly. However, the major interest in particle pressures in liquid beds lies in their stabilizing effect that arises from the effective elasticity (the derivative of the particle pressure with respect to the void fraction): they impart to the bed. So rather than directly measure the particle pressure, we inferred the values of the elasticity from measurements of instability growth in liquid beds the inference was made by first developing a generic stability model (one with all the normally modeled coefficients left undetermined)and then working backwards to determine the unknown coefficients, including the elasticity.

  13. Fluidization Characteristics of a Prototype Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    F. ABERUAGBA

    2005-01-01

    Full Text Available The fluidization characteristics of a prototype-fluidized bed laboratory reactor were understudied in order to investigate the suitable conditions at which the dehydrogenation reaction of butane could be carried out. To achieve this, a reactor with an effective volume of 1100ml was fabricated and coupled with temperature and pressure accessories.Zeolites were obtained from the market and clay obtained from different sources and pre-treated was used as catalyst. Airflow at high velocity between 3000-7000ml/hr was used as the fluidising medium to obtain the bed characteristics while butane gas was used to obtain the dehydrogenation kinetics.The temperature of the reactor system was varied between 353K and 413K while maintaining constant pressure of 1.5 105 N/m2 through a manifold gauge and a constant catalyst weight. Various methods such as pressure fluctuations, visual observations, and bed expansion were used to determine the transition velocity at which fluidization begins. It was observed that this depends on factors such as mean particle size, particle size distribution, and column diameter.The minimum fluidizing velocity obtained for zeolite was 0.0133m/s and 0.0102m/s for treated clay materials both for a particle size of 250μm. The conversion of butane over the catalysts showed an increase in both cases with a maximum at 0.9813 at 413K. This decreases as the reaction progresses.

  14. Fluidized-bed reactors processes and operating conditions

    CERN Document Server

    Yates, John G

    2016-01-01

    The fluidized-bed reactor is the centerpiece of industrial fluidization processes. This book focuses on the design and operation of fluidized beds in many different industrial processes, emphasizing the rationale for choosing fluidized beds for each particular process. The book starts with a brief history of fluidization from its inception in the 1940’s. The authors present both the fluid dynamics of gas-solid fluidized beds and the extensive experimental studies of operating systems and they set them in the context of operating processes that use fluid-bed reactors. Chemical engineering students and postdocs as well as practicing engineers will find great interest in this book.

  15. 21 CFR 890.5160 - Air-fluidized bed.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Air-fluidized bed. 890.5160 Section 890.5160 Food... DEVICES PHYSICAL MEDICINE DEVICES Physical Medicine Therapeutic Devices § 890.5160 Air-fluidized bed. (a) Identification. An air-fluidized bed is a device employing the circulation of filtered air through...

  16. Kinetic behavior of solid particles in fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Kono, H.O.

    1990-06-01

    The overall objectives of this project are to develop experimental techniques for measuring the forces of fluidized particles, and to predict the solid-gas performance in fluidized beds by using data analysis system, and by elucidating the intrinsic mechanism of erosion and attrition phenomena in fluidized beds. The reduction of erosion and attrition rates is one of the critical engineering problems for the design and operation of fluidized bed combustors. Specifically, the objectives are to: (1) develop the experimental techniques to measure the forces of solid particles prevailing in fluidized beds: (2) measure and characterize the forces of solid particles in various types of fluidized beds with various configurations (conventional and spouted fluidized beds) and with different scales (10, 20, and 30cm) under various fluidization conditions (particle size, bed aspect ratio and gas velocity); (3) find and verify the mechanism of erosion rates of in-bed tubes and attrition rates of fluidized particles by forces of solid particles in fluidized beds. We developed three different kinds of measurement methods, i.e., fracture sensitive sensor, piezoelectric sensor and gas pressure fluctuation method. By using these methods the exact forces of solid particles, including the transient corporate in fluidized beds, were systematically measured. Simultaneously, the erosion rates of in-bed tubes and attrition rates of fluidized particles were measured. 69 figs., 9 tabs.

  17. Control of fluidized bed tea drying

    NARCIS (Netherlands)

    Temple, S.J.

    2000-01-01

    Tea is a product made from the leaf of the tea bush by several processes, including drying. The drying stage is the most energy intensive, and has tight performance criteria. This project investigated the options for the control of a fluidized bed tea dryer. The work included establishing some of th

  18. Agglomeration in fluidized beds: detection and counteraction

    NARCIS (Netherlands)

    Bartels. M.

    2008-01-01

    Fluidized beds comprise a quantity of solid particles that is suspended by an upward flowing gas. They are used for a variety of processes in the chemical industry, such as catalytic reactions, drying, coating and energy conversion. A major problem in industrial practice is the occurrence of unwante

  19. Performance evaluation of an anaerobic fluidized bed reactor with natural zeolite as support material when treating high-strength distillery wastewater

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, N. [Renewable Energy Technology Center (CETER), ' ' Jose Antonio Echeverria' ' Polytechnical University, Calle 127 s/n, CP 19390, Apdo. 6028, Habana 6 Marianao, Ciudad de La Habana (Cuba); Montalvo, S. [Department of Chemical Engineering, Santiago de Chile University, Ave. Lib. Bernardo O' Higgins 3363, Santiago de Chile (Chile); Borja, R.; Travieso, L.; Raposo, F. [Instituto de la Grasa (CSIC), Avenida Padre Garcia Tejero 4, 41012 Sevilla (Spain); Guerrero, L. [Department of Chemical, Biotechnological and Environmental Processes, Federico Santa Maria Technical University, Casilla 110-V, Valparaiso (Chile); Sanchez, E.; Colmenarejo, M.F. [Centro de Ciencias Medioambientales (CSIC), C/Serrano, 115-Duplicado, 28006 Madrid (Spain); Cortes, I. [Environment Nacional Center, Chile University, Ave. Larrain 9975, La Reina, Santiago de Chile (Chile)

    2008-11-15

    The performance of two laboratory-scale fluidized bed reactors with natural zeolite as support material when treating high-strength distillery wastewater was assessed. Two sets of experiments were carried out. In the first experimental set, the influences of the organic loading rate (OLR), the fluidization level (FL) and the particle diameter of the natural zeolite (D{sub P}) were evaluated. This experimental set was carried out at an OLR from 2 to 5 g COD (chemical oxygen demand)/l d, at FL 20% and 40% and with D{sub P} in the range of 0.2-0.5 mm (reactor 1) and of 0.5-0.8 mm (reactor 2). It was demonstrated that OLR and FL had a slight influence on COD removal, whereas they had a strong influence on the methane production rate. The COD removal was slightly higher for the highest particle diameter used. The second experimental set was carried out at an OLR from 3 to 20 g COD/l d with 25% of fluidization and D{sub P} in the above-mentioned ranges for reactors 1 and 2. The performance of the two reactors was similar; no significant differences were found. The COD removal efficiency correlated with the OLR based on a straight line. COD removal efficiencies higher than 80% were achieved in both reactors without significant differences. In addition, a straight line equation with a slope of 1.74 d{sup -1} and an intercept on the y-axis equal to zero described satisfactorily the effect of the influent COD on the COD removal rate. It was also observed that both COD removal rate and methane production (Q{sub M}) increased linearly with the OLR, independently of the D{sub P} used. (author)

  20. Modelling of Devolatilization in Fluidized Bed Combustion

    DEFF Research Database (Denmark)

    Stenseng, Mette; Lin, Weigang; Johnsson, Jan Erik;

    1997-01-01

    A mathematical model is developed to describe the devolatilization process in a circulating fluidized bed combustor. The model is a combination of two submodels: single particle devolatilization and fluid dynamics. The single particle model includes the influence of both chemical kinetics and heat...... of CSTR's and the size and number of CSTR's has been estimated from tracer experiments in an 80 MWth CFB boiler. It was not possible to evaluate the model against experimental data, but the dependence of particle size on the degree of devolatilization in the dense bed agrees qualitative with the expected...... behavior. The model shows that the devolatilization mainly occurs in the dense bed....

  1. Experimental installation with pressurized fluidized bed boiler

    Energy Technology Data Exchange (ETDEWEB)

    Dobrzanski, W.; Szwarc, W.; Jurek, K.; Prokop, A. (Politechnika Warszawska (Poland). Instytut Techniki Cieplnej)

    1990-01-01

    Describes a test installation with a 3 MW pressurized fluidized bed boiler. The installation was commissioned at the Institute of Heat Engineering at the Technical University in Warsaw. Predesign assumptions and the lay-out of the installation are given. A schematic diagram of the pressurized (0.6 MPa) fluidized bed boiler with an inner diameter of 1.4 m and a total height of 5.45 m is shown. The fuel feeding system consists of a coal and adsorbent container, two feeders and an air jet pump for pneumatic transport. A water type boiler is integrated into the pressure vessel. Flue gas cyclones are also integrated into a separate pressure vessel. The computerized control system and instrumentation are described. Temperatures, pressures, pressure differences, rotational speeds and the chemical composition of gases are monitored.

  2. Drying in the rotating-pulsed fluidized bed

    OpenAIRE

    M. C. B. Ambrosio-Ugri; O.P. Taranto

    2007-01-01

    There are particulate materials that are cohesive when wet. Although they are Geldart's group A dry powders, they show difficulties in fluidizing in a conventional fluidized bed, which could be diminished by modifying the fluidization equipment. Therefore, the objective of this work was to study the drying of cohesive particulate material using a rotating-pulsed fluidized bed. The material used in the drying study was 2-hydroxybenzoic acid because its cohesive forces are stronger when wet. Th...

  3. Cluster Dynamics in a Circulating Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Guenther, C.P.; Breault, R.W.

    2006-11-01

    A common hydrodynamic feature in industrial scale circulating fluidized beds is the presence of clusters. The continuous formation and destruction of clusters strongly influences particle hold-up, pressure drop, heat transfer at the wall, and mixing. In this paper fiber optic data is analyzed using discrete wavelet analysis to characterize the dynamic behavior of clusters. Five radial positions at three different axial locations under five different operating were analyzed using discrete wavelets. Results are summarized with respect to cluster size and frequency.

  4. Circulating fluidized bed boilers design and operations

    CERN Document Server

    Basu, Prabir

    1991-01-01

    This book provides practicing engineers and students with insight into the design and operation of circulating fluidized bed (CFB) boilers. Through a combination of theoretical concepts and practical experience, this book gives the reader a basic understanding of the many aspects of this subject.Important environmental considerations, including solid waste disposal and predicted emissions, are addressed individually in separate chapters. This book places an emphasis on combustion, hydrodynamics, heat transfer, and material issues, and illustrates these concepts with numerous examples of pres

  5. Fluidized Bed Asbestos Sampler Design and Testing

    Energy Technology Data Exchange (ETDEWEB)

    Karen E. Wright; Barry H. O' Brien

    2007-12-01

    A large number of samples are required to characterize a site contaminated with asbestos from previous mine or other industrial operations. Current methods, such as EPA Region 10’s glovebox method, or the Berman Elutriator method are time consuming and costly primarily because the equipment is difficult to decontaminate between samples. EPA desires a shorter and less costly method for characterizing soil samples for asbestos. The objective of this was to design and test a qualitative asbestos sampler that operates as a fluidized bed. The proposed sampler employs a conical spouted bed to vigorously mix the soil and separate fine particulate including asbestos fibers on filters. The filters are then analyzed using transmission electron microscopy for presence of asbestos. During initial testing of a glass prototype using ASTM 20/30 sand and clay fines as asbestos surrogates, fine particulate adhered to the sides of the glass vessel and the tubing to the collection filter – presumably due to static charge on the fine particulate. This limited the fines recovery to ~5% of the amount added to the sand surrogate. A second prototype was constructed of stainless steel, which improved fines recovery to about 10%. Fines recovery was increased to 15% by either humidifying the inlet air or introducing a voltage probe in the air space above the sample. Since this was not a substantial improvement, testing using the steel prototype proceeded without using these techniques. Final testing of the second prototype using asbestos suggests that the fluidized bed is considerably more sensitive than the Berman elutriator method. Using a sand/tremolite mixture with 0.005% tremolite, the Berman elutriator did not segregate any asbestos structures while the fluidized bed segregated an average of 11.7. The fluidized bed was also able to segregate structures in samples containing asbestos at a 0.0001% concentration, while the Berman elutriator method did not detect any fibers at this

  6. Single-stage fluidized-bed gasification

    Science.gov (United States)

    Lau, F. S.; Rue, D. M.; Weil, S. A.; Punwani, D. V.

    1982-04-01

    The single-stage fluidized-bed gasification process, in addition to being a simple system, maximizes gas production and allows the economic exploitation of small peat deposits. The objective of this gasification project is to conduct experiments in order to obtain data for designing a single-stage fluidized-bed gasifier, and to evaluate the economics of converting peat to synthesis gas and to SNG by this process. An existing high-temperature and high-pressure process development unit (PDU) was modified to permit the direct feeding of peat to the fluidized bed. Peat flows by gravity from the feed hopper through a 6-inch line to the screw-feeder conveyor. From there, it is fed to the bottom tee section of the reactor and transported into the gasification zone. Oxygen and steam are fed through a distributing ring into the reactor. Gasification reactions occur in the annulus formed by the reactor tube and a central standpipe. Peat ash is discharged from the reactor by overflowing into the standpipe and is collected in a solids receiver.

  7. Status of the fluidized bed unit

    Energy Technology Data Exchange (ETDEWEB)

    Williams, P.M.; Wade, J.F.

    1994-06-01

    Rocky Flats has a serious mixed waste problem. No technology or company has a license and available facilities to remedy this dilemma. One solution under study is to use a catalytic fluidized bed unit to destroy the combustible portion of the mixed waste. The fluidized bed thermal treatment program at Rocky Flats is building on knowledge gained over twenty years of successful development activity. The FBU has numerous technical advantages over other thermal technologies to treat Rocky Flats` mixed waste, the largest being the lower temperature (700{degrees}C versus 1000{degrees}C) which reduces acid corrosion and mechanical failures and obviates the need for ceramic lining. Successful demonstrations have taken place on bench, pilot, and full-scale tests using radioactive mixed wastes. The program is approaching implementation and licensing of a production-scale fluidized bed system for the safe treatment of mixed waste. The measure for success on this project is the ability to work closely with the community to jointly solve problems and respond to concerns of mixed waste treatment at Rocky Flats.

  8. Modeling biomass gasification in circulating fluidized beds

    Science.gov (United States)

    Miao, Qi

    In this thesis, the modeling of biomass gasification in circulating fluidized beds was studied. The hydrodynamics of a circulating fluidized bed operating on biomass particles were first investigated, both experimentally and numerically. Then a comprehensive mathematical model was presented to predict the overall performance of a 1.2 MWe biomass gasification and power generation plant. A sensitivity analysis was conducted to test its response to several gasifier operating conditions. The model was validated using the experimental results obtained from the plant and two other circulating fluidized bed biomass gasifiers (CFBBGs). Finally, an ASPEN PLUS simulation model of biomass gasification was presented based on minimization of the Gibbs free energy of the reaction system at chemical equilibrium. Hydrodynamics plays a crucial role in defining the performance of gas-solid circulating fluidized beds (CFBs). A 2-dimensional mathematical model was developed considering the hydrodynamic behavior of CFB gasifiers. In the modeling, the CFB riser was divided into two regions: a dense region at the bottom and a dilute region at the top of the riser. Kunii and Levenspiel (1991)'s model was adopted to express the vertical solids distribution with some other assumptions. Radial distributions of bed voidage were taken into account in the upper zone by using Zhang et al. (1991)'s correlation. For model validation purposes, a cold model CFB was employed, in which sawdust was transported with air as the fluidizing agent. A comprehensive mathematical model was developed to predict the overall performance of a 1.2 MWe biomass gasification and power generation demonstration plant in China. Hydrodynamics as well as chemical reaction kinetics were considered. The fluidized bed riser was divided into two distinct sections: (a) a dense region at the bottom of the bed where biomass undergoes mainly heterogeneous reactions and (b) a dilute region at the top where most of homogeneous

  9. Tube erosion in bubbling fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E.K. [Lehigh Univ., Bethlehem, PA (United States). Energy Research Center; Stallings, J.W. [Electric Power Research Inst., Palo Alto, CA (United States)

    1991-12-31

    This paper reports on experimental and theoretical studies that were preformed of the interaction between bubbles and tubes and tube erosion in fluidized beds. The results are applicable to the erosion of horizontal tubes in the bottom row of a tube bundle in a bubbling bed. Cold model experimental data show that erosion is caused by the impact of bubble wakes on the tubes, with the rate of erosion increasing with the velocity of wake impact with the particle size. Wake impacts resulting from the vertical coalescence of pairs of bubbles directly beneath the tube result in particularly high rates of erosion damage. Theoretical results from a computer simulation of bubbling and erosion show very strong effects of the bed geometry and bubbling conditions on computed rates of erosion. These results show, for example, that the rate of erosion can be very sensitive to the vertical location of the bottom row of tubes with respect to the distributor.

  10. Nucla circulating atmospheric fluidized bed demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-31

    During the fourth quarter of 1990, steady-state performance testing at the Nucla Circulating Fluidized Bed (CFB) resumed under sponsorship of the US Department of Energy. Co-sponsorship of the Demonstration Test Program by the Electric Power Research Institute (EPRI) was completed on June 15, 1990. From October through December, 1990, Colorado-Ute Electric Association (CUEA) completed a total of 23 steady-state performance tests, 4 dynamic tests, and set operating records during November and December as the result of improved unit operating reliability. Highlight events and achievements during this period of operation are presented.

  11. CFD study of a fluidized bed

    OpenAIRE

    Lundberg, Joachim

    2008-01-01

    The aim of this thesis is to investigate the momentum exchange between the phases in a bubbling fluidized bed. The momentum exchange can be described by a drag model. Several drag models with different assumptions are developed. The drag models investigated in this work is the Syamlal O’Brien model, the Gidaspow model, Hill Koch Ladd model, the RUC model and an iterative version of the Syamlal O’Brien called the Richardson Zaki model. The models have been derived and studied in de...

  12. Transients in a circulating fluidized bed boiler

    Science.gov (United States)

    Baskakov, A. P.; Munts, V. A.; Pavlyuk, E. Yu.

    2013-11-01

    Transients in a circulating fluidized bed boiler firing biomass are considered. An attempt is made to describe transients with the use of concepts applied in the automatic control theory. The parameters calculated from an analysis of unsteady heat balance equations are compared with the experimental data obtained in the 12-MW boiler of the Chalmers University of Technology. It is demonstrated that these equations describe the transient modes of operation with good accuracy. Dependences for calculating the time constants of unsteady processes are obtained.

  13. SIMULATION OF PARTICLE COATING IN THE SUPERCRITICAL FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Carsten Vogt; Ernst-Ulrich Hartge; Joachim Werther; Gerd Brunner

    2005-01-01

    Fluidized bed technology using supercritical carbon dioxide both as a fluidizing gas and as a solvent for the coating material makes possible the production of thin, uniform and solvent-free coatings. But operation at low fluidizing velocities, which is favorable to facilitate gas cleaning under the high pressure conditions, may lead to uneven distribution of the coating in the fluidized bed and to unstable operation due to agglomeration. Therefore a model has been developed which describes local fluid dynamics within the high pressure fluidized bed. Based on this model, the coating process is described and the distribution of the coating inside the fluidized bed is calculated. Furthermore a submodel for the calculation of local concentrations of liquid paraffin has been set up, which may be used as a basis for the prediction of agglomeration and thus stability of operation.

  14. Some hydrodynamic aspects of 3-phase inverse fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Hydrodynamics of 3-phase inverse fluidized bed is studied experimentally using low density particles for different liquid and gas velocities.The hydrodynamic characteristics studied include pressure drop, minimum liquid and gas fluidization velocities and phase holdups. The minimum liquid fluidization velocity determined using the bed pressure gradient, decreases with increase in gas velocity. The axial profiles of phase holdups shows that the liquid holdup increases along the bed height, whereas the solid holdup decreases down the bed. However, the gas holdup is almost uniform in the bed.

  15. PREDICTION OF FLOW REGIMES IN SPOUT-FLUIDIZED BEDS

    Institute of Scientific and Technical Information of China (English)

    Jiyu Zhang; Fengxiang Tang

    2006-01-01

    Five main flow regimes in spout-fluidized bed were identified in this study, namely, fixed bed, spout with aeration, spout-fluidization, jet in fluidized bed and slugging, together with their corresponding major frequencies translated from pressure signals. The empirical equation A=aBb, in which A=Fr* /(H/Di) and B=(Fr*/(H/D))/(μg/μmf) are respectively the spout-geometry and spout-geometry-fluidization dimensionless numbers, was proposed to distinguish these flow regimes.

  16. A Numerical Model of a Microwave Heated Fluidized Bed

    OpenAIRE

    Faucher, Florent Patrice

    1998-01-01

    This proposes a model for a microwave heated fluidized bed by ceramic pellets to highlight the possibility to obtain a temperature gradient between the gas and the pellets. After a review of the recent work on microwave effects on chemical reactions, a short description of fluidization is given for a better understanding of the phenomena, followed by a development of a model of the heat transfer processes taking place in the fluidized bed. A parameter study describ...

  17. Collecting aerosol in airflow with a magnetically stabilized fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A magnetically stabilized fluidized bed (MSB) is a highly efficient filter that takes the advantage of both fluidized beds and fixed beds. This paper presents the research to collect aerosol in airflow with a MSB. The filtering model of MSB is established with its parameters including magnetic field intensity,gas superficial velocity, average grain-size, and bed height on thecollection efficiency of MSB. The model is verified by experiments.

  18. Particle transport in fluidized beds : experiments and stochastic models

    NARCIS (Netherlands)

    Dechsiri, Chutima

    2004-01-01

    Fluidization is a process in which solids are caused to behave like fluid by blowing gas or liquid upwards through the solid-filled reactor. The behavior of a bed of particles within the reactor during the process is very complex and difficult to predict. To make sure that a fluidized bed reactor is

  19. Pressure Fluctuations as a Diagnostic Tool for Fluidized Beds

    Energy Technology Data Exchange (ETDEWEB)

    Ethan Bure; Joel R. Schroeder; Ramon De La Cruz; Robert C. Brown

    1998-05-01

    The purpose of this project was to investigate the origin of pressure fluctuations in fluidized bed systems. The study assessed the potential for using pressure fluctuations as an indicator of fluidized bed hydrodynamics in both laboratory scale cold-models and industrial scale boilers. Both bubbling fluidized beds and circulating fluidized beds were evaluated. Testing including both cold-flow models and laboratory and industrial-scale combustors operating at elevated temperatures. The study yielded several conclusions on the relationship of pressure fluctuations and hydrodynamic behavior in fluidized beds. The study revealed the importance of collecting sufficiently long data sets to capture low frequency (on the order of 1 Hz) pressure phenomena in fluidized beds. Past research has tended toward truncated data sets collected with high frequency response transducers, which miss much of the spectral structure of fluidized bed hydrodynamics. As a result, many previous studies have drawn conclusions concerning hydrodynamic similitude between model and prototype fluidized beds that is insupportable from the low resolution data presented.

  20. Fluidization and coating of very dense powders by fluidized bed chemical vapour deposition

    OpenAIRE

    Rodriguez, Philippe; Caussat, Brigitte; Ablitzer, Carine; Iltis, Xavière; Brothier, Méryl

    2013-01-01

    The hydrodynamic behaviour of a very dense tungsten powder, 75 µm in median diameter and 19,300 kg/m3 in grain density, has been studied in a fluidized bed at room temperature using nitrogen and argon as carrier gas. Even if fluidization was achieved, the small bed expansion indicated that it was imperfect. Then, the fluidization was studied at 400 °C in order to investigate the feasibility of coating this powder by Fluidized Bed Chemical Vapour Deposition (FBCVD). In particular, the influenc...

  1. Flow Pattern in a Fluidized Bed with a Non-fluidized Zone

    DEFF Research Database (Denmark)

    Lin, Weigang; Dam-Johansen, Kim; Van den Bleek, Cor. M.

    1997-01-01

    The flow pattern of a fluidized bed with non-fluidized zones is investigated both experimentally and theoretically. Experiments were carried out in such a way that air was introduced only through part of the distributor. The results show a significant amount of air flowing to the zone where no air...... over the bed. Very good agreement between the experimental and calculated results is achieved without any fitting parameter. The results are relevant to the understanding of heat transfer behaviour of a fluidized bed combustor (FBC) that is only partly fluidized to control its load....

  2. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    张利斌; 李修伦

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39 mm ID and 2.0 m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum.The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  3. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39mm ID and 2.0m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum. The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  4. Study of Fluidized-Bed Control Rods

    International Nuclear Information System (INIS)

    Control of nuclear reactors with fluidized-bed control rods (FBCR) has been previously proposed; but, despite some apparent advantages over electromechanical systems, such rods have not received widespread attention. With the FBCR concept, the reactor control system becomes a flow-regulating system using either variable-speed pumps or motor-driven control valves in the main coolant. Alternatively, in-core by-pass piping similar to control systems now being developed for fluidized-bed reactors may be utilized. Some of the possible advantages of the FBCR concept are as follows: (1) Most pressure-vessel head penetrations are eliminated, and refueling is simplified; (2) Automatic scram results from a loss-of-flow accident; (3) Axial power can be shaped by the use of contoured channels or variable-sized particles; (4). Water-gap flux peaking can be reduced for the partially withdrawn control rod; (5) The temperature reactivity allowance may be reduced if the fluidized control rods have a negative temperature coefficient; and (6) Fabrication costs are much lower than for electromechanical systems. An evaluation of the FBCR concept, including construction of prototype models and testing of the hydraulic and nuclear characteristics, has been performed. Two types of rods were studied: transmission rods (thickness ≦ 2 mean-free-paths) and reflection rods (thickness ≦ 4 mean-free-paths). Acceptable hydraulic and nuclear characteristics are possible with both types. The feasibility of controlling low-power reactors by either transmission- or reflection-type fluidized.-bed control rods has been established. Furthermore, it was shown that the FBCR concept has good control properties which may be calculated by standard theoretical methods. For high-power, high-temperature applications, additional information on particle material characteristics is needed. A great advantage offered by the FBCR is the possibility of shaping the axial flux either by the use of particles of

  5. Stabilizing effect of plasma discharge on bubbling fluidized granular bed

    Science.gov (United States)

    Hu, Mao-Bin; Dang, Sai-Chao; Ma, Qiang; Xia, Wei-Dong

    2015-07-01

    Fluidized beds have been widely used for processing granular materials. In this paper, we study the effect of plasma on the fluidization behavior of a bubbling fluidized bed with an atmospheric pressure plasma discharger. Experiment results show that the bubbling fluidized bed is stabilized with the discharge of plasma. When the discharge current reaches a minimum stabilization current Cms, air bubbles in the bed will disappear and the surface fluctuation is completely suppressed. A simplified model is proposed to consider the effect of electric Coulomb force generated by the plasma. It is found that the Coulomb force will propel the particles to move towards the void area, so that the bubbling fluidized bed is stabilized with a high enough plasma discharge. Project supported by the National Natural Science Foundation of China (Grant Nos. 11035005 and 11034010).

  6. Fluidized bed combustion: mixing and pollutant limitation

    Energy Technology Data Exchange (ETDEWEB)

    Leckner, B. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Energy Conversion

    1997-10-01

    Fluidized bed combustion (FBC) has been applied commercially during a few decades, and sufficient knowledge is gained to design boilers with sizes of up to several hundreds of megawatt thermal power (MW{sub th}). The knowledge of what goes on inside a large combustion chamber is still limited, however, and this impedes further optimization and efficient solution of problems that might occur. Despite this lack of knowledge the present survey deals with combustion chamber processes and discusses mixing and distribution of fuel and air in the combustion chamber and its importance for sulphur capture and reduction of emissions of nitrogen oxides. It is desirable to present the material in a general way and to cover the entire field of FBC. However, the scarce openly published information deals mostly with coal combustion in atmospheric circulating fluidized bed (CFB) combustors, and therefore this application will receive most attention, but reference is also made to pressurized combustion and to other fuels than coal. In this context the important work made in the LIEKKI project on the analysis of different fuels and on the influence of pressure should be especially pointed out. (orig.)

  7. Evaluation of Fluidized Bed Reactor in treating Dyeing effluent

    Directory of Open Access Journals (Sweden)

    S. Poongoth

    2012-07-01

    Full Text Available Textile dyeing industries one of the complicated industries which use many chemicals like dyes, starch, acids, alkalis, surfactants and refractory organics for their process. As it is a wet process it requires more amount of water ranging 65-104 L/Kg of product and it discharges 52-95 L/Kg of product as wastewater. The COD, BOD,TDS, Colour and SS are the major pollutants from these industries to the receiving streams. Biological treatment is employed mostly when compared to the physicochemical treatment. More sludge, toxic bye products and cost for the treatment are the reasons for not employing the physiochemical treatment processes. Biological treatments like aerobic and anaerobic processes overcome the disadvantages of physicochemical treatment. The present study evaluates the Aerobic Fluidized bed Reactor for the treatment of Dyeing effluent. It has been observed through this study that 89% colour removal and 83.3% COD removal were achieved.

  8. RESEARCH ON DENSITY STABILITY OF AIR DENSE MEDIUM FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    骆振福; 陈清如

    1994-01-01

    In this papcr on thc basis of studying the distribution of fine coal in the dense medium fluidized bed, the optimal size range of fine coal, which constitutes a fluidized bed together with the dense medium, has been found. In the separating process the fine coal will continuously accumulate in fluidized bed, thus inevitably reducing the density of the bed. In order to keep bed density stable, the authors adopted such measures as split-flow of used medium and complement of fresh dense medium. The experiment results in both lab and pilot systems of the air-dense medium fluidized bed show that these measures are effective and satisfactory. Then authors also have established some relative dynamic mathematical models for it.

  9. Fluidized-bed calciner with combustion nozzle and shroud

    Science.gov (United States)

    Wielang, Joseph A.; Palmer, William B.; Kerr, William B.

    1977-01-01

    A nozzle employed as a burner within a fluidized bed is coaxially enclosed within a tubular shroud that extends beyond the nozzle length into the fluidized bed. The open-ended shroud portion beyond the nozzle end provides an antechamber for mixture and combustion of atomized fuel with an oxygen-containing gas. The arrangement provides improved combustion efficiency and excludes bed particles from the high-velocity, high-temperature portions of the flame to reduce particle attrition.

  10. Internal dust recirculation system for a fluidized bed heat exchanger

    Science.gov (United States)

    Gamble, Robert L.; Garcia-Mallol, Juan A.

    1981-01-01

    A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided in a heat exchange relation to the bed and includes a steam drum disposed adjacent the bed and a tube bank extending between the steam drum and a water drum. The tube bank is located in the path of the effluent gases exiting from the bed and a baffle system is provided to separate the solid particulate matter from the effluent gases. The particulate matter is collected and injected back into the fluidized bed.

  11. Fluidized bed heat exchanger utilizing angularly extending heat exchange tubes

    Science.gov (United States)

    Talmud, Fred M.; Garcia-Mallol, Juan-Antonio

    1980-01-01

    A fluidized bed heat exchanger in which air is passed through a bed of particulate material containing fuel disposed in a housing. A steam/water natural circulation system is provided and includes a steam drum disposed adjacent the fluidized bed and a series of tubes connected at one end to the steam drum. A portion of the tubes are connected to a water drum and in the path of the air and the gaseous products of combustion exiting from the bed. Another portion of the tubes pass through the bed and extend at an angle to the upper surface of the bed.

  12. Fluidized bed combustion research in Turkey

    International Nuclear Information System (INIS)

    At present 20% of the total energy consumption in Turkey is met by combustion of lignites. The amount of lignite utilization in the total energy consumption in the year 2000 is expected to double compared to the present. The prevalent characteristics of Turkish lignites are high volatile matter, moisture, ash, and sulfur contents and low calorific value. Also, there are combustion difficulties in conventional combustors associated with the low ash sintering temperatures. For these reasons, there is a major air pollution problem in the main cities of Turkey during winter months. In this paper, the authors review the fluidized bed combustion research work undertaken in Turkey in the last decade and discuss the relevant problem of volatile matter combustion, stability and design

  13. Nucla circulating atmospheric fluidized bed demonstration project

    Energy Technology Data Exchange (ETDEWEB)

    Keith, Raymond E.

    1991-10-01

    Colorado-Ute Electric Association began a study to evaluate options for upgrading and extending the life of its Nucla power station in 1982. Located in southwestern Colorado near the town of Nucla, this station was commissioned in 1959 with a local bituminous coal as its design fuel for three identical stoker-fired units, each rated at 12.6 MW(e). Poor station efficiency, high fuel costs, and spiraling boiler maintenance costs forced the Nucla Station into low priority in the CUEA dispatch order as early as 1981. Among the options CUEA considered was to serve as a host utility to demonstrate Atmospheric Fluidized Bed Combustion (AFBC) technology. The anticipated environmental benefits and apparent attractive economics of a circulating AFBC led to Colorado-Ute's decision to proceed with the design and construction of a demonstration project in 1984 at the Nucla facility.

  14. NUCLA Circulating Atmospheric Fluidized Bed Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    Keith, Raymond E.; Heller, Thomas J.; Bush, Stuart A.

    1991-01-01

    This Annual Report on Colorado-Ute Electric Association's NUCLA Circulating Fluidized Bed (CFB) Demonstration Program covers the period from February 1987 through December 1988. The outline for presentation in this report includes a summary of unit operations along with individual sections covering progress in study plan areas that commenced during this reporting period. These include cold-mode shakedown and calibration, plant commercial performance statistics, unit start-up (cold), coal and limestone preparation and handling, ash handling system performance and operating experience, tubular air heater, baghouse operation and performance, materials monitoring, and reliability monitoring. During this reporting period, the coal-mode shakedown and calibration plan was completed. (VC)

  15. PRESSURE FLUCTUATIONS IN GAS-SOLIDS FLUIDIZED BEDS

    Institute of Scientific and Technical Information of China (English)

    Hsiaotao Bi; Aihua Chen

    2003-01-01

    Pressure fluctuation data measured in a series of fluidized beds with diameters of 0.05, 0.1, 0.29, 0.60 and 1.56 m showed that the maximum amplitude or standard deviation increased with increasing the superficial gas velocity and static bed height for relatively shallow beds and became insensitive to the increase in static bed height in relatively deep beds. The amplitude appeared to be less dependent on the measurement location in the dense bed. Predictions based on bubble passage, bubble eruption at the upper bed surface and bed oscillation all failed to explain all observed trends and underestimated the amplitude of pressure fluctuations, suggesting that the global pressure fluctuations in gas-solids bubbling fluidized beds are the superposition of local pressure variations, bed oscillations and pressure waves generated from the bubble formation in the distributor region, bubble coalescence during their rise and bubble eruption at the upper bed surface.

  16. Kinetics of Reduction Reaction in Micro-Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    LINYin-he; GUOZhan—cheng; TANGHui—qing; REN Shan; LIJing—wei

    2012-01-01

    Micro-fluidized bed reactor is a new research method for the reduction of iron ore fines. The reactor is op- erated as a differential reactor to ensure a constant gas concentration and temperature within the reactor volume. In order to understand the dynamic process of the reduction reaction in micro-fluidized bed, a series of kinetic experi- ments were designed. In the micro fluidized bed, the use of shrinking core model describes the dynamic behavior of reduction of iron ore. And the apparent activation energy is calculated in the range of 700--850 ~C while the initial atmosphere is 100% content of CO.

  17. Propylene polymerization in a circulating slugging fluidized bed reactor

    NARCIS (Netherlands)

    Putten, van Inge Cornelia

    2004-01-01

    The work presented in this thesis is concerned with research on the riser of a circulating fluidized bed system for olefin polymerization. In the riser section, fluidization takes place in the transporting slugging mode and polymer particles are produced in the riser in a non-isothermal way. Propert

  18. Limestone fragmentation and attrition during fluidized bed oxyfiring

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Piero Salatino [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy)

    2010-04-15

    Attrition/fragmentation of limestone under simulated fluidized bed oxyfiring conditions was investigated by means of an experimental protocol that had been previously developed for characterization of attrition/fragmentation of sorbents in air-blown atmospheric fluidized bed combustors. The protocol was based on the use of different and mutually complementary techniques. The extent and pattern of attrition by surface wear in the dense phase of a fluidized bed were assessed in experiments carried out with a bench scale fluidized bed combustor under simulated oxyfiring conditions. Sorbent samples generated during simulated oxyfiring tests were further characterized from the standpoint of fragmentation upon high velocity impact by means of a purposely designed particle impactor. Results showed that under calcination-hindered conditions attrition and fragmentation patterns are much different from those occurring under air-blown atmospheric combustion conditions. Noteworthy, attrition/fragmentation enhanced particle sulfation by continuously regenerating the exposed particle surface. 13 refs., 8 figs.

  19. Feedback linearizing control of a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Aoufoussi, H.; Perrier, M.; Chaouki, J.; Chavarie, C.; Dochain, D. (Ecole Polytechnique de Montreal, Montreal, PQ (Canada). Dept. de Genie Chimique)

    1992-04-01

    A linearized technique has been applied to temperature control for a fluidized bed reactor. A nonlinear antiwindup mechanism for the reset action is used. Simulation tests show that the controller provides good setpoint tracking. 24 refs.; 11 figs.; 4 tabs.

  20. Model of Fluidized Bed Containing Reacting Solids and Gases

    Science.gov (United States)

    Bellan, Josette; Lathouwers, Danny

    2003-01-01

    A mathematical model has been developed for describing the thermofluid dynamics of a dense, chemically reacting mixture of solid particles and gases. As used here, "dense" signifies having a large volume fraction of particles, as for example in a bubbling fluidized bed. The model is intended especially for application to fluidized beds that contain mixtures of carrier gases, biomass undergoing pyrolysis, and sand. So far, the design of fluidized beds and other gas/solid industrial processing equipment has been based on empirical correlations derived from laboratory- and pilot-scale units. The present mathematical model is a product of continuing efforts to develop a computational capability for optimizing the designs of fluidized beds and related equipment on the basis of first principles. Such a capability could eliminate the need for expensive, time-consuming predesign testing.

  1. FLUIDIZATION OF FINE POWDERS IN FLUIDIZED BEDS WITH AN UPWARD OR A DOWNWARD AIR JET

    Institute of Scientific and Technical Information of China (English)

    Ruoyu Hong; Jianmin Ding; Hongzhong Li

    2005-01-01

    The hydrodynamic behavior of fine powders in jet-fluidized beds was studied numerically and experimentally. The starting point of numerical simulation was the generalized Navier-Stokes (N-S) equations for the gas and solids phases. The κ-εturbulence model was used for high-speed gas jets in fluidized beds. Computation shows that a suitable turbulence model is necessary to obtain agreement between the simulation and literature experimental data for a high-speed gas jet. The model was applied to simulating the fluidization of fine powders in fluidized beds with an upward or a downward air jet. An empirical cohesion model was obtained by correlating the cohesive force between fine particles using a cohetester. The cohesion model was embedded into the two-fluid model to simulate the fluidization of fine powders in two-dimensional (2-D) beds. To study the fluidization behavior of fine and cohesive powders with a downward jet,experiments were performed in a 2-D bed. Agreement between the computed time-averaged porosity and measured data was obtained. With an upward jet in the bed center, the measured and computed porosities show a dilute central core, especially at very high jet velocities. Based on our experiments and computations, a downward jet located inside the bed is recommended to achieve better mixing and contacting of gas and solids.

  2. Temperature distribution and control in liquefied petroleum gas fluidized beds

    Institute of Scientific and Technical Information of China (English)

    Li Wang; Ping Wu; Yanping Zhang; Jing Yang; Lige Tong

    2004-01-01

    Temperature distribution and control have been investigated in a liquefied petroleum gas (LPG) fluidized bed with hollow corundum spheres (A12O3) of 0.867-1.212 mm in diameter at moderately high temperatures (800-1100℃). Experiments were carried out for the air consumption coefficient α in the range of 0.3 to 1.0 and the fluidization number N in the range of 1.3 to 3.0. Particle properties, initial bed height, α and N all affect temperature distribution in the bed. Bed temperature can be adjusted about 200℃ by combined the adjusting of α and N.

  3. Fluidized-bed pyrolysis of waste bamboo

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Bamboo was a popular material substituting for wood, especially for one-off commodity in China. In order to recover energy and materials from waste bamboo, the basic characteristics of bamboo pyrolysis were studied by a thermogravimetric analyzer. It implied that the reaction began at 190~210 ℃, and the percentage of solid product deceased from about 25% to 17% when temperature ranged from 400 ℃ to 700 ℃. A lab-scale fluidized-bed furnace was setup to research the detailed properties of gaseous, liquid and solid products respectively. When temperature increased from 400 ℃ to 700 ℃, the mass percent of solid product decreased from 27% to 17% approximately, while that of syngas rose up from 19% to 35%. When temperature was about 500℃, the percentage of tar reached the top, about 31%. The mass balance of these experiments was about 93%~95%. It indicated that three reactions involved in the process: pyrolysis of exterior bamboo, pyrolysis of interior bamboo and secondary pyrolysis of heavy tar.

  4. Fluidized bed combustion of pesticide-manufacture liquid wastes

    Directory of Open Access Journals (Sweden)

    SAŠA MILETIĆ

    2010-04-01

    Full Text Available Industrial liquid wastes can be in the form of solutions, suspensions, sludges, scums or waste oil and have organic properties. The objective of this work was to demonstrate the technical feasibility of a fluidized bed as a clean technology for burning liquid waste from a pesticide production plant. The combustion of liquid waste mixtures, obtained from realistic samples, was investigated in a pilot scale fluidized bed with quartz sand particles of 0.63–1.25 mm in diameter and 2610 kg/m3 in density at 800–950 °C. To ensure complete combustion of liquid waste and additional fuel, the combustion chamber was supplied with excess air and the U/UmF (at ambient temperature was in between 1.1 and 2.3. In the fluidized bed chamber, liquid waste, additional liquid fuel and air can be brought into intense contact sufficient to permit combustion in bed without backfire problems. The experimental results show that the fluidized bed furnace offers excellent thermal uniformity and temperature control. The results of the combustion tests showed that degradation of liquid wastes can be successfully realized in a fluidized bed with no harmful gaseous emissions by ensuring that the temperatures of both the bed and the freeboard are not lower than 900 °C.

  5. DRYING OF GRANULAR MATERIALS IN AGITATED FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    An experimental study of the drying characteristics of an agitated fluidized bed dryer is presented and discussed. In the study, the citric acid particles were used as bed material with the diameters ranging from 0.2mm to 1.3mm. The variables affecting apparently the drying rate were found to be the mass flow rate, the inlet air temperature, the rotary speed of agitating mechanism and the particles feed rate. Comparing with other variables considered, mass flow rate was found to have the least important influence on the drying rate. The agitated fluidized bed dryer is suitable to drying agglomerating or sticky materials.

  6. Development of methanogenic consortia in fluidized-bed batches using sepiolite of different particle size.

    Science.gov (United States)

    Sánchez, J M; Rodríguez, F; Valle, L; Muñoz, M A; Moriñigo, M A; Borrego, J J

    1996-09-01

    The addition of support materials, such as sepiolite, to fluidized-bed anaerobic digesters enhances the methane production by increasing the colonization by syntrophic microbiota. However, the efficiency in the methanogenesis depends on the particle size of the support material, the highest level of methane production being obtained by the smaller particle size sepiolite. Because of the porosity and physico-chemical characteristics of these support materials, the anaerobic microbial consortia formed quickly (after one week of incubation). The predominant methanogenic bacteria present in the active granules, detected both by immunofluorescence using specific antibodies and by scanning electron microscopy, were acetoclastic methanogens, mainly Methanosarcina and Methanosaeta.

  7. Experimental study of fluidized bed agglomeration of acerola powder

    Directory of Open Access Journals (Sweden)

    G. C. Dacanal

    2008-03-01

    Full Text Available The aim of this work was to study the main effects of acerola powder on fluidized bed agglomeration. A 2(4-1 fractional factoring design was used to evaluate the main operating conditions (fluidizing air temperature, fluidizing air velocity, atomizing air flow and height of nozzle in the bed. The mechanical and physicochemical product changes were determined by analysis of particle diameter, moisture content, wetting time and bed porosity. The particle enlargement by agglomeration occurred when the relative humidity in the bed increased and, thus, the moisture of the product increased. However, the excessive increase in relative humidity resulted in a decrease in yield, caused by caking and product incrustation. The consolidation of small granules resulted in an increase in the instant properties, decreasing the wetting time and increasing the solubility in a short period of agitation.

  8. Torrefaction of sawdust in a fluidized bed reactor.

    Science.gov (United States)

    Li, Hui; Liu, Xinhua; Legros, Robert; Bi, Xiaotao T; Lim, C J; Sokhansanj, Shahab

    2012-01-01

    In the present work, stable fluidization of sawdust was achieved in a bench fluidized bed with an inclined orifice distributor without inert bed materials. A solids circulation pattern was established in the bed without the presence of slugging and channeling. The effects of treatment severity and weight loss on the solid product properties were identified. The decomposition of hemicelluloses was found to be responsible for the significant changes of chemical, physical and mechanical properties of the torrefied sawdust, including energy content, particle size distribution and moisture absorption capacity. The hydrophobicity of the torrefied sawdust was improved over the raw sawdust with a reduction of around 40 wt.% in saturated water uptake rate, and enhanced with increasing the treatment severity due to the decomposition of hemicelluloses which are rich in hydroxyl groups. The results in this study provided the basis for torrefaction in fluidized bed reactors.

  9. Bed dynamics of gas-solid fluidized bed with rod promoter

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The dynamic characteristics of a gas-solid fluidized bed with different rod promoters have been investigated in terms of bed expansion and fluctuation, minimum fluidization velocity and distributor-to-bed pressure drop ratio at minimum fluidization velocity. Experimentation based on statistical design has been carried out and model equations using factorial design of experiments have been developed for the above mentioned quantities for a promoted gas-solid fluidized bed. The model equations have been tested with additional experimental data. The system variables include four types of rod promoters of varying blockage volume, bed particles of four sizes and four initial static bed heights. A comparison between the predicted values of the output variables using the proposed model equation with their corresponding experimental ones shows fairly good agreement.

  10. FLUIDIZED BED STEAM REFORMER MONOLITH FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-12-22

    Fluidized Bed Steam Reforming (FBSR) is being considered as an alternative technology for the immobilization of a wide variety of aqueous high sodium containing radioactive wastes at various DOE facilities in the United States. The addition of clay, charcoal, and a catalyst as co-reactants converts aqueous Low Activity Wastes (LAW) to a granular or ''mineralized'' waste form while converting organic components to CO{sub 2} and steam, and nitrate/nitrite components, if any, to N{sub 2}. The waste form produced is a multiphase mineral assemblage of Na-Al-Si (NAS) feldspathoid minerals with cage-like structures that atomically bond radionuclides like Tc-99 and anions such as SO{sub 4}, I, F, and Cl. The granular product has been shown to be as durable as LAW glass. Shallow land burial requires that the mineralized waste form be able to sustain the weight of soil overburden and potential intrusion by future generations. The strength requirement necessitates binding the granular product into a monolith. FBSR mineral products were formulated into a variety of monoliths including various cements, Ceramicrete, and hydroceramics. All but one of the nine monoliths tested met the <2g/m{sup 2} durability specification for Na and Re (simulant for Tc-99) when tested using the Product Consistency Test (PCT; ASTM C1285). Of the nine monoliths tested the cements produced with 80-87 wt% FBSR product, the Ceramicrete, and the hydroceramic produced with 83.3 wt% FBSR product, met the compressive strength and durability requirements for an LAW waste form.

  11. Materials performance in fluidized-bed air heaters

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Podolski, W.

    1991-12-01

    Development of cogeneration systems that involve combustion of coal in a fluidized bed and use of air heaters to generate hot air for turbine systems has been in progress for a number of years. The US Department of Energy (DOE) sponsored the Atmospheric Fluidized-Bed Cogeneration Air Heater Experiment (ACAHE) to assess the performance of various heat exchanger materials and establish confidence in the resultant designs of fluidized-bed-combustion air heater systems. Westinghouse Electric Corporation, in association with Babcock & Wilcox, Foster Wheeler, and ABB/Combustion Engineering, prepared specifications and hardware for the ACAHE. Argonne National Laboratory, through a contract with the Rocketdyne Division of Rockwell International, conducted tests in the DOE 1.8 {times} 1.8 m atmospheric fluidized-bed combustion facility in El Segundo, California. This paper presents an assessment of the materials performance in fluidized bed environments and examines guidelines for materials selection on the basis of corrosion resistance in air and in combustion environments, mechanical properties, fabricability/thermal stability, and cost.

  12. Materials performance in fluidized-bed air heaters

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Podolski, W.

    1991-12-01

    Development of cogeneration systems that involve combustion of coal in a fluidized bed and use of air heaters to generate hot air for turbine systems has been in progress for a number of years. The US Department of Energy (DOE) sponsored the Atmospheric Fluidized-Bed Cogeneration Air Heater Experiment (ACAHE) to assess the performance of various heat exchanger materials and establish confidence in the resultant designs of fluidized-bed-combustion air heater systems. Westinghouse Electric Corporation, in association with Babcock Wilcox, Foster Wheeler, and ABB/Combustion Engineering, prepared specifications and hardware for the ACAHE. Argonne National Laboratory, through a contract with the Rocketdyne Division of Rockwell International, conducted tests in the DOE 1.8 {times} 1.8 m atmospheric fluidized-bed combustion facility in El Segundo, California. This paper presents an assessment of the materials performance in fluidized bed environments and examines guidelines for materials selection on the basis of corrosion resistance in air and in combustion environments, mechanical properties, fabricability/thermal stability, and cost.

  13. Concepts of Emission Reduction in Fluidized Bed Combustion of Biomass

    Directory of Open Access Journals (Sweden)

    Amon Purgar

    2012-01-01

    Full Text Available A status report on fluidized bed technology in Austria is under preparation, in response to the Fluidized Bed Conversion multi-lateral technology initiative of the International Energy Agency. This status report focuses on the current operation of fluidized bed combustors. Combustors have been installed in the following industrial sectors: pulp and paper, biomass heat and power plants, waste-to-energy plants, and communal sewage sludge treatment plants. There are also some small demonstration plants. These plants all have in common that they treat renewable fuel types. In many cases, only bio-fuels are treated. Besides the ability to burn a wide range of low-grade and difficult fuels, fluidized bed combustors have the advantages of low NOX emissions and the possibility of in-process capture of SO2. Various emission reduction concepts for fluidized bed combustors that are typical for their industrial sector are discussed. The discussion of these concepts focuses on NOX, SO2 and dust.

  14. Mathematical model of processes of reactor with gasified fluidized bed

    International Nuclear Information System (INIS)

    An original scheme of steam generator with gasifying fluidized bed has been presented as a possible solution for reconstruction of furnace with pulverized burning of coal. The method is effective when applied in combination with desulfurization for the purpose of reducing the CO2 emissions level. A mathematical model has been developed, which determines the correlation primary (fluidizing) and (burning out) secondary air with sufficient for the practice accuracy

  15. Numerical Modeling and Prediction of Bubbling Fluidized Beds

    OpenAIRE

    England, Jonas Andrew

    2011-01-01

    Numerical modeling and prediction techniques are used to determine pressure drop, minimum fluidization velocity and segregation for bubbling fluidized beds. The computational fluid dynamics (CFD) code Multiphase Flow with Interphase eXchange (MFIX) is used to study a two-stage reactor geometry with a binary mixture. MFIX is demonstrated to accurately predict pressure drop versus inlet gas velocity for binary mixtures. A new method is developed to predict the pressure drop versus inlet gas v...

  16. Computational fluid dynamic modeling of fluidized-bed polymerization reactors

    Energy Technology Data Exchange (ETDEWEB)

    Rokkam, Ram [Iowa State Univ., Ames, IA (United States)

    2012-01-01

    Polyethylene is one of the most widely used plastics, and over 60 million tons are produced worldwide every year. Polyethylene is obtained by the catalytic polymerization of ethylene in gas and liquid phase reactors. The gas phase processes are more advantageous, and use fluidized-bed reactors for production of polyethylene. Since they operate so close to the melting point of the polymer, agglomeration is an operational concern in all slurry and gas polymerization processes. Electrostatics and hot spot formation are the main factors that contribute to agglomeration in gas-phase processes. Electrostatic charges in gas phase polymerization fluidized bed reactors are known to influence the bed hydrodynamics, particle elutriation, bubble size, bubble shape etc. Accumulation of electrostatic charges in the fluidized-bed can lead to operational issues. In this work a first-principles electrostatic model is developed and coupled with a multi-fluid computational fluid dynamic (CFD) model to understand the effect of electrostatics on the dynamics of a fluidized-bed. The multi-fluid CFD model for gas-particle flow is based on the kinetic theory of granular flows closures. The electrostatic model is developed based on a fixed, size-dependent charge for each type of particle (catalyst, polymer, polymer fines) phase. The combined CFD model is first verified using simple test cases, validated with experiments and applied to a pilot-scale polymerization fluidized-bed reactor. The CFD model reproduced qualitative trends in particle segregation and entrainment due to electrostatic charges observed in experiments. For the scale up of fluidized bed reactor, filtered models are developed and implemented on pilot scale reactor.

  17. Characterization of biofilm in 200W fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Michelle H. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Saurey, Sabrina D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Lee, Brady D. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Parker, Kent E. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Eisenhauer, Emalee E. R. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Cordova, Elsa A. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Golovich, Elizabeth C. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)

    2014-09-29

    Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry

  18. Characterization of Biofilm in 200W Fluidized Bed Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Michelle H.; Saurey, Sabrina D.; Lee, Brady D.; Parker, Kent E.; Eisenhauer, Emalee ER; Cordova, Elsa A.; Golovich, Elizabeth C.

    2014-09-29

    Contaminated groundwater beneath the 200 West Area at the Hanford Site in Southeast Washington is currently being treated using a pump and treat system to remove organics, inorganics, radionuclides, and metals. A granular activated carbon-based fluidized bed reactor (FBR) has been added to remove nitrate, hexavalent chromium and carbon tetrachloride. Initial analytical results indicated the microorganisms effectively reduced many of the contaminants to less than cleanup levels. However shortly thereafter operational upsets of the FBR include carbon carry over, over production of microbial extracellular polymeric substance (biofilm) materials, and over production of hydrogen sulfide. As a result detailed investigations were undertaken to understand the functional diversity and activity of the microbial community present in the FBR over time. Molecular analyses including terminal restriction fragment length polymorphism analysis, quantitative polymerase chain reaction and fluorescent in situ hybridization analyses were performed on the microbial community extracted from the biofilm within the bed and from the inoculum, to determine functional dynamics of the FBR bed over time and following operational changes. Findings from these analyses indicated: 1) the microbial community within the bed was completely different than community used for inoculation, and was likely from the groundwater; 2) analyses early in the testing showed an FBR community dominated by a few Curvibacter and Flavobacterium species; 3) the final sample taken indicated that the microbial community in the FBR bed had become more diverse; and 4) qPCR analyses indicated that bacteria involved in nitrogen cycling, including denitrifiers and anaerobic ammonia oxidizing bacteria, were dominant in the bed. These results indicate that molecular tools can be powerful for determining functional diversity within FBR type reactors. Coupled with micronutrient, influent and effluent chemistry evaluations, a more

  19. Parametric Study of NOx Emissions in Circulating Fluidized Bed Combustor

    International Nuclear Information System (INIS)

    Fluidized bed combustion behavior of coal and biomass is of practical interest due to its significant involvement in heating systems and power plant operations. This combustion behavior has been studied by many experimental techniques. . Use of biomass in coal-fired power plants results in high efficiencies and fuel diversity. Co-combustion experiments were carried out in a pilot scale test facility of circulating fluidized bed combustor (70KW). Effect of operating parameters on the NOx emissions is studied while burning coal with wheat straw. Relation between NOx emissions and operating parameters like bed temperature, excess air ratio, air staging, Ca/S molar ratio and fluidizing air velocity have been studied and discussed. (author)

  20. Metallic species derived from fluidized bed coal combustion. [59 references

    Energy Technology Data Exchange (ETDEWEB)

    Natusch, D.F.S.; Taylor, D.R.

    1980-01-01

    Samples of fly ash generated by the combustion of Montana Rosebud coal in an experimental 18 inch fluidized bed combustor were collected. The use of a heated cascade impactor permitted collection of size fractionated material that avoided condensation of volatile gases on the particles. Elemental concentration trends were determined as a function of size and temperature and the results compared to published reports for conventional power plants. The behavior of trace metals appears to be substantially different in the two systems due to lower operating temperatures and the addition of limestone to the fluidized bed. Corrosion of the impactor plates was observed at the highest temperature and lowest limestone feed rate sampled during the study. Data from the elemental concentration and leaching studies suggest that corrosion is most likely due to reactions involving sodium sulfate. However, it is concluded that corrosion is less of a potential problem in fluidized-bed systems than in conventional coal-fired systems.

  1. Thermal denitrification of evaporators concentrates in reactor with fluidized bed

    International Nuclear Information System (INIS)

    As part of the treatments of liquid wastes coming from the Marcoule reprocessing plant, the study of a thermal denitrification process for evaporator concentrates has been chosen by the CEA/CEN Cadarache: the fluidized-bed calcination. This work presents the study of a calcination pilot-plant for wastes with a very high sodium nitrate content. After a reactional analysis carried out in a thermobalance on samples which are representative of the fluidized-bed compounds, the perfecting of many of the plant parameters - such as the solution injection system - was carried out on a scale-model at first. Then, it was verified on the pilot-plant, and some experiments have been carried out. A mathematical model for the particle growth inside the fluidized-bed is proposed. (author). 179 refs., 65 figs., 23 tabs

  2. Enhanced durability of desulfurization sorbents for fluidized-bed applications

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, R.P.; Gangwal, S.K.

    1991-06-01

    Advanced integrated gasification combined cycle (IGCC) power systems require the development of high-temperature desulfurization sorbents capable of removing hydrogen sulfide from coal gasifier down to very low levels. The objective of this investigation was to identify and demonstrate methods for enhancing the long-term chemical reactivity and mechanical strength of zinc ferrite, a leading regenerable sorbent, for fluidized-bed applications. Fluidized sorbent beds offer significant potential in IGCC systems because of their ability to control the highly exothermic regeneration involved. However, fluidized beds require a durable, attrition-resistant sorbent in the 100--300 {mu}m size range. A bench-scale high-temperature, high- pressure (HTHP) fluidized-bed reactor (7.6-cm I.D.) system capable of operating up to 24 atm and 800{degree}C was designed, built and tested. A total of 175 sulfidation-regeneration cycles were carried out using KRW-type coal gas with various zinc ferrite formulations. A number of sorbent manufacturing techniques including spray drying, impregnation, crushing and screening, and granulation were investigated. While fluidizable sorbents prepared by crushing durable pellets and screening had acceptable sulfur capacity, they underwent excessive attrition during multicycle testing. The sorbent formulations prepared by a proprietary technique were found to have excellent attrition resistance and acceptable chemical reactivity during multicycle testing. However, zinc ferrite was found to be limited to 550{degree}C, beyond which excessive sorbent weakening due to chemical transformations, e.g., iron oxide reduction, was observed.

  3. Lagrangian-Eulerian simulation of slugging fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Guorong Wu; Jie Ouyang; Binxin Yang; Qiang Li; Fang Wang

    2012-01-01

    This work studies gas-solid slugging fluidized beds with Type-D particles,using two-dimensional simulations based on discrete element model (DEM).DEM performance is quantitatively validated by two commonly accepted correlations for determining slugging behavior.The voidage profiles simulated with bed height corresponding to Baeyens and Geldart (1974) correlation for onset of slugging demonstrate a transitional flow pattern from free bubbling to slugging.The present calculated values for the maximum slugging bed height are in good agreement with the correlation from Matsen et al.(1969).Simulations show that fluidized beds with Type-D particles can operate in the round-nosed slugging regime and also shows that wall slugs and square-nosed slugs tend to be formed with increase in superficial gas velocity and in bed height,respectively.

  4. Modeling of Sulfur Retention in Circulating Fluidized Bed Coal Combustors

    Institute of Scientific and Technical Information of China (English)

    乔锐; 吕俊复; 刘青; 吴学安; 岳光溪

    2001-01-01

    A comprehensive model for predicting the sulfur retention performance in circulating fluidized bedcombustors was developed which involves the different residence times, the wide particle size distribution andthe different forms of sulfur in the coal. In addition, the reductive decomposition of CaSO4 is highlighted. Thesimulation results from the model show that the sulfur contents, the bed temperature, the sorbent particle sizedistribution and the sorbent activity or the maximum conversion rate can significantly influence the sulfuretention performance in circulating fluidized bed (CFB) combustors.``

  5. Refractory experience in circulating fluidized bed combustors, Task 7

    Energy Technology Data Exchange (ETDEWEB)

    Vincent, R.Q.

    1989-11-01

    This report describes the results of an investigation into the status of the design and selection of refractory materials for coal-fueled circulating fluidized-bed combustors. The survey concentrated on operating units in the United States manufactured by six different boiler vendors: Babcock and Wilcox, Combustion Engineering, Foster Wheeler, Keeler Dorr-Oliver, Pyropower, and Riley Stoker. Information was obtained from the boiler vendors, refractory suppliers and installers, and the owners/operators of over forty units. This work is in support of DOE's Clean Coal Technology program, which includes circulating fluidized-bed technology as one of the selected concepts being evaluated.

  6. Effect and surfactants on three-phase fluidized bed hydrodynamics

    International Nuclear Information System (INIS)

    Experiments were conducted to discern the relationship between three-phase fluidized bed hydrodynamics and surfactant solution characteristics. The standard characteristic, equilibrium surface tension, is inadequate. A novel method for surface tension evaluation, a dynamic maximum bubble pressure technique, was found to differentiate the 12 different solutions studied. The surfactant solutions were categorized based upon a combination of the terminal bubble rise velocity reduction, the equilibrium surface tension, and the new bubble tension values. These surfactant solution categories were correlated with experimentally observed three-phase fluidized bed and bubble column hydrodynamic behavior. Specifically, empirical correlations for gas holdup are presented

  7. Carbon Shale Combustion in the Fluidized Bed Reactor

    OpenAIRE

    Olek Małgorzata; Kandefer Stanisław; Kaniowski Wiesław; Żukowski Witold; Baron Jerzy

    2014-01-01

    The purpose of this article is to present the possibilities of coal shale combustion in furnaces with bubbling fluidized bed. Coal shale can be autothermally combusted in the fluidized bed, despite the low calorie value and high ash content of fuel. Established concentrations of CO (500 ppm) and VOC (30 mg/m3) have indicated a high conversion degree of combustible material during combustion process. Average concentrations of SO2 and NOx in the flue gas were higher than this received from the ...

  8. Atmospheric fluidized bed coal combustion research, development and application

    CERN Document Server

    Valk, M

    1994-01-01

    The use of fluidized bed coal combustion technology has been developed in the past decade in The Netherlands with a view to expanding the industrial use of coal as an energy supply. Various research groups from universities, institutes for applied science and from boiler industries participated and contributed to this research area. Comprehensive results of such recent experimentation and development work on atmospheric fluidized bed combustion of coal are covered in this volume. Each chapter, written by an expert, treats one specific subject and gives both the theoretical background as well a

  9. Fluidized bed combustion (citations from the American Petroleum Institute data base). Report for 1964-Jan 79

    Energy Technology Data Exchange (ETDEWEB)

    Cavagnaro, D.M.

    1980-04-01

    These citations from the American Petroleum Institute pertain to fluidized bed processes and processors for the combustion of oil, coal, natural gas, and industrial and municipal wastes. They also discuss air pollution control by fluidized bed combustion, sludge incineration, fluidized bed boilers and furnaces, and design of the fluidized bed combustors. (This updated bibliography contain 108 abstracts, 9 of which are new entries to the previous edition.)

  10. An experimental study of the effect of collision properties on spout fluidized bed dynamics

    NARCIS (Netherlands)

    Buijtenen, van Maureen S.; Börner, Matthias; Deen, Niels G.; Heinrich, Stefan; Antonyuk, Sergiy; Kuipers, J.A.M.

    2009-01-01

    In this paper we experimentally study the effect of collision properties of different particle systems on the bed dynamics of a spout fluidized bed. This is done in different flow regimes: the spout-fluidization regime (case A), the jet-in-fluidized-bed regime (case B) and the spouting-with-aeration

  11. Biofilm detachment mechanisms in a liquid-fluidized bed.

    Science.gov (United States)

    Chang, H T; Rittmann, B E; Amar, D; Heim, R; Ehlinger, O; Lesty, Y

    1991-08-20

    Bed fluidization offers the possibility of gaining the advantages of fixed-film biological processes without the disadvantage of pore clogging. However, the biofilm detachment rate, due to hydrodynamics and particle-to-particle attrition, is very poorly understood for fluidized-bed biofilm processes. In this work, a two-phase fluidized-bed biofilm was operated under a constant surface loading (0.09 mg total organic carbon/cm(2) day) and with a range of bed height (H), fluid velocities (U), and support-particle concentrations (C(p)). Direct measurements were made for the specific biofilm loss rate coefficient (b(s))and the total biofilm accumulation (X(f)L(f)). A hydrodynamic model allowed independent determination of the biofilm density (X(f)), biofilm thickness (L(f)), liquid shear stress (tau), and Reynolds number (Re). Multiple regression analysis of the results showed that increased particle-to-particle attrition, proportional to C(p) and increased turbulence, described by Re, caused the biofilms to be denser and thinner. The specific detachment rate coefficient (b(s)) increased as C(p) and Re increased. Almost all of the 6, values were larger than predicted by a previous model derived for smooth biofilms on a nonfluidized surface. Therefore, the turbulence and attrition of bed fluidization appear to be dominant detachment mechanisms.

  12. DESIGN AND APPLICATION OF FLUIDIZED BED PHOTOCATALYTIC REACTOR

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    @@Photocatalytic degradation of organic pollutant is a new and potential method to transform it to harmless inorganic material, such as CO2 and H2O. So far, most of photocatalytic reactors were cylinder or tabulate photoreactor. The relevant photocatalyst was TiO2 nanometer powder. Although a few investigators had aimed their research field to fluidized bed reactor, their reaction systems were of biphase, such as solid-liquid or solid-gas. Few people focused their research on the triphasic fluidized bed photocatalytic reactor[1]. Compared with traditional photoreactors, a triphasic fluidized bed photoreactor has more advantages[2]: (1) The solid photocatalyst can be separated easily. (2) Its configuration meets the requirement of higher surface area-to-volume ratio of photocatalytic, which is much lower in a fixed bed or a plate photoreactor. (3) The UV light can be used more efficiently. (4) The mass transfer conditions can be controlled and improved easily. (5) It suited to pilot-scale or large-scale operations. For the UV light penetration and photon efficiency should be considered, the photocatalytic reactor differed greatly from a typical fluidized bed reactor.

  13. Modeling results for mass production layering in a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Boehm, K.J., E-mail: kuboehm@gmail.com [Center for Energy Research, M/C 0438 460D EBU II, University of California, San Diego, CA 92093-0438 (United States); Raffray, A.R. [Center for Energy Research, M/C 0438 460D EBU II, University of California, San Diego, CA 92093-0438 (United States); Alexander, N.B.; Goodin, D.T. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States)

    2011-06-15

    A fluidized bed has been proposed as a layering device for the mass production of inertial fusion energy fuel pellets. During this layering process, the frozen deuterium or deuterium-tritium mixture filled into a hollow capsule (about 2-4 mm in diameter) is redistributed leading to a fuel layer of uniform thickness on the inside of the fuel capsule. Several physical processes have been identified to interact with each other to influence the outcome of the layering process in a fluidized bed, which needs to fulfill symmetry requirements of the fuel layer thickness, smoothness and surface damage requirements of the outside target surface and must be able to produce a large number of targets (500 000 per day). This work describes the development and use of numerical tools to conduct a trade-off study focusing on the influence of different flow conditions of the fluidizing gas on the total layering time, final layer uniformity and outer surface damage.

  14. Determination of viscosity in recirculating fluidized bed using radioactive tracer

    International Nuclear Information System (INIS)

    The use of radioactive tracer for measuring viscosity is proposed. The methodology relates the terminal velocity of a radioactive sphere in interior of fluid with the viscosity, which can be a fluidized bed or total flow of solids. The arrangement is composed by two γ detectors placed externally and along the bed. Both detectors are coupled by amplifier to electronic clock. The drop time of sphere between two detectors is measured. The bed viscosity two detectors is measured. The bed viscosity is calculated from mathematical correlations of terminal velocity of the sphere. (M.C.K.)

  15. NOx EMISSIONS FROM BUBBLING FLUIDIZED BED COMBUSTION OF LIGNITE COAL

    Directory of Open Access Journals (Sweden)

    Pavel Skopec

    2015-08-01

    Full Text Available This paper presents experimental results of NOx emission measurements for combustion of two kinds of coal in a bubbling fluidized bed combustor. The tested fuels were Czech brown coal (CBC and German young brown coal (GYC. These fuels have different nitrogen contents. The experiments were performed in the pilot scale BFB experimental unit with power output of 500 kW. The influence of several parameters on NOx formation are investigated in this paper. The parameters studied here include the effect of the nitrogen content in the fuel, the effect of the oxygen concentration in the bed, the effect of bed temperature, the effect of air staging, and the effect of fluidization velocity. Significantly different behaviour of the fuels was found. Although GYC has a lower nitrogen content than CBC, it is more reactive and produces higher NOx emissions. The biggest dependence of NOx production for CBC was found for the effects of air staging and fluidization velocity. As the fluidization velocity increases and the amount of secondary air decreases, there is an increase in NOx emissions. The oxygen concentration in the bed has the strongest effect on the NOx production of GYCs. With increasing oxygen concentration, the production of NOx also increases. On the basis of the NOx measurements, the N-NO conversion factor was calculated and the effect of the operating parameters on this conversion factor was investigated.

  16. A numerical model of gas-fluidized beds

    NARCIS (Netherlands)

    Kuipers, J.A.M.; Duin, van K.J.; Beckum, van F.P.H.; Swaaij, van W.P.M.

    1992-01-01

    A first-principles model for gas-fluidized bed based on the so-called "two-fluid model" (TFM) has been developed. In the TFM approach, both phases are considered to be continuous and fully interpenetrating. The equations of mass, momentum and thermal energy conservation, supplemented with the necess

  17. The porosity in a fluidized bed heat transfer model

    NARCIS (Netherlands)

    Visser, G.; Valk, M.

    1993-01-01

    A mathematical model of heat transfer between a fluidized bed and an immersed surface and a model of gas flow and porosity, both recently published, were combined and further modified in the area of low velocities where the particle convective component of heat transfer is low or neglectable. Experi

  18. Autothermal gasification of low-grade fuels in fluidized bed

    Science.gov (United States)

    Belyaev, A. A.

    2009-01-01

    Autothermal gasification of high-ash floatation wastes of Grade Zh Kuzbass coal and low-ash fuel in a suspended-spouted (fluidized) bed at atmospheric pressure is investigated, and a comparison is presented of experimental results that indicate that the ash content of fuels has only slight influence on the generator gas heating value.

  19. Autothermal gasification of low-grade fuels in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    A.A. Belyaev [Scientific Center for Comprehensive Processing of Solid Combustible Minerals (IGI), Moscow (Russian Federation). Institute of Combustible Minerals Federal State Unitary Enterprise

    2009-01-15

    Autothermal gasification of high-ash flotation wastes of Grade Zh Kuzbass coal and low-ash fuel in a suspended-spouted (fluidized) bed at atmospheric pressure is investigated, and a comparison is presented of experimental results that indicate that the ash content of fuels has only slight influence on the generator gas heating value.

  20. Calcium phosphate precipitation in a fluidized bed. Doctoral thesis

    Energy Technology Data Exchange (ETDEWEB)

    Seckler, M.M.

    1994-01-01

    The objectives of this thesis are: (1) to gain insight into the fundamental processes occurring in a fluidized bed for phosphorus removal from wastewater; (2) to optimize the phosphorus removal efficiency; and (3) to find ways of minimizing the deterimental effect of impurities normally present in wastewaters.

  1. The heat transfer mechanisms in fluidized beds; Laemmoensiirtomekanismit leijukerroksessa

    Energy Technology Data Exchange (ETDEWEB)

    Fogelholm, C.J.; Blomster, A.M.; Kojola, H. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Energy Technology and Environmental Protection

    1997-10-01

    The goal of the research project is to improve the accuracy of the heat transfer correlation in circulating fluidized beds and to define how the heat transfer is distributed in radiation and convection in the different parts of the fluidized bed. This will be carried out by studying the behaviour and the heat transfer of the fluidized bed in the boundary layer near the wall. During the project the concentration and the velocity of the sand particles are measured. The particle concentration and the particle velocity are measured by an image analysis system. A video camera and a Super VHS recorder are used to capture live images from the bed. The images are digitized and stored on a PC. The measured particle concentration was at highest slightly over 20 % on the straight wall. As expected, the velocity of the fluidizing gas had the most important role on the particle concentration. The experimental studies of the particle velocity were started last autumn 1996. The velocities of the particles were measured by using a multiple exposure technique. Afterwards the images captured were analyzed by performing a Fourier transform analysis. So far the results have been encouraging and the analyzing work will be ended this spring. (orig.)

  2. Nitrogen Chemistry in Fluidized Bed Combustion of Coal

    DEFF Research Database (Denmark)

    Jensen, Anker Degn

    for the emission of NOx from FBC has been developed as part of a JOULE project. The model is based on the two-phase theory of fluidization for the bed with a Kunii-Levenspiel type freeboard model and includes submodels for coal devolatilization, combustion of volatiles and char and a detailed model of NO formation...

  3. Description of emission control using fluidized-bed, heat-exchange technology

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, G.J.; Grogan, P.J.

    1980-06-01

    Environmental effects of fluidized-bed, waste-heat recovery technology are identified. The report focuses on a particular configuration of fluidized-bed, heat-exchange technology for a hypothetical industrial application. The application is a lead smelter where a fluidized-bed, waste-heat boiler (FBWHB) is used to control environmental pollutants and to produce steam for process use. Basic thermodynamic and kinetic information for the major sulfur dioxide (SO/sub 2/) and NO/sub x/ removal processes is presented and their application to fluidized-bed, waste heat recovery technology is discussed. Particulate control in fluidized-bed heat exchangers is also discussed.

  4. Investigation on Side-Spray Fluidized Bed Granulation with Swirling Airflow

    OpenAIRE

    Wong, Poh Mun; Chan, Lai Wah; Heng, Paul Wan Sia

    2012-01-01

    Top-spray fluidized bed granulation with axial fluidization airflow from the bottom of the granulator is well-established in the pharmaceutical industry. The application of swirling airflow for fluidized bed granulation was more recently introduced. This study examined the effects of various process parameters on the granules produced by side-spray fluidized bed with swirling airflow using the central composite and Box–Behnken design of experiment. Influence of the amount of binder solution, ...

  5. Hydrodynamics of gas-solids downflow fluidized bed (downer) reactor

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H.

    1999-07-01

    This study presents a semi-empirical model for the hydrodynamic flow structure in a circulating fluidized bed downer reactor. Circulating fluidized bed, or riser reactors are used in the petroleum industry for many applications including catalytic cracking, polyethylene production, calcination operations and combustion of a variety of fuels. The work in this thesis involved the development of a circulating fluidized bed riser and downer system that enables hydrodynamic studies to be carried out. The system was designed to incorporate both a riser and a downer in the same circulating operation, making it possible to conduct experimental studies on the riser and the downer separately or simultaneously. The hydrodynamics of the gas-solids downflow fluidized bed reactor were studied in a 9.3 m tall and 0.1 m i.d. circulating fluidized bed downer reactor using fluidized cracking catalyst (FCC) particles. In order to characterize the gas-solids flow structures, the following three parameters were measured: the radial distributions of the local solids holdups, the local particle velocities, and the pressure gradients along the downer column. The hydrodynamics in the co-current downflow reactor was also studied under a wide range of operating conditions. The gas-solids flow structure under zero superficial gas velocity conditions was characterized by measuring the radial distribution of the local solids holdups and particle velocities along the downer column with the superficial gas velocity set to zero. The results indicate that two basic flow regimes exist in the FCC downer system depending on the superficial gas velocity. The downer reactor was shown to have a more uniform radial flow structure compared to the riser. It also has a more uniform radial distribution of solids holdup and particle velocity as well as solids flux in both the development and fully developed zones. The highly uniform radial flow structure provides a nearly ideal plug flow condition in the

  6. The heat transfer mechanisms in fluidized beds; Laemmoensiirtomekanismit leijukerroksessa

    Energy Technology Data Exchange (ETDEWEB)

    Fogelholm, C.J.; Blomster, A.M.; Kojola, H. [Helsinki Univ. of Technology, Espoo (Finland)

    1996-12-01

    The goal of the research project is to improve the accuracy of the heat transfer correlation in circulating fluidized beds and to define how the heat transfer is distributed in radiation and convection in the different parts of the fluidized bed. This will be carried out by studying the behaviour and heat transfer of the fluidized bed in the boundary layer near the wall. The total and radiative heat transfer as well as the particle concentration will be measured. Based on the data a correlation will be created. Two different measurement systems are used. The particle concentration is measured by a image-analysis system. A video camera and a Super VHS recorder are used to capture live images from the bed. The images are digitized and stored on a PC. The system has been used in previous research projects at our laboratory. In earlier projects all measurements have been carried out in cold environments. In this project the system will be modified for hot environments. The radiative heat transfer is measured by a radiative heat transfer probe connected to a PC via an A/D converter. The probe consists of a heat flow detector which is isolated from the bed by a sapphire window so that only the radiative part of the heat transfer is detected. The probe will be calibrated in a black body oven so that the effect of the conduction and the sapphire window can be separated. (author)

  7. Operation of a fluidized-bed denitrification bioreactor

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, P.A.

    1978-11-15

    In the fluidized-bed denitrification process developed, bacteria are allowed to grow and attach themselves to 0.25 to 0.60-mm-OD coal particles, and nitrate-containing solution is pumped up through the column at a velocity sufficient to fluidize the bacteria-coated coal particles. The denitrification bacteria convert the nitrate ions to nitrogen gas. A 10-cm-ID column has been operated by Oak Ridge Y-12 Plant personnel to test the scale-up and operational characteristics of the fluidized bed process. The reactor consists of a tapered bottom section for flow distribution, several straight 10-cm-ID cylindrical sections, and a tapered top section for solid/liquid disengaging. Increasing the diameter of the reactor by a factor of two did not cause any decrease in reactor performance. The fluidized-bed reactor is characterized by short-residence-time requirements (about 2 minutes per meter of height), and by high, but variable, denitrification rates (2 to 35 g NO/sub 3//sup -/-N/dm/sup 3//day). The reactor is best suited for relatively low-concentration nitrate wastes (<1 wt% NO/sub 3//sup -/). The economics of using the reactor for high-concentration wastes (>20 wt% NO/sub 3//sup -/) is less favorable, but still may be competitive with other reactor types. 9 figs, 2 tables.

  8. Chlorination of commercial molybdenite concentrate in a fluidized bed reactor

    Science.gov (United States)

    Nair, K. U.; Sathiyamoorthy, D.; Bose, D. K.; Sundaresan, M.; Gupta, C. K.

    1987-06-01

    Studies on recovery of molybdenum from commercial grade molybdenite using the technique of fluidized bed chlorination in the presence of oxygen are presented. Molybdenum recovery above 99 pct at a chlorine utilization efficiency of 84 pct has been achieved for a fluidizing gas flow-rate of 3 L/min of the gases Cl2, O2, and N2 mixed in the proportion of 2∶5∶23, respectively, at 300 °C. The investigations on kinetics showed that the overall oxychlorination reaction is controlled by chemical reaction and is of first order with respect to particle surface area.

  9. Theoretical comparison of packed bed and fluidized bed membrane reactors for methane reforming

    NARCIS (Netherlands)

    Gallucci, Fausto; Sint Annaland, van Martin; Kuipers, J.A.M.

    2010-01-01

    In this theoretical work the performance of different membrane reactor concepts, both fluidized bed and packed bed membrane reactors, has been compared for ultra-pure hydrogen production via methane reforming. Using detailed theoretical models, the required membrane area to reach a given conversion

  10. Fluidized-bed and packed-bed characteristics of gel beads

    NARCIS (Netherlands)

    Zessen, van E.; Tramper, J.; Rinzema, A.; Beeftink, H.H.

    2005-01-01

    A liquid-fluidized bed or packed bed with gel beads is attractive as an immobilized-cell bioreactor. The performance of such bioreactors is influenced by the physical behavior of these beads. Three different but related aspects involving the drag force between particles and liquid were studied for f

  11. EFFECT OF VERTICAL BAFFLES ON PARTICLE MIXING AND DRYING IN FLUIDIZED BEDS OF GROUP D PARTICLES

    Institute of Scientific and Technical Information of China (English)

    Chung Lim Law; Siti Masrinda Tasirin; Wan Ramli Wan Daud; Derek Geldart

    2003-01-01

    This study reports the effect of vertical baffles on the group D powder mixing and drying characteristics in a batch fluidized bed dryer. Results obtained in this study showed that operating the fluidized bed dryer with vertical baffles gave better particle mixing. This is due to the fact that the vertical baffles acted to limit the growth of small bubbles into large bubbles and the small bubbles caused more vigorous mixing in the bed of particles before finally erupting at the bed surface. Thus, insertion of vertical baffles is a useful way to process group D particles in a fluidized bed, especially when the fluidized bed is large.

  12. Plasma spouted/fluidized bed for materials processing

    Science.gov (United States)

    Sathiyamoorthy, D.

    2010-02-01

    Plasma when coupled with spout/fluidized bed reactor for gas-solid reaction brings in several advantages such as high rate of heat and mass transfer, generation of high bulk temperature using a thin jet of plasma itself as a heat source. The science and technology of plasma and fluidization or spouted bed are well established except of these two put together for high temperature application. Plasma heating of fluid/ spouted bed can bring down the size of the equipment and increase the productivity. However the theory and practice of the hybrid technology has not been tested in a variety of applications that involves high temperature synthesis of materials, TRISO particle coating for nuclear fuel particle, thermal decomposition of refractory type ore, halogenations of minerals, particulate processes and synthesis of advanced materials. This paper gives an account of the use and exploitation of plasma coupled with spouted/ fluidized bed especially for material processing and also addresses the issues for adapting the same in the era of developing advanced high temperature materials.

  13. Thermal modeling of microwave heated packed and fluidized bed catalytic reactors.

    Science.gov (United States)

    Thomas, J R; Faucher, F

    2000-01-01

    Thermal models of small-scale, microwave-heated, packed-bed and fluidized-bed catalytic chemical reactors were developed to investigate the possibility of selectively heating the catalyst sites or the catalyst pellets with microwaves. Results indicate catalyst sites may be selectively heated under special conditions in a packed or fluidized bed, and catalyst pellets may be heated above the temperature of the cooling(and reacting) gas under certain conditions in a fluidized bed. PMID:11098441

  14. Bubbles trapped in a fluidized bed: Trajectories and contact area

    Science.gov (United States)

    Poryles, Raphaël; Vidal, Valérie; Varas, Germán

    2016-03-01

    This work investigates the dynamics of bubbles in a confined, immersed granular layer submitted to an ascending gas flow. In the stationary regime, a central fluidized zone of parabolic shape is observed, and the bubbles follow different dynamics: either the bubbles are initially formed outside the fluidized zone and do not exhibit any significant motion over the experimental time or they are located inside the fluidized bed, where they are entrained downwards and are, finally, captured by the central air channel. The dependence of the air volume trapped inside the fluidized zone, the bubble size, and the three-phase contact area on the gas injection flow rate and grain diameter are quantified. We find that the volume fraction of air trapped inside the fluidized region is roughly constant and of the order of 2%-3% when the gas flow rate and the grain size are varied. Contrary to intuition, the gas-liquid-solid contact area, normalized by the air injected into the system, decreases when the flow rate is increased, which may have significant importance in industrial applications.

  15. Mixing equilibrium in two-density fluidized beds by DEM

    Science.gov (United States)

    Di Renzo, A.; Di Maio, F. P.

    2010-05-01

    Interaction of fluid and granular flows in dense two-phase systems is responsible for the significantly different behavior of units used in the chemical industry such as fluidized beds. The momentum exchange phenomena involved during gas fluidization of a binary mixture of solids differing in density is such that the continuous mixing action of the fluid flowing upwards counteracts the natural tendency of the two (fluidized) solids to segregate with the heavier component fully settling at the bottom of the bed. In the present work the complex hydrodynamics of two-density gas-fluidized beds is studied by means of a DEM-CFD computational approach, combining the discrete element method (DEM) and a solution of the locally averaged equations of motion (CFD). The model is first validated against experimental data and then used to investigate the role of gas velocity versus density ratio of the two components in determining the distribution of the components in the system. It is shown first that a unique equilibrium composition profile is reached independent of the initial arrangements of the solids. Then, numerical simulations are used to find the equilibrium conditions of mixing/segregation as a function of the gas velocity in excess of the minimum fluidization velocity of the heavier component and as a function of the density ratio of the two solid species. A mixing map on the gas velocity-density ratio plane is finally reconstructed by plotting iso-mixing lines that shows quantitatively how conditions ranging from full mixing to fully segregated components are obtained.

  16. Fluidized bed roasting of molybdenite-effect of operating variables

    Energy Technology Data Exchange (ETDEWEB)

    Doheim, M.A.; Abdel-Wahab, M.Z.; Rassoul, S.A.

    1976-09-01

    The results of an investigation on the fluidized bed roasting of molybdenite are reported. Molybdenite mixed with quartz was subjected to an oxidizing roast in a 22 mm diam stainless steel batch fluidized bed reactor. Enriched air (with O/sub 2/) or diluted air (with N/sub 2/) was used as the fluidizing and oxidizing gas. In addition to the MoS/sub 2/ content of the solids and the O/sub 2/ content of the gas, the effect of temperature and flow rate was also examined. For the range of variables investigated, it was found that the temperature influences the rate of the roasting reaction greatly. The gas flow rate affects the conversion favorably up to a certain fluidizing flow rate. An increase in the O/sub 2/ content of the gas and the MoS/sub 2/ of the solids results in higher conversion levels. The unreacted core kinetic model was applied to the results; and the energy of activation for the reaction was obtained from the Arrhenius plot as 31,100 cal/gmol of MoS/sub 2/. The data obtained should be useful in the design and operation of larger scale roasting reactors.

  17. Fluidized bed roasting of molybdenite-effect of operating variables

    International Nuclear Information System (INIS)

    The results of an investigation on the fluidized bed roasting of molybdenite are reported. Molybdenite mixed with quartz was subjected to an oxidizing roast in a 22 mm diam stainless steel batch fluidized bed reactor. Enriched air (with O2) or diluted air (with N2) was used as the fluidizing and oxidizing gas. In addition to the MoS2 content of the solids and the O2 content of the gas, the effect of temperature and flow rate was also examined. For the range of variables investigated, it was found that the temperature influences the rate of the roasting reaction greatly. The gas flow rate affects the conversion favorably up to a certain fluidizing flow rate. An increase in the O2 content of the gas and the MoS2 of the solids results in higher conversion levels. The unreacted core kinetic model was applied to the results; and the energy of activation for the reaction was obtained from the Arrhenius plot as 31,100 cal/gmol of MoS2. The data obtained should be useful in the design and operation of larger scale roasting reactors

  18. The effect of vibration on bed voidage behaviors in fluidized beds with large particles

    Directory of Open Access Journals (Sweden)

    H. Jin

    2007-09-01

    Full Text Available The effects of vibration parameters, operating conditions and material properties on bed voidage were investigated using an optical fiber probe approach in a vibrating fluidized bed with a diameter of 148 mm. Variables studied included frequency (0-282 s-1, amplitude (0 mm-1 mm, bed height (0.1 m-0.4 m as well as four kinds of particles (belonging to Geldart's B and D groups. The axial and radial voidage distribution with vibration is compared with that without vibration, which shows vibration can aid in the fluidization behaviors of particles. For a larger vibration amplitude, the vibration seriously affects bed voidage. The vibration energy can damp out for particle layers with increasing the bed height. According to analysis of experimental data, an empirical correlation for predicting bed voidage, giving good agreement with the experimental data and a deviation within ±15%, was proposed.

  19. The effect of vibration on bed voidage behaviors in fluidized beds with large particles

    Energy Technology Data Exchange (ETDEWEB)

    Jin, H.; Zhang, J.; Zhang, B.

    2007-07-01

    The effects of vibration parameters, operating conditions and material properties on bed voidage were investigated using an optical fiber probe approach in a vibrating fluidized bed with a diameter of 148 mm. Variables studied included frequency (0-282 s{sup -1}), amplitude (0 mm-1 mm), bed height (0.1 m-0.4 m) as well as four kinds of particles (belonging to Geldart's B and D groups). The axial and radial voidage distribution with vibration is compared with that without vibration, which shows vibration can aid in the fluidization behaviors of particles. For a larger vibration amplitude, the vibration seriously affects bed voidage. The vibration energy can damp out for particle layers with increasing the bed height. According to analysis of experimental data, an empirical correlation for predicting bed voidage, giving good agreement with the experimental data and a deviation within {+-}15%, was proposed. 20 refs., 8 figs., 2 tabs.

  20. Defluidization in fluidized bed gasifiers using high-alkali content fuels

    DEFF Research Database (Denmark)

    Narayan, Vikas; Jensen, Peter Arendt; Henriksen, Ulrik Birk;

    2016-01-01

    major concern in thermal conversion of biomass encountered in fluidized beds is bed agglomeration, which may result in de-fluidization, leading to unscheduled downtime and additional costs. Biomass fuels, especially herbaceous plants, often contain significant amounts of silicon, potassium...... and calcium, which may form viscous melts that adhere on the surface of the colliding bed particles and bind them to form agglomerates. In this paper, studies were made to understand the behavior of inorganic elements (mainly K, Si and Ca) on agglomeration and de-fluidization of alkali rich bed......-material samples undernon-oxidizing conditions in a bench-scale fluidized bed reactor set up. The de-fluidization studies involved measurements with sand and pure potassium salts (KCl and K2CO3) as well as with bed material samples obtained from a 6 MW Low Temperature Circulating Fluidized Bed (LTCFB) gasifier...

  1. Particle-scale simulation of fluidized bed with immersed tubes

    Institute of Scientific and Technical Information of China (English)

    Yongzhi ZHAO; Maoqiang JIANG; Yi CHENG

    2008-01-01

    In order to simulate gas-solids flows with complex geometry,the boundary element method was incorporated into the implementation of a combined model of computational fluid dynamics and discrete element method.The resulting method was employed to simulate hydrodynamics in a fluidized bed with immersed tubes.The transient simulation results showed particle and bubble dynamics.The bubble coalescence and break-up behavior when passing the immersed tubes was successfully predicted.The gas-solid flow pattern in the fluidized bed is changed greatly because of the immersed tubes.As particles and gas are come in contact with the immersed tubes,the gas bubbles will be deformed.The collisions between particles arid tubes will make the tubes sur-rounded by air pockets most of the time and this is unfavorable for the heat transfer between particles and tubes.

  2. Autothermal fluidized bed pyrolysis of Cuban pine sawdust

    Energy Technology Data Exchange (ETDEWEB)

    Suarez, J.; Beaton, P. [University of the Orient, Santiago de Cuba (Cuba). Faculty of Mechanical Engineering; Zanzi, R.; Grimm, A. [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    2006-06-15

    Oxidative pyrolysis of Cuban pine sawdust was investigated using an autothermal fluidized bed reactor. Biomass particles were fed continuously (8.13 Kg/h) in a bed, fluidized by air gas. Experiments were conduced at three different dimensionless air factors 1, 1.5, and 2 (defined as ratio of actual air flow rate to stoichiometric air flow rate). The various physical and chemical characteristics of the pyrolysis products acquired in these conditions were identified. The results indicated that (1) the operating temperature can be correlated with the air factor; (2) the higher air factor promotes high temperature and contributes to the secondary reactions, which lead to less liquid; (3) the physicochemical characterization of the pyrolysis products indicated that the air factor, in the range studied, does not have a notable influence in their properties; (4) the liquid and char products obtained may be a potentially valuable source of chemical feedstocks. (Author)

  3. Circulating fluidized bed coal-saving optimization control method

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Tengfei; Li, Dewei; Xi, Yugeng; Zhou, Wu [Shanghai Jiao Tong Univ., Shanghai (China). Dept. of Automation; Ministry of Education, Shanghai (China). Key Lab. of System Control and Information Processing; Yin, Debin [Shanghai Xinhua Control Technology (Group) Co., Ltd., Shanghai (China)

    2013-07-01

    The circulating fluidized bed boiler is widely used in thermal power plants. With the proposal of energy-saving emission reduction, how to reduce coal consumption while ensure the output steam quality at the same time has become an important topic. This paper combines the technology of RTO (real-time optimization) and zone control in DMC (dynamic matrix control) to achieve this goal. The proposed method adds the coal consumption into the objective function of DMC controller and the operation point of the boiler is permitted to change within a zone which can be set according to the actual requirements of the circulating fluidized bed boiler. The zone control in DMC provides the freedom to reduce the coal consumption and achieves the economic optimal target. Compared to the simple use of constrained DMC control, the proposed method is verified to be remarkable coal-saving by the case study of a 150 t/h boiler of a power plant in Sichuan.

  4. Combustion of Jordanian oil shale using circulating fluidized bed

    International Nuclear Information System (INIS)

    this study re[resents design and manufacturing of a lab-scale circulating fluidized bed (C.F.B) to burn low grade fuel such as Jordanian oil shale. Hydrodynamic properties of C.F.B. were studied like minimum fluidization velocity, circulation flux and carryover rate. a hot run was firstly conducted by the combustion of L.P.G. to start up the combustion process. It proceeds until reaching the minimum burning temperature of oil shale particles, at which time the LPG supply was gradually reduced and oil shale feeding started. soon after reaching a self sustainable condition of oil shale particles, the LPG supply was cut off. The main combustion variables were investigated such as air to fuel ratios, temperature profiles across the bed, exhaust gas analysis and combustion efficiency. a combustion intensity of 859 kg/hr.m2 and combustion efficiency of 96% were achieved. (authors). 19 refs., 9 tab., 18 fig

  5. Heat transfer characteristics of the fluidized bed through the annulus

    Science.gov (United States)

    Shedid, Mohamed H.; Hassan, M. A. M.

    2016-09-01

    The annular fluidized bed can be regarded as a promising technique for waste heat recovery applications. This study investigates on the determination of steady state values of the average heat transfer on the surface of the inner tube under different operating conditions that include: (1) input heat flux ranging from 557 to 1671 W/m2, (2) superficial air velocity ranging between 0.12 and 0.36 m/s, (3) initial bed height ranging from 25 to 55 cm, (4) ratio of the inner to the outer diameters ranging from 1/6 to 1/2 and Kaolin particle diameters ranging between 282 and 550 µm. The average values of the heat transfer coefficient along the inner tube (consisting of the fluidized and free board sections) are also deduced. An empirical correlation for calculating the Nusselt number is obtained for the given parameters and ranges.

  6. Heat transfer characteristics of the fluidized bed through the annulus

    Science.gov (United States)

    Shedid, Mohamed H.; Hassan, M. A. M.

    2015-11-01

    The annular fluidized bed can be regarded as a promising technique for waste heat recovery applications. This study investigates on the determination of steady state values of the average heat transfer on the surface of the inner tube under different operating conditions that include: (1) input heat flux ranging from 557 to 1671 W/m2, (2) superficial air velocity ranging between 0.12 and 0.36 m/s, (3) initial bed height ranging from 25 to 55 cm, (4) ratio of the inner to the outer diameters ranging from 1/6 to 1/2 and Kaolin particle diameters ranging between 282 and 550 µm. The average values of the heat transfer coefficient along the inner tube (consisting of the fluidized and free board sections) are also deduced. An empirical correlation for calculating the Nusselt number is obtained for the given parameters and ranges.

  7. Carbon Shale Combustion in the Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    Olek Małgorzata

    2014-06-01

    Full Text Available The purpose of this article is to present the possibilities of coal shale combustion in furnaces with bubbling fluidized bed. Coal shale can be autothermally combusted in the fluidized bed, despite the low calorie value and high ash content of fuel. Established concentrations of CO (500 ppm and VOC (30 mg/m3 have indicated a high conversion degree of combustible material during combustion process. Average concentrations of SO2 and NOx in the flue gas were higher than this received from the combustion of high quality hard coal, 600 ppm and 500 ppm, respectively. Optional reduction of SO2 and NOx emission may require the installation of flue gas desulphurization and de-NOx systems.

  8. Experiments and Modelling of Coal Pyrolysis under Fluidized Bed Conditions

    Institute of Scientific and Technical Information of China (English)

    ZhangYongzhe; XuXiangdong; 等

    1999-01-01

    The pyrolysis behavior of two Chinese coals has been investigated in a laboratory-scale bubbling fluidized bed system in Siegen University,Germany,Experimental equipment and procedure are introduced.The amounts of pyrolysis species of each coal were measured,calcuated and compared.A new method was presented to determine the needed parameters in FG-DVC model with the experimental results instead of other much more complicated experiments.

  9. Water desalination by a fluidized bed nuclear reactor

    International Nuclear Information System (INIS)

    The great need for potable water in the world motivated the International Atomic Energy Agency (IAEA) to study the feasibility of nuclear seawater desalination. The consensus reached is that nuclear desalination is technically feasible, though cost and social acceptability are recognized as major problems to overcome. Here an inherently safe reactor with reduced cost is proposed to overcome these barriers. The reactor is a simple small modular nuclear reactor based on fluidized bed concept with passive cooling characteristics. (orig.)

  10. The grinding of uranium dioxide from fluidized beds

    International Nuclear Information System (INIS)

    This work deals with the UO2 vibratory grinding, the UO2 obtained from fluidized beds. In this study the grinding time has been correlated with surface area, stoichiometry, granulometry and grinded product contamination. The efficiency losses in the grinding of moisten UO2 are outlined. Finally it is made a brief study of the granulate obtained from the grinded UO2 as well as the green pellets resulting from it, taking into consideration the dispersion of its density and height. (Author)

  11. Fluidized bed control system based on inverse system method

    Institute of Scientific and Technical Information of China (English)

    SONG Fu-hua; LI Ping

    2005-01-01

    The invertible of the Large Air Dense Medium Fluidized Bed (ADMFB) were studied by introducing the concept of the inverse system theory of nonlinear systems.Then the ADMFB, which was a multivariable, nonlinear and coupled strongly system,was decoupled into independent SISO pseudo-linear subsystems. Linear controllers were designed for each of subsystems based on linear systems theory. The practice output proves that this method improves the stability of the ADMFB obviously.

  12. Chemical looping combustion of coal in interconnected fluidized beds

    Institute of Scientific and Technical Information of China (English)

    SHEN LaiHong; ZHENG Min; XIAO Jun; ZHANG Hui; XIAO Rui

    2007-01-01

    Chemical looping combustion is the indirect combustion by use of oxygen carrier.It can be used for CO2 capture in power generating processes. In this paper,chemical looping combustion of coal in interconnected fluidized beds with inherent separation of CO2 is proposed. It consists of a high velocity fluidized bed as an air reactor in which oxygen carrier is oxidized, a cyclone, and a bubbling fluidized bed as a fuel reactor in which oxygen carrier is reduced by direct and indirect reactions with coal. The air reactor is connected to the fuel reactor through the cyclone. To raise the high carbon conversion efficiency and separate oxygen carrier particle from ash, coal slurry instead of coal particle is introduced into the bottom of the bubbling fluidized bed. Coal gasification and the reduction of oxygen carrier with the water gas take place simultaneously in the fuel reactor. The flue gas from the fuel reactor is CO2 and water. Almost pure CO2 could be obtained after the condensation of water. The reduced oxygen carrier is then returned back to the air reactor, where it is oxidized with air. Thermodyanmics analysis indicates that NiO/Ni oxygen carrier is the optimal one for chemical looping combustion of coal.Simulation of the processes for chemical looping combustion of coal, including coal gasification and reduction of oxygen carrier, is carried out with Aspen Plus software. The effects of air reactor temperature, fuel reactor temperature, and ratio of water to coal on the composition of fuel gas, recirculation of oxygen carrier particles, etc., are discussed. Some useful results are achieved. The suitable temperature of air reactor should be between 1050-1150Cand the optimal temperature of the fuel reactor be between 900-950℃.

  13. Chemical looping combustion of coal in interconnected fluidized beds

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Chemical looping combustion is the indirect combustion by use of oxygen carrier. It can be used for CO2 capture in power generating processes. In this paper, chemical looping combustion of coal in interconnected fluidized beds with inherent separation of CO2 is proposed. It consists of a high velocity fluidized bed as an air reactor in which oxygen carrier is oxidized, a cyclone, and a bubbling fluidized bed as a fuel reactor in which oxygen carrier is reduced by direct and indirect reactions with coal. The air reactor is connected to the fuel reactor through the cyclone. To raise the high carbon conversion efficiency and separate oxygen carrier particle from ash, coal slurry instead of coal particle is introduced into the bottom of the bubbling fluidized bed. Coal gasification and the reduction of oxygen carrier with the water gas take place simultaneously in the fuel reactor. The flue gas from the fuel reactor is CO2 and water. Almost pure CO2 could be obtained after the con- densation of water. The reduced oxygen carrier is then returned back to the air reactor, where it is oxidized with air. Thermodyanmics analysis indicates that NiO/Ni oxygen carrier is the optimal one for chemical looping combustion of coal. Simulation of the processes for chemical looping combustion of coal, including coal gasification and reduction of oxygen carrier, is carried out with Aspen Plus software. The effects of air reactor temperature, fuel reactor temperature, and ratio of water to coal on the composition of fuel gas, recirculation of oxygen carrier par- ticles, etc., are discussed. Some useful results are achieved. The suitable tem- perature of air reactor should be between 1050―1150℃and the optimal temperature of the fuel reactor be between 900―950℃.

  14. Gasification of wood in a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, L.C. de; Marti, T.; Frankenhaeuser, M. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

    1997-06-01

    A first series of gasification experiments with our fluidized bed gasifier was performed using clean sawdust as fuel. The installation and the analytical systems were tested in a parametric study in which gasification temperature and equivalence ratio were varied. The data acquired will serve to establish the differences between the gasification of clean wood and the gasification of Altholz (scrapwood) and wood/plastics mixtures. (author) 1 fig., 3 tabs., 5 refs.

  15. CFD-DEM study of effect of bed thickness for bubbling fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Tingwen, Li; Gopalakrishnan, Pradeep; Garg, Rahul; Shahnam, Mehrdad

    2011-10-01

    The effect of bed thickness in rectangular fluidized beds is investigated through the CFD–DEM simulations of small-scale systems. Numerical results are compared for bubbling fluidized beds of various bed thicknesses with respect to particle packing, bed expansion, bubble behavior, solids velocities, and particle kinetic energy. Good two-dimensional (2D) flow behavior is observed in the bed having a thickness of up to 20 particle diameters. However, a strong three-dimensional (3D) flow behavior is observed in beds with a thickness of 40 particle diameters, indicating the transition from 2D flow to 3D flow within the range of 20–40 particle diameters. Comparison of velocity profiles near the walls and at the center of the bed shows significant impact of the front and back walls on the flow hydrodynamics of pseudo-2D fluidized beds. Hence, for quantitative comparison with experiments in pseudo-2D columns, the effect of walls has to be accounted for in numerical simulations.

  16. CFD-DEM study of effect of bed thickness for bubbling fluidized beds

    Institute of Scientific and Technical Information of China (English)

    Tingwen Li; Pradeep Gopalakrishnana; Rahul Garg; Mehrdad Shahnam

    2012-01-01

    The effect of bed thickness in rectangular fluidized beds is investigated through the CFD-DEM simulations of small-scale systems.Numerical results are compared for bubbling fluidized beds of various bed thicknesses with respect to particle packing,bed expansion,bubble behavior,solids velocities,and particle kinetic energy.Good two-dimensional (2D) flow behavior is observed in the bed having a thickness of up to 20 particle diameters.However,a strong three-dimensional (3D) flow behavior is observed in beds with a thickness of 40 particle diameters,indicating the transition from 2D flow to 3D flow within the range of 20-40 particle diameters.Comparison of velocity profiles near the walls and at the center of the bed shows significant impact of the front and back walls on the flow hydrodynamics of pseudo-2D fluidized beds.Hence,for quantitative comparison with experiments in pseudo-2D columns,the effect of wails has to be accounted for in numerical simulations.

  17. Fluidized and vibrofluidized shallow beds of fresh leaves

    Institute of Scientific and Technical Information of China (English)

    Renata de Aquino Brito Lima; Maria do Carmo Ferreira

    2011-01-01

    The fluid dynamics behavior of shallow fluidized and vibrofluidized beds operating with fresh leaves was investigated with the aim of exploring drying applications in a modified conveyor belt (MCB) system, which may be operated in a fixed- or fiuidized-bed mode. Leaves of the specimens Duranta repens,Schinus molle, Coleus barbatus, Buxus sempervirens, and Bougainvillea spectabilis were tested with a range of sphericities from 0.063 to 0.213. bulk densities from 0.038 to 0.251 g/cm3. apparent densities from 0.52 to 0.97 g/cm3 and ratios of total surface area to volume from 21 to 224 cm-t. Fluidization characteristic curves were obtained by measuring pressure drops versus air velocity in a rectangular column of 0.20m x 0.11 m cross section. It was not possible to reach real fluidized regimes with the leaves due to strongly non-homogeneous beds. Nevertheless, the characteristic curves allowed for the identification of a transition regime from fixed- to expanded-beds, and parameters such as air velocity and pressure drop obtained from the experimental data at the transition were reproducible for specimens with lower surface area or lower specific gravity (i.e., Duranta repens, Schinus molle, and Bougainvillea spectabilis).The transition velocity and pressure drop could not be predicted by the literature developed for estimat0.5 and 1.0 helped to reduce channeling and decrease the transition velocities from fixed to expanded regimes although it did not affect the pressure drops after the bed expansion. The results suggest that drying fresh leaves using the MCB dryer operating in a fluidized mode would not be feasible because none of the materials investigated attained a high-quality fluidization. Operation of the MCB dryer may be possible by alternating between the fixed and vibrofluidized modes. For the specimens tested, the drying should be performed in a range of air velocities from 0.50 to 0.60 m/s to ensure that the operation is in a vibrofluidized regime. The

  18. Fluidized bed dip coated silicon carbide on graphite

    International Nuclear Information System (INIS)

    Silicon carbide (SiC) coatings hold great promise in high temperature applications by virtue of their excellent physical and chemical properties. They are produced by techniques ranging from chemical vapor deposition to reaction bonding by melt infiltration. Reaction bonded SiC finds importance in nuclear applications as high temperature, thermally conducting coatings with good abrasion resistance. Additionally, they also possess the ability to withstand high neutron fluence, and thereby find importance as a protective layer in the graphite fuel tubes used in the compact high temperature reactor. The current work explores the deposition of SiC on graphite cylinders by dip-coating a heated graphite rod in a fluidized bed of silicon. The solid state reaction of silicon and carbon under vacuum/inert atmosphere and elevated temperatures is explored. A novel idea of immersing a heated graphite sample in a bed of fluidized silicon powder is presented. The graphite sample is heated to 1450-1550 deg C prior to dipping in the fluidized bed of silicon. The technique presents advantages of quick heating and lower deposition times, and reasonably uniform coatings. Importantly, the setup does not require effluent treatment nor does it involve the use of corrosive precursors leading to higher operational safety as opposed to other vapor deposition methods. The method is well adapted for three-dimensional surfaces as well. Initial experimental results are presented along with the design details of the perforated distributor plate for the coating unit, and the feasibility of the technique is explored. (author)

  19. Influence of rolling friction on single spout fluidized bed simulation

    Institute of Scientific and Technical Information of China (English)

    Christoph Goniva; Christoph Kloss; Niels G. Deen; Johannes A. M. Kuipers; Stefan Pirker

    2012-01-01

    In this paper we study the effect of rolling friction on the dynamics in a single spout fluidized bed using Discrete Element Method (DEM) coupled to Computational Fluid Dynamics (CFD).In a first step we neglect rolling friction and show that the results delivered by the open source CFD-DEM framework applied in this study agree with previous simulations documented in literature.In a second step we include a rolling friction sub-model in order to investigate the effect of particle non-sphericity.The influence of particle-particle as well as particle-wall rolling friction on the flow in single spout fluidized bed is studied separately.Adequate rolling friction model parameters are obtained using first principle DEM simulations and data from literature.Finally,we demonstrate the importance of correct modelling of rolling friction for coupled CFD-DEM simulations of spout fluidized beds.We show that simulation results can be improved significantly when applying a rolling friction model,and that experimental data from literature obtained with Positron Emission Particle Tracking (PEPT) technique can be satisfactorily reproduced.

  20. Prediction of product distribution in fine biomass pyrolysis in fluidized beds based on proximate analysis.

    Science.gov (United States)

    Kim, Sung Won

    2015-01-01

    A predictive model was satisfactorily developed to describe the general trends of product distribution in fluidized beds of lignocellulosic biomass pyrolysis. The model was made of mass balance based on proximate analysis and an empirical relationship with operating parameters including fluidization hydrodynamics. The empirical relationships between product yields and fluidization conditions in fluidized bed pyrolyzers were derived from the data of this study and literature. The gas and char yields showed strong functions of temperature and vapor residence time in the pyrolyzer. The yields showed a good correlation with fluidization variables related with hydrodynamics and bed mixing. The predicted product yields based on the model well accorded well with the experimental data.

  1. Phase-Plane Invariant Analysis of Pressure Fluctuations in Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    WANG Xiaoliang; HE Rong; Toshiyuki Suda; Junichi Sato

    2007-01-01

    Partial agglomeration is a major problem in fluidized beds. A chaotic analytical method based on the phase-plane invariant of the pressure fluctuations in the fluidized beds has been used to warn of agglomeration at an early stage. Cold tests (no combustion) and hot tests (combustion) in fluidized beds show that the phase-plane invariant of the pressure fluctuations can distinguish the dynamic behavior of fluidized beds with different flow rates in cold tests. With combustion, when the flow rate was kept constant, agglomeration was detected very early by looking at the phase-plane invariant. The phase-plane invariant can be used to distinguish changes in fluidized beds due to changes in the flow rate, agglomeration, or various other factors. Therefore, this reliable agglomeration early warning system can be used for better control of circulating fluidized beds.

  2. Fluidized-bed bioreactor system for the microbial solubilization of coal

    Science.gov (United States)

    Scott, C.D.; Strandberg, G.W.

    1987-09-14

    A fluidized-bed bioreactor system for the conversion of coal into microbially solubilized coal products. The fluidized-bed bioreactor continuously or periodically receives coal and bio-reactants and provides for the production of microbially solubilized coal products in an economical and efficient manner. An oxidation pretreatment process for rendering coal uniformly and more readily susceptible to microbial solubilization may be employed with the fluidized-bed bioreactor. 2 figs.

  3. Fluidized-bed bioreactor process for the microbial solubiliztion of coal

    Science.gov (United States)

    Scott, Charles D.; Strandberg, Gerald W.

    1989-01-01

    A fluidized-bed bioreactor system for the conversion of coal into microbially solubilized coal products. The fluidized-bed bioreactor continuously or periodically receives coal and bio-reactants and provides for the production of microbially solubilized coal products in an economical and efficient manner. An oxidation pretreatment process for rendering coal uniformly and more readily susceptible to microbial solubilization may be employed with the fluidized-bed bioreactor.

  4. Mathematical simulation of working processes in the furnace of a circulating fluidized bed boiler

    Energy Technology Data Exchange (ETDEWEB)

    V.A. Dvoinishnikov; A.V. Larkov [Moscow Power Engineering Institute, Moscow (Russian Federation)

    2009-01-15

    A software system developed for simulating and calculating boiler furnaces with circulating fluidized beds is described. The main principles on which the system is constructed are outlined, and the physical and mathematical models of processes in circulating fluidized bed furnaces are described together with the calculation algorithm. Results from a study of analyzing the effect the grinding fineness of initial fuel particles has on the processes in a circulating fluidized bed furnace are presented.

  5. Suspended solid abatement in a conical fluidized bed flocculator

    Institute of Scientific and Technical Information of China (English)

    Dandan ZHOU; Shuangshi DONG; Keyu LI; Huizhong JIANG; Dandan SHANG

    2013-01-01

    With the random movement of silica gel beads in a conical fluidized bed, micro-vortices resulting from the fluidization promoted the collision and aggregation of suspended fine kaolin powders. The abatement efficiencies of the suspended fine solids under several hydrodynamic conditions were studied, and a suitable control strategy for operating the conical fluidized bed flocculators was identified. The suspended solids abatement efficiency was found to increase with increasing Camp Number and flocculation time (T), but decreased with the increase of velocity gradient (G) within the range studied in this research (165.1-189.6s-1). The abatement efficiencies were all more than 60% at the range of G = 165-180 s 1 and T = 15-33 s at an initial kaolin solid concentration of 150mg·L-1, polymer aluminum chloride dosage of 60 mg· L -1 and sedimentation time of 20 min. However, the formation of flocs was influenced by the liquid back- mixing. Excessive backmixing caused the breakup of ftocs and resulted in difficulty for the fine powders to aggregate and sediment to the reactor bottom. The results of the calculated fractal dimension and measured free sedimenta- tion velocity of flocs obtained at different runs showed similar flocs properties, and indicated an easy control strategy for sedimentation of the flocs.

  6. Importance of fragmentation on the steady state combustion of wood char in a bubbling fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Pinho, Carlos [Universidade do Porto (CEFT/FEUP), Porto (Portugal). Faculdade de Engenharia. Centro de Estudos de Fenomenos de Transporte], E-mail: ctp@fe.up.pt

    2010-07-01

    A simple mathematical model for the analysis of the steady state behavior of a bubbling fluidized bed burner is presented, with the main intention of evaluating the importance of the primary fragmentation of fuel particles on the performance of this type of burners. This model has pedagogical advantages because of its simplicity and easiness of application to the analysis of realistic situations. The model is based upon the classical models used for the study of batch combustion processes in fluidized bed reactors. Experimental data from studies of fluidized bed combustion of portuguese vegetable chars are used to support the analysis of the performance of a 1 m diameter fluidized bed combustor. (author)

  7. Requirements of the energy industry on fluidized-bed combustion equipment

    Energy Technology Data Exchange (ETDEWEB)

    Voigtlaender, P.; Weidlich, H.G.

    1984-12-01

    General technological advantages of low-grade brown coal combustion in fluidized-bed chambers are indicated. Brown coal with 7 to 9 MJ/kg calorific value and 25 to 35% dry ash content will be increasingly mined in the GDR. It is recommended that this fuel be used in fluidized-bed equipment, achieving high combustion efficiency with less pollution than in traditional grate combustion. A system with circulating fluidized-bed combustion is superior to a stationary atmospheric system. Combustion research will, therefore, focus on systems with circulating fluidized beds.

  8. CFD Analysis of Bubbling Fluidized Bed Using Rice Husk

    Science.gov (United States)

    Singh, Ravi Inder; Mohapatra, S. K.; Gangacharyulu, D.

    Rice is Cultivated in all the main regions of world. The worldwide annual rice production could be 666million tons (www.monstersandcritics.com,2008) for year 2008. The annual production of rice husk is 133.2 million tons considering rice husk being 20% of total paddy production. The average annual energy potential is 1.998 *1012 MJ of rice husk considering 15MJ/kg of rice husk. India has vast resource of rice husk; a renewable source of fuel, which if used effectively would reduce the rate of depletion of fossil energy resources. As a result a new thrust on research and development in boilers bases on rice husk is given to commercialize the concept. CFD is the analysis of systems involving fluid flow, heat transfer and associated phenomena such as chemical reactions by means of computer-based simulation. High quality Computational Fluid dynamics (CFD) is an effective engineering tool for Power Engineering Industry. It can determine detailed flow distributions, temperatures, and pollutant concentrations with excellent accuracy, and without excessive effort by the software user. In the other words it is the science of predicting fluid flow, heat and mass transfer, chemical reactions and related phenomena; and an innovate strategy to conform to regulations and yet stay ahead in today's competitive power market. This paper is divided into two parts; in first part review of CFD applied to the various types of boilers based on biomass fuels/alternative fuels is presented. In second part CFD analysis of fluidized bed boilers based on rice husk considering the rice husk based furnace has been discussed. The eulerian multiphase model has used for fluidized bed. Fluidized bed has been modeled using Fluent 6.2 commercial code. The effect of numerical influence of bed superheater tubes has also been discussed.

  9. Mass transfer in three-phase fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    Wu, B.W.; Cheng, Y.L.; Perini, J.R.; Roux-Buisson, J.L.

    1978-04-26

    The effects of superficial liquid and gas velocity, particle diameter, liquid viscosity, and column diameter on liquid dispersion (E/sub L) and mass transfer (K/sub L/a) in three-phase fluidized beds were investigated using a water--glycerol/oxygen--nitrogen (or oxygen--argon)/glass-bead system. Overall mass transfer coefficients were calculated based on plug flow, dispersed plug flow, and continuously stirred tank models. k/sub L/a was found to increase with gas velocity and particle diameter, but no correlation of K/sub L/a with liquid velocity was observed. At low liquid velocities, K/sub L/a was lower for the more viscous liquid; the reverse was true at high liquid flow rates. E/sub L/ increased rapidly for liquid flow rates at two to three times the minimum fluidization velocity.

  10. Comparison of packed bed and fluidized bed membrane reactors for methane reforming

    OpenAIRE

    Gallucci, Fausto; Sint Annaland, van, Martin; Kuipers, J.A.M.

    2009-01-01

    In this work the performance of different membrane reactor concepts, both fluidized bed and packed bed membrane reactors, have been compared for the reforming of methane for the production of ultra-pure hydrogen. Using detailed theoretical models, the required membrane area to reach a given conversion and the prevailing temperature profiles have been compared. The extent of mass and heat transfer limitations in the different reactors have been evaluated, and strategies to decrease (or avoid) ...

  11. CFD simulation of fluidization quality in the three-dimensional fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Kai Zhang; Stefano Brandani; Jicheng Bi; Jianchun Jiang

    2008-01-01

    Multiphase computational fluid dynamics (CFD) has become an alternative method to experimental investigation for predicting the fluid dynamics in gas-solid fluidized beds. The model of Brandani and Zhang, which contains additional terms in both the gas-and solid-phase momentum equations, is employed to explore homogeneous fluidization of Geldart type A particles and bubbling fluidizatiou Of Geldart type B particles in three-dimensional gas-fluidized beds. In this model, only a correlation for drag force is necessary to close the governing equations. Two kinds of solids, i. e., fine alumina powder (dp=60μm and ρp=1500kg/m3) and sand (dp=610μm and ρp=2500kg/m3), are numerically simulated in a rectangular duct of 0.2m (long)×0.2m (wide) ×0.5m (high) size. The results show good agreement with the classic theory of Geldart.

  12. Biological reduction of nitrate wastewater using fluidized-bed bioreactors

    International Nuclear Information System (INIS)

    There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3- and as large as 2000 m3/d, in the nuclear fuel cycle as well as in many commercial processes such as fertilizer production, paper manufacturing, and metal finishing. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 gN(NO3-)/m3 by the use of a fluidized-bed bioreactor. The major strain of denitrification bacteria is Pseudomonas which was derived from garden soil. In the fluidized-bed bioreactor the bacteria are allowed to attach to 0.25 to 0.50-mm-diam coal particles, which are fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3. A description is given of the results of two biodenitrification R and D pilot plant programs based on the use of fluidized bioreactors capable of operating at nitrate levels up to 7000 g/m3 and achieving denitrification rates as high as 80 gN(NO3-)/d per liter of empty bioreactor volume. The first of these pilot plant programs consisted of two 0.2-m-diam bioreactors, each with a height of 6.3 m and a volume of 208 liters, operating in series. The second pilot plant was used to determine the diameter dependence of the reactors by using a 0.5-m-diam reactor with a height of 6.3 m and a volume of 1200 liters. These pilot plants operated for a period of six months and two months respectively, while using both a synthetic waste and the actual waste from a gaseous diffusion plant operated by Goodyear Atomic Corporation

  13. Performance of a bench-scale fast fluidized bed carbonator

    DEFF Research Database (Denmark)

    Pathi, Sharat Kumar; Lin, Weigang; Illerup, Jytte Boll;

    2014-01-01

    The carbonate looping process is a promising technology for CO2 capture from flue gas. In this process, the CO2 capture efficiency depends on the performance of a carbonator that may be operated as a circulating fluidized bed (CFB). In this paper, the carbonator performance is investigated...... is estimated from experiments under stable operating conditions with constant bed inventory, reactor temperature and exit CO2 concentration. The validated CFB carbonator model was used to simulate different operating conditions relevant for CO2 capture from a power plant and from a cement plant. The results...... show that particle recirculation rates of 2-5 kg/(m2s) or ratio of bed inventory to recirculation rates of 70-176 s are sufficient for attaining 90% CO2 capture efficiency depending on the inlet Ca to C ratio. © 2014 American Chemical Society....

  14. Modeling moisture diffusivity, activation energy and specific energy consumption of squash seeds in a semi fluidized and fluidized bed drying

    OpenAIRE

    Chayjan, Reza Amiri; Salari, Kamran; Abedi, Qasem; Sabziparvar, Ali Akbar

    2011-01-01

    This study investigated thin layer drying of squash seeds under semi fluidized and fluidized bed conditions with initial moisture content about 83.99% (d.b.). An experimental fluidized bed dryer was also used in this study. Air temperature levels of 50, 60, 70 and 80 °C were applied in drying samples. To estimate the drying kinetic of squash seed, seven mathematical models were used to fit the experimental data of thin layer drying. Among the applied models, Two-term model has the best perfor...

  15. An Experimental Investigation on the Drying of Sliced Food Products in Centrifugal Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    M.H.Shi; Y.L.Hao; 等

    1998-01-01

    An experimental investigation on the fluidization and drying characteristics of sliced food products in a centrifugal fluidized bed dryer was carried out,The rotaing speed ranges from 300 rpm to 500 rpm.Sliced potato and radish were used as the testing materials.The results show that the sliced materials can be fluidized well in the centrifugal fluidized bed.The fluidized curve has a maximum value and the critical fluidized velocities vary with the type of the test material,its shape and dimension as well as operating parameters.The sliced food materials can be dried very well and fast in the centrifugal fluidized bed with a large productivity.The factors that influence the drying process were examined and discussed.The final shape and inner structure of the dried products were observed.The water recovery characteristics of the drried products were also investigated.

  16. Enhanced Productivity of Chemical Processes Using Dense Fluidized Beds

    Energy Technology Data Exchange (ETDEWEB)

    Sibashis Banerjee; Alvin Chen; Rutton Patel; Dale Snider; Ken Williams; Timothy O' Hern; Paul Tortora

    2008-02-29

    The work detailed in this report addresses Enabling Technologies within Computational Technology by integrating a “breakthrough” particle-fluid computational technology into traditional Process Science and Engineering Technology. The work completed under this DOE project addresses five major development areas 1) gas chemistry in dense fluidized beds 2) thermal cracking of liquid film on solids producing gas products 3) liquid injection in a fluidized bed with particle-to-particle liquid film transport 4) solid-gas chemistry and 5) first level validation of models. Because of the nature of the research using tightly coupled solids and fluid phases with a Lagrangian description of the solids and continuum description of fluid, the work provides ground-breaking advances in reactor prediction capability. This capability has been tested against experimental data where available. The commercial product arising out of this work is called Barracuda and is suitable for a wide (dense-to-dilute) range of industrial scale gas-solid flows with and without reactions. Commercial applications include dense gas-solid beds, gasifiers, riser reactors and cyclones.

  17. The Physical Models of Cyclone Diplegs in Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    K.Smolders; D.Geldart; J.Baeyens

    2001-01-01

    In most industrial fluidization units, two- or three-stage cyclone systems are used to clean the product gases. To return the solids to the bed, these cyclones are fitted with diplegs. By pass of gas from the bed through the dipleg is partially overcome by the back pressure build-up in the dipleg and by adding a trickle valve at the bottom of the dipleg. Diplegs of primary cyclones, operating at a high solid loading behave differently from diplegs of secondary and tertiary cyclones which operate at low solid loading. Both types have been investigated by pressure drop measurements, visual observation and by measurements of the air flow rate flowing up the riser. The primary dipleg was also studied using electrical capacitance tomography. The results are reported hereafter and will give a first indication towards the right design of the dipleg and the selection of the trickle valve. The influence of gas flow in the dipleg on the conversion in a catalytic fluidized bed reactor is found to be negligible.

  18. Thermofluid effect on energy storage in fluidized bed reactor

    Science.gov (United States)

    Mahfoudi, Nadjiba; El Ganaoui, Mohammed; Moummi, Abdelhafid

    2016-05-01

    The development of innovative systems of heat storage is imperative to improve the efficiency of the existing systems used in the thermal solar energy applications. Several techniques were developed and realized in this context. The technology of the sand fluidized bed (sandTES) offers a promising alternative to the current state-of-the-art of the heat storage systems, such as fixed bed using a storage materials, as sand, ceramic, and stones, etc. Indeed, the use of the fluidization technique allows an effective heat transfer to the solid particles. With the sand, an important capacity of storage is obtained by an economic and ecological material [N. Mahfoudi, A. Moummi, M. El Ganaoui, Appl. Mech. Mater. 621, 214 (2014); N. Mahfoudi, A. Khachkouch, A. Moummi B. Benhaoua, M. El Ganaoui, Mech. Ind. 16, 411 (2015); N. Mahfoudi, A. Moummi, M. El Ganaoui, F. Mnasri, K.M. Aboudou, 3e Colloque internationale Francophone d"énergétique et mécanique, Comores, 2014, p. 91]. This paper presents a CFD simulation of the hydrodynamics and the thermal transient behavior of a fluidized bed reactor of sand, to determine the characteristics of storage. The simulation shows a symmetry breaking that occurs and gave way to chaotic transient generation of bubble formation after 3 s. Furthermore, the predicted average temperature of the solid phase (sand) increases gradually versus the time with a gain of 1 °C in an interval of 10 s. Contribution to the topical issue "Materials for Energy Harvesting, Conversion and Storage (ICOME 2015) - Elected submissions", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

  19. Agricultural uses of alkaline fluidized bed combustion ash: case studies

    Energy Technology Data Exchange (ETDEWEB)

    Stout, W.L.; Daily, M.R.; Nickeson, T.L.; Svendson, R.L.; Thompson, G.P. [USDA-ARS, University Park, PA (United States)

    1997-06-01

    Successful programmes were developed by Ahlstrom Development Ash Corporation and Air Products and Chemical for using fluidized bed combustion ash as a substitute for agricultural lime on dairy farms in northern New York state and on fruit and nut crops in the San Joaquin Valley of California. The companies developed these programmes by utilizing the methodology developed through USDA-ARS research and working closely with agricultural consultants and regulatory agencies to ensure that the ash applications were both agronomically and environmentally sound. 1 ref.

  20. DRY CLEANING OF COAL WITH AIR DENSE MEDIUM FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    陈清如; 杨毅; 余智敏; 李建明

    1990-01-01

    This paper deals with the experimental study of dry cleaning of coal with air dense medium fluidized bed. This technique opens up an efficient way of coal separation for vast areas in the country where water resources are in short supply or coals tend to slime seriously in wet process. Tests show that it can separate any kind of coal (6--50mm) efficiently. The probable error E, can reach 0.05--0.08. The separating density can be adjusted in the range of 1.0--2.0 g/cm3. This technique brings about enormous economic benifits.

  1. Dynamic stability of a fluidized-bed nuclear reactor

    International Nuclear Information System (INIS)

    Recent advances in the study of a fluidized-bed nuclear reactor's stability, due to short and long time transients, are discussed. The point-kinetic model, which considers flux variation in the axial direction, is applied to study short time transients, and the theory of bifurcation is used for long time transients. Numerical results are presented for both transients. The preliminary results indicate that this concept of a nuclear reactor has a behavior similar to that of a conventional reactor regarding its dynamic stability

  2. Fluidized bed incineration process design for transuranic waste

    International Nuclear Information System (INIS)

    A fluidized bed incineration facility has been installed at the Rocky Flats Plant to develop and demonstrate a process for the combustion of transuranic waste. The unit's capacity is about 82 kg/hr of combustible solid waste, which is nine times higher than the rate for the operating pilot-scale unit. The facility utilizes nonaqueous, in situ neutralization of acid gases. These gases are generated during the combustion of halogen-containing materials. The low-temperature (550 0C) operation eliminates refractory-lined equipment

  3. Kinetics of potato drying using fluidized bed dryer.

    Science.gov (United States)

    Bakal, Sushant Balasaheb; Sharma, Gyanendra Prasad; Sonawane, Somnath P; Verma, Radhachran C

    2012-10-01

    The effect of air temperature and two different shapes (cuboidal and cylindrical) with 3 aspect ratio of each shape on the drying kinetics of potato (Solanum tuberosum) in fluidized bed dryer was investigated. Drying was carried out at 50, 60 and 70°C at 7 m/s air velocity. Drying data were analysed to obtain effective diffusivity of moisture transfer. During drying moisture transfer from potato were described by Fick's diffusion model. Two mathematical models were fitted to experimental data. The Page model gave better fit than simple exponential model. The Arrehnious activation energy value expresses the effect of temperature on diffusivity. PMID:24082273

  4. NUCLA Circulating Atmospheric Fluidized Bed Demonstration Project. Annual report, 1988

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    This Annual Report on Colorado-Ute Electric Association`s NUCLA Circulating Fluidized Bed (CFB) Demonstration Program covers the period from February 1987 through December 1988. The outline for presentation in this report includes a summary of unit operations along with individual sections covering progress in study plan areas that commenced during this reporting period. These include cold-mode shakedown and calibration, plant commercial performance statistics, unit start-up (cold), coal and limestone preparation and handling, ash handling system performance and operating experience, tubular air heater, baghouse operation and performance, materials monitoring, and reliability monitoring. During this reporting period, the coal-mode shakedown and calibration plan was completed. (VC)

  5. Gasification of sawdust in pressurised internally circulating fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Maartensson, R.; Lindblom, M. [Lund Univ. (Sweden). Dept. of Chemical Engineering

    1996-12-31

    A test plant for pressurised gasification of biofuels in a internally circulating fluidized bed has been built at the department of Chemical Engineering II at the University of Lund. The design performance is set to maximum 20 bar and 1 050 deg C at a thermal input of 100 kW or a maximum fuel input of 18 kg/in. The primary task is to study pressurised gasification of biofuels in relation to process requirements of the IGCC concept (integrated gasification combined cycle processes), which includes studies in different areas of hot gas clean-up in reducing atmosphere for gas turbine applications. (orig.)

  6. Thermal energy storage systems using fluidized bed heat exchangers

    Science.gov (United States)

    Ramanathan, V.; Weast, T. E.; Ananth, K. P.

    1980-01-01

    The viability of using fluidized bed heat exchangers (FBHX) for thermal energy storage (TES) in applications with potential for waste heat recovery was investigated. Of the candidate applications screened, cement plant rotary kilns and steel plant electric arc furnaces were identified, via the chosen selection criteria, as having the best potential for successful use of FBHX/TES system. A computer model of the FBHX/TES systems was developed and the technical feasibility of the two selected applications was verified. Economic and tradeoff evaluations in progress for final optimization of the systems and selection of the most promising system for further concept validation are described.

  7. Fluidized bed and method and system for gas component capture

    Energy Technology Data Exchange (ETDEWEB)

    Krutka, Holly; Wilson, Cody; Starns, Travis

    2016-05-31

    The present disclosure is directed to a process that allows dry sorbents to remove a target constituent, such as carbon dioxide (CO.sub.2), from a gas stream. A staged fluidized bed separator enables gas and sorbent to move in opposite directions. The sorbent is loaded with target constituent in the separator. It is then transferred to a regenerator where the target constituent is stripped. The temperature of the separator and regenerator are controlled. After it is removed from the regenerator, the sorbent is then transferred back to the separator.

  8. Fluidized bed layer-by-layer microcapsule formation.

    Science.gov (United States)

    Richardson, Joseph J; Teng, Darwin; Björnmalm, Mattias; Gunawan, Sylvia T; Guo, Junling; Cui, Jiwei; Franks, George V; Caruso, Frank

    2014-08-26

    Polymer microcapsules can be used as bioreactors and artificial cells; however, preparation methods for cell-like microcapsules are typically time-consuming, low yielding, and/or involve custom microfluidics. Here, we introduce a rapid (∼30 min per batch, eight layers), scalable (up to 500 mg of templates), and efficient (98% yield) microcapsule preparation technique utilizing a fluidized bed for the layer-by-layer (LbL) assembly of polymers, and we investigate the parameters that govern the formation of robust capsules. Fluidization in water was possible for particles of comparable diameter to mammalian cells (>5 μm), with the experimental flow rates necessary for fluidization matching well with the theoretical values. Important variables for polymer film deposition and capsule formation were the concentration of polymer solution and the molecular weight of the polymer, while the volume of the polymer solution had a negligible impact. In combination, increasing the polymer molecular weight and polymer solution concentration resulted in improved film deposition and the formation of robust microcapsules. The resultant polymer microcapsules had a thickness of ∼5.5 nm per bilayer, which is in close agreement with conventionally prepared (quiescent (nonflow) adsorption/centrifugation/wash) LbL capsules. The technique reported herein provides a new way to rapidly generate microcapsules (approximately 8 times quicker than the conventional means), while being also amenable to scale-up and mass production.

  9. INVESTIGATION OF FUEL CHEMISTRY AND BED PERFORMANCE IN A FLUIDIZED BED BLACK LIQUOR STEAM REFORMER

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2003-12-01

    The University of Utah project ''Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer'' (DOE award number DE-FC26-02NT41490) was developed in response to a solicitation for projects to provide technical support for black liquor and biomass gasification. The primary focus of the project is to provide support for a DOE-sponsored demonstration of MTCI's black liquor steam reforming technology at Georgia-Pacific's paper mill in Big Island, Virginia. A more overarching goal is to improve the understanding of phenomena that take place during low temperature black liquor gasification. This is achieved through five complementary technical tasks: (1) construction of a fluidized bed black liquor gasification test system, (2) investigation of bed performance, (3) evaluation of product gas quality, (4) black liquor conversion analysis and modeling and (5) computational modeling of the Big Island gasifier. Four experimental devices have been constructed under this project. The largest facility, which is the heart of the experimental effort, is a pressurized fluidized bed gasification test system. The system is designed to be able to reproduce conditions near the black liquor injectors in the Big Island steam reformer, so the behavior of black liquor pyrolysis and char gasification can be quantified in a representative environment. The gasification test system comprises five subsystems: steam generation and superheating, black liquor feed, fluidized bed reactor, afterburner for syngas combustion and a flue gas cooler/condenser. The three-story system is located at University of Utah's Industrial Combustion and Gasification Research Facility, and all resources there are available to support the research.

  10. An Experimental and Numerical Investigation of Fluidized Bed Gasification of Solid Waste

    OpenAIRE

    Sharmina Begum; Mohammad G. Rasul; Delwar Akbar; David Cork

    2013-01-01

    Gasification is a thermo-chemical process to convert carbon-based products such as biomass and coal into a gas mixture known as synthetic gas or syngas. Various types of gasification methods exist, and fluidized bed gasification is one of them which is considered more efficient than others as fuel is fluidized in oxygen, steam or air. This paper presents an experimental and numerical investigation of fluidized bed gasification of solid waste (SW) (wood). The experimental measurement of syngas...

  11. A discrete particle simulation study on the influence of restitution coefficient on spout fluidized bed dynamics

    NARCIS (Netherlands)

    Buijtenen, van M.S.; Deen, N.G.; Antonyuk, S.; Heinrich, S.; Kuipers, J.A.M.

    2008-01-01

    In this paper the influence of the normal restitution coefficient on the bed dynamics during different flow regimes was studied using the discrete element model. The three flow regimes comprise the intermediate/spout-fluidization, spouting-with-aeration regime and the jetin- fluidized-bed. It is sho

  12. DETERMINATION OF MARGINALLY STABLE ZONE OF GAS-SOLID MAGNETICALLY FLUIDIZED BEDS

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The void fluctuation of magnotically fluidized beds was analyzed and their maginally stable zone was determined. The analysis was based on the two-phase model of magnetically fluidized bed and wave theory. The marginally stable zone determined by this paper matches well with the experimental results.

  13. Mechanistic modelling of fluidized bed drying processes of wet porous granules

    DEFF Research Database (Denmark)

    Mortier, Séverine Thérèse F.C.; De Beer, Thomas; Gernaey, Krist;

    2011-01-01

    Fluidized bed dryers are frequently used in industrial applications and also in the pharmaceutical industry. The general incentives to develop mechanistic models for pharmaceutical processes are listed, and our vision on how this can particularly be done for fluidized bed drying processes of wet ...

  14. Development of a new method for improving load turndown in fluidized bed combustors: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brown, R.C.

    1988-12-01

    The objective of this research was to investigate a new concept in fluidized bed design that improves load turndown capability. This improvement is accomplished by independently controlling heat transfer and combustion in the combustor. The design consists of two fluidized beds, one central and one annular. The central bed serves as the combustion bed. The annular bed is fluidized separately from the combustion bed and its level of fluidization determine the overall heat transfer rate from the combustion bed to the surrounding water jacket. Early theoretical considerations suggested a load turndown exceeding ten was possible for this design. This research consisted of three major phases: development of a computational model to predict heat transfer in the two-bed combustor, heat transfer measurements in hot-and-cold flow models of the combustor, and combustion tests in an optimally designed combustor. The computation model was useful in selecting the design of the combustor. Annular bed width and particle sizes were chosen with the aid of the model. The heat transfer tests were performed to determine if the existing correlations for fluidized bed heat transfer coefficients were sufficiently accurate for high aspect ratio fluidized beds (such as the annular bed in the combustor). Combustion tests were performed in an optimally designed combustor. Three fuel forms were used: double screened, crushed coal, coal-water-limestone mixtures (CWLM), and coal-limestone briquettes. 18 refs., 30 figs., 8 tabs.

  15. Effect of bed particles to combustion of gases in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Raiko, R.; Wallen, V.; Etelaeaho, R.; Correia, S. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

    1997-10-01

    The objective of this project was to obtain experimental data on effects of sand particles to the combustion of gases. The effect of the surface area of the particles was tested using different sized particles. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 42 mm surrounded by an electric heater. The test rig was built in the Laboratory of Energy and Process Engineering at Tampere University of Technology. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies were conducted with both fresh bed particles and used bed particles. These measurements indicate that carbon monoxide significantly reacts with oxygen in the particulate or emulsion phase of a fluidized bed, if the residence time is long enough. The reaction rate depends mainly on temperature, air coefficient, residence time and particle size of the solids. It seems that the combustion enhances if the average particle size increases. Whether this is caused by increased free path length or reduced specific surface area of the bed is yet unknown. The first might be more probable cause because the majority of reactions often took place in the freeboard right above the bed. It was clear that the bed hindered proper combustion in several cases. (orig.)

  16. Sludge combustion in fluidized bed reactors at laboratory scale

    International Nuclear Information System (INIS)

    The combustion of a dried sewage sludge in laboratory scale fluidized bed has been studied in Naples by the Istituto di ricerche sulla combustione (Irc) in the framework of a National project named Thermal Process with Energy Recovery to be used in laboratory and pre-pilot scale apparatus. The attention has been focused on emissions of unreacted carbon as elutriated fines, on the emissions of pollutant gases and on the assessment of the inventory of fly- and bottom ashes. The combustion behaviour of sewage sludge has been compared with those of a market available Tyre Derived Fuel (TDF) and a biomass from Mediterranean area (Robinia Pseudoacacia) and with that of a South African bituminous coal. Stationary combustion tests were carried out at 8500 C by feeding particles in the size range 0-1 mm into a bed of silica sand without any sorbent addition. The fluidized bed combustor has been operated, at a superficial gas velocity of 0.4 m/s and different excesses of air ranging between 14 and 98%. Relatively high combustion efficiency, larger than 98.9% has been obtained in experiments carried out with sewage sludge and excess of air larger than 20%. These values, are comparable with those obtained in previously experimental activity carried out under similar operative conditions with a South Africa Bituminous coal (97-98%). It is larger than those obtained by using a Tyre Derived Fuel (89-90%) and the Robinia Pseudoacacia Biomass (93-93%). The relative importance of carbon fines elutriation, CO emissions and volatile bypassing the bed in determining the loss of combustion efficiency has been evaluated for the different fuels tested

  17. Vibrated fluidized bed air classification of moist raw coal

    Institute of Scientific and Technical Information of China (English)

    杨国华; 赵跃民; 陈清如

    2002-01-01

    Vibrated fluidized bed air classification is completely different from traditional screening in principle. It extracts fine coal from moist raw coal by entrainment of an ascending airflow in a vibrated fluidized bed. Pilot tests showed that air classification efficiencies varied from 74.85% to 93.84% at cut-size 6, 4, 3, 2, 1, and 0.5 mm when free moisture of coal is in the range of 1.7% to 9.5%, and ash contents of fine coal products were 2%~3% lower than those of the same size fractions in feed, and 4%~10% lower than those of feeds for most cases because of the density differences between coal and waste, which is beneficial to producing lower ash fine coal from raw coal as fuel of blast furnaces or pulverized coal firing boilers. A commercial unit of 100 t/h has been in smooth operation, and several 300~400 t/h units are in plan or construction.

  18. Co-combustion of waste materials using fluidized bed technology

    Energy Technology Data Exchange (ETDEWEB)

    M. Lopes; I. Gulyurtlu; P. Abelha; T. Crujeira; D. Boavida; I. Cabrita [INETI-DEECA, Lisbon (Portugal)

    2004-07-01

    There is growing interest in using renewable fuels in order to sustain the CO{sub 2} accumulation. Several waste materials can be used as coal substitutes as long as they contain significant combustible matter, as for example MSW and sewage sludge. Besides the outcome of the energetic valorization of such materials, combustion must be regarded as a pre-treatment process, contributing to the safe management of wastes. Landfilling is an expensive management option and requires a previous destruction of the organic matter present in residues, since its degradation generates greenhouse gases and produces acidic organic leachates. Fluidized bed combustion is a promising technology for the use of mixtures of coal and combustible wastes. This paper presents INETI's experience in the co-combustion of coal with this kind of residues performed in a pilot fluidized bed. Both the RDF (from MSW and sewage sludge) and sewage sludge combustion problems were addressed, relating the gaseous emissions, the behaviour of metals and the leachability of ashes and a comparison was made between co-combustion and mono-combustion in order to verify the influence of the utilization of coal. 9 refs., 1 fig., 3 tabs.

  19. Atmospheric fluidized bed combustor development program. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ashworth, R.A.; Melick, T.A.; Plessinger, D.A.; Sommer, T.M. [Energy and Environmental Research Corp., Orville, OH (United States); Keener, H.M. [Ohio State Univ., Columbus, OH (United States). Ohio Agricultural Research and Development Center; Webner, R.L. [Will-Burt, Orrville, OH (United States)

    1995-12-01

    The objective of this project was to demonstrate and promote the commercialization of a coal-fired atmospheric fluidized bed combustion (AFBC) system, with limestone addition for SO{sub 2} emissions control and a baghouse for particulate emissions control. This AFBC system was targeted for small scale industrial-commercial-institutional space and process heat applications in the 1 x 10{sup 6} to 10 x 10{sup 6} Btu/hr capacity range. A cost effective and environmentally acceptable AFBC technology in this size range would displace a considerable amount of gas/oil with coal while resulting in significant total cost savings to the owner/operators. The project itself was separated into three levels: (1) feasibility, (2--3) subsystem development and integration, and (4) proof-of-concept. In Level (1), the technical and economic feasibility of a 1 million Btu/hr coal-fired AFBC air heater was evaluated. In Level (2--3), the complete EER fluidized bed combustor (1.5 million Btu/hr) system was developed and tested. The goal or reducing SO{sub 2} emissions to 1.2 lb/10{sup 6} Btu, from high sulfur Ohio coal, was achieved by adding limestone with a Ca/S (coal) ratio of {approximately} 3.0. Finally, in Level (4), the proof-of-concept system, a 2.2 million Btu/hr unit was installed and successfully operated at Cedar Lane Farms, a commercial nursery in Ohio.

  20. Cold-Flow Circulating Fluidized-Bed Identification

    Energy Technology Data Exchange (ETDEWEB)

    Parviz Famouri

    2005-07-01

    In a variety of industrial applications, the use of a circulating fluidized bed (CFB) provides various advantages, such as reducing environmental pollution and increasing process efficiency. The application of circulating fluidized bed technology contributes to the improvement of gas-solid contact, reduction of the cross-sectional area with the use of higher superficial velocities, the use of the solids circulation rate as an additional control variable, and superior radial mixing, Grace et al. [1]. In order to improve raw material usage and utility consumption, optimization and control of CFB is very important, and an accurate, real time model is required to describe and quantify the process. Currently there is no accepted way to construct a reliable model for such a complex CFB system using traditional methods, especially at the pilot or industrial scale. Three major obstacles in characterizing the system are: 1) chaotic nature of the system; 2) non-linearity of the system, and 3) number of immeasurable unknowns internal to the system,[2]. Advanced control theories and methods have the ability to characterize the system, and can overcome all three of these obstacles. These methods will be discussed in this report.

  1. Fluidized bed combustion. volume 3. 1978-March, 1980 (citations from the NTIS data base). Report for 1978-Mar 80

    Energy Technology Data Exchange (ETDEWEB)

    Cavagnaro, D.M.

    1980-03-01

    The bibliography cites studies on fluidized bed processes and processors for the combustion of coal, oil, and industrial and municipal wastes. It also covers sludge incineration, fluidized bed boilers, and air pollution control by fluidized bed combustion. (This updated bibliography contains 240 abstracts, 91 of which are new entries to the previous edition.)

  2. Fluidized bed combustion. volume 2. 1977-March, 1980 (citations from the Engineering Index data base). Report for 1977-mar 80

    Energy Technology Data Exchange (ETDEWEB)

    Cavagnaro, D.M.

    1980-03-01

    The cited reports from a worldwide literature survey cover the fluidized bed processes and processors for the combustion of oil, coal, and industrial as well as municipal wastes. It also includes sludge incineration, fluidized bed boilers, and air pollution abatement by fluidized bed combustion. (This updated bibliography contains 390 abstracts, 165 of which are new entries to the previous edition.)

  3. Use of activated carbon and natural zeolite as support materials, in an anaerobic fluidised bed reactor, for vinasse treatment.

    Science.gov (United States)

    Fernández, N; Fdz-Polanco, F; Montalvo, S J; Toledano, D

    2001-01-01

    In Cuba, the alcohol distillation process from cane sugar molasses, produces a final waste (vinasse), with an enormous polluting potential and a high sulfate content. Applying the anaerobic technology, most of the biodegradable organic matter can turn into biogas, rich in methane but with concentrations of sulfide above 1%. The present work develops two experiences with anaerobic fluidized bed reactors (AFBR) using both Cuban raw material, activated carbon and natural zeolite, as support media, with the purpose of obtaining high organic matter removal rates and keeping sulfide and ammonium concentrations in the permissible ranges. The reactors were operated during 120 days, achieving an organic loading rate of 10 kg COD/m3 day, with COD removal above 70%, and a methane production of 2 L/d. The activated carbon and natural zeolite used support materials in anaerobic fluidized bed reactors, and showed good results of distillery waste removal. PMID:11575071

  4. Artificial neural network models for biomass gasification in fluidized bed gasifiers

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Hernández, J. Alfredo; Bruno, Joan Carles;

    2013-01-01

    Artificial neural networks (ANNs) have been applied for modeling biomass gasification process in fluidized bed reactors. Two architectures of ANNs models are presented; one for circulating fluidized bed gasifiers (CFB) and the other for bubbling fluidized bed gasifiers (BFB). Both models determine...... bed gasifier can be successfully predicted by applying neural networks. ANNs models use in the input layer the biomass composition and few operating parameters, two neurons in the hidden layer and the backpropagation algorithm. The results obtained by these ANNs show high agreement with published...

  5. Measurement of the fluidized velocity in gas-solid fluidized beds based on AE signal analysis by wavelet packet transform

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    An energy distribution theory was presented based on regular evolvement of energy fraction of acous-tic signals with fluidization velocity. Wavelet packet analysis was used in processing the acoustic sig-nals originated from particle impact on the wall of a fluidized bed. A new criterion of judging incipient fluidization(Umf) velocity and minimum turbulent velocity(Umt) was proposed according to the energy distribution theory. Experiments were performed with five groups of high density polyethylene(PE) particles and one bimodal PE to acquire incipient fluidization velocity and minimum turbulent velocity by using the criterion. The feasibility of this method in obtaining characteristic fluidization parameters was further verified by comparing it to results from the pressure drop method and the empirical value from industry.

  6. Las degradation in a fluidized bed reactor and phylogenetic characterization of the biofilm

    Directory of Open Access Journals (Sweden)

    L. L. Oliveira

    2013-09-01

    Full Text Available A fluidized bed reactor was used to study the degradation of the surfactant linear alkylbenzene sulfonate (LAS. The reactor was inoculated with anaerobic sludge and was fed with a synthetic substrate supplemented with LAS in increasing concentrations (8.2 to 45.8 mg l-1. The removal efficiency of 93% was obtained after 270 days of operation. Subsequently, 16S rRNA gene sequencing and phylogenetic analysis of the sample at the last stage of the reactor operation recovered 105 clones belonging to the domain Bacteria. These clones represented a variety of phyla with significant homology to Bacteroidetes (40%, Proteobacteria (42%, Verrucomicrobia (4%, Acidobacteria (3%, Firmicutes (2%, and Gemmatimonadetes (1%. A small fraction of the clones (8% was not related to any phylum. Such phyla variety indicated the role of microbial consortia in degrading the surfactant LAS.

  7. Bubbling fluidized bed retrofit with modern design tools

    Energy Technology Data Exchange (ETDEWEB)

    Korhonen, S.; Jacobson, T.; Jaeaeskelaeinen, K.; Hulkkonen, S.

    1999-07-01

    Imatran Voima Oy (IVO) has experience of more than 10 years in the design, construction and operation of power plants utilizing fluidized bed boilers (BFB). This operating experience, together with active fuels testing and the development work of computer aided design tools, has offered IVO a good possibility for product development. The new product was demonstrated by converting an old grate fired boiler into BFB at IVO's Vanaja plant. This boiler conversion project and the computational fluid dynamics (CFD) based tool used in the design of the combustion will be presented. The results of the model verification will be described briefly. At the Vanaja plant, a 60 MW{sub coal} fired grate boiler built in the early 1950s was converted to BFB in 1997. The old chain grate was removed and replaced with a fluidized bed with appropriate fluidization air and biofuel feeding systems. The automation system was also modernized. The primary fuel was changed to peat, whereas coal remained as secondary fuel together with natural gas and biofuels. IVO has long tradition in the computational fluid dynamics (CFD) aided engineering of combustion processes. Since 1990, Ardemus, a CFD based combustion modeling package has been applied for pulverized coal combustion. Recently Ardemus has also been applied to the simulation of the freeboard of BFB. The development work is still going on concerning the bed behavior and emission formation description. In the retrofit project, the change of the fuel and the combustion technology were analyzed with the Ardemus model. Because of the shortness of the furnace, the focus in the design process was laid on the optimization of air staging and adequate mixing of combustion air and fuel. The effect of the modification on the operating conditions of the turbine plant was calculated with a process simulator. The design was completed by cold model tests. The modified boiler was commissioned successfully at the beginning of 1998, which is the most

  8. Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2007-06-30

    University of Utah's project entitled 'Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer' (DOE Cooperative Agreement DE-FC26-02NT41490) was developed in response to a solicitation released by the U.S. Department of Energy in December 2001, requesting proposals for projects targeted towards black liquor/biomass gasification technology support research and development. Specifically, the solicitation was seeking projects that would provide technical support for Department of Energy supported black liquor and biomass gasification demonstration projects under development at the time.

  9. The relationship of fluidized bed technology to the U.S. Clean Coal Technology demonstration program

    International Nuclear Information System (INIS)

    Fluidized Bed Combustion projects (both AFBCs and PFBCs) have a prominent role in the US DOE Clean Coal Technology (CCT) Program. This program has the successful commercialization of these technologies as its primary objective and this is the basic criterion for government funding and participation in the development and demonstration of the technologies. Under the CCT program the US DOE is actively involved in the development and operation of three Fluidized Bed Technology projects, NUCLA, TIDD, and SPORN, and is in the negotiation stage on others, Dairyland, Nichols and Tallahassee. All of these projects, along with the operating information on fluidized beds in the industrial sector, will provide a basis for evaluating future utilization of Fluidized Bed Technology in the market place. Impacting upon further utilization will be the time-frame and the Clean Air Act Amendments of 1990. This paper presents the results of a study to ascertain the commercial readiness of Fluidized Bed Technology to meet the emissions and time-frame requirements of the Clean Air Act Amendments of 1990. Specifically addressed are: Commercialization criteria/factors which candidate and/or existing CCTs must achieve in order to gain market acceptance. The status of Fluidized Bed Technology in achieving these commercialization criteria for market acceptance (industrial and utility) consistent with the time frame of the Clean Air Act Amendments of 1990. Recommendations of commercialization criteria for future fluidized bed CCT demonstration projects

  10. EXPERIMENTAL RESEARCH OF CYLINDER-TO-BED HEAT TRANSFER IN AGITATED FLUIDIZED BEDS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Cylinder-to-bed heat transfer in agitated fluidized beds was studied experimentally.In the experiments, the aluminum particles were used as bed material, the diameter of which ranges from 0.5mm to 2mm.The effects of gas velocity, particles size, and agitator rotary speed on heat transfer were studied.From the experimental results, we have come to the following conclusions: (1) There are optimal ranges for airflow velocity and rotary speed to get optimal heat transfer coefficient; (2) The cylinder-to-bed heat transfer is greatly affected by gas velocity, rotary speed and particles sizes and the effect of rotary speed on heat transfer is similar to that of gas velocity; (3) Higher heat transfer coefficient is obtained with smaller particles.

  11. Olive cake combustion in a circulating fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Topal, H.; Durmaz, A. [Gazi Univ, Ankara (Turkey). Dept. of Mechanical Engineering; Atimtay, A.T. [Middle East Technical Univ., Ankara (Turkey). Dept. of Environmental Engineering

    2002-07-01

    This paper presents the results of a study in which an environmentally sound technology was developed for biomass usage for energy production in Turkey. A circulating fluidized bed of 125 mm diameter and 1,800 mm height was used to determine the combustion characteristics of olive cake (OC) produced in Turkey. Olive cake, an olive oil milling waste product, is available in large amounts at a very low cost. Efficient use of OC in energy production solves the problem of waste management and contributes to meeting targets of the Kyoto Protocol. In this study, olive cake alone and olive cake plus lignite mixtures were burned in separate experiments and in various ratios. A new feeding mechanism was developed to feed the olive cake to the bed. On-line concentrations of oxygen, sulphur dioxide, carbon dioxide, carbon monoxide, nitrogen oxides and total hydrocarbons were measured in the flue gas along with temperature distribution in the bed. Emissions were compared with national standards and combustion efficiency of the olive cake plus lignite coal mixtures and olive cake alone were calculated. The optimum operating parameters were described. OC burned with 94 to 98.5 per cent efficiency. The combustion efficiency increased with increased excess air ratio because volatiles released from the fuel were burned more completely. 3 refs., 5 tabs., 6 figs.

  12. Improved Fluidized Bed Drying Technology for Wood Fuels

    Energy Technology Data Exchange (ETDEWEB)

    Berghel, Jonas

    2004-04-01

    In this thesis, I discuss experiences from designing, building and evaluating two research plants, which use circulating, atmospheric pressure superheated steam as drying medium for drying sawdust in a fluidized bed. The increased use of pellets has created a demand for new drying equipment at the Swedish pellet plants. The underlying cause is that almost all of the available dried material, such as wood shavings, is already in use. The remaining biofuel materials, primarily wet sawdust need drying before entering the pellet process. The primary demands on the drying process were an uncomplicated design and efficient energy use. A key aim was to improve the drying technique used in the Swedish wood fuel system with specially interest on the control system. Sawdust has been tested in both a full scale and a laboratory scale dryers. The tests were done in a spouted bed. The product of the steam mass flow and the enthalpy difference limits the drying capacity. The tests showed that it is possible to use the temperature after the dryer as a control parameter for the outgoing moisture content in a spouted bed dryer. The results and conclusions can be very useful when designing a similar full scale drying system.

  13. Thermodynamic analysis of fluidized bed drying of carrot cubes

    International Nuclear Information System (INIS)

    In this study, the energy and exergy analyses of fluidized bed drying of carrot cubes were investigated. Drying experiments were conducted at inlet air temperatures of 50, 60, and 70 oC, BD (bed depths) of 30, 60, and 90 mm and square-cubed carrot dimensions of 4, 7, and 10 mm. The effects of drying variables on energy utilization, energy utilization ratio, exergy loss and exergy efficiency were studied. The energy utilization and energy utilization ratio varied between 0.105-1.949 kJ/s and 0.074-0.486, respectively. The exergy loss and exergy efficiency were found to be in the range of 0.206-1.612 kJ/s and 0.103-0.707, respectively. The results showed that small particles, deep beds and high inlet air temperatures increased energy utilization, energy utilization ratio, and exergy loss due to high value of heat and mass transfer. Also, the exergy efficiency had maximum value when higher drying air temperature, larger CS (cube size) and shorter BD were used for drying experiment.

  14. Thermodynamic analysis of fluidized bed drying of carrot cubes

    Energy Technology Data Exchange (ETDEWEB)

    Nazghelichi, Tayyeb; Kianmehr, Mohammad Hossein; Aghbashlo, Mortaza [Department of Agrotechnology, College of Abouraihan, University of Tehran, P.O. Box 33955-159, Pakdasht (Iran, Islamic Republic of)

    2010-12-15

    In this study, the energy and exergy analyses of fluidized bed drying of carrot cubes were investigated. Drying experiments were conducted at inlet air temperatures of 50, 60, and 70 C, BD (bed depths) of 30, 60, and 90 mm and square-cubed carrot dimensions of 4, 7, and 10 mm. The effects of drying variables on energy utilization, energy utilization ratio, exergy loss and exergy efficiency were studied. The energy utilization and energy utilization ratio varied between 0.105-1.949 kJ/s and 0.074-0.486, respectively. The exergy loss and exergy efficiency were found to be in the range of 0.206-1.612 kJ/s and 0.103-0.707, respectively. The results showed that small particles, deep beds and high inlet air temperatures increased energy utilization, energy utilization ratio, and exergy loss due to high value of heat and mass transfer. Also, the exergy efficiency had maximum value when higher drying air temperature, larger CS (cube size) and shorter BD were used for drying experiment. (author)

  15. Development of second-generation pressurized fluidized bed combustion process

    Energy Technology Data Exchange (ETDEWEB)

    Wolowodiuk, W.; Robertson, A. [Foster Wheeler Development Corp., Livingston, NJ (United States); Bonk, D. [Dept. of Energy, Morgantown, WV (United States)

    1995-12-01

    Under the sponsorship of the United States Department of Energy, Foster Wheeler Development Corporation, and its team members, Westinghouse, Gilbert/Commonwealth, and the Institute of Gas Technology are developing second-generation pressurized fluidized bed combustion technology capable of achieving net plant efficiency in excess of 45 percent based on the higher heating value of the coal. A three-phase program entails design and costing of a 500 MWe power plant and identification of developments needed to commercialize this technology (Phase 1), testing of individual components (Phase 2), and finally testing these components in an integrated mode (Phase 3). This paper briefly describes the results of the first two phases as well as the progress on the third phase. Since other projects which use the same technology are in construction or in negotiation stages-namely, the Power System Development Facility and the Four Rivers Energy Modernization Projects-brief descriptions of these are also included.

  16. Computational Fluid Dynamics Simulation of Fluidized Bed Polymerization Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Fan, Rong [Iowa State Univ., Ames, IA (United States)

    2006-01-01

    Fluidized beds (FB) reactors are widely used in the polymerization industry due to their superior heat- and mass-transfer characteristics. Nevertheless, problems associated with local overheating of polymer particles and excessive agglomeration leading to FB reactors defluidization still persist and limit the range of operating temperatures that can be safely achieved in plant-scale reactors. Many people have been worked on the modeling of FB polymerization reactors, and quite a few models are available in the open literature, such as the well-mixed model developed by McAuley, Talbot, and Harris (1994), the constant bubble size model (Choi and Ray, 1985) and the heterogeneous three phase model (Fernandes and Lona, 2002). Most these research works focus on the kinetic aspects, but from industrial viewpoint, the behavior of FB reactors should be modeled by considering the particle and fluid dynamics in the reactor. Computational fluid dynamics (CFD) is a powerful tool for understanding the effect of fluid dynamics on chemical reactor performance. For single-phase flows, CFD models for turbulent reacting flows are now well understood and routinely applied to investigate complex flows with detailed chemistry. For multiphase flows, the state-of-the-art in CFD models is changing rapidly and it is now possible to predict reasonably well the flow characteristics of gas-solid FB reactors with mono-dispersed, non-cohesive solids. This thesis is organized into seven chapters. In Chapter 2, an overview of fluidized bed polymerization reactors is given, and a simplified two-site kinetic mechanism are discussed. Some basic theories used in our work are given in detail in Chapter 3. First, the governing equations and other constitutive equations for the multi-fluid model are summarized, and the kinetic theory for describing the solid stress tensor is discussed. The detailed derivation of DQMOM for the population balance equation is given as the second section. In this section

  17. Pyrolysis of Softwood Carbohydrates in a Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    Dmitry Yu. Murzin

    2008-09-01

    Full Text Available In the present work pyrolysis of pure pine wood and softwood carbohydrates, namely cellulose and galactoglucomannan (the major hemicellulose in coniferous wood, was conducted in a batch mode operated fluidized bed reactor. Temperature ramping (5°C/min was applied to the heating until a reactor temperature of 460 °C was reached. Thereafter the temperature was kept until the release of non-condensable gases stopped. The different raw materials gave significantly different bio-oils. Levoglucosan was the dominant product in the cellulose pyrolysis oil. Acetic acid was found in the highest concentrations in both the galactoglucomannan and in the pine wood pyrolysis oils. Acetic acid is most likely formed by removal of O-acetyl groups from mannose units present in GGM structure.

  18. Natural gas combustion in a catalytic turbulent fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Foka, M.; Chaouki, J.; Guy, C.; Klvana, D. [Ecole Polytechnique de Montreal, Quebec (Canada). Dept. of Chemical Engineering

    1994-12-01

    Catalytic fluidized bed combustion of natural gas is shown to be an emerging technology capable of meeting all environmental constraints as far as nitrogen oxides and carbon monoxide are concerned. This technology uses powder catalysts in the turbulent flow regime where the gas-solid contact is optimal so as to maintain a high combustion efficiency. In fact, the catalytic combustion carried out in both the bubbling and the turbulent regimes at 450-500{sup o}C shows that the turbulent regime is more favorable. A single phase plug flow model with axial dispersion is shown to fit satisfactorily the data obtained at 500{sup o}C where the combustion efficiency is very good. A self-sustained combustion was achieved with a mixture of 4% methane at around 500{sup o}C with a complete conversion of methane and a zero emission of NO{sub x} and CO. (author)

  19. Heat flux distribution on circulating fluidized bed boiler water wall

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The future of circulating fluidized bed (CFB)combustion technology is in raising the steam parameters to supercritical levels.Understanding the heat flux distribution on the water wall is one of the most important issues in the design and operation of supercritical pressure CFB boilers.In the present paper,the finite element analysis (FEA) method is adopted to predict the heat transfer coefficient as well as the heat flux of the membrane wall and the results are validated by direct measurement of the temperature around the tube.Studies on the horizontal heat flux distribution were conducted in three CFB boilers with different furnace size,tube dimension and water temperature.The results are useful in supercritical pressure CFB boiler design.

  20. Bubbling fluidized bed boiler for Vanaja power plant

    Energy Technology Data Exchange (ETDEWEB)

    Sormunen, R.; Haermae, P.; Vessonen, K.; Ketomaeki, A. [ed.

    1998-07-01

    At the Vanaja Power Plant, on the outskirts of Haemeenlinna, there have been changes which reflect the central goals in IVO`s product development work. At Vanaja, efficiency is combined with environmental friendliness. In the early 1980s, the plant was modernized to produce district heat in addition to electricity. At that time, along with the new gas turbine at the plant, the main fuel, coal, while remaining the fuel for the old boilers, was replaced by natural gas. This year a new type of bubbling fluidized bed boiler enabling continuous use of peat and trial use of biofuels along with coal was introduced at the plant. In addition to the Nordic countries, this kind of technology is required in central eastern Europe, where modernization of ageing power plants is being planned to achieve the best possible solutions in respect of production and the environment. IVO develops a new repair technique for underwater sites

  1. Continuous fluidized-bed contactor with recycle of sorbent

    Science.gov (United States)

    Scott, Charles D.; Petersen, James N.; Davison, Brian H.

    1996-01-01

    A continuous fluidized-bed contactor containing sorbent particles is used to remove solutes from liquid solvents. As the sorbent particles, for example gel beads, sorb the solute, for example metal ion species, the sorbent particles tend to decrease in diameter. These smaller loaded sorbent particles rise to the top of the contactor, as larger sorbent particles remain at the bottom of the contactor as a result of normal hydraulic forces. The smaller loaded sorbent particles are then recovered, regenerated, and reintroduced into the contactor. Alternatively, the loaded sorbent particles may also slightly increase in diameter, or exhibit no change in diameter but an increase in density. As a result of normal hydraulic forces the larger loaded sorbent particles fall to the bottom of the contactor. The larger loaded sorbent particles are then recovered, regenerated, and reintroduced into the contactor.

  2. Nucla circulating atmospheric fluidized bed demonstration project. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-10-01

    Colorado-Ute Electric Association began a study to evaluate options for upgrading and extending the life of its Nucla power station in 1982. Located in southwestern Colorado near the town of Nucla, this station was commissioned in 1959 with a local bituminous coal as its design fuel for three identical stoker-fired units, each rated at 12.6 MW(e). Poor station efficiency, high fuel costs, and spiraling boiler maintenance costs forced the Nucla Station into low priority in the CUEA dispatch order as early as 1981. Among the options CUEA considered was to serve as a host utility to demonstrate Atmospheric Fluidized Bed Combustion (AFBC) technology. The anticipated environmental benefits and apparent attractive economics of a circulating AFBC led to Colorado-Ute`s decision to proceed with the design and construction of a demonstration project in 1984 at the Nucla facility.

  3. Hot-gas filtration for pressurized fluidized-bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Chang, R.; Kuby, W.

    1984-03-01

    This topical report discusses the status of the work, conducted under EPRI contract 1336-4, on the evaluation and development of ceramic filter hot gas cleanup technology for pressurized fluidized bed combustion. This topical report represents the status of the work through September 1983. The goal of the effort is to achieve 6000 h of operation on a 13-filter durability test rig. The work includes two parallel tasks. The first is construction of a durability test facility, operation of the facility with an initial candidate filter media installed, and assessment of results. The second task includes a literature survey to identify state-of-the-art ceramic fibers suitable for high-temperature gas filtration applications and filter testing in a single-filter test facility to assess the performance of promising new filter media. The best candidate will be chosen for further evaluation in the durability facility.

  4. Staged fluidized-bed coal combustor for boiler retrofit

    International Nuclear Information System (INIS)

    The Advanced Staged Fluidized-Bed Coal Combustion System (ASC) is a novel clean coal technology for either coal-fired repowering of existing boilers or for incremental power generation using combined-cycle gas turbines. This new technology combines staged combustion for gaseous emission control, in-situ sulfur capture, and an ash agglomeration/vitrification process for the agglomeration/vitrification of ash and spent sorbent, thus rendering solid waste environmentally benign. The market for ASC is expected to be for clean coal-fired repowering of generating units up to 250 MW, especially for units where space is limited. The expected tightening of the environmental requirements on leachable solids residue by-products could considerably increase the marketability for ASC. ASC consists of modular low-pressure vessels in which coal is partially combusted and gasified using stacked fluidized-bed processes to produce low-to-medium-Btu, high-temperature gas. This relatively clean fuel gas is used to repower/refuel existing pulverized-coal, natural gas, or oil-fired boilers using bottom firing and reburning techniques. The benefits of ASC coal-fired repowering include the ability to repower boilers without obtaining additional space while meeting the more stringent environmental requirements of the future. Low NOx, SOx, and particulate levels are expected while a nonleachable solid residue with trace metal encapsulation is produced. ASC also minimizes boiler modification and life-extension expenditures. Repowered efficiencies can be restored to the initial operating plant efficiency, and the existing boiler capacity can be increased by 10%. Preliminary cost estimates indicate that ASC will have up to a $250/kW capital cost advantage over existing coal-fired repowering options. 4 figs., 4 tabs

  5. Start-up and Performance of a Novel Reactor-Jet Biogas Inter-loop Anaerobic Fluidized Bed%一种新型反应器——生物气射流循环厌氧流化床的启动与运行特性

    Institute of Scientific and Technical Information of China (English)

    邓志毅; 韦朝海; 周秀峰

    2008-01-01

    A novel anaerobic reactor, jet biogas inter-loop anaerobic fluidized bed (JBILAFB), was designed and constructed. The start-up and performance of the reactor was investigated in the process of artificial glucose waste-water treatment. With the wastewater recycle ratio of 2.5:1, the recycled wastewater with biogas could mix sludge and wastewater in the JBILAFB reactor completely. The start-up of the JBILAFB reactor could be completed in less than 70 d through maintenance of hydraulic retention time (HRT) and stepwise increase of feed total organic carbon (TOC) concentration. After the start-up, with the volumetric TOC loadings of 14.3 kg·m-3·d-1 the TOC removal ra-tio, the effluent pH, and the volatile fatty acids (VFA)/alkalinity of the JBILAFB reactor were more than 80%, close to 7.0 and less than 0.4, respectively. Moreover, CH4 was produced at more than 70% of the theoretical value. The reactor exhibited high stability under the condition of high volumetric TOC loading. Sludge granules in the JBI-LAFB reactor were developed during the start-up and their sizes were enlarged with the stepwise increase of volu-metric TOC loadings from 0.8 kg·m-3·d-1 to 14.3 kg·m-3·d-1. Granules, an offwhite color and a similar spherical shape, were mainly comprised of global-like bacteria. These had good methanogenic activity and settleability,which were formed probably through adhesion of the bacteria. Some inorganic metal compounds such as Fe, Ca,Mg, Al, etc. were advantageous to the formation of the granules.

  6. Wavelet analysis of pressure fluctuation signals in a gas-solid fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    It has been shown that much dynamic information is hidden in the pressure fluctuation signals of a gas-solid fluidized bed. Unfortunately, due to the random and capricious nature of this signal, it is hard to realize reliable analysis using traditional signal processing methods such as statistical analysis or spectral analysis, which is done in Fourier domain. Information in different frequency band can be extracted by using wavelet analysis. On the evidence of the composition of the pressure fluctuation signals, energy of low frequency (ELF) is proposed to show the transition of fluidized regimes from bubbling fluidization to turbulent fluidization. Plots are presented to describe the fluidized bed's evolution to help identify the state of different flow regimes and provide a characteristic curve to identify the fluidized status effectively and reliably.

  7. Motion analysis of waste rock in gas-solids fluidized bed in coal dry beneficiation

    Institute of Scientific and Technical Information of China (English)

    郭迎福; 陈安华; 张永忠; 邓志鹏; 毛树楷

    2002-01-01

    Through the analysis of forces acting on the waste rock in the gas-solid fluidized bed, the waste rock velocity equations and displacement equations in the gas-solids fluidized bed were achieved and the influential factors of the waste rock motion in the fluidized bed were studied in this paper. The conclusions show that the primary factors influencing the waste rock motion are the waste rock grain size and the scraper velocity according to the computer simulation. This has provided the theoretical foundation both for improving the separating effect and ascertaining the length of the separating cell.

  8. An experimental study of the effect of collision properties on spout fluidized bed dynamics

    OpenAIRE

    Buijtenen, van, M.S.; Börner, Matthias; Deen, Niels G.; Heinrich, Stefan; Antonyuk, Sergiy; Kuipers, J.A.M.

    2009-01-01

    In this paper we experimentally study the effect of collision properties of different particle systems on the bed dynamics of a spout fluidized bed. This is done in different flow regimes: the spout-fluidization regime (case A), the jet-in-fluidized-bed regime (case B) and the spouting-with-aeration regime (case C). The considered particle systems comprise glass beads, γ-alumina oxide and zeolite 4A particles, which are all classified as Geldart D. A non-intrusive measurement technique is use...

  9. Removal of dust from flue gas in magnetically stabilized fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Yinghui Wang; Keting Gui; Mingheng Shi; Changfeng Li

    2008-01-01

    A magnetically stabilized fluidized bed (MSFB, φ 500mm x 2100mm) was designed to study dust removal from flue gas. Based on the mechanism of dust removal in a fixed bed, the effects on collection efficiency of magnetic field intensity, ratio of flue gas velocity to minimum fluidization velocity, bed height, and particle average diameter, were investigated. Then feasible methods for MSFB to better remove dust were proposed. Over 95% of dust removal with MSFB can be achieved, when stable fluidization is maintained and when magnetic particles are frequently renewed.

  10. Bioreactors with Light-Beads Fluidized Bed: The Voidage Function and its Expression

    Directory of Open Access Journals (Sweden)

    Iliev Vasil

    2014-12-01

    Full Text Available Light-beads fluidized bed bioreactors with gel particles are an attractive alternative for the implementation of a system with immobilized cells. They have a number of advantages: soft operating conditions, ability to work in an ideal mixing regime, intensification of heat- and mass transfer processes in the fermentation system. The expansion characteristics of the fluidized bed were investigated in the present work. The fluidized bed expansion was described using the voidage function. It was found that the voidage can be described by nonlinear regression relationships and the regression coefficients were a function of the particles parameters.

  11. Fluidized bed spray granulation: analysis of heat and mass transfers and dynamic particle populations

    Directory of Open Access Journals (Sweden)

    S. Heinrich

    2005-06-01

    Full Text Available A model was developed taking into consideration the heat and mass transfer processes in liquid-sprayed fluidized beds. Such fluidized beds (FB are used for granulation, coating and agglomeration. Conclusions are drawn on the relevance of particle dispersion, spraying and drying to temperature and concentrations distributions. In extension, the model was coupled with a population balance model to describe the particle size distribution and the seeds formation for continuous external FBSG (fluidized bed spray granulation with non-classifying product discharge and a screening and milling unit in the seeds recycle. The effects of seeds formation on the stability of the process is discussed.

  12. The impact of bed temperature on heat transfer characteristic between fluidized bed and vertical rifled tubes

    Science.gov (United States)

    Blaszczuk, Artur; Nowak, Wojciech

    2016-10-01

    In the present work, the heat transfer study focuses on assessment of the impact of bed temperature on the local heat transfer characteristic between a fluidized bed and vertical rifled tubes (38mm-O.D.) in a commercial circulating fluidized bed (CFB) boiler. Heat transfer behavior in a 1296t/h supercritical CFB furnace has been analyzed for Geldart B particle with Sauter mean diameter of 0.219 and 0.246mm. The heat transfer experiments were conducted for the active heat transfer surface in the form of membrane tube with a longitudinal fin at the tube crest under the normal operating conditions of CFB boiler. A heat transfer analysis of CFB boiler with detailed consideration of the bed-to-wall heat transfer coefficient and the contribution of heat transfer mechanisms inside furnace chamber were investigated using mechanistic heat transfer model based on cluster renewal approach. The predicted values of heat transfer coefficient are compared with empirical correlation for CFB units in large-scale.

  13. Heat Transfer in Segregated Fluidized Beds Part 2: Particle Motion and Its Effects on the Heat transfer in the Segregated Fluidized Beds

    Science.gov (United States)

    Gu, Yihua; Satoh, Isao; Saito, Takushi; Kawaguchi, Tatsuya

    In our previous paper, particle and temperature segregations in a fluidized bed of binary particle mixtures were experimentally examined, and heat transfer in the segregated fluidized bed was investigated. As the results, it was shown that the temperature segregation results mainly from low heat transfer coefficient through the interface layer, which exists between the flotsam-rich and jetsam-rich layers, and that the heat transfer coefficient increases rapidly with increasing the excess gas velocity. Following our previous paper, particle motion in the segregated fluidized bed was experimentally investigated in this paper, in order to make quantitative discussion on the relation between the heat transfer coefficient and particle motion in the interface layer. In the experiment, the Particle Imaging Velocimetry (PIV) method was applied to study the concentration and motion of particles in the segregated fluidized bed. A modified solid circulation model was built up to model the particle motion in the segregated fluidized bed. The experiment results showed that the vertical particle exchange rate of the interface layer increases with the excess gas velocity, and that the vertical heat transfer coefficient through the interface layer is mainly determined by the average particle exchange rate in the interface layer. Variations of the apparent thermal conductivity at different height in the particle layers were also determined by the vertical variation of the particle exchange rate. It was shown that the heat transfer coefficient or the thermal conductivity in the interface layer is influenced by the densities and specific heat capacities of the particles.

  14. Influência da imobilização de biomassa e do tamanho da partícula na fluidodinâmica de um reator anaeróbio de leito fluidizado = The influence of immobilized biomass and particle size on the fluid dynamics of an anaerobic fluidized bed reactor

    Directory of Open Access Journals (Sweden)

    Flavio Bentes Freire

    2008-01-01

    Full Text Available O estudo da fluidodinâmica é muito comum em diversas áreas relacionadas com a engenharia química, tais como nos processos de secagem e nos reatores químicos. Entretanto, em reatores biológicos empregados no tratamento de águas residuárias, esses aspectos ainda necessitam de investigações mais aprofundadas. Deste modo, é fundamental avaliar a influência da presença do biofilme no comportamento fluidodinâmico do reator, por meio de importantes parâmetros como, por exemplo, a velocidade de mínima fluidização, a expansão, a porosidade do leito e a velocidade terminal da partícula. O objetivo deste trabalho foi realizar uma investigação da fluidodinâmica de um reator anaeróbio de leito fluidizado, tratando uma água residuária sintética preparada a partir da solução utilizada para determinação de DBO, tendo o carvão ativado como meio suportepara a imobilização de biomassa. Especificamente, no trabalho, verificou-se que a biomassa imobilizada aumentou a densidade das partículas e alterou os principais parâmetros fluidodinâmicos avaliados.Fluid dynamic analysis is an important branch of several chemical engineering related areas, such as drying processes and chemical reactors. However, aspects concerning fluid dynamics in wastewater treatment bioreactors still require further investigation, as they highly influence process efficiency. Therefore, it is essential to evaluate the influence of biofilm on the reactor fluid dynamicbehavior, through the analysis of a few important parameters, such as minimum fluidization velocity, bed expansion and porosity, and particle terminal velocity. The main objective of the present work was to investigate the fluid dynamics of an anaerobic fluidized bed reactor, having activated carbon particles as support media for biomass immobilization. Reactor performance was tested using synthetic residual water, which was prepared using the solution employed in BOD determination. The results

  15. Effect of a Reactivation strategy based on partial bio catalyst replacement on the performance of a fungal fluidized bed bioreactor

    Energy Technology Data Exchange (ETDEWEB)

    Ortega-Clemente, A.; Robledo-Narvaez, P.; Barrera-Cortes, J.; Poggi-Varaldo, H. M.

    2009-07-01

    The Mexican pulp and paper industry discharges approximately 12% of the annual industrial discharges and holds a second position in the ranking of main water industrial polluters in Mexico. Their wastewaters are characteristically recalcitrant and toxic. The objective of this work was to evaluate the effectiveness of two operational strategies on the performance of two fungal fluidized bed reactor (FBR) for the post-treatment of anaerobically weal black liquor systems (AP-WBL) without supplementation of soluble carbohydrates, i. e. Strategy 1 (continuous operation with the same original, fungal bio catalysts and eventual spikes of protease inhibitor and glucose), and Strategy 2 operation with partial exchange of bio catalysts. (Author)

  16. Experimental Study on Coal Multi-generation in Dual Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    Fan Xiaoxu; Lu Qinggang; Na Yongjie; Liu Qi

    2007-01-01

    An atmospheric test system of dual fluidized beds for coal multi-generation was built. One bubbling fluidized bed is for gasification and a circulating fluidized bed for combustion. The two beds are combined with two valves:one valve to send high temperature ash from combustion bed to the gasification bed and another valve to send char and ash from gasification bed to combustion bed. Experiments on Shenhua coal multi-generation were made at temperatures from 1112 K to 1191 K in the dual fluidized beds. The temperatures of the combustor are stable and the char combustion efficiency is about 98%. Increasing air/coal ratio to the fluidized bed leads to the increase of temperature and gasification efficiency. The maximum gasification efficiency is 36.7% and the calorific value of fuel gas is 10.7 MJ/Nm3. The tar yield in this work is 1.5%, much lower than that of pyrolysis.Carbon conversion efficiency to fuel gas and flue gas is about 90%.

  17. Gas-solid hydroxyethylation of potato starch in a stirred vibrating fluidized bed reactor

    NARCIS (Netherlands)

    Kuipers, N.J M; Stamhuis, Eize; Beenackers, A.A C M

    1996-01-01

    A novel reactor for modifying cohesive C-powders such as in the gas-solid hydroxyethylation of semidry potato starch is characterized, the so-called stirred vibrating fluidized bed reactor. Good fluidization characteristics are obtained in this reactor for certain combinations of stirring and vibrat

  18. INVESTIGATION INTO MALDISTRIBUTION IN A CIRCULATING FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Qingjie Guo; Joachim Werther; Ernst-Ulrich Hartge

    2003-01-01

    Experiments on maldistribution were conducted in a 8.5 m high, 1 m ×0.3 m cross-section circulating fluidized bed equipped with a 33 bubble-cap distributor. There exists an uneven distribution in flow rate, the bubble caps in the center region having larger flow rates than those next to the wall. Flow resistance has been found to be the dominating factor influencing gas flow rate distribution. Increasing superficial gas velocity improves flow rate distribution for a low pressure-drop distributor. For a high pressure-drop distributor, superficial gas velocity has little effect on flow rate distribution. A ratio of maximum flow rate through a bubble cap to average flow rate through all bubble caps (Vmax/Vav) characterizes the flow rate distribution. Distributor-to-bed pressure drop ratio (△Pd/△Pr) is another necessary parameter to achieve even flow distribution. A correlation between these two ratios is developed for predicting flow rate maldi stribution in CFB bubble-cap distributor.

  19. Sulfide oxidation in fluidized bed bioreactor using nylon support material

    Institute of Scientific and Technical Information of China (English)

    Varsha Midha; M K Jha; Apurba Dey

    2012-01-01

    A continuous fluidized bed bioreactor(FBBR)with nylon support particles was used to treat synthetic sulfide wastewater at different hydraulic retention time of 25,50 and 75 min and upflow velocity of 14,17 and 20 m/hr.The effects of upflow velocity,hydraulic retention time and reactor operation time on sulfide oxidation rate were studied using statistical model.Mixed culture obtained from the activated sludge,taken from tannery effluent treatment plant,was used as a source for microorganisms.The diameter and density of the nylon particles were 2-3 mm and 1140 kg/m3,respectively.Experiments were carried out in the reactor at a temperature of(30± 2)℃,at a fixed bed height of 16 cm after the formation of biofilm on the surface of support particles.Biofilm thickness reached(42±3)μm after 15 days from reactor start-up.The sulfide oxidation,sulfate and sulfur formation is examined at all hydraulic retention times and upflow velocities.The results indicated that almost 90%-92% sulfide oxidation was achieved at all hydraulic retention times.Statistical model could explain 94% of the variability and analysis of variance showed that upflow velocity and hydraulic retention time slightly affected the sulfide oxidation rate.The highest sulfide oxidation of 92% with 70% sulfur was obtained at hydraulic retention time of 75 min and upflow velocity of 14 m/hr.

  20. Fast Pyrolysis of Agricultural Wastes in a Fluidized Bed Reactor

    Science.gov (United States)

    Wang, X. H.; Chen, H. P.; Yang, H. P.; Dai, X. M.; Zhang, S. H.

    Solid biomass can be converted into liquid fuel through fast pyrolysis, which is convenient to be stored and transported with potential to be used as a fossil oil substitute. In China, agricultural wastes are the main biomass materials, whose pyrolysis process has not been researched adequately compared to forestry wastes. As the representative agricultural wastes in China, peanut shell and maize stalk were involved in this paper and pine wood sawdust was considered for comparing the different pyrolysis behaviors of agricultural wastes and forestry wastes. Fast pyrolysis experiments were carried out in a bench-scale fluidized-bed reactor. The bio-oil yieldsof peanut shell and maize stalk were obviously lower than that ofpine sawdust. Compared with pine sawdust, the char yields of peanut shell and maize stalk were higher but the heating value of uncondensable gaswas lower. This means that the bio-oil cost will be higher for agricultural wastes if taking the conventional pyrolysis technique. And the characteristic and component analysis resultsof bio-oil revealed that the quality of bio-oil from agricultural wastes, especially maize stalk, was worse than that from pine wood. Therefore, it is important to take some methods to improve the quality of bio-oilfrom agricultural wastes, which should promote the exploitation of Chinese biomass resources through fast pyrolysis in afluidized bed reactor.

  1. Attempts on cardoon gasification in two different circulating fluidized beds

    Directory of Open Access Journals (Sweden)

    Chr. Christodoulou

    2014-11-01

    Full Text Available Few tests have been carried out in order to evaluate the use of cardoon in gasification and combustion applications most of the researchers dealt with agglomeration problems. The aim of this work is to deal with the agglomeration problem and to present a solution for the utilization of this biofuel at a near industrial application scale. For this reason, two experiments were conducted, one in TU Delft and one in Centre for Research and Technology Hellas (CERTH, using fuel cardoon and 50% w/w cardoon blended with 50% w/w giant reed respectively. Both experimental campaigns were carried out in similar atmospheric circulating fluidized bed gasifiers. Apart from the feedstock, the other differences were the gasification medium and the bed material used in each trial. The oxidizing agent at TUD׳s run was O2/steam, whereas CERTH׳s tests used air. When experiments with the cardoon 50% w/w–giant reed 50% w/w blend were performed no agglomeration problems were presented. Consequently, gasification could be achieved in higher temperature than that of pure cardoon which led to the reduction of tar concentration.

  2. Peach and apricot stone combustion in a bubbling fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Kaynak, B.; Atimtay, Aysel T. [Department of Environmental Engineering, Middle East Technical University, Ankara 06531 (Turkey); Topal, H. [Department of Mechanical Engineering, Engineering and Architecture Faculty, Gazi University, Ankara 06570 (Turkey)

    2005-07-25

    In this study, a bubbling fluidized bed combustor (BFBC) of 102 mm inside diameter and 900 mm height was used to investigate the combustion characteristics of peach and apricot stones produced as a waste from the fruit juice industry. A lignite coal was also burned in the same combustor. The combustion characteristics of the wastes were compared with that of a lignite coal that is most widely used in Turkey. On-line concentrations of O{sub 2}, CO, CO{sub 2}, SO{sub 2}, NO{sub X} and total hydrocarbons (C{sub m}H{sub n}) were measured in the flue gas during combustion experiments. By changing the operating parameters (excess air ratio, fluidization velocity, and fuel feed rate), the variation of emissions of various pollutants was studied. Temperature distribution along the bed was measured with thermocouples. During the combustion tests, it was observed that the volatile matter from peach and apricot stones quickly volatilizes and mostly burn in the freeboard. The temperature profiles along the bed and the freeboard also confirmed this phenomenon. It was found that as the volatile matter of fruit stones increases, the combustion takes place more in the freeboard region. The results of this study have shown that the combustion efficiencies ranged between 98.8% and 99.1% for coal, 96.0% and 97.5% for peach stone and 93.4% and 96.3% for apricot stones. The coal has zero CO emission, but biomass fuels have very high CO emission which indicates that a secondary air addition is required for the system. SO{sub 2} emission of the coal is around 2400-2800 mg/Nm{sup 3}, whereas the biomass fuels have zero SO{sub 2} emission. NO{sub x} emissions are all below the limits set by the Turkish Air Quality Control Regulation of 1986 (TAQCR) for all tests. As the results of combustion of two biomass fuels are compared with each other, peach stones gave lower CO and NO{sub x} emissions but the SO{sub 2} emissions are a little higher than for apricot stones. These results suggest that

  3. Lignite air-steam gasification in the fluidized bed of iron-containing slag catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Shchipko, M.L.; Golovin, Yu. [Inst. of Chemistry of Natural Organic Materials, Academgorodok, Krasnoyarsk (Russian Federation)

    1995-12-01

    The influence of fluidized bed of iron-containing slag particles on air-steam gasification of powdered Kansk-Achinsk lignite in entrained flow was studied in pilot installation with productivity about 60 kg per hour. Slag of Martin process and boiler slag were used as catalytic active materials until their complete mechanical attrition. Two following methods of catalytic gasification of lignite were compared: the partial gasification in stationary fluidized bed of slag particles with degree of fuel conversion 40-70% and complete gasification in circulating bed of slag particles. In the first case only the most reactive part of fuel is gasified with the simultaneously formation of porous carbon residue with good sorption ability. It was found the catalytic fluidized bed improves heat transfer from combustion to reduction zone of gas-generator and increases the rate of fuel conversion at the temperature range 900-1000{degrees}C. At these temperatures the degree of conversion is depended considerably on the duration time of fuel particles in the catalytic fluidized bed. The influence of catalytic fluidized bed height and velocity of reaction mixture on the temperature profiles in the gas-generator was studied. The optimal relationship was found between the fluidized bed height and velocity of flow which makes possible to produce the gas with higher calorific value at maximum degree of fuel conversion.

  4. Bed agglomeration in fluidized combustor fueled by wood and rice straw blends

    NARCIS (Netherlands)

    Thy, P.; Jenkins, B.M.; Williams, R.B.; Lesher, C.E.; Bakker, R.R.

    2010-01-01

    Petrographic techniques have been used to examine bed materials from fluidized bed combustion experiments that utilized wood and rice straw fuel blends. The experiments were conducted using a laboratory-scale combustor with mullite sand beds, firing temperatures of 840 to 1030 °C, and run durations

  5. Modeling N2O Reduction and Decomposition in a Circulating Fluidized bed Boiler

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Åmand, Lars-Erik; Dam-Johansen, Kim;

    1996-01-01

    The N2O concentration was measured in a circulating fluidized bed boiler of commercial size. Kinetics for N2O reduction by char and catalytic reduction and decomposition over bed material from the combustor were determined in a laboratory fixed bed reactor. The destruction rate of N2O in the comb...

  6. Performances of continuous dryer with inert medium fluidized bed

    Directory of Open Access Journals (Sweden)

    Arsenijević Zorana Lj.

    2008-01-01

    Full Text Available A fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies according to the main efficiency criteria, i.e. specific water evaporation rate, specific heat consumption and speci­fic air consumption. A high drying efficiency results from the large con­tact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles leads to nearly isothermal conditions throughout the bed. A fluid bed dryer with inert particles was used for drying of slurries. Experiments were performed in a cylindrical column 215 mm in diameter with glass spheres as inert particles. In this paper, results of drying experi­ments with slurries of Zineb fungicide, copper hydroxide, calcium carbo­nate and pure water used as the feed material are presented. In our fluidized bed we successfully dried a number of other materials such as: fungicides and pesticides (Ziram, Propineb, Mangozeb, copper oxy-chloride, copper oxy-sulphate, Bordeaux mixture, other inorganic compounds (calcium sulphate, cobalt carbonate, electrolytic copper, sodium chloride, and a complex compound (organo-bentonite. The effects of operating conditions on dryer throughput and product quality were investigated. Main performance criteria, i.e. specific water evaporation rate, specific heat consumption and specific air consumption, were quantified. Temperature profile along the bed was mapped, and nearly isothermal conditions were found due to thorough mixing of the particles. Analysis of drying and energy efficiencies as a function of inlet and outlet air temperature difference was performed for deeper insight in dryer behavior and for optimizing dryer design and operation from an energy point of view. A simple mathematical model based on an overall heat balance predicts the dryer performance quite well. The industrial prototype with fluid bed of 0.8 m in diameter and capacity 650 kg of evaporated moisture per

  7. Effects of Immersed Surfaces on the Combustor Efficiency of Small-Scale Fluidized Beds

    Directory of Open Access Journals (Sweden)

    Nurdil Eskin

    2005-09-01

    Full Text Available In this study, effects of the different types of heat exchanger surfaces on the second law efficiency of a small-scale circulating fluidized bed (CFB combustor are analyzed and the results are compared with the bubbling fluidized bed coal combustor effectiveness values. Using a previously developed simulation program, combustor efficiency and entropy generation values are obtained at different operation velocities at different height and volume ratios of the immersed surfaces, both for circulating and bubbling fluidized bed combustors. Besides that, the influence of the immersed surface types on the combustor efficiency was compared for different fluidized bed combustors. Through this analysis, the dimensions, arrangement and type of the immersed surfaces which achieve maximum efficiency are obtained.

  8. DISCRETE PARTICLE SIMULATION OF SIZE SEGREGATION OF PARTICLE MIXTURES IN A GAS FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Y. Q. Feng; A. B. Yu

    2006-01-01

    This paper presents a study of the mixing/segregation behaviour of particle mixtures in a gas fluidized bed by use of the discrete particle simulation. Spherical particles with diameters 2 mm (jetsam) and 1 mm (flotsam) and density 2 500 kg·m-3 are used as solid mixtures with different volume fractions. The particles are initially packed uniformly in a rectangular bed and then fluidized by gas uniformly injected at the bottom of the bed. The gas injection velocities vary to cover fixed, partially and fully fluidized bed conditions. Segregation/mixing behaviour is discussed in terms of flow patterns, solid concentration profile and mixing kinetics. The results show that segregation, as a transient fluidization process, is strongly affected by gas injection velocities for a given particle mixture. With the increase of the volume fraction of flotsam, size segregation appears at lower velocities.

  9. Olive cake combustion in a circulating fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Huseyin Topal; Aysel T. Atimtay; Ali Durmaz [Gazi University, Ankara (Turkey). Department of Mechanical Engineering, Engineering and Architecture Faculty

    2003-06-01

    In this study, a circulating fluidized bed of 125 mm diameter and 1800 mm height was used to find the combustion characteristics of olive cake (OC) produced in Turkey. A lignite coal that is most widely used in Turkey was also burned in the same combustor. The combustion experiments were carried out with various excess air ratios. The excess air ratio, {lambda} has been changed between 1.1 and 2.16. Temperature distribution along the bed was measured with thermocouples. On-line concentrations of O{sub 2}, SO{sub 2}, CO{sub 2}, CO, NOx and total hydrocarbons were measured in the flue gas. Combustion efficiencies of OC and lignite coal are calculated, and the optimum conditions for operating parameters are discussed. The combustion efficiency of OC changes between 82.25 and 98.66% depending on the excess air ratio. There is a sharp decrease observed in the combustion losses due to hydrocarbons and CO as the excess air ratio increases. The minimum emissions are observed at {lambda} = 1.35. Combustion losses due to unburned carbon in the bed material do not exceed 1.4 wt% for OC and 1.85 wt% for coal. The combustion efficiency for coal changes between 82.25 and 98.66% for various excess air ratios used in the study. The ash analysis for OC is carried out to find the suitability of OC ash to be used as fertilizer. The ash does not contain any hazardous metal. 7 refs., 10 figs., 6 tabs.

  10. Insights in hydrodynamics of bubbling fluidized beds at elevated pressure by DEM-CFD approach

    Institute of Scientific and Technical Information of China (English)

    Zahra Mansourpour; Sedighe Karimi; Reza Zarghami; Navid Mostoufi; Rahmat Sotudeh-Gharebagh

    2010-01-01

    A numerical simulation was conducted to study the effect of pressure on bubble dynamics in a gas-solid fluidized bed. The gas flow was modeled using the continuum theory and the solid phase, by the dis-crete element method (DEM). To validate the simulation results, calculated local pressure fluctuations were compared with corresponding experimental data of 1-mm polyethylene particles. It was shown that the model successfully predicts the hydrodynamic features of the fluidized bed as observed in the experiments. Influence of pressure on bubble rise characteristics such as bubble rise path, bubble sta-bility, average bubbles diameter and bubble velocity through the bed was investigated. The simulation results are in conformity with current hydrodynamic theories and concepts for fluidized beds at high pressures. The results show further that elevated pressure reduces bubble growth, velocity and stability and enhances bubble gyration through the bed, leading to change in bed flow structure.

  11. Fluidized-bed combustion process evaluation and program support. Quarterly report, January-March 1980

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, I.; Podolski, W.F.; Swift, W.M.; Henry, R.F.; Hanway, J.E.; Griggs, K.E.; Herzenberg, C.; Helt, J.E.; Carls, E.L.

    1980-12-01

    Argonne National Laboratory is undertaking several tasks primarily in support of the pressurized fluidized-bed combustion project management team at Morgantown Energy Technology Center. Work is under way to provide fluidized-bed combustion process evaluation and program support to METC, determination of the state of the art of instrumentation for FBC applications, evaluation of the performance capability of cyclones for hot-gas cleaning in PFBC systems, and an initial assessment of methods for the measurement of sodium sulfate dew point.

  12. Design of a fluidized bed incinerator to process organic solid waste

    OpenAIRE

    Salvatore La Verde Spano; Leonardo Taylhardat

    2015-01-01

    This work includes the theoretical design of a fluidized bed incinerator for organic waste disposal, according with the most advanced parameters published about the subject, taking into account the regulations provided for this type of equipment and related environment. Current designs of incinerators and fluidized bed gasifiers proved to be mostly cylindrical. The design element to which greater importance is ascribed to the incinerator operating temperature and residence time of the waste i...

  13. Sorption-enhanced steam methane reforming in fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Johnsen, Kim

    2006-10-15

    Hydrogen is considered to be an important potential energy carrier; however, its advantages are unlikely to be realized unless efficient means can be found to produce it without generation of CO{sub 2}. Sorption-enhanced steam methane reforming (SE-SMR) represent a novel, energy-efficient hydrogen production route with in situ CO{sub 2} capture, shifting the reforming and water gas shift reactions beyond their conventional thermodynamic limits. The use of fluidized bed reactors for SE-SMR has been investigated. Arctic dolomite, a calcium-based natural sorbent, was chosen as the primary CO{sub 2}-acceptor in this study due to high absorption capacity, relatively high reaction rate and low cost. An experimental investigation was conducted in a bubbling fluidized bed reactor of diameter 0.1 m, which was operated cyclically and batch wise, alternating between reforming/carbonation conditions and higher-temperature calcination conditions. Hydrogen concentrations of >98 mole% on a dry basis were reached at 600 C and 1 atm, for superficial gas velocities in the range of {approx}0.03-0.1 m/s. Multiple reforming-regeneration cycles showed that the hydrogen concentration remained at {approx}98 mole% after four cycles. The total production time was reduced with an increasing number of cycles due to loss of CO{sub 2}-uptake capacity of the dolomite, but the reaction rates of steam reforming and carbonation seemed to be unaffected for the conditions investigated. A modified shrinking core model was applied for deriving carbonation kinetics of Arctic dolomite, using experimental data from a novel thermo gravimetric reactor. An apparent activation energy of 32.6 kj/mole was found from parameter fitting, which is in good agreement with previous reported results. The derived rate expression was able to predict experimental conversion up to {approx}30% very well, whereas the prediction of higher conversion levels was poorer. However, the residence time of sorbent in a continuous

  14. A fluidized bed selective emitter system driven by a non-premixed burner

    Science.gov (United States)

    Ortabasi, U.; Lund, K. O.; Seshadri, K.

    1996-02-01

    One of the key priorities in the development of Thermophotovoltaic power technology is a highly efficient heat-source/emitter system that is robust and stable. This paper describes a tightly coupled burner/selective emitter combination that integrates two novel concepts that are now under development: A fluidized bed emitter that consists of hollow, submillimeter spheres as the sources of radiant energy and a non-premixed, self regulating burner. The rationale behind the proposed system is to combine the unique intrinsic features of both concepts to provide the TPV community with an enabling technology. The fluidized bed provides excellent heat transfer, temperature uniformity, high radiant power density, reduced substrate and combustion background, robustness, thermal shock resistance, minimal contamination, and long operational life. The paper discusses a fluidized bed system that consists of selectively emitting, hollow Ho-YAG spheres with 500 micron diameter and 10-100 micron shell thickness operating at 1500 K. Key issues related to heat transfer and radiation transport in the fluidized bed are analyzed. The collective emitter efficiency and power density of a fluidized bed are discussed. The non-premixed burner achieves very high temperatures, has a low emission in toxic byproducts, provides self regulating stability, eliminates flashback hazards, and is operable with hydrogen. The paper concludes with a description of a complete fluidized bed TPV system including an elliptic/parabolic transfer optics and a photovoltaic cavity converter that boosts the flux density received by the photovoltaic cells.

  15. COMPARISON OF UASB AND FLUIDIZED-BED REACTORS FOR SULFATE REDUCTION

    Directory of Open Access Journals (Sweden)

    S. M. Bertolino

    2015-03-01

    Full Text Available Abstract Reactor hydrodynamics is important for sulfidogenesis because sulfate reduction bacteria (SRB do not granulate easily. In this work, the sulfate reduction performance of two continuous anaerobic bioreactors was investigated: (i an upflow anaerobic sludge blanket (UASB reactor and (ii a fluidized bed reactor (FBR. Organic loading, sulfate reduction, and COD removal were the main parameters monitored during lactate and glycerol degradation. The UASB reactor with biomass recirculation showed a specific sulfate reduction rate of 0.089±0.014 g.gSSV-1.d-1 (89% reduction, whereas values twice as high were achieved in the FBR treating either lactate (0.200±0.017 g.gSSV-1.d-1 or glycerol (0.178±0.010 g.gSSV-1.d-1. Sulfate reduction with pure glycerol produced a smaller residual COD (1700 mg.L-1 than that produced with lactate (2500 mg.L-1 at the same COD.sulfate-1 mass ratio. It was estimated that 50% of glycerol degradation was due to sulfate reduction and 50% to fermentation, which was supported by the presence of butyrate in the FBR effluent. The UASB reactor was unable to produce effluents with sulfate concentrations below 250 mg.L-1 due to poor mixing conditions, whereas the FBR consistently ensured residual sulfate concentrations below such a value.

  16. Explosion protection in fluidized beds; Explosionsschutz an Wirbelschichtanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Siwek, R. [FireEx Consultant GmbH, Giebenach (Switzerland)

    2002-09-01

    Measures for preventive and constructive explosion protection of fluidized bed systems were first published in 'Sicherheitsregeln fuer den Explosionsschutz bei der Konstruktion und Errichtung von Wirbelschicht-sprueh-granulatoren, Wirbelschichttrocknern, Wirbelschicht-Coatinganlagen' by Hauptverband der gewerblichen Berufsgenossenschaften. The authors stressed the importance of constant updating. In 1997, the VDI Kommission Reinhaltung der Luft started to work on the update of VDI 2263 No.5. This guideline 'Staubbraende und Staubexplosionen Gefahren - Beurteilung - Schutzmassnahmen, Explosionsschutz bei Wirbelschichtanlagen' was published as a draft version in March 2002. A supplement, No. 5.1, was published as a draft version in October 2002; it presents examples of risk assessments and protective measures and requires knowledge of VDI 2263 No. 5. This contribution summarizes specifications of hazards in fluidized beds when working withe burnable dust/air mixtures, vapour/air mixtures, or hybrid mixtures. Further, improvements of constructive explosion protection measures are pointed out, and the limits of application of the two VDI regulations are compared. [German] In den 'Sicherheitsregeln fuer den Explosionsschutz bei der Konstruktion und Errichtung von Wirbelschicht - Sprueh - Granulatoren, Wirbelschichttrocknern, Wirbelschicht - Coatinganlagen' des Hauptverbandes der gewerblichen Berufsgenossenschaften [1] wurden erstmalig Massnahmen des vorbeugenden und konstruktiven Explosionsschutzes an Wirbelschichtanlagen entsprechend dem damaligen Wissenstand zusammenfassend dargestellt. Die Verfasser wiesen aber bereits damals darauf hin, dass die Wirkung solcher Sicherheitsregeln auf Dauer nur dann gewaehrleistet sind, wenn sie durch weitere Erkenntnisse aus der fortschreitenden Entwicklung immer wieder ergaenzt werden. Im Jahre 1997 wurde durch die VDI-Kommission Reinhaltung der Luft die erste Sitzung zur Novellierung der Richtlinie VDI

  17. Modeling moisture diffusivity, activation energy and specific energy consumption of squash seeds in a semi fluidized and fluidized bed drying.

    Science.gov (United States)

    Chayjan, Reza Amiri; Salari, Kamran; Abedi, Qasem; Sabziparvar, Ali Akbar

    2013-08-01

    This study investigated thin layer drying of squash seeds under semi fluidized and fluidized bed conditions with initial moisture content about 83.99% (d.b.). An experimental fluidized bed dryer was also used in this study. Air temperature levels of 50, 60, 70 and 80 °C were applied in drying samples. To estimate the drying kinetic of squash seed, seven mathematical models were used to fit the experimental data of thin layer drying. Among the applied models, Two-term model has the best performance to estimate the thin layer drying behavior of the squash seeds. Fick's second law in diffusion was used to determine the effective moisture diffusivity of squash seeds. The range of calculated values of effective moisture diffusivity for drying experiments were between 0.160 × 10(-9) and 0.551 × 10(-10) m(2)/s. Moisture diffusivity values decreased as the input air temperature decreased. Activation energy values were found to be between 31.94 and 34.49 kJ/mol for 50 °C to 80 °C, respectively. The specific energy consumption for squash seeds was calculated at the boundary of 0.783 × 10(6) and 2.303 × 10(6) kJ/kg. Increasing in drying air temperature in different bed conditions led to decrease in specific energy value. Results showed that applying the semi fluidized bed condition is more effective for convective drying of squash seeds. The aforesaid drying characteristics are useful to select the best operational point of fluidized bed dryer and to precise design of system.

  18. Modeling moisture diffusivity, activation energy and specific energy consumption of squash seeds in a semi fluidized and fluidized bed drying.

    Science.gov (United States)

    Chayjan, Reza Amiri; Salari, Kamran; Abedi, Qasem; Sabziparvar, Ali Akbar

    2013-08-01

    This study investigated thin layer drying of squash seeds under semi fluidized and fluidized bed conditions with initial moisture content about 83.99% (d.b.). An experimental fluidized bed dryer was also used in this study. Air temperature levels of 50, 60, 70 and 80 °C were applied in drying samples. To estimate the drying kinetic of squash seed, seven mathematical models were used to fit the experimental data of thin layer drying. Among the applied models, Two-term model has the best performance to estimate the thin layer drying behavior of the squash seeds. Fick's second law in diffusion was used to determine the effective moisture diffusivity of squash seeds. The range of calculated values of effective moisture diffusivity for drying experiments were between 0.160 × 10(-9) and 0.551 × 10(-10) m(2)/s. Moisture diffusivity values decreased as the input air temperature decreased. Activation energy values were found to be between 31.94 and 34.49 kJ/mol for 50 °C to 80 °C, respectively. The specific energy consumption for squash seeds was calculated at the boundary of 0.783 × 10(6) and 2.303 × 10(6) kJ/kg. Increasing in drying air temperature in different bed conditions led to decrease in specific energy value. Results showed that applying the semi fluidized bed condition is more effective for convective drying of squash seeds. The aforesaid drying characteristics are useful to select the best operational point of fluidized bed dryer and to precise design of system. PMID:24425968

  19. Fluidized-Bed Waste-Heat Recovery System development. Semiannual report, 1 August 1981-31 January 1982

    Energy Technology Data Exchange (ETDEWEB)

    Cole, W. E.; DeSaro, R.; Joshi, C.

    1982-02-01

    The Fluidized-Bed Waste-Heat Recovery (FBWHR) System is designed to preheat this combustion air using the heat available in dirty flue gas streams. In this system, a recirculating medium is heated by the flue gas in a fluidized bed. The hot medium is then removed from the bed and placed in a second fluidized bed where it is fluidized by the combustion air. Through this process, the combustion air is heated. The cooled medium is then returned to the first bed. Initial development of this concept is for the aluminum smelting industry.

  20. RADIAL PROFILE OF THE SOLID FRACTION IN A LIQUID-SOLID CIRCULATING FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Tiefeng Wang; Jinfu Wang; Jing Lin; Yong Jin

    2003-01-01

    @@ Liquid-solid circulating fluidized beds have a number of attractive features suitable for processes where liquid-solid contact is important (Liang et al., 1996; Zhang et al., 2002).Liang et al. (1996) and Zheng et al. (2002) studied the radial profile of the solid fraction in the liquid-solid circulating fluidization regime and found that it is not uniform, unlike the conventional liquid-solid fluidized bed. This non-uniformity can affect reactant concentration distribution, mass transfer and ultimately reactant conversion.Therefore, information on the radial flow structure is crucial to reactor design and process optimization.

  1. Decorated carbon nanotubes by silicon deposition in fluidized bed for Li-ion battery anodes

    OpenAIRE

    Coppey, Nicolas; Noé, Laure; Monthioux, Marc; Caussat, Brigitte

    2013-01-01

    Multi-walled carbon nanotubes Graphistrength® were decorated with silicon by Fluidized Bed Chemical Vapor Deposition. The ability to fluidize of these nanotubes forming ball-shaped jumbles of several hundreds of microns in diameter and that of the final CNT-Si balls was first studied. These balls reveal to fluidize with characteristics of Geldart’s group A particles, i.e. without bubbles and with high bed expansion. Coating experiments from silane SiH4 were performed at 500°C in the 30 60 wt....

  2. Comparison of Fixed and Fluidized Beds Adsorber with Economic, Engineering, and Environmental approach

    Directory of Open Access Journals (Sweden)

    SEDIGHEH ATRKAR-ROSHAN

    2015-10-01

    Full Text Available Release  Volatile  organic  compounds  (VOCs  as  environmental  and  occupational  pollutant  cause  macro perspective affect such as climate change, humans and economic consequences. Although fixed bed absorber is widely used as a controlling method because of its economically and availability, but these absorbers are facing some issue like high pressure drop, non-uniform distribution of fluid, channeling and blocking. Fixed and fluidized beds adsorbent was compared from three economic, environmental and engineering perspectives using Multi Criteria Decision Making analysis (MCDA technique. An annular fluidized bed adsorber was designed and charged with 50-100 µm (100-140 ASTM mesh activated carbon (AC particles. Effects of factors like flow rate, particle size, inlet concentration and adsorption capacity of VOCs was investigated under steady state. In the flow rate less than 0.25(Lit.min-1, inlet gas slowly passes through the void spaces of the bed’s particles. By increasing the inlet flow from 0.3(Lit/min-1, bubbles start to form in the bed and the bed pressure drop decrease. The pressure drop of 6 (g of AC in minimum fluidization velocity was 20(KN.m-2. However, the pressure drop of 10 and 20(g of AC were 150 and 420(KN.m-2 respectively. “maximin” technique used for comparison of two beds indicated that minimum score of pack bed absorber are 0.37 while the minimum score of fluidized bed adsorber are 0.5. It indicated when the adsorbent particles are smaller, fluidized bed adsorber are more suitable to use. In addition, using MCDA technique indicated that annular fluidized bed adsorber could considered as an alternative of fixed beds adsorber.

  3. Comprehensive Mathematical Model for Coal Combustion in a Circulating Fluidized Bed Combustor

    Institute of Scientific and Technical Information of China (English)

    金晓钟; 吕俊复; 杨海瑞; 刘青; 岳光溪; 冯俊凯

    2001-01-01

    Char combustion is on a special reducing condition in the dense bed of a circulating fluidized bedcombustor. Experimental findings were used to develop a comprehensive mathematical model to simulate thehydrodynamic and combustion processes in a circulating fluidized bed combustor. In the model, gas-solidinteraction was used to account for the mass transfer between the bubble phase and the emulsion phase in thedense bed, which contributes to the reducing atmosphere in the dense bed. A core-annular structure wasassumed in the dilute area rather than a one-dimensional model. The submodels were combined to build thecomprehensive model to analyze the combustion in a circulating fluidized bed combustor and the effect ofoperating parameters on the coal combustion. The model predictions agree well with experimental results.

  4. Modern fluidized bed combustion in Ostrava-Karvina cogeneration plants

    Energy Technology Data Exchange (ETDEWEB)

    Mazac, V. [Energoprojekt Praha, Ostrava (Czechoslovakia); Novacek, A. [Moravskoslezske teplamy, Ostrava (Czechoslovakia); Volny, J. [Templamy Karvina (Czechoslovakia)

    1995-12-01

    The contemporary situation of our environment claims the sensitive approach to solving effective conversion of energy. Limited supplies of noble fuels and their prices evoke the need to use new combustion technologies of accessible fuels in given region without negative ecological influences. Energoproject participates in the preparation of the two projects in Ostrava-Karvin{acute a} black coal field in Czech Republic. The most effective usage of fuel energy is the combined of electricity and heat. If this physical principle is supported by a pressurized fluidized bed combustion (PFBC) one obtains a high electricity/heat ratio integrated steam-gas cycle on the basis of solid fuel. Cogeneration plant Toebovice is the dominant source (600 MW{sub th}) of Ostrava district heating system (1100 MW{sub th}). The high utilization of the installed output and utilization of the clean, compact and efficient of the PFBC technology is the principal but not the single reason for the selection of the Toebovice power plant as the first cogeneration plant for installation of the PFBC in Czech Republic. The boiler will burn black coal from the neighboring coal basin.

  5. Sorption-enhanced steam methane reforming in fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Johnsen, Kim

    2006-10-15

    Hydrogen is considered to be an important potential energy carrier; however, its advantages are unlikely to be realized unless efficient means can be found to produce it without generation of CO{sub 2}. Sorption-enhanced steam methane reforming (SE-SMR) represent a novel, energy-efficient hydrogen production route with in situ CO{sub 2} capture, shifting the reforming and water gas shift reactions beyond their conventional thermodynamic limits. The use of fluidized bed reactors for SE-SMR has been investigated. Arctic dolomite, a calcium-based natural sorbent, was chosen as the primary CO{sub 2}-acceptor in this study due to high absorption capacity, relatively high reaction rate and low cost. An experimental investigation was conducted in a bubbling fluidized bed reactor of diameter 0.1 m, which was operated cyclically and batch wise, alternating between reforming/carbonation conditions and higher-temperature calcination conditions. Hydrogen concentrations of >98 mole% on a dry basis were reached at 600 C and 1 atm, for superficial gas velocities in the range of {approx}0.03-0.1 m/s. Multiple reforming-regeneration cycles showed that the hydrogen concentration remained at {approx}98 mole% after four cycles. The total production time was reduced with an increasing number of cycles due to loss of CO{sub 2}-uptake capacity of the dolomite, but the reaction rates of steam reforming and carbonation seemed to be unaffected for the conditions investigated. A modified shrinking core model was applied for deriving carbonation kinetics of Arctic dolomite, using experimental data from a novel thermo gravimetric reactor. An apparent activation energy of 32.6 kj/mole was found from parameter fitting, which is in good agreement with previous reported results. The derived rate expression was able to predict experimental conversion up to {approx}30% very well, whereas the prediction of higher conversion levels was poorer. However, the residence time of sorbent in a continuous

  6. Operation of a fluidized-bed bioreactor for denitrification

    Energy Technology Data Exchange (ETDEWEB)

    Hancher, C W; Taylor, P A; Napier, J M

    1978-01-01

    Two denitrification fluidized-bed bioreactors of the same length (i.e., 5 m) but with different inside diameters (i.e., 5 and 10 cm) have been operated on feed ranging in nitrate concentration from 200 to 2000 g/m/sup 3/; thus far, good agreement has been obtained. Two 10-cm-ID bioreactors operating in series have also been tested; the results are in accordance with predicted results based on the performance of a 5-cm-ID bioreactor. The overall denitrification rate in the dual 10-cm-ID bioreactor system was found to be 23 kg N(NO/sub 3//sup -/)/day-m/sup 3/ using feed with a nitrate concentration of 1800 g/m/sup 3/. Data obtained in operating-temperature tests indicate that the maximum denitrification rate is achieved between 22 and 30/sup 0/C. These data will form the basis of the design of our mobile pilot plant which consists of dual 20-cm-ID by 7.3-m-long bioreactors.

  7. FLUIDIZED BED STEAM REFORMING ENABLING ORGANIC HIGH LEVEL WASTE DISPOSAL

    International Nuclear Information System (INIS)

    Waste streams planned for generation by the Global Nuclear Energy Partnership (GNEP) and existing radioactive High Level Waste (HLW) streams containing organic compounds such as the Tank 48H waste stream at Savannah River Site have completed simulant and radioactive testing, respectfully, by Savannah River National Laboratory (SRNL). GNEP waste streams will include up to 53 wt% organic compounds and nitrates up to 56 wt%. Decomposition of high nitrate streams requires reducing conditions, e.g. provided by organic additives such as sugar or coal, to reduce NOX in the off-gas to N2 to meet Clean Air Act (CAA) standards during processing. Thus, organics will be present during the waste form stabilization process regardless of the GNEP processes utilized and exists in some of the high level radioactive waste tanks at Savannah River Site and Hanford Tank Farms, e.g. organics in the feed or organics used for nitrate destruction. Waste streams containing high organic concentrations cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by pretreatment. The alternative waste stabilization pretreatment process of Fluidized Bed Steam Reforming (FBSR) operates at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). The FBSR process has been demonstrated on GNEP simulated waste and radioactive waste containing high organics from Tank 48H to convert organics to CAA compliant gases, create no secondary liquid waste streams and create a stable mineral waste form

  8. Inductive classification of operating data from a fluidized bed calciner

    International Nuclear Information System (INIS)

    A process flowsheet expert system for a fluidized bed calciner which solidifies high-level radioactive liquid waste was developed from pilot-plant data using a commercial, inductive classification program. After initial classification of the data, the resulting rules were inspected and adjusted to match existing knowledge of process chemistry. The final expert system predicts performance of process flowsheets based upon the chemical composition of the calciner feed and has been successfully used to identify potential operational problems prior to calciner pilot-plant testing of new flowsheets and to provide starting parameters for pilot-plant tests. By using inductive classification techniques to develop the initial rules from the calciner pilot-plant data and using existing process knowledge to verify the accuracy of these rules, an effective expert system was developed with a minimum amount of effort. This method may be applied for developing expert systems for other processes where numerous operating data are available and only general process chemistry effects are known

  9. FLUIDIZED BED STEAM REFORMING ENABLING ORGANIC HIGH LEVEL WASTE DISPOSAL

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M

    2008-05-09

    Waste streams planned for generation by the Global Nuclear Energy Partnership (GNEP) and existing radioactive High Level Waste (HLW) streams containing organic compounds such as the Tank 48H waste stream at Savannah River Site have completed simulant and radioactive testing, respectfully, by Savannah River National Laboratory (SRNL). GNEP waste streams will include up to 53 wt% organic compounds and nitrates up to 56 wt%. Decomposition of high nitrate streams requires reducing conditions, e.g. provided by organic additives such as sugar or coal, to reduce NOX in the off-gas to N2 to meet Clean Air Act (CAA) standards during processing. Thus, organics will be present during the waste form stabilization process regardless of the GNEP processes utilized and exists in some of the high level radioactive waste tanks at Savannah River Site and Hanford Tank Farms, e.g. organics in the feed or organics used for nitrate destruction. Waste streams containing high organic concentrations cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by pretreatment. The alternative waste stabilization pretreatment process of Fluidized Bed Steam Reforming (FBSR) operates at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). The FBSR process has been demonstrated on GNEP simulated waste and radioactive waste containing high organics from Tank 48H to convert organics to CAA compliant gases, create no secondary liquid waste streams and create a stable mineral waste form.

  10. Characterization of fuels for atmospheric fluidized bed combustion

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C.S. (Oak Ridge National Lab., TN (USA)); Rowley, D.R.; Perna, M.A. (Babcock and Wilcox Co., Alliance, OH (USA). Research Center); Stallings, J.W. (Electric Power Research Inst., Palo Alto, CA (USA)); Divilio, R.J. (Combustion Systems, Inc., Silver Spring, MD (USA))

    1990-01-01

    The Electric Power Research Institute (EPRI) has sponsored a fuels characterization program for the past several years with the intention of assisting utilities and boiler manufacturers in evaluating fuel quality impact on atmospheric fluidized bed combustion (AFBC) performance. The goal has been to provide an improved framework for making fuel switching decisions and consolidating operating experience. Results from this program include a set of bench-scale testing procedures, a fuel characterization data base, and a performance simulation model that links fuel characteristics to combustion performance. This paper reviews the major results of the fuels characterization program. The testing procedures, data base, and performance simulation models are briefly described and their application illustrated with examples. Performance predictions for the B W 1-ft{sup 2} bench-scale AFBC and the Tennessee Valley Authority (TVA) 20 MW(e) AFBC Pilot Plant are compared with actual test data. The relationship of coal rank to combustion is discussed. 11 refs., 12 figs., 5 tabs.

  11. Effectiveness of fluidized pellet bed for removing soluble contaminants

    Institute of Scientific and Technical Information of China (English)

    WANG Xiaochang; LI Zhihua; WANG Zhen; LI Jinrong; LI Jiayu; CHEN Rong

    2009-01-01

    Fluidized pellet bed (FPB) has been successfully applied in water and wastewater treatment. However, the removal mechanism of contaminants especially the soluble ones, is still unclear. This study aimed to evaluate the effectiveness of FPB reactor for removing soluble contaminants from synthetic wastewater. By only coagulation through jar test operation with addition of polyaluminium chloride (PACl) as primary coagulant and polyacryamide (PAM) as coagulant-aid, the removals of soluble chemical oxygen demand (COD), suspended solids (SS), total phosphorus (TP), and NH4+-N were found to be only 2.2%--7.5%, 5.7%--25.5%, and 9.9%--18.5%, respectively. However, by FPB operation under the same dosage of coagulants, these values increased to 82.7%, 37.2%, and 50%, indicating that the formation of pellets in the FPB effectively enhanced the removal of soluble contaminants. By careful comparison of the settleablility and filterability of the pollutants after coagulation, the originally soluble contaminants could be divided into three groups, namely: (i) coagulated-and-settleable, (ii) coagulated-but-nonsettleable, and (iii) uncoagulable. It was found that not only the first two groups but also a large part of the third group could be effectively removed by FPB operation. However, the mechanism for the removal of the uncoagulable pollutants by FPB operation still needs further investigation.

  12. Treating exhaust gas from a pressurized fluidized bed reaction system

    Science.gov (United States)

    Isaksson, Juhani; Koskinen, Jari

    1995-01-01

    Hot gases from a pressurized fluidized bed reactor system are purified. Under superatmospheric pressure conditions hot exhaust gases are passed through a particle separator, forming a flitrate cake on the surface of the separator, and a reducing agent--such as an NO.sub.x reducing agent (like ammonia), is introduced into the exhaust gases just prior to or just after particle separation. The retention time of the introduced reducing agent is enhanced by providing a low gas velocity (e.g. about 1-20 cm/s) during passage of the gas through the filtrate cake while at superatmospheric pressure. Separation takes place within a distinct pressure vessel the interior of which is at a pressure of about 2-100 bar, and-introduction of reducing agent can take place at multiple locations (one associated with each filter element in the pressure vessel), or at one or more locations just prior to passage of clean gas out of the pressure vessel (typically passed to a turbine).

  13. Research into Biomass and Waste Gasification in Atmospheric Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Skala, Zdenek; Ochrana, Ladislav; Lisy, Martin; Balas, Marek; Kohout, Premysl; Skoblja, Sergej

    2007-07-01

    Considerable attention is paid in the Czech Republic to renewable energy sources. The largest potential, out of them all, have biomass and waste. The aim therefore is to use them in CHP in smaller units (up to 5MWel). These are the subject of the research summarized in our article. The paper presents results of experimental research into gasification in a 100 kW AFB gasifier situated in Energy Institute, Faculty of Mechanical Engineering, Brno University of Technology, and fitted with gas cleaning equipment. Within the research, study was carried out into gas cleaning taking primary measures in the fluidized bed and using hot filter, metal-based catalytic filter, and wet scrubber. Descriptions and diagrams are given of the gasifier and new ways of cleaning. Results include: Impact of various fuels (farming and forest wastes and fast-growing woods and culm plants) on fuel gas quality. Individual kinds of biomass have very different thermal and physical properties; Efficiency of a variety of cleaning methods on content of dust and tars and comparison of these methods; and, Impact of gasifier process parameters on resultant gas quality. (auth)

  14. Operation of a fluidized-bed bioreactor for denitrification

    International Nuclear Information System (INIS)

    Two denitrification fluidized-bed bioreactors of the same length (i.e., 5 m) but with different inside diameters (i.e., 5 and 10 cm) have been operated on feed ranging in nitrate concentration from 200 to 2000 g/m3; thus far, good agreement has been obtained. Two 10-cm-ID bioreactors operating in series have also been tested; the results are in accordance with predicted results based on the performance of a 5-cm-ID bioreactor. The overall denitrification rate in the dual 10-cm-ID bioreactor system was found to be 23 kg N(NO3-)/day-m3 using feed with a nitrate concentration of 1800 g/m3. Data obtained in operating-temperature tests indicate that the maximum denitrification rate is achieved between 22 and 300C. These data will form the basis of the design of our mobile pilot plant which consists of dual 20-cm-ID by 7.3-m-long bioreactors

  15. Elemental mercury vapor capture by powdered activated carbon in a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizio Scala; Riccardo Chirone; Amedeo Lancia [Istituto di Ricerche sulla Combustione - CNR, Napoli (Italy)

    2011-06-15

    A bubbling fluidized bed of inert material was used to increase the activated carbon residence time in the reaction zone and to improve its performance for mercury vapor capture. Elemental mercury capture experiments were conducted at 100{sup o}C in a purposely designed 65 mm ID lab-scale pyrex reactor, that could be operated both in the fluidized bed and in the entrained bed configurations. Commercial powdered activated carbon was pneumatically injected in the reactor and mercury concentration at the outlet was monitored continuously. Experiments were carried out at different inert particle sizes, bed masses, fluidization velocities and carbon feed rates. Experimental results showed that the presence of a bubbling fluidized bed led to an increase of the mercury capture efficiency and, in turn, of the activated carbon utilization. This was explained by the enhanced activated carbon loading and gas-solid contact time that establishes in the reaction zone, because of the large surface area available for activated carbon adhesion/deposition in the fluidized bed. Transient mercury concentration profiles at the bed outlet during the runs were used to discriminate between the controlling phenomena in the process. Experimental data have been analyzed in the light of a phenomenological framework that takes into account the presence of both free and adhered carbon in the reactor as well as mercury saturation of the adsorbent. 14 refs., 7 figs.

  16. Fluidized bed coupled rotary reactor for nanoparticles coating via atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Duan, Chen-Long; Liu, Xiao; Chen, Rong, E-mail: rongchen@mail.hust.edu.cn, E-mail: bshan@mail.hust.edu.cn [State Key Laboratory of Digital Manufacturing Equipment and Technology, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074 (China); Shan, Bin, E-mail: rongchen@mail.hust.edu.cn, E-mail: bshan@mail.hust.edu.cn [State Key Laboratory of Material Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, 1037 Luoyu Road, Wuhan, Hubei 430074 (China)

    2015-07-15

    A fluidized bed coupled rotary reactor has been designed for coating on nanoparticles (NPs) via atomic layer deposition. It consists of five major parts: reaction chamber, dosing and fluidizing section, pumping section, rotary manipulator components, as well as a double-layer cartridge for the storage of particles. In the deposition procedure, continuous fluidization of particles enlarges and homogenizes the void fraction in the particle bed, while rotation enhances the gas-solid interactions to stabilize fluidization. The particle cartridge presented here enables both the fluidization and rotation acting on the particle bed, demonstrated by the analysis of pressure drop. Moreover, enlarged interstitials and intense gas–solid contact under sufficient fluidizing velocity and proper rotation speed facilitate the precursor delivery throughout the particle bed and consequently provide a fast coating process. The cartridge can ensure precursors flowing through the particle bed exclusively to achieve high utilization without static exposure operation. By optimizing superficial gas velocities and rotation speeds, minimum pulse time for complete coating has been shortened in experiment, and in situ mass spectrometry showed the precursor usage can reach 90%. Inductively coupled plasma-optical emission spectroscopy results suggested a saturated growth of nanoscale Al{sub 2}O{sub 3} films on spherical SiO{sub 2} NPs. Finally, the uniformity and composition of the shells were characterized by high angle annular dark field-transmission electron microscopy and energy dispersive X-ray spectroscopy.

  17. Study of a three-stage fluidized bed process treating acrylic synthetic-fiber manufacturing wastewater containing high-strength nitrogenous compounds.

    Science.gov (United States)

    Cheng, S S; Chen, Y N; Wu, K L; Chuang, H P; Chen, S D

    2004-01-01

    Polyacrylonitrile (PAN) is one of the major synthetic fibers commonly used in the mass production of clothing. The chemical synthesis of PAN is carried out by polymerization of the acrylonitrile (AN) monomers with co-monomers such as vinyl acetate, methyl acrylate and cyclohexyl acrylate. Using water quality analysis of the PAN wastewater, high concentration of organic nitrogen was found and the TKN/COD ratios achieved were 0.15-0.26, indicating the complicated biodegradation characteristics for the PAN wastewater. In order to enhance biodegradation of nitrogenous compounds in PAN wastewater, a combined three-stage process of thermophilic anaerobic/anoxic denitrification/aerobic nitrification fluidized bed reactors was employed. The results indicated that the concentration of effluent in the three-stage process of OD and organic nitrogen was 175 mg/L and 13 mg/L, respectively. Furthermore, molecular biotechnology was applied to study the microbial population in the thermophilic anaerobic fluidized bed reactor. From the results of denaturing gradient gel electrophoresis, the diversity of PAN-degrading bacteria would change in different volumetric loading. Furthermore, the bacteria communities in the thermophilic anaerobic fluidized bed reactor were also studied by fluorescence in situ hybridization and confocal laser scanning microscopy. Alpha and delta-Proteobacteria were dominant in the bacteria population, and some high G+C content bacteria and Clostridium could be characterized in this system. PMID:15137414

  18. Tratamento anaeróbio de pentaclorofenol em reator de leito fluidificado alimentado com água residuária sintética contendo glicose como fonte única de carbono Anaerobic treatment of pentachlorophenol in a fluidized bed reactor fed with synthetic wastewater containing glucose as a single carbon source

    Directory of Open Access Journals (Sweden)

    Flavio Bentes Freire

    2008-09-01

    Full Text Available Neste trabalho foi utilizado um reator anaeróbio de leito fluidificado (RALF, tratando água residuária sintética contendo pentaclorofenol (PCP, submetido a condições operacionais menos idealizadas. Utilizou-se um reator com volume de 16 litros, com partículas de carvão ativado granular como meio suporte. O desempenho do reator foi verificado pelas análises usuais de monitoramento (pH, alcalinidade, DQO, ácidos voláteis e também por análises de microscopia e concentração de PCP. A presença de PCP no sistema, nas concentrações utilizadas, não alterou de maneira significativa a qualidade da biomassa presente, e nem os parâmetros de monitoramento. Em concentrações afluentes de PCP variando de 1 a 6 mg/L, foram observadas eficiências médias de remoção de 92% e 70%, respectivamente.In the present work, an anaerobic fluidized bed reactor (AFBR was used for the treatment of a synthetic wastewater containing pentachlorophenol (PCP subjected to less idealized operating conditions. The reactor was a 16 litres tank with granular activated carbon particles as support media. Evaluation of AFBR performance was done by the analysis of usual monitoring parameters (pH, alkalinity, COD, volatile acids together with microscopy and PCP concentration analysis. The presence of PCP under the concentrations used did not significantly alter the amount of biomass and the performance monitoring parameters. Removal average efficiencies of the order of 92% and 70% were obtained for PCP inflow concentrations in the range of 1 to 6mg/l.

  19. Investigation of Gas Solid Fluidized Bed Dynamics with Non-Spherical Particles

    Energy Technology Data Exchange (ETDEWEB)

    Choudhuri, Ahsan

    2013-06-30

    One of the largest challenges for 21st century is to fulfill global energy demand while also reducing detrimental impacts of energy generation and use on the environment. Gasification is a promising technology to meet the requirement of reduced emissions without compromising performance. Coal gasification is not an incinerating process; rather than burning coal completely a partial combustion takes place in the presence of steam and limited amounts of oxygen. In this controlled environment, a chemical reaction takes place to produce a mixture of clean synthetic gas. Gas-solid fluidized bed is one such type of gasification technology. During gasification, the mixing behavior of solid (coal) and gas and their flow patterns can be very complicated to understand. Many attempts have taken place in laboratory scale to understand bed hydrodynamics with spherical particles though in actual applications with coal, the particles are non-spherical. This issue drove the documented attempt presented here to investigate fluidized bed behavior using different ranges of non-spherical particles, as well as spherical. For this investigation, various parameters are controlled that included particle size, bed height, bed diameter and particle shape. Particles ranged from 355 µm to 1180 µm, bed diameter varied from 2 cm to 7 cm, two fluidized beds with diameters of 3.4 cm and 12.4 cm, for the spherical and non-spherical shaped particles that were taken into consideration. Pressure drop was measured with increasing superficial gas velocity. The velocity required in order to start to fluidize the particle is called the minimum fluidization velocity, which is one of the most important parameters to design and optimize within a gas-solid fluidized bed. This minimum fluidization velocity was monitored during investigation while observing variables factors and their effect on this velocity. From our investigation, it has been found that minimum fluidization velocity is independent of bed

  20. Non-intrusive measurement and hydrodynamics characterization of gas-solid fluidized beds: a review

    Science.gov (United States)

    Sun, Jingyuan; Yan, Yong

    2016-11-01

    Gas-solid fluidization is a well-established technique to suspend or transport particles and has been applied in a variety of industrial processes. Nevertheless, our knowledge of fluidization hydrodynamics is still limited for the design, scale-up and operation optimization of fluidized bed reactors. It is, therefore, essential to characterize the two-phase flow behaviours in gas-solid fluidized beds and monitor the fluidization processes for control and optimization. A range of non-intrusive techniques have been developed or proposed for measuring the fluidization dynamic parameters and monitoring the flow status without disturbing or distorting the flow fields. This paper presents a comprehensive review of the non-intrusive measurement techniques and the current state of knowledge and experience in the characterization and monitoring of gas-solid fluidized beds. These techniques are classified into six main categories as per sensing principles, electrostatic, acoustic emission and vibration, visualization, particle tracking, laser Doppler anemometry and phase Doppler anemometry as well as pressure-fluctuation methods. Trends and future developments in this field are also discussed.

  1. Removal of pharmaceuticals and organic matter from municipal wastewater using two-stage anaerobic fluidized membrane bioreactor.

    Science.gov (United States)

    Dutta, Kasturi; Lee, Ming-Yi; Lai, Webber Wei-Po; Lee, Chien Hsien; Lin, Angela Yu-Chen; Lin, Cheng-Fang; Lin, Jih-Gaw

    2014-08-01

    The aim of present study was to treat municipal wastewater in two-stage anaerobic fluidized membrane bioreactor (AFMBR) (anaerobic fluidized bed reactor (AFBR) followed by AFMBR) using granular activated carbon (GAC) as carrier medium in both stages. Approximately 95% COD removal efficiency could be obtained when the two-stage AFMBR was operated at total HRT of 5h (2h for AFBR and 3h for AFMBR) and influent COD concentration of 250mg/L. About 67% COD and 99% TSS removal efficiency could be achieved by the system treating the effluent from primary clarifier of municipal wastewater treatment plant, at HRT of 1.28h and OLR of 5.65kg COD/m(3)d. The system could also effectively remove twenty detected pharmaceuticals in raw wastewaters with removal efficiency in the range of 86-100% except for diclofenac (78%). No other membrane fouling control was required except scouring effect of GAC for flux of 16LMH. PMID:24745898

  2. Computer simulation of the hydrodynamics of a two-dimensional gas-fluidized bed

    NARCIS (Netherlands)

    Kuipers, J.A.M.; Duin, van K.J.; Beckum, van F.P.H.; Swaaij, van W.P.M.

    1993-01-01

    A first principles model of a gas-fluidized bed has been applied to calculate the hydrodynamics of a two-dimensional (2-D) bed with an orifice in the middle of a porous plate distributor. The advanced hydrodynamic model is based on a two fluid model approach in which both phases are considered to be

  3. A study on Heat Transfer for Immersed Tube in Internally Circulating Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    TianWendong; HaoJinhua; 等

    1999-01-01

    Heat transfer coefficients for horizontally immersed tubes have been studied in a model of ICFB(Inter-nally Circulating Fluidized Bed).The characteristics in ICFB were found to be significantly different from those in bubbing bed.There is a flowing zone with high velocity in the heat exchange zone.The heat transfer coefficients strongly depend on the fluidized velocity in the flowing zone.The heat exchange process and suitable bed temperature can be controlled according to this feature.Based on the results of the experiments,a formulation for heat transfer has been developed.

  4. Clustering behavior of solid particles in two-dimensional liquid-solid fluidized-beds

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this paper, the clustering behavior of solid particles in a two-dimensional (2D) liquid-solid fluidized-bed was studied by using the charge coupled devices (CCD) imaging measuring and processing technique and was characterized by fractal analysis. CCD images show that the distribution of solid particles in the 2D liquid-solid fluidised-bed is not uniform and self-organization behavior of solid particles was observed under the present experimental conditions. The solid particles move up in the 2D fluidized-bed in groups or clusters whose configurations are often in the form of horizontal strands. The box fractal dimension of the cluster images in the 2D liquid-solid fluidized-bed increases with the rising of solid holdup and reduces with the increment of solid particle diameter and superficial liquid velocity. At given solid holdup and solid particle size,the lighter particles show smaller fractal dimensions.

  5. Stable hydrogen production by methane steam reforming in a two zone fluidized bed reactor: Experimental assessment

    Science.gov (United States)

    Pérez-Moreno, L.; Soler, J.; Herguido, J.; Menéndez, M.

    2013-12-01

    The Two Zone Fluidized Bed Reactor concept is proposed for hydrogen production via the steam reforming of methane (SRM) including integrated catalyst regeneration. In order to study the effect of the contact mode, the oxidative SRM has been carried out over a Ni/Al2O3 catalyst using a fixed bed reactor (fBR), a conventional fluidized-bed reactor (FBR) and the proposed two-zone fluidized bed reactor (TZFBR). The technical feasibility of these reactors has been studied experimentally, investigating their performance (CH4 conversion, CO and H2 selectivity, and H2 global yield) and stability under different operating conditions. Coke generation in the process has been verified by several techniques. A stable performance was obtained in the TZFBR, where coke formation was counteracted with continuous catalyst regeneration. The viability of the TZFBR for carrying out this process with a valuable global yield to hydrogen is demonstrated.

  6. Combustion of gases released from peat or biomass in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Raiko, R. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

    1996-12-01

    Temperature and gas concentration experiments have been conducted to determine at what temperature carbon monoxide, methane and propane begin to react within the particulate phase of a bubbling fluidized bed. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 50 mm surrounded by an electric heater. Two different natural quartz sands were used (d{sub p} =0.35 mm and 0.6 mm). The bed height used varied between 100 and 260 mm (in unfluidized state). A porous plate distributor, made of kaowool, was used to avoid jets appearing at the distributor. The bed was operated at incipient fluidization (u = 5.9-9 cm/s). The bed temperatures used ranged from 600 deg C to 850 deg C. It was found that carbon monoxide, methane and propane react inside a fluidized bed, but often other conditions than temperature have a considerable effect on the rate of the reaction. The critical temperature was found to be 650 deg C for propane and carbon monoxide and 700 deg C for methane. With under-stoichiometric mixture of carbon monoxide and air the heat release can be over 2.5 MW/m{sup 3} when bed temperature is 650 deg C. According to these experiments it is obvious that the reaction mechanism for carbon monoxide oxidation inside a fluidized bed differs greatly from that of gas phase only. The results of our more than 1300 test runs show clearly the varying effects of the different bed materials. Even with the same bed material totally different results can be obtained. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies was conducted with both fresh bed particles and used bed particles. Also the effect of commonly used ingredients, like limestone and dolomite, was tested. A global model for carbon monoxide oxidation inside a fluidized bed was introduced. The model was tested against measured data from the laboratory-scale fluidized bed test rig. (Abstract Truncated)

  7. Effect of static bed height in the upper fluidized bed on flow behavior in the lower riser section of a coupled reactor

    Institute of Scientific and Technical Information of China (English)

    Dewu Wang; Chunxi Lu; Chaoyu Yan

    2009-01-01

    To study olefin reduction by using an auxiliary reactor for FCC naphtha upgrading, a large-scale cold model of a riser-bed coupled to an upper fluidized bed was established. The effect of static bed height in the upper fluidized bed on particle flow behavior in the lower riser was investigated experimentally. A restriction index of solids holdup was used to evaluate quantitatively the restrictive effect of the upper fluidized bed. Experimental results show that, under the restrictive effect of the upper fluidized bed, the riser could be divided into three regions in the longitudinal direction: accelerating, fully developed and restriction. The axial distribution of solids holdup in the riser is characterized by large solids holdup in the top and bottom sections and small solids holdup in the middle section. Overall solids holdup increased with increasing static bed height in the upper fluidized bed, while particle velocity decreased. Such restrictive effect of the upper fluidized bed could extend from the middle and top sections to the whole riser volume when riser outlet resistance is increased, which increases with increasing static bed height in the upper fluidized bed. The upper bed exerts the strongest restriction on the area close to the riser outlet.

  8. DURABILITY TESTING OF FLUIDIZED BED STEAM REFORMER (FBSR) WASTE FORMS

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-01-06

    Fluidized Bed Steam Reforming (FBSR) is being considered as a potential technology for the immobilization of a wide variety of high sodium aqueous radioactive wastes. The addition of clay and a catalyst as co-reactants converts high sodium aqueous low activity wastes (LAW) such as those existing at the Hanford and Idaho DOE sites to a granular ''mineralized'' waste form that may be made into a monolith form if necessary. Simulant Hanford and Idaho high sodium wastes were processed in a pilot scale FBSR at Science Applications International Corporation (SAIC) Science and Technology Applications Research (STAR) facility in Idaho Falls, ID. Granular mineral waste forms were made from (1) a basic Hanford Envelope A low-activity waste (LAW) simulant and (2) an acidic INL simulant commonly referred to as sodium-bearing waste (SBW). The FBSR waste forms were characterized and the durability tested via ASTM C1285 (Product Consistency Test), the Environmental Protection Agency (EPA) Toxic Characteristic Leaching Procedure (TCLP), and the Single Pass Flow Through (SPFT) test. The durability of the FBSR waste form products was tested in order to compare the measured durability to previous FBSR waste form testing on Hanford Envelope C waste forms that were made by THOR Treatment Technologies (TTT) and to compare the FBSR durability to vitreous LAW waste forms, specifically the Hanford low activity waste (LAW) glass known as the Low-activity Reference Material (LRM). The durability of the FBSR waste form is comparable to that of the LRM glass for the test responses studied.

  9. Graphitization kinetics of fluidized-bed pyrolytic carbons

    International Nuclear Information System (INIS)

    Graphitization of 12 fluidized-bed pyrocarbons was studied as a function of heat-treatment time and temperature (1350 to 30000C) to investigate the effect of initial microstructure on the graphitization process. The term ''graphitization'' is defined to include any thermally induced structural change, whether or not any layer stacking order is attained. A broad range of CVD microstructures was prepared at temperatures from 1150 to 19000C and various propylene and methane concentrations. The twelve carbons spanned a wide range of graphitizabilities, primarily as a function of deposition temperature. Hydrocarbon concentration was of much less importance except for deposition at 19000C. Hydrogen content of the as-deposited carbons decreased with increasing temperature of deposition, and initial graphitization behavior of the low-temperature carbons appeared to be related to hydrogen content and evolution. Rates of change in the parameters varied widely throughout the range of heat-treatment times (HTt) and temperatures (HTT) for the different carbons showing differences between the more graphitizable or ''soft'' carbons from the nongraphitizing or ''hard'' carbons. ΔH for nongraphitizing carbons was 175 +- 15 kcal below 19500C, 240 +- 35 kcal at 1950 to 27000C, and 330 +- 20 kcal above 27000C. For graphitizing carbons deposited at 11500C, values near 245 kcal were obtained from anti chi data for the HTT range 1350 to 16500C, while densification data yielded values of about 160 kcal in the same range. The behaviors observed for graphitizable carbons above 20000C are consistent with literature. Different kinetic behaviors below 20000C were shown to be due to different initial microstructures as well as to different parameters measured. (U.S.)

  10. Pressurized fluidized-bed hydroretorting of Eastern oil shales

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, M.J.; Mensinger, M.C.; Rue, D.M.; Lau, F.S. (Institute of Gas Technology, Chicago, IL (United States)); Schultz, C.W. (Alabama Univ., University, AL (United States)); Parekh, B.K. (Kentucky Univ., Lexington, KY (United States)); Misra, M. (Nevada Univ., Reno, NV (United States)); Bonner, W.P. (Tennessee Technological Univ., Cookeville, TN (United States))

    1992-11-01

    The Devonian oil shales of the Eastern United States are a significant domestic energy resource. The overall objective of the multi-year program, initiated in October 1987 by the US Department of Energy is to perform the research necessary to develop the Pressurized Fluidized-Bed Hydroretorting (PFH) process for producing oil from Eastern oil shales. The program also incorporates research on technologies in areas such as raw shale preparation, beneficiation, product separation, and waste disposal that have the potential of improving the economics and/or environmental acceptability of recovering oil from oil shales using the PFH process. The results of the original 3-year program, which was concluded in May 1991, have been summarized in a four-volume final report published by IGT. DOE subsequently approved a 1-year extension to the program to further develop the PFH process specifically for application to beneficiated shale as feedstock. Studies have shown that beneficiated shale is the preferred feedstock for pressurized hydroretorting. The program extension is divided into the following active tasks. Task 3. testing of process improvement concepts; Task 4. beneficiation research; Task 5. operation of PFH on beneficiated shale; Task 6. environmental data and mitigation analyses; Task 7. sample procurement, preparation, and characterization; and Task 8. project management and reporting. In order to accomplish all the program objectives, the Institute of Gas Technology (IGT), the prime contractor, worked with four other institutions: the University of Alabama/Mineral Resources Institute (MRI), the University of Kentucky Center for Applied Energy Research (UK-CAER), the University of Nevada (UN) at Reno, and Tennessee Technological University (TTU). This report presents the work performed during the program extension from June 1, 1991 through May 31, 1992.

  11. Degradation of TCE using sequential anaerobic biofilm and aerobic immobilized bed reactor

    Science.gov (United States)

    Chapatwala, Kirit D.; Babu, G. R. V.; Baresi, Larry; Trunzo, Richard M.

    1995-01-01

    Bacteria capable of degrading trichloroethylene (TCE) were isolated from contaminated wastewaters and soil sites. The aerobic cultures were identified as Pseudomonas aeruginosa (four species) and Pseudomonas fluorescens. The optimal conditions for the growth of aerobic cultures were determined. The minimal inhibitory concentration values of TCE for Pseudomonas sps. were also determined. The aerobic cells were immobilized in calcium alginate in the form of beads. Degradation of TCE by the anaerobic and dichloroethylene (DCE) by aerobic cultures was studied using dual reactors - anaerobic biofilm and aerobic immobilized bed reactor. The minimal mineral salt (MMS) medium saturated with TCE was pumped at the rate of 1 ml per hour into the anaerobic reactor. The MMS medium saturated with DCE and supplemented with xylenes and toluene (3 ppm each) was pumped at the rate of 1 ml per hour into the fluidized air-uplift-type reactor containing the immobilized aerobic cells. The concentrations of TCE and DCE and the metabolites formed during their degradation by the anaerobic and aerobic cultures were monitored by GC. The preliminary study suggests that the anaerobic and aerobic cultures of our isolates can degrade TCE and DCE.

  12. An analysis of the chaotic motion of particles of different sizes in a gas fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The dynamic behavior of individual particles during the mixing/segregation process of particle mixtures in a gas fluidized bed is analyzed. The analysis is based on the results generated from discrete particle simulation, with the focus on the trajectory of and forces acting on individual particles.Typical particles are selected representing three kinds of particle motion:a flotsam particle which is initially at the bottom part of the bed and finally fluidized at the top part of the bed; a jetsam particle which is initially at the top part of the bed and finally stays in the bottom de-fluidized layer of the bed; and a jetsam particle which is intermittently joining the top fluidized and bottom de-fluidized layers. The results show that the motion of a particle is chaotic at macroscopic or global scale, but can be well explained at a microscopic scale in terms of its interaction forces and contact conditions with other particles, particle-fluid interaction force, and local flow structure. They also highlight the need for establishing a suitable method to link the information generated and modeled at different time and length scales.

  13. Biological nutrient removal from leachate using a pilot liquid-solid circulating fluidized bed bioreactor (LSCFB).

    Science.gov (United States)

    Eldyasti, Ahmed; Chowdhury, Nabin; Nakhla, George; Zhu, Jesse

    2010-09-15

    Biological treatment of landfill leachate is a concern due to toxicity, high ammonia, low biodegradable organic matter concentrations, and low carbon-to-nitrogen ratio. To study the reliability and commercial viability of leachate treatment using an integrated liquid-solid circulating fluidized bed bioreactor (LSCFB), a pilot-scale LSCFB was established at the Adelaide Pollution Control Plant, London, Ontario, Canada. Anoxic and aerobic columns were used to optimize carbon and nutrient removal capability from leachate using 600 microm lava rock with a total porosity of 61%, at empty bed contact times (EBCTs) of 0.55, 0.49, and 0.41 d. The LSCFB achieved COD, nitrogen, and phosphorus removal efficiencies of 85%, 80%, and 70%, respectively at a low carbon-to-nitrogen ratio of 3:1 and nutrients loading rates of 2.15 kg COD/(m(3) d), 0.70 kg N/(m(3) d), and 0.014 kg P/(m(3) d), as compared with 60-77% COD and 70-79% nitrogen removal efficiencies achieved by upflow anaerobic sludge blanket (UASB) and moving bed bioreactor (MBBR), respectively. The LSCFB effluent characterized by

  14. Eulerian-Lagrangian simulation of a bubbling fluidized bed reactor: Assessment of drag force correlations

    Directory of Open Access Journals (Sweden)

    Ku Xiao-Ke

    2012-01-01

    Full Text Available An Eulerian-Lagrangian approach is developed within the OpenFOAM framework to investigate the effects of three well-known inter-phase drag force correlations on the fluidization behavior in a bubbling fluidized bed reactor. The results show a strong dependency on the restitution coefficient and the friction coefficient and no occurrence of bubbling and slugging for the ideal-collision case. The mean pressure drops predicted by the three models agree quite well with each other.

  15. Hydrodynamics and Transient Heat Transfer Characteristics in Fluidized and Spouted Beds

    OpenAIRE

    Brown, Steven Lewis

    2012-01-01

    Hydrodynamics and heat transfer characteristics found in fluidization were studied in a small scale laboratory fluidized bed. Experiments were designed to capture field data on multiple slit jet gas distributor systems for the validation of computational models. Localized data was quantified through the use of several novel non-intrusive experimental measurement techniques. The analyses provide a unique study that connects full field-of-view multiphase flow dynamics with transient heat transf...

  16. Adaptation of the continuous cold trap system of fluidized-bed to the fluoride volatility process

    International Nuclear Information System (INIS)

    A continuous cold trap system consisting of fluidized condenser and stripper has been evaluated with a view to adapt it to the Fluoride Volatility Process in establishing the continuous purification process without radiation decomposition of PuF6. Its feasibility is shown by the test with UF6-air. Necessary conditions for the cold trap, and performance of the two inch-dia. fluidized bed cold trap system are presented, and also a model of mist formation in the condenser. (auth.)

  17. MULTIFRACTAL ANALYSIS OF PARTICLE-FLUID SYSTEM IN A CIRCULATING FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Liping; Ma; Weixing; Huang; Yanfu; Shi; Huarui; Yu; Jingxu; Zhu

    2005-01-01

    In this paper, multifractal analysis together with wavelet transform modulus maxima (WTMM) method is used to analyze the fluctuating signals of circulating fluidized bed (CFB). Singularity spectrum shows that the gas-particle flow in CFB has multifractal character. Motion behavior of the particle-fluid system of CFB can be described by singularity spectrum. Intermittency index can be used to determine the transition of flow regime from fast fluidization to pneumatic conveying.

  18. Effect of promoters on dynamics of gas-solid fluidized bed-Statistical and ANN approaches

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In this study, a bubbling fluidized bed column, 99 mm in inside diameter and 960 mm in height, was used to investigate the effect of rod and disc promoters on fluctuation and expansion ratios. Factorial design (statistical approach) and artificial neural network (ANN) models were developed to predict the fluctuation and expansion ratios in this gas-solid fluidized bed with varying gas flow rates, bed heights, particle sizes and densities. The fluctuation and expansion predicted using these statistical and ANN models, for beds with and without promoters, were found to agree well with corresponding experiments. The statistical model was found to be superior to the ANN model due to its ability to take into account both individual and interactive effects. The rod promoters were found to be more effective in reducing bed fluctuation, and in increasing bed expansion at high gas mass velocities.

  19. Particle agglomeration during energy recovery from plastic wastes by means of fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Arena, U.; Mastellone, M.L.

    1999-07-01

    The occurrence and the significance of agglomeration phenomena during thermal treatments in a fluidized bed reactor of a couple of plastic wastes were studied. A small scale bubbling fluidized bed, made of quartz, was charged with pellets obtained from mono-material collections of polyethylene and polyethylene terephtalate. Batchwise and continuous experiments were carried out at different bed temperatures (from 450 to 850 C), under inert and oxidizing conditions and by operating the reactor with silica sand having a size range of 0.3--0.4 mm. Different mechanisms of defluidization were identified and characterized. The time at which the phenomena occurred, for each of bed temperatures used, was also determined. In particular, the continuous experiments showed that defluidization can occur, with different mechanisms, at temperatures lower than 850 C. An increase of bed temperature as well as that of oxygen content strongly reduces the potential concern of particle agglomeration and bed defluidization.

  20. Flow structure of the solids in a 3-D gas-liquid-solid fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Larachi, F.; Cassanello, M.; Chaouki, J.; Guy, C. [Ecole Polytechnique, Montreal, Quebec (Canada). Dept. of Chemical Engineering

    1996-09-01

    Gas-liquid-solid fluidized systems have made inroads into a variety of industrial applications from heavy oil, petroleum resid, and synthetic crude processing to fermentation and aerobic biological wastewater treatment. Local and macroscopic solids flow structure and kinematics in a 3-D gas-liquid-solid fluidized bed were studied using a noninvasive radioactive-particle tracking (RPT) technique. Based on the multisite detection of {gamma} radiations emitted from a single radiolabeled tracer particle freely moving in the fluidized bed, RPT permitted the authors to obtain fast sampling of 3-D trajectories of the tracer, whose physical properties were similar to those of the solids inventory. These trajectories showed the detailed motion sequences of the solid particles as entrained in the bubble wakes, fluctuating randomly or sinking deterministically in the liquid-solid emulsion. Based on measurements done in the vortical-spiral flow regime, the dynamic solids flow structure inside a three-phase fluidized bed can be viewed as a three-zone core-annulus-annulus structure: a central fast-bubble flow region with the particles swirling upward; a vortical flow region around the velocity inversion point with the particles momentarily captured in emulsion vortices; and a relatively bubble-free descending flow region where the particles spiral down between the velocity inversion point and vessel walls. The flow structure of dense fluidized beds are similar to the flow structure of liquid and/or solid in lean fluidized beds. Measured distributions of local ensemble-averaged particle velocities and turbulence intensities were consistent with the existence of a toroidal recirculatory solids flow pattern in the bed. Measured mean circumferential ensemble-averaged radial velocity was essentially zero throughout most of the bed. The solids flow turbulence field was nonisotropic, as radial turbulence intensities were generally lower than longitudinal turbulence intensities.

  1. Fluidized bed as a solid precursor delivery system in a chemical vapor deposition reactor

    OpenAIRE

    Vahlas, Constantin; Caussat, Brigitte; Senocq, François; Gladfelter, Wayne L.; Sarantopoulos, Christos; Toro, David; Moersch, Tyler

    2005-01-01

    Chemical vapor deposition (CVD) using precursors that are solids at operating temperatures and pressures, presents challenges due to their relatively low vapor pressures. In addition, the sublimation rates of solid state precursors in fixed bed reactors vary with particle and bed morphology. In a recent patent application, the use of fluidized bed (FB) technology has been proposed to provide high, reliable, and reproducible flux of such precursors in CVD processes. In the present contribution...

  2. Experimental investigation of thermal conductivity coefficient and heat exchange between fluidized bed and inclined exchange surface

    Directory of Open Access Journals (Sweden)

    B. Stojanovic

    2009-06-01

    Full Text Available The paper presents experimental research of thermal conductivity coefficients of the siliceous sand bed fluidized by air and an experimental investigation of the particle size influence on the heat transfer coefficient between fluidized bed and inclined exchange surfaces. The measurements were performed for the specific fluidization velocity and sand particle diameters d p=0.3, 0.5, 0.9 mm. The industrial use of fluidized beds has been increasing rapidly in the past 20 years owing to their useful characteristics. One of the outstanding characteristics of a fluidized bed is that it tends to maintain a uniform temperature even with nonuniform heat release. On the basis of experimental research, the influence of the process's operational parameters on the obtained values of the bed's thermal conductivity has been analyzed. The results show direct dependence of thermal conductivity on the intensity of mixing, the degree of fluidization, and the size of particles. In the axial direction, the coefficients that have been treated have values a whole order higher than in the radial direction. Comparison of experimental research results with experimental results of other authors shows good agreement and the same tendency of thermal conductivity change. It is well known in the literature that the value of the heat transfer coefficient is the highest in the horizontal and the smallest in the vertical position of the heat exchange surface. Variation of heat transfer, depending on inclination angle is not examined in detail. The difference between the values of the relative heat transfer coefficient between vertical and horizontal heater position for all particle sizes reduces by approximately 15% with the increase of fluidization rate.

  3. High temperature degradation by erosion-corrosion in bubbling fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Peggy Y.; MacAdam, S.; Niu, Y.; Stringer, J.

    2003-04-22

    Heat-exchanger tubes in fluidized bed combustors (FBCs) often suffer material loss due to combined corrosion and erosion. Most severe damage is believed to be caused by the impact of dense packets of bed material on the lower parts of the tubes. In order to understand this phenomenon, a unique laboratory test rig at Berkeley was designed to simulate the particle hammering interactions between in-bed particles and tubes in bubbling fluidized bed combustors. In this design, a rod shaped specimen is actuated a short distance within a partially fluidized bed. The downward specimen motion is controlled to produce similar frequencies, velocities and impact forces as those experienced by the impacting particle aggregates in practical systems. Room temperature studies have shown that the degradation mechanism is a three-body abrasion process. This paper describes the characteristics of this test rig, reviews results at elevated temperatures and compares them to field experience. At higher temperatures, deposits of the bed material on tube surfaces can act as a protective layer. The deposition depended strongly on the type of bed material, the degree of tube surface oxidation and the tube and bed temperatures. With HCl present in the bed, wastage was increased due to enhanced oxidation and reduced oxide scale adherence.

  4. Metal wastage design guidelines for bubbling fluidized-bed combustors. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Lyczkowski, R.W.; Podolski, W.F.; Bouillard, J.X.; Folga, S.M. [Argonne National Lab., IL (United States)

    1992-11-01

    These metal wastage design guidelines identify relationships between metal wastage and (1) design parameters (such as tube size, tube spacing and pitch, tube bundle and fluidized-bed height to distributor, and heat exchanger tube material properties) and (2) operating parameters (such as fluidizing velocity, particle size, particle hardness, and angularity). The guidelines are of both a quantitative and qualitative nature. Simplified mechanistic models are described, which account for the essential hydrodynamics and metal wastage processes occurring in bubbling fluidized beds. The empirical correlational approach complements the use of these models in the development of these design guidelines. Data used for model and guideline validation are summarized and referenced. Sample calculations and recommended design procedures are included. The influences of dependent variables on metal wastage, such as solids velocity, bubble size, and in-bed pressure fluctuations, are discussed.

  5. Development of a bioreactor based on magnetically stabilized fluidized bed for bioartificial liver.

    Science.gov (United States)

    Deng, Fei; Chen, Li; Zhang, Ying; Zhao, Shan; Wang, Yu; Li, Na; Li, Shen; Guo, Xin; Ma, Xiaojun

    2015-12-01

    Bioartificial liver (BAL) based on microcapsules has been proposed as a potential treatment for acute liver failure. The bioreactors used in such BAL are usually expected to achieve sufficient flow rate and minimized void volume for effective application. Due to the superiorities in bed pressure drop and operation velocity, magnetically stabilized fluidized beds (MSFBs) show the potential to serve as ideal microcapsule-based bioreactors. In the present study, we attempted to develop a microcapsule-based MSFB bioreactor for bioartificial liver device. Compared to conventional-fluidized bed bioreactors, the bioreactor presented here increased perfusion velocity and decreased void volume significantly. Meanwhile, the mechanical stability as well as the immunoisolation property of magnetite microcapsules were well maintained during the fluidization. Besides, the magnetite microcapsules were found no toxicity to cell survival. Therefore, our study might provide a novel approach for the design of microcapsule-based bioartificial liver bioreactors.

  6. Evaluation of wall boundary condition parameters for gas-solids fluidized bed simulations

    Energy Technology Data Exchange (ETDEWEB)

    Li, Tingwen [URS Corporation; Morgantown, WV (United States); National Energy Technology Lab. (NETL), Morgantown, WV (United States); Benyahia, Sofiane [National Energy Technology Lab. (NETL), Morgantown, WV (United States)

    2013-10-01

    Wall boundary conditions for the solids phase have significant effects on numerical predictions of various gas-solids fluidized beds. Several models for the granular flow wall boundary condition are available in the open literature for numerical modeling of gas-solids flow. In this study, a model for specularity coefficient used in Johnson and Jackson boundary conditions by Li and Benyahia (AIChE Journal, 2012, 58, 2058-2068) is implemented in the open-source CFD code-MFIX. The variable specularity coefficient model provides a physical way to calculate the specularity coefficient needed by the partial-slip boundary conditions for the solids phase. Through a series of 2-D numerical simulations of bubbling fluidized bed and circulating fluidized bed riser, the model predicts qualitatively consistent trends to the previous studies. Furthermore, a quantitative comparison is conducted between numerical results of variable and constant specularity coefficients to investigate the effect of spatial and temporal variations in specularity coefficient.

  7. ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Wei-Ping Pan; Andy Wu; John T. Riley

    2004-10-30

    This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period July 1, 2004 through September 30, 2004. The following tasks have been completed. First, renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have started. Second, the design if the component parts of the CFBC system have been reviewed and finalized so that the drawings may be released to the manufacturers during the next quarter. Third, the experiments for solid waste (chicken litter) incineration have been conducted using a Thermogravimetric Analyzer (TGA). This is in preparation for testing in the simulated fluidized-bed combustor. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter has been outlined in this report.

  8. Rivesville multicell fluidized bed boiler. Annual technical progress report. July 1978-June 1979

    Energy Technology Data Exchange (ETDEWEB)

    1980-08-01

    Design, construction and test program of a 300,000 lb/hr steam generating capacity multicell fluidized bed boiler (MFB), as a pollution free method of burning high-sulfur or highly corrosive coals, is being carried out. The concept involves burning fuels such as coal, in a fluidized bed of limestone particles that react with the sulfur compounds formed during combustion to reduce air pollution. Nitrogen oxide emissions are also reduced at the lower combustion temperatures. The CaSO/sub 4/ produced in the furnace is discharged with the ash or regenerated to CaO for reuse in the fluidized bed. Information is presented on continued operation of the Rivesville MFB steam generating plant in a commercial mode and for determining performance and emission characteristics; studies and tests on flyash characterization and reinjection, fuel feed eductors and needles, air distributor, corrosion-erosion and sulfur capture; engineering studies to improve MFB performance and reliability.

  9. Operation of magnetically assisted fluidized beds in microgravity and variable gravity: experiment and theory

    Science.gov (United States)

    Sornchamni, T.; Jovanovic, G. N.; Reed, B. P.; Atwater, J. E.; Akse, J. R.; Wheeler, R. R.

    2004-01-01

    The conversion of solid waste into useful resources in support of long duration manned missions in space presents serious technological challenges. Several technologies, including supercritical water oxidation, microwave powered combustion and fluidized bed incineration, have been tested for the conversion of solid waste. However, none of these technologies are compatible with microgravity or hypogravity operating conditions. In this paper, we present the gradient magnetically assisted fluidized bed (G-MAFB) as a promising operating platform for fluidized bed operations in the space environment. Our experimental and theoretical work has resulted in both the development of a theoretical model based on fundamental principles for the design of the G-MAFB, and also the practical implementation of the G-MAFB in the filtration and destruction of solid biomass waste particles from liquid streams.

  10. MULTI-SCALE AGGREGATION OF PARTICLES IN GAS-SOLIDS FLUIDIZED BEDS

    Institute of Scientific and Technical Information of China (English)

    Hongzhong Li

    2004-01-01

    The multi-scale characteristics of clusters in a fast fluidized bed and of agglomerates in a fluidized bed of cohesive particles are discussed on the basis of large amounts of experiments. The cluster size and concentration are dominated by the local voidage of the bed. A cluster consists of many sub-clusters with different sizes and discrete particles, and the sub-cluster size probability density distribution appears as a negative exponential function. The agglomerates in a fluidized bed of cohesive particles also possess the multi-scale nature. The large agglomerates form a fixed bed at the bottom, the medium agglomerates are fluidized in the middle, and the small agglomerates and discrete particles become the dilute-phase region in the upper part of the bed. The agglomerate size is mainly affected by cohesive forces and gas velocity. The present models for predicting the size of clusters and agglomerates can not tackle the intrinsic mechanism of the multi-scale aggregation, and a challenging problem for establishing mechanistic model is put forward.

  11. Moving Behavior of an Object in Gas-Solid Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    WEI Lu-bin; WANG Geng-yu; HAO Liang; ZHAO Yue-min

    2005-01-01

    The settling behavior of coarse particles in a gas-solid fluidized bed was experimentally studied by using magnetic tracer. It is well known that the calculation of terminal velocity is of interest in dense medium separation.However, this problem has not been completely solved up to now. In this work, the terminal velocity of an object moving in a gas-solid fluidized bed was experimentally measured and theoretically calculated. The experimental results in dicated that the plastic viscosity and yield stress of the bed increase as the size of fluidized particles increases, but it varies little when some coarser particles are mixed with the fluidized particles. The resistance to a rising object was an order magnitude greater than that to a settling object. The efficient buoyancy on a flaky object, which lies flatly on the gas distributor, was much less than that calculated by the Archimedes' principle. The object does not always rise or set tle with minimal projective area owing to radial motion of the fluidized particles. But in the lower part of the bed, the bar-shaped objects were likely with minimal projective area rising or settling.

  12. Modeling of structural effects in biomedical elements after titanium oxidation in fluidized bed

    Directory of Open Access Journals (Sweden)

    Mendzik K.

    2010-06-01

    Full Text Available Oxidation is one of the most employed methods to improve titanium and its alloys properties especially due to medical application. This process like most of the thermochemical treatment processes substantially influences on the characteristic of surface layers and the same on its mechanical and useful properties. Oxide coatings produced during titanium oxidation were examined due to their composition identification. Titanium was oxidized in fluidized bed in temperature range between 500÷700°C. Microstructures of titanium with a visible oxide coating on its surface after thermochemical treatment and changes of grain size in core of titanium samples are described. Moreover Xray phase analysis of obtained oxides coatings was made as well as microhardness measurements of titanium surface layers after oxidation process. Finally, the surfaces of titanium after oxidation in fluidized bed were measured by Auger electron spectroscopy. All research results are used to built numerical model of oxidation process in fluidized. Titanium oxidation process in fluidized bed is very complicated, because changes of parameters are non linear characteristics. This fact and lack of mathematical algorithms describing this process makes modeling properties of titanium elements by traditional numerical methods difficult or even impossible. In this case it is possible to try using artificial neural network. Using neural networks for modeling oxidizing in fluidized bed is caused by several nets' features: non linear character, ability to generalize the results of calculations for data out of training set, no need for mathematical algorithms describing influence changes input parameters on modeling materials properties.

  13. The influence of fine char particles burnout on bed agglomeration during the fluidized bed combustion of a biomass fuel

    Energy Technology Data Exchange (ETDEWEB)

    Scala, Fabrizio; Chirone, Riccardo [Istituto di Ricerche sulla Combustione, CNR, P.le V. Tecchio, 80-80125 Naples (Italy); Salatino, Piero [Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, P.le V. Tecchio, 80-80125 Naples (Italy)

    2003-11-15

    The combustion of biomass char in a bubbling fluidized bed is hereby addressed, with specific reference to the influence that the combustion of fine char particles may exert on ash deposition and bed agglomeration phenomena. Experiments of steady fluidized bed combustion (FBC) of powdered biomass were carried out with the aim of mimicking the postcombustion of attrited char fines generated in the fluidized bed combustion of coarse char. Experimental results showed that the char elutriation rate is much smaller than expected on the basis of the average size of the biomass powder and of the carbon loading in the combustor. Samples of bed material collected after prolonged operation of the combustor were characterized by scanning electron microscopy (SEM)-EDX analysis and revealed the formation of relatively coarse sand-ash-carbon aggregates. The phenomenology is consistent with the establishment of a char phase attached to the bed material as a consequence of adhesion of char fines onto the sand particles. Combustion under sound-assisted fluidization conditions was also tested. As expected, enhancement of fines adhesion on bed material and further reduction of the elutriation rate were observed. Experimental results are interpreted in the light of a simple model which accounts for elutriation of free fines, adhesion of free fines onto bed material and detachment of attached fines by attrition of char-sand aggregates. Combustion of both free and attached char fines is considered. The parameters of the model are assessed on the basis of the measured carbon loadings and elutriation rates. Model computations are directed to estimate the effective size and the peak temperature of char-sand aggregates. The theoretical estimates of the effective aggregate size match fairly well those observed in the experiments.

  14. Comparison of fibre optical measurements and discrete element simulations for the study of granulation in a spout fluidized bed

    NARCIS (Netherlands)

    Link, J.M.; Godlieb, W.; Tripp, P.; Deen, N.G.; Heinrich, S.; Kuipers, J.A.M.; Schönherr, M.; Peglow, M.

    2009-01-01

    Spout fluidized beds are frequently used for the production of granules or particles through granulation. The products find application in a large variety of applications, for example detergents, fertilizers, pharmaceuticals and food. Spout fluidized beds have a number of advantageous properties, su

  15. Development and application of a procedure for evaluating the long-term integrity of membranes for the anaerobic fluidized membrane bioreactor (AFMBR).

    Science.gov (United States)

    Shin, Chungheon; Kim, Kihyun; McCarty, Perry L; Kim, Jeonghwan; Bae, Jaeho

    2016-01-01

    A bench-scale short-term test, developed to predict the long-term integrity of membranes with potential for use in anaerobic fluidized-bed membrane bioreactors, was used to evaluate several commercial hollow-fiber membranes. It was found that membrane performance varied widely, some membranes failing much more rapidly than others. Also found was that larger sizes of the fluidized media, in this case granular activated carbon (GAC), severely affected membrane structural integrity more than did smaller sizes, as did the method used for membrane attachment. Within the limits studied, the GAC packing ratio had only a minor impact. A decrease in membrane permeability that sometimes resulted during the testing and was caused by the deposition of fine GAC particles could be eliminated without membrane damage through simultaneous chemical cleaning and sonication. This new testing procedure should be useful for selecting membranes and reactor operating conditions to better ensure long-term operating performance of anaerobic fluidized-bed membrane bioreactors. PMID:27438251

  16. Combined gas-steam power stations with pressurized fluidized bed combustion (PFBC) of coal

    Energy Technology Data Exchange (ETDEWEB)

    Grzegorczyk, W. (Energoprojekt, Warsaw (Poland))

    1990-11-01

    Presents pressurized fluidized bed combustion (PFBC) of coal that combines fluidized bed combustion with two-agent gas-steam circulation. PFBC permits clean combustion of coal with low calorific value and high ash and sulfur content. The ABB company offered a block for the Pruszkow power plant in Poland. Specifications of the block are given as: thermal power in fuel 430 MW and electrical power 175 MW. The boiler, gas turbine and turbine set are described. Technical and economic indices are given. The supplier attests that the emission values of 70 mg sulfur dioxide per MJ and 120 mg of nitrogen dioxide will not be exceeded under normal conditions.

  17. Cocurrent downflow circulating fluidized bed (downer) reactors - a state of the art review

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, J.-X.; Yu, Z.-Q.; Jin, Y.; Grace, J.R.; Issangya, A. [University of Western Ontario, London, ON (Canada). Department of Chemical and Biochemical Engineering

    1995-10-01

    A new type of chemical reactor known as the cocurrent downflow fluidized bed reactor (or reversed riser reactor or downer reactor), that overcomes some of the disadvantages of the riser reactor, is described. Since both the gas and solids flow directions are downwards in the cocurrent downflow fluidized bed reactor, particle residence times are uniform, and there is no backmixing. The literature on downer studies is reviewed. Laboratory results on axial voidage profiles, pressure profiles, radial flow, mixing and residence time distribution, heat transfer, and particle velocities are summarized. Suggestions are made both for possible industrial applications of downer reactors and for suitable research directions. 56 refs., 18 figs., 1 tab.

  18. Refractory experience in circulating fluidized bed combustors, Task 7. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Vincent, R.Q.

    1989-11-01

    This report describes the results of an investigation into the status of the design and selection of refractory materials for coal-fueled circulating fluidized-bed combustors. The survey concentrated on operating units in the United States manufactured by six different boiler vendors: Babcock and Wilcox, Combustion Engineering, Foster Wheeler, Keeler Dorr-Oliver, Pyropower, and Riley Stoker. Information was obtained from the boiler vendors, refractory suppliers and installers, and the owners/operators of over forty units. This work is in support of DOE`s Clean Coal Technology program, which includes circulating fluidized-bed technology as one of the selected concepts being evaluated.

  19. Experiment research on grain drying process in the heat pump assisted fluidized beds

    Institute of Scientific and Technical Information of China (English)

    Jing Yang; Li Wang; Fi Xiang; Lige Tong; Hua Su

    2004-01-01

    A heat pump assisted fluidized bed grain drying experimental system was developed. Based on this system, a serial of experiments was performed under four kinds of air cycle conditions. According to the experimental analysis, an appropriate drying medium-air cycle for the heat pump assisted fluidized bed drying equipment was decided, which is different from the commonly used heat pump assisted drying system. The experimental results concerning the drying operation performance of the new system show that the averaged coefficient of performance (COP) can reach more than 2.5. The economical evaluation was performed and the powefficiency and great application potentiality in future market.

  20. Biological fluidized-bed treatment of groundwater from a manufactured gas plant site

    International Nuclear Information System (INIS)

    Bench- and pilot-scale biological treatability studies were performed as part of a comprehensive study for developing an on-site treatment system for contaminated groundwater at a former manufactured gas plant site. The bench-scale work, which included evaluations of activated sludge and fluidized-bed biological processes, indicated that a carbon-based fluidized-bed process was most appropriate. The process was then demonstrated on a pilot level at the site. The bench and pilot studies demonstrated significant reductions of chemical oxygen demand (COD), and all target organics including polycyclic aromatic hydrocarbons (PAHs) and volatile organic compounds (VOCs)

  1. Application of fluidized-bed technology to the recovery of waste heat

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, G.J.; Grogan, P.J.; Evans, A.R.

    1979-08-01

    The fluidized-bed, waste-heat boiler (FBWHB) may represent a significant opportunity for industrial energy conservation. The applications of FBWHBs to the recovery of heat from waste streams are examined. Compared to other waste-heat recovery units, FBWHBs can transfer more heat per unit volume and are physically smaller - an important consideration for retrofit and construction costs. A detailed discussion of fluidized beds, including their application in waste-heat recovery and the factors affecting FBWHB design is presented. Design methodology is discussed along with a preliminary engineering design for recovering heat from a waste-gas stream, a typical FBWHB application.

  2. A Novel Atmospheric Pressure Plasma Fluidized Bed and Its Application in Mutation of Plant Seeds

    Institute of Scientific and Technical Information of China (English)

    CHEN Guang-Liang; WANG Zhen-Quan; HAN Er-Li; FU Ya-Bo; YANG Si-Ze; FAN Song-Hua; LI Chun-Ling; GU Wei-Chao; FENG Wen-Ran; ZHANG Gu-Ling; WANG Jiu-Li; Latif K.; ZHANG Shu-Gen

    2005-01-01

    @@ An atmospheric pressure plasma fluidized bed (APPFB) is designed to generate plasma using a dielectric barrier discharge (DBD) with one liquid electrode. In the APPFB system, the physical properties of DBD discharge and its application in plant-seed mutating are studied fundamentally. The results show that the generated plasma is a typical glow discharge free from filament and arc plasma, and the macro-temperature of the plasma fluidized bed is nearly at room temperature. There are no obvious changes in the pimientos when their seeds are treated by APPFB, but great changes are found for coxcombs.

  3. STUDY ON THE OVERALL PRESSURE BALANCE OF A DOWNFLOW CIRCULATING FLUIDIZED BED SYSTEM

    Institute of Scientific and Technical Information of China (English)

    Hengzhi Chen; Dawei Yang; Hongzhong Li; Shiyu Tan

    2006-01-01

    A pressure balance model for a circulating fluidized bed unit that incorporates a downer has been proposed. The model predictions were validated with the experimental data obtained from a special cold-model circulating fluidized bed. Comparison of the operation stability between a CFB downer and a CFB riser has been carried out. Only one critical gas velocity exists in the CFB-riser for a given riser solids flux, while there can be many critical gas velocities for the operation of a CFB downer. Therefore, it is possible to achieve high solids concentration in a CFB downer if appropriate operating conditions are used.

  4. Reduction and Immobilization of Potassium Permanganate on Iron Oxide Catalyst by Fluidized-Bed Crystallization Technology

    OpenAIRE

    Guang-Xia Li; Yao-Hui Huaug; Teng-Chien Chen; Yu-Jen Shih; Hui Zhang

    2012-01-01

    A manganese immobilization technology in a fluidized-bed reactor (FBR) was developed by using a waste iron oxide (i.e., BT-3) as catalyst which is a by-product from the fluidized-bed Fenton reaction (FBR-Fenton). It was found that BT-3 could easily reduce potassium permanganate (KMnO4) to MnO2. Furthermore, MnO2 could accumulate on the surface of BT-3 catalyst to form a new Fe-Mn oxide. Laboratory experiments were carried out to investigate the KMnO4-reduction mechanism, including the effect ...

  5. Effect of Microwave on Fluidized Bed Drying of Beetroot (Beta vulgaris L.)

    OpenAIRE

    Yashwant Kumar; Mohammad Ali Khan; Krishna Kumar Patel

    2016-01-01

    In the present work, an attempt has been made to study the effect of inlet air temperature and velocity on the drying characteristics of beetroot’s (Beta vulgaris L.) pieces in microwave assisted fluidized bed drying (MAFBD) system. The results were compared with samples of beetroot dried in a fluidized bed dryer (FBD) at the same combination of temperatures and air velocities. The selected inlet air temperatures and inlet air velocities were 60°C, 67.50°C and 75°C and 9 m/s, 10.50 m/s and 12...

  6. Hydrodynamic study on gasification of biomass in a fluidized bed gasifier

    Directory of Open Access Journals (Sweden)

    S.BASKARA SETHUPATHY

    2012-01-01

    Full Text Available Current scenario of energy insecurity urges us to realize the importance of alternate energy sources. In country with variety of vegetation like India, Biomass finds its place of which fluidized bed gasification of biomass could be more effective. This paper emphasizes the importance of a fluidized bed gasifier for energy conversion of agro-residues for useful purposes. Coconut Shell and Ground nut shell of gross calorific value 19.43MJ/kg and 14.91 MJ/kg respectively are taken for the study. The particle size is restricted not to exceed 3mm. Various empirical correlations involved in fluidization are studied and their interdependence is detailed. From various published data, importance of inert materials and their relative proportions with biomass fuels are studied and optimum biomass to sand ratio is fixed as 10 to 15% by mass. Equations for predicting the minimum fluidization velocities of these mixtures are also discussed. Variations of Fluidization parameters such asminimum fluidization velocity, bubble rise velocity, expanded bed height with respect to temperature, equivalence ratio, particle size is studied and their quantification is analyzed. A 108 mm internal diameter and 1400 mm high FBG is used for the study. Fuel is fed through screw feeder and air is supplied through blower. In the down stream side cyclone separator is placed after which the sampling and burner lines are connected. A regression model is developed and the feasibility of gasifying coconut shell and groundnut shell are discussed. Earlier and present work of coconut shell gasification proves fluidized bed gasification is more appropriate for agro residues.

  7. FLUIDIZED BED STEAM REFORMER (FBSR) PRODUCT: MONOLITH FORMATION AND CHARACTERIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-09-13

    The most important requirement for Hanford's low activity waste (LAW) form for shallow land disposal is the chemical durability of the product. A secondary, but still essential specification, is the compressive strength of the material with regards to the strength of the material under shallow land disposal conditions, e.g. the weight of soil overburden and potential intrusion by future generations, because the term ''near-surface disposal'' indicates disposal in the uppermost portion, or approximately the top 30 meters, of the earth's surface. The THOR{reg_sign} Treatment Technologies (TTT) mineral waste form for LAW is granular in nature because it is formed by Fluidized Bed Steam Reforming (FBSR). As a granular product it has been shown to be as durable as Hanford's LAW glass during testing with ASTM C-1285-02 known as the Product Consistency Test (PCT) and with the Single Pass Flow Through Test (SPFT). Hanford Envelope A and Envelope C simulants both performed well during PCT and SPFT testing and during subsequent performance assessment modeling. This is partially due to the high aluminosilicate content of the mineral product which provides a natural aluminosilicate buffering mechanism that inhibits leaching and is known to occur in naturally occurring aluminosilicate mineral analogs. In order for the TTT Na-Al-Si (NAS) granular mineral product to meet the compressive strength requirements (ASTM C39) for a Hanford waste form, the granular product needs to be made into a monolith or disposed of in High Integrity Containers (HIC's). Additionally, the Hanford intruder scenario for disposal in the Immobilized Low Activity Waste (ILAW) trench is mitigated as there is reduced intruder exposure when a waste form is in a monolithic form. During the preliminary testing of a monolith binder for TTT's FBSR mineral product, four parameters were monitored: (1) waste loading (not optimized for each waste form tested); (2) density

  8. Hydrodynamics of a fluidized bed co-combustor for tobacco waste and coal.

    Science.gov (United States)

    Zhang, Kai; Yu, Bangting; Chang, Jian; Wu, Guiying; Wang, Tengda; Wen, Dongsheng

    2012-09-01

    The fluidization characteristics of binary mixtures containing tobacco stem (TS) and cation exchange resin (a substitute for coal) were studied in a rectangular bed with the cross-section area of 0.3 × 0.025 m(2). The presence of herbaceous biomass particles and their unique properties such as low density and high aspect ratio resulted in different fluidization behaviors. Three fluidization velocities, i.e. initial, minimum and full fluidization velocities, were observed as the TS mass fraction increased from 7% to 20%, and four hydrodynamic stages were experienced, including the static, segregation, transition and mixing stages, with increasing operational gas velocities. The results suggest that the operational gas velocity should be in the range of 2.0-5.0 times of the minimum fluidization velocity of the binary mixtures, and less than 7% TS mass fraction should be used in an existing bubbling fluidized bed. Higher TS fraction inclusion requires the introduction of central jet gas to improve the mixing effect. PMID:22750501

  9. Dual-Fuel Fluidized Bed Combustor Prototype for Residential Heating: Steady-State and Dynamic Behavior

    Science.gov (United States)

    Cammarota, Antonio; Chirone, Riccardo; Miccio, Michele; Sollmene, Roberto; Urcluohr, Massimo

    Fluidized bed combustion of biogenic fuels can be recognized as an attractive option for an ecologically sustainable use of biofuels in residential applications. Nevertheless, biomass combustion in fluidized bed reactors presents some drawbacks that are mainly related to mixing/segregation of fuel particles/volatile matter during devolatilization inside the bed and in the freeboard or to bed agglomeration. A prototype of a 30-50 kWth fluidized bed boiler for residential heating has been designed to burn either a gaseous combustible or a solid biomass fuel or both fuels at the same time. The prototype has been equipped with a gas burner located in the wind-box to optimize the start-up stage of the boiler and with a fluidized bed characterized by a conical geometry ("Gulf Stream" circulation) to improve the mixing of the fuel particles during both devolatilization and char burn-out. The operation of the combustor adopting wood pellets as fuel has been investigated to evaluate their use in residential combustion applications. Steady-state thermally stable regimes of operation have been recognized analyzing both boiler temperatures and gaseous emissions. The optimization of the steady-state operation of the boiler in terms of gaseous emissions has been achieved by varying the nominal thermal power and air excess. An ad-hoc experimental campaign has been carried out to analyze the dynamic performance of the prototype as a response to changes of the demanded thermal power. On the basis of the experimental data, an interpretation of the dynamic behavior of the fluidized bed boiler has been proposed.

  10. Emissions from multiple-spouted and spout-fluid fluidized beds using rice husks as fuel

    Energy Technology Data Exchange (ETDEWEB)

    Albina, D.O. [School of Engineering and Architecture, Mindanao Polytechnic State College, Cagayan de Oro City 9000 (Philippines)

    2006-10-15

    This paper presents the experimental results of the emissions of CO and CO{sub 2} using rice husks as fuel on different configurations of spout-fluidized beds namely, multiple-spouted and spout-fluid fluidized bed. The emission of pollutants from the multiple-spouted bed and spout-fluid bed was investigated with rice husk fuel. The operating parameters considered were the different levels of excess air, different primary-to-secondary air ratios at each level of excess air and method of feeding. It was found that emission of CO from the multiple-spouted bed seemed to be lower with under-bed feeding of the rice husk fuel compared to over-bed feeding. However, the emission of CO{sub 2} did not change significantly for both methods of feeding. Changes in excess air levels influenced the emissions of CO and CO{sub 2} from the multiple-spouted bed within the excess air range investigated. It was found that emission of CO was less at 10% excess air with over-bed feeding; emission of CO in the case of under-bed feeding was lowest at 20% excess air level. It was found that the method of feeding had not significantly influenced the emission of CO and CO{sub 2} in the spout-fluid bed. The combustion efficiency however, in general, was slightly higher in the case of under-bed feeding compared to over-bed feeding. Emission of CO was less in the spout-fluid bed compared with the emission of CO in the multiple-spouted bed. The result can be likely attributed to the higher combustion efficiency attained by the spout-fluid bed compared with that of multiple-spouted bed. (author)

  11. Case studies--Problem solving in fluidized bed waste fuel incineration

    International Nuclear Information System (INIS)

    Fluidized bed combustion technology has been widely used as the new, flexible, multi-fuel boiler for waste combustion and energy recovery from low grade fuels. However, problems such as low thermal efficiency, high emissions, bed agglomeration etc. are still encountered in the operation of fluidized beds. Valuable experiences were gained from two case studies recently conducted regarding wastes combustion in industrial scale fluidized beds. In the first case, the performance of a fluidized bed combustor for energy recovery from oil sludge was evaluated during the commissioning trials. Apart from the sludge characterization and bed material analysis, the combustion efficiency, solid flow balance and on stack emission of CO, SOx and NOx were investigated, as well as the fluidization quality. Although the system was operated with good combustion efficiency (>99.9%), sulfur dioxide emission (>1000 ppm) was found to be substantially higher than the allowable discharge limit. It was recommended to increase the limestone feed rate in order to meet the SO2 emission standard, and subsequently, installation of a cyclone is suggested to remove the potentially significant increase in ash and fine particles. The second case study focused on the bed agglomeration observed in a fluidized bed incinerator where a burning blend of three wastes (i.e. carbon soot, bio sludge and fuel oil) is involved. To understand the mechanisms and related chemistry, several analytical approaches are employed to identify the bed materials (fresh sand and degrader sand) and the clinkers formed from full scale incinerator tests. The formation of clinker is believed to follow the mechanism of partial melting and/or reactive liquid sintering. The effects of temperature and blending ratio are tested in a muffle furnace. Carbon soot is believed to be more susceptible than the other two fuels. Thermodynamic multi-phase multi-component equilibrium (Tce) calculations predict that the main low melting point

  12. Riser simulation and radial porosity distribution characterization for gas-fluidized bed of cork particles

    Science.gov (United States)

    Wu, Guorong; Ouyang, Jie; Li, Qiang

    2014-08-01

    Numerical simulations are carried out for gas-solid fluidized bed of cork particles, using discrete element method. Results exhibit the existence of a so-called anti core-annular porosity profile with lower porosity in the core and higher porosity near the wall for non-slugging fluidization. The tendency to form this unfamiliar anti core-annular porosity profile is stronger when the solid flux is higher. There exist multiple inflection points in the simulated axial solid volume fraction profile for non-slugging fluidization. Results also show that the familiar core-annular porosity profile still appears for slugging fluidization. In addition, the classical choking phenomenon can be captured at the superficial gas velocity slightly lower than the correlated transport velocity.

  13. ADVANCED SORBENT DEVELOPMENT PROGRAM DEVELOPMENT OF SORBENTS FOR MOVING-BED AND FLUIDIZED-BED APPLICATIONS

    Energy Technology Data Exchange (ETDEWEB)

    R.E Ayala; V.S. Venkataramani; Javad Abbasian; Rachid B. Slimane; Brett E. Williams; Minoo K. Zarnegar; James R. Wangerow; Andy H. Hill

    2000-03-31

    The integrated gasification combined cycle (IGCC) power system using high-temperature coal gas cleanup is one of the most promising advanced technologies for the production of electric power from coal in an environmentally acceptable manner. Unlike conventional low-temperature cleanup systems that require costly heat exchangers, high-temperature coal gas cleanup systems can be operated near 482-538 C (900-1000 F) or higher, conditions that are a closer match with the gasifier and turbine components in the IGCC system, thus resulting is a more efficient overall system. GE is developing a moving-bed, high-temperature desulfurization system for the IGCC power cycle in which zinc-based regenerable sorbents are currently being used as desulfurization sorbents. Zinc titanate and other proprietary zinc-based oxides are being considered as sorbents for use in the Clean Coal Technology Demonstration Program at Tampa Electric Co.'s (TECo) Polk Power Station. Under cold startup conditions at TECo, desulfurization and regeneration may be carried out at temperatures as low as 343 C (650 F), hence a versatile sorbent is desirable to perform over this wide temperature range. A key to success in the development of high-temperature desulfurization systems is the matching of sorbent properties for the selected process operating conditions, namely, sustainable desulfurization kinetics, high sulfur capacity, and mechanical durability over multiple cycles. Additionally, the sulfur species produced during regeneration of the sorbent must be in a form compatible with sulfur recovery systems, such as sulfuric acid or elemental sulfur processes. The overall objective of this program is to develop regenerable sorbents for hydrogen sulfide removal from coal-derived fuel gases in the temperature range 343-538 C (650-1000 F). Two categories of reactor configurations are being considered: moving-bed reactors and fluidized-bed (bubbling and circulating) reactors. In addition, a cost

  14. Advanced sorbent development progam; development of sorbents for moving-bed and fluidized-bed applications

    International Nuclear Information System (INIS)

    The integrated gasification combined cycle (IGCC) power system using high-temperature coal gas cleanup is one of the most promising advanced technologies for the production of electric power from coal in an environmentally acceptable manner. Unlike conventional low-temperature cleanup systems that require costly heat exchangers, high-temperature coal gas cleanup systems can be operated near 482-538 C (900-1000F) or higher, conditions that are a closer match with the gasifier and turbine components in the IGCC system, thus resulting is a more efficient overall system. GE is developing a moving-bed, high-temperature desulfurization system for the IGCC power cycle in which zinc-based regenerable sorbents are currently being used as desulfurization sorbents. Zinc titanate and other proprietary zinc-based oxides are being considered as sorbents for use in the Clean Coal Technology Demonstration Program at Tampa Electric Co.s (TECo) Polk Power Station. Under cold startup conditions at TECo, desulfurization and regeneration may be carried out at temperatures as low as 343 C (650 F), hence a versatile sorbent is desirable to perform over this wide temperature range. A key to success in the development of high-temperature desulfurization systems is the matching of sorbent properties for the selected process operating conditions, namely, sustainable desulfurization kinetics, high sulfur capacity, and mechanical durability over multiple cycles. Additionally, the sulfur species produced during regeneration of the sorbent must be in a form compatible with sulfur recovery systems, such as sulfuric acid or elemental sulfur processes. The overall objective of this program is to develop regenerable sorbents for hydrogen sulfide removal from coal-derived fuel gases in the temperature range 343-538 C (650-1000 F). Two categories of reactor configurations are being considered: moving-bed reactors and fluidized-bed (bubbling and circulating) reactors. In addition, a cost assessment and

  15. Effects of magnetic fields on improving mass transfer in flue gas desulfurization using a fluidized bed

    Science.gov (United States)

    Zhang, Qi; Gui, Keting; Wang, Xiaobo

    2016-02-01

    The effects of magnetic fields on improving the mass transfer in flue gas desulfurization using a fluidized bed are investigated in the paper. In this research, the magnetically fluidized bed (MFB) is used as the reactor in which ferromagnetic particles are fluidized with simulated flue gas under the influence of an external magnetic field. Lime slurry is continuously sprayed into the reactor. As a consequence, the desulfurization reaction and the slurry drying process take place simultaneously in the MFB. In this paper, the effects of ferromagnetic particles and external magnetic fields on the desulphurization efficiency are studied and compared with that of quartz particles as the fluidized particles. Experimental results show that the ferromagnetic particles not only act as a platform for lime slurry to precipitate on like quartz particles, but also take part in the desulfurization reaction. The results also show that the specific surface area of ferromagnetic particles after reaction is enlarged as the magnetic intensity increases, and the external magnetic field promotes the oxidation of S(IV), improving the mass transfer between sulphur and its sorbent. Hence, the efficiency of desulphurization under the effects of external magnetic fields is higher than that in general fluidized beds.

  16. Experimental determination of bed agglomeration tendencies of some common agricultural residues in fluidized bed combustion and gasification

    Energy Technology Data Exchange (ETDEWEB)

    Natarajan, E.; Rao, A.N. [Anna University, Madras (India). Centre for New and Renewable Sources of Energy; Ohman, M.; Nordin, A. [Umea University (Sweden). Energy Technology Centre; Gabra, M. [Lulea University of Technology (Sweden). Div. of Energy Engineering; Liliedahl, T. [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    1998-12-31

    Ever increasing energy demand and the polluting nature of existing fossil fuel energy sources demonstrate the need for other non-polluting and renewable sources of energy. The agricultural residues available in abundance in many countries can be used for power generation. The fluidized bed technology seems to be suitable for converting a wide range of agricultural residues into energy, due to its inherent advantages of fuel flexibility, low operating temperature and isothermal operating condition. The major ash-related problem encountered in fluidized beds is agglomeration which, in the worst case, may result in total defluidization and unscheduled downtime. The initial agglomeration temperature for some common tropical agricultural residues were experimentally determined by using a newly developed method based on the controlled fluidized bed agglomeration test. The agricultural residues chosen for the study were rice husk, bagasse, cane trash and olive flesh. The results showed that the initial agglomeration temperatures were less than the initial deformation temperature predicted by the ASTM standard ash fusion tests for all fuels considered. The initial agglomeration temperatures of rice husk and bagasse were more than 1000{sup o}C. The agglomeration of cane trash and olive flesh was encountered at relatively low temperatures and their initial agglomeration temperatures in gasification were lower than those in combustion with both bed materials. The use of lime as bed material instead of quartz improved the agglomeration temperature of cane trash and olive flesh in combustion and decreased the same in gasification. The results indicate that rice husk and bagasse can be used in the fluidized bed for energy generation since their agglomeration temperatures are sufficiently high. (author)

  17. Conformal nanocoating of zirconia nanoparticles by atomic layer deposition in a fluidized bed reactor

    Science.gov (United States)

    Hakim, Luis F.; George, Steven M.; Weimer, Alan W.

    2005-07-01

    Primary zirconia nanoparticles were conformally coated with alumina ultrathin films using atomic layer deposition (ALD) in a fluidized bed reactor. Alternating doses of trimethylaluminium and water vapour were performed to deposit Al2O3 nanolayers on the surface of 26 nm zirconia nanoparticles. Transmission Fourier transform infrared spectroscopy was performed ex situ. Bulk Al2O3 vibrational modes were observed for coated particles after 50 and 70 cycles. Coated nanoparticles were also examined with transmission electron microscopy, high-resolution field emission scanning electron microscopy and energy dispersive spectroscopy. Analysis revealed highly conformal and uniform alumina nanofilms throughout the surface of zirconia nanoparticles. The particle size distribution and surface area of the nanoparticles are not affected by the coating process. Primary nanoparticles are coated individually despite their high aggregation tendency during fluidization. The dynamic aggregation behaviour of zirconia nanoparticles in the fluidized bed plays a key role in the individual coating of nanoparticles.

  18. Quantitative measurement of segregation phenomena in a binary-mixture fluidized bed by neutron radiography

    Science.gov (United States)

    Umekawa, Hisashi; Furui, Shuji; Oshima, Yoshihiro; Okura, Masashi; Ozawa, Mamoru; Takenaka, Nobuyuki

    2005-04-01

    Owing to a wide variety in fluidization properties of particles, segregation phenomena are hardly avoided in industrial fluidized-bed facilities. For the stability and controllability in the operation of such fluidized-beds, understanding of the relevant mechanism of particulate segregation is indispensable. Many factors, such as the difference in particle size, density, shape, and also arrangement of distributors, can be pointed out as the dominant causes for the segregation. Thus, any marking of particles for quantitative measurement may severely influence the segregation characteristic to be measured. But neutron radiography can be used for the quantitative measurement without disturbing the segregation characteristic. For estimating the segregation phenomena, evaluations of the particle fraction and the void fraction are required. For this purpose, two types of radiographies, i.e., X-ray and neutron radiographies were used in this investigation. Experimental results demonstrated the high performance of this method in investigating of segregation phenomena.

  19. Contribution of hydrodynamic characteristics on the performance of an aerobic biofilm conical fluidized bed.

    Science.gov (United States)

    Zhou, D; Bi, X T; Dong, S

    2011-01-01

    The performance of a conical fluidized bed (TFB) bioreactor, including the biofilm thickness, microbial space density, microbial cell matrix and its efficiency for COD degradation at a bed expansion ratio of 14 to 90%, was studied and compared with a cylindrical fluidized bed (CFB) bioreactor. The hydrodynamic characteristics of the TFB, especially the internal-circulation of bioparticles associated with its unique tapered geometry of the bed, created a much more uniform axial distribution of the bioparticles, leading to the formation of thinner and more compacted biofilms in the TFB compared to that in the CFB. The thinner biofilm in the TFB tended to be stable and possessed more than 6 times of microbial population density compared to the CFB. As a result, thinner biofilms in the TFB contributed to a higher COD removal efficiency, which remained at over 95% at operated expansion ratios, about 15 to 25% higher than that in the CFB. PMID:21436551

  20. Measurements of microwave transmission characteristics through various configurations of fluidized bed materials

    Science.gov (United States)

    1980-05-01

    The feasibility of developing a microwave diagnostic system for measurement of bubbles in a fluidized bed combustion system was experimentally investigated. Experiments were performed in a simple waveguide geometry using microwave frequencies from 2.4 to 3.9 GHz. Styrofoam spacers were used to simulate bubbles in bed materials, such as Greer limestone. The results show that it is feasible to develop a diagnostic system based on microwave transmission through a system consisting of gaps in a limestone media, such as a fluidized bed. The gap is shown to perturb the transmitted power, and to be very sensitive to bubble and bed material dimensions. Resonance effects are shown to occur when dimensions are integer multiples of a quarter wavelength.

  1. 3-D capacitance density imaging of fluidized bed

    Science.gov (United States)

    Fasching, George E.

    1990-01-01

    A three-dimensional capacitance density imaging of a gasified bed or the like in a containment vessel is achieved using a plurality of electrodes provided circumferentially about the bed in levels and along the bed in channels. The electrodes are individually and selectively excited electrically at each level to produce a plurality of current flux field patterns generated in the bed at each level. The current flux field patterns are suitably sensed and a density pattern of the bed at each level determined. By combining the determined density patterns at each level, a three-dimensional density image of the bed is achieved.

  2. Numerical simulation of non-conventional liquid fuels feeding in a bubbling fluidized bed combustor

    Directory of Open Access Journals (Sweden)

    Mladenović Milica R.

    2013-01-01

    Full Text Available The paper deals with the development of mathematical models for detailed simulation of lateral jet penetration into the fluidized bed (FB, primarily from the aspect of feeding of gaseous and liquid fuels into FB furnaces. For that purpose a series of comparisons has been performed between the results of in-house developed procedure- fluid-porous medium numerical simulation of gaseous jet penetration into the fluidized bed, Fluent’s two-fluid Euler-Euler FB simulation model, and experimental results (from the literature of gaseous jet penetration into the 2D FB. The calculation results, using both models, and experimental data are in good agreement. The developed simulation procedures of jet penetration into the FB are applied to the analysis of the effects, which are registered during the experiments on a fluidized pilot furnace with feeding of liquid waste fuels into the bed, and brief description of the experiments is also presented in the paper. Registered effect suggests that the water in the fuel improved mixing of fuel and oxidizer in the FB furnace, by increasing jet penetration into the FB due to sudden evaporation of water at the entry into the furnace. In order to clarify this effect, numerical simulations of jet penetration into the FB with three-phase systems: gas (fuel, oxidizer, and water vapour, bed particles and water, have been carried out. [Projekat Ministarstva nauke Republike Srbije, br. TR33042: Improvement of the industrial fluidized bed facility, in scope of technology for energy efficient and environmentally feasible combustion of various waste materials in the fluidized bed

  3. Use of a seeder reactor to manage crystal growth in the fluidized bed reactor for phosphorus recovery.

    Science.gov (United States)

    Shimamura, Kazuaki; Ishikawa, Hideyuki; Tanaka, Toshihiro; Hirasawa, Izumi

    2007-04-01

    The authors have been engaged in the development of a phosphorus recovery system capable of maintaining high recovery efficiencies, with the chemical cost suppressed. This time, they conducted demonstration tests of a fluidized bed magnesium ammonium phosphate reactor provided with a seeder reactor for the supernatant from anaerobic digestion using a pilot experimental plant with a wastewater treatment capacity of 20 m3/d. For the digestion supernatant with a phosphorus concentration of approximately 300 mg/L, the treated water phosphorus concentration was 10 to 25 mg/L, and the phosphorus recovery efficiency was more than 90%. Relative to the chemical cost in the case of magnesium chloride, the chemical cost in the case of magnesium hydroxide is approximately 40%. Thus, with the new system, it was possible to reduce the running cost while maintaining high recovery efficiencies. PMID:17489275

  4. Vinasses treatment in anaerobic fludized bed reactor.

    Directory of Open Access Journals (Sweden)

    Francisco J. C. Terán

    2009-03-01

    Full Text Available The agricultural use of vinasse produced by the sugar industry has gone through many changes over the years. Coupled with concern over the increased agronomic efficiency and optimizing the management of the use of such waste, you can highlight the major global ecological awareness, developed after 90s. This study aims at the construction and operation of a reactor anaerobic cracker (RALF on pilot scale to verify the burden of chemical demand of oxygen (DQO of vinasse, under mesophilic. The stillage used for feeding the reactor was from a sugar cane processing plant, located in the city of Regente Feijó, São Paulo State. The inoculum was anaerobic sludge from a reactor and upward flow anaerobic sludge blanket (UASB treating wastewater from a factory of soda. The concentrations of vinasse to be treated ranged 17,239 mg DQO L-1 up to 28,174 mg DQO L-1. The effluent pH was maintained between 6.4 and 8.6 during the research. The productivity of biogas in the reactor has not achieved the expected rates, reaching only 46 mL day-1. Maximum efficiency attained during operation was 51.1 %, corresponding to a 14-day operation time, vinasses organic loading of 19.5 kg DQO m-3 dia-1 and to an hydraulic detention time of one day.

  5. Chaotic Study in a Large Jetting Fluidized Bed with a Vertical Nozzle

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    @@1 INTRODUCTION Jetting fluidized beds have been widely applied in such processes as catalytic and flame reactions, combustion and gasification of coal, treatment of waste, cleaning of dusty gases, coating and granulation[1-3]. The flow characteristics of jetting fiuidized beds are relevant to the stable gas jet and the high rates of heat transfer and mass transfer, and the fast chemical reaction pro cess near the gas distributor.

  6. Reaction engineering simulations of oxidative coupling of methane in a circulating fluidized-bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Pannek, U.; Mleczko, L. [Bochum Univ. (Germany). Lehrstuhl fuer Technische Chemie

    1998-10-01

    Oxidative coupling of methane in a circulating fluidized-bed reactor was investigated by means of reaction engineering modeling and simulations. A model of the reactor that combines comprehensive kinetics of the OCM and a model for the description of the bed hydrodynamics was developed and applied to predict the reactor performance. The important goal of the simulations was a better understanding of the effect of the hydrodynamic conditions in the riser reactor on the reaction pathway and the product distribution. (orig.)

  7. Fluidized bed electrodes with high carbon loading for water desalination by capacitive deionization

    NARCIS (Netherlands)

    Doornbusch, G.J.; Dykstra, J.E.; Biesheuvel, P.M.; Suss, M.E.

    2016-01-01

    The use of carbon flow electrodes has significantly impacted electrochemical energy storage and capacitive deionization (CDI), but device performance is limited as these electrodes cannot surpass ∼20 wt% carbon while maintaining flowability. We here introduce flowable fluidized bed electrodes whi

  8. A small scale regularly packed circulating fluidized bed. Part I: Hydrodynamics.

    NARCIS (Netherlands)

    Ham, van der A.G.J.; Prins, W.; Swaaij, van W.P.M.

    1994-01-01

    The present investigation is based on the idea of intensifying the gas¿solids contact in a circulating fluidized bed by introducing obstacles into it. Such obstacles may effectively suppress radial inhomogeneities in the solids flux and concentration, increase the dynamic solids hold-up, and break u

  9. The influence of particle residence time distribution on the reactivity in fluidized bed reactors

    NARCIS (Netherlands)

    Heesink, A.B.M.; Klaus, J.; Swaaij, van W.P.M.

    1994-01-01

    The influence of particle residence time distribution on the average conversion rate (or reactivity) of particles undergoing a non-catalytic gas-solid reaction inside a continuously operated fluidized bed reactor is evaluated. A so called ß-factor is defined as the ratio of the actual reactivity in

  10. Alternating electric field fluidized bed disinfection performance with different types of granular activated carbon

    NARCIS (Netherlands)

    Racyte, J.; Yntema, D.R.; Kazlauskaite, L.; DuBois, A.; Bruning, H.; Rijnaarts, H.H.M.

    2014-01-01

    The removal of pathogens from effluents is important to promote the reuse of these water resources and safeguarding human health, especially in water scarce areas worldwide. Previously a proof-of-principle of a method for water disinfection consisting of fluidized bed electrodes (FBE) with RX3 EXTRA

  11. Fast Pyrolysis of Biomass in a Fluidized Bed Reactor: In Situ Filtering of the Vapors

    NARCIS (Netherlands)

    Hoekstra, Elly; Hogendoorn, Kees J.A.; Wang, Xiaoquan; Westerhof, Roel J.M.; Kersten, Sascha R.A.; Swaaij, van Wim P.M.; Groeneveld, Michiel J.

    2009-01-01

    A system to remove in situ char/ash from hot pyrolysis vapors has been developed and tested at the University of Twente. The system consists of a continuous fluidized bed reactor (0.7 kg/h) with immersed filters (wire mesh, pore size 5 μm) for extracting pyrolysis vapors. Integration of the filter s

  12. Development program on pressurized fluidized-bed combustion. Annual report, July 1, 1974--June 30, 1975

    Energy Technology Data Exchange (ETDEWEB)

    Vogel, G.J.; Cunningham, P.; Fischer, J.

    1975-07-01

    The feasibility of using fluidized-bed combustors in power and steam plants is being evaluated. The concept involves burning fuels such as coal in a fluidized bed of either a naturally occurring, calcium-containing limestone or dolomite or in a synthetically prepared calcium-containing stone. The calcium oxide in the stone reacts with the sulfur released during combustion to form calcium sulfate, which remains in the bed, thus decreasing the level of SO/sub 2/ in the flue gas. Levels of NO/sub x/ in the flue gas are also low. The effect of operating variables and type of stone on the levels of SO/sub 2/ and NO/sub x/ is being determined. Behavior of trace elements during combustion has been preliminarily evaluated. The properties of a fluidized bed at minimum fluidization at different temperatures and pressures have been determined. The CaSO/sub 4/ produced in the combustion process is regenerated to CaO for reuse in the combustor by reductive decomposition at 1095/sup 0/C (2000/sup 0/F). The effects of operating variables on sulfur release during regeneration are being evaluated. Another regeneration process, solid-solid reaction of CaSO/sub 4/ with CaS, is also being investigated. Fundamental investigations of the kinetics of sulfation and regeneration reactions for the natural and synthetic stones are continuing. A model for the sulfation reaction is presented. The status of the new combustor andancillary regenerator equipment is discussed. (auth)

  13. Improved Robust Adaptive Control of a Fluidized Bed Combustor for Sewage Sludge

    Institute of Scientific and Technical Information of China (English)

    MENGHong-Xia; JIAYing-Min

    2005-01-01

    This paper presents a robust model reference adaptive control scheme to deal with uncertain time delay in the dynamical model of a fluidized bed combustor for sewage sludge. The theoretical analysis and simulation results show that the proposed scheme can guarantee not only stability and robustness, but also the adaptive decoupling performance of the system.

  14. The Hydrodynamic Stability of a Fluid-Particle Flow: Instabilities in Gas-Fluidized Beds

    Science.gov (United States)

    Liu, Xue; Howley, Maureen A.; Johri, Jayati; Glasser, Benjamin J.

    2008-01-01

    A simplified model of an industrially relevant fluid-particle flow system is analyzed using linear stability theory. Instabilities of the uniform state of a fluidized bed are investigated in response to small flow perturbations. Students are expected to perform each step of the computational analysis, and physical insight into key mechanistic…

  15. Electric-field enhanced fluidized beds : a low-energy bubble control method

    NARCIS (Netherlands)

    Kleijn van Willigen, F.

    2006-01-01

    Reducing the size of gas bubbles can significantly improve the performance of gas-solid fluidized beds one of the most common reactor types in the chemical industry applied for such diverse systems as gasoline and plastics production to foods processing. However, a control of bubbles in these reac

  16. Industrial Scale Synthesis of Carbon Nanotubes Via Fluidized Bed Chemical Vapor Deposition: A Senior Design Project

    Science.gov (United States)

    Smith, York R.; Fuchs, Alan; Meyyappan, M.

    2010-01-01

    Senior year chemical engineering students designed a process to produce 10 000 tonnes per annum of single wall carbon nanotubes (SWNT) and also conducted bench-top experiments to synthesize SWNTs via fluidized bed chemical vapor deposition techniques. This was an excellent pedagogical experience because it related to the type of real world design…

  17. FLUIDIZED BED STEAM REFORMING FOR TREATMENT AND IMMOBILIZATION OF LOW-ACTIVITY WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HEWITT WM

    2011-04-08

    This report is one of four reports written to provide background information regarding immobilization technologies remaining under consideration for supplemental immobilization of Hanford's low-activity waste. This paper provides the reader a general understanding of fluidized bed steam reforming and its possible application to treat and immobilize Hanford low-activity waste.

  18. Conceptual design of a fluidized bed nuclear reactor: statics, dynamics and safety-related aspects

    NARCIS (Netherlands)

    Agung, A.

    2007-01-01

    In this thesis a conceptual design of an innovative high temperature reactor based on the fluidization principle (FLUBER) is proposed. The reactor should satisfy the following requirements: (a) modular and low power, (b)) large shutdown margin, (c) able to produce power when the bed of particles exp

  19. Effect of Temperature in Fluidized Bed Fast Pyrolysis of Biomass: Oil Quality Assessment in Test Units

    NARCIS (Netherlands)

    Westerhof, R.J.M.; Brilman, D.W.F.; Swaaij, van W.P.M.; Kersten, S.R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  20. Laser Doppler anemometry measurements in a circulating fluidized bed of metal particles

    DEFF Research Database (Denmark)

    Ibsen, Claus Hübbe; Solberg, Tron; Hjertager, Bjørn Helge;

    2002-01-01

    Laser Doppler Anemometry (LDA) measurements were performed in a 1/9 scale model of a 12 MW circulating fluidized bed (CFB) boiler. The model was operated according to scaling laws. The 2D-LDA system used was positioned in two different ways to obtain the three velocity components u, v and w...

  1. Fluidized Bed Steam Reforming For Treatment And Immobilization Of Low-Activity Waste

    International Nuclear Information System (INIS)

    This report is one of four reports written to provide background information regarding immobilization technologies remaining under consideration for supplemental immobilization of Hanford's low-activity waste. This paper provides the reader a general understanding of fluidized bed steam reforming and its possible application to treat and immobilize Hanford low-activity waste.

  2. Fluidized-bed technology for the production of iron products for steelmaking

    Energy Technology Data Exchange (ETDEWEB)

    Plaul, E.J.; Bohm, C.; Schenk, J.L. [Siemens VAI Met Technol GmbH & Co, Linz (Austria)

    2009-02-15

    The family of ironmaking technologies includes three process routes: blast furnace, smelting reduction and direct reduction. Driven by steadily increasing costs of raw materials in the last two decades, the sector has seen a number of new developments in ironmaking technologies, developments based on fluidized-bed technology. The main advantage of a fluidized-bed technology is that fine iron ore can be directly charged to the process without prior treatment; it does away with agglomeration and its concomitant cost, a step practised in blast-furnace, COREX{sup R} and MIDREX{sup R} processes. With Posco of South Korea, Siemens VAI Metals Technologies has successfully developed the FINEX{sup R} process, a smelting reduction based on the direct use of iron ore fines to produce hot metal. The key technology is the four-stage, bubbling fluidized-bed-reactor system, in which fine iron ore is reduced to DRI fines in a countercurrent flow with a reducing gas generated by coal gasification. Beside surveying the current state of the art, this paper discusses the technological principles of smelting-reduction and direct-reduction processes. The status of FINEX{sup R} and the outlook for further developments are described. Crucial to the successful development of the new ironmaking technologies for the direct use of fine ore was the scaling up of the fluidized-bed reactor system, which demonstrated new design features.

  3. Membrane assisted fluidized bed reactor: experimental demonstration for partial oxidation of methanol

    NARCIS (Netherlands)

    Deshmukh, Salim Abdul Rashid Khan

    2004-01-01

    In this thesis the reactor concept has been developed on the basis of an experimental study on the effect of fluidization conditions on the membrane permeation rate in a MAFBR, the extent of gas back mixing and the tube-to-bed heat transfer rates in the presence of membrane bundles with and without

  4. Bed agglomeration in fluidized combustor fueled by wood and rice straw blends

    DEFF Research Database (Denmark)

    Thy, Peter; Jenkins, Brian; Williams, R.B.;

    2010-01-01

    Abstract Petrographic techniques have been used to examine bed materials from fluidized bed combustion experiments that utilized wood and rice straw fuel blends. The experiments were conducted using a laboratory-scale combustor with mullite sand beds, firing temperatures of 840 to 1030 °C, and run...... durations of 5.5 h. A narrow continuous zone borders virtually all bed particles. The highest concentrations of potassium are found in this surface zone that also is enriched in appreciable amounts of other elements. Thin discontinuous films of adhesive cement, formed preferentially on surfaces and contact...... areas between bed particles, ultimately led to bed agglomeration. The interfaces and the presence of gas bubbles in the cement suggest a bonding material with a high surface tension and a liquid state. The cement films originate by filling of irregularities on individual and partially agglomerated bed...

  5. Comparison of the effect of grounding the column wall in gas-solid fluidized beds on electrostatic charge generation

    Energy Technology Data Exchange (ETDEWEB)

    Sowinski, Andrew; Mayne, Antonio; Javed, Bassam; Mehrani, Poupak, E-mail: poupak.mehrani@uottawa.ca [University of Ottawa, Chemical and Biological Engineering Department, 161 Louis Pasteur St., Ottawa, Ontario, K1N 6N5 (Canada)

    2011-06-23

    In gas-solid fluidized beds as particles are fluidized, they continuously come into contact with other particles, as well as the fluidization column wall. This generates electrostatic charges by means of triboelectrification and frictional charging, leading to particle agglomeration, reactor wall fouling, and eventually process downtime and large financial losses. Grounding the fluidization column has been considered as a means of helping electrostatic charge dissipation within fluidized beds; however, in industrial applications despite the process vessels being grounded, the electrostatic problem still persists. This work focused on the effect of fluidization column grounding on particle wall fouling. Experiments were conducted in an atmospheric system consist of a 0.1 m in diameter carbon steel fluidization column. The mass and charge-to-mass ratio (q/m) of the particles that remained adhered to the column wall upon the completion of one hour fluidization period were measured in an electrically isolated and grounded columns to quantitatively determine the amount of reactor wall fouling. Polyethylene particles with different particle size ranges (300- 1000 {mu}m) were fluidized with extra dry air at 1.5 times their respective minimum fluidization velocity (u{sub mf}). Results obtained in the grounded fluidization column were not significantly different from those in the isolated column for all particle size ranges tested where the particles mass collected and q/m and were found to be generally similar.

  6. Pyrolysis kinetics of biomass (herb residue) under isothermal condition in a micro fluidized bed

    International Nuclear Information System (INIS)

    Highlights: • Herb residual pyrolysis kinetics was studied under isothermal condition. • A micro fluidized bed was used as the reactor. • Pyrolysis reaction in the fluidized bed can be finished in around 10 s. • The values of activation energy for generating H2, CO, CO2 and CH4 were achieved. - Abstract: Herb residue is one of the most important industrial biomass in China in terms of availability and potential for use as a bioenergy resource. The kinetics of the thermal decomposition of this fuel in an inert atmosphere was evaluated using a micro fluidized bed. The isothermal differential analysis was applied for determination of kinetic parameters for the major gas components formation including reaction order, activation energy and pre-exponential factor. The temperature inside the micro fluidized bed was steady and the pyrolysis reaction of herb residue finished in around 10 s at 600–800 °C. The reaction time for complete releasing of individual gas components was shorter at higher temperature. Experimental results showed that under the conditions studied, the values of activation energy for generating H2, CO, CO2 and CH4 were 18.90, 12.05, 10.48 and 11.31 kJ/mol respectively, corresponding to the values of pre-exponential factor in the range of 0.88–1.38 s−1. The results indicated that H2 was the most difficult to form due to the highest activation energy, while generating CO was the easiest corresponding to the lowest activation energy. Compared with TGA and other analysis approaches, the kinetic parameters obtain by the micro fluidized bed were significantly lower benefiting from its quick reaction features

  7. Flow cytometric viability assessment of lactic acid bacteria starter cultures produced by fluidized bed drying.

    Science.gov (United States)

    Bensch, Gerald; Rüger, Marc; Wassermann, Magdalena; Weinholz, Susann; Reichl, Udo; Cordes, Christiana

    2014-06-01

    For starter culture production, fluidized bed drying is an efficient and cost-effective alternative to the most frequently used freeze drying method. However, fluidized bed drying also poses damaging or lethal stress to bacteria. Therefore, investigation of impact of process variables and conditions on viability of starter cultures produced by fluidized bed drying is of major interest. Viability of bacteria is most frequently assessed by plate counting. While reproductive growth of cells can be characterized by the number of colony-forming units, it cannot provide the number of viable-but-nonculturable cells. However, in starter cultures, these cells still contribute to the fermentation during food production. In this study, flow cytometry was applied to assess viability of Lactobacillus plantarum starter cultures by membrane integrity analysis using SYBR®Green I and propidium iodide staining. The enumeration method established allowed for rapid, precise and sensitive determination of viable cell concentration, and was used to investigate effects of fluidized bed drying and storage on viability of L. plantarum. Drying caused substantial membrane damage on cells, most likely due to dehydration and oxidative stress. Nevertheless, high bacterial survival rates were obtained, and granulates contained in the average 2.7 × 10(9) viable cells/g. Furthermore, increased temperatures reduced viability of bacteria during storage. Differences in results of flow cytometry and plate counting suggested an occurrence of viable-but-nonculturable cells during storage. Overall, flow cytometric viability assessment is highly feasible for rapid routine in-process control in production of L. plantarum starter cultures, produced by fluidized bed drying.

  8. Biological reduction of nitrates in wastewaters from nuclear processing using a fluidized-bed bioreactor

    International Nuclear Information System (INIS)

    There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt.% NO3- and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in wastewater to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of treating wastewaters containing nitrates. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 gN(NO3-)/m3 by the use of a fluidized-bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor the bacteria are allowed to attach to 0.25- to 0.50-mm-diam coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3. This paper describes the results of a biodenitrification R and D program based on the use of fluidized bioreactors capable of operating at nitrate levels up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(NO3-) per day per liter of empty bioreactor volume. 4 figures, 7 tables

  9. Study of the heat transfer mechanism from a submerged pulse combustor to a fluidized bed

    Science.gov (United States)

    Jeong, Hae-Won

    The objective of this study was to develop a better understanding of the heat transfer mechanism from the oscillating flow in a pulse combustor tail pipe to a fluidized bed. Heat transfer in the pipe and to the bed was studied both theoretically and experimentally. A quasi-steady theory was used to predict the internal heat transfer coefficients in pulsating flow. A packet renewal theory was used to predict the external heat transfer coefficients. A pipe fitted with an electrical heater and four acoustic drivers, which can be submerged in a fluidized bed, simulated the tail pipe of a pulse combustor. Local internal heat transfer rates in the pipe were measured using an enthalpy difference method. Local flow velocities were measured using a hot-film probe and radial temperatures by a thermocouple. The results of this study have shown that a resonant acoustic field increases the local heat transfer rates at the acoustic velocity anti-node and decreases those at the node. These enhancements seem to be caused by a steeper radial temperature gradient near the wall. The overall heat transfer rate is enhanced, when the ratio of acoustic to mean velocity is greater than 1, i.e., when flow reversal occurs. The degree of heat transfer rate enhancement increases as the resonant frequency increases, but decreases as Reynolds number increases. In very turbulent flow pulsations provide no enhancement. A quasi-steady model was developed, which accurately predicts the heat transfer coefficients, for the tail pipe in natural convection (outside fluidized bed) especially when the ratio of acoustic to mean velocity is greater than 3. However, the model somewhat under predicts the heat transfer coefficients for the tail pipe in forced convection (inside fluidized bed). Pulsations inside a submerged tail pipe cause relatively small increase of fluidized bed temperature for low Reynolds number flow, and do not affect the bed temperature measurably for high Reynolds numbers. The rate

  10. Ash problem at wood fired fluidized bed plants; Askproblem vid skogsbraensleeldning i fluidbaedd

    Energy Technology Data Exchange (ETDEWEB)

    Hansson, Soeren; Nystroem, Olle; Axby, Fredrik [Sycon Energikonsult AB, Malmoe (Sweden); Andersson, Christer; Kling, Aasa [Vattenfall Utveckling AB, Aelvkarleby (Sweden)

    2001-03-01

    Several ash related problems occurs during conversion from fossil fuels to bio fuels. The most frequent and expensive problem is agglomeration of bed material (in fluidized beds) and fouling on superheating surfaces. The last problem leads to corrosion problem and decreased transfer of heat. This project is the first part of a proposed project focussed on fluidized bed combustion (FB), because FB have become the dominating technology for combustion of biofuels. The project includes this first update of what has been done by different research institutes since 1997 and results of questionnaire on operating problems to owners of fluidized bed plants. A couple of pilot studies and different thermodynamical studies of bed agglomeration with biofuel combustion have been done during the latest years. There are no published reports where the results from agglomeration tests in pilot scale are verified in full scale plants. No project was found which deals with the fouling problem in the cyclone in a circulating fluidized bed. The knowledge of the mechanisms of deposits growth on heat surfaces is incomplete and more research has to be done of what can prevent the deposit growth. Experience from full scale plants shows that the deposits on heat surfaces grows during a period and after that it falls of the heating surface. There is little knowledge of which ash and flue gas conditions that affects these conditions for bio fuel. The operational experience with wood fuels in circulating fluidized beds is that the main problem with bed material is in the inlet and outlet of the cyclone. A total desulfonated of the bed occurs only when there has been other disturbances or because of operator mistakes. There are a number of things which seem to influence on the deposit problems: (1) Boilers with long residence time have less problem than boilers with short residence time. (2) Fuel size. No plant owner have continuos analysis of the fuel size, but combustion with problem have a

  11. BUBBLE CHARACTERISTICS IN A TWO-DIMENSIONAL VERTICALLY VIBRO-FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    Tao Zhou; Hiroyuki Kage; Hongzhong Li

    2005-01-01

    Measurement of bubble size and local average bubble rise velocity was carried out in a vertically sinusoidal vibro-fluidized bed. Glass beads of Geldart group B particles were fluidized at different gas velocities, while the bed was vibrated at different frequencies and amplitudes to study their effects on the bubble behavior. This is compared with the case of no vibration in a two-dimensional bed and it is concluded that with vibration the local average bubble size,dbav, decreases significantly, especially at minimum bubbling velocity. The average bubble size increases slightly with increasing vibration frequency and amplitude. The local average bubble rise velocity is higher than that with no vibration,though with increasing vibration frequency and amplitude, it does not change significantly.

  12. A phenomenological energy model of biomass pyrolysis under autothermal fluidized bed conditions

    Energy Technology Data Exchange (ETDEWEB)

    Suarez, J.; Beaton, P. [University of the Orient, Santiago de Cuba (Cuba). Faculty of Mechanical Engineering; Zanzi, R. [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    2006-06-15

    In Cuba a variety of types of biomass is being investigated for energy conversion through thermochemical processes into solid, liquid, and gas products. A continuous bench fluidized bed pyrolysis has been designed and is currently under testing. In this article, a transport model has been developed to simulate the axial temperature fields in a bench. The model and experimental results indicated that (1) two zones exist inside of the fluidization column, the dense bed where the exothermic and endothermic reactions are active, and the freeboard zone where the temperature of the pyrolysis product decreases continuously; (2) the bed temperature increases with an increase in the air factor. The predicted temperature is in quantitative agreement with experimental measurements. (Author)

  13. Study on mixing and segregation behaviors in particulate fluidized bed system for mineral processing

    Institute of Scientific and Technical Information of China (English)

    Sahu S.N.; Sahu A.K.; Biswal S.K

    2015-01-01

    In order to identify the mixing and segregation behaviors in a mineral processing operation, present study aimed on the hydrodynamics of solid–liquid fluidization. The study was carried out in a fluidization column with tapings at different height of the bed to collect the sample. The binary particles considered in this study are hematite (4800 kg/m3) and quartz (2600 kg/m3) at different size fractions in the range of average size 87 ? 10?6 m to 400 ? 10?6 m. It is observed that for various binary mixtures, both quartz and hematite particles share the equal composition by mass (50%) at a particular height of fluidized bed, referred as ‘locus point’ of mixing. Study indicates that the mixing zone volume will increase for a continuous fluidized bed plant operation. It is observed that the number of locus points varies from 1 to 3 signifying their dependency on the size ratios of binary mixture. Whenever, the difference in terminal velocity between quartz and hematite particles approaches to zero, mixing is enhanced. Further, the present study is extended to find the segregation index for the different size ratios of quartz and hematite particles. It is evident that depending on the size ratios, various regions such as complete segregation, partial mixing and complete mixing can be observed.

  14. Purification of monoclonal antibodies from whole hybridoma fermentation broth by fluidized bed adsorption.

    Science.gov (United States)

    Thömmes, J; Halfar, M; Lenz, S; Kula, M R

    1995-02-01

    To achive the coarse purification of a monoclonal antibody from whole hybridoma fermentation broth a fluidized bed cation exchange process was used. The procedure consisted of application of the crude sample and washing of the bed in a fluidized mode and elution in a fixed bed mode. A completely clarified eluate was obtained with purification factors between 4 and 8 and a concentration of the desired product (monoclonal antibody) by a factor of more than 3 was achived. Thus, a combination of the three early steps of the downstream process clarification, concentration and coarse purification was possible. Two different materials were tested: a commercially available agarose-based matrix (Stream-line-SP), and a self-derivatized material based on controlled-pore glass (Bioran). Initial experiments were performed to describe the fluidization of the glass material. Comparison with the agarose material showed several differences, the agarose matrix allowing liquid flow closer to plug flow than the glass material. Increased backmixing in the liquid phase was detected when fluidizing the glass adsorbent compared with the agarose-based matrix. Despite this fact, comparison of the two materials with respect to antibody binding and elution demonstrated a similar performance. (c) 1995 John Wiley & Sons, Inc.

  15. Monitoring granulation rate processes using three PAT tools in a pilot-scale fluidized bed.

    Science.gov (United States)

    Tok, Ai Tee; Goh, Xueping; Ng, Wai Kiong; Tan, Reginald B H

    2008-01-01

    The purpose of this research was to analyze and compare the responses of three Process Analytical Technology (PAT) techniques applied simultaneously to monitor a pilot-scale fluidized bed granulation process. Real-time measurements using focused beam reflectance measurement (Lasentec FBRM) and near-infra red spectroscopy (Bruker NIR) were taken by inserting in-line probes into the fluidized bed. Non-intrusive acoustic emission measurements (Physical Acoustic AE) were performed by attaching piezoelectric sensors on the external wall of the fluidized bed. Powder samples were collected at regular intervals during the granulation process and characterized offline using laser diffraction, scanning electron microscopy, stereo-optical microscopy and loss on drying method. PAT data comprising chord length distribution and chord count (from FBRM), absorption spectra (from NIR) and average signal levels and counts (from AE) were compared with the particle properties measured using offline samples. All three PAT techniques were able to detect the three granulation regimes or rate processes (wetting and nucleation, consolidation and growth, breakage) to varying degrees of sensitivity. Being dependent on optical signals, the sensitivities of the FBRM and NIR techniques were susceptible to fouling on probe windows. The AE technique was sensitive to background fluidizing air flows and external interferences. The sensitivity, strengths and weaknesses of the PAT techniques examined may facilitate the selection of suitable PAT tools for process development and scale-up studies.

  16. Development of fluidized-bed furnace for thermal treatment of ammonium uranyl carbonate

    International Nuclear Information System (INIS)

    At present the ammonium uranyl carbonate (AUC) route is developed at a scale of 10 kg/day of UO2. This UO2 is directly compactible and sinterable to densities of 10.55-10.65 gm/cc. The equipment developed include precipitation tank with filtration and methanol washing and fluidized bed furnaces for thermal treatment of AUC and U3O8. During the design and development of these furnaces many experiments were conducted to study fluidization of AUC powder. In this paper the findings of these studies are presented. (author)

  17. Thermo-hydrodynamic design of fluidized bed combustors estimating metal wastage

    CERN Document Server

    Lyczkowski, Robert W; Bouillard, Jacques X; Folga, Stephen M

    2012-01-01

    Thermo-Hydrodynamic Design of Fluidized Bed Combustors: Estimating Metal Wastage is a unique volume that finds that the most sensitive parameters affecting metal wastage are superficial fluidizing velocity, particle diameter, and particle sphericity.  Gross consistencies between disparate data sources using different techniques were found when the erosion rates are compared on the same basis using the concept of renormalization.  The simplified mechanistic models and correlations, when validated, can be used to renormalize any experimental data so they can be compared on a consistent basis using a master equation.

  18. Fluorination of uranium oxides in an engineering scale of fluidized bed

    International Nuclear Information System (INIS)

    In the R and D program for the reprocessing by fluoride volatility process, batch and semi-continuous fluorination have been studied using uranium oxides with or without nonradioactive fission products. A 3 inch-phi fluidized bed was used in obtaining the engineering fluorination date and also handling techniques for kilogram quantities of fluorine and uranium hexafluoride. Described are the equipment system and their technical experiences, mock-up experiments for the determination of fluidization conditions, fluorination rate and F2 utilization, and developments of in-line gas analyzers such as gas chromatograph and thermal conductivity cell for F2 and/or UF6. (auth.)

  19. CFD-DEM and Experimental Study of Bubbling in a Fluidized Bed

    OpenAIRE

    Khawaja, Hassan Abbas

    2015-01-01

    In this study, phenomenon of bubbling is investigated using CFD-DEM and experiments. A CFD-DEM simulation is setup to model the fluidized beds of different sizes. Geldart D particles of 1.2 mm diameter and 1000 Kg/m3 density are modelled. Study revealed different types of fluidization regimes as stated in the literature. An experimental setup is built to obtain the results for the comparison. Comparison revealed that results obtained from both methodologies; CFD-DEM and experiments are ...

  20. MODELING MOISTURE DIFFUSIVITY AND ENERGY CONSUMPTION OF CANTALOUPE SEEDS IN FIXED AND FLUIDIZED BED CONDITIONS

    Directory of Open Access Journals (Sweden)

    Reza Amiri Chayjan

    2012-12-01

    Full Text Available   Background.The main goal in cantaloupe seed drying is the reduction of its moisture content to a safe level, allowing storage in a long period of time. Fluidized bed dryer is a drying process with better heat and mass transfer and shorter drying time. This method is a gentle and uniform drying procedure. Fluidized bed is suitable for sensitive and high moisture materials. Drying parameters of moisture diffusivity and energy are vitally important in modelling and optimizing of the seed dryer system. Material and methods. This study investigated thin layer characteristics of cantaloupe seeds under fixed, semi fluidized and fluidized bed drying with initial moisture content about 61.99% (d.b.. A laboratory fluid- ized bed dryer was utilized in this research. Air temperature levels of 45, 55, 65 and 75°C were applied in drying experiments. Effective moisture diffusivity (Deff of cantaloupe seeds was computed by Fick’s second law in diffusion. Activation energy and specific energy consumption of cantaloupe seeds under different drying conditions were calculated. Results.Calculated values of Deff for drying experiments were in the range of 2.23·10-10and 8.61·10-10m2/s. Values of Deff increased as the input air temperature increased. Activation energy values were computed be- tween 39.21 and 37.55 kJ/mol for 45°C to 75°C, respectively. Specific energy consumption for cantaloupe seeds was calculated at the boundary of 1.58·105and 6.18·105kJ/kg. Conclusion.Results indicated that applying the fluidized bed condition is more effective for convective drying of cantaloupe seeds. Increasing air velocity tends to decrease in activation energy. Decreasing in drying air temperature in different bed conditions caused increase in the energy value. The aforesaid drying parameters are necessary to optimize the operational condition of fluidized bed dryer and to perfect design of the system.  

  1. A New Fluidized Bed Bioreactor Based on Diversion-Type Microcapsule Suspension for Bioartificial Liver Systems.

    Science.gov (United States)

    Lu, Juan; Zhang, Xiaoqian; Li, Jianzhou; Yu, Liang; Chen, Ermei; Zhu, Danhua; Zhang, Yimin; Li, LanJuan

    2016-01-01

    A fluidized bed bioreactor containing encapsulated hepatocytes may be a valuable alternative to a hollow fiber bioreactor for achieving the improved mass transfer and scale-up potential necessary for clinical use. However, a conventional fluidized bed bioreactor (FBB) operating under high perfusion velocity is incapable of providing the desired performance due to the resulting damage to cell-containing microcapsules and large void volume. In this study, we developed a novel diversion-type microcapsule-suspension fluidized bed bioreactor (DMFBB). The void volume in the bioreactor and stability of alginate/chitosan microcapsules were investigated under different flow rates. Cell viability, synthesis and metabolism functions, and expression of metabolizing enzymes at transcriptional levels in an encapsulated hepatocyte line (C3A cells) were determined. The void volume was significantly less in the novel bioreactor than in the conventional FBB. In addition, the microcapsules were less damaged in the DMFBB during the fluidization process as reflected by the results for microcapsule retention rates, swelling, and breakage. Encapsulated C3A cells exhibited greater viability and CYP1A2 and CYP3A4 activity in the DMFBB than in the FBB, although the increases in albumin and urea synthesis were less prominent. The transcription levels of several CYP450-related genes and an albumin-related gene were dramatically greater in cells in the DMFBB than in those in the FBB. Taken together, our results suggest that the DMFBB is a promising alternative for the design of a bioartificial liver system based on a fluidized bed bioreactor with encapsulated hepatocytes for treating patients with acute hepatic failure or other severe liver diseases.

  2. A New Fluidized Bed Bioreactor Based on Diversion-Type Microcapsule Suspension for Bioartificial Liver Systems.

    Directory of Open Access Journals (Sweden)

    Juan Lu

    Full Text Available A fluidized bed bioreactor containing encapsulated hepatocytes may be a valuable alternative to a hollow fiber bioreactor for achieving the improved mass transfer and scale-up potential necessary for clinical use. However, a conventional fluidized bed bioreactor (FBB operating under high perfusion velocity is incapable of providing the desired performance due to the resulting damage to cell-containing microcapsules and large void volume. In this study, we developed a novel diversion-type microcapsule-suspension fluidized bed bioreactor (DMFBB. The void volume in the bioreactor and stability of alginate/chitosan microcapsules were investigated under different flow rates. Cell viability, synthesis and metabolism functions, and expression of metabolizing enzymes at transcriptional levels in an encapsulated hepatocyte line (C3A cells were determined. The void volume was significantly less in the novel bioreactor than in the conventional FBB. In addition, the microcapsules were less damaged in the DMFBB during the fluidization process as reflected by the results for microcapsule retention rates, swelling, and breakage. Encapsulated C3A cells exhibited greater viability and CYP1A2 and CYP3A4 activity in the DMFBB than in the FBB, although the increases in albumin and urea synthesis were less prominent. The transcription levels of several CYP450-related genes and an albumin-related gene were dramatically greater in cells in the DMFBB than in those in the FBB. Taken together, our results suggest that the DMFBB is a promising alternative for the design of a bioartificial liver system based on a fluidized bed bioreactor with encapsulated hepatocytes for treating patients with acute hepatic failure or other severe liver diseases.

  3. Mathematical Simulation of the Structural Properties of Packed and Fluidized Beds

    Science.gov (United States)

    Fedorov, S. S.; Gubinskii, M. V.; Foris', S. N.

    2016-05-01

    Based on the algorithm of successive filling a given volume with single spheres, a mathematical model of random packing of a limited volume of a bed in the field of body forces has been developed. This model can be applied to electrothermal packed- and fluidized-bed furnaces and will make it possible to investigate the thermal and electrical conductivity of such beds. A check of the adequacy of the model showed its correspondence to the well-known experimental and calculated results, as well as the stability of the solutions obtained with its aid.

  4. Behavior of Alkali Metals and Ash in a Low-Temperature Circulating Fluidized Bed (LTCFB) Gasifier

    DEFF Research Database (Denmark)

    Narayan, Vikas; Jensen, Peter Arendt; Henriksen, Ulrik Birk;

    2016-01-01

    , the low reactor temperature ensures that high-alkali biomass fuels canbe used without risk of bed defluidization. This paper presents the first investigation of the fate of alkali metals and ash in lowtemperaturegasifiers. Measurements on bed material and product gas dust samples were made on a 100 k......A low-temperature circulating fluidized bed system (LTCFB) gasifier allows for pyrolysis and gasification to occurat low temperatures, thereby improving the retention of alkali and other inorganic elements within the system and minimizingthe amount of ash species in the product gas. In addition...

  5. Modelling of N2O Reduction in a Circulating Fluidized Bed Boiler

    DEFF Research Database (Denmark)

    Johnsson, Jan Erik; Åmand, Lars Erik; Dam-Johansen, Kim;

    1996-01-01

    The addition of limestone for sulphur retention in Fluidized Bed Combustion (FBC) has been observed to influence the emission of N2O, and in many cases a lower emission was observed. The catalytic activity of a Danish limestone (Stevns Chalk) for decomposition of N2O in a laboratory fixed bed...... quartz reactor was measured. It was found that calcined Stevns Chalk is a very active catalyst for N2O decomposition in an inert atmosphere compared to bed material, i.e. a mixture of ash and sand. However, in FBC the limestone is exposed to a mixture of gases, including CO, CO2 and SO2, and sulphation...

  6. The Operation of Magnetically Assisted Fluidized Bed in Microgravity and Variable Gravity: Experiment and Theory

    Science.gov (United States)

    Sornchamni, T.; Jovanovic, G.; Atwater, J.; Akse, J.; Wheeler, R.

    Typically, the operation of a conventional fluidized bed relies on the balance of gravitational, buoyancy, and drag forces. In the absence of normal gravity, or under microgravity and variable gravity conditions, the gravitational force must be replaced with an alternative force to restore fluidization. Our work has shown that, given a suitable variable magnetic field design, the resulting magnetic field gradient can create sufficient magnetic force acting upon the ferromagnetic particles to replace or supplement the gravitational force. Therefore, the ferromagnetic granular media can be fluidized in either microgravity or hypogravity. In this paper, we present our experimental and theoretical work leading to a) development of theoretical model based on fundamental principles for the design of the Gradient Magnetically Assisted Fluidized Bed (G-MAFB), and b) practical implementation of the G-MAFB in the filtration and destruction of solid biowaste particles from liquid streams. The G-MAFB system consists of a fluidization column and series of Helmholtz electromagnetic coils, with DC power supply. Each Helmholtz ring is powered and controlled separately. Experiments are performed in both 0g (on board NASA KC- 135) and 1g (laboratory) environments. The experiments in 0g are conducted in a two-dimensional, square cross-section, tapered fluidization column. The tapered shape is introduced to provide additional stability to the fluidization particles. The experiments in 0g prove that the magnetic force has a significant role in keeping the particles from extruding out of the bed. Without the magnetic force, it is impossible to have fluidization in space. Solid waste destruction technologies are needed to support long duration human habitation in space. The current technologies, including supercritical water oxidation (SCWO), microwave powered combustion and fluidized bed incineration, have been applied to the destruction of solid wastes, but none are compatible with

  7. Characterization of hydrodynamics and solids mixing in fluidized beds involving biomass

    Science.gov (United States)

    Fotovat, Farzam

    This thesis focuses on the characterization of hydrodynamics and mixing phenomena in fluidized beds containing mixtures of sand and irregular biomass particles. The first objective of this study is understanding the effect of the large biomass particles on the bubbling characteristics and gas distribution pattern of sand fluidized beds. The second objective is the characterization of mixing/segregation of biomass and sand particles under fluidization conditions. A variety of experimental techniques are employed to study the behavior of two constituting phases of a fluidized bed, i.e., dilute (bubble) and dense (emulsion) phases. Exploring the characteristic fluidization velocities of sand-biomass mixtures unveils that the onset of bubbling in these systems occurs at a higher gas velocity compared to that of the initial fluidization velocity (Uif). The initial bubbling velocity (Uib), the final fluidization velocity ( Uff), and the transition gas velocity from bubbling to turbulent regime (Uc) rise by increasing the fraction of biomass in the mixture. Statistical analysis of the pressure signal at top of the bed reveals that increasing the biomass load hinders the evolution of bubbles at a low gas velocity (Usand leads to an increase in the mean voidage of the bed; however, the voidage of each phase remains unaffected. It is observed that large biomass particles trigger a break-up of the bubbles, which results in boosting bubbling frequency. The fraction of bubbles at the center of the bed increases with the load of biomass. At the wall region, however, it starts to decrease by adding 2% wt. biomass to pure sand and then increases with the further addition of biomass. The Radioactive Particle Tracking (RPT) technique is implemented in the second section of this work to study the motion and distribution of biomass particles at U=0.36 m/s and U=0.64 m/s. In this regard, an active biomass particle is tracked for a long period of time and its instantaneous position is

  8. COLLISION PROCESS DETAILS CONTROL THE HYDRODYNAMICS AND HEAT TRANSFER IN FLUIDIZED BED REACTORS

    Institute of Scientific and Technical Information of China (English)

    Masayuki Horio

    2005-01-01

    In the '90s DEM simulation research was successful in exploring its potential in the simulation of fluidization phenomenaand in its application to the design of fluidized-bed processes. Nevertheless, not much progress has been made regardingthe realistic treatment of collision processes that are critical in determining macroscopic mode of fluidization. All throughthe second half of the '90s, the author investigated/demonstrated the issue by introducing different surface interactionscaused by formation of liquid and/or solid bridges, van der Waals force and the existence of surface roughness. In the firstpart of the presentation these are to be summarized and the tasks remaining are discussed. In the second part, are pre-sented the results from a newly developed force-deformation meter to demonstrate the significance of the surfaceroughness and its elasto-plastic characteristics.

  9. Time series analysis of pressure fluctuation in gas-solid fluidized beds

    Directory of Open Access Journals (Sweden)

    C. Alberto S. Felipe

    2004-09-01

    Full Text Available The purpose of the present work was to study the differentiation of states of typical fluidization (single bubble, multiple bubble and slugging in a gas-solid fluidized bed, using spectral analysis of pressure fluctuation time series. The effects of the method of measuring (differential and absolute pressure fluctuations and the axial position of the probes in the fluidization column on the identification of each of the regimes studied were evaluated. Fast Fourier Transform (FFT was the mathematic tool used to analysing the data of pressure fluctuations, which expresses the behavior of a time series in the frequency domain. Results indicated that the plenum chamber was a place for reliable measurement and that care should be taken in measurement in the dense phase. The method allowed fluid dynamic regimes to be differentiated by their dominant frequency characteristics.

  10. Growth of Saccharomyces cerevisiae in form of solid particles in a gaseous fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Moebus, O.; Teuber, M.; Reuter, H.

    1981-01-01

    The growth of yeast paricles in a pneumatic bioreactor (gaseous fluidized bed) is described. Pressed bakers yeast was grated into small particles suitable for fluidization. The growth medium was sprayed onto the fluidized particles. Growth of yeasts in the new type of bioreactor was proven by: production of yeast biomass (growth yield 45.7 g yeast dry matter per 100 g glucose; technical generation time = 17 h); assimilation of glucose (99%) and nitrogen (100%) from the medium. Production of enough biological heat to effect direct evaporation of the water content of the medium; proof of the Crabtree-effect (production of ethanol at high substrate supply rates); and proof of the viability of the yeast cells in the yeast particles during pneumatic fermentation. The conditions (temperature, humidity and speed of the supporting air flow) for the aerobic fermentation of glucose by Saccharomyces cerevisiae are described.

  11. Modeling of moisture diffusivity, activation energy and energy consumption in fluidized bed drying of rough rice

    Science.gov (United States)

    Khanali, Majid; Banisharif, Alireza; Rafiee, Shahin

    2016-01-01

    The present work was an attempt to assess the effective moisture diffusivity, activation energy, and energy consumption of rough rice in a batch fluidized bed dryer. Drying experiments were conducted at drying air temperatures of 50, 60, and 70 °C, superficial fluidization velocities of 2.3, 2.5, and 2.8 m/s, and solids holdup of 1.32 kg. Drying kinetics showed that the whole fluidized bed drying of rough rice occurred in the falling rate period. The effective moisture diffusivity was described by an Arrhenius equation. The evaluated effective moisture diffusivity increased with drying air temperature and superficial fluidization velocity and was found to vary from 4.78 × 10-11 to 1.364 × 10-10 m2/s with R2 higher than 0.9643. The activation energy and the pre-exponential factor of Arrhenius equation were found to be in the range of 36.59-44.31 kJ/mol and 4.71 × 10-5-7.15 × 10-4 m2/s, respectively. Both maximum values of the specific energy consumption of 74.73 MJ/kg and the total energy need of 12.43 MJ were obtained at 60 °C drying air temperature and 2.8 m/s superficial fluidization velocity. Both minimum values of the specific energy consumption of 29.98 MJ/kg and the total energy need of 4.85 MJ were obtained under drying air temperature of 70 °C and superficial fluidization velocity of 2.3 m/s.

  12. Flow structure of the solids in a three-dimensional liquid fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Kiared, K.; Chaouki, J. [Ecole Polytechnique de Montreal, Quebec (Canada). Dept. of Chemical Engineering; Larachi, F. [Laval Univ., Quebec (Canada); Cassanello, M. [Univ. de Buenos Aires (Argentina). Dept. Industrias FCEyN

    1997-11-01

    The motion of solids in a cylindrical liquid fluidized bed was experimentally characterized by means of a noninvasive radioactive particle tracking technique (RPT) for two monosized bed inventories, spherical glass beads (3 mm GB, density = 2,500 kg/m{sup 3}) and nonspherical poly-(vinyl chloride) particles (5.5 mm PVC, density = 1,300 kg/m{sup 3}). RPT-monitoring of a single radioactive solid tracer mimicking faithfully the characteristics of the solids revealed the detailed solids flow features by determining the tracer instantaneous 3-D Lagrangian trajectory and then its local instantaneous velocities. Transverse solids dispersion coefficients were an order of magnitude lower than their axial counterpart. Time, longitudinal, and circumferential averaging of local velocities in the fully developed region of the fluidized bed revealed a weak gulf streaming characterized by axial velocities positive (respectively negative) in the core and negative (respectively positive) near the vessel walls for the GBs (respectively for the PVCs). The measured mean circumferential ensemble-averaged radial velocity was essentially zero in the fully developed region. The solids flow turbulence field was anisotropic, but the less dense the particles, the closer to isotropy was the solids flow. Computed shear stress profiles showed that PVC particles exhibited a higher shear stress than GB particles. The dynamic solids flow structure inside a 3-D liquid fluidized bed can be viewed as a core-annulus structure with axially-dispersed plug-flow and radial dispersion in each of the upward and downward zones.

  13. Bubble dynamics in a two-dimensional gas-solid fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Related referential studies on gas-solid two-phase flows were briefly reviewed. Bubble ascending in a two-dimensional (2D) gas-solid fluidized bed was studied both experimentally and numerically. A modified continuum model expressed in the conservation form was used in numerical simulation. Solid-phase pressure was modeled via local sound speed; gas-phase turbulence was described by the K-ε two-equation model. The modified implicit multiphase formulation (IMF) scheme was used to solve the model equations in 2D Cartesian/cylindrical coordinates. The bubble ascending velocity and particle motion in the 2D fluidized bed were measured using the photochromic dye activation (PDA) technique, which was based on UV light activation of particles impregnated with the dye. Effects of bed height and superficial gas velocity on bubble formation and ascent were investigated numerically. The numerically obtained bubble ascending velocities were compared with experimental measurements. Gas bubble in jetting gas-solids fluidized bed was also simulated numerically.

  14. An evaluation of factors influencing the energy efficient operation of well-mixed fluidized bed dryers

    Energy Technology Data Exchange (ETDEWEB)

    Baker, C.G.J. [Kuwait Univ., Safat (Kuwait). Dept. of Chemical Engineering

    2005-07-01

    Efforts to reduce the energy consumption of dryers are often hampered by a limited understanding of the influence of design and operating parameters on energy efficiency. The results of a study of energy consumption calculations performed on a well-mixed fluidized bed dryer simulator were presented. The aim of the study was to determine exhaust air temperature-humidity required in a room to yield a specified outlet moisture content. In addition, the predictions of a well-mixed fluidized bed dryer simulator were compared with those of an ideal adiabatic dryer model developed in previous research. The overall objective of the study was to contribute to the development of a strategy for evaluating the effectiveness of various energy conservation options. Six model drying curves were used to examine the effects of drying rates and hygroscopicity. Results indicated that the specific energy was higher for slow-drying hygroscopic solids and lower for fast-drying non-hygroscopic solids. Specific energy consumption increased with decreasing bed temperature and outlet moisture content, but was independent of solids loading and air flow rate. There was good agreement between zero heat loss data and a single theoretical curve which approximated the performance of the ideal adiabatic dryer. In addition, differences between the behaviour of well-mixed and plug flow fluidized bed dryers were observed. It was concluded that the insights provided by this study confirmed the value of the simulator for design and performance calculations. 10 refs., 2 tabs., 8 figs.

  15. CFD-DEM simulation of a conceptual gas-cooled fluidized bed nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, Lucilla C.; Su, Jian, E-mail: lucillalmeida@gmail.com, E-mail: sujian@nuclear.ufrj.br [Coordenacao dos Programas de Pos-Graduacao (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Nuclear; Aguirre, Joao, E-mail: aguirre@rocky-dem.com [Engineering Simulation and Scientific Software (ESSS), Rio de Janeiro, RJ (Brazil)

    2015-07-01

    Several conceptual designs of the fluidized-bed nuclear reactor have been proposed due to its many advantages over conventional nuclear reactors such as PWRs and BWRs. Amongst their characteristics, the enhanced heat transfer and mixing enables a more uniform temperature distribution, reducing the risk of hot-spot and excessive fuel temperature, in addition to resulting in a higher burnup of the fuel. Furthermore, the relationship between the bed height and reactor neutronics turns the coolant flow rate control into a power production mechanism. Moreover, the possibility of removing the fuel by gravity from the movable core in case of a loss-of-cooling accident increases its safety. High-accuracy modeling of particles and coolant flow in fluidized bed reactors is needed to evaluate reliably the thermal-hydraulic efficiency and safety margin. The two-way coupling between solid and fluid can account for high-fidelity solid-solid interaction and reasonable accuracy in fluid calculation and fluid-solid interaction. In the CFD-DEM model, the particles are modeled as a discrete phase, following the DEM approach, whereas the fluid flow is treated as a continuous phase, described by the averaged Navier-Stokes equations on a computational cell scale. In this work, the coupling methodology between Fluent and Rocky is described. The numerical approach was applied to the simulation of a bubbling fluidized bed and the results were compared to experimental data and showed good agreement. (author)

  16. The study of solid circulation rate in a compartmented fluidized bed gasifier (CFBG)

    Science.gov (United States)

    Wee, S. K.; Pok, Y. W.; Law, M. C.; Lee, V. C. C.

    2016-06-01

    Biomass waste has been abundantly available in Malaysia since the booming of palm oil industry. In order to tackle this issue, gasification is seen a promising technology to convert waste into energy. In view of the heat requirement for endothermic gasification reaction as well as the complex design and operation of multiple fluidized beds, compartmented fluidized bed gasifier (CFBG) with the combustor and the gasifier as separate compartments is proposed. As such, solid circulation rate (SCR) is one of the essential parameters for steady gasification and combustion to be realized in their respective compartments. Experimental and numerical studies (CFD) on the effect of static bed height, main bed aeration, riser aeration and v-valve aeration on SCR have been conducted in a cold- flow CFBG model with only river sand as the fluidizing medium. At lower operating range, the numerical simulations under-predict the SCR as compared to that of the experimental results. Also, it predicts slightly different trends over the range. On the other hand, at higher operating range, the numerical simulations are able to capture those trends as observed in the experimental results at the lower operating range. Overall, the numerical results compare reasonably well with that of the experimental works.

  17. DEVELOPMENT OF COAL DRY BENEFICIATION WITH AIR-DENSE MEDIUM FLUIDIZED BED IN CHINA

    Institute of Scientific and Technical Information of China (English)

    Qingru Chen; Lubin Wei

    2005-01-01

    In China more than two-thirds of available coal reserves are in arid areas, where, to beneficiate the run-of-mine coal,there is not enough water resource required by conventional processing. Developing efficient dry beneficiation technology is of great significance for efficient coal utilization in China, notably the clean coal technology (CCT). The dry coal beneficiation technology with air-dense medium fluidized bed utilizes air-solid suspension as beneficiating medium whose density is consistent for beneficiation, similar in principle to the wet dense medium beneficiation using liquid-solid suspension as separating medium. The heavy portion in feedstock whose density is higher than the density of the fluidized bed will sink, whereas the lighter portion will float, thus stratifying the feed materials according to their density.In order to obtain efficient dry separation in air-dense medium fluidized bed, stable fluidization with well dispersed micro-bubbles must be achieved to ensure low viscosity and high fluidity. The pure buoyancy of beneficiation materials plays a main role in fluidized bed, and the displaced distribution effect should be restrained. The displaced distribution effects include viscosity displaced distribution effect and movement displaced distribution effect. The former is caused by viscosity of the fluidized bed. It decreases with increasing air flow velocity. Movement displaced distribution effect will be large when air flow rate is too low or too high. If medium particle size distribution and air flow are well controlled, both displaced distribution effects could be controlled effectively. A beneficiation displaced distribution model may be used to optimize beneficiation of feedstock with a wide particle size distribution and multiple components in the fluidized bed. The rheological characteristics of fluidized beds were studied using the falling sphere method. Experimental results indicated that the fluidized bed behaves as a Bingham fluid

  18. DEVELOPMENT OF COAL DRY BENEFICIATION WITH AIR-DENSE MEDIUM FLUIDIZED BED IN CHINA

    Institute of Scientific and Technical Information of China (English)

    Qingru; Chen; Lubin; Wei

    2005-01-01

    In China more than two-thirds of available coal reserves are in arid areas, where, to beneficiate the run-of-mine coal,there is not enough water resource required by conventional processing. Developing efficient dry beneficiation technology is of great significance for efficient coal utilization in China, notably the clean coal technology (CCT). The dry coal beneficiation technology with air-dense medium fluidized bed utilizes air-solid suspension as beneficiating medium whose density is consistent for beneficiation, similar in principle to the wet dense medium beneficiation using liquid-solid suspension as separating medium. The heavy portion in feedstock whose density is higher than the density of the fluidized bed will sink, whereas the lighter portion will float, thus stratifying the feed materials according to their density.In order to obtain efficient dry separation in air-dense medium fluidized bed, stable fluidization with well dispersed micro-bubbles must be achieved to ensure low viscosity and high fluidity. The pure buoyancy of beneficiation materials plays a main role in fluidized bed, and the displaced distribution effect should be restrained. The displaced distribution effects include viscosity displaced distribution effect and movement displaced distribution effect. The former is caused by viscosity of the fluidized bed. It decreases with increasing air flow velocity. Movement displaced distribution effect will be large when air flow rate is too low or too high. If medium particle size distribution and air flow are well controlled, both displaced distribution effects could be controlled effectively. A beneficiation displaced distribution model may be used to optimize beneficiation of feedstock with a wide particle size distribution and multiple components in the fluidized bed. The rheological characteristics of fluidized beds were studied using the falling sphere method. Experimental results indicated that the fluidized bed behaves as a Bingham fluid

  19. Two-stage dual fluidized bed gasification: Its conception and application to biomass

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Guangwen [Research Laboratory, IHI Corporation, Ltd., Isogo-Ku, Yokohama 235-8501 (Japan); Institute of Process Engineering, Chinese Academy of Sciences, Haidian, Beijing 100080 (China); Murakami, Takahiro [Research Laboratory, IHI Corporation, Ltd., Isogo-Ku, Yokohama 235-8501 (Japan); Clean Gas Group, National Institute of Advanced Science and Technology, Tsukuba, Ibaraki 305-8569 (Japan); Suda, Toshiyuki; Matsuzaw, Yoshiaki; Tani, Hidehisa [Research Laboratory, IHI Corporation, Ltd., Isogo-Ku, Yokohama 235-8501 (Japan)

    2009-01-15

    The quoted two-stage dual fluidized bed gasification (T-DFBG) devises the use of a two-stage fluidized bed (TFB) to replace the single-stage bubbling fluidized bed gasifier involved in the normally encountered dual fluidized bed gasification (N-DFBG) systems. By feeding fuel into the lower stage of the TFB, this lower stage functions as a fuel gasifier similar to that in the N-DFBG so that the upper stage of the TFB works to upgrade the produced gas in the lower stage and meanwhile to suppress the possible elutriation of fuel particles fed into the freeboard of the lower-stage bed. The heat carrier particles (HCPs) circulated from the char combustor enter first the upper stage of the TFB to facilitate the gas upgrading reactions occurring therein, and the particles are in turn forwarded into the lower stage to provide endothermic heat for fuel pyrolysis and gasification reactions. Consequently, with T-DFBG it is hopeful to increase gasification efficiency and decrease tar content in the produced gas. This anticipation was corroborated through gasifying dry coffee grounds in two 5.0kg/h experimental setups configured according to the principles of T-DFBG and N-DFBG, respectively. In comparison with the N-DFBG case, the test according to T-DFBG increased, the fuel C conversion and cold gas efficiency by about 7% and decreased tar content in the produced gas by up to 25% under similar reaction conditions. Test results demonstrated also that all these upgrading effects via adopting T-DFBG were more pronounced when a Ca-based additive was blended into the fuel. (author)

  20. Incineration of contaminated organic solvents in a fluidized-bed calciner

    International Nuclear Information System (INIS)

    The reprocessing of expended reactor fuels at the Idaho Chemical Processing Plant (ICPP) generates contaminated organic solvents. An evaluation of potential management alternatives shows that several are suitable for management of contaminated solvents containing tri-butyl phosphate (TBP): the solvent could be burned in a commercially-available burner which absorbs the phosphorus on a fluidized-bed of limestone leaving a solid product for burial; the solvent could be burned in a small fluidized-bed calciner which solidifies non-radioactive feed by in-bed combustion of the contaminated solvent. The fluidized-bed absorbs the phosphate forming a solid product for burial; the solvents could be solidified with a gel or sorbant for burial if the reprocessing system were modified to reduce the solvent volume; and the contaminated solvent could be burned in an existing fluidized-bed calciner designed for solidifying high-level aqueous wastes. Burning the solvent in the existing calciner was selected for process verification because it provides an existing burner, off-gas system, and solids transfer and storage system. No additional wastes are generated. A set of four pilot-plant tests verified the absence of adverse effects from the phosphorus in the fuel when calcining simulated ICPP aqueous wastes. Essentially all of the phosphorus remained in the calcined solids with only a neglegible quantity remaining in the scrubbed off-gas. Combustion efficiency was high (93 to 96%). There were no observable adverse effects on solids in the scrubbing system, corrosion rates, or solids flowability (for retrieval). Conclusions of general applicability are: alternative technologies are available for disposal of contaminated solvents, and the use of an existing fuel-using facility, e.g., calciner or incinerator - designed for contaminated wastes will usually be cost effective

  1. Woody waste air gasification in fluidized bed with Ca- and Mg-modified bed materials and additives

    International Nuclear Information System (INIS)

    This study focuses on the promotion of biomass gasification for hydrogen production in a fluidized bed reactor with the bed additives zeolite, CaO, and Ca- and Mg-based silica sands. The results show that zeolite has higher capacity for enhancing hydrogen promotion abilities than CaO with the amount was 200 g in tests. Regarding the Ca- and Mg-based silica sands, Ca/SiO2 decreases the CO2 selectivity and Mg/SiO2 enhances the H2 selectivity owing to CO2 adsorption via the formation of CaO and the promotion of the water gas shift reaction, respectively. The optimal concentration of Mg-based bed materials corresponds to a Mg concentration of 0.5 wt.%. The additives play important roles in increasing the reaction rate, enhancing the biomass gasification, and promoting carbon transformation. -- Graphical abstract: The aim of this study is not only in estimation of the influence of the alkaline metals concentrations, but also in preparation of the modified fluidization mediums. A basic stoichiometric analysis of alkaline concentration for hydrogen production during biomass gasification in fluidized bed is also in consideration. Highlights: ► Various bed-additives concentrations on syngas performance are discussed. ► All additives significantly increase rate of hydrogen production in gasification. ► Zeolite has higher capacity for enhancing hydrogen production rate than CaO. ► Ca-based additives promoted the heating value and cold gas efficiency. ► The optimal concentration of Mg-based additive was 0.5 wt.% for hydrogen production

  2. Improving the performance of the Y-12 fluidized bed contactors: Final report on investigations at the University of Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Daw, C.S.; Hawk, J.A. [Oak Ridge National Lab., TN (United States)

    1993-08-01

    Recent tests at The University of Tennessee in Knoxville (UT) have demonstrated improved fluidization performance in a mockup of the Oak Ridge Y-12 Plant fluidized bed with a modified gas distributor. Combining the modified distributor with the recently developed fluidization intensity module is expected to result in substantial operational improvements for the fluidized beds in Building 9212 at Y-12. Important additional benefits coming from the improved operation of the Y-12 fluidized beds will be a reduction in the consumption of reactant gases, a reduction in scrubber waste production, and a reduced need for manual cleaning of the particulate removal system. UT tests have also demonstrated that the tapered wall design traditionally used for the Y-12 fluidized beds does not provide a sufficient improvement in fluidization quality to justify the continued use of this design in place of a more conventional straight-wall configuration. The straight-wall design for replacement beds is expected to result in substantial equipment cost savings. Other operating scenarios that could potentially be used to reduce reactant gas consumption and scrubber waste production have also been considered. These scenarios are documented here for future reference.

  3. Field Driven Charging Dynamics of a Fluidized Granular Bed

    CERN Document Server

    Yoshimatsu, R; Shinbrot, T; Herrmann, H J

    2016-01-01

    A simplified model has previously described the inductive charging of colliding identical grains in the presence of an external electric field. Here we extend that model by including heterogeneous surface charge distributions, grain rotations and electrostatic interactions between grains. We find from this more realistic model that strong heterogeneities in charging can occur in agitated granular beds, and we predict that shielding due to these heterogeneities can dramatically alter the charging rate in such beds.

  4. 气固流化床中的信息传输%INFORMATION TRANSPORT IN GAS-SOLID FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    黄轶伦; 汪乐宇; 张卫东; 郑燕萍; 陈伯川

    2000-01-01

    The pressure fluctuation time series of gas-solid fluidized beds contains abundant information of dynamic characteristics. However, there is no accurate and reliable method to extract the embedded information due to the highly random nature of fluidization. In this work,by adopting the concept of mutual information in Shannon information theory, the authors investigate the dependence between pressure fluctuation time series in the reconstruction phase space at two different locations in the fluidized bed. The curve of mutual information indicates that there exists high-speed information transport in the fluidized bed. The average information transport speed of pressure fluctuation and its changes with gas velocity is detected by experiments. The authors argue that the information is transferred with the disturbing of particles in the beds, and the information transport speed decreases with the increasing of interspace rate.

  5. Combustion of rice husk in a multiple-spouted fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Albina, D.O. [Asian Institute of Technology, Pathumthani (Thailand). Energy Program

    2003-09-01

    The performance of the multiple-spouted fluidized bed was evaluated by investigating the effects of different parameters on combustion efficiency and emission for different methods of feeding. The parameters considered were the different levels of combustion air and the different primary-to-secondary air ratios at each level, while the methods of feeding were under-bed and over-bed feeding. It was found that the method of feeding influenced the combustion efficiency of the multiple-spouted bed. The combustion efficiency appeared to be higher with under-bed feeding as compared to over-bed feeding; and emission of CO was less in the case of under-bed feeding than with over-bed feeding. The changes in excess air levels influenced the combustion efficiency of the spouted bed. It was found that combustion efficiency with over-bed feeding was best at 10% excess air; in general, combustion efficiency with under-bed feeding was favorable at 20% excess air level. (author)

  6. Study of fluidized-bed desulfurization with zinc ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Grindley, T

    1991-01-01

    Previous work established the technical feasibility of desulfurizing the hot product gases of coal gasification with fixed beds of a regenerable zinc ferrite sorbent. This process, intended for integration with coal gasifiers and gas turbines, has been tested and studied in considerable detail in a process development unit. Though possessing the advantages of high-sulfur absorption at low-sulfur breakthrough and the lack of sorbent attrition characteristic of a stationary bed, fixed beds also have inherent disadvantages: susceptibility to plugging by particles and a large diluent requirement during regeneration to control the reaction zone temperature. Therefore, METC conducted a scoping laboratory test program to determine the desulfurizing capability of fluid beds of zinc ferrite. Results from this program are presented. The results generally demonstrated that fluid beds of zinc ferrite have the potential to lower the H{sub 2}S level in hot gas from 10,000 to 10 ppmv. To achieve this at a high-sorbent sulfur loading would require two fluid-bed stages. Sorbent attrition appears to be acceptably low. Planned future activities include tests at high pressure with both simulated gas and in a gasifier sidestream.

  7. CFD simulation of bubbling and collapsing characteristics in a gas-solid fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Pei Pei; Zhang Kai; Lu Erwei; Wen Dongsheng

    2009-01-01

    Computational Fluid Dynamics (CFD) has become an alternative method to experiments for understanding the fluid dynamics of multiphase flow. A two-fluid model, which contains additional terms in both the gas- and solid-phase momentum equations, is used to investigate the fluidization quality in a fluidized bed. A case study for quartz sand with a density of 2,660 kg/m3 and a diameter of 500 μm,whose physical property is similar to a new kind of catalyst for producing clean fuels through the residue fluid catalytic cracking process, is simulated in a two-dimensional fluidized bed with 0.57 m width and 1.00 m height. Transient bubbling and collapsing characteristics are numerically investigated in the platform of CFX 4.4 by integrating user-defined Fortran subroutines. The results show that the fluidization and collapse process is in fair agreement with the classical theory of Geldart B classification, but the collapse time is affected by bubbles at the interface between the dense phase and freeboard.

  8. KARAKTERISTIK FISIKOKIMIA PATI SAGU HASIL PENGERINGAN SECARA FLUIDISASI MENGGUNAKAN ALAT PENGERING CROSS FLOW FLUIDIZED BED BERTENAGA SURYA DAN BIOMASSA

    Directory of Open Access Journals (Sweden)

    Abadi Jading

    2012-04-01

    Full Text Available PHYSICOCHEMICAL CHARACTERISTICS OF SAGO STARCH OBTAINED FROM FLUIDIZED BED DRYING USING SOLAR AND BIOMASS POWERED CROSS FLOW FLUIDIZED BED DRYER. The research aim is to study the comparative quality of sago starch drying results using cross flow fluidized bed dryer powered by solar and biomass in conventional drying, particularly the chemical composition and physicochemical characteristics. This research was conducted through a drying phase of wet sago starch using a cross flow fluidized bed dryer, and drying in conventional as well as dried sago starch quality testing results are drying. The results of this study indicate that dry sago starch which has been drained by means of cross flow fluidized bed dryer has a chemical composition that does not vary much with starch which is dried by conventional drying, so that the dried sago starch produced by the dryer is very good. On the other hand the use of dryers is the more correct because the physicochemical properties of sago starch using a low drying temperature and drying time is short. Tujuan penelitian ini adalah mempelajari perbandingan kualitas pati sagu hasil pengeringan menggunakan alat pengering cross flow fluidized bed bertenaga surya dan biomassa dengan pengeringan secara konvensional, khususnya komposisi kimia dan karakteristik fisikokimia. Penelitian ini dilakukan melalui beberapa tahapan yaitu pengeringan pati sagu basah menggunakan alat pengering cross flow fluidized bed, pengeringan secara konvensional serta pengujian kualitas pati sagu kering hasil pengeringan. Hasil dari penelitian ini menunjukkan bahwa pati sagu kering yang telah dikeringkan dengan alat pengering cross flow fluidized bed memiliki komposisi kimia yang tidak berbeda jauh dengan pati yang dikeringkan dengan cara pengeringan secara konvensional, sehingga pati sagu kering yang dihasilkan oleh alat pengering tersebut sangat baik. Di sisi lain penggunaan alat pengering ini semakin memperbaiki sifat fisikokimia pati

  9. Proceedings of the sixth international conference on fluidized bed combustion. Volume II. Technical sessions

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-08-01

    The Sixth International Conference on Fluidized Bed Combustion was held April 9-11, 1980, at the Atlanta Hilton, Atlanta, Georgia. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the US Environmental Protection Agency, and the Tennessee Valley Authority. The papers covered recent developments in atmospheric and pressurized fluidized-bed combustion, especially the design, operation and control of pilot and demonstration plants. The cleanup of combustion products and the erosion, corrosion and fouling of gas turbines was emphasized also. Fifty-five papers from Volume 2 of the proceedings have been entered individually into EDB and ERA; five papers had been entered previously from other sources. (LTN)

  10. Establishment of an Environmental Control Technology Laboratory with a Circulating Fluidized-Bed Combustion System

    Energy Technology Data Exchange (ETDEWEB)

    Wei-Ping Pan; Yan Cao; Songgeng Li

    2006-04-01

    This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period January 1, 2006 through March 31, 2006. Work was performed on the following activities. First, the fabrication and manufacture of the CFBC Facility were completed. The riser, primary cyclone and secondary cyclone of Circulating Fluidized Bed (CFB) Combustor have been erected. Second, the Mercury Control Workshop and the Grand Opening of Institute for Combustion Science and Environmental Technology (ICSET) were successfully held on February 22 and 23, 2006, respectively. Third, effects of hydrogen chlorine (HCl) and sulfur dioxide (SO{sub 2}) on mercury oxidation were studied in a drop tube reactor. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter is described in this report.

  11. Treatment of TFT-LCD wastewater containing ethanolamine by fluidized-bed Fenton technology.

    Science.gov (United States)

    Anotai, Jin; Chen, Chia-Min; Bellotindos, Luzvisminda M; Lu, Ming-Chun

    2012-06-01

    The objectives of this study are: (1) to determine the effect of pH, initial concentration of Fe(2+) and H(2)O(2) dosage on the removal efficiency of MEA by fluidized-bed Fenton process and Fenton process, (2) to determine the optimal conditions for the degradation of ethanolamine from TFT-LCD wastewater by fluidized-bed Fenton process. In the design of experiment, the Box-Behnken design was used to optimize the operating conditions. A removal efficiency of 98.9% for 5mM MEA was achieved after 2h under optimal conditions of pH3, [Fe(2+)]=5mM and [H(2)O(2)]=60mM.

  12. Microstructure of multicrystalline silicon seeded by polysilicon chips and fluidized bed reactor granules

    Science.gov (United States)

    Ekstrøm, K. E.; Stokkan, G.; Autruffe, A.; Søndenå, R.; Dalaker, H.; Arnberg, L.; Di Sabatino, M.

    2016-05-01

    Multicrystalline silicon displays a considerable smaller average grain size and reduced dislocation generation when being seeded by polycrystalline silicon chips or fluidized bed reactor silicon granules. A simple texture analysis shows how the initially random grain structure of the seeds develops a weak preference for near- and near- oriented grains upwards in the ingot. Closer investigations reveal a considerable coarsening of the initial microstructure of the seeds during the directional solidification process, especially for small fluidized bed reactor granules. The irregular shape of polysilicon chips allows for melt penetration into the seeding structure and potential indentation effects that may account for the increased dislocation generation observed in this case. The increased generation may, however, also be related to a higher ratio of ∑27 grain boundaries.

  13. Combustion Characteristics of Lignite Char in a Laboratory-scale Pressurized Fluidized Bed Combustor

    Science.gov (United States)

    Murakami, Takahiro; Suzuki, Yoshizo

    In a dual fluidized bed gasifier, the residual char after steam gasification is burnt in riser. The objectives of this work are to clarify the effect of parameters (temperature, pressure, and particle size of lignite char) of char combustion using a laboratory-scale pressurized fluidized bed combustor (PFBC). As a result, the burnout time of lignite char can be improved with increasing operating pressure, and temperature. In addition, the decrease in the particle size of char enhanced the effect on burnout time. The initial combustion rate of the char can be increased with increasing operating pressure. The effect was decreased with increasing operating temperature. However, the effect of operating pressure was slightly changed in small particle size, such as 0.5-1.0 mm. It takes about 20 sec to burn 50% of char in the operating pressure of 0.5 MPa and the particle size of 0.5-1.0 mm.

  14. Combustion characteristics and emissions of Seyitomer lignite-olive cake mixture in a fluidized bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Devrim B. Kaymak; Husnu Atakul; Ekrem Ekinci [Istanbul Technical University, Istanbul (Turkey). Department of Chemical Engineering

    2007-07-01

    The low quality Turkish lignites cause acute pollution problems. Therefore, energy production from biomass, which has lower polluting potential due to its consumption of CO{sub 2} in the atmosphere and its low sulphur content, could be considered as an alternative solution. In this study, lignite-olive cake mixtures were burned in a fluidized bed combustor of 10 cm diameter. Temperature profiles, mechanisms of mixing and segregation, and gas emissions were investigated in the course of cocombustion. The lignite-olive cake mixture ratio and the coal particle size were selected as the experimental parameters. Temperature profiles of the fluidized bed show a lignite-olive cake flotsam rich behaviour and the effective parameter on segregation is the density difference between particles. The increase of the olive cake ratio in the mixture results in an important SO{sub 2} emissions decrease. The results also demonstrate that the NOx emissions remain at low values for all operating conditions.

  15. THE ALUMINA-SILICATES IN STABILIZATION PROCESSES IN FLUIDIZED-BED ASH

    Directory of Open Access Journals (Sweden)

    IVANA PERNA

    2011-03-01

    Full Text Available Presented study of coal fluidized-bed ash solidification was accompanied with specific studies of alumino-silicates residues in ashes. The specific technology of fluid coal burning and its relatively low temperature combustion combines coal burning and decomposition of calcium carbonate added to the fluid layer in the main endeavor to capture all sulfur oxides. The burning temperature seems be decisive to the behavior of clayed residues and calcium carbonate decomposition in connection for the future solidification of fluidized bed ash. The calcareous substances in combination with alumino-silicate residues form solid bodies where silicates play decisive role of long-term stability and insolubility of obtained solids. The position of aluminum ions in clayed residues of burned coal were studied by MAS-NMR with attention on aluminum ion coordination to oxygen and formation of roentgen amorphous phase of poly-condensed calcium alumina-silicate.

  16. Operating experience and development of fluidized-bed denitrators for UNH at Tokai Reprocessing Plant

    International Nuclear Information System (INIS)

    The fluidized bed denitrator for uranyl nitrate hexahydrate (UNH) at Tokai reprocessing plant has been operated since 1976. About 170 tons of spent fuel have been reprocessed, and the denitrator has encountered numerous operational problems during the period. This report deals with these technical problems and the associated countermeasures taken, including the dismantling and reconstruction of equipment and the improvement of operating method. The major problems encountered were as follows: (1) the crystallization of UNH on the UNH feeding line, (2) spray nozzle clogging and candle filter clogging, (3) particle growth, (4) plugging of the drawing-out line by nozzle caking, and (5) slugging in fluidized-bed denitration. The total quantity and quality of UO3 products obtained so far at the plant are also briefly described together with some future R and D programs such as the improvement of UO3 reactivity and the automation of denitrators. (Aoki, K.)

  17. Reduced Order Model of a Spouted Fluidized Bed Utilizing Proper Orthogonal Decomposition

    Science.gov (United States)

    Beck-Roth, Stephanie R.

    2011-07-01

    A reduced order model utilizing proper orthogonal decomposition for approximation of gas and solids velocities as well as pressure, solids granular temperature and gas void fraction for use in multiphase incompressible fluidized beds is developed and presented. The methodology is then tested on data representing a flat-bottom spouted fluidized bed and comparative results against the software Multiphase Flow with Interphase eXchanges (MFIX) are provided. The governing equations for the model development are based upon those implemented in the (MFIX) software. The three reduced order models explored are projective, extrapolative and interpolative. The first is an extension of the system solution beyond an original time sequence. The second is a numerical approximation to a new solution based on a small selected parameter deviation from an existing CFD data set. Finally an interpolative methodology approximates a solution between two existing CFD data sets both which vary a single parameter.

  18. Beckmann rearrangement of cyclohexanone oxime to {epsilon}-caprolactam using a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Dahlhoff, G.; Hoelderich, W.F. [Technische Hochschule Aachen (Germany)

    1999-07-01

    The application of a fluidized bed reactor on the heterogeneously catalyzed Beckmann rearrangement of cyclohexanone oxime to {epsilon}-caprolactam is presented. For this purpose the classic industrial synthesis route is compared to the new route catalyzed by [B]-MFI zeolite which proved to be the most suitable. To prepare the use of the catalyst the thermodynamics were calculated showing that the residence time of the reactants are of great importance. A regeneration model was developed resulting in a mathematical equation for the regeneration time calculated to seven hours under oxidative conditions. A 40 day regeneration experiment demonstrated the excellent regeneration behaviour of the chosen catalyst showing no decrease in activity after 40 recycle treatments. Finally, the experiments in a constructed non circulating fluidized bed showed good yields and selectivities (99%/91%) completely comparable to the actual synthesis route but avoiding 4 t ammonia sulphate/t product. (orig.)

  19. Using of fluidized-bed jet mill to a super fine comminution of steel composite

    Directory of Open Access Journals (Sweden)

    D. Urbaniak

    2015-01-01

    Full Text Available In many industries the demand for very fine material increases. In the metallurgical industry, for example, there is increasing use of the production of high density metal elements with the use of metallurgical powder composites. The use of powder composites requires prior their grinding. Unfortunately, the very fine grinding is not an easy process. The using for this purpose fluidized-bed jet mill was proposed in the paper. The attempts of grinding of metallurgical powder were carried out in the fluidized-bed jet mill. After the experiment analyses of particle size distribution of grinding products were performed. The results are presented in graphs. Analyses of the obtained results concluded that the grinding of very fine metallurgical composite is possible and produces positive results.

  20. Ash and heavy metals in fluidized bed-combustion; Tuhka ja raskasmetallit puuperaeisen jaetteen kerrosleijupoltossa

    Energy Technology Data Exchange (ETDEWEB)

    Kaessi, T.; Aittoniemi, P. [IVO International, Vantaa (Finland)

    1996-12-01

    Combustion ashes and submicron fly ash particles were characterized in two industrial boilers (bubbling vs. circulating fluidized bed) burning paper mill deinking sludge and bark or wood as support fuel. Bulk samples from fly ash, circulating ash and bottom ash were analyzed. Fine particles in fly ash were monitored and sampled for microscopic studies. The mass size distribution of fly ash was measured and the chemical composition according to particle size was analyzed. The results showed that ash consists of large and friable clusters formed by sintering of small mineral particles originating from paper fillers. Very few ash particles were fused and they were found only among the smallest particles. No agglomerates of fused particles were found. If the residence time in furnace is long enough sintering may proceed further and ash structure grows more dense. No indication of ash vaporization was detected. These results were similar for bubbling and circulating fluidized bed boilers. (author)

  1. Effect of Microwave on Fluidized Bed Drying of Beetroot (Beta vulgaris L.

    Directory of Open Access Journals (Sweden)

    Yashwant Kumar

    2016-07-01

    Full Text Available In the present work, an attempt has been made to study the effect of inlet air temperature and velocity on the drying characteristics of beetroot’s (Beta vulgaris L. pieces in microwave assisted fluidized bed drying (MAFBD system. The results were compared with samples of beetroot dried in a fluidized bed dryer (FBD at the same combination of temperatures and air velocities. The selected inlet air temperatures and inlet air velocities were 60°C, 67.50°C and 75°C and 9 m/s, 10.50 m/s and 12 m/s, respectively. Moisture content and outlet air humidity was measured at 5 minutes interval. The MAFBD method offered two to three times reduction in drying time as compared to the FBD method. It was also observed that the beetroot samples obtained from the MAFBD system had lower final moisture content than those obtained from the FBD system.

  2. Modeling and simulation of biomass air-steam gasification in a fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    By considering the features of fluidized-bed reactors and the kinetic mechanism of biomass gasification,a steady-state,isothermal,one-dimensional and twophase mathematical model of biomass gasification kinetics in bubbling fluidized beds was developed.The model assumes the existence of two phases - a bubble and an emulsion phase - with chemical reactions occurring in both phases.The axial gas dispersion in the two phases is accounted for and the pyrolysis of biomass is taken to be instantaneous.The char and gas species CO,CO2,H2,H2O,CH4 and 8 chemical reactions are included in the model.The mathematical model belongs to a typical boundary value problem of ordinary differential equations and its solution is obtained by a Matlab program.Utilizing wood powder as the feedstock,the calculated data show satisfactory agreement with experimental results and proves the effectiveness and reliability of the model.

  3. Carbon attrition during the circulating fluidized bed combustion of a waste-derived fuel

    Energy Technology Data Exchange (ETDEWEB)

    Arena, U. [Consiglio Nazionale delle Ricerche, Naples (Italy). Inst. for Combustion Research; Naples Univ. (Italy). Dept. of Environmental Sciences; Mastellone, M.L. [Naples Univ. Federico II (Italy). Dept. of Chemical Engineering

    1999-07-01

    A biomass obtained as residue from food manufacturing of pine nuts was batchwise fed in a laboratory scale circulating fluidized bed combustor. The apparatus was operated under both inert and oxidizing conditions in order to establish the relative importance of purely mechanical attrition and combustion-assisted attrition in generating carbon fines. For each run, carbon load and carbon particle size distribution in the riser and rates of attrited carbon fines escaping from the combustor were determined as a function of time. A parallel investigation was carried out with a bubbling fluidized bed combustor in order to point out peculiarities of attrition in the two apparatus. Results were compared with those obtained by burning in the same combustor a bituminous coal and a packaging-derived fuel, obtained from monomaterial collections of polyethylene terephtalate bottles. A different attrition phenomenology was found for each fuel and its peculiar features were taken into account. (orig.)

  4. Simultaneous determination of devolatilization and char burnout times during fluidized bed combustion of coal

    International Nuclear Information System (INIS)

    In this paper, the authors investigate a method for simultaneous determination of devolatilization and char burnout times based on the analysis of CO2 emissions from a fluidized bed combustor. The technique is not-intrusive and can be performed under realistic combustion conditions. The authors' method involves batching single-sized coal sample sin a fluidized bed combustor that is heated with propane gas or other fuel. Carbon dioxide profiles versus time for the batch tests are analyzed with a linear model to obtain characteristic time constants for coal devolatilization and char combustion which can be related to total devolatilization time and burnout time for a coal sample. The authors' approach does not require special sample preparation, can be performed in actual combustion equipment, and employs standard boiler instrumentation

  5. Simultaneous determination of devolatilization and char burnout times during fluidized bed combustion of coal

    International Nuclear Information System (INIS)

    In this paper, the authors investigate a method for simultaneous determination of devolatilization and char burnout times based on the analysis of CO2 emissions from a fluidized bed combustor. The technique is non-intrusive and can be performed under realistic combustion conditions. The authors' method involves batching single-size coal samples in a fluidized bed combustor that is heated with propane gas or other fuel. Carbon dioxide profiles versus time for the batch tests are analyzed with a linear model to obtain characteristic time constants for coal devolatilization and char combustion which can be related to total devolatilization time and burnout time for a coal sample. The authors' approach does not require special sample preparation, can be performed in actual combustion equipment and employs standard boiler instrumentation

  6. Flow Field of Circulating Fluidized Bed Reactor with Venturi Inlet Configuration

    Institute of Scientific and Technical Information of China (English)

    HU Jinbang; LI Yanping; CHEN Anxin

    2005-01-01

    Different two-equation k-ε models were used to simulate the gas flow field generated by a new type of circulating fluidized bed reactor with venturi gas distributor. The numerical results were compared with the experimental data. It has been shown that the simulation results from the standard k-ε model have the best match with the experimental data. Based on this model, the gas flow field in the venturi diffuser and riser was analyzed by the concept of velocity nonuniformity and dead zone percentage. Both the nonuniformity of gas velocity and the dead zone percentage reach the maximum at the venturi outlet due to the effect of the vortex. At the same time, it provides a good platform for the further optimization of the inlet configuration of circulating fluidized bed reactor.

  7. Control methods for remediation of ash-related problems in fluidized-bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Vuthaluru, H.B.; Zhang, D.

    1999-07-01

    The paper reports on investigations into control methodologies for mitigating ash-related problems such as particle agglomeration and bed defluidization during fluidized-bed combustion of low-rank coals. A laboratory scale spouted bed combustor is used to study the effectiveness of control methodologies. In the present work, two control methods are investigated viz., the use of alternative bed materials and pretreatment of coal. Bauxite and calcined sillimanite are used as alternative bed materials in the spouted bed combustor while burning South Australian low-rank coal. Samples of the same coal subjected to Al pretreatment, water washing and acid washing are also tested in the spouted bed combustor. Experiments showed that both methods are effective to different extents in reducing ash-related problems. Tests with calcined sillimanite and bauxite (as the bed material) showed trouble free operation for longer periods (7--12 hr at 800 C and 3--5 hr at 850 C) than with sand runs at the same bed temperatures. Al pretreatment and water-washing were also found to be effective and resulted in extended combustion operation. Al enrichment in ash coating of bed particles has been identified as the main mechanism for prevention of agglomeration and defluidization by these control methodologies. For water-washing, the principal reason behind agglomeration and defluidization control is the reduction in sodium levels.

  8. Formation and removal of biomass-derived contaminants in fluidized-bed gasification processes

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1996-12-31

    The objectives of this thesis were to examine the effects of the feedstock and the operating conditions of a fluidized-bed gasifier on the formation of tars and nitrogen-containing compounds and to study the effectiveness of the hot gas cleaning methods developed for the removal of particulates, alkali metals, tars and nitrogen-containing compounds. The most essential part of the work was carried out in the pressurized fluidized-bed gasification test facilities composed of an air-blown bubbling fluidized-bed gasifier and subsequent hot gas filter unit. The operation pressure of the test rig could be varied in the range 0.3 - 1.0 MPa and the maximum allowable gasification temperature was 1 050 deg C. The maximum capacity with biomass fuels was 80 kg/h. A wide range of feedstocks from hard coals, lignite and peat to different wood derived fuels and straw were used in the gasification tests. Two different types of ceramic filters were tested in the filter unit connected to the pressurized fluidized-bed gasifier. The filter unit was operated in a temperature range of 400 - 740 deg C. The particulate removal requirements set by the gas turbines were met by both types of filters and with product gases derived from all the feedstocks tested. In addition to the gasification and gas filtration tests, catalytic tar and ammonia decomposition was studied using both laboratory and bench-scale test facilities. Inexpensive calcium-based bulk materials, dolomites and limestones, were efficient tar decomposition catalysts in atmospheric-pressure tests

  9. Chemical Looping Reactor System Design : Double Loop Circulating Fluidized Bed (DLCFB)

    OpenAIRE

    Bischi, Aldo

    2012-01-01

    Chemical looping combustion (CLC) is continuously gaining more importance among the carbon capture and storage (CCS) technologies. It is an unmixed combustion process which takes place in two steps. An effective way to realize CLC is to use two interconnected fluidized beds and a metallic powder circulating among them, acting as oxygen carrier. The metallic powder oxidizes at high temperature in one of the two reactors, the air reactor (AR). It reacts in a highly exothermic reaction with the ...

  10. Coal. Fluidized bed, a world record; Charbon. Lit fluidise: record mondial

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-12-31

    In April 1996, the `Societe Provencale du Lit Fluidise`, a subsidiary of Electricite de France (EDF) has put into service in Gardanne, the most powerful circulating fluidized bed boiler in the world, producing 600 MWt; it was constructed by GEC Alsthom Stein Industrie, and will strongly reduce the SO{sub 2} emissions from the coal power plant of Gardanne, which use a highly sulfurous coal. New regulations concerning the French coal industry are also introduced

  11. Proceedings of the sixth international conference on fluidized bed combustion. Volume III. Technical sessions

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-08-01

    The Sixth International Conference on Fluidized Bed Combustion was held April 9-11, 1980, at the Atlanta Hilton, Atlanta, Georgia. It was sponsored by the US Department of Energy, the Electric Power Research Institute, the US Environmental Protection Agency, and the Tennessee Valley Authority. Forty-five papers from Vol. III of the proceedings have been entered individually into EDB and ERA. Two papers had been entered previously from other sources. (LTN)

  12. Simulation for Supporting Scale-Up of a Fluidized Bed Reactor for Advanced Water Oxidation

    OpenAIRE

    Farhana Tisa; Abdul Aziz Abdul Raman; Wan Mohd Ashri Wan Daud

    2014-01-01

    Simulation of fluidized bed reactor (FBR) was accomplished for treating wastewater using Fenton reaction, which is an advanced oxidation process (AOP). The simulation was performed to determine characteristics of FBR performance, concentration profile of the contaminants, and various prominent hydrodynamic properties (e.g., Reynolds number, velocity, and pressure) in the reactor. Simulation was implemented for 2.8 L working volume using hydrodynamic correlations, continuous equation, and simp...

  13. A small scale regularly packed circulating fluidized bed. Part I: Hydrodynamics.

    OpenAIRE

    Ham, van, M.; Prins, W.; Swaaij, van, Wim P.M.

    1994-01-01

    The present investigation is based on the idea of intensifying the gas¿solids contact in a circulating fluidized bed by introducing obstacles into it. Such obstacles may effectively suppress radial inhomogeneities in the solids flux and concentration, increase the dynamic solids hold-up, and break up solids clusters. This article (Part I) deals with the hydrodynamics (pressure drop and solids hold-up) investigated at ambient conditions, for cocurrent upward flow of air and microsize solid par...

  14. Proceedings of the Sixth International Conference on Fluidized Bed Combustion. Volume 1. Plenary sessions

    Energy Technology Data Exchange (ETDEWEB)

    None

    1980-08-01

    The Sixth International Conference on Fluidized Bed Combustion was held at the Atlanta Hilton, Atlanta, Georgia, April 9-11, 1980. The papers in this volume involved presentation of the research and development programs of the US (US DOE, TVA, EPRI and US EPA), United Kingdom, Federal Republic of Germany and the People's Republic of China. Eight papers from Vol. 1 (Plenary Sessions) of the proceedings have been entered individually into EDB and ERA. (LTN)

  15. Production of ethanol by solid particles of Saccharomyces cerevisiae in a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Moebus, O.; Teuber, M.

    1982-01-01

    CO/sub 2/ can be used as the fluid continuous phase for the fermentation of 10-40% aqueous solutions of glucose to ethanol with S. cerevisiae using a closed circuit consisting of a fluidized bed of small solid yeast particles, a cooled condenser for the sampling of water and ethanol, and a blower. At 80 degrees, a fermentation of 12 mu mol glucose/minute-g dry yeast was achieved.

  16. CFD simulation on hydrodynamics in fluidized beds: assessment of gradient approximations and turbulence models

    Science.gov (United States)

    Guo, Yuan; Deng, Baoqing; Ge, Daqiang; Shen, Xiuzhong

    2015-08-01

    CFD simulations of gas-solid fluidized beds have been performed in Euler-Euler framework. Green-Gauss Cell Based gradient approximation can predict the solid velocity well among gradient approximations. The dispersed choice in the turbulence model can reproduce the solid velocity correctly while the mixture and per phase choices cannot. The standard k-ɛ model, RNG k-ɛ model and SST k-ω model with the dispersed choice can predict the solid velocity well.

  17. Surface Modification of Polymer Powders by a Far Cold Remote Nitrogen Plasma in Fluidized Bed

    Science.gov (United States)

    Alfaro-López, H. M.; Aiche, Lynda.; Vergnes, Hugues.; Despax, Bernard.; Caussat, Brigitte.; Caquineau, Hubert.

    In this work, nitrogen was grafted on the surface of polyethylene powders in a fluidized bed coupled to a nitrogen microwave post-discharge, under low pressure (10Torr) and low temperature (<90°C). The influences of treatment-duration (1 to 9 h) and nitrogen flow-rate on the XPS (X-ray Photoelectron Spectroscopy) N/C atomic ratio and on the powder wettability have been studied

  18. Microstructure characterization of fluidized bed nitrided Fe–Si and Fe–Si–Al foils

    Indian Academy of Sciences (India)

    H Atmani; O Thoumire

    2002-06-01

    This work deals with the structural modifications of FeSi and FeSiAl foils when subjected to a thermochemical nitriding treatment (TNT) performed in a fluidized-bed laboratory furnace. The investigations on the nitrided samples were carried out by optical and SEM microscopic observations, X-ray diffraction and Mössbauer spectroscopy. Both the compound and diffusion layers were investigated.

  19. Synthesis of a nanosilica supported CO2 sorbent in a fluidized bed reactor

    International Nuclear Information System (INIS)

    Highlights: • CaO coating at atmospheric pressure is applied on silica nanoparticles in a fluidized bed. • Atmospheric pressure would facilitate scaling-up of the process. • The conditions for the coating process at atmospheric pressure are discussed. • The CO2 sorbent capacity is demonstrated by TGA in carbonation/calcination. • STEM-EDX shows the presence of CaO on the surface of the nanoparticles. - Abstract: CaO has been deposited on a nanosilica powder matrix by a procedure based on atomic layer deposition (ALD) in a fluidized bed reactor at atmospheric pressure following a potentially scalable process. In previous works ALD in gas fluidized bed has been mostly performed under reduced pressure, which hampers scaling-up the production technology. The material synthesized in the present work is tested as CO2 solid sorbent at calcium looping conditions. Multicyclic thermogravimetric analysis (TGA) shows that the nanosilica support stabilizes the capture capacity of CaO. EDX-STEM analysis illustrates the presence of Ca well distributed on the surface of the SiO2 nanoparticles

  20. Modelling of a circulating fluidized bed using computational fluid dynamic software

    Energy Technology Data Exchange (ETDEWEB)

    Torres, E.C.; Steward, F. [New Brunswick Univ., Centre for Nuclear Research, Fredericton, NB (Canada); Pugsley, T. [New Brunswick Univ., Dept. of Chemical Engineering, Fredericton, NB (Canada)

    1998-09-01

    A computational fluid dynamics (CFD) software called `FLUENT` was used to model the hydrodynamics of the riser of a laboratory scale circulating fluidized bed. A circulating fluidized bed is a type of fluidized bed that operates at high gas velocities. Its two most important applications are for combustion purposes and for fluid catalytic cracking. Results from the simulated cold model were compared with experimental data. Predictions of the model were in good agreement with trends observed experimentally.The two main considerations when applying CFD to the experimental set-up are granular multiphase models and the turbulence conditions for the gas and solid phases. The time dependent model provides outputs that predict the radial and axial distribution of the gas and solids in the riser which correspond to different operating conditions of riser solids mass flux and gas velocity. By introducing more accurate particle flow data at the entrance and at the walls into the boundary conditions the CFD model could be significantly improved.9 refs., 1 tab., 10 figs.

  1. ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Wei-Ping Pan; Andy Wu; John T. Riley

    2005-07-30

    This purpose of this report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period April 1, 2005 through June 30, 2005. The following tasks have been completed. First, the new Combustion Laboratory was occupied on June 15, 2005, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final painting stage. Second, the fabrication and manufacturing contract for the CFBC Facility was awarded to Sterling Boiler & Mechanical, Inc. of Evansville, Indiana. Sterling is manufacturing the assembly and component parts of the CFBC system. The erection of the CFBC system is expected to start September 1, 2005. Third, mercury emissions from the cofiring of coal and chicken waste was studied experimentally in the laboratory-scale simulated fluidized-bed combustion facility. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter is described.

  2. Industrial demonstration plant for the gasification of herb residue by fluidized bed two-stage process.

    Science.gov (United States)

    Zeng, Xi; Shao, Ruyi; Wang, Fang; Dong, Pengwei; Yu, Jian; Xu, Guangwen

    2016-04-01

    A fluidized bed two-stage gasification process, consisting of a fluidized-bed (FB) pyrolyzer and a transport fluidized bed (TFB) gasifier, has been proposed to gasify biomass for fuel gas production with low tar content. On the basis of our previous fundamental study, an autothermal two-stage gasifier has been designed and built for gasify a kind of Chinese herb residue with a treating capacity of 600 kg/h. The testing data in the operational stable stage of the industrial demonstration plant showed that when keeping the reaction temperatures of pyrolyzer and gasifier respectively at about 700 °C and 850 °C, the heating value of fuel gas can reach 1200 kcal/Nm(3), and the tar content in the produced fuel gas was about 0.4 g/Nm(3). The results from this pilot industrial demonstration plant fully verified the feasibility and technical features of the proposed FB two-stage gasification process. PMID:26849201

  3. Analysis of fluidized bed granulation process using conventional and novel modeling techniques.

    Science.gov (United States)

    Petrović, Jelena; Chansanroj, Krisanin; Meier, Brigitte; Ibrić, Svetlana; Betz, Gabriele

    2011-10-01

    Various modeling techniques have been applied to analyze fluidized-bed granulation process. Influence of various input parameters (product, inlet and outlet air temperature, consumption of liquid-binder, granulation liquid-binder spray rate, spray pressure, drying time) on granulation output properties (granule flow rate, granule size determined using light scattering method and sieve analysis, granules Hausner ratio, porosity and residual moisture) has been assessed. Both conventional and novel modeling techniques were used, such as screening test, multiple regression analysis, self-organizing maps, artificial neural networks, decision trees and rule induction. Diverse testing of developed models (internal and external validation) has been discussed. Good correlation has been obtained between the predicted and the experimental data. It has been shown that nonlinear methods based on artificial intelligence, such as neural networks, are far better in generalization and prediction in comparison to conventional methods. Possibility of usage of SOMs, decision trees and rule induction technique to monitor and optimize fluidized-bed granulation process has also been demonstrated. Obtained findings can serve as guidance to implementation of modeling techniques in fluidized-bed granulation process understanding and control. PMID:21839830

  4. Prediksi Potensi Pencemaran Pengolahan Sampah dengan Metode Gasifikasi Fluidized Bed (Studi Kasus: TPA Benowo, Surabaya

    Directory of Open Access Journals (Sweden)

    Lailatun Nikmah

    2013-03-01

    Full Text Available Sistem pengelolaan sampah di TPA Benowo masih bersistem open dumping dan belum memperhatikan dampak pencemaran terhadap lingkungan. Kuantitas sampah yang masuk ke TPA sebesar 461.705,782 ton pada tahun 2012. Kuantitas sampah diperkirakan meningkat sebanding dengan pertumbuhan penduduk, sehingga dibutuhkan skenario pengolahan sampah yang ramah lingkungan. Skenario pengolahan sampah yang akan dikaji adalah gasifikasi  fluidized bed. Potensi pencemaran gasifikasi  fluidized bed akan dikaji menggunakan metode Life Cycle Assessment (LCA dengan software SimaPro versi 7.1. Satu ton sampah pada studi ini ditentukan sebagai satu fungsi unit. Data input Life Cycle Inventory (LCI meliputi jumlah sampah yang masuk ke reaktor gasifikasi dan energi yang dibutuhkan pada proses gasifikasi berdasarkan pendekatan efisiensi reaktor gasifikasi. Penentuan nilai Life Cycle Impact Assesment (LCIA meliputi Global Warming Potential (GWP dan asidifikasi menggunakan metode Environmental Product Declarations (EPD 2008. Besar dampak dinyatakan dalam faktor emisi yang ekivalen. Kesimpulan pada penelitian ini menunjukkan bahwa skenario pengolahan sampah dengan metode gasifikasi fluidized bed memberikan dampak GWP sebesar 1067,8 kg CO2/fu pada fase start-up dan 875 kg CO2/fu pada fase energy recovery serta asidifikasi sebesar 5,93 kg SO2/fu pada fase start-up dan 4,81 kg SO2/fu pada fase energy recovery.

  5. Prediction of the position of coal particles in an air dense medium fluidized bed system

    Institute of Scientific and Technical Information of China (English)

    Prusti Pallishree; Sahu Ashok K.; Biswal Surendra K

    2015-01-01

    An air dense medium fluidized bed separator (ADMFBS) is used for dry beneficiation of coal using ultra-fine magnetite particles as a pseudo-fluid medium. In this process, the coal particle gains additional weight due to coating on its surface and deposition at dead zone area by fine magnetite particles. Hence, the effective density of coal particle increases and the position of coal particle changes accord-ingly. In this work, an attempt was made to predict the position of coal particle in non-bubbling condition dense medium fluidized bed system. Coal particles of different shape such as cubical, rectangular prism, spherical and triangular prism with different projected area and density were used. The results show that the position of coal particle in air dense medium fluidized bed follows descending order with respect to the increase of density, projected area of coal particle and different shapes (i.e., triangular prism, cubical, rectangular prism and spherical). Empirical mathematical correlations were developed to predict the position of coal particle.

  6. Materials performance in the atmospheric fluidized-bed cogeneration air heater experiment

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Podolski, W.; Wang, D.Y.; Teats, F.G. (Argonne National Lab., IL (United States)); Gerritsen, W.; Stewart, A.; Robinson, K. (Rockwell International Corp., Canoga Park, CA (United States))

    1991-02-01

    The Atmospheric Fluidized-Bed Cogeneration Air Heater Experiment (ACAHE) sponsored by the US Department of Energy (DOE) was initiated to assess the performance of various heat-exchanger materials to be used in fluidized-bed combustion air heater systems. Westinghouse Electric Corporation, through subcontracts with Babcock Wilcox, Foster Wheeler, and ABB Combustion Engineering Systems, prepared specifications and hardware for the ACAHE tests. Argonne National Laboratory contracted with Rockwell International to conduct tests in the DOE atmospheric fluidized-bed combustion facility. This report presents an overview of the project, a description of the facility and the test hardware, the test operating conditions, a summary of the operation, and the results of analyzing specimens from several uncooled and cooled probes exposed in the facility. Extensive microstructural analyses of the base alloys, claddings, coatings, and weldments were performed on specimens exposed in several probes for different lengths of time. Alloy penetration data were determined for several of the materials as a function of specimen orientation and the exposure location in the combustor. Finally, the data were compared with earlier laboratory test data, and the long-term performance of candidate materials for air-heater applications was assessed.

  7. Materials performance in the atmospheric fluidized-bed cogeneration air heater experiment

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Podolski, W.; Wang, D.Y.; Teats, F.G. [Argonne National Lab., IL (United States); Gerritsen, W.; Stewart, A.; Robinson, K. [Rockwell International Corp., Canoga Park, CA (United States)

    1991-02-01

    The Atmospheric Fluidized-Bed Cogeneration Air Heater Experiment (ACAHE) sponsored by the US Department of Energy (DOE) was initiated to assess the performance of various heat-exchanger materials to be used in fluidized-bed combustion air heater systems. Westinghouse Electric Corporation, through subcontracts with Babcock & Wilcox, Foster Wheeler, and ABB Combustion Engineering Systems, prepared specifications and hardware for the ACAHE tests. Argonne National Laboratory contracted with Rockwell International to conduct tests in the DOE atmospheric fluidized-bed combustion facility. This report presents an overview of the project, a description of the facility and the test hardware, the test operating conditions, a summary of the operation, and the results of analyzing specimens from several uncooled and cooled probes exposed in the facility. Extensive microstructural analyses of the base alloys, claddings, coatings, and weldments were performed on specimens exposed in several probes for different lengths of time. Alloy penetration data were determined for several of the materials as a function of specimen orientation and the exposure location in the combustor. Finally, the data were compared with earlier laboratory test data, and the long-term performance of candidate materials for air-heater applications was assessed.

  8. Recent status of fluidized bed technologies for producing iron input materials for steelmaking

    Institute of Scientific and Technical Information of China (English)

    Johannes Leopold Schenk

    2011-01-01

    Today steel is produced by two steelmaking processes,the basic oxygen furnace and the electric arc furnace. Three types of iron input materials for both processes are liquid hot metal or in solidified form as pig iron,direct reduced iron (DRI) and hot briquetted iron (HBI) as well as steel scrap. Hot metal,pig iron,DRI and HBI are virgin iron materials,which have to be produced from iron ore by the so-called ironmaking technologies.New ironmaking processes based on fluidized bed technology have been developed in the last two decades. The main advantage of these technologies is that fine ore can be directly used in the processes and prior treatment such as sintering or pelletizing can be avoided which is required for the established processes. Theoretical aspects for reduction of fine iron oxides in a fluidized bed reactor system will be explained. The fluidized bed reducing technologies utilized in the most advanced new ironmaking processes for direct use of fine ore,FINMET(R),Circored(R),FINEX(R) and Hlsmelt(R) will be compared.

  9. ESTABLISHMENT OF AN ENVIRONMENTAL CONTROL TECHNOLOGY LABORATORY WITH A CIRCULATING FLUIDIZED-BED COMBUSTION SYSTEM

    Energy Technology Data Exchange (ETDEWEB)

    Wei-Ping Pan; Andy Wu; John T. Riley

    2005-04-30

    This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period January 1, 2005 through March 31, 2005. The following tasks have been completed. First, the renovation of the new Combustion Laboratory is nearly complete, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final stages. Second, the fabrication and manufacture of the CFBC Facility is being discussed with a potential contractor. Discussions with potential contactor regarding the availability of materials and current machining capabilities have resulted in the modification of the original designs. The selection of the fabrication contractor for the CFBC Facility is expected during the next quarter. Third, co-firing experiments conducted with coal and chicken waste have been initiated in the laboratory-scale simulated fluidized-bed facility. The experimental results from this study are presented in this report. Finally, the proposed work for the next quarter is described in this report.

  10. Synthesis of a nanosilica supported CO{sub 2} sorbent in a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Soria-Hoyo, C., E-mail: cshoyo@us.es [Facultad de Física, Universidad de Sevilla, Avda. Reina Mercedes s/n, 41012 Sevilla (Spain); Valverde, J.M. [Facultad de Física, Universidad de Sevilla, Avda. Reina Mercedes s/n, 41012 Sevilla (Spain); Ommen, J.R. van [Department of Chemical Engineering, Delft University of Technology, Product and Process Engineering, Julianalaan 136, 2628 BL Delft (Netherlands); Sánchez-Jiménez, P.E.; Pérez-Maqueda, L.A.; Sayagués, M.J. [Instituto de Ciencia de Materiales (CSIC – Universidad de Sevilla), Americo Vespucio 49, 41092 Sevilla (Spain)

    2015-02-15

    Highlights: • CaO coating at atmospheric pressure is applied on silica nanoparticles in a fluidized bed. • Atmospheric pressure would facilitate scaling-up of the process. • The conditions for the coating process at atmospheric pressure are discussed. • The CO{sub 2} sorbent capacity is demonstrated by TGA in carbonation/calcination. • STEM-EDX shows the presence of CaO on the surface of the nanoparticles. - Abstract: CaO has been deposited on a nanosilica powder matrix by a procedure based on atomic layer deposition (ALD) in a fluidized bed reactor at atmospheric pressure following a potentially scalable process. In previous works ALD in gas fluidized bed has been mostly performed under reduced pressure, which hampers scaling-up the production technology. The material synthesized in the present work is tested as CO{sub 2} solid sorbent at calcium looping conditions. Multicyclic thermogravimetric analysis (TGA) shows that the nanosilica support stabilizes the capture capacity of CaO. EDX-STEM analysis illustrates the presence of Ca well distributed on the surface of the SiO{sub 2} nanoparticles.

  11. DEM simulation of polydisperse systems of particles in a fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Nobuyuki Tagami; Ajit Mujumdar; Masayuki Horio

    2009-01-01

    Numerical simulations based on three-dimensional discrete element model (DEM) are conducted for mono-disperse, binary and ternary systems of particles in a fluidized bed. Fluid drag force acting on each particle depending on its size and relative velocity is assigned. The drag coefficient corresponding to Ergun's correlation is applied to the system of fluidized bed with particle size ratios of 1:1 for the mono-disperse system, 1:1.2, 1:1.4 and 1:2 for the binary system and 1:1.33:2 for the ternary system by keeping total volume and surface area of the particles constant. Results indicated that a reasonable estimation of drag force based on individual particle diameters as compared to that of the mean diameter of the particles is achieved in the fluid cells. The total translational kinetic energy of the particles is found to increase as the particle size ratio increases, suggesting an enhanced momentum transfer in polydisperse particle systems. Systems with wide particle size distribution exhibited higher particle velocities around bubbles, resulting in faster bubble growth and its subsequent rise through the fluidized bed.

  12. Magnetically assisted gas-solid fluidization in a tapered vessel: Part Ⅱ Dimensionless bed expansion scaling

    Institute of Scientific and Technical Information of China (English)

    Jordan Hristov

    2009-01-01

    The article presents an effort to create dimensionless scaling correlations of the overall bed porosity in the case of magnetically assisted fluidization in a tapered vessel with external transverse magnetic field. This is a stand of portion of new branch in the magnetically assisted fluidization recently created con-cerning employment of tapered vessels. Dimensional analysis based on "pressure transform" of the initial set of variables and involving the magnetic granular Bond number has been applied to develop scaling relationships of dimensionless groups representing ratios of pressures created by the fluid flow, gravity and the magnetic field over an elementary volume of the fluidized bed. Special attention has been paid on the existing data correlations developed for non-magnetic beds and the links to the new ones especially developed for tapered magnetic counterparts. A special dimensionless variable Xp = (Ar△DbL)1/3(√RgMQ) combining Archimedes and Rosensweig numbers has been conceived for porosity correlation. Data cor-relations have been performed by power-law, exponential decay and asymptotic functions with analysis of their adequacies and accuracies of approximation.

  13. Hydrogen production by biomass gasification in supercritical water with a fluidized bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Y.J.; Jin, H.; Guo, L.J.; Zhang, X.M.; Cao, C.Q.; Guo, X. [State Key Laboratory of Multiphase Flow in Power Engineering (SKLMF), Xi' an Jiaotong University, 28 Xianning West Road, Xi' an 710049, Shaanxi (China)

    2008-11-15

    Hydrogen production by biomass gasification in supercritical water (SCW) is a promising technology for utilizing high moisture content biomass, but reactor plugging is a critical problem for biomass gasification in the tubular reactor. A novel SCW fluidized bed system for biomass gasification was developed successfully in State Key Laboratory of Multiphase Flow in Power Engineering (SKLMF) to prevent the plugging and it was designed for the temperature up to 923 K and the pressure up to 30 MPa. Model compound (glucose) and real biomass (corn cob) were gasified under SCW conditions to generate hydrogen-rich fuel gas and a performance testing of the new SCW fluidized bed system was conducted. The product gas composed of H{sub 2}, CH{sub 4}, CO{sub 2}, CO and small amount of C{sub 2}H{sub 4} and C{sub 2}H{sub 6} was obtained. The effects of solution concentration, temperature, pressure and oxidant concentration on gasification were studied. 30 wt% glucose and 18 wt% corn cob feedstocks were continually and stably gasified and reactor plugging was not observed. The results showed that using fluidized bed reactor for biomass gasification in SCW has many advantages and good prospects. (author)

  14. Multi-stage circulating fluidized bed syngas cooling

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Guohai; Vimalchand, Pannalal; Guan, Xiaofeng; Peng, WanWang

    2016-10-11

    A method and apparatus for cooling hot gas streams in the temperature range 800.degree. C. to 1600.degree. C. using multi-stage circulating fluid bed (CFB) coolers is disclosed. The invention relates to cooling the hot syngas from coal gasifiers in which the hot syngas entrains substances that foul, erode and corrode heat transfer surfaces upon contact in conventional coolers. The hot syngas is cooled by extracting and indirectly transferring heat to heat transfer surfaces with circulating inert solid particles in CFB syngas coolers. The CFB syngas coolers are staged to facilitate generation of steam at multiple conditions and hot boiler feed water that are necessary for power generation in an IGCC process. The multi-stage syngas cooler can include internally circulating fluid bed coolers, externally circulating fluid bed coolers and hybrid coolers that incorporate features of both internally and externally circulating fluid bed coolers. Higher process efficiencies can be realized as the invention can handle hot syngas from various types of gasifiers without the need for a less efficient precooling step.

  15. Properties of Concrete Incorporating Bed Ash from Circulating Fluidized Bed Combustion and Ground Granulates Blast-furnace Slag

    Institute of Scientific and Technical Information of China (English)

    CHENG An; HSU Hui-Mi; CHAO Sao-Jeng

    2011-01-01

    The properties of concrete incorporating circulating fluidized bed combustion (CFBC) bed ash and ground granulates blast-furnace slag (GGBS) were studied. Compressive strength,drying shrinkage, mercury intrusion porosimetry (MIP), scanning electronic microscopy (SEM), and X-ray diffraction (XRD) of concrete samples containing CFBC bed ash and GGBS were used. This work used initial surface absorption test (ISAT) and rapid chloride penetration test (RCPT) on concrete to measure the absorption and the ability of concrete to resist chloride ion characteristics for different concrete samples containing CFBC bed ash and GGBS. Open circuit potential (OCP), direct current polarization resistance were obtained to evaluate rebar corrosion. The CFBC bed ash was X-ray amorphous and consist of SiO2, A12O3 and CaO compounds. As the replacement of CFBC for sand increases, the rate of initial surface absorption (ISA) increases but compressive strength decreases.When the content of CFBC bed ash replacement for sand maintains constant, the replacement of GGBS for cement increases, compressive strength increases but the rate of ISA decreases. Chloride and corrosion resistance of rebar significantly improve by utilizing a proper amount of CFBC bed ash and GGBS in concrete.

  16. Sorption Characteristics of Organic Powder Sorption Material in Fluidized Bed with a Cooling Pipe

    Science.gov (United States)

    Horibe, Akihiko; Husain, Syahrul; Inaba, Hideo; Haruki, Naoto

    The dynamic sorption characteristics of organic sorbent materials have been studied by using fluidized bed with a cooling pipe. The organic powder type sorbent made from a bridged complex of sodium polyacrylate which is one of the sorption polymers is adopted in this study. Sorption rate of water vapor and the variation of temperature in the sorbent bed with time were measured under various conditions. As a result, sorption ratio increases and the completion time for the sorption process decreases by using a cooling pipe. Furthermore, the non-dimensional correlation equations were obtained for water vapor mass transfer under sorption process in terms of relevant non-dimensional parameters.

  17. Axial Liquid Dispersion in Gas-Liquid-Solid Circulating Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    M.Vatanakul; 孙国刚; 郑莹; M.Couturier

    2005-01-01

    The effects of liquid viscosities, solid circulating rates, liquid and gas velocities and phase holdups on the axial dispersion coefficient, Dax, were investigated in a gas-liquid-solid circulating fluidized bed (GLSCFB).Liquid viscosity promotes the axial liquid backmixing when solid particles and gas bubbles are present. Increases in gas velocities and solid circulating rates lead to higher Dax. The effects of liquid velocity on Dax are associated with liquid viscosity. Compared with conventional expanded beds, the GLSCFBs hold less axial liquid dispersion,approaching ideal plug-flow reactors.

  18. A Mathematical Model for Differential—Velocity Circulating Fluidized Bed Boiler

    Institute of Scientific and Technical Information of China (English)

    LiZhao; XiangdongXu

    1999-01-01

    The scheme of differential-velocity circulating fluidized bed was put forward by Thermal Engineering Department of Tsinghua university in 1992 and got patent simultaneously.An internal bed material circulation in combustor can be established by the discrepancy of entrainment at different air velocity,and separates the combustor into three different velocity regions,which constitutes the differential-velocity inside circulation.Mathematical modeling and simulation may facilitate understanding,Development and operation of this new process.Here cell model method was adopted to set up the model.

  19. Lateral Solids Mixing in the Dense Zone of a Circulating Fluidized Bed

    Institute of Scientific and Technical Information of China (English)

    YANGHairui; LUEJunfu; 等

    2002-01-01

    Lateral solid mixing was investigated experimentally in the dense zone of a 900mm×100mm×5.2m rectangular circulating fluidized bed riser.Using heated tracer injection,the lateral solid dispersion was determined by measuring the temperature response at different lateral positions. Furthermore, a one-dimensional dispersion model,which describes the solid mixing in the dense zone,is presented.The experimental results were used to determine the lateral particle dispersion coefficient under various operating conditions. A correlation of dispersion coefficient with bed height, gas velocity,and particle size is also proposed.

  20. EXTERNAL-LOOP AIRLIFT MAGNETICALLY STABILIZED BED--MINIMUM STABILIZATION AND FLUIDIZATION CONDITIONS

    Institute of Scientific and Technical Information of China (English)

    Jordan Hristov

    2005-01-01

    Experimental study of an airlift with a magnetically stabilized bed in the riser bottom has been performed.External magnetic field allows easy control of magnetized bed structure and liquid circulation rate. Minimum stabilization and fluidization conditions have been determined experimentally and by a three-line graphical method. Semi-empirical data correlations of sections of the experimental curves have been performed. Scaling relationships known from non-magnetic airlift are applicable too, but with the assumption that the magnetic field affects the loop friction coefficient only.

  1. Mechanisms of formation and destruction of nitrogen oxides during polyamide incineration in a fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Hahnel, F.; Gadiou, R.; Prado, G. [Univ. de Haute Alsace, Mulhouse (France). Lab. de Gestion des Risques et Environnement

    1998-09-01

    In order to study the incineration of nitrogen-containing polymers, a fludized bed has been built. This paper reports the results for polyamide 6-6 incineration. The main nitrogen containing species have been identified, and the axial profiles of concentration of nitrogen oxides, HCN and NH3 have been measured. The main steps of decomposition of the polyamide were identified. We present an experimental investigation of the influence of operating parameters (temperature, excess air) on the formation and reduction of polymer combustion products. The yields of conversion of nitrogen to the different N-species have been calculated as a function of excess air in the fluidized bed. (orig.)

  2. Flow visualizing study of fluidized bed for incineration and/or coal combustion technology

    Energy Technology Data Exchange (ETDEWEB)

    Ozawa, Mamoru [Kansai Univ., Suita, Osaka (Japan). Faculty of Engineering

    1997-02-01

    A simulated fluidized-bed heat exchanger was visualized using a neutron radiography system. The void fraction distribution and its fluctuation were obtained by means of an image processing technique. On the basis of the processed image, the mechanism of a large particle movement and the flow pattern in the tube bank immersed in the bed were investigated. Observed flow pattern in the tube bank indicated an importance of the tube arrangement on the void fraction fluctuation and thus the heat transfer around tubes. (author)

  3. Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

    Energy Technology Data Exchange (ETDEWEB)

    Jonassen, Ola

    1999-07-01

    The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidizing gas,(3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

  4. Hydrodynamic study of the turbulent fluidized beds; Etude hydrodynamique des lits fluidises turbulents

    Energy Technology Data Exchange (ETDEWEB)

    Taxil, I.

    1996-12-20

    Gas-solid turbulent fluidization has already been widely studied in the literature. However, its definition and specificities remain controversial and confused. Most of the studies focussed on the turbulent transition velocities are based on wall pressure drop fluctuations studies. In this work, we first characterize the turbulent regime with the classical study of pressure drop signals with standard deviation analysis, completed with a more specific frequency analysis and also by a stochastic analysis. Then, we evaluate bubble flow properties. Experimental results have been obtained in a 0.2 m I.D. fluidized bed expanding to 0.4 m I.D. in the freeboard in order to limit entrainment at high fluidization velocities. The so lid used was FCC catalyst. It was fluidized by air at ambient conditions. The superficial fluidization velocity ranged 0.2 to 2 m/s. Fast response transducers recorded pressure drop at the wall and bubble flow properties (bubble size, bubble velocity and bubble frequency) could be deduced from a light reflected signal at various bed locations with optical fibers. It has been shown the turbulent regime is delimited by two velocities: Uc (onset of turbulent regime) and Utr (onset of transport regime), which can be determined based on standard deviations, dominant frequencies and width of wave land of pressure signals. The stochastic analysis confirms that the signal enriches in frequencies in the turbulent regime. Bubble size and bubble velocity could be correlated to the main superficial gas velocity. The main change in bubble flow in the turbulent regime was shown to be the stagnation of the bubble frequency at its maximum value. It was also shown that the bubble flow properties in the turbulent regime imply a strong aeration of the emulsion phase. (authors) 76 refs.

  5. Characterization of residues from waste combustion in fluidized bed boilers. Evaluation report

    International Nuclear Information System (INIS)

    In this report a thorough characterization of the solid residues from municipal solid waste combustion in a Kvaerner EnviroPower bubbling fluidized bed boiler in Lidkoeping, is presented. Three different end products are generated, namely bottom ash, cyclone ash, and filter ash. The bottom ash, consisting of bed ash and hopper ash, is screened and useful bed material recycled. In the characterization, also the primary constituents bed ash and hopper ash have been included. A chemical characterization have been performed including total inorganic contents, content of unburnt matter, leaching behaviour (availability tests, column tests, pH-static tests) and leaching tests according to certain standards for classification (AFX31-210, DIN38414, TCLP). Physical characterization have included grain size distribution, grain density, compaction properties and stabilization of cyclone ash with subsequent testing of comprehensive strength and saturated hydraulic conductivity. From an environmental point of view, the quality of the bottom ash and probably the cyclone ash from fluidized bed combustion as determined in this study, indicate a potential for utilization. Utilization of the bottom ash could be accepted in certain countries, e.g. France, according to their current limit values. In other countries, e.g. Sweden, no general limit values are given and utilization have to be applied for in each case. The judgement is then based, not only on total contents in the residue and its leaching behaviour, but also on the specific environmental conditions at the site. 7 refs, 17 figs, 12 tabs

  6. Linking Radial Species Segregation and Bubbling Patterns in Gas-Fluidized Beds.

    Science.gov (United States)

    Joseph, Gustavo; Hrenya, Christine; Kozlowski, Joe

    2007-11-01

    Binary mixtures of gas-fluidized Geldart Group B particles with size and/or density differences were experimentally investigated at gas velocities up to 3 times the complete fluidization velocities (ufc) of the mixtures. Steady state operation of the bed was ensured prior to data collection. Local bubbling information (mean bubble size, bubble rise velocity, and bubbling frequency) was obtained throughout the bed by means of a backscattered-light optical probe. Segregation data were obtained via bed ``freezing'' and subsequent sieving of layers. Monodisperse runs were also performed as benchmarks for the binary-mixture runs. Perceptible radial variations in species composition were encountered, with the less massive particles tending toward the bed center in most cases. For systems where the species differed in both size and density, the bottom layer presents a reversal of radial segregation pattern at gas velocities below 2ufc. At velocities below 2ufc, bubbling is seen predominantly at the bed periphery, with qualitative differences between monodisperse and mixed systems above 2ufc. A detailed analysis of the bubbling patterns at the various compositions and gas velocities is presented, and links to the observed segregation behavior are made.

  7. Development of a fluidized bed system for adsorption of phenol from aqueous solutions with commercial macroporous resins

    Directory of Open Access Journals (Sweden)

    R. A. Corrêa

    2007-03-01

    Full Text Available This work is related to removal of phenol from wastewaters by adsorption onto polymeric resins, a current alternative to activated carbon. A closed circuit, bench-scale liquid fluidized bed system was developed for this purpose. Phenol aqueous solutions with initial concentrations in the range of 0.084 to 0.451 kg/m³ were used to fluidize small permeable capsules of stainless steel screen containing a commercial resin at 308 K. Experiments were carried out using a fluidizing velocity 20% above that of the minimum fluidization of the capsules. Typically, 30 passages of the liquid volume circulating through the bed were required to reach a quasi-equilibrium concentration of phenol in the treated effluent. A simple batch adsorption model using the Freundlich isotherm successfully predicted final phenol concentrations. Suspended solids, often present in residual waters and a common cause of fixed bed clogging, were simulated with wood sawdust.

  8. Innovative method using magnetic particle tracking to measure solids circulation in a spouted fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Patterson, Ms. Emily [Waynesburg University; Halow, John [Waynesburg University; Daw, C Stuart [ORNL

    2009-01-01

    We describe an innovative method for measuring particle motion inside spouted fluidized beds. The method uses a magnetic tracer particle, which follows the bulk particle flow and is continuously tracked by multiple magnetic field detectors located outside the bed. We analyze signals from the detectors to determine the tracer position at each instant in time. From statistical analysis of the tracer trajectory, characteristic measures of the bulk particle flow, such as the average recirculation frequency, can be determined as a function of operating conditions. For experiments with a range of particle sizes and densities in a 3.9-cm-diameter spouted bed, we find that average solids recirculation rates correlate with excess velocity (superficial minus minimum spouting velocity), particle density, and bed depth.

  9. Thermal energy storage systems using fluidized bed heat exchangers

    Science.gov (United States)

    Weast, T.; Shannon, L.

    1980-01-01

    A rotary cement kiln and an electric arc furnace were chosen for evaluation to determine the applicability of a fluid bed heat exchanger (FBHX) for thermal energy storage (TES). Multistage shallow bed FBHX's operating with high temperature differences were identified as the most suitable for TES applications. Analysis of the two selected conceptual systems included establishing a plant process flow configuration, an operational scenario, a preliminary FBHX/TES design, and parametric analysis. A computer model was developed to determine the effects of the number of stages, gas temperatures, gas flows, bed materials, charge and discharge time, and parasitic power required for operation. The maximum national energy conservation potential of the cement plant application with TES is 15.4 million barrels of oil or 3.9 million tons of coal per year. For the electric arc furnance application the maximum national conservation potential with TES is 4.5 million barrels of oil or 1.1 million tons of coal per year. Present time of day utility rates are near the breakeven point required for the TES system. Escalation of on-peak energy due to critical fuel shortages could make the FBHX/TES applications economically attractive in the future.

  10. Tandem fluidized bed elutriator-Pneumatic classification of coal particles in a fluidized conveyer

    Institute of Scientific and Technical Information of China (English)

    Zhouen Liu; Yimin Xie; Yin Wang; Jian Yu; Shiqiu Gao; Guangwen Xu

    2012-01-01

    Coal moisture control (CMC) in coking process,which reduces coal moisture before loading the coal into the coke oven,allows substantial reduction in coking energy consumption and increase in coke productivity.The technology is seeking to integrate the coal classification,thus calling it the coal classifying moisture control (CCMC),to separate the fine and coarse coal fractions in the CMC process so that the downstream coal crushing can only treat the coarse fraction.CCMC adopts a reactor that integrates a fiuidized bottom section and a pneumatic conveying top section.The present work investigates the pneumatic classification behavior in a laboratory CCMC reactor with such a configuration by removing the coal fraction below a given size (e.g.,3.0 mm) from a 0 to 20,0 mm coal feed.The results show that the coal classification were dominated by the gas velocity in the top conveying section,and the required gas velocity for ensuring the maximal degree of removing a fine coal fraction could be roughly predicted by the Richardson and Zaki equation.The effect of bottom fluidization on the performance of CCMC is also examined.

  11. Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

    Energy Technology Data Exchange (ETDEWEB)

    Jonassen, Ola

    1999-10-01

    The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidising gas, (3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger, and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

  12. Chaos Transfer in Fluidized Beds Accompanied with Biomass Pyrolysis

    Institute of Scientific and Technical Information of China (English)

    唐松涛; 李定凯; 吕子安; 沈幼庭

    2003-01-01

    Experiments of biomass pyrolysis were carried out in a fiuidized bed, and dynamic signals of pressure and temperature were recorded. Correlation dimension was employed to characterize the chaotic behavior of pressure and temperature signals. Both pressure and temperature signals exhibit chaotic behavior, and the chaotic behavior of temperature signals is always weaker than that of pressure signals. Chaos transfer theory was advanced to explain the above phenomena. The discussion on the algorithm of the correlation dimension shows that the distance definition based on rhombic neighborhood is a better choice than the traditional one based on spherical neighborhood. The former provides a satisfactory result in a much shorter time.

  13. TREATMENT OF POME BY PILOT PLANT ANAEROBIC FLUIDISED BED REACTOR

    OpenAIRE

    Abdullah Al-Mamun; Azni Idris

    2010-01-01

    A pilot scale anaerobic fluidised bed reactor (AnFBR) of 2000 L capacity was studied to determine its performance to treat palm oil mill effluent (POME). The pilot plant was operated at ambient temperature with diluted POME as substrate. It took 17 days for the start-up of the reactor with pre-seeded sand media. The AnFBR was capable to remove a large portion of organics at relatively shorter retention time. Maximum and minimum COD removal efficiency of 85% and 65% were attained at a ...

  14. Energetic, ecologic and fluid-dynamic analysis of a fluidized bed gasifier operating with sugar cane bagasse

    International Nuclear Information System (INIS)

    This work aims to study the thermodynamic, ecological and fluid-dynamic aspects of a circulating fluidized bed gasifier using sugar cane bagasse as biomass, in order to estimate a model of its normal operation. In the initial stage was analysed the composition of biomass selected (sugar cane bagasse) and its lower heating value (LHV) was calculated. The energy balance of the gasifier was done, being the volumetric flow of air, synthesis gas and biomass estimated. Also the power produced by this gasifier was theoretically estimated. Then the circulating fluidized bed gasifier was designed for operation with approximately 100 kg/h of processed biomass. Cross-sectional area of the reactor, feeder size, diameter of the exit zone of the gases and minimum height of the expanded bed were selected. Some bed gasifier hydrodynamic factors were also studied. The minimum fluidization velocity, fluidization terminal velocity, and average fluidizing velocity were calculated, in order to understand the fluid-dynamic behaviour of gasification of this fuel. It was obtained a theoretical model that can support a possible prototype of circulating fluidized bed gasifier biomass. Finally, there were studied the ecological aspects of the gasifier, through an overall methodology. Ecological efficiencies were estimated for two scenarios: first considering the carbon cycle and thereafter disregarding the carbon cycle. In both cases, it can be proved the ecological viability of the project. -- Highlights: • we develop a methodology to size a fluidized bed gasifier. • we validate this methodology comparing to a fixed bed gasifier values. • we aggregate ecological efficiency to this methodology

  15. Assembly-Controlled Permeability of Layer-by-Layer Polymeric Microcapsules Using a Tapered Fluidized Bed.

    Science.gov (United States)

    Noi, Ka Fung; Roozmand, Ali; Björnmalm, Mattias; Richardson, Joseph J; Franks, George V; Caruso, Frank

    2015-12-23

    Nano- and microcapsules engineered through layer-by-layer (LbL) assembly are finding an increasingly large number of applications as catalysts, electrochemical biosensors, bioreactors, artificial cells and drug delivery vehicles. While centrifugation-based LbL assembly is the most common method for coating template particles and preparing capsules, it is a batch process and requires frequent intervention that renders the system challenging to automate and scale up. Here, we report the use of a tapered fluidized bed (TFB) for the preparation of multilayered polymer capsules. This is a significant improvement over our recent approach of fluidizing particles in cylindrical fluidized beds (CFB) for LbL assembly. We demonstrate that TFB is compatible with particles TFB LbL assembly were investigated. The obtained TFB microcapsules demonstrate increased film thickness and roughness compared with those prepared using centrifugation-based LbL assembly. Furthermore, PMASH microcapsules exhibit lower swelling and permeability when prepared via TFB LbL assembly compared with centrifugation-based LbL assembly due to enhanced multilayer deposition, entanglement, and cross-linking. Therefore, polymeric capsules fabricated via TFB LbL assembly may be useful for encapsulation and retention of relatively low molecular weight (∼20 kDa) hydrophilic biomacromolecules to passively or responsively release the payload for drug delivery applications. PMID:26651354

  16. Particle Measurement Sensor for in situ determination of phase structure of fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Qiang Zhang; Cang Huang; Dong Jiang; Xiaobo We; Zhen Qian; Fei Wei

    2009-01-01

    Based on three-dimensional (3D) acceleration sensing, an intelligent particle spy capable of detecting, transferring, and storing data, is proposed under the name of Particle Measurement Sensor (PMS). A prototype 60-mm-dia PMS was tested to track its freefall in terms of velocity and displacement, and served as a particle spy in a fluidized bed delivering the in situ acceleration information it detects. With increasing superficial gas velocity in the fluidized bed, the acceleration felt by PMS was observed to increase. The variance of the signals, which reflect the fluctuation, increased at first, reaching a maximum at the gas velocity (Uc) which marks the transition from bubbling to turbulent fluidization. Through probability density distribution (PDD) analysis, the PDD peak can be divided into the emulsion phase peak and the bubble phase peak. The average acceleration of emulsion and bubble phase increased, while the variance of both phases reached a maximum at Oc, at the same time. However, the difference between the variances of two phases reached the maximum at Oc. Findings of this study indicate that PMS can record independent in situ information. Further, it can provide other in situ measurements when equipped with additional multi-functional sensors.

  17. An Experimental and Numerical Investigation of Fluidized Bed Gasification of Solid Waste

    Directory of Open Access Journals (Sweden)

    Sharmina Begum

    2013-12-01

    Full Text Available Gasification is a thermo-chemical process to convert carbon-based products such as biomass and coal into a gas mixture known as synthetic gas or syngas. Various types of gasification methods exist, and fluidized bed gasification is one of them which is considered more efficient than others as fuel is fluidized in oxygen, steam or air. This paper presents an experimental and numerical investigation of fluidized bed gasification of solid waste (SW (wood. The experimental measurement of syngas composition was done using a pilot scale gasifier. A numerical model was developed using Advanced System for Process ENgineering (Aspen Plus software. Several Aspen Plus reactor blocks were used along with user defined FORTRAN and Excel code. The model was validated with experimental results. The study found very similar performance between simulation and experimental results, with a maximum variation of 3%. The validated model was used to study the effect of air-fuel and steam-fuel ratio on syngas composition. The model will be useful to predict the various operating parameters of a pilot scale SW gasification plant, such as temperature, pressure, air-fuel ratio and steam-fuel ratio. Therefore, the model can assist researchers, professionals and industries to identify optimized conditions for SW gasification.

  18. Research on coal staged conversion poly-generation system based on fluidized bed

    Institute of Scientific and Technical Information of China (English)

    Mingjiang Ni; Chao Li; Mengxiang Fang; Qinhui Wang; Zhongyang Luo; Kefa Cen

    2014-01-01

    A new coal staged conversion poly-generation system combined coal combustion and pyrolysis has been developed for clean and high efficient utilization of coal. Coal is the first pyrolysed in a fluidized pyrolyzer. The pyrolysis gas is then purified and used for chemical product or liquid fuel production. Tar is collected during purification and can be processed to extract high value product and to make liquid fuels by hydro-refining. Semi-coke from the pyrolysis reactor is burned in a circulating fluidized bed (CFB) combustor for heat or power generation. The system can realize coal multi-product generation and has a great potential to increase coal utilization value. A 1 MW poly-generation system pilot plant and a 12 MW CFB gas, tar, heat and power poly-generation system was erected. The experimental study focused on the two fluidized bed operation and characterization of gas, tar and char yields and compositions. The results showed that the system could operate stable, and produce about 0.12 m3/kg gas with 22 MJ/m3 heating value and about 10 wt%tar when using Huainan bituminous coal under pyrolysis temperature between 500 and 600 ?C. The produced gases were mainly H2, CH4, CO, CO2, C2H4, C2H6, C3H6 and C3H8. The CFB combustor can burn semi-coke steadily. The application prospect of the new system was discussed.

  19. A Study of Vertical Gas Jets in a Bubbling Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Ceccio, Steven [Univ. of Michigan, Ann Arbor, MI (United States); Curtis, Jennifer [Univ. of Florida, Gainesville, FL (United States)

    2011-04-15

    A detailed experimental study of a vertical gas jet impinging a fluidized bed of particles has been conducted with the help of Laser Doppler Velocimetry measurements. Mean and fluctuating velocity profiles of the two phases have been presented and analyzed for different fluidization states of the emulsion. The results of this work would be greatly helpful in understanding the complex two-phase mixing phenomenon that occurs in bubbling beds, such as in coal and biomass gasification, and also in building more fundamental gas-solid Eulerian/Lagrangian models which can be incorporated into existing CFD codes. Relevant simulations to supplement the experimental findings have also been conducted using the Department of Energy's open source code MFIX. The goal of these simulations was two-fold. One was to check the two-dimensional nature of the experimental results. The other was an attempt to improve the existing dense phase Eulerian framework through validation with the experimental results. In particular the sensitivity of existing frictional models in predicting the flow was investigated. The simulation results provide insight on wall-bounded turbulent jets and the effect frictional models have on gas-solid bubbling flows. Additionally, some empirical minimum fluidization correlations were validated for non-spherical particles with the idea of extending the present study to non-spherical particles which are more common in industries.

  20. Drying of suspension and pastes in fluidized bed of inert particles

    Directory of Open Access Journals (Sweden)

    ZORANA LJ. ARSENIJEVIC

    2000-12-01

    Full Text Available A fluid bed dryer with inert particles was used for the drying of suspensions and pastes. The effects of the operating conditions on the dryer throughput and on the product quality were investigated. Experiments were performed in a cylindrical column 215 mm in diameter and 1200 mm in height with 0.925 mm diameter glass spheres as the fluidizing media. Cineb fungicide, copper hydroxide and pure water were used as the feed material. With respect to the main efficiency criteria, i.e., specific water evaporation rate, specific heat consumption and specific air consumption, a fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies. A high drying efficiency results from the large contact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles, due to aggregative fluidization and mechanical agitation, leads to nearly isothermal conditions throughout the bed. In our experiments, suspensions and very dense pastes were successfully treated. Suspension and product hold-up in the bed varies between 6 and 8 % by mass and a product with the same particle size as the raw material is obtained.

  1. Performance of a pilot-scale, steam-blown, pressurized fluidized bed biomass gasifier

    Science.gov (United States)

    Sweeney, Daniel Joseph

    With the discovery of vast fossil resources, and the subsequent development of the fossil fuel and petrochemical industry, the role of biomass-based products has declined. However, concerns about the finite and decreasing amount of fossil and mineral resources, in addition to health and climate impacts of fossil resource use, have elevated interest in innovative methods for converting renewable biomass resources into products that fit our modern lifestyle. Thermal conversion through gasification is an appealing method for utilizing biomass due to its operability using a wide variety of feedstocks at a wide range of scales, the product has a variety of uses (e.g., transportation fuel production, electricity production, chemicals synthesis), and in many cases, results in significantly lower greenhouse gas emissions. In spite of the advantages of gasification, several technical hurdles have hindered its commercial development. A number of studies have focused on laboratory-scale and atmospheric biomass gasification. However, few studies have reported on pilot-scale, woody biomass gasification under pressurized conditions. The purpose of this research is an assessment of the performance of a pilot-scale, steam-blown, pressurized fluidized bed biomass gasifier. The 200 kWth fluidized bed gasifier is capable of operation using solid feedstocks at feedrates up to 65 lb/hr, bed temperatures up to 1600°F, and pressures up to 8 atm. Gasifier performance was assessed under various temperatures, pressure, and feedstock (untreated woody biomass, dark and medium torrefied biomass) conditions by measuring product gas yield and composition, residue (e.g., tar and char) production, and mass and energy conversion efficiencies. Elevated temperature and pressure, and feedstock pretreatment were shown to have a significant influence on gasifier operability, tar production, carbon conversion, and process efficiency. High-pressure and temperature gasification of dark torrefied biomass

  2. Anaerobic treatment of wastewater containing methanol in upflow anaerobic sludge bed (UASB) reactor

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The direct conversion of methanol into methane is the main process in anaerobic treatment of methanol containing wastewater.However,acetic acid can also be produced from methanol theoretically,which may probably result in an abrupt pH drop and deteriorate the anaerobic process.Therefore,it is interesting to know what would really happen in an anaerobic reactor treating methanol wastewater.In this study,an up-flow anaerobic sludge bed (UASB) reactor treating methanol wastewater was operated.The chemical oxygen demand (COD),acetic acid and pH of the effluent were monitored at different loadings and influent alkalinity.The results showed that the anaerobic reactor could be operated steadily at as low as 119 mg/L of influent alkalinity and high organic loading rate with no obvious pH drops.Volatile fatty acids accumulation was not observed even at strong shock loadings.The microorganisms in the sludge at the end of the test became homogeneous in morphology,which were mainly spherical or spheroidal in shape.

  3. Separation of harmful impurities from refuse derived fuels (RDF) by a fluidized bed.

    Science.gov (United States)

    Krüger, B; Mrotzek, A; Wirtz, S

    2014-02-01

    In firing systems of cement production plants and coal-fired power plants, regular fossil fuels are increasingly substituted by alternative fuels. Rising energy prices and ambitious CO2-reduction goals promote the use of alternative fuels as a significant contribution to efficient energy recovery. One possibility to protect energy resources are refuse-derived fuels (RDF), which are produced during the treatment of municipal solid, commercial and industrial waste. The waste fractions suitable for RDF have a high calorific value and are often not suitable for material recycling. With current treatment processes, RDF still contains components which impede the utilization in firing systems or limit the degree of substitution. The content of these undesired components may amount to 4 wt%. These, in most cases incombustible particles which consist of mineral, ceramic and metallic materials can cause damages in the conveying systems (e. g. rotary feeder) or result in contaminations of the products (e. g. cement, chalk). Up-to-date separation processes (sieve machine, magnet separator or air classifier) have individual weaknesses that could hamper a secure separation of these particles. This article describes a new technology for the separation of impurities from refuse derived fuels based on a rotating fluidized bed. In this concept a rotating motion of the particle bed is obtained by the tangential injection of the fluidization gas in a static geometry. The RDF-particles experience a centrifugal force which fluidized the bed radially. The technical principle allows tearing up of particle clusters to single particles. Radially inwards the vertical velocity is much lower thus particles of every description can fall down there. For the subsequent separation of the particles by form and density an additionally cone shaped plate was installed in the centre. Impurities have a higher density and a compact form compared to combustible particles and can be separated with a high

  4. Study of thermal energy storage using fluidized bed heat exchangers

    Science.gov (United States)

    Weast, T. E.; Shannon, L. J.; Ananth, K. P.

    1980-01-01

    The technical and economic feasibility of fluid bed heat exchangers (FBHX) for thermal energy storage (TES) in waste heat recovery applications is assessed by analysis of two selected conceptual systems, the rotary cement kiln and the electric arc furnace. It is shown that the inclusion of TES in the energy recovery system requires that the difference in off-peak and on-peak energy rates be large enough so that the value of the recovered energy exceeds the value of the stored energy by a wide enough margin to offset parasitic power and thermal losses. Escalation of on-peak energy rates due to fuel shortages could make the FBHX/TES applications economically attractive in the future.

  5. Case study applications of venture analysis: fluidized bed. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Mosle, R.

    1978-05-01

    In order to appraise the case for government intervention in the case of atmospheric fluid-bed combustion, Energy Resources Company and Rotan Mosle have developed a methodology containing four key elements. The first is an economic and environmental characterization of the new technology; the second, a survey of its prospective users and vendors; the third, a cost-benefit analysis of its prospective social benefits; and the fourth, an analytical model of its market penetration and the effects thereon of a basket of government incentives. Three major technical obstacles exist to continued AFBC development: feeding coal and limestone reliably to the boiler, tube erosion and corrosion, and developing boiler turndown capability. The review of the economic, environmental and technical attributes of the new technology has suggested that the preliminary venture can be selected with confidence as a commercial prospect capable of detailed evaluation from both private and public perspectives. The venture choice can therefore be considered firm: it will be the equipment required for the combustion of coal in atmospheric fluid beds as applied to industrial process steam in boilers of at least 83 Kpph capacity. The most effective demonstration of the potential of AFBC in the eyes of prospective industrial users is that provided by a project conducted by the private sector with minimal government direction. Unlike the ''experimental'' style of existing mixed public-private demonstration projects, the pressure to achieve reliability in more commercial applications would serve rapidly to reveal more clearly the potential of AFBC. The marketplace can be allowed to decide its fate thereafter. Once AFBC has been successfully demonstrated, the relative merits of AFBC and coal-FGD are best left to prospective users to evaluate.

  6. Mass transfer between a fluid and an immersed object in liquid–solid packed and fluidized beds

    Directory of Open Access Journals (Sweden)

    NEVENKA BOSKOVIC-VRAGOLOVIC

    2005-11-01

    Full Text Available Themass transfer coefficient between fluid and an immersed sphere in liquid packed and fluidized beds of inert spherical particles have been studied experimentally using a column 40 mm in diameter. The mass transfer data were obtained by studying the transfer of benzoic acid from the immersed sphere to flowing water using the dissolution method. In all runs, the mass transfer rates were determined in the presence of inert glass particles 0.50-2.98 mm in diameter. The influence of different parameters, such as: liquid velocity, particles size and bed voidage, on the mass transfer in packed and fluidized beds is presented. The obtained experimental data for mass transfer in the packed and particulate fluidized bed were correlated by a single correlation, thus confirming the similarity between the two systems.

  7. A comparative evaluation of fluidized bed assisted drag finishing and centrifugal disk dry finishing

    Directory of Open Access Journals (Sweden)

    M. Barletta

    2014-06-01

    Full Text Available Drag finishing of brass (Cu-30 wt.% Zn rings using fluidized abrasives, which is a new finishing technology, is comparatively evaluated with centrifugal disk finishing. The comparison was performed by selecting the same abrasive granulates of two different sizes and operating the equipment for the same processing time or at their respective maximum speeds. The experimental analysis investigated the change in workpiece morphology, material removal during finishing and dimensional accuracy. The results showed that each of the types of equipment investigated in the study were capable of a high finishing performance with a relatively short processing time. However, fluidized bed assisted drag finishing was more effective than centrifugal disk finishing in both the achievable quality of the processed parts and reduced processing time. In contrast, centrifugal disk finishing was preferable whenever low erosion and stringent dimensional tolerances were demanded.

  8. STUDY ON HOT SAND COOLING EQUIPMENT WITH DAMPING SAND CASCADE AND VERTICAL SPOUTED-FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    L.C. Wang; F. Wang; X.H. You

    2005-01-01

    A new kind of hot sand cooling equipment with vertical spouted-fluidized bed is developed in this paper. It is similar to the traditional horizontal vibrating fluidized boiling cooler in principle but different from it in structure. The processing principle of the cooler is analyzed. The influence of main structural and processing parameters on the cooling effect and its mechanism are researched. Other characteristics of the cooler are discussed also. Experiment results show that the cooling efficiency η is equal to or larger than 83%, the temperature of output sand is less than 40℃ with the temperature of input sand is about between 80 and 90℃, and the productivity is 5t/(h·m)

  9. Steam reforming of propane in a fluidized bed membrane reactor for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rakib, Mohammad A.; Grace, John R.; Lim, C. Jim; Ghiasi, Bahman [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver BC (Canada); Elnashaie, Said S.E.H. [College of Engineering, Misr University for Science and Technology, Distinguished District, 6th of October Province (Egypt)

    2010-06-15

    Steam reforming of propane was carried out in a fluidized bed membrane reactor to investigate a feedstock other than natural gas for production of pure hydrogen. Close to equilibrium conditions were achieved inside the reactor with fluidized catalyst due to the very fast steam reforming reactions. Use of hydrogen permselective Pd{sub 77}Ag{sub 23} membrane panels to extract pure hydrogen shifted the reaction towards complete conversion of the hydrocarbons, including methane, the key intermediate product. Irreversible propane steam reforming is limited by the reversibility of the steam reforming of this methane. To assess the performance improvement due to pure hydrogen withdrawal, experiments were conducted with one and six membrane panels installed along the height of the reactor. The results indicate that a compact reformer can be achieved for pure hydrogen production for a light hydrocarbon feedstock like propane, at moderate operating temperatures of 475-550 C, with increased hydrogen yield. (author)

  10. An analysis of process heat recovery in a gas-solid shallow fluidized bed

    Directory of Open Access Journals (Sweden)

    A. A. B. Pécora

    2006-12-01

    Full Text Available This work presents an experimental study of a continuous gas-solid fluidized bed with an immersed horizontal tube. Silica sand (254mm diameter was used as solid particles and air was used for fluidization in a 900mm long and 150mm wide heat exchanger. Measurements were made under steady state conditions for a solid particle mass flow rate from 14 to 95kg.h-1 and a number of baffles from 0 to 8. Results showed that the heat transfer coefficient increases with the solid particle mass flow rate and with the number of baffles, suggesting that these are important factors to be considered in the design of such equipment. An empirical correlation for the heat transfer coefficient is proposed as a function of solid particle and gas mass flow rate, number of baffles and gas velocity.

  11. Industrial application of the technique of removing Mo by a combination of moving packed bed and fluidized bed ion exchange

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The application of the technique of removing molybdenum by moving packed bed and fluidized bed ion-exchange in a factory was described. The data showed that the Mo removal efficiency is above 99%, and the Mo content inAFT (Ammonium Paratungstate) is controlled steadily below 18 × 10-6, in the case of treating the feed liquor containing Mo1.4 g/L. The technique is simple and convenient in operation, good reusability of resin, loss consumption of desorption rea-gent and little pollution on environment. The loss of tungsten is less than 0.5%. The technique has been proved to be aneconomical and efficient process for Mo removal.

  12. A Cold Model Experimental Study on the Flow Characterisitcs of Bed Baterial in A Fluidized ed Bottom Ash Cooler in a CFB Boiler

    Institute of Scientific and Technical Information of China (English)

    LuXiaofeng; LiYourong

    2000-01-01

    A cold model experimental study on the flowing characteristics of bed meterial between a fluidized bed ash cooler and a furnace of CFB boiler were discussed in this paper.The research results showed that flowing status of the bed material in a bubbling bed,which was run with a circulating fluidized bed together in parallel operation,was influenced by the pressure difference between the CFB and the bubbling bed,the switch status of unlocking air ,and the structure of the exit of the bubbling bed.There was a circulating flow of bed material between CFB and bubbling bed.

  13. Extracting Oxygen from Lunar Simulant Using a Transparent Furnace Pulsed Fluidized Bed

    Science.gov (United States)

    Oryshchyn, L.; Paz, A.; Lee, K.; Reddington, M.

    2010-01-01

    In the event that humans return to the moon, utilizing the local materials will be beneficial for extended stays. Rather than transporting resources, such as oxygen, from Earth, NASA is investigating methods of extracting it from lunar regolith. One promising process is hydrogen reduction. In the hydrogen reduction process, lunar regolith is heated to 1000 C in the presence of hydrogen. The iron oxide (Fe-O) bonds, found in lunar material, are broken and the hydrogen attracts the oxygen to produce water vapor [Allen et al., 1996]. FeO + H2 (right arrow) Fe +H2O. The water vapor is then captured, cleaned, and electrolyzed. The hydrogen is recycled back to the reduction process and the oxygen is stored until consumed by an end user (propulsion, life support, etc.). To obtain a good oxygen yield, the majority of lunar regolith must be exposed to the hydrogen gas and have a high rate of heat transfer from heat source to particle. This is achieved with good solids mixing via fluidization or mechanical agitation. In Generation II of the ROxygen program, the ROxygen Team at Johnson Space Center (JSC) investigated the feasibility of gas only pulsed fluidization as the only means to mix synthetic lunar regolith (simulant) at high temperatures. Fluidized beds have been used in industry to effectively process powders for decades. They consist of gas flowing upward through a bed of particles. The stirring action continuously moves the grains around to achieve uniform mixing of gas, solids, and heat [Geldart, 1986]. A transparent furnace unit was developed by Thoughventions Unlimited LLC (TvU) to aid in the qualitative observation of the fluidization behavior at high temperatures. Multipoint thermocouples and pressure sensors provided quantitative information regarding the quality of mixing. The water produced was measured using humidity sensors and captured using a NASA designed and built condenser. Once the simulant was processed, pneumatically transporting the 'hot' simulant

  14. NUMERICAL PREDICTION OF PARTICLE MIXING BEHAVIOR IN A BUBBLING FLUIDIZED BED

    Institute of Scientific and Technical Information of China (English)

    WU Chun-liang; ZHAN Jie-min

    2007-01-01

    In this article the hard-sphere Discrete Particle Model (DPM) is used to study the mixing behavior of particles in the 2-D fluidized bed. Different flow patterns in the bed for two kinds of inlet configurations, namely free bubbling and jet bubbling mode, are captured by the numerical model, under specific superficial gas velocities. To examine the degree of particle mixing, the Fan index is applied. The numerical results show that the rate of particle mixing is larger in the jet bubbling than that in the free bubbling mode. The gross circulations of particles in the jet bubbling bed give a higher degree of mixing because of the involvement of a greater number of particles.

  15. Predicting the energy consumption of continuous well-mixed fluidized bed dryers from drying kinetic data

    Energy Technology Data Exchange (ETDEWEB)

    Baker, C.G.J.

    1999-09-01

    Precious work has shown that it is possible to predict the size of a continuous well-mixed fluidized bed dryer from batch drying curve measurements. This approach has been extended in the present study to include energy consumption calculations. A computer code was written to simulate the performance of the dryer and to determine its specific energy consumption E{sub s}. Starting in this case with an isothermal bed batch drying curve, the program first calculates the mean solids residence time required under specified operating conditions. Mass and energy balances are then used to calculate the heat duty and E{sub s}. The bed temperature was found to have a significant effect on specific energy consumption in all cases. However, the influences of air flowrate and humidity, and of solids loading, were shown to depend on the solids drying characteristics.

  16. Flow Behavior in Z-Path Fluidized-Moving Bed with Inclined Perforated Plate

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The flow behaviors in a gas-solid contactor with inclined perforated plates that form a zigzag path were experimentally studied. In this contactor solid particles slide down along the inclined perforated plates by the upflowing gas. This structure, called as "z-path-moving bed", has some of the advantages of both moving and fluidized beds. The discharge rate of solid particles, inclination angle of the perforated plate, aperture ratio of the perforated plate, size of particles and gas velocity were chosen as parameters for experimental conditions. The stable operation conditions were certained for the particles and apparatus used. The pressure drop, bed height and residence time distribution of particles were measured versus gas velocity.

  17. The formation of impurities in fluidized-bed gasification of biomass, peat and coal; Epaepuhtauksien muodostuminen leijukerroskaasutuksessa

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Laatikainen-Luntama, J.; Kurkela, M.; Leppaelahti, J.; Koljonen, T.; Oesch, P. [VTT Energy, Espoo (Finland); Alen, R. [Jyvaeskylae Univ. (Finland)

    1996-12-01

    The objective of this three-year-long project was to study the effects of different process parameters and bed materials on the formation of impurities in pressurized fluidized-bed gasification. The main emphasis of the project was focused on the formation of tars and nitrogen compounds in wood, peat and coal gasification. The aims of the research were to find out such operating conditions, where the formation of problematic high-molecular-weight tars can be minimised and to create a better understanding on the fate of fuel nitrogen in fluidized-bed gasifiers. Main part of the research was carried out in a bench-scale pressurised fluidized-bed reactor (ID 30 mm), where the effects of pressure, temperature, gas atmosphere and bed material were studied with different feedstocks. Most of the test series were carried out using the same feedstocks as earlier used in the PDU-scale fluidized-bed gasification tests of VTT (pine wood, pine bark, wheat straw, two peats, Rhenish brown coal, Polish and Illinois No.6 bituminous coals). The effects of operating parameters on the product yields (gas components, tars, char) were first studied under inert nitrogen atmosphere. The conversion of fuel nitrogen into ammonia and HCN were also determined for the different feedstocks over the different operating conditions. These studies showed that ammonia is the main fixed nitrogen compound of fluidized-bed pyrolysis with all the feedstocks studied. The conversions of fuel nitrogen into ammonia and HCN was highest with the high volatile fuels and lowest with the two hard coals. Gas atmosphere had a dramatic effect on the conversion of fuel nitrogen; much higher ammonia yields were determined in real gasification gas atmosphere than in inert pyrolysis carried out in N{sub 2} or Argon atmosphere. In addition to the pressurised fluidized-bed pyrolysis tests, laboratory scale pyrolysis research was carried out in order to compare the pyrolysis behaviour of the different feedstocks

  18. TREATMENT OF POME BY PILOT PLANT ANAEROBIC FLUIDISED BED REACTOR

    Directory of Open Access Journals (Sweden)

    Abdullah Al-Mamun

    2010-09-01

    Full Text Available A pilot scale anaerobic fluidised bed reactor (AnFBR of 2000 L capacity was studied to determine its performance to treat palm oil mill effluent (POME. The pilot plant was operated at ambient temperature with diluted POME as substrate. It took 17 days for the start-up of the reactor with pre-seeded sand media. The AnFBR was capable to remove a large portion of organics at relatively shorter retention time. Maximum and minimum COD removal efficiency of 85% and 65% were attained at a loading rate of 4.0 and 13.8 kgCOD/m3.d. BOD and TSS removal rates varied within the range of 64% - 91% and 68% - 89%, respectively. The AnFBR exhibited low sludge production with lower sludge volume indices (SVI. Maximum and minimum effluent indices for the effluent were 35 mL/g and 11 mL/g, respectively. Low SVI values indicated that, anaerobic fluidised bed reactors generate less sludge with fast settling properties. Promising performance at ambient temperature and for detention time shorter than the present practices supported the possibility of AnFBR to treat POME to meet the new requirement set by the DOE Malaysia.

  19. Comparison of the Effects of Fluidized-Bed and Fixed-Bed Reactors in Microwave-Assisted Catalytic Decomposition of TCE by Hydrogen

    OpenAIRE

    Lili Ren; Jin Zhang

    2012-01-01

    Trichloroethylene (TCE) decomposition by hydrogen with microwave heating under different reaction systems was investigated. The activities of a series of catalysts for microwave-assisted TCE hydrodechlorination were tested through the fixed-bed and the fluidized-bed reactor systems. This study found that the different reaction system is suitable for different catalyst type. And there is an interactive relationship between the catalyst type and the reaction bed type.

  20. Comparison of the Effects of Fluidized-Bed and Fixed-Bed Reactors in Microwave-Assisted Catalytic Decomposition of TCE by Hydrogen

    Directory of Open Access Journals (Sweden)

    Lili Ren

    2012-01-01

    Full Text Available Trichloroethylene (TCE decomposition by hydrogen with microwave heating under different reaction systems was investigated. The activities of a series of catalysts for microwave-assisted TCE hydrodechlorination were tested through the fixed-bed and the fluidized-bed reactor systems. This study found that the different reaction system is suitable for different catalyst type. And there is an interactive relationship between the catalyst type and the reaction bed type.