WorldWideScience

Sample records for aluminium ions

  1. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.;

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics...

  2. Straggling of heavy ions in aluminium

    International Nuclear Information System (INIS)

    An effort has been made to determine the straggling in aluminium of 4He, 16O and 35Cl ions of different energies produced by the tandem Van de Graaff at Harwell. The technique consists of scattering the accelerated and collimated ions in a scattering chamber from a 0.100 mg/cm2 gold foil, allowing the scattered ions to pass through a two aperture collimator, using different aluminium foils over one of the apertures and stopping the two emergent beams in a good quality silicon surface barrier detector the output of which is connected to a 4096 channel analyser. The energy widths obtained in the case of helium ions are in fair agreement with both the Bloch and the recent Tschalar (1968) theory. The measured widths in the case of heavy ions are very large and can be explained only if account is taken of their charge distributions in foils. This study should be useful in ion implantation work. (author)

  3. Uptake of aluminium ion by the liver

    International Nuclear Information System (INIS)

    The specific uptake by the rat liver of 28Al was shown. There was specific uptake of 28Al by liver cell nuclei and DNA. This uptake was blocked by prior treatment with stable aluminium. It is concluded that aluminium enters the liver cell by some specific mechanism and that the reaction of aluminium with DNA inside the hepatocyte nucleus could be a mechanism responsible for the development of aluminium-induced experimental porphyria in the rat

  4. Ion beam analysis of aluminium in thin layers

    Energy Technology Data Exchange (ETDEWEB)

    Healy, M.J.F. E-mail: m.j.f.healy@rmcs.cranfield.ac.uk; Pidduck, A.J.; Dollinger, G.; Gorgens, L.; Bergmaier, A

    2002-05-01

    This work quantifies aluminium in thin surface and near surface layers. In one example, the layer overlies a thin gallium nitride layer on an aluminium oxide substrate and in a second example the aluminium exists just below the surface of an indium arsenide substrate. The technique of non-Rutherford elastic backscattering of protons was used for the samples where aluminum in the layer of interest needed to be resolved from aluminium in the sapphire substrate and the results were corroborated at the Technische Universitaet Muenchen using heavy ion elastic recoil detection analysis. In the second example, where it was unnecessary to isolate the signal of aluminium in the layer of interest (as the substrate contained no aluminium), then the {sup 27}Al(d,p{sub 01}){sup 28} Al nuclear reaction was used. The elastic proton scattering cross section of aluminum was found to vary very rapidly over the energy range of interest.

  5. An ultrafast rechargeable aluminium-ion battery

    Science.gov (United States)

    Lin, Meng-Chang; Gong, Ming; Lu, Bingan; Wu, Yingpeng; Wang, Di-Yan; Guan, Mingyun; Angell, Michael; Chen, Changxin; Yang, Jiang; Hwang, Bing-Joe; Dai, Hongjie

    2015-04-01

    The development of new rechargeable battery systems could fuel various energy applications, from personal electronics to grid storage. Rechargeable aluminium-based batteries offer the possibilities of low cost and low flammability, together with three-electron-redox properties leading to high capacity. However, research efforts over the past 30 years have encountered numerous problems, such as cathode material disintegration, low cell discharge voltage (about 0.55 volts ref. 5), capacitive behaviour without discharge voltage plateaus (1.1-0.2 volts or 1.8-0.8 volts) and insufficient cycle life (less than 100 cycles) with rapid capacity decay (by 26-85 per cent over 100 cycles). Here we present a rechargeable aluminium battery with high-rate capability that uses an aluminium metal anode and a three-dimensional graphitic-foam cathode. The battery operates through the electrochemical deposition and dissolution of aluminium at the anode, and intercalation/de-intercalation of chloroaluminate anions in the graphite, using a non-flammable ionic liquid electrolyte. The cell exhibits well-defined discharge voltage plateaus near 2 volts, a specific capacity of about 70 mA h g-1 and a Coulombic efficiency of approximately 98 per cent. The cathode was found to enable fast anion diffusion and intercalation, affording charging times of around one minute with a current density of ~4,000 mA g-1 (equivalent to ~3,000 W kg-1), and to withstand more than 7,500 cycles without capacity decay.

  6. EPR of Mo3+ ions in lutetium aluminium garnet single crystals

    International Nuclear Information System (INIS)

    The EPR spectra of Mo3+ ions have been investigated in lutetium-aluminium garnet at ν=9.35 GHz and T=77 K. Mo3+ ions have been shown to isomorphically substitute A3+ ions in the octahedron coordination. Due to high splitting in the zero field only one transition -1/2 +1/2 is observed. The constants of the spin-hamiltonian describing the experimental data have been determined, and also the causes of broadening the EPR signal of Mo3+ ions in luteaium-aluminium garnet as compared to yttrium-aluminium garnet have been discussed

  7. Microscopic observation of pattern attack by aggressive ions on finished surface of aluminium alloy sacrificial anode

    International Nuclear Information System (INIS)

    This paper presents the results of a microscopic observation on submerged finished surface of aluminium alloy sacrificial anode. Experimental tests were carried out on polished surface aluminium anode exposed to seawater containing aggressive ions in order to observe of pattern corrosion attack on corroding surface of anode. Results have shown, at least under the present testing condition, that surface of sacrificial anode were attack by an aggressive ion such as chloride along grain boundaries. In addition, results of microanalysis showed that the corrosion products on surface of aluminium alloy have Al, Zn and O element for all sample and within the pit was consists of Al, Zn, O and Cl element. (author)

  8. Ion beam analysis of aluminium ion implanted titanium diboride thin films

    Science.gov (United States)

    Mollica, S.; Sood, D. K.; Evans, P. J.; Dytlewski, N.; Short, K. T.

    2002-05-01

    Titanium diboride is often selected for protective coatings due to its high hardness and wear resistance. However, its possible high temperature applications are limited because it exhibits poor oxidation resistance at elevated temperatures. Through ion beam modification, it was anticipated that a stable oxidation barrier could form via the formation of "metastable phases" not otherwise observed in stoichiometric TiB 2. Titanium diboride films were deposited onto single-crystal Si(1 0 0) substrates using DC magnetron sputtering. MEVVA ion implantation was then performed using an extraction voltage of 40 kV. Selected samples were subjected to post-implantation vacuum annealing prior to oxidation, thus comparing the behaviour of crystalline and amorphous films. Results show that aluminium ion implantation reduces the oxidation rate of DC magnetron sputtered titanium diboride thin films within the experimental temperature range.

  9. Effect of titanium and aluminium ion implantation on the microhardness of silica glass

    International Nuclear Information System (INIS)

    Ion implantation effect on silica glass microhardness in investigated by measuring microhardness. Silica glass is irradiated with titanium and aluminium ions with 50 keV energy and 1x1016-3x1017 cm-2 doses after which it is annealed in the air at 1070 K temperature. Almost a twofold growth of the glass microhardness is detected after irradiation. 17 refs., 1 fig

  10. Determination of lattice orientation in aluminium alloy grains by low energy gallium ion-channelling

    International Nuclear Information System (INIS)

    Polished sections of a fine-grained aluminium, silicon carbide metal matrix composite (MMC) alloy were prepared by sputtering using a low energy gallium ion source and column (FIB). The MMC had been processed by high temperature extrusion. Images of the polished surface were recorded using the ion-induced secondary electron emission. The metal matrix grains were distinguished by gallium ion-channelling contrast from the silicon carbide component. The variation of the contrast from the aluminium grains with tilt angle can be recorded and used to determine lattice orientation with the contrast from the silicon carbide (SiC) component as a reference. This method is rapid and suits site-specific investigations where classical methods of sample preparation fail.

  11. Determination of lattice orientation in aluminium alloy grains by low energy gallium ion-channelling

    Energy Technology Data Exchange (ETDEWEB)

    Silk, Jonathan R. [Aerospace Metal Composites Ltd., RAE Road, Farnborough, GU14 6XE (United Kingdom); Dashwood, Richard J. [WMG, University of Warwick, Coventry, CV4 7AL (United Kingdom); Chater, Richard J., E-mail: r.chater@imperial.ac.u [Department of Materials, Imperial College, London SW7 2AZ (United Kingdom)

    2010-06-15

    Polished sections of a fine-grained aluminium, silicon carbide metal matrix composite (MMC) alloy were prepared by sputtering using a low energy gallium ion source and column (FIB). The MMC had been processed by high temperature extrusion. Images of the polished surface were recorded using the ion-induced secondary electron emission. The metal matrix grains were distinguished by gallium ion-channelling contrast from the silicon carbide component. The variation of the contrast from the aluminium grains with tilt angle can be recorded and used to determine lattice orientation with the contrast from the silicon carbide (SiC) component as a reference. This method is rapid and suits site-specific investigations where classical methods of sample preparation fail.

  12. Aluminium and hydrogen ions inhibit a mechanosensory calcium-selective cation channel

    Science.gov (United States)

    Ding, J. P.; Pickard, B. G.

    1993-01-01

    The tension-dependent activity of mechanosensory calcium-selective cation channels in excised plasmalemmal patches from onion bulb scale epidermis is modulated by pH in the physiologically meaningful range between 4.5 and 7.2. It is rapidly lowered by lowering pH and rapidly raised by raising pH. Channel activity is effectively inhibited by low levels of aluminium ions and activity can be partially restored by washing for a few minutes. We suggest that under normal conditions the sensitivity of the mechanosensory channels to pH of the wall free space plays important roles in regulation of plant activities such as growth. We further suggest that, when levels of acid and aluminium ions in the soil solution are high, they might inhibit similar sensory channels in cells of the root tip, thus contributing critically to the acid soil syndrome.

  13. Ion-plasma deposition of aluminium and beryllium coatings on inner surfaces of hollow cylindrical cathodes

    International Nuclear Information System (INIS)

    Application of metal coatings to inner surfaces of hollow cylindrical products of small diameter is simulated and practically realized by ion-plasma deposition method. In the modes proposed and with the cylinder diameter being 10-20 mm, a uniform coating of aluminium and beryllium is provided for at the length equal to (3-4) d, which has not been possible to be realized previously. 11 refs.; 2 tabs

  14. Structural state and phase composition of titanium surface layers implanted by aluminium ions

    International Nuclear Information System (INIS)

    The elemental, phase composition, morphology and structural state of the ion-alloyed surface layers of titanium implanted by the Al ions have been investigated. It was found out that increase of the Al ions dose led to increasing the ion-alloyed layers thickness. It was established that the fine dispersed equilibrium intermetallic phases Ti3Al, TiAl and the solid solution of aluminium in titanium were formed in the modified layers. The agglomeration of the intermetallide phases occurred above the dose 6.2 x 1017 ion/cm2. The dependence of the structure state and phase composition of the implanted titanium layers on the implantation condition was considered

  15. Titanium and aluminium ions implanted by plasma on polyethylene

    International Nuclear Information System (INIS)

    The ion implantation by plasma of titanium and aluminum on polyethylene thin films (PE) is presented. The results indicate that the polymers reacted firstly with the oxygen and/or nitrogen carrying gases, and later its received the metallic particles that formed thin films. The stainless steel and the titanium formed a single phase. The metallic layers grew in the interval of 1 to 2 nm/min, its are thin, but enough to change the hardness of the polymer that it is increased in more of 20 times. (Author)

  16. Aluminium-induced ion transport in Arabidopsis: the relationship between Al tolerance and root ion flux

    OpenAIRE

    Bose, Jayakumar; Babourina, Olga; Shabala, Sergey; RENGEL, ZED

    2010-01-01

    Aluminium (Al) rhizotoxicity coincides with low pH; however, it is unclear whether plant tolerance to these two factors is controlled by the same mechanism. To address this question, the Al-resistant alr104 mutant, two Al-sensitive mutants (als3 and als5), and wild-type Arabidopsis thaliana were compared in long-term exposure (solution culture) and in short-term exposure experiments (H+ and K+ fluxes, rhizosphere pH, and plasma membrane potential, E m). Based on biomass accumulation, als5 and...

  17. Effect of metal vapour vacuum arc ion implantation of aluminium on sliding wear characteristics of Ti-6Al-4V

    International Nuclear Information System (INIS)

    The metal vapour vacuum arc ion source is introduced and its more important features and system characteristics are described. Specific reference is made to applications in the field of metallurgical surface treatment by metal ion implantation and some recent developments are reviewed. The effects of aluminium ion implantation (doses up to 1.3 x 1017 ions/cm2) on the sliding wear properties of Ti-6Al-4V forms the emphasis of the ensuing investigation. Damage induced in sliding wear tests was reduced by about 50% after aluminium implantation, owing to a higher surface hardness. Several techniques of surface analysis including glancing angle X-ray diffraction and glow discharge optical emission spectroscopy indicated that subsurface precipitates were primarily responsible for the observed wear mechanism. The strengthening of subsurface material delayed the onset of superficial plastic deformation and resulted in enhanced tribological properties. (Author)

  18. Kinetics of fluorescence properties of Eu3+ion in strontium-aluminium-bismuth-borate glasses

    Institute of Scientific and Technical Information of China (English)

    M. Dhamodhara Naidu; D. Rajesh; A. Balakrishna; Y.C. Ratnakaram

    2014-01-01

    Eu3+doped strontium-aluminium-bismuth-borate glasses with the chemical composition (50–x)B2O3+20Bi2O3+7AlF3+8SrO+15SrF2+xEu2O3 (where x=0.1 mol.%, 0.5 mol.%, 1.0 mol.%and 1.5 mol.%) were prepared by the conventional melt quenching technique. Structural properties of the prepared glasses were analysed through X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and Raman spectral techniques. Thermal stability of glass was analysed by differential thermal analysis (DTA) curve. Photoluminescence characteristics were studied using excitation, emission spectra and decay curves of Eu3+doped strontium-aluminium-bismuth-borate glasses. The Judd-Ofelt (J-O) intensity parameters,Ωλ(λ=2, 4 and 6) were obtained using emission spectra and was used to identify the nature of Eu3+ions with their surrounding ligands. Using J-O parameters the tran-sition probabilities (A), stimulated emission cross-sections σEp , branching ratios (βR) and radiative lifetimes (τmeas and τcal) were evaluated for the 5D0→7FJ (J=0, 1, 2, 3 and 4) transition of Eu3+ions in the present glasses. The decay profiles were found to be non exponential for all the concentrations and the measured lifetimes (τmeas) were obtained from the decay profiles. The higher values of A,σEp ,βR and quantum efficiency (η) for 5D0→7F2 emission transition at 617 nm confirmed the present glass was as active medium for red laser emission applications.

  19. Cerium luminescence in borate glass and effect of aluminium on blue green emission of cerium ions

    International Nuclear Information System (INIS)

    CeO2 doped lead borate (CE) and lead alumino borate (CEA) glasses are prepared by melt quench method at high temperature. The main luminescence band of 5d–4f transition of Ce3+ ions with maxima at around 489 nm of Ce3+ ions in these glasses has been observed, along with red shift and larger stokes shift, which shows that the covalency of the rare earth to oxygen bond increases with the increase in CeO2 content at the expense of Al2O3. Shifting of UV absorption edge towards longer wavelength and a decrease in band gap with increase in CeO2 concentration in both the glass systems has been observed. Moreover densification and stabilization of glass network has been observed which is due to conversion of BO3 units to more compact and stable BO4 units. This covalency effect and the formation of BO4 groups with addition of CeO2 and incorporation of Al2O3 content are responsible for clear effect on luminescence of the present glass system. Moreover the optical basicity values were theoretically determined along with density and molar volume. -- Highlights: • Aluminium incorporation assists in dispersing the clusters of cerium ions and thus enhancing luminescence response. • Decrease of optical band gap energy with an increase of cerium concentration shows the semiconducting behavior. • Larger stokes shift shows that the covalency of rare earth to oxygen bond increases with increase in CeO2

  20. Combined Kelvin probe force microscopy and secondary ion mass spectrometry for hydrogen detection in corroded 2024 aluminium alloy

    OpenAIRE

    Larignon, Céline; Alexis, Joël; Andrieu, Eric; Lacroix, Loïc; Odemer, Grégory; Blanc, Christine

    2013-01-01

    The capability of Kelvin probe force microscopy (KFM) to detect and locate hydrogen in corroded 2024 aluminium alloy was demonstrated. Hydrogen was introduced inside the 2024 alloy following a cyclic corrosion test consisting of cycles of immersion in 1 M NaCl solution followed by exposure to air at -20 °C. The combination of scanning electron microscopy, secondary ion mass spectrometry and KFM demonstrated that the grain and subgrain boundaries were preferential pathways for the short-circui...

  1. Aluminium-induced ion transport in Arabidopsis: the relationship between Al tolerance and root ion flux.

    Science.gov (United States)

    Bose, Jayakumar; Babourina, Olga; Shabala, Sergey; Rengel, Zed

    2010-06-01

    Aluminium (Al) rhizotoxicity coincides with low pH; however, it is unclear whether plant tolerance to these two factors is controlled by the same mechanism. To address this question, the Al-resistant alr104 mutant, two Al-sensitive mutants (als3 and als5), and wild-type Arabidopsis thaliana were compared in long-term exposure (solution culture) and in short-term exposure experiments (H(+) and K(+) fluxes, rhizosphere pH, and plasma membrane potential, E(m)). Based on biomass accumulation, als5 and alr104 showed tolerance to low pH, whereas alr104 was tolerant to the combined low-pH/Al treatment. The sensitivity of the als5 and als3 mutants to the Al stress was similar. The Al-induced decrease in H(+) influx at the distal elongation zone (DEZ) and Al-induced H(+) efflux at the mature zone (MZ) were higher in the Al-sensitive mutants (als3 and als5) than in the wild type and the alr104 mutant. Under combined low-pH/Al treatment, alr104 and the wild type had depolarized plasma membranes for the entire 30 min measurement period, whereas in the Al-sensitive mutants (als3 and als5), initial depolarization to around -60 mV became hyperpolarization at -110 mV after 20 min. At the DEZ, the E(m) changes corresponded to the changes in K(+) flux: K(+) efflux was higher in alr104 and the wild type than in the als3 and als5 mutants. In conclusion, Al tolerance in the alr104 mutant correlated with E(m) depolarization, higher K(+) efflux, and higher H(+) influx, which led to a more alkaline rhizosphere under the combined low-pH/Al stress. Low-pH tolerance (als5) was linked to higher H(+) uptake under low-pH stress, which was abolished by Al exposure. PMID:20497972

  2. Synergistic Effect of Azadirachta Indica Extract and Iodide Ions on the Corrosion Inhibition of Aluminium in Acid Media

    International Nuclear Information System (INIS)

    The synergistic action caused by iodide ions on the corrosion inhibition of aluminium (Al) in 0.5 M HCl in the presence of Azadirachta Indica (AZI) plant extract has been investigated using potintiodynamic polarization and impedance techniques. It is found that AZI extract inhibits the corrosion of aluminium in 0.5 M HCl. The inhibition efficiency increases with the increase in AZI extract concentration, until 24% v/v of AZI extract, then Inh.% is decreased with father increase in AZI extract concentration. The adsorption of this extract in the studied concentration is found to obey Frewendlish adsorption isotherm. The addition of iodide ions enhances the inhibition efficiency to a considerable extent. The increase in Inh.% values in presence of fixed concentration of iodide ions indicates that AZI extract forms an insoluble complex at lower AZI extract concentrations by undergoing a joint adsorption. But at higher concentrations of AZI extract, competitive adsorption is found between iodide ions and the formed complex leading to less Inh.%. The Inh.% decreased in presence of iodide ions with AZI extract than in presence of AZI extract alone at all studied iodide concentrations. The synergism parameter S θ is defined and calculated from surface coverage values. This parameter in the case of AZI extract is found to be more than unity, indicating that the enhanced inhibition efficiency caused by the addition of iodide ions

  3. Observation of excited level populations of Li-like aluminium ions in a recombining plasma: role of atomic processes involving doubly excited levels of Be-like ions

    International Nuclear Information System (INIS)

    An aluminium slab target was irradiated by multiple pulses of Nd:glass laser light with the irradiance of 1.5x1012 W cm-2. After the laser irradiation, a laser-produced aluminium plasma was observed in its recombining phase using a spectrometer whose relative sensitivity was calibrated. We measured relative intensities of the resonance series lines and the lines of the 2p2P-nd2D and 2p2P-ns2S series of the Li-like aluminium ions and derived the excited level populations of the upper levels. >From the slope of the population distribution of the high-lying excited levels and the transition from the series lines to the continuum, the electron temperature and the electron density were estimated to be 8 eV and 3.5x1025 m-3. A comparison of the experimental population distribution with a collisional-radiative (CR) model calculation indicates that recombination of the excited Li-like ions through doubly excited levels of the Be-like ions plays an important role in the population kinetics of the Li-like ions. (author)

  4. Fluorometric determination of aluminium (III) and cadmium (II) by solvent extraction of the ternary complex composed of metal ion, 8-hydroxy-5-quinolinesulfonic acid, and methyltrioctylammonium ion

    Energy Technology Data Exchange (ETDEWEB)

    Kondoh, Yukihiro; Kataoka, Masamitsu; Kambara, Tomihito (Hokkaido Univ., Sapporo (Japan). Faculty of Science)

    1982-02-01

    A fluorometric micro determination of aluminium (III) and cadmium (II) using the formation of metal-8-hydroxy-5-quinolinesulfonic acid-capriquat (methyltrioctylammonium) ternary complex is described. These complexes are easily extracted into chloroform phase and the extract emits a strong fluorescence. Spectra of aluminium (III) and cadmium (II) ternary complexes have the excitation maximum at 396 nm and 400 nm, and emission maximum at 501 nm and 524 nm, respectively. Fluorescence intensity of the aluminium (III) and cadmium (II) ternary complexes extracted into chloroform showed the constant and maximum values in the pH range of aqueous phase from 5.3 to 8.5 and 8.1 to 8.5, respectively. The calibration curves for aluminium (III) and cadmium (II) show good proportionality in the concentration range from 0.5 to 5.0 and 1.0 to 50.0 ..mu..g, respectively. The relative standard deviation observed with four measurements was found to be 1.8% for 0.5 ..mu..g of aluminium (III) and 1.1% for 10.0 ..mu..g of cadmium (II). The effect of diverse ions is studied and a 25-fold amount of Cu(II), Ni(II), Fe(II), Fe(III) in weight gave errors, however, the interferences were easily eliminated by the addition of appropriate masking agent. In the determination of cadmium (II), an equal amount of Co(II), Ni(II), Mn(II), Fe(III) and twice amount of Al(III) gave negative errors, however, the interference of Fe(III) and Al(III) were also eliminated as above.

  5. Electrochemical corrosion characteristics of aluminium alloy 6061 T6 in demineralized water containing 0.1 % chloride ion

    International Nuclear Information System (INIS)

    Direct current electrochemical method is one of the techniques has been used to study the corrosion behaviour of metal/ alloy in its environment. This paper attempts to investigate the corrosion behaviour of Al 6061 T6 immersed in Reactor TRIGA Mark II pool water containing about 0.1 % NaCl content. The result shown that the corrosion rate value of the aluminium 6061 T6 increased with the presence of 0.1 % Ion Chloride content in the demineralized water reactor pool as compared to normal demineralized water. This is due to aggressiveness of chloride ion attack to metal surface. Beside corrosion rate analysis, the further tests such as corrosion behaviour diagram, cyclic polarization have been carried and the results have been reported. (Author)

  6. Electrochemical corrosion characteristics of aluminium alloy 6061 T6 in demineralized water containing 0.1 % chloride ion

    International Nuclear Information System (INIS)

    Direct current electrochemical method is one of the techniques has been used to study the corrosion behaviour of metal/alloy in its environment. This paper attempts to investigate the corrosion behaviour of Al 6061 T6 immersed in Reactor TRIGA Mark II pool water containing about 0.1% NaCl content. The result shown that the corrosion rate value of the aluminium 6061 T6 increased with the presence of 0.1 % Ion Chloride content in the demineralized water reactor pool as compared to normal demineralized water. This is due to aggressiveness of chloride ion attack to metal surface. Beside corrosion rate analysis, the further tests such as corrosion behaviour diagram, cyclic polarization have been carried and the results have been reported. (author)

  7. Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: Comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution

    OpenAIRE

    Stojković Aleksandra; Tajber Lidia; Paluch Krzysztof J.; Djurić Zorica; Parojčić Jelena; Corrigan Owen I.

    2014-01-01

    Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution ...

  8. Friction and wear of stainless steel, titanium and aluminium with various surface treatments, ion implantation and overlay hard coatings

    International Nuclear Information System (INIS)

    This paper deals with the evaluation of the wear properties of 304 stainless steel, commercial grade titanium and commercial grade aluminium without and with different surface treatments, i.e., ion implantation of boron and nitrogen, and overlay coating of superhard materials, titanium carbide and nitride by the Biased Activated Reactive Evaporation (BARE) process. Wear properties were evaluated in adhesive, erosive and abrasive modes of wear. In the case of adhesive wear, ion implantation resulted in an improved wear behaviour in lubricated conditions but had no beneficial effect in dry wear conditions. Overlay coatings on the other hand resulted in improved wear behaviour for both the dry and lubricating conditions. In the case of erosive wear with SiC particles at high velocities, overlay coatings showed higher erosion rates (typical of brittle materials in normal impingement) whereas ion implanted materials behaved similarly as untreated materials; i.e., a lower wear rate than the specimens with overlay coatings. In the case of abrasive wear, it was again observed that the wear rates of overlay coatings is far lower than the wear rates of untreated or ion implanted materials. (author)

  9. Electrochemical co-reduction between aluminium and lanthanide ions in fluoride salts: application to nuclear wastes pyrochemical treatment

    International Nuclear Information System (INIS)

    Nuclear reaction produces fission products such as lanthanides; these neutro-phage elements represent a poison for the nuclear chain reaction and have to be extracted. This thesis concerns lanthanides extraction (neodymium, cerium and samarium) by electrodeposition in the LiF-CaF2 eutectic mixture at 840 C. The process used is an alloy formation with aluminium by electrochemical co-reduction on an inert tungsten electrode. This technique is based on the simultaneous reduction of Al(III) and Ln(III) ions to obtain an alloy at the cathode. A decrease of the lanthanide activity in the alloy is obtained due to Al-Ln formation and a shift of lanthanide reduction potential to more positive values is observed: the theoretical extraction efficiency is then approaching 100 %. When both Ln(III) and Al(III) ions are present in the molten salt, new reduction waves appear between Al and Ln pure metal depositions and are attributed to Al-Ln alloy formation by co-reduction. The alloy compositions have been characterised in function of electrolysis potential: the more the electrolysis potential is negative, higher is the Ln content in the alloy. Finally, extractions by potentiostatic electrolyses have been carried out and the extraction efficiencies for the different lanthanides are higher than 99.4 %. (author)

  10. Fluoride ions sorption of the water using natural and modified hematite with aluminium hydroxide

    International Nuclear Information System (INIS)

    Fluorine is a mineral known for its dental benefits, but fluoride ions can cause fluoro sis in excessive quantities. There are many epidemiological studies on possible adverse effects resulting from prolonged ingestion of fluoride through drinking water. These studies demonstrate that fluoride mainly affects the bone tissue (bones and teeth), may produce an adverse effect on tooth enamel and can cause mild dental fluoro sis at concentrations from 0.9 to 1.2 mg/L in drinking water. In several states of Mexico, water contaminated with fluoride ions can be found, such as Aguascalientes, Chihuahua, Coahuila, Durango, Guanajuato, Sonora, Zacatecas, San Luis Potosi and Jalisco, where the fluoride ions levels are higher than 1.5 mg/L, established by the Mexican Official Standard (NOM-127-Ssa-2000) which sets the permissible limits of water for human use and consumption. Currently, several technologies have been proposed to remove fluoride ions from water such as precipitation methods which are based on the addition of chemicals to water and sorption methods to removed fluoride ions by sorption or ion exchange reactions by some suitable substrate capable of regenerate and reuse. In this work, the sorption of fluoride ions using unmodified and modified hematite with aluminum hydroxide to remove fluoride ions from water by bath experiments was studied. The hematite was modified by treating it with aluminum hydroxide, NaOH and Al2(SO4)3 solutions. The characterization of hematite before and after modification with aluminum hydroxide was studied by X-ray diffraction, scanning electron microscopy, EDS and Bet. The effect of ph, contact time, concentration of fluoride ions, and the dose of sorbent on the sorption of fluoride ions by the modified hematite were studied. Equilibrium was reached within 48 hours of contact time and the maximum sorption of fluoride ions were in the range pHeq between 2.3 and 6.2. Sorption capacities of fluoride ions as a function of dose of sorbent

  11. Ion exchange reactions in amorphous and crystalline aluminium silicates from solution of cerium salts

    International Nuclear Information System (INIS)

    Reactions of ion-exchange of Na+ by Ce3+ and NH4+ on the zeolite containing catalyst, amorphous silica alumina and zeolite Y have been studied. The cerium cations are shown to be exchanged by the Na+ cations with more selectivity than the anmonia cations. In the case of the zeolite containing catalyst and amorphous silica alumina the region of the staggered ion-exchange from the mixture of the solutions of cerium and ammonium sulphates was been detected. This is explained by the formation fo cerium complexes with the sulphate ions

  12. The temperature and dose dependency of helium reemission ratio from helium-ion-implanted aluminium samples

    International Nuclear Information System (INIS)

    It has been observed that blisters and flakes appear on a metal surface implanted He ions above a specific ion dose called the critical dose. At the appearance of the blister and flake, He gas responsible for them is released. There are many reports on the gas reemission with these deformations but there are few reports about it below the critical dose. In this report, temperature and dose dependencies of He reemission from He-ion-implanted Al samples have been studied. After He ions of 20 keV are implanted in Al samples, the samples are heated in vacuum at 400, 450, 475, and 500 deg C with holding time of 0.5, 1, and 2 hours. The numbers of He atoms remaining in the sample are measured by a He atom measurement system. The reemission ratios of the samples prepared at the given temperature and holding time have been obtained from comparison of the numbers of He ions implanted in the samples with the numbers of He atoms measured by the He atom measurement system. The reemission ratio rises with increasing temperature and holding time, and achieved at ∼ 90 % with 500 deg C and 2 hours holding time. On dose dependency of the reemission ratio, it is constant up to 7 x 1014 He atoms and it increases rapidly above it. (author)

  13. Velocities of the excited atoms sputtered at the ion bombardment of lithium and aluminium

    International Nuclear Information System (INIS)

    The Dopler contours of spectral lines of atoms sputtered at a normal incodence of 4-10 keV K+ ion beams on the Li and Al targets are measured by means of Fabry-Perot interferometer. An explicit form of the dependence of the probability of the Al atoms excitation to the resonance level on the rate is found. It is established that the characteristic velocities of the excited atoms are close to a most probable velocities of one-charge secondary ions and are increased with growing excitation energy. The kinetic energy of primary ions does not practically affect the velocity distribution of the excited atoms. Said results are explained in terms of a break-away mechanism of io-photon emission. It is also shown that an increase of the yield of the excited atoms in the presence of oxygen on the target surface is not related with suppression of the processes of the non-radiation deexcitation

  14. Phase transformation in aluminium induced by nickel ion implantation at high energies

    International Nuclear Information System (INIS)

    Implantation of Ni into a pure Al target leads to the formation of amorphous zones. Their formation is studied by transmission electron microscopy (TEM). The present results were obtained in samples implanted with ions having energies between 22 and 40 MeV and fluences between 1.68x1015 and 2.5x1017 ions/cm2. In order to observe the profile of the ion implantation in the TEM, cross-sectional samples were thinned with a specially modified ion bombardment. Measurements of the atomic concentration have been carried out with energy dispersive spectroscopy (EDS). In spite of the Ni concentration (up to 3 at.%) in the implanted layer, there is no observable nuclei of the Al3Ni phase after implantation at 120 K and room temperature. In contrary, amorphous zones with a diameter of about 10 nm are present together with a high density of dislocation loops and dislocations. The Ni concentration in the amorphous zones is about 25 at.%. An implantation conducted at 520 K shows only crystalline precipitates of Al3Ni. We conclude that the Ni implanted in Al agglomerates in zones having composition identical to that of the Al3Ni phase. (orig.)

  15. The effect of copper ions, aluminium ions and their mixtures on separation of pectin from the sugar beet juice

    Directory of Open Access Journals (Sweden)

    Kuljanin Tatjana A.

    2013-01-01

    Full Text Available In sugar industry there is a problem of the presence of undesirable macromolecules compounds such as pectin in sugar beet juice. The affinity of calcium ions commonly used in the sugar industry for the removal of pectin from the sugar beet juice is relatively small. Coagulation and precipitation of pectin can be performed by process of discharging that is chemically induced. Compounds with di- and trivalent cations such as pure CuSO4, Al2(SO43 or their mixtures can be applied for clarification of pectin colloidal systems. According to data from the order of pectin selectivity to divalent metal ions, Cu2+ ions are the first order of ion binding. Also, aluminum sulfate is commonly used in the waste water treatment. Two model solutions of pectin whose concentration corresponds to the concentration of these macromolecules in sugar beet juice (0.1% w/w are investigated. Using a method of measuring zeta potential, it was proven for both investigated pectin that fewer quantities of Cu2+ ions compared to the values of Al3+ ions are needed to reach zero zeta potential. In all the investigated coagulants and their mixtures, zeta potential has changed the sign. In experiments with mixtures has been shown that pure salts showed better coagulation properties. The reduced strength of binding of cations in the case of most of the applied mixture of Cu2+ and Al3+ ions, can be explained by the mutual competition of these ions for the adsorption site (COO- groups on the surface of macromolecules. Mixture with approximately equal shares of ions Cu2+ and Al3+ had the most unfavorable coagulation ability (ion antagonism. Mechanism of discharge as well as the model of double electric layer surrounding pectin macromolecules in the presence of mixtures of Cu2+ and Al3+ ions are suggested. However, due to possible undesirable effects of CuSO4 on food processing, Al2(SO43 is proposed instead of traditional coagulant CaO, not only because of lower consumptions of

  16. A new ion-selective electrode based on aluminium tungstate for Fe(III) determination in rock sample, pharmaceutical sample and water sample

    Indian Academy of Sciences (India)

    Mu Naushad

    2008-12-01

    An inorganic cation exchanger, aluminum tungstate (AT), has been synthesized by adding 0.1 M sodium tungstate gradually into 0.1 M aluminium nitrate at pH 1.2 with continuous stirring. The ion exchange capacity for Na+ ion and distribution coefficients of various metal ions was determined on the column of aluminium tungstate. The distribution studies of various metal ions showed the selectivity of Fe(III) ions by this cation exchange material. So, a Fe(III) ion-selective membrane electrode was prepared by using this cation exchange material as an electroactive material. The effect of plasticizers viz. dibutyl phthalate (DBP), dioctylphthalate (DOP), di-(butyl) butyl phosphate (DBBP) and tris-(2-ethylhexylphosphate) (TEHP), has also been studied on the performance of membrane sensor. It was observed that the membrane containing the composition AT: PVC: DBP in the ratio 2 : 20 : 15 displayed a useful analytical response with excellent reproducibility, low detection limit, wide working pH range (1–3.5), quick response time (15 s) and applicability over a wide concentration range of Fe(III) ions from 1 × 10-7 M to 1 × 10-1 M with a slope of 20 ± 1 mV per decade. The selectivity coefficients were determined by the mixed solution method and revealed that the electrode was selective for Fe(III) ions in the presence of interfering ions. The electrode was used for atleast 5 months without any considerable divergence in response characteristics. The constructed sensor was used as indicator electrode in the potentiometric titration of Fe(III) ions against EDTA and Fe(III) determination in rock sample, pharmaceutical sample and water sample. The results are found to be in good agreement with those obtained by using conventional methods.

  17. High-rate aluminium yolk-shell nanoparticle anode for Li-ion battery with long cycle life and ultrahigh capacity.

    Science.gov (United States)

    Li, Sa; Niu, Junjie; Zhao, Yu Cheng; So, Kang Pyo; Wang, Chao; Wang, Chang An; Li, Ju

    2015-01-01

    Alloy-type anodes such as silicon and tin are gaining popularity in rechargeable Li-ion batteries, but their rate/cycling capabilities should be improved. Here by making yolk-shell nanocomposite of aluminium core (30 nm in diameter) and TiO2 shell (∼3 nm in thickness), with a tunable interspace, we achieve 10 C charge/discharge rate with reversible capacity exceeding 650 mAh g(-1) after 500 cycles, with a 3 mg cm(-2) loading. At 1 C, the capacity is approximately 1,200 mAh g(-1) after 500 cycles. Our one-pot synthesis route is simple and industrially scalable. This result may reverse the lagging status of aluminium among high-theoretical-capacity anodes. PMID:26243004

  18. Argon and krypton Auger spectra induced by ion bombardment of aluminium and silicon surfaces

    International Nuclear Information System (INIS)

    Measurements are reported of Auger (autoionization) spectra of Ar and Kr produced by bombarding Al and Si substrates with Ar+ and Kr+ ions in the 110 eV-5 keV energy range. These are shown to be consistent with the simple Doppler model suggested, for Ne and Al and Si, in a previous paper. Once corrected using the model, the observed Auger energies are shown to correspond to theoretical predictions produced using Dirac-Fock calculations. (Author)

  19. Aluminium and calcium ions binding to pectin in sugar beet juice: Model of electrical double layer

    Directory of Open Access Journals (Sweden)

    Kuljanin Tatjana A.

    2014-01-01

    Full Text Available In sugar industry, there is a problem of the presence of undesirable macromolecules such as pectins in sugar beet juice. Separation of these compounds is done mostly by CaO. Calcium may cause undesirable process of alkalization of soil in the near environment of the sugar factory. The theoretical basis of new juice purificatin method based on the application of Al2(SO43, CaSO4 and their mixtures are presented. Two model solutions of pectin (0.1 % w/w are investigated using a method of measuring zeta potential. Pure salts Al2(SO43 and CaSO4, showed better binding properties with the pectin than mixtures. Amount of all studied pure salts and mixtures of Al3+ and Ca2+ ions were significantly less (142 - 710 mg/gpectin than the average amount of CaO used in classical process (about 9 g/gpectin. Mechanism of discharge of pectin macromolecules in the presence of mixtures of these ions using a model of double electric layer are suggested.

  20. Stress relief and texture formation in aluminium nitride by plasma immersion ion implantation

    International Nuclear Information System (INIS)

    The effect on the intrinsic stress in AlN films of applying pulsed bias during cathodic arc deposition has been studied. We find that the stress depends only on the pulse voltage-pulse frequency product, V f. The form of the dependence is well fitted by an exponential function whose parameters can be interpreted physically. The preferred orientation changes progressively with V f, from hexagonal crystallites having their direction in the plane of the film at low V f, to hexagonal crystallites having their direction normal to the plane of the film at high V f. The in-plane orientation may be consistent with energy minimization in a biaxial stress field whereas the normal orientation is consistent with the alignment of a channelling direction with the ion beam

  1. Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution.

    Science.gov (United States)

    Stojković, Aleksandra; Tajber, Lidia; Paluch, Krzysztof J; Djurić, Zorica; Parojčić, Jelena; Corrigan, Owen I

    2014-03-01

    Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO4)2(Cl)2(ciprofloxacin)2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests. PMID:24670353

  2. Biopharmaceutical characterisation of ciprofloxacin-metallic ion interactions: Comparative study into the effect of aluminium, calcium, zinc and iron on drug solubility and dissolution

    Directory of Open Access Journals (Sweden)

    Stojković Aleksandra

    2014-03-01

    Full Text Available Ciprofloxacin bioavailability may be reduced when ciprofloxacin is co-administered with metallic ion containing preparations. In our previous study, physicochemical interaction between ciprofloxacin and ferrous sulphate was successfully simulated in vitro. In the present work, comparative in vitro ciprofloxacin solubility and dissolution studies were performed in the reactive media containing aluminium hydroxide, calcium carbonate or zinc sulphate. Solid phases collected from the dissolution vessel with aluminium hydroxide, calcium carbonate and zinc sulphate were investigated for their properties. The results obtained indicate that different types of adducts may form and retard ciprofloxacin solubility and dissolution. In the case of aluminium, no phase changes were observed. The solid phase generated in the presence of calcium carbonate was identified as hydrated ciprofloxacin base. Similarly to iron, a new complex consistent with Zn(SO42(Cl2(ciprofloxacin2 × nH2O stoichiometry was generated in the presence of relatively high concentrations of ciprofloxacin hydrochloride and zinc sulphate, indicating that small volume dissolution experiments can be useful for biorelevant dissolution tests.

  3. Co-reduction behaviors of lanthanum and aluminium ions in LiCl-KCl eutectic

    International Nuclear Information System (INIS)

    In this work, the co-reduction of La(III) and Al(III) ions on the Mo electrode was investigated in LiCl-KCl eutectic at 723-806 K. Cyclic voltammetry (CV), square wave voltammetry (SWV), and open-circuit chronopotentiometry (OCP) techniques were employed to investigate the electrochemical behaviors of the co-reduction. From the CV and SWV results, the formation signals of five kinds of Al-La intermetallic compounds, which could be attributed to AlLa3, AlLa, Al2La, Al3La and Al11La3, were observed. The thermodynamic properties of La-Al intermetallic compounds in the temperature range of 723-806 K were estimated by the OCP results. The changes of Gibbs energies, enthalpies and entropies of formation and the apparent standard potentials of La-Al intermetallic compounds were evaluated. Finally, potentiostatic electrolyses at 723 K and galvanostatic electrolyses at 806 K were carried out to confirm the co-reduction process, and the products obtained were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analyses. It was found that the co-reduction products of Al11La3, Al3La and Al2La were obtained

  4. Naphthol-based fluorescent sensors for aluminium ion and application to bioimaging.

    Science.gov (United States)

    Liu, Bin; Wang, Pan-Feng; Chai, Jie; Hu, Xiang-Quan; Gao, Tingting; Chao, Jian-Bin; Chen, Ting-Gui; Yang, Bin-Sheng

    2016-11-01

    Three naphthol Schiff base-type fluorescent sensors, 1,3-Bis(2-hydroxy-1-naphthylideneamino)propane (L1), 1,3-Bis(1-naphthylideneamino)-2-hydroxypropane (L2) and 1,3-Bis(2-hydroxy-1-naphthylideneamino)-2-hydroxypropane (L3), have been synthesized. Their recognition abilities for Al(3+) are studied by fluorescence spectra. Coordination with Al(3+) inhibited the CN isomerization of Schiff base which intensely increase the fluorescence of L1-L3. Possessing a suitable space coordination structure, L3 is a best selective probe for Al(3+) over other metal ions in MeOH-HEPES buffer (3/7, V/V, pH=6.6, 25°C, λem=435nm). A turn-on ratio over 140-fold is triggered with the addition of 1.0 equiv. Al(3+) to L3. The binding constant Ka of L3-Al(3+) is found to be 1.01×10(6.5)M(-1) in a 1:1 complex mode. The detection limit for Al(3+) is 0.05μM. Theoretical calculations have also been included in support of the configuration of the L3-Al(3+) complex. Importantly, the probe L3 has been successfully used for fluorescence imaging in colon cancer SW480 cells. PMID:27285474

  5. The effect of copper ions, aluminium ions and their mixtures on separation of pectin from the sugar beet juice

    OpenAIRE

    Kuljanin Tatjana A.; Mišljenović Nevena M.; Koprivica Gordana B.; Jevrić Lidija R.; Grbić Jasna P.

    2013-01-01

    In sugar industry there is a problem of the presence of undesirable macromolecules compounds such as pectin in sugar beet juice. The affinity of calcium ions commonly used in the sugar industry for the removal of pectin from the sugar beet juice is relatively small. Coagulation and precipitation of pectin can be performed by process of discharging that is chemically induced. Compounds with di- and trivalent cations such as pure CuSO4, Al2(SO4)3 or their mixtures can be applied for clari...

  6. Structural and luminescence studies of europium ions in lithium aluminium borophosphate glasses

    Institute of Scientific and Technical Information of China (English)

    Poh Sum Wong; Ming Hua Wan; Rosli Hussin; Hendrik O Lintang; Salasiah Endud

    2014-01-01

    Eu3+doped borophosphate glasses with the chemical composition 20Li2O-30Al2O3-10B2O3-40P2O5-xEu2O3 (where x=0.05 mol.%, 0.1 mol.%, 1.0 mol.%, 1.5 mol.%and 2.0 mol.%) were prepared by conventional melt quenching technique. The structural and luminescence properties of the prepared Eu3+doped borophosphate glasses were studied and compared with reported results. The XRD pattern showed the amorphous nature of the prepared glasses. Whereas, the FTIR spectra revealed the vibrational modes in the prepared glasses. The bonding parameters (βandδ) were calculated through the excitation spectra. Judd-Ofelt (J-O) intensity pa-rameters were calculated from the emission spectra and were used to determine transition probability (A), stimulated emission cross-section (σEP ), radiative lifetime (τR) and branching ratios (βexp) for the transition 5D0→7Fj (j=1, 2, 3 and 4) of Eu3+ ions. Furthermore, the luminescence intensity ratio (R) of 5D0→7F2 to 5D0→7F1 transition was also calculated. Transition 5D0→7F2 had the highest value of stimulated emission cross-section and branching ratios and the results were comparable with the reported values. This indicated that the present glass is promising host material for Eu3+doped fiber amplifiers.

  7. High-rate aluminium yolk-shell nanoparticle anode for Li-ion battery with long cycle life and ultrahigh capacity

    OpenAIRE

    Li, Sa; Niu, Junjie; Zhao, Yu Cheng; So, Kang Pyo; Wang, Chao; Wang, Chang An; Li, Ju

    2015-01-01

    Alloy-type anodes such as silicon and tin are gaining popularity in rechargeable Li-ion batteries, but their rate/cycling capabilities should be improved. Here by making yolk-shell nanocomposite of aluminium core (30 nm in diameter) and TiO[subscript 2] shell (~3 nm in thickness), with a tunable interspace, we achieve 10 C charge/discharge rate with reversible capacity exceeding 650 mAh g[superscript −1] after 500 cycles, with a 3 mg cm[superscript −2] loading. At 1 C, the capacity is approxi...

  8. Assessment of Trace Metal Ions on Raw and Treated Water in Dakahlia Drinking water Purification Stations .Behaviour of aluminium in water purification plants

    International Nuclear Information System (INIS)

    The technology of improvement of water quality at water purification plants can be characterised by a large diversity of method and processes employed and by substantial differences in the design and process structure and equipment. The effect of operational parameters as ph, pre-, post- chlorination, coagulant index and mixing intensities on the level of some metal ions concentration in different sources of drinking water plants were studied. Results of the chemical analysis indicated that the dissolved and total AI3+ concentration in treated water was much higher than raw water and sometimes with values over the international maximum limit. Much of the overall variation in aqua aluminium ion in treated water could be explained on the basis of ph, solubility, and filtration models efficiency, while ions as Fe3+ and Mn2+ were found within the acceptable limits. The data obtained indicated that relation between watershed inputs (CI2, H CI, alum dose) and output of soluble aluminium was not necessary simple and straightforward. The investigated water samples were collected from main stations and compact units in Dakahlia Governorate

  9. The influence of the oxygen partial pressure on the ion nitriding of aluminium - An investigation by means of real time elastic recoil detection analysis

    International Nuclear Information System (INIS)

    Aluminium is known to be a difficult candidate for successful nitriding. It exhibits a dense native surface oxide layer that acts as a barrier for diffusional nitrogen transport. To investigate the influence of the oxygen partial pressure, samples of pure polycrystalline Al were ion nitrided at different oxygen partial pressures from a hot filament ion source. Before and during the nitriding process depth profiling of nitrogen and oxygen has been performed by real time elastic recoil detection analysis. The oxygen partial pressure plays a crucial role for the evolution of the surface oxide layer and thus for the nitriding result. If the surface oxide layer is removed an AlN-layer grows. The evolution of the oxide layer is compared to semi-quantitative considerations on the interplay of sputtering and oxidation. A criteria for the removal of the surface oxide layer is given

  10. Role of natural organic matter in the mobility of aluminium ions in rivers in the Limousin region (France)

    OpenAIRE

    Guibaud, Gilles; Gauthier, Cécile; Ayele, Josiane

    2000-01-01

    Rôle de la matière organique naturelle dans la mobilité de l'aluminium dans les cours d'eau en Limousin (France). Pour étudier le rôle de la matière organique, en Limousin (France), sur la mobilité de l'aluminium des sols vers les cours d'eau et sa chimie dans l'eau, les trois horizons A1 d'un sol brun acide planté de trois forêts différentes (châtaigniers (Castanea sativa), jeunes Douglas (Pseudotsuga menzesii), Douglas centenaires) et cinq points sur quatre des principales rivières (Vienne,...

  11. The role of Mg2+ ions in the corrosion behaviour of AA2024-T3 aluminium alloys immersed in chloride-containing environments

    International Nuclear Information System (INIS)

    It is well-known the harmful impact of chloride ions in the corrosion behaviour of aluminium and its alloys. The present work investigates the use of Mg2+ ions as corrosion inhibitors of AA2024-T3 samples immersed in chloride-containing electrolytes. AA2024-T3 samples were immersed into an electrolyte containing chloride ions, in absence or presence of Mg2+. The electrochemical behaviour was studied by potentiondynamic polarization and electrochemical impedance spectroscopy techniques. The results showed the beneficial effects afforded by the Mg2+ ions. First, the open circuit potential was shifted towards more cathodic values and, on the other hand, the impedance values obtained for samples tested in presence of Mg2+ were higher, suggesting a slowdown of the corrosion rate. The morphological characterization was performed using scanning electron microscopy and energy dispersive X-ray spectroscopy. The results demonstrated that the presence Mg2+ hinders Mg dealloying of the S phase particles, which delays their change from anodic to cathodic behaviour, so delaying the subsequent Al matrix galvanic attack. An additional protection mechanism is related to the blockage of cathodic areas by the precipitation of Mg(OH)2 in alkaline environments

  12. Automotive Aluminium Recycling

    Energy Technology Data Exchange (ETDEWEB)

    Gelas, B. des

    2000-07-01

    This paper aims at providing an overview on the contribution of aluminium recycling in the supply of new aluminium for automotive applications. Based on a presentation on how the global European automotive aluminium supply requirements are met, an analysis of the present and future contribution of automotive aluminium recycling is first presented. Current situation and future developments for automotive aluminium recycling practices are then commented, together with an outline on design principles for easier aluminium recycling. (orig.)

  13. Aluminium structural elements

    OpenAIRE

    Švent, Nejc

    2016-01-01

    This thesis focuses on the structural analysis of aluminium structural members in accordance with the SIST EN 1999-1-1 standard. In the introduction, historical development of aluminium is summarized, as well as the processes of structural aluminium production and manufacture. Predominantly, resistance control checks of aluminium structural members are covered, with special attention to the major contrasts between aluminium and steel structural analyses. Finally, fundamental examples of resis...

  14. Excitation wavelength-sensitive multi-colour fluorescence in Eu/Tb ions doped yttrium aluminium garnet glass ceramics

    International Nuclear Information System (INIS)

    Eu/Tb doped yttrium aluminium garnet (YAG) glass ceramics, containing single phase of YAG micro-crystals with an excellent orientation (1 1 1) in the matrix, have been prepared by heat-treating lithium–yttrium–aluminium–silicate (LYAS) precursor glasses. A group of dynamic-colour white fluorescences with different colour temperatures are achieved in Eu/Tb codoped YAG glass ceramics, attributing to the simultaneous generation of three primary colour (RGB) emissions from Eu3+ (red), Eu2+ (blue), and Tb3+ (green) by varying the UV radiation wavelength. The favourable bright white light with the colour coordinate (0.360, 0.308) close to the equal energy point is obtained under 365 nm excitation. These admirable results indicate that the Eu/Tb codoped YAG glass ceramics are a promising candidate to develop white light sources under the excitation of commercial UV-LEDs. - Highlights: ► RE doped glass ceramics (GC) have been derived by heat-treating LYAS mother glasses. ► Single phase of YAG crystals has determined in RE doped GC. ► YAG micro-crystals grow with an excellent orientation (1 1 1) in RE doped GC. ► Two distinct luminescence centres of Eu in YAG GC have been identified. ► Excitation wavelength-sensitive white light has been achieved in Eu/Tb doped YAG GC.

  15. TEM investigation of aluminium containing precipitates in high aluminium doped silicon carbide

    International Nuclear Information System (INIS)

    Full text: Silicon carbide is a promising semiconductor material for applications in high temperature and high power devices. The successful growth of good quality epilayers in this material has enhanced its potential for device applications. As a novel semiconductor material, there is a need for studying its basic physical properties and the role of dopants in this material. In this study, silicon carbide epilayers were grown on 4H-SiC wafers of (0001) orientation with a miscut angle of 8 deg at a temperature of 1550 deg C. The epilayers contained regions of high aluminium doping well above the solubility of aluminium in silicon carbide. High temperature annealing of this material resulted in the precipitation of aluminium in the wafers. The samples were analysed by secondary ion mass spectrometry and transmission electron microscopy. Selected area diffraction studies show the presence of aluminium carbide and aluminium silicon carbide phases. Copyright (2002) Australian Society for Electron Microscopy Inc

  16. Electron spin resonance and optical absorption spectroscopic studies of Cu2+ ions in aluminium lead borate glasses

    International Nuclear Information System (INIS)

    Highlights: ► It is for the first time to study optical absorption and EPR in these glasses. ► The thermal properties are new and interesting in this glass system. ► It is for the first time to report three optical bands for Cu2+ in oxide glasses. ► The interesting optical results are due to excellent sample preparation. - Abstract: Electron Spin Resonance and optical absorption spectral studies of Cu2+ ions in 5 Al2O3 + 75 B2O3 + (20-z) PbO + z CuO (where z = 0.1–1.5 mol.% of CuO) glasses have been reported. The EPR spectra of all the glasses show resonance signals characteristic of Cu2+ ions at both room and low temperatures. The number of spins and Gibbs energy were calculated at different concentrations and temperatures. From the plot of the ratio of logarithmic number of spins and absolute temperature and the reciprocal of absolute temperature, the entropy and enthalpy have been evaluated. The optical absorption spectra of all the glasses exhibit three bands and these bands have been assigned to 2B1g → 2Eg, 2B1g → 2B2g, and 2B1g → 2A1g transitions in the decreasing order of energy. It is for the first time to observe three optical absorption bands for Cu2+ ions in oxide glasses. Such type of results is due to excellent sample preparation. From the EPR and optical absorption spectroscopies data, the molecular orbital coefficients have been evaluated.

  17. Phase analysis of nickel surface layer implanted by aluminium

    International Nuclear Information System (INIS)

    The experimental result of study of microstructure and phase composition in the surface zone of nickel target under intensive implantation of aluminium ions on a vacuum-arc and plasma flow source Raduga-5 are presented. It was established that the fine dispersed intermetallic precipitates Ni3Al and NiAl and the variable composition solid solution of aluminium in nickel are formed

  18. Some Phthalocyanine and Naphthalocyanine Derivatives as Corrosion Inhibitors for Aluminium in Acidic Medium: Experimental, Quantum Chemical Calculations, QSAR Studies and Synergistic Effect of Iodide Ions

    Directory of Open Access Journals (Sweden)

    Masego Dibetsoe

    2015-08-01

    Full Text Available The effects of seven macrocyclic compounds comprising four phthalocyanines (Pcs namely 1,4,8,11,15,18,22,25-octabutoxy-29H,31H-phthalocyanine (Pc1, 2,3,9,10,16,17,23,24-octakis(octyloxy-29H,31H-phthalocyanine (Pc2, 2,9,16,23-tetra-tert-butyl-29H,31H-phthalocyanine (Pc3 and 29H,31H-phthalocyanine (Pc4, and three naphthalocyanines namely 5,9,14,18,23,27,32,36-octabutoxy-2,3-naphthalocyanine (nPc1, 2,11,20,29-tetra-tert-butyl-2,3-naphthalocyanine (nPc2 and 2,3-naphthalocyanine (nP3 were investigated on the corrosion of aluminium (Al in 1 M HCl using a gravimetric method, potentiodynamic polarization technique, quantum chemical calculations and quantitative structure activity relationship (QSAR. Synergistic effects of KI on the corrosion inhibition properties of the compounds were also investigated. All the studied compounds showed appreciable inhibition efficiencies, which decrease with increasing temperature from 30 °C to 70 °C. At each concentration of the inhibitor, addition of 0.1% KI increased the inhibition efficiency compared to the absence of KI indicating the occurrence of synergistic interactions between the studied molecules and I− ions. From the potentiodynamic polarization studies, the studied Pcs and nPcs are mixed type corrosion inhibitors both without and with addition of KI. The adsorption of the studied molecules on Al surface obeys the Langmuir adsorption isotherm, while the thermodynamic and kinetic parameters revealed that the adsorption of the studied compounds on Al surface is spontaneous and involves competitive physisorption and chemisorption mechanisms. The experimental results revealed the aggregated interactions between the inhibitor molecules and the results further indicated that the peripheral groups on the compounds affect these interactions. The calculated quantum chemical parameters and the QSAR results revealed the possibility of strong interactions between the studied inhibitors and metal surface. QSAR

  19. Some Phthalocyanine and Naphthalocyanine Derivatives as Corrosion Inhibitors for Aluminium in Acidic Medium: Experimental, Quantum Chemical Calculations, QSAR Studies and Synergistic Effect of Iodide Ions.

    Science.gov (United States)

    Dibetsoe, Masego; Olasunkanmi, Lukman O; Fayemi, Omolola E; Yesudass, Sasikumar; Ramaganthan, Baskar; Bahadur, Indra; Adekunle, Abolanle S; Kabanda, Mwadham M; Ebenso, Eno E

    2015-01-01

    The effects of seven macrocyclic compounds comprising four phthalocyanines (Pcs) namely 1,4,8,11,15,18,22,25-octabutoxy-29H,31H-phthalocyanine (Pc1), 2,3,9,10,16,17,23,24-octakis(octyloxy)-29H,31H-phthalocyanine (Pc2), 2,9,16,23-tetra-tert-butyl-29H,31H-phthalocyanine (Pc3) and 29H,31H-phthalocyanine (Pc4), and three naphthalocyanines namely 5,9,14,18,23,27,32,36-octabutoxy-2,3-naphthalocyanine (nPc1), 2,11,20,29-tetra-tert-butyl-2,3-naphthalocyanine (nPc2) and 2,3-naphthalocyanine (nP3) were investigated on the corrosion of aluminium (Al) in 1 M HCl using a gravimetric method, potentiodynamic polarization technique, quantum chemical calculations and quantitative structure activity relationship (QSAR). Synergistic effects of KI on the corrosion inhibition properties of the compounds were also investigated. All the studied compounds showed appreciable inhibition efficiencies, which decrease with increasing temperature from 30 °C to 70 °C. At each concentration of the inhibitor, addition of 0.1% KI increased the inhibition efficiency compared to the absence of KI indicating the occurrence of synergistic interactions between the studied molecules and I(-) ions. From the potentiodynamic polarization studies, the studied Pcs and nPcs are mixed type corrosion inhibitors both without and with addition of KI. The adsorption of the studied molecules on Al surface obeys the Langmuir adsorption isotherm, while the thermodynamic and kinetic parameters revealed that the adsorption of the studied compounds on Al surface is spontaneous and involves competitive physisorption and chemisorption mechanisms. The experimental results revealed the aggregated interactions between the inhibitor molecules and the results further indicated that the peripheral groups on the compounds affect these interactions. The calculated quantum chemical parameters and the QSAR results revealed the possibility of strong interactions between the studied inhibitors and metal surface. QSAR analysis on the

  20. Eletrodo íon-seletivo para determinação potenciométrica de alumínio(III em meio de fluoreto Ion-selective electrode for potentiometric determination of aluminium(III in fluoride medium

    Directory of Open Access Journals (Sweden)

    Evandro Piccin

    2004-12-01

    Full Text Available The construction and analytical evaluation of a coated graphite Al(III ion-selective electrode, based on the ionic pair formed between the Al(Fn3-n anion and tricaprylylmethylammonium cation (Aliquat 336S incorporated on a poly(vinylchloride (PVC matrix membrane are described. A thin membrane film of this ionic pair and dibutylphthalate (DBPh in PVC was deposited directly on a cylindric graphite rod (2 cm length x 0.5 cm diameter attached to the end of a glass tube using epoxy resin. The membrane solution was prepared by dissolving 40% (m/m of PVC in 10 mL of tetrahydrofuran following addition of 45% (m/m of DBPh and 15% (m/m of the ionic pair. The effect of membrane composition, fluoride concentration, and several concomitants as potential interferences on the electrode response were investigated. The aluminium(III ion-selective electrode showed a linear response ranging from 1.4 x 10-4 to 1.0 x 10-2 mol L-1, a detection limit of 4.0 x 10-5 mol L-1, aslope of -54.3±0.2mV dec-1 and a lifetime of more than 1 year (over 3000 determinations for each membrane. The slope indicates that the ion-selective electrode responds preferentially to the Al(F4- species. Application of this electrode for the aluminium(III determination in stomach anti-acid samples is reported.

  1. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    OpenAIRE

    Napachat Tareelap; Kaysinee Sriraksasin; Nakorn Srisukhumbowornchai; Swieng Thuanboon; Choochat Nitipanyawong

    2014-01-01

    Due to the failure of manganese aluminium bronze (MAB) propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium...

  2. Recovery in aluminium

    DEFF Research Database (Denmark)

    Gundlach, Carsten

    2006-01-01

    growth curves are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold......In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X......-ray diffraction technique for studies of the evolution of grains within polycrystalline materials. The much smaller volume of the crystallites of interest here in comparison to grains implies that the existing method is not applicable due to overlap of diffraction spots. In this work this obstacle is overcome by...

  3. Soldering of aluminium alloys

    International Nuclear Information System (INIS)

    A literature survey about soldering in general and aluminium alloys soldering in particular is presented. The existing methods of soldering aluminium alloys are described. These include soldering with flux, soldering after preliminary plating, vacuum brazipressure and temperature (NTP), sample age calculation based on 14C half life of 5570 and 5730 years, age correction for NTP, dendrochronological corrections and the relative radiocarbon concentration. All results are given with one standard deviation. Input data test (Chauvenet's criterion), gas purity test, standard deviation test and test of the data processor are also included in the program. (author)

  4. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.H.H.; Soetens, F.

    2006-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical pr

  5. Spectrofluorimetric determination of microquantities of aluminium in uranium

    International Nuclear Information System (INIS)

    A rapid and sensitive method for the separation and spectrofluorimetric determination of microamounts of aluminium in uranium compounds is described. In sodium carbonate solution at pH 9.5-10.0, the uranyl ion forms a very stable anionic complex with the carbonate ion. In these conditions, uranium is not extracted by a chloroform oxine solution, while alumium is isolated as the tris(oxinate)aluminium(III) form. The interferences are previously extracted with chloroform as diethylditiocarbomates in the same tris(oxinate)aluminum(III) pH extraction. The sensitivity is 0,005 μ Al/ml of organic phase and the relative standard deviation is 10%

  6. Studies on an aluminium-carbon cell

    Science.gov (United States)

    Verma, L. K.

    The current-voltage behaviour of an electrochemical cell that consists of an aluminium anode and a carbon cathode in a medium containing aqueous NH 4SCN has been studied, both in the presence and in the absence of a coating on the carbon electrode. It is found that activation polarization is the main factor that limits the current output when using an untreated carbon electrode. This problem is eliminated by coating the carbon electrode with an in situ deposition of HgI 2. In this condition, the current output is reduced mainly by ohmic polarization. Further studies with a coated HgI 2-carbon cathode and an aluminium anode, in a medium containing SCN - and Cl - ions together with a complexing agent (EDTA, sodium salt), revealed that a cell performance close to ideal, (i.e, showing no appreciable polarization) can be obtained at currents up to 0.6 mA/cm 2 and above.

  7. Recovery in aluminium

    OpenAIRE

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X-ray diffraction technique for studies of the evolution of grains within polycrystalline materials. The much smaller volume of the crystallites of interest here in comparison to grains implies that the ...

  8. Aluminium and human breast diseases.

    Science.gov (United States)

    Darbre, P D; Pugazhendhi, D; Mannello, F

    2011-11-01

    The human breast is exposed to aluminium from many sources including diet and personal care products, but dermal application of aluminium-based antiperspirant salts provides a local long-term source of exposure. Recent measurements have shown that aluminium is present in both tissue and fat of the human breast but at levels which vary both between breasts and between tissue samples from the same breast. We have recently found increased levels of aluminium in noninvasively collected nipple aspirate fluids taken from breast cancer patients (mean 268 ± 28 μg/l) compared with control healthy subjects (mean 131 ± 10 μg/l) providing evidence of raised aluminium levels in the breast microenvironment when cancer is present. The measurement of higher levels of aluminium in type I human breast cyst fluids (median 150 μg/l) compared with human serum (median 6 μg/l) or human milk (median 25 μg/l) warrants further investigation into any possible role of aluminium in development of this benign breast disease. Emerging evidence for aluminium in several breast structures now requires biomarkers of aluminium action in order to ascertain whether the presence of aluminium has any biological impact. To this end, we report raised levels of proteins that modulate iron homeostasis (ferritin, transferrin) in parallel with raised aluminium in nipple aspirate fluids in vivo, and we report overexpression of mRNA for several S100 calcium binding proteins following long-term exposure of MCF-7 human breast cancer cells in vitro to aluminium chlorhydrate. PMID:22099158

  9. Method of aluminium fluoride manufacture

    International Nuclear Information System (INIS)

    The manufacture of aluminium fluoride is based on waste processing in uranium hexafluoride conversion to uranium oxides within the fuel cycle. The conversion is the stoichiometric conversion of uranium hexafluoride with aluminium nitrate to uranyl nitrate. This is extracted from the water phase by phosphoric acid trialkyl ester to an organic solvent and further processed. The discharge water phase is solidified by evaporation to solid aluminium fluoride and nitric acid. (M.S.)

  10. Analytical study, by modelling methods, of the alkali and alkaline earth cations influence on the stability and the reactivity of aluminium (III) oxides or halides complexes; Etude analytique, par des techniques de modelisation, de l`influence de cations alcalins ou alcalino-terreux sur la stabilite et la reactivite de complexes de l`aluminium(III) avec des ions halogenures ou oxydes

    Energy Technology Data Exchange (ETDEWEB)

    Bouyer, F.

    1995-10-05

    The electric power consumption in aluminium production and electrorefining processes is high. A study of the electrochemical processes can be very useful for a better understanding of phenomena in electrolytic baths and then for reducing the production costs. A structural and vibrational analysis of species which exist in ionic solutions has been carried out with software based on the functional density theory. Concerning the electrolyte used for the aluminium refining, the anions study has shown that the aluminium chloro-fluoride complexes are preferentially tetrahedral. Moreover, the aluminium oxyfluoride complexes structures (which come from the alumina dissolution in cryolitic media) have been analyzed in the same way and the preferential coordination numbers for aluminium and oxygen have been shown clearly. The anionic model (which is limited to the nearest aluminium neighbours) does not allow to account for the thermodynamics of the cryolitic media. A more elaborated model has then been found to obtain the cryolite structure. The reactions enthalpies have been estimated and have lead to the calculus of species concentration gradients in liquid phase. The counterions effects as for instance sodium and calcium have been investigated. A model for the gaseous phase allowing to know the preferential species has been given. At last, a statistic thermochemistry program has been conceived and developed. It gives the thermodynamical functions at all temperature for the different complexes and allows to reckon the reactions coefficients in gaseous phase as well as the partial pressures profiles with those of calcium and sodium fluorides. (O.M.) 204 refs.

  11. RAMAN SPECTRUM STUDIES OF THE COORDINATIONS OF ALUMINIUM AND BORON IN Na2O-Al2O3-B2O3-P2O5 GLASSES

    OpenAIRE

    Yifen, Yin; Dehua, Jiang; Xiangsheng, Chen; Beiya, Bian; Xihuai, Huang

    1985-01-01

    The coordination states of aluminium and boron in Na2O-Al2O3-B2O3-P2O5 glasses have been studied by means of Raman spectroscopy. The study shows that when boron and aluminium ions exist simultaneously in phosphate glasses, it is possible that boron ions form BO4 tetrahedra prior to aluminium ions, and the former has three and four coordinations while the latter has four and six.

  12. First Principles Study of Aluminium Vacancy in Wurtzite Aluminium Nitride

    Institute of Scientific and Technical Information of China (English)

    GAO Ting-Ge; YI Jue-Min; ZHOU Zi-Yao; HU Xiao-Dong

    2008-01-01

    @@ We report that the aluminium vacancy in wurtzite AIN brings about two impurity levels e and a2 in the band gap, not just one single t2 level The aluminium vacancy carries a magnetic moment of 1 μB in the ground state. The molecule orbit of the aluminium vacancy becomes e↑↑ a2↑ rather than e↑↑ a2↑. The calculation is carried out by using the CASTEP code. The intrinsic symmetry of wurtzite A1N is the driving force for this spin splitting. Finally the symmetry of wurtzite AlN results in an anti-ferromagnetic coupling between the aluminium vacancies, as is predicted. Our findings are helpful to gain a more through understanding of the structural and spin property of aluminium vacancy in wurtzite AIN.

  13. Determination of ultratrace amounts of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization/ICP-MS

    International Nuclear Information System (INIS)

    A method has been developed for determining the 0.01 ng g-1 level of uranium and thorium in aluminium and aluminium alloys by electrothermal vaporization (ETV)/ICP-MS. This method was found to be significantly interfered with any matrices or other elements contained. An ion-exchange technique was therefore applied to separate uranium and thorium from aluminium and other elements. It was known that uranium are adsorbed on an anion-exchange resin and thorium are adsorbed on cation-exchange resin. However, aluminium and copper were eluted with 6 M hydrochloric acid. Dissolve the sample with hydrochloric acid containing copper which was added for analysis of pure aluminium, and oxidize with hydrogen peroxide. Concentration of hydrochloric acid in the solution was adjusted to 6 M, and then passed the solution through the mixed ion-exchange resin column. After the uranium and thorium were eluted with 1 M hydrofluoric acid-0.1 M hydrochloric acid, the solution was evaporated to dryness. It was then dissolved with 1 M hydrochloric acid. Uranium and thorium were analyzed by ETV/ICP-MS using tungsten and molybdenum boats, respectively, since the tungsten boat contained high-level thorium and the molybdenum boat contained uranium. The determination limit of uranium and thorium were 0.003 and 0.005 ng g-1, respectively. (author)

  14. Study into interaction of aluminium sulfate with meta-, pyro- and ortho-vanadates of lithium in aqueous solutions

    International Nuclear Information System (INIS)

    The method of samples series with a variable vanadium concentration was used to study the reaction of aluminium ions with meta-, pyro- and orthovanadate ions in aqueous solutions. The authors propose equations describing the reactions, which are in good agreement with the present-day notions of the state of aluminium and vanadium ions in aqueous solutions. It has been established that mixing of aluminium and vanadium solutions yields, at pH 3.5-3.8 hydrodecavanadates of hydroxaluminium of composition [Al(OH)sub(x)]sub(6-y)Hsub(y)Vsub(10)Osub(28) regardless of the composition of the vanadate ions

  15. Decreased toxicity of aluminium when the ionic strength increases in water; Blir aluminium mindre toksisk naar ionestyrken i vannet oeker?

    Energy Technology Data Exchange (ETDEWEB)

    Alstad, E.W. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper evaluates the acute mortality of fish caused by the toxicity of aluminium in water. The evaluation is based on the polymerization hypothesis. According to the author, the level of toxicity decreases when the concentration and charge of ions increase. The paper presents the preliminary results from the executed experiment. 2 refs., 2 figs., 1 tab.

  16. Anomalous Diffusion of Mo Implanted into Aluminium

    Institute of Scientific and Technical Information of China (English)

    张通和; 吴瑜光; 邓志威; 钱卫东

    2001-01-01

    Mo ions are implanted into aluminium with a high ion flux and high dose at elevated temperatures of 300℃, 400℃ and 500℃ . X-ray diffraction spectra show that the Al12Mo phases are formed. Rutherford backscattering spectroscopy indicates that a profile of Mo appears in Al around the depth of 550nm and with an atomic concentration of ~7%, when Mo is implanted to the dose of 3 × 1017/cm2 with an ion flux of 45μA/cm2 (400℃).If the dose increases to 1 × 1018/cm2 at the same ion flux, the penetration of Mo ions in Al can reach a depth of 2μm, which is greater than the ion project range Rp (52.5nm). The results show that anomalous diffusion takes place. Owing to the intense atom collision cascades, the diffusion coefficient increases greatly with the increase of the ion flux and dose. The Mo diffusion coefficients in Al are calculated. The Mo retained dose in A1 increases obviously with the increase of the ion flux.

  17. Water atomised aluminium alloy powders

    Energy Technology Data Exchange (ETDEWEB)

    Neikov, O.D.; Vasilieva, G.I.; Sameljuk, A.V.; Krajnikov, A.V

    2004-10-10

    The new rapid solidification (RS) process based on high-pressure water atomisation (WA) of the melt for manufacturing of advanced aluminium alloys was realised in the form of a pilot plant. The problems of safe operation in the course of Al alloy powder production and powder quality were solved by the use of water solutions of inhibitors, by the control of suspension temperature and hydrogen ion exponent (pH), by the hydraulic classification of atomised products, and by the optimisation of dehydration procedure. The rate of powder-water interaction strongly depends on the value of pH. While the rate of room temperature reactions is very slow at pH 3.0-4.0, the increase of pH to 6.0 leads to an intensive powder oxidation. A set of powder metallurgy (PM) alloys for various applications was produced on the base of water atomised powders. The characteristics of tensile strength of such alloys essentially exceed those of cast materials of similar compositions.

  18. Water atomised aluminium alloy powders

    International Nuclear Information System (INIS)

    The new rapid solidification (RS) process based on high-pressure water atomisation (WA) of the melt for manufacturing of advanced aluminium alloys was realised in the form of a pilot plant. The problems of safe operation in the course of Al alloy powder production and powder quality were solved by the use of water solutions of inhibitors, by the control of suspension temperature and hydrogen ion exponent (pH), by the hydraulic classification of atomised products, and by the optimisation of dehydration procedure. The rate of powder-water interaction strongly depends on the value of pH. While the rate of room temperature reactions is very slow at pH 3.0-4.0, the increase of pH to 6.0 leads to an intensive powder oxidation. A set of powder metallurgy (PM) alloys for various applications was produced on the base of water atomised powders. The characteristics of tensile strength of such alloys essentially exceed those of cast materials of similar compositions

  19. Prevention of Dealloying in Manganese Aluminium Bronze Propeller: Part II

    Directory of Open Access Journals (Sweden)

    Napachat Tareelap

    2014-03-01

    Full Text Available Due to the failure of manganese aluminium bronze (MAB propeller caused by dealloying corrosion as described in Part I [1], this work aims to study the prevention of dealloying corrosion using aluminium and zinc sacrificial anodes. The results indicated that both of the sacrificial anodes could prevent the propeller from dealloying. Moreover, the dealloying in seawater was less than that found in brackish water. It was possible that hydroxide ions, from cathodic reaction, reacted with calcium in seawater to form calcium carbonate film protecting the propeller from corrosion.

  20. Effect of Aluminium Content in Aluminium Pillared Montmorillonite To Its Surface Acidity Properties

    Directory of Open Access Journals (Sweden)

    Is Fatimah

    2011-07-01

    Full Text Available Aluminium pillared montmorillonites from Indonesian natural montmorillonite has been prepared using Al13 Keggin ion pillaring precursor in varied concentrations. Herein we studied their characterization and catalysis application for esterification reaction. X-ray diffraction (XRD, energy dispersive x-ray analysis (EDX, and BET gas sorption analysis were employed to characterize the prepared materials besides the characterization on surface acidity by pyridine and n-butylammine adsorptions and FTIR analysis. The result showed that significant improvement on physicochemical character data was obtained by a pillarization process. Such a process also provided improvements on catalytic activities in esterification reactions. The effect of aluminium content on material characters was discussed in this paper. It was observed from the catalytic activity tests that pillared montmorillonite samples demonstrated higher activity in esterification reaction relative to the raw montmorillonite. It was found that surface profile of materials consist of specific surface area, pore volume and Lewis acidity were significantly affect the catalyst activity.

  1. Aluminium, antiperspirants and breast cancer.

    Science.gov (United States)

    Darbre, P D

    2005-09-01

    Aluminium salts are used as the active antiperspirant agent in underarm cosmetics, but the effects of widespread, long term and increasing use remain unknown, especially in relation to the breast, which is a local area of application. Clinical studies showing a disproportionately high incidence of breast cancer in the upper outer quadrant of the breast together with reports of genomic instability in outer quadrants of the breast provide supporting evidence for a role for locally applied cosmetic chemicals in the development of breast cancer. Aluminium is known to have a genotoxic profile, capable of causing both DNA alterations and epigenetic effects, and this would be consistent with a potential role in breast cancer if such effects occurred in breast cells. Oestrogen is a well established influence in breast cancer and its action, dependent on intracellular receptors which function as ligand-activated zinc finger transcription factors, suggests one possible point of interference from aluminium. Results reported here demonstrate that aluminium in the form of aluminium chloride or aluminium chlorhydrate can interfere with the function of oestrogen receptors of MCF7 human breast cancer cells both in terms of ligand binding and in terms of oestrogen-regulated reporter gene expression. This adds aluminium to the increasing list of metals capable of interfering with oestrogen action and termed metalloestrogens. Further studies are now needed to identify the molecular basis of this action, the longer term effects of aluminium exposure and whether aluminium can cause aberrations to other signalling pathways in breast cells. Given the wide exposure of the human population to antiperspirants, it will be important to establish dermal absorption in the local area of the breast and whether long term low level absorption could play a role in the increasing incidence of breast cancer. PMID:16045991

  2. Aluminium oxide exoelectron dosimetry

    Energy Technology Data Exchange (ETDEWEB)

    Akselrod, M.S.; Odegov, A.L. (Urals State Technical Univ., Ekaterinburg (Russian Federation)); Durham, J.S. (Pacific Northwest Lab., Richland, WA (United States))

    1994-01-01

    The exoemission properties of aluminium oxide ([alpha]-Al[sub 2]O[sub 3]:C), in the forms of both a single crystal and of powder, have been investigated. Measurements obtained during readout in a vacuum showed that irradiated Al[sub 2]O[sub 3]:C dosemeters emit exoelectrons with a sensitivity that is 10-20 times higher than that achievable using beryllium oxide (BeO) exoelectron dosemeters (EEDs). This paper presents results of studies using a commercial methane gas reader. The investigators studied the response of the Al[sub 2]O[sub 3]:C EEDs as a function of beta energy and measured the dose-response relationship. The effect of humidity on the dosemeter response was also investigated. (Author).

  3. Roll bonding of strained aluminium

    DEFF Research Database (Denmark)

    Staun, Jakob M.

    2003-01-01

    This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... circumstances both materials show good bonding, but the high purity material is excluded because of recrystallisation and the resulting loss of mechanical properties. The effect of cross stacking and roll bonding pre-strained sheets of the commercial purity material is investigated and some dependence of the...... cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

  4. Fluoride ions sorption of the water using natural and modified hematite with aluminium hydroxide; Sorcion de iones fluoruro del agua utilizando hematita natural y hematita acondicionada con hidroxido de aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Teutli S, E. A.

    2011-07-01

    Fluorine is a mineral known for its dental benefits, but fluoride ions can cause fluoro sis in excessive quantities. There are many epidemiological studies on possible adverse effects resulting from prolonged ingestion of fluoride through drinking water. These studies demonstrate that fluoride mainly affects the bone tissue (bones and teeth), may produce an adverse effect on tooth enamel and can cause mild dental fluoro sis at concentrations from 0.9 to 1.2 mg/L in drinking water. In several states of Mexico, water contaminated with fluoride ions can be found, such as Aguascalientes, Chihuahua, Coahuila, Durango, Guanajuato, Sonora, Zacatecas, San Luis Potosi and Jalisco, where the fluoride ions levels are higher than 1.5 mg/L, established by the Mexican Official Standard (NOM-127-Ssa-2000) which sets the permissible limits of water for human use and consumption. Currently, several technologies have been proposed to remove fluoride ions from water such as precipitation methods which are based on the addition of chemicals to water and sorption methods to removed fluoride ions by sorption or ion exchange reactions by some suitable substrate capable of regenerate and reuse. In this work, the sorption of fluoride ions using unmodified and modified hematite with aluminum hydroxide to remove fluoride ions from water by bath experiments was studied. The hematite was modified by treating it with aluminum hydroxide, NaOH and Al{sub 2}(SO{sub 4}){sub 3} solutions. The characterization of hematite before and after modification with aluminum hydroxide was studied by X-ray diffraction, scanning electron microscopy, EDS and Bet. The effect of ph, contact time, concentration of fluoride ions, and the dose of sorbent on the sorption of fluoride ions by the modified hematite were studied. Equilibrium was reached within 48 hours of contact time and the maximum sorption of fluoride ions were in the range pH{sub eq} between 2.3 and 6.2. Sorption capacities of fluoride ions as a

  5. Friction surfacing of aluminium alloys

    OpenAIRE

    Pereira, Diogo Jorge O. A.

    2012-01-01

    Friction surfacing is a solid state joining process that has attracted much interest in the past decades. This technology allows joining dissimilar metallic materials while avoiding the brittle intermetallic formations, involving temperatures bellow melting point and producing like forged metal structures. Much research using different steels has been made but the same does not happen with aluminium alloys, specially using different aluminium alloys. Friction surface coatings using cons...

  6. Analysis of the influence oxygen and hydrogen during melting aluminium and his alloys

    Directory of Open Access Journals (Sweden)

    A. W. Bydałek

    2011-07-01

    Full Text Available In the work was stated term the analysis of ion influences in melting codnuction of aluminium and his alloys. Influence from hydrogen and oxygen, hydrogen and oxygen and steam water together was distinguished. Where have worked out the scheme of influences leading to gas porosity of aluminium and his alloys. In analysis was referred to theory of double electric layer. It was conducted the analysis regularity of opinion influence oxygen and hydrogen in melt aluminium in support on Allena - Hewitta dependence.

  7. Spectrum Simulation of Li-Like Aluminium Plasma

    Institute of Scientific and Technical Information of China (English)

    PENG Feng; JIANG Gang; ZHU Zheng-He

    2006-01-01

    X-ray emission spectra for L-shell of Li-like aluminium ions are simulated by using the flexible atomic code based on the collisional radiative model. Atomic processes including radiative recombination, dielectronic recombination, collisional ionization and resonance excitation from the neighbouring ion (Al9+ and Al11+) charge states of the target ion (Al10+) are considered in the model. In addition, the contributions of different atomic processes to the x-ray spectrum are analysed. The results show that dielectronic recombination, radiative recombination, collisional ionization and resonance excitation, other than direct collisional excitation, are very important processes.

  8. Effect of hydrogen on aluminium and aluminium alloys: A review

    DEFF Research Database (Denmark)

    Ambat, Rajan; Dwarakadasa, E.S.

    1996-01-01

    Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen in...... aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...

  9. Sorption of strontium-90 on anodized aluminium (2)

    International Nuclear Information System (INIS)

    Adsorption of the 90Sr+90Y system on anodized aluminium as a function of oxide layer thickness, purity of aluminum and temperature has been studied. It was found that only the adsorption of Sr2+ ions is affected by the oxide layer thickness. The content of admixtures in aluminium was meaningless from the point of view of adsorption capacity. An increase of Sr2+ adsorption with temperature was observed in the range from 20 to 600C. From the investigation of desorption it follows that the irreversibility of adsorption is higher for yttrium than for strontium and that the oxide layers of greater porosity tie up more strongly both kinds of ions. (author)

  10. Buckwheat stomatal traits under aluminium toxicity

    Directory of Open Access Journals (Sweden)

    Oleksandr E. Smirnov

    2014-04-01

    Full Text Available Aluminium influence on some stomatal parameters of common buckwheat (Fagopyrum esculentum Moench. was studied. Significant changes in stomatal density, stomatal index and stomatal shape coefficient under aluminium treatment were revealed. Stomatal closure and no difference in total stomatal potential conductance index of treatment plants were suggested as aluminium resistance characteristics.

  11. Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

    Energy Technology Data Exchange (ETDEWEB)

    Vera, Rosa, E-mail: rvera@ucv.c [Instituto de Quimica, Facultad de Ciencias, Pontificia Universidad Catolica de Valparaiso, Avda. Brasil 2950, Casilla 4059, Valparaiso (Chile); Verdugo, Patricia [Departamento de Quimica y Bioquimica, Facultad de Ciencias, Universidad de Valparaiso, Av. Gran Bretana 1111, Valparaiso (Chile); Orellana, Marco; Munoz, Eduardo [Instituto de Quimica, Facultad de Ciencias, Pontificia Universidad Catolica de Valparaiso, Avda. Brasil 2950, Casilla 4059, Valparaiso (Chile)

    2010-11-15

    Research highlights: {yields} The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. {yields} In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. {yields} The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

  12. The prophylactic reduction of aluminium intake.

    Science.gov (United States)

    Lione, A

    1983-02-01

    The use of modern analytical methods has demonstrated that aluminium salts can be absorbed from the gut and concentrated in various human tissues, including bone, the parathyroids and brain. The neurotoxicity of aluminium has been extensively characterized in rabbits and cats, and high concentrations of aluminium have been detected in the brain tissue of patients with Alzheimer's disease. Various reports have suggested that high aluminium intakes may be harmful to some patients with bone disease or renal impairment. Fatal aluminium-induced neuropathies have been reported in patients on renal dialysis. Since there are no demonstrable consequences of aluminium deprivation, the prophylactic reduction of aluminium intake by many patients would appear prudent. In this report, the major sources of aluminium in foods and non-prescription drugs are summarized and alternative products are described. The most common foods that contain substantial amounts of aluminium-containing additives include some processed cheeses, baking powders, cake mixes, frozen doughs, pancake mixes, self-raising flours and pickled vegetables. The aluminium-containing non-prescription drugs include some antacids, buffered aspirins, antidiarrhoeal products, douches and haemorrhoidal medications. The advisability of recommending a low aluminium diet for geriatric patients is discussed in detail. PMID:6337934

  13. Dynamical study of liquid aluminium

    International Nuclear Information System (INIS)

    Recent molecular dynamics data of Ebbsjoe et al. in liquid aluminium have been analysed through the memory function formalism. Two forms of the memory functions which have correct asymptotic limit at large wavenumbers but accounts for interatomic correlations in a different manner are considered. The results for ω2s(q, ω) obtained from both models are compared with experimental data. (author)

  14. Aluminium foams. manufacture, properties and applications

    International Nuclear Information System (INIS)

    Aluminium foams are porous to have many interesting combinations of physical and mechanical properties, such as high stiffness in conjunction with very low specific weight. The aluminium foam structure, manufacture processes, physical, chemical and mechanical properties and applications are reviewed in this paper. The various manufacturing processes are classified according to the state of matter in which the metal is processed. Liquid aluminium can be foamed directly by injecting gas or gas-releasing blowing agents. Indirect methods include melting of powder compacts which contain a blowing agent. An inert gas entrapped in powder compacts can produce aluminium foams in solid state after heat treatment. Electron-deposition or metal vapour deposition also allow for the production of aluminium foams. Physical, chemical and mechanical properties and the various ways for characterising the aluminium foams are reviewed in second section of this paper. finally, the various application fields for aluminium foams are discussed. They are divided into different industrial sectors. (Author) 75 refs

  15. Electrochemical properties and thermal stability of epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    ZORICA M. KACAREVIC-POPOVIC

    2001-12-01

    Full Text Available The corrosion behaviour of epoxy coatings electrodeposited on aluminium, as well as on electrochemically and chemically modified aluminium were investigated during exposure to 3 % NaCl. Electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA were used for the determination of the protective properties of epoxy coatings on aluminium, anodized aluminium, phosphatized and chromatized-phosphatized aluminium. The protective properties of epoxy coatings on anodized and chromatized-phosphatized aluminium are significantly improved with respect to the same epoxy coatings on aluminium and phosphatized aluminium: higher values of the pore resitance and charge-transfer resistance, lower values of the coating capacitance, double-layer capacitance and relative permittivity (from EIS smaller amount of absorbed water inside the coating (From TGA. On the other hand, the lower values of the ipdt temperature indicate a lower thermal stability of the epoxy coatings on anodized and chromatized-phosphatized aluminium.

  16. Towards the structure of rare earth luminescence centres – terbium doped aluminium nitride as an example system

    International Nuclear Information System (INIS)

    Sputter deposited terbium doped aluminium nitride layers were investigated with respect to the distribution and surroundings of the terbium luminescence ions. Semi-empirical calculations indicate that terbium forms complexes consisting of one aluminium vacancy surrounded by three oxygen ions on nitrogen lattice positions and one nitrogen ion that is bound to a terbium ion on a distorted aluminium lattice position. The crystal field splitting of the terbium ions indicate their surroundings to be not tetrahedral but, as anticipated from the determined complex, C3v. Complementary electron microscopic investigations show a random distribution of these complexes within the layer volume. The terbium ions cause a shape of the Tb M5,4 edge similar to the shapes in other ionic compounds like Tb2O3

  17. Friction Welding of Aluminium and Aluminium Alloys with Steel

    Directory of Open Access Journals (Sweden)

    Andrzej Ambroziak

    2014-01-01

    Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

  18. Lead inclusions in aluminium

    International Nuclear Information System (INIS)

    Ion implantation at room temperature of lead into aluminum leads to spontaneous phase separation and formation of lead precipitates growing topotactically with the matrix. Unlike the highly pressurized (∼ 1-5 GPa) solid inclusions formed after noble gas implantations, the pressure in the lead precipitates is found to be less than 0.12 GPa. Recently the authors have observed the result that the lead inclusions in aluminum exhibit both superheating and supercooling. In this paper they review and elaborate on these results. Small implantation-induced lead precipitates embedded in an aluminum matrix were studied by x-ray diffraction

  19. Uniformity of aluminium foils

    International Nuclear Information System (INIS)

    Commercially produced rolled and beaten Al foils and evaporated Al foils have been examined for thickness uniformity with an areal resolution of about 5 x 10-6 cm2 by measurements of proton backscattering yield using the Harwell microbeam facility. The evaporated Al foils were found to be uniform to better than 1% but the rolled foils were found to have non-uniformities of as much as 5-10% of their mean thickness. This is sufficient to contribute significantly to systematic errors in measurement of fast heavy ion energy straggling. (Auth.)

  20. Buffering effects on electrograining of aluminium in nitric acid

    Energy Technology Data Exchange (ETDEWEB)

    Koroleva, E.V. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom)]. E-mail: e.koroleva@umist.ac.uk; Thompson, G.E. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Skeldon, P. [Corrosion and Protection Centre, UMIST, P.O. Box 88, Manchester M60 1QD (United Kingdom); Hollrigl, G. [Alcan Technology and Management Ltd., Bad. Bahnhofstrasse 16, CH-8212 Neuhausen (Switzerland); Lockwood, S. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom); Smith, G. [Bridgnorth Aluminium Limited, Stourbridge Road, Bridgnorth WV15 6AU (United Kingdom)

    2005-09-01

    Electrograining of a binary Al-Si alloy has been undertaken in nitric acid based electrolytes, with the resultant surfaces examined by scanning and transmission electron microscopies. Depending on electrograining conditions, the pit appearance varies from hemispherical to large lateral pits, with the latter favoured in relatively acidic electrolytes. The conditions prevailing in the pit have been explored through use of aluminium ion additions to the nitric acid electrolyte as well as additions of species which influence the precipitation and dissolution of aluminium hydroxide. These confirm that control of the pit solution pH, through hydroxide generation, as a result of the selected electrograining conditions and consequent anodic and cathodic polarisation, enables tailoring of the resultant electrograined surface appearance.

  1. On the chemical and electrochemical formation of aluminium carbide in aluminium electrolysis

    OpenAIRE

    Bronislav, Novák

    2013-01-01

    Cathode wear is considered as one of the key factors for limiting the lifetime of aluminium electrolysis cells. This phenomenon has become more important as aluminium smelters have steadily increased the amperage of the cells and shifted towards graphitized cathode materials with higher electrical conductivity. The present work has focused on the fundamentals of the formation of aluminium carbide at the carbon-aluminium interface. The objective was to investigate the mechanism(s) of the forma...

  2. Aluminium Process Fault Detection and Diagnosis

    OpenAIRE

    Nazatul Aini Abd Majid; Taylor, Mark P; Chen, John J. J.; Brent R. Young

    2015-01-01

    The challenges in developing a fault detection and diagnosis system for industrial applications are not inconsiderable, particularly complex materials processing operations such as aluminium smelting. However, the organizing into groups of the various fault detection and diagnostic systems of the aluminium smelting process can assist in the identification of the key elements of an effective monitoring system. This paper reviews aluminium process fault detection and diagnosis systems and propo...

  3. A bakable aluminium vacuum chamber with an aluminium flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the construction of the vacuum chamber in proton synchrotrons and electron storage rings. (author)

  4. Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

    Energy Technology Data Exchange (ETDEWEB)

    Moe, J. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

  5. Aluminium in foodstuffs and diets in Sweden.

    Science.gov (United States)

    Jorhem, L; Haegglund, G

    1992-01-01

    The levels of aluminium have been determined in a number of individual foodstuffs on the Swedish market and in 24 h duplicate diets collected by women living in the Stockholm area. The results show that the levels in most foods are very low and that the level in vegetables can vary by a factor 10. Beverages from aluminium cans were found to have aluminium levels not markedly different from those in glass bottles. Based on the results of the analysis of individual foods, the average Swedish daily diet was calculated to contain about 0.6 mg aluminium, whereas the mean content of the collected duplicate diets was 13 mg. A cake made from a mix containing aluminium phosphate in the baking soda was identified as the most important contributor of aluminium to the duplicate diets. Tea and aluminium utensils were estimated to increase the aluminium content of the diets by approximately 4 and 2 mg/day, respectively. The results also indicate that a considerable amount of aluminium must be introduced from other sources. PMID:1542992

  6. Aluminium exclusion and aluminium tolerance in woody plants

    OpenAIRE

    Ivano eBrunner; Christoph eSperisen

    2013-01-01

    The aluminium (Al) cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion...

  7. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...

  8. Preparation of aluminium lakes by electrocoagulation

    Directory of Open Access Journals (Sweden)

    Prapai Pradabkham

    2008-07-01

    Full Text Available Aluminium lakes have been prepared by electrocoagulation employing aluminium as electrodes. The electrocoagulation is conducted in an aqueous alcoholic solution and is completed within one hour. The dye content in the lake ranges approximately between 4-32%.

  9. Regularities in aluminium and indium chemisorption on chelating polymeric sorbents

    International Nuclear Information System (INIS)

    Complexation properties of synthesized polymer chelate sorbents: substituted of polystyrene-azo-pyrocatechol are investigated and correlations between pK'OH of functional groups of sorbents as well as pH50 values of chelation and constants of stability (lgKstab) are established for studying regularities of effect of structure and acid-base properties of functional groups of sorbents on the parameters of Al3+ and In3+ chemical sorption. Established correlations make it possible to predict the physicochemical parameters of sorbents and sorption of metal ions with the aim of separation and concentration of aluminium and indium micro account from the objects of different origin

  10. Recent developments in advanced aircraft aluminium alloys

    International Nuclear Information System (INIS)

    Highlights: • To compete with composites, performance of aluminium alloys should be increased. • Al–Li alloys have higher strength, fracture and fatigue/corrosion resistance. • Improvements of aerospace Al alloys are due to optimised solute content and ratios. • In selecting new materials, there should be no reduction in the level of safety. • The use of hybrid materials could provide additional opportunities for Al alloys. - Abstract: Aluminium alloys have been the primary material for the structural parts of aircraft for more than 80 years because of their well known performance, well established design methods, manufacturing and reliable inspection techniques. Nearly for a decade composites have started to be used more widely in large commercial jet airliners for the fuselage, wing as well as other structural components in place of aluminium alloys due their high specific properties, reduced weight, fatigue performance and corrosion resistance. Although the increased use of composite materials reduced the role of aluminium up to some extent, high strength aluminium alloys remain important in airframe construction. Aluminium is a relatively low cost, light weight metal that can be heat treated and loaded to relatively high level of stresses, and it is one of the most easily produced of the high performance materials, which results in lower manufacturing and maintenance costs. There have been important recent advances in aluminium aircraft alloys that can effectively compete with modern composite materials. This study covers latest developments in enhanced mechanical properties of aluminium alloys, and high performance joining techniques. The mechanical properties on newly developed 2000, 7000 series aluminium alloys and new generation Al–Li alloys are compared with the traditional aluminium alloys. The advantages and disadvantages of the joining methods, laser beam welding and friction stir welding, are also discussed

  11. Shot peening of aluminium alloys

    International Nuclear Information System (INIS)

    Shot peening is a process of cold-hammering where a metallic surface is pelted with spherical grains. Each grain bumping into the surface acts as a hammer head and creates a small crater. The overlapping of these craters produces a residual compression layer just underneath the surface. It is well known that cracks cannot spread in a compression zone. In most cases of fatigue rupture and stress corrosion cracks propagate from the surface towards the inside so shot peening allows a longer lifetime of castings. Moreover most materials present a better resistance due to the cold-hammering effect of shot peening. Metallic surfaces can be treated in workshops or directly on site. Typical pieces that undergo shot peening on site are storing tanks, gas and steam turbines, tubes of steam generators and piping in oil or nuclear or chemical industries. This article describes shot peening from a theoretical and general point of view and presents the application to aluminium-lithium alloys. In the case of aluminium alloys shot peening can be used to shape the piece (peen-forming). (A.C.)

  12. Method for aluminium dross utilization

    International Nuclear Information System (INIS)

    A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al2O3. The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80oC. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al2O3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm3, pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

  13. Eu(III)-doped aluminium yttrium oxide

    International Nuclear Information System (INIS)

    In this work, we report the synthesis and the photoluminescence features of Eu(III)-doped yttrium-aluminium oxide obtained by non-hydrolytic sol-gel routes. After heating the powders above 600 deg C the XRD patterns show the presence of the Y4Al2O9 (YAM) and Y3Al5O12 (YAG) phases. At 800 and at 1500 deg C the PL spectra display the Eu(III) lines characteristic of the YAM monoclinic phase. The 5D0→7F2 transition is favored relatively to the 5D0→7F1 lines. However, at 1100 deg C the cubic YAG is the preferential phase and the 5D0→7F1 transition dominates the spectrum. The Eu(III) ions lie in a centro symmetrical site. The different solvents used in the sol-gel synthesis also change the relative proportion between these two phases. This is monitored analyzing the modifications in the relative intensity between the 5D0→7F2 and the 5D0→7F1 transitions. (author)

  14. Determination of lithium in lithium-aluminium alloy by capillary electrophoresis

    International Nuclear Information System (INIS)

    A simple and rapid method for the determination of lithium in lithium-aluminium alloy using capillary electrophoresis (CE) is developed. The method separates Li from other metal ions and it does not require prior separation of aluminium, which is major constituent of the alloy. Separation of Li was achieved using BGE of 20mM Imidazole (pH 2) with an applied voltage of 20kV. The precision of the method is better than 10% at 0.5 ppm of Li and LOD is 0.12 ppm. (author)

  15. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  16. Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

    Science.gov (United States)

    Grove, C. A.; Judd, G.; Ansell, G. S.

    1972-01-01

    Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

  17. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid;

    2014-01-01

    -life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a...... monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of...

  18. Laser-Doping through Anodic Aluminium Oxide Layers for Silicon Solar Cells

    Directory of Open Access Journals (Sweden)

    Pei Hsuan Doris Lu

    2015-01-01

    Full Text Available This paper demonstrates that silicon can be locally doped with aluminium to form localised p+ surface regions by laser-doping through anodic aluminium oxide (AAO layers formed on the silicon surface. The resulting p+ regions can extend more than 10 μm into the silicon and the electrically active p-type dopant concentration exceeds 1020 cm−3 for the first 6-7 μm of the formed p+ region. Anodic aluminium oxide layers can be doped with other impurities, such as boron and phosphorus, by anodising in electrolytes containing the extrinsic impurities in ionic form. The ions become trapped in the formed anodic oxide during anodisation, therefore enabling the impurity to be introduced into the silicon, with aluminium, during laser-doping. This codoping process can be used to create very heavily doped surface layers which can reduce contact resistance on metallisation, whilst the deeper doping achieved by the intrinsic aluminium may act to shield the surface from minority carriers. laser-doping through AAO layers can be performed without introducing any voids in the silicon or fumes which may be harmful to human health.

  19. Aluminium Process Fault Detection and Diagnosis

    Directory of Open Access Journals (Sweden)

    Nazatul Aini Abd Majid

    2015-01-01

    Full Text Available The challenges in developing a fault detection and diagnosis system for industrial applications are not inconsiderable, particularly complex materials processing operations such as aluminium smelting. However, the organizing into groups of the various fault detection and diagnostic systems of the aluminium smelting process can assist in the identification of the key elements of an effective monitoring system. This paper reviews aluminium process fault detection and diagnosis systems and proposes a taxonomy that includes four key elements: knowledge, techniques, usage frequency, and results presentation. Each element is explained together with examples of existing systems. A fault detection and diagnosis system developed based on the proposed taxonomy is demonstrated using aluminium smelting data. A potential new strategy for improving fault diagnosis is discussed based on the ability of the new technology, augmented reality, to augment operators’ view of an industrial plant, so that it permits a situation-oriented action in real working environments.

  20. Deformation features of aluminium in tensile tests

    International Nuclear Information System (INIS)

    It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 4000C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.)

  1. Investigation & Analysis of Different Aluminium Alloys t

    OpenAIRE

    Nibedita Sethi*¹,; Ajit Senapati²

    2014-01-01

    Aluminium alloy LM-29, A-356 AND A-6060 was fabricated in sand casting method. Mach inability of aluminium alloy LM-29, A-356 AND A-6060 was investigated and evaluate the mach inability studying the different parameter such as cutting force, surface roughness, chip thickness, and power consumption during turning at different cutting speed and constant depth of cut and feed rate. In this paper also studies the mechanical properties means hardness, density and tensile strength o...

  2. Corrosion behaviour of aluminium plates in aqueous medium

    International Nuclear Information System (INIS)

    The process of corrosion concerning the aluminium 1050 plate was studied at room temperatures, 45 and 600C in deionized water, the same Argonauta Reactor Water. Beyond the temperature influence, it was verified the effect of chloride ion and oxygen. It ws found that the amount of oxyde formed at room temperatures is almost negligible; at 45 and 600C the samples were covered with bayerita, the quantity of oxide formed at 450C being higher than at 600C. It was observed that there will be risk of corrosion in the case of Reactor Water to undergo contamination with chloride ions. The results have shown that the material can be used since the medium don't be strongly oxidizing. At potentials higher than - 900M sup(V) ess (-280 m sup(V) sub(H)), the material will undergo pitting corrosion. (Author)

  3. Doped aluminium based spinels synthesized by a soft chemistry method

    International Nuclear Information System (INIS)

    Structural and optical properties of (Co0.01Zn0.99)Al2O4 and Zn(Al1.99Ln0.01)O4 (where Ln(III) = Eu(III), Tb(III)) spinels obtained by a variant of the complexation method-tartarate route were studied. The tartarate precursors have been characterized by IR, UV-vis and luminescence spectroscopy. The doped aluminium based spinels have been investigated by X-ray diffraction (XRD), transsmision electron microscopy (TEM), infrared spectroscopy (IR), ultraviolet visible spectroscopy (UV-vis) and luminescence spectroscopy. Pure spinel nanometer powders were obtained. Under excitation at 380 nm the nanoparticles exhibits strong luminescence corresponding to 5D0 → 7F2 transition of Eu3+ ions and respectively, to 5D4 → 7Fj (j = 3, 4, 5, 6) transition of Tb3+ ions. No blue emission from the 5D3 state were observed.

  4. Removal of fluoride from water using aluminium containing compounds

    Institute of Scientific and Technical Information of China (English)

    M. Karthikeyan; K. P. Elango

    2009-01-01

    Batch adsorption studies were undertaken to assess the suitability of aluminium titanate (AT) and bismuth aluminate (BA) to remove fluoride ions from water.The effect of pH,dose of adsorbent,contact time,initial concentration,co-ions and temperature on fluoride removal efficiency were studied.The amounts of fluoride ions adsorbed,at 30℃ from 4 mg/L of fluoride ion solution,by AT and BA are 0.85 and 1.55 mg/g,respectively.The experimental data fitted well to the Freundlich and Langmuir isotherms.Thermodynamic parameters such as △H~0,△S~0 and △G~0 indicated that the removal of fluoride ions by AT is exothermic and non-spontaneous while that by BA is endothermic and spontaneous.Furrier transform infrared (FT-IR) analysis and X-ray diffraction (XRD) patterns of the adsorbent before and after adsorption indicated that fluoride ions are chemisorbed by these adsorbents.

  5. Removal of aluminium from drinking water

    International Nuclear Information System (INIS)

    Aluminium in drinking water comes from natural sources and the alum used as coagulant in the water treatment process. Exposure to aluminium has been implicated in dialysis dementia, Parkinson and Alzheimer's disease. Drinking water containing aluminium was considered to be one of the main sources of Al intake into human body. For this reason, the removal of aluminium from drinking water is vital to our health. In this study, removal of aluminium was carried out by using a chelating resin. To achieve the purpose, two chelating resin iontosorb oxin (IO) and poly hydroxamic acid (PHA) were used. The effects of concentration, pH, stirring time and resin amount was investigated. The concentration range varied between 10 and 500 ppb, pH range was between 2 and 12, stirring time between 5 and 60 minutes, and resin amount between 100 and 1500 mg. The optimum conditions of these resins were determined in a batch system. The results obtained showed that the optimum condition to remove aluminium for poly hydroxamic acid and iontosorb was pH 5-8 and pH 4-9; concentration range between 50-500 ppb, and 150-500 ppb, resin amount 200 mg and the stirring time was 20 minutes, respectively. (author)

  6. Ongoing characterization of passivated aluminium nanopowders

    Energy Technology Data Exchange (ETDEWEB)

    Kwok, Q.S.M.; Fouchard, R.C.; Turcotte, A-M.; Abdel-Qader, Z.; Jones, D.E.G. [Natural Resources Canada, CANMET, Canadian Explosives Research Laboratory, Ottawa, ON (Canada)

    2002-04-01

    For characterization, the thermal behaviour of two aluminium nanopowders - Alss and Alssef - in air was determined using differential scanning calorimetry (DSC), simultaneous thermogravimetry-DTA (TG-DTA) and accelerating rate calorimetry (ARC). Alss and Alssef were found to be less reactive to air than previously determined for Als And Alex, possibly due to their thicker and different type of passivating layer. Stability determination for Alss and Alssef in a wet oxidizing environment was carried out using ARC, whereas outgassing behaviour of mixtures of ammonium dinitramide (ADN) and the various aluminium powders was investigated using TG-DTA-FTIR-MS (Fourier Transform Infrared Spectrometry-Mass Spectrometry). The addition of various aluminium powders resulted in only minimal effect on the thermal stability of ADN. Electrostatic discharge, friction sensitivities of ADN and its mixtures with various aluminium powders, and thermal stability and sensitivity of mixtures of nano-sized molybdenum trioxide with aluminium nanopowders were also studied. The electrostatic discharge sensitivity of molybdenum trioxide was shown to increase by the addition of aluminium nanopowders. 23 refs., 5 tabs., 7 figs.

  7. Studies on influence of aluminium ions on the bioactivity of B{sub 2}O{sub 3}–SiO{sub 2}–P{sub 2}O{sub 5}–Na{sub 2}O–CaO glass system by means of spectroscopic studies

    Energy Technology Data Exchange (ETDEWEB)

    Mohini, G. Jagan; Krishnamacharyulu, N. [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Guntur 522 510, Andhra Pradesh (India); Department of Physics, Andhra Loyola College, Vijayawada 520 008, Andhra Pradesh (India); Sahaya Baskaran, G., E-mail: sbalc@rediffmail.com [Department of Physics, Andhra Loyola College, Vijayawada 520 008, Andhra Pradesh (India); Rao, P. Venkateswara [Physics Department, University of West Indies, Mona Campus, Kingston (Jamaica); Veeraiah, N., E-mail: nvr8@rediffmail.com [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Guntur 522 510, Andhra Pradesh (India)

    2013-12-15

    Bioactive multi component glasses of the composition of 27.4 B{sub 2}O{sub 3}–6.4 SiO{sub 2}–2.5 P{sub 2}O{sub 5}–25.5 Na{sub 2}O–(38.2 − x) CaO: x Al{sub 2}O{sub 3} (x between 0 and 3.2) were synthesized, by melt quenching technique and their bioactivity was investigated as a function of Al{sub 2}O{sub 3} concentration. Initially, optical absorption and infrared spectra were recorded and analyzed in order to have some pre-understanding over structural aspects of the glasses. For understanding the bioactivity, the samples were immersed in simulated body fluid (SBF) solution for prolonged times (∼30 days) and the weight loss measurements were carried out. The spectroscopic studies were repeated on the post immersed samples. From the comparison of the analysis of the spectroscopic data of both pre-immersed and post-immersed samples together with the information on variation of pH value of residual solution as a function of immersion time, it is concluded that the participation of aluminium ions in tetrahedral positions is hindrance for the formation of HA layer and for the bioactivity of the samples.

  8. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    International Nuclear Information System (INIS)

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H2PO4− ions to HPO32− ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm−2 and 1.77 mW cm−2, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for bioelectronic applications. • Selective

  9. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Slaughter, Gymama, E-mail: gslaught@umbc.edu; Sunday, Joshua; Stevens, Brian

    2015-08-01

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H{sub 2}PO{sub 4}{sup −} ions to HPO{sub 3}{sup 2−} ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm{sup −2} and 1.77 mW cm{sup −2}, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for

  10. Aluminium exclusion and aluminium tolerance in woody plants

    Directory of Open Access Journals (Sweden)

    Ivano eBrunner

    2013-06-01

    Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

  11. Heat treatment of aluminium strip coils; Gluehbehandlung von Aluminium-Bandbunden

    Energy Technology Data Exchange (ETDEWEB)

    Schroeder, Dominik; Dambauer, Georg [LOI Thermprocess GmbH, Essen (Germany)

    2012-08-15

    Nowadays, aluminium strip coils are increasingly heat-treated in single-coil lifting hearth furnaces SCL. Flexible, individual heat treatment allows fast reactions to short term requirements for the production of aluminium strip and offers energy saving possibilities. The following report describes the advantages of single-coil hearth furnaces in terms of flexibility, energy consumption and possible configurations. (orig.)

  12. Design of welded aluminium connections (Entwurf und Berechnung von Aluminium Schweissverbindungen)

    NARCIS (Netherlands)

    Soetens, F.

    1998-01-01

    In the past two decades considerable research effort has been put into welded aluminium connections in order to better understand their structural behaviour and to up-date the design rules in the existing standards at the time [1]. Since weids in aluminium are more critical compared to steel, the ab

  13. The first experimental results on laser ion loading into superconducting ECR ion source at RIKEN

    International Nuclear Information System (INIS)

    The first experimental results on ions and neutrals injection by means of laser ablation from metal targets into the RIKEN 18 GHz superconducting electron cyclotron resonance ion source (SC ECRIS) are presented. Pulsed aluminium ion currents up to Al8+ were generated in the source. The difference in pulse shapes of various charge states of the extracted ion currents is registered

  14. Aluminium as heating fuel. Tests with aluminium powder prove suitability in principle. Aluminium als Heizungs-Brennstoff. Versuche mit Aluminiumpulver beweisen prinzipielle Eignung

    Energy Technology Data Exchange (ETDEWEB)

    Weber, R.

    1990-12-01

    Tests prove that aluminium powder is perfectly suited as fuel and storage material for solar energy. The combustion product itself is again the base material for aluminium production, i.e. aluminium can be recycled. There are three problematic areas: 1. flame stability, 2. combustion duration and 3. environmental compatibility. Further development projects will aim at the construction of practice-orientated plants in which combustion, heat extraction and recovery of aluminium oxide is combined. A further aim is the melting burner to which aluminium is supplied in form of wires, cuttings or rods. (BWI).

  15. Synthesis and characterization of Aluminium and Lanthanum hydro-complexes by multinuclear NMR; Sintese e caracterizacao de hidroxocomplexos de AI e La por RMN multinuclear

    Energy Technology Data Exchange (ETDEWEB)

    Leite, Sidnei Quezada M.; Dieguez, Lidia C. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia; San Gil, Rosane A.S. [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Quimica

    1997-12-31

    Evidence suggest that the presence of Lanthanum ions in aluminium chloride solutions during base addition cause the formation of complexes which can promote the formation of an unknown macro-cation. These compounds when mixed to smectites are supposed to yield materials of high thermal stability. In order to contribute to the study of this phenomenon, aqueous solutions of aluminium and lanthanum were analysed by nuclear magnetic resonance. The methodology is presented. Results are presented 5 refs., 2 figs., 2 tabs.

  16. Luminescence characterisation of aluminium and erbium tris (8-hydroxyquinoline)

    International Nuclear Information System (INIS)

    This thesis presents the results of a study of the photoluminescence and electroluminescence in aluminium and erbium tris(8-hydroxyquinoline). It is shown that the luminescence of aluminium tris(8-hydroxyquinoline) (AlQ) originates from three distinct energy levels each of which has its own characteristic emission spectrum. The transfer of energy between each of the levels as a function of temperature has been empirically modelled using a rate equation approach. The emission from one of these levels is due to the radiative recombination of singlet excitons. The emission from the other two levels is thought to be due to radiative recombination of triplet excitons. The study of the luminescence of erbium tris(8-hydroxyquinoline) (ErQ) shows that it is possible to get energy transfer from the ligands of the molecule into the erbium ion. Characteristic emission is then obtained from the erbium ion at 1.5 μm along with emission originating from the ligands. As with AlQ there is evidence of distinct levels being responsible for the ligand emission in ErQ. Stark splitting of the luminescence due to the local electric field surrounding the Er3+ ion is also presented. These results imply that like AlQ there are two isomers of the ErQ molecule, but following sublimation one of these isomers is much more abundant than the other. Given that AlQ based OLEDs have been fabricated on p type silicon, the possibility of producing a silicon compatible 1.5 μm source using this material is also discussed along with the potential applications of such a device. (author)

  17. 3-dimensional shaped aluminium foam sandwiches

    Energy Technology Data Exchange (ETDEWEB)

    Baumeister, J. [Fraunhofer-Institut fuer Fertigungstechnik und Angewandte Materialforschung, Bremen (Germany); Baumgaertner, F. [Schunk Sintermetalltechnik, Giessen (Germany); Gers, H. [Honsel AG, Meschede (Germany); Seeliger, W. [Wilhelm Karmann GmbH, Osnabrueck (Germany)

    2000-07-01

    3-dimensional shaped sandwich panels with a very high stiffness can be produced in an elegant way by combining aluminium face sheets with an aluminium foam core. For this, a mixture of aluminium powder and a foaming agent is compressed to a semi-finished product of nearly vanishing porosity by extrusion, powder rolling or hot isostatic pressing. The resulting foamable semi-finished aluminium material is roll clad with sheets of conventional sheet or aluminium. As a result a precursor material is obtained consisting of two face sheets which are metallurgically bonded to the foamable core layer. This sandwich precursor material can be shaped into a 3-dimensional part by conventional techniques, e.g. by stamping or deep drawing. In a final step the foamable precursor material is heated up to the melting point of the core layer thus initiating its expansion into the desired 3-dimensional shaped sandwich structure. The porosity of the foamed core layer is in the range from 80-90% so that the integral density of the sandwich structure can be as low as 0,7 g/cm{sup 3}. The sandwich materials combine the low weight and high bending stiffness with the advantages of the face sheets, i.e. the high strength and weldability. The manufacturing process will be described in detail and the material properties will be shown. Current and future possible applications will be outlined as well as concrete parts produced up to date. (orig.)

  18. Effect of aluminium phosphate as admixture on oxychloride cement

    Indian Academy of Sciences (India)

    M P S Chandrawat; R N Yadav

    2000-02-01

    The effect of admixing of aluminium phosphate on oxychloride cement in the matrix has been investigated. It is shown that aluminium phosphate retards the setting process of the cement and improves water-tightness.

  19. Solidification of spent TBP solvent with aluminium chloride compounds

    International Nuclear Information System (INIS)

    The new techniques for processing spent TBP was investigated. It was proved that treatment of TBP containing DBP with aluminium chloride resulted in the formation of aluminium phosphate suitable for long term storage and final disposal

  20. Steam Assisted Accelerated Growth of Oxide Layer on Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Yuksel, Serkan; Jellesen, Morten Stendahl; Møller, Per; Ambat, Rajan

    2013-01-01

    Corrosion resistance of aluminium alloys is related to the composition and morphology of the oxide film on the surface of aluminium. In this paper we investigated the use of steam on the surface modification of aluminium to produce boehmite films. The study reveals a detailed investigation of the...... effect of vapour pressure, structure of intermetallic particles and thickness of boehmite films on the corrosion behaviour of aluminium alloys....

  1. Advances in development and application of aluminium batteries

    DEFF Research Database (Denmark)

    Qingfeng, Li; Zhuxian, Qiu

    2001-01-01

    Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation of...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

  2. Friction stir welding (FSW) of aluminium foam sandwich panels

    OpenAIRE

    M. Bušić; Kožuh, Z.; D. Klobčar; Samardžić, I.

    2016-01-01

    The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and f...

  3. Study on hardening mechanisms in aluminium alloys

    Directory of Open Access Journals (Sweden)

    P. K. Mandal

    2016-01-01

    Full Text Available The Al-Zn-Mg alloys are most commonly used age-hardenable aluminium alloys. The hardening mechanism is further enhanced in addition of Sc. Sc additions to aluminium alloys are more promising. Due to the heterogeneous distribution of nano-sized Al3Sc precipitates hardening effect can be accelerated. Mainly, highlight on hardening mechanism in Al-Zn-Mg alloys with Sc effect is to study. In addition, several characterisations have been done to age-hardening measurements at elevated temperatures from 120oC to 180 oC. The ageing kinetics has also been calculated from Arrhenius equation. Furthermore, friction stir processing (FSP can be introduced to surface modification process and hardened the cast aluminium alloys. In this study, hardening mechanism can be evaluated by Vicker’s hardness measurement and mechanical testing is present task.

  4. Mechanical characteristics of aluminium / aluminium and aluminium / steel joints used for lightening of automobile bodies; Caracteristiques mecaniques d'assemblages aluminium / aluminium et aluminium / acier utilises pour l'allegement des carrosseries automobiles

    Energy Technology Data Exchange (ETDEWEB)

    Kosuge, Haraga [Mitsubishi Electric Corp., Centre de R and D des Technologies Avancees, Dept. des Materiaux et des Eco-Materiaux (Japan)

    2001-06-01

    All the possible solutions used for the steel-aluminium composite bonds are not equal. The riveting, linked or not to the bonding, give the best results. The clinching requires an increase of thicknesses for a mechanical resistance equal to those of homogeneous joints. (O.M.)

  5. Ion beam preparation: an excellent instrument for the characterization of the byproducts of the melt powder metallurgical aluminium foam process; Ionenstrahlpraeparation: Ein treffliches Werkzeug zur Charakterisierung der Zwischenprodukte des schmelzpulvermetallurgischen Aluminiumschaeumverfahrens

    Energy Technology Data Exchange (ETDEWEB)

    Hoehn, S.; Obenaus, P. [Fraunhofer-Institut fuer Keramische Technologien und Systeme (IKTS), Dresden (Germany); Hohlfeld, J.; Lies, C. [Fraunhofer-Institut fuer Werkzeugmaschinen und Umformtechnik (IWU), Chemnitz (Germany)

    2008-03-15

    The goal of the investigations was to develop the basic knowledge of the micro-structural changes in the technological process of the production of metal foam by the melt powder metallurgical process. An exact characterization of the grain structure was necessary for all technological stages. The usual metallographic preparations were not possible due to the highly volatile components of the expanding agent as well as the lightly pressed powders having contrasting properties. This article explores the possibilities of ion beam preparation in which the grain structure and, in particular, the propellant can be represented exactly in all technological stages (powder mixture, compact, extrusion, metal foam). (orig.)

  6. Eletrodo íon-seletivo para determinação potenciométrica de alumínio(III) em meio de fluoreto Ion-selective electrode for potentiometric determination of aluminium(III) in fluoride medium

    OpenAIRE

    Evandro Piccin; Orlando Fatibello-Filho; Luiz Antonio Ramos

    2004-01-01

    The construction and analytical evaluation of a coated graphite Al(III) ion-selective electrode, based on the ionic pair formed between the Al(F)n3-n anion and tricaprylylmethylammonium cation (Aliquat 336S) incorporated on a poly(vinylchloride) (PVC) matrix membrane are described. A thin membrane film of this ionic pair and dibutylphthalate (DBPh) in PVC was deposited directly on a cylindric graphite rod (2 cm length x 0.5 cm diameter) attached to the end of a glass tube using epoxy resin. T...

  7. Corrosion behaviour of borated aluminium used as neutron absorber

    International Nuclear Information System (INIS)

    The electrochemical behaviour of pure and borated aluminium was examined. Measurements were performed in two different electrolytes at 90 C containing different trace-amounts of chloride. For borated aluminium current transients, i.e. metastable depassivation events were found. It is suggested to attribute these transients to less stable passivation layers in comparison to pure aluminium

  8. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    OpenAIRE

    B. Bobic; Mitrovic, S.; M. Babic; I. Bobic

    2010-01-01

    The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion) was discussed. Some corrosion protection methods of aluminium based MMCs were described

  9. Internal friction in iron-aluminium alloys having a high aluminium content

    International Nuclear Information System (INIS)

    By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author)

  10. Diamond grooving of rapidly solidified optical aluminium

    Science.gov (United States)

    Abou-El-Hossein, Khaled; Hsu, Wei-Yao; Ghobashy, Sameh; Cheng, Yuan-Chieh; Mkoko, Zwelinzima

    2015-10-01

    Traditional optical aluminium grades such as Al 6061 are intensively used for making optical components for applications ranging from mould insert fabrication to laser machine making. However, because of their irregular microstructure and relative inhomogeneity of material properties at micro scale, traditional optical aluminium may exhibit some difficulties when ultra-high precision diamond turned. Inhomogeneity and micro-variation in the material properties combined with uneven and coarse microstructure may cause unacceptable surface finish and accelerated tool wear, especially in grooving operation when the diamond tool edge is fully immersed in the material surface. Recently, new grades of optical aluminium that are featured by their ultra-fine microstructure and improved material properties have been developed to overcome the problem of high tool wear rates. The new aluminium grades have been developed using rapid solidification process which results in extremely small grain sizes combined with improved mechanical properties. The current study is concerned with investigating the performance of single-point diamond turning when grooving two grades of rapidly solidified aluminium (RSA) grades: RSA905 which is a high-alloyed aluminium grade and RSA443 which has a high silicon content. In this study, two series of experiments employed to create radial microgrooves on the two RSA grades. The surface roughness obtained on the groove surface is measured when different combinations of cutting parameters are used. Cutting speed is varied while feed rate and depth of cut were kept constant. The results show that groove surface roughness produced on RSA443 is higher than that obtained on RSA905. Also, the paper reports on the effect of cutting speed on surface roughness for each RSA grade.

  11. Screen-printed platinum electrodes for measuring crevice corrosion: Nickel aluminium bronze as an example

    OpenAIRE

    Cranny, Andrew; Harris, Nick; Lewis, Adam; Nie, Menyang; Wharton, Julian; Wood, Robert; Stokes, Keith

    2010-01-01

    Screen-printed platinum electrodes were used to monitor crevice corrosion processes. The electrodes, printed on an inert alumina substrate, formed the bottom of an artificial crevice when mechanically clamped to a rectangular block of nickel-aluminium bronze (NAB). Cyclic differential pulse voltammetry was used to detect corrosion products over time whilst the assembly was immersed in a 3.5% by weight aqueous solution of sodium chloride. Cupric (Cu2+), ferric (Fe3+) and ferrous (Fe2+) ions we...

  12. Electrochemical monitoring of nickel–aluminium bronze crevice corrosion solutions using boron–doped diamond electrode

    OpenAIRE

    Neodo, Stefano

    2013-01-01

    This study has demonstrated the capability of electrochemically assessing the metal–ion concentrations generated from the localised corrosion of nickel–aluminium bronzes (NAB). Prior to investigating NAB crevice corrosion, its electrochemical properties were studied at different pHs and chloride concentrations. At solution pHs higher than 4 NAB exhibited a corrosion behaviour similar to that of unalloyed copper and its oxidation was controlled by the dissolution of the copper–rich ?–phase. Ho...

  13. Rapidly solidified aluminium for optical applications

    OpenAIRE

    Gubbels, G.P.H.; Venrooy, B.W.H.; Bosch, A.J.; Senden, R

    2008-01-01

    This paper present the results of a diamond turning study of a rapidly solidified aluminium 6061 alloy grade, known as RSA6061. It is shown that this small grain material can be diamond turned to smaller roughness values than standard AA6061 aluminium grades. Also, the results are nearly as good as nickel plated surfaces, but the RSA6061 has the advantage that no additional production steps are needed and that no bi-metallic bending or delamination can occur in a thermally changing environmen...

  14. Defect generation during solidification of aluminium foams

    International Nuclear Information System (INIS)

    The reason for the frequent occurrence of cell wall defects in metal foams was investigated. Aluminium foams often expand during solidification, a process which is referred as solidification expansion (SE). The effect of SE on the structure of aluminium foams was studied in situ by X-ray radioscopy and ex situ by X-ray tomography. A direct correlation between the magnitude of SE and the number of cell wall ruptures during SE and finally the number of defects in the solidified foams was found.

  15. The dissolution and formation enthalpy of alloys and intermetallics of aluminium-lanthanum and aluminium-cerium systems

    International Nuclear Information System (INIS)

    Present article is devoted to dissolution and formation enthalpy of alloys and intermetallics of aluminium-lanthanum and aluminium-cerium systems. Therefore the dissolution temperatures of alloys and intermetallics of aluminium-lanthanum and aluminium-cerium systems were defined by means of calorimetry method. The enthalpy of formation of intermetallics of Al-Ce system was defined as well. The regularities in changes of dissolution and formation enthalpy of alloys and intermetallics depending on composition were studied.

  16. Fundamental studies of growth mechanisms in physical vapour deposition of aluminium

    CERN Document Server

    Knorr, N J

    2000-01-01

    temperature could be independently controlled due to the low deposition rate of the aluminium. The depositions were performed in a UHV environment to ensure that film growth was not mediated by contamination. The ion energy range used was 10-75eV and the substrate temperature varied from -100 deg C to 200 deg C. The depositions were onto silicon (100) with a native oxide surface, except for a set of depositions which were performed on to silicon with the native oxide surface removed. The cleanliness of the depositions was verified using in-situ XPS analysis and after deposition the structure of the aluminium films was inferred from measurements using SEM, TEM, AFM XRD and Nano-indendation. This information allowed the mechanisms of growth of the aluminium films to be investigated. In addition to the extensive array of IBDR depositions a series of aluminium films were deposited using evaporation and sputtering. These films were grown at substrate temperatures between room temperate and 200 deg C. The use of ev...

  17. Determination of operationally defined fractions of aluminium in reference materials and acid attacked environmental samples

    International Nuclear Information System (INIS)

    The aim of the presented work is to evaluate the selectivity of the operationally defined procedures for the aluminium fractionation in the reference materials and the environmental samples affected by the mining activity. The combination of the sequential optimized BCR (European Commission Community Bureau of Reference) three-step, the single (H2O, CaCl2, Na2S2O4, NH4F (NH4)2C2O4, HCl, NTA, EDTA, DTPA) and the solid phase chelating ion-exchange extraction procedures was performed for the aluminium fractionation in the samples. The amount of the reactive Al determined by the solid phase extraction on the chelating resin Iontosorb Salicyl is the most important operationally defined fraction of aluminium from the aspect of its negative effects on the environment. The available Al concentrations obtained from the different operationally defined fractionation methods were compared. The flame atomic absorption spectrometry was used for the aluminium quantification. The X-ray diffraction analyse of the samples was performed for the mineral composition determination. The precision, the repeatability and the accuracy for the all steps of the optimized BCR sequential extraction procedure were checked on six reference materials (SRM 2710, RSS SO-2, RSS SO-4, CRM SA-B, SRM RTH 912, CRM 025-050). The precision and the repeatability were very good with the R.S.D. values 11%. The fraction specific accuracy was excellent. The new indicative fractional Al values in the used reference materials are published

  18. A study of aluminium-exposed fish using a scanning proton microprobe

    Energy Technology Data Exchange (ETDEWEB)

    Cholewa, M.; Legge, G.L.F. [Melbourne Univ., Parkville, VIC (Australia). School of Physics; Eeckhaoudt, S.; Van Grieken, R. [Universitaire Instelling Antwerpen, Antwerp (Belgium)

    1993-12-31

    A major problem has arisen in Europe with the depopulation of fresh water fish in lakes and streams collecting acid rain. The sensitivity to acidification is species specific and appears to be associated with metal levels. The Scanning Proton Microprobe (SPMP) at the Micro Analytical Research Centre of the University of Melbourne was used to study the subcellular distribution of aluminium and other elements in the gills of fish exposed to acidified water with elevated Al-levels. Experiments were performed on thin sections taken from fish exposed to media with different pH and aluminium concentration. Aluminium was found on the surface of the gill lamellae, but also inside the tissue. Bulk analysis of the gills showed much higher concentrations in the aluminium-exposed fish, compared to the control ones, but no information regarding the actual accumulation sites can be inferred. Extensive study of damage done to the sample by intense proton beams during elemental analysis was performed with scanning transmission ion microscopy. 3 refs., 3 figs.

  19. Radio frequency plasma nitriding of aluminium at higher power levels

    International Nuclear Information System (INIS)

    Nitriding of aluminium 2011 using a radio frequency plasma at higher power levels (500 and 700 W) and lower substrate temperature (500 deg. C) resulted in higher AlN/Al2O3 ratios than obtained at 100 W and 575 deg. C. AlN/Al2O3 ratios derived from X-ray photoelectron spectroscopic analysis (and corroborated by heavy ion elastic recoil time of flight spectrometry) for treatments preformed at 100 (575 deg. C), 500 (500 deg. C) and 700 W (500 deg. C) were 1.0, 1.5 and 3.3, respectively. Scanning electron microscopy revealed that plasma nitrided surfaces obtained at higher power levels exhibited much finer nodular morphology than obtained at 100 W

  20. Process evaluation for treatment of aluminium bearing declad waste

    International Nuclear Information System (INIS)

    Declad waste generated by the process of chemical decladding of Al-cladded uranium metal fuel is characterized by highly alkaline, high Al bearing intermediate level waste. It was found that the process developed and adopted in India for plant scale treatment of alkaline intermediate level waste (ILW) is unsuitable for treatment of declad waste. This is mainly due to its exotic characteristics, notably substantial amounts of aluminium in the declad waste. As part of development of treatment scheme for this waste, 137Cs removal by RFPR has been demonstrated earlier and the present paper reports the results of further processing of the Cs-lean effluent. The waste simulated with respect to the major chemical constituents of stored Al-bearing alkaline ILW after 137Cs and 90Sr removal by ion exchange, is used in this study

  1. Structure and distribution of oxides in aluminium foam

    International Nuclear Information System (INIS)

    Foaming of aluminium is investigated under oxidizing and non-oxidizing gas atmospheres. Foams were prepared by mixing and pressing Al99.95 and TiH2 powders and foaming the pressed material in a gas-tight X-ray transparent furnace while following the process by X-ray radioscopy. The structure and distribution of the oxides present in the powders, precursors and foams were studied by light microscopy, scanning and transmission electron microscopy. Sequential focused ion beam slicing was used to obtain tomographic images of oxide and micropore distributions within the individual cell walls of the foams. A complex hierarchical structure of the oxides is found. Oxides reside in the bulk of the cell walls without a pronounced segregation to the gas/metal interfaces. The presence of air retards foaming due to oxidation of the outer surface

  2. China’s Production and Market of Aluminium Extruded Profiles

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    <正>Chinese aluminium extrusion industry came into existence at the early 1950s with most products used in military industry and national defence.At the beginning of 1980s,the produc- tion of construction aluminium profiles started simultaneously in North and South China.In the following thirty years,the aluminium extru- sion industry entered into a quickly developing stage with a focus on construction aluminium profiles.With the blooming real estate industry, the demand for construction aluminium profiles from the domestic market has a tendency of yearly increase.From 2000,the quick devel- opments of China’s auto and railway vehicle

  3. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    OpenAIRE

    B. Formanek; J. Piątkowski; J. Szymszal

    2010-01-01

    Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameter...

  4. Influence of aluminium alloy type on dissimilar friction stir lap welding of aluminium to copper

    OpenAIRE

    Galvão, I; Verdera, D; Gesto, D; Loureiro, A.; Rodrigues, D. M.

    2013-01-01

    A heat-treatable (AA 6082) and a non-heat treatable (AA 5083) aluminium alloys were friction stir lap welded to copper using the same welding parameters. Macro and microscopic analysis of the welds enabled to detect important differences in welding results, according to the aluminium alloy type. Whereas important internal defects, resulting from ineffective materials mixing, were detected for the AA 5083/copper welds, a relatively uniform material mixing was detected in the AA 6082/copper wel...

  5. Decreasing methylation of pectin caused by nitric oxide leads to higher aluminium binding in cell walls and greater aluminium sensitivity of wheat roots

    OpenAIRE

    Sun, Chengliang; Lu, Lingli; Yu, Yan; Liu, Lijuan; Hu, Yan; Ye, Yiquan; Jin, Chongwei; Lin, Xianyong

    2015-01-01

    Highlight Aluminium-induced nitric oxide production enhances the aluminium sensitivity of wheat by decreasing pectin methylation of root cell-wall pectin, resulting in greater aluminium binding in root cell walls.

  6. Steam generated conversion coating on aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    into functional conversion coatings in order to enhance corrosion resistance and adhesion to paint systems. Chromium based conversion coatings have been extensively used on aluminium alloys to improve adhesion of subsequent paint layers and corrosion resistance. However, the use of hexavalent chromium...

  7. Alloys oxidation of aluminium-scandium system

    International Nuclear Information System (INIS)

    Alloys and compounds of rare earth metals with aluminium thanks to their high corrosion stability, durability and small specific weight find to apply in various new techniques. On the base of carried out investigation it could be recommend as de oxidizing and alloying compositions containing 15-50 % of scandium as in possession of minimal oxidation

  8. Constant structure creep experiments on aluminium

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel

    2011-01-01

    Roč. 49, č. 5 (2011), s. 307-318. ISSN 0023-432X R&D Projects: GA AV ČR IAA2041203 Institutional research plan: CEZ:AV0Z20410507 Keywords : mechanical properties * high temperature deformation * creep * aluminium Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.451, year: 2011

  9. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P;

    2005-01-01

    adjuvant) to pigs inoculated twice with apyrogenic bi-distilled water (group water) and to pigs inoculated once with the adjuvant and once with apyrogenic bi-distilled water (group adjuvant/water). Both studies agreed in their conclusions, which indicate that the high amount of aluminium hydroxide was the...

  10. Indentation of aluminium foam at low velocity

    Directory of Open Access Journals (Sweden)

    Shi Xiaopeng

    2015-01-01

    Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

  11. Study of the electronic structure modifications of silicon oxide (α -SiO2), aluminium oxide (α -Al2O3) and yttrium oxide (Y2O3), induced by structure defects (non-stoichiometry, mechanical stresses, heavy ion irradiation)

    International Nuclear Information System (INIS)

    We have studied ceramics, experimentally (X-ray threshold absorption, photoelectron spectroscopy) and theoretically (density of states calculations based on a tight-binding method). Three ways have been followed: - influence of oxygen stoichiometry on the electronic structure of Y2O3: we have showed the splitting of the yttrium d-orbitals (octahedral symetry site), the splitting of the K-yttrium threshold (band effect), and the splitting of the K-oxygen threshold (hybridization of the oxygen p-levels with the yttrium p and d levels in the conduction band). For the valence band, the importance of O-O interactions have been underlined. The introduction of oxygen vacancies makes the Y-O bond more covalent, so that samples are more conductive and their optical dielectric constant increases. - effect of a mechanical stress on the electronic structure of quartz (α -SiO2): - influence of a heavy ion irradiation on the electronic structure of quartz and alumina: After irradiation, quartz is in a desorganized crystalline state, different from an amorphous state. Results have been interpreted in terms of metamict state and internal mechanical stresses

  12. Technology of obtaining of cryolite and aluminium fluoride from alumina- and fluoride containing wastes of aluminium production

    International Nuclear Information System (INIS)

    This article is devoted to technology of obtaining of cryolite and aluminium fluoride from alumina- and fluoride containing wastes of aluminium production. Thus, the investigations on elaboration of technology of obtaining of cryolite and aluminium fluoride from alumina- and fluoride containing wastes of aluminium production by means of sulfuric acid decomposition method are carried out. The optimal parameters of technological processes are found. The physicochemical analysis of fluoride containing wastes is conducted. The flowsheet of obtaining of cryolite, aluminium fluoride and alumina from alumina- and fluoride containing wastes is presented.

  13. Ab initio calculation of the deprotonation constants of an atomistically defined nanometer-sized, aluminium hydroxide oligomer

    Energy Technology Data Exchange (ETDEWEB)

    Wander, Matthew C.; Shuford, Kevin L.; Rustad, James R.; Casey, William H.

    2013-03-01

    Aluminium possesses significant and diverse chemistry. Numerous compounds have been defined, and the elucidation of their chemistry is of significant geochemical interest. In this paper, a brucite-like, eight-aluminium aqueous cluster is modelled with density functional theory to identify its primary site of deprotonation and the associated pK(a) constant using both explicit (a full first solvent shell) and implicit solvent. Two methods for calculating the pK(a) are compared. We found that a bond density approach is better than a direct energy calculation for ions with large charge and high symmetry. The terminal aluminium atoms have equatorial ligated waters that in solvent have one long O-H bond. This site is more reactive than any of the other protons on the particle. Insights into the experimental crystal structure and Bader's Atoms in Molecules density analysis are presented as routes to reduce the computational time required for the identification of protonation sites.

  14. A density functional theory study of the structure of pure-silica and aluminium-substituted MFI nanosheets

    Science.gov (United States)

    Hernandez-Tamargo, Carlos E.; Roldan, Alberto; de Leeuw, Nora H.

    2016-05-01

    The layered MFI zeolite allows a straightforward hierarchization of the pore system which accelerates mass transfer and increases its lifetime as a catalyst. Here, we present a theoretical study of the structural features of the pure-silica and aluminium-substituted MFI nanosheets. We have analysed the effects of aluminium substitution on the vibrational properties of silanols as well as the features of protons as counter-ions. The formation of the two-dimensional system did not lead to appreciable distortions within the framework. Moreover, the effects on the structure due to the aluminium dopants were the same in both the bulk and the slab. The principal differences were related to the silanol groups that form hydrogen-bonds with neighbouring aluminium-substituted silanols, whereas intra-framework hydrogen-bonds increase the stability of aluminium-substituted silanols toward dehydration. Thus, we have complemented previous experimental and theoretical studies, showing the lamellar MFI zeolite to be a very stable material of high crystallinity regardless of its very thin structure.

  15. Neutron diffraction study at 0.3 K of the magnetic properties of rare-earth aluminium or gallium garnets

    International Nuclear Information System (INIS)

    In order to study ordered magnetic states below 1.5 deg. K by neutron diffraction measurements, a helium-3 cryostat has been realised in which the thermalization of a great quantity of powdered sample is performed by a helium-4 superfluid film, and which leaves the possibility of applying an external magnetic field. We thus studied essentially the magnetic phase transitions of rare-earth aluminium or gallium garnets. First we determined the antiferromagnetic structures of the erbium gallium garnet (TN = 0.79 deg. K) and of the neodymium gallium garnet (TN = 0.516 deg. K). The metamagnetic behavior of the erbium gallium garnet has been observed and compared to that of the dysprosium aluminium garnet. Second we considered the 'non-Kramers' ions Tb3+ and Ho3+ in the aluminium garnets. In this case, only two single ground states (well isolated from upper levels) have to be considered. A molecular field model with purely magnetic dipolar interactions, leads then to the existence of magnetic phase transition with antiferromagnetic ordering. This has been observed for the terbium-aluminium garnet below TN 1.35 deg. K and for the holmium-aluminium garnet below TN ∼ 0.98 deg. K. (author)

  16. Evidence of dilute ferromagnetism in rare-earth doped yttrium aluminium garnet

    International Nuclear Information System (INIS)

    This work demonstrates strong coupling regime between an erbium ion spin ensemble and microwave hybrid cavity-whispering gallery modes in a yttrium aluminium garnet dielectric crystal. Coupling strengths of 220 MHz and mode quality factors in excess of 106 are demonstrated. Moreover, the magnetic response of high-Q modes demonstrates behaviour which is unusual for paramagnetic systems. This behaviour includes hysteresis and memory effects. Such qualitative change of the system's magnetic field response is interpreted as a phase transition of rare earth ion impurities. This phenomenon is similar to the phenomenon of dilute ferromagnetism in semiconductors. The clear temperature dependence of the phenomenon is demonstrated

  17. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part I Microstructural investigation

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Piotrowska, Kamila; Gudla, Visweswara Chakravarthy;

    2015-01-01

    The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment ...... particles resulting in poor coverage by the steam generated oxide layer compared to the coating formed using MnO4−ions. Further, increase in the concentration of NO3−ions in the solution retards precipitation of the steam generated aluminium hydroxide layer.......The surface treatment of aluminium alloys under steam containing KMnO4 and HNO3resulted in the formation of an oxide layer having a thickness of up to 825 nm. The use of KMnO4 and HNO3 in the steam resulted in incorporation of the respective chemical species into the oxide layer. Steam treatment...

  18. The first data from the Orion laser: measurements of the spectrum of hot dense aluminium

    Science.gov (United States)

    Hoarty, D. J.; Allan, P.; James, S. F.; Brown, C. R. D.; Hobbs, L. M. R.; Hill, M. P.; Harris, J. W. O.; Morton, J.; Brookes, M. G.; Shepherd, R.; Dunn, J.; Chen, H.; Von Marley, E.; Beiersdorfer, P.; Chung, H. K.; Lee, R. W.; Brown, G.; Emig, J.

    2016-03-01

    The newly commissioned Orion laser system has been used to study dense plasmas created by a combination of short pulse laser heating and compression by laser driven shocks. Thus the plasma density was systematically varied between 1 and 10g/cc by using aluminium samples buried in plastic foils or diamond sheets. The aluminium was heated to electron temperatures between 500eV and 700eV allowing the plasma conditions to be diagnosed by K- shell emission spectroscopy. The K-shell spectra show the effect of the ionization potential depression as a function of density via the delocalization of n=3 levels and disappearance of n=3 transitions in He-like and H-like aluminium. The data are compared to simulated spectra, which account for the change in the ionization potential by the commonly used Stewart and Pyatt prescription; a simple ion sphere model and an alternative due to Ecker and Kroll suggested by recent X-ray free-electron laser experiments. The experimental data are in reasonable agreement with the model of Stewart and Pyatt, but are in better agreement with a simple ion sphere model. The data indicate that the Ecker and Kröll model overestimates substantially the ionization potential depression in this regime.

  19. The rechargeable aluminum-ion battery

    KAUST Repository

    Jayaprakash, N.

    2011-01-01

    We report a novel aluminium-ion rechargeable battery comprised of an electrolyte containing AlCl3 in the ionic liquid, 1-ethyl-3-methylimidazolium chloride, and a V2O5 nano-wire cathode against an aluminium metal anode. The battery delivered a discharge capacity of 305 mAh g-1 in the first cycle and 273 mAh g-1 after 20 cycles, with very stable electrochemical behaviour. © The Royal Society of Chemistry 2011.

  20. Lattice site occupation of insoluble impurity atoms in aluminium after implantation and irradiation

    International Nuclear Information System (INIS)

    Several elements, whose atoms are oversized and insoluble in aluminium, were implanted in aluminium single crystals at different temperatures. The substitutional fraction and the lattice site location were determined using the ion-channeling technique. The substitutional fractions obtained by in situ analyses are strongly dependent on the implantation temperature. At implantation and analysis temperatures below the temperature of stage III the substitutional fraction is significant larger than at temperatures above. With increasing heat of solution the substitutional fraction decreases for all implantation temperatures. The nonsubstitutional component consists of impurity atom-vacancy complexes. These complexes are formed in the cooling phase of the cascade. At temperatures above the temperature of stage III additional free mobile vacancies were captured by the impurity atoms. The capture radius is correlated with the heat of solution and the size mismatch energy. The results constitute for the first time an experimental confirmation of molecular dynamics calculations of cascade evolution. (orig./BHO)

  1. Steam assisted oxide growth on aluminium alloys using oxidative chemistries: Part II corrosion performance

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-01-01

    Surface treatment of aluminium alloys using steam with oxidative chemistries, namely KMnO4 and HNO3 resulted in accelerated growth of oxide on aluminium alloys. Detailed investigation of the corrosion performance of the treated surfaces was carried out using potentiodynamic polarisation and...... standard industrial test methods such as acetic acid salt spray (AASS) and filiform corrosion on commercial AA6060 alloy. Barrier properties of the film including adhesion were evaluated using tape test under wet and dry conditions. Electrochemical results showed reduced cathodic and anodic activity, while...... the protection provided by steam treatment with HNO3was a function of the concentration of NO3−ions. The coating generated by inclusion of KMnO4showed highest resistance to filiform corrosion. Overall, the performance of the steam treated surfaces under filiform corrosion and AASS test was a result of...

  2. Growth of L-Valinium Aluminium Chloride single crystal for OLED and super-capacitor applications

    Science.gov (United States)

    Kalaivani, D.; Vijayalakshmi, S.; Theras, J. Elberin Mary; Jayaraman, D.; Joseph, V.

    2015-12-01

    L-Valinium Aluminium Chloride (LVAC), a novel semi-organic material, was grown using slow evaporation under isothermal condition. The single crystal data reveal that the grown crystal belongs to monoclinic system. The SEM micrographs give clear picture about the surface morphology. Further, they confirm the inclusion of aluminium chloride into atomic sites of L-Valine. The compositional elements present in the crystal were identified through EDAX analysis. The mass spectral analysis was carried out to determine the molecular weight of the grown crystal. The optical transparency of the grown crystal was investigated by UV-vis-NIR spectrum. FTIR spectral study was used to identify the functional groups present in the grown material. The luminescence characteristics of grown material were analysed to confirm the effect of metal ion on the ligand. This property makes the material suitable for OLED application. The supercapacitive performance of the grown crystal was finally studied using cyclic voltammetry.

  3. Steam Initiated Surface Modification of Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud

    detailed analysis of the structure and morphology of the coating, and interface structure with and without organic top coat. Corrosion performance of the coatings was investigated using electrochemical methods, AASS, and FFC test. The morphology, microstructure, chemical composition, adhesion, and......The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes......-friendly alternative processes. In the present work high temperature steam-based process has been investigated as a possible chromate free conversion coating. Investigations in the thesis includes the effect of alloy type, substrate microstructure, surface finish, and various chemistries on the coating formation, and...

  4. FSW characterization of 6082 aluminium alloys sheets

    OpenAIRE

    K. Mroczka; A. Pietras

    2009-01-01

    Purpose: The purpose of the investigations was to elaborate a set of FSW parameters for connecting 6082 aluminium alloy sheets allowing to produce welds of highest strength.Design/methodology/approach: The FSW was tried at different speeds and at additional cooling. The welds microstructure was studied using optical and scanning electron microscopes. The mechanical properties of produced connections are discussed regarding their tensile test and microhardness measurements.Findings: The FSW we...

  5. Aluminium-based Coatings for Cadmium Replacement

    OpenAIRE

    Cardilli , Emanuele

    2008-01-01

    Cadmium electroplating is widely used in the aerospace industry for the corrosion protection of high strength steels. Cadmium is also used as compatible coating to reduce the galvanic corrosion generated in the assembly of components manufactured with different materials. However, environmental and safety concerns over the high toxicity of cadmium has led to the investigation of suitable replacements. Aluminium coatings are promising coatings for the replacement of electropl...

  6. Aluminium matrix composites fabricated by infiltration method

    OpenAIRE

    L.A. Dobrzański; M. Kremzer; A. J. Nowak; Nagel, A.

    2009-01-01

    Purpose: The aim of this work is to examine the structure and properties of metal matrix composites obtained by infiltration method of porous ceramic preforms by liquid aluminium alloy.Design/methodology/approach: Ceramic preforms were manufactured by the sintering method of ceramic powder. The preform material consists of powder Condea Al2O3 CL 2500, however, as the pore forming the carbon fibers Sigrafil C10 M250 UNS were used. Then ceramic preforms were infiltrated with liquid eutectic EN ...

  7. Quantitative evaluation of the aluminium titanate formation

    International Nuclear Information System (INIS)

    Samples of aluminium titanate were obtained under isothermal sintering condition in equimolar Al2 O3 Ti O2 powder mixtures at different soaking time intervals. The formation of Al2 Ti O5 and the effect of Si O2 additive in the reaction and densification were analysed. Quantitative evaluation of Al2 Ti O5 was performed by the Rietveld method and by using an internal standard. Both methods were considered appropriated for the presented purpose. (author)

  8. Methods of inoculation of pure aluminium structure

    Directory of Open Access Journals (Sweden)

    J. Szajnar

    2008-03-01

    Full Text Available Purpose: The main aim of investigations was the reduction of grain size and unification of structure for pure Al casting by introduction of small amount of inoculant (less than obligatory standart PN-EN 573-3, which concerning about aluminium purity, with electromagnetic field and variable casting parameters.Design/methodology/approach: To investigations it was used light microscopy and TEM. Surfaces of samples which were prepared for macro- and microstructure analysis were etched with use of solution of: 50g Cu, 400ml HCl, 300ml HNO3 and 300ml H2O. Thin foils for TEM investigations were electropolished with use of 20 ml HClO4 and 80ml CH3OH.Findings: The results of investigations and their analysis show possibility of effective inoculation of pure aluminium structure by use of some factors such as: different materials of the mould, influencing of stirring electromagnetic field into metal during solidification, inoculation by introducing AlTi5B1 inoculant into liquid aluminium and changing the pouring temperature.Research limitations/implications: I further research, authors of this paper are going to application of introduced method of inoculation in industrial tests.Practical implications: The work presents refinement of structure method which are particularly important in continuous and semi – continuous casting where products are used for plastic forming. Large columnar crystals zone result in forces extrusion rate reduction and during the ingot rolling delamination of external layers can occur. Thus, in some cases ingot skinning is needed, which rises the production costs.Originality/value: Contributes to research on size reduction in pure aluminium structure.

  9. Perforation of aluminium alloy thin plates

    OpenAIRE

    ANTOINAT, Léonard; Kubler, Régis; BAROU, Jean Luc; VIOT, Philippe; BARRALLIER, Laurent

    2015-01-01

    Low velocity perforation of aeronautical aluminium alloy sheets 2024 T3 is studied in this paper. After a literature review on recent experiments and models of plate’s perforation, experimental results for 2 thicknesses (2 mm and 4 mm) of plates are presented. Perforation tests are performed with an instrumented drop test. The striker has a large diameter and a conical shape nose. Two models for perforation are presented and calibrated to bring a better understanding of the experiments. The f...

  10. Aluminium phosphide poising: a case report

    International Nuclear Information System (INIS)

    This paper reports the case of a family in which three children were presented at Emergency Room (ER) with poisoning after the use of a pesticide at home. Initially, the cases were managed as routine cases of organophosphorus poisoning; however, the death of two children made the health team members realise that the poison's effects were delayed and devastating. Later, the compound was identified as Aluminium Phosphide (ALP), and the life of the last surviving child in the family was saved. (author)

  11. First wall design of aluminium alloy R-tokamak

    International Nuclear Information System (INIS)

    A design study of a low-activation D-T tokamak Reacting Plasma Project In Nagoya has been finished. The study emphasizes the vacuum vessel and the bumper limiter. Our choice of materials (aluminium vacuum vessel, copper conductors, aluminium TF coil case and lead shield) results in a radiation level of about 1 x 10-3 times that of a TFTR type design, and 1 x 10-4 times that of JET type design, at 2 weeks after one D-T shot. Thick graphite tiles will be fixed directly on the aluminium vacuum vessel using aluminium spring washers and bolts. With this simplified structure of the bumper limiter, the inner surface temperature of the thick aluminium vacuum vessel will be less than 1200C which is required to reduce the overaging effect of the aluminium alloy. (orig.)

  12. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. PMID:25687835

  13. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as permeability were observed for any of the three diatoms suggesting that mechanisms of aluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. PMID:26921729

  14. Aluminium matrix composites fabricated by infiltration method

    Directory of Open Access Journals (Sweden)

    L.A. Dobrzański

    2009-03-01

    Full Text Available Purpose: The aim of this work is to examine the structure and properties of metal matrix composites obtained by infiltration method of porous ceramic preforms by liquid aluminium alloy.Design/methodology/approach: Ceramic preforms were manufactured by the sintering method of ceramic powder. The preform material consists of powder Condea Al2O3 CL 2500, however, as the pore forming the carbon fibers Sigrafil C10 M250 UNS were used. Then ceramic preforms were infiltrated with liquid eutectic EN AC – AlSi12 aluminum alloy. Stereological and structure investigations of obtained composite materials were made on light microscope. The mechanical properties of obtained composite material were investigated in tensile strength test and hardness test.Findings: It was proved that developed technology of manufacturing of composite materials based on the porous ceramic Al2O3 preforms infiltrated by liquid aluminium alloy ensures expected structure and strength Hardness increased about twice compared to the matrix and this process can be used in practice.Practical implications: The presented metal matrix composites fabrication technology allows to obtain locally reinforced elements and near net shape products.Originality/value: Results show the possibility of obtaining the new aluminium matrix composite materials being the cheaper alternative for other materials based on the ceramic fibers.

  15. Plasmonic enhancement of photoluminescence from aluminium nitride

    Science.gov (United States)

    Flynn, Chris; Stewart, Matthew

    2016-03-01

    Aluminium nitride (AlN) films were grown on c-plane sapphire wafers by molecular beam epitaxy (MBE) under aluminium-rich conditions. The excess aluminium (Al) accumulated on the surface of the films as micro-scale droplets 1-10 μm in size, and as Al nanoparticles with diameters in the range 10-110 nm. Photoluminescence (PL) measurements were performed on the AlN samples using a 193 nm Excimer laser as the excitation source. Prior to PL measurements the wafers were cleaved in half. One half of each wafer was submitted to a 10 min treatment in H3PO4 heated to 70 °C to remove the excess Al from the film surface. The remaining half was left in the as-deposited condition. The mean intensities of the near-band-edge PL peaks of the as-deposited samples were 2.0-3.4 times higher compared to the samples subjected to the H3PO4 Al-removal treatment. This observation motivated calculations to determine the optimal Al surface nanosphere size for plasmonic enhancement of PL from AlN. The PL enhancement was found to peak for an Al nanosphere radius of 15 nm, which is within the range of the experimentally-observed Al nanoparticle sizes.

  16. Behaviour and design of aluminium alloy structural elements

    OpenAIRE

    Su, Meini; 蘇玫妮

    2014-01-01

    Aluminium alloys are nonlinear metallic materials with continuous stress-strain curves that are not well represented by the simplified elastic, perfectly plastic material model used in most existing design specifications. The aims of this study are to develop a more efficient design method for aluminium alloy structures by rationally exploiting strain hardening. The key components of this study include laboratory testing, numerical modelling and development of design guidance for aluminium al...

  17. Friction factor of CP aluminium and aluminium–zinc alloys

    Indian Academy of Sciences (India)

    N Vidhya Sagar; K S Anand; A C Mithun; K Srinivasan

    2006-12-01

    Friction factor has been determined for CP aluminium and aluminium–zinc alloys using ring compression test at different temperatures from 303 K to 773 K. It is found that CP aluminium exhibits sticking whereas Al–Zn alloys do not exhibit sticking at elevated temperatures. Hot working of Al–Zn alloy is easier than that of CP aluminium at 773 K. As zinc content increases up to 10 wt% the friction factor decreases up to 0.02.

  18. Softening Behaviour of Selected Commercially Pure Aluminium Model Alloys

    OpenAIRE

    Sande, Gunnar

    2012-01-01

    A characterization of the softening behaviour of four different commercially pure aluminium alloys has been carried out. The work is related to the MOREAL project (Modelling towards value-added recycling friendly aluminium alloys), where the main goal is to quantify the effect of the elements in recyclable aluminium alloys on microstructure and mechanical properties during thermo-mechanical processing. Typical elements are iron (Fe), silicon (Si) and manganese (Mn), and the alloys studied in ...

  19. Aluminium supplier selection for the automotive parts manufacturer

    OpenAIRE

    M. Cieśla

    2016-01-01

    This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method an...

  20. Multiply-negatively charged aluminium clusters and fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Noelle

    2008-07-15

    Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

  1. Tribological characteristics of coatings on aluminium and its alloys

    OpenAIRE

    Abdul-Mahdi, Fadhil S

    1987-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. Hard anodising on aluminium and its alloys has been widely practised for many years in order to improve the resistance of the otherwise poor wear characteristics of aluminium. In recent years there has been an increasing interest in other treatments and coatings, on both aluminium and other base metals. The aim of this investigation is to explain the tribological performance and wear mechanis...

  2. Wearing tests on aluminium coated with diamond by triboadhesion

    Institute of Scientific and Technical Information of China (English)

    J.M.RodríguezLelis; B.D.Angulo; J.O.Colín; J.PorcayoCalderón

    2001-01-01

    In this work the results obtained from subjecting aluminium coated with diamond by tri-boadhesion to a wearing process with a plane rider. Here it is shown the ratio of the normal toshearing forces, called friction factor, as an indication of the resistance of the surface. It was foundthat the film of the aluminium coated with diamond resisted three times compared with the oxida-tion film of commercial aluminium, which for the purpose of this work was considered withoutcoating.

  3. Un-optimistic Prospects for the Westward Movement of Aluminium

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>The westward movement of aluminium is essential for the industrial development.Up till now,the northwestern area has planned to construct more than 40 aluminium projects with a total production capacity of over 20 million tons.The future rate of progress of newly constructed projects are directly related to the supplies of the aluminium market,having critical guiding meaning for the trends of

  4. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    Directory of Open Access Journals (Sweden)

    B. Bobic

    2010-03-01

    Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

  5. Synthesis of aluminium nanoparticles by arc evaporation of an aluminium cathode surface

    Indian Academy of Sciences (India)

    M Gazanfari; M Karimzadeh; S Ghorbani; M R Sadeghi; G Azizi; H Karimi; N Fattahi; Z Karimzadeh

    2014-06-01

    Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on the nanoparticles was performed immediately. The effects of media on the yield and morphology of aluminium nanoparticles were investigated. Analysis result of the samples indicated that particle size was less than 30 nm, when 120 A/cm2 arc current was used. In addition, coating agent can affect arc velocity, arc stability, morphology and composition of the nanoparticles. Resultant nanoparticles were identified using X-ray powder diffraction (XRD), also their surface morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and finally the accuracy of coating was assessed with infrared (IR) spectroscopy.

  6. Thermal formation of corundum from aluminium hydroxides prepared from various aluminium salts

    Indian Academy of Sciences (India)

    J Temuujin; Ts JADAMBAA; K J D Mackenzie; P Angerer; F Porte; F Riley

    2000-08-01

    Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived from the sulfate. This contains a higher concentration of anionic impurities related to differences in the solubility of the original aluminium salts. The sulfate is retained in the gel to higher temperatures at which its eventual decomposition may lead to the formation of a reactive pore structure which facilitates the nucleation of -Al2O3.

  7. Aluminium composite casting dispersion reinforced with iron-aluminium and silicon carbide phases

    Directory of Open Access Journals (Sweden)

    B. Formanek

    2010-10-01

    Full Text Available Aluminium matrix composite with dispersion-reinforced, made by similar to stircasting process was characterised. The mixture of powders was produced by the process of mechanical agglomeration of powdered FexAly and SiC with aluminium. The chemical composition ofagglomerates was selected in a way such as to obtain 25 wt.% reinforcement of the AlSi9Cu4 silumin matrix. Applying thermal analysis ATD, the alloy solidification process was determined, reading out the typical solidification parameters. The methods of light and scanning microscopy were used to reveal the structure of composite casting. Changes in chemical composition and phase composition of particles of the FeAl intermetallic phase in aluminium matrix were confirmed. The structure of silumin casting with matrix containing microregions of ceramic and intermetallic phases, typical of hybrid reinforcements, was obtained.

  8. Doped aluminium based spinels synthesized by a soft chemistry method

    Energy Technology Data Exchange (ETDEWEB)

    Mindru, Ioana; Marinescu, Gabriela; Gingasu, Dana [Ilie Murgulescu Institute of Physical Chemistry, Splaiul Independentei 202, Bucharest 060021 (Romania); Patron, Luminita, E-mail: Luminita_Patron@yahoo.com [Ilie Murgulescu Institute of Physical Chemistry, Splaiul Independentei 202, Bucharest 060021 (Romania); Diamandescu, Lucian; Ghica, Corneliu; Mironov, Brandusa [National Institute for Materials Physics, Atomistilor Street, No. 105 bis, P.O. Box Mg-7, Bucharest-Magurele R 077125 (Romania)

    2010-06-15

    Structural and optical properties of (Co{sub 0.01}Zn{sub 0.99})Al{sub 2}O{sub 4} and Zn(Al{sub 1.99}Ln{sub 0.01})O{sub 4} (where Ln(III) = Eu(III), Tb(III)) spinels obtained by a variant of the complexation method-tartarate route were studied. The tartarate precursors have been characterized by IR, UV-vis and luminescence spectroscopy. The doped aluminium based spinels have been investigated by X-ray diffraction (XRD), transsmision electron microscopy (TEM), infrared spectroscopy (IR), ultraviolet visible spectroscopy (UV-vis) and luminescence spectroscopy. Pure spinel nanometer powders were obtained. Under excitation at 380 nm the nanoparticles exhibits strong luminescence corresponding to {sup 5}D{sub 0} {yields} {sup 7}F{sub 2} transition of Eu{sup 3+} ions and respectively, to {sup 5}D{sub 4} {yields} {sup 7}F{sub j} (j = 3, 4, 5, 6) transition of Tb{sup 3+} ions. No blue emission from the {sup 5}D{sub 3} state were observed.

  9. Cold-impregnated aluminium. A new source of nickel exposure.

    Science.gov (United States)

    Lidén, C

    1994-07-01

    A new technique for finishing anodized aluminium was introduced during the 1980s--cold impregnation with nickel. Nickel is available on the surface of cold-impregnated aluminium, as shown by the dimethylglyoxime test. Chemical analysis with EDXA showed that nickel was in the form of NiSO4. A case of work-related allergic contact dermatitis in an engraver with nickel allergy is reported. It transpired that the patient was exposed to nickel in connection with aluminium. It is concluded that cold-impregnated aluminium is a new source of nickel exposure, probably previously unknown to dermatologists. PMID:7924288

  10. Effects of aluminium surface morphology and chemical modification on wettability

    Science.gov (United States)

    Rahimi, M.; Fojan, P.; Gurevich, L.; Afshari, A.

    2014-03-01

    Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie-Baxter to Wenzel regime upon changing the surface roughness was also observed.

  11. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  12. A Reaction Coating on Aluminium Alloys by Laser Processing

    OpenAIRE

    Zhou, X.B.; De Hosson, J. Th. M.

    1993-01-01

    An aluminium oxide layer of 100 µm in thickness has been successfully coated on aluminium alloy 6061 and pure aluminium using a powder mixture of silicon oxide and aluminium by laser processing. A strong Al/Al2O3 interface was formed. The exothermic chemical reaction between SiO2 and Al may promote the metal/oxide wetting and the formation of Al2O3 layer. This new approach of ceramic coating on metals using a chemical reaction of other ceramics with metals may be applied to other systems.

  13. A study on the recycling of aluminium alloy 7075 scrap

    Energy Technology Data Exchange (ETDEWEB)

    Oezer, Goekhan [Yildiz Technical Univ., Yildiz (TR). Balkan Centre of Advanced Casting Technologies (BACAT); Marsoglu, Muezeyyen [Yildiz Technical Univ., Yildiz (Turkey). Dept. for Metal and Materials Science Engineering; Burgucu, Sarp

    2012-07-01

    Aluminium and its alloys have recently become an important metal whose area and amount of usage increase more and more, due to their mechanical properties, recycling ability, and penetrability. If it is considered that the bauxite, which is the raw material of aluminium is rare on earth, and also the area and amount of aluminium usage increases over time, the importance of aluminium recycling goes up. aluminium recycling has become crucial by means of both, the potential of the scrap's dependant increase on usage and the primary aluminium production, as it is providing energy and cost savings. 7xxx grades of scrap are collected with other scrap of aluminium alloys in one turn and recycled all together. As the regain of these alloys is not done by isolation of the various grades, the finally recycled ingots result in lower grades. High value aluminium scrap is regrettably not recovered, as it was anticipated. This study is dealing with 7075 aluminium alloys originated from discharged blow molding tools and the rest piece cuttings of blocks and plates. The material has been subjected to an induction furnace, and has been remelted into small ingots and hardened according to 7075 aluminium alloy parameters (hardening aluminium tooling). [German] Aluminium und seine Legierungen sind in den letzten Jahren aufgrund ihrer mechanischen Eigenschaften, ihrer Recyclingfaehigkeit und ihrer Durchlaessigkeit immer bedeutendere metallische Werkstoffe geworden. Unter Beruecksichtigung, dass Bauxit als Rohmaterial selten auf der Erde vorkommt und der Verbrauch mit der Zeit steigt, waechst die Bedeutung des Recyclings von Aluminium. Aluminiumrecycling, zumal es Energieund Kosteneinsparungen ermoeglicht, ist sowohl fuer die schrottabhaengigen Verwendungspotentiale und die PrimaerAluminiumproduktion gleichermassen bedeutend geworden. Die 7xxxx Schrottlegierungen werden in einem Arbeitsgang mit dem Schrott aus anderen Aluminiumlegierungen gesammelt und recycled. Da die

  14. There is (still too much aluminium in infant formulas

    Directory of Open Access Journals (Sweden)

    Burrell Shelle-Ann M

    2010-08-01

    Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

  15. Effects of aluminium surface morphology and chemical modification on wettability

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, M., E-mail: mar@sbi.aau.dk [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark); Fojan, P.; Gurevich, L. [Department of Physics and Nanotechnology, Aalborg University, Skjernvej 4, DK-9220 Aalborg East (Denmark); Afshari, A. [Department of Energy and Environment, Danish Building Research Institute, Aalborg University, A.C. Meyers Vænge 15, 2450 København SV (Denmark)

    2014-03-01

    Highlights: • Successful surface modification procedures on aluminium samples were performed involving formation of the layer of hydrophilic hyperbranched polyethyleneglycol (PEG) via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. • The groups of surfaces with hydrophobic behavior were found to follow the Wenzel model. • A transition from Cassie–Baxter's to Wenzel's regime was observed due to changing of the surface roughness upon mechanical polishing in aluminium samples. - Abstract: Aluminium alloys are some of the predominant metals in industrial applications such as production of heat exchangers, heat pumps. They have high heat conductivity coupled with a low specific weight. In cold working conditions, there is a risk of frost formation on the surface of aluminium in the presence of water vapour, which can lead to the deterioration of equipment performance. This work addresses the methods of surface modification of aluminium and their effect of the underlying surface morphology and wettability, which are the important parameters for frost formation. Three groups of real-life aluminium surfaces of different morphology: unpolished aluminium, polished aluminium, and aluminium foil, were subjected to surface modification procedures which involved the formation of a layer of hydrophilic hyperbranched polyethyleneglycol via in situ polymerization, molecular vapour deposition of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface

  16. Dihydroxy-Benzenes as Corrosion Inhibitors for Aluminium Sheet in Alkali Solution

    International Nuclear Information System (INIS)

    Additions of dihydroxy-benzenes (such as catechol, hydeoquinione and resorcinol)as corrosion inhibitors decrease the corrosion of aluminium sheet (which is given in the market) in 0.1M-1.0M sodium hydroxide solutions. The decrease is dependent upon the concentration of the sodium hydroxide and that of the inhibitor. Inhibitive efficiency is resorcinol < catechol< hydroquinone< resorcinol+hydroquinone at a concentration of 0.005% (w/w) dihydroxy-benzenes, and catechol< hydroquinone< resorcinol< resorcinol+hydroquinone at 0.5%, whereas the efficiency of all three inhibitors reaches approximately 100% at a concentration of 2% inhibitors in 0.1M NaOH. No correlation appears to exist between the inhibitor efficiency and the dissociation constant (Pk values) of the inhibitor. It can be said that 0.5M concentration of sodium hydroxide is the fittest for reducing the aluminium sheet by hydroquinone and formation of catechol-aluminium complex ions in the sodium hydroxide solutions

  17. Gas heat treatment plants for the aluminium industry; Gasbeheizte Waermebehandlungsanlagen fuer die Aluminium-Industrie

    Energy Technology Data Exchange (ETDEWEB)

    Olberts, P.; Hanus, A. [LOI Thermprocess GmbH, Essen (Germany)

    2004-09-01

    LOI Thermoprocess has developed new, flexible, innovative furnace designs for heat treatment of aluminium in general (car industry) and particularly for cylinder heads, engine units, chassis components, textured components, wheels, rolled sheet and extrusions. The furnaces are heated by means of radiant tubes (recuperators) and by the more usual open gas heating system (flue gas recirculation). (orig.)

  18. The aluminium body has been promoted in Canada; La carrosserie aluminium promue au Canada

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2004-02-01

    The aluminium vehicles technology is a technology which allows, with an equivalent structure, to decrease the weight of a car of 40%. Presented by the Alcan firm, this technology is one of the technologies of the year 2003. The Alcan firm has, besides, received the 2003 technology price awarded by the magazine Industry Week. (O.M.)

  19. Enhanced corrosion protection by microstructural control of aluminium brazing sheet

    NARCIS (Netherlands)

    Norouzi Afshar, F.

    2013-01-01

    Aluminium brazing sheet is a sandwich material made out of two aluminium alloys (AA4xxx/AA3xxx) and is widely used in automotive heat exchangers. One of the main performance criteria for heat exchanger units is the lifetime of the product. The lifetime of the heat exchanger units is determined by th

  20. Thermoelectric power of multilayer compositions of aluminium and carbon nanotubes

    International Nuclear Information System (INIS)

    Changing the thermoelectric power monolayer and multilayer aluminium foil and multilayer foils compositions of aluminium and carbon nanotubes is the deformation ε < 60% due to the scattering of conduction electrons at dislocations and ε=(70 ...96)% - due to their scattering on the boundaries between the layers (thermoelectric size effect)

  1. CAD implementation of design rules for aluminium extrusion dies

    NARCIS (Netherlands)

    Ouwerkerk, van Gijs

    2009-01-01

    Aluminium extrusion is an industrial forming process that is used to produce long profiles of a constant cross-section. This cross-section is shaped by the opening in a steel tool known as the die. The understanding of the mechanics of the aluminium extrusion process is still limited. The flow of al

  2. Spark counting technique with an aluminium oxide film

    International Nuclear Information System (INIS)

    Automatic spark counting of etch-pits on a polycarbonate film produced by nuclear fission fragments is now used for neutron monitoring in several countries. A method was developed using an aluminium oxide film instead of a polycarbonate as the neutron detector. Aluminium oxide films were prepared as follows: A cleaned aluminium plate as an anode and a nickel plate as a cathode were immersed in dilute sulfuric acid solution and electric current flowed between the electrodes at 12degC for 10-30 minutes. Electric current density was about 10 mA/cm2. The aluminium plate was then kept in boiling water for 10-30 minutes for sealing. The thickness of the aluminium oxide layer formed was about 1μm. The aluminium plate attached to a plate of suitable fissionable material, such as uranium or thorium, was irradiated with neutrons and set in a usual spark counter for fission track counting. One electrode was the aluminium plate and the other was an aluminized polyester sheet. Sparked pulses were counted with a usual scaler. The advantage of using spark counting with an aluminium oxide film for neutron monitoring is rapid measurement of neutron exposure, since chemical etching which is indispensable for spark counting with a polycarbonate detector film, is not needed. (H.K.)

  3. The peculiarities of scandium and yttrium dissolution in aluminium melt

    International Nuclear Information System (INIS)

    The investigation results of dissolution of scandium and yttrium in liquid aluminium at 973-1173 K are presented in this work. It was shown that coefficient value of yttrium diffusion in aluminium melt equals to 3,566-17,9070 m2/sec, and scandium 9,692-4,072 m2/sec.

  4. Haemodialysis related osteomalacia: a staining method to demonstrate aluminium

    OpenAIRE

    Buchanan, Malcolm RC; Ihle, Benno U; Dunn, Cheryl M

    1981-01-01

    A slight modification in tissue processing and staining technique enables a previously described method for staining aluminium to be used to demonstrate aluminium in osteomalacia associated with haemodialysis. The stain appears to be accurate in diagnosing this condition and may assist in establishing the diagnosis before severe osteomalacia develops.

  5. Aluminium Alloy Cast Shell Development for Torpedoes

    Directory of Open Access Journals (Sweden)

    Vijaya Singh

    2005-01-01

    Full Text Available The sand-cast aluminium alloy cylindrical shells were developed for the advanced experimental torpedo applications. The components had intricate geometry, thin-walled sections, and stringent property requirements. The casting defects, such as shrinkage, porosity, incomplete filling of thin sections, cold shuts, inclusions and dimensional eccentricity, etc were found inthe initial castings trials. improvements in casting quality were achieved through modified methodology, selective chilling, risering, and by introducing ceramic-foam filters in the gatingsystem. The heat-treated and machined components met radiographic class I grade C/E standards, mechanical properties to BS1490 specifications, and leakage and hydraulic pressure testrequirements relevant for such applications.

  6. Dissolved aluminium in the Southern Ocean

    OpenAIRE

    Middag, R.; Slooten van, C.; Baar, H.J.W. de; Laan, P.

    2011-01-01

    Dissolved aluminium (Al) occurs in a wide range of concentrations in the world oceans. The concentrations of Al in the Southern Ocean are among the lowest ever observed. An all-titanium CTD sampling system makes it possible to study complete deep ocean sections of Al and other trace elements with the same high vertical resolution of 24 depths as normal for traditional CTD/Rosette sampling. Overall, 470 new data points of Al are reported for 22 full depth stations and 24 surface sampling posit...

  7. Roll casting of 5182 aluminium alloy

    OpenAIRE

    Haga, T; M. Mtsuo; D. Kunigo; Hatanaka, Y; R. Nakamuta; H. Watari; S. Kumai

    2009-01-01

    Purpose: of this paper is investigation of the ability of the high speed roll casting of 5182 aluminium alloy. Appropriate twin roll caster to cast the 5182 strip was researched.Design/methodology/approach: Method used in the present study was an unequal diameter twin roll caster and a vertical type high speed twin roll caster equipped with mild steel rolls without parting material.Findings: are that the vertical type high speed twin roll caster was effective to cast 5182 strip at high speed....

  8. On the Crystallization of Terbium Aluminium Garnet

    OpenAIRE

    Ganschow, S.; Klimm, D.; Reiche, P.; Uecker, R.

    2008-01-01

    Attempts to grow terbium aluminium garnet (Tb3Al5O12, TAG) by the Czochralski method lead to crystals of millimeter scale. Larger crystals could not be obtained. DTA measurements within the binary system showed that TAG melts incongruently at 1840 deg. C. The perovskite (TbAlO3, TAP) with a congruent melting point of 1930 deg. C is the most stable phase in this system. The region for primary crystallization of TAP covers the chemical composition of TAG and suppresses the primary crystallizati...

  9. Friction stir welding of single crystal aluminium

    DEFF Research Database (Denmark)

    Fonda, Richard Warren; Wert, John A.; Reynolds, A.P.;

    2007-01-01

    Friction stir welds were prepared in different orientations in an aluminium single crystal. The welds were quenched to preserve the microstructure surrounding the tool and then electron backscattered diffraction was used to reveal the generation of grain boundaries and the evolution of...... crystallographic texture around the tool in each weld. The extent of both dynamic recrystallisation and conventional recrystallisation varied considerably as a function of weld orientation. As the base plate begins to interact with the deformation field surrounding the tool, regions of the single crystal rotate to...

  10. Intercomparison 9711. pH, conductivity, alkalinity, nitrate + nitrite, chloride, sulfate, calcium, magnesium, sodium, potassium, total aluminium, reactive and non-labile aluminium, dissolved organic carbon, and chemical oxygen demand

    Energy Technology Data Exchange (ETDEWEB)

    Hovind, Haavard

    1997-09-22

    The work described in this report was a part of an international cooperative programme for assessment and monitoring of acidification of rivers and lakes. Two sample sets were prepared for intercomparison, one for determination of the major ions, the other for determination of aluminium fractions and unspecified organic matter. The samples were sent to 50 laboratories and 47 laboratories from 22 countries submitted results. Good agreement was found for chloride, sulfate, calcium, magnesium, sodium and the unspecific organic compounds, dissolved organic carbon and chemical oxygen demand, more than 80% being evaluated as acceptable for these analytic variables. The results for nitrate + nitrite and aluminium species did not agree well, probably because different methods were used to determine the aluminium species. On the whole, 78% of the results were within the general target accuracy of plus or minus 20%. Laboratories with results outside this accuracy should improve their methods if they want to analyse low-concentration samples. To improve the compatibility of the analytical results for aluminium fractions, it seems necessary to normalize the analytical methods and determination techniques used for these determinations. A total error of plus minus 0.2 pH units seems to be a reasonable assessment of the accuracy for pH measurements when weakly acid or neutral water samples not in CO{sub 2} equilibrium are analyzed. 7 refs., 1 fig., 34 tabs.

  11. Durability of Lacquered Aluminium Profile Considering Tropical Weather Conditions

    Directory of Open Access Journals (Sweden)

    Rigoberto Marrero Águila

    2013-11-01

    Full Text Available Searching for solutions against the degradation of materials by corrosion effect, is a common practice to use alloys such as aluminium instead of steel due to the advantages obtained. The lacquered aluminium profiles can substitute other materials like wood, in the carpentry production, becoming an economic saving. There is an increasingly use of aluminium replacing other traditional materials in the constructions in process, but its quality has been reduced in a considerable amount of installations. In this research, aluminium profiles from five different sources were submitted to a trial in natural exposition conditions at the Tropical weather condition Testing Lab, in order to evaluate their behaviour and establish, for the first time in our country, standing rules for lacquered aluminium profiles to be strictly fulfilled by manufacturers and importers. The results will allow modifying thickness standards of this type of coating, to guaranty its durability and to eliminate the failures provoked by our high severe weather conditions.

  12. FIB-SEM investigation of trapped intermetallic particles in anodic oxide films on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.;

    2011-01-01

    using focused ion beam-scanning electron microscopy (FIB-SEM), SEM, and EDX. Findings - The intermetallic particles in the substrate material consisted of Fe or both Fe and Si with two different structures: irregular and round shaped. FIB-SEM cross-sectioned images revealed that the irregular....../Si ratio of the intermetallic particles decreased after anodizing. Originality/value - This paper shows that dual beam FIB-SEM seems to be an easy, less time consuming and useful method to characterize the cross-sectioned intermetallic particles incorporated in anodic film on aluminium....

  13. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    International Nuclear Information System (INIS)

    Highlights: ► Aluminium packaging partitioning in MSW incineration residues is evaluated. ► The amount of aluminium packaging recoverable from the bottom ashes is evaluated. ► Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. ► 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  14. New sheet aluminium qualities for low-cost lightweight constructions; Neue Aluminium-Blechqualitaeten fuer den kosteneffizienten Leichtbau

    Energy Technology Data Exchange (ETDEWEB)

    Bloeck, M.; Furrer, P. [Novelis Technology AG, Neuhausen (Switzerland)

    2005-11-01

    Aluminium alloys used for car bodies have a wide range of material characteristics. New developments focus on selective development of material and surface characteristics for obtaining sheet aluminium qualities optimized for specific applications. These and further measures taken by Novelis are to reduce material consumption, simplify process steps in motor car manufacturing and reducing the overall system cost. (orig.)

  15. Design of the lines of aluminium drawing. Part 2; Conception des filieres de filage d'aluminium. Partie 2

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    This work is the second part of the file 'design of the lines of aluminium drawing'. It gives elements for structuring the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  16. Anti corrosion layer for stainless steel in molten carbonate fuel cell - comprises phase vapour deposition of titanium nitride, aluminium nitride or chromium nitride layer then oxidising layer in molten carbonate electrolyte

    DEFF Research Database (Denmark)

    2000-01-01

    Forming an anticorrosion protective layer on a stainless steel surface used in a molten carbonate fuel cell (MCFC) - comprises the phase vapour deposition (PVD) of a layer comprising at least one of titanium nitride, aluminium nitride or chromium nitride and then forming a protective layer in situ...... by replacement of the nitride ions with oxide ions in the molten carbonate electrolyte....

  17. Aluminium and its alloys: weldability, welding metallurgy; L'aluminium et ses alliages: soudabilite, metallurgie du soudage

    Energy Technology Data Exchange (ETDEWEB)

    Boucher, Ch.

    2000-07-01

    The aim of this book is to give technological and use elements of the welding processes as well as the knowledge in weldability and metallurgy required for a better control of the welding of aluminium alloys. In the first part are detailed the generalities on aluminium alloys, their properties and uses sectors. The bases of the physical metallurgy of the aluminium alloys are dealt with too. The second part concerns the welding and the related techniques as well as the properties of the assemblies. Several supplements give useful data for the construction with aluminium alloys. This book is particularly devoted to engineers and technicians using or having to use for the first time the welding of aluminium alloys. (O.M.)

  18. Hearing conservation in the primary aluminium industry

    Science.gov (United States)

    Frisch, N.; Dixon-Ernst, C.; Chesson, B. J.; Cullen, M. R.

    2016-01-01

    Background Noise-induced hearing loss has been an intractable problem for heavy industry. Aims To report our experience in reducing the incidence of age-corrected confirmed 10 dB hearing shifts (averaged over 2, 3 and 4kHz) in employees in the primary aluminium industry in Australia over the period 2006–13. Methods We analysed annual audiometric data to determine the number of permanent hearing shifts that occurred in employees in two bauxite mines, three alumina refineries and two aluminium smelters. Annual hearing shift rates were calculated based on the number of employees tested per year. Hearing conservation initiatives undertaken during the study period are described. An assessment of similar exposure group noise exposures was also undertaken to determine the magnitude of noise exposure reduction during the study period. Results Across all operations, hearing shift rates declined from 5.5% per year in 2006 to 1.3% per year in 2013 (P < 0.001). The decline in shift rates was greater in mines and refineries, where baseline shift rates were higher, than in smelter workers. Modest reductions in noise exposure occurred during the study period. Conclusions We observed a substantial decline in hearing shift rates during the study period. We describe the hearing conservation initiatives that were collectively associated with this decline. We suspect these initiatives could be deployed relatively easily and at modest cost in other industries with noise-exposed employees. PMID:26470945

  19. Reactions on carbon anodes in aluminium electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Eidet, Trygve

    1997-12-31

    The consumption of carbon anodes and energy in aluminium electrolysis is higher than what is required theoretically. This thesis studies the most important of the reactions that consume anode materials. These reactions are the electrochemical anode reaction and the airburn and carboxy reactions. The first part of the thesis deals with the kinetics and mechanism of the electrochemical anode reaction using electrochemical impedance spectroscopy. The second part deals with air and carboxy reactivity of carbon anodes and studies the effects of inorganic impurities on the reactivity of carbon anodes in the aluminium industry. Special attention is given to sulphur since its effect on the carbon gasification is not well understood. Sulphur is always present in anodes, and it is expected that the sulphur content of available anode cokes will increase in the future. It has also been suggested that sulphur poisons catalyzing impurities in the anodes. Other impurities that were investigated are iron, nickel and vanadium, which are common impurities in anodes which have been reported to catalyze carbon gasification. 88 refs., 92 figs., 24 tabs.

  20. Study on aluminium-based single films.

    Science.gov (United States)

    Vinod Kumar, G S; García-Moreno, F; Babcsán, N; Brothers, A H; Murty, B S; Banhart, J

    2007-12-28

    In the present paper the authors studied isolated metallic films made from the same material used for making metallic foams, and then characterised their properties. Metal films were made from a liquid aluminium alloy reinforced with ceramic particles of known concentration. Melts without such particles were also investigated. It is shown that stable films could not be made from Al-Si alloy having no particles, and just extremely thin and fragile films could be made from commercially-pure Al. In contrast, aluminium alloys containing particles such as SiC and TiB(2) allowed pulling thin, stable films, which did not rupture. Significant thinning of films was observed when the particle concentration in the melt decreased. By in situ X-ray monitoring of liquid films during pulling, film thickness and drainage effects within the liquid film could be studied. The morphology and microstructure of films was characterised after solidification. Our work shows that the question of how foams are stabilised can be studied using a simplified system such as a film, instead of having to deal with the multitude of different structural elements present in a foam. PMID:18060172

  1. Aluminium matrix composites: Challenges and opportunities

    Indian Academy of Sciences (India)

    M K Surappa

    2003-02-01

    Aluminium matrix composites (AMCs) refer to the class of light weight high performance aluminium centric material systems. The reinforcement in AMCs could be in the form of continuous/discontinuous fibres, whisker or particulates, in volume fractions ranging from a few percent to 70%. Properties of AMCs can be tailored to the demands of different industrial applications by suitable combinations of matrix, reinforcement and processing route. Presently several grades of AMCs are manufactured by different routes. Three decades of intensive research have provided a wealth of new scientific knowledge on the intrinsic and extrinsic effects of ceramic reinforcement vis-a-vis physical, mechanical, thermo-mechanical and tribological properties of AMCs. In the last few years, AMCs have been utilised in high-tech structural and functional applications including aerospace, defence, automotive, and thermal management areas, as well as in sports and recreation. It is interesting to note that research on particle-reinforced cast AMCs took root in India during the 70’s, attained industrial maturity in the developed world and is currently in the process of joining the mainstream of materials. This paper presents an overview of AMC material systems on aspects relating to processing, microstructure, properties and applications.

  2. Aluminium alloys containing iron and nickel

    International Nuclear Information System (INIS)

    The first part of this report addresses mechanism, kinetics and structure factors of aluminium alloys containing iron and nickel in water and high temperature steam. The studied alloys contain from 0.3 to 0.7 per cent of iron, and 0.2 to 1.0 per cent of nickel. Corrosion resistance and corrosion structure have been studied. The experimental installation, process and samples are presented. Corrosion structures in water at 350 C are identified and discussed (structure of corrosion products, structure of metal-oxide interface), and then in steam at different temperatures (350-395 C). Corrosion kinetics is experimentally studied (weight variation in time) in water at 350 C and in steam at different temperatures. Reactions occurring at over-heated steam (more than 400 C) are studied, and the case of welded alloys is also addressed. The second part addresses the metallurgical mechanism and processes influencing aluminium alloy resistance to corrosion by high temperature water as it appeared that separated phases protect the solid solution through a neighbourhood action. In order to avoid deep local corrosions, it seems necessary to multiply protective phases in an as uniform as possible way. Some processes enabling this result are described. They belong to conventional metallurgy or to powder metallurgy (with sintering and extrusion)

  3. Laser welding of copper and aluminium battery interconnections

    Science.gov (United States)

    De Bono, Paola; Blackburn, Jon

    2015-07-01

    The adoption of lithium-ion and/or super-capacitor battery technologies is a current hot topic in the automotive industry. For both battery types, the terminals and busbars are manufactured from copper (Cu) and/or aluminium-based (Al-based) alloys, as a result of their high electrical and thermal conductivities. Laser welding is considered an attractive process to industry due to its easy automotability, high processing speed and highly repeatable cost-effective processing. However, laser welding of Cu-Cu and Al-Al joints presents several difficulties due to the high surface reflectivity at infrared (IR) wavelengths. This behaviour becomes even more critical when processing thin sheets and foils.This paper summarises recent work performed to develop laser welding techniques suitable for monometallic joining of Cu-Cu and Al-Al electrical interconnections. Laser welding of multiple overlapped foils (with thickness in the range of 17μm-100μm) were investigated.

  4. Investigation of blistering kinetics in hydrogen implanted aluminium nitride

    International Nuclear Information System (INIS)

    Epitaxial layers of aluminium nitride (AlN) grown on sapphire by hydride vapour phase epitaxy (HVPE) were implanted with 100 keV hydrogen, H+2, ions with doses in the range of 5 × 1016–2.5 × 1017 cm−2 and subsequently annealed in ambient air at temperatures between 450 and 750 °C in order to determine the kinetics of surface blister formation in AlN. The Arrhenius plot of the blistering time versus temperature shows two different activation energies for the formation of surface blisters: 0.44 eV in the higher temperature regime of 550–750 °C and 1.16 eV in the lower temperature regime of 450–550 °C. The implantation-induced damage was analyzed by cross-sectional transmission electron microscopy, which revealed a band of defects extending from 330 to 550 nm from the surface of AlN. The XTEM image of the implanted and annealed AlN displayed clearly the formation of microcracks that ultimately lead to the formation of surface blisters

  5. Preparation of Aluminium Oxynitride by Carbothermal Reduction of Aluminium Oxide in a Flowing N2 Atmosphere

    Institute of Scientific and Technical Information of China (English)

    LIYa-wei; YUANRun-zhang; 等

    1996-01-01

    Carbothermal reduction of alumina into aluminium oxynitride(AlON) spinel in a flowing nitrogen atmosphere was studied.The effects of Al2O3/C ratio temperature,soaking time,heating rate molding pressure of samples,and nitrogen flow rate on reactions were investigated.Then the stability of AlON was elucidated and AlON wa confirmed as an intermediate compound in reduction of alumina.

  6. INTEROGATION OF THE MANUFACTURING ROUTE OF ALUMINIUM AA 1050 USED IN LITHOGRAPHIC APPLICATION

    OpenAIRE

    Witkowska, Malgorzata Danuta

    2013-01-01

    The aluminium AA1050 alloy, known as commercially pure aluminium, contains 99.5% Al, together with Fe and Si as major alloying elements. During fabrication of aluminium substrates for lithographic printing plates in Bridgnorth Aluminium Ltd, the AA 1050 aluminium alloy proceeds through various stages of thermomechanical processing, with the conditions at each processing stage influencing the microstructure of the final coil. Because of its specific gravity, tensile strength, surface performa...

  7. Effect of filtration on reoxidation proceses in aluminium alloys

    Directory of Open Access Journals (Sweden)

    D. Bolibruchova

    2010-01-01

    Full Text Available This article is focused on reoxidation processes during filtration of aluminium alloys. Many of our experimental works pointed out, that using filtration media placed in gating system causes reoxidation of poured aluminium alloy. Main aim of our latest work was to validate our arguments, that filter in gating system can be considered as obstacle for continuous pouring, with help of computer simulations. This article is only a small part of our researches focused on reoxidation processes during filtration of aluminium alloys.

  8. Aluminium: Aluminij: kovina izbire: the metal of choice:

    OpenAIRE

    Gándara, María Josefa Freiría

    2013-01-01

    This article summarizes the importance of aluminium as the metal of choice formany applications. Aluminium is a lightweight, durable metal. It is silvery in appearance when freshly cut, is a good conductor of heat and electricity, and is easily shaped by moulding and extruding. Aluminium has two main advantages when compared with other metals. Firstly, it has a low density, about one-third that of iron and copper. Secondly, although it reacts rapidly with the oxygen in air, it forms a thin, t...

  9. Cold forming of aluminium - State of the art

    DEFF Research Database (Denmark)

    Bay, Niels

    1997-01-01

    The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable to that of...... unalloyed steel. After description of the different types of alloys and their individual properties and applications, the special requirements for tool design by cold forging in aluminium is discussed. Finally, a large number of industrial examples on cold forged aluminium components are presented. (C) 1997...

  10. Radiation-induced creep of copper, aluminium and their alloys

    International Nuclear Information System (INIS)

    The results of creep studies on copper, aluminium and their alloys with and without neutron irradiation are presented. The experiments are carried out at the WWR-K reactor at the neutron fluence of 1.4.1016 n/m2.s (2.5.1016 n/m2.s, E>0.1 MeV). Polycrystalline copper (99.99 and 99.95%), aluminium (99.99%) and the alloys of copper with 4 at% of titanium, of aluminium with 4.2% of copper are studied within the temperature interval 0.31-0.51 Tm. (orig.)

  11. 59Fe distribution in continuously cast aluminium strip

    International Nuclear Information System (INIS)

    The problems are discussed of the homogeneity of continuously cast aluminium strips by horizontal casting. Theoretically discussed are phenomena present during primary solidification, namely the nonhomogeneous distribution of admixtures and impurities in primary solidified dendritic cells. A survey is given of the distribution of coefficients of basic admixtures and impurities in aluminium. Experimental investigation was carried out within the verification of theoretical research results, of the distribution of iron in continuously cast aluminium strips using radioactive iron 59Fe in form of radioactive foundry alloy containing 1.8% 59Fe. (author). 13 figs., 1 tab

  12. Optimization of Magnesium Metal into Commercially Pure Aluminium

    Directory of Open Access Journals (Sweden)

    Vandana J Rao

    2014-02-01

    Full Text Available The present investigation, involve development of Al-Mg systems by addition of magnesium into commercially pure aluminium. The amounts of magnesium added into commercially pure aluminium are of 1 and 2 wt%. The recoveries of magnesium are around 85-90%.Remaining Mg react with oxygen and float on the liquid aluminium. Presence of magnesium creates two phenomena. One is solid solution hardening and other is intermetallics formation. Both the phenomena checked by microstructural changes and by measuring the electrical conductivity values. By increasing the Mg, content mechanical properties (hardness and tensile strength increases and electrical conductivity decreases.

  13. Corrosion issues of powder coated AA6060 aluminium profiles

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl;

    2015-01-01

    In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

  14. Study of fatigue behaviour of 7475 aluminium alloy

    Indian Academy of Sciences (India)

    B B Verma; J D Atkinson; M Kumar

    2001-04-01

    Fatigue properties of a thermomechanically treated 7475 aluminium alloy have been studied in the present investigation. The alloy exhibited superior fatigue life compared to conventional structural aluminium alloys and comparable stage II crack growth rate. It was also noticed that the fatigue crack initiated from a surface grain and the crack extension was dominated by ductile striations. Analysis also revealed that this alloy possessed fracture toughness and tensile properties superior to that noticed with other structural aluminium alloys. Therefore the use of this alloy can safely reduce the overall weight of the aircraft.

  15. Mechanical alloying of aluminium-lithium-magnesium alloy powders

    International Nuclear Information System (INIS)

    The production of high-purity aluminium-lithium-magnesium alloy powders, by mechanical alloying through grinding in a vibratory mill under high vacuum at room temperature, is described in details. The source materials for the grinding mixture were: aluminium-lithium alloy powder obtained by thermal vacuum-dehydrogenization of AlLiH4 hydride; magnesium metal powder; and chemically deoxidized aluminium metal powder. The implications which arose from the high reactivity of the component elements are discussed, and the measures taken to overcome them are described. The procedures used for the chemical analysis and powder characterization are given. (orig.)

  16. Aluminium content of some foods and food products in the USA, with aluminium food additives.

    Science.gov (United States)

    Saiyed, Salim M; Yokel, Robert A

    2005-03-01

    The primary objective was to determine the aluminium (Al) content of selected foods and food products in the USA which contain Al as an approved food additive. Intake of Al from the labeled serving size of each food product was calculated. The samples were acid or base digested and analysed for Al using electrothermal atomic absorption spectrometry. Quality control (QC) samples, with matrices matching the samples, were generated and used to verify the Al determinations. Food product Al content ranged from Cheese in a serving of frozen pizzas had up to 14 mg of Al, from basic sodium aluminium phosphate; whereas the same amount of cheese in a ready-to-eat restaurant pizza provided 0.03-0.09 mg. Many single serving packets of non-dairy creamer had approximately 50-600 mg Al kg(-1) as sodium aluminosilicate, providing up to 1.5 mg Al per serving. Many single serving packets of salt also had sodium aluminosilicate as an additive, but the Al content was less than in single-serving non-dairy creamer packets. Acidic sodium aluminium phosphate was present in many food products, pancakes and waffles. Baking powder, some pancake/waffle mixes and frozen products, and ready-to-eat pancakes provided the most Al of the foods tested; up to 180 mg/serving. Many products provide a significant amount of Al compared to the typical intake of 3-12 mg/day reported from dietary Al studies conducted in many countries. PMID:16019791

  17. Orbital friction stir welding of aluminium pipes

    International Nuclear Information System (INIS)

    Friction stir welding (FSW) was originally developed for flat plates. This contribution shows how it can be applied to the welding of aluminium pipes. Pipes made of AlMG 3 (EN5754), AlMg 4.5Mn (EN5083) and AlMgSi 0.5 (EN6106) with dimensions of Da 600 and 520 x 10-8 mm were welded. The FSW orbital system comprises an annular cage with integrated FSW head, a hydraulic system, and a control unit. The welds were tested successfully according to EN 288. The mechanical and technical properties of the welds were somewhat better than with the TIG orbital process, and welding times were about 40 percent shorter

  18. Silane based coating of aluminium mold

    DEFF Research Database (Denmark)

    2013-01-01

    A method of preparing an aluminum mold for injection molding is provided, the method comprises the steps of providing an aluminum mold having a least one surface, subjecting the at least one surface to a gas or liquid phase silane to thereby form an anti-stiction coating, the anti-stiction coating...... comprising a chemically bonded monolayer of silane compounds on the at least one surface wherein the silane is a halogenated silane. The at least one surface coated with the anti-stiction coating may be configured to withstand an injection molding process at a pressure above 100 MPa. Furthermore, a mold...... having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding of...

  19. Mechanical behaviour of aluminium-lithium alloys

    Indian Academy of Sciences (India)

    N Eswara Prasad; A A Gokhale; P Rama Rao

    2003-02-01

    Aluminium-lithium alloys hold promise of providing a breakthrough response to the crying need for lightweight alloys for use as structurals in aerospace applications. Considerable worldwide research has gone into developing a range of these alloys over the last three decades. As a result, substantial understanding has been developed of the microstructure-based micromechanisms of strengthening, of fatigue and fracture as well as of anisotropy in mechanical properties. However, these alloys have not yet greatly displaced the conventionally used denser Al alloys on account of their poorer ductility, fracture toughness and low cycle fatigue resistance. This review aims to summarise the work pertaining to study of structure and mechanical properties with a view to indicate the directions that have been and can be pursued to overcome property limitations.

  20. Experimental analysis of cut welding in aluminium

    DEFF Research Database (Denmark)

    Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

    1993-01-01

    Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...... tensile testing and metallographic investigations of the welds. The results show that this variant of cut welding is a very reproducible process giving a weld strength equal to 30-40% the strength of the parent material. The experiments have shown that the reason for this relatively low strength is an...... uneven pressure distribution along the weld due to a wave formed during sliding. Attempts to alter the material flow during sliding are presented....

  1. Adsorption of aluminium by stream particulates.

    Science.gov (United States)

    Tipping, E; Ohnstad, M; Woof, C

    1989-01-01

    An experimental study was made of the adsorption of aluminium by fine particulates from Whitray Beck, a hill stream in NW England. Adsorption increased with Al(3) activity, pH and concentration of particles, and could be quantitatively described by the empirical equation: [Formula: see text] [particles] where square brackets indicate concentrations, curly brackets, activities, and alpha, beta and gamma are constants with values of 5.14x10(-10) (mol litre(-1))(2.015) (g particles litre(-1))(-1), 0.457, and 1.472, respectively. For the experimental data, the equation gave a correlation ratio of 0.99. The equation accounts reasonably well for the adsorption of Al by particulates from seven other streams. In applying the equation, it must be borne in mind that the desorption kinetics of Al depend on pH, and rapid reversibility (or=10%) of total monomeric Al. PMID:15092454

  2. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. PMID:26365318

  3. Corrosion of spent nuclear fuel aluminium cladding in ordinary water

    International Nuclear Information System (INIS)

    Corrosion of aluminium alloy cladding of spent nuclear fuel elements in ordinary water is examined in the spent fuel storage pool of the RA research reactor at the Vinca Institute of Nuclear Sciences, Belgrade, Serbia and Montenegro. Experimental examinations are carried out within framework of the International Atomic Energy Agency (IAEA) Coordinated Research Project (CRP) 'Corrosion of Research Reactor Aluminium-Clad Spent Fuel in Water', Phase II. Racks with coupons made of different aluminium alloys were exposed to water influence for period of six months to six years. The project comprises also activities on monitoring of the water chemistry and radioactivity in the storage pool. Visual and microscopic examinations of surfaces of aluminium coupons of the test racks have been done recently and results were presented in this paper confirming strong influence of water quality and exposition time to corrosion process. (author)

  4. Advances in development and application of aluminium batteries

    DEFF Research Database (Denmark)

    Qingfeng, Li; Zhuxian, Qiu

    2001-01-01

    Aluminium has long attracted attention as a potential battery anode because of its high theoretical voltage and specific energy. The protective oxide layer at aluminium surface is however detrimental to its performance to achieve its reversible potential, and also causing the delayed activation of...... anode. The oxide layer can be removed by e.g. amalgamation but this will result in accelerated corrosion and poor shelf life. These difficulties have been successfully overcome by developing alloying elements and electrolyte additives in the recent years. The literature review also includes various...... aluminium batteres, especially aluminium-air batteries, and a wide range of their applications from emergency power supplies, reserve batteries field portable batteries, to batteries for electric vehicles and underwater propulsion....

  5. Deposition of aluminium nanoparticles using dense plasma focus device

    International Nuclear Information System (INIS)

    Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

  6. Aluminium foam sandwich panels: manufacture, metallurgy and applications

    Energy Technology Data Exchange (ETDEWEB)

    Banhart, J. [Hahn-Meitner-Institut, TU Berlin (Germany); Seeliger, H.W. [Alm GmbH, Saarbruecken (Germany)

    2008-09-15

    Sandwich panels consisting of a highly porous aluminium foam core and aluminium alloy face sheets are manufactured by roll-bonding aluminium alloy sheets to a densified mixture of metal powders - usually Al-Si or Al-Si-Cu alloys with 6-8% Si and 3-10% Cu - and titanium hydride, and foaming the resulting three-layer structure by a thermal treatment. We review the various processing steps of aluminium foam sandwich (AFS) and the metallurgical processes during foaming, compare the process to alternative ways to manufacture AFS, e.g. by adhesive bonding, and give an overview of the available literature. Two ways to treat AFS after foaming are presented, namely forging and age-hardening. Some current and potential applications are described and the market potential of AFS is assessed. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

  7. Local electrochemical behaviour of 7xxx aluminium alloys

    OpenAIRE

    F. Andreatta

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a negative effect on safety and costs. This PhD thesis investigates the relation between electrochemical behaviour and microstructure of a number of 7xxx aluminium alloys: AA7075, AA7349 and an experime...

  8. Crushing modes of aluminium tubes under axial compression

    OpenAIRE

    Pled, Florent; Yan, Wenyi; Wen, Cui'e

    2014-01-01

    6 pages International audience A numerical study of the crushing of circular aluminium tubes with and without aluminium foam fillers has been carried out to investigate their buckling behaviours under axial compression. A crushing mode classification chart has been established for empty tubes. The influence of boundary conditions on crushing mode has also been investigated. The effect of foam filler on the crushing mode of tubes filled with foam was then examined. The predicted results ...

  9. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Ivan Michalec

    2013-01-01

    Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  10. Modeling of aluminium deposition from chloroaluminate ionic liquids

    OpenAIRE

    Schaltin, Stijn; Ganapathi, Murugan; Binnemans, Koen; Fransaer, Jan

    2011-01-01

    A finite-element model of the electrodeposition of aluminium from chloroaluminate ionic liquids is introduced. The purpose of this model is to give an explanation for the reasonable current densities that can be achieved in chloroaluminate ionic liquids despite the fact that the electrochemically active Al2Cl7- complexes are transformed into inactive AlCl4- complexes during the electrodeposition of aluminium. The obtainable current density in the electrodeposition from chloroaluminate ionic l...

  11. TORSIONAL DEFORMATION AND FATIGUE BEHAVIOUR OF 6061 ALUMINIUM ALLOY

    OpenAIRE

    Marini Marno; Ahmad Badri Ismail

    2012-01-01

    Torsional deformation and fatigue behaviour of both solid and thin-walled tubular specimens were made from as-received and heat treated 6061 aluminium alloy were studied. 6061 aluminium alloy have been widely used as a candidate material in automobile, aerospace, aircraft and structural application because of their superior mechanical properties such as high strength to weight ratio, good ductility and others. The differences in cyclic deformation and fatigue behaviours between round and soli...

  12. Ball Pad Mold Electromagnetic Forming Process for Aluminium Alloy Sheet

    OpenAIRE

    Wang, Wen-ping; Wu, Xiang-Dong; Wan, Min; Chen, Xiao-wei; Xiong, Wei-Ren

    2014-01-01

    In order to meet requirements of lightweight technology in the field of aerospace, the new forming technology for aluminium alloy skin parts and integral panel are brought to more attention. Based on the principle of electromagnetic forming (EMF) and energy distribution, a new electromagnetic forming process using ball as pad mold for aluminium alloy sheet forming was suggested and test apparatus was designed. The new method was verified by the finite element simulation and exp...

  13. Blast Loaded Aluminium Plates : Experiments and numerical simulations

    OpenAIRE

    Melby, Emil Arne; Eide, Hilde Olaug Stakvik

    2013-01-01

    Light and flexible protective constructions in aluminium could be subjected to a blast load. In this thesis the effect of blast loading on aluminium plates of the type 1050A ? H14 was studied through experiments and numerical simulations. The effect of fragmentation was idealized with predrilled holes. The thesis was written at the Structural Impact Laboratory (SIMLab) at NTNU in collaboration with the Norwegian Defence Estates Agency (NDEA).Tensile tests revealed a clearly anisotropic behavi...

  14. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    OpenAIRE

    Ivan Michalec; Milan Marônek

    2013-01-01

    Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  15. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    OpenAIRE

    Hamilta de Oliveira Santos; Marilene Morelli Serna; Nelson Batista de Lima; Isolda Costa; Jesualdo Luiz Rossi

    2005-01-01

    Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken f...

  16. A study of the chemisorption of a series of aminophenols on plasma-grown aluminium and magnesium oxides by IETS

    Science.gov (United States)

    Brown, N. M. D.; Taggart, G. M.

    Inelastic electron tunnelling spectroscopy (IETS) has been applied to study the adsorption of a series of aminophenols on plasma-grown aluminium and magnesium oxides. Vapour-phase doping of these surfaces was used and spectra recorded for 1,2-aminophenol, 1,3-aminophenol and 1,4-aminophenol. The tunnel spectra of the 1,2- and 1,3-aminophenols show that their chemisorption at both oxide surfaces is via reaction between phenolic and surface hydroxyl groups. For the 1,4-aminophenol example, adsorbate chemisorption involves transfer of surface-bound protons from the oxide in amino-group protonation. Some of these protons are replaced by deprotonation of the phenol at surface oxide ions. Observed band intensities for all three systems on aluminium oxide are held to be indicative of an adsorbate orientation on the surface which is close to the vertical. In contrast, those for magnesium oxide are more consistent with a non-vertical configuration.

  17. Study on the treatment of photovoltaic wastewater using electrocoagulation: Fluoride removal with aluminium electrodes-Characteristics of products

    International Nuclear Information System (INIS)

    In this work, treatment of synthetic fluoride-containing solutions by electrocoagulation method using aluminium electrodes has been studied. Electrocoagulation was investigated for applied potential (10-30 V), electrolysis time and supporting electrolyte (NaCl) concentration (0-100 mg/L). The results showed that with increasing applied potential and electrolysis time, the Al3+ dosage increases, and thereby favouring the fluoride ions removal. It was also observed that defluoridation is dependant on the concentration of supporting electrolyte. Finally, X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy of X-rays and Fourier transform infrared spectroscopy were used to characterize the solid products formed by aluminium electrodes during the EC process.

  18. Study on the treatment of photovoltaic wastewater using electrocoagulation: Fluoride removal with aluminium electrodes-Characteristics of products

    Energy Technology Data Exchange (ETDEWEB)

    Drouiche, N., E-mail: nadjibdrouiche@yahoo.fr [Silicon Technology Development Unit (UDTS), 2, Bd Frantz Fanon BP140, Alger-7-merveilles, 16200 (Algeria); Laboratory of Environmental Biotechnologies, Ecole Polytechnique d' Alger - 10, Avenue Pasteur El-Harrach (Algeria); Aoudj, S.; Hecini, M. [Silicon Technology Development Unit (UDTS), 2, Bd Frantz Fanon BP140, Alger-7-merveilles, 16200 (Algeria); Ghaffour, N. [Middle East Desalination Research Center, P.O. Box 21, P.C.133, Muscat (Oman); Lounici, H.; Mameri, N. [Laboratory of Environmental Biotechnologies, Ecole Polytechnique d' Alger - 10, Avenue Pasteur El-Harrach (Algeria)

    2009-09-30

    In this work, treatment of synthetic fluoride-containing solutions by electrocoagulation method using aluminium electrodes has been studied. Electrocoagulation was investigated for applied potential (10-30 V), electrolysis time and supporting electrolyte (NaCl) concentration (0-100 mg/L). The results showed that with increasing applied potential and electrolysis time, the Al{sup 3+} dosage increases, and thereby favouring the fluoride ions removal. It was also observed that defluoridation is dependant on the concentration of supporting electrolyte. Finally, X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy of X-rays and Fourier transform infrared spectroscopy were used to characterize the solid products formed by aluminium electrodes during the EC process.

  19. Evidence of dilute ferromagnetism in rare-earth doped yttrium aluminium garnet

    Energy Technology Data Exchange (ETDEWEB)

    Farr, Warrick G.; Goryachev, Maxim; Le Floch, Jean-Michel; Tobar, Michael E. [ARC Centre of Excellence for Engineered Quantum Systems, University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia); Bushev, Pavel [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany)

    2015-09-21

    This work demonstrates strong coupling regime between an erbium ion spin ensemble and microwave hybrid cavity-whispering gallery modes in a yttrium aluminium garnet dielectric crystal. Coupling strengths of 220 MHz and mode quality factors in excess of 10{sup 6} are demonstrated. Moreover, the magnetic response of high-Q modes demonstrates behaviour which is unusual for paramagnetic systems. This behaviour includes hysteresis and memory effects. Such qualitative change of the system's magnetic field response is interpreted as a phase transition of rare earth ion impurities. This phenomenon is similar to the phenomenon of dilute ferromagnetism in semiconductors. The clear temperature dependence of the phenomenon is demonstrated.

  20. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces.

    Science.gov (United States)

    Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

    2012-12-01

    Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy. PMID:22749723

  1. Effects of Aluminium Sulfate on Cadmium Accumulation in Rice

    International Nuclear Information System (INIS)

    Full text: Cadmium accumulation in Pathum Thani 1 and Suphan Buri 60 rice cultivars was investigated upon treatment with aluminium sulfate as a precipitant. Rice was grown hydroponically in a medium containing 4 ppm cadmium nitrate with or without 4 ppm aluminium sulfate. Root, stem with leaves and grain samples were collected and analyzed for cadmium content using atomic absorption spectroscopy and inductively coupled plasma atomic emission spectroscopy. Without the addition of aluminium sulfate, Pathum Thani 1 and Suphan Buri 60 accumulated 24.71∫ 3.14 ppm and 34.43 ∫ 4.51 ppm (dry weight of whole plant) of cadmium, respectively. With aluminium sulfate, cadmium accumulation increased to 40.66 ∫ 2.47 ppm and 62.94 ∫ 10.69 ppm, respectively. The addition of aluminium sulfate to the planting medium did not reduce cadmium accumulation but caused the rice to accumulate more cadmium especially in the shoots and grains. This observation might serve as the basis for future research on the management of agricultural areas that are contaminated with cadmium and aluminium

  2. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  3. Some features of ion mixing during simultaneous ion implantation and deposition of metallic coatings

    CERN Document Server

    Pogrebnyak, A D; Mikhalev, A D; Shablya, V T; Yanovskij, V P

    2001-01-01

    The results on the Ta, Cu ions implantation into the aluminium substrate by simultaneous deposition of these ions in the form of coatings are presented. The complex structure of these coatings from the given elements in the substrate, as well as the increase in the microhardness, adhesion and corrosion resistance growth are determined. It is shown on the basis of the results of the secondary ions energy distribution, that intermetallic phases are formed in the substrate surface layer

  4. Occupational exposure to beryllium in primary aluminium production.

    Science.gov (United States)

    Skaugset, Nils Petter; Ellingsen, Dag G; Dahl, Kari; Martinsen, Ivar; Jordbekken, Lars; Drabløs, Per Arne; Thomassen, Yngvar

    2012-02-01

    Alumina used in the production of primary aluminium contains Be which partly vaporises from the cryolite bath into the workroom atmosphere. Since Be may be toxic at lower exposure levels than previously thought, the personal exposure to Be among workers in 7 Norwegian primary smelters has been assessed. In total, 480 personal Respicon® virtual impactor full shift air samples have been collected during 2 sampling campaigns and analysed for water soluble Be, Al and Na using inductively coupled plasma optical emission spectrometry. In addition, water soluble F(-) has been measured by ion chromatography. The Be air concentrations in the inhalable, thoracic and respirable aerosol fractions have been calculated. The Be concentrations in the inhalable aerosol fraction vary between the different smelters. The highest GM concentration of Be in the inhalable fraction (122 ng m(-3), n = 30) was measured in the prebake pot room of a smelter using predominantly Jamaican alumina where also the highest individual air concentration of 270 ng m(-3) of Be was identified. The relative distribution of Be in the different aerosol fractions was fairly constant with the mean Be amount for the two sampling campaigns between 44-49% in the thoracic fraction expressed as % of the inhalable amount. Linear regression analysis shows a high correlation between water soluble Be, Al, F and Na describing an average measured chemical bulk composition of the water soluble thoracic fraction as Na(5.7)Al(3.1)F(18). Be is likely to be present as traces in this particulate matter by replacing Al atoms in the condensed fluorides and/or as a major element in a nanoparticle sized fluoride. Thus, the major amount of Be present in the work room atmosphere of Al smelter pot rooms will predominantly be present in combination with substantial amounts of water soluble Al, F and Na. PMID:21993554

  5. Development of biodegradable aluminium carboxymethylcellulose matrices for mosquito larvicides.

    Science.gov (United States)

    Mathew, Nisha; Kalyanasundaram, Muthuswami

    2004-07-01

    The use of ecofriendly biodegradable controlled-release formulations of mosquito larvicides could reduce the frequency of application and losses due to degradation of the insecticide compared with conventional formulations. Among the 20 matrices developed by entrapping the organophosphorus mosquito larvicide, fenthion, in carboxymethylcellulose ionotropically cross-linked with aluminium ions which were studied for release profiles, two matrices, CRF3b and CRF5b, were found to be stable for 16 and 14 weeks under simulated field conditions. The average concentration of fenthion released per week ranged from 0.06 to 3.5 mg litre(-1) for CRF3b and 0.09 to 2.72 mg litre(-1) for CRF5b. Of these two formulations, CRF3b was the more stable, maintaining the concentration of the active ingredient at the level required to effect mosquito control. The cumulative release of fenthion per pellet was 80% from CRF3b and 72% from CRF5b. Based on the study with fenthion, two similar matrices for triflumuron, a benzoylphenylurea insect growth regulator, STAR3b and STAR5b were developed. These matrices were stable up to 16 weeks with the average concentration of triflumuron released per week ranging from 0.05 to 3.44 mg litre(-1) for STAR3b and 0.07 to 2.71 mg litre(-1) for STARSb. The cumulative release of triflumuron per pellet was 75% from STAR3b and 76% from STAR5b. From the results of this study under simulated conditions, it is estimated that the application of four pellets of either fenthion or triflumuron per square metre of the breeding surface may play a useful role in controlling Culex quinquefasciatus Say in larval habitats for about 4 months. PMID:15260300

  6. Irradiation effects on aluminium and beryllium

    International Nuclear Information System (INIS)

    The High Flux Reactor (HFR) in Petten (The Netherlands) is a 45 MW light water cooled and moderated research reactor. The vessel was replaced in 1984 after more than 20 years of operation because doubts had arisen over the condition of the aluminium alloy construction material. Data on the mechanical properties of the aluminium alloy Al 5154 with and without neutron irradiation are necessary for the safety analysis of the new HFR vessel which is constructed from the same material as the old vessel. Fatigue, fracture mechanics (crack growth and fracture toughness) and tensile properties have been obtained from several experimental testing programmes with materials of the new and the old HFR vessel. 1) Low-cycle fatigue testing has been carried out on non-irradiated specimens from stock material of the new HFR vessel. The number of cycles to failure ranges from 90 to more than 50,000 for applied strain from 3.0% to 0.4%; 2) Fatigue crack growth rate testing has been conducted: - with unirradiated specimens from stock material of the new vessel; - with irradiated specimens from the remnants of the old core box. Irradiation has a minor effect on the sub-critical fatigue crack growth rate. The ultimate increase of the mean crack growth rate amounts to a factor of 2. However crack extension is strongly reduced due to the smaller crack length for crack growth instability (reduction of KIC). - Irradiated material from the core box walls of the old vessel has been used for fracture toughness testing. The conditional fracture toughness values KIQ ranges from 30.3 down to 16.5 MPa√m. The lowermost meaningful 'KIC' is 17.7 MPa√m corresponding to the thermal fluence of 7.5 1026 n/m2 for the End of Life (EOL) of the old vessel. - Testing carried out on irradiated material from the remnants of the old HFR core box shows an ultimate neutron irradiation hardening of 35 points increase of HSR15N and an ultimate tensile yield stress of 589 MPa corresponding to the ductility of 1

  7. Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

    Directory of Open Access Journals (Sweden)

    Senze Magdalena

    2015-03-01

    Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

  8. Oxidation of φ'-aluminium oxynitride

    International Nuclear Information System (INIS)

    Research highlights: Oxidation of φ'-AlON has been studied for the first time. First corrosion products are γ-alumina. Low density α-alumina is formed at high temperature. Grains are extensively cracked after oxidation. The low density of the α-alumina is due to a network of nanometric porosities. - Abstract: The oxidation in air of single crystal φ'-aluminium oxynitride (AlON) grains has been characterized by thermogravimetry and X-ray diffraction in the 1273-1673 K range. Two oxidation stages have been observed, suggesting the formation of a transitional phase. Below 1473 K, oxidation results in the apparition of platelets and noodle-like crystals on the surface of the initially faceted single crystals. Above 1473 K, low density α-alumina polycrystals start forming on the grain surface and grow towards the grain core with increasing temperature or time. Their low density is mainly due to the presence of a network of nano-porosities.

  9. A systematic review of aluminium phosphide poisoning.

    Science.gov (United States)

    Mehrpour, Omid; Jafarzadeh, Mostafa; Abdollahi, Mohammad

    2012-03-01

    Every year, about 300,000 people die because of pesticide poisoning worldwide. The most common pesticide agents are organophosphates and phosphides, aluminium phosphide (AlP) in particular. AlP is known as a suicide poison that can easily be bought and has no effective antidote. Its toxicity results from the release of phosphine gas as the tablet gets into contact with moisture. Phosphine gas primarily affects the heart, lungs, gastrointestinal tract, and kidneys. Poisoning signs and symptoms include nausea, vomiting, restlessness, abdominal pain, palpitation, refractory shock, cardiac arrhythmias, pulmonary oedema, dyspnoea, cyanosis, and sensory alterations. Diagnosis is based on clinical suspicion, positive silver nitrate paper test to phosphine, and gastric aspirate and viscera biochemistry. Treatment includes early gastric lavage with potassium permanganate or a combination with coconut oil and sodium bicarbonate, administration of charcoal, and palliative care. Specific therapy includes intravenous magnesium sulphate and oral coconut oil. Moreover, acidosis can be treated with early intravenous administration of sodium bicarbonate, cardiogenic shock with fluid, vasopresor, and refractory cardiogenic shock with intra-aortic baloon pump or digoxin. Trimetazidine may also have a useful role in the treatment, because it can stop ventricular ectopic beats and bigeminy and preserve oxidative metabolism. This article reviews the epidemiological, toxicological, and clinical/pathological aspects of AlP poisoning and its management. PMID:22450207

  10. Acute aluminium phosphide poisoning, what is new?

    Directory of Open Access Journals (Sweden)

    Yatendra Singh

    2014-01-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide that is commonly used for grain preservation. AlP has currently generated interest with increasing number of cases in the past four decades because of its increased use for agricultural and nonagricultural purposes, and also its easy availability in the markets has led to its increased misuse to commit suicide. Ingestion is usually suicidal in intent, uncommonly accidental and rarely homicidal. The poison affects all systems, shock, cardiac arrhythmias with varied ECG changes and gastrointestinal features being the most prominent. Diagnosis is made on the basis of clinical suspicion, a positive silver nitrate paper test to phosphine, and gastric aspirate and viscera biochemistry. Treatment includes early gastric lavage with potassium permanganate or a combination of coconut oil and sodium bicarbonate, administration of charcoal and palliative care. Specific therapy includes intravenous magnesium sulphate and oral coconut oil. Unfortunately, the lack of a specific antidote Results in very high mortality and the key to treatment lies in rapid decontamination and institution of resuscitative measures. This article aims to identify the salient features and mechanism of AlP poisoning along with its management strategies and prognostic variables.

  11. Fuzzy Multicriteria Ranking of Aluminium Coating Methods

    Science.gov (United States)

    Batzias, A. F.

    2007-12-01

    This work deals with multicriteria ranking of aluminium coating methods. The alternatives used are: sulfuric acid anodization, A1; oxalic acid anodization, A2; chromic acid anodization, A3; phosphoric acid anodization, A4; integral color anodizing, A5; chemical conversion coating, A6; electrostatic powder deposition, A7. The criteria used are: cost of production, f1; environmental friendliness of production process, f2; appearance (texture), f3; reflectivity, f4; response to coloring, f5; corrosion resistance, f6; abrasion resistance, f7; fatigue resistance, f8. Five experts coming from relevant industrial units set grades to the criteria vector and the preference matrix according to a properly modified Delphi method. Sensitivity analysis of the ranked first alternative A1 against the `second best', which was A3 at low and A7 at high resolution levels proved that the solution is robust. The dependence of anodized products quality on upstream processes is presented and the impact of energy price increase on industrial cost is discussed.

  12. Spectra of heliumlike carbon, aluminium and argon under strongly coupled plasma

    International Nuclear Information System (INIS)

    Spectral line positions for the highly stripped helium like carbon, aluminium and argon embedded in intense plasma environments have been calculated theoretically to compare with the existing data available from laser plasma experiments. The changes in the ionization potentials for such ions have been determined and the excitation energies, oscillator strengths and transition probabilities for the transitions 1s2 1S → 1snp 1P (n 2-5) have been evaluated for the diagnostic determination of such plasmas. The ion sphere (IS) model was used for estimating the effect of strongly coupled plasma on the ions within the non-relativistic as well as the relativistic framework. Time dependent perturbation theory has been applied for obtaining the linear response properties of the ions in the non-relativistic approximation. The effects of the plasma environment on such properties of the ions under the Debye screening model with suitable cut off radii have also been considered for comparing the data with those obtained from the IS model of the plasma. These results show that the IS model seems to be a viable method for predicting the data obtained from experiments involving strongly coupled plasmas generated in laser produced Icf plasmas

  13. Spectra of heliumlike carbon, aluminium and argon under strongly coupled plasma

    Energy Technology Data Exchange (ETDEWEB)

    Sil, A. [Heidelberg Univ., Theoretische Chemie (Germany); Anton, J. [Ulm Univ., Institut fur Elektrochemie (Germany); Fritzsche, S. [Gesellschaft fur Schwerionenforschung Darmstadt, Darmstadt (Germany); Mukherjee, P.K. [Indian Association for the Cultivation of Science, Jadavpur, Kolkata (India); Ramakrishna Mission Vivekananda Univ., West Bengal (India); Fricke, B. [Kassel Univ., Institut fur Physik (Germany)

    2009-12-15

    Spectral line positions for the highly stripped helium like carbon, aluminium and argon embedded in intense plasma environments have been calculated theoretically to compare with the existing data available from laser plasma experiments. The changes in the ionization potentials for such ions have been determined and the excitation energies, oscillator strengths and transition probabilities for the transitions 1s{sup 2} 1S -> 1snp {sup 1}P (n 2-5) have been evaluated for the diagnostic determination of such plasmas. The ion sphere (IS) model was used for estimating the effect of strongly coupled plasma on the ions within the non-relativistic as well as the relativistic framework. Time dependent perturbation theory has been applied for obtaining the linear response properties of the ions in the non-relativistic approximation. The effects of the plasma environment on such properties of the ions under the Debye screening model with suitable cut off radii have also been considered for comparing the data with those obtained from the IS model of the plasma. These results show that the IS model seems to be a viable method for predicting the data obtained from experiments involving strongly coupled plasmas generated in laser produced Icf plasmas

  14. Aluminium Matrix Composites Reinforced with Co-continuous Interlaced Phases Aluminium-alumina Needles

    Directory of Open Access Journals (Sweden)

    Elvio de Napole Gregolin

    2002-09-01

    Full Text Available An Al-5SiO2 (5 wt% of SiO2 aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si/Al2O3 interlaced structure named co-continuous composite. A technique of powder metallurgy, using commercial aluminium powder and the silica fibers as starting materials, followed by hot extrusion, was used to produce the composite. The co-continuous microstructure was obtained partially or totally on the fibers as a result of the reaction, which occurs during the heat treatment, first by solid diffusion and finally by the liquid Al-Si in local equilibrium, formed with the silicon released by reaction. The internal structure of the fibers was characterized using field emission electron microscope (FEG-SEM and optical microscopy on polished and fractured samples.

  15. Fabrication experience of aluminium clad aluminium matrix dispersion fuels at BARC

    International Nuclear Information System (INIS)

    Aluminium clad, aluminium matrix plate type dispersion fuels have been fabricated in BARC in recent years as part of fuel development programme for small non-power research reactors. The present paper describes the flowsheet developed for fabrication of Al-UAlx, Al-U3Si2 and Al-U3O8 fuels at BARC. The Al-20% U alloy fuel for KAMINI neutron radiography reactor was prepared by 'melting and casting' route, followed by picture framing and roll-bonding. For higher 'U' density fuels namely, Al-UAlx, Al-U3O8 and Al-U3Si2 the 'powder metallurgy' route was followed for preparation of fuel meat. The novel features in fabrication route were: addition of Zr for stabilizing UAl3 phase in Al-20% U alloy; x-ray radiography and microdensitometric scanning of radiographs for location of fuel outline inside fuel element and for confirming homogeneous distribution of fissile atoms; immersion ultrasonic testing for confirming good bonding between mating Al surface of the fuel plate. (author)

  16. Application of INAA for investigation of magnesium and aluminium oxide materials

    International Nuclear Information System (INIS)

    The paper presents investigations of changes in optical absorption and photo luminescence spectra of magnesium oxide, and natural and synthetic magnesium aluminium spinel related with the content of transition metal ions (Cr, Fe, Mn) and the irradiation with fast neutrons. Six synthetic single magnesium aluminium spinel crystals with different stoichiometry (MgO·nAl2O3), five natural crystals from Ural and Pamir deposits, and seven MgO crystals were studied. Micro impurities (Cr, Fe, and Mn) and macro component (Mg, Al) quantities have been determined using the instrumental neutron activation analysis technique. Concentrations of impurities in different spinels were found in following ranges: for Cr-1 × 10-4 to 8 × 10-2 %, for Mn-2 × 10-5 to 23 %, for Fe-1 × 10-4 to 1.2 %. Three ranges of luminescence: 380-460, 650-850 and 850-1,050 nm, were established in the most part of the investigated MgO samples. Analysis shows that the intensity of emission in each of these regions is strongly dependent on the concentration of transition metal ions. Great deviation from the stoichiometry of the irradiated MgO·2.8Al2O3 crystal leads to the local structure of α-Al2O3 formation around Cr3+ ions. The orange emission is attributed to Mn2+ in octahedral coordination, it can be assumed that the band at 570 nm is belonging to the complex centre 'Mn2+-F+ (or F centre)'. (author)

  17. Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

    Directory of Open Access Journals (Sweden)

    Mathivanan Periasamy

    2012-06-01

    Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

  18. Improving Efficiency of Aluminium Sacrificial Anode Using Cold Work Process

    Science.gov (United States)

    Asmara, Y. P.; Siregar, J. P.; Tezara, C.; Ann, Chang Tai

    2016-02-01

    Aluminium is one of the preferred materials to be used as sacrificial anode for carbon steel protection. The efficiency of these can be low due to the formation of oxide layer which passivate the anodes. Currently, to improve its efficiency, there are efforts using a new technique called surface modifications. The objective of this research is to study corrosion mechanism of aluminium sacrificial anode which has been processed by cold work. The cold works are applied by reducing the thickness of aluminium sacrificial anodes at 20% and 40% of thickness reduction. The cathodic protection experiments were performed by immersion of aluminium connected to carbon steel cylinder in 3% NaCl solutions. Visual inspections using SEM had been conducted during the experiments and corrosion rate data were taken in every week for 8 weeks of immersion time. Corrosion rate data were measured using weight loss and linear polarization technique (LPR). From the results, it is observed that cold worked aluminium sacrificial anode have a better corrosion performance. It shows higher corrosion rate and lower corrosion potential. The anodes also provided a long functional for sacrificial anode before it stop working. From SEM investigation, it is shown that cold works have changed the microstructure of anodes which is suspected in increasing corrosion rate and cause de-passivate of the surface anodes.

  19. The structure of high-quality aluminium cast iron

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2012-01-01

    Full Text Available In this study presents the analyse of aluminium iron cast structure (as-cast condition which are used in high temperature. While producing the casts of aluminium iron major influence has been preserve the structure of technological process parameters. The addition to Fe-C-Al alloy V, Ti, Cr leads to the improvement of functional and mechanical cast qualities. In this study, a method was investigated to eliminate the presence of undesirable Al4C3 phases in a aluminium cast iron structure and thus improve the production process. V and Ti additions in aluminium cast iron allows to development of FeAl - VC or TiC alloys. In particular, V or Ti contents above 5 wt.% were found to totally eliminate the presence of Al4C3. In addition, preliminary work indicates that the alloy with the FeAl - VC or TiC structure reveals high oxidation resistance. The introduction of 5 wt.% chromium to aluminium cast iron strengthened Al4C3 precipitate. Thus, the resultant alloy can be considered an intermetallic FeAl matrix strengthened by VC and TiC or modified Al4C3 reinforcements.

  20. Corrosion of aluminium metal in OPC- and CAC-based cement matrices

    Energy Technology Data Exchange (ETDEWEB)

    Kinoshita, Hajime, E-mail: h.kinoshita@sheffield.ac.uk [Department of Materials Science and Engineering, The University of Sheffield, Mappin Street, Sheffield, S1 3JD (United Kingdom); Swift, Paul; Utton, Claire [Department of Materials Science and Engineering, The University of Sheffield, Mappin Street, Sheffield, S1 3JD (United Kingdom); Carro-Mateo, Beatriz [The Public University of Navarra, C/Esquíroz, 30 trasera, Pamplona 31007 (Spain); Marchand, Geraldine [The National Institute of Applied Sciences (INSA) Lyon, 20 Avenue Albert Einstein 69621 Villeurbanne Cedex (France); Collier, Nick [National Nuclear Laboratory, Chadwick House, Birchwood Park, Warrington, WA3 6AE (United Kingdom); Milestone, Neil [Industrial Research Ltd., 69 Gracefield Road, Lower Hutt, 5040 (New Zealand)

    2013-08-15

    Corrosion of aluminium metal in ordinary Portland cement (OPC) based pastes produces hydrogen gas and expansive reaction products causing problems for the encapsulation of aluminium containing nuclear wastes. Although corrosion of aluminium in cements has been long known, the extent of aluminium corrosion in the cement matrices and effects of such reaction on the cement phases are not well established. The present study investigates the corrosion reaction of aluminium in OPC, OPC-blast furnace slag (BFS) and calcium aluminate cement (CAC) based systems. The total amount of aluminium able to corrode in an OPC and 4:1 BFS:OPC system was determined, and the correlation between the amount of calcium hydroxide in the system and the reaction of aluminium obtained. It was also shown that a CAC-based system could offer a potential matrix to incorporate aluminium metal with a further reduction of pH by introduction of phosphate, producing a calcium phosphate cement.

  1. Residual stress in 7449 aluminium alloy forgings

    International Nuclear Information System (INIS)

    The through thickness residual stress distributions within three 120 mm thick rectilinear forgings, made from the high strength aluminium alloy 7449 have been measured using both neutron diffraction and deep hole drilling. Neutron diffraction measurements were made on two instruments, one using a pulsed spallation neutron source, the other a steady state reactor source. Heat treatment of the forgings included a rapid quench into cold water and it was the residual stresses arising from this step that were initially measured. Neutron diffraction measurements indicated large magnitude (>250 MPa) tensile residual stresses in the centre of an as quenched forging, balanced by surface regions stressed in compression (<-200 MPa). Sufficient measurements were made to permit the description of the residual stress distribution using area maps. Two forgings were stress relieved by cold compression immediately after quenching. The degree of plastic strain was either 2.5% or 4%, and was applied by a single application of force in the short transverse direction. Cold compressed forgings were found to have far lower residual stress when compared to the as quenched condition. The amount of cold compression was found to cause an insignificant difference in the final residual stress distribution. The neutron diffraction results are compared to measurements made by deep hole drilling and a new incremental variation of the technique. The deep hole was drilled through the centre of the forgings in the short transverse direction. Multiple neutron diffraction measurements were also made on the extracted cores from the deep hole measurements to assess the variation of the unstrained lattice parameter through the thickness of the forgings.

  2. PEMBINAAN PENGERAJIN BOKOR ALUMINIUM DI DESA MENYALI

    Directory of Open Access Journals (Sweden)

    I NYOMAN GDE ANTARA, dkk.

    2014-04-01

    Full Text Available Alluminium bowl craft industrial center is located in Menyali village Sawan district Buleleng regency of Bali province. In this business development, they faced some problems such as increasingly expensive alluminium plate raw materials, decreasing selling product prices due to competition among craftsmen, difficulty in extending the marketing, lack of capital, lack of knowledge in business management, and lack of technical capacity and production innovation. Currently the organization has been formed aluminum bowl craftsmen groups, they are “Sumber Urip” and “Sumur Jaya”. This organization is still limited to tradisional associations such as a community organization, has not led to organize in a micro-enterprise or cooperation. Their organization management should not be arranged. Therefore, they need helps from the government and other institutions to build this bowl craftsmen in developing their businesses through a group of micro-enterprises or cooperations. Wishly, with formal business entity that would facilitate access to a variety of coaching and help governments andother institutions. From the SWOT analysis, it is found some problems and solutions that should be done. Alluminium bowl craftsmen groups, named “Sumber Urip” and “Sumur Jaya” is not in the form of business entity or cooperation yet, so that the results of coaching have agreed to form a cooperation. Venture capital assistance for the development and production are still needed and to be an absolute given, but a way to market more absolute yield is given, through participation in various events exhibition to introduce the product is expected to expandits market share up to overseas or exports. In the production process it has been introduced that is appropriate technology for instant a rolling tool to make a wiring groove on the outside of the bowl, so that it will simplify and speed up the process, especially by aged mothers.Keywords: aluminium bowl, Menyali

  3. Low Speed Laser Welding of Aluminium Alloys Using Single-Mode Fiber Lasers

    OpenAIRE

    Tu, Jay; Paleocrassas, Alexander

    2010-01-01

    In this chapter, topics related to extending fiber laser welding of aluminium in the low speed range were discussed. General topics, such as the properties of aluminium and welding defects, review of high speed laser welding of aluminium, and fiber laser characteristics and optical setups for safety, were first reviewed. Recent research results on the modelling and validation of laser welding of aluminium, experimental characterization of low speed welding processes, and the instability pheno...

  4. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    OpenAIRE

    Zauzi, N. S. Ahmad; M. Z. H. Zakaria; Baini, R.; Rahman, M. R.; N. Mohamed Sutan; Hamdan, S

    2016-01-01

    Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH) on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipita...

  5. The determination of boron in high-purity aluminium metal by spark-source mass spectrometry

    International Nuclear Information System (INIS)

    A method is described for the determination of boron in high-purity aluminium metal. Both isotopic boron lines (10B+1 and 11B+1) are used for the analysis. As there are no low-abundance isotopic lines for aluminium, measurements were made direct without reference to aluminium as an internal standard. The boron concentration values of eight aluminium samples analysed by this method compared favourably with results obtained from other techniques

  6. Aluminium salen and salan catalysts for polymerisation of novel monomers and macrostructures

    OpenAIRE

    MacDonald, Jarret Preston

    2016-01-01

    Aluminium salen and aluminium salan complexes are excellent catalysts for the ring-opening polymerisation of lactide. This thesis studied their efficacy in the polymerisation of novel monomers and their ability to build new macrostructures. Aluminium salen and aluminium salan complexes were tested as catalysts for ring-opening polymerisation of common aliphatic monomers where controlled polymer synthesis has not yet been achieved with similar systems. Excellent control over ...

  7. IEC 61267: Feasibility of type 1100 aluminium and a copper/aluminium combination for RQA beam qualities.

    Science.gov (United States)

    Leong, David L; Rainford, Louise; Zhao, Wei; Brennan, Patrick C

    2016-01-01

    In the course of performance acceptance testing, benchmarking or quality control of X-ray imaging systems, it is sometimes necessary to harden the X-ray beam spectrum. IEC 61267 specifies materials and methods to accomplish beam hardening and, unfortunately, requires the use of 99.9% pure aluminium (Alloy 1190) for the RQA beam quality, which is expensive and difficult to obtain. Less expensive and more readily available filters, such as Alloy 1100 (99.0% pure) aluminium and copper/aluminium combinations, have been used clinically to produce RQA series without rigorous scientific investigation to support their use. In this paper, simulation and experimental methods are developed to determine the differences in beam quality using Alloy 1190 and Alloy 1100. Additional simulation investigated copper/aluminium combinations to produce RQA5 and outputs from this simulation are verified with laboratory tests using different filter samples. The results of the study demonstrate that although Alloy 1100 produces a harder beam spectrum compared to Alloy 1190, it is a reasonable substitute. A combination filter of 0.5 mm copper and 2 mm aluminium produced a spectrum closer to that of Alloy 1190 than Alloy 1100 with the added benefits of lower exposures and lower batch variability. PMID:26776501

  8. Behaviour of painted aluminium in Ibero-American atmosphere

    International Nuclear Information System (INIS)

    Aluminium generally presents good corrosion resistance to the atmosphere. However, unprotected aluminium and aluminium alloys weather outdoors to an ugly grey colour, which deepens to black in industrial atmospheres, and undergo superficial pitting in marine atmospheres, etc. Finishing technologies are applied for their protection and decoration in a wide range of applications. These technologies basically consist of two protection processes: anodizing and painting: the latter going from conventional solvent base paints to modern water-born, high solids and powder coatings. This paper considers the weathering performance of three paint systems: alkyl, polyurethane and polyester, after more than three years of exposure in a wide spectra of Ibero-American atmospheric conditions. The information reported includes resistance to undercutting corrosion at the scribe, filiform corrosion, fungal attack and change in the physico-chemical properties of the paint surface (loss of gloss, colour changes, chalking, etc.). (Author) 9 refs

  9. Sensitivity analysis on ultimate strength of aluminium stiffened panels

    DEFF Research Database (Denmark)

    Rigo, P.; Sarghiuta, R.; Estefen, S.; Lehmann, E.; Otelea, S. C.; Pasqualino, I.; Simonsen, Bo Cerup; Wan, Z.; Yao, T.

    2003-01-01

    This paper presents the results of an extensive sensitivity analysis carried out by the Committee III.1 "Ultimate Strength" of ISSC?2003 in the framework of a benchmark on the ultimate strength of aluminium stiffened panels. Previously, different benchmarks were presented by ISSC committees on...... ultimate strength. The goal has typically been to give guidance to the designer on how to predict the ultimate strength and to indicate what level of accuracy would be expected. This time, the target of this benchmark is to present reliable finite element methods to study the behaviour of axial compressed...... stiffened aluminium panels (including extruded profiles). Main objectives are to compare codes/models and to perfom quantitative sensitivity analysis of the ultimate strength of a welded aluminium panel on various parameters (typically the heat-affected zone). Two phases were planned. In Phase A, alle...

  10. Aluminium toxicity in the rat liver and brain

    International Nuclear Information System (INIS)

    To investigate the etiology of Alzheimer's disease, we examined the brain and liver tissue uptake of aluminium 5-75 days after aluminium injection into healthy rats. Ten days after the last injection, Al was detected in the brain and the brain cell nuclei by particle-induced X-ray emission (PIXE) analysis. Al was also demonstrated in the liver and the liver cell nuclei by PIXE analysis and electron energy loss spectrometry (EELS). The morphological changes of the rat brain examined 75 days after the injection were similar to those which have been reportedly observed in the brain of patients with Alzheimer's disease. These results support the theory that Alzheimer's disease is caused by irreversible accumulation of aluminium in the brain, as well as the nuclei of brain cells. (orig.)

  11. Comparative performance of aluminium copper and iron solar stills

    International Nuclear Information System (INIS)

    Three different metal sheets have been used in the fabrication of three different single sloping solar stills of the same surface geometry. The metals were galvanized iron, aluminium and copper. This paper presents the performance of the different stills operating under the same environmental conditions. The observed distillate yields was greatest for copper, then aluminium and lastly, iron still. The differences in the yields is attributed to the differences in the thermal conductivities of the metals. The equivalent local costs for the fabrication of the copper, aluminium and iron stills are respectively $160, $95 and $60. Taking the long run costs into consideration, the copper still is preferred because of its availability, durability, weldability and relatively higher conductivity of 380Wm-1K-1 value. (author). 9 refs, 2 figs, 2 tabs

  12. Pressureless sintered silicon carbide tailored with aluminium nitride sintering agent

    International Nuclear Information System (INIS)

    This study reports the influence of aluminium nitride on the pressureless sintering of cubic phase silicon carbide nanoparticles (β-SiC). Pressureless sintering was achieved at 2000 degrees C for 5 min with the additions of boron carbide together with carbon of 1 wt% and 6 wt%, respectively, and a content of aluminium nitride between 0 and 10 wt%. Sintered samples present relative densities higher than 92%. The sintered microstructure was found to be greatly modified by the introduction of aluminium nitride, which reflects the influence of nitrogen on the β-SiC to α-SiC transformation. The toughness of sintered sample was not modified by AlN incorporation and is relatively low (around 2.5 MPa m1/2). Materials exhibited transgranular fracture mode, indicating a strong bonding between SiC grains. (authors)

  13. Reflection of infrared radiation from thin aluminium layers

    CERN Document Server

    Calatroni, Sergio

    2001-01-01

    The thermal shielding of the LHC magnets cryostats will make use of Multi-Layer Insulation. This is a sandwich of several Mylar (polyester) foils 6 µm thick coated with a thin film of aluminium, having a thickness of some 30 nm. The thickness of the aluminium film must be kept at a minimum to minimise lateral thermal conduction. The outer layer of this sandwich stays at a temperature of 20 K or below, and receives IR radiation from surfaces at 77 K (wavelength of 37.6 µm at the peak of blackbody radiation), which should be reflected with the highest efficiency. The minimum thickness for the aluminium layer to avoid transmission of the radiation can be calculated by making use of the skin effect theory, taking into account the changes in electrical properties that are due to the extremely low thickness of the film.

  14. Chapter 12. The initial aluminium as a raw material for goods

    International Nuclear Information System (INIS)

    The aluminium-raw product and methods of its refining including sedimentation, refining by inert gases and by fluxes was considered. The chemical composition of commodity aluminium was considered as well. The initial processing of aluminium-raw product was studied

  15. Bakable aluminium vacuum chamber and bellows with an aluminum flange and metal seal for ultrahigh vacuum

    International Nuclear Information System (INIS)

    A bakable (2000C) aluminium alloy vacuum chamber and bellows (6063-T6) with an aluminium alloy (2219-T87) flange and metal seal (Helicoflex-HN: aluminium O-ring) has been constructed. Such components may be used in the assemblies of the vacuum chambers in proton synchrotrons and electron storage rings

  16. Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

    NARCIS (Netherlands)

    Regnier, Marie; Metz, Bernard; Tilstra, Wichard; Hendriksen, Coenraad; Jiskoot, Wim; Norde, Willem; Kersten, Gideon

    2012-01-01

    Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide p

  17. Characterisation of Ga-coated and Ga-brazed aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Ferchaud, E. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Christien, F., E-mail: frederic.christien@univ-nantes.fr [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France); Barnier, V. [Ecole Nationale Superieure des Mines, MPI, CNRS UMR5146, Centre SMS, 158 Cours Fauriel, 42023 Saint Etienne (France); Paillard, P. [Universite de Nantes, Polytech' Nantes, Laboratoire Genie des Materiaux et Procedes Associes, Rue Christian Pauc, 44306 Nantes Cedex 3 (France)

    2012-05-15

    This work is devoted to the brazing of aluminium using liquid gallium. Gallium was deposited on aluminium samples at {approx} 50 Degree-Sign C using a liquid gallium 'polishing' technique. Brazing was undertaken for 30 min at 500 Degree-Sign C in air. EDS (Energy Dispersive X-ray Spectroscopy) and AES (Auger Electron Spectroscopy) characterisation of Ga-coated samples has shown that the Ga surface layer thickness is of ten (or a few tens of) nanometres. Furthermore, aluminium oxide layer (Al{sub 2}O{sub 3}) was shown to be 'descaled' during Ga deposition, which ensures good conditions for further brazing. Cross-section examination of Ga-coated samples shows that liquid gallium penetrates into the aluminium grain boundaries during deposition. The thickness of the grain boundary gallium film was measured using an original EDS technique and is found to be of a few tens of nanometres. The depth of gallium grain boundary penetration is about 300 {mu}m at the deposition temperature. The fracture stress of the brazed joints was measured from tensile tests and was determined to be 33 MPa. Cross-section examination of brazed joints shows that gallium has fully dissolved into the bulk and that the joint is really autogenous. - Highlights: Black-Right-Pointing-Pointer Aluminium can be brazed using liquid gallium deposited by a 'polishing' technique. Black-Right-Pointing-Pointer The aluminium oxide layer is 'descaled' during liquid Ga 'polishing' deposition. Black-Right-Pointing-Pointer EDS can be used for determination of surface and grain boundary Ga film thickness. Black-Right-Pointing-Pointer The surface and grain boundary Ga film thickness is of a few tens of nm. Black-Right-Pointing-Pointer Surface and grain boundary gallium dissolves in the bulk during brazing.

  18. Modification of surface and barrier properties of polyethylene terephthalate and polycarbonate plastics by ion implantation

    International Nuclear Information System (INIS)

    Full text: Surface properties of two commercial plastics, SKYPET-BB polyethylene terephthalate (PET) film and Lexan (Polycarbonate) sheet, have been modified by implanting aluminium, silicon, nitrogen and hydrogen ions into samples of the plastics. Aluminium and silicon ions were implanted into the PET and Lexan samples at three different dose levels using a Metal Vapour Vacuum Arc Ion Source implantation system. Hydrogen and nitrogen ions were implanted at two different dose levels in a Plasma Immersion Ion Implantation Facility. Diffusion rates of Helium through the PET samples were determined at 19 deg C for pressures of He from 0.5 to 2.5atm. The diffusion rates of helium through the aluminium and silicon implanted samples were much lower than the diffusion rate through the unimplanted PET; nitrogen implantation had little effect. Copyright (2005) Australian Institute of Physics

  19. Aging of maraging steel welds during aluminium alloy die casting

    OpenAIRE

    Klobčar, Damjan; Pleterski, Matej; Taljat, Boštjan; Kosec, Ladislav; Tušek, Janez

    2015-01-01

    The aim of this study is to evaluate precipitation annealing of 18% Ni maraging steel repair welds during aluminium die casting and to predict the prolonged in-service tool life. The emphasis of this study is the influence ofpost-weld precipitation annealing heat treatment and aluminium die casting thermal cycling on metallurgical and mechanical properties. A series of specimens of 1.2344 tool steel is prepared to which 1.6356 maraging steel is GTA weld cladded. Analysis of weld microstructur...

  20. Zinc- and aluminium making processes using HTGR process heat

    International Nuclear Information System (INIS)

    The high temperature gas-cooled reactor (HTGR) has frequently been suggested as a source of process heat for steel-making; now it has been suggested that it could also be used in the zinc- and aluminium-making processes. For that purpose, several procedures are proposed whereby the key steps in the reduction of zinc oxyde are the use of a gas produced and heated by the HTGR process heat source. Also for the aluminium making process a series of new techniques in connection with the Toth and Grothe processes, coupled to a HTGR, are discussed. (orig.)

  1. The hydrolysis of aluminium, a mass spectrometric study

    OpenAIRE

    Sarpola, A.

    2007-01-01

    Abstract This thesis is focused on the hydrolysis of aluminium, the polymerisation of the hydrolysis products, and how these can be monitored by mass spectrometric methods. The main aim of this research is to figure out how the aqueous speciation of aluminium changes as a function of pH (3.2–10), concentration (1–100 mM), reaction time (1s–14d), and counter anion (Cl-, SO42-, HCOO-). The method used was electrospray mass spectrometry. The results showed more variable speciation than those ...

  2. Power quality results in energy efficient aluminium smelter operation

    Energy Technology Data Exchange (ETDEWEB)

    Wiestner, Max

    2010-09-15

    New aluminium smelters consume up to 2400MW of electrical energy making the energy efficiency aspect most important. Power quality, optimised power conversion systems and well engineered power plant interfaces are essential for highest energy efficiency. An early optimisation of the power system design will reduce the capital investment cost for the power plant and smelter substation as well as results in most energy efficient aluminium production. This paper describes and intends to discuss the power quality improvement concepts and designs as well as energy cost reduction opportunities which a high power quality system can achieve.

  3. Separation of 35S-sulfate on neutral aluminium oxide

    International Nuclear Information System (INIS)

    The results of 35S-sulfate chromatography on neutral aluminium oxide (γ-Al2O3) are presented. Possibility of quantitative adsorption of 35S-sulfate on Al2O3 from acidic or neutral potassium chloride solutions of high concentration is shown. Dynamic adsorption capacity of neutral aluminium oxide with respect to sulfate from weakly acidic potassium chloride solution equals near 10 μmol/ml of adsorbent. Optimal parameters for chromatographic isolation of 35S-sulfate without carrier from irradiated KCl target are determined. (author)

  4. Lubricated sliding wear behaviour of aluminium alloy composites

    OpenAIRE

    J. C. Walker; Rainforth, W. M.; Jones, H.

    2005-01-01

    Interest in aluminium alloy (Al-alloy) composites as wear resistant materials continues to grow. However, the use of the popular Al-alloy-SiC composite can be limited by the abrasive nature of the SiC, leading to increased counterface wear rates. This study reports new Al-alloy composites that offer high wear resistance, to a level similar to Al-alloy-SiC. Aluminium alloy (2124, 5056) matrix composites reinforced by nominally 15 vol.% of Cr3Si, MoSi2, Ni3Al and SiC particles were prepared by ...

  5. Determination of cadmium in aluminium by atomic absorption spectrometry

    International Nuclear Information System (INIS)

    A direct method for the determination of cadmium in elemental aluminium is described. Metal samples are dissolved in diluted hydrochloric acid and cadmium is determined by atomic absorption spectrometry in an air-acetylene flame. Interference by non-specific absorption observed at the analytical wavelength incorrected for by means of a non-absorbing line emitted by the hollow-cathode lamp. Relatively large amounts of arsenic do not interfere. The minimun determinable concentration of cadmium for this procedure is 2-3 ppm, expressed on aluminium basis. (author)

  6. Electrochemical noise from corroding carbon steel and aluminium

    International Nuclear Information System (INIS)

    Electrochemical noise measurements were conducted on carbon steel and aluminium in sodium chloride solutions. Noise parameters like standard deviation of potential and current, noise resistance, pitting index, noise power were studied for the purpose of measuring corrosion rate. These parameters compared well with the corrosion rate. Pitting index was not very reliable. Current noise was more close to the corrosion rates. General corrosion gave rise to white noise type of power spectrum while flicker noise type of spectrum was obtained from pitting attack. Sodium nitrite is shown to inhibit the corrosion of carbon steel. Aluminium corrodes in the early period of exposure and passivates during long exposure

  7. Bioactive type glass-ceramics within incorporated aluminium

    International Nuclear Information System (INIS)

    Bioactive glass-ceramics are used as biomaterials for the reparation of bone tissue. They are prepared, generally, by bioglass of specific composition for each particular use. The aluminium addition in the formulation at very small quantities influences on the structural properties. Two glass-ceramics obtained by P2O5-Na2O-CaO-SiO2 formulation within aluminium (0.5 % in Al2O3 base) added through a reactive alumina and purified feldspar were analyzed. The results showed structural differences between both glass-ceramics. (author)

  8. Monitoring of slurry fields solutions of aluminium production

    International Nuclear Information System (INIS)

    Results of annual monitoring of slurry fields solutions of aluminium industrial production of Tajik Aluminium Plant are considered in this work. It is found that in summer period the containing of sulfate, carbonate, hydro carbonate and fluoride salts in slurry fields solutions increase. This is due to intensive evaporation of solvent (water). In autumn-winter period due to air temperature decreasing the precipitation of above mentioned salts is observed. The results of chemical analysis of slurry fields solutions are presented in this work. The slurry fields solutions are analyzed by means of X-ray and thermal analysis. The flowsheet of purification of processed slurry fields solutions from sodium sulphate is proposed.

  9. Marker behaviour of implanted xenon during the anodic oxidation of aluminium: evidence and interpretation of dose dependant splitting effect

    International Nuclear Information System (INIS)

    Using 2 MeV lithium ions backscattering and transmission electron microscopy techniques, a part of xenon atoms introduced by implantation in aluminium metal under the initial oxide layer is shown to be tranported by the moving metal-oxide interface during anodic oxidation. From specific anodization conditions (V sup(ct), T = 900C) this splitting of the initial xenon distribution is interpreted in terms of bubble formation and growth above a given local concentration threshold. A schematic model for this behaviour evolution is proposed. This dose dependance is of practical interest in the determination of transport numbers. Although unambiguously measured they may be subject to significant systematic uncertainties which are discussed

  10. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    International Nuclear Information System (INIS)

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg (AlMg3) and Al-1.1%Mg-0.5%Si (Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-1000C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) showed a complete absence of voids or bubbles in the grain interiors of the aluminium and the aluminium-alloys. Bubbles were clearly visible by TEM at grain boundaries in pure Al and the AlMg3 alloy; but bubbles were not visible in the Al6061 alloy. The bubble density in the AlMg3 alloy was considerably higher than in pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure. (orig.)

  11. Accumulation of Aluminium and Physiological Status of Tree Foliage in the Vicinity of a Large Aluminium Smelter

    Directory of Open Access Journals (Sweden)

    E. D. Wannaz

    2012-01-01

    Full Text Available A pollution gradient was observed in tree foliage sampled in the vicinity of a large aluminium production facility in Patagonia (Argentina. Leaves of Eucalyptus rostrata, and Populus hybridus and different needle ages of Pinus spec. were collected and concentrations of aluminium (Al and sulphur (S as well as physiological parameters (chlorophyll and lipid oxidation products were analyzed. Al and S concentrations indicate a steep pollution gradient in the study showing a relationship with the physiological parameters in particular membrane lipid oxidation products. The present study confirms that aluminium smelting results in high Al and sulphur deposition in the study area, and therefore further studies should be carried out taking into account potentially adverse effects of these compounds on human and ecosystem health.

  12. Range parameters of aluminium implants in medium and heavy mass metals

    Science.gov (United States)

    Hayes, M.; Hauser, T.; Friedland, E.; Thugwane, S. J.; Malherbe, J. B.; Naidoo, S. R.

    2000-03-01

    Nuclear reaction analysis was used to determine the range profiles of 150 keV aluminium ions implanted into a variety of metal targets in the atomic number region of 23⩽Z 2⩽78 . Implantations were performed at room temperature with fluences of 5×10 16 Al + cm -2 and dose rates below 10 13 Al + cm -2 s -1 to prevent excessive target heating. Profiles were determined by detecting the 10.76 MeV photons from the 27Al(p,γ) 28Si resonance reaction at 992 keV as a function of proton energy. Range profiles were extracted from the excitation curve after correcting for proton straggling. The experimental profiles and range moments are compared with TRIM predictions, taking target sputtering effects into account.

  13. On Phonons in Simple Metals II. Calculated Dispersion Curves In Aluminium

    International Nuclear Information System (INIS)

    The real part of the dynamical matrix, derived earlier in a weak local potential ion-electron interaction model of the metal, is investigated in the case of aluminium. It is shown that the free electron, or Lindhard, dielectric function leads to a picture of the metal which is inconsistent with the dHvA observations of the Fermi surface. By adjusting one parameter, however, the experimental phonon frequencies are reproduced satisfactorily. Even some simple structure in the derivative dω/dq can be reproduced in this way. Although corrections to the Lindhard dielectric matrix give no essential contributions to the dynamical matrix, the first order corrections, which are the most important, can explain the observed Fermi surface. Much of the observed structure in the phonon dispersion curves seems also to be due to these non-diagonal terms in the dielectric matrix

  14. A gaseous proportional counter built from a conventional aluminium beverage can

    CERN Document Server

    Winkler, Alexander; Hildén, Timo; Garcia, Francisco; Fedi, Giacomo; Devoto, Francesco; Brücken, Erik J

    2015-01-01

    The gaseous proportional counter is a device that can be used to detect ionizing radiation. These devices can be as simple as a cylindrical cathode and a very thin anode wire centered along its axis. By applying a high voltage, a strong electric field is generated close to the anode wire. Ion-pairs, generated by passing ionizing radiation, create avalanches once they drift into the strong electric field region near the anode. The electrical charges created by the avalanche generate an observable signal which is proportional to the energy loss of the incoming radiation. We discuss the construction of such a device. Our detector was built from an ordinary aluminium beverage can and uses a common electric wire strand as the anode. The construction of this detector offers students at universities or technically oriented high schools a detailed understanding of the design and operation of gaseous radiation detectors. The equipment required to complete the project should be available at most institutions.

  15. Protection against corrosion in marine environments of AA6060 aluminium alloy by cerium chlorides

    International Nuclear Information System (INIS)

    Lanthanide salts are being considered as an environmentally friendly alternative to the classic systems based on chromates. The addition of small concentrations of cerium chloride to aerated aqueous 3.5% NaCl solution inhibits uniform and pitting corrosion processes of AA6060. Full immersion tests combined with different electrochemical techniques were involved to determine the protection degree and the inhibition character supplied by the cerium ion. Their microscopic and compositional features have been analyzed using SEM and EDS spectra. The results obtained show that the protective layer has heterogeneous composition. An alumina layer covers the aluminium matrix while dispersed cerium-rich islands deposited over the cathodic sites of the alloy. In the case of AA6060, α-Al(Fe,Mn)Si acts as permanent cathodic sites.

  16. Investigation on the role of air in the dynamical evolution and thermodynamic state of a laser-induced aluminium plasma by spatial- and time-resolved spectroscopy

    International Nuclear Information System (INIS)

    The amount and the spatial distribution of air atoms and ions in a laser-induced plasma in ambient air provide important information about the formation of the plasma and its successive evolution history. For this reason, in the present work, the air mixing in a laser-induced plasma in air at atmospheric pressure and its influence on its thermodynamic evolution were studied. Information about spatial distributions of atoms and ions from Al, N and O were achieved by Abel-inverted spectra in the plume. The occurrence of LTE in the plume was also assessed by the utilization of theoretical criteria, and by the analysis of experimental spectra. Aluminium atoms and ions were found to be in LTE, while nitrogen and oxygen were not because of their longer times of relaxation toward equilibrium. Nitrogen was found to be over-ionized with respect to Saha-Eggert equilibrium, indicating that the plasma is recombining. Experimental observations suggest that the concentration of air species in the plasma is larger than that of aluminium, even in the region closer to the target, where the aluminium lines are stronger. In the front part of the plume only emission lines from air species were observed. The results suggest that a Laser-Supported Detonation (LSD) regime occurs during the trailing part of the laser pulse, resulting in the strong inclusion into the plasma of air elements. In this scenario, also the thermodynamic history of the plume is affected by the predominance of air species.

  17. Corrosion of aluminium alloy test coupons in the TRIGA Mark III Research Reactor of Mexico

    International Nuclear Information System (INIS)

    The results of corrosion studies developed in the Instituto Nacional de Investigaciones Nucleares (ININ) are presented. The extent of corrosion of the aluminium alloy coupons exposed to the water of ININ TRIGA reactor pool was not significant. Few pits and oxides were observed on the coupon surfaces immersed for different times. This reduced extent of corrosion was similar to those on coupons exposed at other sites as per data obtained by visual inspection, metallographic analysis and image analysis. The water chemistry in the reactor pool was monitored throughout the duration of the project. The main parameters that influence the corrosion of Al alloy fuel cladding were measured. The conductivity of the water in the reactor pool was 1-3 μS/cm, within recommended values to avoid corrosion. The chloride ion concentration was maintained below 1 ppm. Others ions (sulphates, calcium, nitrates) were also below 1 ppm. Another parameter that was measured was the amount of settled solids on coupon surfaces and their influence on corrosion. The sedimentation rate in the TRIGA Reactor pool was 17.66 μg/cm2 and the sediment composition indicated iron oxides, aluminium-silicon compounds and some calcium carbonates. The sedimentation rate was similar in magnitude to that at other storage sites. However, the corrosion racks in the ININ TRIGA Reactor were exposed to high water flow rates, 1324.5 l/min. This high flow rate is considered to reduce the amount of deposited solids on coupon surfaces. The particles deposited on the coupon surfaces influenced pit initiation. (author)

  18. Experimental weathering rates of aluminium silicates

    International Nuclear Information System (INIS)

    The chemical weathering of primary rocks and minerals in natural systems has a major impact on soil development and its composition. Chemical weathering is driven to a large extent by mineral dissolution. Through mineral dissolution, elements are released into groundwater and can readily react to precipitate secondary minerals such as clays, zeolites, and carbonates. Carbonates form from divalent cations (e.g. Ca, Fe and Mg) and CO2, and kaolin clay and gibbsite formation is attributed to the weathering of aluminium-rich minerals, most notably the feldspars. The CarbFix Project in Hellisheidi (SW-Iceland) aims to use natural weathering processes to form carbonate minerals by the re-injection of CO2 from a geothermal power plant back into surrounding basaltic rocks. This process is driven by the dissolution of basaltic rocks, rich in divalent cations, which can combine with injected CO2 to form and precipitate carbonates. This thesis focuses on the dissolution behaviour of Stapafell crystalline basalt, which consists of three major phases (plagioclase, pyroxene, and olivine) and is rich in divalent cations. Steady-state element release rates from crystalline basalt at far-from-equilibrium conditions were measured at pH from 2 to 11 and temperatures from 5 to 75 C in mixed-flow reactors. Steady-state Si and Ca release rates exhibit a U-shaped variation with pH, where rates decrease with increasing pH at acid condition but increase with increasing pH at alkaline conditions. Silicon release rates from crystalline basalt are comparable to Si release rates from basaltic glass of the same chemical composition at low pH and temperatures ≥25 C but slower at alkaline pH and temperatures ≥50 C. In contrast, Mg and Fe release rates decrease continuously with increasing pH at all temperatures. This behaviour is interpreted to stem from the contrasting dissolution behaviours of the three major minerals comprising the basalt: plagioclase, pyroxene, and olivine. Element

  19. Ion liquids for safer lithium-ion batteries - aluminium corrosion in TFSI- based ILs

    Czech Academy of Sciences Publication Activity Database

    Nádherná, Martina; Dominko, R.; Gabersček, M.; Reiter, Jakub

    Brno: University of technology Brno, 2009, s. 104-108. ISBN 978-80-214-3943-6. [International Conference Advanced Batteries, Accumulators and Fuel Cells /10./. Brno (CZ), 30.08.2009-02.10.2009] R&D Projects: GA MŠk LC523; GA MŠk(CZ) MEB090806; GA AV ČR KJB400320701 Institutional research plan: CEZ:AV0Z40320502 Keywords : accumulators Subject RIV: CG - Electrochemistry

  20. Role of acidic chemistries in steam treatment of aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-01-01

    The effect of acidic chemistry on the accelerated growth of oxide on aluminium alloys Peraluman 706TM and AA6060 under exposure to high temperature steam was investigated. Studied chemistries were based on citrates and phosphates. Results showed that the presence of citrate and phosphate anions...

  1. Aluminium dissolution for spray pulverization with nitric acid

    International Nuclear Information System (INIS)

    A comparative study of the nitric acid dissolution of aluminium, by immersion and spray pulverization has been carried out in laboratory scale. As a result, the optimum operation conditions to control reaction in the plant are fixed. Operation costs are also evaluated. (author)

  2. STRUCTURE OF ECAP ALUMINIUM AFTER DIFFERENT NUMBER OF PASSES

    Directory of Open Access Journals (Sweden)

    Lucia Ilucová

    2011-05-01

    Full Text Available The structure of high purity (99.99% aluminium processed by equal channel angular pressing in the as pressed state after different number of passes was examined using various stereological methods. An extreme inhomogeneity and complicated anisotropy was observed along the body of rod-like specimens.

  3. 1.3. Processing of aluminium production solid wastes

    International Nuclear Information System (INIS)

    The reprocessing of solid wastes of aluminium production, including fluorine regeneration, carbon regeneration, and extraction of valuable components was considered in this chapter. The main methods of fluorine regeneration, including alkaline, acidic, two-stage leaching, hydrochemical, burning, flotation, sintering, vacuum-thermal pyro hydrolysis were considered as well.

  4. Local electrochemical behaviour of 7xxx aluminium alloys

    NARCIS (Netherlands)

    Andreatta, F.

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a neg

  5. Electrochemical Characterisation of Filiform Corrosion on Aluminium Rolled Products

    NARCIS (Netherlands)

    Huisert, M.

    2001-01-01

    When aluminium is protected by an organic coating a special form of corrosion can occur underneath the organic coating; filiform corrosion. This form of corrosion manifests itself as threadlike filaments under the coating, it causes local delamination of the coating and the coating cannot protect th

  6. Establishment of Integrated Information Displays in Aluminium Surfaces Using Nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan Phuklin; Bladt, Henrik Henriksen; Hansen, Hans Nørgaard

    2005-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in Aluminium that can be penetrated by light. This has resulted in a patent describing how to obtain this effect by etching of local areas in a solid material. The idea behind an invisible display in Aluminum co...... ultra-short pulses, selective etching + anodizing, and electrochemical machining....

  7. On the Numerical Determination of Optimal Textures of Aluminium

    OpenAIRE

    Burgholzer, P; Scherzer, O.

    1994-01-01

    In this paper a mathematical algorithm is studied to improve the deep-drawing quality of an aluminium sheet. The deep-drawing quality is usually expressed in terms of the normal anisotropie. In our mathematical model we use Taylor theory and ideal orientations to reformulate this problem as a nonlinear optimization problem for the normal anisotropie. Some numerical examples are presented.

  8. Waste treatment of fission product solutions containing aluminium nitrate

    International Nuclear Information System (INIS)

    In the Rossendorf molybdenum-99 production facility AMOR short-term irradiated aluminium clad fuel elements from the Rossendorf Research Reactor are reprocessed. Following extractive recovery of the enriched uranium the facility system has to be disposed of the fission product-Al(NO3)3 solution. Investigations on waste conditioning of such solutions are presented. (author)

  9. Hydrogen generation from aluminium corrosion in reactor containment spray solutions

    International Nuclear Information System (INIS)

    The aluminium corrosion experiments in reactor containment spray solutions, under the conditions expected to prevail during LOCA in BWR and PWR, were performed in order to investigate relationships between temperature, pH and hydrogen production rates. In order to simulate the conditions in a BWR containment realistic ratios between aluminium surface and water volume and between aluminium surface and oxygen volume were used. Three different aluminium alloys were exposed to spray solutions: AA 1050, AA 5052 and AA 6082. The corrosion rates were measured for BWR solutions (deaerated and aerated) with pH 5 and 9 at 50, 100 and 1500C. The pressure was constantly 0.8 MPa. The hydrogen production rate was measured by means of gas chromatography. In deionized BWR water the corrosion rates did not exceed about 0.05 mm/year in all cases, i.e. were practically independent of temperature and pH. Hydrogen concentrations were less than 0.1 vol.% in cooled dry gas. Corrosion rates and hydrogen production in PWR alkaline solution measured at pH 9.7 and 1500C were very high. AA 5052 alloy was the best material

  10. Microstructure and defect chemistry of yttrium aluminium garnet ceramics

    International Nuclear Information System (INIS)

    This thesis describes basic aspects concerning the defect chemistry and the microstructure of yttrium aluminium garnet ceramics. The work consists of three parts: a literature study, an experimental part and a section giving computer simulation data of defects. (author). 320 refs.; 68 figs.; 72 schemes; 32 tabs

  11. Finite size melting of spherical solid-liquid aluminium interfaces

    DEFF Research Database (Denmark)

    Chang, J.; Johnson, Erik; Sakai, T.; Saka, H.

    2009-01-01

    We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting tempera...... the conclusion that the depressed melting temperature is not controlled solely by the inverse radius 1/R. Instead, we found a direct relation between the depressed melting temperature and the ratio between the solid-liquid interface area and the molten volume.......We have investigated the melting of nano-sized cone shaped aluminium needles coated with amorphous carbon using transmission electron microscopy. The interface between solid and liquid aluminium was found to have spherical topology. For needles with fixed apex angle, the depressed melting...... temperature of this spherical interface, with radius R, was found to scale linearly with the inverse radius 1/R. However, by varying the apex angle of the needles we show that the proportionality constant between the depressed melting temperature and the inverse radius changes significantly. This led us to...

  12. SOLUBILITY OF SILICON IN CAST ALUMINIUM ALLOY AFTER ELECTROHYDROPULSE TREATMENT

    OpenAIRE

    Dyachenko, S.; Fedchenko, N.

    2006-01-01

    The structure of cast aluminium alloy AЛ9 exposed to electrohydropulse treatment (EHPT) was studied. It has been shown that after EHPT solubility of silicon in alloy matrix was increased. With the help of thermodynemic analysis the structural changes in metal after EHPT were explained.

  13. Effect of Low Strain Rate on Formability of Aluminium Alloy

    OpenAIRE

    Bidulská, J.; T. Kvačkaj; Bidulský, R.; Cabbibo, M.; Evangelista, E.

    2007-01-01

    Effect of low strain rate on formability of aluminium alloy 2014 by means of torsion test was performed. The presented experimental results exhibit decrease of the ductility with increase and decrease of ε and T, respectively, and optimal values of , ε T are thus obtained.

  14. Aluminium enriched diffusion layers on NiAl alloy

    Czech Academy of Sciences Publication Activity Database

    Bartuška, Pavel; Lašek, Jiří; Paidar, Václav

    2003-01-01

    Roč. 19, č. 3 (2003), s. 185-188. ISSN 0267-0844 R&D Projects: GA AV ČR IAA1041302 Institutional research plan: CEZ:AV0Z1010914 Keywords : intermetallics based on Ni-Al * aluminium enriched diffusion layers * local elemental analysis Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.571, year: 2003

  15. Anisotropy of tertiary creep in aluminium-based composites

    Czech Academy of Sciences Publication Activity Database

    Dobeš, Ferdinand; Milička, Karel

    Naples : University of Naples, 2005 - (Crivelli-Visconti, I.), s. 225-226 [Advancing with composites 2005. Naples (IT), 11.10.2005-14.10.2005] Institutional research plan: CEZ:AV0Z20410507 Keywords : metal matrix composite * tertiary creep * aluminium alloys Subject RIV: JI - Composite Materials

  16. Aluminium in food and daily dietary intake estimate in Greece.

    Science.gov (United States)

    Bratakos, Sotirios M; Lazou, Andriana E; Bratakos, Michael S; Lazos, Evangelos S

    2012-01-01

    Aluminium content of foods, as well as dietary aluminium intake of the Greek adult population, was determined using graphite furnace atomic absorption spectroscopy after microwave sample digestion and food consumption data. Al content ranged from 0.02 to 741.2 mg kg⁻¹, with spices, high-spice foods, cereal products, vegetables and pulses found to be high in Al. Differences in aluminium content were found between different food classes from Greece and those from some other countries. Aluminium intake of Greeks is 3.7 mg/day based on DAFNE Food Availability Databank, which uses data from the Household Budget Surveys. On the other hand, according to the per capita food consumption data collected by both national and international organisations, Al intake is 6.4 mg day⁻¹. Greek adult population has an Al intake lower than the Provisional Tolerable Weekly Intake of 7 mg kg⁻¹ body weight established by EFSA. Cereals and vegetables are the main Al contributors, providing 72.4% of daily intake. PMID:24779693

  17. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  18. Hydrogen evolution from aluminium in reactor containment spray solutions

    International Nuclear Information System (INIS)

    Three different aluminium alloys were exposed to conditions similar to BWR and PWR containment spray waters at 50, 100 and 1500C. BWR deionized water gives corrosion rates of at most 0.05 mm/year and hydrogen concentrations less than 0.1-1%. On the contrary PWR alkaline solutions give very high corrosion rates and hydrogen contents. (Auth.)

  19. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines

    DEFF Research Database (Denmark)

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E; Bygum, Anette

    2016-01-01

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year...

  20. Effects of Aluminium in Forest. Results of a pilot experiment

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, J.; Wit, H. de; Nygaard, P.H.

    1996-01-01

    This conference paper deals with an Norwegian pilot project which started in 1995 and finishing early 1999, investigates the solubility and phyto-toxicity of aluminium (Al) in mature forest ecosystems. The project consists of three major parts, including field manipulation study of Norwegian spruce stands, laboratory experiments and modelling Al chemistry in the root zone. 15 refs.

  1. Corrosion of research reactor aluminium clad spent fuel in water

    International Nuclear Information System (INIS)

    A large variety of research reactor spent fuel with different fuel meats, different geometries and different enrichments in 235U are presently stored underwater in basins located around the world. More than 90% of these fuels are clad in aluminium or aluminium based alloys that are notoriously susceptible to corrosion in water of less than optimum quality. Some fuel is stored in the reactor pools themselves, some in auxiliary pools (or basins) close to the reactor and some stored at away-from-reactor pools. Since the early 1990s, when corrosion induced degradation of the fuel cladding was observed in many of the pools, corrosion of research reactor aluminium clad spent nuclear fuel stored in light water filled basins has become a major concern, and programmes were implemented at the sites to improve fuel storage conditions. The IAEA has since then established a number of programmatic activities to address corrosion of research reactor aluminium clad spent nuclear fuel in water. Of special relevance was the Coordinated Research Project (CRP) on Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase I) initiated in 1996, whose results were published in IAEA Technical Reports Series No. 418. At the end of this CRP it was considered necessary that a continuation of the CRP should concentrate on fuel storage basins that had demonstrated significant corrosion problems and would therefore provide additional insight into the fundamentals of localized corrosion of aluminium. As a consequence, the IAEA started a new CRP entitled Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase II), to carry out more comprehensive research in some specific areas of corrosion of aluminium clad spent nuclear fuel in water. In addition to this CRP, one of the activities under IAEA's Technical Cooperation Regional Project for Latin America Management of Spent Fuel from Research Reactors (2001-2006) was corrosion monitoring and surveillance of research

  2. Mechanically milled aluminium matrix composites reinforced with halloysite nanotubes

    Directory of Open Access Journals (Sweden)

    L.A. Dobrzański

    2012-12-01

    Full Text Available Purpose: The present work describes fabrication of aluminium AlMg1SiCu matrix composite materials reinforced with halloysite nanotubes by powder metallurgy techniques and hot extrusion.Design/methodology/approach: Mechanical milling, compacting and hot extrusion successively are considering as a method for manufacturing metal composite powders with a controlled fine microstructure and enhanced mechanical properties. It is possible by the repeated welding and fracturing of powders particles mixture in a highly energetic ball mill.Findings: The milling process has a huge influence on the properties of powder materials, changing the spherical morphology of as-received powder during milling process to flattened one due to particle deformation followed by welding and fracturing particles of deformed and hardened enough which allows to receive equiaxial particles morphology again. The investigation shows that so called brittle mineral particles yields to plastic deformation as good as ductile aluminium alloy particles. That indicates that the halloysite powder can play a role of the accelerator during mechanical milling. High energy ball milling as a method of mechanical milling improves the distribution of the halloysite reinforcing particles throughout the aluminium matrix, simultaneously reducing the size of particles. The apparent density changes versus milling time can be used to control the composite powders production by mechanical milling and the presence of halloysite reinforcements particles accelerates the mechanical milling process.Research limitations/implications: Contributes to knowledge about technology, structure and properties of aluminium alloy matrix composite material reinforced with mineral nanoparticles.Practical implications: Conducted research shows that applied technology allows obtaining very good microstructural characteristics.Originality/value: It has been confirmed that halloysite nanotubes can be applied as an effective

  3. Metallurgical Characterisation of Recovered Aluminium Alloys in Cameroon

    Directory of Open Access Journals (Sweden)

    T. Tchotang

    2013-07-01

    Full Text Available This article is a comparative study of metallurgical characteristics of the different aluminium alloys gotten through recycling of recovered aluminium in Cameroon. A simple experimental device for the foundry of secondary aluminium blend, of very good quality built around a movable charcoal furnace is presented. It enables better energy efficiency, a better distribution of the heat around the crucible and indirectly assures good quality of the products obtained, while respecting the economic constraints and users' safety. Six refining methods are proposed by the addition of polyvinyl chloride (method A, coke rich in carbon CHS (method C, ammonium chloride NH4Cl (method E, manganese dioxide MnO (method T, acrylic nitrite (C2H3Cln (method P and sodium chloride NaCl (method S. A critical analysis of the different recycling techniques is presented as well as a proposed process of melting and refining that enables the obtaining products with high degrees of purity. The results are then compared to the results obtained from the industrial methods of aluminium refining such as fractional crystallization (FC, granular filtration (GF and dissolution in a metal solvent (DS. The later (DS gives the rate of 6.540% of accumulated alloy elements and enables the best purification (93.460%, while the NaCl gives the lowest global rate of additive elements (9.478%, with the best purity index (90.522% amount the proposed methods. Results obtained show that this method of refining improves the metallurgical properties of secondary aluminium alloy blends and guarantees better safety, as well as reducing the risks of environmental pollution.

  4. Microprobe PIXE analysis of aluminium in the brains of patients with Alzheimer's disease

    Science.gov (United States)

    Yumoto, S.; Horino, Y.; Mokuno, Y.; Kakimi, S.; Fujii, K.

    1996-04-01

    To investigate the cause of Alzheimer's disease (senile dementia), we examined aluminium (Al) in the rat liver, and in the brains (hippocampus) of Alzheimer's disease patients using heavy ion (5 MeV Si 3+) microprobe and proton (2 MeV) microprobe PIXE analysis. Heavy ion microprobes (3 MeV Si 2+) have several time's higher sensitivity for Al detection than 2 MeV proton microprobes. (1) In the rat liver, Al was detected in the cell nuclei, where phosphorus (P) was most densely distributed. (2) We also demonstrated Al in the cell nuclei isolated from Alzheimer's disease brains using heavy ion (5 MeV Si 3+) microprobes. Al spectra were detected using 2 MeV proton microprobes in the isolated brain cell nuclei. Al could not be observed in areas where P was present in relatively small amounts, or was absent. Our results indicate that Alzheimer's disease is caused by irreversible accumulation of Al in the nuclei of brain cells.

  5. Canada: a big investment for the aluminium valorization; Canada: un gros investissement pour la valorisation de l'aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2005-02-01

    An amount of more than 2.4 millions of dollars has been given by the Quebec at the research and development sector for the aluminium valorization. Six plans will be studied by more than 30 searchers and 20 students in technology. (O.M.)

  6. Design of the lines of aluminium drawing. Part 1; Conception des filieres de filage d'aluminium. Partie 1

    Energy Technology Data Exchange (ETDEWEB)

    Cescutti, J.P.; Ravaille, N. [Pechiney, Div. Filiage, 75 - Paris (France)

    2005-12-15

    After a general presentation, the second paragraph gives the main reasons of the complexity of the problem to be solved. Coming from the 'sciences of design', these aspects give valuable data to structure the analysis of the progress ways in the field of the design of the lines of aluminium extrusion. (O.M.)

  7. Some regularities of ion exchange processes in production of zeolite-containing catalysts of cracking

    International Nuclear Information System (INIS)

    The equilibrium of lanthanum- and ammonium ion exchange on Y-type zeolite and amorphous aluminium silicate has been studied, the ions being constituents of a cracking catalyst. Nomograms, permitting to make calculations of cation compositions of each ion-exchanger depending on the composition and total concentration of a solution, are plotted. On the basis of the nomograms the optimum values of the cation composition and concentration of a solution are found, which ensure preparation of a catalyst with a high degree of lanthanum substitution for ammonium in zeolite at a relatively low degree of ammonium penetration into amorphous aluminium silicate are found

  8. Steel sheet composite materials with foamed aluminium; Stahlblechverbundwerkstoffe mit geschaeumtem Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Baumeister, J.; Weber, M. [Institut fuer Angewandte Materialforschung, Bremen (Germany); Bleck, W.; Hagen, H. von [Technische Hochschule Aachen (Germany). Lehrstuhl und Inst. fuer Eisenhuettenkunde

    1999-07-01

    Sandwich structured steel sheets with a core of foamed aluminium can be produced by roll-bonding and glueing. Results of corrosion tests and laser welding tests so far were positive. Several applications have been proposed but none of them has been implemented as yet. The material is recommended for applications with a profile of requirements comprising structurally and functionally relevant characteristics. Recycling is unproblematic. [German] Zur Herstellung von Stahlblechsandwichverbunden mit einem Aluminiumschaumkern lassen sich die Verfahren Walzplattieren und Kleben einsetzen. Es sind Sandwichverbunde mit Gesamtdichten von 0,7 bis 2,0 g/cm{sup 3} und Gesamtdicken zwischen 10 und 32 mm darstellbar. Die Tafelgroessen fuer die vielversprechendsten Verfahren liegen derzeit bei ueber DIN A3 (konventionell geschaeumt) oder 160 mm x mehrere m (kontinuierlich im Banddurchlaufofen geschaeumt) und 2 m x 600 mm (geklebt). Es lassen sich gute mechanische Eigenschaften des Sandwichverbundes (Biegesteifigkeit) und hohe Versagensreserven bei Druck- und Biegebeanspruchungen sowie interessante funktionelle Eigenschaften (z.B. hohe Energieaufnahme) erzielen. Aus Tastversuchen zu Korrosionseigenschaften und Fuegeverfahren (Laserschweissen) konnten positive Resultate gewonnen werden. Vorschlaege zu Anwendungen bestehen, aber ein direkter Einsatz ist noch nicht realisiert worden. Ein Einsatz des Werkstoffverbundes ist sinnvoll in Gebieten, in denen ein Anforderungsprofil von strukturell und funktionell relevanten Eigenschaften vorherrscht. Das Recycling der rein metallischen Verbunde ist problemlos. (orig.)

  9. Aluminium content of foods originating from aluminium-containing food additives.

    Science.gov (United States)

    Ogimoto, Mami; Suzuki, Kumi; Haneishi, Nahoko; Kikuchi, Yuu; Takanashi, Mayu; Tomioka, Naoko; Uematsu, Yoko; Monma, Kimio

    2016-09-01

    Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples. PMID:27092423

  10. ThermophysicalProperties of Cellular Aluminium andCeramic Particulate / Aluminium Composites

    Directory of Open Access Journals (Sweden)

    Khalid Almadhoni

    2015-10-01

    Full Text Available In this paper, the thermophysical properties of cellular Al and Ceramic Particulate / Al Composites were explored. Thermophysical properties are defined as material properties that vary with temperature without altering the material's chemical identity including thermal conductivity (TC, coefficient of thermal expansion (CTE, energy absorption, porosity and relative density. The significance of cellular Al and AMMCs reinforced by ceramic particles lies in their propertieswhich are difficult to be available combined in other engineering materials. New cellular AMMCs that meet the needs of the required engineering applications could be synthesized by selection an appropriate reinforcements. Different kinds of ceramic particles such as oxides, carbides, nitrides, as well as carbon nanotubes can be utilized as reinforcements for manufacturing of cellular AMMCs. Thermophysicalproperties of cellular AMMCs consisting of Al as continuous matrix phase and ceramic particles as reinforcements are directly influenced by type, size, and geometry of dispersions, also the RVR. In addition, the constituents of ceramic particulate / aluminium composites characterized by different heat transfer mechanisms, wherethe TC mechanism in metals is attributed to free electrons, while phonons are primarily responsible for TC in nonmetallic materials, as well as an interfacial thermal barrier resistance influence effectively on heat transfer inside the composite and thus the thermophysical properties. In this paper, based on the literature review, thermophysical properties of cellular Al and AMMCs reinforced by ceramic particles were discussed.

  11. Numerical and experimental investigations of aluminium powder compaction; Numerische und experimentelle Untersuchungen zum Pulverpressen von Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Hanini, K.; Doege, E.; Schmidt-Juergensen, R. [Institut fuer Umformtechnik und Umformmaschinen, (IFUM) Universitaet Hannover, Welfengarten 1A, 30167 Hannover (Germany)

    2003-08-01

    The FEM simulation is a powerful means which can drastically reduce the time to production and costs in the optimization of powder forming processes. The current paper investigates experimentally and numerically die compaction of aluminium powder. The plastic deformation is formulated by using the Drucker-Prager-Cap-model. This yield criterion describes the compressibility of porous bodies and allows the prediction of crack formation in the green compact. Axial compaction tests have been performed to determine material parameters for hardening. Simulation examples are presented to demonstrate the ability of the model to compute the distribution of the relative density. Furthermore, the compaction of an axisymmetric workpiece was simulated in order to determine optimal tools kinematics and to avoid crack formation. (Abstract Copyright [2003], Wiley Periodicals, Inc.) [German] Die Auslegung und Optimierung pulvertechnologischer Umformverfahren basiert bisher zu einem grossen Teil auf Erfahrungswissen. Die numerische Simulation bietet hierbei eine kosten- und zeitsparende Alternative. Besonders hat sich die Finite-Elemente-Methode (FEM) als leistungsfaehiges Simulationsverfahren bewaehrt. Im Rahmen dieser Arbeit wird das Pulverpressen von Aluminiumpulver numerisch und experimentell untersucht. Hierbei wird das Drucker-Prager-Cap-Modell verwendet, um das kompressible Verhalten des Pulvers abzubilden und moegliche Rissbildungen waehrend des Pressvorgangs vorherzusagen. Durch Pressversuche werden die Materialkennwerte fuer dieses Modell hinsichtlich der Verdichtung und Verfestigung des Aluminiumpulvers ermittelt. Der Pressvorgang wird anhand ausgewaehlter Referenzbauteile simuliert. Von besonderem Interesse ist hierbei die Berechnung der Verteilung der relativen Dichte und die Vermeidung der Rissbildung durch Optimierung der Stempelkinematik. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

  12. Influence of solution concentration of aluminium, arsenic, boron and copper on root growth in relation to the phytotoxicity of pulverized fuel ash

    Energy Technology Data Exchange (ETDEWEB)

    Collier, G.F.; Greenwood, D.J.

    1977-01-01

    To find whether the concentrations of aluminium, arsenic, boron or copper and soluble sulfate salts which have previously been found in the aqueous phase of water saturated pulverized fuel ash (PFA) are sufficiently high to restrict growth, lettuce seedlings were grown on filter paper saturated with a solution containing various concentrations of each of the different ions. Over a period of five days root growth was reduced by half when the concentration of aluminium was increased to 2.0 mg/liter, arsenic (As/sup 3 +/) to 1.6 mg/liter, boron to 90 mg/liter or copper to 0.3 mg/liter or when the soluble sulfate salts were increased to 100 mEq/liter (conductivity 8 x 10/sup -3/ ohm/sup -1/ cm/sup -1/ at 20/sup 0/C). The concentrations of ions in the aqueous phase of wet PFA depend on pH which varies greatly from one batch of ash to another. The concentrations of aluminium and copper in equilibrium with acid batches of ash and those of arsenic in equilibrium with alkaline batches of ash were sufficiently high to restrict growth. The concentration of boron and soluble salts were always at phytotoxic levels irrespective of the pH of the ash. 15 references, 6 figures, 4 tables.

  13. Effects of Nano-Aluminium on The Combustion of A PolyNIMMO-Based Propellant

    Institute of Scientific and Technical Information of China (English)

    Clive Woodley; Peter Henning

    2014-01-01

    Propellants containing micro-aluminium particles have been shown to produce faster burn rates than conventional gun propellants.However,they are also more abrasive than conventional propellants.Nano-material propellants have been reported to give similar benefits to micron-material propellants but without the disadvantage of increased abrasion.Tests were conducted to compare the burn rates,ignitability and wear rates of a propellant loaded with 0% aluminium,15% micro-aluminium and 15%nano-aluminium.Closed vessel tests showed a burn rate increase of 39% in the range 30-250 MPa,and 70% at low pressure (50-100 MPa)for the nano-aluminium propellant compared with the baseline propellant.The micro-aluminium propellant showed only a 10% increase in the burn rate compared with the standard propellant.The ignition delay for the nano-aluminium propellant was slightly shorter than that of the baseline propellant.Substantially increased wear rates were measured for the micro-aluminium propellant.The nano-aluminium propellant showed reduced wear rates compared with the micro-aluminium propellant but these were still substantially greater than those for the baseline propellant.

  14. Fast ignition by quasimonoenergetic ion beams

    Directory of Open Access Journals (Sweden)

    Honrubia J.J.

    2013-11-01

    Full Text Available The potential of quasimonoenergetic ion beams for fast ignition (FI of fusion targets is investigated. Lithium, carbon, aluminium and vanadium ions have been considered here to determine the optimal kinetic energy for each ion type. Our calculations show that the ignition energies of those beams impinging on a standard fuel configuration are similar. However, they are obtained for very different ion energies. Assuming that the ions can be focused onto 10 μm spots, a new irradiation scheme that reduces substantially the ignition energies is proposed. The combination of using intermediate ions, such as 5.5 GeV vanadium, and the new irradiation scheme allows one to reduce the number of ions required for ignition by roughly three orders of magnitude when compared with the standard proton FI scheme.

  15. Active metal brazing of different metals to aluminium nitride ceramics

    International Nuclear Information System (INIS)

    During recent years aluminium nitride ceramics for substrates, coolers and components have found more applications in micro- and power electronics. Aluminium nitride ceramic with high thermal conductivity, small CTE and good thermal shock resistance is used in aeronautical equipment as well as in drive systems of undergrounds and high speed trains. Different metals and alloys can be bonded to AIN by the so-called 'AMB-process'. The bonding mechanism is based on the use of so-called active metals like Ti, Zr, Hf. Copper conductor lines can be brazed onto AIN-substrates and components, resistor sheets can be applied on ceramic water coolers and a couple of other metals and alloys like tantalium, titanium, KOVAR and steel can be attached to AIN-ceramics by active brazing. Processing, analytical aspects and some special applications will be discussed. (author)

  16. Nano α-alumina powders from aluminium dross waste

    International Nuclear Information System (INIS)

    The paper describes a solvo thermal chemical process to recycle aluminium dross waste into nano α-alumina powder. The process includes washing to remove the unwanted sodium follow by dissolving of this waste with dilute acid. The solvo thermal process then proceed with addition of propanol to crystallize the aluminium hydroxide. XRD analysis of this crystal shows that it belongs to Gibbs site (Al(OH)3). The crystals were then calcined at 1300 degree C where white powder was produced. Characteristic studies were then performed on this powder using XRD, SEM, EDX and particle size analysis showing that it has single α-alumina crystal phase with almost spherical shape. As the initial particle size is coarse and had a mean particle size of 3.80 μm, high speed wet milling was used and enable to reduce it to 0.49 μm. (Author)

  17. Effect of pressurized steam on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

    2012-01-01

    measurements were used to study corrosion behavior. Findings - A 590?nm boehmite oxide layer was generated on AA1050 associated with partially dissolved and/or fallen off Fe-containing intermetallic particles after exposure to pressurized steam. A significant reduction (25 times) in anodic and cathodic......Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed to...... pressurized steam produced from a commercial pressure cooker at the maximum temperature of 116oC for 10?min. Surface morphology was observed using SEM-EDX and FIB-SEM. Phase identification and compositional depth profiling were investigated using XRD and GDOES, respectively. Potentiodynamic polarization...

  18. Production of aluminium oxide from the kaolin waste reprocessing

    International Nuclear Information System (INIS)

    The kaolin processing for paper covering produces a great volume of residues formed primary by clay mineral kaolinite which was in this study, the starting point for the synthesis of ammonium alum aiming to obtain free sodium alumina with fine grade for ceramic manufacture. The synthesis process to obtain ammonium alum consisted of the following procedures: residues calcination and sulphuric leaching of meta kaolinite followed by neutralization/ crystallization of aluminium sulphate solution with ammonium hydroxide concentrated solution. The effect of calcination temperature (650 deg C, 700 deg C and 750 deg C), calcination time of residues (30 min, 60 min and 120 min),sulphuric acid concentration as well as leaching temperature (70 deg C, 80 deg C and 90 deg C) on kinetics of aluminium leaching were studied. The influence of pH on ammonium alum crystallization was also studied. Data on chemical analysis, XRD and DTA of raw material utilized and synthesized are presented and discussed. (author)

  19. The nature of point defects in plastically deformed aluminium

    International Nuclear Information System (INIS)

    In order to find out which types of point defect are produced by plastic deformation, 57Co-doped aluminium specimens were cold worked at various temperatures by unidirectional tensile deformation or cyclic torsion. The specimens were then annealed at increasing temperatures, and the trapping of defects at the 57Co probes was studied by Moessbauer spectroscopy. In none of the experiments were interstitials found, although it is known that in aluminium 57Co probes readily trap interstitials after low-temperature particle irradiation. However, vacancy trapping was found in two temperature ranges corresponding to two different migration energies of vacancies: in dislocations Esub(m)sup(d) approx.0.2 to 0.3 eV and in the lattice Esub(m) approx.= 0.6 eV. The consequences of the results on models of point defect production by cold working are discussed. (author)

  20. Impact of Inert Metal Particles Flow on Aluminium Plate

    Institute of Scientific and Technical Information of China (English)

    WANG Zhongqi; LIU Yi; CHEN Yahong; BAI Chunhua

    2008-01-01

    Inert metal explosive, a new kind of explosive, is a mixture of high explosive and inert metal particle.When this kind of explosive is detonated, an inert metal particle flow will be formed by the explosive product driving.To determine the characteristics of the movement of the metal particle flow, a series of aluminium plates were designed to be the targets on which the metal particle flow impacted.The test result was presented and a numerical model was set up to analyze the impact of the high speed inert metal particles on aluminium plate.Based on the numerical analysis, the relationship between the characteristic of the mark on the target plate and the initial condition of the inert metal particles was proposed.From the analysis of the impact on target plates, more information about the movement of the metal particles could be reconstructed.

  1. Mechanisms of de cohesion in cutting aluminium matrix composites

    International Nuclear Information System (INIS)

    In this paper properties and applications of aluminium matrix composites are presented with a composite reinforced with saffil fibres selected for topical study. Behavior of matrix and reinforcement during machining with a cutting tool is analyzed. The paper presents an explosive quick-stop device designed to obtain undisturbed machined surface for examination. Meso hardness measurements of deformed structure, resultant chips and built-up-edge were carried out. Scanning micrographs of machined surface are presented with morphology and types of chips analysed. Values of the fibrousness angle ψ and thickening index kh of chip are evaluated. The research performed has enabled the authors to define mechanisms of e cohesion during cutting aluminium matrix composites. The results received for composite material are compared with those pertinent to aluminum alloys.

  2. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    K T Kashyap; T Chandrashekar

    2001-08-01

    Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the scientific literature. The nucleant effects i.e. which particle and its characteristics nucleate -Al, has been the subject of intensive research. Lately the solute effect i.e. the effect of dissolved titanium on grain refinement, has come into forefront of grain refinement research. The present paper attempts to review the literature on the nucleant effects and solute effects on grain refinement and addresses the importance of dissolved titanium in promoting nucleation of -Al on nucleant particles.

  3. Structural colours and applications to anodised aluminium surfaces

    DEFF Research Database (Denmark)

    Johansen, Villads Egede

    solve the problem. The problem is investigated by first reviewing existing work within colouration and visual appearance. This includes a study on how colours are perceived by humans and an investigation of the characteristics with which a surface appearance is properly described. Subsequently......, nanostructures and surface profiles are investigated using optimisation and topology optimisation in order to understand the limitations and design freedom of colour engineering. This is then followed by a study of the effect of disorder on a nanoscale level in order to tailor surface reflections for a smooth......, pleasing appearance. Afterwards, optical models for scattering of non-deterministic geometries suitable for anodised aluminium are considered. The outcome of the investigations are several different proposals for obtaining a white appearance for aluminium. These are described in the thesis alongside a...

  4. Microstructure evolution and grain refinement in asymmetrically rolled aluminium

    International Nuclear Information System (INIS)

    Aluminium alloy sheets were asymmetrically rolled and annealed. Asymmetric rolling was applied by imposing different velocity ratios between the top and bottom rolls, from 1 to 1.5. After cold rolling, the microstructures of various samples were analysed by electron back scatter diffraction, whereas the mechanical properties were characterized by stress–strain curves and microhardness measurements. The asymmetrical rolling process was examined as an alternative method to obtain fine- or even ultrafine-grained aluminium. The main purpose of this paper is to describe, qualitatively and quantitatively, the influence of asymmetrical rolling on microstructure evolution. Grain size, misorientation, image quality factor and other parameters were characterized and analysed in some detail. In the present study, a unique approach has been used for the first time to examine the possibility of applying the asymmetric rolling process in the preparation of materials with controlled heterogeneity

  5. TORSIONAL DEFORMATION AND FATIGUE BEHAVIOUR OF 6061 ALUMINIUM ALLOY

    Directory of Open Access Journals (Sweden)

    marini marno

    2012-02-01

    Full Text Available Torsional deformation and fatigue behaviour of both solid and thin-walled tubular specimens were made from as-received and heat treated 6061 aluminium alloy were studied. 6061 aluminium alloy have been widely used as a candidate material in automobile, aerospace, aircraft and structural application because of their superior mechanical properties such as high strength to weight ratio, good ductility and others. The differences in cyclic deformation and fatigue behaviours between round and solid specimens where a stress gradient exist, and thin-walled tubular specimens where a uniform stress state is commonly assumed, are also discussed. Von Mises and Tresca criteria has been used to predict the monotonic and cyclic deformation curve and compared to the torsional data obtained from the experiment. The S-N curve was used to present and evaluate the fatigue life of the specimens. Through fractographic analysis, failure criteria of fracture surfaces were observed and discussed. 

  6. Experimental evidence for a dynamical crossover in liquid aluminium.

    Science.gov (United States)

    Demmel, F; Fraile, A; Szubrin, D; Pilgrim, W-C; Morkel, C

    2015-11-18

    The temperature dependence of the dynamic structure factor at next-neighbour distances has been investigated for liquid aluminium. This correlation function is a sensitive parameter for changes in the local environment and its Fourier transform was measured in a coherent inelastic neutron scattering experiment. The zero frequency amplitude decreases in a nonlinear way and indicates a change in dynamics around 1.4 ∙ Tmelting. From that amplitude a generalized viscosity can be derived which is a measure of local stress correlations on next-neighbour distances. The derived generalized longitudinal viscosity shows a changing slope at the same temperature range. At this temperature the freezing out of degrees of freedom for structural relaxation upon cooling sets in which can be understood as a precursor towards the solid state. That crossover in dynamics of liquid aluminium shows the same signatures as previously observed in liquid rubidium and lead, indicating an universal character. PMID:26465204

  7. Environment pollution with aluminium around a coalburning electric power plant

    International Nuclear Information System (INIS)

    The experiments were carried out from November 1991 till November 1993 on the area surrounding an electric power plant within the circle of 20 km diameter and five geographical directions (N, S, SE, E, W). The results presented in this paper have indicated the threats caused by emissions of the power plant ashes and dusts. Mean aluminium content in soil has been multiply surpassed on the area studied. This must have as impact on fauna and flora. The distribution and intensity of pollution is determined first of all by the distance from the emitters and direction of prevailing winds. A part of aluminium contained in water soluble compounds can be distributed on large areas, what adds a lot to the threat to animals. That is why high chimneys do not solve the problem of pollution around big industrial plants. (author)

  8. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    DEFF Research Database (Denmark)

    Aggerbeck, Martin

    The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions of this...... the previously described magnetron sputtered Al-Ti coatings showed that 13 wt. % titanium and more improved the corrosion resistance at pH 13.5 and this was further improved by heat treatment, especially at 400 °C and more. The improved corrosion properties were ascribed to structural relaxation......, decreased galvanic potential differences in the microstructure, and protection from the network of the Al3Ti phases precipitated during the heat treatment. Laser surface cladding of aluminium containing up to 20 wt. % Ti6Al4V were studied focusing on the microstructure and the alkaline corrosion properties...

  9. Radiative capture of polarized neutrons by aluminium and manganese nuclei

    International Nuclear Information System (INIS)

    The angular distribution of the intensity is calculated for primary and secondary gamma-rays emitted after polarized neutron capture in a polarized target. Also the circular polarization is derived for capture of polarized neutrons by unoriented nuclei. Interference between the reaction channels and all possible dipole/quadrupole mixing is taken into account. Some aspects of p-wave and s-p interference are discussed. The results of these calculations are applied to the experiments on aluminium and manganese. In the nuclear orientation experiment with aluminium a 'brute force' polarized target was used. For five levels in 28Al the spin value could be determined uniquely. No evidence for significant M2/E1 mixing is found. A ferromagnetic MnSb sample was used to polarize the manganese nuclei. Unique spin values are assigned to 13 states in 56Mn. The magnetic hyperfine field on the Mn nuclei is determined to be negative

  10. Hole mobility in aluminium implanted silicon

    Science.gov (United States)

    Galvagno, G.; La Ferla, A.; La Via, F.; Raineri, V.; Gasparotto, A.; Carnera, A.; Rimini, E.

    1997-11-01

    The dependence of the hole mobility on the dopant concentration ranging from 0268-1242/12/11/018/img8 to 0268-1242/12/11/018/img9 was determined at room temperature in Al-implanted Si samples. The trend was obtained by the use of Hall effect and resistivity measurements on the van der Pauw pattern in combination with secondary-ion mass spectrometry and spreading resistance analysis. The mobility data are in a quite good agreement with the Wagner curve for boron in the high Al concentration region while they approach the Thurber boron curves at low concentrations. This result indicates that the neutral and ionized impurity scattering mechanisms are not critically different for Al- and B-doped samples. The mobility - dopant concentration curve can be employed to convert the resistivity profiles obtained by spreading resistance measurements into hole concentration distributions for Al-doped samples.

  11. Melting defect characterization in aluminium alloys by using computerized tomography

    International Nuclear Information System (INIS)

    This paper analyses the performance of parallel beam X-ray transmission computerized tomography, in the characterization of melting defects on a aluminium alloy. The results obtained presented a spatial resolution approximately of 0.8 mm. The porosity distribution existent in the piece appears as noise at the tomographic images with impossible detection. From the tomograms analyses it was possible to classify two defect regions at the pieces: empty and large pore concentration

  12. Studies on the chelation of aluminium for biological application

    International Nuclear Information System (INIS)

    Potentiometric determinations of the strength of chelation of aluminium(III) by citrate and 3-carboxy-1,5-pentanedioic acid have been made at 37,0 plus minus 0,1 degree Celsius and I = 150 mmol dm-3 NaCl. From these results, the citrate complex is inferred to be tridentate with coordination through the two terminal carboxyl groups and the central hydroxyl group. This structure is confirmed by 13C nuclear magnetic resonance

  13. Characteristics of particulate emissions from aluminium electrolysis cells

    OpenAIRE

    Gaertner, Heiko

    2013-01-01

    Modern sampling and analysis techniques were applied to study the morphology and composition of pot exhaust particles from aluminium smelters. In this study the total spectrum of pot exhaust particles from prebake electrolysis cells was sampled on filters and in a standard cyclone. Application of a cascade impactor allowed for fractionation of raw gas dust into 12 fractions with particle diameters in the range from approximately 7 nm to 10 μm. The performed experiments demonstrated that the p...

  14. Experimental study of friction in aluminium bolted joints

    OpenAIRE

    Vincenzi N.; De Agostinis M.; Croccolo D.

    2010-01-01

    This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately desig...

  15. ICT measuring method of small gap in aluminium component

    International Nuclear Information System (INIS)

    Because of the limitation of image reconstruction theory, the spatial resolution and random dispersion of CT value determine the minimum measuring size of Industrial Computed Tomography (ICT). This paper put forward the local boundary integration conception and found a new method to precisely measure the gap between 0.01-0.15 mm in aluminium component. When the credibility is 95%, the measuring accuracy is better than ± 0.005 mm. (authors)

  16. Load carrying capacity analysis of materials for aluminium rims

    OpenAIRE

    Fajdiga, Matija; Čižman, Jure

    2015-01-01

    In this contribution we present an experimental simulation of the fatique strength of clamped aluminium rims. This is supported by numerical modelling using the Finite Element Method (FEM), which was used for stress-strain analysis of a model representing a clamped detail during bendings. The design and analysis of the model are made simultaneously on an integrated computer controlled test rig for testing the fatique strength of clamped parts subjected to bending. The simulation is evaluated ...

  17. Fatigue Strength of Friction Stir Welded Joints in Aluminium

    OpenAIRE

    Ericsson, Mats

    2005-01-01

    Solid state Friction stir welding (FSW) is of major interest in the welding of aluminium since it improves the joint properties. Many applications where Al-alloys are used are subject to varying load conditions, making fatigue failure a critical issue. In the scope of this thesis, the fatigue performance of friction stir welded AlMgSi-alloy 6082 has been investigated. Static and dynamic properties of different joint configurations and welds produced with varying process parameters have been d...

  18. Fabrication and characterisation of uranium, molybdenum, chromium, niobium and aluminium

    International Nuclear Information System (INIS)

    This paper describes fabrication of binary uranium alloys by melting and casting. The following alloys with nominal composition were obtained by melting in the vacuum furnace: uranium with niobium contents from 0.5%- 4.0% and uranium with molybdenum contents from 0.4% - 1.2%. Uranium alloys with chromium content from 0.4% - 1.2% and uranium alloy with 0.12% of aluminium were obtained by vacuum induction furnace (electric arc melting)

  19. Establishment of integrated information displays in aluminium surfaces using nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan; Hansen, Hans Nørgaard; Bladt, Henrik H.;

    2006-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in aluminium that can be penetrated by light. This work has resulted in a patent describing how to obtain this effect by material removal in local areas in a solid material. The idea behind an invisible display ...... micromachining with ultra-short pulses, selective etching combined with anodizing, and electrochemical machining....

  20. Experimental study of aluminium honeycomb behaviour under dynamic multiaxial loading

    OpenAIRE

    Markiewicz E.; Haugou G.; Chaari F.; Zouari B.; Tounsi R.; Dammak F.

    2012-01-01

    Split Hopkinson Pressure Bar system (SHPB) with large-diameter and Nylon bars introducing a shear-compression loading device is used in order to investigate the dynamic behaviour of aluminium honeycomb under multiaxial loadings conditions. All shear-compression configurations including the loading angle variation from 0∘ to 60∘ are performed with an impact velocity of about 15m/s. The adapted SHPB system with the device are validated numerically and a phenomenon of separation between the inpu...

  1. TEM microstructure investigations of aluminium alloys used as coating substrate

    Directory of Open Access Journals (Sweden)

    T. Tański

    2013-01-01

    Full Text Available Purpose: The aim of this paper was investigated structure and properties of gradient coatings produced in PVD process on AlSi9Cu aluminium alloys.Design/methodology/approach: The following results concern the structures of the substrates and coatings with the application of electron transmission and scanning microscopy; phase composition of the coatings using X-ray diffraction and grazing incident X-ray diffraction technique (GIXRD; microhardness and wear resistance.Findings: The deposited coatings are characterized by a single, double, or multi-layer structure according to the applied layers system, and the individual layers are coated even and tightly adhere to the substrate as well to each other. The analysis of coatings obtained on the surface of cast aluminium alloys by the PVD processes show a clear - over 100% - increase of the microhardness, compared to the base material microhardness.Practical implications: Achieving of new operational and functional characteristics and properties of commonly used materials, including the Al-Si-Cu alloys is often obtained by heat treatment, ie, precipitation hardening and/or surface treatment due to application or manufacturing of machined surface layer coatings of materials in a given group of materials used for different surface engineering processes.Originality/value: The paper presents the research involving the PVD coatings obtained on an unconventional substrate such as aluminium alloys. Contemporary materials should possess high mechanical properties, physical and chemical, as well as technological ones, to ensure long and reliable use. The above mentioned requirements and expectations regarding the contemporary materials are met by the non-ferrous metals alloys used nowadays, including the aluminium alloys.

  2. Work Hardening and Mechanical Anisotropy of Aluminium Sheets and Profiles

    OpenAIRE

    Ryen, Øyvind

    2003-01-01

    The processing of aluminium alloys from casting to end product is associated with a large number of metallurgical phenomena. In order to further improve and optimise process routes and alloys, a thorough understanding of the thermomechanical treatments by experimental observations and physically based modelling is necessary.In part A of this thesis the work hardening behaviour of non-heat treatable alloys is followed up to large strains. The evolution in strength, microstructure and texture d...

  3. Numerical modeling of aluminium foam on two scales

    Czech Academy of Sciences Publication Activity Database

    Němeček, J.; Denk, F.; Zlámal, Petr

    2015-01-01

    Roč. 267, September (2015), s. 506-516. ISSN 0096-3003 R&D Projects: GA ČR(CZ) GAP105/12/0824 Institutional support: RVO:68378297 Keywords : closed-cell aluminium foam * Alporas * multiscale modeling * homogenization * FFT * finite element modeling Subject RIV: JI - Composite Materials Impact factor: 1.551, year: 2014 http://www.sciencedirect.com/science/article/pii/S0096300315001162

  4. Aluminium extrusion investigated by theory, experiment and FEM-analysis

    OpenAIRE

    Khorasani, Sepinood Torabzadeh

    2015-01-01

    The process of aluminium extrusion has important influence in metal forming industry because of its ability to produce profiles with different shapes, sizes and complicated geometries. The required extrusion load is depending on the process parameters such as the flow stress of the billet material, velocity field, strain rate distribution, and thermal conditions within extrusion. These conditions are so important for industries, and interesting for academia, that research has been...

  5. Texture development during recrystallization of aluminium containing large particles

    DEFF Research Database (Denmark)

    Juul Jensen, Dorte; Hansen, Niels; Humphreys, F. J.

    1985-01-01

    The recrystallization process in heavily deformed commercially pure aluminium containing large intermetallic particles was studied by in situ neutron diffraction texture measurements and various microscopical techniques including texture measurements in local areas and simultaneous determination of...... size and orientation of individual grains. The formation and growth of recrystallization nuclei at the particles and in the matrix were examined by correlating the measured change in texture to the observed change in microstructure. It was found that prolific nucleation of grains having a wide spread...

  6. Structural use of aluminium in the construction industry

    Energy Technology Data Exchange (ETDEWEB)

    Nethercot, D.A. [Imperial Coll., London (United Kingdom)

    2002-07-01

    Examples are given of the structural use of aluminium in the Civil Engineering and Building Industries. These are taken from various periods within the past 50 years. The contrast between relatively widespread use for quite major structures in the 50' and 60's with the niche markets of today is striking. Paradoxically, availability of technical guidance, linked to professionally prepared educational material, has never been better. (orig.)

  7. Oxidation of solid aluminium-magnesium alloy doped by scandium

    International Nuclear Information System (INIS)

    The oxidation of solid aluminium-magnesium alloy with scandium was studied by means of thermogravimetry method. The kinetic and energy parameters of oxidation process were defined. The kinetics of oxidation was studied by means of thermogravimetry method. The apparent activation energy was defined as well. The products of oxidation were studied by means of X-ray analysis method. It was shown that the main products of oxidation were γ-Al2O3 and Mg O.

  8. Study of twist boundaries in aluminium. Structure and intergranular diffusion

    International Nuclear Information System (INIS)

    This research thesis addresses the study of grain boundaries in oriented crystals, and more particularly the systematic calculation of intergranular structures and energies of twist boundaries of <001> axis in aluminium, the determination of intergranular diffusion coefficients of zinc in a set of twist bi-crystals of same axis encompassing a whole range of disorientations, and the search for a correlation between these experimental results and calculated structures

  9. Wrought Aluminium Alloy Corrosion Propensity in Domestic Food Cooking Environment

    OpenAIRE

    Adeosun, S. O.; E. I. Akpan; S. A. Balogun

    2012-01-01

    The study on corrosion behaviour of wrought aluminium alloy in domestic food cooking conditions has been examined using the gravimetric approach. Flat cold rolled and annealed sheets were subjected to solutions of Capsicum annuum, L. esculentum, Allium cepa, and their blend under three conditions, namely, heating and cooling in still air, heating and cooling in refrigerator, and leaving some in open still atmosphere. Results show that corrosion occurred within the test period (288 hours) in t...

  10. Outstanding inhibitive effect of colchicine on aluminium alloy 6061 corrosion

    OpenAIRE

    Mudigere Krishnegowda Pavithra; Thimmappa Venkatarangaiah Venkateha; Mudigere Krishnegowda Punith Kumar; Nanjanagudu Subba Rao Anantha

    2015-01-01

    The corrosion protection ability of colchicine (CC) on Aluminium alloy 6061 (AA6061) in 3.5% NaCl medium was examined by potentiodynamic polarization, electrochemical impedance, and chronoamperometric techniques. About 99 % of protection efficiency was achieved by 2 mM concentration of CC in 3.5% NaCl solution.The adsorption of CC on AA6061 surface obeys Langmuir isotherm by following both physisorption and chemisorption mechanism. Variation in the surface morphology of inhibited and uninhibi...

  11. State diagram of copper-aluminium alloys after neutron irradiation

    International Nuclear Information System (INIS)

    It is ascertained that under reactor irradiation of copper-aluminium alloys (18.0-31.2 at% of Al) radiation-induced phase transformations occur, alpha-phase is decomposed into two ones with alpha'-phase precipitation, in gamma2-phase separate regions of its high-temperature disordered modification (gamma1-phase) are formed. Thermal stability of precipitations is investigated, regions of their existence are defined on the state diagram

  12. Hole quality and burr reduction in drilling aluminium sheets

    DEFF Research Database (Denmark)

    Pilny, Lukas; De Chiffre, Leonardo; Piska, Miroslav;

    2011-01-01

    Optimization of the metal drilling process requires creation of minimum amount of burrs and uniform appearance of the drilled holes. In this paper, an experimental investigation was performed on 2 mm sheets of wrought aluminium alloy Al99.7Mg0.5Cu-H24, using 1.6 and 2 mm diameter drills. Cutting ...... drilled holes was fulfilled as well as high productivity achieved. Such optimized process results in a noticeable production cost reduction....

  13. METAL MATRIX COMPOSITES BASED ON ALUMINIUM LITHIUM AND SILICON CARBIDE

    OpenAIRE

    White, J.; Hughes, I; Willis, T.; Jordan, R.

    1987-01-01

    The present study tests the feasibility of producing metal matrix composites based on aluminium-lithium alloys. The first step in this process has been to produce an MMC based on 8090 with SiC. This has been successfully produced by Alcan International using the "Osprey" spray deposition process. The raw billets have been processed initially by extrusion. The tensile properties of this material have been determined and the strength compares favourably with DC cast alloys. Modulus is improved ...

  14. Noncontact ultrasonic thickness measurements of thin aluminium sheet

    International Nuclear Information System (INIS)

    A method has been described for the noncontact ultrasonic thickness measurements of thin aluminium sheets, using a Q-switched ruby laser generation concentric with an annular electro-magnetic acoustic transducer (EMAT) detection to imitate pulse-echo system. The detected waveforms were analyzed with the cut-off frequences of the higher order lamb modes. The results show in a good egreement with micrometer measurements within 2% discrepancy. (authors). 22 refs, 6 figs

  15. Modelling of semi-liquid aluminium flow in extrusion

    OpenAIRE

    G. Skorulski; J. Piwnik

    2007-01-01

    characterizing by low cost. The significant results may be quickly applying using theory of probability. The way of modelling the deformation mechanisms during extrusion of aluminium alloys in semi - liquid phase, the way of preparing samples and experimental technique has been analysed in the following work. On the ground of received results (i.e. registrations of consecutive process steps) the grid of the flow velocity vectors on a flat sample surface was done. It allowed to draw conclusion...

  16. Uranium and thorium behavior at aluminium floating-zone refining

    International Nuclear Information System (INIS)

    Uranium and thorium behaviour during aluminium refining by crystallization from the melt is ascertained. Measurements of of uranium and thorium radioactive impurities content in high-purity aluminiumn samples using the surface α-activity method are carried out. The content of the given impurities happened to be less than 1 x 10-7 mass.%. Such purity satisfies the requirements to materials applied in the low background 71Ge detection system of gallium-germanium solar neutrino detector

  17. Melting Transition of Small Aluminium Clusters Al11-20

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; ZHANG Feng-Shou; ZHU Zhi-Yuan

    2007-01-01

    Heat capacities of small aluminium clusters Al11-20 are investigated using MD simulation with empirical manybody Gupta potential. The heat capacities of some clusters Al11, Al12, Al13 and Al19 show well-defined peaks while the heat capacities of Al15-18 indicate a gradual melting transition. The spectra of isomers obtained by quenches along the MD trajectory give good interpretation for those results.

  18. Preparation of polymeric aluminium ferric chloride from bauxite tailings

    OpenAIRE

    Ma D; Guo M; Zhang M

    2013-01-01

    Bauxite tailings are the main solid wastes in the ore dressing process. The Al2O3 and Fe2O3 contents in bauxite tailings can reach 50% and 13% respectively. The present study proposed a feasible method to use bauxite tailings to prepare polymeric aluminium ferric chloride (PAFC), a new composite inorganic polymer for water purification. Bauxite tailings roasted reacting with hydrochloric acid under air, pickle liquor which mainly contains Fe3+, Al3+ was generated, then calcium aluminate...

  19. INVESTIGATION OF THE POTENTIAL PHYSIO-PATOLOGICAL EFFECTS OF ALUMINIUM IN PATIENTS WITH ALZHEIMER SPECIFIC SYMPTOMS

    Directory of Open Access Journals (Sweden)

    Constantin Bǎlǎeț

    2013-06-01

    Full Text Available In the past few years, there has been developed an idea about the connection between the Presence of aluminium in human blood and Alzheimer disease. The goal of our study was to demonstrate that there is a connection between the aluminium in the patients’ blood (who presented specific symptoms and Alzheimer disease’s occurrence, having a physiopathological determination. Aluminium dosage in a group of patients was analyzed (according to some pre-established procedures. 65% of the patients had 1-5% higher than normal values for aluminium level. Aluminium intoxication could lead to syndromes which could affect peoples’ activity. The general physicians must be aware of the need for detecting the aluminium in blood, of interpreting the physiopathological changes and of monitoring these changes in order to detect early symptoms of Alzheimer disease.

  20. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity. PMID:27025067

  1. Modelling of detonation cellular structure in aluminium suspensions

    Science.gov (United States)

    Briand, A.; Veyssiere, B.; Khasainov, B. A.

    2010-12-01

    Heterogeneous detonations involving aluminium suspensions have been studied for many years for industrial safety policies, and for military and propulsion applications. Owing to their weak detonability and to the lack of available experimental results on the detonation cellular structure, numerical simulations provide a convenient way to improve the knowledge of such detonations. One major difficulty arising in numerical study of heterogeneous detonations involving suspensions of aluminium particles in oxidizing atmospheres is the modelling of aluminium combustion. Our previous two-step model provided results on the effect on the detonation cellular structure of particle diameter and characteristic chemical lengths. In this study, a hybrid model is incorporated in the numerical code EFAE, combining both kinetic and diffusion regimes in parallel. This more realistic model provides good agreement with the previous two-step model and confirms the correlations found between the detonation cell width, and particle diameter and characteristic lengths. Moreover, the linear dependence found between the detonation cell width and the induction length remains valid with the hybrid model.

  2. 68Ga radionuclide generator on the aluminium oxide

    International Nuclear Information System (INIS)

    The method of 68Ga generator on the base of aluminium oxide is supposed. The method includes the preliminarily treatment of the aluminium oxide by NaOH solution (0.1 mol/l) and following dynamical sorption of 68Ge maternal radionuclide on the treated aluminium oxide. Value of the 68Ge sorption makes up more than 97 %. Sorption of 68Ge is proceeding at pH water solution not more than 12, but elution the 68Ga daughterly radionuclide is carried out by HCl solution (0.1 mol/l). Testing of the 68Ga pilot radionuclide preparation shows, that the generator provides the production of 300 eluates of 68Ga preparation with output 50-70 %. The 68Ge impurities in 68Ga eluate makes up 2·10-4 %. Aluminum content in the all 68Ga fractions makes up 1 μg/ml. Influence of HCl concentration in eluent and time interval between elution on the 68Ga and 68Ge breakthrough is studied

  3. Aluminium intake by INAA of hair: The aerosol intoxication pathway

    International Nuclear Information System (INIS)

    Aluminium is present in healthy human organisms in concentrations that appear to be neither useful nor noxious. However, long term higher Al levels can produce severe bone, renal and cerebral troubles. Here we report the results of the first investigation using the Instrumental Neutron Activation Analysis of human hair aimed to assess the Al contamination in workers from aluminium industry due to aerosol inhalation. Seventy five subjects working at 'Alprom' Inc., Slatina, Romania aluminium processing plant were included in this study. The exposed subjects were casters, crane operators and rolling mill operators. Hair samples were washed with acetone-water-water-water-acetone using bi-distilled water and re-distilled-purified p.a. grade acetone and irradiated for 3 min at a thermal neutron flux of 2.3 x 1012 n/cm2s in the VVR-S reactor. Student's t-test showed the arithmetical mean values of all exposed groups to differ of the control group's one with a good statistical confidence level. In most workers the Al concentration in hair is 2 times higher than normal but in one third of the casters and in two of the rolling mill operators it is on average up to 7 times higher. Substantial Al overload can cause severe osteoporosis or encephalopathies even after retirement from activity. Protection filtering masks and medical therapy based on strong chelant drug deferoxamine are recommended, (authors)

  4. Mechanical behaviour of nitrogen-implanted aluminium alloys

    Energy Technology Data Exchange (ETDEWEB)

    Guzman, L. [Centro Materiali e Biofisica Medica, Trento (Italy); Bonini, G. [Dipt. di Ingegneria Nucleare del Politecnico, Milano (Italy); Adami, M. [Dipt. di Meccanica Strutturale, Univ. degli Studi di Trento (Italy); Ossi, P.M. [Dipt. di Ingegneria Nucleare del Politecnico, Milano (Italy)]|[Trento Univ., Povo (Italy). Dipt. di Fisica; Miotello, A. [Ist. Nazionale per la Fisica della Materia, Univ. degli Studi di Trento (Italy)]|[Trento Univ., Povo (Italy). Dipt. di Fisica; Vittori-Antisari, M. [ENEA, C.R. Casaccia, Settore Nuovi Materiali, Roma (Italy); Serventi, A.M. [ENEA, C.R. Casaccia, Settore Nuovi Materiali, Roma (Italy); Voltolini, E. [Centro Materiali e Biofisica Medica, Trento (Italy)

    1996-09-01

    The effect of nitrogen implantation into pure aluminium has been extensively explored, taking into account the variation of several physical and technological properties of the implanted layer. In particular, the formation of aluminium nitride, which occurs under specific choices of the implantation parameters, is associated with an increase in hardness. In this work, we consider two Al alloys (Al-7075 and Al-2011), frequently employed in the mechanical industry, with properties strongly dependent on the thermomechanical treatment. Molecular nitrogen bombardment at 150 keV (75 keV N{sup +}) was employed, up to a total dose of 3.10{sup 17} N cm{sup -2}, varying the substrate temperature from 373 to 473 K. The samples were then characterized with respect to composition, structure, morphology, microhardness, scratch resistance (also performing multi-pass testing) and friction coefficient. The results were interpreted within the framework of micromechanical models describing the hardness of thin coatings deposited onto soft substrates; the microhardness of the implanted layer increased by a factor of five. It appears that nitrogen-implanted aluminium alloy layers, in spite of their shallow thickness, behave better than hard TiN coated surfaces. Care must be taken to implant both alloys at the lowest possible temperature to avoid degradation of the substrate properties. (orig.)

  5. Welding metallurgy of aluminium for radiation tube of reactor

    International Nuclear Information System (INIS)

    The metallurgy of TIG weldment in aluminium alloy was examined based on physical metallurgy characteristics. The presence of weld defects have been detected by x-ray radiographic and metallographic methods. The lack of penetration in the aluminium weldment was possibly caused by the formation of aluminium oxide layer, insufficient heating flow and fast speed of work piece rotation. Segregation of major elements such as Mg and Si were varied between the weld zone and parent metal depending on the heat input during welding. Microstructure and microhardness across the weldment were markedly changed by heat-treatments. Minimum hardness was found in the heat-affected zone (HAZ) - fusion zone boundary and maximum hardness was found in the fusion zone. Both these extremes can produce premature failure of the weldment. Such failure especially embrittlement cracking could be hindered by heat-treated at 4130C, 2 1/2 hours and furnace cooled, where the distribution of hardness has been minimized and homogenized. (author)

  6. Weldability of high strength aluminium-scandium alloys

    International Nuclear Information System (INIS)

    Australia possesses a significant percentage of the world reserves of the ores required for the production of light alloys such as aluminium, magnesium and titanium. However, most of these minerals deposits are exported for processing, losing the potential of value adding benefits. Scandium has been known for some time to possess excellent grain refining properties when alloyed with aluminium. Although this adds considerable benefits to the mechanical properties of these alloys, it has not been fully exploited due to the high cost of producing the scandium metal. Deposits of scandium containing ore have recently been identified in Australia that are far more accessible than other deposits throughout the world. CSIRO Manufacturing Science and Technology had initiated a research project to investigate the effect of scandium and other grain refining additions on the properties of selected aluminium alloys in order to develop the market and maximise the potential benefits from Australian resources. The major objective of the project is to develop high strength aluminum alloys that exhibit good processing characteristics, particularly good weldability

  7. Analysis of Orthogonal Cutting of Aluminium-based Composites

    Directory of Open Access Journals (Sweden)

    P. Ravinder Reddy

    2002-10-01

    Full Text Available A turning test on aluminium-based metal-matrix composites (MMCs (aluminium-30% silicon carbide was performed with K-20 carbide tool material and wear patterns and the wear land growth rates were analysed to evaluate the wear characteristics and to classify the relationship between the physical (mechanical properties and the flank wear of cutting tools. The study was also extended to the machining aspects and the width of cuts on MMCs and the influence of various cutting parameters. The experiments were conducted to measure the temperature along the cutting tool edge using thermocouple at various cutting speeds, and depth of cuts, keeping the feed rate constant while turning with K-20 carbide cutting tool. The finite-element method was used to simulate the orthogonal cutting of aluminium-based MMCs. The heat generation at the chip-tool interface, frictional heat generation at the tool flank, and the heat generation at the work tool interface were calculated analytically and imposed as boundary conditions. The analysis of the steady-state heat transfer was carried out and the temperature distribution at cutting edge, shear zone, and interface regions have been reported.

  8. The Effect of Thickness of Aluminium Films on Optical Reflectance

    Directory of Open Access Journals (Sweden)

    Robert Lugolole

    2015-01-01

    Full Text Available In Uganda and Africa at large, up to 90% of the total energy used for food preparation and water pasteurization is from fossil fuels particularly firewood and kerosene which pollute the environment, yet there is abundant solar energy throughout the year, which could also be used. Uganda is abundantly rich in clay minerals such as ball clay, kaolin, feldspar, and quartz from which ceramic substrates were developed. Aluminium films of different thicknesses were deposited on different substrates in the diffusion pump microprocessor vacuum coater (Edwards AUTO 306. The optical reflectance of the aluminium films was obtained using a spectrophotometer (SolidSpec-3700/DUV-UV-VIS-NIR at various wave lengths. The analysis of the results of the study revealed that the optical reflectance of the aluminium films was above 50% and increased with increasing film thickness and wavelength. Thus, this method can be used to produce reflector systems in the technology of solar cooking and other appliances which use solar energy.

  9. Effect of ultrasonic energy on nanoscale interfacial structure in copper wire bonding on aluminium pads

    International Nuclear Information System (INIS)

    The effect of ultrasonic vibration on nanoscale interfacial structure of thermosonic copper wire bonding on aluminium pads was investigated. It was found that bonding strength was determined by the extent of fragmentation of a native aluminium oxide overlayer (5-10 nm thick) on aluminium pads, forming paths for formation of intermetallic compound CuAl2 in areas of direct contact of bonded metal surfaces. The degree of fracture of the oxide layer was strongly affected by a level of ultrasonic power.

  10. Subgrain Growth, Recovery Kinetics and Nucleation of Recrystallization of Cold Deformed Aluminium Alloys

    OpenAIRE

    Bunkholt, Sindre

    2013-01-01

    Phenomena related to annealing of aluminium alloys are among the least understood in aluminium metallurgy but very important for industrial thermo-mechanical processing i.e. deformation and annealing. Physical models are used to predict recovery and recrystallization behaviour, and associated material properties, industrially. However, alloy development, e.g. to incorporate more recycled aluminium, has shown that current softening models are not satisfactory. Thus, improvements do require a b...

  11. Selected properties of the aluminium alloy base composites reinforced with intermetallic particles

    OpenAIRE

    M. Adamiak

    2005-01-01

    Purpose: The main aim of this work is to investigate two types of intermetallics TiAl and Ti3Al as reinforcement and their influence on selected properties and microstructure of aluminium matrix composites.Design/methodology/approach: Aluminium matrix composites were produced employing the atomised aluminium alloy AA6061 as metal matrix, when as reinforcement TiAl and Ti3Al intermetallics particles were used. The powders were cold pressed and then hot extruded. To evaluate the effect of mecha...

  12. Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

    OpenAIRE

    Sinou, Jean-Jacques; Macquaire, Bruno

    2003-01-01

    International audience For a car manufacturer, reducing the weight of vehicles is an obvious aim. Replacing steel by aluminium moves towards that goal. Unfortunately, aluminium's stamping numerical simulation results are not yet as reliable as those of steel. Punch-strength and spring-back phenomena are not correctly described. This study on aluminium validates the behaviour law Hill 48 quadratic yield criterion with both isotropic and kinematic hardening. It is based on the yield surface ...

  13. Electrodeposition of aluminium film on P90 Li-Al alloy as protective coating against corrosion

    OpenAIRE

    U. Bardi; Caporali, S; M. Craig; A. Giorgetti; Perissi, I; Nicholls, J. R.

    2009-01-01

    In this paper we report on the electrodeposition of thin aluminium layers on P90 lithium–aluminium alloy at room temperature from a chloroaluminate ionic liquid (1-butyl-3-methyl imidazolium heptachloroaluminate [BMIm]Al2Cl7). We found that the treatment of the P90 sample's surface is a key point to obtain good quality coatings. On freshly mechanically polished surfaces, thin (about 24 µm), homogeneous and dense aluminium layers were obtained at 10 µm h− 1 deposition rate. F...

  14. Improvement in Wear Properties of a Hypereutectic Aluminium Silicon Alloy with Manganese

    OpenAIRE

    Prabhkiran Kaur; D.K. Dwivedi; P.M. Pathak; Sunil Kumar

    2014-01-01

    Improvement in wear properties of rare earth Cerium base hypereutectic Aluminium-Silicon alloy with Manganese modification has been reported in this paper. Wear studies were carried out on cast samples of hypereutectic Aluminium-Silicon alloy (Al-Si) with rare earth Cerium oxide (CeO2) and Manganese (Mn) modification. Final wear properties of rare earth Cerium oxide and Manganese modified hypereutectic Aluminium Silicon alloy were compared with the values of author?s previous work on rare ear...

  15. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    OpenAIRE

    Mold, M; Shardlow, E; Exley, C.

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, pote...

  16. Determination of aluminium contents in selected food samples by instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Food and food products are the main sources of Aluminium entering the human body. In order to know aluminium contents in food and food products, selected 26 samples from local market were analyzed by instrumental neutron activation analysis (INAA) using reactor neutrons and high resolution gamma-ray spectrometry. INAA using 1,779 keV γ-ray of 28Al (2.24 min) was used for aluminium concentrations in the range of 33-529 mg kg-1. Two NIST standard reference materials (SRMs) and two IAEA reference materials (RMs) were analyzed by INAA for quantification of aluminium as a part of method validation. (author)

  17. Comparison of the x-ray attenuation properties of breast calcifications, aluminium, hydroxyapatite and calcium oxalate

    International Nuclear Information System (INIS)

    Aluminium is often used as a substitute material for calcifications in phantom measurements in mammography. Additionally, calcium oxalate, hydroxyapatite and aluminium are used in simulation studies. This assumes that these materials have similar attenuation properties to calcification, and this assumption is examined in this work. Sliced mastectomy samples containing calcification were imaged at ×5 magnification using a digital specimen cabinet. Images of the individual calcifications were extracted, and the diameter and contrast of each calculated. The thicknesses of aluminium required to achieve the same contrast as each calcification when imaged under the same conditions were calculated using measurements of the contrast of aluminium foils. As hydroxyapatite and calcium oxalate are also used to simulate calcifications, the equivalent aluminium thicknesses of these materials were also calculated using tabulated attenuation coefficients. On average the equivalent aluminium thickness was 0.85 times the calcification diameter. For calcium oxalate and hydroxyapatite, the equivalent aluminium thicknesses were 1.01 and 2.19 times the thickness of these materials respectively. Aluminium and calcium oxalate are suitable substitute materials for calcifications. Hydroxyapatite is much more attenuating than the calcifications and aluminium. Using solid hydroxyapatite as a substitute for calcification of the same size would lead to excessive contrast in the mammographic image. (note)

  18. Low temperature oxidation of niobium alloy with silicon-aluminium coating

    International Nuclear Information System (INIS)

    Using the gravimetry methods heat resistance of niobium-titanium-aluminium alloy in the air and at 700 deg C in the initial state and when it is protected by silicide-aluminium coatings (with variable content of aluminium) is investigated. Using X-ray diffraction and micro X-ray diffraction analyses, mechanisms of the alloy oxidation and the coating protective effect are studied. The role of aluminium in the formation of coatings is analyzed and according to bend tests the plasticity of the coatings is evaluated

  19. Thermoelectric power in low-density interstitial-free iron-aluminium alloys

    Science.gov (United States)

    Rana, Radhakanta; Liu, Cheng

    2013-09-01

    Thermoelectric power (TEP) studies on low-density interstitial-free iron-aluminium alloys reveal that the TEP decreases with increase in the aluminium content on account of the introduction of lattice dispersion centres. The TEP coefficients, determined from the Nordheim-Gorter law, for 6.8 and 8.1 wt.% aluminium additions to α-iron are found to be higher than values reported in previous literature for small aluminium additions. The grain size has a very weak effect on the TEP of these alloys.

  20. Wear and chemistry of zirconium-silicate, aluminium-silicate and zirconium-aluminium-silicate glasses in alkaline medium

    International Nuclear Information System (INIS)

    A study of the chemical durability, in alkaline solutions, of zirconium silicate, aluminium silicate, zirconium/aluminium silicate glasses as a function of glass composition is carried out. The glasses were tested using standard DIN-52322 method, where the glass samples are prepared in small polished pieces and attacked for 3 hours in a 800 ml solution of 1N (NaOH + NA2CO3) at 970C. The results show that the presence of ZrO2 in the glass composition increases its chemical durability to alkaline attack. Glasses of the aluminium/zirconium silicate series were melted with and without TiO2. It was shown experimentally that for this series of glasses, the presence of both TiO2 and ZrO2 gave better chemical durability results. However, the best overall results were obtained from the simpler zirconium silicate glasses, where it was possible to make glasses with higher values of ZrO2. (Author)

  1. Modifications study of the electronic structure of silicon oxides (α-SiO2), aluminium oxides (α-Al2O3) and yttrium oxides (Y2O3), induced by structural defects (non-stoichiometry, mechanical strains, high energy ions irradiation)

    International Nuclear Information System (INIS)

    Structure defects effects on electronic structure were studied experimentally (X absorption spectroscopy and photoelectron spectroscopy) and theoretically (state density calculus based on high binding strengths). This thesis is divided into three parts: oxygen stoichiometry effect on yttrium oxide (Y2O3) electronic structure, mechanical strain effect on quartz-α (SiO2) electronic structure, high energy ions irradiation effects on quartz-α. (A.B.). refs., figs., tabs

  2. Corrosion of research reactor aluminium-clad spent fuel at wet storage

    International Nuclear Information System (INIS)

    Full text: About 700 research reactors (RRs) and critical assemblies have been built worldwide. Of these about 260 are presently operational. A large variety of spent fuels with different fuel meats, different geometries and different enrichments in 235U are presently stored under water in basins located throughout the world while awaiting final disposition or shipment to the USA or to the Russian Federation. At some reactor sites, the spent fuel has been in water for up to 40 years. More than 90% of these fuels are clad in aluminium or aluminium based alloys that are susceptible to corrosion in water of less than optimum quality. Some fuel is stored in reactor pools themselves, some in auxiliary pools (or basins) close to the reactor and some in away-from-reactor pools. Corrosion induced degradation of fuel cladding, the underlying fuel itself, other aluminium components of the fuel handling and storage systems, especially pool liners, has been observed in many of the pools. As a result of these corrosion issues, the IAEA implemented in 1996 a Coordinated Research Project (CRP) on 'Corrosion of Research Reactor Aluminium-Clad Spent Fuel in Water'. The objectives of the CRP were to: (a) establish uniform practices for corrosion monitoring and surveillance, (b) provide a technical basis for continued wet storage of RR spent fuel, (c) collect data to help predict fuel cladding lifetimes and (d) establish procedures for characterization of water in fuel storage basins. Phase-I of this CRP ended in 2000 and Phase-II is ongoing with 8 participating countries, including Kazakhstan. The CRP consisted of exposure of standard racks of corrosion coupons in the spent fuel pools of the participating countries and evaluation of the coupons after predetermined exposure times, along with periodic monitoring of the storage basin water. The materials selected for testing were representative of typical Al cladding alloys used in RR fuel, handling tools and storage racks. The

  3. The examinations on purity of ion beams emitted by plasmatic and thermoemission ion source

    International Nuclear Information System (INIS)

    The composition of ion beam emitted by both Nielsen's type of plasmatic ion source and source with superficial ionization was examined. Investigations were connected with a design of simplified and chapper variant of implantator without ion beam analysis in magnetic field. The measurements were carried out using an isotope electromagnetic separator in the Institute of Physics at the Maria Curie-Sklodowska University in Lublin. A considerable differentation in ion beam in respect of both ion charge and kind was observed. The impurities were caused by gases absorbed in source elements as well as by residual gases filled the apparatus. An important reason of impurities seems to be also a source ''store'' due to previous separations. The methods which enable to obtain pure ion beams of argon, nitrogen, zinc and aluminium are presented. Besides the optimum conditions for source work the pure ion beams are determined. (author)

  4. Examinations on purity of ion beams emitted by plasmatic and thermoemission ion source

    Energy Technology Data Exchange (ETDEWEB)

    Maczka, D.; Mazur, J.; Wasiak, A. (Uniwersytet Marii Curie-Sklodowskiej, Lublin (Poland). Inst. Fizyki)

    1981-01-01

    The composition of ion beam emitted by both Nielsen's type of plasmatic ion source and source with superficial ionization was examined. Investigations were connected with a design of simplified and chapper variant of implantator without ion beam analysis in magnetic field. The measurements were carried out using an isotope electromagnetic separator in the Institute of Physics at the Maria Curie-Sklodowska University in Lublin. A considerable differentation in ion beam in respect of both ion charge and kind was observed. The impurities were caused by gases absorbed in source elements as well as by residual gases filled the apparatus. An important reason of impurities seems to be also a source ''store'' due to previous separations. The methods which enable to obtain pure ion beams of argon, nitrogen, zinc and aluminium are presented. Besides the optimum conditions for source work the pure ion beams are determined.

  5. Element- and charge-state-resolved ion energies in the cathodic arc plasma from composite AlCr cathodes in argon, nitrogen and oxygen atmospheres

    OpenAIRE

    Franz, Robert; Polcik, Peter; Anders, André

    2014-01-01

    The energy distribution functions of ions in the cathodic arc plasma using composite AlCr cathodes were measured as a function of the background gas pressure in the range 0.5 to 3.5 Pa for different cathode compositions and gas atmospheres. The most abundant aluminium ions were Al$^{+}$ regardless of the background gas species, whereas Cr$^{2+}$ ions were dominating in Ar and N$_2$ and Cr$^{+}$ in O$_2$ atmospheres. The energy distributions of the aluminium and chromium ions typically consist...

  6. Enhancement of wear and ballistic resistance of armour grade AA7075 aluminium alloy using friction stir processing

    OpenAIRE

    I. Sudhakar; V. Madhu; G. Madhusudhan Reddy; K. Srinivasa Rao

    2015-01-01

    Industrial applications of aluminium and its alloys are restricted because of their poor tribological properties. Thermal spraying, laser surfacing, electron beam welding are the most widely used techniques to alter the surface morphology of base metal. Preliminary studies reveal that the coating and layering of aluminium alloys with ceramic particles enhance the ballistic resistance. Furthermore, among aluminium alloys, 7075 aluminium alloy exhibits high strength which can be compared to tha...

  7. Fast ignition driven by quasi-monoenergetic ions: Optimal ion type and reduction of ignition energies with an ion beam array

    CERN Document Server

    Honrubia, J J; Hegelich, B M; Murakami, M; Enriquez, C D

    2014-01-01

    Fast ignition of inertial fusion targets driven by quasi-monoenergetic ion beams is investigated by means of numerical simulations. Light and intermediate ions such as lithium, carbon, aluminium and vanadium have been considered. Simulations show that the minimum ignition energies of an ideal configuration of compressed Deuterium-Tritium are almost independent on the ion atomic number. However, they are obtained for increasing ion energies, which scale, approximately, as Z^2, where Z is the ion atomic number. Assuming that the ion beam can be focused into 10 {\\mu}m spots, a new irradiation scheme is proposed to reduce the ignition energies. The combination of intermediate Z ions, such as 5.5 GeV vanadium, and the new irradiation scheme allows a reduction of the number of ions required for ignition by, roughly, three orders of magnitude when compared with the standard proton fast ignition scheme.

  8. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    Directory of Open Access Journals (Sweden)

    N. S. Ahmad Zauzi

    2016-01-01

    Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

  9. Void formation in pure aluminium irradiated with high-energetic electron beams and gamma-quanta

    DEFF Research Database (Denmark)

    Gan, V. V.; Ozhigou, L. S.; Yamnitsky, V. A.; Singh, Bachu Narain; Leffers, Torben; Bilde-Sørensen, Jørgen

    The spatial distribution of displaced atoms and helium atoms and also the spectra of damaging energies of primary displaced atoms in a thick aluminium target irradiated with electrons of 225 MeV energy were calculated. Pure aluminium (99.9999%) irradiated up to 0.04 dose was studied by electron...

  10. The effect of aluminium chlorhydrate on sweat gland activity in cattle.

    Science.gov (United States)

    Rees-Jones, A M; Jenkinson, D M

    1978-03-01

    Topical application of aluminium chlorhydrate had no appreciable antiperspirant action on the epitrichial glands of cattle. There was no evidence of penetration of the salt into the dermis or of any change in the morphology of the glands. It is probable that the antiperspirant activity of aluminium chlorhydrate in the human axilla, is only on the atrichial glands. PMID:632617

  11. Fatigue testing of large scale details of a large size aluminium surface effect ship

    NARCIS (Netherlands)

    Dijkstra, O.D.; Vredeveldt, A.W.; Janssen, G.Th.M.; Ortmans, P.

    1998-01-01

    The paper presents the results of two large scale fatigue tests on a detail of an aluminium surface effect ship. The overall dimensions of the specimens were: length 4.8 m, height 3.2 m and width 1.5 m (equal to the main frame spacing). The specimens consist of an aluminium structure of welded plate

  12. Synthesis and reactivity of aluminium nitride obtained by action of ammonia on alumina

    International Nuclear Information System (INIS)

    Aluminium nitride is a ceramic with potential nuclear applications because of its exceptional structural resistance to neutrons. To improve quality and reactivity a new preparation process by reaction between ammonia and alumina is presented. The aluminium nitride thus obtained, white colored, is pure and its reactivity gives an useful product for a lot of synthesis in the area of nitrided ceramics and glasses

  13. Synthesis and reactivity of aluminium nitride obtained by action of ammonia on alumina

    Energy Technology Data Exchange (ETDEWEB)

    Rocherulle, J.; Guyader, J.; Verdier, P.; Laurent, Y.

    1985-01-01

    Aluminium nitride is a ceramic with potential nuclear applications because of its exceptional structural resistance to neutrons. To improve quality and reactivity a new preparation process by reaction between ammonia and alumina is presented. The aluminium nitride thus obtained, white colored, is pure and its reactivity gives an useful product for a lot of synthesis in the area of nitrided ceramics and glasses.

  14. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-01-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain. PMID:27515230

  15. The role of magnesium in the electrochemical behaviour of 5XXX aluminium-magnesium alloys

    NARCIS (Netherlands)

    Flores Ramirez, J.R.

    2006-01-01

    An investigation concerning the effects of magnesium on the intergranular corrosion susceptibility of AA5XXX aluminium alloys was carried out. In the present work, magnesium is found to be highly mobile in the bulk metal as well as in the aluminium oxide. This mobility is also found to be dependent

  16. European welding technology for an Australian yacht in aluminium; Soudage a l'europeenne pour un yacht australien en aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2005-02-01

    It is a European welding technology which has been retained for the Australian shipbuilding yard: 'Shipworks' for manufacturing a luxury yacht in aluminium. This yacht has been manufactured under the American standards specifications. (O.M.)

  17. TEM microstructure investigations of aluminium alloys used for laser alloying

    Directory of Open Access Journals (Sweden)

    K. Labisz

    2012-12-01

    Full Text Available Purpose: In this paper there are presented results of Transmission Electron Microscope investigation concerning the structure of the AlSi7Cu4 cast aluminium alloy using for alloying and remelting with the high power diode laser (HPDL. There are also presented the results of the thermo-derivative analysis performed using the UMSA (Universal Metallurgical Simulator and Analyser device, allowing to determine the specific points of the solidifying alloy, what is helpful for phase determination occurred in this alloy. In this work especially the changes of the precipitation type, size and shape were determined.Design/methodology/approach: The investigations were performed using electron microscopy for the microstructure and phases determination. By mind of the transmission electron microscopy, especially selected area diffraction method appliance it was possible to determine the phases occurred in the alloy in the as cast state. The morphology and size of the Mg2Si was also possible to determine as well the lattice parameters for this phase.Findings: : The reason of this work was also to present the laser treatment technology, which will be used for further alloying and remelting with ceramic powders – especially carbides and oxides. Particularly the overview will be directed on the laser power to achieve good layer hardness for protection of this hot work tool steel from losing their work stability and to make the tool surface more resistant to action in external conditions. The structure of the surface laser tray changes in a way, that there are very high roughness of the surface zone and the flatness or geometry changes in an important manner, crucial for further investigation.Research limitations/implications: The aluminium samples were examined metallographically using transmission electron microscope with different image techniques.Practical implications: Developing of new technology with appliance of Al alloys, High Power Diode Laser and

  18. Effects of silicon on gastrointestinal absorption of aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Edwardson, J.A.; Moore, P.B.; Ferrier, I.N.; Lilley, J.S.; Newton, G.W.A.; Barker, J.; Templar, J.; Day, J.P.

    1993-07-24

    The reported geographical association between Alzheimer's disease and levels of aluminium (Al) in water supplies may reflect the inverse relation between Al and silicon (Si) concentrations in water, and the potential for Si to reduce the bioavailability of the metal. The authors tested this hypothesis using isotopic [sup 26]Al tracer administered orally to five healthy volunteers in the presence and absence of Si. Dissolved Si, at a concentration found in some water supplies reduced the peak plasma [sup 26]Al concentration to 15% of the value obtained in the absence of Si. The results indicate that dissolved Si is an important factor in limiting the absorption of dietary Al.

  19. Interface reaction in aluminium matrix composite at laser welding

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Interface reaction of SiCw/6061Al aluminium matrix composite subjected to laser welding was studied. It is pointed out that the main reason for bad weldability of the material is concerned with the interface reaction during the welding. Effects of welding parameters on interface reaction were also investigated. The results show that the interface bonding state can be improved by laser beam, and the main welding parameter affecting the strength of weld is laser output power. The smaller the output power, the lower the extent of interface reaction and the better the mechanical properties.

  20. Fatigue behaviour of 6061 aluminium alloy and its composite

    OpenAIRE

    Hwa, Ping

    2001-01-01

    Fatigue behaviour of an artificial aged powder metallurgy 6061 aluminium alloy, and a composite made of this alloy with 15% volume fraction of SiCp was investigated. The alloy was subjected to T6 heat treatment, as was the composite material chosen (which incorporated SiC particles of average size 30pm). An extensive experimental programme was carried out in which fatigue lives were determined using load-controlled axial loading of unnotched cylindrical samples, at stress ratios of-1 and 0.1....

  1. Slip lines in scandium and lithium containing aluminium alloys

    International Nuclear Information System (INIS)

    Intensive slip lines in cold rolled sheets of scandium or lithium containing aluminium base alloys are under study. Slip lines are shown to be the places of concentrated shear strain which arise due to the occurrence of secondary δ'(Al3Li) and Al3Sc particles completely coherent to the matrix. The formation of slip lines has a detrimental effect on cold rolled sheet mechanical properties after heat hardening. To avoid the appearance of slip lines it is necessary to roll sheets with low reductions in area and to choose appropriate conditions of intermediate heat treatments. 5 refs., 5 figs., 2 tabs

  2. Damage of repeatedly nitrocarburised steel dies for aluminium extrusion

    OpenAIRE

    Firrao, Donato; Scavino, Giorgio; Matteis, Paolo

    2009-01-01

    The dies employed for the hot extrusion of aluminium alloys are subjected to repeated cycles of nitriding, or nitrocarburising, after service periods of given length. Three dies, fabricated with ISO X40CrMoV5-1 (AISI H13) steel and liquid nitrocarburised, were examined either in the asfabricated condition, or after one service period, or after 12 nitrocarburising and service cycles (end of life). Samples cut from the die subjected to one service period were re-nitrocarburised for increasing d...

  3. Physical model of aluminium refining process in URC-7000

    Directory of Open Access Journals (Sweden)

    M. Saternus

    2009-07-01

    Full Text Available The paper presents short characteristics of the most frequently used reactors for the continuous refining of aluminium and its alloys. Refining depends on the flow rate of refining gas. It influences the shape and size of gas bubbles. So the physical model was created to determine the level of gas bubble dispersion in liquids. Schemes of gas dispersion in liquid metal were presented taking into consideration that the gas flow rate is changing from 2 to 30 dm3/min. The range selection of the flow rate of refining gas value for five patterns of the dispersion (no dispersion, minimum, intimate, uniform and overdispersion was also done.

  4. The fracture of boron fibre-reinforced 6061 aluminium alloy

    Science.gov (United States)

    Wright, M. A.; Welch, D.; Jollay, J.

    1979-01-01

    The fracture of 6061 aluminium alloy reinforced with unidirectional and cross-plied 0/90 deg, 0/90/+ or - 45 deg boron fibres has been investigated. The results have been described in terms of a critical stress intensity, K(Q). Critical stress intensity factors were obtained by substituting the failure stress and the initial crack length into the appropriate expression for K(Q). Values were obtained that depended on the dimensions of the specimens. It was therefore concluded that, for the size of specimen tested, the values of K(Q) did not reflect any basic materials property.

  5. Determination of phosphorus in hypereutectic aluminium-silicon alloys.

    Science.gov (United States)

    Mukai, K

    1972-04-01

    A reproducible method is described for determination of small amounts of phosphorus (from 0.0005% to 0.02%) in hypereutectic aluminium-silicon complex alloys. The method permits the separate determination of phosphorus in acid-soluble and acid-insoluble fractions. Phosphomolybdate is extracted with n-butanol-chloroform solvent mixture and back-extracted with a btannous chloride reducing solution. The phosphorus content of a sample cut into small pieces decreases during storage; loss of phosphorus is negligible on acid dissolution under oxidizing conditions. PMID:18961077

  6. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    DEFF Research Database (Denmark)

    Aggerbeck, Martin

    that the roughness after etching increases with higher amounts of alloying elements (especially iron and silicon). Proper polishing requires some alloy hardness, while alloy purity is required for a glossy appearance after anodisation. Magnetron sputtered aluminium based coatings containing up to 18 wt...... the optical effect of partially oxidised intermetallics and the subsurface morphology after anodisation. It was suggested, that the darkening of the anodised specimens happened due to roughness of the oxide-substrate interface causing light trapping and optical scattering and absorption by the...

  7. Multi-element study in aluminium by activation analysis technique

    International Nuclear Information System (INIS)

    The instrumental activation analysis is a technique relatively quickly that help to know the elemental composition of materials. It is used mainly in the trace elements determination but in the case of major elements it is necessary to make some considerations as the different nuclear reactions carried out due to the neutron flux is a mixture of thermal and fast neutrons. This could be interpreted for the presence and or erroneous quantification about some elements. In this work, is described the way in which was analyzed a container piece with approximately a 85% of aluminium. The elements Zn, Mn, Sb, Ga, Cu, Cl and Sm were determined. (Author)

  8. Modeling of recrystallization texture of aluminium: symmetric and asymmetric rolling

    Science.gov (United States)

    Wierzbanowski, K.; Kotra, M.; Wronski, M.; Sztwiertnia, K.; Wronski, S.; Lodini, A.

    2015-04-01

    In some metallic materials the dominating recrystallization mechanism can be described by the oriented growth behaviour. Phenomenological laws state that in selected materials only these nuclei grow intensively which have a given misorientation relation with the deformed matrix. This description is frequently verified in f.c.c. metals and generally reported misorientations correspond approximately to 400 rotation around the axis. Basing on the above ideas the recrystallization model, including the compromise condition, was formulated and applied to the study of recrystallization textures of rolled polycrystalline aluminium.

  9. Design considerations for HFQ® hot stamped aluminium structural panels

    Directory of Open Access Journals (Sweden)

    Foster Alistair

    2015-01-01

    Full Text Available HFQ is a deep drawing process for alloyed aluminium sheet that can be used to produce complex-stamped forms while maintaining the high-strength of 6xxx and 7xxx alloys. By adopting a strategy to design for HFQ at the platform level, designers can reduce part count (thereby reducing cost and weight, reduce gauge (thereby reducing weight, and improve part packaging. Two simple design examples are given to assist designers in evolving traditionally formed panel designs to HFQ formed solutions. Example features are used to illustrate the effect of geometry, thickness and strength on the final structural component.

  10. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    OpenAIRE

    Aggerbeck, Martin; Ambat, Rajan

    2014-01-01

    I dette projekt blev muligheden for at designe aluminiumsbaserede coatings undersøgt med fokus på hvordan den kemiske sammensætning og overfladens beskaffenhed påvirker den visuelle fremtoning og de basiske korrosionsegenskaber med titan anvendt som det primære legeringselement. De primære resultater og diskussioner fra dette arbejde præsenteres i form af i bilag som fire artikelmanuskripter indsendt til publikation i tidsskrifter. Anvendelsen af aluminium er bred, fra transportmidler, bygnin...

  11. The effect of atmospheric corona treatment on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.;

    2010-01-01

    The effect of atmospheric corona discharge on AM 050 aluminium surface was investigated using electrochemical polarization, SEM-EDX, FIB-SEM. and XPS. The corona treatment was performed with varying time (1, 5, and 15 min) in atmospheric air. A 200 nm oxide layer was generated on AA1050 after the...... 15 min air corona treatment. A significant reduction in anodic and cathodic reactivities was observed starting from 1 min exposure, which further decreased with prolonged exposure (15 min) and after delayed testing (after 30 days). The reduction in surface reactivity is due to the formation of...

  12. Radiation Induced Removal of Stacking Faults in Quenched Aluminium

    International Nuclear Information System (INIS)

    The effect of neutron irradiation on specimens of quenched aluminium containing Frank sessile dislocation loops has been studied by means of electron microscopy. The Frank loops were found to trans. form into perfect loops at doses less than 1017 nvt. A possible reason for the removal of the stacking faults is the displacement of a number of atoms at the faults, leading to the passage of a Shockley partial. Unfaulting induced by stress fields from dislocations, released during the irradiation, can also be important

  13. Nouveau procédé de synthèse du nitrure d'aluminium

    OpenAIRE

    Haussonne, J.; Lostec, J.; Bertot, J.; Lostec, L.; Sadou, S.

    1993-01-01

    Les calculs thermodynamiques montrent que, même à température ambiante, l'aluminium pur peut réagir avec l'azote pour former le nitrure d'aluminium AlN. Cependant, la poudre d'aluminium pur n'existe pas : ses grains sont toujours entourés d'une couche d'alumine protectrice. De plus, dans l'hypothèse où l'on pourrait faire réagir de la poudre d'aluminium avec de l'azote, il se formerait de même une couche protectrice de nitrure d'aluminium qui empêcherait le centre des grains de réagir. S'insp...

  14. The influence of aluminium upon electronic transport in r.f. sputtered amorphous Si:H

    International Nuclear Information System (INIS)

    A range of specimens has been prepared in which aluminium is introduced into hydrogenated amorphous silicon by a co-sputtering technique. With increasing aluminium content, the activation energy of the dark d.c. conductivity and the optical energy gap are both found to decrease, whilst the magnitude of the d.c. conductivity is increased at all temperatures within the range of study. The inclusion of aluminium is found to quench the photoconductivity to a level below the resolution of the measurement system. Thermoelectric power measurements on films with a high aluminium content indicate that transport is dominated by holes. The data are interpreted in terms of the semiconducting properties of a silicon - aluminium alloy. High-temperature transport is dominated by holes in extended valence-band states, whilst at low temperatures carrier motion is through localized states situated between the Fermi level and the valence-band mobility edge. (author)

  15. Influence of aluminium upon electronic transport in RF sputtered amorphous Si:H

    Energy Technology Data Exchange (ETDEWEB)

    Fortuna, H.S.; Marshall, J.M.

    1986-05-01

    A range of specimens has been prepared in which aluminium is introduced into hydrogenated amorphous silicon by a co-sputtering technique. With increasing aluminium content, the activation energy of the dark d.c. conductivity and the optical energy gap are both found to decrease, whilst the magnitude of the d.c. conductivity is increased at all temperatures within the range of study. The inclusion of aluminium is found to quench the photoconductivity to a level below the resolution of the measurement system. Thermoelectric power measurements on films with a high aluminium content indicate that transport is dominated by holes. The data are interpreted in terms of the semiconducting properties of a silicon -aluminium alloy. High-temperature transport is dominated by holes in extended valence-band states, whilst at low temperatures carrier motion is through localized states situated between the Fermi level and the valence-band mobility edge.

  16. Low-temperature Electrodeposition of Aluminium from Lewis Acidic 1-Allyl-3-methylimidazolium Chloroaluminate Ionic Liquids

    Institute of Scientific and Technical Information of China (English)

    郑勇; 张锁江; 吕兴梅; 王倩; 左勇; 刘恋

    2012-01-01

    Lewis acidic 1-allyl-3-methylimidazolium chloroaluminate ionic liquids were used as promising electrolytes in the low-temperature electrodeposition of aluminium. Systematic studies on deposition process have been performed by cYClic voltammetry and chronoamperometry. The surface morphology and X-ray diffraction (XRD) patterns of deposits prepared at different experimental conditions were also investigated. It was shown that the nucleation density and growth rate of crystallites had a great effect on the structure of aluminium deposited. The crys- tallographic orientation of deposits was mainly influenced by temperature and current density. Smooth, dense and well adherent aluminium coatings were obtained on copper substrates at 10-25 mA.cm^-2 and 313.2-353.2 K. More- over, the current efficiency of deposition and purity of aluminium have been significantly improved, demonstrating that the ionic liquids tested have a prospectful potential in electroplating and electrorefining of aluminium.

  17. Production and some properties of Si3N4 reinforced aluminium alloy composites

    Directory of Open Access Journals (Sweden)

    Pardeep Sharma

    2015-09-01

    Full Text Available The present research work focuses on the production of aluminium (AA6082-T6 matrix composites reinforced with various weight percentage of silicon nitride particles by conventional stir casting route. The percentage of reinforcement is varied from 0 wt.% to 12 wt.% in a stage of 3%. The microstructures and mechanical properties of the fabricated aluminium matrix composites are investigated. The scanning electron microstructure images reveal the presence of Si3N4 particles in the aluminium matrix. The distribution of Si3N4 particles has also been recognized with X-ray diffraction technique. The mechanical properties such as ultimate tensile strength and hardness have improved at the cost of reduction in ductility with increase in weight percentage of silicon nitride particulates in the aluminium metal matrix. The density and porosity of the composites also show an increasing trend with increase in volume fraction of Si3N4 particles in the aluminium matrix.

  18. Electrodeposition of gallium and zinc onto aluminium. Influence of the electrodeposited metals on the activation process

    International Nuclear Information System (INIS)

    The electrodeposition of gallium and/or zinc on aluminium, aluminium-zinc alloy and vitreous carbon electrodes in chloride solutions is analysed. The electrodissolution of the formed interfaces is also described and discussed. For this purpose, potentiodynamic and potentiostatic techniques and open circuit potential measurements were employed and surface characterisation was performed by scanning electron microscopy and energy dispersive X-ray analysis. The presence of zinc, electrodeposited from the solution or as an alloying component, facilitates gallium enrichment at the interface and improves the wetting on the aluminium oxide. These conditions ensure the formation of a surface Ga-Al amalgam. As a result, the dissolution process occurs at potentials which are more active than those observed for aluminium or aluminium-zinc alloy in halide solutions

  19. REMOV TRACE MERCURY(II REMOVAL OF TRACE AMOUNTS OF MERCURY(II USING HYDRO COLLECTOR ALUMINIUM HYDROXIDE AS THE COLLECTOR

    Directory of Open Access Journals (Sweden)

    N. Rajesh

    2003-12-01

    Full Text Available A method for the removal of trace amounts of mercury (II using aluminium hydroxide as the collector. Dithizone in carbon tetrachloride was used for the extraction of mercury. The amount of Hg (II was varied from 40 mg to 100 mg. The sample volume was varied until 50ml and the level of extraction of mercury was recorded. It was found that the recovery was satisfactory until a sample volume of 25 ml, beyond which the recovery gradually decreased. The effect of interfering ions was studied at different concentrations of mercury and was found to be minimum.

  20. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Horsewell, Andy; Sommer, W. F.;

    1986-01-01

    Samples of pure aluminium (99.9999%) and commercial Al-2.7%Mg(AlMg3) and Al-1.1%Mg-0.5%Si(Al6061) alloys were irradiated with 800 MeV protons at the Los Alamos Meson Physics Facility (LAMPF) at a temperature between 40-100°C to a maximum dose of 0.2 dpa. Transmission electron microscopy (TEM) sho...... higher than in the pure Al. The amount of gas accumulation at grain boundaries was found to depend on gas generation rate, alloying and cold-work microstructure...

  1. Trace analysis measurements in high-purity aluminium by means of radiochemical neutron and proton activation analysis

    International Nuclear Information System (INIS)

    The aim of the study consisted in the development of efficient radiochemical composite processes and activation methods for the multi-element determination of traces within the lower ng range in high-purity aluminium. More than 50 elements were determined with the help of activation with reactor neutrons; the selective separation of matrix activity (adsorption with hydrated antimony pentoxide) led to a noticeable improvement of detectability, as compared with instrumental neutron activation analysis. Further improvements were achieved with the help of radiochemical group separations in ion exchangers or with the help of the selective separation of the pure beta-emitting elements. Over 20 elements up to high atomic numbers were determined by means of activating 13 MeV protons and 23 Me protons. In this connection, improvements of the detection limit by as a factor of 10 were achieved with radiochemical separation techniques, as compared with pure instrumental proton activation analysis. (RB)

  2. Ion-atom collisions for materials study

    International Nuclear Information System (INIS)

    The diffusion process of silver in aluminium was studied in thin films as a function of temperature, the most important characteristics of dispersor atoms that technique permits us to study are the atomic mass and depth into the solid. This is possible because when a sample is bombarded with ions of a given energy, the ions are dispersed with different energies for different masses and depths, hence this technique is a useful instrument for research into the physical processes which ocurr in thin films up to depths of several microns, one of the results obtained after the bombardment of the target with protons having an energy of 650 KeV was that when the target reached a temperature of approximately 400C, 800C, 1100C and 1600C during 15 minutes and the spectra of heated and unheated targets were compared it was found that the aluminium peak, the valley, the silver peak and the peak over the silver peak change with the increase of temperature and tend to get mixed, that is to say that silver and the aluminium are diffusing themselves. The analysis is essentially qualitative with this technique we ca also measure the thickness of thin films, the silver thickness was measured (3320A). (author)

  3. Schiff bases as corrosion inhibitor for aluminium in HCl solution

    International Nuclear Information System (INIS)

    Highlights: ► Three Schiff bases have been tested as possible corrosion inhibitors for aluminium. ► Corrosion tests have been performed via EIS and Tafel polarisation methods. ► Experimental inhibition efficiencies were correlated with quantum chemical parameters. - Abstract: Three Schiff bases named 1,5-bis[2-(2-hydroxybenzylideneamino)phenoxy]-3-oxopentane (D1), 1,5-bis[2-(5-chloro-2-hydroxybenzylideneamino)phenoxy]-3-oxopentane (D2) and 1,5-bis[2-(5-bromo-2-hydroxybenzylideneamino)phenoxy]-3-oxopentane (D3) were synthesized and their inhibitive capabilities on the aluminium corrosion in 0.1 M HCl were investigated by means of electrochemical impedance spectroscopy, Tafel polarisation and scanning electron microscopy techniques. Results showed that, compounds under study exhibit inhibitor properties and adsorption of these compounds was found to accord with Temkin adsorption isotherm. Polarisation curves indicated that the studied Schiff bases were cathodic inhibitor and the effectiveness of these inhibitors decreased in the order of D3 > D2 > D1. Quantum chemical calculations were performed to provide further insight into the inhibition efficiencies determined experimentally.

  4. Experimental study of friction in aluminium bolted joints

    Science.gov (United States)

    Croccolo, D.; de Agostinis, M.; Vincenzi, N.

    2010-06-01

    This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE) method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces) versus sixth tightening (spoiled surfaces). The study considers M8x1.25 8.8 galvanized screws.

  5. Experimental study of aluminium honeycomb behaviour under dynamic multiaxial loading

    Directory of Open Access Journals (Sweden)

    Markiewicz E.

    2012-08-01

    Full Text Available Split Hopkinson Pressure Bar system (SHPB with large-diameter and Nylon bars introducing a shear-compression loading device is used in order to investigate the dynamic behaviour of aluminium honeycomb under multiaxial loadings conditions. All shear-compression configurations including the loading angle variation from 0∘ to 60∘ are performed with an impact velocity of about 15m/s. The adapted SHPB system with the device are validated numerically and a phenomenon of separation between the input bar and the input beveled bar is observed. Numerical results suggest that this phenomenon provides a cutting of the reflected wave. An electro optical extensometer is employed in experiments. A good agreement between the numerical elastic waves and the experimental ones is obtained. Experimental results show a significant effect of the loading angle on the apparent stress-strain curves. The initial peak value and the plateau stress decrease with the increase of the loading angle. The combined shear-compression device with an enhancement at the alignment set-up provides efficient results for samples dynamically loaded. This device will be used to investigate the influence of the in-plane orientation angle on the deformation mechanisms and multiaxial behaviour of aluminium honeycomb under dynamic and quasi-static loading conditions.

  6. High-Rate Compaction of Aluminium Alloy Foams

    International Nuclear Information System (INIS)

    The response of aluminium foams to impact can be categorised according to the impact velocity. Tests have been carried out at a range of impact velocities from quasi-static to velocities approaching the speed of sound in the foam. Various experimental arrangements have been employed including pneumatic launcher tests and plate impact experimants at velocities greater than 1000 m s-1. The quasi-static compression behaviour was approximately elastic, perfectly-plastic, locking. For static and dynamic compression at low impact velocities the deformation pattern was through the cumulative multiplication of discrete, non-contiguous crush bands. Selected impact tests are presented here for which the impact velocity is less than the velocity of sound, but above a certain critical impact velocity so that the plastic compression occurs in a shock-like manner and the specimens deform by progressive cell crushing. Laboratory X-ray microtomography has been employed to acquire tomographic datasets of aluminium foams before and after tests. The morphology of the underformed foam was used as the input dataset to an Eulerian code. Hydrocode simulations were then carried out on a real microstructure. These simulations provide insight to mechanisms associated with the localization of deformation

  7. Graded open-cell aluminium foam core sandwich beams

    International Nuclear Information System (INIS)

    We show that the replication process can be extended towards the production of functionally graded porous structures by fabricating and testing structures in which outer layers of dense metal encase a central part made of foam with graded porosity. Samples of this kind are produced by pressing individual layers of NaCl powder of granulometry 60-90 μm, and then stacking these layers between two skins of dense aluminium. The stacked preforms are then infiltrated with pure aluminium and solidified before dissolution of the salt in water. Specimens containing up to five layers of porous Al of different density between two dense outer skins of pure Al are produced; selected samples are tested in three-point bending. Data show good agreement with analysis based on sandwich beam theory and the Deshpande-Fleck yield criterion. Results of this work indicate that whereas lightweight graded metal/metal foam beams show little promise from the standpoint of stiffness-limited design, they may be of interest from the standpoint of load-limited design

  8. A 3D printed superconducting aluminium microwave cavity

    Science.gov (United States)

    Creedon, Daniel L.; Goryachev, Maxim; Kostylev, Nikita; Sercombe, Timothy B.; Tobar, Michael E.

    2016-07-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals, in particular, has found a number of applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Although many techniques are used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a microwave cavity (resonant frequencies 9.9 and 11.2 GHz) 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable with the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum electrodynamics experiments. The result is achieved even with a very large concentration of non-superconducting silicon in the alloy of 12.18%, compared with Al-6061, which has between 0.4% and 0.8%. Our results may pave the way for the possibility of 3D printing superconducting cavity configurations that are otherwise impossible to machine.

  9. Experimental study of friction in aluminium bolted joints

    Directory of Open Access Journals (Sweden)

    Vincenzi N.

    2010-06-01

    Full Text Available This study aims at developing an experimental tool useful to define accurately the friction coefficients in bolted joints and, therefore, at relating precisely the tightening torque to the bolt preloading force in some special components used in front motorbike suspensions. The components under investigation are some clamped joints made of aluminium alloy. The preloading force is achieved by applying a torque wrench to the bolt head. Some specific specimens have been appropriately designed and realized in order to study the tribological aspects of the tightening phase. Experimental tests have been performed by applying the Design of Experiment (DOE method in order to obtain a mathematical model for the friction coefficients. Three replicas of a full factorial DOE at two levels for each variable have been carried out. The levels include cast versus forged aluminium alloy, anodized versus spray-painted surface, lubricated versus unlubricated screw, and first tightening (fresh unspoiled surfaces versus sixth tightening (spoiled surfaces. The study considers M8x1.25 8.8 galvanized screws.

  10. Modelling of semi-liquid aluminium flow in extrusion

    Directory of Open Access Journals (Sweden)

    G. Skorulski

    2007-04-01

    Full Text Available characterizing by low cost. The significant results may be quickly applying using theory of probability. The way of modelling the deformation mechanisms during extrusion of aluminium alloys in semi - liquid phase, the way of preparing samples and experimental technique has been analysed in the following work. On the ground of received results (i.e. registrations of consecutive process steps the grid of the flow velocity vectors on a flat sample surface was done. It allowed to draw conclusions which one of the basic deformation mechanisms is dominant in particular stage of the process. The technique of measurement has been shown as well. Experiments are made using plasticine and rape oil as a substiute materials. Some kind of different variants have been investigated. To ensure that such model experiments provide useful information it is essential to select model materials and prepare samples that would exhibit (preferably at room temperature similar behaviour and similar deformation mechanisms as those present during the actual deformation process of aluminium alloys in a semi-liquid state. In particular the FLS, SS and PDS mechanisms should be adequately reproduced.

  11. Aluminium surface treatment with ceramic phases using diode laser

    Science.gov (United States)

    Labisz, K.; Tański, T.; Brytan, Z.; Pakieła, W.; Wiśniowski, M.

    2016-07-01

    Ceramic particles powder feeding into surface layer of engineering metal alloy is a well-known and widely used technique. New approach into the topic is to obtain finely distributed nano-sized particles involved in the aluminium matrix using the traditional laser technology. In this paper are presented results of microstructure investigation of cast aluminium-silicon-copper alloys surface layer after heat treatment and alloying with ceramic carbides of WC and ZrO2 using high-power diode laser. The surface layer was specially prepared for the reason of reducing the reflectivity, which is the main problem in the up-to-date metal matrix composites production. With scanning electron microscopy, it was possible to determine the deformation process and distribution of WC and ZrO2 ceramic powder phase. Structure of the surface after laser treatment changes, revealing three zones—remelting zone, heat-affected zone and transition zone placed over the Al substrate. The structural changes of ceramic powder, its distribution and morphology as well as microstructure of the matrix material influence on functional properties, especially wear resistance and hardness of the achieved layer, were investigated.

  12. A 3D Printed Superconducting Aluminium Microwave Cavity

    CERN Document Server

    Creedon, Daniel L; Kostylev, Nikita; Sercombe, Tim; Tobar, Michael E

    2016-01-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals in particular has found a number of novel applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Whilst many techniques can be used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a resonant microwave cavity 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable to the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum...

  13. The determination of boron in aluminium of high purity

    International Nuclear Information System (INIS)

    A description is given of the investigations that led to the development of chemical methods for the determination of boron within the range 0,25 to 1,0 p.p.m. in aluminium of high purity. Methods were developed that incorporated fluorimetry, directly in solutions containing aluminium and after separation of boron by liquid-liquid extraction into 2-ethyl-1,3 hexanediol. A published spectrophotometric method, involving extraction of the BF4sup(-) complex with methylene blue into dichloroethane, was modified for application to alluminium samples. Details of this modified procedure and the fluorimetric-extraction procedure are appended. The precision of the methylene-blue method is about 6 percent relative and is recommended for precision and speed in preference to others. Separation of boron by distillation and spectrophotometric determination with curcumin gave low values in comparison with those obtained by the other methods. Agreement between the boron values obtained on the samples tested was good for the fluorimetric and methylene-blue spectrophotometric methods

  14. Solidification and precipitation in aluminium-zirconium alloys. Pt. 1

    International Nuclear Information System (INIS)

    The cast structure and the precipitating primary phases were investigated in Al-Zr alloys on the basis of high-purity Aluminium with 0.1 to 1.2 wt.% Zr after fast solidification in a watercooled mold. With higher Zr-saturation of the melt the tetragonal ZrAl3-equilibrium phase appears, which is already known from slowly cooled samples. In alloys with lower Zr-supersaturation with respect to the raised Zr-solubility of about 0.6 wt.% due to the fast solidification there appears solely or additionally the new metastable cubic ZrAl3-phase as the primary precipitation. The particles show cubic or fourfold symmetric star form and have nearly the same lattice parameters as Aluminium. By coherent epitaxi of the Al-lattice they act as prefered nuclei for the solidification of the α-phase. Consequently an intensive grain refining takes place in a critical concentration range depending on temperature of pouring and cooling rate. (orig.)

  15. An investigation of coated aluminium bipolar plates for PEMFC

    International Nuclear Information System (INIS)

    Highlights: ► Coated aluminium bipolar plates demonstrate the hydrophobic property than the raw material. ► The corrosion behaviour of bipolar plate decreases the PEMFC performance severely. ► These PEMFCs are measured by current–voltage (I–V) curve test. ► The oxide film increases the interfacial contact resistance. -- Abstract: The performance of Al-alloy bipolar plates for the PEMFC (proton exchange membrane fuel cell) system is investigated in this paper. The metallic bipolar plates are modified with a Ni–P coating. The performance of the Al-alloy bipolar plates is evaluated by the coating structure, corrosion resistance, contact angle and single cell performance. The results indicate that the coated aluminium bipolar plates demonstrate hydrophobic and anti-corrosive properties. The hydrophobic property increases the contact angle on the surface from 46.08° to 80.51°. Meanwhile, the corrosion rate of the Ni–P coating can be over 1 order of magnitude lower than that of the substrate. Hence, the substrate with the coating maintains superior performance under the long term test. The present study proves that both the hydrophobicity and corrosion resistance significantly affect the metallic bipolar plate.

  16. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    Directory of Open Access Journals (Sweden)

    Hamilta de Oliveira Santos

    2005-06-01

    Full Text Available Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken from a billet of an experimental alloy (alloy 1 and were subsequently hot-rolled and cold-rolled (height reduction, 72% and 70%, respectively. The other used samples, alloys 2 and 3, were taken from cylinders liners. The results from the Laue camera showed texture just in the axial direction of alloy 3. The pole figures also indicated the presence of a typical low intensity deformation texture, especially for alloy 3. The spray formed microstructure, which is very fine, hinders the Al-Si texture formation during mechanical work.

  17. Pulsed laser cleaning of aluminium-magnesium alloys: effect of surface modifications on adhesion

    Science.gov (United States)

    Autric, Michel; Oltra, Roland

    2008-05-01

    Surface cleaning is a key step in many industrial processes and especially in laser surface treatments. During laser cleaning of metallic alloys using pulsed lasers, surface modification can be induced due to transient thermal effect. In ambient atmospheric conditions, an oxidation of the cleaned surface can be detected. The aim of this work was to characterize this transient oxidation that can occur below the laser energy domain leading to any phase change (melting, ablation) of the cleaned substrate. A Q-switched Nd:YAG laser (1.06 μm) with 10 ns pulse duration was used for this study. X-ray photoelectron spectroscopy and secondary ion mass spectroscopy were used for surface analysis of irradiated samples. Thermal oxidation took place on the aluminium-magnesium alloy (5000 series) during the irradiation in air (fluence range 0.6-1.4 Jcm-2). It has been demonstrated that this 10 ns laser thermal oxidation and the steady state thermal oxidation have the same mechanism. When the laser fluence reached 1 J cm -2 , the oxide formed by the thermal oxidation became in a large extent crystalline and its outer part was entirely covered by a continuous magnesium oxide layer.

  18. Inhibition of localized attack on the aluminium alloy AA 6351 in glycol/water solutions

    Energy Technology Data Exchange (ETDEWEB)

    Monticelli, C.; Brunoro, G.; Zucchi, F.; Fagioli, F.

    1989-06-01

    The objective of this work was to examine the feasibility of enhancing pitting resistance of AA 6351 (nominal composition: 1% Si, 0.6% Mg, 0.3% Mn, balance Al) by adding suitable inhibitors to the solutions. The compounds used were two inorganic salts: sodium molybdate and sodium tungstate and two derivatives of pyrimidine: 2-aminopyrimidine (2AP) and 2-hydroxypyrimidine (2HP). The inhibiting efficiencies of these substances were tested by both short-time electrochemical tests (galvanic coupling tests and polarization curves) and long-time immersions under experimental conditions causing the localized attack. Molybdate, tungstate and, to some extent, also 2AP efficiently inhibit AA 6351 localized corrosion in degraded solutions at 80/sup 0/C and in pure boiling solutions, for long exposure periods. The short-time electrochemical tests suggest that molybdate and tungstate are able to retard the electrochemical processes occurring on both the aluminium alloy and the small copper cathodic area produced by copper deposition. On the other hand, the 2AP efficiency is attributed to some complexing capability of this pyrimidine derivative towards dissolved copper ions, that are stabilized in solution. 2HP does not prevent AA 6351 localized attack. (orig./MM).

  19. Aluminium fumarate metal-organic framework: A super adsorbent for fluoride from water.

    Science.gov (United States)

    Karmakar, Sankha; Dechnik, Janina; Janiak, Christoph; De, Sirshendu

    2016-02-13

    Potential of aluminium fumarate metal organic framework (MOF) for fluoride removal from groundwater has been explored in this work. The laboratory produced MOF exhibited characteristics similar to the commercial version. MOF was found to be micro-porous with surface area of 1156 m(2)/g and average pore size 17Å. Scanning electron micrograph of the AlFu MOF showed minute pores and texture was completely different from either of the parent materials. Change in the composition of AlFu MOF after fluoride adsorption was evident from powder X-ray diffraction analysis. Thermal stability of the AlFu MOF up to 700K was established by thermo-gravimetric analysis. Incorporation of fluoride phase after adsorption was confirmed by X-ray fluorescence analysis. As observed from FTIR study, hydroxyl ions in AlFu MOF were substituted by fluoride. 0.75 g/l AlFu MOF was good enough for complete removal of 30 mg/l fluoride concentration in feed solution. The maximum adsorption capacity for fluoride was 600, 550, 504 and 431 mg/g, respectively, at 293, 303, 313 and 333K. PMID:26513559

  20. Determination of local material properties of laser beam welded aluminium-steel and aluminium-titanium compounds

    Energy Technology Data Exchange (ETDEWEB)

    Hunkel, M.; Hehl, A. von [IWT Stiftung Institut fuer Werkstofftechnik Bremen (Germany); Barr, A.

    2012-04-15

    The combination of different metallic materials, such as aluminium and steel or aluminium and titanium, by firmly bonding via laser beam welding enables the production of customised hybrid lightweight designs with enhanced properties. Both weld geometry and local material behaviour, which are responsible for the final load characteristics of the compound, are influenced by the process parameters during welding. A novel approach of coupling process, microstructure and mechanical simulation, considering the development of weld geometry and local material conditions is intended to deliver a fast and reliable method for evaluating the quasi-static strength of laser beam welded hybrid compounds. Besides the objective to promote a reduction of expensive welding experiments, the developed method can enhance the performance of hybrid structures as well as their lightweight potential for automotive and aircraft applications. The experimental determination of the local mechanical properties as the basis for the regarded simulation approach is an essential part of a running research project. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)