WorldWideScience

Sample records for aluminium 35

  1. Galvanostatic response of AA2024 aluminium alloy in 3.5% NaCl ...

    Indian Academy of Sciences (India)

    s12034-016-1301-0. Galvanostatic response of AA2024 aluminium alloy in 3.5% NaCl solution. U DONATUS. ∗ and G E THOMPSON. Corrosion and Protection Centre, School of Materials, The University of Manchester, Manchester M13 9PL, UK.

  2. Increased immunogenicity of recombinant Ad35-based malaria vaccine through formulation with aluminium phosphate adjuvant

    NARCIS (Netherlands)

    Ophorst, Olga J. A. E.; Radosevic, Katarina; Klap, Jaco M.; Sijtsma, Jeroen; Gillissen, Gert; Mintardjo, Ratna; van Ooij, Mark J. M.; Holterman, Lennart; Companjen, Arjen; Goudsmit, Jaap; Havenga, Menzo J. E.

    2007-01-01

    Previously, we have shown the potency of recombinant Adenovirus serotype 35 viral vaccines (rAd35) to induce strong immune response against the circumsporozoite protein (CS) of the plasmodium parasite. To further optimize immunogenicity of Ad35-based malaria vaccines we formulated rAd35.CS vaccine

  3. Galvanostatic response of AA2024 aluminium alloy in 3.5% NaCl ...

    Indian Academy of Sciences (India)

    Galvanostatic responses of AA2024T3 alloy in de-aerated and naturally aerated 3.5% NaCl solution have been investigated. In the de-aerated condition, two distinct stages of polarization were revealed. From the first stage, the relationships between the pitting incubation time, pitting potential and applied current density for ...

  4. Galvanostatic response of AA2024 aluminium alloy in 3.5% NaCl ...

    Indian Academy of Sciences (India)

    Abstract. Galvanostatic responses of AA2024T3 alloy in de-aerated and naturally aerated 3.5% NaCl solution have been investigated. In the de-aerated condition, two distinct stages of polarization were revealed. From the first stage, the relationships between the pitting incubation time, pitting potential and applied current ...

  5. Aluminium bridges, aluminium bridge decks

    NARCIS (Netherlands)

    Soetens, F.; Straalen, IJ.J. van

    2003-01-01

    Applications of aluminium have grown considerably in building and civil engineering the last decade. In building and civil engineering the increase of aluminium applications is due to various aspects like light weight, durability and maintenance, use of extrusions, and esthetics. The paper starts

  6. Aluminium in human sweat.

    Science.gov (United States)

    Minshall, Clare; Nadal, Jodie; Exley, Christopher

    2014-01-01

    It is of burgeoning importance that the human body burden of aluminium is understood and is measured. There are surprisingly few data to describe human excretion of systemic aluminium and almost no reliable data which relate to aluminium in sweat. We have measured the aluminium content of sweat in 20 healthy volunteers following mild exercise. The concentration of aluminium ranged from 329 to 5329μg/L. These data equate to a daily excretion of between 234 and 7192μg aluminium and they strongly suggest that perspiration is the major route of excretion of systemic aluminium in humans. Copyright © 2013 Elsevier GmbH. All rights reserved.

  7. Human exposure to aluminium.

    Science.gov (United States)

    Exley, Christopher

    2013-10-01

    Human activities have circumvented the efficient geochemical cycling of aluminium within the lithosphere and therewith opened a door, which was previously only ajar, onto the biotic cycle to instigate and promote the accumulation of aluminium in biota and especially humans. Neither these relatively recent activities nor the entry of aluminium into the living cycle are showing any signs of abating and it is thus now imperative that we understand as fully as possible how humans are exposed to aluminium and the future consequences of a burgeoning exposure and body burden. The aluminium age is upon us and there is now an urgent need to understand how to live safely and effectively with aluminium.

  8. Rows of Dislocation Loops in Aluminium Irradiated by Aluminium Ions

    DEFF Research Database (Denmark)

    Henriksen, L.; Johansen, A.; Koch, J.

    1967-01-01

    Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along <110 > directions. ©1967 The American Institute of Physics......Single-crystal aluminium specimens, irradiated with 50-keV aluminium ions, contain dislocation loops that are arranged in regular rows along directions. ©1967 The American Institute of Physics...

  9. Phosphorus enhances aluminium tolerance in both aluminium ...

    African Journals Online (AJOL)

    Seedlings growing in acid soils suffer both phosphorus (P) deficiency and aluminium (Al) toxicity stresses. An experiment was conducted to study the effects of Al and P interaction on Al-tolerant (ET8) and Al-sensitive (ES8) wheat genotypes in an acid soil. This study aimed to determine the interactive effect of Al and P in soil ...

  10. Aluminium-rich corner in Al-Cu-La system

    International Nuclear Information System (INIS)

    Yunusov, I.; Ganiev, I.N.

    1990-01-01

    Aluminium corner of Al-Cu-La system are investigated by means of microstructural and differential thermal analysis. Existence of LaCu 2 Al 10 and LaCu 0.5 Al 3.5 ternary compounds in the system is confirmed and it is shown, as well, both compounds are in two-phase equilibrium with aluminium solid solution and form with it and between each other eutectic type state diagrams. State diagrams for quasibinary sections are plotted

  11. Ion nitriding of aluminium

    International Nuclear Information System (INIS)

    Fitz, T.

    2002-09-01

    The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma immersion ion implantation, which are methods with a potential for industrial application. (orig.)

  12. Method for aluminium dross utilization

    International Nuclear Information System (INIS)

    Lucheva, B.; Petkov, R.; Tzonev, Tz.

    2003-01-01

    A new hydrometallurgical method has been developed for metal aluminum utilization from secondary aluminum dross. Secondary aluminum dross is a powder product with an average of 35% aluminium content (below 1mm). It is waste from primary aluminum dross pyrometallurgical flux less treatment in rotary DC electric arc furnace. This method is based on aluminum leaching in copper chloride water solution. As a result an aluminum oxychloride solution and solids, consisting of copper and oxides are obtained. In order to copper chloride solution regenerate hydrochloric acid is added to the solids. The process is simple, quick, economic and safe. The aluminum oxychloride solution contains 56 g/l Al 2 O 3 . The molar ratios are Al:Cl=0,5; OH:Al=1. The solution has 32 % basicity and 1,1 g/cm 3 density. For increasing the molar ratio of aluminium to chlorine aluminum hydroxide is added to this solution at 80 o C. Aluminum hydroxide is the final product from the secondary aluminum dross alkaline leaching. As a result aluminum oxychloride solution of the following composition is prepared: Al 2 O 3 - 180 g/l; Al:Cl=1,88; OH:Al=4,64; basicity 82%; density 1,22 g/cm 3 , pH=4 -4,5. Aluminum oxychloride solution produced by means of this method can be used in potable and wastewater treatment, paper making, in refractory mixture as a binder etc. (Original)

  13. Aluminium in Fisch und Fischereierzeugnissen

    OpenAIRE

    Ranau, Reiner; Oehlenschläger, Jörg

    1997-01-01

    Recent reports associating aluminium with several skeletal (osteomalacia) and neurological disorders (encephalopathy and Alzheimer’s disease) in humans suggest that exposure to aluminium may pose a hazard to health. This requires the examination of aluminiumcontent in different foodstuffs. Therefore, an analytical method for the determination of aluminium in fish and fishery products, especially in fishery products packaged in aluminium cans, was developed using graphite furnace atomic absorp...

  14. Recovery in aluminium

    DEFF Research Database (Denmark)

    Gundlach, Carsten

    2006-01-01

    In the present thesis the development of a unique experimental method for volume characterisation of individual embedded crystallites down to a radius of 150 nm is presented. This method is applied to in-situ studies of recovery in aluminium. The method is an extension of 3DXRD microscopy, an X...... by the combined use of X-ray micro focusing optics, new scanning algorithms and the use of foils. The ratio of foil thickness to crystallite size should be at least 10 such that the central ones are situated in a bulk environment. To avoid thermal drifts, gold reference markers are deposited onto the sample...... are represented as strings. To identify the strings a combination of a 5D connected component type algorithm and multi-peak fitting was found to be superior. The first use of the method was a study of recovery of a deformed aluminium alloy (AA1050). The aluminium alloy was deformed by cold rolling to a thickness...

  15. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.; Soetens, F.

    2005-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical

  16. Fire exposed aluminium structures

    NARCIS (Netherlands)

    Maljaars, J.; Fellinger, J.H.H.; Soetens, F.

    2006-01-01

    Material properties and mechanical response models for fire design of steel structures are based on extensive research and experience. Contrarily, the behaviour of aluminium load bearing structures exposed to fire is relatively unexplored. This article gives an overview of physical and mechanical

  17. Activation Analysis of Aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Brune, Dag

    1961-01-15

    An analysis of pure aluminium alloyed with magnesium was per- formed by means of gamma spectrometry , Chemical separations were not employed. The isotopes to be determined were obtained in conditions of optimum activity by suitably choosing the time of irradiation and decay. The following elements were detected and measured quantitatively: Iron, zinc, copper, gallium, manganese, chromium, scandium and hafnium.

  18. Roll bonding of strained aluminium

    DEFF Research Database (Denmark)

    Staun, Jakob M.

    2003-01-01

    This report investigates roll bonding of pre-strained (å ~ 4) aluminium sheets to produce high strain material from high purity aluminium (99.996%) and commercial pure aluminium (99.6%). The degree of bonding is investigated by optical microscopy and ultrasonic scanning. Under the right...... of the cross rolled volume fraction is found. To further asses this effect, and the anisotropy, it is necessary to acquire knowledge about both texture and microstructure, e.g. by TEM. Roll bonding of pre-strained aluminium is found to be a possible alternative to ARB in the quest for ultra-fine grained...

  19. Fatigue tests on aluminium bridges

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Traffic bridges are subjected to variable loads and should therefore be checked on fatigue. Especially low weight materials, like aluminium, are sensitive to fatigue, because the variable load is a substantial part of the total load. This paper shows the structural design of an aluminium bridge

  20. Advanced shipbuilding in aluminium

    International Nuclear Information System (INIS)

    Larsson, H.; Svensson, L.E.; Karlsson, L.

    1997-01-01

    The applicability of two different welding techniques for welding ships in aluminium is discussed. Conventional MIG welding and the recently developed Friction Super Stir Welding (FSSW) are compared concerning weld metal microstructures and mechanical properties. Results from testing of FSSW welds are also presented. It was observed that the grain size was smaller in FSSW welds are also presented. It was observed that the grain size was smaller in FSSW welds than in MIG welds whereas precipitates generally were larger in FSSW welds. The two methods produced welds with comparable mechanical properties. Good fatigue behaviour was obtained for FSSW welds. Advantages of the welding methods are also discussed. (Author) 7 refs

  1. Aluminium in Drinkwater: voorkomen, herkomst en gezondheidsaspecten

    NARCIS (Netherlands)

    Versteegh JFM; de Boer JLM; van den Velde-Koerts T

    1992-01-01

    Aluminium can occur in drinking water because of the application of aluminium salts as a coagulant in the treatment of drinking water. In the Netherlands mostly iron salts are used instead of aluminium. Besides this aluminium can be present in the source for drinking water. In shallow groundwater

  2. Aluminium toxicity in winter wheat

    Directory of Open Access Journals (Sweden)

    Szabó A.

    2015-01-01

    Full Text Available Aluminium is the most frequent metal of the earth crust; it occurs mainly as biologically inactive, insoluble deposit. Environmental problems, industrial contaminations and acid rains increase the soil acidity, leading to the mobilization of Al. Half of the world’s potential arable lands are acidic; therefore, Al-toxicity decreases crop productivity. Wheat is a staple food for 35% of the world population. The effects of Al-stress (0.1 mM were studied on winter wheat; seedlings were grown hydroponically, at acidic pH. After two weeks, the root weight was decreased; a significant difference was found in the P- and Ca-content. The shoot weight and element content changed slightly; Al-content in the root was one magnitude higher than in the shoot, while Al-translocation was limited. The root plasma membrane H+-ATPase has central role in the uptake processes; Al-stress increased the Mg2+-ATPase activity of the microsomal fraction.

  3. Direct electrodeposition of aluminium nano-rods

    OpenAIRE

    Perre, Emilie; Nyholm, Leif; Gustafsson, Torbjörn; Taberna, Pierre-Louis; Simon, Patrice; Edström, Kristina

    2008-01-01

    Electrodeposition of aluminium within an alumina nano-structured template, for use as high surface area current collectors in Li-ion microbatteries, was investigated. The aluminium electrodeposition was carried out in the ionic liquid 1-ethyl-3-methylimidazolium chloride:aluminium chloride (1:2 ratio). First the aluminium electrodeposition process was confirmed by combined cyclic voltammetry and electrochemical quartz crystal microbalance measurements. Then, aluminium was electrodeposit...

  4. Aluminium in Drinkwater: voorkomen, herkomst en gezondheidsaspecten

    OpenAIRE

    Versteegh JFM; de Boer JLM; van den Velde-Koerts T

    1992-01-01

    Aluminium can occur in drinking water because of the application of aluminium salts as a coagulant in the treatment of drinking water. In the Netherlands mostly iron salts are used instead of aluminium. Besides this aluminium can be present in the source for drinking water. In shallow groundwater high levels have been found probably related to acidification, which is an environmental problem. Aluminium can cause neurological diseases in patients who are on chronic haemodialysis because of ren...

  5. Alloys of uranium and aluminium with low aluminium content

    International Nuclear Information System (INIS)

    Cabane, G.; Englander, M.; Lehmann, J.

    1955-01-01

    Uranium, as obtained after spinning in phase γ, presents an heterogeneous structure with large size grains. The anisotropic structure of the metal leads to an important buckling and surface distortion of the fuel slug which is incompatible with its tubular cladding for nuclear fuel uses. Different treatments have been made to obtain an isotropic structure presenting high thermal stability (laminating, hammering and spinning in phase α) without success. Alloys of uranium and aluminium with low aluminium content present important advantage in respect of non allied uranium. The introduction of aluminium in the form of intermetallic compound (UAl 2 ) gives a better resistance to thermal fatigue. Alloys obtained from raw casting present an improved buckling and surface distortion in respect of pure uranium. This improvement is obtained with uranium containing between 0,15 and 0,5 % of aluminium. An even more improvement in thermal stability is obtained by thermal treatments of these alloys. These new characteristics are explained by the fine dispersion of the UAl 2 particles in uranium. The results after treatments obtained from an alloy slug containing 0,4 % of aluminium show no buckling or surface distortion and no elongation. (M.P.)

  6. Effect of hydrogen on aluminium and aluminium alloys: A review

    DEFF Research Database (Denmark)

    Ambat, Rajan; Dwarakadasa, E.S.

    1996-01-01

    Susceptibility of aluminium and its alloys towards hydrogen embrittlement has been well established. Still a lot of confusion exists on the question of transport of hydrogen and its possible role in stress corrosion cracking. This paper reviews some of the fundamental properties of hydrogen...... in aluminium and its alloys and its effect on mechanical properties. The importance of hydrogen embrittlement over anodic dissolution to explain the stress corrosion cracking mechanism of these alloys is also examined in considerable detail. The various experimental findings concerning the link between...... hydrogen embrittlement and stress corrosion cracking are also discussed....

  7. Design and analysis of aluminium brdiges

    NARCIS (Netherlands)

    Soetens, F.; Straalen, IJ.J. van

    2004-01-01

    Applications of aluminium have grown considerably in building and civil engineering the last decade, which is due to various aspects: light weight, durability and maintenance, use of extrusions. The paper starts with a short history of aluminium bridges and then focuses on aluminium bridges in the

  8. Buckwheat stomatal traits under aluminium toxicity

    Directory of Open Access Journals (Sweden)

    Oleksandr E. Smirnov

    2014-04-01

    Full Text Available Aluminium influence on some stomatal parameters of common buckwheat (Fagopyrum esculentum Moench. was studied. Significant changes in stomatal density, stomatal index and stomatal shape coefficient under aluminium treatment were revealed. Stomatal closure and no difference in total stomatal potential conductance index of treatment plants were suggested as aluminium resistance characteristics.

  9. Does Aluminium Trigger Breast Cancer?

    Directory of Open Access Journals (Sweden)

    Peter Jennrich

    2016-08-01

    Full Text Available Summary. Breast cancer is by far the most common cancer in women in the western world. In 90% of breast cancers, environmental factors are among the causes. The frequency with which the tumour occurs in the outer upper part of the breast has risen with above average rates in recent decades. Aluminium salts as ingredients in deodorants and antiperspirants are being absorbed by the body to a greater extent than hitherto assumed. Their toxicity for healthy and diseased breast tissue cells includes various well-documented pathomechanisms. In the sense of primary and secondary prevention, the cancer-triggering potential of aluminium and its use in anti-perspirant deodorants must be re-evaluated. For the same reason the access to a targeted diagnosis and treatment of aluminium loading must be facilitated.

  10. Aluminium phosphide-induced leukopenia.

    Science.gov (United States)

    Ntelios, Dimitrios; Mandros, Charalampos; Potolidis, Evangelos; Fanourgiakis, Panagiotis

    2013-10-30

    Acute intoxication from the pesticide aluminium phosphide is a relatively rare, life-threatening condition in which cardiovascular decompensation is the most feared problem. We report the case of a patient exposed to aluminium phosphide-liberated phosphine gas. It resulted in the development of a gastroenteritis-like syndrome accompanied by severe reduction in white blood cell numbers as an early and prominent manifestation. By affecting important physiological processes such as mitochondrial function and reactive oxygen species homeostasis, phosphine could cause severe toxicity. After presenting the characteristics of certain leucocyte subpopulations we provide the current molecular understanding of the observed leukopenia which in part seems paradoxical.

  11. Effect of Bio char on Plant Growth and Aluminium Form of Soil under Aluminium Stress

    Science.gov (United States)

    Qian, Lianwen; Li, Qingbiao; Sun, Jingwei; Feng, Ying

    2018-01-01

    Aluminium-enriched acid red soils in South China easily cause aluminium toxicity to plants, but biochip can improve soils and eliminate soil contaminations. In this project, biochip was used in potted plant control test to study the effect of biochip on plant growth in soil under acid aluminium stress and the migration and conversion of aluminium in plant-soil system. The fin dings show that the application of biochip increases the pH value of soil under aluminium stress significantly, changes the existing form of aluminium ion in soil, reduces the plants’ absorption of aluminium, and alleviates the aluminium toxicity to plants, but too much biochip may inhibit the growth of plants. In this case, further study should be carried out as regards the volume and way of biochip input in practical applications as well as the timeliness of aluminium toxicity removal.

  12. Constitutive modelling of aluminium foams

    NARCIS (Netherlands)

    Wang, W.M.; Lemmen, P.P.M.

    2001-01-01

    In this paper an aluminium foam model is proposed for a vehicle crash analysis. The model assumes that there is no coupling between stresses and strains in different principal directions. The stress in each principle direction is then interpolated from an experimental recorded uniaxial stress strain

  13. Recovery mechanisms in nanostructured aluminium

    DEFF Research Database (Denmark)

    Yu, Tianbo; Hansen, Niels; Huang, Xiaoxu

    2012-01-01

    Commercial purity aluminium (99.5%) has been cold rolled to a true strain of 5.5 (99.6% reduction in thickness). The material is very strong but low temperature recovery may be a limiting factor. This has been investigated by isothermal annealing treatments in the temperature range 5–100C. Hardness...

  14. Decomposition of oxidezed lead and aluminium thin films on molybdenum substrates

    International Nuclear Information System (INIS)

    Makarovskij, N.A.

    1981-01-01

    The decomposition of oxidized solid phase lead and aluminium thin films on molybdenum substrates in the process of diffusion annealing in the 5x10 -5 mm Hg vacuum at temperatures from 280 to 320 deg C and from 500 to 560 deg C, respectively, is investigated. The conclusion is made that failure of oxidized lead and aluminium thin film coatings is carried out by the mechanism of volumetric self-diffusion. Experimentally established values of activation energies of the process of lead (Qsub(Mo)sup(Pb)=29 kcal/mol) and aluminium (Qsub(Mo)sup(Al)=35 kcal/mol) film failure are close to corresponding activation energies of lead and aluminium volumetric self-diffusion, which agrees with the conclusions made [ru

  15. Bumblebee pupae contain high levels of aluminium.

    Science.gov (United States)

    Exley, Christopher; Rotheray, Ellen; Goulson, David

    2015-01-01

    The causes of declines in bees and other pollinators remains an on-going debate. While recent attention has focussed upon pesticides, other environmental pollutants have largely been ignored. Aluminium is the most significant environmental contaminant of recent times and we speculated that it could be a factor in pollinator decline. Herein we have measured the content of aluminium in bumblebee pupae taken from naturally foraging colonies in the UK. Individual pupae were acid-digested in a microwave oven and their aluminium content determined using transversely heated graphite furnace atomic absorption spectrometry. Pupae were heavily contaminated with aluminium giving values between 13.4 and 193.4 μg/g dry wt. and a mean (SD) value of 51.0 (33.0) μg/g dry wt. for the 72 pupae tested. Mean aluminium content was shown to be a significant negative predictor of average pupal weight in colonies. While no other statistically significant relationships were found relating aluminium to bee or colony health, the actual content of aluminium in pupae are extremely high and demonstrate significant exposure to aluminium. Bees rely heavily on cognitive function and aluminium is a known neurotoxin with links, for example, to Alzheimer's disease in humans. The significant contamination of bumblebee pupae by aluminium raises the intriguing spectre of cognitive dysfunction playing a role in their population decline.

  16. Friction Welding of Aluminium and Aluminium Alloys with Steel

    Directory of Open Access Journals (Sweden)

    Andrzej Ambroziak

    2014-01-01

    Full Text Available The paper presents our actual knowledge and experience in joining dissimilar materials with the use of friction welding method. The joints of aluminium and aluminium alloys with the different types of steel were studied. The structural effects occurring during the welding process were described. The mechanical properties using, for example, (i microhardness measurements, (ii tensile tests, (iii bending tests, and (iv shearing tests were determined. In order to obtain high-quality joints the influence of different configurations of the process such as (i changing the geometry of bonding surface, (ii using the interlayer, or (iii heat treatment was analyzed. Finally, the issues related to the selection of optimal parameters of friction welding process were also investigated.

  17. Partial molar volumes of aluminium chloride, aluminium sulphate and aluminium nitrate in water-rich binary aqueous mixtures of tetrahydrofuran

    OpenAIRE

    R. C. Thakur; Ravi Sharma; Ashish Kumar; Sanjay Kumar; M. L. Parmar

    2014-01-01

    Partial molar volumes of aluminium chloride, aluminium sulphate and aluminium nitrate have been determined in water rich binary aqueous mixtures of tetrahydrofuran (5, 10, 15, 20% by weight of tetrahydrofuran) with the help of density measurements. The density measurements were made by using Ward and Millero method and results have been analysed by Masson’s equation and interpreted in terms of ion-ion or ion –solvent interactions. The partial molar volumes vary with temperature as a power ser...

  18. PREPARATION AND PROPERTIES OF ALUMINIUM COMPOSITE

    OpenAIRE

    T. Albert*, C. Pravin Tamil Selvan

    2017-01-01

    A composite material is the combination of two or more materials, which are having different phases and the properties superior to the base material. Aluminium matrix composite (AMCs) are emerging as advance engineering materials due to their strength, ductility and toughness. The aluminium matrix can strengthened by reinforcing with hard ceramic particles like SiC, Al2o3 , B4C etc. In this paper, an effort is made to enhance the mechanical properties like strength and hardness of aluminium ...

  19. Surface treatments for aluminium alloys

    Science.gov (United States)

    Ardelean, M.; Lascău, S.; Ardelean, E.; Josan, A.

    2018-01-01

    Typically, in contact with the atmosphere, the aluminium surface is covered with an aluminium oxide layer, with a thickness of less than 1-2μm. Due to its low thickness, high porosity and low mechanical strength, this layer does not protect the metal from corrosion. Anodizing for protective and decorative purposes is the most common method of superficial oxidation processes and is carried out through anodic oxidation. The oxide films, resulted from anodizing, are porous, have a thickness of 20-50μm, and are heat-resistant, stable to water vapour and other corrosion agents. Hard anodizing complies with the same obtains principles as well as decorative and protective anodization. The difference is in that hard anodizing is achieved at low temperatures and high intensity of electric current. In the paper are presented the results of decorative and hard anodization for specimens made from several aluminium alloys in terms of the appearance of the specimens and of the thickness of the anodized.

  20. A biogeochemical cycle for aluminium?

    Science.gov (United States)

    Exley, Christopher

    2003-09-15

    The elaboration of biogeochemical cycles for elements which are known to be essential for life has enabled a broad appreciation of the homeostatic mechanisms which underlie element essentiality. In particular they can be used effectively to identify any part played by human activities in element cycling and to predict how such activities might impact upon the lithospheric and biospheric availability of an element in the future. The same criteria were the driving force behind the construction of a biogeochemical cycle for aluminium, a non-essential element which is a known ecotoxicant and a suspected health risk in humans. The purpose of this exercise was to examine the concept of a biogeochemical cycle for aluminium and not to review the biogeochemistry of this element. The cycle as presented is rudimentary and qualitative though, even in this nascent form, it is informative and predictive and, for these reasons alone, it is deserving of future quantification. A fully fledged biogeochemical cycle for aluminium should explain the biospheric abundance of this element and whether we should expect its (continued) active involvement in biochemical evolution.

  1. Toxicity of aluminium on five aquatic invertebrates; Aluminiums toksisitet paa 5 akvatiske invertebrater

    Energy Technology Data Exchange (ETDEWEB)

    Moe, J. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper deals with the experiments done by investigating the effects from the toxicity of aluminium on aquatic invertebrates. The aim of the experiments was to compare the toxicity of unstable aluminium compounds with stable forms of aluminium. 8 refs., 2 figs., 2 tabs.

  2. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... micrograms/l to 77 micrograms/l. Examination of the aluminium and nickel contents of the constituents for the production of one brand showed too low levels to explain the final contamination of the product. By following the aluminium and nickel concentrations of the same brand during the production...

  3. Aluminium and nickel in human albumin solutions

    DEFF Research Database (Denmark)

    Gammelgaard, Bente; Sandberg, E

    1989-01-01

    Five different brands of commercially available human albumin solutions for infusion were analysed for their aluminium and nickel contents by atomic absorption spectrometry. The aluminium concentrations ranged from 12 micrograms/l to 1109 micrograms/l and the nickel concentrations ranged from 17...... of a batch of albumin solution, filtration was shown to contribute to contamination, although the largest increase in aluminium as well as nickel concentrations appeared during the bulk concentrating process. To avoid health risks to certain patients, regulations should be established requiring aluminium...

  4. Aluminium in apple juice - no storing of fruit juice in aluminium tanks

    OpenAIRE

    German Federal Institute for Risk Assessment

    2017-01-01

    Elevated aluminium levels in fruit juice, particularly in apple juice, were measured by the official food control authorities. The cause was the incorrect storage of juice in aluminium containers that were not coated with varnish. As aluminium is dissolved by acid-containing and salt-containing food, the metal was able to migrate to the juice. In the case of short-term dietary intake, aluminium is scarcely harmful at all. In the case of elevated, long-term intake, aluminium can, howe...

  5. Do oral aluminium phosphate binders cause accumulation of aluminium to toxic levels?

    Directory of Open Access Journals (Sweden)

    Roberts Norman B

    2011-10-01

    Full Text Available Abstract Background Aluminium (Al toxicity was frequent in the 1980s in patients ingesting Al containing phosphate binders (Alucaps whilst having HD using water potentially contaminated with Al. The aim of this study was to determine the risk of Al toxicity in HD patients receiving Alucaps but never exposed to contaminated dialysate water. Methods HD patients only treated with Reverse Osmosis(RO treated dialysis water with either current or past exposure to Alucaps were given standardised DFO tests. Post-DFO serum Al level > 3.0 μmol/L was defined to indicate toxic loads based on previous bone biopsy studies. Results 39 patients (34 anuric were studied. Mean dose of Alucap was 3.5 capsules/d over 23.0 months. Pre-DFO Al levels were > 1.0 μmol/L in only 2 patients and none were > 3.0 μmol/L. No patients had a post DFO Al levels > 3.0 μmol/L. There were no correlations between the serum Al concentrations (pre-, post- or the incremental rise after DFO administration and the total amount of Al ingested. No patients had unexplained EPO resistance or biochemical evidence of adynamic bone. Conclusions Although this is a small study, oral aluminium exposure was considerable. Yet no patients undergoing HD with RO treated water had evidence of Al toxicity despite doses equivalent to 3.5 capsules of Alucap for 2 years. The relationship between the DFO-Al results and the total amount of Al ingested was weak (R2 = 0.07 and not statistically significant. In an era of financial prudence, and in view of the recognised risk of excess calcium loading in dialysis patients, perhaps we should re-evaluate the risk of using Al-based phosphate binders in HD patients who remain uric.

  6. Aluminium Pneumoconiosis I. In Vitro Comparison of Stamped Aluminium Powders Containing Different Lubricating Agents and a Granular Aluminium Powder

    Science.gov (United States)

    Corrin, B.

    1963-01-01

    The discrepancy in previous reports of the action of aluminium on the lung may be explained by differences between stamped and granular aluminium powders. A stamped powder of the variety causing pulmonary fibrosis showed a brisk reaction with water, but a granular powder was unreactive. This difference is primarily due to the granular particles being covered by inert aluminium oxide, the formation of which is partially prevented in the stamping process by stearine and mineral oil. The reactivity of the flake-like stamped particles is also dependent on their large surface area per unit volume. The appearance of aluminium pneumoconiosis in Britain is explained by the introduction of mineral oil into the stamping industry for, in contrast to stearine, mineral oil permits the powder to react with water. The lung damage is believed to be caused by a soluble form of aluminium. PMID:14072616

  7. Rapidly solidified aluminium for optical applications

    NARCIS (Netherlands)

    Gubbels, G.P.H.; Venrooy, B.W.H. van; Bosch, A.J.; Senden, R.

    2008-01-01

    This paper present the results of a diamond turning study of a rapidly solidified aluminium 6061 alloy grade, known as RSA6061. It is shown that this small grain material can be diamond turned to smaller roughness values than standard AA6061 aluminium grades. Also, the results are nearly as good as

  8. Electron Conditioning of Technical Aluminium Surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Le Pimpec, F

    2004-09-02

    The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (= 1.3, value of many pure elements [1]), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

  9. Thermal formation of corundum from aluminium hydroxides ...

    Indian Academy of Sciences (India)

    Abstract. Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form γ-Al2O3 at ~ 400°C but the formation of α-Al2O3 at 1200°C occurs more readily in the material ...

  10. Thermal formation of corundum from aluminium hydroxides ...

    Indian Academy of Sciences (India)

    Aluminium hydroxides have been precipitated from various aluminium salts and the differences in their thermal behaviour have been investigated. Pseudoboehmite derived from the nitrate, sulfate and chloride all form -Al2O3 at ∼ 400°C but the formation of -Al2O3 at 1200°C occurs more readily in the material derived ...

  11. Characterisation and concentration profile of aluminium during ...

    African Journals Online (AJOL)

    An aluminium(Al) characterisation study was conducted at a surface water treatment plant (Buffalo Pound Water Treatment Plant (BPWTP) in Moose Jaw, Saskatchewan, Canada) to understand better the effect of alum coagulant on various Al fractions. The raw water source for BPWTP is Buffalo Pound Lake water. The Al ...

  12. Lactobacillus plantarum CCFM639 alleviates aluminium toxicity.

    Science.gov (United States)

    Yu, Leilei; Zhai, Qixiao; Liu, Xiaoming; Wang, Gang; Zhang, Qiuxiang; Zhao, Jianxin; Narbad, Arjan; Zhang, Hao; Tian, Fengwei; Chen, Wei

    2016-02-01

    Aluminium (Al) is the most abundant metal in the earth's crust. Al exposure can cause a variety of adverse physiological effects in humans and animals. Our aim was to demonstrate that specific probiotic bacteria can play a special physiologically functional role in protection against Al toxicity in mice. Thirty strains of lactic acid bacteria (LAB) were tested for their aluminium-binding ability, aluminium tolerance, their antioxidative capacity, and their ability to survive the exposure to artificial gastrointestinal (GI) juices. Lactobacillus plantarum CCFM639 was selected for animal experiments because of its excellent performance in vitro. Forty mice were divided into four groups: control, Al only, Al plus CCFM639, and Al plus deferiprone (DFP). CCFM639 was administered at 10(9) CFU once daily for 10 days, followed by a single oral dose of aluminium chloride hexahydrate at 5.14 mg aluminium (LD50) for each mouse. The results showed that CCFM639 treatment led to a significant reduction in the mortality rates with corresponding decrease in intestinal aluminium absorption and in accumulation of aluminium in the tissues and amelioration of hepatic histopathological damage. This probiotic treatment also resulted in alleviation of hepatic, renal, and cerebral oxidative stress. The treatment of L. plantarum CCFM639 has potential as a therapeutic dietary strategy against acute aluminium toxicity.

  13. Behaviour of millscale reinforced Aluminium Bronze composite ...

    African Journals Online (AJOL)

    Despite the desirable characteristics exhibited by most aluminium bronze, the deficient responses in certain critical applications have necessitated improvement in the mechanical properties. The microstructural and mechanical properties of cast aluminium bronze reinforced with iron millscale particles were investigated in ...

  14. Acoustic properties of aluminium foams

    Directory of Open Access Journals (Sweden)

    García, L. E.

    2008-09-01

    Full Text Available The article discusses normal incidence sound absorption by aluminium foam manufactured with powder metallurgy technology. Aluminium foams with different surface morphologies were obtained by varying the type of precursor and adding filler materials during the foaming process. The sound absorption coefficients found for these aluminium foams were compared to the coefficient for commercial foams marketed under the name ALPORAS. The effect of foam thickness on the absorption coefficient was studied for each sample prepared. The combination of good acoustic and mechanical properties makes aluminium foams particularly attractive products. The study included an analysis of the effect of 2-, 5- and 10-cm air gaps on the sound absorption coefficient. The results showed that such gaps, which are routinely used in construction to reduce the reverberation period in indoor premises, raised the low frequency absorption coefficient significantly. This increase was found to depend on aluminium foam density and thickness and the depth of the air gap. In this same line, we have investigated the absorption coefficient of the aluminium foams combined with a mineral fiber panel.Se presenta un estudio del coeficiente de absorción acústica a incidencia normal de espumas de aluminio fabricadas mediante la técnica pulvimetalúrgica. Se fabricaron espumas de aluminio de distinta morfología superficial variando el tipo de precursor y usando materiales de relleno durante el proceso de espumación. Se muestra un estudio comparativo del coeficiente de absorción acústica de las espumas de aluminio fabricadas y las espumas comerciales conocidas como ALPORAS. Para cada muestra fabricada se estudió la influencia del espesor sobre el valor del coeficiente de absorción.El atractivo de las espumas de aluminio radica en que en ellas se combinan interesantes propiedades acústicas y mecánicas. Se analizó el efecto de una cámara de aire de 2, 5 y 10 cm de anchura sobre el

  15. Corrosion behaviour of laser-cleaned AA7024 aluminium alloy

    Science.gov (United States)

    Zhang, F. D.; Liu, H.; Suebka, C.; Liu, Y. X.; Liu, Z.; Guo, W.; Cheng, Y. M.; Zhang, S. L.; Li, L.

    2018-03-01

    Laser cleaning has been considered as a promising technique for the preparation of aluminium alloy surfaces prior to joining and welding and has been practically used in the automotive industry. The process is based on laser ablation to remove surface contaminations and aluminium oxides. However the change of surface chemistry and oxide status may affect corrosion behaviour of aluminium alloys. Until now, no work has been reported on the corrosion characteristics of laser cleaned metallic surfaces. In this study, we investigated the corrosion behaviour of laser-cleaned AA7024-T4 aluminium alloy using potentiodynamic polarisation, electrochemical impedance spectroscopy (EIS) and scanning vibrating electrode technique (SVET). The results showed that the laser-cleaned surface exhibited higher corrosion resistance in 3.5 wt.% NaCl solution than as-received hot-rolled alloy, with significant increase in impedance and decrease in capacitance, while SVET revealed that the active anodic points appeared on the as-received surface were not presented on the laser-cleaned surfaces. Such corrosion behaviours were correlated to the change of surface oxide status measured by glow discharge optical emission spectrometry (GDOES) and X-ray photoelectron spectroscopy (XPS). It was suggested that the removal of the original less protective oxide layer consisting of MgO and MgAl2O4 on the as-received surfaces and the newly formed more protective oxide layer containing mainly Al2O3 and MgO by laser cleaning were responsible for the improvement of the corrosion performance.

  16. Intermetallic particles-induced pitting corrosion in 6061-T651 aluminium alloy

    CSIR Research Space (South Africa)

    Mutombo, K

    2011-07-01

    Full Text Available The polished 6061-T651 aluminium alloy was immersed in 3.5% NaCl solution with about 7 ppm dissolved oxygen. Scanning Electron Microscopy equipped with Energy dispersive Xray Spectroscopy revealed the presence of Al-Si-Fe-containing particles...

  17. Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance

    CSIR Research Space (South Africa)

    Nath, S

    2012-03-01

    Full Text Available In the present study, laser surfac ealloying of aluminium with WC + Co + NiCr (in the ratio of 70:15:15) has been conducted using a 5 kW continuous wave (CW) Nd:YAG laser (at a beam diameter of 0.003 m), with the output power ranging from 3 to 3.5 k...

  18. Laser surface alloying of aluminium with WC+Co+NiCr for improved wear resistance

    CSIR Research Space (South Africa)

    Nath, S

    2012-03-01

    Full Text Available In the present study, laser surface alloying of aluminium with WC + Co + NiCr (in the ratio of 70:15:15) has been conducted using a 5 kW continuous wave (CW) Nd:YAG laser (at a beam diameter of 0.003 m), with the output power ranging from 3 to 3.5 k...

  19. Aluminium in foodstuff and the influence of aluminium foil used for food preparation or short time storage.

    Science.gov (United States)

    Ertl, Kathrin; Goessler, Walter

    2018-02-28

    Aluminium is an omnipresent part of everyday life. It is widely used in industry and furthermore in products like cosmetics, sun creams or it can be applied for instance as aluminium foil by consumers during food preparation in households. However, over the last decades the toxicity of aluminium for humans has been heavily discussed and is still not completely clarified. Therefore, food aluminium concentrations were investigated in different untreated foodstuff as well as a possible aluminium transfer from aluminium foil to food. The results show that untreated food is not significantly contaminated. Furthermore, short time contact to aluminium foil increases the food aluminium concentration only marginal. Nevertheless, as soon as the food is in contact to aluminium foil and at the same time in contact with metals (alloys) with a higher standard electrode potential than aluminium (-1.66 V) high aluminium contaminations were observed.

  20. Recent developments in advanced aircraft aluminium alloys

    International Nuclear Information System (INIS)

    Dursun, Tolga; Soutis, Costas

    2014-01-01

    Highlights: • To compete with composites, performance of aluminium alloys should be increased. • Al–Li alloys have higher strength, fracture and fatigue/corrosion resistance. • Improvements of aerospace Al alloys are due to optimised solute content and ratios. • In selecting new materials, there should be no reduction in the level of safety. • The use of hybrid materials could provide additional opportunities for Al alloys. - Abstract: Aluminium alloys have been the primary material for the structural parts of aircraft for more than 80 years because of their well known performance, well established design methods, manufacturing and reliable inspection techniques. Nearly for a decade composites have started to be used more widely in large commercial jet airliners for the fuselage, wing as well as other structural components in place of aluminium alloys due their high specific properties, reduced weight, fatigue performance and corrosion resistance. Although the increased use of composite materials reduced the role of aluminium up to some extent, high strength aluminium alloys remain important in airframe construction. Aluminium is a relatively low cost, light weight metal that can be heat treated and loaded to relatively high level of stresses, and it is one of the most easily produced of the high performance materials, which results in lower manufacturing and maintenance costs. There have been important recent advances in aluminium aircraft alloys that can effectively compete with modern composite materials. This study covers latest developments in enhanced mechanical properties of aluminium alloys, and high performance joining techniques. The mechanical properties on newly developed 2000, 7000 series aluminium alloys and new generation Al–Li alloys are compared with the traditional aluminium alloys. The advantages and disadvantages of the joining methods, laser beam welding and friction stir welding, are also discussed

  1. Shot peening of aluminium alloys

    International Nuclear Information System (INIS)

    Le Guernic, Y.

    1998-01-01

    Shot peening is a process of cold-hammering where a metallic surface is pelted with spherical grains. Each grain bumping into the surface acts as a hammer head and creates a small crater. The overlapping of these craters produces a residual compression layer just underneath the surface. It is well known that cracks cannot spread in a compression zone. In most cases of fatigue rupture and stress corrosion cracks propagate from the surface towards the inside so shot peening allows a longer lifetime of castings. Moreover most materials present a better resistance due to the cold-hammering effect of shot peening. Metallic surfaces can be treated in workshops or directly on site. Typical pieces that undergo shot peening on site are storing tanks, gas and steam turbines, tubes of steam generators and piping in oil or nuclear or chemical industries. This article describes shot peening from a theoretical and general point of view and presents the application to aluminium-lithium alloys. In the case of aluminium alloys shot peening can be used to shape the piece (peen-forming). (A.C.)

  2. Analysis tools for the design of aluminium extrusion dies

    NARCIS (Netherlands)

    Koopman, A.J.

    2009-01-01

    The aluminium extrusion process is a forming process where a billet of hot aluminium is pressed through a die to produce long straight aluminium profiles. A large variety of products with different and complex cross-sections can be made. The insight in the mechanics of the aluminium extrusion

  3. The physical and chemical reclamation and recycling of elements from black aluminium furnace residues

    OpenAIRE

    Siddique Pasley, Rehana

    2003-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University. Dross is the inevitable waste product generated by the world-wide primary and secondary aluminium industries. Around 3.5 million tonnes of white dross and 0.85 million tonnes of black dross are produced per year. Drosses are classified depending on metal content. White dross contains 40% and black dross contains 10% of aluminium. About half of the white dross is currently landfilled along wit...

  4. Alveolar proteinosis associated with aluminium dust inhalation.

    Science.gov (United States)

    Chew, R; Nigam, S; Sivakumaran, P

    2016-08-01

    Secondary alveolar proteinosis is a rare lung disease which may be triggered by a variety of inhaled particles. The diagnosis is made by detection of anti-granulocyte-macrophage colony-stimulating factor antibodies in bronchoalveolar lavage fluid, which appears milky white and contains lamellar bodies. Aluminium has been suggested as a possible cause, but there is little evidence in the literature to support this assertion. We report the case of a 46-year-old former boilermaker and boat builder who developed secondary alveolar proteinosis following sustained heavy aluminium exposure. The presence of aluminium was confirmed both by histological examination and metallurgical analysis of a mediastinal lymph node. Despite cessation of exposure to aluminium and treatment with whole-lung lavage which normally results in improvements in both symptoms and lung function, the outcome was poor and novel therapies are now being used for this patient. It may be that the natural history in aluminium-related alveolar proteinosis is different, with the metal playing a mediating role in the disease process. Our case further supports the link between aluminium and secondary alveolar proteinosis and highlights the need for measures to prevent excessive aluminium inhalation in relevant industries. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Irradiation effects on aluminium and beryllium

    International Nuclear Information System (INIS)

    Bieth, M.

    1992-01-01

    The High Flux Reactor (HFR) in Petten (The Netherlands) is a 45 MW light water cooled and moderated research reactor. The vessel was replaced in 1984 after more than 20 years of operation because doubts had arisen over the condition of the aluminium alloy construction material. Data on the mechanical properties of the aluminium alloy Al 5154 with and without neutron irradiation are necessary for the safety analysis of the new HFR vessel which is constructed from the same material as the old vessel. Fatigue, fracture mechanics (crack growth and fracture toughness) and tensile properties have been obtained from several experimental testing programmes with materials of the new and the old HFR vessel. 1) Low-cycle fatigue testing has been carried out on non-irradiated specimens from stock material of the new HFR vessel. The number of cycles to failure ranges from 90 to more than 50,000 for applied strain from 3.0% to 0.4%; 2) Fatigue crack growth rate testing has been conducted: - with unirradiated specimens from stock material of the new vessel; - with irradiated specimens from the remnants of the old core box. Irradiation has a minor effect on the sub-critical fatigue crack growth rate. The ultimate increase of the mean crack growth rate amounts to a factor of 2. However crack extension is strongly reduced due to the smaller crack length for crack growth instability (reduction of K IC ). - Irradiated material from the core box walls of the old vessel has been used for fracture toughness testing. The conditional fracture toughness values K IQ ranges from 30.3 down to 16.5 MPa√m. The lowermost meaningful 'K IC ' is 17.7 MPa√m corresponding to the thermal fluence of 7.5 10 26 n/m 2 for the End of Life (EOL) of the old vessel. - Testing carried out on irradiated material from the remnants of the old HFR core box shows an ultimate neutron irradiation hardening of 35 points increase of HSR 15N and an ultimate tensile yield stress of 589 MPa corresponding to the

  6. Epoxy coatings electrodeposited on aluminium and modified aluminium surfaces

    Directory of Open Access Journals (Sweden)

    Lazarević Zorica Ž.

    2002-01-01

    Full Text Available The corrosion behaviour and thermal stability of epoxy coatings electrodeposited on modified aluminum surfaces (anodized, phosphatized and chromatized-phosphatized aluminium were monitored during exposure to 3% NaCl solution, using electrochemical impedance spectroscopy (EIS and thermogravimetric analysis (TGA. Better protective properties of the epoxy coatings on anodized and chromatized-phosphatized aluminum with respect to the same epoxy coatings on aluminum and phosphatized aluminum were obtained: higher values of Rp and Rct and smaller values of Cc and Cd, from EIS, and a smaller amount of absorbed water inside the coating, from TGA. On the other hand, a somewhat lower thermal stability of these coatings was obtained (smaller values of the ipdt temperature. This behavior can be explained by the less porous structure of epoxy coatings on anodized and chromatized-phosphatized aluminum, caused by a lower rate of H2 evolution and better wet ability.

  7. Aluminium in Biological Environments: A Computational Approach

    Science.gov (United States)

    Mujika, Jon I; Rezabal, Elixabete; Mercero, Jose M; Ruipérez, Fernando; Costa, Dominique; Ugalde, Jesus M; Lopez, Xabier

    2014-01-01

    The increased availability of aluminium in biological environments, due to human intervention in the last century, raises concerns on the effects that this so far “excluded from biology” metal might have on living organisms. Consequently, the bioinorganic chemistry of aluminium has emerged as a very active field of research. This review will focus on our contributions to this field, based on computational studies that can yield an understanding of the aluminum biochemistry at a molecular level. Aluminium can interact and be stabilized in biological environments by complexing with both low molecular mass chelants and high molecular mass peptides. The speciation of the metal is, nonetheless, dictated by the hydrolytic species dominant in each case and which vary according to the pH condition of the medium. In blood, citrate and serum transferrin are identified as the main low molecular mass and high molecular mass molecules interacting with aluminium. The complexation of aluminium to citrate and the subsequent changes exerted on the deprotonation pathways of its tritable groups will be discussed along with the mechanisms for the intake and release of aluminium in serum transferrin at two pH conditions, physiological neutral and endosomatic acidic. Aluminium can substitute other metals, in particular magnesium, in protein buried sites and trigger conformational disorder and alteration of the protonation states of the protein's sidechains. A detailed account of the interaction of aluminium with proteic sidechains will be given. Finally, it will be described how alumnium can exert oxidative stress by stabilizing superoxide radicals either as mononuclear aluminium or clustered in boehmite. The possibility of promotion of Fenton reaction, and production of hydroxyl radicals will also be discussed. PMID:24757505

  8. Investigation of the aluminium-aluminium oxide reversible transformation as observed by hot stage electron microscopy.

    Science.gov (United States)

    Grove, C. A.; Judd, G.; Ansell, G. S.

    1972-01-01

    Thin foils of high purity aluminium and an Al-Al2O3 SAP type of alloy were oxidised in a specially designed hot stage specimen chamber in an electron microscope. Below 450 C, amorphous aluminium oxide formed on the foil surface and was first detectable at foil edges, holes, and pits. Islands of aluminium then nucleated in this amorphous oxide. The aluminium islands displayed either a lateral growth with eventual coalescence with other islands, or a reoxidation process which caused the islands to disappear. The aluminium island formation was determined to be related to the presence of the electron beam. A mechanism based upon electron charging due to the electron beam was proposed to explain the nucleation, growth, coalescence, disappearance, and geometry of the aluminium islands.

  9. Niobium-base grain refiner for aluminium

    International Nuclear Information System (INIS)

    Silva Pontes, P. da; Robert, M.H.; Cupini, N.L.

    1980-01-01

    A new chemical grain refiner for aluminium has been developed, using inoculation of a niobium-base compound. When a bath of molten aluminium is inoculated whith this refiner, an intermetallic aluminium-niobium compound is formed which acts as a powerful nucleant, producing extremely fine structure comparable to those obtained by means of the traditional grain refiner based on titanium and boron. It was found that the refinement of the structure depends upon the weight percentage of the new refiner inoculated as well as the time of holding the bath after inoculation and before pouring, but mainly on the inoculating temperature. (Author) [pt

  10. Aluminium Toxicity Targets in Plants

    Directory of Open Access Journals (Sweden)

    Sónia Silva

    2012-01-01

    Full Text Available Aluminium (Al is the third most abundant metallic element in soil but becomes available to plants only when the soil pH drops below 5.5. At those conditions, plants present several signals of Al toxicity. As reported by literature, major consequences of Al exposure are the decrease of plant production and the inhibition of root growth. The root growth inhibition may be directly/indirectly responsible for the loss of plant production. In this paper the most remarkable symptoms of Al toxicity in plants and the latest findings in this area are addressed. Root growth inhibition, ROS production, alterations on root cell wall and plasma membrane, nutrient unbalances, callose accumulation, and disturbance of cytoplasmic Ca2+ homeostasis, among other signals of Al toxicity are discussed, and, when possible, the behavior of Al-tolerant versus Al-sensitive genotypes under Al is compared.

  11. Irradiation effects in magnesium and aluminium alloys

    International Nuclear Information System (INIS)

    Sturcken, E.F.

    1979-01-01

    Effects of neutron irradiation on microstructure, mechanical properties and swelling of several magnesium and aluminium alloys were studied. The neutron fluences of 2-3 X 10 22 n/cm 2 , >0.2 MeV produced displacement doses of 20 to 45 displacements per atom (dpa). Ductility of the magnesium alloys was severely reduced by irradiation induced recrystallization and precipitation of various forms. Precipitation of transmuted silicon occurred in the aluminium alloys. However, the effect on ductility was much less than for the magnesium alloys. The magnesium and aluminium alloys had excellent resistance to swelling: The best magnesium alloy was Mg/3.0 wt% Al/0.19 wt% Ca; its density decreased by only 0.13%. The best aluminium alloy was 6063, with a density decrease of 0.22%. (Auth.)

  12. Deformation features of aluminium in tensile tests

    International Nuclear Information System (INIS)

    Quadros, N.F. de.

    1984-01-01

    It is presented a method to analyse stress-strain curves. Plastic and elastic strains were studied. The strains were done by tensile tests in four types of materials: highly pure aluminium, pure aluminium, commercially pure aluminium and aluminium - uranium. The chemical compositions were obtained by spectroscopy analysis and neutron activation analysis. Tensile tests were carried out at three strain rates, at room temperature, 100,200, 300 and 400 0 C, with knives extensometer and strain-gages to studied the elastic strain region. A multiple spring model based on two springs model to analyse elastic strain caused by tests without extensometers, taking in account moduli of elasticity and, an interactive analysis system with graphic capability were developed. It was suggested a qualitative model to explain the quantized multielasticity of Bell. (M.C.K.) [pt

  13. Aluminium Process Fault Detection and Diagnosis

    Directory of Open Access Journals (Sweden)

    Nazatul Aini Abd Majid

    2015-01-01

    Full Text Available The challenges in developing a fault detection and diagnosis system for industrial applications are not inconsiderable, particularly complex materials processing operations such as aluminium smelting. However, the organizing into groups of the various fault detection and diagnostic systems of the aluminium smelting process can assist in the identification of the key elements of an effective monitoring system. This paper reviews aluminium process fault detection and diagnosis systems and proposes a taxonomy that includes four key elements: knowledge, techniques, usage frequency, and results presentation. Each element is explained together with examples of existing systems. A fault detection and diagnosis system developed based on the proposed taxonomy is demonstrated using aluminium smelting data. A potential new strategy for improving fault diagnosis is discussed based on the ability of the new technology, augmented reality, to augment operators’ view of an industrial plant, so that it permits a situation-oriented action in real working environments.

  14. Computer simulation of the aluminium extrusion process

    Directory of Open Access Journals (Sweden)

    A. Śliwa

    2017-01-01

    Full Text Available The purpose of the work is computer simulation of the aluminium extrusion process using the Finite elements method (FEM. The impact of the speed of a punch falling on the material in the aluminium extrusion process was investigated. It was found that high stresses are created, leading to material destruction, if the punch is falling too fast. The design cycle is significantly reduced in multiple industrial applications if the FEM is applied, which enhances productivity and profits.

  15. Characterization of aluminium alloys rapidly solidified

    International Nuclear Information System (INIS)

    Monteiro, W.A.

    1988-01-01

    This paper discussed the investigation of the microstructural and mechanical properties of the aluminium alloys (3003; 7050; Al-9% Mg) rapidly solidified by melt spinning process (cooling rate 10 4 - 10 6 K/s). The rapidly solidification process of the studied aluminium alloys brought a microcrystallinity, a minimum presence of coarse precipitation and, also, better mechanical properties of them comparing to the same alloys using ingot process. (author) [pt

  16. Aluminium phosphide induced acute kidney injury

    Directory of Open Access Journals (Sweden)

    Quaiser Saif

    2015-01-01

    Full Text Available Aluminium phosphide is one of the most common agricultural poisons being consumed in north India. Consumption of a fresh tablet is lethal as no antidote is available. Acute intoxication primarily presents with cardiovascular collapse due to myocardial toxicity. We report here a case of acute severe poisoning along with cardiovascular collapse and oliguria. The patient developed acute kidney injury during the illness (a rare entity in aluminium phosphide poisoning, which completely resolved following prompt conservative treatment.

  17. Aluminium exclusion and aluminium tolerance in woody plants

    Directory of Open Access Journals (Sweden)

    Ivano eBrunner

    2013-06-01

    Full Text Available The aluminium (Al cation Al3+ is highly rhizotoxic and is a major stress factor to plants on acid soils, which cover large areas of tropical and boreal regions. Many woody plant species are native to acid soils and are well adapted to high Al3+ conditions. In tropical regions, both woody Al accumulator and non-Al accumulator plants occur, whereas in boreal regions woody plants are non-Al accumulators. The mechanisms of these adaptations can be divided into those that facilitate the exclusion of Al3+ from root cells (exclusion mechanisms and those that enable plants to tolerate Al3+ once it has entered the root and shoot symplast (internal tolerance mechanisms. The biochemical and molecular basis of these mechanisms have been intensively studied in several crop plants and the model plant Arabidopsis. In this review, we examine the current understanding of Al3+ exclusion and tolerance mechanisms from woody plants. In addition, we discuss the ecology of woody non-Al accumulator and Al accumulator plants, and present examples of Al3+ adaptations in woody plant populations. This paper complements previous reviews focusing on crop plants and provides insights into evolutionary processes operating in plant communities that are widespread on acid soils.

  18. TEM investigation of aluminium containing precipitates in high aluminium doped silicon carbide

    International Nuclear Information System (INIS)

    Wong-Leung, J.; FitzGerald, J.D.

    2002-01-01

    Full text: Silicon carbide is a promising semiconductor material for applications in high temperature and high power devices. The successful growth of good quality epilayers in this material has enhanced its potential for device applications. As a novel semiconductor material, there is a need for studying its basic physical properties and the role of dopants in this material. In this study, silicon carbide epilayers were grown on 4H-SiC wafers of (0001) orientation with a miscut angle of 8 deg at a temperature of 1550 deg C. The epilayers contained regions of high aluminium doping well above the solubility of aluminium in silicon carbide. High temperature annealing of this material resulted in the precipitation of aluminium in the wafers. The samples were analysed by secondary ion mass spectrometry and transmission electron microscopy. Selected area diffraction studies show the presence of aluminium carbide and aluminium silicon carbide phases. Copyright (2002) Australian Society for Electron Microscopy Inc

  19. Effect of aluminium phosphate as admixture on oxychloride cement

    Indian Academy of Sciences (India)

    Abstract. The effect of admixing of aluminium phosphate on oxychloride cement in the matrix has been investigated. It is shown that aluminium phosphate retards the setting process of the cement and improves water-tightness.

  20. Aluminium Diphosphamethanides: Hidden Frustrated Lewis Pairs.

    Science.gov (United States)

    Styra, Steffen; Radius, Michael; Moos, Eric; Bihlmeier, Angela; Breher, Frank

    2016-07-04

    The synthesis and characterisation of two aluminium diphosphamethanide complexes, [Al(tBu)2 {κ(2) P,P'-Mes*PCHPMes*}] (3) and [Al(C6 F5 )2 {κ(2) P,P'-Mes*PCHPMes*}] (4), and the silylated analogue, Mes*PCHP(SiMe3 )Mes* (5), are reported. The aluminium complexes feature four-membered PCPAl core structures consisting of diphosphaallyl ligands. The silylated phosphine 5 was found to be a valuable precursor for the synthesis of 4 as it cleanly reacts with the diaryl aluminium chloride [(C6 F5 )2 AlCl]2 . The aluminium complex 3 reacts with molecular dihydrogen at room temperature under formation of the acyclic σ(2) λ(3) ,σ(3) λ(3) -diphosphine Mes*PCHP(H)Mes* and the corresponding dialkyl aluminium hydride [tBu2 AlH]3 . Thus, 3 belongs to the family of so-called hidden frustrated Lewis pairs. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Steam Assisted Accelerated Growth of Oxide Layer on Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Yuksel, Serkan; Jellesen, Morten Stendahl

    2013-01-01

    Corrosion resistance of aluminium alloys is related to the composition and morphology of the oxide film on the surface of aluminium. In this paper we investigated the use of steam on the surface modification of aluminium to produce boehmite films. The study reveals a detailed investigation...... of the effect of vapour pressure, structure of intermetallic particles and thickness of boehmite films on the corrosion behaviour of aluminium alloys....

  2. Aluminium contents in infant and follow-on formula

    OpenAIRE

    German Federal Institute for Risk Assessment

    2012-01-01

    The presence of aluminium in food can have different causes. Thus, for example, it can be due to natural contents in certain food ingredients or aluminium-containing additives. Another source can be the transfer of aluminium from food packaging, cooking utensils, or kitchen equipment etc. Below, the Federal Institute for Risk Assessment (BfR) assesses aluminium contents in baby food with regard to their potential health effects. The trigger for the BfR opinion was a British study which me...

  3. Analysis of aluminium in rat following administration of allergen immunotherapy using either aluminium or microcrystalline-tyrosine-based adjuvants.

    Science.gov (United States)

    McDougall, Stuart A; Heath, Matthew D; Kramer, Matthias F; Skinner, Murray A

    2016-03-01

    Investigation into the absorption, distribution and elimination of aluminium in rat after subcutaneous aluminium adjuvant formulation administration using ICP-MS is described. Assays were verified under the principles of a tiered approach. There was no evidence of systemic exposure of aluminium, in brain or in kidney. Extensive and persistent retention of aluminium at the dose site was observed for at least 180 days after administration. This is the first published work that has quantified aluminium adjuvant retention based on the quantity of aluminium delivered in a typical allergy immunotherapy course. The results indicate that the repeated administration of aluminium-containing adjuvants will likely contribute directly and significantly to an individual's body burden of aluminium.

  4. Aluminium toxicity tolerance in crop plants: Present status of research

    African Journals Online (AJOL)

    ... tolerance of which genes of the Aluminium-activated malate transporter (ALMT) and multidrug and toxic compound extrusion (MATE) families are prominent. In this review, the progress of research in identifying aluminium toxicity tolerant genes is discussed. Keywords: Aluminium toxicity, soil acidity, hydroponic screening, ...

  5. Aluminium allergy and granulomas induced by vaccinations for children

    DEFF Research Database (Denmark)

    Andersen, Rosa Marie O; Zachariae, Claus; Johansen, Jeanne Duus

    2014-01-01

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site - vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we...... examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark....

  6. Design and Analysis of Butterfly Valve Disc Using Aluminium (1100 ...

    African Journals Online (AJOL)

    Aluminium (1100) is an extensively used material in the application of water line and drainage applications. If the aluminium (1100) surface contacts the water, an oxide layer will be formed and it prevents the corrosion of aluminium (1100) when compared to other metal and also it has less weight. But due to their low ...

  7. [Aluminium allergy and granulomas induced by vaccinations for children].

    Science.gov (United States)

    Andersen, Rosa Marie Ø; Zachariae, Claus; Johansen, Jeanne Duus

    2015-04-27

    Vaccination with aluminium-adsorbed vaccines can induce aluminium allergy with persistent itching subcutaneous nodules at the injection site – vaccination granulomas. In this article we give an overview of childhood aluminium-adsorbed vaccines available in Denmark. Through literature studies we examine the incidence, the symptoms and the prognosis for the vaccination granulomas and the allergy. Finally we discuss the status in Denmark.

  8. Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders

    NARCIS (Netherlands)

    De Kanter, J.L.C.G.

    2006-01-01

    Summary accompanying the thesis: Energy Absorption of Monolithic and Fibre Reinforced Aluminium Cylinders by Jens de Kanter This thesis presents the investigation of the crush behaviour of both monolithic aluminium cylinders and externally fibre reinforced aluminium cylinders. The research is based

  9. Aluminium and the human breast.

    Science.gov (United States)

    Darbre, P D

    2016-06-01

    The human population is exposed to aluminium (Al) from diet, antacids and vaccine adjuvants, but frequent application of Al-based salts to the underarm as antiperspirant adds a high additional exposure directly to the local area of the human breast. Coincidentally the upper outer quadrant of the breast is where there is also a disproportionately high incidence of breast cysts and breast cancer. Al has been measured in human breast tissues/fluids at higher levels than in blood, and experimental evidence suggests that at physiologically relevant concentrations, Al can adversely impact on human breast epithelial cell biology. Gross cystic breast disease is the most common benign disorder of the breast and evidence is presented that Al may be a causative factor in formation of breast cysts. Evidence is also reviewed that Al can enable the development of multiple hallmarks associated with cancer in breast cells, in particular that it can cause genomic instability and inappropriate proliferation in human breast epithelial cells, and can increase migration and invasion of human breast cancer cells. In addition, Al is a metalloestrogen and oestrogen is a risk factor for breast cancer known to influence multiple hallmarks. The microenvironment is established as another determinant of breast cancer development and Al has been shown to cause adverse alterations to the breast microenvironment. If current usage patterns of Al-based antiperspirant salts contribute to causation of breast cysts and breast cancer, then reduction in exposure would offer a strategy for prevention, and regulatory review is now justified. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

  10. Steam Initiated Surface Modification of Aluminium Alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud

    The extensive demand of aluminium alloys in various industries such as in transportationis mainly due to the high strength to weight ratio, which could be translated into fuel economy and efficiency. Corrosion protection of aluminium alloys is an important aspect for all applications which includes...... to 12 present various experimental results in the form of appended papers. The chapters consist of the experimental results obtained by the use of steam-based process and its effect on microstructureand corrosion resistance of the alloy as a function of steam pressure, use of various chemicals...... the use of aluminium alloys in the painted form requiring a conversion coating to improve the adhesion. Chromate based conversion coating processes are extremely good for these purposes, however the carcinogenic and toxic nature of hexavalent chromium led to the search for more benign and eco...

  11. Steam generated conversion coating on aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    Aluminium and its alloys are widely used in aerospace industry owing to their high strength to weight ratio. The surface of aluminium under normal conditions has a thin oxide film (2.5-10 nm) responsible for its inherent corrosion resistance. This oxide film can further be converted or transformed...... into functional conversion coatings in order to enhance corrosion resistance and adhesion to paint systems. Chromium based conversion coatings have been extensively used on aluminium alloys to improve adhesion of subsequent paint layers and corrosion resistance. However, the use of hexavalent chromium is strictly...... and growth of oxide film on different intermetallic particles and corrosion behaviour of such alloys.Surface morphology was observed by using FEG-SEM, EDX and FIB-SEM. Metal oxide surface characterization and compositional depth profiling were investigated by using XPS and GD-OES respectively...

  12. Internal friction in iron-aluminium alloys having a high aluminium content

    International Nuclear Information System (INIS)

    Hillairet, J.; Delaplace, J.; Silvent, A.

    1966-01-01

    By using a torsion pendulum to measure the internal friction of iron-aluminium alloys containing between 25 and 50 atom per cent of aluminium, it has been possible to show the existence of three damping peaks due to interstitial carbon. Their evolution is followed as a function of the carbon content, of the thermal treatment and of the aluminium content. A model based on the preferential occupation of tetrahedral sites is proposed as an interpretation of the results. A study of the Zener peak in these substitution alloys shows also that a part of the short distance disorder existing at high temperatures can be preserved by quenching. (author) [fr

  13. TITANIUM CARBON ALUMINIUM : A NOVEL GRAIN REFINER FOR ALUMINIUM-LITHIUM ALLOYS

    OpenAIRE

    Birch , M.; Cowell , A.

    1987-01-01

    This work explores the possibility of achieving grain size control in aluminium-lithium alloys with the titanium carbon aluminium (TiCAl) master alloys invented at the Technical University of Berlin and developed by London and Scandinavian Metallurgical Co Ltd (LSM). Grain refining tests were conducted on a single batch of 8090 alloy using addition rates of 0.2wt% and 0.4wt% of TiCAl and 3/1 titanium boron aluminium (TiBAl). Other tests using 0.4wt% of binary TiAl gave poor results, showing t...

  14. Failure of aluminium metal spray/organic duplex coating systems on structural steel

    OpenAIRE

    Sumon, T. A.; Scantlebury, J. D.; Lyon, S. B.

    2013-01-01

    Individually, aluminium metal spray (AMS) and organic paints are well established as effective protective coatings for steel substrates. These coatings are also frequently used together as duplex systems where their combination should produce a synergistic effect. However in certain, mainly marine, environments premature failure of such coatings, involving early blistering of the paint, has been observed in service after 3-5 years. This work aims to understand the mechanisms associated with t...

  15. Effect of flyash particles with aluminium melt on the wear of aluminium metal matrix composites

    Directory of Open Access Journals (Sweden)

    Vipin K. Sharma

    2017-08-01

    Full Text Available The present work deals with the fabrication and tribological testing of an aluminium flyash composite. The metal matrix selected was aluminium and flyash contents in different percentages were reinforced in it to fabricate the required metal matrix composite (MMC. Stir casting method was used to fabricate the MMC with 2–4–6% weight of flyash contents in aluminium. Tribological analysis of the tribo pairs formed between the smooth surfaces of cast iron disc and smooth MMC pin has been considered and friction force and wear of the MMC were investigated by using a Pin-on-disc setup. It was observed that the MMC with 6% weight of flyash content in aluminium matrix results in less wear (0.32 g and 4% weight of flyash content gives the low coefficient of friction (0.12 between the tribopairs of cast iron surface and MMC surface.

  16. Thermal formation of corundum from aluminium hydroxides ...

    Indian Academy of Sciences (India)

    This contains a higher concentration of anionic impurities related to differences in the solubility of the original aluminium salts. The sulfate is retained in the gel to higher temperatures at which its eventual decomposition may lead to the formation of a reactive pore structure which facilitates the nucleation of -Al2O3.

  17. Indentation of aluminium foam at low velocity

    Directory of Open Access Journals (Sweden)

    Shi Xiaopeng

    2015-01-01

    Full Text Available The indentation behaviour of aluminium foams at low velocity (10 m/s ∼ 30 m/s was investigated both in experiments and numerical simulation in this paper. A flat-ended indenter was used and the force-displacement history was recorded. The Split Hopkinson Pressure bar was used to obtain the indentation velocity and forces in the dynamic experiments. Because of the low strength of the aluminium foam, PMMA bar was used, and the experimental data were corrected using Bacon's method. The energy absorption characteristics varying with impact velocity were then obtained. It was found that the energy absorption ability of aluminium foam gradually increases in the quasi-static regime and shows a significant increase at ∼10 m/s velocity. Numerical simulation was also conducted to investigate this process. A 3D Voronoi model was used and models with different relative densities were investigated as well as those with different failure strain. The indentation energy increases with both the relative density and failure strain. The analysis of the FE model implies that the significant change in energy absorption ability of aluminium foam in indentation at ∼10 m/s velocity may be caused by plastic wave effect.

  18. Performance evaluation of aluminium test piece against ...

    African Journals Online (AJOL)

    Image processing with Catphan 700 uses the automated Quality Assurance software restricted to only Digital Imaging and Communications in Medicine images. For this reason, an aluminium (Al) test piece device was fabricated for image processing in different image format for spatial resolution measurement.

  19. Warm Deep Drawing of Aluminium Sheet

    NARCIS (Netherlands)

    Bolt, P.J.; Werkhoven, R.J.; van den Boogaard, Antonius H.

    2003-01-01

    Aluminium sheet drawing processes can be improved by manipulating local flow behaviour by means of elevated temperatures and temperature gradients in the tooling. Forming tests showed that a substantial improvement is possible not only for 5xxx but also for 6xxx series alloys. Finite element method

  20. Flexural buckling of fire exposed aluminium columns

    NARCIS (Netherlands)

    Maljaars, J.; Twilt, L.; Soetens, F.

    2009-01-01

    In order to study buckling of fire exposed aluminium columns, a finite element model is developed. The results of this model are verified with experiments. Based on a parametric study with the finite element model, it is concluded that the simple calculation model for flexural buckling of fire

  1. Aluminium hydroxide-induced granulomas in pigs

    DEFF Research Database (Denmark)

    Valtulini, S; Macchi, C; Ballanti, P

    2005-01-01

    The effect of intramuscular injection of 40 mg/2 ml aluminium hydroxide in the neck of pigs was examined in a number of ways. The investigation followed repeated slaughterhouse reports, according to which 64.8% of pigs from one particular farm were found at slaughter to have one or more nodules i...

  2. Generation and characterization of nano aluminium powder ...

    Indian Academy of Sciences (India)

    TECS

    Abstract. In the present study, nano aluminium particles were produced by wire explosion process (WEP) in nitrogen, argon and helium atmospheres. Thus produced nano particles were characterized through certain physico-chemical diagnostic studies using wide angle X-ray diffraction (WAXD) and by energy dispersive.

  3. Impact toughness of laser surface alloyed Aluminium

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2012-03-01

    Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4kW Nd:YAG laser and the impact resistance of the alloys was investigated. The alloying powders were a mixture of Ni, Ti and SiC in different proportions. Surfaces reinforced...

  4. Shape rheocasting of high purity aluminium

    CSIR Research Space (South Africa)

    Curle, UA

    2011-03-01

    Full Text Available It is demonstrated experimentally that using the Council for Scientific and Industrial Research Rheo Casting System and high pressure die casting it is possible to semi-solid process and cast into a shape high purity aluminium without a...

  5. Generation and characterization of nano aluminium powder ...

    Indian Academy of Sciences (India)

    TECS

    as a combustion product. This could be useful in reduced smoke applications, since the visibility ... combustion instability due to appropriate particulate damping. A low concentration of regular-sized aluminium ... tance and L the contribution by the internal inductance of the capacitor and the lead inductance. The basic circuit.

  6. Dissolution of aluminium-cladded fuel elements

    International Nuclear Information System (INIS)

    Bernhard, G.; Boessert, W.; Hladik, O.; Schwarzbach, R.

    1984-01-01

    In the molybdenum production plant at Rossendorf (AMOR) short-term irradiated aluminium-cladded fuel elements from the Rossendorf research reactor RFR are dissolved for the purpose of molybdenum 99 production. The dissolution behaviour of these fuel elements and the appropriate dissolver are described. (author)

  7. COMBINED ALUMINIUM SULFATE/HYDROXIDE PROCESS FOR ...

    African Journals Online (AJOL)

    process has higher fluoride removal efficiency than the Nalgonda Technique with an additional advantage of minimizing ... disadvantages of this technique include high residual aluminium concentration (2–7 mg/L) in the treated ... thermogravimetric analyzer (Mettler Toledo AG–TGA/SDTA851e, Switzerland) using ceramic.

  8. Molecular breeding of cereals for aluminium resistance

    Science.gov (United States)

    Aluminium (Al3+) toxicity is the primary factor limiting crop production on acidic soils worldwide. In addition to an application of lime for soil amelioration, Al3+ resistant plant varieties have been deployed to raise productivity on such hostile soils. This has been possible due to the exploita...

  9. Improving mechanical properties of aluminium alloy through ...

    African Journals Online (AJOL)

    This paper investigates the microstructure and mechanical properties of aluminum alloy (Al-Si-Fe) reinforced with coconut shell-ash particulate. The aluminium (Al-Si-Fe) alloy composite was produced by a double-stir casting process at a speed of 700 rpm for 10 and 5 minutes at first and second stirring respectively.

  10. Creep properties of aluminium processed by ECAP

    Czech Academy of Sciences Publication Activity Database

    Král, Petr; Dvořák, Jiří; Jäger, Aleš; Kvapilová, Marie; Horita, Z.; Sklenička, Václav

    2016-01-01

    Roč. 54, č. 6 (2016), s. 441-451 ISSN 0023-432X R&D Projects: GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 ; RVO:68378271 Keywords : equal channel angular pressing (ECAP) * aluminium * ultrafine-grained microstructure * creep Subject RIV: JG - Metallurgy; JG - Metallurgy (FZU-D) Impact factor: 0.366, year: 2016

  11. Constant structure creep experiments on aluminium

    Czech Academy of Sciences Publication Activity Database

    Milička, Karel

    2011-01-01

    Roč. 49, č. 5 (2011), s. 307-318 ISSN 0023-432X R&D Projects: GA AV ČR IAA2041203 Institutional research plan: CEZ:AV0Z20410507 Keywords : mechanical properties * high temperature deformation * creep * aluminium Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.451, year: 2011

  12. 42 CFR 35.35 - Unsalable articles.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Unsalable articles. 35.35 Section 35.35 Public... HOSPITAL AND STATION MANAGEMENT Disposition of Articles Produced by Patients § 35.35 Unsalable articles. Articles having no commercial value shall be stored, destroyed, or otherwise disposed of as the officer in...

  13. EFFECTS OF HOUSING SYSTEMS ON PRODUCTIVE PERFORMANCE OF COMMERCIAL LAYERS FOLLOWING INDUCED MOLTING BY ALUMINIUM OXIDE SUPPLEMENTATION

    Directory of Open Access Journals (Sweden)

    M. YOUSAF AND N. AHMAD1

    2006-07-01

    Full Text Available The project was carried out to compare the performance of molted layers by aluminium oxide supplementation in cages and on litter floor system. Seventy two Single Comb White Leghorn commercial layers (60 weeks old were divided into six experimental units of 12 layers each. These experimental units were randomly divided into two groups, each consisting of three experimental units, one group was reared on litter floor and the other in cages. The layers were provided with 35 gm feed containing 4 gm aluminium oxide/kg of feed for first 14 days of molting period (66-67 weeks of age. The layers showed significant reduction in body weight following induced molting by aluminium oxide under both housing systems. Body weight loss was higher, while feed consumption was lower, in the cages as compared to litter floor system. The layers molted by aluminium oxide showed significantly higher egg production in the cages (P≤0.05 than in litter floor system (P≤0.05. The layers in the subsequent production cycle showed improvement in egg weight, egg shell thickness and Haugh Unit Score. The egg weight and egg shell thickness were higher in the birds kept on litter floor system than those kept in cages (P≥0.05. However, Haugh unit score was higher in the cage system. It was concluded that aluminium oxide can be effectively supplemented for better production performance and improved egg quality in the second production cycle preferably in the cages.

  14. Corrosion fatigue behaviour of aluminium 5083-H111 welded using gas metal arc welding method

    CSIR Research Space (South Africa)

    Mutombo, K

    2011-12-01

    Full Text Available to the requirements of ASTM standards G31 [24] and G46 [25]. The 3.5% NaCl simulated sea water was prepared by dissolving 3.5 ? 0.1 parts by weight of Corrosion Fatigue Behaviour of Aluminium 5083-H111 Welded Using Gas Metal Arc Welding Method 193 NaCl in 96..., dissolve in some chemical solutions, such as strong acids or alkaline solutions. Damage to this passive layer in chloride-containing environments (such as sea water or NaCl solutions), may result in localised corrosive attack such as pitting corrosion...

  15. Aluminium in brain tissue in familial Alzheimer's disease.

    Science.gov (United States)

    Mirza, Ambreen; King, Andrew; Troakes, Claire; Exley, Christopher

    2017-03-01

    The genetic predispositions which describe a diagnosis of familial Alzheimer's disease can be considered as cornerstones of the amyloid cascade hypothesis. Essentially they place the expression and metabolism of the amyloid precursor protein as the main tenet of disease aetiology. However, we do not know the cause of Alzheimer's disease and environmental factors may yet be shown to contribute towards its onset and progression. One such environmental factor is human exposure to aluminium and aluminium has been shown to be present in brain tissue in sporadic Alzheimer's disease. We have made the first ever measurements of aluminium in brain tissue from 12 donors diagnosed with familial Alzheimer's disease. The concentrations of aluminium were extremely high, for example, there were values in excess of 10μg/g tissue dry wt. in 5 of the 12 individuals. Overall, the concentrations were higher than all previous measurements of brain aluminium except cases of known aluminium-induced encephalopathy. We have supported our quantitative analyses using a novel method of aluminium-selective fluorescence microscopy to visualise aluminium in all lobes of every brain investigated. The unique quantitative data and the stunning images of aluminium in familial Alzheimer's disease brain tissue raise the spectre of aluminium's role in this devastating disease. Copyright © 2016 The Authors. Published by Elsevier GmbH.. All rights reserved.

  16. Toxicity of dissolved and precipitated aluminium to marine diatoms.

    Science.gov (United States)

    Gillmore, Megan L; Golding, Lisa A; Angel, Brad M; Adams, Merrin S; Jolley, Dianne F

    2016-05-01

    Localised aluminium contamination can lead to high concentrations in coastal waters, which have the potential for adverse effects on aquatic organisms. This research investigated the toxicity of 72-h exposures of aluminium to three marine diatoms (Ceratoneis closterium (formerly Nitzschia closterium), Minutocellus polymorphus and Phaeodactylum tricornutum) by measuring population growth rate inhibition and cell membrane damage (SYTOX Green) as endpoints. Toxicity was correlated to the time-averaged concentrations of different aluminium size-fractions, operationally defined as diatom species. C. closterium was the most sensitive species (10% inhibition of growth rate (72-h IC10) of 80 (55-100)μg Al/L (95% confidence limits)) while M. polymorphus (540 (460-600)μg Al/L) and P. tricornutum (2100 (2000-2200)μg Al/L) were less sensitive (based on measured total aluminium). Dissolved aluminium was the primary contributor to toxicity in C. closterium, while a combination of dissolved and precipitated aluminium forms contributed to toxicity in M. polymorphus. In contrast, aluminium toxicity to the most tolerant diatom P. tricornutum was due predominantly to precipitated aluminium. Preliminary investigations revealed the sensitivity of C. closterium and M. polymorphus to aluminium was influenced by initial cell density with aluminium toxicity significantly (pdiatoms suggesting that mechanisms of aluminium toxicity to diatoms do not involve compromising the plasma membrane. These results indicate that marine diatoms have a broad range in sensitivity to aluminium with toxic mechanisms related to both dissolved and precipitated aluminium. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Electrochemical Estimation of the Corrosion Rate of Magnesium/Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    A. Pardo

    2010-01-01

    Full Text Available The corrosion rate of AZ31, AZ80, and AZ91D magnesium/aluminium alloys immersed in 3.5 wt.% NaCl was determined comparing gravimetric and electrochemical measurements. The findings revealed that, for all investigated materials, a fraction of the metallic surface exposed to the corrosive medium did not reveal a normal electrochemical response to the applied signal. This may be associated with phenomena such as partial disintegration of specimens into fine metallic particles, electrochemical formation of Mg+ ions, and/or anomalous chemical attack occurring simultaneously with the normal electrochemical corrosion attack. The abnormal electrochemical behaviour was more evident for lower amounts of aluminium in the bulk composition of the investigated materials. Thus, the electrochemical estimates of pure Mg and the AZ31 alloy were not reliable and tended to underestimate corrosion losses.

  18. [Association between serum aluminium level and methylation of amyloid precursor protein gene in workers engaged in aluminium electrolysis].

    Science.gov (United States)

    Yang, X J; Yuan, Y Z; Niu, Q

    2016-04-20

    To investigate the association between serum aluminium level and methylation of the promoter region of amyloid precursor protein (APP)gene in workers engaged in aluminium electrolysis. In 2012, 366 electrolysis workers in an aluminium factory were enrolled as exposure group (working years >10 and age >40 years)and divided into low-exposure group and high-exposure group based on the median serum aluminium level. Meanwhile, 102 workers in a cement plant not exposed to aluminium were enrolled as control group. Graphite furnace atomic absorption spectrometry was used to measure serum aluminium level, methylation specific PCR was used to measure the methylation rate of the promoter region of APP gene, and ELI-SA was used to measure the protein expression of APP in lymphocytes in peripheral blood. The exposure group had a significantly higher serum aluminium level than the control group (45.07 μg/L vs 30.51 μg/L, P0.05). The multivariate logistic regression analysis showed that with reference to the control group, low aluminium exposure (OR=1.86, 95% CI 1.67~3.52)and high aluminium exposure (OR=2.98, 95% CI 1.97~4.15)were risk factors for a reduced methylation rate of the promoter region of APP gene. Reduced methylation of the promoter region of APP gene may be associated with increased serum aluminium level, and downregulated methylation of the promoter region of APP gene may accelerate APP gene transcription.

  19. Nanostructure of aluminium (Al) - Doped zinc oxide (AZO) thin films

    Science.gov (United States)

    Hussin, Rosniza; Husin, M. Asri

    2017-12-01

    Aluminium (Al)-doped Zinc Oxide (ZnO) was deposited on glass substrates by using the sol-gel dip coating technique. Next, AZO sol-gel solution was produced via sol-gel method. Al was used as doped element with molar ratios of 1%, 2%, and 3%, while the calcination temperatures were set at 400°C, 500°C, and 600°C for 2 hours. In fact, characterization was carried out in order to determine the effect of calcination temperature and molar ratio of doping by using several techniques, such as X-Ray Diffraction (XRD), Atomic Force Microscopy (AFM), Field Emission Scanning Electron Microscopy (FESEM), and Ultraviolet-Visible spectroscopy (UV-Vis). XRD was performed to investigate the crystal structure in which the ZnO was in wurtzite hexagonal form. Next, Energy Dispersive Spectroscopy (EDS) was used to determine the composition of thin films where the result revealed the existence of zinc, oxygen, and aluminium. The roughness of the deposited film was later measured by using the AFM approach where the findings indicated increment in RMS from 8.496 nm to 35.883 nm as the temperature was increased. Additionally, FESEM was carried out to look into the microstructure surfaces of the deposited AZO thin film for increased temperature caused the particle to grow bigger for all molar ratio of dopant. Lastly, UV-Vis was conducted to study the optical properties of AZO, in which the result demonstrated that AZO thin film possessed the highest transmittance percentage among all samples above 90% with band gap value that ranged from 3.25 eV to 3.32 eV.

  20. High speed machining of aluminium gear box without temperature stabilization

    Directory of Open Access Journals (Sweden)

    Abilio P. SILVA

    2010-01-01

    Full Text Available At the present time both clutch and mechanism housings, which are the main components from automotive gear boxes, are made of special aluminium alloys. These alloys are extremely light when compared with steel, making them a perfect choice to mitigate the cars weight and machining costs. Nonetheless they possess a high thermal expansion coefficient, which can be considered a major disadvantage since it makes necessary to pay extraordinary attention to dimensional variations during the production cycle due to temperature deviations. High speed machining of precision components made of aluminium requests thus their temperature to become previously stable. This procedure is the only way to force dimensions to stay inside its tolerance intervals. The main purpose of the present work was to assess the possibility to avoid the use of special ovens to make the clutch housing temperature become stable prior to machining. The dimensional stabilization of 40 sample parts, pre-heated at three temperature levels, was accomplished through the use of this system. The achieved results were made possible by analysing the part’s temperature at the machine’s entrance, the machine’s interior temperature, 35 measured dimensions and their tolerance intervals as well as the average temperature deviations of each of the five considered batches. By analysing the obtained results in detail it was possible to determine which dimensions show high sensitiveness to temperature (high correlation between dimension’s variation and temperature. Among these dimensions we can point out the ones related with depth, since they display the highest deviations due to temperature. Being a work with practical application it was possible to confirm the benefit of using this methodology by achieving significant enhancements on production efficiency, energy savings and reduction on maintenance costs, through the application of small adjustments to the machining sequence and by

  1. Demethylation of Quinine Using Anhydrous Aluminium Trichloride

    Directory of Open Access Journals (Sweden)

    Aiyi Asnawi

    2011-03-01

    Full Text Available Quinine is a natural alkaloid having a methoxy group bound to quinoline ring and an allyl group bound to quinuclidine ring. Demethylation of quinine applying strong acid such as HBr or HI at high temperature was unsuccessful. The aim of this research was to obtain demethylated quinine by means of mild and selective demethylation procedure to prevent the addition reaction of allyl group. Selective demethylation of quinine has been carried out using anhydrous aluminium trichloride as reagent. The demethylation product was achieved in 68.12% yield by mole ratio of quinine to anhydrous aluminium trichloride of 1 to 4 in dried methylene chloride under nitrogen atmosphere. The reaction was firstly carried out at 0°C for 4 h and after the reaction mixture reached room temperature, the reaction was continued up to 24 h.

  2. Diagnostics of ytterbium/aluminium laser plasmas

    International Nuclear Information System (INIS)

    Bailey, J.; Lee, R.W.; Landen, O.L.; Kilkenny, J.D.; Lewis, C.L.; Busquet, M.

    1986-11-01

    Microdot spectroscopy was used to study the x-ray emission from laser-produced plasmas consisting of 10% ytterbium, 90% aluminium. Spectra were recorded with a space-resolving flat crystal (PET) mini-spectrometer in the 4.0-8.0 A range. The Janus research laser at LLNL irradiated the targets with green (0.53 μm) light in a 1 nsec pulse. The power density was varied between 4x10 13 and 3x10 14 W/cm 2 . The plasma electron density and temperature were determined from the aluminium XI, XII and XIII line emission. By examining correlations between changes in the plasma conditions with changes in the ytterbium spectra, we will determine the potential for using ytterbium line emission as a plasma diagnostic

  3. ALUHAB — The Superior Aluminium Foam

    Science.gov (United States)

    Babcsan, N.; Beke, S.; Makk, P.; Soki, P.; Számel, Gy; Degischer, H. P.; Mokso, R.

    A new metal foaming technology has been developed to produce aluminum foams with controlled cell sizes, a wide range of alloy compositions, and attractive mechanical properties. ALUHAB aluminium foams are manufactured from a special foamable aluminium alloy containing ultrafine particles (80-3000 nm). The technology uses high temperature ultrasonication to homogeneously disperse the particles and thus create a stable, foamable aluminum melt. Oscillating gas injector (loud-nozzle) technology permits the injection of optimally sized bubbles into the melt that are independent of the injector orifice diameter. Using this direct gas injection method, bubble size is regulated by the frequency and the power of the ultrasound, producing uniform bubble sizes in the sub-millimeter range. The technology results in extremely stable metal foams which can be cast into complex forms and re-melted without loss of foam integrity. Processing methods and properties of the ALUHAB foams will be discussed.

  4. Melt spun aluminium alloys for moulding optics

    Science.gov (United States)

    Gubbels, G.; Tegelaers, L.; Senden, R.

    2013-09-01

    Melt spinning is a rapid quenching process that makes it possible to create materials with a very fine microstructure. Due to this very fine microstructure the melt spinning process is an enabler for diamond turning optics and moulds without the need of post-polishing. Using diamond turning of melt spun aluminium one can achieve coating concept RSA-905 can be upgraded to a competitive alternative to steel in terms of price, performance and logistics. This paper presents some recent developments for improved mould performance of such concept. Hardness, wear resistance and adhesion are topics of interest and they can be applied by special coatings such as diamond-like carbon (DLC) and chromium nitride (CrN). These coatings make the aluminium alloy suitable for moulding mass production of small as well as larger optics, such as spectacle lenses.

  5. Feet sunk in molten aluminium: The burn and its prevention.

    Science.gov (United States)

    Alonso-Peña, David; Arnáiz-García, María Elena; Valero-Gasalla, Javier Luis; Arnáiz-García, Ana María; Campillo-Campaña, Ramón; Alonso-Peña, Javier; González-Santos, Jose María; Fernández-Díaz, Alaska Leonor; Arnáiz, Javier

    2015-08-01

    Nowadays, despite improvements in safety rules and inspections in the metal industry, foundry workers are not free from burn accidents. Injuries caused by molten metals include burns secondary to molten iron, aluminium, zinc, copper, brass, bronze, manganese, lead and steel. Molten aluminium is one of the most common causative agents of burns (60%); however, only a few publications exist concerning injuries from molten aluminium. The main mechanisms of lesion from molten aluminium include direct contact of the molten metal with the skin or through safety apparel, or when the metal splash burns through the pants and rolls downward along the leg. Herein, we report three cases of deep dermal burns after 'soaking' the foot in liquid aluminium and its evolutive features. This paper aims to show our experience in the management of burns due to molten aluminium. We describe the current management principles and the key features of injury prevention. Copyright © 2014 Elsevier Ltd and ISBI. All rights reserved.

  6. What is the risk of aluminium as a neurotoxin?

    Science.gov (United States)

    Exley, Christopher

    2014-06-01

    Aluminium is neurotoxic. Its free ion, Al(3+) (aq), is highly biologically reactive and uniquely equipped to do damage to essential cellular (neuronal) biochemistry. This unequivocal fact must be the starting point in examining the risk posed by aluminium as a neurotoxin in humans. Aluminium is present in the human brain and it accumulates with age. The most recent research demonstrates that a significant proportion of individuals older than 70 years of age have a potentially pathological accumulation of aluminium somewhere in their brain. What are the symptoms of chronic aluminium intoxication in humans? What if neurodegenerative diseases such as Alzheimer's disease are the manifestation of the risk of aluminium as a neurotoxin? How might such an (outrageous) hypothesis be tested?

  7. Simulation of aluminium STIR casting technique

    International Nuclear Information System (INIS)

    Hafizal Yazid; Mohd Harun; Hanani Yazid; Abd Aziz Mohamed; Muhammad Rawi Muhammad Zain; Zaiton Selamat; Mohd Shariff Sattar; Muhamad Jalil; Ismail Mustapha; Razali Kasim

    2006-01-01

    In this paper, the objective is to determine the optimum impeller speed correlated with holding time to achieve homogeneous reinforcement distribution for a particular set of experimental condition. Attempts are made to simulate the flow behaviourof the liquid aluminium using FLUENT software. Stepwise impeller speed ranging from 50 to 300 rpm.with 2 impeller angle blades of 45 and 90 degree with respect to the rotational plane were used

  8. Aluminium phosphide poising: a case report

    International Nuclear Information System (INIS)

    Hirani, S.A.A.; Rahman, A.

    2010-01-01

    This paper reports the case of a family in which three children were presented at Emergency Room (ER) with poisoning after the use of a pesticide at home. Initially, the cases were managed as routine cases of organophosphorus poisoning; however, the death of two children made the health team members realise that the poison's effects were delayed and devastating. Later, the compound was identified as Aluminium Phosphide (ALP), and the life of the last surviving child in the family was saved. (author)

  9. Helium behaviour in aluminium under hydrostatic pressure

    International Nuclear Information System (INIS)

    Sokurskij, Yu.N.; Tebus, V.N.; Zudilin, V.A.; Tumanova, G.M.

    1989-01-01

    Effect of hydrostatic compression on equilibrium helium bubbles in low aluminium-lithium alloy irradiated in reactor at 570 K is investigated. Measurements of hydrostatic density and electron-microscopic investigations have shown, that application of up to 2 GPa pressure reduces equilibrium size of helium bubbles and reduces helium swelling. Kinetics and thermodynamics of the process are considered with application of 'rigid sphere' equation which describes helium state in bubbles

  10. Swedish research on aluminium reactor technology

    International Nuclear Information System (INIS)

    Forsen, Bjoern

    1960-02-01

    A historical survey of the work done in Sweden this subject is given in the first part of the paper. The second part is elevated to a brief outline of the authors view of the present status of corrosion theories for aluminium in high temperature water. A theory where the crystallization of boehemite from the barrier layer is considered as an important control of the corrosion reaction is presented

  11. Multiply-negatively charged aluminium clusters and fullerenes

    Energy Technology Data Exchange (ETDEWEB)

    Walsh, Noelle

    2008-07-15

    Multiply negatively charged aluminium clusters and fullerenes were generated in a Penning trap using the 'electron-bath' technique. Aluminium monoanions were generated using a laser vaporisation source. After this, two-, three- and four-times negatively charged aluminium clusters were generated for the first time. This research marks the first observation of tetra-anionic metal clusters in the gas phase. Additionally, doubly-negatively charged fullerenes were generated. The smallest fullerene dianion observed contained 70 atoms. (orig.)

  12. Corrosion of Metal-Matrix Composites with Aluminium Alloy Substrate

    Directory of Open Access Journals (Sweden)

    B. Bobic

    2010-03-01

    Full Text Available The corrosion behaviour of MMCs with aluminium alloy matrix was presented. The corrosion characteristics of boron-, graphite-, silicon carbide-, alumina- and mica- reinforced aluminium MMCs were reviewed. The reinforcing phase influence on MMCs corrosion rate as well as on various corrosion forms (galvanic, pitting, stress corrosion cracking, corrosion fatique, tribocorrosion was discussed. Some corrosion protection methods of aluminium based MMCs were described

  13. No risk of Alzheimer's disease from aluminium in consumer products

    OpenAIRE

    German Federal Institute for Risk Assessment

    2007-01-01

    Aluminium is the third most frequent element in the earth's crust and occurs naturally in drinking water and other foods, particularly in fruit and vegetables. For consumers the main uptake route is food. There may be additional exposure from aluminium-containing food-contact articles like kitchen utensils, cans, foils or tubes from which the light metal migrates into the food. Furthermore, aluminium may also be contained in medicinal products to neutralise gastric acid, so-called antacids an...

  14. The aluminium content of infant formulas remains too high.

    Science.gov (United States)

    Chuchu, Nancy; Patel, Bhavini; Sebastian, Blaise; Exley, Christopher

    2013-10-08

    Recent research published in this journal highlighted the issue of the high content of aluminium in infant formulas. The expectation was that the findings would serve as a catalyst for manufacturers to address a significant problem of these, often necessary, components of infant nutrition. It is critically important that parents and other users have confidence in the safety of infant formulas and that they have reliable information to use in choosing a product with a lower content of aluminium. Herein, we have significantly extended the scope of the previous research and the aluminium content of 30 of the most widely available and often used infant formulas has been measured. Both ready-to-drink milks and milk powders were subjected to microwave digestion in the presence of 15.8 M HNO3 and 30% w/v H2O2 and the aluminium content of the digests was measured by TH GFAAS. Both ready-to-drink milks and milk powders were contaminated with aluminium. The concentration of aluminium across all milk products ranged from ca 100 to 430 μg/L. The concentration of aluminium in two soya-based milk products was 656 and 756 μg/L. The intake of aluminium from non-soya-based infant formulas varied from ca 100 to 300 μg per day. For soya-based milks it could be as high as 700 μg per day. All 30 infant formulas were contaminated with aluminium. There was no clear evidence that subsequent to the problem of aluminium being highlighted in a previous publication in this journal that contamination had been addressed and reduced. It is the opinion of the authors that regulatory and other non-voluntary methods are now required to reduce the aluminium content of infant formulas and thereby protect infants from chronic exposure to dietary aluminium.

  15. Improving the Crashworthiness of Aluminium Rail Vehicles

    Science.gov (United States)

    Zangani, Donato; Robinson, Mark; Kotsikos, George

    An experimental and modelling programme of work have been undertaken to predict the performance of aluminium welds in rail vehicles under highly dynamic loading conditions and provide design guidelines to reduce the likelihood of the occurrence of weld unzipping. Modelling of weld unzipping in large rail structures is a challenging task since it requires to deal with material instability, to take into account the uncertainties in material parameters and to address the problem of mesh resolution which together pose severe challenges to computability. The proposed methodology to the prediction of weld failure is based on the validation of the numerical models through correlation with laboratory scale tearing tests. The tearing tests were conducted on samples taken from real rail extrusions with the purpose of obtaining the failure parameters under dynamic loading and understanding the effect of weld material composition on joint behaviour. The validated material models were used to construct a FEA simulation of the collision of an aluminium rail car and investigate the effect of both joint geometry and welding techniques on the failure mechanism. Comparisons of the model with the failures observed in an aluminium rail vehicle that was involved in a high speed collision, have shown that it is possible to model the phenomenon of weld unzipping with good accuracy. The numerical models have also been used as a tool for the optimisation of joint design to improve crashworthiness.

  16. Aluminium in the rail transportation market

    Energy Technology Data Exchange (ETDEWEB)

    Zehnder, J. [Alcan Alesa Engineering Ltd., Zurich (Switzerland). Alcan Mass Transportation Systems

    2002-07-01

    Rail-transportation is not, as one might expect, a homogeneous market but extremely fragmented and even with huge differences from continent to continent, i.e. in North America freight transport is dominating whereas in Europe passenger transport prevails. A first segmentation splits infrastructure from vehicles. In a second layer of segmentation we distinguish between light rail vehicles, heavy metros, regional trains, intercity trains, high speed trains with and without tilting, maglev trains, freight vehicles and locomotives. Finally, we find aluminium applications in wheels, suspension parts, brake equipment, traction equipment, body structure, hang on parts and interior trim. On the infrastructure side best use of aluminium is in the field of power supply. In order to have the best solution for each application, all forms of products such as castings, forgings, flat rolled products and extrusions are needed and the engineers are using a broad choice or different alloys for all the requirements such as structural strength, decorative aspect, electrical conductivity, wear resistance, weldability, corrosion resistance etc. Innovation cycles in rail transportation are very slow, mainly because the expected life of vehicles is over 30 years and so no fleet owner will run the risk of getting vehicles with non-proven components, i.e. where a safe life of over 30 years cannot be shown. In the following the most important aluminium applications are shown and discussed. (orig.)

  17. Friction stir welding (FSW of aluminium foam sandwich panels

    Directory of Open Access Journals (Sweden)

    M. Bušić

    2016-07-01

    Full Text Available The article focuses on the influence of welding speed and tool tilt angle upon the mechanical properties at the friction stir welding of aluminium foam sandwich panels. Double side welding was used for producing butt welds of aluminium sandwich panels applying insertion of extruded aluminium profile. Such insertion provided lower pressure of the tool upon the aluminium panels, providing also sufficient volume of the material required for the weldment formation. Ultimate tensile strength and flexural strength for three-point bending test have been determined for samples taken from the welded joints. Results have confirmed anticipated effects of independent variables.

  18. Numerical predicting of recycling friendly wrought aluminium alloy compositions

    Directory of Open Access Journals (Sweden)

    Varužan Kevorkijan

    2013-09-01

    Full Text Available The model presented in this work enables the design of optimal (standard and non-standard “recycling-friendly” compositions and properties of wrought aluminium alloys with significantly increased amounts of post-consumed scrap. The following two routes were modelled in detail: (i the blending of standard and non-standard compositions of wrought aluminium alloys starting from post-consumed aluminium scrap sorted to various degrees simulated by the model; and (ii changing the initial standard composition of wrought aluminium alloys to non-standard “recycling friendly” ones - with broader concentration tolerance limits of alloying elements, without influencing the selected alloy properties, specified in advance.

  19. Investigation process of alcoholysis of hydride aluminium-adobe

    International Nuclear Information System (INIS)

    Numanov, M.I.; Normatov, I.Sh.; Mirsaidov, U.M.

    2001-01-01

    Considering of that process of acid treatment of aluminium-adobe hydride realizes in the ethyl alcohol media it was necessary study the process of alcoholysis of AlH 3 and aluminium additives. In the end of article authors became to conclusion that deficiency of spontaneous alcoholysis of AlH 3 in adobe caused by protective action of fiber; solvate ability of LiCl and alkoxy aluminium hydride of lithium-LiCl·CO 2 H 5 OH, Li Al(OC 2 H 5 ) 4 ·nC 2 H 5 OH decreasing the expectancy of responding of alcohol with aluminium hydride

  20. Serum aluminium levels of workers in the bauxite mines.

    Science.gov (United States)

    de Kom, J F; Dissels, H M; van der Voet, G B; de Wolff, F A

    1997-01-01

    Aluminium is produced from the mineral bauxite. Occupational exposure is reported during the industrial processing of aluminium and is associated with pulmonary and neurotoxicity. However, data on exposure and toxicity of workers in the open bauxite mining industry do not exist. Therefore, a study was performed to explore aluminium exposure in employees involved in this bauxite mining process in a Surinam mine. A group of workers occupationally exposed to aluminium in an open bauxite mine were compared with a group of nonexposed wood processors. Serum aluminium was analyzed using atomic absorption spectrometry Data from the clinical chemistry of the blood and a questionnaire were used to explore determinants for aluminium exposure. No significant difference between serum aluminium in the exposed (4.4 +/- 2.0 micrograms/L, n = 27) and control group (5.1 +/- 1.5 micrograms/L, n = 27) was detected. For the serum concentration of the clinical chemical variables (calcium, citrate, and creatinine), a statistically significant difference was computed (p < or = 0.02) between the exposed and control group. All levels were slightly higher in the exposed group; no statistically significant correlations with serum aluminium were found. In this study, serum aluminium values were in the normal range, no significant difference between the groups could be detected despite long-term occupational exposure.

  1. Trial finds better haemostasis with aluminium chloride during periapical surgery.

    Science.gov (United States)

    Mc Goldrick, Niall; Ross, Carly; Nelson, James

    2017-06-23

    DesignRandomised controlled trial in a university setting.InterventionPatients were randomised to epinephrine impregnated gauze or aluminium chloride for periapical surgery involving a single tooth with a periapical area of aluminium chloride group were analysed. Adequate haemostasis was achieved in 25 (52.1%) of the epinephrine group and 37 (72.5%) of the aluminium chloride group, a statistically significant difference.ConclusionsThe outcome showed better efficacy of haemostasis in the aluminium chloride group than in the gauze impregnated epinephrine group. The analysis of the patients and tooth-dependent variables showed no relationship with the effectiveness of haemostasis.

  2. Determination of Aluminium Content in Aluminium Hydroxide Formulation by FT-NIR Transmittance Spectroscopy

    DEFF Research Database (Denmark)

    Lai, Xuxin; Zheng, Yiwu; Søndergaard, Ib

    2007-01-01

    A method for determining the aluminium content of an aluminium hydroxide suspension using near infrared (NIR) transmittance spectroscopy has been developed. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used as reference method. The factors influencing the NIR analysis......-AES and NIR transmittance spectroscopy exhibit comparable precision and accuracy. The NIR method provides several advantages: no complicated sample preparation; easy to operate; fast and non-destructive. In conclusion, NIR transmittance spectroscopy can be an alternative analytical method for determining...

  3. A new synthesis process for aluminium nitride. Nouveau procede de synthese du nitrure d'aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Haussonne, J.M. (CNET, Centre Lannion B, 22 (France)); Lostec, J. (CNET, Centre Lannion B, 22 (France)); Bertot, J.P. (CNET, Centre Lannion B, 22 (France)); Lostec, L. (CNET, Centre Lannion B, 22 (France)); Sadou, S. (CNET, Centre Lannion B, 22 (France))

    1993-04-01

    Thermodynamic considerations show that, even at room temperature, pure aluminium can react with nitrogen to form the aluminium nitride AlN. However, pure aluminium does not exist: it is always surrounded by an alumina shell that protects the metal from further reactions. Furthermore, in the hypothesis where one has been able to make aluminium react with nitrogen, an aluminium nitride shell will protect as well the metal core from further oxidation. Prompted by the Lanxide process allowing to form Al/Al[sub 2]O[sub 3] composites, we have mixed aluminium powders with lithium salts, and easily synthesized pure aluminium nitride by heating the mixed powders in nitrigen at temperatures ranging from 800 to 1200 C. Starting from aluminium powders with a specific area ranging from 0.3 to 4 m[sup 2]/g, we have been able to produce aluminium nitride with specific are ranging from 1 to 20 m[sup 2]/g. Mixed with Y[sub 2]O[sub 3]-CaO and sintered at 1720 C in N[sub 2], we obtained AlN ceramics owning 92% density and 160 W/m.K thermal conductivity. (orig.).

  4. There is (still too much aluminium in infant formulas

    Directory of Open Access Journals (Sweden)

    Burrell Shelle-Ann M

    2010-08-01

    Full Text Available Abstract Background Infant formulas are sophisticated milk-based feeds for infants which are used as a substitute for breast milk. Historically they are known to be contaminated by aluminium and in the past this has raised health concerns for exposed infants. We have measured the aluminium content of a number of widely used infant formulas to determine if their contamination by aluminium and consequent issues of child health persists. Methods Samples of ready-made milks and powders used to make milks were prepared by microwave digestion of acid/peroxide mixtures and their aluminium content determined by THGA. Results The concentration of aluminium in ready-made milks varied from ca 176 to 700 μg/L. The latter concentration was for a milk for preterm infants. The aluminium content of powders used to make milks varied from ca 2.4 to 4.3 μg/g. The latter content was for a soya-based formula and equated to a ready-to-drink milk concentration of 629 μg/L. Using the manufacturer's own guidelines of formula consumption the average daily ingestion of aluminium from infant formulas for a child of 6 months varied from ca 200 to 600 μg of aluminium. Generally ingestion was higher from powdered as compared to ready-made formulas. Conclusions The aluminium content of a range of well known brands of infant formulas remains high and particularly so for a product designed for preterm infants and a soya-based product designed for infants with cow's milk intolerances and allergies. Recent research demonstrating the vulnerability of infants to early exposure to aluminium serves to highlight an urgent need to reduce the aluminium content of infant formulas to as low a level as is practically possible.

  5. Long-term effects of aluminium dust inhalation.

    Science.gov (United States)

    Peters, Susan; Reid, Alison; Fritschi, Lin; de Klerk, Nicholas; Musk, A W Bill

    2013-12-01

    During the 1950s and 1960s, aluminium dust inhalation was used as a potential prophylaxis against silicosis in underground miners, including in Australia. We investigated the association between aluminium dust inhalation and cardiovascular, cerebrovascular and Alzheimer's diseases in a cohort of Australian male underground gold miners. We additionally looked at pneumoconiosis mortality to estimate the effect of the aluminium therapy. SMRs and 95% CI were calculated to compare mortality of the cohort members with that of the Western Australian male population (1961-2009). Internal comparisons on duration of aluminium dust inhalation were examined using Cox regression. Aluminium dust inhalation was reported for 647 out of 1894 underground gold miners. During 42 780 person-years of follow-up, 1577 deaths were observed. An indication of increased mortality of Alzheimer's disease among miners ever exposed to aluminium dust was found (SMR=1.38), although it was not statistically significant (95% CI 0.69 to 2.75). Rates for cardiovascular and cerebrovascular death were above population levels, but were similar for subjects with or without a history of aluminium dust inhalation. HRs suggested an increasing risk of cardiovascular disease with duration of aluminium dust inhalation (HR=1.02, 95% CI 1.00 to 1.04, per year of exposure). No difference in the association between duration of work underground and pneumoconiosis was observed between the groups with or without aluminium dust exposure. No protective effect against silicosis was observed from aluminium dust inhalation. Conversely, exposure to aluminium dust may possibly increase the risk of cardiovascular disease and dementia of the Alzheimer's type.

  6. Recovery of aluminium, nickel-copper alloys and salts from spent fluorescent lamps.

    Science.gov (United States)

    Rabah, Mahmoud A

    2004-01-01

    This study explores a combined pyro-hydrometallurgical method to recover pure aluminium, nickel-copper alloy(s), and some valuable salts from spent fluorescent lamps (SFLs). It also examines the safe recycling of clean glass tubes for the fluorescent lamp industry. Spent lamps were decapped under water containing 35% acetone to achieve safe capture of mercury vapour. Cleaned glass tubes, if broken, were cut using a rotating diamond disc to a standard shorter length. Aluminium and copper-nickel alloys in the separated metallic parts were recovered using suitable flux to decrease metal losses going to slag. Operation variables affecting the quality of the products and the extent of recovery with the suggested method were investigated. Results revealed that total loss in the glass tube recycling operation was 2% of the SFLs. Pure aluminium meeting standard specification DIN 1712 was recovered by melting at 800 degrees C under sodium chloride/carbon flux for 20 min. Standard nickel-copper alloys with less than 0.1% tin were prepared by melting at 1250 degrees C using a sodium borate/carbon flux. De-tinning of the molten nickel-copper alloy was carried out using oxygen gas. Tin in the slag as oxide was recovered by reduction using carbon or hydrogen gas at 650-700 degrees C. Different valuable chloride salts were also obtained in good quality. Further research is recommended on the thermodynamics of nickel-copper recovery, yttrium and europium recovery, and process economics.

  7. Degradation of unglazed rough graphite-aluminium solar absorber surfaces in simulated acid and neutral rain

    International Nuclear Information System (INIS)

    Konttinen, P.; Lund, P.D.; Salo, T.

    2005-01-01

    Degradation mechanisms of unglazed solar absorber surfaces based on aluminium substrate were studied. Rough graphite-aluminium surfaces were total-immersion subjected to aerated and de-aerated simulated neutral and acid rain. Test conditions were based on calculated absorber stagnation temperature and global rain acidity measurements. Changes in optical properties, elemental composition and sample mass were examined by spectrometry, energy dispersive X-ray spectrometry and thermogravimetry, respectively. The absorbers exhibited almost no degradation at pH value of 3.5. At pH 5.5 alumina on the surface hydrated significantly degrading the optical properties of the surfaces severely in most cases. Therefore these absorber surfaces can not be recommended to be used in non-glazed applications if they are exposed to rain with pH exceeding ∼ 3.5-4.5. The total-immersion test needs to be developed further as the test results exhibited poor temperature and time dependency thus preventing accurate service lifetime estimates. Still, these tests were useful in determining favourable and non-favourable operating conditions for the absorber surfaces based on aluminium substrate. (author)

  8. Effect of Lubrication on Sliding Wear of Red Mud Particulate Reinforced Aluminium Alloy 6061

    Directory of Open Access Journals (Sweden)

    N. Panwar

    2017-09-01

    Full Text Available In present study, Red mud, an industrial waste, has been utilized as a reinforcement material to fabricate Aluminium 6061 matrix based metal matrix composite. Taguchi L18 orthogonal array has been employed for fabrication of composite castings and for conducting the tribological experimentation. ANOVA analysis has been applied to examine the effect of individual parameters such as sliding condition: dry and wet, reinforcement weight fraction, load, speed, and sliding distance on specific wear rate obtained experimentally. It has been found that tensile strength and impact energy increases while elongation decreases, with increasing weight fraction and decrease in particle size of red mud. The percentage contribution of the effect of factors on SWR is Sliding condition (73.17, speed (7.84, percentage reinforcement (7.35, load (5.75, sliding distance (2.24, and particle size (1.25. It has also been observed that specific wear rate is very low in wet condition. However, it decreases with increase in weight fraction of reinforcement, decrease in load and sliding speed. Al6061/red mud metal matrix composites have shown reasonable strength and wear resistance. The use of red mud in Aluminium composite provides the solution for disposal of red mud and can possibly become an economic replacement of Aluminium and its alloys.

  9. Aluminium and iron air pollution near an iron casting and aluminium foundry in Turin district (Italy).

    Science.gov (United States)

    Polizzi, Salvatore; Ferrara, Mauro; Bugiani, Massimiliano; Barbero, Domenico; Baccolo, Tiziana

    2007-09-01

    This work reports the results of an environmental survey carried out in an industrial area in the Province of Turin: its main aim is to assess the levels of iron and aluminium in the outside air during the period from July to September to assess the influence of industrial activity (a cast-iron and aluminium foundry) which is interrupted during the month of August, on the level of metals present in the air. Conducting the analysis during this period of time made it possible to avoid the confounding effect of pollution due to domestic central heating. The measurements were taken from nine areas at different distances from the foundry in the area and according to the direction of the prevailing winds, as deduced from the historical data. The results of this survey show a statistically significant difference in iron and aluminium levels in the outside air in the geographic areas between the two main periods examined: during August (no foundry activity) v/s July-September (foundry activity). The values recorded are: Aluminium 0.4+/-0.45 microg/m(3) v/s 1.12+/-1.29 microg/m(3) (pIron 0.95+/-0.56 microg/m(3) v/s 1.6+/-1.0 microg/m(3) (piron tended to be higher in the areas farther away from the foundry site in the areas located along the path of the prevailing winds.

  10. Mechanical properties of plasma-sprayed layers of aluminium and aluminium alloy on AZ 91

    Czech Academy of Sciences Publication Activity Database

    Kubatík, Tomáš František; Ctibor, Pavel; Mušálek, Radek; Janata, Marek

    2017-01-01

    Roč. 51, č. 2 (2017), s. 323-327 ISSN 1580-2949 R&D Projects: GA ČR(CZ) GP14-31538P Institutional support: RVO:61389021 Keywords : plasma spraying of aluminium * adhesion of coating * wear * magnesium alloy AZ91 Subject RIV: JG - Metallurgy OBOR OECD: Materials engineering Impact factor: 0.436, year: 2016

  11. Speciation analysis of aluminium and aluminium fluoride complexes by HPIC-UVVIS.

    Science.gov (United States)

    Frankowski, Marcin; Zioła-Frankowska, Anetta

    2010-10-15

    The study presents a new analytical method for speciation analysis in fractionation of aluminium fluoride complexes and free Al(3+) in soil samples. Aluminium speciation was studied in model solutions and soil extract samples by means of high performance ion chromatography (HPIC) with UV-VIS detection using post-column reaction with tiron for the separation and detection of aluminium fluoride complex and Al(3+) forms during one analysis. The paper presents particular stages of the chromatographic process optimization involving selecting the appropriate eluent strength, type of elution or concentration and quantity of derivatization reagent. HPIC was performed on a bifunctional analytical column Dionex IonPac CS5A. The use of gradient elution and the eluents A: 1M NH(4)Cl and B: water acidified to pH of eluent phase, enabled full separation of fluoride aluminium forms as AlF(2)(+), AlF(3)(0), AlF(4)(-) (first signal), AlF(2+) (second signal) and form Al(3+) in a single analytical procedure. The proposed new method HPIC-UVVIS was applied successfully in the quantitative and qualitative analysis of soil samples. Copyright © 2010 Elsevier B.V. All rights reserved.

  12. Aluminium and Alzheimer's disease: the science that describes the link

    National Research Council Canada - National Science Library

    Exley, Christopher

    2001-01-01

    ... that has been encircled is the gene for the amyloid precursor protein. (Thanks to Walter Lukiw for supplying this information.) Aluminium and Alzheimer's Disease: The Science that Describes the LinkAluminium and Alzheimer's Disease The Science that Describes the Link Edited by Christopher Exley Birchall Centre for Inorganic Chemistry and Materials Scienc...

  13. Enhanced corrosion protection by microstructural control of aluminium brazing sheet

    NARCIS (Netherlands)

    Norouzi Afshar, F.

    2013-01-01

    Aluminium brazing sheet is a sandwich material made out of two aluminium alloys (AA4xxx/AA3xxx) and is widely used in automotive heat exchangers. One of the main performance criteria for heat exchanger units is the lifetime of the product. The lifetime of the heat exchanger units is determined by

  14. An interesting and efficient green corrosion inhibitor for aluminium ...

    African Journals Online (AJOL)

    An interesting and efficient green corrosion inhibitor for aluminium from extracts of Moringa oleifera in acidic solution. ... L.A. Nnanna, I.O. Owate ... using gravimetric and thermometric techniques at 30 and 60oC. Results obtained showed that Moringa oleifera functioned as an excellent corrosion inhibitor for aluminium in the ...

  15. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    Unknown

    Abstract. Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the scientific ...

  16. Three body abrasion of laser surface alloyed aluminium AA1200

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2012-06-01

    Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4 kW Nd:YAG laser to improve the abrasion wear resistance. Aluminium surfaces reinforced with metal matrix composites and intermetallic phases were achieved. The phases present depended...

  17. Comparative study of highly dense aluminium- and gallium-doped ...

    Indian Academy of Sciences (India)

    Administrator

    cause of their optoelectronic properties in addition to low cost, high stability and excellent surface uniformity (low roughness). Doping zinc oxide with some elements like aluminium, gallium, boron, niobium and indium has a great impact for having enhancements of its optical and electrical properties. Aluminium and gallium ...

  18. Laser cladding of aluminium using TiB2

    CSIR Research Space (South Africa)

    Kumar, S

    2010-03-01

    Full Text Available Modification of Aluminium surface by injecting, dispersing and melting TiB2 powder with the help of a laser beam promises to enhance tribological properties of Aluminium. The present work consists of making single lines and various overlapping lines...

  19. The effects of aluminium and selenium supplementation on brain ...

    African Journals Online (AJOL)

    This in vivo study was designed to investigate the potential of aluminium (Al), in the absence of added iron, to participate in either antioxidant or pro-oxidant events. Some markers of oxidative stress were determined in liver and brain of rats exposed to aluminium lactate, either alone or in the presence of dietary supplements ...

  20. Effects and mechanisms of grain refinement in aluminium alloys

    Indian Academy of Sciences (India)

    2016-08-26

    Aug 26, 2016 ... Grain refinement plays a crucial role in improving characteristics and properties of cast and wrought aluminium alloys. Generally Al–Ti and Al–Ti–B master alloys are added to the aluminium alloys to grain refine the solidified product. The mechanism of grain refinement is of considerable controversy in the ...

  1. Carbonaceous alumina films deposited by MOCVD from aluminium ...

    Indian Academy of Sciences (India)

    Spectroscopic ellipsometry was used to characterize carbonaceous, crystalline aluminium oxide films grown on Si(100) by low-pressure metal organic chemical vapour deposition, using aluminium acetylacetonate as the precursor. The presence of carbon in the films, attribured to the use of a metalorganic precursor for the ...

  2. Aluminium removal from water after defluoridation with the electrocoagulation process.

    Science.gov (United States)

    Sinha, Richa; Mathur, Sanjay; Brighu, Urmila

    2015-01-01

    Fluoride is the most electronegative element and has a strong affinity for aluminium. Owing to this fact, most of the techniques used for fluoride removal utilized aluminium compounds, which results in high concentrations of aluminium in treated water. In the present paper, a new approach is presented to meet the WHO guideline for residual aluminium concentration as 0.2 mg/L. In the present work, the electrocoagulation (EC) process was used for fluoride removal. It was found that aluminium content in water increases with an increase in the energy input. Therefore, experiments were optimized for a minimum energy input to achieve the target value (0.7 mg/L) of fluoride in resultant water. These optimized sets were used for further investigations of aluminium control. The experimental investigations revealed that use of bentonite clay as coagulant in clariflocculation brings down the aluminium concentration of water below the WHO guideline. Bentonite dose of 2 g/L was found to be the best for efficient removal of aluminium.

  3. Combined Corrosion and Wear of Aluminium Alloy 7075-T6

    NARCIS (Netherlands)

    Liu, Y.; Mol, J.M.C.; Janssen, G.C.A.M.

    2016-01-01

    The aluminium alloy 7075-T6 is widely used in engineering. In some applications, like slurry transport, corrosion and abrasion occur simultaneously, resulting in early material failure. In the present work, we investigated the combined effect of corrosion and wear on the aluminium alloy 7075-T6. We

  4. Aluminium Tolerance of Four Bean ( Phaseolus vulgaris L.) Varieties ...

    African Journals Online (AJOL)

    Root elongation produced superior differential rating in assessing for aluminium toxicity in the beans. On the other hand, Eriochrome cyanine R staining lacked clear differentiation especially where there were marginal differences of Al tolerance. It follows that, screening for aluminium tolerance in common beans can ...

  5. Effects of surface treatment of aluminium alloy 1050 on the adhesion and anticorrosion properties of the epoxy coating

    Energy Technology Data Exchange (ETDEWEB)

    Sharifi Golru, S., E-mail: samanesharifi@aut.ac.ir [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, P.O. Box 15875-4413 Tehran (Iran, Islamic Republic of); Attar, M.M., E-mail: attar@aut.ac.ir [Department of Polymer Engineering and Color Technology, Amirkabir University of Technology, P.O. Box 15875-4413 Tehran (Iran, Islamic Republic of); Ramezanzadeh, B. [Department of Surface Coating and Corrosion, Institute for Color Science and Technology, No. 59,Vafamanesh St, Hosainabad Sq, Lavizan, Tehran (Iran, Islamic Republic of)

    2015-08-01

    Highlights: • Aluminium alloy 1050 was treated by zirconium-based (Zr) conversion coating. • The surface morphology and surface free energy of the samples were obtained. • The adhesion properties of the epoxy coating was studied on the treated samples. • The corrosion resistance of the epoxy coating was enhanced on treated samples. - Abstract: The objective of this work is to investigate the effects of zirconium-based (Zr) conversion coating on the adhesion properties and corrosion resistance of an epoxy/polyamide coating applied on the aluminium alloy 1050 (AA1050). Field emission scanning electron microscope (FE-SEM), energy dispersive X-ray spectrum (EDS), atomic force microscope (AFM) and contact angle measuring device were employed in order to characterize the surface characteristics of the Zr treated AA1050 samples. The epoxy/polyamide coating was applied on the untreated and Zr treated samples. The epoxy coating adhesion to the aluminium substrate was evaluated by pull-off test before and after 30 days immersion in 3.5% w/w NaCl solution. In addition, the electrochemical impedance spectroscopy (EIS) and salt spray tests were employed to characterize the corrosion protection properties of the epoxy coating applied on the AA1050 samples. Results revealed that the surface treatment of AA1050 by zirconium conversion coating resulted in the increase of surface free energy and surface roughness. The dry and recovery (adhesion strength after 30 days immersion in the 3.5 wt% NaCl solution) adhesion strengths of the coatings applied on the Zr treated aluminium samples were greater than untreated sample. In addition, the adhesion loss of the coating applied on the Zr treated aluminium substrate was lower than other samples. Also, the results obtained from EIS and salt spray test clearly revealed that the Zr conversion coating could enhance the corrosion protective performance of the epoxy coating significantly.

  6. Effects of surface treatment of aluminium alloy 1050 on the adhesion and anticorrosion properties of the epoxy coating

    International Nuclear Information System (INIS)

    Sharifi Golru, S.; Attar, M.M.; Ramezanzadeh, B.

    2015-01-01

    Highlights: • Aluminium alloy 1050 was treated by zirconium-based (Zr) conversion coating. • The surface morphology and surface free energy of the samples were obtained. • The adhesion properties of the epoxy coating was studied on the treated samples. • The corrosion resistance of the epoxy coating was enhanced on treated samples. - Abstract: The objective of this work is to investigate the effects of zirconium-based (Zr) conversion coating on the adhesion properties and corrosion resistance of an epoxy/polyamide coating applied on the aluminium alloy 1050 (AA1050). Field emission scanning electron microscope (FE-SEM), energy dispersive X-ray spectrum (EDS), atomic force microscope (AFM) and contact angle measuring device were employed in order to characterize the surface characteristics of the Zr treated AA1050 samples. The epoxy/polyamide coating was applied on the untreated and Zr treated samples. The epoxy coating adhesion to the aluminium substrate was evaluated by pull-off test before and after 30 days immersion in 3.5% w/w NaCl solution. In addition, the electrochemical impedance spectroscopy (EIS) and salt spray tests were employed to characterize the corrosion protection properties of the epoxy coating applied on the AA1050 samples. Results revealed that the surface treatment of AA1050 by zirconium conversion coating resulted in the increase of surface free energy and surface roughness. The dry and recovery (adhesion strength after 30 days immersion in the 3.5 wt% NaCl solution) adhesion strengths of the coatings applied on the Zr treated aluminium samples were greater than untreated sample. In addition, the adhesion loss of the coating applied on the Zr treated aluminium substrate was lower than other samples. Also, the results obtained from EIS and salt spray test clearly revealed that the Zr conversion coating could enhance the corrosion protective performance of the epoxy coating significantly

  7. Synthesis and electroluminescence properties of a new aluminium complex [5-choloro-8-hydroxyquinoline] bis [2,2'bipyridine] Aluminium Al(Bpy)2(5-Clq)

    Science.gov (United States)

    Kumar, Rahul; Bhargava, Parag; Srivastava, Ritu; Singh, Punita

    2015-11-01

    We have synthesized a new aluminium complex, [5-choloro-8-hydroxyquinoline] bis[2,2'bipyridine] Aluminium Al(Bpy)2(5-Clq) and characterized it for structural, thermal and photoluminescence properties. The prepared material was characterized by Fourier -transformed infra-red spectroscopy (FTIR), thermal gravimetric analysis (TGA) and photoluminescence. The prepared material showed thermal stability up to 240 °C. The photoluminescence spectrum of Al(Bpy)2(5-Clq) in toluene solution showed peak at 515 nm. This material was used as an emissive layer in organic light emitting diodes (OLEDs). The fundamental structure of device is ITO/F4-TCNQ(1 nm)/α-NPD(35 nm)/Al(Bpy)2(5-Clq) (35 nm)/BCP(6 nm)/Alq3(28 nm)/LiF(1 nm)/Al(150 nm). The device emits an yellowish green light (CIE coordinates, x = 0.32, y = 0.52) with maximum luminescence 314 Cd/m2 at 18 V. The maximum current efficiency of OLED was 0.09 Cd/A and maximum power efficiency was 0.03 lm/W at 9 V respectively.

  8. Aluminium Electroplating on Steel from a Fused Bromide Electrolyte

    Energy Technology Data Exchange (ETDEWEB)

    Prabhat Tripathy; Laura Wurth; Eric Dufek; Toni Y. Gutknecht; Natalie Gese; Paula Hahn; Steven Frank; Guy Fredrickson; J Stephen Herring

    2014-08-01

    A quaternary bromide bath (LiBr-KBr-CsBr-AlBr3) was used to electro-coat aluminium on steel substrates. The electrolyte was prepared by the addition of AlBr3 into the eutectic LiBr-KBr-CsBr melt. A smooth, thick, adherent and shiny aluminium coating could be obtained with 80 wt.% AlBr3 in the ternary melt. The SEM photographs of the coated surfaces suggest the formation of thick and dense coatings with good aluminium coverage. Both salt immersion and open circuit potential measurement suggest that the coatings did display good corrosion-resistance behavior. Annealing of the coated surfaces, prior to corrosion tests, suggested the robustness of the metallic aluminium coating in preventing the corrosion of the steel surfaces. Studies also indicated that the quaternary bromide plating bath can potentially provide a better aluminium coating on both ferrous and non-ferrous metals, including complex surfaces/geometries.

  9. Aluminium/iron reinforced polyfurfuryl alcohol resin as advanced biocomposites

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar

    2016-07-01

    Full Text Available Aluminium and iron are widely used in construction sectors for the preparation of advanced composites with epoxy resins as matrices. In recent times, there are several reports on the polymerization of polyfufuryl alcohol (PFA a thermoset bioresins from furfuryl alcohol (FA. FA is obtained from waste of sugarcane bagasse. In this work, first the possibility of curing PFA from FA in the presence of aluminium or iron has been explored. Absorbance results from colorimeter/spectrophotometerindicated that the curing of FA to PFA in presence of aluminium started easily while in presence of iron the curing of FA to PFA could not start. Based on the above results, aluminium wire reinforced composites were successfully prepared with three different weight fractions (0.13, 0.09 and 0.07 of aluminium wire. The mechanical properties of these composites were determined theoretically and reported.

  10. Calculation of electron transmission through aluminium foil

    International Nuclear Information System (INIS)

    Abroyan, M.A.; Mel'ker, A.I.; Mikhajlin, A.I.; Sirotinkin, V.V.; Tokmakov, I.L.

    1987-01-01

    Calculated by Monte Carlo method energy and angular distributions of electrons transmitted through aluminium foil with 50 μm thickness are presented. 200-500 electron energy ranges and angles of electron incidence on foil from 0 to 40 deg C are considered. That allows to use results for more universal accelerator group, for example, for accelerators with scanning beam used in industry. The received values of angular and energy characteristics allow to increase essentially estimation accuracy of accelerator extraction devices and dose distribution on irradiating item

  11. Deviatoric response of the aluminium alloy, 5083

    Science.gov (United States)

    Appleby-Thomas, Gareth; Hazell, Paul; Millett, Jeremy; Bourne, Neil

    2009-06-01

    Aluminium alloys such as 5083 are established light weight armour materials. As such, the shock response of these materials is of great importance. The shear strength of a material under shock loading provides an insight into its ballistic performance. In this investigation embedded manganin stress gauges have been employed to measure both the longitudinal and lateral components of stress during plate impact experiments over a range of impact stresses. In turn, these results were used to determine the shear strength and to investigate the time dependence of lateral stress behind the shock front to give an indication of material response.

  12. Convenient synthesis of deuterated aluminium hydrides

    Energy Technology Data Exchange (ETDEWEB)

    Pawelke, Roland H.; Felderhoff, Michael; Weidenthaler, Claudia [Max-Planck-Institut fuer Kohlenforschung, Kaiser-Wilhelm-Platz 1, 45470 Muelheim an der Ruhr (Germany); Schueth, Ferdi [Max-Planck-Institut fuer Kohlenforschung, Kaiser-Wilhelm-Platz 1, 45470 Muelheim an der Ruhr (Germany)], E-mail: schueth@mpi-muelheim.mpg.de

    2008-09-15

    We describe the ball-milling synthesis of alkali metal deuterides from commercial lithium aluminium deuteride. This reaction principle was exemplified by the mechanochemical synthesis of NaAlD{sub 4} and KAlD{sub 4}. NaAlD{sub 4} was prepared on the multi-gram scale by this procedure and purified by standard wet-chemical separation. Pure NaAlD{sub 4} was obtained and used for the synthesis of Ca(AlD{sub 4}){sub 2}. The formation of all products was verified by X-ray diffraction.

  13. Experimental fatigue curves for aluminium brazed areas

    Science.gov (United States)

    Dimitescu, A.; Babiş, C.; Niţoi, D. F.; Radu, C.

    2017-08-01

    An important factor for the quality of joints is the brazed area. The fatigue check occupies a major position among many test procedures and methods, especially by the joining technologies. The results of processing the fatigue data experiments for aluminium brazed samples are used to find the regression function and the response surface methodology. The fatigue process of mechanical components under service loading is stochastic in nature. The prediction of time-dependent fatigue reliability is critical for the design and maintenance planning of many structural components.

  14. Friction stir welding of single crystal aluminium

    DEFF Research Database (Denmark)

    Fonda, Richard Warren; Wert, John A.; Reynolds, A.P.

    2007-01-01

    Friction stir welds were prepared in different orientations in an aluminium single crystal. The welds were quenched to preserve the microstructure surrounding the tool and then electron backscattered diffraction was used to reveal the generation of grain boundaries and the evolution...... to new crystal orientations, producing new grain boundaries in the process. These refined grains develop a {112}. texture closer to the tool. Large conventionally recrystallised grains sometimes form in the outer regions of the refined grain structure, but become ever more deformed as they approach...

  15. Aluminium and the automobile. Aluminium und Automobil. Vortraege eines internationalen Symposiums der Aluminium-Zentrale, Duesseldorf, 1980

    Energy Technology Data Exchange (ETDEWEB)

    1981-04-01

    The first symposium on 'Aluminium and the Automobile' took place in March 1976. The lectures of the latest symposium report on the time in between; with special regard to the extent and intensity with wich aluminium - whose advantages and desadvantages are known - was a subject of research and development work done by car producers and parts- and accessory producing industry. Producers of engine blocks, wheels brakes, sunroofs, window-glass mechanisms, heat exchangers, air-filters, drive shafts - just to mention a few described their success but also gave and account of so far unsolved problems. Aluminum and car producers from abroad gave valuable contributions as well. Good news is the technical progress which was clearly reflected in all the lectures. The automobile of the future needs to be further developed in order te fulfill the requirements of lower weight and energy saving cost reduction is equally important for the German and European car industry due to the increasingly hard competitive struggle. Contrary to previous predictions a sufficient supply of alluminium with be available in the years to come.

  16. Gas accumulation at grain boundaries during 800 MeV proton irradiation of aluminium and aluminium-alloys

    DEFF Research Database (Denmark)

    Singh, Bachu Narain; Horsewell, Andy; Sommer, W. F.

    1986-01-01

    ) showed a complete absence of voids or bubbles in the grain interiors of the aluminium and the aluminium-alloys. Bubbles were clearly visible by TEM at grain boundaries in pure Al and the AlMg3 alloy; but bubbles were not visible in the Al6061 alloy. The bubble density in the AlMg3 alloy was considerably...

  17. Therapeutic effect of Sinapic acid in aluminium chloride induced dementia of Alzheimer’s type in rats

    Directory of Open Access Journals (Sweden)

    Souravh Bais

    2017-07-01

    Full Text Available Objective: To evaluate the effect of sinapic acid against Aluminium chloride-induced dementia of Alzheimer’s disease (AD type in rat. Methods: The study was designed to induce dementia by chronic exposure of aluminium chloride at a dose of 175 mg/kg, p.o. for a period of 25 days in rats and then divided into different groups, i.e. Treatment group, negative control and two groups of sinapic acid, (at a dose of 20 and 40mg/kg, p.o., where these groups treated and observed till the 35th day of experimental trial. The behavioural, neuronal and biochemical parameters were determined during or end of experiment. Histological changes in the brain were also observed. Results: Aluminium chloride at a dose of 175 mg/kg, o.p. had significantly induced the dementia and sinapic acid, at a dose of 40 mg/kg, p.o., possessed therapeutic effect against Aluminium chloride induced-dementia of AD type in rats. Conclusions: Sinapic acid is a class of compound wide spread in plant kingdom and could be a better source of neutraceuticals in brain disorders. The compound showed an in vivo MAO-A and MAO-B inhibiting activity and their role in Alzheimer’s disease type of dementia was unexplored. The article also provides information on acute toxicity of sinapic acid with no toxicological sign on brain with chronic dose of AlCl3.

  18. Reactions on carbon anodes in aluminium electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Eidet, Trygve

    1997-12-31

    The consumption of carbon anodes and energy in aluminium electrolysis is higher than what is required theoretically. This thesis studies the most important of the reactions that consume anode materials. These reactions are the electrochemical anode reaction and the airburn and carboxy reactions. The first part of the thesis deals with the kinetics and mechanism of the electrochemical anode reaction using electrochemical impedance spectroscopy. The second part deals with air and carboxy reactivity of carbon anodes and studies the effects of inorganic impurities on the reactivity of carbon anodes in the aluminium industry. Special attention is given to sulphur since its effect on the carbon gasification is not well understood. Sulphur is always present in anodes, and it is expected that the sulphur content of available anode cokes will increase in the future. It has also been suggested that sulphur poisons catalyzing impurities in the anodes. Other impurities that were investigated are iron, nickel and vanadium, which are common impurities in anodes which have been reported to catalyze carbon gasification. 88 refs., 92 figs., 24 tabs.

  19. Dietary exposure to aluminium of the Hong Kong population.

    Science.gov (United States)

    Wong, Waiky W K; Chung, Stephen W C; Kwong, K P; Yin Ho, Yuk; Xiao, Ying

    2010-04-01

    A total of 256 individual food samples were collected in Hong Kong for aluminium testing. Most of food samples were analysed in ready-to-eat form. High aluminium levels were found in steamed bread/bun/cake (mean: 100-320 mg kg(-1)), some bakery products such as muffin, pancake/waffle, coconut tart and cake (mean: 250, 160, 120 and 91 mg kg(-1), respectively), and jellyfish (ready-to-eat form) (mean: 1200 mg kg(-1)). The results demonstrated that aluminium-containing food additives have been widely used in these food products. The average dietary exposure to aluminium for a 60 kg adult was estimated to be 0.60 mg kg(-1) bw week(-1), which amounted to 60% of the new PTWI established by JECFA. The main dietary source was "steamed bread/bun/cake", which contributed to 60% of the total exposure, followed by "bakery products" and "jellyfish", which contributed to 23 and 10% of the total exposure, respectively. However, the estimation did not include the intake of aluminium from natural food sources, food contact materials or other sources (e.g. drinking water). Although the results indicated that aluminium it is unlikely to cause adverse health effect for the general population, the risk to some populations who regularly consume foods with aluminium-containing food additives cannot be ruled out.

  20. New developments in aluminium titanate ceramics and refractories

    Energy Technology Data Exchange (ETDEWEB)

    Alecu, I.D.; Cilia, R.A.; Dean, G.A.; Reuben, R.; Stead, R.J.; Wing, R.F. [Rojan Advanced Ceramics Pty Ltd., Spearwood, WA (Australia)

    2002-07-01

    During the recent years there has been a world-wide resurgence in the interest for aluminium titanate ceramics. Aluminium titanate (AT) possesses a unique collection of outstanding properties that make it a favourite candidate for applications where thermal shock resistance, thermal and / or phonic insulation, or compatibility with molten metals are key requirements. Particularly promising are the applications of aluminium titanate in the non-ferrous metallurgical industry, primarily in aluminium smelters and foundries. Aluminium titanate is best suitable for manufacturing ceramic components for gravity and low-pressure die casting of non-ferrous metals and alloys. Examples of such components are casting nozzles and spouts, sprue bushes, connecting tubes, riser tubes, etc. As aluminium titanate (AT) is generally known as a ceramic material with a modest mechanical strength, most applications have been so far as components that either are small enough, or are subjected to small enough mechanical loads, so that the risk of failure is acceptably low. Currently there is an increasing demand for larger and / or stronger components, which obviously require significantly stronger aluminium titanate ceramic materials, as well as adequate forming technologies. (orig.)

  1. Does allergen-specific immunotherapy induce contact allergy to aluminium?

    Science.gov (United States)

    Netterlid, Eva; Hindsén, Monica; Siemund, Ingrid; Björk, Jonas; Werner, Sonja; Jacobsson, Helene; Güner, Nuray; Bruze, Magnus

    2013-01-01

    Persistent, itching nodules have been reported to appear at the injection site after allergen-specific immuno-therapy with aluminium-precipitated antigen extract, occasionally in conjunction with contact allergy to aluminium. This study aimed to quantify the development of contact allergy to aluminium during allergen-specific immunotherapy. A randomized, controlled, single-blind multicentre study of children and adults entering allergen-specific immunotherapy was performed using questionnaires and patch-testing. A total of 205 individuals completed the study. In the 3 study groups all subjects tested negative to aluminium before allergen-specific immunotherapy and 4 tested positive after therapy. In the control group 4 participants tested positive to aluminium. Six out of 8 who tested positive also had atopic dermatitis. Positive test results were found in 5/78 children and 3/127 adults. Allergen-specific immunotherapy was not shown to be a risk factor for contact allergy to aluminium. Among those who did develop aluminium allergy, children and those with atopic dermatitis were more highly represented.

  2. The varied functions of aluminium-activated malate transporters-much more than aluminium resistance.

    Science.gov (United States)

    Palmer, Antony J; Baker, Alison; Muench, Stephen P

    2016-06-15

    The ALMT (aluminium-activated malate transporter) family comprises a functionally diverse but structurally similar group of ion channels. They are found ubiquitously in plant species, expressed throughout different tissues, and located in either the plasma membrane or tonoplast. The first family member identified was TaALMT1, discovered in wheat root tips, which was found to be involved in aluminium resistance by means of malate exudation into the soil. However, since this discovery other family members have been shown to have many other functions such as roles in stomatal opening, general anionic homoeostasis, and in economically valuable traits such as fruit flavour. Recent evidence has also shown that ALMT proteins can act as key molecular actors in GABA (γ-aminobutyric acid) signalling, the first evidence that GABA can act as a signal transducer in plants. © 2016 The Author(s). Published by Portland Press Limited on behalf of the Biochemical Society.

  3. Corrosion issues of powder coated AA6060 aluminium profiles

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Valgarðsson, Smári; Jellesen, Morten Stendahl

    2015-01-01

    In this study detailed microstructural investigation of the reason for unexpected corrosion of powder coated aluminium alloy AA6060 windows profiles has been performed. The results from this study reveals that the failure of the window profiles was originated from the surface defects present...... on the extruded AA6060 aluminium profile after metallurgical process prior to powder coating. Surface defects are produced due to intermetallic particles in the alloy, which disturb the flow during the extrusion process. The corrosion mechanism leading to the failure of the powder coated AA6060 aluminium profiles...

  4. Recurrent sterile abscesses following aluminium adjuvant-containing vaccines.

    Science.gov (United States)

    Klein, Nicola P; Edwards, Kathryn M; Sparks, Robert C; Dekker, Cornelia L

    2009-01-01

    Abscess formation following immunisation is a previously reported complication, generally associated with microbial contamination of the vaccine. Less commonly, such abscesses have been sterile. Here we describe two children evaluated in the Center for Disease Control and Prevention (CDC)-funded Clinical Immunization Safety Assessment (CISA) network who developed recurrent sterile abscesses after administration of vaccines containing aluminium adjuvant, either individually or in combination. Although the abscesses healed without sequelae, these occurrences support an association between receipt of aluminium adjuvant and sterile abscesses in susceptible patients. For patients with similar symptoms, clinicians may wish to choose a vaccine formulation containing the least amount of aluminium adjuvant.

  5. Aluminium determination in U Alx using atomic absorption spectrophotometry

    International Nuclear Information System (INIS)

    Dantas, E.S.K.; Pires, M.A.F.

    1994-01-01

    Available as short communication only. A method for aluminium determination in uranium-aluminium dispersions (U al x ) using atomic absorption spectrometry is presented. The sample is dissolved in nitric acid, heated, dried, and market up the volume with 0.1 N H NO 3 . The uranium is precipitated with 30% NaOH and the aluminium is determined in the solution after filtration. The determination limit achieved was 5 μg Al/mL. The method is reproducible. (author). 7 refs, 2 tabs

  6. Effect of pressurized steam on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Ambat, Rajan

    2012-01-01

    Purpose - The purpose of this paper is to understand the effect of pressurized steam on surface changes, structures of intermetallic particles and corrosion behavior of AA1050 aluminium. Design/methodology/approach - Industrially pure aluminium (AA1050, 99.5 per cent) surfaces were exposed...... reactivities was observed due to the formation of the compact oxide layer. Originality/value - This paper reveals a detailed investigation of how pressurized steam can affect the corrosion behaviour of AA1050 aluminium and the structure of Fe-containing intermetallic particles....

  7. Orbital friction stir welding of aluminium pipes

    International Nuclear Information System (INIS)

    Engelhard, G.; Hillers, T.

    2002-01-01

    Friction stir welding (FSW) was originally developed for flat plates. This contribution shows how it can be applied to the welding of aluminium pipes. Pipes made of AlMG 3 (EN5754), AlMg 4.5Mn (EN5083) and AlMgSi 0.5 (EN6106) with dimensions of Da 600 and 520 x 10-8 mm were welded. The FSW orbital system comprises an annular cage with integrated FSW head, a hydraulic system, and a control unit. The welds were tested successfully according to EN 288. The mechanical and technical properties of the welds were somewhat better than with the TIG orbital process, and welding times were about 40 percent shorter [de

  8. Brazing of Titanium with Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    Winiowski A.

    2017-06-01

    Full Text Available This study presents results of vacuum diffusion brazing of Grade 2 titanium with 6082 (AlMg1Si0.6Cu0.3 aluminium alloy using B-Ag72Cu-780 (Ag72Cu28 grade silver brazing metal as an interlayer. Brazed joints underwent shear tests, light-microscopy-based metallographic examinations and structural examinations using scanning electron microscopy (SEM and X-ray energy dispersive spectrometry (EDS. The highest quality and shear strength of 20 MPa was characteristic of joints brazed at 530°C with a 30-minute hold. The structural examinations revealed that in diffusion zone near the boundary with titanium the braze contained solid solutions based on hard and brittle Ti-Al type intermetallic phases determining the strength of the joints.

  9. Experimental analysis of cut welding in aluminium

    DEFF Research Database (Denmark)

    Dorph, Pernille; De Chiffre, Leonardo; Bay, Niels

    1993-01-01

    Cut welding is a newly developed cold pressure welding process. In the present work, an experimental investigation was carried out analyzing the mechanisms involved in cut welding of a block to a strip. Experiments were carried out in technically pure aluminium. The investigation has involved...... tensile testing and metallographic investigations of the welds. The results show that this variant of cut welding is a very reproducible process giving a weld strength equal to 30-40% the strength of the parent material. The experiments have shown that the reason for this relatively low strength...... is an uneven pressure distribution along the weld due to a wave formed during sliding. Attempts to alter the material flow during sliding are presented....

  10. Study of hydrogen implanted in aluminium

    International Nuclear Information System (INIS)

    Bugeat, J.P.; Chami, A.C.; Danielou, R.; Ligeon, E.

    1976-01-01

    An aluminium sample was implanted with deuterium and hydrogen at 5keV and 10keV respectively. The 1 H( 11 B,α) 8 Be* and D( 3 He,p) 4 He reactions were used for the analysis of H and D respectively. The implanted deuterium was shown to be as a whole in a tetrahedral site as far as the implantation temperature is lower than 175K, beyond that temperature the deuterium is randomly located. When the implantation temperature increases from 33K up to 275K the tetrahedral siting remains during annealing. The migration temperatures of hydrogen (or temperature of transition from the tetrahedral siting to a random distribution) experimentally observed during annealing (300K) and for increased implantation temperatures, show that the tetrahedral site is associated with a monovacancy migrating at 300K, the diffusion temperature of hydrogen being lower than 180K [fr

  11. Silane based coating of aluminium mold

    DEFF Research Database (Denmark)

    2013-01-01

    A method of preparing an aluminum mold for injection molding is provided, the method comprises the steps of providing an aluminum mold having a least one surface, subjecting the at least one surface to a gas or liquid phase silane to thereby form an anti-stiction coating, the anti-stiction coating...... comprising a chemically bonded monolayer of silane compounds on the at least one surface wherein the silane is a halogenated silane. The at least one surface coated with the anti-stiction coating may be configured to withstand an injection molding process at a pressure above 100 MPa. Furthermore, a mold...... having at least one closed cavity is provided, at least one surface of the at least one cavity being an aluminium surface coated with a silane based coating layer. The silane based anti-stiction coating improves the anti-stiction properties of the mold which may allow for molding and demolding...

  12. Water state in basic aluminium tungstates

    International Nuclear Information System (INIS)

    Pozharskaya, L.A.; Pitsyuga, V.G.; Mokhosoev, M.V.

    1978-01-01

    Water state in basic aluminium tungstates is investigated using the method of proton magnetic resonance. Existence of various types of water molecules, differing by their geometry and bond energies, is established in the investigated compounds. The obtained results permit to suppose that in Al 6 (OH) 16 WO 4 x10H 2 O, AL 4 (OH) 10 WO 4 x5,5H 2 O and Al 3 (OH) 7 WO 7 x7H 2 O compounds coordinationally non-saturated oxygen atoms in anion are saturated basically at the expense of OH-groups, and water molecules form hydrogen bonds as opposed to Al 2 (OH) 4 WO 4 x7H 2 O and AlOH(WO 4 )x8.5H 2 O in which a considerable part of water molecules is bound directly with anion oxygen atoms

  13. Aluminium alloys in municipal solid waste incineration bottom ash.

    Science.gov (United States)

    Hu, Yanjun; Rem, Peter

    2009-05-01

    With the increasing growth of incineration of household waste, more and more aluminium is retained in municipal solid waste incinerator bottom ash. Therefore recycling of aluminium from bottom ash becomes increasingly important. Previous research suggests that aluminium from different sources is found in different size fractions resulting in different recycling rates. The purpose of this study was to develop analytical and sampling techniques to measure the particle size distribution of individual alloys in bottom ash. In particular, cast aluminium alloys were investigated. Based on the particle size distribution it was computed how well these alloys were recovered in a typical state-of-the-art treatment plant. Assessment of the cast alloy distribution was carried out by wet physical separation processes, as well as chemical methods, X-ray fluorescence analysis and electron microprobe analysis. The results from laboratory analyses showed that cast alloys tend to concentrate in the coarser fractions and therefore are better recovered in bottom ash treatment plants.

  14. Oxygen–induced barrier height changes in aluminium – amorphous ...

    African Journals Online (AJOL)

    Se) films by exposing the samples to oxygen before the aluminium contacts were deposited. Current – voltage (I-V) measurements were carried out on the samples. The results show that the application of voltage causes charge exchange ...

  15. Tailored Aluminium based Coatings for Optical Appearance and Corrosion Resistance

    DEFF Research Database (Denmark)

    Aggerbeck, Martin

    The current project investigated the possibility of designing aluminium based coatings focusing on the effect of composition and surface finish on the optical appearance and on the alkaline corrosion properties using titanium as the main alloying element. The main results and discussions...... of these applications, but the use of recycled aluminium compromises this due to the presence of increased levels of impurity and alloying elements. Knowledge on how different alloying elements affect the optical appearance might therefore increase the applicability of recycled aluminium. It was investigated how...... the optical appearance is affected by the alloy composition, surface morphology, and the microstructure. Four commercial aluminium alloys were studied before and after polishing, etching, anodisation, and hot water sealing, giving an overview on how the alloy composition affects the appearance. It was found...

  16. The management of Frey's syndrome with aluminium chloride hexahydrate antiperspirant.

    OpenAIRE

    Black, M. J.; Gunn, A.

    1990-01-01

    Nine patients suffering from gustatory sweating (Frey's syndrome) following parotidectomy have been treated by topical applications of aluminium chloride hexahydrate. Treatment has successfully controlled gustatory sweating using application intervals varying from 1 to 50 days.

  17. The management of Frey's syndrome with aluminium chloride hexahydrate antiperspirant.

    Science.gov (United States)

    Black, M. J.; Gunn, A.

    1990-01-01

    Nine patients suffering from gustatory sweating (Frey's syndrome) following parotidectomy have been treated by topical applications of aluminium chloride hexahydrate. Treatment has successfully controlled gustatory sweating using application intervals varying from 1 to 50 days. Images Figure 1 PMID:2301903

  18. Deposition of aluminium nanoparticles using dense plasma focus device

    International Nuclear Information System (INIS)

    Devi, Naorem Bilasini; Srivastava, M P; Roy, Savita

    2010-01-01

    Plasma route to nanofabrication has drawn much attention recently. The dense plasma focus (DPF) device is used for depositing aluminium nanoparticles on n-type Si (111) wafer. The plasma chamber is filled with argon gas and evacuated at a pressure of 80 Pa. The substrate is placed at distances 4.0 cm, 5.0 cm and 6.0 cm from the top of the central anode. The aluminium is deposited on Si wafer at room temperature with two focused DPF shots. The deposits on the substrate are examined for their morphological properties using atomic force microscopy (AFM). The AFM images have shown the formation of aluminium nanoparticles. From the AFM images, it is found that the size of aluminium nanoparticles increases with increase in distance between the top of anode and the substrate for same number of DPF shots.

  19. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. Copyright © 2015 Elsevier Inc. All rights reserved.

  20. Aluminium Roofing Products Ltd Marketing to the Public Sector, UK

    OpenAIRE

    Hosseini, Sadaf

    2009-01-01

    This management project was undertaken on behalf of Aluminium Roofing Products Ltd ™ (ARP), a young, entrepreneurial company associated predominantly with aluminium products. The project brief was initially untaken by Ian Dunbar - one of the marketing segmentation gurus in the UK. As a result of his investigation, the company aimed to target the public sector in the UK in order to increase their market share. The project was fairly broad and identified several areas of the public sector which...

  1. Adhesive Bonding of Aluminium Alloy A5754 by Epoxy Resins

    Directory of Open Access Journals (Sweden)

    Ivan Michalec

    2013-01-01

    Full Text Available Joining thin sheets of aluminium and its alloys is a promising area in the field of joining materials. Nowadays, joining methods that do not melt the material itself are increasingly being utilised. This paper deals with adhesive bonding of aluminium alloy A5754 by two-component epoxy resins. Theresults show that joints bonded by Hysol 9466 have appropriate mechanical properties, but that joints bonded by Hysol 9492 have better thermal stability.

  2. Numerical Modelling of Drawbeads for Forming of Aluminium Alloys

    OpenAIRE

    Joshi, Y; Christiansen, Peter; Masters, I; Bay, Niels Oluf; Dashwood, R

    2016-01-01

    The drawbeads in stamping tools are usually designed based on experience from the forming of steel. However, aluminium alloys display different forming behaviour to steels, which is not reflected in the drawbead design for tools used for stamping aluminium. This paper presents experimental results from different semi-circular drawbead geometries commonly encountered in automotive dies and compares them to those obtained from Stoughton’s analytical drawbead model and the 2D plane strain drawbe...

  3. Twenty years of isotope applications in the Hungarian aluminium industry

    International Nuclear Information System (INIS)

    Bujdoso, E.

    1982-01-01

    After a short review of the isotope techniques applied in the Hungarian aluminium industry some special applications and their results are briefly outlined. Industrial and laboratory scale trace constituent determinations, isotope and activation analytical methods and the application of sealed radiation sources are discussed. It has been shown that the related R+D activity followed closely the development trends of the aluminium industry. The references given is a comprehensive bibliography of Hungarian publications in this field. (author)

  4. Physiological Characterization of Kenyan Sorghum Lines for Tolerance To Aluminium

    OpenAIRE

    Cheprot, R. K.; Matonyei, T. K.; Maritim, K. K.; Were, B. A.; Dangasuk, O. G.; Onkware, A. O.; Gudu, S.

    2014-01-01

    Eighty nine Kenyan sorghum lines were screened for tolerance to aluminium toxicity in nutrient solution. Relative net root growth; root tip aluminium content and variation in organic acid exudation were used to determine the tolerance or sensitivity of the sorghum lines at 148 µM Al for six days. The lines showed variable reduction in root growth under the Al stress. On the basis of the relative net root growths, three lines were tolerant, nineteen were moderately tolerant and sixty seven wer...

  5. Influence of Chemical Composition on Porosity in Aluminium Alloys

    OpenAIRE

    Kucharčík L.; Brůna M.; Sládek A.

    2014-01-01

    Porosity is one of the major defects in aluminum castings, which results is a decrease of a mechanical properties. Porosity in aluminum alloys is caused by solidification shrinkage and gas segregation. The final amount of porosity in aluminium castings is mostly influenced by several factors, as amount of hydrogen in molten aluminium alloy, cooling rate, melt temperature, mold material, or solidification interval. This article deals with effect of chemical composition on porosity in Al-Si alu...

  6. Lake restoration with aluminium, bentonite and Phoslock: the effect on sediment stability and light attenuation

    DEFF Research Database (Denmark)

    Egemose, Sara; Reitzel, Kasper; Flindt, Mogens

    treatments on aluminium mobility, sediment stability or light climate. A laboratory flume experiment including three shallow Danish lakes was conducted. We measured the effects of aluminium, Phoslock (a commercial product), bentonite, and a combination of bentonite/aluminium. Each treatment caused a varying...... consolidation of the sediment. The largest consolidation occurred using Phoslock- and bentonite-addition followed by bentonite/aluminium-addition, whereas aluminium alone had no effect. Sediment stability thresholds were measured before and after addition. Especially Phoslock, but also bentonite and bentonite....../aluminium increased sediment erosion threshold, with respectively 200%, 43% and 57%. Aluminium, bentonite/aluminium, and Phoslock improved the light conditions in the water phase, with respectively 60%, 57% and 50%, whereas bentonite created higher turbidity. Conclusively aluminium improved the light conditions...

  7. The binding, transport and fate of aluminium in biological cells.

    Science.gov (United States)

    Exley, Christopher; Mold, Matthew J

    2015-04-01

    Aluminium is the most abundant metal in the Earth's crust and yet, paradoxically, it has no known biological function. Aluminium is biochemically reactive, it is simply that it is not required for any essential process in extant biota. There is evidence neither of element-specific nor evolutionarily conserved aluminium biochemistry. This means that there are no ligands or chaperones which are specific to its transport, there are no transporters or channels to selectively facilitate its passage across membranes, there are no intracellular storage proteins to aid its cellular homeostasis and there are no pathways which evolved to enable the metabolism and excretion of aluminium. Of course, aluminium is found in every compartment of every cell of every organism, from virus through to Man. Herein we have investigated each of the 'silent' pathways and metabolic events which together constitute a form of aluminium homeostasis in biota, identifying and evaluating as far as is possible what is known and, equally importantly, what is unknown about its uptake, transport, storage and excretion. Copyright © 2014 Elsevier GmbH. All rights reserved.

  8. Effect of iron and silicon in aluminium and its alloys

    International Nuclear Information System (INIS)

    Kovacs, I.

    1990-01-01

    The iron and silicon are the main impurities in aluminium, they are always present in alloys made from commercially pure base material. The solid solubility of iron in aluminium is very low, therefore its largest amount forms intermetallic compounds the kind of which depends strongly on the other impurities of alloying elements. Although the solid solubility of silicon is much larger than that of the iron, it is the constituent of both the primary and the secondary particles, the structure of which depends in general on the iron-silicon concentration ratio. These Fe and Si containing particles can cause various and basic changes in the macroscopic properties of the alloy. Since commercially pure aluminium has extensive consumer and industrial use, it is very important to know, not only from scientific but also from practical point of view, the effect of iron and silicon on the physical and mechanical properties of aluminium and its alloys. The aim of the ''International Workshop on the Effect of Iron and Silicon in Aluminium and its Alloys'' was to clarify the present knowledge on this subject. The thirty papers presented at the Workshop and collected in this Proceedings cover many important fields of the subject. I hope that they will contribute to both the deeper understanding of the related phenomena and the improvement of technologies for producing better aluminium alloys

  9. Compressive Behaviour and Energy Absorption of Aluminium Foam Sandwich

    Science.gov (United States)

    Endut, N. A.; Hazza, M. H. F. Al; Sidek, A. A.; Adesta, E. T. Y.; Ibrahim, N. A.

    2018-01-01

    Development of materials in automotive industries plays an important role in order to retain the safety, performance and cost. Metal foams are one of the idea to evolve new material in automotive industries since it can absorb energy when it deformed and good for crash management. Recently, new technology had been introduced to replace metallic foam by using aluminium foam sandwich (AFS) due to lightweight and high energy absorption behaviour. Therefore, this paper provides reliable data that can be used to analyze the energy absorption behaviour of aluminium foam sandwich by conducting experimental work which is compression test. Six experiments of the compression test were carried out to analyze the stress-strain relationship in terms of energy absorption behavior. The effects of input variables include varying the thickness of aluminium foam core and aluminium sheets on energy absorption behavior were evaluated comprehensively. Stress-strain relationship curves was used for energy absorption of aluminium foam sandwich calculation. The result highlights that the energy absorption of aluminium foam sandwich increases from 12.74 J to 64.42 J respectively with increasing the foam and skin thickness.

  10. Surface roughness when diamond turning RSA 905 optical aluminium

    Science.gov (United States)

    Otieno, T.; Abou-El-Hossein, K.; Hsu, W. Y.; Cheng, Y. C.; Mkoko, Z.

    2015-08-01

    Ultra-high precision machining is used intensively in the photonics industry for the production of various optical components. Aluminium alloys have proven to be advantageous and are most commonly used over other materials to make various optical components. Recently, the increasing demand from optical systems for optical aluminium with consistent material properties has led to the development of newly modified grades of aluminium alloys produced by rapid solidification in the foundry process. These new aluminium grades are characterised by their finer microstructures and refined mechanical and physical properties. However the machining database of these new optical aluminium grades is limited and more research is still required to investigate their machinability performance when they are diamond turned in ultrahigh precision manufacturing environment. This work investigates the machinability of rapidly solidified aluminium RSA 905 by varying a number of diamond-turning cutting parameters and measuring the surface roughness over a cutting distance of 4 km. The machining parameters varied in this study were the cutting speed, feed rate and depth of cut. The results showed a common trend of decrease in surface roughness with increasing cutting distance. The lowest surface roughness Ra result obtained after 4 km in this study was 3.2 nm. This roughness values was achieved using a cutting speed of 1750 rpm, feed rate of 5 mm/min and depth of cut equal to 25 μm.

  11. Investigation of different anode materials for aluminium rechargeable batteries

    Science.gov (United States)

    Muñoz-Torrero, David; Leung, Puiki; García-Quismondo, Enrique; Ventosa, Edgar; Anderson, Marc; Palma, Jesús; Marcilla, Rebeca

    2018-01-01

    In order to shed some light into the importance of the anodic reaction in reversible aluminium batteries, we investigate here the electrodeposition of aluminium in an ionic liquid electrolyte (BMImCl-AlCl3) using different substrates. We explore the influence of the type of anodic material (aluminium, stainless steel and carbon) and its 3D geometry on the reversibility of the anodic reaction by cyclic voltammetry (CV) and galvanostatic charge-discharge. The shape of the CVs confirms that electrodeposition of aluminium was feasible in the three materials but the highest peak currents and smallest peak separation in the CV of the aluminium anode suggested that this material was the most promising. Interestingly, carbon-based substrates appeared as an interesting alternative due to the high peak currents in CV, moderate overpotentials and dual role as anode and cathode. 3D substrates such as fiber-based carbon paper and aluminium mesh showed significantly smaller overpotentials and higher efficiencies for Al reaction suggesting that the use of 3D substrates in full batteries might result in enhanced power. This is corroborated by polarization testing of full Al-batteries.

  12. Effects of Aluminium Sulfate on Cadmium Accumulation in Rice

    International Nuclear Information System (INIS)

    Khamvarn, Vararas; Boontanon, Narin; Prapagdee, Benjaphorn; Kumsopa, Acharaporn; Boonsirichai, Kanokporn

    2011-06-01

    Full text: Cadmium accumulation in Pathum Thani 1 and Suphan Buri 60 rice cultivars was investigated upon treatment with aluminium sulfate as a precipitant. Rice was grown hydroponically in a medium containing 4 ppm cadmium nitrate with or without 4 ppm aluminium sulfate. Root, stem with leaves and grain samples were collected and analyzed for cadmium content using atomic absorption spectroscopy and inductively coupled plasma atomic emission spectroscopy. Without the addition of aluminium sulfate, Pathum Thani 1 and Suphan Buri 60 accumulated 24.71∫ 3.14 ppm and 34.43 ∫ 4.51 ppm (dry weight of whole plant) of cadmium, respectively. With aluminium sulfate, cadmium accumulation increased to 40.66 ∫ 2.47 ppm and 62.94 ∫ 10.69 ppm, respectively. The addition of aluminium sulfate to the planting medium did not reduce cadmium accumulation but caused the rice to accumulate more cadmium especially in the shoots and grains. This observation might serve as the basis for future research on the management of agricultural areas that are contaminated with cadmium and aluminium

  13. Evaluating stress corrosion cracking behaviour of high strength AA7075-T651 aluminium alloy

    Science.gov (United States)

    Prabhuraj, P.; Rajakumar, S.; Lakshminarayanan, A. K.; Balasubramanian, V.

    2017-12-01

    The objective of the present study is to determine the threshold stress level of stress corrosion cracking (SCC) in AA7075-T651 aluminium alloy by suitable experimentation. The test was carried out using a circumferential notch specimen in a horizontal-type constant load SCC setup in a 3.5 wt.% NaCl solution. The time to failure by SCC was determined at various loading conditions. The threshold stress of AA7075-T651 alloy was found to be 242 MPa in a 3.5 wt.% NaCl solution. The various regions of the fractured surface specimen such as machined notch, SCC region and final overload fracture area were examined using scanning electron microscopy (SEM) in order to identify the SCC mechanism.

  14. Bioaccumulation of Aluminium in Hydromacrophytes in Polish Coastal Lakes

    Directory of Open Access Journals (Sweden)

    Senze Magdalena

    2015-03-01

    Full Text Available The research on aluminium content was conducted in water and on aquatic flora of Polish lakes in the central part of the coast. The study included the lakes Sarbsko, Choczewskie, Bia.e, K.odno, D.brze and Salino investigated in the summer of 2013. The examined lakes belong mainly to the direct basin of the Baltic Sea. Samples of aquatic plants and lake waters were collected. In the water samples pH and electrolytic conductivity were measured. The aluminium content was determined both in water and aquatic plants. Submerged hydromacrophyte studies included Myriophyllum alterniflorum L., Potamogeton perfoliatus L. and Ceratophyllum demersum L. Emergent hydromacrophyte studies included Phragmites australis (Cav. Trin. ex Steud., Juncus bulbosus L., Iris pseudacorus L., Eleocharis palustris (L. Roem. % Schult., Phalaris arundinacea L., Carex riparia Curt., Mentha aquatic L., Stratiotes aloides L., Alisma plantago-aquatica L., Glyceria maxima (Hartman Holmb., Sagittaria sagittifolia L., Scirpus lacustris L. and Typha angustifolia L. The purpose of this investigation was the determination of the aluminium content in submerged and emergent hydromacrophytes and also the definition of their bioaccumulative abilities. The average concentration of aluminium in water was 2.68 fęg Al dm.3. The average content of aluminium in plants was 2.8015 mg Al kg.1. The bioaccumulation factor ranged from BCF=19.74 to BCF=16619. On the basis of the analysis of the aluminium content in water and aquatic plants results show that both water and plants were characterized by a moderate level of aluminium. The recorded concentrations indicate a mid-range value and are much lower than those which are quoted for a variety of surface waters in various parts of the world.

  15. Accumulation and toxicity of aluminium-contaminated food in the freshwater crayfish, Pacifastacus leniusculus.

    Science.gov (United States)

    Woodburn, Katie; Walton, Rachel; McCrohan, Catherine; White, Keith

    2011-10-01

    The accumulation and toxicity of aluminium in freshwater organisms have primarily been examined following aqueous exposure. This study investigated the uptake, excretion and toxicity of aluminium when presented as aluminium-contaminated food. Adult Pacifastacus leniusculus were fed control (3 μg aluminium/g) or aluminium-spiked pellets (420 μg aluminium/g) over 28 days. Half the crayfish in each group were then killed and the remainder fed control pellets for a further 10 days (clearance period). Concentrations of aluminium plus the essential metals calcium, copper, potassium and sodium were measured in the gill, hepatopancreas, flexor muscle, antennal gland (kidney) and haemolymph. Histopathological analysis of tissue damage and sub-cellular distribution of aluminium were examined in the hepatopancreas. Haemocyte number and protein concentration in the haemolymph were analysed as indicators of toxicity. The hepatopancreas of aluminium-fed crayfish contained significantly more aluminium than controls on days 28 and 38, and this amount was positively correlated with the amount ingested. More than 50% of the aluminium in the hepatopancreas of aluminium-fed crayfish was located in sub-cellular fractions thought to be involved in metal detoxification. Aluminium concentrations were also high in the antennal glands of aluminium-fed crayfish suggesting that some of the aluminium lost from the hepatopancreas is excreted. Aluminium exposure via contaminated food caused inflammation in the hepatopancreas but did not affect the number of circulating haemocytes, haemolymph ion concentrations or protein levels. In conclusion, crayfish accumulate, store and excrete aluminium from contaminated food with only localised toxicity. Copyright © 2011 Elsevier B.V. All rights reserved.

  16. SUPERPLASTIC BEHAVIOUR IN DYNAMICALLY RECRYSTALLISING ALUMINIUM ALLOYS

    Directory of Open Access Journals (Sweden)

    R AMICHI

    1999-12-01

    Full Text Available Aluminium alloys can be thermomechanically processed to develop the grain fine microstructures required for superplasticity by either static recrystallisation prior to superplastic forming (SPF or by dynamic recrystallisation during the early stages of deformation. The present work has examined and compared the superplastic behaviour and the microstructural evolution in Al-Li alloys (8090 sheet material processed by the second route for a wide range of temperatures and strain-rates.  It was observed that the material showed a high potential for superplastic flow. Although significant superplasticity was observed at temperature of 400°C and below. The reasons for the high resistance of the material to strain localisation are discussed.  It was noted that ductility enhancement could also be achieved by the control of the strain-rate path. A rapid pre-strain improved significantly the subsequent superplastic elongation to failure at optimum strain rate.  Further enhancement has been obtained by pre-straining at constant velocity following by deformation to failure at lower constant velocity. The microstructure changes prior or during deformation were also examined.

  17. Methemoglobinemia in aluminium phosphide poisoning in rats.

    Science.gov (United States)

    Lall, S B; Peshin, S S; Mitra, S

    2000-01-01

    Aluminium phosphide (AlP) a grain fumigant is the leading cause of intentional poisoning in North India. The mechanisms involved in toxicity are not known and there is no antidote till date. The present study was carried out to investigate the oxygen free radical generation, methemoglobinemia and effect of methylene blue treatment on survival time in rat model of AlP poisoning. AlP (50 mg/kg, intragastric) was administered in one group and the other group received AlP + Methylene Blue (MB) (0.1%, 1 mg/kg/5 min, i.v.). Malonyldialdehyde (MDA) and methemoglobin (MeHb) levels were measured at 10 and 30 min intervals. Blood MDA levels increased at 10 and 30 min after AlP exposure with simultaneous rise in MeHb levels suggesting methemoglobinemia could be due to increased oxygen free radical generation. Methylene blue caused a significant fall in both the parameters with prolongation of survival time. It is concluded that AlP causes methemoglobinemia responding to methylene blue treatment.

  18. Acute aluminium phosphide poisoning, what is new?

    Directory of Open Access Journals (Sweden)

    Yatendra Singh

    2014-01-01

    Full Text Available Aluminium phosphide (AlP is a cheap solid fumigant and a highly toxic pesticide that is commonly used for grain preservation. AlP has currently generated interest with increasing number of cases in the past four decades because of its increased use for agricultural and nonagricultural purposes, and also its easy availability in the markets has led to its increased misuse to commit suicide. Ingestion is usually suicidal in intent, uncommonly accidental and rarely homicidal. The poison affects all systems, shock, cardiac arrhythmias with varied ECG changes and gastrointestinal features being the most prominent. Diagnosis is made on the basis of clinical suspicion, a positive silver nitrate paper test to phosphine, and gastric aspirate and viscera biochemistry. Treatment includes early gastric lavage with potassium permanganate or a combination of coconut oil and sodium bicarbonate, administration of charcoal and palliative care. Specific therapy includes intravenous magnesium sulphate and oral coconut oil. Unfortunately, the lack of a specific antidote Results in very high mortality and the key to treatment lies in rapid decontamination and institution of resuscitative measures. This article aims to identify the salient features and mechanism of AlP poisoning along with its management strategies and prognostic variables.

  19. Design of Grain Refiners for Aluminium Alloys

    Science.gov (United States)

    Tronche, A.; Greer, A. L.

    The efficiency of a grain refiner can be quantified as the number of grains per nucleant particle in the solidified product. Even for effective refiners in aluminium, such as Al-5Ti-1B, it is known from experiments that efficiencies are very low, at best 10-3 to 102. It is of interest to explore the reasons for such low values, and to assess the prospects for increased efficiency though design of refiners. Recently it has been shown [1] that a simple recalescence-based model can make quantitative predictions of grain size as a function of refiner addition level, cooling rate and solute content. In the model, the initiation of grains is limited by the free growth from nucleant particles, the size distribution of which is very important. The present work uses this model as the basis for discussing the effect of particle size distribution on grain refiner performance. Larger particles (of TiB2 in the case of present interest) promote greater efficiency, as do narrower size distributions. It is shown that even if the size distribution could be exactly specified, compromises would have to be made to balance efficiency (defined as above) with other desirable characteristics of a refiner.

  20. Fabrication experience of aluminium clad aluminium matrix dispersion fuels at BARC

    International Nuclear Information System (INIS)

    Ganguly, C.; Hedge, P.W.; Prasad, G.J.

    1995-01-01

    Aluminium clad, aluminium matrix plate type dispersion fuels have been fabricated in BARC in recent years as part of fuel development programme for small non-power research reactors. The present paper describes the flowsheet developed for fabrication of Al-UAl x , Al-U 3 Si 2 and Al-U 3 O 8 fuels at BARC. The Al-20% U alloy fuel for KAMINI neutron radiography reactor was prepared by 'melting and casting' route, followed by picture framing and roll-bonding. For higher 'U' density fuels namely, Al-UAl x , Al-U 3 O 8 and Al-U 3 Si 2 the 'powder metallurgy' route was followed for preparation of fuel meat. The novel features in fabrication route were: addition of Zr for stabilizing UAl 3 phase in Al-20% U alloy; x-ray radiography and microdensitometric scanning of radiographs for location of fuel outline inside fuel element and for confirming homogeneous distribution of fissile atoms; immersion ultrasonic testing for confirming good bonding between mating Al surface of the fuel plate. (author)

  1. Aluminium Matrix Composites Reinforced with Co-continuous Interlaced Phases Aluminium-alumina Needles

    Directory of Open Access Journals (Sweden)

    Elvio de Napole Gregolin

    2002-09-01

    Full Text Available An Al-5SiO2 (5 wt% of SiO2 aluminium matrix fiber composite was produced where the reinforcement consists of fossil silica fibers needles. After being heat-treated at 600 °C, the original fiber morphology was retained but its microstructure changed from solid silica to an interconnected (Al-Si/Al2O3 interlaced structure named co-continuous composite. A technique of powder metallurgy, using commercial aluminium powder and the silica fibers as starting materials, followed by hot extrusion, was used to produce the composite. The co-continuous microstructure was obtained partially or totally on the fibers as a result of the reaction, which occurs during the heat treatment, first by solid diffusion and finally by the liquid Al-Si in local equilibrium, formed with the silicon released by reaction. The internal structure of the fibers was characterized using field emission electron microscope (FEG-SEM and optical microscopy on polished and fractured samples.

  2. Microstructure and properties of aluminium-aluminium oxide graded composite materials

    Science.gov (United States)

    Kamaruzaman, F. F.; Nuruzzaman, D. M.; Ismail, N. M.; Hamedon, Z.; Iqbal, A. K. M. A.; Azhari, A.

    2018-03-01

    In this research works, four-layered aluminium-aluminium oxide (Al-Al2O3) graded composite materials were fabricated using powder metallurgy (PM) method. In processing, metal-ceramic graded composite materials of 0%, 10%, 20% and 30% weight percentage of ceramic concentration were prepared under 30 ton compaction load using a cylindrical die-punch set made of steel. After that, two-step pressureless sintering was carried out at sintering temperature and time 600°C and 3 hours respectively. It was observed that the sintered cylindrical specimens of 30 mm diameter were prepared successfully. The graded composite specimens were analysed and the properties such as density, microstructure and hardness were measured. It was found that after sintering process, the diameter of the graded cylindrical structure was decreased. Using both Archimedes method and rule of mixture (ROM), he density of structure was measured. The obtained results revealed that the microvickers hardness was increased as the ceramic component increases in the graded layer. Moreover, it was observed that the interface of the graded structure is clearly distinguished within the multilayer stack and the ceramic particles are almost uniformly distributed in the Al matrix.

  3. Aluminium concentration versus the base cation to aluminium ratio as predictors for aluminium toxicity in Pinus sylvestris and Picea abies seedlings

    NARCIS (Netherlands)

    Schöll, van L.; Keltjens, W.G.; Hoffland, E.; Breemen, van N.

    2004-01-01

    Aluminium (Al) toxicity is considered an important factor in forest deterioration caused by soil acidification. A ratio of base cations (BC) to Al in the soil solution lower than 1 is widely used as an indicator for potentially adverse effects on tree health. In our view, the validity of the

  4. Photodynamic effect of aluminium and zinc tetrasulfophthalocyanines on melanoma cancer cells

    CSIR Research Space (South Africa)

    Maduray, K

    2010-06-01

    Full Text Available Aluminium and zinc tetrasulfophthalocyanines were activated with a 672nm wavelength laser to investigate the photodynamic effects on melanoma cancer, dermal fibroblast and epidermal keratinocyte cells. Aluminium tetrasulfophthalocyanine was more...

  5. AE Monitoring of Diamond Turned Rapidly Soldified Aluminium 443

    International Nuclear Information System (INIS)

    Onwuka, G; Abou-El-Hossein, K; Mkoko, Z

    2017-01-01

    The fast replacement of conventional aluminium with rapidly solidified aluminium alloys has become a noticeable trend in the current manufacturing industries involved in the production of optics and optical molding inserts. This is as a result of the improved performance and durability of rapidly solidified aluminium alloys when compared to conventional aluminium. Melt spinning process is vital for manufacturing rapidly solidified aluminium alloys like RSA 905, RSA 6061 and RSA 443 which are common in the industries today. RSA 443 is a newly developed alloy with few research findings and huge research potential. There is no available literature focused on monitoring the machining of RSA 443 alloys. In this research, Acoustic Emission sensing technique was applied to monitor the single point diamond turning of RSA 443 on an ultrahigh precision lathe machine. The machining process was carried out after careful selection of feed, speed and depths of cut. The monitoring process was achieved with a high sampling data acquisition system using different tools while concurrent measurement of the surface roughness and tool wear were initiated after covering a total feed distance of 13km. An increasing trend of raw AE spikes and peak to peak signal were observed with an increase in the surface roughness and tool wear values. Hence, acoustic emission sensing technique proves to be an effective monitoring method for the machining of RSA 443 alloy. (paper)

  6. The structure of high-quality aluminium cast iron

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2012-01-01

    Full Text Available In this study presents the analyse of aluminium iron cast structure (as-cast condition which are used in high temperature. While producing the casts of aluminium iron major influence has been preserve the structure of technological process parameters. The addition to Fe-C-Al alloy V, Ti, Cr leads to the improvement of functional and mechanical cast qualities. In this study, a method was investigated to eliminate the presence of undesirable Al4C3 phases in a aluminium cast iron structure and thus improve the production process. V and Ti additions in aluminium cast iron allows to development of FeAl - VC or TiC alloys. In particular, V or Ti contents above 5 wt.% were found to totally eliminate the presence of Al4C3. In addition, preliminary work indicates that the alloy with the FeAl - VC or TiC structure reveals high oxidation resistance. The introduction of 5 wt.% chromium to aluminium cast iron strengthened Al4C3 precipitate. Thus, the resultant alloy can be considered an intermetallic FeAl matrix strengthened by VC and TiC or modified Al4C3 reinforcements.

  7. Aluminium Foams in the Design of Transport Means

    Directory of Open Access Journals (Sweden)

    Krešimir Grilec

    2012-07-01

    Full Text Available The requirements for weight reduction and improvement of performances in the design of transport means are often in contradiction to the requirements for increased safety. One of the possible ways of meeting these requirements is the application of metal foams. Thanks to cellular structure of aluminium foam along with low weight, the capability of noise and vibration damping, they feature also excellent capabilities of absorbing impact energy. Their application in the production of impact-sensitive elements of mobile or stationary transport means has significantly contributed to the reduction of the impact or collision consequences.The focus of this paper is on improving the energy absorption characteristics of aluminium foams considering the significance of their application for the technology of traffic and transport.The paper analyzes the influence of the chemical composition and density on the compression behaviour of aluminium foam. The aluminium foam samples were produced from Alulight precursor. The capability of samples to absorb mechanical energy has been estimated according to the results of compression tests. The tests were performed on a universal test machine. The test results showed that aluminium foams feature good energy absorption and the absorption capability decreases with the foam density. The Alulight AlMgSi 0.6 TiH2 - 0.4 foam can absorb more energy than Alulight AlSi 10 TiH2 – 0.8 foam.

  8. Impact properties of aluminium - glass fiber reinforced plastics sandwich panels

    Directory of Open Access Journals (Sweden)

    Mathivanan Periasamy

    2012-06-01

    Full Text Available Aluminium - glass fiber reinforced plastics (GFRP sandwich panels are hybrid laminates consisting of GFRP bonded with thin aluminum sheets on either side. Such sandwich materials are increasingly used in airplane and automobile structures. Laminates with varying aluminium thickness fractions, fiber volume fractions and orientation in the layers of GFRP were fabricated by hand lay up method and evaluated for their impact performance by conducting drop weight tests under low velocity impacts. The impact energy required for initiating a crack in the outer aluminium layer as well as the energy required for perforation was recorded. The impact load-time history was also recorded to understand the failure behavior. The damage depth and the damage area were measured to evaluate the impact resistance. Optical photography and scanning electron micrographs were taken to visualize the crack and the damage zone. The bidirectional cross-ply hybrid laminate (CPHL has been found to exhibit better impact performance and damage resistance than the unidirectional hybrid laminate (UDHL. Increase in aluminium thickness fraction (Al tf and fiber volume fraction (Vf resulted in an increase in the impact energy required for cracking and perforation. On an overall basis, the sandwich panels exhibited better impact performance than the monolithic aluminium.

  9. Cancer risk among workers of a secondary aluminium smelter.

    Science.gov (United States)

    Maltseva, A; Serra, C; Kogevinas, M

    2016-07-01

    Cancer risk in secondary aluminium production is not well described. Workers in this industry are exposed to potentially carcinogenic agents from secondary smelters that reprocess aluminium scrap. To evaluate cancer risk in workers in a secondary aluminium plant in Spain. Retrospective cohort study of male workers employed at an aluminium secondary smelter (1960-92). Exposure histories and vital status through 2011 were obtained through personal interviews and hospital records, respectively. Standardized mortality (SMRs) and incidence ratios (SIRs) were calculated. The study group consisted of 98 workers. We found increased incidence and mortality from bladder cancer [SIR = 2.85, 95% confidence interval (CI) 1.23-5.62; SMR = 5.90, 95% CI 1.58-15.11]. Increased incidence was also observed for prostate cancer and all other cancers but neither were statistically significant. No increased risk was observed for lung cancer. Results of this study suggest that work at secondary aluminium smelters is associated with bladder cancer risk. Identification of occupational carcinogens in this industry is needed. © The Author 2016. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  10. Structure and selected properties of high-aluminium Zn alloy with silicon addition

    Directory of Open Access Journals (Sweden)

    A. Zyska

    2011-07-01

    Full Text Available The results of examinations concerning the abrasive wear resistance, hardness, and thermal expansion of high-aluminium zinc alloys are presented. The examinations were carried out for five synthetic ZnAl28 alloys with variable silicon content ranging from 0.5% to 3.5%, and – for the purpose of comparison – for the standardised ZnAl28Cu4 alloy. It was found that silicon efficiently increases the tribological properties and decreases the coefficient of thermal expansion of zinc alloys. The most advantageous set of the examined properties is exhibited by the alloys containing over 2.5% Si. They are characterised by higher parameters as compared with the standardised alloy. Observations of microstructures reveal that silicon precipitates as a separate compact phase, and its morphology depends on t he Si content in the alloy. The performed examinations show that silicon can satisfactorily replace copper in high aluminium Zn alloys, thus eliminating the problem of dimensional instability of castings.

  11. Radiographic and ultrasonic testings of welded joints of 6063 aluminium alloy

    International Nuclear Information System (INIS)

    Oliveira e Silva Mury, A.G. de.

    1980-05-01

    A study on evaluation of weld defects in aluminium butt joints was made in a comparative way through the radiographic and ultrasonic testing. This work was conducted with pipes 5 IPS (6,35 mm thickness) of 6063 aluminium alloy, circumferential TIG welded, due to the difficulty on performing non-destructive testing with this schedule. It was concluded thta ultrasonic testing has adequate sensitivity when setting gain adjustment is made with aid of a reference curve constructed by using a Reference Block (among others studied) with 1,5 mm dia. Hole as reference reflector, and a 5 MHz angle beam search-unit. In this case the ultrasonic testing is more accurate than radiographic testing to detect planar defects like lack of fusion and lack of penetration. Defect sizing by ultrasonic methods employed were 6 and 20 dB drop methods. In spite of your observed limitations concerning the establishment of the real size of defects, the procedure applied was precise for locate and define the weld defects that where found in this study. (author) [pt

  12. Flow injection spectrophotometry using natural reagent from Morinda citrifolia root for determination of aluminium in tea.

    Science.gov (United States)

    Tontrong, Sopa; Khonyoung, Supada; Jakmunee, Jaroon

    2012-05-01

    A flow injection (FI) spectrophotometric method with using natural reagent extracted from Morinda citrifolia root has been developed for determination of aluminium. The extract contained anthraquinone compounds which could react with Al(3+) to form reddish complexes which had maximum absorption wavelength at 499.0nm. The extract could be used as a reagent in FI system without further purification to obtain pure compound. A sensitive method for determination of aluminium in concentration range of 0.1-1.0mgL(-1), with detection limit of 0.05mgL(-1) was achieved. Relative standard deviations of 1.2% and 1.7% were obtained for the determination of 0.1 and 0.6mgL(-1) Al(3+) (n=11). Sample throughput of 35h(-1) was achieved with the consumption of 3mL each of carrier and reagent solutions per injection. The developed method was successfully applied to tea samples, validated by the FAAS standard method. The method is simple, fast, economical and could be classified as a greener analytical method. Copyright © 2011 Elsevier Ltd. All rights reserved.

  13. Investigation on the Mechanical and Tribological Properties of Aluminium-Tin Based Plain Bearing Material

    Directory of Open Access Journals (Sweden)

    T. Rameshkumar

    2010-06-01

    Full Text Available The purpose of this study is to investigate the Mechanical and Tribological properties of plain bearing alloys used especially in internal combustion engines. The mechanical properties namely Tensile strength and Hardness were investigated according to standard procedure. The sliding friction and wear properties of aluminium-tin alloy against high carbon high chromium steel were investigated at different normal loads as (29.43 N, 33.35 N and 36.25 N. Tests were carried in oil lubricated conditions with a sliding speed of 1 m/s. Prior to experimentation, the circulating engine oil 20w40 was heated to temperature of 800C using heater. The frictional behavior and wear property of aluminium-tin alloy were studied by means of pin-on-disk tribometer. The weight loss of the specimen was measured and wear and friction characteristics were calculated with respect to time, depth of wear track, sliding speed and bearing load. To determine the wear mechanism, the worn surfaces of the samples were examined using Scanning Electron Microscope (SEM. The optimum wear reduction was obtained at different normal loads and at same sliding speed.

  14. Determination of aluminium in groundwater samples by GF-AAS, ICP-AES, ICP-MS and modelling of inorganic aluminium complexes.

    Science.gov (United States)

    Frankowski, Marcin; Zioła-Frankowska, Anetta; Kurzyca, Iwona; Novotný, Karel; Vaculovič, Tomas; Kanický, Viktor; Siepak, Marcin; Siepak, Jerzy

    2011-11-01

    The paper presents the results of aluminium determinations in ground water samples of the Miocene aquifer from the area of the city of Poznań (Poland). The determined aluminium content amounted from aluminium determinations were performed using three analytical techniques: graphite furnace atomic absorption spectrometry (GF-AAS), inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). The results of aluminium determinations in groundwater samples for particular analytical techniques were compared. The results were used to identify the ascent of ground water from the Mesozoic aquifer to the Miocene aquifer in the area of the fault graben. Using the Mineql+ program, the modelling of the occurrence of aluminium and the following aluminium complexes: hydroxy, with fluorides and sulphates was performed. The paper presents the results of aluminium determinations in ground water using different analytical techniques as well as the chemical modelling in the Mineql+ program, which was performed for the first time and which enabled the identification of aluminium complexes in the investigated samples. The study confirms the occurrence of aluminium hydroxy complexes and aluminium fluoride complexes in the analysed groundwater samples. Despite the dominance of sulphates and organic matter in the sample, major participation of the complexes with these ligands was not stated based on the modelling.

  15. IEC 61267: Feasibility of type 1100 aluminium and a copper/aluminium combination for RQA beam qualities.

    Science.gov (United States)

    Leong, David L; Rainford, Louise; Zhao, Wei; Brennan, Patrick C

    2016-01-01

    In the course of performance acceptance testing, benchmarking or quality control of X-ray imaging systems, it is sometimes necessary to harden the X-ray beam spectrum. IEC 61267 specifies materials and methods to accomplish beam hardening and, unfortunately, requires the use of 99.9% pure aluminium (Alloy 1190) for the RQA beam quality, which is expensive and difficult to obtain. Less expensive and more readily available filters, such as Alloy 1100 (99.0% pure) aluminium and copper/aluminium combinations, have been used clinically to produce RQA series without rigorous scientific investigation to support their use. In this paper, simulation and experimental methods are developed to determine the differences in beam quality using Alloy 1190 and Alloy 1100. Additional simulation investigated copper/aluminium combinations to produce RQA5 and outputs from this simulation are verified with laboratory tests using different filter samples. The results of the study demonstrate that although Alloy 1100 produces a harder beam spectrum compared to Alloy 1190, it is a reasonable substitute. A combination filter of 0.5 mm copper and 2 mm aluminium produced a spectrum closer to that of Alloy 1190 than Alloy 1100 with the added benefits of lower exposures and lower batch variability. Copyright © 2015 Associazione Italiana di Fisica Medica. Published by Elsevier Ltd. All rights reserved.

  16. Fire design of aluminium structures according to Eurocode 9; Part 1-2

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.

    2007-01-01

    There is a tendency to use aluminium as structural material in heavily loaded structures. In a number of these structures, the resistance to fire should be considered in the structural design. Because of the low melting temperature of aluminium, aluminium structures are sensitive to fire and extra

  17. Light-weight aluminium bridges and bridge decks. An overview of recent applications

    NARCIS (Netherlands)

    Maljaars, J.; Soetens, F.; Kluyver, D. de

    2008-01-01

    The last decades have shown a large increase in the application of aluminium alloys for light-weight bridges. For bridge construction, aluminium alloys have some specific advantages, but also some points of attention. This paper deals with some recent projects of aluminium bridges, and for these

  18. Structural perturbation of diphtheria toxoid upon adsorption to aluminium hydroxide adjuvant

    NARCIS (Netherlands)

    Regnier, M.; Metz, B.; Tilstra, W.; Hendriksen, C.; Jiskoot, W.; Norde, W.; Kersten, G.

    2012-01-01

    Aluminium-containing adjuvants are often used to enhance the potency of vaccines. In the present work we studied whether adsorption of diphtheria toxoid to colloidal aluminium hydroxide induces conformational changes of the antigen. Diphtheria toxoid has a high affinity for the aluminium hydroxide

  19. PEMBINAAN PENGERAJIN BOKOR ALUMINIUM DI DESA MENYALI

    Directory of Open Access Journals (Sweden)

    I NYOMAN GDE ANTARA, dkk.

    2014-04-01

    Full Text Available Alluminium bowl craft industrial center is located in Menyali village Sawan district Buleleng regency of Bali province. In this business development, they faced some problems such as increasingly expensive alluminium plate raw materials, decreasing selling product prices due to competition among craftsmen, difficulty in extending the marketing, lack of capital, lack of knowledge in business management, and lack of technical capacity and production innovation. Currently the organization has been formed aluminum bowl craftsmen groups, they are “Sumber Urip” and “Sumur Jaya”. This organization is still limited to tradisional associations such as a community organization, has not led to organize in a micro-enterprise or cooperation. Their organization management should not be arranged. Therefore, they need helps from the government and other institutions to build this bowl craftsmen in developing their businesses through a group of micro-enterprises or cooperations. Wishly, with formal business entity that would facilitate access to a variety of coaching and help governments andother institutions. From the SWOT analysis, it is found some problems and solutions that should be done. Alluminium bowl craftsmen groups, named “Sumber Urip” and “Sumur Jaya” is not in the form of business entity or cooperation yet, so that the results of coaching have agreed to form a cooperation. Venture capital assistance for the development and production are still needed and to be an absolute given, but a way to market more absolute yield is given, through participation in various events exhibition to introduce the product is expected to expandits market share up to overseas or exports. In the production process it has been introduced that is appropriate technology for instant a rolling tool to make a wiring groove on the outside of the bowl, so that it will simplify and speed up the process, especially by aged mothers.Keywords: aluminium bowl, Menyali

  20. Behaviour of painted aluminium in Ibero-American atmosphere

    International Nuclear Information System (INIS)

    Morcillo, M.; Simancas, J.; Corvo, F.; Rosales, B.; Fragata, F.; Pena, J.; Sanchez, M.; Flores, S.; Almeida, E.; Rivero, S.; Rincon, O. T. de

    2003-01-01

    Aluminium generally presents good corrosion resistance to the atmosphere. However, unprotected aluminium and aluminium alloys weather outdoors to an ugly grey colour, which deepens to black in industrial atmospheres, and undergo superficial pitting in marine atmospheres, etc. Finishing technologies are applied for their protection and decoration in a wide range of applications. These technologies basically consist of two protection processes: anodizing and painting: the latter going from conventional solvent base paints to modern water-born, high solids and powder coatings. This paper considers the weathering performance of three paint systems: alkyl, polyurethane and polyester, after more than three years of exposure in a wide spectra of Ibero-American atmospheric conditions. The information reported includes resistance to undercutting corrosion at the scribe, filiform corrosion, fungal attack and change in the physico-chemical properties of the paint surface (loss of gloss, colour changes, chalking, etc.). (Author) 9 refs

  1. Application of Anodization Process for Cast Aluminium Surface Properties Enhancement

    Directory of Open Access Journals (Sweden)

    Włodarczyk-Fligier A.

    2016-09-01

    Full Text Available An huge interest is observed in last years in metal matrix composite, mostly light metal based, which have found their applications in many industry branches, among others in the aircraft industry, automotive-, and armaments ones, as well as in electrical engineering and electronics, where one of the most important issue is related to the corrosion resistance, especially on the surface layer of the used aluminium alloys. This elaboration presents the influence of ceramic phase on the corrosion resistance, quality of the surface layer its thickness and structure of an anodic layer formed on aluminium alloys. As test materials it was applied the aluminium alloys Al-Si-Cu and Al-Cu-Mg, for which heat treatment processes and corrosion tests were carried out. It was presented herein grindability test results and metallographic examination, as well. Hardness of the treated alloys with those ones subjected to corrosion process were compared.

  2. Optically Designed Anodised Aluminium Surfaces: Microstructural and Electrochemical Aspects

    DEFF Research Database (Denmark)

    Gudla, Visweswara Chakravarthy

    was studied in-situ in a transmission electron microscope and also ex-situ using grazing incidence X-ray diffraction. The Al-Metal oxide surface composites based on TiO2, Y2O3, and CeO2 prepared by friction stir processing were employed to generate light scattering anodised surfaces by embedding oxide...... industry. Conventional colouring techniques applied to anodised aluminium surfaces cannot generate glossy white appearing surfaces due to the fundamental differences in the interaction with visible light that is required. Surfaces appearing as perfect white are due to the scattering of visible light......This thesis presents the research work aimed at generating anodised aluminium surfaces with bright, white, and glossy decorative appearance. The aluminium surface finishing industry has been on the lookout for such surfaces due to their potential applications in aerospace, architecture, and design...

  3. Comparative performance of aluminium copper and iron solar stills

    International Nuclear Information System (INIS)

    Dioha, I.J.; Nwagbo, E.E.; Gulma, N.A.

    1990-12-01

    Three different metal sheets have been used in the fabrication of three different single sloping solar stills of the same surface geometry. The metals were galvanized iron, aluminium and copper. This paper presents the performance of the different stills operating under the same environmental conditions. The observed distillate yields was greatest for copper, then aluminium and lastly, iron still. The differences in the yields is attributed to the differences in the thermal conductivities of the metals. The equivalent local costs for the fabrication of the copper, aluminium and iron stills are respectively $160, $95 and $60. Taking the long run costs into consideration, the copper still is preferred because of its availability, durability, weldability and relatively higher conductivity of 380Wm -1 K -1 value. (author). 9 refs, 2 figs, 2 tabs

  4. Quantitative electron probe microanalysis of borides in aluminium

    International Nuclear Information System (INIS)

    Karduck, P.; Schuerhoff, H.J.; Burchard, W.G.

    1983-01-01

    A procedure for the quantitative analysis of borides in aluminium was introduced. For this purpose the optimal apparative boundary conditions for the EPMA of boron were worked out. With these conditions a satisfactory peak to background ratio of 57 could be achieved for B-Kα-radiation. By application of this method the following conclusion should be drawn concerning the kind of nuclei during grain refinement of aluminium with titanium and boron: For grain refinement of aluminium with titanium and boron in the hypoperitectic region of the binary system Al-Ti TiB 2 -particles in clusters provide the high efficiency of refinement. This entails that the TiB 2 -particles already present in the master alloy remain inert in the melt. Hence, the good efficiency of refinement in this region cannot be attributed to the presence of particles like Al 3 Ti, AlB 2 or (Al, Ti) B 2 . (Author)

  5. Aluminium supplier selection for the automotive parts manufacturer

    Directory of Open Access Journals (Sweden)

    M. Cieśla

    2016-04-01

    Full Text Available This paper presents a methodology for selection of the optimal sources of supply, which is also known as the problem of supplier selection. Theoretical considerations are expanded with research related to aluminium supplier selection for a hypothetical manufacturer of aluminium parts for transportation equipment located in Poland. Evaluation of five suppliers of aluminium from Poland, Germany and Slovenia has been conducted using a weighted scoring method, a strengths and weaknesses method and a graphical method. Choosing the best offer and prioritizing suppliers allows not only the most rational decision in the field of supply logistics to be taken but also the quality of service in the metallurgical industry to be improved.

  6. Simultaneous determination of aluminium and phosphorus by neutron activation analysis

    International Nuclear Information System (INIS)

    Gatschke, W.; Gawlik, D.

    1980-01-01

    With the use of the pneumatic tube system of the BER II reactor, the irradiation position of which is equipped with a movable cadmium shield, the aluminium and phosphorus levels in bone powder and in human bone biopsies were determined. The contribution of aluminium and phosphorus to the 28 Al activity could be separated mathematically after the samples had been irradiated with and without cadmium shielding. The sensitivity and limit of quantitative determination of the analytical procedure were determined using the addition method and the fact that the levels of each element measured was independent of the amount of the other element was proved. (author)

  7. Bioactive type glass-ceramics within incorporated aluminium

    International Nuclear Information System (INIS)

    Volzone, C.; Stabile, F.M.; Ortiga, J.

    2012-01-01

    Bioactive glass-ceramics are used as biomaterials for the reparation of bone tissue. They are prepared, generally, by bioglass of specific composition for each particular use. The aluminium addition in the formulation at very small quantities influences on the structural properties. Two glass-ceramics obtained by P 2 O 5 -Na 2 O-CaO-SiO 2 formulation within aluminium (0.5 % in Al 2 O 3 base) added through a reactive alumina and purified feldspar were analyzed. The results showed structural differences between both glass-ceramics. (author)

  8. Fatigue behaviour of GMAW welded aluminium alloy AA7020

    OpenAIRE

    Bloem, Carlos; Salvador Moya, Mª Dolores; Amigó, Vicente; Vicente-Escuder, Ángel

    2009-01-01

    [EN] The aim of this investigation is to evaluate the influence on fatigue behaviour of the finishing of the bulge in a welded aluminium zinc magnesium alloy AA7020. It was determined that total or partial elimination of the bulge has very little influence on its behaviour, giving a very similar result on both cases, where one is better than the other by only 3%. Bloem, C.; Salvador Moya, MD.; Amigó, V.; Vicente-Escuder, Á. (2009). Fatigue behaviour of GMAW welded aluminium alloy AA7020. W...

  9. Axillary hyperhidrosis treated with alcoholic solution of aluminium chloride hexahydrate.

    Science.gov (United States)

    Scholes, K T; Crow, K D; Ellis, J P; Harman, R R; Saihan, E M

    1978-01-01

    Sixty-five patients with axillary hyperhidrosis took part in a trial of treatment with a solution of 20% aluminium chloride hexahydrate in absolute alcohol, applied topically each night for a week and then whenever the patient thought it necessary. Excellent control of sweating was achieved in 64 patients, and occlusion of the area was found to be unnecessary. No troublesome side effects were reported. The results of this study indicate that 20% aluminium chloride hexahydrate in absolute alcohol is the treatment of first choice for patients with axillary hyperhidrosis. PMID:667571

  10. Transport phenomena of aluminium oxide in metal halide lamps

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, S; Markus, T [Institute for Energy Research, Forschungszentrum Juelich GmbH, D-52425 Juelich (Germany); Niemann, U [Philips GmbH, Research Laboratories, PO Box 500145, Aachen, D-52085 (Germany)], E-mail: s.fischer@fz-juelich.de

    2008-07-21

    A better understanding of the transport phenomena observed in metal halide lamps can be achieved using computer-based model calculations. The chemical transport of aluminium oxide in advanced high-pressure discharge vessels was calculated as a function of temperature and composition of the salt mixture relevant to the lamp. Below 1773 K chemical transport is the prevailing process; above this temperature the vaporization and condensation of the envelope material-aluminium oxide-become more important. The results of the calculations show that the amount of transported alumina increases linearly with the number of iteration cycles and exponentially with the temperature gradient.

  11. Determination of cadmium in aluminium by atomic absorption spectrometry

    International Nuclear Information System (INIS)

    Batistoni, D.A.; Erlijman, L.H.

    1978-12-01

    A direct method for the determination of cadmium in elemental aluminium is described. Metal samples are dissolved in diluted hydrochloric acid and cadmium is determined by atomic absorption spectrometry in an air-acetylene flame. Interference by non-specific absorption observed at the analytical wavelength incorrected for by means of a non-absorbing line emitted by the hollow-cathode lamp. Relatively large amounts of arsenic do not interfere. The minimun determinable concentration of cadmium for this procedure is 2-3 ppm, expressed on aluminium basis. (author) [es

  12. Towards an understanding of the adjuvant action of aluminium

    Science.gov (United States)

    Marrack, Philippa; McKee, Amy S.; Munks, Michael W.

    2011-01-01

    The efficacy of vaccines depends on the presence of an adjuvant in conjunction with the antigen. Of these adjuvants, the ones that contain aluminium, which were first discovered empirically in 1926, are currently the most widely used. However, a detailed understanding of their mechanism of action has only started to be revealed. In this Timeline article, we briefly describe the initial discovery of aluminium adjuvants and discuss historically important advances. We also summarize recent progress in the field and discuss their implications and the remaining questions on how these adjuvants work. PMID:19247370

  13. Effects of aluminium surface morphology and chemical modification on wettability

    DEFF Research Database (Denmark)

    Rahimi, Maral; Fojan, Peter; Gurevich, Leonid

    2014-01-01

    of a monolayer of fluorinated silane, and a combination of those. The effect of these surface modification techniques on roughness and wettability of the aluminium surfaces was elucidated by ellipsometry, contact angle measurements and atomic force microscopy. We demonstrated that by employing different types...... of surface modifications the contact angle of water droplets on aluminium samples can be varied from 12° to more than 120°. A crossover from Cassie–Baxter to Wenzel regime upon changing the surface roughness was also observed....

  14. Accumulation of Aluminium and Physiological Status of Tree Foliage in the Vicinity of a Large Aluminium Smelter

    Directory of Open Access Journals (Sweden)

    E. D. Wannaz

    2012-01-01

    Full Text Available A pollution gradient was observed in tree foliage sampled in the vicinity of a large aluminium production facility in Patagonia (Argentina. Leaves of Eucalyptus rostrata, and Populus hybridus and different needle ages of Pinus spec. were collected and concentrations of aluminium (Al and sulphur (S as well as physiological parameters (chlorophyll and lipid oxidation products were analyzed. Al and S concentrations indicate a steep pollution gradient in the study showing a relationship with the physiological parameters in particular membrane lipid oxidation products. The present study confirms that aluminium smelting results in high Al and sulphur deposition in the study area, and therefore further studies should be carried out taking into account potentially adverse effects of these compounds on human and ecosystem health.

  15. Determination of rare earth element content in yttrium aluminium garnet crystals by absorption spectrophotometry method

    International Nuclear Information System (INIS)

    Mejl'man, M.L.; Kolomijtsev, A.I.; Baskakova, Z.M.; Bagdasarov, Kh.S.; Kevorkov, A.M.

    1985-01-01

    Possibility of determination of relative and absolute contents of impurity trivalent REE ions in yttrium aluminium garnet of (YAG) monocrystals has been studied by the absorption spectrophotometry method. Absorption spectra in UV and visible regions YAG monocrystals doped by REE are studied. For each admixture the characteristic lines or absorption bands not overlapping with lines of other admixtures are defined and investigated. The extinction coefficients of characteristic lines are determined which allow one to measure absolute REE admixture concentrations in garnet crystals. A conclusion is drawn that the absorption spectrophotometry method permits to measure REE admixture content in YAG monocrystals within the concentration range of approximately 1x10sup(-3)-5 mas. % with an accuracy not less than 20% (with sample thickness of approximately 1 cm)

  16. A Numerical Analysis of the Resistance and Stiffness of the Aluminium and Concrete Composite Beam

    Directory of Open Access Journals (Sweden)

    Polus Łukasz

    2015-03-01

    Full Text Available In this paper a numerical analysis of the resistance and stiffness of the aluminium and concrete composite beam is presented. Composite aluminium and concrete structures are quite new and they have not been thoroughly tested. Composite structures have a lot of advantages. The composite aluminium and concrete beam is more corrosion-resistant, fire-resistant and stiff than the aluminium beam. The contemporary idea of sustainable buildings relies on new solutions which are more environmentally friendly. Aluminium is lighter and more resistant to corrosion than steel, which is often used in composite structures.

  17. Studi Perbandingan Keefektifan Penggunaan Poly Aluminium Chloride (PAC) dan Tawas (Alum) Terhadap Turbiditas dan Kadar Logam Aluminium Pada Air Baku Instalasi Pengolahan Air Di PDAM Tirtanadi Hamparan Perak

    OpenAIRE

    Gea, Deswanti Mariana

    2017-01-01

    The comparative effectiveness study of the usage of the poly aluminium chloride (PAC) and alum towards the turbidity and the aluminium levels at the water treatment installation of PDAM Hamparan Perak has been carried out. The concentration of aluminium chloride and alum usage compared in the raw water has initial turbidity 73,3 NTU and aluminium levels of 0,048 mg/l is respectively 19 ppm; 21 ppm and 23 ppm. And being stirred with agiator found in the Jar Test with a 140 rpm rotation spee...

  18. Experimental weathering rates of aluminium silicates

    International Nuclear Information System (INIS)

    Gudbrandsson, Snorri

    2013-01-01

    The chemical weathering of primary rocks and minerals in natural systems has a major impact on soil development and its composition. Chemical weathering is driven to a large extent by mineral dissolution. Through mineral dissolution, elements are released into groundwater and can readily react to precipitate secondary minerals such as clays, zeolites, and carbonates. Carbonates form from divalent cations (e.g. Ca, Fe and Mg) and CO 2 , and kaolin clay and gibbsite formation is attributed to the weathering of aluminium-rich minerals, most notably the feldspars. The CarbFix Project in Hellisheidi (SW-Iceland) aims to use natural weathering processes to form carbonate minerals by the re-injection of CO 2 from a geothermal power plant back into surrounding basaltic rocks. This process is driven by the dissolution of basaltic rocks, rich in divalent cations, which can combine with injected CO 2 to form and precipitate carbonates. This thesis focuses on the dissolution behaviour of Stapafell crystalline basalt, which consists of three major phases (plagioclase, pyroxene, and olivine) and is rich in divalent cations. Steady-state element release rates from crystalline basalt at far-from-equilibrium conditions were measured at pH from 2 to 11 and temperatures from 5 to 75 C in mixed-flow reactors. Steady-state Si and Ca release rates exhibit a U-shaped variation with pH, where rates decrease with increasing pH at acid condition but increase with increasing pH at alkaline conditions. Silicon release rates from crystalline basalt are comparable to Si release rates from basaltic glass of the same chemical composition at low pH and temperatures ≥25 C but slower at alkaline pH and temperatures ≥50 C. In contrast, Mg and Fe release rates decrease continuously with increasing pH at all temperatures. This behaviour is interpreted to stem from the contrasting dissolution behaviours of the three major minerals comprising the basalt: plagioclase, pyroxene, and olivine. Element

  19. Antioxidant Activity of Natural Products against Aluminium Fluoride ...

    African Journals Online (AJOL)

    Evaluation of antioxidant potential of natural products against Aluminium fluoride (AlF4) induced oxidative stress in albino mice were represented in the present study. Gossypin, Quercetin dehydrate, (-)-Epicatechin gallate, Gallic acid and Suramin sulphate (G-protein inhibitor) were evaluated for antioxidant activity by ...

  20. System for processing aluminium dross in a reduced oxygen environment

    Energy Technology Data Exchange (ETDEWEB)

    Rezac, K.-H.

    1987-01-01

    The processing of dross is becoming an increasingly important economic and environmental consideration in the production, recycling and foundry use of aluminium. It is important, therefore, to develop processes and equipment for cooling and processing dross in the most economical way possible combined with maximum environmental protection. This paper describes the equipment used for carrying out such processing and its operation.

  1. Aluminium dissolution for spray pulverization with nitric acid

    International Nuclear Information System (INIS)

    Rodrigo Otero, A.; Rodrigo Vilaseca, F.; Morales Calvo, G.

    1977-01-01

    A comparative study of the nitric acid dissolution of aluminium, by immersion and spray pulverization has been carried out in laboratory scale. As a result, the optimum operation conditions to control reaction in the plant are fixed. Operation costs are also evaluated. (author) [es

  2. Diamond turning and polishing tests on new RSP aluminium alloys

    NARCIS (Netherlands)

    Horst, R. ter; Haan, M. de; Gubbels, G.P.H.; Senden, R.; Venrooy, B.W.H. van; Hoogstrate, A.M.

    2012-01-01

    For years now conventional aluminium 6061 T6 has widely been used for mirrors in astronomical instruments, being diamond turned or since a few years also being optically polished. This allows the development of optical systems that can be tested and operated at any temperature, without being

  3. Microstructure and defect chemistry of yttrium aluminium garnet ceramics

    International Nuclear Information System (INIS)

    Schuh, L.H.

    1989-01-01

    This thesis describes basic aspects concerning the defect chemistry and the microstructure of yttrium aluminium garnet ceramics. The work consists of three parts: a literature study, an experimental part and a section giving computer simulation data of defects. (author). 320 refs.; 68 figs.; 72 schemes; 32 tabs

  4. Superhydrophobic coatings for aluminium surfaces synthesized by chemical etching process

    Directory of Open Access Journals (Sweden)

    Priya Varshney

    2016-10-01

    Full Text Available In this paper, the superhydrophobic coatings on aluminium surfaces were prepared by two-step (chemical etching followed by coating and one-step (chemical etching and coating in a single step processes using potassium hydroxide and lauric acid. Besides, surface immersion time in solutions was varied in both processes. Wettability and surface morphologies of treated aluminium surfaces were characterized using contact angle measurement technique and scanning electron microscopy, respectively. Microstructures are formed on the treated aluminium surfaces which lead to increase in contact angle of the surface (>150°. Also on increasing immersion time, contact angle further increases due to increase in size and depth of microstructures. Additionally, these superhydrophobic coatings show excellent self-cleaning and corrosion-resistant behavior. Water jet impact, floatation on water surface, and low temperature condensation tests assert the excellent water-repellent nature of coatings. Further, coatings are to be found mechanically, thermally, and ultraviolet stable. Along with, these coatings are found to be excellent regeneration ability as verified experimentally. Although aforesaid both processes generate durable and regenerable superhydrophobic aluminium surfaces with excellent self-cleaning, corrosion-resistant, and water-repellent characteristics, but one-step process is proved more efficient and less time consuming than two-step process and promises to produce superhydrophobic coatings for industrial applications.

  5. Optical and morphological investigation of aluminium and nickel ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 38; Issue 2. Optical and morphological investigation of aluminium and nickel oxide composite films deposited by spray pyrolysis method as a basis of solar thermal absorber. A Bagheri Khatibani S M Rozati. Volume 38 Issue 2 April 2015 pp 319-326 ...

  6. Depth profiling of aluminium metal using slow positron beam ...

    African Journals Online (AJOL)

    Slow positron beam Doppler-broadening technique was used to study depth profiling of aluminium metals sample. The variation of the line-shape parameters with incident positron energy was studied. Also, the depth profile of the S parameter was investigated. The positron implantation profile and backscattering fraction for ...

  7. Aluminium structures in building and civil engineering applications

    NARCIS (Netherlands)

    Soetens, F.

    2010-01-01

    Structural applications of aluminium are considered in this paper. Although the discussion is mainly devoted to Europe, the paper also refers, where possible, to developments in other parts of the world. The problems faced by a designer in creating an optimum design are described, followed by a

  8. Effect of strain path on severely deformed aluminium

    Czech Academy of Sciences Publication Activity Database

    Kunčická, L.; Kocich, R.; Král, Petr; Pohludka, M.; Marek, M.

    2016-01-01

    Roč. 180, OCT (2016), s. 280-283 ISSN 0167-577X Institutional support: RVO:68081723 Keywords : Twist channel angular pressing * Aluminium * Texture * Microstructure Electron microscopy * Metal forming and shaping Subject RIV: JG - Metallurgy Impact factor: 2.572, year: 2016

  9. Oxygen–induced barrier height changes in aluminium – amorphous ...

    African Journals Online (AJOL)

    The results show that the application of voltage causes charge exchange between the surface states and the semiconductor leading to a change in the height of the potential barrier for electrons passing from aluminium into the a-Se films. The empirically determined values of barrier height of Al/a-Se diodes with thin and ...

  10. Sensitivity analysis on ultimate strength of aluminium stiffened panels

    DEFF Research Database (Denmark)

    Rigo, P.; Sarghiuta, R.; Estefen, S.

    2003-01-01

    This paper presents the results of an extensive sensitivity analysis carried out by the Committee III.1 "Ultimate Strength" of ISSC?2003 in the framework of a benchmark on the ultimate strength of aluminium stiffened panels. Previously, different benchmarks were presented by ISSC committees on ul...

  11. Natural Aging Behaviour Of AA6111 Aluminium | Quainoo | Ghana ...

    African Journals Online (AJOL)

    In the continuing drive for weight reduction in new automobile designs, the 6000 series aluminium alloys have emerged as the most promising age-hardenable body sheet material in the automotive industry. Currently, one of the body sheet alloys used for its combination of strength and formability in the (T4) temper is ...

  12. Effects of Aluminium in Forest. Results of a pilot experiment

    Energy Technology Data Exchange (ETDEWEB)

    Mulder, J.; Wit, H. de; Nygaard, P.H.

    1996-01-01

    This conference paper deals with an Norwegian pilot project which started in 1995 and finishing early 1999, investigates the solubility and phyto-toxicity of aluminium (Al) in mature forest ecosystems. The project consists of three major parts, including field manipulation study of Norwegian spruce stands, laboratory experiments and modelling Al chemistry in the root zone. 15 refs.

  13. Differential effects of aluminium on the seedling parameters of wheat ...

    African Journals Online (AJOL)

    ... different aluminium (Al) concentrations on the seedling parameters of wheat and the effect of malate and citrate treatments as chelates for reducing the noxious effect of Al in medium culture and seedlings of two wheat cultivars, Darab (Al sensitive) and Maroon (Al tolerant) were grown on hydroponic solution (non modified ...

  14. Pressurized air ionization chamber with aluminium walls for radiometric dosimetry

    International Nuclear Information System (INIS)

    Rodrigues, R.G.S.; Pela, C.A.; Netto, T.G.

    1996-01-01

    A pressurized air ionization chamber with 23 cm 3 and aluminium walls is evaluated concerning its sensitiveness in low exposure rate. Considering conventional ionization chambers, this chamber shows a better performance since the air pressure of 2500 kPa minimizes the energy dependence to less than 5% between 40 and 1.250 keV

  15. Laser alloying of aluminium to improve surface properties - MSSA 2010

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2010-07-01

    Full Text Available Aluminium is vastly used in industry due to its low cost, light weight and excellent workability, but lacks in wear resistance and hardness. Laser alloying is used to improve the surface properties such as hardness by modifying the composition...

  16. Cavitation-aided grain refinement in aluminium alloys

    NARCIS (Netherlands)

    Atamanenko, T.V.

    2010-01-01

    This thesis deals with grain refinement under the influence of ultrasonic-driven cavitation in aluminium casting processes. Three major goals of this research were: (1) to identify the mechanism of the cavitation-aided grain refinement at different stages of solidification; (2) to reveal the

  17. Contribution to comprehensive study of aluminium alloy Aa 5083 ...

    African Journals Online (AJOL)

    Corrosion induced by elemental mercury in aqueous media of industrial Aluminium alloys AA5083 used in heat exchanger industries of natural gas liquefaction has been studied by linear sweep voltammétry on rotating amalgamated disk electrode. Corrosion process depends on: • Chemical processes of amalgamation of ...

  18. Local electrochemical behaviour of 7xxx aluminium alloys

    NARCIS (Netherlands)

    Andreatta, F.

    2004-01-01

    Aluminium alloys of the 7xxx series (Al-Zn-Mg-Cu) are susceptible to localized types of corrosion like pitting, intergranular corrosion and exfoliation corrosion. This represents a limitation for the application of these alloys in the aerospace components because localized corrosion might have a

  19. Hole quality and burr reduction in drilling aluminium sheets

    DEFF Research Database (Denmark)

    Pilny, Lukas; De Chiffre, Leonardo; Piska, Miroslav

    2011-01-01

    Optimization of the metal drilling process requires creation of minimum amount of burrs and uniform appearance of the drilled holes. In this paper, an experimental investigation was performed on 2 mm sheets of wrought aluminium alloy Al99.7Mg0.5Cu-H24, using 1.6 and 2 mm diameter drills. Cutting...

  20. Hole quality and burr reduction in drilling aluminium sheets

    DEFF Research Database (Denmark)

    Pilny, Lukas; De Chiffre, Leonardo; Piska, Miroslav

    2012-01-01

    Optimization of the metal drilling process requires creation of minimum amount of burrs and uniform appearance of the drilled holes. In this paper, an experimental investigation was performed on 2 mm sheets of wrought aluminium alloy Al99.7Mg0.5Cu-H24, using 1.6 and 2 mm diameter drills. Cutting...

  1. Differential effects of aluminium on the seedling parameters of wheat ...

    African Journals Online (AJOL)

    ALADDIN

    2011-04-25

    Apr 25, 2011 ... Key words: Triticum aestivum L., hydroponic, aluminium-tolerant, length of root, regression analysis. ... cat-ions those immediately surrounding the apical root ... A separate model statement is required for linear, quadratic and cubic trends. RESULTS. ANOVA revealed that, for seedling growth parameters.

  2. Combined aluminium sulfate/hydroxide process for fluoride removal ...

    African Journals Online (AJOL)

    Combined aluminium sulfate/hydroxide process for fluoride removal from drinking water. ... The reported removal efficiency of Nalgonda Technique is 70% at alum dose of 150-170 mg alum/mg F. Besides, sludge production is also minimized. Therefore, this process is highly efficient and could be applied in areas where the ...

  3. Aluminium hydride: a reversible material for hydrogen storage.

    Science.gov (United States)

    Zidan, Ragaiy; Garcia-Diaz, Brenda L; Fewox, Christopher S; Stowe, Ashley C; Gray, Joshua R; Harter, Andrew G

    2009-07-07

    Aluminium hydride has been synthesized electrochemically, providing a synthetic route which closes a reversible cycle for regeneration of the material and bypasses expensive thermodynamic costs which have precluded AlH(3) from being considered as a H(2) storage material.

  4. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  5. Novel package for inhibition of aluminium corrosion in alkaline solutions

    International Nuclear Information System (INIS)

    Abdel-Gaber, A.M.; Khamis, E.; Abo-Eldahab, H.; Adeel, Sh.

    2010-01-01

    Inhibition of aluminium corrosion in 2 M sodium hydroxide solution by a package composed of the cationic surfactant cetyl trimethyl ammonium bromide (CTAB) and lupine seed extract has been investigated employing different electrochemical techniques and chemical gasometry measurements. Potentiodynamic polarization curve measurements showed that lupine seed extract controls both the anodic dissolution of aluminium and the hydrogen gas evolved at the cathodic sites of aluminium surface. Nyquist plots showed two capacitive semicircles in the high and low frequency regions separated by an inductive loop at intermediate frequencies. The inductive loop may be explained by the occurrence of adsorbed intermediates on the surface. A proposed equivalent circuit was used to analyse the impedance spectra for aluminium in NaOH solutions. The corrosion inhibition data have been analysed using different isotherms. The results showed excellent agreement between the kinetic-thermodynamic model and Flory-Huggins isotherm. Gasometry measurements showed that the Inhibitive effect of the surfactant increases at a composition around its critical micelle concentration (cmc). The presence of both the surfactant and lupine seed extract did not indicate synergistic action between them. The mode of adsorption of the surfactant molecules corresponding to their structure is also discussed.

  6. Elaboration in the area of aluminium containing alloys

    International Nuclear Information System (INIS)

    Mirsaidov, U.M.

    2002-01-01

    In the Institute of Chemistry was elaborated the experimental-industrial installation and technology of deep aluminium purification by the methods of zone melting and recrystallization. The developed technology let receive the metal of model A5 N A6 N dependence from number of induction zone passage

  7. Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium ...

    Indian Academy of Sciences (India)

    Electrochemical; aluminium-doped zinc oxide; PVA-coated; UV sensing. 1. Introduction. Metal oxide semiconductors have received considerable attention due to their excellent physical and chemical prop- erties (Johnson et al 2001; Vayssieres et al 2001; Kolmakov and Moskovits 2004). Zinc oxide (ZnO), one of the most.

  8. Cold forming of aluminium - State of the art

    DEFF Research Database (Denmark)

    Bay, Niels

    1997-01-01

    The ongoing development of cold forging technology has been manifested lately by the increasing application of components in cold forged aluminium alloys. Applying precipitation hardening alloys components with great strength/weight ratio can be produced with a strength comparable to that of unal...

  9. Amelioration of behavioural toxicity of aluminium by oligomeric ...

    African Journals Online (AJOL)

    Despite its limited solubility at neutral pH, aluminium is significantly accumulated by the freshwater snail Lymnaea stagnalis, leading to behavioral toxicity. Both organic (humic acid) and non-organic (oligomeric silicic acid) ligands have been shown to reduce Al accumulation probably owing to their binding affinity for Al. This ...

  10. A vector valued Stefan problem from aluminium industry

    NARCIS (Netherlands)

    F.J. Vermolen; C. Vuik

    1998-01-01

    textabstractDissolution of stoichiometric multi-component particles in ternary alloys is an important process occurring during the heat treatment of as-cast aluminium alloys prior to hot-extrusion. A mathematical model is proposed to describe such a process. In this model an equation is given to

  11. Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium ...

    Indian Academy of Sciences (India)

    295–300. c Indian Academy of Sciences. Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium-doped zinc oxide nanorods. KANCHAN SAXENA. ∗. , AMIT KUMAR, NISHANT MALIK, PRAMOD KUMAR and V K JAIN. Amity Institute of Advanced Research and Studies (Materials and Devices), Amity University, ...

  12. Friction factor of CP aluminium and aluminium–zinc alloys

    Indian Academy of Sciences (India)

    zinc alloys using ring compression test at different temperatures from 303 K to 773 K. It is found that CP aluminium exhibits stick- ing whereas Al–Zn alloys do not exhibit sticking at elevated temperatures. Hot working of Al–Zn alloy is easier.

  13. STRUCTURE OF ECAP ALUMINIUM AFTER DIFFERENT NUMBER OF PASSES

    Directory of Open Access Journals (Sweden)

    Lucia Ilucová

    2011-05-01

    Full Text Available The structure of high purity (99.99% aluminium processed by equal channel angular pressing in the as pressed state after different number of passes was examined using various stereological methods. An extreme inhomogeneity and complicated anisotropy was observed along the body of rod-like specimens.

  14. Study of the dielectric parameters of aluminium ore bauxite of ...

    Indian Academy of Sciences (India)

    M. Senthilkumar (Newgen Imaging) 1461 1996 Oct 15 13:05:22

    are also calculated in the present studies. Keywords. Dielectric parameters; aluminium ore; packing density; minability of ore. 1. Introduction. Dielectric properties of solids in the form of powders may be useful in understanding the structural behaviour of particles in an alternating field. These studies may also be used to for-.

  15. Optical and morphological investigation of aluminium and nickel ...

    Indian Academy of Sciences (India)

    spectrophotometry, various physical properties were investigated. Different optical quantities such as optical band gap, refractive index, extinction coefficient, dielectric constants, volume and surface energy loss functions and optical conductivity were determined. Within this paper for different nickel to aluminium ratio (from ...

  16. Impact toughness of laser alloyed aluminium AA1200 alloys

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2013-08-01

    Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4kW Nd:YAG laser and impact resistance of the alloys was investigated. The alloying powders were a mixture of Ni, Ti and SiC in different proportions. Surfaces reinforced...

  17. Mechanochemical route to the synthesis of nanostructured Aluminium nitride

    Science.gov (United States)

    Rounaghi, S. A.; Eshghi, H.; Scudino, S.; Vyalikh, A.; Vanpoucke, D. E. P.; Gruner, W.; Oswald, S.; Kiani Rashid, A. R.; Samadi Khoshkhoo, M.; Scheler, U.; Eckert, J.

    2016-01-01

    Hexagonal Aluminium nitride (h-AlN) is an important wide-bandgap semiconductor material which is conventionally fabricated by high temperature carbothermal reduction of alumina under toxic ammonia atmosphere. Here we report a simple, low cost and potentially scalable mechanochemical procedure for the green synthesis of nanostructured h-AlN from a powder mixture of Aluminium and melamine precursors. A combination of experimental and theoretical techniques has been employed to provide comprehensive mechanistic insights on the reactivity of melamine, solid state metal-organic interactions and the structural transformation of Al to h-AlN under non-equilibrium ball milling conditions. The results reveal that melamine is adsorbed through the amine groups on the Aluminium surface due to the long-range van der Waals forces. The high energy provided by milling leads to the deammoniation of melamine at the initial stages followed by the polymerization and formation of a carbon nitride network, by the decomposition of the amine groups and, finally, by the subsequent diffusion of nitrogen into the Aluminium structure to form h-AlN. PMID:27650956

  18. Structure analysis of 3104 aluminium alloy applied to deep drawing

    Energy Technology Data Exchange (ETDEWEB)

    Klyszewski, A.; Lech-Grega, M.; Zelechowski, J.; Szymanski, W. [Light Metals Div., Skawina (Poland). Inst. of Non-Ferrous Metals

    2000-07-01

    Optical and electron microscopy observations and X-ray investigations of 3104 aluminium alloy ingots and bands after experimental heat treatment were carried out. The influence of ingots homogenisation temperature and parameters of material heat treatment after hot rolling on structure, texture and earing of band 0.3 mm thick was analysed. (orig.)

  19. Ultraviolet sensing properties of polyvinyl alcohol-coated aluminium ...

    Indian Academy of Sciences (India)

    Undoped and aluminium (Al)-doped zinc oxide (ZnO) nanorods have been synthesized by electrochemical route. The synthesized materials have been characterized by X-ray diffraction, UV–visible spectrometer and scanning electron microscope. The Al-doped ZnO nanorods have been coated with polyvinyl alcohol.

  20. Establishment of integrated information displays in aluminium surfaces using nanomanufacturing

    DEFF Research Database (Denmark)

    Prichystal, Jan; Hansen, Hans Nørgaard; Bladt, Henrik H.

    2006-01-01

    Bang & Olufsen has been working with a method for manufacturing ultra-thin structures in aluminium that can be penetrated by light. This work has resulted in a patent describing how to obtain this effect by material removal in local areas in a solid material. The idea behind an invisible display...

  1. Thin-film cryogenic resistors from aluminium alloys

    Science.gov (United States)

    Tadros, N. N.; Holdeman, L. B.

    The temperature dependence of the resistances of thin films sputtered from three commercially available aluminium alloys (5052, 5086, 5456) has been measured in the temperature range 1.5-4.2 K. The 5052-alloy films had a positive temperature coefficient of resistance (TCR) throughout this temperature range, whereas films of the other two alloys had a negative TCR.

  2. Verification of Some Vegetable Oils as Cutting Fluid for Aluminium

    African Journals Online (AJOL)

    Akorede

    ABSTRACT: Vegetable oils (palm oil, groundnut oil, shear butter oil and cotton seed oil) have been used as lubricants in the turning operation of aluminum under varying spindle speeds, feed rates and depths of cut and the results compared with kerosene (due to the gummy nature of aluminium metal). The parameters ...

  3. Aluminium localization and toxicity symptoms related to root growth ...

    Indian Academy of Sciences (India)

    We correlated root growth inhibition with aluminium (Al3+) localization and toxicity symptoms in rice roots using seedlings of two genotypes (tolerant and sensitive) that were exposed to different AlCl3 concentrations. Al3+ localization was evaluated by hematoxylin in primary roots and by morin in cross-sections of the root ...

  4. Aluminium(III) alkoxides as unique synthons for heterocyclic ...

    Indian Academy of Sciences (India)

    Administrator

    Facile reactivity of aluminium(III) alkoxides with organic protic reagents with alcohol as the only side product provides a convenient method for the synthesis of a variety of products which may not be synthesized by any other route. The possibility of removal of alcohol azeotropically with solvent benzene makes it possible to ...

  5. Pack nitriding of aluminium using cassava waste | Shitta | Journal of ...

    African Journals Online (AJOL)

    Pack Nitriding is a process analogous to pack carbonizing. In this work, cassava leaves were employed as a source of nitrogen. Upon heating, slow decomposition of the compound provides Nitrogen, the Nitrogen was allowed to interact with aluminium metal surfaces, which were packed nitrided at temperature of 350°c.

  6. Verification of Some Vegetable Oils as Cutting Fluid for Aluminium ...

    African Journals Online (AJOL)

    Vegetable oils (palm oil, groundnut oil, shear butter oil and cotton seed oil) have been used as lubricants in the turning operation of aluminum under varying spindle speeds, feed rates and depths of cut and the results compared with kerosene (due to the gummy nature of aluminium metal). The parameters investigated are ...

  7. A multiple buckling curve formulation for design of aluminium alloy ...

    African Journals Online (AJOL)

    The paper refers to the overall stability design of aluminium structural elements. Buckling curves for members subjected to compression and members subjected to bending are dealt with. The formulation is based on probabilistic considerations of two random events, namely the elastic buckling of a perfect member and the ...

  8. Electrochemical Characterisation of Filiform Corrosion on Aluminium Rolled Products

    NARCIS (Netherlands)

    Huisert, M.

    2001-01-01

    When aluminium is protected by an organic coating a special form of corrosion can occur underneath the organic coating; filiform corrosion. This form of corrosion manifests itself as threadlike filaments under the coating, it causes local delamination of the coating and the coating cannot protect

  9. Aluminium, een nieuw probleem voor landbouw en volksgezondheid? : een literatuuronderzoek

    NARCIS (Netherlands)

    Vos, G.

    1985-01-01

    Door middel van literatuuronderzoek zijn gegevens verzameld met betrekking tot het gedrag van aluminium in de bodem, de toxiciteit voor mens, plant en dier, het voorkomen in levensmiddelen en analysemethoden voor de bepaling van dit element. De huidige aluminiumbelasting via het

  10. Microwave assisted hydrolysis of aluminium metal and preparation ...

    Indian Academy of Sciences (India)

    Centre for Materials for Electronics Technology (C-MET), Department of Information Technology, Government of India, Athani PO, Thrissur 680 581, India. MS received 30 June 2009; revised 27 July 2009. Abstract. Phase pure boehmite particles were prepared by microwave assisted hydrolysis of aluminium sheets.

  11. Dissolved aluminium and the silicon cycle in the Arctic Ocean

    NARCIS (Netherlands)

    Middag, R.; de Baar, H. J. W.; Laan, P.; Bakker, K.

    2009-01-01

    Concentrations of dissolved (0.2 mu m filtered) aluminium (Al) have been determined for the first time in the Eurasian part of the Arctic Ocean over the entire water column during expedition ARK XXII/2 aboard R.V. Polarstern (2007). An unprecedented number of 666 samples was analysed for 44 stations

  12. Trap levels in Y-aluminium garnet scintillating crystals

    Czech Academy of Sciences Publication Activity Database

    Vedda, A.; Di Martino, D.; Martini, M.; Mareš, Jiří A.; Mihóková, Eva; Nikl, Martin; Solovieva, Natalia; Blažek, K.; Nejezchleb, K.

    2004-01-01

    Roč. 38, - (2004), s. 673-676 ISSN 1350-4487 Grant - others:NATO SfP (XX) 973510 Institutional research plan: CEZ:AV0Z1010914 Keywords : aluminium garnets * scintillators * cerium * thetmoluminescence Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.664, year: 2004

  13. Programming NET 35

    CERN Document Server

    Liberty, Jesse

    2009-01-01

    Bestselling author Jesse Liberty and industry expert Alex Horovitz uncover the common threads that unite the .NET 3.5 technologies, so you can benefit from the best practices and architectural patterns baked into the new Microsoft frameworks. The book offers a Grand Tour" of .NET 3.5 that describes how the principal technologies can be used together, with Ajax, to build modern n-tier and service-oriented applications. "

  14. Corrosion of research reactor aluminium clad spent fuel in water

    International Nuclear Information System (INIS)

    2009-12-01

    A large variety of research reactor spent fuel with different fuel meats, different geometries and different enrichments in 235 U are presently stored underwater in basins located around the world. More than 90% of these fuels are clad in aluminium or aluminium based alloys that are notoriously susceptible to corrosion in water of less than optimum quality. Some fuel is stored in the reactor pools themselves, some in auxiliary pools (or basins) close to the reactor and some stored at away-from-reactor pools. Since the early 1990s, when corrosion induced degradation of the fuel cladding was observed in many of the pools, corrosion of research reactor aluminium clad spent nuclear fuel stored in light water filled basins has become a major concern, and programmes were implemented at the sites to improve fuel storage conditions. The IAEA has since then established a number of programmatic activities to address corrosion of research reactor aluminium clad spent nuclear fuel in water. Of special relevance was the Coordinated Research Project (CRP) on Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase I) initiated in 1996, whose results were published in IAEA Technical Reports Series No. 418. At the end of this CRP it was considered necessary that a continuation of the CRP should concentrate on fuel storage basins that had demonstrated significant corrosion problems and would therefore provide additional insight into the fundamentals of localized corrosion of aluminium. As a consequence, the IAEA started a new CRP entitled Corrosion of Research Reactor Aluminium Clad Spent Fuel in Water (Phase II), to carry out more comprehensive research in some specific areas of corrosion of aluminium clad spent nuclear fuel in water. In addition to this CRP, one of the activities under IAEA's Technical Cooperation Regional Project for Latin America Management of Spent Fuel from Research Reactors (2001-2006) was corrosion monitoring and surveillance of research

  15. The Hamlet dilemma for aluminium cans in the circular economy: to be or not to be in a closed loop?

    OpenAIRE

    Niero, Monia; Hoffmeyer, Simon B.; Langen, Håkon; Olsen, Stig Irving

    2015-01-01

    In the context of circular economy the focus is not only on recycling from a quantitative point of view, but also on improving the quality of materials. We considered the case of aluminium cans, and quantified the influence of alloying elements on the overall environmental performances of aluminium can recycling. We performed a Life Cycle Assessment (LCA) comparing different sources of aluminium: primary aluminium and mixed scraps, Used Beverage Can (UBC) scrap, mixed aluminium packaging scra...

  16. Adsorption of lithium ion to amorphous hydrous aluminium oxide

    International Nuclear Information System (INIS)

    Wada, Hideo; Kitamura, Takao; Fujii, Ayako; Katoh, Shunsaku

    1982-01-01

    Adsorption process of lithium ion to amorphous hydrous aluminium oxide (a-HAO) was investigated by pH titration method with lithium chloride-lithium hydroxide mixed solution and X-ray diffraction analysis of a-HAO after pH titration. In the pH titration, the addition of hydroxide ion in amount from 0 to 4.0 mmol.g -1 gave no change to the pH of the solution and caused adsorption of lithium ion equivalent in amount to added hydroxide ion. X-ray diffraction analysis showed the formation of lithium hydrogenaluminate LiH (AlO 2 ) 2 .5H 2 O (LHA) in the a-HAO after pH titration. These results showed that adsorption of lithium ion by a-HAO was related to a reaction which consumed hydroxide ion and formed LHA. In order to elucidate detail process of the reaction, changes of pH, aluminium concentration and lithium concentration of the solution, respectively with time, were determined. The pH of the solution decreased in two stages. At the first stage of the pH decrease, the aluminium concentration increased whereas the lithium concentration did not change. At the second stage, the lithium concentration decreased together with the decrease of the aluminium concentration. It was inferred that adsorption of lithium ion proceeded through dissolution of a-HAO and precipitation of LHA. Theoretical adsorption capacity calculated from the above formula for LHA and aluminium content in a-HAO was 4.7 mmol.g -1 and agreed fairly well with observed value 4.0 mmol.g -1 . (author)

  17. Sea corrosion protection: comparison between aluminium covering deposited by thermal spray with compressed air, argon and nitrogen; Protecao contra a corrosao marinha: comparacao de revestimentos de aluminio depositados por aspersao termica com ar comprimido, argonio e nitrogenio

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, Regina M.H. Pombo; Cortes Paredes, Ramon S. [Parana Univ., Curitiba, PR (Brazil). Centro Politecnico]. E-mail: regina@demec.ufpr.br; ramon@demec.ufpr.br; ramon@lactec.org.br; Silva, Jose Maurilio da [Instituto de Tecnologia para o Desenvolvimento (LACTEC), Curitiba, PR (Brazil)]. E-mail: maur�lio@lactec.org.br

    2003-07-01

    In this work, aluminium coverings deposited by thermal spray through different projecting gases were studied. Our aim was to evaluate the passive effect of the aluminium oxide in presence of different gases in order to choose the best condition against sea corrosion of ships, offshore and industrial installations. The aluminium coverings were deposited through electric arc thermal spray process, with pre-heating of the substratum and use of argon, nitrogen or air compressed. The evolution against sea corrosion was made through electrochemical tests, where anodic potentiodynamic curves were plotted. A 3,5% NaCl aqueous solution simulated the marine medium. The must protective covering was the one deposited with compressed air followed by the nitrogen and argon gases. All studied coatings showed corrosion potential that allows the steel cathodic protection. It was concluded that because the covering using compressed air, which is also the cheapest process, generates more oxide, the protection was enhanced compared to argon or nitrogen. (author)

  18. 18 CFR 35.35 - Transmission infrastructure investment.

    Science.gov (United States)

    2010-04-01

    ... 18 Conservation of Power and Water Resources 1 2010-04-01 2010-04-01 false Transmission infrastructure investment. 35.35 Section 35.35 Conservation of Power and Water Resources FEDERAL ENERGY... AND TARIFFS Transmission Infrastructure Investment Provisions § 35.35 Transmission infrastructure...

  19. Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

    Energy Technology Data Exchange (ETDEWEB)

    Vera, Rosa, E-mail: rvera@ucv.c [Instituto de Quimica, Facultad de Ciencias, Pontificia Universidad Catolica de Valparaiso, Avda. Brasil 2950, Casilla 4059, Valparaiso (Chile); Verdugo, Patricia [Departamento de Quimica y Bioquimica, Facultad de Ciencias, Universidad de Valparaiso, Av. Gran Bretana 1111, Valparaiso (Chile); Orellana, Marco; Munoz, Eduardo [Instituto de Quimica, Facultad de Ciencias, Pontificia Universidad Catolica de Valparaiso, Avda. Brasil 2950, Casilla 4059, Valparaiso (Chile)

    2010-11-15

    Research highlights: {yields} The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. {yields} In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. {yields} The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

  20. Decreased toxicity of aluminium when the ionic strength increases in water; Blir aluminium mindre toksisk naar ionestyrken i vannet oeker?

    Energy Technology Data Exchange (ETDEWEB)

    Alstad, E.W. [Oslo Univ. (Norway)

    1996-01-01

    The conference paper evaluates the acute mortality of fish caused by the toxicity of aluminium in water. The evaluation is based on the polymerization hypothesis. According to the author, the level of toxicity decreases when the concentration and charge of ions increase. The paper presents the preliminary results from the executed experiment. 2 refs., 2 figs., 1 tab.

  1. Corrosion of aluminium in copper-aluminium couples under a marine environment: Influence of polyaniline deposited onto copper

    International Nuclear Information System (INIS)

    Vera, Rosa; Verdugo, Patricia; Orellana, Marco; Munoz, Eduardo

    2010-01-01

    Research highlights: → The presence of Polyaniline in the Al-Cu system produces a decrease in the oxygen reduction reaction. → In the marine enviroment, aluminium in Al-Cu couples, suffers pitting and exfoliation. → The aluminium deterioration increases with chloride and enviromental sulphur dioxide presence, mainly when it is united to bare copper. - Abstract: In this study, we examined how aluminium corrosion in Al-Cu/PANI galvanic couples in a marine environment is influenced by deposition of polyaniline (PANI) on copper. Polarization curves and immersion assays in 0.1 M NaCl were performed. The morphologies of etched Al and corrosion products were observed by SEM, and the Al ions in solution were quantified by atomic absorption spectroscopy. A reduction in aluminium damage due to galvanic corrosion was observed as a result of decreased effective area for the oxygen reduction reaction on Cu/PANI electrode. Furthermore, an electrochemical reduction of PANI from leucoemeraldine to emeraldine base is proposed.

  2. Energy conversion from aluminium and phosphate rich solution via ZnO activation of aluminium

    Energy Technology Data Exchange (ETDEWEB)

    Slaughter, Gymama, E-mail: gslaught@umbc.edu; Sunday, Joshua; Stevens, Brian

    2015-08-01

    Electrochemical power sources have motivated intense research efforts in the development of alternative ‘green’ power sources for ultra-low powered bioelectronic devices. Biofuel cells employ immobilized enzymes to convert the available chemical energy of organic fuels directly into electricity. However, biofuel cells are limited by short lifetime due to enzyme inactivation and frequent need to incorporate mediators to shuttle electrons to the final electron acceptor. In this context, other electrochemical power sources are necessary in energy conversion and storage device applications. Here we report on the fabrication and characterization of a membrane-free aluminium/phosphate cell based on the activation of aluminium (Al) using ZnO nanocrystal in an Al/phosphate cell as a ‘green’ alternative to the traditional enzymatic biofuel cells. The hybrid cell operates in neutral phosphate buffer solution and physiological saline buffer. The ZnO modifier in the phosphate rich electrolyte activated the pitting of Al resulting in the production of hydrogen, as the reducing agent for the reduction of H{sub 2}PO{sub 4}{sup −} ions to HPO{sub 3}{sup 2−} ions at a formal potential of −0.250 V vs. Ag/AgCl. Specifically, the fabricated cell operating in phosphate buffer and physiological saline buffer exhibit an open-circuit voltage of 0.810 V and 0.751 V and delivered a maximum power density of 0.225 mW cm{sup −2} and 1.77 mW cm{sup −2}, respectively. Our results demonstrate the feasibility of generating electricity by activating Al as anodic material in a hybrid cell supplied with phosphate rich electrolyte. Our approach simplifies the construction and operation of the electrochemical power source as a novel “green” alternative to the current anodic substrates used in enzymatic biofuel cells for low power bioelectronics applications. - Graphical abstract: Display Omitted - Highlights: • ZnO activation of metallic Al for generating electricity for

  3. Aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference.

    Science.gov (United States)

    Zhao, Xue Qiang; Guo, Shi Wei; Shinmachi, Fumie; Sunairi, Michio; Noguchi, Akira; Hasegawa, Isao; Shen, Ren Fang

    2013-01-01

    Acidic soils are dominated chemically by more ammonium and more available, so more potentially toxic, aluminium compared with neutral to calcareous soils, which are characterized by more nitrate and less available, so less toxic, aluminium. However, it is not known whether aluminium tolerance and nitrogen source preference are linked in plants. This question was investigated by comparing the responses of 30 rice (Oryza sativa) varieties (15 subsp. japonica cultivars and 15 subsp. indica cultivars) to aluminium, various ammonium/nitrate ratios and their combinations under acidic solution conditions. indica rice plants were generally found to be aluminium-sensitive and nitrate-preferring, while japonica cultivars were aluminium-tolerant and relatively ammonium-preferring. Aluminium tolerance of different rice varieties was significantly negatively correlated with their nitrate preference. Furthermore, aluminium enhanced ammonium-fed rice growth but inhibited nitrate-fed rice growth. The results suggest that aluminium tolerance in rice is antagonistic with nitrate preference and synergistic with ammonium preference under acidic solution conditions. A schematic diagram summarizing the interactions of aluminium and nitrogen in soil-plant ecosystems is presented and provides a new basis for the integrated management of acidic soils.

  4. Aluminium content of foods originating from aluminium-containing food additives.

    Science.gov (United States)

    Ogimoto, Mami; Suzuki, Kumi; Haneishi, Nahoko; Kikuchi, Yuu; Takanashi, Mayu; Tomioka, Naoko; Uematsu, Yoko; Monma, Kimio

    2016-09-01

    Aluminium (Al) levels of 90 food samples were investigated. Nineteen samples contained Al levels exceeding the tolerable weekly intake (TWI) for young children [body weight (bw): 16 kg] when consuming two servings/week. These samples were purchased multiple times at specific intervals and were evaluated for Al levels. Al was detected in 27 of the 90 samples at levels ranging from 0.01 (limit of quantitation) to 1.06 mg/g. Of these, the Al intake levels in two samples (cookie and scone mix, 1.3 and 2 mg/kg bw/week, respectively) exceeded the TWI as established by European Food Safety Authority, although the level in the scone mix was equivalent to the provisional TWI (PTWI) as established by Joint Food and Agriculture Organization of the United Nations/World Health Organization Expert Committee on Food Additives. The Al levels markedly decreased in 14 of the 19 samples with initially high Al levels. These results indicated reductions in the Al levels to below the PTWI limits in all but two previously identified food samples.

  5. Method of preparing an Al-Ti-B grain refiner for aluminium-comprising products, and a method of casting aluminium products

    NARCIS (Netherlands)

    Brinkman, H.J.; Duszczyk, J.; Katgerman, L.

    1999-01-01

    The invention relates to a method of preparing an Al-Ti-B grain refiner for cast aluminium-comprising products. According to the invention the preparation is realized by mixing powders selected from the group comprising aluminium, titanium, boron, and alloys and intermetallic compounds thereof,

  6. 48 CFR 6302.35 - Dismissal without prejudice (Rule 35).

    Science.gov (United States)

    2010-10-01

    ... prejudice (Rule 35). 6302.35 Section 6302.35 Federal Acquisition Regulations System DEPARTMENT OF TRANSPORTATION BOARD OF CONTRACT APPEALS RULES OF PROCEDURE 6302.35 Dismissal without prejudice (Rule 35). When... prejudice to its restoration to the Board's docket when the cause of suspension has been eliminated. Unless...

  7. Thermal Effect of Ceramic Nanofiller Aluminium Nitride on Polyethylene Properties

    Directory of Open Access Journals (Sweden)

    Omer Bin Sohail

    2012-01-01

    Full Text Available Ethylene polymerization was done to form polyethylene nano-composite with nanoaluminum nitride using zirconocene catalysts. Results show that the catalytic activity is maximum at a filler loading of 15 mg nanoaluminum nitride. Differential scanning calorimeter (DSC and X-ray diffraction (XRD results show that percentage crystallinity was also marginally higher at this amount of filler. Thermal behavior of polyethylene nanocomposites (0, 15, 30, and 45 mg was studied by DSC and thermal gravimetric analyzer (TGA. Morphology of the component with 15 mg aluminium nitride is more fibrous as compared to 0 mg aluminium nitride and higher filler loading as shown by SEM images. In order to understand combustibility behavior, tests were performed on microcalorimeter. Its results showed decrease in combustibility in polyethylene nanocomposites as the filler loading increases.

  8. Environment pollution with aluminium around a coalburning electric power plant

    International Nuclear Information System (INIS)

    Hermann, J.

    1997-01-01

    The experiments were carried out from November 1991 till November 1993 on the area surrounding an electric power plant within the circle of 20 km diameter and five geographical directions (N, S, SE, E, W). The results presented in this paper have indicated the threats caused by emissions of the power plant ashes and dusts. Mean aluminium content in soil has been multiply surpassed on the area studied. This must have as impact on fauna and flora. The distribution and intensity of pollution is determined first of all by the distance from the emitters and direction of prevailing winds. A part of aluminium contained in water soluble compounds can be distributed on large areas, what adds a lot to the threat to animals. That is why high chimneys do not solve the problem of pollution around big industrial plants. (author)

  9. High-pressure direct synthesis of aluminium nitride

    CERN Document Server

    Bockowski, M; Grzegory, I; Krukowski, S; Wróblewski, M; Porowski, S

    2002-01-01

    We report the results of direct synthesis of aluminium nitride (AlN) under high nitrogen pressure up to 1 GPa and temperatures up to 2000 K. At pressure from 10 to 650 MPa we observe the combustion synthesis of AlN. As the result of the combustion process one can obtain the AlN sintered powder or AlN/Al metal matrix composites. For N sub 2 pressure higher than 650 MPa the crystal growth of AlN from the solution of atomic nitrogen in aluminium is possible. Both needle-like and bulk AlN single crystals, up to 1 cm and 1 mm, respectively, have been obtained.

  10. TORSIONAL DEFORMATION AND FATIGUE BEHAVIOUR OF 6061 ALUMINIUM ALLOY

    Directory of Open Access Journals (Sweden)

    marini marno

    2012-02-01

    Full Text Available Torsional deformation and fatigue behaviour of both solid and thin-walled tubular specimens were made from as-received and heat treated 6061 aluminium alloy were studied. 6061 aluminium alloy have been widely used as a candidate material in automobile, aerospace, aircraft and structural application because of their superior mechanical properties such as high strength to weight ratio, good ductility and others. The differences in cyclic deformation and fatigue behaviours between round and solid specimens where a stress gradient exist, and thin-walled tubular specimens where a uniform stress state is commonly assumed, are also discussed. Von Mises and Tresca criteria has been used to predict the monotonic and cyclic deformation curve and compared to the torsional data obtained from the experiment. The S-N curve was used to present and evaluate the fatigue life of the specimens. Through fractographic analysis, failure criteria of fracture surfaces were observed and discussed. 

  11. Numerical Modelling of Drawbeads for Forming of Aluminium Alloys

    Science.gov (United States)

    Joshi, Y.; Christiansen, P.; Masters, I.; Bay, N.; Dashwood, R.

    2016-08-01

    The drawbeads in stamping tools are usually designed based on experience from the forming of steel. However, aluminium alloys display different forming behaviour to steels, which is not reflected in the drawbead design for tools used for stamping aluminium. This paper presents experimental results from different semi-circular drawbead geometries commonly encountered in automotive dies and compares them to those obtained from Stoughton's analytical drawbead model and the 2D plane strain drawbead model set up using LS-DYNA. The study was conducted on lubricated NG5754 strips. The results presented are in terms of drawbead restraining force versus strip displacement, as a function of drawbead depth. The FE drawbead model agrees well with the experiments whereas the analytical model overpredicted the drawbead forces.

  12. Dynamical properties of aluminium from experimental dispersion relations

    International Nuclear Information System (INIS)

    Salles Filho, J.B.V.; Fulfaro, R.; Vinhas, L.A.

    1987-05-01

    Measurements of phonon dispersion relations of aluminium along the high symmetry directions were performed by coherent inelastic scattering of thermal neutrons technique. All measurements were taken at room temperature using the IPEN triple axis neutorn spectrometer. The results obtained with accuracy are in good agreement with the published data. The dispersion relations were calculated theoretically within the framework of Born-von Karman and Axially Symmetric models, including interactions up to the fifth nearest shell of atoms. The elastic constants were determined using the values of sound propagating velocity obtained directly from the dispersion relations along of high symmetry directions of the crystal. Applying theoretical models the force constants of aluminium were also determined. From these data several physical properties of the metal can be obtained. (Author) [pt

  13. Neutron small angle scattering of irradiated aluminium-silicon alloys

    International Nuclear Information System (INIS)

    Kostorz, G.

    1976-01-01

    Technically pure aluminium and aluminium-silicon alloys (0.43, 0.83 and 1.2% Si, also containing 0.11 to 0.14 at. % Fe) were investigated by slow neutron small angle scattering after irradiation with fast neutrons at low temperatures. Different irradiation levels, ageing at room temperature and at 60/70 0 C had no measurable effect upon small angle scattering cross-sections. From the experimental precision upper limit for the amount of Si involved in clustering after irradiation can be given. The observed small angle scattering shows a strong dependence on scattering angles and is attributed to large precipitates of Al 12 Fe 3 Si. A surface layer on the as-received samples is identified as another source of low-intensity small angle scattering. (orig.) [de

  14. Longitudinal study of workers of an aluminium die casting factory.

    Science.gov (United States)

    Discalzi, G L; Capellaro, F; Baracco, A

    1992-01-01

    We conducted a 5-year longitudinal study on 76 workers of a high and medium aluminium alloy die-casting factory. As in a previous cross-sectional study conducted in 1986 and in accordance with the data in the literature, the 1990 follow-up study showed: a low prevalence of chronic bronchitis (as defined by the ECSC questionnaire on respiratory symptoms); normal mean functional values of FVC, FEV1, FEV1/FVC%. We did not find any significant difference in the levels of lung function over the period of 1986-90. These results show that workers in the secondary aluminium industry are not exposed to a significant risk of chronic pulmonary disease.

  15. Nanosized f.c.c. thallium inclusions in aluminium

    International Nuclear Information System (INIS)

    Johnson, E.; Johansen, A.; Thoft, N.B.; Andersen, H.H.; Sarholt-Kristensen, L.

    1993-01-01

    Ion implantation of pure aluminium with thallium induces the formation of nanosized crystalline inclusions of thallium with a f.c.c. structure. The size of the inclusions depends on the implantation conditions and subsequent annealing treatments and is typically in the range from 1 to 10 nm. The inclusions are aligned topotactically with the aluminium matrix with a cube-cube orientation relationship and they have a truncated octahedral shape bounded by {111} and {001} planes. The lattice parameter of the f.c.c. thallium inclusions is 0.484 ± 0.002 nm, which is slightly but significantly larger than in the high-pressure f.c.c. thallium phase known to be stable above 3.8 GPa. (Author)

  16. Influence of Chemical Composition on Porosity in Aluminium Alloys

    Directory of Open Access Journals (Sweden)

    Kucharčík L.

    2014-06-01

    Full Text Available Porosity is one of the major defects in aluminum castings, which results is a decrease of a mechanical properties. Porosity in aluminum alloys is caused by solidification shrinkage and gas segregation. The final amount of porosity in aluminium castings is mostly influenced by several factors, as amount of hydrogen in molten aluminium alloy, cooling rate, melt temperature, mold material, or solidification interval. This article deals with effect of chemical composition on porosity in Al-Si aluminum alloys. For experiment was used Pure aluminum and four alloys: AlSi6Cu4, AlSi7Mg0, 3, AlSi9Cu1, AlSi10MgCu1.

  17. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines.

    Science.gov (United States)

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E; Bygum, Anette

    2016-11-02

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year period 2003 to 2013 we identified 47 children with persistent skin reactions caused by childhood vaccinations. Most patients had a typical presentation of persisting pruritic subcutaneous nodules. Five children had a complex diagnostic process involving paediatricians, orthopaedics and plastic surgeons. Two patients had skin biopsies performed from their skin lesions, and 2 patients had the nodules surgically removed. Forty-two children had a patch-test performed with 2% aluminium chloride hexahydrate in petrolatum and 39 of them (92%) had a positive reaction. The persistent skin reactions were treated with potent topical corticosteroids and disappeared slowly. Although we advised families to continue vaccination of their children, one-third of parents omitted or postponed further vaccinations.

  18. Melting and solidification of bismuth inclusions in aluminium

    DEFF Research Database (Denmark)

    Thoft, N.B.; Bohr, J.; Buras, B.

    1995-01-01

    Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different experime......Supercooling of crystalline bismuth inclusions in aluminium crystals has been observed and studied with different techniques: x-ray diffraction, in situ Rutherford backscattering/channelling spectrometry and transmission electron microscopy. The results of the measurements with different...... experimental methods (and on different samples) agree remarkably well. The inclusions melt at temperatures at or below the bismuth bulk melting point, and the solid/liquid phase transition exhibits a hysteresis of 100-150 K. Average inclusion sizes ranged from a few nm to some tens of nm. The x-ray diffraction...

  19. Experimental wear behaviour of cryogenically treated aluminium 6063 and 8011 materials

    Directory of Open Access Journals (Sweden)

    K. K. Padmanabhan

    2016-12-01

    Full Text Available The aim of this paper is to focus on the effect of cryogenic treatment on the microstructure, mechanical and wear properties of Al 6061 and Al 8011. The first objective was to understand the degree to which wear behaviour has shown improvement with aluminium grades being treated cryogenically on the specimens. To conduct wear test Aluminium experimental investigation has been carried out on aluminium alloys with cryogenic coolants. The cryogenic coolant has increased the wear resistance properties of aluminium upto 25% when compared to wear of non-cryogenically treated aluminium. The cryogenic treatment was carried out under three different timings for three different rpm’s under varying loads. The paper also studies the micro structural changes under these varying conditions. The experimental investigation of the paper concludes that cryogenically treated aluminium shows increase in wear resistance of nearly 25%.

  20. Simulation of Acoustic Wave Propagation in Aluminium Coatings for Material Characterization

    Directory of Open Access Journals (Sweden)

    Eva Grünwald

    2017-12-01

    Full Text Available Aluminium coatings and their characterization are of great interest in many fields of application, ranging from aircraft industries to microelectronics. Here, we present the simulation of acoustic wave propagation in aluminium coatings via the elastodynamic finite integration technique (EFIT in comparison to experimental results. The simulations of intensity (I–defocus (z curves, obtained by scanning acoustic microscopy (SAM, were first carried out on an aluminium bulk sample, and secondly on a 1 µm aluminium coating deposited on a silicon substrate. The I(z curves were used to determine the Rayleigh wave velocity of the aluminium bulk sample and the aluminium coating. The results of the simulations with respect to the Rayleigh velocity were corroborated by non-destructive SAM measurements and laser ultrasonic measurements (LUS.

  1. Aluminium in food and daily dietary intake assessment from 15 food groups in Zhejiang Province, China.

    Science.gov (United States)

    Zhang, Hexiang; Tang, Jun; Huang, Lichun; Shen, Xianghong; Zhang, Ronghua; Chen, Jiang

    2016-06-01

    Aluminium was measured in 2580 samples of 15 food groups and dietary exposure was estimated. Samples were purchased and analysed during 2010 to 2014. High aluminium levels were found in jellyfish (mean 4862 mg/kg), laver (mean 455.2 mg/kg) and fried twisted cruller (mean 392.4 mg/kg). Dietary exposure to aluminium was estimated for Zhejiang residents. The average dietary exposure to aluminium via 15 food groups in Zhejiang Province was 1.15 mg/kg bw/week, which is below the provisional tolerable weekly intake of 2 mg/kg bw /week. Jellyfish is the main Al contributor, providing 37.6% of the daily intake via these 15 food groups. This study provided new information on aluminium levels and assessment of aluminium (Al) dietary exposure in Zhejiang Province of China.

  2. RESPONSE OF PHENOLIC METABOLISM INDUCED BY ALUMINIUM TOXICITY IN FAGOPYRUM ESCULENTUM MOENCH. PLANTS.

    Science.gov (United States)

    Smirnov, O E; Kosyan, A M; Kosyk, O I; Taran, N Yu

    2015-01-01

    Buckwheat genus (Fagopyrum Mill.) is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 μM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench). Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL) were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2%) and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

  3. Response of phenolic metabolism induced by aluminium toxicity in Fagopyrum esculentum Moench. plants

    Directory of Open Access Journals (Sweden)

    O. E. Smirnov

    2015-12-01

    Full Text Available Buckwheat genus (Fagopyrum Mill. is one of the aluminium tolerant taxonomic units of plants. The aim of the study was an evaluation of the aluminium (50 µM effect on phenolic accumulation in various parts of buckwheat plants (Fagopyrum esculentum Moench.. Detection of increasing of total phenolic content, changes in flavonoid and anthocyanin content and phenylalanine ammonia-lyase activity (PAL were revealed over a period of 10 days of exposure to aluminium. The most significant effects of aluminium treatment on phenolic compounds accumulation were total phenolic content increasing (by 27.2% and PAL activity rising by 2.5 times observed in leaves tissues. Received data could be helpful to understand the aluminium tolerance principles and relationships of phenolic compounds to aluminium phytotoxicity.

  4. Non-LTE aluminium abundances in late-type stars

    Science.gov (United States)

    Nordlander, T.; Lind, K.

    2017-11-01

    Aims: Aluminium plays a key role in studies of the chemical enrichment of the Galaxy and of globular clusters. However, strong deviations from LTE (non-LTE) are known to significantly affect the inferred abundances in giant and metal-poor stars. Methods: We present non-local thermodynamic equilibrium (NLTE) modeling of aluminium using recent and accurate atomic data, in particular utilizing new transition rates for collisions with hydrogen atoms, without the need for any astrophysically calibrated parameters. For the first time, we perform 3D NLTE modeling of aluminium lines in the solar spectrum. We also compute and make available extensive grids of abundance corrections for lines in the optical and near-infrared using one-dimensional model atmospheres, and apply grids of precomputed departure coefficients to direct line synthesis for a set of benchmark stars with accurately known stellar parameters. Results: Our 3D NLTE modeling of the solar spectrum reproduces observed center-to-limb variations in the solar spectrum of the 7835 Å line as well as the mid-infrared photospheric emission line at 12.33 μm. We infer a 3D NLTE solar photospheric abundance of A(Al) = 6.43 ± 0.03, in exact agreement with the meteoritic abundance. We find that abundance corrections vary rapidly with stellar parameters; for the 3961 Å resonance line, corrections are positive and may be as large as +1 dex, while corrections for subordinate lines generally have positive sign for warm stars but negative for cool stars. Our modeling reproduces the observed line profiles of benchmark K-giants, and we find abundance corrections as large as -0.3 dex for Arcturus. Our analyses of four metal-poor benchmark stars yield consistent abundances between the 3961 Å resonance line and lines in the UV, optical and near-infrared regions. Finally, we discuss implications for the galactic chemical evolution of aluminium.

  5. Methods for production of aluminium powders and their application fields

    Energy Technology Data Exchange (ETDEWEB)

    Gopienko, V.G.; Kiselev, V.P.; Zobnina, N.S. (Vsesoyuznyj Nauchno-Issledovatel' skij i Proektnyj Inst. Alyuminievoj, magnievoj i ehlektrodnoj promyshlennosti (USSR))

    1984-12-01

    Different types of powder products made of alluminium and its alloys (powder, fine powders, granules and pastes) as well as their basic physicochemical properties are briefly characterized. The principle methods for alluminium powder production are outlined: physicochemical methods, the melt spraying by compressed gas being the mostly developed among them, and physico-mechanical ones. Main application spheres for powder productions of aluminium and its alloys are reported in short.

  6. Natural Aging Behaviour Of AA6111 Aluminium | Quainoo | Ghana ...

    African Journals Online (AJOL)

    Natural aging is observed to affect the kinetic reaction of AA6111. Dans la campagne continue pour la réduction en poids dans le nouveau modèle d\\' automobile, les séries 6000 d\\' aluminium en alliage ont émergé comme le matériau de feuille de carrosserie la plus prometteuse endurcirable avec l\\'âge dans l\\'industrie de ...

  7. Friction factor of CP aluminium and aluminium–zinc alloys

    Indian Academy of Sciences (India)

    The Rock- well hardness of all the samples were also measured. 3. Results and discussion. Friction factor, m, of CP aluminium is given in table 1 for various test temperatures. The friction factor, m, was low. (0⋅09–0⋅34) up to 673 K but it reached 0⋅90 at 773 K ex- hibiting sticking behaviour. Figure 5 shows the plot of.

  8. Cyclic behaviour and fatigue life prediction in welded aluminium joints

    International Nuclear Information System (INIS)

    Kosteas, D.

    1979-01-01

    The paper gives an overall state-of-the-art view of international attempts to find a solution, describes cyclic stress-strain behavior for the different zones of aluminium weldments, as stated above, states results from a recent research program of the Versuchsanstalt Stahl, Holz, und Steine in Karlsruhe and gives a step by step model for the calculation procedure of fatigue life. (orig.) 891 RW/orig. 892 RKD [de

  9. Configuration and mobility of hydrogen implanted in aluminium

    International Nuclear Information System (INIS)

    Bugeat, J.P.; Chami, A.C.; Ligeon, E.

    1976-01-01

    Localization methods through channeling and nuclear reaction analysis using low energy ion beam were applied to the study of deuterium and hydrogen implanted in aluminium single crystals. It was shown that implanted hydrogen occupies a tetrahedral site in the lattice as far as the implantation temperature is lower than 175K. This fact is interpreted by considering an interaction between hydrogen and monovacancies created during the implantation [fr

  10. Numerical modeling of aluminium foam on two scales

    Czech Academy of Sciences Publication Activity Database

    Němeček, J.; Denk, F.; Zlámal, Petr

    2015-01-01

    Roč. 267, September (2015), s. 506-516 ISSN 0096-3003 R&D Projects: GA ČR(CZ) GAP105/12/0824 Institutional support: RVO:68378297 Keywords : closed-cell aluminium foam * Alporas * multiscale modeling * homogenization * FFT * finite element modeling Subject RIV: JI - Composite Materials Impact factor: 1.345, year: 2015 http://www.sciencedirect.com/science/article/pii/S0096300315001162

  11. Texture development during recrystallization of aluminium containing large particles

    DEFF Research Database (Denmark)

    Juul Jensen, Dorte; Hansen, Niels; Humphreys, F. J.

    1985-01-01

    The recrystallization process in heavily deformed commercially pure aluminium containing large intermetallic particles was studied by in situ neutron diffraction texture measurements and various microscopical techniques including texture measurements in local areas and simultaneous determination...... of orientations takes place close to larger particles or clusters of particles early in the recrystallization process. The texture of fully recrystallized material, however, contains only a relatively weak random component showing that the randomisation effect of the particles was limited. This was ascribed...

  12. Development of Niobium Boron grain retainer for aluminium silicon alloys

    OpenAIRE

    Nowak, Magdalena

    2011-01-01

    This thesis was submitted for the degree of Doctor of Philosophy and awarded by Brunel University Aluminium castings with a large grain structure have poor mechanical properties which are primarily due to casting defects as opposed to fine grain structure. The grain refinement practice using chemical addition is well established for wrought alloys, however in the case of casting alloys, the practice of adding grain refiners and the impact on castability is not well established. The additio...

  13. Study of twist boundaries in aluminium. Structure and intergranular diffusion

    International Nuclear Information System (INIS)

    Lemuet, Daniel

    1981-01-01

    This research thesis addresses the study of grain boundaries in oriented crystals, and more particularly the systematic calculation of intergranular structures and energies of twist boundaries of <001> axis in aluminium, the determination of intergranular diffusion coefficients of zinc in a set of twist bi-crystals of same axis encompassing a whole range of disorientations, and the search for a correlation between these experimental results and calculated structures

  14. Neutron diffraction study at 0.3 K of the magnetic properties of rare-earth aluminium or gallium garnets; Etude par diffraction des neutrons a 0,3 K des proprietes magnetiques de grenats de terre rare et d'aluminium ou de gallium

    Energy Technology Data Exchange (ETDEWEB)

    Hammann, J. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1969-03-01

    In order to study ordered magnetic states below 1.5 deg. K by neutron diffraction measurements, a helium-3 cryostat has been realised in which the thermalization of a great quantity of powdered sample is performed by a helium-4 superfluid film, and which leaves the possibility of applying an external magnetic field. We thus studied essentially the magnetic phase transitions of rare-earth aluminium or gallium garnets. First we determined the antiferromagnetic structures of the erbium gallium garnet (T{sub N} = 0.79 deg. K) and of the neodymium gallium garnet (T{sub N} = 0.516 deg. K). The metamagnetic behavior of the erbium gallium garnet has been observed and compared to that of the dysprosium aluminium garnet. Second we considered the 'non-Kramers' ions Tb{sup 3+} and Ho{sup 3+} in the aluminium garnets. In this case, only two single ground states (well isolated from upper levels) have to be considered. A molecular field model with purely magnetic dipolar interactions, leads then to the existence of magnetic phase transition with antiferromagnetic ordering. This has been observed for the terbium-aluminium garnet below T{sub N} 1.35 deg. K and for the holmium-aluminium garnet below T{sub N} {approx} 0.98 deg. K. (author) [French] Afin d'acceder a l'etude par diffraction des neutrons des etats magnetiques ordonnes en-dessous de 1,5 deg. K, nous avons realise un cryostat a helium-3 qui assure la mise en temperature de la quantite importante d'echantillon en poudre a l'aide d'un film d'helium-4-superfluide, et qui laisse la possibilite d'application d'un champ magnetique exterieur. Nous avons essentiellement etudie avec cette technique les transitions de phase magnetique de grenats de terre rare et d'aluminium ou de gallium. C'est ainsi qu'on a determine l'ordre antiferromagnetique dans les grenats de gallium-erbium (T{sub N} = 0,79 deg. K) et de gallium-neodyme (T{sub N} = 0,516 deg. K). Le

  15. Aluminium and Aroma Compound Concentration in Beer During Storage at Different Temperatures

    Directory of Open Access Journals (Sweden)

    Marija Soldo Gjeldum

    2006-01-01

    Full Text Available Problem of aluminium in beer has been elaborated in several papers over the last decade. However, the effect of aluminium on organoleptic properties of beer has been observed in few papers where it has been stated that aluminium gives beer a »metallic« and bitter flavour without any observations on particular aroma compound changes. Also, the number of reports on precise changes of aroma components throughout different storage conditions is surprisingly scarce. In order to investigate the changes of aluminium concentration along with aroma compound changes, graphite furnace-atomic absorption spectrophotometry (GF-AAS with Zeeman background correction and gas chromatography with static headspace sampler (GC-HSS were used in this work. Analyses were conducted periodically throughout seven months of storage on three different brands of beer from name breweries. Samples were taken before and after filling in aluminium cans. One part of samples was stored in a refrigerator (4 °C and the other in a thermostatic chamber (22 °C. The effects of beer brand and storage conditions on aluminium concentration and level of aroma compounds were measured. To prove the effect of aluminium concentration on the changes of aroma compounds, the adequate level of aluminium sulphate was added to bottled beer samples stored at 28 °C. Although different beer types showed significantly different aluminium concentration, it could be the result of other factors (different batches of identical beer type showed significantly different aluminium concentration as well. Samples that were stored in the refrigerator were protected from aluminium migration from the can to the beer and showed increased aroma stability. Level of aroma constituents of analyzed beer brands was significantly different. Elevated aluminium concentration did not have any noticeable effect on the level of aroma compounds in beer samples stored at 28 °C.

  16. Physical and chemical bases of complex processing of aluminium production wastes

    International Nuclear Information System (INIS)

    Ruziev, D.R.

    1998-01-01

    The purpose of the present work is development of scientific bases of processing of aluminium production wastes. For this it was necessary consider following base processes: water extraction of useful components from mud of aluminium production; receiving of soda ash, liquid glass, glaze, cryolite and alumina from aluminium production wastes; remove of carbon from mud and screening of refuse tip by flotation and incineration method

  17. Anisotropic behaviour law for sheets used in stamping: A comparative study of steel and aluminium

    OpenAIRE

    Sinou, Jean-Jacques; Macquaire, Bruno

    2008-01-01

    International audience; For a car manufacturer, reducing the weight of vehicles is an obvious aim. Replacing steel by aluminium moves towards that goal. Unfortunately, aluminium's stamping numerical simulation results are not yet as reliable as those of steel. Punch-strength and spring-back phenomena are not correctly described. This study on aluminium validates the behaviour law Hill 48 quadratic yield criterion with both isotropic and kinematic hardening. It is based on the yield surface an...

  18. The effects of radiation on aluminium alloys in the core of energy nuclear reactors

    International Nuclear Information System (INIS)

    Petrossian, V.G.

    1995-01-01

    One of the attractive directions in the worldwide practice of nuclear installations is the replacement of expensive zirconium alloy with more cheap materials, particularly aluminium allo. For Heat Supply Nuclear Plants (HSNP) with approximately 473 K core temperatures, the use of heat-resistant aluminium alloys seems to be reasonable. The present work is concerned with the studies on radiation effects on aluminium alloy, and interaction between the alloy and coolant in the reactor core. (author). 2 refs., 3 figs., 1 tab

  19. Grain Refinement of Commercial EC Grade 1070 Aluminium Alloy for Electrical Application

    OpenAIRE

    Hassanabadi, Massoud

    2015-01-01

    The aluminium alloys for electrical conductivity applications are generally not grain refinedsince the addition of grain refiners drops the electrical conductivity by introducing impuritiesinto the melt. Non-grain refined aluminium may lead to bar fracture and cracks during themetalworking process. The present study focuses to find an optimum balance between the grain refiner addition andthe electrical conductivity of commercial EC grade 1070 aluminium alloy for electricalapplication. In orde...

  20. Machinability of magnesium and aluminium alloys. Part I: cutting resistance

    International Nuclear Information System (INIS)

    Balout, B.; Songmene, V.; Masounave, J.

    2002-01-01

    Aluminium (2.7 g/cm 3 ) and magnesium (1.7 g/cm 3 ) are two competing light metals with similar mechanical properties and excellent possibilities for recycling. The forming of magnesium is often seen as an impediment to its use. New forming techniques using magnesium shavings are being developed, particularly in Japan. The machining of magnesium alloys by removal of metal raises safety concerns (risk of fire), which limits many potential applications of magnesium. The purpose of this work is to clarify and compare the machining properties of these two types of metal and better understand the mechanisms that may explain the differences in behaviour. Such a comparison could eventually provide an estimate of the cost of producing shavings for the manufacture of aluminium and magnesium parts through forging and extrusion, which would limit environmental pollution. Based on an analysis of cutting resistance during machining, it was demonstrated that magnesium alloys are easier to machine than similar aluminium alloys. Magnesium shavings are shorter than those of 6061-T6, but are especially more regular than those of A356, and their size is independent of cutting speed. It was also demonstrated that the fragility of materials can be characterized based on the results of cutting resistance produced during drilling

  1. Recycling of aluminium scrap for secondary Al-Si alloys.

    Science.gov (United States)

    Velasco, Eulogio; Nino, Jose

    2011-07-01

    An increasing amount of recycled aluminium is going into the production of aluminium alloy used for automotive applications. In these applications, it is necessary to control and remove alloy impurities and inclusions. Cleaning and fluxing processes are widely used during processing of the alloys for removal of inclusions, hydrogen and excess of magnesium. These processes use salt fluxes based in the system NaCl-KCl, injection of chlorine or mixture of chlorine with an inert gas. The new systems include a graphite wand and a circulation device to force convection in the melt and permit the bubbling and dispersion of reactive and cleaning agents. This paper discusses the recycling of aluminium alloys in rotary and reverberatory industrial furnaces. It focuses on the removal of magnesium during the melting process. In rotary furnaces, the magnesium lost is mainly due to the oxidation process at high temperatures. The magnesium removal is carried out by the reaction between chlorine and magnesium, with its efficiency associated to kinetic factors such as concentration of magnesium, mixing, and temperature. These factors are also related to emissions generated during the demagging process. Improvements in the metallic yield can be reached in rotary furnaces if the process starts with a proper salt, with limits of addition, and avoiding long holding times. To improve throughput in reverberatories, start the charging with high magnesium content material and inject chlorine gas if the molten metal is at the right temperature. Removal of magnesium through modern technologies can be efficiently performed to prevent environmental problems.

  2. Simulation of thin aluminium-foil in the packaging industry

    Science.gov (United States)

    Eskil, Andreasson; Lindström, Tommy; Käck, Britta; Malmberg, Christoffer; Asp, Ann-Magret

    2017-10-01

    This work present an approach of how to account for the anisotropic mechanical material behaviour in the simulation models of the thin aluminium foil layer (≈10 µm) used in the Packaging Industry. Furthermore, the experimental results from uniaxial tensile tests are parameterised into an analytical expression and the slope of the hardening subsequently extended way beyond the experimental data points. This in order to accommodate the locally high stresses present in the experiments at the neck formation. An analytical expression, denominated Ramberg-Osgood, is used to describe the non-linear mechanical behaviour. Moreover it is possible with a direct method to translate the experimental uniaxial tensile test results into useful numerical material model parameters in Abaqus™. In addition to this the extended material behaviour including the plastic flow i.e. hardening, valid after onset of localisation, the described procedure can also capture the microscopic events, i.e. geometrical thinning, ongoing in the deformation of the aluminium foil. This method has earlier successfully been applied by Petri Mäkelä for paperboard material [1]. The engineering sound and parameterised description of the mechanical material behaviour facilitates an efficient categorisation of different aluminium foil alloys and aid the identification of the correct anisotropic (RD/TD/45°) mechanical material behaviour derived from the physical testing.

  3. Aluminium intake by INAA of hair: The aerosol intoxication pathway

    International Nuclear Information System (INIS)

    Preoteasa, E.A.; Ionescu, A.; Pantelica, A.; Salagean, M.; Rusu, C.; Moldovan, O.; Ghiordunwscu, Vl.; Marusca, D.

    1997-01-01

    Aluminium is present in healthy human organisms in concentrations that appear to be neither useful nor noxious. However, long term higher Al levels can produce severe bone, renal and cerebral troubles. Here we report the results of the first investigation using the Instrumental Neutron Activation Analysis of human hair aimed to assess the Al contamination in workers from aluminium industry due to aerosol inhalation. Seventy five subjects working at 'Alprom' Inc., Slatina, Romania aluminium processing plant were included in this study. The exposed subjects were casters, crane operators and rolling mill operators. Hair samples were washed with acetone-water-water-water-acetone using bi-distilled water and re-distilled-purified p.a. grade acetone and irradiated for 3 min at a thermal neutron flux of 2.3 x 10 12 n/cm 2 s in the VVR-S reactor. Student's t-test showed the arithmetical mean values of all exposed groups to differ of the control group's one with a good statistical confidence level. In most workers the Al concentration in hair is 2 times higher than normal but in one third of the casters and in two of the rolling mill operators it is on average up to 7 times higher. Substantial Al overload can cause severe osteoporosis or encephalopathies even after retirement from activity. Protection filtering masks and medical therapy based on strong chelant drug deferoxamine are recommended, (authors)

  4. Aluminium base amorphous and crystalline alloys with Fe impurity

    International Nuclear Information System (INIS)

    Sitek, J.; Degmova, J.

    2006-01-01

    Aluminium base alloys show remarkable mechanical properties, however their low thermal stability still limits the technological applications. Further improvement of mechanical properties can be reached by partial crystallization of amorphous alloys, which gives rise to nanostructured composites. Our work was focused on aluminium based alloys with Fe, Nb and V additions. Samples of nominal composition Al 90 Fe 7 Nb 3 and Al 94 Fe 2 V 4 were studied in amorphous state and after annealing up to 873 K. From Moessbauer spectra taken on the samples in amorphous state the value of f-factor was determined as well as corresponding Debye temperatures were calculated. Annealing at higher temperatures induced nano and microcrystalline crystallization. Moessbauer spectra of samples annealed up to 573 K are fitted only by distribution of quadrupole doublets corresponding to the amorphous state. An increase of annealing temperature leads to the structural transformation, which consists in growth of nanometer sized aluminium nuclei. This is partly reflected in Moessbauer parameters. After annealing at 673 K intermetallic phase Al 3 Fe and other Al-Fe phases are created. In this case Moessbauer spectra are fitted by quadrupole doublets. During annealing up to 873 K large grains of Fe-Al phases are created. (authors)

  5. Toxicity of indium arsenide, gallium arsenide, and aluminium gallium arsenide.

    Science.gov (United States)

    Tanaka, Akiyo

    2004-08-01

    Gallium arsenide (GaAs), indium arsenide (InAs), and aluminium gallium arsenide (AlGaAs) are semiconductor applications. Although the increased use of these materials has raised concerns about occupational exposure to them, there is little information regarding the adverse health effects to workers arising from exposure to these particles. However, available data indicate these semiconductor materials can be toxic in animals. Although acute and chronic toxicity of the lung, reproductive organs, and kidney are associated with exposure to these semiconductor materials, in particular, chronic toxicity should pay much attention owing to low solubility of these materials. Between InAs, GaAs, and AlGaAs, InAs was the most toxic material to the lung followed by GaAs and AlGaAs when given intratracheally. This was probably due to difference in the toxicity of the counter-element of arsenic in semiconductor materials, such as indium, gallium, or aluminium, and not arsenic itself. It appeared that indium, gallium, or aluminium was toxic when released from the particles, though the physical character of the particles also contributes to toxic effect. Although there is no evidence of the carcinogenicity of InAs or AlGaAs, GaAs and InP, which are semiconductor materials, showed the clear evidence of carcinogenic potential. It is necessary to pay much greater attention to the human exposure of semiconductor materials.

  6. Effects of aluminium oxide nanoparticles on bacterial growth

    Directory of Open Access Journals (Sweden)

    Doskocz Nina

    2017-01-01

    Full Text Available Production and wide application of nanomaterials have led to nanotechnology development but their release to environment and the induction of toxic reactions, affects the natural microbial communities. Therefore, studies on the impact of nanoparticles on microorganisms and environment are required and needed. The aim of this study was to assess the impact of aluminium oxide nanoparticles on the growth of Pseudomonas putida. To compare the harmfulness of different forms of aluminium oxide, the ecotoxicity of its macro-forms was also evaluated in the study. Research showed that the exposure to nanoparticles can negatively influence microorganisms. The EC50-16h determined in this study was 0.5 mg/l, and NOEC equaled 0.19 mg/l. Nano-Al2O3 proved to be more toxic to P. putida than aluminium oxide. This indicates that the nano-form of a given substance demonstrates different properties and may constitute a far greater danger for the environment than the same substance in the large form. According to EU and US EPA criteria, nano-Al2O3 proved to be very toxic and highly toxic, respectively. Changes in bacterial communities caused by nanoparticles may affect the normal biological, chemical and nutrient cycle in the ecosystem and the effect triggered by nanomaterials in relation to other organisms is unpredictable.

  7. Spectroscopic diagnostics of plasma during laser processing of aluminium

    Science.gov (United States)

    Lober, R.; Mazumder, J.

    2007-10-01

    The role of the plasma in laser-metal interaction is of considerable interest due to its influence in the energy transfer mechanism in industrial laser materials processing. A 10 kW CO2 laser was used to study its interaction with aluminium under an argon environment. The objective was to determine the absorption and refraction of the laser beam through the plasma during the processing of aluminium. Laser processing of aluminium is becoming an important topic for many industries, including the automobile industry. The spectroscopic relative line to continuum method was used to determine the electron temperature distribution within the plasma by investigating the 4158 Å Ar I line emission and the continuum adjacent to it. The plasmas are induced in 1.0 atm pure Ar environment over a translating Al target, using f/7 and 10 kW CO2 laser. Spectroscopic data indicated that the plasma composition and behaviour were Ar-dominated. Experimental results indicated the plasma core temperature to be 14 000-15 300 K over the incident range of laser powers investigated from 5 to 7 kW. It was found that 7.5-29% of the incident laser power was absorbed by the plasma. Cross-section analysis of the melt pools from the Al samples revealed the absence of any key-hole formation and confirmed that the energy transfer mechanism in the targets was conduction dominated for the reported range of experimental data.

  8. Laser synthesis of aluminium nanoparticles in biocompatible polymer solutions

    Science.gov (United States)

    Singh, Rina; Soni, R. K.

    2014-08-01

    Pulsed laser ablation of Aluminium (Al) in pure water rapidly forms a thin alumina (Al2O3) layer which drastically modifies surface plasmon resonance (SPR) absorption characteristics in deep-UV region. Initially, pure aluminium nanoparticles (NPs) are generated in water without any stabilizers or surfactants at low laser fluence which gradually transform to stable Al-Al2O3 core-shell nanostructure with increasing either residency time or fluence. The role of laser wavelength and fluence on the SPR properties and oxidation characteristics of Al NPs has been investigated in detail. We also present a one-step in situ synthesis of oxide-free stable Al NPs in biocompatible polymer solutions using laser ablation in liquid method. We have used nonionic polymers (PVP, PVA and PEG) and anionic surfactant (SDS) stabilizer to suppress the Al2O3 formation and studied the effect of polymer functional group, polymeric chain length, polymer concentration and anionic surfactant on the incipient embryonic aluminium particles and their sizes. The different functional groups of polymers resulted in different oxidation states of Al. PVP and PVA polymers resulted in pure Al NPs; however, PEG and SDS resulted in alumina-modified Al NPs. The Al nanoparticles capped with PVP, PVA, and PEG show a good correlation between nanoparticle stability and monomeric length of the polymer chain.

  9. Improving the wettability of 2024 aluminium alloy by means of cold plasma treatment

    Science.gov (United States)

    Polini, W.; Sorrentino, L.

    2003-05-01

    Aluminium alloys are heavily used to manufacture structural parts in the aeronautic industry because of its lightness and its corrosion resistance. These alloys are successfully used in other industrial fields too, such as railway, automotive and naval industries. The need to contrast the severe use conditions and the heavy stresses developing in aeronautic field implies to protect the surfaces of the structures in aluminium alloy by any deterioration. To preserve by deterioration, it is necessary to make aluminium more suitable to be coated by protective paint. In the aeronautic industry, a complex and critical process is used in order to enhance both wettability and adhesive properties of aluminium alloy surfaces. Cold plasma treatment represents an efficient, clean and economic alternative to activate aluminium surfaces. The present work deals with air cold plasma treatment of 2024 aluminium alloy surfaces. The influence of dc electrical discharge cold plasma parameters on wettability of 2024 aluminium alloy surfaces has been studied. A set of process variables (voltage, time and air flow rate) has been identified and used to conduct some experimental tests on the basis of design of experiment (DOE) techniques. The experimental results show that the proposed plasma process may considerably increase aluminium alloy wettability. These results represent the first step in trying to optimise the aluminium adhesion by means of this non-conventional manufacturing process.

  10. Spectral changes of brain activity in rat offspring exposed to aluminium during gestation and lactation

    Directory of Open Access Journals (Sweden)

    Martać L.

    2010-01-01

    Full Text Available Exposure to aluminium during gestation causes changes in mammalian brain development and behavior. Our aim was to perform spectral analysis on electrocortical activity of Sprague Dawley male pups (30±3 days of age whose mothers were treated with aluminium during gestation and lactation. There was a higher presence of power spectra in the delta range of parietal electrocortical activity, a lower presence in the theta range and increased values of the parameter DT as the ratio of delta to theta range in pups indirectly exposed to aluminium (whose mothers were drinking a 0.5% water solution of aluminium chloride during the gestation and lactation periods, compared to controls.

  11. Neuroprotective effect of Allium cepa L. in aluminium chloride induced neurotoxicity.

    Science.gov (United States)

    Singh, Tanveer; Goel, Rajesh Kumar

    2015-07-01

    The present study was envisaged to investigate the neuroprotective potential of Allium cepa (A. cepa) in aluminium chloride induced neurotoxicity. Aluminium chloride (50 mg/kg/day) was administered orally in mice supplemented with different doses of A. cepa hydroethanolic extract for a period of 60 days. Various behavioural, biochemical and histopathological parameters were estimated in aluminium exposed animals. Chronic aluminium administration resulted in significant motor incoordination and memory deficits, which were also endorsed biochemically as there was increased oxidative stress as well as elevated acetylcholinesterase (AChE) and aluminium levels in the brain. Supplementation with A. cepa in aluminium exposed animals significantly improved muscle coordination and memory deficits as well as reduced oxidative stress, AChE and decreased abnormal aluminium deposition in the brain. Histopathologically, there was marked deterioration visualized as decreased vacuolated cytoplasm as well as decreased pyramidal cells in the hippocampal area of mice brain which were found to be reversed with A. cepa supplementation. Administration of BADGE (PPARγ antagonist) in aluminium exposed animals reversed the neuroprotective potential of A. cepa as assessed with various behavioural, biochemical, neurochemical and histopathological estimations. In conclusion, finding of this study suggested significant neuroprotective potential of A. cepa in aluminium induced neurotoxicity. Further, the role of PPARγ receptor agonism has also been suggested as a putative neuroprotective mechanism of A. cepa, which needs further studies for confirmation. Copyright © 2015 Elsevier Inc. All rights reserved.

  12. Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

    Science.gov (United States)

    Yang, Mei; Jiang, Lixin; Huang, Huiping; Zeng, Shengbo; Qiu, Fen; Yu, Miao; Li, Xiaorong; Wei, Sheng

    2014-01-01

    Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg), fried twisted cruller (median, 466.0 mg/kg), shell (median, 107.1 mg/kg). The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake). But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week) than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

  13. Dietary exposure to aluminium and health risk assessment in the residents of Shenzhen, China.

    Directory of Open Access Journals (Sweden)

    Mei Yang

    Full Text Available Although there are great changes of dietary in the past few decades in China, few are known about the aluminium exposure in Chinese diet. The aim of this study is to systematically evaluate the dietary aluminium intake level in residents of Shenzhen, China. A total of 853 persons from 244 household were investigated their diet by three days food records. Finally, 149 kinds of foods in 17 food groups were selected to be the most consumed foods. From them, 1399 food samples were collected from market to test aluminium concentration. High aluminium levels were found in jellyfish (median, 527.5 mg/kg, fried twisted cruller (median, 466.0 mg/kg, shell (median, 107.1 mg/kg. The Shenzhen residents' average dietary aluminium exposure was estimated at 1.263 mg/kg bw/week which is lower than the PTWI (provisional tolerable weekly intake. But 0-2 and 3-13 age groups have the highest aluminium intake exceeding the PTWI (3.356 mg/kg bw/week and 3.248 mg/kg bw/week than other age groups. And the main dietary aluminium exposure sources are fried twisted cruller, leaf vegetables and bean products. Our study suggested that even three decades rapid economy development, children in Shenzhen still have high dietary aluminium exposure risk. How to control high dietary aluminium exposure still is a great public health challenge in Shenzhen, China.

  14. A study on the role of diboride in the heterogeneous nucleation of aluminium

    International Nuclear Information System (INIS)

    Suarez, O. M.

    2004-01-01

    The intangible role of titanium and aluminium diboride in the nucleation of aluminium was re-examined. Two different techniques, complemented with scanning electron microscopy, allowed determining the stability of the diboride in the presence of titanium tri aluminides and liquid aluminium phases. Through rapid scintillated quenching the high temperature diboride were retained and studied. Then, in a diffusion couple, the reactivity of such diboride was tested in contact with pure titanium tri aluminide. It is proposed that a ternary diboride acts as the main catalytic particle in the crystallization of aluminium alloys with refined grains. (Author) 27 refs

  15. Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

    Science.gov (United States)

    2011-01-01

    Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer), which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more expensive binders and increasing

  16. Comparison of the x-ray attenuation properties of breast calcifications, aluminium, hydroxyapatite and calcium oxalate.

    Science.gov (United States)

    Warren, L M; Mackenzie, A; Dance, D R; Young, K C

    2013-04-07

    Aluminium is often used as a substitute material for calcifications in phantom measurements in mammography. Additionally, calcium oxalate, hydroxyapatite and aluminium are used in simulation studies. This assumes that these materials have similar attenuation properties to calcification, and this assumption is examined in this work. Sliced mastectomy samples containing calcification were imaged at ×5 magnification using a digital specimen cabinet. Images of the individual calcifications were extracted, and the diameter and contrast of each calculated. The thicknesses of aluminium required to achieve the same contrast as each calcification when imaged under the same conditions were calculated using measurements of the contrast of aluminium foils. As hydroxyapatite and calcium oxalate are also used to simulate calcifications, the equivalent aluminium thicknesses of these materials were also calculated using tabulated attenuation coefficients. On average the equivalent aluminium thickness was 0.85 times the calcification diameter. For calcium oxalate and hydroxyapatite, the equivalent aluminium thicknesses were 1.01 and 2.19 times the thickness of these materials respectively. Aluminium and calcium oxalate are suitable substitute materials for calcifications. Hydroxyapatite is much more attenuating than the calcifications and aluminium. Using solid hydroxyapatite as a substitute for calcification of the same size would lead to excessive contrast in the mammographic image.

  17. Protective effect of curcumin (Curcuma longa), against aluminium toxicity: Possible behavioral and biochemical alterations in rats.

    Science.gov (United States)

    Kumar, Anil; Dogra, Samrita; Prakash, Atish

    2009-12-28

    Aluminium is a potent neurotoxin and has been associated with Alzheimer's disease (AD) causality for decades. Prolonged aluminium exposure induces oxidative stress and increases amyloid beta levels in vivo. Current treatment modalities for AD provide only symptomatic relief thus necessitating the development of new drugs with fewer side effects. The aim of the study was to demonstrate the protective effect of chronic curcumin administration against aluminium-induced cognitive dysfunction and oxidative damage in rats. Aluminium chloride (100 mg/kg, p.o.) was administered to rats daily for 6 weeks. Rats were concomitantly treated with curcumin (per se; 30 and 60 mg/kg, p.o.) daily for a period of 6 weeks. On the 21st and 42nd day of the study behavioral studies to evaluate memory (Morris water maze and elevated plus maze task paradigms) and locomotion (photoactometer) were done. The rats were sacrificed on 43rd day following the last behavioral test and various biochemical tests were performed to assess the extent of oxidative damage. Chronic aluminium chloride administration resulted in poor retention of memory in Morris water maze, elevated plus maze task paradigms and caused marked oxidative damage. It also caused a significant increase in the acetylcholinesterase activity and aluminium concentration in aluminium treated rats. Chronic administration of curcumin significantly improved memory retention in both tasks, attenuated oxidative damage, acetylcholinesterase activity and aluminium concentration in aluminium treated rats (Paluminium-induced cognitive dysfunction and oxidative damage.

  18. Do aluminium-based phosphate binders continue to have a role in contemporary nephrology practice?

    Directory of Open Access Journals (Sweden)

    van Eps Carolyn L

    2011-05-01

    Full Text Available Abstract Background Aluminium-containing phosphate binders have long been used for treatment of hyperphosphatemia in dialysis patients. Their safety became controversial in the early 1980's after reports of aluminium related neurological and bone disease began to appear. Available historical evidence however, suggests that neurological toxicity may have primarily been caused by excessive exposure to aluminium in dialysis fluid, rather than aluminium-containing oral phosphate binders. Limited evidence suggests that aluminium bone disease may also be on the decline in the era of aluminium removal from dialysis fluid, even with continued use of aluminium binders. Discussion The K/DOQI and KDIGO guidelines both suggest avoiding aluminium-containing binders. These guidelines will tend to promote the use of the newer, more expensive binders (lanthanum, sevelamer, which have limited evidence for benefit and, like aluminium, limited long-term safety data. Treating hyperphosphatemia in dialysis patients continues to represent a major challenge, and there is a large body of evidence linking serum phosphate concentrations with mortality. Most nephrologists agree that phosphate binders have the potential to meaningfully reduce mortality in dialysis patients. Aluminium is one of the cheapest, most effective and well tolerated of the class, however there are no prospective or randomised trials examining the efficacy and safety of aluminium as a binder. Aluminium continues to be used as a binder in Australia as well as some other countries, despite concern about the potential for toxicity. There are some data from selected case series that aluminium bone disease may be declining in the era of reduced aluminium content in dialysis fluid, due to rigorous water testing. Summary This paper seeks to revisit the contemporary evidence for the safety record of aluminium-containing binders in dialysis patients. It puts their use into the context of the newer, more

  19. Silane pre-treatments on copper and aluminium

    International Nuclear Information System (INIS)

    Deflorian, F.; Rossi, S.; Fedrizzi, L.

    2006-01-01

    A large part of aluminium products are coated with an organic layer in order to improve the corrosion resistance. Copper surfaces are also sometimes protected with an organic coating to improve the durability or the aesthetic properties. Examples of industrial applications are household appliances and heat exchanger components. For these applications it is not rare to have the industrial need to treat at the same time components made of aluminium and copper. In order to extend the service life of the organic coated copper a specific surface pre-treatment is often required. Nevertheless, probably because of the limited market of this application, no specific pre-treatments for copper are industrially developed, with the exception of cleaning procedures, but simply extensions of existing pre-treatments optimised for other metals (aluminium, zinc) are used. The application of silane pre-treatments as adhesion promoters for organic coated metals is remarkably increasing in the last decade, because silanes offer very good performance together with high environmental compatibility. The idea is therefore to try to develop a specific silane based pre-treatment for copper. The starting point is the existing silane products for aluminium, optimising the composition and the application conditions (concentration, temperature, pH of the bath, etc.) in order to develop a high performance copper alloy pre-treatment increasing the protective properties and the adhesion of a successively applied organic coating. Moreover these pre-treatments could be used for aluminium alloys too and therefore could be suggested for multi-metals components. The deposits were analysed using FTIR spectroscopy and optical and electron microscopic observations. A careful electrochemical characterisation, mainly by electrochemical impedance spectroscopy measurements (EIS) was carried out to highlight the presence of silane and to evaluate the performance of the different deposits. In order to study an

  20. Human biomonitoring of aluminium after a single, controlled manual metal arc inert gas welding process of an aluminium-containing worksheet in nonwelders.

    Science.gov (United States)

    Bertram, Jens; Brand, Peter; Hartmann, Laura; Schettgen, Thomas; Kossack, Veronika; Lenz, Klaus; Purrio, Ellwyn; Reisgen, Uwe; Kraus, Thomas

    2015-10-01

    Several existing field studies evaluate aluminium welding works but no thoroughly controlled exposure scenario for welding fume has been described yet. This study provides information about the uptake and elimination of aluminium from welding fumes under controlled conditions. In the Aachen Workplace Simulation Laboratory, we are able to generate welding fumes of a defined particle mass concentration. We exposed 12, until then occupationally unexposed participants with aluminium-containing welding fumes of a metal inert gas (MIG) welding process of a total dust mass concentration of 2.5 mg/m(3) for 6 h. Room air filter samples were collected, and the aluminium concentration in air derived. Urine and plasma samples were collected directly before and after the 6-h lasting exposure, as well as after 1 and 7 days. Human biomonitoring methods were used to determine the aluminium content of the samples with high-resolution continuum source atomic absorption spectrometry. Urinary aluminium concentrations showed significant changes after exposure compared to preexposure levels (mean t(1) (0 h) 13.5 µg/L; mean t(2) (6 h) 23.5 µg/L). Plasma results showed the same pattern but pre-post comparison did not reach significance. We were able to detect a significant increase of the internal aluminium burden of a single MIG aluminium welding process in urine, while plasma failed significance. Biphasic elimination kinetic can be observed. The German BAT of 60 µg/g creatinine was not exceeded, and urinary aluminium returned nearly to baseline concentrations after 7 days.

  1. Structural and magnetic properties of nickel nanowires grown in porous anodic aluminium oxide template by electrochemical deposition technique

    Science.gov (United States)

    Nugraha Pratama, Sendi; Kurniawan, Yudhi; Muhammady, Shibghatullah; Takase, Kouichi; Darma, Yudi

    2018-03-01

    We study the formation of nickel nanowires (Ni NWs) grown in porous anodic aluminium oxide (AAO) template by the electrochemical deposition technique. Here, the initial AAO template was grown by anodization of aluminium substrate in sulphuric acid solution. The cross-section, crystal structure, and magnetic properties of Ni NWs system were characterized by field-emission SEM, XRD, and SQUID. As a result, the highly-ordered Ni NWs are observed with the uniform diameter of 27 nm and the length from 31 to 163 nm. Based on XRD spectra analysis, Ni NWs have the face-centered cubic structure with the lattice parameter of 0.35 nm and average crystallite size of 17.19 nm. From SQUID measurement at room temperature, by maintaining the magnetic field perpendicular to Ni NWs axis, the magnetic hysteresis of Ni NWs system show the strong ferromagnetism with the coercivity and remanence ratio of ∼148 Oe and ∼0.23, respectively. The magnetic properties are also calculated by means of generalized gradient approximation methods. From the calculation result, we show that the ferromagnetism behavior comes from Ni NWs without any contribution from AAO template or the substrate. This study opens the potential application of Ni NWs system for novel functional magnetic devices.

  2. Solution phase chemical synthesis of nano aluminium particles stabilized in poly(vinylpyrrolidone) and poly(methylmethacrylate) matrices.

    Science.gov (United States)

    Ghanta, Sekher Reddy; Muralidharan, Krishnamurthi

    2010-06-01

    The reduction of aluminium trichloride by lithium aluminium hydride in the presence of poly(vinylpyrrolidone) or poly(methylmethacrylate) in mesitylene yielded nano aluminium particles in the matrices of respective polymers. Solution phase synthesis methodology was used successfully to produce composites of various Al/polymer ratios. The composites were characterized by powder XRD patterns and 27Al-NMR with MAS spectroscopic study. The method was useful to produce up to 10 g of nano aluminium that were pure and stable.

  3. Microstructures of alloyed and dispersed hard particles in the aluminium surface

    CSIR Research Space (South Africa)

    Pityana, S

    2010-03-01

    Full Text Available Laser surface alloying of A1200 aluminium alloy was carried out using a 4.4 kW Nd:YAG laser. Powder mixtures of SiC and TiC hard particles were injected into the laser generated melt pool on the aluminium substrate using a commercial powder feeder...

  4. Lewis Acid-Base Properties of a Low Carbon Aluminium Killed Steel ...

    African Journals Online (AJOL)

    NJD

    a particular use.7–9 Low carbon aluminium killed (LCAK) steel. (steel deoxidized with aluminium in order to reduce the oxygen content to a minimum so that no reaction occurs between carbon and oxygen during solidification) was considered. This type of steel is used mostly by the packaging industry. Organic coatings.

  5. Electron Conditioning of Technical Aluminium Surfaces: Effect on the Secondary Electron Yield

    Energy Technology Data Exchange (ETDEWEB)

    Le Pimpec, F.

    2004-12-13

    The effect of electron conditioning on commercially aluminium alloys 1100 and 6063 were investigated. Contrary to the assumption that electron conditioning, if performed long enough, can reduce and stabilize the SEY to low values (< 1.3, value of many pure elements [1] ), the SEY of aluminium did not go lower than 1.8. In fact, it reincreases with continued electron exposure dose.

  6. Aluminium in an ocean general circulation model compared with the West Atlantic Geotraces cruises

    NARCIS (Netherlands)

    van Hulten, M. M. P.; Sterl, A.; Tagliabue, A.; Dutay, J. -C.; Gehlen, M.; de Baar, H. J. W.; Middag, R.

    2013-01-01

    A model of aluminium has been developed and implemented in an Ocean General Circulation Model (NEMO-PISCES). In the model, aluminium enters the ocean by means of dust deposition. The internal oceanic processes are described by advection, mixing and reversible scavenging. The model has been evaluated

  7. The role of magnesium in the electrochemical behaviour of 5XXX aluminium-magnesium alloys

    NARCIS (Netherlands)

    Flores Ramirez, J.R.

    2006-01-01

    An investigation concerning the effects of magnesium on the intergranular corrosion susceptibility of AA5XXX aluminium alloys was carried out. In the present work, magnesium is found to be highly mobile in the bulk metal as well as in the aluminium oxide. This mobility is also found to be dependent

  8. A regionally-linked, dynamic material flow modelling tool for rolled, extruded and cast aluminium products

    DEFF Research Database (Denmark)

    Bertram, M.; Ramkumar, S.; Rechberger, H.

    2017-01-01

    of regional stocks and flows of rolled, extruded and casting alloys across space and over time, giving the industry the ability to evaluate the potential to recycle aluminium scrap most efficiently. The International Aluminium Institute will update the tool annually and publish a visualisation of results...... tonnes), other rolled scrap (6 million tonnes), extruded scrap (4 million tonnes) and other scrap (2 million tonnes)....

  9. Void formation in pure aluminium irradiated with high-energetic electron beams and gamma-quanta

    DEFF Research Database (Denmark)

    Gan, V. V.; Ozhigou, L. S.; Yamnitsky, V. A.

    1983-01-01

    The spatial distribution of displaced atoms and helium atoms and also the spectra of damaging energies of primary displaced atoms in a thick aluminium target irradiated with electrons of 225 MeV energy were calculated. Pure aluminium (99.9999%) irradiated up to 0.04 dose was studied by electron...

  10. Neuroprotective role of Convolvulus pluricaulis on aluminium induced neurotoxicity in rat brain.

    Science.gov (United States)

    Bihaqi, Syed Waseem; Sharma, Meenakshi; Singh, Avninder Pal; Tiwari, Manisha

    2009-07-30

    Convolvulus pluricaulis (Convolvulaceae) has long been used as traditional herbal medicine in India as nerve tonic. We investigated neuroprotective effects of aqueous extract from Convolvulus pluricaulis (CP) against aluminium chloride induced neurotoxicity in rat cerebral cortex. Daily administration of CP (150 mg/kg) for 3 months along with aluminium chloride (50 mg/kg) decreased the elevated enzymatic activity of acetylcholine esterase and also inhibited the decline in Na(+)/K(+)ATPase activity which resulted from aluminium intake. Beside, preventing accumulation of lipid and protein damage, changes in the levels of endogenous antioxidant enzymes associated with aluminium administration were also rectified. Oral administration of CP preserved the mRNA levels of muscarinic receptor 1 (M1 receptor), choline acetyl transferase (ChAT) and Nerve Growth Factor-Tyrosine kinase A receptor (NGF-TrkA). It also ameliorated the upregulated protein expression of cyclin dependent kinase5 (Cdk5) induced by aluminium. The potential of CPE to inhibit aluminium induced toxicity was compared with rivastigmine tartrate (1mg/kg), which was taken as standard. The potential of the extract to prevent aluminium-induced neurotoxicity was also reflected at the microscopic level, indicative of its neuroprotective effects. Convolvulus pluricaulis possesses neuroprotective potential, thus validating its use in alleviating toxic effects of aluminium.

  11. Potentiometric determination of the 'formal' hydrolysis ratio of aluminium species in aqueous solutions.

    Science.gov (United States)

    Fournier, Agathe C; Shafran, Kirill L; Perry, Carole C

    2008-01-21

    The 'formal' hydrolysis ratio (h = C(OH-)added/C(Al)total) of hydrolysed aluminium-ions is an important parameter required for the exhaustive and quantitative speciation-fractionation of aluminium in aqueous solutions. This paper describes a potentiometric method for determination of the formal hydrolysis ratio based on an automated alkaline titration procedure. The method uses the point of precipitation of aluminium hydroxide as a reference (h = 3.0) in order to calculate the initial formal hydrolysis ratio of hydrolysed aluminium-ion solutions. Several solutions of pure hydrolytic species including aluminium monomers (AlCl3), Al13 polynuclear cluster ([Al13O4(OH)24(H2O)12]7+), Al30 polynuclear cluster ([Al30O8(OH)56(H2O)26]18+) and a suspension of nanoparticulate aluminium hydroxide have been used as 'reference standards' to validate the proposed potentiometric method. Other important variables in the potentiometric determination of the hydrolysis ratio have also been optimised including the concentration of aluminium and the type and strength of alkali (Trizma-base, NH3, NaHCO3, Na2CO3 and KOH). The results of the potentiometric analysis have been cross-verified by quantitative 27Al solution nuclear magnetic resonance (27Al NMR) measurements. The 'formal' hydrolysis ratio of a commercial basic aluminium chloride has been measured as an example of a practical application of the developed technique.

  12. Mortality and cancer incidence in workers in two Australian prebake aluminium smelters

    NARCIS (Netherlands)

    Sim, M. R.; del Monaco, A.; Hoving, J. L.; MacFarlane, E.; McKenzie, D.; Benke, G.; de Klerk, N.; Fritschi, L.

    2009-01-01

    BACKGROUND: Exposures in the aluminium production industry have been declining and this study aimed to investigate cancer and mortality in two Australian prebake aluminium smelters. METHODS: The cohort included 4396 males who had worked in a prebake smelter for at least 3 months. They were matched

  13. Influence of Alkali Treatment on the Surface Area of Aluminium Dross

    Directory of Open Access Journals (Sweden)

    N. S. Ahmad Zauzi

    2016-01-01

    Full Text Available Aluminium dross is an industrial waste from aluminium refining industry and classified as toxic substances. However, the disposal of dross as a waste is a burden to aluminium manufacturer industries due to its negative effects to the ecosystem, surface, and ground water. Therefore the purpose of this study is to evaluate the influence of sodium hydroxide (NaOH on the surface area and pore size of aluminium dross. There were 3 stages in the treatment activities, which were leaching, precipitation, and calcination process. The optimum result from this study was the surface area of aluminium dross increases from 10.1 m2/g up to 80.0 m2/g at 40°C, 1% NaOH, and 15-minute reaction time. Thus, aluminium dross has a potential to be converted into other useful material such as catalyst and absorbent. The benefit of this research is that the hazardous industrial waste can be turned into wealth to be used in other applications such as in catalytic activities and absorber in waste water treatment. Further investigation on the physicochemical of aluminium dross with different acid or alkali should be conducted to get deeper understanding on the aluminium dross as a catalyst-type material.

  14. Insight into the cellular fate and toxicity of aluminium adjuvants used in clinically approved human vaccinations

    Science.gov (United States)

    Mold, Matthew; Shardlow, Emma; Exley, Christopher

    2016-08-01

    Aluminium adjuvants remain the most widely used and effective adjuvants in vaccination and immunotherapy. Herein, the particle size distribution (PSD) of aluminium oxyhydroxide and aluminium hydroxyphosphate adjuvants was elucidated in attempt to correlate these properties with the biological responses observed post vaccination. Heightened solubility and potentially the generation of Al3+ in the lysosomal environment were positively correlated with an increase in cell mortality in vitro, potentially generating a greater inflammatory response at the site of simulated injection. The cellular uptake of aluminium based adjuvants (ABAs) used in clinically approved vaccinations are compared to a commonly used experimental ABA, in an in vitro THP-1 cell model. Using lumogallion as a direct-fluorescent molecular probe for aluminium, complemented with transmission electron microscopy provides further insight into the morphology of internalised particulates, driven by the physicochemical variations of the ABAs investigated. We demonstrate that not all aluminium adjuvants are equal neither in terms of their physical properties nor their biological reactivity and potential toxicities both at the injection site and beyond. High loading of aluminium oxyhydroxide in the cytoplasm of THP-1 cells without immediate cytotoxicity might predispose this form of aluminium adjuvant to its subsequent transport throughout the body including access to the brain.

  15. Aluminium based adjuvants and their effects on mitochondria and lysosomes of phagocytosing cells.

    Science.gov (United States)

    Ohlsson, Lars; Exley, Christopher; Darabi, Anna; Sandén, Emma; Siesjö, Peter; Eriksson, Håkan

    2013-11-01

    Aluminium oxyhydroxide, Al(OH)3 is one of few compounds approved as an adjuvant in human vaccines. However, the mechanism behind its immune stimulating properties is still poorly understood. In vitro co-culture of an aluminium adjuvant and the human monocytic cell line THP-1 resulted in reduced cell proliferation. Inhibition occurred at concentrations of adjuvant several times lower than would be found at the injection site using a vaccine formulation containing an aluminium adjuvant. Based on evaluation of the mitochondrial membrane potential, THP-1 cells showed no mitochondrial rupture after co-culture with the aluminium adjuvant, instead an increase in mitochondrial activity was seen. The THP-1 cells are phagocytosing cells and after co-culture with the aluminium adjuvant the phagosomal pathway was obstructed. Primary or early phagosomes mature into phagolysosomes with an internal pH of 4.5 - 5 and carry a wide variety of hydrolysing enzymes. Co-culture with the aluminium adjuvant yielded a reduced level of acidic vesicles and cathepsin L activity, a proteolytic enzyme of the phagolysosomes, was almost completely inhibited. THP-1 cells are an appropriate in vitro model in order to investigate the mechanism behind the induction of a phagocytosing antigen presenting cell into an inflammatory cell by aluminium adjuvants. Much information will be gained by investigating the phagosomal pathway and what occurs inside the phagosomes and to elucidate the ultimate fate of phagocytosed aluminium particles. © 2013.

  16. A new ion-selective electrode based on aluminium tungstate for Fe ...

    Indian Academy of Sciences (India)

    An inorganic cation exchanger, aluminum tungstate (AT), has been synthesized by adding 0.1 M sodium tungstate gradually into 0.1 M aluminium nitrate at pH 1.2 with continuous stirring. The ion exchange capacity for Na+ ion and distribution coefficients of various metal ions was determined on the column of aluminium ...

  17. Dietary exposure to aluminium of urban residents from cities in South China.

    Science.gov (United States)

    Jiang, Qi; Wang, Jing; Li, Min; Liang, Xuxia; Dai, Guangwei; Hu, Zhikun; Wen, Jian; Huang, Qiong; Zhang, Yonghui

    2013-01-01

    A dietary survey was conducted over three consecutive days by using 24-hour dietary recall in the Pearl River Delta of South China to investigate the dietary consumption status. A total of 1702 food samples, 22 food groups, were collected, and aluminium concentrations of foods were determined by using ICP-MS. Weekly dietary exposure to aluminium of the average urban residents of South China was estimated to be 1.5 mg kg⁻¹ body weight, which amounted to 76% of the provisional tolerable weekly intake. Wheat-made products (53.5%) contributed most to the dietary exposure, followed by vegetables (12.2%). The high-level consumers' weekly exposure to aluminium was 11.1 mg kg⁻¹ body weight, which amounted to 407% of the provisional tolerable weekly intake. The results indicated that the general urban residents in South China might be safe from aluminium exposure, but the high-level consumers might be at some risk of aluminium exposure. The foods contributing to aluminium exposure were processed food with aluminium-containing food additives. It is necessary to take effective measures to control the overuse of aluminium-containing food additives.

  18. Aluminium hydro(oxide)–based (AO) adsorbent for defluoridation of ...

    African Journals Online (AJOL)

    In this study, the performance of different aluminium hydroxide.based adsorbents was compared in terms of fluoride adsorption capacity, potential for repetitive regeneration, surface acidity and surface site concentrations. The adsorbents were aluminium hydro(oxide) (AO), activated alumina (AA), and pseudoboehmite (PB).

  19. XPS and SIMS study of aluminium native oxide modifications induced by Q-switched Nd :YAG laser treatment

    CSIR Research Space (South Africa)

    Barnier, V

    2006-04-01

    Full Text Available During laser cleaning of aluminium in ambient atmosphere, modifications of the metal surface can be induced by transient thermal effects. This work aims to characterize the modification of the aluminium oxide layer on pure aluminium for a wide range...

  20. Aluminium in allergen-specific subcutaneous immunotherapy--a German perspective.

    Science.gov (United States)

    Kramer, Matthias F; Heath, Matthew D

    2014-07-16

    We are living in an "aluminium age" with increasing bioavailability of the metal for approximately 125 years, contributing significantly to the aluminium body burden of humans. Over the course of life, aluminium accumulates and is stored predominantly in the lungs, bones, liver, kidneys and brain. The toxicity of aluminium in humans is briefly summarised, highlighting links and possible causal relationships between a high aluminium body burden and a number of neurological disorders and disease states. Aluminium salts have been used as depot-adjuvants successfully in essential prophylactic vaccinations for almost 100 years, with a convincing positive benefit-risk assessment which remains unchanged. However, allergen-specific immunotherapy commonly consists of administering a long-course programme of subcutaneous injections using preparations of relevant allergens. Regulatory authorities currently set aluminium limits for vaccines per dose, rather than per treatment course. Unlike prophylactic vaccinations, numerous injections with higher proportions of aluminium-adjuvant per injection are applied in subcutaneous immunotherapy (SCIT) and will significantly contribute to a higher cumulative life dose of aluminium. While the human body may cope robustly with a daily aluminium overload from the environment, regulatory cumulative threshold values in immunotherapy need further addressing. Based on the current literature, predisposing an individual to an unusually high level of aluminium, such as through subcutaneous immunotherapy, has the potential to form focal accumulations in the body with the propensity to exert forms of toxicity. Particularly in relation to longer-term health effects, the safety of aluminium adjuvants in immunotherapy remains unchallenged by health authorities - evoking the need for more consideration, guidance, and transparency on what is known and not known about its safety in long-course therapy and what measures can be taken to prevent or

  1. ADC3 YANG DIBUAT DENGAN PELEBURAN ULANG ALUMINIUM BEKAS SEBAGAI BAHAN PROPELER KAPAL KAYU

    Directory of Open Access Journals (Sweden)

    Suyanto Suyanto

    2016-11-01

    Full Text Available Saat ini pembuatan propeler aluminium pada industri kecil banyak memanfaatkan bahan dasar aluminium bekas. Namun produk yang dihasilkan belum memenuhi spesifikasi standar material. Penelitian dilakukan dengan menggunakan bahan dasar aluminium siku bekas dan aluminium kampas bekas. Variasi penambahan TiB sebagai grain refiner dilakukan pada saat peleburan. Perhitungan dengan simulasi Excel dilakukan untuk memperkirakan komposisi hasil pengecoran yang sesuai. Pengecoran ulang menghasilkan produk dengan tingkat porositas 3,3 % sampai 5,9 %. Penggunaan cetakan pasir ikut berperan dalam timbulnya porositas. Penambahan TiB sebanyak 0,5% ke ADC3 berpengaruh pada penurunan ukuran butir hingga 50%, peningkatan kekerasan hingga 23%, peningkatan kekuatan tarik hingga 11%, serta penurunan keuletan hingga 20%. Kata kunci: ADC3, pengecoran ulang aluminium, propeler.

  2. Development of EL element by ion implanting into aluminium film

    Energy Technology Data Exchange (ETDEWEB)

    Maeno, Tomokazu; Tanizaki, Yoshiyuki [Tokyo Metropolitan Industrial Technology Research Inst. (Japan); Morisaki; Shigeki

    1999-01-01

    Rare earth elements were added to a barrier type anodized aluminium film by an ion implantation method, and then the film was reoxidized with direct current. EL characteristic properties by adding elements were observed by reoxidation. Red, blue and green were shown by adding Eu, Tm and Tb, respectively. The EL characteristics of barrier type film were affected by the surface pretreatment. The film treated with degreasing showed that the EL intensity increased much more from lower reanodizing voltage than that of film treated with electropolishing. The film with some elements showed each peculiar color without interference. So that we can see the mixed colors of them. (S.Y.)

  3. Characterisation of austempered spheroidal graphite aluminium cast iron

    Energy Technology Data Exchange (ETDEWEB)

    Boutorabi, S.M.A. [Iran Univ. of Science and Technology, Tehran (Iran, Islamic Republic of). Dept. of Metallurgy and Materials

    1997-06-01

    The micro constituents of austempered spheroidal graphite aluminium cast iron were investigated. The heat tinting, special etching and microhardness measurement techniques were used. The results showed that the colour of each micro constituents and the hardness values in austempered ductile iron depend on the carbon content of each phase. The above techniques were supported by using an special etching which showed similar differences in each phase. It was shown that the heat tinting and special etching are reliable tools to characterise the complex matrix of ADI. The microhardness data supported interestingly the colour changes in above technique. (orig.)

  4. High Temperature Strength of Oxide Dispersion Strengthened Aluminium

    DEFF Research Database (Denmark)

    Clauer, A.H.; Hansen, Niels

    1984-01-01

    The tensile flow stress of coarse-grained dispersion strengthened Al-Al2O3 materials were measured as a function of temperature (77–873 K) and volume fraction (0.19-0.92 vol.%) of aluminium oxide. For the same material, the creep strength was determined as a function of temperature in the range 573...... is proportional to the Orowan stress and it does not fall below about 0.5-0.7 of the Orowan stress. During creep even at stresses near the threshold stress a dislocation substructure develops consisting of dense tangles surrounding the larger particles and the particle clusters in addition to a coarse dislocation...

  5. SYNTHESIS OF ALUMINIUM BORATE WHISKERS THROUGH WET MOLTEN SALT METHOD

    Directory of Open Access Journals (Sweden)

    Xue Zhang

    2017-12-01

    Full Text Available Aluminium borate (Al₄B₂O₉ whiskers were successfully synthesized by the wet molten salt method at 800 oC through control the aluminum/boron atomic ratio and synthesis temperature. The as-received Al₄B₂O₉ whiskers were characterized by scanning electron microscopy (SEM, X-ray diffraction (XRD and thermal analysis. A solution-liquid-solid (SLS mechanism was proposed for the growth mechanism of the whiskers on the basis of the experimental phenomena and the TG-DSC data of the mixed raw materials.

  6. Role of acidic chemistries in steam treatment of aluminium alloys

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    2015-01-01

    The effect of acidic chemistry on the accelerated growth of oxide on aluminium alloys Peraluman 706TM and AA6060 under exposure to high temperature steam was investigated. Studied chemistries were based on citrates and phosphates. Results showed that the presence of citrate and phosphate anions...... initiate doxide growth at the intermetallic particles while growth and corrosion performance of oxide was found tobe a function of anions type and their concentration. Further, steam treatment with phosphates exhibited better performance under acetic acid salt spray and filiform corrosion test whereas...

  7. Fatigue behaviour of 6061 aluminium alloy and its composite

    OpenAIRE

    Hwa, Ping

    2001-01-01

    Fatigue behaviour of an artificial aged powder metallurgy 6061 aluminium alloy, and a composite made of this alloy with 15% volume fraction of SiCp was investigated. The alloy was subjected to T6 heat treatment, as was the composite material chosen (which incorporated SiC particles of average size 30pm). An extensive experimental programme was carried out in which fatigue lives were determined using load-controlled axial loading of unnotched cylindrical samples, at stress ratios of-1 and 0.1....

  8. Study of the cooling process of an extruded aluminium profile

    International Nuclear Information System (INIS)

    Bouffioux, C.; Habraken, A.M.; Carton, M.; Lecomte-Beckers, J.

    2004-01-01

    The prediction of the final axial stresses and the residual strains of complex extruded aluminium profiles requires a good knowledge of the material behavior and of the industrial process. This paper is focused on the methods required to provide the whole set of data: material ones and process ones. Scanning differential calorimetry, dilatometry and diffusivity tests identify thermophysic material properties and hot tensile tests identify parameters of the elasto-visco-plastic Norton-Hoff law. The description of the industrial process and its simulations are described. Then a sensitivity analyzis provides the cooling key parameters causing the undesired final curvature during the industrial process

  9. Deviatoric Response of AN Armour-Grade Aluminium Alloy

    Science.gov (United States)

    Appleby-Thomas, G. J.; Hazell, P. J.; Millett, J.; Bourne, N. K.

    2009-12-01

    Aluminium alloys such as 5083 H32 are established light-weight armour materials. As such, the shock response of these materials is of great importance. The shear strength of a material under shock loading provides an insight into its ballistic performance. In this investigation embedded manganin stress gauges have been employed to measure both the longitudinal and lateral components of stress during plate-impact experiments over a range of impact stresses. In turn, these results were used to determine the shear strength and to investigate the time dependence of lateral stress behind the shock front to give an indication of material response.

  10. Plasmonic Colour Filters Based on Coaxial Holes in Aluminium.

    Science.gov (United States)

    Rajasekharan Unnithan, Ranjith; Sun, Miao; He, Xin; Balaur, Eugeniu; Minovich, Alexander; Neshev, Dragomir N; Skafidas, Efstratios; Roberts, Ann

    2017-04-04

    Aluminum is an alternative plasmonic material in the visible regions of the spectrum due to its attractive properties such as low cost, high natural abundance, ease of processing, and complementary metal-oxide-semiconductor (CMOS) and liquid crystal display (LCD) compatibility. Here, we present plasmonic colour filters based on coaxial holes in aluminium that operate in the visible range. Using both computational and experimental methods, fine-tuning of resonance peaks through precise geometric control of the coaxial holes is demonstrated. These results will lay the basis for the development of filters in high-resolution liquid crystal displays, RGB-spatial light modulators, liquid crystal over silicon devices and novel displays.

  11. The effect of atmospheric corona treatment on AA1050 aluminium

    DEFF Research Database (Denmark)

    Jariyaboon, Manthana; Møller, Per; Dunin-Borkowski, Rafal E.

    2010-01-01

    The effect of atmospheric corona discharge on AM 050 aluminium surface was investigated using electrochemical polarization, SEM-EDX, FIB-SEM. and XPS. The corona treatment was performed with varying time (1, 5, and 15 min) in atmospheric air. A 200 nm oxide layer was generated on AA1050 after...... the 15 min air corona treatment. A significant reduction in anodic and cathodic reactivities was observed starting from 1 min exposure, which further decreased with prolonged exposure (15 min) and after delayed testing (after 30 days). The reduction in surface reactivity is due to the formation...

  12. The fracture of boron fibre-reinforced 6061 aluminium alloy

    Science.gov (United States)

    Wright, M. A.; Welch, D.; Jollay, J.

    1979-01-01

    The fracture of 6061 aluminium alloy reinforced with unidirectional and cross-plied 0/90 deg, 0/90/+ or - 45 deg boron fibres has been investigated. The results have been described in terms of a critical stress intensity, K(Q). Critical stress intensity factors were obtained by substituting the failure stress and the initial crack length into the appropriate expression for K(Q). Values were obtained that depended on the dimensions of the specimens. It was therefore concluded that, for the size of specimen tested, the values of K(Q) did not reflect any basic materials property.

  13. Persistent Skin Reactions and Aluminium Hypersensitivity Induced by Childhood Vaccines

    DEFF Research Database (Denmark)

    Salik, Elaha; Løvik, Ida; Andersen, Klaus E

    2016-01-01

    There is increasing awareness of reactions to vaccination that include persistent skin reactions. We present here a retrospective investigation of long-lasting skin reactions and aluminium hypersensitivity in children, based on medical records and questionnaires sent to the parents. In the 10-year...... treated with potent topical corticosteroids and disappeared slowly. Although we advised families to continue vaccination of their children, one-third of parents omitted or postponed further vaccinations....... period 2003 to 2013 we identified 47 children with persistent skin reactions caused by childhood vaccinations. Most patients had a typical presentation of persisting pruritic subcutaneous nodules. Five children had a complex diagnostic process involving paediatricians, orthopaedics and plastic surgeons...

  14. Method of preparing an Al-Ti-B grain refiner for aluminium-comprising products, and a method of casting aluminium products

    OpenAIRE

    Brinkman, H.J.; Duszczyk, J.; Katgerman, L.

    1999-01-01

    The invention relates to a method of preparing an Al-Ti-B grain refiner for cast aluminium-comprising products. According to the invention the preparation is realized by mixing powders selected from the group comprising aluminium, titanium, boron, and alloys and intermetallic compounds thereof, compressing, heating in an inert environment until an exothermic reaction is initiated and cooling. It has been shown that when the grain refiner thus prepared is applied, the quality of cast products ...

  15. KS R41B. A high performance steel-aluminium composite material; KS R41B. Ein Stahl-Aluminium-Verbundwerkstoff fuer hohe Belastungen

    Energy Technology Data Exchange (ETDEWEB)

    Deicke, K. [KS Gleitlager GmbH (Germany). Bereich Metall; Matucha, H.; Schubert, W. [KS Gleitlager GmbH, St. Leon-Rot (Germany); Steffens, T. [KS Gleitlager GmbH, Neckarsulm (Germany)

    2002-08-01

    Aluminium-tin alloys have been well-known for a long time and have proved to be suitable bearing materials for crankshaft bearings for many years. The known alloy AlZn4,5SiCuPb is one of the aluminium materials capable of sustaining the highest mechanical loads. In order to achieve optimum sliding properties, it would be necessary to increase the share of the soft lead phase in the alloy. This article by KS Gleitlager GmbH shows a reasonably priced manufacturing technology for high-performance aluminium-zinc-silicon-copper alloys. (orig.) [German] Die Aluminium-Zinn-Lagerlegierungen sind seit langem bekannt und haben sich seit Jahren als Lagerwerkstoff fuer Kurbelwellenlager bewaehrt. Die Legierung AlZn4,5SiCuPb gehoert zu den mechanisch am hoechsten belastbaren Aluminium-Werkstoffen. Um optimale Gleiteigenschaften zu erzielen, muesste in der Legierung der Anteil des weichen Bleis noch weiter erhoeht werden. Dieser Beitrag der KS Gleitlager GmbH zeigt eine kostenguenstige Herstelltechnologie fuer hochbelastbare Aluminium-Zink-Silizium-Kupfer-Legierungen. (orig.)

  16. Friction stir spot welding of dissimilar aluminium alloys

    International Nuclear Information System (INIS)

    Bozkurt, Yahya

    2016-01-01

    Friction stir spot welding (FSSW) has been proposed as an effective technology to spot weld the so-called “difficult to be welded” metal alloys such as thin sheets aluminum alloys and dissimilar materials. FSSW is derived from friction stir welding technology, its principle benefit being low cost joining, lower welding temperature and shorter welding time than conventional welding methods. In this study, dissimilar AlMg 3 and AlCu 4 Mg 1 aluminium alloy plates were FSSWed by offsetting the low strength sheet on upper side of the weld. The effects of tool rotation speed on the microstructure, lap shear fracture load (LSFL), microhardness and fracture features of the weld are investigated by constant welding parameters. The maximum LSFL was obtained by increasing the tool rotational speed. However, the joints exhibited pull-out nugget fracture mode under lap shear tensile testing conditions. The largest completely bonded zone was observed as 5.86 mm which was narrower at the opposite position of the joint. Key words: friction stir spot welding, aluminium alloys, mechanical properties, dissimilar joint, welding parameters

  17. Crystallographic orientation-spray formed hypereutectic aluminium-silicon alloys

    Directory of Open Access Journals (Sweden)

    Hamilta de Oliveira Santos

    2005-06-01

    Full Text Available Aluminium-silicon alloys have been wide accepted in the automotive, electric and aerospace industries. Preferred orientation is a very common condition for metals and alloys. Particularly, aluminium induces texture during the forming process. The preparation of an aggregate with completely random crystal orientation is a difficult task. The present work was undertaken to analyse the texture by X-ray diffraction techniques, of three spray formed hypereutectic Al-Si alloys. Samples were taken from a billet of an experimental alloy (alloy 1 and were subsequently hot-rolled and cold-rolled (height reduction, 72% and 70%, respectively. The other used samples, alloys 2 and 3, were taken from cylinders liners. The results from the Laue camera showed texture just in the axial direction of alloy 3. The pole figures also indicated the presence of a typical low intensity deformation texture, especially for alloy 3. The spray formed microstructure, which is very fine, hinders the Al-Si texture formation during mechanical work.

  18. Fatigue in a heat treatable high silicon containing aluminium alloy

    Science.gov (United States)

    González, J. A.; Talamantes-Silva, J.; Valtierra, S.; Colás, Rafael

    2017-05-01

    The use of cast aluminium alloys in automobiles contributes to reductions in weight and fuel consumption without impairing the safety for the occupants or the performance of the car. Most of the alloys used are heat treatable hypoeutectic Al-Si alloys, which have the drawback of exhibiting low wear resistance. So industry relies in wear resistant alloys, such as grey iron, for the liners of the combustion chambers in engine blocks, which increase the weight of the engine. Therefore, it is of interest to cast high silicon containing alloys into engine components that are able to resist wear while maintaining the mechanical properties required by the components. This work presents the result of the work carried out in a high silicon containing heat treatable aluminium alloy as it is subjected to high cycle fatigue. The alloy was prepared and cast in ingots designed to promote one dimensional solidification gradient to obtain samples to study the high cycle fatigue. The material was machined into hour-glass specimens that were tested at room temperature in a servohydraulic machine under load control following the stair case method. The results show that the resistance to fatigue depends on the microstructure of the sample, as the fatigue cracks originate in pores close to the surface of the sample and propagate through the eutectic aggregate. The results from this work are compared with those from previously obtained with hypoeutectic alloys.

  19. Aluminium chloride-induced toxicity in zebrafish larvae.

    Science.gov (United States)

    Monaco, A; Grimaldi, M C; Ferrandino, I

    2017-05-01

    Embryos at shield stage and larvae at protruding mouth stage were exposed to different concentrations of aluminium chloride (AlCl 3 ) for 72 h with the purpose to analyse their phenotype and lethality. After 24, 48 and 72 h of treatment, higher toxicity of the metal was observed on larvae with minimal lethal concentration of 0.25, 0.20 and 0.08 mm, respectively, while for embryos the corresponding values were 40, 25 and 16 mm. We observed pericardial oedema and alteration of heart rate in 50% of larvae after 48 h of exposure to 100 μm. In larvae exposed to the same concentration, there was also a neurological injury at the level of glial cells, with the number of glial fibrillary acidic protein-positive cells being significantly reduced. This study confirms the toxic nature of this metal and shows that aluminium could also interestingly represent a cardiotoxin in addition to its neurotoxic ability. © 2016 John Wiley & Sons Ltd.

  20. Formability of aluminium sheets manufactured by solid state recycling

    Science.gov (United States)

    Kore, A. S.; Nayak, K. C.; Date, P. P.

    2017-09-01

    Conventional recycling practices for non-ferrous metallic scrap involves melting followed by purification. This practice is suitable for recycling when the large volume of scrap is available. Though such recycling reduces consumption of diminishing metallic resources, high energy requirement and material loss during melting and purification limit its applicability. In the present work, manufacturing of solid state recycled aluminium sheet by hot rolling is explored and its formability characterized. Aluminium chips were divided into smaller particles (1~2mm) by crushing. After stress relief annealing, chips were cold compacted into square slabs (75*75mm section) of different thicknesses. Another similar set of slabs was made by hot compaction. The compacted slabs were hot rolled over a number of passes at 400°C. Each slab was reduced to approximately 90% thickness to get the sheet thickness in the range of 0.6 to 1.5 mm. Microstructure revealed good interface bonding between the chip particles. Mechanical properties of the sheet from room temperature up to 200°C and at different strain rates were characterized by a number of tensile tests. Circular blanks from sheet were drawn into cylindrical cups and strain distribution was observed along different directions of rolling using circle grid analysis.

  1. A 3D printed superconducting aluminium microwave cavity

    International Nuclear Information System (INIS)

    Creedon, Daniel L.; Goryachev, Maxim; Kostylev, Nikita; Tobar, Michael E.; Sercombe, Timothy B.

    2016-01-01

    3D printing of plastics, ceramics, and metals has existed for several decades and has revolutionized many areas of manufacturing and science. Printing of metals, in particular, has found a number of applications in fields as diverse as customized medical implants, jet engine bearings, and rapid prototyping in the automotive industry. Although many techniques are used for 3D printing metals, they commonly rely on computer controlled melting or sintering of a metal alloy powder using a laser or electron beam. The mechanical properties of parts produced in such a way have been well studied, but little attention has been paid to their electrical properties. Here we show that a microwave cavity (resonant frequencies 9.9 and 11.2 GHz) 3D printed using an Al-12Si alloy exhibits superconductivity when cooled below the critical temperature of aluminium (1.2 K), with a performance comparable with the common 6061 alloy of aluminium. Superconducting cavities find application in numerous areas of physics, from particle accelerators to cavity quantum electrodynamics experiments. The result is achieved even with a very large concentration of non-superconducting silicon in the alloy of 12.18%, compared with Al-6061, which has between 0.4% and 0.8%. Our results may pave the way for the possibility of 3D printing superconducting cavity configurations that are otherwise impossible to machine.

  2. Cancellous bone homograft storage with aluminium-polyethylene bags.

    Science.gov (United States)

    Meana, A; Martinez, R; Cañal, P; Arriaga, M J; Román, F San; Llames, S; Orós, C; Moreno, A; Fernandez, C

    2006-01-01

    In order to transport and cryopreserve human tissues, it is essential to have an easy-to-use recipient where tissues can be kept in sterile conditions. Here we show the results obtained by using Macopharma's tissue freezing bags, an aluminium-polyethylene multilayer bag, in our tissue bank of the Centro Comunitario de Sangre y Tejidos de Asturias. Five hundred and twenty-seven cancellous bone homografts were obtained from hospitals located 120 km around our Bank. The homografts were submitted to bacteriological controls and sent to our bank in these bags. They were stored at -70 degrees C and sent in dry ice to about 50 hospitals, where the tissue was bacteriologically controlled and grafted. Furthermore, the behaviour of these bags at -140 degrees C (vapour nitrogen) or -196 degrees C (liquid nitrogen) was tested. Our results indicate that Macopharma aluminium-polyethylene bags are suitable for the transporting and cryopreserving of cancellous bone homografts. These bags could also be used for keeping tissues in nitrogen containers.

  3. Geopolymerisation of fly ashes with waste aluminium anodising etching solutions.

    Science.gov (United States)

    Ogundiran, M B; Nugteren, H W; Witkamp, G J

    2016-10-01

    Combined management of coal combustion fly ash and waste aluminium anodising etching solutions using geopolymerisation presents economic and environmental benefits. The possibility of using waste aluminium anodising etching solution (AES) as activator to produce fly ash geopolymers in place of the commonly used silicate solutions was explored in this study. Geopolymerisation capacities of five European fly ashes with AES and the leaching of elements from their corresponding geopolymers were studied. Conventional commercial potassium silicate activator-based geopolymers were used as a reference. The geopolymers produced were subjected to physical, mechanical and leaching tests. The leaching of elements was tested on 28 days cured and crushed geopolymers using NEN 12457-4, NEN 7375, SPLP and TCLP leaching tests. After 28 days ambient curing, the geopolymers based on the etching solution activator showed compressive strength values between 51 and 84 MPa, whereas the commercial potassium silicate based geopolymers gave compressive strength values between 89 and 115 MPa. Based on the regulatory limits currently associated with the used leaching tests, all except one of the produced geopolymers (with above threshold leaching of As and Se) passed the recommended limits. The AES-geopolymer geopolymers demonstrated excellent compressive strength, although less than geopolymers made from commercial activator. Additionally, they demonstrated low element leaching potentials and therefore can be suitable for use in construction works. Copyright © 2016. Published by Elsevier Ltd.

  4. Consolidation of copper and aluminium powders by spark plasma sintering

    Science.gov (United States)

    Saiprasad, M.; Atchayakumar, R.; Thiruppathi, K.; Raghuraman, S.

    2016-09-01

    Processing in the powder metallurgy route has emerged as an economical process for the production of near net shaped components with a wide range of desired mechanical properties suitable for various applications of industrial needs. This research work was conducted with an objective of studying the improvisation of density and hardness of Copper-Aluminium alloy prepared by spark plasma sintering. Cu-Al alloy with a composition of 95% copper and 5% aluminium was prepared by SPS process. SPS is a low voltage, DC pulse current activated, pressure-assisted sintering, which enables sintering at lower temperatures and shorter durations. The combination offered by Cu-Al alloy of high strength and high corrosion resistance results their applications under a wide variety of conditions. The density and hardness of the prepared sample were measured by conducting appropriate tests. Apparently, the values of hardness and density of the specimen prepared by SPS seemed to be better than that of conventional sintering. The experimental procedure, testing methodologies and analysis are presented.

  5. Investigation on wear and corrosion behavior of equal channel angular pressed aluminium 2014 alloy

    Science.gov (United States)

    Divya, S. P.; Yoganandan, G.; Balaraju, J. N.; Srinivasan, S. A.; Nagaraj, M.; Ravisankar, B.

    2018-02-01

    Aluminium 2014 alloy solutionized at 495°C, aged at 195°C was subjected to Equal Channel Angular Pressing (ECAP). Dry sliding wear tests were conducted using pin on disc tribometer system under nominal loads of 10N and 30N with constant speed 2m/s for 2000m in order to investigate their wear behavior after ECAP. The Co-efficient of friction and loss in volume were decreased after ECAP. The dominant wear mechanism observed was adhesion, delamination in addition to these wear mechanisms, oxidation and transfer of Fe from the counter surface to the Al 2014 pin were observed at higher loading condition. The corrosion behavior was evaluated by potentiodynamic polarization (PDP) and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. The results obtained from PDP showed higher corrosion potential and lower corrosion density after ECAP than base. Electrochemical impedance spectroscopy (EIS) showed higher charge transfer resistance after ECAP. Surface morphology showed decreased pit size and increased oxygen content in ECAP sample than base after PDP.

  6. An efficient method of spot welding Aluminium alloys with induction preheating

    Directory of Open Access Journals (Sweden)

    Jawad Saleem

    2016-12-01

    Full Text Available Steel has been the material of choice for automobile manufacturers. In the recent years material such as aluminium and its alloys are taking over the market because of their light weight. The use of aluminium, in automobile manufacturing can result in overall fuel efficiency. Spot welding aluminium alloys require higher electric power and less welding time as compared to steel. Welding guns that can produce an electric current which is approximately 2 to 3 times higher, as compared to steel are required for spot welding aluminium. An efficient method of spot welding Aluminium alloys with the preheating process has been proposed in this paper. Preheating Aluminium sheet before spot welding reduces the thermal and electrical resistance which brings down the electric current requirement to spot weld Aluminium structures. Both spot welding and induction preheating process have been modelled in this paper. The test results of the preheating process have also been verified with practical heating trials. The preheating is performed on-the-fly in advance to spot welding process. The results show that spot welding Al 6082 after preheating up to 200 oC, the output current requirements to make the spot weld are reduced by 22%.

  7. Factors affecting the aluminium content of human femoral head and neck.

    Science.gov (United States)

    Zioła-Frankowska, Anetta; Dąbrowski, Mikołaj; Kubaszewski, Łukasz; Rogala, Piotr; Frankowski, Marcin

    2015-11-01

    Tissues for the study were obtained intraoperatively during hip replacement procedures from 96 patients. In all the cases, the indication for this treatment was primary or secondary degenerative changes in the hip joint. The subject of the study was the head and neck of the femur, resected in situ. Aluminium concentrations measured in femoral head and neck samples from patients aged between 25 and 91 were varied. Statistical methods were applied to determine the variations in relation to the parameters from the background survey. Significant differences in the aluminium content of femoral head samples were observed between patients under and over 60 years of age. Based on the results, it was confirmed that the aluminium accumulates in bones over a lifetime. The study showed that the content of aluminium in the head and neck of the femur depends on the factors such as: type of medicines taken, contact with chemicals at work, differences in body anatomy and sex. The study on the levels of aluminium in bones and the factors affecting its concentration is a valuable source of information for further research on the role of aluminium in bone diseases. Based on the investigations, it was found that the GF-AAS technique is the best analytical tool for routine analysis of aluminium in complex matrix samples. The use of femoral heads in the investigations was approved by the Bioethics Committee of the University of Medical Sciences in Poznań (Poland). Copyright © 2015 Elsevier Inc. All rights reserved.

  8. Dietary exposure to aluminium in the popular Chinese fried bread youtiao.

    Science.gov (United States)

    Li, Ge; Zhao, Xue; Wu, Shimin; Hua, Hongying; Wang, Qiang; Zhang, Zhiheng

    2017-06-01

    Youtiao is a typical, traditional and widely consumed fried food in China. Fermentation of youtiao involves the use of aluminium potassium sulphate (alum). There are health concerns related to the levels of aluminium in food; therefore, we aimed to determine the aluminium concentrations of youtiao from various locations, and to estimate the dietary exposure by different age groups in southern and northern China. The aluminium content of youtiao samples varied considerably (range = 4.46-852.69 mg kg -1 ). Both the mean and median aluminium contents of youtiao exceeded 100 mg kg -1 , which is the China National Standard (GB) 2760-2014 National Food Safety for Standards for food additives. However, the median and 97.5th percentile of weekly dietary exposure to aluminium from youtiao, estimated using Monte Carlo simulation, did not exceed the provisional tolerable weekly intake (PTWI) set by the joint FAO/WHO Expert Committee on Food Additives (JECFA) for children, adolescents, adults and seniors. The weekly dietary exposure to aluminium would exceed the PTWI if children, adolescents, adults and seniors consumed 134.47, 260.98, 327.10 or 320.41 g of youtiao per week, respectively.

  9. Minimal inhibitory concentration of natural vinegar and of aluminium acetate-tartrate solution.

    Science.gov (United States)

    Lang, Ursula

    2013-07-01

    Vinegar and aluminium acetate preparations are used for treatment of ear infections. It is instrumental to know the minimal inhibitory concentration to get effective remedies. This study was performed to assess the lowest dilution of vinegar (specified content, 6% acetic acid) and aluminium acetate-tartrate solution (specified content, 1.4% aluminium and 6% acetic acid) to determine the minimum inhibitory concentration against bacteria commonly found in chronic ear infections. Laboratory study on 2 samples of aluminium acetate-tartrate and on 1 sample of natural white wine vinegar on antibacterial effects against Staphylococcus aureus, Staphylococcus epidermidis, Proteus vulgaris, Pseudomonas aeruginosa, and Escherichia coli. Performing of a susceptibility testing-determination of the minimum inhibitory concentration (MIC) with the method of microbouillon dilution (DIN 58940 part 7). Acetic acid was found to be effective in vitro in concentrations of 0.1% to 0.2% against the tested bacteria; aluminium acetate-tartrate solution was found to be effective in vitro in concentrations of 1.25% to 2.5% against the tested bacteria. Vinegar respectively acetic acid diluted with water and aqueous aluminium acetate-tartrate solution could be effective ototopic preparations caused by one of the tested bacteria. For its effectiveness, an acid pH not higher than 4.5 is essential. Experiments with aluminium acetate-tartrate preparations on animals and clinical trials are required to obtain information about the response rates in ear infections and about any adverse effects.

  10. An investigation on compression strength analysis of commercial aluminium tube to aluminium 2025 tube plate by using TIG welding process

    Energy Technology Data Exchange (ETDEWEB)

    Kannan, S., E-mail: kannan.dgl201127@gmail.com [Department of Mechanical Engineering and Mining Machinery Engineering, Indian Institute of Technology (ISM), Dhanbad, Jharkhand, India, 826004 (India); Senthil Kumaran, S., E-mail: sskumaran@ymail.com [Research and Development Center, Department of Mechanical Engineering, RVS Educational Trust' s Group of Institutions, RVS School of Engineering and Technology, Dindigul, Tamilnadu, India, 624005 (India); Kumaraswamidhas, L.A., E-mail: lakdhas1978@gmail.com [Department of Mechanical Engineering and Mining Machinery Engineering, Indian School of Mines University, Dhanbad, Jharkhand, India, 826004 (India)

    2016-05-05

    In this present study, Tungsten inert gas (TIG) welding was applied to weld the dissimilar materials and authenticate the mechanical and metallurgical properties of tube to tube plate made up of commercial aluminium and Al 2025 respectively using an Zirconiated tungsten electrode along with filler material aluminium ER 2219. In total, twenty five pieces has been subjected to compression strength and hardness value to evaluate the optimal joint strength. The three optimization technique has been used in this experiment. Taguchi L{sub 25} orthogonal array is used to identify the most influencing process parameter which affects the joint strength. ANOVA method is measured for both compression strength and hardness to calculate the percentage of contribution for each process parameter. Genetic algorithm is used to validate the results obtained from the both experimental value and optimization value. The micro structural study is depicted the welding joints characterization in between tube to tube plate joints. The radiograph test is conducted to prove the welds are non-defective and no flaws are found during the welding process. The mechanical property of compression strength and hardness has been measured to obtain the optimal joint strength of the welded sample was about 174.846 MPa and 131.364 Hv respectively. - Highlights: • Commercial Al tube and Al 2025 tube plate successfully welded by TIG welding. • Compression strength and hardness value proves to obtain optimal joint strength. • The maximum compression and hardness was achieved in various input parameters.

  11. An investigation on compression strength analysis of commercial aluminium tube to aluminium 2025 tube plate by using TIG welding process

    International Nuclear Information System (INIS)

    Kannan, S.; Senthil Kumaran, S.; Kumaraswamidhas, L.A.

    2016-01-01

    In this present study, Tungsten inert gas (TIG) welding was applied to weld the dissimilar materials and authenticate the mechanical and metallurgical properties of tube to tube plate made up of commercial aluminium and Al 2025 respectively using an Zirconiated tungsten electrode along with filler material aluminium ER 2219. In total, twenty five pieces has been subjected to compression strength and hardness value to evaluate the optimal joint strength. The three optimization technique has been used in this experiment. Taguchi L 25 orthogonal array is used to identify the most influencing process parameter which affects the joint strength. ANOVA method is measured for both compression strength and hardness to calculate the percentage of contribution for each process parameter. Genetic algorithm is used to validate the results obtained from the both experimental value and optimization value. The micro structural study is depicted the welding joints characterization in between tube to tube plate joints. The radiograph test is conducted to prove the welds are non-defective and no flaws are found during the welding process. The mechanical property of compression strength and hardness has been measured to obtain the optimal joint strength of the welded sample was about 174.846 MPa and 131.364 Hv respectively. - Highlights: • Commercial Al tube and Al 2025 tube plate successfully welded by TIG welding. • Compression strength and hardness value proves to obtain optimal joint strength. • The maximum compression and hardness was achieved in various input parameters.

  12. ANALISIS KRITIKALITAS BAHAN BAKAR NUKLIR BEKAS REAKTOR RSG-GAS PADA RAK BERBAHAN ALUMINIUM

    Directory of Open Access Journals (Sweden)

    Pungky Ayu Artiani

    2017-08-01

    Full Text Available Penggunaan stainless steel sebagai material rak penyimpanan bahan bakar nuklir bekas (BBNB di fasilitas Kanal Hubung – Instalasi Penyimpanan Sementara Bahan Bakar Bekas (KH-IPSB3 berpotensi menyebabkan terjadinya korosi galvanik pada BBNB sehingga penggantian material rak penyimpanan BBNB perlu dipertimbangkan. Potensi korosi galvanik terjadi karena aluminium sebagai material utama kelongsong Bahan Bakar Nuklir (BBN Reaktor Serba Guna - G. A. Siwabessy (reaktor RSG-GAS berinteraksi dengan stainless steel sebagai material rak penyimpan BBNB. Aluminium dapat digunakan sebagai material alternatif rak penyimpanan BBNB untuk mengurangi efek korosi galvanik. Penelitian ini bertujuan untuk mengkaji kritikalitas rak penyimpanan BBNB dengan material aluminium. Jaminan kritikalitas diperlukan untuk menjaga keselamatan fasilitas KH-IPSB3. Rak penyimpanan aluminium yang optimum dikaji dengan melakukan simulasi ukuran pitch dan menghitung laju serapan neutron pada kondisi normal (tidak terjadi kecelakaan. Perhitungan nilai kritikalitas (keff dilakukan menggunakan program Monte Carlo N-Particle versi 6 (MCNP6. Model yang digunakan adalah model 3-dimensi satu rak utuh yang terisi penuh dengan BBNB di dalam kolam penyimpanan. Hasil perhitungan pada ukuran pitch 127 mm menunjukkan bahwa nilai keff rak penyimpanan BBNB dengan material aluminium (keff = 0,7709 lebih besar 13,20% dibandingkan material stainless steel (keff = 0,6810. Nilai keff rak penyimpanan BBNB dengan material aluminium pada ukuran tersebut masih berada dalam rentang yang disyaratkan yaitu keff kurang dari 0,95. Nilai keff dipengaruhi oleh ukuran pitch, dimana dengan berkurangnya ukuran pitch 1 mm dapat meningkatkan nilai keff sebesar 14,24%. Nilai laju serapan neutron juga mempengaruhi nilai keff, di mana laju serap neutron rak penyimpanan dengan material aluminium lebih kecil dibandingkan material stainless steel. Hasil simulasi menunjukkan bahwa rak penyimpanan dengan material aluminium

  13. Chemical mimicking of bio-assisted aluminium extraction by Aspergillus niger's exometabolites.

    Science.gov (United States)

    Boriová, Katarína; Urík, Martin; Bujdoš, Marek; Pifková, Ivana; Matúš, Peter

    2016-11-01

    Presence of microorganisms in soils strongly affects mobility of metals. This fact is often excluded when mobile metal fraction in soil is studied using extraction procedures. Thus, the first objective of this paper was to evaluate strain Aspergillus niger's exometabolites contribution on aluminium mobilization. Fungal exudates collected in various time intervals during cultivation were analyzed and used for two-step bio-assisted extraction of alumina and gibbsite. Oxalic, citric and gluconic acids were identified in collected culture media with concentrations up to 68.4, 2.0 and 16.5 mmol L -1 , respectively. These exometabolites proved to be the most efficient agents in mobile aluminium fraction extraction with aluminium extraction efficiency reaching almost 2.2%. However, fungal cultivation is time demanding process. Therefore, the second objective was to simplify acquisition of equally efficient extracting agent by chemically mimicking composition of main organic acid components of fungal exudates. This was successfully achieved with organic acids mixture prepared according to medium composition collected on the 12th day of Aspergillus niger cultivation. This mixture extracted similar amounts of aluminium from alumina compared to culture medium. The aluminium extraction efficiency from gibbsite by organic acids mixture was lesser than 0.09% which is most likely because of more rigid mineral structure of gibbsite compared to alumina. The prepared organic acid mixture was then successfully applied for aluminium extraction from soil samples and compared to standard single step extraction techniques. This showed there is at least 2.9 times higher content of mobile aluminium fraction in soils than it was previously considered, if contribution of microbial metabolites is considered in extraction procedures. Thus, our contribution highlights the significance of fungal metabolites in aluminium extraction from environmental samples, but it also simplifies the

  14. Aluminium exposure from parenteral nutrition in preterm infants and later health outcomes during childhood and adolescence.

    Science.gov (United States)

    Fewtrell, Mary S; Edmonds, Caroline J; Isaacs, Elizabeth; Bishop, Nick J; Lucas, Alan

    2011-08-01

    Aluminium is the most common metallic element, but has no known biological role. It accumulates in the body when protective gastrointestinal mechanisms are bypassed, renal function is impaired, or exposure is high - all of which apply frequently to preterm infants. Recognised clinical manifestations of aluminium toxicity include dementia, anaemia and bone disease. Parenteral nutrition (PN) solutions are liable to contamination with aluminium, particularly from acidic solutions in glass vials, notably calcium gluconate. When fed parenterally, infants retain >75% of the aluminium, with high serum, urine and tissue levels. Later health effects of neonatal intravenous aluminium exposure were investigated in a randomised trial comparing standard PN solutions with solutions specially sourced for low aluminium content. Preterm infants exposed for >10 d to standard solutions had impaired neurologic development at 18 months. At 13-15 years, subjects randomised to standard PN had lower lumbar spine bone mass; and, in non-randomised analyses, those with neonatal aluminium intake above the median had lower hip bone mass. Given the sizeable number of infants undergoing intensive care and still exposed to aluminium via PN, these findings have contemporary relevance. Until recently, little progress had been made on reducing aluminium exposure, and meeting Food and Drug Administration recommendations (<5 μg/kg per d) has been impossible in patients <50 kg using available products. Recent advice from the UK Medicines and Healthcare regulatory Authority that calcium gluconate in small volume glass containers should not be used for repeated treatment in children <18 years, including preparation of PN, is an important step towards addressing this problem.

  15. No association between the aluminium content of trabecular bone and bone density, mass or size of the proximal femur in elderly men and women

    OpenAIRE

    Hellström, Hans-Olov; Mjöberg, Bengt; Mallmin, Hans; Michaëlsson, Karl

    2006-01-01

    Abstract Background Aluminium is considered a bone toxic metal since poisoning can lead to aluminium-induced bone disease in patients with chronic renal failure. Healthy subjects with normal renal function retain 4% of the aluminium consumed. They might thus also accumulate aluminium and eventually be at risk of long-term low-grade aluminium intoxication that can affect bone health. Methods We therefore examined 62 patients with femoral neck fractures or osteoarthritis of the hip (age range 3...

  16. Determination of chemical states of sulphur 35 obtained from the 35Cl (n, p)35S

    International Nuclear Information System (INIS)

    Rossi Filho, S.

    1980-01-01

    The chemical states of sulphur-35 obtained from the 35 Cl(n,p) 35 S reaction by the irradiation of potassium chloride without any previous treatment and with previous heating under vacuum, were determined. The influence of irradiation time and temperature after irradiation was examined. Paper electrophoresis technique was employed for the determination of the chemical states. (Author) [pt

  17. Microscopic observation of pattern attack by aggressive ions on finished surface of aluminium alloy sacrificial anode

    International Nuclear Information System (INIS)

    Zaifol Samsu; Muhammad Daud; Siti Radiah Mohd Kamarudin; Nur Ubaidah Saidin; Azali Muhammad; Mohd Shaari Ripin; Rusni Rejab; Mohd Shariff Sattar

    2010-01-01

    This paper presents the results of a microscopic observation on submerged finished surface of aluminium alloy sacrificial anode. Experimental tests were carried out on polished surface aluminium anode exposed to seawater containing aggressive ions in order to observe of pattern corrosion attack on corroding surface of anode. Results have shown, at least under the present testing condition, that surface of sacrificial anode were attack by an aggressive ion such as chloride along grain boundaries. In addition, results of microanalysis showed that the corrosion products on surface of aluminium alloy have Al, Zn and O element for all sample and within the pit was consists of Al, Zn, O and Cl element. (author)

  18. Development of cerium oxide and nickel oxide-incorporated aluminium matrix for marine applications

    International Nuclear Information System (INIS)

    Ashraf, P. Muhamed; Shibli, S.M.A.

    2009-01-01

    The present study signifies the role of nickel oxide along with cerium oxide on barrier protection of aluminium as a metal matrix composite for marine applications. The incorporation of cerium oxide and nickel oxide in pure aluminium had improved the corrosion resistance and microstructure of the composite. A relatively anodic and stable OCP was exhibited throughout the period during long-term evaluation. Both nickel oxide and cerium oxide acted synergistically to reduce corrosion in aluminium. The mechanisms of barrier protection of the composites are discussed predominantly based on extensive impedance analysis. The results signify the scope of potential use of the composite in marine environment.

  19. The aluminium content of breast tissue taken from women with breast cancer.

    Science.gov (United States)

    House, Emily; Polwart, Anthony; Darbre, Philippa; Barr, Lester; Metaxas, George; Exley, Christopher

    2013-10-01

    The aetiology of breast cancer is multifactorial. While there are known genetic predispositions to the disease it is probable that environmental factors are also involved. Recent research has demonstrated a regionally specific distribution of aluminium in breast tissue mastectomies while other work has suggested mechanisms whereby breast tissue aluminium might contribute towards the aetiology of breast cancer. We have looked to develop microwave digestion combined with a new form of graphite furnace atomic absorption spectrometry as a precise, accurate and reproducible method for the measurement of aluminium in breast tissue biopsies. We have used this method to test the thesis that there is a regional distribution of aluminium across the breast in women with breast cancer. Microwave digestion of whole breast tissue samples resulted in clear homogenous digests perfectly suitable for the determination of aluminium by graphite furnace atomic absorption spectrometry. The instrument detection limit for the method was 0.48 μg/L. Method blanks were used to estimate background levels of contamination of 14.80 μg/L. The mean concentration of aluminium across all tissues was 0.39 μg Al/g tissue dry wt. There were no statistically significant regionally specific differences in the content of aluminium. We have developed a robust method for the precise and accurate measurement of aluminium in human breast tissue. There are very few such data currently available in the scientific literature and they will add substantially to our understanding of any putative role of aluminium in breast cancer. While we did not observe any statistically significant differences in aluminium content across the breast it has to be emphasised that herein we measured whole breast tissue and not defatted tissue where such a distribution was previously noted. We are very confident that the method developed herein could now be used to provide accurate and reproducible data on the aluminium content

  20. F-35 Joint Strike Fighter Aircraft (F-35)

    Science.gov (United States)

    2015-12-01

    United States Marine Corps; United Kingdom; Italy; The Netherlands; Turkey; Canada ; Australia; Denmark; Norway The F-35 Program is a joint DoD...consistent engine deliveries. Recent quality escapes on turbine blades and electronic control systems resulted in maintenance activity to remove suspect...Short Takeoff and Vertical Landing Vpa - Max Approach Speed WOD - Wind Over the Deck F-35 December 2015 SAR March 21, 2016 08:47:09 UNCLASSIFIED 18 F-35

  1. An unconventional set-up for fluxless brazing of aluminium

    CERN Document Server

    Loos, Robert

    1999-01-01

    In order to successfully braze aluminium alloy assemblies without the use of oxide-removing fluxes, an evironment with very low contaminant level is mandatory. This is mostly achieved by using a vacuum furnace. Brazing under inert gas of sufficient purity is also possible. The method reported upon here makes use of a stainless steel bag which can enter a traditional air furnace. The bag is evacuated, giving a well distributed mechanical pressure on the parts to join. The intrinsic handicap of poor vacuum is compensated by regular inert gas flushing, even at high temperatures. The set-up works rather well, and the idea is believed to yield a valuable strategic and economic option, for the realization of special equipment as well as for prototyping work. We intend to use the principle for the CMS Preshower cooling screens.

  2. Electron stimulated desorption of gases at technological surfaces of aluminium

    International Nuclear Information System (INIS)

    Ding, M.Q.; Williams, E.M.

    1989-01-01

    The release of gas by electron bombardment at aluminium alloy surfaces in vacuum -9 torr has been investigated for a range of treatments including bakeout and glow discharge cleaning. Particular attention has been given to the role of continuous electron bombardment, with current densities and electron energies of up to 1.5 mA cm -2 and 2.0 keV, respectively, over the 10 cm 2 of surface area under irradiation. The observations of desorption efficiency, defined as the number of desorbed molecules per incident electron, conform to a model involving a dynamic balance between adsorption and desorption, with contributions to adsorption from both surface and sub-surface gas. Continuous electron bombardment promotes a surface with low desorption efficiency, -5 mol/electron, however, the conditioning cycle is accelerated significantly by glow discharge treatment. There is evidence of some short-term memory when the samples are exposed to air. (author)

  3. Intergranular area microalloyed aluminium-silicate ceramics fractal analysis

    Directory of Open Access Journals (Sweden)

    Purenović J.

    2013-01-01

    Full Text Available Porous aluminium-silicate ceramics, modified by alloying with magnesium and microalloying with alluminium belongs to a group of advanced multifunctional ceramics materials. This multiphase solid-solid system has predominantly amorphous microstructure and micro morphology. Intergranular and interphase areas are very complex, because they represent areas, where numbered processes and interactions take place, making new boundaries and regions with fractal nature. Fractal analysis of intergranular microstructure has included determination of ceramic grain fractal dimension by using Richardson method. Considering the fractal nature of intergranular contacts, it is possible to establish correlation between material electrical properties and fractal analysis, as a tool for future correlation with microstructure characterization. [Projekat Ministarstva nauke Republike Srbije, br. ON 172057 i br. III 45012

  4. Friction stir welding of Aluminium matrix composites – A Review

    Directory of Open Access Journals (Sweden)

    Subramanya Prabhu

    2018-01-01

    Full Text Available Friction stir welding (FSW is established as one of the prominent welding techniques to join aluminium matrix composites (AMCs. It is a solid state welding process, takes place well below the melting temperature of the material, eliminates the detrimental effects of conventional fusion welding process. Although the process is capable to join AMCs, challenges are still open that need to be fulfill to widen its applications. This paper gives the outline of the friction stir welding technique used to join AMCs. Effect of process variables on the microstructure and mechanical properties of the joints, behavior of reinforcing materials during welding, effect of tool profiles on the joint strength are discussed in detail. Few improvements and direction for future research are also proposed.

  5. Designing aluminium friction stir welded joints against multiaxial fatigue

    Directory of Open Access Journals (Sweden)

    L. Susmel

    2016-07-01

    Full Text Available The present paper investigates the accuracy of the Modified Wöhler Curve Method (MWCM in estimating multiaxial fatigue strength of aluminium friction stir (FS welded joints. Having developed a bespoke joining technology, circumferentially FS welded tubular specimens of Al 6082-T6 were tested under proportional and non-proportional tension and torsion, the effect of non-zero mean stresses being also investigated. The validation exercise carried out using the experimental results have demonstrated that the MWCM applied in terms of nominal stresses, notch stresses, and also the Point Method is accurate in predicting the fatigue lifetime of the tested FS welded joints, with its use resulting in life estimates that fall within the uniaxial and torsional calibration scatter bands.

  6. Corrosion behaviour of aluminium plates in aqueous medium

    International Nuclear Information System (INIS)

    Oliveira, M.F. de; Gaio, J.C.

    1985-01-01

    The process of corrosion concerning the aluminium 1050 plate was studied at room temperatures, 45 and 60 0 C in deionized water, the same Argonauta Reactor Water. Beyond the temperature influence, it was verified the effect of chloride ion and oxygen. It ws found that the amount of oxyde formed at room temperatures is almost negligible; at 45 and 60 0 C the samples were covered with bayerita, the quantity of oxide formed at 45 0 C being higher than at 60 0 C. It was observed that there will be risk of corrosion in the case of Reactor Water to undergo contamination with chloride ions. The results have shown that the material can be used since the medium don't be strongly oxidizing. At potentials higher than - 900M sup(V) ess (-280 m sup(V) sub(H)), the material will undergo pitting corrosion. (Author) [pt

  7. Monotonic and cyclic deformation behaviour of ultrafine-grained aluminium

    International Nuclear Information System (INIS)

    May, J.; Amberger, D.; Dinkel, M.; Hoeppel, H.W.; Goeken, M.

    2008-01-01

    The effect of the enhanced strain-rate sensitivity (SRS) of ultrafine-grained commercially pure aluminium Al 99.5 on the mechanical properties under monotonic as well as under cyclic loading was investigated. Compared with the conventional grain-sized counterpart, for the monotonic tests, a strongly enhanced strength combined with a high ductility was obtained, depending on the strain rate. The enhanced SRS also affects the cyclic deformation behaviour and the fatigue lives. At a lower strain rate shorter fatigue lives and a different cyclic hardening behaviour are observed. Microstructural changes during cyclic deformation are investigated by X-ray diffraction profile analysis. Based on the fatigue behaviour and the X-ray diffraction profile analysis, thermally activated annihilation processes of dislocations are regarded to be the relevant deformation mechanism leading to enhanced SRS and ductility

  8. Fractographic analysis of fatigue damage in 7000 aluminium alloys.

    Science.gov (United States)

    Cvijović, Z; Vratnica, M; Gerić, K

    2008-12-01

    In this paper, an attempt is made to correlate the fatigue damage in 7000 aluminium alloys with different impurity contents to the microstructural features and to explain their interdependence through fractographic observations. The Paris constants of these alloys in the form of hot-forged plates subjected to the overaged T73 temper are evaluated and differences in the fatigue crack growth rate described by striation spacing measurements. Scanning electron microscopy analysis of fatigue fracture surfaces revealed that the type and morphological parameters of coarse intermetallic particles play a critical role in fatigue crack growth behaviour. The elemental distribution determined by means of energy-dispersive spectroscopy analysis showed that the fractured particles accelerating the crack advances are larger particles of Fe-rich phases. The fatigue crack growth rate increases considerably with increasing amounts of these particles. The smaller eta, S and Mg(2)Si particles contribute beneficially to fatigue life.

  9. Experimental study of impact properties of aluminium honeycomb sandwich structure

    Directory of Open Access Journals (Sweden)

    Flasar Ondrej

    2017-01-01

    Full Text Available Aircraft grade of structural sandwich plates has been studied to determine the influence rate of particular face sheets adjustments on impact energy absorption. The face sheets were fabricated by carbon fibre reinforced plastic (CFRP laminas using unidirectional reinforcement with either cross-ply [0/90]n or angle-ply [±45]n orientation of fibres. A core of the sandwich plates was then formed by aluminium honeycomb. The impact properties of small unnotched sandwich specimens were measured by instrumented Charpy impact test device. Assessment of force-displacement curve, loading process and failure mode was carried out for each specimen type to determine a general trend for increasing the impact properties of sandwich structures.

  10. Metallography of the indented aluminium sheet fracture surfaces

    International Nuclear Information System (INIS)

    Khan, M.A.; Qaiser, S.; Haq, A.U.; Atkins, A.G.

    1997-01-01

    It was experimentally observed that indentation of aluminium sheet samples with a sharp tool leads the off cut metal into a flare out-curvature, whose shape depends upon the geometry of the tool, applied force, displacement, material properties etc. The crack initiation, crack propagation and fracture surfaces were studied. Type grain, fibers, cut marks and voids were analyzed on optical and scanning electron microscopes to see how these were produced,. and their relationship to the material inherent properties, since this phenomenon has hot been studied so far. The sharp tool angles were responsible for the plastic flow. Plastic work per volume, fracture toughness and deformation area of the indented material. The metallographic information provided details of sheet metal deformation, and failure into the particular shapes represented on the fracture surfaces. (author)

  11. Tattoo removal by Q-switched yttrium aluminium garnet laser

    DEFF Research Database (Denmark)

    Hutton Carlsen, K; Esmann, J; Serup, J

    2017-01-01

    BACKGROUND: Tattoo removal by Q-switched yttrium aluminium garnet (YAG) lasers is golden standard; however, clients' satisfaction with treatment is little known. OBJECTIVE: To determine clients' satisfaction with tattoo removal. METHODS: One hundred and fifty-four tattoo removal clients who had...... attended the private clinic 'Centre for Laser Surgery', Hellerup, Denmark, from 2001 to 2013 completed a questionnaire concerning outcome expectations, level of pain experiences and satisfaction with tattoo removal. The laser surgeon and his team were blinded from data handling. The study design included...... relative to colour of tattoo on a scale from 0 (no effect) to 10 (complete removal) scored a mean of blue 9.5, black 9.4, yellow 8.9, red 8.8 and green 6.5. Clients were dissatisfied with green pigment remnants, which could mimic bruising. One hundred and twenty-nine clients (84%) experienced moderate...

  12. Electron beam induced heat flow transient in aluminium

    International Nuclear Information System (INIS)

    Dalle Rose, L.F.D.; Brotto, R.

    1983-01-01

    On the basis of a numerically solved heat diffusion equation, the structure of the thermal transient induced in an aluminium sample by an electron beam pulse is described in terms of slush zone formation, molten depth, liquid phase duration, and melt front history. The heat flow dynamics, as determined by monochromatic (electron energy ranging between 5 and 25 keV) and ultrashort (15 ns fwhm) pulses, is contrasted with the ruby laser induced one. Accessible absorbed energy intervals for sample surface melting are given as a function of electron energy; heating of the sample interior at values higher than those attained at the surface is shown to occur only at higher electron energies, for a given pulse duration. The general dependence of the present results on the pulse duration and the effects produced by polychromatic pulses are also discussed. (author)

  13. Corrosion behaviour of aluminium matrix composites containing silicon carbide particles

    Energy Technology Data Exchange (ETDEWEB)

    Harris, S.J. [Nottingham Univ. (United Kingdom). Dept. of Materials Engineering and Materials Design; Noble, B. [Nottingham Univ. (United Kingdom). Dept. of Materials Engineering and Materials Design; Trowsdale, A.J. [Nottingham Univ. (United Kingdom). Dept. of Materials Engineering and Materials Design

    1996-12-31

    An examination of the pitting attack in two aluminium matrix composites (1050 and 2124) each reinforced with varying fractions (0-30 wt.%) of silicon carbide particles (SiC{sub p}) in the size range 3-40 {mu}m has been made in 1 N NaCl solution. It has been demonstrated that the existence of pores and crevices at SiC{sub p}/matrix interfaces strongly influences pit initiation. This is further aided by the cracking of large SiC{sub p}{>=}20 {mu}m, during processing. The presence of {theta}(CuAl{sub 2}) and S(CuMgAl{sub 2}) precipitates in 2124-SiC{sub p} composite also promotes pitting attack at SiC{sub p}-matrix and intermetallic-matrix interfaces. (orig.)

  14. Determination of uranium in samples containing bulk aluminium

    International Nuclear Information System (INIS)

    Das, S.K.; Kannan, R.; Dhami, P.S.; Tripathi, S.C.; Gandhi, P.M.

    2015-01-01

    The determination of uranium is of great importance in PUREX process and need to be analyzed at different concentration ranges depending on the stage of reprocessing. Various techniques like volumetry, spectrophotometry, ICP-OES, fluorimetry, mass spectrometry etc. are used for the measurement of uranium in these samples. Fast and sensitive methods suitable for low level detection of uranium are desirable to cater the process needs. Microgram quantities of uranium are analyzed by spectrophotometric method using 2-(5- bromo-2-pyridylazo-5-diethylaminophenol) (Br-PADAP) as the complexing agent. But, the presence of some of the metal ions viz. Al, Pu, Zr etc. interferes in its analysis. Therefore, separation of uranium from such interfering metal ions is required prior to its analysis. This paper describes the analysis of uranium in samples containing aluminium as major matrix

  15. Parameter subset selection based damage detection of aluminium frame structure

    International Nuclear Information System (INIS)

    Titurus, B; Friswell, M I

    2011-01-01

    A three storey aluminium frame structure was tested in multiple damage cases. All damage scenarios, simulated by the localized stiffness changes, were associated with joint areas of the structure. Further, between damage tests the structure was returned to its healthy reference conditions and was again measured. In this paper, a parameter subset selection methodology is applied to an updated finite element model of the structure, together with a previously demonstrated approach employing concepts of model sensitivity subspace angles, first order model representation and mixed response residuals for damage detection. The objective of this paper is the evaluation of these methods on a real experimental structure with significant complexity, represented by an imprecise reference mathematical model and in the environment with uncertain reference structural state. The questions of symmetry, mixed response residuals and semi-localized parameterization are also addressed in this work.

  16. Aluminium and lead: molecular mechanisms of brain toxicity.

    Science.gov (United States)

    Verstraeten, Sandra V; Aimo, Lucila; Oteiza, Patricia I

    2008-11-01

    The fact that aluminium (Al) and lead (Pb) are both toxic metals to living organisms, including human beings, was discovered a long time ago. Even when Al and Pb can reach and accumulate in almost every organ in the human body, the central nervous system is a particular target of the deleterious effects of both metals. Select human population can be at risk of Al neurotoxicity, and Al is proposed to be involved in the etiology of neurodegenerative diseases. Pb is a widespread environmental hazard, and the neurotoxic effects of Pb are a major public health concern. In spite of the numerous efforts and the accumulating evidence in this area of research, the mechanisms of Al and Pb neurotoxicity are still not completely elucidated. This review will particularly address the involvement of oxidative stress, membrane biophysics alterations, deregulation of cell signaling, and the impairment of neurotransmission as key aspects involved Al and Pb neurotoxicity.

  17. Plasmonic Colour Filters Based on Coaxial Holes in Aluminium

    Directory of Open Access Journals (Sweden)

    Ranjith Rajasekharan Unnithan

    2017-04-01

    Full Text Available Aluminum is an alternative plasmonic material in the visible regions of the spectrum due to its attractive properties such as low cost, high natural abundance, ease of processing, and complementary metal-oxide-semiconductor (CMOS and liquid crystal display (LCD compatibility. Here, we present plasmonic colour filters based on coaxial holes in aluminium that operate in the visible range. Using both computational and experimental methods, fine-tuning of resonance peaks through precise geometric control of the coaxial holes is demonstrated. These results will lay the basis for the development of filters in high-resolution liquid crystal displays, RGB-spatial light modulators, liquid crystal over silicon devices and novel displays.

  18. Radiative capture of polarized neutrons by aluminium and manganese nuclei

    International Nuclear Information System (INIS)

    1979-01-01

    This investigation treats the angular dependence of the intensity and of the circular polarization of gamma-radiation, that is emitted after capture of polarized neutrons by polarized and unpolarized targets. Interference effects between the (n,γ)-reaction amplitudes with different channel spin are discussed and angular distribution coefficients are calculated in case mixing of dipole and quadrupole radiation occurs. It is indicated how the influence of p-wave capture may be taken into account. The nuclear orientation experiments on aluminium yield the values of the angular distribution coefficients of primary and secondary gamma-ray transitions and by a chi 2 -analysis five spin values are assigned uniquely and several α-values are determined. The nuclear orientation experiments on manganese lead to α-values and unique spin assigments for thirteen nuclear states in 56 Mn. (Auth.)

  19. Natural gas anodes for aluminium electrolysis in molten fluorides.

    Science.gov (United States)

    Haarberg, Geir Martin; Khalaghi, Babak; Mokkelbost, Tommy

    2016-08-15

    Industrial primary production of aluminium has been developed and improved over more than 100 years. The molten salt electrolysis process is still suffering from low energy efficiency and considerable emissions of greenhouse gases (CO2 and PFC). A new concept has been suggested where methane is supplied through the anode so that the CO2 emissions may be reduced significantly, the PFC emissions may be eliminated and the energy consumption may decrease significantly. Porous carbon anodes made from different graphite grades were studied in controlled laboratory experiments. The anode potential, the anode carbon consumption and the level of HF gas above the electrolyte were measured during electrolysis. In some cases it was found that the methane oxidation was effectively participating in the anode process.

  20. Verification of Some Vegetable Oils as Cutting Fluid for Aluminium

    Directory of Open Access Journals (Sweden)

    A. I. Obi

    2013-06-01

    Full Text Available Vegetable oils (palm oil, groundnut oil, shear butter oil and cotton seed oil have been used as lubricants in the turning operation of aluminum under varying spindle speeds, feed rates and depths of cut and the results compared with kerosene (due to the gummy nature of aluminium metal. The parameters investigated are the chip thickness ratio, surface finish and surface temperature. Their performances when compared with the conventional soluble oil have shown that they can perform the same functions as imported ones in the machining of aluminum. They reduced chip thickness ratio, improved surface finish and exhibited good cooling behaviour at the work piece-tool interface. This performance is due to their high viscosities and the presence of surface active agents such as stearic acid and halogens, such as chlorine which help to reduce surface energy of a liquid and increase its wetting ability or oiliness.

  1. 3D printing of high-strength aluminium alloys

    Science.gov (United States)

    Martin, John H.; Yahata, Brennan D.; Hundley, Jacob M.; Mayer, Justin A.; Schaedler, Tobias A.; Pollock, Tresa M.

    2017-09-01

    Metal-based additive manufacturing, or three-dimensional (3D) printing, is a potentially disruptive technology across multiple industries, including the aerospace, biomedical and automotive industries. Building up metal components layer by layer increases design freedom and manufacturing flexibility, thereby enabling complex geometries, increased product customization and shorter time to market, while eliminating traditional economy-of-scale constraints. However, currently only a few alloys, the most relevant being AlSi10Mg, TiAl6V4, CoCr and Inconel 718, can be reliably printed; the vast majority of the more than 5,500 alloys in use today cannot be additively manufactured because the melting and solidification dynamics during the printing process lead to intolerable microstructures with large columnar grains and periodic cracks. Here we demonstrate that these issues can be resolved by introducing nanoparticles of nucleants that control solidification during additive manufacturing. We selected the nucleants on the basis of crystallographic information and assembled them onto 7075 and 6061 series aluminium alloy powders. After functionalization with the nucleants, we found that these high-strength aluminium alloys, which were previously incompatible with additive manufacturing, could be processed successfully using selective laser melting. Crack-free, equiaxed (that is, with grains roughly equal in length, width and height), fine-grained microstructures were achieved, resulting in material strengths comparable to that of wrought material. Our approach to metal-based additive manufacturing is applicable to a wide range of alloys and can be implemented using a range of additive machines. It thus provides a foundation for broad industrial applicability, including where electron-beam melting or directed-energy-deposition techniques are used instead of selective laser melting, and will enable additive manufacturing of other alloy systems, such as non-weldable nickel

  2. Remelting of Aluminium by Continuous Submersion of Rolled Scrap

    Energy Technology Data Exchange (ETDEWEB)

    Farner, Snorre

    2000-12-01

    When remelting aluminium scrap, metal losses due to dross generation is a common problem. Reduction of these losses will give substantial economic and environmental benefits. Dross is generated when aluminium metal oxidizes and films of oxide envelope molten metal. When a cold metal object is immersed in a melt, the heat of the melt around this is transferred so rapidly into the object that a shell of melt often solidifies to the surface of the object. When scrap with low bulk density is charged to a melt, solidification of melt on the cold scrap prevents melt from entering the cavities in the bulk of the scrap, and the bulk density remains low. Thus the scrap tends to float on the melt surface. Submersion of this scrap is important to avoid oxidation and subsequent dross generation. One solution to this is to roll scrap to a strip and feed it into the melt. This system has been examined by studying feeding of a continuous, thin aluminium plate into molten aluminium. Also, the effect of lacquer was considered, as well as feeding the plate into a launder with melt flowing along the surface of the plate. An analytical, one-dimensional, steady-state model has been developed to describe the melting and the melting mechanisms. It is based on a shell solidifying on the plate surface and a gap introducing a thermal resistance 1/h{sub g} between the shell and the plate. The thermal resistance 1/h{sub l} of the boundary layer of the melt is included. Depending on these resistances, the initial temperature of the plate and the melt temperature, a shell will form, and the plate will penetrate a distance P into the melt before it melts away. An experimental apparatus was designed and constructed to feed aluminium plate from a coil into a melt bath at a specified velocity. The plate could be withdrawn rapidly to ''freeze'' the situation like it was below the melt surface. The penetration depth P of the plate could be measured and shell formation observed

  3. Evaluation of Aluminium Dross as Adsorbent for Removal of Carcinogenic Congo Red Dye in Wastewater

    Science.gov (United States)

    Zakaria, Mohamad Zulfika Hazielim b.; Zauzi, Nur Syuhada Ahmad; Baini, Rubiyah; Sutan, Norsuzailina Mohamed; Rezaur Rahman, Md

    2017-06-01

    In this study, aluminium dross waste generated from aluminium smelting industries was employed as adsorbent in removing of congo red dye in aqueous solution. The raw aluminium dross as adsorbent was characterized using Scanning Electron Microscope (SEM), Brunauer-Emmett-Teller (BET) for surface area and X-Ray Fluorescence (XRF) Spectroscopy. Adsorption experiments were carried out by batch system at different adsorbent mass, pH, and initial dye concentration. The results showed that the per cent removal of dye increased as adsorbent mass increased. It was found that 0.4 gram of adsorbent can remove approximately 100 % of dye at pH 9 for dye concentration 20 and 40 ppm. Therefore, it can be concluded that raw aluminium dross without undergone any treatment can be effectively used for the adsorption of congo red in textile wastewater related industries.

  4. Sub-structure and mechanical properties of twist channel angular pressed aluminium

    Czech Academy of Sciences Publication Activity Database

    Kocich, R.; Kunčická, L.; Král, Petr; Macháčková, A.

    2016-01-01

    Roč. 119, SEP (2016), s. 75-83 ISSN 1044-5803 Institutional support: RVO:68081723 Keywords : Aluminium * Dislocations * Electron microscopy Subject RIV: JG - Metallurgy Impact factor: 2.714, year: 2016

  5. Observations on biofilm bacteria isolated from aluminium panels immersed in estuarine waters

    Digital Repository Service at National Institute of Oceanography (India)

    Sonak, S.; Bhosle, N.B.

    Microfouling biomass generally increased on aluminium panels immersed in the surface waters of a tropical estuary over a period of 30 d. A hundred bacterial colonies were randomly isolated, purified and morphologically, physiologically...

  6. Anti-corrosive Conversion Coating on Aluminium Alloys Using High Temperature Steam

    DEFF Research Database (Denmark)

    Din, Rameez Ud; Jellesen, Morten Stendahl; Ambat, Rajan

    Aluminium is extensively used as a structural material due to its excellent strength to weight ratio and corrosion resistance properties. The surface of aluminium under normal conditions has a thin oxide film (1-10nm) which provides corrosion resistance. However due to lower thickness, flaws...... and heterogeneity of native oxide layer does not provide long time corrosion resistance and adhesion of organic coating for a particular function in different environments. In order to enhance the corrosion resistance and adhesion of organic coating, the aluminium native oxide layer is treated to transform...... or convert to a functional conversion coating. In the last several decades chromate conversion coating (CrCCs) have been the most common conversion coatings used for aluminium alloys. Due to the toxicity of the hexavalent chrome, however, environmental friendly alternatives to CrCCs have been investigated...

  7. Contradictory effect of chromate inhibitor on corrosive wear of aluminium alloy

    International Nuclear Information System (INIS)

    Pokhmurskii, V.I.; Zin, I.M.; Vynar, V.A.; Bily, L.M.

    2011-01-01

    Research highlights: → Corrosive wear of aluminium alloy in inhibited artificial acid rain was studied. → Tribometer with linear reciprocating ball-on-flat geometry was used.→ Corrosion potential, polarization current and friction coefficient were measured. → Chromate decreases corrosion of aluminium alloy under wear conditions. → Chromate in general accelerates corrosive wear of the alloy in acid rain. - Abstract: The corrosive wear of D16T aluminium alloy in artificial acid rain was studied. A special tribometer with the linear reciprocating ball-on-flat geometry was used. The setup allows to measure simultaneously an open circuit potential, to carry out potentiostatic and potentiodynamic polarization studies of the alloy corrosion and to record the friction coefficient. It was established that the addition of strontium chromate inhibitor to the working environment decreases an electrochemical corrosion of the aluminium alloy under wear conditions, but in general accelerates its destruction due to insufficient wear resistance of a formed surface film.

  8. Biological and biochemical characterization of microfouling on aluminium panels placed in the Arabian Sea

    Digital Repository Service at National Institute of Oceanography (India)

    Bhosle, N.B.; Nandakumar, K.; Venkat, K.; Dhople, V.M.; Sawant, S.S.; Wagh, A.B.; Kelkar, P.G.

    Microfouling biomass was higher in the shelf waters (< 200 m) as compared with the slope waters (> 200 m). Bacteria were first to colonize on the aluminium surfaces as irregular formations during the initial stages of fouling. The number of fouling...

  9. Synthesis of Aluminium Nanoparticles in A Water/Polyethylene Glycol Mixed Solvent using μ-EDM

    Science.gov (United States)

    Sahu, R. K.; Hiremath, Somashekhar S.

    2017-08-01

    Nanoparticles present a practical way of retaining the results of the property at the atomic or molecular level. Due to the recent use of nanoparticles in scientific, industrial and medical applications, synthesis of nanoparticles and their characterization have become considerably important. Currently, aluminium nanoparticles have attracted significant research attention because of their reasonable cost, unique properties and interdisciplinary emerging applications. The present paper reports the synthesis of aluminium nanoparticles in the mixture of Deionized water (DI water) and Polyethylene Glycol (PEG) using a developed micro-Electrical Discharge Machining (μ-EDM) method. PEG was used as a stabilizer to prevent nanoparticles from agglomeration produced during the μ -EDM process. The synthesized aluminium nanoparticles were examined by Transmission Electron Microscopy (TEM), Energy Dispersive Analysis by X-rays (EDAX) and Selected Area Electron Diffraction (SAED) pattern to determine their size, shape, chemical nature and crystal structure. The average size of the polyhedral aluminium nanoparticles is found to be 196 nm.

  10. Treatment of aluminium dust by aqueous dissolution; Tratamiento del polvo de aluminio mediante disolucion acuosa

    Energy Technology Data Exchange (ETDEWEB)

    Lopez, F. A.; Medina, J.; Gutierrez, A.; Taybi, H.; Pena, C.; Lopez-Delgado, A.

    2004-07-01

    Aluminium dust from aluminium remelting industry is a hazardous residue because of its high reactivity in the presence of water. In order to apply the new European Directive about landfill of waste, a study of its hydrolysis was carried out. The influence of temperature, time and pH on the hydrolysis of the aluminium dust was studied. The hydrolysed solids were characterized by XRD and AAS; in the aqueous solutions the pH and the ionic conductivity were determined. The evolved gases were analysed by mass spectrometry. The reactivity of the dust , before and after hydrolysis, was investigated by analysing the ammonia, hydrogen sulphide and metallic aluminium. By hydrolysis at 60 degree centigree and 48 h a much lower reactive material was obtained which could be disposed with minimal environmental impact. (Author) 7 refs.

  11. Evaluation of mechanical properties of aluminium alloy–alumina–boron carbide metal matrix composites

    International Nuclear Information System (INIS)

    Vijaya Ramnath, B.; Elanchezhian, C.; Jaivignesh, M.; Rajesh, S.; Parswajinan, C.; Siddique Ahmed Ghias, A.

    2014-01-01

    Highlights: • Fabrication of MMC with aluminium alloy–alumina–boron carbide is done. • Different proportions of reinforcements are added. • The effects of varying proportions are studied. • Investigation on mechanical properties above composites is performed. • Failure morphology analysis is done using SEM. - Abstract: This paper deals with the fabrication and mechanical investigation of aluminium alloy, alumina (Al 2 O 3 ) and boron carbide metal matrix composites. Aluminium is the matrix metal having properties like light weight, high strength and ease of machinability. Alumina which has better wear resistance, high strength, hardness and boron carbide which has excellent hardness and fracture toughness are added as reinforcements. Here, the fabrication is done by stir casting which involves mixing the required quantities of additives into stirred molten aluminium. After solidification, the samples are prepared and tested to find the various mechanical properties like tensile, flexural, impact and hardness. The internal structure of the composite is observed using Scanning Electron Microscope (SEM)

  12. [Providing safe environment for health of population living near aluminium industry enterprises].

    Science.gov (United States)

    Plotko, E G; Kuz'min, S V; Gurvich, V B; Seliankina, K P; Privalova, L I; Ryzhov, V V; makarenko, N P; Vinokurova, M V; Domnin, S G; Pozhidaeva, T Ia

    2004-01-01

    Based on studies of environmental objects and of children's health, the authors justified systematic approach to hygienic evaluation of aluminium plant reconstruction stages, for rational management in minimizing risk of environmental pollution and for health preservation.

  13. GAS-CREATION OF SEPARATING COVERINGS FOR MOULDS FOR DIE CASTING OF ALUMINIUM ALLOYS

    Directory of Open Access Journals (Sweden)

    A. M. Mihaltsov

    2010-01-01

    Full Text Available The methods of experiments on determination of gascreating ability of different separating coverings for the moulds of aluminium alloys die casting are given and described in the article, and the results of investigation are given as well.

  14. The distribution and phylogeny of aluminium accumulating plants in the Ericales

    NARCIS (Netherlands)

    Jansen, S.; Watanabe, T.; Caris, P.; Geuten, K.; Lens, F.; Pyck, N.; Smets, E.

    2004-01-01

    The distribution of aluminium (Al) accumulation in the Ericales is surveyed, based on semi-quantitative tests of 114 species and literature data. Al accumulation mainly characterises the families Diapensiaceae, Pentaphylacaceae, Symplocaceae, Ternstroemiaceae, and Theaceae. Al accumulation is

  15. In-situ electron microscopy studies on the tensile deformation mechanisms in aluminium 5083 alloy

    CSIR Research Space (South Africa)

    Motsi, G

    2014-10-01

    Full Text Available In this study tensile deformation mechanisms of aluminium alloy 5083 were investigated under observations made from SEM equipped with a tensile stage. Observations during tensile testing revealed a sequence of surface deformation events...

  16. A reliability based stress-life evaluation of aluminium-graphite particulate composites

    International Nuclear Information System (INIS)

    Achutha, M.V.; Sridhara, B.K.; Abdul Budan, D.

    2008-01-01

    Fatigue tests were conducted on sand cast aluminium-graphite composite specimens on Rotating Beam Fatigue Testing Machine with three different stress levels. Aluminium-graphite (LM 25-5% graphite) composite was processed by closed mould sand casting method. Three-stress level fatigue test program was planned for carrying out fatigue experiments. Three different stress levels selected for fatigue experiments were a fraction of ultimate tensile strength. Statistical design of fatigue experiments was carried out to determine the sample size at each stress level. Experimental results are presented in the form of stress-life (S-N) curves and reliability-stress-life (R-S-N) curves, which are helpful for designers. The S-N curve of the aluminium-graphite composite was compared with its matrix alloy LM 25. Comparison revealed that the fatigue behaviour of the aluminium-graphite composite is superior to that of the matrix alloy

  17. Structural characterisation of aluminium layered double hydroxides by (27)Al solid-state NMR.

    Science.gov (United States)

    Vyalikh, Anastasia; Massiot, Dominique; Scheler, Ulrich

    2009-09-01

    (27)Al solid-state NMR has been applied to study the local structure of pristine and chemically modified aluminium layered double hydroxides (LDH). The pristine LDH only shows six-fold coordinated, octahedral, aluminium, while the calcined and subsequently surfactant treated LDH sample shows a significant fraction of four-fold coordinated tetrahedral aluminium. The co-existence of two types of octahedral sites with different quadrupolar parameters is clearly observed in both samples. Quadrupolar coupling constants and isotropic chemical shifts have been measured from the (27)Al triple-quantum MAS NMR allowing to fit the (27)Al MAS spectra and quantify the different species in the samples. The quantitative analysis reveals that 30% of the aluminium is in four-fold coordination in the surfactant-modified LDH. We show that this chemical modification retains the two types of AlO(6) sites with a decreased intensity of the site showing the lowest quadrupolar coupling constant.

  18. Composition of microfouling on aluminium and fibre glass panels exposed in Agatti waters (Lakshadweep Island)

    Digital Repository Service at National Institute of Oceanography (India)

    Raveendran, T.V.; Sankaran, P.D.; Wagh, A.B.

    Rate of microfouling build-up was high during the initial periods of exposure of test surfaces but decreased with the increasing duration. Fibre glass surfaces showed higher deposition than those of aluminium. Carbohydrates and lipids were the major...

  19. Modélisation du durcissement cyclique de l'aluminium produit au ...

    African Journals Online (AJOL)

    hardening is a very significant parameter to traduce the elastoplastic behaviour of materials, particularly for the simulation of their working by plastic deformation. This paper presents a model of cyclic hardening of two nuances of aluminium ...

  20. Role of Root Exudates in Adaptative Reactions of Buckwheat Plants in Aluminium-acid Stress

    Directory of Open Access Journals (Sweden)

    A.E. Smirnov

    2014-03-01

    Full Text Available Aliminium toxicity is major limiting factor of crop production in acidic soils. It is known that mechanisms of toxic effects of aluminium are differing in biochemical characters, research of aluminium toxicity complicated by variety of its chemical forms and migration in soil and water ability. The root exudates qualitative composition of common buckwheat was evaluated. Organic complexing agents – oxalic acid and phenolic compounds were revealed. The role of these complexing agents in the buckwheat aluminium resistance under acidic stress, participation in processes of external and internal detoxification was shown. Spectrophometric assay revealed an increase in root secretion of oxalic acid by 2.5 times and decrease in content of phenolic compounds in root exudates solution by 3 times upon aluminium (50 µM treatment. In the meanwhile the same concentration of the metal had induced phenylalanine ammonia-lyase activity by 2 times.

  1. Inhibition of ethylene production by putrescine alleviates aluminium-induced root inhibition in wheat plants

    OpenAIRE

    Yu, Yan; Jin, Chongwei; Sun, Chengliang; Wang, Jinghong; Ye, Yiquan; Zhou, Weiwei; Lu, Lingli; Lin, Xianyong

    2016-01-01

    Inhibition of root elongation is one of the most distinct symptoms of aluminium (Al) toxicity. Although putrescine (Put) has been identified as an important signaling molecule involved in Al tolerance, it is yet unknown how Put mitigates Al-induced root inhibition. Here, the possible mechanism was investigated by using two wheat genotypes differing in Al resistance: Al-tolerant Xi Aimai-1 and Al-sensitive Yangmai-5. Aluminium caused more root inhibition in Yangmai-5 and increased ethylene pro...

  2. Comparison of Chemical Coagulation and Electrocoagulation for Boron Removal from Synthetic Wastewater Using Aluminium

    OpenAIRE

    Kartikaningsih Danis; Yao-Hui Huang

    2016-01-01

    Various techniques including conventional and advanced have been employed for the boron treatment from water and wastewater. The electrocoagulation involves an electrolytic reactor for coagulation/flotation with aluminium as anode and cathode. There is aluminium as coagulant to be used for removal which may induce secondary pollution in chemical coagulation. The purpose of this study is to investigate and compare the performance between electrocoagulation and chemical coagulation on boron rem...

  3. Inhibition de corrosion des échangeurs thermiques en aluminium et ...

    African Journals Online (AJOL)

    Ainsi, on peut trouver dans un même circuit de chauffage central la chaudière en aluminium, la tuyauterie en cuivre et les radiateurs en fonte, acier ou aluminium et aussi des matériaux polymères. Nous décrivons un nouvel inhibiteur de corrosion spécifiquement conçu pour protéger les circuits de chauffage central dans ...

  4. Life Cycle Assessment of Aluminium Recycling Process: Case of Shredder Cables

    OpenAIRE

    GRIMAUD, Guilhem; PERRY, Nicolas; LARATTE, Bertrand

    2016-01-01

    Life cycle impact of European generic primary and secondary aluminium are well defined. However specific recycling processes are not available in literature. In this study, the environmental assessment of cable recycling processing is examined. The data come from a recycling plant (MTB Recycling) in France. MTB process relies only on mechanical separation and optical sorting processes on shredder cables. On the one hand, the study demonstrates huge environmental benefits for aluminium recycle...

  5. Influence of aluminium content on thermodynamic function of LaNi5-xAlx

    International Nuclear Information System (INIS)

    Xiong Yifu; Cheng Huchi; Luo Deli

    2000-01-01

    Hydriding thermodynamic parameters were measured on alloys of the general composition of LaNi 5-x Al x (x = 0.0, 0.1, 0.2, 0.3) under isothermal and isochoric conditions. The results show that the equilibrium pressure, hydrogen capacity and thermodynamic parameters such as ΔH, ΔS decrease with aluminium content, plateau slopes of the P-C-T curve increase with aluminium content

  6. Toxic effects of aluminium and its concentrations in different brands of malaysian tea

    International Nuclear Information System (INIS)

    Peerzada, N. H.; Tariq, S. A.

    2001-01-01

    The effect of air pollution is felt world wide. Acid rain brings havoc to all forms of life on this planet. One of the many consequences of acid rain is the release of luminum (III) from the soil. Tea is the plant which selectively accumulates soluble aluminium from the soil. The short article is to alert heavy tea drinkers as aluminium is a neuro-toxic metal. (author)

  7. Aluminium bismuthate nanorods and the electrochemical performance for detection of tartaric acid

    Energy Technology Data Exchange (ETDEWEB)

    Pei, L.Z., E-mail: lzpei@ahut.edu.cn [Key Lab of Materials Science and Processing of Anhui Province, School of Materials Science and Engineering, Anhui University of Technology, Ma' anshan, Anhui 243002 (China); Wei, T.; Lin, N.; Fan, C.G. [Key Lab of Materials Science and Processing of Anhui Province, School of Materials Science and Engineering, Anhui University of Technology, Ma' anshan, Anhui 243002 (China); Yang, Zao, E-mail: yangzao888@tom.com [National Engineering Research Center for Biomaterials, Sichuan University, Chengdu, Sichuan 610064 (China)

    2016-09-15

    Aluminium bismuthate nanorods had been synthesized by a facile hydrothemral method. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations showed that the lengh and diameter were 2–10 μm and 50–200 nm, respectively. X-ray diffraction (XRD) and high-resolution TEM (HRTEM) showed that the nanorods were composed of single crystalline orthorhombic Al{sub 4}Bi{sub 2}O{sub 9} phase. The aluminium bismuthate nanorods could be explained by the nucleation and crystalline growth process based on the products obtained from different hydrothermal conditions. Aluminium bismuthate nanorods modified glassy carbon electrode (GCE) was fabricated for the electrochemical detection of tartaric acid (TA) in neutral solution. A pair of semi-reversible redox peaks located at −0.08 V and −0.53 V, respectively were observed. The current intensity of the cyclic voltammogram (CV) peak increased linearly obviously with increasing the scan rate and TA concentration. The detection limit and linear range were 0.64 μM and 0.001–2 mM, respectively with the correlation coefficient of 0.995. The aluminium bismuthate nanorods modified GCE had good reproducibility and stability for the detection of TA. - Highlights: • Aluminium bismuthate nanorods were synthesized by a facile hydrothermal process. • The size of aluminium bismuthate nanorods could be controlled by growth conditions. • Aluminium bismuthate nanorods showed good electrochemical performance for the detection of tartaric acid. • Aluminium bismuthate nanorods modified GCE had good reproducibility and stability.

  8. Thermodynamic evaluation of nucleation as a method for selection of aluminium nitride modifications

    Science.gov (United States)

    Kudyakova, V. S.; Shishkin, R. A.; Zykov, F. M.; Zvonarev, K. V.; Chukin, A. V.; Polyakov, E. V.; Beketov, A. R.

    2018-03-01

    The Volmer and Wulf models have been used to study the process of nucleation of aluminium nitride modifications. The sizes of the critical nuclei of aluminium nitride modifications have been determined depending on the degree of supersaturation. It has been demonstrated that by varying the technological parameters of chemical vapour deposition it is possible to determine the conditions for selection of AlN modifications.

  9. Neuroprotective effect of carvedilol against aluminium induced toxicity: possible behavioral and biochemical alterations in rats.

    Science.gov (United States)

    Kumar, Anil; Prakash, Atish; Dogra, Samrita

    2011-01-01

    Aluminium, is a trace element available in the Earth's crust naturally and has a toxic potential for humans. It has been suggested as a contributing factor in the pathogenesis of Alzheimer's disease. β-Adrenoceptor blocking agents (β-blockers) have been established as therapeutics for the treatment of patients with hypertension, ischemic heart diseases, chronic heart failure, arrhythmias and glaucoma. Over the years, however, β-blockers have been associated with an incidence, albeit low, of central nervous system (CNS) side effects. In addition, noradrenergic receptors play a modulatory role in many nerve functions, including vigilance, attention, reward, learning and memory. Therefore, the present study has been designed to explore the possible role of carvedilol, an adrenergic antagonist against aluminium chloride-induced neurotoxicity in rats. Aluminium chloride (100 mg/kg) was administered daily for six weeks that significantly increased cognitive dysfunction in the Morris water maze and oxidative damage as indicated by a rise in lipid peroxidation and nitrite concentration and depleted reduced glutathione, superoxide dismutase, catalase and glutathione S-transferase activity compared to sham treatment. Chronic aluminium chloride treatment also significantly increased acetylcholinesterase activity and the aluminium concentration in brain compared to sham. Chronic administration of carvedilol (2.5 and 5 mg/kg, po) daily to rats for a period of 6 weeks significantly improved the memory performance tasks of rats in the Morris water maze test, attenuated oxidative stress (reduced lipid peroxidation, nitrite concentration and restored reduced glutathione, superoxide dismutase, catalase and glutathione S-transferase activity), decreased acetylcholinesterase activity and aluminium concentration in aluminium-treated rats compared to control rats (p aluminium chloride-induced cognitive dysfunction and oxidative damage.

  10. Formation of Composite Surface during Friction Surfacing of Steel with Aluminium

    OpenAIRE

    Janakiraman, S.; Bhat, K. Udaya

    2012-01-01

    Commercial pure aluminium was deposited on medium carbon steel using friction surfacing route. An aluminium rod was used as the consumable tool. Normal load and tool rotation speed were the variables. Under certain combinations of load and speed the deposition was continuous and uniform. The deposit consisted of Al embedded with fine particles of iron. The interface between substrate material and deposited material was smooth and relatively small. A mechanism is discussed for formation of a ...

  11. A preliminary study of dietary aluminium intake and risk of Alzheimer's disease.

    Science.gov (United States)

    Rogers, M A; Simon, D G

    1999-03-01

    epidemiological studies of Alzheimer's disease and aluminium intake have focused on aluminium in drinking water. There have been no studies investigating the relation between the disease and the consumption of foods containing large amounts of aluminium additives. to conduct a pilot study to determine whether dietary intake of aluminium additives differs in individuals with and without Alzheimer's disease. matched case-control study. Controls were matched to cases on age, gender and date of admission to the centre. Syracuse, New York, USA. 46 participants comprising 23 matched sets. residents of the Loretto Geriatric Center with and without newly-diagnosed Alzheimer's disease were selected. Next-of-kin were asked to complete information on the resident's medical history, lifestyle behaviour and dietary intake before admission to the centre. An expanded form of the Health Habits and History Questionnaire was used to determine dietary intake. Consumption of foods containing elevated levels of aluminium additives was compared between cases and controls. the crude odds ratio for daily intake of foods containing high levels of aluminium was 2.0 and, when adjusted for covariates, was 8.6 (P=0.19). Intake of pancakes, waffles, biscuits, muffins, cornbread and/or corn tortillas differed significantly (P=0.025) between cases and controls. Adjusted odds ratios were also elevated for grain product desserts, American cheese, chocolate pudding or beverages, salt and chewing gum. However, the odds ratio was not elevated for tea consumption. past consumption of foods containing large amounts of aluminium additives differed between people with Alzheimer's disease and controls, suggesting that dietary intake of aluminium may affect the risk of developing this disease. Larger studies are warranted to corroborate or refute these preliminary findings.

  12. Development of microstructure during sintering and aluminium exposure of titanium diboride ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Pettersen, Gunnar

    1997-12-31

    In the production of aluminium, much less energy need be consumed if an inert, wetted cathode is present in the electrolysis cell. Titanium diboride, TiB{sub 2}, is easily wetted and does not readily dissolve in liquid aluminium, but it degrades, probably because aluminium penetrates into it during electrolysis. This degradation is linked to impurities present in the TiB{sub 2} after sintering. This thesis studies the sintering process and how aluminium penetrates into the material. High-purity, high-density TiB{sub 2} compacts were made by hot pressing at 50 MPa in an argon atmosphere at 1790-1960 {sup o}C. Samples were made with different impurity additions. These samples were exposed to liquid aluminium at 980 {sup o}C for 24 hours. All samples were penetrated, but the amount and appearance depended on the sintering aid used. Unlike the other samples, pure TiB{sub 2} was easily penetrated by metallic aluminium because of the open porosity and microcracks of this material. Grain boundary penetration was common among the samples. Differences in penetration behaviour between grain boundaries are probably due to differences in grain boundary energy. But no relation to segregants or boundary misorientation was found. The orientation of grain boundary planes and de-wetting of thin films upon cooling may explain the observed microstructure development. The samples sintered with Ti addition suffered extensive penetration despite their high densities. The grain boundaries of these samples became faceted and contained thicker films of metallic aluminium, presumably because of increased solubility due to iron segregations. All secondary phases present in the grain junctions after sintering, except from the B{sub 4}C phase, reacted with the penetrated aluminium. This did not cause swelling and cracking, as has been suggested by other authors. 101 refs., 48 figs., 7 tabs.

  13. Overheating influence on solidification - thermal variables and microstructure formation of aluminium alloy

    OpenAIRE

    Rodrigues, JRP; Sousa, TXD; de Andrade, RB; dos Santos, RG; Mello, MDNM

    2009-01-01

    A comparative analysis of the 5052 aluminum alloy solidification process involving different overheating ranges is presented herein. Experimentally determined, the main parameters of the solidification process were affected in the overheating range and influenced the microstructure arrangement. The 5052 aluminium alloy was selected. It contains about. 3% magnesium and is used for commercial purposes. The aluminium alloy was poured into a device that allows unidirectional solidification and wa...

  14. 35S cystein chlorhydrate preparation

    International Nuclear Information System (INIS)

    Emiliozzi, R.; Pichat, P.; Herbert, M.

    1960-01-01

    35 S cystein chlorhydrate has been prepared with a quantitative yield by electrolytic reduction of 35 S cystin in hydrochloric medium on a vibrating mercury cathode. Reprint of a paper published in Bulletin de la Societe chimique de France, no. 2653, 4. quarter 1959, p. 1544-1545 [fr

  15. Development of multilayer coatings for forming dies and tools of aluminium alloy from liquid state

    International Nuclear Information System (INIS)

    Torres, E; Ugues, D; Brytan, Z; Perucca, M

    2009-01-01

    In this work, a nanocomposite (Cr,Al) x N 1-x /Si 3 N 4 coating system was deposited on H11 hot work tool steel, using the Lateral Arc Rotating Cathodes (LARC (registered) ) deposition system and modulating the chemical composition of the chromium and aluminium-silicon content. Structural characterizations were performed using scanning electron microscopy, equipped with energy dispersive spectroscopy probe, and applying x-ray diffraction, for the evaluation of phase constitution and crystallite size. In addition to the structural features, the coatings' resistance to cyclic immersions in molten aluminium alloy was evaluated. The deposited CrAlSiN coatings exhibited an fcc-Cr 1-x Al x N type structure with different aluminium contents, which directly influence hardness and wear and fatigue resistance in cyclic immersion tests. The main failure modes that occurred on the coatings' surface were soldering and thermal fatigue cracks mainly in the form of heat checks. The aluminium rich coatings were able to withstand about 15 000 cycles, whereas the decrease in the aluminium content in the coatings results in a decrease in the resistance to the immersion in molten aluminium bath. It is worthwhile to note that uncoated H11, subjected to similar testing conditions, withstood at maximum 5000 cycles.

  16. Damage Analysis of Aluminium Foam Panel Subjected to Underwater Shock Loading

    Directory of Open Access Journals (Sweden)

    Xuan He

    2017-01-01

    Full Text Available Underwater shock loading experiment device is the equipment which simulates underwater explosive shock wave through experiment. Underwater shock loading experiment device was used to conduct high-speed underwater impact on aluminium foam panel and its damage modes were studied in this paper. 3D dynamic DIC test system was used to collect and analyze real-time deformation of target board. After the experiment was completed, a numerical simulation of the series of experiment was conducted through ABAQUS finite element simulation and then a comparative analysis of the experiment was implemented. To comprehensively study damage modes of aluminium foam panel subjected to underwater shock loading, damage modes of aluminium foam panel at different shock speeds were studied. Results indicated that when a certain impact speed which could damage aluminium foam panel was reached, if the impact speed was low, aluminium foam panel would generate shear fracture at constrained boundary of flange; if the impact speed was high, aluminium foam panel would firstly generate fracture at the center and then generate shear fracture at constrained boundary of flange, and central fracture would generate three cracks.

  17. Oxidation and waste-to-energy output of aluminium waste packaging during incineration: A laboratory study.

    Science.gov (United States)

    López, Félix A; Román, Carlos Pérez; García-Díaz, Irene; Alguacil, Francisco J

    2015-09-01

    This work reports the oxidation behaviour and waste-to-energy output of different semi-rigid and flexible aluminium packagings when incinerated at 850°C in an air atmosphere enriched with 6% oxygen, in the laboratory setting. The physical properties of the different packagings were determined, including their metallic aluminium contents. The ash contents of their combustion products were determined according to standard BS ISO 1171:2010. The net calorific value, the required energy, and the calorific gain associated with each packaging type were determined following standard BS EN 13431:2004. Packagings with an aluminium lamina thickness of >50μm did not fully oxidise. During incineration, the weight-for-weight waste-to-energy output of the packagings with thick aluminium lamina was lower than that of packagings with thin lamina. The calorific gain depended on the degree of oxidation of the metallic aluminium, but was greater than zero for all the packagings studied. Waste aluminium may therefore be said to act as an energy source in municipal solid waste incineration systems. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Aluminium Foam and Magnesium Compound Casting Produced by High-Pressure Die Casting

    Directory of Open Access Journals (Sweden)

    Iban Vicario

    2016-01-01

    Full Text Available Nowadays, fuel consumption and carbon dioxide emissions are two of the main focal points in vehicle design, promoting the reduction in the weight of vehicles by using lighter materials. The aim of the work is to evaluate the influence of different aluminium foams and injection parameters in order to obtain compound castings with a compromise between the obtained properties and weight by high-pressure die cast (HPDC using aluminium foams as cores into a magnesium cast part. To evaluate the influence of the different aluminium foams and injection parameters on the final casting products quality, the type and density of the aluminium foam, metal temperature, plunger speed, and multiplication pressure have been varied within a range of suitable values. The obtained compound HPDC castings have been studied by performing visual and RX inspections, obtaining sound composite castings with aluminium foam cores. The presence of an external continuous layer on the foam surface and the correct placement of the foam to support injection conditions permit obtaining good quality parts. A HPDC processed magnesium-aluminium foam composite has been developed for a bicycle application obtaining a suitable combination of mechanical properties and, especially, a reduced weight in the demonstration part.

  19. Effects of Aluminium on Rat Brain Mitochondria Bioenergetics: an In vitro and In vivo Study.

    Science.gov (United States)

    Iglesias-González, Javier; Sánchez-Iglesias, Sofía; Beiras-Iglesias, Andrés; Méndez-Álvarez, Estefanía; Soto-Otero, Ramón

    2017-01-01

    Numerous studies have highlighted the potential of aluminium as an aetiological factor for some neurodegenerative disorders, particularly Alzheimer's disease and Parkinson's disease. Our previous studies have shown that aluminium can cause oxidative stress, reduce the activity of some antioxidant enzymes, and enhance the dopaminergic neurodegeneration induced by 6-hydroxydopamine in an experimental model of Parkinson's disease in rats. We now report a study on the effects caused by aluminium on mitochondrial bioenergetics following aluminium addition and after its chronic administration to rats. To develop our study, we used a high-resolution respirometry to test the mitochondrial respiratory capacities under the conditions of coupling, uncoupling, and non-coupling. Our study showed alterations in leakiness, a reduction in the maximum capacity of complex II-linked respiratory pathway, a decline in the respiration efficiency, and a decrease in the activities of complexes III and V in both models studied. The observed effects also included both an alteration in mitochondrial transmembrane potential and a decrease in oxidative phosphorylation capacity when relatively high concentrations of aluminium were added to the isolated mitochondria. These findings contribute to explain both the ability of aluminium to generate oxidative stress and its suggested potential to act as an etiological factor by promoting the progression of neurodegenerative disorders such as Parkinson's disease.

  20. Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

    Science.gov (United States)

    Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

    2011-01-01

    The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.