Development and fabrication of a Bi-2223 racetrack coil for generator applications

International Nuclear Information System (INIS)

Herd, K.G.; Salasoo, L.; Laskaris, E.T.; Ranze, R.A.; King, C.G.

1996-01-01

The development and fabrication of a layer-wound, epoxy-impregnated Bi-2223 high-temperature superconducting (HTS) racetrack coil which generates 40,000 ampere-turns of magnetomotive force (MMF) at 25 K is described. The coil was wound using Ag-sheathed Bi-2223 tape conductor laminated with copper foils for strength enhancement and insulated using a paper-wrap method. After epoxy impregnation, the coil was tested over a range of 16--25 K in a vacuum dewar using a closed-cycle helium refrigeration system. Descriptions of the tape lamination and insulation processing, the coil winding and impregnation, and the experimental test setup are given

Effect of epoxy impregnation on strain distribution of materials in Bi2223 superconducting coils by using synchrotron X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Jin, Xinzhe, E-mail: xinzhe.jin@riken.jp [Center for Life Science Technologies, RIKEN, Yokohama-shi, Kanagawa 230-0045 (Japan); Osamura, Kozo [Research Institute for Applied Sciences, Sakyo-ku, Kyoto 606-8202 (Japan); Machiya, Shutaro [Daido University, Minami-ku, Nagoya 457-8530 (Japan); Kajiwara, Kentaro [Japan Synchrotron Radiation Research Institute, Sayo, Hyogo 679-5198 (Japan); Shobu, Takahisa [Japan Atomic Energy Agency, Sayo, Hyogo 679-5148 (Japan); Maeda, Hideaki [Center for Life Science Technologies, RIKEN, Yokohama-shi, Kanagawa 230-0045 (Japan)

2015-11-25

Synchrotron X-rays have been used to observe strain distributions in composite materials such as superconducting wires with a thickness of less than about 2 mm. In applications that employ wound coils of superconducting wire, it is necessary to understand the strain distribution within the coiled wire. Superconducting wires such as Bi2223 and REBCO wires approximately 4–5 mm wide are commercially available. Coiled wires of this width are too thick to easily measure using conventional X-ray techniques, especially the inner strain, because the penetration depth tends to be around 2 mm. Therefore, the beam penetration must be improved, and it is known that the penetration depth of an X-ray beam depends upon the beam energy, beam intensity, measurement material, and measurement method. In this study, we used a white X-ray diffractometer at SPring-8 to develop a method of observing the strain distribution in Bi2223 superconducting coils winded by a 4.5 mm wide Bi2223 wire. We successfully observed a clear (400) peak of the Bi2223 phase by an appropriate measurement condition, and then observed the strains of each material in the Bi2223 coils with and without epoxy impregnation. This is the first time that we have obtained the strain of a Bi2223 phase in coiled wire using synchrotron X-ray diffraction. Further synchrotron-based study of superconducting coils will be useful in the development of advanced high-field magnets. The appropriate measurement method and the obtained measurement results are presented in this paper. - Highlights: • We successfully obtained clear peaks of Bi2223 phase in 4.5 mm thick coils. • The strain behaviors of materials in the coil correspond to a three turn cycle model. • A uniform strain distribution of the Bi2223 phase was obtained by epoxy impregnation.

The effect of sintering temperature on the intergranular properties and weak link behavior of Bi2223 superconductors

Directory of Open Access Journals (Sweden)

P. Kameli

2006-03-01

Full Text Available  A systematic study of the intergranular properties of (Bi,Pb2 Sr2 Ca2 Cu3 Oy (Bi2223 polycrystalline samples has been done using the electrical resistivity and AC susceptibility techniques. In this study, we have prepared a series of Bi2223 samples with different sintering temperatures. The XRD results show that by increasing the sintering temperature up to 865° c , the Bi2212 phase fraction decreases. It was found that the Bi2212 phase on the grain boundaries is likely to play the role of the weak links and consequently reduces the intergranular critical current densities.

Effect of Ag in structural, electrical and magnetic properties of Ag-sheated Bi-2223 wires

Directory of Open Access Journals (Sweden)

D Sohrabi

2009-08-01

Full Text Available  In this study, the superconducting properties of Bi-2223/Ag wires, made by the PIT method have been studied. Powder samples were prepared using conventional solid state reaction method. After calcination, samples with different Ag percent (0, 5, 10, 15, 20, and 25 prepared and sintered at 830 °C. It was shown that Ag addition has not only affected the formation of the desired Bi-2223 phase and the microstructure of these wires, but also influenced on the critical current density (JC and critical temperature.

A Monte Carlo-shear lag simulation of tensile fracture behaviour of Bi2223 filament

International Nuclear Information System (INIS)

Ochiai, S; Ishida, T; Doko, D; Morishita, K; Okuda, H; Oh, S S; Ha, D W; Hojo, M; Tanaka, M; Sugano, M; Osamura, K

2005-01-01

The damage evolution in Bi2223 filaments and its influence on critical current was described by a Monte Carlo-shear lag simulation method. The experimentally observed zigzag crack propagation across aligned Bi2223 grains under tensile strain was effectively modelled by including transverse and longitudinal failure modes for individual grains. From the simulated stress-strain curve, the survival parameter (slope of the stress-strain curve normalized with respect to the original Young's modulus) was estimated with increasing applied strain. With this parameter combined with the strain sensitivity of the critical current, the measured change of critical current of the composite tape with applied strain could be described well

Phase relations study on the melting and crystallization regions of the Bi-2223 high temperature superconductor

Directory of Open Access Journals (Sweden)

Alexander Polasek

2004-09-01

Full Text Available The melting and solidification behavior of Bi2Sr2Ca2Cu3 O10 (Bi-2223 precursors has been studied. Nominal compositions corresponding to excess of liquid, Ca2CuO3 and CuO have been investigated. Each sample was made by packing a precursor powder into a silver crucible, in order to approximately simulate the situation found in 2223 silver-sheathed tapes. The samples were partially melted and then slow-cooled, being quenched from different temperatures and analyzed through X-ray diffraction (XRD and scanning electron microscopy (SEM/EDS. The precursors decomposed peritectically during melting, forming liquid and solid phases. Very long plates with compositions falling in the vicinity of the 2223 primary phase field formed upon slow-cooling. The 2223 phase may have been formed and the results suggest that long grains of this phase might be obtained by melting and crystallization if the exact peritectic region and the optimum processing conditions are found.

Beginning point of metal to insulator transition for Bi-2223 superconducting matrix doped with Eu nanoparticles

International Nuclear Information System (INIS)

Yildirim, G.

2013-01-01

Highlights: •Standard measurements such as bulk density, ρ-T, J ct , XRD, SEM and EDX examinations for characterization of the samples. •Role of Eu inclusions on the microstructural, electrical and superconducting properties of Bi-2223 phase. •Determination of metal to insulator transition due to Eu impurities in the Bi-2223 superconducting matrix. •From the Eu content level of x = 0.5 onwards, destruction of the superconducting phases. •Constant retrogression of the microstructural and superconducting properties with the Eu individuals. -- Abstract: This comprehensive study examines the change of the microstructural, electrical and superconducting properties of the Eu doped Bi 1.8 Pb 0.4 Eu x Sr 2 Ca 2.2 Cu 3.0 O y ceramic cuprates (with x ⩽ 0.7) produced by the conventional solid state reaction method at the constant annealing temperature of 840 °C for 24 h with the aid of the standard characterization measurements such as bulk density, dc resistivity (ρ-T), transport critical current density (J c ), X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron dispersive X-ray (EDX) examinations. For the full characterization of the pure and Eu doped Bi-2223 samples, the degree of granularity (from the bulk density and porosity measurements); the room temperature resistivity, onset–offset critical transition temperature, variation of transition temperature, hole carrier concentration, spin-gap opening temperature and thermodynamic fluctuations (from the dc resistivity experiments); the texturing, crystal structure, crystallite size, phase purity and cell parameters (from the XRD investigations); the variation of the flux pinning centers and the boundary weak-links between the superconducting grains (from the critical current density values); the crystallinity, specimen surface morphology, grain connectivity between the superconducting grains and grain size distribution (from the SEM examinations), the elemental compositions and

Simulation of transport critical current of Bi2223/Ag tape with ferromagnetic shielding

International Nuclear Information System (INIS)

Gu, C.; Alamgir, A.K.M.; Qu, T.M.; Han, Z.

2008-01-01

Ferromagnetic shielding (FS) was coated onto the surface of the Bi2223/Ag multi-filamentary tape. Transport critical current of the Bi2223/Ag multi-filamentary tape with a FS was systematically studied by numerical simulation. In the help of a finite element analysis (FEA) tool, we are able to understand how the FS alters the flux inside the superconductor region and thus increases and decreases the critical current density locally. The results show the open FS function both positively and negatively to the performance of the tape. An optimization process was proposed, aiming to reach a tradeoff between I c increasing and less usage of the ferromagnetic material. Three important shielding parameters, shielding width, shielding thickness, and shielding material were taken into account

Simulation of transport critical current of Bi2223/Ag tape with ferromagnetic shielding

Energy Technology Data Exchange (ETDEWEB)

Gu, C. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China)], E-mail: guchen@tsinghua.edu.cn; Alamgir, A.K.M. [Faculty of Engineering, Yokohama National University, 75-9 Tokiwadai, Hodogaya, ku, Yokohama (Japan); Qu, T.M. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education (China); Han, Z. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China)

2008-09-15

Ferromagnetic shielding (FS) was coated onto the surface of the Bi2223/Ag multi-filamentary tape. Transport critical current of the Bi2223/Ag multi-filamentary tape with a FS was systematically studied by numerical simulation. In the help of a finite element analysis (FEA) tool, we are able to understand how the FS alters the flux inside the superconductor region and thus increases and decreases the critical current density locally. The results show the open FS function both positively and negatively to the performance of the tape. An optimization process was proposed, aiming to reach a tradeoff between I{sub c} increasing and less usage of the ferromagnetic material. Three important shielding parameters, shielding width, shielding thickness, and shielding material were taken into account.

Transport ac losses in Bi-2223 multifilamentary tapes - conductor materials aspect

Energy Technology Data Exchange (ETDEWEB)

Glowacki, B A [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge BC2 3QZ (United Kingdom); Majoros, M [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); Institute of Electrical Engineering, SAS, Bratislava (Slovakia)

2000-05-01

Transport ac losses in technical superconductors based on Bi-2223 tape material are influenced by many parameters. The major factors that define the ac performance of such conductors are the following: the size and number of filaments, their geometrical arrangement in the cross-section of the conductor, the twist pitch length, the resistivity of the matrix, the presence of oxide barriers around the filaments and deformation procedures such as sequential pressing or rolling followed by appropriate thermal treatment. In the present paper the above aspects are addressed from the viewpoint of the materials science of technical conductor design. Transport ac losses at power frequencies in different types of Bi-2223 conductor are presented and analysed. The results of conductor design analysis with respect to the coexistence of the superconductor with other materials in the conductor structure are presented. New concepts for minimization of the transport ac losses are discussed in detail. (author)

Effect of cooling rates on bare bulk and silver wrapped pellets of Bi-2223 superconductor

International Nuclear Information System (INIS)

Terzioglu, C.; Oztuerk, O.; Kilic, A.; Gencer, A.; Belenli, I.

2006-01-01

We have examined the effect of cooling rates on oxygen content of Bi-2223 phase samples with and without silver sheating. Two sets of samples with and without silver sheating were annealed under identical conditions and cooled with rates of 10 deg. C/h, 25 deg. C/h, 50 deg. C/h, 75 deg. C/h, and 100 deg. C/h. XRD examination of the samples showed that a high percentage of Bi-2223 was obtained. Microstructure examinations were performed by scanning electron microscopy. Resistive and magnetic transitions of the samples were studied. All the reported data were discussed and related

Microstructural evolution at the initial stages of annealing in a Bi-2223 multifilament tape

DEFF Research Database (Denmark)

Liu, Y.L.; Grivel, J.-C.; Wang, W.G.

2001-01-01

The microstructural evolution at the initial stage of annealing in a multifilament Bi-2223 (2223) tape is studied in quenched samples using XRD, SEM and EDS. The annealing was carried out at 830 degreesC under reduced oxygen partial pressure. Samples were quenched in air upon reaching 830 degrees...... and the size (measured in tape plane) is comparable with the particle spacing indicating a liquid activity on an overall scale and sufficient feeding of Cu and Ca. Consequently, the 2223 develops at a fast rate. After 10 li the liquid amount is decreased, the particle spacing is far larger than the liquid size...

Measuring the homogeneity of Bi(2223)/Ag tapes by four-probe method and a Hall probe array

International Nuclear Information System (INIS)

Kovac, P.

1999-01-01

The nature of the BSCCO compound and application of the powder-in-tube technique usually lead to non-uniform quality across and/or along the ceramic fibres and finally to variations in the critical current and its irregular distribution in the Bi(2223)/Ag tape. Therefore, the gliding four-probe method and contactless field monitoring measurements have been used for homogeneity studies. The gliding potential contacts moved along the tape surface and a sensitive system based on an integrated Hall probe array containing 16 or 19 in-line probes supported by PC-compatible electronics with software allowed us to make a comparison of contact and contactless measurements at any elements of Bi(2223)/Ag sample. The results of both methods show very good correlation and the possibility of using a sensitive Hall probe array for monitoring the final quality of Bi(2223)/Ag tapes. (author)

Development of high J c Bi2223/Ag thick film materials prepared by heat treatment under low P O2

Science.gov (United States)

Takeda, Y.; Shimoyama, J.; Motoki, T.; Nakamura, S.; Nakashima, T.; Kobayashi, S.; Kato, T.

2018-07-01

In general, a dense and c-axis grain-oriented microstructure is desirable in order to achieve the high critical current properties of Bi2223 polycrystalline materials. On the other hand, our recent studies have shown that precise control of the chemical compositions of Bi2223 is also effective for the enhancement of intergrain J c. In this study, the development of Bi2223 thick film materials with high critical current properties was attempted by controlling both the microstructure and the chemical compositions. A high intergrain J c of ∼8 kA cm‑2 at 77 K of a film with ∼40 μm t was achieved by increasing the Pb substitution level for the Bi site and controlling the nonstoichiometric chemical compositions. Furthermore, it was revealed that an increase in the thickness enabled us to obtain high I c films suitable for practical applications. In contrast, there are still issues, especially in controlling the grain alignment at the inner part of the film, which suggests that the J c properties of thick film materials could be further improved by forming a more ideal microstructure, as realized in the Bi2223 filaments of multi-filamentary Ag-sheathed tapes.

Comparison of bending strain effect on the critical current degradation of Bi-2223 tapes through different measurement techniques

International Nuclear Information System (INIS)

Shin, Hyung-Seop; Dizon, John R.C.; Katagiri, Kazumune; Kuroda, Tsuneo

2006-01-01

Unlike in the tests under tension, transverse compression and torsion, the bending test of HTS tapes requires lots of time and effort since the sample should be bent or mounted successively onto sample holders having different bending radius at room temperature, and then cooled down to measure the critical current, I c , up to 77 K at each step. In this process, the effect of repeated thermal cycle on the I c degradation can not be ignored. The establishment of a practical and effective measurement method of the critical current as a function of bending strain for HTS tapes should be considered. A ρ-shaped sample holder which provides a series of bending strains to HTS tapes was newly devised. In this case, the connection of Bi-2223 tapes to current terminal blocks was done mechanically. Using this sample holder, the bending strain effect on the I c degradation behavior in Bi-2223 tapes in the easy bending mode was investigated, and discussed them comparing with other data obtained by different testing methods, namely, the conventional bending method using FRP sample holders and the Goldacker-type continuous bending test rig. Commercially available Bi-2223 tapes which have different reinforcing structures were supplied for this study. By using the newly devised ρ-shaped sample holder, it was possible to obtain a bending strain characteristic of I c in Bi-2223 tapes at one time cooling which lessened the testing time significantly when compared with other testing methods and supply good reproducible data. The I c degradation behavior in Bi-2223 tapes was similar to the cases using FRP sample holders although it showed slightly higher I c values

Ultrasonic studies of aluminium-substituted Bi(Pb)-2223 superconductors

Science.gov (United States)

Solunke, M. B.; Sharma, P. U.; Pandya, M. P.; Lakhani, V. K.; Modi, K. B.; Venugopal Reddy, P.; Shah, S. S.

2005-09-01

The compositional dependence of elastic properties of Al^{3+}-substitu- ted Bi(Pb)-2223 superconducting system with the general formula Bi_{1.7-x}Al_xPb_{0.3}Sr_2Ca_2- Cu_3O_y (x = 0.0, 0.1, 0.2 and 0.3) have been studied by means of ultrasonic pulse transmission (UPT) technique at 1 MHz (300 K). The elastic moduli of the specimens are computed and corrected to zero porosity. The observed variation of elastic constants with aluminium substitution has been explained on the basis of the strength of interatomic bonding. The applicability of heterogeneous metal mixture rule for estimating elastic constants and transition temperature has been tested.

Strain reduced critical current in Bi-2223/Ag superconductors under axial tension and compression

International Nuclear Information System (INIS)

Haken, B. ten; Godeke, A.; Kate, H.H.J. ten

1997-01-01

The critical current of Ag sheathed Bi(Pb)SrCaCuO-2223 tape conductors is investigated as a function of various strain components. A reduction of the critical current occurs due to both tensile or a compressive strain. The critical current reduction is qualitatively similar with the results as observed in Bi-2212 conductors. An axial compression leads to an immediate critical current reduction. The critical current in an axially elongated sample remains nearly constant up to a certain limit typically close to 0.3% strain. For a larger elongation the critical current reduces rapidly. A transverse pressure acting on the tape surface leads also to an irreversible critical current reduction. This behavior is compared with the influence of an axial compression with an effective Young's modulus. The deformation induced critical current reductions in Bi-2223 conductors can be described by a model that is already proposed for Bi-2212 conductors. This model is based on the irreversible nature of the critical current reduction due to a certain deformation

Comparative study on the critical current performance of Bi-2223/Ag and YBCO wires in low magnetic fields at liquid nitrogen temperature

International Nuclear Information System (INIS)

Feng, F.; Qu, T.-M.; Gu, C.; Xin, Y.; Gong, W.-Z.; Wu, W.; Han, Z.

2011-01-01

Highlights: → The I c values of Bi-2223/Ag and YBCO wires in low fields at 77 K were compared. → The performance of Bi-2223/Ag in low parallel fields was better than that of YBCO. → The phenomenon mentioned above can be verified by the published literature datum. → A new aspect was brought to understand the transport properties of HTS wires. - Abstract: A comparative study on the critical current performance of Bi-2223/Ag and YBCO coated conductor wires in low magnetic fields at liquid nitrogen temperature was carried out in this work. Five commercial high temperature superconductor wires from different manufacturers were collected. Their critical currents were measured in magnetic fields, ranging from 0 to 0.4 T. On contrary to the common conception, the Bi-2223/Ag samples had better performance than YBCO coated conductor samples in the magnetic fields parallel to the wide surface of superconducting wires within the experimental scope. We also found similar results by collecting the concerned datum from the published literatures to confirm our measurement results. At the present stage, this fact made that the Bi-2223/Ag wires might be the preferred choice for the applications with mainly low parallel fields involved, unless other considerations were prioritized.

Progress in Jc and magnetic field performance of Bi-2223/Ag composite tapes

International Nuclear Information System (INIS)

Savvides, N.; Katsaros, A.; Reilly, D.; Thorley, A.; Herrmann, J.

1998-01-01

Full text: The application of high-temperature superconductors to electric power systems is actively pursued by several commercial teams around the world. A promising candidate is the Bi-2223/Ag composite superconductor. For large scale commercial applications the conductor must meet certain engineering specifications including high current capacity in the presence of a self-generated magnetic field ranging from a few hundred mT in transmission cables to 1-2 T in transformers and current limiters, and to much higher fields in the case of superconducting coils for energy storage and magnets. In the last two years, a commercial consortium consisting of Metal Manufactures Ltd, University of Wollongong and CSIRO has focused on the development of Bi-2223/Ag composite tape suitable for use in electric power applications. The powder-in-tube process is used to produce conventional single filament and multifilament tapes and twisted conductors. An appropriate measure of 'process capability' is routine running of the process and evaluation of tape performance. In this paper we report on the electrical properties of Bi-2223/Ag composite tapes produced as part of the long-length product development. The transport critical current density of tapes is measured in magnetic fields up to 9 T (H parallel and H perpendicular tape-plane) and as a function of temperature (4 - 80 K). Transport ac losses are determined at 77 K and 60 Hz, and the bend strain performance is determined at 77 K for strains up to 1.5 %

Magnetic and structural properties of Bi(2223doped by pb and Sb

Directory of Open Access Journals (Sweden)

H. Salamati

1998-04-01

Full Text Available   In a systematic approach, we have investigated the effect of the presence of Pb and Sb in the Bi site in a BSCCO (2223 phase superconductor. There are some contradictory reports in substitution of Sb in the Bi site. Some researchers report an increase in the Tc of these materials. So, we have made an accurate stoichiometry of these superconductors and selected extra pure starting materials with appropriate ratios of Pb+Sb.   The susceptility of these samples have been measured and the structures of the systems have been studied by SEM and XRD. The results of this investigation show that, Although the presence of Pb is essential for formation of (2223 phase, but addition of small amount of Sb helps to stabilize and enhance the ratio of higher phase. Our results show that, presence of Sb would raise the critical current density, but would not affect the Tc of these superconductors.

Induced critical current density limit of Ag sheathed Bi-2223 tape conductor

International Nuclear Information System (INIS)

Ogiwara, H.; Satou, M.; Yamada, Y.; Kitamura, T.; Hasegawa, T.

1994-01-01

The authors have already reported the best critical current density of 66,000 A/cm 2 with an Ag sheathed Bi-2223 tape conductor. The Brick-wall model is for explaining the current transport mechanism of this conductor. The model has its roots in the fact that the Bi-2223 tape core is a complicated stack of crystals which have a mica-flake structure. The orientation of the crystals which have a mica-flake structure. The orientation of the crystals seriously affects the current transport capability. Moreover, the contacts between the stacking crystals are very important. The transport current flows dividing into many branch paths. Under high magnetic field, the different paths experienced different electromagnetic forces. Differences between the electromagnetic forces on the different crystals can affect the contacts so as to increase resistivity and decrease overall critical current density of the tape. This effect can foretell the limit of the critical current density obtainable with these kinds of conductors

Bending strain study of Bi-2223/Ag tapes using Hall sensor magnetometry

International Nuclear Information System (INIS)

Lahtinen, M.; Paasi, J.; Sarkaniemi, J.; Han, Z.; Freltoft, T.

1996-01-01

The influence of room temperature bending on critical current (I c ) of Bi-2223/Ag tapes is studied by Hall sensor magnetometry, four-point method and scanning electron microscopy. Hall sensor magnetometry allows one to assess tape homogeneity and the amount of mechanical damage caused by bending. The microstructure of the Bi-2223 ceramic is found to strongly affect the tape behavior under bending strain. In a tape with moderate I c = 6.1 A at 77 K and a porous ceramic core, crack propagation took place normal to the Ag-ceramic interface, whereas in tapes with dense core, I c above 10 A at 77 K, cracks propagated in the tape plane. In monofilamentary tapes core homogeneity correlated with good bending strain performance. In multifilamentary tapes crack propagation between filaments was prohibited by the Ag matrix, thus leading to enhanced strain tolerance. In the high I c tapes studied, bending to 25 mm radius resulted in 1%--2% I c degradation

Synthesis and characterization of PbO-CdO nanocomposite and its effect on (Bi,Pb)-2223 superconductor

Energy Technology Data Exchange (ETDEWEB)

Yahya, Nabil A.A. [Thamar University, Physics Department, Faculty of Education, Thamar (Yemen); Al-Gaashani, R. [Thamar University, Physics Department, Faculty of Education, Thamar (Yemen); Qatar Environment and Energy Research Institute (QEERI), Hamad Bin Khalifa University (HBKU), Doha (Qatar); Abd-Shukor, R. [Universiti Kebangsaan Malaysia, School of Applied Physics, Bangi, Selangor (Malaysia)

2017-03-15

A PbO-CdO nanocomposite-added Bi{sub 1.6}Pb{sub 0.4}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} ((Bi,Pb)-2223) superconductor has been prepared. The effect of the PbO-CdO nanocomposite addition on the transport critical current density (J{sub c}) of (Bi,Pb)-2223 superconductor was investigated. The transition temperature (T{sub c-onset}), zero electrical resistance temperature (T{sub c-R=0}), and J{sub c} of the samples were measured by the four-probe method. Phase formation, structure, and microstructure of samples were investigated. The distribution of nanoparticle size was determined. The results indicated that the PbO-CdO-added samples showed larger grain size and an increased volume fraction of high-T{sub c} phase (Bi-2223) compared to the non-added sample. A slight increase in T{sub c-R=0} of x = 0.15 wt% was observed. J{sub c} of the PbO-CdO nanocomposite-added samples was significantly higher than for the non-added sample. That could be explained by the possibility that the PbO-CdO nanocomposite acts as an effective flux pinning center in (Bi,Pb)-2223. At 77 K, J{sub c} of x = 0.15 wt% added sample was more than 20 times larger than J{sub c} of the non-added sample (x = 0 wt%). A combined effect of enhanced flux pinning, increased fraction of high-T{sub c} phase and improved grain size, which led to increase in the J{sub c} of added samples, is discussed. (orig.)

Applied rolling and sensitivity of Bi(2223)/Ag tapes on Ic degradation by mechanical stress

International Nuclear Information System (INIS)

Kovac, P.; Bukva, P.; Husek, I.; Richens, P.E.; Jones, H.

1999-01-01

An experimental study of multicore Bi(2223)/Ag tapes, roll-sintered by different methods and subjected to bending and tension stresses has been performed. The tapes, of various technological histories, were bent and tensioned and subsequently the transport current was measured at each stressed state. Comparison of I c degradation curves shows that applied rolling may influence the sensitivity of Bi-2223 filaments against the mechanical stress. The existence of transverse microcracks caused by intermediate rolling leads to a higher sensitivity of the tape to bending. A lowering of critical current degradation was observed for two-axially rolled tapes having a higher filament density and better homogeneity prior to sintering treatment. (author)

Experiment of enhancing critical current in Bi-2223/Ag tape by means of ferromagnetic shielding

Energy Technology Data Exchange (ETDEWEB)

Alamgir, A.K.M. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China)]. E-mail: alam643@hotmail.com; Gu, C. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China); Han, Z. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China)

2005-11-15

Critical current in multifilamentary Ag-sheath Bi-2223 tape is enhanced to some extent by means of thin and narrow coating of pure nickel. The concept of enhancing critical current is based on the magnetic shielding effect resulting in redirection of self-field flux lines. The Ni coating was introduced at the edge regime of the tape in order to redirect the perpendicular component of self-field lines which is severe at the edges. Critical current in a typical Ag-sheath Bi-2223 tape was enhanced up to {approx}11% by 50 {mu}m thick and 0.4 mm long Ni coating without any change of self-field loss. This fact reveals that additional ferromagnetic loss could be compensated by the shielding effect and increased critical current of the tape. The degree of enhancement in critical current as well as ferromagnetic impact on ac losses depend on the length and thickness of ferromagnetic coating introduced. Therefore, it is very important to control the geometry of ferromagnetic coating in order to balance the critical current and ac loss for optimum superconductor performance. Introduction of ferromagnetic coating and its effect on electromagnetic properties in multifilamentary Bi-2223/Ag tape will be reported in this article.

Experiment of enhancing critical current in Bi-2223/Ag tape by means of ferromagnetic shielding

International Nuclear Information System (INIS)

Alamgir, A.K.M.; Gu, C.; Han, Z.

2005-01-01

Critical current in multifilamentary Ag-sheath Bi-2223 tape is enhanced to some extent by means of thin and narrow coating of pure nickel. The concept of enhancing critical current is based on the magnetic shielding effect resulting in redirection of self-field flux lines. The Ni coating was introduced at the edge regime of the tape in order to redirect the perpendicular component of self-field lines which is severe at the edges. Critical current in a typical Ag-sheath Bi-2223 tape was enhanced up to ∼11% by 50 μm thick and 0.4 mm long Ni coating without any change of self-field loss. This fact reveals that additional ferromagnetic loss could be compensated by the shielding effect and increased critical current of the tape. The degree of enhancement in critical current as well as ferromagnetic impact on ac losses depend on the length and thickness of ferromagnetic coating introduced. Therefore, it is very important to control the geometry of ferromagnetic coating in order to balance the critical current and ac loss for optimum superconductor performance. Introduction of ferromagnetic coating and its effect on electromagnetic properties in multifilamentary Bi-2223/Ag tape will be reported in this article

Fabrication and properties of Ag-Bi2223 tapes with resistive barriers for filament decoupling

International Nuclear Information System (INIS)

Inada, Ryoji; Fukumoto, Yohei; Yasunami, Taeko; Nakamura, Yuichi; Oota, Akio; Li Chengshang; Zhang Pingxiang

2007-01-01

In this paper, we prepared the Bi2223 multifilamentary tapes with Ca 2 CuO 3 + Bi2212 as interfilamentary resistive barriers to suppress the electromagnetic coupling among the filaments under AC external magnetic field. The tapes with thin barrier layers of Ca 2 CuO 3 + 30 wt% Bi2212 around the filaments were prepared by using a standard powder-in-tube (PIT) method. The outside surface of monocore Ag-sheathed rods was coated by barrier materials. Then, the several coated monocore wires were stacked and packed into another Ag or Ag-Mg alloy tube. The packed tube was drawn and rolled into tape shape. The tape was subsequently sintered to form Bi2223 phase inside filaments. For the characterization of tapes, X-ray diffraction measurements were performed to investigate the phase formation inside the filaments. The uniformity of transport properties (J c ) for barrier tapes were evaluated on the order of several metre lengths and compared with the result for the tapes without barriers. Finally, AC loss characteristics under AC parallel transverse magnetic field were investigated to examine the effect of introducing the barriers on the filament decoupling

Comparison of growth texture in round Bi2212 and flat Bi2223 wires and its relation to high critical current density development

OpenAIRE

Kametani, F.; Jiang, J.; Matras, M.; Abraimov, D.; Hellstrom, E. E.; Larbalestier, D. C.

2015-01-01

Why Bi2Sr2CaCu2Ox (Bi2212) allows high critical current density Jc in round wires rather than only in the anisotropic tape form demanded by all other high temperature superconductors is important for future magnet applications. Here we compare the local texture of state-of-the-art Bi2212 and Bi2223 ((Bi,Pb)2Sr2Ca2Cu3O10), finding that round wire Bi2212 generates a dominant a-axis growth texture that also enforces a local biaxial texture (FWHM

Effect of lead content on phase evolution and microstructural development in Ag-clad Bi-2223 composite conductors

International Nuclear Information System (INIS)

Merchant, N.N.; Maroni, V.A.; Fischer, A.K.; Dorris, S.E.; Zhong, W.; Ashcom, N.

1997-02-01

A two powder process was used to prepare silver-sheathed monofilamentary Bi 1.8 Pb x Sr 1.98 Ca 1.97 Cu 3.08 O y (Bi-2223) tapes with varying lead contents, x, from 0.2 to 0.5. The resulting tapes were subjected to thermomechanical processing and then characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray analysis (EDX). Layered phase texture was accessed using image analysis software on scanned SEM micrographs. Transport currents were measured at 77 K and zero field by the four-probe method. It was found that tapes with low lead content (X = 0.2 and 0.25) showed incomplete conversion to Bi-2223, had small grain size and poor c-axis texture. Tapes having higher lead content (x = 0.4 and 0.5) also showed incomplete conversion and the presence of lead-rich secondary phases. Tapes with lead content x = 0.3 and 0.35 showed complete conversion to Bi-2223, and had the least amount of secondary phases, the best c-axis texture, and the highest transport current (j c ). The carbon content of the precursor powder also had a strong influence on secondary-phase chemistry

Grain dynamics in Bi-2223 tapes measured by the 3DXRD microscope

DEFF Research Database (Denmark)

Poulsen, H.F.; Andersen, N.H.; Andersen, L.G.

2002-01-01

It is demonstrated how a novel X-ray diffraction method can provide information on the structural dynamics of the individual grains inside a Bi-222-3/Ag tape. A microfocused beam of 80 keV X-rays provides both the necessary spatial resolution and penetration power for in situ studies. In a feasib...

Preparation of (Bi, Pb)-2223/Ag tapes by high temperature sintering and post-annealing process

DEFF Research Database (Denmark)

Hua, L.; Grivel, Jean-Claude; Andersen, L.G.

2002-01-01

A novel heat treatment process was developed to fabricate (Bi, Pb)-2223/Ag tapes with high critical current density (J(c)). The process can be divided into two parts: reformation and post-annealing. Tapes were first heated to the maximum temperature (830-860 degreesC) followed by slow cooling...... (reformation). Then, tape, were annealed between 760 and 820 degreesC (post-annealing). Reformation is expected to produce a large amount of liquid phase which may heat microcracks, decrease porosity, and improve grain growth. However, since the sintering temperature is beyond the Bi-2223 single-phase region......-energy synchrotron XRD and SEM/EDX. Some process parameters e.g. sintering temperature. cooling rate. and post-annealing time were optimised. (C) 2002 Elsevier Science B.V. All rights reserved....

The Effect of Temperature Dependence of AC Losses in a Bi-2223/Ag Insert of an 8-T Superconducting Magnet

DEFF Research Database (Denmark)

Wang, Lei; Wang, Qiuliang; Wang, Hui

2016-01-01

A conduction-cooled split-gap superconducting magnet system with a center field of 8 T has been designed and fabricated in the Institute of Electrical Engineering, Chinese Academy of Sciences. The system consists of two Bi-2223/Ag coils and six NbTi coils. Due to a large aspect ratio of the high-...... in the second case. Hence, it is a good way to reduce the ac losses by changing the charging sequences of the Bi-2223/Ag and NbTi cols. Afterward, the calculated results are compared with the experimental data, and they show a good agreement.......A conduction-cooled split-gap superconducting magnet system with a center field of 8 T has been designed and fabricated in the Institute of Electrical Engineering, Chinese Academy of Sciences. The system consists of two Bi-2223/Ag coils and six NbTi coils. Due to a large aspect ratio of the high......-temperature superconducting tape, there will be large ac losses when the magnet is ramped up and down. An accurate estimation of the total ac losses in the high-temperature superconducting coils is essential for the cryogenic system design. In the Bi-2223/Ag coils, the total ac losses mainly originate from two parts: One...

Estabilidad y funcionalidad de sellantes dentales en altas temperaturas ambientales

OpenAIRE

Mishina, Anastasia; Mayelín Guerra, Rosa; Durán Ramos, Ivette; Sabatier, Juan D.

2000-01-01

Los sellantes dentales son materiales que se emplean en estomatología para sellar las fosas y fisuras oclusales de los dientes y evitar la adherencia del estreptococus mutans agente que produce la caries dental. Estos materiales se suministran en dos partes que al mezclarse producen el endurecimiento de la resina. Sin embargo, estos productos presentan dificultades para su comercialización en los países tropicales, debido a que las altas temperaturas ambientales traen problemas en...

Preparation and characterization of Bi-2223 tapes

International Nuclear Information System (INIS)

Hense, K.; Kirchmayr, H.; Kovac, P.; Lackner, R.; Mueller, M.; Pachla, W.; Pitel, J.; Polak, M.; Usak, P.

2003-01-01

In a concerted action between Austrian, Slovakian and Polish research institutes Bi-2223 tapes have been prepared and characterized by different physical methods. Metallographic studies by optical as well as electron microscopy, measurements of critical current (angle dependent) and losses have been performed. Properties of individual filaments extracted from multifilamentary tapes were also studied. Uniformity of local I C of these filaments were considerably lower than that of the whole tape. This indicates that improvement of filament homogeneity could improve the over all J C in tapes. The application of these tapes for optimized magnet coils will also be discussed. From these investigations a better understanding of the mechanisms, limiting the critical current could be achieved and more optimized preparation methods can be envisioned

Uranium doping and neutron irradiation of Bi-2223 superconduction tapes for improved critical current density

International Nuclear Information System (INIS)

Moss, S.D.; Wang, W.G.; Dou, S.X.; Weinstein, R.

1998-01-01

It is demonstrated that a combination of neutron irradiation with uranium doping introduce fission tracks through a Bi-2223 tape which act as effective pinning centres, leading to a substantial increase in critical current. Preliminary data suggests that the combination of uranium doping and neutron irradiation produces improved flux pinning in Bi-2223 tapes over neutron irradiation alone. Before irradiation, SEM, DTA and XRD analyses were performed on the tapes. Both before and after irradiation the trapped maximum magnetic flux was measured at 77K. Before neutron irradiation, uranium doping has no effect on critical current. Preliminary SEM data suggested that the uranium is homogeneously distributed throughout the oxide core of the tape. The presence of 2212 and other secondary phases in the doped tapes suggest further refinement of the sintering procedure is necessary. (authors)

Enhancement of critical currents in bulk and Ag-sheathed Bi(Pb)-2223 superconductors

International Nuclear Information System (INIS)

Brauer, D.J.; Eujen, R.; Hudepohl, J.

1991-01-01

This paper reports on the superconducting properties of the Bi(Pb)-2223 phase that have been optimized. Prolonged annealing of coarse powder raised j c in bulk samples to as high as 1100 Acm -2 at 77 K. the temperature dependence was studied between 96 and 4.2 K whereby j c rose gradually from 120 to 2100 Acm -2 . T c dropped from 107 K to 64 K in magnetic fields up to 4 T but decreased by only 1 K/T in higher fields. A tape prepared by rolling and subsequent annealing of Ag tubes containing Bi(Pb)-2223 powder exhibited a j c of 1700 Acm -2 at 77 K and 11000 Acm -2 at 4.2 K. The latter j c dropped to 3000 Acm -2 in a magnetic field of 0.25 t, but it was still 1200 Acm -2 in a 10 T field. A tape fabricated by pressing a drawn and annealed wire proved to be less sensitive to low magnetic fields

Un proyecto europeo en metrología de altas temperaturas para aplicaciones industriales

Directory of Open Access Journals (Sweden)

del Campo, D.

2013-08-01

Full Text Available The measurement of temperatures above 1000 ºC is both difficult and yet vital for the success of a wide range of industrial processes; glass and ceramic manufacturing (1100 ºC to 2000 ºC or refractory metals production (2500+ ºC are clear examples. Many of these industries require improved process efficiency/control, because of growing environmental concerns (emissions/”zero waste” and competition from outside the EU. One of the keys to making advances to these drivers is improving process control by improved high temperature measurement. In the frame of the European Metrology Research Program (EMRP, a project named “High temperature metrology for industrial applications (HiTeMS with the overall objective of developing a suite of methods and techniques for improving the measurement of high temperatures in industry has been running since September 2011. This paper gives an overview of the main objectives of the project and the technical activities that are being performed.La medida de temperatura por encima de 1000 ºC es tanto complicada como vital para el éxito de una gran variedad de procesos industriales; la producción de cerámica y vidrio (de 1100 ºC a 2000 ºC o de materiales refractarios (temperaturas por encima de 2500 ºC, son claros ejemplos. Muchas de estas industrias requieren una mejora de la eficiencia y del control de sus procesos debido a la creciente preocupación por el medio ambiente (“cero emisiones” y la competencia de países fuera de la Unión Europea. Una de las claves para llevar a cabo avances en este sentido es mediante la mejora del control de los procesos mejorando la medida de alta temperatura. Dentro del Programa Europeo de Investigación en Metrología (EMRP en sus siglas en inglés se está desarrollando, desde septiembre de 2011, un proyecto llamado “Metrología de altas temperaturas para aplicaciones industriales” (HiTeMs, con el objetivo fundamental de desarrollar una serie de m

Positron lifetime studies of 100-MeV oxygen irradiated Pb-doped Bi-2223 superconductors

NARCIS (Netherlands)

Banerjee, T.; Viswanath, R.N.; Kanjilal, D.; Kumar, R.; Ramasamy, S.

2000-01-01

Positron lifetime studies have been carried out for unirradiated and 100-MeV oxygen ion irradiated Pb-doped Bi-2223 superconductors. The analysis of positron lifetime spectra revealed three lifetime components: a short lifetime, τ1 = 153–196 ps; an intermediate lifetime, τ2 = 269–339 ps; and a long

Current Capacity of Ag/Bi-2223 Wires for Rotating Electric Machinery

International Nuclear Information System (INIS)

Hussennether, Volker; Leghissa, Martino; Neumueller, Heinz-Werner

2006-01-01

With focus on the application in rotating electric machines we measured the dependence of current capacity of Ag/Bi-2223 wires on temperature and magnetic field. Even for wires stemming from a single manufacturer we observe a significant spread of wire properties. We study different temperature and magnetic field dependence by a parallel path model which allows for a quantitative analysis. The implications of experiments and modelling are discussed with regard to the further wire development and for application within windings

AC losses in Ag-sheathed Bi2223 tapes with Ca2CuO3 as interfilamentary resistive barriers

International Nuclear Information System (INIS)

Inada, R.; Iwata, Y.; Tateyama, K.; Nakamura, Y.; Oota, A.; Zhang, P.X.

2006-01-01

In this study, we prepared the Bi2223 multifilamentary tapes with Ca 2 CuO 3 as interfilamentary resistive barriers and evaluated their AC magnetization loss properties at 77 K. The Bi2223 tapes with thin barrier layers of Ca 2 CuO 3 around the filaments were prepared by using a standard powder-in-tube (PIT) method. To fabricate the Ca 2 CuO 3 layers around each filament, the outside surface of monocore Ag-sheathed wires was coated by Ca 2 CuO 3 with the slurry. After the heat treatment to decompose and evaporate the organic binder in the slurry, the several coated monocore wires were stacked and packed into another Ag-tube. Then, the packed tube was drawn and rolled into tape shape. The tape was subsequently sintered to form Bi2223 phase inside filaments. The AC magnetization losses in an AC transverse magnetic field were measured by a pick-up coil method. The loss properties in the barrier tape were compared with those in the tape without barriers. The results indicated that introducing Ca 2 CuO 3 barriers is very effective to suppress the electromagnetic coupling among the filaments and also to reduce the magnetization losses under parallel transverse field

The current distribution in Bi-2223/Ag HTS conductors: comparing Hall probe and magnetic knife

NARCIS (Netherlands)

Demencik, E.; Dhalle, Marc M.J.; ten Kate, Herman H.J.; Polak, M.

2006-01-01

We analyzed the current distribution in three Bi-2223/Ag tapes with different filament lay-out, comparing the results of magnetic knife and Hall probe experiments. Detailed knowledge of the current distribution can be useful for the diagnostics of HTS conductors. The lateral current distribution was

Investigation on the phase transformation of Bi-2223/Ag superconducting tapes during heating

International Nuclear Information System (INIS)

Huang, K.-T.; Qu, T.-M.; Xie, P.; Han, Z.

2013-01-01

Highlights: • In situ resistance measurement was carried out on Bi-2223/Ag superconducting tapes. • The oxygen partial pressure of the outlet gas in the heating process was monitored continuously. • The samples quenched in the heating process were studied by XRD and T c measurements. • The heating process contains three procedures: oxygen diffusion, Pb-rich phase evolution and liquid phase formation. -- Abstract: The phase transformation of Bi-2223/Ag superconducting tapes during heating was investigated. The resistance of the ceramic core as a function of the heating temperature was measured in situ. The pO 2 of the outlet gas in the heating process was also monitored continuously. By comparing the heating process with the X-ray diffraction and T c measurements taken from samples quenched at different temperatures, we have identified that the heating process could be divided into the following regions: (1) the oxygen diffusion (OD) region, which is mainly influenced by OD; (2) the Pb-rich phase evolution (PbE) region, in which the formation and decomposition of the Pb-rich phases occur; (3) the liquid phase formation (LF) region, in which resistance increased rapidly with increasing temperature

Effect of composition on the fabrication and properties of Ag-Cu alloy sheathed (Bi,Pb)2223 tapes

International Nuclear Information System (INIS)

Nakamura, Yuichi; Nakashima, Sohei; Inada, Ryoji; Oota, Akio

2004-01-01

To achieve high J c values as well as high mechanical strength, the effects of Ag-Cu alloy sheath and initial composition of precursor on the microstructure and J c properties of Ag-Cu alloy sheathed tapes were investigated. The alkaline-earth cuprate particles were found to form preferentially near the interface between superconducting core and sheath. Although the worse (Bi,Pb)2223 purity and microstructure of alloy sheathed tapes, the reduction of J c values of the tapes was small especially in 7-filaments tapes. This might be explained by the well grain alignment of (Bi,Pb)2223 into the middle region of the filament due to the high strength of alloy sheath. The usage of the Cu deficient composition was effective to reduce the total amount of 14:24 particle while the filament thickness should be thin to maintain J c values for Ag-Cu alloy sheathed tapes due to the lack of Cu diffusion from the sheath to convert 2212 into (Bi,Pb) in the middle region of the filament

Magneto-optical investigations of Ag-sheathed Bi-2223 tapes with ferromagnetic shielding

International Nuclear Information System (INIS)

Yurchenko, V.V.; Shantsev, D.V.; Galperin, Y.M.; Alamgir, A.K.M.; Han, Z.; Johansen, T.H.

2007-01-01

An increase in the critical current and suppression of AC losses in superconducting wires and tapes with soft magnetic sheath have been predicted theoretically and confirmed experimentally. In this work we present the results of magneto-optical investigations on a series of Ag-sheathed Bi-2223 tapes with Ni coating. We visualize distributions of magnetic field at increasing external field and different temperatures, demonstrating a difference between the flux propagation in the superconductor with Ni rims and a reference sample without Ni coating

Magneto-optical investigations of Ag-sheathed Bi-2223 tapes with ferromagnetic shielding

Energy Technology Data Exchange (ETDEWEB)

Yurchenko, V.V.; Shantsev, D.V.; Galperin, Y.M. [University of Oslo, Department of Physics, P.O. Box 1048, Blindern, 0316 Oslo (Norway); Alamgir, A.K.M.; Han, Z. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Beijing 100084 (China); Johansen, T.H. [University of Oslo, Department of Physics, P.O. Box 1048, Blindern, 0316 Oslo (Norway)], E-mail: tomhj@fys.uio.no

2007-09-01

An increase in the critical current and suppression of AC losses in superconducting wires and tapes with soft magnetic sheath have been predicted theoretically and confirmed experimentally. In this work we present the results of magneto-optical investigations on a series of Ag-sheathed Bi-2223 tapes with Ni coating. We visualize distributions of magnetic field at increasing external field and different temperatures, demonstrating a difference between the flux propagation in the superconductor with Ni rims and a reference sample without Ni coating.

Influence of transverse compressive stress on Ic degradation of Ag alloy sheathed Bi-2223 tapes

International Nuclear Information System (INIS)

Oh, S S; Ha, D W; Ha, H S; Park, C; Kwon, Y K; Ryu, K S; Shin, H S

2004-01-01

In order to investigate the degradation of critical current (I c ) in the Ag alloy sheathed Bi-2223 tapes due to a transverse compressive stress introduced during manufacturing and operation of the HTS systems, a sample holder consisting of the upper block made of Ti alloy and the lower support plate made of glass fibre reinforced plastic was prepared. A shorter spacing of voltage taps caused large degradation of critical current with respect to compressive stress. It was found that the extent of the I c degradation is proportional to the initial critical current density of the tapes. Through the experiment optimizing the shape of voltage terminals and the pressing load for the continuous contact type 4-probe I c measurement system, it was found that the conical shape tip with large curvature radius was effective in suppressing the I c degradation in Bi-2223 tapes during the I c measurement. A hard alloy sheath of Ag-0.6wt%Mn was found to be quite tolerant to the I c degradation against the pressing load of voltage terminals

Fluctuation Induced Conductivity Studies of 100 MeV Oxygen Ion Irradiated Pb Doped Bi-2223 Superconductors

NARCIS (Netherlands)

Banerjee, Tamalika; Kumar, Ravi; Kanjilal, D.; Ramasamy, S.

2000-01-01

We report on 100 MeV oxygen ion irradiation in Pb doped Bi-2223 superconductors. Resistivity measurements reveal that both grains as well as the grain boundaries are affected by such irradiation. An analysis of the excess conductivity has been made within the framework of Aslamazov-Larkin (AL) and

Fabricación y caracterización de cintas superconductoras de alta temperatura crítica.

Directory of Open Access Journals (Sweden)

M. López

2006-07-01

Full Text Available From the superconductor compound (Bi0,8Pb0,22Sr2 - Ca2Cu3O10+γ (BSCCO-2223, BSCCO - 2223 superconducting tapes were prepared using the oxide power-in-tube (OPIT method, using different thermal treatments. By submitting the tapes to high temperatures, high current densities relative to bulk material Jc ≈ 10 A/cm2 - 77 K and B = 0 T and high grain connectivity were obtained, which could be attributed to partial fusion of the compound. Morphology and composition of the packed material were studied by Scanning Electron Microscopy (SEM and Energy Dispersive X-ray spectroscopy (EDX respectively, observing a composition close to nominal and good grain connectivity, responsible of their electrical properties.

Mechanical and physical properties of Bi-2223 and Nb3Sn superconducting materials between 300 K and 7 K

International Nuclear Information System (INIS)

Nyilas, Arman; Osamura, Kozo; Sugano, Michinaka

2003-01-01

Within the framework of IEC/TC90-WG5 and VAMAS/TWA16, superconducting (SC) materials are investigated with respect to their mechanical properties between 300 K and 7 K. Besides the mechanical tests, physical and electrical properties are also determined for high T c SC-tapes. The mechanical tests comprised the characterization of tensile properties at ambient temperature as well as at 7 K of Nb 3 Sn-reacted strands, Bi2223 tapes, pure silver tapes, silver bars, silver alloy tapes and bare filaments extracted from Bi-2223 tapes. All these investigations are carried out using a variable temperature helium gas flow cryostat equipped with a servo hydraulic tensile machine (MTS, model 810). For the load measurements specially developed, highly sensitive cryogenic proof in situ working load cells are used. For the strain determination of the wires, a high resolution ultra-light double extensometer system with a specially developed low noise signal conditioner is used. The engineering parameters such as yield strength and elastic modulus are evaluated using the obtained data with newly developed software. For the tiny and brittle filaments load versus displacement data are obtained. A determined master line (Young's modulus versus machine compliance) established by thin 0.125 mm O wires of different pure metals is used for the Young's modulus estimation of filaments. For the 4 K electrical voltage-current measurements under magnetic fields of up to 13 T, an existing test facility is used for the high T c tapes. No dependency between applied strain up to 0.3% and the critical current under magnetic field could be observed for the selected specific Bi-2223 tapes. In addition, thermal expansion curves of Bi-2223 tapes along with pure silver and silver alloy (AgMg) are determined between 290 K and 7 K using in situ working extensometers. The coefficient of thermal expansion is evaluated by the determined thermal expansion versus temperature curve

Microstructure and superconducting properties of Bi-2223/Ag tapes fabricated in the two-step sintering process

International Nuclear Information System (INIS)

Lu, X.Y.; Nagata, A.; Sugawara, K.

2008-01-01

The microstructure and superconducting properties of Bi-2223/Ag tapes fabricated in the two-step sintering process were investigated. The tapes were then subjected to two heat treatments with an intermediate rolling. All the tapes were sintered at 835 deg. C for 24 h at initial sintering stage. A two-step sintering procedure was then used in the final sintering stage. In the first step, the tapes are sintered at 840-865 deg. C for 1 h. In the second step, they were sintered at 835 deg. C for 120 h. The results show that the first step sintering temperature has significant influence on the microstructure and the critical current density J c . The observed microstructures are consistent well with the different J c performances of the tapes first-step-sintered at different temperatures. The tape first-step-sintered at 850 deg. C, which has small secondary phases, stronger c-axis grain alignment, higher proportion of Bi-2223 phase, and no cracks, exhibits the highest J c value

A Monte Carlo simulation on critical current distribution of bent-damaged multifilamentary Bi2223 composite tape

International Nuclear Information System (INIS)

Ochiai, S.; Okuda, H.; Fujimoto, M.; Shin, J.K.; Oh, S.S.; Ha, D.W.

2011-01-01

We simulate critical current distribution of bent-damaged Bi2223 composite tape. We use a Monte Carlo method and a damage evolution model for simulation. With the present simulation approach, experimental results are described well. Critical current distribution stems mainly from difference in damage evolution. It was attempted to reproduce the measured critical current (I c ) distributions of the Bi2223 composite tape bent by 0-0.833% by simulation. Simulation was carried out with a Monte Carlo method in combination with a model that correlates the critical current to damage evolution. Two variables that differ from specimen to specimen were input in the simulation. One was the damage strain parameter, with which the difference in extent of damage among specimens was expressed. Another was the original critical current (I c0 ) values at zero bending strain. With the present simulation approach, the measured distributions of critical current at various bending strains, and the measured variations of average and coefficient of variation of critical current values with increasing bending strain were reproduced well.

Large and high-quality single-crystal growth of cuprate superconductor Bi-2223 using the traveling-solvent floating-zone (TSFZ) method

Science.gov (United States)

Adachi, Shintaro; Usui, Tomohiro; Kosugi, Kenta; Sasaki, Nae; Sato, Kentaro; Fujita, Masaki; Yamada, Kazuyoshi; Fujii, Takenori; Watanabe, Takao

In high superconducting transition temperature (high-Tc) cuprates, it is empirically known that Tc increases on increasing the number of CuO2 planes in a unit cell n from 1 to 3. Bi-family cuprates are ideal for investigating the microscopic mechanism involved. However, it is difficult to grow tri-layered Bi-2223, probably owing to its narrow crystallization field. Here, we report improved crystal growth of this compound using the TSFZ method under conditions slightly different from those in an earlier report [J. Cryst. Growth 223, 175 (2001)]. A Bi-rich feed-rod composition of Bi2.2Sr1.9Ca2Cu3Oy and a slightly oxygen-reduced atmosphere (mixed gas flow of O2 (10%) and Ar (90%)) were adopted for the crystal growth. In addition, to increase the supersaturation of the melts, we applied a large temperature gradient along the solid-liquid interface by shielding a high-angle light beam using Al foil around the quartz tube. In this way, we succeeded in preparing large (2 × 2 × 0 . 05 mm3) and high-quality (almost 100% pure) Bi-2223 single crystals. Hirosaki University Grant for Exploratory Research by Young Scientists and Newly-appointed Scientists.

Test results for a Bi-2223 HTS racetrack coil for generator applications

International Nuclear Information System (INIS)

Salasoo, L.; Herd, K.G.; Laskaris, E.T.; Hart, H.R. Jr.; Chari, M.V.K.

1996-01-01

Testing, results and analysis of a Bi-2223 model superconducting generator coil produced under the DOE Superconductivity Partnership Initiative are presented. The test arrangement enables coil energization with dc and transient currents over a range of operating temperatures to explore coil performance under conditions analogous to those that would be experienced by a superconducting generator field coil. Analytical calculations of coil ac and ohmic losses and temperature rise compare well with experimental measurements. Good performance is predicted for a typical 3-phase fault condition. Coil steady state and transient performance can be predicted with confidence for full scale superconductor application

Study of effect of sintering time on the 2223 phase growth Bi-Pb-Sr-Ca-Cu-O superconductor by Rietveld method

International Nuclear Information System (INIS)

Parikin; Prasuad, W; Gunawan

1996-01-01

It has been reported that the sintering time is as important for the preparation of superconductor as the sintering temperature and method. This paper reports on the finding of the optimum sintering time in the preparation of the 2223 phase bismuth (Bi) superconductor. The samples were synthesized with nominal composition 1.84 : 0.34 : 1.91 : 2.03 : 3.06 from raw materials by solid state reaction and sintered at 860 o C for five days. The resintering were done three times, i.e. 24, 48 and 96 hours. The Rietveld analysis shows that the 2223 phase grows continuously as a function of the sintering time. The highest percentage of the 2223 phase (80.64%) were obtained at 96 hours sintering time. The result suggests that the 2223 phase can be obtained effectively by sintering with sufficiently long time

Fabrication, properties, and microstructures of high Tc tapes and coils made from Ag-clad Bi-2223 superconductors

International Nuclear Information System (INIS)

Balachandran, U.; Iyer, A.N.; Youngdahl, C.A.; Motowidlo, L.R.; Hoehn, J.G.; Haldar, P.

1993-07-01

Bi-2223 precursor powders were prepared via a solid-state reaction using carbonates and oxides of Bi, Pb, Sr, Ca, and Cu. Results indicate that an in-situ reaction between constituent phases with tho formation of a transient liquid that is consumed during final heat treatment, is essential to obtain increased density with greater connectivity between the 2223 grains. Relative amounts of the constituent phases were adjusted in the powder by varying the calcination conditions, and the powder was then used to fabricate Ag-clad tapes by a powder-in-tube technique. By improving process conditions, transport critical current density (J c ) values greater than 4 x 10 4 A/cm 2 at 77 K and 2 x 10 5 A/cm 2 at 4.2 and 27 K have been obtained in short tape samples. Long tapes were cut into lengths upto 10 m long and used in parallel to fabricate small superconducting pancake coils. The coils were characterized at 77, 27 and 4.2 K and results are discussed

Surface morphology and physical properties of partially melt textured Mn doped Bi-2223

Directory of Open Access Journals (Sweden)

Indu Verma

2011-09-01

Full Text Available The samples of Bi2Sr2Ca2Cu3-xMnxO10+δ (x = 0.0 to 0.30 were prepared by the standard solid-state reaction method. The phase identification characteristics of synthesized (HTSC materials were explored through powder X-ray diffractometer reveals that all the samples crystallize in orthorhombic structure with lattice parameters a = 5.4053 Å, b = 5.4110 Å and c = 37.0642 Å up to Mn concentration of x = 0.30. The critical temperature (Tc measured by standard four probe method has been found to depress from 108 K to 70 K as Mn content (x increases from 0.00 to 0.30. The effects of sintering temperature on the surface morphology of Bi2Sr2Ca2Cu3-xMnxO10+δ have also been investigated. The surface morphology investigated through scanning electron microscope and atomic force microscopy (SEM & AFM results that voids are decreasing but grains size increases as the Mn concentration increases besides, nanosphere like structures on the surface of the Mn doped Bi2Sr2Ca2Cu3-xMnxO10+δ (Bi-2223 samples.

Fenología reproductiva y tolerancia a temperaturas altas en Stenocereus queretaroensis

Directory of Open Access Journals (Sweden)

Whaleeha Gudiño

2015-07-01

Full Text Available Numerosas especies de cactáceas presentan frutos comestibles, por lo que han adquirido un papel importante dentro de la agricultura de zonas áridas y semiáridas, tanto para el comercio regional como para el internacional. Las pitayas son el tercer cultivo más importante dentro de las cactáceas después del nopal y la pitahaya. La fenología reproductiva deStenocereus queretaroensisrequiere condiciones específcas de temperatura y precipitación, así como también de la existencia de los polinizadores para asegurar la producción de frutos. Se cuantificó la producción de botones, flores abiertas y frutos de 2010 a 2012. Y se evaluó el efecto de temperaturas altas en la integridad celular de tejidos florales. Se midió la producción de néctar y la concentración de solutos a través del tiempo durante la antesis. La temperatura letal (LT50 para el ovario en promedio fue de 34.5 ± 0.4°C no varió para los botones y las flores. Por su parte los pétalos de los botones presentan una LT50 21.5 ± 1.6°C y que para el caso de las flores en antesis fue 33% mayor. El desarrollo reproductivo frecuentemente requiere de la acumulación de cierta cantidad de estas unidades de frío. El tejido de estructuras jóvenes tolera más el aumento de la temperatura, que sus contrapartes maduras.

Bi-2223 HTS winding in toroidal configuration for SMES coil

International Nuclear Information System (INIS)

Kondratowicz-Kucewicz, B; Kozak, S; Kozak, J; Wojtasiewicz, G; Majka, M; Janowski, T

2010-01-01

Energy can be stored in the magnetic field of a coil. Superconducting Magnetic Energy Storage (SMES) is very promising as a power storage system for load levelling or power stabilizer. However, the strong electromagnetic force caused by high magnetic field and large coil current is a problem in SMES systems. A toroidal configuration would have a much less extensive external magnetic field and electromagnetic forces in winding. The paper describes the design of HTS winding for SMES coil in modular toroid configuration consist of seven Bi-2223 double-pancakes as well as numerical analysis of SMES magnet model using FLUX 3D package. As the results of analysis the paper presents the optimal coil configuration and the parameters such as radius of toroidal magnet, energy stored in magnet and magnetic field distribution.

Tensile damage and its influence on the critical current of Bi2223/Ag superconducting composite tape

International Nuclear Information System (INIS)

Ochiai, S; Nagai, T; Okuda, H; Oh, S S; Hojo, M; Tanaka, M; Sugano, M; Osamura, K

2003-01-01

We have studied the tensile behaviour of Bi2223 superconducting composite tapes at room temperature, and the influence of the tensile damages introduced at room temperature on the critical current I c and the n values at 77 K. In the measurement of the I c and n values, the overall composite with a gauge length 60 mm was divided into six elements with a gauge length of 10 mm in order to find the correlation of the I c and n values of the overall composite to those of the local elements which constitute the composite. From the measured stress-strain curve of the composite and the calculated residual strain of the Bi2223 filaments, the intrinsic fracture strain of Bi2223 filaments was estimated to be 0.09-0.12%. When the applied strain was lower than the onset strain of the filament damage, the original I c and n values were retained both in the overall composite and the elements. In this situation, while the overall voltage at the transition from superconductivity to normal conductivity of the composite was the sum of the voltages of the constituent elements, among all elements the overall voltage was affected more by the element with the lower I c (higher voltage). The damage of the filaments arose first locally, resulting in a reduction of the I c and n values in the corresponding local element, even though the other elements retained the original I c and n values. In this situation, the voltage of the overall composite stemmed dominantly from that of the firstly damaged weakest element, and the overall I c and n values were almost determined by the values of such an element. After the local element was fully damaged, the damage arose also in other elements, resulting in segmentation of the filaments. Thus, the I c and n values were reduced in all elements. The correlation of I c between the overall composite and the elements could be described comprehensively for non-damaged and damaged states from the voltage-current relation

EVALUACIÓN DEL COMPORTAMIENTO DE ARCILLAS SOMETIDAS A DIFERENTES TIEMPOS DE EXPOSICIÓN A ALTAS TEMPERATURAS AVALIAÇÃO DO COMPORTAMENTO DE ARGILAS SUBMETIDAS A DIFERENTES TEMPOS DE EXPOSIÇÃO A ALTAS TEMPERATURAS BEHAVIOR EVALUATION OF CLAYS SUBJECTED TO DIFFERENT EXPOSURES TIMES AT HIGH TEMPERATURES

Directory of Open Access Journals (Sweden)

Hugo Alexánder Rondón

2011-12-01

Full Text Available El artículo presenta el cambio que experimentan dos arcillas en sus propiedades índice, de expansión y resistencia a la compresión inconfinada cuando se someten a altas temperaturas (150, 225 y 300 °C durante tres tiempos de exposición (1, 7 y 15 días. Además se estudió si las arcillas recuperan las propiedades mencionadas después de ser sometidas a altas temperaturas y de ser nuevamente expuestas a la temperatura ambiente durante una semana en el laboratorio. El objetivo general de la investigación es evaluar si la aplicación de temperatura puede utilizarse como mecanismo de estabilización de arcillas o fabricación de llenante mineral. Los resultados muestran que la plasticidad, el potencial de expansión y la resistencia a la compresión simple de las arcillas ensayadas disminuyen cuando se eleva la temperatura de las muestras entre 150 ºC y 300 ºC y se incrementa el tiempo de exposición. También se encontró que la recuperación de las propiedades de las arcillas es nula cuando se someten a 300 °C durante 15 días.O artigo apresenta a mudança que experimentam duas argilas em suas propriedades índice, de expansão e resistência à compressão não confinada quando se submetem a altas temperaturas (150, 225 e 300 °C durante três tempos de exposição (1,7 e 15 dias. Ademais estudou-se se as argilas recuperam as propriedades mencionadas, após ser submetidas a altas temperaturas e de ser novamente expostas à temperatura ambiente durante uma semana no laboratório. O objetivo geral da pesquisa é avaliar se a aplicação de temperatura pode ser utilizada como mecanismo de estabilização de argilas ou fabricação de filler mineral. Os resultados mostram que a plasticidade, o potencial de expansão e a resistência à compressão simples das argilas ensaiadas diminuem quando se eleva a temperatura das mostras entre 150 ºC e 300 ºC e se incrementa o tempo de exposição. Também se encontrou que a recuperação das

Microestructura y comportamiento plástico de perovsquitas conductoras protónicas de alta temperatura

Directory of Open Access Journals (Sweden)

López-Robledo, M. J.

2005-10-01

Full Text Available The creep behaviour of high temperature proton conducting perovskites SrCe0.9Y0.1O3-δ and Sr3Ca1.18Nb1.82O9-δ fabricated by laser fusion has been studied. Their microstructure has been studied both in the as-received and crept samples by means of Scanning Electron Microscopy (SEM and Electron BackScattering Diffraction (EBSD, to correlate plastic behaviour with the evolution of the microstructure. The materials show a cellular structure consisting of elongated grains embedded in an amorphous phase and a strong bi-axial crystallographic texture. Deformation tests at constant stress (creep tests have been performed both in Ar atmosphere and in air. Rigid grain rotation has been observed in the crept samples by EBSD. The amorphous phase flows outside the sample during creep. Plastic behaviour of these materials is independent of the environmental atmosphere and is consistent with a mechanism of viscous flow of the amorphous phase controlled by diffusion.

Se ha estudiado el comportamiento en fluencia de perovsquitas conductoras protónicas de alta temperatura fabricadas por fusión láser, en particular los sistemas SrCe0.9Y0.1O3-δ y Sr3Ca1.18Nb1.82O9-δ. Se ha estudiado la microestructura antes y después de los ensayos mecánicos mediante Microscopía Electrónica de Barrido (MEB y Difracción de Electrones Retrodispersados (Electron BackScattering Diffraction, EBSD, con el objetivo de correlacionar el comportamiento plástico de estos materiales con su evolución microestructural. Los materiales analizados tienen una estructura celular de granos alargados, separados por una fase amorfa, y presentan una fuerte textura cristalográfica bi-axial. Se han realizado ensayos de deformación a carga constante (fluencia a diversas tensiones y temperaturas, en atmósfera inerte de Ar y en aire. Tras los ensayos, la fase intercelular fluye hacia el exterior de la muestra y se ha comprobado mediante EBSD que los granos rotan de forma rígida. El

Electrical properties of BiSrCaCuO films (2223)

International Nuclear Information System (INIS)

Okunev, V.D.; Pafomov, N.N.; Perekrestov, B.I.; Svistunov, V.M.

1996-01-01

The mechanisms of electrical conductivity of BiSrCaCuO films (2223) of different structural states are investigated. The films of an amorphous state (ρ = 10 3 - 10 10 Ohm centre dot cm) display a hopping conductivity with a variable hop length. Since the formation of a crystal structure (ρ = 10 - 10 3 Ohm centre dot cm) and up to the transition to a metal conductivity state (ρ ≅ 10 -2 Ohm centre dot cm) their electrical properties are similar to those of granular films featuring the exponential relation between specific resistance and separation between granules of metallic conductivity. In the vicinity of insulators-metal transition they feature the electrical conductivity-temperature relation with exponents 1/2 and 1/3. The transition to the metallic state is of a percolation nature and realized for a metal phase concentration of c m ≅ 0.2

Self-field AC losses in Bi-2223 superconducting tapes

International Nuclear Information System (INIS)

Mueller, K. H.; Leslie, K.E.

1996-01-01

Full text: The self-field AC loss in Bi-2223 silver sheathed tapes for AC currents of up to 100 A was measured at 77 K and frequencies of 60 Hz and 600 Hz using a lock-in amplifier. The frequency dependence indicated a purely hysteretic loss which can be well described in terms of the critical state model for a flat superconducting strip. The only parameter needed to predict the self-field AC loss is the critical current of the critical state. Because the loss voltage is extremely small compared with the inductive voltage, a very high accuracy of the lock-in amplifier phase setting is required. Unlike in loss measurements on cylindrical superconducting samples, in the case of the tape the measuring circuit leads have to be brought out from the surface forming a loop where the changing magnetic field induces an additional voltage. Only if the loop formed by the leads at the voltage tabs is large enough will the apparent power dissipation approach the real AC loss associated with the length of the sample probed

AC magnetic losses in Bi-2223/Ag tapes with different aspect ratios

Energy Technology Data Exchange (ETDEWEB)

Fang, J.; Luo, X.M.; Chen, D.X.; Collings, E.W.; Lee, E.; Sumption, M.D.; Alamgir, A.K.M.; Yi, H.P.; Fang, J.G.; Gu, C.; Guo, S.Q.; Liu, M.L.; Xin, Y.; Han, Z

2004-10-01

AC losses in multi-filamentary tapes depend on various parameters. Among them, the overall tape width and thickness are expected to have an important influence. In order to study this geometrical effect, five Bi-2223/Ag tapes with different aspect ratios from 5 to 26 have been prepared. AC losses have been measured at 77 K when a perpendicular AC magnetic field is applied. It has been found that at any frequencies the magnetic loss per cycle increases as the aspect ratio increases. For AC magnetic loss, with increasing frequency from 3 to 9000 Hz the losses as a function of frequency show a maximum if the field amplitude is much less than the full penetration field or increase continuously if the field amplitude is larger.

AC magnetic losses in Bi-2223/Ag tapes with different aspect ratios

International Nuclear Information System (INIS)

Fang, J.; Luo, X.M.; Chen, D.X.; Collings, E.W.; Lee, E.; Sumption, M.D.; Alamgir, A.K.M.; Yi, H.P.; Fang, J.G.; Gu, C.; Guo, S.Q.; Liu, M.L.; Xin, Y.; Han, Z.

2004-01-01

AC losses in multi-filamentary tapes depend on various parameters. Among them, the overall tape width and thickness are expected to have an important influence. In order to study this geometrical effect, five Bi-2223/Ag tapes with different aspect ratios from 5 to 26 have been prepared. AC losses have been measured at 77 K when a perpendicular AC magnetic field is applied. It has been found that at any frequencies the magnetic loss per cycle increases as the aspect ratio increases. For AC magnetic loss, with increasing frequency from 3 to 9000 Hz the losses as a function of frequency show a maximum if the field amplitude is much less than the full penetration field or increase continuously if the field amplitude is larger

RELACIONES HÍDRICAS Y TEMPERATURAS ALTAS EN FRIJOL DEL TIPO "FLOR DE MAYO"

Directory of Open Access Journals (Sweden)

Edwin Javier Barrios-Gómez

2011-01-01

Full Text Available Se estudió el efecto del déficit hídrico del suelo y temperatura alta del aire en las relaciones hídricas y temperatura del dosel del cultivo (Tc, rendimiento de semilla (RS y sus componentes en 8 variedades de frijol del tipo "Flor de Mayo" (FM y una variedad criolla. Se realizaron 3 experimentos de campo; Montecillo en riego (MR con la aplicación de agua de la siembra a la madurez, Montecillo en secano (MS con la lluvia como fuente única de humedad y Celaya en secano (CS con lluvia y 2 riegos suplementarios en floración. Se utilizó una dosis de fertilización de 80 kg.ha-1 de nitrógeno y 40 kg.ha-1 de fósforo. En MR el potencial hídrico foliar ( =-0,33 Mpa, osmótico ( =-1,26 Mpa y de turgencia y (P=0,93 Mpa fue más alto que en CS ( =-0,77, =-1,36 y P=0,59 Mpa y MS ( =-1,22, =-1,57 y P=0,35 Mpa; MS, con mayor deficiencia hídrica del suelo, tuvo mayor reducción en y , y mayor grado de ajuste osmótico (AO=0,70 Mpa. El AO estuvo positiva y significativamente asociado con RS y biomasa aérea final (BMAF en los 2 ambientes de secano. La Tc en MR (26,7°C fue más baja que en CS (30,8°C y MS (36,6°C; el estrés por calor se agudizó con el descenso en el contenido hídrico de las plantas en el ambiente más seco (MS; Tc se relacionó negativa y significativamente con y en MS. La alta Tc también tuvo efecto significativo en la producción de BMAF y RS y sus componentes; la alta Tc redujo el RS, BMAF, número de vainas normales.m-2 (VN.m-2 y peso de 100 semillas (P100S en 12,5, 10,7, 10,2 y 3,4% por cada ºC (-1 ºC de aumento en la Tc, respectivamente.

Efeito de altas temperaturas na resistência à compressão, resistência à tração e módulo de deformação do concreto

Directory of Open Access Journals (Sweden)

A. A. A. de Souza

Full Text Available Este trabalho teve como objetivo a investigação experimental do comportamento do concreto quando submetido a elevadas temperaturas. Um concreto de utilização comum em nossa região, com cimento e agregados usuais, misturados em proporções também usuais (traço, foi submeti- do a temperaturas de 300 °C, 600°C e 900 °C , de maneira a se avaliar prováveis alterações na resistência à compressão, na resistência à tração e no módulo de deformação deste concreto. O efeito do resfriamento rápido do concreto, usual em intervenções de combate a incêndios, foi avaliado; alguns dos corpos-de-prova submetidos às altas temperaturas estipuladas foram resfriados rapidamente e outros foram resfriados len- tamente (ao ambiente. A recuperação provável das propriedades mecânicas analisadas, com a reidratação do concreto - com possível redução após o efeito das altas temperaturas aplicadas - também foi avaliada; corpos-de-prova submetidos às altas temperaturas estipuladas e resfriados lentamente, foram parte imersos em água e parte envoltos em filme plástico e a seguir, cada parte correspondente foi avaliada, em relação às propriedades do concreto pesquisadas, para as idades do concreto de 28, 56, 112 e 224 dias após o resfriamento lento. Ao final deste trabalho, importantes resultados sobre o efeito de altas temperaturas nas propriedades mecânicas do concreto puderam ser obtidos; contribuindo, em muito, para o estabelecimento de parâmetros para o projeto de recuperação de estruturas submetidas ao efeito do fogo.

Current distribution and enhancement of the engineering critical current density in multifilament Bi-2223 tapes

DEFF Research Database (Denmark)

Wang, W.G.; Jensen, M.B.; Kindl, B.

2000-01-01

The spatial distribution of the critical current density (Jc) and engineering critical current density (Je) along the tape width direction was studied by a cutting technique on Bi-2223 multifilamentary tapes. In general, an increase of Jc towards the centre of the tape was measured. We attribute...... microstructure with a great amount of secondary phases. Local variation of Jc was measured within the centre segment of the tape. This indicates the influence of other factors on Jc, such as filament shape, connectivity of the filaments, and sausaging. Enhancement of Je has been pursued in which average Je of 12...

Improvement of critical currents in Bi-2223 bulk superconductors

International Nuclear Information System (INIS)

Eujen, R.; Brauer, D.J.; Huedepohl, J.

1991-01-01

Potential applications of the high-Tc superconductors for energy transport or high-field magnets require high critical current densities. A limiting factor in polycrystalline oxidic materials is the quality of the grain boundaries. Weak links have been made responsible for the steep decrease in the critical current density j c upon application of even weak magnetic fields of YBa CuO whereas flux creep seems to dominate the obtainable j c values for the Bi-Sr-Ca-Cu-O system (BSCCO) at 77 K. In the lead containing material (BPSCCO) the formation of a porous microstructure is enhanced by the platelike shape of the crystals. Special techniques such as powder-in-tube, hot isostatic pressing, zone melting or application of fluxes have been used in order to improve the grain contacts. A positive influence of fluxes on j c , e.g. by addition of Ca 2 CuO 3 or Ag 2 O, has been reported. In this study we have investigated the influence of various compositions and conditions on the formation of the BSCCO-2223 phase (T c ca. 107 K), the critical current density j c , and the magnet field dependence of the a.c. susceptibility. (orig.)

Propiedades mecánicas del telururo de bismuto (Bi2Te3 procesado mediante torsión bajo alta presión (HPT

Directory of Open Access Journals (Sweden)

Santamaría, Jon Ander

2013-06-01

Full Text Available Bismuth telluride, Bi2Te3, is the main thermoelectric material currently in use for commercial cooling devices or for energy harvesting near room temperature. Because of its highly anisotropic layered structure, Bi2Te3 is very brittle, failing by cleavage along its basal plane. Refining its grain size is expected to increase its toughness with the advantage that, simultaneously, its thermoelectric “figure of merit” results increased. In this work, powders of the compound have been compacted by conventional methods as well as by severe plastic deformation under high pressure (3 GPa using high pressure torsion (HPT, one turn at room temperature. Near-theoretical density has been achieved. The hardness and toughness of the compacts have been assessed by micro and nano-indentation.Actualmente el telururo de bismuto (Bi2Te3 es el material termoeléctrico más ampliamente usado en sistemas de refrigeración comerciales o en la conversión de energía en torno a temperatura ambiente. Debido a su estructura laminar altamente anisótropa, el Bi2Te3 es muy frágil y suele agrietarse fácilmente a lo largo de su plano basal. Se espera que el afino del tamaño de grano incremente su tenacidad, con la ventaja de que al mismo tiempo la figura de mérito termoeléctrica se vea incrementada. En este trabajo, polvos del compuesto Bi2Te3 se han compactado mediante dos métodos convencionales y mediante deformación plástica severa bajo alta presión (3 GPa usando la técnica HPT (torsión a alta presión, 1 giro de deformación. Se ha conseguido una densidad cercana a la teórica. La dureza y tenacidad de los compuestos se han ensayado mediante micro- y nano- indentación.

Estudio de seguridad del acoplamiento de un reactor de alta temperatura (VHTR) con una planta de producción de hidrógeno, análisis de los accidentes relevantes asociados

OpenAIRE

Moyart, Quentin

2008-01-01

Un estudio preliminar de seguridad dedicado al acoplamiento de un reactor nuclear de muy alta temperatura (Very High Temperature Reactor) con una planta de producción de hidrógeno (HYdrogen Production Plant) según el proceso de electrólisis a alta temperatura (High Temperature Electrolysis) se presenta en esta memoria. La primera parte de este documento está dedicada a las hipótesis de funcionamiento elegidas para el estudio, así como a la breve descripción de las dos instalaciones en el esta...

Corrosión a alta temperatura de acero al carbono y acero inoxidable austenítico en atmósferas contaminadas por CO2

OpenAIRE

Proy Pérez, Manuel

2014-01-01

Los efectos a veces catastróficos producidos por los procesos de corrosión a alta temperatura en atmósferas contaminadas por agentes agresivos, poseen la suficiente relevancia para ser objeto de estudio en los próximos años, debido a que en muchas ocasiones no están definidos claramente. Los aceros al carbono y los inoxidables austeníticos son materiales potencialmente utilizables en condiciones de elevada temperatura gracias a su excelente relación entre sus propiedades est...

Temperatura corporal, índice Aldrete e Kroulik e alta do paciente da Unidade de Recuperação Pós-Anestésica

Directory of Open Access Journals (Sweden)

Fernanda Salim Ferreira de Castro

2012-08-01

Full Text Available A alta do paciente da recuperação pós-anestésica (RPA depende, dentre outros fatores, do retorno à normotermia e do escore alcançado pelo Índice de Aldrete e Kroulik. Sendo assim, o objetivo deste estudo foi verificar a relação entre o Índice de Aldrete e Kroulik e a temperatura corporal dos pacientes. O local de pesquisa foi o Hospital Universitário da Universidade de São Paulo. O cálculo amostral foi determinado por conveniência e foi constituído por 60 pacientes, entre 18 e 60 anos, submetidos à anestesia geral. Foram verificados a temperatura corporal na região timpânica e o Índice de Aldrete e Kroulik do paciente na recepção e alta da recuperação pós-anestésica. Os dados obtidos foram processados pelo pacote estatístico SPSS, com um nível de 5% de significância, e aplicaram-se o teste de Spearman e o teste de Wilcoxon. Conclui-se que não houve correlação significativa entre os dois parâmetros indicativos de alta.

Growth and superconducting properties of Bi2Sr2Ca2Cu3O10 single crystals

International Nuclear Information System (INIS)

Clayton, N; Musolino, N; Giannini, E; Garnier, V; Fluekiger, R

2004-01-01

Single crystals of Bi 2 Sr 2 Ca 2 Cu 3 O 10 (Bi-2223) have been grown using the travelling solvent floating zone technique in an image furnace. Annealing the crystals under high pressures of O 2 increased their critical temperature to 109 K, and resulted in sharp superconducting transitions of ΔT c = 1 K. The superconducting anisotropy of Bi-2223 was found to be ∼ 50, from measurements of the lower critical field with the magnetic field applied parallel and perpendicular to the c-axis. The anisotropy of Bi-2223 is significantly reduced compared to that of Bi 2 Sr 2 CaCu 2 O 8 (Bi-2212), and this accounts for the enhanced irreversibility fields in Bi-2223. Furthermore, Bi-2223 has a higher critical current density, and a reduced magnetic relaxation rate compared to Bi-2212, which are both signatures of more effective pinning in Bi-2223 due to its reduced anisotropy

Exigência de Lisina para Pintos de Corte Machos Mantidos em Ambiente com Alta Temperatura

Directory of Open Access Journals (Sweden)

Borges Aurélio Ferreira

2002-01-01

Full Text Available Foram utilizados 400 pintos de corte machos da linhagem Avian Farms, com peso médio de 35 ± 0,15 g, no período de 1 a 21 dias de idade, mantidos em ambiente com alta temperatura ( 29,1 ± 0,39ºC, umidade relativa em 59,7 ± 3,16%, temperatura de globo negro em 28,9 ± 0,42ºC e índice de temperatura de globo e umidade (ITGU em 77,4 ± 0,59. O delineamento utilizado foi o inteiramente casualizado, com cinco tratamentos (1,04; 1,10; 1,16; 1,22; e 1,28% de lisina total na ração, oito repetições e 10 aves por repetição. Avaliou-se o efeito de níveis de lisina total sobre desempenho, consumo de lisina total, deposições de proteína e gordura na carcaça e pesos absoluto e relativo da gordura abdominal e do coração, fígado e intestinos. O fornecimento de ração e água foi à vontade. Os níveis de proteína bruta, minerais e vitaminas atenderam às exigências dos animais. Verificou-se efeito quadrático dos níveis de lisina total da ração sobre o ganho de peso, que aumentou, e a conversão alimentar, que melhorou até os níveis de 1,20 e 1,24%, respectivamente. O consumo de ração não variou, enquanto o consumo de lisina total aumentou em razão dos tratamentos. Não se observou efeito dos níveis de lisina da ração sobre os pesos absoluto e relativo do coração e do intestino e o peso relativo do fígado. No entanto, o peso absoluto do fígado aumentou de forma quadrática até o nível de 1,17% de lisina total da ração. Com relação à taxa de deposição de proteína, constatou-se aumento quadrático até o nível de 1,26% de lisina total, enquanto a taxa de deposição de gordura não variou com o nível de lisina da ração. Concluiu-se que frangos de corte machos no período de 1 a 21 dias de idade, submetidos à alta temperatura (29,1ºC, exigem 1,20% de lisina total, correspondente a 1,02% de lisina digestível.

Tolerância de sementes de linhagens de milho à alta temperatura de secagem Tolerance of corn lines seeds to high drying temperature

Directory of Open Access Journals (Sweden)

Solange Carvalho Barrios Roveri José

2004-10-01

Full Text Available Cultivares tolerantes a altas temperaturas de secagem proporcionam redução no tempo de secagem, uma etapa crítica no sistema de produção de sementes de milho (Zea mays L.. Nesta pesquisa, foi avaliada a tolerância à alta temperatura de secagem de sementes de linhagens de milho, por meio de testes de germinação e vigor. As sementes foram colhidas manualmente em espigas com teor de água em torno de 35% e secas artificialmente à 45 C até atingirem 11% de teor de água. Em seguida, foram submetidas aos testes de primeira contagem e contagem final de germinação, envelhecimento acelerado, teste de frio sem solo e de condutividade elétrica. Houve diferenças significativas nos valores de germinação e vigor de sementes das diferentes linhagens, sendo então classificadas em tolerantes e intolerantes. Pelos resultados, conclui-se que a sensibilidade das sementes à injúria por secagem à alta temperatura é dependente da linhagem.High drying temperature tolerant cultivars provide a reduction in the drying period, a critical phase of the corn seeds (Zea mays L. production system. In this research the tolerance of corn lines seeds to high drying temperature was evaluated by the germination and vigor tests. Seeds were handpicked in ears with water content around 35% and dried artificially at 45ºC up to 11% water content. Then, the seeds were submitted to the first and final germination counting tests, accelerated aging, cold test without soil and electrical conductivity. There were significant differences in the germination and vigor values of seeds from different lines, being classified into tolerant and intolerant. The results permitted to conclude that sensitivity of seeds to high drying temperature injury depends on the lines.

Recubrimientos contra la corrosión a alta temperatura para componentes de turbinas de gas

Directory of Open Access Journals (Sweden)

Agüero, A.

2007-10-01

Full Text Available Hot section gas turbine components are made of superalloys, developed to withstand high temperatures in conditions in which mechanical stresses are high and that require high surface stability. However, during the 50s it became evident that compositions resulting in high mechanical strength for these materials were not compatible with those offering optimal protection from the working environments. The idea of employing protective coatings over materials with high mechanical strength resulted therefore from this situation. Presently, both aeronautic and power generation turbines operate at temperatures within the 900-1400 °C, thanks to these coatings, indispensable for their correct operation. In this work, the principal degradation mechanisms in these operating conditions and the different type of coatings presently employed by the industrial sector are described, beginning by the oldest Ni or Co aluminides, following with the addition of other metals such as Pt, Cr, etc. to the former coatings in order to increase their useful life, continuing with the overlay MCrAlY coatings and finishing with the thermal barrier coating systems. Moreover, the corresponding deposition techniques industrially employed to deposit these coatings are described, and finally, an insight of the latest research lines currently being developed is also included.

Los componentes de las zonas calientes de las turbinas de gas están hechos de superaleaciones desarrolladas para soportar altas temperaturas, en condiciones en que las tensiones mecánicas son relativamente altas y en las que se requiere una alta estabilidad superficial. Sin embargo, durante la década de 1950-60, se hizo evidente que las composiciones que aumentaban la resistencia mecánica de estos materiales y aquellas que ofrecían una óptima protección contra ambientes agresivos no eran compatibles. Esto, condujo a la idea de emplear recubrimientos protectores sobre materiales con alta

Invernaderos: seguimientos de temperatura y oxígeno

OpenAIRE

Sonnenholzner, Stanislaus

2002-01-01

Invernaderos: Seguimientos de Temperatura y Oxígeno Entre diciembre del 2001 y mayo del 2002 se realizaron dos series de experimentos para evaluar el efecto de las temperaturas altas en la supervivencia y el crecimiento del camarón utilizando invernaderos.

Geometry dependence of magnetic and transport AC losses in Bi-2223/Ag tapes with different aspect ratios

Energy Technology Data Exchange (ETDEWEB)

Fang, J [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Luo, X M [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Chen, D X [ICREA and Grup Electromagnetisme, Departament de Fisica, Universitat Autonoma Barcelona, 08193 Bellaterra (Spain); Alamgir, A K M [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Collings, E W [MSE, Ohio State University, Columbus, OH 43210 (United States); Lee, E [MSE, Ohio State University, Columbus, OH 43210 (United States); Sumption, M D [MSE, Ohio State University, Columbus, OH 43210 (United States); Fang, J G [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Yi, H P [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Song, X H [Innova Superconductor Technology Co., Ltd, 7 Rongchang Dongjie, Longsheng Industrial Park, Beijing Economic and Technological Development Area, 100176 (China); Guo, S Q [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Liu, M L [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Xin, Y [Innopower Superconductor Cable Co., Ltd, 7 Rongchang Dongjie, Longsheng Industrial Park, Beijing Economic and Technological Development Area, 100176 (China); Han, Z [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China)

2004-10-01

On five Bi-2223/Ag tapes with different aspect ratios from 5 to 26, AC losses have been measured at 77 K while a parallel AC magnetic field or a perpendicular AC magnetic field or a longitudinal AC transport current is applied. It has been found that at any frequency the perpendicular magnetic losses per cycle increase, but the parallel magnetic losses per cycle and the transport losses per cycle decrease as the aspect ratio increases. These experimental results are in accord with theoretical results. Meanwhile, we investigated the geometry dependence of the decay time constant of coupling current and that of full penetration field.

Geometry dependence of magnetic and transport AC losses in Bi-2223/Ag tapes with different aspect ratios

International Nuclear Information System (INIS)

Fang, J; Luo, X M; Chen, D X; Alamgir, A K M; Collings, E W; Lee, E; Sumption, M D; Fang, J G; Yi, H P; Song, X H; Guo, S Q; Liu, M L; Xin, Y; Han, Z

2004-01-01

On five Bi-2223/Ag tapes with different aspect ratios from 5 to 26, AC losses have been measured at 77 K while a parallel AC magnetic field or a perpendicular AC magnetic field or a longitudinal AC transport current is applied. It has been found that at any frequency the perpendicular magnetic losses per cycle increase, but the parallel magnetic losses per cycle and the transport losses per cycle decrease as the aspect ratio increases. These experimental results are in accord with theoretical results. Meanwhile, we investigated the geometry dependence of the decay time constant of coupling current and that of full penetration field

Self-field AC losses and critical currents in multi-tube Ag-Bi-2223 conductors

Energy Technology Data Exchange (ETDEWEB)

Ciszek, M; Ashworth, S P; Campbell, A M [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); James, M P; Glowacki, B A [IRC in Superconductivity, University of Cambridge, Madingley Road, Cambridge CB3 0HE (United Kingdom); Department of Materials Science and Metallurgy, University of Cambridge, Pembroke Street, Cambridge CB2 3QZ (United Kingdom); Garre, R; Conti, S [Centro Ricerche Europa Metalli, Fornaci di Barga, LU (Italy)

1996-05-01

The purpose of this work was to investigate the influence of different technological treatments of silver sheathed Bi-2223 tapes on the critical current density and the AC transport losses. The tapes were produced using the 'tube-in-tube' technique, by including a silver rod in the centre of the superconducting powder during packing of the silver tube. The aim of the process is to increase the silver to superconductor surface area and thus also the alignment at the centre of the conductor ceramic core. AC transport losses were measured by means of an electrical method using sinusoidally varying currents in the frequency range 30-180 Hz. In this range the power losses are hysteretic. The measured variation in losses from those predicted by a critical state model is attributed to the complex geometry of superconducting regions existing in these tapes. (author)

Superconducting joint of Bi-2223/Ag superconducting tapes by diffusion bonding

International Nuclear Information System (INIS)

Guo Wei; Zou Guisheng; Wu Aiping; Wang Yanjun; Bai Hailin; Ren Jialie

2009-01-01

61-Filaments Bi-2223/Ag superconducting tapes have been joined by diffusion bonding. The critical currents (I C s) of the joints are obtained by using standard four probe method under no magnetic field in the liquid nitrogen. The microstructures of the joints are evaluated by the electron microscope in electron backscatter diffraction mode and the phase compositions of the superconducting cores of the joint and the original tape are determined by X-ray diffraction (XRD). The results show diffusion bonding is effective bonding technique for HTS tapes, and the bonding time is reduced greatly from hundreds of hours to a few hours, and the bonding pressure also changes from 140-4000 MPa to 3 MPa. Furthermore, the diffusion bonding joints sustain superconducting properties, and the critical current ratios (CCR O ) of the joints are in the range of 35%-80%. Microstructures of the typical joint display a good bonding and some defects existed in traditional method are avoided. XRD results show that the phase compositions of the superconducting cores have no obvious changes before and after diffusion bonding, which offers physical and material bases for high superconducting property of the joints.

Comparison of self-field effects between Bi-2223/Ag tapes and pancake coils

International Nuclear Information System (INIS)

Alamgir, A.K.M.; Gu, C.; Han, Z.

2005-01-01

Knowledge on self-field behavior in HTS tape and coil becomes important for the design of HTS devices. We report on the comparative nature and influence of self-field in Bi-2223/Ag tape and pancake coils in terms of critical current and ac loss. Measured dc and ac properties of short tape and pancake coils are verified based on the self-field. It is proved that perpendicular component of self-field acting in opposite direction at the two halves of tape-width determines critical current in short tape and single-turn coil. On the other hand, perpendicular component of self-field pointed in the same direction at the two halves of tape-width determines critical current in multi-turn coils. Influence of magnitude and orientation of self-field on ac loss is also investigated for a series of pancake coils based on the measured self-field ac loss in short sample

Comparison of self-field effects between Bi-2223/Ag tapes and pancake coils

Energy Technology Data Exchange (ETDEWEB)

Alamgir, A.K.M. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China)]. E-mail: alam643@yahoo.com; Gu, C. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China); Han, Z. [Applied Superconductivity Research Center, Department of Physics, Tsinghua University, Building Li Zhai, Room 209, Beijing 100084 (China)

2005-08-15

Knowledge on self-field behavior in HTS tape and coil becomes important for the design of HTS devices. We report on the comparative nature and influence of self-field in Bi-2223/Ag tape and pancake coils in terms of critical current and ac loss. Measured dc and ac properties of short tape and pancake coils are verified based on the self-field. It is proved that perpendicular component of self-field acting in opposite direction at the two halves of tape-width determines critical current in short tape and single-turn coil. On the other hand, perpendicular component of self-field pointed in the same direction at the two halves of tape-width determines critical current in multi-turn coils. Influence of magnitude and orientation of self-field on ac loss is also investigated for a series of pancake coils based on the measured self-field ac loss in short sample.

Development of Pb-rich (Bi, Pb) sub 3 Sr sub 2 Ca sub 2 Cu sub 1 O sub x phase during reformation of lead doped 2223 superconducting phase from melt quenched glass. [BiPbSrCaCuO

Energy Technology Data Exchange (ETDEWEB)

Oezkan, N; Glowacki, B A [IRC in Superconductivity, Univ. of Cambridge (United Kingdom)

1992-05-01

The reformation process of the lead doped superconducting 2223 phase from the melt quenched glass was investigated. It was shown that during the crystallisation of the glass a new lead rich phase, Bi{sub 0.5}Pb{sub 3}Sr{sub 2}Ca{sub 2}Cu{sub 1}O{sub x}, was formed and severe copper segregation was observed. The volume fraction of the high Tc 2223 phase increased with annealing time for an annealing temperature of 840degC. A glass sample annealed at 840degC for 150 h showed two superconducting transitions Tc = 107 K and Tc = 70 K. (orig.).

Electrical and mechanical properties of Bi-2223/Ag/barrier/Ag composite tapes

International Nuclear Information System (INIS)

Kovac, P.; Husek, I.; Goemoery, F.; Oduleye, O.O.; Alford, N.McN.; Pachla, W.; Diduszko, R.

2000-01-01

Bi-2223/Ag/barrier/Ag single-core tapes with various oxide barrier materials (BaZrO 3 , SrCO 3 , ZrO 2 and Al 2 O 3 ) have been prepared by PIT. The I-V curves and ac susceptibility measurements have been performed for tapes with identical heat treatment history. Young's moduli of these tape samples have been evaluated by three-point bending and the structure of barrier powders and BSCCO cores was analysed by SEM and XRD, respectively. It was found that the shape of I-V curves, the current transfer lengths and the mechanical properties of tapes are all affected by the oxide barrier type and the barrier thickness, as well as by its porosity and uniformity. This is because the oxide barrier controls the oxygen diffusion during the tape heat treatment and simultaneously the HTS phase formation kinetics, its purity and content within the superconducting core. On the base of the results obtained for single-core tapes, two kinds of multifilamentary composite were made and tested. (author)

Conceptual design of a 20-kA current lead using forced-flow cooling and Ag-alloy-sheathed Bi-2223 high-temperature superconductors

International Nuclear Information System (INIS)

Heller, R.; Hull, J.R.

1994-01-01

High-temperature superconductors (HTSs), consisting of Bi-2223 HTS tapes sheathed with Ag alloys are proposed for a 20-kA current lead for the planned stellarator WENDELSTEIN 7-X. Forced-flow He cooling is used, and 4-K He cooling of the whole lead as well as 60-K He cooling of the copper part of the lead, is discussed. Power consumption and behavior in case of loss of He flow are given

Simulation of ferromagnetic shielding to the critical current of Bi2223/Ag tape under external fields

Energy Technology Data Exchange (ETDEWEB)

Gu Chen [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Alamgir, A K M [Faculty of Engineering, Yokohama National University, 75-9 Tokiwadai, Hodogaya-ku, Yokohama (Japan); Qu Timing [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Han, Z [Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China)

2007-03-15

Ferromagnetic material was electroplated onto the surface of the Bi2223/Ag multi-filamentary tape and as a result changed the I{sub c}(B) characteristic of the tape correspondingly. A numerical simulation was used to investigate the influence of ferromagnetic shielding (FS) on the performance of the tape, in particular the I{sub c} behaviour under perpendicular external fields. Using finite element analysis, we are able to understand how FS alters the flux distribution within the superconductor region under any arbitrary shielding structure. The shielding width, thickness and nonlinear property of the ferromagnetic material were taken into account for the simulation. Finally, optimized shielding parameters in association with different operating fields were suggested and these values could be considered for the next run of experimental work.

Simulation of ferromagnetic shielding to the critical current of Bi2223/Ag tape under external fields

International Nuclear Information System (INIS)

Gu Chen; Alamgir, A K M; Qu Timing; Han, Z

2007-01-01

Ferromagnetic material was electroplated onto the surface of the Bi2223/Ag multi-filamentary tape and as a result changed the I c (B) characteristic of the tape correspondingly. A numerical simulation was used to investigate the influence of ferromagnetic shielding (FS) on the performance of the tape, in particular the I c behaviour under perpendicular external fields. Using finite element analysis, we are able to understand how FS alters the flux distribution within the superconductor region under any arbitrary shielding structure. The shielding width, thickness and nonlinear property of the ferromagnetic material were taken into account for the simulation. Finally, optimized shielding parameters in association with different operating fields were suggested and these values could be considered for the next run of experimental work

Produção de cultivares de brócolis de inflorescência única em condições de altas temperaturas

OpenAIRE

Seabra Junior,Santino; Neves,Jucimar F; Dias,Leonardo DE; Silva,Leandro B; Nodari,Ivan DE

2014-01-01

Este trabalho teve como objetivo avaliar o desempenho de cultivares de brócolis tipo inflorescência única produzidas em condições de altas temperaturas, de junho a setembro de 2012, em Cáceres-MT. O estudo foi conduzido utilizando-se delineamento em blocos casualizados, composto por quatro repetições e quinze cultivares de brócolis (Shiguemori, Lord Summer, Marathon, Imperial, Avenger, Salinas, Brócolis de Cabeça, Bozano, Legacy, BRO 68, ...

Altas temperaturas y nefrología: a propósito del cambio climático

Directory of Open Access Journals (Sweden)

Alberto de Lorenzo

2017-09-01

Full Text Available Sabemos que el cambio climático afecta de forma considerable a la salud, si bien son muy pocos los estudios que recogen sus consecuencias a nivel renal. Se ha visto como las olas de calor aumentan la morbimortalidad cardiovascular y respiratoria, pero también el riesgo de fracaso renal agudo, así como el índice de ingresos de causa nefrológica, con la mortalidad que ello implica. Las situaciones de deshidratación repetidas en población expuesta de forma habitual a altas temperaturas parecen estar generando una nueva entidad dentro de la enfermedad renal crónica proteinúrica, cuyo mecanismo fisiopatológico se va dilucidando. Pero más allá de olas de calor y temperaturas extremas, se ha comprobado que existe una variación estacional del filtrado glomerular que pudiera facilitar el desarrollo de fracaso renal y alteraciones electrolíticas en periodos extremadamente cálidos. Entre las alteraciones del medio interno, parecen aumentar fundamentalmente las disnatremias, aunque es poca la evidencia bibliográfica al respecto. Los grupos de riesgo para presentar enfermedades asociadas al calor son ancianos, niños, enfermos crónicos, personas encamadas, discapacitados, sujetos que viven solos o con escaso contacto social y las poblaciones más desfavorecidas a nivel socioeconómico.

A feasibility study of high-strength Bi-2223 conductor for high-field solenoids

Science.gov (United States)

Godeke, A.; Abraimov, D. V.; Arroyo, E.; Barret, N.; Bird, M. D.; Francis, A.; Jaroszynski, J.; Kurteva, D. V.; Markiewicz, W. D.; Marks, E. L.; Marshall, W. S.; McRae, D. M.; Noyes, P. D.; Pereira, R. C. P.; Viouchkov, Y. L.; Walsh, R. P.; White, J. M.

2017-03-01

We performed a feasibility study on a high-strength Bi{}2-xPb x Sr2Ca2Cu3O{}10-x(Bi-2223) tape conductor for high-field solenoid applications. The investigated conductor, DI-BSCCO Type HT-XX, is a pre-production version of Type HT-NX, which has recently become available from Sumitomo Electric Industries. It is based on their DI-BSCCO Type H tape, but laminated with a high-strength Ni-alloy. We used stress-strain characterizations, single- and double-bend tests, easy- and hard-way bent coil-turns at various radii, straight and helical samples in up to 31.2 T background field, and small 20-turn coils in up to 17 T background field to systematically determine the electro-mechanical limits in magnet-relevant conditions. In longitudinal tensile tests at 77 K, we found critical stress- and strain-levels of 516 MPa and 0.57%, respectively. In three decidedly different experiments we detected an amplification of the allowable strain with a combination of pure bending and Lorentz loading to ≥slant 0.92 % (calculated elastically at the outer tape edge). This significant strain level, and the fact that it is multi-filamentary conductor and available in the reacted and insulated state, makes DI-BSCCO HT-NX highly suitable for very high-field solenoids, for which high current densities and therefore high loads are required to retain manageable magnet dimensions.

AC power losses in Bi-2223/Ag HTS tapes

International Nuclear Information System (INIS)

Savvides, N.; Reilly, D.; Mueller, K.-H.; Herrmann, J.

1998-01-01

Full text: We report measurements at 77 K of the transport ac losses of Bi-2223/Ag composite tapes. The investigated tapes vary from single filament to multifilament construction and include both conventional tapes and other conductor shapes with twisted filaments. The self-field ac losses were determined at 77 K and 60 Hz as a function of ac current amplitude (0 - 100 A). We observe different behaviour among tapes depending on their quality and strain history. For 'good' virgin tapes the experimental data are well described by the Norris equations for the dependence of power loss P on the amplitude I m of the transport current. The data of good monofilament tapes are fitted to the Norris equation P ∼ I m n for an elliptical cross section (ie. n = 3) and the data of good multifilament tapes are fitted to the Norris equation for a rectangular strip (ie. n = 4). Many specimens, however, show a range of behaviour with lower values of n. Based on our work on the effect of strain on the dc transport properties of tapes, we carried out detailed investigations of the effect of controlled applied bend strain on the ac loss. Our results show that irreversible damage to superconducting filaments (ie. cracks) cause the ac loss to rise and n to decrease with increasing strain. In addition, applied strains much greater than the irreversible strain limit cause the ac loss to increase by several orders of magnitude and become ohmic in character with n = 2. Theoretical work is in progress to model the observed behaviour

Ac susceptibility of a Bi-2223/Ag tape in a perpendicular field

International Nuclear Information System (INIS)

Savvides, N.; Mueller, K.-H.

1999-01-01

Full text: We report experimental measurements and theoretical calculations of the real ( X ') and imaginary or loss ( X '') parts of the ac susceptibility as a function of temperature T = 4 - 130 K, frequency ω/2π = 5 Hz - 5 kHz and ac magnetic field amplitude μ 0 H m = 0.02 - 7 mT for of a monofilament silver-sheathed Bi-2223 tape. The susceptibilities consist of a hysteretic component due to ac loss ( Xsc '') in the superconductor core and an eddy current component due to eddy current loss ( Xed '') in the silver sheath. At high temperatures the low frequency limit is used to calculate the hysteretic and eddy current susceptibilities while at low temperatures the susceptibility is found to be due to eddy currents flowing along the edges of the tape. The measured loss at low frequencies (< 50 Hz) and high temperatures is dominated by the hysteresis loss which varies with amplitude but is essentially independent of frequency. At higher frequencies the eddy current loss of the silver sheath becomes dominant and it increases dramatically with frequency at both low and high temperatures

Detection and evaluation of corrosion zones at high temperature in steam generators; Deteccion y evaluacion de zonas de corrosion en alta temperatura de generadoras de vapor

Energy Technology Data Exchange (ETDEWEB)

Martinez Villafane, Alberto; Chacon Nava, Jose G; Huerta Espino, Mario; Mojica Calderon, Cecilio; Castillo Viveros, Antonio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1991-12-31

This paper presents the methodology for the detection and evaluation of high corrosion zones at high temperature. The results found up to now, show a critical zone in the Babcock Hitachi design, specifically in the high temperature reheater in the zone nearby the outlet header. In the normalized design CE (Mitsubishi) of 300 MW and CE (Canada) of 300 MW, the results found in recent years show small thickness reduction, therefore a good operation of these steam generators is recognized. [Espanol] En este trabajo se presenta la metodologia para la deteccion y evaluacion de zonas de corrosion en alta temperatura. Los resultados encontrados hasta el momento muestran una zona critica en el diseno Babcock Hitachi, especificamente en el recalentador de alta temperatura en la zona cercana al cabezal de salida. En el diseno normalizado CE (Mitsubishi) de 300 MW y CE (Canada) de 300 MW, los resultados encontrados en anos recientes muestran poca disminucion de espesor, por lo que se considera una buena operacion de estos generadores de vapor.

Detection and evaluation of corrosion zones at high temperature in steam generators; Deteccion y evaluacion de zonas de corrosion en alta temperatura de generadoras de vapor

Energy Technology Data Exchange (ETDEWEB)

Martinez Villafane, Alberto; Chacon Nava, Jose G.; Huerta Espino, Mario; Mojica Calderon, Cecilio; Castillo Viveros, Antonio [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1990-12-31

This paper presents the methodology for the detection and evaluation of high corrosion zones at high temperature. The results found up to now, show a critical zone in the Babcock Hitachi design, specifically in the high temperature reheater in the zone nearby the outlet header. In the normalized design CE (Mitsubishi) of 300 MW and CE (Canada) of 300 MW, the results found in recent years show small thickness reduction, therefore a good operation of these steam generators is recognized. [Espanol] En este trabajo se presenta la metodologia para la deteccion y evaluacion de zonas de corrosion en alta temperatura. Los resultados encontrados hasta el momento muestran una zona critica en el diseno Babcock Hitachi, especificamente en el recalentador de alta temperatura en la zona cercana al cabezal de salida. En el diseno normalizado CE (Mitsubishi) de 300 MW y CE (Canada) de 300 MW, los resultados encontrados en anos recientes muestran poca disminucion de espesor, por lo que se considera una buena operacion de estos generadores de vapor.

Influence of B4C-doping and high-energy ball milling on phase formation and critical current density of (Bi,Pb)-2223 HTS

Science.gov (United States)

Margiani, N. G.; Mumladze, G. A.; Adamia, Z. A.; Kuzanyan, A. S.; Zhghamadze, V. V.

2018-05-01

In this paper, the combined effects of B4C-doping and planetary ball milling on the phase evolution, microstructure and transport properties of Bi1.7Pb0.3Sr2Ca2Cu3Oy(B4C)x HTS with x = 0 ÷ 0.125 were studied through X-ray diffraction (XRD), scanning electron microscopy (SEM), resistivity and critical current density measurements. Obtained results have shown that B4C additive leads to the strong acceleration of high-Tc phase formation and substantial enhancement in Jc. High-energy ball milling seems to produce a more homogeneous distribution of refined doped particles in the (Bi,Pb)-2223 HTS which results in an improved intergranular flux pinning and better self-field Jc performance.

Produção de cultivares de brócolis de inflorescência única em condições de altas temperaturas

OpenAIRE

Seabra Junior, Santino; Neves, Jucimar F; Dias, Leonardo DE; Silva, Leandro B; Nodari, Ivan DE

2014-01-01

Este trabalho teve como objetivo avaliar o desempenho de cultivares de brócolis tipo inflorescência única produzidas em condições de altas temperaturas, de junho a setembro de 2012, em Cáceres-MT. O estudo foi conduzido utilizando-se delineamento em blocos casualizados, composto por quatro repetições e quinze cultivares de brócolis (Shiguemori, Lord Summer, Marathon, Imperial, Avenger, Salinas, Brócolis de Cabeça, Bozano, Legacy, BRO 68, Bibou, Yahto, Calabrês de Cabeça, Romanesco e Green Sto...

Estudio de la región rica en Bi2O3 en el sistema binario ZnO-Bi2O3

Directory of Open Access Journals (Sweden)

Caballero, A. C.

2004-08-01

Full Text Available Ceramic materials based in the ZnO- Bi2O3 system have their principal application as varistors. The binary system ZnO-Bi2O3 is specially relevant to the formation of the microstructure responsable of the varistor behaviour. The study of the different equilibrium phases at high temperatures at the Bi2O3-rich region of the ZnO-Bi2O3 will allow a correct understanding of the microstructural development. Equilibrium phases have been analyzed by XRD, SEM and DTA. Different temperature treatments of samples formulated in the Bi2O3 rich region of the ZnO-Bi2O3 binary system have allowed to determine the phase 19Bi2O3•ZnO as the equilibrium one instead of the 24Bi2O3•ZnO phase.Los materiales cerámicos basados en el sistema binario ZnO-Bi2O3 tienen su principal aplicación en el campo de los varistores. El sistema binario ZnO-Bi2O3 resulta especialmente relevante para la formación de la microestructura funcional de varistores. La determinación de las diferentes fases en equilibrio a alta temperatura en la región rica en Bi2O3 en el sistema binario ZnO-Bi2O3 permitirá interpretar correctamente el desarrollo microestructural. El estudio de las fases en equilibrio se ha llevado a cabo mediante difracción de rayos X, microscopía electrónica de barrido (MEB y análisis térmico diferencial (ATD. Tratamientos a diferentes temperaturas, en la zona rica en Bi2O3 del sistema, han permitido determinar la presencia del compuesto 19Bi2O3•ZnO como fase estable en equilibrio, en lugar del compuesto 24Bi2O3•ZnO.

Relación estructura-propiedades en aleaciones inteligentes con memoria de forma Cu-Al-Ag de alta temperatura de transformación martensítica termoelástica

Directory of Open Access Journals (Sweden)

Guilemany, J. M.

1998-05-01

Full Text Available New shape memory alloys have been developed in the last few years with high martensitic transformation temperatures. However, the highest martensitic transformation temperatures are lower than 200°C and they are achieved with very complex alloys. New Cu-Al-Ag shape memory alloys have been developed with martensitic transformation temperatures ranging from 250 to 400°C. It is really interesting to increase the knowledge of the phase stability behaviour when cycling the alloy above or below the martensitic transformation temperature because of the high temperatures involved. Two Cu-Al-Ag shape memory alloys with very different composition have been thermal cycled in a DSC following the amount of energy release during the forward and reverse transformation and the changes of the martensitic transformation temperatures in order to follow the phase changes that takes place during cycling.

En los últimos años, se han desarrollado nuevas aleaciones con memoria de forma, de altas temperaturas de transformación martensítica. Sin embargo, las temperaturas de transformación martensítica más elevadas son inferiores a 200°C e implican aleaciones de gran complejidad. Nuevas aleaciones con memoria de forma Cu-Al-Ag han sido desarrolladas con temperaturas de transformación entre 250 y 400°C. Es de gran importancia incrementar el conocimiento de la estabilidad de las fases durante el ciclado por encima o por debajo de la temperatura de transformación martensítica a causa de las altas temperaturas involucradas. Dos aleaciones con memoria de forma Cu-Al-Ag con muy diferente composición química han sido cicladas en el DSC midiendo la cantidad de energía liberada durante las transformaciones directa e inversa, así como los cambios en las temperaturas de transformación, con objeto de caracterizar las transformaciones de fase que tienen lugar durante el ciclado.

Estudio dieléctrico de cerámicas de textura y microestructura controladas con composiciones (SrBi2Nb2O91-x(Bi3TiNbO9x

Directory of Open Access Journals (Sweden)

Pardo, L.

2002-02-01

Full Text Available Ceramics of composition (SrBi2Nb2O91-x(Bi3TiNbO9x with x = 0.35, 0.65 and 1.00 and Aurivillius type structure have been prepared by natural sintering and hot pressing. Amorphous precursors were obtained by mechanochemical activation of stoichiometric mixtures of oxides and carbonates, which allows using moderate processing temperatures. These materials are interesting for their use as high temperature piezoelectrics. Dielectric characterisation allows to know the temperature at what takes place the ferro-paraelectric transition, which limits the working temperature of the material. It also gives information on how the electric properties, especially the d. c. conductivity, affect the polarizability of the ceramics. The properties relation with the microstructure and the texture is studied. In this work, dielectric studies of these materials have been made, in the frequency interval from 100 Hz to 5 MHz and in the temperature range from 200 ºC up to the ferroparaelectric transition temperatures (>900 ºC for Bi3TiNbO9.Se han preparado cerámicas de la solución sólida (SrBi2Nb2O91-x(Bi3TiNbO9x con x = 0.35, 0.65 y 1.00 y estructura tipo Aurivillius obtenidas por sinterización natural y por prensado en caliente. Se parte de precursores amorfos obtenidos por activación mecanoquímica de una mezcla estequiométrica de óxidos y carbonatos, lo que permite utilizar temperaturas moderadas de procesado. Estos materiales son interesantes por su posible uso como piezoeléctricos de alta temperatura. La caracterización dieléctrica permite establecer a qué temperatura se encuentra la transición ferro-paraeléctrica que limita la temperatura de uso del material y como afectan las propiedades eléctricas, especialmente la conductividad d. c., a la polarizabilidad de las cerámicas, así como su relación con su microestructura y textura. En este trabajo se ha realizado el estudio dieléctrico de estos materiales en el intervalo de frecuencias de 100

Effect of dc field on ac-loss peak in a commercial Bi:2223/Ag tape

Science.gov (United States)

Öztürk, Ali; Düzgün, İbrahim; Çelebi, Selahattin

2017-12-01

Measurements of the ac susceptibility in a commercial Bi:2223/Ag tape for some different ac magnetic field amplitudes, Hac, in the presence of bias magnetic field Hdc directed along Hac are reported. It is found that the peak values of the imaginary component of ac susceptibility χ″max versus Hac trace a valley for the orientation where applied field Ha perpendicular to wide face of the tape total. We note that the observation of the valley depends on various parameters such as field dependence parameter n in the critical current density, in the simple power law expression jc = α(T)/Bn, choice of the bias field Hdc together with selected ac field amplitudes Hac, and dimension and geometry of sample studied. Our calculations based on critical state model with jc = α(1 - T/Tcm)p/Bn using the fitting parameters of n = 0.25, p = 2.2, Tcm = 108 K gives quite good results to compare the experimental and calculated curves.

Evidence for charge transfer in Bi-based superconductors studied by positron annihilation

International Nuclear Information System (INIS)

Tang, Z.; Wang, S.J.; Gao, X.H.; Ce, G.C.; Zhao, Z.X.

1993-01-01

We have measured Doppler-broadening annihilation radiation (DBAR) spectra and positron lifetimes in normal and superconducting states for three kinds of Bi-based superconductors: Bi2212, Pb-doped Bi2223, Pb- and F-doped Bi2223. The difference spectra after deconvolution between two states show a sharpening effect with increasing temperature; the F-doped sample has the greatest amplitude in difference spectra but nearly the same positron lifetimes as the Pb-doped sample. The results are interpreted in terms of charge transfer between the Cu-O and Bi-O planes. The role of oxygen defects in charge transfer is discussed. (orig.)

Sample-length dependence of the critical current of slightly and significantly bent-damaged Bi2223 superconducting composite tape

International Nuclear Information System (INIS)

Ochiai, S; Fujimoto, M; Okuda, H; Oh, S S; Ha, D W

2007-01-01

The local critical current along a sample length is different from position to position in a long sample, especially when the sample is damaged by externally applied strain. In the present work, we attempted to reveal the relation of the distribution of the local critical current to overall critical current and the sample-length dependence of critical current for slightly and significantly damaged Bi2223 composite tape samples. In the experiment, 48 cm long Bi2223 composite tape samples, composed of 48 local elements with a length of 1 cm and 8 parts with a length 6 cm, were bent by 0.37 and 1.0% to cause slight and significant damage, respectively. The V-I curve, critical current (1 μV cm -1 criterion) and n value were measured for the overall sample as well as for the local elements and parts. It was found that the critical current distributions of the 1 cm elements at 0.37 and 1.0% bending strains are described by the three-parameter- and bimodal Weibull distribution functions, respectively. The critical current of a long sample at both bending strains could be described well by substituting the distributed critical current and n value of the short elements into the series circuit model for voltage generation. Also the measured relation of average critical current to sample length could be reproduced well in the computer by a Monte Carlo simulation method. It was shown that the critical current and n value decrease with increasing sample length at both bending strains. The extent of the decrease in critical current with sample length is dependent on the criterion of the critical current; the critical current decreases only slightly under the 1 μV cm -1 criterion which is not damage-sensitive, while it decreases greatly with increasing sample length under damage-sensitive criteria such as the 1 μV one

Fibras de polipropileno e sua influência no comportamento de concretos expostos a altas temperaturas: revisão Polypropylene fibers and their influence on the behavior of concretes exposed to high temperatures: review

Directory of Open Access Journals (Sweden)

A. L. de Castro

2011-03-01

Full Text Available A resistência ao fogo de um elemento estrutural de concreto é avaliada pelo intervalo de tempo em que o elemento continua a desempenhar suas funções sob condições de alta temperatura. Normalmente acredita-se que o concreto tem uma excelente durabilidade frente à ação do fogo, entretanto, na prática, a estabilidade desse material é prejudicada pelas altas temperaturas e os elementos de concreto têm apresentado danos excessivos ou mesmo rupturas catastróficas sob tais condições. Quando expostos às altas temperaturas, materiais à base de cimento sofrem mudanças físico-químicas que prejudicam suas propriedades mecânicas e comprometem sua resistência à transferência de calor. Embora as características térmicas de um concreto de alta resistência sejam semelhantes aos de um concreto convencional, este material possui uma maior sensibilidade às altas temperaturas devido à sua porosidade reduzida, apresentando uma maior perda relativa das propriedades mecânicas e a ocorrência do lascamento explosivo na faixa de temperatura entre 100 ºC e 400 ºC. O lascamento pode ser evitado pela introdução de fibras de polipropileno na composição do concreto: quando fundidas e parcialmente absorvidas pela matriz de cimento, as fibras criam uma rede de canais permeável que permite a migração dos gases para o exterior, reduzindo a pressão nos poros do material e, conseqüentemente, eliminando a possibilidade de ocorrência do lascamento explosivo. Assim, no presente artigo, uma revisão sobre o comportamento de concretos expostos às altas temperaturas, bem como a influência da fibra de polipropileno sobre este comportamento foi realizada, direcionando-se para os concretos aplicados na construção civil.The fire resistance of a structural concrete is evaluated by the time length that the element keeps performing its functions under high temperature conditions. It is usually believed that the concrete has an excellent durability

Mechanism of Pb and Sb role on the 2223 phase of BSCCO system superconductor

Energy Technology Data Exchange (ETDEWEB)

Sukirman, E; Sulisworo, P; Prasuad, W; Wuryanto, [Material Science Research Centre, National Atomic Energy Agency, Kawasan Puspiptek Serpong Tangerang (Indonesia)

1998-10-01

The mechanism of Pb and Sb role on the 2223 phase of Bi-Sr-Ca-Cu-O (BSCCO) system superconductor has been investigated. The 2223 phase samples without doping and with doping: Pb, and Sb have been synthesized by solid state reaction method. The samples characterization have been carried out through a susceptibility-, resistivity-, neutron diffraction profile-, and microstructure measurements. Crystal structure of the samples have been analyzed using RIETAN software. The analysis results show that relative content of the 2223 phase increase from 28% in the non-doped sample (TDP) to 75% in Pb-doped (DPB) and 44% in Sb-doped (DSB) samples. When, Pb, or Sb enter into the 2223 phase crystal system, then the oxygen atoms on SrO layers shift toward the copper atoms position on Cu(2)O{sub 2} layers as far as 0.1(1) and 0.1(1) A in DPB, and DSB, respectively. BiO layers shift away from SrO layers as far as 0.3(1) and 0.1(1) A in DPB, and DSB, respectively. The critical current density Jc increase from 3 A/cm{sup 2} in TDP to 210 and 35 A/cm{sup 2} in DPB, and DSB, respectively. The onset point of Tc also increase from 99 K in TDP to 103 and 107 K in DPB and DSB, respectively. It is concluded that the enhancement of the 2223 phase, Jc and onset point are due to improvement on the structure stability, improvement on the connection between unit-cells, and shortening the apical oxygen-Cu chains, respectively. (author)

Mathematical model of voltage-current characteristics of Bi(2223)/Ag magnets under an external magnetic field

CERN Document Server

Pitel, J; Lehtonen, J; Kovács, P

2002-01-01

We have developed a mathematical model, which enables us to predict the voltage-current V(I) characteristics of a solenoidal high-temperature superconductor (HTS) magnet subjected to an external magnetic field parallel to the magnet axis. The model takes into account the anisotropy in the critical current-magnetic field (I sub c (B)) characteristic and the n-value of Bi(2223)Ag multifilamentary tape at 20 K. From the power law between the electric field and the ratio of the operating and critical currents, the voltage on the magnet terminals is calculated by integrating the contributions of individual turns. The critical current of each turn, at given values of operating current and external magnetic field, is obtained by simple linear interpolation between the two suitable points of the I sub c (B) characteristic, which corresponds to the angle alpha between the vector of the resulting magnetic flux density and the broad tape face. In fact, the model is valid for any value and orientation of external magneti...

Statistical analysis of the distribution of critical current and the correlation of n value to the critical current of bent Bi2223 composite tape

International Nuclear Information System (INIS)

Ochiai, S; Matsubayashi, H; Okuda, H; Osamura, K; Otto, A; Malozemoff, A

2009-01-01

Distributions of local and overall critical currents and correlation of n value to the critical current of bent Bi2223 composite tape were studied from the statistical viewpoint. The data of the local and overall transport critical currents and n values of the Bi2223 composite tape specimens were collected experimentally for a wide range of bending strain (0-1.1%) by using the specimens, designed so as to characterize the local and overall critical currents and n values. The measured local and overall critical currents were analyzed with various types of Weibull distribution function. Which of the Weibull distribution functions is suitable for the description of the distribution of local and overall critical currents at each bending strain, and also how much the Weibull parameter values characterizing the distribution vary with bending strain, were revealed. Then we attempted to reproduce the overall critical current distribution and correlation of the overall n value to the overall critical current from the distribution of local critical currents and the correlation of the local n value to the local critical current by a Monte Carlo simulation. The measured average values of critical current and n value at each bending strain and the correlation of n value to critical current were reproduced well by the present simulation, while the distribution of critical current values was reproduced fairly well but not fully. The reason for this is discussed.

Comportamiento mecánico a alta temperatura de cerámicas de nitruro de silicio

Directory of Open Access Journals (Sweden)

Meléndez-Martínez, J. J.

2001-04-01

Full Text Available The high temperature mechanical behaviour of two silicon nitride-based ceramic materials has been studied: N 7202, made by low pressure sintering with yttria, alumina and magnesia as additives, and N 3208, made by high pressure sintering with yttria and alumina as additives. Both materials are β-silicon nitride. The results have been analysed in terms of the classical creep equation. The stress exponent was n = 0.4 for N 7202 and n = 0.5 for N 3208, whereas the average apparent activation energy was Q ≈ 500 kJ/mole for both materials.Transmission electron microscopy studies have allowed to determine the microstructural features of these materials.

Se ha estudiado el comportamiento mecánico a alta temperatura de dos materiales cerámicos a base de nitruro de silicio: N 7202, fabricado por sinterizado a baja presión con ytria, alúmina y magnesia como aditivos y N 3208, fabricado por sinterizado a alta presión con ytria y alúmina como aditivos. En ambos casos, se trata de nitruro de silicio en fase β. Los resultados han sido analizados mediante la ecuación clásica de fluencia. El exponente de tensión fue n = 0,4 para N 7202 y n = 0,5 para N 3208, mientras que la energía de activación aparente promedio es Q ≈ 500 kJ/mol para ambos materiales. Estudios de microscopía electrónica de transmisión han permitido determinar las características microestructurales de estos materiales.

Níveis de proteína bruta para leitoas dos 30 aos 60 kg mantidas em ambiente de alta temperatura (31ºC

Directory of Open Access Journals (Sweden)

Orlando Uislei Antonio Dias

2001-01-01

Full Text Available O experimento foi conduzido para avaliar níveis de proteína bruta (PB para leitoas em crescimento, mantidas em ambiente de alta temperatura. A temperatura interna da sala foi mantida em 30,7 ± 0,61°C; a umidade relativa, em 66,4 ± 7,7%; e o índice de temperatura de globo e umidade (ITGU foi calculado em 81,1 ± 1,36. Foram utilizadas 40 leitoas mestiças, com peso inicial médio de 29,7 ± 1,60 kg, em delineamento de blocos ao acaso com cinco tratamentos (16, 17, 18, 19 e 20% de PB, quatro repetições e dois animais por unidade experimental. As rações experimentais isoenergéticas (3400 kcal de ED/kg de ração foram formuladas para satisfazer as exigências dos animais, exceto em PB. Ração e água foram fornecidas à vontade até o final do experimento, quando os animais atingiram peso médio de 60,0 ± 1,93 kg. Os tratamentos não influenciaram o ganho de peso. Entretanto, a conversão alimentar melhorou de forma quadrática até o nível de 18,26%. Os consumos diários de proteína e lisina aumentaram linearmente em razão do nível de PB da ração, porém não se observou efeito dos tratamentos sobre os consumos de ração e de energia digestível diários. A taxa de deposição diária de gordura (TDG na carcaça variou de forma quadrática, reduzindo até o nível de 19,48% de PB, enquanto a de proteína (TDP aumentou de forma linear. Apesar dos efeitos quadrático e linear dos tratamentos sobre a TDG e a TDP, respectivamente, o modelo "Linear Response Plateau" (LRP foi o que melhor se ajustou aos dados, estimando-se em 18,38 e 18,12% os níveis de PB, a partir dos quais a TDG e a TDP permaneceram em um platô. Leitoas em crescimento, mantidas em ambiente de alta temperatura, exigem 18,26% de PB na ração para melhor desempenho e composição de carcaça.

Phase chemistry and microstructure evolution in silver-clad (Bi2-xPbx)Sr2Ca2Cu3Oy filaments

International Nuclear Information System (INIS)

Luo, J.S.; Merchant, N.; Maroni, V.A.; Escorcia-Aparicio, E.; Gruen, D.M.; Tani, B.S.; Riley, G.N. Jr.; Carter, W.L.

1992-08-01

The reaction kinetics and mechanism that control the conversion of (Bi,Pb) 2 Sr 2 CaCu 2 O z (Bi-2212) + alkaline earth cuporates to (Bi, Pb) 2 Sr 2 Ca 2 Cu 3 O y (Bi-2223) in silver-clad wires were investigated as a function of equilibration temperature and time at a fixed oxygen partial pressure (7.5% O 2 ). Measured values for the fractional conversion of Bi-2223 versus time have been evaluated based on the Avrami equation. SEM and TEM studies of partially and fully converted wires have revealed that (1) the growth of Bi-2223 is two-dimensional and controlled by a diffusion process, (2) liquid phases are present during part of the Bi-2212 -> Bi-2212 conversion, and (3) segregation of the second phases occurs in early time domains of the reaction

Caracterización y propiedades mecánicas a alta temperatura de un acero inoxidable dúplex

Directory of Open Access Journals (Sweden)

Jiménez, J. A.

1998-05-01

Full Text Available The microstructure and mechanical behavior at high temperature of a thermomechanical processed duplex stainless steel have been studied. Recrystalization of the material takes place during heating to test temperature, and a microstructure consisting of islands of austenitic grains of about 10-15 μm in size included in a more or less continuous matrix of ferrite is observed. Tensile tests at temperatures above 1,000°C and at low strain rates show a stress exponent of about 2 and elongations to failure up to 290 %. These values suggest that deformation is controlled by a grain boundary sliding mechanism, which causes a decrease in the size of the islands during deformation. Finally, an activation energy for plastic deformation of 167 kJ/mol was observed that was related to the activation energy for grain boundary diffusion of iron.

Se ha estudiado la microestructura y el comportamiento mecánico a alta temperatura de un acero inoxidable dúplex procesado termomecánicamente. Durante el calentamiento a la temperatura de ensayo, el material recristaliza y se obtiene una microestructura de granos austeníticos de tamaños comprendidos entre 10 y 15 μm agrupados en islas incluidas en una matriz más o menos continua de ferrita. Ensayos de tracción a temperaturas superiores a 1.000°C y bajas velocidades de deformación muestran un exponente de la tensión igual a 2 y alargamientos a rotura de hasta 290 %. Estos valores permiten asociar el mecanismo de deformación al deslizamiento de fronteras de grano, el cual determina la desaparición progresiva de las islas de granos austeníticos durante la deformación. Finalmente, se encontró un valor de 167 kJ/mol para la energía de activación de la deformación plástica, la cual se relacionó con la energía de autodifusión del hierro a lo largo de las fronteras de grano.

Conceptual design of a forced-flow-cooled 20-kA current lead using Ag-alloy-sheathed Bi-2223 high-temperature superconductors

International Nuclear Information System (INIS)

Heller, R.

1994-11-01

The use of high-temperature superconductors in current leads to reduce refrigeration power has been investigated by many groups in the past. Most used YBCO and Bi-2212 bulk superconductors, although their critical current density is not very high. In this paper, BI-2223 HTSC tapes sheathed with Ag alloys are used in the design of a 20-kA current lead because of their higher critical current in medium magnetic fields. The lead current of 20 kA is related to the coil current of the planned stellarator WENDELSTEIN 7-X. Forced-now helium cooling has been used in the design, allowing position-independent and well-controlled operation. The design characteristics of the lead are presented and 4-K helium cooling of the whole lead, as well as 60-K helium cooling of the copper part of the lead, is discussed. The power consumption at zero current, and the lead's behaviour in case of loss of coolant flow, are given, The results of the design allow extrapolation to current leads of the 50-kA range

(Bi, Pb).sub.2, Sr.sub.2 Ca.sub.2 Cu.sub.3 O.sub.x superconductor and method of making same utilizing sinter-forging

Science.gov (United States)

Chen, Nan; Goretta, Kenneth C.; Lanagan, Michael T.

1998-01-01

A (BiPb).sub.2 Sr.sub.2 Ca.sub.2 Cu.sub.3 O.sub.x (Bi223) superconductor with high J.sub.c, phase purity, density and mechanical strength is formed from Bi2223 powder which is synthesized from a mixture of Bi.sub.2 O.sub.3, PbO, SrCO.sub.3, CaCo.sub.3 and CuO. The mixture is milled, then dried and calcined to synthesize the Bi2223 powder with the desired phase purity. The calcination is performed by heating the dried mixture for 50 hours at 840.degree. C. The partially synthesized powder is then milled for 1-4 hours before calcining further for another 50 hours at 855.degree. C. to complete the synthesis. After calcination, the Bi2223 powder is cold pressed to a predetermined density and sinter forged under controlled temperature and time to form a Bi2223 superconductor with the desired superconducting properties.

(Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} superconductor and method of making same utilizing sinter-forging

Science.gov (United States)

Chen, N.; Goretta, K.C.; Lanagan, M.T.

1998-10-13

A (BiPb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x}(Bi223) superconductor with high J{sub c}, phase purity, density and mechanical strength is formed from Bi2223 powder which is synthesized from a mixture of Bi{sub 2}O{sub 3}, PbO, SrCO{sub 3}, CaCo{sub 3} and CuO. The mixture is milled, then dried and calcined to synthesize the Bi2223 powder with the desired phase purity. The calcination is performed by heating the dried mixture for 50 hours at 840 C. The partially synthesized powder is then milled for 1--4 hours before calcining further for another 50 hours at 855 C to complete the synthesis. After calcination, the Bi2223 powder is cold pressed to a predetermined density and sinter forged under controlled temperature and time to form a Bi2223 superconductor with the desired superconducting properties. 5 figs.

Crecimiento y caracterización de monocristales superconductores de alta temperatura crítica

Directory of Open Access Journals (Sweden)

L. T. Corredor

2003-07-01

Full Text Available En este trabajo se presenta, detalladamente, el procedimiento para la implementación de la técnica de auto-flujo para el crecimiento de monocristales superconductores de alta temperatura crítica. Fueron producidos monocristales de las familias YBa2Cu3O7-δ y CaLaBaCu3O7-δ mediante dicha técnica. El carácter superconductor de los mismo se corroboró a través de mediciones de resistividad eléctrica y susceptibilidad magnética AC. Las características cristalográficas y morfológicas se estudiaron por medio de difracción de rayos X y microscopía electrónica de barrido (SEM, microscopía metalográfica y análisis de rayos X por dispersión de energía (EDX respectivamente. Los resultados de estas caracterizaciones muestran que todos los monocristales superconductores de YBa2Cu3O7-δ son de excelente calidad. Adicionalmente, se obtuvo una muestra de la composición de CaLaBaCu3O7-δ con buenas propiedades morfolóficas, lo cual evidenció crecimiento orientado en los planos (h k 0.

Variation of local critical current and its influence on overall current of bent multifilamentary Bi2223/Ag tape

International Nuclear Information System (INIS)

Ochiai, S.; Doko, D.; Rokkaku, H.; Fujimoto, M.; Okuda, H.; Hojo, M.; Tanaka, M.; Sugano, M.; Osamura, K.; Mimura, M.

2006-01-01

The correlation between the local and overall currents in a multifilamentary Bi2223/Ag/Ag alloy composite tape under bending strain was studied. The correlation of the measured distributed local critical current and n-value to overall critical current was described comprehensively with a voltage summation model that regards the overall sample to be composed of a series circuit. The analysis of the measured critical current and n-value revealed that the distribution of local critical current could be described with the Weibull distribution function and the n-value could be expressed as a function of critical current as a first approximation. By combining the Weibull distribution function of the local critical current, the empirical formula of the n-value as a function of critical current, voltage summation model and Monte Carlo method, the overall current and n-value could be predicted fairly well from those of local elements

The influence of tensile strain to critical current of Bi2223 composite tape

International Nuclear Information System (INIS)

Mukai, Y.; Shin, J.K.; Ochiai, S.; Okuda, H.; Sugano, M.; Osamura, K.

2008-01-01

As the stress-induced damage evolution is different from position to position in the sample, the local critical current is scattered in a sample, affecting on the overall current. The present work aimed to describe the distribution of local critical current and its relation to overall critical current under tensile stress for Bi2223/Ag superconducting composite tape. In the experiment, seven voltage probes were attached in a step of 10 mm. The local critical current and n-value at 77 K under various applied stress levels were measured for a voltage probe distance 10 mm and the overall ones for a probe distance 60 mm. Main results are summarized as follows. The overall critical current and n-value were described well by using the voltage summation model in which the sample was regarded as a one dimensional series circuit. For the low applied stress, the distribution of local critical current was described with the three parameter Weibull distribution function. Using the measured distribution of the local critical current, an experimental relation of critical current to n-value and the voltage summation model, and applying the Monte Carlo method, the overall critical current was predicted, which was in good agreement with the experimental results. Based on these results, the sample length dependence of critical current of the sample damaged by tensile stress was discussed

Un procedimiento para separar, a alta temperatura, la fase líquida del clínker de los sólidos a los que impregna

Directory of Open Access Journals (Sweden)

Ruiz de Gauna, Ángel

1979-12-01

Full Text Available Not avaible

Según se ha ido profundizando en el conocimiento del mecanismo de formación de los silicatos cálcicos hidráulicamente activos del cemento portland, se ha ido poniendo de relieve la gran importancia que la composición de la fase líquida del clínker tiene, tanto en la temperatura y velocidad de formación de aquéllos, como en sus características hidráulicas incluyéndose en ellas las mecánico-resistentes. En las propiedades tecnológicas del cemento resultante influye también directamente la composición que a alta temperatura tiene la fase líquida, por cuanto de ella depende su aptitud a la cristalización, y la clase y propiedades de los componentes secundarios que cristalizan en el curso del enfriamiento y son de decisiva influencia en propiedades tan importantes como la velocidad de fraguado y estabilidad de volumen.

Mate (chimarrão é consumido em alta temperatura por população sob risco para o carcinoma epidermóide de esôfago

Directory of Open Access Journals (Sweden)

BARROS Sérgio Gabriel Silva de

2000-01-01

Full Text Available Introdução -- O mate, ou chimarrão, uma infusão popular de uma erva (Ilex paraguayensis bebida em grandes volumes, é um conhecido fator de risco para carcinoma epidermóide de esôfago e há suspeitas de que a água quente utilizada para o consumo possa ser fator importante na carcinogênese. Métodos - Pesquisou-se a temperatura em que a infusão é ingerida por uma amostragem da população sob risco para carcinoma epidermóide de esôfago. Realizaram-se entrevistas com indivíduos consumidores de mate na área urbana de Taquara, RS, com relação aos hábitos de ingestão de mate, e a temperatura do mate foi medida através de termômetros de precisão. A percepção da temperatura, estimada pelos usuários, foi também registrada. Resultados - Em 36 residências, 107 pessoas estavam ingerindo mate. A maioria bebia a infusão diariamente (97,2% e o consumo médio diário foi de 1.265 mL por usuário (desvio padrão de 1.132 mL, variando de 250 a 6.000 mL. A temperatura medida era igual ou superior a 60 º C em 72% das residências, com média de 63,4 º C (51-78 º C e mediana de 64,4 º C. Conclusão - Neste estudo foi possível evidenciar que o mate é consumido em grandes volumes e alta temperatura e que os usuários não foram capazes de estimar corretamente a temperatura do mate consumido. A temperatura elevada do mate consumido nessa população pode estar contribuindo à carcinogênese esofágica.

Mechanical properties of Bi,Pb(2223) single filaments and Ic(ε) behaviour in longitudinally strained tapes

International Nuclear Information System (INIS)

Passerini, Reynald; Dhalle, Marc; Seeber, Bernd; Fluekiger, Rene

2002-01-01

The Young's modulus and fracture stress of isolated Bi,Pb(2223) filaments were deduced from three-point bending tests performed at different stages of the tapes preparation. These results were introduced in the model describing the evolution of critical current of tapes submitted to a longitudinal strain in view to predict their irreversible strain limit ε irr . These calculated irreversible strain limits were compared to measured values, taken from a set of tapes made with different filling factors and composite matrices. This experiment shows that the predicted irreversible strain limits correspond to the measured ones. Presenting the I c behaviour of highly stressed tapes in a magnetic field, we discuss the evolution of the ratio I strong c0 /I c0 versus strain. This value, representative of the fraction of the critical current attributed to strongly connected grains, increases significantly during the crack formation regime at ε > ε irr . This indicates that mechanically weak links correspond to electromagnetically weak ones. This result is further confirmed by comparing the modulus of rupture obtained in single filaments extracted from tapes with different I c values

Experimental and numerical study of influence of ferromagnetic cover on critical current of BiSCCO-2223/Ag tape superconductor

International Nuclear Information System (INIS)

Vojenciak, M; Souc, J; Goemoery, F

2009-01-01

Samples of commercially available BiSCCO-2223/Ag tape have been partially covered by the ferromagnetic material. Improvement of the self-field critical current up to 15 % has been achieved by this procedure. A critical current of such tape strongly depends on geometric and magnetic properties of both, the superconducting tape as well as the ferromagnetic cover. Numerical simulations, based on the critical state model using commercial finite element method (FEM) code, have been performed. Properties of superconductor are characterized by anisotropic dependence of the critical current density on magnetic field as well as detail geometry of filaments. The ferromagnetic material is characterized by nonlinear magnetization curve. Nonlinear dependences of the critical current on selected parameters are shown in this work. Optimization of the cover parameters using these curves has been made. Samples with various parameters have been manufactured for the confirmation of numerical simulations results. Experimental results are in good qualitative agreement with results obtained by numerical simulations.

Mechanical properties of Bi,Pb(2223) single filaments and I sub c (epsilon) behaviour in longitudinally strained tapes

CERN Document Server

Passerini, R; Seeber, B; Flükiger, R

2002-01-01

The Young's modulus and fracture stress of isolated Bi,Pb(2223) filaments were deduced from three-point bending tests performed at different stages of the tapes preparation. These results were introduced in the model describing the evolution of critical current of tapes submitted to a longitudinal strain in view to predict their irreversible strain limit epsilon sub i sub r sub r. These calculated irreversible strain limits were compared to measured values, taken from a set of tapes made with different filling factors and composite matrices. This experiment shows that the predicted irreversible strain limits correspond to the measured ones. Presenting the I sub c behaviour of highly stressed tapes in a magnetic field, we discuss the evolution of the ratio I sup s sup t sup r sup o sup n sup g sub c sub 0 /I sub c sub 0 versus strain. This value, representative of the fraction of the critical current attributed to strongly connected grains, increases significantly during the crack formation regime at epsilon >...

Effect of lead content on nonstoichiometric Bi2-xPbySr2Ca2Cu3Oδ ceramic superconductors

International Nuclear Information System (INIS)

Diaz-Valdes, E.; Pacheco-Malagon, G.; Contreras-Puente, G.; Mejia-Garcia, C.; Andrade-Garay, G.; Ortiz-Lopez, J.; Conde-Gallardo, A.; Falcony, C.

1993-01-01

Ceramic superconducting samples of the type Bi 2-x Pb y Sr 2 Ca 2 Cu 3 O δ were processed with a nonstoichiometric content of Bi and Pb (x≠y) with respect to the 2223 phase in this system. The resistance vs. temperature characteristics and the presence of the 2223 and 2212 phases as a function of the sample preparation conditions and the lead content (Bi/Pb ratio) are reported. The growth of unwanted phases such as PbO was observed for those samples with a high content of Pb (y=0.9) and Bi (x=0.1). (orig.)

Fricción interna en plomo de muy alta pureza (99,9999% a temperaturas medias

Directory of Open Access Journals (Sweden)

Gallego, I.

2001-04-01

Full Text Available Internal friction spectra of high purity lead (99.9999% at medium temperatures exhibit a main relaxation peak at 230 K (P₁ which depends strongly on the dislocation arrangement. The mechanism associated to P₁ relaxation has an activation area between 500b² and 2000b² and its activation energy is 0.65±0.05 eV (63±5 KJ/mol, which is only 0,6 times the autodiffusion energy of lead. The behaviour of P₁ peak and its dependence on thermomechanical treatments has allowed us to conclude that it is associated to the sliding of dislocations controlled by the climbing of jogs by diffusion of vacancies along the dislocation lines. At a slightly higher temperature, another relaxation (P₁ turns up in the spectra, which can be associated to different mechanisms.

El espectro de fricción interna, a medias temperaturas, del plomo de muy alta pureza (99,9999% presenta una relajación principal a 230 K (P₁, cuya intensidad depende fuertemente del estado de organización de las dislocaciones. La medida de los parámetros de activación de P₁ indica que el mecanismo asociado a esta relajación tiene un área de activación comprendida entre 500b² y 2.000b² y un valor de la energía de activación de 0,65 ±0,05 eV (63±5 KJ/mol, que es sólo 0,6 veces la energía de autodifusión del plomo. El comportamiento de esta relajación y su dependencia con los tratamientos termomecánicos, nos ha permitido concluir que P₁ está originado por el deslizamiento de dislocaciones controlado por la escalada de escalones a lo largo de la línea de dislocación. A temperaturas ligeramente superiores, aparece otra relajación (P₁, cuyo origen puede estar ligado a diferentes mecanismos.

Potential barrier behavior in BiCuVOX materials Comportamento da barreira de potencial em materiais BiCuVOX

Directory of Open Access Journals (Sweden)

S. M. Gheno

2011-12-01

Full Text Available The BiMeVOX materials appear being high attractive for applications at low temperatures when the ionic conductivity is the determining parameter. The occurrence of many types substitution was confirmed for numerous Me ions, but the greatest interest have been focused on the BiCuVOX materials. The objective of this study was to image the potential barriers in BiCuVOX. The sample was sintered for 4 h at 750 °C and the results show that the high density compound can be obtained. Simultaneously, topography and electric force microscopy (EFM images are viewed side-by-side. EFM experiments were performed and the results show the maps of the electric field distribution on the surface of BiCuVOX. The formation of potential barrier was observed and the width and intensity were measured.Materiais do tipo BiMeVOX são muito atrativos para aplicações em baixas temperaturas quando a condutividade iônica for o parâmetro determinante. A ocorrência de muitos tipos de substituições foi confirmada para numerosos íons Me, dentre os quais, existe um grande interesse no estudo de materiais BiCuVOX. O objetivo deste estudo foi realizar o imageamento das barreiras de potencial em uma amostra de material BiCuVOX. A amostra foi sinterizada 4 h a 750 °C e apresentou alta densidade. Imagens da superfície topográfica e de microscopia de força elétrica (EFM foram obtidas simultaneamente em um microscópio de varredura por sonda. Os experimentos EFM mostraram um mapa da distribuição do campo elétrico na superfície do material BiCuVOx. A formação da barreira de potencial foi observada e tanto a largura quanto a altura foram medidas.

Comportamiento plástico a alta temperatura de Al2O3 codopado con CuO y TiO2 fabricado por reacción

Directory of Open Access Journals (Sweden)

Domínguez-Rodríguez, A.

2003-08-01

Full Text Available The high temperature plastic behavior of reaction-bonded alumina doped with equimolar amounts of copper and titanium oxides (CuO and TiO2, respectively has been studied by means of creep and stress relaxation tests in air. Deformation results have been correlated with microstructural observations and X-ray diffraction studies in order to deduce the mechanism responsible for the deformation. This material exhibits plasticity at temperatures as low as 950ºC in contrast with other aluminas. At temperatures near 1000ºC a linear relation between the strain rate and the stress has been detected (a stress exponent n equal to 1 but both above and below this temperature higher values of n have been observed.Se ha estudiado el comportamiento plástico a alta temperatura de alúmina codopada con cantidades equimolares de óxidos de cobre (CuO y titanio (TiO2 fabricada por reacción mediante el empleo de ensayos de fluencia y de relajación de tensiones en atmósfera de aire. Los resultados de los ensayos de deformación plástica han sido correlacionados con observaciones microestructurales y difracción de rayos X con vistas a deducir el mecanismo responsable del proceso de deformación. Este material presenta comportamiento plástico a temperaturas tan bajas como 950ºC en contraste con otras aluminas. A temperaturas alrededor de 1000ºC se ha observado una relación lineal entre la velocidad de deformación y la tensión (exponente de tensión igual a uno mientras que a temperaturas por encima y por debajo de este valor el exponente de tensión toma valores más elevados.

Mecanismos de movilidad de dislocaciones a temperaturas medias en plomo de muy alta pureza (99.9999 %

Directory of Open Access Journals (Sweden)

Gallego, I.

1998-05-01

Full Text Available The internal friction spectrum of high purity lead (99.9999 % at medium temperatures has been studied. A new peak (P₁ has been found at 240 K, which has not been studied up to now. The activation energy of the process associated with F, has been determined and its experimental behaviour has also been systematically studied. The comparison between the results and the theoretical predictions of the models of dislocation mobility allows us to attribute the P₁ peak to the sliding of dislocations, controlled by the climbing of jogs induced by the diffusion of vacancies along the dislocation line. This conclusion is analogue to that obtained in previous works for the P₁v peak in very high purity aluminium (99.9999 %.

Se ha realizado un estudio sistemático del espectro de fricción interna del plomo de muy alta pureza (99,9999 % a temperaturas medias, encontrándose un pico a 240 K (P₁ que no ha sido estudiado en la bibliografía hasta el momento. Los análisis mediante fricción interna nos han permitido evaluar la energía de activación del proceso ligado a P₁ y determinar el comportamiento de este pico en función de diversos parámetros. La comparación de los resultados experimentales con las predicciones teóricas de varios modelos microscópicos de movilidad de dislocaciones nos ha permitido concluir que el pico P₁ está asociado con el deslizamiento de dislocaciones controlado por la escalada de escalones mediante la difusión de vacantes a lo largo de, la línea de dislocación. Esta interpretación es análoga a la realizada en trabajos previos para el pico P₁ del aluminio de muy alta pureza (99,9999 %.

39 CFR 222.3 - Other delegation.

Science.gov (United States)

2010-07-01

... 39 Postal Service 1 2010-07-01 2010-07-01 false Other delegation. 222.3 Section 222.3 Postal Service UNITED STATES POSTAL SERVICE ORGANIZATION AND ADMINISTRATION DELEGATIONS OF AUTHORITY § 222.3 Other delegation. (a) Documentation. All delegations of authority must be officially documented. (b...

Propriedades Vibracionais da L-glutamina sob altas pressÃes e sob altas temperaturas.

OpenAIRE

Rocicler Oliveira Holanda

2010-01-01

Neste trabalho, cristais de l-glutamina (C5H10N2O3) foram submetidos à anÃlises atravÃs da tÃcnica de espectroscopia Raman. Inicialmente realizou-se uma identificaÃÃo tentativa de todas as bandas Raman e em uma segunda etapa obteve-se os espectros do material variando os parÃmetros termodinÃmicos de pressÃo hidrostÃtica e temperatura. A regiÃo espectral para os experimentos realizados em funÃÃo da pressÃo hidrostÃtica esteve entre 40 cm-1 e 3550 cm-1 e a variaÃÃo da pressÃo entre 0 GPa e 5,8...

Desarrollo y optimización de recubrimientos de superaleaciones con adición de cargas cerámicas y elementos reactivos obtenidos por proyección térmica para aplicaciones de resistencia a oxidación a alta temperatura y al desgaste

OpenAIRE

Cervera González, Iván

2011-01-01

El objetivo principal del presente trabajo es la obtención de recubrimientos con una composición optimizada para aplicaciones de elevada resistencia a alta temperatura y al desgaste, proyectados térmicamente sobre acero al carbono AISI 1110, mediante la técnica de oxifuel, basados en el sistema NiCrAlY/Al2O3. Estos recubrimientos deben ser capaces de proteger adecuadamente a un material de escasa resistencia mecánica y térmica para el rango de temperaturas analizado, que se sitúa entre 850 – ...

Materiales intermetálicos para aplicaciones estructurales a altas temperaturas

OpenAIRE

Adeva, Paloma

1999-01-01

La investigación en el campo de los materiales intermetálicos ha recibido un fuerte impulso a partir de los años 80 debido principalmente a las demandas por parte del sector aeronáutico, de materiales resistentes, tenaces y dúctiles a elevadas temperaturas que puedan sustituir a las superaleaciones.En este trabajo se analizan las propiedades más características de estos compuestos tales como la estructura ordenada, los elevados valores de límite elástico y resistencia a rotura,que mantienen h...

Role of vanadium in Bi-2223 ceramics

Indian Academy of Sciences (India)

Previous reports ([1–7] and also, [9]) on V-substituted samples of Bi2Sr2Ca2Cu3Os have mostly pointed out that V ... Two series of V-substituted samples were prepared by partial replacement of V at two different sites; viz. the ..... also evaluated the phase composition on the basis of our susceptibility plots. This has also.

Sputtering yields of YBa2Cu3O7 and Bi2Sr2Ca2Cu3O10 by 100 keV Ar+ impact at normal incidence

International Nuclear Information System (INIS)

Matsunami, N.

1998-01-01

The thickness change of YBa 2 Cu 3 O 7-δ (YBCO) and Bi 2 Sr 2 Ca 2 Cu 3 O 10-δ (Bi-2223) films by 100 keV Ar + impact at normal incidence has been measured using 1.8 MeV He Rutherford backscattering method. The sputtering yields of YBCO and Bi-2223 films are determined as 2.5 and 1.7 atoms per ion, respectively. A considerable segregation of Y is observed for YBCO by ion impact. Comparing the experimental sputtering yields with those of a computer simulation, the effective surface binding energies for the films of non-superconducting phase are obtained as 3.0 and 4.5 eV for YBCO and Bi-2223, respectively. These surface binding energies are compared with those of thermodynamics. (orig.)

The effect of heat treatment on the properties of (Bi,Pb)2Sr2Ca2Cu3Oδ

International Nuclear Information System (INIS)

Fetisov, A.V.; Yasnikov, A.G.; Fotiev, A.A.

1994-01-01

In synthesis of (Bi,Pb) 2 Sr 2 Ca 2 Cu 2 O δ (2-2-2-3 phase), which is known to belong to a homologous series of bismuth-based superconductors, several routes have been reported to date to yield materials with a high content, around 95% of the main phase. This phase is characterized by the highest superconducting-transition temperature T c among all known high-T c materials. Based on literature data, heat-treatment conditions are expected to affect strongly the T c of the 2-2-2-3 phase, as they do for other high-T c materials. An optimal oxygen content in 2-2-2-3 was presumed to be the deciding factor for attainment of high T c 's. However, heating below ∼ 870 K in air causes no change in oxygen content in the 2-2-2-3 phase. At the same time, it is oxidizing annealing at T c up to 105-110 K. The conclusions found that changes in oxygen content for (Bi,Pb) 2 Sr 2 Ca 2 Cu 2 O δ (2-2-2-3 phase) do not affect T c , which remains unchanged after shor anneals at 370-1020 Kelvin in different atmospheres. In order to obtain high T c 's, it will suffice to exclude long anneals at 1020-1090 Kelvin from the technology. For the 2-2-2-3 phase, a degradation process, which does not change the composition of the phase, is like that for YBa 2 Cu 3 O 6+delta . Proposed is that different structural planes participate in mass exhanage with an atmosphere: (BiO) planes which do not participate to superconductivity, participate in oxygen exchange; and H 2 O and CO 2 penetrate into the CuO 2 planes, which are responsible for superconductivity in the 2-2-2-3 phase

Pb solubility of the high-temperature superconducting phase Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+d}

Energy Technology Data Exchange (ETDEWEB)

Kaesche, S.; Majewski, P.; Aldinger, F. [Max-Planck-Institut fuer Metallforschung, Stuttgart (Germany)] [and others

1994-12-31

For the nominal composition of Bi{sub 2.27x}Pb{sub x}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+d} the lead content was varied from x=0.05 to 0.45. The compositions were examined between 830{degrees}C and 890{degrees}C which is supposed to be the temperature range over which the so-called 2223 phase (Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+d}) is stable. Only compositions between x=0.18 to 0.36 could be synthesized in a single phase state. For x>0.36 a lead containing phase with a stoichiometry of Pb{sub 4}(Sr,Ca){sub 5}CuO{sub d} is formed, for x<0.18 mainly Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub 8+d} and cuprates are the equilibrium phases. The temperature range for the 2223 phase was found to be 830{degrees}C to 890{degrees}C but the 2223 phase has extremely varying cation ratios over this temperature range. Former single phase 2223 samples turn to multi phase samples when annealed at slightly higher or lower temperatures. A decrease in the Pb solubility with increasing temperature was found for the 2223 phase.

Influencia de la temperatura sobre el crecimiento muscular de la lubina, Dicentrarchus labrax L., durante el desarrollo larvario

OpenAIRE

Ayala Florenciano, Mª Dolores

1999-01-01

En este trabajo se ha estudiado el efecto de la temperatura de incubación y cultivo sobre el desarrollo y el crecimiento muscular de lubina, Dicentrarchus labrax, Atlántica y Mediterránea. Durante la fase de alimentación endógena el empleo de alta temperatura incrementa preferiblemente la hipertrofia, observándose una fuerte disminución de la tasa hiperplásica en la fase prelarvaria, con independencia de la temperatura. Con el inicio de la alimentación viva comienza una etapa de rápido c...

Pb solubility of the high-temperature superconducting phase Bi2Sr2Ca2Cu3O10+d

International Nuclear Information System (INIS)

Kaesche, S.; Majewski, P.; Aldinger, F.

1994-01-01

For the nominal composition of Bi 2.27x Pb x Sr 2 Ca 2 Cu 3 O 10+d the lead content was varied from x=0.05 to 0.45. The compositions were examined between 830 degrees C and 890 degrees C which is supposed to be the temperature range over which the so-called 2223 phase (Bi 2 Sr 2 Ca 2 Cu 3 O 10+d ) is stable. Only compositions between x=0.18 to 0.36 could be synthesized in a single phase state. For x>0.36 a lead containing phase with a stoichiometry of Pb 4 (Sr,Ca) 5 CuO d is formed, for x 2 Sr 2 CaCu 2 O 8+d and cuprates are the equilibrium phases. The temperature range for the 2223 phase was found to be 830 degrees C to 890 degrees C but the 2223 phase has extremely varying cation ratios over this temperature range. Former single phase 2223 samples turn to multi phase samples when annealed at slightly higher or lower temperatures. A decrease in the Pb solubility with increasing temperature was found for the 2223 phase

Distribution of local critical current along sample length and its relation to overall current in a long Bi2223/Ag superconducting composite tape

International Nuclear Information System (INIS)

Ochiai, S; Doko, D; Okuda, H; Oh, S S; Ha, D W

2006-01-01

The distribution of the local critical current and the n-value along the sample length and its relation to the overall critical current were studied experimentally and analytically for the bent multifilamentary Bi2223/Ag/Ag-Mg alloy superconducting composite tape. Then, based on the results, it was attempted to simulate on a computer the dependence of the critical current on the sample length. The main results are summarized as follows. The experimentally observed relation of the distributed local critical current and n-value to the overall critical current was described comprehensively with a simple voltage summation model, in which the sample was regarded as a one-dimensional series circuit. The sample length dependence of the critical current was reproduced on the computer by a Monte Carlo simulation incorporating the voltage summation model and the regression analysis results for the local critical current distribution and the relation of the n-value to the critical current

Materiales compuestos C/SiC para aplicaciones estructurales de alta temperatura. Parte II: Sistemas de protección contra la oxidación

Directory of Open Access Journals (Sweden)

Aparicio, M.

2001-02-01

Full Text Available The fact which currently excludes the use of C/SiC composites in high temperature structural applications is the high oxidation rate of carbon fibres at temperatures higher than 450ºC. In this second part of the paper, a review of the different oxidation protection systems, including inhibitors, surface modification of composites, coatings and previous infiltration of the substrates, has been carried out. The addition of inhibitors reduces the oxidation rate, but only up to 850ºC, while the surface modification of composites leads to thin coatings with poor thermal shock resistance. On the other hand, the external layers are the most usual method employed because allows combining different compositions and thicknesses. The multilayer coatings are especially interesting in applications with wide temperature range and thermal shocks requirements. The infiltration of substrate porosity improves slightly the oxidation resistance of C/SiC composites reducing the oxygen accessibility to carbon fibres. However, the infiltration complements very well the oxidation protection performance of a coating system at low temperature, since these normally present open cracks due to mismatch between coating and substrate thermal expansion coefficients.

La utilización de los materiales compuestos C/SiC en aplicaciones estructurales a alta temperatura está limitada por la elevada velocidad de oxidación de la fibra de carbono a temperaturas superiores de 450ºC. En esta segunda parte del trabajo se realiza una revisión de las posibilidades de protección contra la oxidación de estos materiales, incluyendo inhibidores, modificación superficial del material compuesto, recubrimientos e infiltración previa del sustrato. La eficacia de los inhibidores de la reacción de oxidación esta restringida a temperaturas de hasta 850ºC, mientras que la modificación superficial del material compuesto da lugar a capas delgadas y poco resistentes a los ciclos t

Mecanismos de fractura a alta temperatura en aceros eléctricos no-orientados

Directory of Open Access Journals (Sweden)

García-Sánchez, E. O.

2007-08-01

Full Text Available In this research work the effect of deformation temperature on the hot ductility of non-oriented electrical steels (0.6 % Si-0.3 Al % was studied using high temperature tensile tests. The specimens were machined from two thin slabs (50 mm thickness produced by CSP process (Compact Strip Process, one of them using 100 % sponge iron and the other using 67 % scrap and 33 % sponge iron. The tensile tests were carried out at constant strain rate (5×1010^–4 s^–1, and a temperature range from 850 to 1,200 °C. The results showed that the ductility decreased with the increment in the temperature until approximately 1,000 °C. At higher temperatures, a ductility recovery was observed only in the steel fabricated without scrap. Scanning Electron Microscopy on fracture surfaces showed that the loss of ductility is associated with intergranular cracking promoted by the austenitic transformation and AlN grain boundaries precipitation.

Se investigó el efecto de la temperatura de deformación sobre la ductilidad de aceros eléctricos de grano no-orientado (0,6 % Si-0,3 % Al mediante ensayos de tracción uniaxial. Las probetas se obtuvieron de planchones delgados (50 mm de espesor tipo CSP (Continuous Strip Processing fabricados a partir de 100 % hierro esponja y una mezcla de 67 % chatarra y 33 % de hierro esponja. El rango de temperatura de estudio fue de 850 a 1.200 °C y los ensayos se llevaron a cabo a una velocidad de deformación constante de 5×10^–4 s^–1. Los resultados experimentales demostraron que la ductilidad (% RA disminuye con el aumento en la temperatura hasta un mínimo a ~1.000 °C. A temperaturas mayores, la ductilidad del acero fabricado a partir de 100 % hierro esponja se recupera. Este efecto no fue observado en el acero fabricado a partir de chatarra. La caracterización de las superficies de fractura mediante microscopía electrónica de barrido demostró que la pérdida de

A 13 kA current lead, measuring 1.5 m in length. The lower part consists of a high-temperature superconductor (Bi-2223), operating at between 50 K and 4.5 K, while the heat-exchanger upper part allows the current to be brought from room temperature to 50 K.

CERN Multimedia

2004-01-01

A 13 kA current lead, measuring 1.5 m in length. The lower part consists of a high-temperature superconductor (Bi-2223), operating at between 50 K and 4.5 K, while the heat-exchanger upper part allows the current to be brought from room temperature to 50 K.

Quench characteristics of Ag/AuBi2223 HTS-stainless steel stack used for the hybrid current leads of the large hadron collider

CERN Document Server

Al-Mosawi, M K; Beduz, C; Yang, Y; Ballarino, A

2008-01-01

The quench characteristics of Ag/Au sheathed Bi2223 tapes have been investigated in an adiabatic condition and in a configuration similar to that used in hybrid high temperature superconducting current leads, namely the 13000A leads used for the Large Hadron Collider at CERN. A specialised rig was designed and constructed to provide a carefully controlled environment. The samples were prepared from HTS tape soldered onto a stainless steel substrate with a number of temperature sensors at various positions along the length of tape. One end of the lead (cold end) was maintained at 6K using G-M cryo-cooler whereas the temperature of the other end (warm end) can be varied and maintained at temperatures up to 100K. The thermal runaway currents (quench currents) at various warm end temperatures (in the range of 40-100K) were determined. The temperature evolutions at various locations along the tape were recorded at different top end temperatures and currents. The effect of the stainless steel mechanical reinforceme...

Corrosion of high temperature resisting alloys exposed to heavy fuel ash; Corrosion de aleaciones resistentes a altas temperaturas expuestas a ceniza de combustoleo pesado

Energy Technology Data Exchange (ETDEWEB)

Wong Moreno, Adriana del Carmen

1998-03-01

content of vanadium and very low content of sulfur at temperatures near the point of fusion of he vanadium compounds that constitute them. The development of the processes of metallic deterioration that are included in the proposed model was documented through this investigation, for an alloy range, from low alloy steels to nickel based super alloys, as well as for a series of ash deposits whose composition covers a part of the spectra of combinations of sodium/sulfate vanadates that little has been explored. Among the more relevant aspects that were documented and included in the proposed global mechanism, stand out the following ones: The global mechanism of corrosion by ashes of heavy fuel oil based on 3 primary processes of alloy degradation is described: metallic dissolution, accelerated oxidation and sulfidazation. The influence that the temperature and the composition of the ash on the predominance of one or another degradation mechanism has. It is also analyzed how the transformation of the underlying zone to the metal/deposit interphase by diffusion processes and precipitation accelerates the kinetics of degradation of the alloy, particularly, it has been considered the change in the concentrations of Cr, Al and Si, and the sulfide precipitation. Finally, the results obtained contribute in addition with practical information on the alloy performance, which allows to establish an order of merit among the evaluated alloys as far as its resistance to the corrosion, and on the roll of the main alloyings in its behavior of corrosion by fuel oil ash deposits. [Espanol] El objetivo de la investigacion realizada fue estudiar el proceso de degradacion por corrosion a alta temperatura de aleaciones expuestas a cenizas de combustoleo pesado a traves de una evaluacion experimental comparativa de su desempeno que permitio establecer los mecanismos involucrados en el fenomeno. La experimentacion llevada a cabo involucro la determinacion de la resistencia a la corrosion de 14

Efecto de la temperatura sobre el crecimiento de plantas de papa (Solanum tuberosum L., variedades atlantic y 1625 frito lay, crecidas in vitro

Directory of Open Access Journals (Sweden)

Rafael Orozco

2016-03-01

Full Text Available En esta investigación, se estudio el efecto que causa sobre el crecimiento vegetativo de dos variedades de papa (1625 Frito Lay y Atlantic, el aumento de la temperatura en condiciones in vitro, para lo cual se usaron dos valores de temperatura (30/26 °C y 27/25 °C dia/noche. El medio de cultivo utilizado fue el MS (1962 de laboratorios Gibco, el cual se usó a razón de 17 g/L y se suplementó con vitaminas y aminoácidos del mismo medio. En ambas variedades la alta temperatura (30/26 °C causó una disminución en el diámetro del tallo y en el número de nudos por planta, así como un incremento en la longitud internodal y en la altura de la planta. Por otro lado, la alta temperatura disminuyó significativamente (P < 0,05 la longitud de la raíz en la variedad Frito Lay mientras que la variedad Atlantic mostró un incremento no significativo.

Magnetic properties and superconducting-fluctuation diamagnetism above Tc in Bi2-xPbxSr2CaCu2O8+δ (x=0.0, 0.1, 0.2, 0.3, 0.5) and

International Nuclear Information System (INIS)

Lee, W.C.; Cho, J.H.; Johnston, D.C.

1991-01-01

The magnetic susceptibilities χ(T) of the title compounds above and below T c are reported. For the Bi 2-x Pb x Sr 2 CaCu 2 O 8+δ (Bi 2:2:1:2) system, optimization of the phase purity and superconducting properties is found between x=0.2 and 0.3. The χ(T) data for these Bi 2:2:1:2 and for the two Bi 2:2:2:3 samples increase monotonically with temperature from T c up to at least 400 K, exhibiting strong negative curvature below ∼200 K. From theoretical fits to the data in the two-dimensional regime above T c using the static Lawrence-Doniach model as modified by Klemm, we conclude that the negative curvature in χ(T) for each sample arises from superconducting-fluctuation diamagnetism (SFD). The data are thus consistent with a superconducting order parameter of s-wave symmetry. From the fits to the data, the Ginzburg-Landau coherence lengths in the CuO 2 planes were obtained and found to be ξ ab (0)=20.4(2) A for Bi 2:2:1:2 and 11.8(4) A for Bi 2:2:2:3. The value for Bi 2:2:1:2 is comparable to those calculated from upper critical magnetic-field data for this compound (23.5--27.1 A). Our ξ ab (0) values for Bi 2:2:1:2 and Bi 2:2:2:3 are also comparable with that (13.6 A) found from our previous similar analysis of the SFD in YBa 2 Cu 3 O 7 . The possible role of the bridging oxygens out of the CuO 2 plane in Bi 2:2:2:3 and the influence of the dynamics in the fits to the SFD in the Bi-based compounds remain to be addressed

Critical current of high Tc superconducting Bi223/Ag tapes

NARCIS (Netherlands)

Huang, Y.; ten Haken, Bernard; ten Kate, Herman H.J.

1998-01-01

The magnetic field dependence of the critical current of various high Tc superconducting Bi2223/Ag tapes indicates that the transport current is carried through two paths: one is through weakly-linked grain boundaries (Josephson junctions); another is through well-connected grains. The critical

Preparation and characterization of Ag-added Bi1⋅84Pb0 ...

Indian Academy of Sciences (India)

Unknown

microscopy (SEM), electrical transport and a.c. susceptibility techniques. The tube ... high current conductor is high Jc. However, non-textured, porous structure with ... contact resistance studies on Ag added (0–25 wt%) Bi-. 2223 bulk tubes ...

Metal temperature monitoring in corrosive gases at high temperature and high thermal flows; Monitoreo de temperaturas de metal en gases corrosivos a alta temperatura y altos flujos termicos

Energy Technology Data Exchange (ETDEWEB)

Huerta Espino, Mario; Martinez Flores, Marco Antonio; Martinez Villafane, Alberto; Porcayo Calderon, Jesus; Gomez Guzman, Roberto; Reyes Cervantes, Fernando [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1991-12-31

The direct measurement of metal temperatures during operation in superheater, reheater, and water wall tubes in zones exposed to high thermal flows is of great interest for the operation and analysis of the correct functioning of a steam generator. The operation temperature measurement of these zones differs very much of the monitored temperature in headers in the dead chamber, since the temperature measured in this zone is the steam temperature that does not reflect the one detected in the gas zone. For this reason, the thermocouples implant in gas zones will detect the real metal temperature and the incidence that some operation variables might have on it (Martinez et al., (1990). [Espanol] La medicion directa de temperaturas de metal durante operacion en tubos de sobrecalentador, recalentador y pared de agua en zonas expuestas a altos flujos termicos es de gran interes para la operacion y analisis del buen funcionamiento de un generador de vapor. La medicion de la temperatura de operacion de estas zonas, difiere mucho de la temperatura monitoreada en cabezales en zona de camara muerta, ya que la temperatura registrada en esta zona es la de vapor que no es un reflejo de la detectada en zona de gases. Por esta razon, la implantacion de termopares en zona de gases detectara la temperatura de metal real y la incidencia que algunas variables de operacion tengan sobre esta (Martinez et al., 1990).

Metal temperature monitoring in corrosive gases at high temperature and high thermal flows; Monitoreo de temperaturas de metal en gases corrosivos a alta temperatura y altos flujos termicos

Energy Technology Data Exchange (ETDEWEB)

Huerta Espino, Mario; Martinez Flores, Marco Antonio; Martinez Villafane, Alberto; Porcayo Calderon, Jesus; Gomez Guzman, Roberto; Reyes Cervantes, Fernando [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

1990-12-31

The direct measurement of metal temperatures during operation in superheater, reheater, and water wall tubes in zones exposed to high thermal flows is of great interest for the operation and analysis of the correct functioning of a steam generator. The operation temperature measurement of these zones differs very much of the monitored temperature in headers in the dead chamber, since the temperature measured in this zone is the steam temperature that does not reflect the one detected in the gas zone. For this reason, the thermocouples implant in gas zones will detect the real metal temperature and the incidence that some operation variables might have on it (Martinez et al., (1990). [Espanol] La medicion directa de temperaturas de metal durante operacion en tubos de sobrecalentador, recalentador y pared de agua en zonas expuestas a altos flujos termicos es de gran interes para la operacion y analisis del buen funcionamiento de un generador de vapor. La medicion de la temperatura de operacion de estas zonas, difiere mucho de la temperatura monitoreada en cabezales en zona de camara muerta, ya que la temperatura registrada en esta zona es la de vapor que no es un reflejo de la detectada en zona de gases. Por esta razon, la implantacion de termopares en zona de gases detectara la temperatura de metal real y la incidencia que algunas variables de operacion tengan sobre esta (Martinez et al., 1990).

The spatial distribution of temperature and oxygen deficiency in spark-plasma sintered superconducting Bi-based materials

International Nuclear Information System (INIS)

Govea-Alcaide, E.; Pérez-Fernández, J.E.; Machado, I.F.; Jardim, R.F.

2014-01-01

Pre-reacted powders of (Bi–Pb) 2 Sr 2 Ca 2 Cu 3 O 10+δ (Bi-2223) were consolidated by using the spark plasma sintering (SPS) technique under vacuum and at different consolidate temperatures T D . X-ray diffraction patterns revealed that the dominant phase in all SPS samples is the Bi-2223 phase, but traces of the Bi 2 Sr 2 CaCu 2 O 10+x (Bi-2212) phase were identified. We have found that the transport properties of SPS samples depend on their oxygen content because the SPS process is performed under vacuum. Simulations by using the finite element method (FEM) were performed for determining the actual temperature in which powders are consolidated. From these results we have inferred that SPS samples are oxygen deficient and such a deficiency is more marked near the grain boundaries, suggesting the occurrence of grains with core–shell morphology. We also argued that the width of the shell depends on the consolidation temperature, a feature corroborated by the FEM simulations

Method of producing superconducting fibers of bismuth strontium calcium copper oxide (Bi(2212) and Bi(2223))

Science.gov (United States)

Schwartzkopf, Louis A.

1991-10-01

Fibers of Bi(2212) have been produce by pendant drop melt extraction. This technique involves the end of a rod of Bi(2212) melted with a hydrogen-oxygen torch, followed by lowering onto the edge of a spinning wheel. The fibers are up to 15 cm in length with the usual lateral dimensions, ranging from 20 um to 30 um. The fibers require a heat treatment to make them superconducting.

Influence of conditions of preparation on quality of superconductors Bi(Pb)SrCaCuO with boron

International Nuclear Information System (INIS)

Sykorova, D.; Smrckova, O.; Ptrydes, D.; Vasek, P.

1999-01-01

The aim of this work was to verify influence of B 2 O 3 on formation of the phase Bi-2223 of samples with nominal composition Bi 1.8 (Pb 0.26 )Sr 2 Ca 2 Cu 3 O 8+x . Conditions of preparation of superconductors as well as their properties are described

Studies on Bi-Sr-Ca-Cu-O glasses and superconducting glass ceramics

International Nuclear Information System (INIS)

Singh, R.; Zacharias, E.

1991-01-01

Bi-Sr-Ca-Cu-O glasses and glass ceramics of various compositions were synthesised. The glass transition temperature varies from 396 to 422degC depending on the glass composition. The bulk glass ceramics of 4334, 4336, 2223 and 4246 compositions show superconductivity when the corresponding glass samples were heat-treated in air at 820degC for 3, 9, 12 and 24 h respectively. X-ray diffraction studies show that the superconducting phase present in all these compositions is Bi 2 Sr 2 Ca 1 Cu 2 O x . The 4334 glass ceramic is almost a single-phase material with a preferred orientation such that the c axis is normal to the sample surface. The 2223 glass ceramic has a higher T c (onset) than the other three compositions indicating the presence of high T c phase (110 K) also. ESR studies on the glass samples indicate the existence of Cu 2+ . The effect of heat treatment on ESR shows that the intensity of resonance decreases with increase in heat-treatment duration. This effect is more pronounced for the 4334 and 2223 compositions. The advantages of synthesizing superconducting materials by glass route are discussed in view of practical applications. (author). 9 refs., 6 figs

Atomic displacements effects on the electronic properties of Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}

Energy Technology Data Exchange (ETDEWEB)

Camargo M, J. A. [Fundacion Universitaria Internacional del Tropico Americano, Grupo de Investigacion en Ciencias Basicas, Aplicacion e Innovacion, Carrera 19 No. 39-40, Yopal, Yopal (Colombia); Espitia, D.; Baquero, R., E-mail: jcamargo@unitropico.edu.co [Instituto Politecnico Nacional, Centro de Investigacion y de Estudios Avanzados, Departamento de Fisica, Av. IPN 2508, 07360 Mexico D. F. (Mexico)

2015-07-01

The displacements effects of the oxygen atom associated to the Sr-plane (O3) in the electronic properties of Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Bi-2223), have been investigated using density functional theory. We determined intervals of the O3 atomic positions for which the band structure calculations show that the Bi-O bands, around the high symmetry point M in the irreducible Brillouin zone, emerge towards higher energies avoiding its contribution at Fermi level, as experimentally has been reported. This procedure does not introduce foreign doping elements into the calculation. Our calculations present a good agreement with the angle-resolved photoemission spectroscopy and nuclear magnetic resonance (NMR) experiments. The two options found differ in character (metallic or nonmetallic) of the Bi-O plane. The are not any experiments, to the best of our knowledge, which determine this character for Bi-2223. (Author)

Aspectos experimentales de la determinacion de curvas esfuerzo-deformacion a alta temperatura y en atmosfera controlada: Refractarios Al2O3-MgO-C

Directory of Open Access Journals (Sweden)

Cavalieri, A. L.

2011-06-01

Full Text Available A methodology for the mechanical evaluation of refractory materials at high temperatures and controlled atmosphere, designed and implemented in the Structural Materials Laboratory of Ceramics Division of INTEMA, is described. The methodology includes the measurement of the specimen deformation by contact extensometry in compression tests to obtain stress-strain curves and the use of a gaseous flow as a system to control atmosphere. The determination of stress-strain curves of Al2O3-MgO-C commercial refractories used in steelmaking ladles at room temperature and 1260°C in different atmospheres is presented as an example of application of this methodology.Se presenta una metodología diseñada e implementada en el Laboratorio de Materiales Estructurales de la División Cerámicos del INTEMA para la evaluación del comportamiento mecánico de materiales refractarios a altas temperaturas y en atmósfera controlada. La metodología comprende la determinación de la deformación por extensometría de contacto en ensayos en compresión con el fin de obtener curvas esfuerzo-deformación y el uso de un sistema de control de atmósfera por desplazamiento a través del pasaje de una corriente gaseosa. La determinación de curvas esfuerzo-deformación de ladrillos refractarios comerciales Al2O3-MgO-C utilizados en cucharas de acería a temperatura ambiente y a 1260 °C en diferentes atmósferas se presenta como ejemplo de aplicación de esta metodología.

Comparison between tympanic and anal temperature with a clinical infrared ray thermometer in dogs Comparação entre a temperatura timpânica e a temperatura anal usando um termômetro clínico de raio infravermelho em cães

Directory of Open Access Journals (Sweden)

G.G.S. Wiedemann

2006-08-01

Full Text Available A clinical thermometer of infrared rays was used twice to record consecutively the temperature of the tympanic membrane in each ear and in the anus of 53 dogs. Temperatures did not differ significantly between organs, and were strongly correlated. The anal temperature measurement with an infrared thermometer in dogs is feasible and trustworthy, as well as the thermal checking of tympanic temperature.Utilizou-se um termômetro clínico de emissão de raios infravermelhos para medir, duas vezes consecutivas, a temperatura da membrana timpânica de cada ouvido e duas vezes a temperatura no ânus de 53 cães. Não houve diferença entre as temperaturas quanto ao órgão estudado e a correlação entre as temperaturas foi alta. Em cães, a medida da temperatura anal com o termômetro clínico de emissão de raios infravermelhos é rápida e confiável tanto quanto a da temperatura timpânica.

Diseño, Implementación y Verificación de un Sensor de Temperatura CMOS de Bajo Coste y Alta Funcionalidad

OpenAIRE

Artés García, Antonio

2007-01-01

En este proyecto, se presenta un sensor de temperatura integrado CMOS basado en la medida de una variable secundaria, cuyo valor es dependiente de la temperatura, como es el tiempo de subida que presenta una señal eléctrica en sus flancos de subida. Con el objetivo de reducir coste y potencia consumida, el sensor integrado de temperatura propuesto genera un pulso con un ancho proporcional a la temperatura medida. Este sensor para realizar la medida elimina la necesidad de tener una señal que ...

20 CFR 222.3 - Other regulations related to this part.

Science.gov (United States)

2010-04-01

... 20 Employees' Benefits 1 2010-04-01 2010-04-01 false Other regulations related to this part. 222.3 Section 222.3 Employees' Benefits RAILROAD RETIREMENT BOARD REGULATIONS UNDER THE RAILROAD RETIREMENT ACT FAMILY RELATIONSHIPS General § 222.3 Other regulations related to this part. This part is related to a...

Effect of lead addition on the formation of superconducting phases in Bi-Sr-Ca-Cu-O ceramics

International Nuclear Information System (INIS)

Martinelli, A.E.

1991-01-01

Superconducting ceramics with starting composition Bi 2 - x Pb x Sr 2 Ca 2 Cu 3 O y (0,0 ≤ X ≤ 0,6) were prepared in order to investigate the effects of partial substitution of Pb for Bi and sintering time and atmosphere in the formation of superconducting phases. For all samples X-ray diffraction analyses were performed to estimate the amount of superconducting phases; superconductivity was analysed by dc electrical resistance and ac magnetic susceptibility measurements. The main results show that: a) the longer the sintering time (up to 168 h), the larger the volume fraction of superconducting phases with critical temperature (T c ) greater than the temperature of nitrogen liquefaction; b) by partially substituting Pb for Bi it is possible to restrain the formation of 2212 phase (T c = 80 K) and to enhance the amount of 2223 phase (T c = 105 K); C) a heat treatment under oxygen atmosphere before sintering enhances the formation of 2223 phase. (author)

DIALIGN: multiple DNA and protein sequence alignment at BiBiServ.

OpenAIRE

Morgenstern, Burkhard

2004-01-01

DIALIGN is a widely used software tool for multiple DNA and protein sequence alignment. The program combines local and global alignment features and can therefore be applied to sequence data that cannot be correctly aligned by more traditional approaches. DIALIGN is available online through Bielefeld Bioinformatics Server (BiBiServ). The downloadable version of the program offers several new program features. To compare the output of different alignment programs, we developed the program AltA...

Experiment of enhancing critical current and reducing ac loss in pancake coil comprised of Ni-coated Bi-2223/Ag tape

International Nuclear Information System (INIS)

Alamgir, A.K.M.; Gu, C.; Han, Z.

2006-01-01

An approach of realizing high performance HTS coil comprised of ferromagnetic material-coated BSCCO tape is proposed. The concept of influencing critical current and ac loss is based on the magnetic shielding effect resulting in redirection of self-field flux-lines. In the previous article, ac performance of Ni-coated tape was demonstrated where the Ni-coating was introduced at the edge-regime of the finished tape in order to redirect the perpendicular component of self-field lines. In order to investigate the shielding effect on ac performance in HTS coil, a two-turn pancake coil comprised of Ni-coated Bi-2223/Ag tape is demonstrated in the present article. About 6.4% of critical current was enhanced and 30% of transport current ac loss was reduced by means of 40 μm thick and 0.3 mm long (from the edge toward center of the tape) Ni-coating. This result suggests that additional ferromagnetic loss could be compensated well by the shielding effect of the partial Ni-coating. The degree of enhancement in critical current as well as ferromagnetic impact on ac losses depend on the volume and geometry of ferromagnetic coating introduced. Therefore, it is very important to control the parameter of ferromagnetic coating of the tape in order to balance the critical current and ac loss for optimum coil performance

Experiment of enhancing critical current and reducing ac loss in pancake coil comprised of Ni-coated Bi-2223/Ag tape

Energy Technology Data Exchange (ETDEWEB)

Alamgir, A.K.M. [Department of Physics, Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China)]. E-mail: alam643@hotmail.com; Gu, C. [Department of Physics, Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China); Han, Z. [Department of Physics, Applied Superconductivity Research Center, Tsinghua University, Beijing 100084 (China)

2006-07-01

An approach of realizing high performance HTS coil comprised of ferromagnetic material-coated BSCCO tape is proposed. The concept of influencing critical current and ac loss is based on the magnetic shielding effect resulting in redirection of self-field flux-lines. In the previous article, ac performance of Ni-coated tape was demonstrated where the Ni-coating was introduced at the edge-regime of the finished tape in order to redirect the perpendicular component of self-field lines. In order to investigate the shielding effect on ac performance in HTS coil, a two-turn pancake coil comprised of Ni-coated Bi-2223/Ag tape is demonstrated in the present article. About 6.4% of critical current was enhanced and 30% of transport current ac loss was reduced by means of 40 {mu}m thick and 0.3 mm long (from the edge toward center of the tape) Ni-coating. This result suggests that additional ferromagnetic loss could be compensated well by the shielding effect of the partial Ni-coating. The degree of enhancement in critical current as well as ferromagnetic impact on ac losses depend on the volume and geometry of ferromagnetic coating introduced. Therefore, it is very important to control the parameter of ferromagnetic coating of the tape in order to balance the critical current and ac loss for optimum coil performance.

Estudo de espalhamento Raman em cristais de L-leucina submetidos a altas temperaturas e a altas pressÃes

OpenAIRE

Pedro de Freitas FaÃanha Filho

2007-01-01

Neste trabalho foram realizadas medidas de espalhamento Raman polarizado à temperatura ambiente e medidas de absorÃÃo no infravermelho em cristais do aminoÃcido L-leucina com o objetivo de se determinar os modos normais de vibraÃÃo do material. Para isto, utilizou-se auxiliarmente a classificaÃÃo dos modos normais de vibraÃÃo disponÃveis para outros trÃs aminoÃcidos protÃicos alifÃticos, a L-alanina, a L-Âvalina e a L-isoleucina. Na segunda parte do trabalho estudou-se o comportamento dos mod...

Transport current ac losses and current-voltage curves of multifilamentary Bi-2223/Ag tape with artificial defects

International Nuclear Information System (INIS)

Polak, M.; Jansak, L.

2000-01-01

We experimentally studied the effects of a single artificial defect and a linear array of artificial defects on I-V curves, critical currents and transport current ac losses of 55 filament untwisted Bi-2223/Ag tapes. The artificial defect was a small hole drilled into the tape. The reduction in the critical current measured on a 1 cm long section due to one hole of diameter 0.9 mm was 33% and that due to a linear array of seven similar holes was 62%. The slopes of the I-V curves, n, measured in this section were 33, 16 and 5.8 in the original sample, in the sample with one defect and the sample with seven defects, respectively. Both I c and the slope reduction were smaller if the distance between the potential taps was increased. The transport current ac losses at 50 Hz and I rms = 10 A in the sample with one defect measured in a 1 cm long section were practically the same as those in the original sample (4.1x10 -4 W m -1 ), but they increased by 83% in the sample with a linear array of seven defects. The measured increase in losses per unit length was the smaller, the larger the distance between the potential taps. A comparison between the measured and calculated losses revealed that a formal application of the Norris equations for loss calculations in samples with local defects leads to an overestimation of the ac losses. A procedure for the calculation of transport current losses in samples with local defects based on the Norris model is proposed and verified. (author)

Investigación en materiales sometidos a altas presiones

Directory of Open Access Journals (Sweden)

Juan Carlos Fallas

2010-10-01

Full Text Available El estudio de materiales sometidos a altas presiones es un tema de profundo interés en el campo científico e ingenieril actual. Diferentes análisis experimentales permiten descubrir los efectos que esta condición genera en la estructura molecular de un determinado compuesto.La implementación de la celda de diamante para altas presiones ha revolucionado este tema en las últimas décadas, al ser una herramienta vital en el desarrollo de estas pruebas. Presiones superiores, inclusive a los 20 Gpa, pueden ser generadas con este artefacto.Adicionalmente, la posibilidad de caracterizar muestras bajo estos parámetros y la inclusión de otras variables, como altas temperaturas, ofrecen un ambiente propicio para la evaluación de materiales bajo condiciones extremas.Este artículo explica los fundamentos básicos de la ciencia de materiales a altas presiones. Aspectos relevantes acerca de la celda de diamante y de la ejecución de experimentos son tratados en diferentes apartados. Se quiere compartir los alcances que esta disciplina posee, así como diferentes resultados que se han logrado en varias aplicaciones.Investigaciones en materiales para el almacenamiento de hidrógeno y energía, así como la simulación de condiciones presentes a muy altas profundidades en la Tierra, son casos que se tomaron en cuenta para ejemplificar áreas donde existen aplicaciones sustanciales.

75 FR 23263 - Alta Wind I, LLC; Alta Wind II, LLC; Alta Wind III, LLC; Alta Wind IV, LLC; Alta Wind V, LLC...

Science.gov (United States)

2010-05-03

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL10-62-000] Alta Wind I, LLC; Alta Wind II, LLC; Alta Wind III, LLC; Alta Wind IV, LLC; Alta Wind V, LLC; Alta Wind VI, LLC; Alta Wind VII, LLC; Alta Wind VIII, LLC; Alta Windpower Development, LLC; TGP Development Company, LLC...

77 FR 29633 - Alta Wind VII, LLC, Alta Wind IX, LLC, Alta Wind X, LLC, Alta Wind XI, LLC, Alta Wind XII, LLC...

Science.gov (United States)

2012-05-18

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. EL12-68-000] Alta Wind VII, LLC, Alta Wind IX, LLC, Alta Wind X, LLC, Alta Wind XI, LLC, Alta Wind XII, LLC, Alta Wind XIII, LLC, Alta Wind XIV, LLC, Alta Wind XV, LLC, Alta Windpower Development, LLC, TGP Development Company, LLC...

36 CFR 222.3 - Issuance of grazing and livestock use permits.

Science.gov (United States)

2010-07-01

... livestock use permits. 222.3 Section 222.3 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE RANGE MANAGEMENT Grazing and Livestock Use on the National Forest System § 222.3 Issuance of grazing and livestock use permits. (a) Unless otherwise specified by the Chief, Forest Service, all...

Correlación entre la microestructura y el comportamiento plástico a alta temperatura de compuestos TZP-Ni (40% vol.

Directory of Open Access Journals (Sweden)

Morales-Rodríguez, A.

2005-10-01

Full Text Available Microstructure and high-temperature mechanical behaviour of TZP-Ni composites with 40 vol.% of nickel above the percolation threshold (placed in 34 vol.% in these wet‑processed ceramic-metal composites has been studied. The microstructure has been characterized using scanning electron microscopy. The composite plasticity has been studied by means of uniaxial compressive creep tests under constant load in argon atmosphere carried out in the temperature range between 900 and 1250 ºC and stresses between 9 and 144 MPa. TZP skeleton has been deformed in similar conditions to study nickel effect in global cermet behavior. The metallic phase has been removed from the cermets using chemical etching with HNO3. The plastic behavior of these materials is controlled by the ceramic matrix. The deformation rates are higher than monolithic TZP ones. This fact has been explained taking into account the metallic phase distribution into the matrix in these composites. Metal percolation provides materials with high ductility allowing the cermets to deform at temperatures as low as 900 ºC.

Se ha estudiado la microestructura y el comportamiento mecánico a alta temperatura de compuestos de circona tetragonal (3Y-TZP con un 40% en volumen de níquel (referidos en adelante como TZP-Ni. El contenido en níquel está por encima del punto de percolación, que en estos compuestos cerámico-metal procesados en vía húmeda se sitúa en el 34% vol. de contenido metálico. La caracterización microestructural se ha realizado mediante observaciones de microscopía electrónica de barrido. La plasticidad de los compuestos se ha estudiado mediante ensayos de fluencia en compresión uniaxial a carga constante en atmósfera de argón realizados en el rango de temperaturas entre 900 y 1250 ºC y tensiones entre 9 y 144 MPa. Para estudiar el efecto del níquel en el comportamiento del cermet se ensayaron en condiciones similares esqueletos de TZP, obtenidos mediante la

Superconducting properties of Bi-based ceramics with column 3A elements

Czech Academy of Sciences Publication Activity Database

Smrčková, O.; Sýkorová, D.; Rubešová, K.; Vašek, Petr

2002-01-01

Roč. 321, - (2002), s. 292-294 ISSN 0921-4526 R&D Projects: GA ČR GA106/99/1441; GA ČR GA104/99/1440 Institutional research plan: CEZ:AV0Z1010914 Keywords : Bi2223 * substitution B, Al, Ca, In * critical phenomena Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.609, year: 2002

Microscopic fracture of filaments and its relation to the critical current under bending deformation in (Bi,Pb)2Sr2Ca2Cu3O10 composite superconducting tapes

International Nuclear Information System (INIS)

Hojo, Masaki; Nakamura, Mitsuhiro; Matsuoka, Tomoe; Tanaka, Mototsugu; Ochiai, Shojiro; Sugano, Michinaka; Osamura, Kozo

2003-01-01

The strain dependence of the critical current, I c , of (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O 10 (Bi2223)/Ag/Ag-Mg composite superconducting tapes has been studied both experimentally and analytically under bending deformation. Tests have been carried out for one type of tape used in the VAMAS bending round-robin programme. The complex stress-strain behaviour of each component was first analysed in tension. This was done by comparing the stress-strain curves of composite tapes with those of Ag and Ag-Mg alloy tapes. Here, the plastic deformation (work hardening) of Ag and Ag-Mg alloy, and the thermal residual strain due to the manufacturing process were taken into account. The fracture strain of Bi2223 filaments was inversely determined as 0.08% to meet the global tensile stress-strain curve of the composite tape. The calculated stress-strain curves finally agreed well with the experimental results when the as-supplied bending strain was taken into account. Then, the analysis was modified to fit the bending deformation. Here, the movement of the neutral axis due to the non-symmetric and elastic-plastic stress-strain curves of the components and their Bauschinger effect were taken into account. The relative decrease of I c with the increase in the Bi2223 tape curvature was calculated from the volume fraction of the broken filaments. The calculated I c agreed well with the experimental results when the movement of the neutral axis and the Bauschinger effect were taken into account. Microscopic observation of the spatial distribution of the filament fracture indicated that the damage occurred at the outermost layer on the tensile side when the curvature was small, and then the damage front shifted to the inside layers. The observed fracture behaviour of the Bi2223 filament agreed well with the estimated location based on the above analysis

Informe de personal de apoyo: Alvarez Martini, Carlos Alberto (2014-2015) 

OpenAIRE

Alvarez Martini, Carlos Alberto

2016-01-01

Proyectos de investigación en los cuales colabora: 1) Proyecto 11 G 133 UNLP- Metrología bi y tridimensional en el diseño,desarrollo y aplicación de concentradores ópticos solares para altas temperaturas. 1/1/2014 al 31/12/2017. Director Lic. Luis Martorelli

Sem-EDAX'S Application For Characterization Of Superconductor Material Of (Bi,Pb)-Sr-Ca-Cu-O

International Nuclear Information System (INIS)

Handayani, Ari; Wuryanto; Prambudi, Bambang

1996-01-01

The microstructure and composition analysis of superconductor material of (Bi,Pb)-Sr-Ca-Cu-O which were synthesized by two different processes (CA and CD Process) by varying the sintering time, i.e. 20,60 and 100 hours were done by using SEM-EDAX method. The standard sample of superconductor material of Bi-Sr-Ca-Cu-O with 1112, 2212 and 2223 phase from Stream has been used for comparison, At 25 kV, the composition analysis showed that, at 20 and 60 hours of sintering, a mixture of phases existed while 100 hours of sintering resulted in a phase close to phase 2223. The result of microstructure observation showed significant differences. At synthesized CA process, 100 hours of sintering gives bigger and clearer platelet microstructure shape than that given by 20 and 60 hours of sintering. Also from the synthesized CD process, the 60 and 100 hours of sintering gives bigger and clearer platelet microstructure shape than that given by the 20 hours of sintering

temperatura

Directory of Open Access Journals (Sweden)

Alirio Yovany Benavides

2008-01-01

Full Text Available El biodiesel de aceite de palma (BAP posee excelentes propiedades como combustible para motores. Sin embargo, asociado con su composición química altamente saturada, este biocombustible presenta un deficiente desempeño a temperaturas cercanas a la temperatura ambiente de varias ciudades colombianas. A 16 ºC, el BAP empieza a formar pequeños cristales, los cuales, a medida que la temperatura sigue disminuyendo, aceleran su crecimiento y se aglomeran, de tal modo, que a una temperatura entre 12 y 9 ºC pueden llegar a impedir completamente el flujo del combustible. En este trabajo se evaluó la técnica del fraccionamiento del BAP mediante cristalización inducida por enfriamiento para mejorar sus propiedades de flujo a baja temperatura (PFBT. Las variables tenidas en cuenta para dicho proceso fueron la temperatura de enfriamiento o de winterization (Tw y el tiempo de estabilización (tp. De acuerdo con los punto de nube (PN y fluidez (PF del BAP, el rango de temperaturas de enfriamiento que se pudo ensayar fue muy limitado (12 ºC-16 ºC. El proceso permitió obtener una fracción líquida a la Tw con mejores PFBT que el BAP original. Para las condiciones extremas probadas (tp=24 horas y Tw=14 ºC se obtuvo una fracción líquida con un PN 6 ºC menor que el del BAP sin fraccionar. Dicho cambio en el PN correspondió a un aumento en el contenido de metilésteres insaturados de 4,7% y una reducción en el contenido de metilésteres del ácido palmítico de 5,29%. Los cambios inducidos en la composición química de las fracciones líquidas no alcanzaron a tener efectos significativos en sus propiedades básicas como combustibles.

Microestructura y comportamiento mecánico a altas temperaturas de cerámicas biomorficas de carburo de silicio

Directory of Open Access Journals (Sweden)

Martínez-Fernández, J.

2001-04-01

Full Text Available Environment conscious ceramics (ecoceramics are a new class of ceramic materials fabricated from natural wood (a renewable source. The affordable, net shape ceramics are fabricated by pyrolysis and molten silicon infiltration of wood preforms. The resulting materials have complex microstructure and multifunctional properties. The microstructure before and after high temperature plastic deformation was studied by scanning electron microscopy. These ceramics present regions of silicon and silicon carbide that follow the fibrous microstructure of the wood selected, resulting in a structure that resembles a continuos fiber composite. This structure results in very good mechanical properties as the evolutionary process has perfected it.

Las cerámicas respetuosas con el medio ambiente (ecocerámicas son una nueva clase de materiales cerámicos fabricados a partir de madera natural (un recurso renovable. Estas cerámicas se fabrican mediante la pirólisis de la preforma de madera e infiltración de silicio líquido en esta, proceso de bajo coste y con poco cambio de forma. El material resultante tiene una microestructura compleja y propiedades multifuncionales. La microestructura antes y después de la deformación plástica a alta temperatura se estudió mediante microscopía electrónica de barrido. Estas cerámicas presentan regiones de silicio y de carburo de silicio que mantienen la microestructura fibrosa de la madera seleccionada, similar a la de un material compuesto de fibra continua. Esta estructura ha resultado poseer unas muy buenas propiedades mecánicas a la compresión en caliente, en la dirección de las fibras, ya que el proceso evolutivo la ha perfeccionado.

Systematics in Bi-2201, -2212 and -2223 superconductors studied by positron annihilation radiation measurements

International Nuclear Information System (INIS)

Sanyal, D.; Banerjee, D.; De, Udayan

1998-01-01

Positron lifetimes in Bi 2 Sr 2 Ca (n-1) Cu n O (2n+4+δ) or Bi-22(n-1)n superconducting compounds for n=1, 2 and 3 have been determined from positron annihilation lifetime (PAL) spectroscopy of associated γ-radiations. Bulk lifetime is shown to increase systematically with increase of n, the number of CuO 2 -layers in the Bi-22(n-1)n compound. Positron annihilation probing of structural units of this perovskite-like crystal system has thus been demonstrated

Microestructura y piezoelectricidad de cerámicas de Bi3TiNbO9 obtenidas a partir de precursores activados mecanoquimicamente

Directory of Open Access Journals (Sweden)

Jiménez, B.

1999-12-01

Full Text Available Bi3TiNbO9 is one of the Aurivilius-type structure compounds, of general formula [Bi2O2][An-1BnO3n+1], made from pseudoperovskite (with n=2 layers alternating with Bi2O2 layers. It belongs to an ensemble of high transition temperature ferroelectrics that attracts nowadays a great deal of interest as piezoelectric materials for high temperature use (p.e. in non-destructive testing of materials by ultrasounds for siderurgy, nuclear plants or petrochemical industry. When prepared as thin films, they have interest as non-volatile computer memories (FERAM, due to their reduced fatigue, large polarization retention and low leakage currents. In solid state reaction and sintering, the lamellae-like growing habit, that resembles the layered crystalline structure, gives place to porous ceramics. Previous works used hot uniaxial pressing in order to obtain dense ceramics at low temperatures, avoiding changes in stoichiometry and exagerated grain growth. But, such ceramics have anisotropic properties. In order to overcome these problems, Bi3TiNbO9 ceramics were obtained by cold-pressing of amorphous powder and sintering. The amorphous precursor was obtained by mechanochemical activation of a stoichiometric oxides mixture. The quantitative microstructural, ferro and piezoelectric characterization of the ceramics reveals that these ceramics have lower porosity, higher hardness, are better polarizable and show higher piezoelectric response that those prepared from solid state reaction powder.El compuesto Bi3TiNbO9 presenta una estructura tipo Aurivillius, de fórmula general [Bi2O2][An-1BnO3n+1], constituida por capas de pseudo-perovskita (con n=2 intercaladas con capas de Bi2O2. Pertenece a una familia de ferroeléctricos de alta temperatura de transición, que son interesantes como materiales piezoeléctricos para usos a alta temperatura y, cuando se preparan en lámina delgada, en su aplicación en memorias ferroeléctricas no volátiles (FERAM. La

Superconducting Bi-Sr-Ca-Cu-O thin films from metallo-organic complexes

International Nuclear Information System (INIS)

Gruber, H.; Krautz, E.; Fritzer, H.P.; Popitsch, A.

1991-01-01

Thin films in the Bi-Sr-Ca-Cu-O system are produced by decomposition of organic precursor compounds containing different metallo-organic complexes. The superconducting phase identified is Bi 2 Sr 2 CaCu 2 O 8+x on (100)-MgO single crystal substrates, polycrystalline Au- and Ag-ribbons and Bi 2 Sr 2 Ca 2 Cu 3 O 10+x on Ag-ribbons. For the 2212-phase a zero resistance temperature of 79 K is found. The 2223-samples on Ag-ribbons show a broad transition at 110 K with a zero resistance at 85 K. SEM and EDX are used for the detection of the microstructure and composition of the prepared films. (orig.)

Systematics in Bi-2201, -2212 and -2223 superconductors studied by positron annihilation radiation measurements

Energy Technology Data Exchange (ETDEWEB)

Sanyal, D.; Banerjee, D. [Department of Physics, University of Calcutta, Calcutta (India); De, Udayan [Variable Energy Cyclotron Centre, 1/AF Bidhan Nagar, Calcutta (India)

1998-12-01

Positron lifetimes in Bi{sub 2}Sr{sub 2}Ca{sub (n-1)}Cu{sub n}O{sub (2n+4+{delta}}{sub )} or Bi-22(n-1)n superconducting compounds for n=1, 2 and 3 have been determined from positron annihilation lifetime (PAL) spectroscopy of associated {gamma}-radiations. Bulk lifetime is shown to increase systematically with increase of n, the number of CuO{sub 2}-layers in the Bi-22(n-1)n compound. Positron annihilation probing of structural units of this perovskite-like crystal system has thus been demonstrated.

Infarto do miocárdio e acidente vascular cerebral associados à alta temperatura e monóxido de carbono em área metropolitana do sudeste do Brasil Miocardic infarcts and cerebral-vascular accidents associated with high temperature and carbon monoxide in an metropolitan area of Southeastern Brazil

Directory of Open Access Journals (Sweden)

Davi Rumel

1993-02-01

Full Text Available Muito se tem publicado e discutido acerca de fatores de risco ligados a estilo de vida e a fatores hereditários em Acidente Vascular Cerebral (AVC e Infarto do Miocárdio (IM. Porém o estudo da influência de fatores ambientais como poluição por monóxido de carbono e temperatura na determinação nas ocorrências dessas patologias ainda é pouco discutido em nosso meio. Visando preencher esta lacuna, foi verificada a associação existente entre os valores de temperaturas máximas diárias e valores médio e máximo diários de monóxido de carbono e AVC e IM no Município de São Paulo, SP (Brasil. Foi coletada uma série histórica do número de casos novos de AVC e IM atendidos em Pronto Socorro de um hospital de clínicas e valores de temperatura e monóxido de carbono. Conclui-se que das internações anuais por IM, 2,1% são devidos à poluição atmosférica e 4,9% a altas temperaturas. Das internações anuais por AVC, 2,8% são devidas a altas temperaturas. Não foi identificado associação entre monóxido de carbono e AVC.Many studies have been published about the relationship between life style and genetic risk factors and stroke and heart attack, but there have been few about the relationship between atmospheric pollution, specifically with carbon monoxide, and temperature and stroke and heart attack. With a view to filling this gap the relationship between values of carbon monoxide concentration in the air, maximum and average by day, and maximum temperature by day and the number of new cases of CVA and IM admitted as emergencies at the biggest hospital complex of S. Paulo city was analysed. If was concluded, by the use of multivariable regression analysis, that 2.1% and 4.9% of heart attack admissions were due to carbon monoxide air pollution and high temperature, respectively. 2.8% of stroke admissions were due high temperature. Stroke and carbon monoxide were not associated in this population.

Las maclas de calcita en los metacarbonatos. Significado tectónico y su empleo para la determinación de temperaturas de deformación

Directory of Open Access Journals (Sweden)

Dámaso Cáceres-Govea

2009-03-01

Full Text Available Las maclas de calcita han sido utilizadas para la estimación de las temperaturas de deformación a las que fueron sometidas las rocas metacarbonatadas, basado en los diferentes tipos que pueden aparecer bajo ciertas condiciones de temperaturas. Se escogió un perfil en la cúpula de Trinidad, macizo Escambray, Cuba central, donde afloran rocas metamorfizadas en facies de esquistos verdes (napes La Sierrita y Yaguanabo, y rocas de alta presión (nape Monforte. En el nape de alta presión predominan las maclas tipo III sólo en granos aislados relícticos; la existencia de carbonato de calcio muy fino y no maclado, evidencia su formación después del pico metamórfico. En las unidades de esquistos verdes predominan las maclas de tipo II en granos orientados en S2, formadas a temperaturas entre 200-350 °C. Pueden aparecer maclas de tipo III y ocasionalmente de tipo IV que indican incrementos de temperatura durante D2. La existencia de venas tardías con maclas de tipo I, la formación de series de maclas finas dentro de maclas de tipo II y la existencia de granos no maclados, señalan un decremento de la temperatura hacia finales de la fase D2. Las maclas analizadas responden principalmente a procesos de subducción-colisión y exhumación más que a al proceso de subducción, en el cual estuvo insertado el macizo Escambray durante el Cretácico Campaniano. Conjuntamente, las deformaciones de micas, plagioclasas, cuarzo y epidota en muestras poliminerales demuestran que las temperaturas de deformación de las secuencias estuvieron alrededor de los 400 °C.

Evidence of weak pair coupling in the penetration depth of bi-based high-Tc superconductors

International Nuclear Information System (INIS)

Thompson, J.R.; Sun, Yang Ren; Ossandon, J.G.; Christen, D.K.; Chakoumakos, B.C.; Sales, B.C.; Kerchner, H.R.; Sonder, E.

1990-01-01

The magnetic penetration depth λ(T) has been investigated in Bi(Pb)SrCaCuO high-T c compounds having 2- and 3-layers of copper-oxygen per unit cell. Studies of the magnetization in the vortex state were employed and the results were compared with weak and strong coupling calculations. The temperature dependence of λ is described well by BCS theory in the clean limit, giving evidence for weak pair coupling in this family of materials. For the short component of the λ tensor, we obtain values of 292 and 220 nm (T = 0) for Bi-2212 and (BiPb)-2223, respectively

Fotossíntese e fotoinibição em mogno e acariquara em função da luminosidade e temperatura foliar

OpenAIRE

Dias,Daniela Pereira; Marenco,Ricardo Antonio

2007-01-01

A fotoinibição pode ser intensificada por fatores de estresse como alta temperatura. O objetivo deste trabalho foi determinar os efeitos da luminosidade e temperatura na fotossíntese e na recuperação da fotoinibição sob baixa irradiância em mogno (Swietenia macrophylla King) e acariquara (Minquartia guianensis Aubl.). As plantas cresceram sob baixa irradiância: 0,20 (acariquara) e 1,43 mol m-2 dia-1 (mogno). A fotossíntese líquida e as características da fluorescência foram avaliadas em duas ...

Texturing of superconducting Bi-Pb-Sr-Ca-Cu-O ceramics by combining the effect of a magnetic field and hot pressing in one direction; Texturation des ceramiques supraconductrices Bi-Pb-Sr-Ca-Cu-O par combinaison des effets du champ magnetique et de la contrainte uniaxiale a haute temperature

Energy Technology Data Exchange (ETDEWEB)

Noudem, J G

1995-10-27

Superconducting Bi-(Pb)-Sr-Ca-Cu-O (Bi:2223) ceramics have a weak 77 K transport critical current density (Jc) due to porosity and the presence of misaligned platelets. In order to obtain higher critical current densities in these materials, it is necessary to increase their density and induce a preferential crystallographic orientation. We have developed a texturing process using solidification in a magnetic field combined with hot pressing. The experimental set-up provides a uniaxial pressure of 60 MPa and temperature up to 1100 deg C in a magnetic field of 8 T. Magnetic melt texturing (MMT) proved to be very effective in producing bulk oriented samples of polycrystalline Bi:2223 (crystallite c-axis oriented parallel to the field direction). These samples have Jc values of up to 1450 A/cm{sup 2} and a density of 5.1 g/cm{sup 3}. The texturing by hot pressing (HP) gives homogeneous, dense ({approx} 6 g/cm{sup 3}; 95 % of the theoretical limit) ceramics with a Jc of 2500 A/cm{sup 2}. Tapes of Ag/Bi:2223 provided by Alcatel Alsthom were also successful textured using HP. Finally we have demonstrated that the combination of solidification in a magnetic field with hot pressing (MMHPT) improves both the texture and density of the samples. Moreover the samples are very homogeneous and mechanically resistant. The 77 K transport critical current densities have values up to 3800 A/cm{sup 2} and 1100 A/cm{sup 2} along the (ab) and c-axis respectively. We have demonstrated that these samples are of potential use a current limiters. (author) 146 refs.

Reaction products between Bi-Sr-Ca-Cu-oxide thick films and alumina substrates

International Nuclear Information System (INIS)

Alarco, J.A.; Ilushechkin, A.; Yamashita, T.; Bhargava, A.; Barry, J.; Mackinnon, I.D.R.

1997-01-01

The structure and composition of reaction products between Bi-Sr-Ca-Cu-oxide (BSCCO) thick films and alumina substrates have been characterized using a combination of electron diffraction, scanning electron microscopy and energy dispersive X-ray spectrometry (EDX). Sr and Ca are found to be the most reactive cations with alumina. Sr 4 Al 6 O 12 SO 4 is formed between the alumina substrates and BSCCO thick films prepared from paste with composition close to Bi-2212 (and Bi-2212+10 wt.% Ag). For paste with composition close to Bi(Pb)-2223 +20 wt.% Ag, a new phase with f.c.c. structure, lattice parameter about a=24.5 A and approximate composition Al 3 Sr 2 CaBi 2 CuO x has been identified in the interface region. Understanding and control of these reactions is essential for growth of high quality BSCCO thick films on alumina. (orig.)

The SLIMITRE system: T-P-CCL registry in high temperature oil wells; El sistema SLIMITRE: registro T-P-CCL en pozos petroleros de alta temperatura

Energy Technology Data Exchange (ETDEWEB)

Iglesias R, Eduardo and others [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2001-07-01

PEMEX Exploration and Production (PEP), through its Management of Well Productivity of the Subdivision of Technology and Professional Development (GTDP) and of its Active Luna, faced the problematic of carrying out simultaneous recordings of temperature and pressure in high temperature flowing wells. Capitalizing the experience and know-how of the Gerencia de Geotermia (GG) of the Instituto de Investigaciones Electricas (IIE) in this field, it ordered the resolution of the described problematic, by means of the development of appropriate tools. In order to compliment this order, the GG of the IIE developed the SLIMETRE system, in close collaboration with the personnel of PEP involved in the project. This project framed in the Agreement of Collaboration for the rendering of services between PEMEX Exploration and Production and the Instituto de Investigaciones Electricas. In the sections that follow appear the main parameters of design, the architecture of the system is explained, the tools and the subsystem of data acquisition are described; the obtained results are exposed and the conclusions appear. [Spanish] Pemex Exploracion y Produccion (PEP), a traves de su Gerencia de Productividad de Pozos de la Subdireccion de Tecnologia y Desarrollo Profesional (GTDP) y de su Activo Luna, encaro la problematica de efectuar registros simultaneos de temperatura y presion en pozos fluyentes de alta temperatura. Capitalizando la experiencia y know-how de la Gerencia de Geotermia (GG) del Instituto de Investigaciones Electricas (IIE) en dicho campo, le encargo la resolucion de la problematica descrita, mediante el desarrollo de herramientas apropiadas. Para cumplimentar dicho encargo, la GG del IIE desarrollo el sistema SLIMETRE, en estrecha colaboracion con el personal de PEP involucrado en el proyecto. Este proyecto se enmarco en el Convenio de Colaboracion para la prestacion de servicios entre Pemex Exploracion y Produccion y el Instituto de Investigaciones Electricas. En

Influence of powder pre-annealing on the phase formation and critical current of Bi-2223/Ag tapes

DEFF Research Database (Denmark)

Chen, X.P.; Grivel, Jean-Claude; Li, M.Y.

2004-01-01

. The effects of different precursors were investigated by XRD, SEM/EDS and critical current measurements. It has been found that both the microstructure and phase formation depended strongly on the different lead-rich phases, which determined the reactivity of the precursor. Tapes fabricated using...... the precursor with Ca2PbO4 phase (tape T1) had lower transformation rate of 2223 phase than tapes fabricated using the precursor with 3321 phase (tape T2). SEM results show that a large fraction of secondary phases with big particle size was formed in the tape T1 during the subsequent sintering, which might...

Influencia de la temperatura de termoterapia: el rendimiento del cultivo del ajo

OpenAIRE

Varés Megino, Luis; Correa Hernando, Eva Cristina; Iglesias Gonzalez, Concepcion; Palmero Llamas, Daniel

2009-01-01

La termoterapia se ha comprobado que es un método eficaz y de fácil aplicación para la erradicación de patógenos (bacterias, hongos, nemátodos, virus y fitoplasmas) tanto de semillas como de material vegetal utilizado en la reproducción vegetativa. Este método se basa en la susceptibilidad digerencial entre el hospedante y sus parásitos internos o externos en relación con las altas temperaturas. Uno de los métodos de termoterapia más usado es el tratamiento por agua caliente a causa de la mej...

Síntese e caracterização de perovesquites do sistema BiFeO3

OpenAIRE

Carvalho, Teresa Maria Tranchete de

2007-01-01

Dissertação de Mestrado em Física e Química para o Ensino, apresentada à Universidade de Trás-os-Montes e Alto Douro Os materiais multiferróicos, como o caso do BiFeO3, são bastante promissores em termos tecnológicos, possuindo uma potencial aplicação em sensores, memórias não voláteis e actuadores. A perovesquite BiFeO3 apresenta vantagens relativamente a outros compostos multiferróicos: elevada temperatura de Curie (TC=1100 K); elevada temperatura de Néel (TN=640 K); não contém chumbo...

Comparison of electromechanical properties and lattice distortions of different cuprate high temperature superconductors

CERN Document Server

Scheuerlein, C.; Grether, A; Rikel, M O; Hudspeth, J; Sugano, M; Ballarino, A; Bottura, L

2016-01-01

The electromechanical properties of different cuprate high-temperature superconductors, notably two ReBCO tapes, a reinforced and a nonreinforced Bi-2223 tape, and a Bi-2212 wire, have been studied. The axial tensile stress and strain, as well as the transverse compressive stress limits at which an irreversible critical current degradation occurs, are compared. The experimental setup has been integrated in a high-energy synchrotron beamline, and the self-field critical current and lattice parameter changes as a function of tensile stress and strain of a reinforced Bi-2223 tape have been measured simultaneously. Initially, the Bi-2223 filaments exhibit nearly linear elastic behavior up to the strain at which an irreversible degradation is observed. At 77 K, an axial Bi-2223 filament precompression of 0.09% in the composite tape and a Bi-2223 Poisson ratio ν = 0.21 have been determined.

Solid state compatibility in the ZnO-rich region of ZnO-Bi2O3-Sb2O3 and ZnO-Bi2O3-Sb2O5 systems

Directory of Open Access Journals (Sweden)

Jardiel, T.

2010-04-01

resultado se ha observado un comportamiento diferente al usar Sb2O3 o Sb2O5 como precursor de partida, lo cual debe atribuirse al proceso de oxidación experimentado por el compuesto Sb2O3 durante el calentamiento. Por otra parte, utilizando altas concentraciones de bismuto en la formulación de partida se llega a la formación de una fase líquida a temperaturas inferiores, lo que permitiría el empleo de temperaturas de sinterización más bajas.

Produção e estabilidade de conservação de farinha de acerola desidratada em diferentes temperaturas

Directory of Open Access Journals (Sweden)

Daíse Souza Reis

2017-04-01

Full Text Available Resumo O objetivo deste trabalho foi identificar a melhor temperatura de desidratação para a produção de farinha de acerola de alta qualidade de consumo e estabilidade de parâmetros físico-químicos durante a conservação. Frutos de acerola ‘Flor Branca’ foram colhidos no estádio de maturação maduro em um pomar comercial do Vale do São Francisco, Petrolina, PE. Frutos com ou sem sementes foram sanitizados e desidratados nas temperaturas de 60 °C, 70 °C e 80 °C em estufa de circulação de ar forçado e, em seguida, foram triturados para a obtenção da farinha, a qual foi armazenada em temperatura ambiente em embalagens de polietileno herméticas. A polpa dos frutos foi utilizada para a determinação do pH, sólidos solúveis (SS, acidez titulável (AT, ácido ascórbico (AA e umidade. A farinha de acerola foi avaliada a cada 15 dias, por um período de 75 dias, quanto ao pH, SS, AT, AA e cor. Para todas as temperaturas de desidratação, os valores de pH e SS foram semelhantes, variando entre 3,5-4,2 e 6,3-11,7, respectivamente. Os SS apresentaram menor variação ao final do armazenamento. A AT aumentou em todas as amostras variando de 5% a 10%. As perdas de ácido ascórbico foram de 76,2% e 80%, 23,9% e 55%, ou 37,9% e 65% para as farinhas com e sem sementes desidratadas a 60 °C, 70 °C e 80 °C, respectivamente. De acordo com os resultados obtidos, a melhor temperatura de desidratação é 70 °C, pois resultou em farinha com alta qualidade de consumo e estabilidade de parâmetros físico-químicos durante 75 dias de conservação.

Temperatura, Oximetría Cerebral y Disfunción Cognitiva Postoperatoria (DCPO) en pacientes intervenidos de Prótesis Total de Rodilla (PTR) con anestesia intradural. Estudio prospectivo

OpenAIRE

Salazar Garcia, Fátima

2015-01-01

Introducción: La Disfunción cognitiva postoperatoria (DCPO) tiene una alta incidencia en pacientes de cirugía ortopédica. Durante la anestesia y la cirugía se produce un descenso progresivo de la temperatura. Esta hipotermia tiene efectos deletéreos pero también puede tener un efecto protector cerebral. Nosotros planteamos la hipótesis que la temperatura perioperatoria puede tener un impacto sobre la aparición de DCPO. Por otro lado, la monitorización de la saturación regional cerebral de...

The effect of long annealing on Pb-doped high-Tc Bi-Sr-Ca-Cu-O systems

Energy Technology Data Exchange (ETDEWEB)

Chandra, S.; Agnihotry, S.A.; Asthana, P.; Nagpal, K.C.; Saini, K.K.; Chanderkant; Sharma, C.P.; Ekbote, S.N. (National Physical Lab., New Delhi (India))

1991-01-16

The lead doped Bi based copper oxide high-Tc superconductors with different nominal compositions and with different annealing time periods are studied. The highest Tc (zero) achieved is 112 K in bulk phase 2223. The varying intensity of the low angle line at 2{theta}{approx equal}4.7deg suggests the gradual formation of the high-Tc phase due to the long annealing of nearly 200 to 250 h. It is also found that the high-Tc phase starts degrading after 250 h of annealing and Tc reduces. The distortion of the 2223 phase is suggested by the broadening of different XRD peaks, also the SEM studies support the above contention. The EDAX studies show no presence of Pb in the crystallites. (orig.).

The off-stoichiometric Bi1.8Pb0.3Sr2Ca2Cu3.3Ox target for thin films

International Nuclear Information System (INIS)

Harabor, A.; Deletter, M.

1996-01-01

X-ray diffraction (XRD), EDAX, AC susceptibility and resistivity measurements has been used as characterization methods for the Bi-2223 monophase target with the starting stoichiometry Bi 1.8 Pb 0.3 Sr 2 Ca 2 Cu 3.3 O x . Pressure parameter is playing an important role in obtaining good superconducting properties for this compound. Critical currents and activation energy has been calculated from susceptibility and magnetoresistivity curves, respectively. The results could be interpreted in terms of TAPS and TAFF models. (orig.)

Growth, characterization, and physical properties of Bi-Sr-Ca-Cu-O superconducting whiskers

International Nuclear Information System (INIS)

Kraak, W.; Thiele, P.

1996-01-01

Single crystal whiskers of the Bi-based high-T c superconductors have been grown directly from the stoichiometric melt. Conditions for the preferable growth of the (2212) phase and annealing conditions for the conversion from the (2212) phase to the (2223) and (2234) Bi-based superconducting phases are achieved. The orientation and chemical composition of the crystals were characterized by X-ray diffractometry and energy dispersive X-ray analysis. Characteristic structural properties of the whiskers (incommensurable modulation in b-direction, peculiarities of dislocation networks) have been revealed by transmission electron microscopy and electron diffraction. Some special features of the broad superconducting transition in multiphase whiskers have been examined by spatially resolved measurements using low-temperature scanning electron microscopy. (orig.)

Comportamiento eléctrico del compuesto Bi5FeTi3O15 y de sus soluciones sólidas con CaBi4Ti4O15

Directory of Open Access Journals (Sweden)

Durán, P.

1999-12-01

Full Text Available Bi5FeTi3O15 (BiFT compound has been prepared by solid state reaction between the corresponding oxides. Its crystalline structure has been established by X ray Diffraction, (XRD. Ceramic samples with apparent density > 95% Dth have been sintered. On these samples, electrical conductivity and Curie temperature have been measured. Solid solutions of Bi5FeTi3O15 (BiFT and CaBi4Ti4O15 (CBiT have been prepared. On poled samples of these solid solutions, piezoelectric parameters have been established. The BiFT compound shows electrical conductivity values very similar to those of the Bi4Ti3O12 (BiT compound. The electrical conductivity of solid solutions is a function of CBiT amount. A possible electrical conductivity mechanism which is different of that accepted for the BiT compound is discussed.Se ha preparado Bi5FeTi3O15 (BiFT por reacción en estado sólido de los óxidos correspondientes. Se ha determinado su estructura cristalina por Difracción de Rayos X (DRX. Se han preparado compactos sinterizados con densidades superiores al 95%. Se ha determinado su temperatura de Curie, y la conductividad eléctrica entre 150 y 850ºC. Se han preparado soluciones sólidas de Bi5FeTi3O15 con CaBi4Ti4O15, (CBiT y se han determinado los mismos parámetros de temperatura de Curie y de conductividad para ellas. En las soluciones sólidas se han determinado los parámetros Piezoeléctricos de muestras polarizadas Debe destacarse que el compuesto Bi5FeTi3O15 presenta unos valores de conducción eléctrica más próximos a los correspondientes al Bi4Ti3O12 (BiT que a los de los compuestos MeBi4Ti4O15. La conductividad eléctrica de las soluciones sólidas varía con el contenido de CBiT. Se discute la posible existencia de un modelo de conducción eléctrica que difiere del aceptado hasta el momento para el BiT, basado en los defectos localizados en las capas Bi2O2 2-.

Resistencia a la corrosión a alta temperatura de recubrimientos NiCrAlY y NiCrFeNbMoTiAl depositados por APS

Directory of Open Access Journals (Sweden)

José Luis Tristancho-Reyes

2014-12-01

Full Text Available La corrosión a alta temperatura de las tuberías utilizadas en equipos generadores de vapor (calderas ha sido reconocida como un grave problema que trae consigo el adelgazamiento de éstas y, por consiguiente, la falla de los equipos. En la última década se han incrementado las investigaciones que involucran recubrimientos protectores que ayudan de alguna manera a prolongar la vida útil de estos equipos. Esta investigación determinó el comportamiento de los recubrimientos NiCrAlY y NiCrFeNbMoTiAl depositados por proyección térmica asistida por plasma (APS sobre la aleación SA213 – T22 (2¼Cr – 1Mo, en un ambiente corrosivo de 80%V2O5–20%K2SO4 a 800°C. Los valores de la cinética de corrosión fueron determinados mediante resistencia a la polarización lineal (RPL y espectroscopia de impedancia electroquímica (EIE. Los resultados obtenidos muestran una menor cinética de corrosión en el recubrimiento NiCrFeNbMoTiAl que la presentada por el recubrimiento NiCrAlY, corroborado por Microscopia Electrónica de Barrido (MEB.

Microestructura y propiedades mecánicas de conductores protónicos de alta temperatura crecidos por fusión de zona flotante

Directory of Open Access Journals (Sweden)

López Robledo, M. J.

2004-08-01

Full Text Available High temperature protonic conductors (HTPC were successfully fabricated by melt growth using the laser heated floating zone method (SrCe0.9Y0.1O3-δ, SrCe0.8Y0.2O3-δ, SrZr0.9Y0.1O3-δ, SrZr0.8Y0.2O3-δ, Sr3(Ca1.18Nb1.82O9-δ and SrTi0.95Sc0.05O3-δ. Microstructural characterization was performed by scanning and transmission electron microscopy (SEM, TEM. The materials have a cellular microstructure, with cell width ranging between 10-50 μm and intercellular regions up to 1 μm thick. The diffraction analysis indicates that the cells are crystalline, and the intercellular regions are amorphous. TEM reveals that the cells present multiple planar defects, separating rotated regions with of same crystallographic structure. The high temperature mechanical properties were studied by compression tests performed under constant strain rate and constant load. Remarkable high temperature strengths of 500 MPa at 700 oC, 400 MPa at 1100 oC and 370 MPa at 1300 oC were measured, being the plastic deformation evident at 1100 ºC and 1300 ºC. The best mechanical behavior was obtained for the systems Sr3(Ca1.18Nb1.82O9-δ and SrZr0.9Y0.1O3-δ. The strengths and creep resistance of these systems are better than the ones of polycrystalline HTPC ceramics of similar structure and composition. After the mechanical tests, the samples were studied by SEM and TEM. The fracture started to propagate following the intercellular regions. In the plastically deformed samples, dislocation activity was found.

Se han estudiado conductores protónicos de alta temperatura (CPAT fabricados por fusión de zona flotante asistida por láser (SrCe0.9Y0.1O3-δ, SrCe0.8Y0.2O3-δ, SrZr0.9Y0.1O3-δ, SrZr0.8Y0.2O3-δ, Sr3(Ca1.18Nb1.82O9-δ y SrTi0.95Sc0.05O3-δ. La caracterización microestructural se ha realizado mediante Microscopía Electrónica de Barrido y Transmisión (MEB, MET. Los materiales tienen una estructura celular, con células de anchuras entre 10-50 μm y regiones

Oxidación cíclica de un acero refractario AISI 310 a alta temperatura en atmósferas con contenidos de oxígeno variables

Directory of Open Access Journals (Sweden)

Higuera-Hidalgo, V.

2005-06-01

Full Text Available High temperature oxidation tests of an AISI 310 stainless steel was performed in two different environments: in an standard atmosphere (21 % oxygen at 704, 800, 884 and 1,000 °C and in the typical environment of a gas turbine and vapor generator of a combined-cycle electric generation unit (10 % oxygen at 800 and 1,000 °C. The oxidation kinetics was determined by means of the measurement of the weight gain per unit surface of the specimen and also determining the thickness of the oxide layer. Comparable results have been obtained using both methodologies and the effect of the oxygen content along with the other experimental differences were determined observing the oxidation kinetics in both environments. The cyclic oxidation of AISI 310 deteriorates at temperatures higher than 1,000 °C.

Se ha llevado a cabo un estudio experimental sobre la oxidación a altas temperaturas de un acero inoxidable refractario AISI 310, en dos ambientes diferentes: en una atmósfera convencional (21 % de O₂, a 704, 800, 884 y 1.000 °C y en un ambiente simulativo de una turbina de gas y del generador de vapor de uña central eléctrica de ciclo combinado (10-11 % de O₂, a 800 y 1.000 °C. La cinética de la oxidación del material se ha determinado a partir, tanto de la ganancia de peso por unidad de superficie experimentada por las probetas objeto de ensayo como por la determinación de los espesores de las capas de óxido formados. Se han obtenido resultados comparables con ambas metodologías y se ha puesto de manifiesto el efecto del contenido de oxígeno y de las demás diferencias experimentales a partir de la comparación de las cinéticas de oxidación del acero en los dos medios oxidantes analizados. La oxidación del acero AISI 310 en situaciones térmicas cíclicas empieza ya a ser importante a partir de una temperatura de 1.000 °C.

Tolerancia de temperatura

OpenAIRE

Sonnenholzner, Stanislaus

2002-01-01

Tolerancia de Temperatura La especie Litopenaeus (Penaeus) vannamei es un camarón tropical cultivado mundialmente en un amplio rango de temperaturas del agua (18º – 33ºC), sin embargo el valor óptimo descrito por varios autores para su cultivo se encuentra entre 28º a 31ºC.

Magnetism of Bi2Sr2Can-1CunO2n+4+δ (n = 1,2,3)

International Nuclear Information System (INIS)

Ishida, T.; Koga, K.; Kanoda, K.; Takahashi, T.

1992-01-01

The normal-state dc susceptibility χ dc of the Bi 2 Sr 2 Ca n-1 Cu n O 2n+4+δ (n=1, 2, 3) pellet is of the order of +10 -7 emu/g. A large Curie-Weiss component is found in χ dc and the ESR spin susceptibility χ ESR of the pulverized 2201, 2212 and 2223 samples but it almost disappears by annealing. The relative magnitudes of χ ESR to χ dc for the annealed powders are dissimilar among the three phases: ESR of the 2201 sample is silent, χ ESR of the 2212 phase has almost the same magnitude as χ dc and χ ESR of the 2223 phase is appreciable but smaller than χ dc . (orig.)

Determination of the fraction of amorphous phases in superconducting samples

International Nuclear Information System (INIS)

Gomes Junior, G.G.; Ogasawara, T.; Amorim, H.S.

2010-01-01

The study phase formation of high critical temperature superconducting (Bi, Pb) - 2223 by partial melting and recrystallization aims to improve the microstructure of the material. Was used for X-ray diffraction characterization of the phases present. The DDM method (Derivative Difference Minimization) was used for the refinement of structures, quantification of the phases and determination the fraction of this amorphous. The advantage this method is not necessary to introduce an internal standard to determine the amorphous fraction. Were observed in the powder precursor phases (Bi, Pb) 2 Sr 2 Ca 2 Cu 3 O x (Bi, Pb) -2223, 93% of the sample, Bi 2 Sr 2 CaCu 2 O y (Bi-2212) and Bi 2 Sr 2 CuO z (Bi-2201). The powder precursor was heat treated at 820-870 deg C. To minimize volatilization of lead, the material was placed in silver crucibles closed. To get a high recovery of (Bi, Pb) - 2223, the material was cooled slowly, due to slow kinetic of formation of this phase. We observed a partial recovery phase (Bi, Pb) -2223. (author)

Raman scattering study of phonons in Bi-based superconductor thin films

International Nuclear Information System (INIS)

Mejia-Garcia, C.; Diaz-Valdes, E.; Contreras-Puente, G.; Lopez-Lopez, J.L.; Jergel, M.; Morales, A.

2004-01-01

Raman spectra were obtained from samples of Bi-Pb-Sr-Ca-Cu-O (BPSCCO) thin films after varying several growth parameters, such as covering material, annealing time (t R ), annealing temperature (T R ), and nominal lead content (x). Thin films with the nominal composition Bi 1.4 Pb x Sr 2 Ca 2 Cu 3 O δ were grown on MgO substrates by a spray pyrolysis technique, followed by a solid state reaction. The results of Raman scattering measurements at room temperature show a series of vibrational optical modes within the range 300-900 cm -1 . The assignment of these modes was made by involving mainly the 2212 and 2223 phases and was confirmed by both X-ray diffraction and resistance in dependence of the temperature (R-T) measurements as well

Progress in development of tapes and magnets made from Bi-2223 superconductors

Science.gov (United States)

Balachandran, U.; Iyer, A. N.; Haldar, P.; Hoehn, J. G., Jr.; Motowidlo, L. R.

1995-01-01

Long lengths of (Bi,Pb)2Sr2Ca2Cu3O(x) tapes made by powder-in-tube processing have been wound into coils. Performance of the coils has been measured at temperatures of 4.2 to 77 K, and microstructures have been examined by x-ray diffraction and electron microscopy and then related to superconducting properties. A summary of recent results and an overview of future goals are presented.

Progress in development of tapes and magnets made from Bi-2223 superconductors

International Nuclear Information System (INIS)

Balachandran, U.; Iyer, A.N.; Motowidlo, L.R.

1994-05-01

Long lengths of (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O x tapes made by powder-in-tube processing have been wound into coils. The performance of these coils has been measured at temperatures of 4.2 to 77 K. Microstructures have been examined by X-ray diffraction and electron microscopy and have been related to superconducting properties. A summary of recent results and an overview of future goals are presented

Bean model and ac losses in Bi2Ca2Cu3O10/Ag tapes

International Nuclear Information System (INIS)

Suenaga, M.; Chiba, T.; Wiesmann, H.J.; Haldar, P.

1997-01-01

The Bean model is almost solely used to interpret ac losses in the powder-in-tube processed composite conductor, Bi 2 Sr 2 Ca 2 Cu 3 O 10 /Ag. In order to examine the limits of the applicability of the model, a detailed comparison was made between the values of critical current density J c for Bi(2223)/Ag tapes which were determined by standard four-probe-dc measurement, and which were deduced from the field dependence of the ac losses utilizing the model. A significant inconsistency between these values of J c were found, particularly at high fields. Possible sources of the discrepancies are discussed

Synthesis, processing behavior, and characterization of bismuth superconductors using freeze dried nitrate precursors

International Nuclear Information System (INIS)

Coppa, N.V.; Hults, W.L.; Smith, J.L.; Brynestad, J.

1994-01-01

The synthesis of Bi 2-x Pb x Sr 2 Ca 2 Cu 3 O 10 (Bi2223) powders from a freeze dried nitrate precursor is reported here. We examine the composition and morphology of the precursor material, describe the chemistry and kinetics of product formation, and evaluate the phase composition and superconducting properties of the products. A nitrate solution containing the appropriate ratio of cations was rapidly frozen and then freeze dried at low temperatures to form an atomic mixture of the component salts. The thermal processing of the freeze dried material consisted of three steps: (i) dehydration, (ii) denitration, and (iii) solid state reaction to form the Bi2223 superconducting product. Calcium substituted bismuthates and strontium-substituted calcium cuprate, not Bi2201, are the intermediates between the nitrates and the superconducting products. These highly disordered phases rapidly transform into Bi2212 or Bi2223 at higher temperatures (>790 degree C). The kinetics of product formation was studied using XRD analysis and magnetic susceptibility. The kinetics were shown to follow the nucleation and growth mechanism. Bi2223 formed after only 30 min at a few degrees below the melting point, and after 37 h Bi2223 products exhibited excellent phase composition and magnetic susceptibility characteristics

Positron annihilation study of the high-Tc (Bi, Pb)2Sr2Ca2Cu3Ox superconductor

International Nuclear Information System (INIS)

Lim, H.J.; Byrne, J.G.

1997-01-01

Positron lifetime spectroscopy (PLS) and positron Doppler-broadening spectroscopy (PDBS) were applied to the high-T c lead-doped Bi 2 Sr 2 Ca 2 Cu 3 O x (BPSCCO 2223) superconductor as a function of temperature. Neither positron lifetimes nor Doppler parameters (S, W, and S/W) showed significant change through T c . This may result from having the highest positron density in the open BiO 2 double layers and no significant positron density in the superconducting CuO 2 layers where positrons, if mainly present, are known to be sensitive to the transition in other high-T c superconductors. Doppler parameters showed that the probability of positron annihilations with core electrons in the lattice slightly increased and that the probability of positron annihilations with conduction electrons slightly decreased as temperature decreased from ambient temperature to 20 K. The lifetime associated with positron annihilations in the perfect lattice of the sample (τ 1 ) was 209 ps and, due to the annihilations at internal surfaces or voids in the sample (τ 2 ) was about 540 ps, independent of temperature. Finally, the mean lifetime for BSCCO 2223 was about 307 ps. (orig.)

Seed performance after exposure to high temperatures Desempenho de sementes após exposição a altas temperaturas

Directory of Open Access Journals (Sweden)

W. R. Silva

1998-01-01

Full Text Available In orthodox seed management, the application of temperatures over 42ºC is routinely associated with deterioration while biological behaviors in operations conducted under high temperatures are hardly ever studied. The results found, however, indicate the possibility of stationary drying of soybean seeds at 50ºC, provided that the insufflated air flow intensity is considered, as well as the reduction of B. brizantha seed dormancy submitted to 85ºC.No manejo de sementes ortodoxas, a aplicação de temperaturas superiores a 42ºC é, rotineiramente, associada à deterioração e raramente são estudados os comportamentos biológicos presentes em operações conduzidas sob temperaturas superiores. Resultados obtidos, contudo, indicam possibilidades de secagem estacionária de sementes de soja a 50ºC, desde que considerada a intensidade do fluxo do ar insuflado, e de redução na dormência de sementes de B. brizantha submetidas a 85ºC.

Superconductores de alta temperatura crítica Bi2Sr2CaCu2O8+δ altamente texturados: propiedades mecánicas

Directory of Open Access Journals (Sweden)

Llorca, J.

2000-12-01

Full Text Available The mechanical properties of Bi2Sr2CaCu2O8+δ superconductor fibres processed by laser-induced directional solidification at different growth rates were studied. Tensile and diametral compression (Brazilian test tests were performed to analyse the longitudinal and transversal strength. The elastic modulus was determined using the flexural vibration resonance method. Flexure tests were also carried out to compare with the literature data. In addition, polished sections of the as-received fibres and the fracture surfaces of the broken samples were analysed in the scanning electron microscope. The fibres were highly anisotropic and the transverse fibre strength was very low due to the early failure by cleavage of the grains perpendicularly to the c axis. The degree of anisotropy and the longitudinal strength increased as the fibre growth rate decreased while the transverse strength followed the opposite trend. This behaviour was due to changes in the porosity and the alignment of the crystals along the fibre axis.En este trabajo se han estudiado las propiedades mecánicas de fibras superconductoras Bi2Sr2CaCu2O8+δ fabricadas por solidificación direccional inducida por láser y crecidas a distintas velocidades. Se realizaron ensayos de tracción directa e indirecta (ensayo brasileño para evaluar la resistencia a tracción en las direcciones longitudinal y transversal respecto a la de crecimiento. El módulo elástico de las fibras en la dirección longitudinal se obtuvo midiendo la frecuencia fundamental de resonancia en flexión y se realizaron ensayos de flexión para comparar con los resultados disponibles en la literatura. El trabajo se completa con el estudio de las secciones longitudinales y transversales del material sin ensayar y el análisis fractográfico de las probetas rotas. Las fibras resultaron altamente anisótropas siendo su resistencia en la dirección transversal muy baja, debido a la fractura por clivaje de los planos

Effect of post-sintering treatment on properties of Bi-based high Tc superconductors

International Nuclear Information System (INIS)

Nagai, Masayuki; Kozuka, Akira; Morishita, Ken; Nishino, Tadashi; Hattori, Takeo; Takata, Masasuke

1989-01-01

A new method to obtain the pure 110K phase in the system Bi-Sr-Ca-Cu-O was examined employing post-sintering treatment. The mixture of Bi 2 O 3 , SrCO 3 , CaCO 3 and CuO with the basic composition of Bi/Sr/Ca/Cu=2/2/1/2 was calcined. The resulting powder was soaked in ethanol containing copper acetate and calcium acetate, the amounts of which were determined to give the composition of Bi/Sr/Ca/Cu=2/2/2/3 after sintering. The resistivity was measured by the d.c. four probe method in a cryostat. The current level was maintained at 50 mA and the voltage drop was determined by averaging the values in the forward and reverse directions. The zero T c ranged from 65 to 69K for the samples after sintering, while that ranged from 69 to 71K for those with post-sintering treatment. The effect of the treatment was not drastic but significant. Modified post-sintering treatment is being examined and the results are reported in the symposium

El estrés por temperatura provoca necrosis en tabaco negro; cuantificación por análisis de imágenes

Directory of Open Access Journals (Sweden)

Eduardo Ortega

2008-07-01

de imágenes ImageJ. Este programa es capaz de adquirir, mostrar, editar, resaltar y analizar imágenes. Se demostró que las hojas sometidas a 4 ºC, independientemente del tiempo de exposición, presentaron una mayor área necrosada (35% en comparación con el resto de los tratamientos. Las áreas con acumulación de H2O2 in situ fueron mayores en los tratamientos de estrés por temperaturas altas (45 y 60 oC. La detección y cuantificación de la necrosis producida por temperaturas extremas, combinando el método del azul de tripano con el análisis de imágenes, es una herramienta útil para valorar los daños producidos por estrés de temperaturas y pudiera ser utilizado para valorar los daños celulares provocados por otros tipos de estrés.Palabras clave: variedad-Habana-2000; especies reactivas de oxígeno; H2O2;; Habana-2000-variety; reactive oxygen species.

Por que Melipona scutellaris (Hymenoptera, Apidae forrageia sob alta umidade relativa do ar?

Directory of Open Access Journals (Sweden)

Marília D. e Silva

2011-06-01

Full Text Available Há evidências de que a temperatura do ar e a umidade relativa afetam a atividade de voo de espécies de abelhas sociais Meliponini. Em particular, as espécies grandes do gênero Melipona Illiger, 1806 responderiam de maneira mais estreita à variação na umidade relativa. Neste estudo defende-se o argumento de que a umidade relativa seja uma variável de confusão. Nesta linha de argumentação, também foi analisado o papel da coleta de pólen sobre o ritmo diário de forrageio. A robusta Melipona scutellaris (Latreille, 1811 foi usada como modelo e a atividade diária de voo e de forrageio de pólen foi medida em 12 colônias (4 colônias/hábitat, em três tipos de hábitats, que variam principalmente quanto à pluviosidade, na área de distribuição natural desta espécie (Floresta Pluvial, Floresta Sazonal e Transição Floresta Tropical-Cerrados. A maioria da atividade de voo acontece durante a manhã. A atividade de forrageio das colônias foi mais elevada nas primeiras horas do alvorecer, quando a umidade relativa também era alta, frequentemente associada a picos de coleta de pólen. A atividade de voo decresceu abruptamente durante as temperaturas altas ao redor do meio dia. A relação da atividade de voo com a umidade relativa foi altamente significativa e linear, contrastando com a relação significativa e unimodal com a temperatura. Na relação com o forrageio de M. scutellaris, a umidade relativa se configura como uma variável contingente, em hábitats tropicais úmidos, considerando os padrões diários de variação do microclima e de forrageio de pólen. Este último padrão também sustenta a hipótese de partição temporal de fontes florais de pólen.

VARIABILIDAD DE LA TEMPERATURA DE SUPERFICIES EN EL NW DE LA PROVINCIA DE NEUQUÉN A PARTIR DE INFORMCIÓN SATELITAL.

Directory of Open Access Journals (Sweden)

Marisa G. Cogliati

2008-12-01

Full Text Available La complejidad del terreno y la falta de datos meteorológicos siguiendo el gradiente altitudinal obliga a la exploración de nuevos métodos o esquemas entre los que se encuentra el análisis por medio de modelos o imágenes satelitales. El presente trabajo pretende describir el marco de información con el que se cuenta en el NW neuquino y la introducción de análisis espacial de distribución de la temperatura de superficie a partir de imágenes NOAA- AVHRR con miras a la inclusión futura de nuevos esquemas de estudio. La temperatura del aire presenta gran variabilidad espacial, principalmente en los valores mínimos, una idea de esta distribución puede asociarse a la temperatura de superficie que es obtenida a partir del análisis de imágenes NOAA-AVHRR. Este trabajo presenta el análisis de situaciones particulares de la temperatura de superficie de la zona NW de la Provincia de Neuquén utilizando imágenes de satélites NOAA en alta resolución (AVHRR e imágenes LANDSAT de la región. La temperatura de superficie obtenida utilizando la información de los canales 4 y 5 del sensor AVHRR presenta la distribución espacial de la temperatura del suelo que pone en evidencia la complejidad del comportamiento, asociado al relieve. Se observa la dependencia de las isotermas con la altura, alcanzando los menores valores de temperatura de superficie en los picos. Esta metodología permitiría incorporar información cuya escala consideraría con mayor detalle que en escala sinóptica de la temperatura de superficie de píxeles de aproximadamente 1 km2. El análisis posterior de una mayor cantidad de situaciones, permitiría realizar mapas estacionales de temperatura de superficie en una escala que no es posible obtener con el instrumental que se encuentra instalado en este momento, pudiendo asociarse posteriormente al comportamiento de la temperatura del aire.

Preparation of high - superconductor BSCCO in system with added Pb using method of synthesis Pechini

International Nuclear Information System (INIS)

Aguiar, Felipe Magalhaes de; Rodrigues, Vivian Delmute; Paula, Fernando Rogerio de

2014-01-01

This paper studied compound of the ceramic superconductor Bi-Sr-Ca-Cu-O (BSCCO). The predominant BSCCO system has four phases: Bi_2Sr_2CuO6 (Bi-2201), Bi_2Sr_2Ca_1Cu_2O_8 (Bi-2212), Bi_2Sr_2Ca_2Cu_3O_1_0 (Bi-2223) e Bi_2Sr_2Ca_3Cu_4O_1_2 (Bi-2234). Of these, the most studied is the Bi-2223 and this is due to present the highest critical temperature (Tc) (125K). However, this phase is more unstable and, therefore in this work we study the stabilization of Bi-2223 phase using the substitution method, in which Bi is replaced with the Pb. The samples were obtained by method of synthesis Pechini, the stoichiometry Bi_2_-_xPb_xSr_2Ca_2Cu_3O_y. The samples obtained were characterized by diffraction ray - X, electric measurement (RxT), Scanning electron microscope (SEM), Energy dispersive ray-x spectroscopy (EDX). The results showed that the best concentration of lead in phase and stabilizing Bi-2223 was the 0,40 mols obtaining the stoichiometry Bi_1_,_7_6Pb_0_,_2_0Sr_1_,_9_6Ca_2_,_1_8Cu_2_,_9_0O_y, which showed a T_c of 124 K. (author)

Thallium 2223 high Tc superconductor in a silver matrix and its magnetic shielding, hermal cycle and time aging properties

Energy Technology Data Exchange (ETDEWEB)

Fei, X.; He, W.S.; Havenhill, A. [and others

1994-12-31

Superconducting Tl{sub 2}Ba{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Tl2223) was ground to powder. Mixture with silver powder (0--80% weight) and press to desired shape. After proper annealing, one can get good silver-content Tl2223 bulk superconductor. It is time-stable and has good superconducting property as same as pure Tl2223. It also has better mechanical property and far better thermal cycle property than pure Tl2223.

Informe de personal de apoyo: Álvarez Martini, Carlos Alberto (2013-2014)

OpenAIRE

Alvarez Martini, Carlos Alberto

2014-01-01

Proyectos de investigación en los cuales colabora: - Metrología bi y tridimensional en el diseño, desarrollo y aplicación de concentradores ópticos solares para altas temperaturas. - Metrología en Salud Visual. “Análisis y Evaluación de Errores presentes en la utilización de Instrumentos Oftálmicos”. - Proyecto Red CYTED de intercambio iberoamericano: "Fomentar el uso de los si...

RELAÇÃO ENTRE TEMPERATURA DE SUPERFÍCIE TERRESTRE, ÍNDICES ESPECTRAIS E CLASSES DE COBERTURA DA TERRA NO MUNICÍPIO DE GOIÂNIA (GO

Directory of Open Access Journals (Sweden)

Silvio Braz de SOUSA

2012-12-01

Full Text Available Partindo-se do conceito de heterogeneidade da paisagem urbana, espera-se que diferentes paisagens apresentem distintos comportamentos termais, visto que, cada espaço da cidade possui particularidades quanto aos tipos e intensidades de cobertura e uso da terra. O presente trabalho, tendo como área de estudo o município de Goiânia, capital do estado de Goiás, busca analisar a relação dos diversos tipos de uso e intensidade de urbanização com o comportamento térmico superficial e, sua correlação com índices espectrais (NDBI e SAVI, utilizando para isso dados do sensor ETM+ abordo do satélite Landsat 7. Foram efetuadas amostragens aleatórias e utilizado como referência para a definição de uso e cobertura da terra uma imagem de alta resolução do satélite Quickbird. NDBI e temperatura de superfície terrestre apresentaram boa correlação (r² de 0,74. Áreas com cobertura de solo exposto, como áreas de plantio, queimadas e bairros sem cobertura asfáltica registraram altas temperaturas (maiores que 38 ºC. As temperaturas amenas registradas (< 23 e 30 ºC correspondem a áreas de vegetação densa, como as matas de galerias, o Jardim Botânico e o Parque Estadual Altamiro de Moura Pacheco, registrou-se uma diferença de até 8ºC em relação a áreas antropizadas.

AC Losses in Bi2Sr2Ca2Cu3O10+x Tapes and a 3.15-m-Long Single-Phase Cable

DEFF Research Database (Denmark)

Juul, Jeppe Søgaard; Mølgaard, Esben Tore; Jensen, Jens

2011-01-01

The alternating-current losses in superconducting multifilament BiSCCO-2223 tapes and a 3.15-m single-phase test cable were measured at 77 K using an electrical transport method. The cable had an inner diameter of 42 mm; it was composed of a single layer of 31 multifilament tapes and had a critic...

Effect of Sintering Time on Superconducting Wire Bi-Pb-Sr-Ca-Cu-O With Dopant MgO Sheated Ag Using Powder in Tube Method

Directory of Open Access Journals (Sweden)

Hariyati Lubis

2018-01-01

  DAFTAR PUSTAKA Abbas M.M., Abass L.K and Salman U., (2012, Influences of Sintering Time on the Tc of Bi2-xCuxPb0.3Sr2Ca2Cu3010+ High Temperature Superconductors, Energy Procedia 18, 215-224  Abbas, M.M., Abbas, L.K., Bahedh, H.S. 2015. Superconducting Properties of Bi2-SbxPb0,3Sr1,9Ba0,1Ca2Cu3O10+δ Compounds. Journal of Applied Science Research. 11. 22: 164-172 Darsono, N., Imaduddin, A., Raju, K., Yoon, D.H., (2015, Synthesis and Characterization of Bi1.6Pb0.4Sr2Ca2Cu3O7 Superconducting Oxide by High-Energy Milling, J Supercond Nov Magn. E. Chew,. (2010, Superconducting Transformer Design And Construction, University of Canterbury, Christchurch, New Zealand. March Hamadneh, I., Halim, S. A., dan Lee, C. K., (2006,  Characterization of Bi1.6Pb0.4Sr2Ca2Cu3Oy Ceramic Superconductor Prepared Via Coprecipitation Method at Different Sintering Time, J. Mater. Sci, 41: 5526-5530. Hermiz G.Y., Aljurani B.A., Beayaty M.A., (2014, Effect of Mn Substitution on the Superconducting Properties of Bi1.7Pb0,3Sr2Ca2-xMnxCu3O10+, International Journal Of Engineering and Advanced Technology (IJEAT. 3. 4: 213-217 John R Hull, (2003, Applications of high-temperature superconductors in power technology, Reports on Progress in Physics, Volume 66, Number 11 Lu, X.Y., Yi, D., Chen, H., Nagata, A. 2016. Effect of Sn, MgO and Ag2O mix-doping on the formation and superconducting properties of Bi-2223 Ag/tapes. Physics Procedia. 81: 129-132 Meretliev Sh., Sadykov K.B., Berkeliev A., (2000, Doping of High Temperature Superconductors, Turk J Phy.24: 39-48 Mohammed, N. H., Ramadhan A., Ali I. A., Ibrahim, I. H., dan Hassan, M. S, (2012, Optimizing the Preparation Conditions of Bi-2223 Superconducting Phase Using PbO and PbO2, Materials Sciences and Applications, 3: 224-233. Roumie, M., Marhaba, S., Awad R., Kork M., Hassan I., Mawassi R., (2014, Effect of Fe2O3 Nano-Oxide Addition on the Superconducting Properties of the (Bi,Pb-2223 Phase, Journal of Supercond Nov Magn, 27: 143-153 Serkan

Phase equilibria and homogeneity range of the high temperature superconducting compound (Bi,Pb)2+xSr2Ca2Cu3O10+δ

International Nuclear Information System (INIS)

Kaesche, S.

1995-01-01

For the superconducting cuprates (Bi,Pb) 2+x Sr 2 Ca 2 Cu 3 O 10+y phase equilibria, the homogeneity region, and the phase formation has been studied in the temperture range 800 to 890 C. Sintered samples were prepared by a solid state reaction starting from Bi 2 O 3 , PbO, CuO and carbonates CaCO 3 and SrCO 3 in a three-stage calcination process. For the phase identification polarization microscopy, X-ray diffraction and susceptibility measurements have been applied. Multi-phase regions were determined in the cross section of the quasi-ternary system (Bi,Pb) 2 O 3 -SrO-CaO-CuO with constant Bi/(Bi+Pb) ratio 0.84 taking into account the 2223-phase. The homogeneity region was determined as function of Sr, Ca, Bi and Pb concentration. Its maximum size was found at 850 C

Thallium 2223 high T(sub c) superconductor in a silver matrix and its magnetic shielding, hermalcycle and time aging properties

Science.gov (United States)

Fei, X.; He, W. S.; Havenhill, A.; Ying, Z. Q.; Xin, Y.; Alzayed, N.; Wong, K. K.; Guo, Y.; Reichle, D.; Lucas, M. S. P.

1995-01-01

Superconducting Tl2Ba2Ca2Cu3O10 (Tl2223) was ground to powder. Mixture with silver powder (0-80% weight) and press to desired shape. After proper annealing, one can get good silver-content Tl2223 bulk superconductor. It is time-stable and has good superconducting property as same as pure Tl2223. It also has better mechanical property and far better thermal cycle property than pure Tl2223.

AC loss characteristics of Bi2223/Ag sheathed tape wires subjected to mechanical strains and stresses

International Nuclear Information System (INIS)

Tsukamoto, Osami; Li, Z

2007-01-01

The influence of uniaxial tensile stress-strain on the AC loss characteristics of multifilamentary Bi2223/Ag sheathed tape wires was investigated. The uniaxial tensile stress-strain was applied to the sample wire in liquid nitrogen at atmospheric pressure, and the AC losses (transport, magnetization and total losses) were measured by an electric method. Two kinds of wire, oxide-dispersion strengthened Ag-alloy sheathed and Ag-alloy sheathed wires, were tested. The stress-strain curves of the tested wires were divided in three regions, i.e. elastic deformation, continuous plastic deformation and serrated-like plastic deformation regions, though the ranges of those regions were different for different kinds of wire. In the elastic and continuous plastic regions, the stress-strain curve was smooth and continuous, and in the serrated-like plastic region, the curve was rough. In the serrated-like plastic region, the wires kept elongating, while increase of the tensile stress was suspended. Dependences of the critical currents on the stress-strain were generally as follows. While decreases of the wire critical currents were in the range of less than 4% of the original values of the no-stress condition, the critical currents of the wires were reversible, that is, the critical currents recovered the original values at zero stress when the stress were released, regardless of whether the wires were in the elastic or continuous plastic region. In the continuous plastic region, the critical currents decreased up to 10%-15% of the original values and the critical currents were irreversible when the degradations of the critical currents exceeded about 4%. In the serrated-like plastic regions, the critical currents were more severely degraded. The AC loss characteristics of the wires are different in those regions. In the elastic and continuous plastic regions, the absolute values of AC losses were dependent on the stress-strain. However, the dependences of those normalized

Recent development of drastically innovative BSCCO wire (DI-BISCCO)

International Nuclear Information System (INIS)

Kikuchi, M.; Kato, T.; Ohkura, K.; Ayai, N.; Fujikami, J.; Fujino, K.; Kobayashi, S.; Ueno, E.; Yamazaki, K.; Yamade, S.; Hayashi, K.; Sato, K.; Nagai, T.; Matsui, Y.

2006-01-01

Up to this day, Ag-sheathed Bi2223 superconducting wires have been widely investigated and the long wires about 1000 m have been produced by using powder-in-tube (PIT) method on a commercial basis in the various facilities or companies. Although the wires are used for some applications such as HTS cables, magnets, motor and so on, the Bi2223 wires not only require much more improvements of the superconducting properties such as critical current, mechanical properties, but also longer and more uniform wires. Recently, the performances of Bi2223 wires have been drastically improved by using Controlled Over Pressure (CT-OP) sintering process. CT-OP process increased critical current (I c ) by more than 60% at 77 K and self field and improved the mechanical strength by more than 70%. The maximum I c was increased up to 166 A. These drastic improvements were caused by the higher density of Bi2223 filament up to almost 100% and better connectivity of the Bi2223 grains. The dense structure of the Bi2223 filaments prevents the ballooning phenomenon which is caused by the gasification of the trapped liquid nitrogen during temperature rise. Additionally, higher uniformity and higher production yield of long length wire were also achieved by exterminating defects during sintering. These high performance levels in CT-OP wires have contributed commercial level applications. We call as Drastically Innovative BSCCO (DI-BSCCO)

Tolerância ao sal e às altas temperaturas de estirpes de Sinorhizobium provenientes de zonas secas do Alentejo Salt and temperature tolerance of Sinorhizobium strains isolated from dry environments in Alentejo

Directory of Open Access Journals (Sweden)

P. Fareleira

2007-07-01

Full Text Available O trabalho teve como principal objectivo a obtenção de estirpes de rizóbio adequadas à nodulação de luzernas anuais e adaptadas a sobreviver nas condições ambientais susceptíveis de ocorrer em solos degradados. Dado que as populações de rizóbio apresentam variabilidade considerável no que respeita à tolerância a factores ambientais, os estudos focaram-se na pesquisa e na selecção de estirpes resistentes a condições adversas. Efectuaram-se colheitas de solos em diversas zonas no sul do País, seleccionando-se locais afectados por secura, temperaturas elevadas e, pontualmente, salinidade. A partir destes solos, isolaram-se estirpes de rizóbio, usando como planta hospedeira a luzerna anual Medicago polymorpha. Estudaram-se os efeitos de condições de stresse ambiental, como a salinidade e as altas temperaturas, no crescimento das estirpes isoladas. Dos 41 isolamentos analisados, 11 apresentaram crescimento em meio con-tendo 1,4 M de cloreto de sódio e suplementado com 10% de extracto de terra, e 22 cresceram quando incubadas a 45 ºC em meio sem aditivos. Três estirpes mostraram ter capacidade para crescer sob os efeitos conjuntos da salinidade e da alta temperatura. A análise de extractos etanólicos de estirpes tolerantes à salinidade revelou, na maior parte dos casos, a acumulação, induzida pelo sal, dos solutos compatíveis de Sinorhizobium: o dipéptido N - acetilglutaminilglutamina amida, vários tipos de betaínas, trealose, glutamato e prolina. A observação, por NMR de 31P in vivo, de uma estirpe tolerante ao sal, proveniente de um solo xistoso de baixo teor em fósforo, mostrou a presença de níveis elevados de reservas intracelulares de fosfato inorgânico (polifosfato, sugerindo um bom potencial para utilização em solos onde os riscos de salinização se conjuguem com deficiências em fósforo assimilável.The main objective of this work was to obtain rhizobial strains able to nodulate annual medics and

Li-promoted sodium zirconate as a CO{sub 2} absorbent at high temperatures; Zirconato de sodio promovido con Li como absorbente de CO{sub 2} a alta temperatura

Energy Technology Data Exchange (ETDEWEB)

Guzman Velderrain, V.; Barraza Jimenez, D.; Lardizabal Gutierrez, D.; Delgado Vigil, D.; Salinas Gutierrez, J.; Lopez Ortiz, A.; Collins-Martinez, V. [Centro de Investigacion en Materiales Avanzados S. C., Chihuahua, Chihuahua (Mexico)]. E-mail: virginia.collins@cimav.edu.mx

2009-09-15

structures of the type Na{sub 4}ZrO{sub 4}, which are responsible for the increase in the absorption capacity. [Spanish] En los procesos de produccion de hidrogeno a partir de combustibles fosiles, la captura de CO{sub 2} a alta temperatura ha alcanzado un papel esencial al convertir estos, en procesos energeticamente mas eficientes. Un ejemplo es el reformado de metano de vapor mejorado con absorcion (SER), donde la captura de CO{sub 2} a alta temperatura (600 grados centigrados) provee ahorros en energia ({approx_equal} 23%) sobre el proceso convencional de reformacion (SMR). Parte importante de este concepto es el absorbente solido de CO{sub 2}, el cual debe presentar una adecuada capacidad de absorcion y rapidas cineticas de absorcion/regeneracion. Recientemente, se han desarrollado absorbentes de CO{sub 2} sinteticos que consisten en mezclas de oxidos base-Li. Estudios previos realizados en nuestro laboratorio, reportan que el zirconato de sodio (Na{sub 2}ZrO{sub 3}) presenta propiedades de absorcion/regeneracion superiores a los oxidos base-Li. El presente trabajo tiene como objetivo aumentar la capacidad de absorcion del Na{sub 2}ZrO{sub 3} a alta temperatura sin afectar significativamente las cineticas tanto de absorcion como de regeneracion de este mediante su promocion con Li. El Na{sub 2}ZrO{sub 3} fue sintetizado por reaccion en estado solido e impregnado con LiNO{sub 3} a diferentes relaciones Li/Na: 0, 0.03, 0.05, 0.1 y 0.25 (NZ, NZL3, NZL5, NZL10, NZL25). La caracterizacion consistio en XRD y SEM. La evaluacion como absorbente se realizo mediante TGA a 600 grados centigrados en 80% CO{sub 2} (absorcion) y 800 grados centigrados en aire (regeneracion). Los XRD indican solo la estructura Na{sub 2}ZrO{sub 3} en todas las muestras, pero las promovidas presentan un desplazamiento en sus senales respecto a las del Na{sub 2}ZrO{sub 3}, el cual se atribuye a la sustitucion de atomos de Na por Li. Los resultados de TGA indican que la adicion del Li en la estructura del

Mejora en la producción de recubrimientos de NiAl obtenidos por síntesis autopropagada a alta temperatura mediante energía solar concentrada

Directory of Open Access Journals (Sweden)

Sierra, C.

2005-12-01

Full Text Available The production of NiAl coatings on steel can be achieved in a quick, cheap and unpolluted way. All this advantages are possible using concentrated solar energy (CSE and selfpropagating high-temperature synthesis (SHS. SHS process allows the production of NiAl in short periods of using of the heat released in the reaction. Initial energy is provided by concentrated solar energy. The aim of this work is to improve the adherence between steel and coating. Two kinds of samples are examined: samples with Ni powder layer, and samples electroplated with nickel.

Se presenta un procedimiento para la obtención de recubrimientos de NiAl sobre acero, de forma rápida, barata y limpia desde el punto de vista medioambiental. Todas estas ventajas son posibles mediante el empleo combinado de la Energía Solar Concentrada (CSE y la Síntesis Autopropagada a Alta Temperatura (SHS aplicada a la producción de intermetálicos. Las reacciones SHS permiten la obtención de NiAl en procesos de corta duración, prácticamente instantáneos, aprovechando la elevada exotermicidad de la propia reacción. El aporte energético inicial se realiza concentrando radiación solar con una lente de Fresnel. El objetivo del trabajo presentado era mejorar la adherencia del recubrimiento de NiAl al acero base; se comparan los resultados de los ensayos entre probetas con una capa intermedia de polvo de níquel y probetas con níquel electrodepositado.

Comunicaciones inalámbricas en ambientes hostiles: modelo de radio propagación y respuesta de elementos constitutivos de la parte terminal de la cadena de radio altas temperaturas

Directory of Open Access Journals (Sweden)

Jorge Avella Castiblanco

2010-01-01

Full Text Available En este trabajo se analiza y se propone una solución para evitar la disminución del rango de alcance de los sistemas de comunicación inalámbricos en robots de exploración para ambientes con temperaturas entre 873 K y 1273 K, dado que en este rango de temperaturas se encuentran situaciones como las presentes en los incendios urbanos. El estudio realizado cuantifica la influencia de tres factores de atenuación de la onda electromagnética: En primer lugar se analiza teórica y experimentalmente la atenuación debida a la variación de los parámetros constitutivos de un medio levemente ionizado como función de la temperatura. En segundo lugar, se analiza experimentalmente el comportamiento electromagnético de uno de los principales elementos constituyentes de la parte terminal de la cadena de radio: la antena. Finalmente, se presentan las perspectivas y conclusiones del trabajo. Las validaciones experimentales se realizan en la frecuencia de 2,4 GHz y con variaciones en temperatura desde 900 K hasta 1300 K. Experimentalmente se obtiene una atenuación del orden de 10-5 dB/m para 923 K, y una permitividad relativa compleja igual a 1+j10-12. Los resultados experimentales realizados a la antena, muestran que ésta se desadapta a medida que cambian las condiciones de temperatura: experimentalmente se obtuvo una variación de 78 kHz/K, para un delta de temperatura de 85 K.

Role of miR-222-3p in c-Src-Mediated Regulation of Osteoclastogenesis

Directory of Open Access Journals (Sweden)

Shinya Takigawa

2016-02-01

Full Text Available MicroRNAs (miRNAs are small non-coding RNAs that play a mostly post-transcriptional regulatory role in gene expression. Using RAW264.7 pre-osteoclast cells and genome-wide expression analysis, we identified a set of miRNAs that are involved in osteoclastogenesis. Based on in silico analysis, we specifically focused on miR-222-3p and evaluated its role in osteoclastogenesis. The results show that the inhibitor of miR-222-3p upregulated the mRNA levels of nuclear factor of activated T-cells, cytoplasmic 1 (NFATc1 and tartrate-resistant acid phosphatase (TRAP, while its mimicking agent downregulated their mRNA levels. Western blot analysis showed that its inhibitor increased the protein levels of TRAP and cathepsin K, while its mimicking agent decreased their levels. Genome-wide mRNA expression analysis in the presence and absence of receptor activator of nuclear factor κ-B ligand (RANKL predicted c-Src as a potential regulatory target of miR-222-3p. Live cell imaging using a fluorescence resonance energy transfer (FRET technique revealed that miR-222-3p acted as an inhibitor of c-Src activity, and a partial silencing of c-Src suppressed RANKL-induced expression of TRAP and cathepsin K, as well as the number of multi-nucleated osteoclasts and their pit formation. Collectively, the study herein demonstrates that miR-222-3p serves as an inhibitor of osteoclastogenesis and c-Src mediates its inhibition of cathepsin K and TRAP.

Coupled-analysis of current transport performance and thermal behaviour of conduction-cooled Bi-2223/Ag double-pancake coil for magnetic sail spacecraft

Energy Technology Data Exchange (ETDEWEB)

Nagasaki, Y., E-mail: nagasaki@rish.kyoto-u.ac.jp [Research Institute of Sustainable Humanosphere, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Nakamura, T. [Graduate School of Engineering, Kyoto University, Kyotodaigakukatsura, Nishikyo, Kyoto 615-8530 (Japan); Funaki, I. [Institute of Space and Astronautical Science, Japan Aerospace Exploration Agency, Sagamihara, Kanagawa 252-5210 (Japan); Ashida, Y.; Yamakawa, H. [Research Institute of Sustainable Humanosphere, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan)

2013-09-15

Highlights: • We model current transport and thermal performances of conduction-cooled HTS coil. • We investigate the effect of the longitudinal inhomogeneity of the HTS tape. • The analysis can precisely estimate performances of the conduction-cooled coil. • The longitudinal inhomogeneity of the HTS tape deteriorates coil performances. • Quench currents of the HTS coil are not consistent with the critical currents. -- Abstract: This paper investigated the quantitative current transport performance and thermal behaviour of a high temperature superconducting (HTS) coil, and the effect of the critical current inhomogeneity along the longitudinal direction of HTS tapes on the coil performances. We fabricated a double-pancake coil using a Bi-2223/Ag tape with a length of 200 m as a scale-down model for a magnetic sail spacecraft. We measured the current transport property and temperature rises during current applications of the HTS coil in a conduction-cooled system, and analytically reproduced the results on the basis of the percolation depinning model and three-dimensional heat balance equation. The percolation depinning model can describe the electric field versus current density of HTS tapes as a function of temperature and magnetic field vector, and we also introduced the longitudinal distribution of the local critical current of the HTS tape into this model. As a result, we can estimate the critical currents of the HTS coil within 10% error for a wide range of the operational temperatures from 45 to 80 K, and temperature rises on the coil during current applications. These results showed that our analysis and conduction-cooled system were successfully realized. The analysis also suggested that the critical current inhomogeneity along the length of the HTS tape deteriorated the current transport performance and thermal stability of the HTS coil. The present study contributes to the characterization of HTS coils and design of a coil system for the

Coupled-analysis of current transport performance and thermal behaviour of conduction-cooled Bi-2223/Ag double-pancake coil for magnetic sail spacecraft

International Nuclear Information System (INIS)

Nagasaki, Y.; Nakamura, T.; Funaki, I.; Ashida, Y.; Yamakawa, H.

2013-01-01

Highlights: • We model current transport and thermal performances of conduction-cooled HTS coil. • We investigate the effect of the longitudinal inhomogeneity of the HTS tape. • The analysis can precisely estimate performances of the conduction-cooled coil. • The longitudinal inhomogeneity of the HTS tape deteriorates coil performances. • Quench currents of the HTS coil are not consistent with the critical currents. -- Abstract: This paper investigated the quantitative current transport performance and thermal behaviour of a high temperature superconducting (HTS) coil, and the effect of the critical current inhomogeneity along the longitudinal direction of HTS tapes on the coil performances. We fabricated a double-pancake coil using a Bi-2223/Ag tape with a length of 200 m as a scale-down model for a magnetic sail spacecraft. We measured the current transport property and temperature rises during current applications of the HTS coil in a conduction-cooled system, and analytically reproduced the results on the basis of the percolation depinning model and three-dimensional heat balance equation. The percolation depinning model can describe the electric field versus current density of HTS tapes as a function of temperature and magnetic field vector, and we also introduced the longitudinal distribution of the local critical current of the HTS tape into this model. As a result, we can estimate the critical currents of the HTS coil within 10% error for a wide range of the operational temperatures from 45 to 80 K, and temperature rises on the coil during current applications. These results showed that our analysis and conduction-cooled system were successfully realized. The analysis also suggested that the critical current inhomogeneity along the length of the HTS tape deteriorated the current transport performance and thermal stability of the HTS coil. The present study contributes to the characterization of HTS coils and design of a coil system for the

Contribución al desarrollo de sensores de temperatura y redes de sensores en tecnología de fibra óptica

OpenAIRE

Madruga Saavedra, Francisco Javier

2006-01-01

Este trabajo de tesis recoge las contribuciones aportadas en el campo de los sensores de fibra óptica en tres ámbitos de trabajo. Un sistema sensor de alta temperatura sin contacto con transductores de fibras ópticas de sílice se ha presentado. Dos topologías de "ojo abierto" y "ojo cerrado" y un algoritmo de decodificación "pirometría de banda dual" propuesto en este trabajo son las novedosas aportaciones presentadas. El sistema ha sido validado en laboratorio y en pruebas de campo de forma ...

Contribución al desarrollo de sensores de temperatura y redes de sensores en tecnología de fibra óptica

OpenAIRE

Madruga Saavedra, Francisco Javier

2008-01-01

RESUMEN: Este trabajo de tesis recoge las contribuciones aportadas en el campo de los sensores de fibra óptica en tres ámbitos de trabajo. Un sistema sensor de alta temperatura sin contacto con transductores de fibras ópticas de sílice se ha presentado. Dos topologías de "ojo abierto" y "ojo cerrado" y un algoritmo de decodificación "pirometría de banda dual" propuesto en este trabajo son las novedosas aportaciones presentadas. El sistema ha sido validado en laboratorio y en pruebas de campo ...

Particle and powder characterisation of Bi-based superconductors

International Nuclear Information System (INIS)

Yavuz, M.; Guo, Y. C.; Liu, H. L.; Dou, S. X.; Vance, E. R.

1996-01-01

Full text: Superconductor precursor powder was ground in a planetary and an attrition mill using various combinations of grinding container, balls and carrier (dry and wet). Dry milling was found to be more effective than wet milling for reducing particle size irrespective of container and ball materials used in the planetary milling. On the other hand, wet milling was found more effective in the attrition milling. Serious Si contamination was observed in powders milled using agate grinding materials. Some C from polypropylene container was found after milling, but no Zr from YSZ balls. Effect of particle size on the property of Bi 2223/Ag tapes was investigated in terms of critical current density (J c ). Fine particle size was found to show high J c

Utilização das vitaminas C e E em rações para frangos de corte mantidos em ambiente de alta temperatura Use of vitamins C and E on ration for broilers kept in high temperature environment

Directory of Open Access Journals (Sweden)

Marcos Gonçalves de Souza

2011-10-01

Full Text Available O experimento foi realizado para avaliar os efeitos da suplementação das vitaminas C ou E na ração sobre o desempenho, as características de carcaça e os parâmetros hematológicos de frangos de corte mantidos em ambiente de alta temperatura. Foram utilizados 450 frangos de corte distribuídos em delineamento inteiramente ao acaso, com cinco tratamentos, cada um com nove repetições de 10 aves (período 1 a 21 dias ou de 7 aves (período de 22 a 42 dias por unidade experimental. Os tratamentos foram: ração basal (RB sem suplementação de vitaminas C e E; RB + 300 ppm de vitamina E; RB + 230 ppm de vitamina C; RB + 300 ppm de vitamina E + 230 ppm de vitamina C; e RB + 150 ppm de vitamina E + 115 ppm de vitamina C. Não houve efeito da suplementação das vitaminas C e E no desempenho zootécnico das aves na fase de 1 a 21 dias de idade. Na fase de 1 a 42 dias, a suplementação das vitaminas C e E influenciou somente a conversão alimentar. Os melhores resultados para os pesos absoluto e relativo de peito foram observados nas aves que receberam a ração basal suplementada com as combinações das vitaminas C e E. A concentração plasmática de triiodotironina, a porcentagem de células sanguíneas, a relação heterófilo/linfócito e os pesos absoluto e relativo do baço aos 21 e 42 dias de idade não foram influenciados pela suplementação vitamínica. A suplementação das vitaminas C e ou E não influi no desempenho zootécnico, no peso do baço e nos parâmetros sanguíneos de frangos de corte mantidos até 42 dias de idade em ambiente de alta temperatura. As combinações das vitaminas C e E promovem melhora nos pesos absoluto e relativo de peito de frangos de corte sob alta temperatura.This experiment was carried out to evaluate the effect of supplementation of vitamins C or E in the diet on performance, carcass characteristics and hematological parameters of broilers kept under high environmental temperature. Four hundred and

Strategic flat rolling of Ag/BSCCO-2223 tapes

DEFF Research Database (Denmark)

Nielsen, Morten Storgård; Bech, Jakob Ilsted; Eriksen, Morten

2002-01-01

In the process of single-step flat rolling of multifilament Ag/BSCCO-2223 wire to tape previous work has shown the optimum strategy giving maximum critical current density to be it balance between the length and width strain, so they are of equal size i.e. so, that the logarithmic strain ratio, L...

Specific features of acoustic properties of ceramic Bi1.4Pb0.6Ca2Sr2Cu3Oy

International Nuclear Information System (INIS)

Gajduk, A.L.; Fil', V.D.; Burma, N.G.

1991-01-01

Anomalies of sound velocity and attenuation, as well as of heat capacity are revealed in the Pb-stabilized Bi ceramics of the composition 2-2-2-3 atare 60 K, which are interpreted as the second-order phase transition. The sensitivity of the anomalies to the quenched magnetic flux is indicative of the magnetic nature of the transition. Similar features also observed at the same temperature in the 1-2-3* type superconducting systems

Structural and electronic properties of Pb-doped Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}: Comparison of LDA and GGA calculations

Energy Technology Data Exchange (ETDEWEB)

Camargo-Martínez, J.A., E-mail: jcamargo@unitropico.edu.co [Grupo de Investigación en Ciencias Básicas, Aplicación e Innovación - CIBAIN, Fundación Universitaria Internacional del Trópico Americano– Unitrópico, Yopal, Casanare (Colombia); Martínez-Pieschacón, D.J. [Departamento de Ciencias Básicas, Universidad Santo Tomás, Tunja, Boyaca (Colombia); Baquero, R. [Departamento de Física, CINVESTAV-IPN, Av. IPN 2508, 07360, México (Mexico)

2017-04-15

Highlights: • We present for the first time the effects of Pb doping on structural and electronic properties of Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10} (Bi2223) using GGA, compared with LDA results. • We found the Pb concentration for which the Bi–O pockets disappear from the Fermi Surface in the Bi2223 compound using GGA and LDA, respectively. - Abstract: We use Density Functional Theory to study the effects on the crystal structure and the electronic band structure of substituting Pb for Bi in Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10}. We further use the Local Density Approximation (LDA) and the Generalized Gradient Approximation (GGA). The Virtual Crystal Approximation (VCA) was used to account for the substitution. We found that GGA reproduces better the lattice parameters although in both cases the internal coordinates were reproduced with some uncertainties. We further looked at the behavior of the so called Bi–O pockets, some electronic states that originate on the Bi–O planes and that appear on the Fermi surface (FS) in contradiction to the experimental evidence. We found that LDA and GGA differ on that subject. With 26% Pb and using LDA, the Bi–O pockets run away from the FS. But when GGA is used, it is needed up to 35% Pb to make the Bi–O pockets disappear from the FS. In the last case, once the Bi–O pockets are removed from the FS, we get a very good agreement with angular resolved photo-emission (ARPES) and nuclear magnetic resonance (NMR) experiments.

Considerações sobre o conceito de temperatura e de temperatura absoluta

OpenAIRE

Leal Ferreira, G.F.

2006-01-01

Discute-se o conceito de temperatura que emerge da ação de contato, e a conveniência de torná-lo menos abstrato levando em conta a quantidade de matéria envolvida. Mostra-se que o conceito de 'energia térmica molar', numericamente igual ao produto da constante dos gases pela temperatura absoluta, preenche aquele fim, expressando o conteúdo cinético da energia molar, além de permitir desonerar a entropia de inadequada dimensionalidade. The concept of temperature acquired by means of our con...

Influence of preparation conditions on superconducting properties of ...

Indian Academy of Sciences (India)

cm2 at 20 K were ... We also investigated the effect of Li doping on Bi-2223 thin films. ... (Fujino et al 2001), co-evaporation (Cui et al 2001), ..... Effect of deposition rate (r) on Tc (a) and Jc at 20 K (b) of Bi-2223 thin films on STO substrate.

Balanço eletrolítico para suínos machos castrados em crescimento mantidos em ambiente de alta temperatura Electrolyte balance of growing males castrated swines in a high temperature environment

Directory of Open Access Journals (Sweden)

Anilce de Araujo Brêtas

2011-02-01

Full Text Available Avaliou-se o efeito do balanço eletrolítico (BE em rações com diferentes níveis de eletrólitos para suínos na fase de crescimento criados em alta temperatura. Foram utilizados 200 suínos machos castrados, com peso inicial de 25,3±1,3 kg e final de 68,8±3,4 kg, distribuídos em delineamento experimental inteiramente casualizado com cinco tratamentos e quatro repetições com dez animais por unidade experimental, para a fase de crescimento T1(testemunha ração sem suplementação de eletrólitos 191 mEq/kg; T2 (NaHCO3 ração suplementada bicarbonato de sódio (NaHCO3 250 mEq/kg; T3 (NaHCO3+KCl ração suplementada NaHCO3 e cloreto de potássio (KCl 250 mEq/kg; T4 (NaHCO3 ração suplementada NaHCO3 300 mEq/kg; e T5 (NaHCO3+KCl ração suplementada com NaHCO3 e KCl 300 mEq/kg. As variáveis avaliadas foram consumo de ração, ganho de peso, consumo de nitrogênio, consumo de lisina, eficiência de utilização de nitrogênio para ganho, eficiência de utilização de lisina para ganho, conversão alimentar e os parâmetros fisiológicos, frequência respiratória e temperatura retal. Foi coletado sangue para mensurar as concentrações sorológicas de Na, Cl e K. A temperatura média foi 29,65±3,80º C com UR do ar 69,6±10,4%, Temperatura do Globo Negro de 31,95±1,98º C e Índice de Temperatura do Globo Úmido em 80,51±2,44. Os níveis de BE reduziram (P0,05. A correção do BE não influenciou o desempenho dos suínos.The effect of electrolyte balance (EB in diets with different levels of electrolytes for growing swine under high environmental temperature was evaluated. Two hundred castrated pigs with initial weight of 25.3±1.3 kg and final weight of 68.8±3.4 kg were allotted in a completely randomized experimental design with five treatments and four replicates with 10 pigs per experimental unit, for the growing phase T1 (control diet without electrolyte 191 mEq/kg; T2 (NaHCO3 diet supplemented with sodium bicarbonate (NaHCO3

Características de la combustión con aire enriquecido con oxígeno y perspectivas de aplicación en PYME con procesos de alta temperatura

Directory of Open Access Journals (Sweden)

Juan Carlos González Palencia

2009-09-01

Full Text Available Las pequeñas y medianas empresas (PYME con procesos de alta temperatura, como la fundición y los tratamientos térmicos, son de gran importancia social y económica en los países en vía de desarrollo, siendo necesario aumentar su competitividad para garantizar su permanencia en el mercado. Dado que estas empresas son intensivas en el consumo de energía térmica, su competitividad se ve afectada por la obsolescencia y baja eficiencia de los sistemas de combustión, por lo que es necesaria la investigación y divulgación de nuevas tecnologías. Teniendo esto en mente, se presenta una revisión del estado del arte de la combustión con aire enriquecido con oxígeno (OEC, resaltando sus ventajas ambientales y productivas. Con el objetivo de mostrar su potencial se presenta un caso de aplicación a la fusión de latón en un horno autorregenerativo para el que se obtie- nen reducciones de consumo de combustible, tiempo de proceso y emisiones contaminantes de CO2 total equivalente del 28, 43 y 34% respectivamente y un incremento del 30% en la eficiencia al aumentar el contenido de O2 en el comburente de 21 a 35%. Sin embargo, el incremento del costo asociado al suministro de O2 representa un obstáculo para la penetración de esta tecnología.

Synthesis of the phase with T sub c =110 K in Bi(Pb)-Sr-Ca-Cu-O superconducting ceramics. Sintez fazy T sub c =110 K sverkhprovodyashchej keramiki sostava Bi(Pb)-Sr-Ca-Cu-O

Energy Technology Data Exchange (ETDEWEB)

Dubovitskij, A V; Makarov, E F; Makova, M K; Merzhanov, V A; Topnikov, V N [AN SSSR, Moscow (USSR). Inst. Khimicheskoj Fiziki

1991-05-01

Synthesis of 110 K single-phase bismuth ceramics (BiPb){sub 2}Sr{sub 2}Ca{sub n-1}Cu{sub n}O{sub x} was conducted in narrow temperature and time range. Diffusion of bismuth ions is proposed to be the decisive factor of synthesis of bismuth ceramics. The diffusion depends on prehistory of basic burden preparation and on its dispersivity and homogeneity in particluar. Optimal time of synthesis for lead doped ceramics of 2223 composition, synthesized from initial nitrate components, is equal to 65 h at 850 deg C. The role of Pb{sup 2+} ions is probably reduced to decrease of diffusion mobility of Bi{sup 3+} ions over the bismuth sublattice. Ceramics doping with CdO and CdCl{sub 2} compounds instead of lead stabilizes superconductivity in bismuth ceramics, but with worth superconducting parameters.

Magnetic properties of Aurivillius lanthanide-bismuth (LnFeO3nBi4Ti3O12 (n = 1,2 layered titanates

Directory of Open Access Journals (Sweden)

Tartaj, J.

2008-06-01

Full Text Available Bismuth titanates of Aurivillius layer-structure (BiFeO3nBi4Ti3O12, are of great technological interest because of their applications as non-volatile ferroelectric memories and high-temperature piezoelectric materials. The synthesis and crystallographic characterization of a new family of compounds (LnFeO3nBi4Ti3O12 was recently reported, in which the layers consist of LnFeO3 perovskites with a lanthanide Ln3+ substituting diamagnetic Bi3+. We report herein the magnetic properties of bulk samples, with Ln = Nd, Eu, Gd and Tb, and n = 1 and 2. Single-layer materials are paramagnetic, similar to non-substituted bismuth titanate Bi5FeTi3O15, and show crystal field effects due to the crystallographic environment of Eu3+ and Tb3+. Several anomalies are detected in the magnetization M(T of double-layer (LnFeO32Bi4Ti3O12 compounds, related to the strong magnetism of Tb and Gd, since they weakly appear for Nd and they are absent in the VanVleck Eu3+ ion and in the parent Bi6Fe2Ti3O18 compound.Los titanatos de hierro y bismuto con estructura laminar tipo Aurivillius, (BiFeO3nBi4Ti3O12, tienen un gran interés tecnológico debido a sus aplicaciones como memorias ferroeléctricas no volátiles y como piezoeléctrico cerámico de alta temperatura. La síntesis y la caracterización cristalina de una nueva familia de compuestos (LnFeO3nBi4Ti3O12 han sido recientemente reportadas, en la que el catión diamagnético Bi3+ ha sido sustituido por los paramagnéticos Ln3+ en los bloques de perovskita. Se estudian las propiedades magnéticas de muestras cerámicas en volumen con Ln = Nd, Eu, Gd y Tb, y n = 1 y 2. Los materiales con n=1 son paramagnéticos y similares al no sustituido Bi5FeTi3O15, y muestran efectos de campo cristalino debido al entorno cristalino de Eu3+ y Tb3+. Se han detectado algunas anomalías en la magnetización M(T de los compuestos n=2 (LnFeO32Bi4Ti3O12 que están relacionadas con el fuerte magnetismo de Tb y Gd, que aparecen d

Há equivalência entre a temperatura da membrana timpânica e a temperatura retal em ovinos Santa Inês normotérmicos?

OpenAIRE

Del Campo,Claudia; Boere,Vanner

2008-01-01

A utilização do termômetro de raios infravermelhos para a aferição da temperatura timpânica em animais tem se tornado uma alternativa prática na clínica veterinária. Em ovinos, a mensuração da temperatura timpânica não foi suficientemente comparada com a aferição da temperatura retal. Este estudo avaliou a equivalência entre a temperatura timpânica e a temperatura retal em 16 ovinos da raça Santa Inês. Durante a coleta de dados, a temperatura e a umidade relativa do ar foram monitoradas e não...

Informe de personal de apoyo: Álvarez Martini, Carlos Alberto (2016-2017)

OpenAIRE

Álvarez Martini, Carlos Alberto

2017-01-01

Proyectos de investigación en los cuales colabora: - Proyecto 11 G 133 UNLP- Metrología bi y tridimensional en el diseño, desarrollo y aplicación de concentradores ópticos solares para altas temperaturas. - Metrología en Salud Visual, “Análisis y Evaluación de Errores presentes en la utilización de Instrumentos Oftálmicos”. - Proyecto red CYTED de intercambio iberoamericano Integrado por España, Argentina, Brasil, Chile, Colombia y México, tiene como objetivo pri...

Highly oriented Bi-system bulk sample prepared by a decomposition-crystallization process

International Nuclear Information System (INIS)

Xi Zhengping; Zhou Lian; Ji Chunlin

1992-01-01

A decomposition-crystallization method, preparing highly oriented Bi-system bulk sample is reported. The effects of processing parameter, decomposition temperature, cooling rate and post-treatment condition on texture and superconductivity are investigated. The method has successfully prepared highly textured Bi-system bulk samples. High temperature annealing does not destroy the growing texture, but the cooling rate has some effect on texture and superconductivity. Annealing in N 2 /O 2 atmosphere can improve superconductivity of the textured sample. The study on the superconductivity of the Bi(Pb)-Sr-Ca-Cu-O bulk material has been reported in numerous papers. The research on J c concentrates on the tape containing the 2223 phase, with very few studies on the J c of bulk sample. The reason for the lack of studies is that the change of superconducting phases at high temperatures has not been known. The authors have reported that the 2212 phase incongruently melted at about 875 degrees C and proceeded to orient the c-axis perpendicular to the surface in the process of crystallization of the 2212 phase. Based on that result, a decomposition-crystallization method was proposed to prepare highly oriented Bi-system bulk sample. In this paper, the process is described in detail and the effects of processing parameters on texture and superconductivity are reported

El control difuso de temperatura de una incubadora

OpenAIRE

Avilés Cortez, Juan Carlos

2009-01-01

El objetivo del proyecto es el diseño de un circuito para el monitoreo y control difuso de temperatura de una incubadora, utilizando un microcontrolador, un sensor de temperatura digital y se realiza la administración a través de una PC. Como características principales son la utilización del microcontrolador, el sensor de temperatura digital STH-11 y lo más importante el Control Difuso Mandani de la Temperatura, se utilizó el protocolo de comunicación I2C entre el sensor y el microc...

Oxidación de Cu2O a CuO en Aire a Altas Temperaturas Oxidación de óxico cuproso a óxido cúprico en Aire a Altas Temperaturas

Directory of Open Access Journals (Sweden)

Torstein A. Utigard

2012-02-01

Full Text Available

Small Cu2O cylinders were oxidized in a TGA apparatus in air from 850 to 1000 ºC. The activation energy for the oxidation kinetics of the cuprous oxide in the temperature range mentioned above was alsoestimated. Cuprous oxide oxidizes according to the cubic law; such kinetic law is explained in terms of the defect concentration within the Cu2O crystal structure.

Materiales compuestos C/SiC para aplicaciones estructurales de alta temperatura. Parte I: estabilidad termodinámica y química

Directory of Open Access Journals (Sweden)

Aparicio, M.

2000-12-01

Full Text Available The development of aero-engine and aircraft industry is aimed to hypersonic technology, efficiency enhancements and pollutant emission reductions. This objective can only be reached by increasing the operating temperatures, utilising new materials which mechanical properties are retained up to high temperatures. SiC matrix composites reinforced with carbon fibres (C/SiC are good examples with very good bending and thermal shock resistance at temperatures up to 1600ºC as well as low density. However, the fact which currently inhibits the application of these materials is the high oxidation rate of carbon fibres at temperatures above 450ºC. In the first part of the paper, a review of the most important properties and oxidation mechanisms of C and SiC has been carried out. The influence of each material disposition, individually and as composite, has been analysed.

El desarrollo de la industria aeroespacial se orienta actualmente hacia la tecnología hipersónica, el incremento en el rendimiento de las reacciones de combustión y la reducción de la emisión de contaminantes. Estos objetivos sólo pueden alcanzarse aumentando la temperatura de combustión, para lo cual es necesario desarrollar nuevos materiales que conserven sus propiedades mecánicas hasta temperaturas muy elevadas. Entre ellos se encuentran los materiales compuestos de matriz de SiC reforzada con fibra continua de carbono (C/SiC, cuyas propiedades más importantes son una elevada resistencia a flexión y al choque térmico desde temperatura ambiente hasta 1600ºCy su reducido peso específico. Sin embargo, el principal problema que acompaña a los materiales compuestos C/SiC es la elevada velocidad de oxidación de la fibra de carbono a partir de 450ºC. En la primera parte del trabajo se realiza una revisión de las características más relevantes del carbono y SiC, y de su comportamiento frente a la oxidación, tanto por separado como formando parte de materiales

Heating rate effect on the evolution of texture in (Bi,Pb)₂Sr₂Ca₂Cu₃O₁₀ Ag-sheathed tapes

DEFF Research Database (Denmark)

Grivel, J.C.; Raittila, J.; Xu, G.J.

2005-01-01

Bi2223/Ag tapes have been produced by the powder-in-tube technique. The evolution of texture during the first heat treatment has been studied by means of in situ synchrotron radiation diffraction. Using various heating rates (1, 2 and 4 degrees C min(-1)), it wag found that the kinetics of prefer...

Temperature dependence of filament-coupling in Bi-2223 tapes: magneto-optical study

International Nuclear Information System (INIS)

Bobyl, A.V.; Shantsev, D.V.; Galperin, Y.M.; Johansen, T.H.; Baziljevich, M.; Gaevski, M.E.

2000-01-01

Coupling through random superconducting bridges between filaments in a multifilamentary Ag-sheathed Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ tape has been investigated by magneto-optical imaging at temperatures from 20 K up to T c . Magnetic flux distributions have been measured on the surface of an intact tape in the remanent state on applying a strong perpendicular magnetic field. The flux distributions observed at low temperatures reflect the arrangement of individual filaments. At high temperatures, the distribution becomes more similar to that for a uniform monocore tape, indicating that superconducting connections appear between the filaments. To discuss the relative contributions of the intra- and inter-filament currents, a simple model based on the Bean critical state was proposed and applied to analyse the temperature dependent behaviour. The inter-filament coupling, increasing with temperature, reaches at 77 K a point where the currents flowing in large inter-filament loops are roughly equal to the intra-filament currents. (author)

Estudio experimental de la conducción del calor en el maquinado de materiales endurecidos con altas velocidades de corte. // Experimental study of heat conduction in mechanization with high cutting speeds of hardened materials.

Directory of Open Access Journals (Sweden)

L. Cardoso Brandão

2006-01-01

Full Text Available El trabajo trata del estudio teórico-experimental de la conducción del calor en los materiales endurecidos, usados para laproducción de moldes y matrices, al maquinarlos con altas-velocidades del corte. Los materiales utilizados son los acerosAISI P20 y AISI D2. Los ensayos se realizaron con fresas de punta esférica (Ball Nose con revestimiento (TiAlN y lasprobetas para los ensayos tienen la forma de una ¼ parte de un tubo de 28 mm de diámetro con una longitud de 100 mm.Las pruebas realizadas demuestran la variación de la temperatura en función de los diferentes sistemas de refrigeración. Seutilizo aire comprimido y aire comprimido frío, comparándose las temperaturas de las probetas con el sistema sinrefrigeración de ningún tipo. Fueron también evaluadas las deformaciones sufridas por la superficie maquinada, debido alas variaciones de temperatura teniendo en cuenta la influencia de los sistemas de refrigeración empleados.Palabras claves: Temperatura; conducción del calor; alta velocidad de corte, moldes y matrices._________________________________________________________________________Abstract.This paper deals with the theoretical-experimental study of heat conduction in hardened materials for the production ofmolds and dies using high speed cutting. The employed materials were the AISI P20 and AISI D2 steels, being the testscarried out with (TiAlN coated ball nose in a work piece with the shape of a 1/4 tube with 28 mm diameter and 100 mmlength. This investigation demonstrates the variation of temperature as a function of different cooling systems, that is,compressed air and compressed cold air. Possible geometric deformation of the machined surfaces due to these variationsin temperature for distinct cooling systems was also evaluated.Keywords: Temperature, heat exchange; high cutting speed, dies.

Rapid formation of the 110 K phase in Bi-Pb-Sr-Ca-Cu-O through freeze-drying powder processing

International Nuclear Information System (INIS)

Song, K.H.; Liu, H.K.; Dou, S.X.; Sorrell, C.C.

1990-01-01

This paper reports three techniques for processing Bi-Pb-Sr-Ca-Cu-O (BPSCCO) powders investigated: dry-mixing, sol-gel formation, and freeze-drying. It was found that sintering for 120 h at 850 degrees C is required to form nearly single-phase (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O 10-y by dry-mixing, whereas sintering for 30 h at 840 degrees C was sufficient to form the 110 K (2223) phase when freeze-drying was used. The sol-gel route was found to be intermediate in efficiency between these two techniques. Freeze-drying provided highly reactive, intimately mixed, and carbon-free precursors. The presence of carbonates in the uncalcined powders was the major cause of phase segregation and sluggishness of the 110 K phase formation

Senor monolitico de temperatura compativel com microprocessador

OpenAIRE

Pedro Cuervo Diaz

1992-01-01

Resumo: Este trabalho descreve um sensor de temperatura com saída compatível com microprocessadores em uma ampla faixa de temperaturas, sem necessidade de outro componente externo. Sua saída em frequência proporcional à temperatura, pode-se obter em dois níveis de corrente ou dois níveis de tensão, permitindo sua montagem em umencapsulamento com três terminais. No Capítulo1, com o objetivo de posicionar o trabalho no universo dos sensores. ocircuito integrado projetado, são apresentados trê...

Positron annihilation study of the high-T{sub c} (Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} superconductor

Energy Technology Data Exchange (ETDEWEB)

Lim, H.J. [Utah Univ., Salt Lake City, UT (United States). Dept. of Metallurgical Engineering; Byrne, J.G. [Utah Univ., Salt Lake City, UT (United States). Dept. of Metallurgical Engineering

1997-03-01

Positron lifetime spectroscopy (PLS) and positron Doppler-broadening spectroscopy (PDBS) were applied to the high-T{sub c} lead-doped Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} (BPSCCO 2223) superconductor as a function of temperature. Neither positron lifetimes nor Doppler parameters (S, W, and S/W) showed significant change through T{sub c}. This may result from having the highest positron density in the open BiO{sub 2} double layers and no significant positron density in the superconducting CuO{sub 2} layers where positrons, if mainly present, are known to be sensitive to the transition in other high-T{sub c} superconductors. Doppler parameters showed that the probability of positron annihilations with core electrons in the lattice slightly increased and that the probability of positron annihilations with conduction electrons slightly decreased as temperature decreased from ambient temperature to 20 K. The lifetime associated with positron annihilations in the perfect lattice of the sample ({tau}{sub 1}) was 209 ps and, due to the annihilations at internal surfaces or voids in the sample ({tau}{sub 2}) was about 540 ps, independent of temperature. Finally, the mean lifetime for BSCCO 2223 was about 307 ps. (orig.).

FRONTIER FIELDS CLUSTERS: DEEP CHANDRA OBSERVATIONS OF THE COMPLEX MERGER MACS J1149.6+2223

Energy Technology Data Exchange (ETDEWEB)

Ogrean, G. A.; Weeren, R. J. van; Jones, C.; Forman, W.; Andrade-Santos, F.; Murray, S. S.; Nulsen, P.; Bulbul, E.; Kraft, R.; Randall, S. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Dawson, W. A. [Lawrence Livermore National Lab, 7000 East Avenue, Livermore, CA 94550 (United States); Golovich, N. [University of California, One Shields Avenue, Davis, CA 95616 (United States); Roediger, E. [Astronomy and Astrophysics Section, Dublin Institute for Advanced Studies, 31 Fitzwilliam Place, Dublin 2 (Ireland); Zitrin, A.; Sayers, J. [Cahill Center for Astronomy and Astrophysics, California Institute of Technology, MC 249-17, Pasadena, CA 91125 (United States); Goulding, A. [Department of Astrophysical Sciences, Princeton University, Princeton, NJ 08544 (United States); Umetsu, K. [Institute of Astronomy and Astrophysics, Academia Sinica, P.O. Box 23-141, Taipei 10617, Taiwan (China); Mroczkowski, T. [U.S. Naval Research Laboratory, 4555 Overlook Avenue SW, Washington, DC 20375 (United States); Bonafede, A. [Hamburger Sternwarte, Universität Hamburg, Gojenbergsweg 112, D-21029 Hamburg (Germany); Churazov, E., E-mail: gogrean@cfa.harvard.edu [Max Planck Institute for Astrophysics, Karl-Schwarzschild-Str. 1, D-85741, Garching (Germany); and others

2016-03-10

The Hubble Space Telescope Frontier Fields cluster MACS J1149.6+2223 is one of the most complex merging clusters, believed to consist of four dark matter halos. We present results from deep (365 ks) Chandra observations of the cluster, which reveal the most distant cold front (z  =  0.544) discovered to date. In the cluster outskirts, we also detect hints of a surface brightness edge that could be the bow shock preceding the cold front. The substructure analysis of the cluster identified several components with large relative radial velocities, thus indicating that at least some collisions occur almost along the line of sight. The inclination of the mergers with respect to the plane of the sky poses significant observational challenges at X-ray wavelengths. MACS J1149.6+2223 possibly hosts a steep-spectrum radio halo. If the steepness of the radio halo is confirmed, then the radio spectrum, combined with the relatively regular ICM morphology, could indicate that MACS J1149.6+2223 is an old merging cluster.

TransAlta: More than a utility

International Nuclear Information System (INIS)

Mikalson, D.A.

1991-01-01

TransAlta Utilities Corporation is Canada's largest privately owned utility and is also a major coal mining company. In 1989, TransAlta produced 20.9% of all coal mined in Canada. A brief history of TransAlta is presented along with TransAlta's present coal operations and plans for the next three years. An overview is presented of how TransAlta Fuel Supply is organized to utilize contracted mining operation, engineering and environmental services and in-house capabilities. Recent strategic initiatives to improve organizational efficiency and the mining operations are discussed. These range from developing a common departmental vision to modifying major mining equipment. TransAlta's proactive role in clean coal combustion such as low NOx-SOx burner, integrated combined cycle gasification, and other energy research projects is reviewed. A summary is provided of recent participation of TransAlta in environmental management initiatives. Recent successes of TransAlta's unregulated subsidiary in the development of cogeneration facilities and the future of this area of business are discussed. 8 refs., 4 figs

Effect of impregnation of ZrO2 on the chemical stability and the superconductivity of Y- and Bi-systems

International Nuclear Information System (INIS)

Muroya, Masaaki; Minamiyama, Hideaki

1994-01-01

The results are given concerning the influence of impregnation of Zr on chemical stability and superconductivity of YBa 2 (Cu 1-x · Zr x ) 3 O 7-y (123-system) and Bi 1.84 Zr x Pb 0.34 Sr 1.91 Ca 2.03 Cu 3.06 O y (2223-system) superconductors, when the samples are contacted with the solutions of acid (pH3), distilled water (pH5.6) and base (pH9), where x = 0-0.35. It is concluded that the low chemical stability was found in the case of YBZCO, barium hydroxide and/or barium carbonate were precipitated into the solutions, even though mechanical strength was increased by impregnation of Zr, and the chemical stability of Bi-system is high compared with that of the Y-system. 8 refs., 5 figs

Thermodynamic study of the rich-Bi2O3 region of the Bi2O3-ZnO system

Directory of Open Access Journals (Sweden)

de la Rubia, M. A.

2006-06-01

Full Text Available Precise knowledge of the Bi2O3-ZnO system is fundamental to control the functional microstructure of ZnO-based varistors. Also the potential applications of materials based on ZnO and Bi2O3 as dielectric materials in the high frequency range have renewed the interest in this binary system. The aim of the present work is to carry out a thermodynamic analysis of the Bi2O3-ZnO phase diagram, taking into account the existing experimental information. Thermodynamic calculation has been performed according CALPHAD methodology (CALculation of PHAse Diagrams, using the software Thermo-Calc.El conocimiento preciso del sistema Bi2O3-ZnO es una herramienta básica para conseguir el control de la microestructura de los varistores basados en ZnO. Recientemente otros materiales basados en óxidos de cinc y bismuto han mostrado un gran potencial para su uso en aplicaciones como dieléctricos a frecuencias altas, renovando el interés por dicho sistema binario. El objetivo del presente trabajo es realizar una evaluación termodinámica del diagrama de fases consistente para el sistema Bi2O3-ZnO teniendo en cuenta la información experimental existente del mismo. La evaluación termodinámica del sistema se ha llevado a cabo mediante la metodología CALPHAD (CALculation of PHAse Diagrams, empleando el software Thermo- Calc.

Mild temperatures on bud breaking dormancy in peaches Temperaturas amenas na superação da dormência de pessegueiros

Directory of Open Access Journals (Sweden)

Geraldo Chavarria

2009-10-01

Full Text Available The search for low chill cultivars for peach production in areas with low chill accumulation (temperatures below 7.2°C has stimulated studies about the higher temperatures effects on low chill cultivars. The objective of this research was to evaluate the influence of mild temperatures on flowering and leafing of 'Turmalina' and 'Ágata' cultivars with low and medium low chilling requirements, respectively. Plants obtained by grafting flower twigs in the autumn, after the grafting, were submitted to chilling treatments (150, 250, 350, 500 and 672 hours at three temperature levels (5°C, 10°C and 15°C. After the end of the treatments, the plants had been taken to greenhouse (20°C±5°C and evaluated weekly. The results showed that satisfactory flower and leaf development occur even at temperatures as high as 15°C for a period of 150 hours, in 'Turmalina' peach. Temperatures of 10°C for a period equal or superior to 350 hours promote satisfactory leafing in 'Ágata' peach. Temperatures of 10°C and 15°C cause earlier development of flowers and leaves in both cultivars when compared to 5°C.A busca por cultivares pessegueiro com baixa necessidade em frio para regiões com pouco acúmulo de frio (temperaturas abaixo de 7,2°C tem estimulado estudos sobre o efeito de altas temperaturas sobre cultivares de baixa necessidade de frio. O objetivo desta pesquisa foi avaliar a influência de temperaturas amenas na floração e brotação da 'Turmalina' e 'Ágata', duas cultivares com baixa e média necessidade de frio, respectivamente. Plantas obtidas por enxertia no outono foram submetidas a tratamentos de frio (150, 250, 350, 500 e 672 horas em três níveis de temperatura (5°C, 10°C e 15°C. Após os tratamentos, estas plantas foram colocadas em casa de vegetação a temperatura de 20°C±5°C e avaliadas semanalmente. Conclui-se que temperatura de até 15°C por um período de 150 horas é capaz de resultar em floração e brotação satisfat

A Influência da Prensagem a Quente nas Propriedades dos Painéis de Fibras de Alta Densidade, Aquando do seu Revestimento por Películas

Directory of Open Access Journals (Sweden)

Idalina Domingos

2016-07-01

Full Text Available Um conjunto de painéis de fibras de alta densidade, colados com uma resina de melamina/ureia-formaldeído, foi submetido a operações de prensagem a quente, de modo a estudar a influência desta operação nas propriedades do substrato. Usou-se uma prensa de pratos, a uma pressão que permitisse um contacto firme entre os painéis e os pratos da prensa. Foi desenvolvido um plano experimental para três temperaturas diferentes de 95, 180 e 210 º C e dois tempos de prensagem, de 22 e 35 segundos, para cada uma delas. Os painéis foram fabricados com fibras de pinho (Pinus pinaster a uma densidade média de 930 kg/m3 e espessura média de 6,7 mm. De acordo com os resultados obtidos, as operações de pós-fabrico dos painéis de alta densidade resultaram numa ligeira melhoria do módulo de elasticidade, da tensão de rotura à flexão estática e da resistência interna dos painéis usados como substrato. Observou-se também uma ligeira diminuição da humidade de equilíbrio e espessura dos painéis, bem como um aumento da densidade e do inchamento, com o aumento da temperatura e tempo de prensagem.

Production of BiPbSrCaCuO thin films on MgO and Ag/MgO substrates by electron beam deposition techniques

CERN Document Server

Varilci, A; Gorur, O; Celebi, S; Karaca, I

2002-01-01

Superconducting BiPbSrCaCuO thin films were prepared on MgO(001) and Ag/MgO substrates using an electron beam (e-beam) evaporation technique. The effects of annealing temperature and Ag diffusion on the crystalline structure and some superconducting properties, respectively, were investigated by X-ray diffraction, atomic force microscopy, and by measurements of the critical temperature and the critical current density. It was shown that an annealing of both types of films at 845 or 860 C resulted in the formation of mixed Bi-2223 and Bi-2212 phases with a high degree of preferential orientation with the c-axis perpendicular to the substrates. The slight increase of the critical temperature from 103 K to 105 K, the enhancement of the critical current density from 2 x 10 sup 3 to 6 x 10 sup 4 A/cm sup 2 , and the improved surface smoothness are due to a possible silver doping from the substrate. (Abstract Copyright [2002], Wiley Periodicals, Inc.)

Níveis de energia metabolizável em rações para frangos de corte mantidos em ambiente de alta temperatura Metabolizable energy levels in diets for broiler maintained in environment of high temperature

Directory of Open Access Journals (Sweden)

Firmino José Vieira Barbosa

2008-05-01

Full Text Available Quatrocentas aves com peso médio de 675,00 g foram distribuídas em delineamento de blocos casualizados, com base no peso das aves, com cinco tratamentos e quatro repetições. As dietas experimentais foram constituídas de cinco níveis de energia metabolizável (2.800, 2.900, 3.000, 3.100 e 3.200 kcal de EM/kg de ração formuladas para atender às exigências nutricionais, exceto de energia metabolizável. O aumento do nível de energia das rações foi obtido pela adição de óleo de soja. Realizaram-se análises de variância e de regressão, associando-se os níveis de energia aos valores das variáveis estudadas. As aves foram avaliadas quanto ao desempenho (consumo de ração, ganho de peso e conversão alimentar e às características de carcaça nos períodos de 22 a 35 dias, 36 a 42 dias, 43 aos 49 dias e de 22 a 49 dias de idade. O ganho de peso e a conversão alimentar de frangos de corte da linhagem Hubbard mantidos em ambiente de alta temperatura não são influenciados pelos níveis de energia metabolizável da ração. Os níveis de energia da dieta não afetam os rendimentos de carcaça, coxa, sobrecoxa, asa, tulipa, moela coração fígado, proventrículo e intestino. Entretanto, a gordura abdominal aumenta e o rendimento de peito decresce proporcionalmente à elevação da energia da dieta em ambiente de altas temperaturas.Four hundred birds Hubbard linage with average weight of 675g were distributed to completely randomized block design, based in birds he weight, with five treatments and four replications. The experimental diets were constituted of five metabolizable energy levels (2,800, 2,900, 3,000, 3,100 and 3,200 kcal of ME/kg ration formulated to attend the nutritional requirements, except for metabolizable energy. The increase of energy was obtained by the addition of soybean oil. The variance and regression analysis was made, associating the energy levels with the values of the studied characteristics. The birds

Superconducting thin films of Bi-Sr-Ca-Cu-O by laser ablation

Science.gov (United States)

Bedekar, M. M.; Safari, A.; Wilber, W.

1992-11-01

Superconducting thin films of Bi-Sr-Ca-Cu-O have been deposited by KrF excimer laser ablation. The best in situ films showed a Tc onset of 110 K and a Tc(0) of 76 K. A study of the laser plume revealed the presence of two distinct regimes. The forward directed component increased with fluence and the film composition was stoichiometric in this region. This is in agreement with the results on the 123 system by Venkatesan et al. [1]. The film properties were found to be critically dependent on the substrate temperature and temperatures close to melting gave rise to 2212 and 2223 phases. At lower temperatures, 2201 and amorphous phases were obtained. The film morphology and superconducting properties were a function of the target to substrate distance and the oxygen pressure during deposition and cooling. An increase in the target to substrate distance led to a deterioration of the properties due to the energy consideration for the formation of 2212 and 2223 phases. The best films were obtained using cooling pressures of 700 Torr. The microwave surface resistance of the films measured at 35 GHz dropped below that of copper at 30 K. Film growth was studied using X-ray diffraction and STM/AFM. This work is a discussion of the role of the different variables on the film properties.

Stability analysis of high temperature superconducting coil in liquid hydrogen

International Nuclear Information System (INIS)

Nakayama, T.; Yagai, T.; Tsuda, M.; Hamajima, T.

2007-01-01

Recently, it is expected that hydrogen plays an important role in energy source including electric power in near future. Liquid hydrogen has high potential for cooling down superconducting coil wound with high temperature superconductors (HTS), such as BSCCO, YBCO. In this paper, we study stabilities of the coils wound with BSCCO tapes, which are immersed in the liquid hydrogen, and compare stability results with those cooled by liquid helium. We treat a minimum propagation zone (MPZ) theory to evaluate the coil stability considering boiling heat flux of the liquid hydrogen, and specific heat, heat conduction and resistivity of HTS materials as a function of temperature. It is found that the coil cooled by the liquid hydrogen has higher stability margin than that cooled by the liquid helium. We compare the stability margins of both coils wound with Bi-2223/Ag tape and Bi-2212/Ag tape in liquid hydrogen. As a result, it is found that the stability of Bi-2212 coil is equivalent to that of Bi-2223 coil in low and high magnetic field, while the maximum current of Bi-2212 coil exceeds a little bit that of Bi-2223 coil in both magnetic fields

Duração da suplementação de ractopamina em dietas para leitoas em terminação mantidas sob alta temperatura ambiente Duration of ractopamine supplementation in diets for finishing gilts maintained under high temperature environment

Directory of Open Access Journals (Sweden)

Elizangela Alves da Silva

2011-02-01

Full Text Available Este estudo foi realizado com o objetivo de avaliar a duração da suplementação de ractopamina na dieta de leitoas em terminação, mantidas sob alta temperatura ambiente. Foram utilizadas 48 leitoas com peso inicial de 70,4±2,6kg, distribuídas no delineamento de blocos ao acaso, com seis tratamentos (suplementação de ractopamina por 0, 7, 14, 21, 28 e 35 dias pré-abate e quatro repetições, sendo a unidade experimental constituída por dois animais. O peso final e o consumo de ração diário não foram influenciados (P>0,05 pelos tratamentos. O ganho de peso aumentou e a conversão alimentar reduziu linearmente (P0,05 pela duração da suplementação de ractopamina na dieta. O peso dos pulmões, coração, fígado, rins e baço também não foi modificado (P>0,05 pelos tratamentos. Concluiu-se que a inclusão de 20ppm de ractopamina na dieta de leitoas em terminação, mantidas sob alta temperatura ambiente, durante 28 dias, maximiza a resposta de ganho de peso diário e, durante 35 dias, maximiza a resposta para conversão alimentar. Contudo, a inclusão do aditivo não altera as características quantitativas de carcaça e não afeta o desenvolvimento das vísceras.The study was conducted to evaluate the duration of the supplementation of ractopamine in the diet of finishing gilts maintained under high temperature environment. Forty eight females, with initial weight of 70.4±2.6kg were used. The pigs were distributed in randomized blocks design of six treatments (supplementation of ractopamine for 0, 7, 14, 21, 28 and 35 days pre-slaughter and four replications, each experimental unit consisted of two animals. The final weight and daily feed intake were not affected (P>0.05 by treatments. The weight gain increased and the feed conversion decreased linearly (P0.05 by duration of supplementation of ractopamine in the diet. The weights of the lungs, heart, liver, kidneys and spleen were not modified (P>0.05 by treatments. It was

INFLUÊNCIA DE DISTINTOS SISTEMAS ATMOSFÉRICOS NA TEMPERATURA DE SUPERFÍCIE DO MUNICÍPIO DE VITÓRIA (ES

Directory of Open Access Journals (Sweden)

Wesley de Souza Campos Correa

2015-03-01

Full Text Available O presente estudo teve por objetivo investigar a relação entre as mudanças de temperatura de superfície e usos e coberturas da terra do município de Vitória no estado do Espírito Santo, sob condições atmosféricas distintas, por meio de produtos orbitais, sub-orbitais, técnicas de sensoriamento remoto em ambiente SIG. Com a utilização do sensor infravermelho termal foi possível verificar que à aproximação da frente fria com vento predominante sul foi preponderante para minimização das ilhas de calor, e que durante a atuação da Alta Subtropical do Atlântico Sul (ASAS estes fenômenos são mais intensos, evidenciando que os tipos de tempo são os principais fatores controladores da intensidade desse fenômeno. Os resultados extraídos durante a passagem do satélite evidenciaram áreas no município de Vitória com intensa emitância termal como áreas construídas, pavimentadas, telhados e outras superfícies típicas da paisagem urbana, bem como a distribuição heterogênea dessas respostas, resultando em temperaturas elevadas, sobretudo no dia 30 de julho de 2011. O estudo demostrou também que a utilização dessa técnica pode contribuir na perspectiva do planejamento urbano, na medida em que são definidos padrões na distribuição da temperatura da superfície de acordo com o uso e cobertura da terra.

Tratabilidade do lodo biológico têxtil e produção de biogás em reator UASB em diferentes temperaturas

Directory of Open Access Journals (Sweden)

Júnia Schultz

Full Text Available RESUMO Neste trabalho avaliou-se o comportamento de um reator UASB em escala laboratorial (16 L no tratamento de lodo biológico têxtil com produção de biogás, operando em diferentes temperaturas, 35 (mesofílica, 45 e 55ºC (termofílica, com tempo de detenção hidráulica (TDH constante de 24 h. O reator UASB apresentou-se apto a tratar o lodo têxtil, sendo influenciado positivamente pelo incremento da temperatura, mostrando maiores remoções nas temperaturas termofílicas e com altas taxas de remoção de todos os parâmetros físico-químicos monitorados: demanda química de oxigênio (DQO (97% em 45 e 55ºC, demanda bioquímica de oxigênio (DBO (95% em 45ºC e 94% em 55ºC, fósforo total (P-total (95% a 45 e 55ºC e nitrogênio total (N-total (94% a 45 e 55ºC. Quanto à produção de biogás e à concentração de metano, os maiores valores foram observados a 45ºC. Com base nos resultados alcançados, confirmam-se a tratabilidade do lodo têxtil e a produção de biogás em UASB, com melhor performance a 45ºC.

Estonia's Alta buys Lauma lingerie

Index Scriptorium Estoniae

2004-01-01

Eesti investeeringute firma Alta Capital ostis 76,4 protsenti pesutootja Lauma aktsiatest. Tulevikus plaanitakse suunduda Ida- ja Lääne-Euroopa turgudele. Alta Capital omab 79 protsenti Klementi aktsiatest

Temperature- and field-dependent critical currents in [(Bi,Pb)2Sr2Ca2Cu3Ox]0.07(La0.7Sr0.3MnO3)0.03 thick films grown on LaAlO3 substrates

Science.gov (United States)

Paredes, Omar; Morán, Oswaldo; Baca, Eval

2013-01-01

La0.7Sr0.3MnO3 (LSMO) nanoparticles were embedded in (Bi,Pb)2Sr2Ca2Cu3Ox (Bi2223) thick films, which were grown by simple melting-quenching-annealing (MQA) method on (001)-oriented LaAlO3 (LAO) substrates. The nominal composition of the composite-like hybrid system was (Bi2223)1-x(LSMO)x with x = 0.03. The constituent elements, Bi2223 and LSMO, were prepared separately by standard solid state reaction and Pechini's method, respectively. The analysis of the X-ray diffraction patterns suggested a polycrystalline growth mode of the thick films on the LAO substrates. From electric transport measurements, the superconducting onset temperature and the superconducting critical temperature (ρ = 0) ended up being 105 and 62 K, respectively. The flux pinning energy U was determined using the Anderson-Kim model. The value of U was compared with those obtained for similar samples with concentrations x = 0.01 and x = 0.05. Current-voltage characteristics were recorded at different temperatures in order to analyze the behavior of the superconducting current (Ic) of the films. A dramatic drop of Ic was observed at ˜20 K. This seems to be linked to the presence of flux creep acting as dissipation factors attributed to LSMO nanoparticles. Isothermal magnetization loops recorded at T Tc showed clear diamagnetic and ferromagnetic signals, which verify the multifunctional character of the system. Based on the isothermal M(H)-loops recorded at 5, 20, and 40 K and taking Kim's model into account, the dependence of superconducting current density (Jc), and the volume pinning force (Fp) on the magnetic field were calculated. The dependence Jc(B) at 5 K showed an exponential-type behavior, which is described by an empirical equation. This empirical equation considers the maximum value of Fp, which may be scaled with the Kramer's expression for Fp. From this scaling procedure, diverse exponents, associated with different pinning mechanisms, were determined. The drastic fall of Jc(B) at T

Cultivo de cachama blanca en altas densidades y en dos sistemas cerrados

Directory of Open Access Journals (Sweden)

Germán Poleo

2011-04-01

Full Text Available El objetivo de este trabajo fue evaluar la tolerancia de la cachama blanca, Piaractus brachypomus, a cultivos en altas densidades en sistemas cerrados. Novecientos alevines de 44,3±26 g de peso, se distribuyeron en seis tanques de concreto, con 4,8 m³ de agua. Tres tanques presentaron cero recambio de agua (SCR, y en otros tres, el agua se hizo circular a través de un bioclarificador (SRA. Ambos tratamientos presentaron fuerte aireación para mantener los sólidos en suspensión y suministrar aire. Los peces se alimentaron a saciedad con pienso comercial por 192 días. Los parámetros de calidad de agua como: oxígeno disuelto, amonio total, nitritos, nitratos, alcalinidad, dureza, temperatura y pH, se midieron semanalmente. Los peces en el SCR crecieron a una tasa de 2,34±0,05 g por día, y tuvieron conversión alimenticia de 1,5±0,06, densidad final de 12,96±0,53 kg m-3, y peso final de 449,5±99 g. En el SRA, los peces crecieron 2,33±0,03 g por día, con conversión alimenticia de 1,6±0,07, densidad final de 12,13±1,12 kg m-3, y peso final de 446,5±10 g. La cachama blanca puede ser cultivada en sistemas cerrados con cero recambio de agua en altas densidades.

Monitorización de deformaciones y temperaturas en la estructura de un túnel artificial de alta velocidad mediante sensores ópticos puntuales, de longitud y distribuidos

Directory of Open Access Journals (Sweden)

Torres, B.

2015-06-01

Full Text Available Structural Health Monitoring (SHM is presently having a great development. Strains and temperatures are usually the key parameters to be monitored due to their relevance when explaining structural behavior. Several types of sensors are used in SHM, but fiber optic sensors are especially interesting due to their advantages with respect to conventional sensors. In this paper, the monitoring of a high-speed train tunnel recently built in Spain using three types of fiber optic sensors developed by the authors is shown. Results given by the sensors are compared to those provided by a theoretical model built using FEM. Comparison of measurements and theoretical results confirms that the sensors reproduced remarkably well the general patterns of the tunnel structural behavior, even when strains are relatively small (around 5 με. Finally, the paper discusses the behavior of the sensors, their measurements and their field of application which is useful for researchers and practitioners.La monitorización de estructuras es una rama de la ingeniería estructural que está captando mucha atención actualmente. Las deformaciones y temperaturas son, habitualmente, los parámetros monitorizados porque son los que mejor representan el comportamiento estructural. De todos los tipos de sensores existentes, los basados en fibra óptica resultan especialmente interesantes debido a sus ventajas comparativas sobre los sensores convencionales. En este artículo se presentan los trabajos de monitorización de la estructura de un túnel artificial de Alta Velocidad construido en Mogente (España mediante tres tipos de sensores ópticos desarrollados por los autores. Los resultados de los sensores se comparan con los proporcionados por un modelo teórico de elementos finitos. Esta comparación confirma que los sensores reproducen notablemente bien la pauta general de comportamiento de la estructura, incluso con pequeños niveles de deformación (5με. Por último, el

Phase stability, oxygen nonstoichiometry, and superconductivity properties of Bi2Sr2CaCu2O8+δ and Bi1.8Pb0.4Sr2Ca2Cu3O10+δ

International Nuclear Information System (INIS)

Mozhaev, A.P.; Chernyaev, S.V.; Badun, Y.V.

1995-01-01

Phase stability of Bi 2 Sr 2 CaCu 2 O 8+δ (2212) and Bi 1.8 Pb 0.4 Sr 2 Ca 2 Cu 3 O 10+δ (2223) was studied by means of thermogravimetry, dilatometry, high-temperature resistivity, and the powder X-ray methods in the temperature range 700-1000 degrees and at P O2 = 1-10 -4.3 atm. The existence of a high-temperature (peritectic melting) boundary of phase stability was found. The temperatures of low-temperature phase decomposition were determined in air and under an oxygen atmosphere. The change in oxygen content was determined for the 2212 phase in the temperature range 700-860 degrees C and at P O2 = 0.21-10 -3.7 atm by iodometric analysis of quenched samples. It was found that in the single-phase region, the change in oxygen nonstoichiometry had an insignificant influence on T c . It was also shown that the slow cooling of samples led to a significant decrease in T c and transport j c due to partial phase decomposition

Development of microstructure and superconductivity of silver-clad Bi(2223) composite tapes in the process of heat treatment

International Nuclear Information System (INIS)

Guo, Y.C.; Liu, H.K.; Dou, S.X.

1994-01-01

A systematic study on the development of phase composition, microstructure and superconducting properties (critical temperature Tc and critical current density J c ) in silver-clad (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O 10 composite tapes during the process of heat treatment has been conducted using X-ray diffraction, scanning electron microscopy and electrical measurements. The correlation between the tape's high Tc phase purity, microstructure and superconducting properties at different heat treatment stages has been carefully analysed and explained. The results indicate that pure high Tc phase, high degree of grain alignment, high mass density and good connection between grains are all essential for superconducting tapes to carry a large current. With the optimized process parameters, a critical current density J c up to 32665 A cm -2 (corresponding critical current, 42.3 A) at 77 K and self-magnetic field for silver-clad (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O 10 superconducting composite tapes has been achieved. (orig.)

Preparation of Bi-Pb-Sr-Ca-Cu-O high Tc thick films on Ag or MgO substrate with superconductor paste; Bi kei ko Tc chodendo paste ni yoru Ag, MgO kibanjo eno atsumaku sakusei

Energy Technology Data Exchange (ETDEWEB)

Takabatake, N. [Ishikawa Technical High School, Ishikawa (Japan); Tsubota, T.; Ishikawa, T.; Ohashi, K. [Kanazawa Institute of Technology, Ishikawa (Japan)

1995-07-15

The following were reported on making Bi series superconducting thick films by a wet method. A paste was made by adding PSO (or ethanol solution of ethylenegrycol) of Yushiro Chemical Industry Co., Ltd. as a binder to a Bi series 2223 single-phase powder sample (blending composition Bi:Pb:Sr:Ca:Cu=1.8:0.4:2:2:3.2); the sample was then coated on an Ag (or MgO) substrate with a brush; after being dried at 105{degree}C for one hour, it was thermally decomposed at 700{degree}C for one hour; then, the process of prissurized forming (at pressure 2 to 5 ton f/cm{sup 2}) and of sintering at 845{degree}C for 20 hours or more were performed on the sample to form a thick film sample. A critical temperature Tc, critical current density Jc, etc., were measured on such thick film sample. As a result, nearly same values were obtained as Tc (93K) and Jc (84A/cm{sup 2}) which were those of a bulk sample made by using the same powder sample, pressurizing at 2 ton f/cm{sup 2} for pelletizing, and sintering at 845{degree}C for 20 hours. 6 refs., 7 figs., 1 tab.

Desafío con wssv bajo fluctuaciones de temperatura

OpenAIRE

Sonnenholzner, Stanislaus

2002-01-01

Desafío con WSSV bajo fluctuaciones de temperatura En trabajos anteriores sobre el efecto de la temperatura del agua sobre la supervivencia del camarón infectado con el virus de la Mancha Blanca, se demostró que una temperatura constante de 33ºC por 8 días genera una respuesta inmune en el camarón correlacionada a una supervivencia superior al 90%, lo cual se tradujo posteriormente en una propuesta práctica de cultivo de camarón en estanques con invernaderos, actualmente en evaluación e...

High Temperature Protonic Conductors by Melt Growth

Science.gov (United States)

2006-11-21

A.R. de Arellano-López, A. Sayir. “Microestructura y Comportamiento Plástico de Perovsquitas Conductoras Protónicas de Alta Temperatura ”. Bol. Soc...Conductores Protónicos de Alta Temperatura Crecidos por Fusión de Zona Flotante”. VII Reunión Nacional y VI Conferencia Iberoamericana (Electrocerámica

Modificaciones en la distribución espacial de la temperatura y la humedad relativa como resultado del crecimiento urbano: el caso de la ciudad de Bahía Blanca, Argentina

Directory of Open Access Journals (Sweden)

F. Ferrelli

2016-04-01

Full Text Available El crecimiento de las ciudades genera modificaciones en la atmósfera local que pueden afectar la confortabilidad y calidad de vida de la población. El objetivo del presente trabajo fue comparar la evolución de la isla de calor de verano e invierno entre los años 1985 y 2014 en Bahía Blanca (Argentina. Esta ciudad ha sufrido un importante aumento de la población y de las actividades industriales en los últimos años. Se estudió el aumento de la zona urbana construida, las variaciones espaciales de temperatura y humedad relativa y el crecimiento de la población. Se calcularon índices de confort climático (Humidex, Termohigrométrico y Temperatura Equivalente. La zona urbana construida se extendió más de 110 km² y el incremento de la población fue de 22,4 %. Las modificaciones en el espacio urbano, junto con una mayor densidad de edificios, generaron cambios en las temperaturas de verano de 1985 y 2014. En la primera el centro de la ciudad fue más cálido que las zonas periféricas. La zona más confortable fue la costera. En 2014, en el centro de la ciudad se presentaron las temperaturas más altas y las zonas más confortables fueron las periféricas y los parques. Las mediciones de invierno no registraron diferencias considerables entre sí en las mediciones nocturnas. Los resultados demostraron que el crecimiento de las edificaciones y el incremento de la población de Bahía Blanca modificaron la distribución espacial de la temperatura y la humedad relativa y generaron situaciones de desconfort. Estos resultados generaron información necesaria para futuros planes de desarrollo urbano.

Ajuste de las curvas tensión-deformación a alta temperatura de un acero microaleado Nb-Ti

Directory of Open Access Journals (Sweden)

Pol, L. A.

1997-02-01

Full Text Available A series of hot plane strain compression tests have been conducted on a Nb-Ti microalloyed steel in a Servotest machine on samples of approx. 10 mm in thickness. Two sets of tests at strain rates of 5 s^-1 and 15 s^-1 were used and monitored the stress-strain behavior at deformation temperatures varying from 850 to 1,025 °C. The experimental data were corrected for friction, deviation from plane strain compression (PSC conditions and adiabatic rise of temperature, to give the isothermal equivalent tensile stress-strain curves. Thereafter these curves have been modeled by two types of equations depending on the softening mechanism operating during the deformation process and calculated the value of the coefficients in the equation by the application of a Taylor series around an initial point close to the solution. Finally, by the application of the least squared method, the previous values are compared to the experimental ones in order to determine an optimized value of the coefficients in the equations which model the stress-strain behaviour of the steel.

Se ha realizado una serie de ensayos de compresión plana en caliente en muestras de un acero microaleado con niobio y titanio en una máquina Servotest, en probetas trapezoidales de aproximadamente 10 mm de espesor. Se efectuaron dos series de ensayos con dos velocidades de deformación, 5 y 15 s^-1, y temperaturas de deformación entre 850 y 1.025 °C. Los datos experimentales fueron corregidos por rozamiento probeta-herramientas, ausencia de condiciones de deformación plana y aumento de la temperatura en la muestra debido a que la deformación no es estrictamente adiabática, para obtener las curvas isotermas equivalentes en tracción. Dichas curvas han sido modelizadas según dos tipos de ecuaciones constitutivas que caracterizan el proceso de ablandamiento que tiene lugar concurrente a la deformación. Se calculan los coeficientes de las mismas por

Caracterização de fatores que afetam a germinação de teca (Tectona grandis: temperatura e escarificação

Directory of Open Access Journals (Sweden)

Rodrigo Barros Rocha

2011-04-01

Full Text Available A germinação lenta e irregular das sementes é uma limitação para a produção de mudas de teca (Tectona grandis. Embora métodos práticos estejam disponíveis poucos estudos quantificaram sistematicamente o efeito do aquecimento e da escarificação para a superação da dormência. O emprego de altas temperaturas pode ser realizado através de um coletor solar, aparelho de montagem simples que permite a captação da energia solar e transformação em energia calorífera. O objetivo deste trabalho foi avaliar a interação dos fatores "aquecimento" e "escarificação" na superação da dormência dos diásporos de teca avaliando o desempenho do coletor solar. Foi avaliado experimento em delineamento de fatorial completo com quatro níveis do fator "aquecimento" (A1 - solarizador, A2 - estufa a 80ºC (12h, A3 - estufa a 80ºC (4h/3dias, A4- sem aquecimento e três níveis do fator "escarificação" (E1 - escarificação física, E2 - escarificação química e E3 - sem escarificação, totalizando 12 tratamentos com cinco repetições de 25 diásporos por parcela. O teste F a 1% de probabilidade indicou a ocorrência de interação significativa entre os fatores "aquecimento" e "escarificação", resultado da menor germinação dos diásporos que foram escarificados após aquecimento. A utilização de altas temperaturas na ausência de escarificação caracterizou os tratamentos de melhor desempenho para a superação da dormência. O menor desempenho associado aos maiores custos e riscos para manipulação desencorajaram o uso da escarificação química na superação da dormência. A alternância de temperaturas favoreceu a germinação, sendo que o coletor solar mostrou-se uma alternativa prática, viável e de menor custo para a superação da dormência em teca.

SULL'AUMENTO DI TEMPERATURA NEL MANTELLO DELLA TERRA PER COMPRESSIONE ADIABATICA

Directory of Open Access Journals (Sweden)

P. E. Valle

1951-06-01

Full Text Available Viene stabilita una relazione fra la densità, la temperatura e lavelocità delle onde longitudinali e trasversali relativa ad una particolaretrasformazione adiabatica di un solido ideale.L'equazione, applicata al mantello della. Terra, conduce al risultatoche la temperatura in prossimità del nucleo sarebbe circa 1,24volte, la temperatura alla profondità di 1000 km, se la compressionedei materiali fosse avvenuta adiabaticamente.

Texture of high temperature superconductor thick films TI-1223 and TI-2223/LaAlO3 deposited by spray pyrolysis

International Nuclear Information System (INIS)

Nguyen Xuan, H.; Beauquis, S.; Galez, Ph.; Jorda, J.L.; Phok, S.; De-Barros, D.

2004-01-01

Superconducting TI-1223 and TI-2223 films have been prepared in a two steps process: deposition of Ba:Ca:Cu = 2:2:3 precursor by spray pyrolysis and ex-situ thallination. Pure textured TI-1223 films with good superconducting properties (T c =113 K and J c =0.7 MA/cm 2 at 77 K, 0T) have been obtained. Almost pure TI-2223 films have been obtained when precursor films have been thallinated with fluorinated sources. (orig.)

Synthesis of Bi{sub 1.8}Pb{sub 0.4}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} superconductor

Science.gov (United States)

Smith, M.G.

1996-10-29

Two-powder processes for the synthesis of superconducting (Bi, Pb)-2223/Ag-clad wires by the oxide-powder-in-the-robe are provided. The first precursor powder, of nominal stoichiometry CaCuO{sub x}, is a solution-synthesized mixture of Ca{sub 0.45}Cu{sub 0.55}O{sub 2} and CaO. Using these oxide precursor mixtures, superconducting tapes with well-aligned grains and reproducible critical current densities J{sub c} in the range of 20,000 to 26,000 A/cm{sup 2} at 75 K in self-field after annealing less than 200 hours were obtained. 2 figs.

Níveis de energia metabolizável para frangos de corte de 1 a 21 dias de idade mantidos em ambiente de alta temperatura Metabolizable energy levels for broiler chicks from 1 to 21 days of age under high environmental temperature

Directory of Open Access Journals (Sweden)

Rita Flávia Miranda de Oliveira

2000-06-01

Full Text Available Quatrocentos e cinqüenta pintos de corte machos, Avian Farms, com peso médio de 48±0,3 g, foram utilizados em um experimento conduzido em câmaras climáticas, para avaliar o efeito dos níveis de energia metabolizável (2850, 2925, 3000, 3075 e 3150 kcal de EM/kg, entre 1 e 21 dias de idade, mantidos em ambiente de alta temperatura (34ºC e 60% UR. O delineamento utilizado foi o inteiramente casualizado, com cinco tratamentos, nove repetições e dez aves por unidade experimental. As características estudadas foram desempenho e composição de carcaça, em que a estimativa da exigência de energia metabolizável das aves foi feita por meio de regressão linear ou quadrática, conforme o melhor ajuste. O ganho de peso, o consumo de energia metabolizável e as deposições de proteína e gordura na carcaça aumentaram, enquanto a conversão alimentar dos pintos reduziu de forma linear com os tratamentos. O rendimento de carcaça das aves não foi influenciado pelos níveis de EM da ração. Os níveis de EM da ração modificaram a composição da carcaça e aumentaram o peso de gordura abdominal. Os pintos de corte de 1 a 21 dias de idade, mantidos sob alta temperatura, exigem, no mínimo, relação energia:proteína de 13,6 para melhor desempenho e deposição de proteína na carcaça.Four hundred and fifty Avian Farms male broilers chicks with 48±0.3g of live weight were used in an experiment carried out at climatic chambers to evaluate the effect of the metabolizable energy levels (2850; 2925; 3000; 3075 and 3150 kcal of ME/kg, from 1 to 21 days, maintained at high environmental temperature (34ºC and 60% RH. A completely randomized design, with five treatments (ME levels, nine replicates and ten birds per experimental unit, was used. Performance and carcass composition were evaluated and the metabolizable energy requirement of the birds were obtained by linear or quadratic regression, according to the best fit. Weight gain

Oxidación a alta temperatura de un acero ASTM A335 P92 en contacto con una mezcla de sales de

OpenAIRE

Jessica Rodríguez Pérez; Eduardo Santos Sánchez; Darío Yesid Peña Ballesteros; Anderson Sandoval Amador; Hugo Armando Estupiñán Durán

2016-01-01

En esta investigación se evaluó la oxidación del acero ASTM A335 P92 en una mezcla de sales 40% K2SO4 - 60% NaCl a temperaturas de 500ºC a 700ºC, a intervalos de 50°C con tiempos de exposición de 1, 3, 10, 30, 100 y 150 horas, utilizando la norma estandarizada por la Federación Europea de Corrosión. Se realizó análisis metalográfico y de dureza antes y después del ensayo para identificar el posible cambio estructural; se realizan pruebas de difracción de rayos X (DRX), microscopía electrónica...

ALTA: A BRDF analysis library

OpenAIRE

Belcour , Laurent; Barla , Pascal; Pacanowski , Romain

2014-01-01

International audience; In this document, we introduce ALTA, a cross platform generic open-source library for Bidirectional Reflectance Distribution Function (BRDF) analysis. Among others, ALTA permits to estimate BRDF models parameters from measured data, to perform statistical analysis and also to export BRDF data models in a wide variety of formats.

Software para Controle de Temperatura em Estufas

OpenAIRE

Silva, Antonio Carlos Alves; Universidade Federal de Lavras; Kanazawa, Edna Mie; Universidade Federal de Lavras; de Carvalho, Karina Dutra; Universidade Federal de Lavras; Kinoshita, Vanessa Godoy; Universidade Federal de Lavras; Uchoa, Joaquim Quinteiro; Universidade Federal de Lavras; Lacerda, Wilian Soares; Universidade Federal de Lavras; Schneider, Bruno de Oliveira; Universidade Federal de Lavras

2004-01-01

Neste trabalho é apresentado o projeto desenvolvido para controle de temperatura em estufas, denominado CTE, utilizando uma Interface de Aquisição e Controle de Dados. Todo o controle é feito via software, onde pode-se optar por dois tipos de controle: o controle automático, onde é possível definir-se a temperatura mínima e máxima; ou o controle manual, onde o usuário poderá optar por acionar periféricos de aquecimento, resfriamento e desligamento da estufa. Foi desenvolvida também uma interf...

Ag doped (Bi1.6Pb0.4Sr2CaCu2O8+δ textured rods

Directory of Open Access Journals (Sweden)

Díez, J. C.

2008-06-01

Full Text Available In this work, superconducting samples of (Bi1.6Pb0.4Sr2CaCu2O8+δ with Ag additions have been studied. (Bi1.6Pb0.4Sr2CaCu2O8+δ + x wt.% Ag (with x = 0, 1 and 3 powders were synthesized using a sol-gel method. The obtained powders were used as precursors to fabricate long textured cylindrical bars through a floating zone melting method. A drastic change on the microstructure has been found when comparing with undoped Bi2Sr2CaCu2O8+δ samples. The results showed that electrical resistivity at room temperature, critical current as well as flexural strength are improved when Ag is added to these Pb doped samples, while critical temperature does not change. On the other hand, it has been found that samples with composition (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag shown E-I curves with very high sharpness values on the zone of the superconducting to normal transition, reaching n-values (E∼In as high as 45 at 65K.Se han preparado polvos cerámicos de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + x % Ag en peso (con x = 0, 1 y 3 mediante un proceso sol-gel. Estos polvos se han utilizado para fabricar precursores que se texturaron por medio del método de fusión zonal flotante. Se ha encontrado un gran cambio en la microestructura cuando se compara con muestras de composición pura Bi2Sr2CaCu2O8+δ. Tanto la resistividad eléctrica a temperatura ambiente, como la corriente crítica, así como la resistencia a flexión se mejoran cuando la Ag se adiciona a estas muestras dopadas con Pb, mientras que no se observa cambio en la temperatura crítica. Por otra parte, se ha encontrado que las muestras de composición (Bi1.6Pb0.4Sr2CaCu2O8+δ + Ag presentan una gran pendiente de la curva E-I en la zona de transición entre el estado superconductor y el estado normal. Con estas composiciones, se han encontrado valores de n (E∼In de hasta 45 a 65K.

Modelación matemática del efecto de la temperatura en la actividad y la estabilidad térmica de la inulinasa de Kluyveromyces marxianus NRRL Y-7571

Directory of Open Access Journals (Sweden)

Jesús Diestra Balta

2015-01-01

Full Text Available Un modelo matemático se utilizó en este estudio para describir el efecto de la temperatura en la actividad y la estabilidad térmica (condiciones no reactivas de la inulinasa de Kluyveromyces marxianus NRRL Y-7571. El modelo se tomó de la literatura, el cual se desarrolló utilizando la ecuación de Arrhenius y los datos experimentales. Una ecuación cinética de primer orden se asumió para la inactivación enzimática. Los parámetros del modelo se determinaron por regresión lineal y no lineal, reportando los intervalos de confianza. Los datos experimentales demostraron que la actividad máxima actuando en sacarosa e inulina se alcanzó a 55 °C y que estas actividades fueron altamente sensibles a temperaturas más altas. Además, la actividad inulolítica fue más estable térmicamente que la de invertasa en el rango de 48 a 60 °C.Utilizando el modelo, la temperatura del proceso para la hidrólisis de sacarosa e inulina se determinó en la intersección de las curvas de la actividad relativa y el tiempo de vida media relativo, resultando 49 °C para ambos procesos. Aunque este modelo se utilizó con referencia a la hidrólisis de la sacarosa e inulina, el enfoque es una herramienta útil que se puede aplicar a otros procesos enzimáticos para la determinación de la temperatura de operación, la que es últimamente determinada por una evaluación económica.

Broiler surface temperature distribution of 42 day old chickens Distribuição da temperatura superficial de frangos de corte com 42 dias de idade

Directory of Open Access Journals (Sweden)

Irenilza de Alencar Nääs

2010-10-01

apanhados e transportados para o abate, foram registradas temperaturas superficiais infravermelho durante o dia.. Os resultados dos termogramas das regiões com penas e sem penas foram comparados, durante o 42º dia. Alta correlação entre regiões sem penas e a temperatura ambiente foi encontrada, mostrando que estas áreas respondem rapidamente a alterações no ambiente do alojamento. Duas funções foram desenvolvidas para predizer a temperatura superficial das regiões com e sem penas, do corpo de frangos com 42 dias, sendo conhecida a temperatura do ar do ambiente.

Carrot seed germination and vigor in response to temperature and umbel orders Germinação e vigor de sementes de cenoura em resposta a temperatura e ordens de umbela

Directory of Open Access Journals (Sweden)

Roseane Sousa Pereira

2008-04-01

Full Text Available Several factors may influence carrot (Daucus carota L. crop establishment. High temperatures (35 - 40°C, for instance, may delay or inhibit carrot seed germination in the field and so compromise the stand establishment. Carrot seeds from superior umbel orders usually have better physiological quality than those of lower umbel orders. These seeds from superior umbel orders may also show a better performance in adverse conditions. In addition, seeds from different ages show differences in vigor, which affect the stand establishment, mainly under adverse conditions. The aim of this study was to verify the germination at high temperatures and the carrot seed vigor of different umbel orders of 'Brasília', as well as the different 'Alvorada' seed lots. Preliminarily, 'Brasilia' seeds were incubated at temperatures ranging from 20 to 36°C. Also, seeds from the primary, secondary and tertiary umbel orders harvested separately from a basic seed production field and seeds from lots harvested in 1998, 1999 and 2000 were analyzed to the following tests: germination at 20°C (optimum and 35°C (adverse, accelerated aging, cold test, seedling emergence in greenhouse and mass of 100 seeds. High temperatures reduced carrot seed germination. Seeds germinated better at 20°C than 35 or 36ºC. Seeds from primary and secondary orders, as well as less aged seed lots, had higher vigor and germination at high temperature.Vários fatores podem influenciar no estabelecimento da cultura da cenoura (Daucus carota L.. Altas temperaturas (35 - 40°C, por exemplo, podem retardar ou inibir a germinação das sementes de cenoura no campo, comprometendo assim o estabelecimento de plântulas. Sementes oriundas de umbelas de ordem superior geralmente apresentam melhor qualidade fisiológica do que aquelas de menor ordem. Estas sementes podem apresentar uma melhor performance no campo, principalmente sob condições adversas. Lotes de sementes armazenados por diferentes per

Temperaturas extremas en verano. Implicaciones en salud

Directory of Open Access Journals (Sweden)

Julio Díaz Jiménez

2005-12-01

Full Text Available El incremento que se ha detectado en las temperaturas estivales en los últimos años, unido las tendencias que se esperan para el clima durante el próximo siglo, hacen prever un aumento en la frecuencia e intensidad de los eventos térmicos extremos, fundamentalmente olas de calor. La clara relación existente entre la temperatura y la mortalidad, hace necesaria una cuantificación para la caracterización de los efectos esperados de la temperatura sobre la mortalidad en las denominadas olas de calor.En este trabajo se presenta una descripción del estado del conocimiento de este problema, haciendo especial referencia a la ola de calor que asoló Europa en el verano de 2003, de cómo se han caracterizado las olas de calor y en base a ello de cuáles son las características que han de tener los planes de alerta y prevención encaminados a minimizar los efectos del calor sobre la salud de la población.

Influencia de la temperatura de austenización y tiempo de permanencia sobre el tamaño de grano en aceros ferrítico-martensíticos del tipo 9Cr1MoVNb utilizados en calderas supercríticas

Directory of Open Access Journals (Sweden)

Gutiérrez-Urrutia, L.

2001-04-01

Full Text Available The aim of the present work is to determine the influence of austenitizing temperature holding time and heating velocity on grain size of ferritic-martensitic type 9CrlMoVNb steels developed for Oak Ridge National Laboratories & Combustion Engineering, T91/P91^[1] Steels (USA and X10CrMoVNb 9.1 (Europe. The potential benefits of this material, in term of high resistance, good ductily and oxidation resistance, weldability and in particular good high temperature creep strength, are now widely acknowledged, particulary by supercritical boilers (P = 300 bar, T = 550±50 °C. The studied steels have been produced in, high frecuency induction vacum furnaces and hot-rolled.

Se estudia la influencia de la temperatura de austenización, tiempo de permanencia a esta temperatura y velocidad de calentamiento sobre el tamaño de grano de varios aceros ferrítico-martensíticos de última generación del tipo 9CrlMoVNb, desarrollados por Oak Ridge National Laboratories (ORNL conjuntamente con Combustion Enginering en USA, conocidos por ASME/ASTM por las designaciones T91/P91^[1] y en Europa como X10CrMoVNb9.1. Son aceros ductiles y tenaces que presentan muy buenas propiedades de resistencia a fluencia, soldabilidad y conductividad térmica. Son cada vez más utilizados como tubos de alta temperatura (550±50 °C y presión (300 bar en calderas supercríticas para centrales térmicas avanzadas. Los aceros estudiados se han fabricado en hornos de inducción de alta frecuencia al vacío y laminados en caliente.

Propiedades volumétricas y viscosimétricas de las mezclas binarias de N,N- Dimetilformamida + 1-pentanol a varias temperaturas

Directory of Open Access Journals (Sweden)

Manuel S. Páez

2014-01-01

Full Text Available Se determinaron las densidades y viscosidades de las mezclas binarias de N,N-Dimetilformamida (DMF + 1-pentanol sobre todo el intervalo de concentraciones a las temperaturas de (283,15, 288,15, 293,15, 298,15 y 313,15 K utilizando un densímetro de tubo vibratorio Anton Paar DMA 5000 y un viscosímetro Anton Paar AMVn respectivamente. Se calcularon los volúmenes molares de exceso , las desviaciones de viscosidad, los coeficientes B de viscosidad y los parámetros de activación del flujo viscoso. Se discutieron los efectos de la concentración del 1-pentanol y de la temperatura sobre los parámetros previamente mencionados. Los resultados fueron interpretados en términos de interacciones soluto-solvente en medios orgánicos. Los volúmenes molares de exceso resultaron ser negativos, y fueron atribuidos a la presencia de varios factores: fuerzas atractivas tipo puentes de hidrógeno soluto-solvente, fuerzas físicas más débiles como la fuerza bipolar o cualquier otra fuerza de este tipo; así como, al acomodamiento de las moléculas del alcohol en los espacios de las moléculas de la DMF. Las desviaciones de viscosidad son altas y negativas en todo el intervalo de concentraciones y se incrementan al aumentar la temperatura, lo cual podría indicar la presencia de interacciones específicas entre las moléculas de 1-pentanol y la DMF, mientras que los altos valores negativos se pueden interpretar considerando la fuerza de los enlaces de hidrógeno, la forma y el tamaño de las moléculas estudiadas.

Mid-term periodicities and heliospheric modulation of coronal index and solar flare index during solar cycles 22-23

Science.gov (United States)

Singh, Prithvi Raj; Saxena, A. K.; Tiwari, C. M.

2018-04-01

We applied fast Fourier transform techniques and Morlet wavelet transform on the time series data of coronal index, solar flare index, and galactic cosmic ray, for the period 1986-2008, in order to investigate the long- and mid-term periodicities including the Rieger ({˜ }130 to {˜ }190 days), quasi-period ({˜ }200 to {˜ }374 days), and quasi-biennial periodicities ({˜ }1.20 to {˜ }3.27 years) during the combined solar cycles 22-23. We emphasize the fact that a lesser number of periodicities are found in the range of low frequencies, while the higher frequencies show a greater number of periodicities. The rotation rates at the base of convection zone have periods for coronal index of {˜ }1.43 years and for solar flare index of {˜ }1.41 year, and galactic cosmic ray, {˜ }1.35 year, during combined solar cycles 22-23. In relation to these two solar parameters (coronal index and solar flare index), for the solar cycles 22-23, we found that galactic cosmic ray modulation at mid cut-off rigidity (Rc = 2.43GV) is anti-correlated with time-lag of few months.

Mechanism of the formation of silver-sheathed HTSC ceramics and its fine structure

International Nuclear Information System (INIS)

Blinova, Yu.V.; Sudareva, S.V.; Krinitsina, T.P.; Romanov, E.P.; Akimov, I.I.

2005-01-01

Electron microscopical data are reported which point to the fact that two mechanisms of formation of main superconducting phase 2223 in Bi,Pb-2223/Ag exist: liquid phase mechanism and solid-phase one. Along crystallite boundaries the spherical outlined by Ag interlayers are observed. These are former eutectic liquid droplets of ∼ 2223 composition from which Ag is liberated on solidification. In the initial stage of phase formation inside of a 2212 phase the platelets of phase 2223 are found out with the same orientation as the matrix (a solid-phase mechanism). Certain relationships of structure to superconducting properties are shown [ru

Influência de diferentes superfícies na temperatura e no fluxo de energiaInfluência de diferentes superfícies na temperatura e no fluxo de energia: um ensaio experimental / Influence of different surfaces on the temperature and energy flux: an experimental trial

Directory of Open Access Journals (Sweden)

Elis Dener Lima Alves

2012-04-01

Full Text Available ResumoO meio urbano tem apresentado sérios problemas ambientais os quais prejudicam a qualidade de vida das pessoas. Um dos problemas mais relatados se refere às altas temperaturas registradas nas cidades. Dessa maneira, o objetivo deste trabalho foi analisar a variabilidade da temperatura superficial e o fluxo de energia em diferentes tipos de uso do solo no meio urbano. Para tanto, utilizou-se de um termômetro infravermelho (TD-920 para a medição da temperatura superficial de seis tipos de superfícies. As medições foram realizadas de hora em hora, em um período de 24 horas. Além da temperatura, foram observadas a nebulosidade, os tipos de nuvens e a ausência ou não de precipitação. Os resultados mostraram que as nuvens, a nebulosidade e a precipitação têm influência direta nos padrões da temperatura e do fluxo de energia. Notou-se que as superfícies artificiais (asfalto e concreto apresentaram os maiores valores térmicos e os maiores fluxos de energia, enquanto que superfícies naturais (grama e solo nu apresentaram os menores valores, tendo o asfalto apresentado, em média, 12% a mais de emissão de energia em relação à grama. Portanto, ressalta-se a urgente necessidade de se repensar o uso dos materiais urbanos, para uma melhor qualidade de vida das pessoas.AbstractThe urban environment has presented serious environmental problems which affects the our quality of life. One of the most reported issues refers to the high temperatures recorded in cities. Thus, this study aimed to analyze the variability of surface temperature and the energy flux in different types of land use in urban areas. For this, we used an infrared thermometer (TD-920 in order to measure the surface temperature on six different types of earth surfaces. All the measurements were made every hour over a period of 24 hours. In addition to temperature were observed cloud cover, cloud types, and absence of precipitation. The results showed that the

Embalse de Puente Alta

OpenAIRE

Isabel Crespo, Josué

2014-01-01

El presente proyecto de construcción define todas las actuaciones necesarias para la realización de las obras del Embalse de Puente Alta, ubicado en el término municipal de Revenga, provincia de Segovia. El proyecto se plantea debido a las previsiones de fuerte crecimiento poblacional, con motivo de la llegada del Tren de Alta Velocidad, puesto que el mantenimiento de la situación actual podría causar en su momento un déficit estructural en esta zona.

Variación diaria de la temperatura corporal en dos especies de lagartos nocturnos (Squamata, Gekkonidae, Homonota con comentarios sobre el uso de refugios

Directory of Open Access Journals (Sweden)

Cruz, Félix B.

2004-09-01

Full Text Available Poco es lo que se conoce sobre la variación de la temperatura corporal de lagartos nocturnos. Se sabe que algunos lagartos nocturnos termorregulan durante el día. El tamaño corporal y el comportamiento, a su vez, pueden estar relacionados con la inercia térmica. Individuos de Homonota borelli y H. darwini fueron expuestos a tres situaciones, a refugios cálidos (la temperatura nunca fue menor a los 34 ºC, b refugios con una temperatura inferior a los 28-30 ºC, y c se les permitió escoger entre cada una de las opciones anteriores. La temperatura corporal en general y el patrón diario fueron similares en ambas especies siendo más altas durante el día. Cuando los lagartos eligieron los refugios, se observaron diferencias entre las especies, H. borelli usó más los refugios con fuente de calor en tanto que H. darwini usó refugios sin fuente de calor. El tamaño corporal y la distribución geográfica podrían estar relacionados con las diferencias observadas. Very little is known about diel variation in body temperature among nocturnal lizards. Some nocturnal lizards thermoregulate during the day, and body size plus behaviour may be related to the amount of thermal inertia. Lizards of the species Homonota borelli and H. darwini were either exposed to three different situations a a heated retreat site (never below than 34 º C, b a retreat with a temperature lower than 28-30 º C, and c where lizards were allowed to choose between a warm or a cool retreat. Body temperatures and diel pattern were similar for both species. Body temperatures were higher during the day. When lizards choose for retreats, differences were observed, H. darwini preferred cool retreats, whereas H. borelli used the warmer ones. Body size, coloration and geographic distribution may be related to the different patterns observed.

Efecto de la temperatura sobre coloides de suelos agrícolas mediante dispersión dinámica de la luz

Directory of Open Access Journals (Sweden)

Túlio Armando Lerma

2015-12-01

Full Text Available La materia orgánica y la fracción coloidal son los principales componentes edafológicos que se ven afectados por la quema indiscriminada de los matorrales. En consecuencia, por acción de las altas temperaturas se produce un deterioro de la estructura, pérdida de la capacidad de intercambio catiónico (CIC y disminución de la fertilidad de los suelos. Por otro lado, se ha planteado el uso de tratamiento térmico in situ como estrategia de cimentación de suelos arcillosos en la construcción de obras civiles. Sin embargo, el efecto de la temperatura sobre la fracción coloidal sólo se ha evaluado frente a propiedades mecánicas; pocos estudios en relación a propiedades de importancia agrícola como la CIC, la estructura y la susceptibilidad a la erosión han sido realizados. El objetivo del presente trabajo fue estudiar mediante dispersión dinámica de la luz (DLS el efecto de la temperatura sobre la fracción coloidal de suelos agrícolas. Para ello se recolectaron y caracterizaron dos muestras de suelos procedentes de los departamentos de Córdoba y Valle del Cauca. La fracción coloidal fue extraída mediante una variante del método de Bouyoucos y sometida a diferentes tratamientos térmicos (desde 150 a 550 °C. Las muestras se caracterizaron por análisis elemental, FT-IR, DLS y se evaluó su CIC. Se concluyó que las propiedades de la fracción coloidal son fuertemente alteradas por efecto de la temperatura, además de evidenciarse una disminución de la CIC (desde 76 a 35 y desde 103 a 26 cmol(+/kg de suelo, el incremento del tamaño de partícula (desde 639 ± 165 a 1250 ± 435 y 606 ± 102 a 1540 ± 320 para S-Córdoba y S-Valle, respectivamente así como la eliminación de la materia orgánica.

MONITORAMENTO DA TEMPERATURA NO INTERIOR DE CHAPAS AGLOMERADAS DURANTE O PROCESSO DE PRENSAGEM

Directory of Open Access Journals (Sweden)

Elio José Santini

2005-03-01

Full Text Available O objetivo do presente trabalho foi analisar o comportamento da temperatura nas faces e no miolo de chapas de partículas aglomeradas, coladas com 8% de adesivo (base peso seco das partículas tanino-formaldeído. As chapas foram produzidas com três repetições por tratamento, com massa específica nominal de 0,7 g/cm³ e pressão específica de prensagem de 27 kgf/cm². Os tratamentos basearam-se na utilização de flocos de pinus (Pinus elliottii e partículas de eucalipto (Eucalytus sp, sendo que os flocos de pinus apresentavam três diferentes comprimentos nominais (40, 75 e 110 mm e duas espessuras (0,5 e 1,0 mm. Também foram analisados duas temperaturas de prensagem (140 e 180°C e dois teores de umidade nominal do colchão (17 e 21%. A temperatura no interior dos painéis durante a prensagem foi obtida por meio de fios para termopares tipo K (cromo-alumel. Os gráficos da temperatura em função do tempo de prensagem mostraram uma rápida elevação da temperatura nos primeiros 100 segundos de prensagem, mantendo-se num plateau possivelmente após atingir a temperatura de ebulição da água. A temperatura voltou a aumentar, de forma mais gradual, após a perda de grande parte da umidade do colchão. Observa-se que colchões formados por flocos de maior espessura apresentaram elevação mais rápida de temperatura no miolo. O principal fator que influenciou na velocidade de elevação da temperatura no miolo dos painéis aglomerados foi o teor de umidade do colchão, sendo que quanto maior o teor de umidade, mais rápida foi a elevação da temperatura.

Estimation of the resource and technological prospective of geothermal energy in Mexico (Annexe 3 in 'A vision of year 2030 on the use of the renewable energies in Mexico'); Estimacion del recurso y prospectiva tecnologica de la geotermia en Mexico (Anexo 3 en 'Una vision al 2030 de la utilizacion de las energias renovables en Mexico')

Energy Technology Data Exchange (ETDEWEB)

Iglesias R, Eduardo; Arellano G, Victor; Torres R, Rodolfo Joaquin [Instituto de Investigaciones Electricas, Cuernavaca, Morelos (Mexico)

2005-08-15

Due to its individual geologic-structural characteristics, Mexico counts on abundant geothermal resources. At the moment we count on a database that includes 2,332 geothermal manifestations distributed in 27 of the 32 Mexican states, the geothermal resources are classified as high temperature and intermediate or low temperature resources. Those of high temperature can be used for the generation of electrical energy. Those of intermediate to low temperature are more appropriate for direct applications of the geothermal heat. As of today, in Mexico exist four geothermal fields of high temperature that are being exploded for the electrical generation. [Spanish] Debido a sus particulares caracteristicas geologico-estructurales, Mexico cuenta con abundantes recursos geotermicos. Actualmente contamos con una base de datos que incluye 2,332 manifestaciones geotermicas distribuidas en 27 de los 32 estados mexicanos, los recursos geotermicos se clasifican en de alta temperatura y recursos de temperatura intermedia a baja. Los de alta temperatura pueden utilizarse para la generacion de energia electrica. Los de temperatura intermedia a baja son mas apropiados para aplicaciones directas del calor geotermico. Actualmente en Mexico existen cuatro campos geotermicos de alta temperatura que estan siendo explotados para la generacion electrica.

INFLUENCIA DE LA TEMPERATURA EN EL COMPORTAMIENTO ALIMENTARIO DE Peltocephalus dumerilianus (TESTUDINES PODOCNEMIDAE

Directory of Open Access Journals (Sweden)

Alejandro De La Ossa L

2009-04-01

Full Text Available Objetivo. Analizar los comportamientos de alimentación bajo diferentes condiciones de temperatura en un grupo de neonatos de Peltocephalus dumerilianus (Testudines Podocnemididae. Materiales y Métodos. Los individuos experimentales fueron obtenidos mediante incubación en el laboratorio, se dividieron en 5 grupos al azar. Durante 2 meses con tres repeticiones a la semana se hicieron pruebas de temperatura utilizando dentro de las bandejas calentadores eléctricos, con registro continuo de temperatura mediante termómetro digital - 10 a + 60ºC (± 0.1ºC, procurando mantener un ritmo constante de incremento equivalente a 0,25ºC cada 10 minutos, hasta llegar a la temperatura seleccionada, que fue mantenida por 60 minutos en cada ensayo. Las temperaturas seleccionadas para cada ensayo, fueron: 26ºC, 30ºC, 34ºC, 38ºC y ambiente que fue de 26,8ºC en promedio. Fueron evaluados los siguientes parámetros: duración en minutos de la ingesta, tiempo de inicio de comportamientos agonísticos, presencia de dos tipos de despliegues característicos: morder y disputa por alimento. Resultados. En general todos los parámetros fueron significativos, a mayor temperatura el tiempo de ingestión fue mayor, a menor temperatura el volumen de consumo fue menor, a menor temperatura el inicio de los despliegues agonísticos fue mayor y se mantuvo una relación inversamente proporcional. Conclusiones. Los resultados mostraron que existe relación directamente proporcional entre la temperatura ambiental y los procesos de alimentación, además que se relacionaron con aspectos básicos del comportamiento lo cual se manifestó en los despliegues agonísticos observados.

Design and Test of a Thermal Triggered Persistent Current System using High Temperature Superconducting Tapes

Energy Technology Data Exchange (ETDEWEB)

Park, Dong Keun [Department of Electrical and Electronic Engineering, Yonsei University, Shinchon-Dong 134, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of); Kang, Hyoungku [Electro-Mechanical Research Institute, Hyundai Heavy Industries, Yongin (Korea, Republic of); Ahn, Min Cheol [Department of Electrical and Electronic Engineering, Yonsei University, Shinchon-Dong 134, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of); Yang, Seong Eun [Department of Electrical and Electronic Engineering, Yonsei University, Shinchon-Dong 134, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of); Yoon, Yong Soo [Department of Electrical Engineering, Ansan College of Technology, 671 Choji-Dong, Danwon-Gu, Ansan, 425-792 (Korea, Republic of); Lee, Sang Jin [Department of Electrical and Electronic Engineering, Yonsei University, Shinchon-Dong 134, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of); Ko, Tae Kuk [Department of Electrical and Electronic Engineering, Yonsei University, Shinchon-Dong 134, Seodaemun-Gu, Seoul 120-749 (Korea, Republic of)

2006-06-01

A superconducting magnet which is operated in persistent current mode in SMES, NMR, MRI and MAGLEV has many advantages such as high uniformity of magnetic field and reduced thermal loss. A high temperature superconducting (HTS) persistent current switch (PCS) system was designed and tested in this research. The HTS PCS was optimally designed using two different HTS tapes, second generation coated conductor (CC) HTS tape and Bi-2223 HTS tape by the finite element method (FEM) in thermal quench characteristic view. The CC tape is more prospective applicable wire in these days for its high n value and critical current independency from external magnetic field than Bi-2223 tape. Also a prototype PCS system using Bi-2223 tape was manufactured and tested. The PCS system consists of a PCS part, a heater which induces the PCS to quench, and a superconducting magnet. The test was performed in various conditions of transport current. An initial current decay appeared when the superconducting magnet was energized in a PCS system was analyzed. This paper would be foundation of HTS PCS researches.

Effect of temperature and time immersion of stage soaking on color grains of upland rice parboiled cultivars/ Efeito da temperatura e do tempo de imersão da etapa de encharcamento sobre a cor dos grãos de arroz parboilizado de cultivares de terras altas

Directory of Open Access Journals (Sweden)

Priscila Zaczuk Bassinelo

Full Text Available The parboiling is the hydrothermal treatment of paddy before processing. The objective of this study was to evaluate the influence of the temperature and immersion time step of soaking (independent variables on the color of the grain parboiled (dependent variable cultivars of upland rice (BRS Primavera and BRS Sertaneja. A central composite rotational design (DCCR was used, which includes a 22 full factorial, three replicates at the center point and four axial points, making eleven treatments. It was considered for the selection of hydrothermal conditions to be studied, the criterion of water absorption in the age group from 28% - 32%. In extreme conditions of soaking (high temperature and immersion time was observed in general that the grains of parboiled rice had higher color difference for the samples of grains of white rice. Therefore, the use of temperatures below 65 °C during the soaking tend to have grains with milder browning. After parboiling under different conditions of temperature and time of soaking, the change of color (?E* was greater in cv. BRS Sertaneja. It is possible to produce grains with different shades, depending on the conditions used. The choice will depend on the application that is intended or products in wich the rice will be employed.A parboilização consiste no tratamento hidrotérmico do arroz em casca antes do beneficiamento. O objetivo deste estudo foi avaliar a influência das variáveis temperatura e tempo de imersão da etapa de encharcamento sobre a cor dos grãos parboilizados de cultivares de arroz de terras altas (BRS Primavera e BRS Sertaneja. Utilizou-se um delineamento composto central rotacional (DCCR, que inclui um fatorial completo 22, mais três repetições no ponto central e quatro pontos axiais, totalizando onze tratamentos. Considerou-se para seleção das condições hidrotérmicas, o critério de absorção de água na faixa de 28% – 32%. Nas condições extremas do encharcamento (elevada

Progress report on neutron beam experiments in Thailand: effects of antimony substitutions on the critical temperature of Bi-Pb-Sr-Ca-Cu-O compounds

Energy Technology Data Exchange (ETDEWEB)

Sangariyavanich, A; Ampornrat, P [Office of Atomic Energy for Peace, Bangkok (Thailand)

1998-10-01

Effects of systematic substitutions of antimony for bismuth in Bi{sub 1.8-x}Pb{sub 0.2}Sb{sub x}Sr{sub 2}Ca{sub 3}Cu{sub 4}O{sub 10} have been investigated. Fabrication of the specimens has been performed by solid state reaction in air. The samples were sintered between 820degC - 843degC for 65 hours and subsequently quenched in liquid nitrogen. The critical temperatures of most specimens as determined by standard four-probe technique was higher than 100 K. Phase identification by X-ray diffraction technique indicated that `2223` and `2234` were the predominant phases in these samples. (author)

The effect of the ceramic core initial phase composition on the Ag-sheathed Bi-2223 tapes critical properties

International Nuclear Information System (INIS)

Nikulin, A.D.; Shikov, A.K.; Khlebova, N.E.; Antipova, E.V.; Dontsova, E.V.; Kazakov, E.G.; Medvedev, M.I.; Kozlenkova, N.I.; Shishov, V.N.; Akimov, I.I.

1993-01-01

Ag - sheathed superconducting tapes were fabricated using ''powder-in-tube'' method with powders of Bi 1.6 Pb 0.4 Sr 2 Ca 2 Cu 3.2 O x chemical composition prepared by the ''freeze-drying'' tecnique and taken as a core materials. The effect of ceramic core initial phase composition: the mixture of oxide non-superconducting phases - OP (typeI) and 50% OP + 50% OP ''2212''- phase (type II) on the critical current density was investigated as well as the ''annealing - cold pressing'' parameters. Multifilamentary superconducting tapes and the pancake coils were fabricated. (orig.)

Eficácia biológica de bifentrina aplicado em milho armazenado sob diferentes temperaturas Biological efficacy of applied bifenthrin in stored corn under different temperatures

Directory of Open Access Journals (Sweden)

Marco A. G. Pimentel

2005-06-01

Full Text Available Considerando-se as altas temperaturas nos graneleiros junto à esteira transportadora de grãos objetivou-se, neste trabalho, avaliar a influência da temperatura no momento da pulverização, sobre a eficácia biológica do bifentrina. Para isso, pulverizou-se o inseticida sobre grãos de milho dentro de uma câmara climática nas temperaturas de 25, 30, 35, 40, 45 e 50 ºC, com umidade relativa em torno de 55%. Após a pulverização e a cada 15 dias, até completar 90 dias, foram feitas as análises da eficácia biológica utilizando-se os insetos Sitophilus zeamais Motschulsky (Coleoptera: Curculionidae, Rhyzopertha dominica (Fabricius (Coleoptera: Bostrichidae e Tribolium castaneum (Herbst (Coleoptera: Tenebrionidae. Observou-se tendência decrescente da eficácia biológica do bifentrina com o aumento da temperatura do ar ambiente, no momento da pulverização e com o maior tempo de armazenamento dos grãos de milho, resultando em menor mortalidade dos insetos-praga.Considering the high temperatures in the granary ships alongwith the transporting mat, the objective of this paper was to evaluate the influence of the temperature at the moment of spraying on the biological effectiveness of the bifenthrin. For the purpose the insecticide was sprayed on maize grains inside a climatic chamber maintained at the temperatures of 25, 30, 35, 40, 45 and 50 ºC with relative humidity around 55%. After the spraying and every fifteen days up to 90 days, analyses of the biological effectiveness were made by using insects of the Sitophilus zeamais Motschulsky (Coleoptera: Curculionidae, Rhyzopertha dominica (Fabricius (Coleoptera: Bostrichidae and Tribolium castaneum (Herbst (Coleoptera: Tenebrionidae. A decreasing tendency of the biological effectiveness of the bifenthrin was observed with the increase of the air temperature at the moment of spraying and with the increased time of maize storage, resulting in a smaller mortality of the insect-pest.

Mortalidad diaria en la comunidad de Madrid (1986-1991 para el grupo de 45 a 64 años: su relación con la temperatura del aire

Directory of Open Access Journals (Sweden)

Pajares Ortíz Mª Sierra

1997-01-01

Full Text Available FUNDAMENTOS: Existen numerosos trabajos que relacionan la mortalidad con diferentes factores ambientales. Éstos se centran en la población general o en el grupo de personas mayores de 65 años, pero son escasos los que se refieren al grupo de 45 a 64 años, en el que la mortalidad tiene gran repercusión económica y social. El objeto del presente artículo es analizar la asociación existente entre la mortalidad diaria, tanto total como por diversas causas específicas, con la temperatura del aire en este grupo etario en la Comunidad de Madrid, de la cual las características climáticas extremas hacen especialmente interesante el trabajo. MÉTODOS: Se utiliza la modelización ARIMA según la metodología Box-Jenkins para el filtrado de las series de mortalidad diaria y de temperaturas. Entre los residuales se establecen funciones de correlación cruzada que permiten establecer una asociación entre las series eliminando los factores estacionales comunes, así como determinar el tiempo de desfase entre los extremos térmicos y los excesos de mortalidad. RESULTADOS: Existe una relación en forma de "V" entre la mortalidad diaria total y la temperatura. La mínima mortalidad se establece en una temperatura máxima diaria de 33ºC. La sobremortalidad por cada grado por debajo de 33ºC es del 0,8 %, mientras que por encima es del 3,0 %. Las funciones de correlación cruzada indican que esta asociación se da en los varones tanto por mortalidad total como por enfermedades circulatorias. En el caso de los altas temperaturas el efecto es inmediato, mientras que para las bajas hay que añadir otro efecto a los 10-13 días. CONCLUSIÓN: Existe una asociación estadísticamente significativa entre la mortalidad y los extremos térmicos en los varones de este grupo de edad. Los años potenciales de vida perdidos indican la magnitud del problema y la necesidad de articular medidas de prevención.

Nodo sensor para la medida ambiental de CO2, temperatura y humedad

OpenAIRE

Jara Burgos, Marcos

2007-01-01

En este documento se describe el diseño y la implementación de un nodo sen-sor para la medida ambiental del nivel de CO2, la temperatura y la humedad relativa. El sistema se basa en un interfaz directo sensor a microcontrolador para las medidas de temperatura y humedad relativa, mientras que para el sensor de CO2 se basa en una conversión analógica digital. El sistema utiliza un sensor resistivo para medir la temperatura, un sensor capacitivo para medir la humedad relativa y un sensor...

Center for Transportation Studies 24th annual transportation research conference, May 22-23, 2013, Saint Paul, Minnesota.

Science.gov (United States)

2013-05-01

The University of Minnesotas Center for Transportation : Studies is pleased to present its 24th Annual Transportation : Research Conference, May 22-23, 2013. The conference will : be held at the Saint Paul RiverCentre, 175 West Kellogg : Boulevard...

LA VARIACIÓN DE LAS TEMPERATURAS EXTREMAS EN LA 'COMARCA LAGUNERA' Y CERCANÍAS

Directory of Open Access Journals (Sweden)

Jairo Omar Inzunza-López

2011-01-01

Full Text Available Las series de temperaturas máxima y mínima diarias, con registros de al menos 30 años, de 23 estaciones meteorológicas de la Comarca Lagunera y lugares cercanos, fueron analizadas con las técnicas de regresión lineal simple y densidad de espectro potencial para obtener las tendencias y frecuencias significativas. Las series de 15 de las 23 estaciones presentaron tendencias significativas (P¿0.05 para ambas temperaturas. El promedio de las tendencias de temperatura máxima fue de -0.22 °C por decenio; pues 15 de las 23 series presentaron decrementos, 13 de forma significativa. El promedio de las tendencias de temperatura mínima fue de -0.085 °C por decenio; ya que 13 de 23 series presentaron tendencias negativas, 11 de forma significativa. La variación a largo plazo fue la predominante ya que los promedios de dimensión fractal fueron 1.46 y de 1.47 para temperatura máxima y mínima, respectivamente. La mayoría de las series presentaron frecuencias cuasibianuales, cuasi-trianuales y cuasi-tetra-anuales. En cinco estaciones se apreciaron frecuencias de 10 a 11 años para ambos tipos de temperatura; una estación presentó la frecuencia de 20 años en las dos temperaturas.

Planning and production of a low cost cryostat for electrical characterization of materials

OpenAIRE

Torsoni, G.B. [UNESP; Carvalho, C.L. [UNESP

2012-01-01

Os supercondutores a base de BiSrCaCuO apresentam três fases principais, Bi2Sr2CuO, Bi2Sr2CaCu2O e Bi2Sr2Ca2Cu3O com temperaturas críticas de 20 K, 80 K e 110 K, respectivamente. Desta forma, torna-se fundamental a caracterização elétrica de tais materiais a baixas temperaturas. Com este objetivo confeccionou-se um criostato para medidas de caracterização elétrica. Utilizando-se nitrogênio líquido (77 K), e controlando a pressão sobre o refrigerante, atingiu-se uma temperatura da ordem de 64 ...

Altas capacidades en el aula /

OpenAIRE

Conesa Muñoz., María Gregoria

2014-01-01

Las altas capacidades necesitan un tratamiento específico, del mismo modo que lo necesitan otros alumnos con dificultades para el aprendizaje, el hecho de que les sea más fácil aprender no significa que no se deban potenciar sus capacidades. Se analiza el tratamiento que han tenido las altas capacidades intelectuales a lo largo de los diferentes sistemas educativos, se ven las características más importantes que pueden tener estos niños y las diferentes vías de identificación y diagnóstico. ...

Engineering development of an HTS floating coil for the Mini-RT project

International Nuclear Information System (INIS)

Yanagi, Nagato; Mito, Toshiyuki; Morikawa, Junji

2004-01-01

A magnetically-levitated superconducting coil device, Mini-RT, has been constructed using a high temperature superconductor (HTS) for the purpose of examining a new magnetic confinement scheme of high-beta non-neutral plasmas. The floating coil is wound with silver-sheathed Bi-2223 tapes, and it is operated in the temperature range of 20-40 K. A number of studies and experiments were carried out in order to realize the necessary system. One of them was to demonstrate magnetic levitation using a miniature HTS floating coil having a diameter of 80 mm. The coil was fabricated using Bi-2223/Ag tapes of 12 m and excited by field cooling with liquid nitrogen. The magnetic levitation was examined using a real-time feedback control system with laser displacement gauges. Additionally, a persistent current switch (PCS) has been developed using Bi-2223/Ag tapes of 21 m, and a prototype HTS-PCS was tested in a cryostat. After construction of the floating coil and HTS-PCS for the Mini-RT device was completed, excitation tests were carried out in the cryostat and the basic properties up to the nominal operation condition were examined. (author)

La materia en condiciones extremas de densidad y temperatura

OpenAIRE

Morones Ibarra, José Rubén

2013-01-01

El estudio de las propiedades de la materia cuando se encuentra sometida a condiciones extremas de temperatura y presión ha llamado la atención de los físicos nucleares y de partículas elementales debido a la importancia que este tema tiene para conocer las condiciones iniciales del universo. En los primeros instantes del Gran Estallido (Big Bang) el universo era una región muy pequeña del espacio y por lo tanto su densidad y temperatura eran enormes. Para ente...

Ethylene evolution and endo-beta-mannanase activity during lettuce seed germination at high temperature Evolução de etileno e atividade da enzima endo-beta-mananase durante a germinação de sementes de alface sob altas temperaturas

Directory of Open Access Journals (Sweden)

Warley Marcos Nascimento

2004-04-01

Full Text Available High temperatures during lettuce seed imbibition can delay or completely inhibit germination and the endosperm layer appears to restrict the radicle protrusion. The role of endo-beta-mannanase during lettuce seed germination at 35°C and the influence of ethylene in endo-beta-mannanase regulation were investigated. Seeds of 'Dark Green Boston' (DGB and 'Everglades' (EVE were germinated in water, or 10 mmol L-1 of 1-aminocyclopropane-1-carboxylic acid (ACC, or 10 mmol L-1 of aminoethoxyvinylglycine (AVG, or 20 mmol L-1 of silver thiosulphate (STS. Seeds were also primed in polyethylene glycol (PEG, or PEG + ACC, PEG + AVG, or PEG + STS. Untreated seeds germinated 100% at 20°C. At 35°C, EVE seeds germinated 100%, whereas DGB seeds germinated only 33%. Seed priming or adding ACC during incubation increased germination at 35°C. Higher ethylene evolution was detected in EVE than in DGB during germination at 35°C. AVG did not inhibit seed germination of DGB at 35°C, but STS did. Higher endo-beta-mannanase activity was observed in EVE compared with DGB seeds. Providing ACC either during priming or during germination increased endo-beta-mannanase activity, whereas AVG and STS led to decreased or no activity. Ethylene may overcome the inhibitory effect of high temperature in thermosensitive lettuce seeds due to increased endo-beta-mannanase, possibly leading to weakening of the endosperm.Altas temperaturas durante a embebição das sementes de alface podem atrasar ou inibir a germinação e o endosperma parece ser o responsável na restrição da protrusão da radícula. O envolvimento da enzima endo-beta-mananase durante a germinação de sementes de alface a 35°C e a influência do etileno na regulagem desta enzima foram estudados. Sementes das cultivares Dark Green Boston (DGB e Everglades (EVE foram germinadas em água ou em soluções de 10 mmol L-1 de 1-aminociclopropano-1-ácido carboxilico (ACC, 10 mmol L-1 de amino-etoxi-vinil-glicina (AVG

Alta peab tasuma Kalevile mais / Kersti Saar

Index Scriptorium Estoniae

Saar, Kersti

2008-01-01

Indrek Rahumaa juhitav Alta Capital peab tasuma Oliver Kruudale Kalevi tütarfirmade eest 660 miljonit krooni hiljemalt 30. maiks. Vt. samas: Investorid teavad tehingu hinda ja lõplikku tähtaega. Diagramm: Kalevi turuväärtus jääb Alta müügihinnale alla

Development of multilayer coatings for mechanical applications

OpenAIRE

Portinha, Aníbal Jorge Fernandes

2012-01-01

Tese de Doutoramento em Ciências (Especialidade em Física) Este trabalho consiste essencialmente no desenvolvimento, produção e caracterização de revestimentos para aplicações mecânicas de alta temperatura. Desta forma desenvolveram-se novos revestimentos nanoestructurados, nanolaminados, multicamada e graduados à base de zirconia (ZrO2) parcial e totalmente estabilizada para protecção de componentes metálicos que operam a alta temperatura, tais como em turbinas a gás de ...

Electromechanical characterization of superconducting wires and tapes at 77 K

CERN Document Server

Bjoerstad, Roger

The strain dependency of the critical current in state-of-the-art cuprate high-temperature superconductors (HTS) has been characterized. A universal test machine (UTM) combined with a critical current measurement system has been used to characterize the mechanical and the superconducting properties of conductors immersed in an open liquid nitrogen dewar. A set-up has been developed in order to perform simultaneous measurements of the superconductor lattice parameter changes, critical current, as well as the stress and strain at 77 K in self-field in a high energy synchrotron beamline. The HTS tapes and wires studied were based on YBCO, Bi-2223 and Bi-2212. The YBCO tapes were produced by SuperPower and American Superconductors (AMSC). Two types of Bi-2223 tapes, HT and G, were produced by Sumitomo Electric Industries (SEI). The Bi-2212 wires were produced by Oxford Superconducting Technology (OST) using Nexans granulate precursor, before undergoing a specialized over pressure (OP) processing and heat treatmen...

The effects of temperature and oxygen availability on intracapsular development of Acanthina monodon (Gastropoda: Muricidae El efecto de la temperatura y la disponibilidad de oxígeno sobre el desarrollo intracapsular de Acanthina monodon (Gastropoda: Muricidae

Directory of Open Access Journals (Sweden)

MIRIAM FERNÁNDEZ

2006-06-01

experimentales de temperatura (7, 11, 15 y 19 °C y oxígeno (hipoxia: 50-60 % saturación de aire; normoxia; e hiperoxia: 150-160 %. Más embriones permanecieron en fases tempranas del desarrollo al final del experimento en hipoxia y a 19 °C. El número promedio de embriones desarrollados fue significativamente más bajo en hipoxia que bajo normoxia e hiperoxia, pero no fue influenciado por la temperatura. Sin embargo, la temperatura de incubación afectó otras variables de respuesta. Menores tamaños de los embriones y mayores niveles de asincronía al final del desarrollo fueron observados en las más altas temperaturas experimentales, lo que podría tener consecuencias negativas sobre la sobrevivencia posasentamiento. Las altas temperaturas también afectan el comportamiento y los costos asociados a la provisión de oxígeno a los embriones en braquiuros. Estas evidencias sugieren que agregar embriones en el océano, aun en condiciones óptimas de oxígeno, podría ser desfavorable a altas temperaturas. Los patrones espaciales de distribución de especies incubadoras tienden a apoyar esta predicción. Nuestro análisis también cobra relevancia en el escenario actual de aumento de la temperatura media de los océanos y de la proporción de zonas anóxicas

Desarrollo de intermetálicos TiAl mediante técnicas pulvimetalúrgicas convencionales y de alta densificación

Directory of Open Access Journals (Sweden)

Vicente Amigó-Borrás

2014-01-01

Full Text Available Cada día hay más demanda de materiales que ofrezcan altas temperaturas de servicio y bajo peso; pero su fabricación es compleja y costosa, particularmente la de las superaleaciones de base cobalto y la de las aleaciones de titanio; dentro de estas últimas, los intermetálicos TiAl y Ti3Al son ampliamente reconocidos para satisfacer las necesidades actuales; sin embargo, la colada y forja de estos intermetálicos, que tienen una mejor resistencia frente a la oxidación a elevadas temperaturas, resulta muy compleja, y es por lo que, partiendo de polvo prealeado, se busca obtener productos prácticamente acabados con un coste razonable. El presente trabajo analiza la influencia de las variables de procesado de polvos intermetálicos Ti48Al2Cr2Nb, mediante técnicas pulvimetalúrgicas convencionales y Spark Plasma Sintering (SPS, en su microestructura y en sus propiedades mecánicas. Se obtienen muestras a diferentes temperaturas de sinterización a partir de polvos obtenidos por atomización. La influencia en las propiedades mecánicas se observa mediante su microdureza y resistencia a la compresión, realizándose un seguimiento de la microestructura mediante microscopía óptica y electrónica de barrido.Las condiciones de procesado muestran un gran efecto en la microestructura obtenida, fundamentalmente en la formación de la fase α2, que acompaña las propiedades mecánicas finales. Sin embargo, es con el proceso de máxima densificación donde se obtienen las propiedadesadecuadas, lo cual hace pensar que es una alternativa clara a los procesos actuales de colada y deformación plástica.

Wssv y temperatura, inmunoestimulantes, vitaminas... ¿cómo se relaciona todo?

OpenAIRE

Rodriguez, Jenny; Echeverría, Fabrizio; Sonneholznher, Stanislaus; Molina, César; Gullian, Mariel

2001-01-01

WSSV y temperatura, inmunoestimulantes, vitaminas... ¿Cómo se relaciona todo? Los experimentos desarrollados a la fecha indican que a temperatura de 33°C disminuye tanto la prevalencia (porcentaje de animales positivos) como la intensidad de la infección en juveniles y en larvas (Boletín Septiembre 15).

ADVANTAGES AND THERMODYNAMIC LIMITATIONS OF THE EXPERIMENTAL SORPTION ISOSTERIC METHOD

Directory of Open Access Journals (Sweden)

FARID B. CORTÉS

2013-01-01

Full Text Available Una revisión de las ventajas y las limitaciones termodinámicas presentes en el método experimental sorción isostérica (SIM muestra que el SIM no garantiza una cantidad adsorbida constante. Las isósteras calculadas que consideran comportamiento de gas ideal muestran que en el SIM la masa de gas en el volumen muerto del sistema al incrementar la presión de equilibrio debido a los materiales desorbidos. El SIM es útil y efectivo para obtener datos termodinámicos de alta precisión para la sorción de gases en materiales micro y nanoporosos a bajas presiones y temperaturas. Por el contrario, cuando la presión y la temperatura son altas la desorción no es despreciable, por lo tanto el SIM no es aplicable. Los errores en los cálculos del calor isostérico usando SIM pueden ser reducidos usando procedimientos experimentales tradicionales como las isobaras e isotermas de adsorción para generar las isósteras a altas presiones y temperaturas. Como alternativa, correcciones por presión y temperatura, o un experimento que, después de cada incremento de temperatura permita a la dosis de gas compensar la masa desorbida, garantizaría una cantidad adsorbida constante y, por consiguiente, un comportamiento isostérico mediante medidas directas.

Temperatura e embalagem para abóbora minimamente processada Temperature and packaging of minimally processed pumpkin (Curcubita moschata

Directory of Open Access Journals (Sweden)

Ana Veruska Cruzda Silva

2009-06-01

Full Text Available O objetivo deste trabalho foi avaliar temperaturas de armazenamento e embalagens para abóbora minimamente processada. Pedaços de abóbora foram cortados em tamanho de 5 x 10 cm, embalados em bandejas de poliestireno recobertas com filme polivinilcloreto e em embalagem de polietileno de alta densidade a vácuo. O produto foi mantido a 5 e 10 °C por um período de 12 dias. A cada três dias avaliou-se o teor de sólidos solúveis, acidez total titulável, pH, vitamina C e coloração. Os resultados mostraram não haver diferenças significativas entre as duas temperaturas de refrigeração utilizadas na conservação da abóbora. Entretanto, a embalagem com filme PVC permitiu maior conservação dos atributos de qualidade da abóbora até o 9º dia, com exceção da cor, que sofreu menores alterações quando usada embalagem a vácuo.The present work aimed to evaluate the efficiency of different storage temperatures and packing materials for pumpkin fresh cuts. Pumpkin cuts of 5 x 10 cm were packed in polystyrene trays covered with polivynilchloride film or in vacuum high density polyethylene bags. The trays and bags were kept at 5 and 10 °C for 12 days. Soluble solids, total titratable acidity, pH, vitamin C, and color of pumpkin cuts were evaluated every 3 days. The different temperatures did not affect the storage of the pumpkins. However, packaging with PVC film allowed a longer conservation by keeping the pumpkin quality attributes up to the 9th day, except for the color which undergone minor alterations when stored within a vacuum pack.

Alterações oxidativas (cor e lipídios em presunto de peru tratado por Alta Pressão Hidrostática (APH

Directory of Open Access Journals (Sweden)

Simone Pereira Mathias

2010-12-01

Full Text Available A Alta Pressão Hidrostática (APH consiste em uma tecnologia inovadora de processamento de alimentos com utilização de pressões elevadas (100 a 900 MPa que possui vantagens em relação às tecnologias térmicas convencionais, pois mantém as características sensoriais do alimento próximas do original e garante segurança do ponto de vista microbiológico, por prolongado período de vida útil. No presente estudo, foi avaliada a aplicação de alta pressão a presunto de peru nos processos oxidativos, em particular na oxidação de lipídios e os efeitos na cor do produto, quando tratados a pressões de 200 a 400 MPa, por 5, 10 e 15 minutos em temperatura ambiente. Dos resultados obtidos, pode-se observar que não foram verificadas diferenças significativas (p > 0,05 entre amostras controle e pressurizada para o índice de TBA e índice de peróxido. Foi observado também alteração da cor decorrente de reações oxidativas aos 45 e 65 dias de armazenamento em amostras tratadas com pressões de 400 MPa a 5 e 15 minutos

Corrosion of bismuth-based superconductor wires by some atmospheric agents

International Nuclear Information System (INIS)

Ben Azzouz, F.; M'chirgui, A.; Ben Salem, M.; Yangui, B.; Lamine, C.; Nitsche, S.; Boulesteix, C.

2000-01-01

Superconducting wires (SWs) were previously prepared in our group by heat treatment of bismuth-based superconductor coatings on a metal core. This paper presents an analysis of the corrosion process by some atmospheric agents on the SWs. SWs with different concentrations of a (Bi, Pb)-2223 phase have been exposed to water vapour saturated air, to pure water vapour or to dry carbon dioxide. Each of these atmospheric agents was found to act differently on the SWs. However, all the studied corrosion processes present a high sensitivity to the concentration of the (Bi, Pb)-2223 phase. For a higher concentration of this phase, the SWs are less sensitive to atmospheric agents. (author)

The ALTA global positioning satellite based timing system

CERN Document Server

Brouwer, W; Caron, B; Hewlett, J C; Holm, L; Hamilton, A H; McDonald, W J; Pinfold, J L; Schaapman, J R; Soluk, R A; Wampler, L J

2002-01-01

The Alberta Large-area Time-coincidence Array (ALTA) experiment uses a number of scintillation detector systems to form a sparse very large area cosmic air-shower detection array. An important scientific goal of the ALTA collaboration is to search for coincidences in the ALTA array due to large area cosmic ray phenomena. A local cosmic ray event, determined by a coincidence of the triplet of cosmic ray detectors forming a local detector system, is time stamped with a temporal coordinate obtained from a GPS receiver. The readout of the data, the local coincidence and the GPS time stamp are all performed in the local readout crate. This time stamp, along with the local shower direction is used to search for coincidences within the large area array. Using two GPS receivers and duplicate sets of ALTA electronics the timing resolution of the GPS time difference between sites was estimated to be 16 ns.

Características sensoriais, físicas e químicas e aceitação de arroz irrigado ou de terras altas

Directory of Open Access Journals (Sweden)

Melissa Ferrari Pagnan

2015-10-01

Full Text Available Resumo:O objetivo deste trabalho foi caracterizar química, física e sensorialmente três genótipos de arroz polido de cultivo irrigado e cinco de terras altas. Determinaram-se: a composição centesimal, o amido, a amilose, a temperatura de gelatinização (Tg, a absorção de água ao cozimento, a cor, a textura instrumental, o perfil sensorial e a aceitação de atributos. A composição centesimal e o teor de amido variaram entre os genótipos. O 'Moti' e a linhagem N2583 foram classificados como cerosos, 'Douradão' apresentou amilose muito baixa, e os demais genótipos, amilose baixa. 'Irga 417', 'Moti' e AB101002 apresentaram Tg baixa; 'Douradão', alta; e os demais, intermediária. O 'Moti' e a linhagem N2583 crus apresentaram os maiores valores de L*; no entanto, após o cozimento, esses valores diminuíram e foram idênticos em todos os genótipos. 'Arroz-da-terra' apresentou maior a*, 'BRS Primavera' e N2583 apresentaram maior b*; e após o cozimento, houve redução desses valores. Na análise sensorial, destacaram-se 'AN Cambará', por pontos escuros e formato alongado; AB101002, 'Irga 417' e 'BRS Primavera', pela firmeza, cor branca e grãos soltos, que foram bem aceitos; e o 'Moti', por ser pegajoso, macio e com brilho, foi o menos aceito. Os atributos sensoriais do arroz são mais associados a características químicas, intrínsecas ao genótipo, do que à atribuição de plantio a terras altas ou irrigadas.

Crioterapia no pos-parto: tempo de aplicacao e mudancas na temperatura perineal

Directory of Open Access Journals (Sweden)

Adriana Amorim Francisco

2013-06-01

Full Text Available Estudo descritivo com dados de dois ensaios clínicos realizados em 2008 e 2009 em uma maternidade de uma instituição filantrópica da cidade de São Paulo. Teve como objetivo descrever a temperatura perineal após a aplicação de bolsa de gelo no pós-parto normal. Três grupos com 38 puérperas cada (n=114 receberam aplicação perineal de bolsa de gelo entre 2 e 48h após o parto. Os achados indicaram que com 10 min de crioterapia as médias da temperatura perineal atingiram de 13,3 a 15,3oC, com pequena redução de temperatura ao final de aplicações de 15 e 20 minutos (2,4 e 2,7o, respectivamente. Após resfriamento por 10 min., as mulheres referiram frio e alívio e, depois de 15 a 20 min., dormência e anestesia local. Conclui-se que 10 minutos de aplicação foram suficientes para reduzir a temperatura perineal aos níveis recomendados para analgesia (10-15oC.

Multiphase-Multifunctional Ceramic Coatings

Science.gov (United States)

2013-06-30

systems for high temperatura applications” “ Estudios de Ferroelasticidad en Sistemas Cerámicos Multifásicos para Aplicaciones en Alta Temperatura ...Ceramic Coatings Performing Organization names: Centro de Investigación y de Estudios Avanzados del Instituto Politécnico Nacional – Unidad Queretaro...materials, Cinvestav. Thesis: “Ferroelasticity studies in multiphase ceramic systems for high temperatura applications”. Her work mainly focused in the

The ALTA cosmic ray experiment electronics system

International Nuclear Information System (INIS)

Brouwer, W.; Burris, W.J.; Caron, B.; Hewlett, J.; Holm, L.; Hamilton, A.; McDonald, W.J.; Pinfold, J.L.; Price, P.; Schaapman, J.R.; Sibley, L.; Soluk, R.A.; Wampler, L.J.

2005-01-01

Understanding the origin and propagation of high-energy cosmic rays is a fundamental area of astroparticle physics with major unanswered questions. The study of cosmic rays with energy more than 10 14 eV, probed only by ground-based experiments, has been restricted by the low particle flux. The Alberta Large-area Time-coincidence Array (ALTA) uses a sparse array of cosmic ray detection stations located in high schools across a large geographical area to search for non-random high-energy cosmic ray phenomena. Custom-built ALTA electronics is based on a modular board design. Its function is to control the detectors at each ALTA site allowing precise measurements of event timing and energy in the local detectors as well as time synchronization of all of the sites in the array using the global positioning system

Temperaturas cardinales de desarrollo en la etapa siembra- emergencia de 11 pastos forrajeros

Directory of Open Access Journals (Sweden)

Noé Durán Puga

2011-01-01

Full Text Available Los objetivos del presente estudio fueron determinar las temperaturas cardinales de desarrollo (temperatura umbral mínima Tb, temperatura óptima To y temperatura umbral máxima Tu, e identificar un método que estime con precisión los requerimientos térmicos para la etapa siembra-emergencia (E de 11 pastos forrajeros. Ciento veinte (120 semillas de cada uno se sembraron en recipientes en condiciones controladas con un diseño experimental completamente al azar y tres repeticiones a temperaturas constantes de 15 hasta 46 ºC, en cámaras de ambiente controlado del Instituto Nacional de Investigaciones Forestales Agrícolas y Pecuarias (INIFAP en Guadalajara, Jalisco, México. Las temperaturas cardinales y requerimiento térmico se estimaron mediante el método bilineal (MB y el método curvilíneo (MC, se evaluó su ajuste mediante comparación directa con los valores de desarrollo observados en ambiente controlado y coeficiente de variación de la duración de E expresada en términos de unidades calor acumuladas (UCA. Los resultados mostraron que el MB fue mejor para estimar Tb y To, y el MC fue mejor para estimar Tu. Los valores de Tb, To, Tu y UCA, fueron, Lolium perenne 9, 31, 41, 80, Festuca arundinacea 10, 31, 41, 78, Hyparrhenia rufa 12, 32, 42, 62, Eragrostis curvula 13, 32, 47, 40, Chloris gayana 13, 31, 47, 40, Melinis minutiflora 13, 31, 43, 50, Pennisetum clandestinum 12, 32, 43, 65, Brachiaria mutica 14, 32, 43, 57, Andropogon gayanus 12, 37, 48, 66, Cynodon dactylon 14, 29, 44, 48, Pennicetum ciliare 13, 30, 42, 61.

TransAlta Corporation 1996 annual report : new directions, new opportunities

International Nuclear Information System (INIS)

Anon.

1997-01-01

TransAlta Corp. is an energy management company that operates through two subsidiaries: (1) TransAlta Utilities Corp. which owns and operates electricity generation, transmission and distribution assets in Alberta, and (2) TransAlta Energy Corp. which is in the business of electric and thermal energy supply, gas and electricity distribution, energy services and energy marketing in regions of Canada, New Zealand, Australia, Argentina and the United States. This report presents a summary of operations, and provides consolidated financial statements and common share information for 1996. During the year the corporation advanced three significant initiatives (1) operational effectiveness, as shown by impressive productivity increases, and major investments in three independent power projects, (2) improved strategic direction through a review of plans and options, resulting in a clearer, more focused vision of the future, and (3) realignment of the organizational structure by centralizing marketing and sales functions, and establishing a corporate business development group. Details of operational and financial results were provided for both subsidiaries, i. e. TransAlta Utilities and TransAlta Energy. Sales of electric energy for TransAlta Utilities amounted to 27.8 billion kWh; 4.6 billion kWh for TransAlta Energy. Return on equity was 11.4 per cent, down from 11.8 per cent in 1995. Net earnings per common share were $1.14 per share (including one-time items), the same as in 1995. tabs., figs

Synthesis, microstructure and properties of BiFeO3-based multiferroic materials: A review

Directory of Open Access Journals (Sweden)

Bernardo, M. S.

2014-02-01

Full Text Available BiFeO3-based materials are currently one of the most studied multiferroics due to their possible applications at room temperature. However, among the large number of published papers there is much controversy. For example, possibility of synthesizing a pure BiFeO3 phase is still source of discussion in literature. Not even the nature of the binary Bi2O3-Fe2O3 diagram has been clarified yet. The difficulty in controlling the formation of parasite phases reaches the consolidation step. Accordingly, the sintering conditions must be carefully determined both to get dense materials and to avoid bismuth ferrite decomposition. However, the precise conditions to attain dense bismuth ferrite materials are frequently contradictory among different works. As a consequence, the reported properties habitually result opposed and highly irreproducible hampering the preparation of BiFeO3 materials suitable for practical applications. In this context, the purpose of the present review is to summarize the main researches regarding BiFeO3 synthesis, microstructure and properties in order to provide an easier understanding of these materials.Los materiales basados en BiFeO3 son en la actualidad uno de los multiferroicos más estudiados debido a sus posibles aplicaciones a temperatura ambiente. Sin embargo, entre la multitud de trabajos publicados referentes a estos materiales existe mucha controversia. Por ejemplo, la posibilidad de sintetizar una fase BiFeO3 pura es aún objeto de discusión en la bibliografía y la naturaleza de los diagramas de fases del sistema Bi2O3-Fe2O3 aún no está clara. La dificultad para controlar las fases parásitas se extiende al proceso de consolidación por lo que las condiciones de sinterización deben ser cuidadosamente controladas para obtener materiales densos y al mismo tiempo evitar la descomposición de la ferrita. No obstante, las condiciones precisas para obtener materiales densos de BiFeO3 son frecuentemente

Finite Element Analysis of Patella Alta: A Patellofemoral Instability Model.

Science.gov (United States)

Watson, Nicole A; Duchman, Kyle R; Grosland, Nicole M; Bollier, Matthew J

2017-01-01

This study aims to provide biomechanical data on the effect of patella height in the setting of medial patellofemoral ligament (MPFL) reconstruction using finite element analysis. The study will also examine patellofemoral joint biomechanics using variable femoral insertion sites for MPFL reconstruction. A previously validated finite element knee model was modified to study patella alta and baja by translating the patella a given distance to achieve each patella height ratio. Additionally, the models were modified to study various femoral insertion sites of the MPFL (anatomic, anterior, proximal, and distal) for each patella height model, resulting in 32 unique scenarios available for investigation. In the setting of patella alta, the patellofemoral contact area decreased, resulting in a subsequent increase in maximum patellofemoral contact pressures as compared to the scenarios with normal patellar height. Additionally, patella alta resulted in decreased lateral restraining forces in the native knee scenario as well as following MPFL reconstruction. Changing femoral insertion sites had a variable effect on patellofemoral contact pressures; however, distal and anterior femoral tunnel malpositioning in the setting of patella alta resulted in grossly elevated maximum patellofemoral contact pressures as compared to other scenarios. Patella alta after MPFL reconstruction results in decreased lateral restraining forces and patellofemoral contact area and increased maximum patellofemoral contact pressures. When the femoral MPFL tunnel is malpositioned anteriorly or distally on the femur, the maximum patellofemoral contact pressures increase with severity of patella alta. When evaluating patients with patellofemoral instability, it is important to recognize patella alta as a potential aggravating factor. Failure to address patella alta in the setting of MPFL femoral tunnel malposition may result in even further increases in patellofemoral contact pressures, making it

Effects of doping in BSCCO superconductor system; Efeito da dopagem do sistema superconductor BSCCO com terras raras

Energy Technology Data Exchange (ETDEWEB)

Rodrigues, V.D.; Carvalho, C.L.; Souza, E.J. de; Torsoni, G.B.; Silva, M.J. da, E-mail: vivian_delmute@yahoo.com.b [UNESP, Ilha Solteira, SP (Brazil). Dept. de Fisica e Quimica

2010-07-01

There are several studies on doping in superconducting systems, due to their high TC. Actually, the search for high current densities permitting future application of these materials. In this work, the purpose was to synthesize and characterize the phase (Bi,Pb)-2223 pure and doped BSCCO superconducting system to study the influence of the dopant on its electrical properties and its TC. Doping was achieved by substituting La in the sites of Sr, with the stoichiometric formula Bi{sub 1,6}Pb{sub 0,4}Sr{sub 2-x}Re{sub x}Ca{sub 2}Cu{sub 3}O{sub 10+{delta}{delta}}, where x=0.5. Precursor solutions were prepared by Pechini method and heat treated between 800 deg C- 810 deg C. The samples were structurally characterized by X-ray diffraction and electrically by dc four-probe method. XRD analysis suggesting the formation of (Bi,Pb)-2212 and (Bi,Pb)-2223 phase in pure and doped samples, respectively. While the electrical measurements indicated a decrease in the superconducting temperature for the doped sample. (author)

Effects of high temperature on survival, symbiotic performance and genomic modifications of bean nodulating Rhizobium strains Sobrevivência, fixação de nitrogênio e modificações genéticas em estirpes de Rhizobium sp. efetivas na nodulação do feijoeiro, expostas à altas temperaturas

Directory of Open Access Journals (Sweden)

Patrícia P. Pinto

1998-10-01

Full Text Available High temperatures can affect the survival, establishment and symbiotic properties of Rhizobium strains. Bean nodulating Rhizobium strains are considered particularly sensitive because on this strains genetic recombinations and/or deletions occur frequently, thus compromising the use of these bacteria as inoculants. In this study R. tropici and R. leguminosarum bv. phaseoli strains isolated from Cerrado soils were exposed to thermal stress and the strains’ growth, survival and symbiotic relationships as well as alterations in their genotypic and phenotypic characteristics were analyzed. After successive thermal shocks at 45ºC for four hours, survival capacity appeared to be strain-specific, independent of thermo-tolerance and was more apparent in R. tropici strains. Certain R. leguminosarum bv. phaseoli strains had significant alterations in plant dry weight and DNA patterns obtained by AP-PCR method. R. tropici strains (with the exception of FJ2.21 were more stable than R. leguminosarum bv. phaseoli strains because no significant phenotypic alterations were observed following thermal treatments and they maintained their original genotypic pattern after inoculation in plants.Altas temperaturas podem afetar a sobrevivência, estabelecimento e as propriedades simbióticas em estirpes de Rhizobium. As estirpes capazes de nodular o feijoeiro têm sido consideradas particularmente sensíveis, porque nessas estirpes é comum a ocorrência de recombinações e/ou deleções genômicas comprometendo, muitas vezes, a sua utilização como inoculantes. Neste trabalho, procurou-se avaliar a capacidade de crescimento e sobrevivência em temperaturas elevadas de estirpes de Rhizobium efetivas na fixação de nitrogênio no feijoeiro isoladas dos cerrados, bem como avaliar suas características fenotípicas e genotípicas após choque térmico. A capacidade de sobrevivência à temperaturas elevadas, avaliada após choques térmicos sucessivos (45ºC por 4

Criatividade e altas habilidades/superdotação

Directory of Open Access Journals (Sweden)

Denise de Souza Fleith

2011-11-01

Full Text Available Identificar e estimular a criança com altas habilidades/superdotação tem se constituído em um desafio para educadores e psicólogos. Muitas concepções acerca do fenômeno das altas habilidades têm sido propostas por estudiosos desde o início do século XX. Uma das concepções mais conhecidas sobre o superdotado é de que seria aquele indivíduo que se sai bem nos testes de inteligência, ou que apresenta um desempenho intelectual superior. Entretanto, superdotação não pode ser considerada exclusivamente como sinônimo de QI alto. Concepções atuais sobre este fenômeno têm chamado a atenção para a importância de se considerar outros aspectos como influência do ambiente, sorte, autoconceito positivo, motivação e, especialmente, a criatividade. Dois importantes objetivos da educação do aluno com altas habilidades/superdotação são: (a desenvolver talentos e habilidades, auxiliando estes indivíduos a atualizarem seu potencial e se tornarem criativos, e (b habilitá-los a darem contribuições criativas à sociedade. O objetivo deste artigo é, portanto, discutir a importância da criatividade no desenvolvimento de altas habilidades/superdotação. Palavras-chave: Superdotação. Altas Habilidades. Criatividade. Inteligência.

Avaliação da influência da temperatura sobre o desenvolvimento de Aedes albopictus

Directory of Open Access Journals (Sweden)

Daniéla Cristina Calado

2002-04-01

Full Text Available OBJETIVO: Verificar a influência da temperatura sobre os estágios de desenvolvimento de Aedes albopictus sob condições de laboratório. MÉTODOS: Foi avaliado o período de desenvolvimento dos estágios de ovo, larva e pupa em quatro temperaturas constantes de 15ºC, 20ºC, 25ºC e 30ºC em câmaras climatizadas com umidade relativa do ar oscilando entre 70% e 85% e fotoperíodo de CE 12:12 horas. Pela análise de variância, foram testados os efeitos das quatro temperaturas constantes. RESULTADOS: O período de incubação dos ovos compreendeu 38,38; 19,09; 13,10; e 10,44 dias; o período larval dos indivíduos machos atingiu 30,13; 13,83; 7,36; e 5,57 dias; o período larval para fêmeas apresentou duração de 33,22; 15,00; 8,06; e 6,16 dias; o período pupal em machos compreendeu 8,01; 4,92; 2,40; e 1,76 dias, enquanto nas fêmeas foi de 8,15; 5,11; 2,60; e 1,88 dias sob as temperaturas de 15ºC, 20ºC, 25ºC e 30ºC, respectivamente. Em todos os estágios de desenvolvimento, foram encontradas diferenças significativas, entre as temperaturas avaliadas, em torno de 5% no tempo de desenvolvimento. O período de desenvolvimento foi inversamente relacionado à temperatura, com o período larval mais breve em machos que em fêmeas. Nas temperaturas de 20ºC a 30ºC, o desenvolvimento foi mais breve e com maior viabilidade que a 15ºC. CONCLUSÕES: Nas condições em que foram realizados os experimentos, a temperatura afetou de forma significativa e inversamente proporcional os estágios imaturos de Aedes albopictus. Esses resultados mostram que os estágios imaturos são mais suscetíveis durante os períodos de baixas temperaturas devido ao maior tempo necessário para completar o desenvolvimento, informação que pode ser utilizada em estratégias de controle.

Electronic Structure of the Bismuth Family of High Temperature Superconductors

Energy Technology Data Exchange (ETDEWEB)

Dunn, Lisa

2002-03-07

High temperature superconductivity remains the central intellectual problem in condensed matter physics fifteen years after its discovery. Angle resolved photoemission spectroscopy (ARPES) directly probes the electronic structure, and has played an important role in the field of high temperature superconductors. With the recent advances in sample growth and the photoemission technique, we are able to study the electronic structure in great detail, and address regimes that were previously inaccessible. This thesis work contains systematic photoemission studies of the electronic structure of the Bi-family of high temperature superconductors, which include the single-layer system (Bi2201), the bi-layer system (Bi2212), and the tri-layer system (Bi2223). We show that, unlike conventional BCS superconductors, phase coherence information emerges in the single particle excitation spectrum of high temperature superconductors as the superconducting peak in Bi2212. The universality and various properties of this superconducting peak are studied in various systems. We argue that the origin of the superconducting peak may provide the key to understanding the mechanism of High-Tc superconductors. In addition, we identified a new experimental energy scale in the bilayer material, the anisotropic intra-bilayer coupling energy. For a long time, it was predicted that this energy scale would cause bilayer band splitting. We observe this phenomenon, for the first time, in heavily overdoped Bi2212. This new observation requires the revision of the previous picture of the electronic excitation in the Brillouin zone boundary. As the first ARPES study of a trilayer system, various detailed electronic proper- ties of Bi2223 are examined. We show that, comparing with Bi2212, both superconducting gap and relative superconducting peak intensity become larger in Bi2223, however, the strength of the interlayer coupling within each unit cell is possibly weaker. These results suggest that the

INFLUÊNCIA DA TEMPERATURA NO DESEMPENHO DE BIODIGESTORES COM ESTERCO BOVINO

Directory of Open Access Journals (Sweden)

Larissa Rodrigues de Castro

1998-04-01

Full Text Available RESUMO A presente pesquisa trata do estudo de biodigestores de batelada mantidos a diferentes temperaturas, visando analisar os níveis mais favoráveis à produção de biogás e à degradação de sólidos totais e voláteis de esterco bovino. A temperatura mais adequada obtida em laboratório (31ºC foi aplicada em um biodigestor rural modelo indiano, com 10m3 de capacidade, a fim de se verificar seu desempenho.

Modelos de Ensuciamiento en Intercambiadores de Calor Tubulares en Sistemas indirectos en Procesos uHt en la Industria Láctea

OpenAIRE

Luis Gómez Orozco; Ana Ilva Capera Urrego

2016-01-01

La tecnología de ultra alta temperatura (UAT) se utiliza ampliamente en la industria de la leche para el tratamiento térmico, ofreciendo una alta eficiencia en cuanto a la destrucción de microorganismos esporu- lados. Sin embargo, dentro de este proceso se encontró que a temperaturas entre 75°C y 110°C, se llevan a cabo procesos de agregación y desnaturalización de proteínas y precipitación de sales minerales que forman una capa o costra de ensuciamiento en las paredes del tubo de calentamien...

Tolerance of corn lines seeds to high drying temperature

OpenAIRE

José, Solange Carvalho Barrios Roveri; Pinho, Édila Vilela de Resende Von; Pinho, Renzo Garcia Von; Silveira, César Martoreli da

2004-01-01

Cultivares tolerantes a altas temperaturas de secagem proporcionam redução no tempo de secagem, uma etapa crítica no sistema de produção de sementes de milho (Zea mays L.). Nesta pesquisa, foi avaliada a tolerância à alta temperatura de secagem de sementes de linhagens de milho, por meio de testes de germinação e vigor. As sementes foram colhidas manualmente em espigas com teor de água em torno de 35% e secas artificialmente à 45 C até atingirem 11% de teor de água. Em seguida, foram submetid...

Temperatura e umidade relativa na qualidade da tangerina "Montenegrina" armazenada Temperature and relative humidity during cold storage of 'Montenegrina' tangerine

Directory of Open Access Journals (Sweden)

Auri Brackmann

2008-04-01

Full Text Available O presente trabalho foi conduzido com o objetivo de avaliar o efeito da temperatura e da umidade relativa do ar (UR sobre a manutenção da qualidade de tangerinas durante o período de armazenamento refrigerado (AR. O delineamento experimental utilizado foi inteiramente casualizado, em esquema bifatorial, com oito repetições, contendo 15 frutos cada. Os tratamentos avaliados constituíram-se da combinação das temperaturas 2, 3 e 4°C, com UR do ar de 90 e 96%. Após oito e 12 semanas de armazenamento, mais três dias de exposição a 20°C, foram realizadas as seguintes análises: acidez total titulável (ATT, sólidos solúveis totais (SST, consistência dos frutos, incidência de podridões e suculência. De acordo com os resultados obtidos, os frutos armazenados a 3°C + UR do ar de 90% apresentaram ATT, SST e consistência mais elevada, após oito e 12 semanas de AR. A incidência de podridão foi significativamente superior nos tratamentos com alta UR do ar (96%. Injúrias provocadas pela baixa temperatura ocorreram em alguns frutos no tratamento a 2°C. Não se constatou diferença significativa na suculência entre os tratamentos em ambas as datas de avaliação. A temperatura de 3°C combinada com UR de 90% apresentou os melhores resultados na conservação de tangerinas "Montenegrina", que podem ser armazenadas por um período de até oito semanas.This research was conducted in order to evaluate the effect of temperature and relative humidity (RH on the quality of tangerines during cold storage. The experimental design was entirely randomized, in a bifatorial design with eight replications of 15 fruits. The treatments were the combination of three temperatures (2, 3 and 4oC and two RH levels (90 and 96%. Evaluations of quality were performed after 8 and 12 weeks of cold storage plus 3 days of shelf life at 20°C. The analyzed parameters were: total titratable acidity (TTA, total soluble solids (TSS, fruits consistency, rot

Overexpression of the NADP+-specific isocitrate dehydrogenase gene (icdA) in citric acid-producing Aspergillus niger WU-2223L.

Science.gov (United States)

Kobayashi, Keiichi; Hattori, Takasumi; Hayashi, Rie; Kirimura, Kohtaro

2014-01-01

In the tricarboxylic acid (TCA) cycle, NADP(+)-specific isocitrate dehydrogenase (NADP(+)-ICDH) catalyzes oxidative decarboxylation of isocitric acid to form α-ketoglutaric acid with NADP(+) as a cofactor. We constructed an NADP(+)-ICDH gene (icdA)-overexpressing strain (OPI-1) using Aspergillus niger WU-2223L as a host and examined the effects of increase in NADP(+)-ICDH activity on citric acid production. Under citric acid-producing conditions with glucose as the carbon source, the amounts of citric acid produced and glucose consumed by OPI-1 for the 12-d cultivation period decreased by 18.7 and 10.5%, respectively, compared with those by WU-2223L. These results indicate that the amount of citric acid produced by A. niger can be altered with the NADP(+)-ICDH activity. Therefore, NADP(+)-ICDH is an important regulator of citric acid production in the TCA cycle of A. niger. Thus, we propose that the icdA gene is a potentially valuable tool for modulating citric acid production by metabolic engineering.

Influencia del citoplasma sobre la expresión del centro blanco y temperatura de gelatinización en arroz (Oryza sativa. L.

Directory of Open Access Journals (Sweden)

Baena García Diosdado

1995-12-01

Full Text Available

La investigación se adelantó en el Centro Internacional de Agricultura Tropical (CIAT durante 1989-1991. No hubo influencia del citoplasma en la expresión del centro blanco y temperatura de gelatinización. El orden de dominancia El orden de dominancia de los progenitores para el carácter ausencia de centro blanco fue Colombia 1 > 1R5 = L6850 > IRAT8. El cultivo in vitro influyó sobre la expresión del centro blanco y la temperatura de gelatinización en los progenitores y posiblemente en las poblaciones segregantes. El medio ambiente influyó más sobre los progenitores LR5y L6850 (y sus progenies. La selección hacia centro blanco bajo parece no ser eficiente en generaciones tempranas, especialmente en el caso de L6850 e IRAT8, en contraste con la mayor eficiencia de la selección por temperatura de gelatinización (heredabilidad alta. Se encontró un alto índice de concordancia (79%, entre la escala 0 a 5 utilizada para calificación subjetiva de centro blanco y el área del grano afectada por centro blanco, (lectura hecha en esteroscopio con micrómetro.

A research work was undertaken at the Centro International de Agricultura Tropical (CIAT, during 1989-91. There was no maternal effect on the express ion of white center and gelatinization temperature but rather different degrees of dominance, the order of dominance was Colombia 1 > IR5 = L6850 > LRAT8; the in vitro culture influenced the express ion of white belly and the gelatinization temperature in the parents and possibly in their progenies; the influence of the environment was greater on IRAT8 and L6850 (and its progenies; selection for low white belly seemed to be not efficient in early generations; but selection for the desired gelatinization temperature is more efficient (high heritability. With the F3 samples, a subjective evaluation was carried out (zero: endosperm without white belly, and five: completely chalky, There was found a high index of concordance (79

Estudio fotométrico de estrellas tardías de alta luminosidad en 23 cúmulos abiertos

Science.gov (United States)

Clariá, J. J.; Piatti, A. E.; Osborn, W.

Se presentan resultados obtenidos en los Observatorios de Cerro Tololo, Kitt Peak, Lowell y Las Campanas, a partir de fotometría UBV y DDO de 54 estrellas tardías de alta luminosidad en 23 cúmulos abiertos. La aplicación de dos criterios fotométricos independientes permite asignar a cada estrella probabilidades de pertenencia a cada agregado. Se encuentra que 32 estrellas son muy probablemente miembros de los cúmulos, mientras que las restantes son objetos del campo. En todos los casos se determinan excesos de color E(B-V) a través de procedimientos fotométricos y espectroscópicos tradicionales. Recientes calibraciones del sistema DDO permiten, además, derivar tipos espectrales MK, temperaturas efectivas, y abundancias superficiales de la muestra examinada. Las metalicidades DDO derivadas se distribuyen entre valores típicos de cúmulos moderadamente pobres en metales ([Fe/H]~=-0.3) y moderadamente ricos ([Fe/H]~=0.2), en tanto que las masas calculadas para las gigantes rojas oscilan entre 1 y 4 masas solares, con una dispersión dentro de cada cúmulo menor que 1 Msolar.

O papel do professor junto ao aluno com Altas Habilidades

Directory of Open Access Journals (Sweden)

Andréia Jaqueline Devalle Rech

2012-03-01

Full Text Available .Quando se discute a Educação Especial é comum, num primeiro momento, lembrar do aluno que compõe o especial na Educação como aquele com deficiência mental, auditiva, visual ou física. No entanto, assim como essas crianças, também os alunos com altas habilidades necessitam de um atendimento especializado, pois ele também é um sujeito da Educação Especial. Nesse sentido, este artigo apresenta a definição de altas habilidades, baseada na teoria de um pesquisador norte-americano e, como foco principal algumas questões que envolvem o professor de forma mais direta com o aluno com altas habilidades em sala de aula. Entre elas estão: questões sobre a aprendizagem escolar desses alunos, bem como os fatores que fazem parte desse processo, estratégias de ensino e a importância da identificação dos alunos com altas habilidades.Palavras-chave: Educação Especial. Professor. Aluno com Altas Habilidades

Current status of high-T{sub c} wire

Energy Technology Data Exchange (ETDEWEB)

Vase, Per [Nordic Superconductor Technologies A/S, Priorparken 685, DK 2605 Broendby (Denmark); Fluekiger, Rene [Departement de Physique de la Matiere Condensee, Universite de Geneve (Switzerland); Leghissa, Martino [Siemens AG, Corporate Technology, Erlangen (Germany); Glowacki, Bartek [Department of Material Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom)

2000-07-01

This paper is the result of the work of a SCENET (The European Network for Superconductivity) material working group's efforts on giving values for present and future expected performance of high-temperature superconducting (HTS) wires and tapes. The purpose of the work is to give input to the design of HTS applications like power cables, motors, current leads, magnets, transformers and generators. The current status performance values are supposed to be used in the design of today's prototypes and the future values for the design of fully commercial HTS applications of the future. We focus on what is expected to be the relevant parameters for HTS application design. The most successful technique by far for making HTS tapes has been on the (Bi, Pb){sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} (Bi-2223) material by the powder-in-tube (PIT) technique and this paper therefore focuses on giving the current status and expected future performance for Bi-2223 tapes. (author)

Transport critical current measurement apparatus using liquid nitrogen cooled high-T(c) superconducting magnet with variable temperature insert.

Science.gov (United States)

Nishijima, G; Kitaguchi, H; Tshuchiya, Y; Nishimura, T; Kato, T

2013-01-01

We have developed an apparatus to investigate transport critical current (I(c)) as a function of magnetic field and temperature using only liquid nitrogen. The apparatus consists of a (Bi,Pb)(2)Sr(2)Ca(2)Cu(3)O(10) (Bi-2223) superconducting magnet, an outer dewar, and a variable temperature insert (VTI). The magnet, which is operated in depressurized liquid nitrogen, generates magnetic field up to 1.26 T. The sample is also immersed in liquid nitrogen. The pressure in the VTI is controlled from 0.02 to 0.3 MPa, which corresponds to temperature ranging from 66 to 88 K. We have confirmed the long-term stable operation of the Bi-2223 magnet at 1 T. The temperature stability of the sample at high transport current was also demonstrated. The apparatus provides easy-operating I(c) measurement environment for a high-T(c) superconductor up to 500 A in magnetic fields up to 1 T and in temperatures ranging from 66 to 88 K.

Monitoreo de parametros físico-químicos en la cuenca alta del río Bogotá

Directory of Open Access Journals (Sweden)

Julia Sierra

2002-01-01

Full Text Available La Universidad Militar "Nueva Granada" en su constante interés por el desarrollo de nuevas técnicas que permitan la preservación del medio ambiente, inició en el año 2000 la investigación "IDENTIFICACIÓYNPRUEBADEBIOINDICADORESy RECUPERADORES PARALA DESCONTAMINACIÓN DEL RÍO BOGOTÁ". En la primera fase de este estudio se hace un diagnóstico de la situación actual de la cuenca alta del Río Bogotá, a través de los proyectos de grado presentados por los estudiantes de la Universidad y dirigidos por un grupo de profesores. Se realizó una investigación como Tesis de Grado para optar al título de Ingeniero Civil,donde se analiza el comportamiento de los pará-. metros fisico-químicos en la cuenca alta del Río Bogotá; estos parámetros son de gran importancia ya que establecen las modificaciones que sufre una corriente superficial, como consecuencia de los diferentes usos del agua (causados por actividades industriales, domésticas, recreativas y de transporte. El título del trabajo de grado es "MONITOREODE PARÁMETROSFISICO-QUÍMICOS,EN LA CUENCAALTA DEL RÍO BOGOTÁ". Los aspectos fisicos que se tienen en cuenta en este trabajo son: turbiedad, temperatura y conductividad, y como aspectos químicos oxígeno disuelto, demanda bioquímica de oxígeno (DBO, demanda química de oxígeno (DQO, pH, alcalinidad total, acidez, dureza, cIoruros, amonio, nitritos, nitratos, fosfatos altos y bajos, sulfatos, cromo, cobre y cloro total.

Effects of Ti addition on LFZ Bi-2212 thin rods

Directory of Open Access Journals (Sweden)

Angurel, L. A.

2003-06-01

Full Text Available In order to reproduce previous results in Bi-2212 single crystals, the effects associated with the addition of Ti to the precursors of Laser Floating Zone textured Bi-2212 thin rods have been analyzed. It has been found that Ti induces a great number of nucleation centers in the molten zone and, in consequence, it reduces the grain size one order of magnitude. In addition, using the same growth conditions, the texture of the sample is strongly degraded. These microstructural changes strongly affect the superconducting properties showing that Ti addition destroys the network of low angle grain boundaries that are responsible for the high critical currents in these materials.

Se ha analizado el efecto de la introducción de Ti en precursores de Bi-2212 para ser texturados mediante láser a través del método de zona flotante, todo ello debido a los resultados esperanzadores obtenidos en monocristales. Se ha encontrado que el Ti introduce un gran número de centros de nucleación en la zona fundida, por lo que se reducen las dimensiones de los granos en un orden de magnitud aproximadamente. Por otra parte, y utilizando las mismas condiciones de crecimiento, se observa que la textura de la muestra se degrada severamente, Estos cambios microestructurales afectan en gran medida a las propiedades superconductoras, demostrándose que la introducción de Ti destruye la red de fronteras de grano de bajo ángulo, que son las responsables en estos materiales de las altas corrientes criticas.

Elaboración y posterior tratamiento del hormigón a bajas temperaturas

Directory of Open Access Journals (Sweden)

Meyer, A.

1962-09-01

Full Text Available Not availableEl hormigonado en ambiente frío con heladas requiere un especial cuidado y un control mejor que en el caso de temperaturas normales. En la obra cerrada de invierno, los diferentes elementos o el total de la obra y la preparación del hormigón se efectúan con calefacción y protección. Esto, generalmente, sólo se hace para temperaturas exteriores muy bajas. Las instalaciones especiales en una obra crean un mayor gasto y, en consecuencia, solamente resultan rentables en obras especialmente importantes. En la obra cerrada de invierno, el hormigón se elabora a temperaturas normales, condiciones que se mantienen durante el tratamiento posterior. En este caso, no aparece nada especial al hormigonar bajo estas condiciones.

Soil water availability regulates soil respiration temperature dependence in Mediterranean forests

OpenAIRE

Chang, Chao-Ting

2017-01-01

[spa] Las variaciones de la respiración del ecosistema y del suelo son principalmente impulsadas por la temperatura y la precipitación, pero la importancia de la temperatura y la precipitación puede variar a lo largo del tiempo y el espacio. En las escalas temporales diurnas a anuales, la respiración del ecosistema y del suelo generalmente aumenta con la temperatura media anual, pero se ha demostrado que la humedad del suelo muy baja o muy alta disminuye la respuesta a la temperatura de la ...

TransAlta 2003 annual report

International Nuclear Information System (INIS)

2004-01-01

This annual report presents financial information from TransAlta Corp., along with a review of its operations throughout 2003 and a summary of the how the electric utility has performed in terms of power generation, independent power producers, transmission and energy marketing. TransAlta is one of the largest non-regulated power generation and wholesale marketing companies in Canada. It's assets include coal-fired, gas-fired, hydro and renewable generation facilities in Canada, the United States, Mexico and Australia. Reported earnings in 2003 were $1.26 per share compared to $1.17 in 2002. The strong first quarter was followed by harsh market conditions, low water levels which affected hydro production, and pricing restrictions in Ontario that reduced contribution from the Sarnia plant. This report outlines the utility's progress in increasing revenue and producing more power. In 2003, unplanned outages were reduced by 7 per cent and injury frequency rate was reduced by 27 per cent. The installation of 114 wind turbines in Fort Macleod, Alberta, increased TransAlta's renewable energy capacity to 3.7 per cent in 2003. The wind farm produces 75 MW of electricity, enough to power more than 32,500 homes annually. This report summarized the company's energy resource activities and presented an operations review as well as consolidated financial statements and common share information. This included the utility's assets, liabilities, revenues, expenses and cash flows. Revenue and expenditure statements were summarized by source. refs., tabs., figs

Embarcaciones de alta velocidad

OpenAIRE

Rodrigo de Larrucea, Jaime

2008-01-01

revolución tecnológica, con el desarrollo de nuevos tipos de buques de diseños cada vez más específicos y adaptados a su navegación y función. Sin duda una de las más espectaculares innovaciones es la de los buques de alta velocidad.

Bienestar psicológico en personas con alta capacidad intelectual

Directory of Open Access Journals (Sweden)

Pedro Ramiro Olivier

2016-12-01

Full Text Available El bienestar psicológico en las personas de alta capacidad intelectual ha sido motivo de controversia en la literatura especializada. En ocasiones se ha considerado que estas personas son más proclives a un desajuste psicológico, mientras que otras veces los resultados han sido poco concluyentes. En el presente trabajo se ha estudiado el bienestar psicológico en personas de altas capacidades intelectuales, administrando la Escala de Bienestar Psicológico a 28 participantes de edades comprendidas entre los 22 y 34 años de edad. Fueron divididos en 2 grupos, uno de altas capacidades y otro de inteligencia estándar. El grupo de altas capacidades había sido identificado como tal 25 años atrás, cuando tenían una edad comprendida entre los 5 y 13 años, utilizando el modelo de los 3 anillos de Renzulli. Los resultados indicaron la inexistencia de diferencias significativas entre los participantes de altas capacidades e inteligencia estándar en las diferentes subescalas de bienestar personal, a excepción de la subescala de bienestar material.

Niche conservatism of Eulophia alta, a trans-Atlantic orchid species

Directory of Open Access Journals (Sweden)

Marta Kolanowska

2014-03-01

Full Text Available The genus Eulophia embraces over 230 species distributed through the tropical and subtropical Africa, Asia, Australia and the Americas. In Neotropics it is represented by a sole species – E. alta. The aim of the presented study was to evaluate the difference between ecological niches occupied by American and African populations of this species based on the ecological niche modeling. The similarity between the glacial and present niches occupied by E. alta was calculated and the factors limiting the species occurrence were identified. Areas of seasonal tropical forest, tropical savanna and woodland served as refugia for the studied species during last glacial maximum and they were more widespread in Neotropics than in Africa. No significant niche shift after last glacial maximum was observed. The distribution of E. alta in its whole range is restricted mainly by temperature seasonality. The differences in the niches occupied by African and Neotropical populations of E. alta suggest preglacial disjunction of the species range and independent adaptation of both groups. Despite the significant range disjunction of E. alta the species is characterized by relatively high degree of niche conservatism.

Atividade antioxidante das folhas de espinheira-santa - Maytenus ilicifolia Mart. ex Reiss., secas em diferentes temperaturas

Directory of Open Access Journals (Sweden)

Myrian Lane Soares Negri

Full Text Available Maytenus ilicifolia Mart. ex Reiss, a espinheira-santa verdadeira, é largamente utilizada para tratamento de gastrites e úlceras estomacais. O seu valor terapêutico é atribuído principalmente aos polifenóis (flavonóides e taninos e triterpenos. Os polifenóis são bastante estudados e estão relacionados à atividade antioxidante exercida pela planta. Existem vários métodos para avaliar a atividade antioxidante, a qual pode ser medida a capacidade antioxidante total utilizando o método de formação do complexo fosfomolibdênio e a atividade antioxidante em relação à redução de um radical, utilizando-se o DPPH (2,2-difenil-1-picrilhidrazila. A atividade antioxidante das folhas de espinheira-santa seca em diferentes temperaturas foi avaliada, visando verificar a possível influência das temperaturas de secagens e seu poder antioxidante. Foram utilizadas cinco temperaturas (40, 50, 60, 70 e 80 ºC e uma temperatura de secagem de rotina, de um produtor/beneficiador de plantas medicinais. As menores temperaturas apresentaram as maiores atividades antioxidantes.

Relação entre a temperatura e o molhamento foliar no monocíclo da Sigatoka-negra

Directory of Open Access Journals (Sweden)

Cleilson do Nascimento Uchôa

2012-06-01

Full Text Available A influência da temperatura (21, 24, 27 e 30 °C e da duração do tempo de molhamento foliar (0, 12, 24, 48 e 72 horas na penetração do agente causal da Sigatoka-negra (Mycosphaerella fijiensis foi quantificada em ambiente controlado. A área abaixo da curva do progresso da doença (AACPD e a incidência foram influenciadas pela temperatura e pela duração do tempo de molhamento foliar. Foram constatadas diferenças significativas (P=0,05 nos valores da AACPD para as diferentes temperaturas, bem como verificada a interação significativa (P=0,05 entre temperaturas e o molhamento foliar. Em todas as temperaturas foi possível a observação de sintomas, entretanto, a maior AACPD foi observada em folhas inoculadas que permaneceram na temperatura de 24 e 27°C, a partir de 48 horas de molhamento foliar. Nas temperaturas de 21ºC e 30°C a incidência de Sigatoka-negra foi menor. O período de molhamento foliar mínimo para o progresso da doença foi de 24 horas. Não foram observados sintomas de Sigatoka-negra em folhas inoculados com o molhamento foliar de 0 hora e 12 horas em todas as temperaturas. As folhas assintomáticas, após 5 dias em câmara úmida apresentavam sintomas característicos de Sigatoka-negra, demonstrando que os conídios inoculados nas folhas permaneceram viáveis por um período na ausência de água livre na folha.

Fulltext PDF

Indian Academy of Sciences (India)

Electrical resistivity of NaPb compound-forming liquid alloy using ab initio pseudopotentials ... Ultrasonic studies of aluminium-substituted Bi(Pb)-2223 superconduc- tors. M B Solunke, P U .... electrochemical studies for lithium secondary cells.

Effect of pelletization pressure on structural properties and critical current hysteresis of ceramic superconducting Bi sub 1 sub . sub 7 Pb sub 0 sub . sub 3 Sr sub 2 Ca sub 2 Cu sub 3 O sub y

CERN Document Server

Tepe, M; Abukay, D

2003-01-01

The effect of pelletization pressures on structural properties and critical current hysteresis of Bi sub 1 sub . sub 7 Pb sub 0 sub . sub 3 Sr sub 2 Ca sub 2 Cu sub 3 O sub y samples was investigated. The samples used in this study were prepared by classical solid-state reaction at the pressures from 100 up to 500 MPa. The obtained samples were characterized by resistance vs. temperature, (R-T), critical current density vs. applied magnetic field, (J sub c -H), material density vs. pressure, (rho-P), XRD, SEM, and EDAX. The results of this study showed that the quality of electrical and structural properties of Bi-2223 bulk superconductors strongly depends on the pelletization pressure. Pressing of bulk samples at 400 MPa produces textured grain alignment and associates microstructural modifications in order to enhance flux pinning and thus increases current carrying capacities. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Efecto de la temperatura de incubación sobre algunos aspectos de la ontogenia de Phrynops hilarii (Testudines: Chelidae

Directory of Open Access Journals (Sweden)

Piña, Carlos I.

2003-05-01

Full Text Available Nuestro objetivo es establecer los efectos de la temperatura de incubación sobre diferentes aspectos de la ontogenia y la supervivencia de crías de P. hilarii. En el presente trabajo respondemos las siguientes preguntas: 1 ¿afecta la temperatura de incubación al período de incubación de P. hilarii?; 2 ¿cuál es la menor temperatura a la cual existe desarrollo embrionario de P. hilarii?; 3 ¿varía el éxito de eclosión de P. hilarii en relación a la temperatura a la cual se incuban los huevos?; 4 ¿está la supervivencia de P. hilarii hasta el año de edad relacionada a la temperatura de incubación?

Método para Medir Indirectamente la Velocidad de Fase en Sensores Surface Acoustic Wave

OpenAIRE

Leonardo Andrés Pérez; Carlos Alberto Vera

2015-01-01

El sensor de temperatura Surface Acoustic Wave (SAW) ofrece amplias posibilidades para ser utilizado en ambientes hostiles. En teoría, las mediciones del SAW se pueden leer inalámbricamente sin integrar circuitos electrónicos en su estructura, permitiendo funcionalidades en mediciones a muy altas temperaturas. La literatura reporta que las variaciones de temperatura del SAW ocasionan corrimientos en su frecuencia de sincronismo, efecto que se atribuye a la sensibilidad térmica de la velocidad...

Cócs. Hallmark of the Terra Alta

Directory of Open Access Journals (Sweden)

Maria Del Loreto Meix

2004-04-01

Full Text Available This article looks at the traditional cake making in the Terra Alta (Catalonien area linked to festivities, and in particular the pastries usually made. In this area the pastries are known as cócs, a word common to Terra Alta and the neighbouring districts of Ribera d'Ebre and the Priorat. Locally produced mistelle, sweet or rancid wine is served with the pastries. Nowadays, the bakeries and cake makers in the area's towns and villages also produce traditionally crafted products, that used only to be homemade.The article, resulting from the final degree project produced by the author for her Humanities degree at the UOC, offers a privileged look at the richness of the Terra Alta in terms of its gastronomic history, customs and its high regard for its cakes. The author, who has previous experience in the field, places the specific aspects of Terra Alta cake making in the context of the Mediterranean cultures with common roots dating back to the ancient and medieval worlds and which still have an easily identifiable "family feel", whilst looking, from an ethnographic point of view, at what she calls the "world of wheat" in the area, (the dough for bread, the craft of the baker, the ovens and other tools, and the associated traditions, among other things. In short, she rescues a living part of the local day-to-day activities and places it under the microscope of food history, whilst providing information that may well be of interest for study from other points of view.

Incidencia de las plazas urbanas sobre el comportamiento térmico del entorno en alta densidad edilicia. El caso de la ciudad de Mendoza, Argentina.

Directory of Open Access Journals (Sweden)

susana Stocco

2018-05-01

Full Text Available Las plazas concebidas bajo el concepto de “plaza jardín” -modelo dominante en las ciudades de Latinoamérica- generan efectos microclimáticos a escala urbana y edilicia dado que actúan como fuente de enfriamiento nocturno. En contextos de baja y media densidad, dicho efecto está asociado fundamentalmente al diseño de la plaza: núcleo central predominantemente semi-sellado alrededor del cual se distribuyen áreas verdes a modo de bosques y prados. Sin embargo, en el caso de la ciudad de Mendoza-Argentina, la tendencia a la redensificación del tejido urbano, como estrategia de control del crecimiento urbano, limita los beneficios que proporcionan las configuraciones actuales de plazas. Es por ello que este trabajo evalúa el impacto de incrementar la dimensión de la plaza en el comportamiento térmico de la misma y su influencia sobre el microclima del entorno mediato, como alternativa para potenciar sus beneficios en áreas urbanas de alta densidad. Con tal fin, se seleccionaron tres casos de estudio, dos de ellos de una superficie equivalente a una manzana urbana –10000m2–, emplazados en entornos de media y alta densidad, y un caso de mayor superficie -40000m2-, inserto en un contexto de alta densidad. Tales casos fueron monitoreados térmicamente en la estación verano, durante un periodo de 21 días, mediante el uso de microadquisidores de datos del tipo HOBO H08-003-02. Se caracterizaron las condiciones radiativas a partir de la determinación del factor de visión de cielo (SVF. Los resultados obtenidos muestran que, al incrementar las dimensiones de la “plaza jardín”, sus diferentes estructuras -núcleo central, bosque, prado- presentan menores temperaturas respecto a su entorno durante todo el día. En consecuencia, constituye una estrategia eficiente para mejorar las prestaciones del espacio abierto respecto a sus efectos microclimáticos en entornos urbanos de alta densidad. Si bien dicha

Bi-Force

DEFF Research Database (Denmark)

Sun, Peng; Speicher, Nora K; Röttger, Richard

2014-01-01

of pairwise similarities. We first evaluated the power of Bi-Force to solve dedicated bicluster editing problems by comparing Bi-Force with two existing algorithms in the BiCluE software package. We then followed a biclustering evaluation protocol in a recent review paper from Eren et al. (2013) (A...... comparative analysis of biclustering algorithms for gene expressiondata. Brief. Bioinform., 14:279-292.) and compared Bi-Force against eight existing tools: FABIA, QUBIC, Cheng and Church, Plaid, BiMax, Spectral, xMOTIFs and ISA. To this end, a suite of synthetic datasets as well as nine large gene expression...

Perfil altitudinal de la temperatura media del aire en Colombia

Directory of Open Access Journals (Sweden)

Eslava Jesus

1992-10-01

Full Text Available

Se establecen ecuaciones que relacionan la temperatura media anual del aire en

Colombia con la altitud. Por medio de ellas se posibilita estimar los valores de esa temperatura en cualquier lugar, con el requisito de conocer únicamente el dato de su altitud y ubicación regional; también se determinan los gradientes altitudinales que, a su vez, posibilitan conocer cualquier otro dato de temperatura del aire,  conociendo los datos de otro sitio o estación base. Las ecuaciones muestran que los valores a nivel del mar y la variación altitudinal de la temperatura del aire en Colombia no son únicos, sino que cambian según las condiciones físicas de cada región o subregión y se diferencias sustancialmente de los valores propuestos con anterioridad por otros autores.

Equations that establish relations between annual average temperature and altitude are defined for Colombia. These equations allow to estimate temperature values at any place, just by knowing altitude and regional location data. It is also possible to determine altitudinal gradients, which in turn allows to know the temperature of a given place, from the data for a base. The defined equations show that temperature is not a unique function of altitudinal changes, but it also depends on specific physical conditions for each region or subregion.

Avaliação do sombreamento natural do flamboyant (Delonix regia na temperatura de um ambiente construído

Directory of Open Access Journals (Sweden)

Mário Carlos Rodrigues Ayres

2011-05-01

Full Text Available Avaliar o sombreamento de uma espécie arbórea e seus efeitos na temperatura de um ambiente construído a partir das medições de temperatura de globo, temperatura do ar, umidade relativa foi o objetivo deste trabalho. Avaliou-se o sombreamento produzido pela espécie arbórea flamboyant (Delonix regia quanto a atenuação da temperatura no interior de dois módulos de edificações. O local de realização da pesquisa foi a Embrapa agropecuária oeste (CPAO no município de Dourados. Os dados foram coletados no interior de dois módulos de edificações sem vedação lateral, construídos em estrutura de madeira e cobertos com telhas de fibrocimento, sendo um localizado à sombra da árvore e outro ao sol.  Em cada modulo foram colocados um termômetro de globo negro e um psicrômetro e no exterior um anemômetro para registro da velocidade do vento. A partir dos dados coletados, foram calculadas as porcentagens de atenuação da temperatura do ar, umidade relativa e temperatura de globo negro para cada um dos módulos. Com os resultados obtidos e relacionados os módulos a sombra da árvore com o módulo ao sol foi encontrada uma atenuação da temperatura de globo negro de 3,46°C e temperatura do ar de 1,26°C com porcentagem de 9,62% e 3,96%, respectivamente.

PROTECCIÓN CONTRA LA CORROSIÓN EN SALES FUNDIDAS DE UN ACERO HOT ROLLED, EN EL RANGO DE TEMPERATURAS DE 400 ºC-600 ºC, RECUBIERTO POR ROCIADO TÉRMICO CON ACERO INOXIDABLE 312

Directory of Open Access Journals (Sweden)

JOSE LUDDEY MARULANDA

2009-01-01

Full Text Available Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono tipo hot rolled, rociado térmicamente con una aleación de acero inoxidable tipo 312, con el equipo Rototec, en una mezcla de sal 20% Na2SO4 - 80% V2O5, entre 400ºC - 600ºC, durante tiempos de 1-7-22 horas. Los resultados mostraron una moderada protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento a 600ºC. Se concluyó que la velocidad de corrosión aumenta con la temperatura y disminuye con el tiempo de exposición.

Germinação de sementes de plantas medicinais lenhosas

Directory of Open Access Journals (Sweden)

Rosa Shirley G.T.da

2001-01-01

Full Text Available A germinação de sementes de Aloysia gratissima, Bauhinia forficata; Casearia sylvestris, Dodonea viscosa, Psychotria leiocarpa e Sida rhombifolia foi verificada usando-se agar a 1% em placas de petri ou areia como substrato. Foi testada a germinação em temperaturas constantes de 20, 25, 30 e 35°C na luz ou no escuro, além de 10 e 15°C somente na ausência de luz. Foram também usadas temperaturas diárias alternantes de 10-20°C; 15-25°C, 20-30°C e 25-35°C sendo por 9 horas na temperatura mais alta na luz, com intensidade de radiação entre 40 e 60 µmol.m-2.s-1. Apenas A. gratissima mostrou-se fotoblástica positiva, porém respondendo melhor à germinação com alternância de temperaturas. Em C. sylvestris e P. leiocarpa em temperaturas constantes só ocorreu germinação a 20 ou 25°C. Sementes de B. forficata germinaram acima de 80% entre 15 e 30°C constantes ou quando uma das temperaturas do par alternante estivesse entre estas duas temperaturas. D. viscosa, após escarificação das sementes, mostrou ampla faixa de germinação em diferentes temperaturas ou regime lúmico. S. rhombifolia germinou em taxas mais altas quando a temperatura constante foi 35°C ou quando, na alternância, esta temperatura estava presente. Nos tratamentos onde houve mais germinação, o ótimo situou-se em 44% para A. gratissima e 97% em B. forficata. Em se tratando de espécies nativas sem melhoramento ou seleção de matrizes, estes índices são bastante aceitáveis.

Tolerância a baixas temperaturas de cultivares de abacate (Persea americana Mill.

Directory of Open Access Journals (Sweden)

Soares Nilberto Bernardo

2002-01-01

Full Text Available Em experimento realizado no Núcleo de Agronomia do Sudoeste/IAC, em Capão Bonito (SP, observou-se o comportamento de 13 cultivares de abacate com seis anos de idade: Geada, Pollock e Simmonds (raça antilhana; Antoniolli, Breda, Campinas, Ermor, Jumbo, Margarida, Ouro verde, Reis e Solano (híbridos de antilhana x guatemalense e Fuerte (híbrido de mexicana x guatemalense em relação às baixas temperaturas. As temperaturas do ar registradas no posto meteorológico do local foram: -2,8degreesC; -0,4degreesC; -0,2degreesC e -1,8degreesC, respectivamente, nos dias 17; 18; 20 e 21 de julho de 2000. A cultivar Fuerte mostrou-se mais tolerante às baixas temperaturas, não apresentando injúrias nas plantas nem queda de frutos; as cultivares híbridas de antilhana x guatemalense apresentaram diferenças de tolerância ao frio; enquanto as antilhanas foram severamente injuriadas.

CARACTERIZACION DE GENES DESHIDRINA EN EUCALYPTUS GLOBULUS CUYA EXPRESION ES INDUCIDA POR LA ACLIMATACION A BAJA TEMPERATURA

OpenAIRE

FERNANDEZ REYES, MARTA ALEJANDRA

2011-01-01

Eucalyptus globulus es una especie importante para la producción de pulpa de madera en Chile, sin embargo presenta una gran sensibilidad a temperaturas de congelamiento. Durante los últimos años, muchos estudios han enfocado sus esfuerzos en dilucidar los mecanismos que regulan la respuesta de las plantas a baja temperatura, mediante el análisis de la expresión génica. En el presente trabajo se estudia la expresión de genes deshidrina durante el proceso de aclimatación a baja temperatura y...

CARACTERIZACION DE GENES DESHIDRINA EN EUCALYPTUS GLOBULUS CUYA EXPRESION ES INDUCIDA POR LA ACLIMATACION A BAJA TEMPERATURA

OpenAIRE

FERNANDEZ REYES ; MARTA ALEJANDRA; FERNANDEZ REYES ; MARTA ALEJANDRA

2011-01-01

Eucalyptus globulus es una especie importante para la producción de pulpa de madera en Chile, sin embargo presenta una gran sensibilidad a temperaturas de congelamiento. Durante los últimos años, muchos estudios han enfocado sus esfuerzos en dilucidar los mecanismos que regulan la respuesta de las plantas a baja temperatura, mediante el análisis de la expresión génica. En el presente trabajo se estudia la expresión de genes deshidrina durante el proceso de aclimatación a baja temperatura y la...

Temas de Física para Ingeniería: Temperatura y propagación del calor

OpenAIRE

Beléndez Vázquez, Augusto

1992-01-01

Acústica, fluidos y termodinámica: "Temperatura y propagación del calor". Introducción. Descripciones macroscópica y microscópica de un sistema. Equilibrio térmico y principio cero de la termodinámica. Termómetros y escala de temperaturas del gas ideal. Dilatación térmica. Propagación del calor.

Bi-induced band gap reduction in epitaxial InSbBi alloys

Energy Technology Data Exchange (ETDEWEB)

Rajpalke, M. K.; Linhart, W. M.; Birkett, M.; Alaria, J.; Veal, T. D., E-mail: T.Veal@liverpool.ac.uk [Stephenson Institute for Renewable Energy and Department of Physics, School of Physical Sciences, University of Liverpool, Liverpool L69 7ZF (United Kingdom); Yu, K. M. [Materials Sciences Division, Lawrence Berkeley National Laboratory, 1 Cyclotron Road, Berkeley, California 94720 (United States); Bomphrey, J. J.; Jones, T. S.; Ashwin, M. J., E-mail: M.J.Ashwin@warwick.ac.uk [Department of Chemistry, University of Warwick, Coventry CV4 7AL (United Kingdom); Sallis, S.; Piper, L. F. J. [Materials Science and Engineering, Binghamton University, Binghamton, New York 13902 (United States)

2014-11-24

The properties of molecular beam epitaxy-grown InSb{sub 1−x}Bi{sub x} alloys are investigated. Rutherford backscattering spectrometry shows that the Bi content increases from 0.6% for growth at 350 °C to 2.4% at 200 °C. X-ray diffraction indicates Bi-induced lattice dilation and suggests a zinc-blende InBi lattice parameter of 6.626 Å. Scanning electron microscopy reveals surface InSbBi nanostructures on the InSbBi films for the lowest growth temperatures, Bi droplets at intermediate temperatures, and smooth surfaces for the highest temperature. The room temperature optical absorption edge was found to change from 172 meV (7.2 μm) for InSb to ∼88 meV (14.1 μm) for InSb{sub 0.976}Bi{sub 0.024}, a reduction of ∼35 meV/%Bi.

New Processing and Characterization Approaches for Achieving Full Performance of High Temperature Superconducting Tapes of (Bi,Pb)2Sr2Ca2Cu3Ox

International Nuclear Information System (INIS)

E.E. Hellstrom; D.C. Larbalestier

2006-01-01

The thrust of this research was to identify and understand current limiting mechanisms (CLMs) that limit the current carrying capacity of (Bi,Pb) 2 Sr 2 Ca 2 Cu 3 O x (2223) in Ag-sheathed wire. Our program concentrated on developing new methods to identify CLMs at the micrometer scale and new processing techniques to eliminate CLMs. All of the DOE Superconductivity Partnership Initiative (SPI) programs are using 2223 wire, so increasing the critical current density (J c ) in the wire can improve the technical performance of the demonstration projects, and at the same time it can decrease the cost of the wire. The important cost metric for superconducting wire is $/kA·m, so increasing Jc, which is in the denominator, decreases the wire cost. The obvious CLMs were micrometer size obstacles in the 2223 ceramic that block current flow, including: misaligned grains, cracks, pores, and nonsuperconducting phases. Pores and cracks--regions where there is no superconductor or the grains are not physically connected to one another--cannot carry supercurrent, so they were the first CLMs we tried to eliminate with improved processing. Prior to the contract, we had started investigating overpressure (OP) processing with Williams at ORNL to heal cracks and remove pores. OP processing, which is a variant of hot isostatic pressing (HIP), uses an Ar/O 2 gas mixture to apply a high pressure (up to 200 atm) to compress the sample and to set the oxygen partial pressure (pO 2 ) to form 2223. Williams had a static pressure system we used to demonstrate that OP processing healed cracks and densified the wire, but the static system limited the processing parameters we could investigate. We proposed building a new gas-flow OP system to expand the experimental capabilities and to investigate new processing routes using the gas-flow OP system. Using the gas-flow OP system, we established new world records in 2003 for J c and I c . These records were finally matched by Sumitomo Electric

How do two Lupinus species respond to temperature along an altitudinal gradient in the Venezuelan Andes? ¿Cómo responden dos especies de Lupinus a la temperatura en un gradiente altitudinal en los Andes venezolanos?

Directory of Open Access Journals (Sweden)

FERMÍN RADA

2008-09-01

Full Text Available Temperature determines plant formations and species distribution along altitudinal gradients. Plants in the tropical high Andes, through different physiological and morphological characteristics, respond to freezing night temperatures and high daytime energy inputs which occur anytime of the year. The main objective of this study was to characterize day and night temperature related responses of two Lupinus species with different altitudinal ranges (L. meridanus, 1,800-3,600 and L. eromonomos, 3,700-4,300 m of altitude. Are there differences in night low temperature resistance mechanisms between the species along the gradient? How do these species respond, in terms of optimum temperature for photosynthesis, to increasing altitude? Lupinus meridanus shows frost avoidance, in contrast to L. eromonomos, which tolerates freezing at higher altitudes. Optimum temperature for photosynthesis decreases along the gradient for both species. Maximum C0(2 assimilation rates were higher in L. meridanus, while L. eromonomos showed decreasing C0(2 assimilation rates at the higher altitude. In most cases, measured daily leaf temperature is always within the 80 % of optimum for photosynthesis. L. meridanus7 upper distribution limit seems to be restricted by cold resistance mechanisms, while L. eromonomos7 to a combination of both cold resistance and to C0(2 assimilation responses at higher altitudes.La temperatura determina las formaciones vegetales y la distribución de especies a lo largo de gradientes altitudinales. Las plantas en los altos Andes tropicales, a través de diferentes características morfológicas y fisiológicas, responden a temperaturas congelantes nocturnas y altas entradas energéticas durante el día en cualquier momento del año. El objetivo principal de este estudio fue caracterizar las respuestas relacionadas con temperaturas diurnas y nocturnas en dos especies de Lupinus con diferente distribución altitudinal (L. meridanus, 1

Dispersion interactions between neighboring Bi atoms in (BiH3 )2 and Te(BiR2 )2.

Science.gov (United States)

Haack, Rebekka; Schulz, Stephan; Jansen, Georg

2018-03-13

Triggered by the observation of a short Bi⋯Bi distance and a BiTeBi bond angle of only 86.6° in the crystal structure of bis(diethylbismuthanyl)tellurane quantum chemical computations on interactions between neighboring Bi atoms in Te(BiR 2 ) 2 molecules (R = H, Me, Et) and in (BiH 3 ) 2 were undertaken. Bi⋯Bi distances atoms were found to significantly shorten upon inclusion of the d shells of the heavy metal atoms into the electron correlation treatment, and it was confirmed that interaction energies from spin component-scaled second-order Møller-Plesset theory (SCS-MP2) agree well with coupled-cluster singles and doubles theory including perturbative triples (CCSD(T)). Density functional theory-based symmetry-adapted perturbation theory (DFT-SAPT) was used to study the anisotropy of the interplay of dispersion attraction and steric repulsion between the Bi atoms. Finally, geometries and relative stabilities of syn-syn and syn-anti conformers of Te(BiR 2 ) 2 (R = H, Me, Et) and interconversion barriers between them were computed. © 2018 Wiley Periodicals, Inc. © 2018 Wiley Periodicals, Inc.

Efeitos da temperatura ambiente sobre o desempenho de suínos dos 30 aos 60 kg Effects of environmental temprerature on performance of pigs from 30 to 60 kg live weight

Directory of Open Access Journals (Sweden)

Maria Cristina Manno

2006-04-01

Full Text Available Este estudo foi conduzido para avaliar o efeito da temperatura ambiente sobre o desempenho, a composição de carcaça e os parâmetros fisiológicos de suínos de 30 a 60 kg. Foram utilizados 36 machos castrados (Landrace x Large White, com peso inicial de 29,94 ± 0,49 kg, dispostos, durante 35 dias, em três tratamentos, com seis repetições e dois animais por unidade experimental. O delineamento experimental foi o inteiramente casualizado e os tratamentos consistiram em: T1 - ambiente de calor (32ºC e alimentação à vontade; T2 - ambiente termoneutro (22ºC e alimentação à vontade; T3 - ambiente termoneutro (22ºC e alimentação equivalente ao consumo à vontade dos animais submetidos ao ambiente de calor. A temperatura ambiente elevada provocou redução do consumo de ração, porém melhorou a conversão alimentar e a eficiência de utilização de lisina para ganho. A deposição de gordura foi menor nos tratamentos 1 e 3, porém, apenas os animais em conforto térmico com alimentação pareada apresentaram declínio na deposição de proteína. Os pesos de jejum e de carcaça dos animais em estresse por calor foram menores que os dos animais em conforto térmico com alimentação à vontade, porém superiores aos dos animais com alimentação pareada. Os tratamentos não influenciaram o rendimento de carcaça e os pesos relativos dos órgãos avaliados, com exceção do estômago, que foi menor no T3. Os parâmetros fisiológicos temperaturas de superfície e freqüência respiratória foram influenciados negativamente pela alta temperatura (T1, mas a temperatura retal não foi alterada pelos tratamentos. Na fase de crescimento, a alta temperatura mantém deposição de proteína na carcaça, mas interfere negativamente no desempenho dos suínos, de modo que seus efeitos não se limitam à redução do consumo de ração.This study was carried out to evaluate the effect of environmental temperature on performance, carcass

Estudio del efecto de la temperatura sobre la fermentación acetobulítica

Directory of Open Access Journals (Sweden)

L. Cruz

1996-01-01

Full Text Available En este trabajo se estudia el efecto de la temperatura sobre la velocidad específica de crecimiento, el consumo de sustrato y la producción de solventes en la fermentación acetobutilica, FABE. Se obtuvieron las temperaturas más apropiadas para las fases acidogénica y solventogénica y la influencia de la edad del inóculo sobre el crecimiento celular y la producción de solventes.

CARACTERIZACIÓN CLIMATICA DE LA ALTA CUENCA DEL RÍO NEUQUÉN, ANDES PATAGONICOS

Directory of Open Access Journals (Sweden)

Griselda Ostertag

2005-12-01

Full Text Available En el desarrollo del presente documento se analizan las principales variables meteorológicas, temperatura y precipitación, que caracterizan y definen el clima de la Cordillera de los Andes en la Patagonia, provincia de Neuquén, particularmente en el área que ocupa la alta cuenca del río Neuquén. En esta etapa, de tipo descriptiva, el análisis estadístico refleja la situación de la climatología regional en el nivel medio histórico mediante la evaluación del comportamiento de las variables mencionadas durante los últimos 25 años. En este período se han registrado eventos extremadamente húmedos como así también situaciones de sequía. El objetivo es realizar una evaluación climática a partir de la información “in situ” de estaciones meteorológicas, información satelital y análisis estadístico para definir a posteriori, en cuál clasificación climática puede encuadrarse la zona de estudio, qué tipos climáticos pueden definirse en función de la bibliografía existente al respecto, y evaluar el grado de ajuste que presentan los climas determinados con los demás componentes del paisaje tales como vegetación y suelos.

Tendências de temperaturas mínimas e máximas do ar no Estado de Minas Gerais

Directory of Open Access Journals (Sweden)

Léo Fernandes Ávila

2014-04-01

Full Text Available O objetivo deste trabalho foi avaliar tendências das temperaturas mínimas e máximas no Estado de Minas Gerais. Foram avaliados dados de 43 municípios, tendo-se considerado as escalas anual e sazonal - janeiro, abril, julho e outubro, que representam os meses centrais de verão, outono, inverno e primavera, respectivamente. Séries históricas de temperaturas mínimas e máximas do ar diárias, com extensão mínima de 30 anos, foram analisadas com base no teste de Mann-Kendall e no uso de regressão linear simples. As tendências foram consideradas significativas somente quando ambas as avaliações foram significativas; neste caso, determinaram-se as taxas de alteração das temperaturas. Houve boa concordância entre os testes de significância para a detecção de tendências nas séries históricas, na maioria dos municípios. Observou-se tendência de elevação das temperaturas mínimas em julho de até 1,5ºC por década, com tendências generalizadas de aumento na maior parte do estado, em outubro e janeiro, e também na escala anual. Exceções foram verificadas especialmente em municípios de maiores altitudes, em que as temperaturas mínimas diminuíram no inverno. Há predominância de municípios com tendência significativa de aumento de temperaturas, independentemente da escala de avaliação. Tendências de aumento nas temperaturas são esperadas mais comumente no sentido sul-norte do Estado de Minas Gerais.

Facile synthesis of Bi/BiOCl composite with selective photocatalytic properties

International Nuclear Information System (INIS)

Chen, Dongling; Zhang, Min; Lu, Qiuju; Chen, Junfang; Liu, Bitao; Wang, Zhaofeng

2015-01-01

This paper presents a novel and facile method to fabricate Bi/BiOCl composites with dominant (001) facets in situ via a microwave reduction route. Different characterization techniques, including X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), transmission scanning electron microscopy (TEM), UV–vis diffuse reflectance spectrometry (DRS), X-ray photoelectron spectroscopy (XPS), electron spin resonance spectroscopy (ESR), cathodoluminescence spectrum (CL), and lifetime, have been employed to investigate the structure, optical and electrical properties of the Bi/BiOCl composites. The experimental results show that the introduction of Bi particles can efficiently enhance the photocatalytic performance of BiOCl for the degradation of several dyes under ultraviolet (UV) light irradiation, especially for negative charged methyl orange (MO). Unlike the UV photocatalytic performance, such Bi/BiOCl composite shows higher degradation efficiency towards rhodamine B (RhB) than MO and methylene blue (MB) under visible light irradiation. This special photocatalytic performance can be ascribed to the synergistic effect between oxygen vacancies and Bi particles. This work provides new insights about the photodegradation mechanisms of MO, MB and RhB under UV and visible light irradiation, which would be helpful to guide the selection of an appropriate catalyst for other pollutants. - Highlights: • Bi/BiOCl composites were synthesized via a microwave reduction. • Tunable selectivity photocatalytic activity can be achieved. • Photodegradation mechanism under UV and visible light were proposed

Efecto de la temperatura en la sobrevivencia embrionaria del puye Galaxias maculatus (Jenyns, 1842

Directory of Open Access Journals (Sweden)

Juan Bariles

2013-11-01

Full Text Available Se evaluó el efecto de seis temperaturas constantes en la sobrevivencia embrionaria, periodo embrionario y periodo de eclosión de Galaxias maculatus de 7 a 22°C, en condiciones de laboratorio. Los resultados de la sobrevivencia embrionaria fueron: 90,6 ± 2,0; 88,7 ± 8,6; 87,7 ± 0,7; 89,7 ± 4,2; 70,0 ± 5,6 y 49,5 ± 7,4% a temperaturas de 7, 10, 13, 16, 19 y 22°C. Exceptuando la temperatura de 22°C, no hay diferencias significativas entre ellas (P > 0,05. Estos resultados caracterizan al embrión como euritérmico independientemente de ser una especie de aguas subantárticas. En relación al periodo embrionario (tH50%, los resultados fueron de 40,8 ± 0,6; 27,0 ± 0,0; 17,3 ± 0,6; 16,3 ± 0,6 y 13,3 ± 0,6 días a temperaturas de 7, 10, 13, 16 y 19°C respectivamente, con diferencias significativas entre ellas (P 87,7%, periodos embrionarios <27 días y periodos de eclosión <6,3 días. Estos resultados permitirán optimizar la sobrevivencia embrionaria y el eventual cultivo de la especie para fines comerciales o de repoblamiento.

Transport Barkhausen-like noise in uniaxially pressed Bi{sub 1.65}Pb{sub 0.35}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub 10+{delta}}ceramic samples

Energy Technology Data Exchange (ETDEWEB)

Garcia-Fornaris, I. [Departamento de Ciencias Basicas, Universidad de Granma, Apdo. 21, P.O. Box 85100, Bayamo (Cuba); Govea-Alcaide, E. [Departamento de Fisica, Universidad de Oriente, Patricio Lumumba s/n, P.O. Box 90500, Santiago de Cuba (Cuba); Instituto de Fisica, Universidade de Sao Paulo, CP 66318, 05315-970 Sao Paulo, SP (Brazil); Alberteris-Campos, M. [Departamento de Engenharia Mecanica, Escola Politecnica, Universidade de Sao Paulo, 05508-900 Sao Paulo, SP (Brazil); Mune, P. [Departamento de Fisica, Universidad de Oriente, Patricio Lumumba s/n, P.O. Box 90500, Santiago de Cuba (Cuba); Jardim, R.F., E-mail: rjardim@if.usp.b [Instituto de Fisica, Universidade de Sao Paulo, CP 66318, 05315-970 Sao Paulo, SP (Brazil)

2010-08-01

We report on the detection of the transport Barkhausen-like noise (TBN) in polycrystalline samples of Bi{sub 1.65}Pb{sub 0.35}Sr{sub 2}Ca{sub 2} Cu{sub 3}O{sub 10+{delta}}(Bi-2223) which were subjected to different uniaxial compacting pressures. The transport Barkhausen-like noise was measured when the sample was subjected to an ac triangular-shape magnetic field (f {approx} 1 Hz) with maximum amplitude B{sub max} {approx} 5.5 mT, in order to avoid the flux penetration within the superconducting grains. Analysis of the TBN signal, measured for several values of excitation current density, indicated that the applied magnetic field in which the noise signal first appears, B{sub a}(t{sub i}), is closely related to the magnetic-flux pinning capability of the material. The combined results are consistent with the existence of three different superconducting levels within the samples: (i) the superconducting grains; (ii) the superconducting clusters; and (iii) the weak-links. We finally argue that TBN measurements constitute a powerful tool for probing features of the intergranular transport properties in polycrystalline samples of high-T{sub c} superconductors.

Efeito dos solventes orgânicos sobre o comportamento físico-químico do polietileno de alta densidade (PEAD e polipropileno (PP

Directory of Open Access Journals (Sweden)

Thieres Magaive Costa Pereira

2014-06-01

Full Text Available O mercado brasileiro de embalagens empregado ao armazenamento de petróleo e seus derivados vem crescendo a cada ano, sendo constituídas basicamente por polietileno de alta densidade (PEAD e polipropileno (PP. Contudo durante o armazenamento, a matriz polimérica fica exposta ao óleo, comprometendo suas propriedades físicas e consequentemente a durabilidade do material. Portanto, estudos relacionados com a interação entre solventes orgânicos e a matriz polimérica tornam-se importantes. Neste trabalho, a interação do PEAD e PP com diferentes solventes apolares (tolueno, n-heptano, n-decano e n-tetradecano foram estudadas em função da temperatura (25, 50 e 80 ºC. Os valores de ganho de massa, coeficientes de difusão, sorção, permeabilidade e parâmetros de mecanismo de transporte foram calculados. O ganho de massa observado para o PP foi maior do que para o PEAD, em todas as temperaturas, sendo que o tolueno foi o solvente responsável pelo maior ganho de massa, atingindo o equilíbrio em um menor intervalo de tempo. Esse resultado corrobora com os valores de coeficiente de difusão e de permeabilidade, que aumentaram na seguinte ordem: n-heptano > n-decano > n-tetradecano. Uma ordem inversa foi observada para os solventes alifáticos quando os valores de coeficiente de sorção foram calculados. O mecanismo de transporte foi também estudado através da regressão dos dados de sorção, sendo classificado como anômalo.

Bismuth-boron multiple bonding in BiB_2O"- and Bi_2B"-

International Nuclear Information System (INIS)

Jian, Tian; Cheung, Ling Fung; Chen, Teng-Teng; Wang, Lai-Sheng

2017-01-01

Despite its electron deficiency, boron is versatile in forming multiple bonds. Transition-metal-boron double bonding is known, but boron-metal triple bonds have been elusive. Two bismuth boron cluster anions, BiB_2O"- and Bi_2B"-, containing triple and double B-Bi bonds are presented. The BiB_2O"- and Bi_2B"- clusters are produced by laser vaporization of a mixed B/Bi target and characterized by photoelectron spectroscopy and ab initio calculations. Well-resolved photoelectron spectra are obtained and interpreted with the help of ab initio calculations, which show that both species are linear. Chemical bonding analyses reveal that Bi forms triple and double bonds with boron in BiB_2O"- ([Bi≡B-B≡O]"-) and Bi_2B"- ([Bi=B=Bi]"-), respectively. The Bi-B double and triple bond strengths are calculated to be 3.21 and 4.70 eV, respectively. This is the first experimental observation of Bi-B double and triple bonds, opening the door to design main-group metal-boron complexes with multiple bonding. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

The modulation and reconstruction of a BiO layer of cuprate Bi2212

International Nuclear Information System (INIS)

Fan Wei; Zeng, Z

2011-01-01

Studies based on ab initio density functional theory show that the modulated structures of BiO surfaces of cuprate Bi2212 superconductors are spontaneously formed and closely related to the reconstructions of BiO surfaces. The reconstructions of BiO layers occur both on the surface and in the bulk, accompanied with the formations of BiO-zigzag chains and Bi 2 O 2 quadrilaterals. The structural modulations of the BiO surface are along the b axis, perpendicular to the BiO-zigzag chains along the a axis. Our calculations provide a unified understanding of the formation of modulating structures in Bi2212. Another interesting result is that electronic structures of BiO surfaces are significantly influenced by the CuO 2 layer beneath because of the structural modulations and reconstructions.

Novel Bi/BiOBr/AgBr composite microspheres: Ion exchange synthesis and photocatalytic performance

Science.gov (United States)

Lyu, Jianchang; Li, Zhenlu; Ge, Ming

2018-06-01

Novel Bi/BiOBr/AgBr composite microspheres were prepared by a rational in situ ion exchange reaction between Bi/BiOBr microspheres and AgNO3. The characteristic of the as-obtained ternary microspheres was tested by X-ray diffraction (XRD), energy dispersive X-ray spectrometer (EDS), scanning electron microscope (SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy (UV-vis DRS) and photoluminescence (PL). Under visible light irradiation, Bi/BiOBr/AgBr microspheres exhibited an excellent photocatalytic efficiency for rhodamine B (RhB) degradation, which was about 1.4 and 4.9 times as high as that of Bi/BiOBr and BiOBr/AgBr, demonstrating that the highest separation efficiency of charge carriers in the heterostructured Bi/BiOBr/AgBr. The photocatalytic activity of Bi/BiOBr/AgBr microspheres just exhibited a slight decrease after three consecutive cycles. The photocatalytic mechanism investigation confirmed that the superoxide radicals (O2•-) were the dominant reactive oxygen species for RhB degradation in Bi/BiOBr/AgBr suspension.

Photocatalytic activity of Bi_2WO_6/Bi_2S_3 heterojunctions: the facilitation of exposed facets of Bi_2WO_6 substrate

International Nuclear Information System (INIS)

Yan, Long; Wang, Yufei; Shen, Huidong; Zhang, Yu; Li, Jian; Wang, Danjun

2017-01-01

Highlights: • Bi_2S_3/Bi_2WO_6 hybrids with exposed (020) Bi_2WO_6 facets have been synthesized. • X-ray photoelectron spectroscopy reveals that a small amount of Bi_2S_3 was formed. • The enhanced photoactivity of hybrids is due to heterojunction and (020) facets. • A possible photocatalytic degradation mechanism is proposed. - Abstract: Bi_2S_3/Bi_2WO_6 hybrid architectures with exposed (020) Bi_2WO_6 facets have been synthesized via a controlled anion exchange approach. X-ray photoelectron spectroscopy (XPS) reveals that a small amount of Bi_2S_3 was formed on the surface of Bi_2WO_6 during the anion exchange process, thus leading to the transformation from the Bi_2WO_6 to Bi_2S_3/Bi_2WO_6. A rhodamine B (RhB) aqueous solution was chosen as model organic pollutants to evaluate the photocatalytic activities of the Bi_2S_3/Bi_2WO_6 catalysts. Under visible light irradiation, the Bi_2S_3/Bi_2WO_6-TAA displayed the excellent visible light photoactivities compared with pure Bi_2S_3, Bi_2WO_6 and other composite photocatalysts. The efficient photocatalytic activity of the Bi_2S_3/Bi_2WO_6-TAA composite microspheres was ascribed to the constructed heterojunctions and the inner electric field caused by the exposed (020) Bi_2WO_6 facets. Active species trapping experiments revealed that h"+ and O_2·"− are the main active species in the photocatalytic process. Furthermore, the as-obtained photocatalysts showed good photocatalytic activity after four recycles. The results presented in this study provide a new concept for the rational design and development of highly efficient photocatalysts.

Impact of environmental temperatures on resistance to organophosphate insecticides in Aedes aegypti from Trinidad Repercusión de las temperaturas ambientales sobre la resistencia de Aedes aegypti a los insecticidas organofosforados en Trinidad

Directory of Open Access Journals (Sweden)

Karen A. Polson

2012-07-01

, los aumentos o las disminuciones en los niveles de actividad de las enzimas no siempre se correspondieron con un aumento o disminución en la proporción de individuos resistentes desarrollados a las temperaturas más altas. CONCLUSIONES: Aunque el recalentamiento del planeta puede causar un aumento de la transmisión del dengue, según los resultados de este estudio el uso de insecticidas para la prevención y el control del dengue todavía puede ser eficaz si las temperaturas aumentan según lo proyectado.

Heterojunction BiOI/Bi2MoO6 nanocomposite with much enhanced photocatalytic activity

International Nuclear Information System (INIS)

Li, Wen Ting; Zheng, Yi Fan; Yin, Hao Yong; Song, Xu Chun

2015-01-01

BiOI/Bi 2 MoO 6 heterostructures with different amounts of BiOI were successfully prepared via a facile deposition method. The obtained BiOI/Bi 2 MoO 6 photocatalysts exhibited much higher visible light (λ > 420 nm) induced photocatalytic activity compared with single Bi 2 MoO 6 and BiOI photocatalysts. 20 % BiOI/Bi 2 MoO 6 nanocomposite exhibited the highest photocatalytic activity with almost all RhB decomposed within 70 min. However, excess BiOI covering on the surface of Bi 2 MoO 6 can inversely reduce the photocatalytic activity. The enhanced photocatalytic activities could be resulted from the function of the novel p–n heterojunction interface between Bi 2 MoO 6 and BiOI, which could separate photoinduced carriers efficiently. Possible mechanisms on the basis of the relative band positions were also discussed

Multiferroic BiFeO3-BiMnO3 Nanocheckerboard From First Principles

OpenAIRE

Palova, L.; Chandra, P.; Rabe, K. M.

2010-01-01

We present a first principles study of an unusual heterostructure, an atomic-scale checkerboard of BiFeO3-BiMnO3, and compare its properties to the two bulk constituent materials, BiFeO3 and BiMnO3. The "nanocheckerboard" is found to have a multiferroic ground state with the desired properties of each constituent: polar and ferrimagnetic due to BiFeO3 and BiMnO3, respectively. The effect of B-site cation ordering on magnetic ordering in the BiFeO3-BiMnO3 system is studied. The checkerboard ge...

Los profesores de alumnos con altas habilidades

Directory of Open Access Journals (Sweden)

Cándido GENOVARD

2010-01-01

Full Text Available En este trabajo analizamos las características de los profesores expertos para alumnos de altas habilidades. Se analizan los antecedentes del tema y el proceso instruccional para atender la diversidad de estos alumnos. Se destaca el valor de las interacciones entre profesor¿ alumnos y los estilos de enseñar y aprender. Asimismo, recogemos pautas de acción y recursos instruccionales a utilizar en el aula para la enseñanza de estos alumnos. No hay un profesor ideal para los alumnos con altas habilidades, pero los docentes deben conocer qué son y cómo funcionan los procesos de enseñanza¿aprendizaje y las variables psicológicas, de contenidos y contextuales implicadas en éstos.

INFLUÊNCIA DA TEMPERATURA NA REOLOGIA DE FLUIDOS DE PERFURAÇÃO PREPARADOS COM CARBOXIMETILCELULOSE, GOMA XANTANA E BENTONITA

Directory of Open Access Journals (Sweden)

Klismeryane Costa de Melo

2013-10-01

Full Text Available O comportamento reológico dos fluidos de perfuração pode sofrer alterações ao longo da perfuração em função do gradiente de temperatura do poço. A degradação térmica sofrida por alguns aditivos utilizados como viscosificantes restringe a utilização da classe dependendo da temperatura a qual será exposto. Este trabalho apresenta um estudo sobre o comportamento reológico da Goma Xantana (GX, da Carboximetilcelulose (CMC e da Bentonita (BNT em função da temperatura. Os Modelos matemáticos de Ostwald de Waale e o de Herschel-Bulkley foram aplicados para determinar os parâmetros reológicos. O efeito da hidratação dos polímeros e da argila na reologia de soluções aquosas foram previamente estudados. A caracterização reológica foi realizada através de ensaios de reologia, utilizando sistema de cilindros coaxiais, para obtenção das curvas de fluxo. A reologia foi avaliada em função da temperatura para cada um dos aditivos utilizados. Os resultados mostraram que a CMC se solubiliza rapidamente em água, porém apresenta maior degradação quando exposta a temperatura mais elevada. A GX se mostrou apta para ser utilizada em formulações de fluidos que serão usados em poços com gradiente de temperatura mais elevados. A bentonita não apresentou alterações no comportamento reológico em função do gradiente de temperatura estudado.

Percepción socioemocional de los profesores en adolescentes con altas habilidades versus habilidades medias

Directory of Open Access Journals (Sweden)

Mari Carmen FERNÁNDEZ

2011-01-01

Full Text Available El objetivo de este trabajo es estudiar la percepción que los profesores tienen sobre las competencias socioemocionales de sus alumnos adolescentes, según la excepcionalidad (alta habilidad vs. no alta habilidad y el género. La muestra estuvo compuesta por 443 profesores pertenecientes a 55 centros de Educación Secundaria Obligatoria de la Región de Murcia. El instrumento utilizado fue el EQ-i, YV-O dirigido a profesores (BAR-ON & PARKER, en prensa. Los resultados indicaron, según la excepcionalidad de los alumnos (alta habilidad vs. no alta habilidad, que los profesores percibieron al grupo de alumnos de alta habilidad más adaptados, con mayor estado de ánimo y con mayores habilidades interpersonales. Respecto al género, los profesores valoraron con mayor manejo del estrés a los chicos. Además, según la excepcionalidad (alta habilidad vs. no alta habilidad y el género, los datos mostraron diferencias estadísticamente significativas para las dimensiones adaptabilidad, estado de ánimo e intrapersonal.

Efeito da temperatura e do tempo de armazenamento sobre a contagem de células somáticas no leite Effects of temperature and storage on somatic cell counts in milk

Directory of Open Access Journals (Sweden)

G.N. Souza

2005-12-01

Full Text Available Avaliou-se o efeito da temperatura e do tempo de armazenamento sobre a contagem de células somáticas(CCS. Amostras de leite de 21 vacas, coletadas e armazenadas às temperaturas de 5, 27, 32 e 36ºC e analisadas no 1º, 3º, 5º e 7º dia após coleta, foram classificadas em três grupos (células/ml: baixa (236.000±164.000, média (624.000±356.000 e alta CCS (1.320.000±945.000. O delineamento experimental foi o de parcelas subdivididas. As médias da CCS foram iguais (P>0,05 para amostras mantidas à temperatura de 5ºC e analisadas entre o primeiro e o sétimo dias após a coleta e para aquelas mantidas às temperaturas 5, 27, 32 e 36ºC e analisadas no primeiro dia. Médias diferentes (PEffects of temperature and storage duration on somatic cell counts (SCC of milk samples were studied in a split plot design with seven replicates. Samples from 21 cows were maintained at 5, 27, 32 or 36ºC (plots and analyzed after 1, 3, 5 and 7 days of storage (split plots. Based upon an initial analysis, samples were classified into three groups: low (236,000±164,000, medium (624,000±356,000 and high (1,320,000±945,000 SCC/ml. No significant differences in SCC (P>0.05 were observed among storage temperatures for milk samples tested after one day of storage. For milk samples stored at 5°C, SCC averages did not significantly change (P>0.05 until the seventh day after collection. On days 5, 5 and 3, respectively, average SCC decreased for milk samples stored at 27, 32 and 36°C. Reductions of 57.6% (from 236,000 to 100,000, 58.5% (from 624,000 to 259,000 and 27.5% (from 1,320,000 to 952,000 from initial numbers of somatic cells were observed for samples classified as low, medium and high, respectively. Milk samples must be kept under refrigeration until analysis, and SCC must be measured within 7 days of sample collection.

Crioterapia no pos-parto: tempo de aplicacao e mudancas na temperatura perineal

OpenAIRE

Adriana Amorim Francisco; Sonia Maria Junqueira Vasconcellos de Oliveira; Lucila Coca Leventhal; Caroline de Souza Bosco

2013-01-01

Estudo descritivo com dados de dois ensaios clínicos realizados em 2008 e 2009 em uma maternidade de uma instituição filantrópica da cidade de São Paulo. Teve como objetivo descrever a temperatura perineal após a aplicação de bolsa de gelo no pós-parto normal. Três grupos com 38 puérperas cada (n=114) receberam aplicação perineal de bolsa de gelo entre 2 e 48h após o parto. Os achados indicaram que com 10 min de crioterapia as médias da temperatura perineal atingiram de 13,3 a 15,3oC, com peq...

Tema 4. Calor y temperatura (Guía del tema)

OpenAIRE

Beléndez Vázquez, Augusto

2010-01-01

Guía del "Tema 4. Calor y temperatura" de la asignatura "Fundamentos Físicos de la Ingeniería I" del "Grado en Ingeniería en Sonido e Imagen" impartido en la Escuela Politécnica Superior de la Universidad de Alicante.

In-situ synthesis of nanofibers with various ratios of BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z} for effective trichloroethylene photocatalytic degradation

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yifan [Department of Chemistry, Inha University, 100 Inharo, Incheon 402-751 (Korea, Republic of); Park, Mira [Department of Organic Materials and Fiber Engineering, Chonbuk National University, Jeonju 561-756 (Korea, Republic of); Kim, Hak Yong [Department of BIN Convergence Technology, Chonbuk National University, Jeonju, 561-756 (Korea, Republic of); Ding, Bin [College of Textiles, Donghua University, Shanghai 201620 (China); Park, Soo-Jin, E-mail: sjpark@inha.ac.kr [Department of Chemistry, Inha University, 100 Inharo, Incheon 402-751 (Korea, Republic of)

2016-10-30

Highlights: • BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z}/PAN fibers were synthesized by in-situ method. • Photodegradation behavior of BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z}/PAN fibers was measured under solar light irradiation. • BiOCl{sub 0.3}/BiOBr{sub 0.3}/BiOI{sub 0.4}/PAN fibers exhibited the highest photocatalytic activity. • Photocatalytic mechanism was discussed in detail. - Abstract: In this work, BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z} (x + y + z = 1) composite nanofibers were prepared through electrospinning and the sol-gel methods. Photocatalytic degradation of trichloroethylene (TCE) by BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z}/PAN nanofibers was systematically investigated via gas chromatography (GC). Optimum photocatalytic activity was achieved with BiOCl{sub 0.3}/BiOBr{sub 0.3}/BiOI{sub 0.4} fibers under solar light irradiation. X-ray photoelectron spectroscopy (XPS) peaks due to C−O and C=O were observed at 286.0 and 288.3 eV, respectively, it indicated that the BiOCl{sub x}/BiOBr{sub y}/BiOI{sub z} mixture had been successfully doped on the polyacrylonitrile (PAN) fibers. Furthermore, X-ray diffraction (XRD) results also confirmed that we had synthesized the as-prepared composite nanofibers successfully. Photocatalytic activities of BiOCl{sub 0.3}/BiOBr{sub 0.3}/BiOI{sub 0.4} were up to 3 times higher than the pure BiOCl, BiOBr and BiOI samples, respectively.

Aumento de la temperatura en la superficie dental durante la foto-polimerización

OpenAIRE

Hernández, Douglas Jarquín; Bonilla, Silvia

2016-01-01

ResumenSe sabe que durante el fotocurado de los materiales dentales se libera calor, ya sea por parte de la fuente emisora de luz o por la reacción de polimerización del compuesto utilizado. Este aumento de temperatura se transmite a los tejidos, el cual puede repercutir en ellos. Debido a esto, se realiza un estudio comparativo de la temperatura alcanzada durante la obturación y reconstrucción de piezas dentales in vitro, utilizando lámparas de fotocurado de tipo cuarzo-tungsteno-halógeno (Q...

Desarrollo de un sensor de temperatura remoto basado en la radiación infrarroja

OpenAIRE

Díaz García, Abraham de los Ángeles

2012-01-01

Este proyecto fin de carrera se centra en el estudio y diseño de un sensor de temperatura remoto. El objetivo principal del proyecto es desarrollar un dispositivo capaz de obtener la temperatura de un objeto situado a una cierta distancia, conocida su emisividad y la radiación infrarroja emitida por éste. Además, se plantea dentro de este proyecto el estudio de los principios básicos de termometría infrarroja y la clasificación de los distintos tipos de termopilas en el mercado atendiendo a s...

Facile Fabrication of BiOI/BiOCl Immobilized Films With Improved Visible Light Photocatalytic Performance

Directory of Open Access Journals (Sweden)

Yingxian Zhong

2018-03-01

Full Text Available HIGHLIGHTSA facial method was used to fabricate BiOI/BiOCl film at room temperature.30% BiOI/BiOCl showed an excellent photocatalytic activity and stability.Improvement of photocatalytic activity was owed to expanded visible light absorption and high separation efficiency of charge.Photocatalysis has been considered to be one of the most promising ways to photodegrade organic pollutants. Herein, a series of BiOI/BiOCl films coating on FTO were fabricated through a simple method at room temperature. The photocatalytic efficiency of 30%BiOI/BiOCl could reach more than 99% aiming to degrading RhB and MB after 90 and 120 min, respectively. Compared with BiOCl, 30%BiOI/BiOCl showed 12 times higher efficiency when degrading RhB. In comparison with BiOI, 30%BiOI/BiOCl showed 5 and 6 times higher efficiency when degrading RhB and MB, respectively. These obvious enhancements were attributed to expanded visible light absorption and high separation performance of photoinduced charge. Moreover, the photocatalytic activity of 30%BiOI/BiOCl had no obvious decrease after five recycles, suggesting that it was a promising photocatalyst for the removal of MB and RhB pollutants. Finally, the possible growth process for the BiOI/BiOCl thin films and photocatalysis mechanism were investigated in details. This work would provide insight to the reasonable construction of BiOX heterojunction and the photocatalytic mechanism in degrading organic pollutants.

Influence of photoinduced Bi-related self-doping on the photocatalytic activity of BiOBr nanosheets

Energy Technology Data Exchange (ETDEWEB)

Wu, Dan [School of Life Sciences, The Chinese University of Hong Kong, Shatin, NT, Hong Kong SAR (China); Yue, Songtao; Wang, Wei [College of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074 (China); An, Tiacheng, E-mail: antc99@gig.ac.cn [Institute of Environmental Health and Pollution Control, School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006 (China); Li, Guiying [Institute of Environmental Health and Pollution Control, School of Environmental Science and Engineering, Guangdong University of Technology, Guangzhou 510006 (China); Ye, Liqun [School of Life Sciences, The Chinese University of Hong Kong, Shatin, NT, Hong Kong SAR (China); College of Chemistry and Pharmaceutical Engineering, Nanyang Normal University, Nanyang 473061 (China); Yip, Ho Yin [School of Life Sciences, The Chinese University of Hong Kong, Shatin, NT, Hong Kong SAR (China); Wong, Po Keung, E-mail: pkwong@cuhk.edu.hk [School of Life Sciences, The Chinese University of Hong Kong, Shatin, NT, Hong Kong SAR (China)

2017-01-01

Highlights: • Bi{sup 5+} self-doped BiOBr nanosheets are achieved under UV irradiation. • Bi{sup 5+} is formed due to the oxidation of surface Bi{sup 3+} by photoexcited h{sup +} of BiOBr. • Two photoinduced h{sup +} mediated oxidation processes happen simultaneously. • Self-doped BiOBr is superior in phenol degradation and bacterial inactivation. • Bi{sup 5+} electron trapping induced photocatalytic enhancement mechanism is proposed. - Abstract: Under UV irradiation, self-doped Bi{sup 5+} is evidenced to be generated on the surface of BiOBr nanosheets, but with well-preserved crystal structure and morphology compared with pure counterpart. Bi{sup 5+} self-doping BiOBr (BiOBr-4) exhibits distinct photocatalytic mode for dyes degradation, as compared with pure BiOBr nanosheets. These photodegradation distinctions are mainly due to the simultaneous occurrence of two photoinduced hole (h{sup +}) mediated oxidation processes on the BiOBr surfaces: (1) a portion of photoexcited h{sup +} participates in the photocatalytic oxidation of dyes, and (2) partial h{sup +} involves the oxidation of Bi{sup 3+} to Bi{sup 5+}. Notably, BiOBr-4 nanosheets comparatively show superior photocatalytic activity for the phenol decomposition as well as the bacterial inactivation. Besides Bi{sup 5+} induced narrowed bandgap and enhanced light adsorption capacity, significantly, the oxidative Bi{sup 5+} acts as electron traps to promote the photoexcited electron-hole separation and accelerate h{sup +} migration, resulting in the considerable photocatalytic enhancement of BiOBr-4 nanosheets. These novel findings will not only give new insights into the photocatalytic mechanism but also explore new route to enhance photocatalytic performance of Bi-based materials.

Towards a 20 kA high temperature superconductor current lead module using REBCO tapes

Science.gov (United States)

Heller, R.; Bagrets, N.; Fietz, W. H.; Gröner, F.; Kienzler, A.; Lange, C.; Wolf, M. J.

2018-01-01

Most of the large fusion devices presently under construction or in operation consisting of superconducting magnets like EAST, Wendelstein 7-X (W7-X), JT-60SA, and ITER, use high temperature superconductor (HTS) current leads (CL) to reduce the cryogenic load and operational cost. In all cases, the 1st generation HTS material Bi-2223 is used which is embedded in a low-conductivity matrix of AgAu. In the meantime, industry worldwide concentrates on the production of the 2nd generation HTS REBCO material because of the better field performance in particular at higher temperature. As the new material can only be produced in a multilayer thin-film structure rather than as a multi-filamentary tape, the technology developed for Bi-2223-based current leads cannot be transferred directly to REBCO. Therefore, several laboratories are presently investigating the design of high current HTS current leads made of REBCO. Karlsruhe Institute of Technology is developing a 20 kA HTS current lead using brass-stabilized REBCO tapes—as a further development to the Bi-2223 design used in the JT-60SA current leads. The same copper heat exchanger module as in the 20 kA JT-60SA current lead will be used for simplicity, which will allow a comparison of the newly developed REBCO CL with the earlier produced and investigated CL for JT-60SA. The present paper discusses the design and accompanying test of single tape and stack REBCO mock-ups. Finally, the fabrication of the HTS module using REBCO stacks is described.

Propiedades termofísicas del jugo concentrado de lulo a temperaturas por encima del punto de congelación Propriedades termofísicas de suco concentrado de lulo em temperaturas acima do ponto de congelamento

Directory of Open Access Journals (Sweden)

Glória Ines Giraldo-Gómez

2010-05-01

Full Text Available En este trabajo fueron determinados experimentalmente el calor específico, conductividad térmica, difusividad térmica y densidad del jugo de lulo en el rango de contenido de agua de 0.55 a 0.90 (p/p en base húmeda y en temperaturas variando de 4 a 78.6 °C. La conductividad térmica y el calor específico fueron obtenidos utilizando el mismo aparato - una célula constituida de dos cilindros concéntricos - operando en estado estacionario y no- estacionario, respectivamente. La difusividad térmica fue obtenida a través del método de Dickerson y la densidad determinada por picnometria. Tanto la temperatura como el contenido de agua presentaron una fuerte influencia en los datos experimentales de las propiedades termofísicas del jugo de lulo. Los resultados obtenidos fueron utilizados para obtener modelos matemáticos y predecir estas propiedades en función de la concentración y la temperatura.Neste trabalho, foram determinados experimentalmente o calor específico, a condutividade térmica, difusividade térmica e densidade de suco de lulo na faixa de conteúdo de água entre 0,55 e 0,90 (p/p em base úmida e em temperaturas entre 4 e 78,6 °C. A condutividade térmica e o calor específico foram obtidos utilizando-se o mesmo equipamento - uma célula constituída de dois cilindros concêntricos - operando em estado estacionário e não estacionário, respectivamente. A difusividade térmica foi obtida através do método de Dickerson e a densidade determinada por picnometria. Tanto a temperatura como o conteúdo de água apresentaram grande influência nos dados experimentais das propriedades termofísicas do suco de lulo. Os resultados obtidos foram utilizados na obtenção de modelos matemáticos para predizer estas propriedades em função da concentração e temperatura.

Bi3+–Pr3+ energy transfer processes and luminescent properties of LuAG:Bi,Pr and YAG:Bi,Pr single crystalline films

International Nuclear Information System (INIS)

Zorenko, Y.; Gorbenko, V.; Savchyn, V.; Zorenko, T.; Nikl, M.; Mares, J.A.; Beitlerova, A.; Jary, V.

2013-01-01

Absorption, cathodoluminescence, excitation spectra of photoluminescence (PL) and PL decay kinetics were studied at 300 K for the double doped with Bi 3+ –Pr 3+ and separately doped with Bi 3+ and Pr 3+ Lu 3 Al 5 O 12 (LuAG) and Y 3 Al 5 O 12 (YAG) single crystalline film (SCF) phosphors grown by the liquid phase epitaxy method. The emission bands in the UV range arising from the intrinsic radiative transitions of Bi 3+ based centers, and emission bands in the visible range, related to the luminescence of excitons localized around Bi 3+ based centers, were identified both in Bi–Pr and Bi-doped LuAG and YAG SCFs. The energy transfer processes from the host lattice simultaneously to Bi 3+ and Pr 3+ ions and from Bi 3+ to Pr 3+ ions were investigated. Competition between Pr 3+ and Bi 3+ ions in the energy transfer processes from the LuAG and YAG hosts was evidenced. The strong decrease of the intensity of Pr 3+ luminescence both in LuAG:Pr and YAG:Pr SCFs phosphors, grown from Bi 2 O 3 flux, is observed due to the quenching influence of Bi 3+ flux related impurity. Due to overlap of the UV emission band of Bi 3+ centers with the f–d absorption bands of Pr 3+ ions in the UV range and the luminescence of excitons localized around Bi ions with the f–f absorption bands of Pr 3+ ions in the visible range, an effective energy transfer from Bi 3+ ions to Pr 3+ ions takes place in LuAG:Bi,Pr and YAG:Bi,Pr SCFs, resulting in the appearance of slower component in the decay kinetics of the Pr 3+ d–f luminescence. -- Highlights: • Bi and Pr doped film phosphor grown by liquid phase epitaxy method. • Energy transfer from Bi 3+ to Pr 3+ ions. • Strong quenching of the Pr 3+ luminescence by Bi 3+ co-dopant

Facile Fabrication of BiOI/BiOCl Immobilized Films with Improved Visible Light Photocatalytic Performance

Science.gov (United States)

Zhong, Yingxian; Liu, Yuehua; Wu, Shuang; Zhu, Yi; Chen, Hongbin; Yu, Xiang; Zhang, Yuanming

2018-03-01

Photocatalysis has been considered to be one of the most promising ways to photodegrade organic pollutants. Herein, a series of BiOI/BiOCl films coating on FTO were fabricated through a simple method at room temperature. The photocatalytic efficiency of 30%BiOI/BiOCl could reach more than 99% aiming to degrading RhB and MB after 90 and 120 min, respectively. Compared with BiOCl, 30%BiOI/BiOCl showed 12 times higher efficiency when degrading RhB. In comparison with BiOI, 30%BiOI/BiOCl showed 5 and 6 times higher efficiency when degrading RhB and MB, respectively. These obvious enhancements were attributed to expanded visible light absorption and high separation performance of photoinduced charge. Moreover, the photocatalytic activity of 30%BiOI/BiOCl had no obvious decrease after 5 recycles, suggesting that it was a promising photocatalyst for the removal of MB and RhB pollutants. Finally, the possible growth process for the BiOI/BiOCl thin films and photocatalysis mechanism were investigated in details. This work would provide insight to the reasonable construction of BiOX heterojunction and the photocatalytic mechanism in degrading organic pollutants.

Study of AFP level in the blood serum of the 2223 normal pregnant women

International Nuclear Information System (INIS)

Wang Yunhui; Huo Tongshu; Ji Changqing; Mei Nan; Zhang Tao

1993-01-01

The authors have reported AFP level in the blood serum of 2223 normal pregnant women in different semesters by RIA method. All the data were made by statistical analysis. The result shows that the AFP level is normal during the first 12 weeks of pregnancy. Then, it gradually increases from the 13th week and reaches its maximum (184.6 +- 74.6 μg/l) at 32nd week. Later on it tends to decrease slowly, but still remains over 100 μg/l in parturition period. Therefore, it is suggested that AFP in pregnant women has substantial difference and regularity between different semesters but without any significant correlation with their ages

Comportamento dos antitérmicos ibuprofeno e dipirona em crianças febris

Directory of Open Access Journals (Sweden)

Ana Maria Magni

2011-02-01

Full Text Available OBJETIVO: Analisar o comportamento da temperatura em crianças febris medicadas com dose oral única do ibuprofeno (10 mg/kg, dose recomendada para febre alta, comparado à dipirona (15 mg/kg, dose preconizada pelo fabricante, após 2, 3, 4, 5, 6, 7 e 8 horas da medicação antitérmica. MÉTODOS: Ensaio clínico, aberto e randomizado (1:1, em crianças de ambos os sexos, com doenças febris, com idade entre 6 meses e 8 anos, temperatura axilar basal entre 38,0 e 40,3 °C, e divididas em dois grupos: febre alta (> 39,1 °C e febre baixa (38,0 a 39,1 °C. A análise do comportamento baseou-se nos critérios de descontinuidade, segurança, resposta ao tratamento, tolerabilidade e eficácia terapêutica. RESULTADOS: Das 80 crianças, 31 permaneceram afebris ao longo de 8 horas (38,8%, 100,0% obtiveram decréscimo da temperatura com ambas as medicações nas 2 primeiras horas. No grupo de febre alta, 11 crianças medicadas com ibuprofeno foram mantidas até a 5ª hora (100,0%, e 11 com dipirona até a 3ª hora (100,0%. A eficácia antipirética na febre alta foi estatisticamente significante a favor do ibuprofeno na 3ª e na 4ª hora, e, na febre baixa, na 3ª hora após a medicação. CONCLUSÕES: Este estudo demonstrou que, em dose oral única, o ibuprofeno proporciona atividade antipirética mais acentuada do que a dipirona, principalmente na febre alta. Ambas as medicações foram bem toleradas e seguras em curto prazo.

La temperatura del interior de la tierra

Directory of Open Access Journals (Sweden)

Eslava R. Jesús A.

1993-10-01

Full Text Available The problem of defining the Earth interior temperature is analized from Heat Flow observations and the acceptance of convection processes in the mantle. Comparative analyses of thermal, adiabatic, and melting point profiles, allow to obtain the optimum temperature profile, wich fits the seismic model of a liquid external core.

EI problema de definir la temperatura del interior de la Tierra, se analiza a partir de las observaciones del flujo térmico y la aceptación de procesos de convección en el manto.

Análisis comparativos de perfiles térmicos, adiabáticos y de puntos de fusión, permiten obtener un perfil óptimo de distribución de temperaturas, que además satisface la observación sísmica de un núcleo externo líquido.

Temperatura neutral y rangos de confort térmico para exteriores, período cálido en clima cálido seco

Directory of Open Access Journals (Sweden)

Gonzalo Bojórquez

Full Text Available El estimar las temperaturas de confort térmico en espacios exteriores permite obtener información que sirve de base para generar propuestas de diseño, cuyas condiciones ambientales propicien el confort térmico de los usuarios. Se presenta la estimación de temperatura neutral y rangos de confort térmico para espacios exteriores de un parque recreativo, en el período cálido en un clima desértico. El estudio fue desarrollado en Mexicali, Baja California, México. Se diseñó un cuestionario basado en la escala de sensaciones térmicas de ISO 10551, se midieron temperatura de bulbo seco, temperatura de globo gris, humedad relativa y velocidad de viento. Se aplicaron 822 encuestas en julio y agosto del 2008. Se estimaron temperatura neutra y rangos de confort con el método de medias por intervalo de sensación térmica. El análisis se hizo para tres niveles de actividad: pasiva, moderada e intensa y uno combinado con los tres niveles. Los valores de temperatura neutra obtenidos son aproximadamente simétricos con respecto a sus rangos de confort térmico. Las temperaturas neutras obtenidas muestran que los sujetos en actividad intensa, con práctica periódica de ejercicio y hábitos apropiados a las condiciones de clima, tienen una temperatura de confort térmico similar a aquellos con actividad pasiva.

On the electronic structure and thermoelectric properties of BiTeBr and BiTeI single crystals and of BiTeI with the addition of BiI3 and CuI

International Nuclear Information System (INIS)

Kulbachinskii, Vladimir A.; Kytin, Vladimir G.; Kudryashov, Alexey A.; Kuznetsov, Alexei N.; Shevelkov, Andrei V.

2012-01-01

The electronic structures were calculated for BiTeBr and BiTeI using the density-functional theory approach and accounting for the strong spin–orbital interaction. Qualitatively, the band structures for two compounds are similar, showing strong mixing of the p states of all elements in vicinity of the Fermi level, with the band gaps of 0.595 and 0.478 eV for BiTeBr and BiTeI, respectively. The optimized crystal structures show a tendency for the Bi–X (X=Br, I) bond elongation compared to the Bi–Te one. Both compounds are intrinsic n-type semiconductors but display a metallic-like conductivity coupled to rather large thermopower, which is rationalized within the frames of the acoustic phonons scattering model. Because of larger thermopower BiTeBr exhibits a twice higher thermoelectric figure-of-merit near room temperature, ZT=0.17, compared to BiTeI. The addition of 1 mass% of BiI 3 or CuI to BiTeI decreases the mobility of electrons by two orders of magnitude, leading to significantly lower electrical conductivity, but at the same time effectively reduces the thermal conductivity. The prospects of further enhancing the thermoelectric efficiency are briefly discussed. - Graphical abstract: View of the crystal structure of BiTeBr is shown in the figure The optimized crystal structures show a tendency for the Bi–X (X=Br, I) bond elongation compared to the Bi–Te one. The electronic structures were calculated for BiTeBr and BiTeI using the density-functional theory approach and accounting for the strong spin–orbital interaction. Qualitatively, the band structures for two compounds are similar, showing strong mixing of the p states of all elements in vicinity of the Fermi level, with the band gaps of 0.595 and 0.478 eV for BiTeBr and BiTeI, respectively. Both compounds are intrinsic n-type semiconductors but display a metallic-like conductivity coupled to rather large thermopower, which is rationalized within the frames of the acoustic phonons scattering

World Weather Extremes. Revision,

Science.gov (United States)

1985-12-01

Ext r-,ncs, Weekl Weather and Crop Bull, Vol. 43, No. 9, pp. 6-8, 27 Feb 56. 21A. ntoli, La Piu Alta Temperatura del Mondo," [The HiLhest Temperi... Temperatura in Libia", Boll Soc Geogr Ita’iana, ser. 8, Vol. 7, pp. 59-71, 1954. 23J. Gentilli, "Libyan Climate", Geograph Rev, V0 l. 45, No. 2, p. 269 S" Apr

Perfil de temperatura dos funis magnetosféricos de estrelas T Tauri com aquecimento alfvênico

Science.gov (United States)

Vasconcelos, M. J.

2003-08-01

Estrelas T Tauri Clássicas são objetos jovens circundados por discos de gás e poeira e que apresentam uma intensa atividade magnética. Seu espectro mostra linhas de emissão alargadas que são razoavelmente reproduzidas nos modelos de acresção magnetosférica. No entanto, o perfil de temperatura dos funis magnéticos é desconhecido. Aquecimento magnético compressional e difusão ambipolar foram considerados para estas estruturas, porém as temperaturas obtidas não são suficientes para explicar as observações. Neste trabalho, examinamos o aquecimento gerado pelo amortecimento de ondas Alfvén através de quatro mecanismos, os amortecimentos não-linear, turbulento, viscoso-resistivo e colisional como função da freqüência da onda. Inicialmente, a temperatura é ajustada para reproduzir as observações e o grau de turbulência requerido para que o mecanismo seja viável é calculado. Os resultados mostram que este é compatível com os dados observacionais. Apresentam-se, também, resultados preliminares do cálculo auto-consistente do perfil de temperatura dos funis, levando-se em conta fontes de aquecimento Alfvênica e fontes de resfriamento.

Influencia de la aplicación de ultra alta presión de homogeneización (UAPH y de la [Ca++] en la estabilidad de la leche de arroz

Directory of Open Access Journals (Sweden)

Santiago Jorcín

2013-01-01

Full Text Available Se analizaron bebidas de arroz sometidas a diferentes tratamientos térmicos y a UAPH. Se midió su tamaño de partícula y se correlacionó con medidas de estabilidad; se observó que las muestras procesadas por UAPH tienen una estabilidad significativamente mayor.Se estudió la interacción entre micronutrientes (Ca++ y las proteínas de la bebida y se halló que al aumentar la concentración de Ca++ la estabilidad de la bebida disminuye hasta alcanzar 80 ppm de Ca++, a partir de la cual se mantiene constante. Los recuentos de mesófilos aerobios totales, esporas, Bacillus Cereus y Enterobacteriaceaes para muestras tratadas por UAPH (temperatura de entrada 85 ºC, 300MPa temperatura en válvula 135 ºC y UAT (142 ºC 6 seg muestran una supervivencia menor a 1 UFC/mL en ambos tratamientos para todos los recuentos. Se incubaron las muestras UAPH y UAT a 30 ºC durante dos semanas sin desarrollo microbiano o alteración alguna. El proceso de ultra alta presión de homogeneización (UAPH demostró ser una tecnología válida para estabilizar y preservar la leche de arroz al reducir el tamaño de las partículas por debajo del micrómetro, favoreciendo la estabilidad fisicoquímica de la bebida y generando, concomitantemente, una reducción de la flora alterante.

High temperature bismuth cuprate superconductors synthesis and characterization

International Nuclear Information System (INIS)

Mansori, M.; Satre, P.; Breandon, C.; Roubin, M.; Sebaoun, A.

1993-01-01

High temperature superconductor phases synthesis by coprecipitation in alkaline solution is reported. (Bi 1.6 Pb 0.4 )Sr 2 Ca 1 Cu 2 O 8+x and (Bi 1.6 Pb 0.4 )Sr 2 Ca 2 Cu 3 O 10+y noted (2212) and (2223) have been prepared and studied. From aqueous nitrate solutions of Bi, Pb, Sr, Ca and Cu and oxalic acid aqueous solution as well as ethylene glycol, using an organic base (the triethylamine), the pH was increased up to the path of the precipitation zone (pH = 10.5-11.2). This method assures a good granulometric homogeneity of powders. Thermal analysis and characterization of the different components produced during the synthesis have been studied by DTA (differential thermal analysis)- TGA (thermogravimetric analysis), X-ray diffraction at different temperatures and by Infrared spectroscopy with a Fourier transformation. The measurements of magnetic susceptibility for the 2212 (with and without lead) and 2223 (with lead) phases have permitted us to observe the critical temperatures of 84 K, 87 K and 114 K. (author). 29 refs., 2 figs., 4 tabs

FATORES QUE CONTROLAM A TEMPERATURA DE SUPERFÍCIE DOS SOLOS DO NOROESTE DO PARANÁ

OpenAIRE

Otávio Cristiano Montanher; Danilo Rafael Bastos Rezende Espíndola

2017-01-01

Este artigo apresenta um estudo da temperatura de superfície de solos da região noroeste do Estado do Paraná. Essa região possui duas formações rochosas predominantes: formação Caiuá (Kc) e formação Serra Geral (JKsg). Os solos que se desenvolvem sobre essas formações possuem texturas arenosas e argilosas. Formulou-se a seguinte questão: em total exposição, tais solos possuem diferentes valores de temperatura de superfície? Adicionalmente, também foi avaliado o papel térmico da cobertura vege...

Sensor de temperatura para sistemas microelectromecánicos y procedimiento de fabricación

OpenAIRE

Vázquez Villalabeitia, Manuel; Kolesar, Vladimir

2014-01-01

El objeto de la invención es un sensor de temperatura con estructura cilíndrica y constituido por un material compuesto, que comprende un núcleo metálico y al menos un recubrimiento sobre dicho núcleo metálico con la característica de presentar una asimetría radial en cualquier sección transversal de la estructura. Constituye igualmente un objeto de la presente invención un procedimiento de fabricación del sensor de temperatura basado en la solidificación rápida del núcleo metálico en el ...

Alta Capital investeerib miljardeid kroone / Raigo Neudorf

Index Scriptorium Estoniae

Neudorf, Raigo

2006-01-01

Investeerimisfirma Alta Capital nõukogu esimees Indrek Rahumaa annab ülevaate sellest, kuidas ettevõte on lühikese ajaga suutnud omandada osaluse mitmetes ettevõtetes ning suunanud neisse investeeringuid 150 miljoni euro väärtuses. Vt. samas: Osalused; Omanikud

Preparation, characterization and enhanced visible-light photocatalytic activities of BiPO4/BiVO4 composites

International Nuclear Information System (INIS)

Wu, Siyuan; Zheng, Hong; Lian, Youwei; Wu, Yiying

2013-01-01

Graphical abstract: - Highlights: • BiPO 4 /BiVO 4 composites were successfully prepared by the hydrothermal method. • BiPO 4 /BiVO 4 composites exhibited broad absorption in the visible region. • Visible-light photocatalytic activities of BiPO 4 /BiVO 4 composites were enhanced. • P/V molar ratio and pH value of the reaction affect photocatalytic activity. • The mechanism of enhanced visible-light photocatalytic activities was discussed. - Abstract: BiPO 4 /BiVO 4 composites with different P/V molar ratios were prepared by the hydrothermal method and the effect of pH values of hydrothermal reaction on photocatalytic activity of BiPO 4 /BiVO 4 composite was investigated. The photocatalysts were characterized by X-ray diffraction, field emission scanning electron microscopy, energy-dispersive spectroscopy, X-ray photoelectron spectroscopy and UV–vis diffuse reflectance spectroscopy. The photocatalytic property of BiPO 4 /BiVO 4 was evaluated by photocatalytic degradation of Methylene blue under visible light irradiation. The results showed that the photocatalytic activity of the composites was much higher than that of pure BiPO 4 and BiVO 4 . The rate constant of Methylene blue degradation over BiPO 4 /BiVO 4 (P/V molar ratio of 5:1 and hydrothermal reaction pH value of 1.5) is 1.7 times that of pure BiVO 4 . The photocatalytic activity enhancement of BiPO 4 /BiVO 4 composite is closely related to the BiVO 4 functioning as a sensitizer to adsorb visible light and the heterojunction of BiPO 4 /BiVO 4 acting as an active center for hindering the rapid recombination of electron–hole pairs during the photocatalytic reaction

Spatial profile of thermoelectric effects during Peltier pulsing in Bi and Bi/MnBi eutectic

Science.gov (United States)

Silberstein, R. P.; Larson, D. J., Jr.

1987-01-01

The spatial profile of the thermal transients that occur during and following the current pulsing associated with Peltier Interface Demarcation during directional solidification is studied. Results for pure Bi are presented in detail and compared with corresponding results for the Bi/MnBi eutectic. Significant thermal transients occur throughout the sample that can be accounted for by the Peltier effect, the Thomson effect, and Joule heating. These effects are separated and their behavior is studied as a function of time, current density, and position with respect to the solid/liquid interface.

OCORRÊNCIA E DURAÇÃO DAS TEMPERATURAS MÍNIMAS DIÁRIAS DO AR PREJUDICIAIS À FECUNDAÇÃO DAS FLORES DO ARROZ EM SANTA MARIA. RS. III: PROBABILIDADES DE OCORRÊNCIA DA DURAÇÃO DAS TEMPERATURAS BAIXAS

Directory of Open Access Journals (Sweden)

Flávio Miguel Schneider

1992-04-01

Full Text Available Utilizando os valores das temperaturas mínimas, máximas e das 21 h, hora local, dos meses de dezembro, janeiro, fevereiro e março registradas na Estação Climatológica Principal de Santa Maria, RS, determinaram-se as probabilidades de ocorrência da duração máxima de horas com temperatura do ar ≤ 10, 11, 12, 13, 14, 15, 16 e 17,0°C e de seqüências de dias consecutivos com no mínimo uma hora de duração com temperatura do ar ≤ 15, 16 e 17,0°C. Essas probabilidades foram obtidas para cada decêndio dos meses estudados. Os resultados evidenciam que o risco de ocorrência de temperaturas prejudiciais à fecundação das flores da cultura do arroz é bem menor no 2° e 3° decêndio do mês de fevereiro. Deve-se, portanto, semear e/ou escolher ciclo de cultivar de arroz que possibilite que a fase de floração ocorra durante o 2° e 3° decêndio do mês de fevereiro.

AC loss in superconducting wires operating in a wind turbine like generator

DEFF Research Database (Denmark)

Seiler, Eugen; Zirngibl, Thomas; Mijatovic, Nenad

2010-01-01

We have manufactured a small circular superconducting coil impregnated with epoxy fibreglass. The coil was wound from a Bi-2223/Ag superconducting wire and it was tested in liquid nitrogen at 77 K. Current-voltage characteristic and the AC losses of the coil were measured and compared...

State diagram of Pr-Bi system

International Nuclear Information System (INIS)

Abulkhaev, V.L.; Ganiev, I.N.

1994-01-01

By means of thermal differential analysis, X-ray and microstructural analysis the state diagram of Pr-Bi system was studied. Following intermetallic compounds were defined in the system: Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 , Pr Bi, PrBi 2 , Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 and PrBi 2 . The data analysis on Ln-Bi diagram allowed to determine the regularity of change of properties of intermetallic compounds in the line of rare earth elements of cerium subgroup.

Bienestar psicológico en personas con alta capacidad intelectual

OpenAIRE

Ramiro Olivier, Pedro; Navarro Guzmán, José I.; Menacho Jiménez, Inmaculada; López Sinoga, M. Mar; García Sedeño, Manuel A.

2016-01-01

El bienestar psicológico en las personas de alta capacidad intelectual ha sido motivo de controversia en la literatura especializada. En ocasiones se ha considerado que estas personas son más proclives a un desajuste psicológico, mientras que otras veces los resultados han sido poco concluyentes. En el presente trabajo se ha estudiado el bienestar psicológico en personas de altas capacidades intelectuales, administrando la Escala de Bienestar Psicológico a 28 participantes de edades comprendi...

Tendências na variabilidade climática sazonal e anual das temperaturas máxima e mínima do ar no Estado do Paraná

Directory of Open Access Journals (Sweden)

Rosandro Boligon Minuzzi

2011-01-01

Full Text Available O presente trabalho teve por objetivo analisar a variabilidade sazonal e anual das temperaturas máxima e mínima do ar no Estado do Paraná. A Análise de Regressão e o teste de Kendall foram utilizados para testar a tendência das médias de temperatura máxima e mínima, do número de dias com registros de temperatura inferior a 3 °C, dos eventos extremos e valores absolutos diários da temperatura máxima e mínima nas escalas sazonal (verão, outono, inverno e primavera e anual. Os pontos de descontinuidade obtidos pelo Teste de Homogeneidade Normal Padrão mostram resultados mais expressivos para a temperatura máxima anual e no outono. Para esta variável meteorológica os pontos foram obtidos predominantemente no início da década de 2000. Na temperatura máxima anual e, principalmente na temperatura mínima, em todas as escalas de tempo, houve tendência de aumento. Esse aumento relativamente maior da temperatura mínima sugere uma diminuição na amplitude térmica no Paraná. Os valores dos extremos diários da temperatura mínima estão sendo maiores, porém, menos freqüentes. Por outro lado, as temperaturas máximas têm sido mais intensas e freqüentes, especialmente na primavera.

First tests of twisted-pair HTS 1 kA range cables for use in superconducting links

CERN Document Server

Ballarino, A; Hurte, J; Sitko, M; Willering, G