Thermal expansion of Cr2xFe2-2xMo3O12, Al2xFe2-2xMo3O12 and Al2xCr2-2xMo3O12 solid solutions

International Nuclear Information System (INIS)

Ari, M.; Jardim, P.M.; Marinkovic, B.A.; Rizzo, F.; Ferreira, F.F.

2008-01-01

The transition temperature from monoclinic to orthorhombic and the thermal expansion of the orthorhombic phase were investigated for three systems of the family A 2 M 3 O 12 : Cr 2x Fe 2-2x Mo 3 O 12 , Al 2x Fe 2-2x Mo 3 O 12 and Al 2x Cr 2-2x Mo 3 O 12 . It was possible to obtain a single-phase solid solution in all studied samples (x=0, 0.1, 0.3, 0.5, 0.7, 0.9 and 1). A linear relationship between the transition temperature and the fraction of A 3+ cations (x) was observed for each system. In all orthorhombic solid solutions studied here the observed thermal expansion was anisotropic. These anisotropic thermal expansion properties of crystallographic axes a, b and c result in a low positive or near-zero overall linear coefficient of thermal expansion (α l =α V /3). The relationship between the size of A 3+ cations in A 2 M 3 O 12 and the coefficient of thermal expansion is discussed. Near-zero thermal expansion of Cr 2 Mo 3 O 12 is explained by the behavior of Cr-O and Mo-O bond distances, Cr-Mo non-bond distances and Cr-O-Mo bond angles with increasing temperature, estimated by Rietveld analysis of synchrotron X-ray powder diffraction data. - Graphical abstract: In this figure, all published overall linear coefficients of thermal expansion for orthorhombic A 2 M 3 O 12 family obtained through diffraction methods as a function of A 3+ cation radii size, together with dilatometric results, are plotted. Our results indicate that Cr 2 Mo 3 O 12 does not exactly follow the established relationship

Behaviour of Fe4O5-Mg2Fe2O5 solid solutions and their relation to coexisting Mg-Fe silicates and oxide phases

Science.gov (United States)

Uenver-Thiele, Laura; Woodland, Alan B.; Miyajima, Nobuyoshi; Ballaran, Tiziana Boffa; Frost, Daniel J.

2018-03-01

Experiments at high pressures and temperatures were carried out (1) to investigate the crystal-chemical behaviour of Fe4O5-Mg2Fe2O5 solid solutions and (2) to explore the phase relations involving (Mg,Fe)2Fe2O5 (denoted as O5-phase) and Mg-Fe silicates. Multi-anvil experiments were performed at 11-20 GPa and 1100-1600 °C using different starting compositions including two that were Si-bearing. In Si-free experiments the O5-phase coexists with Fe2O3, hp-(Mg,Fe)Fe2O4, (Mg,Fe)3Fe4O9 or an unquenchable phase of different stoichiometry. Si-bearing experiments yielded phase assemblages consisting of the O5-phase together with olivine, wadsleyite or ringwoodite, majoritic garnet or Fe3+-bearing phase B. However, (Mg,Fe)2Fe2O5 does not incorporate Si. Electron microprobe analyses revealed that phase B incorporates significant amounts of Fe2+ and Fe3+ (at least 1.0 cations Fe per formula unit). Fe-L2,3-edge energy-loss near-edge structure spectra confirm the presence of ferric iron [Fe3+/Fetot = 0.41(4)] and indicate substitution according to the following charge-balanced exchange: [4]Si4+ + [6]Mg2+ = 2Fe3+. The ability to accommodate Fe2+ and Fe3+ makes this potential "water-storing" mineral interesting since such substitutions should enlarge its stability field. The thermodynamic properties of Mg2Fe2O5 have been refined, yielding H°1bar,298 = - 1981.5 kJ mol- 1. Solid solution is complete across the Fe4O5-Mg2Fe2O5 binary. Molar volume decreases essentially linearly with increasing Mg content, consistent with ideal mixing behaviour. The partitioning of Mg and Fe2+ with silicates indicates that (Mg,Fe)2Fe2O5 has a strong preference for Fe2+. Modelling of partitioning with olivine is consistent with the O5-phase exhibiting ideal mixing behaviour. Mg-Fe2+ partitioning between (Mg,Fe)2Fe2O5 and ringwoodite or wadsleyite is influenced by the presence of Fe3+ and OH incorporation in the silicate phases.

Moessbauer spectroscopy study of the synthesis of SnFe2O4 by high energy ball milling (HEBM) of SnO and α-Fe2O3

International Nuclear Information System (INIS)

Uwakweh, Oswald N C; Perez Moyet, Richard; Mas, Rita; Morales, Carolyn; Vargas, Pedro; Silva, Josue; Rossa, Angel; Lopez, Neshma

2010-01-01

The formation of single phase nanoparticles of spinel structured ferrite, SnFe 2 O 4 , by mechanochemical syntheses using HEBM of stoichiometric amounts of solid SnO and α-Fe 2 O 3 with acetone as surfactant was achieved progressively as function of ball milling time. Single phase SnFe 2 O 4 formation commenced from five hours of continuous ball milling, and reached completion after 22 hours, thereby yielding a material with a lattice parameter of 8.543 A, and particle size of 10.91 nm. The coercivity was 4.44 mT, magnetic saturation value of 17.75 Am 2 /kg, and remanent magnetizations of 1.50 Am 2 /kg, correspondingly. The nanosized particles exhibited superparamagnetic behavior phenomenon based on Moessbauer spectroscopy measurements. The kinetic analyses based on the modified Kissinger method yielded four characteristic stages during the thermal evolution of the 22 hours milled state with activation energies of 0.23 kJ/mol, 2.52 kJ/mol, 0.024 kJ/mol, and 1.57 kJ/mol respectively.

Magnetically diluted semi-conductor of SnO_2- Fe obtained by controlled precipitation

International Nuclear Information System (INIS)

Cajas, P.C.; Munoz, R.; Rodriguez-Paez, J.E.

2014-01-01

Solid solutions were synthesized SnO_2 doped with 5% and 8 mol% Fe by the controlled precipitation method. The particles size was obtained of ∼12 nm with heath treatment 450 °C. The presence of iron in the structure is evidenced by Raman spectroscopy The crystallite size we obtained with the results of XRD, and particle size by MET, it was concluded that the nanoparticles obtained were monocrystalline. The particles were characterized magnetically, for the powders doped to 8% Fe was determined ferromagnetic behavior at 5K, with a tendency superparamagnetic and paramagnetic at a temperature of 300K. (author)

Morphological and humidity sensing characteristics of SnO 2 –CuO ...

Indian Academy of Sciences (India)

This paper reports the synthesis of SnO2–CuO, SnO2–Fe2O3 and SnO2–SbO2 composites of nano oxides and comparative study of humidity sensing on their electrical resistances. CuO, Fe2O3 and SbO2 were added within base material SnO2 in the ratio 1 : 0.25, 1 : 0.50 and 1 : 1. Characterizations of materials were done ...

Characterisation of a tertiary mixture of {alpha}-Fe{sub 2}O{sub 3}, {gamma}-Fe{sub 2}O{sub 3} and Fe{sub 3}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Srinivasan, M.P.; Narasimhan, S.V. [Water and Steam Chemistry Laboratory (Chemistry Group, BARC) BARC Facilities, Kalpakkam, Tamil Nadu 603 102. (India)

1998-12-31

A method has been developed to quantify the individual components of a ternary mixture containing {alpha}-Fe{sub 2}O{sub 3}, {gamma}- Fe{sub 2}O{sub 3} and Fe{sub 3}O{sub 4} based on the preferential dissolution of the components at a fixed time (fixed time - depending on the strength of the chelating agent) in a dilute chemical formulation (containing a chelant and an organic acid) both in presence and absence of reductant. A ternary component diagram was constructed based on the percentage dissolution of the individual components in 2,6-Pyridine dicarboxylic acid (PDCA), Nitrilo triacetic acid (NTA) and EDTA based formulation at 60degC both in presence and absence of reductant. In these formulations, the observed behaviour that the {alpha}-Fe{sub 2}O{sub 3} dissolved very little both in presence and absence of reductant and {gamma}-Fe{sub 2}O{sub 3} dissolved very little in absence of reductant were used for resolving the ternary physical mixture composition. Physical mixtures of Fe{sub 3}O{sub 4}, {alpha}-Fe{sub 2}O{sub 3} and {gamma}-Fe{sub 2}O{sub 3} based on mole ratio were taken such that the total quantity of Fe present would be 1.37 mM for complete dissolution. In presence and absence of reductant, dissolution percentage of Fe observed at fixed time in these formulations, when fit into the already constructed three component phase diagram for each formulation at the same fixed duration, the experimentally resolved composition showed good agreement with that based on individual components. This method is useful to resolve different polymorphs of metal oxides having the metal ions in single and/or multiple oxidation states. (author)

Facile synthesis and characterization of ZnFe{sub 2}O{sub 4}/{alpha}-Fe{sub 2}O{sub 3} composite hollow nanospheres

Energy Technology Data Exchange (ETDEWEB)

Shen, Yu [Key Laboratory of Industrial Ecology and Environmental Engineering and State Key Laboratory of Fine Chemical, School of Environmental Science and Technology, Dalian University of Technology, Dalian 116024 (China); School of Environmental and Chemical Engineering, Dalian Jiaotong University, Dalian 116028 (China); Li, Xinyong, E-mail: xyli@dlut.edu.cn [Key Laboratory of Industrial Ecology and Environmental Engineering and State Key Laboratory of Fine Chemical, School of Environmental Science and Technology, Dalian University of Technology, Dalian 116024 (China); Department of Chemical Engineering, Curtin University, Perth, WA 6845 (Australia); Zhao, Qidong; Hou, Yang [Key Laboratory of Industrial Ecology and Environmental Engineering and State Key Laboratory of Fine Chemical, School of Environmental Science and Technology, Dalian University of Technology, Dalian 116024 (China); Tade, Moses [Department of Chemical Engineering, Curtin University, Perth, WA 6845 (Australia); Liu, Shaomin, E-mail: Shaomin.Liu@curtin.edu.au [Department of Chemical Engineering, Curtin University, Perth, WA 6845 (Australia)

2011-12-15

Highlights: Black-Right-Pointing-Pointer ZnFe{sub 2}O{sub 4}/{alpha}-Fe{sub 2}O{sub 3} composite hollow nanospheres were successfully synthesized via a facile method. Black-Right-Pointing-Pointer Detailed structural, morphology and the phase composition were studied. Black-Right-Pointing-Pointer The incorporation of ZnFe{sub 2}O{sub 4} and {alpha}-Fe{sub 2}O{sub 3} gives an appropriate band gap value to utilize solar energy. -- Abstract: ZnFe{sub 2}O{sub 4}/{alpha}-Fe{sub 2}O{sub 3} composite hollow nanospheres were successfully fabricated via a facile one-pot solvothermal method, utilizing polyethylene glycol as soft template. X-ray diffraction and scanning electron microscopy analysis revealed that the prepared nanospheres with cubic spinel and rhombohedra composite structure had a uniform diameter of about 370 nm, and the hollow structure could be further confirmed by transmission electron microscopy. Energy dispersive X-ray, X-ray photoelectron spectroscopy and Fourier transform infrared techniques were also applied to characterize the elemental composition and chemical bonds in the hollow nanospheres. The ZnFe{sub 2}O{sub 4}/{alpha}-Fe{sub 2}O{sub 3} composite hollow nanospheres show attractive light absorption property for potential applications in electronics, optics, and catalysis.

Fabrication, characterization, and photocatalytic property of {alpha}-Fe{sub 2}O{sub 3}/graphene oxide composite

Energy Technology Data Exchange (ETDEWEB)

Li Hong; Zhao Qidong; Li Xinyong, E-mail: xinyongli@hotmail.com [School of Environmental Science and Technology, Dalian University of Technology, State Key Laboratory of Fine Chemical, Key Laboratory of Industrial Ecology and Environmental Engineering (MOE) (China); Zhu Zhengru [Research Center of Hydrology and Engineering, Academy of City and Environment, Liaoning Normal University (China); Tade, Moses; Liu Shaomin, E-mail: shaomin.liu@curtin.edu.au [Curtin University, Department of Chemical Engineering (Australia)

2013-06-15

Spindle-shaped microstructure of {alpha}-Fe{sub 2}O{sub 3} was successfully synthesized by a simple hydrothermal method. The {alpha}-Fe{sub 2}O{sub 3}/graphene oxide (GO) composites was prepared using a modified Hummers' strategy. The properties of the samples were systematically investigated by X-ray powder diffraction (XRD), UV-Vis diffuse reflectance spectrophotometer, transmission electron microscope, atomic force microscope, X-ray photoelectron spectroscopy, and Raman spectroscopy (Raman) techniques. GO nanosheets act as supporting materials for anchoring the {alpha}-Fe{sub 2}O{sub 3} particles. The average crystallite sizes of the {alpha}-Fe{sub 2}O{sub 3} and {alpha}-Fe{sub 2}O{sub 3}/GO samples are ca. 27 and 24 nm, respectively. The possible growth of {alpha}-Fe{sub 2}O{sub 3} onto GO layers led to a higher absorbance capacity for visible light by {alpha}-Fe{sub 2}O{sub 3}/GO than {alpha}-Fe{sub 2}O{sub 3} composite. The photocatalytic degradation of toluene over the {alpha}-Fe{sub 2}O{sub 3} and {alpha}-Fe{sub 2}O{sub 3}/GO samples under xenon-lamp irradiation was comparatively studied by in situ FTIR technique. The results indicate that the {alpha}-Fe{sub 2}O{sub 3}/GO sample synthesized exhibited a higher capacity for the degradation of toluene. The composite of {alpha}-Fe{sub 2}O{sub 3}/GO could be promisingly applied in photo-driven air purification.

Shape Engineering Driven by Selective Growth of SnO2 on Doped Ga2O3 Nanowires.

Science.gov (United States)

Alonso-Orts, Manuel; Sánchez, Ana M; Hindmarsh, Steven A; López, Iñaki; Nogales, Emilio; Piqueras, Javier; Méndez, Bianchi

2017-01-11

Tailoring the shape of complex nanostructures requires control of the growth process. In this work, we report on the selective growth of nanostructured tin oxide on gallium oxide nanowires leading to the formation of SnO 2 /Ga 2 O 3 complex nanostructures. Ga 2 O 3 nanowires decorated with either crossing SnO 2 nanowires or SnO 2 particles have been obtained in a single step treatment by thermal evaporation. The reason for this dual behavior is related to the growth direction of trunk Ga 2 O 3 nanowires. Ga 2 O 3 nanowires grown along the [001] direction favor the formation of crossing SnO 2 nanowires. Alternatively, SnO 2 forms rhombohedral particles on [110] Ga 2 O 3 nanowires leading to skewer-like structures. These complex oxide structures were grown by a catalyst-free vapor-solid process. When pure Ga and tin oxide were used as source materials and compacted powders of Ga 2 O 3 acted as substrates, [110] Ga 2 O 3 nanowires grow preferentially. High-resolution transmission electron microscopy analysis reveals epitaxial relationship lattice matching between the Ga 2 O 3 axis and SnO 2 particles, forming skewer-like structures. The addition of chromium oxide to the source materials modifies the growth direction of the trunk Ga 2 O 3 nanowires, growing along the [001], with crossing SnO 2 wires. The SnO 2 /Ga 2 O 3 junctions does not meet the lattice matching condition, forming a grain boundary. The electronic and optical properties have been studied by XPS and CL with high spatial resolution, enabling us to get both local chemical and electronic information on the surface in both type of structures. The results will allow tuning optical and electronic properties of oxide complex nanostructures locally as a function of the orientation. In particular, we report a dependence of the visible CL emission of SnO 2 on its particular shape. Orange emission dominates in SnO 2 /Ga 2 O 3 crossing wires while green-blue emission is observed in SnO 2 particles attached to Ga 2

Synthesis and structure of a pink pigment in the system Zr02-TiO2-SnO2-Cr2O3

International Nuclear Information System (INIS)

Zygadlo, M.

1979-01-01

The mechanism has been discussed of the formation of this pigment in the ceramic glazes and the results are communicated of the experiment to synthetize this pigment and to test it by the thermographic, X-ray and electron-microsonde methods. It has been found that the pink pigment is the result of dispersion of Cr 2 O 3 upon the grain areas of Zr0 2 , TiO 2 and SnO 2 : it is not a solid solution of Cr 2 O 3 in these oxides as has been earlier suggested. (author)

Thick Fe2O3, Fe3O4 films prepared by the chemical solution deposition method

Czech Academy of Sciences Publication Activity Database

Buršík, Josef; Košovan, P.; Šubrt, Jan

2006-01-01

Roč. 39, č. 2 (2006), s. 85-94 ISSN 0928-0707 R&D Projects: GA ČR GA203/01/0408 Institutional research plan: CEZ:AV0Z40320502 Keywords : chemical solution deposition * thick films * alpha-Fe2O3 Subject RIV: CA - Inorganic Chemistry Impact factor: 1.009, year: 2006

Thermal behavior of the amorphous precursors of the ZrO2-SnO2 system

International Nuclear Information System (INIS)

Stefanic, Goran; Music, Svetozar; Ivanda, Mile

2008-01-01

Thermal behavior of the amorphous precursors of the ZrO 2 -SnO 2 system on the ZrO 2 -rich side of the concentration range, prepared by co-precipitation from aqueous solutions of the corresponding salts, was monitored using differential thermal analysis, X-ray powder diffraction, Raman spectroscopy, field emission scanning electron microscopy (FE-SEM) and energy dispersive X-ray spectrometry (EDS). The crystallization temperature of the amorphous precursors increased with an increase in the SnO 2 content, from 405 deg. C (0 mol% SnO 2 ) to 500 deg. C (40 mol% SnO 2 ). Maximum solubility of Sn 4+ ions in the ZrO 2 lattice (∼25 mol%) occurred in the metastable products obtained upon crystallization of the amorphous precursors. A precise determination of unit-cell parameters, using both Rietveld and Le Bail refinements of the powder diffraction patterns, shows that the incorporation of Sn 4+ ions causes an asymmetric distortion of the monoclinic ZrO 2 lattice. The results of phase analysis indicate that the incorporation of Sn 4+ ions has no influence on the stabilization of cubic ZrO 2 and negligible influence on the stabilization of tetragonal ZrO 2 . Partial stabilization of tetragonal ZrO 2 in products having a tin content above its solid-solubility limit was attributed to the influence of ZrO 2 -SnO 2 surface interactions. In addition to phases closely structurally related to cassiterite, monoclinic ZrO 2 and tetragonal ZrO 2 , a small amount of metastable ZrSnO 4 phase appeared in the crystallization products of samples with 40 and 50 mol% of SnO 2 calcined at 1000 deg. C. Further temperature treatments caused a decrease in and disappearance of metastable phases. The results of the micro-structural analysis show that the sinterability of the crystallization products significantly decreases with an increase in the SnO 2 content

In situ observation of transformation in alpha-Fe sub 2 O sub 3 under hydrogen implantation

CERN Document Server

Watanabe, Y; Ishikawa, N; Furuya, K; Kato, M

2002-01-01

An in situ observation of the alpha-Fe sub 2 O sub 3 -to-Fe sub 3 O sub 4 transformation has been performed using a dual-ion-beam accelerator interfaced with a transmission electron microscope (TEM). During the hydrogen-ion implantation of alpha-Fe sub 2 O sub 3 , transformation into the new phase (gamma-Fe sub 2 O sub 3 or Fe sub 3 O sub 4) was observed. It was also found that the orientation relationship between alpha-Fe sub 2 O sub 3 and the new phase (gamma-Fe sub 2 O sub 3 or Fe sub 3 O sub 4) satisfies the Shoji-Nishiyama relationship, in agreement with previous experiments. It was also found that the nearest interatomic distance does not vary by the implantation until the re-stacked phase appears, although when the re-stacked phase is formed, the lattice expansion is observed in the transformed (re-stacked) phase. Judging from these results, we have concluded that the alpha-Fe sub 2 O sub 3 to Fe sub 3 O sub 4 transformation is induced during the hydrogen ion implantation of alpha-Fe sub 2 O sub 3.

Field emission from patterned SnO2 nanostructures

International Nuclear Information System (INIS)

Zhang Yongsheng; Yu Ke; Li Guodong; Peng Deyan; Zhang Qiuxiang; Hu Hongmei; Xu Feng; Bai Wei; Ouyang Shixi; Zhu Ziqiang

2006-01-01

A simple and reliable method has been developed for synthesizing finely patterned tin dioxide (SnO 2 ) nanostructure arrays on silicon substrates. A patterned Au catalyst film was prepared on the silicon wafer by radio frequency (RF) magnetron sputtering and photolithographic patterning processes. The patterned SnO 2 nanostructures arrays, a unit area is of ∼500 μm x 200 μm, were synthesized via vapor phase transport method. The surface morphology and composition of the as-synthesized SnO 2 nanostructures were characterized by means of scanning electron microscopy (SEM) and X-ray diffraction (XRD). The mechanism of formation of SnO 2 nanostructures was also discussed. The measurement of field emission (FE) revealed that the as-synthesized SnO 2 nanorods, nanowires and nanoparticles arrays have a lower turn-on field of 2.6, 3.2 and 3.9 V/μm, respectively, at the current density of 0.1 μA/cm 2 . This approach must have a wide variety of applications such as fabrications of micro-optical components and micropatterned oxide thin films used in FE-based flat panel displays, sensor arrays and so on

Kinetics of dissolution of {alpha}-Fe{sub 2}O{sub 3} and {gamma}-Fe{sub 2}O{sub 3} in EDTA and NTA-based formulations

Energy Technology Data Exchange (ETDEWEB)

Ranganathan, S. [Dept. of Chemical Engineering, Univ. of New Brunswick, Fredericton, N.B. (Canada); Srinivasan, M.P. [Water and Steam Chemistry Lab. of Bhabha Atomic Research Centre (BARC) (India); Narasimhan, S.V. [Bhabha Atomic Research Centre (India); Raghavan, P.S. [Madras Christian Coll., Chennai (India); Gopalan, R. [Dept. of Chemistry, Madras Christian Coll., Chennai (India)

2004-06-01

The dissolution studies were carried out on haematite ({alpha}-Fe{sub 2}O{sub 3}) and maghemite ({gamma}-Fe{sub 2}O{sub 3}) in two different formulations of ethylenediaminetetraacetic acid (EDTA) and nitrilotriaceticacid (NTA). The rate constants were calculated using the ''inverse cubic rate law.'' The leaching of the metal ions from the oxide is controlled partly by the Fe(II)-L{sub n} (L is a complexing ligand and n is the number of ligands attached to Fe{sup 2+}), a dissolution product arising from the oxides having Fe{sup 2+} in the lattice. The addition of Fe(II)-L{sub n} along with the formulation greatly increased the initial rate of dissolution. The effect of the addition of Fe(II)-L as a reductant on the dissolution of {alpha}-Fe{sub 2}O{sub 3} was not the same as in the case of {gamma}-Fe{sub 2}O{sub 3}. The rate constants (k{sub obs}) for the dissolution of {alpha}-Fe{sub 2}O{sub 3} and {gamma}-Fe{sub 2}O{sub 3} in the presence of ascorbic acid were less in the EDTA formulation than in the NTA formulation. The studies using Fe(II)-NTA and Fe(II)-EDTA with varying compositions of citric acid and ascorbic acid revealed that a minimum quantity of the chelant is sufficient to initiate the dissolution process, which can be further controlled by the reductants and weaker chelants such as citric acid. (orig.)

Improvement of H2S Sensing Properties of SnO2-Based Thick Film Gas Sensors Promoted with MoO3 and NiO

Directory of Open Access Journals (Sweden)

In Sung Son

2013-03-01

Full Text Available The effects of the SnO2 pore size and metal oxide promoters on the sensing properties of SnO2-based thick film gas sensors were investigated to improve the detection of very low H2S concentrations (<1 ppm. SnO2 sensors and SnO2-based thick-film gas sensors promoted with NiO, ZnO, MoO3, CuO or Fe2O3 were prepared, and their sensing properties were examined in a flow system. The SnO2 materials were prepared by calcining SnO2 at 600, 800, 1,000 and 1,200 °C to give materials identified as SnO2(600, SnO2(800, SnO2(1000, and SnO2(1200, respectively. The Sn(12Mo5Ni3 sensor, which was prepared by physically mixing 5 wt% MoO3 (Mo5, 3 wt% NiO (Ni3 and SnO2(1200 with a large pore size of 312 nm, exhibited a high sensor response of approximately 75% for the detection of 1 ppm H2S at 350 °C with excellent recovery properties. Unlike the SnO2 sensors, its response was maintained during multiple cycles without deactivation. This was attributed to the promoter effect of MoO3. In particular, the Sn(12Mo5Ni3 sensor developed in this study showed twice the response of the Sn(6Mo5Ni3 sensor, which was prepared by SnO2(600 with the smaller pore size than SnO2(1200. The excellent sensor response and recovery properties of Sn(12Mo5Ni3 are believed to be due to the combined promoter effects of MoO3 and NiO and the diffusion effect of H2S as a result of the large pore size of SnO2.

Disappearance of superconductivity in the solid solution between (Ca4Al2O6)(Fe2As2) and (Ca4Al2O6)(Fe2P2) superconductors.

Science.gov (United States)

Shirage, Parasharam M; Kihou, Kunihiro; Lee, Chul-Ho; Takeshita, Nao; Eisaki, Hiroshi; Iyo, Akira

2012-09-19

The effect of alloying the two perovskite-type iron-based superconductors (Ca(4)Al(2)O(6))(Fe(2)As(2)) and (Ca(4)Al(2)O(6))(Fe(2)P(2)) was examined. While the two stoichiometric compounds possess relatively high T(c)'s of 28 and 17 K, respectively, their solid solutions of the form (Ca(4)Al(2)O(6))(Fe(2)(As(1-x)P(x))(2)) do not show superconductivity over a wide range from x = 0.50 to 0.95. The resultant phase diagram is thus completely different from those of other typical iron-based superconductors such as BaFe(2)(As,P)(2) and LaFe(As,P)O, in which superconductivity shows up when P is substituted for As in the non-superconducting "parent" compounds. Notably, the solid solutions in the non-superconducting range exhibit resistivity anomalies at temperatures of 50-100 K. The behavior is reminiscent of the resistivity kink commonly observed in various non-superconducting parent compounds that signals the onset of antiferromagnetic/orthorhombic long-range order. The similarity suggests that the suppression of the superconductivity in the present case also has a magnetic and/or structural origin.

Photocatalytic hydrogen production over solid solutions between BiFeO{sub 3} and SrTiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Lu, Lingwei; Lv, Meilin [Shanghai Key Lab of Chemical Assessment and Sustainability, Department of Chemistry, Tongji University, 1239 Siping Road, Shanghai, 200092 (China); Liu, Gang [Shenyang National laboratory for Materials Science, Institute of Metal Research, Chinese Academy of Science, 72 Wenhua Road, Shenyang 110016 (China); Xu, Xiaoxiang, E-mail: xxxu@tongji.edu.cn [Shanghai Key Lab of Chemical Assessment and Sustainability, Department of Chemistry, Tongji University, 1239 Siping Road, Shanghai, 200092 (China)

2017-01-01

Graphical abstract: We have successfully prepared a series of SrTiO{sub 3}-BiFeO{sub 3} solid solutions. These materials own strong visible light absorption and demonstrate appealing photocatalytic activity under both full range and visible light irradiation. - Highlights: • Band gap values can be tuned by adjusting molar ratios between SrTiO{sub 3} and BiFeO{sub 3}. • Photocatalytic activity is greatly improved after constituting solid solutions. • Photocatalytic activity is influenced by surface area and light absorption. • Fe plays an important role for band gap reduction and catalytic activity. - Abstract: Constituting solid solutions has been an appealing means to gain control over various physicochemical properties. In this work, we synthesized a series of SrTiO{sub 3}-BiFeO{sub 3} solid solutions and systematically explored their structural, optical and photocatalytic properties. Our results show that all solid solutions crystallize in a primitive cubic structure and their band gap values can be easily tuned by adjusting molar ratios between SrTiO{sub 3} and BiFeO{sub 3}. Photocatalytic hydrogen production under both full range and visible light irradiation is greatly improved after forming solid solutions. The highest hydrogen production rate obtained is ∼180 μmol/h under full range irradiation (λ ≥ 250 nm) and ∼4.2 μmol/h under visible light irradiation (λ ≥ 400 nm), corresponding to apparent quantum efficiency ∼2.28% and ∼0.10%, respectively. The activity is found to be strongly influenced by surface area and light absorption. Theoretical calculation suggests that Fe contributes to the formation of spin-polarized bands in the middle of original band gap and is responsible for the band gap reduction and visible light photocatalytic activity.

Multiferroic properties in NdFeO3-PbTiO3 solid solutions

Science.gov (United States)

Kumar, Sunil; Pal, Jaswinder; Kaur, Shubhpreet; Agrawal, P.; Singh, Mandeep; Singh, Anupinder

2018-05-01

The x(NdFeO3) - 1-x(PbTiO3) where x = 0.2 solid solution was prepared using solid state reaction route. The X-ray diffraction (XRD) data reveals the single phase formation. The microstructure shows grain growth with lesser porosity. The energy dispersive analysis confirms the presence of elements in stochiometric proportion. The polarization vs. Electric field loop estabilished a ferroelectric type behavior but lossy in nature. This lossy nature may be due to the presence of large leakage current in solid solution. The Magnetization vs. Magnetic field plot exhibits a unsaturated hysteriss loop indicates that the sample is not purely ferromagnetic.

Formation of high-conductivity regions in SnO2-AOx (A - Ti4+, Zr4+, Sb3+, Sb5+) films exposed to ultraviolet radiation of H2

International Nuclear Information System (INIS)

Postovalova, G.G.; Roginskaya, Yu.E.; Zav'yalov, S.A.; Galyamov, B.Sh.; Klimasenko, N.L.

2000-01-01

Composition, structure and electron properties of SnO 2 films doped by Ti, Zr and Sb oxides were studied. The doped SnO 2 films were determined to contain nano-regions of SnO 2 base crystalline solid solutions and amorphous SnO 2 containing Sn 2+ or Sb 3+ ions and residing at the surface of crystallites or between them. These composition and structure peculiarities affect essentially both electron structure and electrical properties of films. Localized 5s-states of the conductivity range diffused boundary of amorphous SnO 2 partially filled with 5s-electrons of Sn 2+ or Sb 3+ ions serving as traps capture free electrons in the crystalline ranges and motivate high resistance of films [ru

Ultraviolet emission from low resistance Cu2SnS3/SnO2 and CuInS2/Sn:In2O3 nanowires

Directory of Open Access Journals (Sweden)

E. Karageorgou

2014-11-01

Full Text Available SnO2 and Sn:In2O3 nanowires were grown on Si(001, and p-n junctions were fabricated in contact with p-type Cu2S which exhibited rectifying current–voltage characteristics. Core-shell Cu2SnS3/SnO2 and CuInS2/Sn:In2O3 nanowires were obtained by depositing copper and post-growth processing under H2S between 100 and 500 °C. These consist mainly of tetragonal rutile SnO2 and cubic bixbyite In2O3. We observe photoluminescence at 3.65 eV corresponding to band edge emission from SnO2 quantum dots in the Cu2SnS3/SnO2 nanowires due to electrostatic confinement. The Cu2SnS3/SnO2 nanowires assemblies had resistances of 100 Ω similar to CuInS2/In2O3 nanowires which exhibited photoluminescence at 3.0 eV.

SnO2/PPy Screen-Printed Multilayer CO2 Gas Sensor

Directory of Open Access Journals (Sweden)

S.A. WAGHULEY

2007-05-01

Full Text Available Tin dioxide (SnO2 plays a dominant role in solid state gas sensors and exhibit sensitivity towards oxidizing and reducing gases by a variation of its electrical properties. The electrical conducting polymer-polypyrrole (PPy has high anisotropy of electrical conduction and used as a gas sensor. SnO2/PPy multilayer, pure SnO2, pure PPy sensors were prepared by screen-printing method on Al2O3 layer followed by glass substrate. The sensors were used for different concentration (ppm of CO2 gas investigation at room temperature (303 K. The sensitivity of SnO2/PPy multilayer sensor was found to be higher, compared with pure SnO2 and pure PPy sensors. The multilayer sensor exhibited improved stability. The response and recovery time of multilayer sensor were found to be ~2 min and ~10 min respectively.

Electrochemical and optical properties of CeO2-SnO2 and CeO2-SnO2:X (X = Li, C, Si films

Directory of Open Access Journals (Sweden)

Berton Marcos A.C.

2001-01-01

Full Text Available Thin solid films of CeO2-SnO2 (17 mol% Sn and CeO2-SnO2:X (X = Li, C and Si were prepared by the sol-gel route, using an aqueous-based process. The addition of Li, C and Si to the precursor solution leads to films with different electrochemical performances. The films were deposited by the dip-coating technique on ITO coated glass (Donnelly Glass at a speed of 10 cm/min and submitted to a final thermal treatment at 450 °C during 10 min in air. The electrochemical and optical properties of the films were determined from the cyclic voltammetry and chronoamperometry measurements using 0.1 M LiOH as supporting electrolyte. The ion storage capacity of the films was investigated using in situ spectroelectrochemical method and during the insertion/extraction process the films remained transparent. The powders were characterized by thermal analysis (DSC/TGA and X-ray diffraction.

Synthesis and properties of γ-Ga2O3-Al2O3 solid solutions

Science.gov (United States)

Afonasenko, T. N.; Leont'eva, N. N.; Talzi, V. P.; Smirnova, N. S.; Savel'eva, G. G.; Shilova, A. V.; Tsyrul'nikov, P. G.

2017-10-01

The textural and structural properties of mixed oxides Ga2O3-Al2O3, obtained via impregnating γ-Al2O3 with a solution of Ga(NO3)3 and subsequent heat treatment, are studied. According to the results from X-ray powder diffraction, gallium ions are incorporated into the structure of aluminum oxide to form a solid solution of spinel-type γ-Ga2O3-Al2O3 up to a Ga2O3 content of 50 wt % of the total weight of the sample, accompanied by a reduction in the specific surface area, volume, and average pore diameter. It is concluded that when the Ga2O3 content exceeds 50 wt %, the β-Ga2O3 phase is observed along with γ-Ga2O3-Al2O3 solid solution. 71Ga and 27Al NMR spectroscopy shows that gallium replaces aluminum atoms from the tetrahedral position to the octahedral coordination in the structure of γ-Ga2O3-Al2O3.

Surface structure of alpha-Fe sub 2 O sub 3 nanocrystal observed by O K-edge X-ray absorption spectroscopy

CERN Document Server

Zhang, J; Ibrahim, K; Abbas, M I; Ju, X

2003-01-01

X-ray absorption near edge structure (XANES) spectra is used as a probe of surface structure of alpha-Fe sub 2 O sub 3 nanocrystal, prepared by sol-gel method. We present O K-edge XANES of alpha-Fe sub 2 O sub 3 in nanocrystal and bulk by total electron yield at the photoemission station of Beijing Synchrotron Radiation Facility. The spectrum of alpha-Fe sub 2 O sub 3 shows a splitting of the pre-edge structure, which is interpreted as two subsets of Fe 3d t sub 2 sub g and e sub g orbitals in oxygen octahedral (O sub h) crystal field, and is also sensitive to long-range order effects. However, no distinguishable splitting of the pre-edge peak of nanocrystal alpha-Fe sub 2 O sub 3 is observed. This suggests that there exists the distorted octahedral coordination around Fe sites and also the long-range disorder due to the surface as compared with bulk alpha-Fe sub 2 O sub 3.

TiO2 coated SnO2 nanosheet films for dye-sensitized solar cells

International Nuclear Information System (INIS)

Cai Fengshi; Yuan Zhihao; Duan Yueqing; Bie Lijian

2011-01-01

TiO 2 -coated SnO 2 nanosheet (TiO 2 -SnO 2 NS) films about 300 nm in thickness were fabricated on fluorine-doped tin oxide glass by a two-step process with facile solution-grown approach and subsequent hydrolysis of TiCl 4 aqueous solution. The as-prepared TiO 2 -SnO 2 NSs were characterized by scanning electron microscopy and X-ray diffraction. The performances of the dye-sensitized solar cells (DSCs) with TiO 2 -SnO 2 NSs were analyzed by current-voltage measurements and electrochemical impedance spectroscopy. Experimental results show that the introduction of TiO 2 -SnO 2 NSs can provide an efficient electron transition channel along the SnO 2 nanosheets, increase the short current density, and finally improve the conversion efficiency for the DSCs from 4.52 to 5.71%.

Synthesis and properties of iridium-doped hematite ({alpha}-Fe{sub 2}O{sub 3})

Energy Technology Data Exchange (ETDEWEB)

Krehula, Stjepko, E-mail: krehul@irb.hr [Division of Materials Chemistry, Ruder Boskovic Institute, P.O. Box 180, HR-10002 Zagreb (Croatia); Stefanic, Goran [Division of Materials Chemistry, Ruder Boskovic Institute, P.O. Box 180, HR-10002 Zagreb (Croatia); Zadro, Kreso [Department of Physics, Faculty of Science, University of Zagreb, Bijenicka 32, 10000 Zagreb (Croatia); Kratofil Krehula, Ljerka [Faculty of Chemical Engineering and Technology, University of Zagreb, Marulicev trg 19, 10000 Zagreb (Croatia); Marcius, Marijan; Music, Svetozar [Division of Materials Chemistry, Ruder Boskovic Institute, P.O. Box 180, HR-10002 Zagreb (Croatia)

2012-12-25

Highlights: Black-Right-Pointing-Pointer Ir-doped hematites were prepared by heating Ir-doped goethites. Black-Right-Pointing-Pointer Ir-doping in hematite led to an increase in unit cell and a decrease in crystallite size. Black-Right-Pointing-Pointer Ir-doping significantly affected magnetic, infrared and UV-Vis properties of hematite. Black-Right-Pointing-Pointer The Morin transition temperature increased with an increase in Ir-doping. Black-Right-Pointing-Pointer Ir ions brought about changes in the size and shape of the formed hematite particles. - Abstract: The effect of the incorporation of Ir{sup 3+} ions on the properties of {alpha}-Fe{sub 2}O{sub 3} formed by dehydroxylation of {alpha}-FeOOH was investigated using X-ray powder diffraction (XRD), thermogravimetric analysis (TGA), {sup 57}Fe Moessbauer, UV-Vis-NIR and FT-IR spectroscopies, SQUID magnetometer, field emission scanning electron microscopy (FE-SEM) and energy dispersive X-ray spectroscopy (EDS). Pure and Ir-doped hematite samples were obtained by heating of pure and Ir-doped goethites ({alpha}-FeOOH) formed by precipitation from mixed Fe(III)-Ir(III) chloride solutions in a highly alkaline medium. The incorporation of Ir{sup 3+} ions into the {alpha}-Fe{sub 2}O{sub 3} structure led to changes in unit-cell dimensions, crystallinity, particle size and shape, as well as changes in the magnetic, infrared and UV-Vis properties. An increase in the temperature of the Morin transition with an increase in Ir-doping was observed by Moessbauer spectroscopy and magnetic measurements.

The influence of interfacial barrier engineering on the resistance switching of In2O3:SnO2/TiO2/In2O3:SnO2 device

International Nuclear Information System (INIS)

Liu Zi-Yu; Zhang Pei-Jian; Meng Yang; Li Dong; Meng Qing-Yu; Li Jian-Qi; Zhao Hong-Wu

2012-01-01

The I—V characteristics of In 2 O 3 :SnO 2 /TiO 2 /In 2 O 3 :SnO 2 junctions with different interfacial barriers are investigated by comparing experiments. A two-step resistance switching process is found for samples with two interfacial barriers produced by specific thermal treatment on the interfaces. The nonsynchronous occurrence of conducting filament formation through the oxide bulk and the reduction in the interfacial barrier due to the migration of oxygen vacancies under the electric field is supposed to explain the two-step resistive switching process. The unique switching properties of the device, based on interfacial barrier engineering, could be exploited for novel applications in nonvolatile memory devices. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Solid solutions in the system Nd2(SeO4)3 - Sm2(SeO4)3 - H2O

International Nuclear Information System (INIS)

Serebrennikov, V.V.; Tsybukova, T.N.; Velikov, A.A.

1984-01-01

Using the method of isothermal solubility at 25 deg C the system Nd 2 (SeO 4 ) 3 -Sm 2 (SeO 4 ) 3 -H 2 O has been studied. Roentgenographic recording of solid ''residues'' is realized. For solid solutions energies of interchange and formation heats are calculated. Formation heats of solid solutions on the basis of samarium selenates are also found experimentally

Hydrothermal Synthesis of Pt-, Fe-, and Zn-doped SnO2 Nanospheres and Carbon Monoxide Sensing Properties

Directory of Open Access Journals (Sweden)

Weigen Chen

2013-01-01

Full Text Available Pure and M-doped (M = Pt, Fe, and Zn SnO2 nanospheres were successfully synthesized via a simple and facile hydrothermal method and characterized by X-ray powder diffraction, field-emission scanning electron microscopy, and energy dispersive spectroscopy. Chemical gas sensors were fabricated based on the as-synthesized nanostructures, and carbon monoxide sensing properties were systematically measured. Compared to pure, Fe-, and Zn-doped SnO2 nanospheres, the Pt-doped SnO2 nanospheres sensor exhibits higher sensitivity, lower operating temperature, more rapid response and recovery, better stability, and excellent selectivity. In addition, a theoretical study based on the first principles calculation was conducted. All results demonstrate the potential of Pt dopant for improving the gas sensing properties of SnO2-based sensors to carbon monoxide.

Moessbauer studies of SnO2 powders doped with dilute 57Fe, prepared by a sol-gel method

International Nuclear Information System (INIS)

Nomur, K.; Sakuma, J.; Takeda, M.

2006-01-01

Diluted magnetic semiconductor (DMS) is prospected as new materials with both semiconductor and magnetic properties. In order to confirm these phenomena, we prepared the powders of SnO 2 doped with various amount of 57 Fe by a sol-gel method. Various compositions of Sn 1-x 57 Fe x O 2 were obtained by mixing some ratio of Fe 3+ nitrate solution and acetylacetonate Sn 4+ complex in the ethylene glycol and citric acid solution. The solutions were evaporated, ashed at around 200 grad C, and finally annealed at 500 grad C, 600 grad C, and 650 grad C, respectively. These Sn 1-x 57 Fe x O 2 (x=0.005, 0.01, 0.03 and 0.05) were measured by XRD, VSM, and Moessbauer spectrometry. The prepared powder samples were confirmed to be a rutile structure, but iron compounds were not detected by XRD. Moessbauer spectra of Sn 1-x 57 Fe x O 2 prepared at 500 grad C were shown in Fig. 1. A small amount of broad sextets were observed in MS spectra of Sn 1-x 57 Fe x O 2 in addition to paramagnetic components. The relative intensity seems to be strong with the decrease of the amount of doped Fe. Moessbauer spectrum at 10 K shows clearly the magnetic components. The magnetic sextet was observed in MS spectra of samples prepared at 650 grad C, but the magnetic behavior weakened because of antiferromagnetic α-Fe 2 O 3 , produced due to the phase separation at high temperatures. (authors)

Espectroscopia Mössbauer e refinamento estrutural no sistema cerâmico isomórfico (alfa-Fe2O3-(alfa-Al2O 3 Mössbauer spectroscopy and structural refinement in the isomorphic (alpha-Fe2O3-( alpha-Al2O3 ceramic system

Directory of Open Access Journals (Sweden)

J. A. Moreto

2007-06-01

Full Text Available Os multiferróicos são materiais em que duas ou três propriedades tais como ferroeletricidade, ferromagnetismo e ferroelasticidade são observadas em uma mesma fase. Em particular, os multiferróicos magnetoelétricos representam os materiais que são simultaneamente (antiferromagnéticos e ferroelétricos, com ou sem ferroelasticidade. Especificamente, o sistema hematita (alfa-Fe2O3-alumina (alfa-Al2O3 tem sido estudado, principalmente devido às suas potencialidades para aplicações em metalurgia e como catalisador na síntese de amônia. Contudo, compostos deste sistema também podem apresentar efeitos magnetoelétricos. Neste trabalho um estudo estrutural do composto (alfa-Fe2O30,25(alfa-Al2O 30,75 submetido à moagem em altas energias e tratamento térmico pós-moagem é apresentado. As amostras foram caracterizadas por difração de raios X, refinamento estrutural Rietveld e espectroscopia Mössbauer. A determinação e identificação das fases cristalográficas, parâmetros de rede e volume de celas unitárias nas amostras moída e tratada termicamente permitiu verificar as mudanças dos parâmetros, a formação de espinélios e possíveis deformações relativas advindas do processo de moagem em altas energias.Multiferroics are materials in which two or all three of the properties, ferroelectricity, ferromagnetism, and ferroelasticity occur in the same phase. In particular, multiferroic magnetoelectrics represent the materials that are simultaneously ferromagnetic and ferroelectric, with or without ferroelasticity. Specifically, the hematite (alpha-Fe2O3-alumina (alpha-Al2O3 system has been studied, mainly due to its potential applications in metallurgy and as catalyst of ammonia synthesis. However, compounds of this system also may present magnetoelectric effects. In this work, a structural study of the high-energy ball milled and annealed (alpha-Fe2O3 0.25(alpha-Al2O30.75 compound was carefully conducted. The samples were

LPG sensing characteristics of electrospray deposited SnO2 nanoparticles

International Nuclear Information System (INIS)

Gürbüz, Mevlüt; Günkaya, Göktuğ; Doğan, Aydın

2014-01-01

Highlights: • SnO 2 nanopowder was deposited on conductive substrates using ESD technique. • Solution flow rate, coating time, substrate–nozzle distance and solid/alcohol ratio were studied to optimize SnO 2 film structure. • The gas sensing properties of tin oxide films were investigated using LPG. • The sensitivity of the films was increased with operating temperature. • The best sensitivity was observed for 20 LEL LPG at 450 °C operating temperature. - Abstract: In this study, SnO 2 films were fabricated on conductive substrate such as aluminum and platinum coated alumina using electro-spray deposition (ESD) method for gas sensor applications. Solution flow rate, coating time, substrate–nozzle distance and solid/alcohol ratio were studied to optimize SnO 2 film structure. The morphology of the deposited films was characterized by stereo and scanning electron microscopy (SEM). The gas sensing properties of tin oxide films were investigated using liquid petroleum gas (LPG) for various lower explosive limit (LEL). The results obtained from microscopic analyses show that optimum SnO 2 films were evaluated at flow rate of 0.05 ml/min, at distance of 6 cm, for 10 min deposition time, for 20 gSnO 2 /L ethanol ratio and at 7 kV DC electric field. By the results obtained from the gas sensing behavior, the sensitivity of the films was increased with operating temperature. The films showed better sensitivity for 20 LEL LPG concentration at 450 °C operating temperature

Screen printed In2O3-SnO2 nanocomposite: Structural and morphological properties and application for NO2 detection

Directory of Open Access Journals (Sweden)

Bessaïs B.

2012-06-01

Full Text Available In this work, we report on the sensing properties of screen-printed In2O3 (Indium Oxide while adding a moderate quantity of SnO2. It was found that the addition of SnO2 improves the response and decreases the operating temperature of the sensitive element for NO2 detection. However, a non-controlled amount of SnO2 leads to opposite result; for this reason in the present investigation we test films with different composition in order to optimize the quantity of SnO2 to be added. The crystallinity, roughness and morphology of the obtained In2O3-SnO2 anocomposite were analyzed using X-ray Diffraction (XRD, Transmission Electronic Microscopy (TEM and Atomic Force Microscopy (AFM. The atomic composition of the In2O3-SnO2 films was determined with the energy dispersive spectroscopy (EDX analysis during TEM observations. The effect of the composition on the cristallinity and morphological properties of the films was analyzed. Finally, the In2O3-SnO2 films were tested like sensitive elements for NO2 detection, wherein the effect of the composition was correlated with the sensor response in NO2 ambient. It was found that the addition of a moderate quantity of SnO2 to In2O3 exhibited high sensitivity at rather lower operating temperatures.

Accurate solid solution range of BiMnxFe3-xO6 and low temperature magnetism

Science.gov (United States)

Jiang, Pengfei; Yue, Mufei; Cong, Rihong; Gao, Wenliang; Yang, Tao

2017-11-01

BiMnxFe3-xO6 (x = 1) represents a new type of oxide structure containing Bi3+ and competing magnetic super-exchanges. In literature, multiple magnetic states were realized at low temperatures in BiMnFe2O6, and the hypothetical parent compounds (BiMn3O6, BiFe3O6) were predicted to be different in magnetism. Herein, we performed a careful study on the syntheses of BiMnxFe3-xO6 at ambient pressure, and the solid solution range was determined to be 0.9 ≤ x ≤ 1.3 by Rietveld refinements on high-quality powder X-ray diffraction data. Due to the very similar cationic size of Mn3+ and Fe3+, and possibly the structural rigidity, there was no significant structure change in the whole range of solid solution. The magnetic behavior of BiMnxFe3-xO6 (x = 1.2, 1.22, 1.26, 1.28 and 1.3) was generally similar to BiMnFe2O6, while the relative higher concentration of Mn3+ led to the decreasing of the antiferromagnetic ordering temperature.

The Research of Micro-structure and Gas Sensitivity of SnO2

Directory of Open Access Journals (Sweden)

Mingxin Song

2014-07-01

Full Text Available This paper adopts Sol-gel method and solid state reaction to make SnO2 matrix material and Sb2O3 is used as zuji to make SnO2 gas sensor under different sintering temperature. XRD analysis, SEM analysis and response time restoration test of working voltage sensitivity are choose to research SnO2 gas sensor constituents and influence factor on sensing properties by processing. Experiment results show that when the SnO2 make by sol-get method and Sb2O3 take up 2 %, Polyvinyl alcohol as an organic binder, platinum as catalyst, SnO2 gas sensor can get optimal integral sensing properties.

Li2SnO3 derived secondary Li-Sn alloy electrode for lithium-ion batteries

International Nuclear Information System (INIS)

Zhang, D.W.; Zhang, S.Q.; Jin, Y.; Yi, T.H.; Xie, S.; Chen, C.H.

2006-01-01

As a possible high-capacity Li-ion battery anode material, Li 2 SnO 3 was prepared via a solid-state reaction route and a sol-gel route, separately. Its electrochemical performance was tested in coin-type cells with metallic Li as the counter electrode. The results show that the sol-gel derived Li 2 SnO 3 has uniform nano-sized particles (200-300 nm) and can deliver a better reversible capacity (380 mAh/g after 50 cycles in the voltage window of 0-1 V) than that from the solid-state reaction route. The characterizations by means of galvanostatic cycling, cyclic voltammetry and ex situ X-ray diffraction indicate that the electrochemical process of the Li 2 SnO 3 lithiation proceeds with an initial structural reduction of the composite oxide into Sn-metal and Li 2 O followed by a reversible Li-Sn alloy formation in the Li 2 O matrix. Due to the buffer role of the Li 2 O matrix, the reversibility of the secondary Li-Sn alloy electrode is largely secured

Effect of {alpha}-Fe{sub 2}O{sub 3} addition on the morphological, optical and decolorization properties of ZnO nanostructures

Energy Technology Data Exchange (ETDEWEB)

Abdullah Mirzaie, Rasol, E-mail: mirzai_r@yahoo.com [Dep. of Chemistry, Faculty of Science, Shahid Rajaee Teacher Training University, P.O. Box 167855-163, Tehran (Iran, Islamic Republic of); Kamrani, Firouzeh [Masters Student in Physical Chemistry, Faculty of Science, Shahid Rajaee Teacher Training University, P.O. Box 167855-163, Tehran (Iran, Islamic Republic of); Anaraki Firooz, Azam [Dep. of Chemistry, Faculty of Science, Shahid Rajaee Teacher Training University, P.O. Box 167855-163, Tehran (Iran, Islamic Republic of); Khodadadi, Abbas Ali [Oil and Gas Processing Center of Excellence, School of Chemical Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of)

2012-03-15

Highlights: Black-Right-Pointing-Pointer Different morphologies of Fe{sub 2}O{sub 3}/ZnO nanocomposites synthesized via simple solid state reaction method. Black-Right-Pointing-Pointer Various Fe{sup 3+}/Zn{sup 2+} ratios affected on morphology, size and optical absorption. Black-Right-Pointing-Pointer addition of Fe{sub 2}O{sub 3} shifted the absorption edge to the visible region. Black-Right-Pointing-Pointer Amount of added Fe{sub 2}O{sub 3} strongly affected the decolorization of azo dye under visible light. - Abstract: Visible light sensitive photocatalysts of Fe{sub 2}O{sub 3}/ZnO nanocomposites were prepared by a simple solid-state reaction method, using zinc acetate, {alpha}-Fe{sub 2}O{sub 3} and sodium hydroxide at room temperature. The products were characterized by scanning electron microscopy, powder X-ray diffraction, N{sub 2} adsorption-desorption measurement, UV-vis absorption, and photoluminescence spectroscopy and used for photodecolorization of Congo red. The characterization results showed that the morphology, crystallite size, BET surface area and optical absorption of the samples varied significantly with the Fe{sup 3+} to Zn{sup 2+} ratios. The nanocomposites show two absorption edges at ultraviolet and visible region. The optical band gap values of these nanocomposites were calculated to be about 3.98-3.81 eV and 2.88-2.98 eV, which show a red shift from that of pure ZnO. These red shifts are related to the formation of Fe s-levels below the conductive band edge of ZnO and effectively extend the absorption edge into the visible region. The growth mechanisms of the samples are proposed. These nanocomposites showed high decolorization ability in visible light with wavelength up to about 400 nm. Among the samples, Fe{sub 2}O{sub 3}/ZnO nanoflower (molar ratio of Fe{sup 3+} to Zn{sup 2+} is 1:100) exhibited higher decolorization efficiency than the other nanocomposites. It could be considered as a promising photocatalyst for dyes treatment.

A comparative study of dissolution of {alpha}-Fe{sub 2}O{sub 3} and {gamma}-Fe{sub 2}O{sub 3} in DCD formulations

Energy Technology Data Exchange (ETDEWEB)

Ranganathan, S.; Raghavan, P.S.; Gopalan, R. [Madras Christian Coll. (India). Dept. of Chemistry; Srinivasan, M.P.; Narasimhan, S.V.

1998-12-31

The important corrosion products deposited on the surfaces of structural materials such as stainless steel in the primary coolant system of BWRs are haematite in the outer layers and ferrites such as magnetite, nickel ferrite, cobalt ferrite, etc., in the inner layers. Magnetite dissolution by 2, 6 Pyridinedicarboxylic acid (PDCA), Ethylenediaminetetraacetic acid (EDTA) and Nitrolotriacetic acid (NTA) showed that there is an optimum pH of dissolution for each ligand. The leaching of the metal ions from the oxides is controlled in part by reductive dissolution; this is due to the presence of Fe(II)-L complexes generated from the released Fe{sup 2+} ions. The addition of Fe(II)-L with the formulation greatly increases the rate of dissolution. In order to understand the role of Fe{sup 2+} arising from the spinel lattice of Fe{sub 3}O{sub 4} in aiding the dissolution of magnetite, it is appropriate to study the dissolution behaviour of the system like Fe{sub 2}O{sub 3} which is not containing any Fe{sup 2+} in the crystal lattice. The present study has been carried out with {alpha}-Fe{sub 2}O{sub 3} and {gamma}-Fe{sub 2}O{sub 3} in DCD formulation in the presence of ascorbic acid and with the addition of Fe(II)-L as a reductant. (author)

Preparation, structural, dielectric and magnetic properties of LaFeO3–PbTiO3 solid solutions

International Nuclear Information System (INIS)

Ivanov, S.A.; Tellgren, R.; Porcher, F.; Ericsson, T.; Mosunov, A.; Beran, P.; Korchagina, S.K.; Kumar, P. Anil; Mathieu, R.; Nordblad, P.

2012-01-01

Highlights: ► Solid-solutions of (1−x)LaFeO 3 –(x)PbTiO 3 were synthesized by solid-state reaction. ► XRPD and NPD evidence orthorhombic (x 0.8) crystal structures. ► LaFeO 3 -rich compositions order antiferromagnetically (x 3 -rich compositions exhibit ferroelectric order (x larger than 0.8). ► Magnetic and dielectric (relaxor) ordering coexist near room-temperature around x = 0.4. -- Abstract: Solid solutions of (1−x)LaFeO 3 –(x)PbTiO 3 (0 3+ cations in the B-site with propagation vector k = (0,0,0). Based on the obtained experimental data, a combined structural and magnetic phase diagram has been constructed. The factors governing the structural, dielectric and magnetic properties of (1−x)LaFeO 3 –(x)PbTiO 3 solid solutions are discussed, as well as their possible multiferroicity.

Synthesis and characterization of Sr2Ir1−xMxO4 (M=Ti, Fe, Co) solid solutions

International Nuclear Information System (INIS)

Gatimu, Alvin J.; Berthelot, Romain; Muir, Sean; Sleight, Arthur W.; Subramanian, M.A.

2012-01-01

The effects of Ti, Fe and Co substitutions for Ir on the structure and on the physical properties of Sr 2 IrO 4 are investigated. A complete solid solution Sr 2 Ir 1−x Ti x O 4 is obtained while both Fe and Co doping are relatively limited. In each case however, the c-axis cell parameter and the initial IrO 6 octahedra tilting decreases with substitution. Doping with Ti, Fe and Co results in a decrease of the magnetic susceptibility and in an increase in the paramagnetic effective moment for Co and Fe doped samples and a suppression of the weak ferromagnetic ordering observed for Sr 2 IrO 4 . - Graphical abstract: Solid solutions of Sr 2 Ir 1−x M x O 4 (M=Ti, Fe, Co) have been synthesized and characterized by powder X-ray diffraction, magnetism and electrical measurements. Changes in the a parameter and decreases in both the c-axis cell parameters and the initial IrO 6 octahedra tilting are found to be correlated. Highlights: ► Solid Solutions of Sr 2 Ir 1−x M x O 4 (M=Ti, Fe, Co) are synthesized. ► The Sr 2 Ir 1−x Ti x O 4 solid solution is complete while those of Fe and Co are relatively limited. ► The change in a cell parameter with substitution is much less than that of the c parameter. ► Decreased tilting and the smaller size of the M cation contrastingly affect the a parameter. ► Doping results in a suppression of the weak ferromagnetic ordering in Sr 2 IrO 4 .

Self-assembled 3-D flower-shaped SnO2 nanostructures with improved electrochemical performance for lithium storage

International Nuclear Information System (INIS)

Yang Rong; Gu Yingan; Li Yaoqi; Zheng Jie; Li Xingguo

2010-01-01

Flower-shaped SnO 2 nanoplates were successfully synthesized via a simple hydrothermal treatment of a mixture of tin(II) dichloride dihydrate (SnCl 2 .2H 2 O) and sodium citrate (Na 3 C 6 H 5 O 7 .2H 2 O) in alkali solution. The obtained SnO 2 nanoplates were less than 5 nm thick and self-assembled into flower-shaped nanostructures. The introduction of citrate was essential for the preparation of the SnO 2 nanoplates. The nanoscale shape and self-assembled architecture of SnO 2 nanoparticles were mainly controlled by the alkalinity of the solution. When the self-assembled SnO 2 nanostructures were used as anode materials in Li-ion batteries, they exhibit a reversible capacity of 670 mA h g -1 after 30 cycles and an average capacity fading of 0.95% per cycle after the second cycle. The good electrochemical performance of the SnO 2 sample prepared via the hydrothermal synthesis indicates the possibility of fabricating specific self-assembled three-dimensional nanostructures for Li-ion batteries.

Densificação rápida de cerâmicas de SnO2 Fast densification of SnO2 ceramics

Directory of Open Access Journals (Sweden)

G. J. Pereira

2003-04-01

Full Text Available Os pós à base de óxido de estanho são conhecidos por apresentarem baixa densificação mesmo a temperaturas de sinterização acima de 1500 °C. A introdução de diferentes íons metálicos como Mn2+, Fe3+ e Cu2+ induzem a redução do volume de poros e crescimento de grãos durante a sinterização. Pós à base de SnO2 foram preparados pela rota química derivada da patente de Pechini, contendo diferentes concentrações de Mg2+ ou Fe3+. Todas as amostras apresentaram uma alta taxa de densificação nos momentos iniciais, quando sinterizadas por "fast firing". As amostras contendo 5% em mol de ferro sinterizadas durante 30 s a 1200 °C apresentaram densidades superiores às amostras sinterizadas por aquecimento em taxas normais (10 °C/min por 4 h a 1200 °C. O fenômeno de eliminação rápida de poros pode ser explicado, levando em conta o papel da superfície no fenômeno de sinterização. A saturação da superfície pelo aditivo foi confirmada por medidas de mobilidade eletroforética dinâmica com base na literatura e em dados experimentais.Tin oxide based powders without additives present low densification even at high sintering temperatures. Different metal cations such as Fe3+, Mn2+ and Cu2+ are introduced into such powders and induce pore volume reduction during sintering. In this work, SnO2 based powders were prepared with different amounts of Mg2+ and Fe3+ by a polymeric chemical process derived from Pechini's method. All samples presented high initial densification rate when sintered by fast firing. SnO2 samples containing 5 mol % of iron ions and sintered by fast firing at 1200 °C during 30 s were denser than samples with the same composition but sintered by conventional method, e.g., 1200 °C during 4 h at 10 °C/min. The fast densification could be understood considering the role of the surface on the sintering phenomenon. The surface saturation was verified by electrokinetic mobility measurements and reported results.

Effect of phase interaction on catalytic CO oxidation over the SnO_2/Al_2O_3 model catalyst

International Nuclear Information System (INIS)

Chai, Shujing; Bai, Xueqin; Li, Jing; Liu, Cheng; Ding, Tong; Tian, Ye; Liu, Chang; Xian, Hui; Mi, Wenbo; Li, Xingang

2017-01-01

Highlights: • Activity for CO oxidation is greatly enhanced by interaction between SnO_2 and Al_2O_3. • Interaction between SnO_2 and Al_2O_3 phases can generate oxygen vacancies. • Oxygen vacancies play an import role for catalytic CO oxidation. • Sn"4"+ cations are the effective sites for catalytic CO oxidation. • Langmuir-Hinshelwood model is preferred for catalytic CO oxidation. - Abstract: We investigated the catalytic CO oxidation over the SnO_2/Al_2O_3 model catalysts. Our results show that interaction between the Al_2O_3 and SnO_2 phases results in the significantly improved catalytic activity because of the formation of the oxygen vacancies. The oxygen storage capacity of the SnO_2/Al_2O_3 catalyst prepared by the physically mixed method is nearly two times higher than that of the SnO_2, which probably results from the change of electron concentration on the interface of the SnO_2 and Al_2O_3 phases. Introducing water vapor to the feeding gas would a little decrease the activity of the catalysts, but the reaction rate could completely recover after removal of water vapor. The kinetics results suggest that the surface Sn"4"+ cations are effective CO adsorptive sites, and the surface adsorbed oxygen plays an important role upon CO oxidation. The reaction pathways upon the SnO_2-based catalysts for CO oxidation follow the Langmuir-Hinshelwood model.

Efficient photocatalytic degradation of phenol in aqueous solution by SnO2:Sb nanoparticles

International Nuclear Information System (INIS)

Al-Hamdi, Abdullah M.; Sillanpää, Mika; Bora, Tanujjal; Dutta, Joydeep

2016-01-01

Highlights: • Sb doped SnO 2 nanoparticles were synthesized using sol–gel process. • Photocatalytic degradation of phenol were studies using SnO 2 :Sb nanoparticles. • Under solar light phenol was degraded within 2 h. • Phenol mineralization and intermediates were investigated by using HPLC. - Abstract: Photodegradation of phenol in the presence of tin dioxide (SnO 2 ) nanoparticles under UV light irradiation is known to be an effective photocatalytic process. However, phenol degradation under solar light is less effective due to the large band gap of SnO 2 . In this study antimony (Sb) doped tin dioxide (SnO 2 ) nanoparticles were prepared at a low temperature (80 °C) by a sol–gel method and studied for its photocatalytic activity with phenol as a test contaminant. The catalytic degradation of phenol in aqueous media was studied using high performance liquid chromatography and total organic carbon measurements. The change in the concentration of phenol affects the pH of the solution due to the by-products formed during the photo-oxidation of phenol. The photoactivity of SnO 2 :Sb was found to be a maximum for 0.6 wt.% Sb doped SnO 2 nanoparticles with 10 mg L −1 phenol in water. Within 2 h of photodegradation, more than 95% of phenol could be removed under solar light irradiation.

Porous SnO2-CuO nanotubes for highly reversible lithium storage

Science.gov (United States)

Cheong, Jun Young; Kim, Chanhoon; Jung, Ji-Won; Yoon, Ki Ro; Kim, Il-Doo

2018-01-01

Facile synthesis of rationally designed structures is critical to realize a high performance electrode for lithium-ion batteries (LIBs). Among different candidates, tin(IV) oxide (SnO2) is one of the most actively researched electrode materials due to its high theoretical capacity (1493 mAh g-1), abundance, inexpensive costs, and environmental friendliness. However, severe capacity decay from the volume expansion and low conductivity of SnO2 have hampered its use as a feasible electrode for LIBs. Rationally designed SnO2-based nanostructures with conductive materials can be an ideal solution to resolve such limitations. In this work, we have successfully fabricated porous SnO2-CuO composite nanotubes (SnO2-CuO p-NTs) by electrospinning and subsequent calcination step. The porous nanotubular structure is expected to mitigate the volume expansion of SnO2, while the as-formed Cu from CuO upon lithiation allows faster electron transport by improving the low conductivity of SnO2. With a synergistic effect of both Sn and Cu-based oxides, SnO2-CuO p-NTs deliver stable cycling performance (91.3% of capacity retention, ∼538 mAh g-1) even after 350 cycles at a current density of 500 mA g-1, along with enhanced rate capabilities compared with SnO2.

Long afterglow property of Er"3"+ doped Ca_2SnO_4 phosphor

International Nuclear Information System (INIS)

Zhang, Dongyun; Shi, Mingming; Sun, Yiwen; Guo, Yunyun; Chang, Chengkang

2016-01-01

A novel green emitting long afterglow phosphor, Er"3"+ -doped Ca_2SnO_4 (Ca_2SnO_4:Er"3"+), was prepared successfully via a traditional high temperature solid–state reaction method. Its properties have been characterized and analyzed by utilizing x-ray diffraction (XRD), photoluminescence spectroscope (PLS), afterglow decay curve (ADC) and thermal luminescence spectroscope (TLS). Three main emission peaks of PLS locate at 524, 550 and 668 nm, corresponding to CIE chromaticity coordinates of x = 0.326, y = 0.6592. An optimal doping concentration of Er"3"+ of 2% was determined. The Ca_2SnO_4:Er"3"+ phosphors showed a typical triple-exponential afterglow decay behavior when the UV source was switched off. Thermal simulated luminescence study indicated that the persistent afterglow of Ca_2SnO_4:2 mol% Er"3"+ phosphors was generated by the suitable electron or hole traps which were resulted from the doping the Ca_2SnO_4 host with rare-earth ions (Er"3"+). - Highlights: • A novel green emitting long afterglow phosphor, Ca_2SnO_4:Er"3"+, was prepared. • An optimal doping concentration of Er"3"+ of 2% was determined. • After the UV source was turned off, the Ca_2SnO_4:Er"3"+ showed a typical triple-exponential afterglow decay behavior. • CIE chromaticity coordinates results confirmed a green light emitting of the Ca_2SnO_4:Er"3"+. • The persistent afterglow of the Ca_2SnO_4:Er"3"+ was attributed to suitable electron or hole traps.

Effects of NO{sub x}, {alpha}-Fe{sub 2}O{sub 3}, {gamma}-Fe{sub 2}O{sub 3}, and HCl on mercury transformations in a 7-kW coal combustion system

Energy Technology Data Exchange (ETDEWEB)

Galbreath, Kevin C.; Zygarlicke, Christopher J.; Tibbetts, James E.; Schulz, Richard L.; Dunham, Grant E. [University of North Dakota Energy and Environmental Research Center, 15 North 23rd Street, P.O. Box 9018, Grand Forks, ND 58202-9018 (United States)

2005-01-25

Bench-scale investigations indicate that NO, NO{sub 2}, hematite ({alpha}-Fe{sub 2}O{sub 3}), maghemite ({gamma}-Fe{sub 2}O{sub 3}), and HCl promote the conversion of gaseous elemental mercury (Hg{sup 0}) to gaseous oxidized mercury (Hg{sup 2+}) and/or particle-associated mercury (Hg[p]) in simulated coal combustion flue gases. In this investigation, the effects of NO{sub x}, {alpha}-Fe{sub 2}O{sub 3}, {gamma}-Fe{sub 2}O{sub 3}, and HCl on Hg transformations were evaluated by injecting them into actual coal combustion flue gases produced from burning subbituminous Absaloka and lignitic Falkirk coals in a 7-kW down-fired cylindrical furnace. A bituminous Blacksville coal known to produce an Hg{sup 2+}-rich combustion flue gas was also burned in the system. The American Society for Testing and Materials Method D6784-02 (Ontario Hydro method) or an online Hg analyzer equipped to measure Hg{sup 0} and total gaseous mercury (Hg[tot]) was used to monitor Hg speciation at the baghouse inlet (160-195 {sup o}C) and outlet (110-140 {sup o}C) locations of the system. As expected, the baseline Blacksville flue gas was composed predominantly of Hg{sup 2+} (Hg{sup 2+}/Hg[tot]=0.77), whereas Absaloka and Falkirk flue gases contained primarily Hg{sup 0} (Hg{sup 0}/Hg[tot]=0.84 and 0.78, respectively). Injections of NO{sub 2} (80-190 ppmv) at 440-880 {sup o}C and {alpha}-Fe{sub 2}O{sub 3} (15 and 6 wt.%) at 450 {sup o}C into Absaloka and Falkirk coal combustion flue gases did not significantly affect Hg speciation. The lack of Hg{sup 0} to Hg{sup 2+} conversion suggests that components of Absaloka and Falkirk combustion flue gases and/or fly ashes inhibit heterogeneous Hg{sup 0}-NO{sub x}-{alpha}-Fe{sub 2}O{sub 3} reactions or that the flue gas quench rate in the 7-kW system is much different in relation to bench-scale flue gas simulators.An abundance of Hg{sup 2+}, HCl, and {gamma}-Fe{sub 2}O{sub 3} in Blacksville flue gas and the inertness of injected {alpha}-Fe{sub 2}O{sub 3

Tree-like SnO2 nanowires and optical properties

International Nuclear Information System (INIS)

Tao Tao; Chen Qiyuan; Hu Huiping; Chen Ying

2011-01-01

Research highlights: → Tree-like SnO 2 nanowires can be grown as low as 1100 deg. C by a vapour-solid process using a milled SnO 2 powder as the evaporation source. → FT-IR and PL measurements have shown that the tree-like nanostructures lead to superb physical properties. → The PL spectrum of such tree-like nanowires exhibits a strong PL peak at 548 nm. - Abstract: Tree-like SnO 2 nanowires have been grown by a vapor-solid process using a milled SnO 2 powder as the evaporation source. Phase, structural evolution and chemical composition were investigated using X-ray diffraction (XRD), X-ray spectrometry (EDS), and scanning electron microscopy (SEM). The process yields a large proportion of ultra-long rutile nanowires of 50-150 nm diameter and lengths up to several tens of micrometers. High-resolution transmission electron microscopy (HRTEM) shows that the SnO 2 nanowires are single crystals in the (1 0 1) growth direction with scattered smaller crystals or nanowires as the tree branches. The SnO 2 nanostructures were also examined using Fourier transform infra-red (FT-IR) and photoluminescence (PL) spectroscopy. A strong emission band centered at 548 nm dominated the PL spectrum of the tree-like nanowires.

Residual tensile stresses and piezoelectric properties in BiFeO3-Bi(Zn1/2Ti1/2O3-PbTiO3 ternary solid solution perovskite ceramics

Directory of Open Access Journals (Sweden)

Weilin Zheng

2016-08-01

Full Text Available For low dielectric loss perovskite-structured (1-x-yBiFeO3-xBi(Zn1/2Ti1/2O3-yPbTiO3 (BF-BZT-PT (x = 0.04-0.15 and y = 0.15-0.26 ceramics in rhombohedral/tetragonal coexistent phase, structural phase transitions were studied using differential thermal analyzer combined with temperature-dependent dielectric measurement. Two lattice structural phase transitions are disclosed in various BF-BZT-PT perovskites, which is different from its membership of BiFeO3 exhibiting just one lattice structural phase transition at Curie temperature TC= 830oC. Consequently, residual internal tensile stresses were revealed experimentally through XRD measurements on ceramic pellets and counterpart powders, which are reasonably attributed to special structural phase transition sequence of BF-BZT-PT solid solution perovskites. Low piezoresponse was observed and argued extrinsically resulting from residual tensile stresses pinning ferroelectric polarization switching. Post-annealing and subsequent quenching was found effective for eliminating residual internal stresses in those BZT-less ceramics, and good piezoelectric property of d33 ≥ 28 pC/N obtained for 0.70BF-0.08BZT-0.22PT and 0.05 wt% MnO2-doped 0.70BF-0.04BZT-0.26PT ceramics with TC ≥ 640oC, while it seemed no effective for those BZT-rich BF-BZT-PT ceramics with x = 0.14 and 0.15 studied here.

Photocatalytic performance of nano-photocatalyst from TiO{sub 2} and Fe{sub 2}O{sub 3} by mechanochemical synthesis

Energy Technology Data Exchange (ETDEWEB)

Ghorai, Tanmay K., E-mail: tanmay_ghorai@yahoo.co.in [Department of Chemistry, West Bengal State University, Barasat, North 24 Pgs, Kolkata 700126 (India); Department of Chemistry, Indian Institute of Technology Kharagpur, Kharagpur 721302 (India); Chakraborty, Mukut [Department of Chemistry, West Bengal State University, Barasat, North 24 Pgs, Kolkata 700126 (India); Pramanik, Panchanan [Department of Chemistry, Indian Institute of Technology Kharagpur, Kharagpur 721302 (India)

2011-08-11

Graphical abstract: Nano-particles of homogeneous solution between TiO{sub 2} and Fe{sub 2}O{sub 3} (up to 5 mol%) have been prepared by mechanochemical milling. The results show that the alloy of TiO{sub 2} with 5 mol% of Fe{sub 2}O{sub 3} (YFT1) exhibit photocatalytic activity 3-5 times higher than that of P25 TiO{sub 2} for oxidation of various dyes (RB, MO, TB and BG) under visible light irradiation. The average particle size and crystallite size of YFT1 were found to be 30 {+-} 5 nm and 12 nm measured from TEM and XRD. Optical adsorption edge is found to be 2.26 eV. Tentative schematic diagram of reaction mechanism of YFT/RFT photocatalysts under visible light irradiation. Highlights: > Synthesis of nano-sized homogeneous solid solution between Fe{sub 2}O{sub 3} and TiO{sub 2} with high photocatalytic activity for oxidative degradation of different dyes was successfully obtained through mechanochemical synthesis. XRD data shows the formation of solid solution having anatase structure with no free Fe{sub 2}O{sub 3} up to 5 mol% of Fe{sub 2}O{sub 3}. Fe{sub 2}O{sub 3}/TiO{sub 2} catalyst have crystallite size about 12-13 nm measured from XRD and particle size about 30 {+-} 5 nm measured from TEM. FT-IR of all Fe{sub 2}O{sub 3}/TiO{sub 2} prepared catalysts is similar to pure TiO{sub 2}. The maximum solubility of Fe{sub 2}O{sub 3} in TiO{sub 2} is 5 mol% of Fe{sub 2}O{sub 3} irrespective of source and this composition has highest photocatalytic activity that is 3-5 times higher than P25 TiO{sub 2} for the oxidation of different dyes. We also observed that the rate of degradation of Rhodamine B is faster among all the four dyes under prepared catalyst and visible light. - Abstract: Nano-particles of homogeneous solid solution between TiO{sub 2} and Fe{sub 2}O{sub 3} (up to 10 mol%) have been prepared by mechanochemical milling of TiO{sub 2} and yellow Fe{sub 2}O{sub 3}/red Fe{sub 2}O{sub 3}/precipitated Fe (OH){sub 3} using a planetary ball mill. Such novel solid

Liquid-Solid-Solution Assembly of CoFe2O4/Graphene Nanocomposite as a High-Performance Lithium-Ion Battery Anode

International Nuclear Information System (INIS)

Zhu, Yanfang; Lv, Xingbin; Zhang, Lili; Guo, Xiaodong; Liu, Daijun; Chen, Jianjun; Ji, Junyi

2016-01-01

Graphical abstract: CoFe 2 O 4 /rGO composites are fabricated via a liquid-solid-solution assemble strategy with a well controlled CoFe 2 O 4 size, the composite exhibits a high rate performance for lithium ion batteries anode. - Highlights: • Crumpled CoFe 2 O 4 @graphene composite with uniform CoFe 2 O 4 nanoparticles intimately anchored on graphene sheets was fabricated. • The novel fabrication strategy: liquid-solid-solution strategy where the CoFe 2 O 4 are nucleation and controlled growth at the oil/water interface. • High reversible specific capacity of 1102 mAh g −1 after 100 cycles and high rate capability of 410 mAh g −1 within 230 s charging. - Abstract: CoFe 2 O 4 /graphene composites were fabricated via a novel one-pot liquid-solid-solution (LSS) hydrothermal process. Through ions electrostatic adsorption onto graphene sheets and oil microemulsion encapsulation, CoFe 2 O 4 nanoparticles can be uniformly anchored on crumpled graphene sheets without aggregation, and the size distribution of CoFe 2 O 4 particles can be controlled by the microemulsion shell in the range of 50–100 nm. With the synergistic effect between CoFe 2 O 4 and graphene, the CoFe 2 O 4 /graphene hybrid exhibits a high reversible specific capacity of 1102 mAh g −1 at 0.2 A g −1 after 100 cycles, and a good cycling stability as well. Moreover, the composite has good rate capability. The specific capacity can reach a high value of 410 mAh g −1 even under a high current density of 6.4 A g −1 (corresponds to a charge time of ∼230 s), indicating its promising application as an anode material for lithium ion batteries.

Epitaxial growth of branched {alpha}-Fe{sub 2}O{sub 3}/SnO{sub 2} nano-heterostructures with improved lithium-ion battery performance

Energy Technology Data Exchange (ETDEWEB)

Zhou, Weiwei; Cheng, Chuanwei; Jia, Xingtao; Yu, Ting; Fan, Hong Jin [Division of Physics and Applied Physics, School of Physical and Mathematical Sciences, Nanyang Technological University, 637371 (Singapore); Liu, Jinping; Jiang, Jian [Institute of Nanoscience and Nanotechnology, Department of Physics, Huazhong Normal University, Wuhan 430079 (China); Tay, Yee Yan; Hng, Huey Hoon [School of Materials Science and Engineering, Nanyang Technological University, 639798 (Singapore); Zhang, Jixuan; Gong, Hao [Department of Materials Science and Engineering, National University of Singapore, 117576 (Singapore)

2011-07-08

We report the synthesis of a novel branched nano-heterostructure composed of SnO{sub 2} nanowire stem and {alpha}-Fe{sub 2}O{sub 3} nanorod branches by combining a vapour transport deposition and a facile hydrothermal method. The epitaxial relationship between the branch and stem is investigated by high resolution transmission electron microscopy (HRTEM). The SnO{sub 2} nanowire is determined to grow along the [101] direction, enclosed by four side surfaces. The results indicate that distinct crystallographic planes of SnO{sub 2} stem can induce different preferential growth directions of secondary nanorod branches, leading to six-fold symmetry rather than four-fold symmetry. Moreover, as a proof-of-concept demonstration of the function, such {alpha}-Fe{sub 2}O{sub 3}/SnO{sub 2} composite material is used as a lithium-ion batteries (LIBs) anode material. Low initial irreversible loss and high reversible capacity are demonstrated, in comparison to both single components. The synergetic effect exerted by SnO{sub 2} and {alpha}-Fe{sub 2}O{sub 3} as well as the unique branched structure are probably responsible for the enhanced performance. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Enhancing Performance of SnO2-Based Dye-Sensitized Solar Cells Using ZnO Passivation Layer

Directory of Open Access Journals (Sweden)

W. M. N. M. B. Wanninayake

2016-01-01

Full Text Available Although liquid electrolyte based dye-sensitized solar cells (DSCs have shown higher photovoltaic performance in their class, they still suffer from some practical limitations such as solvent evaporation, leakage, and sealing imperfections. These problems can be circumvented to a certain extent by replacing the liquid electrolytes with quasi-solid-state electrolytes. Even though SnO2 shows high election mobility when compared to the semiconductor material commonly used in DSCs, the cell performance of SnO2-based DSCs is considerably low due to high electron recombination. This recombination effect can be reduced through the use of ultrathin coating layer of ZnO on SnO2 nanoparticles surface. ZnO-based DSCs also showed lower performance due to its amphoteric nature which help dissolve in slightly acidic dye solution. In this study, the effect of the composite SnO2/ZnO system was investigated. SnO2/ZnO composite DSCs showed 100% and 38% increase of efficiency compared to the pure SnO2-based and ZnO-based devices, respectively, with the gel electrolyte consisting of LiI salt.

Characteristics of RuO2-SnO2 nanocrystalline-embedded amorphous electrode for thin film microsupercapacitors

International Nuclear Information System (INIS)

Kim, Han-Ki; Choi, Sun-Hee; Yoon, Young Soo; Chang, Sung-Yong; Ok, Young-Woo; Seong, Tae-Yeon

2005-01-01

The characteristics of RuO 2 -SnO 2 nanocrystalline-embedded amorphous electrode, grown by DC reactive sputtering, was investigated. X-ray diffraction (XRD), transmission electron microscopy (TEM), and transmission electron diffraction (TED) examination results showed that Sn and Ru metal cosputtered electrode in O 2 /Ar ambient have RuO 2 -SnO 2 nanocrystallines in an amorphous oxide matrix. It is shown that the cyclic voltammorgram (CV) result of the RuO 2 -SnO 2 nanocrystalline-embedded amorphous film in 0.5 M H 2 SO 4 liquid electrolyte is similar to a bulk-type supercapacitor behavior with a specific capacitance of 62.2 mF/cm 2 μm. This suggests that the RuO 2 -SnO 2 nanocrystalline-embedded amorphous film can be employed in hybrid all-solid state energy storage devises as an electrode of supercapacitor

Effect of doping and chemical ordering on the optoelectronic properties of complex oxides: Fe ₂ O ₃ –V ₂ O ₃ solid solutions and hetero-structures

Energy Technology Data Exchange (ETDEWEB)

Nayyar, Iffat H.; Chamberlin, Sara E.; Kaspar, Tiffany C.; Govind, Niranjan; Chambers, Scott A.; Sushko, Petr

2017-01-01

The electronic and optical properties of a-(Fe1xVx)2O3 at low (x = 0.04) and high (x = 0.5) doping levels are investigated using a combination of periodic and embedded cluster approaches, and time dependent density functional theory. At low V concentrations the onset of the optical absorption is B0.5 eV (i.e., nearly 1.6 eV lower than that in pure a-Fe2O3) and corresponds to the electron transitions from V 3d to Fe 3d* orbitals. At high V concentrations, optical absorption energies and intensities are sensitive to specific arrangements of Fe and V atoms and their spin configuration that determine Fe–V hybridization. The onset of the lowest inter-vanadium absorption band in the case of Fe2O3/V2O3 hetero-structures is as low as B0.3 eV and the corresponding peak is at B0.7 eV. In contrast, in the case of solid solutions this peak has lower intensity and is shifted to higher energy (B1.2 eV). Analysis of the orbital character of electronic excitation suggests that Fe2O3/V2O3 hetero-structures absorb light much more effectively than random alloys, thus promoting efficient photo-induced carrier generation. These predictions can be tested in a-(Fe1xVx)2O3 thin films synthesized with well-controlled spatial distribution of Fe and V species.

Preparation of SnO2 Nanoparticles by Two Different Wet Chemistry Methods

International Nuclear Information System (INIS)

Ridha, N.J.; Akrajas Ali Umar; Muhammad Yahya; Muhammad Mat Salleh; Mohamad Hafizuddin Jumali

2011-01-01

The objective of this project is to prepare SnO 2 nanoparticles by two different wet chemistry methods namely sol gel and direct growth methods. The XRD results indicated that both samples are single phase SnO 2 . The FE-SEM micrographs displayed that SnO 2 nanoparticles prepared in first method exhibited a round shape with particle size around 15 nm while the second method produced SnO 2 nano rod with length and width of 570 nm and 55 nm respectively. Energy gap values for SnO 2 nanospheres and nano rods were 4.38 and 4.34 eV respectively. (author)

Preparation and electrochemical characterization of size controlled SnO2-RuO2 composite powder for monolithic hybrid battery

International Nuclear Information System (INIS)

Jeon, Young-Ah; No, Kwang-Soo; Choi, Sun Hee; Ahn, Jae pyong; Yoon, Young Soo

2004-01-01

Tin oxide (SnO 2 ) powders with a particle size of ∼20 nm were synthesized by a gas condensation method. Ruthenium oxide was loaded by an incipient-wetness method, in which an aqueous solution of RuCl 3 was added to the manufactured SnO 2 powder in an amount that was just sufficient to wet completely the powder. And then, the resulting solution was obtained after freeze-drying to synthesis the smallest particle. The as-synthesized SnO 2 powder with 1.5 wt.% ruthenium oxide (RuO 2 ) exhibited well-developed facets and had a very uniform particle size. The first discharge capacity was lower than comparing to commercial powder because of forming the second phase, but showed good cyclability. A maximum specific electrode capacitance of ∼20 F/g and a maximum specific power of ∼80 W/kg were achieved by manufactured SnO 2 with 1.5 wt.% RuO 2 . This result indicated that the synthesized SnO 2 -RuO 2 composite powder of nano-size scale is candidate for use in fabricating monolithic hybrid batteries using suitable electrolyte as well

Study on adsorption of 99Tc on Fe, Fe2O3 and Fe3O4

International Nuclear Information System (INIS)

Liu Dejun; Fan Xianhua; Zhang Yingjie; Yao Jun; Zhou Duo; Wang Yong

2004-01-01

The absorption behavior of 99 Tc on Fe, Fe 2 O 3 and Fe 3 O 4 powders from aqueous 99 TcO 4 - solutions is studied by batch method in atmospheric conditions. After the adsorption reaches equilibrium, the valence state of 99 Tc in the aqueous solution is examined by extraction with tetraphenylarsonium chloride. The experimental results show that the adsorption ratio of 99 Tc on iron powders decreases with the increase of pH (in the range of 5-8) and of CO 3 2- concentration (in the range of 1 x 10 -8 -1 x 10 -2 mol/L). In opposite, the two factors have no significant influence on the absorption of 99 Tc on both Fe 2 O 3 and Fe 3 O 4 powders. The adsorption isotherms of 99 TcO 4 - on Fe, Fe 2 O 3 and Fe 3 O 4 powders can be well described by the Freundlich's equation. The major valence state of 99 Tc is deduced to be Tc(IV) when iron powders is used as the absorbent. In the case of Fe 2 O 3 or Fe 3 O 4 as an absorbent, the 99 Tc remains as the TcO 4 - form

Synthesis, characterization, and comparative gas-sensing properties of Fe{sub 2}O{sub 3} prepared from Fe{sub 3}O{sub 4} and Fe{sub 3}O{sub 4}-chitosan

Energy Technology Data Exchange (ETDEWEB)

Cuong, Nguyen Duc [Faculty of Hospitality and Tourism, Hue University, 22 Lam Hoang, Vy Da Ward, Hue City (Viet Nam); College of Sciences, Hue University, 77 Nguyen Hue, Phu Nhuan Ward, Hue City (Viet Nam); International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), Hanoi (Viet Nam); Hoa, Tran Thai; Khieu, Dinh Quang [College of Sciences, Hue University, 77 Nguyen Hue, Phu Nhuan Ward, Hue City (Viet Nam); Lam, Tran Dai [Institute of Materials Science, Vietnamese Academy of Science and Technology, Hanoi (Viet Nam); Hoa, Nguyen Duc [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), Hanoi (Viet Nam); Van Hieu, Nguyen, E-mail: hieu@itims.edu.vn [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology (HUST), Hanoi (Viet Nam)

2012-05-15

Highlights: Black-Right-Pointing-Pointer We have demonstrated a facile method to prepare Fe{sub 3}O{sub 4} nanoparticles and chitosan-coated Fe{sub 3}O{sub 4} nanoparticles. Black-Right-Pointing-Pointer {alpha}-Fe{sub 2}O{sub 3} sensors prepared from those Fe{sub 3}O{sub 4} materials have been investigated and compared. Black-Right-Pointing-Pointer The results show potential application of {alpha}-Fe{sub 2}O{sub 3} for CO sensors in environmental monitoring. - Abstract: In this paper, Fe{sub 3}O{sub 4} and chitosan (CS)-coated Fe{sub 3}O{sub 4} nanoparticles were synthesized via co-precipitation method and subsequent covalent binding of CS onto the surface for functionalization, respectively. Characterization of the crystal structures and morphologies of as-synthesized nanoparticles by X-ray diffraction, scanning electron microscopy, and transmission electron microscopy demonstrated that Fe{sub 3}O{sub 4} had a cubic spinal structure with irregular shapes and average diameters of 10-20 nm. The surface states and magnetic properties of Fe{sub 3}O{sub 4}-CS nanoparticles were characterized by Fourier transform infrared spectra and vibrating sample magnetometry. Results showed that Fe{sub 3}O{sub 4}-CS nanoparticles possessed super-paramagnetic properties, with saturated magnetization up to 60 emu/g. In addition, Fe{sub 3}O{sub 4} and CS-coated Fe{sub 3}O{sub 4} nanoparticles were used in the fabrication of {alpha}-Fe{sub 2}O{sub 3} based gas sensors. Gas sensing measurements revealed that the {alpha}-Fe{sub 2}O{sub 3} gas sensor prepared from Fe{sub 3}O{sub 4}-CS had a better response to H{sub 2}, CO, C{sub 2}H{sub 5}OH, and NH{sub 3} compared with the device prepared from pristine Fe{sub 3}O{sub 4}. Furthermore, the {alpha}-Fe{sub 2}O{sub 3} sensor prepared from Fe{sub 3}O{sub 4}-CS nanoparticles exhibited the highest response to CO among the test gases, suggesting that it has great potential for practical applications in environmental monitoring.

Sub-2 nm SnO2 nanocrystals: A reduction/oxidation chemical reaction synthesis and optical properties

International Nuclear Information System (INIS)

Zhang Hui; Du Ning; Chen Bindi; Cui Tianfeng; Yang Deren

2008-01-01

A simple reduction/oxidation chemical solution approach at room temperature has been developed to synthesize ultrafine SnO 2 nanocrystals, in which NaBH 4 is used as a reducing agent instead of mineralizers such as sodium hydroxide, ammonia, and alcohol. The morphology, structure, and optical property of the ultrafine SnO 2 nanocrystals have been characterized by high-resolution transmission electron microscopy (HRTEM), X-ray powder diffraction (XRD), differential scanning calorimetry and thermogravimetric analysis (DSC-TGA), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy. It is indicated that the uniform tetragonal ultrafine SnO 2 nanocrystals with the size below 2 nm have been fabricated at room temperature. The band gap of the ultrafine SnO 2 nanocrystals is about 4.1 eV, exhibiting 0.5 eV blue shift from that of the bulk SnO 2 (3.6 eV). Furthermore, the mechanism for the reduction/oxidation chemical reaction synthesis of the ultrafine SnO 2 nanocrystals has been preliminary presented

Microstructural features of the La1−xCaxFeO3−δ solid solutions prepared via Pechini route

International Nuclear Information System (INIS)

Gerasimov, E.Yu.; Isupova, L.A.; Tsybulya, S.V.

2015-01-01

Highlights: • La 1−x Ca x FeO (3−δ) (0 ≤ x ≤ 0.7) perovskite were prepared by Pechini method. • Planar defects in direction (1 0 1) were observed in the perovskite surface. • α-Fe 2 O 3 particles (1–10 nm) on the surface of perovskite were revealed. • Amount of α-Fe 2 O 3 particles on the perovskite surface grew with rising x values. - Abstract: Solid solutions with La 1−x Ca x FeO 3−δ (0 ≤ x ≤ 0.7) perovskite-like structure prepared via Pechini route have been investigated by using high resolution transmission electron microscopy and X-ray diffraction. Extended planar defects lying in (1 0 1) crystallographic planes and α-Fe 2 O 3 nanoparticles on the surface of perovskite microcrystals are characteristic of the samples under investigation. It was found that testing of the samples in catalytic deep CH 4 oxidation process results in partial destruction of solid solutions with formation of planar defects in the bulk and α-Fe 2 O 3 particles on the surface

Core shell structured nanoparticles of Eu3+ doped SnO2 with SiO2 shell: luminescence studies

International Nuclear Information System (INIS)

Ningthoujam, R.S.; Sudarsan, V.; Kulshreshtha, S.K.

2005-01-01

Re dispersible SnO 2 nanoparticles with and without Eu 3+ doping nanoparticles were prepared at 185 deg C by the urea hydrolysis of Sn 4+ in ethylene glycol medium. X-ray diffraction and 119 Sn MAS NMR studies of these particles revealed that these nanoparticles are crystalline with Cassiterite structure having an average crystallite size of 7 nm. Undoped SnO 2 gave a emission peak centered around 470 nm characteristic of the traps present in the nanoparticles. For Eu 3+ doped samples, emission around 590 and 615 nm was observed on both direct excitation as well as indirect excitation through traps, indicating that there is an energy transfer between the traps present in the nanoparticles and Eu 3+ ions. The asymmetric ratio of luminescence (relative intensity ratio of 590 to 615 nm transitions) has been found to be 1.2. For SnO 2 :Eu(5%)-SiO 2 nanoparticles, the asymmetric ratio of luminescence change significantly indicating the formation of nanoparticles with SnO 2 :Eu(5%) core covered with SiO 2 shell. (author)

Synthesis of mixed-valent {alpha}- and {beta}-NaFe{sub 2}O{sub 3} polymorphs under controlled partial oxygen pressure

Energy Technology Data Exchange (ETDEWEB)

Bruno, Shaun R.; Blakely, Colin K. [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States); Poltavets, Viktor V., E-mail: poltavets@chemistry.msu.edu [Department of Chemistry, Michigan State University, East Lansing, MI 48824 (United States)

2012-08-15

Synthesis of mixed valent compounds, especially when multiple polymorphs exist, requires careful control of the preparation conditions. {alpha}- and {beta}-NaFe{sub 2}O{sub 3} polymorphs were synthesized under controlled partial oxygen pressure (pO{sub 2}). pO{sub 2} regions of stability at 850 Degree-Sign C were determined for both phases for the first time. A modified oxygen buffer method was developed for the facile preparation of mixed valent oxides under controlled pO{sub 2}. {beta}-NaFe{sub 2}O{sub 3} is the only known n=2 member of the AM{sub n}O{sub n+1} (A=alkali metal, M=3d metal) rock-salt related homolog series with layered cation ordering. The possibility of new members of the homolog series with other 3d metals is considered. - Graphical abstract: Schematic section of phase composition vs. partial O{sub 2} pressure diagram at 850 Degree-Sign C for Na/Fe=1/2 and structure models of {alpha}- and {beta}-NaFe{sub 2}O{sub 3}. Highlights: Black-Right-Pointing-Pointer {alpha}- and {beta}-NaFe{sub 2}O{sub 3} polymorphs were synthesized under controlled oxygen pressure. Black-Right-Pointing-Pointer {beta}-NaFe{sub 2}O{sub 3} has rock-salt related structure with layered cation ordering. Black-Right-Pointing-Pointer Existence of the rock-salt related homolog series AM{sub n}O{sub n+1} is discussed.

Effect of Fe2O3 on the sintering and stabilization of ZrO2-MgO system

International Nuclear Information System (INIS)

Longo, E.; Paskocimas, C.A.; Ambrosecchia, J.R.; Weffort, L.C.; Baldo, J.B.; Leite, L.R.; Varela, J.A.

1990-01-01

Through X-ray diffraction, it was studied the influence of the iron oxide (Fe 2 O 3 ) as a mineralizer in the development of partially stabilized zirconia phases (cubic/tetragonal) within the system ZrO 2 -MgO. In the preparation of the studied compositions it was utilized a Brazilian comercial zirconia powder and different precursors for the MgO and Fe 2 O 3 additives. It was observed that the main effect of iron oxide consisted on the speed up of the solid solution formation process of Mg + 2 in the Zr +4 sub-lattice, as well as being a very effective sintering agent. (author) [pt

Capsule-like {alpha}-Fe{sub 2}O{sub 3} nanoparticles: Synthesis, characterization, and growth mechanism

Energy Technology Data Exchange (ETDEWEB)

Su, Changhua [College of Materials Science and Engineering, Liaocheng University (China); Wang, Hui [Key Laboratory of Synthetic and Natural Functional Molecule Chemistry of the Ministry of Education, College of Chemistry and Materials Science, Northwest University, Xi' an (China)

2012-08-15

Uniform capsule-like {alpha}-Fe{sub 2}O{sub 3} particles were synthesized via a simple hydrothermal method, employing FeCl{sub 3} and CH{sub 3}COONa as the precursors and sodium dodecyl sulfate (SDS) as soft template. X-ray powder diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy were used to characterize the structure of synthesized products. Some factors influencing the formation of capsule-like {alpha}-Fe{sub 2}O{sub 3} particles were systematically investigated, including different kinds of surfactants, the concentration of SDS, and reaction times. The investigation on the evolution formation reveals that SDS was critical to control the morphology of final products, and a possible five-step growth mechanism was presented by tracking the structures of the products at different reaction stages. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Analysis of Methanol Sensitivity on SnO2-ZnO Nanocomposite

Science.gov (United States)

Bassey, Enobong E.; Sallis, Philip; Prasad, Krishnamachar

This research reports on the sensing behavior of a nanocomposite of tin dioxide (SnO2) and zinc oxide (ZnO). SnO2-ZnO nanocomposites were fabricated into sensor devices by the radio frequency sputtering method, and used for the characterization of the sensitivity behavior of methanol vapor. The sensor devices were subjected to methanol concentration of 200 ppm at operating temperatures of 150, 250 and 350 °C. A fractional difference model was used to normalize the sensor response, and determine the sensitivity of methanol on the sensor. Response analysis of the SnO2-ZnO sensors to the methanol was most sensitive at 350 °C, followed by 250 and 150 °C. Supported by the morphology (FE-SEM, AFM) analyses of the thin films, the sensitivity behavior confirmed that the nanoparticles of coupled SnO2 and ZnO nanocomposites can promote the charge transportation, and be used to fine-tune the sensitivity of methanol and sensor selectivity to a desired target gas.

Synthesis of chelating agent free-solid phase extractor (CAF-SPE) based on new SiO2/Al2O3/SnO2 ternary oxide and application for online preconcentration of Pb2+ coupled with FAAS

International Nuclear Information System (INIS)

Tarley, César R.T.; Scheel, Guilherme L.; Zappielo, Caroline D.; Suquila, Fabio A.C.; Ribeiro, Emerson S.

2018-01-01

A new online solid phase preconcentration method using the new SiO 2 /Al2O 3 /SnO 2 ternary oxide (designated as SiAlSn) as chelating agent free-solid phase extractor (CAF-SPE) coupled to flame atomic absorption spectrometry (FAAS) for Pb 2+ determination at trace levels in different kind of samples is proposed. The solid adsorbent has been characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray fluorescence spectroscopy (XRF) and textural data. The method involves the preconcentration using time-based sampling of Pb 2+ solution at pH 4.3 through 100.0 mg of packed adsorbed into a mini-column under flow rate of 4.0 mL min -1 during 5 min. The elution step was accomplished by using 1.0 mol L -1 HCl. A wide range of analytical curve (5.0-400.0 μg L -1 ), high enrichment factor (40.5), low consumption index (0.5 mL) and low limits of quantification and detection, 5.0 and 1.5 μg L -1 , respectively, were obtained with the developed method. Practical application of method was tested on water samples, chocolate powder, Ginkgo biloba and sediment (certified reference material). On the basis of the results, the SiAlSn can be considered an effective adsorbent belonging to the class of CAF-SPE for Pb 2+ determination from different matrices. (author)

Synthesis and physical properties of the CuFe{sub 2−x}Mn{sub x}O{sub 4} (0 ≤ x ≤ 2) solid solution

Energy Technology Data Exchange (ETDEWEB)

Helaïli, N. [Laboratory of Storage and Valorization of Renewable Energies, Faculty of Chemistry, U.S.T.H.B., BP 32 El-Alia, 16111 Algiers (Algeria); Centre of Research in Physical and Chemical Analysis (CRAPC), BP 248, RP 16004 Algiers (Algeria); Bessekhouad, Y., E-mail: ybessekhouad@yahoo.fr [Laboratory of Storage and Valorization of Renewable Energies, Faculty of Chemistry, U.S.T.H.B., BP 32 El-Alia, 16111 Algiers (Algeria); National Veterinary High School, BP 161-El Harrach, Algiers (Algeria); Bachari, K. [Centre of Research in Physical and Chemical Analysis (CRAPC), BP 248, RP 16004 Algiers (Algeria); Trari, M. [Laboratory of Storage and Valorization of Renewable Energies, Faculty of Chemistry, U.S.T.H.B., BP 32 El-Alia, 16111 Algiers (Algeria)

2014-12-15

The CuFe{sub 2−x}Mn{sub x}O{sub 4} (0 ≤ x ≤ 2) solid solutions have been prepared by direct solid state reaction and the dependence of optical, electrical and electrochemical properties on the composition has been investigated. All samples exhibited the formation of a unique cubic phase irrespective of the composition with crystallite sizes on the order of 44 nm. Mn is localized in both octahedral and tetrahedral sites, and forms Mn{sup 3+}–O{sup 2−} complexes. The CuFe{sub 2−x}Mn{sub x}O{sub 4} system exhibits a p-type conductivity with indirect transition band gaps that decrease from 1.54 to 1.28 eV. Charge transport occurs either between Fe{sup 2+}/Fe{sup 3+} or Mn{sup 2+}/Mn{sup 3+} ions in B-sites according to the x value, and the conduction mechanism is controlled by small polaron hopping with a thermal activation of the mobility (μ), which is in the order of ∼10{sup −5} cm{sup 2} V{sup −1}s{sup −1} and does not depend on x. The conduction bands are particularly affected by the Mn introduction and the potentials can shift by as much as 0.5 eV. Finally, the CuFe{sub 2−x}Mn{sub x}O{sub 4} system was used as a bulk electrode in a photoelectrochemical cell and as a microphotoelectrode for H{sub 2}-production. CuFe{sub 1.6}Mn{sub 0.4}O{sub 4} demonstrates the best quantum conversion efficiency in terms of electricity (η = 0.21) and H{sub 2}-production (η{sup ∗} = 1.59). - Highlights: • The CuFe{sub 2−x}Mn{sub x}O{sub 4} (0 ≤ x ≤ 2) solid solutions have been prepared by solid state reaction. • CuFe{sub 2−x}Mn{sub x}O{sub 4} system exhibits p-type conductivity with indirect transition band gaps. • The charge transport occurs either between Fe{sup 2+}/Fe{sup 3+} or Mn{sup 2+}/Mn{sup 3+} ions in B-sites. • CuFe{sub 1.6}Mn{sub 0.4}O{sub 4} demonstrates the best quantum conversion efficiency {η"∗(H_2) = 1.59}.

Hydrogen Production from Ethanol Steam Reforming over SnO2-K2O/Zeolite Y Catalyst

International Nuclear Information System (INIS)

Lee, Jun Sung; Kim, Ji Eun; Kang, Mi Sook

2011-01-01

The SnO 2 with a particle size of about 300 nm instead of Ni is used in this study to overcome rapid catalytic deactivation by the formation of a NiAl 2 O 4 spinal structure on the conventional Ni/γ-Al 2 O 3 catalyst and simultaneously impregnated the catalyst with potassium (K). The SnO 2 -K 2 O impregnated Zeolite Y catalyst (SnO 2 -K 2 O/ZY) exhibited significantly higher ethanol reforming reactivity that that achieved with SnO 2 100 and SnO 2 30 wt %/ZY catalysts. The main products from ethanol steam reforming (ESR) over the SnO 2 -K 2 O/ ZY catalyst were H 2 , CO 2 , and CH 4 , with no evidence of any CO molecule formation. The H 2 production and ethanol conversion were maximized at 89% and 100%, respectively, over SnO 2 30 wt %-K 2 O 3.0 wt %/ZY at 600 .deg. C for 1 h at a CH 3 CH 2 OH:H 2 O ratio of 1:1 and a gas hourly space velocity (GHSV) of 12,700 h -1 . No catalytic deactivation occurred for up to 73 h. This result is attributable to the easier and weaker of reduction of Sn components and acidities over SnO 2 -K 2 O/ZY catalyst, respectively, than those of Ni/γ-Al 2 O 3 catalysts

Ultraviolet photodetectors made from SnO2 nanowires

International Nuclear Information System (INIS)

Wu, Jyh-Ming; Kuo, Cheng-Hsiang

2009-01-01

SnO 2 nanowires can be synthesized on alumina substrates and formed into an ultraviolet (UV) photodetector. The photoelectric current of the SnO 2 nanowires exhibited a rapid photo-response as a UV lamp was switched on and off. The ratio of UV-exposed current to dark current has been investigated. The SnO 2 nanowires were synthesized by a vapor-liquid-solid process at a temperature of 900 o C. It was found that the nanowires were around 70-100 nm in diameter and several hundred microns in length. High-resolution transmission electron microscopy (HRTEM) image indicated that the nanowires grew along the [200] axis as a single crystallinity. Cathodoluminescence (CL), thin-film X-ray diffractometry, and X-ray photoelectron spectroscopy (XPS) were used to characterize the as-synthesized nanowires.

Flexible Fe2O3 and V2O5 nanofibers as binder-free electrodes for high-performance all-solid-state asymmetric supercapacitors.

Science.gov (United States)

Jiang, He; Niu, Hao; Yang, Xue; Sun, Zhiqin; Li, Fuzhi; Wang, Qian; Qu, Fengyu

2018-04-16

Flexible highly porous Fe2O3 and V2O5 nanofibers are synthesized by a facile electrospinning method followed by calcination treatment and directly used as binder-free electrodes for high-performance supercapacitors. These Fe2O3 and V2O5 nanofibers interconnect with each other and construct three-dimensional hierarchical porous films with high specific surface area. Benefiting from the unique structural features, the intriguing binder-free Fe2O3 and V2O5 porous nanofiber electrodes possess high specific capacitance of 255 F g-1 and 256 F g-1 at 2 mV s-1 in 1 M Na2SO4 electrolyte, respectively. An all-solid-state asymmetric supercapacitor is fabricated using Fe2O3 and V2O5 nanofibers as negative and positive electrodes, respectively, and the all-solid-state asymmetric supercapacitor can be operated up to 1.8 V attributed to the wide and opposite potential window of both electrodes. The assembled all-solid-state asymmetric supercapacitor achieves a high energy density up to 32.2 Wh kg-1 at an average power density of 128.7 W kg-1 as well as excellent cycling stability and power capability. The effective and facile synthesis method and superior electrochemical performance provided in this work make electrospun Fe2O3 and V2O5 nanofibers promising electrode materials for high performance asymmetric supercapacitors. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis, Characterization, and Photocatalytic Activity of Zn-Doped SnO2/Zn2SnO4 Coupled Nanocomposites

Directory of Open Access Journals (Sweden)

Tiekun Jia

2014-01-01

Full Text Available Zn-doped SnO2/Zn2SnO4 nanocomposites were prepared via a two-step hydrothermal synthesis method. The as-prepared samples were characterized by X-ray diffraction (XRD, field-emission scanning electron microscopy (FESEM, transmission electron microscopy (TEM, UV-vis diffuse reflection spectroscopy, and adsorption-desorption isotherms. The results of FESEM and TEM showed that the as-prepared Zn-doped SnO2/Zn2SnO4 nanocomposites are composed of numerous nanoparticles with the size ranging from 20 nm to 50 nm. The specific surface area of the as-prepared Zn-doped SnO2/Zn2SnO4 nanocomposites is estimated to be 71.53 m2/g by the Brunauer-Emmett-Teller (BET method. The photocatalytic activity was evaluated by the degradation of methylene blue (MB, and the resulting showed that Zn-doped SnO2/Zn2SnO4 nanocomposites exhibited excellent photocatalytic activity due to their higher specific surface area and surface charge carrier transfer.

Fabrication of novel SnO2 nanofibers bundle and their optical properties

International Nuclear Information System (INIS)

Butt, Faheem K.; Cao, Chuanbao; Khan, Waheed S.; Ali, Zulfiqar; Mahmood, Tariq; Ahmed, R.; Hussain, Sajad; Nabi, Ghulam

2012-01-01

Here we report on the synthesis of novel SnO 2 nanofibers bundle (NFB) by using ball milled Fe powders via chemical vapor deposition (CVD). The reaction was carried out in a horizontal tube furnace (HTF) at 1100 °C under Ar flow. The as prepared product was characterized by X-ray diffraction (XRD), scanning electron microscopy, energy dispersive X-ray spectroscopy, transmission electron microscopy, high resolution transmission electron microscopy and selected area electron diffraction (SAED). The microscopy analysis reveals the existence of tubular structure that might be formed by the accumulation of nanofibers. The Raman spectrum reveals that the product is rutile SnO 2 with additional peaks ascribed to defects or oxygen vacancies. Room temperature Photoluminescence (PL) spectrum exhibits three emission bands at 369, 450 and 466.6 nm. Using optical absorbance data, a direct optical bandgap of 3.68 eV was calculated. -- Graphical abstract: Novel SnO 2 nanofibers bundle (NFB) fabricated via CVD method. Field emission scanning electron microscopy image of novel SnO 2 NFB and their room temperature PL emission. Highlights: ► Synthesis of novel SnO 2 nanofibers bundle at 1100 °C under partial flow of Ar gas. ► A VLS mechanism is proposed for the formation of SnO 2 nanofibers. ► The PL spectrum exhibits three emission bands at 369, 450 and 466.6 nm. ► A direct optical bandgap of 3.68 eV was calculated.

Synthesis and characterization of Sr{sub 2}Ir{sub 1-x}M{sub x}O{sub 4} (M=Ti, Fe, Co) solid solutions

Energy Technology Data Exchange (ETDEWEB)

Gatimu, Alvin J.; Berthelot, Romain; Muir, Sean; Sleight, Arthur W. [Department of Chemistry, Oregon State University, Corvallis, OR 97331 (United States); Subramanian, M.A., E-mail: mas.subramanian@oregonstate.edu [Department of Chemistry, Oregon State University, Corvallis, OR 97331 (United States)

2012-06-15

The effects of Ti, Fe and Co substitutions for Ir on the structure and on the physical properties of Sr{sub 2}IrO{sub 4} are investigated. A complete solid solution Sr{sub 2}Ir{sub 1-x}Ti{sub x}O{sub 4} is obtained while both Fe and Co doping are relatively limited. In each case however, the c-axis cell parameter and the initial IrO{sub 6} octahedra tilting decreases with substitution. Doping with Ti, Fe and Co results in a decrease of the magnetic susceptibility and in an increase in the paramagnetic effective moment for Co and Fe doped samples and a suppression of the weak ferromagnetic ordering observed for Sr{sub 2}IrO{sub 4}. - Graphical abstract: Solid solutions of Sr{sub 2}Ir{sub 1-x}M{sub x}O{sub 4} (M=Ti, Fe, Co) have been synthesized and characterized by powder X-ray diffraction, magnetism and electrical measurements. Changes in the a parameter and decreases in both the c-axis cell parameters and the initial IrO{sub 6} octahedra tilting are found to be correlated. Highlights: Black-Right-Pointing-Pointer Solid Solutions of Sr{sub 2}Ir{sub 1-x}M{sub x}O{sub 4} (M=Ti, Fe, Co) are synthesized. Black-Right-Pointing-Pointer The Sr{sub 2}Ir{sub 1-x}Ti{sub x}O{sub 4} solid solution is complete while those of Fe and Co are relatively limited. Black-Right-Pointing-Pointer The change in a cell parameter with substitution is much less than that of the c parameter. Black-Right-Pointing-Pointer Decreased tilting and the smaller size of the M cation contrastingly affect the a parameter. Black-Right-Pointing-Pointer Doping results in a suppression of the weak ferromagnetic ordering in Sr{sub 2}IrO{sub 4}.

Sensing mechanism of SnO2/ZnO nanofibers for CH3OH sensors: heterojunction effects

International Nuclear Information System (INIS)

Tang, Wei

2017-01-01

SnO 2 /ZnO composite nanofibers were synthesized by a simple electrospinning method. The prepared SnO 2 /ZnO gas sensors exhibited good linear and high response to methanol. The enhanced sensing behavior of SnO 2 /ZnO might be associated with the homotypic heterojunction effects formed in n -SnO 2 / n -ZnO nanograins boundaries. In addition, the possible sensing mechanisms of methanol on SnO 2 /ZnO surface were investigated by density functional theory in order to make the methanol adsorption and desorption process clear. Zn doped SnO 2 model was adopted to approximate the SnO 2 /ZnO structure because of the calculation power limitations. Calculation results showed that when exposed to methanol, the methanol would react with bridge oxygen O 2c , planar O 3c and pre adsorbed oxygen vacancy on the lattice surface. The –CH 3 and –OH of methanol molecule would both lose one H atom. The lost H atoms bonded with oxygen at the adsorption sites. The final products were HCHO and H 2 O. Electrons were transferred from methanol to the lattice surface to reduce the resistance of semiconductor gas sensitive materials, which is in agreement with the experimental phenomena. More adsorption models of other interfering gases, such as ethanol, formaldehyde and acetone will be built and calculated to explain the selectivity issue from the perspective of adsorption energy, transferred charge and density of states in the future work. (paper)

Fabrication of a transparent ultraviolet detector by using n-type Ga2O3 and p-type Ga-doped SnO2 core-shell nanowires.

Science.gov (United States)

Hsu, Cheng-Liang; Lu, Ying-Ching

2012-09-21

This study investigates the feasibility of synthesizing high-density transparent Ga(2)O(3)/SnO(2):Ga core-shell nanowires on a sapphire substrate at 1000 °C by VLS. The doping Ga concentrations are 0.46, 1.07, 2.30 and 17.53 atomic%. The XRD spectrum and HR-TEM reveal Ga(2)O(3) and SnO(2) as having monoclinic and tetragonal rutile structures, respectively. Experimental results indicate that the XRD peak shift of SnO(2) to a larger angle increases with the increasing amount of Ga doping. According to the CL spectrum, SnO(2) and Ga(2)O(3) peak at approximately 528-568 nm and 422-424 nm, respectively. The maximum quantum efficiency of Ga(2)O(3)/SnO(2):Ga core-shell nanowires is around 0.362%. The UV light on-off current contrast ratio of Ga(2)O(3)/SnO(2):Ga core-shell nanowires is around 1066.7 at a bias of 5 V. Moreover, the dynamic response of Ga(2)O(3)/SnO(2):Ga core-shell nanowires has an on-off current contrast ratio of around 16. Furthermore, the Ga(2)O(3) region functions similar to a capacitor and continues to accumulate SnO(2):Ga excited electrons under UV light exposure.

Synthesis And Characterization Of SiO2, SnO2 And TiO2 Metal Oxide Shells Covering Cu2O Particles

Directory of Open Access Journals (Sweden)

Yu Ri

2015-06-01

Full Text Available In this work is described a means of improving the chemical stability of Cu2O@SiO2, Cu2O@SnO2 and Cu2O@TiO2 materials. The SiO2, SnO2 and TiO2 coated samples were stable from pH 3 to pH 10 for up to seven days. To determine the stability of the coated nanoparticles, and their colloidal solutions under acidic and basic conditions, colloidal nanoparticle solutions with various pH values were prepared and monitored over time. Details of the effect of variations in pH on the phase stability of core-shell type Cu2O were characterized using transmission electron microscopy and X-ray diffraction.

Chemical quenching of positronium in Fe2O3/Al2O3 catalysts

International Nuclear Information System (INIS)

Li, C.; Zhang, H.J.; Chen, Z.Q.

2010-01-01

Fe 2 O 3 /Al 2 O 3 catalysts were prepared by solid state reaction method using α-Fe 2 O 3 and γ-Al 2 O 3 nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ 3 and τ 4 are attributed to positronium annihilation in two types of pores distributed inside Al 2 O 3 grain and between the grains, respectively. With increasing Fe 2 O 3 content from 3 wt% to 40 wt%, the lifetime τ 3 keeps nearly unchanged, while the longest lifetime τ 4 shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe 2 O 3 content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ 4 is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.

Chemical quenching of positronium in Fe 2O 3/Al 2O 3 catalysts

Science.gov (United States)

Li, C.; Zhang, H. J.; Chen, Z. Q.

2010-09-01

Fe 2O 3/Al 2O 3 catalysts were prepared by solid state reaction method using α-Fe 2O 3 and γ-Al 2O 3 nano powders. The microstructure and surface properties of the catalyst were studied using positron lifetime and coincidence Doppler broadening annihilation radiation measurements. The positron lifetime spectrum shows four components. The two long lifetimes τ3 and τ4 are attributed to positronium annihilation in two types of pores distributed inside Al 2O 3 grain and between the grains, respectively. With increasing Fe 2O 3 content from 3 wt% to 40 wt%, the lifetime τ3 keeps nearly unchanged, while the longest lifetime τ4 shows decrease from 96 ns to 64 ns. Its intensity decreases drastically from 24% to less than 8%. The Doppler broadening S parameter shows also a continuous decrease. Further analysis of the Doppler broadening spectra reveals a decrease in the p-Ps intensity with increasing Fe 2O 3 content, which rules out the possibility of spin-conversion of positronium. Therefore the decrease of τ4 is most probably due to the chemical quenching reaction of positronium with Fe ions on the surface of the large pores.

Solid state reaction studies in Fe3O4–TiO2 system by diffusion couple method

International Nuclear Information System (INIS)

Ren, Zhongshan; Hu, Xiaojun; Xue, Xiangxin; Chou, Kuochih

2013-01-01

Highlights: •The solid state reactions of Fe2O3-TiO2 system was studied by the diffusion couple method. •Different products were formed by diffusion, and the FeTiO3 was more stable phase. •The inter-diffusion coefficients and diffusion activation energy were estimated. -- Abstract: The solid state reactions in Fe 3 O 4 –TiO 2 system has been studied by diffusion couple experiments at 1323–1473 K, in which the oxygen partial pressure was controlled by the CO–CO 2 gas mixture. The XRD analysis was used to confirm the phases of the inter-compound, and the concentration profiles were determined by electron probe microanalysis (EPMA). Based on the concentration profile of Ti, the inter-diffusion coefficients in Fe 3 O 4 phase, which were both temperature and concentration of Ti ions dependent, were calculated by the modified Boltzmann–Matano method. According to the relation between the thickness of diffusion layer and temperature, the diffusion coefficient of the Fe 3 O 4 –TiO 2 system was obtained. According to the Arrhenius equation, the estimated diffusion activation energy was about 282.1 ± 18.8 kJ mol −1

Sensing mechanism of SnO2/ZnO nanofibers for CH3OH sensors: heterojunction effects

Science.gov (United States)

Tang, Wei

2017-11-01

SnO2/ZnO composite nanofibers were synthesized by a simple electrospinning method. The prepared SnO2/ZnO gas sensors exhibited good linear and high response to methanol. The enhanced sensing behavior of SnO2/ZnO might be associated with the homotypic heterojunction effects formed in n-SnO2/n-ZnO nanograins boundaries. In addition, the possible sensing mechanisms of methanol on SnO2/ZnO surface were investigated by density functional theory in order to make the methanol adsorption and desorption process clear. Zn doped SnO2 model was adopted to approximate the SnO2/ZnO structure because of the calculation power limitations. Calculation results showed that when exposed to methanol, the methanol would react with bridge oxygen O2c , planar O3c and pre adsorbed oxygen vacancy on the lattice surface. The -CH3 and -OH of methanol molecule would both lose one H atom. The lost H atoms bonded with oxygen at the adsorption sites. The final products were HCHO and H2O. Electrons were transferred from methanol to the lattice surface to reduce the resistance of semiconductor gas sensitive materials, which is in agreement with the experimental phenomena. More adsorption models of other interfering gases, such as ethanol, formaldehyde and acetone will be built and calculated to explain the selectivity issue from the perspective of adsorption energy, transferred charge and density of states in the future work.

Investigations on FCAM-III (Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36): A new homologue of the aenigmatite structure-type in the system CaO-MgO-Fe2O3-Al2O3

Science.gov (United States)

Zöll, Klaus; Kahlenberg, Volker; Krüger, Hannes; Tropper, Peter

2018-02-01

In the course of a systematic study of a part of the quaternary system Fe2O3-CaO-Al2O3-MgO (FCAM) the previously unknown compound Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 (FCAM-III) has been synthesized. By analogy with the so-called SFCA series [1-5], our investigation in the system of FCAM shows the existence of a stoichiometric homologous series M14+6nO20+8n, where M = Fe, Ca, Al, Mg and n = 1 or 2. In air, we can prove the formation of coexisting FCAM-III and FCAM-I solid solutions at 1400 °C. By increasing the temperature up to 1425 °C FCAM-I disappears completely and FCAM-III co-exists with magnesiumferrite and a variety of calcium iron oxides. At 1450 °C FCAM-III breaks down to a mixture of FCAM-I again as well as magnesioferrite and melt. Small single-crystals of FCAM-III up to 35 μm in size could be retrieved from the 1425 °C experiment and were subsequently characterized using electron microprobe analysis and synchroton X-ray single-crystal diffraction. Finally the Fe2+/Fetot ratio was calculated from the total iron content based on the crystal-chemical formula obtained from EMPA measurements and charge balance considerations. FCAM-III or Ca2.38Mg2.09Fe3+10.61Fe2+1.59Al9.33O36 has a triclinic crystal structure (space group P 1 ̅). The basic crystallographic data are: a = 10.223(22) Å, b = 10.316(21) Å, c = 14.203(15) Å, α = 93.473(50)°, β = 107.418(67)°, γ = 109.646(60)°, V = 1323.85(2) ų, Z = 1. Using Schreinemaker's technique to analyze the phase relations in the system Fe2O3-CaO-Al2O3-MgO it was possible to obtain the semi-quantitative stability relations between the participating phases and construct a topologically correct phase sequence as a function of T and fO2. The analysis shows that Ca2Al0.5Fe1.5O5 (C2A0.25F0.75) and CaAl1.5Fe2.5O7 (CA0.75F1.25) with higher calculated Fe2+ contents are preferably formed at lower oxygen fugacity and react to CaAl0.5Fe1.5O4 (CA0.25F0.75) by increasing fO2. Spinel-type magnesium

Experimental Investigation and Thermodynamic Modeling of the B2O3-FeO-Fe2O3-Nd2O3 System for Recycling of NdFeB Magnet Scrap

Science.gov (United States)

Jakobsson, Lars Klemet; Tranell, Gabriella; Jung, In-Ho

2017-02-01

NdFeB magnet scrap is an alternative source of neodymium that could have a significantly lower impact on the environment than current mining and extraction processes. Neodymium can be readily oxidized in the presence of oxygen, which makes it easy to recover neodymium in oxide form. Thermochemical data and phase diagrams for neodymium oxide containing systems is, however, very limited. Thermodynamic modeling of the B2O3-FeO-Fe2O3-Nd2O3 system was hence performed to obtain accurate phase diagrams and thermochemical properties of the system. Key phase diagram experiments were also carried out for the FeO-Nd2O3 system in saturation with iron to improve the accuracy of the present modeling. The modified quasichemical model was used to describe the Gibbs energy of the liquid oxide phase. The Gibbs energy functions of the liquid phase and the solids were optimized to reproduce all available and reliable phase diagram data, and thermochemical properties of the system. Finally the optimized database was applied to calculate conditions for selective oxidation of neodymium from NdFeB magnet waste.

Insights into the electrochemical activity of nanosized {alpha}-LiFeO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Morales, J.; Santos-Pena, J.; Trocoli, R. [Departamento de Quimica Inorganica e Ingenieria Quimica, Edificio Marie Curie, Campus de Rabanales, Universidad de Cordoba, Cordoba 14071 (Spain); Franger, S. [Laboratoire de Physico-Chimie de l' Etat Solide, ICMMO, Universite Paris XI, Orsay 91405 (France); Rodriguez-Castellon, E. [Departamento de Quimica Inorganica, Cristalografia y Mineralogia, Campus de Teatinos, Universidad de Malaga, Malaga 29071 (Spain)

2008-09-20

In recent work [J. Morales, J. Santos-Pena, Electrochem. Commun. 9 (2007) 2116], we prepared nanosized {alpha}-LiFeO{sub 2} with increased electrochemical activity in lithium cells relative to various lithium ferrite polymorphs. In this work, we studied the previous electrodes in different charge states in order to obtain a more accurate picture of the phenomena occurring during cycling. Exsitu X-ray photoelectron spectroscopy (XPS) measurements confirmed the oxidation/reduction of iron atoms during the charge/discharge process. The electrochemical impedance spectroscopy results suggested that the electrolyte is not oxidised during the first charge, but rather than a solid electrolyte interface is formed after one cycle. Also, thermal tests revealed that Fe(IV) present in the electrodes reacted with the electrolyte to form oxidised carbon species. Finally, {alpha}-LiFeO{sub 2} was tested as a positive electrode material in a lithium battery under different regimes. Stabilised capacities up to 150 mAh g{sup -1} were obtained under a C/4 regime. This lithium ferrite is therefore an attractive alternative to LiCoO{sub 2}. (author)

Synthesis, structural and luminescent aspect of Tb3+ doped Sr2SnO4 phosphor

International Nuclear Information System (INIS)

Taikar, Deepak R.

2016-01-01

A novel green emitting, Tb 3+ doped Sr 2 SnO 4 phosphor was synthesized by the co-precipitation method and its photoluminescence characterization was performed. Sr 2 SnO 4 has an ordered tetragonal K 2 NiF 4 -type structure with space group I4/mmm. The structure of Sr 2 SnO 4 consists of SnO 6 octahedra. From the structure of Sr 2 SnO 4 , it was observed that the sites of Sn 4+ ions have inverse symmetry while the Sr 2+ ions have the low symmetry. X-ray powder diffraction (XRD) analysis confirmed the formation of Sr 2 SnO 4 :Tb 3+ . Photoluminescence measurements showed that the phosphor exhibited bright green emission at about 543 nm attributed to 5 D 4 à 7 F 5 transition of Tb 3+ ion under UV excitation. The emission spectra did not exhibit conventional blue emission peaks of Tb 3+ ions due to 5 D 3 → 7 F J transitions in the spectral region 350-470 nm. The excitation spectra indicate that this compound may be useful as a lamp phosphor. (author)

Investigations of the physical and chemical properties of solid solutions Pb/Mnsub(1/2), Nbsub(1/2)/O3 - PbTiO3 - PbZrO3

International Nuclear Information System (INIS)

Szadkowska, A.; Majewska-Pilchowska, K.

1981-01-01

The preparation of the PMTZ materials on the basis of solid solutions Pb/Mnsub(1/2)/O 3 - PbTiO 3 - PbZrO 3 has been described. The X-ray analysis of the examined materials has been made, and porosity and grain size have been determined. Dielectric constant and mechanical quality factor as a function of PbZrO 3 content have been determined. The obtained results indicate that solid solutions Pb/Mnsub(1/2), Nbsub(1/2)/O 3 - PbTiO 3 - PbZrO 3 are useful piezoelectric materials. (author)

Effect of Fe2O3 and Binder on the Electrochemical Properties of Fe2O3/AB (Acetylene Black) Composite Electrodes

Science.gov (United States)

Anh, Trinh Tuan; Thuan, Vu Manh; Thang, Doan Ha; Hang, Bui Thi

2017-06-01

In an effort to find the best anode material for Fe/air batteries, a Fe2O3/AB (Acetylene Black) composite was prepared by dry-type ball milling using Fe2O3 nanoparticles and AB as the active and additive materials, respectively. The effects of various binders and Fe2O3 content on the electrochemical properties of Fe2O3/AB electrodes in alkaline solution were investigated. It was found that the content of Fe2O3 strongly affected the electrochemical behavior of Fe2O3/AB electrodes; with Fe2O3 nanopowder content reaching 70 wt.% for the electrode and showing improvement of the cyclability. When the electrode binder polytetrafluoroethylene (PTFE) was used, clear redox peaks were observed via cyclic voltammetry (CV), while polyvinylidene fluoride-containing electrodes provided CV curves with unobservable redox peaks. Increasing either binder content in the electrode showed a negative effect in terms of the cyclability of the Fe2O3/AB electrode.

Electrolytically exfoliated graphene-loaded flame-made Ni-doped SnO2 composite film for acetone sensing.

Science.gov (United States)

Singkammo, Suparat; Wisitsoraat, Anurat; Sriprachuabwong, Chakrit; Tuantranont, Adisorn; Phanichphant, Sukon; Liewhiran, Chaikarn

2015-02-11

In this work, flame-spray-made SnO2 nanoparticles are systematically studied by doping with 0.1-2 wt % nickel (Ni) and loading with 0.1-5 wt % electrolytically exfoliated graphene for acetone-sensing applications. The sensing films (∼12-18 μm in thickness) were prepared by a spin-coating technique on Au/Al2O3 substrates and evaluated for acetone-sensing performances at operating temperatures ranging from 150 to 350 °C in dry air. Characterizations by X-ray diffraction, transmission/scanning electron microscopy, Brunauer-Emmett-Teller analysis, X-ray photoelectron spectroscopy and Raman spectroscopy demonstrated that Ni-doped SnO2 nanostructures had a spheriodal morphology with a polycrystalline tetragonal SnO2 phase, and Ni was confirmed to form a solid solution with SnO2 lattice while graphene in the sensing film after annealing and testing still retained its high-quality nonoxidized form. Gas-sensing results showed that SnO2 sensing film with 0.1 wt % Ni-doping concentration exhibited an optimal response of 54.2 and a short response time of ∼13 s toward 200 ppm acetone at an optimal operating temperature of 350 °C. The additional loading of graphene at 5 wt % into 0.1 wt % Ni-doped SnO2 led to a drastic response enhancement to 169.7 with a very short response time of ∼5.4 s at 200 ppm acetone and 350 °C. The superior gas sensing performances of Ni-doped SnO2 nanoparticles loaded with graphene may be attributed to the large specific surface area of the composite structure, specifically the high interaction rate between acetone vapor and graphene-Ni-doped SnO2 nanoparticles interfaces and high electronic conductivity of graphene. Therefore, the 5 wt % graphene loaded 0.1 wt % Ni-doped SnO2 sensor is a promising candidate for fast, sensitive and selective detection of acetone.

The phase diagram and magnetic properties of Co and Ti co-doped (1−x)BiFeO_3–xLaFeO_3 solid solutions

International Nuclear Information System (INIS)

Wu, Jiangtao; Xu, Jun; Li, Nan; Jiang, Yaqi; Xie, Zhaoxiong

2015-01-01

Single phase Co and Ti co-doped Bi_1_−_xFeO_3−La_xFeO_3 (x = 0–1) solid solutions were prepared by the sol–gel method. Room temperature x-ray powder diffraction (XRD) patterns showed that the structures of as-prepared Bi_1_−_xLa_xFe_0_._9_0Co_0_._0_5Ti_0_._0_5O_3 solid solutions transformed from rhombohedral R3c to tetragonal P4mm and then to orthorhombic Pnma, with increasing La concentration from 0 to 1. In situ high-temperature XRD (HTXRD) analysis further revealed that rhombohedral structure R3c (x ≤ 0.16) and tetragonal structure P4mm (0.17 ≤ x ≤ 0.40) changed to orthorhombic Pnma along with increasing temperature, and the phase transition temperature decreased with the increase of La doping concentration. However, the orthorhombic structure Pnma (x ≥ 0.41) kept stable even when the temperature reached 850 °C. The phase diagram of as-prepared binary solid solutions of Bi_1_−_xLa_xFe_0_._9_0Co_0_._0_5Ti_0_._0_5O_3(x = 0–1) was drawn on the basis of XRD and HTXRD analysis. Magnetic measurement revealed that the magnetic properties are greatly enhanced with the increase of La content. - Highlights: • Single phase Co and Ti co-doped (1−x)BiFeO_3–xLaFeO_3 (x = 0–1) solid solutions were synthesized. • The phase transitions were investigated by tuning composition and temperature. • Phase diagram was constructed according to the results of XRD for the first time. • The magnetization of solid solution can be enhanced when increasing La content.

Magnetoelectric effect in (BiFeO3x–(BaTiO31-x solid solutions

Directory of Open Access Journals (Sweden)

Kowal Karol

2015-03-01

Full Text Available The aim of the present work was to study magnetoelectric effect (ME in (BiFeO3x-(BaTiO31-x solid solutions in terms of technological conditions applied in the samples fabrication process. The rapidly growing interest in these materials is caused by their multiferroic behaviour, i.e. coexistence of both electric and magnetic ordering. It creates possibility for many innovative applications, e.g. in steering the magnetic memory by electric field and vice versa. The investigated samples of various chemical compositions (i.e. x = 0.7, 0.8 and 0.9 were prepared by the solid-state sintering method under three sets of technological conditions differing in the applied temperature and soaking time. Measurements of the magnetoelectric voltage coefficient αME were performed using a dynamic lock-in technique. The highest value of αME was observed for 0.7BiFeO3-0.3BaTiO3 solid solution sintered at the highest temperature (T = 1153 K after initial electrical poling despite that the soaking time was reduced 10 times in this case.

Novel microwave-assisted synthesis of porous g-C3N4/SnO2 nanocomposite for solar water-splitting

Science.gov (United States)

Seza, A.; Soleimani, F.; Naseri, N.; Soltaninejad, M.; Montazeri, S. M.; Sadrnezhaad, S. K.; Mohammadi, M. R.; Moghadam, H. Asgari; Forouzandeh, M.; Amin, M. H.

2018-05-01

Highly porous nanocomposites of graphitic-carbon nitride and tin oxide (g-C3N4/SnO2) were prepared through simple pyrolysis of urea molecules under microwave irradiation. The initial amount of tin was varied in order to investigate the effect of SnO2 content on preparation and properties of the composites. The synthesized nanocomposites were well-characterized by XRD, FE-SEM, HR-TEM, BET, FTIR, XPS, DRS, and PL. A homogeneous distribution of SnO2 nanoparticles with the size of less than 10 nm on the porous C3N4 sheets could be obtained, suggesting that in-situ synthesis of SnO2 nanoparticles was responsible for the formation of g-C3N4. The process likely occurred by the aid of the large amounts of OH groups formed on the surfaces of SnO2 nanoparticles during the polycondensation reactions of tin derivatives which could facilitate the pyrolysis of urea to carbon nitride. The porous nanocomposite prepared with initial tin amount of 0.175 g had high specific surface area of 195 m2 g-1 which showed high efficiency photoelectrochemical water-splitting ability. A maximum photocurrent density of 33 μA cm-2 was achieved at an applied potential of 0.5 V when testing this nanocomposite as photo-anode in water-splitting reactions under simulated visible light irradiation, introducing it as a promising visible light photoactive material.

Preparation of Mesoporous SnO2 by Electrostatic Self-Assembly

Directory of Open Access Journals (Sweden)

Yang Jing

2014-01-01

Full Text Available We report a simple and scalable strategy to synthesize mesoporous SnO2 with tin dioxide nanoparticles of 5-6 nm crystalline walls and 3-4 nm pore diameter with the assistance of Mo7O246- as templating agent at room temperature. The samples were characterized by XRD, TEM, UV-DRS, XPS, and BET. The product has a moderately high surface area of 132 m2 g−1 and a narrow mesoporous structure with an average pore diameter of 3.5 nm. The photocatalytic activities of the mesoporous SnO2 were evaluated by the degradation of methyl orange (MO in aqueous solution under UV light irradiation.

Hierarchical architectures of ZnS–In2S3 solid solution onto TiO2 nanofibers with high visible-light photocatalytic activity

International Nuclear Information System (INIS)

Liu, Chengbin; Meng, Deshui; Li, Yue; Wang, Longlu; Liu, Yutang; Luo, Shenglian

2015-01-01

Graphical abstract: A unique hierarchical architecture of ZnS–In 2 S 3 solid solution onto TiO 2 nanofibers was fabricated. The hierarchical heterostructures exhibit high visible light photocatalytic activity and outstanding recycling performance. - Highlights: • Novel hierarchical heterostructure of TiO 2 @ZnS–In 2 S 3 solid solution. • Efficient inhibition of ZnS–In 2 S 3 solid solution aggregation. • High visible light photocatalytic activity. • Highly stable recycling performance. - Abstract: A unique hierarchical architecture of ZnS–In 2 S 3 solid solution nanostructures onto TiO 2 nanofibers (TiO 2 @ZnS–In 2 S 3 ) has been successfully fabricated by simple hydrothermal method. The ZnS–In 2 S 3 solid solution nanostructures exhibit a diversity of morphologies: nanosheet, nanorod and nanoparticle. The porous TiO 2 nanofiber templates effectively inhibit the aggregation growth of ZnS–In 2 S 3 solid solution. The formation of ZnS–In 2 S 3 solid solution is proved by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) and the intimate contact between TiO 2 nanofibers and ZnS–In 2 S 3 solid solution favors fast transfer of photogenerated electrons. The trinary TiO 2 @ZnS–In 2 S 3 heterostructures exhibit high adsorption capacity and visible light photocatalytic activity for the degradation of rhodamine B dye (RhB), remarkably superior to pure TiO 2 nanofibers or binary structures (ZnS/TiO 2 nanofibers, In 2 S 3 /TiO 2 nanofibers and ZnS–In 2 S 3 solid solution). Under visible light irradiation the RhB photocatalytic degradation rate over TiO 2 @ZnS–In 2 S 3 heterostructures is about 16.7, 12.5, 6.3, 5.9, and 2.2 times that over pure TiO 2 nanofibers, ZnS nanoparticles, In 2 S 3 /TiO 2 nanofibers, ZnS/TiO 2 nanofibers, and ZnS-In 2 S 3 solid solution, respectively. Furthermore, the TiO 2 @ZnS–In 2 S 3 heterostructures show highly stable recycling performance

Synthesis of La2O3 doped Zn2SnO4 hollow fibers by electrospinning method and application in detecting of acetone

Science.gov (United States)

Yang, H. M.; Ma, S. Y.; Yang, G. J.; Chen, Q.; Zeng, Q. Z.; Ge, Q.; Ma, L.; Tie, Y.

2017-12-01

Hollow porous pure and La2O3 doped Zn2SnO4 fibers were synthesized via single capillary electrospinning technology and used for obtaining of gas sensors. The as-prepared samples were characterized by microscopy, Brunauer-Emmett-Teller, X-ray photoelectron spectroscopy and UV-vis absorption spectra. The newly obtained gas sensors were investigated for acetone detection. Compared with pure Zn2SnO4 hollow fibers, the La2O3 doped Zn2SnO4 hollow fibers not only exhibited perfect sensing performance toward acetone with excellent selectivity, high response and fast response/recovery capability (7 s for adsorption and 9 s for desorption), but also the operating temperature was reduced from 240 °C to 200 °C. These results demonstrated that the special hollow porous La doped Zn2SnO4 fibers structures were used as the sensing material for fabricating high performance acetone sensors. The acetone sensing mechanism of La2O3 doped Zn2SnO4 hollow fibers was discussed too.

Synthesis and properties of Li2SnO3/polyaniline nanocomposites as negative electrode material for lithium-ion batteries

International Nuclear Information System (INIS)

Wang Qiufen; Huang Ying; Miao Juan; Zhao Yang; Wang Yan

2012-01-01

Highlights: ► Li 2 SnO 3 /polyaniline nanocomposite (40–50 nm) was synthesized by micro emulsion polymerization. ► Li 2 SnO 3 /PANI exhibits lower initial irreversible capacities than Li 2 SnO 3 . ► Its capacity retains 569.2 mAh g −1 after 50 cycles. - Abstract: The nanocomposites Li 2 SnO 3 /polyaniline (Li 2 SnO 3 /PANI) have been synthesized by a micro emulsion polymerization method. The structure, morphology and electrochemical properties of the as-prepared materials are characterized by XRD, FTIR, Raman, XPS, TGA, TEM and electrochemical measurements. Results show that Li 2 SnO 3 /PANI nanocomposites are composed of uniform and blocky nano-sized particles (40–50 nm) with clear lattice fringes. Electrochemical measurement suggests that Li 2 SnO 3 /PANI exhibits better cycling properties and lower initial irreversible capacities than Li 2 SnO 3 as negative electrodes materials for lithium-ion batteries. At a current density of 60 mA g −1 in the voltage about 0.05–2.0 V, the initial irreversible capacity of Li 2 SnO 3 /PANI is 563 mAh g −1 while it is 687.5 mAh g −1 to Li 2 SnO 3 . The capacity retained of Li 2 SnO 3 /PANI (569.2 mAh g −1 ) is higher than that of Li 2 SnO 3 (510.2 mAh g −1 ) after 50 cycles. The PANI in the Li 2 SnO 3 /PANI nanocomposites can buffer the released stress caused by the drastic volume variation during the alloying/de-alloying process of Li–Sn.

Nanocrystalline SnO2 by liquid pyrolysis

Directory of Open Access Journals (Sweden)

Morante, J. R.

2000-08-01

Full Text Available Liquid pyrolysis is presented as a new production method of SnO2 nanocrystalline powders suitable for gas sensor devices. The method is based on a pyrolytic reaction of high tensioned stressed drops of an organic solution of SnCl4•5(H2O. The main advantages of the method are its capability to produce SnO2 nanopowders with high stability, its accurate control over the grain size and other structural characteristics, its high level of repeatability and its low industrialization implementation cost. The characterization of samples of SnO2 nanoparticles obtained by liquid pyrolysis in the range between 200ºC and 900ºC processing temperature is carried out by X-ray diffraction, transmission electron microscopy, Raman and X-ray photoelectron spectroscopy. Results are analyzed and discussed so as to validate the advantages of the liquid pyrolysis method.La pirólisis líquida se presenta como un nuevo método para producir SnO2 nanocristalino en polvo ideal para sensores de gas. El método se basa en una reacción pirolítica de gotas altamente tensionadas procedentes de una solución orgánica de SnCl4•5(H2O. Las principales ventajas del método son la capacidad para producir nanopartículas de SnO2 con una gran estabilidad, el preciso control sobre el tamaño de grano y sobre otras características estructurales, el alto nivel de repetibilidad y el bajo coste en su implementación industrial.La caracterización de las muestras de las nanopartículas de SnO2 obtenidas por pirólisis líquida en un rango de temperatura de procesado que va de 200ºC a 900ºC se ha realizado mediante difracción de rayos X, microscopía electrónica de transmisión, espectroscopía Raman y espectroscopía fotoelectrónica de rayos X. Los resultados se han analizado y discutido. Éstos validan las ventajas del método de la pirólisis líquida.

Thermoelectric Properties of SnO2 Ceramics Doped with Sb and Zn

DEFF Research Database (Denmark)

Yanagiya, S.; Van Nong, Ngo; Xu, Jianxiao Jackie

2011-01-01

Polycrystalline SnO2-based samples (Sn0.97−x Sb0.03Zn x O2, x = 0, 0.01, 0.03) were prepared by solid-state reactions. The thermoelectric properties of SnO2 doped with Sb and Zn were investigated from 300 K to 1100 K. X-ray diffraction (XRD) analysis revealed all XRD peaks of all the samples...

Study of solid state interactions in the systems ZnFe2O4 - CaO, ZnFe2O4 - MgO and zinc cake with CaO and MgO

Directory of Open Access Journals (Sweden)

Peltekov A.B.

2013-01-01

Full Text Available The solid state interactions of CaO and MgO with synthetic and industrial ZnFe2O4 (in zinc cake have been studied using chemical, XRD analysis and Mössbauer spectroscopy. The exchange reactions in the systems ZnFe2O4 - CaO and ZnFe2O4 - MgO have been investigated in the range of 850-1200ºC and duration up to 180 min. It has been established that Ca2+ and Mg2+ ions exchange Zn2+ in ferrite partially and the solubility of zinc in a 7% sulfuric acid solution increases. The possibilities for utilization of the obtained results in zinc hydrometallurgy have been discussed.

Removal of UO{sup 2+}{sub 2} from aqueous solution using halloysite nanotube-Fe{sub 3}O{sub 4} composite

Energy Technology Data Exchange (ETDEWEB)

He, Wenfang; Chen, Yuantao; Zhang, Wei; Hu, Chunlian; Wang, Jian; Wang, Pingping [Qinghai Normal University, Xining (China)

2016-01-15

Halloysite nanotubes (HNTs) were modified with Fe{sub 3}O{sub 4} to form novel magnetic HNTs-Fe{sub 3}O{sub 4} composites, and the composites were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), Fourier transform infrared spectroscopy (FT-IR) and vibrating sample magnetometer (VSM). The as-obtained results indicated that Fe{sub 3}O{sub 4} nanoparticles were successfully installed on the surface of HNTs. The adsorption of UO{sup 2+}{sub 2} on HNTs-Fe{sub 3}O{sub 4} was investigated as a function of solid content, contact time, pH, ionic strength and temperature by batch experiments. The consequences revealed that the adsorption of UO{sup 2+}{sub 2} onto HNTs-Fe{sub 3}O{sub 4} was strongly dependent on pH and ionic strength. Equilibrium data fitted well with the Langmuir isotherm. The experimental results demonstrated that the adsorbents with HNTs-Fe{sub 3}O{sub 4} had the largest adsorption capacity of 88.32mg/g for UO{sup 2+}{sub 2}.

Electrical conduction of glasses in the system Fe2O3-Sb2O3-TeO2; Fe2O3-Sb2O3-TeO2 kei garasu no denki dendo

Energy Technology Data Exchange (ETDEWEB)

Qiu, Honghua; Mori, H; Sakata, H; Hirayama, T [Tokai Univ., Tokyo (Japan). Faculty of Engineering

1995-01-01

In this study, taking into consideration that TeO2 is a component of the glass network and Sb2O3 shows the redox effect in the glasses reducing its possibility of transformation of Sb{sup 3+} to Sb{sup 5+} as well as glass basicity, highly conductive tellurite based glasses have been prepared by the press-quenching method selecting the Fe2O3-Sb2O3-TeO2 system, and the electroconductive mechanism of the glasses has been examined by measuring its D.C. conductivity {sigma}. Part of the obtained information is as follows; the glass formation range of the Fe2O3-Sb2O3-TeO2 system has been 0 {le} Fe2O3 {le} 15mol%, 0 {le} Sb2O3 {le} 18mol% and 78 {le} TeO2 {le} 100mol% and about 15mol% of the additional amount of Fe2O3 has been the limit of glass formation. As the amount of Fe2O3 has increased, C{sub Fe} has also increased and with this, the linear electroconductivity of the glasses has increased from 1.86 {times} 10{sup -7}S{center_dot}cm{sup -1} to 1.62 {times} 10{sup -6}S{center_dot}cm{sup -1} and the glasses have been confirmed as the n-type semiconductor. The factor determining {sigma} of the glasses has been C{sub Fe} which has increased as the amount of Fe2O3 has increased. 34 refs., 8 figs., 2 tabs.

Ultrathin SnO2 nanorods: template- and surfactant-free solution phase synthesis, growth mechanism, optical, gas-sensing, and surface adsorption properties.

Science.gov (United States)

Xi, Guangcheng; Ye, Jinhua

2010-03-01

A novel template- and surfactant-free low temperature solution-phase method has been successfully developed for the controlled synthesis of ultrathin SnO(2) single-crystalline nanorods for the first time. The ultrathin SnO(2) single-crystalline nanorods are 2.0 +/- 0.5 nm in diameter, which is smaller than its exciton Bohr radius. The ultrathin SnO(2) nanorods show a high specific area (191.5 m(2) g(-1)). Such a thin SnO(2) single-crystalline nanorod is new in the family of SnO(2) nanostrucures and presents a strong quantum confinement effect. Its formation depends on the reaction temperature as well as on the concentration of the urea solution. A nonclassical crystallization process, Ostwald ripening process followed by an oriented attachment mechanism, is proposed based on the detailed observations from a time-dependent crystal evolution process. Importantly, such structured SnO(2) has shown a strong structure-induced enhancement of gas-sensing properties and has exhibited greatly enhanced gas-sensing property for the detection of ethanol than that of other structured SnO(2), such as the powders of nanobelts and microrods. Moreover, these ultrathin SnO(2) nanorods exhibit excellent ability to remove organic pollutant in wastewater by enormous surface adsorption. These properties are mainly attributed to its higher surface-to-volume ratio and ultrathin diameter. This work provides a novel low temperature, green, and inexpensive pathway to the synthesis of ultrathin nanorods, offering a new material form for sensors, solar cells, catalysts, water treatments, and other applications.

The influence of Cd-dopant on the properties of α-FeOOH and α-Fe2O3 particles precipitated in highly alkaline media

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar

2007-01-01

The effects of Cd-dopant on the phenomenology of the precipitation of α-(Fe, Cd)OOH and α-(Fe, Cd) 2 O 3 particles, the formation of solid solutions, particle size and their geometrical shapes were investigated using Moessbauer and Fourier transform infrared (FT-IR) spectroscopies, field emission scanning electron microscopy (FE SEM) and energy dispersive X-ray analysis (EDS). The formation of merely α-(Fe, Cd)OOH solid solutions was measured up to r = 0.0196, where r = [Cd]/([Cd] + [Fe]). The formation of two types of solid solutions, α-(Fe, Cd)OOH and α-(Fe, Cd) 2 O 3 was found at r between 0.0291 and 0.0698, whereas the formation of an α-(Fe, Cd) 2 O 3 solid solution alone was obtained at r = 0.0909. The incorporation of Cd-substitutions into α-FeOOH and α-Fe 2 O 3 structures decreased the hf > values of the corresponding hyperfine magnetic field. The IR band at 639 cm -1 , recorded for α-FeOOH, was found to be sensitive to Cd-substitutions. With an increased r value a gradual elongation of α-(Fe, Cd)OOH particles along the c-axis was observed, with the maximum elongation (∼600-700 nm) obtained at r = 0.0476. At the same time, particle width (b-axis direction) and thickness (a-axis direction) showed a gradual decrease. With a further increase in the r value the length of α-(Fe, Cd)OOH particles rapidly decreased. α-(Fe, Cd) 2 O 3 particles ∼100-200 nm in size were obtained at r = 0.0909

Microemulsion mediated synthesis of triangular shape SnO2 nanoparticles: Luminescence application

International Nuclear Information System (INIS)

Luwang, Meitram Niraj

2014-01-01

The triangular prism shapes of SnO 2 ·xH 2 O nanoparticles are prepared using microemulsion route. The effect of variation of water pool value on the formation of SnO 2 nanoparticles was studied. There is the quantum size effect in absorption study of SnO 2 nanoparticles. With the increase of the water pool value, there is a decrease in the band edge absorption energy suggesting the weak quantum confinement effect (QCE) in SnO 2 nanoparticles. Quenching effect increases with increase of water to surfactant ratio in luminescence. There is no significant effect in lifetime values for SnO 2 nanoparticles in both microemulsion and powder form. SnO 2 nanoparticles show green emission due to oxygen vacancy. SnO 2 nanoparticles when doped with Eu 3+ ions give the enhanced luminescence of Eu 3+ due to the surface mediated energy transfer from SnO 2 to Eu 3+ ion.

Synthesis and structural characteristics of the spinel-type solid solutions in the Mn-V-Fe-O system

International Nuclear Information System (INIS)

Ponomaryov, V.I.; Dubrovina, I.N.; Zakharov, R.G.

1976-01-01

The part of the spinel region bounded by the compounds Mn 3 O 4 , Mn 2 VO 4 , Fe 2 VO 4 , and Fe 3 O 4 in the four-component system Mn-V-Fe-O was studied. The compounds were synthesized by ceramic technology. Samples were heated in a CO 2 atmosphere free of oxygen at 1100 0 C for 25-50 hr. It was found that the average composition of the spinel compound in the system had the formula Mnsub(1.00)Fesub(1.33)Vsub(0.67)O 4 . X-ray and neutron radiogrphic analyses were made. Crystallo-chemical formulas of the solid solutions considered are tabulated. The magnetic moments of saturation, calculated by the Neel model, are shown, and their experimental values are presented. The crystallo-chemical formulas of the spinel solid solutions in the Mn-V-Fe-O system are of interest in interpreting the concentration dependence of the physico-chemical properties of solid solutions of oxides based on metals with varying valence

Synthesis and properties of Li2SnO3/polyaniline nanocomposites as negative electrode material for lithium-ion batteries

Science.gov (United States)

Wang, Qiufen; Huang, Ying; Miao, Juan; Zhao, Yang; Wang, Yan

2012-10-01

The nanocomposites Li2SnO3/polyaniline (Li2SnO3/PANI) have been synthesized by a micro emulsion polymerization method. The structure, morphology and electrochemical properties of the as-prepared materials are characterized by XRD, FTIR, Raman, XPS, TGA, TEM and electrochemical measurements. Results show that Li2SnO3/PANI nanocomposites are composed of uniform and blocky nano-sized particles (40-50 nm) with clear lattice fringes. Electrochemical measurement suggests that Li2SnO3/PANI exhibits better cycling properties and lower initial irreversible capacities than Li2SnO3 as negative electrodes materials for lithium-ion batteries. At a current density of 60 mA g-1 in the voltage about 0.05-2.0 V, the initial irreversible capacity of Li2SnO3/PANI is 563 mAh g-1 while it is 687.5 mAh g-1 to Li2SnO3. The capacity retained of Li2SnO3/PANI (569.2 mAh g-1) is higher than that of Li2SnO3 (510.2 mAh g-1) after 50 cycles. The PANI in the Li2SnO3/PANI nanocomposites can buffer the released stress caused by the drastic volume variation during the alloying/de-alloying process of Li-Sn.

Ternary composite of TiO2 nanotubes/Ti plates modified by g-C3N4 and SnO2 with enhanced photocatalytic activity for enhancing antibacterial and photocatalytic activity.

Science.gov (United States)

Faraji, Masoud; Mohaghegh, Neda; Abedini, Amir

2018-01-01

A series of g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plates were fabricated via simple dipping of TiO 2 nanotubes/Ti in a solution containing SnCl 2 and g-C 3 N 4 nanosheets and finally annealing of the plates. Synthesized plates were characterized by various techniques. The SEM analysis revealed that the g-C 3 N 4 -SnO 2 nanosheets with high physical stability have been successfully deposited onto the surface of TiO 2 nanotubes/Ti plate. Photocatalytic activity was investigated using two probe chemical reactions: oxidative decomposition of acetic acid and oxidation of 2-propanol under irradiation. Antibacterial activities for Escherichia coli (E. coli) bacteria were also investigated in dark and under UV/Vis illuminations. Detailed characterization and results of photocatalytic and antibacterial activity tests revealed that semiconductor coupling significantly affected the photocatalyst properties synthesized and hence their photocatalytic and antibacterial activities. Modification of TiO 2 nanotubes/Ti plates with g-C 3 N 4 -SnO 2 deposits resulted in enhanced photocatalytic activities in both chemical and microbial systems. The g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plate exhibited the highest photocatalytic and antibacterial activity, probably due to the heterojunction between g-C 3 N 4 -SnO 2 and TiO 2 nanotubes/Ti in the ternary composite plate and thus lower electron/hole recombination rate. Based on the obtained results, a photocatalytic and an antibacterial mechanism for the degradation of E. coli bacteria and chemical pollutants over g-C 3 N 4 -SnO 2 /TiO 2 nanotubes/Ti plate were proposed and discussed. Copyright © 2017 Elsevier B.V. All rights reserved.

Phase formation in the Li2MoO4–Rb2MoO4–Fe2(MoO4)3 system and crystal structure of a novel triple molybdate LiRb2Fe(MoO4)3

International Nuclear Information System (INIS)

Khal'baeva, Klara M.; Solodovnikov, Sergey F.; Khaikina, Elena G.; Kadyrova, Yuliya M.; Solodovnikova, Zoya A.; Basovich, Olga M.

2013-01-01

X-ray investigation of solid state interaction of the components in the Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system was carried out, and a subsolidus phase diagram of the said system was constructed. The subsystem Rb 2 MoO 4 –LiRbMoO 4 –RbFe(MoO 4 ) 2 was shown to be non-quasiternary. Formation of a novel triple molybdate LiRb 2 Fe(MoO 4 ) 3 was established, conditions of solid state synthesis and crystallization of the compound were found. Its crystal structure (orthorhombic, space group Pnma, Z=4, a=24.3956(6), b=5.8306(1), c=8.4368(2) Å) represents a new structure type and includes infinite two-row ribbons ([Fe(MoO 4 ) 3 ] 3− ) ∞ parallel to the b axis and composed of FeO 6 octahedra, terminal Mo(3)O 4 tetrahedra, and bridge Mo(1)O 4 and Mo(2)O 4 tetrahedra connecting two or three FeO 6 octahedra. The ribbons are connected to form 3D framework via corner-sharing LiO 4 tetrahedra. Rubidium cations are 11- and 13-coordinated and located in cavities of this heterogeneous polyhedral framework. - Graphical abstract: Exploring the Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system showed its partial non-quasiternarity and revealed a new compound LiRb 2 Fe(MoO 4 ) 3 which was structurally studied. - Highlights: • The Li 2 MoO 4 –Rb 2 MoO 4 –Fe 2 (MoO 4 ) 3 system study revealed a new compound LiRb 2 Fe(MoO 4 ) 3 . • Its structure of a new type includes ribbons of FeO 6 octahedra and MoO 4 tetrahedra. • The ribbons are connected into a 3D framework via corner-sharing LiO 4 tetrahedra

Tetragonal-cubic phase boundary in nanocrystalline ZrO2-Y2O3 solid solutions synthesized by gel-combustion

International Nuclear Information System (INIS)

Fabregas, Ismael O.; Craievich, Aldo F.; Fantini, Marcia C.A.; Millen, Ricardo P.; Temperini, Marcia L.A.; Lamas, Diego G.

2011-01-01

Research highlights: → Gel-combustion synthesis yields compositionally homogeneous, single-phased ZrO 2 -Y 2 O 3 nanopowders, that exhibit the presence at room temperature of three different phases depending on Y 2 O 3 content, namely two tetragonal forms (t' and t'') and the cubic phase. → Phase identification can be achieved by synchrotron XPD (SXPD) and Raman spectroscopy since the tetragonal forms and the cubic phase can be distinguished by these techniques. → The crystallographic features of ZrO 2 -Y 2 O 3 nanopowders were determined by SXPD. They are similar to those reported by Yashima and coworkers for compositionally homogeneous materials containing larger (micro)crystals. However, the lattice parameters are slightly different and the axial ratios c/a of our t' samples are smaller than those reported by these authors. → Compositional t'/t'' and t''/cubic phase boundaries are located at (9 ± 1) and (10.5 ± 0.5) mol% Y 2 O 3 , respectively. → For the whole series of nanocrystalline ZrO 2 -Y 2 O 3 solid solutions studied in the present work, no evidences of the presence of a mixture of phases - as reported by Yashima and coworkers for microcrystalline solid solutions - were detected. - Abstract: By means of synchrotron X-ray powder diffraction (SXPD) and Raman spectroscopy, we have detected, in a series of nanocrystalline and compositionally homogeneous ZrO 2 -Y 2 O 3 solid solutions, the presence at room temperature of three different phases depending on Y 2 O 3 content, namely two tetragonal forms and the cubic phase. The studied materials, with average crystallite sizes within the range 7-10 nm, were synthesized by a nitrate-citrate gel-combustion process. The crystal structure of these phases was also investigated by SXPD. The results presented here indicate that the studied nanocrystalline ZrO 2 -Y 2 O 3 solid solutions exhibit the same phases reported in the literature for compositionally homogeneous materials containing larger (micro

Influence of ruthenium ions on the precipitation of α-FeOOH, α-Fe2O3 and Fe3O4 in highly alkaline media

International Nuclear Information System (INIS)

Krehula, Stjepko; Music, Svetozar

2006-01-01

The influence of ruthenium ions on the precipitation of goethite (α-FeOOH), α-Fe 2 O 3 and Fe 3 O 4 in highly alkaline media was investigated by 57 Fe Moessbauer and FT-IR spectroscopies, thermal field emission scanning electron microscope (FE SEM) and EDS. The presence of Ru-dopant strongly affected the precipitation of α-FeOOH at highly alkaline pH, i.e. the formation of α-Fe 2 O 3 was also noticed. A decrease of hyperfine magnetic field (HMF) at RT from 35.1 T (undoped α-FeOOH) to 31.3 T for sample with [Ru]/([Ru] + [Fe]) = 0.0196 was assigned to the incorporation of ruthenium ions into the α-FeOOH structure. Moessbauer spectroscopy showed the formation of stoichiometric Fe 3 O 4 for [Ru]/([Ru] + [Fe]) = 0.0291-0.0909. α-Fe 2 O 3 and Fe 3 O 4 did not show a tendency to the formation of solid solutions with ruthenium ions. FE SEM observations of the samples showed that reference α-FeOOH sample contained acicular particles of good uniformity, which increased the length up to ∼5 times with increase of concentration of ruthenium ions. On the other hand, large octahedral Fe 3 O 4 crystals (particles) were associated with small particles of ruthenium (hydrous) oxide with a size in the range ∼100 nm or less. A possible catalytic action of ruthenium that created reduction conditions for Fe 3+ ions and formation of Fe 2+ ions for precipitation of Fe 3 O 4 was discussed

alpha-Fe2O3 versus beta-Fe2O3: Controlling the Phase of the Transformation Product of epsilon-Fe2O3 in the Fe2O3/SiO2 System

Czech Academy of Sciences Publication Activity Database

Brázda, Petr; Kohout, J.; Bezdička, Petr; Kmjec, T.

2014-01-01

Roč. 14, č. 3 (2014), s. 1039-1046 ISSN 1528-7483 R&D Projects: GA ČR GAP204/10/0035 Institutional support: RVO:61388980 Keywords : CHEMICAL-VAPOR-DEPOSITION * OXIDE THIN-FILMS * X-RAY * GAMMA-FE2O3 NANOPARTICLES * THERMAL-DECOMPOSITION Subject RIV: CA - Inorganic Chemistry Impact factor: 4.891, year: 2014

Fe-Al2O3 nanocomposites prepared by high-energy ball milling

DEFF Research Database (Denmark)

Linderoth, Søren; Pedersen, M.S.

1994-01-01

Nanocomposites of alpha-Fe and alpha-Al2O3, prepared by high-energy ball milling, exhibit coercivities which are enhanced by about two orders of magnitude with respect to the bulk value. The degree of enhancement depends on the volume fraction (x(upsilon)) of Fe, with a maximum for x(upsilon) alm......Nanocomposites of alpha-Fe and alpha-Al2O3, prepared by high-energy ball milling, exhibit coercivities which are enhanced by about two orders of magnitude with respect to the bulk value. The degree of enhancement depends on the volume fraction (x(upsilon)) of Fe, with a maximum for x...

A new model and gas sensitivity of non-equilibrium xSnO2-(1-x)alpha-Fe2O3 nanopowders prepared by mechanical alloying

DEFF Research Database (Denmark)

Zhu, W.; Tan, O.K.; Jiang, Jianzhong

1998-01-01

)alpha-Fe2O3 materials. This model can explain non only the lattice expansion of the milled samples, but also takes into account the charge balance by adding oxygen dangling bonds at the particle surfaces, which can be visualized in the nano-sized powders. The thich film gas sensors made by such mechanically......Nano-sized xSnO2-(1-x)alpha-Fe2O3 materials have been prepared using the high energy ball milling technique and their structural and gas sensing properties have been characterized. Based on experimental results, we propose a new structure model, xxx, forthese non-equilibrium, nano-sized xSnO2-(1-x...... alloyed materials have high ethanol gas sensitivity values of 289 in air and 1016 in nitrogen at 1000 p.p.m. and very good gas selectivity to ethanol over CO and H2 gases. It is believed that the high ethanol gas sensitivity of these materials is related to the enormous defects such as O- and O2- dangling...

Core-Shell Nano structure of a-Fe2O3/Fe3O4: Synthesis and Photo catalysis for Methyl Orange

International Nuclear Information System (INIS)

Tian, Y.; Wu, D.; Yu, B.; Jia, X.; Zhan, S.

2011-01-01

Fe 3 O 4 nanoparticle was synthesized in the solution involving water and ethanol. Then, a-Fe 2 O 3 shell was produced in situ on the surface of the Fe 3 O 4 nanoparticle by surface oxidation in molten salts, forming α-Fe 2 O 3 /Fe 3 O 4 core-shell nano structure. It was showed that the magnetic properties transformed from ferromagnetism to superparamagnetism after the primary Fe 3 O 4 nanoparticles were oxidized. Furthermore, the obtained a-Fe 2 O 3 /Fe 3 O 4 core-shell nanoparticles were used to photo catalyse solution of methyl orange, and the results revealed that a-Fe 2 O 3 /Fe 3 O 4 nanoparticles were more efficient than the self-prepared α-Fe 2 O 3 nanoparticles. At the same time, the photo catalyzer was recyclable by applying an appropriate magnetic field.

Stabilization of the high coercivity ε-Fe2O3 phase in the CeO2–Fe2O3/SiO2 nanocomposites

International Nuclear Information System (INIS)

Mantlikova, A.; Poltierova Vejpravova, J.; Bittova, B.; Burianova, S.; Niznansky, D.; Ardu, A.; Cannas, C.

2012-01-01

We have investigated the processes leading to the formation of the Fe 2 O 3 and CeO 2 nanoparticles in the SiO 2 matrix in order to stabilize the ε-Fe 2 O 3 as the major phase. The samples with two different concentrations of the Fe were prepared by sol–gel method, subsequently annealed at different temperatures up to 1100 °C, and characterized by the Mössbauer spectroscopy, Transmission Electron Microscopy (TEM), Powder X-ray Diffraction (PXRD), Energy Dispersive X-ray analysis (EDX) and magnetic measurements. The evolution of the different Fe 2 O 3 phases under various conditions of preparation was investigated, starting with the preferential appearance of the γ-Fe 2 O 3 phase for the sample with low Fe concentration and low annealing temperature and stabilization of the major ε-Fe 2 O 3 phase for high Fe concentration and high annealing temperature, coexisting with the most stable α-Fe 2 O 3 phase. A continuous increase of the particle size of the CeO 2 nanocrystals with increasing annealing temperature was also observed. - Graphical abstract: The graphical abstract displays the most important results of our work. The significant change of the phase composition due to the variation of preparation conditions is demonstrated. As a result, significant change of the magnetic properties from superparamagnetic γ-Fe 2 O 3 phase with negligible coercivity to the high coercivity ε-Fe 2 O 3 phase has been observed. Highlights: ► Research of the stabilization of the high coercivity ε-Fe 2 O 3 in CeO 2 –Fe 2 O 3 /SiO 2 . ► Samples with two different concentrations of Fe and three annealing temperatures. ► Phase transition γ→ε→(β)→α with increasing annealing temperature and particle size. ► Elimination of the superparamagnetic phases in samples with higher content of Fe. ► Best conditions for high coercivity ε-Fe 2 O 3 —higher Fe content and T A =1100°C.

Composition dependent room temperature structure, electric and magnetic properties in magnetoelectric Pb(Fe{sub 1/2}Nb{sub 1/2})O{sub 3}−Pb(Fe{sub 2/3}W{sub 1/3})O{sub 3} solid-solutions

Energy Technology Data Exchange (ETDEWEB)

Matteppanavar, Shidaling [Department of Physics, Jnanabharathi Campus, Bangalore University, Bangalore, 560056 (India); Rayaprol, Sudhindra [UGC-DAE-Consortium for Scientific Research, Mumbai Centre, B A R C Campus, Mumbai, 400085 (India); Angadi, Basavaraj, E-mail: brangadi@gmail.com [Department of Physics, Jnanabharathi Campus, Bangalore University, Bangalore, 560056 (India); Sahoo, Balaram [Materials Research Centre, Indian Institute of Science, Bangalore, 560012 (India)

2016-08-25

We report on the studies of room temperature (RT) crystal structure, electric and magnetic properties of (1−x) Pb(Fe{sub 1/2}Nb{sub 1/2})O{sub 3} – x Pb(Fe{sub 2/3}W{sub 1/3})O{sub 3} (PFN{sub 1−x} – PFW{sub x}) (x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) solid solutions through the measurements of X-ray diffraction, FTIR, scanning electron microscopy (SEM), Neutron diffraction, Raman, Magnetic, Mössbauer and ferroelectric measurements. FTIR spectra showed two main perovskite related transmission bands. The SEM analysis shows an average grain size of 2 μm for all the solid solutions. Rietveld refinement was performed on RT X-ray diffraction (XRD) and neutron diffraction (ND), which reveals, the monoclinic phase for x = 0.0 with space group Cm and Cubic phase for x = 1.0 with space group Pm-3m. In other words, increasing x, the samples exhibit a gradual phase transition from monoclinic to cubic. In addition, the Raman spectroscopy corroborates the change in structural symmetry from monoclinic (Cm) to cubic (Pm-3m) on varying x. The coexistence of both monoclinic and cubic symmetries was observed between x = 0.2–0.8. Magnetic measurements shows that, the magnetic phase transition from paramagnetic to antiferromagnetic (AFM) was observed at or above RT for x = 0.6 and above. The magnetic structure was refined using the propagation vector k = (½, ½, ½) and structure was found to be G-type antiferromagnetic. Magnetic properties (M-H loops) shows, a weak ferromagnetic behaviour with antiferromagnetic ordering at RT. At RT, x = 0.0–0.6 the samples exhibits disordered paramagnetic property but weakly coupled with antiferromagnetic domains. But, x = 0.8 and 1.0 samples show antiferromagnetic and they are weakly coupled with paramagnetic domains. The temperature dependent magnetization (M(T)) confirms, the augmentation of Néel temperature (T{sub N}) from 155 K to 350 K on increasing x. Mössbauer spectroscopy confirms superparamagnetic nature with the presence of

Rapid synthesis and optical properties of hematite ({alpha}-Fe{sub 2}O{sub 3}) nanostructures using a simple thermal decomposition method

Energy Technology Data Exchange (ETDEWEB)

Al-Gaashani, R., E-mail: Rashad_jashani@yahoo.com [School of Applied Physics, Faculty Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Department of Physics, Thamar University, Dhamar, Republic of Yemen (Yemen); Radiman, S. [School of Applied Physics, Faculty Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Tabet, N. [Department of Physics and Center of Research Excellence in Renewable Energy, King Fahd University of Petroleum and Minerals, Dhahran (Saudi Arabia); Daud, A.R. [School of Applied Physics, Faculty Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

2013-02-15

Highlights: Black-Right-Pointing-Pointer A novel method for the synthesis of hematite nanopowder is reported. Black-Right-Pointing-Pointer The morphology of {alpha}-Fe{sub 2}O{sub 3} changed with altering the preparation temperature. Black-Right-Pointing-Pointer The coral like nano {alpha}-Fe{sub 2}O{sub 3} prepared at 500 and 600 Degree-Sign C showed novel optical behavior. Black-Right-Pointing-Pointer The coral like nano {alpha}-Fe{sub 2}O{sub 3} could be used to enhance efficiency of the solar cells. - Abstract: Hematite nanostructures were prepared by a simple technique using the thermal decomposition of iron (III) nitrate 9-hydrate at different temperatures under air atmosphere. Observations using field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) showed that the morphology of the nanostructures changed as the temperature was varied while their size increased with increasing preparation time. Samples prepared at 300, 400, and 500 Degree-Sign C were made of particles with a quantum dots (QDs) size. X-ray photoelectron spectroscopy (XPS), energy dispersive spectroscopy (EDS) and X-ray diffraction (XRD) confirmed that the as-synthesized powders are pure {alpha}-Fe{sub 2}O{sub 3}. The optical energy gap of the samples varied from 3.2 eV to 2.7 eV as the preparation temperature increased from 300 Degree-Sign C to 600 Degree-Sign C.

SnO2 thin film synthesis for organic vapors sensing at ambient temperature

Directory of Open Access Journals (Sweden)

N.H. Touidjen

2016-12-01

Full Text Available The present work is a study of tin dioxide (SnO2 based thin sensitive layer dedicated to organic vapors detection at ambient temperature. SnO2 thin film was deposited by chemical spray pyrolysis technique. The glass substrate temperature was kept to 400 °C, using a starting solution of 0.1 M tin (II dichloride dihydrate (SnCl2, 2H2O. Films structural and morphological properties were characterized using X-ray diffraction (XRD, scanning electron microscopy (SEM and atomic force microscope (AFM respectively. Films optical characteristics were studied using UV-VIS spectrophotometer. XRD revealed the presence of pure SnO2 polycrystalline thin film with a tetragonal rutile structure. The SEM and AFM observations confirmed the granular morphology with presence of pores in the film surface. The prepared film was tested in various organic vapors (ethanol, methanol and acetone at ambient operating temperature (25 °C ± 2 °C. The obtained results suggested that SnO2 is more sensitive to ethanol vapor with a maximum sensitivity of 35% higher than to methanol and acetone vapors (1% and 3%. The realized SnO2 based sensor demonstrated fast response and recovery times as revealed by the values of 2 s to 3 s towards 47 ppm of ethanol vapor. Keywords: SnO2 thin film, Sensitivity, XRD, SEM, AFM, UV–visible

Effect of Cr2O3 on the microstructure and non-ohmic properties of (Co, Sb)-doped SnO2 varistors

International Nuclear Information System (INIS)

Aguilar M, J. A.; Pech C, M. I.; Hernandez, M. B.; Rodriguez, E.; Garcia O, L.; Glot, A. B.

2013-01-01

The effect of Cr 2 O 3 addition on the physical characteristics, microstructure, and current-voltage properties of (Co-Sb)-doped SnO 2 varistors was investigated. SnO 2 -Co 3 O 4 -Sb 2 O 5 ceramics with additions of 0.0, 0.03, 0.05 and 0.07 mol % Cr 2 O 3 were sintered at 1350 C under ambient atmosphere and characterized micro structurally and electrically. The characterization by X-ray diffraction and scanning electron microscopy show that the microstructure remains as a single phase material with multimodal size distribution of SnO 2 grains. The greatest effect of Cr 2 O 3 additions is manifested in the electric breakdown field. Additions of high levels (0.07 and 0.05 %) of this oxide promote and increase of approximately 55% in this parameter compared to the Cr 2 O 3 -free sample. Another physical property is affected: the measured density values decreases as the Cr 2 O 3 content increases. A change in the nonlinearity coefficient value is produced only at the highest Cr 2 O 3 content while at intermediate levels there is not change at all. Consequently, when seeking high nonlinearity coefficients, intermediate levels of Cr 2 O 3 are not recommended. (Author)

Role of Cu in engineering the optical properties of SnO2 nanostructures: Structural, morphological and spectroscopic studies

Science.gov (United States)

Kumar, Virender; Singh, Kulwinder; Jain, Megha; Manju; Kumar, Akshay; Sharma, Jeewan; Vij, Ankush; Thakur, Anup

2018-06-01

We have carried out a systematic study to investigate the effect of Cu doping on the optical properties of SnO2 nanostructures synthesized by chemical route. Synthesized nanostructures were characterized using X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), High resolution transmission electron microscopy (HR-TEM), Energy dispersive X-ray spectroscopy, Raman spectroscopy, Fourier transform infrared (FTIR) spectroscopy, UV-visible and Photoluminescence (PL) spectroscopy. The Rietveld refinement analysis of XRD patterns of Cu-doped SnO2 samples confirmed the formation of single phase tetragonal rutile structure, however some localized distortion was observed for 5 mol% Cu-doped SnO2. Crystallite size was found to decrease with increase in dopant concentration. FE-SEM images indicated change in morphology of samples with doping. HR-TEM images revealed that synthesized nanostructures were nearly spherical and average crystallite size was in the range 12-21 nm. Structural defects, crystallinity and size effects on doping were investigated by Raman spectroscopy and results were complemented by FTIR spectroscopy. Optical band gap of samples was estimated from reflectance spectra. We have shown that band gap of SnO2 can be engineered from 3.62 to 3.82 eV by Cu doping. PL emission intensity increased as the doping concentration increased, which can be attributed to the development of defect states in the forbidden transition region of band gap of SnO2 with doping. We have also proposed a band model owing to defect states in SnO2 to explain the observed PL in Cu doped SnO2 nanostructures.

Response speed of SnO2-based H2S gas sensors with CuO nanoparticles

International Nuclear Information System (INIS)

Chowdhuri, Arijit; Gupta, Vinay; Sreenivas, K.; Kumar, Rajeev; Mozumdar, Subho; Patanjali, P. K.

2004-01-01

CuO nanoparticles on sputtered SnO 2 thin-film surface exhibit a fast response speed (14 s) and recovery time (61 s) for trace level (20 ppm) H 2 S gas detection. The sensitivity of the sensor (S∼2.06x10 3 ) is noted to be high at a low operating temperature of 130 deg. C. CuO nanoparticles on SnO 2 allow effective removal of excess adsorbed oxygen from the uncovered SnO 2 surface due to spillover of hydrogen dissociated from the H 2 S-CuO interaction

Nonohmic behavior of SnO2.MnO2-based ceramics

Directory of Open Access Journals (Sweden)

Marcelo O. Orlandi

2003-06-01

Full Text Available The present paper describes the nonohmic behavior of the SnO2.MnO-based system and analyzes the influence of the sintering time and the Nb2O5 concentration on this system's electrical properties. A nonlinear coefficient of ~7 was obtained for a 0.2 mol%-doped Nb2O5 composition, which is comparable to other values reported in the literature for the ternary SnO2-based systems. A recent barrier formation model proposed in the literature to explain the nonlinear electrical behavior of SnO2-based systems is used to clarify the role of the MnO constituent in the formation of the barrier, taking into account the influence of segregated atoms, precipitated phase and oxygen species in the grain boundary region.

Ab initio study of thermoelectric properties of doped SnO_2 superlattices

International Nuclear Information System (INIS)

Borges, P.D.; Silva, D.E.S.; Castro, N.S.; Ferreira, C.R.; Pinto, F.G.; Tronto, J.; Scolfaro, L.

2015-01-01

Transparent conductive oxides, such as tin dioxide (SnO_2), have recently shown to be promising materials for thermoelectric applications. In this work we studied the thermoelectric properties of Fe-, Sb- and Zn-uniformly doping and co-doping SnO_2, as well as of Sb and Zn planar (or delta)-doped layers in SnO_2 forming oxide superlattices (SLs). Based on the semiclassical Boltzmann transport equations (BTE) in conjunction with ab initio electronic structure calculations, the Seebeck coefficient (S) and figure of merit (ZT) are obtained for these systems, and are compared with available experimental data. The delta doping approach introduces a remarkable modification in the electronic structure of tin dioxide, when compared with the uniform doping, and colossal values for ZT are predicted for the delta-doped oxide SLs. This result is a consequence of the two-dimensional electronic confinement and the strong anisotropy introduced by the doped planes. In comparison with the uniformly doped systems, our predictions reveal a promising use of delta-doped SnO_2 SLs for enhanced S and ZT, which emerge as potential candidates for thermoelectric applications. - Graphical abstract: Band structure and Figure of merit for SnO2:Sb superlattice along Z direction, P. D. Borges, D. E. S. Silva, N. S. Castro, C. R. Ferreira, F. G. Pinto, J. Tronto and L. Scolfaro, Ab initio study of thermoelectric properties of doped SnO2 superlattices. - Highlights: • Thermoelectric properties of SnO_2-based alloys and superlattices. • High figure of merit is predicted for planar-doped SnO_2 superlattices. • Nanotechnology has an important role for the development of thermoelectric devices.

Pebble fabrication of super advanced tritium breeders using a solid solution of Li2+xTiO3+y with Li2ZrO3

Directory of Open Access Journals (Sweden)

Tsuyoshi Hoshino

2016-12-01

Full Text Available Lithium titanate with excess lithium (Li2+xTiO3+y is one of the most promising candidates among advanced tritium breeders for demonstration power plant reactors because of its good tritium release characteristics. However, the tritium breeding ratio (TBR of Li2+xTiO3+y is smaller than that of e.g., Li2O or Li8TiO6 because of its lower Li density. Therefore, new Li-containing ceramic composites with both high stability and high Li density have been developed. Thus, this study focused on the development of a solid solution with a new characteristic. The solid-solution pebbles of Li2+xTiO3+y with Li2ZrO3 (Li2+x(Ti,ZrO3+y, designated as LTZO, were fabricated by an emulsion method. The X-ray diffraction patterns of sintered LTZO pebbles are approximately the same as those of Li2+xTiO3+y pebbles, and no peaks attributable to Li2ZrO3 are observed. These results demonstrate that LTZO pebbles are not a two-phase material but rather a solid solution. Furthermore, LTZO pebbles were easily sintered under air. Thus, the LTZO solid solution is a candidate breeder material for super advanced (SA tritium breeders.

Structural and magnetic properties of the (Ca1-xNax)(Fe2-xTix)O4 solid solution (0 ≤ x ≤ 1)

International Nuclear Information System (INIS)

Zouari, S.; Ranno, L.; Cheikh-Rouhou, A.; Isnard, O.; Wolfers, P.; Bordet, P.; Strobel, P.

2008-01-01

New compounds corresponding to the (Ca 1-x Na x )(Fe 2-x Ti x )O 4 formula with 0 ≤ x ≤ 1 were prepared by solid state reactions at 1100 deg. C in air. A continuous solid solution was found between end members CaFe 2 O 4 and NaFeTiO 4 . The evolution of structural parameters and bonding geometry with composition is discussed in detail. Magnetic measurements show that the antiferromagnetic ordering known in CaFe 2 O 4 is suppressed for all x values investigated (x ≥ 0.2). The absence of crystallographic transition at low temperature was checked by X-ray diffraction down to 10 K. The magnetic structure of CaFe 2 O 4 was redetermined from powder neutron diffraction. Spins on the two iron sites order antiparallel (F z F z spin arrangement), as described previously. The difference in magnetic moments on Fe 1 and Fe 2 sites result in a ferrimagnetic configuration with net moment 2.72μ B at 2 K

Shell model for BaTiO3-Bi(Zn1/2Ti1/2)O3 perovskite solid solutions

Science.gov (United States)

Vielma, J.; Jackson, D.; Roundy, D.; Schneider, G.

2010-03-01

Even though the composition of BaTiO3-Bi(Zn1/2Ti1/2)O3 perovskite solid solutions is similar to other ferroelectric compounds, the dielectric response is unusual. Results of permittivity measurements as a function of temperature show a diffuse phase transition indicative of a weakly coupled relaxor behavior.footnotetextC. C. Huang and D. P. Cann, J. Appl. Phys. 104, 024117 (2008) To investigate the weakly coupled relaxor behavior in these materials at intermediate length scales we are developing a newly calibrated shell model based on first-principles supercell calculations of both the solid solution and its compositional endpoints. Initial results for its phase diagram will presented.

Synthesis and characterization of hollow {alpha}-Fe{sub 2}O{sub 3} sub-micron spheres prepared by sol-gel

Energy Technology Data Exchange (ETDEWEB)

Leon, Lizbet, E-mail: lizbetlf@gmail.com; Bustamante, Angel; Osorio, Ana; Olarte, G. S. [Universidad Nacional Mayor de San Marcos (Peru); Santos Valladares, Luis De Los, E-mail: ld301@cam.ac.uk; Barnes, Crispin H. W. [University of Cambridge, Cavendish Laboratory (United Kingdom); Majima, Yutaka [Tokyo Institute of Technology, Materials and Structures Laboratory (Japan)

2011-11-15

In this work we report the preparation of magnetic hematite hollow sub-micron spheres ({alpha}-Fe{sub 2}O{sub 3}) by colloidal suspensions of ferric nitrate nine-hydrate (Fe(NO{sub 3}){sub 3}{center_dot}9H{sub 2}O) particles in citric acid solution by following the sol-gel method. After the gel formation, the samples were annealed at different temperatures in an oxidizing atmosphere. Annealing at 180 Degree-Sign C resulted in an amorphous phase, without iron oxide formation. Annealing at 250 Degree-Sign C resulted in coexisting phases of hematite, maghemite and magnetite, whereas at 400 Degree-Sign C, only hematite and maghemite were found. Pure hematite hollow sub-micron spheres with porous shells were formed after annealing at 600 Degree-Sign C. The characterization was performed by X-ray diffraction (XRD), Moessbauer spectroscopy (MS) and scanning electron microscopy (SEM).

Sintering and electrical properties of titania- and zirconia-containing In2O3-SnO2 (ITO) ceramics

International Nuclear Information System (INIS)

Nadaud, N.; Nanot, M.; Bock, P.

1994-01-01

The deposition rate and film quality of In 2 O 3 -SnO 2 (ITO) transparent electrodes processed by sputtering are improved when using dense sputtering targets. Unfortunately, ITO ceramics do not sinter easily. It is shown that addition of TiO 2 ( 2 was also investigated

Photoinduced structural transformation of SrFeO3 and Ca2Fe2O5 during photodegradation of methyl orange

International Nuclear Information System (INIS)

Yang Yang; Cao Zhengquan; Jiang Yinshan; Liu Lihua; Sun Yanbin

2006-01-01

Photodegradation of methyl orange solution under UV light irradiation have been studied over photocatalyst perovskite SrFeO 3 and brownmillerite Ca 2 Fe 2 O 5 . XRD and FTIR analysis show that both SrFeO 3 and Ca 2 Fe 2 O 5 transform to carbonates during the photodegradation process of methyl orange. This result indicates that UV light irradiation induce a photochemical reaction between photocatalysts and CO 2 released from the photodegradation of methyl orange. The photochemical reaction between photocatalysts and CO 2 is responsible for the transformation of the structures. The fact that SrFeO 3 has better photocatalytic property and endures serious transformation than Ca 2 Fe 2 O 5 is due to existence of unstable Fe (IV) in the perovskite structure of SrFeO 3. Such kind of Fe (IV) makes perovskite structure unstable and sensitive to ambient (especially sensitive to UV light irradiation)

Coexistence of room temperature ferroelectricity and ferrimagnetism in multiferroic BiFeO3-Bi0.5Na0.5TiO3 solid solution

International Nuclear Information System (INIS)

Tian, Z.M.; Wang, C.H.; Yuan, S.L.; Wu, M.S.; Ma, Z.Z.; Duan, H.N.; Chen, L.

2011-01-01

Highlights: → In this study, the coexistence of ferroelectrics and ferrimagnetism have been observed at room temperature for the (1 - x)BiFeO 3 -xBi 0.5 Na 0.5 TiO 3 (x = 0.37) solid solutions. → X-ray diffraction and Raman spectroscopy measurements show a single-phase perovskite structure with no impurities identified. → A magnetic transition from paramagnetic (PM) to ferrimagnetic (Ferri) ordering is observed for the solution with Curie temperature T C ∼ 330 K. - Abstract: The structure, ferroelectric and magnetic properties of (1 - x)BiFeO 3 -xBi 0.5 Na 0.5 TiO 3 (x = 0.37) solid solution fabricated by a sol-gel method have been investigated. X-ray diffraction and Raman spectroscopy measurements show a single-phase perovskite structure with no impurities identified. Compared with pure BiFeO 3 , the coexistence of ferroelectricity and ferrimagnetism have been observed at room temperature for the solution with remnant polarization P r = 1.41 μC/cm 2 and remnant magnetization M r = 0.054 emu/g. Importantly, a magnetic transition from ferrimagnetic (FM) ordering to paramagnetic (PM) state is observed, with Curie temperature T C ∼ 330 K, being explained in terms of the suppression of cycloid spin configuration by the structural distortion.

Nanosized {alpha}-LiFeO{sub 2} as electrochemical supercapacitor electrode in neutral sulfate electrolytes

Energy Technology Data Exchange (ETDEWEB)

Santos-Pena, J., E-mail: iq2sanpe@uco.e [Departamento de Quimica Inorganica e Ingenieria Quimica, Edificio Marie Curie, Campus de Rabanales, Universidad de Cordoba, 14071 Cordoba (Spain); Crosnier, O.; Brousse, T. [Laboratoire de Genie des Materiaux et Procedes Associes, Ecole Polytechnique de l' Universite de Nantes, Site de la Chantrerie, rue Christian Pauc s/n, 44376 Nantes Cedex 3 (France)

2010-10-30

In this work we have explored the electrochemical properties of two lithiated iron oxide powders for supercapacitor purposes. These samples mainly consisted of {alpha}-LiFeO{sub 2} in nanosized or micrometric form. Electrolyte was an aqueous 0.5 M Li{sub 2}SO{sub 4} solution and voltage range studied was between 0 and -0.7 V vs. a Ag/AgCl reference electrode. As expected, electrochemical performance was dependent on the particle size. When electrolyte was deaerated a stable capacitance of {approx}50 F g{sup -1} is provided by the nanosized sample for several hundred cycles. Other sulfate based salts (Na{sub 2}SO{sub 4}, K{sub 2}SO{sub 4}, Cs{sub 2}SO{sub 4}) were investigated as electrolytes but only Li{sub 2}SO{sub 4} leads to a stable capacitance upon cycling, probably due to lithium intercalation. An hybrid cell consisting of this sample and MnO{sub 2} as negative and positive electrodes, respectively, delivered 0.3 F cm{sup -2} (10 F g{sup -1}). Although these values are lower than reported for other aqueous hybrid cell, {alpha}-LiFeO{sub 2}/MnO{sub 2} asymmetric capacitor is interesting from both, an economic and an environmental point of view.

Microstructural investigation and SnO nanodefects in spray-pyrolyzed SnO2 thin films

DEFF Research Database (Denmark)

Thanachayanont, Chanchana; Yordsri, Visittapong; Boothroyd, Chris

2011-01-01

Spray pyrolysis is one of the most cost-effective methods to prepare SnO2 films due to its ability to deposit large uniform area, low fabrication cost, simplicity and low deposition temperature. Conventionally, scanning electron microscopy (SEM) and X-Ray Diffraction (XRD) are routinely used...... diffraction (CBED). It was found that large grain-size vertically-aligned columnar SnO2 grains were formed after a few layers of small grain-size randomly oriented SnO2 grains. Moreover, CBED showed the presence of SnO nanodefects that had not been reported before and could not be detected by SEM or XRD....

Interaction-induced partitioning and magnetization jumps in the mixed-spin oxide FeTiO3-Fe2O3.

Science.gov (United States)

Charilaou, M; Sahu, K K; Zhao, S; Löffler, J F; Gehring, A U

2011-07-29

In this study we report on jumps in the magnetic moment of the hemo-ilmenite solid solution (x)FeTiO(3)-(1-x)Fe(2)O(3) above Fe(III) percolation at low temperature (T<3 K). The first jumps appear at 2.5 K, one at each side of the magnetization loop, and their number increases with decreasing temperature and reaches 5 at T=0.5 K. The jumps occur after field reversal from a saturated state and are symmetrical in the trigger field and intensity with respect to the field axis. Moreover, an increase of the sample temperature by 2.8% at T=2.0 K indicates the energy released after the ignition of the magnetization jump, as the spin-currents generated by the event are dissipated in the lattice. The magnetization jumps are further investigated by Monte Carlo simulations, which show that these effects are a result of magnetic interaction-induced partitioning on a sublattice level. © 2011 American Physical Society

The solubility and site preference of Fe3+ in Li7-3xFexLa3Zr2O12 garnets

Science.gov (United States)

Rettenwander, D.; Geiger, C. A.; Tribus, M.; Tropper, P.; Wagner, R.; Tippelt, G.; Lottermoser, W.; Amthauer, G.

2015-10-01

A series of Fe3+-bearing Li7La3Zr2O12 (LLZO) garnets was synthesized using solid-state synthesis methods. The synthetic products were characterized compositionally using electron microprobe analysis and inductively coupled plasma optical emission spectroscopy (ICP-OES) and structurally using X-ray powder diffraction and 57Fe Mössbauer spectroscopy. A maximum of about 0.25 Fe3+ pfu could be incorporated in Li7-3xFexLa3Zr2O12 garnet solid solutions. At Fe3+ concentrations lower than about 0.16 pfu, both tetragonal and cubic garnets were obtained in the synthesis experiments. X-ray powder diffraction analysis showed only a garnet phase for syntheses with starting materials having intended Fe3+ contents lower than 0.52 Fe3+ pfu. Back-scattered electron images made with an electron microprobe also showed no phase other than garnet for these compositions. The lattice parameter, a0, for all solid-solution garnets is similar with a value of a0≈12.98 Å regardless of the amount of Fe3+. 57Fe Mössbauer spectroscopic measurements indicate the presence of poorly- or nano-crystalline FeLaO3 in syntheses with Fe3+ contents greater than 0.16 Fe3+ pfu. The composition of different phase pure Li7-3xFexLa3Zr2O12 garnets, as determined by electron microprobe (Fe, La, Zr) and ICP-OES (Li) measurements, give Li6.89Fe0.03La3.05Zr2.01O12, Li6.66Fe0.06La3.06Zr2.01O12, Li6.54Fe0.12La3.01Zr1.98O12, and Li6.19Fe0.19La3.02Zr2.04O12. The 57Fe Mössbauer spectrum of cubic Li6.54Fe0.12La3.01Zr1.98O12 garnet indicates that most Fe3+ occurs at the special crystallographic 24d position, which is the standard tetrahedrally coordinated site in garnet. Fe3+ in smaller amounts occurs at a general 96h site, which is only present for certain Li-oxide garnets, and in Li6.54Fe0.12La3.01Zr1.98O12 this Fe3+ has a distorted 4-fold coordination.

Rapid removal of uranium from aqueous solutions using magnetic Fe3O4@SiO2 composite particles.

Science.gov (United States)

Fan, Fang-Li; Qin, Zhi; Bai, Jing; Rong, Wei-Dong; Fan, Fu-You; Tian, Wei; Wu, Xiao-Lei; Wang, Yang; Zhao, Liang

2012-04-01

Rapid removal of U(VI) from aqueous solutions was investigated using magnetic Fe(3)O(4)@SiO(2) composite particles as the novel adsorbent. Batch experiments were conducted to study the effects of initial pH, amount of adsorbent, shaking time and initial U(VI) concentrations on uranium sorption efficiency as well as the desorbing of U(VI). The sorption of uranium on Fe(3)O(4)@SiO(2) composite particles was pH-dependent, and the optimal pH was 6.0. In kinetics studies, the sorption equilibrium can be reached within 180 min, and the experimental data were well fitted by the pseudo-second-order model, and the equilibrium sorption capacities calculated by the model were almost the same as those determined by experiments. The Langmuir sorption isotherm model correlates well with the uranium sorption equilibrium data for the concentration range of 20-200 mg/L. The maximum uranium sorption capacity onto magnetic Fe(3)O(4)@SiO(2) composite particles was estimated to be about 52 mg/g at 25 °C. The highest values of uranium desorption (98%) was achieved using 0.01 M HCl as the desorbing agent. Fe(3)O(4)@SiO(2) composite particles showed a good selectivity for uranium from aqueous solution with other interfering cation ions. Present study suggested that magnetic Fe(3)O(4)@SiO(2) composite particles can be used as a potential adsorbent for sorption uranium and also provided a simple, fast separation method for removal of heavy metal ion from aqueous solution. Copyright © 2011 Elsevier Ltd. All rights reserved.

Effect of applied voltage on the structural properties of SnO2 nanostuctures grown on indium-tin-oxide coated glass substrates.

Science.gov (United States)

Lee, Dea Uk; Yun, Dong Yeol; No, Young Soo; Hwang, Jun Ho; Lee, Chang Hun; Kim, Tae Whan

2013-11-01

SnO2 nanostuctures were formed on indium-tin-oxide (ITO)-coated glass substrates by using an electrochemical deposition (ECD) method. X-ray photoelectron spectroscopy (XPS) spectra showed the existence of elemental Sn and O in the samples, indicative of the formation of SnO2 materials. An XPS spectrum showing the O 1s peak at a binding energy of 531.5 eV indicated that the oxygen atoms were bonded to the SnO2. Field-emission scanning electron microscopy (FE-SEM) images showed that the samples formed by using the ECD method had SnO2 nanostructures with a size between 280 and 350 nm. FE-SEM images showed that the size of the SnO2 nanostructures formed at 65 degrees C for 30 min increased with decreasing applied voltage. X-ray diffraction (XRD) patterns showed that the SnO2 nanostrucures had tetragonal structures with cell parameters of a = 4.738 A and c = 3.187 A. XRD results showed that the peak intensity of the (110) plane increased with decreasing applied voltage, indicative of a preferencial orientation of the (110) plane.

Enhanced NH3 gas sensing performance based on electrospun alkaline-earth metals composited SnO2 nanofibers

International Nuclear Information System (INIS)

Xu, Shuang; Kan, Kan; Yang, Ying; Jiang, Chao; Gao, Jun; Jing, Liqiang; Shen, Peikang; Li, Li

2015-01-01

Highlights: • The small-sized SnO 2 (5–7 nm) were obtained by adding the alkaline-earth. • Sr-composited SnO 2 nanofibers showed uniform nanotubes structure (Sr/SnO 2 ). • Sr/SnO 2 showed an excellent sensing performance to NH 3 at room temperature. - Abstract: One-dimensional alkaline-earth metals composited SnO 2 (Ae/SnO 2 ) nanofibres were fabricated via electrospinning technique, followed by thermal treatment at 600 °C for 5 h. Transmission electron microscopy (TEM) studies showed that the nanoparticles size of Ae/SnO 2 was 5–7 nm, which was smaller than the pristine SnO 2 nanorods attached by 20 nm nanoparticles. Moreover, Sr/SnO 2 nanocomposites showed uniform nanotubes structure with the wall thickness of about 30 nm, in which all the nanoparticles were connected to their neighbors by necks. The Sr/SnO 2 nanotubes exhibited an excellent sensing response toward NH 3 gas at room temperature, lower detection limit (10 ppm), faster response time (6 s towards 2000 ppm∼16 s towards 10 ppm) and better reversibility compared to the pristine SnO 2 nanorods. The enhanced sensor performances were attributed to the higher conductivity of the Sr/SnO 2 . Mott–Schottky plots (M–S) and electrochemical impedance spectroscopy (EIS) measurements indicated that the carrier density of Sr/SnO 2 nanotubes was 3 fold of that pristine SnO 2

Solid state reaction studies in Fe{sub 3}O{sub 4}–TiO{sub 2} system by diffusion couple method

Energy Technology Data Exchange (ETDEWEB)

Ren, Zhongshan [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083 (China); School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Hu, Xiaojun, E-mail: huxiaojun@ustb.edu.cn [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083 (China); School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China); Xue, Xiangxin [School of Materials and Metallurgy, Northeastern University, Shenyang 110006 (China); Chou, Kuochih [State Key Laboratory of Advanced Metallurgy, University of Science and Technology Beijing, Beijing 100083 (China); School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083 (China)

2013-12-15

Highlights: •The solid state reactions of Fe2O3-TiO2 system was studied by the diffusion couple method. •Different products were formed by diffusion, and the FeTiO3 was more stable phase. •The inter-diffusion coefficients and diffusion activation energy were estimated. -- Abstract: The solid state reactions in Fe{sub 3}O{sub 4}–TiO{sub 2} system has been studied by diffusion couple experiments at 1323–1473 K, in which the oxygen partial pressure was controlled by the CO–CO{sub 2} gas mixture. The XRD analysis was used to confirm the phases of the inter-compound, and the concentration profiles were determined by electron probe microanalysis (EPMA). Based on the concentration profile of Ti, the inter-diffusion coefficients in Fe{sub 3}O{sub 4} phase, which were both temperature and concentration of Ti ions dependent, were calculated by the modified Boltzmann–Matano method. According to the relation between the thickness of diffusion layer and temperature, the diffusion coefficient of the Fe{sub 3}O{sub 4}–TiO{sub 2} system was obtained. According to the Arrhenius equation, the estimated diffusion activation energy was about 282.1 ± 18.8 kJ mol{sup −1}.

Moessbauer spectroscopy study on the hydrothermal transformation α-FeOOH → α-Fe2O3

International Nuclear Information System (INIS)

Barb, D.; Diamandescu, L.; Mihaila-Tarabsanu, D.; Rusi, A.; Moraria, M.

1990-01-01

The reaction kinetics of the hydrothermal transformation α-FeOOH→α-Fe 2 O 3 was studied by means of Moessbauer spectroscopy. From the reaction isotherms, a monomolecular, first order reaction was found to characterise the hydrothermal transformation of alpha oxihydroxide to the alpha iron oxide. The rate constant as well as the activation energy of this process were determined. No intermediate phases were identified in the hydrothermal samples. The thermodynamic properties of the hydrothermal system α-FeOOH→α-Fe 2 O 3 in correlation with Moessbauer spectroscopy data are discussed. (orig.)

Crystal structure and Mössbauer effect in multiferroic 0.5BiFeO3-0.5Pb(Fe0.5Ta0.5O3 solid solution

Directory of Open Access Journals (Sweden)

Stoch Agata

2017-06-01

Full Text Available Multiferroic 0.5BiFeO3-0.5Pb(Fe0.5Ta0.5O3 solid solution is a material that exhibits ferroelectric and antiferromagnetic orderings in ambient temperature. The solid solution was obtained as a result of a conventional reaction in a solid state. The obtained material is a dense, fine-grained sinter whose surface was observed by scanning electron microscopy (SEM and stoichiometry was confirmed by energy dispersive X-ray spectroscopic (EDS analysis. According to the X-ray powder diffraction (XRD measurements, the main phase is R3c space group with admixture of Pm-3m regular phase. Small contribution of pyrochlore-like phase was also observed. Mössbauer spectroscopy suggested random distribution of Fe3+/Ta5+ cations in the B sites of ABO3 compound. Reduction of the magnetic hyperfine field with an increase in the substitution of Ta5+ in Fe3+ neighbourhood was also observed.

Thermodynamics of CoAl2O4-CoGa2O4 solid solutions

International Nuclear Information System (INIS)

Lilova, Kristina I.; Navrotsky, Alexandra; Melot, Brent C.; Seshadri, Ram

2010-01-01

CoAl 2 O 4 , CoGa 2 O 4 , and their solid solution Co(Ga z Al 1-z ) 2 O 4 have been studied using high temperature oxide melt solution calorimetry in molten 2PbO.B 2 O 3 at 973 K. There is an approximately linear correlation between lattice parameters, enthalpy of formation from oxides, and the Ga content. The experimental enthalpy of mixing is zero within experimental error. The cation distribution parameters are calculated using the O'Neill and Navrotsky thermodynamic model. The enthalpies of mixing calculated from these parameters are small and consistent with the calorimetric data. The entropies of mixing are calculated from site occupancies and compared to those for a random mixture of Ga and Al ions on octahedral site with all Co tetrahedral and for a completely random mixture of all cations on both sites. Despite a zero heat of mixing, the solid solution is not ideal in that activities do not obey Raoult's Law because of the more complex entropy of mixing. - Graphical abstract: Measured enthalpies of mixing of CoAl 2 O 4 -CoGa 2 O 4 solid solutions are close to zero but entropies of mixing reflect the complex cation distribution, so the system is not an ideal solution.

Synthesis of {alpha}-Fe{sub 2}O{sub 3} nanobelts and nanoflakes by thermal oxidation and study to their magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Su Xinghua [School of Materials Science and Engineering, Chang' an University, Xi' an 710061 (China); Yu Chengshou [Department of Materials Science and Engineering, Lanzhou University, Lanzhou 730000 (China); Qiang Chengwen, E-mail: qiangchw04@gmail.com [Department of Materials Science and Engineering, Lanzhou University, Lanzhou 730000 (China); Institute of Modern Physics, Chinese Academy of Science, Lanzhou 730000 (China)

2011-08-15

{alpha}-Fe{sub 2}O{sub 3} nanobelts and nanoflakes have been successfully synthesized by oxidation of iron-coated ITO glass in air. The X-ray diffraction, Raman spectrum and scanning electron microscopy are carried out to characterize the nanobelts and nanoflakes. The formation mechanism has been presented. Significantly, the magnetic investigations show that the magnetic properties are strongly shape-dependent. The magnetization measurements of belt-like and flake-like {alpha}-Fe{sub 2}O{sub 3} in perpendicular exhibit ferromagnetic feature with the coercivity (H{sub c}) and saturation magnetization (M{sub s}) of 334.5 Oe and 1.35 emu/g, 239.5 Oe and 0.12 emu/g, respectively. For the parallel, belt-like and flake-like {alpha}-Fe{sub 2}O{sub 3} also exhibit ferromagnetic feature with the H{sub c} and M{sub s} of 205.5 Oe and 1.44 emu/g, 159.6 Oe and 0.15 emu/g, respectively.

Comparisons of multilayer H2O adsorption onto the (110) surfaces of alpha-TiO2 and SnO2 as calculated with density functional theory.

Science.gov (United States)

Bandura, Andrei V; Kubicki, James D; Sofo, Jorge O

2008-09-18

Mono- and bilayer adsorption of H2O molecules on TiO2 and SnO 2 (110) surfaces has been investigated using static planewave density functional theory (PW DFT) simulations. Potential energies and structures were calculated for the associative, mixed, and dissociative adsorption states. The DOS of the bare and hydrated surfaces has been used for the analysis of the difference between the H2O interaction with TiO2 and SnO 2 surfaces. The important role of the bridging oxygen in the H2O dissociation process is discussed. The influence of the second layer of H2O molecules on relaxation of the surface atoms was estimated.

Profound Interfacial Effects in CoFe2O4/Fe3O4 and Fe3O4/CoFe2O4 Core/Shell Nanoparticles

Science.gov (United States)

Polishchuk, Dmytro; Nedelko, Natalia; Solopan, Sergii; Ślawska-Waniewska, Anna; Zamorskyi, Vladyslav; Tovstolytkin, Alexandr; Belous, Anatolii

2018-03-01

Two sets of core/shell magnetic nanoparticles, CoFe2O4/Fe3O4 and Fe3O4/CoFe2O4, with a fixed diameter of the core ( 4.1 and 6.3 nm for the former and latter sets, respectively) and thickness of shells up to 2.5 nm were synthesized from metal chlorides in a diethylene glycol solution. The nanoparticles were characterized by X-ray diffraction, transmission electron microscopy, and magnetic measurements. The analysis of the results of magnetic measurements shows that coating of magnetic nanoparticles with the shells results in two simultaneous effects: first, it modifies the parameters of the core-shell interface, and second, it makes the particles acquire combined features of the core and the shell. The first effect becomes especially prominent when the parameters of core and shell strongly differ from each other. The results obtained are useful for optimizing and tailoring the parameters of core/shell spinel ferrite magnetic nanoparticles for their use in various technological and biomedical applications.

Positron annihilation study of YBa2Cu3Oy superconductors doped with SnO2

International Nuclear Information System (INIS)

Chen, A.; Zhi, Y.; Li Biaorong; Wang Shaojie

1992-01-01

The positron annihilation lifetime spectra of YBa 2 Cu 3 O y superconductors doped with SnO 2 were measured. The results indicate that the tin element substitutes for Cu(1) sites. A brief discussion is given based on the experimental results. (orig.)

Dually fixed SnO2 nanoparticles on graphene nanosheets by polyaniline coating for superior lithium storage.

Science.gov (United States)

Dong, Yanfeng; Zhao, Zongbin; Wang, Zhiyu; Liu, Yang; Wang, Xuzhen; Qiu, Jieshan

2015-02-04

Dually fixed SnO2 nanoparticles (DF-SnO2 NPs) on graphene nanosheets by a polyaniline (Pani) coating was successfully fabricated via two facile wet chemistry processes, including anchoring SnO2 NPs onto graphene nanosheets via reducing graphene oxide by Sn(2+) ion, followed by in situ surface sealing with the Pani coating. Such a configuration is very appealing anode materials in LIBs due to several structural merits: (1) it prevents the aggregation of SnO2 NPs, (2) accommodates the structural expanding of SnO2 NPs during lithiation, (3) ensures the stable as-formed solid electrolyte interface films, and (4) effectively enhances the electronic conductivity of the overall electrode. Therefore, the final DF-SnO2 anode exhibits stable cycle performance, such as a high capacity retention of over 90% for 400 cycles at a current density of 200 mA g(-1) and a long cycle life up to 700 times at a higher current density of 1000 mA g(-1).

Nanostructured Fe2O3/Al2O3 Adsorbent for removal of As (V from water

Directory of Open Access Journals (Sweden)

Faranak Akhlaghian

2017-04-01

Full Text Available The presence of arsenate in drinking water causes adverse health effects including skin lesions, diabetes, cancer, damage to the nervous system, and cardiovascular diseases. Therefore, the removal of As (V from water is necessary. In this work, nanostructured adsorbent Fe2O3/Al2O3 was synthesized via the sol-gel method and applied to remove arsenate from polluted waters. First, the Fe2O3 load of the adsorbent was optimized. The Fe2O3/Al2O3 adsorbent was characterized by means of XRF, XRD, ASAP, and SEM techniques. The effects of the operating conditions of the batch process of As (V adsorption such as pH, adsorbent dose, contact time, and initial concentration of As (V solution were studied, and optimized. The thermodynamic study of the process showed that arsenate adsorption was endothermic. The kinetic model corresponded to the pseudo-second-order model. The Langmuir adsorption isotherm was better fitted to the experimental data. The Fe2O3/Al2O3 adsorbent was immobilized on leca granules and applied for As (V adsorption. The results showed that the immobilization of Fe2O3/Al2O3 on leca particles improved the As (V removal efficiency.

Synthesis, structural and semiconducting properties of Ba(Cu1/3 Sb2/3)O3-PbTiO3 solid solutions

Science.gov (United States)

Singh, Chandra Bhal; Kumar, Dinesh; Prashant, Verma, Narendra Kumar; Singh, Akhilesh Kumar

2018-05-01

We report the synthesis and properties of a new solid solution 0.05Ba(Cu1/3Sb2/3)O3-0.95PbTiO3 (BCS-PT) which shows the semiconducting properties. In this study, we have designed new perovskite-type (ABO3) solid solution of BCS-PT that have tunable optical band gap. BCS-PT compounds were prepared by conventional solid-state reaction method and their structural, micro-structural and optical properties were analyzed. The calcination temperature for BCS-PT solid solutions has been optimized to obtain a phase pure system. The Reitveld analysis of X-ray data show that all samples crystallize in tetragonal crystal structure with space group P4mm. X-ray investigation revealed that increase in calcination temperature led to increase of lattice parameter `a' while `c' parameter value lowered. The band gap of PbTiO3 is reduced from 3.2 eV to 2.8 eV with BCS doping and with increasing calcination temperature it further reduces to 2.56 eV. The reduced band gap indicated that the compounds are semiconducting and can be used for photovoltaic device applications.

Incorporation of sol-gel SnO2:Sb into nanoporous SiO2

International Nuclear Information System (INIS)

Canut, B.; Blanchin, M.G.; Ramos-Canut, S.; Teodorescu, V.; Toulemonde, M.

2006-01-01

Silicon oxide films thermally grown on Si(1 0 0) wafers were irradiated with 200 MeV 197 Au ions in the 10 9 -10 1 cm -2 fluence range. The targets were then etched at room temperature in aqueous HF solution (1 vol.%) for various durations. Atomic force microscopy (AFM) in the tapping mode was used to probe the processed surfaces. Conical holes with a low size dispersion were evidenced. Their surface diameter varies between 20 and 70 nm, depending on the etching time. Sol-gel dip coating technique, associated with a further annealing treatment performed at 500 o C for 15 min, was used to fill the nanopores created in SiO 2 with a transparent conductive oxide (SnO 2 doped with antimony). Transmission electron microscopy (TEM) performed on cross-sectional specimen showed that SnO 2 :Sb crystallites of ∼5 nm mean size are trapped in the holes without degrading their geometry

Morphologically controlled synthesis, structural and optical properties of CeO2/SnO2 nanocomposites

Directory of Open Access Journals (Sweden)

S. Usharani

2017-09-01

Full Text Available CeO2/SnO2 nanocomposites with different dimensional nanostructures were synthesized by a wet chemical method, using various surfactants such as SDS, CTAB and Triton X-100. The prepared CeO2/SnO2 samples were analyzed by X-ray diffraction (XRD, Fourier transform infrared (FTIR, Transmission electron microscopy (TEM, UV-Diffuse Reflectance Spectroscopy (UV-DRS, and Photoluminescence (PL spectroscopy. The XRD patterns reveal the presence of a mixed phase of SnO2 and CeO2; The TEM analysis showed the mixed morphology of uniformly dispersed spherical with ellipsoidal shape in the SDS assisted CeO2/SnO2 nanocomposites; whereas the nanostructure with spherical with hexagonal shapes was observed for the Triton X-100 assisted CeO2/SnO2 nanocomposites. The one dimensional (1D nanorod like structure observed for the CTAB assisted CeO2/SnO2 nanocomposites shows CTAB acting as a face-specific capping agent to form rod-shaped micelles. The room temperature photoluminescence emission studies of the CeO2/SnO2 nanocomposites showed strong peaks in the UV region, and several peaks in the visible region, which are likely to have originated from the oxygen vacancies and are potential materials for optoelectronic device applications. The UV results showed the absorption edges shifted to a high energy region and the blue shifts that occurred in all the samples.

Electrodeposition of Fe_3O_4 layer from solution of Fe_2(SO_4)_3 with addition ethylene glycol

International Nuclear Information System (INIS)

Dahlan, Dahyunir; Asrar, Allan

2016-01-01

The electrodeposition of Fe_3O_4 layer from the solution Fe_2(SO_4)_3 with the addition of ethylene glycol on Indium Tin Oxide (ITO) substrate has been performed. The electrodeposition was carried out using a voltage of 5 volts for 120 seconds, with and without the addition of 2% wt ethylene glycol. Significant effects of temperature on the resulting the samples is observed when they are heated at 400 °C. Structural characterization using X-ray diffraction (XRD) shows that all samples produce a layer of Fe_3O_4 with particle size less than 50 nanometers. The addition of ethylene glycol and the heating of the sample causes a shrinkage in particle size. The scanning electron microscopy (SEM) characterization shows that Fe_3O_4 layer resulting from the process of electrodeposition of Fe_2(SO_4)_3 without ethylene glycol, independent of whether the sample is heated or not, is uneven and buildup. Layer produced by the addition of ethylene glycol without heating produces spherical particles. On contrary, when the layer is heated the spherical particles transform to irregularly-shaped particles with smaller size.

Fe3O4 and MnO2 assembled on honeycomb briquette cinders (HBC) for arsenic removal from aqueous solutions.

Science.gov (United States)

Zhu, Jin; Baig, Shams Ali; Sheng, Tiantian; Lou, Zimo; Wang, Zhuoxing; Xu, Xinhua

2015-04-09

In this study, a novel composite adsorbent (HBC-Fe3O4-MnO2) was synthesized by combining honeycomb briquette cinders (HBC) with Fe3O4 and MnO2 through a co-precipitation process. The purpose was to make the best use of the oxidative property of MnO2 and the adsorptive ability of magnetic Fe3O4 for enhanced As(III) and As(V) removal from aqueous solutions. Experimental results showed that the adsorption capacity of As(III) was observed to be much higher than As(V). The maximum adsorption capacity (2.16 mg/g) was achieved for As(III) by using HBC-Fe3O4-MnO2 (3:2) as compared to HBC-Fe3O4-MnO2 (2:1) and HBC-Fe3O4-MnO2 (1:1). The experimental data of As(V) adsorption fitted well with the Langmuir isotherm model, whereas As(III) data was described perfectly by Freundlich model. The pseudo-second-order kinetic model was fitted well for the entire adsorption process of As(III) and As(V) suggesting that the adsorption is a rate-controlling step. Aqueous solution pH was found to greatly affect the adsorption behavior. Furthermore, co-ions including HCO3(-) and PO4(3-) exhibited greater influence on arsenic removal efficiency, whereas Cl(-), NO3(-), SO4(2-) were found to have negligible effects on arsenic removal. Five consecutive adsorption-regeneration cycles confirmed that the adsorbent could be reusable for successive arsenic treatment and can be used in real treatment applications. Copyright © 2015 Elsevier B.V. All rights reserved.

One-Pot Synthesis of Carbon-Coated SnO 2 Nanocolloids with Improved Reversible Lithium Storage Properties

KAUST Repository

Lou, Xiong Wen

2009-07-14

We report a simple glucose-mediated hydrothermal method for gram-scale synthesis of nearly monodisperse hybrid SnO 2 nanoparticles. Glucose is found to play the dual role of facilitating rapid precipitation of polycrystalline SnO 2 nanocolloids and in creating a uniform, glucose-derived, carbon-rich polysaccharide (GCP) coating on the SnO 2 nanocores. The thickness of the GCP coating can be facilely manipulated by varying glucose concentration in the synthesis medium. Carbon-coated SnO 2 nanocolloids obtained after carbonization of the GCP coating exhibit significantly enhanced cycling performance for lithium storage. Specifically, we find that a capacity of ca. 440 mA h/g can be obtained after more than 100 charge/discharge cycles at a current density of 300 mA/g in hybrid SnO 2-carbon electrodes containing as much as 1/3 of their mass in the low-activity carbon shell. By reducing the SnO 2-carbon particles with H 2, we demonstrate a simple route to carbon-coated Sn nanospheres. Lithium storage properties of the latter materials are also reported. Our results suggest that large initial irreversible losses in these materials are caused not only by the initial, presumably irreversible, reduction of SnO 2 as generally perceived in the field, but also by the formation of the solid electrolyte interface (SEI). © 2009 American Chemical Society.

Acetone sensors based on microsheet-assembled hierarchical Fe2O3 with different Fe3+ concentrations

Science.gov (United States)

Wang, Han; Yan, Lei; Li, Shuo; Li, Yu; Liu, Li; Du, Liting; Duan, Haojie; Cheng, Yali

2018-02-01

Several different morphologies of microsheet-assembled Fe2O3 have been fabricated by hydrothermal method using diverse concentrations of Fe3+ precursor solutions (0.025, 0.020, 0.015, 0.010 mol/L Fe3+). The as-synthesized materials have been characterized by scanning electron microscope (SEM), X-ray powder diffraction (XRD), and energy-dispersive X-ray spectrometry (EDS). The SEM images reflect that the morphologies of as-synthesized materials are affected by the concentrations of Fe3+ in precursor solutions. The less concentration of Fe3+, the more porous of Fe2O3 microflowers, and thinner of slices distributed on the surface. Furthermore, gas sensors based on these Fe2O3 microflowers manufactured and tested to various common gases. The optimum response value to 100 ppm acetone is 52 at the working temperature of 220 °C. Meanwhile, the Fe2O3 microflower sensors possess ultrafast response-recovery speed, which are 8 and 19 s, respectively. The possible sensing mechanism was mainly attributed to the high surface area, three-dimensional porous structure.

Effect of Bi2O3 and Nb2O5 addition on the electrical properties of grain boundaries of SnO2 ceramics

International Nuclear Information System (INIS)

Gouvea, D.; Kobori, M.H.; Las, W.C.; Santilli, C.V.; Varela, J.A.

1990-01-01

Grain boundary phenomena in SnO 2 ceramics are widely explored in gas sensor fabrication. On the other hand, the high electronic mobility in the conduction band and the energy gap width of 3,5 eV are characteristics which can lead to the formation of an intergranular potential barrier similar to those encountered in ceramic varistors. In this work, the Nb 2 O 5 and Bi 2 O 3 influence on the electrical transport mechanisms through grain boundaries in SnO 2 ceramics was investigated. The samples were characterized by measuring the electrical conductivity as a function of electric field for temperatures from 25 0 C to 200 0 C. The results were analyzed by models which are based on phenomena that occur at interfaces between semiconducting materials. (author) [pt

Epitaxial TiO 2/SnO 2 core-shell heterostructure by atomic layer deposition

KAUST Repository

Nie, Anmin

2012-01-01

Taking TiO 2/SnO 2 core-shell nanowires (NWs) as a model system, we systematically investigate the structure and the morphological evolution of this heterostructure synthesized by atomic layer deposition/epitaxy (ALD/ALE). All characterizations, by X-ray diffraction, high-resolution transmission electron microscopy, selected area electron diffraction and Raman spectra, reveal that single crystalline rutile TiO 2 shells can be epitaxially grown on SnO 2 NWs with an atomically sharp interface at low temperature (250 °C). The growth behavior of the TiO 2 shells highly depends on the surface orientations and the geometrical shape of the core SnO 2 NW cross-section. Atomically smooth surfaces are found for growth on the {110} surface. Rough surfaces develop on {100} surfaces due to (100) - (1 × 3) reconstruction, by introducing steps in the [010] direction as a continuation of {110} facets. Lattice mismatch induces superlattice structures in the TiO 2 shell and misfit dislocations along the interface. Conformal epitaxial growth has been observed for SnO 2 NW cores with an octagonal cross-section ({100} and {110} surfaces). However, for a rectangular core ({101} and {010} surfaces), the shell also derives an octagonal shape from the epitaxial growth, which was explained by a proposed model based on ALD kinetics. The surface steps and defects induced by the lattice mismatch likely lead to improved photoluminescence (PL) performance for the yellow emission. Compared to the pure SnO 2 NWs, the PL spectrum of the core-shell nanostructures exhibits a stronger emission peak, which suggests potential applications in optoelectronics. © The Royal Society of Chemistry 2012.

Structural and magnetic properties of a mechanochemically activated Ti-Fe2O3 solid mixture

International Nuclear Information System (INIS)

Cristobal, A.A.; Ramos, C.P.; Bercoff, P.G.; Conconi, S.; Aglietti, E.F.; Botta, P.M.; Lopez, J.M. Porto

2010-01-01

The mechanochemical effects on the reactivity and properties of a titanium/hematite powder mixture with molar ratio of 1/2 are investigated. Crystalline-phase structure, composition, hyperfine and magnetic behaviors were analyzed as a function of activation time by means of X-ray diffraction, scanning electron microscopy, Moessbauer spectroscopy and vibrating sample magnetometry. The results showed that at relatively short activation times metallic Ti reduces part of the ferric ions, yielding a complex product formed mainly by a mix of two solid solutions Fe 3-x Ti x O 4 (titanomagnetites), both with very different x values (0 < x < 1). Also metallic iron and superparamagnetic hematite particles were detected by Moessbauer spectroscopy. As the mechanical treatment extends the composition of the reactive mixture changes, prevailing in the end the solid solution with higher x value. In contrast, when these activated samples are thermally treated the fraction of the solid solution which is richer in Ti diminishes. This fact produces a significant variation of the saturation magnetization of the obtained material.

Structural, electrical and multiferroic characteristics of thermo-mechanically fabricated BiFeO3-(BaSr)TiO3 solid solutions

Science.gov (United States)

Behera, C.; Choudhary, R. N. P.; Das, Piyush R.

2018-05-01

A solid solution consisting of two perovskite compounds (BiFeO3 and (BaSr)TiO3) of chemical composition (Bi1/2Ba1/4Sr1/4)(Fe1/2Ti1/2)O3 has been fabricated in the low dimensional regime by thermo-mechanical (ball milling and heating) approach. The effect of particle size on the structural, micro-structural, relative permittivity, switching (ferroelectric and magnetic) and conduction phenomena of the material has been studied using various experimental techniques such as x-rays diffraction, transmission and scanning electron microscopy, ferroelectric and magnetic hysteresis, dynamic magneto-electric coupling measurement and impedance spectroscopy techniques. All the above extracted properties are found to be particle size dependent. The first order magneto-electric coupling constant is found to be 2.56, 6.6 and 8.7 mV cm‑1.Oe for 30, 60 and 90 h milled calcined (hmc) sample respectively. As the above micro/nano-material with different particle size, has a high relative dielectric constant and low tangent loss, it can be used for some multifunctional devices including capacity energy storage device in nano-electronics.

Experimental heat capacities, excess entropies, and magnetic properties of bulk and nano Fe3O4-Co3O4 and Fe3O4-Mn3O4 spinel solid solutions

Science.gov (United States)

Schliesser, Jacob M.; Huang, Baiyu; Sahu, Sulata K.; Asplund, Megan; Navrotsky, Alexandra; Woodfield, Brian F.

2018-03-01

We have measured the heat capacities of several well-characterized bulk and nanophase Fe3O4-Co3O4 and Fe3O4-Mn3O4 spinel solid solution samples from which magnetic properties of transitions and third-law entropies have been determined. The magnetic transitions show several features common to effects of particle and magnetic domain sizes. From the standard molar entropies, excess entropies of mixing have been generated for these solid solutions and compared with configurational entropies determined previously by assuming appropriate cation and valence distributions. The vibrational and magnetic excess entropies for bulk materials are comparable in magnitude to the respective configurational entropies indicating that excess entropies of mixing must be included when analyzing entropies of mixing. The excess entropies for nanophase materials are even larger than the configurational entropies. Changes in valence, cation distribution, bonding and microstructure between the mixing ions are the likely sources of the positive excess entropies of mixing.

Parts per billion-level detection of benzene using SnO2/graphene nanocomposite composed of sub-6 nm SnO2 nanoparticles

International Nuclear Information System (INIS)

Meng Fanli; Li Huihua; Kong Lingtao; Liu Jinyun; Jin Zhen; Li Wei; Jia Yong; Liu Jinhuai; Huang Xingjiu

2012-01-01

Graphical abstract: SnO 2 /graphene nanocomposite composed of 4–5 nm SnO 2 nanoparticles was synthesized by one-step wet chemical method and the form mechanism of the nanocomposite is clearly interpreted. The detection limit of the nanocomposite was as low as 5 ppb to toxic benzene. Highlights: ► We synthesized SnO 2 /graphene nanocomposite using a simple one-step wet chemical method. ► The nanocomposite composed of 4–5 nm SnO 2 nanoparticles. ► Toxic benzene was detected by such kind of nanocomposite. ► The detection limit to toxic benzene was as low as 5 ppb. - Abstract: In the present work, the SnO 2 /graphene nanocomposite composed of 4–5 nm SnO 2 nanoparticles was synthesized using a simple wet chemical method for ppb-level detection of benzene. The formation mechanism of the nanocomposite was investigated systematically by means of simultaneous thermogravimetry analysis, X-ray diffraction, and X-ray photoelectron spectroscopy cooperated with transmission electron microscopy observations. The SnO 2 /graphene nanocomposite showed a very attractive improved sensitivity to toxic volatile organic compounds, especially to benzene, compared to a traditional SnO 2 . The responses of the nanocomposite to benzene were a little higher than those to ethanol and the detection limit reached 5 ppb to benzene which is, to our best knowledge, far lower than those reported previously.

The Systematics of Activity-Composition Relations in Mg-Fe2+ Oxide and Silicate Solid Solutions

Science.gov (United States)

O'Neill, H. S.

2006-12-01

accuracy including possible systematic errors of 0.5 kJ/mol (1 st. dev.). Any asymmetry is unambiguously constrained to be very small. These results were combined with experimental data (all at or above 900ºC), for partitioning of Mg and Fe between olivine and one of ilmenite (Pownceby and O'Neill, in prep.), Ti-, Al- or Cr-spinel (O'Neill, unpublished) and pyroxenes, garnet, and various high-pressure phases (literature). Internal consistency can be checked using other available partitioning data between pairs of these phases (i.e., without olivine). Except for some of the high-pressure phases, the ferromagnesian solutions are symmetrical with W Mg-Fe decreasing with the difference in the volumes of the end-members, which in turn depends on the atomic (Mg+Fe)/O ratio. This suggests that mixing in binary amphiboles, micas and other complex ferromagnesian silicates should be nearly ideal. The discrepancies shown by the high-pressure phases may be due to Fe3+ substitutions. As a working hypothesis, it is proposed that solid solutions between cations of the same charge and roughly similar size have simple thermodynamic mixing properties, with little asymmetry, modest excess entropies and excess enthalpies proportional to the volume difference of the end-members. Order-disorder phenomena have surprisingly little effect in the high temperature regime for which experimental data are available. Refs: [1] Davies and Navrotsky, J Sol State Chem 46, 1-22, 1983. [2] O'Neill et al., CMP 146, 308-325, 2003.

Facile fabrication of robust TiO2@SnO2@C hollow nanobelts for outstanding lithium storage

Science.gov (United States)

Tian, Qinghua; Li, Lingxiangyu; Chen, Jizhang; Yang, Li; Hirano, Shin-ichi

2018-02-01

Elaborate fabrication of state-of-the-art nanostructure SnO2@C-based composites greatly contributes to alleviate the huge volume expansion issue of the SnO2 anodes. But the preparation processes of most of them are complicated and tedious, which is generally adverse to the development of SnO2@C-based composite anodes. Herein, a unique nanostructure of TiO2@SnO2@C hollow nanobelts (TiO2@SnO2@C HNBs), including the characteristics of one-dimensional architecture, sandwich protection, hollow structure, carbon coating, and a mechanically robust TiO2 support, has been fabricated by a facile approach for the first time. As anodes for lithium-ion batteries, the as-fabricated TiO2@SnO2@C HNBs exhibit an outstanding lithium storage performance, delivering capacity of 804.6 and 384. 5 mAh g-1 at 200 and even 1000 mA g-1 after 500 cycles, respectively. It is demonstrated that thus outstanding performance is mainly attributed to the unique nanostructure of TiO2@SnO2@C HNBs.

Reduction of the Curie temperature in the multiferroic Bi5Fe1+xTi3−xO15 solid solution

International Nuclear Information System (INIS)

Salazar-Kuri, U; Mendoza, M E; Silva, R; Siqueiros, J M; Gervacio-Arciniega, J J

2014-01-01

In this work, the phase diagram of the system Bi 4 Ti 3 O 12 -BiFeO 3 in the region of the solid solution Bi 5 Fe 1+x Ti 3−x O 15 was refined. The limit of solubility was determined to be at x = 0.1. The Curie temperature (T C ) of the ferroelectric phase transition was determined by dielectric permittivity measurements at 100 kHz for the phase Bi 5 FeTi 3 O 15 as well as for the solid solution. A decrease in T C from 750 °C to 742 °C (solid solution at x = 0.1) was found. These results can be explained in terms of the perturbation of the oxygen octahedral perovskite layers resulting from the substitution of Ti 4+ by Fe 3+ ions. (paper)

Theoretical prediction of morphotropic compositions in Na1/2Bi1/2TiO3-based solid solutions from transition pressures

Science.gov (United States)

Gröting, Melanie; Albe, Karsten

2014-02-01

In this article we present a method based on ab initio calculations to predict compositions at morphotropic phase boundaries in lead-free perovskite solid solutions. This method utilizes the concept of flat free energy surfaces and involves the monitoring of pressure-induced phase transitions as a function of composition. As model systems, solid solutions of Na1/2Bi1/2TiO3 with the alkali substituted Li1/2Bi1/2TiO3 and K1/2Bi1/2TiO3 and the alkaline earth substituted CaTiO3 and BaTiO3 are chosen. The morphotropic compositions are identified by determining the composition at which the phase transition pressure equals zero. In addition, we discuss the different effects of hydrostatic pressure (compression and tension) and chemical substitution on the antiphase tilts about the [111] axis (a-a-a-) present in pure Na1/2Bi1/2TiO3 and how they develop in the two solid solutions Na1/2Bi1/2TiO3-CaTiO3 and Na1/2Bi1/2TiO3-BaTiO3. Finally, we discuss the advantages and shortcomings of this simple computational approach.

Sintering of undoped SnO2 Sinterização de SnO2 não dopado

Directory of Open Access Journals (Sweden)

E. R. Leite

2003-04-01

Full Text Available Pure SnO2 sintering was studied by constant heating rate and isothermal sintering. The constant heating rate study showed no macroscopic shrinkage during the sintering process up to 1500 ºC. Pore size distribution measurements, using gas desorption, and grain size and crystallite size measurements of isothermally sintered samples showed no formation of non-densifying microstructures during the sintering process. These results are a strong indication that densification was prevented by thermodynamic factors, mainly the high ratio of gammaGB/gSV. An explanation, based on the nature of covalent bonding and the balance between attractive and repulsive forces, was proposed to explain the high gammaGB/gammaSV ratio in SnO2.A sinterização de SnO2 puro foi estudado por taxa constante de aquecimento e por sinterização isotérmica. O estudo de taxa constante de aquecimento mostrou que não ocorre retração macroscópica durante o processo de sinterização até temperaturas de 1500 ºC. Medidas de distribuição de tamanho de poros, usando adsorção de gás, tamanho de grão e tamanho de cristalito para amostras sinterizadas isotermicamente mostrou a não formação de uma microestrutura não-densificante durante o processo de sinterização. Estes resultados são um forte indicativo que a densificação foi inibida por fatores termodinâmicos, principalmente o alto valor da razão de gamaGB/gSV. Uma explicação, baseada na natureza covalente da ligação química e no balanço entre forças atrativas e repulsivas, é apresentada para explicar o alto valor da razão gamaGB/gamaSV no SnO2.

Sorption of Fe3+ , Co2+ , Ce3+ , Cs+ and Ba2+ in zeolite X

International Nuclear Information System (INIS)

Martinez M, V.

1994-01-01

The sorption behavior of Fe 3+ , Co 2+ , Ce 3+ , Cs + , and Ba 2+ in aqueous solutions, was studied in presence of zeolite X. Solutions of Fe(NO 3 ) 3 . 9 H 2 O, Co(NO 3 ) 2 . 6 H 2 O, Ce(NO 3 ) 3 . 6 H 2 O, Cs NO 3 and Ba(NO 3 ) 2 were labelled with the respectively radioactive isotopes Fe 59 , Co 60 , Cs 134 , Ba 139 and Ce 141 . 20 ml. of each solution was left in contact with 200 mg. of zeolite for different periods. Later the zeolites were separated by centrifugation from the aqueous solutions and the radioactivity of the aqueous phases was measured with a NaI(Tl) solid-state well detector coupled to a single-channel Picker analyzer or with a Gel hyper pure solid-state detector coupled to a 2048 channel pulse height analyzer. When Cs + in the aqueous solutions was left in contact with zeolite X it was found that it does not occupy all cationic sites in the zeolite due to the ionic radium effect. A similar behavior was found for the divalent ions. In all cases, when the pH was not controlled, the zeolite lost part of its crystallinity and when the divalent ions were exchanged again by Na + , the zeolite recovered completely its crystallinity. During the sorption, the ionic radius, and the charge are important parameters as well as the pH. When the pH of the solution was adjusted between 6.5 - 7.0 the crystallinity was maintained in some cases. For Fe 3+ the crystallinity after the ion exchange was 94 % and when the pH was not adjusted the crystallinity was completely lost. It was found as well that the zeolite X induces the formation of H 3 O + which competes with the cations for the sites in the zeolite. (Author)

Synthesis of Fe2O3/TiO2 nanorod-nanotube arrays by filling TiO2 nanotubes with Fe

International Nuclear Information System (INIS)

Mohapatra, Susanta K; Banerjee, Subarna; Misra, Mano

2008-01-01

Synthesis of hematite (α-Fe 2 O 3 ) nanostructures on a titania (TiO 2 ) nanotubular template is carried out using a pulsed electrodeposition technique. The TiO 2 nanotubes are prepared by the sonoelectrochemical anodization method and are filled with iron (Fe) by pulsed electrodeposition. The Fe/TiO 2 composite is then annealed in an O 2 atmosphere to convert it to Fe 2 O 3 /TiO 2 nanorod-nanotube arrays. The length of the Fe 2 O 3 inside the TiO 2 nanotubes can be tuned from 50 to 550 nm by changing the deposition time. The composite material is characterized by scanning electron microscopy, transmission electron microscopy and diffuse reflectance ultraviolet-visible studies to confirm the formation of one-dimensional Fe 2 O 3 /TiO 2 nanorod-nanotube arrays. The present approach can be used for designing variable one-dimensional metal oxide heterostructures

SnO2Nanowire Arrays and Electrical Properties Synthesized by Fast Heating a Mixture of SnO2and CNTs Waste Soot

Directory of Open Access Journals (Sweden)

Zhou Zhi-Hua

2009-01-01

Full Text Available Abstract SnO2nanowire arrays were synthesized by fast heating a mixture of SnO2and the carbon nanotubes waste soot by high-frequency induction heating. The resultant SnO2nanowires possess diameters from 50 to 100 nm and lengths up to tens of mircrometers. The field-effect transistors based on single SnO2nanowire exhibit that as-synthesized nanowires have better transistor performance in terms of transconductance and on/off ratio. This work demonstrates a simple technique to the growth of nanomaterials for application in future nanoelectronic devices.

Cytochrome c interaction with hematite ({alpha}-Fe{sub 2}O{sub 3}) surfaces

Energy Technology Data Exchange (ETDEWEB)

Eggleston, Carrick M. [Department of Geology and Geophysics, University of Wyoming, Laramie, WY 82071 (United States)]. E-mail: carrick@uwyo.edu; Khare, Nidhi [Department of Geology and Geophysics, University of Wyoming, Laramie, WY 82071 (United States); Lovelace, David M. [Department of Geology and Geophysics, University of Wyoming, Laramie, WY 82071 (United States)

2006-02-15

The interaction of metalloproteins such as cytochromes with oxides is of interest for a number of reasons, including molecular catalysis of environmentally important mineral-solution electron transfer reactions (e.g., dehalogenations) and photovoltaic applications. Iron reduction by bacteria, thought to be cytochrome mediated, is of interest for geochemical and environmental remediation reasons. As a baseline for understanding cytochrome interaction with ferric oxide surfaces, we report on the interaction of mitochondrial cytochrome c (Mcc), a well-studied protein, with hematite ({alpha}-Fe{sub 2}O{sub 3}) surfaces. Mcc sorbs strongly to hematite from aqueous solution in a narrow pH range corresponding to opposite charge on Mcc and hematite (between pH 8.5 and 10, Mcc is positively charged and hematite surfaces are negatively charged). Cyclic voltammetry of Mcc using hematite electrodes gives redox potentials characteristic of Mcc in a native conformational state, with no evidence for unfolding on the hematite surface. Atomic force microscopy imaging is consistent with a loosely attached adsorbate that is easily deformed by the AFM tip. In phosphate-containing solution, Mcc adhers to the surface more strongly. These results establish hematite as a viable material for electrochemical and spectroscopic characterization of cytochrome-mineral interaction.

PENGUJIAN AKTIVITAS KOMPOSIT Fe2O3-SiO2 SEBAGAI FOTOKATALIS PADA FOTODEGRADASI 4-KLOROFENOL (The Activity Test of Fe2O3-SiO2 Composite As Photocatalyst on 4-Chlorophenol Photodegradation

Directory of Open Access Journals (Sweden)

Eko Sri Kunarti

2009-03-01

degradation was carried out in a closed reactor equipped with UV light. In this test, the influences of irradiation time and 4-chlorophenol pH were studied.  Results showed that the composite could be prepared through sol-gel method. The Fe2O3-SiO2 composite could increase activity of 4-chlorophenol photodegradation from 11.86 % to 55.38 %. The photodegradation effectiveness was influenced by irradiating time and pH of solution. The pH of solution gave different 4-chlorophenol photodegradation effectiveness.

Electrical resistivity surface for FeO-Fe2O3-P2O5 glasses

Science.gov (United States)

Vaughan, J. G.; Kinser, D. L.

1975-01-01

The dc electrical properties and microstructure of x(FeO-Fe2O3)-(100-x)P2O5 glasses were investigated up to a maximum of x = 75 mol %. Results indicate that, in general, the minimum resistivity of the glass does not occur at equal Fe(2+) and Fe(3+) concentrations, although for the special case where x = 55 mol % the minimum does occur at Fe(2+)/Fe total = 0.5, as reported by other investigators. Evidence presented shows that the position of the minimum resistivity is a function of total iron content. The minimum shifts to glasses richer in Fe(2+) at higher total iron concentrations.

Fluorine incorporation into SnO2 nanoparticles by co-milling with polyvinylidene fluoride

Science.gov (United States)

Senna, Mamoru; Turianicová, Erika; Šepelák, Vladimír; Bruns, Michael; Scholz, Gudrun; Lebedkin, Sergei; Kübel, Christian; Wang, Di; Kaňuchová, Mária; Kaus, Maximilian; Hahn, Horst

2014-04-01

Fluorine was incorporated into SnO2 nanoparticles from polyvinylidene fluoride (PVdF) by co-milling. The incorporation process was triggered by an oxidative partial decomposition of PVdF due to the abstraction of oxygen atoms, and began soon after milling with a simultaneous decrease in the crystallite size of SnO2 from 56 nm to 19 nm, and increase in the lattice strain by a factor 7. Appearance of D and G Raman peaks indicated that the decomposition of PVdF was accompanied by the formation of nanometric carbon species. Decomposing processes of PVdF were accompanied by the continuous change in the states of F, with a decrease of C-F in PVdF and increase in Sn-F. This indicates the gradual incorporation of F into SnO2, by replacing a part of oxygen in the oxide with fluorine. These serial mechanochemical reaction processes were discussed on the basis of X-ray diffractometry, FT-IR, Raman and UV-Vis diffuse reflectance spectroscopy, transmission electron microscopy, F1s, Sn3d and C1s X-ray photoelectron spectroscopy and Auger electron spectra, as well as magic angle spinning NMR spectroscopy of 19F and 119Sn. The present findings serve as an initial stage of incorporating fluorine into SnO2 via a solvent-free solid-state process, toward the rational fabrication of fluorine doped SnO2 powders.