Development of accident tolerant FeCrAl-ODS steels utilizing Ce-oxide particles dispersion

Science.gov (United States)

Shibata, Hiroki; Ukai, Shigeharu; Oono, Naoko H.; Sakamoto, Kan; Hirai, Mutsumi

2018-04-01

FeCrAl-ODS ferritic steels with Ce-oxide dispersion instead of Y-oxide were produced for the accident tolerant fuel cladding of the light water reactor. Excess oxygen (Ex.O) was added to improve the mechanical property. The tensile strength at Ex.O = 0 is around 200 MPa at 700 °C, mainly owing to dispersed Ce2O3 particles in less than 10 nm size. The formation of the fine Ce2O3 particles is dominated by a coherent interface with ferritic matrix. With increasing Ex.O, an increased of number density of coarser Ce-Al type oxide particles over 10 nm size is responsible for the improvement of the tensile strength. Change of the type of oxide particle, CeO2, Ce2O3, CeAlO3, Al2O3, in FeCrAl-ODS steel was thermodynamically analyzed as a parameter of Ex.O.

Magnetic and transport properties of amorphous Ce-Al alloy

Science.gov (United States)

Amakai, Yusuke; Murayama, Shigeyuki; Momono, Naoki; Takano, Hideaki; Kuwai, Tomohiko

2018-05-01

Amorphous (a-)Ce50Al50 has been prepared by DC high-rate sputter method. The structure of the obtained sample has been confirmed to have an amorphous structure because there are no Bragg peaks in the X-ray diffraction measurement and have a clear exothermic peak by the differential scanning calorimetry measurement. We have measured the resistivity ρ, magnetic susceptibility χ, specific heat Cp and thermoelectric power S for a-Ce50Al50. The temperature dependence of ρ exhibits a small temperature dependence less than 10% in the whole temperature region. χ follows a Curie-Weiss behavior in the high-temperature region of T>90 K. The effective paramagnetic moment peff, estimated from C is 2.18 μB/Ce-atom. The low-temperature Cp/T increases rapidly with decreasing temperature and tends to a saturation. S(T) exhibits negative values in a wide temperature region. A minimum of S appear at around 60 K, and S decreases linearly with decreasing temperature down to 10 K. The low-temperature S is almost 0 μV/K down to 2 K. From these results, we have pointed out that present a-Ce50Al50 would be an incoherent Kondo material.

Luminescent properties of Y3Al5−xGaxO12:Ce crystals

International Nuclear Information System (INIS)

Zorenko, Yu.; Zorenko, T.; Malinowski, P.; Sidletskiy, O.; Neicheva, S.

2014-01-01

Absorption, luminescent and scintillation properties of Ce 3+ doped Y 3 Al 5−x Ga x O 12 crystals with Ga content in the x=1–5 range were investigated in this work and compared with the properties of YAG:Ce crystals. Apart from the traditional spectral methods (absorption, cathodoluminescence and light yield measurements), the intrinsic and Ce 3+ related luminescence of Y 3 Al 5−x Ga x O 12 :Ce solid-solution were also investigated using the luminescent spectroscopy under excitation by synchrotron radiation in the 3.7–25 eV range. We show that the optical properties Y 3 Al 5−x Ga x O 12 :Ce garnets monotonically change with increasing the Ga content in the x=0–3 range due to preferable localization of Ga ions in the tetrahedral position of the garnet lattice. At the highest Ga concentration (x>3) the deviation of the optical properties of Y 3 Al 5−x Ga x O 12 :Ce garnets is observed from the respective properties of these crystals with Ga content in the x=0–3 range due to occupation by Ga ions of the octahedral position in the garnet host. - Highlights: • Different dependence of optical properties of Y 3 Al 5−x Ga x O 12 :Ce crystals on Ga content in x=0–3 and 3–5 ranges. • Elimination of the luminescence of Y Al antisite defects in Y 3 Al 5−x Ga x O 12 :Ce crystals at x>2. • Significant improvement of the scintillation properties of Y 3 Al 5−x Ga x O 12 :Ce crystals at x=2 and 3 in comparison with YAG:Ce

Performance of Mg-14Li-1Al-0.1Ce as anode for Mg-air battery

Energy Technology Data Exchange (ETDEWEB)

Ma, Yibin; Li, Deyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Li, Ning [School of Chemical Engineering and Technology, Harbin Institute of Technology, West Street No. 92, Harbin 150001 (China); Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China); Zhang, Milin; Huang, Xiaomei [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China)

2011-02-15

In this research, a new Mg-air battery based on Mg-14Li-1Al-0.1Ce was prepared and the battery performance was investigated by constant current discharge test. The corrosion behavior of Mg, AZ31 and Mg-Li-Al-Ce were studied by self-corrosion rate measurement and potentiodynamic polarization measurement. The characteristics of Mg-Li-Al-Ce after discharge were investigated by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results show that Mg-Li-Al-Ce is more active than Mg and AZ31. The self-corrosion rate is found to be in the order: Mg-Li-Al-Ce < Mg < AZ31. It has been observed that the Mg-air battery based on Mg-Li-Al-Ce offers higher operating voltage, anodic efficiency and capacity than those with Mg and AZ31. SEM and EIS results show that the discharge product of Mg-Li-Al-Ce is loosely adhered to the alloy surface, and thus Mg-Li-Al-Ce could keep high discharge activity during discharge. (author)

Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Wei; Zhang, Jinghuai; Li, Guoqiang; Feng, Yan; Su, Minliang; Wu, Ruizhi; Zhang, Zhongwu [Harbin Engineering Univ. (China). Key Laboratory of Superlight Material and Surface Technology; Jiao, Yufeng [Jiamusi Univ. (China). College of Materials Science and Engineering

2017-05-15

The thermal stability of Al-RE (rare earth) intermetallic phases with individual RE for heat-resistant high-pressure die-casting Mg-Al-RE alloys is investigated. The results of this study show that the main strengthening phase of Mg-4Al-4Ce alloy is Al{sub 11}Ce{sub 3}, whose content is about 5 wt.% according to quantitative X-ray diffraction phase analysis. The Al{sub 11}Ce{sub 3} phase appears to have high thermal stability at 200 C and 300 C, while phase morphology change with no phase structure transition could occur for Al{sub 11}Ce{sub 3} when the temperature reaches 400 C. Furthermore, besides the kinds of rare earths and temperature, stress is also an influencing factor in the microstructural stability of Mg-4Al-4Ce alloy.

Comparison of Efficiencies and Mechanisms of Catalytic Ozonation of Recalcitrant Petroleum Refinery Wastewater by Ce, Mg, and Ce-Mg Oxides Loaded Al2O3

Directory of Open Access Journals (Sweden)

Chunmao Chen

2017-02-01

Full Text Available The use of catalytic ozonation processes (COPs for the advanced treatment of recalcitrant petroleum refinery wastewater (RPRW is rapidly expanding. In this study, magnesium (Mg, cerium (Ce, and Mg-Ce oxide-loaded alumina (Al2O3 were developed as cost efficient catalysts for ozonation treatment of RPRW, having performance metrics that meet new discharge standards. Interactions between the metal oxides and the Al2O3 support influence the catalytic properties, as well as the efficiency and mechanism. Mg-Ce/Al2O3 (Mg-Ce/Al2O3-COP reduced the chemical oxygen demand by 4.7%, 4.1%, 6.0%, and 17.5% relative to Mg/Al2O3-COP, Ce/Al2O3-COP, Al2O3-COP, and single ozonation, respectively. The loaded composite metal oxides significantly increased the hydroxyl radical-mediated oxidation. Surface hydroxyl groups (–OHs are the dominant catalytic active sites on Al2O3. These active surface –OHs along with the deposited metal oxides (Mg2+ and/or Ce4+ increased the catalytic activity. The Mg-Ce/Al2O3 catalyst can be economically produced, has high efficiency, and is stable under acidic and alkaline conditions.

Effect of Al-5Ti-0.62C-0.2Ce Master Alloy on the Microstructure and Tensile Properties of Commercial Pure Al and Hypoeutectic Al-8Si Alloy

Directory of Open Access Journals (Sweden)

Wanwu Ding

2017-06-01

Full Text Available Al-5Ti-0.62C-0.2Ce master alloy was synthesized by a method of thermal explosion reaction in pure molten aluminum and used to modify commercial pure Al and hypoeutectic Al-8Si alloy. The microstructure and tensile properties of commercial pure Al and hypoeutectic Al-8Si alloy with different additions of Al-5Ti-0.62C-0.2Ce master alloy were investigated. The results show that the Al-5Ti-0.62C-0.2Ce alloy was composed of α-Al, granular TiC, lump-like TiAl3 and block-like Ti2Al20Ce. Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 5 min can significantly refine macro grains of commercial pure Al into tiny equiaxed grains. The Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 30 min still has a good refinement effect. The tensile strength and elongation of commercial pure Al modified by the Al-5Ti-0.62C-0.2Ce master alloy (0.3 wt %, 5 min increased by roughly 19.26% and 61.83%, respectively. Al-5Ti-0.62C-0.2Ce master alloy (1.5 wt %, 10 min can significantly refine both α-Al grains and eutectic Si of hypoeutectic Al-8Si alloy. The dendritic α-Al grains were significantly refined to tiny equiaxed grains. The morphology of the eutectic Si crystals was significantly refined from coarse needle-shape or lath-shape to short rod-like or grain-like eutectic Si. The tensile strength and elongation of hypoeutectic Al-8Si alloy modified by the Al-5Ti-0.62C-0.2Ce master alloy (1.5 wt %, 10 min increased by roughly 20.53% and 50%, respectively. The change in mechanical properties corresponds to evolution of the microstructure.

Comment on “Synthesis of ceria (CeO_2 and CeO_2_−_x) nanoparticles via decarbonation and Ce(III) oxidation of synthetic bastnaesite (CeCO_3F)” by Montes-Hernandez et al

International Nuclear Information System (INIS)

Gysi, Alexander P.; Williams-Jones, Anthony E.

2016-01-01

Montes-Hernandez et al. [5] recently reported results of a study of the decarbonation of fine-grained synthetic bastnäsite-(Ce) precipitates involving the oxidation of Ce(III) to Ce(IV) and the formation of ceria (CeO_2 and CeO_2_-_x with oxygen vacancies) nano-particles. The purpose of their study was to show that oxidation of Ce(III) to Ce(IV) occurs spontaneously during heating of bastnäsite-(Ce) in air, a vacuum, N_2 or Ar gas. However, their interpretation of the formation of CeO_2 is not supported by the findings of Gysi and Williams-Jones [3], who showed that natural bastnäsite-(Ce) decomposes to form rare earth element (REE) oxyfluorides (REEOF). The latter was documented using differential scanning calorimetric (DSC) and thermogravimetric (TGA) experiments under a deoxygenated N_2 atmosphere. In their experiments, Gysi and Williams-Jones [3] found no evidence for the oxidation of Ce(III) to Ce(IV). This raises the question of whether the experiments of Montes-Hernandez et al. [5] in a N_2 atmosphere (and by extension in an Ar atmosphere) were compromised because of contamination by O_2 and that, as a result, they reached the erroneous conclusion that Ce(III) oxidizes spontaneously to Ce(IV) during heating of bastnäsite-(Ce) under these conditions. In order to explain the disagreement between their findings and those of Gysi and Williams-Jones [3], Montes-Hernandez et al. [5], proposed that the X-ray diffraction data of the former study were incorrectly interpreted. Here, we provide further evidence that the natural bastnäsite-(Ce) employed in the study by Gysi and Williams-Jones [3] decomposed to form REE oxyfluorides (i.e., CeOF, LaOF, PrOF and NdOF) and not CeO_2, and supply explanations for why Montes-Hernandez et al. [5] erroneously concluded that CeO_2 is produced during decomposition of this mineral under N_2 and Ar atmospheres. In so doing, we hope to provide new insights into the decomposition of bastnäsite-(Ce) that will help guide future

Effect of CeLa addition on the microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy

International Nuclear Information System (INIS)

Du, Jiandi; Ding, Dongyan; Xu, Zhou; Zhang, Junchao; Zhang, Wenlong; Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua; Chen, Renzong; Huang, Yuanwei; Tang, Jinsong

2017-01-01

Development of high strength lithium battery shell alloy is highly desired for new energy automobile industry. The microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy with different CeLa additions were investigated through optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Rietveld refinement and tensile testing. Experimental results indicate that Al 8 Cu 4 Ce and Al 6 Cu 6 La phases formed due to CeLa addition. Addition of 0.25 wt.% CeLa could promote the formation of denser precipitation of Al 20 Cu 2 Mn 3 and Al 6 (Mn, Fe) phases, which improved the mechanical properties of the alloy at room temperature. However, up to 0.50 wt.% CeLa addition could promote the formation of coarse Al 8 Cu 4 Ce phase, Al 6 Cu 6 La phase and Al 6 (Mn, Fe) phase, which resulted in weakened mechanical properties. - Highlights: •Al-Cu-Mn-Mg-Fe alloys with different CeLa addition were fabricated through casting and rolling. •Al 8 Cu 4 Ce and Al 6 Cu 6 La phases formed after CeLa addition. •Addition of 0.25 wt.% CeLa promoted formation of denser precipitates of Al 20 Cu 2 Mn 3 and Al 6 (Mn, Fe). •Mechanical properties of the alloy was improved after 0.25 wt.% CeLa addition.

Magnetic domains and frustration in metallic CePdAl

Energy Technology Data Exchange (ETDEWEB)

Lucas, Stefan; Huesges, Zita; Huang, Chien-Lung; Stockert, Oliver [Max Planck Institute CPfS, Dresden (Germany); Fritsch, Veronika; Sakai, Akito [EP 6, Electronic Correlations and Magnetism, University of Augsburg (Germany); Grube, Kai; Taubenheim, Christian; Loehneysen, Hilbert von [Karlsruhe Institute of Technology (Germany)

2016-07-01

Magnetic frustration is an exciting topic in condensed matter physics, since it can lead to new ground states of materials, e.g. a spin liquid or spin glass state. Effects of magnetic frustration have been investigated intensively for insulating materials. However, the existence of magnetic frustration in metallic systems is still under debate. CePdAl is a metallic Kondo system, where geometric magnetic frustration arises from the formation of Ce ions on a distorted Kagome lattice. Neutron scattering experiments revealed, that only two thirds of the magnetic Ce moments order antiferromagnetically below T{sub N}=2.7 K, whereas the other third remains mainly disordered. Thermodynamic as well as neutron scattering measurements are presented to verify the existence of partial magnetic frustration in CePdAl. Recently neutron diffraction experiments under magnetic fields applied along two orthogonal directions in the magnetically hard basal plane were performed. They show opposite effects on the magnetic intensity of a selected magnetic domain depending on the field direction with respect to the propagation vector. If this is only an effect of different domain population or also due to a change in magnetic frustration shall be discussed.

Effect of CeLa addition on the microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy

Energy Technology Data Exchange (ETDEWEB)

Du, Jiandi [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Ding, Dongyan, E-mail: dyding@sjtu.edu.cn [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Xu, Zhou; Zhang, Junchao; Zhang, Wenlong [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua [Huafon NLM Al Co., Ltd, Shanghai 201506 (China); Chen, Renzong; Huang, Yuanwei; Tang, Jinsong [Shanghai Huafon Materials Technology Institute, Shanghai 201203 (China)

2017-01-15

Development of high strength lithium battery shell alloy is highly desired for new energy automobile industry. The microstructures and mechanical properties of Al-Cu-Mn-Mg-Fe alloy with different CeLa additions were investigated through optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Rietveld refinement and tensile testing. Experimental results indicate that Al{sub 8}Cu{sub 4}Ce and Al{sub 6}Cu{sub 6}La phases formed due to CeLa addition. Addition of 0.25 wt.% CeLa could promote the formation of denser precipitation of Al{sub 20}Cu{sub 2}Mn{sub 3} and Al{sub 6}(Mn, Fe) phases, which improved the mechanical properties of the alloy at room temperature. However, up to 0.50 wt.% CeLa addition could promote the formation of coarse Al{sub 8}Cu{sub 4}Ce phase, Al{sub 6}Cu{sub 6}La phase and Al{sub 6}(Mn, Fe) phase, which resulted in weakened mechanical properties. - Highlights: •Al-Cu-Mn-Mg-Fe alloys with different CeLa addition were fabricated through casting and rolling. •Al{sub 8}Cu{sub 4}Ce and Al{sub 6}Cu{sub 6}La phases formed after CeLa addition. •Addition of 0.25 wt.% CeLa promoted formation of denser precipitates of Al{sub 20}Cu{sub 2}Mn{sub 3} and Al{sub 6}(Mn, Fe). •Mechanical properties of the alloy was improved after 0.25 wt.% CeLa addition.

Tunable colorimetric performance of Al{sub 2}O{sub 3}-YAG:Ce{sup 3+} eutectic crystal by Ce{sup 3+} concentration

Energy Technology Data Exchange (ETDEWEB)

Sai, Qinglin, E-mail: saiql@siom.ac.cn; Xia, Changtai, E-mail: xia_ct@siom.ac.cn

2017-06-15

Ce-doped Al{sub 2}O{sub 3}-YAG eutectics with different percentage of Ce were successfully grown by the optical floating zone technique. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to investigate the structure. The results show that they have typical eutectic structure of interpenetrating sapphire and garnet phases with the tens of microns lamella spacing. The photoluminescence spectra of the eutectics showed that they have wide excitation band, and samples with 1.6 mol% Ce-doped has the highest emission intensity. The eutectic-packaged LED has high luminous efficiency and its color can be modulated by changing Ce concentration. The results reveal that Ce-doped Al{sub 2}O{sub 3}-YAG eutectic is a promising phosphor for white LED applications.

Teoría de la mente en un grupo de personas vinculadas al conflicto armado y en proceso de resocialización

Directory of Open Access Journals (Sweden)

Mónica Gómez

2013-12-01

Full Text Available La teoría de la mente es la capacidad de inferir, predecir y atribuir estados mentales a otras personas. Este constructo ha sido estudiado desde numerosas patologías, como el autismo, la esquizofrenia y el síndrome de down. Estudios recientes han mostrado que las alteraciones de la teoría de la mente pueden ser observadas en los diferentes cuadros clínicos derivados de alteraciones del lóbulo frontal, como la personalidad antisocial. Algunos autores plantean que un aspecto esencial de la teoría de la mente es la empatía. Sin embargo, este constructo no ha sido estudiado en población normal colombiana con conductas violentas y delictivas que han estado vinculadas al conflicto armado. Este artículo tiene como propósito describir algunas características de la tom en sujetos que estuvieron vinculados al conflicto armado en antioquia con manifestaciones sintomáticas relacionadas con comportamientos violentos y delictivos.

Geometrically frustrated magnetic structures of the heavy-fermion compound CePdAl studied by powder neutron diffraction

Energy Technology Data Exchange (ETDEWEB)

Doenni, A.; Fischer, P.; Zolliker, M. [Laboratory for Neutron Scattering, ETH Zuerich and Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Ehlers, G.; Maletta, H. [Hahn Meitner Institute Berlin, Glienicker Strasse 100, D-14092 Berlin (Germany); Kitazawa, H. [National Research Institute for Metals, Tsukuba, Ibaraki 305 (Japan)

1996-12-09

The heavy-fermion compound CePdAl with ZrNiAl-type crystal structure (hexagonal space group P6-bar2m) was investigated by powder neutron diffraction. The triangular coordination symmetry of magnetic Ce atoms on site 3f gives rise to geometrical frustration. CePdAl orders below T{sub N} = 2.7 K with an incommensurate antiferromagnetic propagation vector k=[1/2, 0, {tau}], {tau} approx. 0.35, and a longitudinal sine-wave (LSW) modulated spin arrangement. Magnetically ordered moments at Ce(1) and Ce(3) coexist with frustrated disordered moments at Ce(2). The experimentally determined magnetic structure is in agreement with group theoretical symmetry analysis considerations, calculated by the program MODY, which confirm that for Ce(2) an ordered magnetic moment parallel to the magnetically easy c-axis is forbidden by symmetry. Further low-temperature experiments give evidence for a second magnetic phase transition in CePdAl between 0.6 and 1.3 K. Magnetic structures of CePdAl are compared with those of the isostructural compound TbNiAl, where a non-zero ordered magnetic moment for the geometrically frustrated Tb(2) atoms is allowed by symmetry. (author)

Urea-assisted synthesis of AlPO4:Ce,Tb nanorods as a redox luminescence switch

International Nuclear Information System (INIS)

Yang, Wei; Hu, Juncheng

2013-01-01

AlPO 4 :Ce,Tb nanorods were synthesized by a facile hydrothermal method. The morphology of rod-like AlPO 4 was tuned by varying urea concentrations, AlPO 4 gradually changed from nanosheets to nanorods, and urea provided hydroxyl anion (OH − ) in the aqueous solution to prepare the dispersed nanorods under the hydrothermal conditions. The emission intensity of nanorods increased significantly compared to that of nanosheets. AlPO 4 :Ce,Tb nanorods provided a novel redox luminescence switch on the basis of the reversible switching of the Ce 3+ /Ce 4+ redox couple. The luminescence is quenched (off) when the system is in the oxidized form while it is restored (on) in the reduced form. The mechanism of the energy transfer and electronic transition between Ce 3+ and Tb 3+ in the AlPO 4 nanorods was also discussed. This switch has biocompatibility and low toxicity, and may have a potential application in biomedical diagnostics and analysis

Comment on “Synthesis of ceria (CeO{sub 2} and CeO{sub 2−x}) nanoparticles via decarbonation and Ce(III) oxidation of synthetic bastnaesite (CeCO{sub 3}F)” by Montes-Hernandez et al

Energy Technology Data Exchange (ETDEWEB)

Gysi, Alexander P., E-mail: agysi@mines.edu [Department of Geology and Geological Engineering, Colorado School of Mines, 1516 Illinois Street, Golden, CO, 80401 (United States); Williams-Jones, Anthony E. [Department of Earth and Planetary Sciences, McGill University, 3450 University Street, Montreal, QC, Canada, H3A 2A7 (Canada)

2016-11-01

Montes-Hernandez et al. [5] recently reported results of a study of the decarbonation of fine-grained synthetic bastnäsite-(Ce) precipitates involving the oxidation of Ce(III) to Ce(IV) and the formation of ceria (CeO{sub 2} and CeO{sub 2-x} with oxygen vacancies) nano-particles. The purpose of their study was to show that oxidation of Ce(III) to Ce(IV) occurs spontaneously during heating of bastnäsite-(Ce) in air, a vacuum, N{sub 2} or Ar gas. However, their interpretation of the formation of CeO{sub 2} is not supported by the findings of Gysi and Williams-Jones [3], who showed that natural bastnäsite-(Ce) decomposes to form rare earth element (REE) oxyfluorides (REEOF). The latter was documented using differential scanning calorimetric (DSC) and thermogravimetric (TGA) experiments under a deoxygenated N{sub 2} atmosphere. In their experiments, Gysi and Williams-Jones [3] found no evidence for the oxidation of Ce(III) to Ce(IV). This raises the question of whether the experiments of Montes-Hernandez et al. [5] in a N{sub 2} atmosphere (and by extension in an Ar atmosphere) were compromised because of contamination by O{sub 2} and that, as a result, they reached the erroneous conclusion that Ce(III) oxidizes spontaneously to Ce(IV) during heating of bastnäsite-(Ce) under these conditions. In order to explain the disagreement between their findings and those of Gysi and Williams-Jones [3], Montes-Hernandez et al. [5], proposed that the X-ray diffraction data of the former study were incorrectly interpreted. Here, we provide further evidence that the natural bastnäsite-(Ce) employed in the study by Gysi and Williams-Jones [3] decomposed to form REE oxyfluorides (i.e., CeOF, LaOF, PrOF and NdOF) and not CeO{sub 2}, and supply explanations for why Montes-Hernandez et al. [5] erroneously concluded that CeO{sub 2} is produced during decomposition of this mineral under N{sub 2} and Ar atmospheres. In so doing, we hope to provide new insights into the decomposition of

RRh2Al10 (R = Ce, Yb): New intermetallic compounds in the 1 : 2 : 10 stoichiometry series

Science.gov (United States)

Strydom, A. M.; Djoumessi, R. F.; Blinova, M.; Tursina, A.; Nesterenko, S.; Avzuragova, V.

2018-05-01

The orthorhombic, space group Cmcm YbFe2Al10 structure type series of compounds are known to form with practically the entire series of rare-earth elements R, but only with the three d - electron elements Fe, Ru, and Os. The Ce-derivatives in particular have been of much interest since the first reports of their highly unusual physical properties. Classified as Kondo insulators, CeRu2Al10 and CeOs2Al10 controversially order magnetically and with uncharacteristically high Néel temperatures of ≃ 28 K. CeFe2Al10 on the other hand shows pronounced semiconducting and Kondo features but remains paramagnetic. As part of our ongoing studies into the rich physics of this class of materials we have succeeded in synthesizing new members of the 1:2:10 stoichiometry involving the chemical element Rh for the first time. CeRh2Al10 is found to crystallize in the tetragonal system with space group I41 / amd . Yb Rh2Al10 on the other hand forms in the serial Cmcm orthorhombic structure type. We discuss important similarities between the two types. At 5.310 Å the shortest Ce-Ce distance is, likewise to the situation in CeRu2Al10 and CeOs2Al10 , also well above the Hill limit of 3.40 Å. Despite the cage-like structure and large rare-earth separation distances, this study reveals the onset of long-range magnetic ordering in CeRh2Al10 at 3.9 K. The magnetic ordering develops out of an incoherent Kondo state that dominates the electrical resistivity below about 40 K.

Low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy

Directory of Open Access Journals (Sweden)

Wu Wei

2013-11-01

Full Text Available Fatigue failure is a main failure mode for magnesium and other alloys. It is beneficial for fatigue design and fatigue life improvement to investigate the low cycle fatigue behavior of magnesium alloys. In order to investigate the low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy, the strain controlled fatigue experiments were performed at room temperature and fatigue fracture surfaces of specimens were observed with scanning election microscopy for the alloys under die-cast and aged states. Cyclic stress response curves, strain amplitude versus reversals to failure curve, total strain amplitude versus fatigue life curves and cyclic stress-strain curves of Mg-Al-Mn-Ce alloys were analyzed. The results show that the Mg-Al-Mn-Ce alloys under die-cast (F and aged (T5 states exhibit cyclic strain hardening under the applied total strain amplitudes, and aging treatment could greatly increase the cyclic stress amplitudes of die cast Mg-Al-Mn-Ce alloys. The relationships between the plastic strain amplitude, the elastic strain amplitude and reversals to failure of Mg-Al-Mn-Ce magnesium alloy under different treatment states could be described by Coffin-Manson and Basquin equations, respectively. Observations on the fatigue fracture surface of specimens reveal that the fatigue cracks initiate on the surface of specimens and propagate transgranularly.

Tunable Luminescence of CeAl11O18 Based Phosphors by Replacement of (AlO)+ by (SiN)+ and Co-Doping with Eu

NARCIS (Netherlands)

Yin, L.J.; Chen, G.Z; Wang, C.; Xu, X.; Hao, L.Y.; Hintzen, H.T.J.M.

2014-01-01

A series of Si-N or Eu-Li doped CeAl11O18 and CeAl12O18N phosphors are prepared by solid–state reaction. Their structure and luminescence are researched carefully. Si-N doping with the concentration less than 8% can be successfully dissolved into CeAl11O18 crystal lattice and doesn't change the

Electron traps and scintillation mechanism in YAlO3:Ce and LuAlO3:Ce scintillators

International Nuclear Information System (INIS)

Wojtowicz, A.J.; Glodo, J.; Drozdowski, W.; Przegietka, K.R.

1998-01-01

In this paper we present the results of thermoluminescence, isothermal decay and scintillation light yield measurements on two isostructural scintillator materials, YAlO 3 :Ce and LuAlO 3 :Ce. In addition to the variety of deep traps identified by thermoluminescence and isothermal decays, scintillation light yield experiments demonstrate the presence in both materials of a number of relatively shallow traps. While the deep traps may reduce the scintillation light yield, they do not influence the kinetics of the process. The shallow traps, on the other hand, by interfering with the process of radiative recombination of charge carriers via Ce 3+ ions, can strongly affect not only the yield of the scintillation process but its kinetics as well. The presence of shallow traps provides a consistent explanation for a number of poorly understood relationships between the two scintillator materials, including a higher room temperature scintillation light yield and longer scintillation decay time in YAlO 3 :Ce, and a longer scintillation rise time in LuAlO 3 :Ce. Theoretical analysis indicates that elimination of these traps would make the two materials nearly identical in scintillator performance. Although the specific identity of all traps remains elusive, the performance of both scintillator materials is now, in practical terms, fully understood. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

On the response of Y 3Al 5O 12: Ce (YAG: Ce) powder scintillating screens to medical imaging X-rays

Science.gov (United States)

Kandarakis, I.; Cavouras, D.; Sianoudis, I.; Nikolopoulos, D.; Episkopakis, A.; Linardatos, D.; Margetis, D.; Nirgianaki, E.; Roussou, M.; Melissaropoulos, P.; Kalivas, N.; Kalatzis, I.; Kourkoutas, K.; Dimitropoulos, N.; Louizi, A.; Nomicos, C.; Panayiotakis, G.

2005-02-01

The aim of this study was to examine Y 3Al 5O 12:Ce (also known as YAG:Ce) powder scintillator under X-ray imaging conditions. This material shows a very fast scintillation decay time and it has never been used in X-ray medical imaging. In the present study various scintillator layers (screens) with coating thickness ranging from 13 to 166 mg/cm 2 were prepared in our laboratory by sedimentation of Y 3Al 5O 12: Ce powder. Optical emission spectra and light emission efficiency (spectrum area over X-ray exposure) of the layers were measured under X-ray excitation using X-ray tube voltages (80-120 kVp) often employed in general medical radiography and fluoroscopy. Spectral compatibility with various optical photon detectors (photodiodes, photocathodes, charge coupled devices, films) and intrinsic conversion efficiency values were determined using emission spectrum data. In addition, parameters related to X-ray detection, energy absorption efficiency and K-fluorescence characteristic emission were calculated. A theoretical model describing radiation and light transfer through scattering media was used to fit experimental data. Intrinsic conversion efficiency (η≈0.03-0.05) and light attenuation coefficients (σ≈26.5 cm/g) were derived through this fitting. Y 3Al 5O 12:Ce showed peak emission in the wavelength range 530-550 nm. The light emission efficiency was found to be maximum for the 107 mg/cm 2 layer. Due to its "green" emission spectrum, Y 3Al 5O 12:Ce showed excellent compatibility (of the order of 0.9) with the sensitivity of many currently used photodetectors. Taking into account its very fast response Y 3Al 5O 12:Ce could be considered for application in X-ray imaging especially in various digital detectors.

On the response of Y3Al5O12: Ce (YAG: Ce) powder scintillating screens to medical imaging X-rays

International Nuclear Information System (INIS)

Kandarakis, I.; Cavouras, D.; Sianoudis, I.; Nikolopoulos, D.; Episkopakis, A.; Linardatos, D.; Margetis, D.; Nirgianaki, E.; Roussou, M.; Melissaropoulos, P.; Kalivas, N.; Kalatzis, I.; Kourkoutas, K.; Dimitropoulos, N.; Louizi, A.; Nomicos, C.; Panayiotakis, G.

2005-01-01

The aim of this study was to examine Y 3 Al 5 O 12 :Ce (also known as YAG:Ce) powder scintillator under X-ray imaging conditions. This material shows a very fast scintillation decay time and it has never been used in X-ray medical imaging. In the present study various scintillator layers (screens) with coating thickness ranging from 13 to 166mg/cm 2 were prepared in our laboratory by sedimentation of Y 3 Al 5 O 12 : Ce powder. Optical emission spectra and light emission efficiency (spectrum area over X-ray exposure) of the layers were measured under X-ray excitation using X-ray tube voltages (80-120kVp) often employed in general medical radiography and fluoroscopy. Spectral compatibility with various optical photon detectors (photodiodes, photocathodes, charge coupled devices, films) and intrinsic conversion efficiency values were determined using emission spectrum data. In addition, parameters related to X-ray detection, energy absorption efficiency and K-fluorescence characteristic emission were calculated. A theoretical model describing radiation and light transfer through scattering media was used to fit experimental data. Intrinsic conversion efficiency (ηC ∼0.03-0.05) and light attenuation coefficients (σ∼26.5cm 2 /g) were derived through this fitting. Y 3 Al 5 O 12 :Ce showed peak emission in the wavelength range 530-550nm. The light emission efficiency was found to be maximum for the 107mg/cm 2 layer. Due to its 'green' emission spectrum, Y 3 Al 5 O 12 :Ce showed excellent compatibility (of the order of 0.9) with the sensitivity of many currently used photodetectors. Taking into account its very fast response Y 3 Al 5 O 12 :Ce could be considered for application in X-ray imaging especially in various digital detectors

Confined NaAlH4 nanoparticles inside CeO2 hollow nanotubes towards enhanced hydrogen storage.

Science.gov (United States)

Gao, Qili; Xia, Guanglin; Yu, Xuebin

2017-10-05

NaAlH 4 has been widely regarded as a potential hydrogen storage material due to its favorable thermodynamics and high energy density. The high activation energy barrier and high dehydrogenation temperature, however, significantly hinder its practical application. In this paper, CeO 2 hollow nanotubes (HNTs) prepared by a simple electrospinning technique are adopted as functional scaffolds to support NaAlH 4 nanoparticles (NPs) towards advanced hydrogen storage performance. The nanoconfined NaAlH 4 inside CeO 2 HNTs, synthesized via the infiltration of molten NaAlH 4 into the CeO 2 HNTs under high hydrogen pressure, exhibited significantly improved dehydrogenation properties compared with both bulk and ball-milled CeO 2 HNTs-catalyzed NaAlH 4 . The onset dehydrogenation temperature of the NaAlH 4 @CeO 2 composite was reduced to below 100 °C, with only one main dehydrogenation peak appearing at 130 °C, which is 120 °C and 50 °C lower than for its bulk counterpart and for the ball-milled CeO 2 HNTs-catalyzed NaAlH 4 , respectively. Moreover, ∼5.09 wt% hydrogen could be released within 30 min at 180 °C, while only 1.6 wt% hydrogen was desorbed from the ball-milled NaAlH 4 under the same conditions. This significant improvement is mainly attributed to the synergistic effects contributed by the CeO 2 HNTs, which could act as not only a structural scaffold to fabricate and confine the NaAlH 4 NPs, but also as an effective catalyst to enhance the hydrogen storage performance of NaAlH 4 .

Effects of A1 substitution by Fe in CeAl2

International Nuclear Information System (INIS)

Takeuchi, A.Y.; Cunha, S.F. da.

1989-01-01

Magnetization and electrical resistivity measurements of the CeAl 2 with Al substitution by Fe up to 10% at Fe show that the competition between the increasing Kondo effect and the antiferromagnetism persists. Change of the electronic density is followed by a decreasing Neel temperature and an increasing residual electrical reistivity. The probable appearance of ferromagnetism of the Ce moments, at intermediate temperature range, is discussed. The small decrease of the lattice parameter with Fe concentration or the magnetic behaviour do not show evidence of valence changes in the Ceion. (author) [pt

Crystal structure and physical properties of CePt{sub 2.4}Al{sub 0.6}

Energy Technology Data Exchange (ETDEWEB)

Provino, A., E-mail: alessia.sting@gmail.com [Department of Chemistry, University of Genova, Via Dodecaneso 31, 16146 Genova (Italy); Institute SPIN-CNR, Corso Perrone 24, 16152 Genova (Italy); Bhattacharyya, A. [Department of Condensed Matter Physics and Materials Science, Tata Institute of Fundamental Research, Colaba, Mumbai 400005 (India); Science and Technology Facilities Council, Rutherford Appleton Laboratory, Excitations and Polarized Neutrons Group, Harwell Oxford, Didcot OX11 0QX (United Kingdom); Negretti, L. [Department of Chemistry, University of Genova, Via Dodecaneso 31, 16146 Genova (Italy); Kulkarni, R.; Thamizhavel, A.; Dhar, S.K. [Department of Condensed Matter Physics and Materials Science, Tata Institute of Fundamental Research, Colaba, Mumbai 400005 (India)

2015-02-15

Highlights: • New CePt{sub 2.4}Al{sub 0.6} compound crystallizes in the hexagonal CeNi{sub 3}-type (hP24, P6{sub 3}/mmc). • This crystal structure is a nearly ordered ternary derivative of CeNi{sub 3} prototype. • CePt{sub 2.4}Al{sub 0.6} compound orders ferromagnetically at 1.6 K; Ce ions in trivalent state. • Magnetization, electrical resistivity, low-T heat capacity have been measured. • Negative magnetoresistivity below ∼15 K shows short-range FM in paramagnetic state. - Abstract: The new compound CePt{sub 2.4}Al{sub 0.6} crystallizes in the hexagonal CeNi{sub 3}-type (hP24, space group P6{sub 3}/mmc, N. 194), with lattice parameters a = 5.5203(3) Å and c = 16.886(1) Å; its crystal structure represents a nearly ordered ternary derivative of this prototype. The cerium ions in CePt{sub 2.4}Al{sub 0.6} are in the normal trivalent state and order magnetically near 1.6 K as inferred from the low temperature heat capacity. The magnetic ordering is presumably ferromagnetic as suggested by the behavior of heat capacity in applied magnetic fields. The magnetoresistivity below ∼15 K is negative and is tentatively attributed to the presence of ferromagnetic short range order in the paramagnetic state.

Thermoluminescence studies of γ-irradiated Al{sub 2}O{sub 3}:Ce{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Reddy, S. Satyanarayana [Physics R & D Center, PES Institute of Technology, BSK 3rd Stage, Bangalore 560085 (India); Nagabhushana, K.R., E-mail: bhushankr@gmail.com [Physics R & D Center, PES Institute of Technology, BSK 3rd Stage, Bangalore 560085 (India); Department of Physics, PES University, BSK 3rd Stage, Bangalore 560085 (India); Singh, Fouran [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110 067 (India)

2016-07-15

Pure and Ce{sup 3+} doped Al{sub 2}O{sub 3} phosphors were synthesized by solution combustion method. The synthesized samples were characterized by X-ray diffraction (XRD) and its shows α-phase of Al{sub 2}O{sub 3}. Crystallite size was estimated by Williamson–Hall (W–H) method and found to be 49, 59 and 84 nm for pure, 0.1 mol% and 1 mol% Ce{sup 3+} doped Al{sub 2}O{sub 3} respectively. Trace elemental analysis of undoped Al{sub 2}O{sub 3} shows impurities viz. Fe, Cr, Mn, Mg, Ti, etc. Photoluminescence (PL) spectra of Al{sub 2}O{sub 3}:Ce{sup 3+} shows emission at 367 nm and excitation peak at 273 nm, which are corresponding to {sup 5}D → {sup 4}F and {sup 4}F → {sup 5}D transitions respectively. PL intensity decreases with concentration up to 0.4 mol%, beyond this mol% PL intensity increases with doping concentration up to 2 mol%. Thermoluminescence (TL) studies of γ-rayed pure and Ce{sup 3+} doped Al{sub 2}O{sub 3} have been studied. Two well resolved TL glow peaks at 457.5 K and 622 K were observed in pure Al{sub 2}O{sub 3}. Additional glow peak at 566 K was observed in Al{sub 2}O{sub 3}:Ce{sup 3+}. Maximum TL intensity was observed for Al{sub 2}O{sub 3}:Ce{sup 3+} (0.1 mol%) beyond this TL intensity decreases with increasing Ce{sup 3+} concentration. Computerized glow curve deconvolution (CGCD) method was used to resolve the multiple peaks and to calculate TL kinetic parameters. Thermoluminescence emission (TLE) spectra of pure Al{sub 2}O{sub 3} glow peaks (457.5 K and 622 K) shows sharp emission at 694 nm and two small humps at 672 nm and 709 nm. The sharp peak at 696 nm corresponds to Cr{sup 3+} impurity of {sup 2}E{sub g} → {sup 4}A{sub 2g} transition of R lines and 713 nm hump is undoubtedly belongs to Cr{sup 3+} emission of near neighbor pairs. The emission at 672 nm is characteristic of Mn{sup 4+} impurity ions of {sup 2}E → {sup 4}A{sub 2} transition. TLE of Al{sub 2}O{sub 3}:Ce{sup 3+} (0.1 mol%) shows additional broad emission at 412 nm

Effect of Ce on Casting Structure of Near-rapidly Solidified Al-Zn-Mg-Cu Alloy

Directory of Open Access Journals (Sweden)

HUANG Gao-ren

2017-11-01

Full Text Available Through using XRD,DSC,SEM,EDS and other modern analysis methods, the effects of rare earth element Ce on microstructure and solidification temperature of Al-Zn-Mg-Cu under different cooling rates were studied, the principle of Ce on grain refining and melt cleaning of alloys was analyzed and discussed. The results show that MgZn2 phase and α-Al matrix are the main precipitations, Al,Cu,Mg and other elements dissolve in MgZn2 phase, a new phase Mg(Zn, Cu, Al2 is formed, solute elements in the grain boundary have higher concentration, eutectic reaction takes place between MgZn2 and α-Al, lamellar eutectic structure is generated. The addition of Ce decreases the dendritic arm spacing,reduces the layer spacing between eutectic phases and refines the eutectic structure and the grain significantly, and inhibits the appearance of the impurity phase Al7Cu2Fe in aluminum alloys. The addition of Ce also reduces the precipitation temperature of α-Al matrix and eutectic phase by 6.4℃ and 5.6℃ respectively.

Catalytic Oxidation of Propene over Pd Catalysts Supported on CeO2, TiO2, Al2O3 and M/Al2O3 Oxides (M = Ce, Ti, Fe, Mn

Directory of Open Access Journals (Sweden)

Sonia Gil

2015-04-01

Full Text Available In the following work, the catalytic behavior of Pd catalysts prepared using different oxides as support (Al2O3, CeO2 and TiO2 in the catalytic combustion of propene, in low concentration in excess of oxygen, to mimic the conditions of catalytic decomposition of a volatile organic compound of hydrocarbon-type is reported. In addition, the influence of different promoters (Ce, Ti, Fe and Mn when added to a Pd/Al2O3 catalyst was analyzed. Catalysts were prepared by the impregnation method and were characterized by ICP-OES, N2 adsorption, temperature-programmed reduction, temperature-programmed oxidation, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. Catalyst prepared using CeO2 as the support was less easily reducible, due to the stabilization effect of CeO2 over the palladium oxides. Small PdO particles and, therefore, high Pd dispersion were observed for all of the catalysts, as confirmed by XRD and TEM. The addition of Ce to the Pd/Al2O3 catalysts increased the metal-support interaction and the formation of highly-dispersed Pd species. The addition of Ce and Fe improved the catalytic behavior of the Pd/Al2O3 catalyst; however, the addition of Mn and Ti decreased the catalytic activity in the propene oxidation. Pd/TiO2 showed the highest catalytic activity, probably due to the high capacity of this catalyst to reoxidize Pd into PdO, as has been found in the temperature-programmed oxidation (TPO experiments.

RBS characterization of Al2O3 films doped with Ce and Mn

International Nuclear Information System (INIS)

Martinez-Martinez, R.; Rickards, J.; Garcia-Hipolito, M.; Trejo-Luna, R.; Martinez-Sanchez, E.; Alvarez-Fregoso, O.; Ramos-Brito, F.; Falcony, C.

2005-01-01

Rutherford backscattering (RBS) with 4 He energies from 2 to 6 MeV has been used to study the properties of thin amorphous photoluminescent Al 2 O 3 :Ce,Mn films grown by spray pyrolysis on Corning 7059 glass substrates. The source solutions were AlCl 3 , CeCl 3 and MnCl 2 dissolved in deionized water. Different molar concentrations (Ce 10%; Mn 1%, 3%, 5%, 7% and 10%) were investigated under the same deposition conditions at a substrate temperature of 300 deg. C. The RBS spectra show a homogeneous depth profile of both Ce and Mn within the films, and the measured quantities are consistent with the original solution concentrations. An important amount of Cl, which plays a significant role in luminescent properties, was detected, in both the doped and undoped samples

Formation of metastable cubic phase in Ce{sub 100−x}Al{sub x} (x=45, 50) alloys and their thermal and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Idzikowski, Bogdan, E-mail: idzi@ifmpan.poznan.pl [Institute of Molecular Physics, Polish Academy of Sciences, M. Smoluchowskiego 17, 60-179 Poznań (Poland); Centre for Advanced Materials and Smart Structures, Polish Academy of Sciences, Okólna 2, 50-422 Wrocław (Poland); Śniadecki, Zbigniew [Institute of Molecular Physics, Polish Academy of Sciences, M. Smoluchowskiego 17, 60-179 Poznań (Poland); Centre for Advanced Materials and Smart Structures, Polish Academy of Sciences, Okólna 2, 50-422 Wrocław (Poland); Puźniak, Roman [Institute of Physics, Polish Academy of Sciences, Aleja Lotników 32/46, 02-668 Warszawa (Poland); Kaczorowski, Dariusz [Institute of Low Temperature and Structure Research, Polish Academy of Sciences, P.O. Box 1410, 50-950 Wrocław (Poland); Centre for Advanced Materials and Smart Structures, Polish Academy of Sciences, Okólna 2, 50-422 Wrocław (Poland)

2017-01-01

Ce{sub 100−x}Al{sub x} (x=45 and 50) alloys were synthesized by rapid quenching technique in the form of ribbons composed of nanocrystalline phase of CeAl with the ClCs-type structure (Pm-3m space group) embedded in an amorphous matrix. The cubic CeAl phase is known as metastable with random distribution of Ce and Al atoms in the unit cell. The crystalline volume fraction is about 7.5% in Ce{sub 55}Al{sub 45} and 3% in Ce{sub 50}Al{sub 50}. The alloy Ce{sub 55}Al{sub 45} shows better thermal stability than Ce{sub 50}Al{sub 50}, indicated by higher effective activation energy and higher crystallization temperature. Small off-stoichiometry in Ce{sub 55}Al{sub 45} results in degrading the glass forming ability and promotes formation of the cubic CeAl phase, as confirmed by magnetic measurements. In both alloys, the Ce ions are in stable trivalent state and order magnetically near 20 K. Another magnetic phase transition close to 10 K was found for Ce{sub 50}Al{sub 50} and was attributed to the presence of the well-known stable orthorhombic CeAl phase. To the best of our knowledge, the magnetic behavior of the CeAl cubic phase is reported here for the first time. - Highlights: • Synthesis of metastable cubic CeAl phase by rapid quenching. • The Ce ions in Ce{sub 55}Al{sub 45} and Ce{sub 50}Al{sub 50} are in stable trivalent state. • Magnetic transition near 10 K connected with the orthorhombic CeAl phase. • Phase transition at about 20 K originates from the cubic CeAl phase.

In situ corrosion analysis of Al-Zn-In-Mg-Ti-Ce sacrificial anode alloy

International Nuclear Information System (INIS)

Ma Jingling; Wen Jiuba; Zhai Wenxia; Li Quanan

2012-01-01

The corrosion behaviour of Al-5Zn-0.02In-1Mg-0.05Ti-0.5Ce (wt.%) alloy has been investigated by immersion test, scanning electron microscopy, energy dispersive X-ray detector, electrochemical impedance spectroscopy and electrochemical noise. The results show that there exist different corrosion types of the alloy in 3.5% NaCl solution with the immersion time. At the initial stage of immersion, pitting due to the precipitates predominates the corrosion with a typical inductive loop at low frequencies in electrochemical impedance spectroscopy. The major precipitates of the alloy are MgZn 2 and Al 2 CeZn 2 particles. The corrosion potentials of the bulk MgZn 2 and Al 2 CeZn 2 alloys are negative with respect to that of α-Al, so the MgZn 2 and Al 2 CeZn 2 precipitates can act as activation centre and cause the pitting. In the late corrosion, a relative uniform corrosion predominates the corrosion process controlled by the dissolution/precipitation of the In ions and characterized by a capacitive loop at medium-high frequencies in electrochemical impedance spectroscopy. The potential noise of the pitting shows larger amplitude fluctuation and lower frequency, but the potential noise of the uniform corrosion occurs with smaller amplitude fluctuation and higher frequency.

Ca2 Al2 SiO7 :Ce3+ phosphors for mechanoluminescence dosimetry.

Science.gov (United States)

Tiwari, Geetanjali; Brahme, Nameeta; Sharma, Ravi; Bisen, D P; Sao, Sanjay Kumar; Sahu, Ishwar Prasad

2016-12-01

A series of Ce 3+ ion single-doped Ca 2 Al 2 SiO 7 phosphors was synthesized by a combustion-assisted method at an initiating temperature of 600 °C. The samples were annealed at 1100 °C for 3 h and their X-ray diffraction patterns confirmed a tetragonal structure. The phase structure, particle size, surface morphology and elemental analysis were analyzed using X-ray diffraction (XRD), transmission electron microscope (TEM), scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) spectroscopy techniques. Thermoluminescence (TL) intensity increased with increase in ultraviolet (UV) light exposure time up to 15 min. With further increase in the UV irradiation time the TL intensity decreases. The increase in TL intensity indicates that trap concentration increased with UV exposure time. A broad peak at 121 °C suggested the existence of a trapping level. The peak of mechanoluminescence (ML) intensity versus time curve increased linearly with increasing impact velocity of the moving piston. Mechanoluminescence intensity increased with increase in UV irradiation time up to 15 min. Under UV-irradiation excitation, the TL and ML emission spectra of Ca 2 Al 2 SiO 7 :Ce 3+ phosphor showed the characteristic emission of Ce 3+ peaking at 400 nm (UV-violet) and originating from the Ce 3+ transitions of 5d-4f ( 2 F 5/2 and 2 F 7/2 ). The photoluminescence (PL) emission spectra for Ca 2 Al 2 SiO 7 :Ce 3+ were similar to the ML/TL emission spectra. The mechanism of ML excitation and the suitability of the Ca 2 Al 2 SiO 7 :Ce 3+ phosphor for radiation dosimetry are discussed. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Neutron diffraction on CeMnAlD{sub x} (0{<=}x{<=}2.5)

Energy Technology Data Exchange (ETDEWEB)

Spatz, P.; Gross, K.; Schlapbach, L. [Fribourg Univ. (Switzerland); Fischer, P.; Fauth, F. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-09-01

CeMnAl was found to absorb considerable amounts of hydrogen. Part of the totally stored hydrogen is absorbed at low pressures (< 10 mbar). Additional hydrogen can be absorbed and desorbed reversible in a wide pressure range (10 mbar to 10 bar) at room temperature. In order to a better understanding of this new metal-hydride system, we performed neutron diffraction on deuterated CeMnAl samples with different D-concentrations. (author) 1 fig., 2 refs.

Study on fast luminescence component induced by gamma-rays in Ce doped LiCaAlF6 scintillators

International Nuclear Information System (INIS)

Watanabe, Kenichi; Kondo, Yoshiyuki; Yamazaki, Atsushi; Uritani, Akira; Iguchi, Tetsuo; Kawaguchi, Noriaki; Fukuda, Kentaro; Ishizu, Sumito; Yanagida, Takayuki; Fujimoto, Yutaka; Yoshikawa, Akira

2014-01-01

We discuss the origin of the fast luminescence component induced by fast electrons generated in gamma-ray interactions in Ce doped LiCaAlF 6 scintillators. Although the slow luminescence component induced by Ce 3+ emissions depends on the Ce concentration in the LiCaAlF 6 scintillator, the fast component is independent. The fast component is suggested to be generated in the host matrix of the LiCaAlF 6 crystal. From quantitative considerations based on Frank–Tamm equation, which shows the light yield of the Cherenkov radiation, the Cherenkov radiation was determined as the origin of the fast component. We, additionally, found that the slow rise time of main Ce 3+ emissions in the Ce:LiCaAlF 6 scintillator plays an important role to perform the pulse shape discrimination. - Highlights: • The fast luminescence in Ce:LiCaAlF 6 scintillator is generated in the host matrix. • The origin of the fast luminescence is determined as the Cherenkov radiation. • The slow rise time also plays an important role to perform PSD

Ultrafine Nanocrystalline CeO2@C-Containing NaAlH4 with Fast Kinetics and Good Reversibility for Hydrogen Storage.

Science.gov (United States)

Zhang, Xin; Liu, Yongfeng; Wang, Ke; Li, You; Gao, Mingxia; Pan, Hongge

2015-12-21

A nanocrystalline CeO2@C-containing NaAlH4 composite is successfully synthesized in situ by hydrogenating a NaH-Al mixture doped with CeO2@C. Compared with NaAlH4 , the as-prepared CeO2@C-containing NaAlH4 composite, with a minor amount of excess Al, exhibits significantly improved hydrogen storage properties. The dehydrogenation onset temperature of the hydrogenated [NaH-Al-7 wt % CeO2@C]-0.04Al sample is 77 °C lower than that of the pristine sample because of a reduced kinetic barrier. More importantly, the dehydrogenated sample absorbs ∼4.7 wt % hydrogen within 35 min at 100°C and 10 MPa of hydrogen. Compositional and structural analyses reveal that CeO2 is converted to CeH2 during ball milling and that the newly formed CeH2 works with the excess of Al to synergistically improve the hydrogen storage properties of NaAlH4. Our findings will aid in the rational design of novel catalyst-doped complex hydride systems with low operating temperatures, fast kinetics, and long-term cyclability. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Neutron diffraction study of dense-Kondo compound CeNi2Al5

International Nuclear Information System (INIS)

Munoz, A.; Givord, F.; Boucherie, J.X.; Flouquet, J.; Isikawa, Y.; Mizushima, T.; Sakurai, J.; Mori, K.; Oliveira, I.S.

1993-01-01

Intermetallic CeNi 2 Al 5 is a dense-Kondo compound with a magnetic transition temperature at 2.6 K. We have carried out a neutron diffraction measurement to study a magnetic structure of CeNi 2 Al 5 using a powder sample and a single crystalline sample. It is found that the magnetic structure is an incommensurate sinusoidal one with a propagation vector k = (0.5, 0.405, 0.083) and that the amplitude of magnetic moment is 1.54 μ Β and the direction of magnetic moment is declined 8 deg. from the b-axis toward the a-axis. (authors). 3 refs., 2 figs

Luminescent properties of Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce crystals

Energy Technology Data Exchange (ETDEWEB)

Zorenko, Yu., E-mail: zorenko@ukw.edu.pl [Institute of Physics, Kazimierz Wielki University in Bydgoszcz, Powstańców Wielkopolskich No 2, 85-090 Bydgoszcz (Poland); Zorenko, T. [Institute of Physics, Kazimierz Wielki University in Bydgoszcz, Powstańców Wielkopolskich No 2, 85-090 Bydgoszcz (Poland); Department of Electronics, Ivan Franko National University of Lviv, Gen. Tarnavskyj str. 107, 70017 Lviv (Ukraine); Malinowski, P. [Institute of Physics, Kazimierz Wielki University in Bydgoszcz, Powstańców Wielkopolskich No 2, 85-090 Bydgoszcz (Poland); Sidletskiy, O.; Neicheva, S. [Institute for Scintillation Materials, National Academy of Sciences of Ukraine, Lenina pr. 60, 61001 Kharkiv (Ukraine)

2014-12-15

Absorption, luminescent and scintillation properties of Ce{sup 3+} doped Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12} crystals with Ga content in the x=1–5 range were investigated in this work and compared with the properties of YAG:Ce crystals. Apart from the traditional spectral methods (absorption, cathodoluminescence and light yield measurements), the intrinsic and Ce{sup 3+} related luminescence of Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce solid-solution were also investigated using the luminescent spectroscopy under excitation by synchrotron radiation in the 3.7–25 eV range. We show that the optical properties Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce garnets monotonically change with increasing the Ga content in the x=0–3 range due to preferable localization of Ga ions in the tetrahedral position of the garnet lattice. At the highest Ga concentration (x>3) the deviation of the optical properties of Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce garnets is observed from the respective properties of these crystals with Ga content in the x=0–3 range due to occupation by Ga ions of the octahedral position in the garnet host. - Highlights: • Different dependence of optical properties of Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce crystals on Ga content in x=0–3 and 3–5 ranges. • Elimination of the luminescence of Y{sub Al} antisite defects in Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce crystals at x>2. • Significant improvement of the scintillation properties of Y{sub 3}Al{sub 5−x}Ga{sub x}O{sub 12}:Ce crystals at x=2 and 3 in comparison with YAG:Ce.

Modification and aging precipitation behavior of hypereutectic Al-21wt.%Si alloy treated by P+Ce combination

Directory of Open Access Journals (Sweden)

Liu Pei

2014-11-01

Full Text Available In the present study, the tested hypereutectic Al-21wt.%Si alloys were prepared by modifying the melt using different proportions of P and Ce, and then applying T6 heat treatment. The modification effects and mechanism of P+Ce complex modifier on the Si phase of hypereutectic Al-21wt.%Si alloy were studied, and the aging precipitation behavior after modification was characterized by means of tensile strength measurement, OM, SEM and TEM analysis. The results show that the massive primary silicon phase particles are significantly refined after modification, while the needle-like eutectic silicon crystals become fibrous and short. It was found that the mechanism of phosphorus modification on the primary silicon can be attributed to heterogeneous nucleation of AlP, while the modification mechanism of Ce can be explained by adsorbing-twinning theory. In the aged microstructure of the modified hypereutectic Al-21wt.%Si alloy, there existed some strengthening phases such as Al4Cu9, Al2Cu, AlCu3, and Al57Mn12. The P+Ce complex modifier not only affected the size of primary silicon and eutectic silicon, but also the aging behavior of alloys under the heat treatment process. When Al-21wt.%Si alloy was modified using 0.08%wt.P + 0.6wt.% Ce, the aging precipitates were dispersed uniformly in the alloy, and its mechanical properties at room and elevated temperatures are optimized (Rm = 287.6 MPa at RT, Rm = 210 MPa at 300 ℃.

Generation and reactivity of putative support systems, Ce-Al neutral binary oxide nanoclusters: CO oxidation and C-H bond activation

Science.gov (United States)

Wang, Zhe-Chen; Yin, Shi; Bernstein, Elliot R.

2013-11-01

Both ceria (CeO2) and alumina (Al2O3) are very important catalyst support materials. Neutral binary oxide nanoclusters (NBONCs), CexAlyOz, are generated and detected in the gas phase and their reactivity with carbon monoxide (CO) and butane (C4H10) is studied. The very active species CeAlO4• can react with CO and butane via O atom transfer (OAT) and H atom transfer (HAT), respectively. Other CexAlyOz NBONCs do not show reactivities toward CO and C4H10. The structures, as well as the reactivities, of CexAlyOz NBONCs are studied theoretically employing density functional theory (DFT) calculations. The ground state CeAlO4• NBONC possesses a kite-shaped structure with an OtCeObObAlOt configuration (Ot, terminal oxygen; Ob, bridging oxygen). An unpaired electron is localized on the Ot atom of the AlOt moiety rather than the CeOt moiety: this Ot centered radical moiety plays a very important role for the reactivity of the CeAlO4• NBONC. The reactivities of Ce2O4, CeAlO4•, and Al2O4 toward CO are compared, emphasizing the importance of a spin-localized terminal oxygen for these reactions. Intramolecular charge distributions do not appear to play a role in the reactivities of these neutral clusters, but could be important for charged isoelectronic BONCs. DFT studies show that the reaction of CeAlO4• with C4H10 to form the CeAlO4H•C4H9• encounter complex is barrierless. While HAT processes have been previously characterized for cationic and anionic oxide clusters, the reported study is the first observation of a HAT process supported by a ground state neutral oxide cluster. Mechanisms for catalytic oxidation of CO over surfaces of AlxOy/MmOn or MmOn/AlxOy materials are proposed consistent with the presented experimental and theoretical results.

Effects of Ce Addition and Isothermal Aging on the Elevated Temperature Tensile Properties of Mechanically Alloyed Al-Ti Alloys

Energy Technology Data Exchange (ETDEWEB)

Kim, JunKi; Oh, YoungMin; Kim, YongDeog; Kim, SeonJin [Hanyang Univ., Seoul (Korea, Republic of); Kim, ByungChul [KOREA ATOMIC RESEARCH INSTITUTE, TAEJON (Korea, Republic of)

1997-05-01

The room and elevated temperature tensile strength of mechanically alloyed Al-8wt%. Ti alloy increased by substituting Ce for Ti up to 25at.%. However, further substitution of Ce for Ti decreased the tensile strength. It was considered to be due to the decrease of volume fraction of Ce contained dispersoid. In the meantime, the decrease of tensile strength due to the isothermal aging was effectively reduced by the addition of Ce at 400 deg. C but not 510 deg. C. The activation energies for the deformation of Al-80wt.%(Ti+Ce)alloys measured at the temperature between 300 deg. C{approx}510 deg. C were about 1.3{approx}1.9 times higher than that for pure Al self-diffusion(142 kJ/mole). Thus, it was considered that the elevated temperature deformation of Al-8wt.%(Ti+Ce)alloys was governed by Orowan mechanism (author). 9 refs. 6 figs.

Estructura Organizacional de las Empresas Vinculadas a la Incubadora de Base Tecnológica de la Universidad de Fortaleza: Un Análisis Bajo la Perspectiva de Mintzberg.

Directory of Open Access Journals (Sweden)

Sarah Mesquita Lima

2014-09-01

Full Text Available El presente estudio tiene el objetivo principal de analizar si la configuración estructural predominante de las empresas asociadas a la Incubadora de Base Tecnológica de la Universidad de Fortaleza está vinculada a sus competencias. Para alcanzar el objetivo propuesto se realizó una investigación descriptiva y cualitativa, con estudio de múltiples casos. Los datos fueron recolectados mediante el análisis de documentos, entrevista con el coordinador del Espacio de Desarrollo de Empresas de Tecnología (EDETEC de la UNIFOR y aplicación de cuestionarios auto-administrados en las empresas vinculadas al EDETEC/UNIFOR. Los resultados indicaron el predominio de las configuraciones Burocracia Profesional, Estructura Simple y Adhocracia, estando estas dos últimas directamente vinculadas a las competencias emprendedoras e innovadoras.

Ordered Mesoporous NiCeAl Containing Catalysts for Hydrogenolysis of Sorbitol to Glycols

Science.gov (United States)

Zhou, Zhiwei; Zhang, Jiaqi; Qin, Juan; Li, Dong; Wu, Wenliang

2018-03-01

Cellulose-derived sorbitol is emerging as a feasible and renewable feedstock for the production of value-added chemicals. Highly active and stable catalyst is essential for sorbitol hydrogenolysis. Ordered mesoporous M- xNi yCeAl catalysts with different loadings of nickel and cerium species were successfully synthesized via one-pot evaporation-induced self-assembly strategy (EISA) and their catalytic performance were tested in the hydrogenolysis of sorbitol. The physical chemical properties for the catalysts were characterized by XRD, N2 physisorption, H2-TPR, H2 impulse chemisorption, ICP and TEM techniques. The results showed that the ordered mesopores with uniform pore sizes can be obtained and the Ni nanoparticles around 6 nm in size were homogeneously dispersed in the mesopore channels. A little amount of cerium species introduced would be beneficial to their textural properties resulting in higher Ni dispersion, metal area and smaller size of Ni nanoparticles. The M-10Ni2CeAl catalyst with Ni and Ce loading of 10.9 and 6.3 wt % shows better catalytic performance than other catalysts, and the yield of 1,2-PG and EG can reach 56.9% at 493 K and 6 MPa pressure for 8 h after repeating reactions for 12 times without obvious deterioration of physical and chemical properties. Ordered mesoporous M-NiCeAl catalysts are active and stable in sorbitol hydrogenolysis.

Characterization of the alteration products formed at the surface of LaYSiAlO and CeYSiAlO glasses using ERDA and RBS techniques

International Nuclear Information System (INIS)

Gavarini, S.; Trocellier, P.; Matzen, G.

2004-01-01

Leaching tests have been performed on LnYSiAlO glasses (Ln = La or Ce) that are considered as potential matrices for the specific immobilization of minor actinides. Elastic recoil detection analysis (ERDA) performed on leached samples indicated a superficial hydration of LaYSiAlO glass of about 100-150 nm. This hydrated layer is (Al, Y)-enriched according to SEM-EDS analysis, suggesting the formation of hydroxide (or hydroxycarbonates) compounds including these two elements. This process leads to a very efficient passivation of the material due to the low solubility of Al and Y hydroxides (and hydroxycarbonates) species in near neutral media, even when the solution is rapidly replenished is dynamic leaching experiments. Rutherford Backscattering Spectrometry elemental mapping revealed very localized and significantly Y-enriched deposits at the surface of the sample after leaching. This could be the sign of heterogeneities already present on the pristine glass. These may be correlated with the weak solubility of yttrium (and rare earth) elements in silicate matrices (Y + Ln initial content in the glass ∼11 at.%). In the case of CeYSiAlO glass, a thin layer was formed on the solid after leaching. The simulation of the corresponding RBS spectra showed a surface (Y, Ce)-enrichment and (Al, Si)-depletion in both cases. This could be explained by the oxidation of trivalent cerium initially present in the glass structure during leaching. This might be explained by the low solubility of Ce(IV)-compounds (CeO 2 and/or Ce(OH) 4 ) in solution leading to an enrichment of this element at the glass/solution interface, to form a mixture of amorphous CeO 2 and Y(OH) 3 , as confirmed by XPS and XRD experiments

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

Science.gov (United States)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-12-01

Ce3+-doped and Ce3+/Li+-codoped SrAlSi4N7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr3N2, AlN, α-Si3N4, CeN and Li3N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi4N7:Ce3+(Ce3+/Li+) were investigated in this work. The band structure calculated by the DMol3 code shows that SrAlSi4N7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce3+-doped SrAlSi4N7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi4N7 was identified as a major phase of the fired powders, and Sr5Al5Si21N35O2 and AlN as minor phases. Both Ce3+ and Ce3+/Li+ doped SrAlSi4N7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce3+/Li+-doped SrAlSi4N7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr0.97Al1.03Si3.997N\\94\\maccounttest14=t0005_18193 7:Ce3+0.03 with a commercial blue InGaN chip. It indicates that SrAlSi4N7:Ce3+ is a promising yellow emitting down-conversion phosphor for white LEDs.

Tunable emission in Ln3+ (Ce3+/Dy3+, Ce3+/Tb3+) doped KNa3Al4Si4O16 phosphor synthesized by combustion method

Science.gov (United States)

Kolte, M. M.; Pawade, V. B.; Bhattacharya, A. B.; Dhoble, S. J.

2018-05-01

Ln3+ (Ln = Ce3+/Dy3+, Ce3+/Tb3+) doped KNa3Al4Si4O16 phosphor has been synthesized by Combustion method (CS) at 550° C successfully. Ln3+ (Ln = Ce3+, Dy3+, Tb3+) ions when doped in KNa3Al4Si4O16 host lattice, it shows blue and green emission band under the near Ultraviolet (NUV) excitation wavelength. The Photoluminescence excitation (PLE) and emission spectra are observed due to f-f and d-f transition of rare earth ions. Also, an effective energy transfer (ET) study from Ce3+ → Dy3+ and Ce3+ → Tb3+ ions has been studied and confirmed on the basis of Dexter-Foster theory. Further synthesized phosphor is well characterized by XRD, SEM, TEM and decay time measurement. However, the analysis of crystallite size, lattice strain has been studied by using theoretical as well as experimental techniques. Hence, the observed tunable emission in Ln3+ doped KNa3Al4Si4O16 phosphor may be applicable for solid state lighting technology.

Effect of Surface Treatment on Shear Bond Strength between Resin Cement and Ce-TZP/Al2O3

Directory of Open Access Journals (Sweden)

Jong-Eun Kim

2016-01-01

Full Text Available Purpose. Although several studies evaluating the mechanical properties of Ce-TZP/Al2O3 have been published, to date, no study has been published investigating the bonding protocol between Ce-TZP/Al2O3 and resin cement. The aim of this study was to evaluate the shear bond strength to air-abraded Ce-TZP/Al2O3 when primers and two different cement types were used. Materials and Methods. Two types of zirconia (Y-TZP and Ce-TZP/Al2O3 specimens were further divided into four subgroups according to primer application and the cement used. Shear bond strength was measured after water storage for 3 days or 5,000 times thermocycling for artificial aging. Results. The Y-TZP block showed significantly higher shear bond strength than the Ce-TZP/Al2O3 block generally. Primer application promoted high bond strength and less effect on bond strength reduction after thermocycling, regardless of the type of cement, zirconia block, or aging time. Conclusions. Depending on the type of the primer or resin cement used after air-abrasion, different wettability of the zirconia surface can be observed. Application of primer affected the values of shear bond strength after the thermocycling procedure. In the case of using the same bonding protocol, Y-TZP could obtain significantly higher bond strength compared with Ce-TZP/Al2O3.

Effects of Ce concentrations on ignition temperature and surface tension of Mg-9wt.%Al alloy

Directory of Open Access Journals (Sweden)

Deng Zhenghua

2013-03-01

Full Text Available Magnesium alloys are well known for their excellent properties, but the potential issues with oxidation and burning during melting and casting largely limit its industrial applications. The addition of Ce in magnesium alloys can significantly raise ignition-proof performance and change the structure of the oxide film on the surface of the molten metal as well as the surface tension values. Surface tension is an important physical parameter of the metal melts, and it plays an important role in the formation of surface oxide film. In this present work, the ignition temperature and the surface tension of Mg-9wt.%Al alloy with different Ce concentrations were studied. Surface tensions was measured using the maximum bubble pressure method (MBPM. Ignition temperature was measured using NiCr-NiSi type thermocouples and was monitored and recorded via a WXT-604 desk recording device. The results show that the ignition point of Mg-9wt.%Al alloy can be effectively elevated by adding Ce. The ignition temperature reaches its highest point of 720 ℃ when the addition of Ce is 1wt.%. The surface tension of the molten Mg-9wt.%Al alloy decreases exponentially with the increase of Ce addition at the same temperature. Similarly, the experiment also shows that the surface tension of Mg-9wt.%Al alloy decreases exponentially with the increase of temperature.

Luminescence and Tb3+-Ce3+-Eu3+ ion energy transfer in single-crystalline films of Tb3Al5O12:Ce,Eu garnet

International Nuclear Information System (INIS)

Zorenko, Y.; Gorbenko, V.; Voznyak, T.; Batentschuk, M.; Osvet, A.; Winnacker, A.

2008-01-01

The paper is devoted to investigation of the processes of excitation energy transfer between the host cations (Tb 3+ ions) and the activators (Ce 3+ and Eu 3+ ions) in single-crystalline films of Tb 3 Al 5 O 12 :Ce,Eu (TbAG:Ce,Eu) garnet which is considered as a promising luminescent material for the conversion of LED's radiation. The cascade process of excitation energy transfer is shown to be realized in TbAG:Ce,Eu: (i) from Tb 3+ ions to Ce 3+ and Eu 3+ ions; (ii) from Ce 3+ ions to Eu 3+ ions by means of dipole-dipole interaction and through Tb 3+ ion sublattice

A novel yellow-emitting SrAlSi4N7:Ce3+ phosphor for solid state lighting: Synthesis, electronic structure and photoluminescence properties

International Nuclear Information System (INIS)

Ruan, Jian; Xie, Rong-Jun; Funahashi, Shiro; Tanaka, Yoshinori; Takeda, Takashi; Suehiro, Takayuki; Hirosaki, Naoto; Li, Yuan-Qiang

2013-01-01

Ce 3+ -doped and Ce 3+ /Li + -codoped SrAlSi 4 N 7 phosphors were synthesized by gas pressure sintering of powder mixtures of Sr 3 N 2 , AlN, α-Si 3 N 4 , CeN and Li 3 N. The phase purity, electronic crystal structure, photoluminescence properties of SrAlSi 4 N 7 :Ce 3+ (Ce 3+ /Li + ) were investigated in this work. The band structure calculated by the DMol 3 code shows that SrAlSi 4 N 7 has a direct band gap of 3.87 eV. The single crystal analysis of Ce 3+ -doped SrAlSi 4 N 7 indicates a disordered Si/Al distribution and nitrogen vacnacy defects. SrAlSi 4 N 7 was identified as a major phase of the fired powders, and Sr 5 Al 5 Si 21 N 35 O 2 and AlN as minor phases. Both Ce 3+ and Ce 3+ /Li + doped SrAlSi 4 N 7 phosphors can be efficiently excited by near-UV or blue light and show a broadband yellow emission peaking around 565 nm. A highest external quantum efficiency of 38.3% under the 450 nm excitation was observed for the Ce 3+ /Li + -doped SrAlSi 4 N 7 (5 mol%). A white light LED lamp with color temperature of 6300 K and color rendering index of Ra=78 was achieved by combining Sr 0.97 Al 1.03 Si 3.997 N/94/maccounttest14=t0005 1 8193 7 :Ce 3+ 0.03 with a commercial blue InGaN chip. It indicates that SrAlSi 4 N 7 :Ce 3+ is a promising yellow emitting down-conversion phosphor for white LEDs. - Graphical abstract: One-phosphor converted white light-emitting diode (LED) was fabricated by combining a blue LED chip and a yellow-emitting SrAlSi4N7:Ce 3+ phosphor (see inset), which has the color rendering index of 78 and color temperature of 6300 K. - Highlights: • We reported a new yellow nitride phosphor suitable for solid state lighting. • We solved the crystal structure and evidenced a disordered Si/Al distribution. • We fabricated a high color rendering white LEDs by using a single SrAlSi4N7:Ce

Y/Gd-free yellow Lu{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} phosphor for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Park, Kwangwon [Department of Display Science and Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of); Kim, Taehoon; Yu, Youngmoon [LED-Marine Convergence Technology R& BD Center, Pukyong National University, Busan 608−739 (Korea, Republic of); Seo, Kwangil [L-Stone Co. Ltd., Bucheon 421−807 (Korea, Republic of); Kim, Jongsu, E-mail: jsukim@pknu.ac.kr [Department of Display Science and Engineering, Pukyong National University, Busan 608-737 (Korea, Republic of)

2016-05-15

Solid solubility limit of Ce{sup 3+} ions into Lu-based garnet, Lu{sub 3(1−x)}Ce{sub 3x}Al{sub 5}O{sub 12}, was determined as below 6.7 mol% (3x<0.2 mol) through Raman spectra and X−ray diffraction patterns. Above the solid solubility limit (3x≥0.2 mol), Lu{sub 3(1−x)}Ce{sub 3x}Al{sub 5}O{sub 12} phosphors showed the significant redshift to the yellow spectral region without Y{sup 3+} and Gd{sup 3+} ions. The redshift was explained in terms of the local compressive strain at the Ce{sup 3+} sites. The optimized sample (3x=0.4 mol) had a dominant emission wavelength of 548 nm, color coordinate of CIEx=0.421, CIEy=0.548, quantum efficiency of 80%, absorbance of 91%, lumen maintenance of 90% and high color stability at 473 K under 450 nm excitation wavelength, suggesting substitutability for the commercial yellow (Y, Gd){sub 3}(Al, Ga){sub 5}O{sub 12}:Ce{sup 3+} phosphor. The measured decay times at higher Ce{sup 3+} concentration are significantly shortened at higher temperature than that of those at lower Ce{sup 3+} concentration. The yellow Lu{sub 2.6}Ce{sub 0.4}Al{sub 5}O{sub 12} and a commercial red (Sr, Ca)AlSiN{sub 3}:Eu{sup 2+} phosphor were applied to the pc-WLED, it gave an excellent luminous efficiency (138 lm/W) with a slightly lower color rendering index (Ra=76.4) under correlated color temperature of 6500 K compared to those of the (Y, Gd){sub 3}(Al, Ga){sub 5}O{sub 12}:Ce{sup 3+}-based one (136 lm/W, Ra=78.7). Especially, the quantities of the used phosphors were significantly decreased by 20% for the yellow LuAG:Ce and by 40% for the red (Sr, Ca)AlSiN{sub 3}:Eu{sup 2+}. Thus, the Y/Gd−free pure LuAG:Ce yellow phosphors can be used as alternative to the commercial yellow YAG:Ce phosphor.

Effect of Al and Ce oxide layers electrodeposited on OC4004 stainless steel on its corrosion characteristics in acid media

International Nuclear Information System (INIS)

Stoyanova, E.; Nikolova, D.; Stoychev, D.; Stefanov, P.; Marinova, T.

2006-01-01

The changes in the corrosion characteristics of stainless steel OC4004 in 0.1 M HNO 3 after electrodeposition of thin Al and Ce oxide films on it has been investigated. The Ce 2 O 3 -CeO 2 layers have been found to possess a pronounced stabilizing effect on the steel passive state and on its corrosion resistance, respectively, whereas the Al 2 O 3 layers do not improve considerably the corrosion behaviour of the SS/Al 2 O 3 system. A twice-lower corrosion current was observed with a ternary SS/Al 2 O 3 /Ce 2 O 3 -CeO 2 system in the passive region, while the zones of potentials, where the steel is in a stable passive state, are not changed. The obtained results permit the assumption that the cerium oxides layer acts as an effective cathode playing a determining role with respect to the improvement of the corrosion behavior of the steel. It has been concluded that when the SS/Al 2 O 3 /Ce 2 O 3 -CeO 2 system is used in media containing nitric acid, the corrosion will proceed at potentials where the passive state of steel would not be disturbed

Synthesis and effect of Ce and Mn co-doping on photoluminescence characteristics of Ca6AlP5O20:Eu novel phosphors.

Science.gov (United States)

Shinde, K N; Dhoble, S J

2013-01-01

A series of Ca6AlP5O20 doped with rare earths (Eu and Ce) and co-doped (Eu, Ce and Eu,Mn) were prepared by combustion synthesis. Under Hg-free excitation, Ca6AlP5O20:Eu exhibited Eu(2+) (486 nm) emission in the blue region of the spectrum and under near Hg excitation (245 nm), Ca6AlP5O20:Ce phosphor exhibited Ce(3+) emission (357 nm) in the UV range. Photoluminescence (PL) peak intensity increased in Ca6AlP5O20:Eu,Ce and Ca6AlP5O20:Eu, Mn phosphors due to co-activators of Ce(3+) and Mn(2+) ions. As a result, these ions played an important role in PL emission in the present matrix. Ca6AlP5O20:Eu, Ce and Ca6AlP5O20:Eu, Mn phosphors provided energy transfer mechanisms via Ce(3+) → Eu(2+) and Eu(2+) → Mn(2+), respectively. Eu ions acted as activators and Ce ions acted as sensitizers. Ce emission energy was well matched with Eu excitation energy in the case of Ca6AlP5O20:Eu, Ce and Eu ions acted as activators and Mn ions acted as sensitizers in Ca6AlP5O20:Eu, Mn. This study included synthesis of new and efficient phosphate phosphors. The impact of doping and co-doping on photoluminescence properties and energy transfer mechanisms were investigated and we propose a feasible interpretation. Copyright © 2012 John Wiley & Sons, Ltd.

Doping of Czochralski-grown bulk β-Ga2O3 single crystals with Cr, Ce and Al

Science.gov (United States)

Galazka, Zbigniew; Ganschow, Steffen; Fiedler, Andreas; Bertram, Rainer; Klimm, Detlef; Irmscher, Klaus; Schewski, Robert; Pietsch, Mike; Albrecht, Martin; Bickermann, Matthias

2018-03-01

We experimentally evaluated segregation of Cr, Ce and Al in bulk β-Ga2O3 single crystals grown by the Czochralski method, as well as the impact of these dopants on optical properties. The segregation of Cr and Ce and their incorporation into the β-Ga2O3 crystal structure strongly depends on O2 concentration in the growth atmosphere which has a noticeable impact on decomposition of Ga2O3 and Cr2O3, as well as on the charge state of Cr and Ce. Effective segregation coefficients for Cr are in the range of 3.1-1.5 at 7-24 vol% O2, while for Ce they are roughly below 0.01 at 1.5-34 vol% O2. The effective segregation coefficient for Al is 1.1 at 1.5-21 vol% O2. Both dopants Ce and Al have a thermodynamically stabilizing effect on β-Ga2O3 crystal growth by supressing decomposition. While Ce has no impact on the optical transmittance in the ultraviolet and visible regions, in Cr doped crystals we observe three absorption bands due to Cr3+ on octahedral Ga sites, one in the ultraviolet merging with the band edge absorption of β-Ga2O3 and two in the visible spectrum, for which we estimate the absorption cross sections. Al doping also does not induce dopant related absorption bands but clearly shifts the absorption edge as one expects for a solid-solution crystal Ga2(1-x)Al2xO3 still in the monoclinic phase. For the highest doping concentration (Ga1.9Al0.1O3) we estimate an increase of the energy gap by 0.11 eV.

Evaluation of Ce3+ and alkali metal ions Co-doped LiSrAlF6 crystalline scintillators

International Nuclear Information System (INIS)

Wakahara, Shingo; Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Pejchal, Jan; Kurosawa, Shunsuke; Suzuki, Shotaro; Kawaguchi, Noriaki; Fukuda, Kentaro; Yoshikawa, Akira

2013-01-01

High scintillation efficiency of Eu-doped LiSrAlF 6 (LiSAF) and LiCaAlF 6 (LiCAF) codoped with alkali metal ions has been reported in our recent studies. Thus in this paper, we demonstrated the scintillation properties of 1% Ce-doped LiSAF crystals with 1% alkali metal ions co-doping to increase the light yield and understand the scintillation mechanism. The crystals showed intense emission band corresponding to the 5d-4f transition of Ce 3+ , and their light yields under thermal neutron excitation were higher than that of the Ce only doped crystal. Especially, the light yield of Ce–Na co-doped crystal exceeded about two times that of Ce only doped one. -- Highlights: ► Ce-doped and alkali metal co-doped LiSAF crystals were grown by μ-PD method. ► Alkali metal co-doped crystals showed higher light yield than Ce only doped crystal. ► Decay time of alkali metal co-doped LiSAF were longer than that of Ce only doped one

Effects of La and Ce Addition on the Modification of Al-Si Based Alloys

Directory of Open Access Journals (Sweden)

Emad M. Elgallad

2016-01-01

Full Text Available This study focuses on the effects of the addition of rare earth metals (mainly lanthanum and cerium on the eutectic Si characteristics in Al-Si based alloys. Based on the solidification curves and microstructural examination of the corresponding alloys, it was found that addition of La or Ce increases the alloy melting temperature and the Al-Si eutectic temperature, with an Al-Si recalescence of 2-3°C, and the appearance of post-α-Al peaks attributed to precipitation of rare earth intermetallics. Addition of La or Ce to Al-(7–13% Si causes only partial modification of the eutectic Si particles. Lanthanum has a high affinity to react with Sr, which weakens the modification efficiency of the latter. Cerium, however, has a high affinity for Ti, forming a large amount of sludge. Due to the large difference in the length of the eutectic Si particles in the same sample, the normal use of standard deviation in this case is meaningless.

Crystal structure and anisotropic magnetic properties of new ferromagnetic Kondo lattice compound Ce(Cu,Al,Si){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Maurya, A.; Thamizhavel, A.; Dhar, S.K. [Department of Condensed Matter Physics & Materials Science, Tata Institute of Fundamental Research, Homi Bhabha Road, Mumbai 400 005 (India); Provino, A.; Pani, M.; Costa, G.A. [Department of Chemistry, University of Genova, Via Dodecaneso 31, 16146 Genova (Italy); Institute SPIN-CNR, Corso Perrone 24, 16152 Genova (Italy)

2017-03-15

Single crystals of the new compound CeCu{sub 0.18}Al{sub 0.24}Si{sub 1.58} have been grown by high-temperature solution growth method using a eutectic Al-Si mixture as flux. This compound is derived from the binary CeSi{sub 2} (tetragonal α-ThSi{sub 2}-type, Pearson symbol tI12, space group I4{sub 1}/amd) obtained by partial substitution of Si by Cu and Al atoms but showing full occupation of the Si crystal site (8e). While CeSi{sub 2} is a well-known valence-fluctuating paramagnetic compound, the CeCu{sub 0.18}Al{sub 0.24}Si{sub 1.58} phase orders ferromagnetically at T{sub C}=9.3 K. At low temperatures the easy-axis of magnetization is along the a-axis, which re-orients itself along the c-axis above 30 K. The presence of hysteresis in the magnetization curve, negative temperature coefficient of resistivity at high temperatures, reduced jump in the heat capacity and a relatively lower entropy released up to the ordering temperature, and enhanced Sommerfeld coefficient (≈100 mJ/mol K{sup 2}) show that CeCu{sub 0.18}Al{sub 0.24}Si{sub 1.58} is a Kondo lattice ferromagnetic, moderate heavy fermion compound. Analysis of the high temperature heat capacity data in the paramagnetic region lets us infer that the crystal electric field split doublet levels are located at 178 and 357 K, respectively, and Kondo temperature (8.4 K) is of the order of T{sub C} in CeCu{sub 0.18}Al{sub 0.24}Si{sub 1.58}.

Synthesis by Sol-gel and characterization of catalysts Ag/Al2O3-CeO2

International Nuclear Information System (INIS)

Zayas, M.L.; Perez H, R.; Rubio, E.; Velasco, A.

2004-01-01

Aluminia, cerium and mixed oxides Al 2 O 3 -CeO 2 with different relationship Al/Ce (0.75, 0.50 and 0.25) were prepared by sol-gel and used as support for the Ag. The samples were characterized by XRD, DRIFT, TPR and adsorption of N 2 to temperature of liquid nitrogen. The surface area BET showed that the materials that contain aluminia present near values among them. XRD allowed to identify to the cerianite in the oxides that whose support contains cerium and to the α-aluminia. A mixture of phases was observed in the aluminia. Vibration bands attributed to the bond Al-O and Ce-O were observed by DRIFT in the catalytic materials. TPR showed differences in the reducibility of the Ag precursor in the indicative catalysts of a different interaction with the support. (Author)

Size effect on magnetic ordering in Ce3Al11

International Nuclear Information System (INIS)

Wang, C.R.; Chen, Y.Y.; Neeleshwar, S.; Ou, M.N.; Ho, J.C.

2003-01-01

To study the size dependence of magnetic ordering, magnetic measurements have been made between 1.8 and 300 K on Ce 3 Al 11 particles having an average particle size of 1400 A. The nanoparticles were single phase as confirmed by X-ray diffraction. At low temperatures a ferromagnetic transition occurs at T C =6.2 K, which is the same as that for the bulk material. On the other hand, the antiferromagnetic transition at T N =3.2 K for the bulk material is not visible down to 1.8 K. Meanwhile, the slightly smaller Curie constant of nanoparticles as compared to that of the bulk indicates a certain degree of demagnetization of Ce ions when the particle size is sufficiently reduced

Fabrication of Nano-CeO2 and Application of Nano-CeO2 in Fe Matrix Composites

International Nuclear Information System (INIS)

Tiebao, W.; Chunxiang, C.; Xiaodong, W.; Guobin, L.

2010-01-01

It is expatiated that nano-CeO2 is fabricated by the direct sedimentation method. The components and particles diameter of nano-CeO2 powders are analyzed by XRD and SEM . The thermodynamic analysis and acting mechanism of nano-CeO2 with Al in Fe matrix composites are researched, which shows that the reaction is generated between CeO2 and Al in the composite, that is, 3CeO2+4Al - 2Al2O3+3[Ce], which obtains Al2O3 and active [Ce] during the sintering process. The active [Ce] can improve the performance of CeO2/Fe matrix composites. The suitable amount of CeO2 is about 0.05% in CeO2/Fe matrix composites. SEM fracture analysis shows that the toughness sockets in nano-CeO2/Fe matrix composites are more than those in no-added nano-CeO2 composites, which can explain that adding nano-CeO2 into Fe matrix composite, the toughness of the composite is improved significantly. Applied nano-CeO2 to Fe matrix diamond saw blades shows that Fe matrix diamond saw blade is sharper and of longer cutting life than that with no-added nano-CeO2.

Growth and characterization of ceria thin films and Ce-doped {gamma}-Al{sub 2}O{sub 3} nanowires using sol-gel techniques

Energy Technology Data Exchange (ETDEWEB)

Gravani, S; Polychronopoulou, K; Doumanidis, C C; Rebholz, C [Mechanical and Manufacturing Engineering Department, Engineering School, University of Cyprus, 1678, Nicosia (Cyprus); Stolojan, V; Hinder, S J; Baker, M A [Faculty of Engineering and Physical Sciences, University of Surrey, Guildford GU2 7XH (United Kingdom); Cui, Q; Gu, Z [Department of Chemical Engineering and CHN/NCOE Nanomanufacturing Center, University of Massachusetts Lowell, Lowell, MA 01854 (United States); Gibson, P N, E-mail: M.Baker@surrey.ac.uk [Institute for Health and Consumer Protection, Joint Research Centre of the European Commission, 21027 Ispra (Italy)

2010-11-19

{gamma}-Al{sub 2}O{sub 3} is a well known catalyst support. The addition of Ce to {gamma}-Al{sub 2}O{sub 3} is known to beneficially retard the phase transformation of {gamma}-Al{sub 2}O{sub 3} to {alpha}-Al{sub 2}O{sub 3} and stabilize the {gamma}-pore structure. In this work, Ce-doped {gamma}-Al{sub 2}O{sub 3} nanowires have been prepared by a novel method employing an anodic aluminium oxide (AAO) template in a 0.01 M cerium nitrate solution, assisted by urea hydrolysis. Calcination at 500 deg. C for 6 h resulted in the crystallization of the Ce-doped AlOOH gel to form Ce-doped {gamma}-Al{sub 2}O{sub 3} nanowires. Ce{sup 3+} ions within the nanowires were present at a concentration of < 1 at.%. On the template surface, a nanocrystalline CeO{sub 2} thin film was deposited with a cubic fluorite structure and a crystallite size of 6-7 nm. Characterization of the nanowires and thin films was performed using scanning electron microscopy, transmission electron microscopy, electron energy loss spectroscopy, x-ray photoelectron spectroscopy and x-ray diffraction. The nanowire formation mechanism and urea hydrolysis kinetics are discussed in terms of the pH evolution during the reaction. The Ce-doped {gamma}-Al{sub 2}O{sub 3} nanowires are likely to find useful applications in catalysis and this novel method can be exploited further for doping alumina nanowires with other rare earth elements.

Possibility of a two-dimensional spin liquid in CePdAl induced by partial geometric frustration?

Energy Technology Data Exchange (ETDEWEB)

Fritsch, V. [Universitaet Augsburg, Institut fuer Physik, Experimentalphysik VI (Germany); Karlsruher Institut fuer Technologie (Germany); Grube, K.; Kittler, W.; Taubenheim, C.; Loehneysen, H. von [Karlsruher Institut fuer Technologie (Germany); Huesges, Z.; Lucas, S.; Stockert, O. [Max-Planck-Institut fuer chemische Physik fester Stoffe, Dresden (Germany); Green, E. [Hochfeldzentrum Dresden-Rossendorf (Germany)

2015-07-01

CePdAl crystallizes in the hexagonal ZrNiAl structure, where the magnetic ions form a distorted kagome lattice. At T{sub N} = 2.7 K the onset of antiferromagnetic (AF) order is observed. Neutron scattering experiments revealed a partial frustration in the distorted kagome planes of this structure: two-thirds of the Ce moments form ferromagnetic chains, which are antiferromagnetically coupled, the remaining third do not participate in any long-range order. Along the c-axis the magnetic moments exhibit an amplitude modulation. Accordingly, the kagome planes are stacked on top of each other, resulting in corrugated AF planes parallel to the c-axis formed by the ordered magnetic moments, which are separated by the frustrated moments. It is an intriguing and yet unresolved question if this third of frustrated moments forms a spin liquid state in CePdAl. Based on measurements of specific heat, thermal expansion, magnetization and electrical resistivity we want to discuss this possibility.

Role of CeO2 promoter in NiO/α-Al2O3 catalyst for dry reforming of methane

Science.gov (United States)

Loc, Luu Cam; Phuong, Phan Hong; Tri, Nguyen

2017-09-01

A series of Ni/α-Al2O3 (NiAl) catalysts promoted by CeO2 was prepared by co-impregnation methods with content of (NiO+CeO2) being in the range of 10-30 wt%. The NiO:CeO2 weight ratio was fluctuated at 1:1, 1:2 and 1:3. Several techniques, including X-ray powder diffraction (XRD), Hydrogen temperature-programmed reduction (H2-TPR), and transmission electron microscopy (TEM) were used to investigate catalysts' physico-chemical properties. The activity of these catalysts in dry reforming of CH4 was investigated at temperature range of 550-800 °C. The results revealed that the most suitable CeO2 promoted Ni catalyst contained 20 wt% of (NiO+CeO2) and NiO:CeO2 weight ratio of 1:2. The best catalytic performance of catalyst [20(1Ni2Ce)Al] due to a better reducibility resulted in a higher amount of free small particle NiO. At 700 °C and CH4:CO2 molar ratio of 1:1, the conversion of CH4 and CO2 on the most suitable CeO2 promoted Ni catalyst reached 86% and 67%, respectively; H2 and CO selectivity of 90% and H2:CO molar ratio of 1.15 were obtained. Being similar to MgO [1], promoter CeO2 could improve catalytic activity of Ni/α-Al2O3 catalyst at a lower range of temperature. Besides, both MgO and CeO2 had a great impact on improving coke resistance of Ni catalysts. At higher temperature, the role of CeO2 as well as MgO in preventing coke formation on catalyst was clarified by temperature-programmed oxidation (TPO) technique. Coke amount formed after 30-h TOS on 20(1Ni2Ce) catalyst was found to be 22.18 mgC/gcat, being less than on non-promoted catalyst (36.75 mgC/gcat), but more than on 20(1Ni2Mg)Al one (5.25 mgC/gcat).

Ce and Eu-doped LiSrAlF6 scintillators for neutron detectors

International Nuclear Information System (INIS)

Yanagida, Takayuki; Kawaguchi, Noriaki; Fujimoto, Yutaka; Yokota, Yuui; Yamazaki, Atsushi; Watanabe, Kenichi; Kamada, Kei; Yoshikawa, Akira; Chani, Valery

2011-01-01

Ce 1%, Eu 1%, and Eu 2%-doped LiSrAlF 6 (LiSAF) single crystals were grown by the micro-pulling-down method for thermal neutron applications. The crystals were transparent, 2.0 mm in diameter and 20–40 mm in length. Neither visible inclusions nor cracks were observed. Their transmittance spectra were measured. The strong absorption lines were observed at 200, 240, and 300 nm for Ce:LiSAF due to Ce 3+ 4f–5d transition. In Eu:LiSAF, 200 (4f–5d) and 300 (4f–4f) nm absorption lines were detected. The samples demonstrated strong emission peaks at 300 nm (Ce:LiSAF) and 370 nm (Eu:LiSAFs) when they were irradiated with 241 Am α-rays simulating the α-particles from the 6 Li(n, α) reaction. Thermal neutron responses were examined under 252 Cf irradiation. The absolute light yield of Ce, Eu 1%, and Eu 2% crystals were 3400, 18000, and 30000 ph/n, respectively. Main components of the scintillation decay time of Ce, Eu 1%, and Eu 2%-doped LiSAFs were 63, 1293, and 1205 ns.

Structural, luminescence and photophysical properties of novel trimetallic nanocomposite CeO2·ZnO·ZnAl2O4

International Nuclear Information System (INIS)

Subhan, Md Abdus; Ahmed, Tanzir; Sarker, Prosenjit; Pakkanen, Tuula T.; Suvanto, Mika; Horimoto, Masahiro; Nakata, Hiroyasu

2014-01-01

A novel trimetallic nanocomposite was prepared at a temperature of around 220 °C using co-precipitation of their carbonates from aqueous solutions of the metal nitrates. The morphology of the composite was investigated with scanning electron microscopy (SEM). The X-ray, FTIR and SEM/EDS analyses data indicate that as-synthesized composite which was heated at around 220 °C exists in a nanosized form consisting of crystalline Zn 6 Al 2 (OH) 16 CO 3 ·4H 2 O and CeO 2 . Annealing at temperatures between 400 and 920 °C converts the as-synthesized composite to CeO 2 ·ZnO·ZnAl 2 O 4 multi-metal oxide consisting of crystalline CeO 2 , ZnO and semicrystalline ZnAl 2 O 4 . Photoluminescence (PL) spectra of the as-synthesized sample showed emissions at 440 and 590 nm. PL spectra of CeO 2 ·ZnO·ZnAl 2 O 4 annealed at 920 °C was recorded and three sharp lines were observed at 627 nm (1.98 eV), 530 nm (2.34 eV) and 465 nm (2.67 eV) with broad peaks at 540 nm (2.3 eV) and 400 nm (3.1 eV). These sharp lines resemble to those of CeO 2 and the broad peaks originate from ZnO. The indirect band gap of the as-synthesized composite was found to be 2.44 eV. The luminescence lifetime at 4 K was measured to be 38 μs. -- Highlights: • A novel trimetallic nanocomposite, CeO 2 ·ZnO·ZnAl 2 O 4 has been synthesized and characterized. • At around 220 °C as-synthesized samples exist in crystalline Zn 6 Al 2 (OH) 16 CO 3 ·4H 2 O and CeO 2 . • Annealing at temperatures between 400 and 920 °C converts the composite to CeO 2 ·ZnO·ZnAl 2 O 4 . • The luminescence lifetime of the composite at 4 K was measured to be 38 μs. • PL of CeO 2 ·ZnO·ZnAl 2 O 4 shows three sharp peaks at 627 nm, 530 nm and 465 nm

Synthesis by Sol-gel and characterization of catalysts Ag/Al{sub 2}O{sub 3}-CeO{sub 2}; Sintesis por Sol-gel y caracterizacion de catalizadores Ag/Al{sub 2}O{sub 3}-CeO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Zayas, M.L.; Perez H, R. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Rubio, E. [BUAP, Centro de Vinculacion, 72000 Puebla (Mexico); Velasco, A. [BUAP, Facultad de Quimica, 72000 Puebla (Mexico)

2004-07-01

Aluminia, cerium and mixed oxides Al{sub 2}O{sub 3}-CeO{sub 2} with different relationship Al/Ce (0.75, 0.50 and 0.25) were prepared by sol-gel and used as support for the Ag. The samples were characterized by XRD, DRIFT, TPR and adsorption of N{sub 2} to temperature of liquid nitrogen. The surface area BET showed that the materials that contain aluminia present near values among them. XRD allowed to identify to the cerianite in the oxides that whose support contains cerium and to the {alpha}-aluminia. A mixture of phases was observed in the aluminia. Vibration bands attributed to the bond Al-O and Ce-O were observed by DRIFT in the catalytic materials. TPR showed differences in the reducibility of the Ag precursor in the indicative catalysts of a different interaction with the support. (Author)

Effect of Ce addition on microstructure of Al20Cu2Mn3 twin phase in an Al–Cu–Mn casting alloy

International Nuclear Information System (INIS)

Chen Zhongwei; Chen Pei; Li Shishun

2012-01-01

Highlights: ► Rare earth element Ce can retard the formation of the Al 20 Cu 2 Mn 3 twin phase in an Al–Cu–Mn casting alloy. ► Patterns of the particles of the Al 20 Cu 2 Mn 3 phase in Al–Cu–Mn free Ce alloy are more diverse. ► The symmetry of neighboring components of twins is characterized by glide reflection and reflection. ► The twins of Al 20 Cu 2 Mn 3 phase can enhance the mechanical properties of the Al–Cu–Mn casting alloys. - Abstract: Effects of Ce addition on microstructure of Al 20 Cu 2 Mn 3 twin phase and mechanical properties of an Al–Cu–Mn casting alloy were investigated by transmission electron microscopy, selected area electron diffraction, high resolution transmission electron microscopy and tensile test. The results show that rare earth element Ce can retard the formation of the Al 20 Cu 2 Mn 3 phase in the Al–Cu–Mn alloy. Compared with the Ce containing alloy, patterns of particles of the Al 20 Cu 2 Mn 3 phase in the Al–Cu–Mn free Ce alloy are more diverse. The symmetry of neighboring components of twins is characterized by glide reflection and reflection. In addition, twins of the Al 20 Cu 2 Mn 3 phase can enhance the mechanical properties of the Al–Cu–Mn alloy.

Optical properties of white organic light-emitting devices fabricated utilizing a mixed CaAl12O19:Mn4+ and Y3Al5O12:Ce3+ color conversion layer.

Science.gov (United States)

Jeong, H S; Kim, S H; Lee, K S; Jeong, J M; Yoo, T W; Kwon, M S; Yoo, K H; Kim, T W

2013-06-01

White organic light-emitting devices (OLEDs) were fabricated by combining a blue OLED with a color conversion layer made of mixed Y3Al5O12:Ce3+ green and Ca2AlO19:Mn4+ red phosphors. The X-ray diffraction patterns showed that Ce3+ ions in the Y3Al5O12:Ce3+ phosphors completely substituted for the Y3+ ions and the Mn4+ ions in the CaAl12O19:Mn4+ phosphors completely substituted for the Ca2+ ions. Electroluminescence spectra at 11 V for the OLEDs fabricated utilizing a color conversion layer showed that the Commission Internationale de l'Eclairage coordinates for the Y3Al5O12:Ce3+ and CaAl12O19:Mn4+ phosphors mixed at the ratio of 1:5 and 1:10 were (0.31, 0.34) and (0.32, 0.37), respectively, indicative of a good white color.

CePdAl. A frustrated Kondo lattice at a quantum critical point

Energy Technology Data Exchange (ETDEWEB)

Fritsch, Veronika [EP 6, Electronic Correlations and Magnetism, University of Augsburg (Germany); Karlsruhe Institute of Technology (Germany); Sakai, Akito; Gegenwart, Philipp [EP 6, Electronic Correlations and Magnetism, University of Augsburg (Germany); Huesges, Zita; Lucas, Stefan; Stockert, Oliver [Max Planck Institute for Chemical Physics of Solids, Dresden (Germany); Kittler, Wolfram; Taubenheim, Christian; Grube, Kai; Loehneysen, Hilbert von [Karlsruhe Institute of Technology (Germany); Huang, Chien-Lung [Karlsruhe Institute of Technology (Germany); Max Planck Institute for Chemical Physics of Solids, Dresden (Germany)

2016-07-01

CePdAl is one of the rare frustrated Kondo lattice systems that can be tuned across a quantum critical point (QCP) by means of chemical pressure, i. e., the substitution of Pd by Ni. Magnetic frustration and Kondo effect are antithetic phenomena: The Kondo effect with the incipient delocalization of the magnetic moments, is not beneficial for the formation of a frustrated state. On the other hand, magnetic frustrated exchange interactions between the local moments can result in a breakdown of Kondo screening. Furthermore, the fate of frustration is unclear when approaching the QCP, since there is no simple observable to quantify the degree of frustration. We present thermodynamic and neutron scattering experiments on CePd{sub 1-x}Ni{sub x}Al close to the critical concentration x ∼0.14. Our experiments indicate that even at the QCP magnetic frustration is still present, opening the perspective to find new universality classes at such a quantum phase transition.

Hydrogenation of carbon monoxide on Co/MgAl2O4 and Ce-Co/MgAl2O4 catalysts

International Nuclear Information System (INIS)

Kondoh, S.; Muraki, H.; Fujitani

1986-01-01

It is well known that various hydrocarbons are obtained by hydrogenation of CO on Fischer-Tropsch catalysts, the products depending on the catalyst components such as Co, Ni, Fe and Ru: and the reaction conditions, particularly, temperature, pressure, space velocity and H 2 /CO ratio. Further, both reactivity and selectivity of catalysts may be improved by suitable selection of support and an additive. The main program of the present work is to develop a catalyst for producing C 5 + liquid hydrocarbons, as an automobile fuel, by the Fischer-Tropsch synthesis. The authors have studied unique CO catalyst systems consisting of various supports - such as Al 2 O 3 (γ, β, α), MgAl 2 O 4 (alumina magnesia spinel), MgO and additives selected from the lanthanoid elements (LE). The composition of spinel-based supports was altered in a range from 28 mol % excess Al 2 O 3 to 28 mol % excess MgO. Particularly, they found that a MgAl 2 O 4 support with 15-18 mol % excess Al 2 O 3 is the most preferable for our purpose and CeO 2 as the additive for Co/spinel catalyst remarkably improves C 5 + yield. Further, it was confirmed that the catalytic activity of Co-base catalysts agree with the oxidation state of Co-oxides on Co and Co-Ce/spinel catalysts. The performance of Co-based catalysts for the production of higher hydrocarbons from syn-gas were described elsewhere. The items described in this report include (a) selection of supports, (b) selection of optimum reaction conditions for Co-Ce/spinel catalyst, (c) redox characteristics of Co-oxides on a spinel surface, and (d) experimental observation of TPD profiles, adsorption capacities and IR spectra relating to adsorbed CO

New type ternary NiAlCe layered double hydroxide photocatalyst for efficient visible-light photoreduction of CO2 into CH4

Science.gov (United States)

Li, Ji; (Bill Yang, Y. J.

2018-02-01

New type of ternary NiAlCe layered double hydroxide photocatalyst was synthesized by a simple hydrothermal reaction. The obtained photocatalyst shows efficient visible-light activity for CO2 reduction to CH4. We have investigated the optimal Ce content in the catalyst and analyzed the mechanism by materials characterization. Additionally, a novel alkali etching method was used to construct the porous structure. The effect of the porosity and morphologies on the activity is investigated. It is found that the ternary NiAlCe layered double hydroxide photocatalyst with porosity showing the best photocatalytic activity among all the samples. Based on the characterization and first principle calculation, the detailed photocatalytic mechanism of the ternary NiAlCe layered double hydroxide photocatalyst is deduced.

Interaction of Ce{sub 1−x}Er{sub x}O{sub 2−y} nanoparticles with Al{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Krajczyk, L.; Kraszkiewicz, P.; Kepinski, L., E-mail: L.Kepinski@int.pan.wroc.pl

2015-02-01

The interaction of nanocrystalline Ce{sub 0.5}Er{sub 0.5}O{sub 1.75} mixed oxide with an amorphous Al{sub 2}O{sub 3} in oxidizing and reducing atmosphere up to 1100 °C was studied by XRD, TEM, SEM-EDS and BET. Uniform, chemically homogeneous Ce{sub 0.5}Er{sub 0.5}O{sub 1.75} nanoparticles (2 nm in size) were prepared by microemulsion method and deposited on a high surface γ-alumina support. The nanoparticles were structurally and chemically stable in the oxidizing atmosphere up to 1100 °C, exhibiting only an increase of the mean crystallite size to 9 nm after 3 h treatment. Prolonged heating (24 h) at 1100 °C caused partial decomposition of the mixed oxide and reaction of the extracted erbium with the support with formation of hexagonal (P6{sub 3}/mmc) ErAlO{sub 3} aluminate. The same hexagonal ErAlO{sub 3} occurred also in Er/Al{sub 2}O{sub 3} sample prepared by impregnation of Al{sub 2}O{sub 3} support with an aqueous solution of Er nitrate and subjected to heating in air or hydrogen at 1100 °C. In the reducing atmosphere the Ce{sub 0.5}Er{sub 0.5}O{sub 1.75} reacted with Al{sub 2}O{sub 3} already at 800 °C, to form an amorphous surface phase. At 900 °C monoclinic (P2{sub 1}/c) (Er,Ce){sub 4}Al{sub 2}O{sub 9} mixed aluminate was formed with the unit cell volume 4.5% bigger than that of pure Er{sub 4}Al{sub 2}O{sub 9} phase. After 3 h treatment at 1000 °C more than half of the (Er,Ce){sub 4}Al{sub 2}O{sub 9} aluminate decomposed into two nanocrystalline mixed monoaluminates: tetragonal (I4/mcm) (Ce,Er)AlO{sub 3} and hexagonal (P6{sub 3}/mmc) (Er,Ce)AlO{sub 3}. Nanocrystalline mixed aluminate particles with Er{sup 3+} ions placed in well-defined lattice sites and supported at the surface of Al{sub 2}O{sub 3} support, may be interesting as highly efficient active components of optical waveguides amplifiers. - Graphical abstract: Structure evolution of Ce{sub 0.5}Er{sub 0.5}O{sub 1.75} on Al{sub 2}O{sub 3} in air and in H{sub 2}. - Highlights: �

Growth and scintillation properties of Ce{sup 3+}-doped (Y{sub 1-x}Gd{sub x})AlO{sub 3} crystals

Energy Technology Data Exchange (ETDEWEB)

Fujimoto, Yutaka; Wakahara, Shingo; Suzuki, Shotaro; Kurosawa, Shunsuke [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yanagida, Takayuki [New Industry Creation Hatchery Center, Tohoku University, 6-6-10 Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Yoshikawa, Akira [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); New Industry Creation Hatchery Center, Tohoku University, 6-6-10 Aramaki, Aoba-ku, Sendai 980-8579 (Japan)

2012-12-15

The optical and scintillation properties of 0.5% fixed Ce-doped (Y{sub 1-x}Gd{sub x})AlO{sub 3} single crystals have been investigated at three different levels of Gd doping: x = 0.2, 0.4 and 0.6. Single crystal of the Ce{sup 3+}-doped (Y{sub 0.8}Gd{sub 0.2})AlO{sub 3}, (Y{sub 0.6}Gd{sub 0.4})AlO{sub 3} and (Y{sub 0.4}Gd{sub 0.6})AlO{sub 3} were successfully grown by {mu}-PD technique in nitrogen atmosphere. From X-ray diffraction analysis, no impurity phase was detected for the grown Ce-doped crystals. Ce-doped (Y{sub 0.6}Gd{sub 0.4})AlO{sub 3} crystal demonstrated highest fluorescence quantum efficiency ({proportional_to} 25%) with improvement of excitation efficiency due to the Gd-doping. When irradiated by the alpha-rays from a {sup 241}Am source, all the Ce-doped crystals showed luminescence band that corresponding to 5d (t{sub 2g})-4f transition of Ce{sup 3+}. The scintillation decay time was characterized by two components; the fast component (5-15 ns) is ascribed to 5d-4f transition of Ce{sup 3+}, while the slow one (100-200 ns) may be related to energy transfer between Ce{sup 3+} and Gd{sup 3+} ion. According to the result of {sup 137}Cs gamma-ray irradiated pulse height spectra compared with BGO scintillator, the relative scintillation light output was found to be about 12200 {+-} 1220 (Gd 20%) and 16000 {+-} 1600 (Gd 40%) ph/MeV. (copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Promoting Effect of CeO2 Addition on Activity and Catalytic Stability in Steam Reforming of Methane over Ni/Al2O3

International Nuclear Information System (INIS)

Rakib, A.; Gennequin, C.; Ringot, S.; Aboukais, A.; Abi-Aad, E.; Dhainaut, T.

2011-01-01

Hydrogen production by steam reforming of methane was studied over Ni catalysts supported on CeO 2 , Al 2 O 3 and CeO 2 -Al 2 O 3 . These catalysts were prepared using the impregnation method and characterized by XRD. The effect of CeO2 promoter on the catalytic performance of Ni/Al 2 O 3 catalyst for methane steam reforming reaction was investigated. In fact, CeO 2 had a positive effect on the catalytic activity in this reaction. Experimental results demonstrated that Ni/CeO 2 -Al 2 O 3 catalyst showed excellent catalytic activity and high reaction performance. In addition, the effects of reaction temperature and metal content on the conversion of CH 4 and H 2 /CO ratio were also investigated. Results indicated that CH4 conversion increased significantly with the increase of the reaction temperature and metal content. (author)

Single crystal study of antiferromagnetic CePd3Al9

International Nuclear Information System (INIS)

Baumbach, R E; Scott, B L; Ronning, F; Thompson, J D; Bauer, E D

2014-01-01

Single crystal x-ray diffraction, magnetic susceptibility (M), heat capacity (C), and electrical resistivity (ρ) measurements are reported for specimens of the new tetragonal compound CePd 3 Al 9 , which forms in a new structure type. X-ray diffraction measurements reveal that the nearest neighbor Ce–Ce distances are large (d Ce–Ce  = 5.272 Å), suggesting that this compound may be described as a stoichiometric dilute Kondo lattice. Thermodynamic and transport measurements reveal antiferromagnetic order near T N  = 0.9 K. The ordered ground state emerges from a lattice of localized Ce ions that are weakly hybridized with the conduction electrons, as revealed by the moderate electronic coefficient of the specific heat γ ≈ 45 mJ mol −1  K −2 (extrapolated from above T N ) and the lack of evidence for Kondo coherence in the magnetic susceptibility and electrical resistivity. The application of a magnetic field initially suppresses the magnetic order at a rate of −0.04 K kOe −1 , but Zeeman splitting of the doublet ground state produces a nonmagnetic singlet before T N reaches zero. The data additionally reveal that chemical/structural disorder plays an important role, as evidenced by results from single crystal x-ray diffraction, the broadness of the peak at T N in the heat capacity, and the small residual resistivity ratio RRR = ρ 300 K /ρ 0  = 1.3. (paper)

Broadband white light emission from Ce:AlN ceramics: High thermal conductivity down-converters for LED and laser-driven solid state lighting

Directory of Open Access Journals (Sweden)

A. T. Wieg

2016-12-01

Full Text Available We introduce high thermal conductivity aluminum nitride (AlN as a transparent ceramic host for Ce3+, a well-known active ion dopant. We show that the Ce:AlN ceramics have overlapping photoluminescent (PL emission peaks that cover almost the entire visible range resulting in a white appearance under 375 nm excitation without the need for color mixing. The PL is due to a combination of intrinsic AlN defect complexes and Ce3+ electronic transitions. Importantly, the peak intensities can be tuned by varying the Ce concentration and processing parameters, causing different shades of white light without the need for multiple phosphors or light sources. The Commission Internationale de l’Eclairage coordinates calculated from the measured spectra confirm white light emission. In addition, we demonstrate the viability of laser driven white light emission by coupling the Ce:AlN to a readily available frequency tripled Nd-YAG laser emitting at 355 nm. The high thermal conductivity of these ceramic down-converters holds significant promise for producing higher power white light sources than those available today.

Synthesis and characterization of molybdenum catalysts supported on γ-Al2O3-CeO2 composite oxides

International Nuclear Information System (INIS)

Farooq, Muhammad; Ramli, Anita; Subbarao, Duvvuri

2012-01-01

The physical and chemical properties of a catalyst play a vital role in various industrial applications. Molybdenum catalysts supported on γ-Al 2 O 3 and γ-Al 2 O 3 -CeO 2 mixed oxides with varying loading of CeO 2 (5, 10, 15, 20 wt% with respect to γ-Al 2 O 3 ) were prepared by wet impregnation method. The physiochemical properties of these synthesized Mo catalysts were studied with various characterization techniques such as X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR), field emission scanning electron microscopy-energy dispersive analysis (FESEM-EDX) and X-ray fluorescence spectrometer (XRF). The results showed that the addition of CeO 2 into the support affected the binding energies of the elements and reducibility of the metal oxides formed after calcination of catalyst samples due to the change in metal-support interaction. Further, the characterization techniques showed that the active metal was well dispersed on the surface of support material.

The Complete Oxidation of Ethanol at Low Temperature over a Novel Pd-Ce/γ-Al2O3-TiO2 Catalyst

International Nuclear Information System (INIS)

Wang, Yanping; Zhao, Jinshuang; Wang, Xiaoli; Li, Zhe; Liu, Pengfei

2013-01-01

Pd-Ce/γ-Al 2 O 3 -TiO 2 catalysts were prepared by combined sol.gel and impregnation methods. Transmission electron microscopy, X-ray diffraction, H 2 -temperature-programmed reduction, O 2 -temperature-programmed desorption, and ethanol oxidation experiments were conducted to determine the properties of the catalysts. Addition of an optimal amount of Ce improved the performance of the Pd/γ-Al 2 O 3 -TiO 2 catalyst in promoting the complete oxidation of ethanol. The catalyst with 1% Ce exhibited the highest activity, and catalyzed complete oxidation of ethanol at 175 .deg. C; its selectivity to CO 2 reached 87%. Characterization results show that addition of appropriate amount of Ce could enrich the PdO species, and weaken the Pd-O bonds, thus enhancing oxidation ability of the catalyst. Meanwhile, the introduction of CeO 2 could make PdO better dispersed on γ-Al 2 O 3 -TiO 2 , which is beneficial for the improvement of the catalytic oxidation activity

Effect of Trace Ce on Microstructure and Properties of Near-rapidly Solidified Al-Zn-Mg-Cu Alloys

Directory of Open Access Journals (Sweden)

HUANG Gao-ren

2018-03-01

Full Text Available Through using DSC, XRD, SEM, EDS, static tensile test and other analysis methods of materials, the effect of trace Ce on microstructure and properties of near-rapidly solidified Al-Zn-Mg-Cu alloy was studied in order to find out rational homogenizing heat treatment process. The results show that Ce plays a role of refining grain and purifying molten alloy. The addition of Ce reduces dendritic spacing, refines the grain structures, eliminates dispersed shrinkage. The addition of Ce reduces the initial melting point of low melting eutectic phases by 3℃, under the same homogenization conditions. Trace Ce promotes the dissolution of low melting eutectic phases into the matrix, which improves the effect of homogenization. Homogenization temperatures of alloy A should be lower than 480℃and alloy B should be lower than 470℃; the addition of Ce decreases the homogenization temperature and improves the homogenization effect. The addition of Ce also greatly increases the tensile strength of the alloys.

Scintillation and optical properties of Ce{sup 3+}-doped CaGdAl{sub 3}O{sub 7} single crystals

Energy Technology Data Exchange (ETDEWEB)

Mori, Masaki, E-mail: masaki.mori.mz4@ms.naist.jp [Graduate School of Materials Science, Nara Institute of Science and Technology (NAIST), 8916-5 Takayama-cho, Ikoma-shi, Nara 630-0192 (Japan); Nakauchi, Daisuke; Okada, Go [Graduate School of Materials Science, Nara Institute of Science and Technology (NAIST), 8916-5 Takayama-cho, Ikoma-shi, Nara 630-0192 (Japan); Fujimoto, Yutaka [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai, 980-8579 (Japan); Kawaguchi, Noriaki [Graduate School of Materials Science, Nara Institute of Science and Technology (NAIST), 8916-5 Takayama-cho, Ikoma-shi, Nara 630-0192 (Japan); Koshimizu, Masanori [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai, 980-8579 (Japan); Yanagida, Takayuki [Graduate School of Materials Science, Nara Institute of Science and Technology (NAIST), 8916-5 Takayama-cho, Ikoma-shi, Nara 630-0192 (Japan)

2017-06-15

The single crystals of 0, 0.6, 1, 1.6 and 2 mol% Ce doped CaGdAl{sub 3}O{sub 7} (Ce:CGAM) were grown by the Floating Zone method, and investigated on photoluminescence (PL) and scintillation properties. In the PL spectra, a broad emission appeared over 380–500 nm under 280 and 360 nm excitations with the quantum yield of 33.8–38.8%. Under a vacuum ultraviolet excitation (90 nm) using a synchrotron source, non-doped CGAM single crystal showed broad emissions over 250–650 nm. The PL decay time profiles followed a monotonic exponential decay with a decay time constant of around 33 ns. The scintillation spectra were similar to those of PL. All of the samples exhibited a clear photoabsorption peak and Compton edge in the pulse height spectra measured under {sup 137}Cs γ-ray irradiation, and the absolute scintillation light yield (LY) was highest for the 2% Ce-doped sample with the value of 3300±300 ph/MeV. The scintillation decay profiles were approximated by a third order exponential decay function, and the extracted decay time of Ce{sup 3+} emission component was around 36–44 ns. Among all the samples, 2%Ce:CGAM single crystal sample showed the best afterglow level as a scintillator under X-ray irradiation. - Highlights: •Ce{sup 3+}-doped CaGdAl{sub 3}O{sub 7} single crystals were synthesized by the FZ method. •Optical and scintillation properties of Ce{sup 3+}-doped CaGdAl{sub 3}O{sub 7} were investigated. •Photoabsorption peak in a pulse height spectrum was clearly observed under γ-rays.

Dehydrogenation of Surface-Oxidized Mixtures of 2LiBH4 + Al/Additives (TiF3 or CeO2

Directory of Open Access Journals (Sweden)

Juan Luis Carrillo-Bucio

2017-11-01

Full Text Available Research for suitable hydrogen storage materials is an important ongoing subject. LiBH4–Al mixtures could be attractive; however, several issues must be solved. Here, the dehydrogenation reactions of surface-oxidized 2LiBH4 + Al mixtures plus an additive (TiF3 or CeO2 at two different pressures are presented. The mixtures were produced by mechanical milling and handled under welding-grade argon. The dehydrogenation reactions were studied by means of temperature programmed desorption (TPD at 400 °C and at 3 or 5 bar initial hydrogen pressure. The milled and dehydrogenated materials were characterized by scanning electron microscopy (SEM, X-ray diffraction (XRD, and Fourier transformed infrared spectroscopy (FT-IR The additives and the surface oxidation, promoted by the impurities in the welding-grade argon, induced a reduction in the dehydrogenation temperature and an increase in the reaction kinetics, as compared to pure (reported LiBH4. The dehydrogenation reactions were observed to take place in two main steps, with onsets at 100 °C and 200–300 °C. The maximum released hydrogen was 9.3 wt % in the 2LiBH4 + Al/TiF3 material, and 7.9 wt % in the 2LiBH4 + Al/CeO2 material. Formation of CeB6 after dehydrogenation of 2LiBH4 + Al/CeO2 was confirmed.

Luminescence and scintillation response of YGd.sub.2./sub.Al.sub.2./sub.Ga.sub.3./sub.O.sub.12./sub.:Ce and LuGd.sub.2./sub.Al.sub.2./sub.Ga.sub.3./sub.O.sub.12./sub.:Ce scintillators

Czech Academy of Sciences Publication Activity Database

Chewpraditkul, Wa.; Pattanaboonmee, N.; Chewpraditkul, W.; Kamada, K.; Yoshikawa, A.; Nikl, Martin

2016-01-01

Roč. 90, Jul (2016), s. 153-156 ISSN 1350-4487. [International Conference on Luminescent Detectors and Transformers of Ionizing Radiation (LUMDETR). Tartu (Estonsko), 20.09.2015-25.09.2015] R&D Projects: GA ČR GAP204/12/0805 Institutional support: RVO:68378271 Keywords : YGd 2 Al 2 Ga 3 O 12 :Ce * LuGd 2 Al 2 Ga 3 O 12 :Ce * light yield * luminescence * scintillation Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.442, year: 2016

Luminescence and energy transfer in Lu3Al5O12 scintillators co-doped with Ce3+ and Pr3+

NARCIS (Netherlands)

Ogiegło, J.M.; Zych, A.K.; Jüstel, T.; Meijerink, A.; Ronda, R.C.

2013-01-01

Lu3Al5O12:Ce3+ (LuAG:Ce) is a scintillator with a fast response time. The light yield is lower than theoretically expected and to increase the light yield co-doping with Pr3+ is investigated. To better understand the energy flow to the Ce3+ ion, first low temperature emission and excitation spectra

Plasma-catalyst hybrid reactor with CeO2/γ-Al2O3 for benzene decomposition with synergetic effect and nano particle by-product reduction.

Science.gov (United States)

Mao, Lingai; Chen, Zhizong; Wu, Xinyue; Tang, Xiujuan; Yao, Shuiliang; Zhang, Xuming; Jiang, Boqiong; Han, Jingyi; Wu, Zuliang; Lu, Hao; Nozaki, Tomohiro

2018-04-05

A dielectric barrier discharge (DBD) catalyst hybrid reactor with CeO 2 /γ-Al 2 O 3 catalyst balls was investigated for benzene decomposition at atmospheric pressure and 30 °C. At an energy density of 37-40 J/L, benzene decomposition was as high as 92.5% when using the hybrid reactor with 5.0wt%CeO 2 /γ-Al 2 O 3 ; while it was 10%-20% when using a normal DBD reactor without a catalyst. Benzene decomposition using the hybrid reactor was almost the same as that using an O 3 catalyst reactor with the same CeO 2 /γ-Al 2 O 3 catalyst, indicating that O 3 plays a key role in the benzene decomposition. Fourier transform infrared spectroscopy analysis showed that O 3 adsorption on CeO 2 /γ-Al 2 O 3 promotes the production of adsorbed O 2 - and O 2 2‒ , which contribute benzene decomposition over heterogeneous catalysts. Nano particles as by-products (phenol and 1,4-benzoquinone) from benzene decomposition can be significantly reduced using the CeO 2 /γ-Al 2 O 3 catalyst. H 2 O inhibits benzene decomposition; however, it improves CO 2 selectivity. The deactivated CeO 2 /γ-Al 2 O 3 catalyst can be regenerated by performing discharges at 100 °C and 192-204 J/L. The decomposition mechanism of benzene over CeO 2 /γ-Al 2 O 3 catalyst was proposed. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of Ce-rich rare earth on microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy

Directory of Open Access Journals (Sweden)

You Zhiyong

2012-05-01

Full Text Available To improve the comprehensive mechanical properties of Mg-10Zn-5Al-0.1Sb magnesium alloy, different amount of Ce-rich rare earth (RE was added to the alloy, and the effect of RE addition on the microstructure and mechanical properties of Mg-10Zn-5Al-0.1Sb alloy was investigated by means of Brinell hardness measurement, scanning electron microscopy (SEM, energy dispersive spectroscope (EDS and X-ray diffraction (XRD. The results show that an appropriate amount of Ce-rich rare earth addition can make the Al4Ce phase particles and CeSb phase disperse more evenly in the alloy. These phases refine the alloy抯 matrix and make the secondary phases [t-Mg32(Al,Zn49 phase and f-Al2Mg5Zn2 phase] finer and more dispersive, therefore significantly improve the mechanical properties of the Mg-10Zn-5Al-0.1Sb alloy. When the RE addition is 1.0 wt.%, the tensile strengths of the alloy both at room temperature and 150 篊 reach the maximum values while the impact toughness is slightly lower than that of the matrix alloy. The hardness increases with the increase of RE addition.

PREPARATION AND VISIBLE LIGHT RESPONSIVE PHOTOCATALYTIC ACTIVITY OF Fe3O4/Ni-Al-Ce LDH/Bi2WO6 COMPOSITES

Directory of Open Access Journals (Sweden)

Jiaqi Hao

Full Text Available Novel Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites were prepared through a hydrothermal method and co-precipitation method. The morphologies and structures of the photocatalysts were characterized by XRD, Raman, TEM, UV-vis-DRS, BET surface area and VSM techniques. The photocatalytic performances of the photocatalysts were investigated by the decolorization of methyl orange (MO under visible-light irradiation. The results showed that the Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites exhibited greater photocatalytic activities compared to pure Bi2WO6 and the Ni-Al-Ce LDH; the decolorization rate of MO was 87% within 60 min under visible-light irradiation. The decolorization efficiency of the composite material remained at 71% after 4 recycling runs, showing improved stability. Furthermore, the experimental results also showed that the photocatalytic reactions for the composites followed first-order reaction kinetics. Therefore, the Fe3O4/Ni-Al-Ce LDH/Bi2WO6 composites were photocatalysts with high efficiencies and stabilities for a photocatalytic reaction of an organic pollutant, and this study provides a new, effective method for the development of wastewater treatment.

Towards Bright and Fast Lu3Al5O12:Ce,Mg Optical Ceramics Scintillators

CERN Document Server

Liu, Shuping; Feng, Xiqi; Vedda, Anna; Fasoli, Mauro; Shi, Yun; Kou, Huamin; Beitlerova, Alena; Wu, Lexiang; D'Ambrosio, Carmelo; Pan, Yubai; Nikl, Martin

2016-01-01

The recent advent of Lu 3 Al 5 O 12 :Ce optical ceramics marks a turning point in scintillator material technology. Because of their lower preparation tem-perature, brightness, and robustness such materials can now compete with single crystals. Their further scintillation effi ciency optimization includes the thorough control of the defects responsible for optical and scintillation losses. The choice of sintering agent appears critical to achieve both high optical transparency and scintillation performance. In this work, the optical investi-gations coupled with X-ray absorption near-edge spectroscopy evidence the benefi cial role of MgO sintering agent. Mg 2+ co-dopants in ceramics drive the partial conversion of Ce 3+ to Ce 4+ . The Ce 4+ center, however, does not impair the scintillation performance due to its capability to positively infl uence the scintillation process. The importance of simultaneous application of such co-doping and annealing treatment is also demonstrated. With 0.3 at% Mg, our cer...

Grado de satisfacción laboral de los Directores de las Instituciones Educativas de Educación Básica Regular vinculadas al Programa de Educación Rural de Fe y Alegría Nº48 de Malingas –Tambogrande

OpenAIRE

Távara Ma-San, Carlos Gabriel

2015-01-01

La investigación tiene como objetivo identificar el grado de satisfacción laboral de los directores de las instituciones educativas de Educación Básica Regular vinculadas al Programa de Educación Rural de Fe y Alegría Nº 48 de Malingas –Tambogrande. Para ello, se aplicó de manera anónima a 25 directores un "Cuestionario de Satisfacción Laboral" constituido por 35 ítems como instrumento para cuantificar las ocho dimensiones relacionadas con la satisfacción laboral mediante procesamiento estadí...

Sequential evolution of different phases in metastable Gd(2-x)Ce(x)Zr(2-x)Al(x)O7 (0.0 ≤ x ≤ 2.0) system: crucial role of reaction conditions.

Science.gov (United States)

Shukla, Rakesh; Sayed, Farheen N; Phapale, Suhas; Mishra, Ratikant; Tyagi, Avesh K

2013-07-15

The Gd(2-x)Ce(x)Zr(2-x)Al(x)O7 (0.0 ≤ x ≤ 2.0) series was synthesized by the gel combustion method. This system exhibited the presence of a fluorite-type phase, along with a narrow biphasic region, depending upon the Ce/Gd content in the sample. Thermal stability of these new compounds under oxidizing and reducing conditions has been investigated. The products obtained on decomposition of Gd(2-x)Ce(x)Zr(2-x)Al(x)O7 in oxidizing and reducing conditions were found to be entirely different. It was observed that in air the fluorite-type solid solutions of Gd(2-x)Ce(x)Zr(2-x)Al(x)O7 composition undergo phase separation into perovskite GdAlO3 and fluorite-type solid solutions of Gd-Ce-Zr-O or Ce-Zr-Al-O depending upon the extent of Ce and Al substitution. On the other hand, Gd(2-x)Ce(x)Zr(2-x)Al(x)O7 samples on heating under reducing conditions show a phase separation to CeAlO3 perovskite and a defect-fluorite of Gd2Zr2O7. The extent of metastability for a typical composition of Gd(1.2)Ce(0.8)Zr(1.2)Al(0.8)O7 (nano), Gd(1.2)Ce(0.8)Zr(1.2)Al(0.8)O(6.6) (heated under reduced conditions), Gd(1.2)Ce(0.8)Zr(1.2)Al(0.8)O7 (heated in air at 1200 °C) has been experimentally determined employing a high temperature Calvet calorimeter. On the basis of thermodynamic stability data, it could be inferred that the formation of a more stable compound in the presence of two competing cations (i.e., Gd(3+) and Ce(3+)) is guided by the crystallographic stability.

Removals of aqueous sulfur dioxide and hydrogen sulfide using CeO2-NiAl-LDHs coating activated carbon and its mix with carbon nano-tubes

KAUST Repository

Li, Jing; Chen, Fangping; Jin, Guanping; Feng, Xiaoshuang; Li, Xiaoxuan

2015-01-01

Ce-doped NiAl/layered double hydroxide was coated at activated carbon by urea hydrolysis method (CeO2-NiAl-LDHs/AC) in one pot, which was characterized by X-ray diffraction, infrared spectra, field emission scanning electron microscope and electrochemical techniques. CeO2-NiAl-LDHs/AC shows good uptake for aqueous sulfur dioxide (483.09mg/g) and hydrogen sulfide (181.15mg/g), respectively at 25°C. Meanwhile, the electrochemical removals of aqueous sulfur dioxide and hydrogen sulfide were respectively investigated at the mix of CeO2-NiAl-LDHs/AC and carbon nano-tubes modified homed paraffin-impregnated electrode. Both sulfur dioxide and hydrogen sulfide could be effectively oxidized to sulfuric acid at 1.0V in alkaline aqueous solution. © 2015 Elsevier B.V.

Removals of aqueous sulfur dioxide and hydrogen sulfide using CeO2-NiAl-LDHs coating activated carbon and its mix with carbon nano-tubes

KAUST Repository

Li, Jing

2015-07-01

Ce-doped NiAl/layered double hydroxide was coated at activated carbon by urea hydrolysis method (CeO2-NiAl-LDHs/AC) in one pot, which was characterized by X-ray diffraction, infrared spectra, field emission scanning electron microscope and electrochemical techniques. CeO2-NiAl-LDHs/AC shows good uptake for aqueous sulfur dioxide (483.09mg/g) and hydrogen sulfide (181.15mg/g), respectively at 25°C. Meanwhile, the electrochemical removals of aqueous sulfur dioxide and hydrogen sulfide were respectively investigated at the mix of CeO2-NiAl-LDHs/AC and carbon nano-tubes modified homed paraffin-impregnated electrode. Both sulfur dioxide and hydrogen sulfide could be effectively oxidized to sulfuric acid at 1.0V in alkaline aqueous solution. © 2015 Elsevier B.V.

Synthesis and dosimetric characterization of Sr{sub 4}Al{sub 14}O{sub 25}: Ce{sup 2+}

Energy Technology Data Exchange (ETDEWEB)

Leon M, M. I.; Sosa A, M.; Vallejo, M. A.; Azorin V, J. C. [Universidad de Guanajuato, Division de Ciencias e Ingenierias, Loma del Bosque No. 103, 37150 Leon, Guanajuato (Mexico); Diaz T, L. A., E-mail: leonmm2011@licifug.ugto.mx [Centro de Investigaciones en Optica, A. C., Grupo de Espectroscopia de Materiales Avanzados y Nanoestructurados, 37150 Leon, Guanajuato (Mexico)

2015-10-15

Full text: Strontium aluminates phosphors activated by Ce{sup +2} were prepared by combustion method at 600 degrees C and calcined on air and reducing atmospheres. Photoluminescence (Pl) and thermoluminescence (Tl) properties were investigated and X-ray powder diffraction analysis confirmed the formation of Sr{sub 4}Al{sub 14}O{sub 25}: Ce{sup +2}. The Pl spectrum shows a peak around 430 nm (330 nm excitation).Thermoluminescence studies were done with two different concentrations of Ce, 0.5% mol and 1% mol respective. According to our studies, the Tl intensity is proportional to dopant concentration, irradiation dose and calcination atmosphere. (Author)

Using Ce to modify inclusion in spring steel

Directory of Open Access Journals (Sweden)

Wang Q.

2017-01-01

Full Text Available The effect of rare earth metals addition on the Al2O3 inclusions in spring steel used in fastener of high speed railway was investigated by metallographic examination, SEM-EDS and composition analysis. To deform those harmful inclusions to improve material performance，the evolution process of Al2O3 inclusions was investigated through the surface and line scanning. Ce metal modifying Al2O3 is a stepwise reduction process based on a formation of ring shape Ce-riched band around the Al2O3 inclusions during reaction process. Through experiment and thermodynamic calculation, an evolvement rule about Al2O3 inclusions change after Ce addition is obtained, i.e. Al2O3→Ce2O3-Al2O3→Ce2O2S. Changing the inclusions from Al2O3 to rare earth inclusions could improve the resistance to pitting corrosion based on potentiodynamic anodic polarization test.

Crystal growth and scintillation properties of Ce and Eu doped LiSrAlF{sub 6}

Energy Technology Data Exchange (ETDEWEB)

Yamaji, Akihiro, E-mail: yamaji-a@imr.tohoku.ac.jp [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Yanagida, Takayuki [New Industry Creation Hatchery Center (NICHe), Tohoku University, 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Kawaguchi, Noriaki [Tokuyama Corporation, Shibuya 3-chome, Shibuya, Tokyo 150-8383 (Japan); Fujimoto, Yutaka; Yokota, Yuui [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Watanabe, Kenichi; Yamazaki, Atsushi [Department of Material, Physics and Energy Engineering, Nagoya University, Furo-cho, Chikusa-ku, Nagoya, 464-8603 (Japan); Yoshikawa, Akira [Institute of Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); New Industry Creation Hatchery Center (NICHe), Tohoku University, 6-6-10 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Pejchal, Jan [Institute of Physics AS CR, Cukrovarnicka 10, 16200 Prague 6 (Czech Republic)

2011-12-11

Ce and Eu doped LiSrAlF{sub 6} (LiSAF) single crystals for the neutron detection with different dopant concentrations were grown by the micro-pulling-down method ({mu}-PD). In Ce:LiSAF, intense emission peaks due to Ce{sup 3+} 5d-4f transitions were observed at approximately 315 and 335 nm in photo- and {alpha}-ray induced radio-luminescence spectra. In case of Eu:LiSAFs, an intense emission peak at 375 nm due to Eu{sup 2+} 5d-4f transition was observed in the radio-luminescence spectra. The pulse height spectra and decay time profiles were measured under {sup 252}Cf neutron irradiation to examine the neutron response. The Ce 3% and Eu 2% doped LiSAF showed the highest light yield of 2860 ph/n with 19 ns main decay time component and 24,000 ph/n with 1610 ns.

Improvement of photoluminescence intensity of Ce-doped Y{sub 3}Al{sub 5}O{sub 12} phosphor by Si{sub 3}N{sub 4} addition

Energy Technology Data Exchange (ETDEWEB)

Shyu, Jiin-Jyh, E-mail: jjshyu@ttu.edu.tw; Yang, Chia-Wei

2017-06-01

Yttrium aluminum garnet (Y{sub 3}Al{sub 5}O{sub 12}, YAG) has been widely used as a host for luminescent ions. The present paper describes the effects of Si{sub 3}N{sub 4} addition on the formation and photoluminescence properties of the Ce-doped YAG yellow phosphors. Phosphor powders with the nominal compositions of Y{sub 2.95}Ce{sub 0.05}Al{sub 5-m}Si{sub m}O{sub 12-m}N{sub m} (m = 0–0.6) were prepared by calcining the mixed raw materials at 1500 °C in nitrogen atmosphere. X-ray diffraction, x-ray photoelectron spectroscopy, scanning electron microscope, and transmission electron microscopy equipped with an energy dispersive x-ray spectrometer were used to characterize the structure of the calcined powders. The photoluminescence properties were measured with fluorescence spectrophotometry. It was found that in the range of m = 0–0.27, single phase YAG solid solution (s.s.) in which the Y, Al, and O sites are partially occupied by Ce, Si, and N ions, respectively. The nitrogen ions do not distribute homogeneously over the YAG lattice. The tendency to bond with nitrogen ion for the cations is (Y, Ce) > Si > Al. With the increase in the Si{sub 3}N{sub 4} content, the increase in both the Ce{sup 3+}/(Ce{sup 3+} + Ce{sup 4+}) ratio and the Ce-N bonds improve the intensity of the photoluminescent emission. At m = 0.27, the emission intensity reaches a maximum which is about 2.5 and 1.6 times of that for the Si{sub 3}N{sub 4}-free composition (m = 0) calcined in air and nitrogen, respectively. When the Si{sub 3}N{sub 4} content (m) is higher than 0.27, the emission intensity decreases due to the existence of residual Si{sub 3}N{sub 4} phase. - Highlights: • Addition of Si{sub 3}N{sub 4} can increase the emission intensity of YAG:Ce up to 2.5 times. • Increase in the Ce{sup 3+}/Ce{sup 4+} ratio and the number of Ce-N bonds improve the emission. • The tendency to bond with nitrogen ion for cations in YAG:Ce is (Y, Ce) > Si > Al. • The incomplete dissolution

Calculation of glass forming ranges in Al-Ni-RE (Ce, La, Y) ternary alloys and their sub-binaries based on Miedema's model

International Nuclear Information System (INIS)

Sun, S.P.; Yi, D.Q.; Liu, H.Q.; Zang, B.; Jiang, Y.

2010-01-01

Research highlights: → A method based on semi-empirical Miedema's and Toop's model for predicting glass forming range of ternary alloy system has been systematically described. → The method is superior to conventional models by considering the effect of the thermodynamic asymmetric component when dealing with a ternary alloy system. → The glass forming ranges of Al-Ni-RE (Al-Ni-Ce, Al-Ni-Y and Al-Ni-La) systems and their sub-binaries have been successfully calculated. → The present calculations using the method are in well agreement with experiments. → This model is especially useful for predicting the glass forming range of ternary alloy system because the calculations do not require experimental data. - Abstract: A method based on the semi-empirical Miedema's and Toop's model for calculating the glass forming range of a ternary alloy system was systematically described. The method is superior to conventional models by considering the effect of the thermodynamic asymmetric component when dealing with a ternary alloy system. Using this method, the glass forming ranges of Al-Ni-RE (Ce, La, Y) systems and their sub-binaries were successfully predicted. The mixing enthalpy and mismatch entropy were calculated, and their effects on the glass forming abilities of Al-Ni-RE (Ce, La, Y) systems were also discussed. The glass forming abilities of Al-Ni-Ce, Al-Ni-La and Al-Ni-Y are found to be close. The calculated glass forming ranges agree with experiments well. Meanwhile, the enthalpy change from amorphous phase to solid solution in the glass forming ranges was calculated, and the results suggest that those alloys close to the Ni-RE sub-binary system have higher glass forming abilities.

Luminescence characteristics of Pb2+ centres in undoped and Ce3+-doped Lu3Al5O12 single-crystalline films and Pb2+→Ce3+ energy transfer processes

International Nuclear Information System (INIS)

Babin, V.; Gorbenko, V.; Makhov, A.; Mares, J.A.; Nikl, M.; Zazubovich, S.; Zorenko, Yu.

2007-01-01

At 4.2-350 K, the steady-state and time-resolved emission and excitation spectra and luminescence decay kinetics were studied under excitation in the 2.5-15 eV energy range for the undoped and Ce 3+ -doped Lu 3 Al 5 O 12 (LuAG) single-crystalline films grown by liquid phase epitaxy method from the PbO-based flux. The spectral bands arising from the single Pb 2+ -based centres were identified. The processes of energy transfer from the host lattice to Pb 2+ and Ce 3+ ions and from Pb 2+ to Ce 3+ ions were investigated. Competition between Pb 2+ and Ce 3+ ions in the processes of energy transfer from the LuAG crystal lattice was evidenced especially in the exciton absorption region. Due to overlap of the 3.61 eV emission band of Pb 2+ centres with the 3.6 eV absorption band of Ce 3+ centres, an effective nonradiative energy transfer from Pb 2+ ions to Ce 3+ ions takes place, resulting in the appearance of slower component in the luminescence decay kinetics of Ce 3+ centres and decrease of the Ce 3+ -related luminescence intensity

Dissolution of LnYSiAlO glass (Ln=La or Ce) in aqueous media. Part 3. Influence of β irradiation on structure and hydrolysis mechanisms

International Nuclear Information System (INIS)

Gavarini, S.; Carrot, F.; Trocellier, P.; Boizot, B.; Matzen, G.

2003-01-01

LnYSiAlO glasses (Ln=La or Ce) are considered as potential matrices for the specific storage of minor actinides. β particles emitted during the disintegration of fission products may cause important modifications to the glass network through electronic excitation and ionization. The influence of these processes on the structure of two analogous compositions of glass, involving La or Ce, and the consequences for their chemical durability were studied. Monoliths of glasses were irradiated with electrons that had been accelerated to 2.5 MeV and samples were then leached in static bidistilled water for one month at 90 C. Raman spectrometry, 27 Al MAS-NMR and EPR spectrometry experiments, performed after irradiation, globally indicated weak structural modifications. The two main effects of irradiation were an increase of the (Al IV )/(Al VI +Al V ) ratio and the formation of a paramagnetic center in the case of La-glass (g∼1.99). The former observation could indicate a slight migration and segregation of the rare earth, preferentially surrounded by highly charged Al V and Al VI units initially. The second point could be correlated with a change in the oxidation state of one of the La-glass component. The reason why no similar paramagnetic center is created during irradiation for Ce-glass is not well understood but a possible charge trapping process involving Ce(III)/Ce(IV) is developed. Finally, leaching solution analysis indicated that normalized elemental releases are almost unchanged after irradiation for both of the La and Ce-glass. The globally weak influence of β irradiation on this family of glass is subsequent to the low mobility of the major components that form high field strength bonds with oxygen

Photodynamic processes in LiCaAlF6:Ce3+ UV active medium

International Nuclear Information System (INIS)

Galiev, A I; Semashko, V V; Akhtyamov, O R; Shnaidman, S A; Marisov, M A; Shavelev, A A

2014-01-01

The objectives of this paper are experimental studies of pump-induced effects in LiCaAlF 6 : Ce 3+ single crystals and computer model elaboration and appropriated software package engineering. The elaborated experimental technique and software allow either to calculate the nonlinear absorption/gain characteristics of the active medium on the basis of known parameters, or to find its previously unknown parameters from pump-probe experimental dependences

Luminescence properties of Eu2+- and Ce3+-doped CaAl2S4 and application in white LEDs

International Nuclear Information System (INIS)

Yu Ruijin; Wang Jing; Zhang Jianhui; Yuan Haibin; Su Qiang

2008-01-01

The Eu 2+ - and Ce 3+ -doped CaAl 2 S 4 phosphors were comparatively synthesized by conventional solid-state reaction and the evacuated sealed quartz ampoule. The X-ray diffraction (XRD) patterns show that the sample with better crystalline quality was prepared by the evacuated sealed quartz ampoule, resulting in the enhancement of the emission intensity of Eu 2+ ion by a factor of 1.7. The intensive green LEDs were also fabricated by combining CaAl 2 S 4 :Eu 2+ with near-ultraviolet InGaN chips (λ em =395 nm). The dependence of as-fabricated green LEDs on forward-bias currents shows that it presents good chromaticity stability and luminance saturation, indicating that CaAl 2 S 4 :Eu 2+ is a promising green-emitting phosphor for a near-UV InGaN-based LED. In addition, the optical properties of CaAl 2 S 4 :Ce 3+ were systematically investigated by means of diffuse reflectance, photoluminescence excitation and emission, concentrating quenching and the decay curve. - Graphical abstract: The Eu 2+ - and Ce 3+ -doped CaAl 2 S 4 phosphors were comparatively synthesized by two methods. The emission intensity of Eu 2+ ion in sample synthesized by the evacuated sealed quartz ampoule method is by a factor of 1.7 as strong as that of Eu 2+ ion in sample prepared by the conventional solid-state reaction method

Improve electrochemical performance of CeO2 surface modification LiNi0.80Co0.15Al0.05O2 cathode material

Science.gov (United States)

Xia, Shubiao; Zhang, Yingjie; Dong, Peng; Zhang, Yannan

2014-06-01

Lithium ion battery cathode material LiNi0.8Co0.15Al0.05O2 cathode has successfully prepared by co-precipitation. CeO2 surface modification has improved LiNi0.80Co0.15Al0.05O2 electrochemical performance use sol-gel method and subsequent heat treatment at 600 °C for 5 h. Different to other conventional coating material, CeO2 coating layer can not only inhibit the reaction of the electrode and the electrolyte, but also can reduce the impedance of electron transfer due to its high conductivity, and inhibit the production of Ni2+ because of its high oxidation. The surface-modified and pristine LiNi0.80Co0.15Al0.05O2 powders are characterized by XRD, SEM, TEM, XPS, CV and DSC. When CeO2 coating is 0.02% (mole ratio), contrast to pristine NCA, the CeO2-coated NCA cathode exhibits no decrease in its initial specific capacity of 184 mAh g -1 (at 0.2 C) and excellent capacity retention (86% of its initial capacity at 1 C) between 2.75 and 4.3 V after 100 cycles. The results indicate that the CeO2 surface treatment should be an effective way to improve cycle properties due to CeO2 inhibit the electrodes and the electrolyte side effects.

Preparation and characterization of Au/CeO{sub 2}-Al{sub 2}O{sub 3} monoliths

Energy Technology Data Exchange (ETDEWEB)

Gawel, Bartlomiej; Lambrechts, Kalle [Ugelstad Laboratory, Department of Chemical Engineering, Norwegian University of Science and Technology (NTNU), N-7491 Trondheim (Norway); Oye, Gisle, E-mail: gisle.oye@chemeng.ntnu.no [Ugelstad Laboratory, Department of Chemical Engineering, Norwegian University of Science and Technology (NTNU), N-7491 Trondheim (Norway)

2012-05-15

Highlights: Black-Right-Pointing-Pointer A facile method for preparing Au/CeO{sub 2}-Al{sub 2}O{sub 3} monoliths with hierarchical porosity. Black-Right-Pointing-Pointer Continuous-flow testing of the monoliths in liquid-phase oxidation of glucose. Black-Right-Pointing-Pointer Increased catalytic activity in the presence of cerium oxide (stirred-batch tests). - Abstract: Porous CeO{sub 2}-Al{sub 2}O{sub 3} monoliths with hierarchical pore structure were prepared by mixing boehmite particles with solutions containing different amounts of cerium chloride and aluminum nitrate. The monoliths were functionalized with gold nanoparticles using the incipient wetness method. The resulting materials were characterized by X-ray diffraction, nitrogen sorption, mercury porosimetry, UV-vis spectroscopy and transmission electron microscopy. The catalysts were tested in liquid phase glucose oxidation, comparing continuously stirred batch reactor and continuous-flow fix-bed reactor setups.

Luminescence properties of Ce3+ and Tb3+ co-activated ZnAl2O4 phosphor

International Nuclear Information System (INIS)

Tshabalala, K.G.; Cho, S.-H.; Park, J.-K.; Pitale, Shreyas S.; Nagpure, I.M.; Kroon, R.E.; Swart, H.C.; Ntwaeaborwa, O.M.

2012-01-01

In this study, a solution combustion method was used to prepare green emitting Ce 3+ –Tb 3+ co-activated ZnAl 2 O 4 phosphor. The samples were annealed at 700 °C in air or hydrogen atmosphere to improve their crystallinity and optical properties. X-ray diffraction study confirmed that both as-prepared and post-preparation annealed samples crystallized in the well known cubic spinel structure of ZnAl 2 O 4 . An agglomeration of irregular platelet-like particles whose surfaces were encrusted with smaller spheroidal particles was confirmed by scanning electron microscopy (SEM). The fluorescence data collected from the annealed samples with different concentrations of Ce 3+ and Tb 3+ show the enhanced green emission at 543 nm associated with 5 D 4 → 7 F 5 transitions of Tb 3+ . The enhancement was attributed to energy transfer from Ce 3+ to Tb 3+ . Possible mechanism of energy transfer via a down conversion process is discussed. Furthermore, cathodoluminescence (CL) intensity degradation of this phosphor was also investigated and the degradation data suggest that the material was chemically stable and the CL intensity was also stable after 10 h of irradiation by a beam of high energy electrons.

El nuevo régimen de las operaciones vinculadas

Directory of Open Access Journals (Sweden)

Pedro Rosón Silván

2011-06-01

Full Text Available El nuevo y polémico régimen fiscal de operaciones vinculadas supone un cambio radical respecto de la regulación anterior a la Ley de Prevención del Fraude Fiscal de 2006, y pretende aproximar la normativa fiscal a los criterios expresados por las directrices de la OCDE sobre precios de transferencia, y a la nueva normativa contable, que se inspira en las Normas Internacionales de Contabilidad asumidas por la Unión Europea. Los principales cambios han afectado no solo al concepto de partes vinculadas (que se ha ampliado o la incorporación de los métodos de valoración de la OCDE, sino, sobre todo a: 1.La creación de una nueva obligación de documentación a cargo del obligado tributario que tiene que valorar sus operaciones a valor de mercado; 2.La creación de dos nuevas infracciones tributarias, para asegurar el cumplimiento de la obligación de documentación; 3.La simplificación del procedimiento de comprobación del valor normal de mercado; 4.La regulación expresa del denominado ajuste secundario. Pese a su novedad y por las presiones de los afectados, se han producido reformas para rebajar tanto las obligaciones de documentación como las sanciones, y, todo hace pensar que dado el contexto de crisis económica, puedan producirse más. The new and polemic fiscal regime of linked operations a radical change supposes respect of the regulation previous to the Law of Prevention of the Tax evasion of 2006, and tries to bring the fiscal regulation near to the criteria expressed by the directives of the OECD on prices of transfer, and to the new countable regulation, which inspires by the International Procedure of Accounting assumed by the European Union. The principal changes have concerned not only the concept of parts linked (that has been extended or the incorporation of the methods of valuation of the OECD, but, especially to: 1.The creation of a new obligation of documentation at the expense of the obliged tributary who has to

Multi-component Ce doped (Gd,Y,La,Lu)3(AlGaSc)5O12 garnets – A new story in the development of scintillating single crystalline film screens

International Nuclear Information System (INIS)

Zorenko, Yu.; Gorbenko, V.; Savchyn, V.; Zorenko, T.; Fedorov, A.; Wrzesinski, H.; Vasylkiv, Ya.

2013-01-01

The paper is dedicated to development of the scintillators based on single crystalline films of Ce doped (GdLaYLu) 3 (AlGaSc) 5 O 12 multi-component garnets onto Gd 3 Ga 5 O 12 substrates using the liquid phase epitaxy method. -- Highlights: •Growth of Ce doped (GdYLaLu) 3 (AlGaSc) 5 O 12 garnets films by LPE method. •Luminescent and scintillation properties of Ce doped (GdYLaLu) 3 (AlGaSc) 5 O 12 films. •Influence of Pb 2+ flux related impurity on the light yield of Ce 3+ emission

Tuning Ce distribution for high performanced Nd-Ce-Fe-B sintered magnets

Energy Technology Data Exchange (ETDEWEB)

Fan, Xiaodong [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China); Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Science, Ningbo 315201 (China); Guo, Shuai; Chen, Kan; Chen, Renjie; Lee, Don [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Science, Ningbo 315201 (China); You, Caiyin, E-mail: caiyinyou@xaut.edu.cn [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China); Yan, Aru, E-mail: aruyan@nimte.ac.cn [Key Laboratory of Magnetic Materials and Devices, Ningbo Institute of Material Technology and Engineering, Chinese Academy of Science, Ningbo 315201 (China)

2016-12-01

A dual-alloy method was applied to tune the distribution of Ce for enhancing the performance of Nd-Ce-Fe-B sintered magnets with a nominal composition of (Nd{sub 0.75}Ce{sub 0.25}){sub 30.5}Fe{sub bal}Al{sub 0.1}Cu{sub 0.1}B. In comparison to the single alloy of (Nd{sub 0.75}Ce{sub 0.25}){sub 30.5}Fe{sub bal}Al{sub 0.1}Cu{sub 0.1}B, the coercivity was enhanced from 10.3 kOe to 12.1 kOe and the remanence was increased from 13.1 kG to 13.3 kG for the magnets with a dual-alloy method. In addition, the remanence temperature coefficient α and coercivity temperature coefficient β were also slightly improved for the magnet with the dual alloys. The results of microstructure characterizations show the uniform distribution of Ce for the magnet with a single alloy, and the coexistence of the Ce-rich and Ce-lean regions for the magnet with the dual alloys. In combinations with the nucleation of reversal domains and magnetic recoil curves, the property enhancement of magnets with a dual-alloy method was well explained. - Highlights: • Improved magnetic properties were obtained in dual-alloy magnet. • This is due to the tuning of Ce distribution and the change in microstructure. • The magnetic hardening effect can be observed in dual-alloy magnet.

Development and characterization of nickel catalysts supported in CeO2-ZrO2-Al2O3, CeO2-La2O3-Al2O3 e ZrO2-La2O3-Al2O3 matrixes evaluated for methane reforming reactions

International Nuclear Information System (INIS)

Abreu, Amanda Jordão de

2012-01-01

Nowadays, the methane reforming is large interest industrial for the take advantage of these gas in production the hydrogen and synthesis gas (syngas). Among in the reactions of methane stand of the reactions steam reforming and carbon dioxide reforming of methane. The main catalysts uses in the methane reforming is Ni/Al 2 O 3 . However, the supported-nickel catalyst is susceptible to the deactivation or the destruction by coke deposition. The carbon dissolves in the nickel crystallite and its diffuses through the nickel, leading for formation of the carbon whiskers, which results in fragmentation of the catalyst. Modification of such catalysts, like incorporation of suitable promoters, is desirable to achieve reduction of the methane hydrogenolysis and/or promotion of the carbon gasification. Catalysts 5%Ni/Al 2 O 3 supported on solid solutions formed by ZrO 2 -CeO 2 , La 2 O 3 and CeO 2 -ZrO 2 -La 2 O 3 were prepared, characterized and evaluated in reactions steam and carbon dioxide reforming and partial oxidation of methane with objective the value effect loading solution solid in support. The supports were prepared by co-precipitation method and catalysts were prepared by impregnation method and calcined at 500 deg C. The supports and catalysts were characterized by Nitrogen Adsorption, method -rays diffraction (XRD), X-rays dispersive spectroscopy (XDS), spectroscopy in the region of the ultraviolet and the visible (UV-vis NIR) to and temperature programmed reduction (TPR), Raman Spectroscopy, X-ray absorption spectroscopy and Thermogravimetric Analysis. After all the catalytic reactions check which the addition of solid solution is beneficial for Ni/Al 2 O 3 catalysts and the best catalysts are Ni/CeO 2 -La 2 O 3 -Al 2 O 3 . (author)

Synthesis and luminescence properties of Ce{sup 3+}-doped Y{sub 3}Al{sub 3.5}Ga{sub 1.5}O{sub 12} green phosphor for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Qiang, Yaochun [Fujian Key Laboratory of Advanced Materials, Department of Materials Science and Engineering, College of Materials, Xiamen University, Xiamen 361005 (China); Yu, Yuxi, E-mail: yu_heart@xmu.edu.cn [Fujian Key Laboratory of Advanced Materials, Department of Materials Science and Engineering, College of Materials, Xiamen University, Xiamen 361005 (China); Chen, Guolong [Fujian Engineering Research Center for Solid-state Lighting, Department of Electronic Science, Xiamen University, Xiamen 361005 (China); Fang, Jiyu [Advanced Materials Processing and Analysis Center, Department of Materials Science and Engineering, University of Central Florida, Orlando, FL 32816 (United States)

2016-04-15

A series of Ce{sup 3+}-doped Y{sub 3}Al{sub 3.5}Ga{sub 1.5}O{sub 12} green phosphors were successfully synthesized by a solid-state reaction method. The microstructure, morphology, luminescence spectra, luminescence quantum yield (QY) and thermal stability of the phosphor were investigated. The critical concentration of Ce{sup 3+} ions in Y{sub 3−m}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:mCe{sup 3+} is m=0.06. The QY of Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} phosphor is as high as 94% under excitation at 450 nm and its luminescence intensity at 150 °C still maintains 90% of that measured at 25 °C, which are just a little worse than those of commercial Lu{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} green phosphor but much better than those of commercial (Sr,Ba){sub 2}SiO{sub 4}:Eu{sup 2+} green phosphor. A white LED lamp was fabricated by employing Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} as a green phosphor and commercial (Ca,Sr)AlSiN{sub 3}:Eu{sup 2+} as a red phosphor (628 nm), its Ra value, correlated color temperature (CCT), CIE1931 chromaticity coordinates and luminous efficiency is 84, 3081 K, (x=0.4369, y=0.4142) and 102 lm/W, respectively. The experimental results demonstrate that Y{sub 2.94}Al{sub 3.5}Ga{sub 1.5}O{sub 12}:0.06Ce{sup 3+} is a promising green phosphor not only can be used for high color rendering index white LEDs but also for high-power white LEDs.

Synthesis and characterization of molybdenum catalysts supported on {gamma}-Al{sub 2}O{sub 3}-CeO{sub 2} composite oxides

Energy Technology Data Exchange (ETDEWEB)

Farooq, Muhammad; Ramli, Anita; Subbarao, Duvvuri [Department of Chemical EngineeringUniversiti Teknologi PETRONAS Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia); Fundamental and Applied Sciences Department, Universiti Teknologi PETRONAS Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia); Department of Chemical EngineeringUniversiti Teknologi PETRONAS Bandar Seri Iskandar, 31750 Tronoh, Perak (Malaysia)

2012-09-26

The physical and chemical properties of a catalyst play a vital role in various industrial applications. Molybdenum catalysts supported on {gamma}-Al{sub 2}O{sub 3} and {gamma}-Al{sub 2}O{sub 3}-CeO{sub 2} mixed oxides with varying loading of CeO{sub 2} (5, 10, 15, 20 wt% with respect to {gamma}-Al{sub 2}O{sub 3}) were prepared by wet impregnation method. The physiochemical properties of these synthesized Mo catalysts were studied with various characterization techniques such as X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature-programmed reduction (TPR), field emission scanning electron microscopy-energy dispersive analysis (FESEM-EDX) and X-ray fluorescence spectrometer (XRF). The results showed that the addition of CeO{sub 2} into the support affected the binding energies of the elements and reducibility of the metal oxides formed after calcination of catalyst samples due to the change in metal-support interaction. Further, the characterization techniques showed that the active metal was well dispersed on the surface of support material.

Microstructural characterization of a rapidly solidified ultrahigh strength Al94.5Cr3Co1.5Ce1 alloy

International Nuclear Information System (INIS)

Ping, D.H.; Hono, K.; Inoue, A.

2000-01-01

The microstructure of a rapidly solidified Al 94.5 Cr 3 Co 1.5 Ce 1 alloy has been examined in detail by means of high resolution transmission electron microscopy (HRTEM) and atom probe field ion microscopy (APFIM). In the as-quenched microstructure, nanoscale particles of a solute-enriched amorphous phase and an Al-Cr compound are dispersed in randomly oriented fine grains of α-Al ( 200nm ). The interface between the Al grains and the amorphous particles is not smooth but irregular with atomic protrusions and concavities, suggesting that interfacial instability occurs during the solidification process. Nanoscale amorphous particles are formed as a result of solute trapping within the rapidly grown Al grains. After annealing at 400 C for 15 minutes grain growth occurs, and the interface of the Al grains is smoothed. The amorphous region trapped within the grains if crystallized to an Al-Cr compound, but no icosahedral phase has been confirmed. The APFIM results have revealed that Cr and Ce atoms have a similar partitioning behavior, i.e., they are rejected from the α-Al phase and partitioned into the trapped amorphous regions. On the other hand, Co atoms are not partitioned between the two phases in the as-quenched state but are partitioned into the α-Al grains in the annealed alloys being rejected from the Al compounds and finally form Al-Co compounds. Based on these microstructural characterization results, the origins of high strength of this alloy are discussed

Luminescence of Ce3+ ions in Y3Al5O12 - Y3Ga5O12 solid solution

International Nuclear Information System (INIS)

Zorenko, Yu.V.; Nazar, I.V.; Limarenko, L.N.; Pashkovskij, M.V.

1996-01-01

Regularities of changes in spectral and energetic characteristics of the Ce 3+ ions radiation in the Y 3 Al 5-x Ga x O 12 solid solutions, related to change in the matrix crystal field force and dissipation of the luminescence excitation energy because of transfers between the valency zone ceiling and the Ce 3+ excited ion basis state are obtained. 9 refs., 3 figs., 1 tab

Effect of Al/Ga substitution on the structural and luminescence properties of Y3(Al1-xGax)5O12: Ce3+ phosphors

Science.gov (United States)

Fu, Sheng; Tan, Jin; Bai, Xin; Yang, Shanjie; You, Lei; Du, Zhengkang

2018-01-01

As candidates for display and lighting materials, a series of gallium-substituted cerium-doped yttrium aluminum garnet (Y3(GaxAl1-x)5O12: Ce3+) phosphors were synthesized by high temperature solid-state reaction. The phases, morphology, luminescence spectra and thermal stability of the phosphors were investigated. The volatilization of Ga2O3 induces the constituents out of stoichiometric ratio and different impurities in the system. The excitation and emission spectra occur red shift (339 nm - 351 nm) and blue shift (465 nm - 437 nm), and blue shift (541 nm - 517 nm), respectively. The spectra have no further blue shift and the luminescence intensity decrease with x over 0.4. Combining crystal structure with PL spectrum, the distortion of dodecahedron and crystal field splitting of 5d level of Ce3+ are influenced by Ga3+ in octahedral coordination polyhedron rather than tetrahedron. The crystalline perfection and Ga3+ occupying the tetrahedron induce less garnet phase formation, more impurities and the 5d level located in the conductive bands, thus accounting for the x = 0.4 turning points of the PL and PLE intensity. Based on the thermal quenching and CIE, the Y3(GaxAl1-x)5O12: Ce3+0.06 phosphors have great potential for use on the w-LED.

Thermoluminescence of LaAlO3 crystals doped with Eu and Ce - Dy ions exposed to ultraviolet and gamma radiation

International Nuclear Information System (INIS)

Oliveira, Vitor H.; Faria, Luiz O.; Silva, Edna S.

2011-01-01

Due to environmental problems such as degradation of the ozone layer and control of radiation levels in units of radiation, new dosimetric materials with high sensitivity for ultraviolet (UV) and gamma radiation are of great interest for applications in environmental dosimetry. In this context, this paper presents the results of a systematic investigation of the thermoluminescent (TL) response of LaAlO 3 crystals doped with different concentrations of trivalent optically active ions exposed to UV and gamma radiation doses. The work has been performed under a direct cooperation between the Institute of Inorganic Chemistry in Moscow (IGIC), responsible for crystal growth, and the Center for Development of Nuclear Technology (CDTN), responsible for the study of its luminescent properties. In this context, samples doped with 1% of Eu 3+ , 1% Ce 3+ , 5% of Ce 3+ and also co-doped with 5% Ce 3+ and 1% Dy 3+ were grown under hydrothermal conditions. The investigation was divided into two fronts, one for gamma radiation and the other for UV radiation. In the investigation with gamma radiation the best TL response has been obtained from LaAlO 3 :Eu. This crystal has shown good sensitivity and excellent linearity between TL output and the delivered gamma doses ranging from 0.1 to 10.0 mGy. In addition, its TL curve is quite similar to the Al 2 O 3 :C, a commercial TL phosphor with high sensitivity to gamma radiation. In the investigation with UV radiation the best response has been achieved for co-doped LaAlO 3 :Ce,Dy. They have excellent sensitivity and good linearity for spectral irradiances ranging from 0.042 to 1.2 mJ.cm -2 . (author)

Comparing the dynamic and thermodynamic behaviors of Al{sub 86}Ni{sub 9}-La{sub 5}/(La{sub 0.5}Ce{sub 0.5}){sub 5} amorphous alloys

Energy Technology Data Exchange (ETDEWEB)

Li, G.H. [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China); Wang, W.M. [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)], E-mail: weiminw@sdu.edu.cn; Bian, X.F.; Zhang, J.T.; Li, R.; Wang, L. [Key Laboratory of Liquid Structure and Heredity of Materials, Ministry of Education, Shandong University, Jinan 250061 (China)

2009-06-10

The dynamic viscosities and thermodynamic dilatometric behaviors of Al{sub 86}Ni{sub 9}La{sub 5} and Al{sub 86}Ni{sub 9}(La{sub 0.5}Ce{sub 0.5}){sub 5} amorphous alloys were investigated using viscometer, differential scanning calorimetry (DSC) and conventional dilatometer. Comparing with Al{sub 86}Ni{sub 9}La{sub 5} alloy, Al{sub 86}Ni{sub 9}(La{sub 0.5}Ce{sub 0.5}){sub 5} alloy exhibits a larger viscosity and a larger average thermal expansion coefficient in the linear expansion zone ({alpha}{sub exp}). The viscosity and thermal expansion data suggest that the partial substitution La by Ce decreases the quantity of free volume in Al-Ni-La system by improving the continuous degree of atomic size, which leads to the improvement of glass forming ability.

Preparation and visible light responsive photocatalytic activity of Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites

Energy Technology Data Exchange (ETDEWEB)

Hao, Jiaqi; Qu, Ting; Wang, Qiufeng; Zhao, Zhenbo, E-mail: zhaozhenbo@ccut.edu.cn [School of Chemistry and Life Science, Changchun University of Technology, Changchun, Jilin (China)

2017-09-15

Novel Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites were prepared through a hydrothermal method and co-precipitation method. The morphologies and structures of the photocatalysts were characterized by XRD, Raman, TEM, UV-vis-DRS, BET surface area and VSM techniques. The photocatalytic performances of the photocatalysts were investigated by the decolorisation of methyl orange (MO) under visible-light irradiation. The results showed that the Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites exhibited greater photocatalytic activities compared to pure Bi{sub 2}WO{sub 6} and the Ni-Al-Ce LDH; the decolorisation rate of MO was 87% within 60 min under visible-light irradiation. The decolorisation efficiency of the composite material remained at 71% after 4 recycling runs, showing improved stability. Furthermore, the experimental results also showed that the photocatalytic reactions for the composites followed first-order reaction kinetics. Therefore, the Fe{sub 3}O{sub 4}/Ni-Al-Ce LDH/Bi{sub 2}WO{sub 6} composites were photocatalysts with high efficiencies and stabilities for a photocatalytic reaction of an organic pollutant, and this study provides a new, effective method for the development of wastewater treatment. (author)

Quasiparticle band structure for the Hubbard systems: Application to α-CeAl2

International Nuclear Information System (INIS)

Costa-Quintana, J.; Lopez-Aguilar, F.; Balle, S.; Salvador, R.

1990-01-01

A self-energy formalism for determining the quasiparticle band structure of the Hubbard systems is deduced. The self-energy is obtained from the dynamically screened Coulomb interaction whose bare value is the correlation energy U. A method for integrating the Schroedingerlike equation with the self-energy operator is given. The method is applied to the cubic Laves phase of α-CeAl 2 because it is a clear Hubbard system with a very complex electronic structure and, moreover, this system provides us with sufficient experimental data for testing our method

Study on preparation of orange-emitting phosphor Y3Mg2AlSi2O12: Ce3+ for wLED

Directory of Open Access Journals (Sweden)

Yan Shirun

2017-12-01

Full Text Available Ce3+-doped garnet-structured orange-emitting phosphor Y3Mg2AlSi2O12:Ce3+ was prepared by sol-gel combustion using urea as a fuel.Effects of the reduction temperature,Ce3+ doping concentration on the structure,morphology,and photoluminescence property of the as-prepared phosphor were investigated by X-ray diffraction(XRD,scaning electron microscope(SEM,photoluminescence spectroscopy and UV-Vis reflection spectroscopy.The crystallinities,morphologies,and photoluminescence properties of the phosphors prepared by sol-gel combustion and solid-state reaction were compared.The reasons causing different performance of the phosphors were discussed.

Arcillas pilarizadas con Al-Fe y Al-Ce-Fe como sistema de postratamiento de las aguas residuales del beneficio húmedo del café

OpenAIRE

Peralta Ladino, Yury Marlén

2013-01-01

El efluente del sistema de tratamiento biológico de las aguas residuales del beneficio húmedo del café contiene compuestos no biodegradables, principalmente (ácidos hidroxicinámicos y clorogénicos) los cuales fueron identificados mediante análisis preliminares por LC-MS, por su toxicidad deben ser tratados antes de su descarga en las fuentes hídricas. El sistema Fenton heterogéneo empleando como soportes Al-Fe-PILC y Al-Ce-Fe-PILC (en polvo) mostró importantes conversión de compuestos fenólic...

Photoluminescence properties of Tb3Al5O12:Ce3+ garnet synthesized by the metal organic decomposition method

Science.gov (United States)

Onishi, Yuya; Nakamura, Toshihiro; Adachi, Sadao

2017-02-01

Tb3Al5O12:Ce3+ garnet (TAG:Ce3+) phosphor was synthesized by the metal organic decomposition (MOD) method and subsequent calcination at Tc = 800-1200°C for 1 h in air. The effects of Ce3+ concentration on the phosphor properties were investigated in detail using X-ray diffraction (XRD) analysis, photoluminescence (PL) analysis, PL excitation (PLE) spectroscopy, and PL decay measurements. The maximum intensity in the Ce3+ yellow emission was observed at the Ce3+ concentration of ∼0.20%. PLE and PL decay measurements suggested an evidence of the energy transfer from Tb3+ to Ce3+. Calcination temperature dependence of the XRD and PL intensities yielded an energy of ∼1.5 eV both for the TAG formation in the MOD process and for the optical activation of Ce3+ in its lattice sites. Temperature dependences of the PL intensity for the TAG:Ce3+ yellow-emitting and K2SiF6:Mn4+ red-emitting phosphors were also examined for the future solid-state lighting applications at T = 20-500 K in 10-K steps. The data of TAG:Ce3+ were analyzed using a theoretical model with considering a reservoir level of Et ∼9 meV, yielding a quenching energy of Eq ∼0.35 eV, whereas the K2SiF6:Mn4+ red-emitting phosphor data yielded a value of Eq ∼1.0 eV. The schematic energy-level diagrams for Tb3+ and Ce3+ were proposed for the sake of a better understanding of these ions in the TAG host.

Thermoluminescence of LaAlO{sub 3} crystals doped with Eu and Ce - Dy ions exposed to ultraviolet and gamma radiation

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Vitor H.; Faria, Luiz O., E-mail: farialo@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Silva, Edna S. [Universidade Federal de Minas Gerais (DEN/UFMG), Belo Horizonte, MG (Brazil). Dept. de Energia Nuclear; Khaidukov, Nicholas M. [Kurnakov Institute of General and Inorganic Chemistry, IGIC, Moscow (Russian Federation)

2011-07-01

Due to environmental problems such as degradation of the ozone layer and control of radiation levels in units of radiation, new dosimetric materials with high sensitivity for ultraviolet (UV) and gamma radiation are of great interest for applications in environmental dosimetry. In this context, this paper presents the results of a systematic investigation of the thermoluminescent (TL) response of LaAlO{sub 3} crystals doped with different concentrations of trivalent optically active ions exposed to UV and gamma radiation doses. The work has been performed under a direct cooperation between the Institute of Inorganic Chemistry in Moscow (IGIC), responsible for crystal growth, and the Center for Development of Nuclear Technology (CDTN), responsible for the study of its luminescent properties. In this context, samples doped with 1% of Eu{sup 3+}, 1% Ce{sup 3+}, 5% of Ce{sup 3+} and also co-doped with 5% Ce{sup 3+} and 1% Dy{sup 3+} were grown under hydrothermal conditions. The investigation was divided into two fronts, one for gamma radiation and the other for UV radiation. In the investigation with gamma radiation the best TL response has been obtained from LaAlO{sub 3}:Eu. This crystal has shown good sensitivity and excellent linearity between TL output and the delivered gamma doses ranging from 0.1 to 10.0 mGy. In addition, its TL curve is quite similar to the Al{sub 2}O{sub 3}:C, a commercial TL phosphor with high sensitivity to gamma radiation. In the investigation with UV radiation the best response has been achieved for co-doped LaAlO{sub 3}:Ce,Dy. They have excellent sensitivity and good linearity for spectral irradiances ranging from 0.042 to 1.2 mJ.cm{sup -2}. (author)

Effects of flux additives on the characteristics of Y2.95Al5O12:0.05Ce3+ phosphor: Particle growth mechanism and luminescence

International Nuclear Information System (INIS)

Chiang, Chung-Hao; Liu, Te-Hsing; Lin, Han-Yu; Kuo, Hung-Yi; Chu, Sheng-Yuan

2013-01-01

The dependence of the amount of the BaF 2 flux additive on the luminescence of Y 2.95 Al 5 O 12 :0.05Ce 3+ phosphors was investigated. The integrated emission intensity of Y 2.95 Al 5 O 12 :0.05Ce 3+ prepared without the flux was enhanced by 29% with the addition of BaF 2 flux at the optimum amount of 6 wt. %. Such an enhancement can be attributed to the purer phase of Y 3 Al 5 O 12 and the morphology change from the irregular shape to spherical shape with the smoother surface due to the flux. The morphology and luminescence of Y 2.95 Al 5 O 12 :0.05Ce 3+ prepared with the 6 wt. % BaF 2 flux additive (Sample II) were further compared with those of Y 2.95 Al 5 O 12 :0.05Ce 3+ prepared with the 7 wt. % H 3 BO 3 flux additive (Sample I). The particle size, particle shape, and integrated emission intensity (λ ex  = 450 nm) of the former were found to be larger, more regular, and 6% higher than those of the latter. The difference in the morphology of Samples I and II, which led to the difference in the emission intensity and the external quantum efficiency, were well explained by the particle growth mechanism

Behaviour of LaAlO 3 +LnTiTaO 6 (Ln= Ce, Pr or Nd)

Indian Academy of Sciences (India)

The 0.1LaAlO3+0.9LnTiTaO6 (Ln= Ce, Pr or Nd) ceramics are prepared through solid state ceramic route. The structure of the materials is studied using X-ray diffraction analysis. The microstructure is analysed using scanning electron microscopy. The dielectric properties in the radio as well as in the microwave frequencies ...

Mechanical properties of a high-strength Al{sub 90}Mn{sub 8}Ce{sub 2} alloy

Energy Technology Data Exchange (ETDEWEB)

Li, J.C.; Zhao, Z.K.; Jiang, Q. [Key Laboratory of Automobile Materials, Ministry of Education and Department of Materials Science and Engineering, Jilin University, Changchun 130025 (China)

2003-03-01

A lightweight alloy with excellent strength and wear resistance, Al{sub 90}Mn{sub 8}Ce{sub 2}, has been manufactured in bulk by powder metallurgy. The best colligative mechanical properties of the alloy made by this technique are achieved by pressing at 753 K, where the porosity reaches a minimum, and the plasticity a maximum. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Low-density to high-density transition in Ce75Al23Si2 metallic glass

International Nuclear Information System (INIS)

Zeng, Q S; Lou, H B; Gong, Y; Wang, X D; Jiang, J Z; Fang, Y Z; Wu, F M; Yang, K; Li, A G; Yan, S; Yu, X H; Lathe, C

2010-01-01

Using in situ high-pressure x-ray diffraction (XRD), we observed a pressure-induced polyamorphic transition from the low-density amorphous (LDA) state to the high-density amorphous (HDA) state in Ce 75 Al 23 Si 2 metallic glass at about 2 GPa and 300 K. The thermal stabilities of both LDA and HDA metallic glasses were further investigated using in situ high-temperature and high-pressure XRD, which revealed different pressure dependences of the onset crystallization temperature (T x ) between them with a turning point at about 2 GPa. Compared with Ce 75 Al 25 metallic glass, minor Si doping shifts the onset polyamorphic transition pressure from 1.5 to 2 GPa and obviously stabilizes both LDA and HDA metallic glasses with higher T x and changes their slopes dT x /dP. The results obtained in this work reveal another polyamorphous metallic glass system by minor alloying (e.g. Si), which could modify the transition pressure and also properties of LDA and HDA metallic glasses. The minor alloying effect reported here is valuable for the development of more polyamorphous metallic glasses, even multicomponent bulk metallic glasses with modified properties, which will trigger more investigations in this field and improve our understanding of polyamorphism and metallic glasses.

A computational study of magnetic exchange interactions of 3d and 4f electrons in Ti-Ce co-doped AlN

Energy Technology Data Exchange (ETDEWEB)

Majid, Abdul, E-mail: abdulmajid40@yahoo.com [Department of Physics, University of Gujrat, Gujrat (Pakistan); Department of Adaptive Machine Systems, Osaka University, Osaka (Japan); Azmat, Mian [Department of Physics, University of Gujrat, Gujrat (Pakistan); Rana, Usman Ali; Khan, Salah Ud-Din [Sustainable Energy Technologies Center, College of Engineering, King Saud University, PO-Box 800, Riyadh 11421 (Saudi Arabia); Alzahrani, Eman [Department of Chemistry, Faculty of Science, Taif University, 888 Taif (Saudi Arabia)

2016-08-15

To investigate the nature of 3d-4f exchange interactions in III-Nitride semiconductors, Ti-Ce co-doped AlN were studied using first principles calculations. The calculations were performed using supercell approach with varying dopant concentration and different inter-dopant separation. The configuration with dopant located as nearest neighbor distance and diluted concentration of 3.125% was found most stable. The results exhibited prominent evidence of 3d-4f-5d strong hybridization suggesting 3d-4f direct exchange interactions which may play valuable role to exploit the system as high Curie temperature ferromagnetic semiconductors for use in spintronics. Moreover, metal to metal charge transfer was also observed in the materials which may be exploited for their use in electrochemical applications. The 4f-5d and 3d-5d hybridizations were observed that predicts excellent luminescence phenomena in the materials. The presence of impurity related deep intermediate bands suggest applications of the materials in opto-electronic and spintronics devices. - Highlights: • Double exchange interaction in Ti:AlN. • Impurity induced narrowing of band gap. • Superexchange interaction in Ce:AlN. • 3d-4f exchange interaction between Ti-3d and Ce-4f states. • High Curie temperature n-type ferromagnetic semiconductors.

A computational study of magnetic exchange interactions of 3d and 4f electrons in Ti-Ce co-doped AlN

International Nuclear Information System (INIS)

Majid, Abdul; Azmat, Mian; Rana, Usman Ali; Khan, Salah Ud-Din; Alzahrani, Eman

2016-01-01

To investigate the nature of 3d-4f exchange interactions in III-Nitride semiconductors, Ti-Ce co-doped AlN were studied using first principles calculations. The calculations were performed using supercell approach with varying dopant concentration and different inter-dopant separation. The configuration with dopant located as nearest neighbor distance and diluted concentration of 3.125% was found most stable. The results exhibited prominent evidence of 3d-4f-5d strong hybridization suggesting 3d-4f direct exchange interactions which may play valuable role to exploit the system as high Curie temperature ferromagnetic semiconductors for use in spintronics. Moreover, metal to metal charge transfer was also observed in the materials which may be exploited for their use in electrochemical applications. The 4f-5d and 3d-5d hybridizations were observed that predicts excellent luminescence phenomena in the materials. The presence of impurity related deep intermediate bands suggest applications of the materials in opto-electronic and spintronics devices. - Highlights: • Double exchange interaction in Ti:AlN. • Impurity induced narrowing of band gap. • Superexchange interaction in Ce:AlN. • 3d-4f exchange interaction between Ti-3d and Ce-4f states. • High Curie temperature n-type ferromagnetic semiconductors.

Novel Ni-Ce-Zr/Al2O3 Cellular Structure for the Oxidative Dehydrogenation of Ethane

Directory of Open Access Journals (Sweden)

Juan Pablo Bortolozzi

2017-11-01

Full Text Available A novel γ-alumina-supported Ni-Ce-Zr catalyst with cellular structure was developed for oxidative dehydrogenation of ethane (ODHE. First, powdered samples were synthesized to study the effect of both the total metal content and the Ce/Zr ratio on the physicochemical properties and performance of these catalysts. All synthesized powdered samples were highly active and selective for ODHE with a maximum ethylene productivity of 6.94 µmolethylene gact cat−1 s−1. According to the results, cerium addition increased the most reducible nickel species population, which would benefit ethane conversion, whereas zirconium incorporation would enhance ethylene selectivity through the generation of higher amounts of the least reducible nickel species. Therefore, the modification of active site properties by addition of both promoters synergistically increases the productivity of the Ni-based catalysts. The most efficient formulation, in terms of ethylene productivity per active phase amount, contained 15 wt% of the mixed oxide with Ni0.85Ce0.075Zr0.075 composition. This formulation was selected to synthesize a Ni-Ce-Zr/Al2O3 structured body by deposition of the active phase onto a homemade γ-alumina monolith. The structured support was manufactured by extrusion of boehmite-containing dough. The main properties of the Ni0.85Ce0.075Zr0.075 powder were successfully preserved after the shaping procedure. In addition, the catalytic performance of the monolithic sample was comparable in terms of ethylene productivity to that of the powdered counterpart.

Unstable magnetic moments in Ce compounds

International Nuclear Information System (INIS)

Aarts, J.

1984-01-01

The problems which are connected with the appearance or disappearance of local moments in metals are well reflected in the magnetic behaviour of Ce intermetallic compounds. This work describes experiments on two Ce compounds which are typical examples of unstable moment systems. The first of these is CeAl 2 which at low temperatures, shows coexistence of antiferromagnetic order and the Kondo effect. Measurements are presented of the magnetization and the susceptibility in different magnetic field and temperature regions. An analysis of these measurements, using a model for the crystal field effects, shows the agreement between the measurements and the calculations to be reasonably good for CeAl 2 , but this agreement becomes worse upon decreasing Ce concentration. A phenomenological description of the observations is given. The second compound reported on is CeCu 2 Si 2 , the first 'heavy-fermion' superconductor to be investigated. The superconducting state is possibly formed by the quasi-particles of a non-magnetic many body singlet state, and not simply by the (sd) conduction electrons. This being a novel phenomenon, a number of experiments were performed to test this picture and to obtain a detailed description of the behaviour of CeCu 2 Si 2 . Measurements of the Meissner volume, confirmed the superconductivity to be intrinsic. (Auth.)

Tuning the hybridization and magnetic ground state of electron and hole doped CeOs2Al10 : An x-ray spectroscopy study

Science.gov (United States)

Chen, Kai; Sundermann, Martin; Strigari, Fabio; Kawabata, Jo; Takabatake, Toshiro; Tanaka, Arata; Bencok, Peter; Choueikani, Fadi; Severing, Andrea

2018-04-01

Here we present linear and circular polarized soft x-ray absorption spectroscopy (XAS) data at the Ce M4 ,5 edges of the electron (Ir) and hole-doped (Re) Kondo semiconductor CeOs2Al10 . Both substitutions have a strong impact on the unusual high Néel temperature TN=28.5 K, and also the direction of the ordered moment in case of Ir. The substitution dependence of the linear dichroism is weak thus validating the crystal-field description of CeOs2Al10 being representative for the Re and Ir substituted compounds. The impact of electron and hole doping on the hybridization between conduction and 4 f electrons is related to the amount of f0 in the ground state and reduction of x-ray magnetic circular dichroism. A relationship of c f -hybridization strength and enhanced TN is discussed. The direction and doping dependence of the circular dichroism strongly supports the idea of strong Kondo screening along the crystallographic a direction.

Photodynamic Processes in Fluoride Crystals Doped with Ce3+

Directory of Open Access Journals (Sweden)

Pavlov V.V.

2015-01-01

Full Text Available Integrated studies of photoelectric phenomena and their associated photodynamic processes in LiCaAlF6, LiLuF4, LiYF4, LiY0,5Lu0,5F4, SrAlF5 crystals doped with Ce3+ ions have been carried out using the combination of the methods of optical and dielectric spectroscopy. The numerical values of the basic parameters of photodynamic processes and their spectral dependence in 240 – 310 nm spectral range are evaluated. It has been shown that the most probable process, which leads to the photoionization of Ce3+ ions in LiYxLu1-xF4:Ce3+ (x=0; 0,5; 1 and LiCaAlF6:Ce3+ crystals, is excited-state absorption to the states of mixed configurations of Ce3+ ions localized near/in the conduction band of crystal.

Experimental evaluation of Gd3Al2Ga3O12:Ce (GAGG:Ce) single crystals coupled to a silicon photomultiplier (SiPM) under high gamma ray irradiation conditions

Science.gov (United States)

Metallinos, A.; Kefalidis, E.; Kandarakis, I.; David, S.

2017-11-01

Cerium (Ce) ion doped scintillators are of high interest in Medical Imaging systems and radiation monitoring devices, due to their very fast response and very good emission characteristics. In this study, a series of measurements regarding the energy resolution, photofraction, sensitivity, as well as the figure of merit, of Gd3Al2Ga3O12:Ce (GAGG:Ce) scintillator crystals, is presented. All GAGG:Ce crystals have a surface area of 3x3 mm2 with varying thicknesses, from 4 up to 20 mm (4, 5, 6, 8, 10, 15 and 20 mm). These crystals were exposed to γ radiation, using two different radioactive sources: 137Cs (0.662 MeV) and 60Co (1.173 MeV and 1.332 MeV). Each crystal was measured individually and was optically coupled to a KETEK PM3350 SiPM, an optical sensor with high gain, suitable to operate in room temperature. The digitization of the pulses was accomplished using CAEN DT5720 desktop digitizer and its corresponding digital pulse processing (DPP) firmware. Each measurement was performed in a light-tight box and had duration of 30 min. The best energy resolution value was measured for the GAGG:Ce crystal with dimensions 3x3x15mm3, equal to 3.9% at 1.332 MeV. Results were evaluated and compared to previous published data.

Luminescence properties of Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F (M=Ca, Ba, 0{<=}x{<=}0.9, 0.001{<=}y{<=}0.05) phosphors

Energy Technology Data Exchange (ETDEWEB)

Choi, Hye-Min [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of); Park, Sangmoon, E-mail: spark@silla.ac.kr [Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736 (Korea, Republic of)

2012-09-15

Luminescent materials composed of Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F (M=Ca, Ba, 0{<=}x{<=}0.9, 0.001{<=}y{<=}0.05) were prepared by the solid-state reaction method. X-ray diffraction (XRD) patterns of the obtained oxyfluorides are exhibited for indexing peak positions. Dynamic excitation and emission spectra of the Ce{sup 3+}-activated oxyfluoride phosphors are clearly monitored. The critical emission quenching as a function of Ce{sup 3+} contents in Sr{sub 2.5-3y/2}M{sub 0.5}Ce{sub y}AlO{sub 4}F phosphors is revealed at quite low concentrations of the activator. CIE coordinates of blue and green Sr{sub 2.5-3y/2}M{sub 0.5}Ce{sub y}AlO{sub 4}F phosphors are clearly measured. The relative quantum efficiency of Sr{sub 2.4985}Ca{sub 0.5}Ce{sub 0.005}AlO{sub 4}F based on the integrated emission is determined. The Sr{sub 3-x-3y/2}M{sub x}Ce{sub y}AlO{sub 4}F phosphors excited near 410 nm light could be prominent phosphors in applications of NUV-LED. - Highlights: Black-Right-Pointing-Pointer Blue and green emitting oxyfluoride phosphors are excitated near 410 nm Black-Right-Pointing-Pointer Ce{sup 3+}-activated oxyfluoride phosphors are quite effective to prepare white light for near-UV LED applications. Black-Right-Pointing-Pointer Gradual substitution of Ce{sup 3+} content in the oxyfluoride hosts changes CIE values.

Microstructure and Mechanical Strengths of Metastable FCC Solid Solutions in Al-Ce-Fe System

OpenAIRE

A., Inoue; H., Yamaguchi; M., Kikuchi; T., Masumoto; Institute for Materials Research; Institute for Materials Research; Institute for Materials Research; Institute for Materials Research

1990-01-01

A metastable fcc solid solution (SS) with high mechanical strengths and good bending ductility was found to be formed in rapidly solidified Al-Ce-Fe alloys containing the solute elements below about 6 at%. The SS consists of equiaxed grains with a size of about 2μm and contains a high density of internal defects. The highest hardness (H_v) and tensile fracture strengtn (σ_f) are 440 and 860 MPa in the as-quenched state and remain almost unchanged up to about 600 K for 1 h, though fine compoun...

Structure and scintillation yield of Ce-doped Al–Ga substituted yttrium garnet

International Nuclear Information System (INIS)

Sidletskiy, Oleg; Kononets, Valerii; Lebbou, Kheirreddine; Neicheva, Svetlana; Voloshina, Olesya; Bondar, Valerii; Baumer, Vyacheslav; Belikov, Konstantin; Gektin, Alexander; Grinyov, Boris; Joubert, Marie-France

2012-01-01

Highlights: ► Range of Y 3 (Al 1−x Ga x ) 5 O 12 :Ce solid solution crystals are grown from melt by the Czochralski method. ► Light yield of mixed crystals reaches 130% of the YAG:Ce value at x ∼ 0.4. ► ∼1% of antisite defects is formed in YGG:Ce, but no evidence of this is obtained for the rest of crystals. -- Abstract: Structure and scintillation yield of Y 3 (Al 1−x Ga x ) 5 O 12 :Ce solid solution crystals are studied. Crystals are grown from melt by the Czochralski method. Distribution of host cations in crystal lattice is determined. Quantity of antisite defects in crystals is evaluated using XRD and atomic emission spectroscopy data. Trend of light output at Al/Ga substitution in Y 3 (Al 1−x Ga x ) 5 O 12 :Ce is determined for the first time. Light output in mixed crystals reaches 130% comparative to Ce-doped yttrium–aluminum garnet. Luminescence properties at Al/Ga substitution are evaluated.

Towards the development of new phosphors with reduced content of rare earth elements: Structural and optical characterization of Ce:Tb: Al{sub 2}SiO{sub 5}

Energy Technology Data Exchange (ETDEWEB)

Chiriu, D.; Stagi, L.; Carbonaro, C.M.; Corpino, R. [Dipartimento di Fisica, Università degli Studi di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy); Casula, M.F. [Dipartimento di Scienze Chimiche e Geologiche and INSTM, Università di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy); Ricci, P.C., E-mail: carlo.ricci@dsf.unica.it [Dipartimento di Fisica, Università degli Studi di Cagliari, S.P.n°8 Km 0, 700, I-09042 Monserrato (Italy)

2016-05-15

Highlights: • A new promising inert matrix as host of luminescent ions is proposed. • Al2SiO5 matrix is free from Rare earths (critical raw materials). • Doping the matrix with Ce and Tb we obtain an efficient green emitter. • Cerium acts as sensitizer for Terbium emission. - Abstract: A new promising inert matrix as host of luminescent ions is proposed. Al2SiO5 samples, doped with rare earths (Ce, Tb single doped and co-doped) are proposed as good prospect for the development of new UV–vis converter with reduced content of rare earths elements. Structural characterization by Raman, XRD spectroscopy and TEM imaging reveals the sillimanite phase and nano sized dimension of the investigated powders. Optical characterization by steady time and time resolved emission spectroscopy for the single doped and co-doped samples allows to identify an efficient energy transfer from Ce to Tb ions under near UV excitation wavelength. The intense green emission observed in the Ce:Tb co-doped Al2SiO5 system suggests its potential application as efficient blue pumped green emitter phosphor to be exploited for white LED: to this purpose we tested the compound in combination with a red emitting doping ion recording for Ce:Tb:Cr:ASO system a correlated color temperature of 6720 K.

Synthesis and characterization of Ce doped MFI zeolite

International Nuclear Information System (INIS)

Kalita, Banani; Talukdar, Anup K.

2012-01-01

Highlights: ► Cerium was incorporated into the tetrahedral position of MFI zeolite structure. ► Unit cell volume increases with an increase of Ce content in the framework of MFI. ► A band at 310 nm in the UV–vis spectra indicates Ce incorporation in MFI structure. ► The mass loss (%) in the region 373–423 K decreases with increase of Ce in MFI. - Abstract: Ce doped MFI (mobil five) zeolites with different Si to (Ce + Al) and different Ce to Al ratios were synthesized by a hydrothermal synthesis method. All the samples were characterized by different techniques such as X-ray diffraction, Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), UV–vis diffuse reflectance spectroscopy (DRS) and scanning electron microscopy (SEM). The results showed that almost pure MFI phase was obtained in all cases with incorporation of cerium metal into the framework. The increase in unit cell parameters observed with an increase in Ce content is indicative of incorporation of Ce into the framework structure of microporous material MFI. Corroboration of the framework incorporation of Ce into the MFI zeolite structure was also obtained from the UV–vis DRS spectra by the presence of an absorption band at 280 nm. TGA and SEM of the samples provide complementary evidence for Ce incorporation into the framework MFI structure.

Luminescence properties of Ce{sup 3+} and Tb{sup 3+} co-activated ZnAl{sub 2}O{sub 4} phosphor

Energy Technology Data Exchange (ETDEWEB)

Tshabalala, K.G. [Department of Physics, University of the Free State, Bloemfontein, ZA 9300 (South Africa); Cho, S.-H.; Park, J.-K. [Nano-Materials Center, Korea Institute of Science and Technology, Cheongryang, Seoul 130-650 (Korea, Republic of); Pitale, Shreyas S.; Nagpure, I.M.; Kroon, R.E.; Swart, H.C. [Department of Physics, University of the Free State, Bloemfontein, ZA 9300 (South Africa); Ntwaeaborwa, O.M., E-mail: ntwaeab@ufs.ac.za [Department of Physics, University of the Free State, Bloemfontein, ZA 9300 (South Africa)

2012-05-15

In this study, a solution combustion method was used to prepare green emitting Ce{sup 3+}-Tb{sup 3+} co-activated ZnAl{sub 2}O{sub 4} phosphor. The samples were annealed at 700 Degree-Sign C in air or hydrogen atmosphere to improve their crystallinity and optical properties. X-ray diffraction study confirmed that both as-prepared and post-preparation annealed samples crystallized in the well known cubic spinel structure of ZnAl{sub 2}O{sub 4}. An agglomeration of irregular platelet-like particles whose surfaces were encrusted with smaller spheroidal particles was confirmed by scanning electron microscopy (SEM). The fluorescence data collected from the annealed samples with different concentrations of Ce{sup 3+} and Tb{sup 3+} show the enhanced green emission at 543 nm associated with {sup 5}D{sub 4}{yields}{sup 7}F{sub 5} transitions of Tb{sup 3+}. The enhancement was attributed to energy transfer from Ce{sup 3+} to Tb{sup 3+}. Possible mechanism of energy transfer via a down conversion process is discussed. Furthermore, cathodoluminescence (CL) intensity degradation of this phosphor was also investigated and the degradation data suggest that the material was chemically stable and the CL intensity was also stable after 10 h of irradiation by a beam of high energy electrons.

Ni/CeO{sub 2}-Al{sub 2}O{sub 3} catalysts promoted with noble metals for the hydrogen production by ethanol vapor reforming; Catalisadores de Ni/CeO{sub 2}-Al{sub 2}O{sub 3} promovidos com metais nobres para a producao de hidrogenio por reforma a vapor de etanol

Energy Technology Data Exchange (ETDEWEB)

Profeti, Luciene P.R.; Ticianelli, Edson Antonio; Assaf, Elisabete Moreira [Universidade de Sao Paulo (IQSC/USP), Sao Carlos, SP (Brazil). Inst. de Quimica]. E-mail: eassaf@iqsc.usp.br

2008-07-01

The catalytic activity of Ni/CeO{sub 2}-Al{sub 2}O{sub 3} catalysts modified with noble metals (Ru, Ir, Pt and Pd) was investigated in the steam reforming of ethanol. The catalysts were characterized by energy dispersive spectroscopy, X-ray diffraction, UV-Vis diffuse reflectance spectroscopy and H{sub 2} temperature-programmed reduction-X-ray absorption fine structure (XANES). The results showed that the formation of inactive nickel aluminate was avoided due to the presence of a CeO{sub 2} dispersed on the alumina. The promoting effect of noble metals included a decrease of the reduction temperatures of NiO species interacting with the support due to the hydrogen spillover effect, leading to an increase of the reducibilities of the promoted catalysts The better catalytic performance for the ethanol steam reforming was obtained for the NiPd/CeAl catalyst, which presented an effluent gaseous mixture with the highest H{sub 2} yield. (author)

Improvement of photoluminescence properties and thermal stability of Y2.9Ce0.1Al5−xSixO12 phosphors with Si3N4 addition

International Nuclear Information System (INIS)

Zhang, Fangfang; Song, Kaixin; Jiang, Jun; Wu, Song; Zheng, Peng; Huang, Qingming; Xu, Junming; Qin, Huibin

2014-01-01

Highlights: • Y 2.9 Ce 0.1 Al 5−x Si x O 12 phosphors were prepared by solid-state reaction in reduced air ambience. • Si 4+ could be incorporated into the host lattice of Y 3 Al 5 O 12 through partial occupation of the Al 3+ sites. • Si 3 N 4 addition can improve photoluminescence efficiency and thermal stability of Y 3 Al 5 O 12 :Ce. - Abstract: A series of Si 3 N 4 doping Y 2.9 Ce 0.1 Al 5−x Si x O 12−3x/2 N 4x/3 phosphors were prepared by solid-state reaction in 95%N 2 –5%H 2 reduced air ambience. The XRD characteristics plus Rietveld refinement results shows that the as-sintered powders are unique crystal phase with the same crystal structure of Y 3 Al 5 O 12 (PDF No. 79-1891). The N element was not detected by the analysis of X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectrum (EDS). The photoluminescence spectra (PL and PLE) tests show that the exciting and emitting intensity of PLE and PL gradually increase due to the increase of Si 3 N 4 concentration. Meanwhile, the phosphorescence decay times are prolonged from 45 ns (x = 0) to 78 ns (x = 0.3), under the monitor of 530 nm wavelength. The thermoluminescence tests (TL) confirm the thermal stability of as-phosphors with Si 3 N 4 addition is much better than that of the pristine Y 2.9 Ce 0.1 Al 5 O 12 phosphors

Characteristics and corrosion studies of vanadate conversion coating formed on Mg-14 wt%Li-1 wt%Al-0.1 wt%Ce alloy

Energy Technology Data Exchange (ETDEWEB)

Ma Yibin [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Li Ning, E-mail: lininghit@263.net [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Li Deyu [School of Chemical Engineering and Technology, Harbin Institute of Technology, Harbin 150001 (China); Zhang Milin; Huang Xiaomei [Key Laboratory of Superlight Materials and Surface Technology, Ministry of Education, Harbin Engineering University, Harbin 150001 (China)

2012-11-15

Highlights: Black-Right-Pointing-Pointer Vanadate film forms on the surface of Mg-Li-Al-Ce alloy. Black-Right-Pointing-Pointer Vanadate coating improves the corrosion resistance. Black-Right-Pointing-Pointer Vanadate coating is composed of Mg(OH){sub 2}, Li{sub 2}O and V{sub 2}O{sub 5}. - Abstract: Mg-14Li-1Al-0.1Ce alloy is immersed in NH{sub 4}VO{sub 3} + K{sub 3}(Fe(CN){sub 6}) solutions with different NH{sub 4}VO{sub 3} and/or K{sub 3}(Fe(CN){sub 6}) concentrations, and different immersion time. The surface morphology and composition of the vanadate coating are then characterized by scanning electron microscopy with energy dispersion spectroscopy (SEM-EDS) and X-ray photoelectron spectroscopy (XPS), and the corrosion behavior of the conversion coating is studied by polarization technique and electrochemical impedance spectroscopy (EIS). The experimental results indicate that the vanadate film with better corrosion resistance forms on Mg-Li-Al-Ce surface after the sample is immersed in 30 g L{sup -1} NH{sub 4}VO{sub 3} + 3.75 g L{sup -1} K{sub 3}(Fe(CN){sub 6}) solution at 80 Degree-Sign C for 10 min. The coating consists of V{sub 2}O{sub 5}, Li{sub 2}O and Mg(OH){sub 2}.

Estudo microestrutural do catalisador Ni/gama-Al2O3: efeito da adição de CeO2 na reforma do metano com dióxido de carbono Microstructural study of Ni/gamma-Al2O3 catalyst: addition effects of CeO2 on carbon dioxide reforming of methane

Directory of Open Access Journals (Sweden)

Antoninho Valentini

2003-10-01

Full Text Available The carbon dioxide reforming of methane was carried out over nickel catalysts supported on the gamma-Al2O3/CeO2 system prepared by wet impregnation. With the increase of the CeO2 weight in the catalyst, a higher stability was observed in the catalytic activity, together with an excellent resistance to carbon deposition and a better Ni dispersion. The catalysts were characterized by means of surface area measurements, TPR, H2 chemisorption, XRD, SEM, EDX, XPS and TEM. An interaction between Ni and CeO2 was observed to the Ni/CeO2 sample after activation in a H2 atmosphere above 300 ºC. Such behavior has a significantly influence on the catalytic activity.

Magnetic properties of CE(Fe sub(1-x) Al sub(x))2 for x<=0.20

International Nuclear Information System (INIS)

Franceschini, D.F.; Cunha, S.F. da.

1985-01-01

Magnetization measurements of the system Ce(Fe sub(1-x) Al sub(x)) 2 for x 2 has not a simple dilution effect. Together with a accentuated decrease in the iron mean magnetic moment and in Curie temperatures was observed, above a certain concentration, a transition from ferromagnetism to a canted spin phase upon decreasing temperature. For the higher concentration range the system exhibits magnetic freezing effects. A preliminary magnetic phase diagram was proposed. (Author) [pt

Synthesis and luminescent study of Ce3+-doped terbium–yttrium aluminum garnet

International Nuclear Information System (INIS)

Dotsenko, V.P.; Berezovskaya, I.V.; Zubar, E.V.; Efryushina, N.P.; Poletaev, N.I.; Doroshenko, Yu.A.; Stryganyuk, G.B.; Voloshinovskii, A.S.

2013-01-01

Highlights: ► Ce 3+ -doped garnets (TYAG) were prepared using nanostructured reagents. ► The Ce 3+ ions cause a very efficient yellow emission of the samples. ► The reasons for the long wavelength position of this emission are discussed. ► Contribution from Al atoms to the conduction band of TYAG is quite essential. - Abstract: Terbium–yttrium aluminum garnets (TYAG) doped with Ce 3+ ions have been prepared by solid state reactions between nanostructured oxides of aluminum and rare earths. The luminescent properties of Ce 3+ ions in (Tb 0.8 Y 0.2 ) 3(1−x) Ce 3x Al 5 O 12 (x = 0.03) have been studied upon excitation in the 2–20 eV region. The substitution of Tb 3+ for Y 3+ in the garnet structure results in broadening the emission band and shifting its maximum towards the longer wavelengths. It was found that in addition to the 4f n → 4f n−1 5d excitation bands of Ce 3+ and Tb 3+ ions, the excitation spectra for the Ce 3+ emission contain broad bands at 6.73 and ∼9.5 eV. These bands are attributed to the Ce 3+ -bound exciton formation and O 2p → Al 3s, 3p transitions, respectively. In contrast to the predictions based on the results of electronic structure calculations on Y 3 Al 5 O 12 and Tb 4 Al 2 O 9 , the threshold of interband transitions in TYAG is at high energies (⩾7.3 eV), and contributions from Al tetr and Al oct atoms to the conduction-band density of states are evaluated as quite essential.

Partial oxidation of methane to syngas on Rh/Al{sub 2}O{sub 3} and Rh/Ce-ZrO{sub 2} catalysts

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Raquel L.; Bitencourt, Isabela G.; Passos, Fabio B., E-mail: fbpassos@vm.uff.br [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Dept. de Engenharia Quimica e Petroleo

2013-01-15

The partial oxidation of methane with {gamma}-Al{sub 2}O{sub 3}-, CeO{sub 2}-, ZrO{sub 2}- and Ce-ZrO{sub 2}-supported rhodium catalysts was investigated. DRIFTS (diffuse reflectance infrared spectroscopy) measurements of adsorbed CO showed the formation of different rhodium species on different supports, which influenced the dispersion of the metal. The effects of the metal dispersion, oxygen storage capacity on the activity of these catalysts for the partial oxidation of methane are discussed. (author)

Hybrid Density Functional Study of the Local Structures and Energy Levels of CaAl2O4:Ce3.

Science.gov (United States)

Lou, Bibo; Jing, Weiguo; Lou, Liren; Zhang, Yongfan; Yin, Min; Duan, Chang-Kui

2018-05-03

First-principles calculations were carried out for the electronic structures of Ce 3+ in calcium aluminate phosphors, CaAl 2 O 4 , and their effects on luminescence properties. Hybrid density functional approaches were used to overcome the well-known underestimation of band gaps of conventional density functional approaches and to calculate the energy levels of Ce 3+ ions more accurately. The obtained 4f-5d excitation and emission energies show good consistency with measured values. A detailed energy diagram of all three sites is obtained, which explains qualitatively all of the luminescent phenomena. With the results of energy levels calculated by combining the hybrid functional of Heyd, Scuseria, and Ernzerhof (HSE06) and the constraint occupancy approach, we are able to construct a configurational coordinate diagram to analyze the processes of capture of a hole or an electron and luminescence. This approach can be applied for systematic high-throughput calculations in predicting Ce 3+ activated luminescent materials with a moderate computing requirement.

Investigation on the Structure and Electrochemical Properties of La-Ce-Mg-Al-Ni Hydrogen Storage Alloy

Directory of Open Access Journals (Sweden)

Yuqing Qiao

2013-01-01

Full Text Available Structure and electrochemical characteristics of La0.96Ce0.04Mg0.15Al0.05Ni2.8 hydrogen storage alloy have been investigated. X-ray diffraction analyses reveal that the La0.96Ce0.04Mg0.15Al0.05Ni2.8 hydrogen storage alloy consisted of a (La, MgNi3 phase with the rhombohedral PuNi3-type structure and a LaNi5 phase with the hexagonal CaCu5-type structure. TEM shows that the alloy is multicrystal with a lattice space 0.187 nm. EDS analyse shows that the content of Mg is 3.48% (atom which coincide well with the designed composition of the electrode alloy. Electrochemical investigations show that the maximum discharge capacity of the alloy electrode is 325 mAh g−1. The alloy electrode has higher discharge capacity within the discharge current density span from 60 mA g−1 to 300 mA g−1. Electrochemical impedance spectroscopy measurements indicate that the charge transfer resistance RT on the alloy electrode surface and the calculated exchange current density I0 are 0.135 Ω and 1298 mA g−1, respectively; the better eletrochemical reaction kinetic of the alloy electrode may be responsible for the better high-rate dischargeability.

Platinum triangles in the Pt/Al framework of the intermetallic REPt6Al3 (RE = Ce-Nd, Sm, Gd, Tb) series

International Nuclear Information System (INIS)

Eustermann, Fabian; Stegemann, Frank; Renner, Konstantin; Janka, Oliver

2017-01-01

The compounds of the REPt 6 Al 3 series (RE = Ce-Nd, Sm, Gd, Tb) were obtained by reaction of the elements via arc-melting. They were characterized by powder and single-crystal X-ray diffraction (NdPt 6 Al 3 : wR = 0.0432, 759 F 2 values, 33 variables) as well as by magnetic susceptibility measurements. The isostructural compounds crystallize with a new structure type in the trigonal crystal system with space group R anti 3c, twelve formula units in the unit cell, and lattice parameters of a = 752-755 and c = 3882-3945 pm. The crystal structure can be described by different slabs stacked along [001]. One layer features Pt 3 triangles, centering the cavities of a flat honeycomb RE layer that are arranged in a..ABCA ' B ' C ' .. sequence. The other layer consists of condensed hexagonal [Pt 6 Al 6 ] prisms, centered by Pt atoms, separating the before mentioned slabs. Magnetic measurements revealed that all rare-earth atoms are in the trivalent oxidation state, however, due to the low lanthanoide content magnetic ordering phenomena were observed only at low temperatures [SmPt 6 Al 3 : T C = 5.0(1) K; GdPt 6 Al 3 : T C = 7.3(1) K; TbPt 6 Al 3 : T N = 3.6(1) K]. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

In situ neutron diffraction study of the plastic deformation mechanisms of B2 ordered intermetallic alloys: NiAl, CuZn, and CeAg

Energy Technology Data Exchange (ETDEWEB)

Wollmershauser, J.A. [Department of Materials Science and Engineering, University of Virginia, P.O. Box 400745, 116 Engineer' s Way, Charlottesville, VA 22904-04745 (United States); Kabra, S. [Materials Science and Technology Division, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Agnew, S.R. [Department of Materials Science and Engineering, University of Virginia, P.O. Box 400745, 116 Engineer' s Way, Charlottesville, VA 22904-04745 (United States)], E-mail: sra4p@virginia.edu

2009-01-15

The internal stress developments of B2 compounds NiAl, CuZn, and CeAg are examined using in situ neutron diffraction. CeAg is a representative of a newly discovered class of fully ordered and ductile B2 compounds. Using polycrystal plasticity modeling to interpret the results, it is revealed that the internal stress evolution of CeAg is nearly identical to that of NiAl, indicating that they share a common primary mechanism of plastic deformation, i.e., <1 0 0>{l_brace}0 1 1{r_brace} 'cube' slip. This result reinforces the dilemma previously observed for rare-earth alloys CuY, AgY, and CuDy, since cube slip provides insufficient independent slip systems to accommodate large-scale homogenous polycrystalline deformation. There is no evidence in the diffraction data of either mechanical twinning or stress-induced phase transformation. The activity of bcc-type <1 1 1>{l_brace}11-bar0{r_brace} slip at high stresses is confirmed and a lower bound for the critical resolved shear stress is quantified.

Microstructures and Properties of Laser Cladding Al-TiC-CeO₂ Composite Coatings.

Science.gov (United States)

He, Xing; Kong, Dejun; Song, Renguo

2018-01-26

Al-TiC-CeO₂ composite coatings have been prepared by using a laser cladding technique, and the microstructure and properties of the resulting composite coatings have been investigated using scanning electron microscopy (SEM), a 3D microscope system, X-ray diffraction (XRD), micro-hardness testing, X-ray stress measurements, friction and wear testing, and an electrochemical workstation. The results showed that an Al-Fe phase appears in the coatings under different applied laser powers and shows good metallurgical bonding with the matrix. The dilution rate of the coating first decreases and then increases with increasing laser power. The coating was transformed from massive and short rod-like structures into a fine granular structure, and the effect of fine grain strengthening is significant. The microhardness of the coatings first decreases and then increases with increasing laser power, and the maximum microhardness can reach 964.3 HV 0.2 . In addition, the residual stress of the coating surface was tensile stress, and crack size increases with increasing stress. When the laser power was 1.6 kW, the coating showed high corrosion resistance.

Microstructural study of Ni/γ-Al2O3 catalyst: addition effects of CeO2 on carbon dioxide reforming of methane

International Nuclear Information System (INIS)

Valentini, Antoninho; Probst, Luiz Fernando Dias; Carreno, Neftali L. V.; Leite, Edson R.; Pontes, Fenelon M.; Longo, Elson; Schreiner, Wido H.; Lisboa-Filho, Paulo N.

2003-01-01

The carbon dioxide reforming of methane was carried out over nickel catalysts supported on the γ-Al 2 O 3 /CeO 2 system prepared by wet impregnation. With the increase of the Co2 weight in the catalyst, a higher stability was observed in the catalytic activity, together with an excellent resistance to carbon deposition and a better Ni dispersion. The catalysts were characterized by means of surface area measurements, TPR, H 2 chemisorption, XRD, SEM, EDX, XPS and TEM. An interaction between Ni and CeO 2 was observed to the Ni/CeO 2 sample after activation in a H 2 atmosphere above 300 deg C. Such behavior has a significantly influence on the catalytic activity. (author)

Preparation and inhibition properties of molybdate intercalated ZnAlCe layered double hydroxide

Energy Technology Data Exchange (ETDEWEB)

Yan, Huajie; Wang, Jihui, E-mail: jhwang@tju.edu.cn; Zhang, Yu; Hu, Wenbin

2016-09-05

ZnAlCe layered double hydroxide intercalated by molybdate (ZnAlCe−MoO{sub 4} LDH) was successfully synthesized by using co-precipitation method, and the morphology, structure of ZnAlCe−MoO{sub 4} LDH were observed and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) techniques. The inhibition behavior of ZnAlCe−MoO{sub 4} LDH for Q235 steel in 3.5%NaCl solution was determined by polarization curves, electrochemical impedance spectroscopy (EIS), inductively coupled plasma mass spectrometer (ICP-MS) and X-ray photoelectron spectrometer (XPS) methods. The results shows that the synthesized ZnAlCe−MoO{sub 4} LDH has a lamellar structure with a particle size of 0.1–2.0 μm, an average thickness of 30 nm, and a basal plane spacing of 0.898 nm. Compared with the addition of ZnAl layered double hydroxide intercalated by nitrate (ZnAl−NO{sub 3} LDH) and ZnAl layered double hydroxide intercalated by molybdate (ZnAl−MoO{sub 4} LDH) in 3.5% NaCl solution, Q235 steel in 3.5%NaCl + ZnAlCe−MoO{sub 4} LDH solution has a lower corrosion current density, larger polarization resistance and a higher inhibition efficiency. The addition of ZnAlCe−MoO{sub 4} LDH will reduce the chloride concentration in 3.5% NaCl solution by the anion exchanged with molybdate, and improve the corrosion resistance of Q235 steel owing to the formation of passive film with the composition of ferrous or iron molybdate and deposition film with zinc and cerium hydroxides. - Highlights: • ZnAlCe−MoO{sub 4} LDH compound was successfully synthesized by co-precipitation method. • ZnAlCe−MoO{sub 4} LDH has a better inhibition effect to Q235 steel in 3.5%NaCl solution. • The Cl{sup −} ions in solution was partially exchanged with MoO{sub 4}{sup 2−} ions in host layers. • The passive film and deposition film were formed by the release of LDH compound.

Nuclear magnetic resonance investigation of the heavy fermion system Ce2CoAl7Ge4

Science.gov (United States)

Dioguardi, A. P.; Guzman, P.; Rosa, P. F. S.; Ghimire, N. J.; Eley, S.; Brown, S. E.; Thompson, J. D.; Bauer, E. D.; Ronning, F.

2017-12-01

We present nuclear magnetic resonance (NMR) and nuclear quadrupole resonance (NQR) measurements performed on single crystalline Ce2CoAl7Ge4 , a member of a recently discovered family of heavy fermion materials Ce2M Al7Ge4 (M =Co , Ir, Ni, or Pd). Previous measurements indicated a strong Kondo interaction as well as magnetic order below TM=1.8 K . Our NMR spectral measurements show that the Knight shift K is proportional to the bulk magnetic susceptibility χ at high temperatures. A clear Knight shift anomaly (K ¬∝χ ) is observed at coherence temperatures T*˜17.5 K for H0∥c ̂ and 10 K for H0∥a ̂ at the 59Co site, and T*˜12.5 K at the 27Al(3) site for H0∥a ̂ characteristic of the heavy fermion nature of this compound. At high temperatures, the 59Co NMR spin-lattice relaxation rate T1-1 is dominated by spin fluctuations of the 4 f local moments with a weak metallic background. The spin fluctuations probed by 59Co NMR are anisotropic and larger in the basal plane than in the c direction. Furthermore, we find (T1T K ) -1∝T-1 /2 at the 59Co site as expected for a Kondo system for T >T* and T >TK . 59Co NQR T1-1 measurements at low temperatures indicate slowing down of spin fluctuations above the magnetic ordering temperature TM˜1.8 K . A weak ferromagnetic character of fluctuations around q =0 is evidenced by an increase of χ T versus T above the magnetic ordering temperature. We also find good agreement between the observed and calculated electric field gradients at all observed sites.

Frictional properties of CeO$_{2}$-Al$_{2}$O$_{3}$-ZrO$_{2}$ plasma-sprayed film under mixed and boundary lubricating conditions

CERN Document Server

Kita, H; Osumi, K; 10.2109/jcersj.112.615

2004-01-01

In order to find a counterpart for reducing the frictional coefficient of Al/sub 2/O/sub 3/-ZrO/sub 2/-CeO/sub 2/ plasma-sprayed film, the sliding properties in mixed and boundary lubricating conditions was investigated. It was found that combination of a CrN- coated cast iron pin and an Al/sub 2/O/sub 3/-ZrO/sub 2/-CeO/sub 2/ plasma sprayed plate provided the lowest frictional coefficient among several combinations chosen from practical materials. The coefficient of friction was much lower than that of the materials combination widely used for piston ring and cylinder liner. It was inferred that the combination of a pin made of hard materials with high density, a smooth surface such as CrN-coated cast iron and a porous plate can reduce the frictional coefficient because less sliding resistance is implemented and porosity retains oil.

Effect of nano-CeO 2 on microstructure properties of TiC/TiN+TiCN ...

Indian Academy of Sciences (India)

TiC/TiN+TiCN-reinforced composite coatings were fabricated on Ti–6Al–4V alloy by laser cladding, which improved surface performance of the substrate. ... X-ray diffraction results indicated that Al3Ti+TiC/TiN+nano-CeO2 laser-cladded coating consisted of Ti3Al, TiC, TiN, Ti2Al20Ce, TiC0.3N0.7, Ce(CN)3 and CeO2, this ...

Microstructure and mechanical properties of Mg–Al-based alloy modified with cerium

International Nuclear Information System (INIS)

Chaubey, A.K.; Scudino, S.; Prashanth, K.G.; Eckert, J.

2015-01-01

Mg 90 Al 10–x Ce x with x=0, 1, 3 and 5 (at%) have been prepared by copper mold casting and the influence of Ce on the microstructure and mechanical properties have been investigated. The addition of 1% Ce decreases the volume fraction of the γ-Mg 17 Al 12 phase and with the further increase of Ce to 3% and 5%, the γ-Mg 17 Al 12 intermetallic disappears completely with the formation of the Al 11 Ce 3 and Al 2 Ce intermetallic phases. The room temperature compression tests show that Ce addition significantly improves the room temperature mechanical properties. For example, the alloy with 5% Ce displays a strength of 448 MPa compared to 318 MPa of the binary Ce-free alloy along with appreciable plasticity of about 9%. This improvement is due to grain refinement as well as to the precipitation of the Al 11 Ce 3 and Al 2 Ce strengthening phases

Lu{sub 3}(Al,Si){sub 5}(O,N){sub 12}:Ce{sup 3+} phosphors with broad emission band and high thermal stability for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Liu, Jiaqing; Wang, Xiaojun; Xuan, Tongtong; Wang, Chunbo; Li, Huili, E-mail: hlli@phy.ecnu.edu.cn; Sun, Zhuo

2015-02-15

A yellow-orange emitting Lu{sub 3}Al{sub 5−x}Si{sub x}O{sub 12−x}N{sub x}:Ce{sup 3+} phosphor with excellent color rendering, high luminescent efficiency and high thermal stability was reported in this paper. It was synthesized by a conventional solid-state reaction method. The effect of Si{sup 4+}–N{sup 3−} incorporation on the optical properties of Lu{sub 3}Al{sub 5}O{sub 12}:Ce{sup 3+} phosphor was investigated and compared to YAG:Ce{sup 3+} with the same compositions. Similarly, the addition of α-Si{sub 3}N{sub 4} leads to a distinct redshift and broadening of photoluminescent spectrum, which is assigned to the increased covalency and crystal field strength caused by N{sup 3−}. Nevertheless, an excellent thermal stability and a higher integrated intensity presented by α-Si{sub 3}N{sub 4}-doped LuAG:Ce{sup 3+} are distinctive. Further, the emission intensity can be greatly enhanced by adding NaF flux. Finally, the white LED flat lamp with a CRI as high as 83 and a luminous efficiency of 85 lm/W is successfully realized by using a single LuAG-based oxynitride phosphor combined with a blue LED chip, which is completely feasible for general indoor illuminations to replace the traditional fluorescent or incandescent lamps. - Highlights: • Si{sub 3}N{sub 4}-doped LuAG:Ce{sup 3+} oxynitride phosphors were synthesized by a solid-state reaction. • The effect of Si{sup 4+}–N{sup 3−} incorporation on the optical properties was investigated. • The addition of Si{sub 3}N{sub 4} leads to an obvious redshift of the emission spectra. • Lu{sub 3}Al{sub 5−x}Si{sub x}O{sub 12−x}N{sub x}:Ce{sup 3+} shows an excellent thermal stability and a higher intensity. • A warm white LED with CRI=83 is achieved by a single oxynitride phosphor.

Luminescence and Energy Transfer in Lu3Al5O12 Scintillators Co-Doped with Ce3+ and Tb3+

NARCIS (Netherlands)

Ogiegło, J.M.; Zych, A.K.; Ivanovskikh, K.; Jüstel, T.; Ronda, R.C.; Meijerink, A.

2012-01-01

Lu3Al5O12 (LuAG) doped with Ce3+ is a promising scintillator material with a high density and a fast response time. The light output under X-ray or γ-ray excitation is, however, well below the theoretical limit. In this paper the influence of codoping with Tb3+ is investigated with the aim to

Synthesis by sol-gel and characterization of catalysts Ag/Al2O3- CeO2 for the elimination of nitric oxide

International Nuclear Information System (INIS)

Zayas R, M.L.

2005-01-01

The environmental pollution is one from the big problems to solve at the present time, because the quality of the alive beings life is affected. For such reason, more clean and economic technologies are required, that it conduces to develop new catalytic alternatives to diminish the nitrogen oxides that due to its chemical processes in the environment contribute considerably in the air pollution. The main objective of the present work, is the preparation and characterization of catalytic materials with base of silver supported in simple and mixed aluminium oxides (Al 2 O 3 ) and Cerium oxide (CeO 2 ), and its catalytic evaluation that through of the reduction of nitric oxide (NO) using hydrogen (H 2 ) as reducer agent. It was synthesized alumina (Al 2 O 3 ) and Cerium oxide (CeO 2 ) and mixed oxides (Al 2 O 3 - CeO 2 ), by the sol-gel method and the cerium oxide (CeO 2 ) by precipitation of the cerium nitrate (III) hexa hydrated. The oxides were stabilized thermally at 900 C by 5 hr. The catalysts were prepared by impregnation using silver nitrate (AgNO 3 ), the nominal concentration of Ag was of 5% in weight. The catalysts were reduced at 400 C by 2 hr, in hydrogen flow of 60 cc/min. The characterization of the catalytic materials was carried out through different techniques as: nitrogen adsorption to determine the surface area BET, scanning electron microscopy (SEM) to observe the final morphology of the catalysts, X-ray diffraction (XRD) to identify the crystalline phases of the catalytic materials, Infrared spectroscopy (DRIFT) to know the structural characterization of the catalysts, reduction to programmed temperature (TPR) to evidence the interaction metal-support. The catalytic properties of the catalysts were evaluated in the model reaction NO + H 2 , to determine the activity and selectivity. The results indicate that the preparation technique, the precursors and the thermal treatments that underwent these materials influence in the catalyst and by

Reinvestigation of the Ce–Co–Al ternary system: Isothermal section at 973 K

Energy Technology Data Exchange (ETDEWEB)

Nasri, N. [Unité de Recherche de Chimie des Matériaux et de l’Environnement, ISSBAT, Université de Tunis El Manar, 9 av. Dr. Zoheir Safi, 1006 Tunis (Tunisia); Gastebois, J. [Institut des Sciences Chimiques de Rennes, Chimie du Solide et Matériaux, UMR CNRS 6226, Université Rennes 1, Campus de Beaulieu, 263 av. Général Leclerc, 35042 Rennes Cedex (France); Pasturel, M., E-mail: mathieu.pasturel@univ-rennes1.fr [Institut des Sciences Chimiques de Rennes, Chimie du Solide et Matériaux, UMR CNRS 6226, Université Rennes 1, Campus de Beaulieu, 263 av. Général Leclerc, 35042 Rennes Cedex (France); Belgacem, B. [Unité de Recherche de Chimie des Matériaux et de l’Environnement, ISSBAT, Université de Tunis El Manar, 9 av. Dr. Zoheir Safi, 1006 Tunis (Tunisia); Péron, I.; Gouttefangeas, F. [Centre de Microscopie Electronique à Balayage et microAnalyse, Université Rennes 1, Campus de Beaulieu, 263 av. Général Leclerc, 35042 Rennes Cedex (France); Ben Hassen, R. [Unité de Recherche de Chimie des Matériaux et de l’Environnement, ISSBAT, Université de Tunis El Manar, 9 av. Dr. Zoheir Safi, 1006 Tunis (Tunisia); and others

2015-04-15

Highlights: • The experimental isothermal section at 973 K of the Ce–Co–Al system is presented. • This section contains 5 ternary phases and 7 ternary extensions of pseudo-binaries. • DTA experiments are used to estimate the liquid areas. - Abstract: The Ce–Co–Al ternary phase diagram has been reinvestigated at 973 K by means of powder X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and differential thermal analyses. It contains 5 ternary phases (CeCo{sub 2}Al{sub 8}, Ce{sub 2}Co{sub 6}Al{sub 19}, CeCoAl{sub 4}, Ce{sub 3}Co{sub 3}Al{sub 4} and CeCoAl) as well as 7 extensions in the ternary field of pseudo-binaries (CeAl{sub 2−x}Co{sub x} with 0 ⩽ x ⩽ 0.18; CeCo{sub 2−x}Al{sub x} with 0 ⩽ x ⩽ 0.21; CeCo{sub 3−y}Al{sub y} with 0 ⩽ y ⩽ 0.20; Ce{sub 2}Co{sub 7−x}Al{sub x} with 0 ⩽ x ⩽ 0.73; Ce{sub 5}Co{sub 19−y}Al{sub y} with 0 ⩽ y ⩽ 0.20; CeCo{sub 5−x}Al{sub x} with 0 ⩽ x ⩽ 0.71 and Ce{sub 2}Co{sub 17−y}Al{sub y} with 0 ⩽ y ⩽ 2.2). Two liquid areas are present at the Al and Ce-rich corners of this isothermal section.

Study of magnetic properties of TGa6 with T = Ce, Pr, Nd, Tb, Ho, Dy and of solid solutions Ce(Ga1-x Alx)2

International Nuclear Information System (INIS)

Jerjini, M.

1987-10-01

At low temperature TGa 6 compounds are ordered with a Neel temperature of about 10 K. Magnetic structures are antiferromagnetic for T = Pr or Nd or modulated for T = Tb, Ho or Dy. Ce presents an abnormal behavior in CeGa 6 . Neutron inelastic scattering allows the determination of energy levels in the crystal field of cerium ion and evidences hybridation of 4f and valence electrons. Three magnetic transitions for T 6 . Study of CeGa 6 and solid solutions. Ce(Ga (1-x) Al x ) 2 shows that aluminium insertion reinforces the Kondo effect. For x = O.1 an incommensurable structure subsists at very low temperature. CeGa 2 is ordered with 3 magnetic structures. Magnetic moment is reduced with Al. The study of crystal field by neutron scattering shows that hybridation effects are more important for the compound with x = 0.1 [fr

Microstructure and mechanical properties of Mg–Al-based alloy modified with cerium

Energy Technology Data Exchange (ETDEWEB)

Chaubey, A.K., E-mail: anil.immt@gmail.com [Institute of Minerals and Materials Technology (IMMT), Bhubaneswar 751013 (India); Scudino, S.; Prashanth, K.G. [IFW Dresden, Institut für Komplexe Materialien, Postfach 270116, D-01171 Dresden (Germany); Eckert, J. [IFW Dresden, Institut für Komplexe Materialien, Postfach 270116, D-01171 Dresden (Germany); TU Dresden, Institut für Werkstoffwissenschaft, D-01062 Dresden (Germany)

2015-02-11

Mg{sub 90}Al{sub 10–x}Ce{sub x} with x=0, 1, 3 and 5 (at%) have been prepared by copper mold casting and the influence of Ce on the microstructure and mechanical properties have been investigated. The addition of 1% Ce decreases the volume fraction of the γ-Mg{sub 17}Al{sub 12} phase and with the further increase of Ce to 3% and 5%, the γ-Mg{sub 17}Al{sub 12} intermetallic disappears completely with the formation of the Al{sub 11}Ce{sub 3} and Al{sub 2}Ce intermetallic phases. The room temperature compression tests show that Ce addition significantly improves the room temperature mechanical properties. For example, the alloy with 5% Ce displays a strength of 448 MPa compared to 318 MPa of the binary Ce-free alloy along with appreciable plasticity of about 9%. This improvement is due to grain refinement as well as to the precipitation of the Al{sub 11}Ce{sub 3} and Al{sub 2}Ce strengthening phases.

Nanocrystallization in Al85Ce8Ni5Co2 amorphous alloy obtained by different strain rate during high pressure torsion

International Nuclear Information System (INIS)

Henits, P.; Kovacs, Zs.; Schafler, E.; Varga, L.K.; Labar, J.L.; Revesz, A.

2010-01-01

In order to elucidate the role of total strain and strain rate during high pressure torsion of Al 85 Ce 8 Ni 5 Co 2 metallic glass, different deformation conditions were applied to devitrify the as-quenched alloy. The disk-shaped specimens were characterized by X-ray diffraction, transmission electron microscopy and thermal analysis.

Development and characterization of nickel catalysts supported in CeO{sub 2}-ZrO{sub 2}-Al{sub 2}O{sub 3}, CeO{sub 2}-La{sub 2}O{sub 3}-Al{sub 2}O{sub 3} e ZrO{sub 2}-La{sub 2}O{sub 3}-Al{sub 2}O{sub 3} matrixes evaluated for methane reforming reactions; Desenvolvimento e caracterização de catalisadores de níquel suportados em matrizes CeO{sub 2}-ZrO{sub 2}-Al{sub 2}O{sub 3}, CeO{sub 2}-La{sub 2}O{sub 3}-Al{sub 2}O{sub 3} e ZrO{sub 2}-La{sub 2}O{sub 3}-Al{sub 2}O{sub 3} avaliados para as reações de reforma do metano

Energy Technology Data Exchange (ETDEWEB)

Abreu, Amanda Jordão de

2012-07-01

Nowadays, the methane reforming is large interest industrial for the take advantage of these gas in production the hydrogen and synthesis gas (syngas). Among in the reactions of methane stand of the reactions steam reforming and carbon dioxide reforming of methane. The main catalysts uses in the methane reforming is Ni/Al{sub 2}O{sub 3}. However, the supported-nickel catalyst is susceptible to the deactivation or the destruction by coke deposition. The carbon dissolves in the nickel crystallite and its diffuses through the nickel, leading for formation of the carbon whiskers, which results in fragmentation of the catalyst. Modification of such catalysts, like incorporation of suitable promoters, is desirable to achieve reduction of the methane hydrogenolysis and/or promotion of the carbon gasification. Catalysts 5%Ni/Al{sub 2}O{sub 3} supported on solid solutions formed by ZrO{sub 2}-CeO{sub 2}, La{sub 2}O{sub 3} and CeO{sub 2}-ZrO{sub 2}-La{sub 2}O{sub 3} were prepared, characterized and evaluated in reactions steam and carbon dioxide reforming and partial oxidation of methane with objective the value effect loading solution solid in support. The supports were prepared by co-precipitation method and catalysts were prepared by impregnation method and calcined at 500 deg C. The supports and catalysts were characterized by Nitrogen Adsorption, method -rays diffraction (XRD), X-rays dispersive spectroscopy (XDS), spectroscopy in the region of the ultraviolet and the visible (UV-vis NIR) to and temperature programmed reduction (TPR), Raman Spectroscopy, X-ray absorption spectroscopy and Thermogravimetric Analysis. After all the catalytic reactions check which the addition of solid solution is beneficial for Ni/Al{sub 2}O{sub 3} catalysts and the best catalysts are Ni/CeO{sub 2}-La{sub 2}O{sub 3}-Al{sub 2}O{sub 3}. (author)

Fractal dimension and energetic heterogeneity of gold-modified Al-Fe-Ce pilc's

International Nuclear Information System (INIS)

Carriazo, J.G.; Molina, R.; Moreno, S.

2008-01-01

This paper studies the energetic and topographical changes that occur on the surface of a series of clays pillared with the mixed Al-Fe-Ce system and on the surface of solids synthesized by the deposition of gold nanoparticles over these pillared clays. The energetic heterogeneity of the solids was analyzed by means of the distribution of the adsorption potential, while the variations in the fractal dimension were determined from the nitrogen adsorption isotherms at 77 K, using the equation proposed by Avnir-Jaroniec. Results show the generation of microporous structures with important topographical modifications indicating an increase in the roughness (fractal geometry) of the surface of the solids as a consequence of the pillaring, revealing a positive effect of cerium addition in the synthesis process and the possible formation of nanoparticles of iron species and gold on the surface of pillared clays. The solids were also analyzed by transmission electron microscopy (TEM), confirming the formation of nanoparticles on the surface.

Crystal growth and scintillation properties of multi-component oxide single crystals: Ce:GGAG and Ce:La-GPS

Energy Technology Data Exchange (ETDEWEB)

Yoshikawa, A., E-mail: yoshikawa@imr.tohoku.ac.jp [Institute for Materials Research (IMR), Tohoku University, Sendai 980-8577 (Japan); New Industry Creation Hatchery Center (NICHe), Tohoku University, Sendai 980-8579 (Japan); C& A Corporation, 6-6-40 Aramaki Aza Aoba, Aoba-ku, Sendai 980-8579 (Japan); Kamada, K. [New Industry Creation Hatchery Center (NICHe), Tohoku University, Sendai 980-8579 (Japan); C& A Corporation, 6-6-40 Aramaki Aza Aoba, Aoba-ku, Sendai 980-8579 (Japan); Kurosawa, S. [Institute for Materials Research (IMR), Tohoku University, Sendai 980-8577 (Japan); New Industry Creation Hatchery Center (NICHe), Tohoku University, Sendai 980-8579 (Japan); Shoji, Y. [Institute for Materials Research (IMR), Tohoku University, Sendai 980-8577 (Japan); C& A Corporation, 6-6-40 Aramaki Aza Aoba, Aoba-ku, Sendai 980-8579 (Japan); Yokota, Y. [New Industry Creation Hatchery Center (NICHe), Tohoku University, Sendai 980-8579 (Japan); Chani, V.I. [Institute for Materials Research (IMR), Tohoku University, Sendai 980-8577 (Japan); Nikl, M. [Institute of Physics, AS CR, Cukrovarnická 10, 162 53 Prague (Czech Republic)

2016-01-15

Crystal growth by micro-pulling-down, Czochralski, and floating zone methods and scintillation properties of Ce:Gd{sub 3}(Ga,Al){sub 5}O{sub 12} (Ce:GGAG) multi-component oxide garnets, and Ce:Gd{sub 2}Si{sub 2}O{sub 7} (Ce:GPS) or Ce:(La,Gd){sub 2}Si{sub 2}O{sub 7} (Ce:La-GPS) pyro-silicates are reviewed. GGAG crystals demonstrated practically linear dependences of some of the parameters including lattice constant, emission wavelength, and band gap on Ga content. However, emission intensity, light yield and energy resolution showed maxima for intermediate compositions. GGAG crystals had the highest light yield of 56,000 photon/MeV for Ga content of 2.7 atoms per garnet formula unit. Similarly the light yield and energy resolution of La-GPS showed the highest values of 40,000 photon/MeV and 4.4%@662 keV, respectively, for La-GPS containing 10% of La. Moreover, La-GPS demonstrated stable scintillation performance up to 200 °C.

Effect of nano-CeO2 on microstructure properties of TiC/TiN+nTi(CN) reinforced composite coating

International Nuclear Information System (INIS)

Jianing, Li; Chuanzhong, Chen; Cuifang, Zhang

2012-01-01

TiC/TiN+TiCN reinforced composite coatings were fabricated on Ti-6Al-4V alloy by laser cladding, which improved surface performance of the substrate. Nano-CeO 2 was able to suppress crystallization and growth of the crystals in the laser-cladded coating to a certain extent. With the addition of proper content of nano-CeO 2 , this coating exhibited fine microstructure. In this study, the Al 3 Ti+TiC/TiN+nano-CeO 2 laser-cladded coatings were studied by means of X-ray diffraction and scanning electron microscope. The X-ray diffraction results indicated that the Al 3 Ti+TiC/TiN+nano-CeO 2 laser-cladded coating consisted of Ti 3 Al, TiC, TiN, Ti 2 Al 20 Ce, TiC 0.3 N 0.7 , Ce(CN) 3 and CeO 2 , this phase constituent was beneficial to increase the microhardness and wear resistance of Ti-6Al-6V alloy. (author)

Low-density to high-density transition in Ce{sub 75}Al{sub 23}Si{sub 2} metallic glass

Energy Technology Data Exchange (ETDEWEB)

Zeng, Q S; Lou, H B; Gong, Y; Wang, X D; Jiang, J Z [International Center for New-Structured Materials, Zhejiang University, Hangzhou 310027 (China); Fang, Y Z; Wu, F M [College of Mathematics, Physics and Information Engineering, Zhejiang Normal University, Jinhua 321004, Zhejiang (China); Yang, K; Li, A G; Yan, S; Yu, X H [Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201203 (China); Lathe, C, E-mail: qiaoshizeng@gmail.co, E-mail: jiangjz@zju.edu.c [HASYLAB am DESY, Notkestrasse 85, Hamburg D-22603 (Germany)

2010-09-22

Using in situ high-pressure x-ray diffraction (XRD), we observed a pressure-induced polyamorphic transition from the low-density amorphous (LDA) state to the high-density amorphous (HDA) state in Ce{sub 75}Al{sub 23}Si{sub 2} metallic glass at about 2 GPa and 300 K. The thermal stabilities of both LDA and HDA metallic glasses were further investigated using in situ high-temperature and high-pressure XRD, which revealed different pressure dependences of the onset crystallization temperature (T{sub x}) between them with a turning point at about 2 GPa. Compared with Ce{sub 75}Al{sub 25} metallic glass, minor Si doping shifts the onset polyamorphic transition pressure from 1.5 to 2 GPa and obviously stabilizes both LDA and HDA metallic glasses with higher T{sub x} and changes their slopes dT{sub x}/dP. The results obtained in this work reveal another polyamorphous metallic glass system by minor alloying (e.g. Si), which could modify the transition pressure and also properties of LDA and HDA metallic glasses. The minor alloying effect reported here is valuable for the development of more polyamorphous metallic glasses, even multicomponent bulk metallic glasses with modified properties, which will trigger more investigations in this field and improve our understanding of polyamorphism and metallic glasses.

Nano-ZnO Particles’ Effect in Improving the Mechanical Response of Mg-3Al-0.4Ce Alloy

Directory of Open Access Journals (Sweden)

Sravya Tekumalla

2016-11-01

Full Text Available Magnesium based nanocomposites, due to their excellent dimensional stability and mechanical integrity, have a lot of potential to replace the existing commercial Al alloys and steels used in aerospace and automotive applications. Mg-Al alloys are commercially used in the form of AZ (magnesium-aluminum-zinc and AM (magnesium-aluminum-manganese series in automobile components. However, the Mg17Al12 phase in Mg-Al alloys is a low melting phase which results in a poor creep and high temperature performance of the alloys. Rare earth additions modify the phase and hence improve the properties of the materials. In this paper, Ce and nano ZnO particles were added to Mg-Al alloys to attain a favorable effect on their properties. The developed materials exhibited promising properties in terms of thermal expansion coefficient (CTE, hardness, and tensile strength. Further, the ZnO addition refined the microstructure and helped in obtaining a uniform distribution, however without grain size refinement. The increased addition of ZnO and the improvement in the distribution led to an enhancement in the properties, rendering the materials suitable for a wide spectrum of engineering applications.

CEF-scheme of a semimetal Ce3Sn7

International Nuclear Information System (INIS)

Okuda, Yusuke; Yamamoto, Takeshi; Honda, Daisuke; Shishido, Hiroaki; Galatanu, Andrei; Haga, Yoshinori; Matsuda, Tatsuma D.; Takeuchi, Tetsuya; Kindo, Koichi; Sugiyama, Kiyohiro; Settai, Rikio; O-bar nuki, Yoshichika

2005-01-01

We measured the magnetic susceptibility and magnetization of an antiferromagnet Ce 3 Sn 7 with the orthorhombic crystal structure. The experimental data are found to be well explained on the basis of the crystalline electric field (CEF) 4f-scheme under the assumption that two Ce atoms in the 2(a) site possess a magnetic moment of 0.36μ B /Ce and one Ce atom in the 4(i) site possesses no magnetic moment as in a valence fluctuating compound CeSn 3 , which was previously proposed by Bonnet et al. Furthermore, we carried out the de Haas-van Alphen experiment. The detected Fermi surfaces are many in number but are extremely small in volume, indicating that Ce 3 Sn 7 is a semimetal

Influence of thermal treatment and γ-radiation on absorption, luminescence and scintillation properties of Lu3Al5O12:Ce single crystalline films

International Nuclear Information System (INIS)

Zorenko, Yu.; Pavlyk, B.; Turchak, R.; Zorenko, T.; Gorbenko, V.; Konstankevych, I.; Savchyn, V.; Voznyak, T.

2007-01-01

The influence of thermal treatment (TT) and irradiation by γ-quanta ( 60 Co, 1.25 MeV) in the range of absorbed doses 10 6 -10 8 R on the absorption, luminescence and light yield (LY) of scintillators based on Lu 3 Al 5 O 12 :Ce (LuAG:Ce) single crystalline films (SCF) grown by LPE from the Pb-based flux is studied. It has been shown that transformation of the Fe 3+ ↔Fe 2+ and Pb 2+ ↔Pb 4+ valent states of iron and lead trace impurities cause the change in the optical absorption of SCF induced by the TT in air and vacuum in the range of annealing temperatures of 800-1200 0 C. Possible types of radiation defects in LuAG:Ce SCF induced by γ-radiation are analyzed

Platinum triangles in the Pt/Al framework of the intermetallic REPt{sub 6}Al{sub 3} (RE = Ce-Nd, Sm, Gd, Tb) series

Energy Technology Data Exchange (ETDEWEB)

Eustermann, Fabian; Stegemann, Frank; Renner, Konstantin [Institut fuer Anorganische und Analytische Chemie, Westfaelische Wilhelms-Universitaet Muenster (Germany); Janka, Oliver [Institut fuer Anorganische und Analytische Chemie, Westfaelische Wilhelms-Universitaet Muenster (Germany); Institut fuer Chemie, Carl von Ossietzky Universitaet Oldenburg (Germany)

2017-12-13

The compounds of the REPt{sub 6}Al{sub 3} series (RE = Ce-Nd, Sm, Gd, Tb) were obtained by reaction of the elements via arc-melting. They were characterized by powder and single-crystal X-ray diffraction (NdPt{sub 6}Al{sub 3}: wR = 0.0432, 759 F{sup 2} values, 33 variables) as well as by magnetic susceptibility measurements. The isostructural compounds crystallize with a new structure type in the trigonal crystal system with space group R anti 3c, twelve formula units in the unit cell, and lattice parameters of a = 752-755 and c = 3882-3945 pm. The crystal structure can be described by different slabs stacked along [001]. One layer features Pt{sub 3} triangles, centering the cavities of a flat honeycomb RE layer that are arranged in a..ABCA{sup '}B{sup '}C{sup '}.. sequence. The other layer consists of condensed hexagonal [Pt{sub 6}Al{sub 6}] prisms, centered by Pt atoms, separating the before mentioned slabs. Magnetic measurements revealed that all rare-earth atoms are in the trivalent oxidation state, however, due to the low lanthanoide content magnetic ordering phenomena were observed only at low temperatures [SmPt{sub 6}Al{sub 3}: T{sub C} = 5.0(1) K; GdPt{sub 6}Al{sub 3}: T{sub C} = 7.3(1) K; TbPt{sub 6}Al{sub 3}: T{sub N} = 3.6(1) K]. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Pulse shape discrimination properties of Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce,B single crystal in comparison with CsI:Tl

Energy Technology Data Exchange (ETDEWEB)

Rawat, S. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Department of Physics, Indian Institute of Technology, Roorkee 247667 (India); Tyagi, Mohit [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Netrakanti, P.K.; Kashyap, V.K.S.; Mitra, A. [Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Singh, A.K.; Desai, D.G. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India); Kumar, G. Anil [Department of Physics, Indian Institute of Technology, Roorkee 247667 (India); Gadkari, S.C. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai 400085 (India)

2016-12-21

Single crystals of Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce,B and CsI:Tl were grown by Czochralski and Bridgman techniques, respectively. While both the crystals exhibited similar emission at about 550 nm, their scintillation decay times showed significantly different characteristics. The average scintillation decay time of Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce,B crystal was found to be about 284 ns for alpha excitation compared to 108 ns measured for a gamma source. On the other hand in CsI:Tl crystals, the alpha excitation resulted in a lower average decay time of 600 ns compared to 1200 ns with gamma excitation. Their pulse shape discrimination (PSD) for gamma and alpha radiations were studied by coupling the scintillators with photomultiplier tube or SiPM and employing an advanced digitizer as well as a conventional zero-crossing setup. In spite of having a poor α/γ light yield ratio, the PSD figure of merit and the difference of zero-crossing time in Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce,B crystals were found to be superior in comparison to CsI:Tl crystals.

Microstructures and Properties of Laser Cladding Al-TiC-CeO2 Composite Coatings

Science.gov (United States)

Kong, Dejun; Song, Renguo

2018-01-01

Al-TiC-CeO2 composite coatings have been prepared by using a laser cladding technique, and the microstructure and properties of the resulting composite coatings have been investigated using scanning electron microscopy (SEM), a 3D microscope system, X-ray diffraction (XRD), micro-hardness testing, X-ray stress measurements, friction and wear testing, and an electrochemical workstation. The results showed that an Al-Fe phase appears in the coatings under different applied laser powers and shows good metallurgical bonding with the matrix. The dilution rate of the coating first decreases and then increases with increasing laser power. The coating was transformed from massive and short rod-like structures into a fine granular structure, and the effect of fine grain strengthening is significant. The microhardness of the coatings first decreases and then increases with increasing laser power, and the maximum microhardness can reach 964.3 HV0.2. In addition, the residual stress of the coating surface was tensile stress, and crack size increases with increasing stress. When the laser power was 1.6 kW, the coating showed high corrosion resistance. PMID:29373555

Constraining Mantle Differentiation Processes with La-Ce and Sm-Nd Isotope Systematics

Science.gov (United States)

Willig, M.; Stracke, A.

2016-12-01

Cerium (Ce) and Neodymium (Nd) isotopic ratios in oceanic basalts reflect the time integrated La-Ce and Sm-Nd ratios, and hence the extent of light rare earth element element (LREE) depletion or enrichment of their mantle sources. New high precision Ce-Nd isotope data from several ocean islands define a tight array in ԑCe-ԑNd space with ԑNd = -8.2±0.4 ԑCe + 1.3±0.9 (S.D.), in good agreement with previous data [1, 2]. The slope of the ԑCe-ԑNd array and the overall isotopic range are sensitive indicators of the processes that govern the evolution of the mantle's LREE composition. A Monte Carlo approach is employed to simulate continuous mantle-crust differentiation by partial melting and recycling of crustal materials. Partial melting of mantle peridotites produces variably depleted mantle and oceanic crust, which evolve for different time periods, before the oceanic crust is recycled back into the mantle including small amounts of continental crust (GLOSS [3]). Subsequently, depleted mantle and recycled materials of variable age and composition melt, and the respective melts mix in different proportions. Mixing lines strongly curve towards depleted mantle, and tend to be offset from the data for increasingly older and more depleted mantle. Observed ԑCe-ԑNd in ridge [1] and ocean island basalts and the slope of the ԑCe-ԑNd array therefore define upper limits for the extent and age of LREE depletion preserved in mantle peridotites. Very old average mantle depletion ages (> ca. 1-2 Ga) for the bulk of the mantle are difficult to reconcile with the existing ԑCe-ԑNd data, consistent with the range of Nd-Hf-Os model ages in abyssal peridotites [4-6]. Moreover, unless small amounts of continental crust are included in the recycled material, it is difficult to reproduce the relatively shallow slope of the ԑCe-ԑNd array, consistent with constraints from the ԑNd - ԑHf mantle array [7]. [1] Makishima and Masuda, 1994 Chem. Geol. 118, 1-8. [2] Doucelance et al

Co-doping effects on luminescence and scintillation properties of Ce doped Lu3Al5O12 scintillator

International Nuclear Information System (INIS)

Kamada, Kei; Nikl, Martin; Kurosawa, Shunsuke; Beitlerova, Alena; Nagura, Aya; Shoji, Yasuhiro; Pejchal, Jan; Ohashi, Yuji; Yokota, Yuui; Yoshikawa, Akira

2015-01-01

The Mg, Ca, Sr and Ba 200 ppm co-doped Ce:Lu 3 Al 5 O 12 single crystals were prepared by micro pulling down method. Absorption and luminescence spectra were measured together with several other scintillation characteristics, namely the scintillation decay and light yield to reveal the effect of the co-doping. The scintillation decays were accelerated by both Mg and Ca co-dopants. The Mg co-doped samples showed the fastest decay and the highest light yield among the co-doped samples

Effect of Ce addition on the mechanical and electrochemical properties of a lithium battery shell alloy

International Nuclear Information System (INIS)

Zhang, Junchao; Ding, Dongyan; Xu, Xinglong; Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua; Huang, Yuanwei; Tang, Jinsong

2014-01-01

Highlights: • Fabrication of Ce-free and Ce-containing Al–Cu–Mn–Fe–Mg alloy. • TEM, tensile and electrochemical characterization of the alloys. • Ce element greatly affects the precipitation of the alloy. • Ce element had great impact on the tensile strength and corrosion potential of the alloys. - Abstract: Due to severe application environment lithium battery shell of new-energy automotives requires increasing demands for using high performance aluminum alloys. In the present work, effect of Ce addition on the microstructure, tensile and electrochemical properties of an Al–Cu–Mn–Mg–Fe alloy were investigated through using X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), tensile tests and electrochemical tests. The experimental results indicated that the addition of Ce element could promote the precipitation of second phases. With addition of 0.36% Ce, high melting point Al 8 Cu 4 Ce phase and many Al 20 Cu 2 Mn 3 particles could be found. In addition, the precipitation of conventionally dominant phase of Al 2 Cu could be suppressed in alloy. The Ce addition was found to result in enhanced tensile strength and improved corrosion resistance

Effect of Ce addition on the mechanical and electrochemical properties of a lithium battery shell alloy

Energy Technology Data Exchange (ETDEWEB)

Zhang, Junchao [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Ding, Dongyan, E-mail: dyding@sjtu.edu.cn [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Xu, Xinglong [School of Materials Science and Engineering, Shanghai Jiao Tong University, Shanghai 200240 (China); Gao, Yongjin; Chen, Guozhen; Chen, Weigao; You, Xiaohua [Huafon NLM Al Co., Ltd, Shanghai 201506 (China); Huang, Yuanwei; Tang, Jinsong [Shanghai Huafon Materials Technology Institute, Shanghai 201203 (China)

2014-12-25

Highlights: • Fabrication of Ce-free and Ce-containing Al–Cu–Mn–Fe–Mg alloy. • TEM, tensile and electrochemical characterization of the alloys. • Ce element greatly affects the precipitation of the alloy. • Ce element had great impact on the tensile strength and corrosion potential of the alloys. - Abstract: Due to severe application environment lithium battery shell of new-energy automotives requires increasing demands for using high performance aluminum alloys. In the present work, effect of Ce addition on the microstructure, tensile and electrochemical properties of an Al–Cu–Mn–Mg–Fe alloy were investigated through using X-ray diffraction (XRD), transmission electron microscopy (TEM), scanning electron microscopy (SEM), tensile tests and electrochemical tests. The experimental results indicated that the addition of Ce element could promote the precipitation of second phases. With addition of 0.36% Ce, high melting point Al{sub 8}Cu{sub 4}Ce phase and many Al{sub 20}Cu{sub 2}Mn{sub 3} particles could be found. In addition, the precipitation of conventionally dominant phase of Al{sub 2}Cu could be suppressed in alloy. The Ce addition was found to result in enhanced tensile strength and improved corrosion resistance.

Synthesis of CeS and interactions with molten metals

International Nuclear Information System (INIS)

Krikorian, O.H.; Curtis, P.G.

1988-01-01

Hot-pressed and sintered discs of single-phase CeS were tested for interaction with molten aluminium, uranium, and iron to determine the conditions under which reaction first begins and the nature of the reaction. Aluminium begins to react with CeS at ∼ 1190 K, slowly dissolving cerium and forming a thin layer of Ce 3 S 4 at the reaction interface. At 1363 K, aluminium wets and spreads over the CeS surface and dissolves ∼ 01 at% Ce. Ce 3 Al 11 precipitates out in the aluminium phase on cooldown. Uranium does not react with CeS at 1673 K, but at 1873 K it wets and spreads on CeS and dissolves ∼ 100 atom ppm S, which precipitates out as US on cooldown. Iron wets CeS at 1873 K and 1973 K but does not spread or interact. Because of the desirable containment characteristics of CeS and similar sulfides for molten metals, we recommend their use in a number of applications. (author)

Effect of CeO₂ on Microstructure and Wear Resistance of TiC Bioinert Coatings on Ti6Al4V Alloy by Laser Cladding.

Science.gov (United States)

Chen, Tao; Liu, Defu; Wu, Fan; Wang, Haojun

2017-12-31

To solve the lack of wear resistance of titanium alloys for use in biological applications, various prepared coatings on titanium alloys are often used as wear-resistant materials. In this paper, TiC bioinert coatings were fabricated on Ti6Al4V by laser cladding using mixed TiC and ZrO₂ powders as the basic pre-placed materials. A certain amount of CeO₂ powder was also added to the pre-placed powders to further improve the properties of the TiC coatings. The effects of CeO₂ additive on the phase constituents, microstructures and wear resistance of the TiC coatings were researched in detail. Although the effect of CeO₂ on the phase constituents of the coatings was slight, it had a significant effect on the microstructure and wear resistance of the coatings. The crystalline grains in the TiC coatings, observed by a scanning electron microscope (SEM), were refined due to the effect of the CeO₂. With the increase of CeO₂ additive content in the pre-placed powders, finer and more compact dendrites led to improvement of the micro-hardness and wear resistance of the TiC coatings. Also, 5 wt % content of CeO₂ additive in the pre-placed powders was the best choice for improving the wear properties of the TiC coatings.

Cerium intermetallics CeTX. Review III

Energy Technology Data Exchange (ETDEWEB)

Poettgen, Rainer; Janka, Oliver [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Chevalier, Bernard [Bordeaux Univ., Pessac (France). Inst. de Chimie de la Matiere Condensee de Bordeaux

2016-05-01

The structure-property relationships of CeTX intermetallics with structures other than the ZrNiAl and TiNiSi type are systematically reviewed. These CeTX phases form with electron-poor and electron-rich transition metals (T) and X = Mg, Zn, Cd, Hg, Al, Ga, In, Tl, Si, Ge, Sn, Pb, P, As, Sb, and Bi. The review focusses on the crystal chemistry, the chemical bonding peculiarities, and the magnetic and transport properties. Furthermore {sup 119}Sn Moessbauer spectroscopic data, high-pressure studies, hydrogenation reactions and the formation of solid solutions are reviewed. This paper is the third of a series of four reviews on equiatomic intermetallic cerium compound [Part I: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 289; Part II: R. Poettgen, B. Chevalier, Z. Naturforsch. 2015, 70b, 695].

Timing characteristics of Ce doped Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12} single crystals in comparison with CsI(Tl) scintillators

Energy Technology Data Exchange (ETDEWEB)

Tyagi, M.; Singh, A.K.; Singh, S.G.; Sen, S.; Gadkari, S.C. [Technical Physics Division, Bhabha Atomic Research Centre, Mumbai, 400085 (India); Desai, V.V.; Nayak, B.K. [Nuclear Physics Division, Bhabha Atomic Research Centre, Mumbai, 400085 (India)

2015-10-15

Single crystals of Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce with B codopants were successfully grown using the Czochralski technique. The timing characteristics of the crystal was measured by coupling the crystal to photomultiplier tubes (PMT) or silicon photodiodes [Si(PIN)]. The two prompt γ-rays emitted in a cascade from {sup 60}Co or {sup 22}Na source were detected in coincidence using Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12}:Ce,B crystal detectors and a BaF{sub 2} detector. The time resolution of these crystals are observed to be better than that measured for CsI:Tl crystal coupled to PMT or Si(PIN) in an identical measurement setup. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Multielement (P-Yb-Zr-Ce-Al-Ca) fiber for moderate-power laser application with enhanced photodarkening resistivity

Energy Technology Data Exchange (ETDEWEB)

Dhar, Anirban; Paul, Mukul Chandra [CSIR-Central Glass and Ceramic Research Institute, 196 Raja S. C. Mullick Road, Jadavpur, Kolkata 700 032 (India); Das, Shyamal; Reddy, Pinninty Harshavardhan; Siddiki, Salim H.; Dutta, Debjit; Pal, Mrinmay [Academy of Scientific and Innovative Research (AcSIR), CSIR-CGCRI Campus, Kolkata 700 032 (India); Kir' yanov, Alexander V. [Centro de Investigaciones en Optica, Loma del Bosque 115, Col. Lomas del Campestre, Leon 37150, Guanajuato (Mexico)

2017-06-15

Multielement (ME) (P-Yb-Zr-Ce-Al-Ca) nanophase separated silica-glass-based optical fiber is fabricated through a conventional-modified chemical vapor deposition (MCVD) process, coupled with solution doping technique. The lasing and photodarkening behaviors of this ME fiber have been demonstrated and compared, in terms of its photodarkening (PD) performance at moderate pump powers (tens of Watts), with standard Yb-doped fiber with phospho-alumino-silicate (PAS) glass composition, which clearly reveals that the ME-Yb doped fiber is a promising candidate for laser applications with enhanced PD resistivity. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Optical spectroscopy of the Ce-doped multicomponent garnets

International Nuclear Information System (INIS)

Canimoglu, A.; Karabulut, Y.; Ayvacikli, M.; Muresan, L.E.; Perhaita, I.; Barbu-Tudoran, L.; Garcia Guinea, J.; Karali, T.; Can, N.

2016-01-01

Here, we report our results referring to the preparation of Ce doped Y 2.22 MgGa 2 Al 2 SiO 12 , Y 1.93 MgAl 4 SiO 12 and Y 2.22 Gd 0.75 Ga 2 Al 3 O 12 using solid state reaction at high temperature. Several complementary methods (i.e. powder x-ray diffraction (XRPD), energy dispersive analysis of X-rays (EDX), scanning electron microscopy (SEM) and Fourier transforms infrared spectroscopy (FTIR)) were studied to examine the effects of the synthesis procedure on the morphology and structure. XRD analyses revealed that all compounds include yttrium aluminate phase with garnet structure. Cathodoluminescence (CL), radioluminescence (RL) and photoluminescence (PL) measurements were carried out for clarification of relationship between host lattice defects and the spectral luminescence emissions. Luminescence emission of phosphors is peaked at 530 nm assigned to 5d-4f transitions of the dopant Ce 3+ ions with a broad emission band in 400–700 nm range. Under electron irradiation, the emission spectrum of Ce doped (YGd) 3 Ga 2 Al 3 O 12 is well defined and has a characteristic fairly narrow and sharp emission band peaking at 312 nm and 624 nm corresponding to transition of 6 P 7/2 → 8 S 7/2 and 6 G J → 6 P J (Gd 3+ ), respectively. We suggest some of phosphors might be excellent phototherapy phosphor materials under electron excitation. - Highlights: • Ce-doped Multicomponent Garnets were prepared solid state reaction method. • The shape and size of phosphor particles were examined. • The narrow band UV B emission due to Gd 3+ ions were observed.

Luminescence and scintillation properties of YAG:Ce single crystal and optical ceramics

CERN Document Server

Mihóková, E; Mareš, J A; Beitlerová, A; Vedda, A; Nejezchleb, K; Blažek, K; D’Ambrosio, C

2007-01-01

We use various techniques to study optical and scintillation properties of Ce-doped yttrium aluminum garnet, Y3Al5O12 (YAG:Ce), in the form of a high-quality industrial single crystal. This was compared to optical ceramics prepared from YAG:Ce nanopowders. We present experimental data in the areas of optical absorption, radioluminescence, scintillation decay, photoelectron yield, thermally stimulated luminescence and radiation-induced absorption. The results point to an interesting feature—the absence of antisite (YAl, i.e. Y at the Al site) defects in optical ceramics. The scintillation decay of the ceramics is faster than that of the single crystal, but its photoelectron yield (measured with 1 μs integration time) is about 30–40% lower. Apart from the photoelectron yield value the YAG:Ce optical ceramic is fully comparable to a high quality industrial YAG:Ce single crystal and can become a competitive scintillator material.

Synthesis by sol-gel and characterization of catalysts Ag/Al{sub 2}O{sub 3}- CeO{sub 2} for the elimination of nitric oxide; Sintesis por sol-gel y caracterizacion de catalizadores Ag/Al{sub 2}O{sub 3}- CeO{sub 2} para la eliminacion del oxido nitrico

Energy Technology Data Exchange (ETDEWEB)

Zayas R, M.L

2005-07-01

The environmental pollution is one from the big problems to solve at the present time, because the quality of the alive beings life is affected. For such reason, more clean and economic technologies are required, that it conduces to develop new catalytic alternatives to diminish the nitrogen oxides that due to its chemical processes in the environment contribute considerably in the air pollution. The main objective of the present work, is the preparation and characterization of catalytic materials with base of silver supported in simple and mixed aluminium oxides (Al{sub 2}O{sub 3}) and Cerium oxide (CeO{sub 2}), and its catalytic evaluation that through of the reduction of nitric oxide (NO) using hydrogen (H{sub 2}) as reducer agent. It was synthesized alumina (Al{sub 2}O{sub 3}) and Cerium oxide (CeO{sub 2}) and mixed oxides (Al{sub 2}O{sub 3}- CeO{sub 2}), by the sol-gel method and the cerium oxide (CeO{sub 2}) by precipitation of the cerium nitrate (III) hexa hydrated. The oxides were stabilized thermally at 900 C by 5 hr. The catalysts were prepared by impregnation using silver nitrate (AgNO{sub 3}), the nominal concentration of Ag was of 5% in weight. The catalysts were reduced at 400 C by 2 hr, in hydrogen flow of 60 cc/min. The characterization of the catalytic materials was carried out through different techniques as: nitrogen adsorption to determine the surface area BET, scanning electron microscopy (SEM) to observe the final morphology of the catalysts, X-ray diffraction (XRD) to identify the crystalline phases of the catalytic materials, Infrared spectroscopy (DRIFT) to know the structural characterization of the catalysts, reduction to programmed temperature (TPR) to evidence the interaction metal-support. The catalytic properties of the catalysts were evaluated in the model reaction NO + H{sub 2}, to determine the activity and selectivity. The results indicate that the preparation technique, the precursors and the thermal treatments that underwent

Photocatalytic activity of Ce-modified SBA-15 for the degradation of ...

Indian Academy of Sciences (India)

transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy (XPS) and N2 adsorption/desorption analysis. ... water.7,8,18 Existence of different sites of cerium ions and ... hydrocarbons.21 In this study, Ce-SBA-15 and Ce-Al-SBA-.

Effect of CeO2 on Microstructure and Wear Resistance of TiC Bioinert Coatings on Ti6Al4V Alloy by Laser Cladding

Science.gov (United States)

Wang, Haojun

2017-01-01

To solve the lack of wear resistance of titanium alloys for use in biological applications, various prepared coatings on titanium alloys are often used as wear-resistant materials. In this paper, TiC bioinert coatings were fabricated on Ti6Al4V by laser cladding using mixed TiC and ZrO2 powders as the basic pre-placed materials. A certain amount of CeO2 powder was also added to the pre-placed powders to further improve the properties of the TiC coatings. The effects of CeO2 additive on the phase constituents, microstructures and wear resistance of the TiC coatings were researched in detail. Although the effect of CeO2 on the phase constituents of the coatings was slight, it had a significant effect on the microstructure and wear resistance of the coatings. The crystalline grains in the TiC coatings, observed by a scanning electron microscope (SEM), were refined due to the effect of the CeO2. With the increase of CeO2 additive content in the pre-placed powders, finer and more compact dendrites led to improvement of the micro-hardness and wear resistance of the TiC coatings. Also, 5 wt % content of CeO2 additive in the pre-placed powders was the best choice for improving the wear properties of the TiC coatings. PMID:29301218

Integrated chemical process for exothermic wave synthesis of high luminance YAG:Ce phosphors

International Nuclear Information System (INIS)

Won, C.W.; Nersisyan, H.H.; Won, H.I.; Youn, J.W.

2011-01-01

In this paper, high-luminance yellow-emitting Y 3 Al 5 O 12 :Ce 3+ phosphor (YAG:Ce) microparticles were prepared in a solid flame using a 1.425Y 2 O 3 +2.5Al 2 O 3 +0.15CeO 2 +k(KClO 3 +urea)+mNH 4 F precursor mixture (here k is the number of moles of the KClO 3 +urea red-ox mixture, and m is the number of moles of NH 4 F). The self-sustaining combustion process for the entire reaction sample was provided by the heat generated from the KClO 3 +urea mixture. Parametric studies demonstrated that the maximum temperature in the combustion wave varied from 885 to 1200 deg. C for k=2.0-3.0 mole and m=0-1.5 mole. X-ray analysis results showed that the product obtained in the solid flame consisted of Y 3 Al 5 O 12 :Ce 3+ and KCl phases. Therefore, after dissolving potassium chloride in distillated water, pure-phase YAG:Ce phosphor powder was obtained. The as-prepared YAG:Ce phosphor particles had diameters of 10-25 μm and good dispersity and exhibited luminescence properties comparable to those of YAG:Ce phosphor powders prepared by conventional high-temperature processing. - Highlights: → A new solid-flame strategy was developed for synthesizing high-luminance YAG:Ce phosphor. → Adding KClO 3 +CO(NH 2 ) 2 +NH 4 F mixture to oxide powders provides a low-temperature combustion process. → YAG:Ce phosphor particles 10-25 μm in diameter were obtained at 1000-1100 deg. C within tens of seconds. → As-prepared YAG:Ce emission intensity was 90.1-103.2% compared to that of the reference sample.

Effect of CeO2 on Microstructure and Wear Resistance of TiC Bioinert Coatings on Ti6Al4V Alloy by Laser Cladding

OpenAIRE

Chen, Tao; Liu, Defu; Wu, Fan; Wang, Haojun

2017-01-01

To solve the lack of wear resistance of titanium alloys for use in biological applications, various prepared coatings on titanium alloys are often used as wear-resistant materials. In this paper, TiC bioinert coatings were fabricated on Ti6Al4V by laser cladding using mixed TiC and ZrO2 powders as the basic pre-placed materials. A certain amount of CeO2 powder was also added to the pre-placed powders to further improve the properties of the TiC coatings. The effects of CeO2 additive on the ph...

Thermally stable green Ba(3)Y(PO(4))3:Ce(3+),Tb(3+) and red Ca(3)Y(AlO)(3)(BO(3))4:Eu(3+) phosphors for white-light fluorescent lamps.

Science.gov (United States)

Huang, Chien-Hao; Kuo, Te-Wen; Chen, Teng-Ming

2011-01-03

A class of thermal stable of green-emitting phosphors Ba(3)Y(PO(4))(3):Ce(3+),Tb(3+) (BYP:Ce(3+),Tb(3+)) and red-emitting phosphors Ca(3)Y(AlO)(3)(BO(3))(4):Eu(3+) (CYAB:Eu(3+)) for white-light fluorescent lamps were synthesized by high temperature solid-state reaction. We observed a decay of only 3% at 150 °C for BYP:0.25Ce3+,0.25Tb3+ (3% for LaPO4:Ce(3+),Tb(3+)), and a decay of 4% for CYAB:0.5Eu(3+) (7% for Y(2)O(3):Eu(3+), 24% for Y(2)O(2)S:Eu(3+)). The emission intensity of composition-optimized Ba(3)(Y(0.5)Ce(0.25)Tb(0.25))(PO(4))(3) is 70% of that of commercial LaPO(4):Ce(3+),Tb(3+) phosphors, and the CIE chromaticity coordinates are found to be (0.323, 0.534). The emission intensity of Ca(3)(Y(0.5)Eu(0.5))(AlO)(3)(BO(3))(4) is 70% and 83% of those of Y(2)O(3):Eu(3+) and Y(2)O(2)S:Eu(3+) phosphors, respectively, and the CIE chromaticity coordinates are redder (0.652, 0.342) than those of Y(2)O(3):Eu(3+) (0.645, 0.347) and Y(2)O(2)S:Eu(3+) (0.647, 0.343). A white-light fluorescent lamp is fabricated using composition-optimized Ba(3)(Y(0.5)Ce(0.25)Tb(0.25))(PO(4))(3) and Ca(3)(Y(0.5)Eu(0.5))(AlO)(3)(BO(3))(4) phosphors and matching blue-emitting phosphors. The results indicate that the quality of the brightness and color reproduction is suitable for application in shortwave UV fluorescent lamps. The white-light fluorescent lamp displays CIE chromaticity coordinates of x = 0.33, y = 0.35, a warm white light with a correlated color temperature of 5646 K, and a color-rendering index of Ra = 70.

The effect of some factors on Ms and SME in Ce-TZP ceramics

International Nuclear Information System (INIS)

Jiang, B.; Tu, J.; Hsu, T.Y.; Qi, X.; Zheng, X.; Zhong, J.

1992-01-01

As known to all, shape memory behaviour has been observed in a variety of metallic alloys. This phenomenon, however, is not only observed in that field but also in other materials recently, such as in polymers, intermetallic compounds and ceramics, especially in zirconia ceramics. Swain observed the shape recovery of a bent magnesia-partially-stabilized zirconia (Mg-PSZ) bar upon heating above a certain temperature. The maximum deflection which was nearly completely recovered on heating is about 300 μm. Chen et al., investigated the pseudoelasticity and shape memory effect (SME) in ceria-stabilized tetragonal zirconia polycrystals (Ce-TZP) containing 12 mol% CeO 2 . Wang et al., also observed the SME in Ce-TZP containing 10 mol% CeO 2 . In this paper, the authors would like to introduce some of results conducted recently in our group on SME in Ce-TZP ceramics

A new type of Ce-Mo based conversion coatings for aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Li Di; Li Guoqiang; Guo Baolan; Peng Mingxia [Coll. of Materials Science and Engineering, Beijing Univ. of Aeronautics and Astronautics, Beijing, BJ (China)

2002-07-01

A new type of process for forming Ce-Mo conversion coatings on Al-alloys has been developed. Conversion coatings about 3.6 {mu}m thickness were obtained by immersing Al-alloys for 20 minutes in boiling film forming solutions containing (NH{sub 4}){sub 2}Ce(NO{sub 3}){sub 6} 2.5 g/l, NaKC{sub 4}H{sub 4}O{sub 6}.4H{sub 2}O 2.5 g/l, Na{sub 2}CO{sub 3} 7.5 g/l and Na{sub 2}MoO{sub 4} 5.0 g/l. In the case of LF4 Al-alloy, polarization curves and immersion tests in 5% NaCl indicated that the conversion coatings exhibited more excellent resistance to localized corrosion than the conventional chromate conversion coatings. However, its resistance to localized corrosion was not satisfactory on LC4 Al alloy. Scanning electron microscopy (SEM) and energy dispersion analyzer of X-ray (EDAX) analysis revealed that the conversion coatings having complex surface microstructure on both LC4 and LF6 Al alloys consist mainly of O, Al and other alloying elements in addition to significant Ce and Mo. A mechanism of film formation was proposed to explain the experimental results. (orig.)

ELEKTRİKLİ EV ALETLERİNDE CE UYUMLULUĞU VE BİR UYGULAMA

Directory of Open Access Journals (Sweden)

Nazmi EKREN

2009-01-01

Full Text Available Hızla gelişen teknoloji, artan rekabet ortamı ve kullanıcının bilinçlenmesi gibi nedenlerden dolayı kaliteli üretim yapmanın gerekliliği günümüzde daha da artmıştır. Ürün kalitesinin ve güvenilirliğinin belgelenmesi tüketici açısından şart olmuştur. Ürün güvenliğinin belgelenmesinde kullanılan birçok belge vardır. Bu belgelerden biri de CE belgesidir. Bu makalede, CE işareti ile ilgili temel bilgi verilmiş ve elektrikli ev aletleri için gerekli CE standartları ve testlerinden bahsedilmiştir. Örnek olarak elektrikli ev aletlerinden tost makinesi ele alınmış, incelenmiştir. Tost makinesine CE belgesi almak için EN60335-2-9 direktifine göre gerekli testler yapılmış ve CE belgesi alınmıştır.

Improvement of photoluminescence properties and thermal stability of Y{sub 2.9}Ce{sub 0.1}Al{sub 5−x}Si{sub x}O{sub 12} phosphors with Si{sub 3}N{sub 4} addition

Energy Technology Data Exchange (ETDEWEB)

Zhang, Fangfang [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Song, Kaixin, E-mail: kxsong@hdu.edu.cn [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Jiang, Jun [Ningbo Institute of Materials Technologies and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Wu, Song; Zheng, Peng [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China); Huang, Qingming [Instrument Analysis and Testing Center, Fuzhou University, Fuzhou 350002 (China); Xu, Junming; Qin, Huibin [College of Electronic Information and Engineering, Hangzhou Dianzi University, Hangzhou 310018 (China)

2014-12-05

Highlights: • Y{sub 2.9}Ce{sub 0.1}Al{sub 5−x}Si{sub x}O{sub 12} phosphors were prepared by solid-state reaction in reduced air ambience. • Si{sup 4+} could be incorporated into the host lattice of Y{sub 3}Al{sub 5}O{sub 12} through partial occupation of the Al{sup 3+} sites. • Si{sub 3}N{sub 4} addition can improve photoluminescence efficiency and thermal stability of Y{sub 3}Al{sub 5}O{sub 12}:Ce. - Abstract: A series of Si{sub 3}N{sub 4} doping Y{sub 2.9}Ce{sub 0.1}Al{sub 5−x}Si{sub x}O{sub 12−3x/2}N{sub 4x/3} phosphors were prepared by solid-state reaction in 95%N{sub 2}–5%H{sub 2} reduced air ambience. The XRD characteristics plus Rietveld refinement results shows that the as-sintered powders are unique crystal phase with the same crystal structure of Y{sub 3}Al{sub 5}O{sub 12} (PDF No. 79-1891). The N element was not detected by the analysis of X-ray photoelectron spectroscopy (XPS) and energy dispersive X-ray spectrum (EDS). The photoluminescence spectra (PL and PLE) tests show that the exciting and emitting intensity of PLE and PL gradually increase due to the increase of Si{sub 3}N{sub 4} concentration. Meanwhile, the phosphorescence decay times are prolonged from 45 ns (x = 0) to 78 ns (x = 0.3), under the monitor of 530 nm wavelength. The thermoluminescence tests (TL) confirm the thermal stability of as-phosphors with Si{sub 3}N{sub 4} addition is much better than that of the pristine Y{sub 2.9}Ce{sub 0.1}Al{sub 5}O{sub 12} phosphors.

Microstructure and mechanical properties of Al-Si-X alloys fabricated by gas atomization and extrusion process

International Nuclear Information System (INIS)

Lee, T.H.; Hong, S.J.

2009-01-01

In order to develop good wear resistant and high-strength alloys, Al 81 Si 19 alloy was reinforced with transition elements such as Ni and Ce. The solubility of Si in aluminum was amplified, with increasing the Ni and Ce content in the rapidly solidified powders. The extruded bars consist of homogeneously dispersed fine Si particles along with Al 3 Ni and Al 3 Ce compounds (30-120 nm) in aluminum matrix (grain size below 500 nm). The tensile strength at room temperature for Al 81 Si 19 , Al 78 Si 19 Ni 2 Ce 0.5 and Al 76 Si 19 Ni 4 Ce 1 bars extruded at 400 deg. C was estimated as 281, 521, and 668 MPa, respectively. In addition, the maximum tensile strength of 730 MPa was attained in Al 73 Si 19 Ni 7 Ce 1 bulk alloy. The uniform dispersion of precipitates (Si, Al 3 Ni and Al 3 Ce particles) from the supersaturated Al matrix of ternary and quaternary alloys after extrusion was effective for enhanced mechanical properties.

Luminescence rise time in self-activated PbWO4 and Ce-doped Gd3Al2Ga3O12 scintillation crystals

CERN Document Server

E. Auffray; A. Borisevich; V. Gulbinas; A. Fedorov; M. Korjik; M.T. Lucchini; V. Mechinsky; S. Nargelas; E. Songaila; G. Tamulaitis; A. Vaitkevičius; S. Zazubovich

2016-01-01

The time resolution of scintillation detectors of ionizing radiation is one of the key parameters sought for in the current and future high-energy physics experiments. This study is encouraged by the necessity to find novel detection methods enabling a sub-10-ps time resolution in scintillation detectors and is focused on the exploitation of fast luminescence rise front. Time-resolved photoluminescence (PL) spectroscopy and thermally stimulated luminescence techniques have been used to study two promising scintillators: self-activated lead tungstate (PWO, PbWO4) and Ce-doped gadolinium aluminum gallium garnet (GAGG, Gd3Al2Ga3O12). A sub-picosecond PL rise time is observed in PWO, while longer processes in the PL response in GAGG:Ce are detected and studied. The mechanisms responsible for the PL rise time in self-activated and doped scintillators are under discussion.

L-Arginine-Triggered Self-Assembly of CeO2 Nanosheaths on Palladium Nanoparticles in Water.

Science.gov (United States)

Wang, Xiao; Zhang, Yibo; Song, Shuyan; Yang, Xiangguang; Wang, Zhuo; Jin, Rongchao; Zhang, Hongjie

2016-03-24

Pd@CeO2 core-shell nanostructures with a tunable Pd core size, shape, and nanostructure as well as a tunable CeO2 sheath thickness were obtained by a biomolecule-assisted method. The synthetic process is simple and green, as it involves only the heating of a mixture of Ce(NO3 )3 , l-arginine, and preformed Pd seeds in water without additives. Importantly, the synthesis is free of thiol groups and halide ions, thus providing a possible solution to the problem of secondary pollution by Pd nanoparticles in the sheath-coating process. The Pd/CeO2 nanostructures can be composited well with γ-Al2 O3 to create a heterogeneous catalyst. In subsequent tests of catalytic NO reduction by CO, Pd@CeO2 /Al2 O3 samples based on Pd cubes (6, 10, and 18 nm), Pd octahedra (6 nm), and Pd cuboctahedra (9 nm) as well as a simply loaded Pd cube (6 nm)-CeO2 /Al2 O3 sample were used as catalysts to investigate the effects of the Pd core size and shape and the hybrid nanostructure on the catalytic performance. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Luminescence properties of the Mg co–doped Ce:SrHfO_3 ceramics prepared by the Spark Plasma Sintering Method

International Nuclear Information System (INIS)

Chiba, Hiroyuki; Kurosawa, Shunsuke; Harata, Koichi; Murakami, Rikito; Yamaji, Akihiro; Ohashi, Yuji; Pejchal, Jan; Kamada, Kei; Yokota, Yuui; Yoshikawa, Akira

2016-01-01

1300 or 1400 °C pre–sintered Al/Ce/Mg:SrHfO_3 and Al/Ce:SrHfO_3 ceramics were prepared by the Spark Plasma Sintering (SPS) in order to search for a new scintillation material with a high–effective atomic number(Z_e_f_f) and good light output. The SrHfO_3 has a high Z_e_f_f of 60, and high gamma–ray detection efficiency is expected. Meanwhile it has a high melting point of over 2500 °C, and single crystal is hard to be grown. On the other hand, high melting materials can be prepared as ceramics, and the SPS method is a simple process to fabricate the ceramics within a few hours. Thus, we prepared the samples using the SPS method, and their optical and scintillation properties were investigated. We found that Al/Ce/Mg:SrHfO_3 and Al/Ce:SrHfO_3 ceramics had an emission wavelength at around 400 nm originating from 5d–4f transition of Ce"3"+. Moreover, Al/Ce/Mg:SrHfO_3 pre-sintered at a temperature of 1400 °C had a light output of approximately 5,000 ph/MeV. In this paper, the light output of Mg-co-doped samples was improved compared with the Mg-free ones. The light output also depends on the pre-sintering temperature. - Highlights: • Luminescence Properties of Al/Ce/Mg:SrHfO_3 ceramics scintillator was investigated. • These ceramics were prepared by the Spark Plasma Sintering Method. • Light output of the Al/Ce/Mg:SrHfO_3 ceramics was approximately 5,000 ph/MeV.

Estrategias vinculadas a la atención de los estudiantes universitarios con discapacidad

Directory of Open Access Journals (Sweden)

Elaineth Abasali

2018-01-01

Full Text Available El objetivo de este estudio fue desarrollar estrategias instruccionales vinculadas a la atención de estudiantes universitarios con discapacidad, pertenecientes a la UPEL-IPC. La metodología estuvo constituida por un proyecto factible, con investigación de campo, documental y no experimental, se abordó el Modelo General de Desarrollo Tecnológico (MGDT de Szczurek (1990, el cual está constituido por cuatro fases: Estudio de Necesidades, Diseño de la Solución, Implantación y Evaluación. Los sujetos de investigación fueron  16 estudiantes con discapacidad, y 19 profesores del Departamento de Tecnología Educativa del IPC. En la implantación se ejecutó el diseño de la solución, obteniéndose resultados favorables, y posteriormente se procedió a la evaluación de todas las fases.

Cold white light generation through the simultaneous emission from Ce{sup 3+}, Dy{sup 3+} and Mn{sup 2+} in 90Al{sub 2}O{sub 3}{center_dot}2CeCl{sub 3}{center_dot}3DyCl{sub 3}{center_dot}5MnCl{sub 2} thin film

Energy Technology Data Exchange (ETDEWEB)

Gonzalez, W. [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, P.O. Box 55-534, Mexico, D.F. 09340 (Mexico); Alvarez, E. [Departamento de Fisica, Universidad de Sonora (UNISON), Boulevard Luis Encinas y Rosales s/n, Hermosillo, Sonora 83000 (Mexico); Martinez-Martinez, R.; Yescas-Mendoza, E. [Instituto de Fisica y Matematicas, Universidad Tecnologica de la Mixteca, Carretera a Acatlima Km. 2.5, Huajuapan de Leon, Oaxaca 69000 (Mexico); Camarillo, I. [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, P.O. Box 55-534, Mexico, D.F. 09340 (Mexico); Caldino, U., E-mail: cald@xanum.uam.mx [Departamento de Fisica, Universidad Autonoma Metropolitana-Iztapalapa, P.O. Box 55-534, Mexico, D.F. 09340 (Mexico)

2012-08-15

The photoluminescence of a CeCl{sub 3}, DyCl{sub 3} and MnCl{sub 2} doped aluminum oxide film deposited by ultrasonic spray pyrolysis was characterized by excitation, emission and decay time spectroscopy. A nonradiative energy transfer from Ce{sup 3+} to Dy{sup 3+} and Mn{sup 2+} is observed upon UV excitation at 278 nm (peak emission wavelength of AlGaN-based LEDs). Such energy transfer leads to a simultaneous emission of these ions in the blue, green, yellow and red regions, resulting in white light emission with CIE1931 chromaticity coordinates, x=0.34 and y=0.23, which correspond to cold white light with a color temperature of 4900 K. - Highlights: Black-Right-Pointing-Pointer 90Al{sub 2}O{sub 3}{center_dot}2CeCl{sub 3}{center_dot}3DyCl{sub 3}{center_dot}5MnCl{sub 2} thin film (AOCDM) could be prepared by spray pyrolysis. Black-Right-Pointing-Pointer Non-radiative energy transfer from Ce{sup 3+} to Dy{sup 3+} and Mn{sup 2+} takes place in AOCDM. Black-Right-Pointing-Pointer AOCDM (pumped with 278 nm-UV light) can generate 4900 K cold white light.

The equiatomic intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and magnetic properties of CeAuCd

Energy Technology Data Exchange (ETDEWEB)

Johnscher, Michael; Niehaus, Oliver; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Tappe, Frank [Hochschule Hamm-Lippstadt, Hamm (Germany)

2015-06-01

The cadmium intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and CeAuCd were synthesized by induction-melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. The samples were characterized by powder X-ray diffraction. The structures of CePtCd (ZrNiAl type, P anti 62m, a = 763.8(6), c = 409.1(4) pm, wR2 = 0.0195, 298 F{sup 2} values, 14 variables) and EuPtCd (TiNiSi type, Pnma, a = 741.3(2), b = 436.4(1), c = 858.0(4) pm, wR2 = 0.0385, 440 F{sup 2} values, 20 variables) were refined from single-crystal data. The REPtCd structures exhibit three-dimensional networks of corner- and edge-sharing Cd rate at Pt{sub 2/6}Pt{sub 2/3} and Cd rate at Pt{sub 4/4} tetrahedra, which leave cages for the rare earth atoms. Temperature-dependent magnetic susceptibility data of CeAuCd reveal a paramagnetic to antiferromagnetic phase transition at T{sub N} = 3.7(5) K.

The equiatomic intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and magnetic properties of CeAuCd

International Nuclear Information System (INIS)

Johnscher, Michael; Niehaus, Oliver; Poettgen, Rainer

2015-01-01

The cadmium intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and CeAuCd were synthesized by induction-melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. The samples were characterized by powder X-ray diffraction. The structures of CePtCd (ZrNiAl type, P anti 62m, a = 763.8(6), c = 409.1(4) pm, wR2 = 0.0195, 298 F 2 values, 14 variables) and EuPtCd (TiNiSi type, Pnma, a = 741.3(2), b = 436.4(1), c = 858.0(4) pm, wR2 = 0.0385, 440 F 2 values, 20 variables) were refined from single-crystal data. The REPtCd structures exhibit three-dimensional networks of corner- and edge-sharing Cd rate at Pt 2/6 Pt 2/3 and Cd rate at Pt 4/4 tetrahedra, which leave cages for the rare earth atoms. Temperature-dependent magnetic susceptibility data of CeAuCd reveal a paramagnetic to antiferromagnetic phase transition at T N = 3.7(5) K.

Redefinición de competencias vinculadas a la productividad

Directory of Open Access Journals (Sweden)

José María Romero Rodríguez

2016-08-01

Full Text Available La formación por competencias ha adquirido un papel relevante en las últimas décadas. Entre otros aspectos de este enfoque, se han relacionado con la productividad en las empresas. En este momento, es pertinente una revisión de aquellas competencias transversales que pueden vincularse con la productividad y que pueden abrir nuevas perspectivas de estudio de este campo. Este artículo es el resultado de una revisión de la literatura existente sobre competencias profesionales y productividad empresarial en las bases de datos ProQuest, ERIC, ISOC y Dialnet. Mediante la confrontación de tres listados distintos de competencias obtenidos en la revisión de la literatura, se ha generado un único listado con 25 competencias transversales y la definición de las mismas, para su aplicación en futuras investigaciones, gestión del personal en las organizaciones y el posible establecimiento de planes formativos para transmitir aquellas competencias productivas. Los resultados de la revisión bibliográfica realizada posibilitan nuevas aproximaciones a la identificación de competencias, ofreciendo un listado actualizado de las competencias transversales vinculadas a la productividad que coinciden con las aportadas en otras investigaciones realizadas sobre competencias predictivas de un rendimiento eficaz, competencias para la empleabilidad y competencias en Formación Profesional del área de Servicios Socioculturales y a la Comunidad.

Recovery Ce from Ce - TBP Used Oxalic Acid

International Nuclear Information System (INIS)

Purwani, MV; Subagiono, R.; Suyanti

2007-01-01

Recovery or stripping Ce from Ce - TBP product of monazite sand used oxalic acid. Ce - TBP as organic phase and oxalic acid as aqueous phase and as strong precipitant compound to precipitate metal element. The stripping product as Ce - oxalic precipitate. The influence parameter were percentage of oxalic acid, volume ratio of Ce-TBP with oxalic acid, time and rate of stripping. At stripping of 25 ml Ce - TBP used oxalic acid, the optimum condition were achieve at using 5% oxalic acid, volume ratio of Ce - TBP : 5% oxalic acid = 1 : 1, time of stripping 7.5 minute and rate of stripping 150 rpm. At the optimum condition was obtained the recovery efficiency was 100%. (author)

Isothermal sections at 500 deg C of the Dy-V-Al and Dy-Cr-Al systems in the aluminium rich regions

International Nuclear Information System (INIS)

Rykhal', R.M.; Zarechnyuk, O.S.; Mats'kiv, O.P.

1979-01-01

X-ray diffraction and microscopic analyses have been used to investigate the ternary system dysprosium-vanadium-aluminium in the aluminium rich region. In the system Dy-V-Al two ternary compounds have been found: DyV 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.54 A and approximately DyVAl 8 (hexagonal crystal system, structure unknown, a=10.86, c=17.71 A, c/a=1.631). In the system dysprosium-chromium-aluminium three ternary compounds have been found: DyCr 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.39), approximately equal to DyCrAl 8 ) hexagonal crystal system, structure type unkown a=10.75, c=17.60 A, c/a=1.637) and DyCr 4 Al 8 (tetragonal structure, CeMn 4 Al 8 type, a=8.87, c=5.04 A, c/a=0.568). Isothermal sections of the systems Dy-V-Al and Dy-Cr-Al have been plotted at 500 deg C

Traducerea: între ce se poate traduce și ce trebuie tradus

Directory of Open Access Journals (Sweden)

Magda Jeanrenaud

2016-02-01

Full Text Available Pornind de la o tulburătoare interpretare a lui Jacques Derrida, studiul de față își propune să investigheze și încearcă să explice blocajul ce intervine în versiunile englezești, franceze și românești (semnate de Antoine Berman, Alexis Nouss, Steven Rendall, Catrinel Pleșu etc. ale celebrului text al lui Walter Benjamin, Die Aufgabe des Übersetzers, atunci cînd traducătorii transpun în cele trei limbi țintă cele două citate cuprinse în acesta: un citat din Mallarmé, lăsat netradus de Benjamin însuși, și un altul, din Pannwitz. Într-un fel sau altul, ambele citate au o formă discursivă ce lasă să se întrevadă o sintaxă ce se abate deliberat de la normă, ca și cum ar fi deja niște „traduceri”. Analiza mai pune în evidență și comportamentul (cumva o dominantă a psihologiei traducătorilor? celor ce au transpus textul benjaminian, comportament marcat de obsesia lizibilității văzută ca o trăsătură congenitală a oricărei traduceri, chiar și atunci cînd textul original nu tinde spre aceasta. De unde și dilema, dureroasă, legată de spinoasa chestiune a intenționalității textului (nu doar de tradus...

Design of Rh/Ce0.2Zr0.8O2-Al2O3 nanocomposite for ethanol steam reforming

International Nuclear Information System (INIS)

De Rogatis, Loredana; Montini, Tiziano; Casula, Maria F.; Fornasiero, Paolo

2008-01-01

Rh(1 wt.%)/Ce 0.2 Zr 0.8 O 2 (10 wt.%)-Al 2 O 3 nanocomposite has been investigated as active and thermally stable catalyst for ethanol steam reforming. Rh nanoparticles were synthesised by surfactant assisted route, using N-hexadecyl-N-(2-hydroxyethyl)-N,N-dimethyl ammonium bromide (HEAC16Br). Metal particles with average diameter of 2.1 nm were obtained at 0.53 Rh/HEAC16Br molar ratio, while increasing the amount of surfactant lead to formation of larger particles. The preformed Rh nanoparticles have been effectively embedded into a porous layer of nanocomposite oxides. Low temperature H 2 chemisorption experiments and activity data confirm that most of the Rh atoms are accessible to the reaction mixture. The Ce 0.2 Zr 0.8 O 2 mixed oxide inhibits the dehydration of ethanol to ethylene and favours the water gas shift reaction. The alumina ensures good thermal stability and high surface area of the catalyst. No significant deactivation is observed after repeated run-up and run-down experiments

Actividades físico-recreativas vinculadas al ajedrez para la ocupación del tiempo libre de niños entre 8-10 años de la Circunscripción 34 del Consejo Popular “Hermanos Barcón” del municipio Pinar del Río

Directory of Open Access Journals (Sweden)

Marisel Piñeiro Gomez

2009-06-01

Full Text Available Tomando como sustento que la comunidad resulta un contexto importante del trabajo social por ser en ella donde se dinamizan los procesos de participación para reafirmar los valores, la identidad es que se pretende proponer un conjunto de  actividades  físico  recreativas  vinculadas  al  ajedrez  para  la  ocupación  del tiempo libre de los niños y niñas entre 8/10 años de la Circunscripción 34 del Consejo Popular “Hermanos Barcón” del      municipio Pinar del Río. Sonrelacionadas con el ajedrez teniendo en consideración que sus propósitos generales están encaminados a desarrollar en el individuo una actitud favorable hacia el ajedrez que permita apreciarlo como elemento generador de cultura; desplegar su potencial intelectual a partir del estímulo de la esfera cognitiva; garantizar la adquisición de conocimientos, habilidades y destrezas básicas necesarias para la incorporación a la vida activa; permitir el establecimiento de vínculos entre los conocimientos, experiencias ajedrecistas y la vida cotidiana. Se realizó con una unidad de análisis desglosada en  32 del sexo masculino (39,5% y 49 del femenino (60,4%; para la muestra se escogieron a los niños y niñas que deseaban  ocupar  su  tiempo  libre  con  la  realización  de  actividades  físico recreativas vinculadas al ajedrez, quedando como sigue: Sexo masculino: 19 (59,3%  de  la  población; 79,1%  de  la  unidad  de  análisis, sexo  femenino: 23 (46,9% de la población; 63,8% de la unidad de análisis. La importancia de este trabajo es que fomentará hábitos de salud, disciplina, compañerismo, cooperación, responsabilidad; desarrollará habilidades de liderazgo; favorecerá a la integración, la comprensión, reconocimiento, desarrollo de agilidad mental, la capacidad para la solución de problemas, la creatividad, imaginación, curiosidad infantil, permitirá intercambiar ideas y experiencias durante su desarrollo.

A comparative UV-vis-diffuse reflectance study on the location and interaction of cerium ions in Al- and Zr-pillared montmorillonite clays

International Nuclear Information System (INIS)

Rao, G. Ranga; Mishra, Braja Gopal

2005-01-01

The environment, location and interaction of the Ce 3+ ions in the micropores of Al- and Zr-pillared clays have been studied by UV-vis-diffuse reflectance spectroscopy (UV-vis-DRS). The DRS spectra show that the chemical environment of the Ce 3+ ions in cerium exchanged clay is different from that of the Al- and Zr-pillared clays. The Al-Ce pillared clays (Al-Ce-PM) show four distinct absorption bands at 224, 263, 294 and 342 nm in the UV region which are attributed to 4f → 5d interconfigurational transitions of Ce 3+ ions associated with alumina pillars. The O 2- → Ce 3+ charge transfer band observed at 263 nm for Ce-exchanged and Al-Ce-PM clays is blue shifted by 10 nm for Ce-Zr-pillared clays (Ce-Zr-PM) due to fully hydrated Ce 3+ ions. The Ce 3+ ions are incorporated in the Al- and Zr-pillars possibly as AlCeO 3 and Ce x Zr 1-x O 2 particles upon heat treatment

Hydrocracking of cumene over Ni/Al 2O 3 as influenced by CeO 2 doping and γ-irradiation

Science.gov (United States)

El-Shobaky, G. A.; Doheim, M. M.; Ghozza, A. M.

2004-01-01

Cumene hydrocracking was carried out over pure and doped Ni/Al 2O 3 solids and also, on these solids after exposure to different doses of γ-rays between 0.4 and 1.6 MGy. The dopant concentration was varied between 1 and 4 mol% CeO 2. Pure and doped samples were subjected to heat treatment at 400°C and cumene hydrocracking reaction was carried out using various solids at temperatures between 250°C and 400°C by means of micropulse technique. The results showed that both CeO 2 doping and γ-irradiation of the investigated system brought about an increase in its specific surface area. γ-irradiation of pure samples increased their catalytic activities effectively. However, the doping caused a decrease in the catalytic activity. γ-irradiation of the doped samples brought about a net decrease in the catalytic activity. The catalytic reaction products over different investigated solids were ethylbenzene as a major product together with different amounts of toluene, benzene and C 1-C 3 gaseous hydrocarbons. The selectivity towards the formation of various reaction products varies with the reaction temperature, doping and γ-irradiation.

Effective corrosion protection of AA6061 aluminum alloy by sputtered Al-Ce coatings

International Nuclear Information System (INIS)

Dominguez-Crespo, M.A.; Torres-Huerta, A.M.; Rodil, S.E.; Ramirez-Meneses, E.; Suarez-Velazquez, G.G.; Hernandez-Perez, M.A.

2009-01-01

Al-Ce coatings were deposited on silicon and AA6061 aluminum alloy substrates by DC magnetron sputtering using aluminum in combination with pure cerium targets. The materials were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and electrochemical impedance spectroscopy (EIS) in order to consider their application as high corrosion resistance coatings. The corrosion behavior of the films was studied using a NaCl aqueous solution (3.5 wt%). As for the characterization results, an apparent amorphous phase of aluminum oxide with small cerium compounds embedded in the matrix was detected by the X-ray diffraction patterns and HRTEM on the deposited films at 200 W and 4 Pa. At these conditions, AFM and SEM images evidenced crack-free coatings with low-roughness nanometric structures and columnar growth. EIS and Tafel results converged to indicate an inhibition of the corrosion reactions. The film displayed good stability in the aggressive medium and after 1 day of exposure underwent very little degradation. The variations in the impedance and Tafel characteristics were found to occur as a function of cerium content, which provokes important changes in the film protective properties.

Effective corrosion protection of AA6061 aluminum alloy by sputtered Al-Ce coatings

Energy Technology Data Exchange (ETDEWEB)

Dominguez-Crespo, M.A., E-mail: mdominguezc@ipn.m [Instituto Politecnico Nacional, GIPMAT CICATA-Altamira, km 14.5, Carretera Tampico-Puerto Industrial Altamira, C.P. 89600 Altamira, Tamps (Mexico); Torres-Huerta, A.M. [Instituto Politecnico Nacional, GIPMAT CICATA-Altamira, km 14.5, Carretera Tampico-Puerto Industrial Altamira, C.P. 89600 Altamira, Tamps (Mexico); Rodil, S.E. [Instituto de Investigacion en Materiales, Universidad Nacional Autonoma de Mexico, Circuito Exterior s/n, Ciudad Universitaria, Del. Coyoacan, C.P. 04510 Mexico, D.F. (Mexico); Ramirez-Meneses, E. [Instituto Politecnico Nacional, GIPMAT CICATA-Altamira, km 14.5, Carretera Tampico-Puerto Industrial Altamira, C.P. 89600 Altamira, Tamps (Mexico); Suarez-Velazquez, G.G. [Alumna del PTA del CICATA-Altamira IPN, km 14.5, Carretera Tampico-Puerto Industrial Altamira, C.P. 89600 Altamira, Tamps (Mexico); Hernandez-Perez, M.A. [Instituto Politecnico Nacional, ESIQIE, C.P. 07738 Mexico, D.F. (Mexico)

2009-12-30

Al-Ce coatings were deposited on silicon and AA6061 aluminum alloy substrates by DC magnetron sputtering using aluminum in combination with pure cerium targets. The materials were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and electrochemical impedance spectroscopy (EIS) in order to consider their application as high corrosion resistance coatings. The corrosion behavior of the films was studied using a NaCl aqueous solution (3.5 wt%). As for the characterization results, an apparent amorphous phase of aluminum oxide with small cerium compounds embedded in the matrix was detected by the X-ray diffraction patterns and HRTEM on the deposited films at 200 W and 4 Pa. At these conditions, AFM and SEM images evidenced crack-free coatings with low-roughness nanometric structures and columnar growth. EIS and Tafel results converged to indicate an inhibition of the corrosion reactions. The film displayed good stability in the aggressive medium and after 1 day of exposure underwent very little degradation. The variations in the impedance and Tafel characteristics were found to occur as a function of cerium content, which provokes important changes in the film protective properties.

Environmental risk assessment of engineered nano-SiO2 , nano iron oxides, nano-CeO2 , nano-Al2 O3 , and quantum dots.

Science.gov (United States)

Wang, Yan; Nowack, Bernd

2018-05-01

Many research studies have endeavored to investigate the ecotoxicological hazards of engineered nanomaterials (ENMs). However, little is known regarding the actual environmental risks of ENMs, combining both hazard and exposure data. The aim of the present study was to quantify the environmental risks for nano-Al 2 O 3 , nano-SiO 2 , nano iron oxides, nano-CeO 2 , and quantum dots by comparing the predicted environmental concentrations (PECs) with the predicted-no-effect concentrations (PNECs). The PEC values of these 5 ENMs in freshwaters in 2020 for northern Europe and southeastern Europe were taken from a published dynamic probabilistic material flow analysis model. The PNEC values were calculated using probabilistic species sensitivity distribution (SSD). The order of the PNEC values was quantum dots nano-CeO 2  nano iron oxides nano-Al 2 O 3  nano-SiO 2 . The risks posed by these 5 ENMs were demonstrated to be in the reverse order: nano-Al 2 O 3  > nano-SiO 2  > nano iron oxides > nano-CeO 2  > quantum dots. However, all risk characterization values are 4 to 8 orders of magnitude lower than 1, and no risk was therefore predicted for any of the investigated ENMs at the estimated release level in 2020. Compared to static models, the dynamic material flow model allowed us to use PEC values based on a more complex parameterization, considering a dynamic input over time and time-dependent release of ENMs. The probabilistic SSD approach makes it possible to include all available data to estimate hazards of ENMs by considering the whole range of variability between studies and material types. The risk-assessment approach is therefore able to handle the uncertainty and variability associated with the collected data. The results of the present study provide a scientific foundation for risk-based regulatory decisions of the investigated ENMs. Environ Toxicol Chem 2018;37:1387-1395. © 2018 SETAC. © 2018 SETAC.

Crystal structure of the Ce2Ni2Zn15 compound

International Nuclear Information System (INIS)

Opainich, I.M.; Pavlyuk, V.V.; Bodak, O.I.; Cherny, R.; Yvon, K.

1996-01-01

A structure of a new ternary compound of the composition Ce2Ni2Zn15 (sp.gr.R3-barm,a=0.9080(3) nm, c=1.3294(3) nm) was determined on single-crystal and powder specimens. The study was performed on a Philips PW1100 automatic diffractometer and a DRON-4.07 powder diffractometer. The Ce2Ni2Zn15 compound is crystallized in the Ce2Al2Co15 structure type with the aluminum positions being occupied by nickel and cobalt positions being occupied by zinc

Acetylene and carbon monoxide oxidation over a Pt/Rh/CeO2/γ-Al2O3 automotive exhaust gas catalyst: kinetic modelling of transient experiments

NARCIS (Netherlands)

Harmsen, J.M.A.; Hoebink, J.H.B.J.; Schouten, J.C.

2001-01-01

The transient kinetics of acetylene (C2H2) conversion by oxygen over a commercial Pt/Rh/CeO2/¿-Al2O3 three-way catalyst have been modelled. Experiments to validate the model were carried out in a fixed-bed reactor with two separate inlets, enabling alternate feeding of acetylene and oxygen.

Influence of substitution of La by Ce on the glass forming ability and crystallization behavior of Al–Ni–La alloys

International Nuclear Information System (INIS)

Zhang, Z.; Xiong, X.Z.; Zhou, W.; Li, J.F.

2013-01-01

Highlights: •Wedge-shaped samples were suction cast with casting conditions controlled. •Partial substitution of La by Ce decreases the GFA of Al 85.5 Ni 9.5 La 5 . •Partial substitution of La by Ce increases the GFA of other Al–Ni–La alloys. •The GFA was analyzed from the thermodynamic and topological points of view. -- Abstract: Wedge-shaped samples of Al–Ni–(La–Ce) alloys were suction cast under an identical preparation condition, and their glass forming abilities (GFAs) and crystallization behaviors were compared. It was revealed that the partial substitution of La by Ce decreases the GFA of Al 85.5 Ni 9.5 La 5 alloy but increases the GFAs of Al 87.5 Ni 7.5 La 5 , Al 86.5 Ni 8.5 La 5 , Al 86 Ni 9 La 5 and Al 86 Ni 9.5 La 4.5 alloys. Meantime the crystallization behavior significantly changes. The optimal substitution content of La for glass formation depends on the composition of the base alloy. The lower the Ni content in the base alloy, the more the La content to be substituted. The GFA change with the substitution content is determined by the atomic packing efficiencies of the La (Ce)-centered clusters

Effect of Si and Co on the crystallization of Al-Ni-RE amorphous alloys

Energy Technology Data Exchange (ETDEWEB)

Wang, S.H. [Key Lab of Liquid structure and Heredity of Materials, Ministry of Education, South Campus of Shandong University, Jinan 250061 (China); Bian, X.F. [Key Lab of Liquid structure and Heredity of Materials, Ministry of Education, South Campus of Shandong University, Jinan 250061 (China)], E-mail: xfbian@sdu.edu.cn

2008-04-03

Crystallization of Al{sub 83}Ni{sub 10}Si{sub 2}Ce{sub 5}, Al{sub 85}Ni{sub 10}Ce{sub 5}, Al{sub 87}Ni{sub 7}Nd{sub 6} and Al{sub 87}Ni{sub 5}Co{sub 2}Nd{sub 6} amorphous alloys has been studied by using X-ray diffraction (XRD) and differential scanning calorimetry (DSC). The multiple transition metal (TM) (containing metalloid element) have significant effect on the crystallization behavior. A small addition of Si transforms a eutectic crystallization (Al{sub 85}Ni{sub 10}Ce{sub 5}) to a primary crystallization (Al{sub 83}Ni{sub 10}Si{sub 2}Ce{sub 5}); while a small addition of Co transforms a primary crystallization (Al{sub 87}Ni{sub 7}Nd{sub 6}) to a eutectic crystallization (Al{sub 87}Ni{sub 5}Co{sub 2}Nd{sub 6}). In addition, the activation energies for crystallization (E{sub a}) are obtained to be 191, 290, 221 and 166 kJ/mol for the Al{sub 83}Ni{sub 10}Si{sub 2}Ce{sub 5}, Al{sub 85}Ni{sub 10}Ce{sub 5}, Al{sub 87}Ni{sub 5}Co{sub 2}Nd{sub 6} and Al{sub 87}Ni{sub 7}Nd{sub 6} amorphous alloys based on the Kissinger method, respectively. It is found that the primary crystallization of fcc-Al is characteristic of a lower E{sub a}, as compared with eutectic crystallization.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

Energy Technology Data Exchange (ETDEWEB)

Lu, Zhao; Zhang, Lijun [Central South Univ., Changsha (China). State Key Lab of Powder Metallurgy; Tang, Ying [Thermo-Calc Software AB, Solna (Sweden)

2017-06-15

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Atomic mobility in liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys and its application to the simulation of solidification processes in RE-containing A357 alloys

International Nuclear Information System (INIS)

Lu, Zhao; Zhang, Lijun

2017-01-01

This paper first provides a critical review of experimental and theoretically-predicted diffusivities in both liquid and fcc Al-Si-Mg-RE (RE = Ce, Sc) alloys as-reported by previous researchers. The modified Sutherland equation is then employed to predict self- and impurity diffusivities in Al-Si-Mg-RE melts. The self-diffusivity of metastable fcc Sc is evaluated via the first-principles computed activation energy and semi-empirical relations. Based on the critically-reviewed and presently evaluated diffusivity information, atomic mobility descriptions for liquid and fcc phases in the Al-Si-Mg-RE systems are established by means of the Diffusion-Controlled TRAnsformation (DICTRA) software package. Comprehensive comparisons show that most of the measured and theoretically-predicted diffusivities can be reasonably reproduced by the present atomic mobility descriptions. The atomic mobility descriptions for liquid and fcc Al-Si-Mg-RE alloys are further validated by comparing the model-predicted differential scanning calorimetry curves for RE-containing A357 alloys during solidification against experimental data. Detailed analysis of the curves and microstructures in RE-free and RE-containing A357 alloys indicates that both Ce and Sc can serve as the grain refiner for A357 alloys, and that the grain refinement efficiency of Sc is much higher.

Natural gas reforming of carbon dioxide for syngas over Ni–Ce–Al catalysts

Energy Technology Data Exchange (ETDEWEB)

Han, Jun; Zhan, Yiqiu; Street, Jason; To, Filip; Yu, Fei

2017-07-01

A series of Ni–Ce–Al composite oxides with various Ni molar contents were synthesized via the refluxed co-precipitation method and used for natural gas reforming of CO₂ (NGRC) for syngas production. The effect of Ni molar content, reaction temperature, feed gas ratio and gas hourly space velocity (GHSV) on the Ni–Ce–Al catalytic performance was investigated. The Ni₁₀CeAl catalyst was selected to undergo 30 h stability test and the conversion of CH₄ and CO₂ decreased by 2.8% and 2.6%, respectively. The characterization of the reduced and used Ni10CeAl catalyst was performed using BET, H₂-TPR, in-situ XRD, TEM, and TGA-DTG techniques. The in-situ XRD results revealed that Ce₂O₃, CeO₂ and CeAlO₃ coexisted in the Ni10CeAl catalyst after reduction at 850 °C for 2 h. The results of the TEM analysis revealed that the Ni particle size increased after the NGRC reaction, which mainly caused the catalyst deactivation.

Luminescence rise time in self-activated PbWO{sub 4} and Ce-doped Gd{sub 3}Al{sub 2}Ga{sub 3}O{sub 12} scintillation crystals

Energy Technology Data Exchange (ETDEWEB)

Auffray, E. [CERN, Geneva (Switzerland); Augulis, R. [Center for Physical Sciences and Technology, Savanorių av. 231, Vilnius (Lithuania); Borisevich, A. [Research Institute for Nuclear Problems, Bobruiskaya str. 11, Minsk (Belarus); Gulbinas, V. [Center for Physical Sciences and Technology, Savanorių av. 231, Vilnius (Lithuania); Fedorov, A.; Korjik, M. [Research Institute for Nuclear Problems, Bobruiskaya str. 11, Minsk (Belarus); Lucchini, M.T. [CERN, Geneva (Switzerland); Mechinsky, V. [Research Institute for Nuclear Problems, Bobruiskaya str. 11, Minsk (Belarus); Nargelas, S. [Vilnius University, Universiteto str. 3, Vilnius (Lithuania); Songaila, E. [Center for Physical Sciences and Technology, Savanorių av. 231, Vilnius (Lithuania); Tamulaitis, G. [Vilnius University, Universiteto str. 3, Vilnius (Lithuania); Vaitkevičius, A., E-mail: augustas.vaitkevicius@ff.vu.lt [Vilnius University, Universiteto str. 3, Vilnius (Lithuania); Zazubovich, S. [Institute of Physics, University of Tartu, W. Ostwaldi Str. 1, Tartu (Estonia)

2016-10-15

The time resolution of scintillation detectors of ionizing radiation is one of the key parameters sought for in the current and future high-energy physics experiments. This study is encouraged by the necessity to find novel detection methods enabling a sub-10-ps time resolution in scintillation detectors and is focused on the exploitation of fast luminescence rise front. Time-resolved photoluminescence (PL) spectroscopy and thermally stimulated luminescence techniques have been used to study two promising scintillators: self-activated lead tungstate (PWO, PbWO{sub 4}) and Ce-doped gadolinium aluminum gallium garnet (GAGG, Gd{sub 3}Al{sub 2}Ga{sub 3}O{sub 12}). A sub-picosecond PL rise time is observed in PWO, while longer processes in the PL response in GAGG:Ce are detected and studied. The mechanisms responsible for the PL rise time in self-activated and doped scintillators are under discussion. - Highlights: • Photoluminescence rise time is studied in two scintillators: PWO and GAGG:Ce. • Sub-picosecond photoluminescence rise time in PWO is observed for the first time. • A multicomponent luminescence rise edge is observed in GAGG:Ce. • The mechanisms behind luminescence kinetics in the crystals are under discussion.

Luminescence properties of a single-component Na0.34Ca0.66Al1.66Si2.34O8:Ce3+, Sm3+ phosphor with tunable color tone for UV-pumped LEDs

Science.gov (United States)

Wang, Lei; Dong, Jie; Cui, Cai'e.; Tian, Yue; Huang, Ping

2015-08-01

A series of single-phase Na0.34Ca0.66Al1.66Si2.34O8:Ce3+, Sm3+ (NCASO) phosphors have been synthesized via a high temperature solid-state reaction method. The samples were studied based on photoluminescence (PL), photoluminescence excitation (PLE) spectra and fluorescence decay patterns. The obtained PLE exhibited a strong excitation band in the UV region between 250 and 380 nm. Under 340 nm excitation, NCASO:Ce3+, Sm3+ phosphor showed a broad emission band at 414 nm of Ce3+ and four emission bands from 550 nm to 725 nm of Sm3+. Spectra demonstrate nonradiative energy transfers (ET) occur from Ce3+-Sm3+. The analysis based on Inokuti-Hirayama model indicates that the ET is governed by electric dipole-dipole interaction. Moreover, the emitting colors can be adjusting from blue to white by proper tuning of the relative composition of Ce3+/Sm3+. These results show that NCASO:Ce3+, Sm3+ phosphors can be used as a potential single-phased white-emitting candidate for UV WLEDs.

Neutron diffraction study of the magnetic structures of CeMn2Ge2 and CeMn2Si2

International Nuclear Information System (INIS)

Fernandez-Baca, J.A.; Chakoumakos, B.C.; Hill, P.; Ali, N.

1995-01-01

The magnetic properties of the layered compounds of the form RMn 2 X 2 (R = Rare Earth, X = Si, Ge) have been thought to be sensitive to the intralayer Mn-Mn distance. Thus it has been reported that the Mn moments in CeMn 2 Si 2 are aligned antiferromagnetically (AF) below T N = 380K, while the Mn moments in CeMn 2 Ge 2 are ferromagnetic (FM) below T C = 316K. Recently, however, there has been some debate about the actual magnetic structures of this family of compounds, and for this reason the authors have performed high-resolution neutron powder diffraction measurements on these compounds for temperatures between 12K and 550K. The measurements indicate that at high temperatures both compounds are paramagnetic. Below T N = 380K CeMn 2 Si 2 becomes a collinear AF, with a structure similar to that reported by Siek et al. in which the magnetic propagation vector is τ = (0 0 1). CeMn 2 Ge 2 on the other hand, exhibits two different magnetic transitions. At T N ∼ 415K there is a transition to a collinear AF phase characterized by the commensurate propagation wavevector τ = (1 0 1). At T C = 318K there is a transition to a conical structure with a ferromagnetic component along the c-axis and a helical component in the ab plane. The helical component is characterized by the incommensurate propagation vector τ = (1 0 1-q z ), where q z is temperature dependent. These findings are consistent with the recent results of Welter et al

Structural and optical characteristics of Ce, Nd, Gd, and Dy-doped ...

Indian Academy of Sciences (India)

Ashwini S Varpe

2017-06-19

Jun 19, 2017 ... Al2O3-Gd. Al2O3-Dy. Figure 2. XRD patterns of RE:Al2O3 thin films for 5 mol% concentration of RE elements ... is due to more segregation of Ce3+ ions along the grain ..... to the split ground state into their 2F7/2 and 2F5/2.

NIR emission and Ce{sup 3+}–Nd{sup 3+} energy transfer in LaCaAl{sub 3}O{sub 7} phosphor prepared by combustion synthesis

Energy Technology Data Exchange (ETDEWEB)

Pathak, A.A. [National Power Training Institute, South Ambazari Road, Nagpur 440022 (India); Talewar, R.A., E-mail: talewarrupesh@gmail.com [Physics Department, Shri Ramdeobaba College of Engineering and Management, Katol Road, Nagpur 440013 (India); Joshi, C.P. [Physics Department, Shri Ramdeobaba College of Engineering and Management, Katol Road, Nagpur 440013 (India); Moharil, S.V. [Department of Physics, Rashtrasant Tukadoji Maharaj Nagpur University, Nagpur 440010 (India)

2016-11-15

Near infrared (NIR) emitting phosphor, LaCaAl{sub 3}O{sub 7}:Ce{sup 3+},Nd{sup 3+} was synthesized by one step combustion synthesis and characterized with scanning electron microscope, photoluminescence emission, photoluminescence excitation spectra and fluorescence decay measurements. When excited with UV, the phosphor gives broadband emission at 410 nm, which corresponds to the allowed 5d→4f transition of Ce{sup 3+} ions and an intense NIR emissions in the range 800–1400 nm, which are assigned to the characteristic transitions from {sup 4}I{sub 9/2,11/2,13/2} states of Nd{sup 3+} ions. The dependences of visible and NIR emissions, decay lifetime and the energy transfer efficiency (η{sub ETE}) on dopant concentrations were investigated in detail. The luminescence spectra, both in visible (VIS) and NIR regions, and decay curves of Ce{sup 3+} have been measured to prove energy transfer (ET) from Ce{sup 3+} to Nd{sup 3+}. These results demonstrate the possibility for enhancing the photovoltaic conversion efficiency of c-Si solar cell by modifying the absorption and utilizing the UV part of the solar spectrum where the efficiency of c-Si solar cell is low.

Influence of substitution of La by Ce on the glass forming ability and crystallization behavior of Al–Ni–La alloys

Energy Technology Data Exchange (ETDEWEB)

Zhang, Z.; Xiong, X.Z.; Zhou, W.; Li, J.F., E-mail: jfli@sjtu.edu.cn

2013-11-05

Highlights: •Wedge-shaped samples were suction cast with casting conditions controlled. •Partial substitution of La by Ce decreases the GFA of Al{sub 85.5}Ni{sub 9.5}La{sub 5}. •Partial substitution of La by Ce increases the GFA of other Al–Ni–La alloys. •The GFA was analyzed from the thermodynamic and topological points of view. -- Abstract: Wedge-shaped samples of Al–Ni–(La–Ce) alloys were suction cast under an identical preparation condition, and their glass forming abilities (GFAs) and crystallization behaviors were compared. It was revealed that the partial substitution of La by Ce decreases the GFA of Al{sub 85.5}Ni{sub 9.5}La{sub 5} alloy but increases the GFAs of Al{sub 87.5}Ni{sub 7.5}La{sub 5}, Al{sub 86.5}Ni{sub 8.5}La{sub 5}, Al{sub 86}Ni{sub 9}La{sub 5} and Al{sub 86}Ni{sub 9.5}La{sub 4.5} alloys. Meantime the crystallization behavior significantly changes. The optimal substitution content of La for glass formation depends on the composition of the base alloy. The lower the Ni content in the base alloy, the more the La content to be substituted. The GFA change with the substitution content is determined by the atomic packing efficiencies of the La (Ce)-centered clusters.

Influence of the sintering temperature on the Sr content in a Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 perovskite (x = 0.04–0.16) co-doped with Ce

International Nuclear Information System (INIS)

Kamel, Nour-el-hayet; Mouheb, Yasmina; Kamel, Ziane; Moudir, Dalila; Aouchiche, Fairouz; Arabi, Azeddine

2016-01-01

A Sr-Ce co-doped perovskite, with the chemical formula: Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 (y = 0.04, 0.08, 0.12 and 0.16, x = 0.05) is synthesized by sol–gel process. The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. The Sr amount sequestered in the perovskite reaches 85% (y = 0.16, 9.50 wt%) for Ts = 1373 K, giving sintering densities between 3.520 and 4.400. XRD analysis reveals an orthorhombic CaTiO_3 structure. The lattice parameters obey to Vegard’s law for Ts = 1373 and 1473 K. SEM analysis shows orthorhombic grains of 0.514 μm × 1 μm mean dimensions. MCC1 and MCC2 tests, performed on minerals sintered at 1373 K, indicate that the most durable one is that containing 9.50 wt% Sr. MCC1 test gave 6.998·10"−"6 g/cm"2 d of Sr, and MCC2 2.143·10"−"4 g/cm"2 d of Ce. The temperature favors the Sr dissolution to the detriment of Ce. The Ca dissolution rate reaches 1.002·10"−"6 to 2.005·10"−"6 g/cm"2 d. - Highlights: • Ca_(_1_−_x_−_y_)Ce_xSr_yAl_zTi_(_1_−_z_)O_3 perovskite is synthesized by sol–gel. • The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. • 85% of total Sr was sequestered in the perovskite for Ts = 1373 K. • MCC1 and MCC2 leach tests indicate that the most durable mineral is that containing 9.50 wt.% Sr. • MCC1 test gave 8.10 10"−"1"0 kg/m"2.d Sr. The lower is the leaching temperature the higher is the mineral durability.

An electron microscopy study of the effect of Ce on plasma sprayed bronze coatings

Science.gov (United States)

Wensheng, Li; Wang, S. C.; Ma, Chao; Zhiping, Wang

2012-07-01

The Cu-Al eutectoid alloy is an excellent material for mould due to its superior low friction. The conventional sand casting technique, however, is not feasible to fabricate high Al bronze because of high hardness and brittleness. Plasma arc spray has been used to produce high Al/Fe bronze coatings for mould. The inherent impurities such as H, O, N, S during the spray, however, may affect the coating's mechanical strength. One approach is to utilise the active rare earth Ce to clean up these impurities. The study is to investigate the effect of Ce on the microstructure, which has few reported in the literature.

Reduction in secondary dendrite arm spacing in cast eutectic Al-Si piston alloys by cerium addition

Science.gov (United States)

Ahmad, R.; Asmael, M. B. A.; Shahizan, N. R.; Gandouz, S.

2017-01-01

The effects of Ce on the secondary dendrite arm spacing (SDAS) and mechanical behavior of Al-Si-Cu-Mg alloys were investigated. The reduction of SDAS at different Ce concentrations was evaluated in a directional solidification experiment via computer-aided cooling curve thermal analysis (CA‒CCTA). The results showed that 0.1wt%-1.0wt% Ce addition resulted in a rapid solidification time, Δ t s, and low solidification temperature, Δ T S, whereas 0.1wt% Ce resulted in a fast solidification time, Δ t a-Al, of the α-Al phase. Furthermore, Ce addition refined the SDAS, which was reduced to approximately 36%. The mechanical properties of the alloys with and without Ce were investigated using tensile and hardness tests. The quality index ( Q) and ultimate tensile strength of (UTS) Al-Si-Cu-Mg alloys significantly improved with the addition of 0.1wt% Ce. Moreover, the base alloy hardness was improved with increasing Ce concentration.

REAuAl{sub 4}Ge{sub 2} and REAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (RE=rare earth element): Quaternary intermetallics grown in liquid aluminum

Energy Technology Data Exchange (ETDEWEB)

Xiuni, Wu [Department of Chemistry, Michigan State University, East Lansing, Michigan 48824 (United States); Kanatzidis, Mercouri G [Department of Chemistry, Michigan State University, East Lansing, Michigan 48824 (United States)

2005-11-15

The two families of intermetallic phases REAuAl{sub 4}Ge{sub 2} (1) (RE=Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Er, Tm and Yb) and REAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (2) (x=0.4) (RE=Ce and Eu) were obtained by the reactive combination of RE, Au and Ge in liquid aluminum. The structure of (1) adopts the space group R-3m (CeAuAl{sub 4}Ge{sub 2}, a=4.2384(7)A, c=31.613(7)A; NdAuAl{sub 4}Ge{sub 2}, a=4.2258(4)A, c=31.359(5)A; GdAuAl{sub 4}Ge{sub 2}, a=4.2123(6)A, c=30.994(6)A; ErAuAl{sub 4}Ge{sub 2}, a=4.2074(4)A, c=30.717(5)A). The structure of (2) adopts the tetragonal space group P4/mmm with lattice parameters: a=4.3134(8)A, c=8.371(3)A for EuAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4). Both structure types present slabs of ''AuAl{sub 4}Ge{sub 2}'' or ''AuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2}'' stacking along the c-axis with layers of RE atoms in between. Magnetic susceptibility measurements indicate that the RE atoms (except for Ce and Eu) possess magnetic moments consistent with +3 species. The Ce atoms in CeAuAl{sub 4}Ge{sub 2} and CeAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4) appear to be in a mixed +3/+4 valence state; DyAuAl{sub 4}Ge{sub 2} undergoes an antiferromagnetic transition at 11K and below this temperature exhibits metamagnetic behavior. The Eu atoms in EuAuAl{sub 4}(Au{sub x}Ge{sub 1-x}){sub 2} (x=0.4) appear to be in a 2+ oxidation state.

Time-resolved luminescent spectroscopy of YAG:Ce single crystal and single crystalline films

International Nuclear Information System (INIS)

Zorenko, Yu.; Gorbenko, V.; Savchyn, V.; Vozniak, T.; Puzikov, V.; Danko, A.; Nizhankovski, S.

2010-01-01

The peculiarities of the luminescence and energy transfer from YAG host to the emission centers formed by the Y Al antisite defects and Ce 3+ ions have been studied in YAG:Ce single crystals, grown from the melt by modified Bridgman method in Ar and CO 2 + H 2 atmospheres, and YAG:Ce single crystalline film, grown by liquid phase epitaxy method, using the comparative time-resolved luminescent spectroscopy under excitation by synchrotron radiation in the range of fundamental adsorption of this garnet.

Siderophore-mediated oxidation of Ce and fractionation of HREE by Mn (hydr)oxide-coprecipitation and sorption on MnO2: Experimental evidence for negative Ce-anomalies in abiogenic manganese precipitates

Science.gov (United States)

Krämer, Dennis; Tepe, Nathalie; Bau, Michael

2014-05-01

)oxides (e.g., Tanaka et al., 2010, Loges et al., 2012). Our experimental results demonstrate that biogenic organic ligands such as hydroxamate siderophores, may produce solutions with positive Ce anomaly (Bau et al., 2013) and may even counteract the surface oxidation of Ce on Mn (hydr)oxides. References Bau, M., Tepe, N., Mohwinkel, D., 2013. Siderophore-promoted transfer of rare earth elements and iron from volcanic ash into glacial meltwater, river and ocean water. Earth Planet. Sci. Lett. 364, 30-36. Christenson E. A. and Schijf J. (2011) Stability of YREE complexes with the trihydroxamate siderophore desferrioxamine B at seawater ionic strength. Geochim. Cosmochim. Acta 75, 7047-7062. Loges, A., Wagner, T., Barth, M., Bau, M., Göb, S., and Markl, G. 2012. Negative Ce anomalies in Mn oxides: The role of Ce4+ mobility during water-mineral interaction. Geochimica and Cosmochimica Acta 86, 296-317 Ohta A. and Kawabe I. (2001) REE (III) adsorption onto Mn dioxide (delta-MnO2) and Fe oxyhydroxide: Ce(III) oxidation by delta-MnO2. Geochim. Cosmochim. Acta 65, 695-703. Tanaka K., Tani Y., Takahashi Y., Tanimizu M., Suzuki Y., Kozai N. and Ohnuki T. (2010) A specific Ce oxidation process during sorption of rare earth elements on biogenic Mn oxide produced by Acremonium sp. strain KR21-2. Geochim. Cosmochim. Acta 74, 5463-5477.

Kinetic study of the ethene oxidation by oxygen in the presence of carbon dioxide and steam over Pt/Rh/CeO2/g-Al2O3

NARCIS (Netherlands)

Nibbelke, R.H.; Kreijveld, R.J.M.; Hoebink, J.H.B.J.; Marin, G.B.M.M.; Kruse, N.

1998-01-01

The oxidation of ethene by oxygen in the presence of steam and carbon dioxide over a commercially available Pt/Rh/CeO2/¿-Al2O3 three-way automotive catalyst was studied. Experiments were carried out in a fixed-bed micro reactor under intrinsic conditions, i.e. in the absence of external and internal

Quaternary germanides RE{sub 3}TRh{sub 4}Ge{sub 4} (RE = Ce, Pr, Nd; T = Nb, Ta) - a new coloring variant of the aristotype AlB{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, Rolf-Dieter; Vosswinkel, Daniel; Poettgen, Rainer [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster, Corrensstrasse 30, 48149 Muenster (Germany); Matar, Samir F. [CNRS, Universite de Bordeaux, ICMCB, UPR 9048, 33600 Pessac (France)

2016-09-15

The quaternary germanides RE{sub 3}TRh{sub 4}Ge{sub 4} (RE = Ce, Pr, Nd; T = Nb, Ta) were synthesized from the elements by arc-melting and subsequent annealing in a muffle furnace. The structure of Ce{sub 3}TaRh{sub 4}Ge{sub 4} was refined from single-crystal X-ray diffractometer data: new type, Pbam, a = 719.9(2), b = 1495.0(3), c = 431.61(8), wR{sub 2} = 0.0678, 1004 F{sup 2} values, and 40 variables. Isotypy of the remaining phases was evident from X-ray powder patterns. Ce{sub 3}TaRh{sub 4}Ge{sub 4} is a new superstructure variant of the aristotype AlB{sub 2} with an ordering of cerium and tantalum on the aluminum site, whereas the honey-comb network is built up by a 1:1 ordering of rhodium and germanium. This crystal-chemical relationship is discussed based on a group-subgroup scheme. The distinctly different size of tantalum and cerium leads to a pronounced puckering of the [Rh{sub 4}Ge{sub 4}] network, which shows the shortest interatomic distances (253-271 pm Rh-Ge) within the Ce{sub 3}TaRh{sub 4}Ge{sub 4} structure. Another remarkable structural feature concerns the tantalum coordination with six shorter Ta-Rh bonds (265-266 pm) and six longer Ta-Ge bonds (294-295 pm). The [Rh{sub 4}Ge{sub 4}] network fully separates the tantalum and cerium atoms (Ce-Ce > 387 pm, Ta-Ta > 431 pm, and Ce-Ta > 359 pm). The electronic density of states DOS from DFT calculations show metallic behavior with large contributions of localized Ce 4f as well as itinerant ones from all constituents at the Fermi level but no significant magnetic polarization on Ce could be identified. The bonding characteristics described based on overlap populations illustrate further the crystal chemistry observations of the different coordination of Ce1 and Ce2 in Ce{sub 3}TaRh{sub 4}Ge{sub 4}. The Rh-Ge interactions within the network are highlighted as dominant. The bonding magnitudes follow the interatomic distances and identify differences of Ta bonding vs. Ce1/Ce2 bonding with the Rh and Ge

Cube textured CeO2, BaZrO3 and LaAlO3 buffer layers on Ni based Substrates

International Nuclear Information System (INIS)

Deinhofer, C; Gritzner, G

2006-01-01

CeO 2 , BaZrO 3 as well as LaAlO 3 buffer layers were deposited on {100} Ni + 5 weight-% W substrates by a wet chemical technique. The solutions were prepared by dissolving the metal nitrates or acetates and zirconiumacetylacetonate, respectively, in mixtures of acetic acid, methanol and water. The solutions were applied by dip- or spincoating, dried at 135 deg. C and annealed at temperatures between 900 and 1 400 deg. C depending on the buffer layer for 15 min. under Ar-5% H 2 gas flow. Pole-figure measurements proved the exact texture of each buffer layer. Electron microscopy showed dense and smooth buffer layers

Catalytic oxidation of volatile organic compounds (n-hexane, benzene, toluene, o-xylene promoted by cobalt catalysts supported on γ-Al2O3-CeO2

Directory of Open Access Journals (Sweden)

R. Balzer

2014-09-01

Full Text Available Cobalt catalysts supported on γ-alumina, ceria and γ-alumina-ceria, with 10 or 20%wt of cobalt load, prepared by the wet impregnation method and characterized by X-ray diffraction (XRD, scanning electron microscopy (SEM, field emission transmission electron microscopy (FETEM, N2 adsorption-desorption isotherms (BET/BJH methods, energy-dispersive X-ray spectroscopy (EDX, X-ray photoemission spectroscopy (XPS, O2-chemisorption and temperature programmed reduction (TPR were used to promote the oxidation of volatile organic compounds (n-hexane, benzene, toluene and o-xylene. For a range of low temperatures (50-350 °C, the activity of the catalysts with a higher cobalt load (20% wt was greater than that of the catalysts with a lower cobalt load (10% wt. The Co/γ-Al2O3-CeO2 catalytic systems presented the best performances. The results obtained in the characterization suggest that the higher catalytic activity of the Co20/γ-Al2O3-CeO2 catalyst may be attributed to the higher metal content and amount of oxygen vacancies, as well as the effects of the interaction between the cobalt and the alumina and cerium oxides.

Insight on the glass-forming ability of Al–Y–Ni–Ce bulk metallic glass

Energy Technology Data Exchange (ETDEWEB)

Chen, Shih-Fan, E-mail: sfchen@ntut.edu.tw [Institute of Materials Science and Engineering, National Taipei University of Technology, Taipei 106, Taiwan (China); Chen, Chih-Yuan, E-mail: chen6563@gmail.com [Department of Energy Engineering, National United University, Miaoli 36003, Taiwan (China); Lin, Chia-Hung [Institute of Materials Science and Engineering, National Taipei University of Technology, Taipei 106, Taiwan (China)

2015-07-15

Highlights: • Adding 1 at.% cerium to Al{sub 87}Y{sub 8}Ni{sub 5} alloy causes glass transition. • A large ΔT{sub x} indicates that (Al{sub 87}Y{sub 8}Ni{sub 5}){sub 99}Ce{sub 1} is possibly a ductile amorphous alloy. • Ce is effective in improving the thermal stability of the Al–Y–Ni amorphous alloy. • The hardness of the crystallized cerium-bearing alloy was as high as 593 Hv. - Abstract: In the present study, the role of Ce in the thermal stability and glass forming ability (GFA) of (Al{sub 87}Y{sub 8}Ni{sub 5}){sub 99}Ce{sub 1} alloy ribbons produced by a single roller melt-spinning process has been investigated in an attempt to understand the influences of multiple RE elements in an Al–TM–RE (TM: transition metal, RE: rear earth metal) alloy system. Only the (Al{sub 87}Y{sub 8}Ni{sub 5}){sub 99}Ce{sub 1} alloy ribbon showed a glass transition temperature (T{sub g}) at 483.2 K, and its ΔT{sub x} value was 41.3 K. Crystallization occurred in the temperature range of 500–750 K in three exothermic reaction stages. The peak temperature for these reactions shifted toward higher temperatures at higher heating rates. XRD and SEM analysis of annealed samples revealed that nano-sized Al particles precipitated within the amorphous matrix during the first exothermic reaction. The maximum hardness was obtained for both non-cerium and cerium addition alloys after crystallization in the 550–660 K region due to numerous nano-sized precipitates randomly and homogeneously distributed in the amorphous matrix. Moreover, from observation of the fracture surface, it is found that the fracture mode transforms from ductile to brittle when the sample is annealed at a higher crystallization temperature, at which brittle intermetallic compounds appear.

Study on Microstructure and Mechanical Properties of Al-Li Based Alloys Processed by Extrusion.

Science.gov (United States)

Kim, Yong-Ho; Yoo, Hyo-Sang; Jung, Chang-Gi; Son, Hyeon-Taek

2018-03-01

Aluminum and its alloys, due to their low density, high specific strength and high corrosion resistance amongst various structural materials, are used in a wide range of industrial applications for different aqueous solutions. In the present study, we studied effects of Ce addition on microstructure and mechanical properties of Al-2Li-1Cu-0.8Mg-0.1Zr alloys. The melt was held at 780 °C for 20 min and poured into a mold. And as-cast Al alloys were hot-extruded into a plate that was 4 mm in thickness with a reduction ratio of 14:1. The extruded plates were held at 540 °C for 4 hr in water quenching to solution treatment them. As-extruded Al-2Li-1Cu-0.8Mg-0.1Zr-xCe (x = 0.3, 0.6, 0.9 and 1.2 wt.%) alloys are composed of Al, AlLi, AlCuLi and Al11Ce3 phases. By increasing the Ce content from 0 to 1.2 wt.%, the Al11Ce3 phase is increased, after solution treatment the AlLi and AlCuLi phases are decreased. With increasing Ce addition from 0 to 1.2 wt.%, the average grain size of the as-extruded Al alloys were decreased slightly from 100.7, 113.74, 84.3, 74.7 and 61.7 μm and ultimate tensile strength was decreased slightly from 267.59, 264.92, 237.40, 220.93 and 207.83 MPa at room temperature. After solution treatment, ultimate tensile strength was measured with 205.13, 198.12, 195.50, 198.27 and 208.01 MPa at room temperature.

Optimization Of Process Parameters For The Production Of Bio diesel From Waste Cooking Oil In The Presence Of Bifunctional γ-Al2O3-CeO2 Supported Catalysts

International Nuclear Information System (INIS)

Anita Ramli; Muhammad Farooq

2015-01-01

Huge quantities of waste cooking oils are produced all over the world every day, especially in the developed countries with 0.5 million ton per year waste cooking oil are being generated in Malaysia alone. Such large amount of waste cooking oil production can create disposal problems and contamination to water and land resources if not disposed properly. The use of waste cooking oil as feedstock for bio diesel production will not only avoid the competition of the same oil resources for food and fuel but will also overcome the waste cooking oil disposal problems. However, waste cooking oil has high acid value, thus would require the oil to undergo esterification with an acid catalyst prior to transesterification with a base catalyst. Therefore, in this study, bifunctional catalyst supports were developed for one-step esterification-transesterification of waste cooking oil by varying the CeO 2 loading on γ-Al 2 O 3 . The bifunctional supports were then impregnated with 5 wt % Mo and characterized using N 2 adsorption-desorption isotherm to determine the surface area of the catalysts while temperature programmed desorption with NH 3 and CO 2 as adsorbents were used to determine the acidity and basicity of the catalysts. Results show that the γ-Al 2 O 3 -CeO 2 supported Mo catalysts are active for the one-step esterification-transesterification of waste cooking oil to produce bio diesel with the Mo/ γ-Al 2 O 3 -20 wt% CeO 2 as the most active catalyst. Optimization of process parameters for the production of bio diesel from waste cooking oil in the presence of this catalyst show that 81.1 % bio diesel yield was produced at 110 degree Celsius with catalyst loading of 7 wt %, agitation speed of 600 rpm, methanol to oil ratio of 30:1 and reaction period of 270 minutes. (author)

Viscosity of Industrially Important Zn-Al Alloys Part II: Alloys with Higher Contents of Al and Si

Science.gov (United States)

Nunes, V. M. B.; Queirós, C. S. G. P.; Lourenço, M. J. V.; Santos, F. J. V.; Nieto de Castro, C. A.

2018-05-01

The viscosity of Zn-Al alloys melts, with industrial interest, was measured for temperatures between 693 K and 915 K, with an oscillating cup viscometer, and estimated expanded uncertainties between 3 and 5 %, depending on the alloy. The influence of minor components, such as Si, Mg and Ce + La, on the viscosity of the alloys is discussed. An increase in the amount of Mg triggers complex melt/solidification processes while the addition of Ce and La renders alloys viscosity almost temperature independent. Furthermore, increases in Al and Si contents decrease melts viscosity and lead to an Arrhenius type behavior. This paper complements a previous study describing the viscosity of Zn-Al alloys with quasi-eutectic compositions.

Magnetic behaviour of cerium in Ce2 Sn5 and Ce3 Sn7, surstructures of Ce Sn3

International Nuclear Information System (INIS)

Stunault, A.

1988-07-01

The compound studied, Ce 2 Sn 5 and Ce 3 Sn 7 are both orthorhombic, surstructure of cubic Ce Sn 3 . Magnetic susceptibility measurements show in both compounds an antiferromagnetic order at low temperature and magnetization shows a high anisotropy. Magnetization densities are determined by polarized neutron diffraction. The cerium site which has two Ce atoms as nearest neighbourgs carries all the magnetism in both structures. For Ce 2 Sn 5 moments are directed as the high magnetization axis and structure is modulated. Ce 3 Sn 7 presents a simple antiferromagnetic order but moment are directed as low magnetization axis. Various transitions towards a ferromagnetic order are presented. Results are interpreted by measuring the difference between energy levels of crystalline field. A model of crystalline field and isotrope exchange agrees well with Ce 3 Sn 7 , but for Ce 2 Sn 7 it is necessary to reduce the magnetic moment which is typical of the Kondo effect [fr

CeCo5 thin films with perpendicular anisotropy grown by molecular beam epitaxy

Science.gov (United States)

Sharma, S.; Hildebrandt, E.; Major, M.; Komissinskiy, P.; Radulov, I.; Alff, L.

2018-04-01

Buffer-free, highly textured (0 0 1) oriented CeCo5 thin films showing perpendicular magnetic anisotropy were synthesized on (0 0 1) Al2O3 substrates by molecular beam epitaxy. Ce exists in a mixture of Ce3+ and Ce4+ valence states as shown by X-ray photoelectron spectroscopy. The first anisotropy constant, K1, as measured by torque magnetometry was 0.82 MJ/m3 (8.2 ×106erg /cm3) . A maximum coercivity of 5.16 kOe with a negative temperature coefficient of -0.304%K-1 and a magnetization of 527.30 emu/cm3 was measured perpendicular to the film plane at 5 K. In addition, a large anisotropy of the magnetic moment of 15.5% was observed. These magnetic parameters make CeCo5 a potential candidate material for spintronic and magnetic recording applications.

Did Ibn Sina Observe the Transit of Venus of 1032 CE?

Science.gov (United States)

Kapoor, R. C.

2012-09-01

The Persian polymath Abu Ali ibn Sina (980--1037 CE), known to early Western sources as Avicenna, records that ``I say that I saw Venus as a spot on the surface of the sun''. This statement has been quoted, for example, by Nasir al Din al Tusi (1201--1274 CE). A Transit of Venus indeed took place during ibn Sina's life time, that is on 24 May 1032 CE. Did ibn Sina see this Transit or did he merely see a sunspot? The question was addressed by Bernard R. Goldstein in 1969 who concluded that ``this Transit may not have been visible where he lived''. Goldstein based his conclusion on the input provided by Brian G Marsden who in turn used mathematical tables prepared by J. Meeus in 1958. I have begun re-examination of the question by employing Fred Espenak's Transit predictions. Preliminary work shows that ibn Sina could indeed have obtained a glimpse of the Transit of Venus just before sunset from places like Isfahan or Hamadan. In other words, when ibn Sina said he saw Venus on the surface of the Sun, he probably meant it.

Linear energy transfer effects on time profiles of scintillation of Ce-doped LiCaAlF6 crystals

International Nuclear Information System (INIS)

Yanagida, Takayuki; Koshimizu, Masanori; Kurashima, Satoshi; Iwamatsu, Kazuhiro; Kimura, Atsushi; Taguchi, Mitsumasa; Fujimoto, Yutaka; Asai, Keisuke

2015-01-01

We measured temporal profiles of the scintillation of Ce-doped LiCaAlF 6 scintillator crystals at different linear energy transfers (LETs). Based on the comparison of high-LET temporal profiles with those at low LET, a fast component was observed only at low LET. The disappearance of the fast component at high LET is tentatively ascribed to the quenching of excited states at crystal defects owing to the interaction between excited states via the Auger process. In addition, the rise and the initial decay behavior were dependent on the LET. This LET-dependent behavior is explained by an acceleration process and a deceleration process in energy transfer at high LET. The LET-dependent temporal profiles provide the basis for a discrimination technique of gamma-ray and neutron detection events using these scintillators based on the nuclear reaction, 6 Li(n,α)t.

Luminescence and defects creation in Ce3+-doped YAlO3 and Lu0.3Y0.7AlO3 crystals

International Nuclear Information System (INIS)

Blazek, K.; Nejezchleb, K.; Krasnikov, A.; Savikhina, T.; Zazubovich, S.; Nikl, M.

2005-01-01

Luminescence, energy transfer and defects creation processes were studied for the Ce 3+ -doped YAlO 3 and Lu x Y 1-x AlO 3 (x=0.3) crystals in the temperature range 4.2-300 K under selective photoexcitation in the energy range 3.5-11.5 eV. For the first time, defects creation spectra were measured and analyzed. Influence of the charge and ionic radii of co-doping ions on the luminescence and defects creation efficiency was considered. The origin of the defects created and possible mechanisms of their formation were discussed. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

El Conde Casio, los Banu Qasi y los linajes godos en Al-Andalus

Directory of Open Access Journals (Sweden)

Maribel FIERRO

2011-02-01

Full Text Available Este texto es una relectura de los orígenes de la familia Banu Qasi, a partir de las conclusiones de la reciente tesis de Jesús Lorenzo Jiménez. De acuerdo con ese trabajo, se descarta la condición de importante personaje aristocrático del epónimo Casio. Se observa además un proceso de formación de una memoria genealógica, vinculada a los Omeyas, que surgió al calor del reforzamiento ideológico del poder de los emires cordobeses.

Effects of Ce and Zr addition on microstructure and hardness of Al-Si-Cu-Mg alloy

International Nuclear Information System (INIS)

Bevilaqua, William Lemos; Reguly, Afonso; Froehlich, Andre Ronaldo; Stadtlander, Antonio Ricardo

2016-01-01

The effects of cerium and zirconium contents (0.3%-0.16%Zr; 0.3%-0.27%Zr e 0.3%-0.36%Zr) to aluminum alloy 354.0 was investigated by microstructural analysis and hardness measurements in as-cast and heat-treated conditions. The macrostructure show an excellent grain refinement for all Ce and Zr contents used. Additionally, the Cu-Ce reaction during solidification changes significantly the age hardening process of modified alloys. (author)

CE and nanomaterials - Part II: Nanomaterials in CE.

Science.gov (United States)

Adam, Vojtech; Vaculovicova, Marketa

2017-10-01

The scope of this two-part review is to summarize publications dealing with CE and nanomaterials together. This topic can be viewed from two broad perspectives, and this article is trying to highlight these two approaches: (i) CE of nanomaterials, and (ii) nanomaterials in CE. The second part aims at summarization of publications dealing with application of nanomaterials for enhancement of CE performance either in terms of increasing the separation resolution or for improvement of the detection. To increase the resolution, nanomaterials are employed as either surface modification of the capillary wall forming open tubular column or as additives to the separation electrolyte resulting in a pseudostationary phase. Moreover, nanomaterials have proven to be very beneficial for increasing also the sensitivity of detection employed in CE or even they enable the detection (e.g., fluorescent tags of nonfluorescent molecules). © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Data and analyses of phase relations in the Ce-Fe-Sb ternary system.

Science.gov (United States)

Zhu, Daiman; Xu, Chengliang; Li, Changrong; Guo, Cuiping; Zheng, Raowen; Du, Zhenmin; Li, Junqin

2018-02-01

These data and analyses support the research article "Experimental study on phase relations in the Ce-Fe-Sb ternary system" Zhu et al. (2017) [1]. The data and analyses presented here include the experimental results of XRD, SEM and EPMA for the determination of the whole liquidus projection and the isothermal section at 823 K in the Ce-Fe-Sb system. All the results enable the understanding of the constituent phases and the solidification processes of the as-cast alloys as well as the phase relations and the equilibrium regions at 823 K in the Ce-Fe-Sb ternary system over the entire composition.

First principles electronic and thermal properties of some AlRE intermetallics

Science.gov (United States)

Srivastava, Vipul; Sanyal, Sankar P.; Rajagopalan, M.

2008-10-01

A study on structural and electronic properties of non-magnetic cubic B 2-type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grüneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grüneisen model and compared with the others’ theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics.

First principles electronic and thermal properties of some AlRE intermetallics

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Vipul [Department of Physics, Barkatullah University, Hoshangabad Road, Bhopal, Madhya Pradesh 462 026 (India)], E-mail: vips73@yahoo.com; Sanyal, Sankar P. [Department of Physics, Barkatullah University, Hoshangabad Road, Bhopal, Madhya Pradesh 462 026 (India); Rajagopalan, M. [Department of Physics, Anna University, Chennai-600 025 (India)

2008-10-01

A study on structural and electronic properties of non-magnetic cubic B{sub 2}-type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grueneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grueneisen model and compared with the others' theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics.

First principles electronic and thermal properties of some AlRE intermetallics

International Nuclear Information System (INIS)

Srivastava, Vipul; Sanyal, Sankar P.; Rajagopalan, M.

2008-01-01

A study on structural and electronic properties of non-magnetic cubic B 2 -type AlRE (RE=Sc, Y, La, Ce, Pr and Lu) intermetallics has been done theoretically. The self-consistent tight binding linear muffin tin orbital method is used to describe the electronic properties of these intermetallics at ambient and at high pressure. These compounds show metallic behavior under ambient conditions. The variation of density of states under compression indicates some possibility of structural phase transformation in AlLa, AlCe and AlPr. Thermal properties like Debye temperature and Grueneisen constant are calculated at T=0 K and at ambient pressure within the Debye-Grueneisen model and compared with the others' theoretical results. Our results are in good agreement. We have also performed a pressure-induced variation of Debye temperature and have found a decrease in Debye temperature around 40 kbar in AlRE (RE=La, Ce, Pr) intermetallics

Dynamical magnetic response of paramagnetic CeFe-2

International Nuclear Information System (INIS)

Rainford, B.D.; McK Paul, D.; Warwick Univ., Coventry

1988-01-01

Inelastic neutron scattering has been used to study the energy dependence of the paramagnetic response from CeFe 2 . Our results, when integrated over energy, are in excellent agreement with the polarised neutron experiments of Deportes et al., but the correlation length obtained by fitting the data to a double Lorentzian scattering function is significantly smaller than that derived previously

Magnetoresistance in CePtSn under high hydrostatic pressures

International Nuclear Information System (INIS)

Misek, M.; Prokleska, J.; Javorsky, P.; Sechovsky, V.

2009-01-01

We report the evolution of magnetic-history dependent antiferromagnetic phases in CePtSn. We concentrate on the magnetoresistance in magnetic fields up to 14 T applied along the crystallographic b-axis, measured on a CePtSn single crystal subjected to hydrostatic pressure (p ≤ 2.2 GPa) generated in a double-layered CuBe/NiCrAl piston cylinder cell. We observe a gradual increase of the critical field B c LF of the low field (LF) transition up to ∼1.2 GPa where only one transition is observed at ∼11.5 T. For pressures above 1.2 GPa we observe two transitions again and B c LF decreases with further increasing pressure to reach B c LF ∼7.5T at 2.5 GPa. The position of the high field (HF) transition remains almost unaffected by applied pressure. A scenario considering the spin-slip AF structure in CePtSn is briefly discussed.

Structure and properties of the Mn doped CeO{sub 2} thin film grown on LaAlO{sub 3} (0 0 1) via a modified sol–gel spin-coating technique

Energy Technology Data Exchange (ETDEWEB)

Mahmoud, Waleed E., E-mail: w_e_mahmoud@yahoo.com [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Suez Canal University, Faculty of Science, Department of Physics, Ismailia (Egypt); Al-Ghamdi, A.A. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Al-Agel, F.A. [Hail University, College of Science, Department of Physics, Hail (Saudi Arabia); Al-Arfaj, E. [Umm Alqura University, Department of Physics, Makkah (Saudi Arabia); Qaseem University, Physics Department, Qaseem (Saudi Arabia); Shokr, F.S. [King Abdulaziz University, Faculty of Science & Arts, Department of Physics, Rabigh (Saudi Arabia); Al-Gahtany, S.A. [King Abdulaziz University, Faculty of Science for Girls, Department of Physics, Jeddah (Saudi Arabia); Alshahrie, Ahmed [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Hafez, M. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Suez Canal University, Faculty of Science, Department of Physics, Ismailia (Egypt); Bronstein, L.M. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Indiana University, Department of Chemistry, Bloomington, IN 47405 (United States); Beall, Gary W. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Texas State University-San Marcos, Department of Chemistry and Biochemistry, 601 University Dr., San Marcos, TX 78666 (United States)

2015-08-15

Highlights: • Mn doped CeO{sub 2} was grown on LaAlO{sub 3} (0 0 1) via sol–gel technique. • The concentration of the Mn ions was varied from 1 to 13 at.%. • The incorporation of 7 at.% of Mn ions was found to provide formation of exceptionally smooth films. • This amount demonstrated the highest saturation magnetization of 1.75 μ{sub B}/Mn and coercive field of 487 Gauss. - Abstract: Here we report Mn doped cerium oxide films prepared on the LaAlO{sub 3} (0 0 1) substrate via an ethylene glycol modified sol–gel spin coating technique and evaluation of their properties as diluted magnetic semiconductors. Cerium oxide was selected because of its high dielectric constant and fluorite cubic structure, matching the silicon and lanthanum aluminate based electronic devices. The concentration of the Mn ions was varied from 1 to 13 at.% and the influence of this concentration on the structure, surface morphology, optical and magnetic properties of these films was studied using scanning electron microscopy, energy dispersive spectroscopy, atomic force microscopy, ellipsometric spectroscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, and magnetic measurements. The incorporation of 7 at.% of Mn ions was found to provide formation of exceptionally smooth films, demonstrating the highest saturation magnetization of 1.75 μ{sub B}/Mn and the coercive field of 487 Gauss. These properties are assigned to the conversion of Ce{sup 4+} to Ce{sup 3+} upon incorporation of Mn ions into the CeO{sub 2} structure and the oxidation of Mn{sup 2+} to Mn{sup 4+}, creating two oxygen vacancies to preserve the cubic structure of cerium oxide and promoting ferromagnetism.

Pyrazolates advance cerium chemistry: a CeIII/CeIV redox equilibrium with benzoquinone.

Science.gov (United States)

Werner, Daniel; Deacon, Glen B; Junk, Peter C; Anwander, Reiner

2017-05-16

Two stable cerium(iv) 3,5-dialkylpyrazolate complexes are presented, namely dimeric [Ce(Me 2 pz) 4 ] 2 (Me 2 pz = 3,5-dimethylpyrazolate) and monomeric Ce(tBu 2 pz) 4 (tBu 2 pz = 3,5-di-tert-butylpyrazolate) along with their trivalent counterparts [Ce(Me 2 pz) 3 ] and [Ce(tBu 2 pz) 3 ] 2 . All complexes were obtained from protonolysis reactions employing the silylamide precursors Ce[N(SiHMe 2 ) 2 ] 4 and Ce[N(SiMe 3 ) 2 ] 3 . Treatment of homoleptic Ce IV and Ce III Me 2 pz complexes with 1,4-hydroquinone (H 2 hq) or 1,4-benzoquinone (bq), respectively, ultimately gave the same trimetallic Ce III species via a cerium redox equilibrium. The Ce III complex Ce 3 (Me 2 pz) 5 (pchd) 2 (L) (pchd = 1,4-bis(3,5-dimethylpyrazol-1-yl)cyclohex-2,5-diene-1,4-diolato; L = Me 2 pzH or (thf) 2 ) results from a di-1,4-pyrazolyl attack on pre-coordinated bq. The reduction of bq by [Ce(Me 2 pz) 3 (thf)] 2 , and re-oxidation by the resulting Ce IV species was supported by UV-vis spectroscopic investigations. Comparisons with the redox-innocent complexes [Ln(Me 2 pz) 3 (thf)] 2 (Ln = La and Pr) revealed far less selective reactions with bq, giving hexametallic and octametallic rare-earth metal side products containing 2-Me 2 pz substituted hq ligands.

EPR study of concentration dependence in Ce, Ce : La and Ce:Y doped SrF2

NARCIS (Netherlands)

Dankert, O.; Vainchtein, David; Datema, H.C.; den Hartog, Hendrik

1995-01-01

Experimental results of an EPR-study of the concentration dependence of the doubly integrated intensity and linewidth of the signals associated with tetragonal Ce3+-F--dipoles in Sr1-xCexF2+x, Sr-1-0.005-x Ce0.005LaxF2+0.005+x and Sr-1-0.005-x Ce0.005YxF2+0.005+x are presented. Both show a nonlinear

Studies on the agronomy of Al-Andalus

Directory of Open Access Journals (Sweden)

Julia María Carabaza

2014-07-01

Full Text Available Comme il peut être déduit du titre donné à ce travail, le principal objectif que nous nous sommes fixées, c'est de procéder à une mise à jour de la recherche en ce qui concerne les œuvres agricoles écrites à Al-Andalus. Pour ce faire, nous analyserons dans un premier temps, les manuscrits que l'on connaît de ces œuvres en question et qui appartiennent aussi bien aux bibliothèques du monde arabe qu’à des bibliothèques occidentales. Ensuite, nous mentionnerons les traités agronomiques qui sont actuellement édités et traduits, accompagnés de quelques notes critiques concernant les travaux qui ont été mis en œuvre jusqu'à présent dans ce domaine, pour terminer avec l'exposé des différents projets qui sont actuellement en cours et qui sont relatifs à ces traités agricoles d’Al-Andalus.

Recent approaches for enhancing sensitivity in enantioseparations by CE.

Science.gov (United States)

Sánchez-Hernández, Laura; García-Ruiz, Carmen; Luisa Marina, María; Luis Crego, Antonio

2010-01-01

This article reviews the latest methodological and instrumental improvements for enhancing sensitivity in chiral analysis by CE. The review covers literature from March 2007 until May 2009, that is, the works published after the appearance of the latest review article on the same topic by Sánchez-Hernández et al. [Electrophoresis 2008, 29, 237-251]. Off-line and on-line sample treatment techniques, on-line sample preconcentration strategies based on electrophoretic and chromatographic principles, and alternative detection systems to the widely employed UV/Vis detection in CE are the most relevant approaches discussed for improving sensitivity. Microchip technologies are also included since they can open up great possibilities to achieve sensitive and fast enantiomeric separations.

Coherence Kondo gap in CeNiSn and CeRhSb

International Nuclear Information System (INIS)

Takabatake, T.; Nakamoto, G.; Tanaka, H.; Bando, Y.; Fujii, H.; Nishigori, S.; Goshima, H.; Suzuki, T.; Fujita, T.; Oguro, I.; Hiraoka, T.; Malik, S.K.

1994-01-01

CeNiSn and CeRhSb are Kondo-lattice compounds showing the behavior of a small-gap semiconductor at temperatures below 7 K. We review and discuss the magnetic, transport and specific-heat measurements performed on single crystals of CeNiSn and polycrystals of CeRhSb. Prerequisites for gap formation are deduced from the effects of substitution and application of a magnetic field and pressure on the gapped state. ((orig.))

Effect of Preparation Methods on Al2O3 Supported CuO-CeO2-ZrO2 Catalysts for CO Oxidation

Directory of Open Access Journals (Sweden)

Gaurav Rattan

2012-12-01

Full Text Available To examine the effect of preparation methods, four catalyst samples having same composition (CuCe5.17Zr3.83Ox/g-Al2O3 (15wt% were prepared by four different methods for CO oxidation. The catalysts were prepared by co-impregnation, citric acid sol-gel, urea nitrate combustion and urea gelation co-precipitation methods, and characterized by BET, XRD, TGA/DSC and SEM. The The air oxidation of CO was carried out in a tubular fixed bed reactor under the following operating conditions: catalyst weight - 100 mg, temperature - ambient to 250 oC, pressure - atmospheric, 2.5% CO in air, total feed rate - 60 ml/min.  It was observed that the catalytic activity greatly influenced by the preparation methods. The highest activity of the catalyst prepared by the sol gel method appeared to be associated with its largest BET surface area. All the four catalysts were active for CO oxidation and did not show deactivation of catalytic activity for 50 hours of continuous runs. The ranking order of the preparation methods of the catalyst is as follows: sol-gel > co-impregnation > urea gelation > urea nitrate combustion. Copyright © 2012 by BCREC UNDIP. All rights reservedReceived: 14th June 2012, Revised: 8th September 2012, Accepted: 19th September 2012[How to Cite: G. Rattan, R. Prasad, R.C.Katyal. (2012. Effect of Preparation Methods on Al2O3 Supported CuO-CeO2-ZrO2 Catalysts for CO Oxidation. Bulletin of Chemical Reaction Engineering & Catalysis, 7(2: 112-123. doi:10.9767/bcrec.7.2.3646.112-123] [How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.3646.112-123 ] | View in 

Influence of the sintering temperature on the Sr content in a Ca{sub (1−x−y)}Ce{sub x}Sr{sub y}Al{sub z}Ti{sub (1−z)}O{sub 3} perovskite (x = 0.04–0.16) co-doped with Ce

Energy Technology Data Exchange (ETDEWEB)

Kamel, Nour-el-hayet; Mouheb, Yasmina, E-mail: mouhebyascrna@hotmail.com; Kamel, Ziane; Moudir, Dalila; Aouchiche, Fairouz; Arabi, Azeddine

2016-08-15

A Sr-Ce co-doped perovskite, with the chemical formula: Ca{sub (1−x−y)}Ce{sub x}Sr{sub y}Al{sub z}Ti{sub (1−z)}O{sub 3} (y = 0.04, 0.08, 0.12 and 0.16, x = 0.05) is synthesized by sol–gel process. The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. The Sr amount sequestered in the perovskite reaches 85% (y = 0.16, 9.50 wt%) for Ts = 1373 K, giving sintering densities between 3.520 and 4.400. XRD analysis reveals an orthorhombic CaTiO{sub 3} structure. The lattice parameters obey to Vegard’s law for Ts = 1373 and 1473 K. SEM analysis shows orthorhombic grains of 0.514 μm × 1 μm mean dimensions. MCC1 and MCC2 tests, performed on minerals sintered at 1373 K, indicate that the most durable one is that containing 9.50 wt% Sr. MCC1 test gave 6.998·10{sup −6} g/cm{sup 2} d of Sr, and MCC2 2.143·10{sup −4} g/cm{sup 2} d of Ce. The temperature favors the Sr dissolution to the detriment of Ce. The Ca dissolution rate reaches 1.002·10{sup −6} to 2.005·10{sup −6} g/cm{sup 2} d. - Highlights: • Ca{sub (1−x−y)}Ce{sub x}Sr{sub y}Al{sub z}Ti{sub (1−z)}O{sub 3} perovskite is synthesized by sol–gel. • The influence of the sintering temperature, Ts, on the rate of inserted Sr was investigated at 1223, 1373 and 1473 K. • 85% of total Sr was sequestered in the perovskite for Ts = 1373 K. • MCC1 and MCC2 leach tests indicate that the most durable mineral is that containing 9.50 wt.% Sr. • MCC1 test gave 8.10 10{sup −10} kg/m{sup 2}.d Sr. The lower is the leaching temperature the higher is the mineral durability.

Production and characterization of monocrystals of the cubic Laves phases Se-Al2

International Nuclear Information System (INIS)

Beyss, M.; Uelhoff, W.; Fattah, A.

1977-04-01

The monocrystals of the cubic Laves phases Se-Al 2 have been produced for special measurements. Low-temperature anomalies were measured which were influenced by doping with foreign atoms. These anomalies, also called Kondo effect, were detected in some physical quantities like electric resistance, magnetic resistance, susceptibility, magnetization, specific heat, thermal conductivity and thermoelectric force. For diffuse magnetic neutron scattering, monocrystals with the dimensions 10 mm diameter and 70 mm length were produced. The materials used were La Al 2 , (La Ce) Al 2 , Ce Al 2 , Y Al 2 , and (Y Ce) Al 2 . The monocrystals had to have an exactly cylindrical cross-section which was obtained by stripping by means of spark erosion machines. The measurements were carried out at the reactor of the Laue-Langevin Institute at Grenoble. In the experiments the magnetic behavior was measured by neutron scattering on monocrystals in the temperature range from 2.5 K to 300 K, the energy spectra having been registered. (orig.) [de

Mathematical instrumentation in fourteenth-century Egypt and Syria the illustrated treatise of Najm al-Din al-Misri

CERN Document Server

Charette, F

2003-01-01

An illustrated Arabic treatise, with an English translation and detailed commentary, on the construction of over 100 various astronomical instruments, many of which are otherwise unknown to specialists. It was composed by Najm al-Din al-Misri, a rather shadowy figure, in Cairo around 1330 CE.

Retos de la Universidad de Guantánamo en el proceso de innovación social conectado al desarrollo local

Directory of Open Access Journals (Sweden)

Rolando Durand-Rill

2017-04-01

Full Text Available Se sistematiza la experiencia de la Universidad de Guantánamo (UG como interfase innovadora e integrada al desarrollo local, se argumenta la necesidad de fortalecer el empoderamiento ciudadano en la toma de decisiones ante los complejos retos actuales para la solución creativa de problemas, y se proponen acciones en el tratamiento de la innovación social, vinculadas con las líneas de investigación universitaria.

Structural, magnetic and optical properties of a dilute magnetic semiconductor based on Ce{sub 1−x}Co{sub x}O{sub 2} thin film grown on LaAlO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Mahmoud, Waleed E., E-mail: w_e_mahmoud@yahoo.com [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Suez Canal University, Faculty of Science, Department of Physics, Ismailia (Egypt); Al-Ghamdi, A.A. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Al-Agel, F.A. [Hail University, College of Science, Department of Physics, Hail (Saudi Arabia); Al-Arfaj, E. [Umm Alqura University, Department of Physics, Makkah (Saudi Arabia); Qassim University, College of Science, Physics Department, Buraidah 5145 (Saudi Arabia); Shokr, F.S. [King Abdulaziz University, Faculty of Science & Arts, Department of Physics, Rabigh (Saudi Arabia); Al-Gahtany, S.A. [King Abdulaziz University, Faculty of Science for Girls, Department of Physics, Jeddah (Saudi Arabia); Alshahrie, Ahmed [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Jalled, Ouissem [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Laboratory of Applied Mineral Chemistry, Department of Chemistry, University Tunis ElManar, Faculty of Sciences, Campus 2092, Tunis (Tunisia); Bronstein, L.M. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Texas State University-San Marcos, Department of Chemistry and Biochemistry, 601 University Dr., San Marcos, TX 78666 (United States); Beall, Gary W. [King Abdulaziz University, Faculty of Science, Department of Physics, Jeddah (Saudi Arabia); Indiana University, Department of Chemistry, Bloomington, IN 47405 (United States)

2015-12-15

Highlights: • Co doped CeO{sub 2} was grown on LaAlO{sub 3} (0 0 1) via a modified sol–gel spin-coating technique. • The concentration of the Co ions was varied from 1 to 15 at.%. • The incorporation of 5 at.% of Mn ions was found to provide formation of exceptionally magnetic moment. • This amount demonstrated a giant magnetic moment of 1.09 μ{sub B}/Co. • This amount reduced the optical band gap and enhanced the optical performance. - Abstract: The enhancement of the room temperature ferromagnetism and optical properties of the dilute magnetic metal oxides is a crucial clue to construct spin-based optoelectronic devices. In this work, Ce{sub 1−x}Co{sub x}O{sub 2} (0.01 ≤ x ≤0.15) thin films were prepared via ethylene glycol modified sol–gel spin coating technique on the LaAlO{sub 3} (0 0 1) substrate to enhance their room temperature ferromagnetism and optical properties. The structures, magnetic and optical properties of the prepared films were characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, SQUID magnetometer, X-ray photoelectron spectroscopy and UV–vis spectrophotometer. The results demonstrated that a single phase cubic structure was formed, implying the substitution of Co ions into the Ce ions sites. The prepared films showed room temperature ferromagnetism with saturation magnetic moment of 1.09 μ{sub B}/Co was achieved for 5 at.% Co-doped CeO{sub 2}. This film exhibited high optical transparency of 85% and low optical band energy gap of 3.39 eV. The improved magnetic and optical properties are argued to the increase of the density of the oxygen vacancies into the cerium oxide crystal structure due to the incorporation of Co ions.

Microstructural characterisation of Al-Si cast alloys containing rare earth additions

Science.gov (United States)

Elgallad, E. M.; Ibrahim, M. F.; Doty, H. W.; Samuel, F. H.

2018-05-01

This paper presents a thorough study on the effect of rare earth elements, specifically La and Ce, on the microstructure characteristics of non-modified and Sr-modified A356 and A413 alloys. Several alloys were prepared by adding 1% La and 1% Ce either individually or in combination. Microstructural characterisation was carried out using optical microscopy, scanning electron microscopy and electron probe microanalysis as well as differential scanning calorimetry (DSC) analysis. The results showed that the individual and combined additions of La and Ce did not bring about any modification or even refinement in the eutectic Si structure. Moreover, these additions were found to negate the modification effect of Sr, particularly in the presence of La. The A356 and A413 alloys containing La and/or Ce displayed high phase volume fractions owing to the formation of Al-Si-La/Ce/(La,Ce) and Al-Ti-La/Ce intermetallic phases. DSC analysis revealed that the formation temperatures of these phases varied from 560 to 568 °C and 568 to 574 °C, respectively. This analysis also showed that the addition of La and Ce whether individually or in combination resulted in a depression in the eutectic temperature and a considerable increase in the solidification range, particularly for the A413 alloy.

Influence of Ce-H bonding on the physical properties of the hydrides CeCoSiH1.0 and CeCoGeH1.0

International Nuclear Information System (INIS)

Chevalier, B; Matar, S F; Menetrier, M; Marcos, J Sanchez; Fernandez, J Rodriguez

2006-01-01

The hydrides CeCoSiH 1.0 and CeCoGeH 1.0 which crystallize like the parent antiferromagnetic compounds CeCoSi and CeCoGe in the tetragonal CeFeSi-type structure, have been investigated by specific heat and thermoelectric power measurements and 1 H nuclear magnetic resonance (NMR). CeCoSiH 1.0 is an intermediate valence compound whereas CeCoGeH 1.0 can be considered as a nearly trivalent cerium compound. This behaviour is corroborated by the occurrence of a slight broadening of the 1 H NMR signal in the sequence CeCoSiH 1.0 → CeCoGeH 1.0 . The band structure calculations performed on these hydrides reveal the existence of strong bonding Ce-H interaction, found to be larger in CeCoSiH 1.0 than in CeCoGeH 1.0

Linear energy transfer effects on time profiles of scintillation of Ce-doped LiCaAlF{sub 6} crystals

Energy Technology Data Exchange (ETDEWEB)

Yanagida, Takayuki [Graduate School of Materials Science, Nara Institute of Science and Technology, 8916-5 Takayama-Cho, Ikoma, Nara 630-0192 (Japan); Koshimizu, Masanori [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan); Kurashima, Satoshi [Takasaki Advanced Radiation Research Institute, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Iwamatsu, Kazuhiro [Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Tokyo 113-8656 (Japan); Kimura, Atsushi; Taguchi, Mitsumasa [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Fujimoto, Yutaka; Asai, Keisuke [Department of Applied Chemistry, Graduate School of Engineering, Tohoku University, 6-6-07 Aoba, Aramaki, Aoba-ku, Sendai 980-8579 (Japan)

2015-12-15

We measured temporal profiles of the scintillation of Ce-doped LiCaAlF{sub 6} scintillator crystals at different linear energy transfers (LETs). Based on the comparison of high-LET temporal profiles with those at low LET, a fast component was observed only at low LET. The disappearance of the fast component at high LET is tentatively ascribed to the quenching of excited states at crystal defects owing to the interaction between excited states via the Auger process. In addition, the rise and the initial decay behavior were dependent on the LET. This LET-dependent behavior is explained by an acceleration process and a deceleration process in energy transfer at high LET. The LET-dependent temporal profiles provide the basis for a discrimination technique of gamma-ray and neutron detection events using these scintillators based on the nuclear reaction, {sup 6}Li(n,α)t.

Low cycle fatigue behavior of polycrystalline NiAl at 300 and 1000 K

Science.gov (United States)

Lerch, Bradley A.; Noebe, Ronald D.

1993-01-01

The low cycle fatigue behavior of polycrystalline NiAl was determined at 300 and 1000 K - temperatures below and above the brittle- to-ductile transition temperature (BDTT). Fully reversed, plastic strain-controlled fatigue tests were conducted on two differently fabricated alloy samples: hot isostatically pressed (HIP'ed) prealloyed powder and hot extruded castings. HIP'ed powder (HP) samples were tested only at 1000 K, whereas the more ductile cast-and-extruded (C+E) NiAl samples were tested at both 1000 and 300 K. Plastic strain ranges of 0.06 to 0.2 percent were used. The C+E NiAl cyclically hardened until fracture, reaching stress levels approximately 60 percent greater than the ultimate tensile strength of the alloy. Compared on a strain basis, NiAl had a much longer fatigue life than other B2 ordered compounds in which fracture initiated at processing-related defects. These defects controlled fatigue life at 300 K, with fracture occurring rapidly once a critical stress level was reached. At 1000 K, above the BDTT, both the C+E and HP samples cyclically softened during most of the fatigue tests in air and were insensitive to processing defects. The processing method did not have a major effect on fatigue life; the lives of the HP samples were about a factor of three shorter than the C+E NiAl, but this was attributed to the lower stress response of the C+E material. The C+E NiAl underwent dynamic grain growth, whereas the HP material maintained a constant grain size during testing. In both materials, fatigue life was controlled by intergranular cavitation and creep processes, which led to fatigue crack growth that was primarily intergranular in nature. Final fracture by overload was transgranular in nature. Also, HP samples tested in vacuum had a life three times longer than their counterparts tested in air and, in contrast to those tested in air, hardened continuously over half of the sample life, thereby indicating an environmentally assisted fatigue damage

Ce-doping effects on electronic structures of Ba0.5Sr0.5TiO3 thin film

International Nuclear Information System (INIS)

Wang, S Y; Cheng, B L; Wang, Can; Button, T W; Dai, S Y; Jin, K J; Lu, H B; Zhou, Y L; Chen, Z H; Yang, G Z

2006-01-01

In order to clarify the basic reason why Ce doping can dramatically decrease the leakage current in Ba 0.5 Sr 0.5 TiO 3 (BST) as reported in our previous work (Wang et al 2005 J. Phys. D: Appl. Phys. 38 2253), we have employed x-ray photoelectron spectroscopy (XPS) and the optical transmittance technique to study the electronic structure of undoped and 1.0 at% Ce-doped BST (CeBST) films fabricated by pulsed laser deposition. XPS results show that Ce doping has a strong influence on the valence band and core levels of BST films, and that the Fermi level is lowered by about 0.35 eV by Ce doping. Optical transmittance measurements demonstrate that the energy gap is expanded with Ce doping. These Ce-doping effects can induce an increase in the barrier height for the thermionic emission and eventually reduce leakage current in CeBST thin films

RFe{sub 2}Mg{sub x}Al{sub 8−x} (R=La–Nd and Sm; x≈0.8): Flux synthesis, structure, magnetic and electrical properties

Energy Technology Data Exchange (ETDEWEB)

Ma, Xiaowei; Chai, Ping; Chen, Banghao [Department of Chemistry and Biochemistry, Florida State University, Tallahassee, FL 32306 (United States); Lochner, Eric [Department of Physics, Florida State University, Tallahassee, FL 32306 (United States); Latturner, Susan E., E-mail: latturne@chem.fsu.edu [Department of Chemistry and Biochemistry, Florida State University, Tallahassee, FL 32306 (United States)

2015-09-15

Single crystals of Mg-substituted CeFe{sub 2}Al{sub 8} type intermetallics RFe{sub 2}Mg{sub x}Al{sub 8–x} (R=La–Nd and Sm; x≤1) were grown by reacting iron and rare earth metals in 1:1 Mg/Al mixed flux. The structure features mono-capped and bi-capped trigonal prismatic FeAl{sub 6} units. Electronic structure calculations indicate that magnesium substitution reduces the valence electron count, shifting the Fermi level away from a pseudo-gap. This changes the electronic nature of the cerium analog; the previously reported ternary CeFe{sub 2}Al{sub 8} shows strong hybridization between the cerium states and the conduction electrons, resulting in no magnetic moment on Ce atoms. On the other hand, magnetic susceptibility measurements on CeFe{sub 2}Mg{sub x}Al{sub 8–x} indicates a localized moment on cerium. The newly synthesized Pr, Nd and Sm analogs exhibit antiferromagnetic ordering at 2.8 K, 7.8 K and 12 K respectively. Solid state {sup 27}Al NMR of LaFe{sub 2}Mg{sub x}Al{sub 8–x} exhibits a broad Knight shift at ~1200 ppm, consistent with the metallic behavior shown by electrical resistivity data. - Graphical abstract: Mg substitution into CeFe{sub 2}Al{sub 8} modifies cerium valence due to changing valence electron count. - Highlights: • RFe{sub 2}Mg{sub x}Al{sub 8−x} (R=La–Nd, Sm) grow as large crystals from reactions in Mg/Al flux. • Products are magnesium-substituted variants of CeFe{sub 2}Al{sub 8}, with CaCo{sub 2}Al{sub 8} structure. • Ce magnetic moment in CeFe{sub 2}Mg{sub x}Al{sub 8−x} varies from that in CeFe{sub 2}Al{sub 8} due to VEC change. • Antiferromagnetic ordering observed for Pr, Nd, Sm analogs of RFe{sub 2}Mg{sub x}Al{sub 8−x}.

Monolithic Au/CeO2 nanorod framework catalyst prepared by dealloying for low-temperature CO oxidation

Science.gov (United States)

Zhang, Xiaolong; Duan, Dong; Li, Guijing; Feng, Wenjie; Yang, Sen; Sun, Zhanbo

2018-03-01

Monolithic Au/CeO2 nanorod frameworks (NFs) with porous structure were prepared by dealloying melt-spun Al89.7Ce10Au0.3 ribbons. After calcination in O2, a 3D Au/CeO2 NF catalyst with large surface area was obtained and used for low-temperature CO oxidation. The small Au clusters/nanoparticles (NPs) were in situ supported and highly dispersed on the nanorod surface, creating many nanoscale contact interfaces. XPS results demonstrated that high-concentration oxygen vacancy and Au δ+/Au0 co-existed in the calcined sample. The Au/CeO2 nanorod catalyst calcined at 400 °C exhibited much higher catalytic activity for CO oxidation compared with the dealloyed sample and bare CeO2 nanorods. Moreover, its complete reaction temperature was as low as 91 °C. The designed Au/CeO2 NF catalyst not only possessed extreme sintering resistance but also exhibited high performance owing to the enhanced interaction between the Au clusters/NPs and CeO2 nanorod during calcination.

UNA MIRADA DESDE EL GENERO AL DISCURSO DE JUECES/ZAS Y OTROS ACTORES DEL SISTEMA PROCESAL PENAL

OpenAIRE

SILVA J., PAULA; SILVA J., PAULA

2007-01-01

El presente documento tiene por finalidad presentar el trabajo de tesis para magíster, denominada "Una Mirada desde el Género al Discurso de Jueces/zas y otros Actores del Sistema Procesal Penal' E/interés por el tema en cuestión se remite a anteriores investigaciones realizadas a lo largo de tiempo, las cuales desde una perspectiva de género, han estado vinculadas con el consumo de drogas y delictualidad, criminalidad y mundo intrapenitenciario, sexualidad de las mujeres intramuros, y fin...

Synthesis of crystalline Ce-activated garnet phosphor powders and technique to characterize their scintillation light yield

Science.gov (United States)

Gordienko, E.; Fedorov, A.; Radiuk, E.; Mechinsky, V.; Dosovitskiy, G.; Vashchenkova, E.; Kuznetsova, D.; Retivov, V.; Dosovitskiy, A.; Korjik, M.; Sandu, R.

2018-04-01

This work reports on a process of preparation of garnet phosphor powders and a technique for light yield evaluation of strongly light scattering samples. Powders of scintillation compounds could be used as individual materials or as samples for express tests of scintillation properties. However, estimation of their light yield (LY) is complicated by strong light scattering of this kind of materials. Ce3+-activated yttrium-aluminum and gallium-gadolinium-aluminum garnet phosphor powders, Y3Al5O12 (YAG:Ce) and Gd3Ga3Al2O12 (GGAG:Ce), were obtained using a modified coprecipitation technique. Ga tends to residue in mother liquor in ammonia media, but the modification allows to avoid the loss of components. We propose an approach for sample preparation and LY measurement setup with alpha particles excitation, allowing to decrease light scattering influence and to estimate a light yield of powder samples. This approach is used to evaluate the obtained powders.

Characterization and Catalytic Activity for the Oxidation of Ethane and Propane on Platinum and Copper Supported on CeO2/Al2O3

Directory of Open Access Journals (Sweden)

Cataluña R.

1998-01-01

Full Text Available Ethane and propane oxidation on platinum and copper supported on Al2O3 and CeO2/Al2O3 catalysts were studied comparatively by examining reaction rates as a function of temperature. Results show that the addition of cerium oxide shifts the catalytic activity to higher temperatures. This negative influence is less pronounced in the case of supported copper samples, which on the basis of EPR and FTIR of adsorbed CO results is attributed to the low relative amount of this metal is in contact with ceria. The decrease in activity the presence of ceria might be due to changes in metal particle size or to the stabilization of the oxidized states of the metals, induced by their interactions with cerium oxide. The higher activity of platinum, in comparison with copper, is attributed to its higher reducibility along with an easier hydrocarbon activation on that metal.

Preparation of AAO-CeO2 nanotubes and their application in electrochemical oxidation desulfurization of diesel

Science.gov (United States)

Du, Xiaoqing; Yang, Yumeng; Yi, Chenxi; Chen, Yu; Cai, Chao; Zhang, Zhao

2017-02-01

The coaxial arrays of AAO-CeO2 NTs have been successfully galvanostatically deposited on an anode, characterized and adopted as a catalyst for removing organic sulfurs from diesel. The influence of the main electrochemical oxidation factors on the efficiency of desulfurization have also been investigated. The results show that the fabrication process of AAO-CeO2 NTs is accompanied by the formation of a new phase, namely Al3Ce, and the main oxidation products of the diesel are soluble inorganic sulphides, especially Ce2(SO4)3. When compared with dibenzothiophene and 4, 6-dimethyldibenzothiophene, benzothiophene is much more easily removed, with a removal efficiency that reaches 87.2%. Finally, a possible electrochemical oxidation desulfurization pathway for diesel is proposed.

Lattice dynamics of γ--Ce

International Nuclear Information System (INIS)

Gould, T.A.

1978-08-01

The phonon and magnetic measurements described in the thesis produced the following significant results concerning the lattice dynamical and magnetic properties of γ-Ce. The phonon spectrum is relatively soft, which is consistent with results obtained for CeSn 3 . The L [110] and T [111] branches of the dispersion curve are anomalous. The C 11 and C 44 elastic constants are quite close in value. No discrete magnetic excitations were observed. The magnetic scattering is qualitatively similar to the results from Ce 0 . 74 Th 0 . 26 , however, GAMMA/sub Ce/ less than GAMMA/sub Ce-Th/. The various lattice dynamical and magnetic similarities among γ-Ce, CeSn 3 , and Ce 0 . 74 Th 0 . 26 are mixed valence compounds. Therefore, a complete theoretical description of the observed properties of Ce and its compounds may provide a basis for understanding a whole class of mixed valence materials

Application of NASVD method in the CE1-GRS spectra analysis

International Nuclear Information System (INIS)

Yang Jia; Ge Liangquan; Xiong Shengqing

2010-01-01

From the spectral shape features of the Chang'e-1 gamma-ray spectrometer (CE1-GRS) spectra data of level 3, it is difficult to identify elemental composition of the lunar surface. The paper proposes using Noise Adjusted Singular Value Decomposition (NASVD) method to qualitative analysis of CE1-GRS spectra. The result shows that a number of possible elements such as U, Th, K, Fe, Ti, Si, O, Al, Mg and Ca are qualitatively determined by this method.On the other hand, for each measured spectrum, the absolute value of the amplitude corresponding to the first spectral component indicates the total activity of its corresponding lunar surface region's radioactivity. (authors)

High-pressure modifications of CaZn2, SrZn2, SrAl2, and BaAl2: Implications for Laves phase structural trends

International Nuclear Information System (INIS)

Kal, Subhadeep; Stoyanov, Emil; Belieres, Jean-Philippe; Groy, Thomas L.; Norrestam, Rolf; Haeussermann, Ulrich

2008-01-01

High-pressure forms of intermetallic compounds with the composition CaZn 2 , SrZn 2 , SrAl 2 , and BaAl 2 were synthesized from CeCu 2 -type precursors (CaZn 2 , SrZn 2 , SrAl 2 ) and Ba 21 Al 40 by multi-anvil techniques and investigated by X-ray powder diffraction (SrAl 2 and BaAl 2 ), X-ray single-crystal diffraction (CaZn 2 ), and electron microscopy (SrZn 2 ). Their structures correspond to that of Laves phases. Whereas the dialuminides crystallize in the cubic MgCu 2 (C15) structure, the dizincides adopt the hexagonal MgZn 2 (C14) structure. This trend is in agreement with the structural relationship displayed by sp bonded Laves phase systems at ambient conditions. - Graphical abstract: CeCu 2 -type polar intermetallics can be transformed to Laves phases upon simultaneous application of pressure and temperature. The observed structures are controlled by the valence electron concentration

espèce de tilapia Sarotherodon melanotheron melanothero

African Journals Online (AJOL)

Sci-Nat

melanotheron, objet du présent travail, dont l'aire de répartition s'étend de la Côte d'Ivoire au. Cameroun. En Côte d'Ivoire, ce poisson se rencontre dans les estuaires et eaux saumâtres, depuis le fleuve Cavally (à l'Ouest) à la lagune. Aby (à l'Est) mais aussi en amont du lac de barrage du fleuve Bia (Gourène et al., 1999).

Towards atomic scale engineering of rare-earth-doped SiAlON ceramics through aberration-corrected scanning transmission electron microscopy

International Nuclear Information System (INIS)

Yurdakul, Hilmi; Idrobo, Juan C.; Pennycook, Stephen J.; Turan, Servet

2011-01-01

Direct visualization of rare earths in α- and β-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of β-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in α-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in β-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.

Dopant concentration dependence of radiation-induced positive hysteresis of Ce:GSO and Ce:GSOZ

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Watanabe, Kenichi

2014-01-01

Positive hysteresis and radiation tolerance to high-dose radiation exposure were investigated for Ce 0.5, 1, and 1.5%-doped Gd 2 SiO 5 (GSO) and for Zr co-doped GSO with the same Ce concentrations (GSOZ). When they were irradiated by 200–800 Gy 60 Co in 200 Gy steps, all Ce-doped GSO samples exhibited light yield enhancement (positive hysteresis). On the other hand, the light yield of GSOZ decreased greatly. Ce 0.5%-doped GSO showed the highest positive hysteresis, with ∼20% light yield enhancement. When the Ce concentration was increased, the positive hysteresis became weaker. - Highlights: • Positive hysteresis Ce 0.5, 1, and 1.5% doped GSO and GSOZ are studied. • Ce 0.5, 1, and 1.5% doped GSO show the positive hysteresis by 2–8 M rad 60 Co irradiation. • Ce 0.5, 1, and 1.5% doped GSOZ do not show the positive hysteresis. • By Zn co-doping, radiation tolerance of GSO becomes weaker. • By dense Ce doping, radiation tolerance of GSO and GSOZ are improved

Effects of citric acid additive on photoluminescence properties of YAG:Ce3+ nanoparticles synthesized by glycothermal reaction

International Nuclear Information System (INIS)

Asakura, R.; Isobe, T.; Kurokawa, K.; Takagi, T.; Aizawa, H.; Ohkubo, M.

2007-01-01

We synthesize Y 3 Al 5 O 12 :Ce 3+ (YAG:Ce 3+ ) nanoparticles in the presence of citric acid by glycothermal method. Fourier transform infrared absorption spectroscopy measurement indicates that the intensity of the peak corresponding to carboxyl groups coordinating to the nanoparticles increases with increasing amount of citric acid. At the same time, the primary particle diameter decreases from 10.2 to 4.0 nm. In addition, the internal quantum efficiency of the photoluminescence (PL) due to the 4f-5d transition of Ce 3+ increases from 22.0% to 40.1% with increasing amount of citric acid. Two kinds of PL decay lifetimes, 16-26 and 72-112 ns, are detected for YAG:Ce 3+ nanoparticles, whereas the micron sized YAG:Ce 3+ bulk shows the lifetime of 57 ns. We discuss these phenomena from the aspects of the coordination of citric acid and the incorporation of Ce 3+ ions into the nanoparticles

A novel gamma-ray detector with submillimeter resolutions using a monolithic MPPC array with pixelized Ce:LYSO and Ce:GGAG crystals

Energy Technology Data Exchange (ETDEWEB)

Kato, T., E-mail: katou.frme.8180@asagi.waseda.jp [Research Institute for Science and Engineering, Waseda University, 3-4-1, Ohkubo, Shinjuku, Tokyo (Japan); Kataoka, J.; Nakamori, T.; Miura, T.; Matsuda, H.; Kishimoto, A. [Research Institute for Science and Engineering, Waseda University, 3-4-1, Ohkubo, Shinjuku, Tokyo (Japan); Sato, K.; Ishikawa, Y.; Yamamura, K.; Nakamura, S.; Kawabata, N. [Solid State Division, Hamamatsu Photonics K. K., 1126-1, Ichino-cho, Hamamatsu, Shizuoka (Japan); Ikeda, H. [ISAS/JAXA, 3-1-1, Yoshinodai, Chuo-ku, Sagamihara-shi, Kanagawa (Japan); Yamamoto, S. [Kobe City College of Technology, 8-3, Gakuenhigashimati, Nishi-ku, Kobe-shi, Hyougo 651-2194 (Japan); Kamada, K. [Materials Research Laboratory, Furukawa Co., Ltd., 1-25-13, Kannondai, Tsukuba, Ibaraki 305-0856 (Japan)

2013-01-21

We have developed a large-area monolithic Multi-Pixel Photon Counter (MPPC) array consisting of 4×4 channels with a three-side buttable package. Each channel has a photosensitive area of 3×3 mm{sup 2} and 3600 Geiger mode avalanche photodiodes (APDs). For typical operational gain of 7.5×10{sup 5} at +20 °C, gain fluctuation over the entire MPPC device is only ±5.6%, and dark count rates (as measured at the 1 p.e. level) amount to ≤400kcps per channel. We first fabricated a gamma-ray camera consisting of the MPPC array with one-to-one coupling to a Ce-doped (Lu,Y){sub 2}(SiO{sub 4})O (Ce:LYSO) crystal array (4×4 array of 3×3×10 mm{sup 3} crystals). Energy and time resolutions of 11.5±0.5% (FWHM at 662 keV) and 493±22ps were obtained, respectively. When using the charge division resistor network, which compiles signals into four position-encoded analog outputs, the ultimate positional resolution is estimated as 0.19 mm in both X and Y directions, while energy resolution of 10.2±0.4% (FWHM) was obtained. Finally, we fabricated submillimeter Ce:LYSO and Ce-doped Gd{sub 3}Ga{sub 3}Al{sub 2}O{sub 12} (Ce:GGAG) scintillator matrices each consisting of 1.0×1.0, 0.7×0.7 and 0.5×0.5 mm{sup 2} pixels, to further improve the spatial resolution. In all types of Ce:LYSO and Ce:GGAG matrices, each crystal was clearly resolved in the position histograms when irradiated by a {sup 137}Cs source. The energy resolutions for 662 keV gamma-rays for each Ce:LYSO and Ce:GGAG scintillator matrix were ≤14.3%. These results suggest excellent potential for its use as a high spatial medical imaging device, particularly in positron emission tomography (PET). -- Highlights: ► We developed a newly designed large-area monolithic MPPC array. ► We obtained fine gain uniformity, and good energy and time resolutions when coupled to the LYSO scintillator. ► We fabricated gamma-ray camera consisting of the MPPC array and submillimeter pixelized LYSO and GGAG scintillators. ► In

Photostimulated luminescence and defects creation processes in Ce{sup 3+}-doped epitaxial films of multicomponent Lu{sub 3−x}Gd{sub x}Ga{sub y}Al{sub 5−y}O{sub 12} garnets

Energy Technology Data Exchange (ETDEWEB)

Babin, V. [Institute of Physics AS CR, Cukrovarnicka 10, 16253 Prague (Czech Republic); Chernenko, K. [Peter the Great Saint-Petersburg Polytechnic University, Polytekhnicheskaya 29, 195251 St. Petersburg (Russian Federation); Kučera, M. [Charles University, Faculty of Mathematics and Physics, Ke Karlovu 5, 12116 Prague (Czech Republic); Nikl, M. [Institute of Physics AS CR, Cukrovarnicka 10, 16253 Prague (Czech Republic); Zazubovich, S., E-mail: svea@ut.ee [Institute of Physics, University of Tartu, Ravila 14c, 50411 Tartu (Estonia)

2016-11-15

Luminescence characteristics of epitaxial films of Ce{sup 3+}-doped multicomponent garnets of the type of Lu{sub 3−x}Gd{sub x}Ga{sub y}Al{sub 5−y}O{sub 12}, where x varies from 0.14 to 3 and y varies from 0 to 3.54, are investigated in the 4.2–400 K temperature range by the steady-state and time-resolved spectroscopy methods. Their dependence on the film composition is clarified. The presence in the same film of different Ce{sup 3+}-related luminescence centers is revealed, and a possible structure of these centers is discussed. The processes of the electron and hole centers creation under irradiation of the films in the Ce{sup 3+}-related absorption bands are studied by thermally stimulated luminescence method. The location of the excited 5d{sub 1} level of Ce{sup 3+} with respect to the bottom of the conduction band and the origin and thermal stability parameters of electron traps in the epitaxial films and in the single crystals of the same composition are found to be different.

Luminescence, scintillation, and energy transfer in SiO{sub 2}-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-Gd{sub 2}O{sub 3}:Ce{sup 3+},Pr{sup 3+} glasses

Energy Technology Data Exchange (ETDEWEB)

Lertloypanyachai, Prapon; Chewpraditkul, Weerapong; Pattanaboonmee, Nakarin [Department of Physics, King Mongkut' s University of Technology Thonburi, Bangkok (Thailand); Chen, Danping [Shanghai Institute of Optics and Fine Mechanics, Chinese Academy of Sciences, Shanghai (China); Babin, Vladimir; Beitlerova, Alena; Nikl, Martin [Institute of Physics, AS CR, Prague (Czech Republic)

2017-09-15

Ce{sup 3+},Pr{sup 3+}-codoped SiO{sub 2}-Al{sub 2}O{sub 3}-B{sub 2}O{sub 3}-Gd{sub 2}O{sub 3} glasses (SABG:Ce,Pr) were prepared by melt quenching under a CO reducing atmosphere. Luminescence properties were investigated under UV and X-ray excitations. A dominant emission band at 430 nm belonging to the Ce{sup 3+}:5d{sub 1} → 4f transition was observed in the photo- and radio-luminescence spectra. The energy transfer occurs from this Ce{sup 3+} band toward the {sup 3}P{sub J} levels of Pr{sup 3+} with an efficiency of up to 24%, followed by the reduction of integrated luminescence intensity with an increasing Pr{sup 3+} concentration. This result is attributed to the increase in the reabsorption of Ce{sup 3+} luminescence and the non-radiative energy transfer toward the {sup 3}P{sub J} levels of Pr{sup 3+}. The cross-relaxation process within the Pr{sup 3+} pairs can further diminish the total luminescence yield at high Pr{sup 3+} concentrations. The integral scintillation efficiency and light yield measurements were carried out and compared to the reference Bi{sub 4}Ge{sub 3}O{sub 12} (BGO) crystal. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The effect of Ce ion substituted OMS-2 nanostructure in catalytic activity for benzene oxidation

Science.gov (United States)

Hou, Jingtao; Li, Yuanzhi; Mao, Mingyang; Zhao, Xiujian; Yue, Yuanzheng

2014-11-01

The nanostructure of Ce doped OMS-2 plays a very important role in its catalytic property. We demonstrate by density functional theory (DFT) calculations that the unique nanostructure of the Ce ion substituted OMS-2 with Mn vacancy in the framework is beneficial for the improvement of catalytic activity, while the nanostructure of the Ce ion substituted OMS-2 without defects are detrimental to the catalytic activity. We establish a novel and facile strategy of synthesizing these unique Ce ion substituted OMS-2 nanostructure with Mn vacancies in the framework by hydrothermal redox reaction between Ce(NO3)3 and KMnO4 with KMnO4/Ce(NO3)3 at a molar ratio of 3 : 1 at 120 °C. Compared to pure OMS-2, the produced catalyst of Ce ion substituted OMS-2 ultrathin nanorods exhibits an enormous enhancement in the catalytic activity for benzene oxidation, which is evidenced by a significant decrease (ΔT50 = 100 °C, ΔT90 = 129 °C) in the reaction temperature of T50 and T90 (corresponding to the benzene conversion = 50% and 90%), which is considerably more efficient than the expensive supported noble metal catalyst (Pt/Al2O3). We combine both theoretical and experimental evidence to provide a new physical insight into the significant effect due to the defects induced by the Ce ion substitution on the catalytic activity of OMS-2. The formation of unique Ce ion substituted OMS-2 nanostructure with Mn vacancies in the framework leads to a significant enhancement of the lattice oxygen activity, thus tremendously increasing the catalytic activity.The nanostructure of Ce doped OMS-2 plays a very important role in its catalytic property. We demonstrate by density functional theory (DFT) calculations that the unique nanostructure of the Ce ion substituted OMS-2 with Mn vacancy in the framework is beneficial for the improvement of catalytic activity, while the nanostructure of the Ce ion substituted OMS-2 without defects are detrimental to the catalytic activity. We establish a novel

Macrodynamic study and catalytic reduction of NO by ammonia under mild conditions over Pt-La-Ce-O/Al2O3 catalysts

International Nuclear Information System (INIS)

Wang, Yanhui; Zhu, Jingli; Ma, Runyu

2007-01-01

Catalytic reduction of NO using ammonia upon series prepared catalysts under 423-573 K in a fixed bed reactor was investigated. Results showed that the performance of supported platinum catalyst could be improved by addition of La and Ce to it. Experimental studies indicated that the suitable molar ratio of Pt:La:Ce would be 1.0:3.78:3.56, Pt-La-Ce (c). Results also found Pt-La-Ce (c) catalyst had good stability and tolerance to certain amounts of sulfur compounds under the used experimental conditions. Characterization for the fresh and used catalysts showed the Pt-La-Ce (c) catalyst had a stable structure. In addition, based on experimental data and using a nonlinear regression algorithm method, an empirical macrodynamic equation was obtained in this study

Biological reduction-deposition and luminescent properties of nanostructured CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Yu, Xiaoniu [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Research Institute of Green Construction Materials, Southeast University, Nanjing 211189 (China); Qian, Chunxiang, E-mail: cxqian@seu.edu.cn [School of Materials Science and Engineering, Southeast University, Nanjing 211189 (China); Research Institute of Green Construction Materials, Southeast University, Nanjing 211189 (China)

2016-03-01

Nano-sized CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} with hexagonal phase have been prepared by simply varying the reactant P/Ce molar ratio in bacterial liquid. The phase composition of two samples was checked via Fourier transform infrared spectroscopy (FTIR), energy dispersive analysis of X-rays (EDS) and X-ray diffraction (XRD) analyses, displaying the presence of CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} with average crystallite size are 32.34 and 15.61 nm, respectively. The scanning electron microscopy (SEM) images show that nano-clusters and sphere-like in shape with a narrow diameter distribution were observed in two samples. The transmission electron microscopy (TEM) photographs further indicate obtained CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} nanoparticles correspond to nanosheets and nanorods, respectively. The emission spectra of CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} display a broad band of 300–380 nm range with the strongest emission at 342 nm in the violet region. - Highlights: • A new method was found to synthesize CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) and CePO{sub 4} nanoparticles. • CePO{sub 4}@NaCe(SO{sub 4}){sub 2}(H{sub 2}O) nanoparticles have good luminescent properties. • Size and luminescent properties of two samples have been studied and compared.

Oxidation behaviour of cast aluminium matrix composites with Ce surface coatings

International Nuclear Information System (INIS)

Pardo, A.; Merino, M.C.; Arrabal, R.; Feliu, S.; Viejo, F.

2007-01-01

The oxidation behaviour of SiC-reinforced aluminium matrix composites (A3xx.x/SiCp) has been studied after Ce-based treatments. Kinetics data of oxidation process were obtained from gravimetric tests performed at different temperatures (350, 425 and 500 o C). The nature of the oxidation layer was analyzed by scanning electron and atomic force microscopy, energy dispersive X-ray analysis, X-ray photoelectron spectroscopy and X-ray diffraction. The extent of oxidation degradation in untreated composites was preferentially localized in matrix/SiCp interfaces favouring the MgO formation. Ce coatings favoured a uniform oxidation of the composite surface with MgAl 2 O 4 spinel formation. This oxide increased the surface hardness of the materials

Temperature dependence of Ce:YAG single-crystal phosphors for high-brightness white LEDs/LDs

Science.gov (United States)

Arjoca, Stelian; Víllora, Encarnación G.; Inomata, Daisuke; Aoki, Kazuo; Sugahara, Yoshiyuki; Shimamura, Kiyoshi

2015-05-01

The growth of Ce:Y3Al5O12(Ce:YAG) single-crystal phosphors (SCPs) by the Czochralski technique is analyzed in terms of segregation coefficient, solubility and absorption cross-section. The emission characteristics of these SCPs are investigated in a wide temperature range, from liquid He temperature up to 500 °C. The internal quantum efficiency of SCPs achieves its maximum at about 250 °C. Thermal quenching of SCPs at high temperature is attributed to the Mott-Seitz mechanism. In the case of ceramic powder phosphors, a continuous droop is observed with the temperature due to defect-related non-radiative recombination paths. It is shown that (Ce:YAG SCPs + blue LEDs/LDs) can cover a wide range of color temperatures 5500-7000 K, with color rendering indices around 70. In conclusion, it is shown that Ce:YAG SCPs are the most efficient and temperature stable converters to fabricate high-brightness white light sources with high-power blue LEDs and LDs.

Discapacidad y configuración del Capital Emocional (CE: el caso de tres padres

Directory of Open Access Journals (Sweden)

Nora Aneth Pava Ripoll

2017-01-01

Full Text Available El objetivo del artículo es mostrar la configuración del CE a partir del análisis de los relatos de vida de tres padres cuyos hijos e hijas presentan discapacidad. Los argumentos de las teorías de los campos sociales de Bourdieu y de la antropología de las emociones planteada por Hochschild aportan al piso teórico del concepto. La metodología utilizada fue el enfoque narrativo-biográfico a través de los relatos de vida. Se concluye que el CE surge desde la ruptura ideológica -de la normalidad- que ocurre en el momento del diagnóstico de discapacidad de sus hijos e hijas, pero se acumula desde la confrontación con la estructura social. Sólo uno de los padres logra adquirir CE, pues cuando las personas viven sus vidas en marcos ideológicos establecidos que no se cuestionan, es imposible acumular CE.

Magnetic susceptibility and electron–phonon (e–p) interaction in some U and Ce based heavy fermion (HF) systems

International Nuclear Information System (INIS)

Sahoo, J.; Shadangi, N.; Nayak, P.

2015-01-01

Here an attempt is made to explore the variation of magnetic susceptibility with temperature for different values of the position of f-level (d) and electron–phonon interaction (EPI) strength (r) in some U and Ce based heavy Fermion (HF) systems within Periodic Anderson Model (PAM) in the presence of a static magnetic field B and interaction of phonons with electrons of hybridization band. Since magnetic susceptibility χ is related to the f-electron occupation n ±σ f , the expression for the latter is analytically derived through f–f correlation function following the Green function technique of Zubarev. The numerical analysis of χ as a function of temperature ‘T’ is done for different values of d and r. The results show a good agreement with the experiments for some U and Ce based HFs. An explanation for the existence of a critical value of d w.r.t. E F for switching of nature of χ∼T from U to Ce based HF systems is provided. Our calculated value of the temperature T χmax corresponding to the peak position of χ for small values of hybridization constant γ=0.002 and 0.0036 coincides with the experimental value of 19 K for UPt 3 and 35 K for UPd 2 Al 3 reported by Frings et al. and Geibel et al. respectively. - Highlights: • Variation of magnetic susceptibility χ with temperature T is studied for some HF systems. • Periodic Anderson Model in presence of magnetic field and electron–phonon interaction is used for numerical evaluation. • The existence of a critical value of the position of f-level(d) is proposed for distinction between χ∼T behavior of U and Ce based HF systems. • Results obtained are in good agreement with the experimental observations for some Ce and U based HF systems. • Theoretically evaluated temperature corresponding to the peak value of χ matches with the experimental results of UPt 3 and UPd 2 Al 3

Magnetic and electronic properties in CeTSi3 and CeTGe3 (T: transition metal)

International Nuclear Information System (INIS)

Shimoda, T.; Okuda, Y.; Takeda, Y.; Ida, Y.; Miyauchi, Y.; Kawai, T.; Fujie, T.; Sugitani, I.; Thamizhavel, A.; Matsuda, T.D.; Haga, Y.; Takeuchi, T.; Nakashima, M.; Settai, R.; Onuki, Y.

2007-01-01

We investigated the magnetic properties of CeTSi 3 (T: Ru, Os, Co, Rh, Ir, Pd and Pt) and CeTGe 3 (T: Co, Rh and Ir) by measuring their electrical resistivity and magnetic susceptibility. CeRuSi 3 , CeOsSi 3 and CeCoSi 3 do not order magnetically, with a large Kondo temperature of about 200K. The other compounds order antiferromagnetically, and are very similar to each other in their magnetic and electronic properties, which is related to a large crystalline electric field (CEF) splitting energy of the 4f electron, about 500K in CeIrSi 3

Formation of Broensted acids sites in the reaction of cyclohexanol on NaCeY zeolites

International Nuclear Information System (INIS)

Vogt, O.; Nattich, M.; Datka, J.; Gil, B.

2002-01-01

This study was undertaken to elucidate why the catalytic activity of NaCeY in cyclohexanol reactions carried out in a pulse reactor increases with the pulse number. We studied therefore the effect of cyclohexanol and also of ethanol and water on catalytic activity NaCeY (of exchange degrees 36 and 72%) in cyclohexanol reactions: isomerization and disproportionation. We also studied the reaction of cyclohexanol and water with NaCeY zeolite by IR spectroscopy. Our results evidenced that new Broensted acid sites were formed by the reaction of cyclohexanol and water. This was shown by IR spectroscopy: the increase of Si-O 1 H-Al band 3638 cm -1 and in increase of ammonium ions band (upon ammonia adsorption). The new sites were formed by hydrolysis of Ce 3+ ions with water introduced in a pulse, or produced by dehydration of cyclohexanol catalyzed by acid sites. Formation of new Broensted acid sites resulted in an increase of catalytic activity of NaCeY in cyclohexane reaction as observed in this study and also in cyclohexanol reactions. (author)

Free carrier absorption in self-activated PbWO_4 and Ce-doped Y_3(Al_0.25Ga_0.75)_3O_12 and Gd_3Al_2Ga_3O_12 garnet scintillators

CERN Document Server

Auffray, E.; M.T. Lucchini; S. Nargelas; O. Sidletskiy; G. Tamulaitis; Y. Tratsiak; A. Vaitkevičius

2016-01-01

tungstate (PbWO_4, PWO) ant two garnet crystals, GAGG:Ce and YAGG:Ce. It was shown that free electrons appear in the conduction band of PWO and YAGG:Ce crystals within a sub-picosecond time scale, while the free holes in GAGG:Ce appear due to delocalization from Gd^3+ ground states to the valence band within a few picoseconds after short-pulse excitation. The influence of Gd ions on the nonequilibrium carrier dynamics is discussed on the base of comparison the results of the free carrier absorption in GAGG:Ce containing gadolinium and in YAGG without Gd in the host lattice.

Scintillation properties of selected oxide monocrystals activated with Ce and Pr

Science.gov (United States)

Wojtowicz, Andrzej J.; Drozdowski, Winicjusz; Wisniewski, Dariusz; Lefaucheur, Jean-Luc; Galazka, Zbigniew; Gou, Zhenhui; Lukasiewicz, Tadeusz; Kisielewski, Jaroslaw

2006-01-01

In the last 10-15 years there has been a significant effort toward development of new, more efficient and faster materials for detection of ionizing radiation. A growing demand for better scintillator crystals for detection of 511 keV gamma particles has been due mostly to recent advances in modern imaging systems employing positron emitting radionuclides for medical diagnostics in neurology, oncology and cardiology. While older imaging systems were almost exclusively based on BGO and NaI:Tl crystals the new systems, e.g., ECAT Accel, developed by Siemens/CTI, are based on recently discovered and developed LSO (Lu 2SiO 5:Ce, Ce-activated lutetium oxyorthosilicate) crystals. Interestingly, despite very good properties of LSO, there still is a strong drive toward development of new scintillator crystals that would show even better performance and characteristics. In this presentation we shall review spectroscopic and scintillator characterization of new complex oxide crystals, namely LSO, LYSO, YAG, LuAP (LuAlO 3, lutetium aluminate perovskite) and LuYAP activated with Ce and Pr. The LSO:Ce crystals have been grown by CTI Inc (USA), LYSO:Ce, LuAP:Ce and LuYAP:Ce crystals have been grown by Photonic Materials Ltd., Scotland (PML is the only company providing large LuAP:Ce crystals on a commercial scale), while YAG:Pr and LuAP:Pr crystals have been grown by Institute of Electronic Materials Technology (Poland). All these crystals have been characterized at Institute of Physics, N. Copernicus University (Poland). We will review and compare results of measurements of radioluminescence, VUV spectroscopy, scintillation light yields, scintillation time profiles and low temperature thermoluminescence performed on these crystals. We will demonstrate that all experiments clearly indicate that there is a significant room for improvement of LuAP, LuYAP and YAG. While both Ce-activated LSO and LYSO perform very well, we also note that LuYAP:Ce, LuAP:Ce and YAG:Pr offer some

Structural and magnetic properties of Ce/Fe and Ce/FeCoV multilayers

Energy Technology Data Exchange (ETDEWEB)

Tixier, S; Boeni, P [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Mannix, D; Stirling, W G [Liverpool Univ. (United Kingdom); Lander, G H

1997-09-01

Ce/Fe and Ce/FeCoV multilayers have been grown by magnetron sputtering. The interfaces are well defined and the layers are crystalline down to an individual layer thickness of 20 A. Ce/FeCoV multilayers show sharper interfaces than Ce/Fe but some loss of crystallinity is observed. Hysteresis loops obtained by SQUID show different behaviour of the bulk magnetisation as a function of the layer thickness. Fe moments are found by Moessbauer spectroscopy to be perpendicular to the interfaces for multilayers with small periodicity. (author) 2 figs., 2 refs.

Transient oxidation of Al-deposited Fe-Cr-Al alloy foil

International Nuclear Information System (INIS)

Andoh, A.

1997-01-01

The oxide phases formed on an Al-deposited Fe-Cr-Al alloy foil and an Fe-Cr-Al alloy foil of the same levels of Al and (La+Ce) contents, and their oxidation kinetics have been studied in air at 1173 and 1373 K using TGA, XRD and SEM. Al deposition promotes the growth of metastable aluminas (θ-Al 2 O 3 , γ-Al 2 O 3 ). Scales consisting of θ-Al 2 O 3 and a small amount of α-Al 2 O 3 develop on the Al-deposited foil at 1173 K and exhibit the whisker-type morphology. In the early stage of oxidation at 1373 K, thick scales consisting of θ-Al 2 O 3 and α-Al 2 O 3 grow rapidly on the Al-deposited foil. The transformation from θ-Al 2 O 3 to α-Al 2 O 3 is very fast, and the scales result in only α-Al 2 O 3 . In contrast, α-Al 2 O 3 scales containing a minor amount of FeAl 2 O 4 develop on the alloy foil. The growth rate of α-Al 2 O 3 scales on the Al-deposited foil is smaller than that on the alloy foil and very close to that on NiAl at 1373 K. (orig.)

Inhibition of human carboxylesterases hCE1 and hiCE by cholinesterase inhibitors.

Science.gov (United States)

Tsurkan, Lyudmila G; Hatfield, M Jason; Edwards, Carol C; Hyatt, Janice L; Potter, Philip M

2013-03-25

Carboxylesterases (CEs) are ubiquitously expressed proteins that are responsible for the detoxification of xenobiotics. They tend to be expressed in tissues likely to be exposed to such agents (e.g., lung and gut epithelia, liver) and can hydrolyze numerous agents, including many clinically used drugs. Due to the considerable structural similarity between cholinesterases (ChE) and CEs, we have assessed the ability of a series of ChE inhibitors to modulate the activity of the human liver (hCE1) and the human intestinal CE (hiCE) isoforms. We observed inhibition of hCE1 and hiCE by carbamate-containing small molecules, including those used for the treatment of Alzheimer's disease. For example, rivastigmine resulted in greater than 95% inhibition of hiCE that was irreversible under the conditions used. Hence, the administration of esterified drugs, in combination with these carbamates, may inadvertently result in decreased hydrolysis of the former, thereby limiting their efficacy. Therefore drug:drug interactions should be carefully evaluated in individuals receiving ChE inhibitors. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Effect of similar elements on improving glass-forming ability of La-Ce-based alloys

International Nuclear Information System (INIS)

Zhang Tao; Li Ran; Pang Shujie

2009-01-01

To date the effect of unlike component elements on glass-forming ability (GFA) of alloys have been studied extensively, and it is generally recognized that the main consisting elements of the alloys with high GFA usually have large difference in atomic size and atomic interaction (large negative heat of mixing) among them. In our recent work, a series of rare earth metal-based alloy compositions with superior GFA were found through the approach of coexistence of similar constituent elements. The quinary (La 0.5 Ce 0.5 ) 65 Al 10 (Co 0.6 Cu 0.4 ) 25 bulk metallic glass (BMG) in a rod form with a diameter up to 32 mm was synthesized by tilt-pour casting, for which the glass-forming ability is significantly higher than that for ternary Ln-Al-TM alloys (Ln = La or Ce; TM = Co or Cu) with critical diameters for glass-formation of several millimeters. We suggest that the strong frustration of crystallization by utilizing the coexistence of La-Ce and Co-Cu to complicate competing crystalline phases is helpful to construct BMG component with superior GFA. The results of our present work indicate that similar elements (elements with similar atomic size and chemical properties) have significant effect on GFA of alloys.

Ce(III)/Ce(IV) in methanesulfonic acid as the positive half cell of a redox flow battery

International Nuclear Information System (INIS)

Leung, P.K.; Ponce de Leon, C.; Low, C.T.J.; Walsh, F.C.

2011-01-01

The characteristics of the Ce(III)/Ce(IV) redox couple in methanesulfonic acid were studied at a platinum disk electrode (0.125 cm 2 ) over a wide range of electrolyte compositions and temperatures: cerium (III) methanesulfonate (0.1-1.2 mol dm -3 ), methanesulfonic acid (0.1-5.0 mol dm -3 ) and electrolyte temperatures (295-333 K). The cyclic voltammetry experiments indicated that the diffusion coefficient of Ce(III) ions was 0.5 x 10 -6 cm 2 s -1 and that the electrochemical kinetics for the oxidation of Ce(III) and the reduction of Ce(IV) was slow. The reversibility of the redox reaction depended on the electrolyte composition and improved at higher electrolyte temperatures. At higher methanesulfonic acid concentrations, the degree of oxygen evolution decreased by up to 50% when the acid concentration increased from 2 to 5 mol dm -3 . The oxidation of Ce(III) and reduction of Ce(IV) were also investigated during a constant current batch electrolysis in a parallel plate zinc-cerium flow cell with a 3-dimensional platinised titanium mesh electrode. The current efficiencies over 4.5 h of the process Ce(III) to Ce(IV) and 3.3 h electrolysis of the reverse reaction Ce(IV) to Ce(III) were 94.0 and 97.6%, respectively. With a 2-dimensional, planar platinised titanium electrode (9 cm 2 area), the redox reaction of the Ce(III)/Ce(IV) system was under mass-transport control, while the reaction on the 3-dimensional mesh electrode was initially under charge-transfer control but became mass-transport controlled after 2.5-3 h of electrolysis. The effect of the side reactions (hydrogen and oxygen evolution) on the current efficiencies and the conversion of Ce(III) and Ce(IV) are discussed.

Role of cerium, lanthanum, and strontium additions in an Al-Si-Mg (A356) alloy

Energy Technology Data Exchange (ETDEWEB)

Nabawy, Ahmed M.; Samuel, Agnes M.; Samuel, Fawzy H. [Universite du Quebec, Chicoutimi (Canada). Dept. des Sciences Appliquees; Alkahtani, Saleh A.; Abuhasel, Khaled A. [Salman Bin Abdulaziz Univ., Riyadh (Saudi Arabia). Mechanical Engineering Dept.

2016-05-15

The effects of individual and combined additions of cerium (Ce), lanthanum (La), and strontium (Sr) on the eutectic modification and solidification characteristics of an Al-Si-Mg (A356) aluminum alloy were investigated using optical microscopy and thermal analysis techniques. Addition of Ce, La, and Sr resulted in different depression levels of the eutectic nucleation temperature and eutectic growth undercooling, generating modified eutectic structures exhibiting different levels of modification. Microstructural results showed that the best modification levels using individual additions were achieved by Sr which produced a fine fibrous eutectic structure, followed by La, which produced a refined lamellar structure, with Ce providing the lowest level of modification. On the other hand, a combined addition of Ce and Sr provided the highest modification level, with the production of a very fine fibrous eutectic silicon structure. In general, the addition of Sr helped to further increase the refinement obtained in the alloys containing La or Ce + La additions. In the latter alloy, the main intermetallic phases observed were La(Al,Si){sub 2} and Al{sub 20}(La,Ce)Ti{sub 2}Si. The improved modification levels were found to be proportional to the depression in the eutectic nucleation temperature and the eutectic growth undercooling. A high cooling rate also improved the modification level by at least one level.

Microstructures and mechanical properties of the Ce containing cast iron super-rapidly melted. Chokosoku yokaishita gan seriumu chutetsu no soshiki to kikaiteki seishitsu

Energy Technology Data Exchange (ETDEWEB)

Kowata, T.; Hiratsuka, S.; Horie, H. (Iwate Univ., Iwate (Japan). Faculty of Engineering); Matsumoto, T. (Taiyo Steel Co. Ltd., Tokyo (Japan))

1994-04-25

Spheroidal graphite cast iron and CV graphite cast iron were prepared by super-rapid remelting of parent alloys containing definite amounts of cerium (Ce) in a high frequency and super-rapid induction smelting furnace. Their graphite structure, amounts of Ce remained and mechanical properties were investigated by comparing with those prepared by ordinary remelting. Further, super-rapid remelting of parent alloys added with aluminum (Al) or titanium (Ti) was investigated to make certain whether it stabilizes the CV graphite structure. The results obtained are summarized as follows. Mere remelting of Ce-added parent alloys is sufficient to yield CV and spheroidal graphite structures. Whereas the yield of Ce melted remains at 28% in ordinary remelting, that in the super-rapid remelting reaches 63%. Whereas the Ce amount needed in parent alloys to get CV graphite structures is 0.08% in ordinary remelting, that in super-rapid remelting is 0.025%. The addition of Al shows no inhibitory effect on graphite spheroidation. On the contrary, it raises the degree of spheroidization. The addition of Ti inhibits the spheroidization, whereby the amount range of Ce remaining to be embedded in the graphite structure can be extended, thus ensuring stable production of CV graphite cast iron. 5 refs., 11 figs., 2 tabs.

Dynamics of laser-induced magnetization in Ce-doped yttrium aluminum garnet

International Nuclear Information System (INIS)

Kolesov, Roman

2007-01-01

Circularly polarized short laser pulse induces nonequilibrium population of spin levels in the excited state of Ce 3+ -ion embedded in yttrium aluminium garnet crystal and, consequently, the magnetization of the crystal associated with spin polarization. Dynamic behavior of laser-induced magnetization is studied as a function of the external magnetic field. It reveals spin oscillations attributed to the effect of hyperfine magnetic field produced by 27 Al nuclei on the Ce 3+ spin. A simple theoretical model explaining spin oscillations is presented. It shows that circularly polarized light induces spin coherence at the transition between Zeeman sublevels of Ce 3+ ion in the lowest 5d state. Temporal shape of laser-induced magnetization signal reveals the following parameters of this state: (1) the spin-lattice relaxation constant is ≅2x10 7 s -1 , (2) inhomogeneous spin dephasing time is ≅4 ns, and (3) the g tensor of the state seems to be isotropic with the g factor being in the range 0.7-0.9. In addition, the width of the local hyperfine field distribution is ≅40 G

Nature of the magnetic ground state in the mixed valence compound CeRuSn: a single-crystal study

International Nuclear Information System (INIS)

Fikáček, J; Prokleška, J; Prchal, J; Custers, J; Sechovský, V

2013-01-01

We report on detailed low-temperature measurements of the magnetization, the specific heat and the electrical resistivity on high-quality CeRuSn single crystals. The compound orders antiferromagnetically at T N = 2.8 K with the Ce 3+ ions locked within the a–c plane of the monoclinic structure. Magnetization shows that below T N CeRuSn undergoes a metamagnetic transition when applying a magnetic field of 1.5 and 0.8 T along the a- and c-axis, respectively. This transition manifests in a tremendous negative jump of ∼25% in the magnetoresistance. The value of the saturated magnetization along the easy magnetization direction (c-axis) and the magnetic entropy above T N derived from specific heat data correspond to the scenario of only one third of the Ce ions in the compound being trivalent and carrying a stable Ce 3+ magnetic moment, whereas the other two thirds of the Ce ions are in a nonmagnetic tetravalent and/or mixed valence state. This is consistent with the low-temperature CeRuSn crystal structure i.e., a superstructure consisting of three unit cells of the CeCoAl type piled up along the c-axis, and in which the Ce 3+ ions are characterized by large distances from the Ru ligands while the Ce–Ru distances of the other Ce ions are much shorter causing a strong 4f-ligand hybridization and hence leading to tetravalent and/or mixed valence Ce ions. (paper)

Rem Koolhaas y la nueva Babel. De la torre metropolitana al monumento al vacío

Directory of Open Access Journals (Sweden)

José Antonio Tallón

2015-05-01

Full Text Available Un primer acercamiento a las reflexiones de Rem Koolhaas en torno a la tipología de torre introduce al rascacielos neoyorquino como la alegoría del “automonumen­to”: una construcción en esencia destinada a reafirmar su sola presencia y que se distingue del resto por medio de su estatura, que la monumentaliza. La torre de Babel, símbolo inquebrantable de la leyenda de la construcción en altura, escenifi­ca una historia de construcción y destrucción que está vinculada ineludiblemente al pensamiento crítico de Rem Koolhaas en torno a la torre como tipología desa­creditada. Un recorrido por las distintas “Babel” que Rem Koolhaas cataloga en el glosario de términos incluido en el texto SMLXL construye un discurso en torno a la destrucción de la torre bíblica y la construcción de la nueva Babel koolhaasiana que inicia su recorrido con el rascacielos para acabar reclamando un nuevo estado de monumentalidad: la ausencia en su estado más puro representado por el muro, el máximo ejemplo de ausencia como la forma más elevada de presencia monu­mental. Una mirada crítica que comienza con la torre metropolitana como la nueva Babel para finalizar con el muro como el monumento al vacío

Thermal neutron imaging with rare-earth-ion-doped LiCaAlF6 scintillators and a sealed 252Cf source

International Nuclear Information System (INIS)

Kawaguchi, Noriaki; Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Kamada, Kei; Fukuda, Kentaro; Suyama, Toshihisa; Watanabe, Kenichi; Yamazaki, Atsushi; Chani, Valery; Yoshikawa, Akira

2011-01-01

Thermal neutron imaging with Ce-doped LiCaAlF 6 crystals has been performed. The prototype of the neutron imager using a Ce-doped LiCaAlF 6 scintillating crystal and a position sensitive photomultiplier tube (PSPMT) which had 64 multi-channel anode was developed. The Ce-doped LiCaAlF 6 single crystal was grown by the Czochralski method. A plate with dimensions of a diameter of 50x2 mm 2 was cut from the grown crystal, polished, and optically coupled to PSPMT by silicone grease. The 252 Cf source ( 6 .

Optical and scintillation properties of Ce.sup.3+./sup.-doped YGd.sub.2./sub.Al.sub.5-x./sub.Ga.sub.x./sub.O.sub.12./sub. (x=2,3,4) single crystal scintillators

Czech Academy of Sciences Publication Activity Database

Chewpraditkul, Wa.; Brůža, P.; Pánek, D.; Pattanaboonmee, N.; Wantong, K.; Chewpraditkul, W.; Babin, Vladimir; Bartosiewicz, Karol; Kamada, K.; Yoshikawa, A.; Nikl, Martin

2016-01-01

Roč. 169, Jan (2016), s. 43-50 ISSN 0022-2313 R&D Projects: GA ČR GAP204/12/0805; GA MŠk(CZ) LH14266 EU Projects: European Commission(XE) 316906 - LUMINET Institutional support: RVO:68378271 Keywords : YGd 2 Al 5-x Ga x O 12 :Ce * light yield * luminescence * scintillation Subject RIV: BH - Optics, Masers, Lasers Impact factor: 2.686, year: 2016

Influence of microgravity on Ce-doped Bi12 SiO20 crystal defect

Indian Academy of Sciences (India)

TECS

studied by comparing space grown BSO crystal with ground grown one. These results show ... fractive properties (Aldrich et al 1971; Peltier and. Micheron ... The shape of interface changes from concave to convex by suppressing ... cations. Figure 1. Parts of Ce doped BSO crystals: (a) space growth and (b) ground growth.

Phase equilibria and crystalline structure of compounds in the Lu-Al and Lu-Cu-Al systems

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Stel'makhovich, B.M.; Galamushka, L.I.

1992-01-01

Phase equilibria and crystal structure of compounds in Lu-Al and Lu-Cu-Al systems were studied. Existence of Lu 2 Al compound having the structure of the PbCl 2 type is ascertained. Diagram of phase equilibria of Lu-Cu-Al system at 870 K is plotted. Compounds Lu 2 (Cu,Al) 17 (the Th 2 Zn 17 type structure), Lu(Cu,Al) 5 (CaCu 5 type structure), Lu 6 (Cu,Al) 23 (Th 6 Mn 23 type structure) and ∼ LuCuAl 2 have been prepared for the first time. Investigation of component interaction in Lu-Cu-Al system shows that the system is similar to previously studied systems Dy-Cu-Al and Er-Cu-Al. The main difference consists in the absence of LuCuAl 3 compound with rhombic structure of the CeNi 2+x Sb 2-x type in the system investigated

Chemical durability and resistance to irradiation of LnYSiAlO (Ln=La or Ce) glasses, potential immobilization matrix of minor actinides

International Nuclear Information System (INIS)

Gavarini, St.

2002-11-01

Rare earth aluminosilicate glasses are known for their interesting mechanical and optical properties. Recent studies have shown that their chemical durability was very good too, such they have the potential to be used in the nuclear industry for the specific immobilization of trivalent actinides. Initial dissolution rates of LaYSiAlO and CeYSiAlO were determined using a Soxhlet device (dynamic leaching). The differences linked to the nature of the rare earth element were studied by synthesizing analogous glasses that only differed in their rare earth element composition (%at.): Y-5%, La-5 %, Si-15%, Al-10% O-65%. The influence of pH on the dissolution mechanisms and kinetics was also studied by static leaching tests performed in dilute solutions of NaOH or HNO 3 . Electronic defects and collision cascades, induced by a-disintegration of radioelements confined in storage matrix, can cause important modifications in the glass structure and, thus, influence its chemical durability. To simulate these effects, glass samples were irradiated with β particles and heavy ions accelerated to 2,5 MeV and 200 keV, respectively. Monoliths were then leached in static bi-distilled water (pH≥≥ 5.5) for one month in an autoclave heated to 90 degrees C. Initially, the structural changes caused by irradiation were determined using Raman, NMR and EPR spectroscopies. Ion μ-beams, SEM-EDS and XPS analysis were also performed to evaluate the potential modifications of the superficial composition. Finally, the leaching behavior was studied, for both irradiated and unirradiated samples, through solution and solid elementary characterization. (author)

First-principles study of atomic ordering in bcc Cu-Al

Science.gov (United States)

Lanzini, F.; Gargano, P. H.; Alonso, P. R.; Rubiolo, G. H.

2011-01-01

The order-disorder transitions and phase stability in the body centered cubic structure of Cu-Al binary alloys are studied by means of theoretical methods. The total energy of different ordered compounds sharing a common bcc Bravais lattice was calculated within the framework of density functional theory. A set of effective cluster interactions was calculated through a cluster expansion (CE) of the total energies. The finite temperature phase diagram of bcc Cu-Al was obtained using the CE formalism coupled with the cluster variation method calculation of the configurational entropy. These results are confronted with a simpler semi-empirical approach based on effective pair interactions obtained from experiment. Both approaches predict a single first-order A2/DO3 transition for compositions close to Cu3Al, in agreement with the most recent experimental results.

Effect of thermal annealing on scintillation properties of Ce:Gd{sub 2}Y{sub 1}Ga{sub 2.7}Al{sub 2.3}O{sub 12} under different atmosphere

Energy Technology Data Exchange (ETDEWEB)

Wang, Chao; Ding, Dongzhou; Wu, Yuntao; Li, Huanying; Chen, Xiaofeng; Shi, Jian; Wang, Qingqing; Ye, Le; Ren, Guohao [Chinese Academy of Sciences, Shanghai Institute of Ceramics, Shanghai (China)

2017-05-15

Cerium-doped 1% Ce:Gd{sub 2}Y{sub 1}Ga{sub 2.7}Al{sub 2.3}O{sub 12}(GYGAG) single crystal samples grown via Czochralski method were annealed under air, O{sub 2} and N{sub 2} atmospheres from 350 to 1400 C. The X-ray excited luminescence spectra, energy spectra and UV as well as thermally stimulated luminescence (TSL) spectra were performed comparatively on ''as-grown'' and thermally annealed samples. It was found that the luminescence efficiency after annealing in air and O{sub 2} was significantly enhanced compared to the non-annealed samples and this phenomenon was suggested to be caused by the existence of some oxygen vacancies in the Ce:GYGAG crystals. And the oxygen vacancies in the as-grown GYGAG crystals can be effectively eliminated by means of annealing in O{sub 2} containing atmosphere without changing the luminescence mechanism. From the TSL curves before and after annealing, three traps within 77-650 K were found to be related to oxygen vacancies. (orig.)

On possibility of BaCeO3 production when depositing YBa2Cu3O7-χ films on a cerium oxide surface

International Nuclear Information System (INIS)

Mashtakov, A.D.; Kotelyanskij, I.M.; Luzanov, V.A.; Mozhaev, P.B.; Ovsyannikov, G.A.; Bdikin, I.D.

1997-01-01

Consideration is given to experimental results of investigation into crystallographic parameters of hetero-structural (1102)Al 2 O 3 /(001)CeO 2 (001)YBa 2 Cu 3 O 7-χ films, prepared by the method of cathode sputtering at substrate temperature, equal to 600-800 deg C. It is shown that main limitation for precipitation temperature of YBa 2 Cu 3 O 7-χ film on CeO 2 surface is caused by chemical interaction of YBa 2 Cu 3 O 7-χ with CeO 2 with formation of polycrystalline BaCeO 3 layer

Evolution mechanisms of MgO·Al2O3 inclusions by cerium in spring steel used in fasteners of high-speed railway

International Nuclear Information System (INIS)

Wang Lijun; Wang Qi; Chou Kuochih; Liu Yanqiang

2015-01-01

The effect of rare earth metal addition on the non-metallic inclusions in spring steel used in fastener of high speed railway was investigated by metallographic examination; SEM-EDS and component analysis, aiming at deform those harmful inclusions to improve service life of spring steel. MgO·Al 2 O 3 inclusions were found in present experimental steel, which is also confirmed by the stability diagram of MgO/MgO·Al 2 O 3 /Al 2 O 3 from thermodynamic consideration. After Ce addition, the evolution process of Al 2 O 3 ·MgO inclusions was determined through the surface and line scanning. The effects of time and Ce content on the evolution of Al 2 O 3 ·MgO inclusions were examined. It was indicated that Al 2 O 3 ·MgO inclusions were wrapped by rare earth inclusions to form a ring like shape Ce-riched band around the inclusion, which would be useful to improve fatigue and corrosion resistance of spring steel. It was found that diffusion of Ce 3+ , Al 3+ and Mg 2+ in inclusions core and intermediate layer would be the limited step during evolutions of inclusions. (author)

Photoluminescence, energy transfer and tunable color of Ce(3+), Tb(3+) and Eu(2+) activated oxynitride phosphors with high brightness.

Science.gov (United States)

Lü, Wei; Huo, Jiansheng; Feng, Yang; Zhao, Shuang; You, Hongpeng

2016-06-21

New tuneable light-emitting Ca3Al8Si4O17N4:Ce(3+)/Tb(3+)/Eu(2+) oxynitride phosphors with high brightness have been prepared. When doped with trivalent cerium or divalent europium they present blue luminescence under UV excitation. The energy transfer from Ce(3+) to Tb(3+) and Ce(3+) to Eu(2+) ions is deduced from the spectral overlap between Ce(3+) emission and Tb(3+)/Eu(2+) excitation spectra. The energy-transfer efficiencies and corresponding mechanisms are discussed in detail, and the mechanisms of energy transfer from the Ce(3+) to Tb(3+) and Ce(3+) to Eu(2+) ions are demonstrated to be a dipole-quadrupole and dipole-dipole mechanism, respectively, by the Inokuti-Hirayama model. The International Commission on Illumination value of color tuneable emission as well as luminescence quantum yield (23.8-80.6%) can be tuned by controlling the content of Ce(3+), Tb(3+) and Eu(2+). All results suggest that they are suitable for UV light-emitting diode excitation.

Os procedimentos adotados pelos Tribunais de Contas da Bahia para a verificação das receitas e despesas vinculadas à educação Los procedimientos adoptados por los Tribunales de Cuentas del estado brasileño de Bahia para la verificación de ingresos y despesas vinculadas a la educación The procedures adopted by the Audit Courts of Bahia for checking revenue and expenses linked to education

Directory of Open Access Journals (Sweden)

Nicholas Davies

2010-03-01

Full Text Available O artigo examinou, com base em resoluções e/ou relatórios de contas, os procedimentos adotados pelos Tribunais de Contas do Estado (TCE e dos Municípios (TCM da Bahia para a verificação da receita e despesa vinculada à educação e constatou uma série de omissões, inconsistências e equívocos que muito provavelmente reduziram o montante de recursos legalmente vinculados à educação. O TCE, por exemplo, se limitou à contabilização do percentual mínimo dos impostos e nunca mencionou as receitas adicionais a este mínimo, como o salário-educação, os repasses federais para merenda e outros programas ou operações de crédito vinculadas à educação, significativas no caso da Bahia. Além disso, os relatórios contêm dados discrepantes e confundem gastos na função orçamentária Educação com os realizados em manutenção e desenvolvimento do ensino, dois conceitos diferentes. Também o TCM cometeu muitos equívocos, em suas resoluções, a começar pela terminologia. Empregou 'ensino básico' no lugar de 'educação infantil' e confundiu despesas no ensino (categoria mais ampla com despesas no Fundef (categoria mais restrita. Incorreu em ilegalidade ao aceitar que parte dos 40% dos recursos do Fundef (ou do Fundeb fossem destinados a escolas comunitárias, confessionais ou filantrópicas.El artículo ha examinado, con base en resoluciones y/o informes de cuentas, los procedimientos adoptados por los Tribunales de Cuentas de la Provincia (TCE y de los Municipios (TCM de Bahia para la verificación de los ingresos e despesas vinculadas a educación y ha constatado una serie de omisiones, inconsistencias y equívocos que muy probablemente han reducido el montante de fondos legalmente vinculados a la educación. El TCE, por ejemplo, ha limitado a la contabilización del porcentual mínimo de los impuestos y nunca mencionó los ingresos adicionales a este mínimo, como las transferencias federales para el gobierno provincial y

Comparative study of transparent ceramic and single crystal Ce doped LuAG scintillators

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Kamada, Kei; Yanagida, Satoko; Yoshikawa, Akira; Yagi, Hideki; Yanagitani, Takagimi

2011-01-01

Transparent ceramic Ce 0.5% doped Lu 3 Al 5 O 12 (LuAG) scintillator grown by the sintering method and single crystalline Ce doped LuAG grown by the Czochralski method are prepared. They are cut to the physical dimensions 4 × 4 × 2 mm 3 . Their transmittance and radio luminescence spectra are evaluated. They are both transmissive in wavelength longer than 500 nm and intense Ce 3+ 5d–4f emission appears around 520 nm. When 137 Cs γ-ray is irradiated, 662 keV photo-absorption peaks are clearly observed in each sample. The transparent ceramic one shows higher light yield than that of the single crystalline one. The absolute light yield of the ceramic sample is turned out to be 14800 ± 1500 ph/MeV. The decay time constants are evaluated under pulse X-ray excitation. The main component of the decay time of ceramic and single crystalline one are determined as 37 and 46 ns, respectively.

Structural and luminescence effects of Ga co-doping on Ce-doped yttrium aluminate based phosphors

Energy Technology Data Exchange (ETDEWEB)

Ayvacikli, M. [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Canimoglu, A. [Nigde University, Faculty of Arts and Sciences, Physics Department, Nigde (Turkey); Muresan, L.E., E-mail: laura_muresan2003@yahoo.com [Babes Bolyai University, Raluca Ripan Institute for Research in Chemistry, Fantanele 30, 400294 Cluj-Napoca (Romania); Barbu Tudoran, L. [Babes Bolyai University, Electronic Microscopy Centre, Clinicilor 37, 400006 Cluj Napoca (Romania); Garcia Guinea, J. [Museo Nacional Ciencias Naturales, Jose Gutierrez Abascal 2, Madrid 28006 (Spain); Karabulut, Y. [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Jorge, A. [Museo Nacional Ciencias Naturales, Jose Gutierrez Abascal 2, Madrid 28006 (Spain); Karali, T. [Ege University, Institute of Nuclear Sciences, 35100 Bornova, İzmir (Turkey); Can, N., E-mail: cannurdogan@yahoo.com [Celal Bayar University, Faculty of Arts and Sciences, Department of Physics, Muradiye, Manisa (Turkey); Jazan University, Physics Department, P.O. Box 114, 45142 Jazan (Saudi Arabia)

2016-05-05

Herein, we primarily focus on luminescence spectrum measurements of various types of green emitting yttrium aluminate phosphors modified with gallium (Y{sub 3}Al{sub 5-x}Ga{sub x}O{sub 12}) synthesised by solid state reaction. The luminescent emission of samples depends on sample temperature and excitation radiation such as incident X-ray, electron and laser beam. Here, we measured radioluminescence (RL), cathodoluminescence (CL), photoluminescence (PL) along with XRD in order to clarify relationship between lattice defects and the spectral luminescence emissions. The RL and CL spectra of YAG:Ce exhibit an emission band ranging from 300 to 450 nm related to Y{sub Al} antisite defects. The broad emission band of garnet phosphors is shifted from 526 nm to 498 nm with increasing of Ga{sup 3+} content, while full width at half maximum (FWHM) of the band tends to be greater than the width of unmodified YAG:Ce garnet. Deconvolution of the spectrum reveals that three emission bands centred at 139, 234 and 294 °C occur in aluminate host garnets. - Highlights: • We present preparation of YAG:Ce{sup 3+}, Ga{sup 3+} phosphors by a solid state reaction method. • The shape and size of phosphor particles were investigated. • The luminescence properties were studied by different excitation sources.

The thermal stability and catalytic performance of Ce-Zr promoted Rh-Pd/γ-Al2O3 automotive catalysts

International Nuclear Information System (INIS)

Wu Xiaodong; Xu Luhua; Weng Duan

2004-01-01

The noble metals (Rh, Pd) supported on alumina promoted with Ce-Zr mixed oxides were investigated as catalysts under diverse oxidants/reductants ratios of simulated automotive exhaust feed gas. Aging test was performed in air at 1000 deg. C for 20 h. Both fresh and aged catalysts, as well as alumina-supported Ce-Zr mixed powders, were characterized by means of X-ray diffraction (XRD), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) and X-ray photoelectron spectroscopy (XPS). The results confirmed the oxygen storage capacity of Ce-Zr mixed oxides favored CO, C 3 H 8 and NO conversions in stationary versus dynamic stoichiometric operation. The accelerated aging of the systems produced inconspicuous effect on the phase structure, specific surface area and chemical state of these samples. Accordingly, the aged samples still showed low light-off temperature and broad λ-window, which suggested the relative low relevance of the thermal degradation on the overall catalytic performance of the system

Comparison of Spectral and Scintillation Properties of LuAP:Ce and LuAP:Ce,Sc Single Crystals

Science.gov (United States)

Petrosyan, Ashot G.; Derdzyan, Marina; Ovanesyan, Karine; Shirinyan, Grigori; Lecoq, Paul; Auffray, Etiennette; Kronberger, Matthias; Frisch, Benjamin; Pedrini, Christian; Dujardin, Christophe

2009-10-01

Scintillation properties of LuAP:Ce and LuAP:Ce,Sc crystal series were studied under excitation by gamma-rays from a 137Cs source. Both series demonstrated comparable optical quality in terms of underlying absorption at 260 nm, slope of the optical edge and transmission in the range of emission. The light yield of LuAP:Ce crystals measured in 0.2 cm times 0.2 cm times 0.8 cm pixels increases linearly with the Ce concentration reaching at 0.58 at. % 6448 plusmn 322 ph/MeV and 9911 plusmn 496 ph/MeV in the long and in the short directions respectively (the light yield ratio is 65%) and shows no sign of light saturation. The energy resolution is found to depend, among other factors, on the uniformity of Ce concentration within the pixels and is improved to 7.1 plusmn 0.4% (I = 0.2 cm), 9.5 plusmn 0.5% (I = 0.8 cm). Intentional co-doping with Sc + ions was tested and resulted in increase of the Ce distribution coefficient to about 0.3. This enabled to increase the concentration of Ce in LuAP:Ce,Sc crystals up to 0.7 at. %, while conserving high optical quality. In contrast to LuAP:Ce, the light yield in LuAP:Ce,Sc crystals does not increase with Ce concentration, the photo peak being gradually suppressed. The involved mechanisms are discussed basing on measurements of the unit cell volumes, Ce concentration uniformity, x-ray rocking spectra, absorption spectra of pure and variously doped LuAP crystals, and emission spectra under different excitations.

Formation of Deep Electron Trap by Yb3+ Codoping Leads into Super-Long Persistent Luminescence in Ce3+-doped Yttrium Aluminum Gallium Garnet Phosphors.

Science.gov (United States)

Ueda, Jumpei; Miyano, Shun; Tanabe, Setsuhisa

2018-05-23

The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Cr 3+ compound is one of the brightest persistent phosphors, but its persistent luminescence (PersL) duration is not so long due to the relatively shallow Cr 3+ electron trap. Comparing the vacuum referred binding energy of the electron trapping state by Cr 3+ and those by lanthanide ions, we selected Yb 3+ as a deeper electron trapping center. The Y 3 Al 2 Ga 3 O 12 :Ce 3+ -Yb 3+ phosphors show Ce 3+ :5d→4f green persistent luminescence after ceasing blue light excitation. The formation of Yb 2+ was confirmed by the increased intensity of absorption at 585 nm during the charging process. This result indicates that the Yb 3+ ions act as electron traps by capturing an electron. From the thermoluminescence glow curves, it was found the Yb 3+ trap makes much deeper electron trap with 1.01 eV depth than the Cr 3+ electron trap with 0.81 eV depth. This deeper Yb 3+ trap provides much slower detrapping rate of filled electron traps than the Cr 3+ -codoped persistent phosphor. In addition, by preparing transparent ceramics and optimizing Ce 3+ and Yb 3+ concentrations, the Y 3 Al 2 Ga 3 O 12 :Ce 3+ (0.2%)-Yb 3+ (0.1%) as-made transparent ceramic phosphor showed super long persistent luminescence for over 138.8 hours after ceasing blue light charging.

Estrutura de referência para incubadoras pertencentes a redes de habitats de inovação tecnológica e vinculadas a instituições de ensino

OpenAIRE

Rasoto, Vanessa Ishikawa

2006-01-01

Tese (doutorado) - Universidade Federal de Santa Catarina, Centro Tecnológico. Programa de Pós-Graduação em Engenharia de Produção. A partir do estudo de caso da REPARTE (Rede Paranaense de Incubadoras e Parques Tecnológicos), esta pesquisa construiu uma estrutura de referência de incubadoras pertencentes a redes de habitats de inovação tecnológica vinculadas às instituições de ensino superior (IES). O objetivo desta estrutura de referência é orientar o desenvolvimento de incubadoras atrav...

Radio- and photoluminescence properties of Ce/Tb co-doped glasses with huntite-like composition

Science.gov (United States)

Lorenzi, Roberto; Golubev, Nikita V.; Ziaytdinova, Mariyam Z.; Jarý, Vítězslav; Babin, Vladimir; Malashkevich, Georgii E.; Paleari, Alberto; Sigaev, Vladimir N.; Fasoli, Mauro; Nikl, Martin

2018-04-01

Optical properties of yttria-aluminoborate (YAB) glasses with general composition 10(CexTbyY(1-x-y))-30Al2O3-60B2O3 are investigated and compared with data available on YAB crystals with huntite-like structure. Ce doped samples show optical features ascribable to preferential location of rare earth ions in sites with specific geometry similar to that observed in crystalline structures. Samples prepared with Tb ions as emission activator and Ce ions as sensitizer have been studied within the framework of non-radiative energy transfer. The resulting Förster radius is of 4.6 ± 0.5 Å comparable with that observed in Ce/Tb co-doped YAl3(BO3)4 crystals. The investigated materials possess radio- and photoluminescence emission efficiencies and performances comparable to that of crystalline counterparts with the advantage of having easiness of preparation and workability typical of glassy systems.

Structure and corrosion behavior of sputter deposited cerium oxide based coatings with various thickness on Al 2024-T3 alloy substrates

Energy Technology Data Exchange (ETDEWEB)

Liu, Yuanyuan [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China); Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); Huang, Jiamu, E-mail: huangjiamu@cqu.edu.cn [College of Materials Science and Engineering, Chongqing University, Chongqing 400045 (China); Claypool, James B.; Castano, Carlos E. [Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States); O’Keefe, Matthew J., E-mail: mjokeefe@mst.edu [Materials Research Center, Department of Materials Science and Engineering, Missouri University of Science and Technology, Rolla, MO 65409 (United States)

2015-11-15

Highlights: • Crystalline CeO{sub 2} coatings are deposited on Al 2024-T3 alloys by magnetron sputtering. • The crystal size and internal stress both increased with the thickness of CeO{sub 2} coating. • The ∼210 nm thick coating has the highest adhesion strength to the Al alloy substrate. • The ∼900 nm thick coating increased the corrosion resistance two orders of magnitude. • CeO{sub 2} coatings provide good cathodic inhibition for Al alloys by acting as physical barriers. - Abstract: Cerium oxide based coatings from ∼100 to ∼1400 nm in thickness were deposited onto Al 2024-T3 alloy substrates by magnetron sputtering of a 99.99% pure CeO{sub 2} target. The crystallite size of CeO{sub 2} coatings increased from 15 nm to 46 nm as the coating thickness increased from ∼100 nm to ∼1400 nm. The inhomogeneous lattice strain increased from 0.36% to 0.91% for the ∼100 nm to ∼900 nm thick coatings and slightly decreased to 0.89% for the ∼1400 nm thick coating. The highest adhesion strength to Al alloy substrates was for the ∼210 nm thick coating, due to a continuous film coverage and low internal stress. Electrochemical measurements indicated that sputter deposited crystalline CeO{sub 2} coatings acted as physical barriers that provide good cathodic inhibition for Al alloys in saline solution. The ∼900 nm thick CeO{sub 2} coated sample had the best corrosion performance that increased the corrosion resistance by two orders magnitude and lowered the cathodic current density 30 times compared to bare Al 2024-T3 substrates. The reduced defects and exposed surface, along with suppressed charge mobility, likely accounts for the improved corrosion performance as coating thickness increased from ∼100 nm to ∼900 nm. The corrosion performance decreased for ∼1400 nm thick coatings due in part to an increase in coating defects and porosity along with a decrease in adhesion strength.

CeO2-stabilized tetragonal ZrO2 polycrystals (Ce-TZP ceramics)

International Nuclear Information System (INIS)

Andrade Nono, M.C. de.

1990-12-01

This work presents the development and the characterization of CeO 2 -stabilized tetragonal ZrO 2 polycrystals (Ce-TZP ceramics), since it is considered candidate material for applications as structural high performance ceramics. Sintered ceramics were fabricated from mixtures of powders containing different CeO 2 content prepared by conventional and nonconventional techniques. These powders and their resultant sintered ceramics were specified by chemical and physical characterization, compactation state and mechanical properties. The chemical characteristics were determined by chemical analysis and the physical characteristics were evaluated by phase content, particle and agglomerate size and aspect, and powder porosity. (author)

Magnetic behaviour of new Ce compounds

Energy Technology Data Exchange (ETDEWEB)

Sampathkumaran, E V [Tata Inst. of Fundamental Research, Bombay (India); Mallik, R [Tata Inst. of Fundamental Research, Bombay (India)

1996-07-01

We report initial results of our investigation on the magnetic behaviour of some new Ce compounds. The compounds, CeIr{sub 2}B{sub 2}C and CeIr{sub 2}Ge{sub 2}, do not appear to exhibit bulk magnetic ordering down to 2 K. The alloys, Ce{sub 2}Pd{sub 2}In and Ce{sub 2}Cu{sub 2}In, order magnetically below 4 and 6 K, respectively, and a marginal change in the Pd(Cu)/In composition does not significantly influence the ordering temperatures. (orig.).

Amperometric estimation of La3+ and Ce3+ with cupferron using d.m.e

International Nuclear Information System (INIS)

Pitre, K.S.; Lavale, S.C.

1982-01-01

Cupferron has been employed as a reagent for the amperometric titrations of La 3+ and Ce 3+ in very dilute solution using d.m.e. Hydrochloric acid (pH=2.75) has been used as supporting electrolyte. These titrations revealed cupferron to metal ratio of 1:1. Titrations are not hampered by the presence of a fairly large amount of Li + , Na + , K + , Mg 3+ , Zn 3+ , Al 3+ , Cl - , Br - , I - , NO 3 - , NO 2 - , CH 2 COO - and ClO 4 - ions. Furthermore, micro and ultramicro quantities of La 3+ and Ce 2+ have been successfully determined with an error of less than +- 0.70%. (author)

Chemical durability and resistance to irradiation of LnYSiAlO (Ln=La or Ce) glasses, potential immobilization matrix of minor actinides; Durabilite chimique et comportement a l'irradiation des verres quaternaires LnYSiAlO (Ln = La ou Ce), matrice potentielle d'immobilisation d'actinides mineurs trivalents

Energy Technology Data Exchange (ETDEWEB)

Gavarini, St

2002-11-01

Rare earth aluminosilicate glasses are known for their interesting mechanical and optical properties. Recent studies have shown that their chemical durability was very good too, such they have the potential to be used in the nuclear industry for the specific immobilization of trivalent actinides. Initial dissolution rates of LaYSiAlO and CeYSiAlO were determined using a Soxhlet device (dynamic leaching). The differences linked to the nature of the rare earth element were studied by synthesizing analogous glasses that only differed in their rare earth element composition (%at.): Y-5%, La-5 %, Si-15%, Al-10% O-65%. The influence of pH on the dissolution mechanisms and kinetics was also studied by static leaching tests performed in dilute solutions of NaOH or HNO{sub 3}. Electronic defects and collision cascades, induced by a-disintegration of radioelements confined in storage matrix, can cause important modifications in the glass structure and, thus, influence its chemical durability. To simulate these effects, glass samples were irradiated with {beta} particles and heavy ions accelerated to 2,5 MeV and 200 keV, respectively. Monoliths were then leached in static bi-distilled water (pH{>=}{>=} 5.5) for one month in an autoclave heated to 90 degrees C. Initially, the structural changes caused by irradiation were determined using Raman, NMR and EPR spectroscopies. Ion {mu}-beams, SEM-EDS and XPS analysis were also performed to evaluate the potential modifications of the superficial composition. Finally, the leaching behavior was studied, for both irradiated and unirradiated samples, through solution and solid elementary characterization. (author)

Yb and Er co-doped Y2Ce2O7 nanoparticles: synthesis and ...

Indian Academy of Sciences (India)

much attention due to their potential applications in display .... Figure 1. XRD patterns of Yb3+ and Er3+ co-doped Y2Ce2O7 nanoparticles prepared for 4 h at different sintering .... vels relax to the ground 4I15/2 level (You et al 2012). For.

A study on the growth kinetics of CeO2-modified aluminide coating and its computer fitting

International Nuclear Information System (INIS)

Wen Jiuba; Yang Liusong; Zhu Limin; Zhang Jinmin; Li QuanAn

2009-01-01

A CeO 2 -modified aluminide coating was obtained by composite electro-deposition Ni and CeO 2 particles on 20 steel with different holding time using pack cementation. The growth kinetics curve was given with computer fitting by measuring the thickness of the layer. Scanning electronic microscopy and X-ray energy dispersive spectrometry were used to analyze the microstructure and components of the layer. The results showed that the content of CeO 2 was up to 5.21 wt.% in the rich area of NiAl coatings, which restrain the interdiffusion between the coating and the base during the oxidation process at high temperature. Meanwhile, the growth curve obtained could offer an important basis to forecasting and controlling the depth of the coating

Optical and scintillation properties of Ce-doped LuLiF4 with different Ce concentrations

International Nuclear Information System (INIS)

Yanagida, Takayuki; Fujimoto, Yutaka; Fukuda, Kentaro; Chani, Valery

2013-01-01

The crystals of 0.1, 0.5, and 1 mol% Ce-doped LuLiF 4 (Ce:LLF) grown by the micro-pulling down (μ-PD) method were examined for their optical and scintillation properties. Ce:LLF crystals had ∼80% transparency at wavelengths longer than 300 nm. In photoluminescence spectra, they demonstrated intense emission peaks at 310 and 330 nm with the quantum yield of 60–90%. Ce 3+ 5d–4f emission peaks were also detected at similar wavelengths of 310 and 330 nm in the radioluminescence spectra obtained under X-ray excitation. According to pulse height spectra recorded under γ-ray irradiation, the absolute light yield of Ce 0.1, 0.5, and 1% were 3600±400, 3000±300, and 1700±200 ph/MeV, respectively. Decay time kinetics was also inspected using a pulse X-ray equipped streak camera system. The decay time components of Ce:LLF were ∼70 ns and ∼1 μs for all the samples

Production of 139Ce by the 139La(p,n)139Ce reaction

International Nuclear Information System (INIS)

Ishioka, Noriko S.; Sekine, Toshiaki; Izumo, Mishiroku; Hashimoto, Kazuyuki; Kobayashi, Katsutoshi; Matsuoka, Hiromitsu

2002-01-01

To produce a carrier-free 139 Ce to be used as an efficiency-calibration source for Ge detectors, a target-preparation method and a chemical separation method were studied. It was found that commercially available powders of lanthanum-oxide and lanthanum metal are applicable to a target material in the nuclear reaction 139 La(p,n) 139 Ce. In the separation of 139 Ce from an irradiated lanthanum target, a solvent-extraction method and an ion-exchange method gave final products in good chemical purity. (author)

Effect of yttrium on electron–phonon coupling strength of 5d state of Ce3+ ion in LYSO:Ce crystals

International Nuclear Information System (INIS)

Ding, Dongzhou; Liu, Bo; Wu, Yuntao; Yang, Jianhua; Ren, Guohao; Chen, Junfeng

2014-01-01

This paper aims at an improved understanding of luminescence properties of (Lu 1−x Y x ) 2 SiO 5 :Ce (x=0 at%, 26 at%, 45 at%, 66 at% and 100 at%). Photoluminescence emission and excitation spectra as well as Raman spectra of (Lu 1−x Y x ) 2 SiO 5 :Ce were investigated as a function of yttrium (shortened as Y) content in it. Obtained Huang–Rhys factor S indicates that the coupling between Ce1 (7-oxygen-coordinated), Ce2 (6-oxygen-coordinated) and LYSO lattice is intermediate and strong, respectively. Besides, it was found that: with the increase of Y content, crystal field strength around Ce1 and Ce2 decreases, Stokes shift of Ce1 and Ce2 presents an increase trend, and S of Ce2 tends to decrease. These phenomena were explained by geometrical influence of Y 3+ /Lu 3+ on the crystal field splitting of the 5d levels of Ce 3+ and coupling strength. With the increase of Y content, the evolution of S and coupling energy ħω of Ce1 present a slight increase and decrease trend respectively, while S and coupling energy ħω of Ce2 present an obvious decrease and increase trend, respectively. - Highlights: • Crystal field strength around Ce1 decreases with increase of Y content in LYSO:Ce. • A diagram of Huang–Rhys factor S against Y content in LYSO:Ce was constructed. • A diagram of coupling energy ħω against Y content in LYSO:Ce was constructed. • A diagram of Stokes shift against Y content in LYSO:Ce was constructed

On the origin of the ultraviolet photoluminescence in the Ce.sup.3+./sup.-doped epitaxial films of multicomponent (Lu,Gd).sub.3./sub.(Ga,Al).sub.5./sub.O.sub.12./sub. garnets

Czech Academy of Sciences Publication Activity Database

Babin, Vladimir; Chernenko, K.; Hanus, M.; Krasnikov, A.; Kučera, M.; Nikl, Martin; Zazubovich, S.

2017-01-01

Roč. 254, č. 4 (2017), 1-6, č. článku 1600570. ISSN 0370-1972 R&D Projects: GA ČR GA16-15569S Institutional support: RVO:68378271 Keywords : antisite Ce 3+ centers * fast ultraviolet photoluminescence * (Lu,Gd) sub >3 sub >(Ga,Al) sub >5 sub >O sub >12 sub > garnets Sub ject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 1.674, year: 2016

Thermal neutron imaging with rare-earth-ion-doped LiCaAlF{sub 6} scintillators and a sealed {sup 252}Cf source

Energy Technology Data Exchange (ETDEWEB)

Kawaguchi, Noriaki, E-mail: famicom@mail.tagen.tohoku.ac.jp [Tokuyama Corporation, Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yanagida, Takayuki; Fujimoto, Yutaka; Yokota, Yuui; Kamada, Kei [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Fukuda, Kentaro; Suyama, Toshihisa [Tokuyama Corporation, Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 (Japan); Watanabe, Kenichi; Yamazaki, Atsushi [Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Chani, Valery [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); Yoshikawa, Akira [IMRAM, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Miyagi 980-8577 (Japan); New Industry Creation Hatchery Center, Tohoku University, Sendai 980-8579 (Japan)

2011-10-01

Thermal neutron imaging with Ce-doped LiCaAlF{sub 6} crystals has been performed. The prototype of the neutron imager using a Ce-doped LiCaAlF{sub 6} scintillating crystal and a position sensitive photomultiplier tube (PSPMT) which had 64 multi-channel anode was developed. The Ce-doped LiCaAlF{sub 6} single crystal was grown by the Czochralski method. A plate with dimensions of a diameter of 50x2 mm{sup 2} was cut from the grown crystal, polished, and optically coupled to PSPMT by silicone grease. The {sup 252}Cf source (<1 MBq) was sealed with 43 mm of polyethylene for neutron thermalization. Alphabet-shaped Cd pieces with a thickness of 2 mm were used as a mask for the thermal neutrons. After corrections for the pedestals and gain of each pixel, we successfully obtained two-dimensional neutron images using Ce-doped LiCaAlF{sub 6}.

Effect of Annealing Time of YAG:Ce3+ Phosphor on White Light Chromaticity Values

Science.gov (United States)

Abd, Husnen R.; Hassan, Z.; Ahmed, Naser M.; Almessiere, Munirah Abdullah; Omar, A. F.; Alsultany, Forat H.; Sabah, Fayroz A.; Osman, Ummu Shuhada

2018-02-01

Yttrium and aluminium nitrate phosphors doped with cerium nitrate and mixed with urea (fuel) are prepared by using microwave-induced combustion synthesis according to the formula Y(3-0.06)Al5O12:0.06Ce3+ (YAG:Ce3+) to produce white light emitting diodes by conversion from blue indium gallium nitride-light emitting diode chips. The sintering time with fixed temperature (1050°C) for phosphor powder was optimized and found to be 5 h. The crystallinity, structure, chemical composition, luminescent properties with varying currents densities and chromaticity were characterized by x-ray diffraction, field emission-scanning electron microscopy, transmission electron microscopy, energy dispersive spectroscopy, photoluminescence emission, electroluminescence and standard CIE 1931 chromaticity diagram, respectively. The energy levels of Ce3+ in YAG were discussed based on its absorption and excitation spectra. The results show that the obtained YAG:Ce3+ phosphor sintered for 5 h has good crystallinity with pure phase, low agglomerate with spherical shaped particles and strong yellow emission, offering cool-white LED with tuneable correlated color temperature and a good color rendering index compared to those prepared by sintering for 2 h and as-prepared phosphor powders.

Physico-chemical properties of (U,Ce)O2

International Nuclear Information System (INIS)

Yamada, K.; Yamanaka, S.; Katsura, M.

1998-01-01

The high-temperature X-ray diffraction analysis of (U,Ce)O 2 with CeO 2 contents ranging from 0 to 20 mol.% CeO 2 was performed to obtain the variation of the linear thermal expansion coefficient with the CeO 2 content. Ultrasonic pulse-echo measurements were also carried out from room temperature to 673 K to estimate the change in the mechanical properties of (U,Ce)O 2 with the CeO 2 content. The variation in the linear thermal expansion coefficient at the low CeO 2 content region is more steep than that expected from the linear thermal expansion coefficient of UO 2 and CeO 2 . The Young's and shear moduli of all (U,Ce)O 2 were found to decrease with rising temperature. This was due to the increase of the bond length accompanied by the thermal expansion. Although the lattice parameter decreased with CeO 2 content, the moduli of (U,Ce)O 2 were found to decrease with increasing CeO 2 content at room temperature. These results show that in the range from 0 to 20 mol.% of CeO 2 , as CeO 2 content increases, the bottom of the potential energy in (U,Ce)O 2 is shallower and broader. (orig.)

A comparative investigation of SO2 oxidative transfer over CuO with a CeO2 surface

Science.gov (United States)

Liu, Yifeng; Shen, Benxian; Pi, Zhipeng; Chen, Hua; Zhao, Jigang

2017-04-01

To further improve the catalytic desulfurization function of the Mg-Al spinel sulfur transfer agent in a fluid catalytic cracking (FCC) unit, the reaction paths of SO2 oxidation by O2 over the metal oxide surface of CuO (111) and CeO2 (111) were investigated. In reference to the fact that SO2 reacting with O2 over CuO was a Mars-van Krevelen cycle, a similar reaction law for SO2 oxidation over CeO2 was also verified by characterization methods (e.g., IR, XPS). Meanwhile, the molecular simulation results indicated that the rate-control step of SO2 oxidation over CeO2 (111) and CuO (111) was a SO3 desorption step. The lower energy barrier in the rate-control step corresponded to better catalytic performance; hence, it could explain the reason that CeO2 had a better sulfur oxidization transfer performance than CuO.

Oxygen Vacancies versus Fluorine at CeO 2 (111) : A Case of Mistaken Identity?

NARCIS (Netherlands)

Kullgren, J.; Wolf, M.J.; Castleton, C.W.M.; Mitev, P.; Briels, Willem J.; Hermansson, K.

2014-01-01

We propose a resolution to the puzzle presented by the surface defects observed with STM at the (111) surface facet of CeO 2 single crystals. In the seminal paper of Esch et al. [Science 309, 752 (2005)] they were identified with oxygen vacancies, but the observed behavior of these defects is

Luminescence and defects creation in Ce3+-doped aluminium and lutetium perovskites and garnets

International Nuclear Information System (INIS)

Krasnikov, A.; Savikhina, T.; Zazubovich, S.; Nikl, M.; Mares, J.A.; Blazek, K.; Nejezchleb, K.

2005-01-01

Luminescence, scintillation response, energy transfer and defect creation processes were studied at 4.2-300K for Ce 3+ -doped YAlO 3 , Lu x Y 1-x AlO 3 (x=0.3) and Lu 3 Al 5 O 12 crystals under excitation in the 2.5-11.5eV energy range. Influence of the charge and ionic radius of co-doping ions on the efficiency of these processes, the origin of the defects created and possible mechanisms of their formation were discussed

Comparison between the Oxygen Reduction Reaction Activity of Pd₅Ce and Pt₅Ce

DEFF Research Database (Denmark)

Tripkovic, Vladimir; Zheng, Jian; Rizzi, Gian Andrea

2015-01-01

A set of electrochemical and X-ray spectroscopy measurements have been used conjointly with density functional theory (DFT) simulations to study the activity and stability of Pd5Ce for the oxygen reduction reaction. A polycrystalline Pd5Ce rod has been selected as a model catalyst to test if resu......-Pd5Ce is more facile, requires less atom rearrangement, than transformation from Pt5Ce to Pt3Ce, which might explain the kinetic stability of Pt5Ce at low temperatures....

Free carrier absorption in self-activated PbWO_4 and Ce-doped Y_3(Al_0.25Ga_0.75)_3O_12 and Gd_3Al_2Ga_3O_12 garnet scintillators

OpenAIRE

Auffray, E.; Korjik, M.; M.T. Lucchini; S. Nargelas; O. Sidletskiy; G. Tamulaitis; Y. Tratsiak; A. Vaitkevičius

2016-01-01

Nonequilibrium carrier dynamics in the scintillators prospective for fast timing in high energy physics and medical imaging applications was studied. The time-resolved free carrier absorption investigation was carried out to study the dynamics of nonequilibrium carriers in wide-band-gap scintillation materials: self-activated led tungstate (PbWO_4, PWO) ant two garnet crystals, GAGG:Ce and YAGG:Ce. It was shown that free electrons appear in the conduction band of PWO and YAGG:Ce crystals w...

Ce-doped LuAG single-crystal fibers grown from the melt for high-energy physics

CERN Document Server

Xu, X; Moretti, F; Pauwels, K; Lecoq, P; Auffray, E; Dujardin, C

2014-01-01

Under a stationary stable regime undoped and Ce-doped LuAG (Lu3Al5O12) single-crystal fibers were grown by a micro-pulling-down technique. The meniscus length corresponding to the equilibrium state was <200 mu m. Fluctuations in the fiber composition and pulling rate were found to have a significant effect on the properties of the fibers grown. A great improvement in the performance was found in samples containing low Ce concentrations (<= 0.1 at.\\%) and produced using pulling rates <0.5 mm min(-1). Under such conditions a good lateral surface fiber quality was obtained and light propagation was significantly improved. Conversely, a high Ce concentration and a high pulling rate resulted in a strong degradation of the fiber surface quality causing defects to appear and a decrease in light output. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Dependence of the Ce(iii)/Ce(iv) ratio on intracellular localization in ceria nanoparticles internalized by human cells

KAUST Repository

Ferraro, Daniela

2017-01-09

CeO2 nanoparticles (CNPs) have been investigated as promising antioxidant agents with significant activity in the therapy of diseases involving free radicals or oxidative stress. However, the exact mechanism responsible for CNP activity has not been completely elucidated. In particular, in situ evidence of modification of the oxidative state of CNPs in human cells and their evolution during cell internalization and subsequent intracellular distribution has never been presented. In this study we investigated modification of the Ce(iii)/Ce(iv) ratio following internalization in human cells by X-ray absorption near edge spectroscopy (XANES). From this analysis on cell pellets, we observed that CNPs incubated for 24 h showed a significant increase in Ce(iii). By coupling on individual cells synchrotron micro-X-ray fluorescence (μXRF) with micro-XANES (μXANES) we demonstrated that the Ce(iii)/Ce(iv) ratio is also dependent on CNP intracellular localization. The regions with the highest CNP concentrations, suggested to be endolysosomes by transmission electron microscopy, were characterized by Ce atoms in the Ce(iv) oxidation state, while a higher Ce(iii) content was observed in regions surrounding these areas. These observations suggest that the interaction of CNPs with cells involves a complex mechanism in which different cellular areas play different roles.

Dependence of the Ce(iii)/Ce(iv) ratio on intracellular localization in ceria nanoparticles internalized by human cells

KAUST Repository

Ferraro, Daniela; Tredici, Ilenia G.; Ghigna, Paolo; Castillio-Michel, Hiram; Falqui, Andrea; Di Benedetto, Cristiano; Alberti, Giancarla; Ricci, Vittorio; Anselmi-Tamburini, Umberto; Sommi, Patrizia

2017-01-01

CeO2 nanoparticles (CNPs) have been investigated as promising antioxidant agents with significant activity in the therapy of diseases involving free radicals or oxidative stress. However, the exact mechanism responsible for CNP activity has not been completely elucidated. In particular, in situ evidence of modification of the oxidative state of CNPs in human cells and their evolution during cell internalization and subsequent intracellular distribution has never been presented. In this study we investigated modification of the Ce(iii)/Ce(iv) ratio following internalization in human cells by X-ray absorption near edge spectroscopy (XANES). From this analysis on cell pellets, we observed that CNPs incubated for 24 h showed a significant increase in Ce(iii). By coupling on individual cells synchrotron micro-X-ray fluorescence (μXRF) with micro-XANES (μXANES) we demonstrated that the Ce(iii)/Ce(iv) ratio is also dependent on CNP intracellular localization. The regions with the highest CNP concentrations, suggested to be endolysosomes by transmission electron microscopy, were characterized by Ce atoms in the Ce(iv) oxidation state, while a higher Ce(iii) content was observed in regions surrounding these areas. These observations suggest that the interaction of CNPs with cells involves a complex mechanism in which different cellular areas play different roles.

Influence of Ce 0.68 Zr 0.32 O 2 solid solution on depositing ...

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 29; Issue 1. Influence of Ce0.68Zr0.32O2 solid solution on depositing -alumina washcoat on FeCrAl foils. Mei-Qing Shen Li-Wei Jia Wen-Long Zhou Jun Wang Ying Huang. Composites Volume 29 Issue 1 February 2006 pp 73-76 ...

Electrochemical methods for corrosion testing of Ce-based coating prepared on AA6060 alloy by dip immersion method

Directory of Open Access Journals (Sweden)

Jegdić Bore V.

2013-01-01

Full Text Available Dip-immersion is simple and cost-effective method for the preparation of Ce-based conversion coatings (CeCCs, a promising alternative to the toxic chromate coatings, on the metal substrates. In this work CeCCs were prepared on Al-alloy AA6060 from aqueous solution of cerium chloride at room temperature. Effect of immersion time and post-treatment in phosphate solution on the microstructure and corrosion properties of the coatings was studied. The longer immersion time, the thicker but nonhomogeneous and cracked CeCCs. The post-treatment contributed to the sealing of cracks, as proven by an increase in corrosion resistance compared with as-deposited coatings. CeCCs prepared at longer deposition time and post-treated showed much better corrosion protection than those prepared at short deposition time. A detailed EIS study was undertaken to follow the evolution of corrosion behaviour of CeCCs with time of exposure to aggressive chloride environment (3.5 % NaCl. For the sake of comparison, the EIS properties of bare AA6060 were also investigated. A linear voltammetry was performed to complete the study. Results confirmed a formation of protective CeCCs on AA6060 surface. However, even CeCCs prepared at longer deposition time and post-treated provided a short term protection in aggressive environment, due to the small thickness. [Projekat Ministarstva nauke Republike Srbije, br. III 45019 i br. III 45012

Adduct formation in Ce(IV) thenolytrifluoroacetonate

International Nuclear Information System (INIS)

Anufrieva, S.I.; Polyakova, G.V.; Snezhko, N.I.; Pechurova, N.I.; Martynenko, L.I.; Spitsyn, V.I.

1982-01-01

The literature contains no information on adduct formation in Ce(IV) β-diketonates with additional ligands. Since tetrakis-β-diketonates of Ce(IV) have four six-membered chelate rings, we can suppose that the introduction of an additional monodentate or bidentate ligand into the coordination sphere of Ce(IV) β-diketonates would lead to an increase in the coordination number (CN) of the Ce(IV) to nine or ten. The possibility of realization of such a high CN for Ce(IV) has not been proved; a study of adduct formation by Ce(IV) tetrakis-β-diketonates is thus of theoretical interest. Such an investigation might also be of practical interest, because the introduction of an additional ligand into the coordination sphere of a rare-earth β-diketonate usually increases the solubility of the β-diketonate in nonpolar solvents and increases the volatility of the compound; such a modification of the properties is important for various practical purposes. The aim of our work was to study the possibility of separating solid adducts of Ce(IV) tetrakis-thenoyltrifluoroacetonate with certain oxygen-containing and nitrogen-containing donor monodentate and bidentate ligands, and also to investigate their properties. As the β-diketone we used thenoyltrifluoroacetone (HTTFA), since in a parallel investigation it was found that Ce(TTFA) 4 has a high oxidation-reduction stability

Peculiarities of the intermediate valence state of Ce in CeM2Si2 (M = Fe, Co, Ni) compounds

International Nuclear Information System (INIS)

Koterlyn, M.; Shcherba, I.; Yasnitskii, R.; Koterlyn, G.

2007-01-01

The results of thermoelectric power and the electrical resistivity measurements connected with the intermediate valence (IV) of Ce are presented for the compounds CeM 2 Si 2 (M = Fe, Co, Ni) in the temperature range of 4-800 K. It is shown that CeM 2 Si 2 are Kondo-lattices with the coherence scale T coh ∼ 60-80 K and the so-called single-site Kondo temperature T K ∼ 10 3 K. On the example of CeNi 2 Si 2 we have studied the changes in the structure of density of f states (f-DOS) near the Fermi energy caused by atomic substitutions. The results of structural, transport, magnetic, and Ce L III X-ray absorption spectra measurements in the series Ce 1-x La x Ni 2 Si 2 (0 ≤ x ≤ 0.6), Ce(Ni 1-y Cu y ) 2 Si 2 (0 ≤ y ≤ 0.6) and CeNi 2 (Si 1-z Ge z ) 2 (0 ≤ z ≤ 0.5) are presented. We found that the IV state of Ce in the CeM 2 Si 2 is an evidence of possible opening a wide pseudogap Δ ∼ kT K within the f-DOS structure slightly above the Fermi energy

Surface and bulk 4f-photoemission spectra of CeIn3 and CeSn3

International Nuclear Information System (INIS)

Kim, H.; Tjernberg, O.; Chiaia, G.; Kumigashira, H.; Takahashi, T.; Duo, L.; Sakai, O.; Kasaya, M.; Lindau, I.

1997-01-01

Resonant photoemission spectroscopy was performed on CeIn 3 and CeSn 3 at the 4d-4f and 3d-4f core thresholds. Using the different surface sensitivity between the two photon energies, surface and bulk 4f-photoemission spectra were derived for both compounds. With the noncrossing approximation of the Anderson impurity model, the 4d-4f resonant spectra together with the surface and bulk spectra were self-consistently analyzed to obtain the microscopic parameters such as the 4f-electron energy and the hybridization strength with conduction electrons. The result shows a substantial difference in these parameters between the surface and the bulk, indicating that it is important to take into account the surface effect in analyzing photoemission spectra of Ce compounds. It is also found that the 4f surface core-level shift is different between CeIn 3 and CeSn 3 . copyright 1997 The American Physical Society

Optical and scintillation properties of Ce-doped LuLiF{sub 4} with different Ce concentrations

Energy Technology Data Exchange (ETDEWEB)

Yanagida, Takayuki, E-mail: yanagida@lsse.kyutech.ac.jp [Kyushu Institute of Technology, 2-4 Hibikino, Wakamatsu-ku, Kitakyushu, Fukuoka 808-0196 (Japan); Fujimoto, Yutaka [Kyushu Institute of Technology, 2-4 Hibikino, Wakamatsu-ku, Kitakyushu, Fukuoka 808-0196 (Japan); Fukuda, Kentaro [Tokuyama Corporation, Shibuya 3-chome, Shibuya-ku, Tokyo 150-8383 Japan (Japan); Chani, Valery [Tohoku Univ., 2-1-1 Katahira, Sendai 980-8577 (Japan)

2013-11-21

The crystals of 0.1, 0.5, and 1 mol% Ce-doped LuLiF{sub 4} (Ce:LLF) grown by the micro-pulling down (μ-PD) method were examined for their optical and scintillation properties. Ce:LLF crystals had ∼80% transparency at wavelengths longer than 300 nm. In photoluminescence spectra, they demonstrated intense emission peaks at 310 and 330 nm with the quantum yield of 60–90%. Ce{sup 3+} 5d–4f emission peaks were also detected at similar wavelengths of 310 and 330 nm in the radioluminescence spectra obtained under X-ray excitation. According to pulse height spectra recorded under γ-ray irradiation, the absolute light yield of Ce 0.1, 0.5, and 1% were 3600±400, 3000±300, and 1700±200 ph/MeV, respectively. Decay time kinetics was also inspected using a pulse X-ray equipped streak camera system. The decay time components of Ce:LLF were ∼70 ns and ∼1 μs for all the samples.

The crystal structure of galgenbergite-(Ce), CaCe2(CO3)4•H2O

Science.gov (United States)

Walter, Franz; Bojar, Hans-Peter; Hollerer, Christine E.; Mereiter, Kurt

2013-04-01

Galgenbergite-(Ce) from the type locality, the railroad tunnel Galgenberg between Leoben and St. Michael, Styria, Austria, was investigated. There it occurs in small fissures of an albite-chlorite schist as very thin tabular crystals building rosette-shaped aggregates associated with siderite, ancylite-(Ce), pyrite and calcite. Electron microprobe analyses gave CaO 9.49, Ce2O3 28.95, La2O3 11.70, Nd2O3 11.86, Pr2O3 3.48, CO2 30.00, H2O 3.07, total 98.55 wt.%. CO2 and H2O calculated by stoichiometry. The empirical formula (based on Ca + REE ∑3.0) is C{{a}_{1.00 }}{{( {C{{e}_{1.04 }}L{{a}_{0.42 }}N{{d}_{0.42 }}P{{r}_{0.12 }}} )}_{2.00 }}{{( {C{{O}_3}} )}_4}\\cdot {{H}_2}O , and the simplified formula is CaC{{e}_2}{{( {C{{O}_3}} )}_4}\\cdot {{H}_2}O . According to X-ray single crystal diffraction galgenbergite-(Ce) is triclinic, space group Poverline{1},a=6.3916(5) , b = 6.4005(4), c = 12.3898(9) Å, α = 100.884(4), β = 96.525(4), γ = 100.492(4)°, V = 483.64(6) Å3, Z = 2. The eight strongest lines in the powder X-ray diffraction pattern are [ d calc in Å/( I)/ hkl]: 5.052/(100)/011; 3.011/(70)/0-22; 3.006/(66)/004; 5.899/(59)/-101; 3.900/(51)/1-12; 3.125/(46)/-201; 2.526/(42)/022; 4.694/(38)/-102. The infrared absorption spectrum reveals H2O (OH-stretching mode at 3,489 cm-1, HOH bending mode at 1,607 cm-1) and indicates the presence of distinctly non-equivalent CO3-groups by double and quadruple peaks of their ν1, ν2, ν3 and ν4 modes. The crystal structure of galgenbergite-(Ce) was refined with X-ray single crystal data to R1 = 0.019 for 2,448 unique reflections ( I > 2 σ( I)) and 193 parameters. The three cation sites of the structure Ca(1), Ce(2) and Ce(3) have a modest mixed site occupation by Ca and small amount of REE (Ce, La, Pr, Nd) and vice versa. The structure is based on double layers parallel to (001), which are composed of Ca(1)Ce(2)(CO3)2 single layers with an ordered chessboard like arrangement of Ca and Ce, and with a roof tile

Identidades, poder e incidencia política de organizaciones vinculadas a inmigrantes nicaragüenses en costa rica: aportes teóricos y metodológicos

Directory of Open Access Journals (Sweden)

Francisco Javier Mojica-Mendieta

2007-10-01

Full Text Available Propone desde un enfoque de investigación cualitativo, comprender la relación entre las representaciones sociales de las identidades nacionales y la incidencia de la política de distintas organizaciones vinculadas con inmigrantes nicaragüenses, con el fin de dar insumos tendientes a mejorar la calidad de vida de la población inmigrante en Costa Rica. Abstract The article proposes an approach from the qualitative research standpoint to understand the relationship between the social representations of the national identities and the political incidence of different political organization linked to Nicaraguan inmigrants as bases for the betterment of the inmigrant population in Costa Rica.

Acercamiento al Concepto de Grupos Empresariales: Concurrencia de Elementos para su Existencia

Directory of Open Access Journals (Sweden)

Carlos Mario Montiel Fuentes

2009-06-01

Full Text Available El grupo empresarial es el conjunto de una o más sociedades independientes jurídicamente entre sí, pero que se encuentran bajo un control o subordinación ejercido por una matriz o controlante y sometidas a una dirección unitaria que determina los lineamientos de cada una de ellas. Conformándose el grupo empresarial únicamente cuando concurran los dos elementos de su esencia; 1. El control o subordinación y 2. La unidad de propósito y dirección; sin que signifique esto, que se esté dando nacimiento a un nuevo ente autónomo e independiente, pues se mantiene intacta la personalidad jurídica de cada una de las sociedades vinculadas al grupo.

Novel tunable green-red-emitting oxynitride phosphors co-activated with Ce3+, Tb3+, and Eu3+: photoluminescence and energy transfer.

Science.gov (United States)

Huo, Jiansheng; Dong, Langping; Lü, Wei; Shao, Baiqi; You, Hongpeng

2017-07-14

A series of novel Ce 3+ , Tb 3+ and Eu 3+ ion doped Y 4 SiAlO 8 N-based oxynitride phosphors were synthesized by the solid-state method and characterized by X-ray powder diffraction, scanning electron microscopy, photoluminescence, lifetimes and thermo-luminescence. The excitation of the Ce 3+ /Tb 3+ co-doped and Ce 3+ /Tb 3+ /Eu 3+ tri-doped phosphor with near-UV radiation results in strong linear Tb 3+ green and Eu 3+ red emission. The occurrence of Ce 3+ -Tb 3+ and Ce 3+ -Tb 3+ -Eu 3+ energy transfer processes is responsible for the bright green or red luminescence. The Tb 3+ ion acting as an energy transfer bridge can alleviate MMCT quenching between the Ce 3+ -Eu 3+ ion pairs. The lifetime measurements demonstrated that the energy-transfer mechanisms of Ce 3+ → Tb 3+ and Tb 3+ → Eu 3+ are dipole-quadrupole and quadrupole-quadrupole interactions, respectively. The temperature dependent luminescence measurements showed that as-prepared green/red phosphors have good thermal stability against temperature quenching. The obtained results indicate that these phosphors might serve as promising candidates for n-UV LEDs.

Serviços bibliotecários para dispositivos móveis: O caso das bibliotecas vinculadas ao Conselho Nacional para Assuntos Bibliotecários das Instituições de Educação Superior do México

Directory of Open Access Journals (Sweden)

Eugenia de los Ángeles Ortega Martínez

2016-11-01

Full Text Available Objetivo: Analisar quais são os serviços bibliotecários e as aplicações (apps que se estão utilizando dentro das bibliotecas acadêmicas das Instituições de Educação Superior vinculadas ao Conselho Nacional para Assuntos Bibliotecários das Instituições de Educação Superior (CONPAB-IES, A. C. de México. Método: Foi realizado uma revisão da literatura em bancos de dados e revistas especializadas em Biblioteconomia e Ciências da Informação com ajuda dos recursos digitais da Direção Geral de Bibliotecas da Universidade Nacional Autônoma de México. Resultados e conclusões: O desenvolvimento de apps e serviços bibliotecários dispositivos móveis em bibliotecas acadêmicas das Instituições de Educação Superior,vinculadas ao CONPAB-IES, A. C., mostra uma tendência pelo desenvolvimento de coleções digitais em formatos amigaveis para PC e laptop, a diferença dos smartphones e tablets.

Some regularities of Ce(3) and Ce(4) stabilization in their compounds with β-diketones

International Nuclear Information System (INIS)

Pechurova, N.I.; Martynenko, L.I.; Snezhko, N.I.; Anufrieva, S.I.

1985-01-01

Adduct formation of cerium (3) and cerium (4) β-diketonates (acetylacetonate, benzoylacetonate, dibenzoylmethanate and thenoyltrifluoroacetonate) with oxygen- and nitrogen-donor ligands (Q-α, α'-dipyridyl, o-phenanthroline, trioctylphosphine oxide and triphenylphosphine oxide) is studied. The compounds obtained as a results of the reactions are studied by means of IR-spectroscopic, derivatographic and X-ray phase methods. It is concluded that composition and thermodynamic stability of adducts of Ce(3) tris-β-diketonates are determined by correlation of donor properties of the basis and additional ligand and stability of adducts to oxidation - as well as by their solubility. Introduction of the additional ligand to the system Ce(4)-β-diketones even in the presence of air oxygen stabilizes Ce(3) and destabilizes Ce(4)

Ce decay curves in Ce, Tb co-doped LaF3 and the energy transfer mechanism

International Nuclear Information System (INIS)

Kroon, R.E.; Swart, H.C.; Ntwaeaborwa, O.M.; Seed Ahmed, H.A.A.

2014-01-01

Energy transfer phenomena can play an important role in the development of luminescent materials, and hosts co-doped with Ce 3+ and Tb 3+ ions continue to be actively studied. Several recent reports on Ce, Tb co-doped phosphors suggest different mechanisms for the energy transfer from Ce 3+ to Tb 3+ ions and further study is required to reach consensus on the mechanism or to understand why different mechanisms dominate in different hosts. A more direct method of analysis is proposed to distinguish between the different types of multipole energy transfer mechanisms. When applied to Ce, Tb co-doped LaF 3 , the experimental data shows a poor match to any of these models but is consistent with energy transfer through the exchange mechanism. The decay curves of Ce emission in Ce, Tb co-doped LaF 3 were also studied to obtain further insight on the energy transfer mechanism. Although the decrease in lifetime with increasing Tb concentration shows that energy transfer occurs through a non-radiative mechanism, the form of the decay curves does not correspond to what is expected for energy transfer via multipole interactions.

Homoleptic Ce(III) and Ce(IV) Nitroxide Complexes: Significant Stabilization of the 4+ Oxidation State

Energy Technology Data Exchange (ETDEWEB)

Bogart, Justin A.; Lewis, Andrew J.; Medling, Scott A.; Piro, Nicholas A.; Carroll, Patrick J.; Booth, Corwin H.; Schelter, Eric J.

2014-06-25

Electrochemical experiments performed on the complex Ce-IV[2-((BuNO)-Bu-t)py](4), where [2-((BuNO)-Bu-t)py](-) = N-tert-butyl-N-2-pyridylnitroxide, indicate a 2.51 V stabilization of the 4+ oxidation state of Ce compared to [(Bu4N)-Bu-n](2)[Ce(NO3)(6)] in acetonitrile and a 2.95 V stabilization compared to the standard potential for the ion under aqueous conditions. Density functional theory calculations suggest that this preference for the higher oxidation state is a result of the tetrakis(nitroxide) ligand framework at the Ce cation, which allows for effective electron donation into, and partial covalent overlap with, vacant 4f orbitals with delta symmetry. The results speak to the behavior of CeO2 and related solid solutions in oxygen uptake and transport applications, in particular an inherent local character of bonding that stabilizes the 4+ oxidation state. The results indicate a cerium(IV) complex that has been stabilized to an unprecedented degree through tuning of its ligand-field environment.

Faceting of (001) CeO2 Films: The Road to High Quality TFA-YBa2Cu3O7 Multilayers

International Nuclear Information System (INIS)

Coll, M; Gazquez, J; Sandiumenge, F; Pomar, A; Puig, T; Obradors, X; Espinos, J P; Gonzalez-Elipe, A R

2006-01-01

CeO 2 films are technologically important as a buffer layer for the integration of superconducting YBa 2 Cu 3 O 7 films on biaxially textured Ni substrates. The growth of YBa 2 Cu 3 O 7 layers on the CeO 2 cap layers by the trifluoroacetate (TFA) route remains a critical issue. To improve the accommodation of YBa 2 Cu 3 O 7 on CeO 2 , surface conditioning or CeO 2 is required. In this work we have applied ex-situ post-processes at different atmospheres to the CeO 2 layers deposited on YSZ single crystals using rf sputtering. XPS analysis showed that post-annealing CeO 2 layer in Ar/H 2 /H 2 O catalyses in an unexpected way the growth of (001)- terraces. We also report on the growth conditions of YBa 2 Cu 3 O 7 -TFA on CeO 2 buffered YSZ single crystal grown by chemical solution deposition and we compare them with those leading to optimized YBa 2 Cu 3 O 7 -TFA films on LaAlO 3 single crystals. Critical currents up to 1.6 MA/cm 2 at 77 K have been demonstrated in 300 nm thick YBa 2 Cu 3 O 7 layers on CeO 2 /YSZ system. The optimized processing conditions have then been applied to grow YBa 2 Cu 3 O 7 -TFA films on Ni substrates having vacuum deposited cap layers of CeO 2

Recent approaches in sensitive enantioseparations by CE.

Science.gov (United States)

Sánchez-Hernández, Laura; Castro-Puyana, María; Marina, María Luisa; Crego, Antonio L

2012-01-01

The latest strategies and instrumental improvements for enhancing the detection sensitivity in chiral analysis by CE are reviewed in this work. Following the previous reviews by García-Ruiz et al. (Electrophoresis 2006, 27, 195-212) and Sánchez-Hernández et al. (Electrophoresis 2008, 29, 237-251; Electrophoresis 2010, 31, 28-43), this review includes those papers that were published during the period from June 2009 to May 2011. These works describe the use of offline and online sample treatment techniques, online sample preconcentration techniques based on electrophoretic principles, and alternative detection systems to UV-Vis to increase the detection sensitivity. The application of the above-mentioned strategies, either alone or combined, to improve the sensitivity in the enantiomeric analysis of a broad range of samples, such as pharmaceutical, biological, food and environmental samples, enables to decrease the limits of detection up to 10⁻¹² M. The use of microchips to achieve sensitive chiral separations is also discussed. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The role of Ce(III) in BZ oscillating reactions

Science.gov (United States)

Nogueira, Paulo A.; Varela, Hamilton; Faria, Roberto B.

2012-03-01

Herein we present results on the oscillatory dynamics in the bromate-oxalic acid-acetone-Ce(III)/Ce(IV) system in batch and also in a CSTR. We show that Ce(III) is the necessary reactant to allow the emergence of oscillations. In batch, oscillations occur with Ce(III) and also with Ce(IV), but no induction period is observed with Ce(III). In a CSTR, no oscillations were found using a freshly prepared Ce(IV), but only when the cerium-containing solution was aged, allowing partial conversion of Ce(IV) to Ce(III) by reaction with acetone.

Transition of Emission Colours as a Consequence of Heat-Treatment of Carbon Coated Ce3+-Doped YAG Phosphors

Directory of Open Access Journals (Sweden)

Liang-Jun Yin

2017-10-01

Full Text Available To modify the luminescence properties of Ce3+-doped Y3Al5O12 (YAG phosphors, they have been coated with a carbon layer by chemical vapor deposition and subsequently heat-treated at high temperature under N2 atmosphere. Luminescence of the carbon coated YAG:Ce3+ phosphors has been investigated as a function of heat-treatment at 1500 and 1650 °C. The 540 nm emission intensity of C@YAG:Ce3+ is the highest when heated at 1650 °C, while a blue emission at 400–420 nm is observed when heated at 1500 °C but not at 1650 °C. It is verified by X-ray diffraction (XRD that the intriguing luminescence changes are induced by the formation of new phases in C@YAG:Ce3+-1500 °C, which disappear in C@YAG:Ce3+-1650 °C. In order to understand the mechanisms responsible for the enhancement of YAG:Ce3+ emission and the presence of the blue emission observed for C@YAG:Ce3+-1500 °C, the samples have been investigated by a combination of several electron microscopy techniques, such as HRTEM, SEM-CL, and SEM-EDS. This local and cross-sectional analysis clearly reveals a gradual transformation of phase and morphology in heated C@YAG:Ce3+ phosphors, which is related to a reaction between C and YAG:Ce3+ in N2 atmosphere. Through reaction between the carbon layer and YAG host materials, the emission colour of the phosphors can be modified from yellow, white, and then back to yellow under UV excitation as a function of heat-treatment in N2 atmosphere.

Magnetic behavior of the alloys (Ce{sub 1-x}Y{sub x}){sub 2}PdSi{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Mallik, R [Tata Inst. of Fundamental Res., Colaba, Mumbai (India); Sampathkumaran, E V [Tata Inst. of Fundamental Res., Colaba, Mumbai (India)

1996-11-01

The results of X-ray diffraction (Cu K{sub {alpha}}), electrical resistivity ({rho}), heat capacity (C) and magnetic susceptibility ({chi}) measurements are reported for a new pseudoternary solid solution, (Ce{sub 1-x}Y{sub x}){sub 2}PdSi{sub 3} (x=0.0, 0.2, 0.5, 0.8, 1.0). The X-ray diffraction patterns indicate that single phase alloys can be formed in a derived version of the AlB{sub 2}-type hexagonal structure for x{>=}0.2, while for x=0.0, apparently there is an additional weak phase. In the case of the alloy Ce{sub 2}PdSi{sub 3}, the majority of Ce ions do not exhibit magnetic ordering down to 1.4 K, though magnetic ordering at 7 K from one of the two crystallographically inequivalent sites cannot be ruled out. For other compositions, no magnetic ordering is observed above 1.4 K. The Kondo effect is operative in all these alloys, with the strength of the Kondo effect increasing with the compression of the lattice by the gradual replacement of Ce by Y. The C/T exhibits a low temperature enhancement in all Ce containing alloys. (orig.).

Promoting effect of CeO 2 on cyclohexanol conversion over CeO 2