WorldWideScience

Sample records for air entrainment admixtures

  1. The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

    2010-01-01

    Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...... adsorption capacity based on measurements on a carbon black. The NOx formation increased by up to three times with more oxidizing conditions and thus, there was a trade-off between the AEA requirements of the ash and NOx formation. The type of fuel had high impact on the AEA adsorption behavior of the ash...

  2. Effect of air entraining admixture on mechanical properties and durability of coarse porous concrete%引气剂对大孔混凝土力学性能及耐久性的影响

    Institute of Scientific and Technical Information of China (English)

    张蔚

    2012-01-01

    The addition of air entraining admixture could improve durability of ordinary concrete effectively, while the effect on coarse porous concrete is not obvious. The article describe the reseach on the effect of air entraining admixture on mechanical properties and durability of coarse porous con- crete. The result shows that the compressive strength and resistance properties to freeze--thaw could be improved with the appropriate amount of air entraining admixture by testing.%引气剂能有效改善普通混凝土的耐久性.但对大孔混凝土性能的影响不明确。本文通过试验,研究不同掺量引气剂对大孔混凝土力学性能及耐久性能的影响。结果表明,适量的引气剂能够增强大孔混凝土的抗压强度和改善抗冻性能。

  3. Local air entrainment and detrainment

    OpenAIRE

    Kobus, Helmut

    1984-01-01

    Air and water are usually well separated by gravity due to their extreme difference in specific weight. Whenever they are mixed, however, they give rise to a very complex two-phase flow situation. The hydraulic engineer is often faced with the problem of estimating the effects of entrained air upon the flow, because this may be essential for the safe operation of a hydraulic structure.The predominant mechanism in generating airwater mixtures is the inclusion of air at the surface of flowing w...

  4. EFFECTS OF ENTRAINED AIR MANNER ON CAVITATION DAMAGE*

    Institute of Scientific and Technical Information of China (English)

    WU Jian-hua; LUO Chao

    2011-01-01

    Early in 1953 the experiments by Peterka proved that air entrainment has effects on decreasing cavitation damage. This technology has been widely used in the release works of high dams since the inception of air entrainment in the Grand Goulee Dam in 1960. Behavior, mechanism and application of air entrainment for cavitation damage control have been investigated for over half century. However, severe cavitation damage happened due to complex mechanism of air entrainment. The effects of air entrainment are related to many factors, including geometric parameters, hydraulic parameters and entrained air manners. In the present work an experimental set-up for air entrainment was specially designed, the behavior of reducing cavitation damage was experimentally investigated in the three aspects of entrained air pressure, air tube aera and air tube number. The results show that magnitude of reduction of cavitation damage is closely related to the entrained air tube number as well as entrained air pressure, air tube aera, and that the effect through three air tubes is larger than that through single air tube although the entrained air tubes have the same sum of tube aera, that is, 1 + 1 + 1 > 3. Therefore, it is important to design an effective manner of air entrainment.

  5. Air entrainment through free-surface cusps

    CERN Document Server

    Eggers, J

    2000-01-01

    In many industrial processes, such as pouring a liquid or coating a rotating cylinder, air bubbles are entrapped inside the liquid. We propose a novel mechanism for this phenomenon, based on the instability of cusp singularities that generically form on free surfaces. The air being drawn into the narrow space inside the cusp destroys its stationary shape when the walls of the cusp come too close. Instead, a sheet emanates from the cusp's tip, through which air is entrained. Our analytical theory of this instability is confirmed by experimental observation and quantitative comparison with numerical simulations of the flow equations.

  6. Measurement of air entrainment in plasma jets

    International Nuclear Information System (INIS)

    The concentration and temperature of air entrained into argon and helium plasma jets has been measured using coherent anti-Stokes Raman spectroscopy (CARS). The argon plasma flow field is characterized by a short region of well behaved laminar flow near the nozzle exit followed by an abrupt transition to turbulence. Once the transition of turbulence occurs, air is rapidly mixed into the jet core. The location of the transition region is determined by the rapid cooling of the jet and the resulting increase in Reynolds number. In contrast, the helium plasma flow field never exceeds a Reynolds number of 200 and remains laminar. The entrainment process in this case is controlled by molecular diffusion rather than turbulent mixing. 9 refs., 5 figs., 1 tab

  7. Entrainment Rate in Shallow Cumuli: Dependence on Entrained Dry Air Sources and Probability Density Functions

    Science.gov (United States)

    Lu, C.; Liu, Y.; Niu, S.; Vogelmann, A. M.

    2012-12-01

    In situ aircraft cumulus observations from the RACORO field campaign are used to estimate entrainment rate for individual clouds using a recently developed mixing fraction approach. The entrainment rate is computed based on the observed state of the cloud core and the state of the air that is laterally mixed into the cloud at its edge. The computed entrainment rate decreases when the air is entrained from increasing distance from the cloud core edge; this is because the air farther away from cloud edge is drier than the neighboring air that is within the humid shells around cumulus clouds. Probability density functions of entrainment rate are well fitted by lognormal distributions at different heights above cloud base for different dry air sources (i.e., different source distances from the cloud core edge). Such lognormal distribution functions are appropriate for inclusion into future entrainment rate parameterization in large scale models. To the authors' knowledge, this is the first time that probability density functions of entrainment rate have been obtained in shallow cumulus clouds based on in situ observations. The reason for the wide spread of entrainment rate is that the observed clouds are affected by entrainment mixing processes to different extents, which is verified by the relationships between the entrainment rate and cloud microphysics/dynamics. The entrainment rate is negatively correlated with liquid water content and cloud droplet number concentration due to the dilution and evaporation in entrainment mixing processes. The entrainment rate is positively correlated with relative dispersion (i.e., ratio of standard deviation to mean value) of liquid water content and droplet size distributions, consistent with the theoretical expectation that entrainment mixing processes are responsible for microphysics fluctuations and spectral broadening. The entrainment rate is negatively correlated with vertical velocity and dissipation rate because entrainment

  8. Dry Air Entrainment into Hurricane Earl

    Science.gov (United States)

    Guillory, Anthony R.; Jedlovec, Gary J.; Atkinson, Robert J.; Hood, Robbie E.; LaFontaine, Frank J.

    2000-01-01

    Hurricane Earl formed in the Gulf of Mexico in September 1998. It quickly was upgraded from a tropical disturbance to tropical storm status and then to a hurricane. Earl possessed hybrid (tropical and extratropical) characteristics throughout its lifetime. The system maintained and erratic track, which led to wide variability in the operational track forecasts. It eventually made landfall on the Florida panhandle on 2 September and raced northeastward. During August and September 1998, NASA conducted the third Convection and Moisture Experiment (CAMEX-3). The experiment was focused on studying hurricanes with an emphasis toward developing a better understanding of their intensification and motion. Earl provides a unique opportunity to utilize high spatial and temporal resolution data collected from the DC-8 and high altitude ER-2 NASA platforms, which flew over Earl as it made landfall. These data can also be put into broader view provided by other instruments from the Geosychronous Operational Environmental Satellites (GOES) and the Tropical Rainfall Measuring Mission (TRMM) satellites. Hurricane Earl was affected by entrainment of dry air from the northwest. Hurricane Isis was intensifying and approaching the Mexican Pacific coast with its associated outflow potentially affecting the inflow into Earl as the storm neared Florida. In addition, a longwave synoptic trough circulation was present over the eastern U.S. Either or both of these could be responsible for the dry air into the system. This paper will focus on identifying the source of the dry by using upper-level wind and moisture fields derived from the GOES 6.7 um water vapor imagery. We will attempt to relate the large-scale observations to those from the NASA aircraft. An infrared instrument onboard the ER-2 also has a similar wavelength and may be able to confirm some of the GOES findings. In addition, a microwave radiometer with 4 channels focused on measuring precipitation and its associated ice

  9. On air entrainment into water in an overflow piping

    International Nuclear Information System (INIS)

    An experimental study was made of air entrainment into water flowing downwards in a vertical pipe. The static pressure distributions along the pipe axis and the velocity distributions in a water layer formed on the wall of pipe were precisely measured to examine the behaviors of flows and air entrainment. The amount of air entrained through the water passage was also measured at the exit of the pipe, as the water flow rate was varied. Moreover, flow visualization was conducted to ascertain flow patterns in the pipe. The results obtained indicate that, with steady overflow being maintained, such flows as annular, mixing and bubbly flows are observed along a pipeline. Air entrainment takes place predominantly in annular flows adjacent to the wall of the pipe. (author)

  10. Air entrainment by plunging water jets

    NARCIS (Netherlands)

    Van de Sande, E.

    1974-01-01

    Gas entrainment caused by the impact of liquid jets upon liquid pool surfaces is a subject which has received too little attention. This well-known phenomenon,which occurs In nature and in numerous industrial operations, has only recently received interest from scientific workers. The influence on p

  11. Entrainment of Air into Vertical Jets in a Crosswind

    Science.gov (United States)

    Roberts, K. K.; Solovitz, S.; Freedland, G.; Camp, E.; Cal, R. B.; Mastin, L. G.

    2015-12-01

    During volcanic eruptions, ash concentration must be determined for aviation safety, but the limiting threshold is difficult to distinguish visually. Computational models are typically used to predict ash concentrations, using inputs such as plume height, eruptive duration, and wind speeds. The models also depend on empirical parameters, such as the entrainment of atmospheric air as a ratio of the air inflow speed and the jet speed. Entrainment of atmospheric air plays a critical role in the behavior of volcanic plumes in the atmosphere, impacting the mass flow rate, buoyancy, and particle concentration of the plume. This process is more complex in a crosswind, leading to greater uncertainty in the model results. To address these issues, a laboratory-scale study has been conducted to improve the entrainment models. Observations of a vertical, unconfined jet are performed using Particle Image Velocimetry, while varying jet density using different compressed gases and Reynolds number. To test the effects of a crosswind on plume entrainment rates, these are then compared with similar jet experiments in a wind tunnel. A series of jet geometries, jet speeds and tunnel speeds are considered. The measured velocities are used to determine the entrainment response, which can be used to determine ash concentration over time as atmospheric air is entrained into the plume. We also quantify the mean and the fluctuations in flow velocity.

  12. Modification of the cast concrete mixture by air-entraining agents

    Directory of Open Access Journals (Sweden)

    N.I. Vatin

    2015-06-01

    Full Text Available The paper investigates the combined effect of superplasticizer based on the naphthalene lignosulfonate and the air-entraining surfactant agent on the fluidity, connectivity and air entrainment of concrete. The air-entraining surfactant agent contributes significantly into air entrainment and reduces the water gain and the mortar separation. It was found that under the introduction of air-entraining surfactant agents in the concrete mixture which contains the superplasticizer, the concrete mobility decreases even though the air-entraining agent is a plasticizer itself. The introduction of 0.1 % air-entraining agent decreases mobility: slump Abrams – 5–6 %, slump flow – 18–22 %. Besides, the effect of increasing the connectivity of the concrete mix is associated with the air entrainment. Regardless of the air-entraining surfactant agent, the superplasticizer reduces water separation, and does not have an air-entraining impact, and virtually has no effect on the air entrainment caused by the addition of the air-entraining agent. With the increasing quantity of the air-entraining surfactant agent in the concrete mix, regardless of the superplasticizer dosage, the amount of the entrained air increases from 3 to 7 %, and water separation is reduced to almost 0. Thus, the synergy of the superplasticizer and the air-entraining agent was negative, but it is possible to observe a positive effect in respect of the concrete mix connectivity.

  13. A new technology for air-entrainment of concrete

    DEFF Research Database (Denmark)

    Laustsen, Sara; Hasholt, Marianne Tange; Jensen, Ole Mejlhede

    This paper describes a new technology for air-entrainment of concrete. The technology is based on the addition of dry superabsorbent polymers (SAP) to the concrete. A large amount of small internal water reservoirs are formed during mixing when SAP absorbs water and swells. The internal water...... reservoirs are distributed throughout the concrete. During the hydration process the cement paste imbibes water from the water-filled SAP voids. Thereby the water-filled SAP voids turn into partly air-filled voids. The advantages of the SAP-based technology compared to traditional chemical air-entrainment...

  14. Air entrainment into annular water flows in a vertical pipe

    International Nuclear Information System (INIS)

    An experimental investigation was carried out on air entrainment into water flowing downward in a vertical pipe. Local flow rates of water and air in a fluid layer of annular flow, formed on the pipe wall, were measured precisely by using a small tube probe. Measurements were also made of local flow rates of water and air in bubbly flow downstream of annular water flow. Distributions of local flow rates in the radial direction of the pipe for annular flow regime indicate that the fluid layer consists of a water layer adjacent to the pipe wall and a water-air (two-phase fluid) layer located inside of the water layer. The water-air layer is formed as a result of air entrainment. The departure of air bubbles from a water pool to air phase was found for bubbly flow regime. (author)

  15. Universal mechanism for air entrainment during liquid impact

    Science.gov (United States)

    Hendrix, Maurice H. W.; Bouwhuis, Wilco; van der Meer, Devaraj; Lohse, Detlef; Snoeijer, Jacco H.

    2016-02-01

    When a mm-sized liquid drop approaches a deep liquid pool, both the interface of the drop and the pool deform before the drop touches the pool. The build up of air pressure prior to coalescence is responsible for this deformation. Due to this deformation, air can be entrained at the bottom of the drop during the impact. We quantify the amount of entrained air numerically, using the Boundary Integral Method (BIM) for potential flow for the drop and the pool, coupled to viscous lubrication theory for the air film that has to be squeezed out during impact. We compare our results to various experimental data and find excellent agreement for the amount of air that is entrapped during impact onto a pool. Next, the impact of a rigid sphere onto a pool is numerically investigated and the air that is entrapped in this case also matches with available experimental data. In both cases of drop and sphere impact onto a pool the numerical air bubble volume V_b is found to be in agreement with the theoretical scaling V_b/V_{drop/sphere} ~ St^{-4/3}, where St is the Stokes number. This is the same scaling that has been found for drop impact onto a solid surface in previous research. This implies a universal mechanism for air entrainment for these different impact scenarios, which has been suggested in recent experimental work, but is now further elucidated with numerical results.

  16. Dispersal and air entrainment in unconfined dilute pyroclastic density currents

    Science.gov (United States)

    Andrews, Benjamin J.

    2014-09-01

    Unconfined scaled laboratory experiments show that 3D structures control the behavior of dilute pyroclastic density currents (PDCs) during and after liftoff. Experiments comprise heated and ambient temperature 20 μm talc powder turbulently suspended in air to form density currents within an unobstructed 8.5 × 6 × 2.6-m chamber. Comparisons of Richardson, thermal Richardson, Froude, Stokes, and settling numbers and buoyant thermal to kinetic energy densities show good agreement between experimental currents and dilute PDCs. The experimental Reynolds numbers are lower than those of PDCs, but the experiments are fully turbulent; thus, the large-scale dynamics are similar between the two systems. High-frequency, simultaneous observation in three orthogonal planes shows that the currents behave very differently than previous 2D (i.e., confined) currents. Specifically, whereas ambient temperature currents show radial dispersal patterns, buoyancy reversal, and liftoff of heated currents focuses dispersal along narrow axes beneath the rising plumes. The aspect ratios, defined as the current length divided by a characteristic width, are typically 2.5-3.5 in heated currents and 1.5-2.5 in ambient temperature currents, reflecting differences in dispersal between the two types of currents. Mechanisms of air entrainment differ greatly between the two currents: entrainment occurs primarily behind the heads and through the upper margins of ambient temperature currents, but heated currents entrain air through their lateral margins. That lateral entrainment is much more efficient than the vertical entrainment, >0.5 compared to ˜0.1, where entrainment is defined as the ratio of cross-stream to streamwise velocity. These experiments suggest that generation of coignimbrite plumes should focus PDCs along narrow transport axes, resulting in elongate rather than radial deposits.

  17. Entrainment.

    Science.gov (United States)

    Carrier, Romance F.

    1978-01-01

    Presents a literature review including: (1) theoretical studies concerned with the development of methdology to determine the significance of entrainment effects to whale populations and ecosystems; and (2) site and laboratory studies. A list of 107 references drawn from the 1976 and 1977 literature is also presented. (HM)

  18. Freeze-Thaw Durability of Air-Entrained Concrete

    OpenAIRE

    Huai-Shuai Shang; Ting-Hua Yi

    2013-01-01

    One of the most damaging actions affecting concrete is the abrupt temperature change (freeze-thaw cycles). The types of deterioration of concrete structures by cyclic freeze-thaw can be largely classified into surface scaling (characterized by the weight loss) and internal crack growth (characterized by the loss of dynamic modulus of elasticity). The present study explored the durability of concrete made with air-entraining agent subjected to 0, 100, 200, 300, and 400 cycles of freeze-thaw. T...

  19. Universal mechanism for air entrainment during liquid impact

    CERN Document Server

    Hendrix, Maurice H W; van der Meer, Devaraj; Lohse, Detlef; Snoeijer, Jacco H

    2015-01-01

    When a mm-sized liquid drop approaches a deep liquid pool, both the interface of the drop and the pool deform before the drop touches the pool. The build up of air pressure prior to coalescence is responsible for this deformation. Due to this deformation, air can be entrained at the bottom of the drop during the impact. We quantify the amount of entrained air numerically, using the Boundary Integral Method (BIM) for potential flow for the drop and the pool, coupled to viscous lubrication theory for the air film that has to be squeezed out during impact. We compare our results to various experimental data and find excellent agreement for the amount of air that is entrapped during impact onto a pool. Next, the impact of a rigid sphere onto a pool is numerically investigated and the air that is entrapped in this case also matches with available experimental data. In both cases of drop and sphere impact onto a pool the numerical air bubble volume V_b is found to be in agreement with the theoretical scaling V_b/V_...

  20. Freeze-thaw durability of air-entrained concrete.

    Science.gov (United States)

    Shang, Huai-Shuai; Yi, Ting-Hua

    2013-01-01

    One of the most damaging actions affecting concrete is the abrupt temperature change (freeze-thaw cycles). The types of deterioration of concrete structures by cyclic freeze-thaw can be largely classified into surface scaling (characterized by the weight loss) and internal crack growth (characterized by the loss of dynamic modulus of elasticity). The present study explored the durability of concrete made with air-entraining agent subjected to 0, 100, 200, 300, and 400 cycles of freeze-thaw. The experimental study of C20, C25, C30, C40, and C50 air-entrained concrete specimens was completed according to "the test method of long-term and durability on ordinary concrete" GB/T 50082-2009. The dynamic modulus of elasticity and weight loss of specimens were measured after different cycles of freeze-thaw. The influence of freeze-thaw cycles on the relative dynamic modulus of elasticity and weight loss was analyzed. The findings showed that the dynamic modulus of elasticity and weight decreased as the freeze-thaw cycles were repeated. They revealed that the C30, C40, and C50 air-entrained concrete was still durable after 300 cycles of freeze-thaw according to the experimental results. PMID:23576906

  1. Freeze-Thaw Durability of Air-Entrained Concrete

    Directory of Open Access Journals (Sweden)

    Huai-Shuai Shang

    2013-01-01

    Full Text Available One of the most damaging actions affecting concrete is the abrupt temperature change (freeze-thaw cycles. The types of deterioration of concrete structures by cyclic freeze-thaw can be largely classified into surface scaling (characterized by the weight loss and internal crack growth (characterized by the loss of dynamic modulus of elasticity. The present study explored the durability of concrete made with air-entraining agent subjected to 0, 100, 200, 300, and 400 cycles of freeze-thaw. The experimental study of C20, C25, C30, C40, and C50 air-entrained concrete specimens was completed according to “the test method of long-term and durability on ordinary concrete” GB/T 50082-2009. The dynamic modulus of elasticity and weight loss of specimens were measured after different cycles of freeze-thaw. The influence of freeze-thaw cycles on the relative dynamic modulus of elasticity and weight loss was analyzed. The findings showed that the dynamic modulus of elasticity and weight decreased as the freeze-thaw cycles were repeated. They revealed that the C30, C40, and C50 air-entrained concrete was still durable after 300 cycles of freeze-thaw according to the experimental results.

  2. Air entrainment and the dynamics of volcanic jets and plumes

    Science.gov (United States)

    Mastin, L. G.; Solovitz, S.

    2008-12-01

    During a typical pyroclastic eruption, gas and pyroclasts exit a volcanic vent at speeds of tens to hundreds of meters per second. At the vent the mixture is negatively buoyant, and rises as a plinian column only if it ingests and heats sufficient air to attain positive buoyancy. As erosion increases vent radius r during an eruption, eruptive mass flux increases with r2, but the mass of air entrained increases only with r1. Hence the column ingests progressively less air relative to its mass and eventually, at some threshold mass flux m, collapses. The threshold mass flux m depends strongly on the air entrainment coefficient ɛ, i.e. the velocity of inrushing air normalized to the upward jet velocity. The value of ɛ is not well characterized in the near-vent region, and likely varies with vent geometry, overpressure, and jet density among other factors. Theoretical scaling relations suggest that a two-fold variation in ɛ (e.g. 0.05-0.10) results in a four-fold variation in m. Numerical models of overpressured jets show that near- vent entrainment may be inhibited by shock waves, promoting partial or oscillatory column collapse within an otherwise steady plinian column. Here we present the first results of laboratory experiments using particle image velocimetry to quantify near-vent air entrainment. In these experiments, we use a jet of compressed air seeded with 3 μm TiO2 tracer particles, exiting a vertically-directed pipe 1.27 cm in inside diameter and 18 cm long, with upstream pressures of 0 to 21 kPa, producing a pressure-balanced jet at the exit with velocities up to about 180 m s-1. The ambient air was seeded with tracer oil droplets a few micrometers in diameter from a fog machine. The seeded jet was illuminated by a 0.5 mm-thick Nd:YAG laser sheet that extended 5 cm above and horizontally from the vent. Particles illuminated by this sheet were photographed by pairs of images separated in time by 10 to 200 μs, from which we were able to extract flow

  3. Effect of the Entrained Air Void on Strength and Interfacial Transition Zone of Air-Entrained Mortar

    Institute of Scientific and Technical Information of China (English)

    GAO Hui; ZHANG Xiong; ZHANG Yongjuan

    2015-01-01

    In order to facilitate the development and application of air entraining agents (AEA) in the high performance concrete, entrained air void structure parameters (air void size range from 10 to 1 600 μm) of 28 d sifted mortar were measured by image analysis method. The relationship between the air void size distribution and strength of mortar was studied by methods of grey connection analysis and multiple linear regression analysis. The multiple linear regression equation was established with a correlation coefifcient of 0.966. The weight of the affection of hierarchical porosity on the compressive strength ratio was also obtained. In addition, the effect of air voids on the paste-aggregate interfacial transition zone (ITZ) was analyzed by microhardness. The results show that the correlation between different pore size range and the compressive strength is negative. The effect of air void size distribution on 28 days compressive strength is different: under the condition of similar total porosity, with the increase of the porosity of the air void size, ranging from 10 to 200 μm, and the decrease of the porosity, ranging from 200 to 1 600 μm, the average air void diameter and mean free spacing are decreased; as well as the width of ITZ. On the contrary, the microhardness of the ITZ is increased while the compressive strength loss is decreased.

  4. The Influence of Admixtures on the Technological Properties of Fresh Concrete Mixture

    OpenAIRE

    Albertas KLOVAS; Daukšys, Mindaugas

    2015-01-01

    In this research superplasticizing (SP), air voids removing (AVR), viscosity modifying (VM) and air entraining admixtures (AE) were used. The dosage of admixtures was chosen from minimum to maximum values recommended by the manufacturers. To sum up, 7 concrete mixture compositions with SP, 6 with AVR and 6 with VM and the last 6 with AE admixture were prepared. Water and cement ratio for all the compositions was kept at the same value. According to the results obtained, the usage of SP admixt...

  5. Air entrainment phenomena in hydraulic structures of Electric Power Plants and the related problems

    International Nuclear Information System (INIS)

    Air entrainment phenomena often occur in hydraulic structures of electric power plants, possibly causing some operational problems. For example, air-entraining vortices in pump sumps could induce vibration and noise, while foam is generated in weirs of cooling water channel systems and is discharged into sea. As a result, seascape gets worse and foam often adheres to fishing net. Air-entraining vortices produce bubbles at inlets of a hydro power plant. These bubbles can be accumulated at some places, which could increase loss of channel and induce air hammer phenomena and vibration of pump. A large amount of air entrained in spillway of a hydro power plant can also induce self-priming phenomena or air hammer phenomena. This paper introduces these air entrainment phenomena and the related problems, with showing the related future subjects. (author)

  6. Experimental Study on Durability Improvement of Fly Ash Concrete with Durability Improving Admixture

    OpenAIRE

    Quan, Hong-zhu; Kasami, Hideo

    2014-01-01

    In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete,...

  7. Entrainment of Upper Level Dry Air into Hurricane Earl

    Science.gov (United States)

    Guillory, Anthony R.; Jedlovee, Gary J.; Hood, Robbie E.; Atkinson, Robert J.; LaFontaine, Frank J.

    2000-01-01

    Hurricane Earl developed from a tropical wave that moved into the Gulf of Mexico, which triggered abundant convection. On 1 Sept. 1998, the wave was upgraded directly to a tropical storm. Earl reached hurricane status the next morning. The system moved erratically as it interacted with an upper level short wave trough rotating around a long wave trough to the northeast. The storm made landfall near 0600 UTC on 3 September near Panama City, FL. During August and September 1998, NASA conducted the Third Convection and Moisture Experiment (CAMEX-3). It focused on studying the intensity, track, and impacts at landfall of hurricanes. On the afternoon of 2 September 1998, the NASA ER2 high-altitude aircraft flying at 65,000 feet in tandem with the NASA DC-8 flying at 35,000 feet flew over and through, respectively, the eastern rainbands of Earl near the Florida Panhandle as the storm neared landfall in the region. Two approaches to studying Earl are undertaken here: first, an examination of the source and height of the dry air region using GOES-8 water vapor data and, second, a look into the impact of the dry air entrainment on the system using aircraft remote sensing data.

  8. Development of a New Type of Green Switch Air Entraining Agent for Wet-Mix Shotcrete and Its Engineering Application

    Directory of Open Access Journals (Sweden)

    Guoming Liu

    2016-01-01

    Full Text Available Air entraining agent (AEA can bring a lot of microbubbles into fresh concrete for improving its fluidity; however, high fluidity has adverse effect on the shootability of wet-mix shotcrete. In order to solve the contradictory issue, the paper developed a new type of green switch air entraining agent (GSAE that can improve both the pumpability and shootability. The single-admixture and combination tests containing foaming ability and surface tension were performed with Deer agitator and automatic tension meter. The new AEA was developed with two constituents A and B. A was prepared with Sapindus mukorossi(S-1, dodecyl trimethyl ammonium chloride(1231, and polyacrylamide. B was prepared with lauryl sodium sulfate (K12 and silicone oil. The mass mix proportion was S-1 : 1231 : polyacrylamide : K12 : silicone oil = 1 : 0.33 : 0.2 : 0.33 : 0.47. The application method of GSAE proposed that A was premixed with fresh concrete and then B was added at nozzle. Experimental investigation showed that the optimal mixing amount of GSAE was 0.1%–0.2% relative to cement. All performance measured of wet-mix shotcrete with 0.12% GSAE met the first-grade product requirements of the China National Standard. Compared with the conventional type of AEA, the proposed GSAE is capable of effectively improving pumpability and shootability.

  9. Effect of Fast Freeze-Thaw Cycles on Mechanical Properties of Ordinary-Air-Entrained Concrete

    OpenAIRE

    Huai-shuai Shang; Wei-qun Cao; Bin Wang

    2014-01-01

    Freezing-thawing resistance is a very significant characteristic for concrete in severe environment (such as cold region with the lowest temperature below 0°C). In this study, ordinary-air-entrained (O-A-E) concrete was produced in a laboratory environment; the compressive strength, cubic compressive strength of C50, C40, C30, C25, and C20 ordinary-air-entrained concrete, tensile strength, and cleavage strength of C30 ordinary-air-entrained concrete were measured after fast freeze-thaw cycles...

  10. Air Entrainment in Dynamic Wetting: Knudsen Effects and the Influence of Ambient Air Pressure

    CERN Document Server

    Sprittles, James E

    2015-01-01

    Recent experiments on coating flows and liquid drop impact both demonstrate that wetting failures caused by air entrainment can be suppressed by reducing the ambient gas pressure. Here, it is shown that non-equilibrium effects in the gas can account for this behaviour, with ambient pressure reductions increasing the gas' mean free path and hence the Knudsen number $Kn$. These effects first manifest themselves through Maxwell slip at the gas' boundaries so that for sufficiently small $Kn$ they can be incorporated into a continuum model for dynamic wetting flows. The resulting mathematical model contains flow structures on the nano-, micro- and milli-metre scales and is implemented into a computational platform developed specifically for such multiscale phenomena. The coating flow geometry is used to show that for a fixed gas-liquid-solid system (a) the increased Maxwell slip at reduced pressures can substantially delay air entrainment, i.e. increase the `maximum speed of wetting', (b) unbounded maximum speeds ...

  11. Modeling of Kinetics of Air Entrainment in Water Produced by Vertically Falling Water Flow

    Directory of Open Access Journals (Sweden)

    Adelė VAIDELIENĖ

    2014-09-01

    Full Text Available This study analyzes the process of air entrainment in water caused by vertically falling water flow in the free water surface. The new kinetic model of air entrainment in water was developed. This model includes the process of air entrapment, as well as air removal, water sputtering and resorption. For the experimental part of this study a new method based on digital image processing was developed. Theoretical and experimental methods were used for determining air concentration and its distribution in water below the air-water interface. A new presented mathematical model of air entrainment process allows determining of air bubbles and water droplets concentrations distribution. The obtained theoretical and experimental results were in good agreement. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.4871

  12. Experimental analysis of the thermal entrainment factor of air curtains in vertical open display cabinets for different ambient air conditions

    International Nuclear Information System (INIS)

    The vertical open refrigerated display cabinets suffer alterations of their thermal performance and energy efficiency due to variations of ambient air conditions. The air curtain provides an aerothermodynamics insulation effect that can be evaluated by the thermal entrainment factor calculation as an engineering approximation or by the calculus of all sensible and latent thermal loads. This study presents the variation of heat transfer rate and thermal entrainment factor obtained through experimental tests carried out for different ambient air conditions, varying air temperature, relative humidity, velocity and its direction relatively to the display cabinet frontal opening. The thermal entrainment factor are analysed and compared with the total sensible and latent heats results for the experimental tests. From an engineering point of view, it is concluded that thermal entrainment factor cannot be used indiscriminately, although its use is suitable to design better cabinet under the same climate class condition.

  13. Sulfate Attack Resistance of Air-entrained Silica Fume Concrete under Dry-Wet Cycle Condition

    Institute of Scientific and Technical Information of China (English)

    YANG Jiansen; WANG Peiming; LI Haoxin; YANG Xu

    2016-01-01

    Based on the erosion resistant coefficient, the effects of water-cement ratio, air-entrained, silica fume content and sand ratio on the sulfate attack resistance of air-entrained silica fume concrete were studied by orthogonal experiments in order to explore its sulfate attack resistance under dry-wet condition. A more signiifcant model of concrete resistance to sulfate attack was also established, thus this work provided a strategy reference for quantitative design of sulfate attack resistant concrete. The experimental results show that dry-wet cycle deteriorates the concrete resistance to the sulfate attack, and leads to the remarkable declines of concrete strength and sulfate resistance. Air bubbles in the air-entrained silica fume concrete lower and delay the damage resulted from the crystallization sulfate salt. However this delay gradually disappears when most of the close bubbles are breached by the alternative running of the sulfate salt crystallization and the permeating pressure, and then the air bubbles are iflled with sulfate salt crystallization. The concrete is provided with the strongest sulfate resistance when it is prepared with the 0.47 water-binder ratio, 6.0% air-entrained, 5% silica fume and 30% sand ratio. The erosion resistant coefifcientsK80 andK150 of this concrete are increased by 9%, 7%, 9%, and 5% respectively as compared with those of concretes without silica fume and air entraining.

  14. Numerical investigation of air-entrainment in skimming flow over stepped spillways

    Directory of Open Access Journals (Sweden)

    Jiemin Zhan

    2016-05-01

    Full Text Available As a widely used flood energy dissipator, the stepped spillway can significantly dissipate the kinetic or hydraulic energy due to the air-entrainment in skimming flow over the steps. The free-surface aeration involves the sharp deformation of the free surface and the complex turbulent shear flows. In this study, the volume of fluid (VOF, mixture, and Eulerian methods are utilized to simulate the air-entrainment by coupling with the Reynolds-averaged Navier–Stokes/large eddy simulation (RANS/LES turbulence models. The free surface deformation, air volume fraction, pressure, and velocity are compared for the three different numerical methods. Only the Eulerian+RANS method fails to capture the free-surface aeration. The air volume fraction predicted by the VOF+LES method best matches the experimental measurement, while the mixture+LES method predicts the inception point of the air entrainment more accurately.

  15. What's All the Talc About? Air Entrainment in Dilute Pyroclastic Density Currents

    Science.gov (United States)

    Marshall, B. J.; Andrews, B. J.; Fauria, K.

    2015-12-01

    A quantitative understanding of air entrainment is critical to predicting the behaviors of dilute Pyroclastic Density Currents (PDCs), including runout distance, liftoff, and mass fractionation into co-PDC plumes. We performed experiments in an 8.5x6x2.6 meter tank using 20 micron talc powder over a range of conditions to describe air entrainment as a function of temperature, duration and mass flux. The experiments are reproducible and are scaled with respect to the densimetric and thermal Richardson numbers (Ri and RiT), Froude number, thermal to kinetic energy density ratio (TEb/KE), Stokes number, and Settling number, such that they are dynamically similar to natural dilute PDCs. Experiments are illuminated with a swept laser sheet and imaged at 1000 Hz to create 3D reconstructions of the currents, with ~1-2 cm resolution, at up to 1.5 Hz. An array of 30 high-frequency thermocouples record the precise temperature in the currents at 3 Hz. Bulk entrainment rates are calculated based on measured current volumes, surface areas, temperatures and velocities. Entrainment rates vary from ~0-0.9 and do not show simple variation with TEb/KE, Ri, or RiT. Entrainment does, however, increase with decreasing eruption duration and increasing mass flux. Our results suggest that current heads entrain air more efficiently than current bodies (>0.5 compared to ~0.1). Because shorter duration currents have proportionally larger heads, their bulk entrainment rates are controlled by those heads, whereas longer duration currents are dominated by their bodies. Our experiments demonstrate that air entrainment, which exerts a fundamental control on PDC runout and liftoff, varies spatially and temporally within PDCs.

  16. Quantification of hood effectiveness and entrained subsurface air in a Seattle Hospital

    Energy Technology Data Exchange (ETDEWEB)

    Dietz, R.N.; Goodrich, R.W.

    1994-05-01

    An underground 3-story wing of a hospital having problems with sewer air odors was tested with perfluorocarbon tracer (PFI) technology to quantify the performance of the mechanical ventilation system and determine the extent of sewer air entrainment and chemical hood effectiveness.

  17. Impact of air entrainment on the microstructure and mechanical performance of high performance mortar

    OpenAIRE

    Dils, Jeroen; Boel, Veerle; De Schutter, Geert

    2015-01-01

    At the Magnel Laboratory for Concrete Research an intensive vacuum mixer which can regulate the air pressure is available. As such the amount of entrapped air in cementitious materials can be varied. The effect of the reduced air content due to vacuum mixing on the rheology and workability was already investigated in previous work. Furthermore, the previous work investigated the influence of entrained air on the rheological properties. The impact of vacuum mixing on the compressive strength a...

  18. De-entrainment on vertical elements in air droplet cross flow

    International Nuclear Information System (INIS)

    De-entrainment phenomena on vertical elements in air-water droplet cross flow are generated using a horizontal array of water spray nozzles and a draft-induced wind tunnel. These conditions are used to obtain experimental values of the de-entrainment efficiency of isolated elements (25.4-, 63.5-, and 101.6-mm-diam cylinders and a 76.2-mm-square tube), and of an array of 101.6-mm-diam cylinders. A flow model is developed that extrapolates the de-entrainment efficiency of isolated elements through the use of a correlation for the interference effect to predict the efficiency of large arrays of similar elements. This simple model is shown to provide a good prediction of the de-entrainment efficiency of arrays in terms of the efficiency of an isolated element

  19. Influence of Air Temperature on the Performance of Different Water-Reducing Admixtures with Respect to the Properties of Fresh and Hardened Mortar

    OpenAIRE

    Wilson Ricardo Leal Silva; Luiz Roberto Prudêncio; Alexandre Lima Oliveira; Gabriela Damo; Eduardo Tochetto

    2010-01-01

    The performance of water-reducing admixtures used in concrete is affected by the weather conditions to which the concrete mixture is exposed. The most used WRAs are lignosulfonate, naphthalene, and polycarboxylate. However, they react differently to weather conditions, especially to air temperature. Therefore, it can be useful to evaluate how temperature affects admixture performance. In this study, the performance of three admixtures (naphthalene, lignosulfonate, and polycarboxylate) was eva...

  20. MEASUREMENT OF AIR ENTRAINMENT AND DUST EMISSION DURING SHELLED CORN RECEIVING OPERATIONS WITH SIMULATED HOPPER BOTTOM GRAIN TRAILERS

    Science.gov (United States)

    Dust emissions from grain elevator operations can be a safety and health risk, and a nuisance. Dust emission and air entrainment data are needed for designing adequate and effective control methods. This study measured the dust emitted and air entrained during corn receiving operations at an eleva...

  1. Foam and Entrained Air Management: A Practical Perspective

    Science.gov (United States)

    Mirza, Sal; Hoekstra, Philip M.

    Paper machines and the papermaking process have undergone remarkable changes in terms of chemistry applications and design parameters. These trends increase the likelihood that the stock will foam and generate turbulence, thus allowing air to be drawn in. For example, higher machine speeds and gap former technology cause more air to be present in the white water, which could ultimately lead to foam problems if not managed correctly.

  2. Experimental study of near-field air entrainment by subsonic volcanic jets

    Science.gov (United States)

    Solovitz, S.A.; Mastin, L.G.

    2009-01-01

    The flow structure in the developing region of a turbulent jet has been examined using particle image velocimetry methods, considering the flow at steady state conditions. The velocity fields were integrated to determine the ratio of the entrained air speed to the jet speed, which was approximately 0.03 for a range of Mach numbers up to 0.89 and. Reynolds numbers up to 217,000. This range of experimental Mach and Reynolds numbers is higher than previously considered for high-accuracy entrainment measures, particularly in the near-vent region. The entrainment values are below those commonly used for geophysical analyses of volcanic plumes, suggesting that existing 1-D models are likely to understate the tendency for column collapse. Copyright 2009 by the American Geophysical Union.

  3. The entrainment of air by water jet impinging on a free surface

    Energy Technology Data Exchange (ETDEWEB)

    Soh, Wee King [University of Wollongong, School of Mechanical, Materials and Mechatronics Engineering, Northfields Ave, NSW (Australia); Khoo, Boo Cheong [National University of Singapore, Department of Mechanical and Production Engineering, 10 Kent Ridge Crescent (Singapore); Yuen, W.Y. Daniel [BlueScope Steel Research, Port Kembla, NSW (Australia)

    2005-09-01

    High-speed cine and video photographs were used to capture the flow patterns of a column of water jet impinging into a pool of water. The impact results in air entrainment into water in the form of a void with no mixing between the water in the jet and the surrounding water. Conservation of fluid momentum shows that the rate of increase of the height of the air void depends on the drag coefficient of the jet front. By neglecting the frictional losses, the application of energy conservation yields an expression that relates the maximum height of the air void with the properties of the water jet. (orig.)

  4. BEHAVIOR OF AIR-ENTRAINED CONCRETE AFTER FREEZE-THAW CYCLES

    Institute of Scientific and Technical Information of China (English)

    Huaishuai Shang; Yupu Song; Jinping Ou

    2009-01-01

    The experimental study of air-entrained concrete specimens subjected to different cycles of freeze-thaw was completed. The dynamic modulus of elasticity, weight loss, the cubic compressive strength, compressive strength, tensile strength and cleavage strength of air-entrained concrete were measured after 0, 100, 200, 300, 400 cycles of freeze-thaw. The experimental results showed that the dynamic modulus of elasticity and strength decreased as the freeze-thaw was repeated. The influences of freeze-thaw cycles on the mechanical properties, the dynamic modulus of elasticity and weight loss were analyzed according to the experimental results. It can serve as a reference for the maintenance, design and the life prediction of dams, hydraulic structures, offshore structures, concrete roads and bridges in northern cold regions.

  5. Effect of Air Entrainment on Breakup of Plunging Liquid Jet into Water Pool

    International Nuclear Information System (INIS)

    The steam explosion intensity is largely dependent upon the degree of volumetric fractions of melt droplets and steam in the fuel-coolant mixture. The rate of melt jet breakup and droplet sizes are, therefore, the key physical parameters in the analysis of FCIs. In a recent OECD/NEA international program SERENA, the areas where research may be needed to reduce the level of uncertainties in the code predictions have been identified. The predicted void fractions in the mixture were generally much higher than experimental data and a deficiency in melt jet breakup modeling would be one of the primary causes. In this paper, an extended study of non-boiling liquid jet breakup from the previous jet breakup experiment is reported with an emphasis on the role of air entrainment by plunging liquid jet into water pool. An improved jet breakup model is also presented with comparison to the experimental data. Non-boiling liquid jet breakup experiment was conducted and the debris size was analyzed with a new jet breakup model with an emphasis on the role of air entrainment. The predicted debris size with consideration of entrained air showed good agreement with the experimental data

  6. Effect of Air Entrainment on Breakup of Plunging Liquid Jet into Water Pool

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Hyoungtak; Bang, Kwanghyun [Korea Maritime Univ., Busan (Korea, Republic of)

    2013-05-15

    The steam explosion intensity is largely dependent upon the degree of volumetric fractions of melt droplets and steam in the fuel-coolant mixture. The rate of melt jet breakup and droplet sizes are, therefore, the key physical parameters in the analysis of FCIs. In a recent OECD/NEA international program SERENA, the areas where research may be needed to reduce the level of uncertainties in the code predictions have been identified. The predicted void fractions in the mixture were generally much higher than experimental data and a deficiency in melt jet breakup modeling would be one of the primary causes. In this paper, an extended study of non-boiling liquid jet breakup from the previous jet breakup experiment is reported with an emphasis on the role of air entrainment by plunging liquid jet into water pool. An improved jet breakup model is also presented with comparison to the experimental data. Non-boiling liquid jet breakup experiment was conducted and the debris size was analyzed with a new jet breakup model with an emphasis on the role of air entrainment. The predicted debris size with consideration of entrained air showed good agreement with the experimental data.

  7. Material Properties Governing Co-Current Flame Spread: The Effect of Air Entrainment

    Science.gov (United States)

    Coutin, Mickael; Rangwala, Ali S.; Torero, Jose L.; Buckley, Steven G.

    2003-01-01

    A study on the effects of lateral air entrainment on an upward spreading flame has been conducted. The fuel is a flat PMMA plate of constant length and thickness but variable width. Video images and surface temperatures have allowed establishing the progression of the pyrolyis front and on the flame stand-off distance. These measurements have been incorporated into a theoretical formulation to establish characteristic mass transfer numbers ("B" numbers). The mass transfer number is deemed as a material related parameter that could be used to assess the potential of a material to sustain co-current flame spread. The experimental results show that the theoretical formulation fails to describe heat exchange between the flame and the surface. The discrepancies seem to be associated to lateral air entrainment that lifts the flame off the surface and leads to an over estimation of the local mass transfer number. Particle Image Velocimetry (PIV) measurements are in the process of being acquired. These measurements are intended to provide insight on the effect of air entrainment on the flame stand-off distance. A brief description of the methodology to be followed is presented here.

  8. Effect of low atmospheric pressure of plateau environment on air content and bubble stability of air-entrained concrete%高原低气压环境对引气混凝土含气量及气泡稳定性的影响

    Institute of Scientific and Technical Information of China (English)

    李雪峰; 付智

    2015-01-01

    该文利用低气压试验箱模拟高原气压环境,试验研究了不同配合比及初始含气量水平下环境气压的降低对引气混凝土含气量及其气泡稳定性的影响。结果表明:与常压相比,环境气压的降低能够显著削弱引气剂的引气能力,当混凝土配合比及引气剂掺量一定时,混凝土含气量随环境气压降低呈线性减少,当环境气压降低至50 kPa时,混凝土含气量降低约20%~49%。另外,低气压条件下混凝土气泡稳定性变差,具体表现为混凝土含气量经时损失变大,延长振捣时间导致低压混凝土损失更多气泡,二者均使低压下硬化混凝土的气泡间距系数增大,影响混凝土抗冻性。因此,在高原地区应通过采取优选引气剂类型、增大引气剂掺量以及避免过振等技术措施,以确保高原地区引气混凝土含气量能够达到抗冻设计要求。%The effect of atmospheric pressure reduction of environment on air content and bubble stability of air-entrained concrete were experimentally studied using low-pressure test chamber to stimulate the plateau environment. Three different mixing proportions and three different levels of the initial air content of concretes were prepared for study, and four different common types of air-entraining admixture, saponin, alkyl sulfonate, abietic soap and polyether, were used in the experiments. The results indicated that the change of atmospheric pressure of environment had a significant impact on the performance of air-entraining admixtures. When the mix proportions of concrete and the amount of air-entraining admixtures took a certain value respectively, the air content of fresh concrete decreased linearly with the drop of atmospheric pressure. When the atmospheric pressure was 50 kPa, the air content of fresh concrete fell by roughly 20% to 49%. The higher the air content of fresh concrete mixed in normal atmospheric pressure, the faster the air

  9. Using Neutron Radiography to Quantify Water Transport and the Degree of Saturation in Entrained Air Cement Based Mortar

    Science.gov (United States)

    Lucero, Catherine L.; Bentz, Dale P.; Hussey, Daniel S.; Jacobson, David L.; Weiss, W. Jason

    Air entrainment is commonly added to concrete to help in reducing the potential for freeze thaw damage. It is hypothesized that the entrained air voids remain unsaturated or partially saturated long after the smaller pores fill with water. Small gel and capillary pores in the cement matrix fill quickly on exposure to water, but larger pores (entrapped and entrained air voids) require longer times or other methods to achieve saturation. As such, it is important to quantitatively determine the water content and degree of saturation in air entrained cementitious materials. In order to further investigate properties of cement-based mortar, a model based on Beer's Law has been developed to interpret neutron radiographs. This model is a powerful tool for analyzing images acquired from neutron radiography. A mortar with a known volume of aggregate, water to cement ratio and degree of hydration can be imaged and the degree of saturation can be estimated.

  10. A method for measuring the mass flow rate of pulverized coal entrained in air

    International Nuclear Information System (INIS)

    An on line mass flow rate meter of pulverized coal entrained in air was relied on concurrent measurements of medium density and flow velocity together with on line computation from this information. An X-ray transmission densitometer has been developed for the measurement of medium density. Because of the fluctuations of the density and air pressure inside the transfer tube, several types of sensors, deployed in an upstream/downstream pair, appear suitable for the fluctuation detection and for the velocity determination through a cross correlation technique. Both of Hall effect and capacitance sensors were considered as the fluctuation detectors

  11. On the relationship between air entrainment, internal flows and closure mechanism in a ventilated supercavity

    Science.gov (United States)

    Karn, Ashish; Arndt, Roger; Hong, Jiarong

    2015-11-01

    An understanding of underlying physics behind ventilation demand is critical for the operation of underwater vehicles based on ventilated supercavitation for a number of reasons viz. gas entrainment requirements for cavity formation and sustenance. The prior studies on the ventilation demand have reported that the gas entrainment requirement to form a supercavity is substantially larger than that needed to sustain it. This phenomenon, known as ventilation hysteresis, is particularly important from the viewpoint of reduction in gas requirements. However, little physical insights into this phenomenon has yet been provided. In this study, systematic investigations are conducted into ventilation hysteresis with respect to the formation and collapse behaviors of ventilated supercavities. It is suggested that the supercavity formation process is driven by bubble coalescence, whereas its collapse is related to the pressure difference across the supercavity interface at its rear portion. Further, we examine the relationship between ventilation hysteresis, supercavity closures and air entrainment requirements for supercavity formation and sustenance under steady and unsteady flow conditions. These observations are directly related to the internal flows inside the supercavity.

  12. Turbulent hydraulic jumps: Effect of Weber number and Reynolds number on air entrainment and micro-bubble generation

    Science.gov (United States)

    Mortazavi, Milad; Mani, Ali

    2015-11-01

    Air entrainment in breaking waves is a ubiquitous and complex phenomenon. It is the main source of air transfer from atmosphere to the oceans. Furthermore, air entrainment due to ship-induced waves contributes to bubbly flows in ship wakes and also affect their performance. In this study, we consider a turbulent hydraulic jump as a canonical setting to investigate air entrainment due to turbulence-wave interactions. The flow has an inlet Froude number of 2.0, while three different Weber numbers (We = 1820, 729, 292), and two different Reynolds numbers (Re = 11000, 5500) based on the inlet height and inlet velocity are investigated. Air entrainment is shown to be very sensitive to the We number, while Re number has a minor effect. Wave breaking and interface collisions are significantly reduced in the low Weber number cases. As a result, micro-bubble generation is significantly reduced with decreasing Weber number. Vortex shedding events are observed to emerge at the toe of the jump in all of the cases. For high Weber number regimes, shedding of vortices is accompanied by engulfment of air pockets into the jump in a periodic manner, while for lower Webber number regimes such events are significantly suppressed. Reynolds number is shown to have a negligible effect on the air entrainment, wave breaking and micro-bubble generation, contrary to the previous assumptions in other studies. Supported by ONR.

  13. Experimental investigation on the droplet entrainment from interfacial waves in air-water horizontal stratified flow

    International Nuclear Information System (INIS)

    It was mainly due to the fact that droplet entrainment affects the Peak Cladding Temperature (PCT) of the nuclear fuel rod in the Postulated accident conditions of NPP. Recently, droplet entrainment in the horizontally arranged primary piping system for the NPP is of interest because it affects directly the steam binding phenomena in the steam generators. Pan and Hanratty correlation is the only applicable one for the droplet entrainment rate model for horizontal flow. Moreover, there are no efforts for the model development on the basis of the droplet entrainment principal and physics phenomena. More recently, Korea Atomic Energy Research Institute (KAERI) proposed a new mechanistic droplet generation model applicable in the horizontal pipe for the SPACE code. However, constitutive relations in this new model require three model coefficients which have not yet been decided. The purpose of present work is determining three model coefficients by visualization experiment. For these model coefficients, the major physical parameters regarding the interfacial disturbance wave should be measured in this experiments. There are the wave slope, liquid fraction, wave hypotenuse length, wave velocity, wave frequency, and wavelength in the major physical parameters. The experiment was conducted at an air water horizontal rectangular channel with the PIV system. In this study, the experimental conditions were stratified-way flow during the droplet generation. Three coefficients were determined based on several data related to the interfacial wave. Additionally, we manufactured the parallel wire conductance probe to measure the fluctuating water level over time, and compared the wave height measured by the parallel wire conductance probe and image processing from images taken by high speed camera. Experimental investigation was performed for droplet entrainment from phase interface wave in an air-water stratified flow. In the experiments, we measured major physical parameters

  14. Experimental investigation on the droplet entrainment from interfacial waves in air-water horizontal stratified flow

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Byeong Geon; Yun, Byong Jo [Pusan national Univ., Pusan (Korea, Republic of); Kim, Kyoung Du [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    It was mainly due to the fact that droplet entrainment affects the Peak Cladding Temperature (PCT) of the nuclear fuel rod in the Postulated accident conditions of NPP. Recently, droplet entrainment in the horizontally arranged primary piping system for the NPP is of interest because it affects directly the steam binding phenomena in the steam generators. Pan and Hanratty correlation is the only applicable one for the droplet entrainment rate model for horizontal flow. Moreover, there are no efforts for the model development on the basis of the droplet entrainment principal and physics phenomena. More recently, Korea Atomic Energy Research Institute (KAERI) proposed a new mechanistic droplet generation model applicable in the horizontal pipe for the SPACE code. However, constitutive relations in this new model require three model coefficients which have not yet been decided. The purpose of present work is determining three model coefficients by visualization experiment. For these model coefficients, the major physical parameters regarding the interfacial disturbance wave should be measured in this experiments. There are the wave slope, liquid fraction, wave hypotenuse length, wave velocity, wave frequency, and wavelength in the major physical parameters. The experiment was conducted at an air water horizontal rectangular channel with the PIV system. In this study, the experimental conditions were stratified-way flow during the droplet generation. Three coefficients were determined based on several data related to the interfacial wave. Additionally, we manufactured the parallel wire conductance probe to measure the fluctuating water level over time, and compared the wave height measured by the parallel wire conductance probe and image processing from images taken by high speed camera. Experimental investigation was performed for droplet entrainment from phase interface wave in an air-water stratified flow. In the experiments, we measured major physical parameters

  15. Inerting characteristics of entrained atomized water on premixed methane-air flame

    Institute of Scientific and Technical Information of China (English)

    Cai Feng; Wang Ping; Zhou Jiebo; Li Chao

    2015-01-01

    A combustion tube experiment platform was designed and used to study the inerting conditions and capacity of entrained atomized water on premixed methane–air flame. The structure of a laminar flame of premixed methane–air gas and the process of interaction between atomized water and flame was recorded, and the rules of combustion velocity, stability and strength rate of laminar flame were experi-mentally studied. The inerting process and mechanism was analyzed, and the characteristics of inerting premixed methane–air gas within explosion limits by atomized water were acquired. The research results show that:for the premixed methane–air gas with a concentration of 7%, the minimum inerting atomized water flux is 20.8 mL/(m2 min);for the premixed methane–air gas with a concentration of 9%, the mini-mum inerting atomized water flux is 32.9 mL/(m2 min);for the premixed methane–air gas with a concen-tration of 11%, the minimum inerting atomized water flux is 44.6 mL/(m2 min). The research results are significant for extinguishing methane flame and inhibiting of methane explosion using atomized water.

  16. An experimental investigation of the air entrainment in the shutdown cooling system during mid-loop operation

    International Nuclear Information System (INIS)

    An experimental study on the air entrainment phenomena during mid-loop operation has been performed for Ulchin 3 and 4 nuclear power plant (UCN 3 and 4). The UCN 3 and 4 is the standard Combustion Engineering (CE) System 80, two-loop, 2825 MWt pressurized water reactor which is currently under construction in Korea. This study was undertaken by Korea Atomic Energy Research Institute to provide a basis for modification of CE system 80 design which has relatively small mid-loop operating range, and to investigate the impact of the air entrainment on the shutdown cooling pump. A 1/4 scale model test was performed for two shutdown cooling suction nozzle configurations, with and without bellmouth entry, to obtain data relative to air ingestion and vortex formation at the shutdown cooling suction nozzle during mid-loop operation. The test model size was determined based on Froude number corresponding to that which occurs in plants by considering that the Weber number and Reynolds number are large enough to ensure that liquid surface tension and viscosity would not significantly affect the vortex formation. An empirical correlation between the flow rate and the critical submergence was obtained with respect to the Froude number. The impact of the air entrainment of the pump was also investigated to select parameters for plant operators to monitor the onset of air entrainment into shutdown cooling system (SCS). Effects of the bellmouth entry on the critical submergence were also investigated. (author)

  17. Influence of Air Temperature on the Performance of Different Water-Reducing Admixtures with Respect to the Properties of Fresh and Hardened Mortar

    Directory of Open Access Journals (Sweden)

    Wilson Ricardo Leal Silva

    2010-01-01

    Full Text Available The performance of water-reducing admixtures used in concrete is affected by the weather conditions to which the concrete mixture is exposed. The most used WRAs are lignosulfonate, naphthalene, and polycarboxylate. However, they react differently to weather conditions, especially to air temperature. Therefore, it can be useful to evaluate how temperature affects admixture performance. In this study, the performance of three admixtures (naphthalene, lignosulfonate, and polycarboxylate was evaluated at 15, 25, and 35°C by means of the flow table test, mixture air content, and compressive strength. Moreover, mixture temperature was monitored and time-temperature curves were plotted in order to assess whether the admixtures affected cement hydration reactions at different temperatures. The final results indicate that an increase in temperature leads to an increase in saturation dosage; lignosulfonate had the most pronounced retarding effect, followed by polycarboxylate, and finally, naphthalene, and considering the weather conditions in the area where the study was carried, the final finding would be that the naphthalene-based admixture had the best performance.

  18. Formation of air-entraining vortices at horizontal intakes without approach flow induced circulation

    Institute of Scientific and Technical Information of China (English)

    Mustafa GOGUS; Mete KOKEN; Ali BAYKARA

    2016-01-01

    The aim of this experimental study is to investigate the effects of hydraulic parameters on the formation of air-entraining vortices at horizontal intake structures without approach flow induced circulation. Six intake pipes of different diameters were tested in the study. The intake pipe to be tested was horizontally mounted to the front side of a large reservoir and then for a wide range of discharges experiments were conducted and critical submergences were detected with adjustable approach channel sidewalls. Empiri- cal equations were derived for the dimensionless critical submergence as a function of the relevant dimensionless parameters. Availa- ble data is also checked for the possible scale effect. Then, these obtained equations were compared with the similar ones in the literature which showed a quite good agreement.

  19. Downward flow of water with entrained air in a nonuniformaly heated subdivided annulus

    International Nuclear Information System (INIS)

    This paper describes an experimental study in which water was fed to a vertical annulus, entraining air in downward flow. The annulus was subdivided by longitudinal fins into four subchannels and was heated with an azimuthally varying heat flux. A bypass was provided to simulate flow in parallel channels. For steady liquid flow, inlet temperature, and pressure boundary conditions, the power was increased until critical heat flux was reached. Overheating characteristics were grouped according to the prevailing flow pattern. In annular flows (jL L L) overheating occurs by diverting inlet flow to the bypass and again involves the whole test section. Except at the very lowest flow rates, critical heat flux occurs when the effluent liquid temperature is below saturation

  20. Keeping warm with fur in cold water: entrainment of air in hairy surfaces

    Science.gov (United States)

    Nasto, Alice; Regli, Marianne; Brun, Pierre-Thomas; Clanet, Christophe; Hosoi, Anette

    2015-11-01

    Instead of relying on a thick layer of body fat for insulation as many aquatic mammals do, fur seals and otters trap air in their dense fur for insulation in cold water. Using a combination of model experiments and theory, we rationalize this mechanism of air trapping underwater for thermoregulation. For the model experiments, hairy surfaces are fabricated using laser cut molds and casting samples with PDMS. Modeling the hairy texture as a network of capillary tubes, the imbibition speed of water into the hairs is obtained through a balance of hydrostatic pressure and viscous stress. In this scenario, the bending of the hairs and capillary forces are negligible. The maximum diving depth that can be achieved before the hairs are wetted to the roots is predicted from a comparison of the diving speed and imbibition speed. The amount of air that is entrained in hairy surfaces is greater than what is expected for classic Landau-Levich-Derjaguin plate plunging. A phase diagram with the parameters from experiments and biological data allows a comparison of the model system and animals.

  1. Study on effects of air-entraining and anti-foaming on performance and apparent morphology of fair-faced concrete%引气剂与消泡剂对清水混凝土性能与表观形貌的影响

    Institute of Scientific and Technical Information of China (English)

    黄快忠; 龚明子; 陈茜; 刘尊玉; 李式龙; 连亚明

    2014-01-01

    There are important effects of air-entraining admixture and anti-foaming admixture on performance of concrete.It discussed the influence of the different air-entraining and anti-foaming ratio in polycarboxylate superplasticizer on concrete fluidity,air content and strength.The optimal ratio between the two made plain fair-faced concrete showed better performance and apparent morphology.The re-sults showed that,when air-entraining admixture dosage was two over ten thousand and anti-foaming dosage was one over ten thousand, the apparent morphology of fair-faced concrete was the best.%引气剂与消泡剂对清水混凝土的性能与表观形貌有重要的影响。论述了不同引气和消泡比例的聚羧酸高效减水剂对清水混凝土流动性、含气量、强度与硬化后表观形貌的影响。为使清水混凝土表现出更好的性能和美观的表面形貌,两者存在一个最佳比例。结果表明:当引气剂掺量为2%、消泡剂掺量为1%时,清水混凝土的表观形貌最佳。

  2. Improving the behavior of concrete exposed to fire by using an air entraining agent (AEA: Assessment of spalling

    Directory of Open Access Journals (Sweden)

    D'Aloia L.

    2013-09-01

    Full Text Available Several concrete mixes have been designed to evaluate the influence of an air entraining agent (AEA on spalling. Tests have been performed under the ISO curve (occasionally under the HCinc curve on specimens of various sizes and shapes to assess spalling. Results were somehow erratic on the smallest specimens whereas the beneficial effect of the air-bubble network could be emphasized on slabs.

  3. Influence of Nozzle geometry on spray shape, particle size, spray velocity and Air entrainment of high pressure Diesel spray

    OpenAIRE

    Hespel, Camille; Blaisot, Jean-Bernard; Margot, Xandra; Patouna, S.; Cessou, Armelle; Lecordier, Bertrand

    2010-01-01

    International audience Air/fuel mixing process in the combustion chamber of Diesel engines plays an important role on the combustion efficiency. This mixing depends on the particle size distribution in the spray, on the local velocity of fuel droplets in the spray and on the air entrainment. Nozzle geometry as well as nozzle internal flow conditions influence many of these spray properties. An experimental study of the influence of the nozzle geometry on these properties has been conducted...

  4. Experimental study on durability improvement of fly ash concrete with durability improving admixture.

    Science.gov (United States)

    Quan, Hong-zhu; Kasami, Hideo

    2014-01-01

    In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete, the compressive strength of fly ash concrete can be improved by 10%-20%, and the drying shrinkage is reduced by 60%. Carbonation resistance of concrete is roughly proportional to water-cement ratio regardless of water-binder ratio and fly ash replacement ratio. For the specimens cured in air for 2 weeks, the freezing-thawing resistance is improved. In addition, by making use of durability improving admixture, it is easier to control the air content and make fly ash concrete into nonair-entraining one. The quality of fly ash concrete is thereby optimized. PMID:25013870

  5. Experimental Study on Durability Improvement of Fly Ash Concrete with Durability Improving Admixture

    Directory of Open Access Journals (Sweden)

    Hong-zhu Quan

    2014-01-01

    Full Text Available In order to improve the durability of fly ash concrete, a series of experimental studies are carried out, where durability improving admixture is used to reduce drying shrinkage and improve freezing-thawing resistance. The effects of durability improving admixture, air content, water-binder ratio, and fly ash replacement ratio on the performance of fly ash concrete are discussed in this paper. The results show that by using durability improving admixture in nonair-entraining fly ash concrete, the compressive strength of fly ash concrete can be improved by 10%–20%, and the drying shrinkage is reduced by 60%. Carbonation resistance of concrete is roughly proportional to water-cement ratio regardless of water-binder ratio and fly ash replacement ratio. For the specimens cured in air for 2 weeks, the freezing-thawing resistance is improved. In addition, by making use of durability improving admixture, it is easier to control the air content and make fly ash concrete into nonair-entraining one. The quality of fly ash concrete is thereby optimized.

  6. An analysis of air entrainment into residual heat removal pump during the refueling cavity draindown for Kori Unit 2

    International Nuclear Information System (INIS)

    In 1998, 1999 and 2000, the Kori Unit 2 has experienced the air entrainment and loss of flow in the residual heat removal (RHR) pump during a planned draining of the refueling cavity without the fuel assemblies in the reactor vessel. The water level of the refueling cavity was 1 m above reactor vessel flange when the transients occurred and a similiar event was not known so far in domestic and foreign nuclear power plants. The cause of air entrainment into the RHR pump is analyzed using the RELAP5/MOD3 code in this study. Also, it is qualitatively analyzed the reason why such transients do not occur when fuel assemblies are loaded in reactor vessel

  7. Study on Strength and Ultrasonic Velocity of Air-Entrained Concrete and Plain Concrete in Cold Environment

    OpenAIRE

    Huai-shuai Shang; Ting-hua Yi; Xing-xing Guo

    2014-01-01

    Nondestructive testing technology is essential in the quality inspection of repair, alteration, and renovation of the existing engineering, especially for concrete structure in severe environment. The objective of this work is to deal with the behavior of ultrasonic velocity and mechanical properties of plain concrete and air-entrained concrete subjected to freeze-thaw cycles (F-T-C). The ultrasonic velocity and mechanical properties (tensile strength, compressive strength, cubic compressive ...

  8. Study on Strength and Ultrasonic Velocity of Air-Entrained Concrete and Plain Concrete in Cold Environment

    Directory of Open Access Journals (Sweden)

    Huai-shuai Shang

    2014-01-01

    Full Text Available Nondestructive testing technology is essential in the quality inspection of repair, alteration, and renovation of the existing engineering, especially for concrete structure in severe environment. The objective of this work is to deal with the behavior of ultrasonic velocity and mechanical properties of plain concrete and air-entrained concrete subjected to freeze-thaw cycles (F-T-C. The ultrasonic velocity and mechanical properties (tensile strength, compressive strength, cubic compressive strength, and splitting strength of C30 air-entrained concrete and plain concrete with different water-cement ratio (water-cement ratio was 0.55, 0.45, and 0.50, resp. after F-T cycles were measured. The influences of F-T cycles on ultrasonic velocity and mechanical properties of C30 air-entrained concrete and plain concrete were analyzed. And the relationship between mechanical properties and ultrasonic velocity was established. The experimental results can be useful for the design of new concrete structure, maintenance and life prediction of existing concrete structure such as offshore platform and concrete dock wall.

  9. ENTRAINMENT MODELS

    Science.gov (United States)

    This presentation presented information on entrainment models. Entrainment models use entrainment hypotheses to express the continuity equation. The advantage is that plume boundaries are known. A major disadvantage is that the problems that can be solved are rather simple. The ...

  10. Potential of ANSYS CFX 12 for the determination of the minimum cover of pump intake nozzles to avoid air entrainment

    International Nuclear Information System (INIS)

    For a reliable and economic pump operation the homogeneous fluid influx is an important parameter. Unfavorable influx conditions cause vibrations, noise development, decrease or breakdown of the delivery rate and increased power consumption. Very often air ingress due to turbulences in the intake region of the pump is causing the disturbances. The authors show that the CFD code ABSYS CFX 12 allows - at least for rotation-free inlet flow - to identify the water surface deformation and to determine the required minimum water cover to avoid air entrainment. Further mesh refinement and improved modeling of the two-phase flow could enhance the quantitative agreement with experimental data.

  11. Entrainment Heat Flux Computed with Lidar and Wavelet Technique in Buenos Aires During Last Chaitén Volcano Eruption

    Science.gov (United States)

    Pawelko, Ezequiel Eduardo; Salvador, Jacobo Omar; Ristori, Pablo Roberto; Pallotta, Juan Vicente; Otero, Lidia Ana; Quel, Eduardo Jaime

    2016-06-01

    At Lidar Division of CEILAP (CITEDEF-CONICET) a multiwavelength Raman-Rayleigh lidar optimized to measure the atmospheric boundary layer is being operated. This instrument is used for monitoring important aerosol intrusion events in Buenos Aires, such as the arrival of volcanic ashes from the Chaitén volcano eruption on May 2008. That was the first monitoring of volcanic ash with lidar in Argentina. In this event several volcanic ash plumes with high aerosol optical thickness were detected in the free atmosphere, affecting the visibility, surface radiation and therefore, the ABL evolution. In this work, the impact of ashes in entrainment flux ratio is studied. This parameter is obtained from the atmospheric boundary layer height and entrainment zone thickness using algorithms based on covariance wavelet transform.

  12. Two-phase numerical study of the flow field formed in water pump sump: influence of air entrainment

    International Nuclear Information System (INIS)

    In a pump sump it is imperative that the amount of non-homogenous flow and entrained air be kept to a minimum. Free air-core vortex occurring at a water-intake pipe is an important problem encountered in hydraulic engineering. These vortices reduce pump performances, may have large effects on the operating conditions and lead to increase plant operating costs.This work is an extended study starting from 2006 in LML and published by ISSA and al. in 2008, 2009 and 2010. Several cases of sump configuration have been numerically investigated using two specific commercial codes and based on the initial geometry proposed by Constantinescu and Patel. Fluent and Star CCM+ codes are used in the previous studies. The results, obtained with a structured mesh, were strongly dependant on main geometrical sump configuration such as the suction pipe position, the submergence of the suction pipe on one hand and the turbulence model on the other hand. Part of the results showed a good agreement with experimental investigations already published. Experiments, conducted in order to select best positions of the suction pipe of a water-intake sump, gave qualitative results concerning flow disturbances in the pump-intake related to sump geometries and position of the pump intake. The purpose of this paper is to reproduce the flow pattern of experiments and to confirm the geometrical parameter that influences the flow structure in such a pump. The numerical model solves the Reynolds averaged Navier-Stokes (RANS) equations and VOF multiphase model. STAR CCM+ with an adapted mesh configuration using hexahedral mesh with prism layer near walls was used. Attempts have been made to calculate two phase unsteady flow for stronger mass flow rates and stronger submergence with low water level in order to be able to capture air entrainment. The results allow the knowledge of some limits of numerical models, of mass flow rates and of submergences for air entrainment. In the validation of this

  13. Entrainment of Ambient air into H2O/Ar Arc Plasma Jet

    Czech Academy of Sciences Publication Activity Database

    Kavka, Tetyana; Hrabovský, Milan; Konrád, Miloš; Kopecký, Vladimír; Sember, Viktor; Chumak, Oleksiy

    Bari : Department of Chemistry, University of Bari, 2003 - (d'Agostino, R.; Favia, P.; Fracassi, F.; Palumbo, F.), s. - [International Symposium on Plasma Chemistry/16th./. Taormina (IT), 22.06.2003-27.06.2003] R&D Projects: GA ČR GA202/01/1563 Institutional research plan: CEZ:AV0Z2043910 Keywords : plasma jet, entrainment , enthalpy probe Subject RIV: BL - Plasma and Gas Discharge Physics

  14. Particle re-entrainment from a powder deposit in an horizontal air flow; Mise en suspension d'une contamination particulaire par ecoulement d'air

    Energy Technology Data Exchange (ETDEWEB)

    Alloul, L.; Witschger, O. [CEA/Saclay, Inst. de Protection et de Surete Nucleaire, IPSN/DPEA/SERAC, Lab. de Physique et Metrologie des Aerosols et du Confinement, 91 - Gif-sur-Yvette (France); Renoux, A. [Paris-12 Univ., Lab. de Physique des Aerosols et de Transfert des Contaminations, 94 - Creteil (France); Le Dur, D. [Aerolab, 91 - Courtaboeuf (France); Monnatte, J. [COGEMA, Branche Combustible et Recyclage, Service Qualite Surete, 78 - Saint-Quentin-en-Yvelines (France)

    2000-07-01

    Particle re-entrainment from surfaces to turbulent air flow is an important subject in many different fields like nuclear safety, environmental air pollution, sediment transport by wind, surface contamination in semiconductor operations. Theoretical and experimental studies have been numerous and cover different aspects of the phenomena. Although a number of theoretical works have been devoted for describing the mechanisms of detachment of primary spherical particles form flat smooth surfaces in a turbulent flow, experimental data are still needed in order to comparison. Moreover, the knowledge of the effect of parameters related to the deposit (monolayer, multilayer, cone-like pile), the powder particles (particle-size distribution, adhesive properties), the surface (roughness,...),the airflow (velocity, acceleration, turbulence) or the environment (humidity,...) is still in an elementary stage. The main objective of our work is to contribute to the understanding and quantification of the parameters that govern the particle re-entrainment from a powder deposit in an turbulent horizontal airflow. Therefore, a new experimental facility called BISE (french acronym for wind tunnel for studying particle re-entrainment by airflow) has been designed and built in our laboratory. (authors)

  15. Study of air entrainment in high pressure spray: optics diagnostics and application to the Diesel injection; Etude de l'entrainement d'air dans un spray haute pression: diagnostics optiques et application a l'injection diesel

    Energy Technology Data Exchange (ETDEWEB)

    Arbeau, A.

    2004-12-15

    The actual development of the engine must reply to a will of fuel consumption reduction and to norms more and more strict concerning the pollutant emissions. Although the Diesel engines are efficient, the NO{sub x} and particle emissions mainly come from the existence of wealthy fuel zone preventing an optimal combustion. Therefore, the air / fuel mixing preparation, highly controlled by the air entrainment in spray, is essential. In this context, we have developed metrological tools in order to analyse the air entrainment mechanism in a dense spray. The Particle Image Velocimetry (PIV) technique is first applied to a conical spray with an injection pressure less than 100 bars to study the air entrainment in spray. A transfer of the methodologies allows then the characterisation and the understanding of the air entrainment mechanism in high pressure full spray (injection pressure less than 1600 bars) type Diesel one. The influence of injection parameters (injection pressure and back pressure) on the mixing rate is studied. The increase of the injection pressure from 800 to 1600 bars implies an increase of the mixing rate of 60 %. Moreover, the thermodynamic conditions of the ambient air, simulated by the chamber back pressure, widely favours the mixing rate. Actually, this latter increases of 350 % when the chamber back pressure varies from 1 to 7 bars. The experimental results do not follow classical laws of air entrainment in one-phase flow jet with variable density, but are in good agreement with an integral model for air entrainment in an axisymmetric full spray. Finally, the Fluorescence Particle Image Velocimetry (FPIV) is introduced in order to extend the PIV application field in dense two-phase flows. (author)

  16. Stratocumulus cloud deepening through entrainment

    Science.gov (United States)

    Randall, D. A.

    1984-01-01

    Under a substantial range of realistic conditions, stratocumulus cloud top entrainment is noted to either deepen an existing cloud layer or produce clouds in an unsaturated mixed layer, though the entrained air is warmer and drier than the mixed-layer air. These results, which apply irrespective of entrainment rate-determining mechanism, imply that the cloud top entrainment instability discussed by Randall (1980) and Deardorff (1980) does not necessarily destroy a layer cloud. Examples are given which include soundings, marine layer data, and simulation results produced by the UCLA general circulation model.

  17. Free-surface Flow Interface And Air-Entrainment Modelling Using OpenFOAM

    OpenAIRE

    Lopes, Pedro

    2013-01-01

    The use of hydraulic structures to control flooding has a history of long practice within civil engineering infrastructure. Hydraulic structures under turbulent flow conditions frequently involve free surface fl ow and interactions between air and water. This can be observed in different kinds of structures, e.g. gullies, manholes or stepped spillways. In this doctoral program, Computational Fluid Dynamics numerical models will be used to simulate...

  18. Analysis of transient flows in gasoline direct injection systems: effects on unsteady air entrainment by the spray; Analyse des ecoulements transitoires dans les systemes d'injection directe essence: effets sur l'entrainement d'air instationnaire du spray

    Energy Technology Data Exchange (ETDEWEB)

    Delay, G.

    2005-03-15

    The aim of this study is to determine instantaneous liquid flow rate oscillations effect on non stationary air entrainment of an injector conical spray (Gasoline Direct Injection). The tools we use are either experimental or numerical ones. An instantaneous flow rate determination method is used. It is based on pulsated flows physics and only requires the velocity at the centerline of a pipe mounted just before the injector. So, it is possible to 'rebuild' the instantaneous velocity distributions and then to get the instantaneous liquid flow rate (Laser Doppler Anemometry measurements). A mechanical and hydraulics modeling software (AMESim) is necessary to get injector outlet flow rate. Simulations are validated by both 'rebuilding' method results and common rail pressure measurements. Fluorescent Particle Image Velocimetry (FPIV), suited to dense two -phase flows, is used to measure air flow around and inside the conical spray. Velocity measurements close to the spray frontier are used to compute instantaneous air entrainment. Considering droplets momentum exchange with air and thanks to droplets diameters and liquid velocities measurements at the nozzle exit, a transient air entrainment model is proposed according to FPIV measurements. (author)

  19. Airborne & SAR Synergy Reveals the 3D Structure of Air Bubble Entrainment in Internal Waves and Frontal Zones

    Science.gov (United States)

    da Silva, J. C. B.; Magalhaes, J. M.; Batista, M.; Gostiaux, L.; Gerkema, T.; New, A. L.

    2013-03-01

    Internal waves are now recognised as an important mixing mechanism in the ocean. Mixing at the base of the mixed layer and in the seasonal thermocline affects the properties of those water masses which define the exchange of heat and freshwater between the atmosphere and ocean. The breaking of Internal Solitary Waves (ISWs) contributes significantly to turbulent mixing in the near-surface layers, through the continual triggering of instabilities as they propagate and shoal towards the coast or shallow topography. Here we report some results of the EU funded project A.NEW (Airborne observations of Nonlinear Evolution of internal Waves generated by internal tidal beams). The airborne capabilities to observe small scale structure of breaking internal waves in the near-shore zone has been demonstrated in recent studies (e.g. Marmorino et al., 2008). In particular, sea surface thermal signatures of shoaling ISWs have revealed the turbulent character of these structures in the form of surface “boil” features. On the other hand, some in situ measurements of internal waves and theoretical work suggest subsurface entrainment of air bubbles in the convergence zones of ISWs (Serebryany and Galybin, 2009; Grimshaw et al., 2010). We conducted airborne remote sensing observations in the coastal zone off the west Iberian Peninsula (off Lisbon, Portugal) using high resolution imaging sensors: LiDAR (Light Detection And Ranging), hyperspectral cameras (Eagle and Hawk) and thermal infrared imaging (TABI-320). These measurements were planned based on previous SAR observations in the region, which included also near-real time SAR overpasses (ESA project AOPT-2423 and TerraSAR-X project OCE-0056). The airborne measurements were conducted from board the NERC (Natural Environmental Research Centre) Do 228 aircraft in the summer of 2010. The TABI-320 thermal airborne broadband imager can distinguish temperature differences as small as one-twentieth of a degree and operates in the

  20. Low Temperature Concrete Admixture

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    Performing construction processes under the cold weather condition requires construction engineers to plan operations considering low temperature condition. Concrete admixture mostly chemically interact with the constituents of concrete and affect the properties and characteristics of the fresh and hardened concrete and its durability. The purposes of the admixtures include water reduction, high strength, corrosion protection, crack control, finish enhancement, flowability, etc. One of the in...

  1. Performance of rice husk ash produced using a new technology as a mineral admixture in concrete

    International Nuclear Information System (INIS)

    This article investigates the use of a new technique for the controlled combustion of Egyptian rice husk to mitigate the environmental concerns associated with its uncontrolled burning and provide a supplementary cementing material for the local construction industry. The reactor used provides efficient combustion of rice husk in a short residency time via the suspension of processed particles by jets of a process air stream that is forced though stationary angled blades at high velocity. Investigations on the rice husk ash (RHA) thus produced included oxide analysis, X-ray diffraction, carbon content, grindability, water demand, pozzolanic activity index, surface area, and particle size distribution measurements. In addition, concrete mixtures incorporating various proportions of silica fume (SF) and Egyptian RHA (EG-RHA) produced at different combustion temperatures were made and compared. The workability, superplasticizer and air-entraining admixture requirements, and compressive strength at various ages of these concrete mixtures were evaluated, and their resistance to rapid chloride penetrability and deicing salt surface scaling were examined. Test results indicate that contrary to RHA produced using existing technology, the superplasticizer and air-entraining agent requirements did not increase drastically when the RHA developed in this study was used. Compressive strengths achieved by concrete mixtures incorporating the new RHA exceeded those of concretes containing similar proportions of SF. The resistance to surface scaling of RHA concrete was better than that of concrete containing similar proportions of SF. While the chloride penetrability was substantially decreased by RHA, it remained slightly higher than that achieved by SF concrete

  2. Entrained Flow Gasification of Biomass

    DEFF Research Database (Denmark)

    Qin, Ke

    The present Ph. D. thesis describes experimental and modeling investigations on entrained flow gasification of biomass and an experimental investigation on entrained flow cogasification of biomass and coal. A review of the current knowledge of biomass entrained flow gasification is presented....... Biomass gasification experiments were performed in a laboratory-scale atmospheric pressure entrained flow reactor with the aim to investigate the effects of operating parameters and biomass types on syngas products. A wide range of operating parameters was involved: reactor temperature, steam/carbon ratio......, excess air ratio, oxygen concentration, feeder gas flow, and residence time. Wood, straw, and lignin were used as biomass fuels. In general, the carbon conversion was higher than 90 % in the biomass gasification experiments conducted at high temperatures (> 1200 °C). The biomass carbon that was not...

  3. ENTRAINMENT BY LIGAMENT-CONTROLLED EFFERVESCENT ATOMIZER-PRODUCED SPRAYS

    Science.gov (United States)

    Entrainment of ambient air into sprays produced by a new type of effervescent atomizer is reported. Entrainment data were obtained using a device similar to that described by Ricou & Spalding (1961). Entrainment data were analyzed using the model of Bush & Sojka (1994), in concer...

  4. Entrainment Concepts Revisited

    NARCIS (Netherlands)

    Roenneberg, Till; Hut, Roelof; Daan, Serge; Merrow, Martha

    2010-01-01

    The traditional approaches to predict entrainment of circadian clocks by light are based on 2 concepts that were never successfully unified: the non-parametric approach assumes that entrainment occurs via discrete daily phase shifts while the parametric approach assumes that entrainment involves cha

  5. Application of Orthogonal Experiment in Compound Admixture of Freezing Mine Shaft Lining Concrete%正交法在冻结井壁砼复合外加剂试验中的应用

    Institute of Scientific and Technical Information of China (English)

    宗翔; 徐颖; 李寅珺

    2012-01-01

    In order to achieve the setting and hardening of mine shaft lining concrete under the minus temperature in freezing construction and to meet the demands of every performance of concrete, the technique of compounding air entraining admixture and antifreezing admixture and early strength water reducing admixture was applied in this research. Based on the Orthogonal experimental design, several mix proportions of compound admixture for early strength liquid mine shaft lining concrete were developed in the laboratory. The data collected in this research provide reference for the optimum mix proportion of the adulteration quantity of the concrete admixture. The results show that the 2. 1% amount of compound antifreezing admixture achieves favorable effects of liquid,early strength,freezing prevention and antifreezing.%为了使冻结施工井壁混凝土能够在负温条件下凝结与硬化,并满足其各项性能要求,采用引气剂+防冻剂+早强减水剂复合的技术路线,通过正交试验设计复配了适应冻结施工早强流态井壁混凝土的复合外加剂.通过试验分析最终确定各组分掺量之间的最佳配比.复合外加剂的掺量为2.1%,可起到流态、早强、防冻及抗冻的作用.

  6. Progress in Lignin-based Concrete Admixtures%含木质素基混凝土外加剂的研究进展

    Institute of Scientific and Technical Information of China (English)

    谌凡琪

    2012-01-01

    综述了木质素在混凝土外加剂中的应用。工业木质素,尤其是木质素磺酸盐,可以充当混凝土减水剂、缓凝剂、引气剂和泵送剂。由于未经改性的工业木质素性能不够理想,为了提高木质素基混凝土添加剂的性能,宜对其进行适当的改性。碱木质素经过氧化、磺化、磺甲基化、接枝共聚等改性后,可以得到具有良好性能的混凝土外加剂。%The applications of lignin derivatives in concrete admixtures are reviewed. Technical lignins, especially lignosulfonates, can serve as concrete water reducers, retarders, air entraining agents and pumping agents. The performance of lignin is not good. Some appropriate modifications are sometimes required in order to improve the performance of the lignin-based concrete admixtures. Lignin-based concrete admixtures with good performaces can be obtained fxom alkali lignin after modifications such as oxidation, sulfonation, sulfomethylation and graft copolymerization.

  7. 关于加气混凝土砌块墙体质量控制的探讨%Discuss the Quality Control of Air Entraining Concrete Block Wall

    Institute of Scientific and Technical Information of China (English)

    贺玉超

    2014-01-01

    Air entraining concrete block is the common con-crete block in building wal , and the crack problems in air entraining concrete block wal are common in the building wal , which brought great trouble to the construction enterp-rises. The article analyzes the factors to result in the crack of the wal , and effective prevention and improvement measures are put forward.%加气混凝土砌块是建筑墙体中较为常见的砌块,加气混凝土砌块墙体裂缝问题在建筑房屋墙体中比较常见,给建筑施工企业带来了极大的麻烦。文章对导致墙体开裂的因素进行了深入分析,并提出了有效地防治及改善措施。

  8. PERFORMANCE OF MICROWAVE INCINARATED RICE HUSK ASH AND USED ENGINE OIL AS A GREEN CONCRETE ADMIXTURES

    Directory of Open Access Journals (Sweden)

    B. SALMIA

    2015-12-01

    Full Text Available The utilization of waste materials in the construction industry is a novel approach let alone if these materials can further enhance the durability of the structures. Amongst the waste materials identified to be incorporated in this study is Rice Husk Ash (RHA and Used Engine Oil (UEO. Productions of these waste materials are colossal with annual volume of 1.35 billion gallon and 40 million tons of used engine oil and rice husk respectively. The main aim of this research is to establish the effects of these two waste materials (as ingredients in concrete. The rice husk was burn using microwave incinerator to produce better quality of Microwave Incinerated Rice Husk Ash (MIRHA. The pozzolanic reactivity of MIRHA helped to enhance concrete durability. The used engine oil acted as an admixture that improved the fresh state of the concrete. Workability, entrained air and compressive strength tests were conducted and the result showed that the concrete illustrated better performance compared to control sample in terms of workability, air contain and compressive strength.

  9. Entrainment in vertical annular two-phase flow

    International Nuclear Information System (INIS)

    Prediction of amount of entrained droplets or entrainment fraction in annular two-phase flow is essential for the estimation of dryout condition and analysis of post dryout heat transfer in light water nuclear reactors and steam boilers. In this study, air-water and organic fluid (Freon-113) annular flow entrainment experiments have been carried out in 9.4 and 10.2 mm diameter test sections, respectively. Both the experiments covered three distinct pressure conditions and wide range of liquid and gas flow conditions. The organic fluid experiments simulated high pressure steam-water annular flow conditions. In each of the experiments, measurements of entrainment fraction, droplet entrainment rate and droplet deposition rate have been performed by using a liquid film extraction method. A simple, explicit and non-dimensional correlation developed by Sawant et al. (2008a) for the prediction of entrainment fraction is further improved in this study in order to account for the existence of critical gas and liquid flow rates below which no entrainment is possible. Additionally, a new correlation is proposed for the estimation of minimum liquid film flow rate at the maximum entrainment fraction condition. The improved correlation successfully predicted the newly collected air-water and Freon-113 entrainment fraction data. Furthermore, the correlations satisfactorily compared with the air-water, helium-water and air-genklene experimental data measured by Willetts (1987). (author)

  10. Entrainment separator performance

    International Nuclear Information System (INIS)

    Clean and dust-loaded ACS entrainment separators mounted upstream of HEPA filters were exposed to a combination of fine water mist and steam at about 700C from one to four hours. In every trial, the ACS entrainment separator prevented measurable deterioration of performance in the following HEPA filter. Droplet size-efficiency evaluation of the ACS entrainment separators showed that, within the accuracy of the measurements, they meet all service requirements and are fully equal to the best separator units available for service on pressurized water reactors

  11. Aerosol entrainment from a sparged non-Newtonian slurry.

    Science.gov (United States)

    Fritz, Brad G

    2006-08-01

    Previous bench-scale experiments have provided data necessary for the development of empirical models that describe aerosol entrainment from bubble bursting. However, previous work has not been extended to non-Newtonian liquid slurries. Design of a waste treatment plant on the Hanford Site in Washington required an evaluation of the applicability of these models outside of their intended range. For this evaluation, aerosol measurements were conducted above an air-sparged mixing tank filled with simulated waste slurry possessing Bingham plastic rheological properties. Three aerosol-size fractions were measured at three sampling heights and for three different sparging rates. The measured entrainment was compared with entrainment models. One model developed based on bench-scale air-water experiments agreed well with measured entrainment. Another model did not agree well with the measured entrainment. It appeared that the source of discrepancy between measured and modeled entrainment stemmed from application beyond the range of data used to develop the model. A possible separation in entrainment coefficients between air-water and steam-water systems was identified. A third entrainment model was adapted to match experimental conditions and fit a posteri to the experimental data, resulting in a modified version that resulted in estimated entrainment rates similar to the first model. PMID:16933643

  12. Admixture elements as indicators of fluorite genesis

    International Nuclear Information System (INIS)

    Present book is devoted to comparative analysis of abundance and distribution of admixture elements in fluorite-mineral. The data on composition and content of admixture elements in fluorite was generalized. The hydrothermal deposits were characterized on mineral types.

  13. Increasing jet entrainment, mixing and spreading

    Science.gov (United States)

    Farrington, Robert B.

    1994-01-01

    A free jet of air is disturbed at a frequency that substantially matches natural turbulences in the free jet to increase the entrainment, mixing, and spreading of air by the free jet, for example in a room or other enclosure. The disturbances are created by pulsing the flow of air that creates the free jet at the desired frequency. Such pulsing of the flow of air can be accomplished by sequentially occluding and opening a duct that confines and directs the flow of air, such as by rotating a disk on an axis transverse to the flow of air in the duct.

  14. Prospects for Admixture Mapping of Complex Traits

    OpenAIRE

    McKeigue, Paul M

    2004-01-01

    Admixture mapping extends to human populations the principles that underlie linkage analysis of an experimental cross. For detecting genes that contribute to ethnic variation in disease risk, admixture mapping has greater statistical power than family-linkage studies. In comparison with association studies, admixture mapping requires far fewer markers to search the genome and is less affected by allelic heterogeneity. Statistical-analysis programs for admixture mapping are now available, and ...

  15. Shrinkage Reducing Admixture for Concrete

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    Concrete shrinkage cracking is a common problem in all types of concrete structures, especially for structures and environments where the cracks are prevalent and the repercussions are most severe. A liquid shrinkage reducing admixture for concrete, developed by GRACE Construction Products and ARCO Chemical Company, that reduces significantly the shrinkage during concrete drying and potentially reduces overall cracking over time.

  16. An Observational Study of Entrainment Rate in Deep Convection

    Directory of Open Access Journals (Sweden)

    Xiaohao Guo

    2015-09-01

    Full Text Available This study estimates entrainment rate and investigates its relationships with cloud properties in 156 deep convective clouds based on in-situ aircraft observations during the TOGA-COARE (Tropical Ocean Global Atmosphere Coupled Ocean Atmosphere Response Experiment field campaign over the western Pacific. To the authors’ knowledge, this is the first study on the probability density function of entrainment rate, the relationships between entrainment rate and cloud microphysics, and the effects of dry air sources on the calculated entrainment rate in deep convection from an observational perspective. Results show that the probability density function of entrainment rate can be well fitted by lognormal, gamma or Weibull distribution, with coefficients of determination being 0.82, 0.85 and 0.80, respectively. Entrainment tends to reduce temperature, water vapor content and moist static energy in cloud due to evaporative cooling and dilution. Inspection of the relationships between entrainment rate and microphysical properties reveals a negative correlation between volume-mean radius and entrainment rate, suggesting the potential dominance of homogeneous mechanism in the clouds examined. In addition, entrainment rate and environmental water vapor content show similar tendencies of variation with the distance of the assumed environmental air to the cloud edges. Their variation tendencies are non-monotonic due to the relatively short distance between adjacent clouds.

  17. Influence on the physical-mechanical properties of portland-cement mortar, have admixtures of colophony and tannin

    Directory of Open Access Journals (Sweden)

    Fernández Cánovas, M.

    1989-12-01

    Full Text Available The colophony has been used as an admixture in the Portland cement mortar with the intention to observe its influence on the air content, water absorption, adhesive capacity and mechanical properties. The results obtained have shown that, the colophony acts as air entrainment, reduces the permeability and improves the adhesion between the past and aggregates. Likewise, the addition of tannin and montan wax to the colophony has the efect of reducing the formation of foam and improves the impermeability of the mortar.

    Se ha empleado la colofonia como aditivo en el mortero de cemento portland con el fin de observar su influencia sobre el contenido de aire, absorción de agua, capacidad adhesiva y propiedades mecánicas. Los resultados obtenidos han puesto de manifiesto que la colofonia actúa como aireante, aumenta la impermeabilidad y mejora la adherencia de la pasta al árido. Asimismo, la adición de tanino y cera montana a la colofonia tiene el efecto de reducir la formación de espuma y mejorar también la impermeabilidad del mortero.

  18. Ancient Admixture in Human History

    Science.gov (United States)

    Patterson, Nick; Moorjani, Priya; Luo, Yontao; Mallick, Swapan; Rohland, Nadin; Zhan, Yiping; Genschoreck, Teri; Webster, Teresa; Reich, David

    2012-01-01

    Population mixture is an important process in biology. We present a suite of methods for learning about population mixtures, implemented in a software package called ADMIXTOOLS, that support formal tests for whether mixture occurred and make it possible to infer proportions and dates of mixture. We also describe the development of a new single nucleotide polymorphism (SNP) array consisting of 629,433 sites with clearly documented ascertainment that was specifically designed for population genetic analyses and that we genotyped in 934 individuals from 53 diverse populations. To illustrate the methods, we give a number of examples that provide new insights about the history of human admixture. The most striking finding is a clear signal of admixture into northern Europe, with one ancestral population related to present-day Basques and Sardinians and the other related to present-day populations of northeast Asia and the Americas. This likely reflects a history of admixture between Neolithic migrants and the indigenous Mesolithic population of Europe, consistent with recent analyses of ancient bones from Sweden and the sequencing of the genome of the Tyrolean “Iceman.” PMID:22960212

  19. Experimental study of entrainment phenomenon in a trapped vortex combustor

    Institute of Scientific and Technical Information of China (English)

    Zhang Rongchun; Fan Weijun

    2013-01-01

    Trapped vortex combustor (TVC) is an advanced low-pollution gas turbine combustor,with the adoption of staged combustion technique.To achieve low-pollutant emission and better combustion performance,the proportion of the air flow in each combustion zone should be precisely determined in the design of the combustor.Due to the presence of entrainment phenomenon,the total air flow in the cavity zone is difficult to estimate.To overcome the measurement difficulty,this study adopts the indirect measurement approach in the experimental research of entrainment phenomenon in the cavity.In accordance with the measurement principle,a TVC model fueled by methane is designed.Under two experimental conditions,i.e.with and without direct air intake in the cavity,the influence of the mainstream air flow velocity,the air intake velocity in the cavity,the height of inlet channel,the structure of holder and the structural proportion of the cavity on entrainment in the cavity is studied,respectively,through experiment at atmospheric temperature and pressure.The results suggest that the air flow velocity of mainstream,the air intake velocity of the cavity and the structure of the holder exert significant influence on the air entrainment,while the influence of structural proportion of the cavity is comparatively insignificant.The square root of momentum ratio of cavity air to mainstream air could be used to analyze the correlation of the entrainment data.

  20. Venous admixture in COPD: Pathophysiology and therapeutic approaches

    OpenAIRE

    Cooper, CB; Celli, B

    2008-01-01

    Chronic obstructive and interstitial lung diseases impair pulmonary gas exchange leading to wasted ventilation (alveolar dead space) and wasted perfusion (venous admixture). These two fundamental types of abnormality represent opposite ends of the spectrum of ventilation-perfusion mismatch with V̇/Q̇ ratios of infinity and zero. Treatment approaches that improve airway function, reduce air trapping and hyperinflation have received much attention and might be successful at ameliorating the pro...

  1. Entrainment of the Neurospora circadian clock

    NARCIS (Netherlands)

    Merrow, M; Boesl, C; Ricken, J; Messerschmitt, M; Goedel, M; Roenneberg, T

    2006-01-01

    Neurospora crassa has been systematically investigated for circadian entrainment behavior. Many aspects of synchronization can be investigated in this simple, cellular system, ranging from systematic entrainment and drivenness to masking. Clock gene expression during entrainment and entrainment with

  2. Entrainment and mixing mechanism in monsoon clouds

    Science.gov (United States)

    Bera, Sudarsan; Prabhakaran, Thara; Pandithurai, Govindan; Brenguier, Jean-Louis

    2015-04-01

    Entrainment and consequent mixing impacts the cloud microphysical parameters and droplet size distribution (DSD) significantly which are very important for cloud radiative properties and the mechanism for first rain drop formation. The entrainment and mixing mechanisms are investigated in this study using in situ observations in warm cumulus clouds over monsoon region. Entrainment is discussed in the framework of the homogeneous and inhomogeneous mixing concepts and their effects on cloud droplet size distribution, number concentration, liquid water content and mean radius are described. The degree of homogeneity increases with droplet number concentration and adiabatic fraction, indicating homogeneous type mixing in the cloud core where dilution is less. Inhomogeneous mixing is found to be a dominating process at cloud edges where dilution is significant. Cloud droplet size distribution (DSD) is found to shift towards lower sizes during a homogeneous mixing event in the cloud core whereas spectral width of DSD decreases due to inhomogeneous mixing at cloud edges. Droplet size spectra suggests that largest droplets are mainly formed in the less diluted cloud core while diluted cloud edges have relatively smaller droplets, so that raindrop formation occurs mainly in the core of the cloud. The origin of the entrained parcels in deep cumulus clouds is investigated using conservative thermodynamical parameters. The entrained parcels originate from a level close to the observation level or slightly below through lateral edges. Cloud edges are significantly diluted due to entrainment of sub-saturated environmental air which can penetrate several hundred meters inside the cloud before it gets mixed completely with the cloud mass. Less diluted parcels inside the cloud core originates from a level much below the cloud base height. Penetrating downdraft from cloud top is seldom observed at the observation level and strong downdrafts may be attributed to in-cloud oscillation

  3. Water Entrainment in Concrete

    DEFF Research Database (Denmark)

    Jensen, Ole Mejlhede; Hansen, Per Freiesleben

    This report gives a survey of different techniques for incorporation of designed, water-filled cavities in concrete: Water entrainment. Also an estimate of the optimum size of the water inclusions is given. Water entrainment can be used to avoid self-desiccation and self-desiccation shrinkage...... during hydration [1,26]. What is needed is some sort of container which retains the shape of the water when mixed into the concrete. The container may function based on several different physical or chemical principles. Cells and gels are examples of containers found in nature. A cell membrane provides...... a boundary to water, whereas a polymer network incorporates water in its intersticious space with its affinity due to interaction energy and polymer entropy. Such containers allow water to be stored as an entity. In relation to concrete the water encapsulation may be accomplished either before or after start...

  4. Defining the Entrainment Zone in Stratocumulus-topped Boundary Layers

    Science.gov (United States)

    Wang, Q.; Zhou, M.; Kalogiros, J. A.; Lenschow, D. H.; Dai, C.; Wang, S.

    2010-12-01

    The presence of an entrainment zone near the top of the stratocumulus-topped boundary layers has been identified by many early studies. However, the definition of the entrainment zone was rather vague. We have examined the fine vertical variations of cloud liquid water content, wind, temperature and humidity near the stratocumulus top and developed a new method to identify the entrainment zone objectively. Aircraft measurements from various field projects in stratocumulus-topped boundary layers are used, taking advantage of the fast sampling capability of many of the aircraft sensors. Because of the inhomogeneous mixing of two air masses with distinctively different thermodynamic properties, the magnitude of temperature perturbations within the entrainment zone is significantly larger than those above or below. This characteristics is used to define the upper and lower boundaries of the entrainment zone using a wavelet spectra analyses. The definition of the entrainment zone is further evaluated by the presence of a linear mixing line through mixing line analyses. Various other interfaces at the cloud top are also examined, including the cloud interface, temperature interface (inversion), and moisture interface. The heights of these interfaces are examined relative to the height of the entrainment zone. This study also systematically revealed the presence of turbulence above the local cloud top and/or above the entrainment zone. Wind shear near the cloud top is one possible source that generated local turbulence. Other potential sources of turbulence will also be discussed.

  5. Entrainment and mixing in vertical buoyant light-gas plumes

    International Nuclear Information System (INIS)

    A simple model is developed to determine the entrainment coefficient and the spread of a light-gas plume in a quiescent atmosphere. Experiments performed with low-velocity saltwater/freshwater and helium-in-air jets indicate that buoyant gas plumes spread significantly faster than thermal plumes. The calculated effluent concentrations are in excellent agreement with those measured when an entrainment coefficient of 0.15 is used in the plume equations. This is significantly higher than the entrainment coefficients of 0.075 to 0.093 reported for thermal plumes

  6. Entrainment region phenomena for a large plane shear layer

    Science.gov (United States)

    Ali, S. K.; Klewicki, C. L.; Disimile, P. J.; Lawson, I.; Foss, J. F.

    1985-01-01

    The subatmospheric test section of the present free shear layer facility allows the entrainment air to be introduced with a negligible disturbance level. The very low frequency oscillations, which are prominently observed in the entrainment stream and which are present throughout the shear layer, are attributed to an inherent instability in the transition from a boundary layer to a free shear layer state. The basic features of the disturbance field are documented herein.

  7. Timescales of Massive Human Entrainment

    OpenAIRE

    Riccardo Fusaroli; Marcus Perlman; Alan Mislove; Alexandra Paxton; Teenie Matlock; Rick Dale

    2014-01-01

    The past two decades have seen an upsurge of interest in the collective behaviors of complex systems composed of many agents. In this paper, we extend concepts of entrainment to the dynamics of human collective attention. We demonstrate that large scale human entrainment may hold across a number of distinct scales, in an exquisitely time locked fashion. Using a large scale database of human communication data, we analyze and describe three different time scales of human entrainment in electro...

  8. Timescales of Massive Human Entrainment

    CERN Document Server

    Fusaroli, Riccardo; Mislove, Alan; Paxton, Alexandra; Matlock, Teenie; Dale, Rick

    2014-01-01

    The past two decades have seen an upsurge of interest in the collective behaviors of complex systems composed of many agents. In this paper, we extend concepts of entrainment to the dynamics of human collective attention. We demonstrate that large scale human entrainment may hold across a number of distinct scales, in an exquisitely time locked fashion. Using a large scale database of human communication data, we analyze and describe three different time scales of human entrainment in electronic media. We sought a distinct shared experience that provided a test bed for quantifying large scale human entrainment. We conducted a detailed investigation of the real time unfolding of human entrainment, as expressed by the content and patterns of hundreds of thousands of messages on Twitter, during the 2012 US presidential debates. By time locking these data sources, we quantify the real time impact of the debate on human attention. We show that social behavior covaries second by second to the interactional dynamics...

  9. Power plant intake entrainment analysis

    International Nuclear Information System (INIS)

    Power plant condenser cooling water intake entrainment of fish eggs and larvae is becoming an issue in evaluating environmental impacts around the plants. Methods are required to evaluate intake entrainment on different types of water bodies. Presented in this paper is a derivation of the basic relationships for evaluating entrainment from the standing crop of fish eggs and larvae for different regions of a water body, and evaluating the rate of entrainment from the standing crop. These relationships are coupled with a 3D hydrodynamic and transport model that provides the currents and flows required to complete the entrainment evaluation. Case examples are presented for a simple river system, and for the more complex Delaware River Estuary with multiple intakes. Example evaluations are made for individual intakes, and for the cumulative impacts of multiple intakes

  10. Investigating the Sensitivity of Model Intraseasonal Variability to Minimum Entrainment

    Science.gov (United States)

    Hannah, W. M.; Maloney, E. D.

    2008-12-01

    Previous studies have shown that using a Relaxed Arakawa-Schubert (RAS) convective parameterization with appropriate convective triggers and assumptions about rain re-evaporation produces realistic intraseasonal variability. RAS represents convection with an ensemble of clouds detraining at different heights, each with different entrainment rate, the highest clouds having the lowest entrainment rates. If tropospheric temperature gradients are weak and boundary layer moist static energy is relatively constant, then by limiting the minimum entrainment rate deep convection is suppressed in the presence of dry tropospheric air. This allows moist static energy to accumulate and be discharged during strong intraseasonal convective events, which is consistent with the discharge/recharge paradigm. This study will examine the sensitivity of intra-seasonal variability to changes in minimum entrainment rate in the NCAR-CAM3 with the RAS scheme. Simulations using several minimum entrainment rate thresholds will be investigated. A frequency-wavenumber analysis will show the improvement of the MJO signal as minimum entrainment rate is increased. The spatial and vertical structure of MJO-like disturbances will be examined, including an analysis of the time evolution of vertical humidity distribution for each simulation. Simulated results will be compared to observed MJO events in NCEP-1 reanalysis and CMAP precipitation.

  11. Three-field modeling with droplet entrainment and de-entrainment models for TRAC-M

    International Nuclear Information System (INIS)

    discussed. The calculation results show that Kataoka and Ishii's entrainment model predicts more accurately than the other in simulation of experiments with porous sinter liquid injection method. However, the applicability of Kataoka and Ishii's entrainment model in different liquid injection type is not valid. Wurtz's entrainment model is valid in prediction of high pressure steam/water experiments and equilibrium entrainment of air/water experiment with diameter of 3.18 cm. With this, Wurtz's entrainment model is selected as the basic model for the present study and for air/water, porous-sinter cases, the use of Kataoka and ishii's model is selected. The final form of the three-field model is validated against various experimental data including steam-water data. the predicted data agrees with experimental data with the RMS error of 23.9%

  12. Stability investigation of total parenteral nutrition admixture prepared in a hospital pharmacy

    Directory of Open Access Journals (Sweden)

    Mirković Dušica

    2008-01-01

    Full Text Available Background/Aim. In the cases when nutrition of patients can not be orally nor enterally performed, parenteral nutrition is a method of the therapy that provides more successful and rapid recovery. In that way, hospitalization can be significantly shorter, healing costs reduced and mortality minimized. Total parenteral nutrition (TPN admixtures are the most complex systems which contain amino acids, carbohydrates, lipid emulsion, macroelectrolytes (Na+, K+, Ca2+, Mg2+, Cl-, SO42-, PO43-, oligoelements, hydro- and liposoluble vitamines, heparin, insulin and water. Concerning the mentioned complexity, special attention should be payed to physicochemical and microbiological stability of a mixture, because of interactions among components, that can be very hard to analyze. The aim of this study was to investigate the problem of stability of TPN admixtures prepared in a hospital pharmacy. Methods. Admixture TPN was aseptically prepared in laminar air - flow environment on the basis of the specified order in supplementing components and additives to basic solutions. Solutions were kept in sterile multicompartment ethylene-vinyl-acetate bags. After preparation and slow homogenization, TPN admixtures were submitted to physicochemical and microbiological stability analyses in various period of time. The assessment of physical stability of TPN admixture was done on the basis of visual inspection, determination of pH value and measuring of particle size. The investigation of sterility and pyrogenic test were performed according to Ph. Yug. V regulations. Results. Physico-chemical and microbiological analyses were applied and no significant changes in visual sense, pH value and droplet size stability of the TPN admixture were observed during the period of 60 hours. The lipid droplets were smaller in size than 5 μm, that is the most common pharmacopoeia requirement. Conclusion. The results of our study confirmed that a TPN admixture prepared in a hospital

  13. Experiment on gas entrainment at free surface. Study on bubble entrainment mechanism

    International Nuclear Information System (INIS)

    This paper deals with unsteady behavior of free surface vortices at an upper plenum in a reactor. In the compact reactor investigated, the coolant velocity increases and gas entrainment at the free surface is feared to occur. The estimation of the onset condition of gas entrainment is an important factor for design of the reactor. Therefore, the study on the unsteady characteristics of the free surface vortex is important. The gas entrainment due to the free surface vortex is a time series of phenomena; (1) formation of a vortex dimple on the free surface, (2) development of the gas core of the vortex by a downward flow, and (3) gas entrainment by the separation of bubbles at a tip of the gas core. In this study, the gas entrainment by the bubble separation is focused on and the unsteady behavior of the gas core by the fluctuations of the flow conditions is investigated experimentally. In the experiment, an apparatus having a simple geometry, similar to that used in the study on a steady free surface vortex, was used. The circulation was generated in a cylindrical vessel with a tangential slit injection and the downward flow was by a suction pipe at the bottom. The free surface vortex developed due to the circulation and the downward flow. The working fluid was water and the vessel is under the atmospheric air. In order to know the unsteady behavior of the gas core, the injection flow rate into the vessel was changed as a sine wave, and the time series of the gas core geometry was measured by a stereo image processing. The results of the study are mainly as follows; (1) The gas core length changed with the water flow rate but the shape of the fluctuation of gas core length was not a sine wave. The gas core length decreased suddenly when the water flow rate decreased. This corresponds that the characteristic time of the flow for the increasing flow rate is longer than that for the decreasing flow rate. (2) The gas core length under the fluctuating flow rate was

  14. High-temperature entrained flow gasification of biomass

    DEFF Research Database (Denmark)

    Qin, Ke; Lin, Weigang; Jensen, Peter Arendt;

    2012-01-01

    Biomass (wood and straw) gasification has been studied in a laboratory scale atmospheric pressure entrained flow reactor. Effects of reaction temperature, steam/carbon molar ratio, excess air ratio, and biomass type on the solid, liquid and gas products were investigated. The biomass was completely...

  15. Dry air entrainment into convective clouds

    Science.gov (United States)

    Telford, J. W.

    1977-01-01

    A systematic approach to the study of atmospheric turbulent motion is discussed in terms of weather modification. The background of cloud physics, and the mixing process are described. A zero-g study is proposed to enable the basic experimental data to be collected so that theory may be developed to generalize results for practical applications.

  16. Estimation of convective entrainment properties from a cloud-resolving model simulation during TWP-ICE

    Science.gov (United States)

    Zhang, Guang J.; Wu, Xiaoqing; Zeng, Xiping; Mitovski, Toni

    2015-12-01

    The fractional entrainment rate in convective clouds is an important parameter in current convective parameterization schemes of climate models. In this paper, it is estimated using a 1-km-resolution cloud-resolving model (CRM) simulation of convective clouds from TWP-ICE (the Tropical Warm Pool-International Cloud Experiment). The clouds are divided into different types, characterized by cloud-top heights. The entrainment rates and moist static energy that is entrained or detrained are determined by analyzing the budget of moist static energy for each cloud type. Results show that the entrained air is a mixture of approximately equal amount of cloud air and environmental air, and the detrained air is a mixture of ~80 % of cloud air and 20 % of the air with saturation moist static energy at the environmental temperature. After taking into account the difference in moist static energy between the entrained air and the mean environment, the estimated fractional entrainment rate is much larger than those used in current convective parameterization schemes. High-resolution (100 m) large-eddy simulation of TWP-ICE convection was also analyzed to support the CRM results. It is shown that the characteristics of entrainment rates estimated using both the high-resolution data and CRM-resolution coarse-grained data are similar. For each cloud category, the entrainment rate is high near cloud base and top, but low in the middle of clouds. The entrainment rates are best fitted to the inverse of in-cloud vertical velocity by a second order polynomial.

  17. Wind profiler mixing depth and entrainment measurements with chemical applications

    Energy Technology Data Exchange (ETDEWEB)

    Angevine, W.M.; Trainer, M.; Parrish, D.D.; Buhr, M.P.; Fehsenfeld, F.C. [NOAA Aeronomy Lab., Boulder, CO (United States); Kok, G.L. [NCAR Research Aviation Facility, Boulder, CO (United States)

    1994-12-31

    Wind profiling radars operating at 915 MHz have been present at a number of regional air quality studies. The profilers can provide a continuous, accurate record of the depth of the convective mixed layer with good time resolution. Profilers also provide information about entrainment at the boundary layer top. Mixing depth data from several days of the Rural Oxidants in the Southern Environment II (ROSE II) study in Alabama in June, 1992 are presented. For several cases, chemical measurements from aircraft and ground-based instruments are shown to correspond to mixing depth and entrainment zone behavior observed by the profiler.

  18. Cloud microphysical effects of turbulent mixing and entrainment

    CERN Document Server

    Kumar, Bipin; Shaw, Raymond A

    2013-01-01

    Turbulent mixing and entrainment at the boundary of a cloud is studied by means of direct numerical simulations that couple the Eulerian description of the turbulent velocity and water vapor fields with a Lagrangian ensemble of cloud water droplets that can grow and shrink by condensation and evaporation, respectively.The focus is on detailed analysis of the relaxation process of the droplet ensemble during the entrainment of subsaturated air, in particular the dependence on turbulence time scales, droplet number density, initial droplet radius and particle inertia. We find that the droplet evolution during the entrainment process is captured best by a phase relaxation time that is based on the droplet number density with respect to the entire simulation domain and the initial droplet radius. Even under conditions favoring homogeneous mixing, the probability density function of supersaturation at droplet locations exhibits initially strong negative skewness, consistent with droplets near the cloud boundary be...

  19. Fixed and entrained flow gasifiers - examples

    Energy Technology Data Exchange (ETDEWEB)

    Anon.

    2009-03-15

    Gasification is a flexible, reliable, and clean energy technology that can turn a variety of low-value feedstocks into high-value products, help reduce our dependence on foreign oil and natural gas, and can provide a clean alternative source of baseload electricity, fertilizers, fuels, and chemicals. According to the Gasification Technologies Council (www.gasification.org) today there are more than 420 gasifiers currently in use in some 140 facilities worldwide. By 2015, worldwide gasification capacity is projected to grow 70%, with 80% of the growth occurring in Asia. The prime movers behind this expected growth are the chemical, fertilizer, and coal-to-liquids industries in China, oil sands in Canada, polygeneration (hydrogen and power or chemicals) and substitute natural gas in the United States, and refining in Europe. Looking far into the future gasification can be a link technology to a hydrogen economy as it produces the hydrogen that will be needed for fuel cells. The heart of a gasification plant is the gasifier. There are several basic designs, distinguished by the use of wet or dry feed, the use of air or oxygen, the reactor's flow direction (up-flow, downflow, or circulating), and the gas cooling process. Hereunder, in addition to Abraham who gives examples of a fluidized and an entrained flow gasifier, the Lurgi fixed bed gasifier as well as the two entrained flow gasifiers from Shell and GE as examples for worldwide utilized gasifiers are shortly described. (orig.)

  20. Early hydration cement Effect of admixtures superplasticizers

    Directory of Open Access Journals (Sweden)

    Puertas, F.

    2001-06-01

    Full Text Available Early hydration of portland cement with superplasticizer admixtures of different nature has been studied. These admixtures were: one based on melamine synthetic, other based on vinyl copolymer and other based on polyacrylate copolymers. The dosage of the formers were constant (1% weigth of cement and for the third, the influence of admixture dosage was also evaluated, giving dosage values among 1-0.3%. The pastes obtained were studied by conduction calorimetry, XRD and FTIR. Also the apparent fluidity was determined by "Minislump" test. The main results obtained were: a superplasticizers admixtures used, regardless of their nature and for the polycarboxilate one the dosage, retard the silicate hydration (specially, alite phase, b The ettringite formation is affected by the nature of the admixture. cA relationship between the dosage of admixture based on polycarboxilates and the time at the acceleration has been established. A lineal relation (y = 11.03 + 16.05x was obtained. From these results is possible to know, in function of dosage admixture, the time when the masive hydration products and the setting times are produced. Also the total heat releases in these reactions is independent of the nature and dosage of admixture, saying that in all cases the reactions are the same.

    En el presente trabajo se ha estudiado la hidratación inicial de un cemento portland aditivado con superplastificantes de diferente naturaleza. Dichos aditivos fueron: uno basado en melaminas sintéticas, otro en copolímeros vinilicos y otro en policarboxilatos. La dosificación de los dos primeros se fijó constante en 1% en peso con relación al cemento, mientras que para el tercero se evaluó, también, la influencia de la dosificación, tomando proporciones desde el 1% hasta el 0,3%. Las pastas obtenidas se estudiaron por: calorimetría de conducción, DRX y FTIR. También se determinó la fluidez de la pasta a través del ensayo del "Minislump ". Los

  1. Investigation of the Entrainment Phenomenon Using a Scaling Approach

    Science.gov (United States)

    Kishore, Aravind; Ghia, Urmila

    2014-11-01

    Air entrainment is a commonly observed phenomenon; we see it when filling a glass with water from a faucet, in the frothing of the ocean surface, in white water rapids, etc. The focus of our work is the numerical simulation of the entrainment phenomenon associated with laminar plunging jets. With increasing jet velocity, the interfacial cusp formed between the jet and the liquid pool becomes sharper. At a critical jet velocity, entrainment inception occurs, i.e., the interfacial cusp breaks, the interface ruptures, and air is pulled into the liquid pool. We conduct two-fluid simulations using the Volume-Of-Fluid (VOF) methodology. The large range of length scales in the flow presents a major computational challenge. We postulate an approach based on scaling of the underlying physics and this helps alleviate the constraints that the physics poses on the numerical method. The approach is validated using a simple flow configuration - a cylinder rotating at an interface between two fluids. Our simulations capture the sharpening of the interfacial cusp, and the sudden rupture of the interface. The predicted critical entrainment velocities are within 1% of experimental data, thereby providing confidence in the approach. This work was supported by the UC Simulation Center at the University of Cincinnati.

  2. Admixture as the basis for genetic mapping

    OpenAIRE

    Buerkle, C. Alex; Lexer, Christian

    2008-01-01

    Genetic mapping in natural populations is increasing rapidly in feasibility and accessibility. As with many areas in genetics, advances in molecular techniques and statistics are drastically altering how we can investigate inheritance in wild organisms. For ecology and evolution, this is particularly significant and promising, because many of the organisms of interest are not amenable to conventional genetic approaches. Admixture mapping falls within a family of statistical approaches that us...

  3. Rapid-1 Hardening Accelerator Concrete Admixture

    OpenAIRE

    ECT Team, Purdue

    2007-01-01

    SIKA Rapid-1 is a concrete admixture that allows the development of very early high strengths in concrete consisting of commonly used mix components. Unlike concrete set accelerators, it does not reduce set time or long-term strength, and it does not corrode steel reinforcing. This hardening accelerator allows placement of fresh concrete without early stiffening, followed by a period of very rapid strength gain after initial set.

  4. The Stochastic Parcel Model: A deterministic parameterization of stochastically entraining convection

    Science.gov (United States)

    Romps, David M.

    2016-03-01

    Convective entrainment is a process that is poorly represented in existing convective parameterizations. By many estimates, convective entrainment is the leading source of error in global climate models. As a potential remedy, an Eulerian implementation of the Stochastic Parcel Model (SPM) is presented here as a convective parameterization that treats entrainment in a physically realistic and computationally efficient way. Drawing on evidence that convecting clouds comprise air parcels subject to Poisson-process entrainment events, the SPM calculates the deterministic limit of an infinite number of such parcels. For computational efficiency, the SPM groups parcels at each height by their purity, which is a measure of their total entrainment up to that height. This reduces the calculation of convective fluxes to a sequence of matrix multiplications. The SPM is implemented in a single-column model and compared with a large-eddy simulation of deep convection.

  5. Entrainment by the jet in HH 47

    Science.gov (United States)

    Raymond, John C.; Morse, Jon A.; Hartigan, P.; Curiel, S.; Heathcote, Steve

    1994-01-01

    Fabry-Perot images of the HH 47 optical jet show that the velocity decreases from the center toward the edges which is interpreted as evidence for entrainment. Those images can be used to investigate the rate of entrainment required to account for the observed luminosity. Entrainment along the jet can account for only small fractions of the jet mass and the molecular outflow seen in CO. We compare the density, excitation, and velocity structure of the jet with the predictions of viscous entrainment models and models of entrainment by expulsion of jet material by internal shocks, and find that either type of model can explain the general features.

  6. Entrainment in electrohydrodynamic heat pipes

    Science.gov (United States)

    Jones, T. B.; Perry, M. P.

    1972-01-01

    A theoretical analysis for predicting the onset of the Kelvin-Helmholtz instability is reported. The model for the analysis is described, and the derived stability criterion are given. It is concluded that surface tension plays a role in the entrainment limit of electro hydrodynamic heat pipes. The surface of the liquid in an EHD flow structure is open, with no restriction placed on the wavenumbers of perturbations.

  7. Effect of water-repellent admixtures on the behaviour of aerial lime-based mortars

    OpenAIRE

    Izaguirre, A.; Lanas, J.; Alvarez, J I

    2009-01-01

    Two different anionic surfactants, sodium oleate and calcium stearate, commercialized as water repellents for cement-based mortars, were added to lime-based mortars in order to check whether they were improved by these admixtures. Different properties of lime-based mortars were evaluated: fresh state behaviour through water retention, air content and setting time, hardened state properties such as density, water absorption through capillarity, water vapour permeability, long-term compressive ...

  8. THEORETICAL AND EXPERIMENTAL INVESTIGATIONS OF ENTRAINED AND TRANSPORTED CHARACTERISTICS OF SUBMERGED JET

    Institute of Scientific and Technical Information of China (English)

    DONG Zhi-yong; WU Chi-gong; YANG YONG-quan

    2004-01-01

    This paper presents entrainment mechanism,and transported and diffusion characteristics at the point of entry of submerged jet. The profiles of both velocity and concentration within the air-water mixing layer were theoretically deduced. And the comparisons between theoretical values and measured data were made. Results show that the velocity profile within the air-water mixing layer exhibits a form of error function. The concentrations of air entrainment in the internal and external regions of air-water mixing layer correspond to Gaussian distribution.

  9. A model study of mixing and entrainment in the horizontally evolving atmospheric convective boundary layer

    Energy Technology Data Exchange (ETDEWEB)

    Fedorovich, E.; Kaiser, R. [Univ. Karlsruhe, Inst. fuer Hydrologie und Wasserwirtschaft (Germany)

    1997-10-01

    We present results from a parallel wind-tunnel/large-eddy simulation (LES) model study of mixing and entrainment in the atmospheric convective boundary layer (CBL) longitudinally developing over a heated surface. The advection-type entrainment of warmer air from upper turbulence-free layers into the growing CBL has been investigated. Most of numerical and laboratory model studies of the CBL carried out so far dealt with another type of entrainment, namely the non-steady one, regarding the CBL growth as a non-stationary process. In the atmosphere, both types of the CBL development can take place, often being superimposed. (au)

  10. DCH dispersal and entrainment experiment in a scaled annular cavity

    International Nuclear Information System (INIS)

    The objective of this experiment was to measure the amount of corium dispersal and the droplet size distribution during high pressure melt ejection from a CE reactor. The melt and the steam flowed to the containment through a narrow annular cavity. The experiment was carried out on a 1/20th scaled model of the cavity and the containment. The scaling was based on dimensionless numbers obtained from a two-phase flow model of the dispersal and entrainment mechanisms in the cavity. Furthermore, the model shows that the flow in the cavity was choked, so high levels of dispersal and entrainment were possible. The experiment consisted of air-water, air-helium, air-woods metal and helium-woods metal tests; the main result being that the level of dispersal was very high in all cases. The woods metal data supported a separated flow model in the cavity, implying that the gas choked velocity was very high and the droplets very small. In contrast, the measured drop sizes for the water tests were much larger than the separated flow model predictions. This discrepancy could not be resolved because the entrainment mechanism is not properly understood at the present time. (orig.)

  11. Entrainment and mixing in vertical buoyant light-gas plumes

    International Nuclear Information System (INIS)

    Hydrogen has great potential as a future fuel because of its nearly pollution-free combustion. However, it is highly diffusive and can easily leak through joints, cracks and defective valves if care is not taken. Accidental release of hydrogen into surrounding air and its subsequent mixing are of concern in evaluating the safe transport of hydrogen in buildings through piping. Hydrogen release into air is of importance in nuclear reactor safety analysis also. During certain postulated accidents in nuclear reactors, hydrogen may be produced by high temperature metal-steam reactions and released into the containment building. A simple model is developed to determine the entrainment coefficient and the spread of a light-gas plume in a quiescent atmosphere. Experiments performed with low velocity salt water/fresh-water and helium-in-air jets indicate that buoyant gas plumes spread significantly faster than thermal plumes. The calculated effluent concentrations are in excellent agreement with those measured when an entrainment coefficient of 0.15 is used in the plume equations. This is significantly higher than the entrainment coefficients of 0.075 to 0.093 reported for thermal plumes

  12. Elements-admixtures of fluorite. Research technique

    International Nuclear Information System (INIS)

    Present article is devoted to elements-admixtures of fluorite and research techniques used. As a material for researches the mono mineral samples of fluorite of various geologic deposits and ores were used. The determination of sodium and potassium was conducted by means of flame photometry. Strontium, uranium, thorium, lead and rubidium were determined by means of quantitative X-ray spectroscopic analysis. The barium analysis was conducted by means of quantitative method. The manganese analysis was conducted by means of electron paramagnetic resonance.

  13. Numerical study of radiatively induced entrainment

    International Nuclear Information System (INIS)

    Numerical simulations using the one-dimensional turbulence (ODT) model are compared to water-tank measurements emulating convection and entrainment in stratiform clouds driven by cloud-top cooling. Measured dependences of the entrainment rate on Richardson number are reproduced. An additional parameter variation suggests more complicated dependences of the entrainment rate than previously anticipated. Uncertainties in the modeling assumptions and in the experimental results are discussed.

  14. Admixture, Population Structure, and F-Statistics.

    Science.gov (United States)

    Peter, Benjamin M

    2016-04-01

    Many questions about human genetic history can be addressed by examining the patterns of shared genetic variation between sets of populations. A useful methodological framework for this purpose isF-statistics that measure shared genetic drift between sets of two, three, and four populations and can be used to test simple and complex hypotheses about admixture between populations. This article provides context from phylogenetic and population genetic theory. I review howF-statistics can be interpreted as branch lengths or paths and derive new interpretations, using coalescent theory. I further show that the admixture tests can be interpreted as testing general properties of phylogenies, allowing extension of some ideas applications to arbitrary phylogenetic trees. The new results are used to investigate the behavior of the statistics under different models of population structure and show how population substructure complicates inference. The results lead to simplified estimators in many cases, and I recommend to replaceF3with the average number of pairwise differences for estimating population divergence. PMID:26857625

  15. Partial entrainment of gravel bars during floods

    Science.gov (United States)

    Konrad, C.P.; Booth, D.B.; Burges, S.J.; Montgomery, D.R.

    2002-01-01

    Spatial patterns of bed material entrainment by floods were documented at seven gravel bars using arrays of metal washers (bed tags) placed in the streambed. The observed patterns were used to test a general stochastic model that bed material entrainment is a spatially independent, random process where the probability of entrainment is uniform over a gravel bar and a function of the peak dimensionless shear stress ??*0 of the flood. The fraction of tags missing from a gravel bar during a flood, or partial entrainment, had an approximately normal distribution with respect to ??*0 with a mean value (50% of the tags entrained) of 0.085 and standard deviation of 0.022 (root-mean-square error of 0.09). Variation in partial entrainment for a given ??*0 demonstrated the effects of flow conditioning on bed strength, with lower values of partial entrainment after intermediate magnitude floods (0.065 entrainment was approximately uniform over a gravel bar during individual floods and independent from flood to flood, regions of preferential stability and instability emerged at some bars over the course of a wet season. Deviations from spatially uniform and independent bed material entrainment were most pronounced for reaches with varied flow and in consecutive floods with small to intermediate magnitudes.

  16. Quantifying entrainment in pyroclastic density currents from the Tungurahua eruption, Ecuador: Integrating field proxies with numerical simulations

    Science.gov (United States)

    Benage, M. C.; Dufek, J.; Mothes, P. A.

    2016-07-01

    The entrainment of air into pyroclastic density currents (PDCs) impacts the dynamics and thermal history of these highly mobile currents. However, direct measurement of entrainment in PDCs is hampered due to hazardous conditions and opaqueness of these flows. We combine three-dimensional multiphase Eulerian-Eulerian-Lagrangian calculations with proxies of thermal conditions preserved in deposits to quantify air entrainment in PDCs at Tungurahua volcano, Ecuador. We conclude that small-volume PDCs develop a particle concentration gradient that results in disparate thermal characteristics for the concentrated bed load (>600 to ~800 K) and the overlying dilute suspended load (~300-600 K). The dilute suspended load has effective entrainment coefficients 2-3 times larger than the bed load. This investigation reveals a dichotomy in entrainment and thermal history between two regions in the current and provides a mechanism to interpret the depositional thermal characteristics of small-volume but frequently occurring PDCs.

  17. Entrainment instability and vertical motion as causes of stratocumulus breakup

    Science.gov (United States)

    Weaver, C. J.; Pearson, R., Jr.

    1990-01-01

    Entrainment instability is thought to be a cause of stratocumulus breakup. At the interface between the cloud and the overlying air, mixtures may form which are negatively buoyant because of cloud droplet evaporation. Quantities devised to predict breakup are obtained from aircraft observations and are tested against cloud observations from satellite. Often, the parameters indicate that breakup should occur but the clouds remain, sometimes for several days. One possible explanation for breakup is vertical motion from passing synoptic cyclones. Several cases suggest that breakup is associated with the downward vertical motion from the cold air advected behind an eastward moving cyclone.

  18. Liquid entrainment by an expanding core disruptive accident bubble--a Kelvin/Helmholtz phenomenon

    International Nuclear Information System (INIS)

    The final stage of a postulated energetic core disruptive accident (CDA) in a liquid metal fast breeder reactor is believed to involve the expansion of a high-pressure core-material bubble against the overlying pool of sodium. Some of the sodium will be entrained by the CDA bubble which may influence the mechanical energy available for damage to the reactor vessel. The following considerations of liquid surface instability indicate that the Kelvin-Helmholtz (K-H) mechanism is primarily responsible for liquid entrainment by the expanding CDA bubble. First, an instability analysis is presented which shows that the K-H mechanism is faster than the Taylor acceleration mechanism of entrainment at the high fluid velocities expected within the interior of the expanding CDA bubble. Secondly, a new model of liquid entrainment by the CDA bubble is introduced which is based on spherical-core-vortex motion and entrainment via the K-H instability along the bubble surface. The model is in agreement with new experimental results presented here on the reduction of nitrogen-gas-simulant CDA bubble work potential. Finally, a one-dimensional air-over-water parallel flow experiment was undertaken which demonstrates that the K-H instability results in sufficiently rapid and fine liquid atomization to account for observed CDA gas-bubble work reductions. An important byproduct of the theoretical and experimental work is that the liquid entrainment rate is well described by the Ricou-Spalding entrainment law

  19. Flow characteristics in a rectangular vessel due to gas entrainment

    International Nuclear Information System (INIS)

    The authors investigated hydrodynamic factors to cause the gas entrainment from the surface of coolant flowing in a reactor vessel. The flow characteristics were established for the water flow, which is fed into a three-dimensional rectangular cell that represents the flow field in a reactor. Existence of predominant types of flow, such as the colliding flow, circulating flow and vertical eddy, were established by results of measurement on the distribution of flow velocity. The steady state three-dimensional flow in the flow field was also demonstrated. Difference in the flow velocity between area at the center of water tank and near the side wall of it and momentary variation of three-dimensional flow velocity near the water surface were also found. It was concluded from these results that the air entrainment is caused by the interference between the steady state circulating flow and momentary and local variation of flow velocity. (author)

  20. RESEARCH ON EARLY STRENGTH AND FREEZE-PROOF RESISTANCE OF AIR-ENTRAINED CONCRETE UNDER 3 ℃CURING%3℃养护下引气混凝土早期强度及抗冻性能研究

    Institute of Scientific and Technical Information of China (English)

    张凯; 王起才; 王庆石; 李盛; 李建新

    2015-01-01

    采用强度试验、压汞法、气孔分析法、快速冻融法,以低温(3±0.2)℃养护下引气混凝土为研究对象,对混凝土的强度、孔隙结构及抗冻耐久性进行了研究。结果表明:在3℃养护下,随着含气量的提高,孔径均匀分布,显著改善了混凝土的内部孔隙结构,但比标准养护条件下同等含气量混凝土的孔结构粗化。为更好地阐述混凝土实际强度受含气量的影响,由孔隙结构可进一步推算出3℃养护下混凝土的实际抗压强度,并与标准养护条件下实际抗压强度对比,显示两者之间的不同。%The strength, the pore structure and freeze-proof durability of air-entrained concrete under 3 ℃temperature curing and with different air contents were researched by taking air-entrained concrete under low temperature curing (3 ±0.2 ) ℃ as the object, adopting strength test mercury intrusion method, pore analytical method and fast freeze-thaw method.The results showed that when concrete of 3 ℃ temperature curing, as the air content was increased, the distribution of pore diameter was uniform and the interior pore structure of concrete was improved significantly, however, the pore structure under the room curing at the same air content of concrete was lower than under 3 ℃curing.In order to expound the influence of air content on the actual concrete strength in an even better fashion, the concrete compressive strength under 3 ℃curing can further be estimated by pore structure, which was compared with the room curing actual compressive strength, showing the difference between the two.

  1. Timescales of Massive Human Entrainment

    DEFF Research Database (Denmark)

    Fusaroli, Riccardo; Perlman, Marcus; Mislove, Alan;

    2014-01-01

    distinct scales, in an exquisitely time locked fashion. Using a large scale database of human communication data, we analyze and describe three different time scales of human entrainment in electronic media. We sought a distinct shared experience that provided a test bed for quantifying large scale human...... debate on human attention. We show that social behavior covaries second by second to the interactional dynamics of the debates: A candidate speaking induces rapid increases in mentions of his name on social media and decreases in mentions of the other candidate. Moreover, interruptions by an interlocutor...... increase the attention received. We also highlight a distinct time scale for the impact of salient moments in the debate: Mentions in social media start within 5 to 10 seconds after the moment; peak at approximately one minute; and slowly decay in a consistent fashion across well known events during the...

  2. The entrainment rate for a row of turbulent jets. M.S. Thesis Final Report

    Science.gov (United States)

    Gordon, Eliott B.; Greber, Isaac

    1990-01-01

    Entrainment rates for a row of isothermal circular air jets issuing into a quiescent environment are found by integrating velocity distributions measured by a linearized hot-wire anemometer. Jet spacing to jet diameter ratios of 2.5, 5, 10, and 20 are studied at jet Reynold's numbers ranging from 5110 to 12070. Velocity distributions are determined at regular downstream intervals at axial distances equal to 16.4 to 164 jet diameters from the jet source. The entrainment rates for the four spacing configurations vary monotonically with increasing spacing/diameter between the limiting case of the slot jet entrainment rate (where the jet spacing to diameter ratio is zero) and the circular jet entrainment rate (in which the spacing to diameter ratio is infinity).

  3. Entrainment of soluble and non soluble tracers from a boiling water surface

    International Nuclear Information System (INIS)

    The entrainment of droplets containing solid or soluble fission product simulants from the surface of a boiling water pool into a gas atmosphere was investigated at conditions, which are relevant to a severe core melt scenario. Different air-steam ratios and at pressures (2-6 bar) were considered in the model containment. Measurements carried out far above the air-liquid interface are compared with the predictions of existing correlations. Favorable agreement is obtained with the correlation of Kataoka and Ishii [Int. J. Heat Mass Transf. 27 (1984)] for the entrainment of soluble fission products into an air-steam atmosphere. Results from integral measurements however suggest that improved correlations should be based on the Froude, Weber and Rayleigh numbers, and separate between entrainment and sedimentation

  4. Temperature compensation and entrainment in circadian rhythms

    International Nuclear Information System (INIS)

    To anticipate daily variations in the environment and coordinate biological activities into a daily cycle many organisms possess a circadian clock. In the absence of external time cues the circadian rhythm persists with a period of approximately 24 h. The clock phase can be shifted by single pulses of light, darkness, chemicals, or temperature and this allows entrainment of the clock to exactly 24 h by cycles of these zeitgebers. On the other hand, the period of the circadian rhythm is kept relatively constant within a physiological range of constant temperatures, which means that the oscillator is temperature compensated. The mechanisms behind temperature compensation and temperature entrainment are not fully understood, neither biochemically nor mathematically. Here, we theoretically investigate the interplay of temperature compensation and entrainment in general oscillatory systems. We first give an analytical treatment for small temperature shifts and derive that every temperature-compensated oscillator is entrainable to external small-amplitude temperature cycles. Temperature compensation ensures that this entrainment region is always centered at the endogenous period regardless of possible seasonal temperature differences. Moreover, for small temperature cycles the entrainment region of the oscillator is potentially larger for rectangular pulses. For large temperature shifts we numerically analyze different circadian clock models proposed in the literature with respect to these properties. We observe that for such large temperature shifts sinusoidal or gradual temperature cycles allow a larger entrainment region than rectangular cycles. (paper)

  5. Experimental demonstration of gas entrainment into liquid metals

    International Nuclear Information System (INIS)

    Entrainment of cover gas into the liquid metal coolant is one of the essential safety issues in the design of innovative liquid metal-cooled fast reactors. We present experimental studies of this phenomenon in low-melting metals. Ultrasonic and X-ray were considered as diagnostic tools for a visualization of gas entrainment at the free surface of the melt. Laboratory experiments were conducted using the eutectic alloy GaInSn which is liquid at room temperature. The vortex activated entrainment of air at the free surface of a rotating flow was disclosed by means of ultrasonic techniques. The X-ray radioscopy was used to visualize the behaviour of Argon bubbles inside a slit geometry. The measurements reveal distinct differences between water and GaInSn especially with respect to the process of bubble formation, the coalescence and the breakup of bubbles. Our results emphasize the importance of liquid metal experiments which are able to provide a suitable data base for numerical code validation. (author)

  6. On the modelling of bubble entrainment by impinging jets in CFD-simulations

    International Nuclear Information System (INIS)

    This contribution presents different approaches for the modeling of air entrainment under water by plunging jets in CFD codes. In simulations which include the full length of the jet and its environment, the process of bubble generation cannot be resolved due to computational limitations. This is why the air entrainment has to be modeled in meso-scale simulations. In the frame of an Euler- Euler simulation, the local morphology of the phases has to be considered in the drag model. In the impinging jet configuration, the air is a continuous phase above the water level but bubbly below the water level. Various drag models are implemented in the CFD solver CFX11 and their influence on the gas void fraction below the water level is discussed. The algebraic interface area density (AIAD) model applies a drag coefficient for bubbles and a different drag coefficient for the free surface. If the AIAD model is used for the simulation of impinging jets, the gas entrainment depends on the free parameters included in this model. The calculated gas entrainment can be adapted via these parameters. Therefore, an advanced AIAD approach could be used in future for the implementation of models (e.g. correlations) for the gas entrainment. (authors)

  7. High-Performance Grouting Mortar Based on Mineral Admixtures

    OpenAIRE

    2015-01-01

    A study on high-performance grouting mortar is reported. The common mortar was modified by mineral admixtures such as gypsum, bauxite, and alunite. The effects of mineral admixtures on the fluidity, setting time, expansion, strength, and other properties of mortar were evaluated experimentally. The microstructure of the modified mortar was characterized by X-ray diffraction, scanning electron microscopy, and mercury intrusion porosimetry. Moreover, the expansive performance and strength of th...

  8. Geographic patterns of genome admixture in Latin American Mestizos.

    Directory of Open Access Journals (Sweden)

    Sijia Wang

    2008-03-01

    Full Text Available The large and diverse population of Latin America is potentially a powerful resource for elucidating the genetic basis of complex traits through admixture mapping. However, no genome-wide characterization of admixture across Latin America has yet been attempted. Here, we report an analysis of admixture in thirteen Mestizo populations (i.e. in regions of mainly European and Native settlement from seven countries in Latin America based on data for 678 autosomal and 29 X-chromosome microsatellites. We found extensive variation in Native American and European ancestry (and generally low levels of African ancestry among populations and individuals, and evidence that admixture across Latin America has often involved predominantly European men and both Native and African women. An admixture analysis allowing for Native American population subdivision revealed a differentiation of the Native American ancestry amongst Mestizos. This observation is consistent with the genetic structure of pre-Columbian populations and with admixture having involved Natives from the area where the Mestizo examined are located. Our findings agree with available information on the demographic history of Latin America and have a number of implications for the design of association studies in population from the region.

  9. Washing of the AN-107 entrained solids

    International Nuclear Information System (INIS)

    This report describes the results of a test conducted by Battelle to assess the effects of inhibited water washing on the composition of the entrained solids in the diluted AN-107 low-activity waste (LAW) sample. The objective of this work was to gather data on the solubility of the AN-107 entrained solids in 0.01 M NaOH, so that BNFL can evaluate whether these solids require caustic leaching

  10. Washing of the AN-107 entrained solids

    Energy Technology Data Exchange (ETDEWEB)

    GJ Lumetta; FV Hoopes

    2000-03-31

    This report describes the results of a test conducted by Battelle to assess the effects of inhibited water washing on the composition of the entrained solids in the diluted AN-107 low-activity waste (LAW) sample. The objective of this work was to gather data on the solubility of the AN-107 entrained solids in 0.01 M NaOH, so that BNFL can evaluate whether these solids require caustic leaching.

  11. In situ absolute air, O3 and NO densities in the effluent of a cold RF argon atmospheric pressure plasma jet obtained by molecular beam mass spectrometry

    International Nuclear Information System (INIS)

    A molecular beam mass spectrometer has been calibrated and used to measure the air entrainment, nitric oxide and ozone concentrations in the effluent of a cold atmospheric pressure argon RF driven plasma jet. The approaches for calibrating the mass spectrometer for different species are described in detail. Gas phase densities of ozone and nitric oxide up to 7.5 ppm and 4 ppm, respectively, have been measured in the far effluent of the argon plasma jet. The difference in air entrainment when the plasma is undisturbed or is close to a well, which is the case for e.g. in vitro plasma–cell interaction studies, is shown. In addition, an exponential decay of the positive ion flux as a function of distance in the effluent is obtained. Furthermore, the effect of plasma power, duty cycle and air and O2 admixtures introduced into the argon flow on the NO and O3 production is presented, including the possibility of independent control of the NO and O3 flux from the jet. (paper)

  12. In situ absolute air, O3 and NO densities in the effluent of a cold RF argon atmospheric pressure plasma jet obtained by molecular beam mass spectrometry

    Science.gov (United States)

    van Ham, B. T. J.; Hofmann, S.; Brandenburg, R.; Bruggeman, P. J.

    2014-06-01

    A molecular beam mass spectrometer has been calibrated and used to measure the air entrainment, nitric oxide and ozone concentrations in the effluent of a cold atmospheric pressure argon RF driven plasma jet. The approaches for calibrating the mass spectrometer for different species are described in detail. Gas phase densities of ozone and nitric oxide up to 7.5 ppm and 4 ppm, respectively, have been measured in the far effluent of the argon plasma jet. The difference in air entrainment when the plasma is undisturbed or is close to a well, which is the case for e.g. in vitro plasma-cell interaction studies, is shown. In addition, an exponential decay of the positive ion flux as a function of distance in the effluent is obtained. Furthermore, the effect of plasma power, duty cycle and air and O2 admixtures introduced into the argon flow on the NO and O3 production is presented, including the possibility of independent control of the NO and O3 flux from the jet.

  13. Entrainment, Drizzle, and Cloud Albedo

    Science.gov (United States)

    Ackerman, A. S.; Kirkpatrick, J. P.; Stevens, D. E.; Toon, O. B.

    2004-01-01

    Increased aerosol and hence droplet concentrations in polluted clouds are expected to inhibit precipitation and thereby increase cloud water, leading to more reflective clouds that partially offset global warming. Yet polluted clouds are not generally observed to hold more water. Much of the uncertainty regarding the indirect aerosol effect stems from inadequate understanding of such changes in cloud water. Detailed simulations show that the relative humidity of air overlying stratocumulus is a leading factor determining whether cloud water increases or decreases when precipitation is suppressed. When the overlying air is dry, cloud water can decrease as droplet concentrations increase.

  14. Annular flow entrainment rate experiment in a small vertical pipe

    International Nuclear Information System (INIS)

    Two-fluid model predictions of film dryout in annular flow, leading to nuclear reactor fuel failure, are limited by the uncertainties in the constitutive relations for the entrainment rate of droplets from the liquid film. The main cause of these uncertainties is the lack of separate-effects experimental data in the range of the operating conditions in nuclear power reactors. An air-water experiment has been performed to measure the entrainment rate in a small pipe. The current data extend the available database in the literature to higher gas and liquid flows and also to higher pressures. The measurements were made with the film extraction technique. A mechanistic model was obtained based on Kelvin-Helmholtz' instability theory. The dimensionless model includes the Weber number of the gas and the liquid film Reynolds number. Kataoka and Ishii's correlation (Kataoka, I., Ishii, M., (1982)) is modified based on this model and the new data. The new correlation collapses the present air-water data and Cousins and Hewitt's data (Cousins, L.B. (1968)) The effects of pressure and surface tension were considered in the derivation so it may be applied for boiling water reactor operating conditions. (orig.)

  15. Entrainment and the cranial rhythmic impulse.

    Science.gov (United States)

    McPartland, J M; Mein, E A

    1997-01-01

    Entrainment is the integration or harmonization of oscillators. All organisms pulsate with myriad electrical and mechanical rhythms. Many of these rhythms emanate from synchronized pulsating cells (eg, pacemaker cells, cortical neurons). The cranial rhythmic impulse is an oscillation recognized by many bodywork practitioners, but the functional origin of this impulse remains uncertain. We propose that the cranial rhythmic impulse is the palpable perception of entrainment, a harmonic frequency that incorporates the rhythms of multiple biological oscillators. It is derived primarily from signals between the sympathetic and parasympathetic nervous systems. Entrainment also arises between organisms. The harmonizing of coupled oscillators into a single, dominant frequency is called frequency-selective entrainment. We propose that this phenomenon is the modus operandi of practitioners who use the cranial rhythmic impulse in craniosacral treatment. Dominant entrainment is enhanced by "centering," a technique practiced by many healers, for example, practitioners of Chinese, Tibetan, and Ayurvedic medicine. We explore the connections between centering, the cranial rhythmic impulse, and craniosacral treatment. PMID:8997803

  16. Nonphotic entrainment of the human circadian pacemaker

    Science.gov (United States)

    Klerman, E. B.; Rimmer, D. W.; Dijk, D. J.; Kronauer, R. E.; Rizzo, J. F. 3rd; Czeisler, C. A.

    1998-01-01

    In organisms as diverse as single-celled algae and humans, light is the primary stimulus mediating entrainment of the circadian biological clock. Reports that some totally blind individuals appear entrained to the 24-h day have suggested that nonphotic stimuli may also be effective circadian synchronizers in humans, although the nonphotic stimuli are probably comparatively weak synchronizers, because the circadian rhythms of many totally blind individuals "free run" even when they maintain a 24-h activity-rest schedule. To investigate entrainment by nonphotic synchronizers, we studied the endogenous circadian melatonin and core body temperature rhythms of 15 totally blind subjects who lacked conscious light perception and exhibited no suppression of plasma melatonin in response to ocular bright-light exposure. Nine of these fifteen blind individuals were able to maintain synchronization to the 24-h day, albeit often at an atypical phase angle of entrainment. Nonphotic stimuli also synchronized the endogenous circadian rhythms of a totally blind individual to a non-24-h schedule while living in constant near darkness. We conclude that nonphotic stimuli can entrain the human circadian pacemaker in some individuals lacking ocular circadian photoreception.

  17. Effect of entrained liquid on turbulent mixing rate between subchannels in annular two-phase flows

    International Nuclear Information System (INIS)

    Turbulent mixing rates of gas and liquid phases between the subchannels have been measured for various air-water two-phase annular flows in a multiple channel consisting of the two identical circular subchannels. In order to study effect of entrained liquid in the gas core on the turbulent mixing rates, experiments were conducted for two types of liquid injection method, i.e., a small bore nozzle placed in the subchannel center and a porous wall, at a fixed gas injection method. The result showed that the effect of entrained liquid on the turbulent mixing rates of both phases is negligibly small. (author)

  18. Resonant entrainment of a confined pulsed jet

    Science.gov (United States)

    Parikh, P. G.; Moffat, R. J.

    1982-01-01

    This paper reports the discovery of a new resonant entrainment phenomenon associated with a confined, pulsed jet flow. It was found that a confined jet, when pulsed at an organ-pipe resonant frequency of the confinement tube, experiences greatly enhanced entrainment and mixing near the exit end of the confinement tube compared to a steady confined jet. The mixing and entrainment rates for the resonantly pulsed confined jet approach, and in some cases slightly exceed, those for an unconfined pulsed jet. Both visual and quantitative evidence of this phenomenon is presented. The new effect should be of considerable interest in ejector and combustor design, both of which benefit from any enhancement in mixing between a primary and a secondary flow

  19. Observational estimates of detrainment and entrainment in non-precipitating shallow cumulus

    Science.gov (United States)

    Norgren, M. S.; Small, J. D.; Jonsson, H. H.; Chuang, P. Y.

    2016-01-01

    Vertical transport associated with cumulus clouds is important to the redistribution of gases, particles, and energy, with subsequent consequences for many aspects of the climate system. Previous studies have suggested that detrainment from clouds can be comparable to the updraft mass flux, and thus represents an important contribution to vertical transport. In this study, we describe a new method to deduce the amounts of gross detrainment and entrainment experienced by non-precipitating cumulus clouds using aircraft observations. The method utilizes equations for three conserved variables: cloud mass, total water, and moist static energy. Optimizing these three equations leads to estimates of the mass fractions of adiabatic mixed-layer air, entrained air and detrained air that the sampled cloud has experienced. The method is applied to six flights of the CIRPAS Twin Otter during the Gulf of Mexico Atmospheric Composition and Climate Study (GoMACCS) which took place in the Houston, Texas region during the summer of 2006 during which 176 small, non-precipitating cumuli were sampled. Using our novel method, we find that, on average, these clouds were comprised of 30 to 70 % mixed-layer air, with entrained air comprising most of the remainder. The mass fraction of detrained air was usually very small, less than 2 %, although values larger than 10 % were found in 15 % of clouds. Entrained and detrained air mass fractions both increased with altitude, consistent with some previous observational studies. The largest detrainment events were almost all associated with air that was at their level of neutral buoyancy, which has been hypothesized in previous modeling studies. This new method could be readily used with data from other previous aircraft campaigns to expand our understanding of detrainment for a variety of cloud systems.

  20. Learning with Admixture: Modeling, Optimization, and Applications in Population Genetics

    DEFF Research Database (Denmark)

    Cheng, Jade Yu

    2016-01-01

    including population splits, effective population sizes, gene flow, etc. Since joining the CoalHMM development team in 2014, I have mainly contributed in two directions: 1) improving optimizations through heuristic-based evolutionary algorithms and 2) modeling of historical admixture events. Ohana, meaning...... data. Ohana's admixture module is based on classical structure modeling but uses new optimization subroutines through quadratic programming, which outperform the current state-of-the-art software in both speed and accuracy. Ohana presents a new method for phylogenetic tree inference using Gaussian...

  1. Gas entrainment inception at the border of a flow-swollen liquid surface

    International Nuclear Information System (INIS)

    A rapid liquid flow into a tank may impinge on the free surface, making it swell partially. The returning flow branches off from the free surface and re-submerges at the border of the swollen surface. If the flow velocity along the swollen surface is high enough, gas bubbles are formed at the border and entrained by the liquid flow. The conditions necessary for gas entrainment in a simple system are examined experimentally, using water and air as working fluids. The effect of surface tension is examined by adding a surface active agent to the water. The results show that gas entrainment inception is determined by the flow pattern in the system and the product of the Froude and Weber numbers based on the local velocity at the bubble formation point. (orig.)

  2. Removal of PCDDs/Fs from municipal solid waste incineration by entrained-flow adsorption technology

    Institute of Scientific and Technical Information of China (English)

    YAN Jian-hua; PENG Zheng; LU Sheng-yong; LI Xiao-dong; CEN Ke-fa

    2006-01-01

    Entrained flow adsorption using activated carbon as the adsorbent is widely adopted for PCDDs/Fs-abatement in municipal solidwaste incineration (MSWI) process. The effects of operating parameters including flue gas temperature, feeding rate of activated carbon, polychlorinated dibenzodioxins and polychlorinated dibenzofurans (PCDDs/Fs) concentration at the inlet of the air pollution control device (APCD), filter materials, pressure drop on PCDDs/Fs removal efficiency are reviewed and commented upon in this paper. Evaluation on the various mechanistic models for entrained flow adsorption is carried out based on the computational simulation in terms of the actual operating condition and theoretical analysis. Finally, an advancement of entrained flow adsorption in combination of dual bag filter is introduced.

  3. Entrainment rate of droplets in the ripple-annular regime for small vertical tubes

    International Nuclear Information System (INIS)

    Two-fluid model predictions of film dryout in annular flow are limited by the uncertainties in the constitutive relations for the entrainment rate of droplets from the liquid film. The main cause of these uncertainties is the lack of separate effects experimental data in the range of the operating conditions in nuclear power reactors. Air/water and Freon-113 entrainment rate data have been obtained in 10 mm tubes using the film extraction technique. These experiments have been scaled to approach high pressure steam-water flow conditions. The effects of surface tension and density ratio, missing from most previous data sets, have been systematically tested. The entrainment rate mechanism is assumed to be a Kelvin-Helmholtz instability. Based on this analysis and two previous correlations, a new correlation is proposed that is valid for low viscosity fluids in small ducts in the ripple annular regime

  4. Relationships of Entrainment Rate with Dynamical and Thermodynamic Properties in Shallow Convection

    Science.gov (United States)

    Lu, C.; Liu, Y.; Zhang, G. J.; Wu, X.; Endo, S.; Cao, L.; Li, Y.; Guo, X.

    2015-12-01

    This work examines the relationships of entrainment rate to vertical velocity, buoyancy, turbulent dissipation rate by applying stepwise principal component regression to observational data from shallow cumulus clouds collected during the Routine AAF [Atmospheric Radiation Measurement (ARM) Aerial Facility] Clouds with Low Optical Water Depths (CLOWD) Optical Radiative Observations (RACORO) field campaign over the ARM Southern Great Plains (SGP) site near Lamont, Oklahoma. The cumulus clouds during the RACORO campaign simulated using a large eddy simulation (LES) model are also examined with the same approach. The analysis shows that combination of multiple variables can better represent entrainment rate in both the observations and LES than the single-variable fitting equations and the three commonly used parameterizations. A new parameterization is thus presented that relates entrainment rate to vertical velocity, buoyancy and dissipation rate; the effects of treating clouds as ensembles and humid shells surrounding cumulus clouds on the new parameterization are discussed. Physical mechanisms underlying the relationships of entrainment rate to vertical velocity, buoyancy and dissipation rate are also explored. Furthermore, the effects of relative humidity in the entrained dry air on the above relationships are discussed; a possible physical mechanism for the effects is explored.

  5. Impact of reduced near-field entrainment of overpressured volcanic jets on plume development

    Science.gov (United States)

    Saffaraval, Farhad; Solovitz, Stephen A.; Ogden, Darcy E.; Mastin, Larry G.

    2012-01-01

    Volcanic plumes are often studied using one-dimensional analytical models, which use an empirical entrainment ratio to close the equations. Although this ratio is typically treated as constant, its value near the vent is significantly reduced due to flow development and overpressured conditions. To improve the accuracy of these models, a series of experiments was performed using particle image velocimetry, a high-accuracy, full-field velocity measurement technique. Experiments considered a high-speed jet with Reynolds numbers up to 467,000 and exit pressures up to 2.93 times atmospheric. Exit gas densities were also varied from 0.18 to 1.4 times that of air. The measured velocity was integrated to determine entrainment directly. For jets with exit pressures near atmospheric, entrainment was approximately 30% less than the fully developed level at 20 diameters from the exit. At pressures nearly three times that of the atmosphere, entrainment was 60% less. These results were introduced into Plumeria, a one-dimensional plume model, to examine the impact of reduced entrainment. The maximum column height was only slightly modified, but the critical radius for collapse was significantly reduced, decreasing by nearly a factor of two at moderate eruptive pressures.

  6. Research and manufacture about high-activity small admixture in sprayed concrete

    Energy Technology Data Exchange (ETDEWEB)

    Fan, W.; Zhang, Z.; Zheng, Y. [Jiaozuo Institute of Technology, Jiaozuo (China)

    2000-04-01

    Two types of high-activity small admixture are researched and produced by using industrial wastes: (1) F-type high-activity small admixture; (2) K-type high-activity small admixture. If these high-activity small admixtures were used to replace 30 percent of cement, the strength of the sprayed concrete may be enhanced by about 20 percent. 1 ref., 7 tabs.

  7. Liquid Droplet Detachment and Entrainment in Microscale Flows

    Science.gov (United States)

    Hidrovo, Carlos

    2005-11-01

    In this talk we will present a first order study of liquid water detachment and entrainment into air flows in hydrophobic microchannels. Silicon based microstructures consisting of 23 mm long U-shaped channels of different geometry were used for this purpose. The structures are treated with a Molecular Vapor Deposition (MVD) process that renders them hydrophobic. Liquid water is injected through a side slot located 2/3 of the way downstream from the air channel inlet. The water entering the air channel beads up into slugs or droplets that grow in size at this injection location until they fill and flood the channel or are carried away by the air flow. The slugs/droplets dimensions at detachment are correlated against superficial gas velocity and proper dimensionless parameters are postulated and examined to compare hydrodynamic forces against surface tension. It is found that slug/droplet detachment is dominated by two main forces: pressure gradient drag, arising from confinement of a viscous flow in the channel, and inertial drag, arising from the stagnation of the air due to obstruction by the slugs/droplets. A detachment regime map is postulated based on the relative importance of these forces under different flow conditions.

  8. Washing of the AW-101 entrained solids

    International Nuclear Information System (INIS)

    BNFL Inc. (BNFL) is under contract with the US Department of Energy, River Protection Project (DOE-RPP) to design, construct, and operate facilities for treating wastes stored in the single-shell and double-shell tanks at the Hanford Site, Richland, Washington. The DOE-BNFL RPP contract identifies two feeds to the waste treatment plant: (1) primarily liquid low-activity waste (LAW) consisting of less than 2 wt% entrained solids and (2) high-level waste (HLW) consisting of 10 to 200 g/L solids slurry. This report describes the results of a test conducted by Battelle to assess the effects of inhibited water washing on the composition of the entrained solids in the diluted AW-101 low-activity waste (LAW) sample. The objective of this work was to gather data on the solubility of the AW-101 entrained solids in 0.01 M NaOH, so that BNFL can evaluate whether these solids require caustic leaching. The work was conducted according to test plan BNFL-TP-29953-9, Rev. 0, LAW Entrained Solids Water Wash and Caustic Leach Testing. The test went according to plan, with no deviations from the test plan. Based on the results of the 0.01 M NaOH washing, a decision was made by BNFL to not proceed with the caustic leaching test. The composition of the washed solids was such that caustic leaching would not result in significant reduction in the immobilized HLW volume

  9. Laminar Entrained Flow Reactor (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-02-01

    The Laminar Entrained Flow Reactor (LEFR) is a modular, lab scale, single-user reactor for the study of catalytic fast pyrolysis (CFP). This system can be employed to study a variety of reactor conditions for both in situ and ex situ CFP.

  10. North African populations carry the signature of admixture with Neandertals

    DEFF Research Database (Denmark)

    Sánchez-Quinto, Federico; Botigué, Laura R; Civit, Sergi;

    2012-01-01

    One of the main findings derived from the analysis of the Neandertal genome was the evidence for admixture between Neandertals and non-African modern humans. An alternative scenario is that the ancestral population of non-Africans was closer to Neandertals than to Africans because of ancient popu...

  11. A Spatial Framework for Understanding Population Structure and Admixture

    Science.gov (United States)

    Bradburd, Gideon S.; Ralph, Peter L.; Coop, Graham M.

    2016-01-01

    Geographic patterns of genetic variation within modern populations, produced by complex histories of migration, can be difficult to infer and visually summarize. A general consequence of geographically limited dispersal is that samples from nearby locations tend to be more closely related than samples from distant locations, and so genetic covariance often recapitulates geographic proximity. We use genome-wide polymorphism data to build “geogenetic maps,” which, when applied to stationary populations, produces a map of the geographic positions of the populations, but with distances distorted to reflect historical rates of gene flow. In the underlying model, allele frequency covariance is a decreasing function of geogenetic distance, and nonlocal gene flow such as admixture can be identified as anomalously strong covariance over long distances. This admixture is explicitly co-estimated and depicted as arrows, from the source of admixture to the recipient, on the geogenetic map. We demonstrate the utility of this method on a circum-Tibetan sampling of the greenish warbler (Phylloscopus trochiloides), in which we find evidence for gene flow between the adjacent, terminal populations of the ring species. We also analyze a global sampling of human populations, for which we largely recover the geography of the sampling, with support for significant histories of admixture in many samples. This new tool for understanding and visualizing patterns of population structure is implemented in a Bayesian framework in the program SpaceMix. PMID:26771578

  12. Performance of entrained flow and fluidised bed biomass gasifiers on different scales

    International Nuclear Information System (INIS)

    Highlights: ► Gasification of biomass in fluidised bed and entrained flow reactors is modelled. ► The systems are evaluated for a thermal input from 10 MW to 500 MW. ► Special attention is given to the preconditioning methods for biomass. ► Fluidised bed and entrained flow gasifiers are compared in terms of efficiency and costs. - Abstract: This biomass gasification process study compares the energetic and economic efficiencies of a dual fluidised bed and an oxygen-blown entrained flow gasifier from 10 MWth to 500 MWth. While fluidised bed gasification became the most applied technology for biomass in small and medium scale facilities, entrained flow gasification technology is still used exclusively for industrial scale coal gasification. Therefore, it is analysed whether and for which capacity the entrained flow technology is an energetically and economically efficient option for the thermo-chemical conversion of biomass. Special attention is given to the pre-conditioning methods for biomass to enable the application in an entrained flow gasifier. Process chains are selected for the two gasifier types and subsequently transformed to simulation models. The simulation results show that the performance of both gasifier types is similar for the production of a pressurised product gas (2.5 MPa). The cold gas efficiency of the fluidised bed is 76–79% and about 0.5–2 percentage points higher than for the entrained flow reactor. The net efficiencies of both technologies are similar and between 64% and 71% depending on scale. The auxiliary power consumption of the entrained flow reactor is caused mainly by the air separation unit, the oxygen compression, and the fuel pulverisation, whereas the fluidised bed requires additional power mainly for gas compression. The costs for the product gas are determined as between €4.2 cent/kWh (500 MWth) and €7.4 cent/kWh (10 MWth) in the economic analysis of both technologies. The study indicates that the entrained flow

  13. Exploring Entrainment Patterns of Human Emotion in Social Media.

    Science.gov (United States)

    He, Saike; Zheng, Xiaolong; Zeng, Daniel; Luo, Chuan; Zhang, Zhu

    2016-01-01

    Emotion entrainment, which is generally defined as the synchronous convergence of human emotions, performs many important social functions. However, what the specific mechanisms of emotion entrainment are beyond in-person interactions, and how human emotions evolve under different entrainment patterns in large-scale social communities, are still unknown. In this paper, we aim to examine the massive emotion entrainment patterns and understand the underlying mechanisms in the context of social media. As modeling emotion dynamics on a large scale is often challenging, we elaborate a pragmatic framework to characterize and quantify the entrainment phenomenon. By applying this framework on the datasets from two large-scale social media platforms, we find that the emotions of online users entrain through social networks. We further uncover that online users often form their relations via dual entrainment, while maintain it through single entrainment. Remarkably, the emotions of online users are more convergent in nonreciprocal entrainment. Building on these findings, we develop an entrainment augmented model for emotion prediction. Experimental results suggest that entrainment patterns inform emotion proximity in dyads, and encoding their associations promotes emotion prediction. This work can further help us to understand the underlying dynamic process of large-scale online interactions and make more reasonable decisions regarding emergency situations, epidemic diseases, and political campaigns in cyberspace. PMID:26953692

  14. Exploring Entrainment Patterns of Human Emotion in Social Media

    Science.gov (United States)

    Luo, Chuan; Zhang, Zhu

    2016-01-01

    Emotion entrainment, which is generally defined as the synchronous convergence of human emotions, performs many important social functions. However, what the specific mechanisms of emotion entrainment are beyond in-person interactions, and how human emotions evolve under different entrainment patterns in large-scale social communities, are still unknown. In this paper, we aim to examine the massive emotion entrainment patterns and understand the underlying mechanisms in the context of social media. As modeling emotion dynamics on a large scale is often challenging, we elaborate a pragmatic framework to characterize and quantify the entrainment phenomenon. By applying this framework on the datasets from two large-scale social media platforms, we find that the emotions of online users entrain through social networks. We further uncover that online users often form their relations via dual entrainment, while maintain it through single entrainment. Remarkably, the emotions of online users are more convergent in nonreciprocal entrainment. Building on these findings, we develop an entrainment augmented model for emotion prediction. Experimental results suggest that entrainment patterns inform emotion proximity in dyads, and encoding their associations promotes emotion prediction. This work can further help us to understand the underlying dynamic process of large-scale online interactions and make more reasonable decisions regarding emergency situations, epidemic diseases, and political campaigns in cyberspace. PMID:26953692

  15. Exploring Entrainment Patterns of Human Emotion in Social Media.

    Directory of Open Access Journals (Sweden)

    Saike He

    Full Text Available Emotion entrainment, which is generally defined as the synchronous convergence of human emotions, performs many important social functions. However, what the specific mechanisms of emotion entrainment are beyond in-person interactions, and how human emotions evolve under different entrainment patterns in large-scale social communities, are still unknown. In this paper, we aim to examine the massive emotion entrainment patterns and understand the underlying mechanisms in the context of social media. As modeling emotion dynamics on a large scale is often challenging, we elaborate a pragmatic framework to characterize and quantify the entrainment phenomenon. By applying this framework on the datasets from two large-scale social media platforms, we find that the emotions of online users entrain through social networks. We further uncover that online users often form their relations via dual entrainment, while maintain it through single entrainment. Remarkably, the emotions of online users are more convergent in nonreciprocal entrainment. Building on these findings, we develop an entrainment augmented model for emotion prediction. Experimental results suggest that entrainment patterns inform emotion proximity in dyads, and encoding their associations promotes emotion prediction. This work can further help us to understand the underlying dynamic process of large-scale online interactions and make more reasonable decisions regarding emergency situations, epidemic diseases, and political campaigns in cyberspace.

  16. On the use of crystalline admixtures in cement based construction materials: from porosity reducers to promoters of self healing

    Science.gov (United States)

    Ferrara, Liberato; Krelani, Visar; Moretti, Fabio

    2016-08-01

    The project detailed in this paper aims at a thorough characterization of the effects of crystalline admixtures, currently employed as porosity reducing admixtures, on the self-healing capacity of the cementitious composites, i.e. their capacity to completely or partially re-seal cracks and, in case, also exhibit recovery of mechanical properties. The problem has been investigated with reference to both a normal strength concrete (NSC) and a high performance fibre reinforced cementitious composite (HPFRCC). In the latter case, the influence of flow-induced fibre alignment has also been considered in the experimental investigation. With reference to either 3-point (for NSC) or 4-point (for HPFRCC) bending tests performed up to controlled crack opening and up to failure, respectively before and after exposure/conditioning recovery of stiffness and stress bearing capacity has been evaluated to assess the self-healing capacity. In a durability-based design framework, self-healing indices to quantify the recovery of mechanical properties will also be defined. In NSC, crystalline admixtures are able to promote up to 60% of crack sealing even under exposure to open air. In the case of HPFRCCs, which would already feature autogenous healing capacity because of their peculiar mix compositions, the synergy between the dispersed fibre reinforcement and the action of the crystalline admixture has resulted in a likely ‘chemical pre-stressing’ of the same reinforcement, from which the recovery of mechanical performance of the material has greatly benefited, up to levels even higher than the performance of the virgin un-cracked material.

  17. Stability of entrainment on density interface of stratified fluids

    International Nuclear Information System (INIS)

    Entrainment behavior on a density interface of stratified fluids is very important for the piping design of various plants. In the previous study, it was found that the dimensionless entrainment velocity was inversely proportional to an overall Richardson number. This tendency was derived by the turbulent energy released from the energy-containing eddy was proportional to the energy consumption by the entrainment. In the present study, the tangential injection made the horizontal eddy above the density interface. The entrainment is done by the tornado formation by the horizontal eddy. The entrainment velocity by the horizontal eddy was compared with the model of the turbulent energy consumption by the entrainment. The effective entrainment behavior was obtained with the horizontal eddy. (author)

  18. Microphysical imprint of entrainment in warm cumulus

    OpenAIRE

    2013-01-01

    We analyse the cloud microphysical response to entrainment mixing in warm cumulus clouds observed from the CIRPAS Twin Otter during the GoMACCS field campaign near Houston, Texas, in summer 2006. Cloud drop size distributions and cloud liquid water contents from the Artium Flight phase-Doppler interferometer in conjunction with meteorological observations are used to investigate the degree to which inhomogeneous versus homogeneous mixing is preferred as a function of height above ...

  19. Microphysical imprint of entrainment in warm cumulus

    OpenAIRE

    Small, Jennifer D.; Chuang, Patrick Y.; Jonsson, Haflidi H.

    2013-01-01

    We analyse the cloud microphysical response to entrainment mixing in warm cumulus clouds observed from the CIRPAS Twin Otter during the GoMACCS field campaign near Houston, Texas, in summer 2006. Cloud drop size distributions and cloud liquid water contents from the Artium Flight phase-Doppler interferometer in conjunction with meteorological observations are used to investigate the degree to which inhomogeneous versus homogeneous mixing is preferred as a function of height above cloud base, ...

  20. Probing background ionization: Positive streamers with varying pulse repetition rate and with a radioactive admixture

    CERN Document Server

    Nijdam, S; van Veldhuizen, E M; Ebert, U

    2011-01-01

    Positive streamers need a source of free electrons ahead of them to propagate. A streamer can supply these electrons by itself through photo-ionization, or the electrons can be present due to external background ionization. Here we investigate the effects of background ionization on streamer propagation and morphology by changing the gas composition and the repetition rate of the voltage pulses, and by adding a small amount of radioactive Krypton 85. We find that the general morphology of a positive streamer discharge in high purity nitrogen depends on background ionization: at lower background ionization levels the streamers branch more and have a more feather-like appearance. This is observed both when varying the repetition rate and when adding Krypton 85, though side branches are longer with the radioactive admixture. But velocities and minimal diameters of streamers are virtually independent of the background ionization level. In air, the inception cloud breaks up into streamers at a smaller radius when ...

  1. THE EFFECT OF 800 0C ON BOND STRENGTH OF CONCRETE WITH MINERAL ADMIXTURE

    Directory of Open Access Journals (Sweden)

    Ahmet COŞKUN

    2007-03-01

    Full Text Available The effect of high temperature (800 0C on the bond strength between concrete and rebar was investigated. In addition to concrete mixture with only portland cement, concrete mixtures with 10% silica fume and 15 % fly ash replacing cement by weight was prepared. Maximum aggregate size is as 16 mm. The 150×150×150 mm cube specimens were prepared for compressive strength and the 100×200 mm cylinder specimens were prepared for bond strength. The specimens were cured in air for 270 days after curing in water 20±2 °C for 28 days. After being heated to temperatures of 800 ºC, compressive strength and bond strength of concrete were tested. The results showed that specimens with silica fume always gave the highest values followed by those as specimens with fly ash and specimens without mineral admixtures irrespective of type and age of concrete and test methods.

  2. Extensive Admixture and Selective Pressure Across the Sahel Belt

    Czech Academy of Sciences Publication Activity Database

    Triska, P.; Soares, P.; Patin, E.; Fernandes, V.; Černý, Viktor; Pereira, L.

    2015-01-01

    Roč. 7, č. 12 (2015), s. 3484-3495. ISSN 1759-6653 R&D Projects: GA ČR GA13-37998S Institutional support: RVO:67985912 Keywords : genome-wide diversity * admixture * selection * Sahel Subject RIV: AC - Archeology, Anthropology, Ethnology Impact factor: 4.229, year: 2014 http://gbe.oxfordjournals.org/content/7/12/3484.full.pdf+html

  3. Air

    Science.gov (United States)

    ... house) Industrial emissions (like smoke and chemicals from factories) Household cleaners (spray cleaners, air fresheners) Car emissions (like carbon monoxide) *All of these things make up “particle pollution.” They mostly come from cars, trucks, buses, and ...

  4. Mirror matter admixtures in K_L to mu^+ mu^-

    CERN Document Server

    Sánchez-Colón, G; Sanchez-Colon, Gabriel; Garcia, Augusto

    2006-01-01

    Our previous analysis on the contributions of mirror matter admixtures in ordinary hadrons to K_L to gamma gamma is extended to study the relevance of such contributions to the K_L to mu^+ mu^- rare decay. The mixing angle of the admixtures previously determined to describe the enhancement phenomenon in two body non-leptonic decays of strange hadrons is used, along with recent results for the description of the strong and electromagnetic interaction parts of the transition amplitudes. We find that these admixtures give a significant contribution with a small SU(3) breaking of only 2.8%, we also find a value of \\sim -17.9^{\\circ} for the eta-eta' mixing angle consistent with some of its determinations in the literature and a preferred negative value around -16 for the local counter-term contribution chi_1 + chi_2 consistent with the existence of a unique counter-term assuming lepton universality. We conclude that those mixings may be relevant in low energy physics and should not be ignored.

  5. Admixture mapping identifies introgressed genomic regions in North American canids.

    Science.gov (United States)

    vonHoldt, Bridgett M; Kays, Roland; Pollinger, John P; Wayne, Robert K

    2016-06-01

    Hybrid zones typically contain novel gene combinations that can be tested by natural selection in a unique genetic context. Parental haplotypes that increase fitness can introgress beyond the hybrid zone, into the range of parental species. We used the Affymetrix canine SNP genotyping array to identify genomic regions tagged by multiple ancestry informative markers that are more frequent in an admixed population than expected. We surveyed a hybrid zone formed in the last 100 years as coyotes expanded their range into eastern North America. Concomitant with expansion, coyotes hybridized with wolves and some populations became more wolflike, such that coyotes in the northeast have the largest body size of any coyote population. Using a set of 3102 ancestry informative markers, we identified 60 differentially introgressed regions in 44 canines across this admixture zone. These regions are characterized by an excess of exogenous ancestry and, in northeastern coyotes, are enriched for genes affecting body size and skeletal proportions. Further, introgressed wolf-derived alleles have penetrated into Southern US coyote populations. Because no wolves currently exist in this area, these alleles are unlikely to have originated from recent hybridization. Instead, they probably originated from intraspecific gene flow or ancient admixture. We show that grey wolf and coyote admixture has far-reaching effects and, in addition to phenotypically transforming admixed populations, allows for the differential movement of alleles from different parental species to be tested in new genomic backgrounds. PMID:27106273

  6. Recent admixture in an Indian population of African ancestry.

    Science.gov (United States)

    Narang, Ankita; Jha, Pankaj; Rawat, Vimal; Mukhopadhyay, Arijit; Mukhopadhayay, Arijit; Dash, Debasis; Basu, Analabha; Mukerji, Mitali

    2011-07-15

    Identification and study of genetic variation in recently admixed populations not only provides insight into historical population events but also is a powerful approach for mapping disease loci. We studied a population (OG-W-IP) that is of African-Indian origin and has resided in the western part of India for 500 years; members of this population are believed to be descendants of the Bantu-speaking population of Africa. We have carried out this study by using a set of 18,534 autosomal markers common between Indian, CEPH-HGDP, and HapMap populations. Principal-components analysis clearly revealed that the African-Indian population derives its ancestry from Bantu-speaking west-African as well as Indo-European-speaking north and northwest Indian population(s). STRUCTURE and ADMIXTURE analyses show that, overall, the OG-W-IPs derive 58.7% of their genomic ancestry from their African past and have very little inter-individual ancestry variation (8.4%). The extent of linkage disequilibrium also reveals that the admixture event has been recent. Functional annotation of genes encompassing the ancestry-informative markers that are closer in allele frequency to the Indian ancestral population revealed significant enrichment of biological processes, such as ion-channel activity, and cadherins. We briefly examine the implications of determining the genetic diversity of this population, which could provide opportunities for studies involving admixture mapping. PMID:21737057

  7. High-Performance Grouting Mortar Based on Mineral Admixtures

    Directory of Open Access Journals (Sweden)

    Cong Ma

    2015-01-01

    Full Text Available A study on high-performance grouting mortar is reported. The common mortar was modified by mineral admixtures such as gypsum, bauxite, and alunite. The effects of mineral admixtures on the fluidity, setting time, expansion, strength, and other properties of mortar were evaluated experimentally. The microstructure of the modified mortar was characterized by X-ray diffraction, scanning electron microscopy, and mercury intrusion porosimetry. Moreover, the expansive performance and strength of the grouting mortar were verified by anchor pullout test. The results show that the best conditions for gypsum-bauxite grouting mortar are as follows: a water-to-binder ratio of 0.3, a mineral admixture content of ~15%, and a molar ratio K of 2. The ultimate bearing capacity of the gypsum-bauxite grouting mortar anchor increased by 39.6% compared to the common mortar anchor. The gypsum-bauxite grouting mortar has good fluidity, quick-setting, microexpansion, early strength, and high strength performances.

  8. Measuring and using admixture to study the genetics of complex diseases

    Directory of Open Access Journals (Sweden)

    Halder Indrani

    2003-11-01

    Full Text Available Abstract Admixture is an important evolutionary force that can and should be used in efforts to apply genomic data and technology to the study of complex disease genetics. Admixture linkage disequilibrium (ALD is created by the process of admixture and, in recently admixed populations, extends for substantial distances (of the order of 10 to 20 cM. The amount of ALD generated depends on the level of admixture, ancestry information content of markers and the admixture dynamics of the population, and thus influences admixture mapping (AM. The authors discuss different models of admixture and how these can have an impact on the success of AM studies. Selection of markers is important, since markers informative for parental population ancestry are required and these are uncommon. Rarely does the process of admixture result in a population that is uniform for individual admixture levels, but instead there is substantial population stratification. This stratification can be understood as variation in individual admixtures and can be both a source of statistical power for ancestry-phenotype correlation studies as well as a confounder in causing false-positives in gene association studies. Methods to detect and control for stratification in case/control and AM studies are reviewed, along with recent studies showing individual ancestry-phenotype correlations. Using skin pigmentation as a model phenotype, implications of AM in complex disease gene mapping studies are discussed. Finally, the article discusses some limitations of this approach that should be considered when designing an effective AM study.

  9. Spectroscopic Investigations of Air Entrainment into an Argon Plasma Jet

    Czech Academy of Sciences Publication Activity Database

    Hlína, Jan; Něnička, Václav; Šlechta, Jiří; Krejčí, Luděk; Dolínek, Vladimír; Sopuch, Pavel

    Vol. 3. Orléans : GREMI, CNRS/University of Orléans, 2001 - (Bouchoule, A.; Pouvesle, J.), s. 1107-1110 [INTERNATIONAL SYMPOSIUM ON PLASMA CHEMISTRY /15./. Orléans (FR), 09.07.2001-13.07.2001] R&D Projects: GA AV ČR IAA1057001; GA ČR GA202/99/0389 Keywords : nitrogen molecular bands * dependence of nitrogen radiations on the argon flow rate Subject RIV: BL - Plasma and Gas Discharge Physics

  10. Entrained liquid fraction calculation in adiabatic disperse-annular flows at low rate in film

    Science.gov (United States)

    Yagov, V. V.; Minko, M. V.

    2016-04-01

    In this work, we continue our study [1] and extend further an approach to low reduced pressures. An approximate model of droplets entrainment from the laminar film surface and an equation for calculating entrainment intensity are proposed. To carry out direct verification of this equation using experimental data is extremely difficult because the integral effect—liquid flow rate in a film at a dynamic equilibrium between entrainment and deposition—is usually measured in the experiments. The balance between flows of droplets entrainment and deposition corresponds to the dynamic equilibrium because of turbulent diffusion. The transcendental equation, which was obtained on the basis of this balance, contains one unknown numerical factor and allows one to calculate the liquid rate. Comparing calculation results with the experimental data for the water-air and water-helium flows at low reduced pressures (less than 0.03) has shown their good agreement at the universal value of a numerical constant, if an additional dimensionless parameter, a fourth root of vaporliquid densities ratio, is introduced. The criterion that determines the boundary of using methods of this work and that of [1] in calculations and that reflects effect of pressure and state of film surface on distribution of the liquid in the annular flow is proposed; the numerical value of this criterion has been determined.

  11. Liquid entrainment at an upward oriented vertical branch line from a horizontal pipe

    Science.gov (United States)

    Welter, Kent Byron

    Under simulated accident conditions, tees in the primary coolant loop of a Pressurized Water Reactor (PWR) can deviate from their original design purpose and become separators that effectively remove core heat sink capacity. This method of primary coolant removal is a phenomenological subset of phase separation known as liquid entrainment, whereby liquid is forced from its original path by the inertia of the gas. A comprehensive literature review revealed common deficiencies in previous studies. The Westinghouse AP600 advanced reactor design was chosen to assess the validity of entrainment models. Following a systematic scaling analysis of the prototypic design a model separate effects test was proposed and constructed at Oregon State University. Just under 100 tests were run to fill the deficiencies found in the literature review. New data from the Air-water Test Loop for Advanced Thermal-hydraulic Studies (ATLATS) could not be predicted by published correlations. A new theoretical model for predicting liquid entrainment onset and steady state entrainment was developed. Comparison with all available data shows a marked improvement for predicting the mass flow rate out the vertical branch.

  12. Flow characteristics of sweepout and entrainment in the annular downcomer

    International Nuclear Information System (INIS)

    Sweepout from the water surface by gas (vapor or air) flow plays an important role in analyzing the mass and momentum transfer in the reactor downcomer of multidimensional geometry during a loss-of-coolant accident (LOCA) by decreasing the water level in the downcomer. The core water level will tend to decrease rapidly if a considerable amount of the entrained water stream and droplets bypasses through the break. The amount of entrained water is mostly determined by the interacting gas flow rate, the geometric condition, and the interfacial area between the gas and the water. The sweepout is observed to take place in three regions: the beginning of oscillation, the full wave and the wave peak (droplet separation). The beginning of oscillation normally occurs by the Helmholtz instability, which is defined in terms of the difference between the gas and the liquid velocities. The horizontal water surface is waved greatly before the gas flow reaches the critical point of droplet detachment. In the full-wave region, the droplets from the rough wave are swept into the gas flow and driven to the break. The water stream and droplets near the wave-peak region bypass through the break at extremely high velocities. In view of these observations we investigated the relation between the gas flow rate and the amount of bypass as a function of time. The test facility was constructed in a 1/10 linear scale-down model from the APR1400 (Advanced Power Reactor 1400MWe), which has four DVI (Direct Vessel Injection) lines, four cold legs, and two hot legs. The air was injected through the three intact cold legs and bypassed through the broken cold leg. The sweepout was visualized by using the acrylic test vessel. When the water level was located at the bottom of the break nozzle, the amount of bypass increased at the high Reynolds number of the gas. In the test the downcomer water level rapidly decreased for the initial one minute. Then, given the Reynolds number of the gas, the

  13. Air

    International Nuclear Information System (INIS)

    In recent years several regulations and standards for air quality and limits for air pollution were issued or are in preparation by the European Union, which have severe influence on the environmental monitoring and legislation in Austria. This chapter of the environmental control report of Austria gives an overview about the legal situation of air pollution control in the European Union and in specific the legal situation in Austria. It gives a comprehensive inventory of air pollution measurements for the whole area of Austria of total suspended particulates, ozone, volatile organic compounds, nitrogen oxides, sulfur dioxide, carbon monoxide, heavy metals, benzene, dioxin, polycyclic aromatic hydrocarbons and eutrophication. For each of these pollutants the measured emission values throughout Austria are given in tables and geographical charts, the environmental impact is discussed, statistical data and time series of the emission sources are given and legal regulations and measures for an effective environmental pollution control are discussed. In particular the impact of fossil-fuel power plants on the air pollution is analyzed. (a.n.)

  14. An experimental study of the liquid entrainment from swelled two-phase mixture surface in a reactor vessel

    International Nuclear Information System (INIS)

    An experimental study of liquid entrainment by rapid surface swellig of a two-phase mixture in a vessel has been performed. To investigate the effects of air flow and initial water level on the liquid entrainment, a series of experiments have been performed using air and water as working fluids. A total of 64 experimental liquid entrainment rate data have been obtained for various combinations of test parameters (i.e., six different initial water levels and varying air flow rates from 300 to 1,200 lpm) using two test vessels of the same height and different inner diameters (D=0.15 and 0.30m, respectively) for vertical bubbly and churn-turbulent flow conditions. An empirical correlation for the liquid entrainment rate, E, has been developed in terms of the superficial velocity of air, the initial water level, the density of gas, the surface tension, and the gravity. This correlation shows a good agreement with the present experimental data within 30% over a wide range of flow parameters

  15. Entrainment and mixing in thrust augmenting ejectors

    Science.gov (United States)

    Bernal, L.; Sarohia, V.

    1983-01-01

    An experimental investigation of two-dimensional thrust augmenting ejector flows has been conducted. Measurements of the shroud surface pressure distribution, mean velocity, turbulent intensities and Reynolds stresses were made in two shroud geometries at various primary nozzle pressure ratios. The effects of shroud geometry and primary nozzle pressure ratio on the shroud surface pressure distribution, mean flow field and turbulent field were determined. From these measurements the evolution of mixing within the shroud of the primary flow and entrained fluid was obtained. The relationship between the mean flow field, the turbulent field and the shroud surface pressure distribution is discussed.

  16. Assessment of impact due to entrainment of ichthyoplankton

    International Nuclear Information System (INIS)

    Three approaches to the assessment of impact associated with the entrainment of ichthyoplankton into power stations are discussed. The first is the estimation of the probability of mortality for those organisms entrained. The second is the assessment to the fish populations which have the egg and larvae life stages entrained. The third approach is the assessment of impact to the community or ecosystem. Some models are presented as examples for each of the three approaches. (U.S.)

  17. Argon entrainment into liquid sodium in fast breeder reactor

    International Nuclear Information System (INIS)

    Highlights: ► In the present work, different types of entrainment mechanisms have been studied. ► Onset of entrainment could be characterized with turbulent intensities. ► For vortex type entrainment, a correlation has been proposed. - Abstract: Gas entrainment in pool type sodium cooled fast breeder reactors has been a subject of great interest for a quite long time now. The issue of entrainment of argon cover gas in LMFBR's is being addressed by fundamental studies. Present work focuses on characterization of onset of shear type entrainment and liquid fall type entrainment based on mean velocity and turbulent kinetic energy at liquid surface. Study also includes characterization of onset of vortex type entrainment based on mean velocities (time averaged) in the outlet pipe. Experiments were carried out to characterize shear type entrainment in stirred tank with different impeller geometries with air–water and xylene–water systems. Onset of liquid fall type entrainment was studied with cylindrical tank with a nozzle whose input angle varied. Mean and r.m.s. velocity profiles near the liquid surface were measured with the help of ultrasonic velocity profiler (UVP). The results are compared with other literature. It is observed that the onset of entrainment can be characterized by the turbulent kinetic energy near the free liquid surface. Re-submergence angle was measured and r.m.s. velocities found to be in the same range as in case of shear type of entrainment. Cylindrical tank with tangential inlet and bottom outlet was used to study onset of vortex formation. Effect of different parameters like outlet diameter, tank diameter and liquid height in the tank on critical velocity was studied and correlation has been proposed.

  18. Practical handling of AIO admixtures – Guidelines on Parenteral Nutrition, Chapter 10

    OpenAIRE

    Stanga, Z; Franken, C.; Mühlebach, S; Working group for developing the guidelines for parenteral nutrition of The German Association for Nutritional Medicine

    2009-01-01

    All-in-one admixtures (AIO-admixtures) provide safe, effective and low-risk PN (parenteral nutrition) for practically all indications and applications. Water, energy (carbohydrates and lipids), amino acids, vitamins and trace elements are infused together with PN either as industrially-manufactured AIO admixtures provided as two- or three-chamber bags (shelf life usually more than 12 months) completed with electrolytes and micronutrients where appropriate or as individually compounded ready-t...

  19. Practical handling of AIO admixtures - Guidelines on Parenteral Nutrition, Chapter 10

    OpenAIRE

    Mühlebach, S; Franken, C.; Stanga, Z; Working group for developing the guidelines for parenteral nutrition of The German Association for Nutritional Medicine

    2009-01-01

    All-in-one admixtures (AIO-admixtures) provide safe, effective and low-risk PN (parenteral nutrition) for practically all indications and applications. Water, energy (carbohydrates and lipids), amino acids, vitamins and trace elements are infused together with PN either as industrially-manufactured AIO admixtures provided as two- or three-chamber bags (shelf life usually more than 12 months) completed with electrolytes and micronutrients where appropriate or as individually compounded ready-t...

  20. Polycarboxylate superplasticiser admixtures: effect on hydration, microstructure and rheological behaviour in cement pastes

    OpenAIRE

    Puertas, F.; Santos, H.; Palacios, M.; Martínez-Ramírez, Sagrario

    2005-01-01

    A study was conducted on the effect of a polycarboxylate (PC) admixture on the mechanical, mineralogical, microstructural and rheological behaviour of Portland cement pastes. It was observed that the presence of PC admixture retards the initial cement hydration reactions, although this effect may be offset by possible increased diffusion in later stages. Additionally, the PC admixtures produce a few alterations in the structure and composition of the formed C–S–H gel. The addition of 1% PC...

  1. Dating the age of admixture via wavelet transform analysis of genome-wide data.

    Science.gov (United States)

    Pugach, Irina; Matveyev, Rostislav; Wollstein, Andreas; Kayser, Manfred; Stoneking, Mark

    2011-01-01

    We describe a PCA-based genome scan approach to analyze genome-wide admixture structure, and introduce wavelet transform analysis as a method for estimating the time of admixture. We test the wavelet transform method with simulations and apply it to genome-wide SNP data from eight admixed human populations. The wavelet transform method offers better resolution than existing methods for dating admixture, and can be applied to either SNP or sequence data from humans or other species. PMID:21352535

  2. Dating the age of admixture via wavelet transform analysis of genome-wide data

    OpenAIRE

    Pugach, Irina; Matveyev, Rostislav; Wollstein, Andreas; Kayser, Manfred; Stoneking, Mark

    2011-01-01

    textabstractWe describe a PCA-based genome scan approach to analyze genome-wide admixture structure, and introduce wavelet transform analysis as a method for estimating the time of admixture. We test the wavelet transform method with simulations and apply it to genome-wide SNP data from eight admixed human populations. The wavelet transform method offers better resolution than existing methods for dating admixture, and can be applied to either SNP or sequence data from humans or other species.

  3. "Air embolism during fontan operation"

    Directory of Open Access Journals (Sweden)

    Madan Mohan Maddali

    2014-01-01

    Full Text Available In patients with a right to left intracardiac shunt, air embolism results in an obligatory systemic embolization. Nonembolization of entrained air is described in a child with a single ventricle physiology who had earlier undergone bidirectional Glenn shunt construction and Damus-Kaye-Stansel anastomosis. The air entrainment was detected by intra-operative transesophageal echocardiography. The combined effect of a "diving bell" phenomenon and mild aortic valve regurgitation are suggested as the reasons for the confinement of air into the ventricle preventing catastrophic systemic embolization.

  4. Entrainment, Drizzle, and the Indirect Effect in Stratiform Clouds

    Science.gov (United States)

    Ackerman, Andrew

    2005-01-01

    Activation of some fraction of increased concentrations of sub-micron soluble aerosol particles lead to enhanced cloud droplet concentrations and hence smaller droplets, increasing their total cross sectional area and thus reflecting solar radiation more efficiently (the Twomey, or first indirect, effect). However, because of competition during condensational growth, droplet distributions tend to broaden as numbers increase, reducing the sensitivity of cloud albedo to droplet concentration on the order of 10%. Also, smaller droplets less effectively produce drizzle through collisions and coalescence, and it is widely expected (and found in large-scale models) that decreased precipitation leads to clouds with more cloud water on average (the so-called cloud lifetime, or second indirect, effect). Much of the uncertainty regarding the overall indirect aerosol effect stems from inadequate understanding of such changes in cloud water. Detailed simulations based on FIRE-I, ASTEX, and DYCOMS-II conditions show that suppression of precipitation from increased droplet concentrations leads to increased cloud water only when sufficient precipitation reaches the surface, a condition favored when the overlying air is-humid or droplet concentrations are very low. Otherwise, aerosol induced suppression of precipitation enhances entrainment of overlying dry air, thereby reducing cloud water and diminishing the indirect climate forcing.

  5. Practical handling of AIO admixtures – Guidelines on Parenteral Nutrition, Chapter 10

    Directory of Open Access Journals (Sweden)

    Stanga, Z.

    2009-11-01

    Full Text Available All-in-one admixtures (AIO-admixtures provide safe, effective and low-risk PN (parenteral nutrition for practically all indications and applications. Water, energy (carbohydrates and lipids, amino acids, vitamins and trace elements are infused together with PN either as industrially-manufactured AIO admixtures provided as two- or three-chamber bags (shelf life usually more than 12 months completed with electrolytes and micronutrients where appropriate or as individually compounded ready-to-use AIO admixtures (compounding, usually prepared by a pharmacy on either a daily or weekly basis and stored at 2–8°C. Physico-chemical and microbial stability of an AIO admixture is essential for the safety and effectiveness of patient-specific PN, and its assurance requires specialist pharmaceutical knowledge. The stability should be documented for an application period of 24 (–48 hours. It is advisable to offer a limited selection of different PN regimes in each hospital. For reasons of drug and medication safety, PN admixtures prepared for individual patients must be correctly labelled and specifications for storage conditions must also be followed during transport. Monitoring is required where applicable. Micronutrients are usually administered separately to AIO admixtures. In case compatibility and stability have been well documented trace elements and/or combination preparations including water-soluble or water-soluble/fat soluble vitamin supplements can be added to PN admixtures under strict aseptic conditions. AIO admixtures are usually not used as vehicles for drugs (incompatibilities.

  6. Effect of Anti-freezing Admixtures on Alkali-silica Reaction in Mortars

    Institute of Scientific and Technical Information of China (English)

    LIU Junzhe; LI Yushun; LV Lihua

    2005-01-01

    The influence of anti-freezing admixture on the alkali aggregate reaction in mortar was analyzed with accelerated methods. It is confirmed that the addition of sodium salt ingredients of anti-freezing admixture accelerates the alkali silica reaction to some extent, whereas calcium salt ingredient of anti-freezing admixture reduces the expansion of alkali silica reaction caused by high alkali cement. It is found that the addition of the fly ash considerably suppresses the expansion of alkali silica reaction induced by the anti-freezing admixtures.

  7. Effect of liquid entrainment on turbulent mixing rates between subchannels in gas-liquid annular two-phase flows

    International Nuclear Information System (INIS)

    Turbulent mixing rates of gas and liquid phases between adjacent subchannels have been measured for various air-water two-phase annular flows in a multiple channel consisting of two identical circular subchannels. In order to study effect of liquid entrainment in the gas core on the turbulent mixing rates, experiments were conducted for two types of liquid injection method, i.e., a small bore nozzle placed in the subchannel center and a porous wall. The result showed that the effect of liquid entrainment on the turbulent mixing rates of both phases is negligibly small. (author)

  8. Stochastic entrainment of a stochastic oscillator.

    Science.gov (United States)

    Wang, Guanyu; Peskin, Charles S

    2015-11-01

    In this work, we consider a stochastic oscillator described by a discrete-state continuous-time Markov chain, in which the states are arranged in a circle, and there is a constant probability per unit time of jumping from one state to the next in a specified direction around the circle. At each of a sequence of equally spaced times, the oscillator has a specified probability of being reset to a particular state. The focus of this work is the entrainment of the oscillator by this periodic but stochastic stimulus. We consider a distinguished limit, in which (i) the number of states of the oscillator approaches infinity, as does the probability per unit time of jumping from one state to the next, so that the natural mean period of the oscillator remains constant, (ii) the resetting probability approaches zero, and (iii) the period of the resetting signal approaches a multiple, by a ratio of small integers, of the natural mean period of the oscillator. In this distinguished limit, we use analytic and numerical methods to study the extent to which entrainment occurs. PMID:26651734

  9. Observing of entrainment using small UAS

    Science.gov (United States)

    Martin, S.; Bange, J.; Beyrich, F.

    2012-04-01

    Entrainment processes between the atmospheric boundary layer and the free atmosphere are important concerning vertical exchange of momentum, energy, water vapor, trace gases and aerosol. The transition zone between the convectively mixed boundary layer and the stably stratified free atmosphere is called the entrainment zone (EZ). The EZ restrains the domain of turbulence by a temperature inversion and acts as a lid to pollutants. Measurement flights of the mini meteorological aerial vehicle (M2AV) of the Technische Universität Braunschweig were performed in spring 2011 to determine the capability of the unmanned aerial system (UAS) to measure the structure of the EZ. The campaign took place at the Meteorological Observatory Lindenberg / Richard-Aßmann-Observatory of the German Meteorological Service, which is located close to Berlin. Besides the M2AV flights, standard observations were performed by a 12 m and 99 m tower, a sodar, ceilometer and radiosondes. A tethered balloon with measurement units at six different levels was operated especially for this campaign. The measurements of these systems were used to determine the inversion layer and to capture its diurnal cycle. The talk will be focused on vertical profiles of the M2AV up to the free atmosphere, detailed analysis of spatial series of w'θ' at different altitudes and on vertical profiles of normalized variances of the vertical wind component and the potential temperature.

  10. The influence of shrinkage reducing admixtures on plastic shrinkage

    Directory of Open Access Journals (Sweden)

    Mora, J.

    2003-12-01

    Full Text Available Shrinkage reducing admixtures (SRAs are viable alternatives for reducing plastic shrinkage cracking in concrete. The objective of the present paper is to study early age plastic shrinkage in restrained concrete elements, where three different SRAs have been used. The influence of the admixture is analyzed through the following measurements: capillary pressure, evaporation, temperature evolution, crack evolution and settlement. The tests for studying the cracking and deformation were made on two different configurations (i.e., restrained prisms with reduced cross-section and restrained panel, in a wind tunnel, with controlled wind temperature and velocity. The conclusions obtained indicate the viability of the use of this type of admixture and the usefulness of the test methods.

    Los aditivos reductores de retracción (SRAs se plantean, hoy en día, como una alternativa viable para reducir la fisuración por retracción plástica. El objetivo del presente artículo es conocer mejor y predecir el comportamiento a primeras edades de la retracción plástica en elementos estructurales coaccionados, a los que se les ha añadido diversos aditivos reductores de retracción (tres tipos diferentes. Esta influencia se analiza a través de las siguientes propiedades: presión capilar, evaporación, evolución de temperaturas, evolución de fisuración, y deformaciones verticales de asentamiento. Los ensayos para estudiar la fisuración y las deformaciones se han realizado sobre diferentes configuraciones (prisma restringido con estrangulamiento y panel restringido, en un túnel de viento, con temperaturas y velocidades de viento controladas. Las conclusiones obtenidas señalan la viabilidad del empleo de este tipo de aditivos y la bondad de los métodos experimentales utilizados.

  11. A genomewide admixture mapping panel for Hispanic/Latino populations.

    Science.gov (United States)

    Mao, Xianyun; Bigham, Abigail W; Mei, Rui; Gutierrez, Gerardo; Weiss, Ken M; Brutsaert, Tom D; Leon-Velarde, Fabiola; Moore, Lorna G; Vargas, Enrique; McKeigue, Paul M; Shriver, Mark D; Parra, Esteban J

    2007-06-01

    Admixture mapping (AM) is a promising method for the identification of genetic risk factors for complex traits and diseases showing prevalence differences among populations. Efficient application of this method requires the use of a genomewide panel of ancestry-informative markers (AIMs) to infer the population of origin of chromosomal regions in admixed individuals. Genomewide AM panels with markers showing high frequency differences between West African and European populations are already available for disease-gene discovery in African Americans. However, no such a map is yet available for Hispanic/Latino populations, which are the result of two-way admixture between Native American and European populations or of three-way admixture of Native American, European, and West African populations. Here, we report a genomewide AM panel with 2,120 AIMs showing high frequency differences between Native American and European populations. The average intermarker genetic distance is ~1.7 cM. The panel was identified by genotyping, with the Affymetrix GeneChip Human Mapping 500K array, a population sample with European ancestry, a Mesoamerican sample comprising Maya and Nahua from Mexico, and a South American sample comprising Aymara/Quechua from Bolivia and Quechua from Peru. The main criteria for marker selection were both high information content for Native American/European ancestry (measured as the standardized variance of the allele frequencies, also known as "f value") and small frequency differences between the Mesoamerican and South American samples. This genomewide AM panel will make it possible to apply AM approaches in many admixed populations throughout the Americas. PMID:17503334

  12. Mirror matter admixtures in K_S to gamma gamma

    CERN Document Server

    Sánchez-Colón, G; Sanchez-Colon, Gabriel; Garcia, Augusto

    2006-01-01

    The latest measurement of the K_S to gamma gamma branching ratio clearly shows an enhancement over the current theoretical prediction. As in other K and B meson decays, this invites to consider the possibility of the contribution of new physics. We study a particular form of the latter, which may be referred to as manifest mirror symmetry. The experimental data are described using previously determined values for the mixing angles of the admixtures of mirror matter in ordinary hadrons and by assuming that for pi^0, eta, eta', the mirror decay amplitudes have the same magnitudes as their ordinary counterparts.

  13. Symmetry limit properties of decay amplitudes with mirror matter admixtures

    CERN Document Server

    Sánchez-Colón, G; Sanchez-Colon, Gabriel; Garcia, Augusto

    2006-01-01

    We extend our previous analysis on the symmetry limit properties of non-leptonic and weak radiative decay amplitudes of hyperons in a scheme of mirror matter admixtures in physical hadrons to include the two-body non-leptonic decays of $\\Omega^-$ and the two photon and two pion decays of kaons. We show that the so-called parity-conserving amplitudes predicted for all the decays vanish in the strong flavor SU(3) symmetry limit. We also establish the specific conditions under which the corresponding so-called parity-violating amplitudes vanish in the same limit.

  14. Whistler Solitons in Plasma with Anisotropic Hot Electron Admixture

    Science.gov (United States)

    Khazanov, G. V.; Krivorutsky, E. N.; Gallagher, D. L.

    1999-01-01

    The longitudinal and transverse modulation instability of whistler waves in plasma, with a small admixture of hot anisotropic electrons, is discussed. If the hot particles temperature anisotropy is positive, it is found that, in such plasma, longitudinal perturbations can lead to soliton formation for frequencies forbidden in cold plasma. The soliton is enriched by hot particles. The frequency region unstable to transverse modulation in cold plasma in the presence of hot electrons is divided by stable domains. For both cases the role of hot electrons is more significant for whistlers with smaller frequencies.

  15. Effect of polycarboxylate admixture structure on cement paste rheology

    OpenAIRE

    Aranda, M. A. G.; De la Torre, A.G.; Puertas, F.; Palacios, M.; Alonso, M M

    2007-01-01

    The purpose of the present study was to analyze the effect of the structural differences in four polycarboxylate and polyether admixtures on the rheological properties of cement pastes with different chemical and mineralogical compositions and different active additions (CEM I 42.5 R, CEM I 52.5 R, CEM I 52.5 N/SR, CEM II/AV 42.5R, CEM II/B-L 32.5 R, CEM III/B 32.5R, BL I 52.5R and CAC – European standard EN 197-1:2000). The results of the minislump test concurred with the variations ob...

  16. Influence of chloride admixtures on cement matrix durability

    International Nuclear Information System (INIS)

    The influence of various inorganic salts, as chloride admixtures to Portland cement, on the mechanical properties and the durability of the matrix has been studied. The salts used in this study are chromium, nickel and cadmium chlorides. Improved compressive strength values are obtained which have been correlated to the stable metal hydroxide formation in high pH environment. Under static water conditions at 500C, hydrolyzed chloride ions exhibit adverse effects on the matrix durability through rapid release of calcium as calcium chloride in the initial period of leaching. On the contrary, enhanced matrix durability is obtained on long term leaching in the case of cement containing chromium chloride

  17. Dilution of aircraft exhaust and entrainment rates for trajectory box models

    Energy Technology Data Exchange (ETDEWEB)

    Gerz, T. [Deutsche Forschungsanstalt fuer Luft- und Raumfahrt e.V. (DLR), Oberpfaffenhofen (Germany). Inst. fuer Physik der Atmosphaere; Kaercher, B. [Muenchen Univ. (Germany). Lehrstuhl fuer Bioklimatologie und Immissionsforschung

    1997-12-31

    In order to match in-situ measured concentrations of NO and NO{sub 2} in the wake, dilution factors or entrainment rates have to be used which take into account that the largest fraction of the exhaust is captured by the wing tip vortices. This fraction defines the primary wake. Baroclinicity and turbulence detrains parts of it later into the secondary wake. Both wake regimes undergo different chemical and microphysical histories. The rates {omega} are determined at which ambient air becomes entrained into the primary and the secondary portion of the exhaust plume. Numerical simulations of the highly resolved wake is used of cruising aircraft under typical atmosphere conditions with and without ambient turbulence. The simulations are oriented on a case where exhaust and dynamical data behind an eastbound travelling B-747 aircraft have been collected in-situ over the North-Atlantic east of Ireland. (author) 7 refs.

  18. Rhythm as a Coordinating Device: Entrainment with Disordered Speech

    Science.gov (United States)

    Borrie, Stephanie A.; Liss, Julie M.

    2014-01-01

    Purpose: The rhythmic entrainment (coordination) of behavior during human interaction is a powerful phenomenon, considered essential for successful communication, supporting social and emotional connection, and facilitating sense-making and information exchange. Disruption in entrainment likely occurs in conversations involving those with speech…

  19. No Time To Kill: Entrainment and Accelerating Courseware Development.

    Science.gov (United States)

    Millington, Paula Crnkovich

    This paper examines the concept of time in multimedia, World Wide Web-based courseware development. The biological concept of entrainment (the alignment of rhythms within and between systems) to accelerate courseware development is explored. The discussion begins with the foundational concepts of entrainment from biological systems and social…

  20. Volcanic jets, plumes, and collapsing fountains: evidence from large-scale experiments, with particular emphasis on the entrainment rate

    Science.gov (United States)

    Dellino, P.; Dioguardi, F.; Mele, D.; D'Addabbo, M.; Zimanowski, B.; Büttner, R.; Doronzo, D. M.; Sonder, I.; Sulpizio, R.; Dürig, T.; La Volpe, L.

    2014-06-01

    The source conditions of volcanic plumes and collapsing fountains are investigated by means of large-scale experiments. In the experiments, gas-particle jets issuing from a cylindrical conduit are forced into the atmosphere at different mass flow rates. Dense jets (high particle volumetric concentration, e.g., C 0 > 0.01) generate collapsing fountains, whose height scales with the squared exit velocity. This is consistent with Bernoulli's equation, which is a good approximation if air entrainment is negligible. In this case, kinetic energy is transformed into potential energy without any significant loss by friction with the atmosphere. The dense collapsing fountain, on hitting the ground, generates an intense shear flow similar to a pyroclastic density current. Dilute hot jets (low particle volumetric concentration, e.g., C 0 air entrainment results in this case, leading to the formation of a buoyant column (plume) from which particles settle similarly to pyroclastic fallout. The direct measurement of entrainment coefficient in the experiments suggests that dense collapsing fountains form only when air entrainment is not significant. This is a consequence of the large density difference between the jet and the atmosphere. Cold dilute experiments result in an entrainment coefficient of about 0.06, which is typical of pure jets of fluid dynamics. Hot dilute experiments result in an entrainment coefficient of about 0.11, which is typical of thermally buoyant plumes. The entrainment coefficients obtained by experiments were used as input data in numerical simulations of fountains and plumes. A numerical model was used to solve the classic top-hat system of governing equations, which averages the field variables (e.g., column velocity and density) across the column. The maximum heights calculated with the model agree well with those observed experimentally, showing that our entrainment coefficients are compatible with a top-hat model. Dimensional analysis of the

  1. Incorporation of Mineral Admixtures in Sustainable High Performance Concrete

    Directory of Open Access Journals (Sweden)

    Nima Farzadnia

    2011-07-01

    Full Text Available Concrete is a widely used construction material around the world, and its properties have been undergoing changes through technological advancement. Numerous types of concrete have been developed to enhance the different properties of concrete. So far, this development can be divided into four stages. The earliest is the traditional normal strength concrete which is composed of only four constituent materials, which are cement, water, fine and coarse aggregates. With a fast population growth and a higher demand for housing and infrastructure, accompanied by recent developments in civil engineering, such as high-rise buildings and long-span bridges, higher compressive strength concrete was needed. At the beginning, reducing the water-cement ratio was the easiest way to achieve the high compressive strength. Thereafter, the fifth ingredient, a water reducing agent or super plasticizer, was indispensable. However, sometimes the compressive strength was not as important as some other properties, such as low permeability, durability and workability. Thus, high performance concrete was proposed and widely studied at the end of the last century. Currently, high-performance concrete is used in massive volumes due to its technical and economic advantages. Such materials are characterized by improved mechanical and durability properties resulting from the use of chemical and mineral admixtures as well as specialized production processes. This paper reviews the incorporation of mineral admixtures in binary, ternary and quaternary blended mortars in concrete.

  2. Physicochemical compatibility of nebulizable drug admixtures containing colistimethate and tobramycin.

    Science.gov (United States)

    Wollstadt, A; Krämer, I; Kamin, W

    2013-09-01

    Inhalation therapy with nebulizable antibiotic drugs is a mainstay in treating Pseudomonas aeruginosa infections in cystic fibrosis patients. The combination of tobramycin and colistin was found to be superior to monotherapy in killing P. aeruginosa in biofilms. The simultaneous inhalation of tobramycin and colistin might be an option to increase the compliance of patients. The objective of this in-vitro study was to determine whether admixtures of inhalation solutions containing colistin methanesulfonate (CMS) and tobramycin are physicochemically compatible. Physical compatibility was determined by measuring pH and osmolality. Chemical compatibility was determined by testing the antibiotic activity of the mixtures by the pharmacopoeial microbiological assay and comparing the results to those of standard solutions. Samples were analyzed immediately after mixing and after 24 h. Values of pH and osmolality remained unchanged and in physiologically acceptable ranges. Neither for colistin methanesulfonate (CMS) nor for tobramycin losses of antibiotic potency were registered at any time. Admixtures of nebulizer solutions containing CMS and tobramycin were shown to be physicochemically compatible. Further investigations are needed to determine whether drug delivery is affected by mixing the nebulizer solutions to ensure that simultaneous inhalation is recommendable. PMID:24147342

  3. Synchronization and entrainment of coupled circadian oscillators

    CERN Document Server

    Komin, Niko; Hernandez-Garcia, Emilio; Toral, Raul

    2010-01-01

    Circadian rhythms in mammals are controlled by the neurons located in the suprachiasmatic nucleus of the hypothalamus. In physiological conditions, the system of neurons is very efficiently entrained by the 24-hour light-dark cycle. Most of the studies carried out so far emphasize the crucial role of the periodicity imposed by the light dark cycle in neuronal synchronization. Nevertheless, heterogeneity as a natural and permanent ingredient of these cellular interactions is seemingly to play a major role in these biochemical processes. In this paper we use a model that considers the neurons of the suprachiasmatic nucleus as chemically-coupled modified Goodwin oscillators, and introduce non-negligible heterogeneity in the periods of all neurons in the form of quenched noise. The system response to the light-dark cycle periodicity is studied as a function of the interneuronal coupling strength, external forcing amplitude and neuronal heterogeneity. Our results indicate that the right amount of heterogeneity hel...

  4. Scalar entrainment in the mixing layer

    Science.gov (United States)

    Sandham, N. D.; Mungal, M. G.; Broadwell, J. E.; Reynolds, W. C.

    1988-01-01

    New definitions of entrainment and mixing based on the passive scalar field in the plane mixing layer are proposed. The definitions distinguish clearly between three fluid states: (1) unmixed fluid, (2) fluid engulfed in the mixing layer, trapped between two scalar contours, and (3) mixed fluid. The difference betwen (2) and (3) is the amount of fluid which has been engulfed during the pairing process, but has not yet mixed. Trends are identified from direct numerical simulations and extensions to high Reynolds number mixing layers are made in terms of the Broadwell-Breidenthal mixing model. In the limit of high Peclet number (Pe = ReSc) it is speculated that engulfed fluid rises in steps associated with pairings, introducing unmixed fluid into the large scale structures, where it is eventually mixed at the Kolmogorov scale. From this viewpoint, pairing is a prerequisite for mixing in the turbulent plane mixing layer.

  5. Projected entrainment of fish resulting from aggregate dredging

    International Nuclear Information System (INIS)

    Previous research to assess impacts from aggregate dredging has focussed on infaunal species with few studies made of fish entrainment. Entrainment evidence from hydraulic dredging studies is reviewed to develop a sensitivity index for benthic fish. Environmental monitoring attendant with the granting of new licences in the Eastern Channel Region (ECR) in 2006 offers a unique opportunity to assess the effects of dredging upon fish. Projected theoretical fish entrainment rates are calculated based upon: abundance data from 4m beam trawl sampling of fish species over the period 2005–2008; sensitivity data; and dredging activity and footprint derived from Electronic monitoring System (EMS) data. Results have been compared with actual entrainment rates and also against summary results from independent analysis of the changes in fish population over the period 2005–2008 (). The case is made for entrainment surveys to form part of impact monitoring for marine aggregate dredging.

  6. Mitigation of gas entrainment in sodium cooled fast reactors

    International Nuclear Information System (INIS)

    Argon cover gas may entrain into sodium in the hot pool and in the surge tank of liquid Sodium cooled Fast Reactor (SFR) due to various mechanisms. The entrained cover gas may hinder the normal reactor operation in many ways such as reduction in heat transfer in the heat exchanger, causing neutronic perturbation inside the core etc. The recirculating gas bubbles also enhance chances of cavitation in the pumps. Therefore, it is required to mitigate gas entrainment in reactor. High free surface velocity and turbulence level are the causes of gas entrainment from free surface. Hence, gas entrainment can be avoided by reducing these factors at free surface. This is achieved by employing gas entrainment mitigation devices which essentially alters the flow pattern and reduces velocity and turbulence level at the free surface. A combined experimental and computational approach is proposed to develop such devices. The computational model which is used for parametric studies is first validated against experiments carried out in scale down water model of reactor primary circuit and surge tank. The effect of different gas entrainment mitigating devices for reduction in free surface velocity and turbulence level has been analyzed using this validated CFD model. Based on the CFD analyses, the final geometry of the gas entrainment mitigating devices has been selected and optimized. Finally the selected devices have been tested to confirm its performance for mitigation of gas entrainment in large scale models of reactor primary circuit and surge tank. This paper presents the studies carried out towards development of suitable gas entrainment mitigation devices for hot pool and surge tank of SFR. (author)

  7. Fly Ash Admixture and its Influence on Alitic Type Cement Concrete Permeability

    OpenAIRE

    Rujanu, Mircea; Rujanu, Bogdan

    2012-01-01

    Experimental and theoretical studies pointed that adding fly ash in concrete composition, could favour its impermeability characteristic improvement. It is known, also, that fly ash admixture achieves cement dosage reduction, so that concrete will be cheaper, and in this conditions it is important to analyse fly ash admixture influence on impermeability degree, too.

  8. Genome-wide Ancestry Patterns in Rapanui Suggest Pre-European Admixture with Native Americans

    DEFF Research Database (Denmark)

    Moreno-Mayar, J. Víctor; Rasmussen, Simon; Seguin-Orlando, Andaine;

    2014-01-01

    . We found a mostly Polynesian ancestry among Rapanui and detected genome-wide patterns consistent with Native American and European admixture. By considering the distribution of local ancestry tracts of eight unrelated Rapanui, we found statistical support for Native American admixture dating to AD...

  9. Dating the age of admixture via wavelet transform analysis of genome-wide data

    NARCIS (Netherlands)

    I. Pugach (Irina); R. Matveyev (Rostislav); A. Wollstein (Andreas); M.H. Kayser (Manfred); M. Stoneking (Mark)

    2011-01-01

    textabstractWe describe a PCA-based genome scan approach to analyze genome-wide admixture structure, and introduce wavelet transform analysis as a method for estimating the time of admixture. We test the wavelet transform method with simulations and apply it to genome-wide SNP data from eight admixe

  10. The application study of polycarboxylates water-reducing admixture in passenger dedicated line engineering%The application study of polycarboxylates water-reducing admixture in passenger dedicated line engineering

    Institute of Scientific and Technical Information of China (English)

    Huang Zhijiu

    2012-01-01

    Polycarboxylate water-reducing admixture possesses the capability which could meet with the comprehensive performance of high performance concrete used in passenger dedicated line engineering. The problems of polycarboxylates water-reducing admixtures existed in the engineering application of were analyzed. At present the key for polycarboxylates application was to settle the compatibility between the water-reducing admixture and the cement and to keep the quality retention of this admixture.

  11. Admixture analysis and stocking impact assessment in brown trout ( Salmo trutta ), estimated with incomplete baseline data

    DEFF Research Database (Denmark)

    Hansen, Michael Møller; Eg Nielsen, Einar; Bekkevold, Dorte;

    2001-01-01

    Studies of genetic interactions between wild and domesticated fish are often hampered by unavailability of samples from wild populations prior to population admixture. We assessed the utility of a new Bayesian method, which can estimate individual admixture coefficients even with data missing from...... the populations contributing to admixture. We applied the method to analyse the genetic contribution of domesticated brown trout (Salmo trutta) in samples of anadromous trout from two stocked populations with no genetic data available before stocking. Further, we estimated population level admixture proportions...... by the mean of individual admixture coefficients. This method proved more informative than a multidimensional scaling analysis of individual-based genetic distances and assignment tests. The results showed almost complete absence of stocked, domesticated trout in samples of trout from the rivers. Consequently...

  12. EFFECTS OF CHEMICAL ADMIXTURES ON SPECIALITIES OF HARDENED CONCRETE USED IN READY CONCRETE PRODUCTION IN ESKİŞEHİR

    OpenAIRE

    TOPÇU, İlker Bekir; IŞIKDAĞ, Burak; Özgür TATAR

    2006-01-01

    In this study polls were taken from different ready mixed concrete firms in Eskişehir. Chemical admixtures used in concrete production were investigated according to the polls, and some information about chemical admixtures was obtained. Compressive strengths of concrete specimens manufactured by ready mixed concrete firms were evaluated, and results were investigated due to different types and proportions of admixtures used in concrete. Chemical admixtures were compared to each other at the ...

  13. A balanced diet is necessary for proper entrainment signals of the mouse liver clock.

    Directory of Open Access Journals (Sweden)

    Akiko Hirao

    Full Text Available BACKGROUND: The peripheral circadian clock in mice is entrained not only by light-dark cycles but also by daily restricted feeding schedules. Behavioral and cell culture experiments suggest an increase in glucose level as a factor in such feeding-induced entrainment. For application of feeding-induced entrainment in humans, nutrient content and dietary variations should be considered. PRINCIPAL FINDING: To elucidate the food composition necessary for dietary entrainment, we examined whether complete or partial substitution of dietary nutrients affected phase shifts in liver clocks of mice. Compared with fasting mice or ad libitum fed mice, the liver bioluminescence rhythm advanced by 3-4 h on the middle day in Per2::luciferase knock-in mice that were administered a standard mouse diet, i.e. AIN-93M formula [0.6-0.85 g/10 g mouse BW] (composition: 14% casein, 47% cornstarch, 15% gelatinized cornstarch, 10% sugar, 4% soybean oil, and 10% other [fiber, vitamins, minerals, etc.], for 2 days. When each nutrient was tested alone (100% nutrient, an insignificant weak phase advance was found to be induced by cornstarch and soybean oil, but almost no phase advance was induced by gelatinized cornstarch, high-amylose cornstarch, glucose, sucrose, or casein. A combination of glucose and casein without oil, vitamin, or fiber caused a significant phase advance. When cornstarch in AIN-93M was substituted with glucose, sucrose, fructose, polydextrose, high-amylose cornstarch, or gelatinized cornstarch, the amplitude of phase advance paralleled the increase in blood glucose concentration. CONCLUSIONS: Our results strongly suggest the following: (1 balanced diets containing carbohydrates/sugars and proteins are good for restricted feeding-induced entrainment of the peripheral circadian clock and (2 a balanced diet that increases blood glucose, but not by sugar alone, is suitable for entrainment. These findings may assist in the development of dietary

  14. Numerical Investigation of Entrainment of Turbulent Dense Currents

    Science.gov (United States)

    Bhaganaagar, Kiran; Nayamatulla, Manjure

    2016-04-01

    Entrainment in dense overflows has fundamental importance for understanding the transport of densest water in the ocean. Estimation of entrainment is extremely challenging and to-date we do not have a fundamental framework that parameterizes entrainment. A highly accurate direct numerical simulation and large eddy simulation solvers have been developed to simulate dense currents over range of smooth- and rough-surfaces. Simulations have been performed for both lock-exchange currents and constant flux currents. A mathematical framework has been developed to estimate entrainment of 2-D and 3-D dense currents. Entrainment has been calculated from first-principles as the relative change in the volume of the dense current in time with respect to the buoyancy forcing that drives the dense current. A combination of threshold method, wherein the height of current is evaluated as height corresponding to the specified threshold value and sorting method, wherein, the mixed fluid is sorted into bins ranging from dense fluid at the bottom to ambient fluid at the top has been used to evaluate the interface between the dense and ambient fluid. Entrainment is sensitive to the method of evaluation of the interface height. Finally, we obtained the dependency of entrainment parameter on non-dimensional parameters. Analysis has demonstrated lock-exchange currents have less mixing and entrainment for same Reynolds number and Froude's number than constant flux currents. The differences exist due to differences in nature of Kelvin-Helmholtz instabilities and lobe-cleft currents. Rough-bottom surfaces introduces additional dynamics of the dense currents. The spacing between the roughness elements has demonstrated to be important metric in entrainment parameters for lock-exchange currents. Densely spaced (D-type) currents travel slower as roughness causes hindrance on density current propagation due to enhanced drag and produces additional eddies and instabilities compared to sparsely

  15. Gas entrainment issues in sodium cooled fast reactors

    International Nuclear Information System (INIS)

    Highlights: • Main sources of gas and related issues in SFR are presented. • Various approaches of gas transport are briefly described. • Previous experimental studies to reduce gas entrainment are reported. • Present evaluation of free surface gas entrainment is presented. - Abstract: Sodium cooled fast reactors have been developed in France for nearly 50 years. The so-called Astrid technology demonstrator is currently designed in the frame of Generation IV deployment. Gas entrainment in the primary sodium circuit is a key issue as it can lead to safety problems in case of accumulation and transport of large quantity of gas through the core. The paper first introduces the main problems caused by the presence of gas in the primary sodium circuit, the various sources of gas and the main issues on gas transport. As sodium–argon free surface is potentially an important source of gas entrainment in the primary circuit, we present the main results obtained in past experimental studies on vortex type gas entrainment at free surface. Water tests were performed in a simple flow condition to study the physical process of vortex occurrence and gas entrainment. Other water tests were performed in representative hot pool models at different scales to analyze similarity criteria. Moreover, design improvements and local devices were tested to avoid gas entrainment at the free surface. Nowadays, numerical tools are progressively used to estimate the risk of gas entrainment at the free surface. We present the methodology in progress to define local criteria on vortex occurrence and gas entrainment, and to apply these criteria to global calculations of the whole pool. A Front-Tracking method coupled to a Large Eddy Simulation approach is implemented in TRIOU code to compute free surface instabilities and vortex occurrence. Experimental data from the literature are used to validate the numerical approach and a new test facility called BANGA is in progress at CEA to

  16. Gas entrainment at free surface of liquid, 2

    International Nuclear Information System (INIS)

    The onset conditions of vortex-induced air entrainment were investigated for the suction flow into a vertical drawing pipe in a cylindrical test vessel. It was found that the onset conditions can be represented by the following two types of empirical criteria: Ron = a1.52(H/D)-1.52 for large Fr, Frn = c0.847(H/D)-0.84 for large Ro, (a = 1.9 x 10-4/D, c = 0.14/D), where D is the inner diameter of the suction pipe in the unit of meter, H the submergence, Fr the Froude number (= V12/gH), and Ro the rotational Froude number (= C∞2/gH3). The subscript n on Ro and Fr denotes the onset correlations derived independently from the relation between Ro and H/D and the relation between Fr and H/D. From visual observation and theoretical consideration, it was found that the above two criteria come from the fact that the onset conditions are dominated by the following two factors: whether the air core formed by vortex reaches the pipe, and whether the water flow in the suction pipe is fast enough for the flow to draw bubbles downward. By combing the two onset criteria into single correlation and comparing it with experimental data, the following correlation was derived, log10(Fr/Frn)log10(Ro/Ron) = h, ( h = 5.71 x 10-4(H/D)1.54). It was confirmed that this correlation represents all the experimental data well. (author)

  17. Simulation of atmosphere entrainment by a single spray with the lumped-parameter code COCOSYS

    International Nuclear Information System (INIS)

    Containment spray systems are possible severe accident management measures against the pressurisation of the containment during loss of coolant accident scenarios. If hydrogen is generated by the oxidation of the cladding tubes and carried into the containment through the leakage, critical concentrations cause the formation of inflammable gas mixtures hazarding the containment integrity. As containment sprays mix the atmosphere by entrainment, which is caused by transferring momentum from the spray droplets to the gaseous environment, local hydrogen concentrations and inflammable gas mixtures are influenced. At Ruhr-Universitaet Bochum a correlation based model for the simulation of spray entrainment using the Containment Code System COCOSYS is developed. The quality of the results is assessed by the comparison of simulation results of the OECD SETH-2 ST3 test series to the experiment values. The 4 tests of this series differ in the atmosphere composition of air and steam. The results related to the gas distribution indicate an improvement of the quality of the results. In particular, the influence of the atmosphere composition on the simulation results is reduced by the consideration of spray entrainment. (orig.)

  18. Improvement of liquid droplet entrainment model in the COBRA-TF code

    International Nuclear Information System (INIS)

    The COBRA-TF liquid droplet entrainment models have been assessed and improved through various experiments. The COBRA-TF code uses the Wurtz entrainment model in the film mist flow regime and the mechanistic model based on the critical Weber number and critical vapor velocity in the hot wall flow regimes, respectively. The Wurtz model has been replaced with the modified Sugawara model. The assessment against the experiments by Hewitt, Keeys, Yanai, and Whalley showed the modified Sugawara model better predicts the steam-water as well as the air-water experiments for the film mist flow regime. For hot wall flow regime, the COBRA-TF entrainment model was modified using two methods, one with an increased critical Weber number and the other with the Yonomoto's critical vapor velocity model. The modified models were assessed using the FLECHT-SEASET bottom reflood tests. The results showed that the Yonomoto model best predicts the quenching time, whereas the local maximum rod temperature was not affected much. (author)

  19. Used cooking oil as a green chemical admixture in concrete

    International Nuclear Information System (INIS)

    According to National Statistics Approximately 1.35 billion gallons of used oil are generated yearly. With the increasing of the concrete usage, a more cost effective and economic new type of admixtures may give positive impacts on the Malaysian construction building as well as worldwide concrete usage. To objective of this is study is to investigate the effect of used cooking oil in terms of slump test, compressive strength test and rebound hammer. By adding the used cooking oil to the concrete, it increases the slump value from 4% to 72%. And the compressive strength have an increment from 1% to 16.8%. The used cooking oil obtains the optimum contribution to the concrete mix proportion of containing used cooking oil of 1.50% from the cement content. The result of used cooking oil from experimental program of slump value and compressive strength proved that used cooking oil have positive effects on replacement of commercially available superplasticizer.

  20. Used cooking oil as a green chemical admixture in concrete

    Science.gov (United States)

    Salmia, B.; Che Muda, Zakaria; Ashraful Alam, Md; Sidek, L. M.; Hidayah, B.

    2013-06-01

    According to National Statistics Approximately 1.35 billion gallons of used oil are generated yearly. With the increasing of the concrete usage, a more cost effective and economic new type of admixtures may give positive impacts on the Malaysian construction building as well as worldwide concrete usage. To objective of this is study is to investigate the effect of used cooking oil in terms of slump test, compressive strength test and rebound hammer. By adding the used cooking oil to the concrete, it increases the slump value from 4% to 72%. And the compressive strength have an increment from 1% to 16.8%. The used cooking oil obtains the optimum contribution to the concrete mix proportion of containing used cooking oil of 1.50% from the cement content. The result of used cooking oil from experimental program of slump value and compressive strength proved that used cooking oil have positive effects on replacement of commercially available superplasticizer.

  1. Techniques and methods of characterization of admixtures for the concrete

    Directory of Open Access Journals (Sweden)

    Palacios, M.

    2003-03-01

    Full Text Available Admixtures are defined as those products that are incorporated in the moment of the process of mixture of the concrete in a quantity not bigger than 5 by mass of the cement %, with relationship to the cement content in the concrete, with object of modifying the properties of the mixture in .state fresh and/or hardened. The behaviour of the admixtures depends on its chemical and ionic composition, the organic functional groups present, and the structure of the polymer and the distribution of molecular weight of the different polymers. In the present work the techniques and methods of characterization physical-chemistry, chemistry and ionic, structural, as well as of the polymers that constitute this admixtures, are described. A lot of techniques have been employed like: ionic chromatography, ultraviolet-visible spectroscopy (UV-VIS, Fourier transform infrared spectroscopy (FTIR, Fourier transform Raman spectroscopy (FT-Raman, nuclear magnetic resonance spectroscopy (1H-RMN and 13C-RMN, gel permeation chromatography (GPC. Two commercial admixtures have been selected to carry out this characterization, a superplastificant based on policarboxilates, and a reducer of the shrinkage based on polipropilenglycol.

    RESUMEN Se definen los aditivos como aquellos productos que son incorporados en el momento del amasado del hormigón en una cantidad no mayor del 5% en masa, con relación al contenido de cemento en el hormigón, con objeto de modificar las propiedades de la mezcla en estado fresco y/o endurecido. El comportamiento de los aditivos depende de su composición química e iónica, de los grupos funcionales orgánicos presentes, de la estructura del polímero y de la distribución de pesos moleculares de los diferentes polímeros que lo constituyen. En el presente trabajo se describen diferentes técnicas y métodos de caracterización físico-química, química e iónica, estructural, así como de los polímeros que

  2. On the maximum grain size entrained by photoevaporative winds

    CERN Document Server

    Hutchison, Mark A; Maddison, Sarah T

    2016-01-01

    We model the behaviour of dust grains entrained by photoevaporation-driven winds from protoplanetary discs assuming a non-rotating, plane-parallel disc. We obtain an analytic expression for the maximum entrainable grain size in extreme-UV radiation-driven winds, which we demonstrate to be proportional to the mass loss rate of the disc. When compared with our hydrodynamic simulations, the model reproduces almost all of the wind properties for the gas and dust. In typical turbulent discs, the entrained grain sizes in the wind are smaller than the theoretical maximum everywhere but the inner disc due to dust settling.

  3. Gas entrainment induced by vortex behind an obstacle

    International Nuclear Information System (INIS)

    In this paper gas entrainment by vortex is studied, which can occur in the vessel of FBR demonstration reactor. In this case the effect of horizontal flow and complicated boundary in it becomes very important to the gas entrainment. Therefore we mainly focused on the geometric conditions and then performed fundamental experiments using water flow with a semicylindrical obstacle. The experimental results show that the relative locations of obstacle and outlet affects the pattern of flow and gas entrainment, which is categorized into four cases. A two-dimensional numerical analysis is also performed to investigate the flow pattern, where the outlet is taken into account. (author)

  4. Genetic admixture and population substructure in Guanacaste Costa Rica.

    Directory of Open Access Journals (Sweden)

    Zhaoming Wang

    Full Text Available The population of Costa Rica (CR represents an admixture of major continental populations. An investigation of the CR population structure would provide an important foundation for mapping genetic variants underlying common diseases and traits. We conducted an analysis of 1,301 women from the Guanacaste region of CR using 27,904 single nucleotide polymorphisms (SNPs genotyped on a custom Illumina InfiniumII iSelect chip. The program STRUCTURE was used to compare the CR Guanacaste sample with four continental reference samples, including HapMap Europeans (CEU, East Asians (JPT+CHB, West African Yoruba (YRI, as well as Native Americans (NA from the Illumina iControl database. Our results show that the CR Guanacaste sample comprises a three-way admixture estimated to be 43% European, 38% Native American and 15% West African. An estimated 4% residual Asian ancestry may be within the error range. Results from principal components analysis reveal a correlation between genetic and geographic distance. The magnitude of linkage disequilibrium (LD measured by the number of tagging SNPs required to cover the same region in the genome in the CR Guanacaste sample appeared to be weaker than that observed in CEU, JPT+CHB and NA reference samples but stronger than that of the HapMap YRI sample. Based on the clustering pattern observed in both STRUCTURE and principal components analysis, two subpopulations were identified that differ by approximately 20% in LD block size averaged over all LD blocks identified by Haploview. We also show in a simulated association study conducted within the two subpopulations, that the failure to account for population stratification (PS could lead to a noticeable inflation in the false positive rate. However, we further demonstrate that existing PS adjustment approaches can reduce the inflation to an acceptable level for gene discovery.

  5. Organic Entrainment and Preservation in Volcanic Glasses

    Science.gov (United States)

    Wilhelm, Mary Beth; Ojha, Lujendra; Brunner, Anna E.; Dufek, Josef D.; Wray, James Joseph

    2014-01-01

    Unaltered pyroclastic deposits have previously been deemed to have "low" potential for the formation, concentration and preservation of organic material on the Martian surface. Yet volcanic glasses that have solidified very quickly after an eruption may be good candidates for containment and preservation of refractory organic material that existed in a biologic system pre-eruption due to their impermeability and ability to attenuate UV radiation. Analysis using NanoSIMS of volcanic glass could then be performed to both deduce carbon isotope ratios that indicate biologic origin and confirm entrainment during eruption. Terrestrial contamination is one of the biggest barriers to definitive Martian organic identification in soil and rock samples. While there is a greater potential to concentrate organics in sedimentary strata, volcanic glasses may better encapsulate and preserve organics over long time scales, and are widespread on Mars. If volcanic glass from many sites on Earth could be shown to contain biologically derived organics from the original environment, there could be significant implications for the search for biomarkers in ancient Martian environments.

  6. Granular motions near the threshold of entrainment

    Science.gov (United States)

    Valyrakis, Manousos; Alexakis, athanasios-Theodosios

    2016-04-01

    Our society is continuously impacted by significant weather events many times resulting in catastrophes that interrupt our normal way of life. In the context of climate change and increasing urbanisation these "extreme" hydrologic events are intensified both in magnitude and frequency, inducing costs of the order of billions of pounds. The vast majority of such costs and impacts (even more to developed societies) are due to water related catastrophes such as the geomorphic action of flowing water (including scouring of critical infrastructure, bed and bank destabilisation) and flooding. New tools and radically novel concepts are in need, to enable our society becoming more resilient. This presentation, emphasises the utility of inertial sensors in gaining new insights on the interaction of flow hydrodynamics with the granular surface at the particle scale and for near threshold flow conditions. In particular, new designs of the "smart-sphere" device are discussed with focus on the purpose specific sets of flume experiments, designed to identify the exact response of the particle resting at the bed surface for various below, near and above threshold flow conditions. New sets of measurements are presented for particle entrainment from a Lagrangian viewpoint. Further to finding direct application in addressing real world challenges in the water sector, it is shown that such novel sensor systems can also help the research community (both experimentalists and computational modellers) gain a better insight on the underlying processes governing granular dynamics.

  7. Music and emotions: from enchantment to entrainment.

    Science.gov (United States)

    Vuilleumier, Patrik; Trost, Wiebke

    2015-03-01

    Producing and perceiving music engage a wide range of sensorimotor, cognitive, and emotional processes. Emotions are a central feature of the enjoyment of music, with a large variety of affective states consistently reported by people while listening to music. However, besides joy or sadness, music often elicits feelings of wonder, nostalgia, or tenderness, which do not correspond to emotion categories typically studied in neuroscience and whose neural substrates remain largely unknown. Here we review the similarities and differences in the neural substrates underlying these "complex" music-evoked emotions relative to other more "basic" emotional experiences. We suggest that these emotions emerge through a combination of activation in emotional and motivational brain systems (e.g., including reward pathways) that confer its valence to music, with activation in several other areas outside emotional systems, including motor, attention, or memory-related regions. We then discuss the neural substrates underlying the entrainment of cognitive and motor processes by music and their relation to affective experience. These effects have important implications for the potential therapeutic use of music in neurological or psychiatric diseases, particularly those associated with motor, attention, or affective disturbances. PMID:25773637

  8. A comparative efficacy study of photic driving brainwave entrainment technology with a novel form of more direct entrainment

    Science.gov (United States)

    Knowles, Richard Thomas

    This exploratory study compared the efficacy of a novel brainwave electromagnetic (EM) entrainment technology against a more conventional technology utilizing the photic-driving technique. Both experimental conditions were also compared with a 7-minute control session that took place immediately before each stimulation session. The Schumann Resonance (SR) frequency was selected as the delivery signal and was chosen because of previous findings suggesting that entrainment to this frequency can often produce transpersonal if not paranormal, experiences in the entrainee, which sometimes resemble remote viewing or out-of-body experiences. A pilot study determined which of two novel entrainment modalities (a copper coil or a 16-solenoid headset) worked most effectively for use with the rest of the study. In the main study, an artificial SR signal at 7.8Hz was delivered during the photic-driving sessions, but a recording of the real-time SR was used to deliver the entrainment signal during sessions devoted to the electromagnetic entrainment modality. Sixteen participants were recruited from the local area, and EEG recordings were acquired via a 32-channel Deymed electroencephalography system. Comparative analyses were performed between the control and experimental portions of each session to assess for efficacy of the novel entrainment modality used, and, in the main study, between the electromagnetic and photic-driving sessions, to assess for differential entrainment efficacy between these groups. A follow-up study was additionally performed primarily to determine whether responders could replicate their entrainment effect from the main study. Results showed that EM entrainment appeared to be possible but is not nearly as robust or reliable as photic driving. Additionally, no profound transpersonal or paranormal experiences were elicited during the course of the study, and, when asked, participants were not able to determine with any degree of success, when the

  9. The Complex Admixture History and Recent Southern Origins of Siberian Populations.

    Science.gov (United States)

    Pugach, Irina; Matveev, Rostislav; Spitsyn, Viktor; Makarov, Sergey; Novgorodov, Innokentiy; Osakovsky, Vladimir; Stoneking, Mark; Pakendorf, Brigitte

    2016-07-01

    Although Siberia was inhabited by modern humans at an early stage, there is still debate over whether it remained habitable during the extreme cold of the Last Glacial Maximum or whether it was subsequently repopulated by peoples with recent shared ancestry. Previous studies of the genetic history of Siberian populations were hampered by the extensive admixture that appears to have taken place among these populations, because commonly used methods assume a tree-like population history and at most single admixture events. Here we analyze geogenetic maps and use other approaches to distinguish the effects of shared ancestry from prehistoric migrations and contact, and develop a new method based on the covariance of ancestry components, to investigate the potentially complex admixture history. We furthermore adapt a previously devised method of admixture dating for use with multiple events of gene flow, and apply these methods to whole-genome genotype data from over 500 individuals belonging to 20 different Siberian ethnolinguistic groups. The results of these analyses indicate that there have been multiple layers of admixture detectable in most of the Siberian populations, with considerable differences in the admixture histories of individual populations. Furthermore, most of the populations of Siberia included here, even those settled far to the north, appear to have a southern origin, with the northward expansions of different populations possibly being driven partly by the advent of pastoralism, especially reindeer domestication. These newly developed methods to analyze multiple admixture events should aid in the investigation of similarly complex population histories elsewhere. PMID:26993256

  10. A factorial design study on the physical stability of 3-in-1 admixtures.

    Science.gov (United States)

    Li, L C; Sampogna, T P

    1993-11-01

    The effects of dextrose concentration, the compounding method, and storage conditions, on the physical stability of 3-in-1 admixtures were investigated using a 2n factorial design. The main effect of these three variables on the weight percent of oil globules larger than 5 microns (by HIAC) was found to be statistically significant. However, the effects of interaction amongst these variables, except the two-way interaction between dextrose concentration and storage conditions, were found to be statistically insignificant. A higher dextrose concentration was shown to enhance the physical stability of the admixtures, while low-temperature storage (three days at 5 degrees C) was more favourable for maintaining the physical stability of the admixtures with a low dextrose concentration. Although sequential pumping produced admixtures with a slightly lower final weight percentage of larger oil globules (> 5 microns), the method of compounding has the least impact on the physical stability of the admixtures in comparison with the other two variables evaluated in this study. The storage of the admixtures at room temperature for one day was shown to have a greater adverse effect on admixtures with a low dextrose concentration. PMID:7908042

  11. Drop size measurements and entrainment in APR1400 during LBLOCA reflood phase

    International Nuclear Information System (INIS)

    A study has been performed to investigate droplet size in the nuclear reactor of APR1400 during LBLOCA reflood phase and to develop droplet entrainment and deposition models for SPACE (Safety and Performance CodE) which is a safety analysis tool for PWR being developed in Korea. A freezing technique for measuring the size of droplets was developed to obtain the droplet size distribution in horizontal annular flow in a pipe with a 37.1 mm diameter. Droplets are frozen by using an extremely low temperature nitrogen gas with liquid film extraction. They are then photographed with a microscope and a CCD camera and measured by means of an image process. The results are compared with various experimental data. The droplet sizes measured by the freezing technique are comparable with those measured by other methods at a high superficial air velocity (of 50 m/s). However, because of the film extraction problem, the droplet sizes measured at a low superficial air velocity of less than 40 m/s are higher than those measured by other methods. A present method suggested for predicting the Sauter mean diameter is based on the maximum droplet size correlation for the experimental data, with and without liquid film extraction. The average droplet size is remarkably smaller downstream of the liquid film extractor because large droplets from the liquid film are excluded. In order to understand and to predict a heat transfer between superheated steam and droplets properly during reflood phase of LBLOCA, it is very important to measure broken droplet sizes by spacer grids. A study, therefore, has been performed to investigate droplet size in rod bundles with spacer grids and to develop a spacer grid droplet breakup model for safety analysis codes. Experiments were conducted with liquid droplets (SMD of 300∼700 μm) and various spacer grids at superficial air velocity of 10 m/s and 20 m/s based on FLECHT SEASET. The test channel and the grids were heated to 150 .deg. C to prevent

  12. Finding new solutions in pediatric parenteral admixtures: how to improve quality and to deal with shortages

    Directory of Open Access Journals (Sweden)

    Dorota Watrobska-Swietlikowska

    2014-07-01

    Full Text Available Introduction: Pediatric parenteral nutrition enables normal growth even of preterm infants. Those children require, however, tailored parenteral nutrition and the creation of such can be challenging due to the risk of instability and shortages. Objective: Prototypical parenteral admixtures were created using different calcium salts (organic and inorganic and different lipid emulsions and tested for stability. 36 of parenteral admixtures containing two types of calcium salts: chloride or gluconolactobionate and different lipid emulsions (SMOFlipid® or Lipofundin MCT/LCT® were under investigation. Methods: Preliminary admixtures were prepared in two-chamber bags whereas lipid emulsions were placed separately in the second chamber. Pre-admixtures were stored for up to 21 days at +4ºC. Contents of the two chambers were combined at t = 0 or after 21 days of storage. Physical analysis of completed admixtures (visual inspection, microscopic observation, pH measurement and determination of the size distribution of oily droplets was carried out after 21 days of the storage. Stability of lipid, commercial emulsions stored in ethylene vinyl acetate (EVA bags for 42 days was also studied. Results: Irrespectively of the time of storage of preadmixtures and type of calcium salt and different lipid emulsions among 36 total parenteral admixtures only one showed signs of destabilization after preparation and one was unstable when stored for longer than 14 days. All other formulations were qualified to be stable during the study. All investigated commercial lipid emulsions were physically stable in EVA bags even when stored at room temperature. Conclusion: The study proved that it was possible to store pre-admixture in EVA bags for 21 days at 4ºC as well as that CAN (critical aggregation number and CaxP (the products of multiplication of calcium and phosphate ions concentration should not be used as reliable indicators of admixture physical stability. No

  13. Liquid transfer and entrainment correlation for droplet-annular flow

    International Nuclear Information System (INIS)

    A correlation for the amount of entrained liquid in annular flow has been developed from a simple model and experimental data. There are basically two different regions of entrainment, namely, the entrance and quasi-equilibrium regions. The correlation for the equilibrium region is expressed in terms of the dimensionless gas flux, diameter, cand total liquid Reynolds number. The entrance effect is taken into account by an exponential relaxation function. It has been shown that this new model can satisfactorily correlate wide ranges of experimental data for water. Furthermore, the necessary distance for the development of entrainment is identified. These correlations, therefore, can supply accurate information on entrainment which has not been available previously

  14. Entrainment of a Synthetic Oscillator through Queueing Coupling

    Science.gov (United States)

    Hochendoner, Philip; Mather, William; Butzin, Nicholas; Ogle, Curtis

    2014-03-01

    Many biological systems naturally exhibit (often noisy) oscillatory patterns that are capable of being entrained by external stimuli, though the mechanism of entrainment is typically obscured by the complexity of native networks. A synthetic biology approach, where genetic programs are wired ``by hand,'' has proven useful in this regard. In the present study, we use a synthetic oscillator in Escherichia coli to demonstrate a novel and potentially widespread mechanism for biological entrainment: competition of proteins for degradation by common pathway, i.e. a entrainment by a bottleneck. To faithfully represent the discrete and stochastic nature of this bottleneck, we leverage results from a recent biological queueing theory, where in particular, the queueing theoretic concept of workload is discovered to simplify the analysis. NSF Award 1330180.

  15. Experimental investigation on bubble characteristics entrained by surface vortex

    International Nuclear Information System (INIS)

    The cover gas entrainment at the free surface of sodium coolant becomes one of the significant issues according to the compact sizing of reactor vessel in the latest reactor design. In the present study, some basic experiments for the gas entrainment due to the surface vortex were performed in order to obtain the fundamental knowledge about the entrained bubble size. Distributions of entrained bubble diameters in several experimental conditions were obtained from bubble images using an image processing technique. Velocity fields around vortices and surface dimple shapes (gas cores) due to surface vortices were measured to grasp those influences on bubble shapes. The result showed that mean equivalent diameters of bubbles were varied from 1.3 to 2.1 mm in the range of present experimental conditions. The bubble sizes were influenced by the thickness of gas core.

  16. Differential entrainment of neuroelectric delta oscillations in developmental dyslexia.

    Directory of Open Access Journals (Sweden)

    Fruzsina Soltész

    Full Text Available Oscillatory entrainment to the speech signal is important for language processing, but has not yet been studied in developmental disorders of language. Developmental dyslexia, a difficulty in acquiring efficient reading skills linked to difficulties with phonology (the sound structure of language, has been associated with behavioural entrainment deficits. It has been proposed that the phonological 'deficit' that characterises dyslexia across languages is related to impaired auditory entrainment to speech at lower frequencies via neuroelectric oscillations (<10 Hz, 'temporal sampling theory'. Impaired entrainment to temporal modulations at lower frequencies would affect the recovery of the prosodic and syllabic structure of speech. Here we investigated event-related oscillatory EEG activity and contingent negative variation (CNV to auditory rhythmic tone streams delivered at frequencies within the delta band (2 Hz, 1.5 Hz, relevant to sampling stressed syllables in speech. Given prior behavioural entrainment findings at these rates, we predicted functionally atypical entrainment of delta oscillations in dyslexia. Participants performed a rhythmic expectancy task, detecting occasional white noise targets interspersed with tones occurring regularly at rates of 2 Hz or 1.5 Hz. Both groups showed significant entrainment of delta oscillations to the rhythmic stimulus stream, however the strength of inter-trial delta phase coherence (ITC, 'phase locking' and the CNV were both significantly weaker in dyslexics, suggestive of weaker entrainment and less preparatory brain activity. Both ITC strength and CNV amplitude were significantly related to individual differences in language processing and reading. Additionally, the instantaneous phase of prestimulus delta oscillation predicted behavioural responding (response time for control participants only.

  17. Entrainment Ranges for Chains of Forced Neural and Phase Oscillators.

    Science.gov (United States)

    Massarelli, Nicole; Clapp, Geoffrey; Hoffman, Kathleen; Kiemel, Tim

    2016-12-01

    Sensory input to the lamprey central pattern generator (CPG) for locomotion is known to have a significant role in modulating lamprey swimming. Lamprey CPGs are known to have the ability to entrain to a bending stimulus, that is, in the presence of a rhythmic signal, the CPG will change its frequency to match the stimulus frequency. Bending experiments in which the lamprey spinal cord has been removed and mechanically bent back and forth at a single point have been used to determine the range of frequencies that can entrain the CPG rhythm. First, we model the lamprey locomotor CPG as a chain of neural oscillators with three classes of neurons and sinusoidal forcing representing edge cell input. We derive a phase model using the connections described in the neural model. This results in a simpler model yet maintains some properties of the neural model. For both the neural model and the derived phase model, entrainment ranges are computed for forcing at different points along the chain while varying both intersegmental coupling strength and the coupling strength between the forcer and chain. Entrainment ranges for chains with nonuniform intersegmental coupling asymmetry are larger when forcing is applied to the middle of the chain than when it is applied to either end, a result that is qualitatively similar to the experimental results. In the limit of weak coupling in the chain, the entrainment results of the neural model approach the entrainment results for the derived phase model. Both biological experiments and the robustness of non-monotonic entrainment ranges as a function of the forcing position across different classes of CPG models with nonuniform asymmetric coupling suggest that a specific property of the intersegmental coupling of the CPG is key to entrainment. PMID:27091694

  18. Gas entrainment induced by vortex behind an obstacle. 2

    International Nuclear Information System (INIS)

    In the previous study gas entrainment by vortex is studied using semicylindrical a obstacle. In that case, flow patterns were categorized into four cases. In this study we perform fundamental experiments using with a cylindrical obstacle. The experimental results show that the relative locations of the obstacle, outlet and wall affects the patterns of flow and gas entrainment, which are categorized into six cases due to antisymmetry in the geometry. (author)

  19. Numerical analysis of the effect of nitrogen and oxygen admixtures on the chemistry of an argon plasma jet operating at atmospheric pressure

    Science.gov (United States)

    Van Gaens, W.; Iseni, S.; Schmidt-Bleker, A.; Weltmann, K.-D.; Reuter, S.; Bogaerts, A.

    2015-03-01

    In this paper we study the cold atmospheric pressure plasma jet, called kinpen, operating in Ar with different admixture fractions up to 1% pure {{N}2}, {{O}2} and {{N}2} + {{O}2}. Moreover, the device is operating with a gas curtain of dry air. The absolute net production rates of the biologically active ozone ({{O}3}) and nitrogen dioxide (N{{O}2}) species are measured in the far effluent by quantum cascade laser absorption spectroscopy in the mid-infrared. Additionally, a zero-dimensional semi-empirical reaction kinetics model is used to calculate the net production rates of these reactive molecules, which are compared to the experimental data. The latter model is applied throughout the entire plasma jet, starting already within the device itself. Very good qualitative and even quantitative agreement between the calculated and measured data is demonstrated. The numerical model thus yields very useful information about the chemical pathways of both the {{O}3} and the N{{O}2} generation. It is shown that the production of these species can be manipulated by up to one order of magnitude by varying the amount of admixture or the admixture type, since this affects the electron kinetics significantly at these low concentration levels.

  20. EFFECTS OF CHEMICAL ADMIXTURES ON SPECIALITIES OF HARDENED CONCRETE USED IN READY CONCRETE PRODUCTION IN ESKİŞEHİR

    Directory of Open Access Journals (Sweden)

    İlker Bekir TOPÇU

    2006-01-01

    Full Text Available In this study polls were taken from different ready mixed concrete firms in Eskişehir. Chemical admixtures used in concrete production were investigated according to the polls, and some information about chemical admixtures was obtained. Compressive strengths of concrete specimens manufactured by ready mixed concrete firms were evaluated, and results were investigated due to different types and proportions of admixtures used in concrete. Chemical admixtures were compared to each other at the end of the investigation, and the results showed, chemical admixtures gain concrete different characteristics according to various environmental conditions. The past investigations showed that the differences between chemical admixtures were most occurred owing to environmental conditions (season, temperature etc., and chemical admixtures were classified according to seasons by users.

  1. COP Evaluation for a Membrane Liquid Desiccant Air Conditioning System Using Four Different Heating Equipment

    OpenAIRE

    Abdel-Salam, Ahmed; Simonson, Carey

    2015-01-01

    Liquid desiccant air conditioning (LDAC) is a promising technology in terms of energy efficiency, comfort and indoor air quality. The major components of a LDAC system are the dehumidifier and regenerator. The most commonly used design of dehumidifiers/regenerators is the packed-bed, which might result in the entrainment of desiccant droplets in air streams. A promising solution for the entrainment of desiccant droplets in air streams is to use a liquid-to-air membrane energy exchanger (LAMEE...

  2. Entrainment and detrainment in a simple cumulus cloud model

    Science.gov (United States)

    Randall, D. A.; Huffman, G. J.

    1982-01-01

    A cumulus cloud model, analogous to the mixed-layer models of the planetary boundary layer and the upper ocean, is developed using a single, unitary entrainment process in which the motion of the cloud boundary relative to the mean flow is permitted, produced, and controlled by turbulent processes. An alternate theory to the mixing-length theory of Asai and Kasahara (1967) is proposed which completely removes the strong scale-dependence of the Asai-Kasahara model. The model reintroduces scale-dependence by introducing including the pe5turbation pressure term of the equation of vertical motion. It is shown that the model predicts deeper clouds than the Asai-Kasahara model for a given sounding, due to the entrainment assumption and the effects of the perturbation pressure. Lateral entrainment dominates cloud-top entrainment, although finite-difference errors increase the cloud-top entrainment rate from zero to a positive value in actual situations. The fractional entrainment rate for updrafts is determined to vary only slightly with height and to decrease only slowly as the cloud radius increases, while the fractional detrainment rate for updrafts increases with height.

  3. Effect of polycarboxylate admixture structure on cement paste rheology

    Directory of Open Access Journals (Sweden)

    Aranda, M. A. G.

    2007-06-01

    Full Text Available The purpose of the present study was to analyze the effect of the structural differences in four polycarboxylate and polyether admixtures on the rheological properties of cement pastes with different chemical and mineralogical compositions and different active additions (CEM I 42.5 R, CEM I 52.5 R, CEM I 52.5 N/SR, CEM II/AV 42.5R, CEM II/B-L 32.5 R, CEM III/B 32.5R, BL I 52.5R and CAC – European standard EN 197-1:2000. The results of the minislump test concurred with the variations observed in the values of the rheological parameters (shear stress and plastic viscosity. The structural characteristic of the admixtures found to play the most prominent role in their fluidizing effect was the proportion of carboxylate (CG and polyether (EG group components. In cements characteristics such as fineness and the C3A/calcium sulphate and C3S/C3A ratios were also observed to be essential to admixture effectiveness. In this regard, the rheological parameters varied most widely in CEM I 52.5N/SR pastes and least in BL I 52.5R cement pastes. Of the additioned cements, the CEM III/B 32.5R pastes, which contained granulated blast furnace slag, showed the highest rises in flowability. Finally, the fluidizing effect of polycarboxylate superplasticizers was much more intense in calcium aluminate cements, although flowability declined rapidly in this material.El objetivo de este trabajo ha sido estudiar el efecto de las diferencias estructurales de cuatro aditivos basados en policarboxilatos y poliéteres sobre las propiedades reológicas de pastas de cemento con diferente composición química, mineralógica y con distintas adiciones activas (CEM I 42,5 R, CEM I 52,5 R, CEM I 52,5 N/SR, CEM II/AV 42,5R, CEM II/ B-L 32,5 R, CEM III/B 32,5R, BL I 52,5R y CAC - Norma EN 197-1:2000. Los resultados obtenidos sobre la fluidez de la pasta en el ensayo del “Minislump” coinciden con la evolución de los valores de los parámetros reológicos (esfuerzo de

  4. Turning Off Entrainment: The Role of Particle Size Distributions and Vent GeometryIn The Collapse of Volcanic Jets

    Science.gov (United States)

    Jessop, D.; Jellinek, M.; Roche, O.

    2014-12-01

    Volcanic jets can undergo gravitational collapse to produce pyroclastic density currents (PDCs), or loft material several tens of kilometres and spread out as an ash cloud. The key ingredient that determines which of these two phenomena will occur is the turbulent entrainment of atmospheric air, which adds buoyancy to the jet. Classical models of eruption columns assume that the rate of entrainment is fixed and ~10% of the upflow rate of the jet. In particular, the efficiency of entrainment is assumed to be independent of the vent shape as well as the physical properties of the pyroclastic mixture. However, we show that the presence of particles of certain particle-size distributions (PSDs) in the jet can have a significant effect on the entrainment rate owing to their buoyancy and inertia. As a consequence, the conditions for collapse as previously identified must be revisited. In particular, there is a possibility for an eruption to produce both a buoyant column and a collapsing fountain. Using scaled analogue experiments, we test the likelyhood of collapse and the production of pyroclastic flows according to the source geometry and particle-size distributions.

  5. Stability of admixture containing morphine sulfate, bupivacaine hydrochloride, and clonidine hydrochloride in an implantable infusion system.

    Science.gov (United States)

    Classen, Ashley M; Wimbish, Gary H; Kupiec, Thomas C

    2004-12-01

    Intrathecal infusion is often performed using drug combinations. This study was conducted to evaluate the stability of the admixture of morphine sulfate, bupivacaine hydrochloride, and clonidine hydrochloride when used in an implantable pump under simulated clinical use conditions. SynchroMed implantable pumps were filled with an admixture and incubated at 37 degrees C for a period of 90 days. Drug admixture stored in glass vials at 4 degrees C and at 37 degrees C served as controls. Samples which included pump reservoir and catheter delivered aliquots were collected every 30 days and analyzed for drug concentrations using a stability-indicating HPLC method. All drugs contained in the admixture were stable and the original concentrations remained greater than 96%. Over 90 days, and with the pump at the simulated body temperature of 37 degrees C, there were no evident heat catalyzed or device catalyzed reactions. PMID:15589086

  6. Admixture enhanced controlled low-strength material for direct underwater injection with minimal cross-contamination

    International Nuclear Information System (INIS)

    Commercially available admixtures have been developed for placing traditional concrete products under water. This paper evaluates adapting anti-washout admixture (AWA) and high range water reducing admixture (HRWRA) products to enhance controlled low-strength materials (CLSMs) for underwater placement. A simple experimental scale model (based on dynamic and geometric similitude) of typical grout pump emplacement equipment has been developed to determine the percentage of cementing material washed out. The objective of this study was to identify proportions of admixtures and underwater CLSM emplacement procedures which would minimize the cross-contamination of the displaced water while maintaining the advantages of CLSM. Since the displaced water from radioactively contaminated systems must be subsequently treated prior to release to the environment, the amount of cross-contamination is important for cases in which cementing material could form hard sludges in a water treatment facility and contaminate the in-place CLSM stabilization medium

  7. A Genome-Wide Search for Greek and Jewish Admixture in the Kashmiri Population

    Science.gov (United States)

    Tashi, Tsewang; Lorenzo, Felipe Ramos; Feusier, Julie Ellen; Mir, Hyder

    2016-01-01

    The Kashmiri population is an ethno-linguistic group that resides in the Kashmir Valley in northern India. A longstanding hypothesis is that this population derives ancestry from Jewish and/or Greek sources. There is historical and archaeological evidence of ancient Greek presence in India and Kashmir. Further, some historical accounts suggest ancient Hebrew ancestry as well. To date, it has not been determined whether signatures of Greek or Jewish admixture can be detected in the Kashmiri population. Using genome-wide genotyping and admixture detection methods, we determined there are no significant or substantial signs of Greek or Jewish admixture in modern-day Kashmiris. The ancestry of Kashmiri Tibetans was also determined, which showed signs of admixture with populations from northern India and west Eurasia. These results contribute to our understanding of the existing population structure in northern India and its surrounding geographical areas. PMID:27490348

  8. Combined effect of expansive and shrinkage reducing admixtures to obtain stable and durable mortars

    International Nuclear Information System (INIS)

    In order to improve the dimensional stability of cement based mortars, the effects produced on cement hydration of a shrinkage reducer (propyleneglycol ether based-SRA) and an expansive admixture (calcium oxide based-EXP) were investigated. Mortar samples (prepared without admixtures or with SRA or EXP or SRA and EXP) were compared through compressive strength measurements, water evaporation, restrained shrinkage and restrained expansion measurements. Setting time and free expansion were also detected on cement paste specimens. A synergistic effect on the shrinkage reduction was observed when the shrinkage reducing admixture and the expansive agent were used together. In order to clarify this phenomenon, the hydration of cement pastes containing these kinds of admixtures was followed by ESEM-FEG (environmental scanning electron microscopy-field emission gun), TG (thermogravimetry), specific surface area measurements (by BET-Brunauer-Emmet-Teller-method) and XRDS (X-ray diffraction spectroscopy)

  9. $\\Sigma^-$ admixture in the $^{10}_\\Lambda$Li hypernucleus with a repulsive $\\Sigma$-nucleus potential

    CERN Document Server

    Lanskoy, D E

    2013-01-01

    $\\Sigma^-$ hyperon component of the $^{10}_\\Lambda$Li wave function is studied. The $\\Sigma^-$ admixture is vital for production of neutron-rich $\\Lambda$ hypernuclei via mesonic beams. We use a simplified shell model wave function for the $\\Lambda$ channel and calculate the $\\Sigma^-$ admixture directly from coupled equations. Probability of the $\\Sigma^-$ admixture for realistic repulsive $\\Sigma^-$-nucleus potentials is less by several times than that for attractive potentials and does not exceed $0.1\\%$. We conclude that the cross sections of the $^{10}\\mbox{B}(\\pi^-,K^+){}^{10}_\\Lambda\\mbox{Li}$ reaction measured at KEK cannot be explained by production via $\\Sigma^-$ admixture as a doorway state.

  10. Development of a lumped-parameter model for the simulation of spray-induced atmosphere entrainment with the containment code system COCOSYS

    International Nuclear Information System (INIS)

    In this compact, the current state of the spray entrainment model development and calculation results using this model in COCOSYS are presented. The correlation based lumped-parameter model calculates entrainment related atmosphere flows by considering the entrainment induced dynamic pressure. The presented results of the OECD SETH-2 PANDA ST3 tests show, that the use of the model improves the simulation of helium fraction evolutions under the presented atmosphere conditions and simulates physically reasonable flow patterns. The improvement of helium fraction simulation is higher for the tests with pure air/steam atmospheres. In the tests with mixed steam/air content in the atmosphere, the helium fractions calculated without the entrainment model decrease temporally shifted to a value in the same order of magnitude as simulated using the entrainment model due to condensation induced flows. Helium fraction evolutions are relevant for reactor safety applications, as helium can be regarded as a substitute for hydrogen due to its chemical and physical properties. In the frame of further model development, the model will be assessed regarding the simulation of multiple interacting sprays as occurring in containment spray systems. (orig.)

  11. Final Report - "Foaming and Antifoaming and Gas Entrainment in Radioactive Waste Pretreatment and Immobilization Processes"

    Energy Technology Data Exchange (ETDEWEB)

    Wasan, Darsh T.

    2007-10-09

    The Savannah River Site (SRS) and Hanford site are in the process of stabilizing millions of gallons of radioactive waste slurries remaining from production of nuclear materials for the Department of Energy (DOE). The Defense Waste Processing Facility (DWPF) at SRS is currently vitrifying the waste in borosilicate glass, while the facilities at the Hanford site are in the construction phase. Both processes utilize slurry-fed joule-heated melters to vitrify the waste slurries. The DWPF has experienced difficulty during operations. The cause of the operational problems has been attributed to foaming, gas entrainment and the rheological properties of the process slurries. The rheological properties of the waste slurries limit the total solids content that can be processed by the remote equipment during the pretreatment and meter feed processes. Highly viscous material can lead to air entrainment during agitation and difficulties with pump operations. Excessive foaming in waste evaporators can cause carryover of radionuclides and non-radioactive waste to the condensate system. Experimental and theoretical investigations of the surface phenomena, suspension rheology and bubble generation of interactions that lead to foaming and air entrainment problems in the DOE High Level and Low Activity Radioactive Waste separation and immobilization processes were pursued under this project. The first major task accomplished in the grant proposal involved development of a theoretical model of the phenomenon of foaming in a three-phase gas-liquid-solid slurry system. This work was presented in a recently completed Ph.D. thesis (9). The second major task involved the investigation of the inter-particle interaction and microstructure formation in a model slurry by the batch sedimentation method. Both experiments and modeling studies were carried out. The results were presented in a recently completed Ph.D. thesis. The third task involved the use of laser confocal microscopy to study

  12. Numerical study on onset of gas entrainment from free surface

    International Nuclear Information System (INIS)

    Full text of publication follows: A fast breeder nuclear reactor (FBR) has an important role for closing a fuel cycle system in fission nuclear reactor systems. The liquid sodium cooling system of a latest compact FBR concept consists of two loops connected to a heat exchanger (HEX) and a pool-typed reactor vessel with the upper core structures (UCS). The high temperature sodium coolant comes from the reactor core to the vessel and flows through the hot legs towards the HEX. In order to design the compact FBR, it is necessary to clarify a criterion of a cover-gas entrainment from the coolant free surface of the vessel to the HEX through the hot leg. The surface velocity of the coolant in the vessel is considered as one of the key parameters of the gas entrainment phenomena: bubble entrained by free surface vortex, entraining bubbles caused by supercritical flows and gas entrainment by wave breaking. However, there is no clear quantitative explanation and criterion regarding the on-set condition of gas entrainment from the free surface until today. In the present study, numerical simulation of the gas entrainment and the bubble transport from free surface to the hot leg regarding the bubble entrainment due to the supercritical surface flows have been performed by means of the Multi-interface and Advection and Reconstruction Solver (MARS) and the numerical results are compared with that of the small scale fundamental experiments. The final goal of this study is to establish the evaluation procedure and criterion of these phenomena. Experiment performed by Moriya was chosen as the reference data for this comparison study. The test section consisted of an open-upped rectangular box with the inlet and outlet nozzles located at bottom of the box and almost a half height of the test section was filled with water. Resulting from these simulations, the gas entrainment phenomena were observed for both cases at certain flow conditions. In two-dimensional simulations, we found

  13. Effect of alkohols as hardening-accelerating admixtures on the cement properties

    OpenAIRE

    Флейшер, Ганна Юріївна; Токарчук, Володимир Володимирович; Василькевич, Олександр Іванович; Свідерський, Валентин Анатолійович

    2014-01-01

    The effect of alcohols as hardening-accelerating admixtures on physicomechanical properties of cement, particularly strength indexes in early hardening period is investigated. Alcohols can be used as an effective hardening accelerators of cement. The effectiveness of the influence of alcohols on the cement properties depends on their spatial structure and the number of hydroxyl groups. It was found that the largest increase in the cement strength is promoted by individual admixtures of alcoho...

  14. Statistical Tests for Admixture Mapping with Case-Control and Cases-Only Data

    OpenAIRE

    Montana, Giovanni; Pritchard, Jonathan K

    2004-01-01

    Admixture mapping is a promising new tool for discovering genes that contribute to complex traits. This mapping approach uses samples from recently admixed populations to detect susceptibility loci at which the risk alleles have different frequencies in the original contributing populations. Although the idea for admixture mapping has been around for more than a decade, the genomic tools are only now becoming available to make this a feasible and attractive option for complex-trait mapping. I...

  15. Finding new solutions in pediatric parenteral admixtures: how to improve quality and to deal with shortages

    OpenAIRE

    Dorota Watrobska-Swietlikowska; Anna Kwidzynska; Agnieszka Szlagatys-Sidorkiewicz; Malgorzata Sznitowska; Stanislaw Klek

    2014-01-01

    Introduction: Pediatric parenteral nutrition enables normal growth even of preterm infants. Those children require, however, tailored parenteral nutrition and the creation of such can be challenging due to the risk of instability and shortages. Objective: Prototypical parenteral admixtures were created using different calcium salts (organic and inorganic) and different lipid emulsions and tested for stability. 36 of parenteral admixtures containing two types of calcium salts: chloride or gluc...

  16. Diffusion Decay Coefficient for Chloride Ions of Concrete Containing Mineral Admixtures

    OpenAIRE

    Jae-Im Park; Kwang-Myong Lee; Soon-Oh Kwon; Su-Ho Bae; Sang-Hwa Jung; Sung-Won Yoo

    2016-01-01

    The diffusion coefficient for chloride ions and the diffusion decay coefficient for chloride ions are essential variables for a service life evaluation of concrete structures. They are influenced by water-binder ratio, exposure condition, curing temperature, cement type, and the type and use of mineral admixture. Mineral admixtures such as ground granulated blast furnace slag, fly ash, and silica fume have been increasingly used to improve resistance against chloride ions penetration in concr...

  17. Admixture Mapping Identifies a Quantitative Trait Locus Associated with FEV1/FVC in the COPDGene Study

    OpenAIRE

    Parker, Margaret M.; Foreman, Marilyn G; Abel, Haley J.; Rasika A Mathias; Hetmanksi, Jacqueline B.; Crapo, James D.; Silverman, Edwin K.; Terri H Beaty

    2014-01-01

    African Americans are admixed with genetic contributions from European and African ancestral populations. Admixture mapping leverages this information to map genes influencing differential disease risk across populations. We performed admixture and association mapping in 3300 African American current or former smokers from the COPDGene Study. We analyzed estimated local ancestry and SNP genotype information to identify regions associated with FEV1/FVC, the ratio of forced expiratory volume in...

  18. A droplet entrainment model for horizontal segregated flows

    Energy Technology Data Exchange (ETDEWEB)

    Höhne, Thomas, E-mail: T.Hoehne@hzdr.de [Helmholtz-Zentrum Dresden-Rossendorf (HZDR) – Institute of Fluid Dynamics, P.O. Box 510119, D-01314 Dresden (Germany); Hänsch, Susann [Imperial College, Department of Mechanical Engineering, South Kensington Campus, London SW7 2AZ (United Kingdom)

    2015-05-15

    Highlights: • We further developed the flow morphology detection model AIAD. • An advanced droplet entrainment model was introduced. • The new approach is applied against HAWAC experiments. - Abstract: One limitation in simulating horizontal segregated flows is that there is no treatment of droplet formation mechanisms at wavy surfaces. For self-generating waves and slugs, the interfacial momentum exchange and the turbulence parameters have to be modeled correctly. Furthermore, understanding the mechanism of droplet entrainment for heat and mass transfer processes is of great importance in the chemical and nuclear industry. The development of general computational fluid dynamics models is an essential precondition for the application of CFD codes to the modeling of flow related phenomena. The new formulation for the interfacial drag at the free surface and turbulence parameters within the algebraic interfacial area density model (AIAD) represents one step toward a more physical description of free surface flows including less empiricism. The AIAD approach allows the use of different physical models depending on the local fluid morphology inside a macro-scale multi-fluid framework. A further step of improving the modeling of free interfaces lies within the consideration of droplet entrainment mechanisms. In this paper a new sub-grid entrainment model is proposed, which assumes that due to liquid turbulence the interface gets rough and wavy leading to the formation of droplets. Therefore, the droplet entrainment model requires the consideration of an additional droplet phase, which is described with an own set of balance equations in the spirit of the particle model. Two local key factors determine the rate of droplet entrainment: the liquid turbulent kinetic energy as well as the outward velocity gradient of the liquid relative to the interface motion. The new droplet entrainment approach is included into CFD simulations for attempting to reproduce existing

  19. A droplet entrainment model for horizontal segregated flows

    International Nuclear Information System (INIS)

    Highlights: • We further developed the flow morphology detection model AIAD. • An advanced droplet entrainment model was introduced. • The new approach is applied against HAWAC experiments. - Abstract: One limitation in simulating horizontal segregated flows is that there is no treatment of droplet formation mechanisms at wavy surfaces. For self-generating waves and slugs, the interfacial momentum exchange and the turbulence parameters have to be modeled correctly. Furthermore, understanding the mechanism of droplet entrainment for heat and mass transfer processes is of great importance in the chemical and nuclear industry. The development of general computational fluid dynamics models is an essential precondition for the application of CFD codes to the modeling of flow related phenomena. The new formulation for the interfacial drag at the free surface and turbulence parameters within the algebraic interfacial area density model (AIAD) represents one step toward a more physical description of free surface flows including less empiricism. The AIAD approach allows the use of different physical models depending on the local fluid morphology inside a macro-scale multi-fluid framework. A further step of improving the modeling of free interfaces lies within the consideration of droplet entrainment mechanisms. In this paper a new sub-grid entrainment model is proposed, which assumes that due to liquid turbulence the interface gets rough and wavy leading to the formation of droplets. Therefore, the droplet entrainment model requires the consideration of an additional droplet phase, which is described with an own set of balance equations in the spirit of the particle model. Two local key factors determine the rate of droplet entrainment: the liquid turbulent kinetic energy as well as the outward velocity gradient of the liquid relative to the interface motion. The new droplet entrainment approach is included into CFD simulations for attempting to reproduce existing

  20. Development of gas entrainment mitigation devices for PFBR hot pool

    International Nuclear Information System (INIS)

    Highlights: ► Gas entrainment from sodium free surface creates various operational problems in SFR. ► The high free surface velocity causes vortex induced gas entrainment. ► Gas entrainment can be avoided by reducing free surface velocity magnitude. ► Ring type baffle plate has been developed for PFBR to mitigate gas entrainment. ► This paper reports the development of ring type baffle plate in detail. -- Abstract: The phenomenon of argon gas entrainment into primary sodium in the hot pool of a liquid Sodium cooled Fast Reactor (SFR) is investigated. A combined experimental and computational approach is proposed. Physical entrainment of argon into sodium is highly geometry dependent and the present study is focused on the Indian Prototype Fast Breeder Reactor (PFBR). The computational model which is used for parametric studies is validated against a 1/4 scale water model tests. Based on systematic experiments, the free surface velocity for onset of gas entrainment is determined to be 0.32 m/s, and the corresponding threshold value for the surface vorticity has been estimated as 8.3 s−1. A horizontal baffle plate attached to inner vessel is found to reduce the free surface velocity/vorticity effectively. The radial width of the baffle plate and its elevation has been optimized to be 0.125 m and 0.315 m from free surface by computational studies. The optimized device has been tested in the water model to confirm its satisfactory performance before its recommendation for PFBR

  1. A Novel Admixture-Based Pharmacogenetic Approach to Refine Warfarin Dosing in Caribbean Hispanics.

    Directory of Open Access Journals (Sweden)

    Jorge Duconge

    Full Text Available This study is aimed at developing a novel admixture-adjusted pharmacogenomic approach to individually refine warfarin dosing in Caribbean Hispanic patients.A multiple linear regression analysis of effective warfarin doses versus relevant genotypes, admixture, clinical and demographic factors was performed in 255 patients and further validated externally in another cohort of 55 individuals.The admixture-adjusted, genotype-guided warfarin dosing refinement algorithm developed in Caribbean Hispanics showed better predictability (R2 = 0.70, MAE = 0.72mg/day than a clinical algorithm that excluded genotypes and admixture (R2 = 0.60, MAE = 0.99mg/day, and outperformed two prior pharmacogenetic algorithms in predicting effective dose in this population. For patients at the highest risk of adverse events, 45.5% of the dose predictions using the developed pharmacogenetic model resulted in ideal dose as compared with only 29% when using the clinical non-genetic algorithm (p<0.001. The admixture-driven pharmacogenetic algorithm predicted 58% of warfarin dose variance when externally validated in 55 individuals from an independent validation cohort (MAE = 0.89 mg/day, 24% mean bias.Results supported our rationale to incorporate individual's genotypes and unique admixture metrics into pharmacogenetic refinement models in order to increase predictability when expanding them to admixed populations like Caribbean Hispanics.ClinicalTrials.gov NCT01318057.

  2. Multiway admixture deconvolution using phased or unphased ancestral panels.

    Science.gov (United States)

    Churchhouse, Claire; Marchini, Jonathan

    2013-01-01

    We describe a novel method for inferring the local ancestry of admixed individuals from dense genome-wide single nucleotide polymorphism data. The method, called MULTIMIX, allows multiple source populations, models population linkage disequilibrium between markers and is applicable to datasets in which the sample and source populations are either phased or unphased. The model is based upon a hidden Markov model of switches in ancestry between consecutive windows of loci. We model the observed haplotypes within each window using a multivariate normal distribution with parameters estimated from the ancestral panels. We present three methods to fit the model-Markov chain Monte Carlo sampling, the Expectation Maximization algorithm, and a Classification Expectation Maximization algorithm. The performance of our method on individuals simulated to be admixed with European and West African ancestry shows it to be comparable to HAPMIX, the ancestry calls of the two methods agreeing at 99.26% of loci across the three parameter groups. In addition to it being faster than HAPMIX, it is also found to perform well over a range of extent of admixture in a simulation involving three ancestral populations. In an analysis of real data, we estimate the contribution of European, West African and Native American ancestry to each locus in the Mexican samples of HapMap, giving estimates of ancestral proportions that are consistent with those previously reported. PMID:23136122

  3. Influences of a New Admixture MX on Concrete Durability

    Institute of Scientific and Technical Information of China (English)

    MA Baoguo; DONG Rongzhen; ZHU Hongbo; ZHANG Li; ZHONG Kaihong; HE Xingyang; LI Zongjin

    2005-01-01

    The performance of concrete with a new admixture MX was studied by using the freeze-thaw cycle, permeability and chemical attack test. The experimental results show that MX improves the durability of concrete. Within the optimum proportion ranges from 0.1%to 1%,the compressive strength of concrete after freeze-thaw is increased by 20%-50%,and Young's modulus can be increased by 3.76-5.64 times.The strength and weight loss of concrete with 0.4%MX are respectively decreased by 28% and 60% after hydrochloric acid attack.The strength and weight loss of concrete with 0.4% MX are decreased by 5%-20% after sulfuric acid and sodium sulfate attack.The permeability of concrete with 1% MX at 28 days can be decreased by more than 30%. The investigation of the negative temperature property of MX and analysis on concrete composition and microstructure by MIP reveal that the heat conduction is resisted and the freezing procedure of solution in concrete pore is retarded due to the adding of MX. Moreover,the pore structure of concrete with MX is improved, thus improving the durability. Based on this study, a resistance model of MX to block the heat and mass transference was proposed, and the mechanism of durability improvement of concrete with MX was explained.

  4. A slide-rule for assessment of venous admixture.

    Science.gov (United States)

    Zetterström, H

    1989-04-01

    Determination of venous admixture (physiological shunt, Qva/Qt) requires analysis of both arterial and mixed venous blood. When a pulmonary arterial catheter is not in use, the pulmonary oxygenating capacity may be assessed from arterial blood gas data, the fraction of inspired oxygen (FIO2) and an assumed value of the arterial-mixed venous oxygen content difference. To facilitate this process, a slide-rule based on the "virtual shunt" concept is presented. It permits rapid assessment of Qva/Qt from known values of arterial oxygen tension (PaO2) or saturation (SaO2) and FIO2 and may promote the choice of appropriate FIO2. The limitations of the slide-rule were studied theoretically and its validity was tested by comparing 100 determinations of virtual shunt with the corresponding Qva/Qt values. The slide-rule was found to estimate Qva/Qt more accurately than commonly used oxygenation indices such as the PaO2/FIO2 ratio. PMID:2499154

  5. CFD Approaches for Modelling Bubble Entrainment by an Impinging Jet

    Directory of Open Access Journals (Sweden)

    Martin Schmidtke

    2009-01-01

    Full Text Available This contribution presents different approaches for the modeling of gas entrainment under water by a plunging jet. Since the generation of bubbles happens on a scale which is smaller than the bubbles, this process cannot be resolved in meso-scale simulations, which include the full length of the jet and its environment. This is why the gas entrainment has to be modeled in meso-scale simulations. In the frame of a Euler-Euler simulation, the local morphology of the phases has to be considered in the drag model. For example, the gas is a continuous phase above the water level but bubbly below the water level. Various drag models are tested and their influence on the gas void fraction below the water level is discussed. The algebraic interface area density (AIAD model applies a drag coefficient for bubbles and a different drag coefficient for the free surface. If the AIAD model is used for the simulation of impinging jets, the gas entrainment depends on the free parameters included in this model. The calculated gas entrainment can be adapted via these parameters. Therefore, an advanced AIAD approach could be used in future for the implementation of models (e.g., correlations for the gas entrainment.

  6. Resolving both entrainment-mixing and number of activated CCN in deep convective clouds

    Directory of Open Access Journals (Sweden)

    E. Freud

    2011-12-01

    Full Text Available The number concentration of activated CCN (Na is the most fundamental microphysical property of a convective cloud. It determines the rate of droplet growth with cloud depth and conversion into precipitation-sized particles and affects the radiative properties of the clouds. However, measuring Na is not always possible, even in the cores of the convective clouds, because entrainment of sub-saturated ambient air deeper into the cloud lowers the concentrations by dilution and may cause partial or total droplet evaporation, depending on whether the mixing is homogeneous or extreme inhomogeneous, respectively.

    Here we describe a methodology to derive Na based on the rate of cloud droplet effective radius (Re growth with cloud depth and with respect to the cloud mixing with the entrained ambient air. We use the slope of the tight linear relationship between the adiabatic liquid water mixing ratio and Re3 (or Rv3 to derive an upper limit for Na assuming extreme inhomogeneous mixing. Then we tune Na down to find the theoretical relative humidity that the entrained ambient air would have for each horizontal cloud penetration, in case of homogeneous mixing. This allows us to evaluate both the entrainment and mixing process in the vertical dimension in addition to getting a better estimation for Na.

    We found that the derived Na from the entire profile data is highly correlated with the independent CCN measurements from below cloud base. Moreover, it was found that mixing of sub-saturated ambient air into the cloud at scales of ~100 m and above is inclined towards the extreme inhomogeneous limit, i.e. that the time scale of droplet evaporation is significantly smaller than that for turbulent mixing. This means that ambient air that entrains

  7. Transport, Evolution and Entrainment of Asian Dust/Pollution into the Pacific Marine Boundary

    Science.gov (United States)

    Clarke, A. D.; McNaughton, C. S.; Kapustin, V.; Vetter, O.; Dibb, J. E.; Anderson, B. E.; Browell, E. V.; Carmichael, G.; Landing, B.

    2007-05-01

    Various airborne and ship based studies over the past several years have allowed us to measure Asian dust and pollution aerosol from near its source to locations up to 10,000km downwind where it was entrained into the marine boundary layer (MBL). Dust was found to accumulate up to half of the soluble species such as sulfate and nitrate during passage through pollution regions in Asia before being lofted into the free troposphere near Japan. At times, transport in the free troposphere included regions of subsidence in high pressure regions that brought these "rivers" of dust and pollution down to the top of the MBL. Shipboard measurements and lidar data indicated both clear air entrainment and convective activity, associated with the passage of low pressure systems, facilitated dust transport through the inversion. High temperature volatilization of particles in the MBL up to 900C was used to remove most sulfates, nitrates, carbon and sea-salt to leave only dust measured and sized by an optical particle counter. These shipboard data and concurrent chemical measurements revealed the relation between entrainment of pollution and dust into the MBL associated with passage of high pressure systems. Subsequent passage of low pressure systems also revealed scavenging and removal of aerosol through precipitation to the ocean surface. This process appears to be a common removal pathway for dust over the Pacific and a mechanism for supplying the ocean surface with soluble iron and aluminum to the ocean surface. Measurements in the free troposphere and MBL also captured various aspects of these processes. Airborne missions flown north of Hawaii during the NASA PEM-Tropics and IMPEX missions characterized the vertical structure of subsiding dust and pollution. In-flight mapping of the dust/pollution layers and structure using the NASA Langley DIAL LIDAR show a sloping, subsiding Asian air-mass entraining into the marine boundary layer (MBL). In-situ measurements of the aerosol

  8. Aeolian Induced Erosion and Particle Entrainment

    Science.gov (United States)

    Saint, Brandon

    2007-01-01

    The Granular Physics Department at The Kennedy Space Center is addressing the problem of erosion on the lunar surface. The early stages of research required an instrument that would produce erosion at a specific rate with a specific sample variation. This paper focuses on the development and experimental procedures to measure and record erosion rates. This was done with the construction of an open air wind tunnel, and examining the relationship between airflow and particle motion.

  9. Entrainment of ichthyoplankton and larval fishes during cooling water withdrawal

    International Nuclear Information System (INIS)

    Plantonic fish eggs and larvae are entrained into the Savannah River Plant (SRP) pumping system as Savannah River water is withdrawn for cooling purposes. The American shad contributed 96% of the planktonic fish eggs collected in the Savannah River. Eggs were rare in plankton samples from the intake canals and were assumed to have settled to the bottom as current velocity was reduced in the canal entrance. An estimated 72 million fish eggs were transported past the intake canals. Assuming ''worst case conditions,'' 6.8 million eggs (9.5%) could have been lost due to entrainment. Blueback herring comprised nearly one-half of the 216 million fish larvae susceptible to impact. Spotted sucker and black crappie were also common among the 22 species of fish larvae collected. An estimated 19.6 million (9.1%) fish larvae could have been entrained under ''worst case conditions''

  10. Optimal Asymptotic Entrainment of Phase-Reduced Oscillators

    CERN Document Server

    Zlotnik, Anatoly

    2011-01-01

    We derive optimal periodic controls for entrainment of a self-driven oscillator to a desired frequency. The alternative objectives of minimizing power and maximizing frequency range of entrainment are considered. A state space representation of the oscillator is reduced to a linearized phase model, and the optimal periodic control is computed from the phase response curve using formal averaging and the calculus of variations. Computational methods are used to calculate the periodic orbit and the phase response curve, and a numerical method for approximating the optimal controls is introduced. Our method is applied to asymptotically control the period of spiking neural oscillators modeled using the Hodgkin-Huxley equations. This example illustrates the optimality of entrainment controls derived using phase models when applied to the original state space system

  11. A model for droplet entrainment rate in horizontal stratified flow

    International Nuclear Information System (INIS)

    This work proposes an original approach for modeling the entrainment of droplets in a horizontal stratified two-phase wavy flows. This mechanistic model is based on the ripple-waves breakout and entrainment phenomenon by estimating the liquid mass pulled off the wave crests during their fragmentation. The paper presents the modeling procedure for estimating the wavelength of these ripples and the related entrained liquid volume. In regards to these parameters, it is shown that a relatively simple methodology can be obtained to ease the implementation in a system code. This work aims at substituting the current existing empirical correlations in the system code CATHARE 3 by using a flowfield for a liquid dispersed phase. (author)

  12. Entrainment into a stratocumulus layer with distributed radiative cooling

    Science.gov (United States)

    Randall, D. A.

    1980-01-01

    It is shown that the radiative cooling of a cloud layer strongly influences the turbulent flux profiles and the entrainment rate, and that the radiative cooling should be modeled as acting inside the turbulent layer. Numerical experiments demonstrate that a cloud-topped mixed-layer model, similar to that of Lilly (1968), is quite sensitive to delta (p) sub R, the depth of the radiatively cooled layer near cloud top. As delta (p) sub R increases, the model's sensitivity to the entrainment assumption is markedly heightened; for large delta (p) sub R the cloud top and cloud base rise as the entrainment parameter k is increased, while for small delta (p) sub R an increase in k has almost no effect. The model is most sensitive to delta (p) sub R for the cold-water, strong-divergence regime of greatest interest.

  13. Potent social synchronization can override photic entrainment of circadian rhythms.

    Science.gov (United States)

    Fuchikawa, Taro; Eban-Rothschild, Ada; Nagari, Moshe; Shemesh, Yair; Bloch, Guy

    2016-01-01

    Circadian rhythms in behaviour and physiology are important for animal health and survival. Studies with individually isolated animals in the laboratory have consistently emphasized the dominant role of light for the entrainment of circadian rhythms to relevant environmental cycles. Although in nature interactions with conspecifics are functionally significant, social signals are typically not considered important time-givers for the animal circadian clock. Our results challenge this view. By studying honeybees in an ecologically relevant context and using a massive data set, we demonstrate that social entrainment can be potent, may act without direct contact with other individuals and does not rely on gating the exposure to light. We show for the first time that social time cues stably entrain the clock, even in animals experiencing conflicting photic and social environmental cycles. These findings add to the growing appreciation for the importance of studying circadian rhythms in ecologically relevant contexts. PMID:27210069

  14. Direct numerical simulation of particle entrainment in turbulent channel flow

    International Nuclear Information System (INIS)

    Particle entrainment process in a turbulent channel flow is studied. The time history of the instantaneous turbulent velocity vector field is generated by the direct numerical simulation of the Navier--Stokes equation with the aid of a pseudospectral code. The equation of motion of submicrometer particles including Stokes drag and Brownian diffusion is used, and typical entrained particle trajectories are evaluated and statistically analyzed. It is shown that the wall coherent structure plays a dominant role on the particle entrainment process. Particles are removed from the wall region by being captured in the high speed streams moving away from the wall, which are formed by the flow structure. Furthermore, single streamwise vortices are shown to be more frequent than pairs of counter-rotating ones at every instance of time. Temporal average of the vorticity field, however, shows roughly periodic sequence of counter-rotating vortices in the wall region. copyright 1995 American Institute of Physics

  15. Extensive Admixture and Selective Pressure Across the Sahel Belt.

    Science.gov (United States)

    Triska, Petr; Soares, Pedro; Patin, Etienne; Fernandes, Veronica; Cerny, Viktor; Pereira, Luisa

    2015-12-01

    Genome-wide studies of African populations have the potential to reveal powerful insights into the evolution of our species, as these diverse populations have been exposed to intense selective pressures imposed by infectious diseases, diet, and environmental factors. Within Africa, the Sahel Belt extensively overlaps the geographical center of several endemic infections such as malaria, trypanosomiasis, meningitis, and hemorrhagic fevers. We screened 2.5 million single nucleotide polymorphisms in 161 individuals from 13 Sahelian populations, which together with published data cover Western, Central, and Eastern Sahel, and include both nomadic and sedentary groups. We confirmed the role of this Belt as a main corridor for human migrations across the continent. Strong admixture was observed in both Central and Eastern Sahelian populations, with North Africans and Near Eastern/Arabians, respectively, but it was inexistent in Western Sahelian populations. Genome-wide local ancestry inference in admixed Sahelian populations revealed several candidate regions that were significantly enriched for non-autochthonous haplotypes, and many showed to be under positive selection. The DARC gene region in Arabs and Nubians was enriched for African ancestry, whereas the RAB3GAP1/LCT/MCM6 region in Oromo, the TAS2R gene family in Fulani, and the ALMS1/NAT8 in Turkana and Samburu were enriched for non-African ancestry. Signals of positive selection varied in terms of geographic amplitude. Some genomic regions were selected across the Belt, the most striking example being the malaria-related DARC gene. Others were Western-specific (oxytocin, calcium, and heart pathways), Eastern-specific (lipid pathways), or even population-restricted (TAS2R genes in Fulani, which may reflect sexual selection). PMID:26614524

  16. Spatial assessment of Argentinean genetic admixture with geographical information systems.

    Science.gov (United States)

    Diaz-Lacava, Amalia; Walier, Maja; Penacino, Gustavo; Wienker, Thomas F; Baur, Max P

    2011-08-01

    In recent years there has been much attention to Argentinean population stratification. We were interested in assessing population stratification from a geographical perspective and summarizing it in form of maps. We mapped the genetic admixture of the extant male population in central and northern Argentina on the basis of forensic Y-chromosomal haplotypes. We addressed the question which group of genetically similar individuals is predominant in this area. Haplotypes containing seven Y-chromosomal short tandem repeat polymorphisms (Y-STRs), also known as microsatellites - DYS19, DYS389I, DYS389II, DYS390, DYS391, DYS392, DYS393 - were constructed for 145 individuals, recruited in 10 provinces. 97 distinct haplotypes were clustered into four clusters according to molecular distances. A genetic geostatistical analysis was conducted with the open-source geographical information system GRASS GIS. For each haplotype cluster, the according frequency was spatially interpolated over the total study area. Juxtaposing the interpolation surfaces, we screened point-wisely the maximal frequency as well as the label of the respective cluster. The screening results were combined in one summary map. We repeated this procedure for the second maximal frequencies. The resulting maps subdivide the study area into continuous regions comprising one predominant group of similar haplotypes. The first summary map divides the study area into three regions and the second summary map divides the area into four regions. The results of our analysis indicate that two groups of similar European haplotypes alternatively dominate the largest extension of the Argentinean territory. A third group, including South-American haplotypes, dominates the indigenous northwestern Argentinean area. The last group, including worldwide dispersed haplotypes, preponderates in frequency in second place in central Argentina. Our findings confirm a widespread European paternal ancestry, a substantial Amerindian

  17. Stability of total nutrient admixtures in a dual-chamber flexible container.

    Science.gov (United States)

    Tripp, M G; Menon, S K; Mikrut, B A

    1990-11-01

    The stability of total nutrient admixtures (TNAs) prepared from dextrose and amino acid injections commercially packaged in a dual-chamber container and a safflower-soybean oil fat emulsion was studied. The admixtures studied were divided into two groups. Group 1 admixtures represented 14 combinations of Aminosyn II, dextrose, and Liposyn II. Group 2 admixtures represented 10 combinations of Aminosyn II with Electrolytes, dextrose, and Liposyn II. Amino acid concentrations of 7, 8.5, and 10%, dextrose concentrations of 10, 20, 40, and 50%, and 10 and 20% fat emulsion were used. After the amino acid and dextrose injections were mixed in their original container (Nutrimix, Abbott Laboratories), the fat emulsion was added. One of two combinations of electrolytes and trace metals was then added. Multivitamins were added to each TNA just before 24-hour storage at room temperature (25 +/- 4 degrees C). Admixtures were tested initially and at the conclusion of storage periods of 24 hours at room temperature or nine days at 5 degrees C followed by 24 hours at room temperature. Measurements of pH, emulsion particle size, and weight percent of oil particles larger than 5 microns in diameter (HIAC) were made after visual inspection of each admixture. In selected admixtures, concentrations of individual amino acids and dextrose were determined by chromatographic techniques initially and at the conclusion of storage. The TNAs retained a uniform milk-like appearance throughout both storage periods. The pH values, particle size, HIAC measurements, and amino acid and dextrose concentrations remained essentially unchanged.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:2126163

  18. Entrainment of noise-induced and limit cycle oscillators under weak noise

    DEFF Research Database (Denmark)

    Mitarai, Namiko; Alon, Uri; Jensen, Mogens H

    2013-01-01

    can show only one-to-one entrainment to the external frequency, in contrast to the limit cycle oscillator which is known to entrain to any ratio. When the external forcing is multiplicative, on the other hand, the noise-induced oscillator can show entrainment to a few ratios other than one......-to-one, while the limit cycle oscillator shows entrain to any ratio. The noise blurs the entrainment in general, but clear entrainment regions for limit cycles can be identified as long as the noise is not too strong....

  19. Mixing and entrainment in hydraulically driven stratified sill flows

    DEFF Research Database (Denmark)

    Nielsen, Morten Holtegaard; Pratt, Larry; Helfrich, Karl

    2004-01-01

    The investigation involves the hydraulic behaviour of a dense layer of fluid flowing over an obstacle and subject to entrainment of mass and momentum from a dynamically inactive (but possibly moving) overlying fluid. An approach based on the use of reduced gravity, shallow-water theory with a cross......-interface entrainment velocity is compared with numerical simulations based on a model with continuously varying stratification and velocity. The locations of critical flow (hydraulic control) in the continuous model are estimated by observing the direction of propagation of small-amplitude long-wave disturbances...

  20. Side-entrainment in a jet embedded in a sidewind

    CERN Document Server

    Lopez-Camara, D

    2010-01-01

    Numerical simulations of HH jets never show side-entrainment of environmental material into the jet beam. This is because the bow shock associated with the jet head pushes the surrounding environment into a dense shell, which is never in direct contact with the sides of the jet beam. We present 3D simulations in which a side-streaming motion (representing the motion of the outflow source through the surrounding medium) pushes the post-bow shock shell into direct contact with the jet beam. This is a possible mechanism for modelling well collimated "molecular jets" as an atomic/ionic flow which entrains molecules initially present only in the surrounding environment.

  1. Gas entrainment indused by vortex behind an obstacle

    International Nuclear Information System (INIS)

    In this paper gas entrainment by vortex is studied, which can occur in coolant flow of FBR demonstration reactor. In this case the effect of horizontal flow and complicated boundary in it becomes very important. Therefore we performed fundamental experiments using water flow with cylindrical obstacle. The experimental results show that the relative locations of obstacle and outlet affects the pattern of flow and gas entrainment, which is categorized into four cases. A two-dimensional numerical analysis is also performed to investigate the flow pattern, where the outlet is taken into account. (author)

  2. Entrained liquid fraction prediction in adiabatic and evaporating annular two-phase flow

    International Nuclear Information System (INIS)

    Highlights: ► New method to predict the entrained liquid fraction in annular two-phase flow. ► Circular and non-circular tubes, adiabatic and evaporating conditions covered. ► Large underlying experimental database (2460 points). ► New method explicit and fully stand-alone. ► New method based on just 1 dimensionless group: the core flow Weber number. - Abstract: A new method to predict the entrained liquid fraction in annular two-phase flow is presented. The underlying experimental database contains 2460 data points collected from 38 different literature studies for 8 different gas–liquid or vapor–liquid combinations (R12, R113, water–steam, water–air, genklene–air, ethanol–air, water–helium, silicon–air), tube diameters from 5.0 mm to 95.3 mm, pressures from 0.1 to 20.0 MPa and covers both adiabatic and evaporating flow conditions, circular and non-circular channels and vertical upflow, vertical downflow and horizontal flow conditions. Annular flows are regarded here as a special form of a liquid atomization process, where a high velocity confined spray, composed by the gas phase and entrained liquid droplets, flows in the center of the channel dragging and atomizing the annular liquid film that streams along the channel wall. Correspondingly, the liquid film flow is assumed to be shear-driven and the energy required to drive the liquid atomization is assumed to be provided in the form of kinetic energy of the droplet-laden gas core flow, so that the liquid film–gas core aerodynamic interaction is ultimately assumed to control the liquid disintegration process. As such, the new prediction method is based on the core flow Weber number, representing the ratio of the disrupting aerodynamic force to the surface tension retaining force, a single and physically plausible dimensionless group. The new prediction method is explicit, fully stand-alone and reproduces the available data better than existing empirical correlations, including in

  3. Entrainment of radio frequency chaff by wind as a function of surface aerodynamic roughness.

    Science.gov (United States)

    Gillies, John A; Nickling, William G

    2003-02-01

    Radio frequency (RF) chaff (approximately 2-cm x 25-microm diameter aluminum-coated glass silicate cylinders) released by military aircraft during testing and training activities has the potential to become entrained by wind upon settling to the Earth's surface. Once entrained from the surface there is the potential for RF chaff to be abraded and produce PM10 and PM2.5, which are regulated pollutants and pose health concerns. A series of portable wind tunnel tests were carried out to examine the propensity of RF chaff to become entrained by wind by defining the relationship between the threshold friction velocity of RF chaff (u(*t RF chaff)) and aerodynamic roughness (z(o)) of surfaces onto which it may deposit. The test surfaces were of varying roughness including types near the Naval Air Station (NAS), Fallon, NV, where RF chaff is released. The u(*t) of this fibrous material ranged from 0.14 m/sec for a smooth playa to 0.82 m/sec for a rough crusted playa surface with larger cobble-sized (approximately 6-26-cm diameter) rocks rising above the surface. The u(*t RF chaff) is dependent on the z(o) of the surface onto which it falls as well as the physical characteristics of the roughness. The wind regime of Fallon would allow for chaff suspension events to occur should it settle on typical surfaces in the area. However, the wind climatology of this area makes the probability of such events relatively low. PMID:12617294

  4. ADSORPTION OF CHROMIUM (VI FROM AQUEOUS SOLUTIONS BY DIFFERENT ADMIXTURES – A BATCH EQUILIBRIUM TEST STUDY

    Directory of Open Access Journals (Sweden)

    K. SHIVA PRASHANTH KUMAR

    2014-08-01

    Full Text Available Wide variety of inorganic compounds such as nutrients and trace metals, organic chemicals, radioactive contaminants and pathogens are commonly present as contaminants in the groundwater. Migration of contaminants in soil involves important mechanisms such as molecular diffusion, dispersion under physical processes, adsorption, precipitation and oxidation - reduction under chemical processes and biodegradation under biological process. Cr (VI is a major and dangerous contaminant as per the ground water is concerned. There are numerous research work carried out with concentrated efforts by the researchers towards removal of Cr (VI contaminant from aqueous solutions. There are few studies relevant to Cr (VI removal with respect to utilization of low cost admixtures and also soil type. In the present study, different low cost admixtures like rice husk (RH, shredded tyre (ST and fly ash (FA are used to understand the performance in removal of Cr (VI from aqueous solution and also two different soil types are used along with the admixture. The results are discussed in terms of sorption capacity and performance of individual admixture and combination of admixture with soil in removal of contaminant. The fly ash, rice husk and shredded tyre admixtures are used and the results revealed that the shredded tyre showed higher performance in removal of contaminant concentration. Also, the soil which has more fine particle content (size<0.075 mm IS sieve showed reasonable reduction in concentration of contaminant at the lower levels of contaminant initial concentration. The sorption capacity results of Cr (VI contaminant, treated with various admixtures are further validated with the published work of other investigators. The shredded tyre (ST showed more adsorption capacity, i.e., 3.283 mg/g at pH of 4.8. For other admixtures, adsorption capacity value is varying in the range of 0.07 mg/g to 1.7 mg/g. Only in case of activated alumina and modified saw dust

  5. The Mechanism of the Eeffect of Mineral Admixtures on the Expansion of Aalkali-silica Reaction

    Institute of Scientific and Technical Information of China (English)

    WANG Aiqin; Niu Jishou; ZHANG Chengzhi

    2008-01-01

    On the base of the influence rule of silica fume, slag and fly ash on alkali-silica reaction under the condition of 70℃, the mechanism of the effect of mineral admixtures on alkali-silica reaction is studied further in the paper. The results show that the effects of mineral admixtures on alkali-silica reaction are mainly chemistry effect and surface physichemistry effect. Under suitable condition, the chemistry effect may make alkali-silica reaction to be inhibited effectively, but the physichemistry effect only make alkali-silica reaction to be delayed. The chemistry effect and the physichemistry effect of minerals admixture are relative to the content of Ca(OH)2 in system. Under the condition that there is a large quantity of Ca(OH)2, mineral admixture cannot inhibit alkali-silica reaction effectively. Only when Ca(OH)2 in the system is very less, it is possible that mineral admixture inhibits alkali-silica reaction effectively.

  6. Efficacy of Industrial waste admixture in Improving Engineering Performance of Clayey soil – A quantitative study

    Directory of Open Access Journals (Sweden)

    Kiran B. Biradar

    2014-09-01

    Full Text Available Infrastructure and industrialization serves as a back bone for a country’s economy. However due to rapid industrialization there exist a problem in the form of waste accumulation and subsequent problems due to their disposal & effects of waste. In infrastructure development, roads play a major role. In general pavement construction needs bulk quantities of good soil keeping in view of the service and longevity aspects. Due to limitation in availability of good soil, often the cost of projects escalates. An ideal solution lies for reducing project cost, increasing longevity and reduce accumulation of waste shall be through utilization of industrial waste combined with weak soil for pavement construction. Few types of waste materials namely crusher dust, fly ash and Steel slag waste are popular as admixtures in improving weak soils. This paper discusses the performance of admixtures in improving weak soil through mechanical stabilization. Results of tests on index and engineering properties of mechanically stabilized clayey soil with industrial waste admixtures namely, crusher dust, fly ash and steel slag are presented for different admixture contents and test conditions. A comparison is made based on improved performance. It is observed that Steel slag is proven to be effective over other types. From the results optimum content of admixture for a given improvement is suggested.

  7. Effect of Gum Arabic karroo as a Water-Reducing Admixture in Concrete

    Directory of Open Access Journals (Sweden)

    Rose Mbugua

    2016-01-01

    Full Text Available Concrete is one of the most popular construction materials in the world. Chemical admixtures are ingredients added to concrete to enhance its properties. However, most chemical admixtures on the market today are expensive, thereby making them out of reach for small consumers of concrete. In Africa, use of chemical admixtures is rare despite the harsh weather conditions. In the current study, Gum from Acacia karroo (GAK was used as a water-reducing admixture in concrete. A slump test, density and compressive strength were studied using different dosages of GAK while neat concrete was the control. Results showed that slump increased by 200% at a 2% dosage of GAK. This enabled reduction of water-to-binder (w/b ratio from 0.61 to 0.48 for samples with a 3% dosage. Reduction in w/b resulted in increased compressive strength of 37.03% above the control after 180 days of curing for a 3% dosage. XRD studies also showed a decreased rate of hydration in the presence of GAK in concrete. It was concluded that GAK can be used in concrete as a water-reducing admixture, which is environmentally-friendly, thus producing sustainable and greener concrete.

  8. Mechanical characteristics of hardened concrete with different mineral admixtures: a review.

    Science.gov (United States)

    Ayub, Tehmina; Khan, Sadaqat Ullah; Memon, Fareed Ahmed

    2014-01-01

    The available literature identifies that the addition of mineral admixture as partial replacement of cement improves the microstructure of the concrete (i.e., porosity and pore size distribution) as well as increasing the mechanical characteristics such as drying shrinkage and creep, compressive strength, tensile strength, flexural strength, and modulus of elasticity; however, no single document is available in which review and comparison of the influence of the addition of these mineral admixtures on the mechanical characteristics of the hardened pozzolanic concretes are presented. In this paper, based on the reported results in the literature, mechanical characteristics of hardened concrete partially containing mineral admixtures including fly ash (FA), silica fume (SF), ground granulated blast furnace slag (GGBS), metakaolin (MK), and rice husk ash (RHA) are discussed and it is concluded that the content and particle size of mineral admixture are the parameters which significantly influence the mechanical properties of concrete. All mineral admixtures enhance the mechanical properties of concrete except FA and GGBS which do not show a significant effect on the strength of concrete at 28 days; however, gain in strength at later ages is considerable. Moreover, the comparison of the mechanical characteristics of different pozzolanic concretes suggests that RHA and SF are competitive. PMID:24688443

  9. Regional admixture mapping and structured association testing: conceptual unification and an extensible general linear model.

    Directory of Open Access Journals (Sweden)

    David T Redden

    2006-08-01

    Full Text Available Individual genetic admixture estimates, determined both across the genome and at specific genomic regions, have been proposed for use in identifying specific genomic regions harboring loci influencing phenotypes in regional admixture mapping (RAM. Estimates of individual ancestry can be used in structured association tests (SAT to reduce confounding induced by various forms of population substructure. Although presented as two distinct approaches, we provide a conceptual framework in which both RAM and SAT are special cases of a more general linear model. We clarify which variables are sufficient to condition upon in order to prevent spurious associations and also provide a simple closed form "semiparametric" method of evaluating the reliability of individual admixture estimates. An estimate of the reliability of individual admixture estimates is required to make an inherent errors-in-variables problem tractable. Casting RAM and SAT methods as a general linear model offers enormous flexibility enabling application to a rich set of phenotypes, populations, covariates, and situations, including interaction terms and multilocus models. This approach should allow far wider use of RAM and SAT, often using standard software, in addressing admixture as either a confounder of association studies or a tool for finding loci influencing complex phenotypes in species as diverse as plants, humans, and nonhuman animals.

  10. Queueing-Based Synchronization and Entrainment for Synthetic Gene Oscillators

    Science.gov (United States)

    Mather, William; Butzin, Nicholas; Hochendoner, Philip; Ogle, Curtis

    Synthetic gene oscillators have been a major focus of synthetic biology research since the beginning of the field 15 years ago. They have proven to be useful both for biotechnological applications as well as a testing ground to significantly develop our understanding of the design principles behind synthetic and native gene oscillators. In particular, the principles governing synchronization and entrainment of biological oscillators have been explored using a synthetic biology approach. Our work combines experimental and theoretical approaches to specifically investigate how a bottleneck for protein degradation, which is present in most if not all existing synthetic oscillators, can be leveraged to robustly synchronize and entrain biological oscillators. We use both the terminology and mathematical tools of queueing theory to intuitively explain the role of this bottleneck in both synchronization and entrainment, which extends prior work demonstrating the usefulness of queueing theory in synthetic and native gene circuits. We conclude with an investigation of how synchronization and entrainment may be sensitive to the presence of multiple proteolytic pathways in a cell that couple weakly through crosstalk. This work was supported by NSF Grant #1330180.

  11. Characterization of Residual Particulates from Biomass Entrained Flow Gasification

    DEFF Research Database (Denmark)

    Qin, Ke; Lin, Weigang; Fæster, Søren;

    2013-01-01

    Biomass gasification experiments were carried out in a bench scale entrained flow reactor, and the produced solid particles were collected by a cyclone and a metal filter for subsequent characterization. During wood gasification, the major part of the solid material collected in the filter is soot...

  12. Measured gas and particle temperatures in VTT's entrained flow reactor

    DEFF Research Database (Denmark)

    Clausen, Sønnik; Sørensen, L.H.

    2006-01-01

    Particle and gas temperature measurements were carried out in experiments on VTTs entrained flow reactor with 5% and 10% oxygen using Fourier transform infrared emission spectroscopy (FTIR). Particle temperature measurements were performed on polish coal,bark, wood, straw particles, and bark and...

  13. Development and entrainment of the colonic circadian clock during ontogenesis

    Czech Academy of Sciences Publication Activity Database

    Polidarová, Lenka; Olejníková, Lucie; Paušlyová, Lucia; Sládek, Martin; Soták, Matúš; Pácha, Jiří; Sumová, Alena

    2014-01-01

    Roč. 306, č. 4 (2014), G346-G356. ISSN 0193-1857 R&D Projects: GA ČR(CZ) GAP303/12/1108 Institutional support: RVO:67985823 Keywords : circadian clock * clock gene * ontogenesis * circadian entrainment Subject RIV: ED - Physiology Impact factor: 3.798, year: 2014

  14. EFFECTS OF CONTINUOUS CHLORINATION ON ENTRAINED ESTUARINE PLANKTON

    Science.gov (United States)

    The effects of continuous chlorination on entrained plankton are investigated in tests using running sea water and adenosine triphosphate (ATP) as an indicator of biomass. Effects were measured by bioluminescence with the use of luciferin-luciferase reagents from firefly lanterns...

  15. Historical development of entrainment models for Hudson River striped bass

    International Nuclear Information System (INIS)

    In the mid-1960s, concerns surfaced regarding entrainment and impingement of young-of-the-year (age-0) striped bass by electric power generating facilities on the Hudson River. These concerns stimulated the development of increasingly complex models to evaluate the impacts of these facilities. The earliest simplistic formulas, based on empirical data, proved inadequate because of conceptual shortcomings, incomplete development, and lack of data. By 1972, complex transport models based on biological and hydrodynamic principles had been developed and applied by scientists representing both the utilities and the government. Disagreements about the acceptability of these models spurred the development of even more complex models. The entrainment models stimulated the collection of substantial amounts of field data to define the spatial distributions and entrainment survival of early life stages. As the difficulties of accounting for the movement of early life stages from hydrodynamic principles became more evident and as more field data became available, simpler empirical modeling approaches became both practical and defensible. Both empirical and hydrodynamic modeling approaches were applied during the US Environmental Protection Agency's hearings on the Hudson River power case (1977-1980). The main lessons learned from the experience with entrainment-impingement modeling are that complex mechanistic models are not necessarily better than simpler empirical models for young fish, and that care must be taken to construct even the simple models correctly. 29 refs., 4 figs., 1 tab

  16. Efficiency of brainwave entrainment by binaural beats in reducing anxiety

    Directory of Open Access Journals (Sweden)

    Ahmad Alipoor

    2014-04-01

    Full Text Available Background: Anxiety is a fundamental phenomenon that is a common symptom in all mental disorders. The aim of the present study was to assess the effect of brainwave entrainment on anxiety reduction using binaural beats. Methods: In this experimental double-blind study, 30 employees were selected from an engineering research firm through random sampling and replacement and divided into two groups: control group and experimental group. All participants completed the Spielberger’s State-Trait Anxiety Inventory (STAI. Then, the experimental group listened to binaural beats which was recorded on a non-vocal piece of music for 4 weeks, 3 sessions each week. Each session lasted about 20 minutes. At the same time, the control group listened to the background music without any entrainment sound. At the end, both groups completed the anxiety questionnaire and the anxiety scores of both groups obtained before and after intervention were analyzed by ANCOVA. Results: The findings showed that the brainwave entrainment using binaural beats led to the significant reduction of state anxiety (P<0.001 and trait anxiety (P<0.018. Conclusion: Brainwave entrainment using binaural beats is an effective factor in decreasing state and trait anxiety; so, it can be used to reduce anxiety in mental health centers.

  17. A viscous-inviscid interaction model of jet entrainment

    Science.gov (United States)

    Wilmoth, R. G.; Dash, S. M.

    1981-01-01

    A viscous-inviscid interaction model for predicting jet entrainment effects on axisymmetric, nozzle afterbodies at subsonic speeds is presented. The model is based on a displacement thickness correction to the inviscid jet boundary that accounts for mixing-induced streamline deflections in the inviscid region. The displacement correction is shown to be related to the local mass entrainment rate and, for thin mixing layers, the model is shown to be analogous to displacement models used in conventional boundary-layer interaction theory. A method is presented for computing the entrainment rate by an overlaid mixing layer model that accounts for the nonsimilar behavior and pressure gradients occurring in the near field region. An iterative scheme for coupling the model to analyses for the external inviscid flow, the external boundary layer, and the inviscid jet exhaust is also given. Results are presented that illustrate the qualitative behavior of the entrainment interaction under various flow conditions and that demonstrate the validity of the model by comparisons with experiment.

  18. Lexical Entrainment and Lexical Differentiation in Reference Phrase Choice

    Science.gov (United States)

    Van Der Wege, Mija M.

    2009-01-01

    Speakers reuse prior references to objects when choosing reference phrases, a phenomenon known as lexical entrainment. One explanation is that speakers want to maintain a set of previously established referential precedents. Speakers may also contrast any new referents against this previously established set, thereby avoiding applying the same…

  19. Research on bubble entraining accompanying shearing vortex flow between structures

    International Nuclear Information System (INIS)

    The top entry type loop reactor, on which the preparatory research of the conceptual design has been advanced as the demonstration reactor of FBRs, is the multiple liquid surface system which has independent free liquid surfaces in the reactor vessel and the intermediate heat exchanger vessel. As one of the problems due to the boundaries with complex shapes, there is the entraining of gas at free liquid surface, and that due to swirling vortices is dominant. In this research, by the experiment using the system in which a simple obstacle and a suction port in its wake are arranged, the phenomena of the swirling vortices generated by sucked downflow, the entraining of gas and others in lateral flow, and the dependence of those on various parameters were investigated. Further, the state of forming vortices changing by the relative positions of the obstacle and the downflow was analyzed by using a numerical analysis code for two-dimensional system, and the relation of the flow pattern and the entraining of gas was examined. The experimental setup, visualizing measurement method, the experimental conditions, the experimental results, flow turbulence and gas entraining, and the method of numerical analysis and the results are reported. (K.I.)

  20. Genetic admixture and lineage separation in a southern Andean plant

    Science.gov (United States)

    Morello, Santiago; Sede, Silvana M.

    2016-01-01

    varieties of E. alpina: var. alpina is more closely related to E. rubra and other species than to its own counterpart E. alpina var. carmelitana. Geometric morphometrics analysis (Elliptic Fourier descriptors) revealed significant differences in leaf shape between varieties. We found that diversity in Escallonia species analyzed here is geographically structured and deep divergence between varieties of E. alpina could be associated to ancient evolutionary events like orogeny. Admixture in southern populations could be the result of hybridization at the margins of the parental species’ distribution range. PMID:27179539

  1. Gas entrainment rate coefficient of an ideal momentum atomizing liquid jet

    CERN Document Server

    Medrano, Fermín Franco; Velte, Clara Marika; Hodžić, Azur

    2016-01-01

    We propose a two-phase-fluid model for a turbulent full-cone high speed atomizing liquid jet that describes its dynamics in a simple but comprehensive manner with only the apex angle of the cone being a disposable parameter. The basic assumptions are that (i) the jet is statistically stationary and that (ii) it can be approximated by a mixture of a liquid and a gas with its phases in dynamic equilibrium. To derive the model, we impose conservation of the liquid volume and total momentum fluxes. Our model equation admits analytical solutions for the composite density and velocity of the two-phase fluid, both as functions of the distance from the nozzle, from which the dynamic pressure and gas the entrainment rate coefficient are calculated. Assuming a far-field approximation, we theoretically derive a constant gas entrainment rate coefficient solely in terms of the cone angle. Moreover, we carry out experiments for a single-phase turbulent air jet and show that the predictions of our model compare well with th...

  2. Airborne observation of mixing across the entrainment zone during PARADE 2011

    Science.gov (United States)

    Berkes, Florian; Hoor, Peter; Bozem, Heiko; Kunkel, Daniel; Sprenger, Michael; Henne, Stephan

    2016-05-01

    This study presents the analysis of the structure and air mass characteristics of the lower atmosphere during the field campaign PARADE (PArticles and RAdicals: Diel observations of the impact of urban and biogenic Emissions) on Mount Kleiner Feldberg in southwestern Germany during late summer 2011. We analysed measurements of meteorological variables (temperature, moisture, pressure, wind speed and direction) from radio soundings and of chemical tracers (carbon dioxide, ozone) from aircraft measurements. We focus on the thermodynamic and dynamic properties that control the chemical distribution of atmospheric constituents in the boundary layer. We show that the evolution of tracer profiles of CO2 and O3 indicate mixing across the inversion layer (or entrainment zone). This finding is supported by the analysis of tracer-tracer correlations which are indicative for mixing and the relation of tracer profiles in relation to the evolution of the boundary layer height deduced from radio soundings. The study shows the relevance of entrainment processes for the lower troposphere in general and specifically that the tracer-tracer correlation method can be used to identify mixing and irreversible exchange processes across the inversion layer.

  3. Effect of Functional Chemical Admixtures on the Performance of Cement Asphalt Mortar Used in Ballastless Track

    Institute of Scientific and Technical Information of China (English)

    JIANG Jinyang; SHE Wei; LI Wei; PAN Li

    2015-01-01

    Chemical admixtures are of paramount importance to the performance of modern cement based composites. In this paper, we performed a series of tests to investigate the effects of chemical admixtures on the cement asphalt mortar (CA mortar), i e, compressive strength, frost resistance, permeability, fatigue resistance, pore structure and microstructure. In particular, two types of chemical admixtures were tested,i e, defoamer (tributyl phosphate (TBP)) and polycarboxylate superplasticizer (PS). The results indicate that the addition of TBP and PS eliminates big bubbles and promotes small non-connected pores forming in matrix. Besides, an optimum dosage of TBP and PS may be determined with respect to the frost resistance, permeability and fatigue resistance of CA mortar. Further elaborative discussions are presented as well as experimental evidences from mercury intrusion porosimetry, scanning electron microscopy and energy dispersive spectroscopy.

  4. Assessment of ichthyoplankton entrainment at Pickering 'A' NGS using a pump/net in lake system

    International Nuclear Information System (INIS)

    Annual entrainment at Pickering 'A' NGS was estimated for alewife as 13.6 X 106 larvae and 409 X 106 eggs. A substantial portion of eggs and larvae entering the intake were dead due to natural mortality (41%-81%) prior to entrainment. Viable eggs and larvae, immediately following entrainment showed mortalities of 54% and 44% respectively. The latent mortality of entrained eggs was 100% (48 h)

  5. Direct simulation of turbulent entrainment due to a plume impinging on a density interface

    International Nuclear Information System (INIS)

    The law for turbulent entrainment due to plumes and jets impinging on a density interface is subject to significant uncertainty, with reported differences in entrainment rates up to a factor of 10. We report preliminary results obtained by Direct Numerical Simulation which are part of a PRACE project on turbulent entrainment carried out on JUGENE at Jülich, Germany. Various interface tracking methods are discussed and the entrainment coefficient is determined.

  6. African and non-African admixture components in African Americans and an African Caribbean population.

    Science.gov (United States)

    Murray, Tanda; Beaty, Terri H; Mathias, Rasika A; Rafaels, Nicholas; Grant, Audrey Virginia; Faruque, Mezbah U; Watson, Harold R; Ruczinski, Ingo; Dunston, Georgia M; Barnes, Kathleen C

    2010-09-01

    Admixture is a potential source of confounding in genetic association studies, so it becomes important to detect and estimate admixture in a sample of unrelated individuals. Populations of African descent in the US and the Caribbean share similar historical backgrounds but the distributions of African admixture may differ. We selected 416 ancestry informative markers (AIMs) to estimate and compare admixture proportions using STRUCTURE in 906 unrelated African Americans (AAs) and 294 Barbadians (ACs) from a study of asthma. This analysis showed AAs on average were 72.5% African, 19.6% European and 8% Asian, while ACs were 77.4% African, 15.9% European, and 6.7% Asian which were significantly different. A principal components analysis based on these AIMs yielded one primary eigenvector that explained 54.04% of the variation and captured a gradient from West African to European admixture. This principal component was highly correlated with African vs. European ancestry as estimated by STRUCTURE (r(2)=0.992, r(2)=0.912, respectively). To investigate other African contributions to African American and Barbadian admixture, we performed PCA on approximately 14,000 (14k) genome-wide SNPs in AAs, ACs, Yorubans, Luhya and Maasai African groups, and estimated genetic distances (F(ST)). We found AAs and ACs were closest genetically (F(ST)=0.008), and both were closer to the Yorubans than the other East African populations. In our sample of individuals of African descent, approximately 400 well-defined AIMs were just as good for detecting substructure as approximately 14,000 random SNPs drawn from a genome-wide panel of markers. PMID:20717976

  7. Estimated Entrainment of Dungeness Crab During Dredging For The Columbia River Channel Improvement Project

    Energy Technology Data Exchange (ETDEWEB)

    Pearson, Walter H.; Williams, Greg D.; Skalski, John R.

    2002-12-01

    The studies reported here focus on issues regarding the entrainment of Dungeness crab related to the proposed Columbia River Channel Improvement Project and provided direct measurements of crab entrainment rates at three locations (Desdomona Shoals, Upper Sands, and Miller Sands) from RM4 to RM24 during summer 2002. Entrainment rates for all age classes of crabs ranged from zero at Miller Sands to 0.224 crabs per cy at Desdemona Shoals in June 2002. The overall entrainment rate at Desdomona Shoals in September was 0.120 crabs per cy. A modified Dredge Impact Model (DIM) used the summer 2002 entrainment rates to project crab entrainment and adult equivalent loss and loss to the fishery for the Channel Improvement Project. To improve the projections, entrainment data from Flavel Bar is needed. The literature, analyses of salinity intrusion scenarios, and the summer 2002 site-specific data on entrainment and salinity all indicate that bottom salinity influences crab distribution and entrainment, especially at lower salinities. It is now clear from field measurements of entrainment rates and salinity during a period of low river flow (90-150 Kcfs) and high salinity intrusion that entrainment rates are zero where bottom salinity is less than 16 o/oo most of the time. Further, entrainment rates of 2+ and older crab fall with decreasing salinity in a clear and consistent manner. More elaboration of the crab distribution- salinity model, especially concerning salinity and the movements of 1+ crab, is needed.

  8. Y-STR diversity and ethnic admixture in White and Mulatto Brazilian population samples

    OpenAIRE

    Luzitano Brandão Ferreira; Celso Teixeira Mendes-Junior; Cláudia Emília Vieira Wiezel; Marcelo Rizzatti Luizon; Aguinaldo Luiz Simões

    2006-01-01

    We investigated 50 Mulatto and 120 White Brazilians for the Y-chromosome short tandem repeat (Y-STR) markers (DYS19, DYS390, DYS391, DYS392 and DYS393) and found 79 different haplotypes in the White and 35 in the Mulatto sample. Admixture estimates based on allele frequencies showed that the admixture of the white sample was 89% European, 6% African and 5% Amerindian while the Mulatto sample was 93% European and 7% African. Results were consistent with historical records of the directional ma...

  9. Y-STR diversity and ethnic admixture in White and Mulatto Brazilian population samples

    Directory of Open Access Journals (Sweden)

    Luzitano Brandão Ferreira

    2006-01-01

    Full Text Available We investigated 50 Mulatto and 120 White Brazilians for the Y-chromosome short tandem repeat (Y-STR markers (DYS19, DYS390, DYS391, DYS392 and DYS393 and found 79 different haplotypes in the White and 35 in the Mulatto sample. Admixture estimates based on allele frequencies showed that the admixture of the white sample was 89% European, 6% African and 5% Amerindian while the Mulatto sample was 93% European and 7% African. Results were consistent with historical records of the directional mating between European males and Amerindian or African females.

  10. Portland cement hydration in the presence of admixtures: black gram pulse and superplasticizer

    Directory of Open Access Journals (Sweden)

    Viveka Nand Dwivedi

    2008-12-01

    Full Text Available Effect of admixtures such as black gram pulse (BGP and sulfonated naphthalene based superplasticizer (SP on the hydration of Portland cement has been studied. The hydration characteristics of OPC in the presence of BGP and SP were studied with the help of non evaporable water content determinations, calorimetric method, Mössbauer spectroscopic and atomic force microscopic techniques. Results have shown that both BGP and SP get adsorbed at the surface of cement and its hydration products. The hydration of Portland cement is retarded in the presence of both the admixtures and nanosize hydration products are formed.

  11. Tensile strength of green concrete with fly ash and chemical admixtures

    Energy Technology Data Exchange (ETDEWEB)

    Ravina, D. [Technion-Israel Institute of Technology, Haifa (Israel). Faculty of Civil Engineering, National Building Research Institute

    1995-08-01

    The effect of Class F coal fly ash of marginal quality, as partial replacement for fine sand, and of chemical admixtures (water-reducing and retarding and high-rank water reducer) on the tensile strength of green concrete was investigated. The tests show that the fly ash significantly increased (by 25 to 40%) the tensile strength at 2 to 4 hours after mixing, compared with `similar` mixes without fly ash. On the other hand, the chemical admixtures with retarding properties significantly slowed down its growth over the first few hours. 4 refs., 7 figs., 6 tabs.

  12. Effects of drying conditions, admixtures and specimen size on shrinkage strains

    International Nuclear Information System (INIS)

    The paper presents the results of an experimental investigation on the effects of drying conditions, specimen size and presence of plasticizing admixture on the development of shrinkage strains. The measurements are taken in a harsh (50 deg. C and 5% R.H.) and a moderate environment (28 deg. C and 50% R.H.). The results include strain development at various levels of cross sections of concrete prisms. The drying conditions are found to be the dominant parameter affecting the shrinkage strain development particularly in specimens of smaller sizes. The effect of plasticizing admixture on shrinkage strains is negligible

  13. Further characterization of theobroma oil-beeswax admixtures as lipid matrices for improved drug delivery systems.

    Science.gov (United States)

    Attama, A A; Schicke, B C; Müller-Goymann, C C

    2006-11-01

    There is an increasing interest in lipid based drug delivery systems due to factors such as better characterization of lipidic excipients and formulation versatility and the choice of different drug delivery systems. It is important to know the thermal characteristics, crystal habit, texture, and appearance of a new lipid matrix when determining its suitability for use in certain pharmaceutical application. It is line with this that this research was embarked upon to characterize mixtures of beeswax and theobroma oil with a view to applying their admixtures in drug delivery systems such as solid lipid nanoparticles and nanostructured lipid carriers. Admixtures of theobroma oil and beeswax were prepared to contain 25% w/w, 50% w/w, and 75% w/w of theobroma oil. The admixtures were analyzed by differential scanning calorimetry (DSC), small angle X-ray diffraction (SAXD), wide angle X-ray diffraction (WAXD), and isothermal heat conduction microcalorimetry (IMC). The melting behavior and microstructures of the lipid admixtures were monitored by polarized light microscopy (PLM). Transmission electron microscopy (TEM) was used to study the internal structures of the lipid bases. DSC traces indicated that the higher melting peaks were roughly constant for the different admixtures, but lower melting peaks significantly increased (p beeswax in all the lipid matrix admixtures at all stages of the study. PLM micrographs revealed differences with regard to the thermal and optical behaviors depending on the composition of the matrix. The lipid matrix consisting of 75% w/w of theobroma oil showed a spherulite texture after 4 weeks of isothermal storage. Crystallization exotherms of lipid matrices containing 50% w/w and 25% w/w of theobroma oil showed change in modification after 30 min with the latter having a greater time-dependent crystallization. Generally, low non-integral Avrami exponents and growth rate constants were obtained for all the lipid matrices, with the admixture

  14. Thermal creep-assisted dust lifting on Mars: Wind tunnel experiments for the entrainment threshold velocity

    Science.gov (United States)

    Küpper, Markus; Wurm, Gerhard

    2015-07-01

    In this work we present laboratory measurements on the reduction of the threshold friction velocity necessary for lifting dust if the dust bed is illuminated. Insolation of a porous soil establishes a temperature gradient. At low ambient pressure this gradient leads to thermal creep gas flow within the soil. This flow leads to a subsurface overpressure which supports lift imposed by wind. The wind tunnel was run with Mojave Mars Simulant and air at 3, 6, and 9mbar, to cover most of the pressure range at Martian surface levels. Our first measurements imply that the insolation of the Martian surface can reduce the entrainment threshold velocity between 4% and 19% for the conditions sampled with our experiments. An insolation activated soil might therefore provide additional support for aeolian particle transport at low wind speeds.

  15. Thermal creep assisted dust lifting on Mars: Wind tunnel experiments for the entrainment threshold velocity

    CERN Document Server

    Küpper, Markus

    2015-01-01

    In this work we present laboratory measurements on the reduction of the threshold friction velocity necessary for lifting dust if the dust bed is illuminated. Insolation of a porous soil establishes a temperature gradient. At low ambient pressure this gradient leads to thermal creep gas flow within the soil. This flow leads to a sub-surface overpressure which supports lift imposed by wind. The wind tunnel was run with Mojave Mars Simulant and air at 3, 6 and 9 mbar, to cover most of the pressure range at martian surface levels. Our first measurements imply that the insolation of the martian surface can reduce the entrainment threshold velocity between 4 % and 19 % for the conditions sampled with our experiments. An insolation activated soil might therefore provide additional support for aeolian particle transport at low wind speeds.

  16. Isospin dependence of entrainment in superfluid neutron stars in a relativistic model

    CERN Document Server

    Kheto, Apurba

    2014-01-01

    We study the entrainment effect between superfluid neutrons and charge neutral fluid (called the proton fluid) which is made of protons and electrons in neutron star interior in a relativistic model where baryon-baryon interaction is mediated by the exchange of $\\sigma$, $\\omega$ and $\\rho$ mesons. This model also includes scalar self interactions. The entrainment matrix and entrainment parameter are calculated using the parameter set of Glendenning (GL). The inclusion of $\\rho$ meson strongly influences the entrainment parameter ($\\epsilon_{mom}$) in a superfluid neutron star. It is constant at the core and drops to the surface. The entrainment parameter takes values within the physical range.

  17. Magnetized neutron stars with superconducting cores: effect of entrainment

    Science.gov (United States)

    Palapanidis, K.; Stergioulas, N.; Lander, S. K.

    2015-09-01

    We construct equilibrium configurations of magnetized, two-fluid neutron stars using an iterative numerical method. Working in Newtonian framework we assume that the neutron star has two regions: the core, which is modelled as a two-component fluid consisting of type-II superconducting protons and superfluid neutrons, and the crust, a region composed of normal matter. Taking a new step towards more complete equilibrium models, we include the effect of entrainment, which implies that a magnetic force acts on neutrons, too. We consider purely poloidal field cases and present improvements to an earlier numerical scheme for solving equilibrium equations, by introducing new convergence criteria. We find that entrainment results in qualitative differences in the structure of field lines along the magnetic axis.

  18. Axially symmetric equations for differential pulsar rotation with superfluid entrainment

    CERN Document Server

    Antonelli, Marco

    2016-01-01

    We propose an analytical two-components model for pulsar rotational dynamics: the aim is to reduce the 3D hydrodynamical problem to a 1D (radial) problem, using the hypothesis of negligible azimuthal inhomogeneities. The result is the construction of a computationally simple model that takes into account for the non-uniform structure of the star, entrainment effect and differential rotation of the superfluid component. For the first time all these ingredients are treated in a fully consistent way within the picture provided by our initial hypotheses. Our treatment clarifies which are the physical inputs needed to build, to current knowledge, more realistic simulations of rotating neutron stars and gives a neat description of the effect of entrainment when straight vortex lines are considered. Moreover, on this basis, we briefly introduce a new method that can be used to put a constraint to the mass of the pulsars that display very large glitches and to the relative spin up timescales.

  19. On the entrainment rate across a density interface

    Science.gov (United States)

    Nokes, R. I.

    1988-03-01

    Mixed-layer deepening due to grid-generated turbulence is studied experimentally with the aim of explaining the contradictory results of previous studies. Entrainment rates are calculated at fixed distances from the grid in order to avoid the necessity of using an empirical expression for the decay of the turbulent velocity scale. It is shown that an incorrect form of this decay law can cause large errors in the predicted Richardson number dependence of the entrainment rate. For this study this dependence can be expressed as a power law of the form E = KRi exp -1.2. The spread of the results imply that an error of at least + or - 10 percent is realistic in the determination of the exponent. The turbulent velocity decay law is also deduced from the data, and it is found that the decay cannot be represented by a simple power law. Indeed two distinct flow regions, with differing decay rates, are present.

  20. Magnetized neutron stars with superconducting cores: Effect of entrainment

    CERN Document Server

    Palapanidis, K; Lander, S K

    2015-01-01

    We construct equilibrium configurations of magnetized, two-fluid neutron stars using an iterative numerical method. We assume that the neutron star has two regions: the core, which is modelled as a two-component fluid consisting of type-II superconducting protons and superfluid neutrons, and the crust, a region composed of normal matter. Taking a new step towards more complete equilibrium models, we include the effect of entrainment, which implies that a magnetic force acts on neutrons, too. We consider purely poloidal field cases and present improvements to an earlier numerical scheme for solving equilibrium equations, by introducing new convergence criteria. We find that entrainment results in qualitative differences in the structure of field lines across the crust-core boundary and along the magnetic axis.

  1. Entrainment and thrust augmentation in pulsatile ejector flows

    Science.gov (United States)

    Sarohia, V.; Bernal, L.; Bui, T.

    1981-01-01

    This study comprised direct thrust measurements, flow visualization by use of a spark shadowgraph technique, and mean and fluctuating velocity measurements with a pitot tube and linearized constant temperature hot-wire anemometry respectively. A gain in thrust of as much as 10 to 15% was observed for the pulsatile ejector flow as compared to the steady flow configuration. From the velocity profile measurements, it is concluded that this enhanced augmentation for pulsatile flow as compared to a nonpulsatile one was accomplished by a corresponding increased entrainment by the primary jet flow. It is also concluded that the augmentation and total entrainment by a constant area ejector critically depends upon the inlet geometry of the ejector. Experiments were performed to evaluate the influence of primary jet to ejector area ratio, ejector length, and presence of a diffuser on pulsatile ejector performance.

  2. Laboratory Studies of Anomalous Entrainment in Cumulus Cloud Flows

    International Nuclear Information System (INIS)

    Entrainment in cumulus clouds has been a subject of investigation for the last sixty years, and continues to be a central issue in current research. The development of a laboratory facility that can simulate cumulus cloud evolution enables us to shed light on the problem. The apparatus for the purpose is based on a physical model of cloud flow as a plume with off-source diabatic heating that is dynamically similar to the effect of latent-heat release in natural clouds. We present a critical review of the experimental data so far obtained in such facilities on the variation of the entrainment coefficient in steady diabatic jets and plumes. Although there are some unexplained differences among different data sets, the dominant trend of the results compares favourably with recent numerical simulations on steady-state deep convection, and helps explain certain puzzles in the fluid dynamics of clouds.

  3. Updrafts, Downdrafts, Entrainment, and Detrainment in the Giga-LES

    Science.gov (United States)

    Krueger, S. K.; Glenn, I.

    2012-12-01

    We are investigating the properties of evolving three-dimensional updraft and downdraft "cores" in a model dataset from the Giga-LES, a large-domain LES (large-eddy simulation) of tropical oceanic deep convection (Khairoutdinov et al. 2009). We have also applied the analysis method developed by Kuang and Bretherton (2006) to investigate various aspects of the ensemble characteristics of cumulus convection in the Giga-LES. Our results agree with those of Kuang and Bretherton for the cumulus updraft properties. We have examined the relative merits of different entrainment and cloud-top-height assumptions in spectral plume models of cumulus updrafts, the characteristics of downdrafts, and the nature of a rapid transition from shallow to deep convection.isualization of cumulus clouds from the Giga-LES. The realistic structure is associated with entrainment.

  4. Experimental research of liquid entrainment through ADS-4 in AP1000

    International Nuclear Information System (INIS)

    Highlights: • We performed experimental research of liquid entrainment through ADS-4 in AP1000. • Effect of various factors on entrainment at T-junction was conducted. • Visualization research was conducted to make entrainment mechanism clear. - Abstract: In this study, based on a T-junction that consists of Automatic Depressurization System Stage Four (ADS-4) and hot leg in an AP1000 plant, a small-scale experimental research on entrainment at a T-junction was performed. This study mainly focused on the effect of various factors on entrainment, such as the effect of branch size, branch shape and liquid crossflow. The flow pattern map was plotted from the experimental data, and the visualization research indicated that the entrainment phenomena through a large size branch were apparently different from that through a small branch. Three entrainment phenomena were observed in the studies, two entrainment mechanisms could be found in the stratified flow regime entrainment area, the existence of branch contributed to generating intermittent flow in the horizontal main pipe, and the backflow region was observable in the vicinity of a large size branch inlet. Also, experimental research showed that downstream of the branch of T-junction had an important effect on the onset entrainment, and liquid crossflow did not seem to affect the onset entrainment

  5. Chemical Stability of Admixtures Combining Ziconotide with Morphine or Hydromorphone During Simul ated Intrathecal Administration.

    Science.gov (United States)

    Shields, David; Montenegro, Rick; Ragusa, Matthew

    2005-10-01

    Objective.  To determine the stability of admixtures combining ziconotide with morphine or hydromorphone under simulated intrathecal infusions. Materials and Methods.  Admixtures of ziconotide (25 µg/mL) with morphine or hydromorphone (both at 35 mg/mL) were stored in Medtronic SynchroMed® II pumps at 37°C, and in control vials at 37°C and 5°C. Drug concentrations were determined using high-performance liquid chromatography. Results.  The ziconotide pump concentration with morphine declined to 79% of initial in 17 days, and to 88% of initial after 25 days with hydromorphone. Ziconotide concentrations in control vials stored at 37°C displayed similar rates of decay, but vials stored at 5°C exhibited no ziconotide loss. A statistical evaluation of the two combinations shows ziconotide-hydromorphone retaining 80% stability for 40 days (extrapolated), compared to 15 days for ziconotide-morphine. Morphine and hydromorphone were stable in the presence of ziconotide under all conditions. Conclusions.  Ziconotide-hydromorphone admixtures were more stable than ziconotide-morphine admixtures. PMID:22151554

  6. Admixture analysis and stocking impact assessment in brown trout ( Salmo trutta ), estimated with incomplete baseline data

    DEFF Research Database (Denmark)

    Hansen, Michael Møller; Eg Nielsen, Einar; Bekkevold, Dorte; Mensberg, Karen-Lise Dons

    2001-01-01

    . Consequently, stocking had little effect on improving fisheries. In one population, the genetic contribution by domesticated trout was small, whereas in the other population, some genetic impact was suggested. Admixture in this sample of anadromous trout despite absence of stocked domesticated trout could be...

  7. COMPUTER DESIGN OF PROCESSES OF MIGRATION OF ADMIXTURES IN NATURAL WATERS STREAMS

    OpenAIRE

    Savenko, V.; Bondarenko, L.

    2006-01-01

    In work new complex approach of research of processes of transfer of harmful admixtures is offered in natural streams, which is founded on the use of methods of three-dimensional computer design. Basic mathematical equalizations, description of software products, examples of numeral calculations, are resulted on the basis of the offered method

  8. Diffusion Decay Coefficient for Chloride Ions of Concrete Containing Mineral Admixtures

    Directory of Open Access Journals (Sweden)

    Jae-Im Park

    2016-01-01

    Full Text Available The diffusion coefficient for chloride ions and the diffusion decay coefficient for chloride ions are essential variables for a service life evaluation of concrete structures. They are influenced by water-binder ratio, exposure condition, curing temperature, cement type, and the type and use of mineral admixture. Mineral admixtures such as ground granulated blast furnace slag, fly ash, and silica fume have been increasingly used to improve resistance against chloride ions penetration in concrete structures built in an offshore environment. However, there is not enough measured data to identify the statistical properties of diffusion decay coefficient for chloride ions in concrete using mineral admixtures. This paper is aimed at evaluating the diffusion decay coefficient for chloride ions of concrete using ordinary Portland cement or blended cement. NT BUILD 492 method, an electrophoresis experiment, was used to measure the diffusion coefficient for chloride ions with ages. It was revealed from the test results that the diffusion decay coefficient for chloride ions was significantly influenced by W/B and the replacement ratio of mineral admixtures.

  9. Zinc content of commercial diluents widely used in drug admixtures prepared for intravenous infusion.

    Science.gov (United States)

    Desai, Narendra R; Shah, Syed M; Koczone, Julianna; Vencl-Joncic, Maja; Sisto, Christopher; Ludwig, Stephen A

    2007-01-01

    During ongoing quality improvement efforts with two Wyeth parenteral products, Protonix and Zosyn, we noted that dosing solutions prepared from the products yielded inconsistent results on the United States Pharmacopeia Chapter 788 test for subvisible particulates. This manuscript discusses variables that have a direct impact on intravenous products meeting compendial monograph specifications under conditions that are encountered in the clinical setting. The rubber stoppers of vials used for parenteral products, different parts of commercial admixture bags, and the tubing of the administration sets and devices contain residual amounts of metal ions, plasticizers, and other additives incorparated for specific functions. The transition metal ions, including zinc and copper, may leach into drug products during manufacture and during storage of dosing admixture bags prepared for infusion in hospital pharmacies or clinics. The metal ions may compromise the quality of the infusion admixture through catalytic drug degradation and/or generation of undesirable metal ion complexes, which may convert soluble drug molecules into insoluble particulates. To preserve the quality of the drug product, it is essential that metal ion leachables be controlled proactively during manufacture of the drug product; knowledge of metal ion contents in the commercial diluents use for reconstitution, admixture preparation, and flushing of the administration lines is also critical. PMID:23969523

  10. Population admixture, biological invasions and the balance between local adaptation and inbreeding depression

    NARCIS (Netherlands)

    Verhoeven, K.J.F.; Macel, M.; Wolfe, L.M.; Biere, A.

    2011-01-01

    When previously isolated populations meet and mix, the resulting admixed population can benefit from several genetic advantages, including increased genetic variation, the creation of novel genotypes and the masking of deleterious mutations. These admixture benefits are thought to play an important

  11. Phenomenological model of sintering of oxide nuclear fuel with doping admixtures

    Energy Technology Data Exchange (ETDEWEB)

    Baranov, V. G.; Devyatko, Yu. N.; Tenishev, A. V.; Khomyakov, O. V., E-mail: homaykov-o-v@rambler.ru [National Research Nuclear University MEPhI (Moscow Engineering Physics Institute) (Russian Federation)

    2015-12-15

    It is shown that a change in the linear dimension of compacted UO{sub 2} in the sintering process is associated with its plastic yielding under the action of the forces of residual stress and capillary forces. From the curves of sintering of a fuel with doping admixtures in various gaseous media, its rate of creep is reduced.

  12. Recycling of tailings from Korea Molybdenum Corporation as admixture for high-fluidity concrete.

    Science.gov (United States)

    Jung, Moon Young; Choi, Yun Wang; Jeong, Jae Gwon

    2011-01-01

    The main objective of this study is to develop an eco-friendly and a large recycling technique of flotation Tailings from korea (TK) from metal mines as construction materials such as admixtures for high-fluidity concrete (HFC). TK used in this study was obtained from the Korea Molybdenum Corporation in operation. TK was used as the alternative material to adjust flowability and viscosity of HFC in the form of powder agent which enables adjustment of concrete compressive strength. In this study, we have performed concrete rheological tests and concrete flowability tests to obtain the quality characteristics of TK for using as the admixture in producing HFC. The results indicated that the adequate mix ratio of cement to TK should be 8:2 (vol%). It is more effective to use the TK as admixture to control flowability, viscosity and strength of HFC than the normal concrete. It was found that TK could be recycled construction materials in bulk such as admixture for HFC, in terms of the economic and eco-friendly aspects. PMID:21113645

  13. What Causes Birth Order-Intelligence Patterns? The Admixture Hypothesis, Revived.

    Science.gov (United States)

    Rodgers, Joseph Lee

    2001-01-01

    Describes why birth order interests both parents and researchers, discussing what really causes apparent birth order effects on intelligence, examining problems with using cross-sectional intelligence data, and noting how to move beyond cross-sectional inferences. Explains the admixture hypothesis, which finds that family size is much more…

  14. Entrainment of Spontaneously Hypertensive Rat Fibroblasts by Temperature Cycles

    Czech Academy of Sciences Publication Activity Database

    Sládek, Martin; Sumová, Alena

    2013-01-01

    Roč. 8, č. 10 (2013), e77010. E-ISSN 1932-6203 R&D Projects: GA ČR(CZ) GPP305/10/P244; GA ČR(CZ) GAP303/11/0668 Institutional support: RVO:67985823 Keywords : circadian rhythms * temperature * entrainment * SHR * fibroblasts * phase response curve Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 3.534, year: 2013

  15. Entrainment of coarse grains using a discrete particle model

    International Nuclear Information System (INIS)

    Conventional bedload transport models and incipient motion theories relying on a time-averaged boundary shear stress are incapable of accounting for the effects of fluctuating near-bed velocity in turbulent flow and are therefore prone to significant errors. Impulse, the product of an instantaneous force magnitude and its duration, has been recently proposed as an appropriate criterion for quantifying the effects of flow turbulence in removing coarse grains from the bed surface. Here, a discrete particle model (DPM) is used to examine the effects of impulse, representing a single idealized turbulent event, on particle entrainment. The results are classified according to the degree of grain movement into the following categories: motion prior to entrainment, initial dislodgement, and energetic displacement. The results indicate that in all three cases the degree of particle motion depends on both the force magnitude and the duration of its application and suggest that the effects of turbulence must be adequately accounted for in order to develop a more accurate method of determining incipient motion. DPM is capable of simulating the dynamics of grain entrainment and is an appropriate tool for further study of the fundamental mechanisms of sediment transport

  16. Pyrolysis pretreatment of biomass for entrained-flow gasification

    International Nuclear Information System (INIS)

    The biomass for entrained-flow gasification needs to be pretreated to significantly increase its heating value and to make it more readily transportable. The pyrolysis pretreatment was conducted in a lab scale fixed-bed reactor; the reactor was heated to elevate the temperature at 5 °C/min before holding at the desired pyrolysis temperature for 1.5 h a fixed time. The effects of pyrolysis temperature on the yield, composition and heating value of the gaseous, liquid and solid products were determined. The pyrolysis removed most oxygenated constituents of rice straw while significantly increased its energy density. Meantime, it changes the physical properties of biomass powders. The results show that the angle of repose, the angle of internal friction of semi-char decrease obviously; the bulk density of semi-char is bigger than that of biomass. This could favor the feeding of biomass. Considering yield and heating value of the solid semi-char product and the feeding problem, the best pyrolysis temperature was 400 °C. The results of this study have confirmed the feasibility of employing pyrolyzed biomass for entrained-flow gasification; they are useful for the additional studies that will be necessary for designing an efficient biomass entrained-flow gasification system.

  17. Entrainment of respiratory frequency to exercise rhythm during hypoxia.

    Science.gov (United States)

    Paterson, D J; Wood, G A; Marshall, R N; Morton, A R; Harrison, A B

    1987-05-01

    Breathing frequency (f) is often reported as having an integer-multiple relationship to limb movement (entrainment) during rhythmic exercise. To investigate the strength of this coupling while running under hypoxic conditions, two male Caucasians and four male Nepalese porters were tested in the Annapurna region of the Himalayas at altitudes of 915, 2,135, 3,200, 4,420, and 5,030 m. In an additional study in a laboratory at sea level, three male and four female subjects inspired various O2-N2 mixtures [fraction of inspired O2 (FIO2) = 20.93, 17.39, 14.40, 11.81%] that were administered in a single-blind randomized fashion during a treadmill run (40% FIO2 maximum O2 consumption). Breathing and gait signals were stored on FM tape and later processed on a PDP 11/73 computer. The subharmonic relationships between these signals were determined from Fourier analysis (power spectrum), and the coincidence of coupling occurrence was statistically modeled. Entrainment decreased linearly during increasing hypoxia (P less than 0.01). Moreover, a significant linear increase in f occurred during hypoxia (P less than 0.05), whereas stride frequency and metabolic rate remained constant, suggesting that hypoxic-induced increases in f decreased the degree of entrainment. PMID:3597249

  18. Stratocumulus Precipitation and Entrainment Experiment (SPEE) Field Campaign Report

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, Bruce [Univ. of Miami, Miami, FL (United States); Ghate, Virendra [Argonne National Lab. (ANL), Argonne, IL (United States); CADeddu, Maria [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-06-01

    The scientific focus of this project was to examine precipitation and entrainment processes in marine stratocumulus clouds. The entrainment studies focused on characterizing cloud turbulence at cloud top using Doppler cloud radar observations. The precipitation studies focused on characterizing the precipitation and the macroscopic properties (cloud thickness, and liquid water path) of the clouds. This project will contribute to the U.S. Department of Energy (DOE) Atmospheric Radiation Measurement (ARM) Climate Research Facility’s overall objective of providing the remote-sensing observations needed to improve the representation of key cloud processes in climate models. It will be of direct relevance to the components of ARM dealing with entrainment and precipitation processes in stratiform clouds. Further, the radar observing techniques that will be used in this study were developed using ARM Southern Great Plains (SGP) facility observations under Atmospheric System Research (ASR) support. The observing systems operating automatously from a site located just north of the Center for Interdisciplinary Remotely-Piloted Aircraft Studies (CIRPAS) aircraft hangar in Marina, California during the period of 1 May to 4 November 2015 included: 1. Microwave radiometer: ARM Microwave Radiometer, 3-Channel (MWR3C) with channels centered at 23.834, 30, and 89 GHz; supported by Dr. Maria Cadeddu. 2. Cloud Radar: CIRPAS 95 GHz Frequency Modulated Continuous Wave (FMCW) Cloud Radar (Centroid Frequency Chirp Rate [CFCR]); operations overseen by Drs. Ghate and Albrecht. 3. Ceilometer: Vaisala CK-14; operations overseen by Drs. Ghate and Albrecht.

  19. NO emissions in oxy-coal combustion with the addition of steam in an entrained flow reactor

    OpenAIRE

    Álvarez González, Lucía; Riaza Benito, Juan; Gil Matellanes, María Victoria; Pevida García, Covadonga; Pis Martínez, José Juan; Rubiera González, Fernando

    2011-01-01

    The NO emissions of a semi-anthracite and a high-volatile bituminous coal were studied under oxy-fuel combustion conditions in an entrained flow reactor (EFR). The results obtained under oxy-fuel atmospheres (21%O2–79%CO2, 30%O2–70%CO2 and 35%O2–65%CO2), were compared with those produced in air. The replacement of CO2 by 5, 10, and 20% of steam in the oxy-fuel combustion atmospheres was also evaluated in order to study the wet recirculation of flue gas. The NO emissions during oxy-fuel combus...

  20. Genetic analysis of ancestry, admixture and selection in Bolivian and Totonac populations of the New World

    Directory of Open Access Journals (Sweden)

    Watkins W

    2012-05-01

    Full Text Available Abstract Background Populations of the Americas were founded by early migrants from Asia, and some have experienced recent genetic admixture. To better characterize the native and non-native ancestry components in populations from the Americas, we analyzed 815,377 autosomal SNPs, mitochondrial hypervariable segments I and II, and 36 Y-chromosome STRs from 24 Mesoamerican Totonacs and 23 South American Bolivians. Results and Conclusions We analyzed common genomic regions from native Bolivian and Totonac populations to identify 324 highly predictive Native American ancestry informative markers (AIMs. As few as 40–50 of these AIMs perform nearly as well as large panels of random genome-wide SNPs for predicting and estimating Native American ancestry and admixture levels. These AIMs have greater New World vs. Old World specificity than previous AIMs sets. We identify highly-divergent New World SNPs that coincide with high-frequency haplotypes found at similar frequencies in all populations examined, including the HGDP Pima, Maya, Colombian, Karitiana, and Surui American populations. Some of these regions are potential candidates for positive selection. European admixture in the Bolivian sample is approximately 12%, though individual estimates range from 0–48%. We estimate that the admixture occurred ~360–384 years ago. Little evidence of European or African admixture was found in Totonac individuals. Bolivians with pre-Columbian mtDNA and Y-chromosome haplogroups had 5–30% autosomal European ancestry, demonstrating the limitations of Y-chromosome and mtDNA haplogroups and the need for autosomal ancestry informative markers for assessing ancestry in admixed populations.

  1. The Role of Recent Admixture in Forming the Contemporary West Eurasian Genomic Landscape

    Science.gov (United States)

    Busby, George B.J.; Hellenthal, Garrett; Montinaro, Francesco; Tofanelli, Sergio; Bulayeva, Kazima; Rudan, Igor; Zemunik, Tatijana; Hayward, Caroline; Toncheva, Draga; Karachanak-Yankova, Sena; Nesheva, Desislava; Anagnostou, Paolo; Cali, Francesco; Brisighelli, Francesca; Romano, Valentino; Lefranc, Gerard; Buresi, Catherine; Ben Chibani, Jemni; Haj-Khelil, Amel; Denden, Sabri; Ploski, Rafal; Krajewski, Pawel; Hervig, Tor; Moen, Torolf; Herrera, Rene J.; Wilson, James F.; Myers, Simon; Capelli, Cristian

    2015-01-01

    Summary Over the past few years, studies of DNA isolated from human fossils and archaeological remains have generated considerable novel insight into the history of our species. Several landmark papers have described the genomes of ancient humans across West Eurasia, demonstrating the presence of large-scale, dynamic population movements over the last 10,000 years, such that ancestry across present-day populations is likely to be a mixture of several ancient groups [1, 2, 3, 4, 5, 6, 7]. While these efforts are bringing the details of West Eurasian prehistory into increasing focus, studies aimed at understanding the processes behind the generation of the current West Eurasian genetic landscape have been limited by the number of populations sampled or have been either too regional or global in their outlook [8, 9, 10, 11]. Here, using recently described haplotype-based techniques [11], we present the results of a systematic survey of recent admixture history across Western Eurasia and show that admixture is a universal property across almost all groups. Admixture in all regions except North Western Europe involved the influx of genetic material from outside of West Eurasia, which we date to specific time periods. Within Northern, Western, and Central Europe, admixture tended to occur between local groups during the period 300 to 1200 CE. Comparisons of the genetic profiles of West Eurasians before and after admixture show that population movements within the last 1,500 years are likely to have maintained differentiation among groups. Our analysis provides a timeline of the gene flow events that have generated the contemporary genetic landscape of West Eurasia. PMID:26387712

  2. African Ancestry Analysis and Admixture Genetic Mapping for Proliferative Diabetic Retinopathy in African Americans

    Science.gov (United States)

    Tandon, Arti; Chen, Ching J.; Penman, Alan; Hancock, Heather; James, Maurice; Husain, Deeba; Andreoli, Christopher; Li, Xiaohui; Kuo, Jane Z.; Idowu, Omolola; Riche, Daniel; Papavasilieou, Evangelia; Brauner, Stacey; Smith, Sataria O.; Hoadley, Suzanne; Richardson, Cole; Kieser, Troy; Vazquez, Vanessa; Chi, Cheryl; Fernandez, Marlene; Harden, Maegan; Cotch, Mary Frances; Siscovick, David; Taylor, Herman A.; Wilson, James G.; Reich, David; Wong, Tien Y.; Klein, Ronald; Klein, Barbara E. K.; Rotter, Jerome I.; Patterson, Nick; Sobrin, Lucia

    2015-01-01

    Purpose. To examine the relationship between proportion of African ancestry (PAA) and proliferative diabetic retinopathy (PDR) and to identify genetic loci associated with PDR using admixture mapping in African Americans with type 2 diabetes (T2D). Methods. Between 1993 and 2013, 1440 participants enrolled in four different studies had fundus photographs graded using the Early Treatment Diabetic Retinopathy Study scale. Cases (n = 305) had PDR while controls (n = 1135) had nonproliferative diabetic retinopathy (DR) or no DR. Covariates included diabetes duration, hemoglobin A1C, systolic blood pressure, income, and education. Genotyping was performed on the Affymetrix platform. The association between PAA and PDR was evaluated using logistic regression. Genome-wide admixture scanning was performed using ANCESTRYMAP software. Results. In the univariate analysis, PDR was associated with increased PAA (odds ratio [OR] = 1.36, 95% confidence interval [CI] = 1.16–1.59, P = 0.0002). In multivariate regression adjusting for traditional DR risk factors, income and education, the association between PAA and PDR was attenuated and no longer significant (OR = 1.21, 95% CI = 0.59–2.47, P = 0.61). For the admixture analyses, the maximum genome-wide score was 1.44 on chromosome 1. Conclusions. In this largest study of PDR in African Americans with T2D to date, an association between PAA and PDR is not present after adjustment for clinical, demographic, and socioeconomic factors. No genome-wide significant locus (defined as having a locus-genome statistic > 5) was identified with admixture analysis. Further analyses with even larger sample sizes are needed to definitively assess if any admixture signal for DR is present. PMID:26098467

  3. Reaction kinetics of solid fuels during entrained flow gasification

    Energy Technology Data Exchange (ETDEWEB)

    Tremel, Alexander

    2012-10-24

    Despite the application of entrained flow gasification on larger scales, the reaction rates in the hot conversion zone are almost unknown. But the knowledge of the rates of the gasification reactions at high temperature and high pressure is crucial for the detailed design and optimisation of these gasifiers. This dissertation provides measurements of fuel conversion under operation conditions relevant to industrial gasifiers and aims at the transfer of the data to larger scale applications. A novel pilot-scale research reactor is developed that enables the study of gasification reactions at high temperature, high pressure and under entrained flow conditions. The Pressurised High Temperature Entrained Flow Reactor (PiTER) is operated at up to 1600 C and 4.0 MPa in pyrolysis and gasification experiments. The data set is extended by measurements in an atmospheric entrained flow reactor and a pressurised wire mesh reactor. Devolatilisation and gasification behaviour of a wide range of fuels is analysed including anthracite, bituminous coal, lignite, biocoal (from hydrothermal carbonisation), and biomass; however, Rhenish lignite is used in most of the experiments. The pyrolysis data enable the validation of a simple first order reaction model that describes the influence of pressure, temperature, and residence time on volatile yield. Char samples collected from the three reactors are analysed using laboratory procedures and bench-scale setups. Specific char surface area is measured by CO{sub 2} adsorption at 273 K, and is found to be significantly influenced by char conversion, reaction temperature, and devolatilisation pressure. The surface data are described by an extension of the Random Pore Model. Intrinsic char reactivity is measured in a pressurised thermogravimetric analyser and the influence of reactant partial pressure and temperature on the char-CO{sub 2} and char-H{sub 2}O reaction is studied. The intrinsic reaction rate is described by nth order and

  4. Audience entrainment during live contemporary dance performance: Physiological and cognitive measures

    Directory of Open Access Journals (Sweden)

    Asaf Bachrach

    2015-05-01

    Full Text Available Perceiving and synchronizing to a piece of dance is a remarkable skill in humans. Research in this area is very recent and has been focused mainly on entrainment produced by regular rhythms. Here, we investigated entrainment effects on spectators perceiving a non-rhythmic and extremely slow performance issued from contemporary dance. More specifically, we studied the relationship between subjective experience and entrainment produced by perceiving this type of performance. We defined two types of entrainment. Physiological entrainment corresponded to cardiovascular and respiratory coordinated activities. Cognitive entrainment was evaluated through cognitive tasks that quantified time distortion. These effects were thought to reflect attunement of a participant' internal temporal clock to the particularly slow pace of the danced movement. Each participant' subjective experience – in the form of responses to questionnaires – were collected and correlated with cognitive and physiological entrainment. We observe: a a positive relationship between psychological entrainment and attention to breathing (their own one or that of dancers; b a positive relationship between cognitive entrainment (reflected as an under-estimation of time following the performance and attention to their own breathing, and attention to the muscles’ dancers. Overall, our results suggest a close relationship between attention to breathing and entrainment. This proof-of-concept pilot study was intended to prove the feasibility of a quantitative situated paradigm. This research is inscribed in a large-scale interdisciplinary project of dance spectating (labodanse.org.

  5. Audience entrainment during live contemporary dance performance: physiological and cognitive measures.

    Science.gov (United States)

    Bachrach, Asaf; Fontbonne, Yann; Joufflineau, Coline; Ulloa, José Luis

    2015-01-01

    Perceiving and synchronizing to a piece of dance is a remarkable skill in humans. Research in this area is very recent and has been focused mainly on entrainment produced by regular rhythms. Here, we investigated entrainment effects on spectators perceiving a non-rhythmic and extremely slow performance issued from contemporary dance. More specifically, we studied the relationship between subjective experience and entrainment produced by perceiving this type of performance. We defined two types of entrainment. Physiological entrainment corresponded to cardiovascular and respiratory coordinated activities. Cognitive entrainment was evaluated through cognitive tasks that quantified time distortion. These effects were thought to reflect attunement of a participant' internal temporal clock to the particularly slow pace of the danced movement. Each participant' subjective experience-in the form of responses to questionnaires-were collected and correlated with cognitive and physiological entrainment. We observe: (a) a positive relationship between psychological entrainment and attention to breathing (their own one or that of dancers); and (b) a positive relationship between cognitive entrainment (reflected as an under-estimation of time following the performance) and attention to their own breathing, and attention to the muscles' dancers. Overall, our results suggest a close relationship between attention to breathing and entrainment. This proof-of-concept pilot study was intended to prove the feasibility of a quantitative situated paradigm. This research is inscribed in a large-scale interdisciplinary project of dance spectating (labodanse.org). PMID:25999831

  6. Growth of fractal structures in flames with silicon admixture

    OpenAIRE

    Smirnov, B. M.; Dutka, M.; van Essen, V. M.; Gersen, S.; Visser, P.; Vainchtein, D.; De Hosson, J.Th.M.; Levinsky, H.B.; Mokhov, A. V.

    2012-01-01

    Transmission electron microscopy (TEM) measurements and theoretical analysis are combined to construct the physical picture of formation of SiO2 fractal aggregates in a methane/hexamethyldisiloxane/air atmospheric pressure flame. The formation of SiO2 fractal aggregates is described as a multistage process. The first stage is combustion of fuel in a narrow flame front region with formation of main combustion products including SiO2 molecules. Further downstream SiO2 molecules join in liquid n...

  7. Doing Duo – a Case Study of Entrainment in William Forsythe’s Choreography Duo

    Directory of Open Access Journals (Sweden)

    Elizabeth eWaterhouse

    2014-10-01

    Full Text Available Entrainment theory focuses on processes in which interacting (i.e. coupled rhythmic systems stabilize, producing synchronization in the ideal sense, and forms of phase related rhythmic coordination in complex cases. In human action, entrainment involves spatiotemporal and social aspects, characterizing the meaningful activities of music, dance, and communication. How can the phenomenon of human entrainment be meaningfully studied in complex situations such as dance? We present an in-progress case study of entrainment in William Forsythe's choreography Duo, a duet in which coordinated rhythmic activity is achieved without an external musical beat and without touch-based interaction. Using concepts of entrainment from different disciplines as well as insight from Duo performer Riley Watts, we question definitions of entrainment in the context of dance. The functions of chorusing, turn-taking, complementary action, cues and alignments are discussed and linked to supporting annotated video material. While Duo challenges the definition of entrainment in dance as coordinated response to an external musical or rhythmic signal, it supports the definition of entrainment as coordinated interplay of motion and sound production by active agents (i.e., dancers in the field. Agreeing that human entrainment should be studied on multiple levels, we suggest that entrainment between the dancers in Duo is elastic in time and a propose how to test this hypothesis empirically. We do not claim that our proposed model of elasticity is applicable to all forms of human entrainment nor to all to examples of entrainment in dance. Rather, we suggest studying higher order phase correction (the stabilizing tendency of entrainment as a potential aspect to be incorporated into other models.

  8. Doing Duo - a case study of entrainment in William Forsythe's choreography "Duo".

    Science.gov (United States)

    Waterhouse, Elizabeth; Watts, Riley; Bläsing, Bettina E

    2014-01-01

    Entrainment theory focuses on processes in which interacting (i.e., coupled) rhythmic systems stabilize, producing synchronization in the ideal sense, and forms of phase related rhythmic coordination in complex cases. In human action, entrainment involves spatiotemporal and social aspects, characterizing the meaningful activities of music, dance, and communication. How can the phenomenon of human entrainment be meaningfully studied in complex situations such as dance? We present an in-progress case study of entrainment in William Forsythe's choreography Duo, a duet in which coordinated rhythmic activity is achieved without an external musical beat and without touch-based interaction. Using concepts of entrainment from different disciplines as well as insight from Duo performer Riley Watts, we question definitions of entrainment in the context of dance. The functions of chorusing, turn-taking, complementary action, cues, and alignments are discussed and linked to supporting annotated video material. While Duo challenges the definition of entrainment in dance as coordinated response to an external musical or rhythmic signal, it supports the definition of entrainment as coordinated interplay of motion and sound production by active agents (i.e., dancers) in the field. Agreeing that human entrainment should be studied on multiple levels, we suggest that entrainment between the dancers in Duo is elastic in time and propose how to test this hypothesis empirically. We do not claim that our proposed model of elasticity is applicable to all forms of human entrainment nor to all examples of entrainment in dance. Rather, we suggest studying higher order phase correction (the stabilizing tendency of entrainment) as a potential aspect to be incorporated into other models. PMID:25374522

  9. An experimental investigation of flow patterns and liquid entrainment in a horizontal-tube evaporator

    Science.gov (United States)

    Barnhart, John Steven

    An experimental study of two-phase flow patterns and droplet entrainment in a horizontal-tube evaporator was conducted. Measurements were made with serpentine aluminum and glass evaporators with geometries typical of those used for domestic refrigeration. The refrigerant in the majority of tests was R134a, which will replace R12 for refrigeration and automotive air-conditioning in 1995. The phenomenon of primary interest was the nonequilibrium transport of droplets within superheated vapor at the evaporator exit. Of particular concern were substantial variations in the liquid rate with time, and corresponding fluctuations in exit temperature. These variations are due to the formation of slugs which rapidly transport a surplus of liquid toward the exit. A flow loop was constructed to circulate oil-free refrigerant through the evaporator under widely varying conditions. Liquid carry over (expressed as a dimensionless entrained mass fraction, EMF) was measured as a function of inlet quality, heat flux, mass flux, and exit superheat. A laser-based phase/Doppler particle analyzer was used to measure droplet diameters and velocities at the evaporator exit. Tests with three refrigerants over wide ranges of operating conditions revealed time-averaged EMF's of no more than 0.1 percent. Analysis of variance showed exit superheat to have the strongest effect, followed by mass flux, inlet quality, and heat flux. Time-averaged EMF's varied with operating conditions by several orders of magnitude, decreasing with increasing superheat level (due to lower entrainment rates near the exit and more rapid droplet vaporization) and mass flux and inlet quality (due to reduced slug formation). The incidence of slug flow and its effect on evaporator exit conditions were documented in time-resolved experiments, using techniques such as auto- and cross-correlation and Fourier transform. Time-resolved EMF's as high as one percent were observed, as well as sharp reductions in exit superheat

  10. Development of admixture mapping panels for African Americans from commercial high-density SNP arrays

    Directory of Open Access Journals (Sweden)

    Dunston Georgia M

    2010-07-01

    Full Text Available Abstract Background Admixture mapping is a powerful approach for identifying genetic variants involved in human disease that exploits the unique genomic structure in recently admixed populations. To use existing published panels of ancestry-informative markers (AIMs for admixture mapping, markers have to be genotyped de novo for each admixed study sample and samples representing the ancestral parental populations. The increased availability of dense marker data on commercial chips has made it feasible to develop panels wherein the markers need not be predetermined. Results We developed two panels of AIMs (~2,000 markers each based on the Affymetrix Genome-Wide Human SNP Array 6.0 for admixture mapping with African American samples. These two AIM panels had good map power that was higher than that of a denser panel of ~20,000 random markers as well as other published panels of AIMs. As a test case, we applied the panels in an admixture mapping study of hypertension in African Americans in the Washington, D.C. metropolitan area. Conclusions Developing marker panels for admixture mapping from existing genome-wide genotype data offers two major advantages: (1 no de novo genotyping needs to be done, thereby saving costs, and (2 markers can be filtered for various quality measures and replacement markers (to minimize gaps can be selected at no additional cost. Panels of carefully selected AIMs have two major advantages over panels of random markers: (1 the map power from sparser panels of AIMs is higher than that of ~10-fold denser panels of random markers, and (2 clusters can be labeled based on information from the parental populations. With current technology, chip-based genome-wide genotyping is less expensive than genotyping ~20,000 random markers. The major advantage of using random markers is the absence of ascertainment effects resulting from the process of selecting markers. The ability to develop marker panels informative for ancestry from

  11. Coal and char properties in high temperature entrained flow gasification

    International Nuclear Information System (INIS)

    With the objective to measure coal conversion at realistic operation conditions the Pressurised High Temperature Entrained Flow Reactor (PiTER) is developed. The pyrolysis of Rhenish lignite is studied at temperatures up to 1600 °C and pressures up to 2.5 MPa. At longer residence time (above 1.5 s) volatile yield is 68 wt% and independent of temperature and pressure. Char samples are extracted from the hot reaction zone and their reactivity is analysed by weight loss in TGA experiments at defined conditions. Furthermore, specific char surface area is measured. At 1200 °C the intrinsic reactivity of char decreases by a factor of almost 7 from 0.5 s to 2 s residence time, but surface area (approximately 500 m2/g) is hardly affected. At 1400 °C and 1600 °C, the intrinsic reactivity also decreases, but simultaneously the surface area is reduced to below 300 m2/g. The difference in deactivation can only be explained by two different mechanisms: (i) experiments at 1200 °C are below the ash fusion temperature and graphitisation at the char surface may lead to a reorganisation of carbon atoms; (ii) above the ash fusion temperature, the melting of mineral matter additionally blocks the micropore structure and results in a loss of specific surface area. -- Highlights: ► Development of a novel pilot scale entrained flow research reactor. ► Pyrolysis at up to 1600 °C and up to 2.5 MPa under entrained flow conditions. ► Surface area of char significantly decreases above the ash melting temperature. ► Intrinsic reactivity of char is dependent on heat treatment severity. ► Thermal annealing affects char reactivity, even at short residence time.

  12. SEQUENTIAL RADIOCHEMICAL ANALYSIS FOR RUTHENIUM, STRONTIUM AND CESIUM IN ENVIRONMENTAL AIR

    Science.gov (United States)

    In routine surveillance operations, the radionuclide measurement of air discharged from an operating nuclear facility involves the entrainment of radionuclides on selective filter or absorptive media, and the determination of their gross beta activity. However, a more sensitive t...

  13. Analysis and numerical simulation of a laboratory analog of radiatively induced cloud-top entrainment

    Science.gov (United States)

    Schmidt, Heiko; Kerstein, Alan R.; Wunsch, Scott; Nédélec, Renaud; Sayler, Ben J.

    2013-06-01

    Numerical simulations using the one-dimensional-turbulence (ODT) model are compared to water-tank measurements emulating convection and entrainment in stratiform clouds driven by cloud-top cooling. Measured dependences of the entrainment rate on Richardson number were numerically reproduced for water trials in which the initial stratification is due to temperature differences. For an additional set of trials where the initial stratification is obtained by adding dextrose to the lower layer of the tank, measured dependences of the entrainment rate on Richardson number were partially reproduced, and importantly, the model also captures the measured sensitivity of entrainment to molecular transport. Additional parameter variations suggest other dependences of the entrainment rate. Analysis suggests possible qualitative differences between laboratory and cloud entrainment behaviors that might be testable using ODT.

  14. A Heart for Interaction: Physiological Entrainment and Behavioral Coordination in a Collective, Creative Construction Task

    CERN Document Server

    Fusaroli, Riccardo; Roepstoff, Andreas; Tylén, Kristian

    2015-01-01

    Interpersonal physiological entrainment is increasingly argued to underlie rapport, empathy and even team performance. Inspired by the model of interpersonal synergy, we investigate the presence, temporal development, possible mechanisms and impact of interpersonal heart rate entrainment during individual and collective creative LEGO construction tasks. In Study 1 we show how HR entrainment is driven by a plurality of sources including task constraints and behavioral coordination. Generally, HR entrainment is more prevalent in individual trials (involving participants doing the same things) than in collective ones (involving participants taking turns and performing complementary actions). However, when contrasted against virtual pairs, collective trials display more stable HR entrainment supporting the idea that online social interaction plays a role. Furthermore, HR entrainment is found to grow across collective but not individual trials. In Study 2 we further show that in collective trials the dynamics of H...

  15. Water entrainment in intercompartmental flows resulting from pipeline breaks: literature study. Topical report

    International Nuclear Information System (INIS)

    The extensive engineering literature on two-phase flow in ducts, nozzles and orifices is reviewed with respect to intercompartmental flows in nuclear reactor safety applications. The topics of flow patterns, holdup or slip, two-phase critical flow and entrainment are reviewed and discussed. The entrainment fraction of droplets in the vapor phase of an annular flow pattern can be estimated in the case of vertical or horizontal steady duct flow at positions well downstream from the duct entrance. No general correlation for the prediction of entrainment is available, however. In addition the literature pertaining to nuclear containment calculation methods, experiments, calculation surveys and verifications is surveyed. The containment analysis methods are quite comprehensive and well-developed. Currently no models for estimating entrainment in containment problems are being used, but entrainment has been treated as an arbitrary parameter and some attention has been given to entrainment in the interpretation of experiments

  16. Entrainment characteristics of unsteady subsonic jets. [for V/STOL aircraft

    Science.gov (United States)

    Platzer, M. F.; Simmons, J. M.; Bremhorst, K.

    1979-01-01

    The effectiveness of jet unsteadiness in enhancing flow entrainment was assessed. It was conducted that entrainment depends on the type and amount of jet unsteadiness. Apparently, the mere introduction of jet unsteadiness by small sinusoidal flow angle variations is insufficient to enhance entrainment but, it should be noted that the results were obtained at measuring stations which are all many nozzle widths downstream of the jet nozzle. Thus, no fully conclusive statement can be made at this time about the entrainment close to the nozzle. The high entrainment of the fluidically oscillated jet was caused by the high-frequency content of this square wave type of oscillation but more detailed measurements are clearly needed, in particular for the fluidically oscillated and the pulsed jets. Practical ejector application requires the proper trade-off between entrainment and primary nozzle thrust efficiency.

  17. Entrainment in the Near and Far Field of Fire Plumes

    OpenAIRE

    Cetegen, B. M.; Zukoski, E. E.; Kubota, T.

    1984-01-01

    This paper describes entrainment measurements made in fire plumes with a new technique. Measurements were in plumes rising from natural gas diffusion flames stabilized on 0.10, 0.19 and 0.50 m diameter burners and the heat release rates ranged from 10 to 200 kW. The heights examined ranged from elevations starting very close to the burner surface to distances about five times the average flame heights. Experiments indicate the presence of three regions: a region close to the burner surface wh...

  18. Entrained Flow Reactor Test of Potassium Capture by Kaolin

    OpenAIRE

    Wang, Guoliang; Jensen, Peter Arendt; Hao WU; Bøjer, Martin; Jappe Frandsen, Flemming; Glarborg, Peter

    2015-01-01

    In the present study a method to simulate the reaction between gaseous KCl and kaolin at suspension fired condition was developed using a pilot-scale entrained flow reactor (EFR). Kaolin was injected into the EFR for primary test of this method. By adding kaolin, KCl can effectively be captured, forming water-insoluble K-aluminosilicate. The amount of K captured by 1 g kaolin rose when increasing the molar ratio of K/Si in the reactant. Changing of reaction temperature from 1100 °C to 1300 °C...

  19. Entrained Flow Reactor Test of Potassium Capture by Kaolin

    DEFF Research Database (Denmark)

    Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao;

    2015-01-01

    In the present study a method to simulate the reaction between gaseous KCl and kaolin at suspension fired condition was developed using a pilot-scale entrained flow reactor (EFR). Kaolin was injected into the EFR for primary test of this method. By adding kaolin, KCl can effectively be captured......, forming water-insoluble K-aluminosilicate. The amount of K captured by 1 g kaolin rose when increasing the molar ratio of K/Si in the reactant. Changing of reaction temperature from 1100 °C to 1300 °C did not influence the extent of reaction, which is different from the results observed in previous fixed...

  20. Helium flooded cryopump with increased hydrogen and helium entrainment factor

    International Nuclear Information System (INIS)

    Superhigh-vacuum helium condensation-sorption pump with H2 and H entrainment factors 1.7 and 3.1 times respectively exceeding those in the known design cryopumps with the same diameters of casings and connecting flange flow sections is described. The N2 pumping-out rate is 6m3/s, the H2 one is 21 m3/s, the H2 pumping-out rate constitutes 12m3/s, the casing diameter is 0.5, the height - 0.8m, mass-35 kg. The pump is fabricated of titanium and aluminium

  1. Separation of Erucic Acid from Rape-Seed Oil Using Supercritical Carbon Dioxide with Entrainer

    Institute of Scientific and Technical Information of China (English)

    云志; 钱仁渊; 等

    2002-01-01

    Separation of erucic acid from rape-seed oil using supercritical carbon dioxide with entrainer was carried on a pilot column with an inner diameter 14 mm and an effective total height 2.2m.Experiments were focused on the effects of entrainers.i.e.acetone.ethanol and ethyl acetate,on the extraction.It is showed that entrainers made selectivity lower,but separation time shorter.

  2. Are non-human primates capable of rhythmic entrainment? Evidence for the gradual audiomotor evolution hypothesis

    OpenAIRE

    HugoMerchant; HenkjanHoning

    2014-01-01

    We propose a decomposition of the neurocognitive mechanisms that might underlie interval-based timing and rhythmic entrainment. Next to reviewing the concepts central to the definition of rhythmic entrainment, we discuss recent studies that suggest rhythmic entrainment to be specific to humans and a selected group of bird species, but, surprisingly, is not obvious in non-human primates. On the basis of these studies we propose the gradual audiomotor evolution hypothesis that suggests that hum...

  3. In time with the music : the concept of entrainment and its significance for ethnomusicology.

    OpenAIRE

    Clayton, Martin; Sager, Rebecca; Will, Udo

    2005-01-01

    Entrainment, broadly defined, is a phenomenon in which two or more independent rhythmic processes synchronize with each other. To illuminate the significance of entrainment for various directions of music research and promote a nuanced understanding of the concept among ethnomusicologists, this publication opens with an exposition of entrainment research in various disciplines, from physics to linguistics and psychology, while systematically introducing basic concepts that are directly releva...

  4. Impact of entrainment and impingement on fish populations in the Hudson River estuary. Volume I. Entrainment-impact estimates for six fish populations inhabiting the Hudson River estuary

    Energy Technology Data Exchange (ETDEWEB)

    Boreman, J.; Barnthouse, L.W.; Vaughn, D.S.; Goodyear, C.P.; Christensen, S.W.; Kumar, K.D.; Kirk, B.L.; Van Winkle, W.

    1982-01-01

    This volume is concerned with the estimation of the direct (or annual) entrainment impact of power plants on populations of striped bass, white perch, Alosa spp. (blueback herring and alewife), American shad, Atlantic tomcod, and bay anchovy in the Hudson River estuary. Entrainment impact results from the killing of fish eggs, larvae, and young juveniles that are contained in the cooling water cycled through a power plant. An Empirical Transport Model (ETM) is presented as the means of estimating a conditional entrainment mortality rate (defined as the fraction of a year class which would be killed due to entrainment in the absence of any other source of mortality). Most of this volume is concerned with the estimation of several parameters required by the ETM: physical input parameters (e.g., power-plant withdrawal flow rates); the longitudinal distribution of ichthyoplankton in time and space; the duration of susceptibility of the vulnerable organisms; the W-factors, which express the ratios of densities of organisms in power plant intakes to densities of organisms in the river; and the entrainment mortality factors (f-factors), which express the probability that an organism will be killed if it is entrained. Once these values are obtained, the ETM is used to estimate entrainment impact for both historical and projected conditions.

  5. Impact of entrainment and impingement on fish populations in the Hudson River estuary. Volume I. Entrainment-impact estimates for six fish populations inhabiting the Hudson River estuary

    International Nuclear Information System (INIS)

    This volume is concerned with the estimation of the direct (or annual) entrainment impact of power plants on populations of striped bass, white perch, Alosa spp. (blueback herring and alewife), American shad, Atlantic tomcod, and bay anchovy in the Hudson River estuary. Entrainment impact results from the killing of fish eggs, larvae, and young juveniles that are contained in the cooling water cycled through a power plant. An Empirical Transport Model (ETM) is presented as the means of estimating a conditional entrainment mortality rate (defined as the fraction of a year class which would be killed due to entrainment in the absence of any other source of mortality). Most of this volume is concerned with the estimation of several parameters required by the ETM: physical input parameters (e.g., power-plant withdrawal flow rates); the longitudinal distribution of ichthyoplankton in time and space; the duration of susceptibility of the vulnerable organisms; the W-factors, which express the ratios of densities of organisms in power plant intakes to densities of organisms in the river; and the entrainment mortality factors (f-factors), which express the probability that an organism will be killed if it is entrained. Once these values are obtained, the ETM is used to estimate entrainment impact for both historical and projected conditions

  6. Shrinkage and cracking behavior of high performance concretes containing chemical admixtures

    Institute of Scientific and Technical Information of China (English)

    亓萌; 李宗津; 马保国

    2002-01-01

    Modern concretes often incorporate several chemical admixtures to alter the properties of fresh or hardened concrete. In this work, the influences of three types of chemical admixtures, calcium nitrite inhibitor (CNI), retarder (D-17) and superplasticizer (W-19) on free shrinkage and restrained shrinkage cracking of high performance concrete were experimentally investigated. The test results showed that, with the same water to binder ratio (0.4), mixtures containing D-17 of 0.25 percent or higher ratio of W-19 (2.76 percent) all exhibited a reduction in free shrinkage and shrinkage cracking width. However, the incorporations of various ratios of CNI into mixtures led to an increase in free shrinkage and shrinkage cracking width as compared to control mixture. In order to study the influence of CNI, the microstructure of concrete mixture containing CNI were investigated by Mercury Intrusion Porosimetry as well as Scanning Electronic Microscopy(SEM) technique.

  7. Standard test method for initial screening of corrosion inhibiting admixtures for steel in concrete

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This test method covers a procedure for determining the effects of chemical admixtures on the corrosion of metals in concrete. This test method can be used to evaluate materials intended to inhibit chloride-induced corrosion of steel in concrete. It can also be used to evaluate the corrosivity of admixtures by themselves or in a chloride environment. This test is not applicable for emulsions. 1.2 &solely-SI-units; 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  8. The origin of early age expansions induced in cementitious materials containing shrinkage reducing admixtures

    International Nuclear Information System (INIS)

    Studies on the early-age shrinkage behavior of cement pastes, mortars, and concretes containing shrinkage reducing admixtures (SRAs) have indicated these mixtures frequently exhibit an expansion shortly after setting. While the magnitude of the expansion has been noted to be a function of the chemistry of the cement and the admixture dosage; the cause of the expansion is not clearly understood. This investigation uses measurements of autogenous deformation, X-ray diffraction, pore solution analysis, thermogravimetry, and scanning electron microscopy to study the early-age properties and describe the mechanism of the expansion in OPC pastes made with and without SRA. The composition of the pore solution indicates that the presence of the SRA increases the portlandite oversaturation level in solution which can result in higher crystallization stresses which could lead to an expansion. This observation is supported by deformation calculations for the systems examined.

  9. Experimental studies on spray and gas entrainment characteristics of biodiesel fuel: Implications of gas entrained and fuel oxygen content on soot formation

    International Nuclear Information System (INIS)

    Experiments were performed inside the constant volume vessel to simulate the real diesel engine conditions. The LIF–PIV (Laser Induced Florescence – Particulate Image Velocimetry) technique was used to characterize the spray and gas entrainment characteristics of the fuels while the OH-chemiluminescence and two color pyrometry were applied to obtain information about the combustion processes. Biodiesel from palm oil (BDF (Biodiesel Fuel)) and the JIS #2 diesel fuel were utilized. It was observed that the SMD (Sauter mean diameter) obtained through an empirical equation decreased by increasing the injection pressure from 100 to 300 MPa and reducing the nozzle diameter from 0.16 to 0.08 mm. BDF has higher SMD values compared to diesel thus signifying inferior atomization. By increasing the injection pressure up to 300 MPa and reducing the nozzle diameter to 0.08 mm, the normal velocity and total mass flow rate of the entrained gas by the fuels increased. Due to higher viscosity and density properties, BDF possessed inferior atomization characteristics which made the normal velocity and total mass flow rate of the entrained gas lower compared to diesel. Due to inferior atomization which led to less gas being entrained upstream of the lift-off flame, the fuel oxygen content in BDF played a significant role in soot formation processes. - Highlights: • Spray and gas entrainment characteristics of biodiesel (BDF (Biodiesel Fuel)) and fuel were investigated. • Effect of injector parameters on BDF spray and gas entrainment characteristics was identified. • Higher viscosity and density of BDF yielded inferior spray atomization processes. • Gas entrainment velocity and mass flow rate of gas entrained by BDF lower. • Gas entrained had less effect on BDF's soot formation

  10. Effects of liquid properties on gas entrainment phenomenon induced by vortices in an LMFBR

    International Nuclear Information System (INIS)

    Free surface vortices often induce a deep surface dimple, known as a gas core, which causes gas bubble entrainment into the liquid from the gas core tip. To predict the gas entrainment induced by vortices, the establishment of similarity law for the fluid properties and scaling on the onset of gas entrainment is required. Experiments to determine the condition necessary for the onset of gas entrainment have been performed. The viscosity and surface tension of liquid were dominant properties determining gas entrainment inception. A simple model was used to interpret these results and a gas entrainment criterion was proposed. In modeling the gas entrainment vortices, the velocity distribution around the vortex and the gas core shape was approximated by a stretching vortex model. From the balance of inertial force by the downward flow with surface tension at the gas core tip, the relationship between Reynolds, Weber and rotational Froude numbers was determined at the gas entrainment critical condition. The theoretical gas entrainment criterion could predict the experimental results satisfactorily

  11. THEORY OF ACTIVE HITTINGS IS IN PROCESSES OF ELECTRO-COAGULATION THE ADMIXTURES IN WATER TECHNOLOGICAL ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    В.В. Березуцький

    2012-10-01

    Full Text Available  In the article theoretical bases of electro-coagulation of admixtures are examined in a water technological environment with the use of theory of the active hittings, which are based on the results of the executed researches and analysis of scientific information. Application of theory of the active hittings is in coagulation, provides high efficiency of process of extraction of admixtures from water environments during minimization of energy consumption and expenses of materials.

  12. Genome-wide Scan of 29,141 African Americans Finds No Evidence of Directional Selection since Admixture

    OpenAIRE

    Bhatia, Gaurav; Tandon, Arti; Patterson, Nick; Aldrich, Melinda C.; Ambrosone, Christine B.; Amos, Christopher; Bandera, Elisa V.; Berndt, Sonja I.; Bernstein, Leslie; Blot, William J.; Bock, Cathryn H.; Caporaso, Neil; Casey, Graham; Deming, Sandra L.; Diver, W. Ryan

    2014-01-01

    The extent of recent selection in admixed populations is currently an unresolved question. We scanned the genomes of 29,141 African Americans and failed to find any genome-wide-significant deviations in local ancestry, indicating no evidence of selection influencing ancestry after admixture. A recent analysis of data from 1,890 African Americans reported that there was evidence of selection in African Americans after their ancestors left Africa, both before and after admixture. Selection afte...

  13. Admixture analysis of stocked brown trout populations using mapped microsatellite DNA markers: indigenous trout persist in introgressed populations

    OpenAIRE

    Hansen, Michael M; Mensberg, Karen-Lise D.

    2009-01-01

    Admixture between wild and captive populations is an increasing concern in conservation biology. Understanding the extent of admixture and the processes involved requires identification of admixed and non-admixed individuals. This can be achieved by statistical methods employing Bayesian clustering, but resolution is low if genetic differentiation is weak. Here, we analyse stocked brown trout populations represented by historical (1943–1956) and contemporary (2000s) samples, where genetic dif...

  14. Stability investigation of total parenteral nutrition admixture prepared in a hospital pharmacy

    OpenAIRE

    Mirković Dušica; Antunović Mirjana; Putić Vesna; Aleksić Dragana

    2008-01-01

    Background/Aim. In the cases when nutrition of patients can not be orally nor enterally performed, parenteral nutrition is a method of the therapy that provides more successful and rapid recovery. In that way, hospitalization can be significantly shorter, healing costs reduced and mortality minimized. Total parenteral nutrition (TPN) admixtures are the most complex systems which contain amino acids, carbohydrates, lipid emulsion, macroelectrolytes (Na+, K+, Ca2+, Mg2+, Cl-, SO42-, PO43-), oli...

  15. Compatibility between base concrete made with different chemical admixtures and surface hardener

    OpenAIRE

    Pinheiro-Alves, M.ª Teresa; Sequeira, Ana Rita; Bettencourt Ribeiro, António

    2012-01-01

    Many cases of cracking and detachment of the concrete surface have appeared in concrete floors where surface hardeners were used in Portugal. The main causes for cracking and delamination of trowelled concrete pavements are several and it is essential to control bleeding and the time available to perform the finishing operations. Several base concretes were made with different chemical admixtures and one type of surface hardeners. The purpose of this study was evaluating the influence of the ...

  16. Quality assessment of total parenteral nutrition admixtures by the use of fractional factorial design

    Directory of Open Access Journals (Sweden)

    Mirković Dušica

    2013-01-01

    Full Text Available Background/Aim. Parenteral nutrition as a specific aspect of providing nutritients still remains a permanent topic of both theoretical and experimental research. Total parenteral nutrition (TPN admixtures have complex contents making difficult to maintain their stability. The most critical parameter is the diameter of a lipid droplet, i.e. droplet size distribution. It is recommended that droplet size should not be more than 5

  17. PREDICTION OF GLOBAL AND LOCAL SIMMENTAL AND RED HOLSTEIN FRIESIAN ADMIXTURE LEVELS IN SWISS FLECKVIEH CATTLE

    Directory of Open Access Journals (Sweden)

    Negar Khayatzadeh

    2015-09-01

    Full Text Available In this study we estimated levels of local ancestry for individuals of the Swiss Fleckvieh dairy cattle population. It is a composite breed descending from two pure breeds, Simmental (SIM and Red Holstein Friesian (RHF. Illumina BovineSNP50 Beadchip genotyping data for a total of 500 pure and admixed animals were used for the analysis. The global ancestries estimated by Hidden Markov model were 0.68 and 0.32 for RHF and SIM respectively. Local ancestry levels investigated along chromosomes 2, 3 and 13 indicated that there were some regions across the chromosomes exhibiting substantial fluctuations in admixture. On chromosome 2, in the range of 28 to 31, 41 to 46 and 54 to 56 Mb RHF ancestry is substantially higher than average (0.77-0.78. These regions on chromosome 2 are wide, indicating recent admixture. Along the segments on chromosome 2, many QTLs related to dairy, conformation, reproduction, health and carcass traits were found. We observed sharper excess in favour of SIM on chromosome 3, whereas different regions with excess of RHF and SIM were found out on Chromosome 13. At the first part of chromosome 13, an excess of RHF was observed. Moreover, in regions between 40 and 57 Mb excess of SIM, referred to recent admixture was detected. In respect of RHF chromosome segments in admixed animals, dairy, reproduction and health QTLs were found. In positions where more Simmental segments were detected, QTLs related to meat and carcass traits as well as udder health traits were found. In conclusion, the authors believe that estimation of local admixture levels in crossbred populations can add information to the composite breeds history of selection.

  18. Utilization of black liquor as concrete admixture and set retarder aid

    OpenAIRE

    Samar A. El-Mekkawi; Ibrahim M. Ismail; Mohammed M. El-Attar; Alaa A. Fahmy; Samia S. Mohammed

    2011-01-01

    The utilization of black liquor, produced by the pulp and paper industry in Egypt, as a workability aid and set retarder admixture has been investigated. This approach may help eliminate the environmentally polluting black liquor waste. It also provides a low cost by-product, which can be widely used in the construction industry. The properties of black liquor and its performance on concrete at two different ratios of water to cement have been studied. The results revealed that black liquor f...

  19. Semiconductor-metal transition in semiconductor melts with 3d metal admixtures

    International Nuclear Information System (INIS)

    Electrical conductivity and thermoelectric power measurements were performed for liquid semiconductor alloys Se0.5Te0.5 doped with 3d metals in a wide temperature range (up to 1600 K) under ambient pressures of argon gas (up to 30 MPa). Structure changes were studied by means of X-ray diffraction method. The 3d metal admixtures affect electrophysical properties and a temperature of the semiconductor-metal transition (SMT)

  20. Search for admixture of heavy neutrinos with masses between 5 and 55 keV

    OpenAIRE

    Markey, J.; Boehm, F.

    1985-01-01

    Using a magnetic spectrometer at a momentum resolution of 0.3%, we have studied the beta spectrum from 35S. We do not see evidence for the admixture of a heavy neutrino to the usual light (m~0) ν̃e accompanying beta decay, in the mass range between 5 and 50 keV, with a limit for the mixing strength of |U|2

  1. Profile of Intravenous Admixture Compatibility in the Intensive Care Unit (ICU) Patients

    OpenAIRE

    Sharly Dwijayanti; Sylvi Irawati; Eko Setiawan

    2016-01-01

    which may directly impact to the outcome of treatment to the Intensive Care Unit (ICU) patients. The objective of this study was to identify the profile of compatibility and incompatibility among IV admixtures given to the ICU patients. This observational research was conducted prospectively to the patients admitted in the ICU at a private hospital in Surabaya from October–December 2014. In this research, compatibility data of IV drug and its solution was compared with drug brochure and Handb...

  2. Lime-based repair mortars with water-repellent admixtures: laboratory durability assessment

    OpenAIRE

    Nunes, C.; Slížková, Z. (Zuzana)

    2015-01-01

    Conservation of architectural structures using lime binders is currently an important research topic aiming compatibility, durability and sustainability. In this study, lime (L) and lime-metakaolin (LM) mortars were prepared with the addition of water-repellent admixtures: linseed oil, stand oil and a silane based water-repellent. Experimental results demonstrate that oil imparts higher hydrophobicity to both L and LM mixtures. Durability was assessed through freeze-thaw and NaCl crystal...

  3. Intraspecific genetic admixture and the morphological diversification of an estuarine fish population complex.

    Science.gov (United States)

    Dodson, Julian J; Bourret, Audrey; Barrette, Marie France; Turgeon, Julie; Daigle, Gaétan; Legault, Michel; Lecomte, Frédéric

    2015-01-01

    The North-east American Rainbow smelt (Osmerus mordax) is composed of two glacial races first identified through the spatial distribution of two distinct mtDNA lineages. Contemporary breeding populations of smelt in the St. Lawrence estuary comprise contrasting mixtures of both lineages, suggesting that the two races came into secondary contact in this estuary. The overall objective of this study was to assess the role of intraspecific genetic admixture in the morphological diversification of the estuarine rainbow smelt population complex. The morphology of mixed-ancestry populations varied as a function of the relative contribution of the two races to estuarine populations, supporting the hypothesis of genetic admixture. Populations comprising both ancestral mtDNA races did not exhibit intermediate morphologies relative to pure populations but rather exhibited many traits that exceeded the parental trait values, consistent with the hypothesis of transgressive segregation. Evidence for genetic admixture at the level of the nuclear gene pool, however, provided only partial support for this hypothesis. Variation at nuclear AFLP markers revealed clear evidence of the two corresponding mtDNA glacial races. The admixture of the two races at the nuclear level is only pronounced in mixed-ancestry populations dominated by one of the mtDNA lineages, the same populations showing the greatest degree of morphological diversification and population structure. In contrast, mixed-ancestry populations dominated by the alternate mtDNA lineage showed little evidence of introgression of the nuclear genome, little morphological diversification and little contemporary population genetic structure. These results only partially support the hypothesis of transgressive segregation and may be the result of the differential effects of natural selection acting on admixed genomes from different sources. PMID:25856193

  4. Intraspecific Genetic Admixture and the Morphological Diversification of an Estuarine Fish Population Complex

    OpenAIRE

    Dodson, Julian J.; Bourret, Audrey; Barrette, Marie France; Turgeon, Julie; Daigle, Gaétan; Legault, Michel; Lecomte, Frédéric

    2015-01-01

    The North-east American Rainbow smelt (Osmerus mordax) is composed of two glacial races first identified through the spatial distribution of two distinct mtDNA lineages. Contemporary breeding populations of smelt in the St. Lawrence estuary comprise contrasting mixtures of both lineages, suggesting that the two races came into secondary contact in this estuary. The overall objective of this study was to assess the role of intraspecific genetic admixture in the morphological diversification of...

  5. Plant cover and water balance in gravel admixtures at an arid waste-burial site

    International Nuclear Information System (INIS)

    Isolation of radioactive waste buried in unsaturated zones will require long-term control of recharge and erosion. Soil covers control recharge at and sites by storing rainwater close enough to the surface to be removed by evapotranspiration. Surface layers of rock or gravel control erosion at sites with sparse vegetation, but can also alter plant habitat and cause recharge through interred waste. As an alternative, gravel mixed into the uppermost soil law may control erosion ever the king-term better than surface gravel layers. Gravel admixtures may also not influence plant establishment or sod water balance in waste-site covers. The interactive effects of gravel admixture concentration, vegetation, and precipitation on soil water content and plant cover were measured at the US Department of Energy's Hanford Site. Results support use of a combination of vegetation and gravel admixtures for erosion control. Vegetation seasonally depleted root zone water storage to about 6.5 volume % regardless of precipitation amount or the presence of gravel admixture amendments. In contrast, yearly increases in soil water storage as deep as 225 cm in plots without vegetation may be a leading indicator of recharge. The composition and abundance of vegetation changed over time and with precipitation amount, but was not influenced by gravel amendments. Seeded wheatgrasses [Agropyron sibericum Wilde and Agropyron dasystachyum (Hook.) Scribn.] established only when irrigated with twice average precipitation, but persisted after the irrigation ceased. Cheatgrass (Bromus tectorum L.) and Russian thistle (Salsola kali L.) colonized areas receiving both irrigation and ambient precipitation. Stands with wheatgrasses extracted water more rapidly and depleted soil water to lower levels than cheatgrass-dominated stands. Increases in gravel cover and near-surface gravel concentrations after 5 yr were evidence of the formation of a protective gravel veneer. 44 refs., 8 figs., 2 tabs

  6. Dissecting the genetic structure and admixture of four geographical Malay populations

    OpenAIRE

    Lian Deng; Boon-Peng Hoh; Dongsheng Lu; Woei-Yuh Saw; Rick Twee-Hee Ong; Anuradhani Kasturiratne; H Janaka de Silva; Bin Alwi Zilfalil; Norihiro Kato; Wickremasinghe, Ananda R; Yik-Ying Teo; Shuhua Xu

    2015-01-01

    The Malay people are an important ethnic composition in Southeast Asia, but their genetic make-up and population structure remain poorly studied. Here we conducted a genome-wide study of four geographical Malay populations: Peninsular Malaysian Malay (PMM), Singaporean Malay (SGM), Indonesian Malay (IDM) and Sri Lankan Malay (SLM). All the four Malay populations showed substantial admixture with multiple ancestries. We identified four major ancestral components in Malay populations: Austrones...

  7. Reduction in nitrate leaching from a concrete waste form by using waterproofing admixture additions

    International Nuclear Information System (INIS)

    Admixture additions of active lime and tricalcium aluminate reduced leach rate about 20% during a seven-day test of a concrete waste form containing a nitrate bearing, aqueous waste. CaO was 5% more effective and, in SEM examination, appeared to hydrate to CaOH which expanded in the concrete pores and blocked water movement. Over time, this compound appeared to dissolve slowly in the water, and the barrier layer it produced slowly receded into the specimen interior

  8. Age of First Suicide Attempt in Men and Women: An Admixture Analysis

    OpenAIRE

    Hilario Blasco-Fontecilla; Alegria, Analucia A; David Delgado-Gomez; Teresa Legido-Gil; Jeronimo Saiz-Ruiz; Oquendo, Maria A; Enrique Baca-Garcia

    2012-01-01

    Objectives. To define different subgroups of suicide attempters according to age at onset of suicide attempts. Methods. Participants were 229 suicide attempters (147 females; 82 males) admitted to a general hospital in Madrid, Spain. We used admixture analysis to determine the best-fitting model for the age at onset of suicide attempts separated by sex. Results. The best fitted model for the age at onset of suicide attempts was a mixture of two gaussian distributions. Females showed an earlie...

  9. Properties of low drying-shrinkage concrete with shrinkage-reducing admixture

    International Nuclear Information System (INIS)

    Effects on drying shrinkage of concrete were tested by using cement, the limestone coarse aggregate and the shrinkage-reducing admixture. As the results, the drying shrinkage of concrete was realized below 400x10-6. By using this low drying-shrinkage concrete, to prevent cracking on concrete structure during the long service life and to secure the measuring accuracy of concrete structure related the accelerator are expected. (author)

  10. Tracing the origin of the east-west population admixture in the Altai region (Central Asia.

    Directory of Open Access Journals (Sweden)

    Mercedes González-Ruiz

    Full Text Available A recent discovery of Iron Age burials (Pazyryk culture in the Altai Mountains of Mongolia may shed light on the mode and tempo of the generation of the current genetic east-west population admixture in Central Asia. Studies on ancient mitochondrial DNA of this region suggest that the Altai Mountains played the role of a geographical barrier between West and East Eurasian lineages until the beginning of the Iron Age. After the 7th century BC, coinciding with Scythian expansion across the Eurasian steppes, a gradual influx of East Eurasian sequences in Western steppes is detected. However, the underlying events behind the genetic admixture in Altai during the Iron Age are still unresolved: 1 whether it was a result of migratory events (eastward firstly, westward secondly, or 2 whether it was a result of a local demographic expansion in a 'contact zone' between European and East Asian people. In the present work, we analyzed the mitochondrial DNA lineages in human remains from Bronze and Iron Age burials of Mongolian Altai. Here we present support to the hypothesis that the gene pool of Iron Age inhabitants of Mongolian Altai was similar to that of western Iron Age Altaians (Russia and Kazakhstan. Thus, this people not only shared the same culture (Pazyryk, but also shared the same genetic east-west population admixture. In turn, Pazyryks appear to have a similar gene pool that current Altaians. Our results further show that Iron Age Altaians displayed mitochondrial lineages already present around Altai region before the Iron Age. This would provide support for a demographic expansion of local people of Altai instead of westward or eastward migratory events, as the demographic event behind the high population genetic admixture and diversity in Central Asia.

  11. Chemical stability of an admixture combining ziconotide and bupivacaine during simulated intrathecal administration.

    Science.gov (United States)

    Shields, David; Montenegro, Rick; Aclan, Jennifer

    2007-10-01

    Objective.  To determine the stability of an admixture combining ziconotide with bupivacaine hydrochloride during simulated intrathecal infusion under laboratory conditions at 37°. Materials and Methods.  An admixture containing ziconotide (25 µg/mL) and bupivacaine hydrochloride (5 mg/mL) was stored in SynchroMed® II pumps at 37° and in control vials at either 37° or 5°. Using high-performance liquid chromatography, drug concentrations were determined from samples obtained at varying intervals during the 30-day study. Results.  After 30 days, pump ziconotide and bupivacaine hydrochloride concentrations measured an average of 86.9% and 99.4% of their initial concentrations, respectively. Control vials displayed similar degradation rates for both drugs. Statistical evaluation of the ziconotide 95% confidence interval indicated that the ziconotide concentration would meet or exceed 90% and 80% of initial concentration for 22 days and 45 days, respectively. Conclusions.  An admixture containing 25 µg/mL ziconotide and 5 mg/mL bupivacaine hydrochloride was 90% stable for 22 days and 80% stable for 45 days (extrapolated) in SynchroMed® II infusion pumps. PMID:22150945

  12. Rate of decay in admixture linkage disequilibrium and its implication in gene mapping

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Modeling linkage disequilibria (LD) between genes usually observed in admixed natural populations has been shown an effective approach in high-resolution mapping of disease genes in humans. A prerequisite to obtain accurate estimation of recombination fraction between genes at a marker locus and the disease locus using the approach is a reliable prediction of the proportion of the admixture populations. The present study suggested the use of gene frequencies to predict the estimate of the admixture propor-tion based on the observation that the gene frequencies are much more stable quantities than the haplotype frequencies over evolution of the population. In this paper, we advanced the theory and methods by which the decay rate of nonlinear term of LD in admixed population may be used to estimate the recombination fraction between the genes. Theoretical analysis and simulation study indicate that, the larger the difference of gene frequencies between parental populations and the more closely the admixture proportion approaches 0.5, the more important the nonlinear term of the LD in the admixed population, and hence the more informative such admixed populations in the high-resolution gene mapping practice.

  13. Effect of Chemical Admixtures on the Engineering Properties of Tropical Peat Soils

    Directory of Open Access Journals (Sweden)

    Bujang B.K. Huat

    2005-01-01

    Full Text Available This research describes a study on the effect of chemical (cement and lime admixtures on the index and engineering properties (compaction and unconfined strength of tropical peat soils. The ordinary Portland cement and hydrated lime were used. The amounts cement and lime added to the peat soil sample, as a percentage of the dry soil mass was in the range of 5-15% and 5-25%, respectively. The results of the study show that the addition of the chemical admixture, cement and lime, can improve the engineering properties of tropical peat soils. The soil liquid limit is found to decrease with an increase in the cement and lime content. The soil maximum dry density is found to increase while the optimum water content is found to decrease with an increase in the cement and lime content. The unconfined compressive strength of the soil is found to increase significantly with increase in cement and lime content, especially after a long curing period. However it is also found that higher organic content of the soil negate the positive effect of the cement and lime in altering (improving the mechanical properties of the soil. When comparing the performance of the cement and lime as a chemical admixture for the tropical peat soil, the ordinary Portland cement appears to perform better than the hydrated lime.

  14. Effects of lithium nitrate admixture on early-age cement hydration

    International Nuclear Information System (INIS)

    Although the benefits of lithium admixtures for mitigation of alkali-silica reaction (ASR) have been well documented, the potential ancillary effects of lithium compounds on cement and concrete remain largely uncharacterized. To examine the effects of the most common lithium admixture - lithium nitrate - on early-age behavior, the admixture was introduced at dosages of 0% to 400% of the recommended dosage to six cements of varying composition and to a cement-fly ash blend. Behavior was examined by isothermal calorimetry and measurements of chemical shrinkage, autogenous shrinkage, and setting time. Results indicate that lithium nitrate accelerates the early hydration of most cements but may retard hydration after 24 h. In the lowest alkali cement tested, set times were shortened in the presence of lithium nitrate by 15-22%. Higher dosages appeared to increase autogenous shrinkage after 40 days. The replacement of cement by Class F fly ash at 20% by weight appeared to diminish the early acceleration effects, but later hydration retardation and autogenous shrinkage were still observed

  15. Study on Strength and Microstructure of Cement-Based Materials Containing Combination Mineral Admixtures

    Directory of Open Access Journals (Sweden)

    Meijuan Rao

    2016-01-01

    Full Text Available The compressive strength of complex binders containing two or three blended mineral admixtures in terms of glass powder (GP, limestone powder (LP, and steel slag powder (SP was determined by a battery solution type compressive testing machine. The morphology and microstructure characteristics of complex binder hydration products were also studied by microscopic analysis methods, such as XRD, TG-DTA, and SEM. The mechanical properties of the cement-based materials were analyzed to reveal the most appropriate mineral admixture type and content. The early sample strength development with GP was very slow, but it rapidly grew at later stages. The micro aggregate effect and pozzolanic reaction mutually occurred in the mineral admixture. In the early stage, the micro aggregate effect reduced paste porosity and the small particles connected with the cement hydration products to enhance its strength. In the later stage, the pozzolanic reaction of some components in the complex powder occurred and consumed part of the calcium hydroxide to form C-S-H gel, thus improving the hydration environment. Also, the produced C-S-H gel made the structure more compact, which improved the structure’s strength.

  16. Chemical stability of ziconotide-clonidine hydrochloride admixtures with and without morphine sulfate during simulated intrathecal administration.

    Science.gov (United States)

    Shields, David; Montenegro, Rick

    2007-10-01

    Objective.  To determine the stability of ziconotide-clonidine hydrochloride admixtures with and without morphine sulfate during simulated intrathecal infusion under laboratory conditions at 37°. Materials and Methods.  Admixtures of ziconotide (25 µg/mL) and clonidine hydrochloride (2 mg/mL) with and without morphine sulfate (35 mg/mL) were stored in Medtronic SynchroMed® II pumps at 37°. Pumps were sampled immediately after filling and at four additional time points over the course of 28 (ziconotide-clonidine hydrochloride admixture) or 20 (ziconotide-clonidine hydrochloride-morphine sulfate admixture) days. Drug concentrations were determined using high-performance liquid chromatography. Results.  Ziconotide concentration exceeded 97% of initial at all time points when combined with clonidine alone; statistical evaluation indicated that both ziconotide and clonidine concentrations would remain above 90% of initial for more than 60 days. When compounded with both clonidine and morphine, ziconotide and clonidine concentrations declined; statistical evaluation indicated that the ziconotide concentration was 70% of initial after 20 days, and that clonidine would remain 90% stable for 42 days. Morphine was stable in the presence of ziconotide and clonidine. Conclusions.  A ziconotide-clonidine admixture was 90% stable for 60 days (extrapolated), and a ziconotide-clonidine-morphine admixture was 70% stable for 20 days. PMID:22150946

  17. Chemical, Mechanical, and Durability Properties of Concrete with Local Mineral Admixtures under Sulfate Environment in Northwest China

    Directory of Open Access Journals (Sweden)

    Qingke Nie

    2014-05-01

    Full Text Available Over the vast Northwest China, arid desert contains high concentrations of sulfate, chloride, and other chemicals in the ground water, which poses serious challenges to infrastructure construction that routinely utilizes portland cement concrete. Rapid industrialization in the region has been generating huge amounts of mineral admixtures, such as fly ash and slags from energy and metallurgical industries. These industrial by-products would turn into waste materials if not utilized in time. The present study evaluated the suitability of utilizing local mineral admixtures in significant quantities for producing quality concrete mixtures that can withstand the harsh chemical environment without compromising the essential mechanical properties. Comprehensive chemical, mechanical, and durability tests were conducted in the laboratory to characterize the properties of the local cementitious mineral admixtures, cement mortar and portland cement concrete mixtures containing these admixtures. The results from this study indicated that the sulfate resistance of concrete was effectively improved by adding local class F fly ash and slag, or by applying sulfate resistance cement to the mixtures. It is noteworthy that concrete containing local mineral admixtures exhibited much lower permeability (in terms of chloride ion penetration than ordinary portland cement concrete while retaining the same mechanical properties; whereas concrete mixtures made with sulfate resistance cement had significantly reduced strength and much increased chloride penetration comparing to the other mixtures. Hence, the use of local mineral admixtures in Northwest China in concrete mixtures would be beneficial to the performance of concrete, as well as to the protection of environment.

  18. Debris entrainment and landform genesis during tidewater glacier surges

    Science.gov (United States)

    Lovell, Harold; Fleming, Edward J.; Benn, Douglas I.; Hubbard, Bryn; Lukas, Sven; Rea, Brice R.; Noormets, Riko; Flink, Anne E.

    2015-08-01

    The englacial entrainment of basal debris during surges presents an opportunity to investigate processes acting at the glacier bed. The subsequent melt-out of debris-rich englacial structures during the quiescent phase produces geometrical ridge networks on glacier forelands that are diagnostic of surge activity. We investigate the link between debris entrainment and proglacial geomorphology by analyzing basal ice, englacial structures, and ridge networks exposed at the margins of Tunabreen, a tidewater surge-type glacier in Svalbard. The basal ice facies display clear evidence for brittle and ductile tectonic deformation, resulting in overall thickening of the basal ice sequence. The formation of debris-poor dispersed facies ice is the result of strain-induced metamorphism of meteoric ice near the bed. Debris-rich englacial structures display a variety of characteristics and morphologies and are interpreted to represent the incorporation and elevation of subglacial till via the squeezing of till into basal crevasses and hydrofracture exploitation of thrust faults, reoriented crevasse squeezes, and preexisting fractures. These structures are observed to melt-out and form embryonic geometrical ridge networks at the base of a terrestrially grounded ice cliff. Ridge networks are also located at the terrestrial margins of Tunabreen, neighboring Von Postbreen, and in a submarine position within Tempelfjorden. Analysis of network characteristics allows these ridges to be linked to different formational mechanisms of their parent debris-rich englacial structures. This in turn provides an insight into variations in the dominant tectonic stress regimes acting across the glacier during surges.

  19. Admixture mapping of end stage kidney disease genetic susceptibility using estimated mutual information ancestry informative markers

    Directory of Open Access Journals (Sweden)

    Geiger Dan

    2010-10-01

    Full Text Available Abstract Background The question of a genetic contribution to the higher prevalence and incidence of end stage kidney disease (ESKD among African Americans (AA remained unresolved, until recent findings using admixture mapping pointed to the association of a genomic locus on chromosome 22 with this disease phenotype. In the current study we utilize this example to demonstrate the utility of applying a multi-step admixture mapping approach. Methods A multi-step case only admixture mapping study, consisted of the following steps was designed: 1 Assembly of the sample dataset (ESKD AA; 2 Design of the estimated mutual information ancestry informative markers (n = 2016 screening panel 3; Genotyping the sample set whose size was determined by a power analysis (n = 576 appropriate for the initial screening panel; 4 Inference of local ancestry for each individual and identification of regions with increased AA ancestry using two different ancestry inference statistical approaches; 5 Enrichment of the initial screening panel; 6 Power analysis of the enriched panel 7 Genotyping of additional samples. 8 Re-analysis of the genotyping results to identify a genetic risk locus. Results The initial screening phase yielded a significant peak using the ADMIXMAP ancestry inference program applying case only statistics. Subgroup analysis of 299 ESKD patients with no history of diabetes yielded peaks using both the ANCESTRYMAP and ADMIXMAP ancestry inference programs. The significant peak was found on chromosome 22. Genotyping of additional ancestry informative markers on chromosome 22 that took into account linkage disequilibrium in the ancestral populations, and the addition of samples increased the statistical significance of the finding. Conclusions A multi-step admixture mapping analysis of AA ESKD patients replicated the finding of a candidate risk locus on chromosome 22, contributing to the heightened susceptibility of African Americans to develop non

  20. Combined air and water pollution control system

    Science.gov (United States)

    Wolverton, Billy C. (Inventor); Jarrell, Lamont (Inventor)

    1990-01-01

    A bioaquatic air pollution control system for controlling both water and atmospheric pollution is disclosed. The pollution control system includes an exhaust for directing polluted gases out of a furnace and a fluid circulating system which circulates fluid, such as waste water, from a source, past the furnace where the fluid flow entrains the pollutants from the furnace. The combined fluid and pollutants are then directed through a rock/plant/microbial filtering system. A suction pump pumps the treated waste water from the filter system past the exhaust to again entrain more pollutants from the furnace where they are combined with the fluid (waste water) and directed to the filter system.

  1. The importance of entrainment and bulking on debris flow runout modeling: examples from the Swiss Alps

    Science.gov (United States)

    Frank, F.; McArdell, B. W.; Huggel, C.; Vieli, A.

    2015-11-01

    This study describes an investigation of channel-bed entrainment of sediment by debris flows. An entrainment model, developed using field data from debris flows at the Illgraben catchment, Switzerland, was incorporated into the existing RAMMS debris-flow model, which solves the 2-D shallow-water equations for granular flows. In the entrainment model, an empirical relationship between maximum shear stress and measured erosion is used to determine the maximum potential erosion depth. Additionally, the average rate of erosion, measured at the same field site, is used to constrain the erosion rate. The model predicts plausible erosion values in comparison with field data from highly erosive debris flow events at the Spreitgraben torrent channel, Switzerland in 2010, without any adjustment to the coefficients in the entrainment model. We find that by including bulking due to entrainment (e.g., by channel erosion) in runout models a more realistic flow pattern is produced than in simulations where entrainment is not included. In detail, simulations without entrainment show more lateral outflow from the channel where it has not been observed in the field. Therefore the entrainment model may be especially useful for practical applications such as hazard analysis and mapping, as well as scientific case studies of erosive debris flows.

  2. An applied model for the height of the daytime mixed layer and the entrainment zone

    DEFF Research Database (Denmark)

    Batchvarova, E.; Gryning, Sven-Erik

    1994-01-01

    A model is presented for the height of the mixed layer and the depth of the entrainment zone under near-neutral and unstable atmospheric conditions. It is based on the zero-order mixed layer height model of Batchvarova and Gryning (1991) and the parameterization of the entrainment zone depth prop...

  3. Bubble-type gas entrainment into liquid from free surface by vortex

    International Nuclear Information System (INIS)

    A gas entrainment rate into liquid by a vortex formed on the free surface was examined experimentally. Water flowed into a cylindrical vessel from a wall tangentially. Swirl flow was formed in the vessel, and then water left from the bottom outlet of the vessel. The flow state of the entrainment was visually observed by using a high speed video camera. The gas entrainment rate into water was measured. A stable vortex was formed in the test vessel. When the flow velocity; the velocity at the bottom outlet, was low, a single bubble was periodically torn off from the bottom tip of the vortex and the bubble-type gas entrainment was observed. As the flow rate was increased, the bottom tip of the vortex penetrated into the outlet pipe and the bubble-type gas entrainment continued. A further increase in the flow velocity resulted in the transition from the bubble-type gas entrainment to the vortex-type gas entrainment and the gas entrainment rate considerably increased with the flow velocity. After the vortex tip penetrated into the outlet pipe, the rotation speed of the vortex decayed. As a result of it, the Kelvin-Helmholtz instability wave length got long and the size of the generated bubble became large. Then, the outlet pipe was filled with the large bubbles and the flow state in the outlet pipe turned to the slug/churn flow and a large amount of gas began to be carried out form the test vessel. (author)

  4. Determination of human EEG alpha entrainment ERD/ERS using the continuous complex wavelet transform

    Science.gov (United States)

    Chorlian, David B.; Porjesz, Bernice; Begleiter, Henri

    2003-04-01

    Alpha entrainment caused by exposure to a background stimulus continuously flickering at a rate of 8 1/3 Hz was affected by the appearance of a foreground target stimulus to which the subjects were requested to press a button. With the use of bipolar derivations (to reduce volume conduction effects), scalp recorded EEG potentials were subjected to a continuous wavelet transform using complex Morlet wavelets at a range of scales. Complex Morlet wavelets were used to calculate efficiently instantaneous amplitudes and phases on a per-trial basis, rather than using the Hilbert transform on band-pass filtered data. Multiple scales were employed to contrast the pattern of alpha activity with those in other bands, and to determine whether the harmonics observed in the spectral analysis of the data were simply a result of the non-sinusoidal response to the entraining signal or a distinct neural phenomenon. We were thus able to calculate desynchronization/resynchronization for both the entrained and non-entrained alpha activity. The occurance of the target stimulus caused a sharp increase in amplitude in both the entrained and non-entrained alpha activity, followed by a sharp decrease, and then a return to baseline, over a period of 2.5 seconds. However, the entrained alpha activity showed a much more rapid recovery than non-entrained activity.

  5. Application of high-precision numerical simulation method to quantitative evaluation of gas entrainment phenomena

    International Nuclear Information System (INIS)

    In the design study of the large-scale sodium-cooled fast reactor in Japan (JSFR), gas entrainment (GE) phenomena have to be evaluated in terms of their occurrences because entrained bubbles in the primary cooling system may cause disturbances in reactor power. Therefore, the authors have developed a prediction method for the GE occurrences and obtained conservative criteria in terms of the GE onset conditions. However, in a reasonable JSFR design, a small amount of entrained as may be allowed because there are always small deposition bubbles in the primary cooling system. In this case, not only the GE occurrences but also the amount of the entrained gas should be evaluated accurately. Therefore, the authors are studying the amount of the entrained gas by utilizing simple an experiment and a numerical simulation. In this paper, as a part of the validation of the numerical simulation method for the evaluation of the entrained gas flow rate, parametric simulations of the simple experiment are performed with a high-precision volume-of-fluid algorithm which simulate interfacial dynamic deformations directly. As a result, the simulation results gives larger entrained gas flow rate than the experimental data but the dependency of the entrained gas flow rate on the liquid flow rate is reproduced qualitatively. (author)

  6. LIDAR OBSERVATIONS OF MIXED LAYER DYNAMICS: TESTS OF PARAMETERIZED ENTRAINMENT MODELS OF MIXED LAYER GROWTH RATE

    Science.gov (United States)

    Lidar measurements of the atmospheric boundary layer height, the entrainment zone, wind speed and direction, ancillary temperature profiles and surface flux data were used to test current parameterized entrainment models of mixed layer growth rate. Six case studies under clear ai...

  7. Impurity effect on thermo-emf of phonon entrainment in metals

    International Nuclear Information System (INIS)

    Impact of electrons inelastic scattering on impurities on thermo-emf entrainment in metals is studied. It is shown that by low temperatures such processes make the basic contribution in thermo-emf suppression by impurities introduction. Along with the impurities concentration the addition to the entrainment thermo-emf, caused by inelastic scattering processes contains the great multiplier QD/T

  8. Emissions from vehicles, tailpipe and vehicle re-entrained road dust

    Science.gov (United States)

    Zhu, Dongzi

    Emissions from transportation are some of the largest sources of urban air pollution. Transportation emissions originate from both the engine-through combustion processes and non-tailpipe re-suspended road dust emissions induced by vehicle travel on unpaved and paved roads. Gaseous and particulate emissions from transportation sources have negative impacts on human health, visibility and may influence the global radiation balance. Fugitive dust emissions originating from vehicle travel on paved and unpaved roads constitute a significant fraction of the PM10 in many areas of the western US impacting their attainment status of National Ambient Air Quality Standards. The research used three novel instrument platforms developed at the Desert Research Institute. The In-Plume Emissions Test Stand (IPETS) was designed to provide characterization of exhaust emissions from in-use individual vehicles or engines by analyzing air as close as 1 m from the exhaust port. Real-world emission factors can be quantified by in-plume measurements and provide more realistic measures for emission inventories, source modeling, and receptor modeling than certification measurements. The Testing Re-entrained Aerosol Kinetic Emissions from Roads (TRAKER) provides an effective alternate approach to the EPA AP-42 road dust emissions estimation techniques by sampling 1000s of km of roads versus isolated 3 m sections. The Portable Deposition Monitoring Platform (PDMP incorporates PM and meteorological instruments to characterize the downwind change in particle concentrations to define depositional losses in different environments. The research outcome provides important knowledge for understanding diesel engine emissions, road dust emissions and aerosol deposition process near road sources.

  9. Entrainment of Dungeness Crab in the Desdemona Shoals Reach of the Lower Columbia River Navigation Channel

    Energy Technology Data Exchange (ETDEWEB)

    Pearson, Walter H.; Kohn, Nancy P.; Skalski, J. R.

    2006-09-30

    Proposed dredging of the Columbia River has raised concerns about related impacts on Dungeness crab in the Columbia River Estuary (CRE). This study follows two major efforts, sponsored by the Portland District of the U. S. Army Corps of Engineers (USACE) to quantify the number of crabs entrained by a hopper dredge working in the CRE. From June 2002 through September 2002, Pacific Northwest National Laboratory (PNNL) conducted direct measurements of crab entrainment in the CRE from the mouth of the Columbia River (MCR, river mile -3 to +3) upriver as far as Miller Sands (river mile 21 to 24). These studies constituted a major step in quantifying crab entrainment in the CRE, and allowed statistically bounded projections of adult equivalent loss (AEL) for Dungeness crab populations under a range of future construction dredging and maintenance dredging scenarios (Pearson et al. 2002, 2003). In 2004, PNNL performed additional measurements to improve estimates of crab entrainment at Desdemona Shoals and at Flavel Bar, a reach near Astoria that had not been adequately sampled in 2002 (Figure 1). The 2004 data were used to update the crab loss projections for channel construction to 43 ft MLLW. In addition, a correlation between bottom salinity and adult (age 2+ and 3+, >100 mm carapace width) crab entrainment was developed using 2002 data, and elaborated upon with the 2004 data. This crab salinity model was applied to forecasting seasonal (monthly) entrainment rates and AEL using seasonal variations in salinity (Pearson et al. 2005). In the previous studies, entrainment rates in Desdemona Shoals were more variable than in any of the other reaches. Pearson et al. (2005) concluded that ?the dynamics behind the variable entrainment rates at Desdemona Shoals are not fully understood,? as well as finding that juvenile crab entrainment was not significantly correlated with salinity as it was for older crab. The present study was undertaken to address the question of whether the

  10. Phase-selective entrainment of nonlinear oscillator ensembles

    Science.gov (United States)

    Zlotnik, Anatoly; Nagao, Raphael; Kiss, István Z.; Li-Shin, Jr.

    2016-03-01

    The ability to organize and finely manipulate the hierarchy and timing of dynamic processes is important for understanding and influencing brain functions, sleep and metabolic cycles, and many other natural phenomena. However, establishing spatiotemporal structures in biological oscillator ensembles is a challenging task that requires controlling large collections of complex nonlinear dynamical units. In this report, we present a method to design entrainment signals that create stable phase patterns in ensembles of heterogeneous nonlinear oscillators without using state feedback information. We demonstrate the approach using experiments with electrochemical reactions on multielectrode arrays, in which we selectively assign ensemble subgroups into spatiotemporal patterns with multiple phase clusters. The experimentally confirmed mechanism elucidates the connection between the phases and natural frequencies of a collection of dynamical elements, the spatial and temporal information that is encoded within this ensemble, and how external signals can be used to retrieve this information.

  11. Entrainment of heterogeneous glycolytic oscillations in single cells

    CERN Document Server

    Gustavsson, A -K; Mehlig, B; Goksör, M

    2015-01-01

    Cell signaling, gene expression, and metabolism are affected by cell-cell heterogeneity and random changes in the environment. The effects of such fluctuations on cell signaling and gene expression have recently been studied intensively using single-cell experiments. In metabolism heterogeneity may be particularly important because it may affect synchronisation of metabolic oscillations, an important example of cell-cell communication. This synchronisation is notoriously difficult to describe theoretically as the example of glycolytic oscillations shows: neither is the mechanism of glycolytic synchronisation understood nor the role of cell-cell heterogeneity. To pin down the mechanism and to assess its robustness and universality we have experimentally investigated the entrainment of glycolytic oscillations in individual yeast cells by periodic external perturbations. We find that oscillatory cells synchronise through phase shifts and that the mechanism is insensitive to cell heterogeneity (robustness) and si...

  12. Turbulent mixing and entrainment in a gravity current

    Energy Technology Data Exchange (ETDEWEB)

    Ecke, Robert E [Los Alamos National Laboratory; Odier, Philippe [ENS-LYON, FRANCE; Chen, Jun [PURDUE UNIV.

    2010-01-01

    We present an experimental study of the mixing processes in a gravity current. The turbulent transport of momentum and buoyancy can be described in a very direct and compact form by a Prandtl mixing length model: the turbulent vertical fluxes of momentum and buoyancy are found to scale quadratically with the vertical mean gradients of velocity and density. The scaling coefficient is the square of the mixing lenth, approximately constant over the mixing zone of the stratified shear layer. We show how, in different flow configurations, this length can be related to the shear length of the flow ({var_epsilon}/{partial_derivative}{sub z}u{sup 3}){sup 1/2}. We also study the fluctuations of the momentum and density turbulent fluxes, showing how they relate to the mixing phenomena, and to the entrainment/detrainment balance.

  13. Spontaneous tempo and rhythmic entrainment in a bonobo (Pan paniscus).

    Science.gov (United States)

    Large, Edward W; Gray, Patricia M

    2015-11-01

    The emergence of speech and music in the human species represent major evolutionary transitions that enabled the use of complex, temporally structured acoustic signals to coordinate social interaction. While the fundamental capacity for temporal coordination with complex acoustic signals has been shown in a few distantly related species, the extent to which nonhuman primates exhibit sensitivity to auditory rhythms remains controversial. In Experiment 1, we assessed spontaneous motor tempo and tempo matching in a bonobo (Pan paniscus), in the context of a social drumming interaction. In Experiment 2, the bonobo spontaneously entrained and synchronized her drum strikes within a range around her spontaneous motor tempo. Our results are consistent with the hypothesis that the evolution of acoustic communication builds upon fundamental neurodynamic mechanisms that can be found in a wide range of species, and are recruited for social interactions. PMID:26147705

  14. Near-field entrainment in black smoker plumes

    Science.gov (United States)

    Smith, J. E.; Germanovich, L. N.; Lowell, R. P.

    2013-12-01

    In this work, we study the entrainment rate of the ambient fluid into a plume in the extreme conditions of hydrothermal venting at ocean floor depths that would be difficult to reproduce in the laboratory. Specifically, we investigate the flow regime in the lower parts of three black smoker plumes in the Main Endeavour Field on the Juan de Fuca Ridge discharging at temperatures of 249°C, 333°C, and 336°C and a pressure of 21 MPa. Such flow conditions are typical for ocean floor hydrothermal venting but would be difficult to reproduce in the laboratory. The centerline temperature was measured at several heights in the plume above the orifice. Using a previously developed turbine flow meter, we also measured the mean flow velocity at the orifice. Measurements were conducted during dives 4452 and 4518 on the submersible Alvin. Using these measurements, we obtained a range of 0.064 - 0.068 for values of the entrainment coefficient α, which is assumed constant near the orifice. This is half the value of α ≈ 0.12 - 0.13 that would be expected for plume flow regimes based on the existing laboratory results and field measurements in lower temperature and pressure conditions. In fact, α = 0.064 - 0.068 is even smaller than the value of α ≈ 0.075 characteristic of jet flow regimes and appears to be the lowest reported in the literature. Assuming that the mean value α = 0.066 is typical for hydrothermal venting at ocean floor depths, we then characterized the flow regimes of 63 black smoker plumes located on the Endeavor Segment of the Juan de Fuca Ridge. Work with the obtained data is ongoing, but current results indicate that approximately half of these black smokers are lazy in the sense that their plumes exhibit momentum deficits compared to the pure plume flow that develops as the plume rises. The remaining half produces forced plumes that show the momentum excess compared to the pure plumes. The lower value of the entrainment coefficient has important

  15. Experimental study of near-field entrainment of moderately overpressured jets

    Science.gov (United States)

    Solovitz, S.A.; Mastin, L.G.; Saffaraval, F.

    2011-01-01

    Particle image velocimetry (PIV) experiments have been conducted to study the velocity flow fields in the developing flow region of high-speed jets. These velocity distributions were examined to determine the entrained mass flow over a range of geometric and flow conditions, including overpressured cases up to an overpressure ratio of 2.83. In the region near the jet exit, all measured flows exhibited the same entrainment up until the location of the first shock when overpressured. Beyond this location, the entrainment was reduced with increasing overpressure ratio, falling to approximately 60 of the magnitudes seen when subsonic. Since entrainment ratios based on lower speed, subsonic results are typically used in one-dimensional volcanological models of plume development, the current analytical methods will underestimate the likelihood of column collapse. In addition, the concept of the entrainment ratio normalization is examined in detail, as several key assumptions in this methodology do not apply when overpressured.

  16. Droplet behavior analysis in consideration of droplet entrainment from liquid film in annular dispersed flow

    International Nuclear Information System (INIS)

    A method of droplet behavior simulation in an annular dispersed flow has been developed. In this method, both droplet deposition and entrainment from liquid film are considered. The Lagrangian method and stochastic model are used to analyze droplet diffusion and deposition behavior in a turbulent flow, and droplet entrainment from liquid film is calculated by an entrainment correlation. For the verification of this method, Gill's experiment is analyzed, in which the transition from annular flow with no entrainment to equilibrium annular dispersed flow was observed. Analysis results can also show the similar transition tendency. The experimental results of radial distribution of droplet mass flux are compared with analysis results. The agreement is good for low liquid flow rate, but entrainment rate must be adjusted for high liquid flow rate, in which gas turbulence is thought to be modified by high droplet density. In future work the effect of high droplet density on turbulence should be considered. (author)

  17. Re-entrainment of {sup 239}PuO{sub 2} Particles Captured on HEPA Filter Fibres

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, Y.; Koizumi, A.; Miyamoto, K

    1999-07-01

    Filter performance is very important not only before use but also in use. In addition to particle collection, particle retention or dispersion rate should be evaluated. Re-entrainment of {sup 239}PuO{sub 2} particles collected on HEPA filter fibres was investigated under various conditions of air flow direction, air flow rate, air flow pattern and dust loading. Plutonium aerosols with an activity median aerodynamic diameter of 0.45 {mu}m and a geometric standard deviation of 2.0 were used. Dispersion rate per hour, which is defined as activity ratio on the sampling filter downstream to that on the source filter, under forward flow, was measured as less than 2.3 x 10{sup -7} h{sup -1}. Under reverse flow, higher dispersion rates were observed, but the dispersion decreased with repeated sample runs. A high air flow rate increased the dispersion rate. There was no significant differences among air flow patterns. Dispersion rate depended strongly on the dust loading level. For example, at 2.9 times the loading of atmospheric aerosols compared with the initial pressure drop the dispersion rate was increased by approximately 100 times to 10{sup -2} h{sup -1}. (author)

  18. The performative pleasure of imprecision: a diachronic study of entrainment in music performance

    Directory of Open Access Journals (Sweden)

    Andrew eGeeves

    2014-10-01

    Full Text Available This study focuses in on a moment of live performance in which the entrainment amongst a musical quartet is threatened. Entrainment is asymmetric in so far as there is an ensemble leader who improvises and expands the structure of a last chorus of a piece of music beyond the limits tacitly negotiated during prior rehearsals and performances. Despite the risk of entrainment being disturbed and performance interrupted, the other three musicians in the quartet follow the leading performer and smoothly transition into unprecedented performance territory. We use this moment of live performance to work back through the fieldwork data, building a diachronic study of the development and bases of entrainment in live music performance. We introduce the concept of entrainment and profile previous theory and research relevant to entrainment in music performance. After outlining our methodology, we trace the evolution of the structure of the piece of music from first rehearsal to final performance. Using video clip analysis, interviews and field notes we consider how entrainment shaped and was shaped by the moment of performance in focus. The sense of trust between quartet musicians is established through entrainment processes, is consolidated via smooth adaptation to the threats of disruption. Nonverbal communicative exchanges, via eye contact, gesture and spatial proximity, sustain entrainment through phase shifts occurring swiftly and on the fly in performance contexts. These exchanges permit smooth adaptation promoting trust. This frees the quartet members to play with the potential disturbance of equilibrium inherent in entrained relationships and to play with this tension in an improvisatory way that enhances audience engagement and the live quality of performance.

  19. The performative pleasure of imprecision: a diachronic study of entrainment in music performance.

    Science.gov (United States)

    Geeves, Andrew; McIlwain, Doris J; Sutton, John

    2014-01-01

    This study focuses in on a moment of live performance in which the entrainment amongst a musical quartet is threatened. Entrainment is asymmetric in so far as there is an ensemble leader who improvises and expands the structure of a last chorus of a piece of music beyond the limits tacitly negotiated during prior rehearsals and performances. Despite the risk of entrainment being disturbed and performance interrupted, the other three musicians in the quartet follow the leading performer and smoothly transition into unprecedented performance territory. We use this moment of live performance to work back through the fieldwork data, building a diachronic study of the development and bases of entrainment in live music performance. We introduce the concept of entrainment and profile previous theory and research relevant to entrainment in music performance. After outlining our methodology, we trace the evolution of the structure of the piece of music from first rehearsal to final performance. Using video clip analysis, interviews and field notes we consider how entrainment shaped and was shaped by the moment of performance in focus. The sense of trust between quartet musicians is established through entrainment processes, is consolidated via smooth adaptation to the threats of disruption. Non-verbal communicative exchanges, via eye contact, gesture, and spatial proximity, sustain entrainment through phase shifts occurring swiftly and on the fly in performance contexts. These exchanges permit smooth adaptation promoting trust. This frees the quartet members to play with the potential disturbance of equilibrium inherent in entrained relationships and to play with this tension in an improvisatory way that enhances audience engagement and the live quality of performance. PMID:25400567

  20. Effectiveness of shrinkage-reducing admixtures on Portland pozzolan cement concrete

    Directory of Open Access Journals (Sweden)

    Videla, C.

    2005-06-01

    Full Text Available Drying shrinkage causes tensile stress in restrained concrete members. Since all structural elements are subject to some degree of restraint, drying shrinkage is regarded to be one of the main causes of concrete cracking. The purpose of the present study was to evaluate the effectiveness of SRA in reducing drying shrinkage strain in Portland pozzolan cement concrete. The major variables examined included slump, admixture type and dose, and specimen size. The measured results indicate that any of the admixtures used in the study significantly reduced shrinkage. Concrete manufactured with shrinkage reducing admixtures shrank an average of 43% less than concrete without admixtures. As a rule, the higher the dose of admixture, the higher was its shrinkage reduction performance. The experimental results were compared to the shrinkage strain estimated with the ACI 209, CEB MC 90, B3, GL 2000, Sakata 1993 and Sakata 2001 models. Although none of these models was observed to accurately describe the behaviour of Portland pozzolan cement concrete with shrinkage reducing admixtures, the Sakata 2001 model, with a weighted coefficient of variation of under 30%, may be regarded to be roughly adequate.

    La retracción por secado es un fenómeno intrínseco del hormigón que produce tensiones de tracción en elementos restringidos de hormigón. Puesto que todos los elementos presentan algún grado de retracción, se considera a la retracción por secado como una de las principales causas de agrietamiento en proyectos de construcción en hormigón. Por lo tanto, el objetivo de esta investigación fue evaluar la efectividad de los aditivos reductores de retracción (SRA en hormigones fabricados con cemento Portland puzolánico. Las variables principales estudiadas incluyen el asentamiento de cono de Abrams, marca y dosis de aditivo reductor de retracción, y tamaño de espécimen de hormigón. Los resultados obtenidos permiten concluir que el uso de

  1. Analysis of Environmental Impact for Concrete Using LCA by Varying the Recycling Components, the Compressive Strength and the Admixture Material Mixing

    Directory of Open Access Journals (Sweden)

    Taehyoung Kim

    2016-04-01

    Full Text Available Concrete is a type of construction material in which cement, aggregate, and admixture materials are mixed. When cement is produced, large amounts of substances that impact the environment are emitted during limestone extraction and clinker manufacturing. Additionally, the extraction of natural aggregate causes soil erosion and ecosystem destruction. Furthermore, in the process of transporting raw materials such as cement and aggregate to a concrete production company, and producing concrete in a batch plant, substances with an environmental impact are emitted into the air and water system due to energy use. Considering the fact that the process of producing concrete causes various environmental impacts, an assessment of various environmental impact categories is needed. This study used a life cycle assessment (LCA to evaluate the environmental impacts of concrete in terms of its global warming potential, acidification potential, eutrophication potential, ozone depletion potential, photochemical ozone creation potential, and abiotic depletion potential (GWP, AP, EP, ODP, POCP, ADP. The tendency was that the higher the strength of concrete, the higher the GWP, POCP, and ADP indices became, whereas the AP and EP indices became slightly lower. As the admixture mixing ratio of concrete increased, the GWP, AP, ODP, ADP, and POCP decreased, but EP index showed a tendency to increase slightly. Moreover, as the recycled aggregate mixing ratio of concrete increased, the AP, EP, ODP, and ADP decreased, while GWP and POCP increased. The GWP and POCP per unit compressed strength (1 MPa of high strength concrete were found to be about 13% lower than that for its normal strength concrete counterpart. Furthermore, in the case of AP, EP, ODP, and ADP per unit compressed strength (1 MPa, high-strength concrete was found to be about 10%~25% lower than its normal strength counterpart. Among all the environmental impact categories, ordinary cement was found to have

  2. Standard for prevention of gas entrainment phenomena in fast reactors. (2) Proposal of gas entrainment evaluation method

    International Nuclear Information System (INIS)

    For the stable operation of fast breeder reactors (FBRs), the occurrences of gas entrainment (GE) phenomena should be suppressed below an allowance level. Therefore, a reliable evaluation method for the GE phenomena is necessary to determine the operating conditions of FBRs. However, such a method has not yet been established, especially for the vortex-type GE. In this paper, the authors propose a GE evaluation method in which free surface vortices are identified from velocity fields by using the second invariant of the velocity gradient tensor, and GE evaluation parameters, e.g., gas core length, are calculated by using the Burgers vortex model. In addition, the standard method for the prevention of three kinds of vortex-type GE is shown by considering experimental data, evaluation results obtained by the proposed method and comparison results. Finally, it is confirmed that the onset conditions of the vortex-type GE can be evaluated by the proposed method. (author)

  3. Divergent photic thresholds in the non-image-forming visual system: entrainment, masking and pupillary light reflex

    OpenAIRE

    Butler, Matthew P.; Silver, Rae

    2010-01-01

    Light is the principal cue that entrains the circadian timing system, but the threshold of entrainment and the relative contributions of the retinal photoreceptors—rods, cones and intrinsically photosensitive retinal ganglion cells—are not known. We measured thresholds of entrainment of wheel-running rhythms at three wavelengths, and compared these to thresholds of two other non-image-forming visual system functions: masking and the pupillary light reflex (PLR). At the entrainment threshold, ...

  4. Application of a polycarboxylate ether admixture in RCC dam construction[ACI SP-239

    Energy Technology Data Exchange (ETDEWEB)

    Asmus, S.M.F.; Christensen, B.J.; Varley, N.J. [BASF Construction Chemicals Asia Pacific, Shanghai (China)

    2006-07-01

    Chemical admixtures are used in dam construction to improve plasticity of the dry materials mixture over time. Roller compacted concrete (RCC) has been used on many dam projects in China. However, the use of RCC has frequently resulted in water reduction problems. This paper provided details of an admixture based on polycarboxylate ether (PCE) which was developed to improve the quality of RCC constructions at the JinHong dam in China. Use of the polymer at the JinHong dam resulted in a vibration sensitive concrete that was sustained over time. Under identical mix-design and compaction conditions in the laboratory, specific gravity of the RCC was increased from 2417 kg/m{sup 3} to 2463 kg/m{sup 3}. The high specific gravity of the material resulted in satisfactory strength data from the dam project. The key-ratio of the splitting tensile strength versus compressive strength was higher than 8 per cent in all cases. A key advantage of the tailored PCE-RCC was the short Vebe times sustained over elapsed time in the RCC. Without additional compaction or vibration efforts, the specific density of RCC was better than conventional admixture technologies. The reduced viscosity provided cement paste films which formed on the surface of each layer of the RCC, which resulted in better bonding between the layers. It was concluded that the new PCE polymer is compatible with alternative retarder systems, which contributes to more extensive setting times under strict hydration regimes. 7 refs., 4 tabs., 4 figs.

  5. Effect of poly car boxy late admixtures on portland cement paste setting and rheological behaviour

    Directory of Open Access Journals (Sweden)

    Puertas, F.

    2005-03-01

    Full Text Available The objective of the work was to determine the effects of polycarboxilated-type admixture on the setting times and the rheological properties of different types of cements including CEM I 42.5 R, CEM Il/B-V 42.5 N and CEM III/B 32.5 N, defined according to the UNE EN 197-1:2000 standard. The results show that there is a lineal relationship between the initial setting times and the admixture dosage. Mathematical equations that model this behaviour for each of the cements have been determined. The data obtained from the minislump test and from the rheological parameters determined using the rheometer (plastic viscosity and yield stress point to similar conclusions. It was also verified that the workability effect of the polycarboxilate admixture is most intense for blended cements.

    El objetivo de este trabajo ha sido estudiar el efecto de la dosificación de un aditivo basado en policarboxilatos sobre el inicio de tiempo de fraguado y las propiedades reo lógicas en pastas de diferentes tipos de cemento (CEM 142.5 R, CEM 11/ B-V42.5 NYCEMIII/B 32.5 N-Norma EN 197-1:2000. existe una relación lineal entre el inicio del fraguado y la dosificación del aditivo, se han determinado las ecuaciones matemáticas que describen este comportamiento para cada cemento, los resultados obtenidos sobre la fluidez de la pasta en el ensayo del "minislump" coinciden con la evolución de los valores de los parámetros reológicos (esfuerzo de cizalladura y viscosidad plástica determinados a través de un reómetro. el efecto fluidificante del aditivo superplastificante basado en policarboxilatos es mucho más marcado en cementos que contienen adiciones.

  6. Variation in genetic admixture and population structure among Latinos: the Los Angeles Latino eye study (LALES

    Directory of Open Access Journals (Sweden)

    Le Marchand Loic

    2009-11-01

    Full Text Available Abstract Background Population structure and admixture have strong confounding effects on genetic association studies. Discordant frequencies for age-related macular degeneration (AMD risk alleles and for AMD incidence and prevalence rates are reported across different ethnic groups. We examined the genomic ancestry characterizing 538 Latinos drawn from the Los Angeles Latino Eye Study [LALES] as part of an ongoing AMD-association study. To help assess the degree of Native American ancestry inherited by Latino populations we sampled 25 Mayans and 5 Mexican Indians collected through Coriell's Institute. Levels of European, Asian, and African descent in Latinos were inferred through the USC Multiethnic Panel (USC MEP, formed from a sample from the Multiethnic Cohort (MEC study, the Yoruba African samples from HapMap II, the Singapore Chinese Health Study, and a prospective cohort from Shanghai, China. A total of 233 ancestry informative markers were genotyped for 538 LALES Latinos, 30 Native Americans, and 355 USC MEP individuals (African Americans, Japanese, Chinese, European Americans, Latinos, and Native Hawaiians. Sensitivity of ancestry estimates to relative sample size was considered. Results We detected strong evidence for recent population admixture in LALES Latinos. Gradients of increasing Native American background and of correspondingly decreasing European ancestry were observed as a function of birth origin from North to South. The strongest excess of homozygosity, a reflection of recent population admixture, was observed in non-US born Latinos that recently populated the US. A set of 42 SNPs especially informative for distinguishing between Native Americans and Europeans were identified. Conclusion These findings reflect the historic migration patterns of Native Americans and suggest that while the 'Latino' label is used to categorize the entire population, there exists a strong degree of heterogeneity within that population, and that

  7. Polar and brown bear genomes reveal ancient admixture and demographic footprints of past climate change

    Science.gov (United States)

    Miller, Webb; Schuster, Stephan C.; Welch, Andreanna J.; Ratan, Aakrosh; Bedoya-Reina, Oscar C.; Zhao, Fangqing; Kim, Hie Lim; Burhans, Richard C.; Drautz, Daniela I.; Wittekindt, Nicola E.; Tomsho, Lynn P.; Ibarra-Laclette, Enrique; Herrera-Estrella, Luis; Peacock, Elizabeth; Farley, Sean; Sage, George K.; Rode, Karyn; Obbard, Martyn E.; Montiel, Rafael; Bachmann, Lutz; Ingólfsson, Ólafur; Aars, Jon; Mailund, Thomas; Wiig, Øystein; Talbot, Sandra L.; Lindqvist, Charlotte

    2012-01-01

    Polar bears (PBs) are superbly adapted to the extreme Arctic environment and have become emblematic of the threat to biodiversity from global climate change. Their divergence from the lower-latitude brown bear provides a textbook example of rapid evolution of distinct phenotypes. However, limited mitochondrial and nuclear DNA evidence conflicts in the timing of PB origin as well as placement of the species within versus sister to the brown bear lineage. We gathered extensive genomic sequence data from contemporary polar, brown, and American black bear samples, in addition to a 130,000- to 110,000-y old PB, to examine this problem from a genome-wide perspective. Nuclear DNA markers reflect a species tree consistent with expectation, showing polar and brown bears to be sister species. However, for the enigmatic brown bears native to Alaska's Alexander Archipelago, we estimate that not only their mitochondrial genome, but also 5–10% of their nuclear genome, is most closely related to PBs, indicating ancient admixture between the two species. Explicit admixture analyses are consistent with ancient splits among PBs, brown bears and black bears that were later followed by occasional admixture. We also provide paleodemographic estimates that suggest bear evolution has tracked key climate events, and that PB in particular experienced a prolonged and dramatic decline in its effective population size during the last ca. 500,000 years. We demonstrate that brown bears and PBs have had sufficiently independent evolutionary histories over the last 4–5 million years to leave imprints in the PB nuclear genome that likely are associated with ecological adaptation to the Arctic environment.

  8. Reduced bleed air extraction for DC-10 cabin air conditioning

    Science.gov (United States)

    Newman, W. H.; Viele, M. R.; Hrach, F. J.

    1980-01-01

    It is noted that a significant fuel savings can be achieved by reducing bleed air used for cabin air conditioning. Air in the cabin can be recirculated to maintain comfortable ventilation rates but the quality of the air tends to decrease due to entrainment of smoke and odors. Attention is given to a development system designed and fabricated under the NASA Engine Component Improvement Program to define the recirculation limit for the DC-10. It is shown that with the system, a wide range of bleed air reductions and recirculation rates is possible. A goal of 0.8% fuel savings has been achieved which results from a 50% reduction in bleed extraction from the engine.

  9. Flow Dynamics and Sediment Entrainment in Natural Turbidity Currents Inferred from Numerical Modeling

    Science.gov (United States)

    Traer, M. M.; Hilley, G. E.; Fildani, A.

    2009-12-01

    Submarine turbidity currents derive their momentum from gravity acting upon the density contrast between sediment-laden and clear water, and so unlike fluvial systems, the dynamics of such flows are inextricably linked to the rates at which they deposit and entrain sediment. We have analyzed the sensitivity of the growth and maintenance of turbidity currents to sediment entrainment and deposition using the layer-averaged equations of conservation of fluid and sediment mass, and conservation of momentum and turbulent kinetic energy. Our model results show that the dynamics of turbidity currents are extremely sensitive to the functional form and empirical constants of the relationship between sediment entrainment and friction velocity. Data on the relationship between sediment entrainment and friction velocity for submarine density flows are few and as a result, entrainment formulations are populated with data from sub-aerial flows not driven by the density contrast between clear and turbid water. If we entertain the possibility that sediment entrainment in sub-aerial rivers is different than in dense underflows, flow parameters such as velocity, height, and concentration were found nearly impossible to predict beyond a few hundred meters based on the limited laboratory data available that constrain the sediment entrainment process in turbidity currents. The sensitivity of flow dynamics to the functional relationship between friction velocity and sediment entrainment indicates that independent calibration of a sediment entrainment law in the submarine environment is necessary to realistically predict the dynamics of these flows and the resulting patterns of erosion and deposition. To calibrate such a relationship, we have developed an inverse methodology that utilizes existing submarine channel morphology as a means of constraining the sediment entrainment function parameters. We use a Bayesian Metropolis-Hastings sampler to determine the sediment entrainment

  10. Rectification cleaning AsCl3 from the admixture of oxygen

    Directory of Open Access Journals (Sweden)

    Maznitska O. V.

    2008-06-01

    Full Text Available The process of the rectification cleaning of three-chlorous arsenic from the admixtures of products of his hydrolysis in the atmosphere of chlorous hydrogen has been considered in the article. Dependence of coefficient of relative volatility a three-chlorous arsenic from his concentration in muriatic solution is explored. The conduct of coefficient of relative volatility with concentrations of HCl and AsCl3 is compared. Saving of equalization of balance and equalization of working curve of column at such conduct of process of rectification is shown.

  11. An experimental study of the combustion characteristics of groundnut shell and waste paper admixture briquettes

    OpenAIRE

    O.A Oyelaran; B.O. Bolaji; M.A. Waheed; Adekunle, M.F.

    2015-01-01

    The study was undertaken to assess the heat released of briquettes produced from waste paper and groundnut shell admixture in five mixing ratios (90:10; 80:20; 70:30; 60:40; and 50:50). The briquettes were prepared on an existing motorized briquetting machine. The suitability of briquetted fuel as domestic fuel was studied in terms of flame propagation, afterglow, calorific value, and utilized heat, after sun drying the prepared briquettes for nineteen (19) days. The results of propagation ra...

  12. Compost admixture impact study on water infiltration depth, water front advance and recession in irrigated environment

    International Nuclear Information System (INIS)

    Water is an important life supporting resource and is essential for sustainable food production. Its continued decrease has diverted the attention of researchers to find new ways of efficient irrigation management. Decomposed bio-solids (for example leaves, crop residue, animal waste, municipal solid waste) form the compost and provide friendly environment for enhancing crop production. The present study investigates the effects of compost admixture on water infiltration depth, water advance and recession phase of irrigation event in the field having loamy sand texture. Compost from two sources was used. There were nine experimental plots with 3.5 m width and 45 m length. Compost at the rate of 5 % was incorporated up to a depth of 3 cm in six plots (3 plots of each compost source) and in the remaining three plots no compost was applied. The field was irrigated twice. The results revealed that by using 5% compost admixture by weight the advance time reduced by 23.96% and 26.83 % for first and second irrigation, respectively compared to non compost admixture plots. Results revealed that by using 5 % compost up to 3 cm mixing depth the water infiltration depth decreased 42.97 % at head side of the field and 10.37 % at tail side of field during first irrigation, during second irrigation the water infiltration depth decreased 48.67 % at upper end of the field and 11.28 % at lower end of the field. The significant decrease in water infiltration depth at head side gives uniformity in water infiltration depth along the length of field. The faster movement of the water front with the application of compost admixture reduces the difference in intake opportunity times between the head and far end of the field, thus it improves the performance of the irrigation system. Reduction in the applied water volume to the tone of 23.96% during first irrigation and 26.83% during second irrigation, further supports this improvement in irrigation performance, considering on the advance

  13. An investigation of admixture in an Australian Aboriginal Y-chromosome STR database.

    Science.gov (United States)

    Taylor, Duncan; Nagle, Nano; Ballantyne, Kaye N; van Oorschot, Roland A H; Wilcox, Stephen; Henry, Julianne; Turakulov, Rust; Mitchell, R John

    2012-09-01

    Y-chromosome specific STR profiling is increasingly used in forensic casework. However, the strong geographic clustering of Y haplogroups can lead to large differences in Y-STR haplotype frequencies between different ethnicities, which may have an impact on database composition in admixed populations. Aboriginal people have inhabited Australia for over 40,000 years and until ∼300 years ago they lived in almost complete isolation. Since the late 18th century Australia has experienced massive immigration, mainly from Europe, although in recent times from more widespread origins. This colonisation resulted in highly asymmetrical admixture between the immigrants and the indigenes. A State jurisdiction within Australia has created an Aboriginal Y-STR database in which assignment of ethnicity was by self-declaration. This criterion means that some males who identify culturally as members of a particular ethnic group may have a Y haplogroup characteristic of another ethnic group, as a result of admixture in their paternal line. As this may be frequent in Australia, an examination of the extent of genetic admixture within the database was performed. A Y haplogroup predictor program was first used to identify Y haplotypes that could be assigned to a European haplogroup. Of the 757 males (589 unique haplotypes), 445 (58.8%) were identified as European (354 haplotypes). The 312 non-assigned males (235 haplotypes) were then typed, in a hierarchical fashion, with a Y-SNP panel that detected the major Y haplogroups, C-S, as well as the Aboriginal subgroup of C, C4. Among these 96 males were found to have non-Aboriginal haplogroups. In total, ∼70% of Y chromosomes in the Aboriginal database could be classed as non-indigenous, with only 169 (129 unique haplotypes) or 22% of the total being associated with haplogroups denoting Aboriginal ancestry, C4 and K* or more correctly K(xL,M,N,O,P,Q,R,S). The relative frequencies of these indigenous haplogroups in South Australia (S

  14. No clear effect of admixture betweent two european invading outbreaks of Diabrotica virgifera virgifera in natura

    OpenAIRE

    Cavigliasso, Fanny; Mallez, Sophie,; Spencer, Joseph; Guillemaud, Thomas

    2014-01-01

    In this study, we challenged the hypothesis that admixture may have had a positive impact in the context of the European invasion of the western corn rootworm (WCR), Diabrotica virgifera virgifera, LeConte. This beetle was introduced in Europe from the USA several times since the 1980’s. The multiple introductions of this major pest of cultivated corn led to the formation of two major outbreaks in North Western (NW) Italy and in Central and South Eastern (CSE) Europe that eventually merged in...

  15. COP Prediction of an ejector refrigeration cycle combined with a vapour compression cycle for automotive air conditioning

    OpenAIRE

    Nat Suvarnakuta; Nutthanun Keerlatiyadatanapat; Thanarath Sriveerakul

    2014-01-01

    This paper presents the COP prediction of an ejector refrigeration cycle combined with a vapour compression cycle for automotive air conditioning. Using computational fluid dynamics (CFD) technique, the performance of an ejector was analyzed in term of the entrainment ratio (Rm) and critical back pressure (CBP). The results from this study were compared with a previous study of combined ejector refrigeration system for automotive air conditioning application [1] which the entrainment ratio (R...

  16. Marching along to an Offbeat Drum: Entrainment of Synthetic Gene Oscillators by a Noisy Stimulus.

    Science.gov (United States)

    Butzin, Nicholas C; Hochendoner, Philip; Ogle, Curtis T; Hill, Paul; Mather, William H

    2016-02-19

    Modulation of biological oscillations by stimuli lies at the root of many phenomena, including maintenance of circadian rhythms, propagation of neural signals, and somitogenesis. While it is well established that regular periodic modulation can entrain an oscillator, an aperiodic (noisy) modulation can also robustly entrain oscillations. This latter scenario may describe, for instance, the effect of irregular weather patterns on circadian rhythms, or why irregular neural stimuli can still reliably transmit information. A synthetic gene oscillator approach has already proven to be useful in understanding the entrainment of biological oscillators by periodic signaling, mimicking the entrainment of a number of noisy oscillating systems. We similarly seek to use synthetic biology as a platform to understand how aperiodic signals can strongly correlate the behavior of cells. This study should lead to a deeper understanding of how fluctuations in our environment and even within our body may promote substantial synchrony among our cells. Specifically, we investigate experimentally and theoretically the entrainment of a synthetic gene oscillator in E. coli by a noisy stimulus. This phenomenon was experimentally studied and verified by a combination of microfluidics and microscopy using the real synthetic circuit. Stochastic simulation of an associated model further supports that the synthetic gene oscillator can be strongly entrained by aperiodic signals, especially telegraph noise. Finally, widespread applicability of aperiodic entrainment beyond the synthetic gene oscillator is supported by results derived from both a model for a natural oscillator in D. discoideum and a model for predator-prey oscillations. PMID:26524465

  17. Quadrupedal Locomotion-Respiration Entrainment and Metabolic Economy in Cross-Country Skiers.

    Science.gov (United States)

    Boldt, Kevin; Killick, Anthony; Herzog, Walter

    2016-02-01

    A 1:1 locomotion-respiration entrainment is observed in galloping quadrupeds, and is thought to improve running economy. However, this has not been tested directly in animals, as animals cannot voluntarily disrupt this entrainment. The purpose of this study was to evaluate metabolic economy in a human gait involving all four limbs, cross-country skiing, in natural entrainment and forced nonentrainment. Nine elite cross-country skiers roller skied at constant speed using the 2-skate technique. In the first and last conditions, athletes used the natural entrained breathing pattern: inhaling with arm recovery and exhaling with arm propulsion, and in the second condition, the athletes disentrained their breathing pattern. The rate of oxygen uptake (VO2) and metabolic rate (MR) were measured via expired gas analysis. Propulsive forces were measured with instrumented skis and poles. VO2 and MR increased by 4% and 5% respectively when skiers used the disentrained compared with the entrained breathing pattern. There were no differences in ski or pole forces or in timing of the gait cycle between conditions. We conclude that breathing entrainment reduces metabolic cost of cross-country skiing by approximately 4%. Further, this reduction is likely a result of the entrainment rather than alterations in gait mechanics. PMID:26252735

  18. Neurobiological foundations of neurologic music therapy: rhythmic entrainment and the motor system.

    Science.gov (United States)

    Thaut, Michael H; McIntosh, Gerald C; Hoemberg, Volker

    2014-01-01

    Entrainment is defined by a temporal locking process in which one system's motion or signal frequency entrains the frequency of another system. This process is a universal phenomenon that can be observed in physical (e.g., pendulum clocks) and biological systems (e.g., fire flies). However, entrainment can also be observed between human sensory and motor systems. The function of rhythmic entrainment in rehabilitative training and learning was established for the first time by Thaut and colleagues in several research studies in the early 1990s. It was shown that the inherent periodicity of auditory rhythmic patterns could entrain movement patterns in patients with movement disorders (see for a review: Thaut et al., 1999). Physiological, kinematic, and behavioral movement analysis showed very quickly that entrainment cues not only changed the timing of movement but also improved spatial and force parameters. Mathematical models have shown that anticipatory rhythmic templates as critical time constraints can result in the complete specification of the dynamics of a movement over the entire movement cycle, thereby optimizing motor planning and execution. Furthermore, temporal rhythmic entrainment has been successfully extended into applications in cognitive rehabilitation and speech and language rehabilitation, and thus become one of the major neurological mechanisms linking music and rhythm to brain rehabilitation. These findings provided a scientific basis for the development of neurologic music therapy. PMID:25774137

  19. Neurobiological Foundations of Neurologic Music Therapy: Rhythmic Entrainment and the Motor System

    Directory of Open Access Journals (Sweden)

    Michael eThaut

    2015-02-01

    Full Text Available AbstractEntrainment is defined by a temporal locking process in which one system’s motion or signal frequency entrains the frequency of another system. This process is a universal phenomenon that can be observed in physical (e.g., pendulum clocks and biological systems (e.g. fire flies. However, entrainment can also be observed between human sensory and motor systems. The function of rhythmic entrainment in rehabilitative training and learning was established for the first time by Thaut and colleagues in several research studies in the early 1990s. It was shown that the inherent periodicity of auditory rhythmic patterns could entrain movement patterns in patients with movement disorders (see for a review: Thaut et al, 1999. Physiological, kinematic and behavioral movement analysis showed very quickly that entrainment cues not only changed the timing of movement but also improved spatial and force parameters. Mathematical models have shown that anticipatory rhythmic templates as critical time constraints can result in the complete specification of the dynamics of a movement over the entire movement cycle, thereby optimizing motor planning and execution. Furthermore, temporal rhythmic entrainment has been successfully extended into applications in cognitive rehabilitation and speech and language rehabilitation, and thus become one of the major neurological mechanisms linking music and rhythm to brain rehabilitation. These findings provided a scientific basis for the development of Neurologic Music Therapy.

  20. Estimates of entrainment mortality for striped bass and other fish species inhabiting the Hudson River estuary

    International Nuclear Information System (INIS)

    An empirically derived age-, time-, and space-variant equation was used to estimate entrainment mortality at power plants for seven fish species inhabiting the Hudson River estuary. Entrainment mortality is expressed as a conditional rate, which is the fractional reduction in year-class strength due to entrainment if other sources of mortality are density-independent. Estimates of the conditional entrainment mortality, based on historical and projected once-through cooling operation of five power plants, were 11-22% for striped bass, 11-17% for white perch, 5-7% for Atlantic tomcod, 14-21% for American shad, 4-11% for river herring (alewife and blueback herring combined), and 35-79% for bay anchovy. Closed-cycle cooling (natural-draft cooling towers) at three of the power plants (Indian Point, Bowline Point, and Roseton) would reduce entrainment mortality of striped bass by 50-80%, of white perch by 75-80%, of Atlantic tocod by 65-70%, of American shad by 80%, of river herring by 30-90%, and of bay anchovy by 45-80%. The life stages most vulnerable to entrainment mortality were post-yolk-sac larva and entrainable size juvenile. 18 refs., 7 tabs

  1. Entrainment Across a Sheared Density Interface in High Richardson Number Cavity Flow

    Science.gov (United States)

    Williamson, Nicholas; Kirkpartick, Michael; Armfield, Steve

    2015-11-01

    The turbulent entrainment of fluid across a sharp density interface has been examined experimentally in a purging cavity flow. In the experiments, a long straight cavity with sloped entry and exit boundaries is located in the base of a straight open channel. Saline fluid is entrained from the cavity into the overflow. The cavity geometry has been designed to ensure there is no separation of the overflow in the cavity region with the goal of obtaining a single mode of entrainment, related only to the interface properties rather than to cavity specific mechanisms. The bulk entrainment rate has been measured and correlated with bulk Richardson number over Ri = 1 . 0 - 20 at Reynolds number Re = 7100 - 15100 . The entrainment rate is shown to scale with the local bulk Richardson number E ~= CRi - 1 . 38 , very close to the established result for entrainment across a sharp two layer density interface in a recirculating water channel (Strang and Fernando, J Fluid Mech., 428, 2001) but with an order of magnitude lower coefficient C. Experiments instrumented with PIV/LIF were used to relate the bulk Ri to the local gradient Richardson number of the interface. In the cavity setting the interface appears to remain sharper, resulting in larger Rig and reduced entrainment.

  2. Fish entrainment rates through towboat propellers in the Upper Mississippi and Illinois rivers

    Science.gov (United States)

    Jack, Killgore K.; Miranda, L.E.; Murphy, C.E.; Wolff, D.M.; Hoover, J.J.; Keevin, T.M.; Maynord, S.T.; Cornish, M.A.

    2011-01-01

    Aspecially designed netwas used to study fish entrainment and injury through towboat propellers in 13 pools of the Upper Mississippi and Illinois rivers. The net was attached to the stern of a 48.8-m-long towboat with twin propellers (in Kort propulsion nozzles), and sampling typically took place while the towboat pushed 15 loaded barges upstream at a time. In total, 254 entrainment samples over 894 km of the 13 study pools were collected. The sampling efforts produced 16,005 fish representing 15 families and at least 44 species; fish ranged in total length from 3 to 123 cm, but only 12.5-cm or longer fish were analyzed because smaller fish could escape through the mesh of the trawl. Clupeidae (68% of total catch) and Sciaenidae (21%) were the dominant families. We detected no effects of towboat operation variables (speed and engine [i.e., propeller] revolutions per minute [RPM]) on entrainment rate (i.e., fish/km), but entrainment rate showed a wedge-shaped distribution relative to hydraulic and geomorphic characteristics of the channel. Entrainment rate was low (30 fish/km). Although total entrainment rate was not related to engine RPM, the probability of being struck by a propeller increased with fish length and engine RPM. Limits on engine RPM in narrow, shallow, and sluggish reaches could reduce entrainment impact, particularly for large-bodied fish. ?? American Fisheries Society 2011.

  3. A Comparative Study on Compressive and Flexural Strength of Concrete Containing Different Admixtures as Partial Replacement of Cement

    Directory of Open Access Journals (Sweden)

    Apoorv Singh

    2014-09-01

    Full Text Available Concrete is the most widely used material in the world today. This paper is about the comparative study of the flexural strength and compressive strength of concrete when different admixtures are used as partial replacement of cement in the concrete mix. The mineral admixtures that are used here are Silica Fume, Rice Husk Ash and Iron slag as partial replacement of cement. All these materials are industrial waste products and are abundantly available nowadays. These materials have high silica content and pozzolanic properties and can be effectively used as a replacement of cement during the formation of High Performance Concrete. Compressive and Flexural strength are the two most important characteristic of concrete and are calculated for the hardened concrete to analyze the load bearing capacity for design purposes. Thus for the effective judgment of type of mineral admixtures to be used a comparative study is very useful.

  4. A study of annular flows with bubbles in the liquid ring and entrained droplets by means of stochastic analysis techniques

    International Nuclear Information System (INIS)

    By employing stochastic analysis techniques, an experimental study of a large number of annular flows with bubbles in the liquid ring and entrained droplets has been undertaken in the experimental air-water loop FREDLI, in which the information carrier is two visible light beams crossing the diameter of the tube and modulated by the scattering of the photons at the randomly arriving interfaces; also, some earlier neutron noise measurements in the upper part of a commercial BWR core are carefully analyzed. For the BWR measurements, it is shown for the first time that in the upper part of the core, there are usually three peaks in the cross-correlation function and that all noise analytic functions look extraordinarily similar to the corresponding noise analytic functions of some of the investigated annular flows at the FREDLI loop; a plausible explanation of these findings is given. (Auth.)

  5. Experimental study on scale effect on gas entrainment at free surface

    International Nuclear Information System (INIS)

    It is necessary to understand effects of scale and fluid properties on gas entrainment phenomena for prediction of gas entrainment in a fast breeder reactor (FBR). In the present study, three models of different scales but of similar geometry were used for water tests to examine the effects of scale and viscosity. The results have shown that the critical Froude (Fr) number, above which gas entrainment appears, drastically decreases as the scale increase. A prediction method using the Fr-Re map is proposed in the present paper for the sodium flow in an FBR. (orig.)

  6. Effects of entrainment through Oconee Nuclear Station on carbon-14 assimilation rates of phytoplankton

    International Nuclear Information System (INIS)

    Carbon assimilation rates of phytoplankton communities entrained through Oconee Nuclear Station were measured on six dates during 1974. Thermal, mechanical, condenser, and multiple entrainment effects on uptake rates were compared by incubating samples in vitro in controlled-temperature water baths. Duplicate light and dark bottles containing water from four cooling-system locations were exposed to temperatures approximating intake and discharge temperatures. The relationships were variable, but exposure of the hypolimnetic intake water at near-discharge temperatures (thermal effect) stimulated primary productivity in four of six experiments. Multiple entrainment and mechanical effects caused no consistent change in assimilation rates

  7. Laboratory experiments investigating entrainment by debris flows and associated increased mobility

    Science.gov (United States)

    Moberly, D.; Maki, L.; Hill, K. M.

    2014-12-01

    As debris flows course down a steep hillside they entrain bed materials such as loose sediments. The entrainment of materials not only increases the size of the debris flows but the mobility as well. The mechanics underlying the particle entrainment and the associated increased mobility are not well-understood. Existing models for the entrainment process include those that explicitly consider stress ratios, the angle of inclination, and the particle fluxes relative to those achieved under steady conditions. Others include an explicit consideration of the physics of the granular state: the visco-elastic nature of particle flows and, alternatively, the role of macroscopic force chains. Understanding how well these different approaches account for entrainment and deposition rates is important for accurate debris flow modeling, both in terms of the rate of growth and also in terms of the increased mobility associated with the entrainment. We investigate how total and instantaneous entrainment and deposition vary with macroscopic stresses and particle-scale interactions for different particle sizes and different fluid contents using laboratory experiments in an instrumented experimental laboratory debris flow flume. The flume has separate, independent water supplies for the bed and "supply" (parent debris flow), and the bed is instrumented with pore pressure sensors and a basal stress transducer. We monitor flow velocities, local structure, and instantaneous entrainment and deposition rates using a high speed camera. We have found that systems with a mixture of particle sizes are less erosive and more depositional than systems of one particle size under otherwise the same conditions. For both mixtures and single-sized particle systems, we have observed a relatively linear relationship between total erosion and the slope angle for dry flows. Increasing fluid content typically increases entrainment. Measurements of instantaneous entrainment indicate similar dependencies

  8. The modelling of de-entrainment in a PWR upper plenum during reflood

    International Nuclear Information System (INIS)

    Entrainment/de-entrainment and steam binding are dominant contributor to uncertainty in the prediction of peak cladding temperature (PCT) during a LOCA (Boyack, 1989). In a realistic analysis of the large break LOCA, therefore, it is important to use a reasonably accurate physical model for the upper plenum. It is particularly important not to overestimate the amount of liquid stored in the upper plenum, since this will cause under-estimation of steam binding, which is a key aspect limiting heat transfer during reflood. This paper describes the process used to assess the performance of WCOBRA/TRAC code relative to de-entrainment in the upper plenum. (author)

  9. Experimental study of liquid properties' effect on gas entrainment phenomena induced by vortices

    International Nuclear Information System (INIS)

    The effects of liquid properties on gas entrainment at free surfaces has been experimentally studied for the vessels of a liquid metal fast breeder reactor. Experiments using a transparent cylindrical test section with fluids of different properties were carried out to examine the effects of surface flow upon the gas entrainment induced by vortices. The experimental results showed that the velocity fluctuation, which was enhanced by the surface flow, decreased viscosity effects on the gas entrainment critical condition and increased the surface tension effect. In the unstable and turbulent flow condition, the critical velocity in liquid sodium was predicted to be about 1.6 times as high as that in water. (author)

  10. Investigation of Pressurized Entrained-Flow Kraft Black Liquor Gasification in an Industrially Relevant Environment

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2008-06-30

    The University of Utah's project 'Investigation of Pressurized Entrained-Flow Kraft Black Liquor Gasification in an Industrially Relevant Environment' (U.S. DOE Cooperative Agreement DE-FC26-04NT42261) was a response to U.S. DOE/NETL solicitation DE-PS36-04GO94002, 'Biomass Research and Development Initiative' Topical Area 4-Kraft Black Liquor Gasification. The project began September 30, 2004. The objective of the project was to improve the understanding of black liquor conversion in high pressure, high temperature reactors that gasify liquor through partial oxidation with either air or oxygen. The physical and chemical characteristics of both the gas and condensed phase were to be studied over the entire range of liquor conversion, and the rates and mechanisms of processes responsible for converting the liquor to its final smelt and syngas products were to be investigated. This would be accomplished by combining fundamental, lab-scale experiments with measurements taken using a new semi-pilot scale pressurized entrained-flow gasifier. As a result of insufficient availability of funds and changes in priority within the Office of Biomass Programs of the U.S. Department of Energy, the research program was terminated in its second year. In total, only half of the budgeted funding was made available for the program, and most of this was used during the first year for construction of the experimental systems to be used in the program. This had a severe impact on the program. As a consequence, most of the planned research was unable to be performed. Only studies that relied on computational modeling or existing experimental facilities started early enough to deliver useful results by the time to program was terminated Over the course of the program, small scale (approx. 1 ton/day) entrained-flow gasifier was designed and installed at the University of Utah's off-campus Industrial Combustion and Gasification Research Facility. The system is

  11. Alkali-activated complex binders from class C fly ash and Ca-containing admixtures.

    Science.gov (United States)

    Guo, Xiaolu; Shi, Huisheng; Chen, Liming; Dick, Warren A

    2010-01-15

    Processes that maximize utilization of industrial solid wastes are greatly needed. Sodium hydroxide and sodium silicate solution were used to create alkali-activated complex binders (AACBs) from class C fly ash (CFA) and other Ca-containing admixtures including Portland cement (PC), flue gas desulfurization gypsum (FGDG), and water treatment residual (WTR). Specimens made only from CFA (CFA100), or the same fly ash mixed with 40 wt% PC (CFA60-PC40), with 10 wt% FGDG (CFA90-FGDG10), or with 10 wt% WTR (CFA90-WTR10) had better mechanical performance compared to binders using other mix ratios. The maximum compressive strength of specimens reached 80.0 MPa. Geopolymeric gel, sodium polysilicate zeolite, and hydrated products coexist when AACB reactions occur. Ca from CFA, PC, and WTR precipitated as Ca(OH)(2), bonded in geopolymers to obtain charge balance, or reacted with dissolved silicate and aluminate species to form calcium silicate hydrate (C-S-H) gel. However, Ca from FGDG probably reacted with dissolved silicate and aluminate species to form ettringite. Utilization of CFA and Ca-containing admixtures in AACB is feasible. These binders may be widely utilized in various applications such as in building materials and for solidification/stabilization of other wastes, thus making the wastes more environmentally benign. PMID:19767143

  12. Genetic admixture history of Eastern Indonesia as revealed by Y-chromosome and mitochondrial DNA analysis.

    Science.gov (United States)

    Mona, Stefano; Grunz, Katharina E; Brauer, Silke; Pakendorf, Brigitte; Castrì, Loredana; Sudoyo, Herawati; Marzuki, Sangkot; Barnes, Robert H; Schmidtke, Jörg; Stoneking, Mark; Kayser, Manfred

    2009-08-01

    Eastern Indonesia possesses more linguistic diversity than any other region in Southeast Asia, with both Austronesian (AN) languages that are of East Asian origin, as well as non-Austronesian (NAN) languages of likely Melanesian origin. Here, we investigated the genetic history of human populations from seven eastern Indonesian islands, including AN and NAN speakers, as well as the relationship between languages and genes, by means of nonrecombining Y-chromosomal (NRY) and mitochondrial DNA (mtDNA) analysis. We found that the eastern Indonesian gene pool consists of East Asian as well as Melanesian components, as might be expected based on linguistic evidence, but also harbors putative indigenous eastern Indonesian signatures that perhaps reflect the initial occupation of the Wallacea by aboriginal hunter-gatherers already in Palaeolithic times. Furthermore, both NRY and mtDNA data showed a complete lack of correlation between linguistic and genetic relationships, most likely reflecting genetic admixture and/or language shift. In addition, we noted a small fraction of the NRY and mtDNA data shared between eastern Indonesians and Australian Aborigines likely reflecting an ancient link between Asia and Australia. Our data thus provide insights into the complex genetic ancestry history of eastern Indonesian islanders characterized by several admixture episodes and demonstrate a clear example of the lack of the often-assumed correlation between the genes and languages of human populations. PMID:19414523

  13. Improvement Of Sub-Grade Soil Properties Using Admixture Quarry Dust And Woven Geo-Textile

    Directory of Open Access Journals (Sweden)

    G. Priya Vasudha

    2015-08-01

    Full Text Available Abstract The important factor for design and construction of pavement is the behavior of underlying sub-grade. Large deformations in the sub-grade will lead to a continuous deterioration of the paved surface. As the sub-grade soil is too weak to bear the load engineering solutions such as geo reinforcement using geo-synthetics are additives which are earlier used in sub-grade improvement and such experimental study is carried by pervious authors. This paper deals with the sub-grade improvement using geo-textile as a reinforcement sheet and quarry dust as admixtures. In order to increase the strength of the sub-grade the quarry dust is varied with different percentages i.e. 0 5 10 15 20 and 25. In this study Proctors compaction tests and CBR soaked and unsoaked tests are conducted on locally available soil with reinforced material and with admixture. For this study it is identified that the engineering properties of the soil is improved in all conditions. The soil with quarry dust at optimum value is 20 has CBR soaked value is obtained 6.83 and unsoaked value is obtained 7.02 is increased when compared with conventionally soil. The soil quarry dust at optimum value is at 20 and Geo-textile has CBR soaked value is 6.59 and unsoaked value is 8.95 is increased when compared with conventionally soil and soil with quarry dust.

  14. Preparation of High Impermeable and Crack-resistance Chemical Admixture and Its Mechanism

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A kind of high impermeable and crack-resistance chemical admixture (HICRCA) was prepared, which is a compound chemical admixture composed of an expansion ingredient,density ingredient, and organic hydrophobic poreblocking ingredient. The results of the experiments indicate that the addition of HICRCA improves mortar and concrete in the following performances:(1) perfect workability: slump is more than 22cm, the slump after 3h is about 16cm; (2)high impermeability:for the mortar,the pervious height under a water pressure of 1.5MPa is 1.5cm,for the concrete, the pervious height under a water pressure of 5.0MPa is 2.2cm;(3)high crack-resistance:there is a micro-expansion at the age of 90d;(4)high compressivestrength:compared with the controlled concrete,the compressive strengths at the age of 3d and 28d are improved by 66.4% and 62.0%, respectively.At the same time,the effects of different curing condition on mortar and concrete expansive and shrinkage performance were studied.In addition,the impermeable and crack-resistance mechanism was investigated in the present paper.

  15. Growth and characterization of pure and semiorganic nonlinear optical Lithium Sulphate admixtured l-alanine crystal

    Science.gov (United States)

    Vela, T.; Selvarajan, P.; Freeda, T. H.; Balasubramanian, K.

    2013-04-01

    Lithium sulphate admixtured l-alanine (LSLA) salt was synthesized and the solubility of the commercially available l-alanine and the synthesized LSLA sample was determined in de-ionized water at various temperatures. In accordance with the solubility data, the saturated aqueous solutions of l-alanine and lithium admixtured l-alanine were prepared separately and the single crystals of the samples were grown by the solution method with a slow evaporation technique. Studying single x-ray diffraction shows that pure and LSLA crystal belong to the orthorhombic system with a non-centrosymmetric space group P212121. Using the powder x-ray diffraction study, the crystallinity of the grown crystals is confirmed and the diffraction peaks are indexed. The various functional groups present in the pure and LSLA crystal are elucidated from Fourier transform infrared spectroscopy study. UV-visible transmittance is recorded to study the optical transmittance range for the grown crystals. The powder second harmonic generation test confirms the nonlinear optical property of the grown crystals. From the microhardness test, the hardness of the grown crystals is estimated. The dielectric behaviour, such as the dielectric constant and the loss of the sample, are measured as a function of temperature and frequency. The ac conductivity of the grown crystals is also studied and the activation energy is calculated.

  16. Growth and characterization of pure and semiorganic nonlinear optical Lithium Sulphate admixtured l-alanine crystal

    International Nuclear Information System (INIS)

    Lithium sulphate admixtured l-alanine (LSLA) salt was synthesized and the solubility of the commercially available l-alanine and the synthesized LSLA sample was determined in de-ionized water at various temperatures. In accordance with the solubility data, the saturated aqueous solutions of l-alanine and lithium admixtured l-alanine were prepared separately and the single crystals of the samples were grown by the solution method with a slow evaporation technique. Studying single x-ray diffraction shows that pure and LSLA crystal belong to the orthorhombic system with a non-centrosymmetric space group P212121. Using the powder x-ray diffraction study, the crystallinity of the grown crystals is confirmed and the diffraction peaks are indexed. The various functional groups present in the pure and LSLA crystal are elucidated from Fourier transform infrared spectroscopy study. UV–visible transmittance is recorded to study the optical transmittance range for the grown crystals. The powder second harmonic generation test confirms the nonlinear optical property of the grown crystals. From the microhardness test, the hardness of the grown crystals is estimated. The dielectric behaviour, such as the dielectric constant and the loss of the sample, are measured as a function of temperature and frequency. The ac conductivity of the grown crystals is also studied and the activation energy is calculated. (paper)

  17. EFFICIENT NANO-SCALE ADMIXTURE FOR FOAM STABILITY IMPROVEMENT OF CELLULAR CONCRETES

    Directory of Open Access Journals (Sweden)

    Grishina Аnna Nikolaevna

    2012-10-01

    Full Text Available The authors present their methodology of synthesis of a nano-scale additive designated for the stabilization of synthetic foaming agents. The nano-scale admixture is composed of iron hydroxide (III sol and aqueous sodium hydro silicates (water glass. Besides the above method, the topological structural model of the nano-scale additive is proposed. The additive stability was assessed upon its one-day storage (with the foaming agent added, and the assessment data are provided in the article. The authors have discovered that it is advisable to use an iron chloride solution in the concentration of 1 % to manufacture the iron hydroxide (III sol. The authors have also discovered that the rate of jellification goes up in the process of injecting the foaming agent into the foam that contains the nano-scale admixture developed by the authors. Dependence between the amount of sodium hydro silicate and the viscosity of the system composed of the water glass and the sol of iron hydroxide (III is examined in detail. The authors have identified that the average water glass viscosity curve demonstrates an extreme nature. The additive is used for the stabilization of the foam generated by synthetic foaming agents. The injection of the proposed additive improves foam stability. It is noteworthy that this positive result is free from any negative side effects.

  18. Basal entrainment by Newtonian gravity-driven flows

    Science.gov (United States)

    Bates, Belinda M.; Andreini, Nicolas; Ancey, Christophe

    2016-05-01

    Gravity-driven flows can erode the bed along which they descend and increase their mass by a factor of 10 or more. This process is called "basal entrainment." Although documented by field observations and laboratory experiments, it remains poorly understood. This paper examines what happens when a viscous gravity-driven flow generated by releasing a fixed volume of incompressible Newtonian fluid encounters a stationary layer (composed of fluid with the same density and viscosity). Models based on depth-averaged mass and momentum balance equations deal with bed-flow interfaces as shock waves. In contrast, we use an approach involving the long-wave approximation of the Navier-Stokes equations (lubrication theory), and in this context, bed-flow interfaces are acceleration waves that move quickly across thin stationary layers. The incoming flow digs down into the bed, pushing up downstream material, thus advancing the flow front. Extending the method used by Huppert ["The propagation of two-dimensional and axisymmetric viscous gravity currents over a rigid horizontal surface," J. Fluid Mech. 121, 43-58 (1982)] for modeling viscous dam-break waves, we end up with a nonlinear diffusion equation for the flow depth, which is solved numerically. Theory is compared with experimental results. Excellent agreement is found in the limit of low Reynolds numbers (i.e., for flow Reynolds numbers lower than 20) for the front position over time and flow depth profile.

  19. Kinematics of flow and sediment particles at entrainment and deposition

    Science.gov (United States)

    Antico, Federica; Sanches, Pedro; Aleixo, Rui; Ferreira, Rui M. L.

    2015-04-01

    A cohesionless granular bed subjected to a turbulent open-channel flow is analysed. The key objective is to clarify the kinematics of entrainment and deposition of individual sediment particles. In particular, we quantify a) the turbulent flow field in the vicinity of particles at the instants of their entrainment and of their deposition; b) the initial particle velocity and the particle velocity immediately before returning to rest. The experimental work was performed at the Hydraulics Laboratory of IST-UL in a 12.5 m long, 0.405 m wide glass-walled flume recirculating water and sediment through independent circuits. The granular bed was a 4.0 m long and 2.5 cm deep reach filled with 5 mm diameter glass beads packed (with some vibration) to a void fraction of 0.356, typical of random packing. Upstream the mobile bed reach the bed was composed of glued particles to ensure the development of a boundary layer with the same roughness. Laboratory tests were run under conditions of weak beadload transport with Shields parameters in the range 0.007 to 0.03. Froude numbers ranged from 0.63 to 0.95 while boundary Reynolds numbers were in the range 130 to 300. It was observed that the bed featured patches of regular arrangements: face centered cubic (fcc) or hexagonal close packing (hcp) blocks alternate with and body centered cubic (bcc) blocks. The resulting bed surface exhibits cleavage lines between blocks and there are spatial variations of bed elevation. The option for artificial sediment allowed for a simplified description of particle positioning at the instant of entrainment. In particular support and pivoting angles are found analytically. Skin friction angles were determind experimentally. The only relevant variables are exposure (defined as the ratio of the actual frontal projection of the exposed area to the area of a circle with 5 mm diameter) and protrusion (defined as the vertical distance between the apex of the particle and the mean local bed elevation

  20. Colour as a signal for entraining the mammalian circadian clock.

    Directory of Open Access Journals (Sweden)

    Lauren Walmsley

    2015-04-01

    Full Text Available Twilight is characterised by changes in both quantity ("irradiance" and quality ("colour" of light. Animals use the variation in irradiance to adjust their internal circadian clocks, aligning their behaviour and physiology with the solar cycle. However, it is currently unknown whether changes in colour also contribute to this entrainment process. Using environmental measurements, we show here that mammalian blue-yellow colour discrimination provides a more reliable method of tracking twilight progression than simply measuring irradiance. We next use electrophysiological recordings to demonstrate that neurons in the mouse suprachiasmatic circadian clock display the cone-dependent spectral opponency required to make use of this information. Thus, our data show that some clock neurons are highly sensitive to changes in spectral composition occurring over twilight and that this input dictates their response to changes in irradiance. Finally, using mice housed under photoperiods with simulated dawn/dusk transitions, we confirm that spectral changes occurring during twilight are required for appropriate circadian alignment under natural conditions. Together, these data reveal a new sensory mechanism for telling time of day that would be available to any mammalian species capable of chromatic vision.

  1. Changes in music tempo entrain movement related brain activity.

    Science.gov (United States)

    Daly, Ian; Hallowell, James; Hwang, Faustina; Kirke, Alexis; Malik, Asad; Roesch, Etienne; Weaver, James; Williams, Duncan; Miranda, Eduardo; Nasuto, Slawomir J

    2014-01-01

    The neural mechanisms of music listening and appreciation are not yet completely understood. Based on the apparent relationship between the beats per minute (tempo) of music and the desire to move (for example feet tapping) induced while listening to that music it is hypothesised that musical tempo may evoke movement related activity in the brain. Participants are instructed to listen, without moving, to a large range of musical pieces spanning a range of styles and tempos during an electroencephalogram (EEG) experiment. Event-related desynchronisation (ERD) in the EEG is observed to correlate significantly with the variance of the tempo of the musical stimuli. This suggests that the dynamics of the beat of the music may induce movement related brain activity in the motor cortex. Furthermore, significant correlations are observed between EEG activity in the alpha band over the motor cortex and the bandpower of the music in the same frequency band over time. This relationship is observed to correlate with the strength of the ERD, suggesting entrainment of motor cortical activity relates to increased ERD strength. PMID:25571015

  2. Engine jet entrainment in the near field of an aircraft

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, F.; Jacquin, L.; Laverdant, A. [Office National d`Etudes et de Recherches Aerospatiales (ONERA), 92 - Chatillon (France)

    1997-12-31

    A simplified approach has been applied to analyse the mixing and entrainment processes of the engine exhaust through their interaction with the vortex wake of an aircraft. These investigations are focused on the near filed, extending from exit nozzle to the beginning of the vortex phase (i.e. to about twenty seconds after the wake is generated). This study is performed using an integral model and a numerical simulation for a two-engine large civil aircraft. The properties of the wing-tip vortices on the calculation of the dilution ratio (defined as a tracer concentration) have been shown. The mixing process is also affected by the buoyancy effect, but only after the jet regime, when the trapping in the vortex core has occurred. Qualitative comparison with contrail photography shows similar features. Finally the distortion and stretching of the plume streamlines inside the vortices can be observed, and the role of the descent of the vortices on the maximum tracer concentration has been discussed. (author) 19 refs.

  3. Heat transfer effect of entrained gas in liquid sodium systems

    International Nuclear Information System (INIS)

    An analysis was made and a correlation developed to determine the reduction in heat transfer caused by entrained inert gas in sodium-cooled liquid metal systems. A 1% void fraction (1.62% volumetric flow rate of inert gas) is calculated to reduce the heat transfer coefficient by approximately 4% in a typical LMFBR. This reduction will not occur over the entire reactor, but only near the inlet of the radial blanket. It was concluded that a reduction in heat transfer in a system having a low oxygen concentration (0C (10000F), if the Reynolds number is greater than approximately 105, and if the operating time is longer than that required for complete wetting at the reference temperature, no reduction in heat transfer is expected. The cause of the reduction in heat transfer is postulated to be a reduction in the thermal conductivity of a two-phase sodium-gas lay er near the heated surface. It is proposed to calculate the thermal conductivity reduction using the average inert gas void fraction and a sintered-metal model. (Auth.)

  4. A review of the interference of carbon containing fly ash with air entrainment in concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard; Jensen, Anker Degn; Skjøth-Rasmussen, Martin Skov;

    2008-01-01

    Industrial utilization of fly ash from pulverized coal combustion plays an important role in environmentally clean and cost effective power generation. Today, the primary market for fly ash utilization is as pozzolanic additive in the production of concrete. However, the residual carbon in fly ash...... work carried out to identify the mechanisms causing the interactions between AEAs and fly ash in concrete mixtures, emphasizing the residual carbon. It has been shown that not only the amount, but also the properties of carbon, such as particle size and surface chemistry, has an impact on the......-treatment methods applied to improve fly ash quality are described in the review. Ozonation, thermal treatment and physical cleaning of carbon have been found to improve the fly ash performance for concrete utilization. Ultimately, recommendations for further work are outlined in the discussion....

  5. Turbulent flow field and air entrainment in laboratory plunging breaking waves

    Science.gov (United States)

    Na, Byoungjoon; Chang, Kuang-An; Huang, Zhi-Cheng; Lim, Ho-Joon

    2016-05-01

    This paper presents laboratory measurements of turbulent flow fields and void fraction in deep-water plunging breaking waves using imaging and optical fiber techniques. Bubble-size distributions are also determined based on combined measurements of velocity and bubble residence time. The most excited mode of the local intermittency measure of the turbulent flow and its corresponding length scale are obtained using a wavelet-based method and found to correlate with the swirling strength and vorticity. Concentrated vortical structures with high intermittency are observed near the lower boundaries of the aerated rollers where the velocity shear is high; the length scale of the deduced eddies ranges from 0.05 to 0.15 times the wave height. The number of bubbles with a chord length less than 2 mm demonstrates good correlation with the swirling strength. The power-law scaling and the Hinze scale of the bubbles determined from the bubble chord length distribution compare favorably with existing measurements. The turbulent dissipation rate, accounting for void fraction, is estimated using mixture theory. When void fraction is not considered, the turbulent dissipation rate is underestimated by more than 70% in the initial impinging and the first splash-up roller. A significant discrepancy of approximately 67% between the total energy dissipation rate and the turbulence dissipation rate is found. Of this uncounted dissipation, 23% is caused by bubble-induced dissipation.

  6. Experimental investigation on the droplet entrainment from interfacial waves in air-water horizontal stratified flow

    International Nuclear Information System (INIS)

    The main purpose of the wire is to avoid collision between adjacent rods.. Furthermore, a vortex induced vibration can be mitigated by wire spacers. In this study, the RANS based CFD methodology using an innovative grid generation has been evaluated in the 7-pin, 37-pin, and 217-pin wire wrapped fuel assembly, which is using the general purpose commercial CFD code, CFX. The RANS-based CFD methodology using the innovative hexagonal grid generation with the in-house code and the GGI function of the CFX code has been evaluated in the 7-pin, 37-pin, and 217-pin wire wrapped fuel assembly. SFR (Sodium-cooled Fast Reactor) system is one of the nuclear reactors in which a recycling of transuranics (TRUs) by reusing spent nuclear fuel sustains the fission chain reaction. This situation strongly motivated Korea Atomic Energy Research Institute (KAERI) to start a Prototype Gen Sodium-cooled Fast Reactor (PGSFR) design project under the national nuclear R and D program. Generally, SFR system has tight package of the fuel bundle and the high power density. The fuel assembly of SFR system is consisted of wire wrapped fuel bundles with triangular loose array. The bundles of the SFR fuel assembly usually consisted of rods and wire spacers. The innovative RANS-based CFD methodology can remarkably reduce the number of meshes. Grid sensitivity study of the wall y grid scale with SST turbulence model in 7-pin fuel assembly has been carried out, and the uncertainty of friction factor was under the 6.0%. It has been validated that the GGI function of CFX code is very conservative interpolation function. The innovative RANS based CFD methodology can be successfully extended to real 217- pin wire-wrapped fuel assembly of KAERI 2014 PGSFR

  7. Entrainment of Ambient Air into H2O/ArDC Arc Plasma Jet

    Czech Academy of Sciences Publication Activity Database

    Kavka, Tetyana; Hrabovský, Milan; Konrád, Miloš; Kopecký, Vladimír; Sember, Viktor

    Bari : Department of Chemistry, University of Bari, 2003 - (d'Agostino, R.; Favia, P.; Fracassi, F.; Palumbo, F.). s. 99 [International Symposium on Plasma Chemistry/16th./. 22.06.2003-27.06.2003, Taormina] Institutional research plan: CEZ:AV0Z2043910 Keywords : plasma jet, thermal plasma Subject RIV: BL - Plasma and Gas Discharge Physics

  8. Dependence of entrainment in shallow cumulus convection on vertical velocity and distance to cloud edge

    Science.gov (United States)

    Tian, Yang; Kuang, Zhiming

    2016-04-01

    The dependence of entrainment rate on environmental conditions and cloud characteristics is investigated using large eddy simulations (LES) of the response of shallow cumulus convection to a small-amplitude temperature perturbation that is horizontally uniform and localized in height. The simulated cumulus fields are analyzed in the framework of an ensemble of entraining plumes by tracking a large number of Lagrangian parcels embedded in the LES and grouping them into different plumes based on their detrainment heights. The results show that fractional entrainment rate per unit height of a plume is inversely proportional to the plume's vertical velocity and its distance to the cloud edge, while changes in environmental stratification and relative humidity, the plume's buoyancy, or the vertical gradient of its buoyancy due to the temperature perturbation have little effect on the plume's entrainment rate.

  9. Individual Differences in Rhythmic Cortical Entrainment Correlate with Predictive Behavior in Sensorimotor Synchronization.

    Science.gov (United States)

    Nozaradan, Sylvie; Peretz, Isabelle; Keller, Peter E

    2016-01-01

    The current study aims at characterizing the mechanisms that allow humans to entrain the mind and body to incoming rhythmic sensory inputs in real time. We addressed this unresolved issue by examining the relationship between covert neural processes and overt behavior in the context of musical rhythm. We measured temporal prediction abilities, sensorimotor synchronization accuracy and neural entrainment to auditory rhythms as captured using an EEG frequency-tagging approach. Importantly, movement synchronization accuracy with a rhythmic beat could be explained by the amplitude of neural activity selectively locked with the beat period when listening to the rhythmic inputs. Furthermore, stronger endogenous neural entrainment at the beat frequency was associated with superior temporal prediction abilities. Together, these results reveal a direct link between cortical and behavioral measures of rhythmic entrainment, thus providing evidence that frequency-tagged brain activity has functional relevance for beat perception and synchronization. PMID:26847160

  10. REGSOLexpert: Entrainer Selection Tool for waste solvent recovery by batch distillation processes

    OpenAIRE

    Rodriguez-Donis, Ivonne; Gerbaud, Vincent; Baudouin, Olivier; Joulia, Xavier

    2009-01-01

    A general procedure to systematize the search of several alternatives enabling the separation of non-ideal binary mixtures such as pressure-swing distillation, azeotropic and extractive distillation is presented. The use of heterogeneous entrainers is specially highlighted.

  11. A Lagrangian, small-scale investigation of turbulent entrainment in an axisymmetric jet

    International Nuclear Information System (INIS)

    Particle tracking velocimetry (PTV) was applied to study turbulent entrainment in an axisymmetric jet at Re = 5000. Several single-point flow statistics are used to characterize the general flow field of our newly designed jet facility, proving that a self-preserving axisymmetric jet could be established. An analysis of the Lagrangian evolution of small scale quantities, such as vorticity and strain, along trajectories passing the entrainment interface is performed. We find that a particle needs on the order of one Kolmogorov time scale to cross the entrainment interface, which is similar to results of grid turbulence without mean shear. Finally, we perform a conditional investigation of invariants of dui/duj at the entrainment interface, analyzing joint probability density functions (joint PDFs) evaluated at different times along trajectories crossing the interfacial region.

  12. Miniature Sample Collection and Delivery System using Gas-Entrained Powder Transport Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose to develop a miniature system for acquisition and delivery of solid samples to landed planetary instruments. This system would entrain powder produced by...

  13. Strong effects of network architecture in the entrainment of coupled oscillator systems

    Science.gov (United States)

    Kori, Hiroshi; Mikhailov, Alexander S.

    2006-12-01

    Random networks of coupled phase oscillators, representing an approximation for systems of coupled limit-cycle oscillators, are considered. Entrainment of such networks by periodic external forcing applied to a subset of their elements is numerically and analytically investigated. For a large class of interaction functions, we find that the entrainment window with a tongue shape becomes exponentially narrow for networks with higher hierarchical organization. However, the entrainment is significantly facilitated if the networks are directionally biased—i.e., closer to the feedforward networks. Furthermore, we show that the networks with high entrainment ability can be constructed by evolutionary optimization processes. The neural network structure of the master clock of the circadian rhythm in mammals is discussed from the viewpoint of our results.

  14. Fidelity of frequency and phase entrainment of circuit-level spike activity during DBS.

    Science.gov (United States)

    Agnesi, Filippo; Muralidharan, Abirami; Baker, Kenneth B; Vitek, Jerrold L; Johnson, Matthew D

    2015-08-01

    High-frequency stimulation is known to entrain spike activity downstream and upstream of several clinical deep brain stimulation (DBS) targets, including the cerebellar-receiving area of thalamus (VPLo), subthalamic nucleus (STN), and globus pallidus (GP). Less understood are the fidelity of entrainment to each stimulus pulse, whether entrainment patterns are stationary over time, and how responses differ among DBS targets. In this study, three rhesus macaques were implanted with a single DBS lead in VPLo, STN, or GP. Single-unit spike activity was recorded in the resting state in motor cortex during VPLo DBS, in GP during STN DBS, and in STN and pallidal-receiving area of motor thalamus (VLo) during GP DBS. VPLo DBS induced time-locked spike activity in 25% (n = 15/61) of motor cortex cells, with entrained cells following 7.5 ± 7.4% of delivered pulses. STN DBS entrained spike activity in 26% (n = 8/27) of GP cells, which yielded time-locked spike activity for 8.7 ± 8.4% of stimulus pulses. GP DBS entrained 67% (n = 14/21) of STN cells and 32% (n = 19/59) of VLo cells, which showed a higher fraction of pulses effectively inhibiting spike activity (82.0 ± 9.6% and 86.1 ± 16.6%, respectively). Latency of phase-locked spike activity increased over time in motor cortex (58%, VPLo DBS) and to a lesser extent in GP (25%, STN DBS). In contrast, the initial inhibitory phase observed in VLo and STN during GP DBS remained stable following stimulation onset. Together, these data suggest that circuit-level entrainment is low-pass filtered during high-frequency stimulation, most notably for glutamatergic pathways. Moreover, phase entrainment is not stationary or consistent at the circuit level for all DBS targets. PMID:26084905

  15. Neural entrainment to rhythmically-presented auditory, visual and audio-visual speech in children

    Directory of Open Access Journals (Sweden)

    Alan James Power

    2012-07-01

    Full Text Available Auditory cortical oscillations have been proposed to play an important role in speech perception. It is suggested that the brain may take temporal ‘samples’ of information from the speech stream at different rates, phase-resetting ongoing oscillations so that they are aligned with similar frequency bands in the input (‘phase locking’. Information from these frequency bands is then bound together for speech perception. To date, there are no explorations of neural phase-locking and entrainment to speech input in children. However, it is clear from studies of language acquisition that infants use both visual speech information and auditory speech information in learning. In order to study neural entrainment to speech in typically-developing children, we use a rhythmic entrainment paradigm (underlying 2 Hz or delta rate based on repetition of the syllable ba, presented in either the auditory modality alone, the visual modality alone, or as auditory-visual speech (via a talking head. To ensure attention to the task, children aged 13 years were asked to press a button as fast as possible when the ba stimulus violated the rhythm for each stream type. Rhythmic violation depended on delaying the occurrence of a ba in the isochronous stream. Neural entrainment was demonstrated for all stream types, and individual differences in standardized measures of language processing were related to auditory entrainment at the theta rate. Further, there was significant modulation of the preferred phase of auditory entrainment in the theta band when visual speech cues were present, indicating cross-modal phase resetting. The rhythmic entrainment paradigm developed here offers a method for exploring individual differences in oscillatory phase locking during development. In particular, a method for assessing neural entrainment and cross-modal phase resetting would be useful for exploring developmental learning difficulties thought to involve temporal sampling

  16. Rev-erbα in the brain is essential for circadian food entrainment

    OpenAIRE

    Julien Delezie; Stéphanie Dumont; Cristina Sandu; Sophie Reibel; Paul Pevet; Etienne Challet

    2016-01-01

    Foraging is costly in terms of time and energy. An endogenous food-entrainable system allows anticipation of predictable changes of food resources in nature. Yet the molecular mechanism that controls food anticipation in mammals remains elusive. Here we report that deletion of the clock component Rev-erbα impairs food entrainment in mice. Rev-erbα global knockout (GKO) mice subjected to restricted feeding showed reduced elevations of locomotor activity and body temperature prior to mealtime, ...

  17. Entrainment of riparian gravel and cobbles in an alluvial reach of a regulated canyon river

    Science.gov (United States)

    Elliotp, J.G.; Hammack, L.A.

    2000-01-01

    Many canyon rivers have channels and riparian zones composed of alluvial materials and these reaches, dominated by fluvial processes, are sensitive to alterations in streamflow regime. Prior to reservoir construction in the mid-1960s, banks and bars in alluvial reaches of the Gunnison River in the Black Canyon National Monument, Colorado, USA, periodically were reworked and cleared of riparian vegetation by mainstem floods. Recent interest in maintaining near-natural conditions in the Black Canyon using reservoir releases has created a need to estimate sediment-entraining discharges for a variety of geomorphic surfaces composed of sediment ranging in size from gravel to small boulders. Sediment entrainment potential was studied at eight cross-sections in an alluvial reach of the Gunnison River in the Black Canyon in 1994 and 1995. A one-dimensional water-surface profile model was used to estimate water-surface elevations, flow depths, and hydraulic conditions on selected alluvial surfaces for discharges ranging from 57 to 570 m3/s. Onsite observations before and after a flood of 270 m3/s confirmed sediment entrainment on several surfaces inundated by the flood. Selective entrainment of all but the largest particle sizes on the surface occurred at some locations. Physical evidence of sediment entrainment, or absence of sediment entrainment, on inundated surfaces generally was consistent with critical shear stresses estimated with a dimensionless critical shear stress of 0.030. Sediment-entrainment potential over a range of discharges was summarized by the ratio of the local boundary shear stress to the critical shear stress for d50, given hydraulic geometry and sediment-size characteristics. Differing entrainment potential for similar geomorphic surfaces indicates that estimation of minimum streamflow requirements based on sediment mobility is site-specific and that there is no unique streamflow that will initiate movement of d50 at every geomorphically similar

  18. Global and local oscillatory entrainment of visual behavior across retinotopic space.

    Science.gov (United States)

    Sokoliuk, Rodika; VanRullen, Rufin

    2016-01-01

    Ongoing brain oscillations (7-10 Hz) modulate visual perception; in particular, their precise phase can predict target perception. Here, we employ this phase-dependence of perception in a psychophysical experiment to track spatial properties of entrained oscillations of visual perception across the visual field. Is this entrainment local, or a more global phenomenon? If the latter, does oscillatory phase synchronize over space, or vary with increasing distance from the oscillatory source? We presented a disc stimulus in the upper left quadrant, oscillating in luminance at different frequencies (individual alpha frequency (IAF), 5 Hz, and 15 Hz) to entrain an oscillation with specific frequency and spatial origin. Observers fixated centrally, while flash stimuli at perceptual threshold appeared at different positions and times with respect to the oscillating stimulus. IAF and 5 Hz luminance oscillations modulated detection performance at all tested positions, whereas at 15 Hz, the effect was weaker and less consistent. Furthermore, for IAF and 5 Hz entrainment, preferred phases for target detection differed significantly between spatial locations, suggesting "local" entrainment of detection performance next to the oscillatory source, whereas more distant target locations shared a "global" effect with a significantly different phase. This unexpected global component of entrainment is tentatively attributed to widespread connectivity from thalamic nuclei such as the pulvinar. PMID:27126642

  19. Effect of oxy-fuel combustion with steam addition on coal ignition and burnout in an entrained flow reactor

    International Nuclear Information System (INIS)

    The ignition temperature and burnout of a semi-anthracite and a high-volatile bituminous coal were studied under oxy-fuel combustion conditions in an entrained flow reactor (EFR). The results obtained under oxy-fuel atmospheres (21%O2-79%CO2, 30%O2-70% O2 and 35%O2-65%CO2) were compared with those attained in air. The replacement of CO2 by 5, 10 and 20% of steam in the oxy-fuel combustion atmospheres was also evaluated in order to study the wet recirculation of flue gas. For the 21%O2-79%CO2 atmosphere, the results indicated that the ignition temperature was higher and the coal burnout was lower than in air. However, when the O2 concentration was increased to 30 and 35% in the oxy-fuel combustion atmosphere, the ignition temperature was lower and coal burnout was improved in comparison with air conditions. On the other hand, an increase in ignition temperature and a worsening of the coal burnout was observed when steam was added to the oxy-fuel combustion atmospheres though no relevant differences between the different steam concentrations were detected. -- Highlights: → The ignition temperature and the burnout of two thermal coals under oxy-fuel combustion conditions were determined. → The effect of the wet recirculation of flue gas on combustion behaviour was evaluated. → Addition of steam caused a worsening of the ignition temperature and coal burnout.

  20. Limit on a right-handed admixture to the weak b→c current from semileptonic decays

    International Nuclear Information System (INIS)

    We determine an upper bound for a possible right-handed b→c quark current admixture in semileptonic B→Xcl-ν decays from a simultaneous fit to moments of the lepton-energy and hadronic-mass distribution measured as a function of the lower limit on the lepton energy, using data measured by the BABAR detector. The right-handed admixture is parametrized by a new parameter cR as coefficient of computed moments with right-handed quark current. For the standard-model part we use the prediction of the heavy-quark expansion up to order 1/mb3 and perturbative corrections and for the right-handed contribution only up to order 1/mb2 and perturbative corrections. We find cR'=0.05-0.50+0.33 in agreement with the standard-model prediction of zero. Additionally, we give a constraint on a possible right-handed admixture from exclusive decays, which is with a value of cR'=0.01±0.03 more restrictive than our value from the inclusive fit. The difference in |Vcb| between the inclusive and exclusive extraction is only slightly reduced when allowing for a right-handed admixture in the range of cR'=0.01±0.03.