Design chart of optimum current leads

International Nuclear Information System (INIS)

Ishibashi, K.; Katase, A.; Maechata, K.

1986-01-01

The heat flow through current leads is one of major heat losses in a superconducting magnet system. To reduce the heat flow, current leads have been optimized in a complex way by varying such quantities as conductor length, cross-sectional area, heat transfer coefficient and cooling perimeter. Therefore, this study is made to simplify the design procedure, and to explain the general characteristics of the current leads. A new combined parameter which takes turbulent flow into account is introduced in the present work to enable us to draw a useful design chart. This chart gives, to a wide variety of current leads, detailed information about the optimum design-viz. geometric dimensions, heat flow into liquid helium, and pressure drop of the cooling gas. Change of the cross-sectional area along the conductor may improve the current lead performance. The effects of this area change are examined in detail

Optimum design of band-gap beam structures

DEFF Research Database (Denmark)

Olhoff, Niels; Niu, Bin; Cheng, Gengdong

2012-01-01

The design of band-gap structures receives increasing attention for many applications in mitigation of undesirable vibration and noise emission levels. A band-gap structure usually consists of a periodic distribution of elastic materials or segments, where the propagation of waves is impeded...... or significantly suppressed for a range of external excitation frequencies. Maximization of the band-gap is therefore an obvious objective for optimum design. This problem is sometimes formulated by optimizing a parameterized design model which assumes multiple periodicity in the design. However, it is shown...... in the present paper that such an a priori assumption is not necessary since, in general, just the maximization of the gap between two consecutive natural frequencies leads to significant design periodicity. The aim of this paper is to maximize frequency gaps by shape optimization of transversely vibrating...

A first course in optimum design of yacht sails

Science.gov (United States)

Sugimoto, Takeshi

1993-03-01

The optimum sail geometry is analytically obtained for the case of maximizing the thrust under equality and inequality constraints on the lift and the heeling moment. A single mainsail is assumed to be set close-hauled in uniform wind and upright on the flat sea surface. The governing parameters are the mast height and the gap between the sail foot and the sea surface. The lifting line theory is applied to analyze the aerodynamic forces acting on a sail. The design method consists of the variational principle and a feasibility study. Almost triangular sails are found to be optimum. Their advantages are discussed.

Optimum Design of Heat Exchangers Networks Part -I: Software Development

International Nuclear Information System (INIS)

Gabr, E.M.A.; EI-Temtamy, S.A.; Deriasl, S.F.; Moustafa, H.A.

2004-01-01

In this paper, we have developed a computerized framework for Heat Exchanger Network Synthesis (HENS) with optimality conditions of achieving the least operating and capital cost. The framework of HEN design involves the development three-computer programs, which applied sequentially to design an optimum HEN. The first program Automatic Minimum Utilities [AMU] developed for automatic formulation of LP equations, these equations can be solved by the optimization software [LINDO] to predict minimum hot and cold utilities. The second program based on Vertical Heat Transfer Method [VHTM] for predicting minimum overall heat transfer area and defining the optimum δbT m in. The third program [Mod.RESHEX] developed for targeting of heat transfer area and automatic synthesis of HEN. This program represents the modifications and development of RESHEX method to overcome the design defects, which appeared on original RESHEX applications

Planning of optimum production from a natural gas field

Energy Technology Data Exchange (ETDEWEB)

Van Dam, J

1968-03-01

The design of an optimum development plan for a natural gas field always depends on the typical characteristics of the producing field, as well as those of the market to be served by this field. Therefore, a good knowledge of the field parameters, such as the total natural gas reserves, the well productivity, and the dependence of production rates on pipeline pressure and depletion of natural gas reserves, is required prior to designing the development scheme of the field, which in fact depends on the gas-sales contract to be concluded in order to commit the natural gas reserves to the market. In this paper these various technical parameters are discussed in some detail, and on this basis a theoretical/economical analysis of natural gas production is given. For this purpose a simplified economical/mathematical model for the field is proposed, from which optimum production rates at various future dates can be calculated. The results of these calculations are represented in a dimensionless diagram which may serve as an aid in designing optimum development plans for a natural gas field. The use of these graphs is illustrated in a few examples.

Optimum Design of LLC Resonant Converter using Inductance Ratio (Lm/Lr)

Science.gov (United States)

Palle, Kowstubha; Krishnaveni, K.; Ramesh Reddy, Kolli

2017-06-01

The main benefits of LLC resonant dc/dc converter over conventional series and parallel resonant converters are its light load regulation, less circulating currents, larger bandwidth for zero voltage switching, and less tuning of switching frequency for controlled output. An unique analytical tool, called fundamental harmonic approximation with peak gain adjustment is used for designing the converter. In this paper, an optimum design of the converter is proposed by considering three different design criterions with different values of inductance ratio (Lm/Lr) to achieve good efficiency at high input voltage. The optimum design includes the analysis in operating range, switching frequency range, primary side losses of a switch and stability. The analysis is carried out with simulation using the software tools like MATLAB and PSIM. The performance of the optimized design is demonstrated for a design specification of 12 V, 5 A output operating with an input voltage range of 300-400 V using FSFR 2100 IC of Texas instruments.

Applicability Problem in Optimum Reinforced Concrete Structures Design

Directory of Open Access Journals (Sweden)

Ashara Assedeq

2016-01-01

Full Text Available Optimum reinforced concrete structures design is very complex problem, not only considering exactness of calculus but also because of questionable applicability of existing methods in practice. This paper presents the main theoretical mathematical and physical features of the problem formulation as well as the review and analysis of existing methods and solutions considering their exactness and applicability.

On the optimum signal constellation design for high-speed optical transport networks.

Science.gov (United States)

Liu, Tao; Djordjevic, Ivan B

2012-08-27

In this paper, we first describe an optimum signal constellation design algorithm, which is optimum in MMSE-sense, called MMSE-OSCD, for channel capacity achieving source distribution. Secondly, we introduce a feedback channel capacity inspired optimum signal constellation design (FCC-OSCD) to further improve the performance of MMSE-OSCD, inspired by the fact that feedback channel capacity is higher than that of systems without feedback. The constellations obtained by FCC-OSCD are, however, OSNR dependent. The optimization is jointly performed together with regular quasi-cyclic low-density parity-check (LDPC) code design. Such obtained coded-modulation scheme, in combination with polarization-multiplexing, is suitable as both 400 Gb/s and multi-Tb/s optical transport enabling technology. Using large girth LDPC code, we demonstrate by Monte Carlo simulations that a 32-ary signal constellation, obtained by FCC-OSCD, outperforms previously proposed optimized 32-ary CIPQ signal constellation by 0.8 dB at BER of 10(-7). On the other hand, the LDPC-coded 16-ary FCC-OSCD outperforms 16-QAM by 1.15 dB at the same BER.

Designing and testing the optimum design of automotive air-to-air thermoelectric air conditioner (TEAC) system

International Nuclear Information System (INIS)

Attar, Alaa; Lee, HoSung

2016-01-01

Highlights: • The optimum design of automotive thermoelectric AC system is proposed. • It is optimized by combining the thermal isolation and the dimensionless methods. • An experiment is conducted to validate the analytical design. - Abstract: The current project is discussing the optimization of counter flow air-to-air thermoelectric air conditioners (TEAC) system. Previous work showed an analytical model with experimental validation of a unit cell of TEAC system. However, the focus of this work is to simulate the optimum design of a whole TEAC system from given inlet parameters (i.e., hot and cold air mass flow rates and ambient temperatures). The analytical model was built by combining an optimal design method with dimensional analysis, which was recently developed, and the thermal isolation method in order to optimize the thermoelectric parameters (i.e., electrical current supplied and the number of thermocouples or the geometric factor, simultaneously). Moreover, based on the designed model, an experiment was conducted in order to study the accuracy of the analytical model. Even though the analytical model was built based on the thermoelectric ideal equations, it shows a good agreement with the experiment. This agreement was mainly a result of the use of the thermoelectric effective material properties which are obtained from the measured maximum thermoelectric module parameters. Since the experiment validate the analytical model, this model provides uncomplicated method to study the optimum design at given inputs.

Optimum Design of Multi-Function Robot Arm Gripper for Varying Shape Green Product

Directory of Open Access Journals (Sweden)

Razali Zol Bahri

2016-01-01

Full Text Available The project focuses on thorough experimentally studies of the optimum design of Multi-function Robot Arm Gripper for varying shape green product. The purpose of this project is to design a few of robot arm gripper for multi-functionally grip a green product with varying shape. The main character of the gripper is that it can automated adjust its finger to suit with the shape of the product. An optimum design of multi-function robot arm gripper is verified through experimental study. The expected result is a series of analytical results on the proposal of gripper design and material that will be selected for the gripper. The analysis of the gripper design proposal by using ANSYS and CATIA software is described in detail in this paper.

Challenges in IC design for hearing aids

DEFF Research Database (Denmark)

Jørgensen, Ivan Harald Holger

2012-01-01

Designing modern hearing aids is a formidable challenge. The size of hearing aids is constantly decreasing, making them virtually invisible today. Still, as in all other modern electronics, more and more features are added to these devices driven by the development in modern IC technology....... The demands for performance and features at very low supply voltage and power consumption constantly prove a challenge to the physical design of hearing aids and not at least the design of the ICs for these. As a result of this all large hearing aid manufacturers use fully customized ASICs in their products...... to produce a competitive advantage. This presentation will give a brief insight into the hearing aid market and industry, a brief view of the historic development of hearing aids and an introduction to how a modern hearing is constructed showing the amplifier as the key component in the modern hearing aid...

Optimum design for 12 MeV linear induction accelerator diode

International Nuclear Information System (INIS)

Yu Haijun; Shi Jinshui; Li Qin; He Guorong; Ma Bing; Wang Jingsheng; Wang Liping

2001-01-01

A series of optimization designs of electron diode in 12 Mev linear induction accelerator are studied by using numerical simulation code MAGIC and experiment method in order to improve the electron beam quality. MAGIC code solves the Maxwell equations in the presence of charged particle, electron field distribution on cathode surface which influences electron emission is given, the optimum diode is obtained by comparing the results of experiment in 12 MeV linear induction accelerator. The author also gives SEM analysis and experiment comparison of velvet emission. Finally, emitted current I e = 8.52 kA, beam current I 8 ≥ 3.0 kA, targeted current I 0 ≥ 2.30 kA with optimum diode are obtained

Design an optimum safety policy for personnel safety management - A system dynamic approach

International Nuclear Information System (INIS)

Balaji, P.

2014-01-01

Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making

Design an optimum safety policy for personnel safety management - A system dynamic approach

Energy Technology Data Exchange (ETDEWEB)

Balaji, P. [The Glocal University, Mirzapur Pole, Delhi- Yamuntori Highway, Saharanpur 2470001 (India)

2014-10-06

Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making.

Design an optimum safety policy for personnel safety management - A system dynamic approach

Science.gov (United States)

Balaji, P.

2014-10-01

Personnel safety management (PSM) ensures that employee's work conditions are healthy and safe by various proactive and reactive approaches. Nowadays it is a complex phenomenon because of increasing dynamic nature of organisations which results in an increase of accidents. An important part of accident prevention is to understand the existing system properly and make safety strategies for that system. System dynamics modelling appears to be an appropriate methodology to explore and make strategy for PSM. Many system dynamics models of industrial systems have been built entirely for specific host firms. This thesis illustrates an alternative approach. The generic system dynamics model of Personnel safety management was developed and tested in a host firm. The model was undergone various structural, behavioural and policy tests. The utility and effectiveness of model was further explored through modelling a safety scenario. In order to create effective safety policy under resource constraint, DOE (Design of experiment) was used. DOE uses classic designs, namely, fractional factorials and central composite designs. It used to make second order regression equation which serve as an objective function. That function was optimized under budget constraint and optimum value used for safety policy which shown greatest improvement in overall PSM. The outcome of this research indicates that personnel safety management model has the capability for acting as instruction tool to improve understanding of safety management and also as an aid to policy making.

Optimum Design of a Coil Spring for Improving the Performance of a Spring -Operated Mechanism

International Nuclear Information System (INIS)

Lee, Dae Woo; Sohn, Jeong Hyun; Yoo, Wan Suk

2016-01-01

In this study, a release test bed is designed to evaluate the dynamic behaviors of a coil spring. From the release tests, the dynamic behaviors of a coil spring are analyzed. A lumped parameter spring model was established for numerical simulation of a spring. The design variables of a coil spring are optimized by using the design of experiments approach. Two-level factorial designs are used for the design optimization, and the primary effects of the design variables are analyzed. Based on the results of the interaction analysis and design sensitivity analysis, the level of the design variables is rearranged. Finally, the mixed-level factorial design is used for the optimum design process. According to the optimum design of the opening spring, the dynamic performance of the spring-operated mechanism increases by 2.90

Theoretical and numerical study of an optimum design algorithm

International Nuclear Information System (INIS)

Destuynder, Philippe.

1976-08-01

This work can be separated into two main parts. First, the behavior of the solution of an elliptic variational equation is analyzed when the domain is submitted to a small perturbation. The case of inequations is also considered. Secondly the previous results are used for deriving an optimum design algorithm. This algorithm was suggested by the center-method proposed by Huard. Numerical results show the superiority of the method on other different optimization techniques [fr

Optimum design of a nuclear heat supply

International Nuclear Information System (INIS)

Borel, J.P.

1984-01-01

This paper presents an economic analysis for the optimum design of a nuclear heat supply to a given district-heating network. First, a general description of the system is given, which includes a nuclear power plant, a heating power plant and a district-heating network. The heating power plant is fed with steam from the nuclear power plant. It is assumed that the heating network is already in operation and that the nuclear power plant was previously designed to supply electricity. Second, a technical definition of the heat production and transportation installations is given. The optimal power of these installations is examined. The main result is a relationship between the network capacity and the level of the nuclear heat supply as a substitute for oil under the best economic conditions. The analysis also presents information for choosing the best operating mode. Finally, the heating power plant is studied in more detail from the energy, technical and economic aspects. (author)

Optimum Assembly Sequence Planning System Using Discrete Artificial Bee Colony Algorithm

Directory of Open Access Journals (Sweden)

Özkan Özmen

2018-01-01

Full Text Available Assembly refers both to the process of combining parts to create a structure and to the product resulting therefrom. The complexity of this process increases with the number of pieces in the assembly. This paper presents the assembly planning system design (APSD program, a computer program developed based on a matrix-based approach and the discrete artificial bee colony (DABC algorithm, which determines the optimum assembly sequence among numerous feasible assembly sequences (FAS. Specifically, the assembly sequences of three-dimensional (3D parts prepared in the computer-aided design (CAD software AutoCAD are first coded using the matrix-based methodology and the resulting FAS are assessed and the optimum assembly sequence is selected according to the assembly time optimisation criterion using DABC. The results of comparison of the performance of the proposed method with other methods proposed in the literature verify its superiority in finding the sequence with the lowest overall time. Further, examination of the results of application of APSD to assemblies consisting of parts in different numbers and shapes shows that it can select the optimum sequence from among hundreds of FAS.

Multi-objective optimum design of fast tool servo based on improved differential evolution algorithm

International Nuclear Information System (INIS)

Zhu, Zhiwei; Zhou, Xiaoqin; Liu, Qiang; Zhao, Shaoxin

2011-01-01

The flexure-based mechanism is a promising realization of fast tool servo (FTS), and the optimum determination of flexure hinge parameters is one of the most important elements in the FTS design. This paper presents a multi-objective optimization approach to optimizing the dimension and position parameters of the flexure-based mechanism, which is based on the improved differential evolution algorithm embedding chaos and nonlinear simulated anneal algorithm. The results of optimum design show that the proposed algorithm has excellent performance and a well-balanced compromise is made between two conflicting objectives, the stroke and natural frequency of the FTS mechanism. The validation tests based on finite element analysis (FEA) show good agreement with the results obtained by using the proposed theoretical algorithm of this paper. Finally, a series of experimental tests are conducted to validate the design process and assess the performance of the FTS mechanism. The designed FTS reaches up to a stroke of 10.25 μm with at least 2 kHz bandwidth. Both of the FEA and experimental results demonstrate that the parameters of the flexure-based mechanism determined by the proposed approaches can achieve the specified performance and the proposed approach is suitable for the optimum design of FTS mechanism and of excellent performances

Integrated computer aided design simulation and manufacture

OpenAIRE

Diko, Faek

1989-01-01

Computer Aided Design (CAD) and Computer Aided Manufacture (CAM) have been investigated and developed since twenty years as standalone systems. A large number of very powerful but independent packages have been developed for Computer Aided Design,Aanlysis and Manufacture. However, in most cases these packages have poor facility for communicating with other packages. Recently attempts have been made to develop integrated CAD/CAM systems and many software companies a...

Computer aided design

International Nuclear Information System (INIS)

Barache, J.M.; Beltranda, G.; Blanc, P.

1987-01-01

In order to ensure that the data transmitted to the managment system is of the required quality and consistent with the general control command protocols, computer aided design (CAD) was employed for level N4. One describes the use of CAD for the control system of N4 [fr

Computer-aided design and computer science technology

Science.gov (United States)

Fulton, R. E.; Voigt, S. J.

1976-01-01

A description is presented of computer-aided design requirements and the resulting computer science advances needed to support aerospace design. The aerospace design environment is examined, taking into account problems of data handling and aspects of computer hardware and software. The interactive terminal is normally the primary interface between the computer system and the engineering designer. Attention is given to user aids, interactive design, interactive computations, the characteristics of design information, data management requirements, hardware advancements, and computer science developments.

Computer Aided Solvent Selection and Design Framework

DEFF Research Database (Denmark)

Mitrofanov, Igor; Conte, Elisa; Abildskov, Jens

and computer-aided tools and methods for property prediction and computer-aided molecular design (CAMD) principles. This framework is applicable for solvent selection and design in product design as well as process design. The first module of the framework is dedicated to the solvent selection and design...... in terms of: physical and chemical properties (solvent-pure properties); Environment, Health and Safety (EHS) characteristic (solvent-EHS properties); operational properties (solvent–solute properties). 3. Performing the search. The search step consists of two stages. The first is a generation and property...... identification of solvent candidates using special software ProCAMD and ProPred, which are the implementations of computer-aided molecular techniques. The second consists of assigning the RS-indices following the reaction–solvent and then consulting the known solvent database and identifying the set of solvents...

Computer Aided Drug Design: Success and Limitations.

Science.gov (United States)

Baig, Mohammad Hassan; Ahmad, Khurshid; Roy, Sudeep; Ashraf, Jalaluddin Mohammad; Adil, Mohd; Siddiqui, Mohammad Haris; Khan, Saif; Kamal, Mohammad Amjad; Provazník, Ivo; Choi, Inho

2016-01-01

Over the last few decades, computer-aided drug design has emerged as a powerful technique playing a crucial role in the development of new drug molecules. Structure-based drug design and ligand-based drug design are two methods commonly used in computer-aided drug design. In this article, we discuss the theory behind both methods, as well as their successful applications and limitations. To accomplish this, we reviewed structure based and ligand based virtual screening processes. Molecular dynamics simulation, which has become one of the most influential tool for prediction of the conformation of small molecules and changes in their conformation within the biological target, has also been taken into account. Finally, we discuss the principles and concepts of molecular docking, pharmacophores and other methods used in computer-aided drug design.

Analysis and Experimental Investigation of Optimum Design of Thermoelectric Cooling/Heating System for Car Seat Climate Control (CSCC)

Science.gov (United States)

Elarusi, Abdulmunaem; Attar, Alaa; Lee, HoSung

2018-02-01

The optimum design of a thermoelectric system for application in car seat climate control has been modeled and its performance evaluated experimentally. The optimum design of the thermoelectric device combining two heat exchangers was obtained by using a newly developed optimization method based on the dimensional technique. Based on the analytical optimum design results, commercial thermoelectric cooler and heat sinks were selected to design and construct the climate control heat pump. This work focuses on testing the system performance in both cooling and heating modes to ensure accurate analytical modeling. Although the analytical performance was calculated using the simple ideal thermoelectric equations with effective thermoelectric material properties, it showed very good agreement with experiment for most operating conditions.

Optimum design of nonimaging Fresnel lens; Hiketsuzo fureneru renzu no saiteki sekkei

Energy Technology Data Exchange (ETDEWEB)

Leutz, R.; Komai, K.; Akisawa, A.; Kashiwagi, T. [Tokyo University of Agriculture and Technology, Tokyo (Japan); Suzuki, A. [Unesco, Paris (France). Associations in Japan

1999-11-25

An optimum convex shaped nonimaging Fresnel lens is designed following the edge ray principle. The lens is evaluated by tracing rays and calculating a projective optical concentration ratio. This Fresnel lens can used as concentrator in photovoltaic and solar thermal applications. (author)

Optimum Safety Levels and Design Rules for the Icelandic Type Berm Breakwater

DEFF Research Database (Denmark)

Sigurdarson, Sigurdur; van der Meer, Jentsje W.; Burcharth, Hans F.

2007-01-01

Guidance on selection of breakwater types and related design safety levels for breakwaters are almost non-existent, which is the reason that PIANC has initiated working group 47 on this subject. This paper presents ongoing work particulary on the Icelandic type berm breakwater within the PIANC...... working group. It will concentrate on design guidance and on the optimum safety levels for this type of structure....

Intelligent Support for a Computer Aided Design Optimisation Cycle

OpenAIRE

B. Dolšak; M. Novak; J. Kaljun

2006-01-01

It is becoming more and more evident that  adding intelligence  to existing computer aids, such as computer aided design systems, can lead to significant improvements in the effective and reliable performance of various engineering tasks, including design optimisation. This paper presents three different intelligent modules to be applied within a computer aided design optimisation cycle to enable more intelligent and less experience-dependent design performance. 

Technoeconomical Assessment of Optimum Design for Photovoltaic Water Pumping System for Rural Area in Oman

Directory of Open Access Journals (Sweden)

Hussein A. Kazem

2015-01-01

Full Text Available Photovoltaic (PV systems have been used globally for a long time to supply electricity for water pumping system for irrigation. System cost drops down with time since PV technology, efficiency, and design methodology have been improved and cost of wattage drops dramatically in the last decade. In the present paper optimum PV system design for water pumping system has been proposed for Oman. Intuitive and numerical methods were used to design the system. HOMER software as a numerical method was used to design the system to come up with optimum design for Oman. Also, REPS.OM software has been used to find the optimum design based on hourly meteorological data. The daily solar energy in Sohar was found to be 6.182 kWh/m2·day. However, it is found that the system annual yield factor is 2024.66 kWh/kWp. Furthermore, the capacity factor was found to be 23.05%, which is promising. The cost of energy and system capital cost has been compared with that of diesel generator and systems in literature. The comparison shows that the cost of energy is 0.180, 0.309, and 0.790 USD/kWh for PV-REPS.OM, PV-HOMER, and diesel systems, respectively, which sound that PV water pumping systems are promising in Oman.

Design Aids for Real-Time Systems (DARTS)

Science.gov (United States)

Szulewski, P. A.

1982-01-01

Design-Aids for Real-Time Systems (DARTS) is a tool that assists in defining embedded computer systems through tree structured graphics, military standard documentation support, and various analyses including automated Software Science parameter counting and metrics calculation. These analyses provide both static and dynamic design quality feedback which can potentially aid in producing efficient, high quality software systems.

Multidisciplinary Aerodynamic Design of a Rotor Blade for an Optimum Rotor Speed Helicopter

Directory of Open Access Journals (Sweden)

Jiayi Xie

2017-06-01

Full Text Available The aerodynamic design of rotor blades is challenging, and is crucial for the development of helicopter technology. Previous aerodynamic optimizations that focused only on limited design points find it difficult to balance flight performance across the entire flight envelope. This study develops a global optimum envelope (GOE method for determining blade parameters—blade twist, taper ratio, tip sweep—for optimum rotor speed helicopters (ORS-helicopters, balancing performance improvements in hover and various freestream velocities. The GOE method implements aerodynamic blade design by a bi-level optimization, composed of a global optimization step and a secondary optimization step. Power loss as a measure of rotor performance is chosen as the objective function, referred to as direct power loss (DPL in this study. A rotorcraft comprehensive code for trim simulation with a prescribed wake method is developed. With the application of the GOE method, a DPL reduction of as high as 16.7% can be achieved in hover, and 24% at high freestream velocity.

A computer-aided molecular design framework for crystallization solvent design

DEFF Research Database (Denmark)

Karunanithi, Arunprakash T.; Achenie, Luke E.K.; Gani, Rafiqul

2006-01-01

One of the key decisions in designing solution crystallization processes is the selection of solvents. In this paper, we present a computer-aided molecular design (CAMD) framework for the design and selection of solvents and/or anti-solvents for solution crystallization. The CAMD problem is formu......One of the key decisions in designing solution crystallization processes is the selection of solvents. In this paper, we present a computer-aided molecular design (CAMD) framework for the design and selection of solvents and/or anti-solvents for solution crystallization. The CAMD problem...... solvent molecules. Solvent design and selection for two types of solution crystallization processes namely cooling crystallization and drowning out crystallization are presented. In the first case study, the design of single compound solvent for crystallization of ibuprofen, which is an important...

Designing from minimum to optimum functionality

Science.gov (United States)

Bannova, Olga; Bell, Larry

2011-04-01

This paper discusses a multifaceted strategy to link NASA Minimal Functionality Habitable Element (MFHE) requirements to a compatible growth plan; leading forward to evolutionary, deployable habitats including outpost development stages. The discussion begins by reviewing fundamental geometric features inherent in small scale, vertical and horizontal, pressurized module configuration options to characterize applicability to meet stringent MFHE constraints. A proposed scenario to incorporate a vertical core MFHE concept into an expanded architecture to provide continuity of structural form and a logical path from "minimum" to "optimum" design of a habitable module. The paper describes how habitation and logistics accommodations could be pre-integrated into a common Hab/Log Module that serves both habitation and logistics functions. This is offered as a means to reduce unnecessary redundant development costs and to avoid EVA-intensive on-site adaptation and retrofitting requirements for augmented crew capacity. An evolutionary version of the hard shell Hab/Log design would have an expandable middle section to afford larger living and working accommodations. In conclusion, the paper illustrates that a number of cargo missions referenced for NASA's 4.0.0 Lunar Campaign Scenario could be eliminated altogether to expedite progress and reduce budgets. The plan concludes with a vertical growth geometry that provides versatile and efficient site development opportunities using a combination of hard Hab/Log modules and a hybrid expandable "CLAM" (Crew Lunar Accommodations Module) element.

Optimum design of vaporizer fin with liquefied natural gas by numerical analysis

International Nuclear Information System (INIS)

Jeong, Hyo Min; Chung, Han Shik; Lee, Sang Chul; Kong, Tae Woo; Yi, Chung Seub

2006-01-01

Generally, the temperature drop under 0 .deg. C on vaporizer surface creates frozen dews. This problem seems to increase as the time progress and humidity rises. In addition, the frozen dews create frost deposition. Consequently, heat transfer on vaporizer decreases because frost deposition causes adiabatic condition. Therefore, it is very important to solve this problem. This paper aims to study of the optimum design of used vaporizer at local LNG station. In this paper, experimental results were compared with numerical results. Geometries of numerical and experimental vaporizers were identical. Studied parameters of vaporizer are angle between two fins (Φ) and fin thickness (TH F ). Numerical analysis results were presented through the correlations between the ice layer thickness (TH ICE ) on the vaporizer surface to the temperature distribution of inside vaporizer (T IN ), fin thickness (TH F ), and angle between two fins (Φ). Numerical result shows good agreement with experimental outcome. Finally, the correlations for optimum design of vaporizer are proposed on this paper

Optimum design of a coded mask X-ray telescope for rocket applications

International Nuclear Information System (INIS)

Gunson, J.; Polychronopulos, B.

1976-01-01

A review of the principles of current X-ray telescopes is made with particular emphasis on two-step imaging techniques involving coding masks. The merits and limitations of the various types of coding masks in use are examined in detail. The limitations are shown to arise from the finite nature of practical masks. By postulating periodicity, 'optimum masks' can be constructed with ideal imaging qualities. The theory for the design of such masks and the practical considerations involved in the design of a rocket-borne X-ray telescope system are discussed in full, with particular attention paid to resolution, field of view and image noise. The main emphasis throughout the paper is on one-dimensional masks but two-dimensional masks are also studied. It is concluded that optimum masks could prove very valuable in astronomical applications and also in other fields such as radiography, where high imaging quality coupled with high sensitivity and low cost are of utmost importance. (author)

New design methods for computer aided architecturald design methodology teaching

NARCIS (Netherlands)

Achten, H.H.

2003-01-01

Architects and architectural students are exploring new ways of design using Computer Aided Architectural Design software. This exploration is seldom backed up from a design methodological viewpoint. In this paper, a design methodological framework for reflection on innovate design processes by

Roots of Performance - Aided Design in Utzon´s design principles

DEFF Research Database (Denmark)

Parigi, Dario

2014-01-01

on paper, to an evolving paradigm where the increasing integration of parametric tools, performative analysis and computational methods is changing the way we learn and design. Its constitutive factors are: 1) embedded tectonics, 2) performance simulation 3) computational methods.......This paper discuss an emerging paradigm here identified as PAD, acronym of Performance-Aided Design, that aims at embracing complexity in the design process, and tackling it with digital tools. Computer Aided Design tools are gradually shifting from the mere translation of the work once carried...

Computer aided optimum design of rubble-mound breakwater cross-sections : Manual of the RUMBA computer package, release 1

NARCIS (Netherlands)

De Haan, W.

1989-01-01

The computation of the optimum rubble-mound breakwater crosssection is executed on a micro-computer. The RUMBA computer package consists of two main parts: the optimization process is executed by a Turbo Pascal programme, the second part consists of editing functions written in AutoLISP. AutoLISP is

Optimum design of cogeneration system for nuclear seawater desalination - 15272

International Nuclear Information System (INIS)

Jung, Y.H.; Jeong, Y.H.

2015-01-01

A nuclear desalination process, which uses the energy released by nuclear fission, has less environmental impact and is generally cost-competitive with a fossil-fuel desalination process. A reference cogeneration system focused on in this study is the APR-1400 coupled with a MED (multi-effect distillation) process using the thermal vapor compression (TVC) technology. The thermal condition of the heat source is the most crucial factor that determines the desalination performance, i.e. energy consumption or freshwater production, of the MED-TVC process. The MED-TVC process operating at a higher motive steam pressure clearly shows a higher desalination performance. However, this increased performance does not necessarily translate to an advantage over processes operated at lower motive steam pressures. For instance, a higher motive steam pressure will increase the heat cost resulting from larger electricity generation loss, and thus may make this process unfavorable from an economic point of view. Therefore, there exists an optimum design point in the coupling configuration that makes the nuclear cogeneration system the most economical. This study is mainly aimed at investigating this optimum coupling design point of the reference nuclear cogeneration system using corresponding analysis tools. The following tools are used: MEE developed by the MEDRC for desalination performance analysis of the MED-TVC process, DE-TOP and DEEP developed by the IAEA for modeling of coupling configuration and economic evaluation of the nuclear cogeneration system, respectively. The results indicate that steam extraction from the MS exhaust and condensate return to HP FWHTR 5 is the most economical coupling design

Optimum Design of Braced Steel Space Frames including Soil-Structure Interaction via Teaching-Learning-Based Optimization and Harmony Search Algorithms

Directory of Open Access Journals (Sweden)

Ayse T. Daloglu

2018-01-01

Full Text Available Optimum design of braced steel space frames including soil-structure interaction is studied by using harmony search (HS and teaching-learning-based optimization (TLBO algorithms. A three-parameter elastic foundation model is used to incorporate the soil-structure interaction effect. A 10-storey braced steel space frame example taken from literature is investigated according to four different bracing types for the cases with/without soil-structure interaction. X, V, Z, and eccentric V-shaped bracing types are considered in the study. Optimum solutions of examples are carried out by a computer program coded in MATLAB interacting with SAP2000-OAPI for two-way data exchange. The stress constraints according to AISC-ASD (American Institute of Steel Construction-Allowable Stress Design, maximum lateral displacement constraints, interstorey drift constraints, and beam-to-column connection constraints are taken into consideration in the optimum design process. The parameters of the foundation model are calculated depending on soil surface displacements by using an iterative approach. The results obtained in the study show that bracing types and soil-structure interaction play very important roles in the optimum design of steel space frames. Finally, the techniques used in the optimum design seem to be quite suitable for practical applications.

Computer aided design for the nuclear industry

International Nuclear Information System (INIS)

Basson, Keith

1986-01-01

The paper concerns the new computer aided design (CAD) centre for the United Kingdom nuclear industry, and its applications. A description of the CAD system is given, including the current projects at the CAD centre. Typical applications of the 3D CAD plant based models, stress analysis studies, and the extraction of data from CAD drawings to produce associated documentation, are all described. Future developments using computer aided design systems are also considered. (U.K.)

Optimum Design of FGX-CNT-Reinforced Reddy Pipes Conveying Fluid Subjected to Moving Load

Directory of Open Access Journals (Sweden)

Farid Vakili Tahami

2016-12-01

Full Text Available The harmony search algorithm is applied to the optimum designs of functionally graded (FG-carbon nanotubes (CNTs-reinforced pipes conveying fluid which are subjected to a moving load. The structure is modeled by the Reddy cylindrical shell theory, and the motion equations are derived by Hamilton's principle. The dynamic displacement of the system is derived based on the differential quadrature method (DQM. Moreover, the length, thickness, diameter, velocity, and acceleration of the load, the temperature and velocity of the fluid, and the volume fraction of CNT are considered for the design variables. The results illustrate that the optimum diameter of the pipe is decreased by increasing the volume percentage of CNTs. In addition, by increasing the moving load velocity and acceleration, the FS is decreased.

Software For Computer-Aided Design Of Control Systems

Science.gov (United States)

Wette, Matthew

1994-01-01

Computer Aided Engineering System (CAESY) software developed to provide means to evaluate methods for dealing with users' needs in computer-aided design of control systems. Interpreter program for performing engineering calculations. Incorporates features of both Ada and MATLAB. Designed to be flexible and powerful. Includes internally defined functions, procedures and provides for definition of functions and procedures by user. Written in C language.

Optimum design for rotor-bearing system using advanced generic algorithm

International Nuclear Information System (INIS)

Kim, Young Chan; Choi, Seong Pil; Yang, Bo Suk

2001-01-01

This paper describes a combinational method to compute the global and local solutions of optimization problems. The present hybrid algorithm uses both a generic algorithm and a local concentrate search algorithm (e.g simplex method). The hybrid algorithm is not only faster than the standard genetic algorithm but also supplies a more accurate solution. In addition, this algorithm can find the global and local optimum solutions. The present algorithm can be supplied to minimize the resonance response (Q factor) and to yield the critical speeds as far from the operating speed as possible. These factors play very important roles in designing a rotor-bearing system under the dynamic behavior constraint. In the present work, the shaft diameter, the bearing length, and clearance are used as the design variables

On Optimum Safety Levels of Breakwaters

DEFF Research Database (Denmark)

Burcharth, Hans F.; Sørensen, John Dalsgaard

2006-01-01

The paper presents results from numerical simulations performed with the objective of identifying optimum design safety levels of conventional rubble mound and caisson breakwaters, corresponding to the lowest costs over the service life of the structures. The work is related to the PIANC Working...... Group 47 on "Selection of type of breakwater structures". The paper summaries results given in Burcharth and Sorensen (2005) related to outer rubble mound breakwaters but focus on optimum safety levels for outer caisson breakwaters on low and high rubble foundations placed on sea beds strong enough...... to resist geotechnical slip failures. Optimum safety levels formulated for use both in deterministic and probabilistic design procedures are given. Results obtained so far indicate that the optimum safety levels for caisson breakwaters are much higher than for rubble mound breakwaters....

OPTIMUM PROSESSENTRERING

Directory of Open Access Journals (Sweden)

K. Adendorff

2012-01-01

Full Text Available

ENGLISH ABSTRACT: The paper derives an expression for optimum process centreing for a given design specification and spoilage and/or rework costs.

AFRIKAANSE OPSOMMING: Die problem Van prosessentrering vir n gegewe ontwerpspesifikasie en herwerk- en/of skrootkoste word behandel.

The optimum support design selection by using AHP method for the main haulage road in WLC Tuncbilek colliery

Energy Technology Data Exchange (ETDEWEB)

Yavuz, M.; Iphar, M.; Once, G.

2008-03-15

The engineers can frequently encounter with the situation to select the optimum option among the alternatives related with mining operations. The optimum choice can be selected by the experienced engineers taking into consideration their judgement and intuition. However, decision-making methods can offer to the engineers to support their optimum selection for a particular application in the scientific way. The Analytical Hierarchy Process (AHP) is one of the multi attribute decision-making (MADM) methods utilizing structured pair-wise comparisons. This paper presents an application of the AHP method to the selection of the optimum support design for the main transport road, which has been planned for deep coal seam panels of Western Lignite Corporation (WLC) Tuncbilek in Turkeiy. The methodology considers eight main objectives, namely: four different displacement values for determined history locations, factor of safety (FOS), cost, labour and applicability factor for the selection of support design. The displacements and stress values were obtained by using the finite difference program FLAC(3D) as the numerical studies have been widely used by the engineers examining the response of any opening in underground, in advance. After carrying out several numerical models for different support design, the AHP method was incorporated to evaluate these support designs according to the pre-determined criteria. The result of this study shows that such AHP application can assist the engineers to effectively evaluate the support system alternatives for an underground mine.

Optimum Safety Levels for Breakwaters

DEFF Research Database (Denmark)

Burcharth, H. F.; Sørensen, John Dalsgaard

2005-01-01

Optimum design safety levels for rock and cube armoured rubble mound breakwaters without superstructure are investigated by numerical simulations on the basis of minimization of the total costs over the service life of the structure, taking into account typical uncertainties related to wave...... statistics and structure response. The study comprises the influence of interest rate, service lifetime, downtime costs and damage accumulation. Design limit states and safety classes for breakwaters are discussed. The results indicate that optimum safety levels are somewhat higher than the safety levels...

The computer-aided design of rubber-metal products

Directory of Open Access Journals (Sweden)

Pavlo S. Shvets

2015-12-01

Full Text Available The important problem in design of rubber-metal products is the optimization of their mass without sacrificing of proportionality factor is in the limits of standard. Aim: The aim of this work is to improve the computer-aided systems by development and implementation of improved optimization method in rubber-metal CAD systems for designers based on the reverse optimization. Materials and Methods: The paper studies the matters of computer-aided structural design of technical composite products composed of anisotropic materials that are essentially different in properties. Results: The structure of CAD systems for designers solving the problems of such design is offered and the work principles of its subsystems are described. It is shown that complicated systems optimization in CAD systems must consider as restrictions the entitative connection between separate elements of these systems within the area of the optimizing arguments. Conclusions: The problem of the “reverse” optimization when objective functions are the connectivity area parameters is considered. In many cases, this allows receiving solutions that are more effective during the computer-aided design process. The developed CAD system for designers was used during the production of rubber-metal shock absorbers at the Odessa Rubber Technical Articles Plant. The positive technical and economic effect was obtained.

Computer-aided system design

Science.gov (United States)

Walker, Carrie K.

1991-01-01

A technique has been developed for combining features of a systems architecture design and assessment tool and a software development tool. This technique reduces simulation development time and expands simulation detail. The Architecture Design and Assessment System (ADAS), developed at the Research Triangle Institute, is a set of computer-assisted engineering tools for the design and analysis of computer systems. The ADAS system is based on directed graph concepts and supports the synthesis and analysis of software algorithms mapped to candidate hardware implementations. Greater simulation detail is provided by the ADAS functional simulator. With the functional simulator, programs written in either Ada or C can be used to provide a detailed description of graph nodes. A Computer-Aided Software Engineering tool developed at the Charles Stark Draper Laboratory (CSDL CASE) automatically generates Ada or C code from engineering block diagram specifications designed with an interactive graphical interface. A technique to use the tools together has been developed, which further automates the design process.

Multiobjective Optimum Design of a 3-RRR Spherical Parallel Manipulator with Kinematic and Dynamic Dexterities

DEFF Research Database (Denmark)

Wu, Guanglei

2012-01-01

parameters of the spherical parallel manipulator. The proposed approach is illustrated with the optimum design of a special spherical parallel manipulator with unlimited rolling motion. The corresponding optimization problem aims to maximize the kinematic and dynamic dexterities over its regular shaped...

Further Developments on Optimum Structural Design Using MSC/Nastran and Sequential Quadratic Programming

DEFF Research Database (Denmark)

Holzleitner, Ludwig

1996-01-01

, here the shape of two dimensional parts with different thickness areas will be optimized. As in the previos paper, a methodology for structural optimization using the commercial finite element package MSC/NASTRAN for structural analysis is described. Three different methods for design sensitivity......This work is closely connected to the paper: K.G. MAHMOUD, H.W. ENGL and HOLZLEITNER: "OPTIMUM STRUCTURAL DESIGN USING MSC/NASTRAN AND SEQUENTIAL QUADRATIC PROGRAMMING", Computers & Structures, Vol. 52, No. 3, pp. 437-447, (1994). In contrast to that paper, where thickness optimization is described...

Calculations enable optimum design of magnetic brake

Science.gov (United States)

Kosmahl, H. G.

1966-01-01

Mathematical analysis and computations determine optimum magnetic coil configurations for a magnetic brake which controllably decelerates a free falling load to a soft stop. Calculations on unconventionally wound coils determine the required parameters for the desired deceleration with minimum electrical energy supplied to the stationary coil.

Optimum Design of a Moving Coil Actuator for Fast-Switching Valves in Digital Hydraulic Pumps and Motors

DEFF Research Database (Denmark)

Roemer, Daniel Beck; Bech, Michael Møller; Johansen, Per

2015-01-01

Fast-switching seat valves suitable for digital hydraulic pumps and motors utilize direct electromagnetic actuators, which must exhibit superior transient performance to allow efficient operation of the fluid power pump/motor. A moving coil actuator resulting in a minimum valve switching time...... is designed for such valves using transient finite-element analysis of the electromagnetic circuit. The valve dynamics are coupled to the fluid restrictive forces, which significantly influence the effective actuator force. Fluid forces are modeled based on transient computational fluid dynamics models....... The electromagnetic finite-element model is verified against experimental measurement, and used to design an optimum moving coil actuator for the application considering different voltage-current ratios of the power supply. Results show that the optimum design depends on the supply voltage-current ratio, however...

Fractography of clinically fractured, implant-supported dental computer-aided design and computer-aided manufacturing crowns

NARCIS (Netherlands)

Lohbauer, Ulrich; Belli, Renan; Cune, Marco S; Schepke, Ulf

2017-01-01

Today, a substantial part of the dental crown production uses computer-aided design and computer-aided manufacturing (CAD/CAM) technology. A recent step in restorative dentistry is the replacement of natural tooth structure with pre-polymerized and machined resin-based methacrylic polymers.

Integrated computer-aided design using minicomputers

Science.gov (United States)

Storaasli, O. O.

1980-01-01

Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM), a highly interactive software, has been implemented on minicomputers at the NASA Langley Research Center. CAD/CAM software integrates many formerly fragmented programs and procedures into one cohesive system; it also includes finite element modeling and analysis, and has been interfaced via a computer network to a relational data base management system and offline plotting devices on mainframe computers. The CAD/CAM software system requires interactive graphics terminals operating at a minimum of 4800 bits/sec transfer rate to a computer. The system is portable and introduces 'interactive graphics', which permits the creation and modification of models interactively. The CAD/CAM system has already produced designs for a large area space platform, a national transonic facility fan blade, and a laminar flow control wind tunnel model. Besides the design/drafting element analysis capability, CAD/CAM provides options to produce an automatic program tooling code to drive a numerically controlled (N/C) machine. Reductions in time for design, engineering, drawing, finite element modeling, and N/C machining will benefit productivity through reduced costs, fewer errors, and a wider range of configuration.

Computer aided product design

DEFF Research Database (Denmark)

Constantinou, Leonidas; Bagherpour, Khosrow; Gani, Rafiqul

1996-01-01

A general methodology for Computer Aided Product Design (CAPD) with specified property constraints which is capable of solving a large range of problems is presented. The methodology employs the group contribution approach, generates acyclic, cyclic and aromatic compounds of various degrees......-liquid equilibria (LLE), solid-liquid equilibria (SLE) and gas solubility. Finally, a computer program based on the extended methodology has been developed and the results from five case studies highlighting various features of the methodology are presented....

Optimum Design of Gravity Retaining Walls Using Charged System Search Algorithm

Directory of Open Access Journals (Sweden)

S. Talatahari

2012-01-01

Full Text Available This study focuses on the optimum design retaining walls, as one of the familiar types of the retaining walls which may be constructed of stone masonry, unreinforced concrete, or reinforced concrete. The material cost is one of the major factors in the construction of gravity retaining walls therefore, minimizing the weight or volume of these systems can reduce the cost. To obtain an optimal seismic design of such structures, this paper proposes a method based on a novel meta-heuristic algorithm. The algorithm is inspired by the Coulomb's and Gauss’s laws of electrostatics in physics, and it is called charged system search (CSS. In order to evaluate the efficiency of this algorithm, an example is utilized. Comparing the results of the retaining wall designs obtained by the other methods illustrates a good performance of the CSS. In this paper, we used the Mononobe-Okabe method which is one of the pseudostatic approaches to determine the dynamic earth pressure.

Optimum stacking sequence design of laminated composite circular plates with curvilinear fibres by a layer-wise optimization method

Science.gov (United States)

Guenanou, A.; Houmat, A.

2018-05-01

The optimum stacking sequence design for the maximum fundamental frequency of symmetrically laminated composite circular plates with curvilinear fibres is investigated for the first time using a layer-wise optimization method. The design variables are two fibre orientation angles per layer. The fibre paths are constructed using the method of shifted paths. The first-order shear deformation plate theory and a curved square p-element are used to calculate the objective function. The blending function method is used to model accurately the geometry of the circular plate. The equations of motion are derived using Lagrange's method. The numerical results are validated by means of a convergence test and comparison with published values for symmetrically laminated composite circular plates with rectilinear fibres. The material parameters, boundary conditions, number of layers and thickness are shown to influence the optimum solutions to different extents. The results should serve as a benchmark for optimum stacking sequences of symmetrically laminated composite circular plates with curvilinear fibres.

User involvement in the design and evaluation of a smart mobility aid.

Science.gov (United States)

Lacey, G; MacNamara, S

2000-01-01

This paper describes the design and evaluation of an innovative smart mobility aid for the frail visually impaired. The Personal Adaptive Mobility AID (PAM-AID) was developed to address the difficulties in personal mobility of the frail and elderly visually impaired. The paper provides an overview of the PAM-AID research at Trinity College and describes the evolutionary nature of the design process. Because there were no existing systems to guide its development, a series of prototypes was constructed and they were regularly evaluated in the field. This approach views potential users as vital contributing members of the design team and led to rapid and hopefully useful improvements in the design.

Three-dimensional computer aided design system for plant layout

International Nuclear Information System (INIS)

Yoshinaga, Toshiaki; Kiguchi, Takashi; Tokumasu, Shinji; Kumamoto, Kenjiro.

1986-01-01

The CAD system for three-dimensional plant layout planning, with which the layout of pipings, cable trays, air conditioning ducts and so on in nuclear power plants can be planned and designed effectively in a short period is reported. This system comprises the automatic routing system by storing the rich experience and know-how of designers in a computer as the knowledge, and deciding the layout automatically following the predetermined sequence by using these, the interactive layout system for reviewing the routing results from higher level and modifying to the optimum layout, the layout evaluation system for synthetically evaluating the layout from the viewpoint of the operability such as checkup and maintenance, and the data base system which enables these effective planning and design. In this report, the total constitution of this system and the technical features and effects of the individual subsystems are outlined. In this CAD system for three-dimensional plant layout planning, knowledge engineering, CAD/CAM, computer graphics and other latest technology were introduced, accordingly by applying this system to plant design, the design can be performed quickly, various case studies can be carried out at planning stage, and systematic and optimum layout planning becomes possible. (Kako, I.)

Optimum Design for Multi-angle Kitchen Grater Mechanism for Biodegrading Kitchen Waste

Directory of Open Access Journals (Sweden)

Razali Zol Bahri

2016-01-01

Full Text Available The study presented in this report is regarding on the conceptual design of the grater machine which meant to shred food wastes into small and fine size particle. This study will focus on the waste management factor of the food waste produced in the home kitchen. A study is conducted to compare the most suitable material and geometric shape of the grating blades by comparing with similar existing devices in the market. The chosen material and blade design are to be evaluated for its characteristics and performance by using the FEM method. The analysis is taking all the constraints regarding the design as well as its advantages are to be considered in designing a new grating blade for the optimum end product making. This design derived through in the consideration for the home application rather than domestic use. This brings the meaning that the compact and small size design. With the detailed evaluation of the stress reaction on the blades to provide the safety and sustainability factor of the device as well as the people that is using the device.

Optimum study designs.

Science.gov (United States)

Gu, C; Rao, D C

2001-01-01

Because simplistic designs will lead to prohibitively large sample sizes, the optimization of genetic study designs is critical for successfully mapping genes for complex diseases. Creative designs are necessary for detecting and amplifying the usually weak signals for complex traits. Two important outcomes of a study design--power and resolution--are implicitly tied together by the principle of uncertainty. Overemphasis on either one may lead to suboptimal designs. To achieve optimality for a particular study, therefore, practical measures such as cost-effectiveness must be used to strike a balance between power and resolution. In this light, the myriad of factors involved in study design can be checked for their effects on the ultimate outcomes, and the popular existing designs can be sorted into building blocks that may be useful for particular situations. It is hoped that imaginative construction of novel designs using such building blocks will lead to enhanced efficiency in finding genes for complex human traits.

Critiquing the Computer-Aided Design of Dental Prostheses.

Science.gov (United States)

Fitzpatrick, F. J.; And Others

This paper describes RaPiD, a computer-aided assistant for the design of dental prostheses called removable partial dentures. The user manipulates icons directly to indicate the desired design solution to a given clinical situation. A developing design is represented as a logic database of components in a design; expert rules are applied as…

Flow channel shape optimum design for hydroformed metal bipolar plate in PEM fuel cell

Energy Technology Data Exchange (ETDEWEB)

Peng, Linfa; Lai, Xinmin; Liu, Dong' an; Hu, Peng [State Key Laboratory of Mechanical System and Vibration, Shanghai Jiao Tong University, Shanghai 200240 (China); Ni, Jun [Department of Mechanical Engineering and Applied Mechanics, University of Michigan, Ann Arbor, MI 48109 (United States)

2008-03-15

Bipolar plate is one of the most important and costliest components of polymer electrolyte membrane (PEM) fuel cells. Micro-hydroforming is a promising process to reduce the manufacturing cost of PEM fuel cell bipolar plates made of metal sheets. As for hydroformed bipolar plates, the main defect is the rupture because of the thinning of metal sheet during the forming process. The flow channel section decides whether high quality hydroformed bipolar plates can be successively achieved or not. Meanwhile, it is also the key factor that is related with the reaction efficiency of the fuel cell stacks. In order to obtain the optimum flow channel section design prior the experimental campaign, some key geometric dimensions (channel depth, channel width, rib width and transition radius) of flow channel section, which are related with both reaction efficiency and formability, are extracted and parameterized as the design variables. By design of experiments (DOE) methods and an adoptive simulated annealing (ASA) optimization method, an optimization model of flow channel section design for hydroformed metal bipolar plate is proposed. Optimization results show that the optimum dimension values for channel depth, channel width, rib width and transition radius are 0.5, 1.0, 1. 6 and 0.5 mm, respectively with the highest reaction efficiency (79%) and the acceptable formability (1.0). Consequently, their use would lead to improved fuel cell efficiency for low cost hydroformed metal bipolar plates. (author)

Optimum systems design with random input and output applied to solar water heating

Science.gov (United States)

Abdel-Malek, L. L.

1980-03-01

Solar water heating systems are evaluated. Models were developed to estimate the percentage of energy supplied from the Sun to a household. Since solar water heating systems have random input and output queueing theory, birth and death processes were the major tools in developing the models of evaluation. Microeconomics methods help in determining the optimum size of the solar water heating system design parameters, i.e., the water tank volume and the collector area.

Computer aided architectural design : futures 2001

NARCIS (Netherlands)

Vries, de B.; Leeuwen, van J.P.; Achten, H.H.

2001-01-01

CAAD Futures is a bi-annual conference that aims to promote the advancement of computer-aided architectural design in the service of those concerned with the quality of the built environment. The conferences are organized under the auspices of the CAAD Futures Foundation, which has its secretariat

Performance characteristics of aerodynamically optimum turbines for wind energy generators

Science.gov (United States)

Rohrbach, C.; Worobel, R.

1975-01-01

This paper presents a brief discussion of the aerodynamic methodology for wind energy generator turbines, an approach to the design of aerodynamically optimum wind turbines covering a broad range of design parameters, some insight on the effect on performance of nonoptimum blade shapes which may represent lower fabrication costs, the annual wind turbine energy for a family of optimum wind turbines, and areas of needed research. On the basis of the investigation, it is concluded that optimum wind turbines show high performance over a wide range of design velocity ratios; that structural requirements impose constraints on blade geometry; that variable pitch wind turbines provide excellent power regulation and that annual energy output is insensitive to design rpm and solidity of optimum wind turbines.

Application of the successive linear programming technique to the optimum design of a high flux reactor using LEU fuel

International Nuclear Information System (INIS)

Mo, S.C.

1991-01-01

The successive linear programming technique is applied to obtain the optimum thermal flux in the reflector region of a high flux reactor using LEU fuel. The design variables are the reactor power, core radius and coolant channel thickness. The constraints are the cycle length, average heat flux and peak/average power density ratio. The characteristics of the optimum solutions with various constraints are discussed

[Clinical skills and outcomes of chair-side computer aided design and computer aided manufacture system].

Science.gov (United States)

Yu, Q

2018-04-09

Computer aided design and computer aided manufacture (CAD/CAM) technology is a kind of oral digital system which is applied to clinical diagnosis and treatment. It overturns the traditional pattern, and provides a solution to restore defect tooth quickly and efficiently. In this paper we mainly discuss the clinical skills of chair-side CAD/CAM system, including tooth preparation, digital impression, the three-dimensional design of prosthesis, numerical control machining, clinical bonding and so on, and review the outcomes of several common kinds of materials at the same time.

Navigation and Alignment Aids Concept of Operations and Supplemental Design Information. Revision A

Science.gov (United States)

Kelly, Sean M.; Cryan, Scott P.

2016-01-01

The IDSS Navigation and Alignment Aids Concept of Operations and Supplemental Design Information document provides supplemental information to the IDSS IDD. The guide provides insight into the navigation and alignment aids design, and how those aids can be utilized by incoming vehicles for proximity operations and docking. The navigation aids are paramount to successful docking.

Computer aided drug design

Science.gov (United States)

Jain, A.

2017-08-01

Computer based method can help in discovery of leads and can potentially eliminate chemical synthesis and screening of many irrelevant compounds, and in this way, it save time as well as cost. Molecular modeling systems are powerful tools for building, visualizing, analyzing and storing models of complex molecular structure that can help to interpretate structure activity relationship. The use of various techniques of molecular mechanics and dynamics and software in Computer aided drug design along with statistics analysis is powerful tool for the medicinal chemistry to synthesis therapeutic and effective drugs with minimum side effect.

Computer-aided Framework for Design of Pure, Mixed and Blended Products

DEFF Research Database (Denmark)

Cignitti, Stefano; Zhang, Lei; Gani, Rafiqul

2015-01-01

This paper presents a framework for computer-aided design of pure, mixed and blended chemical based products. The framework is a systematic approach to convert a Computer-aided Molecular, Mixture and Blend Design (CAMbD) formulation, based on needs and target properties, into a mixed integer non...

Applied orthogonal experiment design for the optimum microwave ...

African Journals Online (AJOL)

An experiment on polysaccharides from Rhodiolae Radix (PRR) extraction was carried out using microwave-assisted extraction (MAE) method with an objective to establishing the optimum MAE conditions of PRR. Single factor experiments were performed to determine the appropriate range of extraction conditions, and the ...

Optimum design of pultrusion process via evolutionary multi-objective optimization

DEFF Research Database (Denmark)

Tutum, Cem Celal; Baran, Ismet; Deb, Kalyanmoy

2014-01-01

Pultrusion is one of the most cost-effective manufacturing techniques for producing fiber-reinforced composites with constant cross-sectional profiles. This obviously makes it more attractive for both researchers and practitioners to investigate the optimum process parameters, i.e., pulling speed......, power, and dimensions of the heating platens, length and width of the heating die, design of the resin injection chamber, etc., to provide better understanding of the process, consequently to improve the efficiency of the process as well as the product quality. Using validated computer simulations...... this type of problems without any biased treatment of objectives such as weighting constants serving as pre-assumed user preferences. In this paper, first, a thermochemical simulation of the pultrusion process has been presented considering the steady-state conditions. Following that, it is integrated...

A layout designer's data projection reticle. [for optimum indicator instrument location in aircraft

Science.gov (United States)

Haines, R. F.

1977-01-01

The designer's projection reticle is a modified surplus weapons sighting device consisting of a 3.5 cm diameter, 8.9 focal length coated objective lens. It is placed 1.5 cm in front of a clear flat glass plate on which the aluminized reflective pattern has been deposited. Reflected light passes through the objective lens, off the front surface of the coating, and off the rear coated surface of the objective lens. Several reticle patterns have been designed and tested, and other patterns are in the planning stage. The device may be used for a variety of applications including determining the optimum locations on a cockpit panel for luminous warning indicators requiring rapid manual responses.

Optimum design and thermodynamic analysis of a gas turbine and ORC combined cycle with recuperators

International Nuclear Information System (INIS)

Cao, Yue; Gao, Yike; Zheng, Ya; Dai, Yiping

2016-01-01

Highlights: • A GT-ORC combined cycle with recuperators was designed. • The effect of the ORC turbine inlet pressure on the combined cycle was examined. • Toluene was a more suitable working fluid for the GT-ORC combined cycle. • The GT-ORC combined cycle performed better than the GT-Rankine combined cycle. • The sensitivity analysis to the ambient temperature was completed. - Abstract: Gas turbines are widely used in distributed power generation because of their high efficiency, low pollution and low operational cost. To further utilize the waste heat from gas turbines, an organic Rankine cycle (ORC) was proposed as the bottoming cycle for gas turbines in this paper. Two recuperators were coupled with the combined cycle to increase the thermal efficiency, and aromatics were chosen as the working fluid for the bottoming cycle. This paper focused on the optimum design and thermodynamic analysis of the gas turbine and ORC (GT-ORC) combined cycle. Results showed that the net power and thermal efficiency of the ORC increased with the ORC turbine inlet pressure and achieved optimum values at a specific pressure based on the optimum criteria. Furthermore, compared with the GT-Rankine combined cycle, the GT-ORC combined cycle had better thermodynamic performance. Toluene was a more suitable working fluid for the GT-ORC combined cycle. Moreover, ambient temperature sensitivity simulations concluded that the GT-ORC combined cycle had a maximum thermal efficiency and the combined cycle net power was mainly determined by the topping gas turbine cycle.

Development of reactor design aid tool using virtual reality technology

International Nuclear Information System (INIS)

Mizuguchi, N.; Tamura, Y.; Imagawa, S.; Sagara, A.; Hayashi, T.

2006-01-01

A new type of aid system for fusion reactor design, to which the virtual reality (VR) visualization and sonification techniques are applied, is developed. This system provides us with an intuitive interaction environment in the VR space between the observer and the designed objects constructed by the conventional 3D computer-aided design (CAD) system. We have applied the design aid tool to the heliotron-type fusion reactor design activity FFHR2m [A. Sagara, S. Imagawa, O. Mitarai, T. Dolan, T. Tanaka, Y. Kubota, et al., Improved structure and long -life blanket concepts for heliotron reactors, Nucl. Fusion 45 (2005) 258-263] on the virtual reality system CompleXcope [Y. Tamura, A. Kageyama, T. Sato, S. Fujiwara, H. Nakamura, Virtual reality system to visualize and auralize numerical imulation data, Comp. Phys. Comm. 142 (2001) 227-230] of the National Institute for Fusion Science, Japan, and have evaluated its performance. The tool includes the functions of transfer of the observer, translation and scaling of the objects, recording of the operations and the check of interference

Optimum Design of a Five-Phase Permanent Magnet Synchronous Motor for Underwater Vehicles by use of Particle Swarm Optimization

Directory of Open Access Journals (Sweden)

S. Asghar Gholamian

2012-12-01

Full Text Available Permanent magnet synchronous motors are efficient motors which have widespread applications in electric industry due to their noticeable features. One of the interesting applications of such motors is in underwater vehicles. In these cases, reaching to minimum volume and high torque of the motor are the major concern. Design optimization can enhance their merits considerably, thus reduce volume and improve performance of motors. In this paper, a new method for optimum design of a five-phase surface-mounted permanent magnet synchronous motor is presented to achieve minimum loss and magnet volume with an increased torque. A multi-objective optimization is performed in search for optimum dimensions of the motor and its permanent magnets using particle swarm optimization. The design optimization results in a motor with great improvement regarding the original motor. Finally, finite element analysis is utilized to validate the accuracy of the design.

Computer-Aided Design in Further Education.

Science.gov (United States)

Ingham, Peter, Ed.

This publication updates the 1982 occasional paper that was intended to foster staff awareness and assist colleges in Great Britain considering the use of computer-aided design (CAD) material in engineering courses. The paper begins by defining CAD and its place in the Integrated Business System with a brief discussion of the effect of CAD on the…

Thermal performance analysis and optimum design parameters of heat exchanger having perforated pin fins

International Nuclear Information System (INIS)

Sahin, Bayram; Demir, Alparslan

2008-01-01

This paper reports the heat transfer enhancement and corresponding pressure drop over a flat surface equipped with circular cross section perforated pin fins in a rectangular channel. The channel had a cross section area of 100-250 mm 2 . The experiments covered the following ranges: Reynolds number 13500-42,000, clearance ratio (C/H) 0, 0.33 and 1 and interfin spacing ratio (S y /D) 1.208, 1.524, 1.944 and 3.417. Correlation equations were developed for the heat transfer, friction factor and enhancement efficiency. The experimental results showed that the use of circular cross section pin fins may lead to heat transfer enhancement. Enhancement efficiencies varied between 1.4 and 2.6 depending on clearance ratio and interfin spacing ratio. Using a Taguchi experimental design method, optimum design parameters and their levels were investigated. Nusselt number and friction factor were considered as performance parameters. An L 9 (3 3 ) orthogonal array was selected as an experimental plan. First of all, each goal was optimized separately. Then, all the goals were optimized together, considering the priority of the goals, and the optimum results were found to be Reynolds number of 42,000, fin height of 50 mm and streamwise distance between fins of 51 mm

Computer-Aided Test Flow in Core-Based Design

NARCIS (Netherlands)

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of

State of the art in perceptual design of hearing aids

Science.gov (United States)

Edwards, Brent W.; van Tasell, Dianne J.

2002-05-01

Hearing aid capabilities have increased dramatically over the past six years, in large part due to the development of small, low-power digital signal processing chips suitable for hearing aid applications. As hearing aid signal processing capabilities increase, there will be new opportunities to apply perceptually based knowledge to technological development. Most hearing loss compensation techniques in today's hearing aids are based on simple estimates of audibility and loudness. As our understanding of the psychoacoustical and physiological characteristics of sensorineural hearing loss improves, the result should be improved design of hearing aids and fitting methods. The state of the art in hearing aids will be reviewed, including form factors, user requirements, and technology that improves speech intelligibility, sound quality, and functionality. General areas of auditory perception that remain unaddressed by current hearing aid technology will be discussed.

Computer-Aided Design Method of Warp-Knitted Jacquard Spacer Fabrics

Directory of Open Access Journals (Sweden)

Li Xinxin

2016-06-01

Full Text Available Based on a further study on knitting and jacquard principles, this paper presents a mathematical design model to make computer-aided design of warp-knitted jacquard spacer fabrics more efficient. The mathematical model with matrix method employs three essential elements of chain notation, threading and Jacquard designing. With this model, the processing to design warp-knitted jacquard spacer fabrics with CAD software is also introduced. In this study, the sports shoes which have separated functional areas according to the feet structure and characteristics of movement are analysed. The results show the different patterns on Jacquard spacer fabrics that are seamlessly stitched with jacquard technics. The computer-aided design method of warp-knitted jacquard spacer fabrics is efficient and simple.

Mechatronical Aided Concept (MAC) in Intelligent Transport Vehicles Design

OpenAIRE

Pavel Pavlasek

2003-01-01

This article deals with the principles of synergy effect of mechatronical aided concept (MAC) to the design of intelligent transport vehicles products applying CA technologies and virtual reality design methods. Also includes presentation of intelligent railway vehicle development.

Chapter 6 – Computer-Aided Molecular Design and Property Prediction

DEFF Research Database (Denmark)

Gani, Rafiqul; Zhang, L.; Kalakul, Sawitree

2017-01-01

for the initial stages of the design/development process. Therefore, computer-aided molecular design and property prediction techniques are two topics that play important roles in chemical product design, analysis, and application. In this chapter, an overview of the concepts, methods, and tools related......Today's society needs many chemical-based products for its survival, nutrition, health, transportation, agriculture, and the functioning of processes. Chemical-based products have to be designed/developed in order to meet these needs, while at the same time, they must be innovative and sustainable...... to these two topics are given. In addition, a generic computer-aided framework for the design of molecules, mixtures, and blends is presented. The application of the framework is highlighted for molecular products through two case studies involving the design of refrigerants and surfactants....

Framework for computer-aided systems design

International Nuclear Information System (INIS)

Esselman, W.H.

1992-01-01

Advanced computer technology, analytical methods, graphics capabilities, and expert systems contribute to significant changes in the design process. Continued progress is expected. Achieving the ultimate benefits of these computer-based design tools depends on successful research and development on a number of key issues. A fundamental understanding of the design process is a prerequisite to developing these computer-based tools. In this paper a hierarchical systems design approach is described, and methods by which computers can assist the designer are examined. A framework is presented for developing computer-based design tools for power plant design. These tools include expert experience bases, tutorials, aids in decision making, and tools to develop the requirements, constraints, and interactions among subsystems and components. Early consideration of the functional tasks is encouraged. Methods of acquiring an expert's experience base is a fundamental research problem. Computer-based guidance should be provided in a manner that supports the creativity, heuristic approaches, decision making, and meticulousness of a good designer

Computer Aided Design System for Developing Musical Fountain Programs

Institute of Scientific and Technical Information of China (English)

刘丹; 张乃尧; 朱汉城

2003-01-01

A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the development process more efficient. The system first analyzed the music form and sentiment using many basic features of the music to select a basic fountain program. Then, this program is simulated with 3-D animation and modified manually to achieve the desired results. Finally, the program is transformed to a computer control program to control the musical fountain in time with the music. A prototype system for the musical fountain was also developed. It was tested with many styles of music and users were quite satisfied with its performance. By integrating various functions, the proposed computer aided design system for developing musical fountain programs greatly simplified the design of the musical fountain programs.

DEVELOPMENT OF COMPUTER AIDED DESIGN OF CHAIN COUPLING

Directory of Open Access Journals (Sweden)

Sergey Aleksandrovich Sergeev

2015-12-01

Full Text Available The present paper describes the development stages of computer-aided design of chain couplings. The first stage is the automation of traditional design techniques (intermediate automation. The second integrated automation with the development of automated equipment and production technology, including on the basis of flexible manufacturing systems (high level of automation.

Optimum material gradient composition for the functionally graded ...

African Journals Online (AJOL)

This study investigates the relation between the material gradient properties and the optimum sensing/actuation design of the functionally graded piezoelectric beams. Three-dimensional (3D) finite element analysis has been employed for the prediction of an optimum composition profile in these types of sensors and ...

SOFTWARE FOR COMPUTER-AIDED DESIGN OF CROSS-WEDGE ROLLING

OpenAIRE

A. A. Abramov; S. V. Medvedev

2013-01-01

The issues of computer technology creation of 3D-design and engineering analysis of metal forming processes using cross wedge rolling methods (CWR) are considered. The developed software for computer-aided design and simulation of cross-wedge rolling is described.

Mechatronical Aided Concept (MAC in Intelligent Transport Vehicles Design

Directory of Open Access Journals (Sweden)

Pavel Pavlasek

2003-01-01

Full Text Available This article deals with the principles of synergy effect of mechatronical aided concept (MAC to the design of intelligent transport vehicles products applying CA technologies and virtual reality design methods. Also includes presentation of intelligent railway vehicle development.

The Research of Computer Aided Farm Machinery Designing Method Based on Ergonomics

Science.gov (United States)

Gao, Xiyin; Li, Xinling; Song, Qiang; Zheng, Ying

Along with agricultural economy development, the farm machinery product type Increases gradually, the ergonomics question is also getting more and more prominent. The widespread application of computer aided machinery design makes it possible that farm machinery design is intuitive, flexible and convenient. At present, because the developed computer aided ergonomics software has not suitable human body database, which is needed in view of farm machinery design in China, the farm machinery design have deviation in ergonomics analysis. This article puts forward that using the open database interface procedure in CATIA to establish human body database which aims at the farm machinery design, and reading the human body data to ergonomics module of CATIA can product practical application virtual body, using human posture analysis and human activity analysis module to analysis the ergonomics in farm machinery, thus computer aided farm machinery designing method based on engineering can be realized.

MOBIC: Designing a Travel Aid for Blind and Elderly People

Science.gov (United States)

Petrie, Helen; Johnson, Valerie; Strothotte, Thomas; Raab, Andreas; Fritz, Steffi; Michel, Rainer

This paper presents the research for the development of a new travel aid to increase the independent mobility of blind and elderly travellers. This aid will build on the technologies of geographical information systems (GIS) and the Global Positioning System (GPS). The MOBIC Travel Aid (MOTA) consists of two interrelated components: the MOBIC Pre-journey System (MOPS) to assist users in planning journeys and the MOBIC Outdoor System (MOODS) to execute these plans by providing users with orientation and navigation assistance during journeys. The MOBIC travel aid is complementary to primary mobility aids such as the long cane or guide dog. Results of a study of user requirements are presented and their implications for the initial design of the system are discussed.

Interpolation Filter Design for Hearing-Aid Audio Class-D Output Stage Application

DEFF Research Database (Denmark)

Pracný, Peter; Bruun, Erik; Llimos Muntal, Pere

2012-01-01

This paper deals with a design of a digital interpolation filter for a 3rd order multi-bit ΣΔ modulator with over-sampling ratio OSR = 64. The interpolation filter and the ΣΔ modulator are part of the back-end of an audio signal processing system in a hearing-aid application. The aim in this paper...... is to compare this design to designs presented in other state-of-the-art works ranging from hi-fi audio to hearing-aids. By performing comparison, trends and tradeoffs in interpolation filter design are indentified and hearing-aid specifications are derived. The possibilities for hardware reduction...... in the interpolation filter are investigated. Proposed design simplifications presented here result in the least hardware demanding combination of oversampling ratio, number of stages and number of filter taps among a number of filters reported for audio applications....

Torsional strength of computer-aided design/computer-aided manufacturing-fabricated esthetic orthodontic brackets.

Science.gov (United States)

Alrejaye, Najla; Pober, Richard; Giordano Ii, Russell

2017-01-01

To fabricate orthodontic brackets from esthetic materials and determine their fracture resistance during archwire torsion. Computer-aided design/computer-aided manufacturing technology (Cerec inLab, Sirona) was used to mill brackets with a 0.018 × 0.025-inch slot. Materials used were Paradigm MZ100 and Lava Ultimate resin composite (3M ESPE), Mark II feldspathic porcelain (Vita Zahnfabrik), and In-Ceram YZ zirconia (Vita Zahnfabrik). Ten brackets of each material were subjected to torque by a 0.018 × 0.025-inch stainless steel archwire (G&H) using a specially designed apparatus. The average moments and degrees of torsion necessary to fracture the brackets were determined and compared with those of commercially available alumina brackets, Mystique MB (Dentsply GAC). The YZ brackets were statistically significantly stronger than any other tested material in their resistance to torsion (P brackets. Resistance of MZ100 and Lava Ultimate composite resin brackets to archwire torsion was comparable to commercially available alumina ceramic brackets.

Computer-Aided Drug Design in Epigenetics

Science.gov (United States)

Lu, Wenchao; Zhang, Rukang; Jiang, Hao; Zhang, Huimin; Luo, Cheng

2018-03-01

Epigenetic dysfunction has been widely implicated in several diseases especially cancers thus highlights the therapeutic potential for chemical interventions in this field. With rapid development of computational methodologies and high-performance computational resources, computer-aided drug design has emerged as a promising strategy to speed up epigenetic drug discovery. Herein, we make a brief overview of major computational methods reported in the literature including druggability prediction, virtual screening, homology modeling, scaffold hopping, pharmacophore modeling, molecular dynamics simulations, quantum chemistry calculation and 3D quantitative structure activity relationship that have been successfully applied in the design and discovery of epi-drugs and epi-probes. Finally, we discuss about major limitations of current virtual drug design strategies in epigenetics drug discovery and future directions in this field.

Computer-Aided Drug Design in Epigenetics

Science.gov (United States)

Lu, Wenchao; Zhang, Rukang; Jiang, Hao; Zhang, Huimin; Luo, Cheng

2018-01-01

Epigenetic dysfunction has been widely implicated in several diseases especially cancers thus highlights the therapeutic potential for chemical interventions in this field. With rapid development of computational methodologies and high-performance computational resources, computer-aided drug design has emerged as a promising strategy to speed up epigenetic drug discovery. Herein, we make a brief overview of major computational methods reported in the literature including druggability prediction, virtual screening, homology modeling, scaffold hopping, pharmacophore modeling, molecular dynamics simulations, quantum chemistry calculation, and 3D quantitative structure activity relationship that have been successfully applied in the design and discovery of epi-drugs and epi-probes. Finally, we discuss about major limitations of current virtual drug design strategies in epigenetics drug discovery and future directions in this field. PMID:29594101

Computer aided design of nickel-base superalloys

International Nuclear Information System (INIS)

Lawrence, P.J.

1988-01-01

This paper describes a computer aided design process for Ni-base superalloys developed and employed at ASEA Brown Boveri. The technique involves a series of modules each of which predicts a particular property of a hypothetical new composition. In the first stage of the development of this design techniques modules were produced to predict phase stability, using PHACOMP, and high temperature creep strength and hot corrosion resistance, using multiple linear regression equations derived from the data in the literature. Alloys designed using these technique are also discussed and, in particular, shortcomings of the design process are highlighted. This information was then used to produce a revamped design methodology involving extra modules, including prediction of an alloy's gamma-prime content. (orig.)

Design issues for optimum solar cell configuration

Science.gov (United States)

Kumar, Atul; Thakur, Ajay D.

2018-05-01

A computer based simulation of solar cell structure is performed to study the optimization of pn junction configuration for photovoltaic action. The fundamental aspects of photovoltaic action viz, absorption, separation collection, and their dependence on material properties and deatails of device structures is discussed. Using SCAPS 1D we have simulated the ideal pn junction and shown the effect of band offset and carrier densities on solar cell performance. The optimum configuration can be achieved by optimizing transport of carriers in pn junction under effect of field dependent recombination (tunneling) and density dependent recombination (SRH, Auger) mechanisms.

An Approach to Optimum Joint Beamforming Design in a MIMO-OFDM Multiuser System

Directory of Open Access Journals (Sweden)

Pascual-Iserte Antonio

2004-01-01

Full Text Available This paper describes a multiuser scenario with several terminals acceding simultaneously to the same frequency channel. The objective is to design an optimal multiuser system that may be used as a comparative framework when evaluating other suboptimal solutions and to contribute to the already published works on this topic. The present work assumes that a centralized manager knows perfectly all the channel responses between all the terminals. According to this, the transmitters and receivers, using antenna arrays and leading to the so-called multiple-input-multiple-output (MIMO channels, are designed in a joint beamforming approach, attempting to minimize the total transmit power subject to quality of service (QoS constraints. Since this optimization problem is not convex, the use of the simulated annealing (SA technique is proposed to find the optimum solution.

Computer-Aided Drug Design in Epigenetics

Directory of Open Access Journals (Sweden)

Wenchao Lu

2018-03-01

Full Text Available Epigenetic dysfunction has been widely implicated in several diseases especially cancers thus highlights the therapeutic potential for chemical interventions in this field. With rapid development of computational methodologies and high-performance computational resources, computer-aided drug design has emerged as a promising strategy to speed up epigenetic drug discovery. Herein, we make a brief overview of major computational methods reported in the literature including druggability prediction, virtual screening, homology modeling, scaffold hopping, pharmacophore modeling, molecular dynamics simulations, quantum chemistry calculation, and 3D quantitative structure activity relationship that have been successfully applied in the design and discovery of epi-drugs and epi-probes. Finally, we discuss about major limitations of current virtual drug design strategies in epigenetics drug discovery and future directions in this field.

Computer-Aided Design of Antimicrobial Peptides

DEFF Research Database (Denmark)

Fjell, Christopher D.; Hancock, Robert E.W.; Jenssen, Håvard

2010-01-01

in antimicrobial activity. Consequently, the majority of peptides put into clinical trials have failed at some point, underlining the importance of a thorough peptide optimization. An important tool in peptide design and optimization is quantitative structure-activity relationship (QSAR) analysis, correlating...... chemical parameters with biological activities of the peptide, using statistical methods. In this review we will discuss two different in silico strategies of computer-aided antibacterial peptide design, a linear correlation model build as an extension of traditional principal component analysis (PCA......) and a non-linear artificial neural network model. Studies on structurally diverse peptides, have concluded that the PCA derived model are able to guide the antibacterial peptide design in a meaningful way, however requiring rather a high homology between the peptides in the test-set and the in silico...

Simulation Programs for Ph.D. Study of Analysis, Modeling and Optimum Design of Solar Domestic Hot Water Systems

DEFF Research Database (Denmark)

Qin, Lin

1999-01-01

The design of solar domestic hot water system is a complex process, due to characteristics inherent in solar heating technology. Recently, computer simulation has become a widely used technique to improve the understanding of the thermal processes in such systems. This report presents the detaile...... programs or units that were developed in the Ph.D study of " Analysis, Modeling and Optimum Design of Solar Domestic Hot Water Systems"....

Thermal characteristic of insulation for optimum design of RI transport package

International Nuclear Information System (INIS)

Lee, J. C.; Bang, K. S.; Seo, K. S.

2002-01-01

A package to transport the high level radioactive materials in required to withstand the hypothetical accident conditions as well as normal transport conditions according to IAEA and domestic regulations. The regulations require that the package should maintain the shielding, thermal and structural integrities to release no radioactive material. Thermal characteristics of insulations were evaluated and optimum insulation thickness was deduced for RI transport package. The package has a maximum capacity of 600 Curies for Ir-192 sealed source. The insulation thickness was decided with 10 mm of polyurethane form to maintain the thermal safety under fire accident condition. Thermal analysis was carried out for RI transport package, and it was shown that the thermal integrity of the package was maintained. The results obtained this study will be applied to a basic data for design of RI transport cask

An esthetics rehabilitation with computer-aided design/ computer-aided manufacturing technology.

Science.gov (United States)

Mazaro, Josá Vitor Quinelli; de Mello, Caroline Cantieri; Zavanelli, Adriana Cristina; Santiago, Joel Ferreira; Amoroso, Andressa Paschoal; Pellizzer, Eduardo Piza

2014-07-01

This paper describes a case of a rehabilitation involving Computer Aided Design/Computer Aided Manufacturing (CAD-CAM) system in implant supported and dental supported prostheses using zirconia as framework. The CAD-CAM technology has developed considerably over last few years, becoming a reality in dental practice. Among the widely used systems are the systems based on zirconia which demonstrate important physical and mechanical properties of high strength, adequate fracture toughness, biocompatibility and esthetics, and are indicated for unitary prosthetic restorations and posterior and anterior framework. All the modeling was performed by using CAD-CAM system and prostheses were cemented using resin cement best suited for each situation. The rehabilitation of the maxillary arch using zirconia framework demonstrated satisfactory esthetic and functional results after a 12-month control and revealed no biological and technical complications. This article shows the important of use technology CAD/CAM in the manufacture of dental prosthesis and implant-supported.

[Three-dimensional computer aided design for individualized post-and-core restoration].

Science.gov (United States)

Gu, Xiao-yu; Wang, Ya-ping; Wang, Yong; Lü, Pei-jun

2009-10-01

To develop a method of three-dimensional computer aided design (CAD) of post-and-core restoration. Two plaster casts with extracted natural teeth were used in this study. The extracted teeth were prepared and scanned using tomography method to obtain three-dimensional digitalized models. According to the basic rules of post-and-core design, posts, cores and cavity surfaces of the teeth were designed using the tools for processing point clouds, curves and surfaces on the forward engineering software of Tanglong prosthodontic system. Then three-dimensional figures of the final restorations were corrected according to the configurations of anterior teeth, premolars and molars respectively. Computer aided design of 14 post-and-core restorations were finished, and good fitness between the restoration and the three-dimensional digital models were obtained. Appropriate retention forms and enough spaces for the full crown restorations can be obtained through this method. The CAD of three-dimensional figures of the post-and-core restorations can fulfill clinical requirements. Therefore they can be used in computer-aided manufacture (CAM) of post-and-core restorations.

Computer-Aided Test Flow in Core-Based Design

OpenAIRE

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the test-pattern generation and fault coverage determination in the core based design. The basic core-test strategy that one has to apply in the core-based design is stated in this work. A Computer-Aided Test (CAT) flow is proposed resulting in accurate fault coverage of embedded cores. The CAT now is applied to a few cores within the Philips Core Test Pilot IC project

Application of Artificial Bee Colony Algorithm and Finite Element Analysis for Optimum Design of Brushless Permanent Magnet Motor

Directory of Open Access Journals (Sweden)

Reza Ilka

2012-04-01

Full Text Available ABSTRACT: This paper develops a mathematical relationship for the purpose of designing and selecting the optimum dimensions of a brushless permanent magnet motor. The design is optimised by the use of artificial bee colony algorithm with the goal of maximizing the power density and efficiency of the motor. The required dimensions of the brushless motor are calculated based on the optimum power density and efficiency requirements. Finally, the predicted results of the optimisation are validated using a 2-D numerical program based on finite element analysis.ABSTRAK: Kajian ini mencadangkan persamaan yang menghubungkan rekabentuk dan dimensi magnet motor kekal tanpa berus. Rekabentuk optima berdasarkan algorisma koloni lebah tiruan dengan tujuan meningkatkan ketumpatan kuasa dan keberkesanan dibentangkan dalam kajian ini. Dimensi magnet motor kekal tanpa berus dihitung dengan ketumpatan kuasa optima dan keberkesanan. Akhirnya, keputusan telah disahkan dengan menggunakan program berangka 2-D berdasarkan analisis elemen finit.KEYWORDS: brushless; permanent magnet motor; power density; artificial bee colony; algorithm; finite element analysis

Computer-aided control system design

International Nuclear Information System (INIS)

Lebenhaft, J.R.

1986-01-01

Control systems are typically implemented using conventional PID controllers, which are then tuned manually during plant commissioning to compensate for interactions between feedback loops. As plants increase in size and complexity, such controllers can fail to provide adequate process regulations. Multivariable methods can be utilized to overcome these limitations. At the Chalk River Nuclear Laboratories, modern control systems are designed and analyzed with the aid of MVPACK, a system of computer programs that appears to the user like a high-level calculator. The software package solves complicated control problems, and provides useful insight into the dynamic response and stability of multivariable systems

Computer–Aided Design of the Critical Speed of Shafts | Akpobi ...

African Journals Online (AJOL)

A computer aided design software for the analysis of the critical speed of shaft, is developed and presented in this work. The software was designed using the principles of object oriented programming, and implemented with the Microsoft Visual Basic Language. The package was tested on a number of benchmark design ...

Optimum drying time for palm nuts for efficient nut cracking in small ...

African Journals Online (AJOL)

Palm kernel, one of the end products of oil palm fruit processing is recovered by the cracking of the palm nuts which is first dried to aid efficient kernel recovery. In small-scale mills palm nuts are air-dried. This paper investigates the optimum drying time necessary for efficient nut cracking. Such factors as wholeness of kernel, ...

Optimum source/drain overlap design for 16 nm high-k/metal gate MOSFETs

International Nuclear Information System (INIS)

Jang, Junyong; Lim, Towoo; Kim, Youngmin

2009-01-01

We explore a source/drain (S/D) design for a 16 nm MOSFET utilizing a replacement process for a high-k gate dielectric and metal gate electrode integration. Using TCAD simulation, a trade-off study between series resistance and overlap capacitance is carried out for a high-k dielectric surrounding gate structure, which results from the replacement process. An optimum S/D overlap to gate for the high-k surrounding gate structure is found to be different from the conventional gate structure, i.e. 0∼1 nm underlap is preferred for the surround high-k gate structure while 1∼2 nm overlap for the conventional gate one

Optimum design of Nd-doped fiber optical amplifiers

DEFF Research Database (Denmark)

Rasmussen, Thomas; Bjarklev, Anders Overgaard; Lumholt, Ole

1992-01-01

The waveguide parameters for a Nd-doped fluoride (Nd:ZBLANP) fiber amplifier have been optimized for small-signal and booster operation using an accurate numerical model. The optimum cutoff wavelength is shown to be 800 nm and the numerical aperture should be made as large as possible. Around 80%......% booster quantum conversion efficiency can be reached for an input power of 10 dBm and a pump power of 100 mW by the use of one filter...

A Multi-step and Multi-level approach for Computer Aided Molecular Design

DEFF Research Database (Denmark)

. The problem formulation step incorporates a knowledge base for the identification and setup of the design criteria. Candidate compounds are identified using a multi-level generate and test CAMD solution algorithm capable of designing molecules having a high level of molecular detail. A post solution step...... using an Integrated Computer Aided System (ICAS) for result analysis and verification is included in the methodology. Keywords: CAMD, separation processes, knowledge base, molecular design, solvent selection, substitution, group contribution, property prediction, ICAS Introduction The use of Computer...... Aided Molecular Design (CAMD) for the identification of compounds having specific physic...

Topology optimization aided structural design: Interpretation, computational aspects and 3D printing.

Science.gov (United States)

Kazakis, Georgios; Kanellopoulos, Ioannis; Sotiropoulos, Stefanos; Lagaros, Nikos D

2017-10-01

Construction industry has a major impact on the environment that we spend most of our life. Therefore, it is important that the outcome of architectural intuition performs well and complies with the design requirements. Architects usually describe as "optimal design" their choice among a rather limited set of design alternatives, dictated by their experience and intuition. However, modern design of structures requires accounting for a great number of criteria derived from multiple disciplines, often of conflicting nature. Such criteria derived from structural engineering, eco-design, bioclimatic and acoustic performance. The resulting vast number of alternatives enhances the need for computer-aided architecture in order to increase the possibility of arriving at a more preferable solution. Therefore, the incorporation of smart, automatic tools in the design process, able to further guide designer's intuition becomes even more indispensable. The principal aim of this study is to present possibilities to integrate automatic computational techniques related to topology optimization in the phase of intuition of civil structures as part of computer aided architectural design. In this direction, different aspects of a new computer aided architectural era related to the interpretation of the optimized designs, difficulties resulted from the increased computational effort and 3D printing capabilities are covered here in.

Computer aided molecular design with combined molecular modeling and group contribution

DEFF Research Database (Denmark)

Harper, Peter Mathias; Gani, Rafiqul; Kolar, Petr

1999-01-01

Computer-aided molecular design (CAMD) provides a means for determining molecules or mixtures of molecules (CAMMD) having a desirable set of physicochemical properties. The application range of CAMD is restricted due to limitations on the complexity of the generated molecular structures and on th......Computer-aided molecular design (CAMD) provides a means for determining molecules or mixtures of molecules (CAMMD) having a desirable set of physicochemical properties. The application range of CAMD is restricted due to limitations on the complexity of the generated molecular structures...

Technology computer aided design simulation for VLSI MOSFET

CERN Document Server

Sarkar, Chandan Kumar

2013-01-01

Responding to recent developments and a growing VLSI circuit manufacturing market, Technology Computer Aided Design: Simulation for VLSI MOSFET examines advanced MOSFET processes and devices through TCAD numerical simulations. The book provides a balanced summary of TCAD and MOSFET basic concepts, equations, physics, and new technologies related to TCAD and MOSFET. A firm grasp of these concepts allows for the design of better models, thus streamlining the design process, saving time and money. This book places emphasis on the importance of modeling and simulations of VLSI MOS transistors and

Modification of design methods to suit computer aided design of pumps

International Nuclear Information System (INIS)

Kumaraswamy, S.

1994-01-01

Engineering designs involve a large number of repetitive calculations to achieve optimisation. So, computers which are fast and accurate lend themselves as an aid for the design process. However, certain modifications in the steps of conventional design method become necessary for easier adaptation. In addition, it will be advantageous if the empirical coefficients of design are allowed to be chosen by the designer with prompting of ranges taken from design charts by the program itself. This paper describes two examples of modification in pump design. In the first case Anderson's area ratio method and Pfleiderer's Slip power methods are combined to achieve an integrated design of impeller and casing. The second case is the design of a Mixed flow pump impeller by considering it as an assembly of a number of radial flow pump impellers called part impellers. In addition, these modifications are useful in redesign for a different operating condition or in matching of impellers to existing casings. (author). 13 refs., 4 figs

Computer aided analysis, simulation and optimisation of thermal sterilisation processes.

Science.gov (United States)

Narayanan, C M; Banerjee, Arindam

2013-04-01

Although thermal sterilisation is a widely employed industrial process, little work is reported in the available literature including patents on the mathematical analysis and simulation of these processes. In the present work, software packages have been developed for computer aided optimum design of thermal sterilisation processes. Systems involving steam sparging, jacketed heating/cooling, helical coils submerged in agitated vessels and systems that employ external heat exchangers (double pipe, shell and tube and plate exchangers) have been considered. Both batch and continuous operations have been analysed and simulated. The dependence of del factor on system / operating parameters such as mass or volume of substrate to be sterilised per batch, speed of agitation, helix diameter, substrate to steam ratio, rate of substrate circulation through heat exchanger and that through holding tube have been analysed separately for each mode of sterilisation. Axial dispersion in the holding tube has also been adequately accounted for through an appropriately defined axial dispersion coefficient. The effect of exchanger characteristics/specifications on the system performance has also been analysed. The multiparameter computer aided design (CAD) software packages prepared are thus highly versatile in nature and they permit to make the most optimum choice of operating variables for the processes selected. The computed results have been compared with extensive data collected from a number of industries (distilleries, food processing and pharmaceutical industries) and pilot plants and satisfactory agreement has been observed between the two, thereby ascertaining the accuracy of the CAD softwares developed. No simplifying assumptions have been made during the analysis and the design of associated heating / cooling equipment has been performed utilising the most updated design correlations and computer softwares.

Equivalent circuit and optimum design of a multilayer laminated piezoelectric transformer.

Science.gov (United States)

Dong, Shuxiang; Carazo, Alfredo Vazquez; Park, Seung Ho

2011-12-01

A multilayer laminated piezoelectric Pb(Zr(1-x)Ti(x))O(3) (PZT) ceramic transformer, operating in a half- wavelength longitudinal resonant mode (λ/2 mode), has been analyzed. This piezoelectric transformer is composed of one thickness-polarized section (T-section) for exciting the longitudinal mechanical vibrations, two longitudinally polarized sections (L-section) for generating high-voltage output, and two insulating layers laminated between the T-section and L-section layers to provide insulation between the input and output sections. Based on the piezoelectric constitutive and motion equations, an electro-elasto-electric (EEE) equivalent circuit has been developed, and correspondingly, an effective EEE coupling coefficient was proposed for optimum design of this multilayer transformer. Commercial finite element analysis software is used to determine the validity of the developed equivalent circuit. Finally, a prototype sample was manufactured and experimental data was collected to verify the model's validity.

Application of numerical simulation on optimum design of two-dimensional sedimentation tanks in the wastewater treatment plant.

Science.gov (United States)

Zeng, Guang-Ming; Zhang, Shuo-Fu; Qin, Xiao-Sheng; Huang, Guo-He; Li, Jian-Bing

2003-05-01

The paper establishes the relationship between the settling efficiency and the sizes of the sedimentation tank through the process of numerical simulation, which is taken as one of the constraints to set up a simple optimum designing model of sedimentation tank. The feasibility and advantages of this model based on numerical calculation are verified through the application of practical case.

Designing an optimum pulsed magnetic field by a resistance/self-inductance/capacitance discharge system and alignment of carbon nanotubes embedded in polypyrrole matrix

Science.gov (United States)

Kazemikia, Kaveh; Bonabi, Fahimeh; Asadpoorchallo, Ali; Shokrzadeh, Majid

2015-02-01

In this work, an optimized pulsed magnetic field production apparatus is designed based on a RLC (Resistance/Self-inductance/Capacitance) discharge circuit. An algorithm for designing an optimum magnetic coil is presented. The coil is designed to work at room temperature. With a minor physical reinforcement, the magnetic flux density can be set up to 12 Tesla with 2 ms duration time. In our design process, the magnitude and the length of the magnetic pulse are the desired parameters. The magnetic field magnitude in the RLC circuit is maximized on the basis of the optimal design of the coil. The variables which are used in the optimization process are wire diameter and the number of coil layers. The coil design ensures the critically damped response of the RLC circuit. The electrical, mechanical, and thermal constraints are applied to the design process. A locus of probable magnetic flux density values versus wire diameter and coil layer is provided to locate the optimum coil parameters. Another locus of magnetic flux density values versus capacitance and initial voltage of the RLC circuit is extracted to locate the optimum circuit parameters. Finally, the application of high magnetic fields on carbon nanotube-PolyPyrrole (CNT-PPy) nano-composite is presented. Scanning probe microscopy technique is used to observe the orientation of CNTs after exposure to a magnetic field. The result shows alignment of CNTs in a 10.3 Tesla, 1.5 ms magnetic pulse.

Study on Optimum Design of Multi-Pole Interior Permanent Magnet Motor with Concentrated Windings

Science.gov (United States)

Kano, Yoshiaki; Kosaka, Takashi; Matsui, Nobuyuki

Interior Permanent Magnet Synchronous Motors (IPMSM) have been found in many applications because of their high-power density and high-efficiency. The existence of a complex magnetic circuit, however, makes the design of this machine quite complicated. Although FEM is commonly used in the IPMSM design, one of disadvantages is long CPU times. This paper presents a simple non-linear magnetic analysis for a multi-pole IPMSM as a preliminary design tool of FEM. The proposed analysis consists of the geometric-flux-tube-based equivalent-magnetic-circuit model. The model includes saturable permeances taking into account the local magnetic saturation in the core. As a result, the proposed analysis is capable of calculating the flux distribution and the torque characteristics in the presence of magnetic saturation. The effectiveness of the proposed analysis is verified by comparing with FEM in terms of the analytical accuracy and the computation time for two IPMSMs with different specifications. After verification, the proposed analysis-based optimum design is examined, by which the minimization of motor volume is realized while satisfying the necessary maximum torque for target applications.

Computer-aided design of new metal binders

International Nuclear Information System (INIS)

Varnek, A.; Fourches, D.; Klimchuk, O.; Marcou, G.; Kireeva, N.; Tsivadze, A.; Solov'ev, V.

2008-01-01

Chemoinformatics approaches open new opportunities for computer-aided design of new efficient metal binders. Here, we demonstrate performances of ISIDA and COMET software tools to predict stability constants (log K) of the metal ion/organic ligand complexes in solution and to design in silico new molecules possessing desirable properties. The predictive models for log K of lanthanides complexation in water have been developed. Some new uranyl binders based on monoamides and on phosphoryl-containing podands were suggested theoretically, then synthesized and tested experimentally. Reasonable agreement between experimental uranyl distribution coefficients and theoretically predicted values has been observed. (orig.)

Computer Aided Methodology for Simultaneous Synthesis, Design & Analysis of Chemical Products-Processes

DEFF Research Database (Denmark)

d'Anterroches, Loïc; Gani, Rafiqul

2006-01-01

A new combined methodology for computer aided molecular design and process flowsheet design is presented. The methodology is based on the group contribution approach for prediction of molecular properties and design of molecules. Using the same principles, process groups have been developed...... a wide range of problems. In this paper, only the computer aided flowsheet design related features are presented....... together with their corresponding flowsheet property models. To represent the process flowsheets in the same way as molecules, a unique but simple notation system has been developed. The methodology has been converted into a prototype software, which has been tested with several case studies covering...

Computer-aided Nonlinear Control System Design Using Describing Function Models

CERN Document Server

Nassirharand, Amir

2012-01-01

A systematic computer-aided approach provides a versatile setting for the control engineer to overcome the complications of controller design for highly nonlinear systems. Computer-aided Nonlinear Control System Design provides such an approach based on the use of describing functions. The text deals with a large class of nonlinear systems without restrictions on the system order, the number of inputs and/or outputs or the number, type or arrangement of nonlinear terms. The strongly software-oriented methods detailed facilitate fulfillment of tight performance requirements and help the designer to think in purely nonlinear terms, avoiding the expedient of linearization which can impose substantial and unrealistic model limitations and drive up the cost of the final product. Design procedures are presented in a step-by-step algorithmic format each step being a functional unit with outputs that drive the other steps. This procedure may be easily implemented on a digital computer with example problems from mecha...

Determination of the optimum design through different funding scenarios for future parabolic trough solar power plant in Algeria

International Nuclear Information System (INIS)

Trad, Ameur; Ait Ali, Mohand Ameziane

2015-01-01

Highlights: • Seven technical design options have been simulated. • The integration of auxiliary heating and TES stabilize electricity generation. • Impact of TES on the technical and economic performance of PTSPP projects. • Different funding scenarios to assess the profitability of CSP plant. • Sensitivity analysis plays an important role in building energy analysis. - Abstract: The purpose of this study is to determine an optimum design for a projected parabolic trough solar power plant (PTSPP) under Algerian climate through different funding scenarios. In this paper, seven different (d1–d7) designs for PTSPP have been developed for the Naâma site. Plant size, technology type, storage capacity, location of the plant, Operation and Maintenance (O and M) costs, replacement costs, fuel consumption, net CO 2 emission, levelized electricity cost, net power generation, specific investment costs and discount rate are the basis factors to determine the optimum sustainable design for PTSPP. The most attractive designs of each base technology were selected as D1, D2 and D3. The preferable design of three funding scenarios was finally selected on economic, financial and sensitivity analysis. It is finally concluded that, under the most favorable economic conditions allowed in this study, design D3 is the most advantageous in terms of benefit to cost ratio: its power output will be 100 MW el with 8 full load hours thermal energy storage. It was also found that for design D3 under funding scenario S2, the project will require an upfront grant of 396 MEUR. This corresponds to around 56% of the total investment cost and the payback period will be approximately 7 years

Energy-aware memory management for embedded multimedia systems a computer-aided design approach

CERN Document Server

Balasa, Florin

2011-01-01

Energy-Aware Memory Management for Embedded Multimedia Systems: A Computer-Aided Design Approach presents recent computer-aided design (CAD) ideas that address memory management tasks, particularly the optimization of energy consumption in the memory subsystem. It explains how to efficiently implement CAD solutions, including theoretical methods and novel algorithms. The book covers various energy-aware design techniques, including data-dependence analysis techniques, memory size estimation methods, extensions of mapping approaches, and memory banking approaches. It shows how these techniques

PUZZLE - A program for computer-aided design of printed circuit artwork

Science.gov (United States)

Harrell, D. A. W.; Zane, R.

1971-01-01

Program assists in solving spacing problems encountered in printed circuit /PC/ design. It is intended to have maximum use for two-sided PC boards carrying integrated circuits, and also aids design of discrete component circuits.

Optimum thermal design of microchannel heat sink with triangular reentrant cavities

International Nuclear Information System (INIS)

Xia Guodong; Chai Lei; Wang Haiyan; Zhou Mingzheng; Cui Zhenzhen

2011-01-01

The effect of geometric parameters on water flow and heat transfer characteristics in microchannel heat sink with triangular reentrant cavities is numerically investigated. A three-dimensional laminar flow model, consisting of Navier-Stokes equations and energy conservation equation, with the conjugate heat transfer between the silicon base and water taken into consideration is solved numerically. In order to find the optimum geometric parameters, four variables, representing the distance and geometry of the triangular reentrant cavity, are designed. It is found that the vortices in the triangular reentrant cavities lead to chaotic advection and can greatly enhance the convective fluid mixing. The thermal and hydraulic boundary layers are interrupted and the repeated developing flow enhances heat transfer in the constant cross-section segment. Furthermore, the effects of the four design variables on heat transfer augmentation and pressure drop penalty are investigated depending on different Reynolds numbers by using the simulated annealing method. Based on the thermal enhancement factor performance maps, the optimal geometric parameters are obtained in principle. - Research highlights: → The microchannels with different triangular reentrant cavities are numerically investigated. → The heat transfer enhancement attributes to fluid mixing and redeveloped thermal boundary layers. → The optimal distance and geometry of the triangular reentrant cavity are obtained in principle.

First-aid boxes - Reminder

CERN Multimedia

GS Department

2010-01-01

With a view to ensuring optimum use of the first-aid boxes on the CERN site, we should like to remind you of various changes introduced in March 2009: The TSO of the buildings concerned is responsible for the first-aid boxes, including checking their contents.   First-aid boxes may be restocked ONLY at the CERN stores (SCEM No. 54.99.80). This is no longer possible at the Infirmary. The associated cost is charged to the Departments.   First-aid boxes should be used only for mild injuries. All other cases should be referred to the Medical Service Infirmary (Bldg. 57 – ground-floor, tel. 73802) between 8.00 a.m. and 5.30 p.m. or to the Fire and Rescue Service (tel. 74444). N.B.: This information does not apply to the red emergency first-aid boxes in the underground areas or to the emergency kits for use in the event of being splashed with hydrofluoric acid.

Computer aided system for parametric design of combination die

Science.gov (United States)

Naranje, Vishal G.; Hussein, H. M. A.; Kumar, S.

2017-09-01

In this paper, a computer aided system for parametric design of combination dies is presented. The system is developed using knowledge based system technique of artificial intelligence. The system is capable to design combination dies for production of sheet metal parts having punching and cupping operations. The system is coded in Visual Basic and interfaced with AutoCAD software. The low cost of the proposed system will help die designers of small and medium scale sheet metal industries for design of combination dies for similar type of products. The proposed system is capable to reduce design time and efforts of die designers for design of combination dies.

Computer-Aided Test Flow in Core-Based Design

NARCIS (Netherlands)

Zivkovic, V.; Tangelder, R.J.W.T.; Kerkhoff, Hans G.

2000-01-01

This paper copes with the efficient test-pattern generation in a core-based design. A consistent Computer-Aided Test (CAT) flow is proposed based on the required core-test strategy. It generates a test-pattern set for the embedded cores with high fault coverage and low DfT area overhead. The CAT

Microwave processing of a dental ceramic used in computer-aided design/computer-aided manufacturing.

Science.gov (United States)

Pendola, Martin; Saha, Subrata

2015-01-01

Because of their favorable mechanical properties and natural esthetics, ceramics are widely used in restorative dentistry. The conventional ceramic sintering process required for their use is usually slow, however, and the equipment has an elevated energy consumption. Sintering processes that use microwaves have several advantages compared to regular sintering: shorter processing times, lower energy consumption, and the capacity for volumetric heating. The objective of this study was to test the mechanical properties of a dental ceramic used in computer-aided design/computer-aided manufacturing (CAD/CAM) after the specimens were processed with microwave hybrid sintering. Density, hardness, and bending strength were measured. When ceramic specimens were sintered with microwaves, the processing times were reduced and protocols were simplified. Hardness was improved almost 20% compared to regular sintering, and flexural strength measurements suggested that specimens were approximately 50% stronger than specimens sintered in a conventional system. Microwave hybrid sintering may preserve or improve the mechanical properties of dental ceramics designed for CAD/CAM processing systems, reducing processing and waiting times.

The Effects of Computer-Aided Design Software on Engineering Students' Spatial Visualisation Skills

Science.gov (United States)

Kösa, Temel; Karakus, Fatih

2018-01-01

The purpose of this study was to determine the influence of computer-aided design (CAD) software-based instruction on the spatial visualisation skills of freshman engineering students in a computer-aided engineering drawing course. A quasi-experimental design was applied, using the Purdue Spatial Visualization Test-Visualization of Rotations…

Computer aided design and development of mixed-propeller pumps

International Nuclear Information System (INIS)

Bhaoyal, B.C.

1994-01-01

This paper deals with the design principle of mixed propeller hydraulic aided by CADD software developed by author for generation of the hydraulic profile of the mixed propeller and diffuser geometry. The design methodology for plotting the vane profile of mixed propeller pump has been discussed in detail with special reference to conformal transformation in cylindrical as well as conical plane. (author). 10 refs., 11 figs

Development of Non-Optimum Factors for Launch Vehicle Propellant Tank Bulkhead Weight Estimation

Science.gov (United States)

Wu, K. Chauncey; Wallace, Matthew L.; Cerro, Jeffrey A.

2012-01-01

Non-optimum factors are used during aerospace conceptual and preliminary design to account for the increased weights of as-built structures due to future manufacturing and design details. Use of higher-fidelity non-optimum factors in these early stages of vehicle design can result in more accurate predictions of a concept s actual weights and performance. To help achieve this objective, non-optimum factors are calculated for the aluminum-alloy gores that compose the ogive and ellipsoidal bulkheads of the Space Shuttle Super-Lightweight Tank propellant tanks. Minimum values for actual gore skin thicknesses and weld land dimensions are extracted from selected production drawings, and are used to predict reference gore weights. These actual skin thicknesses are also compared to skin thicknesses predicted using classical structural mechanics and tank proof-test pressures. Both coarse and refined weights models are developed for the gores. The coarse model is based on the proof pressure-sized skin thicknesses, and the refined model uses the actual gore skin thicknesses and design detail dimensions. To determine the gore non-optimum factors, these reference weights are then compared to flight hardware weights reported in a mass properties database. When manufacturing tolerance weight estimates are taken into account, the gore non-optimum factors computed using the coarse weights model range from 1.28 to 2.76, with an average non-optimum factor of 1.90. Application of the refined weights model yields non-optimum factors between 1.00 and 1.50, with an average non-optimum factor of 1.14. To demonstrate their use, these calculated non-optimum factors are used to predict heavier, more realistic gore weights for a proposed heavy-lift launch vehicle s propellant tank bulkheads. These results indicate that relatively simple models can be developed to better estimate the actual weights of large structures for future launch vehicles.

Aiding Design of Wave Energy Converters via Computational Simulations

Science.gov (United States)

Jebeli Aqdam, Hejar; Ahmadi, Babak; Raessi, Mehdi; Tootkaboni, Mazdak

2015-11-01

With the increasing interest in renewable energy sources, wave energy converters will continue to gain attention as a viable alternative to current electricity production methods. It is therefore crucial to develop computational tools for the design and analysis of wave energy converters. A successful design requires balance between the design performance and cost. Here an analytical solution is used for the approximate analysis of interactions between a flap-type wave energy converter (WEC) and waves. The method is verified using other flow solvers and experimental test cases. Then the model is used in conjunction with a powerful heuristic optimization engine, Charged System Search (CSS) to explore the WEC design space. CSS is inspired by charged particles behavior. It searches the design space by considering candidate answers as charged particles and moving them based on the Coulomb's laws of electrostatics and Newton's laws of motion to find the global optimum. Finally the impacts of changes in different design parameters on the power takeout of the superior WEC designs are investigated. National Science Foundation, CBET-1236462.

Analysis, modeling and optimum design of solar domestic hot water systems

Energy Technology Data Exchange (ETDEWEB)

Lin Qin

1998-12-31

The object of this study was dynamic modeling, simulation and optimum design of solar DHW (domestic hot water) systems, with respect to different whether conditions, and accurate dynamic behaviour of the heat load. Special attention was paid to systems with thermosyphon and drain-back design. The solar radiation in Beijing (China) and in Denmark are analyzed both by theoretical calculations and the analysis of long-term measurements. Based on the weather data from the Beijing Meteorological Station during the period of 1981-1993, a Beijing Test Reference Year has been formulated by means of statistical analysis. A brief introduction about the Danish Test Reference Year and the Design Reference Year is also presented. In order to investigate the heat loss as a part of the total heat load, dynamic models for distribution networks have been developed, and simulations have been carried out for typically designed distribution networks of the circulation type. The influence of operation parameters such as the tank outlet temperature, the hot-water load and the load pattern, on the heat loss from the distribution networks in presented. It was found that the tank outlet temperature has a significant influence on the heat loss from a circulation type of distribution network, while the hot-water load and the load pattern have no obvious effect. Dynamic models of drain-back tanks, both as a separated tank and combined with a mantle tank, have been developed and presented. Models of the other basic components commonly used in solar DHW systems, such as flat-plate collectors, connection pipes, storage tanks with a heat exchanger spiral, and controllers, are also described. (LN) 66 refs.

Computer Aided Design of Kaplan Turbine Piston with SolidWorks

OpenAIRE

Camelia Jianu

2010-01-01

The paper presents the steps for 3D computer aided design (CAD) of Kaplan turbine piston made in SolidWorks.The present paper is a tutorial for a Kaplan turbine piston 3D geometry, which is dedicaded to the Parts Sketch and Parts Features design and Drawing Geometry and Drawing Annotation.

The Development of Computer-Aided Design for Electrical Equipment Selection and Arrangement of 10 Kv Switchgear

Directory of Open Access Journals (Sweden)

Chernaya Anastassiya

2015-01-01

Full Text Available The paper intends to give an overview of a computer-aided design program application. The research includes two main parts: the development of a computer-aided design for an appropriate switchgear selection and its arrangement in an indoor switchgear layout. Matlab program was used to develop a computer-aided design system. The use of this program considerably simplifies the selection and arrangement of 10 kV switchgear.

Enabling Lean Design Through Computer Aided Synthesis: The Injection Moulding Cooling Case

NARCIS (Netherlands)

Jauregui Becker, Juan Manuel; Wits, Wessel Willems

2015-01-01

This paper explores the application of Computer Aided Synthesis (CAS) to support the implementation of Set-Based Concurrent Engineering (SBCE) and Just In Time Decision Making (JIT-DM), which are considered as two of the cornerstones of the Lean Design method. Computer Aided Synthesis refers to a

Computer Aided Design Tools for Extreme Environment Electronics, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This project aims to provide Computer Aided Design (CAD) tools for radiation-tolerant, wide-temperature-range digital, analog, mixed-signal, and radio-frequency...

DEVELOPMENT OF A CHEST FREEZER – OPTIMUM DESIGN OF AN EVAPORATOR COIL

Directory of Open Access Journals (Sweden)

K. Kalyani Radha

2012-06-01

Full Text Available In a country such as India, food grains, fruit, vegetables, meat, poultry and fish, are very susceptible to microbial contamination and spoilage and require stringent preservation methods. One such method is by the use of a chest freezer for the storage of frozen food. This investigation considers different loads and design parameters for the development of a chest freezer using R134a as the working fluid. Experimental designs of an evaporator coil, condenser coil and capillary tube are investigated through the development of storage periods in terms of steady state and cyclic performance, by optimising the quantity of refrigerant charge, with strict adherence to the standards and requirement for maintaining an internal temperature of -23 °C at 43 °C ambient. Cyclic load performance tests optimise the performance of individual components selected for the design of a chest freezer. The system selection has a highly balanced performance with R134a and showed 118 kJ/kg cooling capacity with 8.42 coefficient of performance (COP. By the replacement of R134a, temperatures of -23 °C are maintained inside the freezer cabinet with low power consumption and an increase in the net refrigerating effect, which in turn increases the COP. The system design has optimum efficiency with moderate costs by optimising the length and diameter of the evaporator coil, i.e., 34.15 m and 7.94 mm, respectively.

Computer Aided Design and Analysis of Separation Processes with Electrolyte Systems

DEFF Research Database (Denmark)

A methodology for computer aided design and analysis of separation processes involving electrolyte systems is presented. The methodology consists of three main parts. The thermodynamic part "creates" the problem specific property model package, which is a collection of pure component and mixture...... property models. The design and analysis part generates process (flowsheet) alternatives, evaluates/analyses feasibility of separation and provides a visual operation path for the desired separation. The simulation part consists of a simulation/calculation engine that allows the screening and validation...... of process alternatives. For the simulation part, a general multi-purpose, multi-phase separation model has been developed and integrated to an existing computer aided system. Application of the design and analysis methodology is highlighted through two illustrative case studies....

Computer Aided Design and Analysis of Separation Processes with Electrolyte Systems

DEFF Research Database (Denmark)

Takano, Kiyoteru; Gani, Rafiqul; Kolar, P.

2000-01-01

A methodology for computer aided design and analysis of separation processes involving electrolyte systems is presented. The methodology consists of three main parts. The thermodynamic part 'creates' the problem specific property model package, which is a collection of pure component and mixture...... property models. The design and analysis part generates process (flowsheet) alternatives, evaluates/analyses feasibility of separation and provides a visual operation path for the desired separation. The simulation part consists of a simulation/calculation engine that allows the screening and validation...... of process alternatives. For the simulation part, a general multi-purpose, multi-phase separation model has been developed and integrated to an existing computer aided system. Application of the design and analysis methodology is highlighted through two illustrative case studies, (C) 2000 Elsevier Science...

Designing optimum diameter of skip shafts in mines with inclined or steep coal seams

Energy Technology Data Exchange (ETDEWEB)

Durov, E.M.

1981-07-01

This paper discusses methods of increasing depth of operating shaft mines considering optimization of hoisting systems. The following solutions are analyzed: removing mined rock material to the surface, to operating horizon, to the deepest horizon, removing rock to the deepest horizon by enlarging a large diameter borehole. It is suggested that removing rock material to the surface is most economical. This solution is sometimes difficult to implement due to design of mine shafts. If a shaft is equipped with two pairs of skips, or with a pair of skips and two independent skips, one skip or a pair of skips can be removed to form free space for buckets used to hoist mined rock and coal. The bucket moves along rope shaft guides. Analysis of the optimum hoisting systems in shaft mines for coal mines with the following design capacity is carried out: 0.9, 1.2, 1.5 and 1.8 Mmt a year. The following depth of working horizons is evaluated: 600, 800, 1000, 1200, 1400 and 1600 m. It is assumed that coal and rock are hoisted separately. Advance rate ranges from 10 to 50 m/month. The results of analysis are shown in two tables. It is suggested that from the point of view of increasing depth of active mine shafts the following solutions are optimum: 7 m shaft with a system of three independently moving skips (two for coal, one for rock material), and 8 m shaft equipped with a pair of skips and two independent skips (one of the independently moving skips is used for rock hoisting). 4 refs.

Teaching Computer-Aided Design of Fluid Flow and Heat Transfer Engineering Equipment.

Science.gov (United States)

Gosman, A. D.; And Others

1979-01-01

Describes a teaching program for fluid mechanics and heat transfer which contains both computer aided learning (CAL) and computer aided design (CAD) components and argues that the understanding of the physical and numerical modeling taught in the CAL course is essential to the proper implementation of CAD. (Author/CMV)

Design and operation of the national home health aide survey: 2007-2008.

Science.gov (United States)

Bercovitz, Anita; Moss, Abigail J; Sengupta, Manisha; Harris-Kojetin, Lauren D; Squillace, Marie R; Emily, Rosenoff; Branden, Laura

2010-03-01

This report provides an overview of the National Home Health Aide Survey (NHHAS), the first national probability survey of home health aides. NHHAS was designed to provide national estimates of home health aides who provided assistance in activities of daily living (ADLs) and were directly employed by agencies that provide home health and/or hospice care. This report discusses the need for and objectives of the survey, the design process, the survey methods, and data availability. METHODS NHHAS, a multistage probability sample survey, was conducted as a supplement to the 2007 National Home and Hospice Care Survey (NHHCS). Agencies providing home health and/or hospice care were sampled, and then aides employed by these agencies were sampled and interviewed by telephone. Survey topics included recruitment, training, job history, family life, client relations, work-related injuries, and demographics. NHHAS was virtually identical to the 2004 National Nursing Assistant Survey of certified nursing assistants employed in sampled nursing homes with minor changes to account for differences in workplace environment and responsibilities. RESULTS From September 2007 to April 2008, interviews were completed with 3,416 aides. A public-use data file that contains the interview responses, sampling weights, and design variables is available. The NHHAS overall response rate weighted by the inverse of the probability of selection was 41 percent. This rate is the product of the weighted first-stage agency response rate of 57 percent (i.e., weighted response rate of 59 percent for agency participation in NHHCS times the weighted response rate of 97 percent for agencies participating in NHHCS that also participated in NHHAS) and the weighted second-stage aide response rate of 72 percent to NHHAS.

Geometric modeling for computer aided design

Science.gov (United States)

Schwing, James L.; Olariu, Stephen

1995-01-01

The primary goal of this grant has been the design and implementation of software to be used in the conceptual design of aerospace vehicles particularly focused on the elements of geometric design, graphical user interfaces, and the interaction of the multitude of software typically used in this engineering environment. This has resulted in the development of several analysis packages and design studies. These include two major software systems currently used in the conceptual level design of aerospace vehicles. These tools are SMART, the Solid Modeling Aerospace Research Tool, and EASIE, the Environment for Software Integration and Execution. Additional software tools were designed and implemented to address the needs of the engineer working in the conceptual design environment. SMART provides conceptual designers with a rapid prototyping capability and several engineering analysis capabilities. In addition, SMART has a carefully engineered user interface that makes it easy to learn and use. Finally, a number of specialty characteristics have been built into SMART which allow it to be used efficiently as a front end geometry processor for other analysis packages. EASIE provides a set of interactive utilities that simplify the task of building and executing computer aided design systems consisting of diverse, stand-alone, analysis codes. Resulting in a streamlining of the exchange of data between programs reducing errors and improving the efficiency. EASIE provides both a methodology and a collection of software tools to ease the task of coordinating engineering design and analysis codes.

Preliminary study of optimum ductburning turbofan engine cycle design parameters for supersonic cruising

Science.gov (United States)

Fishbach, L. H.

1978-01-01

The effect of turbofan engine overall pressure ratio, fan pressure ratio, and ductburner temperature rise on the engine weight and cruise fuel consumption for a mach 2.4 supersonic transport was investigated. Design point engines, optimized purely for the supersonic cruising portion of the flight where the bulk of the fuel is consumed, are considered. Based on constant thrust requirements at cruise, fuel consumption considerations would favor medium by pass ratio engines (1.5 to 1.8) of overall pressure ratio of about 16. Engine weight considerations favor low bypass ratio (0.6 or less) and low wverall pressure ratio (8). Combination of both effects results in bypass ratios of 0.6 to 0.8 and overall pressure ratio of 12 being the overall optimum.

Determination of optimum mixing time for raw materials with the tracer method in the glass industry

Energy Technology Data Exchange (ETDEWEB)

Gallyas, M; Gemesi, J; Kurinka, J

1983-02-01

The authors explain how the optimum mixing time for the raw materials for glass manufacture can be determined with the aid of the radioactive tracer method. Basing themselves on measurements, they indicate the change in the degree of mixing of the individual components (soda (Na-24), sodium sulphate, coke (La-140) and bone meal (P-32) as a function of mixing time. The optimum degree of mixing and mixing time for dry and for wet mixing are determined. Finally, data for determining the permissible storage time of the mixture are given.

[Computer aided design for fixed partial denture framework based on reverse engineering technology].

Science.gov (United States)

Sun, Yu-chun; Lü, Pei-jun; Wang, Yong

2006-03-01

To explore a computer aided design (CAD) route for the framework of domestic fixed partial denture (FPD) and confirm the suitable method of 3-D CAD. The working area of a dentition model was scanned with a 3-D mechanical scanner. Using the reverse engineering (RE) software, margin and border curves were extracted and several reference curves were created to ensure the dimension and location of pontic framework that was taken from the standard database. The shoulder parts of the retainers were created after axial surfaces constructed. The connecting areas, axial line and curving surface of the framework connector were finally created. The framework of a three-unit FPD was designed with RE technology, which showed smooth surfaces and continuous contours. The design route is practical. The result of this study is significant in theory and practice, which will provide a reference for establishing the computer aided design/computer aided manufacture (CAD/CAM) system of domestic FPD.

Framework for Computer-Aided Evolution of Object-Oriented Designs

NARCIS (Netherlands)

Ciraci, S.; van den Broek, P.M.; Aksit, Mehmet

2008-01-01

In this paper, we describe a framework for the computer aided evolution of the designs of object-oriented software systems. Evolution mechanisms are software structures that prepare software for certain type of evolutions. The framework uses a database which holds the evolution mechanisms, modeled

Optimum design of a Lanchester damper for a viscously damped single degree of freedom system subjected to inertial excitation

Science.gov (United States)

Bapat, V. A.; Prabhu, P.

1980-11-01

The problem of designing an optimum Lanchester damper for a viscously damped single degree of freedom system subjected to inertial harmonic excitation is investigated. Two criteria are used for optimizing the performance of the damper: (i) minimum motion transmissibility; (ii) minimum force transmissibility. Explicit expressions are developed for determining the absorber parameters.

Dual-scan technique for the customization of zirconia computer-aided design/computer-aided manufacturing frameworks.

Science.gov (United States)

Andreiuolo, Rafael Ferrone; Sabrosa, Carlos Eduardo; Dias, Katia Regina H Cervantes

2013-09-01

The use of bi-layered all-ceramic crowns has continuously grown since the introduction of computer-aided design/computer-aided manufacturing (CAD/CAM) zirconia cores. Unfortunately, despite the outstanding mechanical properties of zirconia, problems related to porcelain cracking or chipping remain. One of the reasons for this is that ceramic copings are usually milled to uniform thicknesses of 0.3-0.6 mm around the whole tooth preparation. This may not provide uniform thickness or appropriate support for the veneering porcelain. To prevent these problems, the dual-scan technique demonstrates an alternative that allows the restorative team to customize zirconia CAD/CAM frameworks with adequate porcelain thickness and support in a simple manner.

33 CFR 66.05-10 - State waters for private aids to navigation; designations; revisions, and revocations.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false State waters for private aids to... Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION PRIVATE AIDS TO NAVIGATION State Aids to Navigation § 66.05-10 State waters for private aids to navigation; designations; revisions, and...

Computer aided design of solonoid magnets

Energy Technology Data Exchange (ETDEWEB)

DeOlivares, J.M.

1978-06-01

Computer programs utilizing Legendre functions and elliptic integral functions have been written to aid in the design of solenoid magnets. The field inside an axisymmetric magnet can be expanded in a converging power series of Legendre functions. The Legendre function approach is very useful for designing solenoid magnets with a high degree of field uniformity. This approach has been programed on the LBL CDC 7600 computer so that one can design an axisymmetric magnet which meets any desired field structure. Two examples of computer designed solenoids are presented. A computer program utilizing elliptic integral functions was also written for the LBL CDC 7600 computer. This method was used in a computer program to verify the results obtained from the Legendre approach and for field calculations within the conductor. The elliptic integral field calculations within the conductor showed that thin solenoids produce field peaking at the ends of the magnet. Computer data is generated for various magnet geometries and compared with theoretical predictions. Computer results and theoretical prediction both show that field peaking is reduced for longer coils, increased for thinner coils and field peaking is a logarithmic function of length, thickness and radius.

Hardware synthesis from DDL. [Digital Design Language for computer aided design and test of LSI

Science.gov (United States)

Shah, A. M.; Shiva, S. G.

1981-01-01

The details of the digital systems can be conveniently input into the design automation system by means of Hardware Description Languages (HDL). The Computer Aided Design and Test (CADAT) system at NASA MSFC is used for the LSI design. The Digital Design Language (DDL) has been selected as HDL for the CADAT System. DDL translator output can be used for the hardware implementation of the digital design. This paper addresses problems of selecting the standard cells from the CADAT standard cell library to realize the logic implied by the DDL description of the system.

Recent advances in the reconstruction of cranio-maxillofacial defects using computer-aided design/computer-aided manufacturing.

Science.gov (United States)

Oh, Ji-Hyeon

2018-12-01

With the development of computer-aided design/computer-aided manufacturing (CAD/CAM) technology, it has been possible to reconstruct the cranio-maxillofacial defect with more accurate preoperative planning, precise patient-specific implants (PSIs), and shorter operation times. The manufacturing processes include subtractive manufacturing and additive manufacturing and should be selected in consideration of the material type, available technology, post-processing, accuracy, lead time, properties, and surface quality. Materials such as titanium, polyethylene, polyetheretherketone (PEEK), hydroxyapatite (HA), poly-DL-lactic acid (PDLLA), polylactide-co-glycolide acid (PLGA), and calcium phosphate are used. Design methods for the reconstruction of cranio-maxillofacial defects include the use of a pre-operative model printed with pre-operative data, printing a cutting guide or template after virtual surgery, a model after virtual surgery printed with reconstructed data using a mirror image, and manufacturing PSIs by directly obtaining PSI data after reconstruction using a mirror image. By selecting the appropriate design method, manufacturing process, and implant material according to the case, it is possible to obtain a more accurate surgical procedure, reduced operation time, the prevention of various complications that can occur using the traditional method, and predictive results compared to the traditional method.

Veterans Like Me: Formative evaluation of a patient decision aid design.

Science.gov (United States)

Gibson, Bryan; Butler, Jorie; Doyon, Katherine; Ellington, Lee; Bray, Bruce E; Zeng, Qing

2017-07-01

Patient decision aids are tools intended to facilitate shared decision-making. Currently development of a patient decision aid is resource intensive: it requires a decision-specific review of the scientific literature by experts to ascertain the potential outcomes under different treatments. The goal of this project was to conduct a formative evaluation of a generalizable, scalable decision aid component we call Veterans Like Me (VLme). VLme mines EHR data to present the outcomes of individuals "like you" on different treatments to the user. These outcome are presented through a combination of an icon array and simulated narratives. Twenty-six patients participated in semi-structured interviews intended to elicit feedback on the tool's functional and interface design. The interview focused on the filters users desired with which to make cases similar to them, the kinds of outcomes they wanted presented, and their envisioned use of the tool. The interview also elicited participants information needs and salient factors related to the therapeutic decision. The interview transcripts were analyzed using an iteratively refined coding schema and content analysis. . Participants generally expressed enthusiasm for the tool's design and functionality. Our analysis identified desired filters for users to view patients like themselves, outcome types that should be included in future iterations of the tool (e.g. patient reported outcomes), and information needs that need to be addressed for patients to effectively participate in shared decision making. Implications for the integration of our findings into the design of patient decision aids are discussed. Published by Elsevier Inc.

Value-based design for the elderly: An application in the field of mobility aids.

Science.gov (United States)

Boerema, Simone T; van Velsen, Lex; Vollenbroek-Hutten, Miriam M R; Hermens, Hermie J

2017-01-01

In the aging society, the need for the elderly to remain mobile and independent is higher than ever. However, many aids supporting mobility often fail to target real needs and lack acceptance. The aim of this study is to demonstrate how value-based design can contribute to the design of mobility aids that address real needs and thus, lead to high acceptance. We elicited values, facilitators, and barriers of mobility of older adults via ten in-depth interviews. Next, we held co-creation sessions, resulting in several designs of innovative mobility aids, which were evaluated for acceptance via nine in-depth interviews. The interviews resulted in a myriad of key values, such as "independence from family" and "doing their own groceries." Design sessions resulted in three designs for a wheeled walker. Their acceptance was rather low. Current mobility device users were more eager to accept the designs than non-users. The value-based approach offers designers a close look into the lives of the elderly, thereby opening up a wide range of innovation possibilities that better fit their actual needs. Product service systems seem to be a promising focus for targeting human needs in mobility device design.

Choosing the optimum burnup

International Nuclear Information System (INIS)

Geller, L.; Goldstein, L.; Franks, W.A.

1986-01-01

This paper reviews some of the considerations utilities must evaluate when going to higher discharge burnups. The advantages and disadvantages of higher discharge burnups are described, as well as a consistent approach for evaluating optimum discharge burnup and its comparison to current practice. When an analysis is performed over the life of the plant, the design of the terminal cycles has significant impact on the lifetime savings from higher burnups. Designs for high burnup cycles have a greater average inventory value in the core. As one goes to higher burnup, there is a greater likelihood of discarding a larger value in unused fuel unless the terminal cycles are designed carefully. This effect can be large enough in some cases to wipe out the lifetime cost savings relative to operating with a higher discharge burnup cycle

Designing Visual Aids That Promote Risk Literacy: A Systematic Review of Health Research and Evidence-Based Design Heuristics.

Science.gov (United States)

Garcia-Retamero, Rocio; Cokely, Edward T

2017-06-01

Background Effective risk communication is essential for informed decision making. Unfortunately, many people struggle to understand typical risk communications because they lack essential decision-making skills. Objective The aim of this study was to review the literature on the effect of numeracy on risk literacy, decision making, and health outcomes, and to evaluate the benefits of visual aids in risk communication. Method We present a conceptual framework describing the influence of numeracy on risk literacy, decision making, and health outcomes, followed by a systematic review of the benefits of visual aids in risk communication for people with different levels of numeracy and graph literacy. The systematic review covers scientific research published between January 1995 and April 2016, drawn from the following databases: Web of Science, PubMed, PsycINFO, ERIC, Medline, and Google Scholar. Inclusion criteria were investigation of the effect of numeracy and/or graph literacy, and investigation of the effect of visual aids or comparison of their effect with that of numerical information. Thirty-six publications met the criteria, providing data on 27,885 diverse participants from 60 countries. Results Transparent visual aids robustly improved risk understanding in diverse individuals by encouraging thorough deliberation, enhancing cognitive self-assessment, and reducing conceptual biases in memory. Improvements in risk understanding consistently produced beneficial changes in attitudes, behavioral intentions, trust, and healthy behaviors. Visual aids were found to be particularly beneficial for vulnerable and less skilled individuals. Conclusion Well-designed visual aids tend to be highly effective tools for improving informed decision making among diverse decision makers. We identify five categories of practical, evidence-based guidelines for heuristic evaluation and design of effective visual aids.

33 CFR 66.05-100 - Designation of navigable waters as State waters for private aids to navigation.

Science.gov (United States)

2010-07-01

... as State waters for private aids to navigation. 66.05-100 Section 66.05-100 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY AIDS TO NAVIGATION PRIVATE AIDS TO NAVIGATION State Aids to Navigation § 66.05-100 Designation of navigable waters as State waters for private aids to...

Simulation of optimum parameters for GaN MSM UV photodetector

Energy Technology Data Exchange (ETDEWEB)

Alhelfi, Mohanad A., E-mail: mhad12344@gmail.com; Ahmed, Naser M., E-mail: nas-tiji@yahoo.com; Hashim, M. R., E-mail: roslan@usm.my; Hassan, Z., E-mail: zai@usm.my [Institue of Nano-Optoelectronics Research and Technology (INOR), School of Physics, Universiti Sains Malaysia 11800 Penang (Malaysia); Al-Rawi, Ali Amer, E-mail: aliamer@unimap.edu.my [School of Computer and Communication Eng. 3st Floor, Pauh Putra Main Campus 02600 Arau, Perlis Malaysia (Malaysia)

2016-07-06

In this study the optimum parameters of GaN M-S-M photodetector are discussed. The evaluation of the photodetector depends on many parameters, the most of the important parameters the quality of the GaN film and others depend on the geometry of the interdigited electrode. In this simulation work using MATLAB software with consideration of the reflection and absorption on the metal contacts, a detailed study involving various electrode spacings (S) and widths (W) reveals conclusive results in device design. The optimum interelectrode design for interdigitated MSM-PD has been specified and evaluated by effect on quantum efficiency and responsivity.

Optimum value engineering and integrated design methods for reducing the cost of R-2000 houses

Energy Technology Data Exchange (ETDEWEB)

Proskiw, G. [Proskiw Engineering Ltd., Winnipeg, MB (Canada); Parekh, A. [Natural Resources Canada, Ottawa, ON (Canada)

2009-07-01

Opportunities exist to reduce the incremental cost of R-2000 construction by using optimum value engineering (OVE) and integrated design (ID) techniques. OVE is a construction philosophy in which components and systems are designed to meet their intended purposes without excessive or unnecessary use of resources. This paper summarized a study that was designed to identify opportunities for reducing the costs of R-2000 houses while improving their performance. These included detailed energy and cost analysis of various OVE/ID options which were then applied to a sample of 18 representative new home designs from British Columbia, Manitoba, and New Brunswick. The paper described the OVE/ID measures studied, cost analysis, measure utilization and energy analysis. It also included a detailed discussion of individual OVE/ID measures. Examples of some of these measures were the elimination of floor system cross-bridging; support of non-load bearing partition walls; engineered wood beams; drywall clips at corners; and non-load bearing partition walls. It was concluded that significant opportunities exist to reduce the incremental cost of R-2000 houses through careful application of OVE and ID practices. 5 refs., 4 tabs., 1 fig.

Computer Aided Design of Kaplan Turbine Piston with\tSolidWorks

Directory of Open Access Journals (Sweden)

Camelia Jianu

2010-10-01

Full Text Available The paper presents the steps for 3D computer aided design (CAD of Kaplan turbine piston made in SolidWorks.The present paper is a tutorial for a Kaplan turbine piston 3D geometry, which is dedicaded to the Parts Sketch and Parts Features design and Drawing Geometry and Drawing Annotation.

Computer-aided design of the RF-cavity for a high-power S-band klystron

Science.gov (United States)

Kant, D.; Bandyopadhyay, A. K.; Pal, D.; Meena, R.; Nangru, S. C.; Joshi, L. M.

2012-08-01

This article describes the computer-aided design of the RF-cavity for a S-band klystron operating at 2856 MHz. State-of-the-art electromagnetic simulation tools SUPERFISH, CST Microwave studio, HFSS and MAGIC have been used for cavity design. After finalising the geometrical details of the cavity through simulation, it has been fabricated and characterised through cold testing. Detailed results of the computer-aided simulation and cold measurements are presented in this article.

CADRIGS--computer aided design reliability interactive graphics system

International Nuclear Information System (INIS)

Kwik, R.J.; Polizzi, L.M.; Sticco, S.; Gerrard, P.B.; Yeater, M.L.; Hockenbury, R.W.; Phillips, M.A.

1982-01-01

An integrated reliability analysis program combining graphic representation of fault trees, automated data base loadings and reference, and automated construction of reliability code input files was developed. The functional specifications for CADRIGS, the computer aided design reliability interactive graphics system, are presented. Previously developed fault tree segments used in auxiliary feedwater system safety analysis were constructed on CADRIGS and, when combined, yielded results identical to those resulting from manual input to the same reliability codes

Determining the optimum process parameter for grinding operations using robust process

International Nuclear Information System (INIS)

Neseli, Suley Man; Asilturk, Ilhan; Celik, Levent

2012-01-01

We applied combined response surface methodology (RSM) and Taguchi methodology (TM) to determine optimum parameters for minimum surface roughness (Ra) and vibration (Vb) in external cylindrical grinding. First, an experiment was conducted in a CNC cylindrical grinding machine. The TM using L 27 orthogonal array was applied to the design of the experiment. The three input parameters were workpiece revolution, feed rate and depth of cut; the outputs were vibrations and surface roughness. Second, to minimize wheel vibration and surface roughness, two optimized models were developed using computer aided single objective optimization. The experimental and statistical results revealed that the most significant grinding parameter for surface roughness and vibration is workpiece revolution followed by the depth of cut. The predicted values and measured values were fairly close, which indicates 2 ( 94.99 R 2Ra =and 2 92.73) R 2Vb =that the developed models can be effectively used to predict surface roughness and vibration in the grinding. The established model for determination of optimal operating conditions shows that a hybrid approach can lead to success of a robust process

A new decomposition-based computer-aided molecular/mixture design methodology for the design of optimal solvents and solvent mixtures

DEFF Research Database (Denmark)

Karunanithi, A.T.; Achenie, L.E.K.; Gani, Rafiqul

2005-01-01

This paper presents a novel computer-aided molecular/mixture design (CAMD) methodology for the design of optimal solvents and solvent mixtures. The molecular/mixture design problem is formulated as a mixed integer nonlinear programming (MINLP) model in which a performance objective is to be optim......This paper presents a novel computer-aided molecular/mixture design (CAMD) methodology for the design of optimal solvents and solvent mixtures. The molecular/mixture design problem is formulated as a mixed integer nonlinear programming (MINLP) model in which a performance objective...... is to be optimized subject to structural, property, and process constraints. The general molecular/mixture design problem is divided into two parts. For optimal single-compound design, the first part is solved. For mixture design, the single-compound design is first carried out to identify candidates...... and then the second part is solved to determine the optimal mixture. The decomposition of the CAMD MINLP model into relatively easy to solve subproblems is essentially a partitioning of the constraints from the original set. This approach is illustrated through two case studies. The first case study involves...

The influence of a yacht's heeling stability on optimum sail design

Science.gov (United States)

Sneyd, A. D.; Sugimoto, T.

1997-01-01

This paper presents fundamental results concerning the optimum design of yacht sails and masts. The aerodynamics of a high aspect ratio sail in uniform flow is analysed using lifting line theory to maximise thrust for a given sail area. The novel feature of this work is that thrust is optimised subject to the constraint that the aerodynamic heeling moment generated by the sail is balanced by the righting moment due to hull buoyancy (and the weight of the keel). Initially, the heel angle is therefore unknown, and determined as part of the solution process. Under the assumption of small heel angle, the problem reduces to minimising a quadratic form in the Fourier coefficients for the circulation distribution along the mast, and a simple analytic solution can be derived. It is found that if the mast is too high, the upper section is unused, and as a consequence there is a theoretically ideal mast height for a yacht of given heeling stability. Under the constraints of given sail area and heeling equilibrium it is found that no advantage is to be gained by allowing reverse circulation near the top of the mast. Various implications for yacht performance are discussed.

Low-floor bus design preferences of walking aid users during simulated boarding and alighting.

Science.gov (United States)

D'souza, Clive; Paquet, Victor; Lenker, James; Steinfeld, Edward; Bareria, Piyush

2012-01-01

Low-floor buses represent a significant improvement in accessible public transit for passengers with limited mobility. However, there is still a need for research on the inclusive design of transit buses to identify specific low-floor bus design conditions that are either particularly accommodating or challenging for passengers with functional and mobility impairments. These include doorway locations, seating configuration and the large front wheel-well covers that collectively impact boarding, alighting and interior movement of passengers. Findings from a laboratory study using a static full-scale simulation of a lowfloor bus to evaluate the impact of seating configuration and crowding on interior movement and accessibility for individuals with and without walking aids are presented (n=41). Simulated bus journeys that included boarding, fare payment, seating, and alighting were performed. Results from video observations and subjective assessments showed differences in boarding and alighting performance and users' perceptions of task difficulty. The need for assistive design features (e.g. handholds, stanchions), legroom and stowage space for walking aids was evident. These results demonstrate that specific design conditions in low-floor buses can significantly impact design preference among those who use walking aids. Consideration of ergonomics and inclusive design can therefore be used to improve the design of low-floor buses.

Simulation programs for ph.D. study of analysis, modeling and optimum design of solar domestic hot water systems

Energy Technology Data Exchange (ETDEWEB)

Lin Qin

1998-12-31

The design of solar domestic hot water (DHW) systems is a complex process, due to characteristics inherent in the solar heating technology. Recently, computer simulation has become a widely used technique to improve the understanding of the thermal processes in such systems. One of the main objects of the Ph.D. study of `Analysis, Modelling and optimum Design of Solar Domestic Hot Water Systems` is to develop and verify programs for carrying out the simulation and evaluation of the dynamic performance of solar DHW systems. During this study, simulation programs for hot water distribution networks and for certain types of solar DHW systems were developed. (au)

Adhesive Bonding to Computer-aided Design/ Computer-aided Manufacturing Esthetic Dental Materials: An Overview.

Science.gov (United States)

Awad, Mohamed Moustafa; Alqahtani, H; Al-Mudahi, A; Murayshed, M S; Alrahlah, A; Bhandi, Shilpa H

2017-07-01

To review the adhesive bonding to different computer-aided design/computer-aided manufacturing (CAD/CAM) esthetic restorative materials. The use of CAD/CAM esthetic restorative materials has gained popularity in recent years. Several CAD/ CAM esthetic restorative materials are commercially available. Adhesive bonding is a major determinant of success of CAD/ CAM restorations. Review result: An account of the currently available bonding strategies are discussed with their rationale in various CAD/ CAM materials. Different surface treatment methods as well as adhesion promoters can be used to achieve reliable bonding of CAD/CAM restorative materials. Selection of bonding strategy to such material is determined based on its composition. Further evidence is required to evaluate the effect of new surface treatment methods, such as nonthermal atmospheric plasma and self-etching ceramic primer on bonding to different dental ceramics. An understanding of the currently available bonding strategies to CA/CAM materials can help the clinician to select the most indicated system for each category of materials.

Computer-aided approach for design of tailor-made blended products

DEFF Research Database (Denmark)

Yunus, Nor Alafiza; Gernaey, Krist; Woodley, John

2012-01-01

A computer-aided methodology has been developed for the design of blended (mixture) products. Through this methodology, it is possible to identify the most suitable chemicals for blending, and “tailor” the blend according to specified product needs (usually product attributes, e.g. performance...... as well as regulatory). The product design methodology has four tasks. First, the design problem is defined: the product needs are identified, translated into target properties and the constraints for each target property are defined. Secondly, target property models are retrieved from a property model...

[Key points for esthetic rehabilitation of anterior teeth using chair-side computer aided design and computer aided manufacture technique].

Science.gov (United States)

Yang, J; Feng, H L

2018-04-09

With the rapid development of the chair-side computer aided design and computer aided manufacture (CAD/CAM) technology, its accuracy and operability of have been greatly improved in recent years. Chair-side CAD/CAM system may produce all kinds of indirect restorations, and has the advantages of rapid, accurate and stable production. It has become the future development direction of Stomatology. This paper describes the clinical application of the chair-side CAD/CAM technology for anterior aesthetic restorations from the aspects of shade and shape.

Cognitive task analysis and the design of computerized operator aids

International Nuclear Information System (INIS)

Andersson, H.

1985-01-01

The new technological possibilities have led to the initiation of many projects for the design and evaluation of computerized operator support systems to be implemented in nuclear power plant control rooms. A typical finding so far has been that operators often have a positive attitude towards such systems but still don't use them very much, mostly because they find almost the same information on the conventional control boards which they are accustomed to use. Still, however, there is a widely shared belief that conventional control rooms have short-comings that make the use of computerized aids necessary. One reason for the limited success so far is that the new systems often are poorly integrated with the existing conventional instrumentation and with the working procedures. The reluctance to use new computer based aids, despite their nice features, is therefore probably caused by an inadequate task analysis made prior to the design of these computerized operator support systems

Optimum body size of Holstein replacement heifers.

Science.gov (United States)

Hoffman, P C

1997-03-01

Criteria that define optimum body size of replacement heifers are required by commercial dairy producers to evaluate replacement heifer management programs. Historically recommended body size criteria have been based on live BW measurements. Numerous research studies have observed a positive relationship between BW at first calving and first lactation milk yield, which has served as the impetus for using live BW to define body size of replacement heifers. Live BW is, however, not the only available measurement to define body size. Skeletal measurements such as wither height, length, and pelvic area have been demonstrated to be related to first lactation performance and (or) dystocia. Live BW measurements also do not define differences in body composition. Differences in body composition of replacement heifers at first calving are also related to key performance variables. An updated research data base is available for the modern Holstein genotype to incorporate measures of skeletal growth and body composition with BW when defining body size. These research projects also lend insight into the relative importance of measurements that define body size of replacement heifers. Incorporation of these measurements from current research into present BW recommendations should aid commercial dairy producers to better define replacement heifer growth and management practices. This article proposes enhancements in defining optimum body size and growth characteristics of Holstein replacement heifers.

Analysis of three-phase power-supply systems using computer-aided design programs

International Nuclear Information System (INIS)

Oberst, E.F.

1977-01-01

A major concern of every designer of large, three-phase power-supply systems is the protection of system components from overvoltage transients. At present, three computer-aided circuit design programs are available in the Magnetic Fusion Energy (MFE) National Computer Center that can be used to analyze three-phase power systems: MINI SCEPTRE, SPICE I, and SPICE II. These programs have been used at Lawrence Livermore Laboratory (LLL) to analyze the operation of a 200-kV dc, 20-A acceleration power supply for the High Voltage Test Stand. Various overvoltage conditions are simulated and the effectiveness of system protective devices is observed. The simulated overvoltage conditions include such things as circuit breaker openings, pulsed loading, and commutation voltage surges in the rectifiers. These examples are used to illustrate the use of the computer-aided, circuit-design programs discussed in this paper

User Centered Design as a Framework for Applying Conversation Analysis in Hearing Aid Consultations

DEFF Research Database (Denmark)

Egbert, Maria; Matthews, Ben

2011-01-01

collaboration, as well as successes and pitfalls. In particular we focus on the role of conversation analysists both from the perspective of the designers and the conversation analysts. To illustrate this, we have selected a project on hearing aid fitting. To understand the perspective of the users (the person...... with hearing loss and the hearing aid fitter is imperative because the compliance rate for hearing aid use is staggeringly low. One of the barriers of hearing aid use lies in problematic encounters between the person with hearing loss and audiologists. Buur, J and Matthews, B. (2008) ‘Participatory Innovation...

Correction of facial and mandibular asymmetry using a computer aided design/computer aided manufacturing prefabricated titanium implant.

Science.gov (United States)

Watson, Jason; Hatamleh, Muhanad; Alwahadni, Ahed; Srinivasan, Dilip

2014-05-01

Patients with significant craniofacial asymmetry may have functional problems associated with their occlusion and aesthetic concerns related to the imbalance in soft and hard tissue profiles. This report details a case of facial asymmetry secondary to left mandible angle deficiency due to undergoing previous radiotherapy. We describe the correction of the bony deformity using computer aided design/computer aided manufacturing custom-made titanium onlay using novel direct metal laser sintering. The direct metal laser sintering onlay proved a very accurate operative fit and showed a good aesthetic correction of the bony defect with no reported complications postoperatively. It is a useful low-morbidity technique, and there is no resorption or associated donor-site complications.

Computer-aided design of microvasculature systems for use in vascular scaffold production

International Nuclear Information System (INIS)

Mondy, William Lafayette; Cameron, Don; Timmermans, Jean-Pierre; De Clerck, Nora; Sasov, Alexander; Casteleyn, Christophe; Piegl, Les A

2009-01-01

In vitro biomedical engineering of intact, functional vascular networks, which include capillary structures, is a prerequisite for adequate vascular scaffold production. Capillary structures are necessary since they provide the elements and compounds for the growth, function and maintenance of 3D tissue structures. Computer-aided modeling of stereolithographic (STL) micro-computer tomographic (micro-CT) 3D models is a technique that enables us to mimic the design of vascular tree systems containing capillary beds, found in tissues. In our first paper (Mondy et al 2009 Tissue Eng. at press), using micro-CT, we studied the possibility of using vascular tissues to produce data capable of aiding the design of vascular tree scaffolding, which would help in the reverse engineering of a complete vascular tree system including capillary bed structures. In this paper, we used STL models of large datasets of computer-aided design (CAD) data of vascular structures which contained capillary structures that mimic those in the dermal layers of rabbit skin. Using CAD software we created from 3D STL models a bio-CAD design for the development of capillary-containing vascular tree scaffolding for skin. This method is designed to enhance a variety of therapeutic protocols including, but not limited to, organ and tissue repair, systemic disease mediation and cell/tissue transplantation therapy. Our successful approach to in vitro vasculogenesis will allow the bioengineering of various other types of 3D tissue structures, and as such greatly expands the potential applications of biomedical engineering technology into the fields of biomedical research and medicine.

Computer-aided design of microvasculature systems for use in vascular scaffold production

Energy Technology Data Exchange (ETDEWEB)

Mondy, William Lafayette [Department of Chemical and Biomedical Engineering, University of South Florida, FL (United States); Cameron, Don [Department of Pathology and Cell Biology, College of Medicine, University of South Florida, FL (United States); Timmermans, Jean-Pierre [Department of Veterinary Sciences, University of Antwerp (Belgium); De Clerck, Nora [Department of Biomedical Sciences University of Antwerp (Belgium); Sasov, Alexander [Skyscan (Belgium); Casteleyn, Christophe [College of Veterinary Medicine, Ghent University (Belgium); Piegl, Les A [Department of Computer Science and Engineering, University of South Florida, FL (United States)

2009-09-15

In vitro biomedical engineering of intact, functional vascular networks, which include capillary structures, is a prerequisite for adequate vascular scaffold production. Capillary structures are necessary since they provide the elements and compounds for the growth, function and maintenance of 3D tissue structures. Computer-aided modeling of stereolithographic (STL) micro-computer tomographic (micro-CT) 3D models is a technique that enables us to mimic the design of vascular tree systems containing capillary beds, found in tissues. In our first paper (Mondy et al 2009 Tissue Eng. at press), using micro-CT, we studied the possibility of using vascular tissues to produce data capable of aiding the design of vascular tree scaffolding, which would help in the reverse engineering of a complete vascular tree system including capillary bed structures. In this paper, we used STL models of large datasets of computer-aided design (CAD) data of vascular structures which contained capillary structures that mimic those in the dermal layers of rabbit skin. Using CAD software we created from 3D STL models a bio-CAD design for the development of capillary-containing vascular tree scaffolding for skin. This method is designed to enhance a variety of therapeutic protocols including, but not limited to, organ and tissue repair, systemic disease mediation and cell/tissue transplantation therapy. Our successful approach to in vitro vasculogenesis will allow the bioengineering of various other types of 3D tissue structures, and as such greatly expands the potential applications of biomedical engineering technology into the fields of biomedical research and medicine.

Computer-aided design of microvasculature systems for use in vascular scaffold production.

Science.gov (United States)

Mondy, William Lafayette; Cameron, Don; Timmermans, Jean-Pierre; De Clerck, Nora; Sasov, Alexander; Casteleyn, Christophe; Piegl, Les A

2009-09-01

In vitro biomedical engineering of intact, functional vascular networks, which include capillary structures, is a prerequisite for adequate vascular scaffold production. Capillary structures are necessary since they provide the elements and compounds for the growth, function and maintenance of 3D tissue structures. Computer-aided modeling of stereolithographic (STL) micro-computer tomographic (micro-CT) 3D models is a technique that enables us to mimic the design of vascular tree systems containing capillary beds, found in tissues. In our first paper (Mondy et al 2009 Tissue Eng. at press), using micro-CT, we studied the possibility of using vascular tissues to produce data capable of aiding the design of vascular tree scaffolding, which would help in the reverse engineering of a complete vascular tree system including capillary bed structures. In this paper, we used STL models of large datasets of computer-aided design (CAD) data of vascular structures which contained capillary structures that mimic those in the dermal layers of rabbit skin. Using CAD software we created from 3D STL models a bio-CAD design for the development of capillary-containing vascular tree scaffolding for skin. This method is designed to enhance a variety of therapeutic protocols including, but not limited to, organ and tissue repair, systemic disease mediation and cell/tissue transplantation therapy. Our successful approach to in vitro vasculogenesis will allow the bioengineering of various other types of 3D tissue structures, and as such greatly expands the potential applications of biomedical engineering technology into the fields of biomedical research and medicine.

[Initial evolution research for design and process accuracy of one type of domestic computer aided design soft and computer aided manufacture].

Science.gov (United States)

Song, Yang; Zhao, Yi-jiao; Sun, Yu-chun; Lü, Pei-jun; Wang, Yong

2013-09-01

To evaluate the design and manufacture accuracy of a domestic computer aided design (CAD) and computer aided manufacture (CAM) system, and to compare it with similar foreign products. Thirty models of posterior-teeth-single-crown preparations were collected, and STL data of these preparations was collected by Denmark 3Shape scanner. Three copings were made for each preparation, the one designed and manufactured using commercial CAD/CAM system (3Shape CAD software and Wieland T1 CAM equipment) was assigned into control group T0, the one designed and manufactured using domestic CAD software (developed by Peking University School and Hospital of Stomatology and Nanjing University of Aeronautics and Astronautics) and Wieland T1 CAM equipment was assigned into experimental group TCAD for design accuracy evaluation, and the one designed and manufactured using 3Shape CAD software and domestic CAM equipment (developed by Peking University School and Hospital of Stomatology, Tsinghua University and ShanDong XinHua Incorporated Company of medical apparatus and instruments) was assigned into experimental group TCAM for manufacture accuracy evaluation. Finally, the marginal fitness were compared and evaluated by using 3D & Profile measurement microscope laser. The marginal fitness of TCAD was 27.98 (19.10, 46.57) µm in buccal, 32.67 (20.65, 50.82) µm in lingual, 27.38 (22.53, 52.61) µm in mesial, 29.50 (22.68, 53.65) µm in distal; of TCAM was 21.69 (15.87, 30.21) µm in buccal, 18.51 (13.50, 22.51) µm in lingual, 19.15 (15.42, 26.89) µm in mesial, 22.77 (18.58, 32.15) µm in distal; and there were no statistical differences compared with T0 [20.16 (17.16, 48.00) µm in buccal, 21.51 (17.05, 28.31) µm in lingual, 23.54 (17.89, 30.04) µm in mesial and 23.94 (17.93, 28.19) µm in distal] except lingual data of TCAD. The design and machining precision of this domestic CAD/CAM system is at the same level of those comparable foreign products.

Optimum fiber distribution in singlewall corrugated fiberboard

Science.gov (United States)

Millard W. Johnson; Thomas J. Urbanik; William E. Denniston

1979-01-01

Determining optimum distribution of fiber through rational design of corrugated fiberboard could result in significant reductions in fiber required to meet end-use conditions, with subsequent reductions in price pressure and extension of the softwood timber supply. A theory of thin plates under large deformations is developed that is both kinematically and physically...

A Learning Aid Tool for Power Electronics Converters

Directory of Open Access Journals (Sweden)

O. Bouketir

2005-06-01

Full Text Available It is known that power electronics and its related subjects are not easy to understand for students taking them for first time. This is due to nature of the subjects which involve many areas and disciplines. The introduction of general purpose simulation package has helped the student a step further in understanding this subject. However, because of the generality of these tools and their drag-and drop and ad-hoc features, the students still face problems in designing a converter circuit. In this paper, the problem above is addressed by introducing a learning aid tool that guides the student over prescribed steps to design a power electronics circuit. The tool is knowledge-based system where its knowledge base encompasses two types of knowledge; topologies and switching devices. The first step in the design procedure is the selection of the application of the desired circuit. Then few steps are to be followed to come out with the appropriate topology with the optimum switching devices and parameters. System structure, its different modules and the detailed design procedure are explained in this paper

Optimum design of matrix fault current limiters using the series resistance connected with shunt coil

Science.gov (United States)

Chung, D. C.; Choi, H. S.; Lee, N. Y.; Nam, G. Y.; Cho, Y. S.; Sung, T. H.; Han, Y. H.; Kim, B. S.; Lim, S. H.

2007-10-01

In this paper we described the improved design for the matrix fault current limiters (MFCL). To do this, we used thin film-type superconducting elements. therefore it means that we can make the MFCL with minimized size and high switching speed because of the high current density and the high indexing value of superconducting thin film. Also we could minimize the bulky shunt coil using the connection of a series resistance with a shunt coil. Also we could effectively block up a leakage current in shunt coils under no-fault condition and simply control total impedances of a current-limiting part using this method. After we designed an appropriated 1 × 2 basic MFCL module with an applied voltage of 160 V, we enlarged it to a 2 × 2 MFCL module and a 3 × 2 MFCL module where applied voltages were 320 V and 480 V, respectively. Experimental results for our MFCL were reported in terms of various fault currents, variation of series resistance and so on. We think that these methods will be useful in the optimum design of an m × n MFCL.

Optimum design of matrix fault current limiters using the series resistance connected with shunt coil

International Nuclear Information System (INIS)

Chung, D.C.; Choi, H.S.; Lee, N.Y.; Nam, G.Y.; Cho, Y.S.; Sung, T.H.; Han, Y.H.; Kim, B.S.; Lim, S.H.

2007-01-01

In this paper we described the improved design for the matrix fault current limiters (MFCL). To do this, we used thin film-type superconducting elements. therefore it means that we can make the MFCL with minimized size and high switching speed because of the high current density and the high indexing value of superconducting thin film. Also we could minimize the bulky shunt coil using the connection of a series resistance with a shunt coil. Also we could effectively block up a leakage current in shunt coils under no-fault condition and simply control total impedances of a current-limiting part using this method. After we designed an appropriated 1 x 2 basic MFCL module with an applied voltage of 160 V, we enlarged it to a 2 x 2 MFCL module and a 3 x 2 MFCL module where applied voltages were 320 V and 480 V, respectively. Experimental results for our MFCL were reported in terms of various fault currents, variation of series resistance and so on. We think that these methods will be useful in the optimum design of an m x n MFCL

Overview of SDCM - The Spacecraft Design and Cost Model

Science.gov (United States)

Ferebee, Melvin J.; Farmer, Jeffery T.; Andersen, Gregory C.; Flamm, Jeffery D.; Badi, Deborah M.

1988-01-01

The Spacecraft Design and Cost Model (SDCM) is a computer-aided design and analysis tool for synthesizing spacecraft configurations, integrating their subsystems, and generating information concerning on-orbit servicing and costs. SDCM uses a bottom-up method in which the cost and performance parameters for subsystem components are first calculated; the model then sums the contributions from individual components in order to obtain an estimate of sizes and costs for each candidate configuration within a selected spacecraft system. An optimum spacraft configuration can then be selected.

The effects of computer-aided design software on engineering students' spatial visualisation skills

Science.gov (United States)

Kösa, Temel; Karakuş, Fatih

2018-03-01

The purpose of this study was to determine the influence of computer-aided design (CAD) software-based instruction on the spatial visualisation skills of freshman engineering students in a computer-aided engineering drawing course. A quasi-experimental design was applied, using the Purdue Spatial Visualization Test-Visualization of Rotations (PSVT:R) for both the pre- and the post-test. The participants were 116 freshman students in the first year of their undergraduate programme in the Department of Mechanical Engineering at a university in Turkey. A total of 72 students comprised the experimental group; they were instructed with CAD-based activities in an engineering drawing course. The control group consisted of 44 students who did not attend this course. The results of the study showed that a CAD-based engineering drawing course had a positive effect on developing engineering students' spatial visualisation skills. Additionally, the results of the study showed that spatial visualisation skills can be a predictor for success in a computer-aided engineering drawing course.

Optimum design for effective water transport through a double-layered porous hydrogel inspired by plant leaves

Science.gov (United States)

Kim, Hyejeong; Kim, Hyeonjeong; Huh, Hyungkyu; Hwang, Hyung Ju; Lee, Sang Joon

2014-11-01

Plant leaves are generally known to have optimized morphological structure in response to environmental changes for efficient water usage. However, the advantageous features of plant leaves are not fully utilized in engineering fields yet, since the optimum design in internal structure of plant leaves is unclear. In this study, the tissue organization of the hydraulic pathways inside plant leaves was investigated. Water transport through double-layered porous hydrogel models analogous to mesophyll cells was experimentally observed. In addition, computational experiment and theoretical analysis were applied to the model systems to find the optimal design for efficient water transport. As a result, the models with lower porosity or with pores distributed widely in the structure exhibit efficient mass transport. Our theoretical prediction supports that structural features of plant leaves guarantee sufficient water supply as survival strategy. This study may provide a new framework for investigating the biophysical principles governing the morphological optimization of plant leaves and for designing microfluidic devices to enhance mass transport ability. This study was supported by the National Research Foundation of Korea and funded by the Korean government.

Uniform and Non-Uniform Optimum Scalar Quantizers Performances: A Comparative Study

Directory of Open Access Journals (Sweden)

Fendy Santoso

2008-05-01

Full Text Available The aim of this research is to investigate source coding, the representation of information source output by finite R bits/symbol. The performance of optimum quantisers subject to an entropy constraint has been studied. The definitive work in this area is best summarised by Shannon’s source coding theorem, that is, a source with entropy H can be encoded with arbitrarily small error probability at any rate R (bits/source output as long as R>H. Conversely, If R the error probability will be driven away from zero, independent of the complexity of the encoder and the decoder employed. In this context, the main objective of engineers is however to design the optimum code. Unfortunately, the rate-distortion theorem does not provide the recipe for such a design. The theorem does, however, provide the theoretical limit so that we know how close we are to the optimum. The full understanding of the theorem also helps in setting the direction to achieve such an optimum. In this research, we have investigated the performances of two practical scalar quantisers, i.e., a Lloyd-Max quantiser and the uniformly defined one and also a well-known entropy coding scheme, i.e., Huffman coding against their theoretically attainable optimum performance due to Shannon’s limit R. It has been shown that our uniformly defined quantiser could demonstrate superior performance. The performance improvements, in fact, are more noticeable at higher bit rates.

The future of computer-aided design and engineering at CERN

CERN Document Server

Høimyr, Nils-Joar

2004-01-01

This working note discusses design and engineering processes at CERN and Computer Aided Design and Engineering tools. The main focus of this note is Mechanical design and CAE activities and how to share and organize the data produced by CAD/CAE tools. These issues cannot be addressed without taking a global view of the engineering activities at CERN. As more and more of the detailed design work is done by external suppliers, the design processes at CERN change. Traditional design work where draftsmen are producing drawings on the request from engineers is replaced by conceptual design work done by domain specialists and engineers. Furthermore CAD and FEM tools have evolved from specialist tools to mainstream utilities mastered by most engineers. Design activities nowadays can now be carried out directly by the project engineer without the use of a design (drawing) office. This environment poses different requirements for design- and engineering support activities as well as the selection of CAE-tools. Design ...

The optimum spanning catenary cable

Science.gov (United States)

Wang, C. Y.

2015-03-01

A heavy cable spans two points in space. There exists an optimum cable length such that the maximum tension is minimized. If the two end points are at the same level, the optimum length is 1.258 times the distance between the ends. The optimum lengths for end points of different heights are also found.

Computer-aided design of biological circuits using TinkerCell.

Science.gov (United States)

Chandran, Deepak; Bergmann, Frank T; Sauro, Herbert M

2010-01-01

Synthetic biology is an engineering discipline that builds on modeling practices from systems biology and wet-lab techniques from genetic engineering. As synthetic biology advances, efficient procedures will be developed that will allow a synthetic biologist to design, analyze, and build biological networks. In this idealized pipeline, computer-aided design (CAD) is a necessary component. The role of a CAD application would be to allow efficient transition from a general design to a final product. TinkerCell is a design tool for serving this purpose in synthetic biology. In TinkerCell, users build biological networks using biological parts and modules. The network can be analyzed using one of several functions provided by TinkerCell or custom programs from third-party sources. Since best practices for modeling and constructing synthetic biology networks have not yet been established, TinkerCell is designed as a flexible and extensible application that can adjust itself to changes in the field. © 2010 Landes Bioscience

Analysis of near optimum design for small and medium size nuclear power plants

International Nuclear Information System (INIS)

Ahmed, A.A.

1977-01-01

Market surveys in recent years have shown that a significant market would exist among the developing nations of the world for nuclear power plants that would be classified as small to medium sized, provided that these small plants could produce electricity at a unit price comparable to that of equivalent sized fossil fired plants. Nuclear plants in the range of 100 MWe to 500 MWe would fit more effectively into the relatively smaller grids of most developing nations than would the 900 MWe to 1300 MWe units now being constructed in the large industrial nations. Worldwide re-evaluation of the worth of fossil fuels has prompted a re-examination of the competitive position of small to medium sized nuclear generating units compared to comparable fossil fired units, especially in the context of units specifically optimized for the size range of interest, rather than of designs that are simply scaled down versions of the currently available larger units. Since the absolute cost of electricity is more sensitive to external factors such as cost of money, national inflation rate and time required for licensing and construction than to details of design or perhaps even to choice of fuels, and since the cost of electricity generated in small to medium sized fossil fired units is periodically compared to that of scaled down versions of conventional large nuclear units, the point of view taken here is one of comparing the relative generating costs of smaller nuclear units of optimum design with the corresponding costs of scaled down versions of current large nuclear generating units

Optimum Design of a Nonlinear Vibration Absorber Coupled to a Resonant Oscillator: A Case Study

Directory of Open Access Journals (Sweden)

H. F. Abundis-Fong

2018-01-01

Full Text Available This paper presents the optimal design of a passive autoparametric cantilever beam vibration absorber for a linear mass-spring-damper system subject to harmonic external force. The design of the autoparametric vibration absorber is obtained by using an approximation of the nonlinear frequency response function, computed via the multiple scales method. Based on the solution given by the perturbation method mentioned above, a static optimization problem is formulated in order to determine the optimum parameters (mass and length of the nonlinear absorber which minimizes the steady state amplitude of the primary mass under resonant conditions; then, a PZT actuator is cemented to the base of the beam, so the nonlinear absorber is made active, thus enabling the possibility of controlling the effective stiffness associated with the passive absorber and, as a consequence, the implementation of an active vibration control scheme able to preserve, as possible, the autoparametric interaction as well as to compensate varying excitation frequencies and parametric uncertainty. Finally, some simulations and experimental results are included to validate and illustrate the dynamic performance of the overall system.

Optimum heat storage design for heat integrated multipurpose batch plants

CSIR Research Space (South Africa)

Stamp, J

2011-01-01

Full Text Available procedure is presented tha journal homepage: www All rights reserved. ajozi T, Optimum heat storage grated multipurpose batch plants , South Africa y usage in multipurpose batch plants has been in published literature most present methods, time... � 2pL?u?kins ? 1 h3A3?u?cu?U (36) The internal area for heat loss by convection from the heat transfer medium is given by Constraint (37) and the area for convective heat transfer losses to the environment is given in Constraint (38). A1?u? ? 2...

Optimum heat storage design for SDHWsystems

DEFF Research Database (Denmark)

Shah, Louise Jivan; Furbo, Simon

1997-01-01

-in spiral. The other model is especially designed for low flow SDHWsystems based on a mantle tank.The tank design's influence on the thermal performance of the SDHWsystems has been investigated in a way where only one tank parameter has been changed at a time in the calculations. In this way a direct......Two simulation models have been used to analyse the heat storage design's influence on the thermal performance of solar domestic hot water systems, SDHWsystems. One model is especially designed for traditional SDHWsystems based on a heat storage design where the solar heat exchanger is a built...

Determining the optimum process parameter for grinding operations using robust process

Energy Technology Data Exchange (ETDEWEB)

Neseli, Suley Man; Asilturk, Ilhan; Celik, Levent [Univ. of Selcuk, Konya (Turkmenistan)

2012-11-15

We applied combined response surface methodology (RSM) and Taguchi methodology (TM) to determine optimum parameters for minimum surface roughness (Ra) and vibration (Vb) in external cylindrical grinding. First, an experiment was conducted in a CNC cylindrical grinding machine. The TM using L{sup 27} orthogonal array was applied to the design of the experiment. The three input parameters were workpiece revolution, feed rate and depth of cut; the outputs were vibrations and surface roughness. Second, to minimize wheel vibration and surface roughness, two optimized models were developed using computer aided single objective optimization. The experimental and statistical results revealed that the most significant grinding parameter for surface roughness and vibration is workpiece revolution followed by the depth of cut. The predicted values and measured values were fairly close, which indicates 2 ( 94.99 R{sup 2Ra}=and 2 92.73) R{sup 2Vb}=that the developed models can be effectively used to predict surface roughness and vibration in the grinding. The established model for determination of optimal operating conditions shows that a hybrid approach can lead to success of a robust process.

Design and fabrication of a sleep apnea device using computer-aided design/additive manufacture technologies.

Science.gov (United States)

Al Mortadi, Noor; Eggbeer, Dominic; Lewis, Jeffrey; Williams, Robert J

2013-04-01

The aim of this study was to analyze the latest innovations in additive manufacture techniques and uniquely apply them to dentistry, to build a sleep apnea device requiring rotating hinges. Laser scanning was used to capture the three-dimensional topography of an upper and lower dental cast. The data sets were imported into an appropriate computer-aided design software environment, which was used to design a sleep apnea device. This design was then exported as a stereolithography file and transferred for three-dimensional printing by an additive manufacture machine. The results not only revealed that the novel computer-based technique presented provides new design opportunities but also highlighted limitations that must be addressed before the techniques can become clinically viable.

Nondissipative optimum charge regulator

Science.gov (United States)

Rosen, R.; Vitebsky, J. N.

1970-01-01

Optimum charge regulator provides constant level charge/discharge control of storage batteries. Basic power transfer and control is performed by solar panel coupled to battery through power switching circuit. Optimum controller senses battery current and modifies duty cycle of switching circuit to maximize current available to battery.

New Method and Software for Computer-Aided Flowsheet Design and Analysis

DEFF Research Database (Denmark)

K.Tula, Anjan; Gani, Rafiqul; Eden, Mario R.

2017-01-01

in the same way as atoms or groups of atoms are synthesized to form molecules in computer aided molecular design (CAMD) techniques. Another important aspect of this method is the integration of economic, sustainability and LCA analyses in the early stages of process synthesis to identify process hotspots...

Estimation of the failure risk of a maxillary premolar with different crack depths with endodontic treatment by computer-aided design/computer-aided manufacturing ceramic restorations.

Science.gov (United States)

Lin, Chun-Li; Chang, Yen-Hsiang; Hsieh, Shih-Kai; Chang, Wen-Jen

2013-03-01

This study evaluated the risk of failure for an endodontically treated premolar with different crack depths, which was shearing toward the pulp chamber and was restored by using 3 different computer-aided design/computer-aided manufacturing ceramic restoration configurations. Three 3-dimensional finite element models designed with computer-aided design/computer-aided manufacturing ceramic onlay, endocrown, and conventional crown restorations were constructed to perform simulations. The Weibull function was incorporated with finite element analysis to calculate the long-term failure probability relative to different load conditions. The results indicated that the stress values on the enamel, dentin, and luting cement for endocrown restorations exhibited the lowest values relative to the other 2 restoration methods. Weibull analysis revealed that the overall failure probabilities in a shallow cracked premolar were 27%, 2%, and 1% for the onlay, endocrown, and conventional crown restorations, respectively, in the normal occlusal condition. The corresponding values were 70%, 10%, and 2% for the depth cracked premolar. This numeric investigation suggests that the endocrown provides sufficient fracture resistance only in a shallow cracked premolar with endodontic treatment. The conventional crown treatment can immobilize the premolar for different cracked depths with lower failure risk. Copyright © 2013 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

User-centered design and the development of patient decision aids: protocol for a systematic review.

Science.gov (United States)

Witteman, Holly O; Dansokho, Selma Chipenda; Colquhoun, Heather; Coulter, Angela; Dugas, Michèle; Fagerlin, Angela; Giguere, Anik Mc; Glouberman, Sholom; Haslett, Lynne; Hoffman, Aubri; Ivers, Noah; Légaré, France; Légaré, Jean; Levin, Carrie; Lopez, Karli; Montori, Victor M; Provencher, Thierry; Renaud, Jean-Sébastien; Sparling, Kerri; Stacey, Dawn; Vaisson, Gratianne; Volk, Robert J; Witteman, William

2015-01-26

Providing patient-centered care requires that patients partner in their personal health-care decisions to the full extent desired. Patient decision aids facilitate processes of shared decision-making between patients and their clinicians by presenting relevant scientific information in balanced, understandable ways, helping clarify patients' goals, and guiding decision-making processes. Although international standards stipulate that patients and clinicians should be involved in decision aid development, little is known about how such involvement currently occurs, let alone best practices. This systematic review consisting of three interlinked subreviews seeks to describe current practices of user involvement in the development of patient decision aids, compare these to practices of user-centered design, and identify promising strategies. A research team that includes patient and clinician representatives, decision aid developers, and systematic review method experts will guide this review according to the Cochrane Handbook and PRISMA reporting guidelines. A medical librarian will hand search key references and use a peer-reviewed search strategy to search MEDLINE, EMBASE, PubMed, Web of Science, the Cochrane Library, the ACM library, IEEE Xplore, and Google Scholar. We will identify articles across all languages and years describing the development or evaluation of a patient decision aid, or the application of user-centered design or human-centered design to tools intended for patient use. Two independent reviewers will assess article eligibility and extract data into a matrix using a structured pilot-tested form based on a conceptual framework of user-centered design. We will synthesize evidence to describe how research teams have included users in their development process and compare these practices to user-centered design methods. If data permit, we will develop a measure of the user-centeredness of development processes and identify practices that are likely

Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aoyama, K.; Sawada, K. [The University of Tokyo, Tokyo (Japan)

1996-12-31

Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

Basic studies on computer aided concurrent engineering for hull structure design and piping design; Kakugi ittai wo koryoshita doji heikotekina sekkei no shien ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

Aoyama, K; Sawada, K [The University of Tokyo, Tokyo (Japan)

1997-12-31

Considering integrated hull and piping design in shipbuilding industry as a good example for concurrent engineering (CE), discussions were given on a computer aided method to perform integrated hull and piping design smoothly. When CE aiding by means of a computer is considered, it is important to discuss a method for information management not only for `utilization of product models`, but also for `maintaining consistency between items of product information` and `concurrent utilization and production of product information` in concurrent designs. For the CE aided information management, utilization and production of the product information is effective if restrictive relationship between items of product information, and design functions are made clear. Definitions were given on the restrictive relationship between items of product information and `restrictive relationship information` that has `decision/provisional decision`, `date and time`, `designer` and `design functions`. Furthermore, `comprehensive relationship between items of product information` that can be produced from the restrictive relationship information was defined as a `restrictive network`. Utilizing the restrictive relationship between items of product information for CE aiding is effective. 9 refs., 14 figs.

Computer-aided design of bromelain and papain covalent immobilization

OpenAIRE

Bessy Cutiño-Avila; Dayrom Gil Pradas; Carlos Aragón Abreu; Yuniel Fernández Marrero; Martha Hernández de la Torre; Emir Salas Sarduy; María de los Ángeles Chávez Planes; José Manuel Guisán Seijas; Joaquín Díaz Brito; Alberto del Monte-Martínez

2014-01-01

Título en español: Diseño asistido por computadora de la inmovilización covalente de bromelina y papaína. Título corto: Computer-aided design of bromelain and papain.  Abstract: Enzymes as immobilized derivatives have been widely used in Food, Agrochemical, Pharmaceutical and Biotechnological industries. Protein immobilization is probably the most used technology to improve the operational stability of these molecules. Bromelain (Ananas comosus) and papain (Carica papaya) are cystein pr...

Tailor-made Design of Chemical Blends using Decomposition-based Computer-aided Approach

DEFF Research Database (Denmark)

Yunus, Nor Alafiza; Manan, Zainuddin Abd.; Gernaey, Krist

(properties). In this way, first the systematic computer-aided technique establishes the search space, and then narrows it down in subsequent steps until a small number of feasible and promising candidates remain and then experimental work may be conducted to verify if any or all the candidates satisfy......Computer aided technique is an efficient approach to solve chemical product design problems such as design of blended liquid products (chemical blending). In chemical blending, one tries to find the best candidate, which satisfies the product targets defined in terms of desired product attributes...... is decomposed into two stages. The first stage investigates the mixture stability where all unstable mixtures are eliminated and the stable blend candidates are retained for further testing. In the second stage, the blend candidates have to satisfy a set of target properties that are ranked according...

Using the Continuum of Design Modelling Techniques to Aid the Development of CAD Modeling Skills in First Year Industrial Design Students

Science.gov (United States)

Storer, I. J.; Campbell, R. I.

2012-01-01

Industrial Designers need to understand and command a number of modelling techniques to communicate their ideas to themselves and others. Verbal explanations, sketches, engineering drawings, computer aided design (CAD) models and physical prototypes are the most commonly used communication techniques. Within design, unlike some disciplines,…

Optimum Design of Braced Steel Space Frames including Soil-Structure Interaction via Teaching-Learning-Based Optimization and Harmony Search Algorithms

OpenAIRE

Ayse T. Daloglu; Musa Artar; Korhan Ozgan; Ali İ. Karakas

2018-01-01

Optimum design of braced steel space frames including soil-structure interaction is studied by using harmony search (HS) and teaching-learning-based optimization (TLBO) algorithms. A three-parameter elastic foundation model is used to incorporate the soil-structure interaction effect. A 10-storey braced steel space frame example taken from literature is investigated according to four different bracing types for the cases with/without soil-structure interaction. X, V, Z, and eccentric V-shaped...

Application of computer aided tolerance analysis in product design

International Nuclear Information System (INIS)

Du Hua

2009-01-01

This paper introduces the shortage of the traditional tolerance design method and the strong point of the computer aided tolerancing (CAT) method,compares the shortage and the strong point among the three tolerance analysis methods, which are Worst Case Analysis, Statistical Analysis and Monte-Carlo Simulation Analysis, and offers the basic courses and correlative details for CAT. As the study objects, the reactor pressure vessel, the core barrel, the hold-down barrel and the support plate are used to upbuild the tolerance simulation model, based on their 3D design models. Then the tolerance simulation analysis has been conducted and the scheme of the tolerance distribution is optimized based on the analysis results. (authors)

[Veneer computer aided design based on reverse engineering technology].

Science.gov (United States)

Liu, Ming-li; Chen, Xiao-dong; Wang, Yong

2012-03-01

To explore the computer aided design (CAD) method of veneer restoration, and to assess if the solution can help prosthesis meet morphology esthetics standard. A volunteer's upper right central incisor needed to be restored with veneer. Super hard stone models of patient's dentition (before and after tooth preparation) were scanned with the three-dimensional laser scanner. The veneer margin was designed as butt-to-butt type. The veneer was constructed using reverse engineering (RE) software. The technique guideline of veneers CAD was explore based on RE software, and the veneers was smooth, continuous and symmetrical, which met esthetics construction needs. It was a feasible method to reconstruct veneer restoration based on RE technology.

Expert systems for design, operation and management of industrial plant elctrical systems

Energy Technology Data Exchange (ETDEWEB)

Delfino, B.; Forzano, P.; Invernizzi, M.; Massucco, S. (Genoa Univ. (Italy) Pavia Univ. (Italy) Ansaldo Industria, Genoa (Italy))

1991-02-01

A discussion is made of modern industrial plant requirements with regard to man-machine interfacing. Indications are then given as to the optimum hardware and software for electrical plant and process control systems. Illustrative examples are provided on the use of expert systems to aid in the design of industrial plant electrical systems and to allow safe and reliable on-line control and monitoring.

Computer-aided design studies of the homopolar linear synchronous motor

Science.gov (United States)

Dawson, G. E.; Eastham, A. R.; Ong, R.

1984-09-01

The linear induction motor (LIM), as an urban transit drive, can provide good grade-climbing capabilities and propulsion/braking performance that is independent of steel wheel-rail adhesion. In view of its 10-12 mm airgap, the LIM is characterized by a low power factor-efficiency product of order 0.4. A synchronous machine offers high efficiency and controllable power factor. An assessment of the linear homopolar configuration of this machine is presented as an alternative to the LIM. Computer-aided design studies using the finite element technique have been conducted to identify a suitable machine design for urban transit propulsion.

Design system for in-vessel mainipulator of fusion reactor 'DESIM'

International Nuclear Information System (INIS)

Adachi, Junihci; Kobayashi, Takeshi; Ise, Hideo; Sato, Keisuke; Matsuda, Hirotsugu

1989-01-01

A computer aided design system 'DESIM' for the in-vessel manipulators of nuclear fusion reactors has been developed to design the manipulators efficiently. The DESIM consists of the following subsystems: (1) the design system for arm mechanisms to realize optimum manipulation performance in the specified workspace; (2) the robot simulator to study manipulator movement, postures and interference problems; (3) the CAD system which is used to define the structure object data for robots, and the interface system for the data conversion from the CAD system to the robot simulator. The DESIM has been used to design the in-vessel manipulator for the Fusion Experimental Reactor (FER) to confirm the effectiveness. (author)

A conceptual framework for designing micro electrical connectors for hearing aid instruments

DEFF Research Database (Denmark)

Doagou Rad, Saeed; Islam, Aminul; Fuglsang-Philip, M.

2016-01-01

technological advancements have urged them to incorporate increased number of electrical contacts. The current paper presents a conceptual framework for designing and manufacturing novel plug and socket systems for hearing aid instruments by using the state of art manufacturing technologies for micro components...

Efficiency of different techniques of physical flattening by fuel while selection of optimum arrangement of large fast reactor core

International Nuclear Information System (INIS)

Grachev, E.A.; Dejnega, N.L.; Mitin, A.M.

1974-01-01

Results are given of calculations for selecting the parameters of the large fast breeder reactor core (1500 Mw) operating on oxide fuel with a sodium coolant. A complex optimum criterion was selected for energy intensity, energy distribution, breeding ratio and critical load factor, run duration, burning, reactivity variations, influence of CV3, fuel overloads, and calculated fue fuel expenses. The effectivities of various methods for physical grading of fuel (enrichment and composition) were examined in accordance with the optimum criterion. Parameters of reactor cores optimum arrangements are presented. Continuous reactor operation during 0.8-1.0 yr. at energy intensity more than 400 kW was shown to be essential for attaining the optimum chosen. Accounting for the CV3 system and partial fuel overloads, the methods of balancing energy release either by enriching fuel or by changing its composition proved to be almost equally effective. All calculations were performed with the aid of a 18-4-RZ-15B program on the basis of a BNAB-26 constant system [ru

Impacts of optimum cost effective energy efficiency standards

International Nuclear Information System (INIS)

Brancic, A.B.; Peters, J.S.; Arch, M.

1991-01-01

Building Codes are increasingly required to be responsive to social and economic policy concerns. In 1990 the State of Connecticut passes An Act Concerning Global Warming, Public Act 90-219, which mandates the revision of the state building code to require that buildings and building elements be designed to provide optimum cost-effective energy efficiency over the useful life of the building. Further, such revision must meet the American Society of Heating, Refrigerating and Air Conditioning Engineers (ASHRAE) Standard 90.1 - 1989. As the largest electric energy supplier in Connecticut, Northeast Utilities (NU) sponsored a pilot study of the cost effectiveness of alternative building code standards for commercial construction. This paper reports on this study which analyzed design and construction means, building elements, incremental construction costs, and energy savings to determine the optimum cost-effective building code standard. Findings are that ASHRAE 90.1 results in 21% energy savings and alternative standards above it result in significant additional savings. Benefit/cost analysis showed that both are cost effective

Modelling physics detectors in a computer aided design system for simulation purposes

International Nuclear Information System (INIS)

Ahvenainen, J.; Oksakivi, T.; Vuoskoski, J.

1995-01-01

The possibility of transferring physics detector models from computer aided design systems into physics simulation packages like GEANT is receiving increasing attention. The problem of exporting detector models constructed in CAD systems into GEANT is well known. We discuss the problem and describe an application, called DDT, which allows one to design detector models in a CAD system and then transfer the models into GEANT for simulation purposes. (orig.)

Computer aided materials design; Keisanki zairyo sekkei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The questionnaire survey on the computer aided materials design (CAMD), and the survey of current domestic and overseas software concerned were carried out to clarify developmental issues. The current elementary technology of CAMD was also surveyed to study its several problems caused with a progress of material design technology due to drastic diffusion of CAMD. This project aims at establishment of a new demanded software, computer chemistry, focusing attention on functional materials such as catalyst, polymer and non-linear electronic materials. Microscopic simulation technology was mainly surveyed in fiscal 1996. Although some fruitful results have been obtained in the fields of medical and agricultural chemicals, organic compounds, proteins, catalysts and electronic materials, such some problems are pointed out as `CAMD cannot handle an actual size of the target system` and `commercially available software are very expensive.` Reliable tool development as elementary technology, and the verification of its applications are thus required. Meso-dynamics, polymers, surface reaction and integrated technological environment attract users` attention. 27 refs., 16 figs., 2 tabs.

A review of computer-aided design/computer-aided manufacture techniques for removable denture fabrication

Science.gov (United States)

Bilgin, Mehmet Selim; Baytaroğlu, Ebru Nur; Erdem, Ali; Dilber, Erhan

2016-01-01

The aim of this review was to investigate usage of computer-aided design/computer-aided manufacture (CAD/CAM) such as milling and rapid prototyping (RP) technologies for removable denture fabrication. An electronic search was conducted in the PubMed/MEDLINE, ScienceDirect, Google Scholar, and Web of Science databases. Databases were searched from 1987 to 2014. The search was performed using a variety of keywords including CAD/CAM, complete/partial dentures, RP, rapid manufacturing, digitally designed, milled, computerized, and machined. The identified developments (in chronological order), techniques, advantages, and disadvantages of CAD/CAM and RP for removable denture fabrication are summarized. Using a variety of keywords and aiming to find the topic, 78 publications were initially searched. For the main topic, the abstract of these 78 articles were scanned, and 52 publications were selected for reading in detail. Full-text of these articles was gained and searched in detail. Totally, 40 articles that discussed the techniques, advantages, and disadvantages of CAD/CAM and RP for removable denture fabrication and the articles were incorporated in this review. Totally, 16 of the papers summarized in the table. Following review of all relevant publications, it can be concluded that current innovations and technological developments of CAD/CAM and RP allow the digitally planning and manufacturing of removable dentures from start to finish. As a result according to the literature review CAD/CAM techniques and supportive maxillomandibular relationship transfer devices are growing fast. In the close future, fabricating removable dentures will become medical informatics instead of needing a technical staff and procedures. However the methods have several limitations for now. PMID:27095912

Metalloporphyrin catalysts for oxygen reduction developed using computer-aided molecular design

Energy Technology Data Exchange (ETDEWEB)

Ryba, G.N.; Hobbs, J.D.; Shelnutt, J.A. [and others

1996-04-01

The objective of this project is the development of a new class of metalloporphyrin materials used as catalsyts for use in fuel cell applications. The metalloporphyrins are excellent candidates for use as catalysts at both the anode and cathode. The catalysts reduce oxygen in 1 M potassium hydroxide, as well as in 2 M sulfuric acid. Covalent attachment to carbon supports is being investigated. The computer-aided molecular design is an iterative process, in which experimental results feed back into the design of future catalysts.

Computer-aided polymer design using group contribution plus property models

DEFF Research Database (Denmark)

Satyanarayana, Kavitha Chelakara; Abildskov, Jens; Gani, Rafiqul

2009-01-01

. Polymer repeat unit property prediction models are required to calculate the properties of the generated repeat units. A systematic framework incorporating recently developed group contribution plus (GC(+)) models and an extended CAMD technique to include design of polymer repeat units is highlighted...... in this paper. The advantage of a GC(+) model in CAMD applications is that a very large number of polymer structures can be considered even though some of the group parameters may not be available. A number of case studies involving different polymer design problems have been solved through the developed......The preliminary step for polymer product design is to identify the basic repeat unit structure of the polymer that matches the target properties. Computer-aided molecular design (CAMD) approaches can be applied for generating the polymer repeat unit structures that match the required constraints...

Computer-Aided Model Based Analysis for Design and Operation of a Copolymerization Process

DEFF Research Database (Denmark)

Lopez-Arenas, Maria Teresa; Sales-Cruz, Alfonso Mauricio; Gani, Rafiqul

2006-01-01

. This will allow analysis of the process behaviour, contribute to a better understanding of the polymerization process, help to avoid unsafe conditions of operation, and to develop operational and optimizing control strategies. In this work, through a computer-aided modeling system ICAS-MoT, two first......The advances in computer science and computational algorithms for process modelling, process simulation, numerical methods and design/synthesis algorithms, makes it advantageous and helpful to employ computer-aided modelling systems and tools for integrated process analysis. This is illustrated......-principles models have been investigated with respect to design and operational issues for solution copolymerization reactors in general, and for the methyl methacrylate/vinyl acetate system in particular. The Model 1 is taken from literature and is commonly used for low conversion region, while the Model 2 has...

Design of a physical model of the PBMR with the aid of Flownet

International Nuclear Information System (INIS)

Greyvenstein, G.P.; Rousseau, P.G.

2002-01-01

The design of a physical model of the PBMR with the aid of the code Flownet is discussed in this paper. The purpose of the physical model is to test the control strategies and operating procedures of the PBMR and also to demonstrate the accuracy of Flownet. Flownet is first used to do component matching and to determine the detail steady-state performance of the system. It is then demonstrated how the code was used to simulate the start-up procedure as well as a load following and a load rejection scenario. The study demonstrates how a micro model of the PBMR can be designed with the aid of a powerful simulation tool in a relatively short period of time and at low cost using commercially available turbochargers. (author)

Redesigning pH optimum of Geobacillus sp. TF16 endoxylanase through in silico designed DNA swapping strategy.

Science.gov (United States)

Uzuner, Ugur; Canakci, Sabriye; Bektas, Kadriye Inan; Sapmaz, Merve Tuncel; Belduz, Ali Osman

2017-06-01

Thermoalkaliphilic xylanases are highly desired and of great importance due to their vast potential in paper pulp and bleaching processes. Here, we report rapid, cost-effective, and result-oriented combinatorial potential of in silico DNA swapping strategy to engineer the pH optimum of industrially crucial enzymes, particularly engineering of Geobacillus sp. TF16 endoxylanase for alkaline environments. The 3D structures of Geobacillus sp. TF16 and donor Bacillus halodurans C-125 endoxylanases were firstly predicted, analyzed, and compared for their similarities before any in silico design of mutants. Reasonably, to improve its alkaline pH tolerance, the corresponding regions in Geobacillus sp.TF16 endoxylanase were further engineered by swapping with negatively-charged amino acid-rich regions from B. halodurans C-125 endoxylanase. Through only two of four in silico-designed mutants, the optimum pH of GeoTF16 endoxylanase was improved from 8.5 to 10.0. Moreover, as compared to GeoTF16 parental enzyme, both GeoInt3 and GeoInt4 mutants revealed (i) enhanced biobleaching performance, (ii) improved adaptability to alkaline conditions, and (iii) better activity for broader pH range. Unlike GeoTF16 losing activity at pH 11.0 completely, GeoInt4 retained 60% and 40% of its activity at pH 11.0 and 12.0, respectively. Thus, GeoInt4 stands out as a more competent biocatalyst that is suitable for alkaline environments of diverse industrial applications. The current study represents an efficient protein engineering strategy to adapt industrial catalysts to diverse processing conditions. Further comprehensive and fine-tuned research efforts may result in biotechnologically more promising outcomes. Copyright © 2017 Elsevier B.V. and Société Française de Biochimie et Biologie Moléculaire (SFBBM). All rights reserved.

Probabilistic studies for safety at optimum cost

International Nuclear Information System (INIS)

Pitner, P.

1999-01-01

By definition, the risk of failure of very reliable components is difficult to evaluate. How can the best strategies for in service inspection and maintenance be defined to limit this risk to an acceptable level at optimum cost? It is not sufficient to design structures with margins, it is also essential to understand how they age. The probabilistic approach has made it possible to develop well proven concepts. (author)

Implementation of integrated circuit and design of SAR ADC for fully implantable hearing aids.

Science.gov (United States)

Kim, Jong Hoon; Lee, Jyung Hyun; Cho, Jin-Ho

2017-07-20

The hearing impaired population has been increasing; many people suffer from hearing problems. To deal with this difficulty, various types of hearing aids are being rapidly developed. In particular, fully implantable hearing aids are being actively studied to improve the performance of existing hearing aids and to reduce the stigma of hearing loss patients. It has to be of small size and low-power consumption for easy implantation and long-term use. The objective of the study was to implement a small size and low-power consumption successive approximation register analog-to-digital converter (SAR ADC) for fully implantable hearing aids. The ADC was selected as the SAR ADC because its analog circuit components are less required by the feedback circuit of the SAR ADC than the sigma-delta ADC which is conventionally used in hearing aids, and it has advantages in the area and power consumption. So, the circuit of SAR ADC is designed considering the speech region of humans because the objective is to deliver the speech signals of humans to hearing loss patients. If the switch of sample and hold works in the on/off positions, the charge injection and clock feedthrough are produced by a parasitic capacitor. These problems affect the linearity of the hold voltage, and as a result, an error of the bit conversion is generated. In order to solve the problem, a CMOS switch that consists of NMOS and PMOS was used, and it reduces the charge injection because the charge carriers in the NMOS and PMOS have inversed polarity. So, 16 bit conversion is performed before the occurrence of the Least Significant Bit (LSB) error. In order to minimize the offset voltage and power consumption of the designed comparator, we designed a preamplifier with current mirror. Therefore, the power consumption was reduced by the power control switch used in the comparator. The layout of the designed SAR ADC was performed by Virtuoso Layout Editor (Cadence, USA). In the layout result, the size of the

Computer-aided Molecular Design of Compounds Targeting Histone Modifying Enzymes

Science.gov (United States)

Andreoli, Federico; Del Rio, Alberto

2015-01-01

Growing evidences show that epigenetic mechanisms play crucial roles in the genesis and progression of many physiopathological processes. As a result, research in epigenetic grew at a fast pace in the last decade. In particular, the study of histone post-translational modifications encountered an extraordinary progression and many modifications have been characterized and associated to fundamental biological processes and pathological conditions. Histone modifications are the catalytic result of a large set of enzyme families that operate covalent modifications on specific residues at the histone tails. Taken together, these modifications elicit a complex and concerted processing that greatly contribute to the chromatin remodeling and may drive different pathological conditions, especially cancer. For this reason, several epigenetic targets are currently under validation for drug discovery purposes and different academic and industrial programs have been already launched to produce the first pre-clinical and clinical outcomes. In this scenario, computer-aided molecular design techniques are offering important tools, mainly as a consequence of the increasing structural information available for these targets. In this mini-review we will briefly discuss the most common types of known histone modifications and the corresponding operating enzymes by emphasizing the computer-aided molecular design approaches that can be of use to speed-up the efforts to generate new pharmaceutically relevant compounds. PMID:26082827

Design, installation, and initial use of a smart operator aid

International Nuclear Information System (INIS)

Bernard, J.A.; Lau, S.H.; Kwok, Kwan S.; Kim, Keung Koo

1992-01-01

This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-II to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. (author)

Design, installation, and initial use of a smart operator aid

Energy Technology Data Exchange (ETDEWEB)

Bernard, J A; Lau, S H; Kwok, Kwan S; Kim, Keung Koo [Nuclear Reactor Laboratory, Massachusetts Institute of Technology, Cambridge, MA (United States)

1992-07-01

This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-II to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. (author)

Computer-aided design model for anaerobic-phased-solids digester system

Energy Technology Data Exchange (ETDEWEB)

Zhang, Z.; Zhang, R. [University of California, Davis, CA (United States); Tiangco, V. [California Energy Commission, Sacramento, CA (United States)

1999-07-01

The anaerobic-phased-solids (APS) digester system is a newly developed anaerobic digestion system for converting solid wastes, such as crop residues and food wastes, into biogas for power and heat generation. A computer-aided engineering design model has been developed to design the APS-digester system and study the heat transfer from the reactors and energy production of the system. Simulation results of a case study are presented by using the model to predict the heating energy requirement and biogas energy production for anaerobic digestion of garlic waste. The important factors, such as environmental conditions, insulation properties, and characteristics of the wastes, on net energy production are also investigated. (author)

Determination of optimum pressurizer level for kori unit 1

Energy Technology Data Exchange (ETDEWEB)

Song, Dong Soo; Lee, Chang Sup; Yong, Lee Jae; Kim, Yo Han; Lee, Dong Hyuk [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

1998-12-31

To determine the optimum pressurizer water level during normal operation for Kori unit 1, performance and safety analysis are performed. The methodology is developed by evaluating {sup d}ecrease in secondary heat removal{sup e}vents such as Loss of Normal Feedwater accident. To demonstrate optimum pressurizer level setpoint, RETRAN-03 code is used for performance analysis. Analysis results of RETRAN following reactor trip are compared with the actual plant data to justify RETRAN code modelling. The results of performance and safety analyses show that the newly established level setpoints not only improve the performance of pressurizer during transient including reactor trip but also meet the design bases of the pressurizer volume and pressure. 6 refs., 5 figs. (Author)

Determination of optimum pressurizer level for kori unit 1

Energy Technology Data Exchange (ETDEWEB)

Song, Dong Soo; Lee, Chang Sup; Lee Jae Yong; Kim, Yo Han; Lee, Dong Hyuk [Korea Electric Power Research Institute, Taejon (Korea, Republic of)

1997-12-31

To determine the optimum pressurizer water level during normal operation for Kori unit 1, performance and safety analysis are performed. The methodology is developed by evaluating {sup d}ecrease in secondary heat removal{sup e}vents such as Loss of Normal Feedwater accident. To demonstrate optimum pressurizer level setpoint, RETRAN-03 code is used for performance analysis. Analysis results of RETRAN following reactor trip are compared with the actual plant data to justify RETRAN code modelling. The results of performance and safety analyses show that the newly established level setpoints not only improve the performance of pressurizer during transient including reactor trip but also meet the design bases of the pressurizer volume and pressure. 6 refs., 5 figs. (Author)

Value-based design for the elderly : An application in the field of mobility aids

NARCIS (Netherlands)

Boerema, Simone Theresa; van Velsen, Lex Stefan; Vollenbroek-Hutten, Miriam Marie Rosé; Hermens, Hermanus J.

2016-01-01

In the aging society, the need for the elderly to remain mobile and independent is higher than ever. However, many aids supporting mobility often fail to target real needs and lack acceptance. The aim of this study is to demonstrate how value-based design can contribute to the design of mobility

Experiencing an Epidemic: A Seminar Designed To Explore the Spread and Prevention of the AIDS Virus.

Science.gov (United States)

Rochlin, Joyce T.

A seminar was designed to present AIDS (Acquired Immune Deficiency Syndrome) related information to 52 college students enrolled in Psychology 101 courses at Essex Community College in Maryland. First, a questionnaire was administered to determine student knowledge about AIDS. The next part of the procedure was an intervention in the form of a…

A New Optimization Model for Computer-Aided Molecular Design Problems

DEFF Research Database (Denmark)

Zhang, Lei; Cignitti, Stefano; Gani, Rafiqul

Computer-Aided Molecular Design (CAMD) is a method to design molecules with desired properties. That is, through CAMD, it is possible to generate molecules that match a specified set of target properties. CAMD has attracted much attention in recent years due to its ability to design novel as well...... with structure information considered due to the increased size of the mathematical problem and number of alternatives. Thus, decomposition-based approach is proposed to solve the problem. In this approach, only first-order groups are considered in the first step to obtain the building block of the designed...... molecule, then the property model is refined with second-order groups based on the results of the first step. However, this may result in the possibility of an optimal solution being excluded. Samudra and Sahinidis [4] used property relaxation method in the first step to avoid this situation...

Optimum concrete compression strength using bio-enzyme

Directory of Open Access Journals (Sweden)

Bagio Tony Hartono

2017-01-01

Full Text Available To make concrete with high compressive strength and has a certain concrete specifications other than the main concrete materials are also needed concrete mix quality control and other added material is also in line with the current technology of concrete mix that produces concrete with specific characteristics. Addition of bio enzyme on five concrete mixture that will be compared with normal concrete in order to know the optimum level bio-enzyme in concrete to increase the strength of the concrete. Concrete with bio-enzyme 200 ml/m3, 400 ml/m3, 600 ml/m3, 800 ml/m3, 1000 ml/m3 and normal concrete. Refer to the crushing test result, its tends to the mathematical model using 4th degree polynomial regression (least quartic, as represent on the attached data series, which is for the design mix fc′ = 25 MPa generate optimum value for 33,98 MPa, on the bio-additive dosage of 509 ml bio enzymes.

First aid and subsequent measures after radiation accidents

International Nuclear Information System (INIS)

Flach, H.D.

1980-01-01

An organisation schedule and first aid measures after accidents involving ionizing radiation are presented, both in accordance with the current practice of the responsible professional associations. Optimum care also of persons with radiation injuries will be assured by cooperation between voluntary lay helpers, physicians, and regional centres in which failure symptons of the haematopoietic system can be treated. (DG) [de

Optimum Wing Shape of Highly Flexible Morphing Aircraft for Improved Flight Performance

Science.gov (United States)

Su, Weihua; Swei, Sean Shan-Min; Zhu, Guoming G.

2016-01-01

In this paper, optimum wing bending and torsion deformations are explored for a mission adaptive, highly flexible morphing aircraft. The complete highly flexible aircraft is modeled using a strain-based geometrically nonlinear beam formulation, coupled with unsteady aerodynamics and six-degrees-of-freedom rigid-body motions. Since there are no conventional discrete control surfaces for trimming the flexible aircraft, the design space for searching the optimum wing geometries is enlarged. To achieve high performance flight, the wing geometry is best tailored according to the specific flight mission needs. In this study, the steady level flight and the coordinated turn flight are considered, and the optimum wing deformations with the minimum drag at these flight conditions are searched by utilizing a modal-based optimization procedure, subject to the trim and other constraints. The numerical study verifies the feasibility of the modal-based optimization approach, and shows the resulting optimum wing configuration and its sensitivity under different flight profiles.

Optimal Reinsurance Design for Pareto Optimum: From the Perspective of Multiple Reinsurers

Directory of Open Access Journals (Sweden)

Xing Rong

2016-01-01

Full Text Available This paper investigates optimal reinsurance strategies for an insurer which cedes the insured risk to multiple reinsurers. Assume that the insurer and every reinsurer apply the coherent risk measures. Then, we find out the necessary and sufficient conditions for the reinsurance market to achieve Pareto optimum; that is, every ceded-loss function and the retention function are in the form of “multiple layers reinsurance.”

Gathering Empirical Evidence Concerning Links between Computer Aided Design (CAD) and Creativity

Science.gov (United States)

Musta'amal, Aede Hatib; Norman, Eddie; Hodgson, Tony

2009-01-01

Discussion is often reported concerning potential links between computer-aided designing and creativity, but there is a lack of systematic enquiry to gather empirical evidence concerning such links. This paper reports an indication of findings from other research studies carried out in contexts beyond general education that have sought evidence…

Optimum Combining for Rapidly Fading Channels in Ad Hoc Networks

Directory of Open Access Journals (Sweden)

Sonia Furman

2003-10-01

Full Text Available Research and technology in wireless communication systems such as radar and cellular networks have successfully implemented alternative design approaches that utilize antenna array techniques such as optimum combining, to mitigate the degradation effects of multipath in rapid fading channels. In ad hoc networks, these methods have not yet been exploited primarily due to the complexity inherent in the network's architecture. With the high demand for improved signal link quality, devices configured with omnidirectional antennas can no longer meet the growing need for link quality and spectrum efficiency. This study takes an empirical approach to determine an optimum combining antenna array based on 3 variants of interelement spacing. For rapid fading channels, the simulation results show that the performance in the network of devices retrofitted with our antenna arrays consistently exceeded those with an omnidirectional antenna. Further, with the optimum combiner, the performance increased by over 60% compared to that of an omnidirectional antenna in a rapid fading channel.

On Optimum Design of Breakwaters

DEFF Research Database (Denmark)

Burcharth, Hans F.

2005-01-01

Because breakwaters belong to the most important and costly coastal structures it is of importance to optimise the design with respect both to function and lifetime costs. The paper presents a short discussion on choice of type of breakwater and functional aspects. The main content of the paper i...

Modeling electric fields in two dimensions using computer aided design

International Nuclear Information System (INIS)

Gilmore, D.W.; Giovanetti, D.

1992-01-01

The authors describe a method for analyzing static electric fields in two dimensions using AutoCAD. The algorithm is coded in LISP and is modeled after Coloumb's Law. The software platform allows for facile graphical manipulations of field renderings and supports a wide range of hardcopy-output and data-storage formats. More generally, this application is representative of the ability to analyze data that is the solution to known mathematical functions with computer aided design (CAD)

Qualitative analysis of decision making by speech-language pathologists in the design of aided visual displays.

Science.gov (United States)

McFadd, Emily; Wilkinson, Krista

2010-06-01

For children with complex communication needs, augmentative and alternative communication (AAC) devices offer a functional way to communicate thoughts and feelings. Despite many significant advances in the field, effective and efficient aided communication can remain a challenge for some clients and their partners. One critical element of aided AAC intervention is systematic attention to the design of the communication display itself. A well-designed display will foster communication outcomes; a poorly designed one might have the opposite effect. Surprisingly, to our knowledge there are no studies of the strategies that clinicians actually employ when putting together a display. In this research note, we examine, on a case-by-case basis, the strategies six clinicians used when constructing display pages, as a means of highlighting potential areas that might warrant systematic research on display design.

Computer- Aided Design in Power Engineering Application of Software Tools

CERN Document Server

Stojkovic, Zlatan

2012-01-01

This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents  application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel & Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems ...

Design, installation, and initial use of a smart operator aid

International Nuclear Information System (INIS)

Bernard, J.A.; Lau, Shing Hei; Kwok, K.S.; Kim, Keung Koo

1992-01-01

This paper reviews the design, installation, and initial use of a smart operator aid that was developed to assist licensed personnel with the performance of power adjustments on the 5-MWt MIT Research Reactor (MITR-II). The aid is a computer-generated, predictive display that enables console operators to visualize the consequences of a planned control action prior to implementing that action. The motivation for the development of this display was the observation that present-time control decisions are made by comparing a plant's expected behavior to the desired response. Thus, an operator will achieve proper control only to the degree that he or she is capable of anticipating plant response. This may be difficult if the plant's dynamics are non-linear, time delayed, or counter-intuitive. A study was therefore undertaken at the MITR-11 to determine whether operator performance could be improved by using digital technology to provide visual displays of projected plant behavior. It was found that, while the use of predictive information had to be learned, operator performance did improve as a result of its availability. Information is presented on the display's design, the computer system utilized for its implementation, operator response to the display, and the possible extension of this concept to the control of steam generator level. 16 refs., 8 figs

Optimum design of 6-DOF parallel manipulator with translational/rotational workspaces for haptic device application

Energy Technology Data Exchange (ETDEWEB)

Yoon, Jung Won; Hwang, Yoon Kwon [Gyeongsang National University, Jinju (Korea, Republic of); Ryu, Je Ha [Gwangju Institute of Science and Technology, Gwangju (Korea, Republic of)

2010-05-15

This paper proposes an optimum design method that satisfies the desired orientation workspace at the boundary of the translation workspace while maximizing the mechanism isotropy for parallel manipulators. A simple genetic algorithm is used to obtain the optimal linkage parameters of a six-degree-of-freedom parallel manipulator that can be used as a haptic device. The objective function is composed of a desired spherical shape translation workspace and a desired orientation workspace located on the boundaries of the desired translation workspace, along with a global conditioning index based on a homogeneous Jacobian matrix. The objective function was optimized to satisfy the desired orientation workspace at the boundary positions as translated from a neutral position of the increased entropy mechanism. An optimization result with desired translation and orientation workspaces for a haptic device was obtained to show the effectiveness of the suggested scheme, and the kinematic performances of the proposed model were compared with those of a preexisting base model

Optimum design of 6-DOF parallel manipulator with translational/rotational workspaces for haptic device application

International Nuclear Information System (INIS)

Yoon, Jung Won; Hwang, Yoon Kwon; Ryu, Je Ha

2010-01-01

This paper proposes an optimum design method that satisfies the desired orientation workspace at the boundary of the translation workspace while maximizing the mechanism isotropy for parallel manipulators. A simple genetic algorithm is used to obtain the optimal linkage parameters of a six-degree-of-freedom parallel manipulator that can be used as a haptic device. The objective function is composed of a desired spherical shape translation workspace and a desired orientation workspace located on the boundaries of the desired translation workspace, along with a global conditioning index based on a homogeneous Jacobian matrix. The objective function was optimized to satisfy the desired orientation workspace at the boundary positions as translated from a neutral position of the increased entropy mechanism. An optimization result with desired translation and orientation workspaces for a haptic device was obtained to show the effectiveness of the suggested scheme, and the kinematic performances of the proposed model were compared with those of a preexisting base model

Errors and mistakes in the traditional optimum design of experiments on exponential absorption

International Nuclear Information System (INIS)

Burge, E.J.

1977-01-01

The treatment of statistical errors in absorption experiments using particle counters, given by Rose and Shapiro (1948), is shown to be incorrect for non-zero background counts. For the simplest case of only one absorber thickness, revised conditions are computed for the optimum geometry and the best apportionment of counting times for the incident and transmitted beams for a wide range of relative backgrounds (0, 10 -5 -10 2 ). The two geometries of Rose and Shapiro are treated, (I) beam area fixed, absorber thickness varied, and (II) beam area and absorber thickness both varied, but with effective volume of absorber constant. For case (I) the new calculated errors in the absorption coefficients are shown to be about 0.7 of the Rose and Shapiro values for the largest background, and for case (II) about 0.4. The corresponding fractional times for background counts are (I) 0.7 and (II) 0.07 of those given by Rose and Shapiro. For small backgrounds the differences are negligible. Revised values are also computed for the sensitivity of the accuracy to deviations from optimum transmission. (Auth.)

Performance and optimum design of convective-radiative rectangular fin with convective base heating, wall conduction resistance, and contact resistance between the wall and the fin base

International Nuclear Information System (INIS)

Aziz, Abdul; Beers-Green, Arlen B.

2009-01-01

This paper investigates the performance and optimum design of a longitudinal rectangular fin attached to a convectively heated wall of finite thickness. The exposed surfaces of the fin lose heat to the environmental sink by simultaneous convection and radiation. The tip of the fin is assumed to lose heat by convection and radiation to the same sink. The analysis and optimization of the fin is conducted numerically using the symbolic algebra package Maple. The temperature distribution, the heat transfer rates, and the fin efficiency data is presented illustrating how the thermal performance of the fin is affected by the convection-conduction number, the radiation-conduction number, the base convection Biot number, the convection and radiation Biot numbers at the tip, and the dimensionless sink temperature. Charts are presented showing the relationship between the optimum convection-conduction number and the optimum radiation-conduction number for different values of the base convection Biot number and dimensionless sink temperature and fixed values of the convection and radiation Biot numbers at the tip. Unlike the few other papers which have applied the Adomian's decomposition and the differential quadrature element method to this problem but give illustrative results for specific fin geometry and thermal variables, the present graphical data are generally applicable and can be used by fin designers without delving into the mathematical details of the computational techniques.

CT4 - Cost-Optimum Procedures

DEFF Research Database (Denmark)

Thomsen, Kirsten Engelund; Wittchen, Kim Bjarne

This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings.......This report collects the status in European member states regarding implementation of the cos optimum procedure for setting energy performance requirements to new and existing buildings....

The optimum lead thickness for lead-activation detectors

International Nuclear Information System (INIS)

Si Fenni; Hu Qingyuan

2009-01-01

The optimum lead thickness for lead-activation detectors has been studied in this paper. First existence of the optimum lead thickness is explained theoretically. Then the optimum lead thickness is obtained by two methods, MCNP5 calculation and mathematical estimation. At last factors which affect the optimum lead thickness are discussed. It turns out that the optimum lead thickness is irrelevant to incident neutron energies. It is recommended 2.5 cm generally.

An integrated computer aided system for integrated design of chemical processes

DEFF Research Database (Denmark)

Gani, Rafiqul; Hytoft, Glen; Jaksland, Cecilia

1997-01-01

In this paper, an Integrated Computer Aided System (ICAS), which is particularly suitable for solving problems related to integrated design of chemical processes; is presented. ICAS features include a model generator (generation of problem specific models including model simplification and model ...... form the basis for the toolboxes. The available features of ICAS are highlighted through a case study involving the separation of binary azeotropic mixtures. (C) 1997 Elsevier Science Ltd....

Computer-aided design of control systems to meet many requirements

Science.gov (United States)

Schy, A. A.; Adams, W. M., Jr.; Johnson, K. G.

1974-01-01

A method is described for using nonlinear programing in the computer-aided design of airplane control systems. It is assumed that the quality of such systems depends on many criteria. These criteria are included in the constraints vector (instead of attempting to combine them into a single scalar criterion, as is usually done), and the design proceeds through a sequence of nonlinear programing solutions in which the designer varies the specification of sets of requirements levels. The method is applied to design of a lateral stability augmentation system (SAS) for a fighter airplane, in which the requirements vector is chosen from the official handling qualities specifications. Results are shown for several simple SAS configurations designed to obtain desirable handling qualities over all design flight conditions with minimum feedback gains. The choice of the final design for each case is not unique but depends on the designer's decision as to which achievable set of requirements levels represents the best for that system. Results indicate that it may be possible to design constant parameter SAS which can satisfy the most stringent handling qualities requirements for fighter airplanes in all flight conditions. The role of the designer as a decision maker, interacting with the computer program, is discussed. Advantages of this type of designer-computer interaction are emphasized. Desirable extensions of the method are indicated.

Model-based computer-aided design for controlled release of pesticides

DEFF Research Database (Denmark)

Muro Sunè, Nuria; Gani, Rafiqul; Bell, G.

2005-01-01

In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available, ...... extended models have been developed and implemented into a computer-aided system. The total model consisting of the property models embedded into the release models are then employed to study the release of different combinations of AIs and polymer-based microcapsules.......In the field of controlled release technology for pesticides or active ingredients (AI), models that can predict its delivery during application are important for purposes of design and marketing of the pesticide product. Appropriate models for the controlled release of pesticides, if available...

Integrated computer-aided design in automotive development development processes, geometric fundamentals, methods of CAD, knowledge-based engineering data management

CERN Document Server

Mario, Hirz; Gfrerrer, Anton; Lang, Johann

2013-01-01

The automotive industry faces constant pressure to reduce development costs and time while still increasing vehicle quality. To meet this challenge, engineers and researchers in both science and industry are developing effective strategies and flexible tools by enhancing and further integrating powerful, computer-aided design technology. This book provides a valuable overview of the development tools and methods of today and tomorrow. It is targeted not only towards professional project and design engineers, but also to students and to anyone who is interested in state-of-the-art computer-aided development. The book begins with an overview of automotive development processes and the principles of virtual product development. Focusing on computer-aided design, a comprehensive outline of the fundamentals of geometry representation provides a deeper insight into the mathematical techniques used to describe and model geometrical elements. The book then explores the link between the demands of integrated design pr...

Automated a complex computer aided design concept generated using macros programming

Science.gov (United States)

Rizal Ramly, Mohammad; Asrokin, Azharrudin; Abd Rahman, Safura; Zulkifly, Nurul Ain Md

2013-12-01

Changing a complex Computer Aided design profile such as car and aircraft surfaces has always been difficult and challenging. The capability of CAD software such as AutoCAD and CATIA show that a simple configuration of a CAD design can be easily modified without hassle, but it is not the case with complex design configuration. Design changes help users to test and explore various configurations of the design concept before the production of a model. The purpose of this study is to look into macros programming as parametric method of the commercial aircraft design. Macros programming is a method where the configurations of the design are done by recording a script of commands, editing the data value and adding a certain new command line to create an element of parametric design. The steps and the procedure to create a macro programming are discussed, besides looking into some difficulties during the process of creation and advantage of its usage. Generally, the advantages of macros programming as a method of parametric design are; allowing flexibility for design exploration, increasing the usability of the design solution, allowing proper contained by the model while restricting others and real time feedback changes.

Automated a complex computer aided design concept generated using macros programming

International Nuclear Information System (INIS)

Ramly, Mohammad Rizal; Asrokin, Azharrudin; Rahman, Safura Abd; Zulkifly, Nurul Ain Md

2013-01-01

Changing a complex Computer Aided design profile such as car and aircraft surfaces has always been difficult and challenging. The capability of CAD software such as AutoCAD and CATIA show that a simple configuration of a CAD design can be easily modified without hassle, but it is not the case with complex design configuration. Design changes help users to test and explore various configurations of the design concept before the production of a model. The purpose of this study is to look into macros programming as parametric method of the commercial aircraft design. Macros programming is a method where the configurations of the design are done by recording a script of commands, editing the data value and adding a certain new command line to create an element of parametric design. The steps and the procedure to create a macro programming are discussed, besides looking into some difficulties during the process of creation and advantage of its usage. Generally, the advantages of macros programming as a method of parametric design are; allowing flexibility for design exploration, increasing the usability of the design solution, allowing proper contained by the model while restricting others and real time feedback changes

Design of an Yb-169 source optimized for gold nanoparticle-aided radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Reynoso, Francisco J.; Manohar, Nivedh [Nuclear/Radiological Engineering and Medical Physics Programs, Woodruff School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332-0405 (United States); Krishnan, Sunil [Department of Radiation Oncology, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States); Cho, Sang Hyun, E-mail: scho@mdanderson.org [Department of Radiation Physics and Department of Imaging Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas 77030 (United States)

2014-10-15

Purpose: To find an optimum design of a new high-dose rate ytterbium (Yb)-169 brachytherapy source that would maximize the dose enhancement during gold nanoparticle-aided radiation therapy (GNRT), while meeting practical constraints for manufacturing a clinically relevant brachytherapy source. Methods: Four different Yb-169 source designs were considered in this investigation. The first three source models had a single encapsulation made of one of the following materials: aluminum, titanium, and stainless steel. The last source model adopted a dual encapsulation design with an inner aluminum capsule surrounding the Yb-core and an outer titanium capsule. Monte Carlo (MC) simulations using the Monte Carlo N-Particle code version 5 (MCNP5) were conducted initially to investigate the spectral changes caused by these four source designs and the associated variations in macroscopic dose enhancement across the tumor loaded with gold nanoparticles (GNPs) at 0.7% by weight. Subsequent MC simulations were performed using the EGSnrc and NOREC codes to determine the secondary electron spectra and microscopic dose enhancement as a result of irradiating the GNP-loaded tumor with the MCNP-calculated source spectra. Results: Effects of the source filter design were apparent in the current MC results. The intensity-weighted average energy of the Yb-169 source varied from 108.9 to 122.9 keV, as the source encapsulation material changed from aluminum to stainless steel. Accordingly, the macroscopic dose enhancement calculated at 1 cm away from the source changed from 51.0% to 45.3%. The sources encapsulated by titanium and aluminum/titanium combination showed similar levels of dose enhancement, 49.3% at 1 cm, and average energies of 113.0 and 112.3 keV, respectively. While the secondary electron spectra due to the investigated source designs appeared to look similar in general, some differences were noted especially in the low energy region (<50 keV) of the spectra suggesting the

Computer-Aided Sustainable Process Synthesis-Design and Analysis

DEFF Research Database (Denmark)

Kumar Tula, Anjan

-groups is that, the performance of the entire process can be evaluated from the contributions of the individual process-groups towards the selected flowsheet property (for example, energy consumed). The developed flowsheet property models include energy consumption, carbon footprint, product recovery, product......Process synthesis involves the investigation of chemical reactions needed to produce the desired product, selection of the separation techniques needed for downstream processing, as well as taking decisions on sequencing the involved separation operations. For an effective, efficient and flexible...... focuses on the development and application of a computer-aided framework for sustainable synthesis-design and analysis of process flowsheets by generating feasible alternatives covering the entire search space and includes analysis tools for sustainability, LCA and economics. The synthesis method is based...

Custom-Made Computer-Aided-Design/Computer-Aided-Manufacturing Biphasic Calcium-Phosphate Scaffold for Augmentation of an Atrophic Mandibular Anterior Ridge

Directory of Open Access Journals (Sweden)

Francesco Guido Mangano

2015-01-01

Full Text Available This report documents the clinical, radiographic, and histologic outcome of a custom-made computer-aided-design/computer-aided-manufactured (CAD/CAM scaffold used for the alveolar ridge augmentation of a severely atrophic anterior mandible. Computed tomographic (CT images of an atrophic anterior mandible were acquired and modified into a 3-dimensional (3D reconstruction model; this was transferred to a CAD program, where a custom-made scaffold was designed. CAM software generated a set of tool-paths for the manufacture of the scaffold on a computer-numerical-control milling machine into the exact shape of the 3D design. A custom-made scaffold was milled from a synthetic micromacroporous biphasic calcium phosphate (BCP block. The scaffold closely matched the shape of the defect: this helped to reduce the time for the surgery and contributed to good healing. One year later, newly formed and well-integrated bone was clinically available, and two implants (AnyRidge, MegaGen, Gyeongbuk, South Korea were placed. The histologic samples retrieved from the implant sites revealed compact mature bone undergoing remodelling, marrow spaces, and newly formed trabecular bone surrounded by residual BCP particles. This study demonstrates that custom-made scaffolds can be fabricated by combining CT scans and CAD/CAM techniques. Further studies on a larger sample of patients are needed to confirm these results.

What is the effect of optimum independent parameters on solar heating systems?

International Nuclear Information System (INIS)

Kaçan, Erkan; Ulgen, Koray; Kaçan, Erdal

2015-01-01

Highlights: • The efficiency effect of 4 independent parameters over the solar heating system are examined. • 3 of 4 independent parameters are found as decisive parameter for system design. • Maximum exergetic efficiency exceeded 11% at optimized process. • Maximum environmental efficiency reached up to 95% at optimized process. • The optimum outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses. - Abstract: Researchers are rather closely involved in Solar Combisystems recently, but there is lack of study that presents the optimum design parameters. Therefore, in this study the influence of the four major variables, namely; outside, inside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector on the energetic, exergetic and environmental efficiencies of Solar Combisystems are investigated and system optimization is done by a combination of response surface methodology. Measured parameters and energetic–exergetic and environmental performance curves are found and statistical model is created parallel with the actual data. It is found that statistical model is significant and all “lack-of-fit” values are non-significant. Thus, it is proved that statistical model strongly represents the design model. Outside temperature, solar radiation on horizontal surface and instantaneous efficiency of solar collector are the decisive parameters for all responses but instantaneous efficiency of solar collector is not for environmental efficiency. Maximum exergetic efficiency exceeded 11%, maximum environmental efficiency reached up to 95% at optimized process. The optimum value of the outside temperature and solar radiation are found as 22 °C and 773 W/m"2 for all responses, on the other hand optimum collector efficiency is found around 60% for energetic and exergetic efficiency values. Inside temperature is not a decisive parameter for all responses.

Computer-aided drug design at Boehringer Ingelheim

Science.gov (United States)

Muegge, Ingo; Bergner, Andreas; Kriegl, Jan M.

2017-03-01

Computer-Aided Drug Design (CADD) is an integral part of the drug discovery endeavor at Boehringer Ingelheim (BI). CADD contributes to the evaluation of new therapeutic concepts, identifies small molecule starting points for drug discovery, and develops strategies for optimizing hit and lead compounds. The CADD scientists at BI benefit from the global use and development of both software platforms and computational services. A number of computational techniques developed in-house have significantly changed the way early drug discovery is carried out at BI. In particular, virtual screening in vast chemical spaces, which can be accessed by combinatorial chemistry, has added a new option for the identification of hits in many projects. Recently, a new framework has been implemented allowing fast, interactive predictions of relevant on and off target endpoints and other optimization parameters. In addition to the introduction of this new framework at BI, CADD has been focusing on the enablement of medicinal chemists to independently perform an increasing amount of molecular modeling and design work. This is made possible through the deployment of MOE as a global modeling platform, allowing computational and medicinal chemists to freely share ideas and modeling results. Furthermore, a central communication layer called the computational chemistry framework provides broad access to predictive models and other computational services.

Determination of Optimum Condition of Leucine Content in Beef Protein Hydrolysate using Response Surface Methodology

International Nuclear Information System (INIS)

Siti Roha Ab Mutalib; Zainal Samicho; Noriham Abdullah

2016-01-01

The aim of this study is to determine the optimum condition of leucine content in beef hydrolysate. Beef hydrolysate was prepared by enzymatic hydrolysis using bromelain enzyme produced from pineapple peel. Parameter conditions such as concentration of bromelain, hydrolysis temperature and hydrolysis time were assessed to obtain the optimum leucine content of beef hydrolysate according to experimental design which was recommended by response surface methodology (RSM). Leucine content in beef hydrolysate was determined using AccQ. Tag amino acid analysis method using high performance liquid chromatography (HPLC). The condition of optimum leucine content was at bromelain concentration of 1.38 %, hydrolysis temperature of 42.5 degree Celcius and hydrolysis time of 31.59 hours with the predicted leucine content of 26.57 %. The optimum condition was verified with the leucine value obtained was 26.25 %. Since there was no significant difference (p>0.05) between the predicted and verified leucine values, thus it indicates that the predicted optimum condition by RSM can be accepted to predict the optimum leucine content in beef hydrolysate. (author)

Optimum Design of High Speed Prop-Rotors

Science.gov (United States)

Chattopadhyay, Aditi

1992-01-01

The objective of this research is to develop optimization procedures to provide design trends in high speed prop-rotors. The necessary disciplinary couplings are all considered within a closed loop optimization process. The procedures involve the consideration of blade aeroelastic, aerodynamic performance, structural and dynamic design requirements. Further, since the design involves consideration of several different objectives, multiobjective function formulation techniques are developed.

A numerical study on an optimum design of a Cross-flow type Power Turbine (CPT)

International Nuclear Information System (INIS)

Ha, Jin Ho; Kim, Chul Ho

2008-01-01

A wind turbine is one of the most popular energy conversion systems to generate electricity from the natural renewable energy source and an axial-flow type wind turbine is commonly used system for the generation electricity in the wind farm nowadays. In this study, a cross-flow type turbine has been studied for the application of wind turbine for electricity generation. The target capacity of the electric power generation of the model wind turbine developing in this project is 12volts-150A/H(about 1.8Kw). The important design parameters of the model turbine impeller are the inlet and exit angle of the turbine blade, number of blade, hub/tip ratio and exit flow angle of the housing. In this study, the radial equilibrium theorem was used to decide the inlet and exit angle of the model impeller blade and CFD technique was incorporated to have performance analysis of the design model power turbine for the optimum design of the geometry of the Cross-flow Power Turbine impeller and Casing. In CFD, Navier-Stokes equation is solved with the SIMPLEC method in a general coordinates system. Realizable k-ε turbulent model with MARS scheme was used for evaluating torque of each blade in the Cross-flow Power Turbine (CPT). From the result, the designed CPT with 24 impeller blades at α=40 .deg. and β=85 .deg. of turbine blade angle was estimated to generate 1.2Nm of the indicated torque and 200watts of the indicated power. On the basis of the rules of similarity, the generating power capacity of the real size CPT that is eight times longer than the model impeller is predicted to have an 1.6kW of the output power (about 12V-130A/H or 24V-65A/H)

Computer-Aided Design of Microstrip GaAs Mesfet Amplifiers

DEFF Research Database (Denmark)

Nielsen, Niels Ole

1976-01-01

Results on computer-aided design of broadband GaAs MESFET amplifiers in microstrip is presented. The analysis of an amplifier is based on measured scattering parameters and a model of the microstrip structure, which includes parasitics and junction effects. The optimized performance of one stage...... amplifiers with lossless distributed matching elements is presented. Realized amplifiers are in good agreement with the theory. One stage amplifiers with a 1 ¿m FET in chip form exhibit 5.8 dB of gain in the range 8-12 GHz, while a gain of 4.5 dB from 4-8 GHz has been obtained with a packaged 1 ¿m FET....

Optimum design of dual pressure heat recovery steam generator using non-dimensional parameters based on thermodynamic and thermoeconomic approaches

International Nuclear Information System (INIS)

Naemi, Sanaz; Saffar-Avval, Majid; Behboodi Kalhori, Sahand; Mansoori, Zohreh

2013-01-01

The thermodynamic and thermoeconomic analyses are investigated to achieve the optimum operating parameters of a dual pressure heat recovery steam generator (HRSG), coupled with a heavy duty gas turbine. In this regard, the thermodynamic objective function including the exergy waste and the exergy destruction, is defined in such a way to find the optimum pinch point, and consequently to minimize the objective function by using non-dimensional operating parameters. The results indicated that, the optimum pinch point from thermodynamic viewpoint is 2.5 °C and 2.1 °C for HRSGs with live steam at 75 bar and 90 bar respectively. Since thermodynamic analysis is not able to consider economic factors, another objective function including annualized installation cost and annual cost of irreversibilities is proposed. To find the irreversibility cost, electricity price and also fuel price are considered independently. The optimum pinch point from thermoeconomic viewpoint on basis of electricity price is 20.6 °C (75 bar) and 19.2 °C (90 bar), whereas according to the fuel price it is 25.4 °C and 23.7 °C. Finally, an extensive sensitivity analysis is performed to compare optimum pinch point for different electricity and fuel prices. -- Highlights: ► Presenting thermodynamic and thermoeconomic optimization of a heat recovery steam generator. ► Defining an objective function consists of exergy waste and exergy destruction. ► Defining an objective function including capital cost and cost of irreversibilities. ► Obtaining the optimized operating parameters of a dual pressure heat recovery boiler. ► Computing the optimum pinch point using non-dimensional operating parameters

Using eye tracking technology to compare the effectiveness of malignant hyperthermia cognitive aid design.

Science.gov (United States)

King, Roderick; Hanhan, Jaber; Harrison, T Kyle; Kou, Alex; Howard, Steven K; Borg, Lindsay K; Shum, Cynthia; Udani, Ankeet D; Mariano, Edward R

2018-05-15

Malignant hyperthermia is a rare but potentially fatal complication of anesthesia, and several different cognitive aids designed to facilitate a timely and accurate response to this crisis currently exist. Eye tracking technology can measure voluntary and involuntary eye movements, gaze fixation within an area of interest, and speed of visual response and has been used to a limited extent in anesthesiology. With eye tracking technology, we compared the accessibility of five malignant hyperthermia cognitive aids by collecting gaze data from twelve volunteer participants. Recordings were reviewed and annotated to measure the time required for participants to locate objects on the cognitive aid to provide an answer; cumulative time to answer was the primary outcome. For the primary outcome, there were differences detected between cumulative time to answer survival curves (P typescript with minimal use of single color blocking.

MVPACK: a computer-aided design tool for multivariable control systems

International Nuclear Information System (INIS)

Mensah, S.; Frketich, G.

1985-10-01

The design and analysis of high-performance controllers for complex plants require a collection of interactive, powerful computer software. MVPACK, an open-ended package for the computer-aided design of control systems, has been developed in the Reactor Control Branch of the Chalk River Nuclear Laboratories. The package is fully interactive and includes a comprehensive state-of-the-art mathematical library to support development of complex, multivariable, control algorithms. Coded in RATFOR, MVPACK is portable with minimal changes. It operates with a flexible data structure which makes efficient use of minicomputer resources and provides a standard framework for program generation. The existence of a help mechanism enhances the simplicity of package utilization. This paper provides a brief tutorial overview of the package. It reviews the specifications used in the design and implementation of the package and briefly describes the database structure, supporting libraries and some design and analysis modules of MVPACK. Several application examples to illustrate the capability of the package are given. Experience with MVPACK shows that the package provides a synergistic environment for the design of control and regulation systems, and that it is a unique tool for training of control system engineers

Design Procedure for High-Speed PM Motors Aided by Optimization Algorithms

Directory of Open Access Journals (Sweden)

Francesco Cupertino

2018-02-01

Full Text Available This paper considers the electromagnetic and structural co-design of superficial permanent magnet synchronous machines for high-speed applications, with the aid of a Pareto optimization procedure. The aim of this work is to present a design procedure for the afore-mentioned machines that relies on the combined used of optimization algorithms and finite element analysis. The proposed approach allows easy analysis of the results and a lowering of the computational burden. The proposed design method is presented through a practical example starting from the specifications of an aeronautical actuator. The design procedure is based on static finite element simulations for electromagnetic analysis and on analytical formulas for structural design. The final results are validated through detailed transient finite element analysis to verify both electromagnetic and structural performance. The step-by-step presentation of the proposed design methodology allows the reader to easily adapt it to different specifications. Finally, a comparison between a distributed-winding (24 slots and a concentrated-winding (6 slots machine is presented demonstrating the advantages of the former winding arrangement for high-speed applications.

Mommy, Daddy--What's AIDS?

Science.gov (United States)

National Association of Pediatric Nurse Associates and Practitioners, Cherry Hill, NJ.

This brochure is designed to help parents answer the questions that their children may ask them about Acquired Immune Deficiency Syndrome (AIDS) and the Human Immuno Deficiency Virus (HIV), the virus that causes AIDS. It provides basic information about AIDS and HIV, as well as sources for further information, such as the National AIDS Hotline. It…

Gracilibacillus aidingensis sp. nov., a novel moderately halophilic bacterium isolated from Aiding salt lake.

Science.gov (United States)

Guan, Tong-Wei; Tian, Lei; Li, En-Yuan; Tang, Shu-Kun; Zhang, Xiao-Ping

2017-11-01

A novel Gram-positive, aerobe, moderately halophilic bacterium was isolated from saline soil of Aiding lake in Xinjiang, north-west of China, designated strain YIM 98001 T . Cells were rod-shaped, motile and grew at 5-20% (w/v) NaCl (optimum 10%), pH 6-10 (optimum pH 7.0) and 4-45 °C (optimum 37 °C). The major cellular fatty acids were anteiso C 15:0 , anteiso C 17:0 , iso C 15:0 . The predominant respiratory quinone was MK-7. Diphosphatidylglycerol, phosphatidylglycerol, phosphoglycolipid were the major polar lipids. Meso-diaminopimelic acid was the diagnostic diamino acid of the cell-wall peptidoglycan. The G+C content was 36.46 mol%. 16S rRNA gene sequence analysis showed that the strain belongs to the family Bacillaceae, with the highest sequence similarity to the type strain Gracilibacillus thailandensis TP2-8 T (96.84%), followed by Gracilibacillus saliphilus YIM 91119 T (96.78%) and Gracilibacillus ureilyticus MF38 T (96.57%), thus confirming the affiliation of strain YIM 98001 T to the genus Gracilibacillus. The polyphasic approach indicates that strain YIM 98001 T represents a novel species of the genus Gracilibacillus, for which the name Gracilibacillus aidingensis is proposed. The type strain is YIM 98001 T (=KCTC 42683 T  = DSMZ 104330 T ).

The computer-aided design of a servo system as a multiple-criteria decision problem

NARCIS (Netherlands)

Udink ten Cate, A.J.

1986-01-01

This paper treats the selection of controller gains of a servo system as a multiple-criteria decision problem. In contrast to the usual optimization-based approaches to computer-aided design, inequality constraints are included in the problem as unconstrained objectives. This considerably simplifies

Computer-aided design in power engineering. Application of software tools

International Nuclear Information System (INIS)

Stojkovic, Zlatan

2012-01-01

Demonstrates the use software tools in the practice of design in the field of power systems. Presents many applications in the design in the field of power systems. Useful for educative purposes and practical work. This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel and Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems is discussed. Here, the emphasis is put on the standard software MS Excel and MS Project.

Computer-aided design in power engineering. Application of software tools

Energy Technology Data Exchange (ETDEWEB)

Stojkovic, Zlatan

2012-07-01

Demonstrates the use software tools in the practice of design in the field of power systems. Presents many applications in the design in the field of power systems. Useful for educative purposes and practical work. This textbooks demonstrates the application of software tools in solving a series of problems from the field of designing power system structures and systems. It contains four chapters: The first chapter leads the reader through all the phases necessary in the procedures of computer aided modeling and simulation. It guides through the complex problems presenting on the basis of eleven original examples. The second chapter presents application of software tools in power system calculations of power systems equipment design. Several design example calculations are carried out using engineering standards like MATLAB, EMTP/ATP, Excel and Access, AutoCAD and Simulink. The third chapters focuses on the graphical documentation using a collection of software tools (AutoCAD, EPLAN, SIMARIS SIVACON, SIMARIS DESIGN) which enable the complete automation of the development of graphical documentation of a power systems. In the fourth chapter, the application of software tools in the project management in power systems is discussed. Here, the emphasis is put on the standard software MS Excel and MS Project.

Optimum bolus wizard settings in insulin pumps in children with Type 1 diabetes

DEFF Research Database (Denmark)

Andersen, A J B; Ostenfeld, A; Pipper, C B

2016-01-01

: Optimum insulin pump settings at pump initiation depend on both insulin requirements and use of the pump. Settings need to be individualized because the standardized calculation factors are not constant for children. There is a need to develop specific age- and insulin dose-dependent calculation factors.......AIM: To evaluate current insulin pump settings in an optimally regulated paediatric population using bolus wizard. METHODS: We used a retrospective study design to analyse data from 124 children on insulin pump therapy who had optimum HbA1c levels [

Generic Mathematical Programming Formulation and Solution for Computer-Aided Molecular Design

DEFF Research Database (Denmark)

Zhang, Lei; Cignitti, Stefano; Gani, Rafiqul

2015-01-01

This short communication presents a generic mathematical programming formulation for Computer-Aided Molecular Design (CAMD). A given CAMD problem, based on target properties, is formulated as a Mixed Integer Linear/Non-Linear Program (MILP/MINLP). The mathematical programming model presented here......, which is formulated as an MILP/MINLP problem, considers first-order and second-order molecular groups for molecular structure representation and property estimation. It is shown that various CAMD problems can be formulated and solved through this model....

Actuation and system design and evaluation OMS engine shutoff valve, Volume 1. [space shuttles

Science.gov (United States)

Dunn, V. B.

1975-01-01

A technology program was conducted to identify and verify the optimum valve and actuation system concept for the Space Shuttle Orbit Maneuvering System engine. Of major importance to the valve and actuation system selection was the ten-year, 100-mission, 10,000-cycle life requirement, while maintaining high reliability, low leakage, and low weight. Valve and actuation system concepts were comparatively evaluated against past valve failure reports and potential failure modes due to the shuttle mission profile to aid in the selection of the most optimum concept for design, manufacture and verification testing. Two valve concepts were considered during the preliminary design stage; i.e., the moving seat and lifting ball. Two actuation systems were manufactured and tested. Test results demonstrate the viability of a lifting ball concept as well as the applicability of an ac motor actuation system to best meet the requirements of the shuttle mission.

Attitude of medical students towards the use of audio visual aids during didactic lectures in pharmacology in a medical college of central India

OpenAIRE

Mehul Agrawal; Rajanish Kumar Sankdia

2016-01-01

Background: Students favour teaching methods employing audio visual aids over didactic lectures not using these aids. However, the optimum use of audio visual aids is essential for deriving their benefits. During a lecture, both the visual and auditory senses are used to absorb information. Different methods of lecture are and ndash; chalk and board, power point presentations (PPT) and mix of aids. This study was done to know the students' preference regarding the various audio visual aids, ...

Advanced computer-aided design for bone tissue-engineering scaffolds.

Science.gov (United States)

Ramin, E; Harris, R A

2009-04-01

The design of scaffolds with an intricate and controlled internal structure represents a challenge for tissue engineering. Several scaffold-manufacturing techniques allow the creation of complex architectures but with little or no control over the main features of the channel network such as the size, shape, and interconnectivity of each individual channel, resulting in intricate but random structures. The combined use of computer-aided design (CAD) systems and layer-manufacturing techniques allows a high degree of control over these parameters with few limitations in terms of achievable complexity. However, the design of complex and intricate networks of channels required in CAD is extremely time-consuming since manually modelling hundreds of different geometrical elements, all with different parameters, may require several days to design individual scaffold structures. An automated design methodology is proposed by this research to overcome these limitations. This approach involves the investigation of novel software algorithms, which are able to interact with a conventional CAD program and permit the automated design of several geometrical elements, each with a different size and shape. In this work, the variability of the parameters required to define each geometry has been set as random, but any other distribution could have been adopted. This methodology has been used to design five cubic scaffolds with interconnected pore channels that range from 200 to 800 microm in diameter, each with an increased complexity of the internal geometrical arrangement. A clinical case study, consisting of an integration of one of these geometries with a craniofacial implant, is then presented.

A conceptual framework for designing micro electrical connectors for hearing aid instruments

OpenAIRE

Doagou Rad, Saeed; Islam, Aminul; Fuglsang-Philip, M.

2016-01-01

Electrical connectors play vital roles in modern electronic instruments. Hearing aid devices as advanced combinations of micro mechanics and electronics comprise various electrical connectors for different purposes. However, the current trend in the miniaturization along with the sharp technological advancements have urged them to incorporate increased number of electrical contacts. The current paper presents a conceptual framework for designing and manufacturing novel plug and socket systems...

An analysis of the optimum operating point for a switched reluctance motor

International Nuclear Information System (INIS)

Mao, S.-H.; Tsai, M.-C.

2004-01-01

This paper proposes a simple method to determine the optimum exciting current, for high output torque in switched reluctance motors (SRMs). By modelling the flux-linkage with one curve at the unaligned position, and with two curves at the aligned position, the maximum increment of the co-energy and torque can be predicted accurately, and the optimum exciting current can also be determined. This easily implemented method is aimed at providing an index for determining the SRM exciting current. This will be useful for SRM designers in deciding the rated current and in obtaining the maximum motor efficiency

Evaluation of marginal/internal fit of chrome-cobalt crowns: Direct laser metal sintering versus computer-aided design and computer-aided manufacturing.

Science.gov (United States)

Gunsoy, S; Ulusoy, M

2016-01-01

The purpose of this study was to evaluate the internal and marginal fit of chrome cobalt (Co-Cr) crowns were fabricated with laser sintering, computer-aided design (CAD) and computer-aided manufacturing, and conventional methods. Polyamide master and working models were designed and fabricated. The models were initially designed with a software application for three-dimensional (3D) CAD (Maya, Autodesk Inc.). All models were fabricated models were produced by a 3D printer (EOSINT P380 SLS, EOS). 128 1-unit Co-Cr fixed dental prostheses were fabricated with four different techniques: Conventional lost wax method, milled wax with lost-wax method (MWLW), direct laser metal sintering (DLMS), and milled Co-Cr (MCo-Cr). The cement film thickness of the marginal and internal gaps was measured by an observer using a stereomicroscope after taking digital photos in ×24. Best fit rates according to mean and standard deviations of all measurements was in DLMS both in premolar (65.84) and molar (58.38) models in μm. A significant difference was found DLMS and the rest of fabrication techniques (P 0.05). DMLS was best fitting fabrication techniques for single crown based on the results.The best fit was found in marginal; the larger gap was found in occlusal.All groups were within the clinically acceptable misfit range.

Therapist-Aided Exposure for Women with Lifelong Vaginismus: A Replicated Single-Case Design

Science.gov (United States)

ter Kuile, Moniek M.; Bulte, Isis; Weijenborg, Philomeen T. M.; Beekman, Aart; Melles, Reinhilde; Onghena, Patrick

2009-01-01

Vaginismus is commonly described as a persistent difficulty in allowing vaginal entry of a penis or other object. Lifelong vaginismus occurs when a woman has never been able to have intercourse. A replicated single-case A-B-phase design was used to investigate the effectiveness of therapist-aided exposure for lifelong vaginismus. A baseline period…

Technology and Jobs: Computer-Aided Design. Numerical-Control Machine-Tool Operators. Office Automation.

Science.gov (United States)

Stanton, Michael; And Others

1985-01-01

Three reports on the effects of high technology on the nature of work include (1) Stanton on applications and implications of computer-aided design for engineers, drafters, and architects; (2) Nardone on the outlook and training of numerical-control machine tool operators; and (3) Austin and Drake on the future of clerical occupations in automated…

Micrometric precision of prosthetic dental crowns obtained by optical scanning and computer-aided designing/computer-aided manufacturing system

Science.gov (United States)

das Neves, Flávio Domingues; de Almeida Prado Naves Carneiro, Thiago; do Prado, Célio Jesus; Prudente, Marcel Santana; Zancopé, Karla; Davi, Letícia Resende; Mendonça, Gustavo; Soares, Carlos José

2014-08-01

The current study evaluated prosthetic dental crowns obtained by optical scanning and a computer-aided designing/computer-aided manufacturing system using micro-computed tomography to compare the marginal fit. The virtual models were obtained with four different scanning surfaces: typodont (T), regular impressions (RI), master casts (MC), and powdered master casts (PMC). Five virtual models were obtained for each group. For each model, a crown was designed on the software and milled from feldspathic ceramic blocks. Micro-CT images were obtained for marginal gap measurements and the data were statistically analyzed by one-way analysis of variance followed by Tukey's test. The mean vertical misfit was T=62.6±65.2 μm; MC=60.4±38.4 μm; PMC=58.1±38.0 μm, and RI=89.8±62.8 μm. Considering a percentage of vertical marginal gap of up to 75 μm, the results were T=71.5%, RI=49.2%, MC=69.6%, and PMC=71.2%. The percentages of horizontal overextension were T=8.5%, RI=0%, MC=0.8%, and PMC=3.8%. Based on the results, virtual model acquisition by scanning the typodont (simulated mouth) or MC, with or without powder, showed acceptable values for the marginal gap. The higher result of marginal gap of the RI group suggests that it is preferable to scan this directly from the mouth or from MC.

Off-design thermodynamic performances on typical days of a 330 MW solar aided coal-fired power plant in China

International Nuclear Information System (INIS)

Peng, Shuo; Hong, Hui; Wang, Yanjuan; Wang, Zhaoguo; Jin, Hongguang

2014-01-01

Highlights: • Optical loss and heat loss of solar field under different turbine load were investigated. • Off-design thermodynamic feature was disclosed by analyzing several operational parameters. • Possible schemes was proposed to improve the net solar-to-electricity efficiency. - Abstract: The contribution of mid-temperature solar thermal power to improve the performance of coal-fired power plant is analyzed in the present paper. In the solar aided coal-fired power plant, solar heat at <300 °C is used to replace the extracted steam from the steam turbine to heat the feed water. In this way, the steam that was to be extracted could consequently expand in the steam turbine to boost output power. The advantages of a solar aided coal-fired power plant in design condition have been discussed by several researchers. However, thermodynamic performances on off-design operation have not been well discussed until now. In this paper, a typical 330 MW coal-fired power plant in Sinkiang Province of China is selected as the case study to demonstrate the advantages of the solar aided coal-fired power plant under off-design conditions. Hourly thermodynamic performances are analyzed on typical days under partial load. The effects of several operational parameters, such as solar irradiation intensity, incident angle, flow rate of thermal oil, on the performance of solar field efficiency and net solar-to-electricity efficiency were examined. Possible schemes have been proposed for improving the solar aided coal-fired power plant on off-design operation. The results obtained in the current study could provide a promising approach to solve the poor thermodynamic performance of solar thermal power plant and also offer a basis for the practical operation of MW-scale solar aided coal-fired power plant

Prosthetic rehabilitation with an implant-supported fixed prosthesis using computer-aided design and computer-aided manufacturing dental technology for a patient with a mandibulectomy: A clinical report.

Science.gov (United States)

Yoon, Hyung-In; Han, Jung-Suk

2016-02-01

The fabrication of dental prostheses with computer-aided design and computer-aided manufacturing shows acceptable marginal fits and favorable treatment outcomes. This clinical report describes the management of a patient who had undergone a mandibulectomy and received an implant-supported fixed prosthesis by using additive manufacturing for the framework and subtractive manufacturing for the monolithic zirconia restorations. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

A portable anaerobic microbioreactor reveals optimum growth conditions for the methanogen Methanosaeta concilii.

Science.gov (United States)

Steinhaus, Benjamin; Garcia, Marcelo L; Shen, Amy Q; Angenent, Largus T

2007-03-01

Conventional studies of the optimum growth conditions for methanogens (methane-producing, obligate anaerobic archaea) are typically conducted with serum bottles or bioreactors. The use of microfluidics to culture methanogens allows direct microscopic observations of the time-integrated response of growth. Here, we developed a microbioreactor (microBR) with approximately 1-microl microchannels to study some optimum growth conditions for the methanogen Methanosaeta concilii. The microBR is contained in an anaerobic chamber specifically designed to place it directly onto an inverted light microscope stage while maintaining a N2-CO2 environment. The methanogen was cultured for months inside microchannels of different widths. Channel width was manipulated to create various fluid velocities, allowing the direct study of the behavior and responses of M. concilii to various shear stresses and revealing an optimum shear level of approximately 20 to 35 microPa. Gradients in a single microchannel were then used to find an optimum pH level of 7.6 and an optimum total NH4-N concentration of less than 1,100 mg/liter (<47 mg/liter as free NH3-N) for M. concilii under conditions of the previously determined ideal shear stress and pH and at a temperature of 35 degrees C.

Specific features of organizng the computer-aided design of radio-electronic equipment for electrophysical facilities

International Nuclear Information System (INIS)

Mozin, I.V.; Vasil'ev, M.P.

1985-01-01

Problems of developing systems for computer-aided design (CAD) of radioelectronic equipment for large electrophysical facilities such as charged particle accelerators of new generation are discussed. The PLATA subsystem representing a part of CAD and used for printed circuit design is described. The subsystem PLATA is utilized to design, on the average, up to 150 types of circuits a year, 100-120 of which belong to circuits of increased complexity. In this case labour productivity of a designer at documentation increases almost two times

An overview of interactive computer graphics and its application to computer-aided engineering and design

International Nuclear Information System (INIS)

Van Dam, A.

1983-01-01

The purpose of this brief birds-eye view of interactive graphics is to list the key ideas, and to show how one of the most important application areas, Computer Aided Engineering/Design takes advantage of it. (orig.)

Optimum design of A fluidic micro-oscillator

International Nuclear Information System (INIS)

Noh, Yoojeong; Youn, Sungkie; Kim, Moonuhn

2002-01-01

A fluidic micro-oscillator is used to control a linear tool as generating an oscillating fluid jet at its two output ports. The linear tool is a linear actuator that transforms the fluidic energy into mechanical energy via a double acting piston placed in linear actuator housing. Together the two devices form a dynamic microsystem that can be used in medical application. In this paper, we intend to optimize the geometry of the fluidic micro-oscillator. A basic oscillator design is varied in terms of supply nozzle geometry, length of the feedback channels, wall angle, control port width and etc. It was found that characteristics parameters such as frequency, volume flow and output pressure depends strongly on above mentioned design parameters. According to above the observations, we can determine an object function and design variables. Since we eventually have to maximize force to drive and steer a cutting tool, the output pressure difference is chosen as an object function and nozzle width, feedback channel, control port width, distance between splitter and nozzle can be chosen as the design variables. As a result of such design optimization, we can obtain the maximum force. At this time we maximize the output pressure difference using shape optimization

Exact Optimum Design of Segmented Thermoelectric Generators

Directory of Open Access Journals (Sweden)

M. Zare

2016-01-01

Full Text Available A considerable difference between experimental and theoretical results has been observed in the studies of segmented thermoelectric generators (STEGs. Because of simplicity, the approximate methods are widely used for design and optimization of the STEGs. This study is focused on employment of exact method for design and optimization of STEGs and comparison of exact and approximate results. Thus, using new highly efficient thermoelectric materials, four STEGs are proposed to operate in the temperature range of 300 to 1300 kelvins. The proposed STEGs are optimally designed to achieve maximum efficiency. Design and performance characteristics of the optimized generators including maximum conversion efficiency and length of elements are calculated through both exact and approximate methods. The comparison indicates that the approximate method can cause a difference up to 20% in calculation of some design characteristics despite its appropriate results in efficiency calculation. The results also show that the maximum theoretical efficiency of 23.08% is achievable using the new proposed STEGs. Compatibility factor of the selected materials for the proposed STEGs is also calculated using both exact and approximate methods. The comparison indicates a negligible difference in calculation of compatibility factor, despite the considerable difference in calculation of reduced efficiency (temperature independence efficiency.

Efficient Use of Preisach Hysteresis Model in Computer Aided Design

Directory of Open Access Journals (Sweden)

IONITA, V.

2013-05-01

Full Text Available The paper presents a practical detailed analysis regarding the use of the classical Preisach hysteresis model, covering all the steps, from measuring the necessary data for the model identification to the implementation in a software code for Computer Aided Design (CAD in Electrical Engineering. An efficient numerical method is proposed and the hysteresis modeling accuracy is tested on magnetic recording materials. The procedure includes the correction of the experimental data, which are used for the hysteresis model identification, taking into account the demagnetizing effect for the sample that is measured in an open-circuit device (a vibrating sample magnetometer.

Analytical Design Package (ADP2): A computer aided engineering tool for aircraft transparency design

Science.gov (United States)

Wuerer, J. E.; Gran, M.; Held, T. W.

1994-01-01

The Analytical Design Package (ADP2) is being developed as a part of the Air Force Frameless Transparency Program (FTP). ADP2 is an integrated design tool consisting of existing analysis codes and Computer Aided Engineering (CAE) software. The objective of the ADP2 is to develop and confirm an integrated design methodology for frameless transparencies, related aircraft interfaces, and their corresponding tooling. The application of this methodology will generate high confidence for achieving a qualified part prior to mold fabrication. ADP2 is a customized integration of analysis codes, CAE software, and material databases. The primary CAE integration tool for the ADP2 is P3/PATRAN, a commercial-off-the-shelf (COTS) software tool. The open architecture of P3/PATRAN allows customized installations with different applications modules for specific site requirements. Integration of material databases allows the engineer to select a material, and those material properties are automatically called into the relevant analysis code. The ADP2 materials database will be composed of four independent schemas: CAE Design, Processing, Testing, and Logistics Support. The design of ADP2 places major emphasis on the seamless integration of CAE and analysis modules with a single intuitive graphical interface. This tool is being designed to serve and be used by an entire project team, i.e., analysts, designers, materials experts, and managers. The final version of the software will be delivered to the Air Force in Jan. 1994. The Analytical Design Package (ADP2) will then be ready for transfer to industry. The package will be capable of a wide range of design and manufacturing applications.

Optimum Tilt Angle at Tropical Region

Directory of Open Access Journals (Sweden)

S Soulayman

2015-02-01

Full Text Available : One of the important parameters that affect the performance of a solar collector is its tilt angle with the horizon. This is because of the variation of tilt angle changes the amount of solar radiation reaching the collector surface. Meanwhile, is the rule of thumb, which says that solar collector Equator facing position is the best, is valid for tropical region? Thus, it is required to determine the optimum tilt as for Equator facing and for Pole oriented collectors. In addition, the question that may arise: how many times is reasonable for adjusting collector tilt angle for a definite value of surface azimuth angle? A mathematical model was used for estimating the solar radiation on a tilted surface, and to determine the optimum tilt angle and orientation (surface azimuth angle for the solar collector at any latitude. This model was applied for determining optimum tilt angle and orientation in the tropical zones, on a daily basis, as well as for a specific period. The optimum angle was computed by searching for the values for which the radiation on the collector surface is a maximum for a particular day or a specific period. The results reveal that changing the tilt angle 12 times in a year (i.e. using the monthly optimum tilt angle maintains approximately the total amount of solar radiation near the maximum value that is found by changing the tilt angle daily to its optimum value. This achieves a yearly gain in solar radiation of 11% to 18% more than the case of a solar collector fixed on a horizontal surface.

Basic Principles of Industrial Electric Power Network Computer Aided Design and Engineering

Directory of Open Access Journals (Sweden)

M. I. Fursanov

2012-01-01

Full Text Available A conceptual model for a computer aided design and engineering system has been developed in the paper. The paper presents basic automation process principles including a graphical representation   network and calculation results, convenient user interface, automatic mode calculation, selection of transformer rated power and cross-section area of wires. The developed algorithm and program make it possible to save time and improve quality of project implementation.

OPTIMUM HEAT STORAGE DESIGN FOR SDHW SYSTEMS

DEFF Research Database (Denmark)

Shah, Louise Jivan; Furbo, Simon

1997-01-01

Two simulation models have been used to analyse the heat storage design’s influence on the thermal performance of solar domestic hot water (SDHW) systems. One model is especially designed for traditional SDHW systems based on a heat storage design where the solar heat exchanger is a built-in spiral....... The other model is especially designed for low flow SDHW systems based on a mantle tank.The tank design’s influence on the thermal performance of the SDHW systems has been investigated in a way where only one tank parameter has been changed at a time in the calculations. In this way a direct analysis...

Design of tailor-made chemical blend using a decomposition-based computer-aided approach

DEFF Research Database (Denmark)

Yunus, Nor Alafiza; Gernaey, Krist; Manan, Z.A.

2011-01-01

Computer aided techniques form an efficient approach to solve chemical product design problems such as the design of blended liquid products (chemical blending). In chemical blending, one tries to find the best candidate, which satisfies the product targets defined in terms of desired product...... methodology for blended liquid products that identifies a set of feasible chemical blends. The blend design problem is formulated as a Mixed Integer Nonlinear Programming (MINLP) model where the objective is to find the optimal blended gasoline or diesel product subject to types of chemicals...... and their compositions and a set of desired target properties of the blended product as design constraints. This blend design problem is solved using a decomposition approach, which eliminates infeasible and/or redundant candidates gradually through a hierarchy of (property) model based constraints. This decomposition...

Psychological first-aid: a practical aide-memoire.

Science.gov (United States)

Leach, J

1995-07-01

Despite advances made in recent years in medical first aid, psychiatric intervention, survival training and equipment design, many people still perish quickly during and immediately following a disastrous event. In this study, individuals and groups of survivors of life-threatening events were debriefed and the behavior of those who coped well during such a threat to life were compared with those who did not. The behaviors of those who coped well were distilled into a set of principles for psychological first aid; that is, a series of simple actions for use within a disaster which serves to recover victims to functional behavior as quickly as possible, thus increasing their chance for survival. These principles of psychological first aid have recently been introduced into basic first aid and survival training courses for both military and civilian units.

Design of slurry bubble column reactors: novel technique for optimum catalyst size selection contractual origin of the invention

Science.gov (United States)

Gamwo, Isaac K [Murrysville, PA; Gidaspow, Dimitri [Northbrook, IL; Jung, Jonghwun [Naperville, IL

2009-11-17

A method for determining optimum catalyst particle size for a gas-solid, liquid-solid, or gas-liquid-solid fluidized bed reactor such as a slurry bubble column reactor (SBCR) for converting synthesis gas into liquid fuels considers the complete granular temperature balance based on the kinetic theory of granular flow, the effect of a volumetric mass transfer coefficient between the liquid and the gas, and the water gas shift reaction. The granular temperature of the catalyst particles representing the kinetic energy of the catalyst particles is measured and the volumetric mass transfer coefficient between the gas and liquid phases is calculated using the granular temperature. Catalyst particle size is varied from 20 .mu.m to 120 .mu.m and a maximum mass transfer coefficient corresponding to optimum liquid hydrocarbon fuel production is determined. Optimum catalyst particle size for maximum methanol production in a SBCR was determined to be in the range of 60-70 .mu.m.

Development of computer-aided design and production system for nuclear power plant

International Nuclear Information System (INIS)

Ishii, Masanori

1983-01-01

The technically required matters related to the design and production of nuclear power stations tended to increase from the viewpoint of the safety and reliability, and it is indispensable to cope with such technically required matters skillfully for the rationalization of the design and production and for the construction of highly reliable plants. Ishikawajima Harima Heavy Industries Co., Ltd., has developed the computer-aided design data information and engineering system which performs dialogue type design and drawing, and as the result, the design-production consistent system is developed to do stress analysis, production design, production management and the output of data for numerically controlled machine tools consistently. In this paper, mainly the consistent system in the field of plant design centering around piping and also the computer system for the design of vessels and others are outlined. The features of the design works for nuclear power plants, the rationalization of the design and production management of piping and vessels, and the application of the CAD system to other general equipment and improvement works are reported. This system is the powerful means to meet the requirement of heightening quality and reducing cost. (Kako, I.)

Development of a multimedia educational programme for first-time hearing aid users: a participatory design.

Science.gov (United States)

Ferguson, Melanie; Leighton, Paul; Brandreth, Marian; Wharrad, Heather

2018-05-02

To develop content for a series of interactive video tutorials (or reusable learning objects, RLOs) for first-time adult hearing aid users, to enhance knowledge of hearing aids and communication. RLO content was based on an electronically-delivered Delphi review, workshops, and iterative peer-review and feedback using a mixed-methods participatory approach. An expert panel of 33 hearing healthcare professionals, and workshops involving 32 hearing aid users and 11 audiologists. This ensured that social, emotional and practical experiences of the end-user alongside clinical validity were captured. Content for evidence-based, self-contained RLOs based on pedagogical principles was developed for delivery via DVD for television, PC or internet. Content was developed based on Delphi review statements about essential information that reached consensus (≥90%), visual representations of relevant concepts relating to hearing aids and communication, and iterative peer-review and feedback of content. This participatory approach recognises and involves key stakeholders in the design process to create content for a user-friendly multimedia educational intervention, to supplement the clinical management of first-time hearing aid users. We propose participatory methodologies are used in the development of content for e-learning interventions in hearing-related research and clinical practice.

Study on the optimum design of bus window pillar join40t; Bus window pillar ketsugo buzai no saiteki sekkei ni kansuru kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tomioka, N [Nihon University, Tokyo (Japan); Lim, S; Kim, M; Lee, H; Kang, S; Bae, D

1997-10-01

Automobile body structure is generally assembled using various spot welded box sectional members. Especially, in the case of the bus, the shape of window pillar joint is assembled m T-type. This T-type member has some problem such as high stress concentration, low fatigue strength and structural rigidity. Therefore, in this report, performed a study on the optimum design of the bus window pillar joint for such problem by FEM analysis and experiments. 1 ref., 10 figs., 2 tabs.

Breaking the Glass Ceiling: Increasing the Meaningful Involvement of Women Living With HIV/AIDS (MIWA) in the Design and Delivery of HIV/AIDS Services.

Science.gov (United States)

Carter, Allison; Greene, Saara; Nicholson, Valerie; O'Brien, Nadia; Sanchez, Margarite; de Pokomandy, Alexandra; Loutfy, Mona; Kaida, Angela

2015-01-01

The meaningful involvement of women living with HIV/AIDS (MIWA) is a key feature of women-centred HIV care, yet little is known about transforming MIWA from principle to practice. Drawing on focus group data from the Canadian HIV Women's Sexual and Reproductive Health Cohort Study (CHIWOS), we explored HIV-positive women's meaningful involvement in the design and delivery of HIV/AIDS services in British Columbia, Canada. In this article, we highlight the benefits and tensions that emerge as women traverse multiple roles as service users and service providers within their care communities, and the impact this has on their access to care and overall health.

Evolution of facility layout requirements and CAD [computer-aided design] system development

International Nuclear Information System (INIS)

Jones, M.

1990-06-01

The overall configuration of the Superconducting Super Collider (SSC) including the infrastructure and land boundary requirements were developed using a computer-aided design (CAD) system. The evolution of the facility layout requirements and the use of the CAD system are discussed. The emphasis has been on minimizing the amount of input required and maximizing the speed by which the output may be obtained. The computer system used to store the data is also described

Music and hearing aids.

Science.gov (United States)

Madsen, Sara M K; Moore, Brian C J

2014-10-31

The signal processing and fitting methods used for hearing aids have mainly been designed to optimize the intelligibility of speech. Little attention has been paid to the effectiveness of hearing aids for listening to music. Perhaps as a consequence, many hearing-aid users complain that they are not satisfied with their hearing aids when listening to music. This issue inspired the Internet-based survey presented here. The survey was designed to identify the nature and prevalence of problems associated with listening to live and reproduced music with hearing aids. Responses from 523 hearing-aid users to 21 multiple-choice questions are presented and analyzed, and the relationships between responses to questions regarding music and questions concerned with information about the respondents, their hearing aids, and their hearing loss are described. Large proportions of the respondents reported that they found their hearing aids to be helpful for listening to both live and reproduced music, although less so for the former. The survey also identified problems such as distortion, acoustic feedback, insufficient or excessive gain, unbalanced frequency response, and reduced tone quality. The results indicate that the enjoyment of listening to music with hearing aids could be improved by an increase of the input and output dynamic range, extension of the low-frequency response, and improvement of feedback cancellation and automatic gain control systems. © The Author(s) 2014.

Music and Hearing Aids

Directory of Open Access Journals (Sweden)

Sara M. K. Madsen

2014-10-01

Full Text Available The signal processing and fitting methods used for hearing aids have mainly been designed to optimize the intelligibility of speech. Little attention has been paid to the effectiveness of hearing aids for listening to music. Perhaps as a consequence, many hearing-aid users complain that they are not satisfied with their hearing aids when listening to music. This issue inspired the Internet-based survey presented here. The survey was designed to identify the nature and prevalence of problems associated with listening to live and reproduced music with hearing aids. Responses from 523 hearing-aid users to 21 multiple-choice questions are presented and analyzed, and the relationships between responses to questions regarding music and questions concerned with information about the respondents, their hearing aids, and their hearing loss are described. Large proportions of the respondents reported that they found their hearing aids to be helpful for listening to both live and reproduced music, although less so for the former. The survey also identified problems such as distortion, acoustic feedback, insufficient or excessive gain, unbalanced frequency response, and reduced tone quality. The results indicate that the enjoyment of listening to music with hearing aids could be improved by an increase of the input and output dynamic range, extension of the low-frequency response, and improvement of feedback cancellation and automatic gain control systems.

Computer Aided Design of the Link-Fork Head-Piston Assembly of the Kaplan Turbine with Solidworks

Directory of Open Access Journals (Sweden)

Camelia Jianu

2010-10-01

Full Text Available The paper presents the steps for 3D computer aided design (CAD of the link-fork head-piston assembly of the Kaplan turbine made in SolidWorks.The present paper is a tutorial for a Kaplan turbine assembly 3D geometry, which is dedicated to the Assembly design and Drawing Geometry and Drawing Annotation.

Improving the Design of Capacitive Micromachined Ultrasonic Transducers Aided with Sensitivity Analysis

Directory of Open Access Journals (Sweden)

A Martowicz

2016-09-01

Full Text Available The paper presents the results of analysis performed to search for feasible design improvements for capacitive micromachined ultrasonic transducer. Carried out search has been aided with the sensitivity analysis and the application of Response Surface Method. The multiphysics approach has been taken into account in elaborated finite element model of one cell of described transducer in order to include significant physical phenomena present in modelled microdevice. The set of twelve input uncertain and design parameters consists of geometric, material and control properties. The amplitude of dynamic membrane deformation of the transducer has been chosen as studied parameter. The objective of performed study has been defined as the task of finding robust design configurations of the transducer, i.e. characterizing maximal value of deformation amplitude with its minimal variation.

Artificial neural networks aided conceptual stage design of water harvesting structures

Directory of Open Access Journals (Sweden)

Vinay Chandwani

2016-09-01

Full Text Available The paper presents artificial neural networks (ANNs based methodology for ascertaining the structural parameters of water harvesting structures (WHS at the conceptual stage of design. The ANN is trained using exemplar patterns generated using an in-house MSExcel based design program, to draw a functional relationship between the five inputs design parameters namely, peak flood discharge, safe bearing capacity of strata, length of structure, height of structure and silt factor and four outputs namely, top width, bottom width, foundation depth and flood lift representing the structural parameters of WHS. The results of the study show that, the structural parameters of the WHS predicted using ANN model are in close agreement with the actual field parameters. The versatility of ANN to map complex or complex unknown relationships has been proven in the study. A parametric sensitivity study is also performed to assess the most significant design parameter. The study holistically presents a neural network based decision support tool that can be used to accurately estimate the major design parameters of the WHS at the conceptual stage of design in quick time, aiding the engineer-in-charge to conveniently forecast the budget requirements and minimize the labor involved during the subsequent phases of analysis and design.

CADDS [Computer-aided Drafting and Design System] brings quality and precision to the Canadian Maple [research reactor

International Nuclear Information System (INIS)

Goland, D.

1989-01-01

Atomic Energy of Canada Ltd (AECL) has found that using the ''intelligent'' Computer-Aided Drafting and Design System (CADDS) helped address design problems at an early stage and led to productivity gains of around 50 per cent. Other bonuses were the quality and precision of the designs and documents produced. Its application to the MAPLE research reactor project is described. (author)

Model-based Computer Aided Framework for Design of Process Monitoring and Analysis Systems

DEFF Research Database (Denmark)

Singh, Ravendra; Gernaey, Krist; Gani, Rafiqul

2009-01-01

In the manufacturing industry, for example, the pharmaceutical industry, a thorough understanding of the process is necessary in addition to a properly designed monitoring and analysis system (PAT system) to consistently obtain the desired end-product properties. A model-based computer....... The knowledge base provides the necessary information/data during the design of the PAT system while the model library generates additional or missing data needed for design and analysis. Optimization of the PAT system design is achieved in terms of product data analysis time and/or cost of monitoring equipment......-aided framework including the methods and tools through which the design of monitoring and analysis systems for product quality control can be generated, analyzed and/or validated, has been developed. Two important supporting tools developed as part of the framework are a knowledge base and a model library...

Curves and surfaces for computer-aided geometric design a practical guide

CERN Document Server

Farin, Gerald

1992-01-01

A leading expert in CAGD, Gerald Farin covers the representation, manipulation, and evaluation of geometric shapes in this the Third Edition of Curves and Surfaces for Computer Aided Geometric Design. The book offers an introduction to the field that emphasizes Bernstein-Bezier methods and presents subjects in an informal, readable style, making this an ideal text for an introductory course at the advanced undergraduate or graduate level.The Third Edition includes a new chapter on Topology, offers new exercises and sections within most chapters, combines the material on Geometric Continuity i

Study Guide for First Aid Practices.

Science.gov (United States)

Thygerson, Alton L.

This study guide is designed to accompany the American National Red Cross texts ADVANCED FIRST AID AND EMERGENCY CARE and STANDARD FIRST AID AND PERSONAL SAFETY. Part one serves as an introduction to first aid. The legal aspects of first aid are discussed along with a list of suggested first aid kit contents, and information on first aid books is…

Optimum Design Parameters of Box Window DSF Office at Different Glazing Types under Sub Interval of Intermediate Sky Conditions (20-40 klux)

Science.gov (United States)

Elayeb, O. K.; Alghoul, M. A.; Sopian, K.; Khrita, N. G.

2017-11-01

Despite Double skin façade (DSF) buildings are widely deployed worldwide, daylighting strategy is not commonly incorporated in these buildings compare to other strategies. Therefore, further theoretical and experimental studies would lead to adopting daylighting strategy in DSF office buildings. The aim of this study is to investigate the daylighting performance of office building at different design parameters of box window DSF using different glazing types under sub interval of intermediate sky conditions (20-40) klux using the (IES VE) simulation tool from Integrated Environmental Solutions - Virtual Environment. The implemented design parameters are window wall ratio (WWR) of internal façade (10-100) %, cavity depth (CD) of DSF (1-2.5) m and different glazing types. The glazing types were selected from the list available in the (IES VE) simulation tool. After series of evaluations, bronze tinted coating (STOPSOL) is implemented for the exterior façade while clear float, clear reflective coating (STOPSOL), grey and brown tinted coating (Anti-sun float) and blue coating tinted (SUNCOOL float) are implemented for the interior façade. In this paper, several evaluation parameters are used to quantify the optimum design parameters that would balance the daylighting requirements of a box window DSF office versus sky conditions range (20-40) klux. The optimum design parameters of DSF office building obtained under different glazing types are highlighted as follows. When using bronze tinted coating (STOPSOL) for the exterior façade, the glazing types of interior façade that showed superior daylighting performance of DSF office at (CD of 1.0m with WWR of 70%), (CD of 1.5m with WWR of 70%), (CD of 2.0m with WWR of 70%) and (CD of 2.0m with WWR of 70%) are grey tinted coating (Anti-sun float), clear reflective coating (STOPSOL), brown tinted coating (Anti-sun float), and clear float glazing respectively. Blue Coating tinted (SUNCOOL float) of interior façade glazing

New computational and experimental stress analysis method for the design decision on optimum piston configuration. Piston oryoku no computer simulation to shinshikenho ni yoru keijo saitekika

Energy Technology Data Exchange (ETDEWEB)

Anno, N; Sugita, J [Honda R and D, Co. Ltd., Saitama (Japan)

1993-03-01

Piston troubles are mostly caused by cracks generating in each part of a piston. The finite element method (FEM) has been used for stress analysis of the piston, but has not been applied enough to design optimum configurations due to too much time for making models. In this study, stress analysis was carried out by the boundary element method (BEM), with which it is easy to make models and to change configurations, with various improvements. In addition, methods to execute a thermal load fatigue test and an actual running test to confirm analytical results were also improved. BEASY was used as basic software for analysis by BEM, and some improvements such as reduction of CPU time and optimization of memory using methods were carried out. It was easy to change configurations of the models by BEM, and the effect of the change in the piston boss configuration upon the stress agreed well with the actual test result. Design and evaluation of the optimum configuration has become easier by feedback of the results of the newly developed thermal load fatigue test to the analysis by BEM. 5 refs., 12 figs., 2 tabs.

Detail design of empennage of an unmanned aerial vehicle

Science.gov (United States)

Sarker, Md. Samad; Panday, Shoyon; Rasel, Md; Salam, Md. Abdus; Faisal, Kh. Md.; Farabi, Tanzimul Hasan

2017-12-01

In order to maintain the operational continuity of air defense systems, unmanned autonomous or remotely controlled unmanned aerial vehicle (UAV) plays a great role as a target for the anti-aircraft weapons. The aerial vehicle must comply with the requirements of high speed, remotely controlled tracking and navigational aids, operational sustainability and sufficient loiter time. It can also be used for aerial reconnaissance, ground surveillance and other intelligence operations. This paper aims to develop a complete tail design of an unmanned aerial vehicle using Systems Engineering approach. The design fulfils the requirements of longitudinal and directional trim, stability and control provided by the horizontal and vertical tail. Tail control surfaces are designed to provide sufficient control of the aircraft in critical conditions. Design parameters obtained from wing design are utilized in the tail design process as required. Through chronological calculations and successive iterations, optimum values of 26 tail design parameters are determined.

Design of an adaptive CubeSat transmitter for achieving optimum signal-to-noise ratio (SNR)

Science.gov (United States)

Jaswar, F. D.; Rahman, T. A.; Hindia, M. N.; Ahmad, Y. A.

2017-12-01

CubeSat technology has opened the opportunity to conduct space-related researches at a relatively low cost. Typical approach to maintain an affordable cubeSat mission is to use a simple communication system, which is based on UHF link with fixed-transmit power and data rate. However, CubeSat in the Low Earth Orbit (LEO) does not have relative motion with the earth rotation, resulting in variable propagation path length that affects the transmission signal. A transmitter with adaptive capability to select multiple sets of data rate and radio frequency (RF) transmit power is proposed to improve and optimise the link. This paper presents the adaptive UHF transmitter design as a solution to overcome the variability of the propagation path. The transmitter output power is adjustable from 0.5W to 2W according to the mode of operations and satellite power limitations. The transmitter is designed to have four selectable modes to achieve the optimum signal-to-noise ratio (SNR) and efficient power consumption based on the link budget analysis and satellite requirement. Three prototypes are developed and tested for space-environment conditions such as the radiation test. The Total Ionizing Dose measurements are conducted in the radiation test done at Malaysia Nuclear Agency Laboratory. The results from this test have proven that the adaptive transmitter can perform its operation with estimated more than seven months in orbit. This radiation test using gamma source with 1.5krad exposure is the first one conducted for a satellite program in Malaysia.

Sequence homolog-based molecular engineering for shifting the enzymatic pH optimum

Directory of Open Access Journals (Sweden)

Fuqiang Ma

2016-09-01

Full Text Available Cell-free synthetic biology system organizes multiple enzymes (parts from different sources to implement unnatural catalytic functions. Highly adaption between the catalytic parts is crucial for building up efficient artificial biosynthetic systems. Protein engineering is a powerful technology to tailor various enzymatic properties including catalytic efficiency, substrate specificity, temperature adaptation and even achieve new catalytic functions. However, altering enzymatic pH optimum still remains a challenging task. In this study, we proposed a novel sequence homolog-based protein engineering strategy for shifting the enzymatic pH optimum based on statistical analyses of sequence-function relationship data of enzyme family. By two statistical procedures, artificial neural networks (ANNs and least absolute shrinkage and selection operator (Lasso, five amino acids in GH11 xylanase family were identified to be related to the evolution of enzymatic pH optimum. Site-directed mutagenesis of a thermophilic xylanase from Caldicellulosiruptor bescii revealed that four out of five mutations could alter the enzymatic pH optima toward acidic condition without compromising the catalytic activity and thermostability. Combination of the positive mutants resulted in the best mutant M31 that decreased its pH optimum for 1.5 units and showed increased catalytic activity at pH < 5.0 compared to the wild-type enzyme. Structure analysis revealed that all the mutations are distant from the active center, which may be difficult to be identified by conventional rational design strategy. Interestingly, the four mutation sites are clustered at a certain region of the enzyme, suggesting a potential “hot zone” for regulating the pH optima of xylanases. This study provides an efficient method of modulating enzymatic pH optima based on statistical sequence analyses, which can facilitate the design and optimization of suitable catalytic parts for the construction

Designing an Engaging and Informative Application About First Aid

DEFF Research Database (Denmark)

Foldager, Nicolai; Hansen, Hans; Tewes, Mikkel Skovsmose

2016-01-01

This study aimed at developing an engaging and informative application within first aid and CPR for people who are already certified in first aid. The paper outlines discussions within definitions of serious games, humor, gamification and engagement. Further we suggest specific elements...

Simulation-aided design and fabrication of nanoprobes for scanning probe microscopy

International Nuclear Information System (INIS)

Liu, Bernard Haochih; Chang, Day-Bin

2011-01-01

We proposed and demonstrated a flexible and effective method to design and fabricate scanning probes for atomic force microscopy applications. Computer simulations were adopted to evaluate design specifications and desired performance of atomic force microscope (AFM) probes; the fabrication processes were guided by feedback from simulation results. Through design-simulation-fabrication iterations, tipless cantilevers and tapping mode probes were successfully made with errors as low as 2% in designed resonant frequencies. For tapping mode probes, the probe tip apex achieved a 10 nm radius of curvature without additional sharpening steps; tilt-compensated probes were also fabricated for better scanning performance. This method provides AFM users improved probe quality and practical guidelines for customized probes, which can support the development of novel scanning probe microscopy (SPM) applications. -- Research highlights: → We developed a design-simulation-fabrication strategy for customized AFM/SPM probes and demonstrated the results of tipless cantilever, sharpened probe tip, and tilt-compensated probe. → This simulation-aided method improved the geometry control and performance prediction of AFM probes; the error in resonant frequency was reduced to ∼2%. → Integration of simulation in design and fabrication of AFM probes expedites development of new probes and consequently promotes novel SPM applications.

Optimum gain and phase for stochastic cooling systems

International Nuclear Information System (INIS)

Meer, S. van der.

1984-01-01

A detailed analysis of optimum gain and phase adjustment in stochastic cooling systems reveals that the result is strongly influenced by the beam feedback effect and that for optimum performance the system phase should change appreciably across each Schottky band. It is shown that the performance is not greatly diminished if a constant phase is adopted instead. On the other hand, the effect of mixing between pick-up and kicker (which produces a phase change similar to the optimum one) is shown to be less perturbing than is usually assumed, provided that the absolute value of the gain is not too far from the optimum value. (orig.)

History and evolution of the pharmacophore concept in computer-aided drug design.

Science.gov (United States)

Güner, Osman F

2002-12-01

With computer-aided drug design established as an integral part of the lead discovery and optimization process, pharmacophores have become a focal point for conceptualizing and understanding receptor-ligand interactions. In the structure-based design process, pharmacophores can be used to align molecules based on the three-dimensional arrangement of chemical features or to develop predictive models (e.g., 3D-QSAR) that correlate with the experimental activities of a given training set. Pharmacophores can be also used as search queries for retrieving potential leads from structural databases, for designing molecules with specific desired attributes, or as fingerprints for assessing similarity and diversity of molecules. This review article presents a historical perspective on the evolution and use of the pharmacophore concept in the pharmaceutical, biotechnology, and fragrances industry with published examples of how the technology has contributed and advanced the field.

Development and application of computer-aided design methods for cell factory optimization

DEFF Research Database (Denmark)

Cardoso, Joao

Genetically modified organisms (GMOs) can be used to produce chemicals for everyday applications. Engineering microorganisms is a multidisciplinary task comprising four steps: design, build, test and learn. The design and learn phases rely on computational, statistical models, data analysis...... and machine learning. The process of creating strains with commercially relevant titers is time consuming and expensive. Computer-aided design (CAD) software can help scientists build better strains by providing models and algorithms that can be used to generate and test hypotheses before implementing them...... microbial cell factories. In this PhD thesis we present cameo, a CAD software for metabolic engineering that uses GEMs. State-of-the-art and novel algorithms are implemented in cameo. These algorithms have been made accessible using a high-level API to enable any user to start running them without having...

Crew aiding and automation: A system concept for terminal area operations, and guidelines for automation design

Science.gov (United States)

Dwyer, John P.

1994-01-01

This research and development program comprised two efforts: the development of guidelines for the design of automated systems, with particular emphasis on automation design that takes advantage of contextual information, and the concept-level design of a crew aiding system, the Terminal Area Navigation Decision Aiding Mediator (TANDAM). This concept outlines a system capable of organizing navigation and communication information and assisting the crew in executing the operations required in descent and approach. In service of this endeavor, problem definition activities were conducted that identified terminal area navigation and operational familiarization exercises addressing the terminal area navigation problem. Both airborne and ground-based (ATC) elements of aircraft control were extensively researched. The TANDAM system concept was then specified, and the crew interface and associated systems described. Additionally, three descent and approach scenarios were devised in order to illustrate the principal functions of the TANDAM system concept in relation to the crew, the aircraft, and ATC. A plan for the evaluation of the TANDAM system was established. The guidelines were developed based on reviews of relevant literature, and on experience gained in the design effort.

Thermal optimum analyses and mechanical design of 10-kA, vapor-cooled power leads for SSC superconducting magnet tests at MTL

International Nuclear Information System (INIS)

Shu, Q.S.; Demko, J.; Dorman, R.; Finan, D.; Hatfield, D.; Syromyatnikov, I.; Zolotov, A.; Mazur, P.; Peterson, T.

1992-08-01

The spiral-fin, 10-kA, helium vapor-cooled power leads have been designed for Superconducting Super Collider superconducting magnet tests at the Magnet Test Laboratory. In order to thermally optimize the parameters of the power leads, the lead diameters-which minimize the Carnot work for several different lengths, two different fin geometries, and two RRR values of the lead materials-were determined. The cryogenic refrigeration and liquefaction loads for supporting the leads have also been calculated. The optimum operational condition with different currents is discussed. An improved mechanical design of the 10-kA power leads was undertaken, with careful consideration of the cryogenic and mechanical performance. In the design, a new thermal barrier device to reduce heat conduction from the vacuum and gas seal area was employed. Therefore, the electric insulation assembly, which isolates the ground potential parts of the lead from the high-power parts, was moved into a warm region in order to prevent vacuum and helium leakage in the 0-ring seals due to transient cold temperature. The instrumentation for testing the power leads is also discussed

Creating an Electronic Reference and Information Database for Computer-aided ECM Design

Science.gov (United States)

Nekhoroshev, M. V.; Pronichev, N. D.; Smirnov, G. V.

2018-01-01

The paper presents a review on electrochemical shaping. An algorithm has been developed to implement a computer shaping model applicable to pulse electrochemical machining. For that purpose, the characteristics of pulse current occurring in electrochemical machining of aviation materials have been studied. Based on integrating the experimental results and comprehensive electrochemical machining process data modeling, a subsystem for computer-aided design of electrochemical machining for gas turbine engine blades has been developed; the subsystem was implemented in the Teamcenter PLM system.

Computer-aided design for metabolic engineering.

Science.gov (United States)

Fernández-Castané, Alfred; Fehér, Tamás; Carbonell, Pablo; Pauthenier, Cyrille; Faulon, Jean-Loup

2014-12-20

The development and application of biotechnology-based strategies has had a great socio-economical impact and is likely to play a crucial role in the foundation of more sustainable and efficient industrial processes. Within biotechnology, metabolic engineering aims at the directed improvement of cellular properties, often with the goal of synthesizing a target chemical compound. The use of computer-aided design (CAD) tools, along with the continuously emerging advanced genetic engineering techniques have allowed metabolic engineering to broaden and streamline the process of heterologous compound-production. In this work, we review the CAD tools available for metabolic engineering with an emphasis, on retrosynthesis methodologies. Recent advances in genetic engineering strategies for pathway implementation and optimization are also reviewed as well as a range of bionalytical tools to validate in silico predictions. A case study applying retrosynthesis is presented as an experimental verification of the output from Retropath, the first complete automated computational pipeline applicable to metabolic engineering. Applying this CAD pipeline, together with genetic reassembly and optimization of culture conditions led to improved production of the plant flavonoid pinocembrin. Coupling CAD tools with advanced genetic engineering strategies and bioprocess optimization is crucial for enhanced product yields and will be of great value for the development of non-natural products through sustainable biotechnological processes. Copyright © 2014 Elsevier B.V. All rights reserved.

A Novel Computer-Aided Design/Computer-Assisted Manufacture Method for One-Piece Removable Partial Denture and Evaluation of Fit.

Science.gov (United States)

Ye, Hongqiang; Li, Xinxin; Wang, Guanbo; Kang, Jing; Liu, Yushu; Sun, Yuchun; Zhou, Yongsheng

2018-02-15

To investigate a computer-aided design/computer-aided manufacturing (CAD/CAM) process for producing one-piece removable partial dentures (RPDs) and to evaluate their fits in vitro. A total of 15 one-piece RPDs were designed using dental CAD and reverse engineering software and then fabricated with polyetheretherketone (PEEK) using CAM. The gaps between RPDs and casts were measured and compared with traditional cast framework RPDs. Gaps were lower for one-piece PEEK RPDs compared to traditional RPDs. One-piece RPDs can be manufactured by CAD/CAM, and their fits were better than those of traditional RPDs.

Growing of the mathematical thinking imaginative to students in designing of the teaching aids for CWD towards to joyful learning

Science.gov (United States)

Sugiman; Sugiharti, E.; Kurniawati, N. F.

2018-03-01

Government and the private parties had also organized of Special School (SS) and Inclusive School. SS requires of math teachers who were professional in the material, but also master the needs of Children with Disabilities (CwD) in teaching-learning process. The problem: How to design the Teaching Aids for CwD through Extra-Curriculum Training (ECT) activities to Joyful Learning? The purposes of this research: (1) To find new ways how to grow the imaginative in mathematical thinking for students of Mathematics Education. (2) To find a Teaching Aids Design that suitable for CwD who studying in SS. (3) In order to create a Teaching Aids for CwD through activities based on ECT to Joyful Learning. The research method was done by qualitative approach. The research subjects were 6 students of Mathematics Education Study Program of FMIPA UNNES who were interested in attending of the training activities based on ECT. The results: (1) ECT can be a place to grow an Imaginative in Mathematical Thinking of students, (2) created the design of the teaching aids for CwD through activities based on ECT to Joyful Learning as a mirror of the imaginative growth in mathematical thinking for students.

Improving boiler unit performance using an optimum robust minimum-order observer

International Nuclear Information System (INIS)

Moradi, Hamed; Bakhtiari-Nejad, Firooz

2011-01-01

Research highlights: → Multivariable model of a boiler unit with uncertainty. → Design of a robust minimum-order observer. → Developing an optimal functional code in MATLAB environment. → Finding optimum region of observer-based controller poles. → Guarantee of robust performance in the presence of parametric uncertainties. - Abstract: To achieve a good performance of the utility boiler, dynamic variables such as drum pressure, steam temperature and water level of drum must be controlled. In this paper, a linear time invariant (LTI) model of a boiler system is considered in which the input variables are feed-water and fuel mass rates. Due to the inaccessibility of some state variables of boiler system, a minimum-order observer is designed based on Luenberger's model to gain an estimate state x-tilde of the true state x. Low cost of design and high accuracy of states estimation are the main advantages of the minimum-order observer; in comparison with previous designed full-order observers. By applying the observer on the closed-loop system, a regulator system is designed. Using an optimal functional code developed in MATLAB environment, desired observer poles are found such that suitable time response specifications of the boiler system are achieved and the gain and phase margin values are adjusted in an acceptable range. However, the real dynamic model may associate with parametric uncertainties. In that case, optimum region of poles of observer-based controller are found such that the robust performance of the boiler system against model uncertainties is guaranteed.

Costs incurred by applying computer-aided design/computer-aided manufacturing techniques for the reconstruction of maxillofacial defects.

Science.gov (United States)

Rustemeyer, Jan; Melenberg, Alex; Sari-Rieger, Aynur

2014-12-01

This study aims to evaluate the additional costs incurred by using a computer-aided design/computer-aided manufacturing (CAD/CAM) technique for reconstructing maxillofacial defects by analyzing typical cases. The medical charts of 11 consecutive patients who were subjected to the CAD/CAM technique were considered, and invoices from the companies providing the CAD/CAM devices were reviewed for every case. The number of devices used was significantly correlated with cost (r = 0.880; p costs were found between cases in which prebent reconstruction plates were used (€3346.00 ± €29.00) and cases in which they were not (€2534.22 ± €264.48; p costs of two, three and four devices, even when ignoring the cost of reconstruction plates. Additional fees provided by statutory health insurance covered a mean of 171.5% ± 25.6% of the cost of the CAD/CAM devices. Since the additional fees provide financial compensation, we believe that the CAD/CAM technique is suited for wide application and not restricted to complex cases. Where additional fees/funds are not available, the CAD/CAM technique might be unprofitable, so the decision whether or not to use it remains a case-to-case decision with respect to cost versus benefit. Copyright © 2014 European Association for Cranio-Maxillo-Facial Surgery. Published by Elsevier Ltd. All rights reserved.

Optimum Control for Nonlinear Dynamic Radial Deformation of Turbine Casing with Time-Varying LSSVM

Directory of Open Access Journals (Sweden)

Cheng-Wei Fei

2015-01-01

Full Text Available With the development of the high performance and high reliability of aeroengine, the blade-tip radial running clearance (BTRRC of high pressure turbine seriously influences the reliability and performance of aeroengine, wherein the radial deformation control of turbine casing has to be concerned in BTRRC design. To improve BTRRC design, the optimum control-based probabilistic optimization of turbine casing radial deformation was implemented using time-varying least square support vector machine (T-LSSVM by considering nonlinear material properties and dynamic thermal load. First the T-LSSVM method was proposed and its mathematical model was established. And then the nonlinear dynamic optimal control model of casing radial deformation was constructed with T-LSSVM. Thirdly, through the numerical experiments, the T-LSSVM method is demonstrated to be a promising approach in reducing additional design samples and improving computational efficiency with acceptable computational precision. Through the optimum control-based probabilistic optimization for nonlinear dynamic radial turbine casing deformation, the optimum radial deformation is 7.865 × 10−4 m with acceptable reliability degree 0.995 6, which is reduced by 7.86 × 10−5 m relative to that before optimization. These results validate the effectiveness and feasibility of the proposed T-LSSVM method, which provides a useful insight into casing radial deformation, BTRRC control, and the development of gas turbine with high performance and high reliability.

Improved Design of Microphone-Array Hearing Aids

National Research Council Canada - National Science Library

Greenberg, Julie

1994-01-01

...). Research on microphone array hearing aids is motivated by the lack of success of single-microphone systems, as well as the documented advantages of binaural hearing and multiple-element sensing systems...

Optimum Stratification of a Skewed Population

OpenAIRE

D.K. Rao; M.G.M. Khan; K.G. Reddy

2014-01-01

The focus of this paper is to develop a technique of solving a combined problem of determining Optimum Strata Boundaries(OSB) and Optimum Sample Size (OSS) of each stratum, when the population understudy isskewed and the study variable has a Pareto frequency distribution. The problem of determining the OSB isformulated as a Mathematical Programming Problem (MPP) which is then solved by dynamic programming technique. A numerical example is presented to illustrate the compu...

Optimum phase shift in the self-oscillating loop for piezoelectric transformer-based power converters

DEFF Research Database (Denmark)

Ekhtiari, Marzieh; Zsurzsan, Tiberiu-Gabriel; Andersen, Michael A. E.

2017-01-01

A new method is implemented in designing of self-oscillating loop for driving piezoelectric transformers. The implemented method is based on combining both analog and digital control systems. Digitally controlled time delay through the self-oscillating loop results in very precise frequency control...... and ensures optimum operation of the piezoelectric transformer in terms of gain and efficiency. Time delay is implemented digitally for the first time through a 16 bit digital-to-analog converter in the self-oscillating loop. The new design of the delay circuit provides 45 ps time resolution, enabling fine......-grained control of phase in the self-oscillating loop. This allows the control loop to dynamically follow frequency changes of the transformer in each resonant cycle. Ultimately, by selecting the optimum phase shift, maximum efficiency under the load and temperature condition is achievable....

A practical multi-objective design approach for optimum exhaust heat recovery from hybrid stand-alone PV-diesel power systems

International Nuclear Information System (INIS)

Yousefi, Moslem; Kim, Joong Hoon; Hooshyar, Danial; Yousefi, Milad; Sahari, Khairul Salleh Mohamed; Ahmad, Rodina Binti

2017-01-01

Highlights: • Heat recovery exchanger is designed based on practical conditions of a hybrid power system. • Off-the-grid electricity system modeling and analysis using micro-grid analysis software HOMER. • NSGA-II is used for the multi-objective design optimization task. • A new local search is proposed to incorporate the engineering knowledge in NSGA-II. • The proposed approach outperforms the existing ones. - Abstract: Integration of solar power and diesel generators (DGs) together with battery storage has proven to be an efficient choice for stand-alone power systems (SAPS). For higher energy efficiency, heat recovery from exhaust gas of the DG can also be employed to supply all or a portion of the thermal energy demand. Although the design of such heat recovery systems (HRSs) has been studied, the effect of solar power integration has not been taken into account. In this paper, a new approach for practical design of these systems based on varying engine loads is presented. Fast and elitist non-dominated sorting genetic algorithm (NSGA-II) equipped with a novel local search was used for the design process, considering conflicting objectives of annual energy recovery and total cost of the system, and six design variables. An integrated power system, designed for a remote SAPS, was used to evaluate the design approach. The optimum power supply system was first designed using the commercial software Hybrid Optimization of Multiple Energy Resources (HOMER), based on power demand and global solar energy in the region. Heat recovery design was based on the outcome of HOMER for DG hourly load, considering different power scenarios. The proposed approach improves the annual heat recovery of the PV/DG/battery system by 4%, PV/battery by 1.7%, and stand-alone DG by 1.8% when compared with a conventional design based on nominal DG load. The results prove that the proposed approach is effective and that load calculations should be taken into account prior to

Investigations on the optimum design of chemical addition system for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Chang, Byong Hoon [Junior College of Inchon, Inchon (Korea, Republic of); Chung, Chang Kyu; Choi, Han Rim; Kim, Eun Kee; Ro, Tae Sun [Korea Power Engineering Company, Inc. Taejon (Korea, Republic of)

1998-12-31

Mixing characteristics of the chemical additives in the chemical injection tank of the chemical and volume control system(CVCS) were investigated for the Yonggwang Nuclear units 5 and 6. Numerical calculations were performed with a low-Reynolds number turbulence model. Studies were also conducted for the injection tank with a disk located at 1/4H, 2/4H, and 3/4H from the inlet in order to see the effect in the enhancement of chemical mixing. Results show that the optimum arrangement is to locate a disk close to the inlet. 10 refs., 4 figs. (Author)

Investigations on the optimum design of chemical addition system for nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Chang, Byong Hoon [Junior College of Inchon, Inchon (Korea, Republic of); Chung, Chang Kyu; Choi, Han Rim; Kim, Eun Kee; Ro, Tae Sun [Korea Power Engineering Company, Inc. Taejon (Korea, Republic of)

1997-12-31

Mixing characteristics of the chemical additives in the chemical injection tank of the chemical and volume control system(CVCS) were investigated for the Yonggwang Nuclear units 5 and 6. Numerical calculations were performed with a low-Reynolds number turbulence model. Studies were also conducted for the injection tank with a disk located at 1/4H, 2/4H, and 3/4H from the inlet in order to see the effect in the enhancement of chemical mixing. Results show that the optimum arrangement is to locate a disk close to the inlet. 10 refs., 4 figs. (Author)

PSAD, a prototype for monitoring and aid to diagnosis of French PWRs; PSAD, un systeme prototype pour la surveillance et l`aide au diagnostic des centrales REP Francaises

Energy Technology Data Exchange (ETDEWEB)

Jousselin, A.; Bourgeois, P. [Electricite de France (EDF), 78 - Chatou (France); Busquet, J.L.; Monnier, B. [Electricite de France (EDF), 75 - Paris (France); Mouhamed, B. [SEMA Group France, 37 - Meylan (France)

1996-03-01

In order to improve safety and availability in its nuclear power plants, EDF has designed a new generation of monitoring systems integrated into a workstation for monitoring and aid to diagnosis (PSAD). These systems perform on-line monitoring of the main power plant components and PSAD stations provide homogenous aids ro diagnosis which enable plant personnel to diagnose the mechanical behavior of plant equipments. The objective of PSAD is to provide them with high-efficiency and user-friendly tools which can considerably free them from routine tasks. PSAD has a flexible architecture, guaranteeing optimum distribution of computing power to make it available where it is needed, thus enhancing the quality of the information. Its architecture includes diagnosis support software based on artificial intelligence technology which can dialogue with real-time or deferred-time processing software and a relational database. The first version of the prototype is working on a french plant at Tricastin. This version includes the software for the host structure and two monitoring functions: the reactor coolant pumps and the turbo-generator monitoring functions. Internal Structures Monitoring function (ISM) and Loose Parts Detection function (LPD) are under development and should be integrated into PSAD prototype in 1996. (author). 5 refs., 6 figs.

A Computer-Aided FPS-Oriented Approach for Construction Briefing

Institute of Scientific and Technical Information of China (English)

Xiaochun Luo; Qiping Shen

2008-01-01

Function performance specification (FPS) is one of the value management (VM) techniques de- veloped for the explicit statement of optimum product definition. This technique is widely used in software engineering and manufacturing industry, and proved to be successful to perform product defining tasks. This paper describes an FPS-odented approach for construction briefing, which is critical to the successful deliv- ery of construction projects. Three techniques, i.e., function analysis system technique, shared space, and computer-aided toolkit, are incorporated into the proposed approach. A computer-aided toolkit is developed to facilitate the implementation of FPS in the briefing processes. This approach can facilitate systematic, ef- ficient identification, clarification, and representation of client requirements in trail running. The limitations of the approach and future research work are also discussed at the end of the paper.

A computer aided solvent extraction process design in nuclear fuel reprocessing

International Nuclear Information System (INIS)

Britto, S.E.; Purandare, H.D.; Lawande, S.V.

1977-01-01

A rigorous and conceptual design is attempted of the first step of flowsheet formulation for solvent extraction process for fuel reprocessing plant. The design incorporates three cycles of extraction contractors; the first optimised to maximise Pu recovery while the second and third cycles to maximise fission product decontaminations. There are three basic types of extraction steps in these different cycles requiring painstaking design, namely, extraction-scrub, Pu strip-scrub and simple strip. The extraction system to start with is: U nitrate - Pu nitrate - fission product nitrates - nitric acid - tri-butyl phosphate/diluent. With suitable simplifying assumptions and adopting the concept of discrete equilibrium stagewise operation, simple X-Y operating diagrams could be used. The calculations could therefore be done using McCabe Thiele graphical method. The procedure adopted was to consider the macro-component of U to obtain initial optimum flow sheet details and the number of theoretical stages for each contactor and later to incorporate the behaviour of Pu and fission products. A computer program was written to calculate, for different combinations of nitric acid salting strengths, (1) the U concentration profiles along the contractors and (2) the number of stages needed for various different solvent and aqueous phase flow ratios, using experimentally obtained equilibrium data. The method used is indicated and some samples of results obtained for three types of extraction-scrub operation studied are given. These simplified calculations provided the necessary insight into these difficult operations. (auth.)

Experiences in control system design aided by interactive computer programs: temperature control of the laser isotope separation vessel

International Nuclear Information System (INIS)

Gavel, D.T.; Pittenger, L.C.; McDonald, J.S.; Cramer, P.G.; Herget, C.J.

1985-01-01

A robust control system has been designed to regulate temperature in a vacuum vessel. The thermodynamic process is modeled by a set of nonlinear, implicit differential equations. The control design and analysis task exercised many of the computer-aided control systems design software packages, including MATLAB, DELIGHT, and LSAP. The working environment is a VAX computer. Advantages and limitations of the software and environment, and the impact on final controller design is discussed

Experiences in control system design aided by interactive computer programs: Temperature control of the laser isotope separation vessel

Science.gov (United States)

Gavel, D. T.; Pittenger, L. C.; McDonald, J. S.; Cramer, P. G.; Herget, C. J.

A robust control system has been designed to regulate temperature in a vacuum vessel. The thermodynamic process is modeled by a set of nonlinear, implicit differential equations. The control design and analysis task exercised many of the computer-aided control systems design software packages, including MATLAB, DELIGHT, AND LSAP. The working environment is a VAX computer. Advantages and limitations of the software and environment, and the impact on final controller design is discussed.

VIP: A knowledge-based design aid for the engineering of space systems

Science.gov (United States)

Lewis, Steven M.; Bellman, Kirstie L.

1990-01-01

The Vehicles Implementation Project (VIP), a knowledge-based design aid for the engineering of space systems is described. VIP combines qualitative knowledge in the form of rules, quantitative knowledge in the form of equations, and other mathematical modeling tools. The system allows users rapidly to develop and experiment with models of spacecraft system designs. As information becomes available to the system, appropriate equations are solved symbolically and the results are displayed. Users may browse through the system, observing dependencies and the effects of altering specific parameters. The system can also suggest approaches to the derivation of specific parameter values. In addition to providing a tool for the development of specific designs, VIP aims at increasing the user's understanding of the design process. Users may rapidly examine the sensitivity of a given parameter to others in the system and perform tradeoffs or optimizations of specific parameters. A second major goal of VIP is to integrate the existing corporate knowledge base of models and rules into a central, symbolic form.

A non-linear programming approach to the computer-aided design of regulators using a linear-quadratic formulation

Science.gov (United States)

Fleming, P.

1985-01-01

A design technique is proposed for linear regulators in which a feedback controller of fixed structure is chosen to minimize an integral quadratic objective function subject to the satisfaction of integral quadratic constraint functions. Application of a non-linear programming algorithm to this mathematically tractable formulation results in an efficient and useful computer-aided design tool. Particular attention is paid to computational efficiency and various recommendations are made. Two design examples illustrate the flexibility of the approach and highlight the special insight afforded to the designer.

Computer-aided roll pass design in rolling of airfoil shapes

Science.gov (United States)

Akgerman, N.; Lahoti, G. D.; Altan, T.

1980-01-01

This paper describes two computer-aided design (CAD) programs developed for modeling the shape rolling process for airfoil sections. The first program, SHPROL, uses a modular upper-bound method of analysis and predicts the lateral spread, elongation, and roll torque. The second program, ROLPAS, predicts the stresses, roll separating force, the roll torque and the details of metal flow by simulating the rolling process, using the slab method of analysis. ROLPAS is an interactive program; it offers graphic display capabilities and allows the user to interact with the computer via a keyboard, CRT, and a light pen. The accuracy of the computerized models was evaluated by (a) rolling a selected airfoil shape at room temperature from 1018 steel and isothermally at high temperature from Ti-6Al-4V, and (b) comparing the experimental results with computer predictions. The comparisons indicated that the CAD systems, described here, are useful for practical engineering purposes and can be utilized in roll pass design and analysis for airfoil and similar shapes.

An optimum design on rollers containing the groove with changeable inner diameter based on response surface methodology

Directory of Open Access Journals (Sweden)

Xi Zhao

2016-05-01

Full Text Available In order to realize the precision plastic forming of the revolving body component with changeable wall thickness, a kind of roller containing grooves with changeable inner diameter is put forward, as the forming mould of the technology of rolling-extrusion. Specifically, first, the arc length of the groove in the roller is designed according to the prediction on the forward slip value during the process of forming, to make accurate control of the actual length of the forming segments; then, to obtain better parameters of the roller structure, a second-order response surface model combining finite element numerical simulation and response surface methodology was put forward, taking the factor of forming uniformity as evaluation index. The result of the experiment shows that, for the formed component, not only the size can meet the needs but also each mechanical property index can be greatly improved, which verify the rationality of the forward slip model and the structural parameter of the optimum model based on the response surface methodology.

How to effectively design and create a concept mobile application to aid in the management of type 1 diabetes in adolescents.

Science.gov (United States)

McCulloch, Victoria; Hope, Sarah; Loranger, Brian; Rea, Paul

2017-07-01

Diabetes is one of the most prevalent chronic health conditions in the world; with a range of diabetes-related mobile applications available to the public to aid in glycaemic control and self-management. Statistically, adherence to medication is extremely low in adolescents with Type 1 Diabetes Mellitus (T1DM), therefore, this paper focuses on the research and design of an interactive and educational concept mobile application aimed at early to mid-adolescents to aid in their understanding of T1DM. As visual elements are an essential part of the design, this research outlines how visual components were designed specifically for adolescents with T1DM.

PSAD, a prototype for monitoring and aid to diagnosis of French PWRs

International Nuclear Information System (INIS)

Jousselin, A.; Bourgeois, P.; Busquet, J.L.; Monnier, B.; Mouhamed, B.

1996-01-01

In order to improve safety and availability in its nuclear power plants, EDF has designed a new generation of monitoring systems integrated into a workstation for monitoring and aid to diagnosis (PSAD). These systems perform on-line monitoring of the main power plant components and PSAD stations provide homogenous aids ro diagnosis which enable plant personnel to diagnose the mechanical behavior of plant equipments. The objective of PSAD is to provide them with high-efficiency and user-friendly tools which can considerably free them from routine tasks. PSAD has a flexible architecture, guaranteeing optimum distribution of computing power to make it available where it is needed, thus enhancing the quality of the information. Its architecture includes diagnosis support software based on artificial intelligence technology which can dialogue with real-time or deferred-time processing software and a relational database. The first version of the prototype is working on a french plant at Tricastin. This version includes the software for the host structure and two monitoring functions: the reactor coolant pumps and the turbo-generator monitoring functions. Internal Structures Monitoring function (ISM) and Loose Parts Detection function (LPD) are under development and should be integrated into PSAD prototype in 1996. (author). 5 refs., 6 figs

Confidence interval of intrinsic optimum temperature estimated using thermodynamic SSI model

Institute of Scientific and Technical Information of China (English)

Takaya Ikemoto; Issei Kurahashi; Pei-Jian Shi

2013-01-01

The intrinsic optimum temperature for the development of ectotherms is one of the most important factors not only for their physiological processes but also for ecological and evolutional processes.The Sharpe-Schoolfield-Ikemoto (SSI) model succeeded in defining the temperature that can thermodynamically meet the condition that at a particular temperature the probability of an active enzyme reaching its maximum activity is realized.Previously,an algorithm was developed by Ikemoto (Tropical malaria does not mean hot environments.Journal of Medical Entomology,45,963-969) to estimate model parameters,but that program was computationally very time consuming.Now,investigators can use the SSI model more easily because a full automatic computer program was designed by Shi et al.(A modified program for estimating the parameters of the SSI model.Environmental Entomology,40,462-469).However,the statistical significance of the point estimate of the intrinsic optimum temperature for each ectotherm has not yet been determined.Here,we provided a new method for calculating the confidence interval of the estimated intrinsic optimum temperature by modifying the approximate bootstrap confidence intervals method.For this purpose,it was necessary to develop a new program for a faster estimation of the parameters in the SSI model,which we have also done.

Energy Demand Analysis and Design of a Hybrid Power System in Bawean Islands, Indonesia

Directory of Open Access Journals (Sweden)

Hantoro Ridho

2018-01-01

Full Text Available Over 70 000 000 people in Indonesia have no access to electricity. This study was carried out in Bawean Islands which are located in the Java Sea about 150 km North of Surabaya, the headquarters of East Java. The study to determine the energy services available in the Bawean Island was done through interviewing a random sample of 72 households in two villages namely Komalasa and Lebak. Based on the average monthly electricity consumption of the sampled households connected to the grid, a hybrid renewable energy based electrical supply system was designed for Gili Timur Island, one of the satellite islands around Bawean Island. The system was designed with the aid of a time step simulation software used to design and analyze hybrid power systems. A sensitivity analysis was also carried out on the optimum system to study the effects of variation in some of the system variables. HOMER suggests that for the expected peak load of 131 kW, an optimum system will consist of 150 kW from PV array, two wind turbines each rated 10 kW, a 75 kW diesel generator and batteries for storage.

MVPACK: a package for the computer-aided design of multivariable control systems

International Nuclear Information System (INIS)

Mensah, S.

1984-01-01

The design and analysis of high performing controllers for large complex plants require a collection of interactive, powerful computer software. MVPACK, an open-ended package for the computer aided design of control systems has been developed in the Reactor Control Branch of the Chalk River Nuclear Laboratories. The package is fully interactive, and includes a comprehensive state-of-the-art mathematical library to support development of complex multivariable control algorithms. Coded in RATFOR, MVPACK operates with a flexible data structure which makes efficient use of minicomputer resources and provides a standard framework for program generation. The existence of a help mechanism enhances the simplicity of package utilization. This report provides the technical description of the package. It reviews the specifications used in the design and implementation of the package. The database structure, the supporting libraries and the design and analysis modules of MVPACK are described. The report includes several application examples to illustrate the capability of the package. Experience with MVPACK shows that the package provides a synergistic environment for control and regulation systems design, and that it is a unique tool in training of control system engineers

Hearing aid user guides: suitability for older adults.

Science.gov (United States)

Caposecco, Andrea; Hickson, Louise; Meyer, Carly

2014-02-01

The aim of this study was to analyse the content, design, and readability of printed hearing aid user guides to determine their suitability for older adults, who are the main users of hearing aids. Hearing aid user guides were assessed using four readability formulae and a standardized tool to assess content and design (SAM - Suitability Assessment of Materials). A sample of 36 hearing aid user guides (four user guides from nine different hearing aid manufacturers) were analysed. Sixty nine percent of user guides were rated 'not suitable' and 31% were rated 'adequate' for their suitability. Many scored poorly for scope, vocabulary, aspects of layout and typography, and learning stimulation and motivation. The mean reading grade level for all user guides was grade 9.6 which is too high for older adults. The content, design, and readability of hearing aid user guides are not optimal for older adults and thus may serve as a barrier to successful hearing aid outcomes for this population.

Optimum burnup of BAEC TRIGA research reactor

International Nuclear Information System (INIS)

Lyric, Zoairia Idris; Mahmood, Mohammad Sayem; Motalab, Mohammad Abdul; Khan, Jahirul Haque

2013-01-01

Highlights: ► Optimum loading scheme for BAEC TRIGA core is out-to-in loading with 10 fuels/cycle starting with 5 for the first reload. ► The discharge burnup ranges from 17% to 24% of U235 per fuel element for full power (3 MW) operation. ► Optimum extension of operating core life is 100 MWD per reload cycle. - Abstract: The TRIGA Mark II research reactor of BAEC (Bangladesh Atomic Energy Commission) has been operating since 1986 without any reshuffling or reloading yet. Optimum fuel burnup strategy has been investigated for the present BAEC TRIGA core, where three out-to-in loading schemes have been inspected in terms of core life extension, burnup economy and safety. In considering different schemes of fuel loading, optimization has been searched by only varying the number of fuels discharged and loaded. A cost function has been defined and evaluated based on the calculated core life and fuel load and discharge. The optimum loading scheme has been identified for the TRIGA core, the outside-to-inside fuel loading with ten fuels for each cycle starting with five fuels for the first reload. The discharge burnup has been found ranging from 17% to 24% of U235 per fuel element and optimum extension of core operating life is 100 MWD for each loading cycle. This study will contribute to the in-core fuel management of TRIGA reactor

Optimum Operating Conditions for PZT Actuators for Vibrotactile Wearables

Science.gov (United States)

Logothetis, Irini; Matsouka, Dimitra; Vassiliadis, Savvas; Vossou, Clio; Siores, Elias

2018-04-01

Recently, vibrotactile wearables have received much attention in fields such as medicine, psychology, athletics and video gaming. The electrical components presently used to generate vibration are rigid; hence, the design and creation of ergonomical wearables are limited. Significant advances in piezoelectric components have led to the production of flexible actuators such as piezoceramic lead zirconate titanate (PZT) film. To verify the functionality of PZT actuators for use in vibrotactile wearables, the factors influencing the electromechanical conversion were analysed and tested. This was achieved through theoretical and experimental analyses of a monomorph clamped-free structure for the PZT actuator. The research performed for this article is a three-step process. First, a theoretical analysis presents the equations governing the actuator. In addition, the eigenfrequency of the film was analysed preceding the experimental section. For this stage, by applying an electric voltage and varying the stimulating electrical characteristics (i.e., voltage, electrical waveform and frequency), the optimum operating conditions for a PZT film were determined. The tip displacement was measured referring to the mechanical energy converted from electrical energy. From the results obtained, an equation for the mechanical behaviour of PZT films as actuators was deduced. It was observed that the square waveform generated larger tip displacements. In conjunction with large voltage inputs at the predetermined eigenfrequency, the optimum operating conditions for the actuator were achieved. To conclude, PZT films can be adapted to assist designers in creating comfortable vibrotactile wearables.

A multi-criteria decision aid methodology to design electric vehicles public charging networks

Directory of Open Access Journals (Sweden)

João Raposo

2015-05-01

Full Text Available This article presents a new multi-criteria decision aid methodology, dynamic-PROMETHEE, here used to design electric vehicle charging networks. In applying this methodology to a Portuguese city, results suggest that it is effective in designing electric vehicle charging networks, generating time and policy based scenarios, considering offer and demand and the city’s urban structure. Dynamic-PROMETHE adds to the already known PROMETHEE’s characteristics other useful features, such as decision memory over time, versatility and adaptability. The case study, used here to present the dynamic-PROMETHEE, served as inspiration and base to create this new methodology. It can be used to model different problems and scenarios that may present similar requirement characteristics.

A multi-criteria decision aid methodology to design electric vehicles public charging networks

Science.gov (United States)

Raposo, João; Rodrigues, Ana; Silva, Carlos; Dentinho, Tomaz

2015-05-01

This article presents a new multi-criteria decision aid methodology, dynamic-PROMETHEE, here used to design electric vehicle charging networks. In applying this methodology to a Portuguese city, results suggest that it is effective in designing electric vehicle charging networks, generating time and policy based scenarios, considering offer and demand and the city's urban structure. Dynamic-PROMETHE adds to the already known PROMETHEE's characteristics other useful features, such as decision memory over time, versatility and adaptability. The case study, used here to present the dynamic-PROMETHEE, served as inspiration and base to create this new methodology. It can be used to model different problems and scenarios that may present similar requirement characteristics.

Assessment of the fit of removable partial denture fabricated by computer-aided designing/computer aided manufacturing technology.

Science.gov (United States)

Arafa, Khalid A O

2018-01-01

To assess the level of evidence that supports the quality of fit for removable partial denture (RPD) fabricated by computer-aided designing/computer aided manufacturing (CAD/CAM) and rapid prototyping (RP) technology. Methods: An electronic search was performed in Google Scholar, PubMed, and Cochrane library search engines, using Boolean operators. All articles published in English and published in the period from 1950 until April 2017 were eligible to be included in this review. The total number of articles contained the search terms in any part of the article (including titles, abstracts, or article texts) were screened, which resulted in 214 articles. After exclusion of irrelevant and duplicated articles, 12 papers were included in this systematic review.  Results: All the included studies were case reports, except one study, which was a case series that recruited 10 study participants. The visual and tactile examination in the cast or clinically in the patient's mouth was the most-used method for assessment of the fit of RPDs. From all included studies, only one has assessed the internal fit between RPDs and oral tissues using silicone registration material. The vast majority of included studies found that the fit of RPDs ranged from satisfactory to excellent fit. Conclusion: Despite the lack of clinical trials that provide strong evidence, the available evidence supported the claim of good fit of RPDs fabricated by new technologies using CAD/CAM.

Estimation of Optimum Dilution in the GMAW Process Using Integrated ANN-GA

Directory of Open Access Journals (Sweden)

P. Sreeraj

2013-01-01

Full Text Available To improve the corrosion resistant properties of carbon steel, usually cladding process is used. It is a process of depositing a thick layer of corrosion resistant material over carbon steel plate. Most of the engineering applications require high strength and corrosion resistant materials for long-term reliability and performance. By cladding these properties can be achieved with minimum cost. The main problem faced on cladding is the selection of optimum combinations of process parameters for achieving quality clad and hence good clad bead geometry. This paper highlights an experimental study to optimize various input process parameters (welding current, welding speed, gun angle, and contact tip to work distance and pinch to get optimum dilution in stainless steel cladding of low carbon structural steel plates using gas metal arc welding (GMAW. Experiments were conducted based on central composite rotatable design with full replication technique, and mathematical models were developed using multiple regression method. The developed models have been checked for adequacy and significance. In this study, artificial neural network (ANN and genetic algorithm (GA techniques were integrated and labeled as integrated ANN-GA to estimate optimal process parameters in GMAW to get optimum dilution.

CFD aided approach to design printed circuit heat exchangers for supercritical CO2 Brayton cycle application

International Nuclear Information System (INIS)

Kim, Seong Gu; Lee, Youho; Ahn, Yoonhan; Lee, Jeong Ik

2016-01-01

Highlights: • CFD analyses were performed to find performance of PCHE for supercritical CO 2 power cycle. • CFD results were obtained beyond the limits of existing correlations. • Designs of different PCHEs with different correlations were compared. • A new CFD-aided correlation covering a wider Reynolds number range was proposed. - Abstract: While most conventional PCHE designs for working fluid of supercritical CO 2 require an extension of valid Reynolds number limits of experimentally obtained correlations, Computational Fluid Dynamics (CFD) code ANSYS CFX was used to explore validity of existing correlations beyond their tested Reynolds number ranges. For heat transfer coefficient correlations, an appropriate piece-wising with Ishizuka’s and Hesselgreaves’s correlation is found to enable an extension of Reynolds numbers. For friction factors, no single existing correlation is found to capture different temperature and angular dependencies for a wide Reynolds number range. Based on the comparison of CFD results with the experimentally obtained correlations, a new CFD-aided correlation covering an extended range of Reynolds number 2000–58,000 for Nusselt number and friction factor is proposed to facilitate PCHE designs for the supercritical CO 2 Brayton cycle application.

Marginal accuracy of computer-aided design- and computer-aided manufacturing-fabricated full-arch zirconia restoration.

Science.gov (United States)

Juntavee, Niwut; Sirisathit, Issarawas

2018-01-01

This study evaluated marginal accuracy of full-arch zirconia restoration fabricated from two digital computer-aided design and computer-aided manufacturing (CAD-CAM) systems (Trios-3 and CS3500) in comparison to conventional cast metal restoration. A stainless steel model comprising two canine and two molar abutments was used as a master model for full-arch reconstruction. The canine and molar abutments were machined in a cylindrical shape with 5° taper and chamfer margin. The CAD-CAM systems based on the digital approach were used to construct the full-arch zirconia restoration. The conventional cast metal restoration was fabricated according to a conventional lost-wax technique using nickel-chromium alloys. Ten restorations were fabricated from each system. The marginal accuracy of each restoration was determined at four locations for each abutment. An analysis of variance (ANOVA) and Tukey's honest significant difference (HSD) multiple comparisons were used to determine statistically significant difference at 95% confidence interval. The mean values of marginal accuracy of restorations fabricated from conventional casting, Trios-3, and CS3500 were 48.59±4.16 μm, 53.50±5.66 μm, and 56.47±5.52 μm, respectively. ANOVA indicated significant difference in marginal fit of restorations among various systems. The marginal discrepancy of zirconia restoration fabricated from the CS3500 system demonstrated significantly larger gap than that fabricated from the 3Shape system ( p marginal gap than the conventional cast metal restoration ( p marginal fits than that from the CS3500, although, both were slightly less accurate than the conventional cast restoration. However, the marginal discrepancies of restoration produced by both CAD-CAM systems were within the clinically acceptable range and satisfactorily precise to be suggested for construction full-arch zirconia restoration.

Computer-Aided Facilities Management Systems (CAFM).

Science.gov (United States)

Cyros, Kreon L.

Computer-aided facilities management (CAFM) refers to a collection of software used with increasing frequency by facilities managers. The six major CAFM components are discussed with respect to their usefulness and popularity in facilities management applications: (1) computer-aided design; (2) computer-aided engineering; (3) decision support…

State Student Financial Aid. Report and Recommendations.

Science.gov (United States)

Florida State Postsecondary Education Planning Commission, Tallahassee.

This report presents the results of a review of all state student financial aid programs in Florida and presents recommendations concerning program consolidation. The review was designed to address a variety of aid-related issues, including unexpended financial aid resources, program consolidation, budget request and aid distribution procedures,…

Combining principles of Cognitive Load Theory and diagnostic error analysis for designing job aids : Effects on motivation and diagnostic performance in a process control task

NARCIS (Netherlands)

Kluge, Annette; Grauel, Britta; Burkolter, Dina

Two studies are presented in which the design of a procedural aid and the impact of an additional decision aid for process control were assessed. In Study 1, a procedural aid was developed that avoids imposing unnecessary extraneous cognitive load on novices when controlling a complex technical

Combining principles of Cognitive Load Theory and diagnostic error analysis for designing job aids: Effects on motivation and diagnostic performance in a process control task.

Science.gov (United States)

Kluge, Annette; Grauel, Britta; Burkolter, Dina

2013-03-01

Two studies are presented in which the design of a procedural aid and the impact of an additional decision aid for process control were assessed. In Study 1, a procedural aid was developed that avoids imposing unnecessary extraneous cognitive load on novices when controlling a complex technical system. This newly designed procedural aid positively affected germane load, attention, satisfaction, motivation, knowledge acquisition and diagnostic speed for novel faults. In Study 2, the effect of a decision aid for use before the procedural aid was investigated, which was developed based on an analysis of diagnostic errors committed in Study 1. Results showed that novices were able to diagnose both novel faults and practised faults, and were even faster at diagnosing novel faults. This research contributes to the question of how to optimally support novices in dealing with technical faults in process control. Copyright © 2012 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Analytical and numerical calculations of optimum design frequency for focused ultrasound therapy and acoustic radiation force.

Science.gov (United States)

Ergün, A Sanlı

2011-10-01

Focused ultrasound therapy relies on acoustic power absorption by tissue. The stronger the absorption the higher the temperature increase is. However, strong acoustic absorption also means faster attenuation and limited penetration depth. Hence, there is a trade-off between heat generation efficacy and penetration depth. In this paper, we formulated the acoustic power absorption as a function of frequency and attenuation coefficient, and defined two figures of merit to measure the power absorption: spatial peak of the acoustic power absorption density, and the acoustic power absorbed within the focal area. Then, we derived "rule of thumb" expressions for the optimum frequencies that maximized these figures of merit given the target depth and homogeneous tissue type. We also formulated a method to calculate the optimum frequency for inhomogeneous tissue given the tissue composition for situations where the tissue structure can be assumed to be made of parallel layers of homogeneous tissue. We checked the validity of the rules using linear acoustic field simulations. For a one-dimensional array of 4cm acoustic aperture, and for a two-dimensional array of 4×4cm(2) acoustic aperture, we found that the power absorbed within the focal area is maximized at 0.86MHz, and 0.79MHz, respectively, when the target depth is 4cm in muscle tissue. The rules on the other hand predicted the optimum frequencies for acoustic power absorption as 0.9MHz and 0.86MHz, respectively for the 1D and 2D array case, which are within 6% and 9% of the field simulation results. Because radiation force generated by an acoustic wave in a lossy propagation medium is approximately proportional to the acoustic power absorption, these rules can be used to maximize acoustic radiation force generated in tissue as well. Copyright © 2011 Elsevier B.V. All rights reserved.

Optimum autonomous stand-alone photovoltaic system design on the basis of energy pay-back analysis

International Nuclear Information System (INIS)

Kaldellis, J.K.; Zafirakis, D.; Kondili, E.

2009-01-01

Stand-alone photovoltaic (PV) systems comprise one of the most promising electrification solutions for covering the demand of remote consumers. However, such systems are strongly questioned due to extreme life-cycle (LC) energy requirements. For similar installations to be considered as environmentally sustainable, their LC energy content must be compensated by the respective useful energy production, i.e. their energy pay-back period (EPBP) should be found less than their service period. In this context, an optimum sizing methodology is currently developed, based on the criterion of minimum embodied energy. Various energy autonomous stand-alone PV-lead-acid battery systems are examined and two different cases are investigated; a high solar potential area and a medium solar potential area. By considering that the PV-battery (PV-Bat) system's useful energy production is equal to the remote consumer's electricity consumption, optimum cadmium telluride (CdTe) based systems yield the minimum EPBP (15 years). If achieving to exploit the net PV energy production however, the EPBP is found less than 20 years for all PV types. Finally, the most interesting finding concerns the fact that in all cases examined the contribution of the battery component exceeds 27% of the system LC energy requirements, reflecting the difference between grid-connected and stand-alone configurations.

Optimum filters for narrow-band frequency modulation.

Science.gov (United States)

Shelton, R. D.

1972-01-01

The results of a computer search for the optimum type of bandpass filter for low-index angle-modulated signals are reported. The bandpass filters are discussed in terms of their low-pass prototypes. Only filter functions with constant numerators are considered. The pole locations for the optimum filters of several cases are shown in a table. The results are fairly independent of modulation index and bandwidth.

Design and fabrication of facial prostheses for cancer patient applying computer aided method and manufacturing (CADCAM)

Science.gov (United States)

Din, Tengku Noor Daimah Tengku; Jamayet, Nafij; Rajion, Zainul Ahmad; Luddin, Norhayati; Abdullah, Johari Yap; Abdullah, Abdul Manaf; Yahya, Suzana

2016-12-01

Facial defects are either congenital or caused by trauma or cancer where most of them affect the person appearance. The emotional pressure and low self-esteem are problems commonly related to patient with facial defect. To overcome this problem, silicone prosthesis was designed to cover the defect part. This study describes the techniques in designing and fabrication for facial prosthesis applying computer aided method and manufacturing (CADCAM). The steps of fabricating the facial prosthesis were based on a patient case. The patient was diagnosed for Gorlin Gotz syndrome and came to Hospital Universiti Sains Malaysia (HUSM) for prosthesis. The 3D image of the patient was reconstructed from CT data using MIMICS software. Based on the 3D image, the intercanthal and zygomatic measurements of the patient were compared with available data in the database to find the suitable nose shape. The normal nose shape for the patient was retrieved from the nasal digital library. Mirror imaging technique was used to mirror the facial part. The final design of facial prosthesis including eye, nose and cheek was superimposed to see the result virtually. After the final design was confirmed, the mould design was created. The mould of nasal prosthesis was printed using Objet 3D printer. Silicone casting was done using the 3D print mould. The final prosthesis produced from the computer aided method was acceptable to be used for facial rehabilitation to provide better quality of life.

A comparison of optimum JP and LH2 turbofan engines designed for two subsonic transport missions

Science.gov (United States)

Civinskas, K. C.

1974-01-01

The use of liquid hydrogen fuel instead of JP fuel for two subsonic commercial transports was examined. The following determinations which are important to meeting noise reduction requirements were calculated: (1) take off gross weight, (2) energy consumption, and (3) direct operating costs. The optimum engine cycles were found to be the same for both fuels.

Optimum transformer design for a pulsed power system

International Nuclear Information System (INIS)

Broverman, A.Y.

1987-11-01

Electromagnetic forces resulting from peak pulsed current require special design consideration to prevent failure of the coils of the transformer. Procedures for interleaving transformer windings to reduce both electromagnetic short-circuit forces and reactive voltage drop while reducing procurement costs are described. The basics of transformer design principles and cost trade-offs are included to enhance understanding of the interleaving procedures. 3 refs., 3 figs

Automated platform for designing multiple robot work cells

Science.gov (United States)

Osman, N. S.; Rahman, M. A. A.; Rahman, A. A. Abdul; Kamsani, S. H.; Bali Mohamad, B. M.; Mohamad, E.; Zaini, Z. A.; Rahman, M. F. Ab; Mohamad Hatta, M. N. H.

2017-06-01

Designing the multiple robot work cells is very knowledge-intensive, intricate, and time-consuming process. This paper elaborates the development process of a computer-aided design program for generating the multiple robot work cells which offer a user-friendly interface. The primary purpose of this work is to provide a fast and easy platform for less cost and human involvement with minimum trial and errors adjustments. The automated platform is constructed based on the variant-shaped configuration concept with its mathematical model. A robot work cell layout, system components, and construction procedure of the automated platform are discussed in this paper where integration of these items will be able to automatically provide the optimum robot work cell design according to the information set by the user. This system is implemented on top of CATIA V5 software and utilises its Part Design, Assembly Design, and Macro tool. The current outcomes of this work provide a basis for future investigation in developing a flexible configuration system for the multiple robot work cells.

Achieving optimum diffraction based overlay performance

Science.gov (United States)

Leray, Philippe; Laidler, David; Cheng, Shaunee; Coogans, Martyn; Fuchs, Andreas; Ponomarenko, Mariya; van der Schaar, Maurits; Vanoppen, Peter

2010-03-01

Diffraction Based Overlay (DBO) metrology has been shown to have significantly reduced Total Measurement Uncertainty (TMU) compared to Image Based Overlay (IBO), primarily due to having no measurable Tool Induced Shift (TIS). However, the advantages of having no measurable TIS can be outweighed by increased susceptibility to WIS (Wafer Induced Shift) caused by target damage, process non-uniformities and variations. The path to optimum DBO performance lies in having well characterized metrology targets, which are insensitive to process non-uniformities and variations, in combination with optimized recipes which take advantage of advanced DBO designs. In this work we examine the impact of different degrees of process non-uniformity and target damage on DBO measurement gratings and study their impact on overlay measurement accuracy and precision. Multiple wavelength and dual polarization scatterometry are used to characterize the DBO design performance over the range of process variation. In conclusion, we describe the robustness of DBO metrology to target damage and show how to exploit the measurement capability of a multiple wavelength, dual polarization scatterometry tool to ensure the required measurement accuracy for current and future technology nodes.

Theoretical optimum of implant positional index design.

Science.gov (United States)

Semper, W; Kraft, S; Krüger, T; Nelson, K

2009-08-01

Rotational freedom of the implant-abutment connection influences its screw joint stability; for optimization, influential factors need to be evaluated based on a previously developed closed formula. The underlying hypothesis is that the manufacturing tolerances, geometric pattern, and dimensions of the index do not influence positional stability. We used the dimensions of 5 commonly used implant systems with a clearance of 20 microm to calculate the extent of rotational freedom; a 3D simulation (SolidWorks) validated the analytical findings. Polygonal positional indices showed the highest degrees of rotational freedom. The polygonal profile displayed higher positional stability than the polygons, but less positional accuracy than the cam-groove connection. Features of a maximal rotation-safe positional index were determined. The analytical calculation of rotational freedom of implant positional indices is possible. Rotational freedom is dependent on the geometric design of the index and may be decreased by incorporating specific aspects into the positional index design.

Design alternatives, components key to optimum flares

International Nuclear Information System (INIS)

Cunha-Leite, O.

1992-01-01

A properly designed flare works as an emissions control system with greater than 98% combustion efficiency. The appropriate use of steam, natural gas, and air-assisted flare tips can result in smokeless combustion. Ground flare, otherwise the elevated flare is commonly chosen because it handles larger flow releases more economically. Flaring has become more complicated than just lighting up waste gas. Companies are increasingly concerned about efficiency. In addition, U.S. Occupational Safety and Health Administration (OSHA) and U.S. Environmental Protection Agency (EPA) have become more active, resulting in tighter regulations on both safety and emissions control. These regulations have resulted in higher levels of concern and involvement in safety and emissions matters, not to mention smoke, noise, glare, and odor. This first to two articles on flare design and components looks at elevated flares, flare tips, incinerator-type flares, flare pilots, and gas seals. Part 2 will examine knockout drums, liquid-seal drums, ignition systems, ground flares, vapor recovery systems, and flare noise

Generic Advertising Optimum Budget for Iran’s Milk Industry

Directory of Open Access Journals (Sweden)

H. Shahbazi

2016-05-01

Full Text Available Introduction One of the main targets of planners, decision makers and governments is increasing society health with promotion and production of suitable and healthy food. One of the basic commodities that have important role in satisfaction of required human food is milk. So, some part of government and producer healthy budget allocate to milk consumption promotion by using generic advertising. If effectiveness of advertising budget on profitability is more, producer will have more willing to spend for advertising. Determination of optimal generic advertising budget is one of important problem in managerial decision making in producing firm as well as increase in consumption and profit and decrease in wasting and non-optimality of budget. Materials and Methods: In this study, optimal generic advertising budget intensity index (advertising budget share of production cost was estimated under two different scenarios by using equilibrium replacement model. In equilibrium replacement model, producer surplus are maximized in respect to generic advertising in retail level. According to market where two levels of farm and processing before retail exist and there is trade in farm and retail level, we present different models. Fixed and variable proportion hypothesis is another one. Finally, eight relations are presented for determination of milk generic advertising optimum budget. So, we use data from several resources such as previous studies, national (Iran Static center and international institute (Fao formal data and own estimation. Because there are several estimations in previous studies, we identify some scenarios (in two general scenarios for calculation of milk generic advertising optimum budget. Results and Discussion: Estimation of milk generic advertising optimum budget in scenario 1 shows that in case of one market level, fixed supplies and no trade, optimum budget is 0.4672539 percent. In case of one market level and no trade, optimum

The optimum decision rules for the oddity task

NARCIS (Netherlands)

Versfeld, N.J.; Dai, H.; Green, D.M.

1996-01-01

This paper presents the optimum decision rule for an m-interval oddity task in which m-1 intervals contain the same signal and one is different or odd. The optimum decision rule depends on the degree of correlation among observations. The present approach unifies the different strategies that occur

Optimum unambiguous discrimination of linearly independent pure state

DEFF Research Database (Denmark)

Pang, Shengshi; Wu, Shengjun

2009-01-01

be satisfied by the optimum solution in different situations. We also provide the detailed steps to find the optimum measurement strategy. The method and results we obtain are given a geometrical illustration with a numerical example. Furthermore, using these equations, we derive a formula which shows a clear...

On Optimum Stratification

OpenAIRE

M. G. M. Khan; V. D. Prasad; D. K. Rao

2014-01-01

In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.

Optimum Design Of Grid Connected Photovoltaic System Using Concentrators

Directory of Open Access Journals (Sweden)

Eng. Mohammed Fawzy

2015-08-01

Full Text Available Abstract Due to the increasing demand of electrical energy in Egypt and also in many neighboring countries around the world the main problem facing electrical energy production using classical methods such steam power stations is the depletion of fossil fuels. The gap between the electrical energy demand and the continuous increase on the fossil fuel cost make the problem of electricity generation more sophisticated. With the continuous decrease of the photovoltaic PV technologies cost it doesnt make sense neglecting the importance of electricity production using solar photovoltaic PV especially that the annual average daily energy received is about 6 kamp12310whmamp123112day in Cairo Egypt 30N.In this work a detailed simulation model including photovoltaic PV module characteristics and climatic conditions of Cairo Egypt is developed. The model compares fixed PV systems electrical energy output with photovoltaic PV system using concentrators and double axis tracker systems. The comparison includes the energy generated area required as well as the cost per kwh generated. The optimality criterion is the cost per kwh generated. The system that gives the minimum cost per kwh is the optimum system. To verify the developed model the simulation results of fixed PV modules and CPV using tracking system obtained by the model are compared with practical measurements of 40KW peak station erected in Cairo Egypt 30N.Very good agreement between measured values and results obtained from detailed simulation model. For fixed PV system the detailed economic analysis showed that it gives minimum cost perkwh generated Comparisons among these systems are presented. For Cairo results showed that a cost of about 6 to 9 US centskwh is attainable.

Determination of the Optimum Conditions for Production of Chitosan Nanoparticles

Directory of Open Access Journals (Sweden)

A. Dustgani

2007-12-01

Full Text Available Bioedegradable nanoparticles are intensively investigated for their potential applications in drug delivery systems. Being a biocompatible and biodegradable polymer, chitosan holds great promise for use in this area. This investigation was concerned with determination and optimization of the effective parameters involved in the production of chitosan nanoparticles using ionic gelation method. Studied variables were concentration and pH of the chitosan solution, the ratio of chitosan to sodium tripolyphosphate therein and the molecular weight of chitosan. For this purpose, Taguchistatistical method was used for design of experiments in three levels. The size of chitosan nanoparticle was determined using laser light scattering. The experimental results showed that concentration of chitosan solution was the most important parameter and chitosan molecular weight the least effective parameter. The optimum conditions for preparation of nanoparticles were found to be 1 mg/mL chitosan solution with pH=5, chitosan to sodium tripolyphosphate ratio of 3 and chitosan molecular weight of 200,000 daltons. The average nanoparticle size at optimum conditions was found to be about 150 nm.

Optimum dietary protein requirement of Malaysian mahseer (Tor tambroides) fingerling.

Science.gov (United States)

Misieng, Josephine Dorin; Kamarudin, Mohd Salleh; Musa, Mazlinda

2011-02-01

The optimum dietary protein requirement of the Malaysian mahseer (Tor tambroides) fingerlings was determined in this study. In this completely randomized designed experiment, formulated diets of five levels of dietary protein (30, 35, 40, 45 and 50%) were tested on the T. tambroides fingerlings (initial body weight of 5.85 +/- 0.40 g), reared in aquarium fitted with a biofiltering system. The fingerlings were fed twice daily at 5% of biomass. The fingerling body weight and total length was taken at every two weeks. Mortality was recorded daily. The dietary protein had significant effects on the body weight gain and Specific Growth Rate (SGR) of the fingerlings. The body weight gain and SGR of fingerlings fed with the diet with the dietary protein level of 40% was significantly higher (p<0.05) than that of 30, 35 and 50%. The feed conversion ratio of the 40% dietary protein was the significantly lowest at 2.19 +/- 0.163. The dietary protein level of 40% was the most optimum for T. tambroides fingerlings.

Determining the optimum topology of composites by the flexural stiffness criterion

Directory of Open Access Journals (Sweden)

Vasile MOGA

2012-06-01

Full Text Available An important stage in designing of pieces made of composite materials consists of establishing the composite topology in such a way that it has certain properties needed in exploitation. The paper presents the mathematical apparatus and the calculation programme for establishing the optimum thickness of the composite groups so that it should have certain imposed (given flexural stiffness. The method is applicable to all types of laminate composites, no matter of the cladding or matrix nature. The direct problem consists in determining the thickness of the groups and composite, minimising the bar mass, for an imposed (given flexural stiffness, knowing the densities and elasticity modules of the groups. The indirect problem consists in determining the maximum stiffness, the thickness of the groups and composite for a given (imposed mass, knowing the densities and elasticity modules of the groups. The presented programmes offer to the producer of this kind of materials the possibility to quickly establish the optimum topology.

STRATEGY FOR IMPROVEMENT OF SAFETY AND EFFICIENCY OF COMPUTER-AIDED DESIGN ANALYSIS OF CIVIL ENGINEERING STRUCTURES ON THE BASIS OF THE SYSTEM APPROACH

Directory of Open Access Journals (Sweden)

Zaikin Vladimir Genrikhovich

2012-12-01

Full Text Available The authors highlight three problems of the age of information technologies and proposes the strategy for their resolution in relation to the computer-aided design of civil engineering structures. The authors express their concerns in respect of globalization of software programmes designated for the analysis of civil engineering structures and employed outside of Russia. The problem of the poor quality of the input data has reached Russia. Lately, the rate of accidents of buildings and structures has been growing not only in Russia. Control over efficiency of design projects is hardly performed. This attitude should be changed. Development and introduction of CAD along with the application the efficient methods of projection of behaviour of building structures are in demand. Computer-aided calculations have the function of a logical nucleus, and they need proper control. The system approach to computer-aided calculations and technologies designated for the projection of accidents is formulated by the authors. Two tasks of the system approach and fundamentals of the strategy for its implementation are formulated. The study of cases of negative results of computer-aided design of engineering structures was performed and multi-component design patterns were developed. Conclusions concerning the results of researches aimed at regular and wide-scale implementation of the strategy fundamentals are formulated. Organizational and innovative actions concerning the projected behaviour of civil engineering structures proposed in the strategy are to facilitate: safety and reliability improvement of buildings and structures; saving of building materials and resources; improvement of labour efficiency of designers; modernization and improvement of accuracy of projected behaviour of buildings and building standards; closer ties between civil and building engineering researchers and construction companies; development of competitive environment to boost

AIDS radio triggers.

Science.gov (United States)

Elias, A M

1991-07-01

In April 1991, the Ethnic Communities' Council of NSW was granted funding under the Community AIDS Prevention and Education Program through the Department of Community Services and Health, to produce a series of 6x50 second AIDS radio triggers with a 10-second tag line for further information. The triggers are designed to disseminate culturally-sensitive information about HIV/AIDS in English, Italian, Greek, Spanish, Khmer, Turkish, Macedonian, Serbo-Croatian, Arabic, Cantonese, and Vietnamese, with the goal of increasing awareness and decreasing the degree of misinformation about HIV/AIDS among people of non-English-speaking backgrounds through radio and sound. The 6 triggers cover the denial that AIDS exists in the community, beliefs that words and feelings do not protect one from catching HIV, encouraging friends to be compassionate, compassion within the family, AIDS information for a young audience, and the provision of accurate and honest information on HIV/AIDS. The triggers are slated to be completed by the end of July 1991 and will be broadcast on all possible community, ethnic, and commercial radio networks across Australia. They will be available upon request in composite form with an information kit for use by health care professionals and community workers.

Computer-aided dispatching system design specification

Energy Technology Data Exchange (ETDEWEB)

Briggs, M.G.

1997-12-16

This document defines the performance requirements for a graphic display dispatching system to support Hanford Patrol Operations Center. This document reflects the as-built requirements for the system that was delivered by GTE Northwest, Inc. This system provided a commercial off-the-shelf computer-aided dispatching system and alarm monitoring system currently in operations at the Hanford Patrol Operations Center, Building 2721E. This system also provides alarm back-up capability for the Plutonium Finishing Plant (PFP).

Computer-aided dispatching system design specification

International Nuclear Information System (INIS)

Briggs, M.G.

1997-01-01

This document defines the performance requirements for a graphic display dispatching system to support Hanford Patrol Operations Center. This document reflects the as-built requirements for the system that was delivered by GTE Northwest, Inc. This system provided a commercial off-the-shelf computer-aided dispatching system and alarm monitoring system currently in operations at the Hanford Patrol Operations Center, Building 2721E. This system also provides alarm back-up capability for the Plutonium Finishing Plant (PFP)

Analytical evaluation of computer-based decision aids

International Nuclear Information System (INIS)

Kisner, R.A.

1985-01-01

This paper introduces a method for evaluating decision aids for nuclear power plant operators. The method involves a two-stage process of classification and analytical evaluation of display form and content. The classification scheme relates each specific aid to one or more general decision-making tasks. Evaluation then proceeds using a normative top-down design process based on the classification scheme by determining or deducing how various design issues associated with this process were resolved by the designer. The result is an assessment of the ''understandability'' of the aid as well as identification of the training and display features necessary to ensure understandability. 7 refs., 4 figs., 1 tab

Analysis of the Optimum Gain of a High-Pass L-Matching Network for Rectennas.

Science.gov (United States)

Gasulla, Manel; Jordana, Josep; Robert, Francesc-Josep; Berenguer, Jordi

2017-07-25

Rectennas, which mainly consist of an antenna, matching network, and rectifier, are used to harvest radiofrequency energy in order to power tiny sensor nodes, e.g., the nodes of the Internet of Things. This paper demonstrates for the first time, the existence of an optimum voltage gain for high-pass L-matching networks used in rectennas by deriving an analytical expression. The optimum gain is that which leads to maximum power efficiency of the rectenna. Here, apart from the L-matching network, a Schottky single-diode rectifier was used for the rectenna, which was optimized at 868 MHz for a power range from -30 dBm to -10 dBm. As the theoretical expression depends on parameters not very well-known a priori, an accurate search of the optimum gain for each power level was performed via simulations. Experimental results show remarkable power efficiencies ranging from 16% at -30 dBm to 55% at -10 dBm, which are for almost all the tested power levels the highest published in the literature for similar designs.

Analysis of the Optimum Gain of a High-Pass L-Matching Network for Rectennas

Directory of Open Access Journals (Sweden)

Manel Gasulla

2017-07-01

Full Text Available Rectennas, which mainly consist of an antenna, matching network, and rectifier, are used to harvest radiofrequency energy in order to power tiny sensor nodes, e.g., the nodes of the Internet of Things. This paper demonstrates for the first time, the existence of an optimum voltage gain for high-pass L-matching networks used in rectennas by deriving an analytical expression. The optimum gain is that which leads to maximum power efficiency of the rectenna. Here, apart from the L-matching network, a Schottky single-diode rectifier was used for the rectenna, which was optimized at 868 MHz for a power range from −30 dBm to −10 dBm. As the theoretical expression depends on parameters not very well-known a priori, an accurate search of the optimum gain for each power level was performed via simulations. Experimental results show remarkable power efficiencies ranging from 16% at −30 dBm to 55% at −10 dBm, which are for almost all the tested power levels the highest published in the literature for similar designs.

[A computer aided design approach of all-ceramics abutment for maxilla central incisor].

Science.gov (United States)

Sun, Yu-chun; Zhao, Yi-jiao; Wang, Yong; Han, Jing-yun; Lin, Ye; Lü, Pei-jun

2010-10-01

To establish the computer aided design (CAD) software platform of individualized abutment for the maxilla central incisor. Three-dimentional data of the incisor was collected by scanning and geometric transformation. Data mainly included the occlusal part of the healing abutment, the location carinae of the bedpiece, the occlusal 1/3 part of the artificial gingiva's inner surface, and so on. The all-ceramic crown designed in advanced was "virtual cutback" to get the original data of the abutment's supragingival part. The abutment's in-gum part was designed to simulate the individual natural tooth root. The functions such as "data offset", "bi-rail sweep surface" and "loft surface" were used in the process of CAD. The CAD route of the individualized all-ceramic abutment was set up. The functions and application methods were decided and the complete CAD process was realized. The software platform was basically set up according to the requests of the dental clinic.

Correction of Pectus Excavatum by Custom-Made Silicone Implants: Contribution of Computer-Aided Design Reconstruction. A 20-Year Experience and 401 Cases.

Science.gov (United States)

Chavoin, Jean-Pierre; Grolleau, Jean-Louis; Moreno, Benjamin; Brunello, Jérémie; André, Aymeric; Dahan, Marcel; Garrido, Ignacio; Chaput, Benoit

2016-05-01

In the absence of demonstrable functional impairment, pectus excavatum is merely a congenital deformity, albeit with a marked psychological impact. Many patients do not wish to undergo thoracic remodeling operations, which are invasive and do not clearly result in respiratory or cardiac improvement. From 1993 to 2015, the authors designed 401 custom-made silicone implants to treat funnel chests. Before 2007, implants were made from plaster chest molds. Beginning in 2007, three-dimensional reconstructions were made from computed tomographic scans by computer-aided design. The authors prospectively recorded all assessments and follow-up data since 1993. Preoperative and postoperative photographs of two random groups of 50 patients were analyzed, in a blinded manner, by two surgeons independently. Intraoperative and postoperative complications, clinical outcomes, patient satisfaction, and quality of life were evaluated. One infection and three hematomas were recorded. Periprosthetic seroma was evident in all cases. Patients rated the cosmetic outcomes of computer-aided design implants significantly higher than those of the earlier implants made using plaster molds (p = 0.030). Malformations were better corrected in the computer-aided design group (86 percent) than in the plaster group (72 percent) (p = 0.038). Patient satisfaction was higher in the former group (p = 0.011). Medical Outcomes Study 36-Item Short-Form Health Survey scores revealed significant improvements, both socially and emotionally. Correction of pectus excavatum using a computer-aided design silicone implant fulfils aesthetic and psychological demands. The technique is simple and reliable and yields high-quality results. In the medium term, the approach may render invasive techniques obsolete. These operations remain risky and of doubtful functional utility. Therapeutic, III.

Optimum MRS site location to minimize spent fuel transportation impacts

International Nuclear Information System (INIS)

Hoskins, R.E.

1987-01-01

A range of spent fuel transportation system parameters are examined in terms of attributes important to minimizing transportation impacts as a basis for identifying geographic regions best suited for siting a monitored retrievable storage (MRS) facility. Transportation system parameters within existing transport cask design and transportation mode capabilities were systematically analyzed. The optimum MRS location was found to be very sensitive to transportation system assumptions particularly with regard to the relative efficiencies of the reactor-to-MRS and MRS-to-repository components of the system. Moreover, dramatic improvements in the reactor-to-MRS component can be made through use of multiple cask shipment of the largest practical casks by dedicated train compared to the traditional single cask rail (70%) and truck (30%) shipments assumed the Department of Energy in their studies that defined the optimum MRS location in the vicinity of Tennessee. It is important to develop and utilize an efficient transportation system irrespective of whether or not an MRS is in the system. Assuming reasonably achievable efficiency in reactor-to-MRS spent fuel transportation and assigning equal probabilities to the three western sites selected for characterization of being the repository site, the optimum MRS location would be in the far-mid-western states. Based on various geographic criteria including barge access and location in a nuclear service area, the State of Tennessee ranks any place from 12th to the 25th at a penalty of about 30% over the minimum achievable impacts. While minimizing transportation impacts is an important factor, other criteria should also be considered in selecting an MRS site

HIV-induced immunodeficiency and mortality from AIDS-defining and non-AIDS-defining malignancies

DEFF Research Database (Denmark)

Monforte, Antonella d'Arminio; Abrams, Donald; Pradier, Christian

2008-01-01

OBJECTIVE: To evaluate deaths from AIDS-defining malignancies (ADM) and non-AIDS-defining malignancies (nADM) in the D:A:D Study and to investigate the relationship between these deaths and immunodeficiency. DESIGN: Observational cohort study. METHODS: Patients (23 437) were followed prospectively......-fold higher latest CD4 cell count was associated with a halving of the risk of ADM mortality. Other predictors of an increased risk of ADM mortality were homosexual risk group, older age, a previous (non-malignancy) AIDS diagnosis and earlier calendar years. Predictors of an increased risk of nADM mortality...

Creation of system of computer-aided design for technological objects

Science.gov (United States)

Zubkova, T. M.; Tokareva, M. A.; Sultanov, N. Z.

2018-05-01

Due to the competition in the market of process equipment, its production should be flexible, retuning to various product configurations, raw materials and productivity, depending on the current market needs. This process is not possible without CAD (computer-aided design). The formation of CAD begins with planning. Synthesizing, analyzing, evaluating, converting operations, as well as visualization and decision-making operations, can be automated. Based on formal description of the design procedures, the design route in the form of an oriented graph is constructed. The decomposition of the design process, represented by the formalized description of the design procedures, makes it possible to make an informed choice of the CAD component for the solution of the task. The object-oriented approach allows us to consider the CAD as an independent system whose properties are inherited from the components. The first step determines the range of tasks to be performed by the system, and a set of components for their implementation. The second one is the configuration of the selected components. The interaction between the selected components is carried out using the CALS standards. The chosen CAD / CAE-oriented approach allows creating a single model, which is stored in the database of the subject area. Each of the integration stages is implemented as a separate functional block. The transformation of the CAD model into the model of the internal representation is realized by the block of searching for the geometric parameters of the technological machine, in which the XML-model of the construction is obtained on the basis of the feature method from the theory of image recognition. The configuration of integrated components is divided into three consecutive steps: configuring tasks, components, interfaces. The configuration of the components is realized using the theory of "soft computations" using the Mamdani fuzzy inference algorithm.

‘Optimum mobility’ facelift. Part 2 – the technique

OpenAIRE

Fanous, Nabil; Karsan, Naznin; Zakhary, Kristina; Tawile, Carolyne

2006-01-01

In the first of this two-part article on the ‘optimum mobility’ facelift, facial tissue mobility was analyzed, and three theories or mechanisms emerged: ‘intrinsic mobility’, ‘surgically induced mobility’ and ‘optimum mobility points’.

The optimum size of rotating qarḍ ḥasan savings and credit associations

Directory of Open Access Journals (Sweden)

Seyed Kazem Sadr

2017-07-01

Full Text Available Purpose - Several indigenous credit and savings schemes have been accredited recently in developing countries for the benefit of households and entrepreneurs alike. Famous among them are the Rotating Savings and Credit Associations (ROSCAs that exist in almost all continents currently. The rapid development of ROSCAs and their varied structures in many countries have been the subject of numerous studies. What has not been thoroughly analysed is the optimum size of these associations and the fact that lending and borrowing is without interest. The aim of this paper is to present a model that would determine the optimum size of ROSCAs and deal with the following issues: how the group size varies with changes in the income level of the members, the demand for the loan, the size of the collected loan and its duration. Further, the question of whether or not lending to the association in return for obtaining larger sums is a violation of the qarḍ (loan contract is dealt with, and several Sharīʿah compatible formulations are provided. Design/methodology/approach - Economic analysis has been applied to show the optimum size of Qarḍ Ḥasan Associations (QHAs, which are the Sharīʿah-compliant equivalent of ROSCAs, and the Sharīʿah rules of the qarḍ contract to illustrate the legitimacy of group lending. Findings - The major findings of this study are determination of the optimum size of QHAs, the factors that affect the size and suggestion of alternative legal forms for group financing. Research limitations/implications - Inaccessibility to sources of data to test the hypothesis that has been put forth is the main difficulty encountered when conducting research on the subject. Practical implications - The paper concludes that the development of informal interest-free ROSCAs in both Muslim and non-Muslim countries is an efficient informal microfinance scheme and that it is compatible with Sharīʿah rules. Originality/value - The optimum size

Pembuatan pupuk bokashi dari sampah lingkungan berdasarkan rancangan percobaan campuran yang optimum pada model permukaan multirespon

Directory of Open Access Journals (Sweden)

Ruslan Ruslan

2012-02-01

Full Text Available Environment waste arround ITS college such as waste of Trembesi leaves, Sono leaves, and Satintail at this research will be used as part of materials of Bokashi fertilizer producing. The first aim of this research produced Bokashi fertilizer in various proportion waste of Trembesi leaves, Sono leaves, and Satintail with other materials proportion which has been assumed to be constant based ondevelopment of optimum mixture design of multiresponse surface theory by D-optimum criterion. The second aim of this research was compared 5:3:1:1 composition from reference to 5:2:1:2 composition from researcher hypothesis with proportion of waste of Trembesi leaves, Sono leaves, and Satintail as independent variables to N, P, and K percentation as response variables. Optimum mixture designsof multiresponse surface model will be optimum if it weighted w = 1qs means the each point of experiment will be given s-replications as much as proportion number of experiment point to number of component. The 5:2:1:2 and 5:3:1:1 compositions of Bokashi fertilizer producing are not statistically difference, therefore both compositions can be used to produce Bokashi fertilizer.

Using computer-aided drug design and medicinal chemistry strategies in the fight against diabetes.

Science.gov (United States)

Semighini, Evandro P; Resende, Jonathan A; de Andrade, Peterson; Morais, Pedro A B; Carvalho, Ivone; Taft, Carlton A; Silva, Carlos H T P

2011-04-01

The aim of this work is to present a simple, practical and efficient protocol for drug design, in particular Diabetes, which includes selection of the illness, good choice of a target as well as a bioactive ligand and then usage of various computer aided drug design and medicinal chemistry tools to design novel potential drug candidates in different diseases. We have selected the validated target dipeptidyl peptidase IV (DPP-IV), whose inhibition contributes to reduce glucose levels in type 2 diabetes patients. The most active inhibitor with complex X-ray structure reported was initially extracted from the BindingDB database. By using molecular modification strategies widely used in medicinal chemistry, besides current state-of-the-art tools in drug design (including flexible docking, virtual screening, molecular interaction fields, molecular dynamics, ADME and toxicity predictions), we have proposed 4 novel potential DPP-IV inhibitors with drug properties for Diabetes control, which have been supported and validated by all the computational tools used herewith.

A Self-Instructional Course in Student Financial Aid Administration. Module 15: Internal Aid Office Management and Institutional Quality Control. Second Edition.

Science.gov (United States)

Washington Consulting Group, Inc., Washington, DC.

The 15th in a 17-module self-instructional course on student financial aid administration (designed for novice financial aid administrators and other institutional personnel) focuses on internal aid office management and institutional quality control. The course provides a systematic introduction to the management of federal financial aid programs…

Determination method of optimum pre-stress in cables of cable-stayed bridges by using fuzzy sets theory; Fuzzy riron wo mochiita shachokyo cable no saiteki prestress chikara ketteiho

Energy Technology Data Exchange (ETDEWEB)

Furuta, H. [Kansai Univ., Osaka (Japan); Kaneyoshi, M.; Tanaka, H. [Hitachi Zosen Corp., Osaka (Japan); Kamei, M.

1996-06-20

Generally in cable-stayed bridges, optimum pre-stress is introduced into cables to achieve reducing weight of the cable cross section by reducing and equalizing the cross sectional force of the main girders. However, the conventional optimum stress determining methods require setting the cross section to be repeated. Therefore, in order to omit iterative calculations and derive rational pre-stress, a fuzzy sets theory was introduced. With this method, if upper and lower limits of design values (targeted design values) are inputted, which are desired by a designer to be realized as cross sectional force such as in main girders and towers and cable tension, an optimum stress can be derived automatically by means of a fuzzy linearity regression analysis. The targeted design values are given by experience and engineering judgment, and resetting the cross section is not required as long as a target value which can be tolerated by a hypothetical cross section is given. Since the theory used is a fuzzy sets theory, the derived pre-stress may not be guaranteed as a truly optimum pre-stress. In order to have the result approach an optimum solution, it is important to set adequate upper and lower limits of the targeted design values referring to examples of constructions in the past and experience. 10 refs., 11 figs., 7 tabs.

Consideration of Insulin Pumps or Continuous Glucose Monitors by Adolescents With Type 1 Diabetes and Their Parents: Stakeholder Engagement in the Design of Web-Based Decision Aids.

Science.gov (United States)

Wysocki, Tim; Hirschfeld, Fiona; Miller, Louis; Izenberg, Neil; Dowshen, Steven A; Taylor, Alex; Milkes, Amy; Shinseki, Michelle T; Bejarano, Carolina; Kozikowski, Chelsea; Kowal, Karen; Starr-Ashton, Penny; Ross, Judith L; Kummer, Mark; Carakushansky, Mauri; Lyness, D'Arcy; Brinkman, William; Pierce, Jessica; Fiks, Alexander; Christofferson, Jennifer; Rafalko, Jessica; Lawson, Margaret L

2016-08-01

This article describes the stakeholder-driven design, development, and testing of web-based, multimedia decision aids for youth with type 1 diabetes who are considering the insulin pump or continuous glucose monitoring and their parents. This is the initial phase of work designed to develop and evaluate the efficacy of these decision aids in promoting improved decision-making engagement with use of a selected device. Qualitative interviews of 36 parents and adolescents who had previously faced these decisions and 12 health care providers defined the content, format and structure of the decision aids. Experts in children's health media helped the research team to plan, create, and refine multimedia content and its presentation. A web development firm helped organize the content into a user-friendly interface and enabled tracking of decision aid utilization. Throughout, members of the research team, adolescents, parents, and 3 expert consultants offered perspectives about the website content, structure, and function until the design was complete. With the decision aid websites completed, the next phase of the project is a randomized controlled trial of usual clinical practice alone or augmented by use of the decision aid websites. Stakeholder-driven development of multimedia, web-based decision aids requires meticulous attention to detail but can yield exceptional resources for adolescents and parents contemplating major changes to their diabetes regimens. © 2016 The Author(s).

Kansas Nursing Home Medication Aide Curriculum. Revised.

Science.gov (United States)

Bartel, Myrna J.; Fornelli, Linda K.

This curriculum guide is designed to aid Kansas instructors in conducting a course for teaching nursing home medication aides. Covered first are various introductory topics such as the role and responsibilities of medication aides, pharmacodynamics, forms in which medication is now available, common medical abbreviations, mathematics and weights…

Estimation and Uncertainty Analysis of Flammability Properties for Computer-aided molecular design of working fluids for thermodynamic cycles

DEFF Research Database (Denmark)

Frutiger, Jerome; Abildskov, Jens; Sin, Gürkan

Computer Aided Molecular Design (CAMD) is an important tool to generate, test and evaluate promising chemical products. CAMD can be used in thermodynamic cycle for the design of pure component or mixture working fluids in order to improve the heat transfer capacity of the system. The safety......, there is no information about the reliability of the data. Furthermore, the global optimality of the GC parameters estimation is often not ensured....

Problem of determining optimum geological and technical measures

Energy Technology Data Exchange (ETDEWEB)

Osipov, G N; Roste, Z A; Salimzhanov, E S

1968-01-01

This article is concerned with the mathematical simulation of oilfield operation, particularly the use of linear programing to determine optimum conditions for exploitation of a field. The basic approach is to define the field operation by a series of equations, apply boundary conditions and through an iterative computer technique find optimum operating conditions. Application of the method to Tuimazy field is illustrated.

Conservation and aid: designing more effective investments in natural resource governance reform.

Science.gov (United States)

Nelson, Fred

2009-10-01

Biodiversity conservation outcomes are closely related to the rules and institutions governing resource use. Creating local incentives for conservation through more secure resource tenure is central to conservation outcomes on private and communal lands, where the preponderance of biodiversity occurs. Conservation efforts in sub-Saharan Africa are therefore centrally concerned with governance dynamics and institutional reform processes, such as the decentralization of property rights, and how best to achieve such reforms. Traditional mechanisms for financing conservation efforts in Africa rely heavily on funds channeled through multilateral and bilateral aid agencies. The history of development aid highlights a range of constraints these aid agencies face in terms of working toward more effective resource governance arrangements and promoting reforms. Government aid agencies possess incentives for promoting large-scale and short-term projects that maximize expenditure volumes and tend to define issues in technical rather than political terms. The history of development aid suggests that these and other characteristics of aid agencies impedes their ability to influence governance reform processes and that aid funding may discourage the adoption of reforms. Greater emphasis in African conservation financing needs to be placed on flexible, small-scale investments aligned to local interests and constituencies that prioritize innovation, learning, and experimentation. Additionally, more research is required that explores the linkages between conservation funding, donor decision-making processes, and governance reforms.

Applications of the NRGsuite and the Molecular Docking Software FlexAID in Computational Drug Discovery and Design.

Science.gov (United States)

Morency, Louis-Philippe; Gaudreault, Francis; Najmanovich, Rafael

2018-01-01

Docking simulations help us understand molecular interactions. Here we present a hands-on tutorial to utilize FlexAID (Flexible Artificial Intelligence Docking), an open source molecular docking software between ligands such as small molecules or peptides and macromolecules such as proteins and nucleic acids. The tutorial uses the NRGsuite PyMOL plugin graphical user interface to set up and visualize docking simulations in real time as well as detect and refine target cavities. The ease of use of FlexAID and the NRGsuite combined with its superior performance relative to widely used docking software provides nonexperts with an important tool to understand molecular interactions with direct applications in structure-based drug design and virtual high-throughput screening.

Heuristic lipophilicity potential for computer-aided rational drug design

Science.gov (United States)

Du, Qishi; Arteca, Gustavo A.; Mezey, Paul G.

1997-09-01

In this contribution we suggest a heuristic molecular lipophilicitypotential (HMLP), which is a structure-based technique requiring noempirical indices of atomic lipophilicity. The input data used in thisapproach are molecular geometries and molecular surfaces. The HMLP is amodified electrostatic potential, combined with the averaged influences fromthe molecular environment. Quantum mechanics is used to calculate theelectron density function ρ(r) and the electrostatic potential V(r), andfrom this information a lipophilicity potential L(r) is generated. The HMLPis a unified lipophilicity and hydrophilicity potential. The interactions ofdipole and multipole moments, hydrogen bonds, and charged atoms in amolecule are included in the hydrophilic interactions in this model. TheHMLP is used to study hydrogen bonds and water-octanol partitioncoefficients in several examples. The calculated results show that the HMLPgives qualitatively and quantitatively correct, as well as chemicallyreasonable, results in cases where comparisons are available. Thesecomparisons indicate that the HMLP has advantages over the empiricallipophilicity potential in many aspects. The HMLP is a three-dimensional andeasily visualizable representation of molecular lipophilicity, suggested asa potential tool in computer-aided three-dimensional drug design.

Statistical Shape Analysis of the Human Ear Canal with Application to In-the-Ear Hearing Aid Design

DEFF Research Database (Denmark)

Paulsen, Rasmus Reinhold

2004-01-01

This thesis is about the statistical shape analysis of the human ear canal with application to the mechanical design of in-the-ear hearing aids. Initially, it is described how a statistical shape model of the human ear canal is built based on a training set of laser-scanned ear impressions. A thin...

A framework of cloud supported collaborative design in glass lens moulds based on aspheric measurement

Science.gov (United States)

Zhu, Yongjian; Wang, Yu; Na, Jingxin; Zhi, Yanan; Fan, Yufeng

2013-09-01

Aspheric mould design includes the top-down design and reversal design. In this paper, a new framework of reversal design is proposed combining with cloud supported collaborative design (CSCD) based on aspheric measurement. The framework is a kind of collaborative platform, which is composed of eight modules, including the computerized aspheric precision measurement module (CAPM), computer-aided optical design of aspheric lens system (CAOD), computer-aided design of lens mould (CADLM), FEM(finite element method) simulation of lens molding module (FEMLM), computer-aided manufacture of lens and moulds (CAMLM), measurement data analysis module (MDAM), optical product lifecycle management module (OPLM) and cloud computing network module (CCNM). In this framework, the remote clients send an improved requirement or fabrication demand about optical lens system through CCNM, which transfers this signal to OPLM. In OPLM, one main server is in charge of the task distribution and collaborative work of other six modules. The first measurement data of aspheric lens are produced by clients or our proposed platform CAPM, then are sent to CAOD for optimization and the electronic drawings of lens moulds are generated in CADLM module. According the design drawings, the FEMLM could give the lens-molding simulation parameters through FEM software. The simulation data are used for the second design of moulds in CADLM module. In this case, the moulds could be fabricated in CAMLM by ultra-precision machine, and the aspheric lens could be also produced by lens-molding machine in CAMLM. At last, the final shape of aspheric lens could be measured in CAPM and the data analysis could be conducted in MDAM module. Through the proposed framework, all the work described above could be performed coordinately. And the optimum design data of lens mould could be realized and saved, then shared by all the work team.

Tax Efficiency vs. Tax Equity – Points of View regarding Tax Optimum

Directory of Open Access Journals (Sweden)

Stela Aurelia Toader

2011-10-01

Full Text Available Objectives. Starting from the idea that tax equity requirements, administration costs and the tendency towards tax evasion determine the design of tax systems, it is important to identify a satisfactory efficiency/equity deal in order to build a tax system as close to optimum requirements as possible. Prior Work Previous studies proved that an optimum tax system is that through which it will be collected a level of tax revenues which will satisfy budgetary demands, while losing only a minimum ‘amount’ of welfare. In what degree the Romanian tax system meets these requirements? Approach We envisage analyzing the possibilities of improving Romanian tax system as to come nearest to optimum requirements. Results We can conclude fiscal system can uphold important improvements in what assuring tax equity is concerned, resulting in raising the degree of free conformation in the field of tax payment and, implicitly, the degree of tax efficiency. Implications Knowing to what extent it can be acted upon in the direction of finding that satisfactory efficiency/equity deal may allow oneself to identify the blueprint of a tax system in which the loss of welfare is kept down to minimum. Value For the Romanian institutions empowered to impose taxes, the knowledge of the possibilities of making the tax system more efficient can be important while aiming at reducing the level of evasion phenomenon.

Statistical Power and Optimum Sample Allocation Ratio for Treatment and Control Having Unequal Costs Per Unit of Randomization

Science.gov (United States)

Liu, Xiaofeng

2003-01-01

This article considers optimal sample allocation between the treatment and control condition in multilevel designs when the costs per sampling unit vary due to treatment assignment. Optimal unequal allocation may reduce the cost from that of a balanced design without sacrificing any power. The optimum sample allocation ratio depends only on the…

Optimum design of heat exchanger for environmental control system of an aircraft using entropy generation minimization (EGM) technique

CSIR Research Space (South Africa)

Bello-Ochende, T

2016-07-01

Full Text Available in the system are incorporated in the numerical analysis to minimize the exergy destruction of the system. The ECS analysed was based on a bootstrap air cycle with two cooling streams; ram air and air bled from engine fan. The paper proposes optimum air...

46 CFR 108.707 - First aid kit.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false First aid kit. 108.707 Section 108.707 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Miscellaneous Equipment § 108.707 First aid kit. Each unit must have a first-aid kit approved by the Mine Safety...

Development of a computer-aided design software for dental splint in orthognathic surgery

Science.gov (United States)

Chen, Xiaojun; Li, Xing; Xu, Lu; Sun, Yi; Politis, Constantinus; Egger, Jan

2016-12-01

In the orthognathic surgery, dental splints are important and necessary to help the surgeon reposition the maxilla or mandible. However, the traditional methods of manual design of dental splints are difficult and time-consuming. The research on computer-aided design software for dental splints is rarely reported. Our purpose is to develop a novel special software named EasySplint to design the dental splints conveniently and efficiently. The design can be divided into two steps, which are the generation of initial splint base and the Boolean operation between it and the maxilla-mandibular model. The initial splint base is formed by ruled surfaces reconstructed using the manually picked points. Then, a method to accomplish Boolean operation based on the distance filed of two meshes is proposed. The interference elimination can be conducted on the basis of marching cubes algorithm and Boolean operation. The accuracy of the dental splint can be guaranteed since the original mesh is utilized to form the result surface. Using EasySplint, the dental splints can be designed in about 10 minutes and saved as a stereo lithography (STL) file for 3D printing in clinical applications. Three phantom experiments were conducted and the efficiency of our method was demonstrated.

Optimum target thickness for polarimeters

International Nuclear Information System (INIS)

Sitnik, I.M.

2003-01-01

Polarimeters with thick targets are a tool to measure the proton polarization. But the question about the optimum target thickness is still the subject of discussion. An attempt to calculate the most common parameters concerning this problem, in a few GeV region, is made

Computer-Aided Modeling of Lipid Processing Technology

DEFF Research Database (Denmark)

Diaz Tovar, Carlos Axel

2011-01-01

increase along with growing interest in biofuels, the oleochemical industry faces in the upcoming years major challenges in terms of design and development of better products and more sustainable processes to make them. Computer-aided methods and tools for process synthesis, modeling and simulation...... are widely used for design, analysis, and optimization of processes in the chemical and petrochemical industries. These computer-aided tools have helped the chemical industry to evolve beyond commodities toward specialty chemicals and ‘consumer oriented chemicals based products’. Unfortunately...... to develop systematic computer-aided methods (property models) and tools (database) related to the prediction of the necessary physical properties suitable for design and analysis of processes employing lipid technologies. The methods and tools include: the development of a lipid-database (CAPEC...

New layer-based imaging and rapid prototyping techniques for computer-aided design and manufacture of custom dental restoration.

Science.gov (United States)

Lee, M-Y; Chang, C-C; Ku, Y C

2008-01-01

Fixed dental restoration by conventional methods greatly relies on the skill and experience of the dental technician. The quality and accuracy of the final product depends mostly on the technician's subjective judgment. In addition, the traditional manual operation involves many complex procedures, and is a time-consuming and labour-intensive job. Most importantly, no quantitative design and manufacturing information is preserved for future retrieval. In this paper, a new device for scanning the dental profile and reconstructing 3D digital information of a dental model based on a layer-based imaging technique, called abrasive computer tomography (ACT) was designed in-house and proposed for the design of custom dental restoration. The fixed partial dental restoration was then produced by rapid prototyping (RP) and computer numerical control (CNC) machining methods based on the ACT scanned digital information. A force feedback sculptor (FreeForm system, Sensible Technologies, Inc., Cambridge MA, USA), which comprises 3D Touch technology, was applied to modify the morphology and design of the fixed dental restoration. In addition, a comparison of conventional manual operation and digital manufacture using both RP and CNC machining technologies for fixed dental restoration production is presented. Finally, a digital custom fixed restoration manufacturing protocol integrating proposed layer-based dental profile scanning, computer-aided design, 3D force feedback feature modification and advanced fixed restoration manufacturing techniques is illustrated. The proposed method provides solid evidence that computer-aided design and manufacturing technologies may become a new avenue for custom-made fixed restoration design, analysis, and production in the 21st century.

Design and application of location error teaching aids in measuring and visualization

Directory of Open Access Journals (Sweden)

Yu Fengning

2015-01-01

Full Text Available As an abstract concept, ‘location error’ in is considered to be an important element with great difficult to understand and apply. The paper designs and develops an instrument to measure the location error. The location error is affected by different position methods and reference selection. So we choose position element by rotating the disk. The tiny movement transfers by grating ruler and programming by PLC can show the error on text display, which also helps students understand the position principle and related concepts of location error. After comparing measurement results with theoretical calculations and analyzing the measurement accuracy, the paper draws a conclusion that the teaching aid owns reliability and a promotion of high value.

Molecular structure descriptors in the computer-aided design of biologically active compounds

International Nuclear Information System (INIS)

Raevsky, Oleg A

1999-01-01

The current state of description of molecular structure in computer-aided molecular design of biologically active compounds by means of descriptors is analysed. The information contents of descriptors increases in the following sequence: element-level descriptors-structural formulae descriptors-electronic structure descriptors-molecular shape descriptors-intermolecular interaction descriptors. Each subsequent class of descriptors normally covers information contained in the previous-level ones. It is emphasised that it is practically impossible to describe all the features of a molecular structure in terms of any single class of descriptors. It is recommended to optimise the number of descriptors used by means of appropriate statistical procedures and characteristics of structure-property models based on these descriptors. The bibliography includes 371 references.

Computer-aided and predictive models for design of controlled release of pesticides

DEFF Research Database (Denmark)

Suné, Nuria Muro; Gani, Rafiqul

2004-01-01

In the field of pesticide controlled release technology, a computer based model that can predict the delivery of the Active Ingredient (AI) from fabricated units is important for purposes of product design and marketing. A model for the release of an M from a microcapsule device is presented...... in this paper, together with a specific case study application to highlight its scope and significance. The paper also addresses the need for predictive models and proposes a computer aided modelling framework for achieving it through the development and introduction of reliable and predictive constitutive...... models. A group-contribution based model for one of the constitutive variables (AI solubility in polymers) is presented together with examples of application and validation....

A Preliminary Study on the Effect of Computer-Aided Designed and Manufactured Orthoses on Chronic Plantar Heel Pain.

Science.gov (United States)

Gatt, Alfred; Grech, Mark; Chockalingam, Nachiappan; Formosa, Cynthia

2018-04-01

Chronic plantar heel pain (CPHP) is a significant, painful condition referring to a range of undifferentiated foot conditions that affect the heel of the foot. Participants presenting with CPHP of more than 6 months' duration were recruited on a first through the door basis. Computer-Aided Design and Computer-Aided Manufactured (CAD-CAM) orthoses were designed and constructed for each participant, then dispensed as per normal practice. Pre- and postintervention assessment of pain was performed at baseline and after 6 weeks of use, utilizing the pain subset of the Foot Function Index (FFI). There was a significant reduction in the mean pain scores for all participants in all constructs of the FFI. Total FFI score was also significant ( P = .003). CAD-CAM orthoses have the potential to become a treatment modality of choice in CPHP since they have resulted in a significant improvement in heel pain after only 6 weeks' use. Therapeutic, Level IV: Prospective, comparative trial.

Optimum strategies for nuclear energy system development (method of synthesis)

International Nuclear Information System (INIS)

Belenky, V.Z.

1983-01-01

The problem of optimum long-term development of the nuclear energy system is considered. The optimum strategies (i.e. minimum total uranium consumption) for the transition phase leading to a stationary regime of development are found. For this purpose the author has elaborated a new method of solving linear problems of optimal control which can include jumps in trajectories. The method gives a possibility to fulfil a total synthesis of optimum strategies. A key characteristic of the problem is the productivity function of the nuclear energy system which connects technological system parameters with its growth rate. There are only two types of optimum strategies, according to an increasing or decreasing productivity function. Both cases are illustrated with numerical examples. (orig.) [de

An Analysis of Computer Aided Design (CAD) Packages Used at MSFC for the Recent Initiative to Integrate Engineering Activities

Science.gov (United States)

Smith, Leigh M.; Parker, Nelson C. (Technical Monitor)

2002-01-01

This paper analyzes the use of Computer Aided Design (CAD) packages at NASA's Marshall Space Flight Center (MSFC). It examines the effectiveness of recent efforts to standardize CAD practices across MSFC engineering activities. An assessment of the roles played by management, designers, analysts, and manufacturers in this initiative will be explored. Finally, solutions are presented for better integration of CAD across MSFC in the future.

A Novel Criterion for Optimum MultilevelCoding Systems in Mobile Fading Channels