Evaluation of geological documents available for provisional safety analyses of potential sites for nuclear waste repositories - Are additional geological investigations needed?

International Nuclear Information System (INIS)

2010-10-01

The procedure for selecting repository sites for all categories of radioactive waste in Switzerland is defined in the conceptual part of the Sectoral Plan for Deep Geological Repositories, which foresees a selection of sites in three stages. In Stage I, Nagra proposed geological siting regions based on criteria relating to safety and engineering feasibility. The Swiss Government (the Federal Council) is expected to decide on the siting proposals in 2011. The objective of Stage 2 is to prepare proposals for the location of the surface facilities within the planning perimeters defined by the Federal Council in its decision on Stage 1 and to identify potential sites. Nagra also has to carry out a provisional safety analysis for each site and a safety-based comparison of the sites. Based on this, and taking into account the results of the socio-economic-ecological impact studies, Nagra then has to propose at least two sites for each repository type to be carried through to Stage 3. The proposed sites will then be investigated in more detail in Stage 3 to ensure that the selection of the sites for the General Licence Applications is well founded. In order to realise the objectives of the upcoming Stage 2, the state of knowledge of the geological conditions at the sites has to be sufficient to perform the provisional safety analyses. Therefore, in preparation for Stage 2, the conceptual part of the Sectoral Plan requires Nagra to clarify the need for additional investigations aimed at providing input for the provisional safety analyses. The purpose of the present report is to document Nagra's technical-scientific assessment of this need. The focus is on evaluating the geological information based on processes and parameters that are relevant for safety and engineering feasibility. In evaluating the state of knowledge the key question is whether additional information could lead to a different decision regarding the selection of the sites to be carried through to Stage 3

Risk Aversion in Game Shows

DEFF Research Database (Denmark)

Andersen, Steffen; Harrison, Glenn W.; Lau, Morten I.

2008-01-01

We review the use of behavior from television game shows to infer risk attitudes. These shows provide evidence when contestants are making decisions over very large stakes, and in a replicated, structured way. Inferences are generally confounded by the subjective assessment of skill in some games......, and the dynamic nature of the task in most games. We consider the game shows Card Sharks, Jeopardy!, Lingo, and finally Deal Or No Deal. We provide a detailed case study of the analyses of Deal Or No Deal, since it is suitable for inference about risk attitudes and has attracted considerable attention....

Radiochemical methods and spectroscopical analyses for investigating the catalytic effects of 2-methyltetrahydro-anthraquinone and phenanthraquinone in wood pulp production using the soda additive method

International Nuclear Information System (INIS)

Besser, R. v.

1982-01-01

The studies were to show whether 2-methyltetrahydroanthraquinone or phenanthraquinone, two additives obtainable at low cost, will have a suitable catalytic effect on the delignification using the soda additive pulping method. For this purpose, soda cookings have been made in a 7 l rotary autoclave. The results have shown that 2-MeTHAQ is by far the better catalytic agent. Further experiments have been made to investigate the mode of action of the redox additives, intended to reveal further characteristics which can be correlated with the knowledge obtained from the preceding soda cookings. The analysis shows that there is a connection between the analytical lignin characteristics and the effectiveness of quinoid additives. (orig./PW) [de

The behaviour of molybdenum dialkyldithiocarbamate friction modifier additives

International Nuclear Information System (INIS)

Graham, Jocelyn Claire Herries

2001-01-01

In recent years there has been growing concern to produce energy-efficient lubricated components and modem engine oil specifications require lubricants to demonstrate fuel efficiency in standardised engine tests. One important method of producing low friction and thus fuel-efficient lubricants is to use oil-soluble, molybdenum-containing, friction modifier additives. In optimal conditions these additives are able to produce very low friction coefficients, in the range 0.045 to 0.075 in boundary lubrication conditions. Very little is known about the chemical and physical mechanisms by which oil soluble molybdenum additives form low friction films in tribological contacts. Information about their activity could lead to optimal use of these additives in lubricants and, therefore, more efficient engine running. The work outlined in this thesis investigated the behaviour of oil-soluble molybdenum additives and showed that these additives were able to effectively reduce friction in the absence of other additives such as ZnDTP. Their activity was shown to be highly concentration and temperature dependent and was also found to be sensitive to the roughness of the contacting surfaces. Raman spectroscopy was used to analyse the chemical nature of molybdenum-containing reaction films and found that friction reduction indubitably arises from the local formation of platelets (diameter 30-50 nm) of MoS 2 . The formation of MoS 2 -rich films was found to occur only during direct asperity-asperity rubbing of the contacting surfaces (this type of contact being especially prevalent in pure sliding contacts). At elevated temperatures and in the presence of oxidising gases the consumption of MoDTC was monitored. MoDTC concentration dropped until the total value fell below a critical level to reduce friction. The study showed that decay rate of molybdenum-containing species was reduced by the addition of peroxide-decomposing antioxidants. (author)

Application of Natural Mineral Additives in Construction

Science.gov (United States)

Linek, Malgorzata; Nita, Piotr; Wolka, Paweł; Zebrowski, Wojciech

2017-12-01

The article concerns the idea of using selected mineral additives in the pavement quality concrete composition. The basis of the research paper was the modification of cement concrete intended for airfield pavements. The application of the additives: metakaolonite and natural zeolite was suggested. Analyses included the assessment of basic physical properties of modifiers. Screening analysis, assessment of micro structure and chemical microanalysis were conducted in case of these materials. The influence of the applied additives on the change of concrete mix parameters was also presented. The impact of zeolite and metakaolinite on the mix density, oxygen content and consistency class was analysed. The influence of modifiers on physical and mechanical changes of the hardened cement concrete was discussed (concrete density, compressive strength and bending strength during fracturing) in diversified research periods. The impact of the applied additives on the changes of internal structure of cement concrete was discussed. Observation of concrete micro structure was conducted using the scanning electron microscope. According to the obtained lab test results, parameters of the applied modifiers and their influence on changes of internal structure of cement concrete are reflected in the increase of mechanical properties of pavement quality concrete. The increase of compressive and bending strength in case of all analysed research periods was proved.

Orange-flavored soft drink with the addition of isolated whey protein

Directory of Open Access Journals (Sweden)

Mirian Souza Prado

2015-08-01

Full Text Available Current assay developed an orange-flavored soda pop with the addition of isolated whey protein, bottled in a 2L-polyethylene terephthalate container and stored at room temperature for 90 days. Physical, chemical, microbiological and sensorial analyses were conducted periodically on the product. The physicochemical analysis showed pH 3.53, 11.5ºBrix and 224 mg of citric acid per 100 mL of the drink and the following proximal composition: protein 0.501%, humidity 88.9%, ash 0.084% and carbohydrates 10.5%. Microbiological analyses detected no microorganisms during the storage period of the drink. Sensorial analysis results had good acceptability. Results showed that the product is stable when stored at room temperature for 90 days. This beverage contains higher nutritional rates and the same calorie rates when compared to sodas and some oranges juices found on the consumer market.

The intervals method: a new approach to analyse finite element outputs using multivariate statistics

Directory of Open Access Journals (Sweden)

Jordi Marcé-Nogué

2017-10-01

Full Text Available Background In this paper, we propose a new method, named the intervals’ method, to analyse data from finite element models in a comparative multivariate framework. As a case study, several armadillo mandibles are analysed, showing that the proposed method is useful to distinguish and characterise biomechanical differences related to diet/ecomorphology. Methods The intervals’ method consists of generating a set of variables, each one defined by an interval of stress values. Each variable is expressed as a percentage of the area of the mandible occupied by those stress values. Afterwards these newly generated variables can be analysed using multivariate methods. Results Applying this novel method to the biological case study of whether armadillo mandibles differ according to dietary groups, we show that the intervals’ method is a powerful tool to characterize biomechanical performance and how this relates to different diets. This allows us to positively discriminate between specialist and generalist species. Discussion We show that the proposed approach is a useful methodology not affected by the characteristics of the finite element mesh. Additionally, the positive discriminating results obtained when analysing a difficult case study suggest that the proposed method could be a very useful tool for comparative studies in finite element analysis using multivariate statistical approaches.

The intervals method: a new approach to analyse finite element outputs using multivariate statistics

Science.gov (United States)

De Esteban-Trivigno, Soledad; Püschel, Thomas A.; Fortuny, Josep

2017-01-01

Background In this paper, we propose a new method, named the intervals’ method, to analyse data from finite element models in a comparative multivariate framework. As a case study, several armadillo mandibles are analysed, showing that the proposed method is useful to distinguish and characterise biomechanical differences related to diet/ecomorphology. Methods The intervals’ method consists of generating a set of variables, each one defined by an interval of stress values. Each variable is expressed as a percentage of the area of the mandible occupied by those stress values. Afterwards these newly generated variables can be analysed using multivariate methods. Results Applying this novel method to the biological case study of whether armadillo mandibles differ according to dietary groups, we show that the intervals’ method is a powerful tool to characterize biomechanical performance and how this relates to different diets. This allows us to positively discriminate between specialist and generalist species. Discussion We show that the proposed approach is a useful methodology not affected by the characteristics of the finite element mesh. Additionally, the positive discriminating results obtained when analysing a difficult case study suggest that the proposed method could be a very useful tool for comparative studies in finite element analysis using multivariate statistical approaches. PMID:29043107

Identification of irradiated food additives by photostimulated luminescence (PSL) method

International Nuclear Information System (INIS)

Yun, Hye Jeong; Kwon, Joong Ho; KIm, Dong Ho; Hur, Jung Mu; Yang, Suh Yung; Lee, Byoung Hun

2008-01-01

Photostimulated luminescence (PSL), electron spin resonance (ESR) and thermoluminescence (TL) analyses were conducted to detect whether 258 kinds of extracted and powdered forms food additives were irradiated or not. In a view of the PSL results, 9 kinds of the extracted and powdered samples (3.2%) showed over 5,000 photon counts (60 sec) -1 and these samples were judged to be irradiation-positive. Thirty nine kinds of the samples (15.6%) yielded 700-5,000 photon counts (60 sec) -1 and these samples were grouped into irradiation-potential, while the samples showed below 700 photon counts (60 sec) -1 sec were judged to be irradiation-negative. TL glow curves for minerals separated from 5 samples were detected at 150 degrees C with high intensity. However, TL analysis did not apply to other irradiation-positive and irradiation-potential samples because the minerals for TL detection were not separated from the samples. ESR measurements for irradiation-positive and irradiation-potential samples, judged by PSL detection, showed no specific signals to irradiation. The results indicated that PSL could be applied to identify irradiation treatment of extracted and powdered food additives, while TL was optional and ESR was not suitable for detection extracted and powdered food additives

Preliminary Analyses Showed Short-Term Mental Health Improvements after a Single-Day Manager Training.

Science.gov (United States)

Boysen, Elena; Schiller, Birgitta; Mörtl, Kathrin; Gündel, Harald; Hölzer, Michael

2018-01-10

Psychosocial working conditions attract more and more attention when it comes to mental health in the workplace. Trying to support managers to deal with their own as well as their employees' psychological risk factors, we conducted a specific manager training. Within this investigation, we wanted to learn about the training's effects and acceptance. A single-day manager training was provided in a large industrial company in Germany. The participants were asked to fill out questionnaires regarding their own physical and mental health condition as well as their working situation. Questionnaires were distributed at baseline, 3-month, and 12-month follow-up. At this point of time the investigation is still ongoing. The current article focuses on short-term preliminary effects. Analyses only included participants that already completed baseline and three months follow-up. Preliminary results from three-month follow-up survey ( n = 33, nmale = 30, Mage = 47.5) indicated positive changes in the manager's mental health condition measured by the Patient Health Questionnaire for depression (PHQ-9: Mt1 = 3.82, Mt2 = 3.15). Training managers about common mental disorders and risk factors at the workplace within a single-day workshop seems to promote positive effects on their own mental health. Especially working with the managers on their own early stress symptoms might have been an important element.

Addition of different tuna meal levels to pizza dough

Directory of Open Access Journals (Sweden)

Daniel Abreu Vasconcelos Campelo

Full Text Available Abstract The aim of this study was to develop pizza dough with different levels of tuna meal (Tunnus spp.. In order to produce tuna meal, tuna torsos without fins were used, cooked for 1 hour, pressed, milled and dehydrated for 24 hours at 60 °C. Pizza dough was produced without (0% or with the addition of 5, 10, 15 and 20% of tuna meal, calculated based on the quantity of wheat flour. The tuna meal and different pizza pastries were analyzed for moisture content, crude protein, total lipids, ash, carbohydrates, caloric value and fatty acid profiles. Microbiological and sensory analyses were also carried out on the pizza pastries. The increasing addition of tuna meal resulted in gains in the crude protein (10.89 to 18.94%, total lipid (4.63 to 5.89% and ash (2.54 to 3.54% contents of the pizza pastries, not influencing the moisture content or caloric value. The inclusion of tuna meal linearly increased the quantity of n-3 series fatty acids in the pizza pastry, from 1.56 to 5.93 g/kg with the addition of 20% tuna meal. The ratio between the polyunsaturated and saturated fatty acids in the tuna meal and pizza pastries varied from 1.21 to 1.85. The microbiological analyses showed that the pizza pastries were produced under proper hygiene conditions. It was also observed that the addition of 5 to 20% of tuna meal to the pizza pastry did not significantly (p>0.05 alter the parameters of aroma, flavor, overall impression and purchase intention. It was therefore concluded that the addition of 5 to 20% tuna meal is effective in improving the nutritional value and fatty acid profile of pizza pastry.

Uncertainty and Sensitivity Analyses Plan

International Nuclear Information System (INIS)

Simpson, J.C.; Ramsdell, J.V. Jr.

1993-04-01

Hanford Environmental Dose Reconstruction (HEDR) Project staff are developing mathematical models to be used to estimate the radiation dose that individuals may have received as a result of emissions since 1944 from the US Department of Energy's (DOE) Hanford Site near Richland, Washington. An uncertainty and sensitivity analyses plan is essential to understand and interpret the predictions from these mathematical models. This is especially true in the case of the HEDR models where the values of many parameters are unknown. This plan gives a thorough documentation of the uncertainty and hierarchical sensitivity analysis methods recommended for use on all HEDR mathematical models. The documentation includes both technical definitions and examples. In addition, an extensive demonstration of the uncertainty and sensitivity analysis process is provided using actual results from the Hanford Environmental Dose Reconstruction Integrated Codes (HEDRIC). This demonstration shows how the approaches used in the recommended plan can be adapted for all dose predictions in the HEDR Project

Indian Point 2 steam generator tube rupture analyses

International Nuclear Information System (INIS)

Dayan, A.

1985-01-01

Analyses were conducted with RETRAN-02 to study consequences of steam generator tube rupture (SGTR) events. The Indian Point, Unit 2, power plant (IP2, PWR) was modeled as a two asymmetric loops, consisting of 27 volumes and 37 junctions. The break section was modeled once, conservatively, as a 150% flow area opening at the wall of the steam generator cold leg plenum, and once as a 200% double-ended tube break. Results revealed 60% overprediction of breakflow rates by the traditional conservative model. Two SGTR transients were studied, one with low-pressure reactor trip and one with an earlier reactor trip via over temperature ΔT. The former is more typical to a plant with low reactor average temperature such as IP2. Transient analyses for a single tube break event over 500 seconds indicated continued primary subcooling and no need for steam line pressure relief. In addition, SGTR transients with reactor trip while the pressurizer still contains water were found to favorably reduce depressurization rates. Comparison of the conservative results with independent LOFTRAN predictions showed good agreement

Fractal and multifractal analyses of bipartite networks

Science.gov (United States)

Liu, Jin-Long; Wang, Jian; Yu, Zu-Guo; Xie, Xian-Hua

2017-03-01

Bipartite networks have attracted considerable interest in various fields. Fractality and multifractality of unipartite (classical) networks have been studied in recent years, but there is no work to study these properties of bipartite networks. In this paper, we try to unfold the self-similarity structure of bipartite networks by performing the fractal and multifractal analyses for a variety of real-world bipartite network data sets and models. First, we find the fractality in some bipartite networks, including the CiteULike, Netflix, MovieLens (ml-20m), Delicious data sets and (u, v)-flower model. Meanwhile, we observe the shifted power-law or exponential behavior in other several networks. We then focus on the multifractal properties of bipartite networks. Our results indicate that the multifractality exists in those bipartite networks possessing fractality. To capture the inherent attribute of bipartite network with two types different nodes, we give the different weights for the nodes of different classes, and show the existence of multifractality in these node-weighted bipartite networks. In addition, for the data sets with ratings, we modify the two existing algorithms for fractal and multifractal analyses of edge-weighted unipartite networks to study the self-similarity of the corresponding edge-weighted bipartite networks. The results show that our modified algorithms are feasible and can effectively uncover the self-similarity structure of these edge-weighted bipartite networks and their corresponding node-weighted versions.

Phenotypic and functional analyses show stem cell-derived hepatocyte-like cells better mimic fetal rather than adult hepatocytes.

Science.gov (United States)

Baxter, Melissa; Withey, Sarah; Harrison, Sean; Segeritz, Charis-Patricia; Zhang, Fang; Atkinson-Dell, Rebecca; Rowe, Cliff; Gerrard, Dave T; Sison-Young, Rowena; Jenkins, Roz; Henry, Joanne; Berry, Andrew A; Mohamet, Lisa; Best, Marie; Fenwick, Stephen W; Malik, Hassan; Kitteringham, Neil R; Goldring, Chris E; Piper Hanley, Karen; Vallier, Ludovic; Hanley, Neil A

2015-03-01

Hepatocyte-like cells (HLCs), differentiated from pluripotent stem cells by the use of soluble factors, can model human liver function and toxicity. However, at present HLC maturity and whether any deficit represents a true fetal state or aberrant differentiation is unclear and compounded by comparison to potentially deteriorated adult hepatocytes. Therefore, we generated HLCs from multiple lineages, using two different protocols, for direct comparison with fresh fetal and adult hepatocytes. Protocols were developed for robust differentiation. Multiple transcript, protein and functional analyses compared HLCs to fresh human fetal and adult hepatocytes. HLCs were comparable to those of other laboratories by multiple parameters. Transcriptional changes during differentiation mimicked human embryogenesis and showed more similarity to pericentral than periportal hepatocytes. Unbiased proteomics demonstrated greater proximity to liver than 30 other human organs or tissues. However, by comparison to fresh material, HLC maturity was proven by transcript, protein and function to be fetal-like and short of the adult phenotype. The expression of 81% phase 1 enzymes in HLCs was significantly upregulated and half were statistically not different from fetal hepatocytes. HLCs secreted albumin and metabolized testosterone (CYP3A) and dextrorphan (CYP2D6) like fetal hepatocytes. In seven bespoke tests, devised by principal components analysis to distinguish fetal from adult hepatocytes, HLCs from two different source laboratories consistently demonstrated fetal characteristics. HLCs from different sources are broadly comparable with unbiased proteomic evidence for faithful differentiation down the liver lineage. This current phenotype mimics human fetal rather than adult hepatocytes. Copyright © 2014 European Association for the Study of the Liver. Published by Elsevier B.V. All rights reserved.

Antiwear and antioxidant studies of cardanol phosphate ester additives

Energy Technology Data Exchange (ETDEWEB)

Mazzetto, S.E.; Oliveira, L.D.M.; Lomonaco, D.; Veloso, P.A., E-mail: selma@ufc.br [Lab. de Produtos e Tecnologia em Processos (LPT), Dept. de Quimica Organica e Inorganica, Universidade Federal do Ceara, Fortaleza, CE (Brazil)

2012-07-15

In the search for new applications and products derived from Cashew Nut Shell Liquid (CNSL), we report herein the synthesis and characterization (GC/MS and {sup 1}H, {sup 13}C, and {sup 31}P NMR) of four phosphate esters derived from hydrogenated cardanol, including their applications as antiwear additives for diesel (S500) and as antioxidant additives for mineral oils, evaluated through the HFRR test and oxidative stability analyses, respectively. The results obtained showed very good to excellent performances promoted by the bioadditives evaluated, especially for the thiophosphorylated derivative, which notably reduced the sludge residue and the acidity index of the oxidized oil (0.52 mg NaOH/g sample) and also improved the diesel lubricity, reducing the wear of metal parts by more than 50% (330 {Mu}m). Keywords: Cardanol; Antiwear; Antioxidant; Diesel; Mineral oil. (author)

Is the classical law of the addition of probabilities violated in quantum interference?

International Nuclear Information System (INIS)

Arsenovic, Dusan; Bozic, Mirjana; Vuskovic, Lepsa

2002-01-01

We analyse and compare the positive and negative arguments on whether quantum interference violates the classical law of the addition of probabilities. The analysis takes into account the results of recent interference experiments in neutron, electron and atom optics. Nonclassical behaviour of atoms was found in atomic experiments where the measurements included their time of arrival and space distribution. We determine probabilities of elementary events associated with the nonclassical behaviour of particles in interferometers. We show that the emergence of the interference pattern in the process of accumulation of such elementary events is consistent with the classical law of the addition of probabilities

Anti-Vascular Endothelial Growth Factor Comparative Effectiveness Trial for Diabetic Macular Edema: Additional Efficacy Post Hoc Analyses of a Randomized Clinical Trial.

Science.gov (United States)

Jampol, Lee M; Glassman, Adam R; Bressler, Neil M; Wells, John A; Ayala, Allison R

2016-12-01

Post hoc analyses from the Diabetic Retinopathy Clinical Research Network randomized clinical trial comparing aflibercept, bevacizumab, and ranibizumab for diabetic macular edema (DME) might influence interpretation of study results. To provide additional outcomes comparing 3 anti-vascular endothelial growth factor (VEGF) agents for DME. Post hoc analyses performed from May 3, 2016, to June 21, 2016, of a randomized clinical trial performed from August 22, 2012, to September 23, 2015, of 660 participants comparing 3 anti-VEGF treatments in eyes with center-involved DME causing vision impairment. Randomization to intravitreous aflibercept (2.0 mg), bevacizumab (1.25 mg), or ranibizumab (0.3 mg) administered up to monthly based on a structured retreatment regimen. Focal/grid laser treatment was added after 6 months for the treatment of persistent DME. Change in visual acuity (VA) area under the curve and change in central subfield thickness (CST) within subgroups based on whether an eye received laser treatment for DME during the study. Post hoc analyses were performed for 660 participants (mean [SD] age, 61 [10] years; 47% female, 65% white, 16% black or African American, 16% Hispanic, and 3% other). For eyes with an initial VA of 20/50 or worse, VA improvement was greater with aflibercept than the other agents at 1 year but superior only to bevacizumab at 2 years. Mean (SD) letter change in VA over 2 years (area under curve) was greater with aflibercept (+17.1 [9.7]) than with bevacizumab (+12.1 [9.4]; 95% CI, +1.6 to +7.3; P grid laser treatment was performed for DME, the only participants to have a substantial reduction in mean CST between 1 and 2 years were those with a baseline VA of 20/50 or worse receiving bevacizumab and laser treatment (mean [SD], -55 [108] µm; 95% CI, -82 to -28 µm; P grid laser treatment, ceiling and floor effects, or both may account for mean thickness reductions noted only in bevacizumab-treated eyes between 1 and 2 years

Five Kepler target stars that show multiple transiting exoplanet candidates

Energy Technology Data Exchange (ETDEWEB)

Steffen, Jason H.; /Fermilab; Batalha, Natalie M.; /San Jose State U.; Borucki, William J.; /NASA, Ames; Buchhave, Lars A.; /Harvard-Smithsonian Ctr. Astrophys. /Bohr Inst.; Caldwell, Douglas A.; /NASA, Ames /SETI Inst., Mtn. View; Cochran, William D.; /Texas U.; Endl, Michael; /Texas U.; Fabrycky, Daniel C.; /Harvard-Smithsonian Ctr. Astrophys.; Fressin, Francois; /Harvard-Smithsonian Ctr. Astrophys.; Ford, Eric B.; /Florida U.; Fortney, Jonathan J.; /UC, Santa Cruz, Phys. Dept. /NASA, Ames

2010-06-01

We present and discuss five candidate exoplanetary systems identified with the Kepler spacecraft. These five systems show transits from multiple exoplanet candidates. Should these objects prove to be planetary in nature, then these five systems open new opportunities for the field of exoplanets and provide new insights into the formation and dynamical evolution of planetary systems. We discuss the methods used to identify multiple transiting objects from the Kepler photometry as well as the false-positive rejection methods that have been applied to these data. One system shows transits from three distinct objects while the remaining four systems show transits from two objects. Three systems have planet candidates that are near mean motion commensurabilities - two near 2:1 and one just outside 5:2. We discuss the implications that multitransiting systems have on the distribution of orbital inclinations in planetary systems, and hence their dynamical histories; as well as their likely masses and chemical compositions. A Monte Carlo study indicates that, with additional data, most of these systems should exhibit detectable transit timing variations (TTV) due to gravitational interactions - though none are apparent in these data. We also discuss new challenges that arise in TTV analyses due to the presence of more than two planets in a system.

Statistical analyses of extreme food habits

International Nuclear Information System (INIS)

Breuninger, M.; Neuhaeuser-Berthold, M.

2000-01-01

This report is a summary of the results of the project ''Statistical analyses of extreme food habits'', which was ordered from the National Office for Radiation Protection as a contribution to the amendment of the ''General Administrative Regulation to paragraph 45 of the Decree on Radiation Protection: determination of the radiation exposition by emission of radioactive substances from facilities of nuclear technology''. Its aim is to show if the calculation of the radiation ingested by 95% of the population by food intake, like it is planned in a provisional draft, overestimates the true exposure. If such an overestimation exists, the dimension of it should be determined. It was possible to prove the existence of this overestimation but its dimension could only roughly be estimated. To identify the real extent of it, it is necessary to include the specific activities of the nuclides, which were not available for this investigation. In addition to this the report shows how the amounts of food consumption of different groups of foods influence each other and which connections between these amounts should be taken into account, in order to estimate the radiation exposition as precise as possible. (orig.) [de

Meta-analyses of HFE variants in coronary heart disease.

Science.gov (United States)

Lian, Jiangfang; Xu, Limin; Huang, Yi; Le, Yanping; Jiang, Danjie; Yang, Xi; Xu, Weifeng; Huang, Xiaoyan; Dong, Changzheng; Ye, Meng; Zhou, Jianqing; Duan, Shiwei

2013-09-15

HFE gene variants can cause hereditary hemochromatosis (HH) that often comes along with an increased risk of coronary heart disease (CHD). The goal of our study is to assess the contribution of four HFE gene variants to the risk of CHD. We conducted four meta-analyses of the studies examining the association between four HFE gene variants and the risk of CHD. A systematic search was conducted using MEDLINE, EMBASE, Web of Science and China National Knowledge Infrastructure (CNKI), Wanfang Chinese Periodical. Meta-analyses showed that HFE rs1799945-G allele was associated with a 6% increased risk of CHD (P=0.02, odds ratio (OR)=1.06, 95% confidence interval (CI)=1.01-1.11). However, no association between the other three HFE gene variants (rs1800562, rs1800730, and rs9366637) and CHD risk was observed by the meta-analyses (all P values>0.05). In addition, the results of our case-control study indicated that rs1800562 and rs1800730 were monomorphic, and that rs1799945 and rs9366637 were not associated with CHD in Han Chinese. Our meta-analysis suggested that a significant association existed between rs1799945 mutation and CHD, although this mutation was rare in Han Chinese. Copyright © 2013 Elsevier B.V. All rights reserved.

Long-term uranium supply-demand analyses

International Nuclear Information System (INIS)

1986-12-01

It is the intention of this study to investigate the long-term uranium supply demand situation using a number of supply and demand related assumptions. For supply, these assumptions as used in the Resources and Production Projection (RAPP) model include country economic development status, and consequent lead times for exploration and development, uranium development status, country infrastructure, and uranium resources including the Reasonably Assured (RAR), Estimated Additional, Categories I and II, (EAR-I and II) and Speculative Resource categories. The demand assumptions were based on the ''pure'' reactor strategies developed by the NEA Working Party on Nuclear Fuel Cycle Requirements for the 1986 OECD (NEA)/IAEA reports ''Nuclear Energy and its Fuel Cycle: Prospects to 2025''. In addition for this study, a mixed strategy case was computed using the averages of the Plutonium (Pu) burning LWR high, and the improved LWR low cases. It is understandable that such a long-term analysis cannot present hard facts, but it can show which variables may in fact influence the long-term supply-demand situation. It is hoped that results of this study will provide valuable information for planners in the uranium supply and demand fields. Periodical re-analyses with updated data bases will be needed from time to time

Characterization of Metal Powders Used for Additive Manufacturing.

Science.gov (United States)

Slotwinski, J A; Garboczi, E J; Stutzman, P E; Ferraris, C F; Watson, S S; Peltz, M A

2014-01-01

Additive manufacturing (AM) techniques can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process.

Characterization of Metal Powders Used for Additive Manufacturing

Science.gov (United States)

Slotwinski, JA; Garboczi, EJ; Stutzman, PE; Ferraris, CF; Watson, SS; Peltz, MA

2014-01-01

Additive manufacturing (AM) techniques1 can produce complex, high-value metal parts, with potential applications as critical parts, such as those found in aerospace components. The production of AM parts with consistent and predictable properties requires input materials (e.g., metal powders) with known and repeatable characteristics, which in turn requires standardized measurement methods for powder properties. First, based on our previous work, we assess the applicability of current standardized methods for powder characterization for metal AM powders. Then we present the results of systematic studies carried out on two different powder materials used for additive manufacturing: stainless steel and cobalt-chrome. The characterization of these powders is important in NIST efforts to develop appropriate measurements and standards for additive materials and to document the property of powders used in a NIST-led additive manufacturing material round robin. An extensive array of characterization techniques was applied to these two powders, in both virgin and recycled states. The physical techniques included laser diffraction particle size analysis, X-ray computed tomography for size and shape analysis, and optical and scanning electron microscopy. Techniques sensitive to structure and chemistry, including X-ray diffraction, energy dispersive analytical X-ray analysis using the X-rays generated during scanning electron microscopy, and X-Ray photoelectron spectroscopy were also employed. The results of these analyses show how virgin powder changes after being exposed to and recycled from one or more Direct Metal Laser Sintering (DMLS) additive manufacturing build cycles. In addition, these findings can give insight into the actual additive manufacturing process. PMID:26601040

Between and beyond additivity and non-additivity : the statistical modelling of genotype by environment interaction in plant breeding

OpenAIRE

Eeuwijk, van, F.A.

1996-01-01

In plant breeding it is a common observation to see genotypes react differently to environmental changes. This phenomenon is called genotype by environment interaction. Many statistical approaches for analysing genotype by environment interaction rely heavily on the analysis of variance model. Genotype by environment interaction is then taken to be equivalent to non-additivity. This thesis criticizes the analysis of variance approach. Modelling genotype by environment interaction by non-addit...

Development of Brassica oleracea-nigra monosomic alien addition lines: genotypic, cytological and morphological analyses.

Science.gov (United States)

Tan, Chen; Cui, Cheng; Xiang, Yi; Ge, Xianhong; Li, Zaiyun

2017-12-01

We report the development and characterization of Brassica oleracea - nigra monosomic alien addition lines (MAALs) to dissect the Brassica B genome. Brassica nigra (2n = 16, BB) represents the diploid Brassica B genome which carries many useful genes and traits for breeding but received limited studies. To dissect the B genome from B. nigra, the triploid F 1 hybrid (2n = 26, CCB) obtained previously from the cross B. oleracea var. alboglabra (2n = 18, CC) × B. nigra was used as the maternal parent and backcrossed successively to parental B. oleracea. The progenies in BC 1 to BC 3 generations were analyzed by the methods of FISH and SSR markers to screen the monosomic alien addition lines (MAALs) with each of eight different B-genome chromosomes added to C genome (2n = 19, CC + 1B 1-8 ), and seven different MAALs were established, except for the one with chromosome B2 which existed in one triple addition. Most of these MAALs were distinguishable morphologically from each other, as they expressed the characters from B. nigra differently and at variable extents. The alien chromosome remained unpaired as a univalent in 86.24% pollen mother cells at diakinesis or metaphase I, and formed a trivalent with two C-genome chromosomes in 13.76% cells. Transmission frequency of all the added chromosomes was far higher through the ovules (averagely 14.40%) than the pollen (2.64%). The B1, B4 and B5 chromosomes were transmitted by female at much higher rates (22.38-30.00%) than the other four (B3, B6, B7, B8) (5.04-8.42%). The MAALs should be valuable for exploiting the genome structure and evolution of B. nigra.

Effects of Ce, La and Ba addition on the electrochemical behavior of super duplex stainless steels

International Nuclear Information System (INIS)

Yoo, Yun-Ha; Choi, Yoon-Seok; Kim, Jung-Gu; Park, Yong-Soo

2010-01-01

The effects of rare earth metal (REM: Ce, La) and Ba addition on aqueous corrosion properties of super duplex stainless steels (SDSS) were investigated by electrochemical tests and surface analyses. The results of potentiodynamic test indicated that the passive range increased by the addition of Ce, La, and Ba, indicating increased relative resistance to localized corrosion. The EIS measurements showed that the Ce-La-Ba-bearing alloys exhibited higher R ct and R p values than the Ce-La-Ba-free alloy at the passive and breakdown states. Furthermore, the additions of REMs and Ba together promoted the formation of dense chromium-enriched passive film.

Showing/Sharing: Analysing Visual Communication from a Praxeological Perspective

Directory of Open Access Journals (Sweden)

Maria Schreiber

2017-12-01

Full Text Available This contribution proposes a methodological framework for empirical research into visual practices on social media. The framework identifies practices, pictures and platforms as relevant dimensions of analysis. It is mainly developed within, and is compatible with qualitative, interpretive approaches which focus on visual communication as part of everyday personal communicative practices. Two screenshots from Instagram and Facebook are introduced as empirical examples to investigate collaborative practices of meaning-making relating to pictures on social media. While social media seems to augment reflexive, processual practices of negotiating identities, visual media, in particular, amps up aesthetic, ambivalent and embodied dimensions within these practices.

Automated monosegmented flow analyser. Determination of glucose, creatinine and urea.

Science.gov (United States)

Raimundo Júnior, I M; Pasquini, C

1997-10-01

An automated monosegmented flow analyser containing a sampling valve and a reagent addition module and employing a laboratory-made photodiode array spectrophotometer as detection system is described. The instrument was controlled by a 386SX IBM compatible microcomputer through an IC8255 parallel port that communicates with the interface which controls the sampling valve and reagent addition module. The spectrophotometer was controlled by the same microcomputer through an RS232 serial standard interface. The software for the instrument was written in QuickBasic 4.5. Opto-switches were employed to detect the air bubbles limiting the monosegment, allowing precise sample localisation for reagent addition and signal reading. The main characteristics of the analyser are low reagent consumption and high sensitivity which is independent of the sample volume. The instrument was designed to determine glucose, creatinine or urea in blood plasma and serum without hardware modification. The results were compared against those obtained by the Clinical Hospital of UNICAMP using commercial analysers. Correlation coefficients among the methods were 0.997, 0.982 and 0.996 for glucose, creatinine and urea, respectively.

Multi-Scale Carbon Isotopic Analyses Show Allende Nanodiamonds are Mostly Solar with Some PreSolar

Science.gov (United States)

Lewis, J. B.; Isheim, D.; Floss, C.; Gyngard, F.; Seidman, D. N.

2017-07-01

NanoSIMS and atom-probe experiments on different-sized aggregates of meteoritic nanodiamonds show mostly normal C isotopes, with a fraction of 13C-enriched material. The best interpretation is a combination of solar system and supernova formation.

FY01 Supplemental Science and Performance Analyses, Volume 1: Scientific Bases and Analyses, Part 1 and 2

International Nuclear Information System (INIS)

Dobson, David

2001-01-01

The U.S. Department of Energy (DOE) is considering the possible recommendation of a site at Yucca Mountain, Nevada, for development as a geologic repository for the disposal of high-level radioactive waste and spent nuclear fuel. To facilitate public review and comment, in May 2001 the DOE released the Yucca Mountain Science and Engineering Report (S and ER) (DOE 2001 [DIRS 153849]), which presents technical information supporting the consideration of the possible site recommendation. The report summarizes the results of more than 20 years of scientific and engineering studies. A decision to recommend the site has not been made: the DOE has provided the S and ER and its supporting documents as an aid to the public in formulating comments on the possible recommendation. When the S and ER (DOE 2001 [DIRS 153849]) was released, the DOE acknowledged that technical and scientific analyses of the site were ongoing. Therefore, the DOE noted in the Federal Register Notice accompanying the report (66 FR 23 013 [DIRS 155009], p. 2) that additional technical information would be released before the dates, locations, and times for public hearings on the possible recommendation were announced. This information includes: (1) the results of additional technical studies of a potential repository at Yucca Mountain, contained in this FY01 Supplemental Science and Performance Analyses: Vol. 1, Scientific Bases and Analyses; and FY01 Supplemental Science and Performance Analyses: Vol. 2, Performance Analyses (McNeish 2001 [DIRS 155023]) (collectively referred to as the SSPA) and (2) a preliminary evaluation of the Yucca Mountain site's preclosure and postclosure performance against the DOE's proposed site suitability guidelines (10 CFR Part 963 [64 FR 67054] [DIRS 124754]). By making the large amount of information developed on Yucca Mountain available in stages, the DOE intends to provide the public and interested parties with time to review the available materials and to formulate

Three WRKY transcription factors additively repress abscisic acid and gibberellin signaling in aleurone cells.

Science.gov (United States)

Zhang, Liyuan; Gu, Lingkun; Ringler, Patricia; Smith, Stanley; Rushton, Paul J; Shen, Qingxi J

2015-07-01

Members of the WRKY transcription factor superfamily are essential for the regulation of many plant pathways. Functional redundancy due to duplications of WRKY transcription factors, however, complicates genetic analysis by allowing single-mutant plants to maintain wild-type phenotypes. Our analyses indicate that three group I WRKY genes, OsWRKY24, -53, and -70, act in a partially redundant manner. All three showed characteristics of typical WRKY transcription factors: each localized to nuclei and yeast one-hybrid assays indicated that they all bind to W-boxes, including those present in their own promoters. Quantitative real time-PCR (qRT-PCR) analyses indicated that the expression levels of the three WRKY genes varied in the different tissues tested. Particle bombardment-mediated transient expression analyses indicated that all three genes repress the GA and ABA signaling in a dosage-dependent manner. Combination of all three WRKY genes showed additive antagonism of ABA and GA signaling. These results suggest that these WRKY proteins function as negative transcriptional regulators of GA and ABA signaling. However, different combinations of these WRKY genes can lead to varied strengths in suppression of their targets. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

Publication bias in dermatology systematic reviews and meta-analyses.

Science.gov (United States)

Atakpo, Paul; Vassar, Matt

2016-05-01

Systematic reviews and meta-analyses in dermatology provide high-level evidence for clinicians and policy makers that influence clinical decision making and treatment guidelines. One methodological problem with systematic reviews is the under representation of unpublished studies. This problem is due in part to publication bias. Omission of statistically non-significant data from meta-analyses may result in overestimation of treatment effect sizes which may lead to clinical consequences. Our goal was to assess whether systematic reviewers in dermatology evaluate and report publication bias. Further, we wanted to conduct our own evaluation of publication bias on meta-analyses that failed to do so. Our study considered systematic reviews and meta-analyses from ten dermatology journals from 2006 to 2016. A PubMed search was conducted, and all full-text articles that met our inclusion criteria were retrieved and coded by the primary author. 293 articles were included in our analysis. Additionally, we formally evaluated publication bias in meta-analyses that failed to do so using trim and fill and cumulative meta-analysis by precision methods. Publication bias was mentioned in 107 articles (36.5%) and was formally evaluated in 64 articles (21.8%). Visual inspection of a funnel plot was the most common method of evaluating publication bias. Publication bias was present in 45 articles (15.3%), not present in 57 articles (19.5%) and not determined in 191 articles (65.2%). Using the trim and fill method, 7 meta-analyses (33.33%) showed evidence of publication bias. Although the trim and fill method only found evidence of publication bias in 7 meta-analyses, the cumulative meta-analysis by precision method found evidence of publication bias in 15 meta-analyses (71.4%). Many of the reviews in our study did not mention or evaluate publication bias. Further, of the 42 articles that stated following PRISMA reporting guidelines, 19 (45.2%) evaluated for publication bias. In

INFLUENCE OF NATURAL ADDITIVES ON PROTEIN COMPLEX OF BREAD

Directory of Open Access Journals (Sweden)

Dana Urminská

2010-11-01

Full Text Available The study focuses on researching the influence of natural additives on certain technological characteristics of mixtures used for bread production, more particularly the influence of N substances in used raw material on selected qualitative parameters of bread. The blends for bread production to be analysed were prepared by mixing wheat flour with an addition of oat, buckwheat, lentil and chickpea wholegrain flour in different portions (10, 20, 30, 40 and 50 %. The experiment showed that the addition of natural additives worsened the protein complex of the blends used in bread production (worsening also qualitative parameters known as product volume. The loaves prepared with an addition of buckwheat, oat, lentil and chickpea were evaluated to be of a lesser quality from a technological viewpoint when compared with pure wheat loaves. The lower content of gluten forming proteins and the generally changed protein composition of blends due to additives caused a lower percentage of wet gluten content, its lower extensibility and swelling capacity. The sedimentation value (Zeleny index decreased proportionally with the increase of addition until the level was unsatisfactory for raw material intended for bakery purposes. The N content in experimental loaves was higher than in the reference loaves and it increased according to the selected additive and its portion in the blend (more with the addition of lentil and chickpea, less in case of buckwheat and oat which is considered as positive from a nutritional point of view. But from the technological point of view the additives did not show any positive influence and caused a lower loaf bread volume. The most significant decrease of the loaf bread volume was found with the addition of 50 % of buckwheat (- 45.6 %. Better results were obtained with a lower portion of the additive: loaf with an addition of 30 % of chickpea (volume decreased by 12.8 % > loaf with an addition of 30 % of lentil (volume

First-born siblings show better second language skills than later born siblings

Science.gov (United States)

Keller, Karin; Troesch, Larissa M.; Grob, Alexander

2015-01-01

We examined the extent to which three sibling structure variables number of siblings, birth order, and presence of an older sibling at school age are linked to the second language skills of bilingual children. The research questions were tested using an ethnically heterogeneous sample of 1209 bilingual children with German as a second language. Controlling for children’s age, sex, nationality, number of children’s books at home, family language and parental German language skills, hierarchical regression analyses showed an inverse relationship between the number of siblings and second language skills: the more siblings a child had, the lower was his/her second language proficiency. This relationship was mediated by attendance in early education institutions. Moreover, first-born siblings showed better second language skills than later born siblings. The current study revealed that the resource dilution model, i.e., the decrease in resources for every additional sibling, holds for second language acquisition. Moreover, the results indicate that bilingual children from families with several children benefit from access to early education institutions. PMID:26089806

First-born siblings show better second language skills than later born siblings

Directory of Open Access Journals (Sweden)

Karin eKeller

2015-06-01

Full Text Available We examined the extent to which three sibling structure variables number of siblings, birth order and presence of an older sibling at school age are linked to the second language skills of bilingual children. The research questions were tested using an ethnically heterogeneous sample of 1209 bilingual children with German as a second language. Controlling for children’s age, sex, nationality, number of children’s books at home, family language and parental German language skills, hierarchical regression analyses showed an inverse relationship between the number of siblings and second language skills: The more siblings a child had, the lower was his/her second language proficiency. This relationship was mediated by attendance in early education institutions. Moreover, first-born siblings showed better second language skills than later born siblings.The current study revealed that the resource dilution model, i.e., the decrease in resources for every additional sibling, holds for second language acquisition. Moreover, the results indicate that bilingual children from families with several children benefit from access to early education institutions.

Romanian Consumers’ Willingness to Buy Foodstuffs Containing Food Additives: Results of a Conjoint Study

Directory of Open Access Journals (Sweden)

Viktória Szucs

2015-11-01

Full Text Available Results of the literature and the authors’ previous studies showed consumers’ high anxiety regarding food additives as well as their high demand for additive-free products in Romania, even at higher prices. Hence, the aim of our work was to analyse the willingness to buy and preference of foodstuffs containing natural and artificial food additives in Romania.A complex conjoint analysis (rating-based and choice-based was performed amongst Romanian consumers. Conjoint cards were created from two groups of food additives (‘preservatives’ and ‘packaging gases’, and consisting of two ‘model foodstuffs’ (pre-packed sliced cheese and chips. For the study, three factors were selected: ‘preservatives’ (artificial/natural, ‘packaging gases’ (contains/does not contain and ‘price’ (average+10%/average+20%. Results were collected via the internet and data were analysed with the help of SPSS Conjoint and XLSTAT softwares. ‘Preservatives’ have a dominant importance and ‘natural preservatives’ have a high utility in shopping decisions. ‘Natural’ compounds have higher importance in the example of foodstuffs thought to contain less food additives (pre-packed sliced cheese, while the presence of ‘packaging gases’ is acceptable to respondents in easy to handle and convenient foodstuffs. With the help of the cluster analysis, the promising target group (‘desire for natural’ characterising additive-free foodstuffs  that contain natural compounds was identified. Restricted comparison of the rating-based and the choice-based analysis showed that the choice-based method was easier to handle and understand for the participants. Regarding the results, a threefold conclusion was established: the ‘prominence effect’ is greater for the choice-based than the rating-based analysis; the effect of ‘level focusing’ is smaller in the rating-based than in the choice-based analysis; the ‘compatibility effect’ the rating

BIOMETRICAL ANALYSIS OF ARABIAN FOALS AND THEIR LATER SUCCESSES IN SHOWS AND ON RACE TRACK

Directory of Open Access Journals (Sweden)

M. PIESZKA

2007-10-01

Full Text Available Arabian horses are one of the most important products of Polish horse breeding.Many of them are International and World champions in shows; others are very wellknown as courageous race horses. To obtain such champions it is necessary to takeunder consideration many factors affecting the final results. The objective of thisstudy was to evaluate the effect of biometrical measurements of the foals at birthaccording to their future successes in shows and on racetrack. The study was carriedout on 143 horses winning in shows and in races. Body weight, height at withers,girth and canon circumferences taken at birth of these horses were analysed.Additionally coat colour was studied. All studied animals were divided into threegroups according to each measurement and the differences between such groupswere evaluated according points obtained for particular place at shows and place inraces. It was stated that horses heavier at birth and with higher girth circumferencegot more successes both at shows and on racetrack. Horses with higher height atwithers at birth were more successful in shows while animals with higher canoncircumference won oftener at race track. It was observed that the most courageousrace horses were bay while most champions were grey.

Radiation physics and shielding codes and analyses applied to design-assist and safety analyses of CANDUR and ACRTM reactors

International Nuclear Information System (INIS)

Aydogdu, K.; Boss, C. R.

2006-01-01

This paper discusses the radiation physics and shielding codes and analyses applied in the design of CANDU and ACR reactors. The focus is on the types of analyses undertaken rather than the inputs supplied to the engineering disciplines. Nevertheless, the discussion does show how these analyses contribute to the engineering design. Analyses in radiation physics and shielding can be categorized as either design-assist or safety and licensing (accident) analyses. Many of the analyses undertaken are designated 'design-assist' where the analyses are used to generate recommendations that directly influence plant design. These recommendations are directed at mitigating or reducing the radiation hazard of the nuclear power plant with engineered systems and components. Thus the analyses serve a primary safety function by ensuring the plant can be operated with acceptable radiation hazards to the workers and public. In addition to this role of design assist, radiation physics and shielding codes are also deployed in safety and licensing assessments of the consequences of radioactive releases of gaseous and liquid effluents during normal operation and gaseous effluents following accidents. In the latter category, the final consequences of accident sequences, expressed in terms of radiation dose to members of the public, and inputs to accident analysis, e.g., decay heat in fuel following a loss-of-coolant accident, are also calculated. Another role of the analyses is to demonstrate that the design of the plant satisfies the principle of ALARA (as low as reasonably achievable) radiation doses. This principle is applied throughout the design process to minimize worker and public doses. The principle of ALARA is an inherent part of all design-assist recommendations and safety and licensing assessments. The main focus of an ALARA exercise at the design stage is to minimize the radiation hazards at the source. This exploits material selection and impurity specifications and relies

Show Horse Welfare: Horse Show Competitors' Understanding, Awareness, and Perceptions of Equine Welfare.

Science.gov (United States)

Voigt, Melissa A; Hiney, Kristina; Richardson, Jennifer C; Waite, Karen; Borron, Abigail; Brady, Colleen M

2016-01-01

The purpose of this study was to gain a better understanding of stock-type horse show competitors' understanding of welfare and level of concern for stock-type show horses' welfare. Data were collected through an online questionnaire that included questions relating to (a) interest and general understanding of horse welfare, (b) welfare concerns of the horse show industry and specifically the stock-type horse show industry, (c) decision-making influences, and (d) level of empathic characteristics. The majority of respondents indicated they agree or strongly agree that physical metrics should be a factor when assessing horse welfare, while fewer agreed that behavioral and mental metrics should be a factor. Respondent empathy levels were moderate to high and were positively correlated with the belief that mental and behavioral metrics should be a factor in assessing horse welfare. Respondents indicated the inhumane practices that most often occur at stock-type shows include excessive jerking on reins, excessive spurring, and induced excessive unnatural movement. Additionally, respondents indicated association rules, hired trainers, and hired riding instructors are the most influential regarding the decisions they make related to their horses' care and treatment.

CFD analyses of coolant channel flowfields

Science.gov (United States)

Yagley, Jennifer A.; Feng, Jinzhang; Merkle, Charles L.

1993-01-01

The flowfield characteristics in rocket engine coolant channels are analyzed by means of a numerical model. The channels are characterized by large length to diameter ratios, high Reynolds numbers, and asymmetrical heating. At representative flow conditions, the channel length is approximately twice the hydraulic entrance length so that fully developed conditions would be reached for a constant property fluid. For the supercritical hydrogen that is used as the coolant, the strong property variations create significant secondary flows in the cross-plane which have a major influence on the flow and the resulting heat transfer. Comparison of constant and variable property solutions show substantial differences. In addition, the property variations prevent fully developed flow. The density variation accelerates the fluid in the channels increasing the pressure drop without an accompanying increase in heat flux. Analyses of the inlet configuration suggest that side entry from a manifold can affect the development of the velocity profile because of vortices generated as the flow enters the channel. Current work is focused on studying the effects of channel bifurcation on the flow field and the heat transfer characteristics.

Experimental and Computational Modal Analyses for Launch Vehicle Models considering Liquid Propellant and Flange Joints

Directory of Open Access Journals (Sweden)

Chang-Hoon Sim

2018-01-01

Full Text Available In this research, modal tests and analyses are performed for a simplified and scaled first-stage model of a space launch vehicle using liquid propellant. This study aims to establish finite element modeling techniques for computational modal analyses by considering the liquid propellant and flange joints of launch vehicles. The modal tests measure the natural frequencies and mode shapes in the first and second lateral bending modes. As the liquid filling ratio increases, the measured frequencies decrease. In addition, as the number of flange joints increases, the measured natural frequencies increase. Computational modal analyses using the finite element method are conducted. The liquid is modeled by the virtual mass method, and the flange joints are modeled using one-dimensional spring elements along with the node-to-node connection. Comparison of the modal test results and predicted natural frequencies shows good or moderate agreement. The correlation between the modal tests and analyses establishes finite element modeling techniques for modeling the liquid propellant and flange joints of space launch vehicles.

Approximate analyses of inelastic effects in pipework

International Nuclear Information System (INIS)

Jobson, D.A.

1983-01-01

This presentation shows figures concerned with analyses of inelastic effects in pipework as follows: comparison of experimental and calculated simplified analyses results for free end rotation and for circumferential strain; interrupted stress relaxation; regenerated relaxation caused by reversed yield; buckling of straight pipe under combined bending and torsion; results of fatigues test of pipe bend

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

Comparative analyses of microbial structures and gene copy numbers in the anaerobic digestion of various types of sewage sludge.

Science.gov (United States)

Hidaka, Taira; Tsushima, Ikuo; Tsumori, Jun

2018-04-01

Anaerobic co-digestion of various sewage sludges is a promising approach for greater recovery of energy, but the process is more complicated than mono-digestion of sewage sludge. The applicability of microbial structure analyses and gene quantification to understand microbial conditions was evaluated. The results show that information from gene analyses is useful in managing anaerobic co-digestion and damaged microbes in addition to conventional parameters like total solids, pH and biogas production. Total bacterial 16S rRNA gene copy numbers are the most useful tools for evaluating unstable anaerobic digestion of sewage sludge, rather than mcrA and total archaeal 16S rRNA gene copy numbers, and high-throughput sequencing. First order decay rates of gene copy numbers during pH failure were higher than typical decay rates of microbes in stable operation. The sequencing analyses, including multidimensional scaling, showed very different microbial structure shifts, but the results were not consistent. Copyright © 2017 Elsevier Ltd. All rights reserved.

Status on DEMO Helium Cooled Lithium Lead breeding blanket thermo-mechanical analyses

Energy Technology Data Exchange (ETDEWEB)

Aubert, J., E-mail: julien.aubert@cea.fr [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France); Aiello, G.; Jaboulay, J.-C. [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France); Kiss, B. [Institute of Nuclear Techniques, Budapest University of Technology and Economics, Budapest (Hungary); Morin, A. [CEA-Saclay, DEN, DM2S, F-91191 Gif-sur-Yvette (France)

2016-11-01

the equatorial outboard module has been analyzed with CAST3M in case of accident, according to RCC-MRx, resulting in relatively good behavior of the box. Additionally analyses have been performed in order to check the good behavior of the tie rods modules’ attachments system in normal condition showing promising results.

Analysing and Comparing Encodability Criteria

Directory of Open Access Journals (Sweden)

Kirstin Peters

2015-08-01

Full Text Available Encodings or the proof of their absence are the main way to compare process calculi. To analyse the quality of encodings and to rule out trivial or meaningless encodings, they are augmented with quality criteria. There exists a bunch of different criteria and different variants of criteria in order to reason in different settings. This leads to incomparable results. Moreover it is not always clear whether the criteria used to obtain a result in a particular setting do indeed fit to this setting. We show how to formally reason about and compare encodability criteria by mapping them on requirements on a relation between source and target terms that is induced by the encoding function. In particular we analyse the common criteria full abstraction, operational correspondence, divergence reflection, success sensitiveness, and respect of barbs; e.g. we analyse the exact nature of the simulation relation (coupled simulation versus bisimulation that is induced by different variants of operational correspondence. This way we reduce the problem of analysing or comparing encodability criteria to the better understood problem of comparing relations on processes.

Electron microscopy analyses and electrical properties of the layered Bi2WO6 phase

International Nuclear Information System (INIS)

Taoufyq, A.; Ait Ahsaine, H.; Patout, L.; Benlhachemi, A.; Ezahri, M.

2013-01-01

The bismuth tungstate Bi 2 WO 6 was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2 1 non centrosymmetric space group previously proposed for this phase. The layers Bi 2 O 2 2+ and WO 4 2− have been directly evidenced from the HRTEM images. The electrical properties of Bi 2 WO 6 compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi 2 WO 6 phase, with a representation of the cell dimensions (b and c vectors). The Bi 2 O 2 2+ and WO 4 2− sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi 2 WO 6 . • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification

Microcomputer-controlled thermoluminescent analyser IJS MR-200

International Nuclear Information System (INIS)

Mihelic, M.; Miklavzic, U.; Rupnik, Z.; Satalic, P.; Spreizer, F.; Zerovnik, I.

1985-01-01

Performances and concept of the multipurpose, microcomputer-controlled thermoluminescent analyser, designed for use in laboratory work TL dosemeters as well as for routine dose readings in the range from ecological to accident doses is described. The main features of the analyser are: time-linear sampling, digitalisation, storing, and subsequent displaying on the monitor time scale of the glow and and temperature curve of the TL material; digital stabilization, control and diagnostic of the analog unit; ability of storing 7 different 8-parametric heating programs; ability of storing 15 evaluation programs defined by 2 or 4 parameters and 3 different algorithms (altogether 5 types of evaluations). Analyser has several features intended for routine work: 9 function keys and possibilities of file forming on cassette or display disc, of dose calculation and averaging, of printing reports with names, and possibility of additional programming in Basic. (author)

Reprocessing of spent nuclear fuel, Annex 3: Chemical and radiometric control analyses

International Nuclear Information System (INIS)

Gal, I.

1964-01-01

Simple, fast and reliable control analyses are obligatory during reprocessing. The analyses performed covered measuring the contents of uranium in water and organic solutions, contents of plutonium in water and organic solutions as well as the free acid in both solutions. In addition temporary analyses were done to determine the density of water and organic solutions as well as content of TBP in kerosine

Molecular cytogenetic analyses of Epinephelus bruneus and Epinephelus moara (Perciformes, Epinephelidae

Directory of Open Access Journals (Sweden)

Minglan Guo

2014-06-01

Full Text Available Genus Epinephelus (Perciformes, Epinephelidae, commonly known as groupers, are usually difficult in species identification for the lack and/or change of morphological specialization. In this study, molecular cytogenetic analyses were firstly performed to identify the closely related species Epinephelus bruneus and E. moara in this genus. The species-specific differences of both fish species showed in karyotype, chromosomal distribution of nucleolar organizer regions (NORs and localization of 18S rDNA. The heterochromatin (interstitial C-bands and distribution pattern of telomere (TTAGGGn in E. bruneus revealed the chromosomal rearrangements and different karyotypic evolutionary characteristics compared to those in E. moara. The cytogenetic data suggested that the lineages of E. bruneus and E. moara were recently derived within the genus Epinephelus, and E. moara exhibited more plesiomorphic features than E. bruneus. All results confirmed that E. moara, which has long been considered a synonym of E. bruneus, is a distinct species in the family Epinephelidae. In addition, molecular cytogenetic analyses are useful in species differentiation and phylogenetic reconstruction in groupers.

Tomographic local 2D analyses of the WISExSuperCOSMOS all-sky galaxy catalogue

Science.gov (United States)

Novaes, C. P.; Bernui, A.; Xavier, H. S.; Marques, G. A.

2018-05-01

The recent progress in obtaining larger and deeper galaxy catalogues is of fundamental importance for cosmological studies, especially to robustly measure the large scale density fluctuations in the Universe. The present work uses the Minkowski Functionals (MF) to probe the galaxy density field from the WISExSuperCOSMOS (WSC) all-sky catalogue by performing tomographic local analyses in five redshift shells (of thickness δz = 0.05) in the total range of 0.10 methodology reveals 1 - 3 regions of the GNC maps in each redshift shell with an uncommon behaviour (extreme regions), i.e., p-value < 1.4%. Indeed, the resulting MF curves show signatures that suggest the uncommon behaviour to be associated with the presence of over- or under-densities there, but contamination due to residual foregrounds is not discarded. Additionally, even though our analyses indicate a good agreement among data and simulations, we identify 1 highly extreme region, seemingly associated to a large clustered distribution of galaxies. Our results confirm the usefulness of the MF to analyse GNC maps from photometric galaxy datasets.

14C-carbaril metabolism in soils modified by organic matter oxidation and addition of glucose

International Nuclear Information System (INIS)

Hirata, R.; Ruegg, E.F.

1984-01-01

Carbaril behaviour is studied in samples of Brunizen and Dark Red Latosol soils from Parana, using radiometric techniques, with the objective of determining the role of oxidation fo its organic components, and enrichment with glucose, in the metabolism of the insecticide. Lots of autoclaved soils, oxidized and with no previous treatment, with and without glucose addition, are incubated with 14 C-carbaril and analysed during eight weeks. Its was noted that, as a result of oxidation both soils showed a marked improvement in the metabolism of the agrochemical while addition of glucose exerted litlle influence on the degrading processes. Three metabolites were detected with R sub(f) 0.23, 0.40 and 0.70. (Author) [pt

Kaolinite flocculation induced by smectite addition - a transmission X-ray microscopic study.

Science.gov (United States)

Zbik, Marek S; Song, Yen-Fang; Frost, Ray L

2010-09-01

The influence of smectite addition on kaolinite suspensions in water was investigated by transmission X-ray microscopy (TXM) and Scanning Electron Microscopy (SEM). Sedimentation test screening was also conducted. Micrographs were processed by the STatistic IMage Analysing (STIMAN) program and structural parameters were calculated. From the results of the sedimentation tests important influences of small smectite additions to about 3wt.% on kaolinite suspension flocculation has been found. In order to determine the reason for this smectite impact on kaolinite suspension, macroscopic behaviour micro-structural examination using Transmission X-ray Microscope (TXM) and SEM has been undertaken. TXM & SEM micrographs of freeze-dried kaolinite-smectite suspensions with up to 20% smectite showed a high degree of orientation of the fabric made of highly oriented particles and greatest density when 3wt.% of smectite was added to the 10wt.% dense kaolinite suspension. In contrast, suspensions containing pure kaolinite do not show such platelet mutual orientation but homogenous network of randomly oriented kaolinite platelets. This suggests that in kaolinite-smectite suspensions, smectite forms highly oriented basic framework into which kaolinite platelets may bond in face to face preferential contacts strengthening structure and allowing them to show plastic behaviour which is cause of platelets orientation. Copyright 2010 Elsevier Inc. All rights reserved.

The effect of hyaluronic acid addition on the properties of smoked homogenised sausages.

Science.gov (United States)

Zając, Marzena; Kulawik, Piotr; Tkaczewska, Joanna; Migdał, Władysław; Filipczak-Fiutak, Magda; Fiutak, Grzegorz

2017-06-01

This research studied the possibility of using hyaluronic acid (HA) as a food additive for meat emulsions to create a novel functional food with improved rheological and water binding properties. Sausages with 200 and 500 g kg -1 water addition were supplemented with 0, 0.01, 0.05 and 0.1 g kg -1 of HA and stored for 14 days in vacuum. Rheology, texture, weight losses, proximate composition and microbiological analyses were performed together with the sensory evaluation of produced sausages. Surprisingly, the results show that the addition of 0.05 and 0.1 g kg -1 HA reduced yield and the stability of meat emulsion by causing water outflow from the product and decreased the sensory scores of the produced sausages. The sausage with 500 g kg -1 water and 0.01 g kg -1 HA addition was the only economically viable option for introducing the product on the market. HA has a potential of being a perfect functional food additive for meat industry, although further research regarding processing conditions should be performed. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

CFD simulation of rotor aerodynamic performance when using additional surface structure array

Science.gov (United States)

Wang, Bing; Kong, Deyi

2017-10-01

The present work analyses the aerodynamic performance of the rotor with additional surface structure array in an attempt to maximize its performance in hover flight. The unstructured grids and the Reynolds Average Navier-Stokes equations were used to calculate the performance of the prototype rotor and the rotor with additional surface structure array in the air. The computational fluid dynamics software FLUENT was used to simulate the thrust of the rotors. The results of the calculations are in reasonable agreement with experimental data, which shows that the calculation model used in this work is useful in simulating the performance of the rotor with additional surface structure array. With this theoretical calculation model, the thrusts of the rotors with arrays of surface structure in three different shapes were calculated. According to the simulation results and the experimental data, the rotor with triangle surface structure array has better aerodynamic performance than the other rotors. In contrast with the prototype rotor, the thrust of the rotor with triangle surface structure array increases by 5.2% at the operating rotating speed of 3000r/min, and the additional triangle surface structure array has almost no influence on the efficiency of the rotor.

Thermal and stress analyses of meltdown cups for LMFBR safety experiments using SLSF in-reactor loops

International Nuclear Information System (INIS)

Blomquist, C.A.; Pierce, R.D.; Pedersen, D.R.; Ariman, T.

1977-01-01

The test trains for the Sodium Loop Safety Facility (SLSF) in-reactor experiments, which simulate hypothetical LMFBR accidents, have a meltdown cup to protect the primary containment from the effects of molten materials. Thermal and stress analyses were performed on the cup which is designed to contain 3.6 kg of molten fuel and 2.4 kg of molten steel. Thermal analyses were performed with the Argonne-modified version fo the general heat transfer code THTB, based on the instantaneous addition of 3200 0 K molten fuel with a decay heat of 9 W/gm and 1920 0 K molten steel. These analyses have shown that the cup will adequately cool the molten materials. The stress analysis showed that the Inconel vessel would not fail from the pressure loading, it was also shown that brittle fracture of the tungsten liner from thermal gradients is unlikely. Therefore, the melt-down cup meets the structural design requirements. (Auth.)

The Presentation of Animals in English as an Additional Language Coursebooks

Science.gov (United States)

Jacobs, George M.; Jiexin, Teh; Michael, Joyce J.

2016-01-01

Education materials can be analysed in many ways. The current study analysed EAL (English as an Additional Language) coursebooks as to the presentation of nonhuman animals in the books. The study examined 22 EAL coursebooks. The research looked at the percentage of activities that contained animals in the coursebooks, what types of animals were…

HLA region excluded by linkage analyses of early onset periodontitis

Energy Technology Data Exchange (ETDEWEB)

Sun, C.; Wang, S.; Lopez, N.

1994-09-01

Previous studies suggested that HLA genes may influence susceptibility to early-onset periodontitis (EOP). Segregation analyses indicate that EOP may be due to a single major gene. We conducted linkage analyses to assess possible HLA effects on EOP. Fifty families with two or more close relatives affected by EOP were ascertained in Virginia and Chile. A microsatellite polymorphism within the HLA region (at the tumor necrosis factor beta locus) was typed using PCR. Linkage analyses used a donimant model most strongly supported by previous studies. Assuming locus homogeneity, our results exclude a susceptibility gene within 10 cM on either side of our marker locus. This encompasses all of the HLA region. Analyses assuming alternative models gave qualitatively similar results. Allowing for locus heterogeneity, our data still provide no support for HLA-region involvement. However, our data do not statistically exclude (LOD <-2.0) hypotheses of disease-locus heterogeneity, including models where up to half of our families could contain an EOP disease gene located in the HLA region. This is due to the limited power of even our relatively large collection of families and the inherent difficulties of mapping genes for disorders that have complex and heterogeneous etiologies. Additional statistical analyses, recruitment of families, and typing of flanking DNA markers are planned to more conclusively address these issues with respect to the HLA region and other candidate locations in the human genome. Additional results for markers covering most of the human genome will also be presented.

We're Playing "Jeremy Kyle"! Television Talk Shows in the Playground

Science.gov (United States)

Marsh, Jackie; Bishop, Julia

2014-01-01

This paper focuses on an episode of play in a primary school playground in England, which featured a group of children re-enacting elements of the television talk show "The Jeremy Kyle Show". The episode is analysed in the light of work that has identified the key elements of the talk show genre and the children's play is examined in…

Effect of silver addition on the properties of combustion synthesized nanocrystalline LiCoO2

International Nuclear Information System (INIS)

Ghosh, Paromita; Mahanty, S.; Basu, R.N.

2008-01-01

Nanocrystalline (∼50 nm) LiCoO 2 powders containing 0-10 mol% of Ag have been prepared by combustion synthesis using citrate-nitrate combustion route. Thermal analyses show a sharp decomposition of the gel at ∼177 deg. C for pristine LiCoO 2 . With addition of silver, the decomposition becomes sluggish and it completes only above 430 deg. C. X-ray powder diffraction analyses show an increase in lattice parameter, c, with increasing Ag content suggesting the occupation of Ag within LiCoO 2 interlayer spacings. Transmission electron microscopy indicates diffusion of Ag into LiCoO 2 grains. It has been observed that adding 1.0 mol% silver increases the room temperature electrical conductivity by more than two orders of magnitude (1.5 x 10 -3 S cm -1 ). Galvanostatic charge-discharge profiles of coin cells fabricated with the synthesized powders show a two-fold enhancement in the discharge capacity for 1.0 mol% Ag-added LiCoO 2 cathode (140 mAh g -1 ) compared to that for pristine LiCoO 2 (70 mAh g -1 )

Twenty years of meta-analyses in orthopaedic surgery: has quality kept up with quantity?

Science.gov (United States)

Dijkman, Bernadette G; Abouali, Jihad A K; Kooistra, Bauke W; Conter, Henry J; Poolman, Rudolf W; Kulkarni, Abhaya V; Tornetta, Paul; Bhandari, Mohit

2010-01-01

As the number of studies in the literature is increasing, orthopaedic surgeons highly depend on meta-analyses as their primary source of scientific evidence. The objectives of this review were to assess the scientific quality and number of published meta-analyses on orthopaedics-related topics over time. We conducted, in duplicate and independently, a systematic review of published meta-analyses in orthopaedics in the years 2005 and 2008 and compared them with a previous systematic review of meta-analyses from 1969 to 1999. A search of electronic databases (MEDLINE, EMBASE, and the Cochrane Database of Systematic Reviews) was performed to identify meta-analyses published in 2005 and 2008. We searched bibliographies and contacted content experts to identify additional relevant studies. Two investigators independently assessed the quality of the studies, using the Oxman and Guyatt index, and abstracted relevant data. We included forty-five and forty-four meta-analyses from 2005 and 2008, respectively. While the number of meta-analyses increased fivefold from 1999 to 2008, the mean quality score did not change significantly over time (p = 0.067). In the later years, a significantly lower proportion of meta-analyses had methodological flaws (56% in 2005 and 68% in 2008) compared with meta-analyses published prior to 2000 (88%) (p = 0.006). In 2005 and 2008, respectively, 18% and 30% of the meta-analyses had major to extensive flaws in their methodology. Studies from 2008 with positive conclusions used and described appropriate criteria for the validity assessment less often than did those with negative results. The use of random-effects and fixed-effects models as pooling methods became more popular toward 2008. Although the methodological quality of orthopaedic meta-analyses has increased in the past twenty years, a substantial proportion continues to show major to extensive flaws. As the number of published meta-analyses is increasing, a routine checklist for

Outcomes of sequential treatment with sorafenib followed by regorafenib for HCC: additional analyses from the phase 3 RESORCE trial.

Science.gov (United States)

Finn, Richard S; Merle, Philippe; Granito, Alessandro; Huang, Yi-Hsiang; Bodoky, György; Pracht, Marc; Yokosuka, Osamu; Rosmorduc, Olivier; Gerolami, René; Caparello, Chiara; Cabrera, Roniel; Chang, Charissa; Sun, Weijing; LeBerre, Marie-Aude; Baumhauer, Annette; Meinhardt, Gerold; Bruix, Jordi

2018-04-25

The RESORCE trial showed that regorafenib improves overall survival (OS) in patients with hepatocellular carcinoma progressing during sorafenib treatment (hazard ratio [HR] 0.62, 95% confidence interval [CI] 0.50, 0.78; P<.0001). This exploratory analysis describes outcomes of sequential treatment with sorafenib followed by regorafenib. In RESORCE, 573 patients were randomized 2:1 to regorafenib 160mg/day or placebo for 3 weeks on/1 week off. Efficacy and safety were evaluated by last sorafenib dose. The time from the start of sorafenib to death was assessed. Time to progression (TTP) in RESORCE was analyzed by TTP during prior sorafenib treatment. HRs (regorafenib/placebo) for OS by last sorafenib dose were similar (0.67 for 800 mg/day; 0.68 for <800 mg/day). Rates of grade 3, 4, and 5 adverse events with regorafenib by last sorafenib dose (800 mg/day versus <800 mg/day) were 52%, 11%, and 15% versus 60%, 10%, and 12%, respectively. Median times (95% CI) from the start of sorafenib to death were 26.0 months (22.6, 28.1) for regorafenib and 19.2 months (16.3, 22.8) for placebo. Median time from the start of sorafenib to progression on sorafenib was 7.2 months for the regorafenib arm and 7.1 months for the placebo arm. An analysis of TTP in RESORCE in subgroups defined by TTP during prior sorafenib in quartiles (Q) showed HRs (regorafenib/placebo; 95% CI) of 0.66 (0.45, 0.96; Q1); 0.26 (0.17, 0.40; Q2); 0.40 (0.27, 0.60; Q3); and 0.54 (0.36, 0.81; Q4). These exploratory analyses show that regorafenib conferred a clinical benefit regardless of the last sorafenib dose or TTP on prior sorafenib. Rates of adverse events were generally similar regardless of the last sorafenib dose. This analysis examined characteristics and outcomes of patients with HCC who were treated with regorafenib after they had disease progression during sorafenib treatment. Regorafenib provided clinical benefit to patients regardless of the pace of their disease progression during prior sorafenib

Feed addition of curcumin to laying hens showed anticoccidial effect, and improved egg quality and animal health.

Science.gov (United States)

Galli, Gabriela M; Da Silva, Aleksandro S; Biazus, Angelisa H; Reis, João H; Boiago, Marcel M; Topazio, Josué P; Migliorini, Marcos J; Guarda, Naiara S; Moresco, Rafael N; Ourique, Aline F; Santos, Cayane G; Lopes, Leandro S; Baldissera, Matheus D; Stefani, Lenita M

2018-01-31

The aim of this study was to evaluate whether the addition of curcumin in the diet of commercial laying hens could have an anticoccidial action and improve egg quality. For this, 60 laying hens were divided into three groups: T0 (the control group); T30 and T50 (30 and 50 mg/kg of curcumin in the feed, respectively). Eggs recently laid were collected on days 14 and 21 of the experiment, and stored for 21 days. It was observed increased specific gravity and yolk index in stored eggs of the groups T30 and T50 compared to T0. The yolk color reduced in the eggs stored from groups T30 and T50 compared to T0. Moreover, TBARS levels were lower in fresh and stored eggs from groups T30 and T50. It was observed increased TAC levels in fresh eggs from groups T30 and T50 and in stored eggs from the group T50. The presence of curcumin was not detected by HPLC in the yolk and albumen. Seric levels of albumin and uric acid did not differ between groups, while seric levels of total proteins increased on day 21 on groups T30 and T50. Finally, it was observed a significant reduction on the number of oocysts in fecal samples on days 14 and 21 of T30 and T50 compared to T0. Based on these evidences, it is possible to conclude that the addition of curcumin in the diet of laying hens has an anticoccidial effect and improves egg quality. Copyright © 2018 Elsevier Ltd. All rights reserved.

GIS-based Approaches to Catchment Area Analyses of Mass Transit

DEFF Research Database (Denmark)

Andersen, Jonas Lohmann Elkjær; Landex, Alex

2009-01-01

Catchment area analyses of stops or stations are used to investigate potential number of travelers to public transportation. These analyses are considered a strong decision tool in the planning process of mass transit especially railroads. Catchment area analyses are GIS-based buffer and overlay...... analyses with different approaches depending on the desired level of detail. A simple but straightforward approach to implement is the Circular Buffer Approach where catchment areas are circular. A more detailed approach is the Service Area Approach where catchment areas are determined by a street network...... search to simulate the actual walking distances. A refinement of the Service Area Approach is to implement additional time resistance in the network search to simulate obstacles in the walking environment. This paper reviews and compares the different GIS-based catchment area approaches, their level...

Understanding the Flow Physics of Shock Boundary-Layer Interactions Using CFD and Numerical Analyses

Science.gov (United States)

Friedlander, David J.

2013-01-01

Computational fluid dynamic (CFD) analyses of the University of Michigan (UM) Shock/Boundary-Layer Interaction (SBLI) experiments were performed as an extension of the CFD SBLI Workshop held at the 48th AIAA Aerospace Sciences Meeting in 2010. In particular, the UM Mach 2.75 Glass Tunnel with a semi-spanning 7.75deg wedge was analyzed in attempts to explore key physics pertinent to SBLI's, including thermodynamic and viscous boundary conditions as well as turbulence modeling. Most of the analyses were 3D CFD simulations using the OVERFLOW flow solver, with additional quasi-1D simulations performed with an in house MATLAB code interfacing with the NIST REFPROP code to explore perfect verses non-ideal air. A fundamental exploration pertaining to the effects of particle image velocimetry (PIV) on post-processing data is also shown. Results from the CFD simulations showed an improvement in agreement with experimental data with key contributions including adding a laminar zone upstream of the wedge and the necessity of mimicking PIV particle lag for comparisons. Results from the quasi-1D simulation showed that there was little difference between perfect and non-ideal air for the configuration presented.

Analyses of newly digitised and reconstructed snow series over the last 100+ years in Switzerland

Science.gov (United States)

Scherrer, S. C.; Wüthrich, C.; Croci-Maspoli, M.; Appenzeller, C.

2010-09-01

Snow is an important socio-economic factor in the Swiss Alpine region (tourism, hydro-electricity, drinking water) and responsible for considerable natural hazards such as avalanches. In addition, high-quality long-term snow series can be used as an excellent indicator of climate change. The objectives of this study are threefold. First, suitable long-term snow series from different altitudes and regions in Switzerland have been selected, missing data digitized and the entire series quality checked. Second, the long-term snow series have been used for trend analyses over a time period >100 years. Third, snow depth series have been reconstructed using daily new snow, temperature and precipitation as input variables. This made it possible to analyse snow depth related variables such as days with snow pack. Results show that the snow cover is varying substantially on seasonal and decadal time scales. The analyses of the decadal new snow trends during the last 100 years shows unprecedented low new snow sums in the winter seasons (DJF) of the 1990s. The 100 year trend of days with snow pack reveals a significant decrease for stations below 800 m asl in the winter season (DJF) and for stations around 1800 m asl in spring (MAM). Similar results were found for seasonal new snow sums. The results of the trend analyses are also discussed with respect to temperature and precipitation trends. Finally we will also shortly discuss how especially "precious" snow measurements have been identified and incorporated in a National Basic Climatological Network (NBCN) as well as in the Global Climate Observing System (GCOS).

Quality of meta-analyses in major leading gastroenterology and hepatology journals: A systematic review.

Science.gov (United States)

Liu, Pengfei; Qiu, Yuanyu; Qian, Yuting; Chen, Xiao; Wang, Yiran; Cui, Jin; Zhai, Xiao

2017-01-01

To appraise the current reporting methodological quality of meta-analyses in five leading gastroenterology and hepatology journals, and to identify the variables associated with the reporting quality. We systematically searched the literature of meta-analyses in Gastroenterology, Gut, Hepatology, Journal of Hepatology (J HEPATOL) and American Journal of Gastroenterology (AM J GASTROENTEROL) from 2006 to 2008 and from 2012 to 2014. Characteristics were extracted based on the PRISMA statement and the AMSTAR tool. Country, number of patients, funding source were also revealed and descriptively reported. A total of 127 meta-analyses were enrolled in this study and were compared among journals, study years, and other characters. Compliances with the PRISMA statement and the AMSTAR checklist were 20.8 ± 4.2 out of a maximum of 27 and 7.6 ± 2.4 out of a maximum of 11, respectively. Some domains were poorly reported including describing a protocol and/or registration (item 5, 0.0%), describing methods, and giving results of additional analyses (item 16, 45.7% and item 23, 48.0%) for PRISMA and duplicating study selection and data extraction (item 2, 53.5%), and providing a list of included and excluded studies (item 5, 14.2%) for AMSTAR. Publication in recent years showed a significantly better methodological quality than those published in previous years. This study shows that methodological reporting quality of MAs in the major gastroenterology and hepatology journals has improved in recent years after the publication of the developed PRISMA statement, and it can be further improved. © 2016 Journal of Gastroenterology and Hepatology Foundation and John Wiley & Sons Australia, Ltd.

Performance and Vibration Analyses of Lift-Offset Helicopters

Directory of Open Access Journals (Sweden)

Jeong-In Go

2017-01-01

Full Text Available A validation study on the performance and vibration analyses of the XH-59A compound helicopter is conducted to establish techniques for the comprehensive analysis of lift-offset compound helicopters. This study considers the XH-59A lift-offset compound helicopter using a rigid coaxial rotor system as a verification model. CAMRAD II (Comprehensive Analytical Method of Rotorcraft Aerodynamics and Dynamics II, a comprehensive analysis code, is used as a tool for the performance, vibration, and loads analyses. A general free wake model, which is a more sophisticated wake model than other wake models, is used to obtain good results for the comprehensive analysis. Performance analyses of the XH-59A helicopter with and without auxiliary propulsion are conducted in various flight conditions. In addition, vibration analyses of the XH-59A compound helicopter configuration are conducted in the forward flight condition. The present comprehensive analysis results are in good agreement with the flight test and previous analyses. Therefore, techniques for the comprehensive analysis of lift-offset compound helicopters are appropriately established. Furthermore, the rotor lifts are calculated for the XH-59A lift-offset compound helicopter in the forward flight condition to investigate the airloads characteristics of the ABC™ (Advancing Blade Concept rotor.

HIFSA: Heavy-Ion Fusion Systems Assessment Project: Volume 2, Technical analyses

International Nuclear Information System (INIS)

Dudziak, D.J.

1987-12-01

A two-year project was undertaken to assess the commercial potential of heavy-ion fusion (HIF) as an economical electric power production technology. Because the US HIF development program is oriented toward the use of multiple-beam induction linacs, the study was confined to this particular driver technology. The HIF systems assessment (HIFSA) study involved several subsystem design, performance, and cost studies (e.g., the induction linac, final beam transport, beam transport in reactor cavity environments, cavity clearing, target manufacturing, and reactor plant). In addition, overall power plant systems integration, parametric analyses, and tradeoff studies were performed using a systems code developed specifically for the HIFSA project. Systems analysis results show values for cost of electricity (COE) comparable to those from other inertial- and magnetic-confinement fusion plant studies; viz., 50 to 60 mills/kWh (1985 dollars) for 1-GWe plant sizes. Also, significant COE insensitivity to major accelerator, target, and reactor parameters near the minima was demonstrated. Conclusions from the HIFSA study have already led to substantial modifications of the US HIF research and development program. Separate abstracts were prepared for 17 papers in these analyses

Metabolic modeling of energy balances in Mycoplasma hyopneumoniae shows that pyruvate addition increases growth rate.

Science.gov (United States)

Kamminga, Tjerko; Slagman, Simen-Jan; Bijlsma, Jetta J E; Martins Dos Santos, Vitor A P; Suarez-Diez, Maria; Schaap, Peter J

2017-10-01

Mycoplasma hyopneumoniae is cultured on large-scale to produce antigen for inactivated whole-cell vaccines against respiratory disease in pigs. However, the fastidious nutrient requirements of this minimal bacterium and the low growth rate make it challenging to reach sufficient biomass yield for antigen production. In this study, we sequenced the genome of M. hyopneumoniae strain 11 and constructed a high quality constraint-based genome-scale metabolic model of 284 chemical reactions and 298 metabolites. We validated the model with time-series data of duplicate fermentation cultures to aim for an integrated model describing the dynamic profiles measured in fermentations. The model predicted that 84% of cellular energy in a standard M. hyopneumoniae cultivation was used for non-growth associated maintenance and only 16% of cellular energy was used for growth and growth associated maintenance. Following a cycle of model-driven experimentation in dedicated fermentation experiments, we were able to increase the fraction of cellular energy used for growth through pyruvate addition to the medium. This increase in turn led to an increase in growth rate and a 2.3 times increase in the total biomass concentration reached after 3-4 days of fermentation, enhancing the productivity of the overall process. The model presented provides a solid basis to understand and further improve M. hyopneumoniae fermentation processes. Biotechnol. Bioeng. 2017;114: 2339-2347. © 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

Graphite analyser upgrade for the IRIS spectrometer at ISIS

International Nuclear Information System (INIS)

Campbell, S.I.; Telling, M.T.F.; Carlile, C.J.

1999-01-01

Complete text of publication follows. The pyrolytic graphite (PG) analyser bank on the IRIS high resolution inelastic spectrometer [1] at ISIS is to be upgraded. At present the analyser consists of 1350 graphite pieces (6 rows by 225 columns) cooled to 25K [2]. The new analyser array, however, will provide a three-fold increase in area and employ 4212 crystal pieces (18 rows by 234 columns). In addition, the graphite crystals will be cooled close to liquid helium temperature to further reduce thermal diffuse scattering (TDS) and improve the sensitivity of the spectrometer [2]. For an instrument such as IRIS, with its analyser in near back-scattering geometry, optical aberration and variation in the time-of-flight of the analysed neutrons is introduced as one moves out from the horizontal scattering plane. To minimise such effects, the profile of the analyser array has been redesigned. The concept behind the design of the new analyser bank and factors that effect the overall resolution of the instrument are discussed. Results of Monte Carlo simulations of the expected resolution and intensity of the complete instrument are presented and compared to the current instrument performance. (author) [1] C.J. Carlile et al, Physica B 182 (1992) 431-440.; [2] C.J. Carlile et al, Nuclear Instruments and Methods In Physics Research A 338 (1994) 78-82

Addition of blood to a phycogenic bone substitute leads to increased in vivo vascularization

International Nuclear Information System (INIS)

Barbeck, Mike; Sader, Robert; Ghanaati, Shahram; Najman, Stevo; Stojanović, Sanja; Živković, Jelena M; Mitić, Žarko; Choukroun, Joseph; Kovačević, Predrag; James Kirkpatrick, C

2015-01-01

The present study aimed to analyze the effects of the addition of blood to the phycogenic bone substitute Algipore ® on the severity of in vivo tissue reaction. Initially, Fourier-transform infrared spectroscopy (FTIR) of the bone substitute was conducted to analyze its chemical composition. The subcutaneous implantation model in Balb/c mice was then applied for up to 30 d to analyze the tissue reactions on the basis of specialized histochemical, immunohistochemical, and histomorphometrical methods. The data of the FTIR analysis showed that the phycogenic bone substitute material is mainly composed of hydroxyapatite with some carbonate content. The in vivo analyses revealed that the addition of blood to Algipore ® had a major impact on both angiogenesis and vessel maturation. The higher vascularization seemed to be based on significantly higher numbers of multinucleated TRAP-positive cells. However, mostly macrophages and a relatively low number of multinucleated giant cells were involved in the tissue reaction to Algipore ® . The presented data show that the addition of blood to a bone substitute impacts the tissue reaction to it. In particular, the immune response and the vascularization were influenced, and these are believed to have a major impact on the regenerative potential of the process of bone tissue regeneration. (paper)

Systematic comparative and sensitivity analyses of additive and outranking techniques for supporting impact significance assessments

International Nuclear Information System (INIS)

Cloquell-Ballester, Vicente-Agustin; Monterde-Diaz, Rafael; Cloquell-Ballester, Victor-Andres; Santamarina-Siurana, Maria-Cristina

2007-01-01

Assessing the significance of environmental impacts is one of the most important and all together difficult processes of Environmental Impact Assessment. This is largely due to the multicriteria nature of the problem. To date, decision techniques used in the process suffer from two drawbacks, namely the problem of compensation and the problem of identification of the 'exact boundary' between sub-ranges. This article discusses these issues and proposes a methodology for determining the significance of environmental impacts based on comparative and sensitivity analyses using the Electre TRI technique. An application of the methodology for the environmental assessment of a Power Plant project within the Valencian Region (Spain) is presented, and its performance evaluated. It is concluded that contrary to other techniques, Electre TRI automatically identifies those cases where allocation of significance categories is most difficult and, when combined with sensitivity analysis, offers greatest robustness in the face of variation in weights of the significance attributes. Likewise, this research demonstrates the efficacy of systematic comparison between Electre TRI and sum-based techniques, in the solution of assignment problems. The proposed methodology can therefore be regarded as a successful aid to the decision-maker, who will ultimately take the final decision

DNA-energetics-based analyses suggest additional genes in ...

Indian Academy of Sciences (India)

2012-06-25

Jun 25, 2012 ... sequence with its homologs in the annotated databases using alignment ... in predictions and on the development of next-generation prediction servers ... sequences, but were not annotated in the organism studied. ...... Biopolymers 52 29–56 .... improvement for identifying translation initiation sites in micro-.

Use of an additive in biofuel to evaluate emissions, engine component wear and lubrication characteristics

International Nuclear Information System (INIS)

Kalam, M.A.; Majsuki, H.H.

2003-01-01

This paper presents the results of experiments carried out to evaluate the effect of adding an anticorrosion additive to blended biofuel and lubricating oil on emissions, engine component wear and lubrication characteristics. The blended biofuels consist of 7.5 and 15 per cent palm olein (PO) with ordinary diesel oil (OD). Pure OD was used for comparison purposes. Exhaust emission gases such as NO x , CO and hydrocarbons (HCs) were measured by an exhaust emission analyser for engine operation on 50 per cent throttle at speeds of 800-3600 r/min. To measure engine component wear and lubricating oil characteristics, the engine was operated at 50 per cent throttle at a speed of 2000 r/min for a period of 100 h with each of the fuel samples. The same lubricating oil, conventional SAE 40, was used in all the fuels. A multielement oil analyser (MOA) was used to measure the increase in wear of metals (Fe, Cu, Al, Pd) and the decrease in lubricating oil additives (Zn, Ca) in the lubricating oil used. An ISL automatic Houillon viscometer (ASTM D445) and potentiometric titration (ASTM D2896) were used to measure viscosity and total base number (TBN) respectively. The results show that the addition of anticorrosion additive with biofuel and lubricating oil improves the emission and engine wear characteristics; both the exhaust emission gases (NO x , CO and HCs) and the wear of metals (Fe, Cu, Al and Pd) decrease with the blended fuels in comparison with the base fuel OD. Detailed results, including engine brake power, are discussed. (Author)

Cloning, characterisation, and comparative quantitative expression analyses of receptor for advanced glycation end products (RAGE) transcript forms.

Science.gov (United States)

Sterenczak, Katharina A; Willenbrock, Saskia; Barann, Matthias; Klemke, Markus; Soller, Jan T; Eberle, Nina; Nolte, Ingo; Bullerdiek, Jörn; Murua Escobar, Hugo

2009-04-01

RAGE is a member of the immunoglobulin superfamily of cell surface molecules playing key roles in pathophysiological processes, e.g. immune/inflammatory disorders, Alzheimer's disease, diabetic arteriosclerosis and tumourigenesis. In humans 19 naturally occurring RAGE splicing variants resulting in either N-terminally or C-terminally truncated proteins were identified and are lately discussed as mechanisms for receptor regulation. Accordingly, deregulation of sRAGE levels has been associated with several diseases e.g. Alzheimer's disease, Type 1 diabetes, and rheumatoid arthritis. Administration of recombinant sRAGE to animal models of cancer blocked tumour growth successfully. In spite of its obvious relationship to cancer and metastasis data focusing sRAGE deregulation and tumours is rare. In this study we screened a set of tumours, healthy tissues and various cancer cell lines for RAGE splicing variants and analysed their structure. Additionally, we analysed the ratio of the mainly found transcript variants using quantitative Real-Time PCR. In total we characterised 24 previously not described canine and 4 human RAGE splicing variants, analysed their structure, classified their characteristics, and derived their respective protein forms. Interestingly, the healthy and the neoplastic tissue samples showed in majority RAGE transcripts coding for the complete receptor and transcripts showing insertions of intron 1.

Atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry of friction modifier additives analyzed directly from base oil solutions.

Science.gov (United States)

Widder, Lukas; Brennerb, Josef; Huttera, Herbert

2014-01-01

To develop new products and to apply measures of quality control quick and simple accessibility of additive composition in automo- tive lubrication is important. The aim of this study was to investigate the possibility of analyzing organic friction modifier additives by means of atmospheric pressure matrix-assisted laser desorption/ionization mass spectrometry [AP-MALDI-MS] from lubricant solu- tions without the use of additional separation techniques. Analyses of selected friction modifier ethoxylated tallow amines and oleic acid amide were compared using two ionization methods, positive-ion electrospray ionization (ESI) and AP-MALDI, using a LTQ Orbitrap mass spectrometer. Pure additives were characterized from solvent solutions, as well as from synthetic and mineral base oil mixtures. Detected ions of pure additive samples consisted mainly of [M + H]+, but also alkaLi metal adducts [M + Na]+ and [M + K]+ could be seen. Characterizations of blends of both friction modifiers from the base oil mixtures were carried out as well and showed significant inten- sities for several additive peaks. Thus, this work shows a method to directly analyze friction modifier additives used in the automotive industry from an oil blend via the use of AP-MALDI without any further separation steps. The method presented will further simplify the acquisition of data on lubricant composition and additives. Furthermore, it allows the perspective of analyzing additive reaction products directly from formulated oil blends.

Neuronal network analyses: premises, promises and uncertainties

OpenAIRE

Parker, David

2010-01-01

Neuronal networks assemble the cellular components needed for sensory, motor and cognitive functions. Any rational intervention in the nervous system will thus require an understanding of network function. Obtaining this understanding is widely considered to be one of the major tasks facing neuroscience today. Network analyses have been performed for some years in relatively simple systems. In addition to the direct insights these systems have provided, they also illustrate some of the diffic...

A systematic review and meta-Analyses show that carbapenem use and medical devices are the leading risk factors for carbapenem- resistant pseudomonas aeruginosa

NARCIS (Netherlands)

A.F. Voor (Anne); J.A. Severin (Juliëtte); E.M.E.H. Lesaffre (Emmanuel); M.C. Vos (Margreet)

2014-01-01

textabstractA systematic review and meta-Analyses were performed to identify the risk factors associated with carbapenem-resistant Pseudomonas aeruginosa and to identify sources and reservoirs for the pathogen. A systematic search of PubMed and Embase databases from 1 January 1987 until 27 January

"Analysing Genre: Language Use in Professional Settings." A Review.

Science.gov (United States)

Drury, Helen

1995-01-01

"Analysing Genre," by Vijay K. Bhatia, is a timely addition to the literature on genre analysis in English for specific purposes. It is divided into three parts: the first provides theoretical background; the second explains how genre analysis works in different academic and professional settings; and the third exemplifies the…

Large-scale association analyses identify new loci influencing glycemic traits and provide insight into the underlying biological pathways

Science.gov (United States)

Scott, Robert A; Lagou, Vasiliki; Welch, Ryan P; Wheeler, Eleanor; Montasser, May E; Luan, Jian’an; Mägi, Reedik; Strawbridge, Rona J; Rehnberg, Emil; Gustafsson, Stefan; Kanoni, Stavroula; Rasmussen-Torvik, Laura J; Yengo, Loïc; Lecoeur, Cecile; Shungin, Dmitry; Sanna, Serena; Sidore, Carlo; Johnson, Paul C D; Jukema, J Wouter; Johnson, Toby; Mahajan, Anubha; Verweij, Niek; Thorleifsson, Gudmar; Hottenga, Jouke-Jan; Shah, Sonia; Smith, Albert V; Sennblad, Bengt; Gieger, Christian; Salo, Perttu; Perola, Markus; Timpson, Nicholas J; Evans, David M; Pourcain, Beate St; Wu, Ying; Andrews, Jeanette S; Hui, Jennie; Bielak, Lawrence F; Zhao, Wei; Horikoshi, Momoko; Navarro, Pau; Isaacs, Aaron; O’Connell, Jeffrey R; Stirrups, Kathleen; Vitart, Veronique; Hayward, Caroline; Esko, Tönu; Mihailov, Evelin; Fraser, Ross M; Fall, Tove; Voight, Benjamin F; Raychaudhuri, Soumya; Chen, Han; Lindgren, Cecilia M; Morris, Andrew P; Rayner, Nigel W; Robertson, Neil; Rybin, Denis; Liu, Ching-Ti; Beckmann, Jacques S; Willems, Sara M; Chines, Peter S; Jackson, Anne U; Kang, Hyun Min; Stringham, Heather M; Song, Kijoung; Tanaka, Toshiko; Peden, John F; Goel, Anuj; Hicks, Andrew A; An, Ping; Müller-Nurasyid, Martina; Franco-Cereceda, Anders; Folkersen, Lasse; Marullo, Letizia; Jansen, Hanneke; Oldehinkel, Albertine J; Bruinenberg, Marcel; Pankow, James S; North, Kari E; Forouhi, Nita G; Loos, Ruth J F; Edkins, Sarah; Varga, Tibor V; Hallmans, Göran; Oksa, Heikki; Antonella, Mulas; Nagaraja, Ramaiah; Trompet, Stella; Ford, Ian; Bakker, Stephan J L; Kong, Augustine; Kumari, Meena; Gigante, Bruna; Herder, Christian; Munroe, Patricia B; Caulfield, Mark; Antti, Jula; Mangino, Massimo; Small, Kerrin; Miljkovic, Iva; Liu, Yongmei; Atalay, Mustafa; Kiess, Wieland; James, Alan L; Rivadeneira, Fernando; Uitterlinden, Andre G; Palmer, Colin N A; Doney, Alex S F; Willemsen, Gonneke; Smit, Johannes H; Campbell, Susan; Polasek, Ozren; Bonnycastle, Lori L; Hercberg, Serge; Dimitriou, Maria; Bolton, Jennifer L; Fowkes, Gerard R; Kovacs, Peter; Lindström, Jaana; Zemunik, Tatijana; Bandinelli, Stefania; Wild, Sarah H; Basart, Hanneke V; Rathmann, Wolfgang; Grallert, Harald; Maerz, Winfried; Kleber, Marcus E; Boehm, Bernhard O; Peters, Annette; Pramstaller, Peter P; Province, Michael A; Borecki, Ingrid B; Hastie, Nicholas D; Rudan, Igor; Campbell, Harry; Watkins, Hugh; Farrall, Martin; Stumvoll, Michael; Ferrucci, Luigi; Waterworth, Dawn M; Bergman, Richard N; Collins, Francis S; Tuomilehto, Jaakko; Watanabe, Richard M; de Geus, Eco J C; Penninx, Brenda W; Hofman, Albert; Oostra, Ben A; Psaty, Bruce M; Vollenweider, Peter; Wilson, James F; Wright, Alan F; Hovingh, G Kees; Metspalu, Andres; Uusitupa, Matti; Magnusson, Patrik K E; Kyvik, Kirsten O; Kaprio, Jaakko; Price, Jackie F; Dedoussis, George V; Deloukas, Panos; Meneton, Pierre; Lind, Lars; Boehnke, Michael; Shuldiner, Alan R; van Duijn, Cornelia M; Morris, Andrew D; Toenjes, Anke; Peyser, Patricia A; Beilby, John P; Körner, Antje; Kuusisto, Johanna; Laakso, Markku; Bornstein, Stefan R; Schwarz, Peter E H; Lakka, Timo A; Rauramaa, Rainer; Adair, Linda S; Smith, George Davey; Spector, Tim D; Illig, Thomas; de Faire, Ulf; Hamsten, Anders; Gudnason, Vilmundur; Kivimaki, Mika; Hingorani, Aroon; Keinanen-Kiukaanniemi, Sirkka M; Saaristo, Timo E; Boomsma, Dorret I; Stefansson, Kari; van der Harst, Pim; Dupuis, Josée; Pedersen, Nancy L; Sattar, Naveed; Harris, Tamara B; Cucca, Francesco; Ripatti, Samuli; Salomaa, Veikko; Mohlke, Karen L; Balkau, Beverley; Froguel, Philippe; Pouta, Anneli; Jarvelin, Marjo-Riitta; Wareham, Nicholas J; Bouatia-Naji, Nabila; McCarthy, Mark I; Franks, Paul W; Meigs, James B; Teslovich, Tanya M; Florez, Jose C; Langenberg, Claudia; Ingelsson, Erik; Prokopenko, Inga; Barroso, Inês

2012-01-01

Through genome-wide association meta-analyses of up to 133,010 individuals of European ancestry without diabetes, including individuals newly genotyped using the Metabochip, we have raised the number of confirmed loci influencing glycemic traits to 53, of which 33 also increase type 2 diabetes risk (q fasting insulin showed association with lipid levels and fat distribution, suggesting impact on insulin resistance. Gene-based analyses identified further biologically plausible loci, suggesting that additional loci beyond those reaching genome-wide significance are likely to represent real associations. This conclusion is supported by an excess of directionally consistent and nominally significant signals between discovery and follow-up studies. Functional follow-up of these newly discovered loci will further improve our understanding of glycemic control. PMID:22885924

Workload analyse of assembling process

Science.gov (United States)

Ghenghea, L. D.

2015-11-01

The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

Preparation and Characterization of SN-38-Encapsulated Phytantriol Cubosomes Containing α-Monoglyceride Additives.

Science.gov (United States)

Ali, Md Ashraf; Noguchi, Shuji; Iwao, Yasunori; Oka, Toshihiko; Itai, Shigeru

2016-01-01

SN-38 is a potent active metabolite of irinotecan that has been considered as an anticancer candidate. However, the clinical development of this compound has been hampered by its poor aqueous solubility and chemical instability. In this study, we developed SN-38-encapsulated cubosomes to resolve these problems. Six α-monoglyceride additives, comprising monocaprylin, monocaprin, monolaurin, monomyristin, monopalmitin, and monostearin, were used to prepare phytantriol (PHYT) cubosomes by probe sonication. The mean particle size, polydispersity index, and zeta potential values of these systems were around 190-230 nm, 0.19-0.25 and -17 to -22 mV, respectively. Small-angle X-ray scattering analyses confirmed that the SN-38-encapsulated cubosomes existed in the Pn̄3m space group both with and without the additives. The monoglyceride additives led to around a two-fold increase in the solubility of SN-38 compared with the PHYT cubosome. The drug entrapment efficiency of PHYT cubosomes with additives was greater than 97%. The results of a stability study at 25°C showed no dramatic changes in the particle size or polydispersity index characteristics, with at least 85% of the SN-38 existing in its active lactone form after 10 d, demonstrating the high stability of the cubosome nanoparticles. Furthermore, approximately 55% of SN-38 was slowly released from the cubosomes with additives over 96 h in vitro under physiological conditions. Taken together, these results show that the SN-38-encapsulated PHYT cubosome particles are promising drug carriers that should be considered for further in vivo experiments, including drug delivery to tumor cells using the enhanced permeability and retention effect.

The phaco machine: analysing new technology.

Science.gov (United States)

Fishkind, William J

2013-01-01

The phaco machine is frequently overlooked as the crucial surgical instrument it is. Understanding how to set parameters is initiated by understanding fundamental concepts of machine function. This study analyses the critical concepts of partial occlusion phaco, occlusion phaco and pump technology. In addition, phaco energy categories as well as variations of phaco energy production are explored. Contemporary power modulations and pump controls allow for the enhancement of partial occlusion phacoemulsification. These significant changes in the anterior chamber dynamics produce a balanced environment for phaco; less complications; and improved patient outcomes.

Comparison of prosthetic models produced by traditional and additive manufacturing methods.

Science.gov (United States)

Park, Jin-Young; Kim, Hae-Young; Kim, Ji-Hwan; Kim, Jae-Hong; Kim, Woong-Chul

2015-08-01

The purpose of this study was to verify the clinical-feasibility of additive manufacturing by comparing the accuracy of four different manufacturing methods for metal coping: the conventional lost wax technique (CLWT); subtractive methods with wax blank milling (WBM); and two additive methods, multi jet modeling (MJM), and micro-stereolithography (Micro-SLA). Thirty study models were created using an acrylic model with the maxillary upper right canine, first premolar, and first molar teeth. Based on the scan files from a non-contact blue light scanner (Identica; Medit Co. Ltd., Seoul, Korea), thirty cores were produced using the WBM, MJM, and Micro-SLA methods, respectively, and another thirty frameworks were produced using the CLWT method. To measure the marginal and internal gap, the silicone replica method was adopted, and the silicone images obtained were evaluated using a digital microscope (KH-7700; Hirox, Tokyo, Japan) at 140X magnification. Analyses were performed using two-way analysis of variance (ANOVA) and Tukey post hoc test (α=.05). The mean marginal gaps and internal gaps showed significant differences according to tooth type (Pmanufacturing method (Pmanufacturing methods were within a clinically allowable range, and, thus, the clinical use of additive manufacturing methods is acceptable as an alternative to the traditional lost wax-technique and subtractive manufacturing.

Analysing harmonic motions with an iPhone’s magnetometer

Science.gov (United States)

Yavuz, Ahmet; Kağan Temiz, Burak

2016-05-01

In this paper, we propose an experiment for analysing harmonic motion using an iPhone’s (or iPad’s) magnetometer. This experiment consists of the detection of magnetic field variations obtained from an iPhone’s magnetometer sensor. A graph of harmonic motion is directly displayed on the iPhone’s screen using the Sensor Kinetics application. Data from this application was analysed with Eureqa software to establish the equation of the harmonic motion. Analyses show that the use of an iPhone’s magnetometer to analyse harmonic motion is a practical and effective method for small oscillations and frequencies less than 15-20 Hz.

A Simple, Reliable Precision Time Analyser

Energy Technology Data Exchange (ETDEWEB)

Joshi, B. V.; Nargundkar, V. R.; Subbarao, K.; Kamath, M. S.; Eligar, S. K. [Atomic Energy Establishment Trombay, Bombay (India)

1966-06-15

A 30-channel time analyser is described. The time analyser was designed and built for pulsed neutron research but can be applied to other uses. Most of the logic is performed by means of ferrite memory core and transistor switching circuits. This leads to great versatility, low power consumption, extreme reliability and low cost. The analyser described provides channel Widths from 10 {mu}s to 10 ms; arbitrarily wider channels are easily obtainable. It can handle counting rates up to 2000 counts/min in each channel with less than 1% dead time loss. There is a provision for an initial delay equal to 100 channel widths. An input pulse de-randomizer unit using tunnel diodes ensures exactly equal channel widths. A brief description of the principles involved in core switching circuitry is given. The core-transistor transfer loop is compared with the usual core-diode loops and is shown to be more versatile and better adapted to the making of a time analyser. The circuits derived from the basic loop are described. These include the scale of ten, the frequency dividers and the delay generator. The current drivers developed for driving the cores are described. The crystal-controlled clock which controls the width of the time channels and synchronizes the operation of the various circuits is described. The detector pulse derandomizer unit using tunnel diodes is described. The scheme of the time analyser is then described showing how the various circuits can be integrated together to form a versatile time analyser. (author)

Improved phylogenetic analyses corroborate a plausible position of Martialis heureka in the ant tree of life.

Directory of Open Access Journals (Sweden)

Patrick Kück

Full Text Available Martialinae are pale, eyeless and probably hypogaeic predatory ants. Morphological character sets suggest a close relationship to the ant subfamily Leptanillinae. Recent analyses based on molecular sequence data suggest that Martialinae are the sister group to all extant ants. However, by comparing molecular studies and different reconstruction methods, the position of Martialinae remains ambiguous. While this sister group relationship was well supported by Bayesian partitioned analyses, Maximum Likelihood approaches could not unequivocally resolve the position of Martialinae. By re-analysing a previous published molecular data set, we show that the Maximum Likelihood approach is highly appropriate to resolve deep ant relationships, especially between Leptanillinae, Martialinae and the remaining ant subfamilies. Based on improved alignments, alignment masking, and tree reconstructions with a sufficient number of bootstrap replicates, our results strongly reject a placement of Martialinae at the first split within the ant tree of life. Instead, we suggest that Leptanillinae are a sister group to all other extant ant subfamilies, whereas Martialinae branch off as a second lineage. This assumption is backed by approximately unbiased (AU tests, additional Bayesian analyses and split networks. Our results demonstrate clear effects of improved alignment approaches, alignment masking and data partitioning. We hope that our study illustrates the importance of thorough, comprehensible phylogenetic analyses using the example of ant relationships.

Processing of pure titanium containing titanium-based reinforcing ceramics additives using spark plasma sintering

Directory of Open Access Journals (Sweden)

Mondiu Olayinka DUROWOJU

2017-06-01

Full Text Available The densification behaviour, microstructural changes and hardness characteristics during spark plasma sintering of CP-Ti reinforced with TiC, TiN, TiCN and TiB2 were investigated. Commercially pure Ti powders were dry mixed with varied amounts (2.5 and 5 wt. % of the ceramic additives using a T2F Turbula mixer for 5 h and at a speed of 49 rpm. The blended composite powders were then sintered using spark plasma sintering system (model HHPD-25 from FCT Germany at a heating rate of 100oC min-1, dwell time of 5 min and sintering temperature of 950ºC. The sintering of CP-Ti was used as a base study to select the proper spark plasma sintering temperature for full density. Densification was monitored through analysis of the recorded punch displacement and the measured density of the sintered samples using Archimedes method. High densities ranging from 97.8% for 5% TiB2 addition to 99.6% for 5% TiCN addition were achieved at a relatively low temperature of 950°C. Microstructural analyses show a uniform distribution of the additives and finer structure showing their inhibitive effect on grain growth. An improved hardness was observed in all the cases with highest values obtained with TiCN as a result of the combined effect of TiC and TiN. A change in the fracture mode from trans granular to intergranular was also observed.

A miniaturised, nested-cylindrical electrostatic analyser geometry for dual electron and ion, multi-energy measurements

Energy Technology Data Exchange (ETDEWEB)

Bedington, Robert, E-mail: r.bedington@nus.edu.sg; Kataria, Dhiren; Smith, Alan

2015-09-01

The CATS (Cylindrical And Tiny Spectrometer) electrostatic optics geometry features multiple nested cylindrical analysers to simultaneously measure multiple energies of electron and multiple energies of ion in a configuration that is targeted at miniaturisation and MEMS fabrication. In the prototyped model, two configurations of cylindrical analyser were used, featuring terminating side-plates that caused particle trajectories to either converge (C type) or diverge (D type) in the axial direction. Simulations show how these different electrode configurations affect the particle focussing and instrument parameters; C-type providing greater throughputs but D-type providing higher resolving powers. The simulations were additionally used to investigate unexpected plate spacing variations in the as-built model, revealing that the k-factors are most sensitive to the width of the inter-electrode spacing at its narrowest point. - Highlights: • A new nested cylindrical miniaturised electrostatic analyser geometry is described. • “Converging” (C) and “diverging” (D) type channel properties are investigated. • C channels are shown to have greater throughputs and D greater resolving powers. • Plate factors are shown to be sensitive to the minimum in inter-electrode spacing.

Electron microscopy analyses and electrical properties of the layered Bi{sub 2}WO{sub 6} phase

Energy Technology Data Exchange (ETDEWEB)

Taoufyq, A. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Département d‘Études des Réacteurs, Laboratoire Dosimétrie Capteurs Instrumentation, CEA Cadarache (France); Société CESIGMA—Signals and Systems, 1576 Chemin de La Planquette, F 83 130 LA GARDE (France); Ait Ahsaine, H. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); Patout, L. [Institut Matériaux Microélectronique et Nanosciences de Provence, IM2NP, UMR CNRS 7334, Université du Sud Toulon-Var, BP 20132, 83957, La Garde Cedex (France); Benlhachemi, A.; Ezahri, M. [Laboratoire Matériaux et Environnement LME, Faculté des Sciences, Université Ibn Zohr, BP 8106, Cité Dakhla, Agadir, Maroc (Morocco); and others

2013-07-15

The bismuth tungstate Bi{sub 2}WO{sub 6} was synthesized using a classical coprecipitation method followed by a calcination process at different temperatures. The samples were characterized by X-ray diffraction, simultaneous thermogravimetry and differential thermal analysis (TGA/DTA), scanning and transmission electron microscopy (SEM, TEM) analyses. The Rietveld analysis and electron diffraction clearly confirmed the Pca2{sub 1} non centrosymmetric space group previously proposed for this phase. The layers Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} have been directly evidenced from the HRTEM images. The electrical properties of Bi{sub 2}WO{sub 6} compacted pellets systems were determined from electrical impedance spectrometry (EIS) and direct current (DC) analyses, under air and argon, between 350 and 700 °C. The direct current analyses showed that the conduction observed from EIS analyses was mainly ionic in this temperature range, with a small electronic contribution. Electrical change above the transition temperature of 660 °C is observed under air and argon atmospheres. The strong conductivity increase observed under argon is interpreted in terms of formation of additional oxygen vacancies coupled with electron conduction. - Graphical abstract: High resolution transmission electron microscopy: inverse fast Fourier transform giving the layered structure of the Bi{sub 2}WO{sub 6} phase, with a representation of the cell dimensions (b and c vectors). The Bi{sub 2}O{sub 2}{sup 2+} and WO{sub 4}{sup 2−} sandwiches are visible in the IFFT image. - Highlights: • Using transmission electron microscopy, we visualize the layered structure of Bi{sub 2}WO{sub 6}. • Electrical analyses under argon gas show some increase in conductivity. • The phase transition at 660 °C is evidenced from electrical modification.

Evaluation of calcium superphosphate as an additive to reduce gas emissions from rabbit manure

Directory of Open Access Journals (Sweden)

Fernando Estellés Barber

2014-12-01

Full Text Available Techniques to reduce the emission of air pollutants from livestock production are demanded. In this study, the effect of an additive (calcium superphosphate on gas emissions from rabbit manure was investigated and compared with a control where no additive was used. Calcium superphosphate was applied at a rate of 100 g/m2 per week in a manure pit during 2 cycles of growing rabbits. Manure samples were collected weekly and then chemically and microbiologically analysed. Gas emissions (ammonia, carbon dioxide, methane and nitrous oxide were determined in 2 open flux chambers. No differences were observed in gas emissions between the treated and control samples except for ammonia emissions, which were reduced by 33% when the additive was applied (P<0.05. No statistical differences were obtained in the microbial content between control and treatment, as results showed a high variability. Dry matter content and pH were the most influential parameters on the emission of gases from manure. According to these results, the application of calcium superphosphate may be considered as an effective technique to reduce ammonia emission from rabbit manure. The additive may also be potentially effective in other species, but additional research is necessary to investigate its performance.

Addition of granular activated carbon and trace elements to favor volatile fatty acid consumption during anaerobic digestion of food waste.

Science.gov (United States)

Capson-Tojo, Gabriel; Moscoviz, Roman; Ruiz, Diane; Santa-Catalina, Gaëlle; Trably, Eric; Rouez, Maxime; Crest, Marion; Steyer, Jean-Philippe; Bernet, Nicolas; Delgenès, Jean-Philippe; Escudié, Renaud

2018-07-01

The effect of supplementing granular activated carbon and trace elements on the anaerobic digestion performance of consecutive batch reactors treating food waste was investigated. The results from the first batch suggest that addition of activated carbon favored biomass acclimation, improving acetic acid consumption and enhancing methane production. Adding trace elements allowed a faster consumption of propionic acid. A second batch proved that a synergy existed when activated carbon and trace elements were supplemented simultaneously. The degradation kinetics of propionate oxidation were particularly improved, reducing significantly the batch duration and improving the average methane productivities. Addition of activated carbon favored the growth of archaea and syntrophic bacteria, suggesting that interactions between these microorganisms were enhanced. Interestingly, microbial analyses showed that hydrogenotrophic methanogens were predominant. This study shows for the first time that addition of granular activated carbon and trace elements may be a feasible solution to stabilize food waste anaerobic digestion. Copyright © 2018 Elsevier Ltd. All rights reserved.

Network class superposition analyses.

Directory of Open Access Journals (Sweden)

Carl A B Pearson

Full Text Available Networks are often used to understand a whole system by modeling the interactions among its pieces. Examples include biomolecules in a cell interacting to provide some primary function, or species in an environment forming a stable community. However, these interactions are often unknown; instead, the pieces' dynamic states are known, and network structure must be inferred. Because observed function may be explained by many different networks (e.g., ≈ 10(30 for the yeast cell cycle process, considering dynamics beyond this primary function means picking a single network or suitable sample: measuring over all networks exhibiting the primary function is computationally infeasible. We circumvent that obstacle by calculating the network class ensemble. We represent the ensemble by a stochastic matrix T, which is a transition-by-transition superposition of the system dynamics for each member of the class. We present concrete results for T derived from boolean time series dynamics on networks obeying the Strong Inhibition rule, by applying T to several traditional questions about network dynamics. We show that the distribution of the number of point attractors can be accurately estimated with T. We show how to generate Derrida plots based on T. We show that T-based Shannon entropy outperforms other methods at selecting experiments to further narrow the network structure. We also outline an experimental test of predictions based on T. We motivate all of these results in terms of a popular molecular biology boolean network model for the yeast cell cycle, but the methods and analyses we introduce are general. We conclude with open questions for T, for example, application to other models, computational considerations when scaling up to larger systems, and other potential analyses.

Neoliberalism in education: Five images of critical analyses

Directory of Open Access Journals (Sweden)

Branislav Pupala

2011-03-01

Full Text Available The survey study brings information about the way that educational researchcopes with neoliberalism as a generalized form of social government in the currentwestern culture. It shows that neoliberalism is considered as a universal scope of otherchanges in the basic segments of education and those theoretical and critical analyses ofthis phenomenon represent an important part of production in the area of educationalresearch. It emphasizes the contribution of formation and development of the socalledgovernmental studies for comprehension of mechanisms and consequences ofneoliberal government of the society and shows how way the methodology of thesestudies helps to identify neoliberal strategies used in the regulation of social subjectsby education. There are five selected segments of critical analyses elaborated (fromthe concept of a lifelong learning, through preschool and university education to theeducation of teachers and PISA project that obviously show ideological and theoreticalcohesiveness of the education analysis through the scope of neoliberal governmentality.

Comparative Genome Analyses of Serratia marcescens FS14 Reveals Its High Antagonistic Potential

Science.gov (United States)

Li, Pengpeng; Kwok, Amy H. Y.; Jiang, Jingwei; Ran, Tingting; Xu, Dongqing; Wang, Weiwu; Leung, Frederick C.

2015-01-01

S. marcescens FS14 was isolated from an Atractylodes macrocephala Koidz plant that was infected by Fusarium oxysporum and showed symptoms of root rot. With the completion of the genome sequence of FS14, the first comprehensive comparative-genomic analysis of the Serratia genus was performed. Pan-genome and COG analyses showed that the majority of the conserved core genes are involved in basic cellular functions, while genomic factors such as prophages contribute considerably to genome diversity. Additionally, a Type I restriction-modification system, a Type III secretion system and tellurium resistance genes are found in only some Serratia species. Comparative analysis further identified that S. marcescens FS14 possesses multiple mechanisms for antagonism against other microorganisms, including the production of prodigiosin, bacteriocins, and multi-antibiotic resistant determinants as well as chitinases. The presence of two evolutionarily distinct Type VI secretion systems (T6SSs) in FS14 may provide further competitive advantages for FS14 against other microbes. To our knowledge, this is the first report of comparative analysis on T6SSs in the genus, which identifies four types of T6SSs in Serratia spp.. Competition bioassays of FS14 against the vital plant pathogenic bacterium Ralstonia solanacearum and fungi Fusarium oxysporum and Sclerotinia sclerotiorum were performed to support our genomic analyses, in which FS14 demonstrated high antagonistic activities against both bacterial and fungal phytopathogens. PMID:25856195

Comparative genome analyses of Serratia marcescens FS14 reveals its high antagonistic potential.

Science.gov (United States)

Li, Pengpeng; Kwok, Amy H Y; Jiang, Jingwei; Ran, Tingting; Xu, Dongqing; Wang, Weiwu; Leung, Frederick C

2015-01-01

S. marcescens FS14 was isolated from an Atractylodes macrocephala Koidz plant that was infected by Fusarium oxysporum and showed symptoms of root rot. With the completion of the genome sequence of FS14, the first comprehensive comparative-genomic analysis of the Serratia genus was performed. Pan-genome and COG analyses showed that the majority of the conserved core genes are involved in basic cellular functions, while genomic factors such as prophages contribute considerably to genome diversity. Additionally, a Type I restriction-modification system, a Type III secretion system and tellurium resistance genes are found in only some Serratia species. Comparative analysis further identified that S. marcescens FS14 possesses multiple mechanisms for antagonism against other microorganisms, including the production of prodigiosin, bacteriocins, and multi-antibiotic resistant determinants as well as chitinases. The presence of two evolutionarily distinct Type VI secretion systems (T6SSs) in FS14 may provide further competitive advantages for FS14 against other microbes. To our knowledge, this is the first report of comparative analysis on T6SSs in the genus, which identifies four types of T6SSs in Serratia spp.. Competition bioassays of FS14 against the vital plant pathogenic bacterium Ralstonia solanacearum and fungi Fusarium oxysporum and Sclerotinia sclerotiorum were performed to support our genomic analyses, in which FS14 demonstrated high antagonistic activities against both bacterial and fungal phytopathogens.

Microstructural analysis of ceramic masses with waste kaolin addition for the red ceramic production

International Nuclear Information System (INIS)

Vida, Talita Almeida; Fagury Neto, Elias; Rabelo, Adriano Alves

2010-01-01

Incorporating reject industrial ceramic mixtures has proved viable in the reduction of environmental liabilities. In this study, we sought to study the potential use of ceramic formulations with the addition of tailings from the production of kaolin clay to the region of the city of Maraba-PA. Formulations were obtained with two clays of this region with the addition of up to 60% by weight of kaolin waste. The microstructural analyses were carried out from the preparation of specimens that were sintered at 1000 and 1200 °C with level 3 hours. The samples prepared were used to observe the microstructure by optical microscope, to determine the constituents of each formulation after burning. And later analysis was performed X-rays diffraction, to quantify the phases present. It was observed that increasing the content of the mixture of kaolin clay caused the reaction of kaolinite forming the primary mullite from 1000 ° C. For a firing temperature around 1200 ° C showed the presence of mullite even the addition of 20% kaolin, noting also the presence of secondary kaolinite. (author)

Additive conjoint measurement for multiattribute utility

NARCIS (Netherlands)

Maas, A.; Wakker, P.P.

1994-01-01

This paper shows that multiattribute utility can be simplified by methods from additive conjoint measurement. Given additive conjoint measurability under certainty, axiomatizations can be simplified, and implementation and reliability of elicitation can be improved. This also contributes to the

Effect of Some Local Additives on the Chemical Constituent of Palm Oil

African Journals Online (AJOL)

Different quantities of palm oil from NIFOR plantation were mixed with some local additives (carrot, paw paw, lime and red dye). The oil samples were analysed for their moisture content, saponification value, iodine value, acid value and free fatty acid value before and after the addition of known and constant amount of the ...

DESIGNING EAP MATERIALS BASED ON INTERCULTURAL CORPUS ANALYSES: THE CASE OF LOGICAL MARKERS IN RESEARCH ARTICLES

Directory of Open Access Journals (Sweden)

Pilar Mur Dueñas

2009-10-01

Full Text Available The ultimate aim of intercultural analyses in English for Academic Purposes is to help non-native scholars function successfully in the international disciplinary community in English. The aim of this paper is to show how corpus-based intercultural analyses can be useful to design EAP materials on a particular metadiscourse category, logical markers, in research article writing. The paper first describes the analysis carried out of additive, contrastive and consecutive logical markers in a corpus of research articles in English and in Spanish in a particular discipline, Business Management. Differences were found in their frequency and also in the use of each of the sub-categories. Then, five activities designed on the basis of these results are presented. They are aimed at raising Spanish Business scholars' awareness of the specific uses and pragmatic function of frequent logical markers in international research articles in English.

Analysing temporal variability of particulate matter and possible contributing factors over Mahabaleshwar, a high-altitude station in Western Ghats, India

Science.gov (United States)

Leena, P. P.; Vijayakumar, K.; Anilkumar, V.; Pandithurai, G.

2017-11-01

Airborne particulate matter (PM) plays a vital role on climate change as well as human health. In the present study, temporal variability associated with mass concentrations of PM10, PM2.5, and PM1.0 were analysed using ground observations from Mahabaleswar (1348 m AMSL, 17.56 0N, 73.4 0E), a high-altitude station in the Western Ghats, India from June 2012 to May 2013. Concentrations of PM10, PM2.5, and PM1.0 showed strong diurnal, monthly, seasonal and weekday-weekend trends. The seasonal variation of PM1.0 and PM2.5 has showed highest concentrations during winter season compared to monsoon and pre-monsoon, but in the case of PM10 it showed highest concentrations in pre-monsoon season. Similarly, slightly higher PM concentrations were observed during weekends compared to weekdays. In addition, possible contributing factors to this temporal variability has been analysed based on the variation of secondary pollutants such as NO2, SO2, CO and O3 and long range transport of dust.

DMPD: Structural and functional analyses of bacterial lipopolysaccharides. [Dynamic Macrophage Pathway CSML Database

Lifescience Database Archive (English)

Full Text Available 12106784 Structural and functional analyses of bacterial lipopolysaccharides. Carof...html) (.csml) Show Structural and functional analyses of bacterial lipopolysaccharides. PubmedID 12106784 Title Structural and functi...onal analyses of bacterial lipopolysaccharides. Authors

Development of CFD fire models for deterministic analyses of the cable issues in the nuclear power plant

International Nuclear Information System (INIS)

Lin, C.-H.; Ferng, Y.-M.; Pei, B.-S.

2009-01-01

Additional fire barriers of electrical cables are required for the nuclear power plants (NPPs) in Taiwan due to the separation requirements of Appendix R to 10 CFR Part 50. The risk-informed fire analysis (RIFA) may provide a viable method to resolve these fire barrier issues. However, it is necessary to perform the fire scenario analyses so that RIFA can quantitatively determine the risk related to the fire barrier wrap. The CFD fire models are then proposed in this paper to help the RIFA in resolving these issues. Three typical fire scenarios are selected to assess the present CFD models. Compared with the experimental data and other model's simulations, the present calculated results show reasonable agreements, rendering that present CFD fire models can provide the quantitative information for RIFA analyses to release the cable wrap requirements for NPPs

Lung function in idiopathic pulmonary fibrosis - extended analyses of the IFIGENIA trial

Directory of Open Access Journals (Sweden)

Verschakelen Johny

2009-10-01

Full Text Available Abstract Background The randomized placebo-controlled IFIGENIA-trial demonstrated that therapy with high-dose N-acetylcysteine (NAC given for one year, added to prednisone and azathioprine, significantly ameliorates (i.e. slows down disease progression in terms of vital capacity (VC (+9% and diffusing capacity (DLco (+24% in idiopathic pulmonary fibrosis (IPF. To better understand the clinical implications of these findings we performed additional, explorative analyses of the IFGENIA data set. Methods We analysed effects of NAC on VC, DLco, a composite physiologic index (CPI, and mortality in the 155 study-patients. Results In trial completers the functional indices did not change significantly with NAC, whereas most indices deteriorated with placebo; in non-completers the majority of indices worsened but decline was generally less pronounced in most indices with NAC than with placebo. Most categorical analyses of VC, DLco and CPI also showed favourable changes with NAC. The effects of NAC on VC, DLco and CPI were significantly better if the baseline CPI was 50 points or lower. Conclusion This descriptive analysis confirms and extends the favourable effects of NAC on lung function in IPF and emphasizes the usefulness of VC, DLco, and the CPI for the evaluation of a therapeutic effect. Most importantly, less progressed disease as indicated by a CPI of 50 points or lower at baseline was more responsive to therapy in this study. Trial Registration Registered at http://www.ClinicalTrials.gov; number NCT00639496.

Optimisation of amylase and xylanase addition in dependance of white flour amylase activity

Directory of Open Access Journals (Sweden)

Lončar Davor M.

2016-01-01

Full Text Available In this study the effect of different quantities of added amylase to white wheat flours characterized with different activities of naturally existing amylases is tested. Response surface methodology is chosen to test the effects of main applied technological parameters on bread quality responses. Independent variables are chosen to be: quantity of added amylase and bulk fermentation time, while analysed responses are: specific volume, grain structure, bulk fermentation. Bread quality responses are statistically significant, while predicted and observed responses correspond very well, which allows good prediction of bread quality parameters based on applied technological parameters and flour characteristics. Score analysis shows that optimum quantity of amylase addition regarding bread quality depends on the activity of naturally existing amylases. Optimal quantity of added xylanase in bread samples made from both flour types is 0.004%. Xylanase improved properties of white wheat bread and higher effect is experienced with flour that has more active naturally existing amylases. Addition of amylase has statistically significantly increased a* values of crust. Addition of xylanase has statistically significantly decreased values of b* in comparison to the respective bread sample with only added amylase.

Criticality safety analyses in SKODA JS a.s

International Nuclear Information System (INIS)

Mikolas, P.; Svarny, J.

1999-01-01

This paper describes criticality safety analyses of spent fuel systems for storage and transport of spent fuel performed in SKODA JS s.r.o.. Analyses were performed for different systems both at NPP site including originally designed spent fuel pool with a large pitch between assemblies without any special absorbing material, high density spent fuel pool with an additional absorption by boron steel, depository rack for fresh fuel assemblies with a very large pitch between fuel assemblies, a container for transport of fresh fuel into the reactor pool and a cask for transport and storage of spent fuel and container for final storage depository. required subcriticality has been proven taking into account all possible unfavourable conditions, uncertainties etc. In two cases, burnup credit methodology is expected to be used. (Authors)

Effect of Additional Structure on Effective Stack Height of Gas Dispersion in Atmosphere

OpenAIRE

Takenobu Michioka; Koichi Sada; Kazuki Okabayashi

2016-01-01

Wind-tunnel experiments were conducted to evaluate the effect of additional structure (building, sea wall and banking) on the effective stack height, which is usually used in safety analyses of nuclear power facilities in Japan. The effective stack heights were estimated with and without the additional structure in addition to the reactor building while varying several conditions such as the source height, the height of additional structure and the distance between the source position and the...

Uncertainty Analyses for Back Projection Methods

Science.gov (United States)

Zeng, H.; Wei, S.; Wu, W.

2017-12-01

So far few comprehensive error analyses for back projection methods have been conducted, although it is evident that high frequency seismic waves can be easily affected by earthquake depth, focal mechanisms and the Earth's 3D structures. Here we perform 1D and 3D synthetic tests for two back projection methods, MUltiple SIgnal Classification (MUSIC) (Meng et al., 2011) and Compressive Sensing (CS) (Yao et al., 2011). We generate synthetics for both point sources and finite rupture sources with different depths, focal mechanisms, as well as 1D and 3D structures in the source region. The 3D synthetics are generated through a hybrid scheme of Direct Solution Method and Spectral Element Method. Then we back project the synthetic data using MUSIC and CS. The synthetic tests show that the depth phases can be back projected as artificial sources both in space and time. For instance, for a source depth of 10km, back projection gives a strong signal 8km away from the true source. Such bias increases with depth, e.g., the error of horizontal location could be larger than 20km for a depth of 40km. If the array is located around the nodal direction of direct P-waves the teleseismic P-waves are dominated by the depth phases. Therefore, back projections are actually imaging the reflection points of depth phases more than the rupture front. Besides depth phases, the strong and long lasted coda waves due to 3D effects near trench can lead to additional complexities tested here. The strength contrast of different frequency contents in the rupture models also produces some variations to the back projection results. In the synthetic tests, MUSIC and CS derive consistent results. While MUSIC is more computationally efficient, CS works better for sparse arrays. In summary, our analyses indicate that the impact of various factors mentioned above should be taken into consideration when interpreting back projection images, before we can use them to infer the earthquake rupture physics.

[Total analysis of organic rubber additives].

Science.gov (United States)

He, Wen-Xuan; Robert, Shanks; You, Ye-Ming

2010-03-01

In the present paper, after middle pressure chromatograph separation using both positive phase and reversed-phase conditions, the organic additives in ethylene-propylene rubber were identified by infrared spectrometer. At the same time, by using solid phase extraction column to maintain the main component-fuel oil in organic additves to avoid its interfering with minor compounds, other organic additves were separated and analysed by GC/Ms. In addition, the remaining active compound such as benzoyl peroxide was identified by CC/Ms, through analyzing acetone extract directly. Using the above mentioned techniques, soften agents (fuel oil, plant oil and phthalte), curing agent (benzoylperoxide), vulcanizing accelerators (2-mercaptobenzothiazole, ethyl thiuram and butyl thiuram), and antiagers (2, 6-Di-tert-butyl-4-methyl phenol and styrenated phenol) in ethylene-propylene rubber were identified. Although the technique was established in ethylene-propylene rubber system, it can be used in other rubber system.

Do men and women show love differently in marriage?

Science.gov (United States)

Schoenfeld, Elizabeth A; Bredow, Carrie A; Huston, Ted L

2012-11-01

In Western societies, women are considered more adept than men at expressing love in romantic relationships. Although scholars have argued that this view of love gives short shrift to men's ways of showing love (e.g., Cancian, 1986; Noller, 1996), the widely embraced premise that men and women "love differently" has rarely been examined empirically. Using data collected at four time points over 13 years of marriage, the authors examined whether love is associated with different behaviors for husbands and wives. Multilevel analyses revealed that, counter to theoretical expectations, both genders were equally likely to show love through affection. But whereas wives expressed love by enacting fewer negative or antagonistic behaviors, husbands showed love by initiating sex, sharing leisure activities, and doing household work together with their wives. Overall, the findings indicate that men and women show their love in more nuanced ways than cultural stereotypes suggest.

Defining Investment Additionality for CDM projects - practical approaches

International Nuclear Information System (INIS)

Greiner, Sandra; Michaelowa, Axel

2003-01-01

The environmental integrity of the CDM under the Kyoto Protocol depends on the possibility to avoid giving emission credits to projects that would have happened anyway. Whether and how 'Investment Additionality' of CDM projects has to be determined is currently a part of climate negotiations. We discuss the rationale of companies to invest in projects and analyse possible criteria to determine Investment Additionality from a theoretical point of view. Differences in the type of investment call for the application of different criteria. Although some criteria are better than others, no single criterion can outweigh the others in all respects. We therefore suggest a scheme for additionality testing that aims at matching types of investment and criteria in a sensible way. Criteria are evaluated on the grounds of robustness to manipulation, degree of coverage and appropriateness for testing the investment decision under consideration

Additive Manufacturing for Cost Efficient Production of Compact Ceramic Heat Exchangers and Recuperators

Energy Technology Data Exchange (ETDEWEB)

Shulman, Holly [Ceralink Incorporated, Troy, NY (United States); Ross, Nicole [Ceralink Incorporated, Troy, NY (United States)

2015-10-30

An additive manufacture technique known as laminated object manufacturing (LOM) was used to fabricate compact ceramic heat exchanger prototypes. LOM uses precision CO2 laser cutting of ceramic green tapes, which are then precision stacked to build a 3D object with fine internal features. Modeling was used to develop prototype designs and predict the thermal response, stress, and efficiency in the ceramic heat exchangers. Build testing and materials analyses were used to provide feedback for the design selection. During this development process, laminated object manufacturing protocols were established. This included laser optimization, strategies for fine feature integrity, lamination fluid control, green handling, and firing profile. Three full size prototypes were fabricated using two different designs. One prototype was selected for performance testing. During testing, cross talk leakage prevented the application of a high pressure differential, however, the prototype was successful at withstanding the high temperature operating conditions (1300 °F). In addition, analysis showed that the bulk of the part did not have cracks or leakage issues. This led to the development of a module method for next generation LOM heat exchangers. A scale-up cost analysis showed that given a purpose built LOM system, these ceramic heat exchangers would be affordable for the applications.

Analyses of GIMMS NDVI Time Series in Kogi State, Nigeria

Science.gov (United States)

Palka, Jessica; Wessollek, Christine; Karrasch, Pierre

2017-10-01

The value of remote sensing data is particularly evident where an areal monitoring is needed to provide information on the earth's surface development. The use of temporal high resolution time series data allows for detecting short-term changes. In Kogi State in Nigeria different vegetation types can be found. As the major population in this region is living in rural communities with crop farming the existing vegetation is slowly being altered. The expansion of agricultural land causes loss of natural vegetation, especially in the regions close to the rivers which are suitable for crop production. With regard to these facts, two questions can be dealt with covering different aspects of the development of vegetation in the Kogi state, the determination and evaluation of the general development of the vegetation in the study area (trend estimation) and analyses on a short-term behavior of vegetation conditions, which can provide information about seasonal effects in vegetation development. For this purpose, the GIMMS-NDVI data set, provided by the NOAA, provides information on the normalized difference vegetation index (NDVI) in a geometric resolution of approx. 8 km. The temporal resolution of 15 days allows the already described analyses. For the presented analysis data for the period 1981-2012 (31 years) were used. The implemented workflow mainly applies methods of time series analysis. The results show that in addition to the classical seasonal development, artefacts of different vegetation periods (several NDVI maxima) can be found in the data. The trend component of the time series shows a consistently positive development in the entire study area considering the full investigation period of 31 years. However, the results also show that this development has not been continuous and a simple linear modeling of the NDVI increase is only possible to a limited extent. For this reason, the trend modeling was extended by procedures for detecting structural breaks in

Jauch-Piron States and σ-Additivity

Science.gov (United States)

Bunce, L. J.; Hamhalter, Jan

We study σ-additivity of the physically plausible Jauch-Piron states on a von Neumann algebra M. Amongst other consequences we extend our earlier results [5] by showing that geometric conditions much weaker than pureness imply σ-additivity for a Jauch-Piron state and, further, that if M is properly infinite and the continuum hypothesis is assumed to be true then all Jauch-Piron factor states are σ-additive.

Additional Development and Systems Analyses of Pneumatic Technology for High Speed Civil Transport Aircraft

Science.gov (United States)

Englar, Robert J.; Willie, F. Scott; Lee, Warren J.

1999-01-01

In the Task I portion of this NASA research grant, configuration development and experimental investigations have been conducted on a series of pneumatic high-lift and control surface devices applied to a generic High Speed Civil Transport (HSCT) model configuration to determine their potential for improved aerodynamic performance, plus stability and control of higher performance aircraft. These investigations were intended to optimize pneumatic lift and drag performance; provide adequate control and longitudinal stability; reduce separation flowfields at high angle of attack; increase takeoff/climbout lift-to-drag ratios; and reduce system complexity and weight. Experimental aerodynamic evaluations were performed on a semi-span HSCT generic model with improved fuselage fineness ratio and with interchangeable plain flaps, blown flaps, pneumatic Circulation Control Wing (CCW) high-lift configurations, plain and blown canards, a novel Circulation Control (CC) cylinder blown canard, and a clean cruise wing for reference. Conventional tail power was also investigated for longitudinal trim capability. Also evaluated was unsteady pulsed blowing of the wing high-lift system to determine if reduced pulsed mass flow rates and blowing requirements could be made to yield the same lift as that resulting from steady-state blowing. Depending on the pulsing frequency applied, reduced mass flow rates were indeed found able to provide lift augmentation at lesser blowing values than for the steady conditions. Significant improvements in the aerodynamic characteristics leading to improved performance and stability/control were identified, and the various components were compared to evaluate the pneumatic potential of each. Aerodynamic results were provided to the Georgia Tech Aerospace System Design Lab. to conduct the companion system analyses and feasibility study (Task 2) of theses concepts applied to an operational advanced HSCT aircraft. Results and conclusions from these

The order of draw of blood specimens into additive containing tubes not affect potassium and calcium measurements.

Science.gov (United States)

Majid, A; Heaney, D C; Padmanabhan, N; Spooner, R

1996-12-01

The effect of order of draw when taking blood into tubes containing additive was investigated in 47 medical inpatients; 12 of these patients acted as a control group. The samples were analysed in the order in which they were withdrawn. The results of potassium and calcium concentrations did not differ significantly between groups. Manufacturers recommend a specific order of draw when taking blood using vacuum based blood collection systems, which are routinely used in many hospitals. The results of this study, however, show that order of draw has no effect on calcium or potassium concentrations.

Homeopathy: meta-analyses of pooled clinical data.

Science.gov (United States)

Hahn, Robert G

2013-01-01

In the first decade of the evidence-based era, which began in the mid-1990s, meta-analyses were used to scrutinize homeopathy for evidence of beneficial effects in medical conditions. In this review, meta-analyses including pooled data from placebo-controlled clinical trials of homeopathy and the aftermath in the form of debate articles were analyzed. In 1997 Klaus Linde and co-workers identified 89 clinical trials that showed an overall odds ratio of 2.45 in favor of homeopathy over placebo. There was a trend toward smaller benefit from studies of the highest quality, but the 10 trials with the highest Jadad score still showed homeopathy had a statistically significant effect. These results challenged academics to perform alternative analyses that, to demonstrate the lack of effect, relied on extensive exclusion of studies, often to the degree that conclusions were based on only 5-10% of the material, or on virtual data. The ultimate argument against homeopathy is the 'funnel plot' published by Aijing Shang's research group in 2005. However, the funnel plot is flawed when applied to a mixture of diseases, because studies with expected strong treatments effects are, for ethical reasons, powered lower than studies with expected weak or unclear treatment effects. To conclude that homeopathy lacks clinical effect, more than 90% of the available clinical trials had to be disregarded. Alternatively, flawed statistical methods had to be applied. Future meta-analyses should focus on the use of homeopathy in specific diseases or groups of diseases instead of pooling data from all clinical trials. © 2013 S. Karger GmbH, Freiburg.

Fracture Mechanics Analyses of Reinforced Carbon-Carbon Wing-Leading-Edge Panels

Science.gov (United States)

Raju, Ivatury S.; Phillips, Dawn R.; Knight, Norman F., Jr.; Song, Kyongchan

2010-01-01

Fracture mechanics analyses of subsurface defects within the joggle regions of the Space Shuttle wing-leading-edge RCC panels are performed. A 2D plane strain idealized joggle finite element model is developed to study the fracture behavior of the panels for three distinct loading conditions - lift-off and ascent, on-orbit, and entry. For lift-off and ascent, an estimated bounding aerodynamic pressure load is used for the analyses, while for on-orbit and entry, thermo-mechanical analyses are performed using the extreme cold and hot temperatures experienced by the panels. In addition, a best estimate for the material stress-free temperature is used in the thermo-mechanical analyses. In the finite element models, the substrate and coating are modeled separately as two distinct materials. Subsurface defects are introduced at the coating-substrate interface and within the substrate. The objective of the fracture mechanics analyses is to evaluate the defect driving forces, which are characterized by the strain energy release rates, and determine if defects can become unstable for each of the loading conditions.

Self-assembled two-dimensional gold nanoparticle film for sensitive nontargeted analysis of food additives with surface-enhanced Raman spectroscopy.

Science.gov (United States)

Wu, Yiping; Yu, Wenfang; Yang, Benhong; Li, Pan

2018-05-15

The use of different food additives and their active metabolites has been found to cause serious problems to human health. Thus, considering the potential effects on human health, developing a sensitive and credible analytical method for different foods is important. Herein, the application of solvent-driven self-assembled Au nanoparticles (Au NPs) for the rapid and sensitive detection of food additives in different commercial products is reported. The assembled substrates are highly sensitive and exhibit excellent uniformity and reproducibility because of uniformly distributed and high-density hot spots. The sensitive analyses of ciprofloxacin (CF), diethylhexyl phthalate (DEHP), tartrazine and azodicarbonamide at the 0.1 ppm level using this surface-enhanced Raman spectroscopy (SERS) substrate are given, and the results show that Au NP arrays can serve as efficient SERS substrates for the detection of food additives. More importantly, SERS spectra of several commercial liquors and sweet drinks are obtained to evaluate the addition of illegal additives. This SERS active platform can be used as an effective strategy in the detection of prohibited additives in food.

Thermogravimetric and x-ray diffraction analyses of Luna-24 regolith samples

International Nuclear Information System (INIS)

Deshpande, V.V.; Dharwadkar, S.R.; Jakkal, V.S.

1979-01-01

Two samples of Luna-24 were analysed by X-ray diffraction and thermogravimetric (TG) techniques. The sample 24123.12 shows a weight loss of nearly 0.85 percent between 23O-440deg C and followed by 1.16 percent weight gain from 500 to 800deg C. The sample 23190.13 showed only a weight gain of about 1.5 percent from 5O0deg C to 900deg C. X-ray diffraction analyses show the presence of olivine, plagioclase, pigeonite, enstatite, and native iron in both the virgin samples. The heated samples, however, show that only the native iron got oxidized to iron oxide. The other constituents remain unaltered. (auth.)

Single-trait and multi-trait genome-wide association analyses identify novel loci for blood pressure in African-ancestry populations.

Directory of Open Access Journals (Sweden)

Jingjing Liang

2017-05-01

Full Text Available Hypertension is a leading cause of global disease, mortality, and disability. While individuals of African descent suffer a disproportionate burden of hypertension and its complications, they have been underrepresented in genetic studies. To identify novel susceptibility loci for blood pressure and hypertension in people of African ancestry, we performed both single and multiple-trait genome-wide association analyses. We analyzed 21 genome-wide association studies comprised of 31,968 individuals of African ancestry, and validated our results with additional 54,395 individuals from multi-ethnic studies. These analyses identified nine loci with eleven independent variants which reached genome-wide significance (P < 1.25×10-8 for either systolic and diastolic blood pressure, hypertension, or for combined traits. Single-trait analyses identified two loci (TARID/TCF21 and LLPH/TMBIM4 and multiple-trait analyses identified one novel locus (FRMD3 for blood pressure. At these three loci, as well as at GRP20/CDH17, associated variants had alleles common only in African-ancestry populations. Functional annotation showed enrichment for genes expressed in immune and kidney cells, as well as in heart and vascular cells/tissues. Experiments driven by these findings and using angiotensin-II induced hypertension in mice showed altered kidney mRNA expression of six genes, suggesting their potential role in hypertension. Our study provides new evidence for genes related to hypertension susceptibility, and the need to study African-ancestry populations in order to identify biologic factors contributing to hypertension.

BWR core melt progression phenomena: Experimental analyses

International Nuclear Information System (INIS)

Ott, L.J.

1992-01-01

In the BWR Core Melt in Progression Phenomena Program, experimental results concerning severe fuel damage and core melt progression in BWR core geometry are used to evaluate existing models of the governing phenomena. These include control blade eutectic liquefaction and the subsequent relocation and attack on the channel box structure; oxidation heating and hydrogen generation; Zircaloy melting and relocation; and the continuing oxidation of zirconium with metallic blockage formation. Integral data have been obtained from the BWR DF-4 experiment in the ACRR and from BWR tests in the German CORA exreactor fuel-damage test facility. Additional integral data will be obtained from new CORA BWR test, the full-length FLHT-6 BWR test in the NRU test reactor, and the new program of exreactor experiments at Sandia National Laboratories (SNL) on metallic melt relocation and blockage formation. an essential part of this activity is interpretation and use of the results of the BWR tests. The Oak Ridge National Laboratory (ORNL) has developed experiment-specific models for analysis of the BWR experiments; to date, these models have permitted far more precise analyses of the conditions in these experiments than has previously been available. These analyses have provided a basis for more accurate interpretation of the phenomena that the experiments are intended to investigate. The results of posttest analyses of BWR experiments are discussed and significant findings from these analyses are explained. The ORNL control blade/canister models with materials interaction, relocation and blockage models are currently being implemented in SCDAP/RELAP5 as an optional structural component

Analysing User Lifetime in Voluntary Online Collaboration

DEFF Research Database (Denmark)

McHugh, Ronan; Larsen, Birger

2010-01-01

This paper analyses persuasion in online collaboration projects. It introduces a set of heuristics that can be applied to such projects and combines these with a quantitative analysis of user activity over time. Two example sites are studies, Open Street Map and The Pirate Bay. Results show that ...

Hybrid Logical Analyses of the Ambient Calculus

DEFF Research Database (Denmark)

Bolander, Thomas; Hansen, Rene Rydhof

2010-01-01

In this paper, hybrid logic is used to formulate three control flow analyses for Mobile Ambients, a process calculus designed for modelling mobility. We show that hybrid logic is very well-suited to express the semantic structure of the ambient calculus and how features of hybrid logic can...

Reaffirmation of additional (supplementary payments in company law of Republic of Serbia

Directory of Open Access Journals (Sweden)

Šogorov Stevan

2012-01-01

Full Text Available Subject matter of this article is development of legal regulation if additional payments in Serbia, from 1937 Commercial Code of Kingdom of Yugoslavia till nowadays. In introductory part author underlines legal nature, commercial function and importance of additional payments in private companies, with downfalls in regulation, court and busyness practice. 1988 Enterprise Act and 2004 Company Act has no regulations at all regarding additional payments. 1996 Enterprise Act and 2011 Company Act have provisions on additional payments, but with numerous weaknesses and open questions. Though critical analyses author underlines basic characteristics of additional payments included critical issues which may be expected during application of new legislature.

Influence of the yeast autolysates addition on the volatile compounds of sparkling white wines

Directory of Open Access Journals (Sweden)

Pérez-Magariño Silvia

2014-01-01

Full Text Available During sparkling wine aging, different compounds such as polysaccharides can be released due to yeast autolysis that can cause important changes in wine composition. Yeast autolysis is a slow natural process that takes long time, and the addition of some products could improve the quality of these wines. The aim of this work was to study the effect of the addition of several commercial yeast autolysates on the volatile composition of white sparkling wines (Godello and Verdejo, and aged on lees for 9 months. The discriminant analyses indicated that the sparkling wines treated with PCP2 showed the highest differences in the volatile composition of both sparkling wines studied, being the ethyl esters, terpenes, decanoic acid and some alcohols, the compounds that were affected in a greater extent. This fact could be due to PCP2 presenting the highest mannoprotein percentage that can interact with volatile compounds, modulating their volatility and perception.

Combined analyses of bacterial, fungal and nematode communities in andosolic agricultural soils in Japan.

Science.gov (United States)

Bao, Zhihua; Ikunaga, Yoko; Matsushita, Yuko; Morimoto, Sho; Takada-Hoshino, Yuko; Okada, Hiroaki; Oba, Hirosuke; Takemoto, Shuhei; Niwa, Shigeru; Ohigashi, Kentaro; Suzuki, Chika; Nagaoka, Kazunari; Takenaka, Makoto; Urashima, Yasufumi; Sekiguchi, Hiroyuki; Kushida, Atsuhiko; Toyota, Koki; Saito, Masanori; Tsushima, Seiya

2012-01-01

We simultaneously examined the bacteria, fungi and nematode communities in Andosols from four agro-geographical sites in Japan using polymerase chain reaction-denaturing gradient gel electrophoresis (PCR-DGGE) and statistical analyses to test the effects of environmental factors including soil properties on these communities depending on geographical sites. Statistical analyses such as Principal component analysis (PCA) and Redundancy analysis (RDA) revealed that the compositions of the three soil biota communities were strongly affected by geographical sites, which were in turn strongly associated with soil characteristics such as total C (TC), total N (TN), C/N ratio and annual mean soil temperature (ST). In particular, the TC, TN and C/N ratio had stronger effects on bacterial and fungal communities than on the nematode community. Additionally, two-way cluster analysis using the combined DGGE profile also indicated that all soil samples were classified into four clusters corresponding to the four sites, showing high site specificity of soil samples, and all DNA bands were classified into four clusters, showing the coexistence of specific DGGE bands of bacteria, fungi and nematodes in Andosol fields. The results of this study suggest that geography relative to soil properties has a simultaneous impact on soil microbial and nematode community compositions. This is the first combined profile analysis of bacteria, fungi and nematodes at different sites with agricultural Andosols.

Versatility of cooperative transcriptional activation: a thermodynamical modeling analysis for greater-than-additive and less-than-additive effects.

Directory of Open Access Journals (Sweden)

Till D Frank

Full Text Available We derive a statistical model of transcriptional activation using equilibrium thermodynamics of chemical reactions. We examine to what extent this statistical model predicts synergy effects of cooperative activation of gene expression. We determine parameter domains in which greater-than-additive and less-than-additive effects are predicted for cooperative regulation by two activators. We show that the statistical approach can be used to identify different causes of synergistic greater-than-additive effects: nonlinearities of the thermostatistical transcriptional machinery and three-body interactions between RNA polymerase and two activators. In particular, our model-based analysis suggests that at low transcription factor concentrations cooperative activation cannot yield synergistic greater-than-additive effects, i.e., DNA transcription can only exhibit less-than-additive effects. Accordingly, transcriptional activity turns from synergistic greater-than-additive responses at relatively high transcription factor concentrations into less-than-additive responses at relatively low concentrations. In addition, two types of re-entrant phenomena are predicted. First, our analysis predicts that under particular circumstances transcriptional activity will feature a sequence of less-than-additive, greater-than-additive, and eventually less-than-additive effects when for fixed activator concentrations the regulatory impact of activators on the binding of RNA polymerase to the promoter increases from weak, to moderate, to strong. Second, for appropriate promoter conditions when activator concentrations are increased then the aforementioned re-entrant sequence of less-than-additive, greater-than-additive, and less-than-additive effects is predicted as well. Finally, our model-based analysis suggests that even for weak activators that individually induce only negligible increases in promoter activity, promoter activity can exhibit greater-than-additive

Willingness to Pay Additional Water Rate and Irrigation Knowledge of Farmers in Dinar Karakuyu Irrigation Areas in Turkey

Directory of Open Access Journals (Sweden)

Mevlüt Gül

2017-08-01

Full Text Available Water which has become commodity product which is an important product today. Turkey is not a water rich country. In this study, agricultural enterprises in the field of Irrigation Project in Dinar Karakuyu which was implemented in 1992 by DSI. The study analysed which factors affect the willingness to pay additional irrigation water rate with the help of logit model and the irrigation knowledge of farmers was determined by Likert scale. Dinar Karakuyu irrigation network has begun to lose the function in the region. It was supposed 100% irrigation rate but decreased by approximately 9% today. In this context, DSI (General Directorate of State Hydraulic Works plans to rehabilitation work in the same area. The main material of this study was data obtained from 67 agricultural enterprises through a survey covered by the Irrigation Rehabilitation Project in the province of Afyonkarahisar Karakuyu Dinar. The data was gathered with the help of questionnaires which were answered by farmers in Karakuyu Dinar region. The results indicated that 74.6% of farmers were willingness to pay additional water charge. The data were statistically analysed with the use of the logit model. The model results show that agricultural income, farmers’ educational level, computer ownership, attendance of agricultural training activities, family size and agricultural experience were positive factors affect farmers’ willingness to pay additional water fee.

Comparative genome analyses of Serratia marcescens FS14 reveals its high antagonistic potential.

Directory of Open Access Journals (Sweden)

Pengpeng Li

Full Text Available S. marcescens FS14 was isolated from an Atractylodes macrocephala Koidz plant that was infected by Fusarium oxysporum and showed symptoms of root rot. With the completion of the genome sequence of FS14, the first comprehensive comparative-genomic analysis of the Serratia genus was performed. Pan-genome and COG analyses showed that the majority of the conserved core genes are involved in basic cellular functions, while genomic factors such as prophages contribute considerably to genome diversity. Additionally, a Type I restriction-modification system, a Type III secretion system and tellurium resistance genes are found in only some Serratia species. Comparative analysis further identified that S. marcescens FS14 possesses multiple mechanisms for antagonism against other microorganisms, including the production of prodigiosin, bacteriocins, and multi-antibiotic resistant determinants as well as chitinases. The presence of two evolutionarily distinct Type VI secretion systems (T6SSs in FS14 may provide further competitive advantages for FS14 against other microbes. To our knowledge, this is the first report of comparative analysis on T6SSs in the genus, which identifies four types of T6SSs in Serratia spp.. Competition bioassays of FS14 against the vital plant pathogenic bacterium Ralstonia solanacearum and fungi Fusarium oxysporum and Sclerotinia sclerotiorum were performed to support our genomic analyses, in which FS14 demonstrated high antagonistic activities against both bacterial and fungal phytopathogens.

Chemical stabilization of polymers: Implications for dermal exposure to additives.

Science.gov (United States)

Bartsch, N; Girard, M; Schneider, L; Weijgert, V Van De; Wilde, A; Kappenstein, O; Vieth, B; Hutzler, C; Luch, A

2018-04-16

Technical benefits of additives in polymers stand in marked contrast to their associated health risks. Here, a multi-analyte method based on gas chromatography coupled to tandem mass spectrometry (GC-MS/MS) was developed to quantify polymer additives in complex matrices such as low-density polyethylene (LDPE) and isolated human skin layers after dermal exposure ex vivo. That way both technical aspects and dermal exposure were investigated. The effects of polymer additivation on the material were studied using the example of LDPE. To this end, a tailor-made polymer was applied in aging studies that had been furnished with two different mixtures of phenol- and diarylamine-based antioxidants, plasticizers and processing aids. Upon accelerated thermo-oxidative aging of the material, the formation of LDPE degradation products was monitored with attenuated total reflectance-Fourier transformed infrared (ATR-FTIR) spectroscopy. Compared to pure LDPE, a protective effect of added antioxidants could be observed on the integrity of the polymer. Further, thermo-oxidative degradation of the additives and its kinetics were investigated using LDPE or squalane as matrix. The half-lives of additives in both matrices revealed significant differences between the tested additives as well as between LDPE and squalane. For instance, 2-tert-butyl-6-[(3-tert-butyl-2-hydroxy-5-methylphenyl)methyl]-4-methylphenol (Antioxidant 2246) showed a half-life 12 times lower when incorporated in LDPE as compared to squalane. As a model for dermal exposure of consumers, human skin was brought into contact with the tailor-made LDPE containing additives ex vivo in static Franz diffusion cells. The skin was then analyzed for additives and decomposition products. This study proved 10 polymer additives of diverse pysicochemical properties and functionalities to migrate out of the polymer and eventually overcome the intact human skin barrier during contact. Moreover, their individual distribution within

Physical characterization of biomass-based pyrolysis liquids. Application of standard fuel oil analyses

Energy Technology Data Exchange (ETDEWEB)

Oasmaa, A; Leppaemaeki, E; Koponen, P; Levander, J; Tapola, E [VTT Energy, Espoo (Finland). Energy Production Technologies

1998-12-31

The main purpose of the study was to test the applicability of standard fuel oil methods developed for petroleum-based fuels to pyrolysis liquids. In addition, research on sampling, homogeneity, stability, miscibility and corrosivity was carried out. The standard methods have been tested for several different pyrolysis liquids. Recommendations on sampling, sample size and small modifications of standard methods are presented. In general, most of the methods can be used as such but the accuracy of the analysis can be improved by minor modifications. Fuel oil analyses not suitable for pyrolysis liquids have been identified. Homogeneity of the liquids is the most critical factor in accurate analysis. The presence of air bubbles may disturb in several analyses. Sample preheating and prefiltration should be avoided when possible. The former may cause changes in the composition and structure of the pyrolysis liquid. The latter may remove part of organic material with particles. The size of the sample should be determined on the basis of the homogeneity and the water content of the liquid. The basic analyses of the Technical Research Centre of Finland (VTT) include water, pH, solids, ash, Conradson carbon residue, heating value, CHN, density, viscosity, pourpoint, flash point, and stability. Additional analyses are carried out when needed. (orig.) 53 refs.

Physical Properties of Nanostructured CdO Films from Alkaline Baths Containing Saccharin as Additive

Directory of Open Access Journals (Sweden)

Bünyamin Şahin

2013-01-01

Full Text Available Nanostructured cadmium oxide (CdO films were fabricated on glass substrates from alkaline baths containing saccharin as an additive by a successive ionic layer adsorption and reaction (SILAR method. The effects of saccharin concentration in the bath on the structural, morphological, and optical properties were studied by means of scanning electron microscopy (SEM, X-ray diffraction (XRD, photoluminescence, and Raman spectroscopy. The analyses showed that the surface morphologies, XRD peak intensities, Raman spectroscopy, and photoluminescence properties of CdO films changed with saccharin concentration. From the results, it can be said that morphological characteristic and optical properties of the films could be calibrated by adding various saccharin percentages in the growth bath.

Mechanical properties of additively manufactured octagonal honeycombs

Energy Technology Data Exchange (ETDEWEB)

Hedayati, R., E-mail: rezahedayati@gmail.com [Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Hafez Ave, Tehran (Iran, Islamic Republic of); Department of Biomechanical Engineering, Faculty of Mechanical, Maritime, and Materials Engineering, Delft University of Technology (TU Delft), Mekelweg 2, 2628 CD Delft (Netherlands); Sadighi, M.; Mohammadi-Aghdam, M. [Department of Mechanical Engineering, Amirkabir University of Technology (Tehran Polytechnic), Hafez Ave, Tehran (Iran, Islamic Republic of); Zadpoor, A.A. [Department of Biomechanical Engineering, Faculty of Mechanical, Maritime, and Materials Engineering, Delft University of Technology (TU Delft), Mekelweg 2, 2628 CD Delft (Netherlands)

2016-12-01

Honeycomb structures have found numerous applications as structural and biomedical materials due to their favourable properties such as low weight, high stiffness, and porosity. Application of additive manufacturing and 3D printing techniques allows for manufacturing of honeycombs with arbitrary shape and wall thickness, opening the way for optimizing the mechanical and physical properties for specific applications. In this study, the mechanical properties of honeycomb structures with a new geometry, called octagonal honeycomb, were investigated using analytical, numerical, and experimental approaches. An additive manufacturing technique, namely fused deposition modelling, was used to fabricate the honeycomb from polylactic acid (PLA). The honeycombs structures were then mechanically tested under compression and the mechanical properties of the structures were determined. In addition, the Euler-Bernoulli and Timoshenko beam theories were used for deriving analytical relationships for elastic modulus, yield stress, Poisson's ratio, and buckling stress of this new design of honeycomb structures. Finite element models were also created to analyse the mechanical behaviour of the honeycombs computationally. The analytical solutions obtained using Timoshenko beam theory were close to computational results in terms of elastic modulus, Poisson's ratio and yield stress, especially for relative densities smaller than 25%. The analytical solutions based on the Timoshenko analytical solution and the computational results were in good agreement with experimental observations. Finally, the elastic properties of the proposed honeycomb structure were compared to those of other honeycomb structures such as square, triangular, hexagonal, mixed, diamond, and Kagome. The octagonal honeycomb showed yield stress and elastic modulus values very close to those of regular hexagonal honeycombs and lower than the other considered honeycombs. - Highlights: • The octagonal

Premature death of adult adoptees: analyses of a case-cohort sample.

Science.gov (United States)

Petersen, Liselotte; Andersen, Per Kragh; Sørensen, Thorkild I A

2005-05-01

Genetic and environmental influence on risk of premature death in adulthood was investigated by estimating the associations in total and cause-specific mortality of adult Danish adoptees and their biological and adoptive parents. Among all 14,425 non-familial adoptions formally granted in Denmark during the period 1924 through 1947, we selected the study population according to a case-cohort sampling design. As the case-control design, the case-cohort design has the advantage of economic data collection and little loss in statistical efficiency, but the case-cohort sample has the additional advantages that rate ratio estimates may be obtained, and re-use of the cohort sample in future studies of other outcomes is possible. Analyses were performed using Kalbfleisch and Lawless's estimator for hazard ratio, and robust estimation for variances. In the main analyses the sample was restricted to birth years of the adoptees 1924 and after, and age of transfer to the adoptive parents before 7 years, and age at death was restricted to 16 to 70 years. The results showed a higher mortality among adoptees, whose biological parents died in the age range of 16 to 70 years; this was significant for deaths from natural causes, vascular causes and all causes. No influence was seen from early death of adoptive parents, regardless of cause of death. (c) 2005 Wiley-Liss, Inc.

Food additives: an ethical evaluation.

Science.gov (United States)

Mepham, Ben

2011-01-01

Food additives are an integral part of the modern food system, but opinion polls showing most Europeans have worries about them imply an urgent need for ethical analysis of their use. The existing literature on food ethics, safety assessment and animal testing. Food additives provide certain advantages in terms of many people's lifestyles. There are disagreements about the appropriate application of the precautionary principle and of the value and ethical validity of animal tests in assessing human safety. Most consumers have a poor understanding of the relative benefits and risks of additives, but concerns over food safety and animal testing remain high. Examining the impacts of food additives on consumer sovereignty, consumer health and on animals used in safety testing should allow a more informed debate about their appropriate uses.

Implementation of the Realized Genomic Relationship Matrix to Open-Pollinated White Spruce Family Testing for Disentangling Additive from Nonadditive Genetic Effects

Directory of Open Access Journals (Sweden)

Omnia Gamal El-Dien

2016-03-01

Full Text Available The open-pollinated (OP family testing combines the simplest known progeny evaluation and quantitative genetics analyses as candidates’ offspring are assumed to represent independent half-sib families. The accuracy of genetic parameter estimates is often questioned as the assumption of “half-sibling” in OP families may often be violated. We compared the pedigree- vs. marker-based genetic models by analysing 22-yr height and 30-yr wood density for 214 white spruce [Picea glauca (Moench Voss] OP families represented by 1694 individuals growing on one site in Quebec, Canada. Assuming half-sibling, the pedigree-based model was limited to estimating the additive genetic variances which, in turn, were grossly overestimated as they were confounded by very minor dominance and major additive-by-additive epistatic genetic variances. In contrast, the implemented genomic pairwise realized relationship models allowed the disentanglement of additive from all nonadditive factors through genetic variance decomposition. The marker-based models produced more realistic narrow-sense heritability estimates and, for the first time, allowed estimating the dominance and epistatic genetic variances from OP testing. In addition, the genomic models showed better prediction accuracies compared to pedigree models and were able to predict individual breeding values for new individuals from untested families, which was not possible using the pedigree-based model. Clearly, the use of marker-based relationship approach is effective in estimating the quantitative genetic parameters of complex traits even under simple and shallow pedigree structure.

A Sordaria macrospora mutant lacking the leu1 gene shows a developmental arrest during fruiting body formation.

Science.gov (United States)

Kück, Ulrich

2005-10-01

Developmental mutants with defects in fruiting body formation are excellent resources for the identification of genetic components that control cellular differentiation processes in filamentous fungi. The mutant pro4 of the ascomycete Sordaria macrospora is characterized by a developmental arrest during the sexual life cycle. This mutant generates only pre-fruiting bodies (protoperithecia), and is unable to form ascospores. Besides being sterile, pro4 is auxotrophic for leucine. Ascospore analysis revealed that the two phenotypes are genetically linked. After isolation of the wild-type leu1 gene from S. macrospora, complementation experiments demonstrated that the gene was able to restore both prototrophy and fertility in pro4. To investigate the control of leu1 expression, other genes involved in leucine biosynthesis specifically and in the general control of amino acid biosynthesis ("cross-pathway control") have been analysed using Northern hybridization and quantitative RT-PCR. These analyses demonstrated that genes of leucine biosynthesis are transcribed at higher levels under conditions of amino acid starvation. In addition, the expression data for the cpc1 and cpc2 genes indicate that cross-pathway control is superimposed on leucine-specific regulation of fruiting body development in the leu1 mutant. This was further substantiated by growth experiments in which the wild-type strain was found to show a sterile phenotype when grown on a medium containing the amino acid analogue 5-methyl-tryptophan. Taken together, these data show that pro4 represents a novel mutant type in S. macrospora, in which amino acid starvation acts as a signal that interrupts the development of the fruiting body.

The SNS target station preliminary Title I shielding analyses

International Nuclear Information System (INIS)

Johnson, J.O.; Santoro, R.T.; Lillie, R.A.; Barnes, J.M.; McNeilly, G.S.

2000-01-01

The Department of Energy (DOE) has given the Spallation Neutron Source (SNS) project approval to begin Title I design of the proposed facility to be built at Oak Ridge National Laboratory (ORNL). During the conceptual design phase of the SNS project, the target station bulk-biological shield was characterized and the activation of the major targets station components was calculated. Shielding requirements were assessed with respect to weight, space, and dose-rate constraints for operating, shut-down, and accident conditions utilizing the SNS shield design criteria, DOE Order 5480.25, and requirements specified in 10 CFR 835. Since completion of the conceptual design phase, there have been major design changes to the target station as a result of the initial shielding and activation analyses, modifications brought about due to engineering concerns, and feedback from numerous external review committees. These design changes have impacted the results of the conceptual design analyses, and consequently, have required a re-investigation of the new design. Furthermore, the conceptual design shielding analysis did not address many of the details associated with the engineering design of the target station. In this paper, some of the proposed SNS target station preliminary Title I shielding design analyses will be presented. The SNS facility (with emphasis on the target station), shielding design requirements, calculational strategy, and source terms used in the analyses will be described. Preliminary results and conclusions, along with recommendations for additional analyses, will also be presented. (author)

Showing Value (Editorial

Directory of Open Access Journals (Sweden)

Denise Koufogiannakis

2009-06-01

librarians on student achievement. Todd notes, “If we do not show value, we will not have a future. Evidence-based practice is not about the survival of school librarians, it’s about the survival of our students” (40. In this issue we feature school libraries and their connection to evidence based practice. Former Editor-in-Chief, Lindsay Glynn, began putting the wheels in motion for this feature almost a year ago. She invited Carol Gordon and Ross Todd to act as guest editors of the section, drawing upon their contacts and previous work in this field. The result is an issue with five feature articles exploring different aspects of the connection between school libraries and evidence based practice, from the theoretical to the practical. In addition, there is a thought-provoking Commentary by David Loertscher, asking whether we need the evolutionary model of evidence based practice, or something more revolutionary!In addition to the Feature section, we have a well-rounded issue with articles on the topics of library human resources, and the development of a scholars’ portal. As well, there are a record 10 evidence summaries and our educational EBL101 column. I hope there is something for everyone in this issue of EBLIP – enjoy, and see you soon in Stockholm!

Alpha-conotoxin analogs with additional positive charge show increased selectivity towards Torpedo californica and some neuronal subtypes of nicotinic acetylcholine receptors

NARCIS (Netherlands)

Kasheverov, I.E.; Zhmak, M.N.; Vulfius, C.A.; Corbacheva, E.V.; Mordvintsev, D.Y.; Utkin, Y.N.; van Elk, R.; Smit, A.B.; Tsetlin, V.I.

2006-01-01

α-Conotoxins from Conus snails are indispensable tools for distinguishing various subtypes of nicotinic acetylcholine receptors (nAChRs), and synthesis of α-conotoxin analogs may yield novel antagonists of higher potency and selectivity. We incorporated additional positive charges into α-conotoxins

A 67-Item Stress Resilience item bank showing high content validity was developed in a psychosomatic sample.

Science.gov (United States)

Obbarius, Nina; Fischer, Felix; Obbarius, Alexander; Nolte, Sandra; Liegl, Gregor; Rose, Matthias

2018-04-10

To develop the first item bank to measure Stress Resilience (SR) in clinical populations. Qualitative item development resulted in an initial pool of 131 items covering a broad theoretical SR concept. These items were tested in n=521 patients at a psychosomatic outpatient clinic. Exploratory and Confirmatory Factor Analysis (CFA), as well as other state-of-the-art item analyses and IRT were used for item evaluation and calibration of the final item bank. Out of the initial item pool of 131 items, we excluded 64 items (54 factor loading .3, 2 non-discriminative Item Response Curves, 4 Differential Item Functioning). The final set of 67 items indicated sufficient model fit in CFA and IRT analyses. Additionally, a 10-item short form with high measurement precision (SE≤.32 in a theta range between -1.8 and +1.5) was derived. Both the SR item bank and the SR short form were highly correlated with an existing static legacy tool (Connor-Davidson Resilience Scale). The final SR item bank and 10-item short form showed good psychometric properties. When further validated, they will be ready to be used within a framework of Computer-Adaptive Tests for a comprehensive assessment of the Stress-Construct. Copyright © 2018. Published by Elsevier Inc.

Towards interoperable and reproducible QSAR analyses: Exchange of datasets.

Science.gov (United States)

Spjuth, Ola; Willighagen, Egon L; Guha, Rajarshi; Eklund, Martin; Wikberg, Jarl Es

2010-06-30

QSAR is a widely used method to relate chemical structures to responses or properties based on experimental observations. Much effort has been made to evaluate and validate the statistical modeling in QSAR, but these analyses treat the dataset as fixed. An overlooked but highly important issue is the validation of the setup of the dataset, which comprises addition of chemical structures as well as selection of descriptors and software implementations prior to calculations. This process is hampered by the lack of standards and exchange formats in the field, making it virtually impossible to reproduce and validate analyses and drastically constrain collaborations and re-use of data. We present a step towards standardizing QSAR analyses by defining interoperable and reproducible QSAR datasets, consisting of an open XML format (QSAR-ML) which builds on an open and extensible descriptor ontology. The ontology provides an extensible way of uniquely defining descriptors for use in QSAR experiments, and the exchange format supports multiple versioned implementations of these descriptors. Hence, a dataset described by QSAR-ML makes its setup completely reproducible. We also provide a reference implementation as a set of plugins for Bioclipse which simplifies setup of QSAR datasets, and allows for exporting in QSAR-ML as well as old-fashioned CSV formats. The implementation facilitates addition of new descriptor implementations from locally installed software and remote Web services; the latter is demonstrated with REST and XMPP Web services. Standardized QSAR datasets open up new ways to store, query, and exchange data for subsequent analyses. QSAR-ML supports completely reproducible creation of datasets, solving the problems of defining which software components were used and their versions, and the descriptor ontology eliminates confusions regarding descriptors by defining them crisply. This makes is easy to join, extend, combine datasets and hence work collectively, but

Towards interoperable and reproducible QSAR analyses: Exchange of datasets

Directory of Open Access Journals (Sweden)

Spjuth Ola

2010-06-01

Full Text Available Abstract Background QSAR is a widely used method to relate chemical structures to responses or properties based on experimental observations. Much effort has been made to evaluate and validate the statistical modeling in QSAR, but these analyses treat the dataset as fixed. An overlooked but highly important issue is the validation of the setup of the dataset, which comprises addition of chemical structures as well as selection of descriptors and software implementations prior to calculations. This process is hampered by the lack of standards and exchange formats in the field, making it virtually impossible to reproduce and validate analyses and drastically constrain collaborations and re-use of data. Results We present a step towards standardizing QSAR analyses by defining interoperable and reproducible QSAR datasets, consisting of an open XML format (QSAR-ML which builds on an open and extensible descriptor ontology. The ontology provides an extensible way of uniquely defining descriptors for use in QSAR experiments, and the exchange format supports multiple versioned implementations of these descriptors. Hence, a dataset described by QSAR-ML makes its setup completely reproducible. We also provide a reference implementation as a set of plugins for Bioclipse which simplifies setup of QSAR datasets, and allows for exporting in QSAR-ML as well as old-fashioned CSV formats. The implementation facilitates addition of new descriptor implementations from locally installed software and remote Web services; the latter is demonstrated with REST and XMPP Web services. Conclusions Standardized QSAR datasets open up new ways to store, query, and exchange data for subsequent analyses. QSAR-ML supports completely reproducible creation of datasets, solving the problems of defining which software components were used and their versions, and the descriptor ontology eliminates confusions regarding descriptors by defining them crisply. This makes is easy to join

Additive effects of word frequency and stimulus quality: the influence of trial history and data transformations.

Science.gov (United States)

Balota, David A; Aschenbrenner, Andrew J; Yap, Melvin J

2013-09-01

A counterintuitive and theoretically important pattern of results in the visual word recognition literature is that both word frequency and stimulus quality produce large but additive effects in lexical decision performance. The additive nature of these effects has recently been called into question by Masson and Kliegl (in press), who used linear mixed effects modeling to provide evidence that the additive effects were actually being driven by previous trial history. Because Masson and Kliegl also included semantic priming as a factor in their study and recent evidence has shown that semantic priming can moderate the additivity of word frequency and stimulus quality (Scaltritti, Balota, & Peressotti, 2012), we reanalyzed data from 3 published studies to determine if previous trial history moderated the additive pattern when semantic priming was not also manipulated. The results indicated that previous trial history did not influence the joint influence of word frequency and stimulus quality. More important, and independent of Masson and Kliegl's conclusions, we also show how a common transformation used in linear mixed effects analyses to normalize the residuals can systematically alter the way in which two variables combine to influence performance. Specifically, using transformed, rather than raw reaction times, consistently produces more underadditive patterns. PsycINFO Database Record (c) 2013 APA, all rights reserved.

Passive safety injection experiments and analyses (PAHKO)

International Nuclear Information System (INIS)

Tuunanen, J.

1998-01-01

PAHKO project involved experiments on the PACTEL facility and computer simulations of selected experiments. The experiments focused on the performance of Passive Safety Injection Systems (PSIS) of Advanced Light Water Reactors (ALWRs) in Small Break Loss-Of-Coolant Accident (SBLOCA) conditions. The PSIS consisted of a Core Make-up Tank (CMT) and two pipelines (Pressure Balancing Line, PBL, and Injection Line, IL). The examined PSIS worked efficiently in SBLOCAs although the flow through the PSIS stopped temporarily if the break was very small and the hot water filled the CMT. The experiments demonstrated the importance of the flow distributor in the CMT to limit rapid condensation. The project included validation of three thermal-hydraulic computer codes (APROS, CATHARE and RELAP5). The analyses showed the codes are capable to simulate the overall behaviour of the transients. The detailed analyses of the results showed some models in the codes still need improvements. Especially, further development of models for thermal stratification, condensation and natural circulation flow with small driving forces would be necessary for accurate simulation of the PSIS phenomena. (orig.)

Progranulin shows cytoprotective effects on trophoblast cells in vitro but does not antagonize TNF-α-induced apoptosis.

Science.gov (United States)

Stubert, Johannes; Waldmann, Kathrin; Dieterich, Max; Richter, Dagmar-Ulrike; Briese, Volker

2014-11-01

The glycoprotein progranulin directly binds to TNF-receptors and thereby can antagonize the inflammatory effects of TNF-α. Here we analyzed the impact of both cytokines on cytotoxicity and viability of trophoblast cells. Isolated villous first trimester human trophoblast cells and the human choriocarcinoma cell line BeWo were treated with recombinant human progranulin and TNF-α. Analyses were performed by LDH- and MTT-assay and measurement of caspase-8-activity. Progranulin treatment showed some cytoprotective effects on isolated trophoblast cells. However, TNF-α-induced apoptosis was not antagonized by addition of progranulin. Effects were similar, but more pronounced in BeWo cells. The cytoprotective activity of progranulin on trophoblast cells in vitro was only weak and of doubtful biologic relevance. It was not able to antagonize TNF-α. Future studies should focus on possible paracrine activities of progranulin.

The impact of multiple show-ups on eyewitness decision-making and innocence risk.

Science.gov (United States)

Smith, Andrew M; Bertrand, Michelle; Lindsay, R C L; Kalmet, Natalie; Grossman, Deborah; Provenzano, Daniel

2014-09-01

If an eyewitness rejects a show-up, police may respond by finding a new suspect and conducting a second show-up with the same eyewitness. Police may continue finding suspects and conducting show-ups until the eyewitness makes an identification (Study 1). Relatively low criterion-setting eyewitnesses filter themselves out of the multiple show-ups procedure by choosing the first suspect with whom they are presented (Studies 2 and 3). Accordingly, response bias was more stringent on the second show-up when compared with the first, but became no more stringent with additional show-ups. Despite this stringent shift in response bias, innocence risk increased with additional show-ups, as false alarms cumulate (Studies 2 and 3). Although unbiased show-up instructions decreased innocent suspect identifications, the numbers were still discouraging (Study 4). Given the high number of innocent suspects who would be mistakenly identified through the use of multiple show-up procedures, using such identifications as evidence of guilt is questionable. Although evidence of guilt is limited to identifications from a single show-up, practical constraints might sometimes require police to use additional show-ups. Accordingly, we propose a stronger partition between evidentiary and investigative procedures. PsycINFO Database Record (c) 2014 APA, all rights reserved.

Data driven polypharmacological drug design for lung cancer: analyses for targeting ALK, MET, and EGFR

DEFF Research Database (Denmark)

Narayanan, Dilip; Gani, Osman ABSM; Gruber, Franz XE

2017-01-01

encoded into molecular mechanics force fields. Cheminformatics analyses of binding data show EGFR to be dissimilar to ALK and MET, but its structure shows how it may be co-targeted with the addition of a covalent trap. This suggests a strategy for the design of a focussed chemical library based on a pan......Drug design of protein kinase inhibitors is now greatly enabled by thousands of publicly available X-ray structures, extensive ligand binding data, and optimized scaffolds coming off patent. The extensive data begin to enable design against a spectrum of targets (polypharmacology); however...... consider polypharmacological targeting of protein kinases ALK, MET, and EGFR (and its drug resistant mutant T790M) in non small cell lung cancer as an example. Both EGFR and ALK represent sources of primary oncogenic lesions, while drug resistance arises from MET amplification and EGFR mutation. A drug...

Nonlinear analyses of spent-fuel racks for consolidated fuel loading

International Nuclear Information System (INIS)

Kabir, A.F.; Godha, P.C.; Malik, L.E.; Bolourchi, S.

1987-01-01

Storage racks for spent-fuel assemblies in nuclear power plants are designed to withstand various combinations of loads generated by gravity, seismic, thermal, and accidental fuel drops. Due to the need for storing increased amounts of spent fuel in the existing fuel pools, many nuclear power utilities are evaluating existing fuel racks to safely carry the additional loads. The current study presents the seismic analyses of existing fuel racks of Northeast Utility Company's Millstone Unit Number 1 (BWR Mark I) nuclear plant to accommodate a 2:1 fuel consolidation. This objective requires rigorous nonlinear analyses to establish the full available capacities of the racks and thereby avoid expensive modifications or minimize any needed upgrades

Simulation-based Investigations of Electrostatic Beam Energy Analysers

CERN Document Server

Pahl, Hannes

2015-01-01

An energy analyser is needed to measure the beam energy profile behind the REX-EBIS at ISOLDE. The device should be able to operate with an accuracy of 1 V at voltages up to 30 kV. In order to find a working concept for an electrostatic energy analyser different designs were evaluated with simulations. A spherical device and its design issues are presented. The potential deformation effects of grids at high voltages and their influence on the energy resolution were investigated. First tests were made with a grid-free ring electrode device and show promising results.

Analysing Trust Transitivity and The Effects of Unknown Dependence

Directory of Open Access Journals (Sweden)

Touhid Bhuiyan

2010-03-01

Full Text Available Trust can be used to improve online automated recommendation within a given domain. Trust transitivity is used to make it successful. But trust transitivity has different interpretations. Trust and trust transitivity; both are the human mental phenomenon and for this reason, there is no such thing as objective transitivity. Trust transitivity and trust fusion both are important elements in computational trust. This paper analyses the parameter dependence problem in trust transitivity and proposes some definitions considering the effects of base rate. In addition, it also proposes belief functions based on subjective logic to analyse trust transitivity of three specified cases with sensitive and insensitive based rate. Then it presents a quantitative analysis of the effects of unknown dependence problem in an interconnected network environment; such Internet.

Flame Retardant Polyamide Fibres: The Challenge of Minimising Flame Retardant Additive Contents with Added Nanoclays

Directory of Open Access Journals (Sweden)

Richard Horrocks

2016-08-01

Full Text Available This work shows that halogen-free, flame retarded polyamide 6 (PA6, fabrics may be produced in which component fibres still have acceptable tensile properties and low levels (preferably ≤10 wt % of additives by incorporating a nanoclay along with two types of flame retardant formulations. The latter include (i aluminium diethyl phosphinate (AlPi at 10 wt %, known to work principally in the vapour phase and (ii ammonium sulphamate (AS/dipentaerythritol (DP system present at 2.5 and 1 wt % respectively, believed to be condense phase active. The nanoclay chosen is an organically modified montmorillonite clay, Cloisite 25A. The effect of each additive system is analysed in terms of its ability to maximise both filament tensile properties relative to 100% PA6 and flame retardant behaviour of knitted fabrics in a vertical orientation. None of the AlPi-containing formulations achieved self-extinguishability, although the presence of nanoclay promoted lower burning and melt dripping rates. The AS/DP-containing formulations with total flame retardant levels of 5.5 wt % or less showed far superior properties and with nanoclay, showed fabric extinction times ≤ 39 s and reduced melt dripping. The tensile and flammability results, supported by thermogravimetric analysis, have been interpreted in terms of the mechanism of action of each flame retardant/nanoclay type.

Gene expression profiling in colon of mice exposed to food additive titanium dioxide (E171).

Science.gov (United States)

Proquin, Héloïse; Jetten, Marlon J; Jonkhout, Marloes C M; Garduño-Balderas, Luis G; Briedé, Jacob J; de Kok, Theo M; Chirino, Yolanda I; van Loveren, Henk

2018-01-01

Dietary factors that may influence the risks of colorectal cancer, including specific supplements, are under investigation. Previous studies showed the capacity of food additive titanium dioxide (E171) to induce DNA damage in vitro and facilitate growth of colorectal tumours in vivo. This study aimed to investigate the molecular mechanisms behind these effects after E171 exposure. BALB/c mice were exposed by gavage to 5 mg/kg bw /day of E171 for 2, 7, 14, and 21 days. Transcriptome changes were studied by whole genome mRNA microarray analysis on the mice's distal colons. In addition, histopathological changes as well as a proliferation marker were analysed. The results showed significant gene expression changes in the olfactory/GPCR receptor family, oxidative stress, the immune system and of cancer related genes. Transcriptome analysis also identified genes that thus far have not been included in known biological pathways and can induce functional changes by interacting with other genes involved in different biological pathways. Histopathological analysis showed alteration and disruption in the normal structure of crypts inducing a hyperplastic epithelium. At cell proliferation level, no consistent increase over time was observed. These results may offer a mechanistic framework for the enhanced tumour growth after ingestion of E171 in BALB/c mice. Copyright © 2017 Elsevier Ltd. All rights reserved.

Special analyses reveal coke-deposit structure

International Nuclear Information System (INIS)

Albright, L.F.

1988-01-01

A scanning electron microscope (SEM) and an energy dispersive X-ray analyzer (EDAX) have been used to obtain information that clarifies the three mechanisms of coke formation in ethylene furnaces, and to analyze the metal condition at the exit of furnace. The results can be used to examine furnace operations and develop improved ethylene plant practices. In this first of four articles on the analyses of coke and metal samples, the coking mechanisms and coke deposits in a section of tube from an actual ethylene furnace (Furnace A) from a plant on the Texas Gulf Coast are discussed. The second articles in the series will analyze the condition of the tube metal in the same furnace. To show how coke deposition and metal condition dependent on the operating parameters of an ethylene furnace, the third article in the series will show the coke deposition in a Texas Gulf Coast furnace tube (Furnace B) that operated at shorter residence time. The fourth article discusses the metal condition in that furnace. Some recommendations, based on the analyses and findings, are offered in the fourth article that could help extend the life of ethylene furnace tubes, and also improve overall ethylene plant operations

Effect of sodium azide addition and aging storage on casein micelle size

Science.gov (United States)

Sinaga, H.; Deeth, H.; Bhandari, B.

2018-02-01

Casein micelles affected most of milk properties, therefore the use sodium azide as milk preservation is not expected to alter milk properties during storage, including the casein micelle size. The aim of this study was to analyse casein micelle size after the addition of sodium azide during storage. The experiment was performed as a complete block randomised design with three replications. The addition of 0.02-0.10% Na-azide do not lead to any noticeable differences in average casein size at the same day and show similar trend after 14 day-storage. At concentration of 0.02% sodium azide (Na-azide), the size of pasteurised milk did not change up to 12 days, while the size of raw skim milk slightly increased by ageing time at day 5. The treated concentration did not affect the size distribution, except for milk with 0.02% Na-azide which had narrower distribution compared to other treated and control milk. The finding from this study suggests that the role of Na-azide in this experiments during storage at 4°C is only for preventing the microbial growth.

Additional 5 kWe thermoelectric system temperature transients

International Nuclear Information System (INIS)

Halfen, F.J.

1972-01-01

Several additional system transients have been calculated for the 5 kW(e) TE system and are reported in this document. They include a startup transient with a reactivity rate of 0.005 cents/sec, several startup accidents, a step reactivity insertion at full power and a loss of electrical load. These data are intended for input to system design analyses and for possible use in the protected accident section of the safety report. (U.S.)

Mitigation of Humic Acid Inhibition in Anaerobic Digestion of Cellulose by Addition of Various Salts

Directory of Open Access Journals (Sweden)

Samet Azman

2015-03-01

Full Text Available Humic compounds are inhibitory to the anaerobic hydrolysis of cellulosic biomass. In this study, the impact of salt addition to mitigate the inhibitory effects of humic compounds was investigated. The experiment was conducted using batch tests to monitor the anaerobic hydrolysis of cellulose in the presence of humic acid. Sodium, potassium, calcium, magnesium and iron salts were tested separately for their efficiency to mitigate humic acid inhibition. All experiments were done under mesophilic conditions (30 °C and at pH 7. Methane production was monitored online, using the Automatic Methane Potential Test System. Methane production, soluble chemical oxygen demand and volatile fatty acid content of the samples were measured to calculate the hydrolysis efficiencies. Addition of magnesium, calcium and iron salts clearly mitigated the inhibitory effects of humic acid and hydrolysis efficiencies reached up to 75%, 65% and 72%, respectively, which were similar to control experiments. Conversely, potassium and sodium salts addition did not mitigate the inhibition and hydrolysis efficiencies were found to be less than 40%. Mitigation of humic acid inhibition via salt addition was also validated by inductively coupled plasma atomic emission spectroscopy analyses, which showed the binding capacity of different cations to humic acid.

Drag reduction by natural polymeric additives in PMDS microchannel: Effect of types of additives

Directory of Open Access Journals (Sweden)

Ling Fiona W.M.

2017-01-01

Full Text Available Drag reduction technology was used in medical applications to enhance the blood flow in semiclogged blood streams which can be an alternative treatment for atherosclerosis. In this present study, natural polymeric drag reducing additives (DRA was introduced to replace synthetic polymer which has the possibility of bringing side effects to human health. Three different sources, namely okra, aloe vera and hibiscus were utilized to extract the natural polymeric additives which were then tested in custom made microchannel simulating human heart blood vessels. The performance of different types of additives was evaluated using pressure measurements. The maximum drag reduction up to 63.48% is achieved using 300 ppm of hibiscus mucilage at operating pressure of 50 mbar. In this present work, hibiscus showed the best drag reduction performance, giving the highest %FI in most of the cases. This experimental results proved that these natural polymeric additives could be utilized as DRA in enhancing the blood flow in semiclogged blood streams.

Phytoplankton growth response to Asian dust addition in the northwest Pacific Ocean versus the Yellow Sea

Science.gov (United States)

Zhang, Chao; Gao, Huiwang; Yao, Xiaohong; Shi, Zongbo; Shi, Jinhui; Yu, Yang; Meng, Ling; Guo, Xinyu

2018-02-01

In this study, five on-board microcosm experiments were performed in the subtropical gyre, the Kuroshio Extension region of the northwest Pacific Ocean (NWPO), and the Yellow Sea (YS) in order to investigate phytoplankton growth following the addition of artificially modified mineral dust (AM dust) and various nutrients (nitrogen (N), phosphorus (P), iron (Fe), N + P, and N + P + Fe). The two experiments carried out with AM-dust addition in the subtropical gyre showed a maximum chlorophyll a (Chl a) concentration increase of 1.7- and 2.8-fold, while the cell abundance of large-sized phytoplankton ( > 5 µm) showed a 1.8- and 3.9-fold increase, respectively, relative to the controls. However, in the Kuroshio Extension region and the YS, the increases in maximum Chl a and cell abundance of large-sized phytoplankton following AM-dust addition were at most 1.3-fold and 1.7-fold larger than those in the controls, respectively. A net conversion efficiency index (NCEI) newly proposed in this study, size-fractionated Chl a, and the abundance of large-sized phytoplankton were analysed to determine which nutrients contribute to supporting phytoplankton growth. Our results demonstrate that a combination of nutrients, N-P or N + P + Fe, is responsible for phytoplankton growth in the subtropical gyre following AM-dust addition. Single nutrient addition, i.e., N in the Kuroshio Extension region and P or N in the YS, controls the phytoplankton growth following AM-dust addition. In the AM-dust-addition experiments, in which the increased N-P or P was identified to determine phytoplankton growth, the dissolved inorganic P from AM dust (8.6 nmol L-1) was much lower than the theoretically estimated minimum P demand (˜ 20 nmol L-1) for phytoplankton growth. These observations suggest that additional supply augments the bioavailable P stock in incubated seawater with AM-dust addition, most likely due to an enhanced solubility of P from AM dust or the remineralization of the dissolved

Evidence of a major gene from Bayesian segregation analyses of liability to osteochondral diseases in pigs.

Science.gov (United States)

Kadarmideen, Haja N; Janss, Luc L G

2005-11-01

Bayesian segregation analyses were used to investigate the mode of inheritance of osteochondral lesions (osteochondrosis, OC) in pigs. Data consisted of 1163 animals with OC and their pedigrees included 2891 animals. Mixed-inheritance threshold models (MITM) and several variants of MITM, in conjunction with Markov chain Monte Carlo methods, were developed for the analysis of these (categorical) data. Results showed major genes with significant and substantially higher variances (range 1.384-37.81), compared to the polygenic variance (sigmau2). Consequently, heritabilities for a mixed inheritance (range 0.65-0.90) were much higher than the heritabilities from the polygenes. Disease allele frequencies range was 0.38-0.88. Additional analyses estimating the transmission probabilities of the major gene showed clear evidence for Mendelian segregation of a major gene affecting osteochondrosis. The variants, MITM with informative prior on sigmau2, showed significant improvement in marginal distributions and accuracy of parameters. MITM with a "reduced polygenic model" for parameterization of polygenic effects avoided convergence problems and poor mixing encountered in an "individual polygenic model." In all cases, "shrinkage estimators" for fixed effects avoided unidentifiability for these parameters. The mixed-inheritance linear model (MILM) was also applied to all OC lesions and compared with the MITM. This is the first study to report evidence of major genes for osteochondral lesions in pigs; these results may also form a basis for underpinning the genetic inheritance of this disease in other animals as well as in humans.

Higher- and Lower-Order Factor Analyses of the Temperament in Middle Childhood Questionnaire

Science.gov (United States)

Kotelnikova, Yuliya; Olino, Thomas M.; Klein, Daniel N.; Mackrell, Sarah V.M.; Hayden, Elizabeth P.

2017-01-01

The Temperament in Middle Childhood Questionnaire (TMCQ; Simonds & Rothbart, 2004) is a widely used parent-report measure of temperament. However, neither its lower- nor higher-order structures have been tested via a bottom-up, empirically based approach. We conducted higher- and lower-order exploratory factor analyses (EFAs) of the TMCQ in a large (N = 654) sample of 9-year-olds. Item-level EFAs identified 92 items as suitable (i.e., with loadings ≥.40) for constructing lower-order factors, only half of which resembled a TMCQ scale posited by the measure’s authors. Higher-order EFAs of the lower-order factors showed that a three-factor structure (Impulsivity/Negative Affectivity, Negative Affectivity, and Openness/Assertiveness) was the only admissible solution. Overall, many TMCQ items did not load well onto a lower-order factor. In addition, only three factors, which did not show a clear resemblance to Rothbart’s four-factor model of temperament in middle childhood, were needed to account for the higher-order structure of the TMCQ. PMID:27002124

[Cost-Effectiveness and Cost-Utility Analyses of Antireflux Medicine].

Science.gov (United States)

Gockel, Ines; Lange, Undine Gabriele; Schürmann, Olaf; Jansen-Winkeln, Boris; Sibbel, Rainer; Lyros, Orestis; von Dercks, Nikolaus

2018-04-12

Laparoscopic antireflux surgery and medical therapy with proton pump inhibitors are gold standards of gastroesophageal reflux treatment. On account of limited resources and increasing healthcare needs and costs, in this analysis, not only optimal medical results, but also superiority in health economics of these 2 methods are evaluated. We performed an electronic literature survey in MEDLINE, PubMed, Cochrane Library, ISRCTN (International Standard Randomization Controlled Trial Number) as well as in the NHS Economic Evaluation Database, including studies published until 1/2017. Only studies considering the effect size of QALY (Quality-Adjusted Life Years) (with respect to different quality of life-scores) as primary outcome comparing laparoscopic fundoplication and medical therapy were included. Criteria of comparison were ICER (Incremental Cost-Effectiveness Ratio) and ICUR (Incremental Cost-Utility Ratio). Superiority of the respective treatment option for each publication was worked out. In total, 18 comparative studies were identified in the current literature with respect to above-mentioned search terms, qualifying for the defined inclusion criteria. Six studies were finally selected for analyses. Out of 6 publications, 3 showed superiority of laparoscopic fundoplication over long-term medical management based on current cost-effectiveness data. Limitations were related to different time intervals, levels of evidence of studies and underlying resources/costs of analyses, healthcare systems and applied quality of life instruments. Future prospective, randomized trials should examine this comparison in greater detail. Additionally, there is a large potential for further research in the health economics assessment of early diagnosis and prevention measures of reflux disease and Barrett's esophagus/carcinoma. © Georg Thieme Verlag KG Stuttgart · New York.

Effect Of Additive Solar Oil On High Temperature Corrosion Resistance Of Diesel Machines

International Nuclear Information System (INIS)

Dani, Mohammad; H, Bagyo; Minsyahril, B.

2004-01-01

It has been done the study of thermal gravimetric analyse (TGA) accompanied with magnetic suspension balance (MSB) on the diesel machine of sample A (HV = 256.78 kgf/mm 2 , ρ = 6.65-7.16 g/cm 3 ) and sample B (HV 166.67 kgf/mm 2 , ρ= 5.39-5.57 g/cm 3 ). The samples were oxidized at 900 o C for 24 hours in the variation of with and without additives (Diesel Booster + Amylum Nitrate; DBANI and Diesel Booster;DB) in solar oil of 1: 1500. The samples were, then, characterized by X-Ray Diffraction (crystal structures) and Scanning Electron Microscope (microstructures). The result shows that the Fe 2 O 3 layers spread out over the sample surfaces and the oxidant grain boundaries are very compacted

ExSTA: External Standard Addition Method for Accurate High-Throughput Quantitation in Targeted Proteomics Experiments.

Science.gov (United States)

Mohammed, Yassene; Pan, Jingxi; Zhang, Suping; Han, Jun; Borchers, Christoph H

2018-03-01

Targeted proteomics using MRM with stable-isotope-labeled internal-standard (SIS) peptides is the current method of choice for protein quantitation in complex biological matrices. Better quantitation can be achieved with the internal standard-addition method, where successive increments of synthesized natural form (NAT) of the endogenous analyte are added to each sample, a response curve is generated, and the endogenous concentration is determined at the x-intercept. Internal NAT-addition, however, requires multiple analyses of each sample, resulting in increased sample consumption and analysis time. To compare the following three methods, an MRM assay for 34 high-to-moderate abundance human plasma proteins is used: classical internal SIS-addition, internal NAT-addition, and external NAT-addition-generated in buffer using NAT and SIS peptides. Using endogenous-free chicken plasma, the accuracy is also evaluated. The internal NAT-addition outperforms the other two in precision and accuracy. However, the curves derived by internal vs. external NAT-addition differ by only ≈3.8% in slope, providing comparable accuracies and precision with good CV values. While the internal NAT-addition method may be "ideal", this new external NAT-addition can be used to determine the concentration of high-to-moderate abundance endogenous plasma proteins, providing a robust and cost-effective alternative for clinical analyses or other high-throughput applications. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

PRACTICE OF DEVELOPMENT OF STUDENTS’ ADDITIONAL INTERDISCIPLINARY COMPETENCIES IN A MODERN UNIVERSITY

Directory of Open Access Journals (Sweden)

E. G. Syryamkina

2016-01-01

Full Text Available The aim of the article is to show the possibilities of formation ofnew approaches to the development of additional interdisciplinary competencies of university youth in modern conditions.Methods. The methods involve such theoretical methods as analysis of scientific literature and documents, generalization of empirical data.Results and scientific novelty. The article includes experience of many years in the sphere of development of students’ additional interdisciplinary competencies of the National Research Tomsk State University (TSU. The authors present cases of two TSU structural subdivisions: Center for Social and Professional Volunteering and Park of Social and Humanitarian Technologies. The effective educational technologies proposed by the authors are analysed. Transition from the theoretical (knowledge training of students to practically-oriented training is an actual trend today. A graduate of a modern university should have a broad vision, communication skills, desire for cooperation, self-development, creative application of gained knowledge and lifelong learning, in other words –the development of students’ additional interdisciplinary competencies. In this regard, the role of students’ extracurricular practical work in a university is increasing. This work requires organizational and educational support. The article gives description and analysis of effective educational forms of technologies for development of students’ additional interdisciplinary competencies within their extracurricular activities in the mentioned above structural units of the university.Practical significance. Higher educational establishments can use presented materials for improvement of an educational process.

Analyses of systems availability and operator actions to support the development of severe accident procedures

International Nuclear Information System (INIS)

Lutz, R.J. Jr.; Scobel, J.H.

1989-01-01

This paper reports on traditional analyses of severe accidents, such as those presented in Probabilistic Risk Assessment (PRA) studies of nuclear power stations, that have generally been performed on the assumption that all means of cooling the reactor core are lost and that no operator actions to mitigate the consequences or progression of the severe accident are performed. The assumption to neglect the availability of safety systems and operator actions which do not prevent core melting can lead to erroneous conclusions regarding the plant severer accident profile. Recent work in severe accident management has identified the need to perform analyses which consider all systems availabilities and operator actions, irrespective of their contribution to the prevention of core melting. These new analyses indicate that the traditional analyses result in overfly pessimistic predictions of the time of core melting and the subsequent potential for recovery of core cooling prior to core melting. Additionally, since the traditional analyses do not model all of the operator actions which are prescribed, the impact of additional severe accident operator actions on the progression and consequences of the accident cannot be reliably identified. Further, the more detailed analysis can change the focus of the importance of various system to the prevention of core damage and the mitigation of severe accident consequences. Finally, the simplicity of the traditional analyses can have a considerable impact on severe accident decision making, particularly in the evaluation of alternate plant design features and the priorities for research studies

A comparison of cephalometric analyses for assessing sagittal jaw relationship

International Nuclear Information System (INIS)

Erum, G.; Fida, M.

2008-01-01

To compare the seven methods of cephalometric analysis for assessing sagittal jaw relationship and to determine the level of agreement between them. Seven methods, describing anteroposterior jaw relationships (A-B plane, ANB, Wits, AXB, AF-BF, FABA and Beta angle) were measured on the lateral cephalographs of 85 patients. Correlation analysis, using Cramer's V-test, was performed to determine the possible agreement between the pair of analyses. The mean age of the sample, comprising 35 males and 50 females was 15 years and 3 months. Statistically significant relationships were found among seven sagittal parameters with p-value <0.001. Very strong correlation was found between AXB and AF-BF distance (r=0.924); and weak correlation between ANB and Beta angle (r=0.377). Wits appraisal showed the greatest coefficient of variability. Despite varying strengths of association, statistically significant correlations were found among seven methods for assessing sagittal jaw relationship. FABA and A-B plane may be used to predict the skeletal class in addition to the established ANB angle. (author)

Show me the money: incorporating financial motives into the gambling motives questionnaire.

Science.gov (United States)

Dechant, Kristianne

2014-12-01

Although research has only recently begun to measure what motivates all levels of gambling involvement, motives could offer a theoretically interesting and practical way to subtype gamblers in research and for responsible gambling initiatives. The Gambling Motives Questionnaire (GMQ) is one measure that weaves together much of the gambling motives literature, but it has been criticized for neglecting financial reasons for gambling. This study uses a series of factor analyses to explore the effect of adding nine financial motives to the GMQ in a heterogeneous sample of 1,014 adult past-year gamblers. After trimming trivial financial motives, the penultimate factor analysis of the 15 GMQ items and four financial motives led to a four-factor solution, with factors tapping enhancement, social, coping and financial motives, as predicted. A final factor analysis performed on a modified GMQ-F (i.e., 16 items, including a financial subscale) revealed the same four factors, and hierarchical regression showed that the financial motives improve the GMQ-F's prediction of gambling frequency. This study provides evidence that omitting financial motives is a clear gap in the GMQ, yet suggests that the GMQ is a promising tool that can be conceptually and empirically strengthened with the simple addition of financial items.

Dissection of additive, dominance, and imprinting effects for production and reproduction traits in Holstein cattle.

Science.gov (United States)

Jiang, Jicai; Shen, Botong; O'Connell, Jeffrey R; VanRaden, Paul M; Cole, John B; Ma, Li

2017-05-30

Although genome-wide association and genomic selection studies have primarily focused on additive effects, dominance and imprinting effects play an important role in mammalian biology and development. The degree to which these non-additive genetic effects contribute to phenotypic variation and whether QTL acting in a non-additive manner can be detected in genetic association studies remain controversial. To empirically answer these questions, we analyzed a large cattle dataset that consisted of 42,701 genotyped Holstein cows with genotyped parents and phenotypic records for eight production and reproduction traits. SNP genotypes were phased in pedigree to determine the parent-of-origin of alleles, and a three-component GREML was applied to obtain variance decomposition for additive, dominance, and imprinting effects. The results showed a significant non-zero contribution from dominance to production traits but not to reproduction traits. Imprinting effects significantly contributed to both production and reproduction traits. Interestingly, imprinting effects contributed more to reproduction traits than to production traits. Using GWAS and imputation-based fine-mapping analyses, we identified and validated a dominance association signal with milk yield near RUNX2, a candidate gene that has been associated with milk production in mice. When adding non-additive effects into the prediction models, however, we observed little or no increase in prediction accuracy for the eight traits analyzed. Collectively, our results suggested that non-additive effects contributed a non-negligible amount (more for reproduction traits) to the total genetic variance of complex traits in cattle, and detection of QTLs with non-additive effect is possible in GWAS using a large dataset.

Uncertainty Analyses and Strategy

International Nuclear Information System (INIS)

Kevin Coppersmith

2001-01-01

performance difficult. Likewise, a demonstration of the magnitude of conservatisms in the dose estimates that result from conservative inputs is difficult to determine. To respond to these issues, the DOE explored the significance of uncertainties and the magnitude of conservatisms in the SSPA Volumes 1 and 2 (BSC 2001 [DIRS 155950]; BSC 2001 [DIRS 154659]). The three main goals of this report are: (1) To briefly summarize and consolidate the discussion of much of the work that has been done over the past few years to evaluate, clarify, and improve the representation of uncertainties in the TSPA and performance projections for a potential repository. This report does not contain any new analyses of those uncertainties, but it summarizes in one place the main findings of that work. (2) To develop a strategy for how uncertainties may be handled in the TSPA and supporting analyses and models to support a License Application, should the site be recommended. It should be noted that the strategy outlined in this report is based on current information available to DOE. The strategy may be modified pending receipt of additional pertinent information, such as the Yucca Mountain Review Plan. (3) To discuss issues related to communication about uncertainties, and propose some approaches the DOE may use in the future to improve how it communicates uncertainty in its models and performance assessments to decision-makers and to technical audiences

Influence of lead oxide addition on LnTiTaO6 (Ln = Ce, Pr and Nd ...

Indian Academy of Sciences (India)

The crystal structure of the materials was analysed using X-ray diffraction techniques and the sur- face morphology of the sintered samples was analysed using scanning electron microscopy. The dielectric constant at microwave frequency range decreases for higher PbO addition for all the samples but the quality factor ...

Contour plot assessment of existing meta-analyses confirms robust association of statin use and acute kidney injury risk.

Science.gov (United States)

Chevance, Aurélie; Schuster, Tibor; Steele, Russell; Ternès, Nils; Platt, Robert W

2015-10-01

Robustness of an existing meta-analysis can justify decisions on whether to conduct an additional study addressing the same research question. We illustrate the graphical assessment of the potential impact of an additional study on an existing meta-analysis using published data on statin use and the risk of acute kidney injury. A previously proposed graphical augmentation approach is used to assess the sensitivity of the current test and heterogeneity statistics extracted from existing meta-analysis data. In addition, we extended the graphical augmentation approach to assess potential changes in the pooled effect estimate after updating a current meta-analysis and applied the three graphical contour definitions to data from meta-analyses on statin use and acute kidney injury risk. In the considered example data, the pooled effect estimates and heterogeneity indices demonstrated to be considerably robust to the addition of a future study. Supportingly, for some previously inconclusive meta-analyses, a study update might yield statistically significant kidney injury risk increase associated with higher statin exposure. The illustrated contour approach should become a standard tool for the assessment of the robustness of meta-analyses. It can guide decisions on whether to conduct additional studies addressing a relevant research question. Copyright © 2015 Elsevier Inc. All rights reserved.

Children's patterns of reasoning about reading and addition concepts.

Science.gov (United States)

Farrington-Flint, Lee; Canobi, Katherine H; Wood, Clare; Faulkner, Dorothy

2010-06-01

Children's reasoning was examined within two educational contexts (word reading and addition) so as to understand the factors that contribute to relational reasoning in the two domains. Sixty-seven 5- to 7-year-olds were given a series of related words to read or single-digit addition items to solve (interspersed with unrelated items). The frequency, accuracy, and response times of children's self-reports on the conceptually related items provided a measure of relational reasoning, while performance on the unrelated addition and reading items provided a measure of procedural skill. The results indicated that the children's ability to use conceptual relations to solve both reading and addition problems enhanced speed and accuracy levels, increased with age, and was related to procedural skill. However, regression analyses revealed that domain-specific competencies can best explain the use of conceptual relations in both reading and addition. Moreover, a cluster analysis revealed that children differ according to the academic domain in which they first apply conceptual relations and these differences are related to individual variation in their procedural skills within these particular domains. These results highlight the developmental significance of relational reasoning in the context of reading and addition and underscore the importance of concept-procedure links in explaining children's literacy and arithmetical development.

Integrated Waste Treatment Unit (IWTU) Input Coal Analyses and Off-Gass Filter (OGF) Content Analyses

Energy Technology Data Exchange (ETDEWEB)

Jantzen, Carol M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, David M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Guenther, Chris P. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Shekhawat, Dushyant [National Energy Technology Lab. (NETL), Morgantown, WV (United States); VanEssendelft, Dirk T. [National Energy Technology Lab. (NETL), Morgantown, WV (United States); Means, Nicholas C. [AECOM Technology Corp., Oak Ridge, TN (United States)

2015-04-23

in process piping and materials, in excessive off-gas absorbent loading, and in undesired process emissions. The ash content of the coal is important as the ash adds to the DMR and other vessel products which affect the final waste product mass and composition. The amount and composition of the ash also affects the reaction kinetics. Thus ash content and composition contributes to the mass balance. In addition, sodium, potassium, calcium, sulfur, and maybe silica and alumina in the ash may contribute to wall-scale formation. Sodium, potassium, and alumina in the ash will be overwhelmed by the sodium, potassium, and alumina from the feed but the impact from the other ash components needs to be quantified. A maximum coal particle size is specified so the feed system does not plug and a minimum particle size is specified to prevent excess elutriation from the DMR to the Process Gas Filter (PGF). A vendor specification was used to procure the calcined coal for IWTU processing. While the vendor supplied a composite analysis for the 22 tons of coal (Appendix A), this study compares independent analyses of the coal performed at the Savannah River National Laboratory (SRNL) and at the National Energy Technology Laboratory (NETL). Three supersacks a were sampled at three different heights within the sack in order to determine within bag variability and between bag variability of the coal. These analyses were also compared to the vendor’s composite analyses and to the coal specification. These analyses were also compared to historic data on Bestac coal analyses that had been performed at Hazen Research Inc. (HRI) between 2004-2011.

Analysing spatially extended high-dimensional dynamics by recurrence plots

Energy Technology Data Exchange (ETDEWEB)

Marwan, Norbert, E-mail: marwan@pik-potsdam.de [Potsdam Institute for Climate Impact Research, 14412 Potsdam (Germany); Kurths, Jürgen [Potsdam Institute for Climate Impact Research, 14412 Potsdam (Germany); Humboldt Universität zu Berlin, Institut für Physik (Germany); Nizhny Novgorod State University, Department of Control Theory, Nizhny Novgorod (Russian Federation); Foerster, Saskia [GFZ German Research Centre for Geosciences, Section 1.4 Remote Sensing, Telegrafenberg, 14473 Potsdam (Germany)

2015-05-08

Recurrence plot based measures of complexity are capable tools for characterizing complex dynamics. In this letter we show the potential of selected recurrence plot measures for the investigation of even high-dimensional dynamics. We apply this method on spatially extended chaos, such as derived from the Lorenz96 model and show that the recurrence plot based measures can qualitatively characterize typical dynamical properties such as chaotic or periodic dynamics. Moreover, we demonstrate its power by analysing satellite image time series of vegetation cover with contrasting dynamics as a spatially extended and potentially high-dimensional example from the real world. - Highlights: • We use recurrence plots for analysing partially extended dynamics. • We investigate the high-dimensional chaos of the Lorenz96 model. • The approach distinguishes different spatio-temporal dynamics. • We use the method for studying vegetation cover time series.

RNA-sequencing-based transcriptome and biochemical analyses of steroidal saponin pathway in a complete set of Allium fistulosum—A. cepa monosomic addition lines

Science.gov (United States)

Abdelrahman, Mostafa; El-Sayed, Magdi; Sato, Shusei; Hirakawa, Hideki; Ito, Shin-ichi; Tanaka, Keisuke; Mine, Yoko; Sugiyama, Nobuo; Suzuki, Minoru; Yamauchi, Naoki

2017-01-01

The genus Allium is a rich source of steroidal saponins, and its medicinal properties have been attributed to these bioactive compounds. The saponin compounds with diverse structures play a pivotal role in Allium’s defense mechanism. Despite numerous studies on the occurrence and chemical structure of steroidal saponins, their biosynthetic pathway in Allium species is poorly understood. The monosomic addition lines (MALs) of the Japanese bunching onion (A. fistulosum, FF) with an extra chromosome from the shallot (A. cepa Aggregatum group, AA) are powerful genetic resources that enable us to understand many physiological traits of Allium. In the present study, we were able to isolate and identify Alliospiroside A saponin compound in A. fistulosum with extra chromosome 2A from shallot (FF2A) and its role in the defense mechanism against Fusarium pathogens. Furthermore, to gain molecular insight into the Allium saponin biosynthesis pathway, high-throughput RNA-Seq of the root, bulb, and leaf of AA, MALs, and FF was carried out using Illumina's HiSeq 2500 platform. An open access Allium Transcript Database (Allium TDB, http://alliumtdb.kazusa.or.jp) was generated based on RNA-Seq data. The resulting assembled transcripts were functionally annotated, revealing 50 unigenes involved in saponin biosynthesis. Differential gene expression (DGE) analyses of AA and MALs as compared with FF (as a control) revealed a strong up-regulation of the saponin downstream pathway, including cytochrome P450, glycosyltransferase, and beta-glucosidase in chromosome 2A. An understanding of the saponin compounds and biosynthesis-related genes would facilitate the development of plants with unique saponin content and, subsequently, improved disease resistance. PMID:28800607

RNA-sequencing-based transcriptome and biochemical analyses of steroidal saponin pathway in a complete set of Allium fistulosum-A. cepa monosomic addition lines.

Science.gov (United States)

Abdelrahman, Mostafa; El-Sayed, Magdi; Sato, Shusei; Hirakawa, Hideki; Ito, Shin-Ichi; Tanaka, Keisuke; Mine, Yoko; Sugiyama, Nobuo; Suzuki, Yutaka; Yamauchi, Naoki; Shigyo, Masayoshi

2017-01-01

The genus Allium is a rich source of steroidal saponins, and its medicinal properties have been attributed to these bioactive compounds. The saponin compounds with diverse structures play a pivotal role in Allium's defense mechanism. Despite numerous studies on the occurrence and chemical structure of steroidal saponins, their biosynthetic pathway in Allium species is poorly understood. The monosomic addition lines (MALs) of the Japanese bunching onion (A. fistulosum, FF) with an extra chromosome from the shallot (A. cepa Aggregatum group, AA) are powerful genetic resources that enable us to understand many physiological traits of Allium. In the present study, we were able to isolate and identify Alliospiroside A saponin compound in A. fistulosum with extra chromosome 2A from shallot (FF2A) and its role in the defense mechanism against Fusarium pathogens. Furthermore, to gain molecular insight into the Allium saponin biosynthesis pathway, high-throughput RNA-Seq of the root, bulb, and leaf of AA, MALs, and FF was carried out using Illumina's HiSeq 2500 platform. An open access Allium Transcript Database (Allium TDB, http://alliumtdb.kazusa.or.jp) was generated based on RNA-Seq data. The resulting assembled transcripts were functionally annotated, revealing 50 unigenes involved in saponin biosynthesis. Differential gene expression (DGE) analyses of AA and MALs as compared with FF (as a control) revealed a strong up-regulation of the saponin downstream pathway, including cytochrome P450, glycosyltransferase, and beta-glucosidase in chromosome 2A. An understanding of the saponin compounds and biosynthesis-related genes would facilitate the development of plants with unique saponin content and, subsequently, improved disease resistance.

Kinetic stability analyses in a bumpy cylinder

International Nuclear Information System (INIS)

Dominguez, R.R.; Berk, H.L.

1981-01-01

Recent interest in the ELMO Bumpy Torus (EBT) has prompted a number of stability analyses of both the hot electron rings and the toroidal plasma. Typically these works employ the local approximation, neglecting radial eigenmode structure and ballooning effects to perform the stability analysis. In the present work we develop a fully kinetic formalism for performing nonlocal stability analyses in a bumpy cylinder. We show that the Vlasov-Maxwell integral equations (with one ignorable coordinate) are self-adjoint and hence amenable to analysis using numerical techniques developed for self-adjoint systems of equations. The representation we obtain for the kernel of the Vlasov-Maxwell equations is a differential operator of arbitrarily high order. This form leads to a manifestly self-adjoint system of differential equations for long wavelength modes

ALBEDO PATTERN RECOGNITION AND TIME-SERIES ANALYSES IN MALAYSIA

Directory of Open Access Journals (Sweden)

S. A. Salleh

2012-07-01

Full Text Available Pattern recognition and time-series analyses will enable one to evaluate and generate predictions of specific phenomena. The albedo pattern and time-series analyses are very much useful especially in relation to climate condition monitoring. This study is conducted to seek for Malaysia albedo pattern changes. The pattern recognition and changes will be useful for variety of environmental and climate monitoring researches such as carbon budgeting and aerosol mapping. The 10 years (2000–2009 MODIS satellite images were used for the analyses and interpretation. These images were being processed using ERDAS Imagine remote sensing software, ArcGIS 9.3, the 6S code for atmospherical calibration and several MODIS tools (MRT, HDF2GIS, Albedo tools. There are several methods for time-series analyses were explored, this paper demonstrates trends and seasonal time-series analyses using converted HDF format MODIS MCD43A3 albedo land product. The results revealed significance changes of albedo percentages over the past 10 years and the pattern with regards to Malaysia's nebulosity index (NI and aerosol optical depth (AOD. There is noticeable trend can be identified with regards to its maximum and minimum value of the albedo. The rise and fall of the line graph show a similar trend with regards to its daily observation. The different can be identified in term of the value or percentage of rises and falls of albedo. Thus, it can be concludes that the temporal behavior of land surface albedo in Malaysia have a uniform behaviours and effects with regards to the local monsoons. However, although the average albedo shows linear trend with nebulosity index, the pattern changes of albedo with respects to the nebulosity index indicates that there are external factors that implicates the albedo values, as the sky conditions and its diffusion plotted does not have uniform trend over the years, especially when the trend of 5 years interval is examined, 2000 shows high

FY01 Supplemental Science and Performance Analysis: Volume 1, Scientific Bases and Analyses

International Nuclear Information System (INIS)

Bodvarsson, G.S.; Dobson, David

2001-01-01

The U.S. Department of Energy (DOE) is considering the possible recommendation of a site at Yucca Mountain, Nevada, for development as a geologic repository for the disposal of high-level radioactive waste and spent nuclear fuel. To facilitate public review and comment, in May 2001 the DOE released the Yucca Mountain Science and Engineering Report (S and ER) (DOE 2001 [DIRS 153849]), which presents technical information supporting the consideration of the possible site recommendation. The report summarizes the results of more than 20 years of scientific and engineering studies. A decision to recommend the site has not been made: the DOE has provided the S and ER and its supporting documents as an aid to the public in formulating comments on the possible recommendation. When the S and ER (DOE 2001 [DIRS 153849]) was released, the DOE acknowledged that technical and scientific analyses of the site were ongoing. Therefore, the DOE noted in the Federal Register Notice accompanying the report (66 FR 23013 [DIRS 155009], p. 2) that additional technical information would be released before the dates, locations, and times for public hearings on the possible recommendation were announced. This information includes: (1) the results of additional technical studies of a potential repository at Yucca Mountain, contained in this FY01 Supplemental Science and Performance Analyses: Vol. 1, Scientific Bases and Analyses; and FY01 Supplemental Science and Performance Analyses: Vol. 2, Performance Analyses (McNeish 2001 [DIRS 155023]) (collectively referred to as the SSPA) and (2) a preliminary evaluation of the Yucca Mountain site's preclosure and postclosure performance against the DOE's proposed site suitability guidelines (10 CFR Part 963 [64 FR 67054 [DIRS 124754

FY01 Supplemental Science and Performance Analysis: Volume 1,Scientific Bases and Analyses

Energy Technology Data Exchange (ETDEWEB)

Bodvarsson, G.S.; Dobson, David

2001-05-30

The U.S. Department of Energy (DOE) is considering the possible recommendation of a site at Yucca Mountain, Nevada, for development as a geologic repository for the disposal of high-level radioactive waste and spent nuclear fuel. To facilitate public review and comment, in May 2001 the DOE released the Yucca Mountain Science and Engineering Report (S&ER) (DOE 2001 [DIRS 153849]), which presents technical information supporting the consideration of the possible site recommendation. The report summarizes the results of more than 20 years of scientific and engineering studies. A decision to recommend the site has not been made: the DOE has provided the S&ER and its supporting documents as an aid to the public in formulating comments on the possible recommendation. When the S&ER (DOE 2001 [DIRS 153849]) was released, the DOE acknowledged that technical and scientific analyses of the site were ongoing. Therefore, the DOE noted in the Federal Register Notice accompanying the report (66 FR 23013 [DIRS 155009], p. 2) that additional technical information would be released before the dates, locations, and times for public hearings on the possible recommendation were announced. This information includes: (1) the results of additional technical studies of a potential repository at Yucca Mountain, contained in this FY01 Supplemental Science and Performance Analyses: Vol. 1, Scientific Bases and Analyses; and FY01 Supplemental Science and Performance Analyses: Vol. 2, Performance Analyses (McNeish 2001 [DIRS 155023]) (collectively referred to as the SSPA) and (2) a preliminary evaluation of the Yucca Mountain site's preclosure and postclosure performance against the DOE's proposed site suitability guidelines (10 CFR Part 963 [64 FR 67054 [DIRS 124754

Analyse Risk-Return Paradox: Evidence from Electricity Sector of Pakistan

OpenAIRE

Naqi Shah, Sadia; Qayyum, Abdul

2016-01-01

This study analyse risk return relationship of the electricity companies of Pakistan by using the log return series of these electricity companies. Financial time series data have the property of autoregressive heteroscedasticity so move towards the GARCH family test. As the study want to analyse the risk return relationship so, GARCH-M Model of Engel et al (1987) is used, who empirically found relationship between risk and return. Results show that risk return in case of Pakistan electricity...

Race, Gender, and Reseacher Positionality Analysed Through Memory Work

DEFF Research Database (Denmark)

Andreassen, Rikke; Myong, Lene

2017-01-01

Drawing upon feminist standpoint theory and memory work, the authors analyse racial privilege by investigating their own racialized and gendered subjectifications as academic researchers. By looking at their own experiences within academia, they show how authority and agency are contingent upon...

Comparative biochemical analyses of venous blood and peritoneal fluid from horses with colic using a portable analyser and an in-house analyser.

Science.gov (United States)

Saulez, M N; Cebra, C K; Dailey, M

2005-08-20

Fifty-six horses with colic were examined over a period of three months. The concentrations of glucose, lactate, sodium, potassium and chloride, and the pH of samples of blood and peritoneal fluid, were determined with a portable clinical analyser and with an in-house analyser and the results were compared. Compared with the in-house analyser, the portable analyser gave higher pH values for blood and peritoneal fluid with greater variability in the alkaline range, and lower pH values in the acidic range, lower concentrations of glucose in the range below 8.3 mmol/l, and lower concentrations of lactate in venous blood in the range below 5 mmol/l and in peritoneal fluid in the range below 2 mmol/l, with less variability. On average, the portable analyser underestimated the concentrations of lactate and glucose in peritoneal fluid in comparison with the in-house analyser. Its measurements of the concentrations of sodium and chloride in peritoneal fluid had a higher bias and were more variable than the measurements in venous blood, and its measurements of potassium in venous blood and peritoneal fluid had a smaller bias and less variability than the measurements made with the in-house analyser.

Network-derived inhomogeneity in monthly rainfall analyses over western Tasmania

International Nuclear Information System (INIS)

Fawcett, Robert; Trewin, Blair; Barnes-Keoghan, Ian

2010-01-01

Monthly rainfall in the wetter western half of Tasmania was relatively poorly observed in the early to middle parts of the 20th century, and this causes a marked inhomogeneity in the operational gridded monthly rainfall analyses generated by the Australian Bureau of Meteorology up until the end of 2009. These monthly rainfall analyses were generated for the period 1900 to 2009 in two forms; a national analysis at 0.25 0 latitude-longitude resolution, and a southeastern Australia regional analysis at 0.1 0 resolution. For any given month, they used all the monthly data from the standard Bureau rainfall gauge network available in the Australian Data Archive for Meteorology. Since this network has changed markedly since Federation (1901), there is obvious scope for network-derived inhomogeneities in the analyses. In this study, we show that the topography-resolving techniques of the new Australian Water Availability Project analyses, adopted as the official operational analyses from the start of 2010, substantially diminish those inhomogeneities, while using largely the same observation network. One result is an improved characterisation of recent rainfall declines across Tasmania. The new analyses are available at two resolutions, 0.25 0 and 0.05 0 .

LOD score exclusion analyses for candidate genes using random population samples.

Science.gov (United States)

Deng, H W; Li, J; Recker, R R

2001-05-01

While extensive analyses have been conducted to test for, no formal analyses have been conducted to test against, the importance of candidate genes with random population samples. We develop a LOD score approach for exclusion analyses of candidate genes with random population samples. Under this approach, specific genetic effects and inheritance models at candidate genes can be analysed and if a LOD score is < or = - 2.0, the locus can be excluded from having an effect larger than that specified. Computer simulations show that, with sample sizes often employed in association studies, this approach has high power to exclude a gene from having moderate genetic effects. In contrast to regular association analyses, population admixture will not affect the robustness of our analyses; in fact, it renders our analyses more conservative and thus any significant exclusion result is robust. Our exclusion analysis complements association analysis for candidate genes in random population samples and is parallel to the exclusion mapping analyses that may be conducted in linkage analyses with pedigrees or relative pairs. The usefulness of the approach is demonstrated by an application to test the importance of vitamin D receptor and estrogen receptor genes underlying the differential risk to osteoporotic fractures.

Diagnostic Comparison of Meteorological Analyses during the 2002 Antarctic Winter

Science.gov (United States)

Manney, Gloria L.; Allen, Douglas R.; Kruger, Kirstin; Naujokat, Barbara; Santee, Michelle L.; Sabutis, Joseph L.; Pawson, Steven; Swinbank, Richard; Randall, Cora E.; Simmons, Adrian J.;

Fatigue crack growth in additive manufactured products

Directory of Open Access Journals (Sweden)

A. Riemer

2015-10-01

Full Text Available Additive Manufacturing (AM is a new innovative technique that allows the direct fabrication of complex, individual, delicate and high-strength products, based on their 3D data. Selective Laser Melting (SLM is one of the AM processes that generates metallic components layer by layer using powder-bed technique. The irradiation and consequent melting of metallic powder is realised by the laser source. Employing SLM, especially complex and individual products, such as implants or aerospace parts, are well suited for economic production in small batches. The first important issue in this work was to analyse the fatigue crack growth (FCG in titanium alloy Ti-6-4 and stainless steel 316L processed by SLM. As a first step, stress intensity range decreasing tests were performed on SLM samples in their “as-built” condition. The next step was to adopt measures for optimisation of fatigue crack growth performance of SLM parts. For this purpose various heat treatments such as stress relief annealing and hot isostatic pressing (HIP were applied to the CT specimens. Finally, the strong impact of heat treatment on the residual lifetime was demonstrated by numerical fatigue crack growth simulations. For this purpose, the hip joint implant consisting of Ti-6-4 and processed by SLM was taken into account. It was found that residual stresses have a strong influence on the crack growth in Ti-6-4, while the influence of the micro-pores on the threshold values remains low. In contrast the results for 316L show that its fracturemechanical behaviour is not affected by residual stresses, whereas the microstructural features lead to modification in the da/dN-K-data. The second fundamental aim of this work was to demonstrate the possibilities of the SLM process. For that reason, the individually tailored bicycle crank was optimised regarding its weight and local stresses and finally manufactured using the SLM system. The iterative optimisation procedure was based on

Basophil activation test with food additives in chronic urticaria patients.

Science.gov (United States)

Kang, Min-Gyu; Song, Woo-Jung; Park, Han-Ki; Lim, Kyung-Hwan; Kim, Su-Jung; Lee, Suh-Young; Kim, Sae-Hoon; Cho, Sang-Heon; Min, Kyung-Up; Chang, Yoon-Seok

2014-01-01

The role of food additives in chronic urticaria (CU) is still under investigation. In this study, we aimed to explore the association between food additives and CU by using the basophil activation test (BAT). The BAT using 15 common food additives was performed for 15 patients with CU who had a history of recurrent urticarial aggravation following intake of various foods without a definite food-specific IgE. Of the 15 patients studied, two (13.3%) showed positive BAT results for one of the tested food additives. One patient responded to monosodium glutamate, showing 18.7% of CD203c-positive basophils. Another patient showed a positive BAT result to sodium benzoate. Both patients had clinical correlations with the agents, which were partly determined by elimination diets. The present study suggested that at least a small proportion of patients with CU had symptoms associated with food additives. The results may suggest the potential utility of the BAT to identity the role of food additives in CU.

Short communication: Effect of whey protein addition and transglutaminase treatment on the physical and sensory properties of reduced-fat ice cream.

Science.gov (United States)

Danesh, Erfan; Goudarzi, Mostafa; Jooyandeh, Hossein

2017-07-01

The effects of whey protein addition and transglutaminase treatment, alone and in combination, on the physical and sensory properties of reduced-fat ice cream were investigated. Adding whey protein with or without enzyme treatment decreased melting rate, overrun, and hardness of the reduced-fat ice cream; however, the enzyme-treated sample had a higher melting rate and overrun and softer texture. Whey protein-fortified samples showed higher melting resistance, but lower overrun and firmer texture compared with the enzyme-treated sample without added whey protein. Whey protein addition with or without transglutaminase treatment caused an increase in apparent viscosity and a decrease in flow index of the reduced-fat ice cream; nevertheless, the flow behavior of full-fat sample was most similar to the enzyme-treated reduced-fat sample with no added whey protein. Descriptive sensory analyses showed that neither whey protein addition nor transglutaminase treatment significantly influenced the flavor and odor of reduced-fat ice cream, but they both noticeably improved the color and texture of the final product. The results of this study suggest that whey protein addition with transglutaminase treatment improves the physical and sensory properties of reduced-fat ice cream more favorably than does whey protein addition or transglutaminase treatment alone. Copyright © 2017 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Plant dynamics analyses of fast reactor concept: RAPID-A without any control rod

International Nuclear Information System (INIS)

Kambe, Mitsuru

1996-01-01

Plant dynamics analyses of a fast reactor concept RAPID-A without any control rod have been demonstrated in case of reactor startup and sudden change of the primary flow rate. RAIP-A concept involves Lithium Expansion Module (LEM) for inherent reactivity feedback, Lithium Injection Module (LIM) for inherent ultimate shutdown and Lithium Release Module (LRM) for automated reactor startup. LEM consists of Quick-LEM and Slow-LEM. Slow-LEM provides with moderate reactivity addition as decreasing temperature. Quick-LEM assures quick negative reactivity feedback as increasing temperature. Plant dynamics analyses revealed that reactor power is nearly proportional to the primary flow rate even if the flow rate increases suddenly. Fully automated reactor startup from the subcritical condition has been attempted by inserting reactivity at a constant rate by LRM. Allowable rate of reactivity addition has been obtained in respect to Quick-LEM reactivity worth. (author)

Strengthen forensic entomology in court--the need for data exploration and the validation of a generalised additive mixed model.

Science.gov (United States)

Baqué, Michèle; Amendt, Jens

2013-01-01

Developmental data of juvenile blow flies (Diptera: Calliphoridae) are typically used to calculate the age of immature stages found on or around a corpse and thus to estimate a minimum post-mortem interval (PMI(min)). However, many of those data sets don't take into account that immature blow flies grow in a non-linear fashion. Linear models do not supply a sufficient reliability on age estimates and may even lead to an erroneous determination of the PMI(min). According to the Daubert standard and the need for improvements in forensic science, new statistic tools like smoothing methods and mixed models allow the modelling of non-linear relationships and expand the field of statistical analyses. The present study introduces into the background and application of these statistical techniques by analysing a model which describes the development of the forensically important blow fly Calliphora vicina at different temperatures. The comparison of three statistical methods (linear regression, generalised additive modelling and generalised additive mixed modelling) clearly demonstrates that only the latter provided regression parameters that reflect the data adequately. We focus explicitly on both the exploration of the data--to assure their quality and to show the importance of checking it carefully prior to conducting the statistical tests--and the validation of the resulting models. Hence, we present a common method for evaluating and testing forensic entomological data sets by using for the first time generalised additive mixed models.

Elemental abundance and analyses with coadded DAO spectrograms

International Nuclear Information System (INIS)

Adelman, S.J.

1987-01-01

One can improve the quality of elemental abundance analyses by using higher signal-to-noise data than has been the practice at high resolution. The procedures developed at the Dominion Astrophysical Observatory to coadd high-dispersion coude spectrograms are used with a minimum of 10 6.5 A mm -1 IIa-O spectrograms of each of three field horizontal-branch (FHB)A stars to increase the signal-to-noise ratio of the photographic data over a considerable wavelength region. Fine analyses of the sharp-lined prototype FHB stars HD 109995 and 161817 show an internal consistency which justifies this effort. Their photospheric elemental abundances are similar to those of Population II globular cluster giants. (author)

Unconscious analyses of visual scenes based on feature conjunctions.

Science.gov (United States)

Tachibana, Ryosuke; Noguchi, Yasuki

2015-06-01

To efficiently process a cluttered scene, the visual system analyzes statistical properties or regularities of visual elements embedded in the scene. It is controversial, however, whether those scene analyses could also work for stimuli unconsciously perceived. Here we show that our brain performs the unconscious scene analyses not only using a single featural cue (e.g., orientation) but also based on conjunctions of multiple visual features (e.g., combinations of color and orientation information). Subjects foveally viewed a stimulus array (duration: 50 ms) where 4 types of bars (red-horizontal, red-vertical, green-horizontal, and green-vertical) were intermixed. Although a conscious perception of those bars was inhibited by a subsequent mask stimulus, the brain correctly analyzed the information about color, orientation, and color-orientation conjunctions of those invisible bars. The information of those features was then used for the unconscious configuration analysis (statistical processing) of the central bars, which induced a perceptual bias and illusory feature binding in visible stimuli at peripheral locations. While statistical analyses and feature binding are normally 2 key functions of the visual system to construct coherent percepts of visual scenes, our results show that a high-level analysis combining those 2 functions is correctly performed by unconscious computations in the brain. (c) 2015 APA, all rights reserved).

Economic value addition, employment, and enterprise profiles of local authorities in the Free State, South Africa

Directory of Open Access Journals (Sweden)

Danie Francois Toerien

2015-12-01

Full Text Available A strong underlying structure in the economic, demographic, and entrepreneurial domains of local authorities (municipalities in the Free State, South Africa was detected through cluster and other analyses. The structure is indicative of a system in which economic value addition, population size, employment creation, and entrepreneurial domains are dynamically linked. The agriculture, mining, and fuel and chemicals sectors dominate the economic value addition in some municipalities, whereas others are without a single dominating economic sector (i.e. they have well-balanced economies. The agriculture and households sectors are significant sources of employment in all municipalities. Cluster sequence analyses of the municipalities revealed statistically significant recurring patterns of value addition, employment, and entrepreneurship, further strengthening the detection of orderliness, which can promote mutual learning. The Metsimaholo municipality with a significant manufacturing base is an atypical Free State municipality and provides an outstanding example of the economic, demographic, and entrepreneurial impacts of value addition to local or external primary products.

Multigene analyses resolve early diverging lineages in the Rhodymeniophycidae (Florideophyceae, Rhodophyta).

Science.gov (United States)

Saunders, Gary W; Filloramo, Gina; Dixon, Kyatt; Le Gall, Line; Maggs, Christine A; Kraft, Gerald T

2016-08-01

Multigene phylogenetic analyses were directed at resolving the earliest divergences in the red algal subclass Rhodymeniophycidae. The inclusion of key taxa (new to science and/or previously lacking molecular data), additional sequence data (SSU, LSU, EF2, rbcL, COI-5P), and phylogenetic analyses removing the most variable sites (site stripping) have provided resolution for the first time at these deep nodes. The earliest diverging lineage within the subclass was the enigmatic Catenellopsis oligarthra from New Zealand (Catenellopsidaceae), which is here placed in the Catenellopsidales ord. nov. In our analyses, Atractophora hypnoides was not allied with the other included Bonnemaisoniales, but resolved as sister to the Peyssonneliales, and is here assigned to Atractophoraceae fam. nov. in the Atractophorales ord. nov. Inclusion of Acrothesaurum gemellifilum gen. et sp. nov. from Tasmania has greatly improved our understanding of the Acrosymphytales, to which we assign three families, the Acrosymphytaceae, Acrothesauraceae fam. nov. and Schimmelmanniaceae fam. nov. © 2016 Phycological Society of America.

Utilization of Large Scale Surface Models for Detailed Visibility Analyses

Science.gov (United States)

Caha, J.; Kačmařík, M.

2017-11-01

This article demonstrates utilization of large scale surface models with small spatial resolution and high accuracy, acquired from Unmanned Aerial Vehicle scanning, for visibility analyses. The importance of large scale data for visibility analyses on the local scale, where the detail of the surface model is the most defining factor, is described. The focus is not only the classic Boolean visibility, that is usually determined within GIS, but also on so called extended viewsheds that aims to provide more information about visibility. The case study with examples of visibility analyses was performed on river Opava, near the Ostrava city (Czech Republic). The multiple Boolean viewshed analysis and global horizon viewshed were calculated to determine most prominent features and visibility barriers of the surface. Besides that, the extended viewshed showing angle difference above the local horizon, which describes angular height of the target area above the barrier, is shown. The case study proved that large scale models are appropriate data source for visibility analyses on local level. The discussion summarizes possible future applications and further development directions of visibility analyses.

Comprehensive research synopsis and systematic meta-analyses in Parkinson's disease genetics: The PDGene database.

Directory of Open Access Journals (Sweden)

Christina M Lill

Full Text Available More than 800 published genetic association studies have implicated dozens of potential risk loci in Parkinson's disease (PD. To facilitate the interpretation of these findings, we have created a dedicated online resource, PDGene, that comprehensively collects and meta-analyzes all published studies in the field. A systematic literature screen of -27,000 articles yielded 828 eligible articles from which relevant data were extracted. In addition, individual-level data from three publicly available genome-wide association studies (GWAS were obtained and subjected to genotype imputation and analysis. Overall, we performed meta-analyses on more than seven million polymorphisms originating either from GWAS datasets and/or from smaller scale PD association studies. Meta-analyses on 147 SNPs were supplemented by unpublished GWAS data from up to 16,452 PD cases and 48,810 controls. Eleven loci showed genome-wide significant (P < 5 × 10(-8 association with disease risk: BST1, CCDC62/HIP1R, DGKQ/GAK, GBA, LRRK2, MAPT, MCCC1/LAMP3, PARK16, SNCA, STK39, and SYT11/RAB25. In addition, we identified novel evidence for genome-wide significant association with a polymorphism in ITGA8 (rs7077361, OR 0.88, P  =  1.3 × 10(-8. All meta-analysis results are freely available on a dedicated online database (www.pdgene.org, which is cross-linked with a customized track on the UCSC Genome Browser. Our study provides an exhaustive and up-to-date summary of the status of PD genetics research that can be readily scaled to include the results of future large-scale genetics projects, including next-generation sequencing studies.

Deposition of additives onto surface of carbon materials by blending method--general conception

International Nuclear Information System (INIS)

Przepiorski, Jacek

2005-01-01

Carbon fibers loaded with potassium carbonate and with metallic copper were prepared by applying a blending method. Raw isotropic coal pitch was blended with KOH or CuBr 2 and obtained mixtures were subjected to spinning. In this way KOH and copper salt-blended fiber with uniform distribution of potassium and copper were spun. The raw fibers were exposed to stabilization with a mixture of CO 2 and air or air only through heating to 330 deg. C and next to treatment with carbon dioxide or hydrogen at higher temperatures. Electron probe micro-analysis (EPMA) analyses showed presence of potassium carbonate or metallic copper predominantly in peripheral regions of the obtained fibers. Basing on the mechanisms of potassium and copper diffusion over the carbon volume, generalized method for the deposition of additives onto surface of carbon materials is proposed

Ten cases of severe oral lichen planus showing granular C3 deposition in oral mucosal basement membrane zone.

Science.gov (United States)

Hashimoto, Takashi; Fukuda, Aoi; Himejima, Akio; Morita, Shosuke; Tsuruta, Daisuke; Koga, Hiroshi; Krol, Rafal P; Ishii, Norito

2015-01-01

Oral lichen planus (OLP) may show depositions of immunoglobulins and complement components in oral mucosal basement membrane zone (BMZ) in direct immunofluorescence, although these finding are not frequently seen. We collected and examined ten cases of severe OLP showing granular C3 deposition in BMZ. In addition to clinical, histopathological and direct immunofluorescence assessments, we performed various immune-serological tests, including indirect immunofluorescence of normal human skin and 1M NaCl-split skin, immunoblotting of normal human epidermal and dermal extracts, recombinant proteins of BP180 NC16a and C-terminal domains, concentrated culture supernatant of HaCaT cells and purified human laminin-332, and enzyme-linked immunosorbent assays for BP230 and BP180. Direct immunofluorescence showed C3 deposition in BMZ exclusively of granular pattern in 7 cases and of both granular and linear patterns in 3 cases. The 10 cases showed no positive reactivity for either IgG or IgA antibodies in any immuno-serological tests. Detailed analyses of clinical, histopathological and immunological findings revealed striking female prevalence, although other parameters were in general characteristic of OLP. Granular C3 deposition in oral BMZ may be one of the characteristic features of severe OLP, although mechanisms for C3 deposition and its pathogenic role in OLP are currently unknown.

Target gene analyses of 39 amelogenesis imperfecta kindreds

Science.gov (United States)

Chan, Hui-Chen; Estrella, Ninna M. R. P.; Milkovich, Rachel N.; Kim, Jung-Wook; Simmer, James P.; Hu, Jan C-C.

2012-01-01

Previously, mutational analyses identified six disease-causing mutations in 24 amelogenesis imperfecta (AI) kindreds. We have since expanded the number of AI kindreds to 39, and performed mutation analyses covering the coding exons and adjoining intron sequences for the six proven AI candidate genes [amelogenin (AMELX), enamelin (ENAM), family with sequence similarity 83, member H (FAM83H), WD repeat containing domain 72 (WDR72), enamelysin (MMP20), and kallikrein-related peptidase 4 (KLK4)] and for ameloblastin (AMBN) (a suspected candidate gene). All four of the X-linked AI families (100%) had disease-causing mutations in AMELX, suggesting that AMELX is the only gene involved in the aetiology of X-linked AI. Eighteen families showed an autosomal-dominant pattern of inheritance. Disease-causing mutations were identified in 12 (67%): eight in FAM83H, and four in ENAM. No FAM83H coding-region or splice-junction mutations were identified in three probands with autosomal-dominant hypocalcification AI (ADHCAI), suggesting that a second gene may contribute to the aetiology of ADHCAI. Six families showed an autosomal-recessive pattern of inheritance, and disease-causing mutations were identified in three (50%): two in MMP20, and one in WDR72. No disease-causing mutations were found in 11 families with only one affected member. We conclude that mutation analyses of the current candidate genes for AI have about a 50% chance of identifying the disease-causing mutation in a given kindred. PMID:22243262

Show-Bix &

DEFF Research Database (Denmark)

2014-01-01

The anti-reenactment 'Show-Bix &' consists of 5 dias projectors, a dial phone, quintophonic sound, and interactive elements. A responsive interface will enable the Dias projectors to show copies of original dias slides from the Show-Bix piece ”March på Stedet”, 265 images in total. The copies are...

Measuring the apparent diffusion coefficient in primary rectal tumors: is there a benefit in performing histogram analyses?

Science.gov (United States)

van Heeswijk, Miriam M; Lambregts, Doenja M J; Maas, Monique; Lahaye, Max J; Ayas, Z; Slenter, Jos M G M; Beets, Geerard L; Bakers, Frans C H; Beets-Tan, Regina G H

2017-06-01

The apparent diffusion coefficient (ADC) is a potential prognostic imaging marker in rectal cancer. Typically, mean ADC values are used, derived from precise manual whole-volume tumor delineations by experts. The aim was first to explore whether non-precise circular delineation combined with histogram analysis can be a less cumbersome alternative to acquire similar ADC measurements and second to explore whether histogram analyses provide additional prognostic information. Thirty-seven patients who underwent a primary staging MRI including diffusion-weighted imaging (DWI; b0, 25, 50, 100, 500, 1000; 1.5 T) were included. Volumes-of-interest (VOIs) were drawn on b1000-DWI: (a) precise delineation, manually tracing tumor boundaries (2 expert readers), and (b) non-precise delineation, drawing circular VOIs with a wide margin around the tumor (2 non-experts). Mean ADC and histogram metrics (mean, min, max, median, SD, skewness, kurtosis, 5th-95th percentiles) were derived from the VOIs and delineation time was recorded. Measurements were compared between the two methods and correlated with prognostic outcome parameters. Median delineation time reduced from 47-165 s (precise) to 21-43 s (non-precise). The 45th percentile of the non-precise delineation showed the best correlation with the mean ADC from the precise delineation as the reference standard (ICC 0.71-0.75). None of the mean ADC or histogram parameters showed significant prognostic value; only the total tumor volume (VOI) was significantly larger in patients with positive clinical N stage and mesorectal fascia involvement. When performing non-precise tumor delineation, histogram analysis (in specific 45th ADC percentile) may be used as an alternative to obtain similar ADC values as with precise whole tumor delineation. Histogram analyses are not beneficial to obtain additional prognostic information.

The additive hazards model with high-dimensional regressors

DEFF Research Database (Denmark)

Martinussen, Torben; Scheike, Thomas

2009-01-01

This paper considers estimation and prediction in the Aalen additive hazards model in the case where the covariate vector is high-dimensional such as gene expression measurements. Some form of dimension reduction of the covariate space is needed to obtain useful statistical analyses. We study...... model. A standard PLS algorithm can also be constructed, but it turns out that the resulting predictor can only be related to the original covariates via time-dependent coefficients. The methods are applied to a breast cancer data set with gene expression recordings and to the well known primary biliary...

Steady-state and accident analyses of PBMR with the computer code SPECTRA

International Nuclear Information System (INIS)

Stempniewicz, Marek M.

2002-01-01

The SPECTRA code is an accident analysis code developed at NRG. It is designed for thermal-hydraulic analyses of nuclear or conventional power plants. The code is capable of analysing the whole power plant, including reactor vessel, primary system, various control and safety systems, containment and reactor building. The aim of the work presented in this paper was to prepare a preliminary thermal-hydraulic model of PBMR for SPECTRA, and perform steady state and accident analyses. In order to assess SPECTRA capability to model the PBMR reactors, a model of the INCOGEN system has been prepared first. Steady state and accident scenarios were analyzed for INCOGEN configuration. Results were compared to the results obtained earlier with INAS and OCTOPUS/PANTHERMIX. A good agreement was obtained. Results of accident analyses with PBMR model showed qualitatively good results. It is concluded that SPECTRA is a suitable tool for analyzing High Temperature Reactors, such as INCOGEN or for example PBMR (Pebble Bed Modular Reactor). Analyses of INCOGEN and PBMR systems showed that in all analyzed cases the fuel temperatures remained within the acceptable limits. Consequently there is no danger of release of radioactivity to the environment. It may be concluded that those are promising designs for future safe industrial reactors. (author)

Early hydration of portland cement with crystalline mineral additions

International Nuclear Information System (INIS)

Rahhal, V.; Talero, R.

2005-01-01

This research presents the effects of finely divided crystalline mineral additions (quartz and limestone), commonly known as filler, on the early hydration of portland cements with very different mineralogical composition. The used techniques to study the early hydration of blended cements were conduction calorimeter, hydraulicity (Fratini's test), non-evaporable water and X-ray diffraction. Results showed that the stimulation and the dilution effects increase when the percentage of crystalline mineral additions used is increased. Depending on the replacement proportion, the mineralogical cement composition and the type of crystalline addition, at 2 days, the prevalence of the dilution effect or the stimulation effect shows that crystalline mineral additions could act as sites of heat dissipation or heat stimulation, respectively

Reduction and technical simplification of testing protocol for walking based on repeatability analyses: An Interreg IVa pilot study

Directory of Open Access Journals (Sweden)

Nejc Sarabon

2010-12-01

Full Text Available The aim of this study was to define the most appropriate gait measurement protocols to be used in our future studies in the Mobility in Ageing project. A group of young healthy volunteers took part in the study. Each subject carried out a 10-metre walking test at five different speeds (preferred, very slow, very fast, slow, and fast. Each walking speed was repeated three times, making a total of 15 trials which were carried out in a random order. Each trial was simultaneously analysed by three observers using three different technical approaches: a stop watch, photo cells and electronic kinematic dress. In analysing the repeatability of the trials, the results showed that of the five self-selected walking speeds, three of them (preferred, very fast, and very slow had a significantly higher repeatability of the average walking velocity, step length and cadence than the other two speeds. Additionally, the data showed that one of the three technical methods for gait assessment has better metric characteristics than the other two. In conclusion, based on repeatability, technical and organizational simplification, this study helped us to successfully define a simple and reliable walking test to be used in the main study of the project.

Transformation (normalization) of slope gradient and surface curvatures, automated for statistical analyses from DEMs

Science.gov (United States)

Csillik, O.; Evans, I. S.; Drăguţ, L.

2015-03-01

Automated procedures are developed to alleviate long tails in frequency distributions of morphometric variables. They minimize the skewness of slope gradient frequency distributions, and modify the kurtosis of profile and plan curvature distributions toward that of the Gaussian (normal) model. Box-Cox (for slope) and arctangent (for curvature) transformations are tested on nine digital elevation models (DEMs) of varying origin and resolution, and different landscapes, and shown to be effective. Resulting histograms are illustrated and show considerable improvements over those for previously recommended slope transformations (sine, square root of sine, and logarithm of tangent). Unlike previous approaches, the proposed method evaluates the frequency distribution of slope gradient values in a given area and applies the most appropriate transform if required. Sensitivity of the arctangent transformation is tested, showing that Gaussian-kurtosis transformations are acceptable also in terms of histogram shape. Cube root transformations of curvatures produced bimodal histograms. The transforms are applicable to morphometric variables and many others with skewed or long-tailed distributions. By avoiding long tails and outliers, they permit parametric statistics such as correlation, regression and principal component analyses to be applied, with greater confidence that requirements for linearity, additivity and even scatter of residuals (constancy of error variance) are likely to be met. It is suggested that such transformations should be routinely applied in all parametric analyses of long-tailed variables. Our Box-Cox and curvature automated transformations are based on a Python script, implemented as an easy-to-use script tool in ArcGIS.

The Impact of Including Below Detection Limit Samples in Post Decommissioning Soil Sample Analyses

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Hwan; Yim, Man-Sung [KAIST, Daejeon (Korea, Republic of)

2016-10-15

To meet the required standards the site owner has to show that the soil at the facility has been sufficiently cleaned up. To do this one must know the contamination of the soil at the site prior to clean up. This involves sampling that soil to identify the degree of contamination. However there is a technical difficulty in determining how much decontamination should be done. The problem arises when measured samples are below the detection limit. Regulatory guidelines for site reuse after decommissioning are commonly challenged because the majority of the activity in the soil at or below the limit of detection. Using additional statistical analyses of contaminated soil after decommissioning is expected to have the following advantages: a better and more reliable probabilistic exposure assessment, better economics (lower project costs) and improved communication with the public. This research will develop an approach that defines an acceptable method for demonstrating compliance of decommissioned NPP sites and validates that compliance. Soil samples from NPP often contain censored data. Conventional methods for dealing with censored data sets are statistically biased and limited in their usefulness. In this research, additional methods are performed using real data from a monazite manufacturing factory.

High-Efficient Circuits for Ternary Addition

Directory of Open Access Journals (Sweden)

Reza Faghih Mirzaee

2014-01-01

Full Text Available New ternary adders, which are fundamental components of ternary addition, are presented in this paper. They are on the basis of a logic style which mostly generates binary signals. Therefore, static power dissipation reaches its minimum extent. Extensive different analyses are carried out to examine how efficient the new designs are. For instance, the ternary ripple adder constructed by the proposed ternary half and full adders consumes 2.33 μW less power than the one implemented by the previous adder cells. It is almost twice faster as well. Due to their unique superior characteristics for ternary circuitry, carbon nanotube field-effect transistors are used to form the novel circuits, which are entirely suitable for practical applications.

Regulatory support activities of JNES by thermal-hydraulic and safety analyses

International Nuclear Information System (INIS)

Kasahara, Fumio

2008-01-01

Current status and some related topics on regulatory support activities of Japan Nuclear Energy Safety Organization (JNES) by thermal-hydraulic and safety analyses are reported. The safety of nuclear facilities is secured primarily by plant owners and operators. However, the regulatory body NISA (Nuclear and Industrial Safety Agency) has conducted a strict regulation to confirm the adequacy of the site condition as well as the basic and detailed design. The JNES has been conducting independent analyses from applicants (audit analyses, etc.) by direction of NISA and supporting its review. In addition to the audit analysis, thermal-hydraulic and safety analyses are used in such areas as analytical evaluation for investigation of causes of accidents and troubles, level 2 PSA for risk informed regulation, etc. Recent activities of audit analyses are for the application of Tsuruga 3 and 4 (APWR), the spent fuel storage facility for the establishment, and the LMFBR Monju for the core change. For the trouble event evaluation, the criticality accident analysis of Sika1 was carried out and the evaluation of effectiveness of accident management (AM) measure for Tomari 3 (PWR) and Monju was performed. The analytical codes for these evaluations are continuously revised by reflecting the state-of-art technical information and validated using the information provided by the data from JAEA, OECD project, etc. (author)

K-capture by Al-Si based Additives in an Entrained Flow Reactor

DEFF Research Database (Denmark)

Wang, Guoliang; Jensen, Peter Arendt; Wu, Hao

2016-01-01

A water slurry, consisting of KCl and Al-Si based additives (kaolin and coal fly ash) was fed into an entrained flow reactor (EFR) to study the K-capturing reaction of the additives at suspension-fired conditions. Solid products collected from the reactor were analysed with respect to total...... of KCl to K-aluminosilicate decreased. When reaction temperature increased from 1100 °C to 1450 °C, the conversion of KCl does not change significantly, which differs from the trend observed in fixed-bed reactor....

Conventional and advanced exergetic analyses applied to a combined cycle power plant

International Nuclear Information System (INIS)

Petrakopoulou, Fontina; Tsatsaronis, George; Morosuk, Tatiana; Carassai, Anna

2012-01-01

Conventional exergy-based methods pinpoint components and processes with high irreversibilities. However, they lack certain insight. For a given advanced technological state, there is a minimum level of exergy destruction related to technological and/or economic constraints that is unavoidable. Furthermore, in any thermodynamic system, exergy destruction stems from both component interactions (exogenous) and component inefficiencies (endogenous). To overcome the limitations of the conventional analyses and to increase our knowledge about a plant, advanced exergy-based analyses have been developed. In this paper, a combined cycle power plant is analyzed using both conventional and advanced exergetic analyses. Except for the expander of the gas turbine system and the high-pressure steam turbine, most of the exergy destruction in the plant components is unavoidable. This unavoidable part is constrained by internal technological limitations, i.e. each component’s endogenous exergy destruction. High levels of endogenous exergy destruction show that component interactions do not contribute significantly to the thermodynamic inefficiencies. In addition, these inefficiencies are unavoidable to a large extent. With the advanced analysis, new improvement strategies are revealed that could not otherwise be found. -- Highlights: ► This is the first application of a complete advanced exergetic analysis to a complex power plant. ► In the three-pressure-level combined cycle power plant studied here, the improvement potential of the majority of the components is low, since most of the exergy destruction is unavoidable. ► Component interactions are generally of lower importance for the considered plant. ► Splitting the exogenous exergy destruction reveals one-to-one component interactions and improvement strategies. ► The advanced exergetic analysis is a necessary supplement to the conventional analysis in improving a complex system.

Children with dyslexia show cortical hyperactivation in response to increasing literacy processing demands

Directory of Open Access Journals (Sweden)

Frøydis eMorken

2014-12-01

Full Text Available This fMRI study aimed to examine how differences in literacy processing demands may affect cortical activation patterns in 11- to 12-year-old children with dyslexia as compared to children with typical reading skills. 11 children with and 18 without dyslexia were assessed using a reading paradigm based on different stages of literacy development. In the analyses, six regions showed an interaction effect between group and condition in a factorial ANOVA. These regions were selected as regions of interest for further analyses. Overall, the dyslexia group showed cortical hyperactivation compared to the typical group. The difference between the groups tended to increase with increasing processing demands. Differences in cortical activation were not reflected in in-scanner reading performance. The six regions further grouped into three patterns, which are discussed in terms of processing demands, compensatory mechanisms, orthography and contextual facilitation. We conclude that the observed hyperactivation is chiefly a result of compensatory activity, modulated by other factors.

Additive manufacturing in maxillofacial reconstruction

Directory of Open Access Journals (Sweden)

Dincă Luciana Laura

2017-01-01

Full Text Available In this paper the benefits of using additive manufacturing technologies in maxillofacial reconstruction are highlighted. Based on a real clinical case, the paper describes the manufacture of an implant prototype replacing the right zygomatic bone and a part of maxilla using additive manufacturing technologies. The face is the most expressive part of the human body that makes us unique. It was shown that the maxillofacial prostheses help to improve the psychological state of patients affected by, because low self esteem feeling appears commonly to this patients with the facial defects. The aim of this paper is to show how using additive manufacturing technologies methods within this research, the producing a surgical model will help surgeon to improve the pre-operative planning. For this we used additive manufacturing technologies such as Stereolitography to achieve the biomodel and FDM-fused deposition modelling to obtain a prototype model because these technologies make it possible to obtain prosthesis according to the physical and mechanical requirements of the region of implantation.

Integrative analyses of leprosy susceptibility genes indicate a common autoimmune profile.

Science.gov (United States)

Zhang, Deng-Feng; Wang, Dong; Li, Yu-Ye; Yao, Yong-Gang

2016-04-01

Leprosy is an ancient chronic infection in the skin and peripheral nerves caused by Mycobacterium leprae. The development of leprosy depends on genetic background and the immune status of the host. However, there is no systematic view focusing on the biological pathways, interaction networks and overall expression pattern of leprosy-related immune and genetic factors. To identify the hub genes in the center of leprosy genetic network and to provide an insight into immune and genetic factors contributing to leprosy. We retrieved all reported leprosy-related genes and performed integrative analyses covering gene expression profiling, pathway analysis, protein-protein interaction network, and evolutionary analyses. A list of 123 differentially expressed leprosy related genes, which were enriched in activation and regulation of immune response, was obtained in our analyses. Cross-disorder analysis showed that the list of leprosy susceptibility genes was largely shared by typical autoimmune diseases such as lupus erythematosus and arthritis, suggesting that similar pathways might be affected in leprosy and autoimmune diseases. Protein-protein interaction (PPI) and positive selection analyses revealed a co-evolution network of leprosy risk genes. Our analyses showed that leprosy associated genes constituted a co-evolution network and might undergo positive selection driven by M. leprae. We suggested that leprosy may be a kind of autoimmune disease and the development of leprosy is a matter of defect or over-activation of body immunity. Copyright © 2016 Elsevier Ireland Ltd. All rights reserved.

Studies of CTNNBL1 and FDFT1 variants and measures of obesity: analyses of quantitative traits and case-control studies in 18,014 Danes

DEFF Research Database (Denmark)

Andreasen, Camilla Helene; Mogensen, Mette Sloth; Borch-Johnsen, Knut

2009-01-01

of obesity-related quantitative traits, and case-control studies in large study samples of Danes. METHODS: The FDFT1 rs7001819, CTNNBL1 rs6013029 and rs6020846 were genotyped, using TaqMan allelic discrimination, in a combined study sample comprising 18,014 participants ascertained from; the population...... and a previous study. FDFT1 rs7001819 showed no association with obesity, neither when analysing quantitative traits nor when performing case-control studies of obesity.......). The most significantly associating variants within CTNNBL1 including rs6013029 and rs6020846 were additionally confirmed to associate with morbid obesity in a French Caucasian case-control sample. The aim of this study was to investigate the impact of these three variants on obesity, through analyses...

The effect of alum addition on microbial communities in poultry litter.

Science.gov (United States)

Rothrock, M J; Cook, K L; Warren, J G; Sistani, K

2008-08-01

Alum [Al(2)(SO(4))(3).14H(2)O] is a common poultry litter amendment used to decrease water-soluble phosphorus or reduce ammonia volatilization, or both. Although the physiochemical effects of alum addition have been well researched, little attention has been given to the poultry litter microbial communities. The goal of this study was to use molecular biological methods [denaturing gradient gel electrophoresis (DGGE), community cloning, and quantitative real-time PCR] to characterize general, group-specific and pathogenic microbial communities in alum (10% wt/wt) and non-alum-treated litter. According to quantitative real-time PCR analyses, alum addition to the poultry litter resulted in significant reductions in both Campylobacter jejuni and Escherichia coli concentrations by the end of the first month of the experiment (3 log and 2 log, respectively). The concentrations of Salmonella spp. were below detection (Eubacterium and low %GC gram-positive groups in the alum-treated litters by the end of the first month, with no bands detectable for either group after 8 wk of incubation. Conversely, minimal effects of alum addition were observed in the Actinomycetes community. The most significant shift in the microbial community (based on DGGE analyses) occurred in the fungal population, with a large increase in diversity and abundance within 1 mo of alum addition (1 dominant band on d 0 to 9 dominant bands at 4 wk). Specifically, the incidence of Aspergillus spp. increased from 0 to 50% of the sequences in fungal clone libraries (n = 80) over the course of the experiment. This suggests that the addition of alum to poultry litter potentially shifts the microbial populations from bacterially dominated to dominated by fungi. The ramifications of this shift in dominance are still unknown, and future work will be aimed at characterizing these fungi and elucidating their role in the acidified litter environment.

Product analyses and kinetic studies on gas phase oxidation of the fuel additive ethyl tert-butyl ether and its products; Produktanalysen und Kinetikuntersuchungen der Gasphasenoxidation des Kraftstoffadditivs Ethyl-tert-butylether und seiner Produkte

Energy Technology Data Exchange (ETDEWEB)

Becker, K H; Thuener, L

1997-04-01

The widespread use of the additive ETBE in gasoline leads to an increased release of this compound into the atmosphere via evaporation or exhaust fumes. In order to determine the influence of this additive on trace gas cycles it is first necessary to carry out studies on the degradation mechanisms and pertinent kinetic properties of this substance. The aim of the present study was to examine the degradation mechanisms of the fuel additive t-butyl ethyl ether under atmospheric conditions. The reactions of the main degradation products (t-butyl formiate and t-butyl acetate, together ca. 80%) were also studied in order to obtain as complete a picture of the degradation paths as possible. This was to permit an assessment of the influence of ETBE and its products on tropospheric trace gas cycles and ozone formation. [Deutsch] Bei haeufigem Zusatz von ETBE in Benzin wird diese Verbindung durch Verdampfung oder als Abgas verstaerkt in die Atmosphaere abgegeben. Um den Einfluss des Additivs auf die Spurengas-Kreislaeufe zu bestimmen, sind daher Untersuchungen noetig, um die Abbau-Mechanismen und die zugehoerigen kinetischen Daten zu ermitteln. Das Ziel dieser Arbeit ist die Untersuchung der Abbaumechanismen des Kraftstoffadditivs t-Butylethylether unter atmosphaerischen Bedingungen. Fuer eine moeglichst vollstaendige Analyse des Abbauweges werden auch die Reaktionen der Hauptabbauprodukte (t-Butylformiat und t-Butylacetat, zusammen etwa 80%) untersucht. Dadurch soll der Einfluss auf troposphaerische Spurengas-Kreislaeufe und auf die Ozonbildung von ETBE und seinen Produkten abgeschaetzt werden. (orig./SR)

Grey literature in meta-analyses of randomized trials of health care interventions.

Science.gov (United States)

Hopewell, S; McDonald, S; Clarke, M; Egger, M

2007-04-18

The inclusion of grey literature (i.e. literature that has not been formally published) in systematic reviews may help to overcome some of the problems of publication bias, which can arise due to the selective availability of data. To review systematically research studies, which have investigated the impact of grey literature in meta-analyses of randomized trials of health care interventions. We searched the Cochrane Methodology Register (The Cochrane Library Issue 3, 2005), MEDLINE (1966 to 20 May 2005), the Science Citation Index (June 2005) and contacted researchers who may have carried out relevant studies. A study was considered eligible for this review if it compared the effect of the inclusion and exclusion of grey literature on the results of a cohort of meta-analyses of randomized trials. Data were extracted from each report independently by two reviewers. The main outcome measure was an estimate of the impact of trials from the grey literature on the pooled effect estimates of the meta-analyses. Information was also collected on the area of health care, the number of meta-analyses, the number of trials, the number of trial participants, the year of publication of the trials, the language and country of publication of the trials, the number and type of grey and published literature, and methodological quality. Five studies met the inclusion criteria. All five studies showed that published trials showed an overall greater treatment effect than grey trials. This difference was statistically significant in one of the five studies. Data could be combined for three of the five studies. This showed that, on average, published trials showed a 9% greater treatment effect than grey trials (ratio of odds ratios for grey versus published trials 1.09; 95% CI 1.03-1.16). Overall there were more published trials included in the meta-analyses than grey trials (median 224 (IQR 108-365) versus 45(IQR 40-102)). Published trials had more participants on average. The most

Finite element analyses of continuous filament ties for masonry applications : final report for the Arquin Corporation.

Energy Technology Data Exchange (ETDEWEB)

Quinones, Armando, Sr. (Arquin Corporation, La Luz, NM); Bibeau, Tiffany A.; Ho, Clifford Kuofei

2008-08-01

Finite-element analyses were performed to simulate the response of a hypothetical vertical masonry wall subject to different lateral loads with and without continuous horizontal filament ties laid between rows of concrete blocks. A static loading analysis and cost comparison were also performed to evaluate optimal materials and designs for the spacers affixed to the filaments. Results showed that polypropylene, ABS, and polyethylene (high density) were suitable materials for the spacers based on performance and cost, and the short T-spacer design was optimal based on its performance and functionality. Simulations of vertical walls subject to static loads representing 100 mph winds (0.2 psi) and a seismic event (0.66 psi) showed that the simulated walls performed similarly and adequately when subject to these loads with and without the ties. Additional simulations and tests are required to assess the performance of actual walls with and without the ties under greater loads and more realistic conditions (e.g., cracks, non-linear response).

Fluxional additives: a second generation control in enantioselective catalysis.

Science.gov (United States)

Sibi, Mukund P; Manyem, Shankar; Palencia, Hector

2006-10-25

The concept of "fluxional additives", additives that can adopt enantiomeric conformations depending on the chiral information in the ligand, is demonstrated in enantioselective Diels-Alder and nitrone cycloaddition reactions. The additive design is modular, and diverse structures are accessible in three steps. Chiral Lewis acids from main group and transition metals show enhancements in enantioselectivity in the presence of these additives.

Development of a set of equations for incorporating disk flexibility effects in rotordynamical analyses

Science.gov (United States)

Flowers, George T.; Ryan, Stephen G.

1991-01-01

Rotordynamical equations that account for disk flexibility are developed. These equations employ free-free rotor modes to model the rotor system. Only transverse vibrations of the disks are considered, with the shaft/disk system considered to be torsionally rigid. Second order elastic foreshortening effects that couple with the rotor speed to produce first order terms in the equations of motion are included. The approach developed in this study is readily adaptable for usage in many of the codes that are current used in rotordynamical simulations. The equations are similar to those used in standard rigid disk analyses but with additional terms that include the effects of disk flexibility. An example case is presented to demonstrate the use of the equations and to show the influence of disk flexibility on the rotordynamical behavior of a sample system.

Including Below Detection Limit Samples in Post Decommissioning Soil Sample Analyses

Energy Technology Data Exchange (ETDEWEB)

Kim, Jung Hwan; Yim, Man Sung [KAIST, Daejeon (Korea, Republic of)

2016-05-15

To meet the required standards the site owner has to show that the soil at the facility has been sufficiently cleaned up. To do this one must know the contamination of the soil at the site prior to clean up. This involves sampling that soil to identify the degree of contamination. However there is a technical difficulty in determining how much decontamination should be done. The problem arises when measured samples are below the detection limit. Regulatory guidelines for site reuse after decommissioning are commonly challenged because the majority of the activity in the soil at or below the limit of detection. Using additional statistical analyses of contaminated soil after decommissioning is expected to have the following advantages: a better and more reliable probabilistic exposure assessment, better economics (lower project costs) and improved communication with the public. This research will develop an approach that defines an acceptable method for demonstrating compliance of decommissioned NPP sites and validates that compliance. Soil samples from NPP often contain censored data. Conventional methods for dealing with censored data sets are statistically biased and limited in their usefulness.

On the requirement for remodelling the spent nuclear fuel transportation casks for research reactors. A review of the drop impact analyses of JRC-80Y-20T

International Nuclear Information System (INIS)

2005-07-01

The Japan Atomic Energy Research Institute (JAERI) constructed two stainless steel transportation casks, JRC-80Y-20T, for spent nuclear fuels of research reactors and had utilized them for transportation since 1981. A modification of the design was applied to the United States of America (USA) for transportation of silicide fuels. Additional analyses employing the impact analysis code LS-DYNA that was often used for safety analysis were submitted by the JAERI to the USA in 2003 to show integrity of the packages; the casks were still not approved, because inelastic deformation was occurred on the surface of the lid touching to the body. To resolve this problem on design approval of transportation casks, a review group was formed in June 2004. The group examined the impact analyses by reviewing the input data and performing the sensitivity analyses. As the drop impact analyses were found to be practically reasonable, it was concluded that the approval of the USA for the transportation casks could not be obtained just by revising the analyses; therefore, remodelling the casks is required. (author)

Biocompatibility of photopolymers for additive manufacturing

Directory of Open Access Journals (Sweden)

Leonhardt Stefan

2016-09-01

Full Text Available To establish photopolymers for the production of class II or class III medical products by additive manufacturing it is essential to know which components of photopolymeric systems, consisting of monomers, photoinitiators and additives, are the determining factors on their biocompatible properties. In this study the leachable substances of a cured photopolymeric system were eluted and identified by HPLC-MS detection. In addition the cured photopolymer was testes for cytotoxicity and genotoxicity according to DIN EN ISO 10993 for long time applications. The results showed that uncured residual monomers are the determining factor on the biocompatible properties of the photopolymeric system. Strategies to reduce these residual monomers in the cured photopolymer are presented.

Additive and Interactive Effects on Response Time Distributions in Visual Word Recognition

Science.gov (United States)

Yap, Melvin J.; Balota, David A.

2007-01-01

Across 3 different word recognition tasks, distributional analyses were used to examine the joint effects of stimulus quality and word frequency on underlying response time distributions. Consistent with the extant literature, stimulus quality and word frequency produced additive effects in lexical decision, not only in the means but also in the…

The influence of additional fluors on the retention ability of dough and the technological quality of bakery products

Directory of Open Access Journals (Sweden)

Tatiana Bojňanská

2015-08-01

Full Text Available The work monitored rheofermentation properties of dough prepared from composite flours formed by 70% of wheat flour T650 and the addition of 30%. Three kinds of additions were used, namely spelt flour, amaranth flour and buckwheat flour. To determine rheofermentation properties Rheofermentometer Rhea F4 was used, by means of which the dough development, the production of fermentation gases, retention ability of dough and the activity of used baking yeast were analysed. The best ability to retain formed fermentation gas had wheat flour (control and composite flour with the addition of spelt flour. The composite flour with addition of amaranth flour showed a retention coefficient compared to the control lower by 13%, and the composite flour with addition of buckwheat flour showed a retention coefficient compared to the control reduced by 20%. Control flour and composite flours were then processed in the baking experiment. Based on its results it was possible to evaluate the effect of the addition and retention capacity of dough on the quality of the final products (experimental loaves. The biggest loaf volume (200 cm3 and the optimal vaulting (0.65 were found in the control and a loaf made of composite flour with addition of spelt. Loaf volume, produced from composite flours with the addition of amaranth, and buckwheat was compared to control lower by 18.7%, and 16.3% respectively. The value of vaulting of these products (0.40 can be evaluated as unsatisfactory. Based on the evaluation of results observed by measuring on the rheofermentometer and baking experiment results it can be concluded that a better ability to retain the formed fermentation gas, thus ensuring high volume, had loaves made from wheat flour T650 and composite flour with addition of spelt flour. Based on the findings, it is possible to state that the results of rheofermentometric measurements predict the volume and vaulting of bakery products. By means of Rheofermentometer

Energy and exergy analyses of an integrated solar heat pump system

International Nuclear Information System (INIS)

Suleman, F.; Dincer, I.; Agelin-Chaab, M.

2014-01-01

An integrated solar and heat pump based system for industrial heating is developed in this study. The system comprises heat pump cycle for process heating water and solar energy for another industrial heating process. Comprehensive energy and exergy analyses are performed on the system. These analyses generated some compelling results as expected because of the use of green and environmentally friendly energy sources. The results show that the energy efficiency of the process is 58% while the exergy efficiency is 75%. Energetic COP of the heat pump cycle is 3.54 whereas the exergy efficiency is 42.5%. Moreover, the energetic COP of the system is 2.97 and the exergy efficiency of the system is 35.7%. In the parametric study, a different variation such as changing the temperature and pressure of the condenser also shows positive results. - Highlights: • An integrated system is analysed using renewable energy source which can be used in textile industry. • Energy losses and exergy destructions are calculated at all major components. • Energy and exergy efficiencies of all subunits, subsystems and overall system are determined. • A parametric study shows the effect of environment and operating conditions on efficiencies. • Solar energy for heating in textile industry is efficient and environmentally friendly

Coalescent-based genome analyses resolve the early branches of the euarchontoglires.

Directory of Open Access Journals (Sweden)

Vikas Kumar

Full Text Available Despite numerous large-scale phylogenomic studies, certain parts of the mammalian tree are extraordinarily difficult to resolve. We used the coding regions from 19 completely sequenced genomes to study the relationships within the super-clade Euarchontoglires (Primates, Rodentia, Lagomorpha, Dermoptera and Scandentia because the placement of Scandentia within this clade is controversial. The difficulty in resolving this issue is due to the short time spans between the early divergences of Euarchontoglires, which may cause incongruent gene trees. The conflict in the data can be depicted by network analyses and the contentious relationships are best reconstructed by coalescent-based analyses. This method is expected to be superior to analyses of concatenated data in reconstructing a species tree from numerous gene trees. The total concatenated dataset used to study the relationships in this group comprises 5,875 protein-coding genes (9,799,170 nucleotides from all orders except Dermoptera (flying lemurs. Reconstruction of the species tree from 1,006 gene trees using coalescent models placed Scandentia as sister group to the primates, which is in agreement with maximum likelihood analyses of concatenated nucleotide sequence data. Additionally, both analytical approaches favoured the Tarsier to be sister taxon to Anthropoidea, thus belonging to the Haplorrhine clade. When divergence times are short such as in radiations over periods of a few million years, even genome scale analyses struggle to resolve phylogenetic relationships. On these short branches processes such as incomplete lineage sorting and possibly hybridization occur and make it preferable to base phylogenomic analyses on coalescent methods.

Effect of Hypoeutectic Boron Additions on the Grain Size and Mechanical Properties of Ti-6Al-4V Manufactured with Powder Bed Electron Beam Additive Manufacturing

Science.gov (United States)

Mahbooba, Zaynab; West, Harvey; Harrysson, Ola; Wojcieszynski, Andrzej; Dehoff, Ryan; Nandwana, Peeyush; Horn, Timothy

2017-03-01

In additive manufacturing, microstructural control is feasible via processing parameter alteration. However, the window for parameter variation for certain materials, such as Ti-6Al-4V, is limited, and alternative methods must be employed to customize microstructures. Grain refinement and homogenization in cast titanium alloys has been demonstrated through the addition of hypoeutectic concentrations of boron. This work explores the influence of 0.00 wt.%, 0.25 wt.%, 0.50 wt.%, and 1.0 wt.% boron additions on the microstructure and bulk mechanical properties of Ti-6Al-4V samples fabricated in an Arcam A2 electron beam melting (EBM) system with commercial processing parameters for Ti-6Al-4V. Analyses of EBM fabricated Ti-6Al-4V + B indicate that the addition of 0.25-1.0 wt.% boron progressively refines the grain structure, and it improves hardness and elastic modulus. Despite a reduction in size, the β grain structure remained columnar as a result of directional heat transfer during EBM fabrication.

Transient analyses for accelerator driven system PDS-XADS using the extended SIMMER-III code

International Nuclear Information System (INIS)

Suzuki, Tohru; Chen, Xue-Nong; Rineiski, Andrei; Maschek, Werner

2005-01-01

Transient analyses for Preliminary Design Studies of an Experimental Accelerator Driven System (PDS-XADS) were performed with the reactor safety analysis code SIMMER-III, which was originally developed for the safety assessment of sodium-cooled fast reactors and recently extended by the authors so as to describe the XADS specifics such as subcritical core, strong external neutron source and lead-bismuth-eutectic (LBE) coolant. As transient scenarios, the following cases were analyzed in accordance with the PDS-XADS program: spurious beam trip (BT), unprotected beam overpower (UBOP), unprotected transient overpower (UTOP), unprotected loss of flow (ULOF) and unprotected blockage (UBL) in a single fuel assembly. In addition, to cover some core-melt situations and investigate the potential for recriticalities, so-called snap-shot analyses with ad hoc postulated severe blockage conditions were also investigated. The simulation results for BT and UBOP showed that immediate fuel damage might not take place under short-time beam interruption or a 100% increase of the external neutron source. Concerning UTOP, it was found that a reactivity jump of 1 $ would not lead to damage of the fuel and the cladding. The ULOF simulation showed that the remaining natural convection of the coolant would prevent the cladding from disruptions. In the simulation of UBL in a single fuel assembly, it was shown that no cladding failure might be expected, due to the radial heat transfer and the coolant flow in the hexcan gap. Under an artificial suppression of the radial heat transfer for this UBL case, a pin failure occurred in the simulation but subsequent fuel sweep-out into the upper plenum region would bring a reactivity reduction and no power excursion. The severe accident simulations starting from postulated blockage above an already disrupted core showed that a severe recriticality could be avoided by the fuel sweep-out into the dummy-assembly or hexcan gap regions. The present

Food and food additives in severe atopic dermatitis.

Science.gov (United States)

Van Bever, H P; Docx, M; Stevens, W J

1989-11-01

In this study the role of food additives, tyramine and acetylsalicylic acid, was investigated by double-blind placebo-controlled challenges (DBPCC) in 25 children with severe atopic dermatitis (AD). All children challenged with foods (n = 24), except one, showed one or more positive reactions to the DBPCC with foods. Positive reactions presented as different combinations of flares of skin symptoms, intestinal symptoms and respiratory symptoms. Seventeen children (70.8%) showed a positive challenge to egg, 12 to wheat (50%), eight to milk (33.3%) and eight to soya (33.3%). Six children underwent DBPCC with food additives, tyramine and acetylsalicylic acid. All were found to demonstrate positive skin and/or intestinal reactions to at least one of the food additives. Two children reacted to tartrazine, three to sodium benzoate, two to sodium glutamate, two to sodium metabisulfite, four to acetylsalicylic acid and one to tyramine. It is concluded that some foods, food additives, tyramine and acetylsalicylic acid, can cause positive DBPCC in children with severe AD.

Areas V1 and V2 show microsaccade-related 3-4-Hz covariation in gamma power and frequency.

Science.gov (United States)

Lowet, E; Roberts, M J; Bosman, C A; Fries, P; De Weerd, P

2016-05-01

Neuronal gamma-band synchronization (25-80 Hz) in visual cortex appears sustained and stable during prolonged visual stimulation when investigated with conventional averages across trials. However, recent studies in macaque visual cortex have used single-trial analyses to show that both power and frequency of gamma oscillations exhibit substantial moment-by-moment variation. This has raised the question of whether these apparently random variations might limit the functional role of gamma-band synchronization for neural processing. Here, we studied the moment-by-moment variation in gamma oscillation power and frequency, as well as inter-areal gamma synchronization, by simultaneously recording local field potentials in V1 and V2 of two macaque monkeys. We additionally analyzed electrocorticographic V1 data from a third monkey. Our analyses confirm that gamma-band synchronization is not stationary and sustained but undergoes moment-by-moment variations in power and frequency. However, those variations are neither random and nor a possible obstacle to neural communication. Instead, the gamma power and frequency variations are highly structured, shared between areas and shaped by a microsaccade-related 3-4-Hz theta rhythm. Our findings provide experimental support for the suggestion that cross-frequency coupling might structure and facilitate the information flow between brain regions. © 2015 Federation of European Neuroscience Societies and John Wiley & Sons Ltd.

Partial-wave analyses of hadron scattering below 2 GeV

International Nuclear Information System (INIS)

Arndt, R.A.; Roper, L.D.

1990-01-01

The Center for Analysis of Particle Scattering (CAPS) in the Department of Physics at Virginia Polytechnic Institute and State University has analyzed basic two-body hadron reactions below 2 GeV for the last two decades. Reactions studied were nucleon-nucleon, pion-nucleon, K + -nucleon and pion photoproduction systems. In addition to analyses of these systems, a computer graphics system (SAID) has been developed and disseminated to over 200 research institutions using VAX computers. 8 refs

Effect of Additional Structure on Effective Stack Height of Gas Dispersion in Atmosphere

Directory of Open Access Journals (Sweden)

Takenobu Michioka

2016-03-01

Full Text Available Wind-tunnel experiments were conducted to evaluate the effect of additional structure (building, sea wall and banking on the effective stack height, which is usually used in safety analyses of nuclear power facilities in Japan. The effective stack heights were estimated with and without the additional structure in addition to the reactor building while varying several conditions such as the source height, the height of additional structure and the distance between the source position and the additional structure. When the source height is equivalent to the reactor building height, the additional structure enhances both the vertical and horizontal gas dispersion widths and decreases the ground gas concentration, and it means that the additional structure does not decrease the effective stack height. When the source height is larger than the reactor height, the additional structures might affect the effective stack height. As the distance between the source and the additional structure decreases, or as the height of the additional structure increases, the structure has a larger effect on the effective stack height.

Attribute analyses of gpr data for detecting and identifying heavy minerals

Science.gov (United States)

Catakli, Aycan

Attribute analyses have been used successfully in seismic applications for many years. In this study, the application of the attribute analyses to Ground Penetrating Radar (GPR) data has been proposed to detect and identify heavy minerals within the Moon soil (regolith). Lunar samples are mostly composed of heavy minerals such as ilmenite, plagioclase, olivine and pyroxene, a characteristic that makes lunar soil a source for elements such as titanium, oxygen and iron. The main goal of this study is to demonstrate the use of GPR method for detecting and mapping heavy minerals concentrations. The attribute analyses used in this study are Attenuation Analysis (AA), Complex Trace Analysis (CTA), Texture Analysis (TA) and Center Frequency Destitution (CFD). Attribute analysis was applied to both synthetic models and prototype laboratory measurements to study its application to GPR data. The results indicate that the attribute analyses of GPR data can be useful to provide valuable subsurface information. The findings of AA show that attenuation values are function of mineralogy of the subsurface. This could be applicable to Moon and Mars in addition to Earth environment to explore their near-surface soils. CTA can successfully estimate the location of heavy mineral samples embedded inside host medium through the variation of reflected energy around buried sample and sharpen the reflecting interface. Results indicate that as the amount of the buried heavy minerals increases, the value of CTA parameters (Normal distribution of amplitude spectra `NDoAS' and tau-parameter) proportionally increase. TA measures combined can be used as an enhanced interpretation tool. The texture results show that heavy mineral concentrations can be identified by the high contrast, entropy, autocorrelation, correlation, cluster, dissimilarity, standard deviation, variance and low energy, maximum probability, and homogeneity. The measures also help in highlighting the edge of the buried samples

Dolphin shows and interaction programs: benefits for conservation education?

Science.gov (United States)

Miller, L J; Zeigler-Hill, V; Mellen, J; Koeppel, J; Greer, T; Kuczaj, S

2013-01-01

Dolphin shows and dolphin interaction programs are two types of education programs within zoological institutions used to educate visitors about dolphins and the marine environment. The current study examined the short- and long-term effects of these programs on visitors' conservation-related knowledge, attitude, and behavior. Participants of both dolphin shows and interaction programs demonstrated a significant short-term increase in knowledge, attitudes, and behavioral intentions. Three months following the experience, participants of both dolphin shows and interaction programs retained the knowledge learned during their experience and reported engaging in more conservation-related behaviors. Additionally, the number of dolphin shows attended in the past was a significant predictor of recent conservation-related behavior suggesting that repetition of these types of experiences may be important in inspiring people to conservation action. These results suggest that both dolphin shows and dolphin interaction programs can be an important part of a conservation education program for visitors of zoological facilities. © 2012 Wiley Periodicals, Inc.

Analysing the impact of renewable electricity support schemes on power prices: The case of wind electricity in Spain

International Nuclear Information System (INIS)

Saenz de Miera, Gonzalo; Rio Gonzalez, Pablo del; Vizcaino, Ignacio

2008-01-01

It is sometimes argued that renewables are 'expensive'. However, although it is generally true that the private costs of renewable electricity generation are certainly above those of conventional electricity, that statement fails to consider the social benefits provided by electricity from renewable energy sources (RES-E), including environmental and socioeconomic ones. This paper empirically analyses an additional albeit usually neglected benefit: the reduction in the wholesale price of electricity as a result of more RES-E generation being fed into the grid. The case of wind generation in Spain shows that this reduction is greater than the increase in the costs for the consumers arising from the RES-E support scheme (the feed-in tariffs), which are charged to the final consumer. Therefore, a net reduction in the retail electricity price results, which is positive from a consumer point of view. This provides an additional argument for RES-E support and contradicts one of the usual arguments against RES-E deployment: the excessive burden on the consumer

Improving Rural Women Income through Cocoyam Value Addition ...

African Journals Online (AJOL)

User

empowered rural women to become entrepreneurs at various levels. ... have showed that value added agriculture can be one way to preserve small farmers .... The results in Table 2 show the level of utilization of cocoyam value addition.

Trace element analyses of fluid inclusions using laser ablation ICP-MS

Directory of Open Access Journals (Sweden)

Cong-ying Li

2018-03-01

Full Text Available Fluid inclusions are records of the physico-chemical conditions of fluid–rock interactions during magmatism, mineralization and fluid percolation and mixing processes. Laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS is a powerful tool for in situ analyses of small samples at micrometer levels. Here we report in situ analyses of fluid inclusions using LA-ICP-MS method. NIST SRM glasses and 23Na are generally used as external and internal standards for LA-ICP-MS analysis of fluid inclusion, respectively, although the RSD of microthermometric estimation of 23Na is about 20% and even worse, the background signal of Na is high for most ICP-MS. Using well-characterized natural fluids inclusion, we show that RESOlution S-155 laser system analyze fluid inclusions in quartz and determine the trace element concentrations. Resonetics RESOlution S-155 laser has the advantage of the motorized Z stage can be used to accommodate variation of sample height or sample topography and height difference between samples, which is very important for analyzing the fluid inclusion in quartz. Our results suggest laser energy density is 25 J/cm2, laser pulse repetition rates are commonly between 6 and 10 Hz to avoid the fissuring of quartz and obtain adequate results. For this LA-ICP-MS analysis, uncertainty on 35Cl content is around 40% because of intensity of the 35Cl signal is three orders of magnitude less intense than the intensity of the 23Na signal. Nevertheless, it is still a useful reference for fluid inclusion analyses in addition to 23Na. This technique can be applied to a range of hydrothermal geology problems, including determining the origins of ore forming brines and ore deposition processes, mapping metamorphic and hydrothermal fluid provinces and pathways, and constraining the effects of fluid–rock reactions and fluid mixing.

MILROY, Lesley. Observing and Analysing Natural Language: A Critical Account of Sociolinguistic Method. Oxford: Basil Blackwell, 1987. 230pp. MILROY, Lesley. Observing and Analysing Natural Language: A Critical Account of Sociolinguistic Method. Oxford: Basil Blackwell, 1987. 230pp.

Directory of Open Access Journals (Sweden)

Iria Werlang Garcia

2008-04-01

Full Text Available Lesley Milroy's Observing and Analysing Natural Language is a recent addition to an ever growing number of publications in the field of Sociolinguistics. It carries the weight of one of the experienced authors in the current days in the specified field and should offer basic information to both newcomers and established investigators in natural language. Lesley Milroy's Observing and Analysing Natural Language is a recent addition to an ever growing number of publications in the field of Sociolinguistics. It carries the weight of one of the experienced authors in the current days in the specified field and should offer basic information to both newcomers and established investigators in natural language.

Men and women show similar survival outcome in stage IV breast cancer.

Science.gov (United States)

Wu, San-Gang; Zhang, Wen-Wen; Liao, Xu-Lin; Sun, Jia-Yuan; Li, Feng-Yan; Su, Jing-Jun; He, Zhen-Yu

2017-08-01

To evaluate the clinicopathological features, patterns of distant metastases, and survival outcome between stage IV male breast cancer (MBC) and female breast cancer (FBC). Patients diagnosed with stage IV MBC and FBC between 2010 and 2013 were included using the Surveillance, Epidemiology, and End Results program. Univariate and multivariate Cox regression analyses were used to analyze risk factors for overall survival (OS). A total of 4997 patients were identified, including 60 MBC and 4937 FBC. Compared with FBC, patients with MBC were associated with a significantly higher rate of estrogen receptor-positive, progesterone receptor-positive, unmarried, lung metastases, and a lower frequency of liver metastases. Univariate and multivariate analyses showed no significant difference in OS between MBC and FBC. In the propensity score-matched population, there was also no difference in survival between MBC and FBC. Multivariate analysis of MBC showed that OS was longer for patients aged 50-69 years and with estrogen receptor-positive disease. There was no significant difference in survival outcome between stage IV MBC and FBC, but significant differences in clinicopathological features and patterns of metastases between the genders. Copyright © 2017 Elsevier Ltd. All rights reserved.

Re-evaluation of a novel approach for quantitative myocardial oedema detection by analysing tissue inhomogeneity in acute myocarditis using T2-mapping

Energy Technology Data Exchange (ETDEWEB)

Baessler, Bettina; Treutlein, Melanie; Maintz, David; Bunck, Alexander C. [University Hospital of Cologne, Department of Radiology, Cologne (Germany); Schaarschmidt, Frank [Leibniz Universitaet Hannover, Institute of Biostatistics, Faculty of Natural Sciences, Hannover (Germany); Stehning, Christian [Philips Research, Hamburg (Germany); Schnackenburg, Bernhard [Philips, Healthcare Germany, Hamburg (Germany); Michels, Guido [University Hospital of Cologne, Department III of Internal Medicine, Heart Centre, Cologne (Germany)

2017-12-15

To re-evaluate a recently suggested approach of quantifying myocardial oedema and increased tissue inhomogeneity in myocarditis by T2-mapping. Cardiac magnetic resonance data of 99 patients with myocarditis were retrospectively analysed. Thirthy healthy volunteers served as controls. T2-mapping data were acquired at 1.5 T using a gradient-spin-echo T2-mapping sequence. T2-maps were segmented according to the 16-segments AHA-model. Segmental T2-values, segmental pixel-standard deviation (SD) and the derived parameters maxT2, maxSD and madSD were analysed and compared to the established Lake Louise criteria (LLC). A re-estimation of logistic regression models revealed that all models containing an SD-parameter were superior to any model containing global myocardial T2. Using a combined cut-off of 1.8 ms for madSD + 68 ms for maxT2 resulted in a diagnostic sensitivity of 75% and specificity of 80% and showed a similar diagnostic performance compared to LLC in receiver-operating-curve analyses. Combining madSD, maxT2 and late gadolinium enhancement (LGE) in a model resulted in a superior diagnostic performance compared to LLC (sensitivity 93%, specificity 83%). The results show that the novel T2-mapping-derived parameters exhibit an additional diagnostic value over LGE with the inherent potential to overcome the current limitations of T2-mapping. (orig.)

Re-evaluation of a novel approach for quantitative myocardial oedema detection by analysing tissue inhomogeneity in acute myocarditis using T2-mapping

International Nuclear Information System (INIS)

Baessler, Bettina; Treutlein, Melanie; Maintz, David; Bunck, Alexander C.; Schaarschmidt, Frank; Stehning, Christian; Schnackenburg, Bernhard; Michels, Guido

2017-01-01

To re-evaluate a recently suggested approach of quantifying myocardial oedema and increased tissue inhomogeneity in myocarditis by T2-mapping. Cardiac magnetic resonance data of 99 patients with myocarditis were retrospectively analysed. Thirthy healthy volunteers served as controls. T2-mapping data were acquired at 1.5 T using a gradient-spin-echo T2-mapping sequence. T2-maps were segmented according to the 16-segments AHA-model. Segmental T2-values, segmental pixel-standard deviation (SD) and the derived parameters maxT2, maxSD and madSD were analysed and compared to the established Lake Louise criteria (LLC). A re-estimation of logistic regression models revealed that all models containing an SD-parameter were superior to any model containing global myocardial T2. Using a combined cut-off of 1.8 ms for madSD + 68 ms for maxT2 resulted in a diagnostic sensitivity of 75% and specificity of 80% and showed a similar diagnostic performance compared to LLC in receiver-operating-curve analyses. Combining madSD, maxT2 and late gadolinium enhancement (LGE) in a model resulted in a superior diagnostic performance compared to LLC (sensitivity 93%, specificity 83%). The results show that the novel T2-mapping-derived parameters exhibit an additional diagnostic value over LGE with the inherent potential to overcome the current limitations of T2-mapping. (orig.)

Fungal communities in wheat grain show significant co-existence patterns among species

DEFF Research Database (Denmark)

Nicolaisen, M.; Justesen, A. F.; Knorr, K.

2014-01-01

identified as ‘core’ OTUs as they were found in all or almost all samples and accounted for almost 99 % of all sequences. The remaining OTUs were only sporadically found and only in small amounts. Cluster and factor analyses showed patterns of co-existence among the core species. Cluster analysis grouped...... the 21 core OTUs into three clusters: cluster 1 consisting of saprotrophs, cluster 2 consisting mainly of yeasts and saprotrophs and cluster 3 consisting of wheat pathogens. Principal component extraction showed that the Fusarium graminearum group was inversely related to OTUs of clusters 1 and 2....

Additivity vs Synergism: Investigation of the Additive Interaction of Cinnamon Bark Oil and Meropenem in Combinatory Therapy.

Science.gov (United States)

Yang, Shun-Kai; Yusoff, Khatijah; Mai, Chun-Wai; Lim, Wei-Meng; Yap, Wai-Sum; Lim, Swee-Hua Erin; Lai, Kok-Song

2017-11-04

Combinatory therapies have been commonly applied in the clinical setting to tackle multi-drug resistant bacterial infections and these have frequently proven to be effective. Specifically, combinatory therapies resulting in synergistic interactions between antibiotics and adjuvant have been the main focus due to their effectiveness, sidelining the effects of additivity, which also lowers the minimal effective dosage of either antimicrobial agent. Thus, this study was undertaken to look at the effects of additivity between essential oils and antibiotic, via the use of cinnamon bark essential oil (CBO) and meropenem as a model for additivity. Comparisons between synergistic and additive interaction of CBO were performed in terms of the ability of CBO to disrupt bacterial membrane, via zeta potential measurement, outer membrane permeability assay and scanning electron microscopy. It has been found that the additivity interaction between CBO and meropenem showed similar membrane disruption ability when compared to those synergistic combinations which was previously reported. Hence, results based on our studies strongly suggest that additive interaction acts on a par with synergistic interaction. Therefore, further investigation in additive interaction between antibiotics and adjuvant should be performed for a more in depth understanding of the mechanism and the impacts of such interaction.

Additivity vs Synergism: Investigation of the Additive Interaction of Cinnamon Bark Oil and Meropenem in Combinatory Therapy

Directory of Open Access Journals (Sweden)

Shun-Kai Yang

2017-11-01

Full Text Available Combinatory therapies have been commonly applied in the clinical setting to tackle multi-drug resistant bacterial infections and these have frequently proven to be effective. Specifically, combinatory therapies resulting in synergistic interactions between antibiotics and adjuvant have been the main focus due to their effectiveness, sidelining the effects of additivity, which also lowers the minimal effective dosage of either antimicrobial agent. Thus, this study was undertaken to look at the effects of additivity between essential oils and antibiotic, via the use of cinnamon bark essential oil (CBO and meropenem as a model for additivity. Comparisons between synergistic and additive interaction of CBO were performed in terms of the ability of CBO to disrupt bacterial membrane, via zeta potential measurement, outer membrane permeability assay and scanning electron microscopy. It has been found that the additivity interaction between CBO and meropenem showed similar membrane disruption ability when compared to those synergistic combinations which was previously reported. Hence, results based on our studies strongly suggest that additive interaction acts on a par with synergistic interaction. Therefore, further investigation in additive interaction between antibiotics and adjuvant should be performed for a more in depth understanding of the mechanism and the impacts of such interaction.

Additive Interaction between Heterogeneous Environmental Quality Domains (Air, Water, Land, Sociodemographic, and Built Environment) on Preterm Birth.

Science.gov (United States)

Grabich, Shannon C; Rappazzo, Kristen M; Gray, Christine L; Jagai, Jyotsna S; Jian, Yun; Messer, Lynne C; Lobdell, Danelle T

2016-01-01

Environmental exposures often occur in tandem; however, epidemiological research often focuses on singular exposures. Statistical interactions among broad, well-characterized environmental domains have not yet been evaluated in association with health. We address this gap by conducting a county-level cross-sectional analysis of interactions between Environmental Quality Index (EQI) domain indices on preterm birth in the Unites States from 2000 to 2005. The EQI, a county-level index constructed for the 2000-2005 time period, was constructed from five domain-specific indices (air, water, land, built, and sociodemographic) using principal component analyses. County-level preterm birth rates ( n  = 3141) were estimated using live births from the National Center for Health Statistics. Linear regression was used to estimate prevalence differences (PDs) and 95% confidence intervals (CIs) comparing worse environmental quality to the better quality for each model for (a) each individual domain main effect, (b) the interaction contrast, and (c) the two main effects plus interaction effect (i.e., the "net effect") to show departure from additivity for the all U.S. counties. Analyses were also performed for subgroupings by four urban/rural strata. We found the suggestion of antagonistic interactions but no synergism, along with several purely additive (i.e., no interaction) associations. In the non-stratified model, we observed antagonistic interactions, between the sociodemographic/air domains [net effect (i.e., the association, including main effects and interaction effects) PD: -0.004 (95% CI: -0.007, 0.000), interaction contrast: -0.013 (95% CI: -0.020, -0.007)] and built/air domains [net effect PD: 0.008 (95% CI 0.004, 0.011), interaction contrast: -0.008 (95% CI: -0.015, -0.002)]. Most interactions were between the air domain and other respective domains. Interactions differed by urbanicity, with more interactions observed in non-metropolitan regions. Observed

Additive interaction between heterogeneous environmental quality domains (air, water, land, sociodemographic and built environment on preterm birth

Directory of Open Access Journals (Sweden)

Shannon Grabich

2016-10-01

Full Text Available BACKGROUND Environmental exposures often occur in tandem; however, epidemiological research often focuses on singular exposures. Statistical interactions among broad, well-characterized environmental domains have not yet been evaluated in association with health. We address this gap by conducting a county-level cross-sectional analysis of interactions between Environmental Quality Index (EQI domain indices on preterm birth in the Unites States from 2000-2005.METHODS: The EQI, a county-level index constructed for the 2000-2005 time period, was constructed from five domain-specific indices (air, water, land, built and sociodemographic using principal component analyses. County-level preterm birth rates (n=3141 were estimated using live births from the National Center for Health Statistics. Linear regression was used to estimate prevalence differences (PD and 95% confidence intervals (CI comparing worse environmental quality to the better quality for each model for a each individual domain main effect b the interaction contrast and c the two main effects plus interaction effect (i.e., the net effect to show departure from additivity for the all U.S counties. Analyses were also performed for subgroupings by four urban/rural strata. RESULTS: We found the suggestion of antagonistic interactions but no synergism, along with several purely additive (i.e., no interaction associations. In the non-stratified model, we observed antagonistic interactions, between the sociodemographic/air domains (net effect (i.e. the association including main effects and interaction effects PD: -0.004 (95% CI:-0.007, 0.000, interaction contrast: -0.013 (95% CI:-0.020, -0.007 and built/air domains (net effect PD: 0.008 (95% CI 0.004, 0.011, interaction contrast: -0.008 (95% CI:-0.015, -0.002. Most interactions were between the air domain and other respective domains. Interactions differed by urbanicity, with more interactions observed in non-metropolitan regions

Stuttering, induced fluency, and natural fluency: a hierarchical series of activation likelihood estimation meta-analyses.

Science.gov (United States)

Budde, Kristin S; Barron, Daniel S; Fox, Peter T

2014-12-01

Developmental stuttering is a speech disorder most likely due to a heritable form of developmental dysmyelination impairing the function of the speech-motor system. Speech-induced brain-activation patterns in persons who stutter (PWS) are anomalous in various ways; the consistency of these aberrant patterns is a matter of ongoing debate. Here, we present a hierarchical series of coordinate-based meta-analyses addressing this issue. Two tiers of meta-analyses were performed on a 17-paper dataset (202 PWS; 167 fluent controls). Four large-scale (top-tier) meta-analyses were performed, two for each subject group (PWS and controls). These analyses robustly confirmed the regional effects previously postulated as "neural signatures of stuttering" (Brown, Ingham, Ingham, Laird, & Fox, 2005) and extended this designation to additional regions. Two smaller-scale (lower-tier) meta-analyses refined the interpretation of the large-scale analyses: (1) a between-group contrast targeting differences between PWS and controls (stuttering trait); and (2) a within-group contrast (PWS only) of stuttering with induced fluency (stuttering state). Copyright © 2014 Elsevier Inc. All rights reserved.

Evaluation of polymer micro parts produced by additive manufacturing processes using vat photopolymerization method

DEFF Research Database (Denmark)

Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

2017-01-01

Micro manufacturing scale feature production by Additive Manufacturing (AM) processes for the direct production of miniaturized polymer components is analysed in this work. The study characterizes the AM processes for polymer micro parts productions using the vat photopolymerization method...

The structure of additive conservation laws

International Nuclear Information System (INIS)

Helmut Reen

1979-01-01

All additive conserved quantities are listed for a system with short range central force interaction between the particles: a special case shows up in Boltzmann H-theorem and his derivation of the Maxwell velocity distribution. It is concluded that in classical mechanics of mass points there are no other additive conservation laws besides of energy, momentum, angular momentum and center of mass motion. A generator is considered of a symmetry transformation defined as integral over a conserved local current density where the latter, in general, needs not be covariant under translations

Estimating required information size by quantifying diversity in random-effects model meta-analyses

DEFF Research Database (Denmark)

Wetterslev, Jørn; Thorlund, Kristian; Brok, Jesper

2009-01-01

an intervention effect suggested by trials with low-risk of bias. METHODS: Information size calculations need to consider the total model variance in a meta-analysis to control type I and type II errors. Here, we derive an adjusting factor for the required information size under any random-effects model meta......-analysis. RESULTS: We devise a measure of diversity (D2) in a meta-analysis, which is the relative variance reduction when the meta-analysis model is changed from a random-effects into a fixed-effect model. D2 is the percentage that the between-trial variability constitutes of the sum of the between...... and interpreted using several simulations and clinical examples. In addition we show mathematically that diversity is equal to or greater than inconsistency, that is D2 >or= I2, for all meta-analyses. CONCLUSION: We conclude that D2 seems a better alternative than I2 to consider model variation in any random...

Coculture with astrocytes reduces the radiosensitivity of glioblastoma stem-like cells and identifies additional targets for radiosensitization

International Nuclear Information System (INIS)

Rath, Barbara H; Wahba, Amy; Camphausen, Kevin; Tofilon, Philip J

2015-01-01

Toward developing a model system for investigating the role of the microenvironment in the radioresistance of glioblastoma (GBM), human glioblastoma stem-like cells (GSCs) were grown in coculture with human astrocytes. Using a trans-well assay, survival analyses showed that astrocytes significantly decreased the radiosensitivity of GSCs compared to standard culture conditions. In addition, when irradiated in coculture, the initial level of radiation-induced γH2AX foci in GSCs was reduced and foci dispersal was enhanced suggesting that the presence of astrocytes influenced the induction and repair of DNA double-strand breaks. These data indicate that astrocytes can decrease the radiosensitivity of GSCs in vitro via a paracrine-based mechanism and further support a role for the microenvironment as a determinant of GBM radioresponse. Chemokine profiling of coculture media identified a number of bioactive molecules not present under standard culture conditions. The gene expression profiles of GSCs grown in coculture were significantly different as compared to GSCs grown alone. These analyses were consistent with an astrocyte-mediated modification in GSC phenotype and, moreover, suggested a number of potential targets for GSC radiosensitization that were unique to coculture conditions. Along these lines, STAT3 was activated in GSCs grown with astrocytes; the JAK/STAT3 inhibitor WP1066 enhanced the radiosensitivity of GSCs under coculture conditions and when grown as orthotopic xenografts. Further, this coculture system may also provide an approach for identifying additional targets for GBM radiosensitization

The addition of inulin and Lactobacillus casei 01 in sheep milk ice cream.

Science.gov (United States)

Balthazar, Celso F; Silva, Hugo L A; Esmerino, Erick A; Rocha, Ramon S; Moraes, Jeremias; Carmo, Mariana A V; Azevedo, Luciana; Camps, Ihosvany; K D Abud, Yuri; Sant'Anna, Celso; Franco, Robson M; Freitas, Mônica Q; Silva, Marcia C; Raices, Renata S L; Escher, Graziela B; Granato, Daniel; Senaka Ranadheera, C; Nazarro, Filomena; Cruz, Adriano G

2018-04-25

The effect of the Lactobacillus casei 01 and inulin addition on sheep milk ice cream during storage (-18 °C, 150 days) was investigated. Control, probiotic and synbiotic ice cream (10% w/w sheep milk cream; 10% w/w sheep milk cream, L. casei 01, 6 log CFU/mL; 10% w/w inulin, L. casei 01, 6 log CFU/mL, respectively) were manufactured. Microbiological counts (probiotic count, survival after in vitro gastrointestinal resistance, Caco-2 cell adhesion), bioactivity and microstructure were analysed. Physical and textural characteristics, colour parameters, thermal analysis and organic acids/volatile compounds were also evaluated. All formulations supported L. casei 01 viability and maintained above the minimum therapeutic level (>6 log CFU/mL) during storage. Inulin did not affect L. casei 01 survival after the passage through simulated gastrointestinal tract and adhesion to Caco-2 cells while improved the ACE-inhibitory and antioxidant activity. L. casei 01 addition produced several volatile compounds, such as carboxylic acids, alcohols, aldehydes and ketones. Also, scanning electron microscopy showed an interaction between probiotic bacteria and inulin fibre on synbiotic ice cream and the adhesion of L. casei to Caco-2 cells was observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

TG/FT-IR characterization of additives typically employed in EPDM formulations

Directory of Open Access Journals (Sweden)

Natália Beck Sanches

2015-06-01

Full Text Available AbstractThermogravimetric analysis coupled to Fourier transform infrared spectroscopy (TG/FT-IR is a very popular technique for rubbers characterization. It involves analyses of the base polymer and additives. Ethylene–propylene–diene (EPDM rubbers are frequently investigated by TG/FT-IR; however, the focus has been the degradation temperature range of the polymer. In this study, unvulcanized and vulcanized EPDM rubber and its additives were investigated by TG/FT-IR, without solvent extraction, and in a wide temperature range. Initially, the additives were individually characterized. TG/FT-IR identified the characteristic groups of all the additives analyzed and distinguished them from each other. Afterwards, unvulcanized and vulcanized EPDM rubbers were investigated without prior extraction.TG/FT-IR detected absorptions due to the additives tetramethylthiuram monosulfide and 2-mercaptobenzothiazole. Both of these sulfur-containing additives were present in the EPDM formulation at concentrations of 0.7 phr (0.63 wt %. The TG/FT-IR technique had some limitations, because not all the additives in EPDM rubber were detected. Paraffin oil, stearic acid and 2,2,4-trimethyl-1,2-dihydroquinoline functional groups were not observed in either the unvulcanized or vulcanized EPDM. Nevertheless, in addition to the ability of this method to detect sulfur-containing groups, the lack of a pre-extraction reduces the time and effort required for additive analysis in rubbers.

Laser additive manufacturing of high-performance materials

CERN Document Server

Gu, Dongdong

2015-01-01

This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization, and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering, and mechanical engineering. This is a book for researchers, students, practicing engineers, and manufacturing industry professionals interested i...

Radiocarbon analyses along the EDML ice core in Antarctica

NARCIS (Netherlands)

van de Wal, R.S.W.; Meijer, H.A.J.; van Rooij, M.; van der Veen, C.

2007-01-01

Samples, 17 in total, from the EDML core drilled at Kohnen station Antarctica are analysed for 14CO and 14CO2 with a dry-extraction technique in combination with accelerator mass spectrometry. Results of the in situ produced 14CO fraction show a very low concentration of in situ produced 14CO.

Radiocarbon analyses along the EDML ice core in Antarctica

NARCIS (Netherlands)

Van de Wal, R. S. W.; Meijer, H. A. J.; De Rooij, M.; Van der Veen, C.

Samples, 17 in total, from the EDML core drilled at Kohnen station Antarctica are analysed for (CO)-C-14 and (CO2)-C-14 with a dry-extraction technique in combination with accelerator mass spectrometry. Results of the in situ produced (CO)-C-14 fraction show a very low concentration of in situ

Integrated tokamak modelling with the fast-ion Fokker–Planck solver adapted for transient analyses

International Nuclear Information System (INIS)

Toma, M; Hamamatsu, K; Hayashi, N; Honda, M; Ide, S

2015-01-01

Integrated tokamak modelling that enables the simulation of an entire discharge period is indispensable for designing advanced tokamak plasmas. For this purpose, we extend the integrated code TOPICS to make it more suitable for transient analyses in the fast-ion part. The fast-ion Fokker–Planck solver is integrated into TOPICS at the same level as the bulk transport solver so that the time evolutions of the fast ion and the bulk plasma are consistent with each other as well as with the equilibrium magnetic field. The fast-ion solver simultaneously handles neutral beam-injected ions and alpha particles. Parallelisation of the fast-ion solver in addition to its computational lightness owing to a dimensional reduction in the phase space enables transient analyses for long periods in the order of tens of seconds. The fast-ion Fokker–Planck calculation is compared and confirmed to be in good agreement with an orbit following a Monte Carlo calculation. The integrated code is applied to ramp-up simulations for JT-60SA and ITER to confirm its capability and effectiveness in transient analyses. In the integrated simulations, the coupled evolution of the fast ions, plasma profiles, and equilibrium magnetic fields are presented. In addition, the electric acceleration effect on fast ions is shown and discussed. (paper)

Additional methodology development for statistical evaluation of reactor safety analyses

International Nuclear Information System (INIS)

Marshall, J.A.; Shore, R.W.; Chay, S.C.; Mazumdar, M.

1977-03-01

The project described is motivated by the desire for methods to quantify uncertainties and to identify conservatisms in nuclear power plant safety analysis. The report examines statistical methods useful for assessing the probability distribution of output response from complex nuclear computer codes, considers sensitivity analysis and several other topics, and also sets the path for using the developed methods for realistic assessment of the design basis accident

Controlling the microstructure and properties of wire arc additive manufactured Ti–6Al–4V with trace boron additions

International Nuclear Information System (INIS)

Bermingham, M.J.; Kent, D.; Zhan, H.; StJohn, D.H.; Dargusch, M.S.

2015-01-01

This study demonstrates that trace boron addition to Ti–6Al–4V coupons produced by additive layer manufacturing is an effective way to eliminate the deleterious anisotropic microstructures often encountered with this manufacturing technique. Trace boron additions (up to 0.13 wt.%) to this alloy eliminate grain boundary-α and colony-α, and instead produce a homogeneous α-microstructure consisting of fine equiaxed α-grains in both as-deposited and heat treated coupons. Prior-β grains remain columnar with boron addition but become narrower due to the wider solidification range and growth restricting effect of the boron solute. Compared to unmodified Ti–6Al–4V alloy, Ti–6Al–4V modified with trace boron additions showed up to 40% improvement in plasticity with no loss in strength under uniaxial compression at room temperature. Boron additions were found to inhibit twinning transmission that causes sudden large load drops during deformation of the unmodified Ti–6Al–4V alloy in the heat treated condition

Additives for rapeseed oil fuel. Influence on the exhaust gas emissions

Energy Technology Data Exchange (ETDEWEB)

Kastl, Johannes; Remmele, Edgar; Thuneke, Klaus [Technologie- und Foerderzentrum, Straubing (Germany)

2013-06-01

In contrast to fossil diesel fuel, the use of additives is not common in rapeseed oil fuel. In a preceding research project the efficacy of several additives, that are commercially available for the use in fossil diesel or FAME, has been investigated for rapeseed oil fuel in the lab. Four additives could be identified, which have a significant influence on the ignition delay or the low temperature flow behaviour of rapeseed oil fuel. To investigate whether there are negative effects of the additives on other fuel-related properties in practical use, a test series on an agricultural tractor capable of running on vegetable oils has been conducted. Attention is focused on the operating parameters like power, torque or fuel consumption as well as on regulated emissions (CO, HC, particulate matter or NOx) and non-regulated emissions like polycyclic aromatic hydrocarbons. Additionally, the influence of the additives on the storage stability of rapeseed oil fuel is investigated in long term studies. No negative influence of the additives on the regulated emissions could be seen in the experiments, the data of the non-regulated emissions is still being analysed. This paper will focus on the emissions testing; results of the long term studies will be given in the presentation. (orig.)

Small GSK-3 Inhibitor Shows Efficacy in a Motor Neuron Disease Murine Model Modulating Autophagy.

Directory of Open Access Journals (Sweden)

Estefanía de Munck

Full Text Available Amyotrophic lateral sclerosis (ALS is a progressive motor neuron degenerative disease that has no effective treatment up to date. Drug discovery tasks have been hampered due to the lack of knowledge in its molecular etiology together with the limited animal models for research. Recently, a motor neuron disease animal model has been developed using β-N-methylamino-L-alanine (L-BMAA, a neurotoxic amino acid related to the appearing of ALS. In the present work, the neuroprotective role of VP2.51, a small heterocyclic GSK-3 inhibitor, is analysed in this novel murine model together with the analysis of autophagy. VP2.51 daily administration for two weeks, starting the first day after L-BMAA treatment, leads to total recovery of neurological symptoms and prevents the activation of autophagic processes in rats. These results show that the L-BMAA murine model can be used to test the efficacy of new drugs. In addition, the results confirm the therapeutic potential of GSK-3 inhibitors, and specially VP2.51, for the disease-modifying future treatment of motor neuron disorders like ALS.

Analysis Of Resistance And Effective Wake Friction Due To Addition Of Stern Tunnels On Passenger Ship Using Cfd

Science.gov (United States)

Chrismianto, D.; Tuswan; Manik, P.

2018-03-01

In this study, the stern tunnel to improve the efficiency of ship propulsion system is analysed. Stern tunnels installed on the two sides of the ship stern. Analysis of ship resistance and wake friction of the ship using CFD are carried out. The stern tunnel height (Hw) and length (L) are implemented to find the better stern tunnel form of the ship. The result of analysis showed that model has a high stern tunnels (Hw) of 1,444 m or additional high stern tunnels ratio of 16% and stern long tunnels (L) about 7 m is a model that has the smallest resistance about 1.1137 N or able to make reduction of resistance amount 11.2582%. While, the model with the addition of height of 0.2 m and a length of 9 m of stern tunnel is a model that has the better advanced speed about 4,927% in increase, and better wake friction about 30.4% in reduce.

Dynamics of energy systems: Methods of analysing technology change

Energy Technology Data Exchange (ETDEWEB)

Neij, Lena

1999-05-01

Technology change will have a central role in achieving a sustainable energy system. This calls for methods of analysing the dynamics of energy systems in view of technology change and policy instruments for effecting and accelerating technology change. In this thesis, such methods have been developed, applied, and assessed. Two types of methods have been considered, methods of analysing and projecting the dynamics of future technology change and methods of evaluating policy instruments effecting technology change, i.e. market transformation programmes. Two methods are focused on analysing the dynamics of future technology change; vintage models and experience curves. Vintage models, which allow for complex analysis of annual streams of energy and technological investments, are applied to the analysis of the time dynamics of electricity demand for lighting and air-distribution in Sweden. The results of the analyses show that the Swedish electricity demand for these purposes could decrease over time, relative to a reference scenario, if policy instruments are used. Experience curves are used to provide insight into the prospects of diffusion of wind turbines and photo voltaic (PV) modules due to cost reduction. The results show potential for considerable cost reduction for wind-generated electricity, which, in turn, could lead to major diffusion of wind turbines. The results also show that major diffusion of PV modules, and a reduction of PV generated electricity down to the level of conventional base-load electricity, will depend on large investments in bringing the costs down (through R D and D, market incentives and investments in niche markets) or the introduction of new generations of PV modules (e.g. high-efficiency mass-produced thin-film cells). Moreover, a model has been developed for the evaluation of market transformation programmes, i.e. policy instruments that effect technology change and the introduction and commercialisation of energy

Design and manufacture of TL analyser by using the microcomputer

International Nuclear Information System (INIS)

Doh, Sih Hong; Woo, Chong Ho

1986-01-01

This paper describes the design of the thermoluminescence analyser using microcomputer. TL analyser is designed to perform the three step heat treatment, such as pre-read heating, readout procedure and post-heating (or pre-irradiation ) anneal. We used a 12-bit A/D converter to get the precise measurement and the phase control method to control the heating temperature. Since the used Apple II microcomputer is cheap and popular, it is possible to design the economical system. Experimental results showed the successful operation with flexibility. The error of temperature control was less than ± 0.2% of the expected value. (Author)

International trade shows: Structure, strategy and performance of exhibitors at individual booths vs. joint booths

DEFF Research Database (Denmark)

Hansen, Kåre

2000-01-01

This paper examines differences in exhibitors who participate at international trade shows at joint booths and those who participate at individual booths. The structure, strategy, and trade show performance of exhibitors at joint booths and those at individual booths are analysed. The analysis...... implications for exhibitors at interna-tional trade shows and export marketing programmes and other marketing programmes offering services to international trade show exhibitors....... of exhibitors at the international food shows SIAL (Paris) and ANUGA (Cologne) showed several significant differences with regard to structure and strategy. However, no significant differences in the performance assessments between the two partici-pation modes were found. The findings have important...

Microbiological Evaluation of Household Drinking Water Treatment in Rural China Shows Benefits of Electric Kettles: A Cross-Sectional Study

Science.gov (United States)

Cohen, Alasdair; Tao, Yong; Luo, Qing; Zhong, Gemei; Romm, Jeff; Colford, John M.; Ray, Isha

2015-01-01

Background In rural China ~607 million people drink boiled water, yet little is known about prevailing household water treatment (HWT) methods or their effectiveness. Boiling, the most common HWT method globally, is microbiologically effective, but household air pollution (HAP) from burning solid fuels causes cardiovascular and respiratory disease, and black carbon emissions exacerbate climate change. Boiled water is also easily re-contaminated. Our study was designed to identify the HWT methods used in rural China and to evaluate their effectiveness. Methods We used a geographically stratified cross-sectional design in rural Guangxi Province to collect survey data from 450 households in the summer of 2013. Household drinking water samples were collected and assayed for Thermotolerant Coliforms (TTC), and physicochemical analyses were conducted for village drinking water sources. In the winter of 2013–2104, we surveyed 120 additional households and used remote sensors to corroborate self-reported boiling data. Findings Our HWT prevalence estimates were: 27.1% boiling with electric kettles, 20.3% boiling with pots, 34.4% purchasing bottled water, and 18.2% drinking untreated water (for these analyses we treated bottled water as a HWT method). Households using electric kettles had the lowest concentrations of TTC (73% lower than households drinking untreated water). Multilevel mixed-effects regression analyses showed that electric kettles were associated with the largest Log10TTC reduction (-0.60, pwater (-0.45, pwater, electric kettle users also had the lowest risk of having TTC detected in their drinking water (risk ratio, RR = 0.49, 0.34–0.70, pwater users (RR = 0.70, 0.53–0.93, pwater access and reduce HAP exposure in rural China. PMID:26421716

Precise Chemical Analyses of Planetary Surfaces

Science.gov (United States)

Kring, David; Schweitzer, Jeffrey; Meyer, Charles; Trombka, Jacob; Freund, Friedemann; Economou, Thanasis; Yen, Albert; Kim, Soon Sam; Treiman, Allan H.; Blake, David;

Global transcriptional, physiological and metabolite analyses of Desulfovibrio vulgaris Hildenborough responses to salt adaptation

Energy Technology Data Exchange (ETDEWEB)

He, Z.; Zhou, A.; Baidoo, E.; He, Q.; Joachimiak, M. P.; Benke, P.; Phan, R.; Mukhopadhyay, A.; Hemme, C.L.; Huang, K.; Alm, E.J.; Fields, M.W.; Wall, J.; Stahl, D.; Hazen, T.C.; Keasling, J.D.; Arkin, A.P.; Zhou, J.

2009-12-01

The response of Desulfovibrio vulgaris Hildenborough to salt adaptation (long-term NaCl exposure) was examined by physiological, global transcriptional, and metabolite analyses. The growth of D. vulgaris was inhibited by high levels of NaCl, and the growth inhibition could be relieved by the addition of exogenous amino acids (e.g., glutamate, alanine, tryptophan) or yeast extract. Salt adaptation induced the expression of genes involved in amino acid biosynthesis and transport, electron transfer, hydrogen oxidation, and general stress responses (e.g., heat shock proteins, phage shock proteins, and oxidative stress response proteins). Genes involved in carbon metabolism, cell motility, and phage structures were repressed. Comparison of transcriptomic profiles of D. vulgaris responses to salt adaptation with those of salt shock (short-term NaCl exposure) showed some similarity as well as a significant difference. Metabolite assays showed that glutamate and alanine were accumulated under salt adaptation, suggesting that they may be used as osmoprotectants in D. vulgaris. A conceptual model is proposed to link the observed results to currently available knowledge for further understanding the mechanisms of D. vulgaris adaptation to elevated NaCl.

Influence of lead oxide addition on LnTiTaO6 (Ln = Ce, Pr and Nd) microwave ceramics

International Nuclear Information System (INIS)

Padma Kumar, H.; Thomas, J.K.; John, Annamma; Solomon, Sam

2011-01-01

The effect of PbO addition on the structural, processing and microwave dielectric properties of LnTiTaO 6 (Ln = Ce, Pr and Nd) ceramics are reported. Conventional solid state ceramic route was used for the preparation of samples. Phase pure LnTiTaO 6 (Ln = Ce, Pr and Nd) ceramics are prepared at a calcination temperature of 1300 deg C. The samples are sintered at optimized temperatures. Addition of PbO reduces the sintering temperature. The crystal structure of the materials was analysed using X-ray diffraction techniques and the surface morphology of the sintered samples was analysed using scanning electron microscopy. The dielectric constant at microwave frequency range decreases for higher PbO addition for all the samples but the quality factor improves on small PbO addition. The thermal stability of resonant frequency was also improved with PbO addition on all the systems. A number of samples with improved microwave dielectric properties were obtained on all the systems suitable for practical applications. (author)

Studies on sintering additives for hydroxyapatite, and controlled porosity structures of calcium aluminates and polypropylene-tricalcium phosphate for bone graft applications

Science.gov (United States)

Kalita, Samar Jyoti

Tissue engineering has made a significant contribution in developing new biomaterials that can restore the structural features and physiological functions of natural tissues. Various materials, such as metals, ceramics, polymers and composites have been developed for their use in hard tissue engineering applications. Part A of this thesis describes my research on HAp ceramics. HAp, a bioactive ceramic, is known for its osteoconductivity, but shows poor mechanical performance. This program aimed at improving mechanical performance of synthetic HAp by introducing small quantities of various sintering additives. A range of oxide-based sintering additives were selected and prepared. Dense compacts were prepared using a uniaxial press with an average green density of 1.6 g/cc. Results showed that some of these sintering additives improved densification, hardness and compression strength of synthetic HAp compared to the pure composition. A maximum bulk density of 3.06 g/cc was achieved for 2.5 wt% addition of MgO. A Microhardness of 4.9 GPa (505 HV) was measured for 2.5 wt% addition of BaO, and the highest compression strength (220MPa) was reported for 2.5 wt% addition of CaO. Cytotoxicity and cell proliferation studies with a modified human osteoblast (HOB) cell-line (OPC1) proved most of these materials non-toxic and biocompatible. Microscopic observation revealed that bone cells were attached and grew well on most of these ceramic matrices. Part B describes my work on development of controlled porosity polypropylene-tricalcium phosphate composite scaffolds via the fused deposition modeling (FDM) process. Hg-porosimetry was performed to determine pore size and their distribution. Uniaxial compression testing performed on samples with 36 vol% porosity and pore size of 160 mum showed the best compressive strength of 12.7 MPa. Part C includes my research on development of "3-D honeycomb" porous calcium aluminate structures via the indirect FDM process. Samples of 29% and

Analysing the effectiveness of renewable energy supporting policies in the European Union

Energy Technology Data Exchange (ETDEWEB)

Harmelink, Mirjam [Ecofys BV, P.O. Box 8404, NL-3503 RK Utrecht (Netherlands)] e-mail: m.harmelink@ecofys.nl; Voogt, Monique [Ecofys BV, P.O. Box 8404, NL-3503 RK Utrecht (Netherlands); Cremer, Clemens [Fraunhofer ISI, Breslauer Str. 48, 76139 Karlsruhe (Germany)] e-mail: Cremer@isi.fhg.de

2006-02-01

With several mid-term policies in place to support the development of renewables, the European Union (EU) seems on its way to increasing the share of renewable energy to the targeted 12% by the year 2010. It is however, yet unclear how effective these policies are, which technologies will see the largest growth and which countries will indeed be able to meet their targets. This article discusses a monitoring protocol that was developed to monitor this effectiveness and judge whether targets will be met. In a step-wise approach policy instruments are characterised and analysed, leading to a quantitative assessment of the likely growth in renewable energy production for each individual technology and country in case no policy changes occur. Applying this monitoring protocol at the EU-level we show that with the current policies in place renewable energy production will reach a share of 8-10% in 2010, and the share of electricity production will reach a level of 15-18% of total electricity consumption, whereas the target is 22.5%. Additional policies are clearly needed to achieve the ambitious targets set.

Analysing the effectiveness of renewable energy supporting policies in the European Union

International Nuclear Information System (INIS)

Harmelink, Mirjam; Voogt, Monique; Cremer, Clemens

2006-01-01

With several mid-term policies in place to support the development of renewables, the European Union (EU) seems on its way to increasing the share of renewable energy to the targeted 12% by the year 2010. It is however, yet unclear how effective these policies are, which technologies will see the largest growth and which countries will indeed be able to meet their targets. This article discusses a monitoring protocol that was developed to monitor this effectiveness and judge whether targets will be met. In a step-wise approach policy instruments are characterised and analysed, leading to a quantitative assessment of the likely growth in renewable energy production for each individual technology and country in case no policy changes occur. Applying this monitoring protocol at the EU-level we show that with the current policies in place renewable energy production will reach a share of 8-10% in 2010, and the share of electricity production will reach a level of 15-18% of total electricity consumption, whereas the target is 22.5%. Additional policies are clearly needed to achieve the ambitious targets set

Analysing Protocol Stacks for Services

DEFF Research Database (Denmark)

Gao, Han; Nielson, Flemming; Nielson, Hanne Riis

2011-01-01

We show an approach, CaPiTo, to model service-oriented applications using process algebras such that, on the one hand, we can achieve a certain level of abstraction without being overwhelmed by the underlying implementation details and, on the other hand, we respect the concrete industrial...... standards used for implementing the service-oriented applications. By doing so, we will be able to not only reason about applications at different levels of abstractions, but also to build a bridge between the views of researchers on formal methods and developers in industry. We apply our approach...... to the financial case study taken from Chapter 0-3. Finally, we develop a static analysis to analyse the security properties as they emerge at the level of concrete industrial protocols....

Seismic fragility analyses

International Nuclear Information System (INIS)

Kostov, Marin

2000-01-01

In the last two decades there is increasing number of probabilistic seismic risk assessments performed. The basic ideas of the procedure for performing a Probabilistic Safety Analysis (PSA) of critical structures (NUREG/CR-2300, 1983) could be used also for normal industrial and residential buildings, dams or other structures. The general formulation of the risk assessment procedure applied in this investigation is presented in Franzini, et al., 1984. The probability of failure of a structure for an expected lifetime (for example 50 years) can be obtained from the annual frequency of failure, β E determined by the relation: β E ∫[d[β(x)]/dx]P(flx)dx. β(x) is the annual frequency of exceedance of load level x (for example, the variable x may be peak ground acceleration), P(fI x) is the conditional probability of structure failure at a given seismic load level x. The problem leads to the assessment of the seismic hazard β(x) and the fragility P(fl x). The seismic hazard curves are obtained by the probabilistic seismic hazard analysis. The fragility curves are obtained after the response of the structure is defined as probabilistic and its capacity and the associated uncertainties are assessed. Finally the fragility curves are combined with the seismic loading to estimate the frequency of failure for each critical scenario. The frequency of failure due to seismic event is presented by the scenario with the highest frequency. The tools usually applied for probabilistic safety analyses of critical structures could relatively easily be adopted to ordinary structures. The key problems are the seismic hazard definitions and the fragility analyses. The fragility could be derived either based on scaling procedures or on the base of generation. Both approaches have been presented in the paper. After the seismic risk (in terms of failure probability) is assessed there are several approaches for risk reduction. Generally the methods could be classified in two groups. The

Radiolytic stabilization of poly(methyl methacrylate) using commercial additives

International Nuclear Information System (INIS)

Aquino, Katia Aparecida da Silva

2000-04-01

Poly(methyl methacrylate), PMMA, Acrigel, a Brazilian polymer, is used in the manufacture of medical supplies sterelizable by ionizing radiation. However, when PMMA is gamma-irradiated it undergoes main chain scissions, which promote molecular degradation causing reduction in its mechanical properties. Therefore, radiolytic of PMMA is important for it to become commercially radiosterizable. In this work some commercial additives, originally used in photo-and thermo-oxidate stabilization of polymers, were tested. Only two additives, type HALS (Hindered Amine Light Stabilizer), denoted Scavenger, showed a good protective quality. The investigation of radiation-induced main scissions was carried out by viscosimetric method. The most effective additive, added to the polymer system at 0.3 w/w%, promotes a great molecular radioprotection of 93%. That means a reduction of G-value (scissions/100 eV) from 0.611 to 0.053. In addition, the glassy transition temperature (T g ) of PMMA (no additive) significantly changed by radiation does not change when PMMA (with additive) is irradiated. The spectroscopy analysis, FT-IR and NMR ( 1 H), showed that the radioprotector added to the system does not change the PMMA structure. (author)

77 FR 13522 - Safety Zone; Baltimore Air Show, Patapsco River, Baltimore, MD

Science.gov (United States)

2012-03-07

... public event will consist of military and civilian aircraft performing low-flying, high-speed precision... Harbor. In addition to the air show dates, military and civilian aircraft performing in the air show will...[deg]14'30'' N, longitude 076[deg]36'30'' W; thence to the point of origin. This safety zone will be...

Time dependent patient no-show predictive modelling development.

Science.gov (United States)

Huang, Yu-Li; Hanauer, David A

2016-05-09

Purpose - The purpose of this paper is to develop evident-based predictive no-show models considering patients' each past appointment status, a time-dependent component, as an independent predictor to improve predictability. Design/methodology/approach - A ten-year retrospective data set was extracted from a pediatric clinic. It consisted of 7,291 distinct patients who had at least two visits along with their appointment characteristics, patient demographics, and insurance information. Logistic regression was adopted to develop no-show models using two-thirds of the data for training and the remaining data for validation. The no-show threshold was then determined based on minimizing the misclassification of show/no-show assignments. There were a total of 26 predictive model developed based on the number of available past appointments. Simulation was employed to test the effective of each model on costs of patient wait time, physician idle time, and overtime. Findings - The results demonstrated the misclassification rate and the area under the curve of the receiver operating characteristic gradually improved as more appointment history was included until around the 20th predictive model. The overbooking method with no-show predictive models suggested incorporating up to the 16th model and outperformed other overbooking methods by as much as 9.4 per cent in the cost per patient while allowing two additional patients in a clinic day. Research limitations/implications - The challenge now is to actually implement the no-show predictive model systematically to further demonstrate its robustness and simplicity in various scheduling systems. Originality/value - This paper provides examples of how to build the no-show predictive models with time-dependent components to improve the overbooking policy. Accurately identifying scheduled patients' show/no-show status allows clinics to proactively schedule patients to reduce the negative impact of patient no-shows.

Microcomputer-controlled thermoluminescent analyser IJS MR-200; Mikroracunalniski termoluminescentni analizator IJS MR-200

Energy Technology Data Exchange (ETDEWEB)

Mihelic, M; Miklavzic, U; Rupnik, Z; Satalic, P; Spreizer, F; Zerovnik, I [Institut Jozef Stefan, Ljubljana (Yugoslavia)

1985-07-01

Performances and concept of the multipurpose, microcomputer-controlled thermoluminescent analyser, designed for use in laboratory work TL dosemeters as well as for routine dose readings in the range from ecological to accident doses is described. The main features of the analyser are: time-linear sampling, digitalisation, storing, and subsequent displaying on the monitor time scale of the glow and and temperature curve of the TL material; digital stabilization, control and diagnostic of the analog unit; ability of storing 7 different 8-parametric heating programs; ability of storing 15 evaluation programs defined by 2 or 4 parameters and 3 different algorithms (altogether 5 types of evaluations). Analyser has several features intended for routine work: 9 function keys and possibilities of file forming on cassette or display disc, of dose calculation and averaging, of printing reports with names, and possibility of additional programming in Basic. (author)

POEM: Identifying joint additive effects on regulatory circuits

Directory of Open Access Journals (Sweden)

Maya eBotzman

2016-04-01

Full Text Available Motivation: Expression Quantitative Trait Locus (eQTL mapping tackles the problem of identifying variation in DNA sequence that have an effect on the transcriptional regulatory network. Major computational efforts are aimed at characterizing the joint effects of several eQTLs acting in concert to govern the expression of the same genes. Yet, progress towards a comprehensive prediction of such joint effects is limited. For example, existing eQTL methods commonly discover interacting loci affecting the expression levels of a module of co-regulated genes. Such ‘modularization’ approaches, however, are focused on epistatic relations and thus have limited utility for the case of additive (non-epistatic effects.Results: Here we present POEM (Pairwise effect On Expression Modules, a methodology for identifying pairwise eQTL effects on gene modules. POEM is specifically designed to achieve high performance in the case of additive joint effects. We applied POEM to transcription profiles measured in bone marrow-derived dendritic cells across a population of genotyped mice. Our study reveals widespread additive, trans-acting pairwise effects on gene modules, characterizes their organizational principles, and highlights high-order interconnections between modules within the immune signaling network. These analyses elucidate the central role of additive pairwise effect in regulatory circuits, and provide computational tools for future investigations into the interplay between eQTLs.Availability: The software described in this article is available at csgi.tau.ac.il/POEM/.

Outcomes of an enhancement study with additional psychoeducational sessions for healthy siblings of a child with cancer during inpatient family-oriented rehabilitation.

Science.gov (United States)

Niemitz, Mandy; Goldbeck, Lutz

2018-03-01

Chronic illness of a child puts healthy children of the family at risk of distress. Previous studies have demonstrated that healthy children's psychological symptoms can be reduced when the child knows more about the disease. So far, there is limited evidence of the effectiveness of psychoeducational interventions for healthy children. To compare the effectiveness of an inpatient family-oriented rehabilitation program with vs without additional psychoeducational sessions for healthy children of families with children with cancer. We performed a controlled study in 4 German family-oriented rehabilitation clinics. The outcomes of n = 73 healthy children (mean age: M = 9.55; SD = 3.14; range: 4-18), who participated in 5 additional psychoeducational sessions, were compared with the outcomes of n = 111 healthy children (mean age: M = 8.85; SD = 3.28; range: 4-17), who underwent the usual inpatient rehabilitation program. Primary outcomes were the healthy children's cancer-specific knowledge and their emotional symptoms. Secondary outcomes were family satisfaction and quality of life. Intention-to-treat analyses showed that both groups improved significantly from preintervention to postintervention. Improvements comprised knowledge about cancer (F(1,174) = 11.03, p child with cancer. Additional psycho-educational sessions did not show any substantial additional improvement. Copyright © 2017 John Wiley & Sons, Ltd.

The Most Developmentally Truncated Fishes Show Extensive Hox Gene Loss and Miniaturized Genomes

Science.gov (United States)

Malmstrøm, Martin; Britz, Ralf; Matschiner, Michael; Tørresen, Ole K; Hadiaty, Renny Kurnia; Yaakob, Norsham; Tan, Heok Hui; Jakobsen, Kjetill Sigurd; Salzburger, Walter; Rüber, Lukas

2018-01-01

Abstract The world’s smallest fishes belong to the genus Paedocypris. These miniature fishes are endemic to an extreme habitat: the peat swamp forests in Southeast Asia, characterized by highly acidic blackwater. This threatened habitat is home to a large array of fishes, including a number of miniaturized but also developmentally truncated species. Especially the genus Paedocypris is characterized by profound, organism-wide developmental truncation, resulting in sexually mature individuals of <8 mm in length with a larval phenotype. Here, we report on evolutionary simplification in the genomes of two species of the dwarf minnow genus Paedocypris using whole-genome sequencing. The two species feature unprecedented Hox gene loss and genome reduction in association with their massive developmental truncation. We also show how other genes involved in the development of musculature, nervous system, and skeleton have been lost in Paedocypris, mirroring its highly progenetic phenotype. Further, our analyses suggest two mechanisms responsible for the genome streamlining in Paedocypris in relation to other Cypriniformes: severe intron shortening and reduced repeat content. As the first report on the genomic sequence of a vertebrate species with organism-wide developmental truncation, the results of our work enhance our understanding of genome evolution and how genotypes are translated to phenotypes. In addition, as a naturally simplified system closely related to zebrafish, Paedocypris provides novel insights into vertebrate development. PMID:29684203

The Most Developmentally Truncated Fishes Show Extensive Hox Gene Loss and Miniaturized Genomes.

Science.gov (United States)

Malmstrøm, Martin; Britz, Ralf; Matschiner, Michael; Tørresen, Ole K; Hadiaty, Renny Kurnia; Yaakob, Norsham; Tan, Heok Hui; Jakobsen, Kjetill Sigurd; Salzburger, Walter; Rüber, Lukas

2018-04-01

The world's smallest fishes belong to the genus Paedocypris. These miniature fishes are endemic to an extreme habitat: the peat swamp forests in Southeast Asia, characterized by highly acidic blackwater. This threatened habitat is home to a large array of fishes, including a number of miniaturized but also developmentally truncated species. Especially the genus Paedocypris is characterized by profound, organism-wide developmental truncation, resulting in sexually mature individuals of <8 mm in length with a larval phenotype. Here, we report on evolutionary simplification in the genomes of two species of the dwarf minnow genus Paedocypris using whole-genome sequencing. The two species feature unprecedented Hox gene loss and genome reduction in association with their massive developmental truncation. We also show how other genes involved in the development of musculature, nervous system, and skeleton have been lost in Paedocypris, mirroring its highly progenetic phenotype. Further, our analyses suggest two mechanisms responsible for the genome streamlining in Paedocypris in relation to other Cypriniformes: severe intron shortening and reduced repeat content. As the first report on the genomic sequence of a vertebrate species with organism-wide developmental truncation, the results of our work enhance our understanding of genome evolution and how genotypes are translated to phenotypes. In addition, as a naturally simplified system closely related to zebrafish, Paedocypris provides novel insights into vertebrate development.

Additive manufacturing of tunable lenses

Science.gov (United States)

Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

2017-02-01

Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

Molecular genotyping of Colletotrichum species based on arbitrarily primed PCR, A + T-Rich DNA, and nuclear DNA analyses

Science.gov (United States)

Freeman, S.; Pham, M.; Rodriguez, R.J.

1993-01-01

Molecular genotyping of Colletotrichum species based on arbitrarily primed PCR, A + T-rich DNA, and nuclear DNA analyses. Experimental Mycology 17, 309-322. Isolates of Colletotrichum were grouped into 10 separate species based on arbitrarily primed PCR (ap-PCR), A + T-rich DNA (AT-DNA) and nuclear DNA banding patterns. In general, the grouping of Colletotrichum isolates by these molecular approaches corresponded to that done by classical taxonomic identification, however, some exceptions were observed. PCR amplification of genomic DNA using four different primers allowed for reliable differentiation between isolates of the 10 species. HaeIII digestion patterns of AT-DNA also distinguished between species of Colletotrichum by generating species-specific band patterns. In addition, hybridization of the repetitive DNA element (GcpR1) to genomic DNA identified a unique set of Pst 1-digested nuclear DNA fragments in each of the 10 species of Colletotrichum tested. Multiple isolates of C. acutatum, C. coccodes, C. fragariae, C. lindemuthianum, C. magna, C. orbiculare, C. graminicola from maize, and C. graminicola from sorghum showed 86-100% intraspecies similarity based on ap-PCR and AT-DNA analyses. Interspecies similarity determined by ap-PCR and AT-DNA analyses varied between 0 and 33%. Three distinct banding patterns were detected in isolates of C. gloeosporioides from strawberry. Similarly, three different banding patterns were observed among isolates of C. musae from diseased banana.

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

International Nuclear Information System (INIS)

Moinereau, D.; Faidy, C.; Valeta, M.P.; Bhandari, S.; Guichard, D.

1997-01-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs

Evaluation of fracture mechanics analyses used in RPV integrity assessment regarding brittle fracture

Energy Technology Data Exchange (ETDEWEB)

Moinereau, D [Electricite de France, Dept. MTC, Moret-sur-Loing (France); Faidy, C [Electricite de France, SEPTEN, Villeurbanne (France); Valeta, M P [Commisariat a l` Energie Atomique, Dept. DMT, Gif-sur-Yvette (France); Bhandari, S; Guichard, D [Societe Franco-Americaine de Constructions Atomiques (FRAMATOME), 92 - Paris-La-Defense (France)

1997-09-01

Electricite de France has conducted during these last years some experimental and numerical research programmes in order to evaluate fracture mechanics analyses used in nuclear reactor pressure vessels structural integrity assessment, regarding the risk of brittle fracture. These programmes included cleavage fracture tests on large scale cladded specimens containing subclad flaws with their interpretations by 2D and 3D numerical computations, and validation of finite element codes for pressurized thermal shocks analyses. Four cladded specimens made of ferritic steel A508 C13 with stainless steel cladding, and containing shallow subclad flaws, have been tested in four point bending at very low temperature in order to obtain cleavage failure. The specimen failure was obtained in each case in base metal by cleavage fracture. These tests have been interpreted by two-dimensional and three-dimensional finite element computations using different fracture mechanics approaches (elastic analysis with specific plasticity corrections, elastic-plastic analysis, local approach to cleavage fracture). The failure of specimens are conservatively predicted by different analyses. The comparison between the elastic analyses and elastic-plastic analyses shows the conservatism of specific plasticity corrections used in French RPV elastic analyses. Numerous finite element calculations have also been performed between EDF, CEA and Framatome in order to compare and validate several fracture mechanics post processors implemented in finite element programmes used in pressurized thermal shock analyses. This work includes two-dimensional numerical computations on specimens with different geometries and loadings. The comparisons show a rather good agreement on main results, allowing to validate the finite element codes and their post-processors. (author). 11 refs, 24 figs, 3 tabs.

Radio-toxicological analysis of urine; Analyses radiotoxicologiques urinaires

Energy Technology Data Exchange (ETDEWEB)

Jeanmaire, L.; Jammet, H. [Commissariat a l' energie atomique et aux energies alternatives - CEA (France)

1959-07-01

The article is divided into two parts: general and technical. In the general part, a study of the behaviour of radioisotopes in the organism shows the hazards of internal contamination. In addition, the principle of the different methods for the estimation of this contamination is indicated. The second part, which is purely technical, describes some of the methods for urine analysis used in the S.H.A.R.P. radiotoxicology laboratory at the Saclay Nuclear Research Centre. The techniques relate to {sup 239}Pu, {sup 226}Ra, {sup 90}Sr, natural Th, natural U and {sup 233}U. Reprint of a paper published in Annales de Radiologie, Vol. 2, no. 9-10, p. 703-722, 1959 [French] L'article est divise en deux parties: generalites et techniques. Dans les generalites, l'etude du comportement des radioelements dans l'organisme met en evidence les dangers de la contamination interne. De plus le principe des differents moyens permettant d'apprecier cette contamination est indique. La seconde partie, purement technique, expose un certain nombre de methodes d'analyse urinaire utilisees au laboratoire de radiotoxicologie du S.H.A.R.P. au Centre d'Etudes nucleaires de Saclay. Les techniques concernent {sup 239}Pu, {sup 226}Ra, {sup 90}Sr, Th naturel, U naturel et {sup 233}U. Reproduction d'un article publie dans les Annales de Radiologie, Vol. 2, no. 9-10, p. 703-722, 1959.

[Effect of biochar addition on soil evaporation.

Science.gov (United States)

Xu, Jian; Niu, Wen Quan; Zhang, Ming Zhi; Li, Yuan; Lyu, Wang; Li, Kang-Yong; Zou, Xiao-Yang; Liang, Bo-Hui

2016-11-18

In order to determine the rational amount of biochar application and its effect on soil hydrological processes in arid area, soil column experiments were conducted in the laboratory using three biochar additions (5%, 10% and 15%) and four different biochar types (devaporation. The results showed that the addition of biochar could change the phreatic water recharge, soil water-holding capacity, capillary water upward movement and soil evaporation obviously. But the effects were different depending on the type of biochar raw material and the size of particle. The phreatic water recharge increased with the increasing amount of biochar addition. The addition of biochar could obviously enlarge the soil water-holding capacity and promote the capillary water upward movement rate. This effect was greater when using the material of bamboo charcoal compared with using wood charcoal, while biochar with small particle size had greater impact than that with big particle size. The biochar could effectively restrain the soil evaporation at a low addition amount (5%). But it definitely promoted the soil evaporation if the addition amount was very high. In arid area, biochar addition in appropriate amount could improve soil water retention capacity.

Multivariate analyses of crater parameters and the classification of craters

Science.gov (United States)

Siegal, B. S.; Griffiths, J. C.

1974-01-01

Multivariate analyses were performed on certain linear dimensions of six genetic types of craters. A total of 320 craters, consisting of laboratory fluidization craters, craters formed by chemical and nuclear explosives, terrestrial maars and other volcanic craters, and terrestrial meteorite impact craters, authenticated and probable, were analyzed in the first data set in terms of their mean rim crest diameter, mean interior relief, rim height, and mean exterior rim width. The second data set contained an additional 91 terrestrial craters of which 19 were of experimental percussive impact and 28 of volcanic collapse origin, and which was analyzed in terms of mean rim crest diameter, mean interior relief, and rim height. Principal component analyses were performed on the six genetic types of craters. Ninety per cent of the variation in the variables can be accounted for by two components. Ninety-nine per cent of the variation in the craters formed by chemical and nuclear explosives is explained by the first component alone.

Superplasticity behaviors of Al-Zn-Mg-Zr cold-rolled alloy sheet with minor Sc addition

Energy Technology Data Exchange (ETDEWEB)

Xiang, H. [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China); Pan, Q.L., E-mail: pql2016@126.com [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China); Yu, X.H.; Huang, X.; Sun, X.; Wang, X.D.; Li, M.J.; Yin, Z.M. [School of Materials Science and Engineering, Central South University (Light Alloy Research Institute, Central South University), Changsha 410083 (China); Nonferrous Metal Oriented Advanced Structural Materials and Manufacturing Cooperative Innovation Center, Changsha 410083 (China)

2016-10-31

A refined microstructure of Al-Zn-Mg-Sc-Zr alloy sheet was produced by simple hot and cold rolling to an average grain size of 3 µm. Experiments were completed in electro-fluid servo-fatigue tester and results were investigated by means of optical microscope (OM), scanning electron microscopy (SEM) and transmission electron microscope (TEM). Superplastic deformation was conducted and superplastic ductility of ≥200% was achieved at a testing temperature range from 425 ºC to 500 ºC and relative high strain rate range of 1×10{sup −3} s{sup −1}~1×10{sup −1} s{sup −1}. The maximum elongation of 539% was obtained at 500 ºC and 1×10{sup −2} s{sup −1}. In addition, the scanning electron microscopy (SEM) and transmission electron microscope (TEM) analyses showed that the presence of Al{sub 3} (Sc, Zr) particles in pinning grain boundaries and dislocations had a great influence on the superplastic deformation. The analyses of superplastic test data calculated out the coherent strain rates sensitivity parameter of 0.43 and the average activation energy of 143.762 kJ/mol. The data interpreted that the dominant deformation mechanism was grain boundary sliding controlled by lattice self-diffusion.

Fatty acid composition of commercial vegetable oils from the French market analysed using a long highly polar column

Directory of Open Access Journals (Sweden)

Vingering Nathalie

2010-05-01

Full Text Available The increasing concern for consumed fat by western populations has raised the question of the level and the quality of fat intake, especially the composition of fatty acids (FA and their impact on human health. As a consequence, consumers and nutritionists have requested updated publications on FA composition of food containing fat. In the present study, fourteen different kinds of edible oils (rapeseed, olive, hazelnut, argan, groundnut, grape seed, sesame, sunflower, walnut and organic walnut, avocado, wheat germ, and two combined oils were analysed for FA determination using a BPX-70 60 m highly polar GC column. Oils were classified according to the classification of Dubois et al. (2007, 2008. Monounsaturated FA (MUFA group oils, including rapeseed, olive, hazelnut, and avocado oils, contained mainly oleic acid (OA. Groundnut and argan oils, also rich in MUFA, showed in addition high linoleic acid (LA contents. In the polyunsaturated (PUFA group, grape seed oil presented the highest LA content while sunflower, sesame, and wheat germ oils showed noticeable MUFA amounts in addition to high PUFA contents. Walnut oils, also rich in LA, showed the highest linolenic acid (ALA content. The n-6/n-3 ratio of each oil was calculated. Trans-FA (TFA was also detected and quantified. Results were compared with the data published during the past decade, and the slight discrepancies were attributed to differences in origin and variety of seed-cultivars, and in seed and oil processes.

Recurrent and multiple bladder tumors show conserved expression profiles

International Nuclear Information System (INIS)

Lindgren, David; Fioretos, Thoas; Månsson, Wiking; Höglund, Mattias; Gudjonsson, Sigurdur; Jee, Kowan Ja; Liedberg, Fredrik; Aits, Sonja; Andersson, Anna; Chebil, Gunilla; Borg, Åke; Knuutila, Sakari

2008-01-01

Urothelial carcinomas originate from the epithelial cells of the inner lining of the bladder and may appear as single or as multiple synchronous tumors. Patients with urothelial carcinomas frequently show recurrences after treatment making follow-up necessary. The leading hypothesis explaining the origin of meta- and synchronous tumors assumes a monoclonal origin. However, the genetic relationship among consecutive tumors has been shown to be complex in as much as the genetic evolution does not adhere to the chronological appearance of the metachronous tumors. Consequently, genetically less evolved tumors may appear chronologically later than genetically related but more evolved tumors. Forty-nine meta- or synchronous urothelial tumors from 22 patients were analyzed using expression profiling, conventional CGH, LOH, and mutation analyses. We show by CGH that partial chromosomal losses in the initial tumors may not be present in the recurring tumors, by LOH that different haplotypes may be lost and that detected regions of LOH may be smaller in recurring tumors, and that mutations present in the initial tumor may not be present in the recurring ones. In contrast we show that despite apparent genomic differences, the recurrent and multiple bladder tumors from the same patients display remarkably similar expression profiles. Our findings show that even though the vast majority of the analyzed meta- and synchronous tumors from the same patients are not likely to have originated directly from the preceding tumor they still show remarkably similar expressions profiles. The presented data suggests that an expression profile is established early in tumor development and that this profile is stable and maintained in recurring tumors

AirShow 1.0 CFD Software Users' Guide

Science.gov (United States)

Mohler, Stanley R., Jr.

2005-01-01

AirShow is visualization post-processing software for Computational Fluid Dynamics (CFD). Upon reading binary PLOT3D grid and solution files into AirShow, the engineer can quickly see how hundreds of complex 3-D structured blocks are arranged and numbered. Additionally, chosen grid planes can be displayed and colored according to various aerodynamic flow quantities such as Mach number and pressure. The user may interactively rotate and translate the graphical objects using the mouse. The software source code was written in cross-platform Java, C++, and OpenGL, and runs on Unix, Linux, and Windows. The graphical user interface (GUI) was written using Java Swing. Java also provides multiple synchronized threads. The Java Native Interface (JNI) provides a bridge between the Java code and the C++ code where the PLOT3D files are read, the OpenGL graphics are rendered, and numerical calculations are performed. AirShow is easy to learn and simple to use. The source code is available for free from the NASA Technology Transfer and Partnership Office.

RNA-seq analyses reveal insights into the function of respiratory nitrate reductase of the diazotroph Herbaspirillum seropedicae.

Science.gov (United States)

Bonato, Paloma; Batista, Marcelo B; Camilios-Neto, Doumit; Pankievicz, Vânia C S; Tadra-Sfeir, Michelle Z; Monteiro, Rose Adele; Pedrosa, Fabio O; Souza, Emanuel M; Chubatsu, Leda S; Wassem, Roseli; Rigo, Liu Un

2016-09-01

Herbaspirillum seropedicae is a nitrogen-fixing β-proteobacterium that associates with roots of gramineous plants. In silico analyses revealed that H. seropedicae genome has genes encoding a putative respiratory (NAR) and an assimilatory nitrate reductase (NAS). To date, little is known about nitrate metabolism in H. seropedicae, and, as this bacterium cannot respire nitrate, the function of NAR remains unknown. This study aimed to investigate the function of NAR in H. seropedicae and how it metabolizes nitrate in a low aerated-condition. RNA-seq transcriptional profiling in the presence of nitrate allowed us to pinpoint genes important for nitrate metabolism in H. seropedicae, including nitrate transporters and regulatory proteins. Additionally, both RNA-seq data and physiological characterization of a mutant in the catalytic subunit of NAR (narG mutant) showed that NAR is not required for nitrate assimilation but is required for: (i) production of high levels of nitrite, (ii) production of NO and (iii) dissipation of redox power, which in turn lead to an increase in carbon consumption. In addition, wheat plants showed an increase in shoot dry weight only when inoculated with H. seropedicae wild type, but not with the narG mutant, suggesting that NAR is important to H. seropedicae-wheat interaction. © 2016 Society for Applied Microbiology and John Wiley & Sons Ltd.

Large-Scale No-Show Patterns and Distributions for Clinic Operational Research

Directory of Open Access Journals (Sweden)

Michael L. Davies

2016-02-01

Full Text Available Patient no-shows for scheduled primary care appointments are common. Unused appointment slots reduce patient quality of care, access to services and provider productivity while increasing loss to follow-up and medical costs. This paper describes patterns of no-show variation by patient age, gender, appointment age, and type of appointment request for six individual service lines in the United States Veterans Health Administration (VHA. This retrospective observational descriptive project examined 25,050,479 VHA appointments contained in individual-level records for eight years (FY07-FY14 for 555,183 patients. Multifactor analysis of variance (ANOVA was performed, with no-show rate as the dependent variable, and gender, age group, appointment age, new patient status, and service line as factors. The analyses revealed that males had higher no-show rates than females to age 65, at which point males and females exhibited similar rates. The average no-show rates decreased with age until 75–79, whereupon rates increased. As appointment age increased, males and new patients had increasing no-show rates. Younger patients are especially prone to no-show as appointment age increases. These findings provide novel information to healthcare practitioners and management scientists to more accurately characterize no-show and attendance rates and the impact of certain patient factors. Future general population data could determine whether findings from VHA data generalize to others.

Large-Scale No-Show Patterns and Distributions for Clinic Operational Research.

Science.gov (United States)

Davies, Michael L; Goffman, Rachel M; May, Jerrold H; Monte, Robert J; Rodriguez, Keri L; Tjader, Youxu C; Vargas, Dominic L

2016-02-16

Patient no-shows for scheduled primary care appointments are common. Unused appointment slots reduce patient quality of care, access to services and provider productivity while increasing loss to follow-up and medical costs. This paper describes patterns of no-show variation by patient age, gender, appointment age, and type of appointment request for six individual service lines in the United States Veterans Health Administration (VHA). This retrospective observational descriptive project examined 25,050,479 VHA appointments contained in individual-level records for eight years (FY07-FY14) for 555,183 patients. Multifactor analysis of variance (ANOVA) was performed, with no-show rate as the dependent variable, and gender, age group, appointment age, new patient status, and service line as factors. The analyses revealed that males had higher no-show rates than females to age 65, at which point males and females exhibited similar rates. The average no-show rates decreased with age until 75-79, whereupon rates increased. As appointment age increased, males and new patients had increasing no-show rates. Younger patients are especially prone to no-show as appointment age increases. These findings provide novel information to healthcare practitioners and management scientists to more accurately characterize no-show and attendance rates and the impact of certain patient factors. Future general population data could determine whether findings from VHA data generalize to others.

H-point standard additions method for simultaneous determination of sulfamethoxazole and trimethoprim in pharmaceutical formulations and biological fluids with simultaneous addition of two analytes

Science.gov (United States)

Givianrad, M. H.; Saber-Tehrani, M.; Aberoomand-Azar, P.; Mohagheghian, M.

2011-03-01

The applicability of H-point standard additions method (HPSAM) to the resolving of overlapping spectra corresponding to the sulfamethoxazole and trimethoprim is verified by UV-vis spectrophotometry. The results show that the H-point standard additions method with simultaneous addition of both analytes is suitable for the simultaneous determination of sulfamethoxazole and trimethoprim in aqueous media. The results of applying the H-point standard additions method showed that the two drugs could be determined simultaneously with the concentration ratios of sulfamethoxazole to trimethoprim varying from 1:18 to 16:1 in the mixed samples. Also, the limits of detections were 0.58 and 0.37 μmol L -1 for sulfamethoxazole and trimethoprim, respectively. In addition the means of the calculated RSD (%) were 1.63 and 2.01 for SMX and TMP, respectively in synthetic mixtures. The proposed method has been successfully applied to the simultaneous determination of sulfamethoxazole and trimethoprim in some synthetic, pharmaceutical formulation and biological fluid samples.

Self-Cleaning Photocatalytic Polyurethane Coatings Containing Modified C60 Fullerene Additives

Directory of Open Access Journals (Sweden)

Jeffrey G. Lundin

2014-08-01

Full Text Available Surfaces are often coated with paint for improved aesthetics and protection; however, additional functionalities that impart continuous self-decontaminating and self-cleaning properties would be extremely advantageous. In this report, photochemical additives based on C60 fullerene were incorporated into polyurethane coatings to investigate their coating compatibility and ability to impart chemical decontaminating capability to the coating surface. C60 exhibits unique photophysical properties, including the capability to generate singlet oxygen upon exposure to visible light; however, C60 fullerene exhibits poor solubility in solvents commonly employed in coating applications. A modified C60 containing a hydrophilic moiety was synthesized to improve polyurethane compatibility and facilitate segregation to the polymer–air interface. Bulk properties of the polyurethane films were analyzed to investigate additive–coating compatibility. Coatings containing photoactive additives were subjected to self-decontamination challenges against representative chemical contaminants and the effects of additive loading concentration, light exposure, and time on chemical decontamination are reported. Covalent attachment of an ethylene glycol tail to C60 improved its solubility and dispersion in a hydrophobic polyurethane matrix. Decomposition products resulting from oxidation were observed in addition to a direct correlation between additive loading concentration and decomposition of surface-residing contaminants. The degradation pathways deduced from contaminant challenge byproduct analyses are detailed.

The complete plastome of macaw palm [Acrocomia aculeata (Jacq.) Lodd. ex Mart.] and extensive molecular analyses of the evolution of plastid genes in Arecaceae.

Science.gov (United States)

de Santana Lopes, Amanda; Gomes Pacheco, Túlio; Nimz, Tabea; do Nascimento Vieira, Leila; Guerra, Miguel P; Nodari, Rubens O; de Souza, Emanuel Maltempi; de Oliveira Pedrosa, Fábio; Rogalski, Marcelo

2018-04-01

The plastome of macaw palm was sequenced allowing analyses of evolution and molecular markers. Additionally, we demonstrated that more than half of plastid protein-coding genes in Arecaceae underwent positive selection. Macaw palm is a native species from tropical and subtropical Americas. It shows high production of oil per hectare reaching up to 70% of oil content in fruits and an interesting plasticity to grow in different ecosystems. Its domestication and breeding are still in the beginning, which makes the development of molecular markers essential to assess natural populations and germplasm collections. Therefore, we sequenced and characterized in detail the plastome of macaw palm. A total of 221 SSR loci were identified in the plastome of macaw palm. Additionally, eight polymorphism hotspots were characterized at level of subfamily and tribe. Moreover, several events of gain and loss of RNA editing sites were found within the subfamily Arecoideae. Aiming to uncover evolutionary events in Arecaceae, we also analyzed extensively the evolution of plastid genes. The analyses show that highly divergent genes seem to evolve in a species-specific manner, suggesting that gene degeneration events may be occurring within Arecaceae at the level of genus or species. Unexpectedly, we found that more than half of plastid protein-coding genes are under positive selection, including genes for photosynthesis, gene expression machinery and other essential plastid functions. Furthermore, we performed a phylogenomic analysis using whole plastomes of 40 taxa, representing all subfamilies of Arecaceae, which placed the macaw palm within the tribe Cocoseae. Finally, the data showed here are important for genetic studies in macaw palm and provide new insights into the evolution of plastid genes and environmental adaptation in Arecaceae.

Determination of crack morphology parameters from service failures for leak-rate analyses

Energy Technology Data Exchange (ETDEWEB)

Wilkowski, G.; Ghadiali, N.; Paul, D. [Battelle Memorial Institute, Columbus, OH (United States)] [and others

1997-04-01

In leak-rate analyses described in the literature, the crack morphology parameters are typically not well agreed upon by different investigators. This paper presents results on a review of crack morphology parameters determined from examination of service induced cracks. Service induced cracks were found to have a much more tortuous flow path than laboratory induced cracks due to crack branching associated with the service induced cracks. Several new parameters such as local and global surface roughnesses, as well as local and global number of turns were identified. The effect of each of these parameters are dependent on the crack-opening displacement. Additionally, the crack path is typically assumed to be straight through the pipe thickness, but the service data show that the flow path can be longer due to the crack following a fusion line, and/or the number of turns, where the number of turns in the past were included as a pressure drop term due to the turns, but not the longer flow path length. These parameters were statistically evaluated for fatigue cracks in air, corrosion-fatigue, IGSCC, and thermal fatigue cracks. A refined version of the SQUIRT leak-rate code was developed to account for these variables. Sample calculations are provided in this paper that show how the crack size can vary for a given leak rate and the statistical variation of the crack morphology parameters.

Sintering of magnesia: effect of additives

Indian Academy of Sciences (India)

Effect of different additives, namely Cr2O3, Fe2O3 and TiO2, up to 2 wt% was studied on the sinter- ing and .... mental distribution of the components is shown in figure 7. It shows ... Chiang Y M, Birniand D and Kingery W 1996 Physical ceram-.

(ajst) additive main effects and multiplicative

African Journals Online (AJOL)

2013-08-02

Aug 2, 2013 ... genotypes assessed by biplot analysis showed that the most stable ... biplot is a useful tool for the analysis of multi-environment trial (MET) data. ... multiplicative components, extracting first the additive ... The AMMI analysis of variance of cassava harvest index of the 8 .... wheat mega-environments in Iran.

A retrospective cost-analysis of additional homeopathic treatment in Germany: Long-term economic outcomes

Science.gov (United States)

Ostermann, Julia K.; Witt, Claudia M.; Reinhold, Thomas

2017-01-01

Objectives This study aimed to provide a long-term cost comparison of patients using additional homeopathic treatment (homeopathy group) with patients using usual care (control group) over an observation period of 33 months. Methods Health claims data from a large statutory health insurance company were analysed from both the societal perspective (primary outcome) and from the statutory health insurance perspective (secondary outcome). To compare costs between patient groups, homeopathy and control patients were matched in a 1:1 ratio using propensity scores. Predictor variables for the propensity scores included health care costs and both medical and demographic variables. Health care costs were analysed using an analysis of covariance, adjusted for baseline costs, between groups both across diagnoses and for specific diagnoses over a period of 33 months. Specific diagnoses included depression, migraine, allergic rhinitis, asthma, atopic dermatitis, and headache. Results Data from 21,939 patients in the homeopathy group (67.4% females) and 21,861 patients in the control group (67.2% females) were analysed. Health care costs over the 33 months were 12,414 EUR [95% CI 12,022–12,805] in the homeopathy group and 10,428 EUR [95% CI 10,036–10,820] in the control group (phomeopathy: EUR 6,289 [6,118–6,460]; control: EUR 5,498 [5,326–5,670], phomeopathy: EUR 1,794 [1,770–1,818]; control: EUR 1,438 [1,414–1,462], phomeopathy patients generated higher costs than control patients. Conclusion The analysis showed that even when following-up over 33 months, there were still cost differences between groups, with higher costs in the homeopathy group. PMID:28915242

Schema building profiles among elementary school students in solving problems related to operations of addition to fractions on the basis of mathematic abilities

Science.gov (United States)

Gembong, S.; Suwarsono, S. T.; Prabowo

2018-03-01

Schema in the current study refers to a set of action, process, object and other schemas already possessed to build an individual’s ways of thinking to solve a given problem. The current study aims to investigate the schemas built among elementary school students in solving problems related to operations of addition to fractions. The analyses of the schema building were done qualitatively on the basis of the analytical framework of the APOS theory (Action, Process, Object, and Schema). Findings show that the schemas built on students of high and middle ability indicate the following. In the action stage, students were able to add two fractions by way of drawing a picture or procedural way. In the Stage of process, they could add two and three fractions. In the stage of object, they could explain the steps of adding two fractions and change a fraction into addition of fractions. In the last stage, schema, they could add fractions by relating them to another schema they have possessed i.e. the least common multiple. Those of high and middle mathematic abilities showed that their schema building in solving problems related to operations odd addition to fractions worked in line with the framework of the APOS theory. Those of low mathematic ability, however, showed that their schema on each stage did not work properly.

Influence of the gypsum dehydration temperature and alkali additives on the properties of anhydrite cement

Directory of Open Access Journals (Sweden)

Leskeviciene V.

2010-01-01

Full Text Available While dehydrating gypsum with additives at the temperatures of 800°C and 900°C the influence of alkali additives on both the crystalline structure of anhydrite and properties of anhydrite binder was investigated. The industrial and household wastes including other lowcost materials were used as additives. Having heated them with gypsum the anhydrite with alkali activation properties was obtained. The properties of such substances were evaluated using the methods of chemical, diffractive X-ray scanning and scanning electron microscopy (SEM analyses. Some additives, e.g. 5 % ground glass waste, were found to increase crystal agglomerate formation of anhydrite binder, accelerate the hydration process of anhydrite and double the compressive strength of hydrated samples compared to samples without additives.

Delineation of ground-water contamination using soil-gas analyses near Jackson, Tennessee

Science.gov (United States)

Lee, R.W.

1991-01-01

An investigation of the ground-water resources near Jackson, West Tennessee, was conducted during 1988-89. The study included determination of the occurrence of contaminants in the shallow aquifer using soil-gas analyses in the unsaturated zone. Between 1980 and 1988, an underground fuel-storage tank leaked about 3,000 gallons of unleaded fuel to the water table about 4 feet below land surface. A survey of soil gas using a gas chromatograph equipped with a photoionization detector showed concentrations of volatile organic compounds greater than IO, 000 parts per million near the leak These compounds were detected in an area about 240 feet long and 110 feet wide extending west from the point source. The chromatograms provided two distinct 'fingerprints' of volatile organic compounds. The first revealed the presence of benzene, toluene, andxylenes, which are constituents of unleaded fuel, in addition to other volatile compounds, in soil gas in the area near the leak The second did not reveal any detectable benzene, toluene, or xylenes in the soil-gas samples, but showed the presence of other unidentified volatile organic compounds in soil gas north of the storage tank. The distribution of total concentrations of volatile organic compounds in the unsaturated zone indicated that a second plume about 200 feet long and 90 feet wide was present about 100 feet north of the storage tank The second plume could have been the result of previous activities at this site during the 1950's or earlier. Activities at the site are believed to have included storage of solvents used at the nearby railyard and flushing of tanks containing tar onto a gravel-covered parking area. The delineation of these plumes has shown that soil-gas analyses can be a useful technique for identifying areas of contamination with volatile organic compounds in shallow water-table aquifers and may have broad applications in similar situations where the water table is relatively close to the surface.

Analyses of demand response in Denmark

International Nuclear Information System (INIS)

Moeller Andersen, F.; Grenaa Jensen, S.; Larsen, Helge V.; Meibom, P.; Ravn, H.; Skytte, K.; Togeby, M.

2006-10-01

Due to characteristics of the power system, costs of producing electricity vary considerably over short time intervals. Yet, many consumers do not experience corresponding variations in the price they pay for consuming electricity. The topic of this report is: are consumers willing and able to respond to short-term variations in electricity prices, and if so, what is the social benefit of consumers doing so? Taking Denmark and the Nord Pool market as a case, the report focuses on what is known as short-term consumer flexibility or demand response in the electricity market. With focus on market efficiency, efficient allocation of resources and security of supply, the report describes demand response from a micro-economic perspective and provides empirical observations and case studies. The report aims at evaluating benefits from demand response. However, only elements contributing to an overall value are presented. In addition, the analyses are limited to benefits for society, and costs of obtaining demand response are not considered. (au)

Mixed Approach Retrospective Analyses of Suicide and Suicidal Ideation for Brand Compared with Generic Central Nervous System Drugs.

Science.gov (United States)

Cheng, Ning; Rahman, Md Motiur; Alatawi, Yasser; Qian, Jingjing; Peissig, Peggy L; Berg, Richard L; Page, C David; Hansen, Richard A

2018-04-01

Several different types of drugs acting on the central nervous system (CNS) have previously been associated with an increased risk of suicide and suicidal ideation (broadly referred to as suicide). However, a differential association between brand and generic CNS drugs and suicide has not been reported. This study compares suicide adverse event rates for brand versus generic CNS drugs using multiple sources of data. Selected examples of CNS drugs (sertraline, gabapentin, zolpidem, and methylphenidate) were evaluated via the US FDA Adverse Event Reporting System (FAERS) for a hypothesis-generating study, and then via administrative claims and electronic health record (EHR) data for a more rigorous retrospective cohort study. Disproportionality analyses with reporting odds ratios and 95% confidence intervals (CIs) were used in the FAERS analyses to quantify the association between each drug and reported suicide. For the cohort studies, Cox proportional hazards models were used, controlling for demographic and clinical characteristics as well as the background risk of suicide in the insured population. The FAERS analyses found significantly lower suicide reporting rates for brands compared with generics for all four studied products (Breslow-Day P brand CNS drugs in FAERS and adjusted retrospective cohort analyses remained significant only for sertraline. However, even for sertraline, temporal confounding related to the close proximity of black box warnings and generic availability is possible. Additional analyses in larger data sources with additional drugs are needed.

Forensic applications of scanning electron microscopy/energy dispersive X-ray analyser in Hong Kong.

Science.gov (United States)

Wong, Y S

1982-01-01

Scanning Electron Microscopy - Energy Dispersive X-Ray Analysis (SEM/EDX) has been applied in casework for more than a year in the Forensic Division, Government Laboratory of Hong Kong. The types of samples being analysed are summarised and three cases of scientific interest are described. The first case applies SEM/EDX to characterize microscopic gold particles recovered from clothing of suspects involved in goldsmith robberies. Both elemental and morphological results obtained were used as supporting evidence. The second case describes the three types of beaded ends on fibres found in a single cloth sample. These beaded ends are different in shape and surface features and can be used as an additional parameter in fibre identification. The final case shows the application of vacuum evaporation of graphite on a document sample to reveal the area of paper which has been skillfully mechanically erased. Both the image intensity and the composition of the ink are used to differentiate between original and altered characters on the document.

Significance of Glucose Addition on Chitosan-Glycerophosphate Hydrogel Properties

Directory of Open Access Journals (Sweden)

Dian Susanthy

2016-03-01

Full Text Available Chitosan-glycerophosphate hydrogel can be used as dental scaffold due to its thermosensitivity, gelation performance at body temperature, suitable acidity for body condition, biocompatibility, and ability to provide good environment for cell proliferation and differentiation. Previous study showed that glucose addition to the chitosan solution before steam sterilization improved its hydrogel mechanical strength. However, the effectiveness of glucose addition was still doubted because glucose might undergo Maillard reaction in that particular condition. The aims of this study are to confirm whether the glucose addition can increase the hydrogel mechanical strength and gelation rate effectively and also to compare their performance to be dental scaffold. This research was performed through several steps, namely preparation of chitosan-glycerophosphate solution, addition of glucose, gelation time test, gel mechanical strength measurement, functional group analysis, and physical properties measurements (pH, viscosity, and pore size. The result showed that glucose addition did not improve the hydrogel mechanical strength and gelation rate, neither when it was added before nor after steam sterilization. Glucose addition before steam sterilization seemed to trigger Maillard reaction or browning effect, while glucose addition after steam sterilization increased the amount of free water molecules in the hydrogel. Chitosan and glycerophosphate interact physically, but interaction between chitosan and glucose seems to occur chemically and followed by the formation of free water molecules. Glucose addition decreases the solution viscosity and hydrogel pore size so the hydrogel performance as dental scaffold is lowered.

Altered Brain Activity in Unipolar Depression Revisited: Meta-analyses of Neuroimaging Studies.

Science.gov (United States)

Müller, Veronika I; Cieslik, Edna C; Serbanescu, Ilinca; Laird, Angela R; Fox, Peter T; Eickhoff, Simon B

2017-01-01

During the past 20 years, numerous neuroimaging experiments have investigated aberrant brain activation during cognitive and emotional processing in patients with unipolar depression (UD). The results of those investigations, however, vary considerably; moreover, previous meta-analyses also yielded inconsistent findings. To readdress aberrant brain activation in UD as evidenced by neuroimaging experiments on cognitive and/or emotional processing. Neuroimaging experiments published from January 1, 1997, to October 1, 2015, were identified by a literature search of PubMed, Web of Science, and Google Scholar using different combinations of the terms fMRI (functional magnetic resonance imaging), PET (positron emission tomography), neural, major depression, depression, major depressive disorder, unipolar depression, dysthymia, emotion, emotional, affective, cognitive, task, memory, working memory, inhibition, control, n-back, and Stroop. Neuroimaging experiments (using fMRI or PET) reporting whole-brain results of group comparisons between adults with UD and healthy control individuals as coordinates in a standard anatomic reference space and using an emotional or/and cognitive challenging task were selected. Coordinates reported to show significant activation differences between UD and healthy controls during emotional or cognitive processing were extracted. By using the revised activation likelihood estimation algorithm, different meta-analyses were calculated. Meta-analyses tested for brain regions consistently found to show aberrant brain activation in UD compared with controls. Analyses were calculated across all emotional processing experiments, all cognitive processing experiments, positive emotion processing, negative emotion processing, experiments using emotional face stimuli, experiments with a sex discrimination task, and memory processing. All meta-analyses were calculated across experiments independent of reporting an increase or decrease of activity in

Validation analysis of probabilistic models of dietary exposure to food additives.

Science.gov (United States)

Gilsenan, M B; Thompson, R L; Lambe, J; Gibney, M J

2003-10-01

The validity of a range of simple conceptual models designed specifically for the estimation of food additive intakes using probabilistic analysis was assessed. Modelled intake estimates that fell below traditional conservative point estimates of intake and above 'true' additive intakes (calculated from a reference database at brand level) were considered to be in a valid region. Models were developed for 10 food additives by combining food intake data, the probability of an additive being present in a food group and additive concentration data. Food intake and additive concentration data were entered as raw data or as a lognormal distribution, and the probability of an additive being present was entered based on the per cent brands or the per cent eating occasions within a food group that contained an additive. Since the three model components assumed two possible modes of input, the validity of eight (2(3)) model combinations was assessed. All model inputs were derived from the reference database. An iterative approach was employed in which the validity of individual model components was assessed first, followed by validation of full conceptual models. While the distribution of intake estimates from models fell below conservative intakes, which assume that the additive is present at maximum permitted levels (MPLs) in all foods in which it is permitted, intake estimates were not consistently above 'true' intakes. These analyses indicate the need for more complex models for the estimation of food additive intakes using probabilistic analysis. Such models should incorporate information on market share and/or brand loyalty.

Implementing partnerships in nonreactor facility safety analyses

International Nuclear Information System (INIS)

Courtney, J.C.; Perry, W.H.; Phipps, R.D.

1996-01-01

Faculty and students from LSU have been participating in nuclear safety analyses and radiation protection projects at ANL-W at INEL since 1973. A mutually beneficial relationship has evolved that has resulted in generation of safety-related studies acceptable to Argonne and DOE, NRC, and state regulatory groups. Most of the safety projects have involved the Hot Fuel Examination Facility or the Fuel Conditioning Facility; both are hot cells that receive spent fuel from EBR-II. A table shows some of the major projects at ANL-W that involved LSU students and faculty

Recovery of a wild fish population from whole-lake additions of a synthetic estrogen.

Science.gov (United States)

Blanchfield, Paul J; Kidd, Karen A; Docker, Margaret F; Palace, Vince P; Park, Brad J; Postma, Lianne D

2015-03-03

Despite widespread recognition that municipal wastewaters contain natural and synthetic estrogens, which interfere with development and reproduction of fishes in freshwaters worldwide, there are limited data on the extent to which natural populations of fish can recover from exposure to these compounds. We conducted whole-lake additions of an active component of the birth control pill (17α-ethynylestradiol; EE2) that resulted in the collapse of the fathead minnow (Pimephales promelas) population. Here we quantify physiological, population, and genetic characteristics of this population over the 7 years after EE2 additions stopped to determine if complete recovery was possible. By 3 years post-treatment, whole-body vitellogenin concentrations in male fathead minnow had returned to baseline, and testicular abnormalities were absent. In the spring of the fourth year, adult size-frequency distribution and abundance had returned to pretreatment levels. Microsatellite analyses clearly showed that postrecovery fish were descendants of the original EE2-treated population. Results from this whole-lake experiment demonstrate that fish can recover from EE2 exposure at the biochemical through population levels, although the timelines to do so are long for multigenerational exposures. These results suggest that wastewater treatment facilities that reduce discharges of estrogens and their mimics can improve the health of resident fish populations in their receiving environments.

Innovative Additive for Bitumen Based on Processed Fats

Science.gov (United States)

Babiak, Michał; Kosno, Jacek; Ratajczak, Maria; Zieliński, Krzysztof

2017-10-01

Various additives, admixtures and modifiers are used to improve technical properties and strength characteristics of building materials. Manufacturers of waterproofing materials, concrete, ceramics and bitumen have to use innovative, increasingly complex and costly additives, admixtures or modifiers. As a result, simple and inexpensive substances have been replaced by complex, long chain polymers, multi component resins or plastics. For economic and ecological reasons waste materials are more frequently used as additives, admixtures and modifiers. Nowadays the most commonly used physical modifiers of bitumen belong to the group of polymers - large molecular organic compounds of natural origin or being the result of planned chemical synthesis. Polymers are substances that do not chemically react with bitumen, they act as fillers or create a spatial network within bitumen (the so called physical cross-linking). The development of organic chemistry has allowed the synthesis of a number of substances chemically modifying bitumen. The most promising are heterocyclic organic compounds belonging to the group of imidazolines. The aim of the study presented in this paper was to demonstrate the suitability of processed natural and post-refining fat waste (diamidoamine dehydrate) as bitumen modifier. This paper discusses the impact of adding technical imidazoline on selected bitumen characteristics. Samples of bitumen 160/220, which is most commonly used for the production of waterproofing products, were analysed. For base bitumen and bitumen modified with technical imidazoline the following measurements were taken: measurement of the softening point by Ball and Ring method, determination of the breaking point by Fraass method and needle penetration measurement at 25°C. Later the samples were aged using TFOT laboratory method and the basic characteristics were determined again. The results showed that a small amount of imidazoline improved bitumen thermoplastic parameters at

Cleaning Process Development for Metallic Additively Manufactured Parts

Science.gov (United States)

Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

2014-01-01

Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

Search for new physics in $t\\bar{t}$ final states with additional heavy-flavor jets with the ATLAS detector

CERN Document Server

AUTHOR|(SzGeCERN)702756; Juste Rozas, Aurelio

2016-01-01

This dissertation presents searches in $t\\bar{t}$ final states with additional heavy-flavor jets using $20.3\\ {fb^{-1}}$ of $pp$ collision data at $\\sqrt{s} = 8\\ TeV$, recorded with the ATLAS experiment at the LHC. Exploiting this final state, three analyses are presented that address the instability of the Higgs boson mass from different perspectives. The main challenge for the presented analyses lies in the precise modeling of the background, in particular $t\\bar{t}+b\\bar{b}$. Since no measurements have been performed yet on the $t\\bar{t}$ production with additional heavy-flavor jets, the analyses have to rely on Monte Carlo (MC) simulation for the background. Recent developments in MC simulation have improved the description of the background, and a great effort is invested in porting the state-of-the-art predictions into the analyses. The systematic uncertainties on the modeling of the $t\\bar{t}+b\\bar{b}$ background constitute the main source of sensitivity degradation. In order to reduce the impact of ...

Genoa Boat Show – Good Example of Event Management

Directory of Open Access Journals (Sweden)

Dunja Demirović

2012-07-01

Full Text Available International Boat Show, a business and tourist event, has been held annually in Italian city of Genoa since 1962. The fair is one of the oldest, largest and best known in the field of boating industry worldwide, primarily due to good management of the event and it can serve as case study for domestic fair organizers to improve the quality of their business and services. Since Belgrade is the city of fairs, but compared to Genoa still underdeveloped in terms of trade shows, the following tasks imposed naturally in this study: to determine the relationship of the organizers of Genoa Boat Show in the sector of preparation and fair offer, in the sector of selection and communication with specific target groups (especially visitors, services during the fair and functioning of the city during the fair. During the research the authors have mostly used historical method, comparison, synthesis and the interview method. The results of theoretical research, in addition, may help not only managers of fair shows and of exhibitions, but also to organizers of other events in our country

Analysing the impact of renewable electricity support schemes on power prices: The case of wind electricity in Spain

Energy Technology Data Exchange (ETDEWEB)

Saenz de Miera, Gonzalo [Department of Public Economics, Universidad Autonoma de Madrid, Campus de Cantoblanco, Madrid 28049 (Spain); del Rio Gonzalez, Pablo [Institute for Public Policies, Centro de Ciencias Humanas y Sociales, CSIC, C/Albasanz 26-28, 28037 Madrid (Spain); Vizcaino, Ignacio [Iberdrola, C/Tomas Redondo, 1, Madrid 28033 (Spain)

2008-09-15

It is sometimes argued that renewables are 'expensive'. However, although it is generally true that the private costs of renewable electricity generation are certainly above those of conventional electricity, that statement fails to consider the social benefits provided by electricity from renewable energy sources (RES-E), including environmental and socioeconomic ones. This paper empirically analyses an additional albeit usually neglected benefit: the reduction in the wholesale price of electricity as a result of more RES-E generation being fed into the grid. The case of wind generation in Spain shows that this reduction is greater than the increase in the costs for the consumers arising from the RES-E support scheme (the feed-in tariffs), which are charged to the final consumer. Therefore, a net reduction in the retail electricity price results, which is positive from a consumer point of view. This provides an additional argument for RES-E support and contradicts one of the usual arguments against RES-E deployment: the excessive burden on the consumer. (author)

Analysis and discussion on reports of additional safety assessment of nuclear installations with respect to the Fukushima accident

International Nuclear Information System (INIS)

Sene, Monique; Sene, Raymond

2011-11-01

This document proposes an analysis of the reports made by the different operators of nuclear installations within the frame of a safety audit of the French nuclear installations with respect to the Fukushima accident. Operators (mainly AREVA, the CEA and EDF) were asked to perform additional safety assessments. In a first part, the conclusions of EDF reports are analysed regarding the seismic risk, the flooding risk, the situation of some specific sites (Fessenheim, Tricastin), other phenomena (rains, winds), loss of electricity supplies and of cooling systems, severe accidents, hydrogen issue, chemical hazards, subcontractors, crisis management. Conclusions of AREVA reports are analysed for the different sites (Tricastin, La Hague, MELOX factory, Romans factory). Conclusions of CEA reports are analysed for the different concerned installations (ATPu, Masurca, Osiris, Phenix, Jules Horowitz reactor). A second part proposes a global analysis of EDF's additional safety assessment reports regarding earthquake, flooding, other extreme natural phenomena, loss of electricity supplies and cooling system, subcontracting conditions, crisis management, and radiation protection organisation. AREVA's and CEA's reports are then analysed in terms of report structure and content, and for the different concerned sites

Magnetic resonance spectroscopy (MRS) of vertebral column – an additional tool for evaluation of aggressiveness of vertebral haemangioma like lesion

International Nuclear Information System (INIS)

Jeromel, Miran; Podobnik, Janez

2014-01-01

Most vertebral haemangioma are asymptomatic and discovered incidentally. Sometimes the symptomatic lesions present with radiological signs of aggressiveness and their appearance resemble other aggressive lesions (e.g. solitary plasmacytoma). We present a patient with large symptomatic aggressive haemangioma like lesion in 12 th thoracic vertebra in which a magnetic resonance spectroscopy (MRS) was used to analyse fat content within the lesion. The lesion in affected vertebrae showed low fat content with 33% of fat fraction (%FF). The fat content in non-affected (1 st lumbar) vertebra was as expected for patient’s age (68%). Based on MRS data, the lesion was characterized as an aggressive haemangioma. The diagnosis was confirmed with biopsy, performed during the treatment – percutaneous vertebroplasty. The presented case shows that MRS can be used as an additional tool for evaluation of aggressiveness of vertebral haemangioma like lesions

Proceedings of the 2nd CSNI Specialist Meeting on Simulators and Plant Analysers

International Nuclear Information System (INIS)

Tiihonen, O.

1999-01-01

The safe utilisation of nuclear power plants requires the availability of different computerised tools for analysing the plant behaviour and training the plant personnel. These can be grouped into three categories: accident analysis codes, plant analysers and training simulators. The safety analysis of nuclear power plants has traditionally been limited to the worst accident cases expected for the specific plant design. Many accident analysis codes have been developed for different plant types. The scope of the analyses has continuously expanded. The plant analysers are now emerging tools intended for extensive analysis of the plant behaviour using a best estimate model for the whole plant including the reactor and full thermodynamic process, both combined with automation and electrical systems. The comprehensive model is also supported by good visualisation tools. Training simulators with real time plant model are tools for training the plant operators to run the plant. Modern training simulators have also features supporting visualisation of the important phenomena occurring in the plant during transients. The 2nd CSNI Specialist Meeting on Simulators and Plant Analysers in Espoo attracted some 90 participants from 17 countries. A total of 49 invited papers were presented in the meeting in addition to 7 simulator system demonstrations. Ample time was reserved for the presentations and informal discussions during the four meeting days. (orig.)

Additional reactor protection system of RBMK-1500

International Nuclear Information System (INIS)

1999-01-01

Analysis of anticipated transients without scram of RBMK-1500 reactor showed that additional reactor protection system is required. Data of accident analysis in the case of loose of external electric power and loose of vacuum in condensers of turbines are provided

Practical applications of probabilistic structural reliability analyses to primary pressure systems of nuclear power plants

International Nuclear Information System (INIS)

Witt, F.J.

1980-01-01

Primary pressure systems of nuclear power plants are built to exacting codes and standards with provisions for inservice inspection and repair if necessary. Analyses and experiments have demonstrated by deterministic means that very large margins exist on safety impacting failures under normal operating and upset conditions. Probabilistic structural reliability analyses provide additional support that failures of significance are very, very remote. They may range in degree of sophistication from very simple calculations to very complex computer analyses involving highly developed mathematical techniques. The end result however should be consistent with the desired usage. In this paper a probabilistic structural reliability analysis is performed as a supplement to in-depth deterministic evaluations with the primary objective to demonstrate an acceptably low probability of failure for the conditions considered. (author)

Sintering of manganese ore in natura with different additions on activated carbon

International Nuclear Information System (INIS)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F.

2016-01-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Sintering of manganese ore in natura with different additions on activated carbon

Energy Technology Data Exchange (ETDEWEB)

Lima, M.M.F.; Mapa, T.F.M.; Lima, R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

2016-07-01

Full text: The shortage of high grade manganese ore and the importance of economically viable processes suggest a necessity of the recovery of ore residues. So, this work presents a route to obtain by-products of economic interest from manganese ore residues in bench scale. The objective was the sintering of manganese ore in natura using a particle size below 0,037μm with different additions of activated carbon. For this, the fine residues were calcined at 800°C during 60 minutes, homogenized in an agate mortar with 12% humidity and additions of 9 and 12% of activated carbon. After homogenization, the sintering process was carried out at 1145°C and 1155°C during 5, 15 and 30 minutes at natural air. The products sintered were characterized by bulk density, BET surface area, OM, SEM / EDS and diffraction X-rays. During the calcination of the ore, the mass loss was (15.16 ± 0.02)% due to the elimination of volatiles and water. The surface area of the ore was reduced due to the diffusion process that occurred during sintering. While, the bulk density values had little variation, around (3.51 ± 0.06)g/cm³. The analyses of micro-regions EDS showed that the matrix is a silicate with a high Mn content. It was identified yet, other silicates with different proportions of Si, Al, Ti, Na, Mn, Mg and Ca. (author)

Influence of additives on the stability of the phases of alumina

International Nuclear Information System (INIS)

Rosario, D.C.C.; Gouvea, D.

2011-01-01

Problems with the stability of gamma alumina in catalytic reactions have been solved with the inclusion of additives during the synthesis of alumina. These additives stabilize the temperature of phase transition allowing the use of metastable alumina at high temperatures, but the mechanisms of action of additives are not well defined. It is known that each family of additive or additives behaves in different ways for this stabilization. This work aimed to study the performance of MgO and ZrO 2 , respectively at different concentrations in alumina synthesized via Pechini. The samples were analyzed by DSC, X-ray diffraction, measurement of specific surface area by BET analysis, and infrared analysis. The results showed an increase in transition temperature for both additives, and a different changes for specific surface area, showing that MgO and ZrO 2 work on improving the stability but with distinct mechanisms. (author)

Intrinsic dependence of the magnetic properties of CoFe{sub 2}O{sub 4} nanoparticles prepared via chemical methods with addition of chelating agents

Energy Technology Data Exchange (ETDEWEB)

Mendonça, E.C. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Tenório, Mayara A. [Departamento de Física, Campus Prof. Alberto Carvalho, UFS, 49500-000 Itabaiana, SE (Brazil); Mecena, S.G.; Zucolotto, B.; Silva, L.S. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); Jesus, C.B.R. [Instituto de Física Gleb Wataghin, UNICAMP, C. P. 6165, 13083-970 Campinas, SP (Brazil); Meneses, C.T. [Núcleo de Pós-Graduação em Física, Campus Prof. José Aluísio de Campos, UFS, 49100-000 São Cristóvão, SE (Brazil); and others

2015-12-01

In this work, the effect of addition of different chelating agents on the magnetic properties of cobalt ferrite nanoparticles produced by the combining of both co-precipitation and hydrothermal methods is reported. The Rietveld analyses of X-ray diffraction patterns reveal that our samples are single phase (space group: Fd-3m) with small average sizes. The weight losses observed in the thermogravimetric measurements together with the M×H curves show that the organic contamination coming from chelating agent decomposition can give rise to misinterpretation of the magnetization measurements. Besides, analyses of the zero-field-cooled (ZFC) and field-cooled (FC) magnetization measurements and the M×H curves measured at room temperature allows us to state that both the average blocking temperature and particles size distribution are sensitive to the kind of chelating agent. - Highlights: Superparamagnetism. Chelating agents. Organic contamination.

Methodical treatment of dependent failures in risk analyses

International Nuclear Information System (INIS)

Hennings, W.; Mertens, J.

1987-06-01

In this report the state-of-the-art regarding dependent failures is compiled and commented on. Among others the following recommendations are infered: The term 'common mode failures' should be restricted to failures of redundant, similar components; the generic term is 'dependent failures' with the subsets 'causal failures' and 'common cause failures'. In risk studies, dependent failures should be covered as far as possible by 'explicit methods'. Nevertheless an uncovered rest remains, which should be accounted for by sensitivity analyses using 'implicit methods'. For this the homogeneous Marshall-Olkin model is recommended. Because the available reports on operating experiences only record 'common mode failures' systematically, it is recommended to additionally apply other methods, e.g. carry out a 'precursor study'. (orig.) [de

A systematic meta-review of evaluations of youth violence prevention programs: Common and divergent findings from 25 years of meta-analyses and systematic reviews☆

Science.gov (United States)

Matjasko, Jennifer L.; Vivolo-Kantor, Alana M.; Massetti, Greta M.; Holland, Kristin M.; Holt, Melissa K.; Cruz, Jason Dela

2018-01-01

Violence among youth is a pervasive public health problem. In order to make progress in reducing the burden of injury and mortality that result from youth violence, it is imperative to identify evidence-based programs and strategies that have a significant impact on violence. There have been many rigorous evaluations of youth violence prevention programs. However, the literature is large, and it is difficult to draw conclusions about what works across evaluations from different disciplines, contexts, and types of programs. The current study reviews the meta-analyses and systematic reviews published prior to 2009 that synthesize evaluations of youth violence prevention programs. This meta-review reports the findings from 37 meta-analyses and 15 systematic reviews; the included reviews were coded on measures of the social ecology, prevention approach, program type, and study design. A majority of the meta-analyses and systematic reviews were found to demonstrate moderate program effects. Meta-analyses yielded marginally smaller effect sizes compared to systematic reviews, and those that included programs targeting family factors showed marginally larger effects than those that did not. In addition, there are a wide range of individual/family, program, and study moderators of program effect sizes. Implications of these findings and suggestions for future research are discussed. PMID:29503594

Additivity for parametrized topological Euler characteristic and Reidemeister torsion

OpenAIRE

Badzioch, Bernard; Dorabiala, Wojciech

2005-01-01

Dwyer, Weiss, and Williams have recently defined the notions of parametrized topological Euler characteristic and parametrized topological Reidemeister torsion which are invariants of bundles of compact topological manifolds. We show that these invariants satisfy additivity formulas paralleling the additive properties of the classical Euler characteristic and Reidemeister torsion of finite CW-complexes.

Laser Beam Focus Analyser

DEFF Research Database (Denmark)

Nielsen, Peter Carøe; Hansen, Hans Nørgaard; Olsen, Flemming Ove

2007-01-01

the obtainable features in direct laser machining as well as heat affected zones in welding processes. This paper describes the development of a measuring unit capable of analysing beam shape and diameter of lasers to be used in manufacturing processes. The analyser is based on the principle of a rotating......The quantitative and qualitative description of laser beam characteristics is important for process implementation and optimisation. In particular, a need for quantitative characterisation of beam diameter was identified when using fibre lasers for micro manufacturing. Here the beam diameter limits...... mechanical wire being swept through the laser beam at varying Z-heights. The reflected signal is analysed and the resulting beam profile determined. The development comprised the design of a flexible fixture capable of providing both rotation and Z-axis movement, control software including data capture...

Prediction of Seismic Slope Displacements by Dynamic Stick-Slip Analyses

International Nuclear Information System (INIS)

Ausilio, Ernesto; Costanzo, Antonio; Silvestri, Francesco; Tropeano, Giuseppe

2008-01-01

A good-working balance between simplicity and reliability in assessing seismic slope stability is represented by displacement-based methods, in which the effects of deformability and ductility can be either decoupled or coupled in the dynamic analyses. In this paper, a 1D lumped mass ''stick-slip'' model is developed, accounting for soil heterogeneity and non-linear behaviour, with a base sliding mechanism at a potential rupture surface. The results of the preliminary calibration show a good agreement with frequency-domain site response analysis in no-slip conditions. The comparison with rigid sliding block analyses and with the decoupled approach proves that the stick-slip procedure can result increasingly unconservative for soft soils and deep sliding depths

Lagrangian Coherent Structure Analysis of Terminal Winds: Three-Dimensionality, Intramodel Variations, and Flight Analyses

Directory of Open Access Journals (Sweden)

Brent Knutson

2015-01-01

Full Text Available We present a study of three-dimensional Lagrangian coherent structures (LCS near the Hong Kong International Airport and relate to previous developments of two-dimensional (2D LCS analyses. The LCS are contrasted among three independent models and against 2D coherent Doppler light detection and ranging (LIDAR data. Addition of the velocity information perpendicular to the LIDAR scanning cone helps solidify flow structures inferred from previous studies; contrast among models reveals the intramodel variability; and comparison with flight data evaluates the performance among models in terms of Lagrangian analyses. We find that, while the three models and the LIDAR do recover similar features of the windshear experienced by a landing aircraft (along the landing trajectory, their Lagrangian signatures over the entire domain are quite different—a portion of each numerical model captures certain features resembling those LCS extracted from independent 2D LIDAR analyses based on observations.

Ancient bacteria show evidence of DNA repair

DEFF Research Database (Denmark)

Johnson, Sarah Stewart; Hebsgaard, Martin B; Christensen, Torben R

2007-01-01

-term survival of bacteria sealed in frozen conditions for up to one million years. Our results show evidence of bacterial survival in samples up to half a million years in age, making this the oldest independently authenticated DNA to date obtained from viable cells. Additionally, we find strong evidence...... geological timescales. There has been no direct evidence in ancient microbes for the most likely mechanism, active DNA repair, or for the metabolic activity necessary to sustain it. In this paper, we couple PCR and enzymatic treatment of DNA with direct respiration measurements to investigate long...... that this long-term survival is closely tied to cellular metabolic activity and DNA repair that over time proves to be superior to dormancy as a mechanism in sustaining bacteria viability....

A single-nucleotide polymorphism of human neuropeptide s gene originated from Europe shows decreased bioactivity.

Directory of Open Access Journals (Sweden)

Cheng Deng

Full Text Available Using accumulating SNP (Single-Nucleotide Polymorphism data, we performed a genome-wide search for polypeptide hormone ligands showing changes in the mature regions to elucidate genotype/phenotype diversity among various human populations. Neuropeptide S (NPS, a brain peptide hormone highly conserved in vertebrates, has diverse physiological effects on anxiety, fear, hyperactivity, food intake, and sleeping time through its cognate receptor-NPSR. Here, we report a SNP rs4751440 (L(6-NPS causing non-synonymous substitution on the 6(th position (V to L of the NPS mature peptide region. L(6-NPS has a higher allele frequency in Europeans than other populations and probably originated from European ancestors ~25,000 yrs ago based on haplotype analysis and Approximate Bayesian Computation. Functional analyses indicate that L(6-NPS exhibits a significant lower bioactivity than the wild type NPS, with ~20-fold higher EC50 values in the stimulation of NPSR. Additional evolutionary and mutagenesis studies further demonstrate the importance of the valine residue in the 6(th position for NPS functions. Given the known physiological roles of NPS receptor in inflammatory bowel diseases, asthma pathogenesis, macrophage immune responses, and brain functions, our study provides the basis to elucidate NPS evolution and signaling diversity among human populations.

Finite element analyses for seismic shear wall international standard problem

International Nuclear Information System (INIS)

Park, Y.J.; Hofmayer, C.H.

1998-04-01

Two identical reinforced concrete (RC) shear walls, which consist of web, flanges and massive top and bottom slabs, were tested up to ultimate failure under earthquake motions at the Nuclear Power Engineering Corporation's (NUPEC) Tadotsu Engineering Laboratory, Japan. NUPEC provided the dynamic test results to the OECD (Organization for Economic Cooperation and Development), Nuclear Energy Agency (NEA) for use as an International Standard Problem (ISP). The shear walls were intended to be part of a typical reactor building. One of the major objectives of the Seismic Shear Wall ISP (SSWISP) was to evaluate various seismic analysis methods for concrete structures used for design and seismic margin assessment. It also offered a unique opportunity to assess the state-of-the-art in nonlinear dynamic analysis of reinforced concrete shear wall structures under severe earthquake loadings. As a participant of the SSWISP workshops, Brookhaven National Laboratory (BNL) performed finite element analyses under the sponsorship of the U.S. Nuclear Regulatory Commission (USNRC). Three types of analysis were performed, i.e., monotonic static (push-over), cyclic static and dynamic analyses. Additional monotonic static analyses were performed by two consultants, F. Vecchio of the University of Toronto (UT) and F. Filippou of the University of California at Berkeley (UCB). The analysis results by BNL and the consultants were presented during the second workshop in Yokohama, Japan in 1996. A total of 55 analyses were presented during the workshop by 30 participants from 11 different countries. The major findings on the presented analysis methods, as well as engineering insights regarding the applicability and reliability of the FEM codes are described in detail in this report. 16 refs., 60 figs., 16 tabs

Genomic Model with Correlation Between Additive and Dominance Effects.

Science.gov (United States)

Xiang, Tao; Christensen, Ole Fredslund; Vitezica, Zulma Gladis; Legarra, Andres

2018-05-09

Dominance genetic effects are rarely included in pedigree-based genetic evaluation. With the availability of single nucleotide polymorphism markers and the development of genomic evaluation, estimates of dominance genetic effects have become feasible using genomic best linear unbiased prediction (GBLUP). Usually, studies involving additive and dominance genetic effects ignore possible relationships between them. It has been often suggested that the magnitude of functional additive and dominance effects at the quantitative trait loci are related, but there is no existing GBLUP-like approach accounting for such correlation. Wellmann and Bennewitz showed two ways of considering directional relationships between additive and dominance effects, which they estimated in a Bayesian framework. However, these relationships cannot be fitted at the level of individuals instead of loci in a mixed model and are not compatible with standard animal or plant breeding software. This comes from a fundamental ambiguity in assigning the reference allele at a given locus. We show that, if there has been selection, assigning the most frequent as the reference allele orients the correlation between functional additive and dominance effects. As a consequence, the most frequent reference allele is expected to have a positive value. We also demonstrate that selection creates negative covariance between genotypic additive and dominance genetic values. For parameter estimation, it is possible to use a combined additive and dominance relationship matrix computed from marker genotypes, and to use standard restricted maximum likelihood (REML) algorithms based on an equivalent model. Through a simulation study, we show that such correlations can easily be estimated by mixed model software and accuracy of prediction for genetic values is slightly improved if such correlations are used in GBLUP. However, a model assuming uncorrelated effects and fitting orthogonal breeding values and dominant

Microstructure and mechanical properties of molybdenum silicides with Al additions

International Nuclear Information System (INIS)

Rosales, I.; Bahena, D.; Colin, J.

2007-01-01

Several molybdenum silicides alloys with different aluminum additions were produced by the arc-cast method. Microstructure observed in the alloys presented a variation of the precipitated second phase respect to the aluminum content. Evaluation of the compressive behavior at high temperature of the alloys shows an important improvement in its ductility, approximately of 20%. Fracture toughness was increased proportionally with Al content. In addition at room temperature the alloys show a better mechanical behavior in comparison with the sample unalloyed. In general, Al additions result to be a good alternative to improve the resistance of these intermetallic alloys. The results are interpreted on the base of the analysis of second phase strengthening

Genetic and epigenetic variations induced by wheat-rye 2R and 5R monosomic addition lines.

Science.gov (United States)

Fu, Shulan; Sun, Chuanfei; Yang, Manyu; Fei, Yunyan; Tan, Feiqun; Yan, Benju; Ren, Zhenglong; Tang, Zongxiang

2013-01-01

Monosomic alien addition lines (MAALs) can easily induce structural variation of chromosomes and have been used in crop breeding; however, it is unclear whether MAALs will induce drastic genetic and epigenetic alterations. In the present study, wheat-rye 2R and 5R MAALs together with their selfed progeny and parental common wheat were investigated through amplified fragment length polymorphism (AFLP) and methylation-sensitive amplification polymorphism (MSAP) analyses. The MAALs in different generations displayed different genetic variations. Some progeny that only contained 42 wheat chromosomes showed great genetic/epigenetic alterations. Cryptic rye chromatin has introgressed into the wheat genome. However, one of the progeny that contained cryptic rye chromatin did not display outstanding genetic/epigenetic variation. 78 and 49 sequences were cloned from changed AFLP and MSAP bands, respectively. Blastn search indicated that almost half of them showed no significant similarity to known sequences. Retrotransposons were mainly involved in genetic and epigenetic variations. Genetic variations basically affected Gypsy-like retrotransposons, whereas epigenetic alterations affected Copia-like and Gypsy-like retrotransposons equally. Genetic and epigenetic variations seldom affected low-copy coding DNA sequences. The results in the present study provided direct evidence to illustrate that monosomic wheat-rye addition lines could induce different and drastic genetic/epigenetic variations and these variations might not be caused by introgression of rye chromatins into wheat. Therefore, MAALs may be directly used as an effective means to broaden the genetic diversity of common wheat.

The optimisation of analyser geometry for a near back-scattering spectrometer. IRIS on the ISIS pulsed source

International Nuclear Information System (INIS)

Telling, M.T.F.; Campbell, S.I.

1999-01-01

This report describes the upgrade of the pyrolytic graphite (PG) analyser bank on the IRIS high-resolution inelastic spectrometer at ISIS from 1350 graphite pieces (6 rows by 225 columns) to 4212 crystal pieces (18 rows by 234 columns). The analyser array will achieve a three-fold increase in area and in addition the graphite crystals will be cooled close to liquid helium temperature to reduce thermal diffuse scattering, thereby further improving the sensitivity of the spectrometer. For an instrument such as IRIS, with its analyser out of exact back-scattering geometry, optical aberration and variation in the time-of-flight of the analysed neutrons is introduced as one moves out from the horizontal scattering plane. To minimise such effects, the profile of the analyser array has been redesigned. The concept behind the design of the new analyser bank and the factors that effect the overall resolution of the instrument are discussed. Results of Monte Carlo simulations of the expected resolution and intensity of the complete instrument are presented and compared to the current instrument performance. (author)

Food resources of stream macroinvertebrates determined by natural-abundance stable C and N isotopes and a 15N tracer addition

Science.gov (United States)

Patrick J. Mulholland; Jennifer L. Tank; Diane M. Sanzone; Wilfrid M. Wollheim; Bruce J. Peterson; Jackson R. Webster; Judy L. Meyer

2000-01-01

Trophic relationships were examined using natural-abundance 13C and 15N analyses and a 15N-tracer addition experiment in Walker Branch, a 1st-order forested stream in eastern Tennessee. In the 15N-tracer addition experiment, we added 15NH4...

Hydrogen Analyses in the EPR

International Nuclear Information System (INIS)

Worapittayaporn, S.; Eyink, J.; Movahed, M.

2008-01-01

In severe accidents with core melting large amounts of hydrogen may be released into the containment. The EPR provides a combustible gas control system to prevent hydrogen combustion modes with the potential to challenge the containment integrity due to excessive pressure and temperature loads. This paper outlines the approach for the verification of the effectiveness and efficiency of this system. Specifically, the justification is a multi-step approach. It involves the deployment of integral codes, lumped parameter containment codes and CFD codes and the use of the sigma criterion, which provides the link to the broad experimental data base for flame acceleration (FA) and deflagration to detonation transition (DDT). The procedure is illustrated with an example. The performed analyses show that hydrogen combustion at any time does not lead to pressure or temperature loads that threaten the containment integrity of the EPR. (authors)

Strategies of Pre-Service Primary School Teachers for Solving Addition Problems with Negative Numbers

Science.gov (United States)

Almeida, Rut; Bruno, Alicia

2014-01-01

This paper analyses the strategies used by pre-service primary school teachers for solving simple addition problems involving negative numbers. The findings reveal six different strategies that depend on the difficulty of the problem and, in particular, on the unknown quantity. We note that students use negative numbers in those problems they find…

Thermal analyses. Information on the expected baking process; Thermische analyses. Informatie over een te verwachten bakgedrag

Energy Technology Data Exchange (ETDEWEB)

Van Wijck, H. [Stichting Technisch Centrum voor de Keramische Industrie TCKI, Velp (Netherlands)

2009-09-01

The design process and the drying process for architectural ceramics and pottery partly determine the characteristics of the final product, but the largest changes occur during the baking process. An overview is provided of the different thermal analyses and how the information from these analyses can predict the process in practice. (mk) [Dutch] Het vormgevingsproces en het droogproces voor bouwkeramische producten en aardewerk bepalen voor een deel de eigenschappen van de eindproducten, maar de grootste veranderingen treden op bij het bakproces. Een overzicht wordt gegeven van de verschillende thermische analyses en hoe de informatie uit deze analyses het in de praktijk te verwachten gedrag kan voorspellen.

Additional EIPC Study Analysis. Final Report

Energy Technology Data Exchange (ETDEWEB)

Hadley, Stanton W [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gotham, Douglas J. [Purdue Univ., West Lafayette, IN (United States); Luciani, Ralph L. [Navigant Consultant Inc., Suwanee, GA (United States)

2014-12-01

Between 2010 and 2012 the Eastern Interconnection Planning Collaborative (EIPC) conducted a major long-term resource and transmission study of the Eastern Interconnection (EI). With guidance from a Stakeholder Steering Committee (SSC) that included representatives from the Eastern Interconnection States Planning Council (EISPC) among others, the project was conducted in two phases. Phase 1 involved a long-term capacity expansion analysis that involved creation of eight major futures plus 72 sensitivities. Three scenarios were selected for more extensive transmission- focused evaluation in Phase 2. Five power flow analyses, nine production cost model runs (including six sensitivities), and three capital cost estimations were developed during this second phase. The results from Phase 1 and 2 provided a wealth of data that could be examined further to address energy-related questions. A list of 14 topics was developed for further analysis. This paper brings together the earlier interim reports of the first 13 topics plus one additional topic into a single final report.

A web-based endpoint adjudication system for interim analyses in clinical trials.

Science.gov (United States)

Nolen, Tracy L; Dimmick, Bill F; Ostrosky-Zeichner, Luis; Kendrick, Amy S; Sable, Carole; Ngai, Angela; Wallace, Dennis

2009-02-01

A data monitoring committee (DMC) is often employed to assess trial progress and review safety data and efficacy endpoints throughout a trail. Interim analyses performed for the DMC should use data that are as complete and verified as possible. Such analyses are complicated when data verification involves subjective study endpoints or requires clinical expertise to determine each subject's status with respect to the study endpoint. Therefore, procedures are needed to obtain adjudicated data for interim analyses in an efficient manner. In the past, methods for handling such data included using locally reported results as surrogate endpoints, adjusting analysis methods for unadjudicated data, or simply performing the adjudication as rapidly as possible. These methods all have inadequacies that make their sole usage suboptimal. For a study of prophylaxis for invasive candidiasis, adjudication of both study eligibility criteria and clinical endpoints prior to two interim analyses was required. Because the study was expected to enroll at a moderate rate and the sponsor required adjudicated endpoints to be used for interim analyses, an efficient process for adjudication was required. We created a web-based endpoint adjudication system (WebEAS) that allows for expedited review by the endpoint adjudication committee (EAC). This system automatically identifies when a subject's data are complete, creates a subject profile from the study data, and assigns EAC reviewers. The reviewers use the WebEAS to review the subject profile and submit their completed review form. The WebEAS then compares the reviews, assigns an additional review as a tiebreaker if needed, and stores the adjudicated data. The study for which this system was originally built was administratively closed after 10 months with only 38 subjects enrolled. The adjudication process was finalized and the WebEAS system activated prior to study closure. Some website accessibility issues presented initially. However

Distinguishing Nonpareil marketing group almond cultivars through multivariate analyses.

Science.gov (United States)

Ledbetter, Craig A; Sisterson, Mark S

2013-09-01

More than 80% of the world's almonds are grown in California with several dozen almond cultivars available commercially. To facilitate promotion and sale, almond cultivars are categorized into marketing groups based on kernel shape and appearance. Several marketing groups are recognized, with the Nonpareil Marketing Group (NMG) demanding the highest prices. Placement of cultivars into the NMG is historical and no objective standards exist for deciding whether newly developed cultivars belong in the NMG. Principal component analyses (PCA) were used to identify nut and kernel characteristics best separating the 4 NMG cultivars (Nonpareil, Jeffries, Kapareil, and Milow) from a representative of the California Marketing Group (cultivar Carmel) and the Mission Marketing Group (cultivar Padre). In addition, discriminant analyses were used to determine cultivar misclassification rates between and within the marketing groups. All 19 evaluated carpological characters differed significantly among the 6 cultivars and during 2 harvest seasons. A clear distinction of NMG cultivars from representatives of the California and Mission Marketing Groups was evident from a PCA involving the 6 cultivars. Further, NMG kernels were successfully discriminated from kernels representing the California and Mission Marketing Groups with overall kernel misclassification of only 2% using 16 of the 19 evaluated characters. Pellicle luminosity was the most discriminating character, regardless of the character set used in analyses. Results provide an objective classification of NMG almond kernels, clearly distinguishing them from kernels of cultivars representing the California and Mission Marketing Groups. Journal of Food Science © 2013 Institute of Food Technologists® No claim to original US government works.

Interfacial behavior of common food contact polymer additives.

Science.gov (United States)

Heiserman, W M; Can, S Z; Walker, R A; Begley, T H; Limm, W

2007-07-15

Irganox 1076 (IN1076) and Irganox 1010 (IN1010), phenol containing species often used as antioxidant additives in food packaging polymers have both hydrophilic and hydrophobic functional groups. Consequently these additives are likely to absorb to surfaces where their free energy is minimized. Experiments described in this work examine the two-dimensional phase behavior and vibrational structure of IN1076 and IN1010 films adsorbed to the air/water interface. Surface pressure isotherms show that repeated compression of these films leads to continued irreversible loss of molecules and that on a per molecule basis, this loss is more pronounced for IN1076 than for IN1010. Differences in the surface properties of these two antioxidant additives are interpreted based on differences in molecular structure. Surface specific vibrational measurements of these organic films show very little conformational order, implying that even when closely packed, both antioxidant species have little affinity for forming highly organized domains. These findings have important ramifications for mechanisms that reduce antioxidant activity in polymers as well as descriptions of antioxidant blooming on polymer surfaces.

Halogenation of Hydraulic Fracturing Additives in the Shale Well Parameter Space

Science.gov (United States)

Sumner, A. J.; Plata, D.

2017-12-01

Horizontal Drilling and Hydraulic fracturing (HDHF) involves the deep-well injection of a `fracking fluid' composed of diverse and numerous chemical additives designed to facilitate the release and collection of natural gas from shale plays. The potential impacts of HDHF operations on water resources and ecosystems are numerous, and analyses of flowback samples revealed organic compounds from both geogenic and anthropogenic sources. Furthermore, halogenated chemicals were also detected, and these compounds are rarely disclosed, suggesting the in situ halogenation of reactive additives. To test this transformation hypothesis, we designed and operated a novel high pressure and temperature reactor system to simulate the shale well parameter space and investigate the chemical reactivity of twelve commonly disclosed and functionally diverse HDHF additives. Early results revealed an unanticipated halogenation pathway of α-β unsaturated aldehyde, Cinnamaldehyde, in the presence of oxidant and concentrated brine. Ongoing experiments over a range of parameters informed a proposed mechanism, demonstrating the role of various shale-well specific parameters in enabling the demonstrated halogenation pathway. Ultimately, these results will inform a host of potentially unintended interactions of HDHF additives during the extreme conditions down-bore of a shale well during HDHF activities.

Investigation of additives for preventing ash fouling and sintering during barley straw combustion

International Nuclear Information System (INIS)

Wang, Liang; Skreiberg, Øyvind; Becidan, Michael

2014-01-01

Formation of potassium chloride reduces ash sintering temperature and causes fouling deposits in biomass combustion applications. In the present work, the capacity of two mineral additives zeolite 24A and kaolin to capture KCl were investigated. A series of thermogravimetric experiments were carried out to measure fractions of KCl retained in the two additives as function of reaction temperature and heating time. The residues from additive-KCl mixtures after heating treatment were analyzed by X-ray diffractometry (XRD). When heated at 900 °C for 1 h, the overall KCl capturing efficiencies of the two additives were 60% and 45% for zeolite 24A and kaolin respectively, which slightly decreased to 50% and 43% as the heating time increased to 12 h. At 1000 °C, the fractions of KCl captured by zeolite 24A and kaolin significantly decreased from 50% and 40% to 26% and 17%, as the KCl-additive mixtures were heated for 1 and 12 h, respectively. The decrease in of the overall KCl capturing efficiencies is mainly attributed to reduction of surface areas and chemically active compounds of the two additives with increasing temperature and heating time. The XRD analysis results showed that both zeolite 24A and kaolin can react with KCl to form different potassium aluminium silicates. It indicates that chemical reactions play an important role in the overall capturing process. The effects of zeolite 24A and kaolin on sintering behaviors of the barley straw ash were also investigated. The residues from sintering tests were analyzed by a combination of X-Ray diffractometry (XRD) and scanning electron microscopy equipped with energy dispersive X-Ray analysis (SEM-EDX). The barley straw ash melted intensively at elevated temperatures. Together with XRD analysis, the SEM-EDX analysis results revealed that severe melting of the barley straw ash was due to formation and fusion of low temperature melting potassium silicates. Addition of kaolin and zeolite 24A significantly

A review of multivariate analyses in imaging genetics

Directory of Open Access Journals (Sweden)

Jingyu eLiu

2014-03-01

Full Text Available Recent advances in neuroimaging technology and molecular genetics provide the unique opportunity to investigate genetic influence on the variation of brain attributes. Since the year 2000, when the initial publication on brain imaging and genetics was released, imaging genetics has been a rapidly growing research approach with increasing publications every year. Several reviews have been offered to the research community focusing on various study designs. In addition to study design, analytic tools and their proper implementation are also critical to the success of a study. In this review, we survey recent publications using data from neuroimaging and genetics, focusing on methods capturing multivariate effects accommodating the large number of variables from both imaging data and genetic data. We group the analyses of genetic or genomic data into either a prior driven or data driven approach, including gene-set enrichment analysis, multifactor dimensionality reduction, principal component analysis, independent component analysis (ICA, and clustering. For the analyses of imaging data, ICA and extensions of ICA are the most widely used multivariate methods. Given detailed reviews of multivariate analyses of imaging data available elsewhere, we provide a brief summary here that includes a recently proposed method known as independent vector analysis. Finally, we review methods focused on bridging the imaging and genetic data by establishing multivariate and multiple genotype-phenotype associations, including sparse partial least squares, sparse canonical correlation analysis, sparse reduced rank regression and parallel ICA. These methods are designed to extract latent variables from both genetic and imaging data, which become new genotypes and phenotypes, and the links between the new genotype-phenotype pairs are maximized using different cost functions. The relationship between these methods along with their assumptions, advantages, and

Comprehensive analyses of imprinted differentially methylated regions reveal epigenetic and genetic characteristics in hepatoblastoma

International Nuclear Information System (INIS)

Rumbajan, Janette Mareska; Aoki, Shigehisa; Kohashi, Kenichi; Oda, Yoshinao; Hata, Kenichiro; Saji, Tsutomu; Taguchi, Tomoaki; Tajiri, Tatsuro; Soejima, Hidenobu; Joh, Keiichiro; Maeda, Toshiyuki; Souzaki, Ryota; Mitsui, Kazumasa; Higashimoto, Ken; Nakabayashi, Kazuhiko; Yatsuki, Hitomi; Nishioka, Kenichi; Harada, Ryoko

2013-01-01

Aberrant methylation at imprinted differentially methylated regions (DMRs) in human 11p15.5 has been reported in many tumors including hepatoblastoma. However, the methylation status of imprinted DMRs in imprinted loci scattered through the human genome has not been analyzed yet in any tumors. The methylation statuses of 33 imprinted DMRs were analyzed in 12 hepatoblastomas and adjacent normal liver tissue by MALDI-TOF MS and pyrosequencing. Uniparental disomy (UPD) and copy number abnormalities were investigated with DNA polymorphisms. Among 33 DMRs analyzed, 18 showed aberrant methylation in at least 1 tumor. There was large deviation in the incidence of aberrant methylation among the DMRs. KvDMR1 and IGF2-DMR0 were the most frequently hypomethylated DMRs. INPP5Fv2-DMR and RB1-DMR were hypermethylated with high frequencies. Hypomethylation was observed at certain DMRs not only in tumors but also in a small number of adjacent histologically normal liver tissue, whereas hypermethylation was observed only in tumor samples. The methylation levels of long interspersed nuclear element-1 (LINE-1) did not show large differences between tumor tissue and normal liver controls. Chromosomal abnormalities were also found in some tumors. 11p15.5 and 20q13.3 loci showed the frequent occurrence of both genetic and epigenetic alterations. Our analyses revealed tumor-specific aberrant hypermethylation at some imprinted DMRs in 12 hepatoblastomas with additional suggestion for the possibility of hypomethylation prior to tumor development. Some loci showed both genetic and epigenetic alterations with high frequencies. These findings will aid in understanding the development of hepatoblastoma

Model tests and numerical analyses on horizontal impedance functions of inclined single piles embedded in cohesionless soil

Science.gov (United States)

Goit, Chandra Shekhar; Saitoh, Masato

2013-03-01

Horizontal impedance functions of inclined single piles are measured experimentally for model soil-pile systems with both the effects of local soil nonlinearity and resonant characteristics. Two practical pile inclinations of 5° and 10° in addition to a vertical pile embedded in cohesionless soil and subjected to lateral harmonic pile head loadings for a wide range of frequencies are considered. Results obtained with low-to-high amplitude of lateral loadings on model soil-pile systems encased in a laminar shear box show that the local nonlinearities have a profound impact on the horizontal impedance functions of piles. Horizontal impedance functions of inclined piles are found to be smaller than the vertical pile and the values decrease as the angle of pile inclination increases. Distinct values of horizontal impedance functions are obtained for the `positive' and `negative' cycles of harmonic loadings, leading to asymmetric force-displacement relationships for the inclined piles. Validation of these experimental results is carried out through three-dimensional nonlinear finite element analyses, and the results from the numerical models are in good agreement with the experimental data. Sensitivity analyses conducted on the numerical models suggest that the consideration of local nonlinearity at the vicinity of the soil-pile interface influence the response of the soil-pile systems.

A comparative study of cold- and warm-adapted Endonucleases A using sequence analyses and molecular dynamics simulations.

Directory of Open Access Journals (Sweden)

Davide Michetti

Full Text Available The psychrophilic and mesophilic endonucleases A (EndA from Aliivibrio salmonicida (VsEndA and Vibrio cholera (VcEndA have been studied experimentally in terms of the biophysical properties related to thermal adaptation. The analyses of their static X-ray structures was no sufficient to rationalize the determinants of their adaptive traits at the molecular level. Thus, we used Molecular Dynamics (MD simulations to compare the two proteins and unveil their structural and dynamical differences. Our simulations did not show a substantial increase in flexibility in the cold-adapted variant on the nanosecond time scale. The only exception is a more rigid C-terminal region in VcEndA, which is ascribable to a cluster of electrostatic interactions and hydrogen bonds, as also supported by MD simulations of the VsEndA mutant variant where the cluster of interactions was introduced. Moreover, we identified three additional amino acidic substitutions through multiple sequence alignment and the analyses of MD-based protein structure networks. In particular, T120V occurs in the proximity of the catalytic residue H80 and alters the interaction with the residue Y43, which belongs to the second coordination sphere of the Mg2+ ion. This makes T120V an amenable candidate for future experimental mutagenesis.

Dissociation between exact and approximate addition in developmental dyslexia.

Science.gov (United States)

Yang, Xiujie; Meng, Xiangzhi

2016-09-01

Previous research has suggested that number sense and language are involved in number representation and calculation, in which number sense supports approximate arithmetic, and language permits exact enumeration and calculation. Meanwhile, individuals with dyslexia have a core deficit in phonological processing. Based on these findings, we thus hypothesized that children with dyslexia may exhibit exact calculation impairment while doing mental arithmetic. The reaction time and accuracy while doing exact and approximate addition with symbolic Arabic digits and non-symbolic visual arrays of dots were compared between typically developing children and children with dyslexia. Reaction time analyses did not reveal any differences across two groups of children, the accuracies, interestingly, revealed a distinction of approximation and exact addition across two groups of children. Specifically, two groups of children had no differences in approximation. Children with dyslexia, however, had significantly lower accuracy in exact addition in both symbolic and non-symbolic tasks than that of typically developing children. Moreover, linguistic performances were selectively associated with exact calculation across individuals. These results suggested that children with dyslexia have a mental arithmetic deficit specifically in the realm of exact calculation, while their approximation ability is relatively intact. Copyright © 2016 Elsevier Ltd. All rights reserved.

Calculation code used in criticality analyses for the accident of JCO precipitation tank

International Nuclear Information System (INIS)

Miyoshi, Yoshinori

2000-01-01

In order to evaluate nuclear features on criticality accident formed at the nuclear fuel processing facility in Tokai Works of the JCO, Ltd. (JCO), in Tokai-mura, Ibaraki prefecture, dynamic analyses to calculate output change after occurring the accident as well as criticality analyses to calculate reactivity added to precipitation tank, were carried out according to scenario on accident formation. For the criticality analyses, a continuous energy Monte Carlo code MCNP was used to carry out calculation of reactivity fed into the precipitation tank as correctly as possible. And, SRAC code system was used for calculation on temperature and void reactivity coefficients, effective delayed neutron ratio beta eff , and instantaneous neutron generation time required for parameters controlling transition features at criticality accident. In addition, for the dynamic analyses, because of necessity of considering on volume expansion of solution fuels used as exothermic body and radiation decomposition gas forming into solution, output behavior, numbers of nuclear fission, and so forth at initial burst portion were calculated by using TRACE and quasi-regular code, at a center of AGNES-2 promoting on its development in JAERI. Here were reported on outlines and an analysis example on calculation code using for the nuclear features evaluation. (G.K.)

Contesting Citizenship: Comparative Analyses

DEFF Research Database (Denmark)

Siim, Birte; Squires, Judith

2007-01-01

importance of particularized experiences and multiple ineequality agendas). These developments shape the way citizenship is both practiced and analysed. Mapping neat citizenship modles onto distinct nation-states and evaluating these in relation to formal equality is no longer an adequate approach....... Comparative citizenship analyses need to be considered in relation to multipleinequalities and their intersections and to multiple governance and trans-national organisinf. This, in turn, suggests that comparative citizenship analysis needs to consider new spaces in which struggles for equal citizenship occur...

A review and additional post-hoc analyses of the incidence and impact of constipation observed in darifenacin clinical trials

Directory of Open Access Journals (Sweden)

Tack J

2012-09-01

Full Text Available Jan Tack,1 Jean-Jacques Wyndaele,2 Greg Ligozio,3 Mathias Egermark41University of Leuven, Gastroenterology Section, Leuven, 2University of Antwerp, Department of Urology, Antwerp, Belgium; 3Novartis Pharmaceuticals Corporation, NJ, USA; 4Roche Diagnostics Scandinavia AB, Bromma, Sweden and formerly of Novartis Pharma AG, Basel, SwitzerlandBackground: Constipation is a common side effect of antimuscarinic treatment for overactive bladder (OAB. This review evaluates the incidence and impact of constipation on the lives of patients with OAB being treated with darifenacin.Methods: Constipation data from published Phase III and Phase IIIb/IV darifenacin studies were reviewed and analyzed. Over 4000 patients with OAB (aged 18–89 years; ≥80% female enrolled in nine studies (three Phase III [data from these fixed-dose studies were pooled and provide the primary focus for this review], three Phase IIIb, and three Phase IV. The impact of constipation was assessed by discontinuations, use of concomitant laxatives, patient-reported perception of treatment, and a bowel habit questionnaire.Results: In the pooled Phase III trials, 14.8% (50/337 of patients on darifenacin 7.5 mg/day and 21.3% (71/334 on 15 mg/day experienced constipation compared with 12.6% (28/223 and 6.2% (24/388 with tolterodine and placebo, respectively. In addition, a few patients discontinued treatment due to constipation (0.6% [2/337], 1.2% [4/334], 1.8% [4/223], and 0.3% [1/388] in the darifenacin 7.5 mg/day or 15 mg/day, tolterodine, and placebo groups, respectively, or required concomitant laxatives (3.3% [11/337], 6.6% [22/334], 7.2% [16/223], and 1.5% [6/388] in the darifenacin 7.5 mg/day or 15 mg/day, tolterodine, and placebo groups, respectively. Patient-reported perception of treatment quality was observed to be similar between patients who experienced constipation and those who did not. During the long-term extension study, a bowel habit questionnaire showed only small

Additional chromosome abnormalities in chronic myeloid leukemia

Directory of Open Access Journals (Sweden)

Hui-Hua Hsiao

2011-02-01

Full Text Available The Philadelphia (Ph chromosome and/or Breakpoint cluster region-Abelson leukemia virus oncogene transcript are unique markers for chronic myeloid leukemia (CML. However, CML demonstrates heterogeneous presentations and outcomes. We analyzed the cytogenetic and molecular results of CML patients to evaluate their correlation with clinical presentations and outcome. A total of 84 newly diagnosed CML patients were enrolled in the study. Patients were treated according to disease status. Bone marrow samples were obtained to perform cytogenetic and molecular studies. Clinical presentations, treatment courses, and survival were reviewed retrospectively. Among 84 patients, 72 had chronic phase and 12 had accelerated phase CML. Cytogenetic study showed 69 (82.1% with the classic Ph chromosome, 6 (7.2% with a variant Ph chromosome, and 9 (10.7% with additional chromosome abnormalities. Fifty-four (64.3% cases harbored b3a2 transcripts, 29 (34.5% had b2a2 transcript, and 1 had e19a2 transcript. There was no difference in clinical presentations between different cytogenetic and molecular groups; however, additional chromosome abnormalities were significantly associated with the accelerated phase. Imatinib therapy was an effective treatment, as measured by cytogenetic response, when administered as first- and second-line therapy in chronic phase patients. Survival analysis showed that old age, additional chromosome abnormalities, high Sokal score, and no cytogenetic response in second-line therapy had a significant poor impact (p<0.05. In conclusion, we presented the cytogenetic and molecular pattern of CML patients and demonstrated that the additional chromosome abnormality was associated with poor outcome.

Gun Shows and Gun Violence: Fatally Flawed Study Yields Misleading Results

Science.gov (United States)

Hemenway, David; Webster, Daniel; Pierce, Glenn; Braga, Anthony A.

2010-01-01

A widely publicized but unpublished study of the relationship between gun shows and gun violence is being cited in debates about the regulation of gun shows and gun commerce. We believe the study is fatally flawed. A working paper entitled “The Effect of Gun Shows on Gun-Related Deaths: Evidence from California and Texas” outlined this study, which found no association between gun shows and gun-related deaths. We believe the study reflects a limited understanding of gun shows and gun markets and is not statistically powered to detect even an implausibly large effect of gun shows on gun violence. In addition, the research contains serious ascertainment and classification errors, produces results that are sensitive to minor specification changes in key variables and in some cases have no face validity, and is contradicted by 1 of its own authors’ prior research. The study should not be used as evidence in formulating gun policy. PMID:20724672

Database-Driven Analyses of Astronomical Spectra

Science.gov (United States)

Cami, Jan

2012-03-01

species to the fullerene species C60 and C70 [4]. Given the large number and variety of molecules detected in space, molecular infrared spectroscopy can be used to study pretty much any astrophysical environment that is not too energetic to dissociate the molecules. At the lowest energies, it is interesting to note that molecules such as CN have been used to measure the temperature of the Cosmic Microwave Background (see e.g., Ref. 15). The great diagnostic potential of infrared molecular spectroscopy comes at a price though. Extracting the physical parameters from the observations requires expertise in knowing how various physical processes and instrumental characteristics play together in producing the observed spectra. In addition to the astronomical aspects, this often includes interpreting and understanding the limitations of laboratory data and quantum-chemical calculations; the study of the interaction of matter with radiation at microscopic scales (called radiative transfer, akin to ray tracing) and the effects of observing (e.g., smoothing and resampling) on the resulting spectra and possible instrumental effects (e.g., fringes). All this is not trivial. To make matters worse, observational spectra often contain many components, and might include spectral contributions stemming from very different physical conditions. Fully analyzing such observations is thus a time-consuming task that requires mastery of several techniques. And with ever-increasing rates of observational data acquisition, it seems clear that in the near future, some form of automation is required to handle the data stream. It is thus appealing to consider what part of such analyses could be done without too much human intervention. Two different aspects can be separated: the first step involves simply identifying the molecular species present in the observations. Once the molecular inventory is known, we can try to extract the physical parameters from the observed spectral properties. For both

Association between Adult Height and Risk of Colorectal, Lung, and Prostate Cancer: Results from Meta-analyses of Prospective Studies and Mendelian Randomization Analyses

Science.gov (United States)

Khankari, Nikhil K.; Shu, Xiao-Ou; Wen, Wanqing; Kraft, Peter; Lindström, Sara; Peters, Ulrike; Schildkraut, Joellen; Schumacher, Fredrick; Bofetta, Paolo; Risch, Angela; Bickeböller, Heike; Amos, Christopher I.; Easton, Douglas; Gruber, Stephen B.; Haiman, Christopher A.; Hunter, David J.; Chanock, Stephen J.; Pierce, Brandon L.; Zheng, Wei

2016-01-01

Background Observational studies examining associations between adult height and risk of colorectal, prostate, and lung cancers have generated mixed results. We conducted meta-analyses using data from prospective cohort studies and further carried out Mendelian randomization analyses, using height-associated genetic variants identified in a genome-wide association study (GWAS), to evaluate the association of adult height with these cancers. Methods and Findings A systematic review of prospective studies was conducted using the PubMed, Embase, and Web of Science databases. Using meta-analyses, results obtained from 62 studies were summarized for the association of a 10-cm increase in height with cancer risk. Mendelian randomization analyses were conducted using summary statistics obtained for 423 genetic variants identified from a recent GWAS of adult height and from a cancer genetics consortium study of multiple cancers that included 47,800 cases and 81,353 controls. For a 10-cm increase in height, the summary relative risks derived from the meta-analyses of prospective studies were 1.12 (95% CI 1.10, 1.15), 1.07 (95% CI 1.05, 1.10), and 1.06 (95% CI 1.02, 1.11) for colorectal, prostate, and lung cancers, respectively. Mendelian randomization analyses showed increased risks of colorectal (odds ratio [OR] = 1.58, 95% CI 1.14, 2.18) and lung cancer (OR = 1.10, 95% CI 1.00, 1.22) associated with each 10-cm increase in genetically predicted height. No association was observed for prostate cancer (OR = 1.03, 95% CI 0.92, 1.15). Our meta-analysis was limited to published studies. The sample size for the Mendelian randomization analysis of colorectal cancer was relatively small, thus affecting the precision of the point estimate. Conclusions Our study provides evidence for a potential causal association of adult height with the risk of colorectal and lung cancers and suggests that certain genetic factors and biological pathways affecting adult height may also affect the

Strong-stability-preserving additive linear multistep methods

KAUST Repository

Hadjimichael, Yiannis

2018-02-20

The analysis of strong-stability-preserving (SSP) linear multistep methods is extended to semi-discretized problems for which different terms on the right-hand side satisfy different forward Euler (or circle) conditions. Optimal perturbed and additive monotonicity-preserving linear multistep methods are studied in the context of such problems. Optimal perturbed methods attain larger monotonicity-preserving step sizes when the different forward Euler conditions are taken into account. On the other hand, we show that optimal SSP additive methods achieve a monotonicity-preserving step-size restriction no better than that of the corresponding nonadditive SSP linear multistep methods.

Studies of alumina additions in zirconia - magnesia

International Nuclear Information System (INIS)

Muccillo, R.

1987-01-01

Ionic conductivity measurements have been carried out in the 500 0 C - 1000 0 C temperature range in Mg - PSZ (Partially Stabilized Zirconia) with 0.5 to 10 mol % alumina additions. All specimens were prepared by pressing followed by pre - and sintering at 1000 0 C/2h and1450 0 C/4h, respectively. Thermal histerysis of the ionic conductivity have been detected, probably due to phase changes in the Mg-PSZ samples. The results show that alumina additions up to 2.1% enhances densification with no major variations in electrical resistivity values. (Author) [pt

Combining Conversation Analysis and Nexus Analysis to analyse sociomaterial and affective practices

DEFF Research Database (Denmark)

Raudaskoski, Pirkko Liisa

2016-01-01

of resemiotization (Iedema 2000). Within organization and design studies, materiality has become a focus in the increasingly popular sociomaterial approach to everyday practices (e.g. Orlikowski 2007). Some sociomaterial scholars (e.g. Sørensen 2013) analyse ethnographic data either as evidence for the sociomaterial....... The analytical effort is to get to the senses and sensations which are regarded as opposite of sense-making. In my presentation, I go through some of my own analyses from various institutional interactions to show how CA-based multimodal analyses of local interactional (or intra-actional) trajectories combined...... configuration, also as an interdisciplinary offer for an analytic package that might help sociomaterial researchers of practices come even closer to the situation at hand as an assemblage out of which materials, humans and experiences emerge....

Additives for cement compositions based on modified peat

Energy Technology Data Exchange (ETDEWEB)

Kopanitsa, Natalya, E-mail: kopanitsa@mail.ru; Sarkisov, Yurij, E-mail: sarkisov@tsuab.ru; Gorshkova, Aleksandra, E-mail: kasatkina.alexandra@gmail.com; Demyanenko, Olga, E-mail: angel-n@sibmail.com [Tomsk State University of Architecture and Building, 2, Solyanaya sq., Tomsk, 634003 (Russian Federation)

2016-01-15

High quality competitive dry building mixes require modifying additives for various purposes to be included in their composition. There is insufficient amount of quality additives having stable properties for controlling the properties of cement compositions produced in Russia. Using of foreign modifying additives leads to significant increasing of the final cost of the product. The cost of imported modifiers in the composition of the dry building mixes can be up to 90% of the material cost, depending on the composition complexity. Thus, the problem of import substitution becomes relevant, especially in recent years, due to difficult economic situation. The article discusses the possibility of using local raw materials as a basis for obtaining dry building mixtures components. The properties of organo-mineral additives for cement compositions based on thermally modified peat raw materials are studied. Studies of the structure and composition of the additives are carried out by physicochemical research methods: electron microscopy and X-ray analysis. Results of experimental research showed that the peat additives contribute to improving of cement-sand mortar strength and hydrophysical properties.

Validation of endogenous normalizing genes for expression analyses in adult human testis and germ cell neoplasms.

Science.gov (United States)

Svingen, T; Jørgensen, A; Rajpert-De Meyts, E

2014-08-01

The measurement of gene expression levels in cells and tissues typically depends on a suitable point of reference for inferring biological relevance. For quantitative (or real-time) RT-PCR assays, the method of choice is often to normalize gene expression data to an endogenous gene that is stably expressed across the samples analysed: a so-called normalizing or housekeeping gene. Although this is a valid strategy, the identification of stable normalizing genes has proved challenging and a gene showing stable expression across all cells or tissues is unlikely to exist. Therefore, it is necessary to define suitable normalizing genes for specific cells and tissues. Here, we report on the performance of a panel of nine commonly employed normalizing genes in adult human testis and testicular pathologies. Our analyses revealed significant variability in transcript abundance for commonly used normalizers, highlighting the importance of selecting appropriate normalizing genes as comparative measurements can yield variable results when different normalizing genes are employed. Based on our results, we recommend using RPS20, RPS29 or SRSF4 when analysing relative gene expression levels in human testis and associated testicular pathologies. OCT4 and SALL4 can be used with caution as second-tier normalizers when determining changes in gene expression in germ cells and germ cell tumour components, but the relative transcript abundance appears variable between different germ cell tumour types. We further recommend that such studies should be accompanied by additional assessment of histology and cellularity of each sample. © The Author 2014. Published by Oxford University Press on behalf of the European Society of Human Reproduction and Embryology. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Multi-element isotope dilution analyses using ICP-MS

International Nuclear Information System (INIS)

Volpe, A.M.

1996-01-01

Presently, 37 elements ranging from light (Li,B) through transition metals, noble, rare earth and heavy elements, to actinides and transuranics (Pu, Am, Cm) are measured by isotope dilution at Lawrence Livermore National Laboratory. Projects range from geological and hydrological to biological. The research goal is to measure accurately many elements present in diverse matrices at trace (ppb) levels using isotope dilution methods. Major advantages of isotope dilution methods are accuracy, elimination of ion intensity calibration, and quantitation for samples that require chemical separation. Accuracy depends on tracer isotope calibration, tracer-sample isotopic equilibration, and appropriate background, isobaric and mass bias corrections. Propagation of isotope ratio error due to improper tracer isotope addition is a major concern with multi-element analyses when abundances vary widely. 11 refs., 3 figs

MAAP - modular program for analyses of severe accidents

International Nuclear Information System (INIS)

Henry, R.E.; Lutz, R.J.

1990-01-01

The MAAP computer code was developed by Westinghouse as a fast, user-friendly, integrated analytical tool for evaluations of the sequences and consequences of severe accidents. The code allows a fully integrated treatment of thermohydraulic behavior and of the fission products in the primary system, the containment, and the ancillary buildings. This ensures interactive inclusion of all thermohydraulic events and of fission product behavior. All important phenomena which may occur in a major accident are contained in the modular code. In addition, many of the important parameters affecting the multitude of different phenomena can be defined by the user. In this way, it is possible to study the accuracy of the predicted course and of the consequences of a series of major accident phenomena. The MAAP code was subjected to extensive benchmarking with respect to the results of the experimental and theoretical programs, the findings obtained in other safety analyses using computers and data from accidents and transients in plants actually in operation. With the expected connection of the validation and test programs, the computer code attains a quality standard meeting the most stringent requirements in safety analyses. The code will be enlarged further in order to expand the number of benchmarks and the resolution of individual comparisons, and to ensure that future MAAP models will be in better agreement with the experiments and experiences of industry. (orig.) [de

Seminal vesicle intrafraction motion analysed with cinematic magnetic resonance imaging

International Nuclear Information System (INIS)

Gill, Suki; Dang, Kim; Fox, Chris; Bressel, Mathias; Kron, Tomas; Bergen, Noelene; Ferris, Nick; Owen, Rebecca; Chander, Sarat; Tai, Keen Hun; Foroudi, Farshad

2014-01-01

This study analyses seminal vesicle displacement relative to the prostate and in relation to treatment time. A group of eleven patients undergoing prostate cancer radiotherapy were imaged with a continuous 3 T cine-MRI in the standard treatment setup position. Four images were recorded every 4 seconds for 15 minutes in the sagittal plane and every 6.5 seconds for 12 minutes in the coronal plane. The prostate gland and seminal vesicles were contoured on each MRI image. The coordinates of the centroid of the prostate and seminal vesicles on each image was analysed for displacement against time. Displacements between the 2.5 percentile and 97.5 percentile (i.e. the 2.5% trimmed range) for prostate and seminal vesicle centroid displacements were measured for 3, 5, 10 and 15 minutes time intervals in the anterior-posterior (AP), left-right (LR) and superior-inferior (SI) directions. Real time prostate and seminal vesicle displacement was compared for individual patients. The 2.5% trimmed range for 3, 5, 10 and 15 minutes for the seminal vesicle centroids in the SI direction measured 4.7 mm; 5.8 mm; 6.5 mm and 7.2 mm respectively. In the AP direction, it was 4.0 mm, 4.5 mm, 6.5 mm, and 7.0 mm. In the LR direction for 3, 5 and 10 minutes; for the left seminal vesicle, it was 2.7 mm, 2.8 mm, 3.4 mm and for the right seminal vesicle, it was 3.4 mm, 3.3 mm, and 3.4 mm. The correlation between the real-time prostate and seminal vesicle displacement varied substantially between patients indicating that the relationship between prostate displacement and seminal vesicles displacement is patient specific with the majority of the patients not having a strong relationship. Our study shows that seminal vesicle motion increases with treatment time, and that the prostate and seminal vesicle centroids do not move in unison in real time, and that an additional margin is required for independent seminal vesicle motion if treatment localisation is to the prostate

Effect of different phytogenic additives on oxidation stability of chicken meat

Directory of Open Access Journals (Sweden)

Marek Bobko

2016-05-01

Full Text Available The aim of the study was to evaluate the oxidative stability (TBARS method of breast and thigh muscle after application of feed mixtures enriched by phytogenic additives. The experiment started with 150 pieces one-day-old chicks of Cobb 500 hybrid combination. They were divided into one control (C and two experimental groups (1st EG and 2nd EG. Each group included 50 chicks. In experimental groups, feed additives were applied as followed: 100 mg.kg-1 Agolin Poultry (in the 1st EG and 500 mg.kg-1 Agolin Tannin Plus (in the 2nd EG. Experimental broiler chickens were fed during 42 days by ad libitum. Chicken meat samples of breast and thigh muscle were analysed in the 1st day, 1st, 2nd, 3rd, 4th, 5th and 6th month of storage in frozen storage at -18 °C. We recorded positive influence on chicken meat oxidative stability in all experimental groups with application of phytogenic feed additives. Obtained results showed that applied phytogenic additives had positive influence on oxidative stability of breast and thigh muscles. At the end of frozen storage (in 6th month, we found higher malondialdehyde (MDA values and lower oxidative stability (p <0.05 of breast muscle in control group (0.167 mg.kg-1 compared to experimental groups (from 0.150 mg.kg-1 in 1. EG to 0.155 mg.kg-1 in 2. EG. In the thigh muscle, we found similar tendency of oxidative changes as in the breast muscle. At the end of frozen storage (in the 6th month, MDA average values of thigh muscle were higher (p <0.05 in control group (0.181 mg.kg-1 compared to experimental groups (1. EG 0.164 mg.kg-1 and 2. EG 0.169 mg.kg-1. Significant differences (p <0.05 between the control and experimental groups were found from the 5th month of storage in thigh and breast muscle. Obtained results indicate positive influence of phytogenic additives applied in chicken nutrition, namely on stabilization of fatty substance to degradation processes. Normal 0 21 false false false SK X-NONE X-NONE Normal 0

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Science.gov (United States)

Boissy, Robert J; Romberger, Debra J; Roughead, William A; Weissenburger-Moser, Lisa; Poole, Jill A; LeVan, Tricia D

2014-01-01

Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance). The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70%) at the phylum level, Clostridia (44%) at the Class level, and Clostridiales at the Order level (41%). In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the bioinformatic analyses

Shotgun pyrosequencing metagenomic analyses of dusts from swine confinement and grain facilities.

Directory of Open Access Journals (Sweden)

Robert J Boissy

Full Text Available Inhalation of agricultural dusts causes inflammatory reactions and symptoms such as headache, fever, and malaise, which can progress to chronic airway inflammation and associated diseases, e.g. asthma, chronic bronchitis, chronic obstructive pulmonary disease, and hypersensitivity pneumonitis. Although in many agricultural environments feed particles are the major constituent of these dusts, the inflammatory responses that they provoke are likely attributable to particle-associated bacteria, archaebacteria, fungi, and viruses. In this study, we performed shotgun pyrosequencing metagenomic analyses of DNA from dusts from swine confinement facilities or grain elevators, with comparisons to dusts from pet-free households. DNA sequence alignment showed that 19% or 62% of shotgun pyrosequencing metagenomic DNA sequence reads from swine facility or household dusts, respectively, were of swine or human origin, respectively. In contrast only 2% of such reads from grain elevator dust were of mammalian origin. These metagenomic shotgun reads of mammalian origin were excluded from our analyses of agricultural dust microbiota. The ten most prevalent bacterial taxa identified in swine facility compared to grain elevator or household dust were comprised of 75%, 16%, and 42% gram-positive organisms, respectively. Four of the top five swine facility dust genera were assignable (Clostridium, Lactobacillus, Ruminococcus, and Eubacterium, ranging from 4% to 19% relative abundance. The relative abundances of these four genera were lower in dust from grain elevators or pet-free households. These analyses also highlighted the predominance in swine facility dust of Firmicutes (70% at the phylum level, Clostridia (44% at the Class level, and Clostridiales at the Order level (41%. In summary, shotgun pyrosequencing metagenomic analyses of agricultural dusts show that they differ qualitatively and quantitatively at the level of microbial taxa present, and that the

Performance assessment analyses unique to Department of Energy spent nuclear fuel

International Nuclear Information System (INIS)

Loo, H.H.; Duguid, J.J.

2000-01-01

This paper describes the iterative process of grouping and performance assessment that has led to the current grouping of the U.S. Department of Energy (DOE) spent nuclear fuel (SNF). The unique sensitivity analyses that form the basis for incorporating DOE fuel into the total system performance assessment (TSPA) base case model are described. In addition, the chemistry that results from dissolution of DOE fuel and high level waste (HLW) glass in a failed co-disposal package, and the effects of disposal of selected DOE SNF in high integrity cans are presented

Artificial sweeteners and mixture of food additives cause to break oral tolerance and induce food allergy in murine oral tolerance model for food allergy.

Science.gov (United States)

Yamashita, H; Matsuhara, H; Miotani, S; Sako, Y; Matsui, T; Tanaka, H; Inagaki, N

2017-09-01

Processed foods are part of daily life. Almost all processed foods contain food additives such as sweeteners, preservatives and colourants. From childhood, it is difficult to avoid consuming food additives. It is thought that oral tolerance for food antigens is acquired during early life. If tolerance fails, adverse immune responses to food proteins may occur. We hypothesized that food additives prevent acquisition of oral tolerance and aimed to verify the safety of food additives. We induced experimental oral tolerance in mice for ovalbumin (OVA), a food antigen, by previous oral treatment with OVA before sensitization with OVA injections. Food additives were administered at the induction of oral tolerance, and food allergy was induced by repeated administration of OVA. Symptoms of food allergy were defined as a change in body temperature and allergic diarrhoea. Saccharin sodium and a mixture of food additives inhibited acquisition of oral tolerance. Hypothermia and allergic diarrhoea with elevation of OVA-specific IgE were induced in the murine model of oral tolerance. Analyses of antigen-presenting cells in mesenteric lymph nodes showed that food additives affected their manner of migration. Additionally, food additives decreased the proportion of CD25 hi regulatory T cells among CD4 + T cells in the mesenteric lymph nodes. A large amount of food additives may prevent acquisition of oral tolerance. Intake of food additives in early life may increase the risk of food allergies. © 2017 John Wiley & Sons Ltd.

Addition of electric arc furnace dust in hot metal changing the form of addition

International Nuclear Information System (INIS)

Marques Sobrinho, Vicente de Paulo Ferreira; Oliveira, Jose Roberto de; Vieira, Estefano Aparecido; Telles, Victor Bridi; Grillo, Felipe Fardin; Tenorio, Jorge Alberto Soares; Espinosa, Denise Crocce Romano

2014-01-01

This research aims to study the incorporation of the mass of electric arc furnace dust (EAFD), by addition in hot metal (1.78% Si) at a temperature of 1,400 degrees Celsius. The EAFD is from a steel plant producing long steel. The addition of the EAFD was as received, in the form of briquettes without agitation of the hot metal and in the form of briquettes with agitation of the hot metal. Previously, the EAFD was characterized using the following techniques: chemical analysis, size analysis, X-ray diffraction, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) microanalysis. The achievement of fusion experiments in laboratory scale, took place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of EAFD mass used graphite crucibles. After cooling, the hot metal and the slag, remaining in the crucible, were weighed to do a mass balance. A flow of inert gas (argon) was maintained inside the furnace during the experiments. Results show that the experiment with addition of EAFD as received presents the best result of incorporating the mass of the final hot metal (1.73%) combined with the lowest percentage of volatilized mass of EAFD (46.52%). The experiment addition of EAFD in the form of briquette with agitation of hot metal presents the lowest percentage of slag mass (4.58%). The zinc content of volatilized EAFD (64.30%) is higher than the zinc content of the imported ore concentrate (52%) and zinc content of the national ore concentrate (12% to 39%). The presence of lead and cadmium in the slag characterizing it as a hazardous solid waste. (author)

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

Radon in Austrian tourist mines and show caves

International Nuclear Information System (INIS)

Ringer, W.; Graeser, J.

2009-01-01

The radon situation in tourist mines and show caves is barely investigated in Austria. This paper investigates the influence of its determining factors, such as climate, structure and geology. For this purpose, long-term time-resolved measurements over 6 to 12 months in 4 tourist mines and 2 show caves - with 5 to 9 measuring points each - have been carried out to obtain the course of radon concentration throughout the year. In addition, temperature and air-pressure were measured and compared to the data outside where available. Results suggest that the dominating factors of the average radon concentration are structure and location (geology) of the tunnel-system, whereas the diurnal and annual variation is mainly caused by the changing airflow, which is driven by the difference in temperature inside and outside. Downcast air is connected with very low radon concentrations, upcast air with high concentrations. In some locations the maximum values appear when the airflow ceases. But airflow can be different in different parts of mines and caves. Systems close to the surface show generally lower radon levels than the ones located deeper underground. Due to variation of structure, geology and local climate, the radon situation in mines and caves can only be described by simultaneous measurements at several measuring points. (orig.)

Preliminary Results of Ancillary Safety Analyses Supporting TREAT LEU Conversion Activities

Energy Technology Data Exchange (ETDEWEB)

Brunett, A. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Fei, T. [Argonne National Lab. (ANL), Argonne, IL (United States); Strons, P. S. [Argonne National Lab. (ANL), Argonne, IL (United States); Papadias, D. D. [Argonne National Lab. (ANL), Argonne, IL (United States); Hoffman, E. A. [Argonne National Lab. (ANL), Argonne, IL (United States); Kontogeorgakos, D. C. [Argonne National Lab. (ANL), Argonne, IL (United States); Connaway, H. M. [Argonne National Lab. (ANL), Argonne, IL (United States); Wright, A. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-10-01

Report (FSAR) [3]. Depending on the availability of historical data derived from HEU TREAT operation, results calculated for the LEU core are compared to measurements obtained from HEU TREAT operation. While all analyses in this report are largely considered complete and have been reviewed for technical content, it is important to note that all topics will be revisited once the LEU design approaches its final stages of maturity. For most safety significant issues, it is expected that the analyses presented here will be bounding, but additional calculations will be performed as necessary to support safety analyses and safety documentation. It should also be noted that these analyses were completed as the LEU design evolved, and therefore utilized different LEU reference designs. Preliminary shielding, neutronic, and thermal hydraulic analyses have been completed and have generally demonstrated that the various LEU core designs will satisfy existing safety limits and standards also satisfied by the existing HEU core. These analyses include the assessment of the dose rate in the hodoscope room, near a loaded fuel transfer cask, above the fuel storage area, and near the HEPA filters. The potential change in the concentration of tramp uranium and change in neutron flux reaching instrumentation has also been assessed. Safety-significant thermal hydraulic items addressed in this report include thermally-induced mechanical distortion of the grid plate, and heating in the radial reflector.

Benchmark exercises on PWR level-1 PSA (step 3). Analyses of accident sequence and conclusions

International Nuclear Information System (INIS)

Niwa, Yuji; Takahashi, Hideaki.

1996-01-01

The results of level 1 PSA generate fluctuations due to the assumptions based on several engineering judgements set in the stages of PSA analysis. On the purpose of the investigation of uncertainties due to assumptions, three kinds of a standard problem, what we call benchmark exercise have been set. In this report, sensitivity studies (benchmark exercise) of sequence analyses are treated and conclusions are mentioned. The treatment of inter-system dependency would generate uncertainly of PSA. In addition, as a conclusion of the PSA benchmark exercise, several findings in the sequence analysis together with previous benchmark analyses in earlier INSS Journals are treated. (author)

Fuel additive improves plant`s air quality

Energy Technology Data Exchange (ETDEWEB)

Kratch, K.

1995-07-01

Employees of a major pulp and paper manufacturer complained to the Michigan Department of Public Health that emissions from liquefied petroleum gas-powered fork-lifts used in one of the facility`s warehouses were making them ill. The new and tight building was locking in carbon monoxide emissions, according to the plant`s vehicle maintenance supervisor. Although LPG is a clean-burning fuel, it absorbs impurities from pipelines, resulting in emissions problems. After the company introduced a fuel additive to the LPG, employees` symptoms disappeared. According to the maintenance supervisor, there have been no complaints since the additive was introduced five years ago. A major US auto manufacturer also found the additive helpful in reducing carbon monoxide emissions from forklift trucks in a large parts warehouse to levels within OSHA limits. The carmaker conducted a test of 10 forklifts at its Toledo, Ohio, plant to determine the additive`s effectiveness. Trucks were equipped with new or rebuilt vaporizers, and their carburetors were adjusted for the lowest carbon monoxide and hydrocarbon emissions levels prior to the test. According to Advanced Technology, five trucks were filled with LPG and treated with CGX-4, and five used fuel from the same stock but without the additive. All were operated 16 hours a day, six days a week without further tuning or adjusting. Carbon monoxide and hydrocarbon emissions were measured at 30-, 45- and 65-day intervals. Test results show that all of the trucks using the additive maintained low levels of carbon monoxide and hydrocarbon emissions longer than trucks not using the additive.

Non-destructive XRF analyses of fine-grained basalts from Eiao, Marquesas Islands

International Nuclear Information System (INIS)

Charleux, M.; McAlister, A.; Mills, P.R.; Lundblad, S.P.

2014-01-01

The Marquesan island of Eiao was an important source of fine-grained basalt in Central East Polynesia, with examples being identified in archaeological assemblages throughout the region. However, compared to many other large-scale Polynesian basalt sources, little has been published about the physical extent and geochemical variability of tool-quality basalt on Eiao; prior to our study, only a single site with evidence of stone extraction had been identified and geochemical information was limited to less than two dozen samples. In this paper we report geochemical data for 225 additional basalt specimens collected on Eiao. Our analyses were conducted non-destructively using three EDXRF instruments: one lab-based unit and two portable analysers. The majority of our sample, identified here as Group 1, possesses geochemical and physical characteristics similar to those reported in previous studies. Group 1 samples were collected from various locations on Eiao suggesting that, rather than being limited to a single quarry site, fine-grained basalt was extracted from multiple sources throughout the island. In addition, we identified a second group (Group 2), which possesses a distinct geochemistry, a coarser grain and often an unusual reddish colour. Evidence from Eiao indicates that Group 2 stone was regularly utilised and our analysis of an adze collected on Hiva Oa Island suggests that this material was distributed at least as far as the southern Marquesas. (author)

SOCR Analyses - an Instructional Java Web-based Statistical Analysis Toolkit.

Science.gov (United States)

Chu, Annie; Cui, Jenny; Dinov, Ivo D

2009-03-01

The Statistical Online Computational Resource (SOCR) designs web-based tools for educational use in a variety of undergraduate courses (Dinov 2006). Several studies have demonstrated that these resources significantly improve students' motivation and learning experiences (Dinov et al. 2008). SOCR Analyses is a new component that concentrates on data modeling and analysis using parametric and non-parametric techniques supported with graphical model diagnostics. Currently implemented analyses include commonly used models in undergraduate statistics courses like linear models (Simple Linear Regression, Multiple Linear Regression, One-Way and Two-Way ANOVA). In addition, we implemented tests for sample comparisons, such as t-test in the parametric category; and Wilcoxon rank sum test, Kruskal-Wallis test, Friedman's test, in the non-parametric category. SOCR Analyses also include several hypothesis test models, such as Contingency tables, Friedman's test and Fisher's exact test.The code itself is open source (http://socr.googlecode.com/), hoping to contribute to the efforts of the statistical computing community. The code includes functionality for each specific analysis model and it has general utilities that can be applied in various statistical computing tasks. For example, concrete methods with API (Application Programming Interface) have been implemented in statistical summary, least square solutions of general linear models, rank calculations, etc. HTML interfaces, tutorials, source code, activities, and data are freely available via the web (www.SOCR.ucla.edu). Code examples for developers and demos for educators are provided on the SOCR Wiki website.In this article, the pedagogical utilization of the SOCR Analyses is discussed, as well as the underlying design framework. As the SOCR project is on-going and more functions and tools are being added to it, these resources are constantly improved. The reader is strongly encouraged to check the SOCR site for most

Red mud addition in the raw meal for the production of Portland cement clinker.

Science.gov (United States)

Tsakiridis, P E; Agatzini-Leonardou, S; Oustadakis, P

2004-12-10

The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste, which is obtained from bauxite during the Bayer process for alumina production, in the raw meal for the production of Portland cement clinker. For that reason, two samples of raw meals were prepared: one with ordinary raw materials, as a reference sample ((PC)Ref), and another with 3.5% red mud ((PC)R/M). The effect on the reactivity of the raw mix was evaluated on the basis of the unreacted lime content in samples sintered at 1350, 1400 and 1450 degrees C. Subsequently, the clinkers were produced by sintering the two raw meals at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the red mud did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting time, compressive strength and expansibility. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the red mud did not negatively affect the quality of the produced cement.

Evaluation of PCDD/Fs characterization in animal feed and feed additives.

Science.gov (United States)

Kim, MeeKyung; Kim, Sooyeon; Yun, Seon Jong; Kwon, Jin-Wook; Son, Seong-Wan

2007-09-01

Safety control of feed and feed additives is necessary to have safe food of animal origin. Based on media reports, nine incidents regarding dioxins and/or PCBs contaminations occurred worldwide during the last decade. Korea is a country which imports feed and feed additives. In this study, various kinds of feed and feed additives were analyzed to monitor the contamination level of dioxins. The level of PCDD/Fs in fish oil was the highest with a concentration of 23.33ngkg(-1), which is equivalent to a toxicological concentration of 4.68ngWHO-TEQ/kg. Feed from animals origin such as chicken meal, animal fat, fish meal, fish oil, and shell powder showed relatively higher concentrations of PCDD/Fs. Feed from plants origin, minerals, and additives ranged from non-detects for bit pulp and ethoxyquin to 8.28ngkg(-1) for dl-methionine. From a toxicological point of view, the highest concentration in vitamins was 0.08ngWHO-TEQ/kg among the feed additives. 2,3,4,7,8-PeCDF was the dominant congener in samples of fish oil, fish meal, and shell powder. Animal fat showed that the pattern of PCDD/Fs depends on the sources of contamination. A sample of animal fat showed 1,2,3,4,7,8-HxCDF and the other sample showed 1,2,3,4,7,8-HxCDD as a primary congener. Generally, low levels of PCDDs were detected in feed additives. Patterns of PCDD/Fs in choline chloride were different with that in choline chloride from an incident in Europe in 2000.

Non-trauma-associated additional findings in whole-body CT examinations in patients with multiple trauma

International Nuclear Information System (INIS)

Hoffstetter, P.; Herold, T.; Daneschnejad, M.; Zorger, N.; Jung, E.M.; Feuerbach, S.; Schreyer, A.G.

2008-01-01

Purpose: whole-body CT scans for patients with multiple trauma represent an increasingly accepted first diagnostic tool. The multidetector approach in particular provides appropriate diagnostic algorithms for detecting nearly all relevant traumatic findings in a short time with a high grade of sensitivity and specificity. Non-trauma-associated additional findings are commonly depicted based on these CT examinations. The aim of this study is to evaluate the number and quality of these additional findings in consecutive patients with multiple trauma. Materials and methods: between 3/04 and 8/06 we scanned 304 patients according to our dedicated multiple trauma protocol. The examination protocol includes a head scan without intravenous contrast followed by a whole-body scan including the neck, thorax and abdomen acquired by a 16-row CT Scanner (Siemens, Sensation 16). The CT scans were retrospectively analyzed by two radiologists with respect to non-trauma-associated findings. Lesions were assessed according to their clinical relevance (highly relevant, moderately relevant, not relevant). For patients with highly relevant findings, additional follow-up research was performed. Results: The average age was 43 years (range 3 - 92). 236 of the patients were male (77.6%), 68 female (22.4%). 153 patients (50.3%) had additional non-trauma-associated findings. In 20 cases (6.6%) lesions with high clinical relevance were detected (e.g. carcinoma of the kidney or the ovary). In 71 patients (23.4%) findings with moderate relevance were described. In 63 patients (20.7%) additional findings without major relevance were diagnosed. Conclusion: Whole-body CT scans of patients randomized by a trauma show a considerable number of non-trauma-associated additional findings. In about 30% of cases, these findings are clinically relevant because further diagnostic workup or treatment in the short or medium-term is needed. The results of these analyses emphasize the diagnostic value of CT

Thermo-mechanical properties of poly ε-caprolactone/poly L-lactic acid blends: addition of nalidixic acid and polyethylene glycol additives.

Science.gov (United States)

Douglas, P; Albadarin, Ahmad B; Al-Muhtaseb, Ala'a H; Mangwandi, Chirangano; Walker, G M

2015-05-01

The search for ideal biomaterials is still on-going for tissue regeneration. In this study, blends of poly ε-caprolactone (PCL) with poly l-lactic acid (PLLA), nalidixic acid (NA) and polyethylene glycol (PEG) were prepared. Mechanical and thermal properties of the blends were investigated by tensile and flexural analysis, DSC, TGA, WXRD, MFI, BET, SEM and hot stage optical microscopy. Results showed that the loading of PLLA caused a significant decrease in tensile strength and almost total eradication of the elongation at break of PCL matrix, especially after PEG and NA addition. Increased stiffness was also noted with additional NA, PEG and PLLA, resulting in an increase in the flexural modulus of the blends. Isothermal degradation indicated that bulk PCL, PLLA and the blends were thermally stable at 200°C for the duration of 2h making extrusion of the blends at this temperature viable. Morphological study showed that increasing the PLLA content and addition of the very low viscosity PEG and powder NA decreased the Melt Flow Indexer and increased the viscosity. At the higher temperature, the PLLA begins to soften and eventually melts allowing for increased flow and, coupling this with, the natural increase in MFI caused by temperature is enhanced further. The PEG and NA addition increased dramatically the pore volume which is important for cell growth and flow transport of nutrients and metabolic waste. Copyright © 2015 Elsevier Ltd. All rights reserved.

Real-Time Soils Characterization and Analyses Systems Used at Ohio Closure Sites

International Nuclear Information System (INIS)

Roybal, Lyle Gene; Carpenter, Michael Vance; Giles, John Robert; Hartwell, John Kelvin; Danahy, R.

2003-01-01

The Idaho National Engineering and Environmental Laboratory (INEEL) and the Fernald Environmental Management Project (FEMP) have jointly developed a field-deployed analytical system to rapidly scan, characterize, and analyze surface soil contamination. The basic system consists of a sodium iodide (NaI) spectrometer and global positioning system (GPS) hardware. This hardware can be deployed from any of four different platforms depending on the scope of the survey at hand. These platforms range from a large tractor-based unit (the RTRAK) used to survey large, relatively flat areas to a hand-pushed unit where maneuverability is important, to an excavator mounted system used to scan pits and trenches. The mobile sodium iodide concept was initially developed by the FEMP to provide pre-screening analyses for soils contaminated with uranium, thorium, and radium. The initial study is documented in the RTRAK Applicability Study and provides analyses supporting the field usage of the concept. The RTRAK system produced data that required several days of post-processing and analyses to generate an estimation of field coverage and activity levels. The INEEL has provided integrated engineering, computer hardware and software support to greatly streamline the data acquisition and analysis process to the point where real-time activity and coverage maps are available to the field technicians. On-line analyses have been added to automatically convert GPS data to Ohio State-Plane coordinates, examine and correct collected spectra for energy calibration drifts common to NaI spectrometers, and strip spectra in regions of interest to provide moisture corrected activity levels for total uranium, thorium-232, and radium-226. Additionally, the software provides a number of checks and alarms to alert operators that a hand-examination of spectral data in a particular area may be required. The FEMP has estimated that this technology has produced projected site savings in excess of $34M

Nosocomial HIV-transmission in an outpatient clinic detected by epidemiologicaland phylogenetic analyses

DEFF Research Database (Denmark)

Katzenstein, T.L.; Jørgensen, L.B.; H, Permin

1999-01-01

.9% respectively. In addition, GP harboured HIV RNA with a foscarnet resistance mutation further lendingsupport to virus from the foscarnet-treated FDL being the source of the infection. Interestingly, GP experienced increases inimmunoglobulin production after contracting the HIV-infection, and decreases after...... antiretroviral-induced viral suppression. Aclinical procedure which, under stressful conditions, could lead to breaches in infection control measures was identified. The source ofthe infection was most likely a contaminated multidose vial. CONCLUSION: Through epidemiological and phylogenetic analyses acase...

Identifying null meta-analyses that are ripe for updating

Directory of Open Access Journals (Sweden)

Fang Manchun

2003-07-01

Full Text Available Abstract Background As an increasingly large number of meta-analyses are published, quantitative methods are needed to help clinicians and systematic review teams determine when meta-analyses are not up to date. Methods We propose new methods for determining when non-significant meta-analytic results might be overturned, based on a prediction of the number of participants required in new studies. To guide decision making, we introduce the "new participant ratio", the ratio of the actual number of participants in new studies to the predicted number required to obtain statistical significance. A simulation study was conducted to study the performance of our methods and a real meta-analysis provides further evidence. Results In our three simulation configurations, our diagnostic test for determining whether a meta-analysis is out of date had sensitivity of 55%, 62%, and 49% with corresponding specificity of 85%, 80%, and 90% respectively. Conclusions Simulations suggest that our methods are able to detect out-of-date meta-analyses. These quick and approximate methods show promise for use by systematic review teams to help decide whether to commit the considerable resources required to update a meta-analysis. Further investigation and evaluation of the methods is required before they can be recommended for general use.

Consensuses and discrepancies of basin-scale ocean heat content changes in different ocean analyses

Science.gov (United States)

Wang, Gongjie; Cheng, Lijing; Abraham, John; Li, Chongyin

2018-04-01

Inconsistent global/basin ocean heat content (OHC) changes were found in different ocean subsurface temperature analyses, especially in recent studies related to the slowdown in global surface temperature rise. This finding challenges the reliability of the ocean subsurface temperature analyses and motivates a more comprehensive inter-comparison between the analyses. Here we compare the OHC changes in three ocean analyses (Ishii, EN4 and IAP) to investigate the uncertainty in OHC in four major ocean basins from decadal to multi-decadal scales. First, all products show an increase of OHC since 1970 in each ocean basin revealing a robust warming, although the warming rates are not identical. The geographical patterns, the key modes and the vertical structure of OHC changes are consistent among the three datasets, implying that the main OHC variabilities can be robustly represented. However, large discrepancies are found in the percentage of basinal ocean heating related to the global ocean, with the largest differences in the Pacific and Southern Ocean. Meanwhile, we find a large discrepancy of ocean heat storage in different layers, especially within 300-700 m in the Pacific and Southern Oceans. Furthermore, the near surface analysis of Ishii and IAP are consistent with sea surface temperature (SST) products, but EN4 is found to underestimate the long-term trend. Compared with ocean heat storage derived from the atmospheric budget equation, all products show consistent seasonal cycles of OHC in the upper 1500 m especially during 2008 to 2012. Overall, our analyses further the understanding of the observed OHC variations, and we recommend a careful quantification of errors in the ocean analyses.

Elastodynamic fracture analyses of large crack-arrest experiments

International Nuclear Information System (INIS)

Bass, B.R.; Pugh, C.E.; Walker, J.K.

1985-01-01

Results obtained to date show that the essence of the run-arrest events, including dynamic behavior, is being modeled. Refined meshes and optimum solution algorithms are important parameters in elastodynamic analysis programs to give sufficient resolution to the geometric and time-dependent aspects of fracture analyses. Further refinements in quantitative representation of material parameters and the inclusion of rate dependence through viscoplastic modeling is expected to give an even more accurate basis for assessing the fracture behavior of reactor pressure vessels under PTS and other off-normal loading conditions

Updating signal typing in voice: addition of type 4 signals.

Science.gov (United States)

Sprecher, Alicia; Olszewski, Aleksandra; Jiang, Jack J; Zhang, Yu

2010-06-01

The addition of a fourth type of voice to Titze's voice classification scheme is proposed. This fourth voice type is characterized by primarily stochastic noise behavior and is therefore unsuitable for both perturbation and correlation dimension analysis. Forty voice samples were classified into the proposed four types using narrowband spectrograms. Acoustic, perceptual, and correlation dimension analyses were completed for all voice samples. Perturbation measures tended to increase with voice type. Based on reliability cutoffs, the type 1 and type 2 voices were considered suitable for perturbation analysis. Measures of unreliability were higher for type 3 and 4 voices. Correlation dimension analyses increased significantly with signal type as indicated by a one-way analysis of variance. Notably, correlation dimension analysis could not quantify the type 4 voices. The proposed fourth voice type represents a subset of voices dominated by noise behavior. Current measures capable of evaluating type 4 voices provide only qualitative data (spectrograms, perceptual analysis, and an infinite correlation dimension). Type 4 voices are highly complex and the development of objective measures capable of analyzing these voices remains a topic of future investigation.

ATHENA/INTRA analyses for ITER, NSSR-2

International Nuclear Information System (INIS)

Shen, Kecheng; Eriksson, John; Sjoeberg, A.

1999-02-01

The present report is a summary report including thermal-hydraulic analyses made at Studsvik Eco and Safety AB for the ITER NSSR-2 safety documentation. The objective of the analyses was to reveal the safety characteristics of various heat transfer systems at specified operating conditions and to indicate the conditions for which there were obvious risks of jeopardising the structural integrity of the coolant systems. In the latter case also some analyses were made to indicate conceivable mitigating measures for maintaining the integrity.The analyses were primarily concerned with the First Wall and Divertor heat transfer systems. Several enveloping transients were analysed with associated specific flow and heat load boundary conditions. The analyses were performed with the ATHENA and INTRA codes

ATHENA/INTRA analyses for ITER, NSSR-2

Energy Technology Data Exchange (ETDEWEB)

Shen, Kecheng; Eriksson, John; Sjoeberg, A

1999-02-01

The present report is a summary report including thermal-hydraulic analyses made at Studsvik Eco and Safety AB for the ITER NSSR-2 safety documentation. The objective of the analyses was to reveal the safety characteristics of various heat transfer systems at specified operating conditions and to indicate the conditions for which there were obvious risks of jeopardising the structural integrity of the coolant systems. In the latter case also some analyses were made to indicate conceivable mitigating measures for maintaining the integrity.The analyses were primarily concerned with the First Wall and Divertor heat transfer systems. Several enveloping transients were analysed with associated specific flow and heat load boundary conditions. The analyses were performed with the ATHENA and INTRA codes 8 refs, 14 figs, 15 tabs

Embodied energy and emergy analyses of a concentrating solar power (CSP) system

International Nuclear Information System (INIS)

Zhang Meimei; Wang Zhifeng; Xu Chao; Jiang Hui

2012-01-01

Although concentrating solar power (CSP) technology has been projected as one of the most promising candidates to replace conventional power plants burning fossil fuels, the potential advantages and disadvantages of the CSP technology have not been thoroughly evaluated. To better understand the performance of the CSP technology, this paper presents an ecological accounting framework based on embodied energy and emergy analyses methods. The analyses are performed for the 1.5 MW Dahan solar tower power plant in Beijing, China and different evaluation indices used in the embodied energy and emergy analyses are employed to evaluate the plant performance. Our analysis of the CSP plant are compared with six Italian power plants with different energy sources and an American PV plant, which demonstrates the CSP is the superior technology. - Highlights: ► Embodied energy and emergy analyses are employed to evaluate the first solar tower power plant in China. ► Different evaluation indices are quantitatively analyzed to show the advantages of CSP technology. ► This analysis provides insights for making energy policy and investment decisions about CSP technology.

Comprehensive immunoproteogenomic analyses of malignant pleural mesothelioma.

Science.gov (United States)

Lee, Hyun-Sung; Jang, Hee-Jin; Choi, Jong Min; Zhang, Jun; de Rosen, Veronica Lenge; Wheeler, Thomas M; Lee, Ju-Seog; Tu, Thuydung; Jindra, Peter T; Kerman, Ronald H; Jung, Sung Yun; Kheradmand, Farrah; Sugarbaker, David J; Burt, Bryan M

2018-04-05

We generated a comprehensive atlas of the immunologic cellular networks within human malignant pleural mesothelioma (MPM) using mass cytometry. Data-driven analyses of these high-resolution single-cell data identified 2 distinct immunologic subtypes of MPM with vastly different cellular composition, activation states, and immunologic function; mass spectrometry demonstrated differential abundance of MHC-I and -II neopeptides directly identified between these subtypes. The clinical relevance of this immunologic subtyping was investigated with a discriminatory molecular signature derived through comparison of the proteomes and transcriptomes of these 2 immunologic MPM subtypes. This molecular signature, representative of a favorable intratumoral cell network, was independently associated with improved survival in MPM and predicted response to immune checkpoint inhibitors in patients with MPM and melanoma. These data additionally suggest a potentially novel mechanism of response to checkpoint blockade: requirement for high measured abundance of neopeptides in the presence of high expression of MHC proteins specific for these neopeptides.

Distribution of sulphur and trace elements in peat. [Literature survey with some additional sulphur analyses

Energy Technology Data Exchange (ETDEWEB)

Huttunen, S; Karhu, M

1981-01-01

A survey on the literature and contemporary research was made on peat sulphur and trace element studies. Marked variance between different peatlands and peat types has been noted. The available information is still inadequate for generalizations or statistical analysis mainly due to methodological variations and temporal and spatial variations in results. At the moment, the criteria applied in peatland inventories and evaluations are inadequate with respect to peat quality determinations. To some extent the quality of fuel peat should be determined in a mire inventory prior to peatland utilization. The areas over sulphide clay and some sulphate depositions may considerably increase the peat sulphur content. A proposal has been made to include the sulphur content monitoring in the cases where it exceeds 0.3 per cent. The trace elements may also bring about an increase in peat emissions if the deepest peat layers or polluted layers are burnt. The most important elements in this respect are Al, Fe, Mn, Pb, Zn, V, Ni, Hg, Cu, Cr, as well as As and U. The first ten because of the relatively high concentrations and last two because of pollution or toxocity and ore deposit factors. The peat hydrogen ion concentration has a positive correlation with copper and vanadium. The correlation is positive with the cobalt and nickel contents when the pH is low, and negative at a higher pH. A general peat type correlation shows maximum trace element contents in basal Carex peats with subsoil effects. The peat ash content and the Ti, Pb, V, Cr, Ni and S contents have positive correlations.

Partial-wave analyses of hadron scattering below 2 GeV

International Nuclear Information System (INIS)

Arndt, R.A.; Roper, L.D.

1991-01-01

The Center for Analysis of Particle Scattering (CAPS) in the Department of Physics at Virginia Polytechnic Institute and State University has analyzed basic two-body hadron reactions below 2 GeV for the last two decades. Reactions studied were nucleon-nucleon, pion-nucleon, K + -nucleon and pion photoproduction systems. In addition to analyses of these systems, a computer graphics system (SAID) has been developed and disseminated to over 250 research institutions using VAX computers. The computer-interactive system for disseminating information on basic scattering reactions is also accessible to the physics community through TELNET on the VPI ampersand SU physics department VAX. 6 refs

Herbarium specimens show contrasting phenological responses to Himalayan climate.

Science.gov (United States)

Hart, Robbie; Salick, Jan; Ranjitkar, Sailesh; Xu, Jianchu

2014-07-22

Responses by flowering plants to climate change are complex and only beginning to be understood. Through analyses of 10,295 herbarium specimens of Himalayan Rhododendron collected by plant hunters and botanists since 1884, we were able to separate these responses into significant components. We found a lack of directional change in mean flowering time over the past 45 y of rapid warming. However, over the full 125 y of collections, mean flowering time shows a significant response to year-to-year changes in temperature, and this response varies with season of warming. Mean flowering advances with annual warming (2.27 d earlier per 1 °C warming), and also is delayed with fall warming (2.54 d later per 1 °C warming). Annual warming may advance flowering through positive effects on overwintering bud formation, whereas fall warming may delay flowering through an impact on chilling requirements. The lack of a directional response suggests that contrasting phenological responses to temperature changes may obscure temperature sensitivity in plants. By drawing on large collections from multiple herbaria, made over more than a century, we show how these data may inform studies even of remote localities, and we highlight the increasing value of these and other natural history collections in understanding long-term change.

Cost-effectiveness analysis of additional bevacizumab to pemetrexed plus cisplatin for malignant pleural mesothelioma based on the MAPS trial.

Science.gov (United States)

Zhan, Mei; Zheng, Hanrui; Xu, Ting; Yang, Yu; Li, Qiu

2017-08-01

Malignant pleural mesothelioma (MPM) is a rare malignancy, and pemetrexed/cisplatin (PC) is the gold standard first-line regime. This study evaluated the cost-effectiveness of the addition of bevacizumab to PC (with maintenance bevacizumab) for unresectable MPM based on a phase III trial that showed a survival benefit compared with chemotherapy alone. To estimate the incremental cost-effectiveness ratio (ICER) of the incorporation of bevacizumab, a Markov model based on the MAPS trial, including the disease states of progression-free survival, progressive disease and death, was used. Total costs were calculated from a Chinese payer perspective, and health outcomes were converted into quality-adjusted life year (QALY). Model robustness was explored in sensitivity analyses. The addition of bevacizumab to PC was estimated to increase the cost by $81446.69, with a gain of 0.112 QALYs, resulting in an ICER of $727202.589 per QALY. In both one-way sensitivity and probabilistic sensitivity analyses, the ICER exceeded the commonly accepted willingness-to-pay threshold of 3 times the gross domestic product per capita of China ($23970.00 per QALY). The cost of bevacizumab had the most important impact on the ICER. The combination of bevacizumab with PC chemotherapy is not a cost-effective treatment option for MPM in China. Given its positive clinical value and extremely low incidence of MPM, an appropriate price discount, assistance programs and medical insurance should be considered to make bevacizumab more affordable for this rare patient population. Copyright © 2017 Elsevier B.V. All rights reserved.

Early Versus Delayed Motion After Rotator Cuff Repair: A Systematic Review of Overlapping Meta-analyses.

Science.gov (United States)

Houck, Darby A; Kraeutler, Matthew J; Schuette, Hayden B; McCarty, Eric C; Bravman, Jonathan T

2017-10-01

Previous meta-analyses have been conducted to compare outcomes of early versus delayed motion after rotator cuff repair. To conduct a systematic review of overlapping meta-analyses comparing early versus delayed motion rehabilitation protocols after rotator cuff repair to determine which meta-analyses provide the best available evidence. Systematic review. A systematic review was performed by searching PubMed and Cochrane Library databases. Search terms included "rotator cuff repair," "early passive motion," "immobilization," "rehabilitation protocol," and "meta-analysis." Results were reviewed to determine study eligibility. Patient outcomes and structural healing were extracted from these meta-analyses. Meta-analysis quality was assessed using the Oxman-Guyatt and Quality of Reporting of Meta-analyses (QUOROM) systems. The Jadad decision algorithm was then used to determine which meta-analyses provided the best level of evidence. Seven meta-analyses containing a total of 5896 patients met the eligibility criteria (1 Level I evidence, 4 Level II evidence, 2 Level III evidence). None of these meta-analyses found immobilization to be superior to early motion; however, most studies suggested that early motion would increase range of motion (ROM), thereby reducing time of recovery. Three of these studies suggested that tear size contributed to the choice of rehabilitation to ensure proper healing of the shoulder. A study by Chan et al in 2014 received the highest QUOROM and Oxman-Guyatt scores, and therefore this meta-analysis appeared to have the highest level of evidence. Additionally, a study by Riboh and Garrigues in 2014 was selected as the highest quality study in this systematic review according to the Jadad decision algorithm. The current, best available evidence suggests that early motion improves ROM after rotator cuff repair but increases the risk of rotator cuff retear. Lower quality meta-analyses indicate that tear size may provide a better strategy in

Sensitivity Study of Poisson's Ratio Used in Soil Structure Interaction (SSI) Analyses

International Nuclear Information System (INIS)

Han, Seung-ju; You, Dong-Hyun; Jang, Jung-bum; Yun, Kwan-hee

2016-01-01

The preliminary review for Design Certification (DC) of APR1400 was accepted by NRC on March 4, 2015. After the acceptance of the application for standard DC of APR1400, KHNP has responded the Request for Additional Information (RAI) raised by NRC to undertake a full design certification review. Design certification is achieved through the NRC's rulemaking process, and is founded on the staff's review of the application, which addresses the various safety issues associated with the proposed nuclear power plant design, independent of a specific site. The USNRC issued RAIs pertain to Design Control Document (DCD) Ch.3.7 'Seismic Design' is DCD Tables 3.7A-1 and 3.7A-2 show Poisson’s ratios in the S1 and S2 soil profiles used for SSI analysis as great as 0.47 and 0.48 respectively. Based on staff experience, use of Poisson's ratio approaching these values may result in numerical instability of the SSI analysis results. Sensitivity study is performed using the ACS SASSI NI model of APR1400 with S1 and S2 soil profiles to demonstrate that the Poisson’s ratio values used in the SSI analyses of S1 and S2 soil profile cases do not produce numerical instabilities in the SSI analysis results. No abrupt changes or spurious peaks, which tend to indicate existence of numerical sensitivities in the SASSI solutions, appear in the computed transfer functions of the original SSI analyses that have the maximum dynamic Poisson’s ratio values of 0.47 and 0.48 as well as in the re-computed transfer functions that have the maximum dynamic Poisson’s ratio values limited to 0.42 and 0.45

Additive derivations on algebras of measurable operators

International Nuclear Information System (INIS)

Ayupov, Sh.A.; Kudaybergenov, K.K.

2009-08-01

Given a von Neumann algebra M we introduce the so-called central extension mix(M) of M. We show that mix(M) is a *-subalgebra in the algebra LS(M) of all locally measurable operators with respect to M, and this algebra coincides with LS(M) if and only if M does not admit type II direct summands. We prove that if M is a properly infinite von Neumann algebra then every additive derivation on the algebra mix(M) is inner. This implies that on the algebra LS(M), where M is a type I ∞ or a type III von Neumann algebra, all additive derivations are inner derivations. (author)

Physiological and enzymatic analyses of pineapple subjected to ionizing radiation

International Nuclear Information System (INIS)

Silva, Josenilda Maria da; Silva, Juliana Pizarro; Spoto, Marta Helena Fillet

2007-01-01

The physiological and enzymatic post-harvest characteristics of the pineapple cultivar Smooth Cayenne were evaluated after the fruits were gamma-irradiated with doses of 100 and 150 Gy and the fruits were stored for 10, 20 and 30 days at 12 deg C (±1) and relative humidity of 85% (±5). Physiological and enzymatic analyses were made for each storage period to evaluate the alterations resulting from the application of ionizing radiation. Control specimens showed higher values of soluble pectins, total pectins, reducing sugars, sucrose and total sugars and lower values of polyphenyloxidase and polygalacturonase enzyme activities. All the analyses indicated that storage time is a significantly influencing factor. The 100 Gy dosage and 20-day storage period presented the best results from the standpoint of maturation and conservation of the fruits quality. (author)

Advanced handbook for accident analyses of German nuclear power plants; Weiterentwicklung eines Handbuches fuer Stoerfallanalysen deutscher Kernkraftwerke

Energy Technology Data Exchange (ETDEWEB)

Kerner, Alexander; Broecker, Annette; Hartung, Juergen; Mayer, Gerhard; Pallas Moner, Guim

2014-09-15

The advanced handbook of safety analyses (HSA) comprises a comprehensive electronic collection of knowledge for the compilation and conduction of safety analyses in the area of reactor, plant and containment behaviour as well as results of existing safety analyses (performed by GRS in the past) with characteristic specifications and further background information. In addition, know-how from the analysis software development and validation process is presented and relevant rules and regulations with regard to safety demonstration are provided. The HSA comprehensively covers the topic thermo-hydraulic safety analyses (except natural hazards, man-made hazards and malicious acts) for German pressurized and boiling water reactors for power and non-power operational states. In principle, the structure of the HSA-content represents the analytical approach utilized by safety analyses and applying the knowledge from safety analyses to technical support services. On the basis of a multilevel preparation of information to the topics ''compilation of safety analyses'', ''compilation of data bases'', ''assessment of safety analyses'', ''performed safety analyses'', ''rules and regulation'' and ''ATHLET-validation'' the HSA addresses users with different background, allowing them to enter the HSA at different levels. Moreover, the HSA serves as a reference book, which is designed future-oriented, freely configurable related to the content, completely integrated into the GRS internal portal and prepared to be used by a growing user group.

Electron microprobe analyses of glasses from Kīlauea tephra units, Kīlauea Volcano, Hawaii

Science.gov (United States)

Helz, Rosalind L.; Clague, David A.; Mastin, Larry G.; Rose, Timothy R.

2014-01-01

This report presents approximately 2,100 glass analyses from three tephra units of Kīlauea Volcano: the Keanakākoʻi Tephra, the Kulanaokuaiki Tephra, and the Pāhala Ash. It also includes some new analyses obtained as part of a re-evaluation of the MgO contents of glasses in two of the three original datasets; this re-evaluation was conducted to improve the consistency of glass MgO contents among the three datasets. The glass data are a principal focus of Helz and others (in press), which will appear in the AGU Monograph Hawaiian Volcanoes—From Source to Surface. The report is intended to support this publication, in addition to making the data available to the scientific community.

Improving Performance of Software Implemented Floating Point Addition

DEFF Research Database (Denmark)

Hindborg, Andreas Erik; Karlsson, Sven

2011-01-01

We outline and evaluate hardware extensions to an integer processor pipeline which allow IEEE 754 oating point, FP, addition to be eciently implemented in software. With a very moderate increase in hardware resources, our perfor- mance evaluation shows that, for a benchmark that executes 12.5% FP...... addition instructions, our approach exhibits a rel- ative slowdown of 3.38 to 15.15 as compared to dedicated hardware. This is a signicant improvement of pure software emulation which leads to relative slowdowns up to 45.33....

Effectiveness and cost-effectiveness of ehealth interventions in somatic diseases: a systematic review of systematic reviews and meta-analyses.

Science.gov (United States)

Elbert, Niels J; van Os-Medendorp, Harmieke; van Renselaar, Wilco; Ekeland, Anne G; Hakkaart-van Roijen, Leona; Raat, Hein; Nijsten, Tamar E C; Pasmans, Suzanne G M A

2014-04-16

eHealth potentially enhances quality of care and may reduce health care costs. However, a review of systematic reviews published in 2010 concluded that high-quality evidence on the benefits of eHealth interventions was still lacking. We conducted a systematic review of systematic reviews and meta-analyses on the effectiveness/cost-effectiveness of eHealth interventions in patients with somatic diseases to analyze whether, and to what possible extent, the outcome of recent research supports or differs from previous conclusions. Literature searches were performed in PubMed, EMBASE, The Cochrane Library, and Scopus for systematic reviews and meta-analyses on eHealth interventions published between August 2009 and December 2012. Articles were screened for relevance based on preset inclusion and exclusion criteria. Citations of residual articles were screened for additional literature. Included papers were critically appraised using the Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA) Statement before data were extracted. Based on conclusions drawn by the authors of the included articles, reviews and meta-analyses were divided into 1 of 3 groups: suitable, promising, or limited evidence on effectiveness/cost-effectiveness. Cases of uncertainty were resolved by consensus discussion. Effect sizes were extracted from papers that included a meta-analysis. To compare our results with previous findings, a trend analysis was performed. Our literature searches yielded 31 eligible reviews, of which 20 (65%) reported on costs. Seven papers (23%) concluded that eHealth is effective/cost-effective, 13 (42%) underlined that evidence is promising, and others found limited or inconsistent proof. Methodological quality of the included reviews and meta-analyses was generally considered high. Trend analysis showed a considerable accumulation of literature on eHealth. However, a similar percentage of papers concluded that eHealth is effective/cost-effective or

Multielemental analyses of tree rings by inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Hall, G.S.

1990-01-01

Inductively coupled plasma mass spectrometry (ICP-MS) was evaluated for major, minor, trace, and ultra-trace elemental analyses of individual tree rings. The samples were obtained from an old-growth Douglas fir growing near Mount St. Helens volcano, and from trees at various other North American sites. Eightly percent of elements from Li to U had detection limits in the solid (wood) below 8.0 ng g -1 . Two anomalous peaks occur in Mount St. Helens samples at A.D. 1478 and 1490 that closely correlate with past eruptions of the volcano. These results show that ICP-MS is a rapid and sensitive analytical method for multielemental analyses of individual tree rings. (author) 16 refs.; 2 figs.; 2 tabs

Genome-wide analyses reveal a role for peptide hormones in planarian germline development.

Directory of Open Access Journals (Sweden)

James J Collins

Full Text Available Bioactive peptides (i.e., neuropeptides or peptide hormones represent the largest class of cell-cell signaling molecules in metazoans and are potent regulators of neural and physiological function. In vertebrates, peptide hormones play an integral role in endocrine signaling between the brain and the gonads that controls reproductive development, yet few of these molecules have been shown to influence reproductive development in invertebrates. Here, we define a role for peptide hormones in controlling reproductive physiology of the model flatworm, the planarian Schmidtea mediterranea. Based on our observation that defective neuropeptide processing results in defects in reproductive system development, we employed peptidomic and functional genomic approaches to characterize the planarian peptide hormone complement, identifying 51 prohormone genes and validating 142 peptides biochemically. Comprehensive in situ hybridization analyses of prohormone gene expression revealed the unanticipated complexity of the flatworm nervous system and identified a prohormone specifically expressed in the nervous system of sexually reproducing planarians. We show that this member of the neuropeptide Y superfamily is required for the maintenance of mature reproductive organs and differentiated germ cells in the testes. Additionally, comparative analyses of our biochemically validated prohormones with the genomes of the parasitic flatworms Schistosoma mansoni and Schistosoma japonicum identified new schistosome prohormones and validated half of all predicted peptide-encoding genes in these parasites. These studies describe the peptide hormone complement of a flatworm on a genome-wide scale and reveal a previously uncharacterized role for peptide hormones in flatworm reproduction. Furthermore, they suggest new opportunities for using planarians as free-living models for understanding the reproductive biology of flatworm parasites.

Thermoelastic analyses of spent fuel repositories in bedded and dome salt. Technical memorandum report RSI-0054

International Nuclear Information System (INIS)

Callahan, G.D.; Ratigan, J.L.

1978-01-01

Global thermoelastic analyses of bedded and dome salt models showed a slight preference for the bedded salt model through the range of thermal loading conditions. Spent fuel thermal loadings should be less than 75 kW/acre of the repository pending more accurate material modeling. One should first limit the study to one or two spent fuel thermal loading (i.e. 75 kW/acre and/or 50 kW/acre) analyses up to a maximum time of approximately 2000 years. Parametric thermoelastic type analyses could then be readily obtained to determine the influence of the thermomechanical properties. Recommendations for further study include parametric analyses, plasticity analyses, consideration of the material interfaces as joints, and possibly consideration of a global joint pattern (i.e. jointed at the same orientation everywhere) for the non-salt materials. Subsequently, the viscoelastic analyses could be performed

Rapid and recent diversification patterns in Anseriformes birds: Inferred from molecular phylogeny and diversification analyses.

Science.gov (United States)

Sun, Zhonglou; Pan, Tao; Hu, Chaochao; Sun, Lu; Ding, Hengwu; Wang, Hui; Zhang, Chenling; Jin, Hong; Chang, Qing; Kan, Xianzhao; Zhang, Baowei

2017-01-01

The Anseriformes is a well-known and widely distributed bird order, with more than 150 species in the world. This paper aims to revise the classification, determine the phylogenetic relationships and diversification patterns in Anseriformes by exploring the Cyt b, ND2, COI genes and the complete mitochondrial genomes (mito-genomes). Molecular phylogeny and genetic distance analyses suggest that the Dendrocygna species should be considered as an independent family, Dendrocygnidae, rather than a member of Anatidae. Molecular timescale analyses suggests that the ancestral diversification occurred during the Early Eocene Climatic Optimum (58 ~ 50 Ma). Furthermore, diversification analyses showed that, after a long period of constant diversification, the median initial speciation rate was accelerated three times, and finally increased to approximately 0.3 sp/My. In the present study, both molecular phylogeny and diversification analyses results support that Anseriformes birds underwent rapid and recent diversification in their evolutionary history, especially in modern ducks, which show extreme diversification during the Plio-Pleistocene (~ 5.3 Ma). Therefore, our study support that the Plio-Pleistocene climate fluctuations are likely to have played a significant role in promoting the recent diversification for Anseriformes.

Rapid and recent diversification patterns in Anseriformes birds: Inferred from molecular phylogeny and diversification analyses.

Directory of Open Access Journals (Sweden)

Zhonglou Sun

Full Text Available The Anseriformes is a well-known and widely distributed bird order, with more than 150 species in the world. This paper aims to revise the classification, determine the phylogenetic relationships and diversification patterns in Anseriformes by exploring the Cyt b, ND2, COI genes and the complete mitochondrial genomes (mito-genomes. Molecular phylogeny and genetic distance analyses suggest that the Dendrocygna species should be considered as an independent family, Dendrocygnidae, rather than a member of Anatidae. Molecular timescale analyses suggests that the ancestral diversification occurred during the Early Eocene Climatic Optimum (58 ~ 50 Ma. Furthermore, diversification analyses showed that, after a long period of constant diversification, the median initial speciation rate was accelerated three times, and finally increased to approximately 0.3 sp/My. In the present study, both molecular phylogeny and diversification analyses results support that Anseriformes birds underwent rapid and recent diversification in their evolutionary history, especially in modern ducks, which show extreme diversification during the Plio-Pleistocene (~ 5.3 Ma. Therefore, our study support that the Plio-Pleistocene climate fluctuations are likely to have played a significant role in promoting the recent diversification for Anseriformes.

Effect of the Prodegradant-Additive Plastics Incorporated on the Polyethylene Recycling

Directory of Open Access Journals (Sweden)

Miguel Aldas

2018-01-01

Full Text Available The effect of degraded plastic with prodegradants on the polyethylene properties was studied. First, the mixture of low-density polyethylene (LDPE with 5 wt.% prodegradant (oxo-degradable additive was prepared by melt processing using a mixer chamber. Then, the degradation of the mixtures was evaluated by exposing the oxo-degradable LDPE in a Xenon arc chamber for 300 hours. The degraded material was characterized by infrared spectroscopy (FTIR assessing the carbonyl index and the hydroperoxide band. Then, different percentages of degraded material (1, 5, 10, 20, and 50 wt.% were incorporated into the neat LDPE. Mechanical and rheological tests were carried out to evaluate the recycling process of these blends. Also, the feasibility of the blends reprocessing was determined by analysing the melt flow index for each heating process and shear stress applied. It was evidenced that the increment of the content of the degraded material in the neat LDPE decreased the mechanical strength and the processability of blends due to the imminent thermal degradation. All the test results showed that the incorporation of degraded material causes a considerable reduction in the matrix properties during the reprocessing. Nevertheless, at low concentrations, the properties of the oxo-degradable LDPE–LDPE blends were found to be similar to the neat LDPE.

Genetic and epigenetic variations induced by wheat-rye 2R and 5R monosomic addition lines.

Directory of Open Access Journals (Sweden)

Shulan Fu

Full Text Available BACKGROUND: Monosomic alien addition lines (MAALs can easily induce structural variation of chromosomes and have been used in crop breeding; however, it is unclear whether MAALs will induce drastic genetic and epigenetic alterations. METHODOLOGY/PRINCIPAL FINDINGS: In the present study, wheat-rye 2R and 5R MAALs together with their selfed progeny and parental common wheat were investigated through amplified fragment length polymorphism (AFLP and methylation-sensitive amplification polymorphism (MSAP analyses. The MAALs in different generations displayed different genetic variations. Some progeny that only contained 42 wheat chromosomes showed great genetic/epigenetic alterations. Cryptic rye chromatin has introgressed into the wheat genome. However, one of the progeny that contained cryptic rye chromatin did not display outstanding genetic/epigenetic variation. 78 and 49 sequences were cloned from changed AFLP and MSAP bands, respectively. Blastn search indicated that almost half of them showed no significant similarity to known sequences. Retrotransposons were mainly involved in genetic and epigenetic variations. Genetic variations basically affected Gypsy-like retrotransposons, whereas epigenetic alterations affected Copia-like and Gypsy-like retrotransposons equally. Genetic and epigenetic variations seldom affected low-copy coding DNA sequences. CONCLUSIONS/SIGNIFICANCE: The results in the present study provided direct evidence to illustrate that monosomic wheat-rye addition lines could induce different and drastic genetic/epigenetic variations and these variations might not be caused by introgression of rye chromatins into wheat. Therefore, MAALs may be directly used as an effective means to broaden the genetic diversity of common wheat.

Cost-benefit analyses of supplementary measles immunisation in the highly immunized population of New Zealand.

Science.gov (United States)

Hayman, D T S; Marshall, J C; French, N P; Carpenter, T E; Roberts, M G; Kiedrzynski, T

2017-09-05

As endemic measles is eliminated from countries through increased immunisation, the economic benefits of enhanced immunisation programs may come into question. New Zealand has suffered from outbreaks after measles introductions from abroad and we use it as a model system to understand the benefits of catch up immunisation in highly immunised populations. We provide cost-benefit analyses for measles supplementary immunisation in New Zealand. We model outbreaks based on estimates of the basic reproduction number in the vaccinated population (R v , the number of secondary infections in a partially immunised population), based on the number of immunologically-naïve people at district and national levels, considering both pre- and post-catch up vaccination scenarios. Our analyses suggest that measles R v often includes or exceeds one (0.18-3.92) despite high levels of population immunity. We calculate the cost of the first 187 confirmed and probable measles cases in 2014 to be over NZ$1 million (∼US$864,200) due to earnings lost, case management and hospitalization costs. The benefit-cost ratio analyses suggest additional vaccination beyond routine childhood immunisation is economically efficient. Supplemental vaccination-related costs are required to exceed approximately US$66 to US$1877 per person, depending on different scenarios, before supplemental vaccination is economically inefficient. Thus, our analysis suggests additional immunisation beyond childhood programs to target naïve individuals is economically beneficial even when childhood immunisation rates are high. Copyright © 2017 Elsevier Ltd. All rights reserved.

Enhanced flux pinning in MOCVD-YBCO films through Zr additions: systematic feasibility studies

International Nuclear Information System (INIS)

Aytug, T; Paranthaman, M; Specht, E D; Zhang, Y; Kim, K; Zuev, Y L; Cantoni, C; Goyal, A; Christen, D K; Maroni, V A; Chen, Y; Selvamanickam, V

2010-01-01

Systematic effects of Zr additions on the structural and flux pinning properties of YBa 2 Cu 3 O 7-δ (YBCO) films deposited by metal-organic chemical vapor deposition (MOCVD) have been investigated. Detailed characterization, conducted by coordinated transport, x-ray diffraction, scanning and transmission electron microscopy analyses, and imaging Raman microscopy have revealed trends in the resulting property/performance correlations of these films with respect to varying mole percentages (mol%) of added Zr. For compositions ≤7.5 mol%, Zr additions lead to improved in-field critical current density, as well as extra correlated pinning along the c-axis direction of the YBCO films via the formation of columnar, self-assembled stacks of BaZrO 3 nanodots.

Additive manufacturing.

Science.gov (United States)

Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

2018-04-01

Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

Biomass feedstock analyses

Energy Technology Data Exchange (ETDEWEB)

Wilen, C.; Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

1996-12-31

The overall objectives of the project `Feasibility of electricity production from biomass by pressurized gasification systems` within the EC Research Programme JOULE II were to evaluate the potential of advanced power production systems based on biomass gasification and to study the technical and economic feasibility of these new processes with different type of biomass feed stocks. This report was prepared as part of this R and D project. The objectives of this task were to perform fuel analyses of potential woody and herbaceous biomasses with specific regard to the gasification properties of the selected feed stocks. The analyses of 15 Scandinavian and European biomass feed stock included density, proximate and ultimate analyses, trace compounds, ash composition and fusion behaviour in oxidizing and reducing atmospheres. The wood-derived fuels, such as whole-tree chips, forest residues, bark and to some extent willow, can be expected to have good gasification properties. Difficulties caused by ash fusion and sintering in straw combustion and gasification are generally known. The ash and alkali metal contents of the European biomasses harvested in Italy resembled those of the Nordic straws, and it is expected that they behave to a great extent as straw in gasification. Any direct relation between the ash fusion behavior (determined according to the standard method) and, for instance, the alkali metal content was not found in the laboratory determinations. A more profound characterisation of the fuels would require gasification experiments in a thermobalance and a PDU (Process development Unit) rig. (orig.) (10 refs.)

Graphical augmentations to the funnel plot assess the impact of additional evidence on a meta-analysis.

Science.gov (United States)

Langan, Dean; Higgins, Julian P T; Gregory, Walter; Sutton, Alexander J

2012-05-01

We aim to illustrate the potential impact of a new study on a meta-analysis, which gives an indication of the robustness of the meta-analysis. A number of augmentations are proposed to one of the most widely used of graphical displays, the funnel plot. Namely, 1) statistical significance contours, which define regions of the funnel plot in which a new study would have to be located to change the statistical significance of the meta-analysis; and 2) heterogeneity contours, which show how a new study would affect the extent of heterogeneity in a given meta-analysis. Several other features are also described, and the use of multiple features simultaneously is considered. The statistical significance contours suggest that one additional study, no matter how large, may have a very limited impact on the statistical significance of a meta-analysis. The heterogeneity contours illustrate that one outlying study can increase the level of heterogeneity dramatically. The additional features of the funnel plot have applications including 1) informing sample size calculations for the design of future studies eligible for inclusion in the meta-analysis; and 2) informing the updating prioritization of a portfolio of meta-analyses such as those prepared by the Cochrane Collaboration. Copyright © 2012 Elsevier Inc. All rights reserved.

Thermal Safety Analyses for the Production of Plutonium-238 at the High Flux Isotope Reactor

Energy Technology Data Exchange (ETDEWEB)

Hurt, Christopher J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Freels, James D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hobbs, Randy W. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jain, Prashant K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Maldonado, G. Ivan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2016-08-01

that were necessary due to the limiting fabrication and irradiation data available. The calculated parameters in the final production target model are the most accurate and comprehensive, while still conservative. Over 210 permutations in irradiation time and position were evaluated, and are supported by the most recent inputs and highest fidelity methodology. The results of these analyses show that the models presented in this report provide a robust and reliable basis for previous, current and future experiment safety analyses. In addition, they reveal an evolving knowledge of the steady-state behavior of the NpO₂/Al pellets under irradiation for a variety of target encapsulations and potential conditions.

Application of additive tariffs in the electricity sector

International Nuclear Information System (INIS)

Apolinario, I.; Felizardo, N.; Leite Garcia, A.; Oliveira, P.; Trindade, A.; Vasconcelos, J.; Verdelho, P.

2004-01-01

This paper presents and discusses a methodology for the calculation and application of tariffs in the electricity sector based on the principle of tariff additivity. It shows how such tariffs can reflect costs and assure the absence of cross subsidies between clients. The methodology presented was adopted in the Portuguese Tariff Code for electricity by the Portuguese Energy Regulator (ERSE). The work presented in this article reflects the experience acquired by ERSE during the preparation, discussion and implementation of that Code. Allowed revenues are determined separately for every regulated activity, assuring that there are no cross subsidies between activities. Additionally, the application of the tariff additivity principle assures the nonexistence of cross subsidies between consumers. Regulated tariffs applicable to end users of electricity are determined by summation, variable by variable, of the different activity tariffs in accordance with the services the costumer uses and in the proportion of that use. The corollary is that if the different activity tariffs are cost reflective and promote efficiency in resource allocation, the tariffs applicable to consumers (access tariffs or integral tariffs) will also reflect costs in the same manner. Therefore, besides economic efficiency, equity between non binding system consumers and binding system consumers is promoted. The examples presented in the article intend to show how additive tariffs reflect costs giving adequate economic price signals for the rational use of the networks and electric energy consumption

COCAP: a carbon dioxide analyser for small unmanned aircraft systems

Science.gov (United States)

Kunz, Martin; Lavric, Jost V.; Gerbig, Christoph; Tans, Pieter; Neff, Don; Hummelgård, Christine; Martin, Hans; Rödjegård, Henrik; Wrenger, Burkhard; Heimann, Martin

2018-03-01

Unmanned aircraft systems (UASs) could provide a cost-effective way to close gaps in the observation of the carbon cycle, provided that small yet accurate analysers are available. We have developed a COmpact Carbon dioxide analyser for Airborne Platforms (COCAP). The accuracy of COCAP's carbon dioxide (CO2) measurements is ensured by calibration in an environmental chamber, regular calibration in the field and by chemical drying of sampled air. In addition, the package contains a lightweight thermal stabilisation system that reduces the influence of ambient temperature changes on the CO2 sensor by 2 orders of magnitude. During validation of COCAP's CO2 measurements in simulated and real flights we found a measurement error of 1.2 µmol mol-1 or better with no indication of bias. COCAP is a self-contained package that has proven well suited for the operation on board small UASs. Besides carbon dioxide dry air mole fraction it also measures air temperature, humidity and pressure. We describe the measurement system and our calibration strategy in detail to support others in tapping the potential of UASs for atmospheric trace gas measurements.

Analyser Framework to Verify Software Components

Directory of Open Access Journals (Sweden)

Rolf Andreas Rasenack

2009-01-01

Full Text Available Today, it is important for software companies to build software systems in a short time-interval, to reduce costs and to have a good market position. Therefore well organized and systematic development approaches are required. Reusing software components, which are well tested, can be a good solution to develop software applications in effective manner. The reuse of software components is less expensive and less time consuming than a development from scratch. But it is dangerous to think that software components can be match together without any problems. Software components itself are well tested, of course, but even if they composed together problems occur. Most problems are based on interaction respectively communication. Avoiding such errors a framework has to be developed for analysing software components. That framework determines the compatibility of corresponding software components. The promising approach discussed here, presents a novel technique for analysing software components by applying an Abstract Syntax Language Tree (ASLT. A supportive environment will be designed that checks the compatibility of black-box software components. This article is concerned to the question how can be coupled software components verified by using an analyzer framework and determines the usage of the ASLT. Black-box Software Components and Abstract Syntax Language Tree are the basis for developing the proposed framework and are discussed here to provide the background knowledge. The practical implementation of this framework is discussed and shows the result by using a test environment.

Transfer of Training in Simple Addition.

Science.gov (United States)

Chen, Yalin; Campbell, Jamie I D

2017-04-18

In recent years several researchers have proposed that skilled adults may solve single-digit addition problems (e.g. 3 + 1 = 4, 4 + 3 = 7) using a fast counting procedure. Practicing a procedure, often leads to transfer of learning and faster performance of unpracticed items. Such transfer has been demonstrated using a counting-based alphabet arithmetic task (e.g., B + 4 = C D E F) that indicated robust generalization of practice (i.e., RT gains) when untrained transfer problems at test had been implicitly practiced (e.g., practice B + 3, test B + 2 or B + 1). Here we constructed analogous simple addition problems (practice 4 + 3, test 4 + 2 or 4 + 1). In each of three experiments (total n = 108) participants received six practice blocks followed by two test blocks of new problems to examine generalization effects. Practice of addition identity-rule problems (i.e., 0 + N = N) showed complete transfer of RT gains made during practice to unpracticed items at test. In contrast, the addition ties (2 + 2, 3 + 3, etc.) presented large RT costs for unpracticed problems at test, but sped up substantially in the second test block. This pattern is consistent with item-specific strengthening of associative memory. The critical items were small non-tie additions (sum ≤ 10) for which the test problems would be implicitly practiced if counting was employed during practice. In all three experiments (and collectively) there was no evidence of generalization for these items in the first test block, but there was robust speed up when the items were repeated in the second test block. Thus, there was no evidence of the generalization of practice that would be expected if counting procedures mediated our participants' performance on small non-tie addition problems.

Risico-analyse brandstofpontons

NARCIS (Netherlands)

Uijt de Haag P; Post J; LSO

2001-01-01

Voor het bepalen van de risico's van brandstofpontons in een jachthaven is een generieke risico-analyse uitgevoerd. Er is een referentiesysteem gedefinieerd, bestaande uit een betonnen brandstofponton met een relatief grote inhoud en doorzet. Aangenomen is dat de ponton gelegen is in een

Anatomically ordered tapping interferes more with one-digit addition than two-digit addition: a dual-task fMRI study.

Science.gov (United States)

Soylu, Firat; Newman, Sharlene D

2016-02-01

Fingers are used as canonical representations for numbers across cultures. In previous imaging studies, it was shown that arithmetic processing activates neural resources that are known to participate in finger movements. Additionally, in one dual-task study, it was shown that anatomically ordered finger tapping disrupts addition and subtraction more than multiplication, possibly due to a long-lasting effect of early finger counting experiences on the neural correlates and organization of addition and subtraction processes. How arithmetic task difficulty and tapping complexity affect the concurrent performance is still unclear. If early finger counting experiences have bearing on the neural correlates of arithmetic in adults, then one would expect anatomically and non-anatomically ordered tapping to have different interference effects, given that finger counting is usually anatomically ordered. To unravel these issues, we studied how (1) arithmetic task difficulty and (2) the complexity of the finger tapping sequence (anatomical vs. non-anatomical ordering) affect concurrent performance and use of key neural circuits using a mixed block/event-related dual-task fMRI design with adult participants. The results suggest that complexity of the tapping sequence modulates interference on addition, and that one-digit addition (fact retrieval), compared to two-digit addition (calculation), is more affected from anatomically ordered tapping. The region-of-interest analysis showed higher left angular gyrus BOLD response for one-digit compared to two-digit addition, and in no-tapping conditions than dual tapping conditions. The results support a specific association between addition fact retrieval and anatomically ordered finger movements in adults, possibly due to finger counting strategies that deploy anatomically ordered finger movements early in the development.

Immature granulocyte detection by the SE-9000 haematology analyser during pregnancy.

Science.gov (United States)

Fernández-Suárez, A; Pascual, V T; Gimenez, M T F; Hernández, J F S

2003-12-01

The objective of this study was to determine the nature of the alarm for immature granulocytes appearing in haemograms from pregnant women, as detected by the immature cell information channel (IMI) of the SE-9000 automated haematology analyser. Of all tests run on pregnant women in a 4-month period (n = 698), the first 100 haemograms with immature granulocyte alarms (14.33%) were collected. Each of these samples was then stained with Wright-Giemsa stain. The following variables were also analysed: age of the mother, trimester and days of gestation, type of delivery, weight and sex of the baby, and Apgar score. Most pregnant women were in the third trimester of gestation (82%) when an alarm was noted on the IMI channel. Of the patients, 62% had normal deliveries. The most frequent complication was obstructed delivery (23%). Mean percentages by microscopic counts of band cells, metamyelocytes, and myelocytes were 2.99, 0.45, and 0.19%, respectively. There was a statistically significant correlation for all cell types between the SE-9000 and the manual count method. No association was observed between the presence of immature granulocytes and the clinical variables analysed. The SE-9000 analyser shows high sensitivity in the IMI channel for detection of immature forms.

A simplified method for obtaining high-purity perchlorate from groundwater for isotope analyses.

Energy Technology Data Exchange (ETDEWEB)

vonKiparski, G; Hillegonds, D

2011-04-04

Investigations into the occurrence and origin of perchlorate (ClO{sub 4}{sup -}) found in groundwater from across North America have been sparse until recent years, and there is mounting evidence that natural formation mechanisms are important. New opportunities for identifying groundwater perchlorate and its origin have arisen with the utilization of improved detection methods and sampling techniques. Additionally, application of the forensic potential of isotopic measurements has begun to elucidate sources, potential formation mechanisms and natural attenuation processes. Procedures developed appear to be amenable to enable high precision stable isotopic analyses, as well as lower precision AMS analyses of {sup 36}Cl. Immediate work is in analyzing perchlorate isotope standards and developing full analytical accuracy and uncertainty expectations. Field samples have also been collected, and will be analyzed when final qa/qc samples are deemed acceptable.

Preferred Reporting Items for Systematic Review and Meta-Analyses of individual participant data: the PRISMA-IPD Statement.

Science.gov (United States)

Stewart, Lesley A; Clarke, Mike; Rovers, Maroeska; Riley, Richard D; Simmonds, Mark; Stewart, Gavin; Tierney, Jayne F

2015-04-28

Systematic reviews and meta-analyses of individual participant data (IPD) aim to collect, check, and reanalyze individual-level data from all studies addressing a particular research question and are therefore considered a gold standard approach to evidence synthesis. They are likely to be used with increasing frequency as current initiatives to share clinical trial data gain momentum and may be particularly important in reviewing controversial therapeutic areas. To develop PRISMA-IPD as a stand-alone extension to the PRISMA (Preferred Reporting Items for Systematic Reviews and Meta-Analyses) Statement, tailored to the specific requirements of reporting systematic reviews and meta-analyses of IPD. Although developed primarily for reviews of randomized trials, many items will apply in other contexts, including reviews of diagnosis and prognosis. Development of PRISMA-IPD followed the EQUATOR Network framework guidance and used the existing standard PRISMA Statement as a starting point to draft additional relevant material. A web-based survey informed discussion at an international workshop that included researchers, clinicians, methodologists experienced in conducting systematic reviews and meta-analyses of IPD, and journal editors. The statement was drafted and iterative refinements were made by the project, advisory, and development groups. The PRISMA-IPD Development Group reached agreement on the PRISMA-IPD checklist and flow diagram by consensus. Compared with standard PRISMA, the PRISMA-IPD checklist includes 3 new items that address (1) methods of checking the integrity of the IPD (such as pattern of randomization, data consistency, baseline imbalance, and missing data), (2) reporting any important issues that emerge, and (3) exploring variation (such as whether certain types of individual benefit more from the intervention than others). A further additional item was created by reorganization of standard PRISMA items relating to interpreting results. Wording

Identification and Characterisation CRN Effectors in Phytophthora capsici Shows Modularity and Functional Diversity.

Directory of Open Access Journals (Sweden)

Remco Stam

Full Text Available Phytophthora species secrete a large array of effectors during infection of their host plants. The Crinkler (CRN gene family encodes a ubiquitous but understudied class of effectors with possible but as of yet unknown roles in infection. To appreciate CRN effector function in Phytophthora, we devised a simple Crn gene identification and annotation pipeline to improve effector prediction rates. We predicted 84 full-length CRN coding genes and assessed CRN effector domain diversity in sequenced Oomycete genomes. These analyses revealed evidence of CRN domain innovation in Phytophthora and expansion in the Peronosporales. We performed gene expression analyses to validate and define two classes of CRN effectors, each possibly contributing to infection at different stages. CRN localisation studies revealed that P. capsici CRN effector domains target the nucleus and accumulate in specific sub-nuclear compartments. Phenotypic analyses showed that few CRN domains induce necrosis when expressed in planta and that one cell death inducing effector, enhances P. capsici virulence on Nicotiana benthamiana. These results suggest that the CRN protein family form an important class of intracellular effectors that target the host nucleus during infection. These results combined with domain expansion in hemi-biotrophic and necrotrophic pathogens, suggests specific contributions to pathogen lifestyles. This work will bolster CRN identification efforts in other sequenced oomycete species and set the stage for future functional studies towards understanding CRN effector functions.

Stable dispersion of nanodiamonds in oil and their tribological properties as lubricant additives

Science.gov (United States)

Lee, Gyoung-Ja; Park, Jin-Ju; Lee, Min-Ku; Rhee, Chang Kyu

2017-09-01

Nanodiamonds (NDs) are innovative additives when a combination of mechanical, thermal, tribological, and dielectric properties are required. In this study, a surface modification with oleic acid (OA) is developed for the deaggregation and prolonged dispersion of NDs in oil, and the effect of the NDs as lubricant additives on the tribological properties of a steel substrate is investigated. The OA renders the ND surface hydrophobic and decreases the average particle size from 268.6 to 20.1 nm. The OA-treated NDs exhibit very stable dispersion in oil even after more than 10 days, compared with the untreated NDs. From the analyses of the friction coefficient, wear loss, and worn surfaces using a ball-on-disk wear test, it is concluded that a 0.05 wt% addition of OA-treated NDs in oil lubricant provides excellent friction and anti-wear properties with the friction coefficient being reduced by 23%.

Grey literature in meta-analyses.

Science.gov (United States)

Conn, Vicki S; Valentine, Jeffrey C; Cooper, Harris M; Rantz, Marilyn J

2003-01-01

In meta-analysis, researchers combine the results of individual studies to arrive at cumulative conclusions. Meta-analysts sometimes include "grey literature" in their evidential base, which includes unpublished studies and studies published outside widely available journals. Because grey literature is a source of data that might not employ peer review, critics have questioned the validity of its data and the results of meta-analyses that include it. To examine evidence regarding whether grey literature should be included in meta-analyses and strategies to manage grey literature in quantitative synthesis. This article reviews evidence on whether the results of studies published in peer-reviewed journals are representative of results from broader samplings of research on a topic as a rationale for inclusion of grey literature. Strategies to enhance access to grey literature are addressed. The most consistent and robust difference between published and grey literature is that published research is more likely to contain results that are statistically significant. Effect size estimates of published research are about one-third larger than those of unpublished studies. Unfunded and small sample studies are less likely to be published. Yet, importantly, methodological rigor does not differ between published and grey literature. Meta-analyses that exclude grey literature likely (a) over-represent studies with statistically significant findings, (b) inflate effect size estimates, and (c) provide less precise effect size estimates than meta-analyses including grey literature. Meta-analyses should include grey literature to fully reflect the existing evidential base and should assess the impact of methodological variations through moderator analysis.

Genome-wide DNA polymorphism analyses using VariScan

Directory of Open Access Journals (Sweden)

Vilella Albert J

2006-09-01

Full Text Available Abstract Background DNA sequence polymorphisms analysis can provide valuable information on the evolutionary forces shaping nucleotide variation, and provides an insight into the functional significance of genomic regions. The recent ongoing genome projects will radically improve our capabilities to detect specific genomic regions shaped by natural selection. Current available methods and software, however, are unsatisfactory for such genome-wide analysis. Results We have developed methods for the analysis of DNA sequence polymorphisms at the genome-wide scale. These methods, which have been tested on a coalescent-simulated and actual data files from mouse and human, have been implemented in the VariScan software package version 2.0. Additionally, we have also incorporated a graphical-user interface. The main features of this software are: i exhaustive population-genetic analyses including those based on the coalescent theory; ii analysis adapted to the shallow data generated by the high-throughput genome projects; iii use of genome annotations to conduct a comprehensive analyses separately for different functional regions; iv identification of relevant genomic regions by the sliding-window and wavelet-multiresolution approaches; v visualization of the results integrated with current genome annotations in commonly available genome browsers. Conclusion VariScan is a powerful and flexible suite of software for the analysis of DNA polymorphisms. The current version implements new algorithms, methods, and capabilities, providing an important tool for an exhaustive exploratory analysis of genome-wide DNA polymorphism data.

CPR in medical TV shows: non-health care student perspective.

Science.gov (United States)

Alismail, Abdullah; Meyer, Nicole C; Almutairi, Waleed; Daher, Noha S

2018-01-01

There are over a dozen medical shows airing on television, many of which are during prime time. Researchers have recently become more interested in the role of these shows, and the awareness on cardiopulmonary resuscitation. Several cases have been reported where a lay person resuscitated a family member using medical TV shows as a reference. The purpose of this study is to examine and evaluate college students' perception on cardiopulmonary resuscitation and when to shock using an automated external defibrillator based on their experience of watching medical TV shows. A total of 170 students (nonmedical major) were surveyed in four different colleges in the United States. The survey consisted of questions that reflect their perception and knowledge acquired from watching medical TV shows. A stepwise regression was used to determine the significant predictors of "How often do you watch medical drama TV shows" in addition to chi-square analysis for nominal variables. Regression model showed significant effect that TV shows did change students' perception positively ( p <0.001), and they would select shock on asystole as the frequency of watching increases ( p =0.023). The findings of this study show that high percentage of nonmedical college students are influenced significantly by medical shows. One particular influence is the false belief about when a shock using the automated external defibrillator (AED) is appropriate as it is portrayed falsely in most medical shows. This finding raises a concern about how these shows portray basic life support, especially when not following American Heart Association (AHA) guidelines. We recommend the medical advisors in these shows to use AHA guidelines and AHA to expand its expenditures to include medical shows to educate the public on the appropriate action to rescue an out-of-hospital cardiac arrest patient.

Cost-Benefit Analyses of Transportation Investments

DEFF Research Database (Denmark)

Næss, Petter

2006-01-01

This paper discusses the practice of cost-benefit analyses of transportation infrastructure investment projects from the meta-theoretical perspective of critical realism. Such analyses are based on a number of untenable ontological assumptions about social value, human nature and the natural......-to-pay investigations. Accepting the ontological and epistemological assumptions of cost-benefit analysis involves an implicit acceptance of the ethical and political values favoured by these assumptions. Cost-benefit analyses of transportation investment projects tend to neglect long-term environmental consequences...

Automatic incrementalization of Prolog based static analyses

DEFF Research Database (Denmark)

Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

2007-01-01

Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic prog...

Improving Climate Communication through Comprehensive Linguistic Analyses Using Computational Tools

Science.gov (United States)

Gann, T. M.; Matlock, T.

2014-12-01

An important lesson on climate communication research is that there is no single way to reach out and inform the public. Different groups conceptualize climate issues in different ways and different groups have different values and assumptions. This variability makes it extremely difficult to effectively and objectively communicate climate information. One of the main challenges is the following: How do we acquire a better understanding of how values and assumptions vary across groups, including political groups? A necessary starting point is to pay close attention to the linguistic content of messages used across current popular media sources. Careful analyses of that information—including how it is realized in language for conservative and progressive media—may ultimately help climate scientists, government agency officials, journalists and others develop more effective messages. Past research has looked at partisan media coverage of climate change, but little attention has been given to the fine-grained linguistic content of such media. And when researchers have done detailed linguistic analyses, they have relied primarily on hand-coding, an approach that is costly, labor intensive, and time-consuming. Our project, building on recent work on partisan news media (Gann & Matlock, 2014; under review) uses high dimensional semantic analyses and other methods of automated classification techniques from the field of natural language processing to quantify how climate issues are characterized in media sources that differ according to political orientation. In addition to discussing varied linguistic patterns, we share new methods for improving climate communication for varied stakeholders, and for developing better assessments of their effectiveness.