Behavior of copper in acidic sulfate solution: Comparison with acidic chloride

Energy Technology Data Exchange (ETDEWEB)

Tromans, D.; Silva, J.C. [Univ. of British Columbia, Vancouver, British Columbia (Canada). Dept. of Metals and Materials Engineering

1997-03-01

The anodic polarization behavior of copper in a 0.1 M sulfuric acid (H{sub 2}SO{sub 4}) + 1 M sodium sulfate (Na{sub 2}SO{sub 4}) solution (pH = 2.0) was studied at room temperature under quiescent and stirred conditions. The behavior was compared with aqueous equilibria via construction of a potential-vs-pH (E-pH) diagram for the copper-sulfate-water (Cu-SO{sub 4}{sup 2}-H{sub 2}O) system. Interpretation of the behavior was aided by comparison with aqueous equilibria and polarization studies of copper in a 0.2 M hydrochloric acid (HCl) + 1 M sodium chloride (NaCl) solution(pH = 0.8). The initial anodic dissolution region in the acidic sulfate solution exhibited Tafel behavior with a slope consistent with formation of cupric ions (Cu{sup 2+}) whose rate of formation was charge-transfer controlled. At higher potentials, limiting current density (i{sub L}) behavior was observed under E-pH conditions that were consistent with formation of a film of copper sulfate pentahydrate (CuSO{sub 4} {degree} 5H{sub 2}O). Comparison of experimental i{sub L} values with those predicted by mass transport-controlled processes, using estimates of the diffusion layer thickness obtained from the mass transfer-influenced region of apparent Tafel behavior in the acidic chloride solution, were in sufficient agreement to indicate i{sub L} was controlled by the rate of dissolution of the CuSO{sub 4} {degree} 5H{sub 2}O film via transport of Cu{sup 2+} from the film-electrolyte interface into the bulk solution.

Zirconium for nitric acid solutions

International Nuclear Information System (INIS)

Yau, T.L.

1984-01-01

The excellent corrosion resistance of zirconium in nitric acid has been known for over 30 years. Recently, there is an increasing interest in using zirconium for nitric acid services. Therefore, an extensive research effort has been carried out to achieve a better understanding of the corrosion properties of zirconium in nitric acid. Particular attention is paid to the effect of concentration, temperature, structure, solution impurities, and stress. Immersion, autoclave, U-bend, and constant strain-rate tests were used in this study. Results of this study indicate that the corrosion resistance of zirconium in nitric acid is little affected by changes in temperature and concentration, and the presence of common impurities such as seawater, sodium chloride, ferric chloride, iron, and stainless steel. Moreover, the presence of seawater, sodium chloride, ferric chloride, and stainless steel has little effect on the stress corrosion craking (SCC) susceptibility of zirconium in 70% nitric acid at room temperatures. However, zirconium could be attacked by fluoride-containing nitric acid and the vapors of chloride-containing nitric acid. Also, high sustained tensile stresses should be avoided when zirconium is used to handle 70% nitric acid at elevated temperatures or > 70% nitric acid

A Novel Method for Fabricating Double Layers Porous Anodic Alumina in Phosphoric/Oxalic Acid Solution and Oxalic Acid Solution

Directory of Open Access Journals (Sweden)

Yanfang Xu

2016-01-01

Full Text Available A novel method for fabricating ordered double layers porous anodic alumina (DL-PAA with controllable nanopore size was presented. Highly ordered large pore layer with interpore distance of 480 nm was fabricated in phosphoric acid solution with oxalic acid addition at the potential of 195 V and the small pore layer was fabricated in oxalic acid solution at the potential from 60 to 100 V. Experimental results show that the thickness of large pore layer is linearly correlative with anodizing time, and pore diameter is linearly correlative with pore widening time. When the anodizing potential in oxalic acid solution was adjusted from 60 to 100 V, the small pore layers with continuously tunable interpore distance from 142 to 241 nm and pore density from 1.94×109 to 4.89×109 cm−2 were obtained. And the interpore distance and the pore density of small pore layers are closely correlative with the anodizing potential. The fabricated DL-PAA templates can be widely utilized for fabrication of ordered nanomaterials, such as superhydrophobic or gecko-inspired adhesive materials and metal or semiconductor nanowires.

Investigations on the oxidation of nitric acid plutonium solutions with ozone

International Nuclear Information System (INIS)

Boehm, M.

1983-01-01

The reaction of ozone with nitric acid Pu solutions was studied as a function of reaction time, acid concentration and Pu concentration. Strong nitric acid Pu solutions are important in nuclear fuel element production and reprocessing. The Pu must be converted into hexavalent Pu before precipitation from the homogeneous solution together with uranium-IV, ammonia and CO 2 in the form of ammonium uranyl/plutonyl carbonate (AUPuC). Formation of a solid phase during ozonation was observed for the first time. The proneness to solidification increases with incrasing plutonium concentrations and with decreasing acid concentrations. If the formation of a solid phase during ozonation of nitric acid Pu solutions cannot be prevented, the PU-IV oxidation process described is unsuitable for industrial purposes as Pu solutions in industrial processes have much higher concentrations than the solutions used in the present investigation. (orig./EF) [de

Waste acid/metal solution reduction and recovery by vacuum distillation

International Nuclear Information System (INIS)

Jones, E.O.; Wilcox, W.A.; Johnson, N.T.; Bowdish, F.W.

1995-01-01

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions

Corrosion control of vanadium in aqueous solutions by amino acids

International Nuclear Information System (INIS)

El-Rabiee, M.M.; Helal, N.H.; El-Hafez, Gh.M. Abd; Badawy, W.A.

2008-01-01

The electrochemical behavior of vanadium in amino acid free and amino acid containing aqueous solutions of different pH was studied using open-circuit potential measurements, polarization techniques and electrochemical impedance spectroscopy (EIS). The corrosion current density, i corr , the corrosion potential, E corr and the corrosion resistance, R corr , were calculated. A group of amino acids, namely, glycine, alanine, valine, histidine, glutamic and cysteine has been investigated as environmentally safe inhibitors. The effect of Cl - on the corrosion inhibition efficiency especially in acid solutions was investigated. In neutral and basic solutions, the presence of amino acids increases the corrosion resistance of the metal. The electrochemical behavior of V before and after the corrosion inhibition process has shown that some amino acids like glutamic acid and histidine have promising corrosion inhibition efficiency at low concentration (≅25 mM). The inhibition efficiency (η) was found to depend on the structure of the amino acid and the constituents of the corrosive medium. The corrosion inhibition process is based on the adsorption of the amino acid molecules on the metal surface and the adsorption process follows the Freundlich isotherm. The adsorption free energy for valine on V in acidic solutions was found to be -9.4 kJ/mol which reveals strong physical adsorption of the amino acid molecules on the vanadium surface

Vapor-liquid equilibria for nitric acid-water and plutonium nitrate-nitric acid-water solutions

International Nuclear Information System (INIS)

Maimoni, A.

1980-01-01

The liquid-vapor equilibrium data for nitric acid and nitric acid-plutnonium nitrate-water solutions were examined to develop correlations covering the range of conditions encountered in nuclear fuel reprocessing. The scanty available data for plutonium nitrate solutions are of poor quality but allow an order of magnitude estimate to be made. A formal thermodynamic analysis was attempted initially but was not successful due to the poor quality of the data as well as the complex chemical equilibria involved in the nitric acid and in the plutonium nitrate solutions. Thus, while there was no difficulty in correlating activity coefficients for nitric acid solutions over relatively narrow temperature ranges, attempts to extend the correlations over the range 25 0 C to the boiling point were not successful. The available data were then analyzed using empirical correlations from which normal boiling points and relative volatilities can be obtained over the concentration ranges 0 to 700 g/l Pu, 0 to 13 M nitric acid. Activity coefficients are required, however, if estimates of individual component vapor pressures are needed. The required ternary activity coefficients can be approximated from the correlations

Chemical dosimetry at less than 1000 rad: aqueous trimesic acid solutions

International Nuclear Information System (INIS)

Matthews, R.W.; Wilson, J.G.

1981-01-01

Aqueous solutions of trimesic acid were investigated for possible use as a chemical dosimeter. In aerated 10 -2 M sulphuric acid solution containing 10 -3 M trimesic acid, a highly fluorescent product is formed with its maximum fluorescence at 450nm when excited by 350nm light. The product has fluorescence characteristics very similar to quinine in 0.05 M sulphuric acid. The fluorescence intensity is linear with dose in the range 1-1000 rad and a precision of +-2% was obtained from a number of runs. Solutions are stable for at least several days before and after irradiation. The yield is little affected by moderate changes in trimesic acid concentration, oxygen concentration, water purity, energy of radiation and irradiation temperature. The small dependence of the yield on dose rate and the effect of measurement temperature on the fluorescence signal have been quantified. The most significant factor affecting the fluorescence signal is the hydrogen ion concentration of the solution. In aerated neutral and alkaline (pH 10) solutions, hydroxytrimesic acid (HTMA) is formed with G(HTMA) equal to 2.07 +- 0.04 and 2.21 +- 0.04, for 10 -3 M trimesate. In these solutions, G(HTMA) increases appreciably with increase in the trimesate concentration. The main fluorescent product formed in irradiated acid solutions was not identified but it was not HTMA. (author)

Polarography of hexavalent molybdenum in hypophosphorous acid solutions

International Nuclear Information System (INIS)

Hassan, A.; El-Shatory, S.A.; Azab, H.A.

1988-01-01

The polarographic behaviour and determination of Mo(6) in hypophosphorous acid solutions of concentrations varying from 0,1 to 5,0 moll -1 and T = 25±0,1 0 C have been investigated. It was shown that reduction of MoO 4 2- takes place along a single or two waves depending upon the acid concentration. Microcoulometric experiments have been performed at the limiting region of the different waves obtained at different acid concentrations. A scheme for the mechanism of reduction occuring at the DME has been deduced. A method for analytical determination of Mo(6) on both the micro- and macro-scales in hypophosphorous acid solutions has been reported. Analysis of a binary mixture Mo(6)/Cd(2) and a tertiary mixture Mo(6)/Cd(2)/Zn(2) in moll -1 hypophosphorous acid has been investigated. (Author)

Process for the removal of radium from acidic solutions containing same

Science.gov (United States)

Scheitlin, F.M.

The invention is a process for the removal of radium from acidic aqueous solutions. In one aspect, the invention is a process for removing radium from an inorganic-acid solution. The process comprises contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple, comparatively inexpensive, and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities throughout the United States. The invention is applicable, for example, to the recovery of /sup 226/Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings.

Recovery of Tin and Nitric Acid from Spent Solder Stripping Solutions

International Nuclear Information System (INIS)

Ahn, Jae-Woo; Ryu, Seong-Hyung; Kim, Tae-young

2015-01-01

Spent solder-stripping solutions containing tin, copper, iron, and lead in nitric acid solution, are by-products of the manufacture of printed-circuit boards. The recovery of these metals and the nitric acid, for re-use has economic and environmental benefits. In the spent solder-stripping solution, a systematic method to determine a suitable process for recovery of valuable metals and nitric acid was developed. Initially, more than 90% of the tin was successfully recovered as high-purity SnO 2 by thermal precipitation at 80 ℃ for 3 hours. About 94% of the nitric acid was regenerated effectively from the spent solutions by diffusion dialysis, after which there remained copper, iron, and lead in solution. Leakage of tin through the anion-exchange membrane was the lowest (0.026%), whereas Pb-leakage was highest (4.26%). The concentration of the regenerated nitric acid was about 5.1 N.

Gamma radiolysis of aqueous solution of ascorbic acid

International Nuclear Information System (INIS)

Loyola V, V.M.; Azamer B, J.A.; Laviada C, A.; Luna V, P.

1977-01-01

A preliminary study of the gamma radiolysis of a 1.13 x 10 -4 Maqueous solution of ascorbic acid is presented. It was found that dehydroascorbic acid was the principal product at doses of about 75 Krad. An increase in the dehydroascorbic acid concentration rangins from 5 to 40% was obtained, these values depend mainly on the initial ascorbic acid concentration. (author)

CO2 Capture from Flue Gas using Amino Acid Salt Solutions

DEFF Research Database (Denmark)

Lerche, Benedicte Mai; Stenby, Erling Halfdan; Thomsen, Kaj

2009-01-01

difficult. Amino acid salt solutions have emerged as an alternative to the alkanolamine solutions. A number of advantages make amino acid salt solutions attractive solvents for CO2 capture from flue gas. In the present study CO2 absorption in aqueous solutions of 0.5 M potassium glycinate and 0.5 M...

Water solubilization and the dielectric permeability of isomolar solutions of oleic acid and triethanolamine soap of oleic acid

Energy Technology Data Exchange (ETDEWEB)

Demchenko, P.A.; Novitskaya, L.D.

The investigation of the dependence of water solubilization on the dielectric permeability of isomolar solutions of oleic acid and triethanolamine soap of oleic acid in benzene has shown that at certain acid additions, the solubilization effect can increase almost 6 times, as compared to the soap solution without acid additions. In some cases, electron donor-acceptor complexes are formed, which are more polar than the original components. This leads to a change in the molecular-disperse and micellar part of solution and affects significantly the structure and properties of micellar hydrocarbon solutions of surfactants.

Reaction of nitrous acid with U(IV) and nitric acid in 30% TBP-kerosene solution

International Nuclear Information System (INIS)

Xu Xiangrong; Hu Jingxin; Huang Huaian; Qiu Xiaoxi

1990-01-01

Reaction of nitrous acid with U(IV) and nitric acid in 30% TBP-kerosene solution is investigated, the rate equations of oxidation of U(IV) by nitrous acid and that of nitrous acid reacting with nitric acid are obtained

Selective extraction of metals from acidic uranium(VI) solutions using neo-tridecano-hydroxamic acid

International Nuclear Information System (INIS)

Bardoncelli, F.; Grossi, G.

1975-01-01

According to this invention neo-alkyl-hydroxamic acids are employed as ion-exchanging agents in processes for liquid-liquid extraction with the aim of separating, purifying dissolved metals and of converting a metal salt solution into a solution of a salt of the same metal but with different anion. In particular it is an objective of this invention to provide a method whereby a molecular pure uranium solution is obtained by selective extraction from a uranium solution delivered by irradiated fuel reprocessing plants and containing plutonium, fission products and other unwanted metals, in which method neo-tridecane-hydroxamic acid is employed as ion exchanger. (Official Gazette)

Reaction Kinetics of Monomethylhydrazine With Nitrous Acid in Perchloric Acid Solution

International Nuclear Information System (INIS)

Wei Yan; Wang Hui; Pan Yongjun; Cong Haifeng; Jiao Haiyang; Jia Yongfen; Zheng Weifang

2009-01-01

The oxidation of monomethylhydrazine (MMH) by nitrous acid was researched in perchloric acid solution with spectrophotometry. The rate equation has been determined as follows: -dc (HNO 2 ) /dt= kc (H + ) 0.9 c (MMH) 1.1 c (HNO 2 ), k is (46.0 ± 2.7) L 2 / (mol 2 · s) with the initial perchlorate concentration of 0.50 mol/L at the temperature of 4.5 degree C. The corresponding activation energy of the reaction is (42.4 ± 0.1) kJ/mol. The results indicate that oxidation of mono-methylhydrazine (MMH) by nitrous acid is fast. The higher concentration of MMH can accelerate the reduction process of nitrous acid. Higher acidity can also speed up the reduction of nitrous acid. (authors)

Online Automatic Titration of Chromic Acid in Chromium Plating Solutions and Phosphoric and Sulfuric Acids in Electropolishing Solutions

National Research Council Canada - National Science Library

Sopok, Samuel

1991-01-01

.... The analytical chemistry literature lacks an adequate online automatic titration method for the monitoring of chromic acid in chromium plating solutions and the monitoring of phosphoric and sulfuric...

Vibrational studies in aqueous solutions. Part II. The acid oxalate ion and oxalic acid

Science.gov (United States)

Shippey, T. A.

1980-08-01

Assignments for oxalic acid in solution are re-examined. A detailed assignment of the IR and Raman spectra of the acid oxalate ion is presented for the first time. Raman spectroscopy is used to study the first ionization of oxalic acid.

Determination of free acid in plutonium (IV) solutions - thermometrically, potentiometrically

International Nuclear Information System (INIS)

Williams, T.L.; Tucker, G.M.; Huff, G.A.; Jordan, L.G.

1981-09-01

The thermometric titration technique was found to offer certain advantages over potentiometry in the determination of free acid in Pu(IV) solutions. The thermometric technique was applied to the determination of free acid in plutonium nitrate solutions using potassium fluoride to suppress the hydrolytic interference of plutonium(IV). The results indicate that 0.2 to 2.0 milliequivalents of free acid can be determined with acceptable bias and precision in solutions containing up to 30 milligrams of plutonium. In contrast, neither the thermometric nor the potentiometric technique was suitable for samples containing more than eight milligrams of plutonium complexed with potassium oxalate

15N NMR spectroscopic investigation of nitrous and nitric acids in sulfuric acid solutions of varying acidities

International Nuclear Information System (INIS)

Prakash, G.K.S.; Heiliger, L.; Olah, G.A.

1990-01-01

Both nitrous and nitric acids were studied in sulfuric acid solutions of varying acid strengths by 15 N NMR spectroscopy. The study gives new insights into the nature of intermediates present at different acid strengths. Furthermore, we have also discovered a novel redox reaction between NO 2 + and NO + ions involving the intermediacy of their respective acids. A mechanism is proposed to explain the observed results. 13 refs., 2 figs., 1 tab

Amination of oxy acids in aqueous solution by gamma-irradiation

International Nuclear Information System (INIS)

Ema, Kimiko; Kato, Taizo; Shinagawa, Mutsuaki

1978-01-01

Alanin, β-alanine, glicine, and aspartic, α-amino-n-butyric, and γ-amino-n-butyric acids were obtained by γ-irradiation of aqueous ammonia solutions of lactic, β-oxypropionic, glycolic, malic, α-oxybutyric, and γ-oxybutyric acids, respectively. The yields of amino acids were examined for functions of radiation dose (0.75 - 3.55Mrad), concentrations of oxy acid (0.01 - 0.1M) and ammonia (0.1 - 15M), and substances added as radical (potassium iodide), and hydrated electron (nitrous oxide) scavengers. The maximum G-values were 0.6 for alanine in a solution of 0.1M lactic acid-4M ammonia and some nitrous oxide and 1.14 for β-alanine in a solution of 0.1M β-oxypropionic acid and 0.7M ammonia. The yield of alanine increased with increased concentrations of lactic acid and ammonia due to saturation of nitrous oxide but decreased when potassium iodide (0.03M) was added. The yield of β-alanine showed a maximum increase at ca. 0.7M ammonia and decreased when potassium iodide and nitrous oxide were added. Serine was obtained from G = 0.002 in a solution of β-oxypropionic acid and increased to G = 0.058 due to saturation of nitrous oxide. The manner of chemical amination due to radiation was studied from the above results. In general, oxy acids from which hydrogen has been abstracted by an H or OH radical react with ammonia to form amino acids. The effect of ammonia concentration on the yield of amino acids demonstrates that the NH 2 radical abstracts the α-hydrogen of lactic acid but does not react with the β-hydrogen of β-oxypropionic acid. The effect of nitrous oxide indicates that hydrated electrons interfere with alanine formation, contribute to β-alanine formation, react with the carboxyl group of lactic acids to form lactamide, and abstract the β-hydroxyl group of β-oxypropionic acids to form β-alanine. (Bell, E.)

Solubility of xenon in amino-acid solutions. II. Nine less-soluble amino acids

Science.gov (United States)

Kennan, Richard P.; Himm, Jeffrey F.; Pollack, Gerald L.

1988-05-01

Ostwald solubility (L) of xenon gas, as the radioisotope 133Xe, has been measured as a function of solute concentration, at 25.0 °C, in aqueous solutions of nine amino acids. The amino-acid concentrations investigated covered much of their solubility ranges in water, viz., asparagine monohydrate (0-0.19 M), cysteine (0-1.16 M), glutamine (0-0.22 M), histidine (0-0.26 M), isoleucine (0-0.19 M), methionine (0-0.22 M), serine (0-0.38 M), threonine (0-1.4 M), and valine (0-0.34 M). We have previously reported solubility results for aqueous solutions of six other, generally more soluble, amino acids (alanine, arginine, glycine, hydroxyproline, lysine, and proline), of sucrose and sodium chloride. In general, L decreases approximately linearly with increasing solute concentration in these solutions. If we postulate that the observed decreases in gas solubility are due to hydration, the results under some assumptions can be used to calculate hydration numbers (H), i.e., the number of H2O molecules associated with each amino-acid solute molecule. The average values of hydration number (H¯) obtained at 25.0 °C are 15.3±1.5 for asparagine, 6.8±0.3 for cysteine, 11.5±1.1 for glutamine, 7.3±0.7 for histidine, 5.9±0.4 for isoleucine, 10.6±0.8 for methionine, 11.2±1.3 for serine, 7.7± 1.0 for threonine, and 6.6±0.6 for valine. We have also measured the temperature dependence of solubility L(T) from 5-40 °C for arginine, glycine, and proline, and obtained hydration numbers H¯(T) in this range. Between 25-40 °C, arginine has an H¯ near zero. This may be evidence for an attractive interaction between xenon and arginine molecules in aqueous solution.

Interactions of acidic solutions with sediments: a case study

International Nuclear Information System (INIS)

Peterson, S.R.; Serne, R.J.; Felmy, A.R.; Erikson, R.L.; Krupka, K.M.; Gee, G.W.

1984-01-01

A methodology is presented for investigating the chemical interactions of acidic solutions with sediments. The MINTEQ geochemical computer code was used to predict solid-phase reactions that might occur when acidic solutions contact neutral sediments which, in turn, may control the concentrations of certain dissolved components. Results of X-ray diffraction analysis of laboratory samples of sediments that have been contacted with acidic uranium mill tailings solutions suggest gypsum and jarosite precipitated. These same mineralogical changes were identified in sediment samples collected from a drained uranium mill evaporation pond (Lucky Mc mine in Wyoming) with a 10-year history of acid attack. Geochemical modeling predicted that these same phases and several amorphous solids not identifiable by X-ray diffraction should have precipitated in the contacted sediments. An equilibrium conceptual model consisting of an assemblage of minerals and amorphous solid phases was then developed to represent a sediment column through which uranium mill tailings solutions were percolated. The MINTEQ code was used to predict effluent solution concentrations resulting from the reactions of the tailings solution with the assemblage of solid phases in the conceptual model. The conceptual model successfully predicted the concentrations of several of the macro-constituents (e.g., Ca, SO 4 , Al, Fe, and Mn), but was not successful in modeling the concentrations of trace elements. The lack of success in predicting the observed trace metal concentrations suggests that other mechanisms, such as adsorption, must be included in future models. The geochemical modeling methodology coupled with the laboratory and field studies should be applicable to a variety of waste disposal problems

Process for the removal of radium from acidic solutions containing same

International Nuclear Information System (INIS)

Scheitlin, F.M.

1984-01-01

Radium is removed from an inorganic-acid solution contacting the solution with coal fly ash to effect adsorption of the radium on the ash. The radium-containing ash then is separated from the solution. The process is simple and efficient. High radium-distribution coefficients are obtained even at room temperature. Coal fly ash is an inexpensive, acid-resistant, high-surface-area material which is available in large quantities. The invention is applicable, for example, to the recovery of 226 Ra from nitric acid solutions which have been used to leach radium from uranium-mill tailings, and thus contain thorium and uranium. The contaminated fly ash may be incorporated in a suitable matrix and stored, and the residual solutions processed to separate uranium and thorium. (author)

Electrochemical dissolution of tin in methanesulphonic acid solutions

NARCIS (Netherlands)

de Greef, R.A.T.; Janssen, L.J.J.

2001-01-01

High-rate electroplating of tin on a moving steel strip is generally carried out in cells with dimensionally stable anodes. To obtain a matt tin deposit a concentrated acidic tin methanesulphonate solution containing a small concentration of sulphuric acid is used. The concentrated tin

Acid-base equilibrium in aqueous solutions of 1,3-dimethylbarbituric acid as studied by 13C NMR spectroscopy

Science.gov (United States)

Gryff-Keller, A.; Kraska-Dziadecka, A.

2011-12-01

13C NMR spectra of 1,3-dimethylbarbituric acid in aqueous solutions of various acidities and for various solute concentrations have been recorded and interpreted. The spectra recorded at pH = 2 and below contain the signals of the neutral solute molecule exclusively, while the ones recorded at pH = 7 and above only the signals of the appropriate anion, which has been confirmed by theoretical GIAO-DFT calculations. The signals in the spectra recorded for solutions of pH pH variation have been observed for the parent barbituric acid.

Co-precipitation of plutonium(IV) and americium(III) from nitric acid-oxalic acid solutions with bismuth oxalate

International Nuclear Information System (INIS)

Pius, I.C.; Noronha, D.M.; Chaudhury, Satyajeet

2017-01-01

Co-precipitation of plutonium and americium from nitric acid-oxalic acid solutions with bismuth oxalate has been investigated for the removal of these long lived α-active nuclides from waste solutions. Effect of concentration of bismuth and oxalic acid on the co-precipitation of Pu(IV) from 3 M HNO_3 has been investigated. Similar experiments were also carried out from 3.75 M HNO_3 on co-precipitation of Am(III) to optimize the conditions of precipitation. Strong co-precipitation of Pu(IV) and Am(III) with bismuth oxalate indicate feasibility of treatment of plutonium and americium bearing waste solutions. (author)

Adsorption of pertechnetate ion on various active carbons from mineral acid solutions

International Nuclear Information System (INIS)

Ito, K.

1991-01-01

The adsorption behavior of pertechnetate ion (TcO 4 - ) on active carbon has been studied for various acid solutions, taking as indicative value the distribution coefficient K d of Tc between active carbon surface and solution. In a system where the total anion concentration of the acid and its sodium salt was maintained constant, modifying the pH of the solution proved distinctly to influence the Tc adsorption behavior of active carbon: taking the case of active carbon derived from coconut shell, increasing the acidity raised K d ; around neutrality there occurred a level stage; in the alkali region, K d declined. The rise of K d in the acid region, however, was observed only with active carbon derived from coconut shell, from oil pitch or from saw dust; it failed to occur when the active carbon was derived from coal or from bone. With a hydrochloric acid system, the rise of K d started around 1 M (mol dm -1 ) HCl. Beyond 3 M, on the other hand, a breakthrough occurred, and K d declined with increasing acidity. With a nitric acid system, K d rose from 1 M, and the breakthrough occurred at 2 M. When the adsorption was left to equilibrate beyond 4 h, desorption displacement of TcO 4 - by a coexisting other anion was observed in the case of perchloric acid solutions of concentration above 0.1 M and with sulfuric acid solutions above 0.5 M. (author)

Investigations of the sorption of cesium from acid solutions by various inorganic sorbents

International Nuclear Information System (INIS)

Suess, M.; Pfrepper, G.

1981-01-01

Studies have been made to investigate the suitability of various inorganic sorbents for separating and obtaining cesium from acid solutions. In greater details, the distribution coefficients of cesium from nitric acid and ammonium nitrate solution were determined. To determine the saturation capacities it was necessary to plot the isotherms of adsorption from 0.5 N and 3.1 N nitric acid. Experimental sorption from a model solution, of which the composition was equal to that of the liquid Purex waste, enabled the suitability of the various exchangers for obtaining cesium from fission product solutions to be determined. From the results obtained it is apparent that ammonium phosphomolybdate is best suited for obtaining cesium from acid fission product solutions. (orig.)

Radiolysis of concentrated nitric acid solutions

International Nuclear Information System (INIS)

Nagaishi, R.; Jiang, P.Y.; Katsumura, Y.; Domae, M.; Ishigure, K.

1995-01-01

A study on electron pulse- and 60 Co γ-radiolysis of concentrated nitric acid and nitrate solutions has been carried out to elucidate the radiation induced reactions taking place in the solutions. Dissociation into NO 2 - and O( 3 P) was proposed as a direct action of the radiation on nitrate and gave the G-values were dependent on the chemical forms of nitrate: g s2 (-NO 3 - )=1.6 and g s2 (-HNO 3 )=2.2 (molecules/100eV). Based on the experimental yields of HNO 2 and reduced Ce IV , the primary yields of radiolysis products of water, g w , were evaluated to clarify the effects of nitrate on spur reactions of water in various nitrate solutions. (author)

Acid in perchloroethylene scrubber solutions used in HTGR fuel preparation processes. Analytical chemistry studies

International Nuclear Information System (INIS)

Lee, D.A.

1979-02-01

Acids and corrosion products in used perchloroethylene scrubber solutions collected from HTGR fuel preparation processes have been analyzed by several analytical methods to determine the source and possible remedy of the corrosion caused by these solutions. Hydrochloric acid was found to be concentrated on the carbon particles suspended in perchloroethylene. Filtration of carbon from the scrubber solutions removed the acid corrosion source in the process equipment. Corrosion products chemisorbed on the carbon particles were identified. Filtered perchloroethylene from used scrubber solutions contained practically no acid. It is recommended that carbon particles be separated from the scrubber solutions immediately after the scrubbing process to remove the source of acid and that an inhibitor be used to prevent the hydrolysis of perchloroethylene and the formation of acids

Radiolytic degradation of gallic acid and its derivatives in aqueous solution

International Nuclear Information System (INIS)

Melo, R.; Leal, J.P.; Takacs, E.; Wojnarovits, L.

2009-01-01

Polyphenols, like gallic acid (GA) released in the environment in larger amount, by inducing some unwanted oxidations, may constitute environmental hazard: their concentration in wastewater should be controlled. Radiolytic degradation of GA was investigated by pulse radiolysis and final product techniques in dilute aqueous solution. Subsidiary measurements were made with 3,4,5-trimethoxybenzoic acid (TMBA) and 3,4,5-trihydroxy methylbenzoate (MGA). The hydroxyl radical and hydrogen atom intermediates of water radiolysis react with the solute molecules yielding cyclohexadienyl radicals. The radicals formed in GA and MGA solutions in acid/base catalyzed water elimination decay to phenoxyl radicals. This reaction is not observed in TMBA solution. The hydrated electron intermediate of water decomposition adds to the carbonyl oxygen, the anion thus formed protonates on the ring forming cyclohexadienyl radical or on the carbonyl group forming carbonyl centred radical. The GA intermediates formed during reaction with primary water radicals in presence of oxygen transform to non-aromatic molecules, e.g., to aliphatic carboxylic acids.

Radiolytic degradation of gallic acid and its derivatives in aqueous solution

Energy Technology Data Exchange (ETDEWEB)

Melo, R. [Instituto Tecnologico e Nuclear, UCQR, Estrada Nacional No. 10, Apartado 21, 2686-953, Sacavem (Portugal); Leal, J.P. [Instituto Tecnologico e Nuclear, UCQR, Estrada Nacional No. 10, Apartado 21, 2686-953, Sacavem (Portugal); Centro Quimica e Bioquimica, Faculdade de Ciencias da Universidade de Lisboa, 1749-016 Lisboa (Portugal); Takacs, E., E-mail: takacs@iki.kfki.hu [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary); Wojnarovits, L. [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary)

2009-12-30

Polyphenols, like gallic acid (GA) released in the environment in larger amount, by inducing some unwanted oxidations, may constitute environmental hazard: their concentration in wastewater should be controlled. Radiolytic degradation of GA was investigated by pulse radiolysis and final product techniques in dilute aqueous solution. Subsidiary measurements were made with 3,4,5-trimethoxybenzoic acid (TMBA) and 3,4,5-trihydroxy methylbenzoate (MGA). The hydroxyl radical and hydrogen atom intermediates of water radiolysis react with the solute molecules yielding cyclohexadienyl radicals. The radicals formed in GA and MGA solutions in acid/base catalyzed water elimination decay to phenoxyl radicals. This reaction is not observed in TMBA solution. The hydrated electron intermediate of water decomposition adds to the carbonyl oxygen, the anion thus formed protonates on the ring forming cyclohexadienyl radical or on the carbonyl group forming carbonyl centred radical. The GA intermediates formed during reaction with primary water radicals in presence of oxygen transform to non-aromatic molecules, e.g., to aliphatic carboxylic acids.

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

International Nuclear Information System (INIS)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun; Seo, Jong Hyun; Choe, HeeHwan; Jeon, Jae-Hong; Hong, Munpyo; Lee, Yong Uk; Winkler, Joerg

2011-01-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm 2 to 26 mA/cm 2 , indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO 2 passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

Effect of acetic acid on wet patterning of copper/molybdenum thin films in phosphoric acid solution

Energy Technology Data Exchange (ETDEWEB)

Seo, Bo.-Hyun; Lee, Sang-Hyuk; Park, In-Sun [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Seo, Jong Hyun, E-mail: jhseo@kau.ac.kr [Department of Materials Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Choe, HeeHwan; Jeon, Jae-Hong [School of Electronics, Telecommunications and Computer Engineering, Korea Aerospace University, Hwajeon, Goyang, Gyonggi-do 412-791 (Korea, Republic of); Hong, Munpyo [Display and Semiconductor Physics, Korea University (Korea, Republic of); Lee, Yong Uk [PETEC (The Printable Electronics Technology Centre) (United Kingdom); Winkler, Joerg [PLANSEE Metal GmbH, Metallwerk-Plansee-Str. 71A-6600, Reutte (Austria)

2011-08-01

Copper metallization is a key issue for high performance thin film transistor (TFT) technology. A phosphoric acid based copper etchant is a potentially attractive alternative to the conventional hydrogen peroxide based etchant due to its longer-life expectancy time and higher stability in use. In this paper, it is shown that amount of the acetic acid in the phosphoric based copper etchant plays an important role in controlling the galvanic reaction between the copper and the molybdenum. As the concentration of acetic acid in the phosphoric mixture solution increased from 0 M to 0.4 M, the measured galvanic current density dropped from 32 mA/cm{sup 2} to 26 mA/cm{sup 2}, indicating that the acetic acid induces the lower galvanic reaction between the copper and the molybdenum in the solution. From the XPS analysis, with the addition of the acetic acid, the thickness of the protective MoO{sub 2} passive film covering the molybdenum surface grew and the dissolution rate of the molybdenum thin film decreased. However, the dissolution rate of the copper thin film increased as the concentration of acetic acid in the mixture solution increased.

Preparation of acid deficient solutions of uranyl nitrate and thorium nitrate by steam denitration

International Nuclear Information System (INIS)

Yamagishi, Shigeru; Takahashi, Yoshihisa

1996-01-01

Acid deficient heavy metal (HM) nitrate solutions are often required in the internal gelation processes for nuclear fuel fabrication. The stoichiometric HM-nitrate solutions are needed in a sol-gel process for fuel fabrication. A method for preparing such nitrate solutions with a controlled molar ratio of nitrate/metal by denitration of acid-excess nitrate solutions was developed. The denitration was conducted by bubbling a nitrate solution with a mixture of steam+Ar. It was found that steam was more effective for the denitration than Ar. The acid deficient uranyl nitrate solution with nitrate/U=1.55 was yielded by steam bubbling, while not by only Ar bubbling. As for thorium nitrate, acid deficient solutions of nitrate/Th≥3.1 were obtained by steam bubbling. (author)

Indium sulfide precipitation from hydrochloric acid solutions of calcium and sodium chlorides

International Nuclear Information System (INIS)

Kochetkova, N.V.; Bayandina, Yu.E.; Toptygina, G.M.; Shepot'ko, A.O.

1988-01-01

The effect of precipitation duration, acid concentration, indium complexing with chloride ions on the process of indium sulfide chemical precipitation in hydrochloric acid solutions, precipitate composition and dispersity are studied. It is established that indium sulfide solubility increases in solutions with acid concentration exceeding 0.40-0.45 mol/l. Calcium and indium chloride addition to diluted hydrochloric solutions greatly increases the solubility of indium sulfide. The effect of calcium chloride on In 2 S 3 solubility is higher than that of sodium chloride

Mechanism of the extraction of nitric acid and water by organic solutions of tertiary alkyl-amines; Mecanisme d'extraction de l'acide nitrique et de l'eau par les solutions organiques d'alcoylamines tertiaires

Energy Technology Data Exchange (ETDEWEB)

Gourisse, D

1966-06-01

The micellar aggregation of tri-alkyl-ammonium nitrates in low polarity organic solvents has been verified by viscosity, conductivity and sedimentation velocity measurements. The aggregation depends upon the polarity of solvent, the length of the alkyl radicals and the organic concentration of the various constituents (tri-alkyl-ammonium nitrate, tri-alkyl-amine, nitric acid, water). The amine salification law has been established and the excess nitric acid and water solubilities in the organic solutions have been measured. Nitric acid and water are slightly more soluble in micellar organic solutions than in molecular organic solutions. A description of excess nitric acid containing tri-alkyl-ammonium nitrate solutions is proposed. (author) [French] Mecanisme d'extraction de l'acide nitrique et de l'eau par les solutions organiques d'alcoylamines tertiaires. L'agregation micellaire des nitrates de trialcoylammonium dans les solvants peu polaires a ete verifiee par viscosimetrie, conductimetrie et ultracentrifugation des solutions organiques. L'agregation depend de la polarite du solvant, de la longueur des radicaux alcoyle, et des concentrations des differents constituants de la solution organique (nitrate de trialcoylammonium, alcoylamine tertiaire, acide nitrique, eau). La loi de salification de l'amine a ete determinee et les solubilites de l'acide nitrique en exces et de l'eau dans les solutions organiques ont ete mesurees. L'acide nitrique et l'eau sont legerement plus solubles dans les organiques micellaires que dans les solutions organiques moleculaires. Une description des solutions de nitrate de trialcoylammonium contenant de l'acide nitrique en exces est proposee. (auteur)

Determination of free nitric acid in uranyl nitrate solution

International Nuclear Information System (INIS)

Mayankutty, P.C.; Ravi, S.; Nadkarni, M.N.

1981-01-01

Potentiometric titration of uranyl nitrate solution with sodium hydroxide exhibits two peaks. The first peak characterises the following reaction, UO 2 (C 2 O 4 )+NaOH Na[UO 2 (C 2 O 4 )(OH)]. This reaction, indicating the partial hydrolysis of uranyl oxalate complex, appears to be complete at pH9. If the titration is carried out to this end-point pH, the total alkali consumed can be equated to the sum of uranium content and the free acidity present in the sample volume. Based on this, a method was standardised to determine the free acidity in uranyl nitrate solution. The sample, taken in a solution of potassium oxalate previously adjusted to pH9, is titrated to this pH with standard sodium hydroxide. The free acidity in the sample can be computed by subtracting the alkali reacted with uranium from the total alkali consumed. Analyses of several synthetic samples containing uranium and nitric acid in a wide range of combinations indicate that the free acidity can be accurately determined by this method, if uranium concentration in the sample is known. The results are compared to those obtained by two other widely used methods, viz., (i) titration of pH7 in the presence of neutral potassium oxalate to suppress hydrolysis and (ii) separation of hydrolyzable ions on a cationic resin and alkali titration of the free acid released. The advantages of and the precision obtained with the present method over the above two methods are discussed. (author)

Calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid

International Nuclear Information System (INIS)

Kurbanov, A.R.; Sharipov, D.Sh.

1993-01-01

Present article is devoted to calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid. The calorimetric study of interaction of barium hydroxide with diluted solutions of hydrofluoric acid was carried out in order to determine the thermal effects of reactions. The results of interaction of Ba(OH) 4 ·8H 2 O with 5, 10, and 20% solution of hydrofluoric acid were considered.

Ionizing radiation induced degradation of salicylic acid in aqueous solution

Science.gov (United States)

Albarrán, Guadalupe; Mendoza, Edith

2018-06-01

The radiation-induced degradation of salicylic acid (SA-) in aqueous solutions (1.0 and 0.1 mmol dm-3) saturated with N2O or air or without oxygen were studied. Irradiation was carried out using a cobalt-60 source. With a 1 mmol dm-3 solution saturated with N2O a seemingly total degradation occurred at about 18 kGy, although small quantities of 2,3-dihydroxybenzoic acid, catechol and 2,5-dihydroxybenzoic acid were present at that dose at concentrations of 67, 22 and 6 μmol dm-3 respectively. Under air and when free oxygen, the three radiolytic products were present at 18.54 kGy while SA- was destroyed only to 90% and 62%, respectively. In the case of 0.1 mmol dm-3 SA- solutions, the acid was degraded at 3.5 kGy if the solution contained N2O, at 5.8 kGy in air and at 7 kGy without oxygen. The concentration of the radiolytic products increased with increasing dose and after a maximum they decreased. The oxidation was followed by measuring the chemical oxygen demand; the slopes were 0.48 and 0.11, 0.21 and 0.07, 0.15 and 0.03 mmol dm-3 kGy-1 for 1.0 and 0.10 mmol dm-3 solutions saturated with N2O or air or without oxygen, respectively.

Interaction between Al3+ and acrylic acid and polyacrylic acid in acidic aqueous solution: a model experiment for the behavior of Al3+ in acidified soil solution.

Science.gov (United States)

Etou, Mayumi; Masaki, Yuka; Tsuji, Yutaka; Saito, Tomoyuki; Bai, Shuqin; Nishida, Ikuko; Okaue, Yoshihiro; Yokoyama, Takushi

2011-01-01

From the viewpoint of the phytotoxicity and mobility of Al(3+) released from soil minerals due to soil acidification, the interaction between Al(3+) and acrylic acid (AA) and polyacrylic acid (PAA) as a model compound of fulvic acid was investigated. The interaction was examined at pH 3 so as to avoid the hydrolysis of Al(3+). The interaction between Al(3+) and AA was weak. However, the interaction between Al(3+) and PAA was strong and depended on the initial (COOH in PAA)/Al molar ratio (R(P)) of the solution. For the range of 1/R(P), the interaction between Al(3+) and PAA can be divided into three categories: (1) 1:1 Al-PAA-complex (an Al(3+) combines to a carboxyl group), (2) intermolecular Al-PAA-complex (an Al(3+) combines to more than 2 carboxyl groups of other Al-PAA-complexes) in addition to the 1:1 Al-PAA-complex and (3) precipitation of intermolecular complexes. In conclusion, R(P) is an important factor affecting the behavior of Al(3+) in acidic soil solution.

Measuring and modeling aqueous electrolyte/amino-acid solutions with ePC-SAFT

International Nuclear Information System (INIS)

Held, Christoph; Reschke, Thomas; Müller, Rainer; Kunz, Werner; Sadowski, Gabriele

2014-01-01

Highlights: • Amino-acid solubilities and osmotic coefficients in ternary solutions containing one amino acids and one salt measured. • Weak salt influence on amino-acid solubilities except for salts containing Mg [2+] or NO 3 [−] (salting-in behavior). • Osmotic coefficients dominated by the solute with the highest molality. • Amino-acid solubilities and osmotic coefficients predicted reasonably with ePC-SAFT with deviations of 3.7% and 9.3%. • Predictions based on pure-component parameters for ions and amino acids using no ion/amino-acid fitting parameters. -- Abstract: In this work thermodynamic properties of electrolyte/amino acid/water solutions were measured and modeled. Osmotic coefficients at 298.15 K were measured by means of vapor-pressure osmometry. Amino-acid solubility at 298.15 K was determined gravimetrically. Considered aqueous systems contained one of the four amino acids: glycine, L-/DL-alanine, L-/DL-valine, and L-proline up to the respective amino-acid solubility limit and one of 13 salts composed of the ions Li + , Na + , K + , NH 4 + , Cl − , Br − , I − , NO 3 − , and SO 4 2− at salt molalities of 0.5, 1.0, and 3.0 mol · kg −1 , respectively. The data show that the salt influence is more pronounced on osmotic coefficients than on amino-acid solubility. The electrolyte Perturbed-Chain Statistical Association Theory (ePC-SAFT) was applied to model thermodynamic properties in aqueous electrolyte/amino-acid solutions. In previous works, this model had been applied to binary salt/water and binary amino acid/water systems. Without fitting any additional parameters, osmotic coefficients and amino-acid solubility in the ternary electrolyte/amino acid/water systems could be predicted with overall deviations of 3.7% and 9.3%, respectively, compared to the experimental data

Immobilization of citric acid solutions in portland cement

International Nuclear Information System (INIS)

Lopes, Valdir M.; Rzyski, Barbara M.

1997-01-01

Decontamination processes by using citric acid on certain items used in the nuclear area, can result in large volumes of liquid wastes with low activity or effluents, contaminated with uranium and some elements dangerous to the environment. A great number of installations that have decontamination processes adopt the zero discharge philosophy. So, one of the forms to isolate the solutions is by reducing its volume through the evaporation process. The generated must can be neutralized and encapsulated or immobilized in Portland cement. This work propose a chemical technique to destroy the citric acid in the decontamination solutions instead of neutralization and, depending on the installation convenience, a direct cement immobilization of these solutions or of the evaporation mud. The results obtained in this work involve data about the workability, setting time and mechanical resistance, after 28 days of sealed cure, for samples with water-cement ratios of 4, 0.5 and 0.6, by weight. (author). 5 refs., 2 tabs

Corrosion behavior of niobium coated 304 stainless steel in acid solution

Energy Technology Data Exchange (ETDEWEB)

Pan, T.J., E-mail: tjpan@cczu.edu.cn [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Jiangsu Key Laboratory of Material Surface Technology, Changzhou 213164 (China); Chen, Y.; Zhang, B. [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Hu, J. [School of Material Science and Engineering, Jiangsu Collaborative Innovation Center for Photovolatic Science and Engineering, Changzhou University, Changzhou 213164 (China); Jiangsu Key Laboratory of Material Surface Technology, Changzhou 213164 (China); Li, C. [Light Industry College of Liaoning University, Shenyang 110036 (China)

2016-04-30

Highlights: • The Nb coating produced by HEMAA offers good protection for 304SS in acid solution. • The coating increases corrosion potential and induces decrease of corrosion rate. • The protection of coating is ascribed to the stability of Nb in acid solution. - Abstract: The niobium coating is fabricated on the surface of AISI Type 304 stainless steel (304SS) by using a high energy micro arc alloying technique in order to improvecorrosion resistance of the steel against acidic environments. The electrochemical corrosion resistance of the niobium coating in 0.7 M sulfuric acid solutions is evaluated by electrochemical impedance spectroscopy, potentiodynamic polarization and the open circuit potential versus time. Electrochemical measurements indicate that the niobium coating increases the free corrosion potential of the substrate by 110 mV and a reduction in the corrosion rate by two orders of magnitude compared to the substrate alone. The niobium coating maintains large impedance and effectively offers good protection for the substrate during the long-term exposure tests, which is mainly ascribed to the niobium coating acting inhibiting permeation of corrosive species. Finally, the corresponding electrochemical impedance models are proposed to elucidate the corrosion resistance behavior of the niobium coating in acid solutions.

Corrosion behavior of niobium coated 304 stainless steel in acid solution

International Nuclear Information System (INIS)

Pan, T.J.; Chen, Y.; Zhang, B.; Hu, J.; Li, C.

2016-01-01

Highlights: • The Nb coating produced by HEMAA offers good protection for 304SS in acid solution. • The coating increases corrosion potential and induces decrease of corrosion rate. • The protection of coating is ascribed to the stability of Nb in acid solution. - Abstract: The niobium coating is fabricated on the surface of AISI Type 304 stainless steel (304SS) by using a high energy micro arc alloying technique in order to improvecorrosion resistance of the steel against acidic environments. The electrochemical corrosion resistance of the niobium coating in 0.7 M sulfuric acid solutions is evaluated by electrochemical impedance spectroscopy, potentiodynamic polarization and the open circuit potential versus time. Electrochemical measurements indicate that the niobium coating increases the free corrosion potential of the substrate by 110 mV and a reduction in the corrosion rate by two orders of magnitude compared to the substrate alone. The niobium coating maintains large impedance and effectively offers good protection for the substrate during the long-term exposure tests, which is mainly ascribed to the niobium coating acting inhibiting permeation of corrosive species. Finally, the corresponding electrochemical impedance models are proposed to elucidate the corrosion resistance behavior of the niobium coating in acid solutions.

Method for separation of Cs from acid solution dissolving radionuclides and microanalysis of solution with ICP-AES

International Nuclear Information System (INIS)

Kanazawa, Toru; Hidaka, Akihide; Kudo, Tamotsu; Nakamura, Takehiko; Fuketa, Toyoshi

2004-06-01

The VEGA (Verification Experiments of radionuclides Gas/Aerosol release) program is being performed at JAERI to understand mechanisms of radionuclides release from irradiated fuel during severe accidents. As a part of evaluation in the program, the mass balances of released and deposited FP (Fission Products) onto the test apparatus are estimated from gamma ray measurement for acid solution leached from the apparatus, but short-life nuclides are difficult to be measured because those in the VEGA fuel have been mostly depleted due to cooling for several years. Moreover, the radionuclides without emitting gamma rays and very small quantity of elements cannot be quantified by gamma ray measurement. Therefore, a microanalysis by ICP-AES (Inductively Coupled Plasma - Atomic Emission Spectrometry) for the acid solution leached from VEGA apparatuses is being applied to evaluate the released and deposited masses for those elements. Since Cs-134 and -137, which are major FP dissolved in the solution, have high intensity of gamma ray spectrum, they have to be removed from the solution before the microanalysis in order to avoid contamination of ICP system and to decrease exposure to gamma ray. In this report, methods for separation of Cs from acid solution were reviewed and the applicability of them to the ICP-AES analysis was discussed. The method for Cs separation using the inorganic ion exchanger, AMP (Ammonium Molybdate Phosphate) was applied to the solutions of cold and hot test and the effectiveness was examined. The results showed that more than 99.9% of Cs could be removed from the test solutions, and once removed Sb by AMP was recovered by using a complexing agent such as citric acid. Next, the method was applied to an acid solution leached from VEGA-3 apparatus, and ICP-AES analysis was performed for it. The analysis showed that amount of U, Sr and Zr were successfully quantified. Most of elements to be analyzed were measurable except for Sb, Ag and Sn, although

Treatment of infectious skin defects or ulcers with electrolyzed strong acid aqueous solution.

Science.gov (United States)

Sekiya, S; Ohmori, K; Harii, K

1997-01-01

A chronic ulcer with an infection such as methicillin-resistant Staphylococcus aureus is hard to heal. Plastic and reconstructive surgeons often encounter such chronic ulcers that are resistant to surgical or various conservative treatments. We applied conservative treatment using an electrolyzed strong acid aqueous solution and obtained satisfactory results. The lesion was washed with the solution or soaked in a bowl of the solution for approximately 20 min twice a day. Fresh electrolyzed strong acid aqueous solution is unstable and should be stored in a cool, dark site in a sealed bottle. It should be used within a week after it has been produced. Here we report on 15 cases of infectious ulcers that were treated by electrolyzed strong acid aqueous solution. Of these cases, 7 patients were healed, 3 were granulated, and in 5, infection subsided. In most cases the lesion became less reddish and less edematous. Discharge or foul odor from the lesion was decreased. Electrolyzed strong acid aqueous solution was especially effective for treating a chronic refractory ulcer combined with diabetes melitus or peripheral circulatory insufficiency. This clinically applied therapy of electrolyzed strong acid aqueous solution was found to be effective so that this new therapeutic technique for ulcer treatment can now be conveniently utilized.

Study of free acidity determinations in aqueous solution; Etude des dosages d'acidite libre en solution aqueuse

Energy Technology Data Exchange (ETDEWEB)

Kergreis, A [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1966-04-01

The object of this work is the study of the principal methods which can be applied to the measurement of 'free' acidity. In the first part, we define the various types of acidity which can exist in aqueous solution; then, after having studied some hydrolysis reactions, we compare the value of the neutralisation pH of the hydrated cation and that of the precipitation of the hydroxide. In the second part we have started to study the determination of the acidity of an aqueous solution. After having rapidly considered the 'total' acidity determination, we deal with the problem of the 'free' acidity titration. We have considered in particular certain methods: extrapolation of the equivalent point, colorimetric titrations with or without a complexing agent, and finally the use of ion-exchange resins with mixed aqueous and solvent solutions. (author) [French] Le but de ce travail est l'etude des principales methodes de determination de l'acidite 'libre'. Dans une premiere partie nous avons defini les differentes sortes d'acidites pouvant exister en solution aqueuse, puis apres avoir etudie quelques reactions d'hydrolyse, nous avons compare la valeur de pH de neutralisation du cation hydrate et celle de precipitation de l'hydroxyde. Dans la seconde partie nous avons aborde l'etuce des dosages de l'acidite d'une solution aqueuse. Apres avoir envisage assez rapidement la determination de l'acidite 'totale', nous traitons du probleme du titrage de l'acidite 'libre'. Nous avons porte notre attention sur certaines methodes: extrapolation du point equivalent, titrimetrie colorimetrique avec ou sans complexant, et enfin utilisation des resines echangeuses d'ions en milieu aqueux et solvant mixte.

Growth behavior of anodic porous alumina formed in malic acid solution

Science.gov (United States)

Kikuchi, Tatsuya; Yamamoto, Tsuyoshi; Suzuki, Ryosuke O.

2013-11-01

The growth behavior of anodic porous alumina formed on aluminum by anodizing in malic acid solutions was investigated. High-purity aluminum plates were electropolished in CH3COOH/HClO4 solutions and then anodized in 0.5 M malic acid solutions at 293 K and constant cell voltages of 200-350 V. The anodic porous alumina grew on the aluminum substrate at voltages of 200-250 V, and a black, burned oxide film was formed at higher voltages. The nanopores of the anodic oxide were only formed at grain boundaries of the aluminum substrate during the initial stage of anodizing, and then the growth region extended to the entire aluminum surface as the anodizing time increased. The anodic porous alumina with several defects was formed by anodizing in malic acid solution at 250 V, and oxide cells were approximately 300-800 nm in diameter.

Photolysis of Periodate and Periodic Acid in Aqueous Solution

DEFF Research Database (Denmark)

Sehested, Knud; Kläning, U. K.

1978-01-01

The photochemistry of periodate and periodic acid in aqueous solution was studied (i) by quantum yield measurements at low light intensity (ii) by flash photolysis, and (iii) by photolysis of glassy samples at 77 K. The photochemical studies were supplemented with pulse radiolysis studies...... of aqueous periodate solutions and with kinetic studies using stopped-flow technique. In strongly alkaline solution the photodecomposition of periodate proceeds via formation of O– and IVI. At pH solution O3 P is formed in a small...

Characterization of electrochemical and passive behaviour of Alloy 59 in acid solution

International Nuclear Information System (INIS)

Luo, Hong; Gao, Shujun; Dong, Chaofang; Li, Xiaogang

2014-01-01

Highlights: • A considerably thinner n-type passive film is observed on the Alloy-59. • The passive film formed in air was thicker than that formed in acid solution. • Primary constituents of passive film in air and acid solution are (Cr, Ni)-oxides and (Cr, Ni) hydroxides, respectively. - Abstract: The electrochemical behaviour and passive film properties of the Alloy 59 in sulfuric acid solution was evaluated by the potentiodynamic electrochemical measurements, electrochemical impedance spectroscopy, Mott-Schottky approach, and ex situ surface analytical technique as X-ray photoelectron spectroscopy (XPS) and Auger Electronic Spectrometer (AES). The results confirmed that the Alloy 59 exhibits well passive behaviour. A considerably thinner n-type passive film is observed on this type alloy. Based on the evaluations of surface composition analysis, the primary constituents of passive film formed in the air and acid solution are different, with the (Cr, Ni)-oxides and (Cr, Ni) hydroxides, respectively

Chemical dosimetry by UV spectrophotometry of aqueous ascorbic acid solutions

International Nuclear Information System (INIS)

Alian, A.; El-Assay, N.B.; Abdel-Rehim, F.; Amin, N.E.; McLaughlin, W.L.; Roushdy, H.

1984-01-01

The decrease in the ultraviolet absorption of aqueous solutions of ascorbic acid brought about by large doses of gamma radiation has been investigated as a means of developing a new chemical dosimeter. Because of spontaneous ring opening under various conditions after dissolution in water, some additives were examined as possible stabilizers against such denaturing of aqueous ascorbic acid. At an ascorbic acid concentration of 10 -4 M, either 1 to 2% glycine or 0.2 M NaCl was found to be a good stabilizer. A mechanism of radiation chemistry has been proposed based on hydroxyl radical and hydroxyl adduct intermediates, leading to dehydroascorbic acid through the ascorbate complex. The optimum dosimeter solution covers an absorbed dose range approx. 50 to 350 Gy, when measured at 264 nm wavelength. The G-values for dehydroascorbic acid production were determined to be 2.94 +- 0.33 and 2.43 +- 0.11 (100 eV) -1 , with glycine and NaCl used respectively as stabilizers. (author)

Hydrophobic interactions between polymethacrylic acid and sodium laureth sulfate in aqueous solutions

Science.gov (United States)

Yaremko, Z. M.; Fedushinskaya, L. B.; Burka, O. A.; Soltys, M. N.

2014-09-01

The role of hydrophobic interaction in the development of associative processes is demonstrated, based on the concentration dependences of the viscosity and pH of binary solutions of polymethacrylic acid as an anionic polyelectrolyte and sodium laureth sulfate as an anionic surfactant. It is found that the inflection point on the dependence of the difference between the pH values of binary solutions of polymethacrylic acid and sodium laureth sulfate on the polyelectrolyte concentration is a criterion for determining the predominant contribution from hydrophobic interaction, as is the inflection point on the dependence of pH of individual solutions of polymethacrylic acid on the polyelectrolyte concentration.

Studies of Tc oxidation states in humic acid solutions

International Nuclear Information System (INIS)

Wang Bo; Liu Dejun; Yao Jun

2011-01-01

The oxidation state of Tc is an important aspect of the speciation in groundwater which contained organic substances due to it control the precipitation, complexation, sorption and colloid formation behavior of the Tc under HWL geological disposal conditions. In present work, the oxidation states of Tc were investigated using the LaCl 3 coagulation method and solution extraction method in aqueous solutions in which the humic acid concentration range is from 0 to 20 mg/L and the Tc (VII) concentration is about 10 -8 mol/L. The radiocounting of 99 Tc was determined using liquid scintillation spectrometry. The humic acid will influence the radiocounting ratio of 99 Tc apparently, however, the quenching effect can be restrained once keep the volume of the cocktail to about twenty times of the sample volume. The LaCl 3 coagulation method was carried out for the investigation of Tc oxidation states in humic acid aqueous systems at about pH 8. The tetraphenylarsonium chloride (TPA)-chloroform extraction method was used also simultaneously to investigation the concentrations of Tc (IV) and Tc (VII) for the availability of the LaCl 3 precipitation method, and the experimental results demonstrate that tetravalent technetium and pertechnetate concentration are well agreement with the LaCl 3 precipitation method. These two experimental results demonstrated that Tc (VII) is very stable in the Tc (VII)-humic acid system during a 350 days experimental period, and the Tc (IV) concentrations are very lower, that is indicate that there didn't oxidizing reactions between the Fluka humic acid and Tc (VII) in aqueous solutions under anaerobic conditions. That means the presence of humic acids even in anaerobic groundwater is disadvantage for the retardance of radionuclides. (authors)

EPR spectra of vanadyl(2) intra-complexes with amino acids in solutions

International Nuclear Information System (INIS)

Shodiev, U.M.; Musaev, Z.M.; Khodzhaev, O.F.; Usmankhodzhaeva, Ya.S.; Parpiev, N.A.

1987-01-01

EPR spectra of vanadyl (2) intracomplexes with glycine, α- and β-alanines, benzoylglycine, lencine, glutamine and the aspartic acid of VOL 2 xH 2 O composition as well as with cystine of VOLxH 2 O composition (where L-monodeprotonated, in case of cystine and the aspartic acid - dideprotonated form of the amino acid) in aqueous, methanol, dimethylsulfoxide and pyridine solutions are studied. It is established that the structure determined in the solid state is retained in the dimethylsulfoxide solution and partially - in methanol. In aqueous, pyridine and partially in methanol solutions complexes are distorted and two molecules of the amino acid are coordinated monodentately through oxygen atoms of the carboxyl group, and ''vacant'' coordination places in the equatorial plane take two molecules of the solvent. From the data obtained it follows that the metal - nitrogen bond in the vanadyl (2) complexes studied with amino acids is not so strong than the metal - oxygen bond of the carboxyl ligand group

Enthalpic characteristics of interactions occurring between an ascorbic acid and some saccharides in aqueous solutions

International Nuclear Information System (INIS)

Terekhova, Irina V.; Kulikov, Oleg V.; Titova, Elena S.

2004-01-01

The enthalpies of solution of mono- and disaccharides were measured in water and aqueous ascorbic acid solutions at 298.15 K using a calorimeter of solution. Enthalpies of transfer of saccharides from water to aqueous ascorbic acid solutions were derived, and enthalpic coefficients of pair interaction h xy were calculated according to MacMillan-Mayer theory. Interactions of ascorbic acid with D-fructose and sucrose are energetically favorable and characterized by negative h xy coefficients while h xy for the interactions occurring between ascorbic acid and α-D glucose, D-galactose and maltose are positive. The obtained results are interpreted in terms of the influence of structure and solvation of solutes on the thermodynamic parameters of their interaction in solutions

Precipitation of plutonium from acidic solutions using magnesium oxide

International Nuclear Information System (INIS)

Jones, S.A.

1994-01-01

Magnesium oxide will be used as a neutralizing agent for acidic plutonium-containing solutions. It is expected that as the magnesium oxide dissolves, the pH of the solution will rise, and plutonium will precipitate. The resulting solid will be tested for suitability to storage. The liquid is expected to contain plutonium levels that meet disposal limit requirements

Savannah River Site Tank Cleaning: Corrosion Rate For One Versus Eight Percent Oxalic Acid Solution

International Nuclear Information System (INIS)

Ketusky, E.; Subramanian, K.

2011-01-01

Until recently, the use of oxalic acid for chemically cleaning the Savannah River Site (SRS) radioactive waste tanks focused on using concentrated 4 and 8-wt% solutions. Recent testing and research on applicable dissolution mechanisms have concluded that under appropriate conditions, dilute solutions of oxalic acid (i.e., 1-wt%) may be more effective. Based on the need to maximize cleaning effectiveness, coupled with the need to minimize downstream impacts, SRS is now developing plans for using a 1-wt% oxalic acid solution. A technology gap associated with using a 1-wt% oxalic acid solution was a dearth of suitable corrosion data. Assuming oxalic acid's passivation of carbon steel was proportional to the free oxalate concentration, the general corrosion rate (CR) from a 1-wt% solution may not be bound by those from 8-wt%. Therefore, after developing the test strategy and plan, the corrosion testing was performed. Starting with the envisioned process specific baseline solvent, a 1-wt% oxalic acid solution, with sludge (limited to Purex type sludge-simulant for this initial effort) at 75 C and agitated, the corrosion rate (CR) was determined from the measured weight loss of the exposed coupon. Environmental variations tested were: (a) Inclusion of sludge in the test vessel or assuming a pure oxalic acid solution; (b) acid solution temperature maintained at 75 or 45 C; and (c) agitation of the acid solution or stagnant. Application of select electrochemical testing (EC) explored the impact of each variation on the passivation mechanisms and confirmed the CR. The 1-wt% results were then compared to those from the 8-wt%. The immersion coupons showed that the maximum time averaged CR for a 1-wt% solution with sludge was less than 25-mils/yr for all conditions. For an agitated 8-wt% solution with sludge, the maximum time averaged CR was about 30-mils/yr at 50 C, and 86-mils/yr at 75 C. Both the 1-wt% and the 8-wt% testing demonstrated that if the sludge was removed from

Precipitation behavior of uranium in multicomponent solution by oxalic acid

International Nuclear Information System (INIS)

Shin, Y.J.; Kim, I.S.; Lee, W.K.; Shin, H.S.; Ro, S.G.

1996-01-01

A study on the precipitation of uranium by oxalic acid was carried out in a multicomponent solution. The precipitation method is usually applied to the treatment of radioactive waste and the recovery of uranium from a uranium-scrap contaminated with impurities. In these cases, the problem is how to increase the precipitation yield of target element and to prevent impurities from coprecipitation. The multicomponent solution in the present experiment was prepared by dissolving U, Nd, Cs and Sr in nitric acid. The effects of concentrations of oxalic acid and ascorbic acid on the precipitation yield and purity of uranium were observed. As results of the study, the maximum precipitation yield of uranium is revealed to be about 96.5% and the relative precipitation ratio of Nd, Cs and Sr versus uranium are discussed at the condition of the maximum precipitation yield of uranium, respectively. (author). 11 refs., 5 figs., 1 tab

Studying titanium-molybdenum-zirconium alloys of increased corrosion resistance in acid solutions

International Nuclear Information System (INIS)

Tomashov, N.D.; Kazarin, V.I.; Mikheev, V.S.; Goncharenko, B.A.; Sigalovskaya, T.M.; Kalyanova, M.P.

1977-01-01

New promising Ti-Mo-Nb-Zr system alloys, possessing good workability and a high corrosion resistance in non-oxidizing solutions of acids, have been developed. The alloys may be recommended as structural materials for equipment operating in severely agressive acid media, such as hydrochloric, sulphuric and phosphoric acids. The corrosion resistance of alloys of the above system in solutions of H 2 SO 4 , HCl and H 3 PO 4 acids may be maximized by increasing the overall alloying to 42% (keeping the ratio of the alloying components Mo/Nb/Zr=4/1/1 unchanged), while retaining sufficiently good plasticity and workability

Process for denitrating waste solutions containing nitric acid actinides simultaneously separating the actinides

International Nuclear Information System (INIS)

Gompper, K.

1984-01-01

The invention should reduce the acid and nitrate content of waste solutions containing nitric acid as much as possible, should reduce the total salt content of the waste solution, remove the actinides contained in it by precipitation and reduce the α radio-activity in the remaining solution, without having to worry about strong reactions or an increase in the volume of the waste solution. The invention achieves this by mixing the waste solution with diethyl oxalate at room temperature and heating the mixture to at least 80 0 C. (orig.) [de

Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part I. Regeneration of Amine-Carboxylic Acid Extracts

Energy Technology Data Exchange (ETDEWEB)

Poole, Loree Joanne [Univ. of California, Berkeley, CA (United States); King, C. Judson [Univ. of California, Berkeley, CA (United States)

1990-03-01

Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO₂ and H₂S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, succinic acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The

Compatible solutes in lactic acid bacteria subjected to water stress

NARCIS (Netherlands)

Kets, E.P.W.

1997-01-01

The goal of the research project described in this thesis was to investigate the protective effect of compatible solutes on tactic acid bacteria subjected to drying. Dried preparations of lactic acid bacteria are applied as starter cultures in feed and food industries. Dried starter

Hyaluronic acid solution injection for upper and lower gastrointestinal bleeding after failed conventional endoscopic therapy.

Science.gov (United States)

Lee, Jin Wook; Kim, Hyung Hun

2014-03-01

Hyaluronic acid solution injection can be an additional endoscopic modality for controlling bleeding in difficult cases when other techniques have failed. We evaluated 12 cases in which we used hyaluronic acid solution injection for stopping bleeding. Immediately following hyaluronic acid solution injection, bleeding was controlled in 11 out of 12 cases. There was no clinical evidence of renewed bleeding in 11 cases during follow up.Hyaluronic acid solution injection can be a simple and efficient additional method for controlling upper and lower gastrointestinal bleeding after failed endoscopic therapy. © 2013 The Authors. Digestive Endoscopy © 2013 Japan Gastroenterological Endoscopy Society.

Effect of citric acid on the acidification of artificial pepsin solution for metacercariae isolation from fish.

Science.gov (United States)

Kim, Min-Ki; Pyo, Kyoung-Ho; Hwang, Young-Sang; Chun, Hyang Sook; Park, Ki Hwan; Ko, Seong-Hee; Chai, Jong-Yil; Shin, Eun-Hee

2013-11-15

Artificial digestive solution based on pepsin is essential for collecting metacercariae from fish. To promote the enzymatic reactivity of pepsin, the pH of the solution has to be adjusted to pH 1.0-2.0. Hydrochloride (HCl) is usually used for this purpose, but the use of HCl raises safety concerns. The aim of this work was to address the usefulness of citric acid as an alternative for HCl for the acidification of pepsin solution, and to examine its potential to damage metacercariae during in vitro digestion as compared with HCl. Changes in pH after adding 1-9% of citric acid (m/v) to pepsin solution were compared to a 1% HCl (v/v) addition. Digestion of fish muscle was evaluated by measuring released protein concentrations by spectrophotometry. In addition, survival rates of metacercariae in pepsin solution were determined at different citric acid concentrations and were compared that of with 1% HCl. The present study shows that addition of citric acid reduced the pH of pepsin solutions to the required level. Addition of more than 5% of citric acid resulted in the effective digestion of fish muscle over 3h in vitro, and 5% citric acid was less lethal to metacercariae than 1% HCl in pepsin solution. Pepsin solution containing 5% citric acid had digestive capacity superior to pepsin solution containing 1% HCl after 3h incubation with released protein concentrations of 12.0 ng/ml for 5% citric acid and 9.6 ng/ml for 1% HCl. Accordingly, the present study suggests that the addition of 5% citric acid to pepsin solution is a good alternative to 1% HCl in infection studies because citric acid is a stable at room temperature and has a good safety profile. In addition, we suggest that the use of citric acid enables the preparation of commercial digestive solutions for the detection of microorganisms in fish and other vertebrate muscle tissue. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

Chloride stress corrosion cracking of Alloy 600 in boric acid solutions

International Nuclear Information System (INIS)

Berge, Ph.; Noel, D.; Gras, J.M.; Prieux, B.

1997-10-01

The high nickel austenitic alloys are generally considered to have good resistance to chloride stress corrosion cracking. In the standard boiling magnesium chloride solution tests, alloys with more than 40% nickel are immune. Nevertheless, more recent data show that cracking can occur in both Alloys 600 and 690 if the solution is acidified. In other low pH media, such as boric acid solution at 100 deg C, transgranular and intergranular cracking are observed in Alloy 600 in the presence of minor concentrations of sodium chloride (2g/I). In concentrated boric acid at higher temperatures (250 and 290 deg C), intergranular cracking also occurs, either when the chloride concentration is high, or at low chloride contents and high oxygen levels. The role of pH and a possible specific action of boric acid are discussed, together with the influence of electrochemical potential. (author)

Structure of polyacrylic acid and polymethacrylic acid solutions: a small angle neutron scattering study

Energy Technology Data Exchange (ETDEWEB)

Moussaid, A. (Lab. d' Ultrasons et de Dynamique des Fluides Complexes, Univ. Louis Pasteur, 67 - Strasbourg (France)); Schosseler, F. (Lab. d' Ultrasons et de Dynamique des Fluides Complexes, Univ. Louis Pasteur, 67 - Strasbourg (France)); Munch, J.P. (Lab. d' Ultrasons et de Dynamique des Fluides Complexes, Univ. Louis Pasteur, 67 - Strasbourg (France)); Candau, S.J. (Lab. d' Ultrasons et de Dynamique des Fluides Complexes, Univ. Louis Pasteur, 67 - Strasbourg (France))

1993-04-01

The intensity scattered from polyacrylic acid and polymethacrylic acid solutions has been measured by small angle neutron scattering experiments. The influence of polymer concentration, ionization degree, temperature and salt content has been investigated. Results are in qualitative agreement with a model which predicts the existence of microphases in the unstable region of the phase diagram. Quantitative comparison with the theory is performed by fitting the theoretical structure factor to the experimental data. For a narrow range of ionization degrees nearly quantitative agreement with the theory is found for the polyacrylic acid system. (orig.).

Structure of polyacrylic acid and polymethacrylic acid solutions : a small angle neutron scattering study

Science.gov (United States)

Moussaid, A.; Schosseler, F.; Munch, J. P.; Candau, S. J.

1993-04-01

The intensity scattered from polyacrylic acid and polymethacrylic acid solutions has been measured by small angle neutron scattering experiemnts. The influence of polymer concentration, ionization degree, temperature and salt content has been investigated. Results are in qualitative agreement with a model which predicts the existence of microphases in the unstable region of the phase diagram. Quantitative comparison with the theory is performed by fitting the theoretical structure factor to the experimental data. For a narrow range of ionizaiton degrees nearly quantitative agreement with the theory is found for the polyacrylic acide system.

Dissolution study of thorium-uranium oxides in aqueous triflic acid solutions

Energy Technology Data Exchange (ETDEWEB)

Bulemela, E.; Bergeron, A.; Stoddard, T. [Canadian Nuclear Laboratories - CNL, 286 Plant Rd., Chalk River, Ontario, K0J 1J0 (Canada)

2016-07-01

The dissolution of sintered mixed oxides of thorium with uranium in various concentrations of trifluoromethanesulfonic (triflic) acid solutions was investigated under reflux conditions to evaluate the suitability of the method. Various fragment sizes (1.00 mm < x < 7.30 mm) of sintered (Th,U)O{sub 2} and simulated high-burnup nuclear fuel (SIMFUEL) were almost completely dissolved in a few hours, which implies that triflic acid could be used as an alternative to the common dissolution method, involving nitric acid-hydrofluoric acid mixture. The influence of acid concentration, composition of the solids, and reaction time on the dissolution yield of Th and U ions was studied using Inductively Coupled Plasma - Mass Spectrometry (ICP-MS). The dissolution rate was found to depend upon the triflic acid concentration and size of the solid fragments, with near complete dissolution for the smallest fragments occurring in boiling 87% w/w triflic acid. The formation of Th and U ions in solution appears to occur at the same rate as the triflic acid simultaneously reacts with the constituent oxides as evidenced by the results of a constant U/Th concentration ratio with the progress of the dissolution. (authors)

Adsorption of zirconium from nitric acid solutions on hydrated tin dioxide

Energy Technology Data Exchange (ETDEWEB)

Tret' yakov, S Ya; Sharygin, L M; Egorov, Yu V

1977-01-01

Adsorption of zirconium from nitric acid solutions has been studied with the use of the labeled atom method on hydrated tin dioxide depending on the sorbate concentration, pH and prehistory of the solution. It has been found that adsorption behavior of zirconium essentially depends on its state in the solution.

Amino acid salt solutions as solvents in CO2 capture from flue gas

DEFF Research Database (Denmark)

Lerche, Benedicte Mai; Thomsen, Kaj; Stenby, Erling Halfdan

New solvents based on the salts of amino acids have emerged as an alternative to the alkanolamine solutions, for the chemical absorption of CO2 from flue gas. But only few studies on amino acids as CO2 capturing agents have been performed so far. One of the interesting features of amino acid salt...... solutions is their ability to form solid precipitates upon the absorption of CO2. The occurrence of crystallization offers the possibility of increasing the CO2 loading capacity of the solvent. However, precipitation can also have negative effect on the CO2 capture process. The chemical nature of the solid...... of glycine, taurine, and lysine, while in the case of proline, and glutamic acid, the precipitate was found to be bicarbonate. These results give an important contribution to further understanding the potential of amino acid salt solutions in CO2 capture from flue gas....

Extraction of plutonium and uranium from oxalate bearing solutions using phosphonic acid

International Nuclear Information System (INIS)

Godbole, A.G.; Mapara, P.M.; Swarup, Rajendra

1995-01-01

A feasibility study on the solvent extraction of plutonium and uranium from solutions containing oxalic and nitric acids using a phosphonic acid extractant (PC88A) was made to explore the possibility of recovering Pu from these solutions. Batch experiments on the extraction of Pu(IV) and U(VI) under different parameters were carried out using PC88A in dodecane. The results indicated that Pu could be extracted quantitatively by PC88A from these solutions. A good separation of Pu from U could be achieved at higher temperatures. (author). 6 refs., 3 tabs

Behaviour of Pu-IV with various ion exchangers in solutions containing nitric acid and oxalates

International Nuclear Information System (INIS)

Walter, E.; Ali, S.A.

1982-02-01

The distribution of Pu-IV on the ion exchangers Dowex 50W-X8, Dowex 1-X8 und Dowex Chelating Resin Al-X8 in the presence of various concentrations of nitric acid and oxalate were investigated. The results indicate that nitric acid and oxalic acid influence each other during complexation of Pu-IV with oxalate ions solutions containing nitric acid it is not possible to neglect the formation of Pu-IV nitrate complexes. The complex Pu(IV) (C 2 O 4 ) 3 2 - only is formed in solutions containing low nitric acid and high oxalic acid concentrations. The separation of Pu-IV in Dowex Chelating Resin from nitric acid solution in the presence of higher oxalate concentrations is possible, provided that the nitric acid concentration is lower than 0.25 molar [fr

Radiolysis studies of uranyl nitrate solution in nitric acid medium

International Nuclear Information System (INIS)

Siri, Sandra; Mondino, Angel V.

2005-01-01

The radiolysis of acidic uranyl nitrate solutions was investigated using Co-60 gamma radiation. Hydrogen peroxide was determined as a function of increasing dose. The UV-vis absorption spectra of the irradiated solutions were measured and the spectral changes were analyzed. The increasing dose increases the absorbance intensities, possibly by an increment in nitrate concentration produced by radiolysis, which can originate the formation of different uranyl complexes in solution. (author)

Coprecipitation of thorium and uranium peroxides from acid solutions

Energy Technology Data Exchange (ETDEWEB)

McTaggart, D.R.; Mailen, J.C.

1981-01-01

The factors affecting successful coprecipitation of thorium and uranium peroxides from acid media were studied. Variables considered in this work were H/sup +/ concentration, H/sub 2/O/sub 2/ concentration, duration of contact, and rate of feed solution addition. In all experiments, stock solutions of Th(NO/sub 3/)/sub 4/ and UO/sub 2/(NO/sub 3/)/sub 2/ were fed at a controlled rate into H/sub 2/O/sub 2/ solutions with constant stirring. Samples were taken as a function of time to follow the H/sup +/ concentration of the solution, uranium precipitation, thorium precipitation, precipitant weight/volume of solution, and crystalline structure and growth. The optimum conditions for maximum coprecipitation are low H/sup +/ concentration, high H/sub 2/O/sub 2/ concentration, and extended contact time between the solutions.

Structure of polyacrylic acid and polymethacrylic acid solutions : a small angle neutron scattering study

OpenAIRE

Moussaid , A.; Schosseler , F.; Munch , J.; Candau , S.

1993-01-01

The intensity scattered from polyacrylic acid and polymethacrylic acid solutions has been measured by small angle neutron scattering experiemnts. The influence of polymer concentration, ionization degree, temperature and salt content has been investigated. Results are in qualitative agreement with a model which predicts the existence of microphases in the unstable region of the phase diagram. Quantitative comparison with the theory is performed by fitting the theoretical structure factor to t...

Effect of temperature on the dilution enthalpies of α,ω-amino acids in aqueous solutions

International Nuclear Information System (INIS)

Romero, C.M.; Cadena, J.C.; Lamprecht, I.

2011-01-01

Highlights: → The dilution of 3-amino propanoic acid, 4-amino butanoic acid, 5-amino pentanoic acid, and 6-amino hexanoic acid in water is an exothermic process at T = (293.15, 298.15, 303.15, and 308.15) K. → The limiting experimental slopes of the enthalpies of dilution with respect to the molality change Δm, are negative suggesting that the solutes interact with water primarily through their alkyl groups. → The value of the pairwise coefficient is positive at the temperatures considered, and the magnitude increases linearly with the number of methylene groups. → The comparison between the pairwise interaction coefficients for α,ω-amino acids and α-amino acids shows that the change in the enthalpic interaction coefficient is related to the relative position of the polar groups. - Abstract: Dilution enthalpies of aqueous solutions of 3-amino propanoic acid, 4-amino butanoic acid, 5-amino pentanoic acid, and 6-amino hexanoic acid were determined at T = (293.15, 298.15, 303.15, and 308.15) K using an LKB flow microcalorimeter. The homotactic interaction coefficients were obtained according to the McMillan-Mayer theory from the experimental data. For all the systems studied, the dilution of α,ω-amino acids in water is an exothermic process; the pair coefficients have positive values which increases with chain length. The obtained values of the interaction coefficients are interpreted in terms of solute-solvent and solute-solute interactions and are used as indicative of hydrophobic behavior of the amino acid studied.

A new approach to study cadmium complexes with oxalic acid in soil solution.

Science.gov (United States)

Dytrtová, Jana Jaklová; Jakl, Michal; Sestáková, Ivana; Zins, Emilie-Laure; Schröder, Detlef; Navrátil, Tomáš

2011-05-05

This study presents a new analytical approach for the determination of heavy metals complexed to low-molecular-weight-organic acids in soil solutions, which combines the sensitivity of differential pulse anodic stripping voltammetry (DPASV) with the molecular insight gained by electrospray ionization mass spectrometry (ESI-MS). The combination of these analytical methods allows the investigation of such complexes in complex matrixes. On the voltammograms of the soil solutions, in addition to the expected complexes of oxalic acid with cadmium and lead, respectively, also peaks belonging to mixed complexes of cadmium, lead, and oxalic acid (OAH(2)) were observed. In order to verify the possible formation of complexes with OAH(2), aqueous solutions of OAH(2) with traces of Cd(II) were investigated as model systems. Signals corresponding to several distinct molecular complexes between cadmium and oxalic acid were detected in the model solutions using negative-ion ESI-MS, which follow the general formula [Cd(n)(X,Y)((2n+1))](-), where n is the number of cadmium atoms, X=Cl(-), and Y=OAH(-). Some of these complexes were also identified in the ESI mass spectra taken from the soil solutions. Copyright © 2011 Elsevier B.V. All rights reserved.

A new approach to study cadmium complexes with oxalic acid in soil solution

International Nuclear Information System (INIS)

Jaklova Dytrtova, Jana; Jakl, Michal; Sestakova, Ivana; Zins, Emilie-Laure; Schroeder, Detlef; Navratil, Tomas

2011-01-01

This study presents a new analytical approach for the determination of heavy metals complexed to low-molecular-weight-organic acids in soil solutions, which combines the sensitivity of differential pulse anodic stripping voltammetry (DPASV) with the molecular insight gained by electrospray ionization mass spectrometry (ESI-MS). The combination of these analytical methods allows the investigation of such complexes in complex matrixes. On the voltammograms of the soil solutions, in addition to the expected complexes of oxalic acid with cadmium and lead, respectively, also peaks belonging to mixed complexes of cadmium, lead, and oxalic acid (OAH 2 ) were observed. In order to verify the possible formation of complexes with OAH 2 , aqueous solutions of OAH 2 with traces of Cd(II) were investigated as model systems. Signals corresponding to several distinct molecular complexes between cadmium and oxalic acid were detected in the model solutions using negative-ion ESI-MS, which follow the general formula [Cd n (X,Y) (2n+1) ] - , where n is the number of cadmium atoms, X = Cl - , and Y = OAH - . Some of these complexes were also identified in the ESI mass spectra taken from the soil solutions.

A new approach to study cadmium complexes with oxalic acid in soil solution

Energy Technology Data Exchange (ETDEWEB)

Jaklova Dytrtova, Jana, E-mail: dytrtova@uochb.cas.cz [Institute of Organic Chemistry and Biochemistry of the AS CR, v.v.i., Flemingovo namesti 2, 16610 Prague 6 (Czech Republic); Jakl, Michal [Department of Agro-Environmental Chemistry and Plant Nutrition, Faculty of Agrobiology, Food and Natural Resources, Czech University of Life Sciences, Kamycka 129, 16521 Prague - Suchdol (Czech Republic); Sestakova, Ivana [J. Heyrovsky Institute of Physical Chemistry of the AS CR, v.v.i., Dolejskova 3, 182 23 Prague 8 (Czech Republic); Zins, Emilie-Laure; Schroeder, Detlef [Institute of Organic Chemistry and Biochemistry of the AS CR, v.v.i., Flemingovo namesti 2, 16610 Prague 6 (Czech Republic); Navratil, Tomas [J. Heyrovsky Institute of Physical Chemistry of the AS CR, v.v.i., Dolejskova 3, 182 23 Prague 8 (Czech Republic)

2011-05-05

This study presents a new analytical approach for the determination of heavy metals complexed to low-molecular-weight-organic acids in soil solutions, which combines the sensitivity of differential pulse anodic stripping voltammetry (DPASV) with the molecular insight gained by electrospray ionization mass spectrometry (ESI-MS). The combination of these analytical methods allows the investigation of such complexes in complex matrixes. On the voltammograms of the soil solutions, in addition to the expected complexes of oxalic acid with cadmium and lead, respectively, also peaks belonging to mixed complexes of cadmium, lead, and oxalic acid (OAH{sub 2}) were observed. In order to verify the possible formation of complexes with OAH{sub 2}, aqueous solutions of OAH{sub 2} with traces of Cd(II) were investigated as model systems. Signals corresponding to several distinct molecular complexes between cadmium and oxalic acid were detected in the model solutions using negative-ion ESI-MS, which follow the general formula [Cd{sub n}(X,Y){sub (2n+1)}]{sup -}, where n is the number of cadmium atoms, X = Cl{sup -}, and Y = OAH{sup -}. Some of these complexes were also identified in the ESI mass spectra taken from the soil solutions.

Determination of humic acid in alkali leaching solution of uranium by spectophotrometry-COD method

International Nuclear Information System (INIS)

Feng Yu; An Wei; Chen Shusen

2014-01-01

It is one of the main causes of extraction emulsification or resin toxicosis during alkali leaching process in uranium metallurgy which organic matters including humic acid exist in lixiviums. In order to study the effect of humic acid in uranium metallurgy, a method for determination of content of humic acid in aqueous solution need to be established. Spectrophotometry is a simple and convenient method in humic acid analysis. However, accuracy of spectrophotometry can be reduced greatly because of interference of uranium and other elements in the humic acid solutions. Although chemical oxygen demand (COD) method is a common analysis way of organic matters in aqueous solutions, the concentration of humic acid cannot be directly measured. In this paper, COD method is related with spectrophotometry to avoid the interference of uranium and ensure the accurate analysis of humic acid. The results showed that the detection limit of the method was 1.78 mg/L and the recovery rate was 101.2%. (authors)

Dissolution of Simulated and Radioactive Savannah River Site High-Level Waste Sludges with Oxalic Acid & Citric Acid Solutions

International Nuclear Information System (INIS)

STALLINGS, MARY

2004-01-01

This report presents findings from tests investigating the dissolution of simulated and radioactive Savannah River Site sludges with 4 per cent oxalic acid and mixtures of oxalic and citric acid previously recommended by a Russian team from the Khlopin Radium Institute and the Mining and Chemical Combine (MCC). Testing also included characterization of the simulated and radioactive waste sludges. Testing results showed the following: Dissolution of simulated HM and PUREX sludges with oxalic and citric acid mixtures at SRTC confirmed general trends reported previously by Russian testing. Unlike the previous Russian testing six sequential contacts of a mixture of oxalic acid citric acids at a 2:1 ratio (v/w) of acid to sludge did not produce complete dissolution of simulated HM and PUREX sludges. We observed that increased sludge dissolution occurred at a higher acid to sludge ratio, 50:1 (v/w), compared to the recommended ratio of 2:1 (v/w). We observed much lower dissolution of aluminum in a simulated HM sludge by sodium hydroxide leaching. We attribute the low aluminum dissolution in caustic to the high fraction of boehmite present in the simulated sludge. Dissolution of HLW sludges with 4 per cent oxalic acid and oxalic/citric acid followed general trends observed with simulated sludges. The limited testing suggests that a mixture of oxalic and citric acids is more efficient for dissolving HM and PUREX sludges and provides a more homogeneous dissolution of HM sludge than oxalic acid alone. Dissolution of HLW sludges in oxalic and oxalic/citric acid mixtures produced residual sludge solids that measured at higher neutron poison to equivalent 235U weight ratios than that in the untreated sludge solids. This finding suggests that residual solids do not present an increased nuclear criticality safety risk. Generally the neutron poison to equivalent 235U weight ratios of the acid solutions containing dissolved sludge components are lower than those in the untreated

Process for recovering uranium using an alkyl pyrophosphoric acid and alkaline stripping solution

International Nuclear Information System (INIS)

Worthington, R.E.; Magdics, A.

1987-01-01

A process is described for stripping uranium for a pregnant organic extractant comprising an alkyl pyrophosphoric acid dissolved in a substantially water-immiscible organic diluent. The organic extractant contains tetravalent uranium and an alcohol or phenol modifier in a quantity sufficient to retain substantially all the unhydrolyzed alkyl pyrophosphoric acid in solution in the diluent during stripping. The process comprises adding an oxidizing agent to the organic extractant and thereby oxidizing the tetravalent uranium to the +6 state in the organic extractant, and contacting the organic extractant containing the uranium in the +6 state with a stripping solution comprising an aqueous solution of an alkali metal or ammonium carbonate or hydroxide thereby stripping uranium from the organic extractant into the stripping solution. The resulting barren organic extractant containing substantially all of the unhydrolyzed alkyl pyrophosphoric acid dissolved in the diluent is separated from the stripping solution containing the stripped uranium, the barren extractant being suitable for recycle

Comparative study of buffered 50% glycolic acid (pH 3.0) + 0.5% salicylic acid solution vs Jessner's solution in patients with acne vulgaris.

Science.gov (United States)

In Jae, Jeong; Dong Ju, Hyun; Dong Hyun, Kim; Yoon, Moon Soo; Lee, Hee Jung

2017-11-21

Superficial chemical peels are frequently used in acne vulgaris treatment. Although glycolic acid (GA) has been widely used in clinical practice, its pH ranges from 0.08-2.75 and thus should be neutralized after application to avoid burns. To evaluate treatment efficacy and safety of chemical peeling using buffered 50% GA (pH 3.0) + 0.5% salicylic acid (SA) solution that does not need to be neutralized in the treatment of acne vulgaris compared to the conventional peeling using Jessner's solution. We performed a prospective, randomized, evaluator-blind, split-face clinical trial. Twenty patients were randomized by assigning one side of each patient's face to receive a 50% GA (pH 3.0) + 0.5% SA peel (GA side) and the other side to receive the Jessner's solution (Jessner's solution side). All patients underwent 2 sessions of treatment spaced 2 weeks apart. Lesion count, acne severity, subjective efficacy assessment, and side effects were evaluated. The total lesion count was significantly reduced for the GA and Jessner's solution sides (P  .05). The GA side had fewer side effects than the Jessner's solution side. The results of this study suggest that chemical peeling using the 50% GA (pH 3.0) + 0.5% SA solution can be as effective and convenient as the conventional peeling using Jessner's solution in the treatment of acne vulgaris and may show fewer adverse events than the conventional peeling. © 2017 Wiley Periodicals, Inc.

Extraction of americium from acid aqueous solutions by diethyl-2-hexyl-pyro-phosphoric acid

International Nuclear Information System (INIS)

Guillaume, Bernard

1971-02-01

After having outlined the interesting properties of americium and the difficulties of its recovery, the author reports the study of the mechanism of extraction of americium from acid aqueous solutions by using the diethyl-2hexyl-pyro-phosphoric acid. Several aspects are thus discussed: influence of concentration of H 2 DEHPP, influence of the acidity of the aqueous phase, saturation of extracting agent, influence of the diluting agent, complexing of americium, influence of other cations. In a second part, the author reports the application to the recovery of americium from effluents, and discusses the obtained results

Comparative radiosensitivity of amino acids during γ-radiolysis in aqueous solutions

International Nuclear Information System (INIS)

Duzhenkova, N.A.; Savich, A.V.

1977-01-01

The radiosensitivity of amino acids contained in proteins has been compared. The γ-radiolysis of aqueous solutions of amino acids has studied over a wide range of concentrations in the presence of air, the dose rate being 60 rad/sec, and the dose, 100 krad. Radiation-chemical yields of amino acid decay and ammonia accumulation are given. An increase in yields with amino acid concentration has been established. Assumptions concerning some peculiarities of the amino acid decay mechanism are made

Studies of the Tc oxidation states in humic acid solutions

International Nuclear Information System (INIS)

Wang Bo; Liu Dejun; Yao Jun

2010-01-01

The oxidation state is an important aspect of the speciation of Tc in groundwater that contained organic substances due to it control the precipitation, complexation, sorption and colloid formation behavior of the Tc under HWL geological disposal conditions. In present work, the oxidation states of Tc were investigated using the LaCl 3 coagulation method and solution extraction method in aqueous solutions in which the humic acid concentration range is from 0 to 20 mg L -1 and the Tc (Ⅶ) concentration range is about 10 -8 mol l -1 . The radiocounting of 99 Tc was determined using liquid scintillation spectrometry. The humic acid will influence the radiocounting ratio of 99 Tc apparently, however, the quenching effect can be restrained once keep the volume of the cocktail to about twenty times of the sample volume. The LaCl 3 coagulation methods were carried out for the investigation of Tc oxidation states in humic acid aqueous systems at about pH 8. The tetraphenylarsonium chloride (IPA)-chloroform extraction method was used also simultaneously to investigation the concentrations of Tc (Ⅳ) and Tc (Ⅶ) for the availability of the LaCl 3 precipitation method, and the experimental results demonstrate that tetravalent technetium and pertechnetate concentrations are well agreement with the LaCl 3 precipitation method. These two experimental results demonstrated that Tc (Ⅶ) is very stable in the Tc (Ⅶ)-humic acid system during a 350 days experimental period, and the Tc (Ⅳ) concentrations are very lower, that is indicate that there didn't oxidizing reactions between the Fluka humic acid and Tc (Ⅶ) in aqueous solutions under anaerobic conditions. That is means the presence of humic acids even in anaerobic groundwater is disadvantage for the retardance of radionuclides. (authors)

The reducibility of sulphuric acid and sulphate in aqueous solution

International Nuclear Information System (INIS)

Grauer, R.

1991-07-01

In connection with the Swedish project for final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister. A simple reaction between copper and sulphate is thermodynamically impossible, but copper can react to give copper sulphide if an additional electron donor such as iron(II) is available. The problem was extended to the more general question of the reducibility of sulphur(VI) in dilute aqueous solution. Chemical reduction of sulphate does not take place in dilute solution at temperatures below 100 o C. In experiments on the reduction of sulphates under hydrothermal conditions a reaction only takes place at temperatures above 275-300 o C. The oxidising action of sulphuric acid on metals becomes perceptible only at acid concentrations over 45-50%. In experiments on the cathodic reduction of 74% sulphuric acid the formation of hydrogen sulphide and elementary sulphur starts, depending on the current density, at 50-130 o C, and polarographic measurements suggest that the reducible species is not the hydrogen sulphate ion but molecular sulphuric acid. The resistance of copper to oxygen-free sulphuric acid up to a concentration of 60% is well-known. Numerous processes in industrial electrochemistry take place in sulphuric acid or sulphate electrolytes. The reversible metal/metal-sulphate electrodes of lead and cadmium are unstable relative to the corresponding metal sulphides. Nevertheless the reversible lead sulphate electrode does not fail from sulphide formation. All these facts confirm that sulphur(VI) in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be almost certainly be ruled out. (author) 5 figs., 85 refs

Applicability test of glass lining material for high-temperature acidic solutions of sulfuric acid in thermochemical water-splitting IS process

International Nuclear Information System (INIS)

Iwatsuki, Jin; Tanaka, Nobuyuki; Terada, Atsuhiko; Onuki, Kaoru; Watanabe, Yutaka

2010-01-01

A key issue for realizing the thermochemical IS process for hydrogen production is the selection of materials for working with high-temperature acidic solutions of sulfuric acid and hydriodic acid. Glass lining material is a promising candidate, which is composed of steel having good strength and glass having good corrosion resistance. Since the applicability of glass lining material depends strongly on the service condition, corrosion tests using glass used in glass lining material and heat cycle tests using glass lining piping were carried out to examine the possibility of using the glass lining material with high-temperature acidic solutions of sulfuric acid. It was confirmed that the glass lining materials exhibited sufficient corrosion resistance and heat resistance in high-temperature sulfuric acid of the IS process. (author)

Speciation of platinum(IV) in nitric acid solutions.

Science.gov (United States)

Vasilchenko, Danila; Tkachev, Sergey; Baidina, Iraida; Korenev, Sergey

2013-09-16

The speciation of platinum(IV) ions in nitric acid (6-15.8 M) solutions of H2[Pt(OH)6] has been studied by (195)Pt NMR and Raman spectroscopy. Series of aqua-hydroxo-nitrato complexes [Pt(L)(x)(NO3)(6-x)] (L = H2O or OH(-); x = 0, ..., 6) were found to exist in such solutions. The pair additivity model of chemical shifts and statistical theory were used to assign signals in NMR spectra to particular [Pt(L)(x)(NO3)(6-x)] species. Mononuclear hexanitratoplatinates(IV) have been isolated in solid state in substantial yield as pyridinium salt (PyH)2[Pt(NO3)6] and characterized by single-crystal X-ray diffraction. Aging of the platinum nitric acid solutions for more than 5-6 h results in oligomerization of [Pt(L)(x)(NO3)(6-x)] species and the formation of oligonuclear aqua-hydroxo-nitrato complexes with OH(-) and NO3(-) bridging ligands. Oligomeric platinum(IV) complexes with two and four nuclei were unambiguously detected by NMR on (195)Pt -enriched samples. Oligomers with even higher nuclearity were also detected. Dimeric anions [Pt2(μ-OH)2(NO3)8](2-) have been isolated as single crystals of tetramethylammonium salt and characterized by X-ray diffraction.

Investigations to explore interactions in (polyhydroxy solute + L-ascorbic acid + H2O) solutions at different temperatures: Calorimetric and viscometric approach

International Nuclear Information System (INIS)

Banipal, Parampaul K.; Sharma, Mousmee; Aggarwal, Neha; Banipal, Tarlok S.

2016-01-01

Highlights: • The hydrophilic-hydrophilic interactions predominate at low temperatures. • Enthalpy change for polyol is less exothermic than its parent saccharide. • Δ dil C o p,2,m values suggest structural increase in presence of L-ascorbic acid. • Solutes act as kosmotropes in L-ascorbic acid (aq) solutions as indicated by dB/dT. - Abstract: Isothermal titration micro-calorimeter has been used to measure the enthalpy change (q) of polyhydroxy solutes [(+)-D-xylose, xylitol, (+)-D-glucose, 2-deoxy-D-glucose, (+)-methyl-α-D-glucopyranoside, and (+)-maltose monohydrate] in water and in (0.05, 0.15, and 0.25) mol·kg −1 L-ascorbic acid (aq) solutions at (288.15, 298.15, 308.15, and 318.15) K. Limiting enthalpies of dilution (Δ dil H°) of these solutes were calculated from heat evolved/absorbed during calorimetric experiments. Further thermodynamic quantities such as limiting enthalpies of dilution of transfer (Δ tr Δ dil H°), change in heat capacity (Δ dil C o p,2,m ), and pair (h AB ) and triplet (h ABB ) enthalpic interaction coefficients were also calculated and used to explore the nature of interactions of solutes with cosolute (L-ascorbic acid). The Jones-Dole viscosity B-coefficients for (+)-D-xylose, xylitol, (+)-D-galactose, galactitol, (+)-D-glucose, 2-deoxy-D-glucose, (+)-methyl-α-D-glucopyranoside, and (+)-maltose monohydrate in water and in (0.05, 0.15, 0.25, and 0.35) mol·kg −1 L-ascorbic acid (aq) solutions have been determined from viscosity (η) data measured over temperature range (288.15–318.15) K and at pressure, P = 101.3 kPa. The temperature dependence of B-coefficients (dB/dT), and viscosity B-coefficients of transfer (Δ tr B) of solutes from water to cosolute have also been estimated. These parameters have been discussed in terms of structure-making (kosmotropic) or -breaking (chaotropic) behavior of solutes.

Mutagenicity of irradiated solutions of nuclei acid bases and nucleosides in Salmonella typhimurium

International Nuclear Information System (INIS)

Wilmer, J.; Schubert, J.

1981-01-01

Solutions of nucleic acid bases, nucleosides and a nucleotide, saturated with either N 2 , N 2 O or O 2 , were irradiated and tested for mutagenicity towards Salmonella typhimurium, with and without pre-incubation. Irradiated solutions of the nuclei acid bases were all non-mutagenic. Irradiated solutions of the nucleosides showed mutagenicity in S. typhimurium TA100 (pre-incubation assay). Generally, the mutagenicity followed the order: N 2 O > N 2 > O 2 . The results show that the formation of mutagenic radiolytic products is initiated by attack of mainly solutions of the nucleotide thymidine-5'-monophosphate, no mutagenicity could be detected. (orig.)

Extraction of Collagen from Chicken Feet with Various Acidic Solutions and Soaking Time

Directory of Open Access Journals (Sweden)

Prayitno Prayitno

2007-05-01

Full Text Available The objective of this research was to know the ability of various acidic solutions on dissolving collagen  chicken feet, with different soaked time.  Each acid 5 percent (v/v, collagen extraction was done by washing chicken feet and then cutted into small pieces and finally grinded.  Every 100 gram treatment was soaked in acetic acid (a1, citric acid (a2, lactic acid (a3 and hydrochloric acid (a4, for 12, 24 and 36 hours.  Precipitated collagen in the filtrate was 5 percent NaOH to reach the neutral pH (pH 7.  Collagen precipitate was separated by filtration usingfilter paper and then  rendement was calculated, HPLC was used to determin amino acid composition, and SDS-PAGE was use determin the type of collagen.  This experiment use factorial completely randomized design (CRD 4 x 3 and three time replication.   Result showed that lactic acid has highest capability to dissolve collagen, while citric acid the lowest.  Combination of acid solution and soaking time had significant (P<0.01 effect on dissolving collagen of chicken feet.  Extracted collagen in all acid solution, hassame amino acid, composition but different in percentage of amino acid molecules.  Collagen type in treatment combination was the same, but for soaking time of 36 hours revealed some peptide band.  Lactic acid had highest capability of collagen extraction in chicken feet than citric acid, acetic acid and hydrochloric acid with soaking time of 12, 24 and 36 hours.  It was estimated that extracted collagen can be grouped to type I consisted of two chain of a1. (Animal Production 9(2: 99-104 (2007   Key Words : Chicken feet, acids, soaking time, collagen

Long-term stability of earthen materials in contact with acidic tailings solutions

International Nuclear Information System (INIS)

Peterson, S.R.; Erikson, R.L.; Gee, G.W.

1982-11-01

The objectives of the studies documented in this report were to use experimental and geochemical computer modeling tools to assess the long-term environmental impact of leachate movement from acidic uranium mill tailings. Liner failure (i.e., an increase in the permeability of the liner material) was not found to be a problem when various acidic tailings solutions leached through liner materials for periods up to 3 years. On the contrary, materials that contained over 30% clay showed a decrease in permeability with time in the laboratory columns. The high clay materials tested appear suitable for lining tailings impoundment ponds. The decreases in permeability are attributed to pore plugging resulting from the precipitation of minerals and solids. This precipitation takes place due to the increase in pH of the tailings solution brought about by the buffering capacity of the soil. Geochemical modeling predicts, and x-ray characterization confirms, that precipitation of solids from solution is occurring in the acidic tailings solution/liner interactions studied. In conclusion the same mineralogical changes and contaminant reactions predicted by geochemical modeling and observed in laboratory studies were found at a drained evaporation pond (Lucky Mc in Wyoming) with a 4 year history of acid attack

Whole-body nitrogen and tyrosine metabolism in surgical patients receiving branched-chain amino acid solutions

International Nuclear Information System (INIS)

Desai, S.P.; Bistrian, B.R.; Moldawer, L.L.; Blackburn, G.L.

1985-01-01

Fifteen patients undergoing gastric bypass surgery for morbid obesity received preoperatively a standard crystalline amino acid solution containing 15.6% branched-chain amino acids. During the first five postoperative days, the patients were randomized to receive one of three amino acid solutions of different branched-chain amino acid content. Whole-body amino acid appearance and oxidation were estimated using a continuous intravenous infusion of L-(U- 14 C)-tyrosine preoperatively and on the third postoperative day. This study suggests that an adequate nitrogen intake of a balanced amino acid mixture, as well as a solution enriched with branched-chain amino acids, maintains protein homeostasis and supports protein synthesis similarly in well-nourished patients following major abdominal surgery. A diet containing only branched-chain amino acids in isomolar ratios was as effective at maintaining protein retention and whole-body protein synthesis and albumin renewal postoperatively when compared with a standard amino acid formula

Extraction of fission product rhodium from nitric acid solutions. 1

International Nuclear Information System (INIS)

Gorski, B.; Beer, M.; Russ, L.

1988-01-01

The extraction of noble metals from nitric acid solutions represents one problem of separating valueable substances from nuclear wastes in nuclear fuel reprocessing. Results of distribution experiments demonstrate the possibility of solvent extraction of rhodium using tertiary amines in presence of nitrite. Even short mixing times realize high distribution coefficients allowing quantitative separation from aqueous solutions. (author)

The recuperation of sulphuric acid out of contaminated solutions by electro electrodialysis

International Nuclear Information System (INIS)

Cattoir, S.

1997-05-01

The dismantling of a nuclear reactor results in large amounts of contaminated waste. The amount of waste is minimized by so-called decontamination processes. These decontamination processes result in decontaminated metal as well as contaminated effluents, containing acid and metal salts. Standard treatment of these effluents involves neutralisation of the acid using sodium hydroxide, resulting in the precipitation of hydroxides; and evaporation of the solvent. However, if the acid is extracted out of the decontamination effluents prior to neutralisation, this acid can be re-used in the decontamination process, substantially reducing the final waste. This report investigates the possibility of using Electro Electrodialysis (EED) for the extraction of 900 moles of sulphuric acid out of a 1 m 3 contaminated solution, containing 22 kg of ferrous, chromous, cerous and nickel ions and 1000 moles of sulphuric acid. EED removes acids out of acid/salts solutions, using an electrolyser equipped with an anionic membrane: the acid-anion is displaced by migration through the membrane while the proton is displaced by electrolysis. This report gives a full description of the technique, the lab-scale apparatus, the analyses involved in studying the technique on lab-scale or monitoring it on full scale, the choice of electrode and membrane and of process parameters such as temperature and current density. On lab scale, EED can displace 90% of the acid out of the acid/salt solution just described, at a current density as high as 0.14 A.cm -2 , at 50 degrees Celsius, if the cathode and the anode are of smoothed platina or of platinised titanium, and the anion selective membrane is the Neosepta AMH -membrane of Tokuyama. The study of EED still needs to be completed with a further study of metal deposition on the cathode, and a comparison of the technique to other (electro)membrane techniques

Mechanism of the extraction of nitric acid and water by organic solutions of tertiary alkyl-amines

International Nuclear Information System (INIS)

Gourisse, D.

1966-06-01

The micellar aggregation of tri-alkyl-ammonium nitrates in low polarity organic solvents has been verified by viscosity, conductivity and sedimentation velocity measurements. The aggregation depends upon the polarity of solvent, the length of the alkyl radicals and the organic concentration of the various constituents (tri-alkyl-ammonium nitrate, tri-alkyl-amine, nitric acid, water). The amine salification law has been established and the excess nitric acid and water solubilities in the organic solutions have been measured. Nitric acid and water are slightly more soluble in micellar organic solutions than in molecular organic solutions. A description of excess nitric acid containing tri-alkyl-ammonium nitrate solutions is proposed. (author) [fr

Effect of organic solvents on dissolution process of mechano-chemically activated molybdenum by inorganic acid solutions

International Nuclear Information System (INIS)

Shevtsova, I.Ya.; Chernyak, A.S.; Khal'zov, A.A.

1992-01-01

The process of chemical dissolution of mechanochemically activated and nonactivated molybdenite by inorganic acid solutions in certain organic solvents of different nature was considered. It is shown that the highest extraction of molybdenum in solution is achieved in the presence of nitric acid. The dissociation constant of the acid used in the given organic solvent does not affect molybdenite solubility. When dissolving molybdenite by solutions of nitric acid in carbonic acids, alcohols and esters, the solubility of the concentrate depends on the length of hydrocarbon chain of the organic solvent and dispersion degree of mineral source material

RECOVERY OF CARBOXYLIC ACIDS FROM AQUEOUS SOLUTIONS BY LIQUID-LIQUID EXTRACTION WITH A TRIISOOCTYLAMINE DILUENT SYSTEM

Directory of Open Access Journals (Sweden)

G. Malmary

2001-12-01

Full Text Available Tertiary alkylamines in solution with organic diluents are attractive extractants for the recovery of carboxylic acids from dilute aqueous phases. The aim of this study was to investigate the mechanism for extraction of organic acids from water by a long-chain aliphatic tertiary amine. In order to attain this objective, we studied the liquid-liquid equilibria between the triisooctylamine + 1-octanol + n-heptane system as solvent and an aqueous solution of an individual carboxylic acid such as citric, lactic and malic acids. The experiments showed that the partition coefficient for a particular organic acid depends on the kind of solute, notably when the acid concentration in the aqueous phase is low. A mathematical model, where both chemical association and physical distribution are taken into consideration, is proposed. The model suggests that the various complexes obtained between amine and organic acids contribute to the distribution of the solute between the coexisting phases in equilibrium.

Reactive solute transport in acidic streams

Science.gov (United States)

Broshears, R.E.

1996-01-01

Spatial and temporal profiles of Ph and concentrations of toxic metals in streams affected by acid mine drainage are the result of the interplay of physical and biogeochemical processes. This paper describes a reactive solute transport model that provides a physically and thermodynamically quantitative interpretation of these profiles. The model combines a transport module that includes advection-dispersion and transient storage with a geochemical speciation module based on MINTEQA2. Input to the model includes stream hydrologic properties derived from tracer-dilution experiments, headwater and lateral inflow concentrations analyzed in field samples, and a thermodynamic database. Simulations reproduced the general features of steady-state patterns of observed pH and concentrations of aluminum and sulfate in St. Kevin Gulch, an acid mine drainage stream near Leadville, Colorado. These patterns were altered temporarily by injection of sodium carbonate into the stream. A transient simulation reproduced the observed effects of the base injection.

Solution properties and taste behavior of lactose monohydrate in aqueous ascorbic acid solutions at different temperatures: Volumetric and rheological approach.

Science.gov (United States)

Sarkar, Abhijit; Sinha, Biswajit

2016-11-15

The densities and viscosities of lactose monohydrate in aqueous ascorbic acid solutions with several molal concentrations m=(0.00-0.08)molkg(-1) of ascorbic acid were determined at T=(298.15-318.15)K and pressure p=101kPa. Using experimental data apparent molar volume (ϕV), standard partial molar volume (ϕV(0)), the slope (SV(∗)), apparent specific volumes (ϕVsp), standard isobaric partial molar expansibility (ϕE(0)) and its temperature dependence [Formula: see text] the viscosity B-coefficient and solvation number (Sn) were determined. Viscosity B-coefficients were further employed to obtain the free energies of activation of viscous flow per mole of the solvents (Δμ1(0≠)) and of the solute (Δμ2(0≠)). Effects of molality, solute structure and temperature and taste behavior were analyzed in terms of solute-solute and solute-solvent interactions; results revealed that the solutions are characterized predominantly by solute-solvent interactions and lactose monohydrate behaves as a long-range structure maker. Copyright © 2016 Elsevier Ltd. All rights reserved.

Uranium extraction from sulfuric acid solution using anion exchange resin

International Nuclear Information System (INIS)

Sheta, M. E.; Abdel Aal, M. M.; Kandil, A. T.

2012-12-01

Uranium is currently recovered from sulfuric acid leach liquor using anion exchange resin as Amberlite IRA 402 (CT). This technology is based on fact that, uranium exists as anionic complexes. This takes place by controlling the pH of the solution, agitation time, temperature and resin to solution ratio (R/S). In this work, batch stirrer tank used for uranium extraction from sulfate medium and after extraction, elution process was done using 1M NaCl solution. After extraction and elution process, the resin was separated from the system and uranium was determined in the solution. (Author)

Copper complexation by tannic acid in aqueous solution

NARCIS (Netherlands)

Kraal, P.; Jansen, B.; Nierop, K.G.J.; Verstraten, J.M.

2006-01-01

The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon ((OC)/l was investigated in a nine-step titration experiment (Cu/oC molar ratio = 0.0030-0.0567). We differentiated between soluble and insoluble Cu species by 0.45 mu m

Trapping proton transfer intermediates in the disordered hydrogen-bonded network of cryogenic hydrofluoric acid solutions.

Science.gov (United States)

Ayotte, Patrick; Plessis, Sylvain; Marchand, Patrick

2008-08-28

A molecular-level description of the structural and dynamical aspects that are responsible for the weak acid behaviour of dilute hydrofluoric acid solutions and their unusual increased acidity at near equimolar concentrations continues to elude us. We address this problem by reporting reflection-absorption infrared spectra (RAIRS) of cryogenic HF-H(2)O binary mixtures at various compositions prepared as nanoscopic films using molecular beam techniques. Optical constants for these cryogenic solutions [n(omega) and k(omega)] are obtained by iteratively solving Fresnel equations for stratified media. Modeling of the experimental RAIRS spectra allow for a quantitative interpretation of the complex interplay between multiple reflections, optical interference and absorption effects. The evolution of the strong absorption features in the intermediate 1000-3000 cm(-1) range with increasing HF concentration reveals the presence of various ionic dissociation intermediates that are trapped in the disordered H-bonded network of cryogenic hydrofluoric acid solutions. Our findings are discussed in light of the conventional interpretation of why hydrofluoric acid is a weak acid revealing molecular-level details of the mechanism for HF ionization that may be relevant to analogous elementary processes involved in the ionization of weak acids in aqueous solutions.

Extraction of uranium from aqueous solution by phosphonic acid-imbedded polyurethane foam

International Nuclear Information System (INIS)

Katragadda, S.; Gesser, H.D.; Chow, A.

1997-01-01

Phenylphosphonic acid was imbedded into the matrix of the polyurethane foam during the fabrication process of the polymer. The extraction of uranium by phosphonic acid-imbedded polyurethane foam and blank polyurethane (i.e., foam without phosphonic acid functional groups) was investigated. Phosphonic acid-imbedded foam showed superior extractability of uranium from solutions with pH = 7.0 ± 1.5 over a wide range of temperatures. (author)

Control and monitoring of the localized corrosion of zirconium in acidic chloride solutions

International Nuclear Information System (INIS)

Fahey, J.; Holmes, D.; Yau, T.L.

1995-01-01

Zirconium in acidic chloride solutions which are contaminated with ferric or cupric cations is prone to localized corrosion. This tendency can be reduced by ensuring that the zirconium surface is clean and smooth. In this paper, the effect of surface condition on the localized corrosion of zirconium in acidic chloride solutions is predicted with potentiodynamic scans. These predictions are confirmed by weight loss tests on various combinations of surface finish and acid concentrations. A real time indication of localized corrosion is seen by monitoring the electrochemical noise produced between two similar electrodes immersed in an acidic chloride solutions. Electrochemical noise monitoring correlates well with the predictions from potentiodynamic and weight loss experiments. The electrochemical noise results show that while an elevated (more anodic) potential caused by ferric ion contamination may be a necessary condition for localized corrosion, it is not a sufficient condition: A smooth, clean zirconium surface reduces the localized corrosion of zirconium

Effect of Organic Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in Chloride Solutions

Energy Technology Data Exchange (ETDEWEB)

Carranza, R M; Giordano, C M; Rodr?guez, M A; Ilevbare, G O; Rebak, R B

2007-08-28

Electrochemical studies such as cyclic potentiodynamic polarization (CPP) and electrochemical impedance spectroscopy (EIS) were performed to determine the corrosion behavior of Alloy 22 (N06022) in 1M NaCl solutions at various pH values from acidic to neutral at 90 C. All the tested material was wrought Mill Annealed (MA). Tests were also performed in NaCl solutions containing weak organic acids such as oxalic, acetic, citric and picric. Results show that the corrosion rate of Alloy 22 was significantly higher in solutions containing oxalic acid than in solutions of pure NaCl at the same pH. Citric and picric acids showed a slightly higher corrosion rate, and acetic acid maintained the corrosion rate of pure chloride solutions at the same pH. Organic acids revealed to be weak inhibitors for crevice corrosion. Higher concentration ratios, compared to nitrate ions, were needed to completely inhibit crevice corrosion in chloride solutions. Results are discussed considering acid dissociation constants, buffer capacity and complex formation constants of the different weak acids.

Arsenic removal from acidic solutions with biogenic ferric precipitates.

Science.gov (United States)

Ahoranta, Sarita H; Kokko, Marika E; Papirio, Stefano; Özkaya, Bestamin; Puhakka, Jaakko A

2016-04-05

Treatment of acidic solution containing 5g/L of Fe(II) and 10mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7h, 96-98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pHremoves iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

Crack propagation behavior of Ti-5Ta alloy in boiling nitric acid solution

International Nuclear Information System (INIS)

Motooka, Takafumi; Kiuchi, Kiyoshi

1999-05-01

The crack propagation behavior of Ti-5Ta alloy both in boiling nitric acid solution and in air at room temperature has been investigated. The crack growth rate of Ti-5Ta alloy was measured as a function of the stress intensity factor range. After the tests, the fracture surface morphology was observed by a scanning electron microscope and the crystallographic orientation was examined by X-ray diffraction analysis. Difference in the crack growth behavior was not observed in both environments. The crack growth rate in boiling nitric acid solution was similar to that in air at room temperature. Moreover, the crystallographic orientation of Ti-5Ta alloy had little effect on the fatigue behavior, because this alloy does not have the susceptibility to SCC in nitric acid solution. (author)

Investigation of radiation-chemical behaviour of divalent palladium in perchloric acid solutions

International Nuclear Information System (INIS)

Vladimirova, M.V.; Kalinina, S.V.

1988-01-01

Gamma-radiolysis of divalent palladium in perchloric acid solutions is studied. Absorption spectra of intermediate palladium compounds formed in the irradiated solution are taken. The analysis of literature data as well as comparative analysis of the absorption spectra obtained under irradiation of palladium (2) perchloric acid solutions with absorption spectra of palladium chlorocomplexes allows to suppose that the mentioned compounds are chlorocomplexes of palladium (2) of different composition depending on HClO 4 concentration in the initial solution and absorbed radiation dose. Radiation-chemical reduction of palladium (2) up to metal is stated to take place in the whole studied range of initial concentrations of components of the system and dose rates. Kinetic dependences of metallic palladium formation are obtained. Values of radiation-chemical yields of metallic palladium formation depending on the initial concentrations of palladium (2) and perchloric acid are given. A mechanism of radiolytic reduction of palladium (2) in the investigated system is suggested based on the experimental data, and a theoretical value of the radiation-chemical yield of palladium (2) reduction being in a good agreement with experimentally found values is calculated

Radiation-chemical oxidation of neptunium in perchloric acid solutions

International Nuclear Information System (INIS)

Shilov, V.P.; Gusev, Yu.K.; Pikaev, A.K.; Stepanova, E.S.; Krot, N.N.

1979-01-01

The γ-radiation effect (at a dose rate of 5x10 16 eV/mlxs) on 1x10 -3 Np(6) and Np(5) perchloric acid solutions is studied. The output of Np(6) loss in aerated 0.001-0.005M HClO 4 solutions was 2.4 ions/100 eV. The output of Np(5) loss in solutions saturated with nitrous oxide was 2.1 ions/100 eV at pH-4. In aerated 0.1-1.0 M HClO 4 solutions in presence of XeO 4 the output of Np(5) loss grows from 6.6 to 13.5 ions/100 eV as (XeO 3 ) 0 increases from 1x10 -3 to 2x10 -2 M. Possible process mechanisms have been proposed

Adsorption of tannic acid from aqueous solution onto surfactant-modified zeolite

Energy Technology Data Exchange (ETDEWEB)

Lin, Jianwei, E-mail: jwlin@shou.edu.cn [College of Marine Science, Shanghai Ocean University, No. 999 Hucheng Huan Road, Pudong District, Shanghai 201306 (China); Zhan, Yanhui; Zhu, Zhiliang [State Key Laboratory of Pollution Control and Resource Reuse, Tongji University, Shanghai 200092 (China); Xing, Yunqing [College of Marine Science, Shanghai Ocean University, No. 999 Hucheng Huan Road, Pudong District, Shanghai 201306 (China)

2011-10-15

Graphical abstract: Surfactant-modified zeolites (SMZs) with various loadings of cetylpyridinium bromide (CPB) were used as adsorbents to remove tannic acid (TA) from aqueous solution. Highlights: {yields} Surfactant modified zeolites (SMZs) have a good tannic acid (TA) adsorption capacity. {yields} Adsorption capacity for SMZ with bilayer was relatively high at solution pH 3.5-7.0. {yields} Adsorption was well described by pseudo-second-order kinetic model. {yields} Adsorption fitted well with Langmuir, Redlich-Peterson and Sips isotherm models. {yields} Coexisting Cu(II) in aqueous solution resulted in markedly enhanced TA adsorption. - Abstract: Surfactant-modified zeolites (SMZs) with various loadings of cetylpyridinium bromide (CPB) were used as adsorbents to remove tannic acid (TA) from aqueous solution. The TA adsorption efficiencies for natural zeolite and various SMZs were compared. SMZ presented higher TA adsorption efficiency than natural zeolite, and SMZ with higher loading amount of CPB exhibited higher TA adsorption efficiency. The adsorption of TA onto SMZ as a function of contact time, initial adsorbate concentration, temperature, ionic strength, coexisting Cu(II) and solution pH was investigated. The adsorbents before and after adsorption were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), thermogravimetric analysis (TGA), and Fourier transform infrared (FT-IR) spectroscopy. The adsorption kinetics of TA onto SMZ with CPB bilayer coverage (SMZ-CBC) followed a pseudo-second-order model. The equilibrium adsorption data of TA onto SMZ-CBC were well represented by Langmuir, Redlich-Peterson and Sips isotherm models. The calculated thermodynamic parameters indicated that TA adsorption onto SMZ-CBC was spontaneous and exothermic. The TA adsorption capacity for SMZ-CBC slightly decreased with increasing ionic strength but significantly increased with increasing Cu(II) concentration. The TA adsorption

High-temperature extraction of rhenium from sulfuric acid solutions with trialkylamines

International Nuclear Information System (INIS)

Gladyhev, V.P.; Andreeva, N.N.; Kim, E.M.; Kovaleva, S.V.

1985-01-01

This paper attempts to determine the possibility of conducting high-temperature extraction of rhenium from sulfuric acid solutions with trialkylamines (TAA) using higher hydrocarbon-paraffin mixtures as the diluent of the extraction system. Substitution of kerosene by paraffin in the extraction system would permit decreasing the danger of fire and explosions during he extraction process. In extracting rhenium from industrial solutions with a melt of higher paraffins containing TAA and alcohols, the extraction system can be continously heated in heat exchangers through which washing sulfuric acid passes and then goes to the extractor. This permits utilizing the heat and decreases the temperature of the solutions for extraction to the optimum temperatures. Extraction of rhenium with a melt of trioctylamine in paraffin obeys the same mechanisms as high-temperature extraction of ruthenium (IV) by amines in kerosene and aromatic hydrocarbons

An investigation into the stability and sterility of citric acid solutions used for cough reflex testing.

Science.gov (United States)

Falconer, James R; Wu, Zimei; Lau, Hugo; Suen, Joanna; Wang, Lucy; Pottinger, Sarah; Lee, Elaine; Alazawi, Nawar; Kallesen, Molly; Gargiulo, Derryn A; Swift, Simon; Svirskis, Darren

2014-10-01

Citric acid is used in cough reflex testing in clinical and research settings to assess reflexive cough in patients at risk of swallowing disorders. To address a lack of knowledge in this area, this study investigated the stability and sterility of citric acid solutions. Triplicate solutions of citric acid (0.8 M) in isotonic saline were stored at 4 ± 2 °C for up to 28 days and analysed by high-performance liquid chromatography. Microbiological sterility of freshly prepared samples and bulk samples previously used for 2 weeks within the hospital was determined using a pour plate technique. Microbial survival in citric acid was determined by inoculating Staphylococcus aureus, Escherichia coli, or Candida albicans into citric acid solution and monitoring the number of colony-forming units/mL over 40 min. Citric acid solutions remained stable at 4 °C for 28 days (98.4 ± 1.8 % remained). The freshly prepared and clinical samples tested were sterile. However, viability studies revealed that citric acid solution allows for the survival of C. albicans but not for S. aureus or E. coli. The microbial survival study showed that citric acid kills S. aureus and E. coli but has no marked effect on C. albicans after 40 min. Citric acid samples at 0.8 M remained stable over the 4-week testing period, with viable microbial cells absent from samples tested. However, C. albicans has the ability to survive in citric acid solution if inadvertently introduced in practice. For this reason, in clinical and research practice it is suggested to use single-use aliquots prepared aseptically which can be stored for up to 28 days at 4 °C.

CO₂ Capture from Flue gas using Amino acid salt solutions

DEFF Research Database (Denmark)

Lerche, Benedicte Mai

to storage. Typical solvents for the process are based on aqueous solutions of alkanolamines, such as mono-ethanolamine (MEA), but their use implies economic disadvantages and environmental complications. Amino acid salt solutions have emerged as an alternative to the alkanolamines, partlybecause...... for measuring of CO2 solubility based on the semi-flow method. A validation study of CO2 solubility in aqueous solutions of MEA is presented. Chapter 5 focuses on the determination of the chemical compositions of the precipitations, which arise in the five amino acid salt solutions upon CO2 absorption...

The kinetics of oxidation of bilirubin and ascorbic acid in solution

Science.gov (United States)

Solomonov, A. V.; Rumyantsev, E. V.; Kochergin, B. A.; Antina, E. V.

2012-07-01

The results of a comparative study of the oxidation of bilirubin, ascorbic acid, and their mixture in aqueous solutions under the action of air oxygen and hydrogen peroxide are presented. The observed and true rate constants for the oxidation reactions were determined. It was shown that the oxidation of tetrapyrrole pigment occurred under these conditions bypassing the stage of biliverdin formation to monopyrrole products. Simultaneous oxidation of bilirubin and ascorbic acid was shown to be accompanied by the inhibition of ascorbic acid oxidation by bilirubin, whereas ascorbic acid itself activated the oxidation of bilirubin.

Gamma-irradiation of malic acid in aqueous solutions. [prebiotic significance

Science.gov (United States)

Negron-Mendoza, A.; Graff, R. L.; Ponnamperuma, C.

1980-01-01

The gamma-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the nonvolatile products. Thin layer chromatography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the gamma-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

Ginger extract as green corrosion inhibitor of mild steel in hydrochloric acid solution

Science.gov (United States)

Fidrusli, A.; Suryanto; Mahmood, M.

2018-01-01

Ginger extract as corrosion inhibitor from natural resources was studied to prevent corrosion of mild steel in acid media. Ginger rhizome was extracted to produce green corrosion inhibitor (G-1) while ginger powder bought at supermarket was also extract to form green corrosion inhibitor (G-2). Effectiveness of inhibitor in preventing corrosion process of mild steel was studied in 1.0 M of hydrochloric acid. The experiment of weight loss method and polarization technique were conducted to measure corrosion rate and inhibition efficiency of mild steel in solution containing 1.0 M of hydrochloric acid with various concentration of inhibitor at room temperature. The results showed that, the rate of corrosion dropped from 8.09 mmpy in solution containing no inhibitor to 0.72 mmpy in solution containing 150g/l inhibitor while inhibition efficiency up to 91% was obtained. The polarization curve in polarization experiments shows that the inhibition efficiency is 86% with high concentration of inhibitor. The adsorption of ginger extract on the surface of mild steel was observed by using optical microscope and the characterization analysis was done by using pH measurement method. When high concentration of green inhibitor in the acid solution is used, the pH at the surface of steel is increasing.

Features of obtaining malt with use of aqueous solutions of organic acids

Directory of Open Access Journals (Sweden)

O. Pivovarov

2017-12-01

Full Text Available Recently, the traditional formulations of essential food products are actively including malt – a valuable dietary product rich in extractives and hydrolytic enzymes, obtained by germination in artificially created conditions. Containing a full set of essential amino acids and a high saccharifying ability of malt, obtained from grain cereals, determines its wide use in the production of beer, alcohol, mono- and poly-malt extracts, bakery products, special types of flour, food additives, cereals, non-alcoholic beverages, lactic acid products and, in particular, in the production of natural coffee substitutes. However, the classical germination technology, which includes 2-3 days of soaking and 5-8 days of germination due to the considerable duration and laboriousness of the process, does not meet the requirements of modern technology and the constantly growing rates of industrial production, so this problem requires finding new and improving existing scientific and technical solutions. The features of malt production using organic acids of different concentrations are presented. The malt production technology has been analyzed and investigated. It includes washing, disinfection, air and water soaking of grains, germination and drying. The feature of the technology under investigation is using of aqueous solutions of butadiene, 3-pyridinecarboxylic acid and pteroylglutamic acid. The results of the inquiry of the effect of these organic acids on energy and the ability of germination of the grain are presented. The optimal values of concentrations of active substances in solutions are revealed. The influence of organic acids on the absorption of grain moisture has been investigated. It has been established that in comparison with the classical technology, the use of these acids as a growth stimulator can reduce the overall length of the reproduction process of the material from 1.5 to 2 times and increase the yield of flour grains in the batch of

Behaviours of trinitratonitrosyl complexes of ruthenium in dilute nitric acid solutions

Energy Technology Data Exchange (ETDEWEB)

Sugimoto, S [Radia Industry Co. Ltd., Takasaki (Japan)

1979-07-01

This study aimed to elucidate the protolysis and condensation processes of the Ru complexes in relation to the concentration of nitric acid. The compositions of the dissociated and undissociated complexes were determined by the extraction with tributyl phosphate (TBP) and absorption spectroscopy in order to follow the rather rapid protolysis reaction of the complexes. The test solutions were prepared by dissolving the freshly obtained complexes into 0.50 - 0.001 M nitric acid solutions. The amounts of the undissociated complexes were determined at different elapses of time in the test solutions. The protolysis became significant when the concentration was below 0.15 M, and the dissociation rate suddenly increased at this concentration. At the concentrations above 0.2 M, the absorption peak of the complexes at 480 nm survived even after 144 hours. But below 0.15 M, the formation of dissociation products by protolysis was observed after the disappearance of the absorption peak. The amount of dissociation products rapidly increased after the preparation of the test solution as the concentration decreased below 0.15 M.

Processes for working-up an aqueous fluosilicic acid solution

Directory of Open Access Journals (Sweden)

Alpha O. Toure

2012-11-01

Full Text Available Aqueous fluosilicic acid solutions were once considered to be only adverse by-products of phosphoric acid production, which required treatment to prevent ecosystem destruction when discharged into the sea. However, a range of chemicals can be generated by the transformation of this industrial waste product. Through experiments undertaken in the laboratory, we have shown the possibility of caustic soda production. Volumetric analysis showed caustic soda to be present as a 6%– 7%solution with yields of about 70% – 80%by weight. Two processes were investigated for the caustification of sodium fluoride, using different precipitates: sodium chloride and ethanol and are described by modelling caustification curves. The activation energies of precipitation determined by semi-empirical correlations showed that precipitation by ethanol (EA = 933.536 J/mol was more successful than precipitation by sodium chloride (EA = 7452.405 J/mol. Analyses performed on the precipitates highlighted compositions that are essential and useful constituents in the cement industry.

Cs separation from nitric acid solutions of radioactive waste

International Nuclear Information System (INIS)

Heckmann, K.; Pieronczyk, W.; Strnad, J.; Feldmaier, F.

1989-01-01

It was the objective of this study to selectively separate active caesium (Cs-134 and Cs-137) from acid radioactive waste solutions (especially MAW and HAWC). The following 'strategy' was designed for a separation process: synthesis of reagents which are acid-resistant and selective for caesium; precipitation of Cs + and separation of the precipitates by filtration or centrifugation or precipitation of Cs + and separation of the precipitates by flotation; caesium separation by liquid-liquid extraction. As precipitating agents, sodium tetraphenylborate (kalignost) and several of its fluorine derivatives were examined. (orig./RB) [de

Sorption of molybdenum by cellulose polyphosphate from acid solutions

International Nuclear Information System (INIS)

Luneva, N.K.; Oputina, A.G.; Ermolenko, I.N.

1985-01-01

The sorption of molybdenum on cellulose polyphosphate from acid solutions of ammonium molybdate depending on the phosphorus content in samples, concentration and pH of the solution, sorption time is studied. It is shown that a maximum molybdenum content on the cellulose samples with different phosphorus content is pointed out at an ammonium molybdate concentration 0.02 M. Saturation of the sorption curve is attained at molar ratio of adsrbed molybdenum to phosphorus 1:4. In case of small fillings the compound with molybdenum to phosphorus ratio 1:10 is formed

Characterisation of solution cast cellulose nanofibre – reinforced poly(lactic acid

Directory of Open Access Journals (Sweden)

2010-01-01

Full Text Available Cellulose nanofibres, 20 nm in diameter and 300 nm long, were prepared by acid hydrolysis of flax yarns. Composite films containing 2.5 and 5.0 wt% flax cellulose (FC fibres were prepared by solution casting of mixtures of poly(lactic acid (PLA solution and cellulose nanofibre suspension in chloroform. The resulting composite films and solution cast pure PLA film, with thickness of around 160 m, showed good transparency. For composites with 2.5 and 5.0 wt% FC, the tensile strength increased by 25 and 59% and tensile modulus by 42 and 47%, respectively, compared to pure PLA film. The composite film with 2.5 wt% FC combined high strength and ductility with tensile strength of 24.3 MPa and 70% elongation at break. Flax cellulose appeared to facilitate nucleation and subsequent crystallisation of PLA more effectively in the amorphous composites than in the crystalline composites.

THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

Science.gov (United States)

Brdicka, R

1936-07-20

1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

Corrosion of stainless steel in alcohol solutions of the simplest carboxylic acids

International Nuclear Information System (INIS)

Vigdorovich, V.I.; Korneeva, T.V.; Tsygankova, L.E.

1975-01-01

The behaviour of stainless Kh18N10T steel is considered in the methanol and ethanol solutions of formic and acetic acids, respectively. Consideration is given to the effect of the concentration (C) of the acid (0.01-1.00 N), water (0.1-20.0 mass.%) and temperature (room temperature, 40 and 60 deg C). Curves of anodic polarization were plotted. In the course of time in 1.0 and 0.5 N anhydrous methanol solutions of HCOOH at room temperature in the absence of the external anode current one can observe an increase in the electrode potential. Continued reduction of the formic acid concentration results in an improvement on the initial potential (psi) and a practical constancy of psi in time. It is shown that depending on the acid concentration the additions of water are capable of producing both a passivating and an activating effect. It is assumed that the growth in the length of the hydrocarbon radical of carboxylic acid promotes the adsorption displacement of water and alcohols from the metal surface and enhancement of the corrosion rate

Calorimetric investigation of solution heat of rare earth sulfates in acid solutions

International Nuclear Information System (INIS)

Vasin, S.K.; Babkin, A.G.; Kessler, Yu.M.

1978-01-01

To determine the thermodynamic characteristics of sulfates of rare elements an adiabatic airtight calorimeter has been developed, enabling measurement of minor heat effects of processes in aggressive media with an absolute error of about 5x10 -3 cal, the temperature sensitivity being no less than 2x10 -5 C 0 . The calorimeter is schematically represented. Measured with the aid of the calorimeter was the heat of dissolution of TiOSO 4 x2H 2 O in chloric acid solutions

Conformation of poly(γ-glutamic acid) in aqueous solution.

Science.gov (United States)

Muroga, Yoshio; Nakaya, Asami; Inoue, Atsuki; Itoh, Daiki; Abiru, Masaya; Wada, Kaori; Takada, Masako; Ikake, Hiroki; Shimizu, Shigeru

2016-04-01

Local conformation and overall conformation of poly(γ-DL-glutamic acid) (PγDLGA) and poly(γ-L-glutamic acid) (PγLGA) in aqueous solution was studied as a function of degree of ionization ε by (1) H-NMR, circular dichroism, and potentiometric titration. It was clarified that their local conformation is represented by random coil over an entire ε range and their overall conformation is represented by expanded random-coil in a range of ε > ε(*) , where ε(*) is about 0.3, 0.35, 0.45, and 0.5 for added-salt concentration of 0.02M, 0.05M, 0.1M, and 0.2M, respectively. In a range of ε acidic media. © 2015 Wiley Periodicals, Inc.

Coalescence of organic solutions in acid and metal extraction by tri-alkylamines; Demixtion des solutions organiques lors de l'extraction des acides et des metaux par les trialcoylamines

Energy Technology Data Exchange (ETDEWEB)

Blain, J [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1970-07-01

The formation of two layers with tri-alkylammonium salts solutions in low polarity diluents could be explained on the basis of settling of micelles. Light scattering and viscosity measurements reveal that micelles size increases rather sharply before coalescence. The existence of micelles in the solution has been confirmed by ultracentrifuge experiments. The behaviour of these solutions, in general, is similar to that of colloidal soap solutions. The various parameters which promote third phase formation are: anion size in the order of Cl{sup -} {approx} Br{sup -} < NO{sub 3} < ClO{sub 4}{sup -}; extraction of excess acid; metal cation size in the order of UO{sub 2}{sup ++} < Pu{sup 4+} {approx} Th{sup 4+}; decreasing in the length of the n-alkyl chain in the alkyl-ammonium salts; decreasing in diluent polarity. The above phenomenon could be explained on the basis of the affinity between alkylammonium salts and organic solvent. The composition of the three phases is independent of the initial amine concentration for a fixed acid and metal concentration. This has been verified experimentally and is in conformity with phase rule. (author) [French] La demixtion des solutions organiques de sels de trialcoyl-ammonium dans les solvants peu polaires est provoquee par la decantation des micelles presentes dans la solution. Nous avons montre par viscosimetrie et surtout par diffusion de la lumiere que les micelles grossissent de facon importante juste avant demixtion. Des experiences d'ultracentrifugation nous ont permis de confirmer la presence de micelles. Le comportement de ces solutions est analogue a celui des solutions colloidales de savons dans l'eau. Ainsi tous les parametres qui font decroitre la compatibilite du sel d'ammonium R{sub 3}NH+ oooX{sup -} avec le solvant organique favorisent l'agregation du sel et par consequent la demixtion, soient: l'extraction des anions de taille croissante Cl{sup -} {approx} Br{sup -} < NO{sub 3} < ClO{sub 4}{sup -}; l

Quenching characteristics of bathocuproinedisulfonic acid, disodium salt in aqueous solution and copper sulfate plating solution

Science.gov (United States)

Koga, Toshiaki; Hirakawa, Chieko; Takeshita, Michinori; Terasaki, Nao

2018-04-01

Bathocuproinedisulfonic acid, disodium salt (BCS) is generally used to detect Cu(I) through a color reaction. We newly found BCS fluorescence in the visible blue region in an aqueous solution. However, the fluorescence mechanism of BCS is not well known, so we should investigate its fundamental information. We confirmed that the characteristics of fluorescence are highly dependent on the molecular concentration and solvent properties. In particular, owing to the presence of the copper compound, the fluorescence intensity extremely decreases. By fluorescence quenching, we observed that a copper compound concentration of 10-6 mol/L or less could easily be measured in an aqueous solution. We also observed BCS fluorescence in copper sulfate plating solution and the possibility of detecting monovalent copper by fluorescence reabsorption.

Cesium absorption from acidic solutions using ammonium molybdophosphate on a polyacrylonitrile support (AMP-PAN)

International Nuclear Information System (INIS)

Miller, C.J.; Olson, A.L.; Johnson, C.K.

1995-01-01

Recent efforts at the Idaho Chemical Processing Plant (ICPP) have included evaluation of cesium removal technologies as applied to ICPP acidic radioactive waste streams. Ammonium molybdophosphate (AMP) immobilized on a polyacrylonitrile support (AMP-PAN) has been studied as an ion exchange agent for cesium removal from acidic waste solutions. Capacities, distribution coefficients, elutability, and kinetics of cesium-extraction have been evaluated. Exchange breakthrough curves using small columns have been determined from 1M HNO 3 and simulated waste solutions. The theoretical capacity of AMP is 213 g Cs/kg AMP. The average experimental capacity in batch contacts with various acidic solutions was 150 g Cs/kg AMP. The measured cesium distribution coefficients from actual waste solutions were 3287 mL/g for dissolved zirconia calcines, and 2679 mL/g for sodium-bearing waste. The cesium in the dissolved alumina calcines was analyzed for; however, the concentration was below analytical detectable limits resulting in inconclusive results. The reaction kinetics are very rapid (2-10 minutes). Cesium absorption appears to be independent of acid concentration over the range tested (0.1 M to 5 M HNO 3 )

Effect of humic acid on the underpotential deposition-stripping voltammetry of copper in acetic acid soil extract solutions at mercaptoacetic acid-modified gold electrodes

Energy Technology Data Exchange (ETDEWEB)

Herzog, Gregoire; Beni, Valerio; Dillon, Patrick H.; Barry, Thomas; Arrigan, Damien W.M

2004-05-24

Electrochemical measurements were undertaken for the investigation of the underpotential deposition-stripping process of copper at bare and modified gold electrodes in 0.11 M acetic acid, the first fraction of the European Union's Bureau Communautaire de References (BCR) sequential extraction procedure for fractionating metals within soils and sediments. Gold electrodes modified with mercaptoacetic acid showed higher sensitivity for the detection of copper than bare gold electrodes, both in the absence and in the presence of humic acid in acetic acid solutions, using the underpotential deposition-stripping voltammetry (UPD-SV) method. In the presence of 50 mg l{sup -1} of humic acid, the mercaptoacetic acid modified electrode proved to be 1.5 times more sensitive than the bare gold electrode. The mercaptoacetic acid monolayer formed on the gold surface provided efficient protection against the adsorption of humic acid onto the gold electrode surface. Variation of the humic acid concentration in the solution showed little effect on the copper stripping signal at the modified electrode. UPD-SV at the modified electrode was applied to the analysis of soil extract samples. Linear correlation of the electrochemical results with atomic spectroscopic results yielded the straight-line equation y ({mu}g l{sup -1}) = 1.10x - 44 (ppb) (R=0.992, n=6), indicating good agreement between the two methods.

Oxalic acid complexes: Promising draw solutes for forward osmosis (FO) in protein enrichment

KAUST Repository

Ge, Qingchun; Chung, Neal Tai-Shung

2015-01-01

Highly soluble oxalic acid complexes (OACs) were synthesized through a one-pot reaction. The OACs exhibit excellent performance as draw solutes in FO processes with high water fluxes and negligible reverse solute fluxes. Efficient protein enrichment was achieved. The diluted OACs can be recycled via nanofiltration and are promising as draw solutes.

Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1963-01-15

As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined.

Formation of amino acids by cobalt-60 irradiation of hydrogen cyanide solutions

Science.gov (United States)

Sweeney, M. A.; Toste, A. P.; Ponnamperuma, C.

1976-01-01

Experiments were conducted to study the pathway for the prebiotic origin of amino acids from hydrogen cyanide (HCN) under the action of ionizing radiation considered as an effective source of energy on the primitive earth. The irradiations were performed in a cobalt-60 source with a dose rate of 200,000 rad/hr. Seven naturally occurring amino acids are identified among the products formed by the hydrolysis of gamma-irradiated solutions of HCN: glycine, alanine, valine, serine, threonine, aspartic acid, and glutamic acid. The identity of these amino acids is established by gas chromatography and mass spectrometry. Control experiments provided evidence that the amino acids are not the result of contamination.

Raman spectrometric determination of Pu(VI) and Pu(V) in nitric acid solutions

International Nuclear Information System (INIS)

Gantner, E.; Freudenberger, M.; Steinert, D.; Ache, H.J.

1987-03-01

The determination of Pu(VI) in nitric acid solutions by spontaneous Laser Raman Spectrometry (LRS) was investigated and a calibration curve was established using U(VI) as internal standard. In addition, the concentrations of Pu(VI) and Pu(V) as a function of time were measured by this method in Pu(VI) solutions of different acidity containing H 2 O 2 as the reducing agent. In solutions which are intensely coloured by the presence of Ru(NO) complexes Pu(VI) can also be determined by LRS using a Kr + laser as excitation source. In future experiments, the study of the Pu(IV)-interaction with Ru using LRS and spectrophotometry as analytical techniques is therefore intended. (orig.) [de

Dynamic flow method to study the CO2 loading capacity of amino acid salt solutions

DEFF Research Database (Denmark)

Lerche, Benedicte Mai; Stenby, Erling Halfdan; Thomsen, Kaj

Due to a number of advantages amino acid salt solutions have emerged as alternatives to the alkanolamine solvents for the chemical absorption of CO2 from flue gas. The use of amino acids in CO2 capture is a bio-mimetic process, as it is similar to CO2 binding by proteins in the blood......, such as hemoglobin. Amino acid salt solutions have the same amine functionality as alkanolamines, and are thus expected to behave similar towards CO2 in flue gas. Despite rising interest, few studies have been performed so far on amino acids as CO2 absorbents....

Measurement of acidity and density of plutonium solutions

International Nuclear Information System (INIS)

Hofstetter, K.J.; Bowers, D.L.; Kemmerlin, R.P.

1978-01-01

The solutions were analyzed for acidity and total Pu concentration at ambient temperature while the density was determined at 25, 35, 45, and 60 0 C. From least squares fitting, it was found that the density could be computed to within 1% of the experimental value using the equation D = 1 + 0.0477[H + ] - 4.25 x 10 -3 [H + ] 2 + 1.477 x 10 -3 [Pu] - (T - 25)/1000

Simple method for preparation of secondary amides of phosphorylacetic acids and their use for actinide extraction and sorption from nitric acid solutions

International Nuclear Information System (INIS)

Artyushin, O.I.; Sharova, E.V.; Odinets, I.L.; Lenevich, S.V.; Mastruykova, T.A.; Morgalyuk, V.P.; Tananaev, I.G.; Pribylova, G.V.; Myasoedova, G.V.; Myasoedov, B.F.

2004-01-01

An effective method of synthesis of secondary alkylamides of phosphorylacetic acids (APA), based on amidation of ethyl esters of phosphorylacetic acids with primary aliphatic amines, was developed. Extraction of americium(III) complexes with APA solutions in dichloroethane and uranium(VI) sorption by sorbents with non-covalently fixed APA from nitric acid solutions were studied. In the course of americium(III) extraction there is no correlation between Am III distribution factor and APA structure, whereas during uranium(VI) sorption a dependence of U VI extraction degree on the complexing agent structure is observed [ru

Uranyl fluoride luminescence in acidic aqueous solutions

International Nuclear Information System (INIS)

Beitz, J.V.; Williams, C.W.

1996-01-01

Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 ± 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO 4 at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO 2 F 2 . Studies on the effect of added LiNO 3 or Na 2 WO 4 ·2H 2 O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF 6 content of WF 6 gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF 6

Effect of Na2CO3 degumming concentration on LiBr-formic acid-silk fibroin solution properties

Directory of Open Access Journals (Sweden)

Liu Zhi

2016-01-01

Full Text Available Salt-acid system has been proved to be of high efficiency for silk fibroin dissolution. Using salt-acid system to dissolve silk, native silk fibrils can be preserved in the regenerated solution. Increasing experiments indicate that acquirement of silk fibrils in solution is strongly associated with the degumming process. In this study, the effect of sodium carbonate degumming concentration on solution properties based on lithium bromide-formic acid dissolution system was systematically investigated. Results showed that the morphology transformation of silk fibroin in solution from nanospheres to nanofibrils is determined by sodium carbonate concentration during the degumming process. Solutions containing different silk fibroin structure exhibited different rheological behaviors and different electrospinnability, leading to different electrospun nanofibre properties. The results have guiding significance for preparation and application of silk fibroin solutions.

Study of precipitation behaviour of Mo and Zr in nitric acid solution

International Nuclear Information System (INIS)

Lin Cansheng; Wang Xiaoying; Zhang Chonghai

1992-01-01

The precipitation behaviour of Mo and Zr which depends on the concentrations of Mo, Zr, nitric acid and temperature is studied. Precipitation, post-precipitation and ultracentrifugation experiments are made at 100 deg C, 80 deg C, 60 deg C, 40 deg C and room temperatures in the range of 0.6-6.0 mol/1 nitric acid. The experimental feeds are made up of molybdenum labelled with 99 Mo, zirconium labelled with 95 Zr and nitric acid solution. The feed is allowed to stand at constant temperature for some time for the observation of precipitation behaviour. The filtered precipitate and ultracentrifuged liquid is to be measured with HP (Ge)-multichannel analyser in order to determine the content of Mo, Zr and their mole ration in the precipitate and to find out whether there is colloid in the liquid. The results show that the mixed solution of Mo and Zr can produce precipitate and post-precipitate in nitric acid. If the filtrated liquid is allowed to stand for some time, precipitate can be produced again, until the concentration of Mo and Zr in the feed is too low to form precipitate, such as 2.5 x 10 -3 mol/1. If the concentration of nitric acid is less than 4.0 mol/1, the precipitation is produced easily and more precipitate is formed. Precipitation is slower in solutions which are more than 4.0 mol/1 in HNO 3 . The mole-ratio of Mo to Zr in the precipitate is 2 to 1 and it is not dependent on that ratio in the system

Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process

Directory of Open Access Journals (Sweden)

Solange Alves da Silva COSTA

2015-01-01

Full Text Available The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA or 0.25% Proxitane Alpha (PA, for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001. However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one.

Stability of antimicrobial activity of peracetic acid solutions used in the final disinfection process.

Science.gov (United States)

Costa, Solange Alves da Silva; Paula, Olívia Ferreira Pereira de; Silva, Célia Regina Gonçalves E; Leão, Mariella Vieira Pereira; Santos, Silvana Soléo Ferreira dos

2015-01-01

The instruments and materials used in health establishments are frequently exposed to microorganism contamination, and chemical products are used before sterilization to reduce occupational infection. We evaluated the antimicrobial effectiveness, physical stability, and corrosiveness of two commercial formulations of peracetic acid on experimentally contaminated specimens. Stainless steel specimens were contaminated with Staphylococcus aureus, Escherichia coli, Candida albicans, blood, and saliva and then immersed in a ready peracetic acid solution: 2% Sekusept Aktiv (SA) or 0.25% Proxitane Alpha (PA), for different times. Then, washes of these instruments were plated in culture medium and colony-forming units counted. This procedure was repeated six times per day over 24 non-consecutive days. The corrosion capacity was assessed with the mass loss test, and the concentration of peracetic acid and pH of the solutions were measured with indicator tapes. Both SA and PA significantly eliminated microorganisms; however, the SA solution was stable for only 4 days, whereas PA remained stable throughout the experiment. The concentration of peracetic acid in the SA solutions decreased over time until the chemical was undetectable, although the pH remained at 5. The PA solution had a concentration of 500-400 mg/L and a pH of 2-3. Neither formulation induced corrosion and both reduced the number of microorganisms (p = 0.0001). However, the differences observed in the performance of each product highlight the necessity of establishing a protocol for optimizing the use of each one.

Relaxation to equilibrium following photoacid dissociation in mineral acids and buffer solutions

International Nuclear Information System (INIS)

Pines, D; Nibbering, E T J; Pines, E

2007-01-01

The relaxation to the dissociation equilibrium of a weak acid undergoing a transient pK a change in the presence of a strong mineral acid has been the subject of considerable interest both experimentally and theoretically. Here we compare this process with the analogue event taking place in a buffer solution of a weak carboxylic acid. The comparison has been performed in identical pH and ionic strength conditions and at a sufficiently short timescale where the buffer can only affect the weak acid relaxation by proton scavenging. Although the two relaxation processes have been found to differ in their temporal behaviour, they have both resulted in identical equilibrium amplitudes of the photoacid. This observation reassures the well-known chemical wisdom that pK a values measured in buffer solutions do not depend on the specific chemical reactivity of the buffer. We analyse the essentially many-body relaxation problem in terms of a re-normalized geminate recombination reaction which persists over longer times than the exponential relaxation to equilibrium of homogenously distributed populations of the reactants

Coagulation of some humic acid solutions by Moringa oleifera lam seeds: effect on chlorine requirement

Directory of Open Access Journals (Sweden)

L.M. Bawa

2001-12-01

Full Text Available Experiments were carried out to study humic acid solutions and surface waters coagulation by Moringa oleifera Lam seeds aqueous extract. High amounts of such extract (up to 10 g/L were required to clarify humic acid solutions whereas 0.5 g/L were used to remove 90% of initial turbidity of a surface water. The treatment of water with low turbidity (Moringa oleifera Lam seeds extract released a high amount of organic compounds in treated solutions leading to a high chlorine requirement.

The influence of temperature on the decomposition kinetics of peracetic acid in solutions

Directory of Open Access Journals (Sweden)

Kunigk L.

2001-01-01

Full Text Available Peracetic acid is a powerful sanitizer that has only recently been introduced in the Brazilian food industry. The main disadvantage of this sanitizer is its decomposition rate. The main purpose of this paper is to present results obtained in experiments carried out to study the decomposition kinetics of peracetic acid in aqueous solutions at 25, 35, 40 and 45 °C. The decompositon of peracetic acid is a first-order reaction. The decomposition rate constants are between 1.71x10-3 h -1 for 25 °C and 9.64x10-3 h-1 for 45 °C. The decomposition rate constant is affected by temperature according to the Arrhenius equation, and the activation energy for the decomposition of peracetic acid in aqueous solutions prepared from the commercial formulation used in this work is 66.20 kJ/mol.

Determination of acid ionization constants for weak acids by osmometry and the instrumental analysis self-evaluation feedback approach to student preparation of solutions

Science.gov (United States)

Kakolesha, Nyanguila

One focus of this work was to develop of an alternative method to conductivity for determining the acid ionization constants. Computer-controlled osmometry is one of the emerging analytical tools in industrial research and clinical laboratories. It is slowly finding its way into chemistry laboratories. The instrument's microprocessor control ensures shortened data collection time, repeatability, accuracy, and automatic calibration. The equilibrium constants of acetic acid, chloroacetic acid, bromoacetic acid, cyanoacetic acid, and iodoacetic acid have been measured using osmometry and their values compared with the existing literature values obtained, usually, from conductometric measurements. Ionization constant determined by osmometry for the moderately strong weak acids were in reasonably good agreement with literature values. The results showed that two factors, the ionic strength and the osmotic coefficient, exert opposite effects in solutions of such weak acids. Another focus of the work was analytical chemistry students solution preparation skills. The prevailing teacher-structured experiments leave little room for students' ingenuity in quantitative volumetric analysis. The purpose of this part of the study was to improve students' skills in making solutions using instrument feedback in a constructivist-learning model. After making some solutions by weighing and dissolving solutes or by serial dilution, students used the spectrophotometer and the osmometer to compare their solutions with standard solutions. Students perceived the instrument feedback as a nonthreatening approach to monitoring the development of their skill levels and liked to clarify their understanding through interacting with an instructor-observer. An assessment of the instrument feedback and the constructivist model indicated that students would assume responsibility for their own learning if given the opportunity. This study involved 167 students enrolled in Quantitative Chemical

Pulse Radiolysis of Adrenaline in Acid Aqueous Solutions

DEFF Research Database (Denmark)

Gohn, M.; Getoff, N.; Bjergbakke, Erling

1976-01-01

Pulse radiolysis of adrenaline in acid aqueous solutions (pH 1–3) was carried out. The rate constants for the reactions of adrenaline with H and OH were determined: k(H + adr.) = (0·9±0·1) × 109 dm3 mol−1s−1; k(OH + adr.) = (1·65±0·15) × 1010 dm3 mol−1s−1. The H-adduct of adrenaline has two λmax...

Coalescence of organic solutions in acid and metal extraction by tri-alkylamines

International Nuclear Information System (INIS)

Blain, J.

1970-01-01

The formation of two layers with tri-alkylammonium salts solutions in low polarity diluents could be explained on the basis of settling of micelles. Light scattering and viscosity measurements reveal that micelles size increases rather sharply before coalescence. The existence of micelles in the solution has been confirmed by ultracentrifuge experiments. The behaviour of these solutions, in general, is similar to that of colloidal soap solutions. The various parameters which promote third phase formation are: anion size in the order of Cl - ∼ Br - 3 4 - ; extraction of excess acid; metal cation size in the order of UO 2 ++ 4+ ∼ Th 4+ ; decreasing in the length of the n-alkyl chain in the alkyl-ammonium salts; decreasing in diluent polarity. The above phenomenon could be explained on the basis of the affinity between alkylammonium salts and organic solvent. The composition of the three phases is independent of the initial amine concentration for a fixed acid and metal concentration. This has been verified experimentally and is in conformity with phase rule. (author) [fr

EFFECT OF STABILIZERS ON THE CHEMICAL AND PHOTODEGRADATION OF ASCORBIC ACID IN AQUEOUS SOLUTION

Directory of Open Access Journals (Sweden)

Iqbal Ahmad

2016-06-01

Full Text Available Ascorbic acid (vitamin C is susceptible to light and air and forms various degradation products. A number of stabilizers have been used to study their effect on the degradation of ascorbic acid (AH2 in dark and light at pH 4.0 and 6.0 alone and in combination with citric and tartaric acids. The assay of AH2 in degraded solutions was performed by a specific UV spectrometric method. The degradation product of AH2 at pH 4.0 and 6.0 was identified as dehydroascorbic acid. The degradation of AH2 has been found to follow first-order kinetics. The apparent first-order rate constants, t90 and percent inhibition in rate in the presence of stabilizers and the second-order rate constants for the interaction of stabilizers with AH2 have been determined. The highest stabilizing effect on AH2 was found by sodium metabisulfite, followed by sodium sulfite, sodium bisulfate, sodium thiosulfate and thiourea. The pH of the solutions has also been found to influence the degradation of AH2 as the rates are higher at pH 6.0 compared to those of pH 4.0, probably due to the ionization of AH2. A synergistic effect has been observed when citric or tartaric acid was added to the solutions containing stabilizers where citric acid showed comparatively better effect.

Intramolecular synergistic effect of glutamic acid, cysteine and glycine against copper corrosion in hydrochloric acid solution

International Nuclear Information System (INIS)

Zhang Daquan; Xie Bin; Gao Lixin; Cai Qirui; Joo, Hyung Goun; Lee, Kang Yong

2011-01-01

The corrosion protection of copper by glutamic acid, cysteine, glycine and their derivative (glutathione) in 0.5 M hydrochloric acid solution has been studied by the electrochemical impedance spectroscopy and cyclic voltammetry. The inhibition efficiency of the organic inhibitors on copper corrosion increases in the order: glutathione > cysteine > cysteine + glutamic acid + glycine > glutamic acid > glycine. Maximum inhibition efficiency for cysteine reaches about 92.9% at 15 mM concentration level. The glutathione can give 96.4% inhibition efficiency at a concentration of 10 mM. The molecular structure parameters were obtained by PM3 (Parametric Method 3) semi-empirical calculation. The intramolecular synergistic effect of glutamic acid, cysteine and glycine moieties in glutathione is attributed to the lower energy of the lowest unoccupied molecular orbital (E LUMO ) level and to the excess hetero-atom adsorption centers and the bigger coverage on the copper surface.

Influence of Concentration and Agitation of Sodium Hypochlorite and Peracetic Acid Solutions on Tissue Dissolution.

Science.gov (United States)

Tanomaru-Filho, Mário; Silveira, Bruna Ramos Franco; Martelo, Roberta Bosso; Guerreiro-Tanomaru, Juliane Maria

2015-11-01

To evaluated the tissue dissolution of sodium hypochlorite (NaOCl) and peracetic acid (PA) solutions at different concentrations, with or without ultrasonic agitation. The following solutions were analyzed: 2.5% NaOCl, 0.5, 1 and 2% PA, 1% PA associated with 6.5% hydrogen peroxide (HP) and saline. Fragments of bovine pulp tissue with 25 ± 2g mg were immersed into test tubes containing 4 mL of the solutions for 10 minutes. In the groups with agitation, pulp tissues were submitted to 2 cycles of 1 minute of ultrasonic agitation. The specimens were weighed after the removal from the solutions. The percentage of mass loss was calculated according to the difference of mass before and after exposure to solutions. Data were submitted to ANOVA and Tukey tests (p Peracetic acid solution has pulp tissue dissolution. However, this ability is lower than 2.5% NaOCl solution. The sodium hypochlorite solution shows higher ability to dissolve tissue than PA.

Spectrophotometric determination of uranium and plutonium in nitric acid solutions at their co-presence

International Nuclear Information System (INIS)

Levakov, B.I.; Mishenev, V.B.; Nezgovorov, N.Yu.; Ryazanova, G.K.; Timofeev, G.A.

1986-01-01

The method of spectrophotometric determination of uranium (6) and plutonium (4) in nitric acid solutions is described. Uranium is determined by light absorption of the complex with arsenazo 3 in 0.05 mol/l nitric acid at λ=654 nm, plutonium - by light absorption of the complex with xylenol orange in 0.1 mol/l nitric acid at λ=540 nm. To disguise plutonium, tetravalent and certain trivalent elements DTPA is introduced into photometered solution for uranium determination. The relative root-mean square deviation of determination results does not exceed 0.03 in uranium concenration ranges 0.5-5 μg/ml, of plutonium -1-3 μg/ml

Behaviour of Type 316 steel in acidic sulphate solutions at 300-3500C

International Nuclear Information System (INIS)

Newman, J.F.

1987-11-01

Most cation resin beds in service in CEGB power stations, and particularly those in AGR stations, are regenerated with sulphuric acid. Slippage results in trace levels of sulphate passing into the boilers. Previous work has shown that in once-through boilers, feedwater containing 2 μg kg -1 of sulphate could concentrate at localized dry-out sites to form solutions having from 0.1 to 7 wt% of solute. It has been shown also that if the sulphate was present in an acidic solution and it were to be in contact with Type 316 austentitic superheater steel, then intergranular corrosion and intergranular cracking could occur. Previous data, including some unreported results, are tabulated and discussed. The current work had two main objectives. The first was to extend the previous investigations to examine a wider range of acidic sulphate concentrations (as indicated by calculations on the concentration of solute in feedwater), the influence of environment pH, and the effect of sensitization of specimens. The second objective was primarily concerned with elucidating the causes of scatter in the results. This involved examining the influence of electrode potential, the ageing characteristics of the environment, and the method of applying stress to the specimens. (author)

A bibliographical review on the radiolysis of uranyl nitrate solutions in nitric acid medium

International Nuclear Information System (INIS)

Siri, Sandra; Mondino, Angel V.

2004-01-01

A bibliographical study on the effects of ionizing radiation on uranyl nitrate solutions in nitric acid medium was performed, and the state of knowledge on this subject is presented. The main experimental and theoretical results on water, nitric acid and uranium solutions radiolysis are reviewed and critically evaluated. This paper provides a collection of references as an aid to the development of practical applications, and to stimulate new research on fundamental processes in these systems. (author) [es

Comparative study of polypyrrole films electrosynthesized in alkaline and acid solutions

International Nuclear Information System (INIS)

Lehr, I.L.; Quinzani, O.V.; Saidman, S.B.

2009-01-01

The influence of the pH of electropolymerization solutions on the properties of polypyrrole films has been studied using potentiodynamic techniques and faradaic impedance spectroscopy. Scanning electron microscopy (SEM), IR and Raman spectroscopies, thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) were also used for products characterization. Results indicate that, contrary to what happen with the polymer electrogenerated in acid solutions, the films prepared in alkaline media are stable and present good electrochemical activity in basic solutions. Possible explanations for the observed differences are discussed and it is proposed that the pH of electropolymerization medium directly affects chains organization. Electrosynthesis in solutions of increased basicity results in a more compact and closed polymer structure.

Photometric estimation of plutonium in product solutions and acid waste solutions using flow injection analysis technique

International Nuclear Information System (INIS)

Dhas, A.J.A.; Dharmapurikar, G.R.; Kumaraguru, K.; Vijayan, K.; Kapoor, S.C.; Ramanujam, A.

1995-01-01

Flow injection analysis technique is employed for the measurement of plutonium concentrations in product nitrate solutions by measuring the absorbance of Pu(III) at 565 nm and of Pu(IV) at 470 nm, using a Metrohm 662 photometer, with a pyrex glass tube of 2 nm (ID) inserted in the light path of the detector serving as a flow cell. The photometer detector never comes in contact with radioactive solution. In the case of acid waste solutions Pu is first purified by extraction chromatography with 2-ethyl hexyl hydrogen 2 ethyl hexyl phosphonate (KSM 17)- chromosorb and the Pu in the eluate in complexed with Arsenazo III followed by the measured of absorbance at 665 nm. Absorbance of reference solutions in the desired concentration ranges are measured to calibrate the system. The results obtained agree with the reference values within ±2.0%. (author). 3 refs., 1 tab

On solubility of perchloric (periodic) acid and α-cyanacetanmide in aqueous solutions at 25 deg C

International Nuclear Information System (INIS)

Omarova, R.A.; Balysbekov, S.M.; Erkasov, R.Sh.; Nikolenko, O.N.

1996-01-01

Acid-base interaction within perchloric (periodic) acid-α-cyanacetamide-water systems in studied by method of solubility under isothermal conditions at 25 deg C. Solubility regularities of crystalline α-cyanacetamide in perchloric and periodic acid solutions are determined, the concentration limits of formation of a new solid phase-tris(α-cyanacetamide) perchlorate within perchloric acid-α-cyanacetamide-water system are determined. The compound is identified by means of chemical and X-ray phase analyses, its density and melting temperature are determined. Iodic acid and α-cyanacetamide water solution base system is shown to belong to a simple eutonic type. 2 refs., 3 figs., 2 tabs

High-Yield Production of Levulinic Acid from Pretreated Cow Dung in Dilute Acid Aqueous Solution

Directory of Open Access Journals (Sweden)

Jialei Su

2017-02-01

Full Text Available Agricultural waste cow dung was used as feedstock for the production of a high value–added chemical levulinic acid (LA in dilute acid aqueous solutions. A high LA yield of 338.9 g/kg was obtained from the pretreated cow dung, which was much higher than that obtained from the crude cow dung (135 g/kg, mainly attributed to the breakage of the lignin fraction in the lignocellulose structure of the cow dung by potassium hydroxide (KOH pretreatment, and thus enhanced the accessibility of cow dung to the acid sites in the catalytic reaction. Meanwhile, another value-added chemical formic acid could be obtained with a yield of ca. 160 g/kg in the process, implying a total production of ca. 500 g/kg yield for LA and formic acid from the pretreated cow dung with the proposed process. The developed process was shown to be tolerant to high initial substrate loading with a satisfied LA yield. This work provides a promising strategy for the value-increment utilization of liglocellulosic agricultural residues.

Development of Temperature Control Solutions for Non-Instrumented Nucleic Acid Amplification Tests (NINAAT

Directory of Open Access Journals (Sweden)

Tamás Pardy

2017-06-01

Full Text Available Non-instrumented nucleic acid amplification tests (NINAAT are a novel paradigm in portable molecular diagnostics. They offer the high detection accuracy characteristic of nucleic acid amplification tests (NAAT in a self-contained device, without the need for any external instrumentation. These Point-of-Care tests typically employ a Lab-on-a-Chip for liquid handling functionality, and perform isothermal nucleic acid amplification protocols that require low power but high accuracy temperature control in a single well-defined temperature range. We propose temperature control solutions based on commercially available heating elements capable of meeting these challenges, as well as demonstrate the process by which such elements can be fitted to a NINAAT system. Self-regulated and thermostat-controlled resistive heating elements were evaluated through experimental characterization as well as thermal analysis using the finite element method (FEM. We demonstrate that the proposed solutions can support various NAAT protocols, as well as demonstrate an optimal solution for the loop-mediated isothermal amplification (LAMP protocol. Furthermore, we present an Arduino-compatible open-source thermostat developed for NINAAT applications.

Density, viscosity, and N2O solubility of aqueous amino acid salt and amine amino acid salt solutions

International Nuclear Information System (INIS)

Aronu, Ugochukwu E.; Hartono, Ardi; Svendsen, Hallvard F.

2012-01-01

Highlights: ► Density of amino acid salt and amine amino acid salt. ► Viscosity of amino acid salt and amine amino acid salt. ► Henry’s law constant/N 2 O solubility of amino acid salt and amine amino acid salt. ► Schumpe model. Correlations for density, viscosity, and N 2 O solubility. - Abstract: Physicochemical properties of aqueous amino acid salt (AAS), potassium salt of sarcosine (KSAR) and aqueous amine amino acid salt (AAAS), 3-(methylamino)propylamine/sarcosine (SARMAPA) have been studied. Densities of KSAR were measured for sarcosine mole fraction 0.02 to 0.25 for temperature range 298.15 K to 353.15 K, the viscosities were measured for 0.02 to 0.10 mole fraction sarcosine (293.15 K to 343.15 K) while the N 2 O solubilities were measured from 0.02 to 0.10 mole fraction sarcosine solutions (298.15 K to 363.15 K). Densities of SARMAPA were measured for sarcosine mole fraction 0.02 to 0.23 for temperature range (298.15 K to 353.15 K), viscosities were measured for 0.02 to 0.16 mole fraction sarcosine (293.15 K to 343.15 K) while the N 2 O solubilities were measured from 0.02 to 0.16 mole fraction sarcosine solutions (298.15 K to 343.15 K). Experimental results were correlated well with empirical correlations and N 2 O solubility results for KSAR were predicted adequately by a Schumpe model. The solubilities of N 2 O in AAS and AAAS are significantly lower than values for amines. The solubilities vary as: amine > AAAS > AAS.

Nanostructural characterization of large-scale porous alumina fabricated via anodizing in arsenic acid solution

Energy Technology Data Exchange (ETDEWEB)

Akiya, Shunta; Kikuchi, Tatsuya, E-mail: kiku@eng.hokudai.ac.jp; Natsui, Shungo; Suzuki, Ryosuke O.

2017-05-01

Highlights: • Anodic porous alumina was formed in an arsenic acid solution. • Potential difference (voltage) anodizing at 340 V was achieved. • The porous alumina was slightly ordered under the appropriate conditions. • Pore sealing behavior was not observed in boiling distilled water. • The porous alumina exhibits a white photoluminescence emission under UV irradiation. - Abstract: Anodizing of aluminum in an arsenic acid solution is reported for the fabrication of anodic porous alumina. The highest potential difference (voltage) without oxide burning increased as the temperature and the concentration of the arsenic acid solution decreased, and a high anodizing potential difference of 340 V was achieved. An ordered porous alumina with several tens of cells was formed in 0.1–0.5 M arsenic acid solutions at 310–340 V for 20 h. However, the regularity of the porous alumina was not improved via anodizing for 72 h. No pore sealing behavior of the porous alumina was observed upon immersion in boiling distilled water, and it may be due to the formation of an insoluble complex on the oxide surface. The porous alumina consisted of two different layers: a hexagonal alumina layer that contained arsenic from the electrolyte and a pure alumina honeycomb skeleton. The porous alumina exhibited a white photoluminescence emission at approximately 515 nm under UV irradiation at 254 nm.

The response of soil solution chemistry in European forests to decreasing acid deposition.

Science.gov (United States)

Johnson, James; Graf Pannatier, Elisabeth; Carnicelli, Stefano; Cecchini, Guia; Clarke, Nicholas; Cools, Nathalie; Hansen, Karin; Meesenburg, Henning; Nieminen, Tiina M; Pihl-Karlsson, Gunilla; Titeux, Hugues; Vanguelova, Elena; Verstraeten, Arne; Vesterdal, Lars; Waldner, Peter; Jonard, Mathieu

2018-03-31

Acid deposition arising from sulphur (S) and nitrogen (N) emissions from fossil fuel combustion and agriculture has contributed to the acidification of terrestrial ecosystems in many regions globally. However, in Europe and North America, S deposition has greatly decreased in recent decades due to emissions controls. In this study, we assessed the response of soil solution chemistry in mineral horizons of European forests to these changes. Trends in pH, acid neutralizing capacity (ANC), major ions, total aluminium (Al tot ) and dissolved organic carbon were determined for the period 1995-2012. Plots with at least 10 years of observations from the ICP Forests monitoring network were used. Trends were assessed for the upper mineral soil (10-20 cm, 104 plots) and subsoil (40-80 cm, 162 plots). There was a large decrease in the concentration of sulphate (SO42-) in soil solution; over a 10-year period (2000-2010), SO42- decreased by 52% at 10-20 cm and 40% at 40-80 cm. Nitrate was unchanged at 10-20 cm but decreased at 40-80 cm. The decrease in acid anions was accompanied by a large and significant decrease in the concentration of the nutrient base cations: calcium, magnesium and potassium (Bc = Ca 2+  + Mg 2+  + K + ) and Al tot over the entire dataset. The response of soil solution acidity was nonuniform. At 10-20 cm, ANC increased in acid-sensitive soils (base saturation ≤10%) indicating a recovery, but ANC decreased in soils with base saturation >10%. At 40-80 cm, ANC remained unchanged in acid-sensitive soils (base saturation ≤20%, pHCaCl2 ≤ 4.5) and decreased in better-buffered soils (base saturation >20%, pHCaCl2 > 4.5). In addition, the molar ratio of Bc to Al tot either did not change or decreased. The results suggest a long-time lag between emission abatement and changes in soil solution acidity and underline the importance of long-term monitoring in evaluating ecosystem response to decreases in deposition. © 2018 John Wiley & Sons

Interaction of sodium monoborate and boric acid with some mono- and disaccharides in aqueous solutions (from data on isomolar solutions method)

International Nuclear Information System (INIS)

Shvarts, E.M.; Ignash, R.T.; Belousova, R.G.

2000-01-01

Interaction of sodium monoborate Na[B(OH) 4 ] and boric acid with D-glucose, D-fructose, D-saccharose and D-lactose in aqueous solution depending on the solution total concentration is studied through the method of isomolar solutions with application of conductometry and polarimetry. It is shown by the D-glucose and D-fructose examples that the method of isomolar solutions leads to results compatible with the data obtained by other methods and it may be applied to other saccharides [ru

Anodic stripping voltammetric determination of heavy metals in solutions containing humic acids

International Nuclear Information System (INIS)

Labuda, J.; Saur, D.; Neeb, R.

1994-01-01

Various simultaneous effects of humic acids on the current and potential of differential pulse anodic stripping peaks of copper, lead, cadmium and zinc in weakly alkaline and acidic (pH 2) solutions have been investigated and interpreted with regard to metal complexation and the adsorption of humic acid on the mercury electrode. The applicability of the standard additions method for metal quantitation and the experimental conditions for UV-photolysis with a high-pressure mercury lamp have been examined in model as well as real water samples. (orig.)

Volumetric and viscometric studies of amino acids in L-ascorbic acid aqueous solutions at T = (293.15 to 323.15) K

International Nuclear Information System (INIS)

Jiang, Xiaofeng; Zhu, Chunying; Ma, Youguang

2014-01-01

Graphical abstract: The densities and viscosities of L-alanine in L-ascorbic acid aqueous solutions at T = 293.15 K. Highlights: • Densities and viscosities of five amino acids in L-ascorbic acid aqueous solutions were measured. • Based on the experimental data, a series of volumetric and viscometric parameters were calculated. • The group additivity analysis has been applied to analyze the V φ 0 and B-coefficients. -- Abstract: Densities and viscosities of glycine, L-alanine, L-valine, L-threonine and L-arginine in aqueous solutions of (0.0, 0.1, 0.2, 0.3 and 0.4) mol · kg −1 L-ascorbic acid have been measured at T = (293.15, 303.15, 313.15 and 323.15) K under atmospheric pressure. The apparent molar volumes (V φ ), limiting partial molar volumes (V φ 0 ), limiting partial molar volumes of transfer (Δ tr V φ 0 ) and limiting partial molar expansibilities (E 2 0 ) were computed by densities. The extended Jones–Dole equation was used to correlate the viscosities in order to obtain viscosity B-coefficients and the free energies of activation per mole of solvent (Δμ 1 0≠ ) and solute (Δμ 2 0≠ ) were also calculated. The contributions of zwitterionic end group (NH 3 + , COO − ), CH 2 group, OH group and CNHNHNH 2 group to V φ 0 and viscosity B-coefficients were obtained through the group additivity analysis

Boron removal from aqueous solutions by activated carbon impregnated with salicylic acid

International Nuclear Information System (INIS)

Celik, Z. Ceylan; Can, B.Z.; Kocakerim, M. Muhtar

2008-01-01

In this study, the removal of boric acid from aqueous solution by activated carbon impregnated with salicylic acid was studied in batch system. pH, adsorbent amount, initial boron concentration, temperature, shaking rate and salicylic acid film thickness were chosen as parameters. Boron removal efficiencies increased with increasing adsorbent amount, temperature and pH, decreasing initial boron concentration. As thickness of salicylic acid film on activated carbon becomes thin up to 0.088 nm, the efficiency increased, and then, the efficiency decreased with becoming thinner than 0.088 nm of salicylic acid film. Shaking rate was no effect on removal efficiency. In result, it was determined that the use of salicylic acid as an impregnant for activated carbon led to the increase of the amount of boron adsorbed. A lactone ring, being the most appropriate conformation, forms between boric acid and -COOH and -OH groups of salicylic acid

Boron removal from aqueous solutions by activated carbon impregnated with salicylic acid

Energy Technology Data Exchange (ETDEWEB)

Celik, Z. Ceylan [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey)], E-mail: zcelik@atauni.edu.tr; Can, B.Z. [Department of Environmental Engineering, Atatuerk University, Faculty of Engineering, Erzurum (Turkey); Kocakerim, M. Muhtar [Department of Chemical Engineering, Atatuerk University, Faculty of Engineering, 25240 Erzurum (Turkey)

2008-03-21

In this study, the removal of boric acid from aqueous solution by activated carbon impregnated with salicylic acid was studied in batch system. pH, adsorbent amount, initial boron concentration, temperature, shaking rate and salicylic acid film thickness were chosen as parameters. Boron removal efficiencies increased with increasing adsorbent amount, temperature and pH, decreasing initial boron concentration. As thickness of salicylic acid film on activated carbon becomes thin up to 0.088 nm, the efficiency increased, and then, the efficiency decreased with becoming thinner than 0.088 nm of salicylic acid film. Shaking rate was no effect on removal efficiency. In result, it was determined that the use of salicylic acid as an impregnant for activated carbon led to the increase of the amount of boron adsorbed. A lactone ring, being the most appropriate conformation, forms between boric acid and -COOH and -OH groups of salicylic acid.

Interactions of hydrazine, ferrous sulfamate, sodium nitrite, and nitric acid in nuclear fuel processing solutions

International Nuclear Information System (INIS)

Gray, L.W.

1977-03-01

Hydrazine and ferrous sulfamate are used as reductants in a variety of nuclear fuel processing solutions. An oxidant, normally sodium nitrite, must frequently be added to these nitric acid solutions before additional processing can proceed. The interactions of these four chemicals have been studied under a wide variety of conditions using a 2/sup p/ factorial experimental design to determine relative reaction rates for desired reactions and side reactions. Evidence for a hydrazine-stabilized, sulfamic acid--nitrous acid intermediate was obtained; this intermediate can hydrolyze to ammonia or decompose to nitrogen. The oxidation of Fe 2+ by NO 2 - was shown to proceed at about the same rate as the scavenging of NO 2 - by sulfamic acid. Various side reactions are discussed

Potentiometric determination of free nitric-acid in trilaurylamine solutions containing plutonium nitrate

International Nuclear Information System (INIS)

Perez, J.J.; Saey, J.C.

1965-01-01

A potentiometric method of determination of the free nitric acid in trilaurylamine solutions containing plutonium or thorium nitrates is described. The potentiometric titration is carried out in a mixture of benzene and 1,2-dichloro ethane with a standard solution of trilaurylamine as the titrant. When thorium nitrate is present the metal complex is not dissociated then the titration has a single end-point. In the case of plutonium nitrate the partial dissociation of the plutonium complex corresponds to a second point. The experimental error in duplicate analyses of 50 samples is about 1 per cent for free acid concentrations in the range of 0,03 to 0,1 N and plutonium concentrations between 1 to 5 g/l. (authors) [fr

Separation of glycols from dilute aqueous solutions via complexation with boronic acids

Energy Technology Data Exchange (ETDEWEB)

Randel, L.A.; King, C.J.

1991-07-01

This work examines methods of separating low molecular weight glycols from dilute aqueous solution. Extraction into conventional solvents is generally not economical, since, in the literature reviewed, distribution ratios for the two- to four-carbon glycols are all less than one. Distribution ratios can be increased, however, by incorporating into the organic phase an extracting agent that will complex with the solute of interest. The extracting agent investigated in this work is 3-nitrophenylboronic acid (NPBA). NPBA, a boric acid derivative, reversibly complexes with many glycols. The literature on complexation of borate and related compounds with glycols, including mechanistic data, measurement techniques, and applications to separation processes, provides information valuable for designing experiments with NPBA and is reviewed herein. 88 refs., 15 figs., 24 tabs.

Acid-Base Properties of Azo Dyes in Solution Studied Using Spectrophotometry and Colorimetry

Science.gov (United States)

Snigur, D. V.; Chebotarev, A. N.; Bevziuk, K. V.

2018-03-01

Colorimetry and spectrophotometry with chemometric data processing were used to study the acid-base properties of azo dyes in aqueous solution. The capabilities of both methods were compared. Ionization constants of all the functional groups of the azo compounds studied could be determined relative to the change in the specific color difference depending on the acidity of the medium. The colorimetric functions of ion-molecular forms of azo compounds used as an analytical signal allow us to obtain complete information on the acid-base equilibrium in a wide acidity range.

Adsorption of NI (II on activated Carbon of Coconut shell Chemicaly Modifieded with Acid Nitric Solutions

Directory of Open Access Journals (Sweden)

Mónica Hernández-Rodríguez

2017-01-01

Full Text Available In the research the effect of modification of coconut shell activated carbon with diluted solutions of nitric acid, in its chemical characteristics and removal capacity of the nickel (II ions present in modeling solutions of sulfates with similar characteristics to the acid liquor waste of the nickel industry, was studied. The characterization of the adsorbent material evidenced that the modification process increases the superficial acids groups according with the increase of acid nitric concentration employee in the treatment. The adsorption equilibrium tests, carried out with metallic species solutions at concentrations between 0,5 and 3,5 g/L evidenced that the process is described by Freundlich model. The effect of chemical modification of the adsorbent material in adsorption capacity of nickel (II ions was evaluated using a traditional experimental design at pH of 1,2 and 6,9 units, obtaining that the increase of acid groups in the carbon surface causes an increase of adsorption capacity and removal percentages of nickel (II, due to specific interactions of these groups with the metal cations.

Effects of infusion of branched chain amino-acids enriched TPN solutions on plasma amino-acid profiles in sepsis and trauma patients

NARCIS (Netherlands)

Vente, J. P.; von Meyenfeldt, M. F.; van Eijk, H. M.; van Berlo, C. L.; Gouma, D. J.; van der Linden, C. J.; Soeters, P. B.

1990-01-01

Total parenteral nutrition with branched chain amino-acids enriched solutions has been advocated in patients with sepsis and stress because of favourable effects on nitrogen balance, protein synthesis and immune competence. The rationale for the use of BCAA-enriched solutions is based on their

Stability of antibiotics and amino acids in two synthetic L-amino acid solutions commonly used for total parenteral nutrition in children

DEFF Research Database (Denmark)

Colding, H; Andersen, G E

1978-01-01

The stability and interaction at 29 degrees C of ampicillin, carbenicillin, gentamicin, and polymyxin B were examined in a common electrolyte solution, invertose darrow, and in two synthetic l-amino acid solutions, one commercial (vamin with fructose; Vitrum) and the other a neonatal preparation ...

Precipitation of plutonium from acidic solutions using magnesium oxide

International Nuclear Information System (INIS)

Jones, S.A.

1994-01-01

Plutonium (IV) is only marginally soluble in alkaline solution. Precipitation of plutonium using sodium or potassium hydroxide to neutralize acidic solutions produces a gelatinous solid that is difficult to filter and an endpoint that is difficult to control. If the pH of the solution is too high, additional species precipitate producing an increased volume of solids separated. The use of magnesium oxide as a reagent has advantages. It is added as a solid (volume of liquid waste produced is minimized), the pH is self-limiting (pH does not exceed about 8.5), and the solids precipitated are more granular (larger particle size) than those produced using KOH or NaOH. Following precipitation, the raffinate is expected to meet criteria for disposal to tank farms. The solid will be heated in a furnace to dry it and convert any hydroxide salts to the oxide form. The material will be cooled in a desiccator. The material is expected to meet vault storage criteria

Solubility Limits of Dibutyl Phosphoric Acid in Uranium Solutions at SRS

International Nuclear Information System (INIS)

Thompson, M.C.; Pierce, R.A.; Ray, R.J.

1998-06-01

The Savannah River Site has enriched uranium (EU) solution which has been stored for almost 10 years since being purified in the second uranium cycle of the H area solvent extraction process. The concentrations in solution are 6 g/L U and about 0.1 M nitric acid. Residual tributylphosphate in the solutions has slowly hydrolyzed to form dibutyl phosphoric acid (HDBP) at concentrations averaging 50 mg/L. Uranium is known to form compounds with DBP which have limited solubility. The potential to form uranium-DBP solids raises a nuclear criticality safety issue. SRTC tests have shown that U-DBP solids will precipitate at concentrations potentially attainable during storage of enriched uranium solutions. Evaporation of the existing EUS solution without additional acidification could result in the precipitation of U-DBP solids if DBP concentration in the resulting solution exceeds 110 ppm at ambient temperature. The same potential exists for evaporation of unwashed 1CU solutions. The most important variables of interest for present plant operations are HNO 3 and DBP concentrations. Temperature is also an important variable controlling precipitation. The data obtained in these tests can be used to set operating and safety limits for the plant. It is recommended that the data for 0 degrees C with 0.5 M HNO 3 be used for setting the limits. The limit would be 80 mg/L which is 3 standard deviations below the average of 86 observed in the tests. The data shows that super-saturation can occur when the DBP concentration is as much as 50 percent above the solubility limit. However, super-saturation cannot be relied on for maintaining nuclear criticality safety. The analytical method for determining DBP concentration in U solutions was improved so that analyses for a solution are accurate to within 10 percent. However, the overall uncertainty of results for periodic samples of the existing EUS solutions was only reduced slightly. Thus, sampling appears to be the largest portion

Volumetric properties of aqueous solutions of glutaric acid

International Nuclear Information System (INIS)

Ben-Hamo, Meyrav; Apelblat, Alexander; Manzurola, Emanuel

2007-01-01

Densities of aqueous solutions with molalities up to 6 mol . kg -1 were determined at 5 K temperature intervals, from T = 288.15 K to T = 333.15 K. Densities served to evaluate the apparent molar volumes, V 2,φ (m, T), the cubic expansion coefficients, α(m, T), and the changes of isobaric heat capacities with respect to pressure, (∂C P /∂P) T,m . They were qualitatively correlated with the changes in the structure of water when glutaric acid is dissolved in it

Effect of Surface Precipitate on the Crevice Corrosion in HYBRID and Oxalic Acid Solution

International Nuclear Information System (INIS)

Park, S. Y.; Jung, J. Y.; Won, H. J.; Kim, S. B.; Choi, W. K.; Moon, J. K.; Park, S. J.

2015-01-01

In this study, we investigated the characteristics of the crevice corrosion for Inconel-600 and 304SS in OA solution according to the change in pH. The evaluation of the crevice corrosion with the chemical thermodynamic analysis identified the effect of the residual chemicals such as iron-oxalate and nickeloxalate to the crevice corrosion behavior. Test results were compared with those of HYBRID (HYdrizine Base Reductive metal Ion Decontamination). The crevice corrosion properties of 304 SS and Inconel-600 in HYBRID and oxalic acid solution were evaluated. In case of oxalic acid solution, the corrosion rate on 304SS was rapidly increased with a pH decrease of around 2, but there was no increase in the corrosion rate on Inconel-600

Adsorptive removal of acid blue 113 and tartrazine by fly ash from single and binary dye solutions

Energy Technology Data Exchange (ETDEWEB)

Pura, S.; Atun, G. [Istanbul University, Avcilar (Turkey). Dept. of Chemistry

2009-07-01

Adsorption of two acid dyestuffs, acid blue 113 (AB) and tartrazine (TA), has been studied from their single and binary solutions by using fly ash (FA) as an adsorbent. The S shaped isotherms observed for dye adsorption from single solutions show that both acid dyes are not preferred at a low concentration region whereas adsorption of the dyes from binary solutions is enhanced via solute-solute interactions. Although the L-shaped isotherm is observed in binary solutions adsorbability of AB decreases in concentrated solutions with respect to single one, time dependency of adsorption is well described with a pseudo-second-order kinetic model as well as the linear relation of Bt vs. t plots (not passing through origin) indicates that film diffusion is effective on dye adsorption. Modeled isotherm curves using isotherm parameters of the Freundlich and Dubinin-Radushkevich (D-R) equations adequately fit to experimental equilibrium data. Equilibrium adsorption of AB in binary solutions has been quite well predicted by the extended Freundlich and the Sheindorf-Rebuhn-Sheintuch (SRS) models. In general, the isotherm curves constructed in the temperature range of 298-328K show that the optimum temperature is 318K for AB removal from both single and binary solutions.

[Analyze nanofiltration separation rule of chlorogenic acid from low concentration ethanol by Donnan effect and solution-diffusion effect].

Science.gov (United States)

Li, Cun-Yu; Liu, Li-Cheng; Jin, Li-Yang; Li, Hong-Yang; Peng, Guo-Ping

2017-07-01

To separate chlorogenic acid from low concentration ethanol and explore the influence of Donnan effect and solution-diffusion effect on the nanofiltration separation rule. The experiment showed that solution pH and ethanol volume percent had influences on the separation of chlorogenic acid. Within the pH values from 3 to 7 for chlorogenic acid in 30% ethanol, the rejection rate of chlorogenic acid was changed by 70.27%. Through the response surface method for quadratic regression model, an interaction had been found in molecule weight cut-off, pH and ethanol volume percent. In fixed nanofiltration apparatus, the existence states of chlorogenic acid determinedits separation rules. With the increase of ethanol concentration, the free form chlorogenic acid was easily adsorbed, dissolved on membrane surface and then caused high transmittance due to the solution-diffusion effect. However, at the same time, due to the double effects of Donnan effect and solution-diffusion effect, the ionic state of chlorogenic acid was hard to be adsorbed in membrane surface and thus caused high rejection rate. The combination of Box-Behnken design and response surface analysis can well optimize the concentrate process by nanofiltration, and the results showed that nanofiltration had several big advantages over the traditional vacuum concentrate technology, meanwhile, and solved the problems of low efficiency and serious component lossesin the Chinese medicines separation process for low concentration organic solvent-water solution. Copyright© by the Chinese Pharmaceutical Association.

Elimination par électrodialyse des ions Fe(II) d'une solution d'acide ...

African Journals Online (AJOL)

Administrateur

concentration de l'acide (H2SO4) et la température sur l'efficacité d'élimination de Fe(II) a été étudiée. Les .... C. Negro et al. [20] ont étudié la possibilité de récupérer l'acide sulfurique à partir de solution d'acide sulfurique contenant du sulfate de cuivre. L. Cifuentes et al. ..... removal from rinsing water after metal etching,.

A pulse radiolysis study of salicylic acid and 5-sulpho-salicylic acid in aqueous solutions

International Nuclear Information System (INIS)

Kishore, Kamal; Mukherjee, T.

2006-01-01

Reactions of H, OH, e aq - and some one-electron oxidants have been studied with salicylic acid and 5-sulpho-salicylic acid in aqueous solutions. Rate constants for the reaction of e aq - with these compounds were of the order of 10 9 dm 3 mol -1 s -1 and this reaction led to the formation of reducing radicals which could transfer electron to methyl viologen. Other one-electron reductants were not able to reduce these compounds. OH radicals reacted with these compounds by addition pathway with very high rate constants (>10 10 dm 3 mol -1 s -1 ) while O - radical anions could oxidize these molecules to give phenoxyl type of radicals. Amongst the one-electron oxidants, only N 3 radicals and SO 4 - radicals could oxidize salicylic acid while 5-sulpho-salicylic acid could be oxidized only by SO 4 - radicals indicating that while one-electron reduction potential for semi-oxidized SA may be o1 for N 3 ? radical), it is more than 1.33V vs. NHE for semi-oxidized SSA species

Collagen tissue treated with chitosan solutions in carbonic acid for improved biological prosthetic heart valves

Energy Technology Data Exchange (ETDEWEB)

Gallyamov, Marat O., E-mail: glm@spm.phys.msu.ru [Faculty of Physics, Lomonosov Moscow State University, Leninskie gory 1–2, Moscow 119991 (Russian Federation); Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Vavilova 28, Moscow 119991 (Russian Federation); Chaschin, Ivan S. [Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Vavilova 28, Moscow 119991 (Russian Federation); Khokhlova, Marina A. [Faculty of Physics, Lomonosov Moscow State University, Leninskie gory 1–2, Moscow 119991 (Russian Federation); Grigorev, Timofey E. [Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Vavilova 28, Moscow 119991 (Russian Federation); Bakuleva, Natalia P.; Lyutova, Irina G.; Kondratenko, Janna E. [Bakulev Scientific Center for Cardiovascular Surgery of the Russian Academy of Medical Sciences, Roublyevskoe Sh. 135, Moscow 121552 (Russian Federation); Badun, Gennadii A.; Chernysheva, Maria G. [Radiochemistry Division, Faculty of Chemistry, Lomonosov Moscow State University, Leninskie gory 1–2, Moscow 119991 (Russian Federation); Khokhlov, Alexei R. [Faculty of Physics, Lomonosov Moscow State University, Leninskie gory 1–2, Moscow 119991 (Russian Federation); Nesmeyanov Institute of Organoelement Compounds, Russian Academy of Sciences, Vavilova 28, Moscow 119991 (Russian Federation)

2014-04-01

Calcification of bovine pericardium dramatically shortens typical lifetimes of biological prosthetic heart valves and thus precludes their choice for younger patients. The aim of the present work is to demonstrate that the calcification is to be mitigated by means of treatment of bovine pericardium in solutions of chitosan in carbonic acid, i.e. water saturated with carbon dioxide at high pressure. This acidic aqueous fluid unusually combines antimicrobial properties with absolute biocompatibility as far as at normal pressure it decomposes spontaneously and completely into H{sub 2}O and CO{sub 2}. Yet, at high pressures it can protonate and dissolve chitosan materials with different degrees of acetylation (in the range of 16–33%, at least) without any further pretreatment. Even exposure of the bovine pericardium in pure carbonic acid solution without chitosan already favours certain reduction in calcification, somewhat improved mechanical properties, complete biocompatibility and evident antimicrobial activity of the treated collagen tissue. The reason may be due to high extraction ability of this peculiar compressed fluidic mixture. Moreover, exposure of the bovine pericardium in solutions of chitosan in carbonic acid introduces even better mechanical properties and highly pronounced antimicrobial activity of the modified collagen tissue against adherence and biofilm formation of relevant Gram-positive and Gram-negative strains. Yet, the most important achievement is the detected dramatic reduction in calcification for such modified collagen tissues in spite of the fact that the amount of the thus introduced chitosan is rather small (typically ca. 1 wt.%), which has been reliably detected using original tritium labelling method. We believe that these improved properties are achieved due to particularly deep and uniform impregnation of the collagen matrix with chitosan from its pressurised solutions in carbonic acid. - Highlights: • Treatment of GA

Collagen tissue treated with chitosan solutions in carbonic acid for improved biological prosthetic heart valves

International Nuclear Information System (INIS)

Gallyamov, Marat O.; Chaschin, Ivan S.; Khokhlova, Marina A.; Grigorev, Timofey E.; Bakuleva, Natalia P.; Lyutova, Irina G.; Kondratenko, Janna E.; Badun, Gennadii A.; Chernysheva, Maria G.; Khokhlov, Alexei R.

2014-01-01

Calcification of bovine pericardium dramatically shortens typical lifetimes of biological prosthetic heart valves and thus precludes their choice for younger patients. The aim of the present work is to demonstrate that the calcification is to be mitigated by means of treatment of bovine pericardium in solutions of chitosan in carbonic acid, i.e. water saturated with carbon dioxide at high pressure. This acidic aqueous fluid unusually combines antimicrobial properties with absolute biocompatibility as far as at normal pressure it decomposes spontaneously and completely into H 2 O and CO 2 . Yet, at high pressures it can protonate and dissolve chitosan materials with different degrees of acetylation (in the range of 16–33%, at least) without any further pretreatment. Even exposure of the bovine pericardium in pure carbonic acid solution without chitosan already favours certain reduction in calcification, somewhat improved mechanical properties, complete biocompatibility and evident antimicrobial activity of the treated collagen tissue. The reason may be due to high extraction ability of this peculiar compressed fluidic mixture. Moreover, exposure of the bovine pericardium in solutions of chitosan in carbonic acid introduces even better mechanical properties and highly pronounced antimicrobial activity of the modified collagen tissue against adherence and biofilm formation of relevant Gram-positive and Gram-negative strains. Yet, the most important achievement is the detected dramatic reduction in calcification for such modified collagen tissues in spite of the fact that the amount of the thus introduced chitosan is rather small (typically ca. 1 wt.%), which has been reliably detected using original tritium labelling method. We believe that these improved properties are achieved due to particularly deep and uniform impregnation of the collagen matrix with chitosan from its pressurised solutions in carbonic acid. - Highlights: • Treatment of GA-stabilised bovine

Thermophysical property characterization of aqueous amino acid salt solution containing serine

International Nuclear Information System (INIS)

Navarro, Shanille S.; Leron, Rhoda B.; Soriano, Allan N.; Li, Meng-Hui

2014-01-01

Highlights: • Thermophysical properties of aqueous potassium and sodium salt solutions of serine were studied. • Density, viscosity, refractive index and electrolytic conductivity of the solution were measured. • The concentrations of amino acid salt ranges from x 1 = 0.009 to 0.07. • The temperature range studied was (298.15 to 343.15) K. • The measured data were represented satisfactorily by using the applied correlations. - Abstract: Thermophysical property characterization of aqueous potassium and sodium salt solutions containing serine was conducted in this study; specifically the system’s density, refractive index, electrical conductivity, and viscosity. Measurements were obtained over a temperature range of (298.15 to 343.15) K and at normal atmospheric pressure. Composition range from x 1 = 0.009 to 0.07 for aqueous potassium and sodium salt solutions containing serine was used. The sensitivity of the system’s thermophysical properties on temperature and composition variation were discussed and correlated based on the equations proposed for room temperature ionic liquids. The density, viscosity, and refractive index measurements of the aqueous systems were found to decrease as the temperature increases at fixed concentration and the values increase as the salt concentration increases (water composition decreases) at fixed temperature. Whereas, a different trend was observed for the electrical conductivity data; at fixed concentration, the conductivity values increase as the temperature increases and at fixed temperature, its value generally increases as the salt concentration increases but only to a certain level (specific concentration) wherein the conductivity of the solution starts to decrease when the concentration of the salt is further increased. Calculation results show that the applied models were satisfactory in representing the measured properties in the aqueous amino acid salt solution containing serine

Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

Energy Technology Data Exchange (ETDEWEB)

Brown, L. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada); Bonin, H.W. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada)]. E-mail: bonin-h@rmc.ca; Bui, V.T. [Department of Chemistry and Chemical Engineering, Royal Military College of Canada, Kingston, Ont., K7K 7B4 (Canada)

2005-05-15

The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment.

Mixed field radiation effects on dry and acidic solution saturated polyamide 6,6

International Nuclear Information System (INIS)

Brown, L.; Bonin, H.W.; Bui, V.T.

2005-01-01

The disposal of Canada's radioactive waste materials has been the focus of ongoing research at the Royal Military College of Canada, in the use of polymer-based composite materials for the fabrication of disposal containers. An evaluation of the performance of polyamide 6,6 after exposure to radiation and acidic aqueous solutions provides the basis for the assessment of the lifetime performance of a polymeric-based storage container. This work demonstrates the importance of the combined effects of aqueous solution diffusion and radiation exposure on the mechanical performance and molecular structure of polyamide 6,6. Irradiation of dry samples initially results in a marked reduction of mechanical performance, however, post-irradiation aging allows for the return to pre-irradiation mechanical strength. Samples irradiated after exposure to either distilled water or 0.1 M sulfuric acid solutions exhibited increases in mechanical performance upon exposure to a mixed field radioactive environment

Adsorption of Copper Ion using Acrylic Acid-g-Polyaniline in Aqueous Solution

Science.gov (United States)

Kamarudin, Sabariah; Mohammad, Masita

2018-04-01

A conductive polymer, polyaniline (PANI) has unique electrical behaviour, stable in the environment, easy synthesis and have wide application in various fields. Modification of PANI in order to improve its adsorption capacity has been done. In this study, the polyaniline-grafted acrylic acid has been prepared and followed by adsorption of copper ion in aqueous solution. Acrylic acid, PANI and acrylic acid-g-polyaniline (Aag-PANI) were characterized by FTIR and SEM to determine its characteristic. The adsorption capacity was investigated to study the removal capacity of Cu ion from aqueous solution. Two parameters were selected which are pH (2, 4 and 6) and initial metal ion concentration (50 mg/L, 100 mg/L and 200 mg/L). The maximum adsorption capacity for PANI and Aag-PANI are 1.7 mg/g and 64.6 mg/g, respectively, at an initial concentration of 100 mg/L. The Langmuir adsorption isotherm model and Freundlich adsorption isotherm model have been used and showed that it is heterolayer adsorption by follows the Freundlich isotherm model.

Simultaneous determination of nitric acid and uranium concentrations in aqueous solution from measurements of electrical conductivity, density, and temperature

International Nuclear Information System (INIS)

Spencer, B.B.

1991-01-01

Nuclear fuel reprocessing plants handle aqueous solutions of nitric acid and uranium in large quantities. Automatic control of process operations requires reliable measurements of these solutes concentration, but this is difficult to directly measure. Physical properties such as solution density and electrical conductivity vary with solute concentration and temperature. Conductivity, density and temperature can be measured accurately with relatively simple and inexpensive devices. These properties can be used to determine solute concentrations will good correlations. This paper provides the appropriate correlations for solutions containing 2 to 6 Molar (M) nitric acid and 0 to 300 g/L uranium metal at temperatures from 25--90 degrees C. The equations are most accurate below 5 M nitric acid, due to a broad maximum in the conductivity curve at 6 M. 12 refs., 9 figs., 6 tabs

Precipitation stripping of neodymium from carboxylate extractant with aqueous oxalic acid solutions

International Nuclear Information System (INIS)

Konishi, Yasuhiro; Asai, Satoru; Murai, Tetuya

1993-01-01

This paper describes a precipitation stripping method in which neodymium ions are stripped from carboxylate extractant in organic solvent and simultaneously precipitated with aqueous oxalic acid solution. For the single-stage process, a quantitative criterion for precipitating oxalate powders was derived theoretically, and stripping experiments were done under the precipitation conditions. The resultant precipitates were neodymium oxalate, which is completely free from contamination by the carboxylate extractant and the organic solvent. The overall rate of stripping was controlled by the transfer of neodymium carboxylate in the organic solution, indicating that the presence of oxalic acid in the aqueous phase has no effect on the stripping rate. These findings demonstrate the feasibility of combining the conventional stripping and precipitation stages in a solvent extraction process for separation and purification of rare earths

Behavior of Am in acidic and basic solutions of potassium ferri/ferrocyanide

International Nuclear Information System (INIS)

Kulyako, Yu.M.; Trofimov, T.I.; Malikov, D.A.; Lebedev, I.A.; Myasoedov, B.F.

1994-01-01

The behavior of Am in acidic and basic solutions containing the Fe(CN) 3- 6 /Fe(CN) 4- 6 redox system is studied. In mineral acids, K 3 Fe(CN) 6 and Am(III) form the poorly soluble compound AmFe(CN) 6 , which with time undergoes a change owing to radiolytic reduction of Fe(CN) 3- 6 to Fe(CN) 4- 6 . In basic solutions of K 3 Fe(CN) 6 , Am(III) is oxidized to AmO + 2 , forming the soluble complex (AmO 2 ) 3 Fe(CN) 6 , which gradually decomposes to produce the solid double hydroxide Na 2 AmO 2 (OH) 3 ·nH 2 O. An Am(IV) hydroxide is formed if [Am] and [K 3 Fe(CN) 6 ] are equal

Adsorption of uranium ions by crosslinked polyester resin functionalized with acrylic acid from aqueous solutions

International Nuclear Information System (INIS)

Cemal Oezeroglu; Niluefer Metin

2012-01-01

In this paper, the crosslinked polyester resin containing acrylic acid functional groups was used for the adsorption of uranium ions from aqueous solutions. For this purpose, the crosslinked polyester resin of unsaturated polyester in styrene monomer (Polipol 353, Poliya) and acrylic acid as weight percentage at 80 and 20%, respectively was synthesized by using methyl ethyl ketone peroxide (MEKp, Butanox M60, Azo Nobel)-cobalt octoate initiator system. The adsorption of uranium ions on the sample (0.05 g copolymer and 5 mL of U(VI) solution were mixed) of the crosslinked polyester resin functionalized with acrylic acid was carried out in a batch reactor. The effects of adsorption parameters of the contact time, temperature, pH of solution and initial uranium(VI) concentration for U(VI) adsorption on the crosslinked polyester resin functionalized with acrylic acid were investigated. The adsorption data obtained from experimental results depending on the initial U(VI) concentration were analyzed by the Freundlich, Langmuir and Dubinin-Radushkevich (D-R) adsorption isotherms. The adsorption capacity and free energy change were determined by using D-R isotherm. The obtained experimental adsorption data depending on temperature were evaluated to calculate the thermodynamic parameters of enthalpy (ΔH o ), entropy (ΔS o ) and free energy change (ΔG o ) for the U(VI) adsorption on the crosslinked polyester resin functionalized with acrylic acid from aqueous solutions. The obtained adsorption data depending on contact time were analyzed by using adsorption models such as the modified Freundlich, Elovich, pseudo-first order and pseudo-second-order kinetic models. (author)

Volumetric properties of aqueous solutions of glutaric acid

Energy Technology Data Exchange (ETDEWEB)

Ben-Hamo, Meyrav [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel); Apelblat, Alexander [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)]. E-mail: apelblat@bgu.ac.il; Manzurola, Emanuel [Department of Chemical Engineering, Ben Gurion University of the Negev, P.O. Box 653, Beer Sheva 84105 (Israel)

2007-07-15

Densities of aqueous solutions with molalities up to 6 mol . kg{sup -1} were determined at 5 K temperature intervals, from T = 288.15 K to T = 333.15 K. Densities served to evaluate the apparent molar volumes, V {sub 2,{phi}}(m, T), the cubic expansion coefficients, {alpha}(m, T), and the changes of isobaric heat capacities with respect to pressure, ({partial_derivative}C {sub P}/{partial_derivative}P) {sub T,m}. They were qualitatively correlated with the changes in the structure of water when glutaric acid is dissolved in it.

Study of ion exchange behaviour of some elements at phosphonic-acid cationite in diluted solutions of nitric acid

International Nuclear Information System (INIS)

Razbash, A.A.; Sevast'yanov, Yu.G.

1985-01-01

Ce(3, 4), Eu(3), Gd(3), Sm(3), Sc(3) distribution coefficients are determined in the macroporic phosphonic acid cationite KRF-20T-60 in nitric acid solutions in 0.1-2.0 M concentration interval using statistical method. A simple method of cerium-139 radionuclide extraction from the industrial lanthanum target is developed. The product yield made up more than 99%, specific activity - 2.37x10 9 Bq/mg, radiochemical purity - no less than 99.9%

Electrochemical Studies of Lead Telluride Behavior in Acidic Nitrate Solutions

Directory of Open Access Journals (Sweden)

Rudnik E.

2015-04-01

Full Text Available Electrochemistry of lead telluride stationary electrode was studied in nitric acid solutions of pH 1.5-3.0. E-pH diagram for Pb-Te-H2O system was calculated. Results of cyclic voltammetry of Pb, Te and PbTe were discussed in correlation with thermodynamic predictions. Anodic dissolution of PbTe electrode at potential approx. -100÷50 mV (SCE resulted in tellurium formation, while above 300 mV TeO2 was mainly produced. The latter could dissolve to HTeO+2 under acidic electrolyte, but it was inhibited by increased pH of the bath.

EXTRACTION AND SORPTION BENZOIC ACID FROM AQUEOUS SOLUTIONS OF POLYMERS BASED ON N-VINYLAMIDES

Directory of Open Access Journals (Sweden)

A. G. Savvina

2015-01-01

Full Text Available The widespread use of aromatic acids (benzoic acid, salicylic as preservatives necessitates their qualitative and quantitative determination in food. Effective and common way to separation and concentration of aromatic acids liquid extraction. Biphasic system of water-soluble polymers based on (poly-N-vinyl pyrrolidone, and poly-N-vinylcaprolactam satisfy the requirements of the extraction system. When sorption concentration improved definition of the metrological characteristics, comply with the requirements for sensitivity and selectivity definition appears possible, use of inexpensive and readily available analytical equipment. When studying the adsorption of benzoic acid used as a sorbent crosslinked polymer based on N-vinyl pyrrolidone, obtained by radical polymerisation of a functional monomer and crosslinker. In the extraction of benzoic acid to maximize the allocation of water and the organic phase of the polymer used salt solutions with concentrations close to saturation. Regardless of the nature of the anion salt is used as salting-out agent, aromatic acids sorption increases with the size of the cations. In the experiment the maximum recovery rate (80% benzoic acid obtained in the PVP (0.2 weight%. Ammonium sulphate. The dependence stepepni benzoic acid extraction from time sorption sorbent mass and the pH of the aqueous phase. To establish equilibrium in the system, for 20 minutes. The dependence of the degree of extraction of the acid pH indicates that the acid is extracted into the molecular form. The maximum adsorption is reached at pH 3,5, with its efficiency decreases symbatically reduce the amount of undissociated acid molecules in solution.

Shock wave synthesis of amino acids from solutions of ammonium formate and ammonium bicarbonate

Science.gov (United States)

Suzuki, Chizuka; Furukawa, Yoshihiro; Kobayashi, Takamichi; Sekine, Toshimori; Nakazawa, Hiromoto; Kakegawa, Takeshi

2015-07-01

The emergence of life's building blocks, such as amino acids and nucleobases, on the prebiotic Earth was a critical step for the beginning of life. Reduced species with low mass, such as ammonia, amines, or carboxylic acids, are potential precursors for these building blocks of life. These precursors may have been provided to the prebiotic ocean by carbonaceous chondrites and chemical reactions related to meteorite impacts on the early Earth. The impact of extraterrestrial objects on Earth occurred more frequently during this period than at present. Such impacts generated shock waves in the ocean, which have the potential to progress chemical reactions to form the building blocks of life from reduced species. To simulate shock-induced reactions in the prebiotic ocean, we conducted shock-recovery experiments on ammonium bicarbonate solution and ammonium formate solution at impact velocities ranging from 0.51 to 0.92 km/s. In the products from the ammonium formate solution, several amino acids (glycine, alanine, ß-alanine, and sarcosine) and aliphatic amines (methylamine, ethylamine, propylamine, and butylamine) were detected, although yields were less than 0.1 mol % of the formic acid reactant. From the ammonium bicarbonate solution, smaller amounts of glycine, methylamine, ethylamine, and propylamine were formed. The impact velocities used in this study represent minimum cases because natural meteorite impacts typically have higher velocities and longer durations. Our results therefore suggest that shock waves could have been involved in forming life's building blocks in the ocean of prebiotic Earth, and potentially in aquifers of other planets, satellites, and asteroids.

Dissolution of thorium/uranium mixed oxide in nitric acid-hydrofluoric acid solution

International Nuclear Information System (INIS)

Filgueiras, S.A.C.

1984-01-01

The dissolution process of thorium oxide and mixed uranium-thorium oxide is studied, as a step of the head-end of the fuel reprocessing. An extensive bibliography was analysed, concerning the main aspects of the system, specially the most important process variables. Proposed mechanisms and models for the thorium oxide dissolution are presented. The laboratory tests were performed in two phases: at first, powdered thoria was used as the material to be dissolved. The objective was to know how changes in he concentrations of the dissolvent solution components HNO 3 , HF and Al(NO 3 ) 3 affect the dissolution rate. The tests were planned according to the fractional factorial method. Thes results showed that it is advantageous to work with powdered material, since the reaction occurs rapidly. And, if the Thorex solution (HNO 3 13M, HF 0.05M and Al(NO 3 ) 3 0.10M) is a suitable dissolvent, it was verified that it is possible to reduce the concentration of either nitric or fluoridric acid, without reducing the reaction rate to an undesirable value. It was also observed significant interaction between the components of the dissolvent solution. In the second phase of the tests, (Th, 5%U)O 2 sintered pellets were used. The main goals were to know the pellets dissolution behaviour and to compare the results for different pellets among themselves. It was observed that the metallurgical history of the material strongly influences its dissolution, specially the density and the microstructure. It was also studied how the (Th,U)O 2 mass/Thorex solution volume ratio affects the time needed to obtain an 1 M Th/liter solution. The activation energy for the reaction was obtained. (Author) [pt

Electrospinning of chitosan solutions in acetic acid with poly(ethylene oxide).

Science.gov (United States)

Duan, Bin; Dong, Cunhai; Yuan, Xiaoyan; Yao, Kangde

2004-01-01

Electrospinning of chitosan solutions with poly(ethylene oxide) (PEO) in an aqueous solution of 2 wt% acetic acid was studied. The properties of the chitosan/PEO solutions, including conductivity, surface tension and viscosity, were measured. Morphology of the electrospun chitosan/PEO was observed by using scanning electron micrographs. Results showed that the ultrafine fibers could be generated after addition of PEO in 2:1 or 1:1 mass ratios of chitosan to PEO from 4-6 wt% chitosan/PEO solutions at 15 kV voltage, 20 cm capillary-collector distance and flow rate 0.1 ml/h. During electrospinning of the chitosan/PEO solutions, ultrafine fibers with diameters from 80 nm to 180 nm were obtained, while microfibers with visually thicker diameters could be formed as well. Results of X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy and differential scanning calorimeter exhibited the larger electrospun microfibers were almost entirely made from PEO, while the electrospun ultrafine fibers mainly contained chitosan.

Surface characterisation of ethylene-propylene-diene rubber upon exposure to aqueous acidic solution

DEFF Research Database (Denmark)

Mitra, S.; Ghanbari-Siahkali, Afshin; Kingshott, P.

2006-01-01

but significantly different with respect to molar mass and the presence of long chain branching. Both rubbers contained 5-ethylidene-2-norbomene (ENB) as diene. Solution cast films of pure EPDM samples were exposed in two different acidic solutions, viz. chromosulphuric (Cr (VI)/H2SO4) and sulphuric acid (H2SO4....... Furthermore, 20% Cr (VI)/H2SO4 also attacked the allylic carbon-hydrogen (C-H) bonds of ENB resulting in more oxygenated species on the surface compared to 20% H2SO4 under identical conditions. Cr (VI) in the 20% Cr (VI)/H2SO4 was found to play an important role in alteration of surface chemistry. Studies...

Copper-Sulfate Pentahydrate as a Product of the Waste Sulfuric Acid Solution Treatment

OpenAIRE

Marković, Radmila; Stevanović, Jasmina; Avramović, Ljiljana; Nedeljković, Dragutin; Jugović, Branimir; Stajić Trošić, Jasna; Gvozdenović, Milica M.

2012-01-01

The aim of this study is synthesis of copper-sulfate pentahydrate from the waste sulfuric acid solution-mother liquor generated during the regeneration process of copper bleed solution. Copper is removed from the mother liquor solution in the process of the electrolytic treatment using the insoluble lead anodes alloyed with 6 mass pct of antimony on the industrial-scale equipment. As the result of the decopperization process, copper is removed in the form of the cathode sludge and is precipit...

Copper-Sulfate Pentahydrate as a Product of the Waste Sulfuric Acid Solution Treatment

Science.gov (United States)

Marković, Radmila; Stevanović, Jasmina; Avramović, Ljiljana; Nedeljković, Dragutin; Jugović, Branimir; Stajić-Trošić, Jasna; Gvozdenović, Milica

2012-12-01

The aim of this study is synthesis of copper-sulfate pentahydrate from the waste sulfuric acid solution-mother liquor generated during the regeneration process of copper bleed solution. Copper is removed from the mother liquor solution in the process of the electrolytic treatment using the insoluble lead anodes alloyed with 6 mass pct of antimony on the industrial-scale equipment. As the result of the decopperization process, copper is removed in the form of the cathode sludge and is precipitated at the bottom of the electrolytic cell. By this procedure, the content of copper could be reduced to the 20 mass pct of the initial value. Chemical characterization of the sludge has shown that it contains about 90 mass pct of copper. During the decopperization process, the very strong poison, arsine, can be formed, and the process is in that case terminated. The copper leaching degree of 82 mass pct is obtained using H2SO4 aqueous solution with the oxygen addition during the cathode sludge chemical treatment at 80 °C ± 5 °C. Obtained copper salt satisfies the requirements of the Serbian Standard for Pesticide, SRPS H.P1. 058. Therefore, the treatment of waste sulfuric acid solutions is of great economic and environmental interest.

Selective oxidation of glycerol to formic acid in highly concentrated aqueous solutions with molecular oxygen using V-substituted phosphomolybdic acids

KAUST Repository

Zhang, Jizhe

2014-01-01

Formic acid is an important commodity chemical as well as a promising medium for hydrogen storage and hydrogen production. In this paper, we report that formic acid can be produced through selective oxidation of glycerol, a low-cost by-product of biodiesel, by using vanadium-substituted phosphomolybdic acids as catalysts and molecular oxygen as the oxidant. Significantly, this catalytic system allows for high-concentration conversions and thus leads to exceptional efficiency. Specifically, 3.64 g of formic acid was produced from 10 g of glycerol/water (50/50 in weight) solution. © 2014 the Partner Organisations.

Mechanism and Kinetics for the Dissolution of Apatitic Materials in Acid Solutions

Directory of Open Access Journals (Sweden)

Calmanovici C.E.

1997-01-01

Full Text Available Abstract - This work concerns the study of the digestion step in the production process of phosphoric acid. Some qualitative experiments indicate that the difference between the pH at the surface of the phosphate and that in the bulk of the solution is negligible and that the dissolution is controlled by diffusion of products away from the phosphate particle. In further experiments, to isolate the dissolution phenomenon from the formation of calcium sulfate, the sulfuric acid normally used industrially is replaced by hydrochloric acid. The phosphate material used in our experiments is a model apatitic material: synthetic hydroxyapatite (HAP. The dissolution of calcium hydroxyapatite was studied with increasing amounts of calcium and phosphate at different temperatures. A simple method was developed for this observation based on the time required for complete dissolution of the HAP powder. The results confirm that the dissolution is controlled by a diffusional process through an interface of calcium and phosphate ions released from the solid surface. A kinetic model for the dissolution of apatitic materials is proposed which assumes a shrinking particle behaviour controlled by diffusion of calcium ions. The experimental results are fitted to this model to determine the mass transfer constant for HAP dissolution in acid solutions. The activation energy of the reaction is about 14kJ/mol. This study was carried on in conditions similar to the industrial ones for the production of phosphoric acid by the dihydrate-process

Evaluation of Acoustic Cavitation in Terephthalic Acid Solutions Containing Gold Nanoparticles by the Spectrofluorometry Method

Directory of Open Access Journals (Sweden)

Ameneh Sazgarnia

2012-01-01

Full Text Available Background. When a liquid is irradiated with high intensity and low-frequency ultrasound, acoustic cavitation occurs. The existence of particles in a liquid provides nucleation sites for cavitation bubbles and leads to a decrease in the ultrasonic intensity threshold needed for cavitation onset. Materials and Methods. The study was designed to measure hydroxyl radicals in terephthalic acid solutions containing gold nanoparticles in a near field of a 1 MHz sonotherapy probe. The effect of ultrasound irradiation parameters containing mode of sonication and ultrasound intensity in hydroxyl radicals production have been investigated by the spectrofluorometry method. Results. Recorded fluorescence signal in terephthalic acid solution containing gold nanoparticles was higher than the terephthalic acid solution without gold nanoparticles. Also, the results showed that any increase in intensity of the sonication would be associated with an increase in the fluorescence intensity. Conclusion. Acoustic cavitation in the presence of gold nanoparticles has been introduced as a way for improving therapeutic effects on the tumors in sonodynamic therapy. Also, the terephthalic acid dosimetry is suitable for detecting and quantifying free hydroxyl radicals as a criterion of cavitation production over a certain range of conditions in medical ultrasound fields.

Radiation-chemical behaviour of neptunium ions in nitric acid solutions in the presence of curium-244

International Nuclear Information System (INIS)

Frolova, L.M.; Frolov, A.A.; Vasil'ev, V.Ya.

1984-01-01

Radiation-chemical behaviour of neptunium ions in nitric acid solutions is studied under the action of intensive internal alpha-irradiation conditioned by curium nuclides. In 0.3-1.1 mol/l solutions of nitric acid radiation-chemical oxidation of neptunium (4) and reduction of neptunium (6) is obeyed to the first order law of reaction rate in respect to neptunium concentration. Effective constants of neptunium (4) oxidation rates and neptuniumi(6) reduction rates are not dependent on neptunium ion in1tial concentration and increase with a growth of a dose rate of alpha-irradiation of solution. In equilibrium only neptunium (5) and neptunium (6) are present in solutions with HNO 3 concentration less than 1 mol/l. In more concentrated solutions equilibrium between sexa-, penta- and tetravalent neptunium forms is established. Equilibrium concentrations of neptunium valent forms are not dependent on neptunium initial oxidation state under the same initial conditions (dose rate, neptunium concentration and acidity. It is shown form experimental data that under the action of alpha-irradiation neptunium (5) both is oxidated to neptunium (6) and is reduced to neptunium (4)

Volumetric studies of some amino acids in binary aqueous solutions ...

Indian Academy of Sciences (India)

Unknown

0 values of glycine, L-alanine, and L-valine in aqueous MgCl2⋅6H2O solutions at. 298⋅15 K in order to describe the temperature dependence behaviour of partial molar quantities. Group contributions to partial molar volumes have been determined for the amino acids. The trends of transfer volumes (∆Vφ. 0) have been ...

THIOGLYCOLIC ACID ESTERIFIED IN TO RICE STRAW FOR REMOVING LEAD FROM AQUEOUS SOLUTION

Directory of Open Access Journals (Sweden)

R. Gong

2011-09-01

Full Text Available Thiol rice straw (TRS was prepared by esterifying thioglycolic acid onto rice straw in the medium of acetic anhydride and acetic acid with sulfuric acid as catalyst. The sorption of lead (Pb on TRS from aqueous solution was subsequently investigated. The batch experiments showed that Pb removal was dependent on initial pH, sorbent dose, Pb concentration, contact time, and temperature. The maximum value of Pb removal appeared at pH 5. For 100 mg/L of Pb solution, a removal ratio of greater than 98% could be achieved with 2.0 g/L or more of TRS. The isothermal data of Pb sorption conformed well to the Langmuir model, and the maximum sorption capacity (Qm of TRS for Pb was 104.17 mg/g. The equilibrium of Pb removal was reached within 120 min. The Pb removal process could be described by the pseudo-first-order kinetic model. The thermodynamic study indicated that the Pb removal process was spontaneous and endothermic.

The response of soil solution chemistry in European forests to decreasing acid deposition

DEFF Research Database (Denmark)

Johnson, James; Pannatier, Elisabeth Graf; Carnicelli, Stefano

2018-01-01

to emissions controls. In this study, we assessed the response of soil solution chemistry in mineral horizons of European forests to these changes. Trends in pH, acid neutralizing capacity (ANC), major ions, total aluminium (Altot) and dissolved organic carbon were determined for the period 1995–2012. Plots...... with at least 10 years of observations from the ICP Forests monitoring network were used. Trends were assessed for the upper mineral soil (10–20 cm, 104 plots) and subsoil (40–80 cm, 162 plots). There was a large decrease in the concentration of sulphate () in soil solution; over a 10‐year period (2000...... over the entire dataset. The response of soil solution acidity was nonuniform. At 10–20 cm, ANC increased in acid‐sensitive soils (base saturation ≤10%) indicating a recovery, but ANC decreased in soils with base saturation >10%. At 40–80 cm, ANC remained unchanged in acid‐sensitive soils (base...

A prospective randomized trial of two solutions for intrapartum amnioinfusion: effects on fetal electrolytes, osmolality, and acid-base status.

Science.gov (United States)

Pressman, E K; Blakemore, K J

1996-10-01

Our purpose was to compare the effects of intrapartum amnioinfusion with normal saline solution versus lactated Ringer's solution plus physiologic glucose on neonatal electrolytes and acid-base balance. Patients undergoing amnioinfusion for obstetric indications were randomized to receive normal saline solution or lactated Ringer's solution plus physiologic glucose at standardized amnioinfusion rates. Data were collected prospectively on maternal demographics, course of labor, and maternal and neonatal outcome. Arterial cord blood was obtained for analysis of electrolytes, glucose, osmolality, lactic acid, and blood gases. Control subjects with normal fetal heart rate patterns, and clear amniotic fluid not receiving amnioinfusion were studied concurrently. Data were collected on 59 patients (21 normal saline solution, 18 lactated Ringer's solution plus physiologic glucose, and 20 controls). Maternal demographics, course of labor, and neonatal outcome were similar in all three groups. Cesarean sections were performed more often in the amnioinfusion groups (33.3% for normal saline solution, 38.9% for lactated Ringer's solution plus physiologic glucose) than in the control group (5.0%), p amnioinfusion with either solution. Intrapartum amnioinfusion with normal saline solution or lactated Ringer's solution plus physiologic glucose has no effect on neonatal electrolytes or acid-base balance.

Phase equilibria in a system of aqueous arginine with an octane solution of sulfonic acid

Science.gov (United States)

Kuvaeva, Z. I.; Koval'chuk, I. V.; Vodop'yanova, L. A.; Soldatov, V. S.

2013-05-01

The extraction of arginine (Arg) from aqueous salt (0.1 M NaCl) solutions with a sulfo extractant in a wide range of pH values and amino acid concentrations was studied. The 0.1 M solution of dinonylnaphthalenesulfonic acid (HD) in octane was used as an extractant. The degree of extraction was found to be high at pH 0.8-9.0. This can be explained by the effect of additional intermolecular interactions in the extractant phase involving the guanidine group of Arg.

Corrosion Behaviour of Sn-based Lead-Free Solders in Acidic Solution

Science.gov (United States)

Nordarina, J.; Mohd, H. Z.; Ahmad, A. M.; Muhammad, F. M. N.

2018-03-01

The corrosion properties of Sn-9(5Al-Zn), Sn-Cu and SAC305 were studied via potentiodynamic polarization method in an acidic solution of 1 M hydrochloric acid (HCl). Sn-9(5Al-Zn) produced different polarization profile compared with Sn-Cu and SAC305. The morphological analysis showed that small, deep grooves shaped of corrosion product formed on top of Sn-9(5Al-Zn) solder while two distinctive structures of closely packed and loosely packed corrosion product formed on top of Sn-Cu and SAC305 solder alloys. Phase analysis revealed the formations of various corrosion products such as SnO and SnO2 mainly dominant on surface of solder alloys after potentiodynamic polarization in 1 M hydrochloric acid (HCl).

Limitations when use chloramphenicol-bcyclodextrins complexes in ophtalmic solutions buffered with boric acid/borax system

Directory of Open Access Journals (Sweden)

Todoran Nicoleta

2014-12-01

Full Text Available Chloramphenicol eye drops are commonly prescribed in concentrations of 0.5-1% in the treatment of infectious conjunctivitis. In terms of ophthalmic solution preparation, the major disadvantage of chloramphenicol consists in its low solubility in water. The solubility is increased by substances that form chloramphenicol-complexes, for example: boric acid/borax or cyclodextrins. Objective: Experimental studies aimed to evaluate the potential advantages of enhancing the solubility and stability of chloramphenicol (API by molecular encapsulation in b-cyclodextrin (CD, in formulation of ophthalmic solutions buffered with boric acid/borax system. Methods and Results: We prepared four APIb- CD complexes, using two methods (kneading and co-precipitation and two molar ratio of API/b-cyclodextrin (1:1 and 1:2. The formation of complexes was proved by differential scanning calorimetry (DSC and the in vitro dissolution tests. Using these compounds, we prepared eight ophthalmic solutions, formulated in two variants of chloramphenicol concentrations (0.4% and 0.5%. Each solution was analyzed, by the official methods, at preparation and periodically during three months of storing in different temperature conditions (4°C, 20°C and 30°C. Conclusions: Inclusion of chloramphenicol in b-cyclodextrin only partially solves the difficulties due to the low solubility of chloramphenicol. The protection of chloramphenicol molecules is not completely ensured when the ophthalmic solutions are buffered with the boric acid/borax system.

Calculating the acidity of silanols and related oxyacids in aqueous solution

Science.gov (United States)

Tossell, John A.; Sahai, Nita

2000-12-01

Ab initio molecular orbital theory was used to calculate deprotonation energies and enthalpies (ΔE d, ΔH d) of oxyacid monomers and oligomers. Results were interpreted with reference to current phenomenological models for estimating metal-oxide surface acidities. The ultimate goal is to predict surface acidities using the ab initio method. We evaluated contributions to ΔE d and ΔH d from the electrostatic potential at the proton, electronic relaxation, geometric relaxation, solvation, and polymerization for the neutral-charge gas-phase molecules H 2O, CH 3OH, HCOOH, SiH 3OH, Si(OH) 4, Si 2O 7H 6, H 3PO 4, P 2O 7H 4, H 2SO 3, H 2SO 4, HOCl, HClO 4, Ge(OH) 4, As(OH) 3, and AsO(OH) 3. ΔE d, gas calculated at the modest 6-31G∗ HF of theory level correlates well with experimental pK a in solution, because hydration enthalpies for the acid anions (ΔH hyd, A-) are closely proportional to ΔE d, gas. That is, anion interaction energies with water in aqueous solution and with H + in the gas phase are closely correlated. Correction for differential hydration between an acid and its conjugate base permits generalization of the ΔE d, gas - pK a correlation to deprotonation reactions involving charged acids. Thus, stable protonated, neutral, and deprotonated species Si(OH) 3(OH 2) 1+, Si(OH) 40, Si(OH) 3O 1-, and Si(OH) 2O 22- have been characterized, and solution pK a's for Si(OH) 3(OH 2) 1+ and Si(OH) 3O 1- were estimated, assuming that the charged species (Si(OH) 3(OH 2) 1+, Si(OH) 3O -1) fit into the same ΔE d, gas - pK a correlation as do the neutral acids. The correlation yields a negative pK a (˜ -5) for Si(OH) 3(OH 2) +1. Calculated ΔE d, gas also correlates well with the degree of O under-bonding evaluated using Brown's bond-length based approach. ΔE d, gas increases along the series HClO 4 - Si(OH) 4 mainly because of increasingly negative potential at the site of the proton, not because of differing electronic or geometric relaxation energies. Thus, pK a

Characterization of a novel sialic acid transporter of the sodium solute symporter (SSS) family and in vivo comparison with known bacterial sialic acid transporters.

Science.gov (United States)

Severi, Emmanuele; Hosie, Arthur H F; Hawkhead, Judith A; Thomas, Gavin H

2010-03-01

The function of sialic acids in the biology of bacterial pathogens is reflected by the diverse range of solute transporters that can recognize these sugar acids. Here, we use an Escherichia coliDeltananT strain to characterize the function of known and proposed bacterial sialic acid transporters. We discover that the STM1128 gene from Salmonella enterica serovar Typhimurium, which encodes a member of the sodium solute symporter family, is able to restore growth on sialic acid to the DeltananT strain and is able to transport [(14)C]-sialic acid. Using the DeltananT genetic background, we performed a direct in vivo comparison of the transport properties of the STM1128 protein with those of sialic acid transporters of the major facilitator superfamily and tripartite ATP-independent periplasmic families, E. coli NanT and Haemophilus influenzae SiaPQM, respectively. This revealed that both STM1128 and SiaPQM are sodium-dependent and, unlike SiaPQM, both STM1128 and NanT are reversible secondary carriers, demonstrating qualitative functional differences in the properties of sialic acid transporters used by bacteria that colonize humans.

Cyclohexanone microfluidic extraction of radioactive perrhenate from acid solutions

Energy Technology Data Exchange (ETDEWEB)

Dalmázio, Ilza [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Oehlke, Elisabeth, E-mail: E.Oehlke@tudelft.nl [Section Radiation and Isotopes for Health, Department of Radiation Science and Technology, Delft University of Technology (Netherlands)

2017-07-01

Several studies have investigated the application of microfluidic devices in extraction processes. A potential use of microfluidic devices is in radionuclide generators based on solvent extraction, as the {sup 188}W/{sup 188}Re generator. The aim of this work is to present the initial results of microfluidic solvent extraction of radioactive perrhenate. Aqueous solutions of ammonium perrhenate at 0.1 mg/mL (in water, HCl or sodium tungstate) were used as feed solution and cyclohexanone as extractant. As a first step, the fluid behaviour inside the glass microchannel was evaluated to reach laminar flow. The second step was the determination of extraction efficiency using thermal neutron activated perrhenate to produce feed solutions. The extraction conditions permitted liquid-liquid contact times as short as 0.5 s. Increasing of the contact time, resulted in a higher extraction efficiency of perrhenate, e.g. 14 % for 0.5 s and 32 % for 1.1 s using a 0.1 mol/L HCl feed solution. The extraction of perrhenate improved also when applying a feed solution with higher acidity, e.g. 52% for 1 mol/L HCl with contact time of 1.1 s. The influence of adding sodium tungstate to the feed solution was also examined. To the best of our knowledge, these are the first results related to perrhenate solvent extraction using a microfluidic device. The usefulness of microfluidic devices to screen extraction conditions was demonstrated making it possible to evaluate the effect of electrolytes on the perrhenate extraction process in a short time-frame. (author)

Cyclohexanone microfluidic extraction of radioactive perrhenate from acid solutions

International Nuclear Information System (INIS)

Dalmázio, Ilza; Oehlke, Elisabeth

2017-01-01

Several studies have investigated the application of microfluidic devices in extraction processes. A potential use of microfluidic devices is in radionuclide generators based on solvent extraction, as the 188 W/ 188 Re generator. The aim of this work is to present the initial results of microfluidic solvent extraction of radioactive perrhenate. Aqueous solutions of ammonium perrhenate at 0.1 mg/mL (in water, HCl or sodium tungstate) were used as feed solution and cyclohexanone as extractant. As a first step, the fluid behaviour inside the glass microchannel was evaluated to reach laminar flow. The second step was the determination of extraction efficiency using thermal neutron activated perrhenate to produce feed solutions. The extraction conditions permitted liquid-liquid contact times as short as 0.5 s. Increasing of the contact time, resulted in a higher extraction efficiency of perrhenate, e.g. 14 % for 0.5 s and 32 % for 1.1 s using a 0.1 mol/L HCl feed solution. The extraction of perrhenate improved also when applying a feed solution with higher acidity, e.g. 52% for 1 mol/L HCl with contact time of 1.1 s. The influence of adding sodium tungstate to the feed solution was also examined. To the best of our knowledge, these are the first results related to perrhenate solvent extraction using a microfluidic device. The usefulness of microfluidic devices to screen extraction conditions was demonstrated making it possible to evaluate the effect of electrolytes on the perrhenate extraction process in a short time-frame. (author)

Efficient saccharification by pretreatment of bagasse pith with ionic liquid and acid solutions simultaneously

International Nuclear Information System (INIS)

Wang, Gang; Zhang, Suping; Xu, Wenjuan; Qi, Wei; Yan, Yongjie; Xu, Qingli

2015-01-01

Highlights: • Bagasse pith was pretreated by BMIMCl solution containing HCl and water. • Hemicellulose was hydrolyzed to reducing sugars by HCl to maximize total sugar yield. • Cellulose was dissolved by BMIMCl and 95% of cellulose recovery was obtained. • The recovered cellulose was disrupted which is conducive to cellulase hydrolysis. • The total sugars yield is 89.9% obtained from pretreatment and cellulase hydrolysis. - Abstract: Hydrolysis of hemicellulose and disruption of cellulose during pretreatment process are conducive to the following cellulase hydrolysis performance. In this work, bagasse pith was first pretreated by 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) solution containing 0–1.2% hydrochloric acid (HCl) and 30% water. The water (30%) added into the acidic ionic liquid (IL) solutions led to an increase in the biomass loading up to a biomass/IL solutions ratio of 1:10 (wt.%). Hemicellulose was hydrolyzed to reducing sugars by HCl and cellulose was dissolved by [BMIM]Cl. In this process, 76.9% of hemicellulose conversion and 95% of cellulose recovery were obtained. The pretreated bagasse pith was then followed by hydrolysis with commercially available enzymes. The effects of pretreatment temperature, reaction time and acid concentration on cellulase hydrolysis of pretreated bagasse pith were investigated. Pretreatment of bagasse pith with [BMIM]Cl solutions containing 1.0% HCl at 120 °C for 30 min resulted in the glucose concentration of 92.3 g/l and yield of 94.5% after 72 h of cellulase hydrolysis. The maximum total reducing sugars yield reached to 89.9% after pretreatment and cellulase hydrolysis

Addition and elimination kinetics in OH radical induced oxidation of phenol and cresols in acidic and alkaline solutions

International Nuclear Information System (INIS)

Roder, M.; Wojnarovits, L.; Foeldiak, G.; Emmi, S.S.; Beggiato, G.; D'Angelantonio, M.

1999-01-01

The rates of the two consecutive reactions, OH radical addition and H 2 O/OH - elimination, were studied by pulse radiolysis in highly acidic (pH=1.3-1.9) and alkaline (pH∼11) solutions, respectively, for phenol and for the three cresol isomers. The rate coefficient of the addition as measured by the build-up of phenoxyl radical absorbance and by a competitive method is the same (1.4±0.1)x10 10 mol -1 dm 3 s -1 both in acidic and alkaline solution. The rate coefficient of the H 2 O elimination in acidic solution is (1.6±0.2)x10 6 s -1 , whereas the coefficient of the OH - elimination in alkaline solutions is 6-8 times higher. The kinetics of the phenoxyl radical formation was described by the two-exponential equation of the consecutive reactions: the first exponential is related to the pseudo-first-order addition, while the second to the elimination reaction. No considerable structure dependence was found in the rate coefficients, indicating that the methyl substitutent in these highly acidic or alkaline solutions influences neither the addition nor the elimination rate

Zinc-Nickel Codeposition in Sulfate Solution Combined Effect of Cadmium and Boric Acid

Directory of Open Access Journals (Sweden)

Y. Addi

2011-01-01

Full Text Available The combined effect of cadmium and boric acid on the electrodeposition of zinc-nickel from a sulfate has been investigated. The presence of cadmium ion decreases zinc in the deposit. In solution, cadmium inhibits the zinc ion deposition and suppresses it when deposition potential value is more negative than −1.2 V. Low concentration of CdSO4 reduces the anomalous nature of Zn-Ni deposit. Boric acid decreases current density and shifts potential discharge of nickel and hydrogen to more negative potential. The combination of boric acid and cadmium increases the percentage of nickel in the deposit. Boric acid and cadmium.

NMR 11B, 19F of hydroxofluoroborate solutions in acetic and peracetic acids

International Nuclear Information System (INIS)

Shchetinina, G.P.; Brovkina, O.V.; Chernyshov, B.N.

1985-01-01

Hydroxofluoroborate solutions in acetic and peracetic acids are studied by the 11 B, 19 F NMR method. The reactions of substitutions of acetate- and peracetate ions for nucleophilic hydroxogroups with the formation of the respective complexes are shown to occur in these solutions, with monodentate coordination of BF 3 CH 3 COO - - and BF 3 CH 3 COOO - - groups being accomplished in this case

Solution blow spun Poly(lactic acid)/Hydroxypropyl methylcellulose nanofibers with antimicrobial properties

Science.gov (United States)

Poly(lactic acid) (PLA) nanofibers containing hydroxypropyl methylcellulose (HPMC) and tetracycline hydrochloride (THC) were solution blow spun from two different solvents, chloroform/acetone (CA, 80:20 v/v) and 2,2,2-triflouroethanol (TFE). The diameter distribution, chemical, thermal, thermal stab...

Liquid crystalline solutions of cellulose in phosphoric acid for preparing cellulose yarns

NARCIS (Netherlands)

Boerstoel, H.

2006-01-01

The presen thesis describes a new process for manufacturing high tenacity and high modulus cellulose yarns. A new direct solvent for cellulose has been discovered, leading to liquid crystalline solutions. This new solvent, superphosphoric acid, rapidly dissolves cellulose. These liquid crystalline

The influence of temperature on the decomposition kinetics of peracetic acid in solutions

OpenAIRE

Kunigk, L.; Gomes, D.R.; Forte, F.; Vidal, K.P.; Gomes, L.F.; Sousa, P.F.

2001-01-01

Peracetic acid is a powerful sanitizer that has only recently been introduced in the Brazilian food industry. The main disadvantage of this sanitizer is its decomposition rate. The main purpose of this paper is to present results obtained in experiments carried out to study the decomposition kinetics of peracetic acid in aqueous solutions at 25, 35, 40 and 45 °C. The decompositon of peracetic acid is a first-order reaction. The decomposition rate constants are between 1.71x10-3 h -1 for 25 °C...

A decade of monitoring at Swiss Long-Term Forest Ecosystem Research (LWF) sites: can we observe trends in atmospheric acid deposition and in soil solution acidity?

Science.gov (United States)

Pannatier, Elisabeth Graf; Thimonier, Anne; Schmitt, Maria; Walthert, Lorenz; Waldner, Peter

2011-03-01

Trends in atmospheric acid deposition and in soil solution acidity from 1995 or later until 2007 were investigated at several forest sites throughout Switzerland to assess the effects of air pollution abatements on deposition and the response of the soil solution chemistry. Deposition of the major elements was estimated from throughfall and bulk deposition measurements at nine sites of the Swiss Long-Term Forest Ecosystem Research network (LWF) since 1995 or later. Soil solution was measured at seven plots at four soil depths since 1998 or later. Trends in the molar ratio of base cations to aluminum (BC/Al) in soil solutions and in concentrations and fluxes of inorganic N (NO(3)-N + NH(4)-N), sulfate (SO(4)-S), and base cations (BC) were used to detect changes in soil solution chemistry. Acid deposition significantly decreased at three out of the nine study sites due to a decrease in total N deposition. Total SO(4)-S deposition decreased at the nine sites, but due to the relatively low amount of SO(4)-S load compared to N deposition, it did not contribute to decrease acid deposition significantly. No trend in total BC deposition was detected. In the soil solution, no trend in concentrations and fluxes of BC, SO(4)-S, and inorganic N were found at most soil depths at five out of the seven sites. This suggests that the soil solution reacted very little to the changes in atmospheric deposition. A stronger reduction in base cations compared to aluminum was detected at two sites, which might indicate that acidification of the soil solution was proceeding faster at these sites.

Impedance and hydrogen evolution studies on magnesium alloy in oxalic acid solution containing different anions

Energy Technology Data Exchange (ETDEWEB)

Fekry, A.M. [Chemistry Department, Faculty of Science, Cairo University, Giza 12613 (Egypt)

2010-12-15

The corrosion behavior of AZ31E alloy was investigated in oxalic acid solution using different electrochemical techniques. The effect of concentration was studied, where the corrosion rate was found to increase with increasing oxalic acid concentration and hydrogen evolution. The effect of adding Cl{sup -}, F{sup -} or PO{sub 4}{sup 3-} ions on the electrochemical behavior of AZ31E electrode was studied in 0.01 M oxalic acid solution at 298 K. It was found that the corrosion rate increases with increasing Cl{sup -} or F{sup -} ion concentration, however, it decreases with increasing PO{sub 4}{sup 3-} ion concentration. Good agreement was observed between the results obtained from electrochemical techniques and confirmed by Scanning electron micrographs. (author)

Effect of nitrate on corrosion of austenitic stainless steel in boiling nitric acid solution containing chromium ions

International Nuclear Information System (INIS)

Hasegawa, Satoshi; Kim, Seong-Yun; Ebina, Tetsunari; Ito, Tatsuya; Nagano, Nobumichi; Hitomi, Keitaro; Ishii, Keizo; Tokuda, Haruaki

2016-01-01

The oxidation behavior of chromium and the corrosion behavior of austenitic stainless steel in boiling nitric acid solution containing highly concentrated nitrates were investigated using UV-visible spectroscopic measurements, Raman spectral measurements, immersion tests, and potentiodynamic polarization measurements. The oxidation rate measurement of chromium from Cr(III) to Cr(VI) was performed by 1 M boiling nitric acid solution containing each highly concentrated nitrates: Al(NO_3)_3, Nd(NO_3)_3, Ca(NO_3)_2, Mg(NO_3)_2, and NaNO_3 as a simulant of uranium nitrate in uranium concentrator in reprocessing plants. As a result, the rate of chromium oxidation was different depending on the added nitrates even at the same nitric acid concentration. In addition, the oxidation rate of chromium was increased with increasing the calculated partial pressure of nitric acid in consideration of the hydration of cation of nitrates. Furthermore, the corrosion rate of type 310 stainless steel was accelerated by the solution having a high chromium oxidation rate containing nitrates. These results indicated that the acceleration of the corrosion rate in the solutions depending on the oxidation rate of chromium, and the rate is affected by the salt-effect of nitrates. (author)

A histological comparison of 50% and 70% glycolic acid peels using solutions with various pHs

NARCIS (Netherlands)

Becker, F. F.; Langford, F. P.; Rubin, M. G.; Speelman, P.

1996-01-01

BACKGROUND: Seventy percent glycolic acid solutions are being commonly used as superficial chemical peeling agents. The pH of these solutions ranges from 0.08 to 2.75. The histologic effects of these various pH solutions on human skin have not been studied. OBJECTIVE: The histologic effects of

Corrosion behavior of ODS steels with several chromium contents in hot nitric acid solutions

Science.gov (United States)

Tanno, Takashi; Takeuchi, Masayuki; Ohtsuka, Satoshi; Kaito, Takeji

2017-10-01

Oxide dispersion strengthened (ODS) steel cladding tubes have been developed for fast reactors. Tempered martensitic ODS steels with 9 and 11 wt% of chromium (9Cr-, 11Cr-ODS steel) are the candidate material in research being carried out at JAEA. In this work, fundamental immersion tests and electrochemical tests of 9 to 12Cr-ODS steels were systematically conducted in various nitric acid solutions at 95 °C. The corrosion rate decreased exponentially with effective solute chromium concentration (Creff) and nitric acid concentration. Addition of vanadium (V) and ruthenium (Ru) also decreased the corrosion rate. The combination of low Creff and dilute nitric acid could not avoid the active mass dissolution during active domain at the beginning of immersion, and the corrosion rate was high. Higher Creff decreased the partial anodic current during the active domain and assisted the passivation of the surface of the steel. Concentrated nitric acid and addition of Ru and V increased partial cathodic current and shifted the corrosion potential to noble side. These effects should have prevented the active mass dissolution and decreased the corrosion rate.

Arsenic removal from acidic solutions with biogenic ferric precipitates

Energy Technology Data Exchange (ETDEWEB)

Ahoranta, Sarita H., E-mail: sarita.ahoranta@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Kokko, Marika E., E-mail: marika.kokko@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Papirio, Stefano, E-mail: stefano.papirio@unicas.it [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Özkaya, Bestamin, E-mail: bozkaya@yildiz.edu.tr [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland); Department of Environmental Engineering, Yildiz Technical University, Davutpasa Campus 34220, Esenler, Istanbul (Turkey); Puhakka, Jaakko A., E-mail: jaakko.puhakka@tut.fi [Department of Chemistry and Bioengineering, Tampere University of Technology, P.O. Box 541, FI-33101 Tampere (Finland)

2016-04-05

Highlights: • Continuous and rapid arsenic removal with biogenic jarosite was achieved at pH 3.0. • Arsenic removal was inefficient below pH 2.4 due to reduced Fe–As co-precipitation. • As(V) had better sorption characteristics than As(III). • Biogenic jarosite adsorbed arsenic more effectively than synthetic jarosite. - Abstract: Treatment of acidic solution containing 5 g/L of Fe(II) and 10 mg/L of As(III) was studied in a system consisting of a biological fluidized-bed reactor (FBR) for iron oxidation, and a gravity settler for iron precipitation and separation of the ferric precipitates. At pH 3.0 and FBR retention time of 5.7 h, 96–98% of the added Fe(II) precipitated (99.1% of which was jarosite). The highest iron oxidation and precipitation rates were 1070 and 28 mg/L/h, respectively, and were achieved at pH 3.0. Subsequently, the effect of pH on arsenic removal through sorption and/or co-precipitation was examined by gradually decreasing solution pH from 3.0 to 1.6 (feed pH). At pH 3.0, 2.4 and 1.6, the highest arsenic removal efficiencies obtained were 99.5%, 80.1% and 7.1%, respectively. As the system had ferric precipitates in excess, decreased arsenic removal was likely due to reduced co-precipitation at pH < 2.4. As(III) was partially oxidized to As(V) in the system. In shake flask experiments, As(V) sorbed onto jarosite better than As(III). Moreover, the sorption capacity of biogenic jarosite was significantly higher than that of synthetic jarosite. The developed bioprocess simultaneously and efficiently removes iron and arsenic from acidic solutions, indicating potential for mining wastewater treatment.

Laser-induced photochemical reaction of aqueous maleic acid solutions containing H2O2

International Nuclear Information System (INIS)

Shimizu, Yuichi; Kawanishi, Shunichi; Suzuki, Nobutake

1995-01-01

Hydroxy acid such as glycolic, tartaric and malic acids was directly produced by XeF-laser irradiation of the N 2 -saturated maleic acid aqueous solution containing H 2 O 2 . The selectivities of these products at the maximum of tartaric acid were 71, 4, and 2% at H 2 O 2 feeding rate of 3.2 ml h -1 , respectively. On the other hand, the irradiation of maleates such as dipotassium, calcium, and disodium greatly enhanced the selectivities of tartaric acid formation to 19%, and of malic acid formation to 13%, respectively, for dipotassium maleate. It may be considered from these results that the stability of the hydroxylated intermediate radical plays an important role for the efficient formations of tartaric and malic acids. (author)

Absorption and emission behaviour of trans- p-coumaric acid in aqueous solutions and some organic solvents

Science.gov (United States)

Putschögl, M.; Zirak, P.; Penzkofer, A.

2008-01-01

The absorption and fluorescence behaviour of trans- p-coumaric acid ( trans-4-hydroxycinnamic acid) is investigated in buffered aqueous solution over a wide range from pH 1 to pH 12, in un-buffered water, and in some organic solvents. Absorption cross-section spectra, fluorescence quantum distributions, fluorescence quantum yields, and degrees of fluorescence polarisation are measured. p-Coumaric acid exists in different ionic forms in aqueous solution depending on the pH. There is an equilibrium between the neutral form ( p-CAH 2) and the single anionic form ( p-CAH -) at low pH (p Kna ≈ 4.9), and between the single anionic and the double anionic form ( p-CA 2-) at high pH (p Kaa ≈ 9.35). In the organic solvents studied trans- p-coumaric acid is dissolved in its neutral form. The fluorescence quantum yield of trans- p-coumaric acid in aqueous solution is ϕF ≈ 1.4 × 10 -4 for the neutral and the single anionic form, while it is ϕF ≈ 1.3 × 10 -3 for the double anionic form. For trans- p-coumaric acid in organic solvents fluorescence quantum yields in the range from 4.8 × 10 -5 (acetonitrile) to 1.5 × 10 -4 (glycerol) were measured. The fluorescence spectra are 7700-10,000 cm -1 Stokes shifted in aqueous solution, and 5400-8200 cm -1 Stokes shifted in the studied organic solvents. Decay paths responsible for the low fluorescence quantum yields are discussed (photo-isomerisation and internal conversion for p-CA 2-, solvent-assisted intra-molecular charge-transfer or ππ ∗ to nπ ∗ transfer and internal conversion for p-CAH 2 and p-CAH -). The solvent dependence of the first ππ ∗ electronic transition frequency and of the fluorescence Stokes shift of p-CAH 2 is discussed in terms of polar solute-solvent interaction effects. Thereby the ground-state and excite-state molecular dipole moments are extracted.

Absorption and emission behaviour of trans-p-coumaric acid in aqueous solutions and some organic solvents

International Nuclear Information System (INIS)

Putschoegl, M.; Zirak, P.; Penzkofer, A.

2008-01-01

The absorption and fluorescence behaviour of trans-p-coumaric acid (trans-4-hydroxycinnamic acid) is investigated in buffered aqueous solution over a wide range from pH 1 to pH 12, in un-buffered water, and in some organic solvents. Absorption cross-section spectra, fluorescence quantum distributions, fluorescence quantum yields, and degrees of fluorescence polarisation are measured. p-Coumaric acid exists in different ionic forms in aqueous solution depending on the pH. There is an equilibrium between the neutral form (p-CAH 2 ) and the single anionic form (p-CAH - ) at low pH (pK na ∼ 4.9), and between the single anionic and the double anionic form (p-CA 2- ) at high pH (pK aa ∼ 9.35). In the organic solvents studied trans-p-coumaric acid is dissolved in its neutral form. The fluorescence quantum yield of trans-p-coumaric acid in aqueous solution is φ F ∼ 1.4 x 10 -4 for the neutral and the single anionic form, while it is φ F ∼ 1.3 x 10 -3 for the double anionic form. For trans-p-coumaric acid in organic solvents fluorescence quantum yields in the range from 4.8 x 10 -5 (acetonitrile) to 1.5 x 10 -4 (glycerol) were measured. The fluorescence spectra are 7700-10,000 cm -1 Stokes shifted in aqueous solution, and 5400-8200 cm -1 Stokes shifted in the studied organic solvents. Decay paths responsible for the low fluorescence quantum yields are discussed (photo-isomerisation and internal conversion for p-CA 2- , solvent-assisted intra-molecular charge-transfer or ππ* to nπ* transfer and internal conversion for p-CAH 2 and p-CAH - ). The solvent dependence of the first ππ* electronic transition frequency and of the fluorescence Stokes shift of p-CAH 2 is discussed in terms of polar solute-solvent interaction effects. Thereby the ground-state and excite-state molecular dipole moments are extracted

DORMANCY BREAKING OF OIL PALM SEED TENERA VARIETY BY SOAKING FOR A CERTAIN LENGTH OF TIME IN THE SULFURIC ACID SOLUTION

Directory of Open Access Journals (Sweden)

WAYAN SUENA

2012-11-01

Full Text Available The experiment aimed to know the effect of length of soaked time in sulfuric acid (H2SO4 solution to the dormancy breaking upon the oil palm seeds. The experiment show that soaking seeds for 12 and 10 minutes in the acid solution resulted dormancy breaking were reached after 61.3 days, while soaking seed for 2 minutes in the same solution breaking of dormancy was reached after 73.5 days. By soaked oil palm seeds in sulfuric acid solution gave highest germination percentage (80%, peak value of germination was 0.77%/day, by an average of 0.73%/day. So that, by soaked oil palm seed in sulfuric acid solution for 12 minutes was able to increase vigor, viability, rate of germination and growth uniformity.

49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed in...

Thermodynamic studies on corrosion inhibition of aqueous solutions of amino/carboxylic acids toward copper by EMF measurement

International Nuclear Information System (INIS)

Spah, Manjula; Spah, Dal Chand; Deshwal, Balraj; Lee, Seungmoon; Chae, Yoon-Keun; Park, Jin Won

2009-01-01

Electromotive force (E) measurements were made on an electrochemical cell [Cu x Hg|CuCl 2 (m) in a solvent S|AgCl-Ag] (where S is a dilute aqueous solution (0.01 m) of amino acid (glycine, alanine, methionine and glutamic acid) or aliphatic carboxylic acid (formic acid, acetic acid, n-butyric acid and glutaric acid)) at 30 deg. C. These measured E values were used to compute the dissociation constants (K 1 and K 2 ) and the degree of dissociation (α 1 and α 2 ) by iterative procedures. The standard cell potential (E o ) and the mean activity coefficient (γ ± ) of CuCl 2 were also determined. The E o data were next used to evaluate the Gibbs energy of transfer (ΔG tr 0 ) of CuCl 2 from water to dilute aqueous solutions of the amino/carboxylic acids. The negative ΔG tr 0 values suggested that these acids act as potential corrosion inhibitors. The magnitudes of ΔG tr 0 values show that the amino acids act as better corrosion inhibitors towards copper than the aliphatic carboxylic acids.

Acetanilide interaction with hydriodic acid in aqueous solutions at 20 and 40 deg C

International Nuclear Information System (INIS)

Erkasov, R.Sh.; Nurakhmetov, N.I.

1990-01-01

Isothermal method was used to study acetanilide solubility in aqueous solutions of hydriodic acid at 20 and 40 deg C. formation of two new anhydrous compounds of 2:1 and 1:1 compositions (anilide: acid molar ratio) was established. Temperature and concentration boundaries of solid phase formation were established for these compounds. Their IR spectroscopic investigation was conducted

The structure and diffusion behaviour of the neurotransmitter γ-aminobutyric acid (GABA) in neutral aqueous solutions

International Nuclear Information System (INIS)

Rodrigo, M.M.; Esteso, M.A.; Barros, M.F.; Verissimo, L.M.P.; Romero, C.M.; Suarez, A.F.; Ramos, M.L.; Valente, A.J.M.; Burrows, H.D.; Ribeiro, A.C.F.

2017-01-01

Highlights: • Diffusion coefficients and densities of binary aqueous solutions of γ-aminobutyric acid (GABA). • Dependence on both shape and size of GABA on its diffusion. • Interactions intramolecular and the solute-water interactions in these systems. - Abstract: GABA (γ-aminobutyric acid) is a non-protein amino acid with important physiological properties, and with considerable relevance to the food and pharmaceutical industries. Particular interest has focused on its role as an inhibitory neurotransmitter in the mammalian cerebral cortex. In this paper, we report density and mutual diffusion coefficients of GABA in non-buffered aqueous solutions (0.001–0.100) mol·dm −3 at 298.15 K. Under these conditions, 1 H and 13 C NMR spectroscopy and pH measurements show that it is present predominantly as a monomeric zwitterionic species. Diffusion coefficients have been computed assuming that this behaves as the binary system GABA/water. From density and intermolecular diffusion coefficients measurements, the molar volume, hydrodynamic radii, R h , diffusion coefficients at infinitesimal concentration, D 0 , activity coefficients and the thermodynamic factors, F T , have been estimated. Within experimental error, the hydrodynamic volume calculated from this is identical to the molar volume obtained from density measurements. From the NMR spectra and literature data, it is suggested that this amino acid diffuses in aqueous solution as a curved, coil-like hydrated zwitterionic entity.

Synthesis of highly ordered TiO2 nanotube in malonic acid solution by anodization.

Science.gov (United States)

Ryu, Won Hee; Park, Chan Jin; Kwon, Hyuk Sang

2008-10-01

We synthesized TiO2 nanotube array by anodizing in a solution of malonic acid (HOOCCH2COOH) and NH4F, and analyzed the morphology of the nanotube using scanning electron microscopy (SEM). The morphology of TiO2 nanotube was largely affected by anodizing time, anodizing voltage, and malonic acid concentration. With increasing the anodizing voltage from 5 V to 20 V, the diameter of TiO2 nanotube was increased from about 20 nm to 110 nm and its length from about 10 nm to 700 nm. In addition, the length of TiO2 nanotube was increased with increasing anodizing time up to 6 h at 20 V. We obtained the longest and the most highly ordered nanotube structure when anodizing Ti in a solution of 0.5 wt% NH4F and 1 M malonic acid at 20 V for 6 h.

Radiochromic liquid solution

International Nuclear Information System (INIS)

Noakes, J.E.; Culp, R.A.

1983-01-01

A radiochromic solution which is sensitive to small dosages of ionizing and ultraviolet radiation is described. It consists of a solution of a leucocyanide dye in a clear polar solvent with enough organic acid added to make the solution at least slightly acidic and responds to radiation by permanently changing color. Up to one half of the solution by weight can be replaced by a second solution of an aromatic solvent and an organic fluor. Another modification of the invention is a solution of a leucocyanide dye in a clear polar solvent having an aromatic group, an organic fluor, and enough organic acid to make the solution at least slightly acidic. (author)

Solution thermodynamics of pyrazinamide, isoniazid, and p-aminobenzoic acid in buffers and octanol

International Nuclear Information System (INIS)

Blokhina, Svetlana V.; Ol’khovich, Marina V.; Sharapova, Angelica V.; Volkova, Tatyana V.; Perlovich, German L.

2015-01-01

Highlights: • Solubility of pyrazinamide, isoniazid, p-aminobenzoic acid were measured. • The activity coefficients of the compounds at infinite dilution were determined. • Thermodynamic functions of dissolution and solvation were calculated. - Abstract: The solubility values of pyrazinamide, isoniazid, and p-aminobenzoic acid in buffers (pH 2.0 and 7.4) and octanol were measured in the temperature range of 293.15 to 313.15 K. The dissolution Gibbs energy, enthalpy, and entropy were calculated. The dissolving process was endothermic and enthalpy-determined. The activity coefficients of the compounds at infinite dilution were determined based on the solubility data and thermophysical parameters. A positive deviation from the ideality was observed in all the solutions. A common tendency of the solubility increase with a decrease in the activity coefficients at T = 298.15 K was revealed for the investigated solute-solvent systems. The excess thermodynamic solubility functions were calculated from the temperature dependences of the activity coefficients. The solvation processes were found to have a considerable influence on the solubility of the substances in solutions studied.

The photochemistry of neptunium in aqueous perchloric acid solutions

International Nuclear Information System (INIS)

Friedman, H.A.; Toth, L.M.; Osborne, M.M.

1979-01-01

The photochemistry of neptunium ions in aqueous perchloric acid has been investigated using 254 and 300 nm UV radiation. In the absence of other reagents, Np(IV) and (V) oxidized to Np(VI), in a stepwise fashion, with individual quantum efficiencies for each step that vary from 0.02 to 0.004. Decreasing acid concentration favors the Np(IV) → Np(V) reaction whereas it hinders the Np(V) → Np(VI) photo-oxidation. When ethanol, acetaldehyde and other mild reducing agents are added to neptunium-perchloric acid solutions which are then photolyzed, the Np species are reduced to Np(III) in a stepwise fashion with individual quantum efficiencies that vary from 0.07 to 0.006. The overall photoredox reactions of neptunium are subject to competing secondary product reactions that become significant as the photolysis products accumulate. Absorption spectrophotometry was used to monitor the changes in Np oxidation states and reference spectra of the various Np oxidation states are given for 1.0 N HClO 4 . The Np species have absorption bands in the 300 to 1320 nm region that obey Beer's law only when they were properly resolved. (author)

Metabolic Engineering of Yeast to Produce Fatty Acid-derived Biofuels: Bottlenecks and Solutions

Directory of Open Access Journals (Sweden)

Jiayuan eSheng

2015-06-01

Full Text Available Fatty acid-derived biofuels can be a better solution than bioethanol to replace petroleum fuel, since they have similar energy content and combustion properties as current transportation fuels. The environmentally friendly microbial fermentation process has been used to synthesize advanced biofuels from renewable feedstock. Due to their robustness as well as the high tolerance to fermentation inhibitors and phage contamination, yeast strains such as Saccharomyces cerevisiae and Yarrowia lipolytica have attracted tremendous attention in recent studies regarding the production of fatty acid-derived biofuels, including fatty acids, fatty acid ethyl esters, fatty alcohols, and fatty alkanes. However, the native yeast strains cannot produce fatty acids and fatty acid-derived biofuels in large quantities. To this end, we have summarized recent publications in this review on metabolic engineering of yeast strains to improve the production of fatty acid-derived biofuels, identified the bottlenecks that limit the productivity of biofuels, and categorized the appropriate approaches to overcome these obstacles.

Pseudomacrocyclic effect in extraction processes of metal salts by polyethers from nitric acid solutions

International Nuclear Information System (INIS)

Yakshin, V.V.; Vilkova, O.M.; Kotlyar, S.A.; Kamalov, G.L.

1997-01-01

Comparison of macrocyclic (ME) and pseudmacrocyclic effects (PME), originating by conduct of the metal salt extraction processes (Cs, Sr, In, Zr, Cd, etc) from nitric acid solutions through linear and cyclic polyethers, containing 5 or 6 atoms of ether oxygen and having close molecular masses (290-360), is carried out. It is shown that ordinary ethers practically do not extract the studied metals from nitric acid solutions. By transfer from linear polyethers to their macrocyclic analogs the ME impact is expressed clearly enough: the separation coefficient value grows by tens and hundred times. At the some time the PME role in the extraction processes of metal nitrates through crown-ethers with alkyl and groups is expressed less clearly

Protonation of D-gluconate and its complexation with Np(V) in acidic to nearly neutral solutions

International Nuclear Information System (INIS)

Zhang, Z.; Clark, S.B.; Tian, G.; Rao, L.; Zanonato, P.L.

2006-01-01

Thermodynamic properties of the protonation of D-gluconic acid (HGH 4 (aq)) and its complexation with Np(V) have been studied in acidic to nearly neutral solutions at t = 25 C and I = 1 M NaClO 4 by potentiometry, spectrophotometry and calorimetry. The protonation constant (log K H ) and enthalpy (ΔH H ) of the carboxylate group are determined to be (3.30 ± 0.10) and -(4.03 ± 0.07) kJ mol -1 , respectively. Gluconate forms two Np(V) complexes in nearly neutral solutions. The formation constants and enthalpies of complexation are: log β 1 = (1.48 ± 0.03) and ΔH 1 = -(7.42 ± 0.13) kJ mol -1 for NpO 2 (GH 4 )(aq), log β = (2.14 ± 0.09) and ΔH 2 = -(12.08 ± 0.45) kJ mol -1 for NpO 2 (GH 4 ) 2 - . The thermodynamic parameters indicate that gluconic acid, like isosaccharinic acid and other α-hydroxycarboxylic acids, is a slightly stronger acid and forms stronger complexes with Np(V) than simple monocarboxylic acids. (orig.)

Contribution to the study of the redox couple Np(VI)/Np(V) in the presence of uranium(VI) in solutions of nitric acid and nitrous acid; Contribution a l'etude du comportement redox du couple Np(VI)/Np(V) en presence d'uranium VI dans les solutions constituees d'acide nitrique et d'acide nitreux

Energy Technology Data Exchange (ETDEWEB)

Arpigny, S. [CEA Marcoule, Dept. de Radiochimie et Procedes, DRP, 30 (France)

2001-07-01

The redox behavior of the Np(VI)/Np(V) couple was the subject of a spectrometric study of the Np(VI) reduction reaction in nitric acid solutions (4 to 5 M) containing variable concentrations (1.5 to 3.5 x 10{sup -3} M) of nitrous acid. A low nitrous acid concentration and a high nitric acid concentration were found to favor the stabilization of Np(VI). The stoichiometric coefficients of nitrous acid and nitric acid in the Np(VI) reduction reaction were determined thermodynamically, although only the reaction order with respect to HNO{sub 2} could be calculated from a kinetic analysis. Adding nitrate ions to a HNO{sub 3}/HNO{sub 2} solution enhanced the stability of neptunium at oxidation state +VI, but also increased the reduction rate. When uranium(VI) was added to the HNO{sub 3}/HNO{sub 2} solutions, the total quantity of neptunium at oxidation state +V (either free or as a Np(V)-U(VI) complex) remained practically unchanged, as did the Np(VI) reduction rate. The electrochemical behavior of the Np(VI)/Np(V) couple was investigated in a weak acidic medium by voltammetry with an ultra-micro-electrode (UME). The oxidation wave limiting current variation was a linear function of the Np(V) concentration when a gold UME was used, but not with a platinum UME; the reduction wave limiting current variation versus the Np(V) concentration was linear with either gold or platinum UMEs. The presence of the Np(V)-U(VI) complex in the neptunium solutions was characterized by a shift in the normal apparent potential of the Np(VI)/Np(V) couple toward anodic potentials consistent with the previously determined values of the complexation constants. (author)

Electrochemical behavior of Ti and Ti6Al4V in aqueous solutions of citric acid containing halides

Directory of Open Access Journals (Sweden)

Anelise Marlene Schmidt

2006-12-01

Full Text Available This paper reports on an investigation of the electrochemical behavior of Ti grade 2 and Ti6Al4V alloy in aqueous citric acid solutions with pH 2.0 containing halide ions. Voltammetric studies of Ti and the alloy in citric acid, with and without chloride ions, indicate that the Ti and Ti alloy presented a passive behavior in the test solutions used. Pitting was observed at 3.0 and 2.5 V/SCE for Ti and Ti6Al4V, respectively, when bromide ions were added to the solution. In solutions containing fluoride ions, dissolution of the film occurred at potentials close to - 1.0 V/SCE in both electrodes. The iodide ions oxidized on the passive oxide film at potentials close to 1.0 V/SCE. EIS results of the materials in citric acid solutions containing chloride ions revealed that the film's resistance increased as the applied potential rose from 0 to 1.0 V. In bromide-containing solutions, breakdown of the film was confirmed at potentials above 2.0 V/SCE in both electrodes. These results suggest film reformation for Ti and the alloy in solutions containing fluoride at potentials within the passive region.

Evaluation of ethylenediaminetetraacetic acid (EDTA) solution and gel for smear layer removal.

Science.gov (United States)

Dotto, Sidney Ricardo; Travassos, Rosana Maria Coelho; de Oliveira, Elias Pandonor Motcy; Machado, Manoel Eduardo de Lima; Martins, José Luiz

2007-08-01

The purpose of this in vitro study was to compare the efficacy of 24% ethylenediaminetetraacetic acid (EDTA) gel and 17% EDTA solution in cleaning dentine walls after root canal instrumentation. Thirty human canine teeth were divided into three groups of 10 teeth each. In Group 1, 1% sodium hypochlorite was used as the irrigating solution; in Group 2, 1% sodium hypochlorite was used with 17% EDTA solution; and in Group 3, 1% sodium hypochlorite was used with 24% EDTA gel. The presence of a smear layer was analysed after instrumentation using scanning electron microscopy. The Kruskal-Wallis test revealed a statistical difference (P 0.05). The results indicate that 1% sodium hypochlorite alone does not remove the smear layer and that there was no statistical difference between EDTA gel and EDTA solution in smear layer removal.

The immiscible aqueous solutions of alkyl phosphates. Study for the purpose of uranium extraction from phosphoric acid solutions

International Nuclear Information System (INIS)

Mauborgne, Bernard

1979-01-01

Systems of immiscible aqueous solutions composed by a phase rich in mineral salt and by another phase almost totally containing an organic salt, have been studied for years, with quaternary ammonium salts with an organic cation. The objective of this research is to study systems symmetric to the previous ones, i.e. with organic anions such as alkyl phosphates, and then to try to understand mechanisms of extraction of metals in these environments. Based on properties of immiscible aqueous solutions, an original three-phase process of liquid-liquid extraction has been developed, and is used to separate uranium in phosphoric acids with better performance than the existing industrial processes [fr

Effects of EDTA and low molecular weight organic acids on soil solution properties of a heavy metal polluted soil.

Science.gov (United States)

Wu, L H; Luo, Y M; Christie, P; Wong, M H

2003-02-01

A pot experiment was conducted to study the effects of EDTA and low molecular weight organic acids (LMWOA) on the pH, total organic carbon (TOC) and heavy metals in the soil solution in the rhizosphere of Brassica juncea grown in a paddy soil contaminated with Cu, Zn, Pb and Cd. The results show that EDTA and LMWOA have no effect on the soil solution pH. EDTA addition significantly increased the TOC concentrations in the soil solution. The TOC concentrations in treatments with EDTA were significantly higher than those in treatments with LMWOA. Adding 3 mmol kg(-1) EDTA to the soil markedly increased the total concentrations of Cu, Zn, Pb and Cd in the soil solution. Compared to EDTA, LMWOA had a very small effect on the metal concentrations. Total concentrations in the soil solution followed the sequence: EDTA > citric acid (CA) approximately oxalic acid (OA) approximately malic acid (MA) for Cu and Pb; EDTA > MA > CA approximately OA for Zn; and EDTA > MA > CA > OA for Cd. The labile concentrations of Cu, Zn, Pb and Cd showed similar trends to the total concentrations.

Determination of nitric acid in highly radioactive solutions by the method of coulometric titration

International Nuclear Information System (INIS)

Gromov, V.S.; Kuperman, A.Ya.; Smirnov, Yu.A.

1988-01-01

A procedure, a cell, and an electronic block have been developed for a long-distance determination of nitric acid in highly radioactive industrial solutions by coulometric titration under hot chamber conditions. A solution of a mixture of ammonium and potassium oxalates was used for the background and anoide electrolytes. This solution prevents the hydrolysis of the metal ions and appreciably decreases the rate of accumulation of the acid in the anode chamber of the cell. Titration with 0.1-0.5 A currents is carried out with internal generation of hydroxyl ions. The cell was prepared from a radiation-resistant and transparent material, poly(methyl methacrylate). The anode and cathode chambers were separated by a cellophane membrane, reinforced by a porous glass filter. By using the electronic coulometric block working together with a pH-meter (EV-74 or I-130) and with an automatic titration block (BAT-15), the titration can be carried out automatically, and the determination results can be obtained in a digital form

The extraction of trace amounts of tantalum(V) from different mineral acid solutions by 4-(5-nonyl) pyridine oxide and trioctylamine oxide

International Nuclear Information System (INIS)

Ejaz, M.; Carswell, D.J.

1976-01-01

Data are presented on the distribution of trace amounts of tantalum(V) between different mineral acid solutions and 0.1M solutions of N-oxides of 4-(5-nonyl) pyridine and trioctylamine. The optimal acidity is 0.01-0.5M, depending on the nature of the acid. Common anions have little effect on extraction. Possible mechanism of extraction are suggested making use of slope analysis data. Separation factors for a number of metal ions with respect to tantalum are reported for the 0.1M 4-(5-nonyl)pyridine oxide - 1M sulphuric acid extraction system. Separation from uranium(VI), thorium(IV) and a number of fission products is suggested. The conclusions are unique as follows: Amine oxides are as unique as oxygen-donor extractants in their extraction of tantalum(V) from weakly acid solutions; tantalum is almost completely extracted from weakly nitric, hydrochloric and sulphuric acid solutions by both of the amine oxides; the extraction in low acidity solutions is independent of the nature of the anion of the acids present, indicating the ability of amine oxides to extract the product of hydrolysis of hydrolysable elements. In this respect amine oxides are much better than tributyl phosphate. (T.G.)

Simultaneous pollutant removal and electricity generation in denitrifying microbial fuel cell with boric acid-borate buffer solution.

Science.gov (United States)

Chen, Gang; Zhang, Shaohui; Li, Meng; Wei, Yan

2015-01-01

A double-chamber denitrifying microbial fuel cell (MFC), using boric acid-borate buffer solution as an alternative to phosphate buffer solution, was set up to investigate the influence of buffer solution concentration, temperature and external resistance on electricity generation and pollutant removal efficiency. The result revealed that the denitrifying MFC with boric acid-borate buffer solution was successfully started up in 51 days, with a stable cell voltage of 205.1 ± 1.96 mV at an external resistance of 50 Ω. Higher concentration of buffer solution favored nitrogen removal and electricity generation. The maximum power density of 8.27 W/m(3) net cathodic chamber was obtained at a buffer solution concentration of 100 mmol/L. An increase in temperature benefitted electricity generation and nitrogen removal. A suitable temperature for this denitrifying MFC was suggested to be 25 °C. Decreasing the external resistance favored nitrogen removal and organic matter consumption by exoelectrogens.

Extraction equilibria of amino acids by Di (2-ethylhexyl) phosphoric acid in n-heptane solutions; Di (2-ethylhexyl) rinsan no n-heptane yoeki ni yoru aminosan no chushutsu heiko

Energy Technology Data Exchange (ETDEWEB)

Takahashi, M. [Suzuka National College of Technology, Mie (Japan); Tani, F. [Toyohashi University of Technology, Aichi (Japan); Kawai, Y. [Wako Jyunyaku Co. Ltd., Osaka (Japan); Takeuchi, H. [Nagoya University, Nagoya (Japan). Faculty of Engineering

1997-03-10

The extraction equilibria (i.e., distribution ratio) of amino acids by Di (2-ethyl hexyl) phosphoric acid in n-heptane solutions was investigated at a temperature of 298.2 K in the low pH range (of 2 to 5). The equal amount of an amino acid solution and an extracted solution with the predetermined concentration were shaken using a flask, and the concentration of amino acid in water phase was analyzed by a ninhydrin method. The concentration in organic phase was obtained by the concentration analysis in water phase and the material balance method after the amino acid is back-extracted by solution hydrochloride. The distribution ratio is in inverse proportion to the hydrogen ion concentration and in proportion to the 0.5th power of extracted agent concentration. The equilibrium constant is 0.650, 0.420, 0.320, 0.275, 0.064, and 0.040 mol{sup 0.5}/m{sup 1.5} in L-phenylalanine, L-tryptophane, L-leucine, L-methionine, glycine, and L-alanine, respectively. The equilibrium constant of the largest L-phenylalanine is 16 times as high as the smallest alanine. The extracted equilibrium constant increased as the hydrophobic property of amino acid increases. 18 refs., 10 figs., 1 tab.

Comparing the Titrations of Mixed-Acid Solutions Using Dropwise and Constant-Flow Techniques

Science.gov (United States)

Charlesworth, Paul; Seguin, Matthew J.; Chesney, David J.

2003-11-01

A mixed-acid solution containing hydrochloric and phosphoric acids was used to determine the error associated with performing a real-time titration. The results were compared against those obtained by performing the titration in a more traditional dropwise addition of titrant near the equivalence points. It was found that the real-time techniques resulted in significantly decreased analysis times while maintaining a low experimental error. The constant-flow techniques were implemented into two different levels of chemistry. It was found that students could successfully utilize the modified experiments. Problems associated with the techniques, major sources of error, and their solutions are discussed. In both cases, the use of the constant-flow setup has increased student recollection of key concepts, such as pKa determination, proper indicator choice, and recognizing the shape of specific titration curves by increasing student interest in the experiment.

Absorption and emission behaviour of trans-p-coumaric acid in aqueous solutions and some organic solvents

Energy Technology Data Exchange (ETDEWEB)

Putschoegl, M.; Zirak, P. [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Penzkofer, A. [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany)], E-mail: alfons.penzkofer@physik.uni-regensburg.de

2008-01-22

The absorption and fluorescence behaviour of trans-p-coumaric acid (trans-4-hydroxycinnamic acid) is investigated in buffered aqueous solution over a wide range from pH 1 to pH 12, in un-buffered water, and in some organic solvents. Absorption cross-section spectra, fluorescence quantum distributions, fluorescence quantum yields, and degrees of fluorescence polarisation are measured. p-Coumaric acid exists in different ionic forms in aqueous solution depending on the pH. There is an equilibrium between the neutral form (p-CAH{sub 2}) and the single anionic form (p-CAH{sup -}) at low pH (pK{sub na} {approx} 4.9), and between the single anionic and the double anionic form (p-CA{sup 2-}) at high pH (pK{sub aa} {approx} 9.35). In the organic solvents studied trans-p-coumaric acid is dissolved in its neutral form. The fluorescence quantum yield of trans-p-coumaric acid in aqueous solution is {phi}{sub F} {approx} 1.4 x 10{sup -4} for the neutral and the single anionic form, while it is {phi}{sub F} {approx} 1.3 x 10{sup -3} for the double anionic form. For trans-p-coumaric acid in organic solvents fluorescence quantum yields in the range from 4.8 x 10{sup -5} (acetonitrile) to 1.5 x 10{sup -4} (glycerol) were measured. The fluorescence spectra are 7700-10,000 cm{sup -1} Stokes shifted in aqueous solution, and 5400-8200 cm{sup -1} Stokes shifted in the studied organic solvents. Decay paths responsible for the low fluorescence quantum yields are discussed (photo-isomerisation and internal conversion for p-CA{sup 2-}, solvent-assisted intra-molecular charge-transfer or {pi}{pi}* to n{pi}* transfer and internal conversion for p-CAH{sub 2} and p-CAH{sup -}). The solvent dependence of the first {pi}{pi}* electronic transition frequency and of the fluorescence Stokes shift of p-CAH{sub 2} is discussed in terms of polar solute-solvent interaction effects. Thereby the ground-state and excite-state molecular dipole moments are extracted.

Oxidation of ascorbic acid by a (salen)ruthenium(VI) nitrido complex in aqueous solution.

Science.gov (United States)

Wang, Qian; Man, Wai-Lun; Lam, William W Y; Lau, Tai-Chu

2014-12-25

The oxidation of ascorbic acid (H2A) by [Ru(VI)(N)(L)(MeOH)](+) in aqueous acidic solutions has the following stoichiometry: 2[Ru(VI)(N)] + 3H2A → 2[Ru(III)(NH2-HA)](+) + A. Mechanisms involving HAT/N-rebound at low pH (≤2) and nucleophilic attack at the nitride at high pH (≥5) are proposed.

Inhibitory effect of some carbazides on corrosion of aluminium in hydrochloric acid and sodium hydroxide solutions

Energy Technology Data Exchange (ETDEWEB)

Fouda, A.S. [El-Mansoura Univ. (Egypt). Dept. of Chemistry; Madkour, L.H. [Tanta Univ. (Egypt). Dept. of Chemistry; Elshafei, A.A. [El-Mansoura Univ. (Egypt). Dept. of Chemistry; Elasklany, A.H. [El-Mansoura Univ. (Egypt). Dept. of Chemistry

1995-06-01

The dissolution of aluminium in hydrochloric acid and sodium hydroxide solutions in the presence of semicarbazide, thiosemicarbazide and sym.diphenylcarbazide as corrosion inhibitors has been studied using thermometric, weight-loss and polarization methods. The three methods gave consistent results. The higher inhibition efficiency of these compounds in acidic than in alkaline madia may be due to the less negative potential of aluminium in hydrochloric acid solution, favouring adsorption of the additive. The adsorption of these compounds were found to obey Frumkin adsorption isotherm. Cathodic polarization measurements showed that these compounds are cathodic inhibitors and their adsorption in the double layer does not change the mechanism of the hydrogen evolution reaction. The results are analysed in terms of both molecular and cationic adsorption. (orig.)

A mathematical model for chemical reactions with actinide elements in the aqueous nitric acid solution: REACT

International Nuclear Information System (INIS)

Tachimori, Shoichi

1990-02-01

A mathematical model of chemical reactions with actinide elements: REACT code, was developed to simulate change of valency states of U, Pu and Np in the aqueous nitric acid solution. Twenty seven rate equations for the redox reactions involving some reductants, disproportionation reactions, and radiolytic growth and decay reaction of nitrous acid were programmed in the code . Eight numerical solution methods such as Porsing method to solve the rate equations were incorporated parallel as options depending on the characteristics of the reaction systems. The present report gives a description of the REACT code, e.g., chemical reactions and their rate equations, numerical solution methods, and some examples of the calculation results. A manual and a source file of the program was attached to the appendix. (author)

Sustainable Soil Washing: Shredded Card Filtration of Potentially Toxic Elements after Leaching from Soil Using Organic Acid Solutions.

Directory of Open Access Journals (Sweden)

Christopher Ash

Full Text Available Shredded card (SC was assessed for use as a sorbent of potentially toxic elements (PTE carried from contaminated soil in various leachates (oxalic acid, formic acid, CaCl2, water. We further assessed SC for retention of PTE, using acidified water (pH 3.4. Vertical columns and a peristaltic pump were used to leach PTE from soils (O and A/B horizons before passing through SC. Sorption onto SC was studied by comparing leachates, and by monitoring total PTE contents on SC before and after leaching. SC buffers against acidic soil conditions that promote metals solubility; considerable increases in solution pH (+4.49 were observed. Greatest differences in solution PTE content after leaching with/without SC occurred for Pb. In oxalic acid, As, Cd, Pb showed a high level of sorption (25, 15, and 58x more of the respective PTE in leachates without SC. In formic acid, Pb sorption was highly efficient (219x more Pb in leachate without SC. In water, only Pb showed high sorption (191x more Pb in leachate without SC. In desorption experiments, release of PTE from SC varied according to the source of PTE (organic/mineral soil, and type of solvent used. Arsenic was the PTE most readily leached in desorption experiments. Low As sorption from water was followed by fast release (70% As released from SC. A high rate of Cd sorption from organic acid solutions was followed by strong retention (~12% Cd desorption. SC also retained Pb after sorption from water, with subsequent losses of ≤8.5% of total bound Pb. The proposed use of this material is for the filtration of PTE from extract solution following soil washing. Low-molecular-mass organic acids offer a less destructive, biodegradable alternative to strong inorganic acids for soil washing.

Sustainable Soil Washing: Shredded Card Filtration of Potentially Toxic Elements after Leaching from Soil Using Organic Acid Solutions

Science.gov (United States)

Ash, Christopher; Drábek, Ondřej; Tejnecký, Václav; Jehlička, Jan; Michon, Ninon; Borůvka, Luboš

2016-01-01

Shredded card (SC) was assessed for use as a sorbent of potentially toxic elements (PTE) carried from contaminated soil in various leachates (oxalic acid, formic acid, CaCl2, water). We further assessed SC for retention of PTE, using acidified water (pH 3.4). Vertical columns and a peristaltic pump were used to leach PTE from soils (O and A/B horizons) before passing through SC. Sorption onto SC was studied by comparing leachates, and by monitoring total PTE contents on SC before and after leaching. SC buffers against acidic soil conditions that promote metals solubility; considerable increases in solution pH (+4.49) were observed. Greatest differences in solution PTE content after leaching with/without SC occurred for Pb. In oxalic acid, As, Cd, Pb showed a high level of sorption (25, 15, and 58x more of the respective PTE in leachates without SC). In formic acid, Pb sorption was highly efficient (219x more Pb in leachate without SC). In water, only Pb showed high sorption (191x more Pb in leachate without SC). In desorption experiments, release of PTE from SC varied according to the source of PTE (organic/mineral soil), and type of solvent used. Arsenic was the PTE most readily leached in desorption experiments. Low As sorption from water was followed by fast release (70% As released from SC). A high rate of Cd sorption from organic acid solutions was followed by strong retention (~12% Cd desorption). SC also retained Pb after sorption from water, with subsequent losses of ≤8.5% of total bound Pb. The proposed use of this material is for the filtration of PTE from extract solution following soil washing. Low-molecular-mass organic acids offer a less destructive, biodegradable alternative to strong inorganic acids for soil washing. PMID:26900684

Moessbauer spectroscopic evidence for iron(III) complexation and reduction in acidic aqueous solutions of indole-3-butyric acid

International Nuclear Information System (INIS)

Kovacs, K.; Kuzmann, E.; Vertes, A.; Kamnev, A.A.; Shchelochkov, A.G.; Medzihradszky-Schweiger, H.; Mink, J.; Hungarian Academy of Sciences, Budapest

2004-01-01

Moessbauer spectroscopic studies were carried out in acidic (pH 2.3) 57 Fe III nitrate containing aqueous solutions of indole-3-butyric acid (IBA), rapidly frozen in liquid nitrogen at various periods of time after mixing the reagents. The data obtained show that in solution in the presence of IBA, iron(III) forms a complex with a dimeric structure characterised by a quadrupole doublet, whereas without IBA under similar conditions iron(III) exhibits a broad spectral feature due to a slow paramagnetic spin relaxation which, at liquid nitrogen temperature, results in a large anomalous line broadening (or, at T = 4.2 K, in a hyperfine magnetic splitting). The spectra of 57 Fe III +IBA solutions, kept at ambient temperature under aerobic conditions for increasing periods of time before freezing, contained a gradually increasing contribution of a component with a higher quadrupole splitting. The Moessbauer parameters for that component are typical for iron(II) aquo complexes, thus showing that under these conditions gradual reduction of iron(III) occurs, so that the majority (85%) of dissolved iron(III) is reduced within 2 days. The Moessbauer parameters for the iron(III)-IBA complex in aqueous solution and in the solid state (separated from the solution by filtration) were found to be similar, which may indicate that the dissolved and solid complexes have the same composition and/or iron(III) coordination environment. For the solid complex, the data of elemental analysis suggest the following composition of the dimer: [L 2 Fe-(OH) 2 -FeL 2 ] (where L is indole-3-butyrate). This structure is also in agreement with the data of infrared spectroscopic study of the complex reported earlier, with the side-chain carboxylic group in indole-3-butyrate as a bidentate ligand. The Moessbauer parameters for the solid 57 Fe III -IBA complex at T = 80 K and its acetone solution rapidly frozen in liquid nitrogen were virtually identical, which indicates that the complex retains its

Study of uranium(VI) speciation in phosphoric acid solutions and of its recovery by solvent extraction

International Nuclear Information System (INIS)

Dartiguelongue, Adrien

2014-01-01

Because small amounts of uranium are present in phosphate rocks, wet phosphoric acids may contain up to 300 ppm of uranium(VI). Therefore, such acids are a cost-effective unconventional source of this metal. Its recovery is a challenge for metallurgical firms which must develop reliable and selective solvent extraction processes. Such processes need to know the chemical equilibria involved in the extraction process, the speciation of uranium and its thermodynamics in solution. These two last points have been investigated in this work. Firstly, the most probable species of uranium(VI) in phosphoric acid solutions have been selected thanks to a detailed review of the literature. Then, a thermodynamic model founded on an equation of state for electrolytes has been built according these hypotheses. It has been validated with speciation data coming from original ATR-IR spectroscopy measurements. Finally, the composition of the aqueous phosphoric acid solutions and the activity coefficients obtained have been combined with a chemical model of uranium(VI) extraction into an organic phase containing a synergistic mixture of bis(2-ethylhexyl)phosphoric acid (D2EHPA) and tri-n-octylphosphine oxide (TOPO) in order to represent the variation of the distribution coefficient of uranium(VI) with H 3 PO 4 concentration. This model had been previously developed at Chimie ParisTech at a given concentration of H 3 PO 4 (i.e., 5,3 mol/L), but in the present study we have tested its validity in an extended range of phosphoric acid concentrations (i.e., 1-7 mol/L) and improved it. (author)

Evaluation of the Magnesium Hydroxide Treatment Process for Stabilizing PFP Plutonium/Nitric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Gerber, Mark A.; Schmidt, Andrew J.; Delegard, Calvin H.; Silvers, Kurt L.; Baker, Aaron B.; Gano, Susan R.; Thornton, Brenda M.

2000-09-28

This document summarizes an evaluation of the magnesium hydroxide [Mg(OH)2] process to be used at the Hanford Plutonium Finishing Plant (PFP) for stabilizing plutonium/nitric acid solutions to meet the goal of stabilizing the plutonium in an oxide form suitable for storage under DOE-STD-3013-99. During the treatment process, nitric acid solutions bearing plutonium nitrate are neutralized with Mg(OH)2 in an air sparge reactor. The resulting slurry, containing plutonium hydroxide, is filtered and calcined. The process evaluation included a literature review and extensive laboratory- and bench-scale testing. The testing was conducted using cerium as a surrogate for plutonium to identify and quantify the effects of key processing variables on processing time (primarily neutralization and filtration time) and calcined product properties.

Detection of hypoxanthine, xanthine and uric acid in γ-irradiated aqueous solution of cytosine

International Nuclear Information System (INIS)

Kobayashi, Tsuya; Shirai, Kazuo

1979-01-01

The aqueous solution of cytosine of 3.6 x 10 -2 M was irradiated with gamma -ray (60 megarad) in nitrogen-saturated glass ampules, and freeze-dried, then the residue obtained was changed to trimethylsilylacid, and this was analyzed by paper chromatography, UV spectrometry, and/or gas-liquid chromatography. Hypoxanthine, xanthine and uric acid were detected in this solution, in addition to some other compounds already known to be produced by gamma -irradiation, e.g., TMS-uracil, TMS-6-hydroxyuracil and TMS-hypoxanthine. It was presumed that these compounds were formed by the recombination of the primary radiolytic products. Uric acid formation by this mechanism was confirmed by gamma -irradiation of the mixture that contained urea, and 5- and 6-hydroxyuracil. (Kaihara, S.)

Potentiometric determination of free nitric-acid in trilaurylamine solutions containing plutonium nitrate; Dosage potentiometrique de l'acidite nitrique libre dans les solutions organiques de trilaurylamine

Energy Technology Data Exchange (ETDEWEB)

Perez, J J; Saey, J C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1965-07-01

A potentiometric method of determination of the free nitric acid in trilaurylamine solutions containing plutonium or thorium nitrates is described. The potentiometric titration is carried out in a mixture of benzene and 1,2-dichloro ethane with a standard solution of trilaurylamine as the titrant. When thorium nitrate is present the metal complex is not dissociated then the titration has a single end-point. In the case of plutonium nitrate the partial dissociation of the plutonium complex corresponds to a second point. The experimental error in duplicate analyses of 50 samples is about 1 per cent for free acid concentrations in the range of 0,03 to 0,1 N and plutonium concentrations between 1 to 5 g/l. (authors) [French] Une methode potentiometrique de dosage de l'acidite nitrique libre dans les solutions de trilaurylamine contenant un complexe de plutonium ou de thorium est decrite. La potentiometrie est effectuee en prenant comme base titrante la trilaurylamine et comme milieu de dilution un melange de benzene et de 1,2 dichloroethane. Dans le cas du thorium, le complexe organometallique n'est pas deplace et la courbe de titrage presente un seul point d'inflexion. Dans le cas du plutonium le complexe est partiellement dissocie ce qui correspond a un second saut de potentiel. La moyenne des erreurs experimentales sur 50 echantillons doses a ete d'environ {+-} 1 pour cent sur l'acide libre. Les solutions experimentees contenaient de 0,03 a 0,1 N en acide et de 1 a 5 g/l en plutonium. (auteurs)

A study comparing chemical peeling using modified jessner′s solution and 15% trichloroacetic acid versus 15% trichloroacetic acid in the treatment of melasma

Directory of Open Access Journals (Sweden)

Safoury Omar

2009-01-01

Full Text Available Background: Melasma is a symmetric progressive hyperpigmentation of the facial skin that occurs in all races but has a predilection for darker skin phenotypes. Depigmenting agents, laser and chemical peeling as classic Jessner′s solution, modified Jessner′s solution and trichloroacetic acid have been used alone and in combination in the treatment of melasma. Objectives: The aim of the study was to compare the therapeutic effect of combined 15% Trichloroacetic acid (TCA and modified Jessner′s solution with 15% TCA on melasma. Materials and Methods: Twenty married females with melasma (epidermal type, with a mean age of 38.25 years, were included in this study. All were of skin type III or IV. Fifteen percent TCA was applied to the whole face, with the exception of the left malar area to which combined TCA 15% and modified Jessner′s solution was applied. Results: Our results revealed statistically highly significant difference between MASI Score (Melasma Area and Severity Index between the right malar area and the left malar area. Conclusion: Modified Jessner′s solution proved to be useful as an adjuvant treatment with TCA in the treatment of melasma, improving the results and minimizing postinflammatory hyperpigmentation.

Study on the utilization of a sodium-sulfuric acid solution for the uranium minerals' leaching

International Nuclear Information System (INIS)

Echenique, Patricia; Fruchtenicht, Fernando; Gil, Daniel; Vigo, Daniel; Bouza, Angel; Vert, Gabriela; Becquart, Elena

1988-01-01

Argentine uranium minerals have been leached at bench scale with a different agent trying to reduce sulfuric acid consumption. The leaching agent was a sodium sulfate-sulfuric acid solution and the ore was from Sierra Pintada (San Rafael - Mendoza). The work was performed in stirred vessel at atmospheric pressure. The influence of different variables, pH, temperature, oxidant agent, sodium sulfate concentration and time, in the sulfuric acid consumption and the uranium yield was studied. (Author) [es

PdRu alloy nanoparticles of solid solution in atomic scale: outperformance towards formic acid electro-oxidation in acidic medium

International Nuclear Information System (INIS)

Miao, Kanghua; Luo, Yun; Zou, Jiasui; Yang, Jun; Zhang, Fengqi; Huang, Lin; Huang, Jie; Kang, Xiongwu; Chen, Shaowei

2017-01-01

Developing catalyst of high performance and low cost toward the electro-oxidation of formic acid on the anode of fuel cell is critical for the commercialization of direct formic acid fuel cells. Here we reported the synthesis of Pd x Ru 10-x (x = 1,3,5,7,9) nanoparticles (NPs) by concurrent reduction of Pd 2+ and Ru 2+ in polyol solution at 200 °C. The particle size of the obtained NPs was confined at 5–15 nm in diameter. X-ray diffraction (XRD) analysis revealed face-centered cubic (fcc) crystal structure for Pd x Ru 10-x (x = 3,5,7,9), with the lattice parameter proportional to the Pd content. The formation of the solid solution in atomic scale was confirmed for the alloy nanoparticles by XRD and the elemental mapping. Williamson-Hall method revealed that the stacking fault was dependent on the alloying extent of the alloy nanoparticles and reached the minimum for Pd 5 Ru 5 , which exhibited the highest activity towards formic acid oxidation among all these prepared samples, with mass activity of 12.6 times higher than that of commercial Pd/C. It was observed that the highest catalytic activity was in agreement with the minimum of the stacking fault of the alloy nanoparticles.

Thermodynamics of uranium and nitric acid extraction from aqueous solution of TBP/diluent

International Nuclear Information System (INIS)

Souza Freitas, R.F. de.

1982-06-01

A thermodynamically consistent procedure for predicting distribution equilibria for uranyl nitrate and nitric acid between an aqueous solution and 30 vol % tributyl phosphate (TBP) in a hydrocarbon diluent is studied. Experimental work is developed in order to obtain equilibrium data for the system uranyl nitrate, nitric acid, water and 30 vol % TBP in n-dodecane, at 25 0 C and 40 0 C. The theoretical equilibrium data, obtained with the aid of a computer, are compared with the experimental results. (Author) [pt

Pulse electrodeposition of Pt and Pt–Ru methanol-oxidation nanocatalysts onto carbon nanotubes in citric acid aqueous solutions

Energy Technology Data Exchange (ETDEWEB)

Chou, Huei-Yu [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Hsieh, Chien-Kuo [Department of Materials Engineering, Ming Chi University of Technology, New Taipei City 24301, Taiwan, ROC (China); Tsai, Ming-Chi; Wei, Yu-Hsuan; Yeh, Tsung-Kuang [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China); Tsai, Chuen-Horng, E-mail: tsai@aec.gov.tw [Department of Engineering and System Science, National Tsing Hua University, Hsinchu 30013, Taiwan, ROC (China)

2015-06-01

In this study, platinum nanoparticle/carbon nanotube (Pt NP/CNT) and platinum–ruthenium nanoparticle (Pt–Ru NP/CNT) hybrid nanocatalysts were prepared by the pulse-electrodeposition method in different aqueous solutions containing citric acid (CA) or sulfuric acid (SA). The electrocatalytic properties of the Pt NP/CNT and Pt–Ru NP/CNT electrodes prepared using different aqueous solutions were investigated for methanol oxidation. The results show that the electrochemical mass activities of these hybrid nanocatalysts prepared in the CA aqueous solution were increased by factors of 1.46 and 2.77 for Pt NPs and Pt–Ru NPs, respectively, compared with those prepared in SA aqueous solutions using the same procedure. These increased mass activities are attributed to the CA playing dual roles as both a stabilizing agent and a particle size reducing agent in the aqueous solutions. The approach developed in this work enables further reductions in the particle sizes of noble-metal nanocatalysts. - Highlights: • Pulse-electrodeposition of Pt or Pt–Ru nanoparticles on carbon nanotubes • Carbon nanotubes used as a catalyst-supporting material • Citric acid used as reducing agent in the aqueous electrodeposition solutions • Electrochemical activity for methanol oxidation improved by a factor of 1.46 to 2.77.

Antimicrobial activity of a sodium hypochlorite/etidronic acid irrigant solution.

Science.gov (United States)

Arias-Moliz, Maria Teresa; Ordinola-Zapata, Ronald; Baca, Pilar; Ruiz-Linares, Matilde; Ferrer-Luque, Carmen María

2014-12-01

The aim of this study was to evaluate the antimicrobial activity of a 2.5% sodium hypochlorite (NaOCl)/9% etidronic acid (HEBP) irrigant solution on Enterococcus faecalis growing in biofilms and a dentinal tubule infection model. The antimicrobial activity of the solutions 2.5% NaOCl and 9% HEBP alone and associated was evaluated on E. faecalis biofilms grown in the Calgary biofilm model (minimum biofilm eradication concentration high-throughput device). For the dentinal tubule infection test, the percentage of dead cells in E. faecalis-infected dentinal tubules treated with the solutions for 10 minutes was measured using confocal laser scanning microscopy and the live/dead technique. Available chlorine and pH of the solutions were also measured. Distilled water was used as the control. Nonparametric tests were used to determine statistical differences. The highest viability was found in the distilled water group and the lowest in the NaOCl-treated dentin (P antimicrobial activity inside dentinal tubules, without statistical differences between the 2 (P chlorine within 60 minutes. HEBP did not interfere with the ability of NaOCl to kill E. faecalis grown in biofilms and inside dentinal tubules. Copyright © 2014 American Association of Endodontists. Published by Elsevier Inc. All rights reserved.

The extraction of trace amounts of gold from different aqueous mineral acid solutions by diphenyl-2-pyridylmethane dissolved in chloroform

International Nuclear Information System (INIS)

Iqbal, M.; Ejaz, M.; Chaudhri, S.A.; Zamiruddin

1978-01-01

Diphenyl-2-pyridylmethane, a high-molecular-weight substituted pyridine has been examined. Its behaviour is similar to that of amines in that it forms salts with mineral acids. The acid ionization constant (pKsub(BHsup(+)) is 4.4+-0.06 at 25 deg C. A study of the partition behaviour of trace amounts of gold between mineral acid solutions and 0.1 M diphenyl-2-pyridylmethane dissolved in chloroform indicates that the metal can be quantitatively extracted from dilute mineral acid solutions and also from concentrated hydrochloric acid media in a single extraction. Common anions have little effect on extraction in concentrations up to 1 M. Separation factors of a number of metal ions relative to gold are reported for three mineral acid systems. Gold has been estimated in some synthetic samples using a neutron-activation technique by prior extraction with 0.1 M solution of diphenyl-2-pyridylmethane dissolved in chloroform. Distribution of the test elements between aqueous and organic phase was followed radiometrically. The solutions (usually 1 cm 3 ) were shaken in stoppered vials for 5 minutes using a mechanical shaker. After separation of the layers, 500 μl of each phase were taken for radiochemical analysis. The standard deviation did not exceed 1%. (T.G.)

Degradation of 2,4,5-trichlorophenoxyacetic acid in aqueous solution by 60Co-γ irradiation

International Nuclear Information System (INIS)

Liu Yuanxia; Yu Yuan; Bao Huaying

2010-01-01

2,4,5-trichlorophenoxyacetic acid(2,4,5-T) is one kind of phenoxy-hydroxy-acid herbicides, also is one kind of Endocrine Disrupting Chemicals. The degradation of 2,4,5-T in aqueous solution by 60 Co-γ irradiation was investigated in the paper. The degradation effect of different influencing factors, such as absorbed dose and irradiation aura, was studied respectively. The degradation products were preliminarily analyzed by High Performance Liquid Chromatography, UV-Vis spectrophotometer and Ion Chromatography. The results showed that 2,4,5-T could be effectively degraded in aqueous solutions by 60 Co-γ irradiation. Meanwhile, the Chloride ion was detected in the solution, whose concentration increased with the growth of absorbed dose. It was found that although both e-aq and ·OH originated from water radiolysis could eliminate 2,4,5-T, the dechlorination effect and the degradation products were different. (authors)

Structure elucidation and quantification of impurities formed between 6-aminocaproic acid and the excipients citric acid and sorbitol in an oral solution using high-resolution mass spectrometry and nuclear magnetic resonance spectroscopy

DEFF Research Database (Denmark)

Schou-Pedersen, Anne Marie V; Cornett, Claus; Nyberg, Nils

2015-01-01

Concentrated solutions containing 6-aminocaproic acid and the excipients citric acid and sorbitol have been studied at temperatures of 50 °C, 60 °C, 70 °C and 80 °C as well as at 20 °C. It has previously been reported that the commonly employed citric acid is a reactive excipient, and it is there......Concentrated solutions containing 6-aminocaproic acid and the excipients citric acid and sorbitol have been studied at temperatures of 50 °C, 60 °C, 70 °C and 80 °C as well as at 20 °C. It has previously been reported that the commonly employed citric acid is a reactive excipient...... and cyclized 6-aminocaproic acid, i.e., caprolactam. No reaction products between d-sorbitol and 6-aminocaproic acid could be observed. 3-Hydroxy-3,4-dicarboxy-butanamide-N-hexanoic acid, dimer and caprolactam were also observed after storage at 20 °C for 3 months. The findings imply that an oral solution of 6...

Laboratory evaluation of limestone and lime neutralization of acidic uranium mill tailings solution. Progress report

International Nuclear Information System (INIS)

Opitz, B.E.; Dodson, M.E.; Serne, R.J.

1984-02-01

Experiments were conducted to evaluate a two-step neutralization scheme for treatment of acidic uranium mill tailings solutions. Tailings solutions from the Lucky Mc Mill and Exxon Highland Mill, both in Wyoming, were neutralized with limestone, CaCO 3 , to an intermediate pH of 4.0 or 5.0, followed by lime, Ca(OH) 2 , neutralization to pH 7.3. The combination limestone/lime treatment methods, CaCO 3 neutralization to pH 4 followed by neutralization with Ca(OH) 2 to pH 7.3 resulted in the highest quality effluent solution with respect to EPA's water quality guidelines. The combination method is the most cost-effective treatment procedure tested in our studies. Neutralization experiments to evaluate the optimum solution pH for contaminant removal were performed on the same two tailings solutions using only lime Ca(OH) 2 as the neutralizing agent. The data indicate solution neutralization above pH 7.3 does not significantly increase removal of pH dependent contaminants from solution. Column leaching experiments were performed on the neutralized sludge material (the precipitated solid material which forms as the acidic tailings solutions are neutralized to pH 4 or above). The sludges were contacted with laboratory prepared synthetic ground water until several effluent pore volumes were collected. Effluent solutions were analyzed for macro ions, trace metals and radionuclides in an effort to evaluate the long term effectiveness of attenuating contaminants in sludges formed during solution neutralization. Neutralized sludge leaching experiments indicate that Ca, Na, Mg, Se, Cl, and SO 4 are the only constituents which show solution concentrations significantly higher than the synthetic ground water in the early pore volumes of long-term leaching studies

Study on radiation-induced oxide-reduction of actinoid ions in acid solution

Energy Technology Data Exchange (ETDEWEB)

Ishigure, Kenkichi; Katsumura, Yosuke; Hiroishi, Daisuke [Tokyo Univ. (Japan). Faculty of Engineering; and others

1996-01-01

Many studies have been made on the application of actinoid ion, especially UO{sub 2}{sup 2+} to change atomic valance but the mechanism of photoreduction has not yet been solved. In this study, the mechanism of photoreduction of UO{sub 2}{sup 2+} in acid solution was investigated. As functions of alcohol and acid concentrations, {phi}(U{sup IV}) was determined and photoreduction of UO{sub 2}{sup 2+} was investigated as well as NpO{sub 2}{sup 2+}. As an increase of alcohol content (EtOH, MtOH, iso-PrOH), {phi}(U{sup IV}) increased to reach a plateau ({approx}0.6). In addition, {phi}(U{sup IV}) increased linearly with an increase of acid content and the value became smaller in the order, H{sub 3}PO{sub 4}, H{sub 2}SO{sub 4}, HClO{sub 4} solution. Comparing with these results of UO{sub 2}{sup 2+}, photoreduction of NpO{sub 2}{sup 2+} was investigated. Only NpO{sub 2}{sup +} was produced as the final products, but not Np{sup IV} and NP{sup III}. Alcohol dependency of NpO{sub 2}{sup 2+} photoreduction was similar to that of UO{sub 2}{sup 2+} system but the plateau level of {phi} (NpO{sub 2}{sup 2+}) was lower ({approx}0.15) than the latter. (M.N.)

Double thermal transitions of type I collagen in acidic solution.

Science.gov (United States)

Liu, Yan; Liu, Lingrong; Chen, Mingmao; Zhang, Qiqing

2013-01-01

Contributed equally to this work. To further understand the origin of the double thermal transitions of collagen in acidic solution induced by heating, the denaturation of acidic soluble collagen was investigated by micro-differential scanning calorimeter (micro-DSC), circular dichroism (CD), dynamic laser light scattering (DLLS), transmission electron microscopy (TEM), and two-dimensional (2D) synchronous fluorescence spectrum. Micro-DSC experiments revealed that the collagen exhibited double thermal transitions, which were located within 31-37 °C (minor thermal transition, T(s) ∼ 33 °C) and 37-55 °C (major thermal transition, T(m) ∼ 40 °C), respectively. The CD spectra suggested that the thermal denaturation of collagen resulted in transition from polyproline II type structure to unordered structure. The DLLS results showed that there were mainly two kinds of collagen fibrillar aggregates with different sizes in acidic solution and the larger fibrillar aggregates (T(p2) = 40 °C) had better heat resistance than the smaller one (T(p1) = 33 °C). TEM revealed that the depolymerization of collagen fibrils occurred and the periodic cross-striations of collagen gradually disappeared with increasing temperature. The 2D fluorescence correlation spectra were also applied to investigate the thermal responses of tyrosine and phenylalanine residues at the molecular level. Finally, we could draw the conclusion that (1) the minor thermal transition was mainly due to the defibrillation of the smaller collagen fibrillar aggregates and the unfolding of a little part of triple helices; (2) the major thermal transition primarily arose from the defibrillation of the larger collagen fibrillar aggregates and the complete denaturation of the majority part of triple helices.

Liquid Superlubricity of Polyethylene Glycol Aqueous Solution Achieved with Boric Acid Additive.

Science.gov (United States)

Ge, Xiangyu; Li, Jinjin; Zhang, Chenhui; Luo, Jianbin

2018-03-27

Boric acid is a weak acid and has been used as a lubrication additive because of its special structure. In this study, we report that boric acid could achieve a robust superlubricity (μ friction coefficient of approximately 0.004-0.006 could be achieved with boric acid under neutral conditions (pH of approximately 6.4), which is different from the acidic conditions leading to superlubricity. The influence of various factors, including boric acid concentration, sliding speed, applied load, PEG molecular weight, and the volume of lubricant on the superlubricity, were investigated. The results reveal that the PEG aqueous solution with the boric acid additive could achieve superlubricity under a wide range of conditions. The surface composition analysis shows that the synergy effect between boric acid and PEG provides sufficient H + ions to realize the running-in process. Moreover, a composite tribochemical film composed of silica and ammonia-containing compounds were formed on the ball surface, contributing to the superlubricity. The film thickness calculation shows that superlubricity was achieved in a mixed lubrication region, and therefore, the superlubricity state was dominated by both the composite tribochemical film formed via the tribochemical reaction on the contact surfaces and the hydrodynamic lubricating film between the contact surfaces. Such a liquid superlubricity achieved under neutral conditions is of importance for both scientific understanding and engineering applications.

Uranium removal from acidic aqueous solutions by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa

International Nuclear Information System (INIS)

Sarri, S.; Misaelides, P.; Papanikolaou, M.; Zamboulis, D.

2009-01-01

The sorption of uranium from acidic aqueous solutions (pH 4.5, C init = 10 to 1000 mg U/L) by Saccharomyces cerevisiae, Debaryomyces hansenii, Kluyveromyces marxianus and Candida colliculosa was investigated using a batch technique. The U-sorption onto Saccharomyces cerevisiae and Debaryomyces hansenii followed a Langmuir, while that onto Kluyveromyces marxianus and Candida colliculosa a Freundlich isotherm. The results demonstrated that all investigated biomasses could effectively remove uranium from acidic aqueous solutions. From all sorbents, Saccharomyces cerevisiae appeared to be the most effective with a maximum sorption capacity of 127.7 mg U/g dry biomass. (author)

Determination of free acid in U(VI)-Al(III) solution by Gran plot titration

International Nuclear Information System (INIS)

Suh, Moo Yul; Lee, Chang Heon; Sohn, Se Chul; Kim, Jung Suk; Kim, Won Ho; Eom, Tae Yoon

1999-01-01

The determination method of free acid in spent U-Al nuclear fuel solutions by Gran plot titration was described. Effect of U(VI) and Al(III) on the alkalimetric titration of nitric acid was investigation in oxalate complexing media as well as in noncomplexing media. Positive biases were observed in both titration media when the end-point was estimated by the Gran plot method. It was found that the cause of the bias was U(VI) in the oxalate complexing media, but Al(III) in the noncomplexing media. The relative error was less than 1% in the titration of 0.1 M HNO 3 at a U(VI):Al(III):H + mole ratio of up to 2:12:1 as long as the pH of the oxalate titration media was sustained to be below 5.0 at the beginning of titration. The method was successfully applied to the determination of nitric acid in a solution of HANARO reactor fuel with U:Al mole ratio of 1:6

Biosorption of Acid Yellow 17 from aqueous solution by non-living aerobic granular sludge

International Nuclear Information System (INIS)

Gao Jingfeng; Zhang Qian; Su Kai; Chen Ranni; Peng Yongzhen

2010-01-01

Batch biosorption experiments were carried out for the removal of Acid Yellow 17 from aqueous solution using non-living aerobic granular sludge as an effective biosorbent. The effects of solution pH value, biosorbent dosage, initial Acid Yellow 17 concentration, NaCl concentration and temperature on the biosorption were investigated. The experimental results indicate that this process was highly dependent on pH value and the pH value of 2.0 was favorable. The Temkin isotherm was more applicable for describing the biosorption equilibrium at the whole concentration range than the Freundlich and Langmuir isotherm. The results of kinetics study show that the pseudo-second-order model fitted to the experimental data well. Both intraparticle diffusion and boundary layer diffusion might affect the biosorption rate. Thermodynamic studies demonstrate that the biosorption process was spontaneous and exothermic. The FTIR analysis before and after Acid Yellow 17 binding indicated that functional groups such as amine, hydroxyl, carboxyl and either on the non-living aerobic granular sludge would be the active binding sites for the biosorption of the studied dye. These results show that non-living aerobic granular sludge could be effectively used as a low-cost and alternative biosorbent for the removal of Acid Yellow 17 dye from wastewater.

Analysis of tellurium-silicon alloys. Part 1. Determination of tellurium by the reduction from perchloric acid solution

International Nuclear Information System (INIS)

Teperek, J.

1977-01-01

When 100-150 mg of tellurium is dissolved in the solution containing 20 cm 3 72 wt.% of perchloric acid, the reduction of tellurium to elementary form is possible only after adding 60-100 milimoles of HCl. The reduction is performed by adding 1 cm 3 of saturated sodium pyrosulphite solution (Na 2 S 2 O 5 ) and 10 cm 3 of 10 wt.% hydrazine hydrochloride solution (N 2 H 4 .2HCl) to 80-90 cm 3 of cold solution of Te in HClO 4 -HCl mixture. The reduction is completed after 3-5 min. of boiling. When 150-200 mg sample of Te-Si alloy is dissolved in 20 cm 3 of hot 72% per chloric acid, the separation of components is reached. Tellurium can be determinated in filtrate by proposed procedure with high accuracy and precision. (author)

Fabrications of Polyaniline Films by Pulse Electrodeposition in Acidic Solutions with Different Anions and Their Thermoelectric Performances

Science.gov (United States)

Yang, Weifang; Xu, Han; Li, Yuanyuan; Wang, Wei

2017-08-01

Polymerization of aniline was prepared by the pulse potentiostatic method in H3PO4, HClO4 and H2SO4 acidic solutions. The morphologies and thermoelectric performances were analyzed by scanning electron microscopy, Seebeck coefficient ( S) and resistivity ( R) measurements. The results show that flake polyaniline (PANI) films can be obtained in H3PO4 and HClO4 acidic solutions, and porous PANI films with nanofiber-overlapped structures can be prepared in H2SO4 solution under the same pulse parameters. PANI films prepared in the three solutions are all p-type thermoelectric materials. PANI films polymerized in H2SO4 solution possess the highest S (30.2 μV K-1) and lowest R (1.6 × 10-3 Ω m) compared with those prepared in H3PO4 and HClO4 solutions, indicating that nanofiber-overlapped structures formed in H2SO4 solution contribute better thermoelectric performance. In addition, the effects of pulse parameters (anodic potential φ a, anodic pulse duration t a and cathodic pulse duration t c) on the surface morphologies and thermoelectric performances of PANI films were systematically investigated.

Acid-base buffering in organ preservation solutions as a function of temperature: new parameters for comparing buffer capacity and efficiency.

Science.gov (United States)

Baicu, Simona C; Taylor, Michael J

2002-08-01

Control of acidity and preventing intracellular acidosis are recognized as critical properties of an effective organ preservation solution. Buffer capacity and efficiency are therefore important for comparing the relative merits of preservation fluids for optimum hypothermic storage, but these parameters are not available for the variety of organ preservation solutions of interest in transplantation today. Moreover, buffer capacity is dependent upon both concentration and pH such that buffer capacity is not easily predicted for a complex solution containing multiple buffer species. Using standard electrometric methods to measure acid dissociation constants, this study was undertaken to determine the maximum and relative buffer capacities of a variety of new and commonly used hypothermic preservation solutions as a function of temperature. The reference data provided by these measurements show that comparative buffer capacity and efficiency vary widely between the commonly used solutions. Moreover, the fluids containing zwitterionic sulfonic acid buffers such as Hepes possess superior buffering for alpha-stat pH regulation in the region of physiological importance.

Thermodynamics of Dissolution for Crystalline Racemic Tartaric and Glutaric Acids and Isatin in KOH Aqueous Solutions at 298.15 K

Science.gov (United States)

Lytkin, A. I.; Chernikov, V. V.; Krutova, O. N.; Litvinenko, V. E.; Volkov, A. V.; Bychkova, S. A.; Skvortsov, I. A.

2018-01-01

Enthalpies of dissolution are found for crystalline racemic tartaric and glutaric acids and isatin in water and in potassium hydroxide solutions at 298.15 K via direct calorimetry. The protolytic equilibria in isatin aqueous solutions are studied at 298.15 K and ionic strengths of 0.5 (relative to potassium nitrate) by potentiometric means. Standard enthalpies of formation are calculated for racemic tartaric and glutaric acids, isatin, and the products of their dissociation in aqueous solutions.

Solution mining process

International Nuclear Information System (INIS)

Showalter, W.E.

1984-01-01

A solution mining process which may be used for uranium, thorium, vanadium, copper, nickel, molybdenum, rhenium, and selenium is claimed. During a first injection-and-production phase of between 6 months and 5 years, a leaching solution is injected through at least one well into the formation to solubilize the mineral values and form a pregnant liquor. This liquor is recovered through another well. The leaching solution contains sulfuric acid, nitric acid, hydrochloric acid, carbonic acid, an alkali metal carbonate, an alkali metal bicarbonate, ammonium carbonate or ammonium bicarbonate. Subsequently during a first production-only phase of between about 2 weeks and one year, injection of the leaching solution is suspended but pregnant liquor is still recovered. This stage is followed by a second injection-and-production phase of between 6 months and 5 years and a second production-only phase. The mineral values are separated from the pregnant liquor to form a barren liquor. The leaching agent is introduced into this liquor, and the solution is recycled. In a second claim for the solution mining of uranium, dilute carbonic acid is used as the leaching solution. The solution has a pH less than 7 and a bicarbonate ion concentration between about 380 ppm and 1000 ppm. The injection-and-production phase lasts between one and two years and the production only phase takes between one and four months. Carbon dioxide is introduced into the barren liquor to form a dilute carbonic acid solution and the solution is recycled

Potentiality of uranium biosorption from nitric acid solutions using shrimp shells.

Science.gov (United States)

Ahmed, S H; El Sheikh, E M; Morsy, A M A

2014-08-01

Biosorption has gained important credibility during recent years because of its good performance and low cost. This work is concerned with studying the potentiality of the chitin component of the shrimp shells for uranium biosorption from nitric acid liquid solutions. The structural characteristics of the working chitin have been determined via Fourier Transform Infrared Spectroscopy (FTIR). The surface morphology was examined using Scanning Electron Microscopy (SEM). The adsorption capacity of biomass was investigated experimentally. The influence of contact time, pH, metal ion concentration, solution volume to mass ratio and temperature were evaluated and the results were fitted using adsorption isotherm models. The kinetic of uranium biosorption was also investigated as well as biosorption thermodynamic. Copyright © 2014 Elsevier Ltd. All rights reserved.

The anodizing behavior of aluminum in malonic acid solution and morphology of the anodic films

Science.gov (United States)

Ren, Jianjun; Zuo, Yu

2012-11-01

The anodizing behavior of aluminum in malonic acid solution and morphology of the anodic films were studied. The voltage-time response for galvanostatic anodization of aluminum in malonic acid solution exhibits a conventional three-stage feature but the formation voltage is much higher. With the increase of electrolyte concentration, the electrolyte viscosity increases simultaneously and the high viscosity decreases the film growth rate. With the concentration increase of the malonic acid electrolyte, the critical current density that initiates local "burning" on the sample surface decreases. For malonic acid anodization, the field-assisted dissolution on the oxide surface is relatively weak and the nucleation of pores is more difficult, which results in greater barrier layer thickness and larger cell dimension. The embryo of the porous structure of anodic film has been created within the linear region of the first transient stage, and the definite porous structure has been established before the end of the first transient stage. The self-ordering behavior of the porous film is influenced by the electrolyte concentration, film thickness and the applied current density. Great current density not only improves the cell arrangement order but also brings about larger cell dimension.

Carbamazepine-Fumaric Acid Co-Crystal Screening Using Solution Based Method

Directory of Open Access Journals (Sweden)

Abd Rahim Syarifah

2016-01-01

Full Text Available Co-crystals is a multi-component system which connected by non-covalent interactions, present physically as a solid form under ambient conditions. Nowadays, co-crystal has becoming as an alternative approach to improve the bioavailability of poor water soluble drugs especially for a weakly ionisable groups or neutral compounds. In this study the co-crystal screening was carried out for carbamazepine (CBZ and fumaric acid (FUM co-crystal former (CCF using non-stoichiometric method (addition of CBZ to CCF saturated solution and stoichiometric method (evaporation of 1:1 molar ratio of CBZ to CCF in acetonitrile, ethyl acetate, propanol, ethanol and formic acid solvent systems. The crystals produced from the screening were characterized using Powder X-ray Diffraction (PXRD, Differential Scanning Calorimetry (DSC and Fourier Transform Infrared (FT-IR. The PXRD analysis had confirmed that the co-crystal was successfully formed in both methods for all of the solvent system studied with an exception to formic acid in the stoichiometric method where no crystal was found precipitate. The findings from this study revealed that Form A and Form B of CBZ-FUM co-crystal had been successfully formed from different solvent systems.

Resistometric studies of anodic dissolution and passivation of chromium in weakly acid solutions

International Nuclear Information System (INIS)

Shlepakov, M.N.; Sukhotin, A.M.

1984-01-01

The method of calculating the rate of Cr anodic solution according to the change of electric resistance of chromium anodes under the effect of potentiostatic polarization, is applied. The maximum corresponding to ranges of active-passive transition is absent in weakly acid solutions with pH>3. The range of existence of active-passive transition is expanded to pH approximately 5.2. The existence of a dissolving section in Cr in the chemical mechanism is proved. Cr passivation mechanism with the formation of passivating oxide of a complex composition is suggested

Field effects in graphene in an interface contact with aqueous solutions of acetic acid and potassium hydroxide

Science.gov (United States)

Butko, A. V.; Butko, V. Yu.; Lebedev, S. P.; Lebedev, A. A.; Kumzerov, Yu. A.

2017-10-01

For the creation of new promising chemical sensors, it is very important to study the influence of the interface between graphene and aqueous solutions of acids and alkalis on the transistor characteristics of graphene. Transistor structures on the basis of graphene grown by thermal decomposition of silicon carbide were created and studied. For the interface of graphene with aqueous solutions of acetic acid and potassium hydroxide in the transistor geometry, with a variation in the gate-to-source voltage, the field effect corresponding to the hole type of charge carriers in graphene was observed. It is established that an increase in the concentration of molecular ions in these solutions leads to an increase in the dependence of the resistance of the transistor on the gate voltage.

Spectral characterization of the fluorescent components present in humic substances, fulvic acid and humic acid mixed with pure benzo(a)pyrene solution

Science.gov (United States)

El Fallah, Rawa; Rouillon, Régis; Vouvé, Florence

2018-06-01

The fate of benzo(a)pyrene (BaP), a ubiquitous contaminant reported to be persistent in the environment, is largely controlled by its interactions with the soil organic matter. In the present study, the spectral characteristics of fluorophores present in the physical fractions of the soil organic matter were investigated in the presence of pure BaP solution. After extraction of humic substances (HSs), and their fractionation into fluvic acid (FA) and humic acid (HA), two fluorescent compounds (C1 and C2) were identified and characterized in each physical soil fraction, by means of fluorescence excitation-emission matrices (FEEMs) and Parallel Factor Analysis (PARAFAC). Then, to each type of fraction having similar DOC content, was added an increasing volume of pure BaP solution in attempt to assess the behavior of BaP with the fluorophores present in each one. The application of FEEMs-PARAFAC method validated a three-component model that consisted of the two resulted fluorophores from HSs, FA and HA (C1 and C2) and a BaP-like fluorophore (C3). Spectral modifications were noted for components C2HSs (C2 in humic substances fraction) (λex/λem: 420/490-520 nm), C2FA (C2 in fulvic acid fraction) (λex/λem: 400/487(517) nm) and C1HA (C1 in humic acid fraction) (λex/λem: 350/452(520) nm). We explored the impact of increasing the volume of the added pure BaP solution on the scores of the fluorophores present in the soil fractions. It was found that the scores of C2HSs, C2FA, and C1HA increased when the volume of the added pure BaP solution increased. Superposition of the excitation spectra of these fluorophores with the emission spectrum of BaP showed significant overlaps that might explain the observed interactions between BaP and the fluorescent compounds present in SOM physical fractions.

Electrochemical formation of hydroxide for enhancing carbon dioxide and acid gas uptake by a solution

Science.gov (United States)

Rau, Gregory Hudson

2014-07-01

A system for forming metal hydroxide from a metal carbonate utilizes a water electrolysis cell having an acid-producing anode and a hydroxyl-producing cathode immersed in a water solution of sufficient ionic content to allow an electric current to pass between the hydroxyl-producing cathode and the acid-producing anode. A metal carbonate is placed in close proximity to the acid-producing anode. A direct current electrical voltage is provided across the acid-producing anode and the hydroxyl-producing cathode sufficient to generate acid at the acid-producing anode and hydroxyl ions at the hydroxyl-producing cathode. The acid dissolves at least part of the metal carbonate into metal and carbonate ions allowing the metal ions to travel toward the hydroxyl-producing cathode and to combine with the hydroxyl ions to form the metal hydroxide. The carbonate ions travel toward the acid-producing anode and form carbonic acid and/or water and carbon dioxide.

Protection of copper surface with phytic acid against corrosion in chloride solution.

Science.gov (United States)

Peca, Dunja; Pihlar, Boris; Ingrid, Milošev

2014-01-01

Phytic acid (inositol hexaphosphate) was tested as a corrosion inhibitor for copper in 3% sodium chloride. Phytic acid is a natural compound derived from plants, it is not toxic and can be considered as a green inhibitor. Electrochemical methods of linear polarization and potentiodynamic polarization were used to study the electrochemical behaviour and evaluate the inhibition effectiveness. To obtain the optimal corrosion protection the following experimental conditions were investigated: effect of surface pre-treatment (abrasion and three procedures of surface roughening), pre-formation of the layer of phytic acid, time of immersion and concentration of phytic acid. To evaluate the surface pre-treatment procedures the surface roughness and contact angle were measured. Optimal conditions for formation of phytic layer were selected resulting in the inhibition effectiveness of nearly 80%. Morphology and composition of the layer were further studied by scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray photoelectron spectroscopy. The layer of phytic acid with thickness in the nanometer range homogeneously covers the copper surface. The obtained results show that this natural compound can be used as a mildly effective corrosion inhibitor for copper in chloride solution.

Effect of magnesium acetate on the volumetric and transport behavior of some amino acids in aqueous solutions at 298.15K

International Nuclear Information System (INIS)

Banipal, Tarlok S.; Kaur, Damanjit; Banipal, Parampaul K.

2006-01-01

Densities, ρ, and viscosities, η, of glycine, dl-α-alanine, dl-α-amino-n-butyric acid, l-leucine and l-phenylalanine in 0.5, 1.0, 1.5 and 2.0 m B of aqueous magnesium acetate solutions at 298.15K have been measured as a function of concentration of amino acids using vibrating tube-digital densimeter and Ubbelohde capillary type viscometer, respectively. The apparent molar volumes, V φ , and relative viscosities, η r , of amino acids have been derived. The partial molar volume at infinite dilution, V 2 0 , and viscosity B-coefficient obtained from these data have been used to calculate the corresponding transfer parameters, Δ t V 0 , and Δ t B, for the studied amino acids from water to aqueous magnesium acetate solutions. The activation free energies, Δμ 2 0 >, for the viscous flow of solutions have been obtained by application of the transition-state theory to the viscosity B-coefficient data. The interaction coefficients and hydration number, n H , of amino acids in aqueous solutions have also been calculated to see the effect of magnesium acetate on the hydration of amino acids. The contribution of the zwitterionic end groups (NH 3 + , COO - ) and (CH 2 ) group of the amino acids to V 2 0 , viscosity B-coefficient and Δμ 2 0 > have been calculated. These results have been rationalized in terms of the hydration of hydrophilic and hydrophobic parts of amino acids

Efficiency of application of electroactivated aqueous solution in the production of bread low acidity

Directory of Open Access Journals (Sweden)

E. I. Ponomareva

2016-01-01

Full Text Available In diseases of the gastrointestinal tract, it is recommended to refrain from food oxidation. Therefore, the inclusion in the diet of bakery products with low acidity is important in the diet for such patients. One way to reduce the acidity of bread is the use of electric aqueous solution (EAS. Studied the effect of EAS with different values of рН (7.42; 9.34; 11.12 on the properties of dough and quality of bread from wheat flour first grade. The dough is kneaded straight dough method. In the fermentation process investigated the change in effective viscosity and titratable acidity. After fermentation the dough is molded, the test workpiece is subjected to proofing and baking. In ready from deliah determined the acidity, moisture content, porosity and specific volume. It is established that all samples of the test there was a decrease of effective viscosity in the fermentation process due to the occurrence of physico-chemical processes. The maximum value of effective viscosity is characterized by the semi-finished product, obtained using EAS рН of which 11.12 (3474 PA⋅s. It is revealed that the least value of ultimate рН (1.7 deg also had a sample on EAS with a рН = 11.12. The use of catholyte fraction of HRES with the given value of рН allowed to decrease the acidity in the finished product (45.5% compared with the control in the pilot study value was 1.2 degrees, while in the control to 2.2. The research concluded that the use of electroactivated aqueous solution suitable for the production of bakery products of low acidity.

Steric structure and thermodynamic aspects of Dy3+ complexes with aminobenzoic acids in aqueous solutions

International Nuclear Information System (INIS)

Kondrashina, Yu.G.; Mustafina, A.R.; Vul'fson, S.G.

1994-01-01

Stability and structure of dysprosium(3) aminobenzoate complexes with molar ratios Dy:L 1:1 and 1:2 (HL-aminobenzoic acid) in aqueous solutions are determined on the basis of pH-metric and paramagnetic birefringence data. The increase of conjugation effect in the series of benzoic, meta- ortho-, and para-aminobenzoic acid results in the increase of stability of 1:1 and 1:2 complexes. Features of the structure and coordination of ligands in dysprosium complexes with meta-, ortho-, and para-aminobenzoic acid are considered. 11 refs.; 4 figs.; 2 tabs

Estimation of free acid content in lanthanide salt solution used for pH-potentiometric determination of their stability constants with organic ligands

International Nuclear Information System (INIS)

Zheltvaj, I.I.; Tishchenko, M.A.

1985-01-01

To improve the pH-potentiometric method for determining complex stability constants the possibility of alkalimetric titration of a free acid in the lanthanide perchlorate solution after binding metal ions by disodium salt of ethylene-diamine-tetraacetic acid is studied. The stability constants were determined from the difference between the total acid content after complexon addition and doubled metal cation content in the solution which has been preliminarily determined by the complexonometric method. It is shown that the alkaline (NaOH) equivalent quantities spent for free acid titration either in the absence or presence of the complexon is different. With increase of free acid content in the solution the difference in determinations with complexon and without it is somewhat reduced. Thus, the use of complexon contributes to a higher accuracy in determining the free acid, and in the first place in case of minor contents

Extraction of antimony from nitric acid solutions using tributyl phosphate. II. Tributyl phosphate-antimony(V)-nitric acid system

International Nuclear Information System (INIS)

Lakaev, V.S.; Smelov, V.S.

1989-01-01

The extraction of pentavalent antimony from nitric acid solutions using tributyl phosphate has been investigated. A possible mechanism for the extraction of antimony(V) has been determined and the (pre)concentration constant for the process has been calculated. The composition of the extracted antimony(V) complex has been deduced. A negative effect of temperature on the distribution coefficient for antimony(V) has also been demonstrated

White Paper on Potential Hazards Associated with Contaminated Cheesecloth Exposed to Nitric Acid Solutions

Energy Technology Data Exchange (ETDEWEB)

Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-20

This white paper addresses the potential hazards associated with waste cheesecloth that has been exposed to nitric acid solutions. This issue was highlighted by the cleanup of a 100 ml leak of aqueous nitric acid solution containing Heat Source (HS) plutonium on 21 June 2016. Nitration of cellulosic material is a well-understood process due to industrial/military applications of the resulting material. Within the Department of Energy complex, nitric acids have been used extensively, as have cellulosic wipes. If cellulosic materials are nitrated, the cellulosic material can become ignitable and in extreme cases, reactive. We have chemistry knowledge and operating experience to support the conclusion that all current wastes are safe and compliant. There are technical questions worthy of further experimental evaluation. An extent of condition evaluation has been conducted back to 2004. During this time period there have been interruptions in the authorization to use cellulosic wipes in PF-4. Limited use has been authorized since 2007 (for purposes other than spill cleanup), so our extent of condition includes the entire current span of use. Our evaluation shows that there is no indication that process spills involving high molarity nitric acid were cleaned up with cheesecloth since 2007. The materials generated in the 21 June leak will be managed in a safe manner compliant with all applicable requirements.

Adsorption and purification of radiogallium in hydrochloric acid and metal chloride solutions by non-ionic resin of macro-reticular type

International Nuclear Information System (INIS)

Imai, Kiyoko; Watari, Kazuo; Ohno, Shigeru; Ohmiya, Toshinobu; Kuroda, Emi; Izawa, Masami.

1986-01-01

Adsorption behavior of radiogallium ( 67 Ga, 68 Ga) on non-ionic MR resin (XAD-7) from hydrochloric acid, lithium chloride and other metal chloride solutions, and purification of 68 Ga by this resin were studied. Radiogallium was adsorbed on XAD-7 rapidly and quantitatively from the solution of higher chloride concentration than 6M. The adsorption behavior is similar to that obtained with 59 Fe and 195 Au previously. Based on adsorption data, elimination of trace amount of 68 Ge commonly contained in 68 Ga milked from a 68 Ge/ 68 Ga generator was tried. When 68 Ga-6M hydrochloric acid solution containing 68 Ge was passed through a XAD-7 column, all the activity was transferred on the column. After eliminating 68 Ge fraction with 3M hydrochloric acid, 68 Ga was obtained in high purity by eluting with 0.1M hydrochloric acid. (author)

Dissolution of oxalate precipitate and destruction of oxalate ion by hydrogen peroxide in nitric acid solution

International Nuclear Information System (INIS)

Kim, Eung-Ho; Chung, Dong-Yong; Park, Jin-Ho; Yoo, Jae-Hyung

2000-01-01

This study aims at developing an oxalate precipitation process, which is applicable to a partitioning of long-lived radionuclides from the high-level radioactive liquid waste. In order to achieve this, a study for decomposition-reaction of oxalic acid by hydrogen peroxide was first carried out. The decomposition rates of H 2 O 2 and oxalic acid increased with an increase of nitric acid concentration, and especially those decomposition rates steeply increased at more than 2 M HNO 3 . Based on this result, the decomposition kinetics of H 2 O 2 and oxalic acid were suggested in this work. Then, the dissolution of oxalate precipitate and the destruction of oxalate ion in the solution were examined. Oxalate precipitates were prepared by adding oxalic acid into a simulated radioactive waste containing 8 metallic elements. The precipitates obtained thereby were dissolved in various nitric acid concentrations and reacted with H 2 O 2 at 90degC. When the oxalates were completely dissolved, most of the oxalates were decomposed by adding H 2 O 2 , but in a slurry state the decomposition yield of the oxalate decreased with an increase of the slurry density in the solution. Such phenomenon was considered to be due to a catalytic decomposition of H 2 O 2 on a solid surface of oxalate and the decomposition mechanism was explained by a charge transfer from a surface of oxalate solid to H 2 O 2 , producing OH radicals which can destruct H 2 O 2 explosively. Accordingly, the experimental condition for the decomposition of the oxalate precipitates was found to be most favorable at 3 M HNO 3 under the initial concentrations of 0.2 M oxalate and 1 M H 2 O 2 . At 3M HNO 3 , oxalate precipitates could be safely and completely dissolved, and almost decomposed. Additionally, it was observed that the presence of ferric ion in the solution largely affects the decomposition rate of H 2 O 2 . This could be explained by a chain reaction of hydrogen peroxide with ferric ion in the solution

Regularities in the association of polymethacrylic acid with benzethonium chloride in aqueous solutions

Science.gov (United States)

Tugay, A. V.; Zakordonskiy, V. P.

2006-06-01

The association of cationogenic benzethonium chloride with polymethacrylic acid in aqueous solutions was studied by nephelometry, conductometry, tensiometry, viscometry, and pH-metry. The critical concentrations of aggregation and polymer saturation with the surface-active substance were determined. A model describing processes in such systems step by step was suggested.

Kinetics of reactions of aquacobalamin with aspartic and glutamic acids and their amides in water solutions

Science.gov (United States)

Bui, T. T. T.; Sal'nikov, D. S.; Dereven'kov, I. A.; Makarov, S. V.

2017-04-01

The kinetics of aquacobalamin reaction with aspartic and glutamic acids, and with their amides in water solutions, is studied via spectrophotometry. The kinetic and activation parameters of the process are determined. It is shown that the reaction product is cobalamin-amino acid complex. The data are compared to results on the reaction between aquacobalamin and primary amines.

The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions

International Nuclear Information System (INIS)

Liu Yang; Sun Changbin; Xu Jin; Li Youzhi

2009-01-01

Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO 4 .5H 2 O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 deg. C to 40 deg. C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca 2+ from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S=O) of

The use of raw and acid-pretreated bivalve mollusk shells to remove metals from aqueous solutions.

Science.gov (United States)

Liu, Yang; Sun, Changbin; Xu, Jin; Li, Youzhi

2009-08-30

Heavy metal removal from industrial wastewater is not only to protect living organisms in the environment but also to conserve resources such as metals and water by enabling their reuse. To overcome the disadvantage of high cost and secondary pollution by the conventional physico-chemical treatment techniques, environmentally benign and low-cost adsorbents are in demand. In this study, the use of raw and acid-pretreated bivalve mollusk shells (BMSs) to remove metals from aqueous solutions with single or mixed metal was evaluated at different BMSs doses, pH and temperatures in batch shaking experiments in laboratory conditions. When the BMSs were used to treat CuSO(4)x5H(2)O solution, the copper sorption capacities of the raw and acid-pretreated BMSs were approximately 38.93 mg/g and 138.95 mg/g, respectively. The copper removal efficiency (CRE) of the raw BMSs became greatly enhanced with increasing initial pH, reaching 99.51% at the initial pH 5. Conversely, the CRE of the acid-pretreated BMSs was maintained at 99.48-99.52% throughout the pH range of 1-5. Furthermore, the CRE values of the raw and acid-pretreated BMSs were not greatly changed when the temperature was varied from 15 degrees C to 40 degrees C. In addition, the CRE value of the raw BMSs was maintained for 12 cycles of sorption-desorption with a CRE of 98.4% being observed in the final cycle. Finally, when the BMSs were used to treat electroplating wastewater, the removal efficiencies (REs) of the raw BMSs were 99.97%, 98.99% and 87% for Fe, Zn and Cu, respectively, whereas the REs of the acid-pretreated BMSs were 99.98%, 99.43% and 92.13%, respectively. Ion exchange experiments revealed that one of mechanisms for metal sorption by the BMSs from aqueous solution is related to ion exchange, especially between the metal ions in the treated solution and Ca(2+) from BMSs. Infrared absorbance spectra analysis indicated that the acid pretreatment led to occurrence of the groups (i.e. -OH, -NH, C=O and S

Investigation into sorption of uranium fron its high-concentrated nitric acid solutions on resin AMP

International Nuclear Information System (INIS)

Savel'eva, V.I.; Sudarikov, B.N.; Kireeva, G.N.; Ryzhkova, V.N.; Kandaryuk, V.V.

1976-01-01

Sorption of uranium has been studied on strongly basic anion-exchange resin from nitric acid solutions with concentration in metal 10-150 g/l in presence of sodium, calcium, and aluminium nitrates. Sorption of uranium from solutions has been performed by the static method with the aid of contacting the initial solution with airdry resin for 4 hours, resin to solution ratio being 1:12.5. It has been established that sorption of uranium increases with a rise in concentration of salting out agents in the following order: Al(NO 3 ) 3 > Ca(NO 3 ) 2 > Na(NO 3 ). It has been shown spectrophotometricatly that in solutions of nitrates and HNO 3 with a concentration 3 exceeds 6 mol/l

A method for the determination of free nitric acid in aqueous plutonium nitrate solutions - potassium fluoride method

International Nuclear Information System (INIS)

Mair, M.A.

1988-06-01

Plutonium IV and VI, and certain other hydrolysable metals which may be present, are converted to non-interfering species by the addition of the sample to potassium fluoride solution. The free acid is then titrated with standard sodium hydroxide solution using phenolphthalein as an indicator. (author)

Interaction of Atmospheric-Pressure Air Microplasmas with Amino Acids as Fundamental Processes in Aqueous Solution.

Directory of Open Access Journals (Sweden)

Renwu Zhou

Full Text Available Plasma medicine is a relatively new field that investigates potential applications of cold atmospheric-pressure plasmas in bioengineering, such as for bacterial inactivation and degradation of organic molecules in water. In order to enunciate mechanisms of bacterial inactivation at molecular or atomic levels, we investigated the interaction of atmospheric-pressure air microplasmas with amino acids in aqueous solution by using high-resolution mass spectrometry (HRMS. Results show that the oxidation effect of plasma-induced species on the side chains of the amino acids can be categorized into four types, namely hydroxylation, nitration, dehydrogenation and dimerization. In addition, relative activities of amino acids resulting from plasma treatment come in descending order as follows: sulfur-containing carbon-chain amino acids > aromatic amino acids > five-membered ring amino acids > basic carbon-chain amino acids. Since amino acids are building blocks of proteins vital to the growth and reproduction of bacteria, these results provide an insight into the mechanism of bacterial inactivation by plasma.

Comparison of 30% salicylic acid with jessner's solution for superficial chemical peeling in epidermal melasma

International Nuclear Information System (INIS)

Ejaz, A.; Raza, N.; Iftikhar, N.; Muzzafar, F.

2008-01-01

To compare the efficacy and safety of Jessner's solution with 30% salicylic acid as superficial chemical peeling agents in treating epidermal melasma in Asian skin. Sixty consenting patients with epidermal melasma were randomly divided into two groups. Group A was treated with Jessner's solution and Group B with 30% salicylic acid. Baseline Melasma Area Severity Index (MASI) score was noted and peeling started at 2-weekly intervals. Sunscreen in morning and moisturizer at night were prescribed in all patients. MASI score and adverse effects were recorded biweekly. Treatment was stopped at 12 weeks and patients were followed-up at 4 weekly intervals for further 12 weeks. Final MASI score and adverse effects were noted at the end of follow-up period. Mean MASI scores were compared using paired sample t-test and one-way ANOVA. Difference in baseline, treatment end and follow-up end MASI scores was not statistically significant between the two groups (p=0.54, 0.26, and 0.55 respectively). On the other hand, within group analysis of difference between pre and posttreatment MASI score was highly significant in both groups (p < 0.0001). Adverse effects were mild and comparable in both groups. Jessner's solution and 30% salicylic acid are equally effective and safe peeling agents for use in epidermal melasma in Asian skin. (author)

Exceptionally crystalline and conducting acid doped polyaniline films by level surface assisted solution casting approach

Energy Technology Data Exchange (ETDEWEB)

Puthirath, Anand B.; Varma, Sreekanth J.; Jayalekshmi, S., E-mail: jayalekshmi@cusat.ac.in [Division for Research in Advanced Materials, Department of Physics, Cochin University of Science and Technology, Cochin, Kerala 682022 (India); Methattel Raman, Shijeesh [Nanophotonic and Optoelectronic Devices Laboratory, Department of Physics, Cochin University of Science and Technology, Cochin, Kerala 682022 (India)

2016-04-18

Emeraldine salt form of polyaniline (PANI) was synthesized by chemical oxidative polymerisation method using ammonium persulfate as oxidant. Resultant emeraldine salt form of PANI was dedoped using ammonia solution and then re-doped with camphor sulphonic acid (CSA), naphthaline sulphonic acid (NSA), hydrochloric acid (HCl), and m-cresol. Thin films of these doped PANI samples were deposited on glass substrates using solution casting method with m-cresol as solvent. A level surface was employed to get homogeneous thin films of uniform thickness. Detailed X-ray diffraction studies have shown that the films are exceptionally crystalline. The crystalline peaks observed in the XRD spectra can be indexed to simple monoclinic structure. FTIR and Raman spectroscopy studies provide convincing explanation for the exceptional crystallinity observed in these polymer films. FESEM and AFM images give better details of surface morphology of doped PANI films. The DC electrical conductivity of the samples was measured using four point probe technique. It is seen that the samples also exhibit quite high DC electrical conductivity, about 287 S/cm for CSA doped PANI, 67 S/cm for NSA doped PANI 65 S/cm for HCl doped PANI, and just below 1 S/cm for m-cresol doped PANI. Effect of using the level surface for solution casting is studied and correlated with the observed crystallinity.

A study on the alkalimetric titration with gran plot in noncomplexing media for the determination of free acid in spent fuel solutions

International Nuclear Information System (INIS)

Suh, Moo Yul; Lee, Chang Heon; Sohn, Se Chul; Kim, Jung Suk; Kim, Won Ho; Eom, Tae Yoon

1999-01-01

Based on the study of hydrolysis behaviour of U(VI) ion and major fission product metal ions such as Cs(I), Ce(III), Nd(III), Mo(VI), Ru(II), and Zr(VI) in the titration media, the performance of noncomplexing-alkalimetric titration method for the determination of free acid in the presence of these metal ions was investigated and its results were compared to those from the complexing methods. The free acidities could be determined as low as 0.05 meq in uranium solutions in which the molar ratio of U(VI)/H + was less than 5, when the end-point of titration was estimated by Gran plot. The biases in the determinations were less than ±1% and about +3% respectively for 0.4 meq and 0.05 meq of free acid at the U(VI)/H + molar ratio of up to 5. Applicability of this method to the determination of free acid in spent fuel solutions was confirmed by the analysis of nitric acid content in simulated spent fuel solutions and in a real spent fuel solution

The extraction of vanadium (IV) from hydrochloric acid solutions by tricaprylmethylammonium chloride and trioctylamine

International Nuclear Information System (INIS)

Nakamura, Takato; Sato, Taichi

1980-01-01

The extraction of vanadium (IV) from hydrochloric acid solutions by tricaprylmethylammonium chloride (R 3 RNCl, Aliquat-336) and trioctylamine (R 3 N, TOA) in benzene has been investigated under various conditions. In addition, the extraction behaviour of vanadium into the organic phase has been examined by spectrophotometry and electron spin resonance (ESR) spectroscopy. From the distribution data, it is concluded that the extractions of vanadium (IV) from hydrochloric acid solutions by Aliquat-336 and TOA are expressed as VOCl 3 - (aq) + R 3 R'NCl(org) reversible R 3 R'NVOCl 3 (org) + Cl - (aq) and VOCl 2 (aq) + R 3 NHCl(org) reversible R 3 NHVOCl 3 (org) The electronic spectral and ESR results suggest that the complexes, R 3 R'NVOCl 3 and R 3 NH.VOCl 3 , formed in the organic phase are not always stable, but easily hydrolized or oxidized. (author)

Color removal from acid and reactive dye solutions by electrocoagulation and electrocoagulation/adsorption processes.

Science.gov (United States)

Bellebia, S; Kacha, S; Bouberka, Z; Bouyakoub, A Z; Derriche, Z

2009-04-01

In this study, electrocoagulation of Marine Blue Erionyl MR (acid dye) and electrocoagulation followed by adsorption of Brilliant Blue Levafix E-BRA (reactive dye) from aqueous solutions were investigated, using aluminum electrodes and granular activated carbon (GAC). In the electrocoagulation and adsorption of dyestuff solutions, the effects of current density, loading charge, pH, conductivity, stirring velocity, contact time, and GAC concentration were examined. The optimum conditions for the electrocoagulation process were identified as loading charges 7.46 and 1.49 F/m3, for a maximum abatement of 200 mg/L reactive and acid dye, respectively. The residual reactive dye concentration was completely removed with 700 mg/L GAC. The results of this investigation provide important data for the development of a combined process to remove significant concentrations of recalcitrant dyes from water, using moderate activated carbon energy and aluminum consumption, and thereby lowering the cost of treatment.

Radiation chemistry of amino acids and peptides in aqueous solutions

International Nuclear Information System (INIS)

Simic, M.G.

1978-01-01

Radiation chemistry relevant to radiation preservation of high protein foods is reviewed. Some conclusions concerning the chemistry of irradiated amino acids, peptides, and proteins have been derived from product analysis of γ-irradiated solutions while the main mechanistic considerations result from the chemistry and kinetics of free radical intermediates observed by pulse radiolysis. The precursors of chemistry in not too concentrated solutions ( - , OH, and H. Their reactivity with molecules and their preference for characteristic groups within the molecule are discussed. The reviewed reactions of the model systems are accountable for a variety of radiolytic products found in irradiated foods. From detailed understanding of radiation chemistry in aqueous and frozen systems formation of many classes of compounds can be predicted or entirely eliminated in order to corroborate and extend the conclusions reached from the animal feeding experiments concerning the formation of toxic, mutagenic, and carcinogenic compounds and/or reduction of the nutritional value of foods

The investigation of antimony extraction with tributyl phosphate from nitric acid solutions

International Nuclear Information System (INIS)

Lakaev, V.S.; Smelov, V.S.

1988-01-01

Experimental data on trivalent antimony extraction with tributyl phosphate from nitric acid solutions containing (3.2-4.3)x10 -6 mol/l of antimony-125 isotope are presented. Possible mechanism of antimony (3) extraction is determined and the concentration constant for this process is calculated. Effect of temperature on the extraction of trivalent antimony is estimated. The values of enthalpy, free enthalpy and entropy are determined

Straining electrode behavior and corrosion resistance of nickel base alloys in high temperature acidic solution

International Nuclear Information System (INIS)

Yamanaka, Kazuo

1992-01-01

Repassivation behavior and IGA resistance of nickel base alloys containing 0∼30 wt% chromium was investigated in high temperature acid sulfate solution. (1) The repassivation rate was increased with increasing chromium content. And so the amounts of charge caused by the metal dissolution were decreased with increasing chromium content. (2) Mill-annealed Alloy 600 suffered IGA at low pH environment below about 3.5 at the fixed potentials above the corrosion potential in 10%Na 2 SO 4 +H 2 SO 4 solution at 598K. On the other hand, thermally-treated Alloy 690 was hard to occur IGA at low pH environments which mill-annealed Alloy 600 occurred IGA. (3) It was considered that the reason, why nickel base alloys containing high chromium content such as Alloy 690 (60%Ni-30%Cr-10%Fe) had high IGA/SCC resistance in high temperature acidic solution containing sulfate ion, is due to both the promotion of the repassivation and the suppression of the film dissolution by the formation of the dense chromium oxide film

Anionic Surfactant as a Corrosion Inhibitor for Synthesized Ferrous Alloy in Acidic Solution

Directory of Open Access Journals (Sweden)

Farida Kellou-Kerkouche

2013-01-01

Full Text Available The effect of temperature on the corrosion behaviour of a synthesized iron-based alloy in 1 N sulphuric acid solution has been examined by means of three electrochemical techniques. Thereafter, we studied the influence of an anionic surfactant (sodium dodecyl benzene sulfonate at various concentrations on the electrochemical behaviour of the ferrous alloy. The obtained results show that the temperature increase reduced the performance of the used alloy, in the acidic environment. Otherwise, the surfactant inhibits the alloy dissolution in the sulphuric acid, through its adsorption on the metal surface without modifying the mechanism of corrosion process. We also noticed that the highest inhibition effect is obtained at a concentration above its critical micelle concentration (CMC. Langmuir adsorption isotherm fits well with the experimental data.

Study of the properties of dialkyl thiophosphoric acids. Application to the extraction of U, in phosphoric and nitric solutions

International Nuclear Information System (INIS)

Benjelloun, N.

1983-09-01

A study is made of complex formation and liquid-liquid extraction of uranium (VI) by dialkyl-thiophosphoric acids of formula (RO) 2 POSH and by the synergic mixtures: dialkylthiophosphoric acids-phosphine oxides. The aqueous phases studied consist of concentrated phosphoric acid solutions and nitric acid solutions. Several methods, including distribution coefficient measurements, U.V., visible and infrared absorption spectrophotometries and magnetic resonance, were used to study the extraction mechanisms and the structures of species formed in the organic phase. The influence of different parameters (partition of extraction agent, dimerisation, acid ligand-phosphine oxide association, extraction of inorganic acids...) on the uranium (VI) distribution coefficients enabled the constants of complex formation in the aqueous phase and extraction in the organic phase to be determined. These various properties were compared with those of dialkyl phosphoric and dithiophosphoric acids. The mechanisms established prove that sulfur donors ligands form stable complexes with UO 2 2+ ions although U(VI) is considered as a ''hard class a'' acceptor according to Ahrland's classification [fr

Study of the mechanism and kinetics of the reduction of uranyl ions in phosphoric acid solutions

International Nuclear Information System (INIS)

El Kacemi, K.; Tyburce, B.; Belcadi, S.

1982-01-01

The electrochemical reduction of uranyl ions in 0.1 to 9 M phosphoric acid has been investigated by polarography, cyclic voltammetry, chronopotentiometry and potentiostatic coulometry. In concentrated phosphoric acid solutions (H 3 PO 4 3 PO 4 concentrations. So, when the concentration of U(VI) increases and/or that of H 3 PO 4 reduces, the system becomes reversible. (author)

The distribution of n-caprylic acid between organic solvents and aqueous sodium sulfate solution

International Nuclear Information System (INIS)

Gloe, K.; Muehl, P.; Kholkin, A.I.; Gindin, L.M.

1981-01-01

The distribution of 14 C-labelled n-caprylic acid between n-decane, benzene, isoamyl acetate, diisopropyl ketone, isoamyl alcohol and an aqueous 0.6 molar sodium sulfate solution was studied. The distribution constants and the dimerisation constants were determined for the reactions HRsub((w)) reversible HRsub((org)) and 2 HRsub((org)) reversible (HR)sub(2(org)), respectively. Both the effect of the solvent on the acid distribution and the importance of such studies for the interpretation of liquid-liquid extraction equilibria are discussed. (author)

Removing ferric ions from concentrated acid leaching solution of an uranium ore by jarosite

International Nuclear Information System (INIS)

Song Huanbi; Hu Yezang

1997-01-01

The author expounds the fundamental rules of removing ferric ions by jarosite and presents results of removing ferric ions from concentrated acid curing-trickle leaching solution of an uranium ore. It turns out that the method can be applied to uranium hydrometallurgical process effectively

Decontamination effectiveness of mixtures of citric acid, oxalic acid and EDTA

International Nuclear Information System (INIS)

Speranzini, R.A.

1990-01-01

An experimental study of the decontamination effectiveness of citric acid, oxalic acid and EDTA mixtures was conducted to assess whether oxalic acid could be removed from decontamination solutions to minimize corrosion. In loop experiments, radioactive specimens from two boiling water reactors and one pressurized water reactor were suspended in solutions of single acids or in mixtures of reagents at total reagent concentrations of less than 0.1 wt% under conditions similar to those used to decontaminate reactor systems. Rate constants for dissolution of oxides and decontamination factors were measured. Based on the results, it was concluded that under certain conditions, oxalic acid was the most effective reagent for the dissolution of oxides. It was also found, however, that conditions under which effective dissolution occurred in solutions of oxalic acid and/or citric acid were difficult to define and control. EDTA was found to be an effective reagent for dissolution of oxides such that rates of dissolution in EDTA containing solutions at 117 degrees Celsius were comparable to rates in oxalic acid containing solutions. At 90 degrees Celsius, EDTA acted synergistically with oxalic acid such that the rate of dissolution of oxides in citric-acid/oxalic-acid/EDTA solutions was higher than in citric-acid/EDTA solutions. The rates of dissolution of oxides were significantly reduced when 60 mg/kg of ferric ion was added to the citric-acid/oxalic-acid, citric-acid/EDTA and citric-acid/oxalic-acid/EDTA solutions. It was concluded that effective decontaminations of BWR and PWR systems could be achieved with mixtures of citric acid and EDTA

Cefuroxime axetil: A commercially available drug as corrosion inhibitor for aluminum in hydrochloric acid solution

OpenAIRE

Ameh, Paul O.; Sani, Umar M.

2016-01-01

Cefuroxime axetil (CA) a prodrug was tested as corrosion inhibitor for aluminum in hydrochloric acid solution using thermometric, gasometric weight loss and scanning electron microscope (SEM) techniques. Results obtained showed that this compound has a good inhibiting properties for aluminum corrosion in acidic medium, with inhibition efficiencies values reaching 89.87 % at 0.5 g / L . It was also found out that the results from weight loss method are highly consistent with those obtained by ...

Corrosion and hydrogen absorption of commercially pure zirconium in acid fluoride solutions

International Nuclear Information System (INIS)

Yokoyama, Ken’ichi; Yamada, Daisuke; Sakai, Jun’ichi

2013-01-01

Highlights: •Zirconium corrodes and absorbs hydrogen in acid fluoride solutions. •Hydrogen thermal desorption is observed at 300–700 °C. •The resistance to hydrogen absorption of zirconium is higher than that of titanium. -- Abstract: The corrosion and hydrogen absorption of commercially pure zirconium have been investigated in acidulated phosphate fluoride (APF) solutions. Upon immersion in 2.0% APF solution of pH 5.0 at 25 °C, a granular corrosion product (Na 3 ZrF 7 ) deposits over the entire side surface of the specimen, thereby inhibiting further corrosion. In 0.2% APF solution, marked corrosion is observed from the early stage of immersion; no deposition of the corrosion product is observed by scanning electron microscopy. A substantial amount of hydrogen absorption is confirmed in both APF solutions by hydrogen thermal desorption analysis. The amount of absorbed hydrogen of the specimen immersed in the 2.0% APF solution is smaller than that in the 0.2% APF solution in the early stage of immersion. The hydrogen absorption behavior is not always consistent with the corrosion behavior. Hydrogen thermal desorption occurs in the temperature range of 300–700 °C for the specimen without the corrosion product. Under the same immersion conditions, the amount of absorbed hydrogen in commercially pure zirconium is smaller than that in commercially pure titanium as reported previously. The present results suggest that commercially pure zirconium, compared with commercially pure titanium, is highly resistant to hydrogen absorption, although corrosion occurs in fluoride solutions

Estimation of influence of a solution of a boric acid and temperatures on a isolation material from basalt fibers

International Nuclear Information System (INIS)

Pyshnova, V.V.; Skobelkina, T.N.; Yurchenko, V.G.; Knot'ko, A.V.; Putlyaev, V.I.

2006-01-01

Paper presents the results of investigation into long-term simultaneous effect of a medium (boric acid solution) and temperature on a thermal-insulating basalt fiber material. The basalt fiber clothes used at the NPP were tested. When evaluating simultaneous effect of boric acid solution and temperature one kept watch on density, compressibility, elasticity and diameter of fiber. According to the results of 30 day tests, the basic technical parameters of the thermal-insulating material have changed insignificantly [ru

Conductometric investigation of salt-free solutions of polyriboguanylic acid

International Nuclear Information System (INIS)

Kozlov, A.G.; Davydova, O.V.; Kargov, S.I.

1993-01-01

Salt-free solutions of various ionic forms of polyriboguanylic acid (poly(G)) were studied by the methods of conductometry and spectroscopy of annular dichroism. The Manning approach was employed to calculate transport characteristics and structural parameters of poly(G) on the basis of spectra permit putting poly(G) salts in two groups: the first one comprising NH 4 + -, Rb + -, K + -, Na + -, the second one - Cs + -, and Li + -poly(G). The assumption is made that Li + and Cs + ions, bound with concrete groups of polyanion in a specific way, can promote formation of a stable structure different from the one observed in the presence of the first group counterions. 25 refs., 3 figs

Effect of uranyl nitrate and free acid concentration in feed solution of gelation on UO2 kernel quality

International Nuclear Information System (INIS)

Masduki, B.; Wardaya; Widarmoko, A.

1996-01-01

An investigation on the effect of uranium and free nitric acid concentration of uranyl nitrate as feed of gelation process on quality of UO 2 kernel was done.The investigation is to look for some concentration of uranyl nitrate solutions those are optimum as feed for preparation of gelled UO 3 . Uranyl nitrate solution of various concentration of uranium (450; 500; 550; 600; 650; 700 g/l) and free nitric acid of (0.9; 1.0; 1.1 N) was made into feed solutions by adding urea and HMTA with mole ratio of urea/uranium and HMTA/uranium 2.1 and 2.0. The feed solutions were changed into spherical gelled UO 3 by dropping was done to get the optimum concentrations of uranyl nitrate solutions. The gelled UO 3 was soaked and washed with 2.5% ammonia solution for 17 hours, dried at 70 o C, calcined at 350 o C for 3 hours then reduced at 850 o C for 3 hours. At every step of the steps process the colour and percentage of well product of gelled UO 3 were noticed. The density and O/U ratio of end product (UO 2 kernel) was determined, the percentage of well product of all steps process was also determined. The three factor were used to chose the optimum concentration of uranyl nitrate solution. From this investigation it was concluded that the optimum concentration of uranyl nitrate was 600 g/l uranium with free nitric acid 0,9 - 1,0 N, the percentage of well product was 97% density of 6.12 - 4.8 g/cc and O/U ratio of 2.15 - 2.06. (author)

The vapour pressures over saturated aqueous solutions of DL-2-aminobutyric acid, 4-aminobutyric acid, sodium-D-gluconate, sodium hippurate, and potassium magnesium-L-aspartate

International Nuclear Information System (INIS)

Apelblat, Alexander; Korin, Eli

2008-01-01

Vapour pressures of water over saturated solutions of DL-2-aminobutyric acid, 4-aminobutyric acid, sodium-D-gluconate, sodium hippurate, and potassium magnesium-L-aspartate were determined over the (278 to 322) K temperature range. The determined vapour pressures were used to obtain the water activities, the molar enthalpies of vaporization, and the osmotic coefficients of sodium-D-gluconate

The vapour pressures over saturated aqueous solutions of DL-2-aminobutyric acid, 4-aminobutyric acid, sodium-D-gluconate, sodium hippurate, and potassium magnesium-L-aspartate

Energy Technology Data Exchange (ETDEWEB)

Apelblat, Alexander [Department of Chemical Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel)], E-mail: apelblat@bgu.ac.il; Korin, Eli [Department of Chemical Engineering, Ben Gurion University of the Negev, Beer Sheva 84105 (Israel)

2008-05-15

Vapour pressures of water over saturated solutions of DL-2-aminobutyric acid, 4-aminobutyric acid, sodium-D-gluconate, sodium hippurate, and potassium magnesium-L-aspartate were determined over the (278 to 322) K temperature range. The determined vapour pressures were used to obtain the water activities, the molar enthalpies of vaporization, and the osmotic coefficients of sodium-D-gluconate.

Electron inductive effects in the radiolysis of substituted phenylboronic acid solutions

International Nuclear Information System (INIS)

Brown, B.J.; Fitch, P.G.; Sangster, D.F.

1976-01-01

The pulse radiolysis of aqueous solutions of phenylboronic acid PhB(OH) 2 and its m-nitro and m-amino derivatives has been investigated. The transient optical absorption spectra indicate the presence of three intermediate species absorbing with independent maxima at 297, 317 and 400 nm. The 297-nm band has been assigned to the anion formed in an electron capture reaction, i.e. PhB(OH) 2 +epsilonsub(aq) - → PhB(OH) 2 - and the 317-nm band to cyclohexadienyl radicals formed from OH and H attack on OhB(OH) 2 . Hydroxyphenylboronic acid has been identified as the major stable radiation product. For each of the systems studied the respective yield and reactivity of observed intermediate species can be interpreted relative to the inductive effects of substituent groups in agreement with the Hammett relationship. (author)

Radiolysis of fatty acid esters in n-hexane solution in an atmosphere of nitrogen

International Nuclear Information System (INIS)

Kimura, Kazuo; Shirai, Kazuo

1975-01-01

There have been several problems in food preservation by irradiation. Deterioration of food components by irradiation is one of the most substantial subjects. This investigation was undertaken as a basic experiment to discuss the radiolysis of lipids in food irradiation. In the previous paper, radiolytic examination on six of methyl esters of fatty acids in n-hexane solution in the presence of air was reported. In the present work the same samples-methyl stearate (C sub(18:0)), methyl oleate (C sub(18:1)), methyl linoleate (C sub(18:2)), methyl linolenate (C sub(18:3)), methyl arachidate (C sub(20:0)) and methyl arachidonate (C sub(20:4)) were examined in an atmosphere of nitrogen. Samples in n-hexane solution were sealed in glass ampules after substituted with nitrogen. Preparations were treated with 60 Co-gamma-radiation at dose from 1.8 x 10 6 to 7.1 x 10 6 rads. These preparations were analyzed by gas chromatography, infrared spectrophotometry and iodine value determination. The results were as follows: 1. Generally speaking saturated acids were stable and unsaturated were unstable. 2. In unsaturated series, the high unsaturated fatty acids were more labile to gamma-irradiation and the more increased doses induced the more drastic decompositions. 3. It was observed by infrared spectra that some isomerization from cis to trans configuration occured at double bond systems in unsaturated fatty acids. (auth.)

Photophysics and Photochemistry of 2-Aminobenzoic Acid Anion in Aqueous Solution

Science.gov (United States)

Pozdnyakov, Ivan P.; Plyusnin, Victor F.; Grivin, Vjacheslav P.

2009-11-01

Nanosecond laser flash photolysis and absorption and fluorescence spectroscopy were used to study photochemical processes of 2-aminobenzoic acid anion (ABA-) in aqueous solutions. Excitation of this species gives rise to the ABA- triplet state to the ABA• radical and to the hydrated electron (eaq-). The last two species result from two-photon processes. In a neutral medium, the main decay channels of ABA- triplet state, the ABA• radical, and eaq- are T-T annihilation, recombination, and capture by the ABA- anion, respectively.

Yields of 2-deoxy-D-gluconic, D-gluconic and other sugar acids in gamma-irradiated aqueous solutions of D-glucose. [Gamma rays

Energy Technology Data Exchange (ETDEWEB)

Esterbauer, H; Schubert, J; Sanders, E B; Sweeley, C C [Pittsburgh Univ., Pa. (USA); Michigan State Univ., East Lansing (USA). Dept. of Biochemistry)

1977-03-01

The yields of 2-deoxy-D-gluconic, D-gluconic and other sugar acids from /sup 60/Co-gamma irradiated (dose-rate = 4 Krads/min) D-glucose solutions are reported. The acids produced upon radiolysis were separated from glucose and neutral products by anion exchange, assayed by gas chromatography of the trimethylsilyl derivatives, and definitive identification made by mass spectrometry. In He degassed, irradiated 0.055 M glucose G(2-deoxy-D-gluconic acid) = 0.62 and G(D-gluconic acid) = 0.20. The approximate G values for the other identified acids are: glyceric acid 0.03, 2-deoxy-tetronic acid 0.04, tetronic acid 0.03, 4-deoxypentonic acid 0.02, deoxyketogluconic acid 0.17. In N/sub 2/O saturated glucose solutions D-gluconic acid yields increased by a factor of approximately 1.9 while that of 2-deoxy-D-gluconic acid increased by a factor of only approximately 1.1.

Proton magnetic resonance studies in solutions of o- and p-hydroxy benzoic acids in dioxan

International Nuclear Information System (INIS)

Arulmozhi, V.; Srinivasa Rao, A.; Balasubramanian, V.

1990-01-01

High resolution proton(NMR) studies were carried out in solutions of o- and p-hydroxy benzoic acids(OHBA and PHBA) in dioxan (D) for several solute concentrations in the range of 0.01 to 0.10 mole fraction (mf). The spectra corresponding to OH and COOH protons could be distinguished in solutions of OHBA in D whereas solution of PHBA in D show only peak in the range of chemical shifts attributable to OH and COOH protons. In the solution of OHBA in dioxan the chemical shift of the proton of the hydroxyl group increases with increase of solute concentration and attains a maximum at a solute concentration of 0.04 mf and then decreases with further increase of solute concentration. For the carboxyl group, the chemical shift increase with increase of solute concentration and attians a maximum at 0.08 mf solute concentration. In solutions of PHBA in D the chemical shift of the single line observed increases with increase of solute concentration and attains a maximum at a solute concentration of 0.05 mf. The data are interpreted as due to formation of hydrogen bonds between the molecule of OHBA and PHBA and dioxan. The proton magnetic relaxation studies in the above solutions also confirm the above findings. (author). 6 refs., 5 figs

Adsorption of and acidic dye from aqueous solution by surfactant modified bentonite

International Nuclear Information System (INIS)

Bouberka, Z.; Khenifi, A.; Belkaid, N.; Ait Mahamed, H.; Haddou, B.; Derriche, Z.

2009-01-01

The aim of this paper is to study the adsorption of an acidic dye S. Y. 4 GL (i.e: Supranol yellow 4GL) from aqueous solution on inorgano-organo clay. Bentonite is a kind of natural clay with good exchanging ability. By exchanging its inter lamellar cations with Cetyltrimethylammonium bromide (CTAB) and hydroxy aluminic or chromium poly cations, the properties of natural bentonite can be greatly improved. (Author)

On the microstructure of organic solutions of mono-carboxylic acids: Combined study by infrared spectroscopy, small-angle neutron scattering and molecular dynamics simulations

Energy Technology Data Exchange (ETDEWEB)

Eremin, Roman A., E-mail: era@jinr.ru [Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation); Kholmurodov, Kholmirzo T. [Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation); International University “Dubna”, Dubna 141980 (Russian Federation); Petrenko, Viktor I. [Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation); Taras Shevchenko National University of Kyiv, Kyiv 03022 (Ukraine); Rosta, László [Wigner Research Centre for Physics, Hungarian Academy of Sciences, Budapest H-1525 (Hungary); Grigoryeva, Natalia A. [Faculty of Physics, Saint-Petersburg State University, 198504 Saint-Petersburg (Russian Federation); Avdeev, Mikhail V. [Joint Institute for Nuclear Research, Dubna 141980 (Russian Federation)

2015-11-05

Highlights: • The model of the scattering particle for a reliable SANS analysis is proposed. • The structural parameters of saturated mono-carboxylic acids in solutions are obtained. • The differences in nematic transitions correlate to solvation peculiarities. - Abstract: The data of infrared spectroscopy (IR), molecular dynamics (MD) simulations and small-angle neutron scattering (SANS) have been combined to conclude about the nanoscale structural organization of organic non-polar solutions of saturated mono-carboxylic acids with different alkyl chain lengths for diluted solutions of saturated myristic (C14) and stearic (C18) acids in benzene and decalin. In particular, the degree of dimerization was found from the IR spectra. The structural anisotropy of the acids and their dimers was used in the treatment of the data of MD simulations to describe the solute–solvent interface in a cylindrical approximation and show its rather strong influence on SANS. The corresponding scattering length density profiles were used to fit the experimental SANS data comprising the information about the acid molecule isomerization. The SANS data from concentrated solutions showed a partial self-assembling of the acids within the nematic transition is different for two solvents due to lyophobic peculiarities.

Solution of Azelaic Acid (20%), Resorcinol (10%) and Phytic Acid (6%) Versus Glycolic Acid (50%) Peeling Agent in the Treatment of Female Patients with Facial Melasma.

Science.gov (United States)

Faghihi, Gita; Taheri, Azam; Shahmoradi, Zabihollah; Nilforoushzadeh, Mohammad Ali

2017-01-01

Melasma, a common acquired disorder of hyperpigmentation, especially in women, is often resistant to therapy. This study was aimed to evaluate the efficacy and safety of azelaic acid, resorcinol and phytic acid solution in chemical peeling of melasma in comparison to 50% glycolic acid. This clinical trial was performed, on 42 female patients with bilateral melasma. Severity of melasma was assessed by melasma area and severity index (MASI). Combination of (20% azelaic acid + 10% resorcinol + 6% phytic acid) was used as a new peeling agent on the right side of the face and 50% glycolic acid on the left side every 2 weeks for 6 times. Follow-up was carried out for 3 months after the last session. Any decrease in MASI score and unwanted complications following peeling were evaluated and compared during the trial. Patients showed marked improvement as calculated with MASI score before and after treatment in both sides of the face. The efficacy of combination formula (azelaic acid, resorcinol and phytic acid) was similar to glycolic acid, but with fewer complications. There was no statistically difference in improvement between two groups ( P > 0.05). However, the patient's discomfort following procedures was significantly lower with azelaic acid, resorcinol and phytic compared with the glycolic acid peels ( P < 0.05) and there was the same duration in the beginning of the therapeutic response in both groups. Results showed that triple-combination was found to be an effective and safe peeling agent in the treatment of melasma and it was as effective as 50% glycolic acid peel.

Some features of transplutonium and rare earth elements extraction by HDEHP from lactic acid solutions

International Nuclear Information System (INIS)

Nikolaev, V.M.; Lebedev, V.M.; Lebedeva, L.S.

1986-01-01

The mechanisms of transplutonium (TPE) and rare earth elements (REE) extraction by HDEHP from lactic acid solutions are analysed in the literature. On the base of the known expressions and experimental data the model for TPE and REE extraction by HDEHP from lactic acid, accounting lactic acid and metal extraction as MeA 3 x3HA, MeLA 2 x2HA and MeLA 2 complexes, is suggested. The expression, permitting to estimate quantitatively the effect of TPE and REE complexing with lactic acid and the extraction of complex forms on the distribution coefficient of the extracted metal, is obtained. Comparison of calculational data with experimental ones show their good coincidence that confirms the rightness of the model accepted for extraction

An Exact Method to Determine the Conductivity of Aqueous Solutions in Acid-Base Titrations

Directory of Open Access Journals (Sweden)

Norma Rodríguez-Laguna

2015-01-01

Full Text Available Several works in the literature show that it is possible to establish the analytic equations to estimate the volume V of a strong base or a strong acid (Vb and Va, resp. being added to a solution of a substance or a mix of substances during an acid-base titration, as well as the equations to estimate the first derivative of the titration plot dpH/dV, and algebraic expressions to determine the buffer β capacity with dilution βdil. This treatment allows establishing the conditions of thermodynamic equilibria for all species within a system containing a mix of species from one or from various polyacid systems. The present work shows that it is possible to determine exactly the electric conductivity of aqueous solutions for these Brønsted acid-base titrations, because the functional relation between this property and the composition of the system in equilibrium is well known; this is achieved using the equivalent conductivity λi values of each of the ions present in a given system. The model employed for the present work confirms the experimental outcomes with the H2SO4, B(OH3, CH3COOH, and H3PO4 aqueous solutions’ titration.

Composition, structure and electrical properties of alumina barrier layers grown in fluoride-containing oxalic acid solutions

Energy Technology Data Exchange (ETDEWEB)

Jagminas, A. [Institute of Chemistry, A. Gostauto 9, LT-01108 Vilnius (Lithuania)], E-mail: jagmin@ktl.mii.lt; Vrublevsky, I. [Department of Microelectricals, Belarusian State University of Informatics and Radioelectricals, 6 Brovka Street, Minsk 220013 (Belarus); Kuzmarskyte, J.; Jasulaitiene, V. [Institute of Chemistry, A. Gostauto 9, LT-01108 Vilnius (Lithuania)

2008-04-15

The composition, structure and electrical properties of alumina barrier layers grown by anodic oxidation in F{sup -}-containing (FC) and F{sup -}-free (FF) oxalic acid solutions were studied using the re-anodizing/dissolution technique, Fourier-transformed infrared and X-ray photoelectron spectroscopy. These results confirmed formation in FC anodizing solutions of films structurally different from ones grown in FF oxalic acid baths. It was found that the barrier layer of FC alumina films is composed of two layers differing in the dissolution rate. These differences are related to the formation in the FC electrolyte of a barrier layer composed of a more microporous outer part and a thin, non-porous and non-scalloped inner part consisting of aluminum oxide and aluminum fluoride.

Determination of plutonium in nitric acid solutions - Method by oxidation by cerium(IV), reduction by iron(II) ammonium sulfate and amperometric back-titration with potassium dichromate

International Nuclear Information System (INIS)

1987-01-01

This International Standard specifies a precise and accurate analytical method for determining plutonium in nitric acid solutions. Plutonium is oxidized to plutonium(VI) in a 1 mol/l nitric acid solution with cerium(IV). Addition of sulfamic acid prevents nitrite-induced side reactions. The excess of cerium(IV) is reduced by adding a sodium arsenite solution, catalysed by osmium tetroxide. A slight excess of arsenite is oxidized by adding a 0.2 mol/l potassium permanganate solution. The excess of permanganate is reduced by adding a 0.1 mol/l oxalic acid solution. Iron(III) is used to catalyse the reduction. A small excess of oxalic acid does not interfere in the subsequent plutonium determination. These reduction and oxidation stages can be followed amperometrically and the plutonium is left in the hexavalent state. The sulfuric acid followed by a measured amount of standardized iron(II) ammonium sulfate solution in excess of that required to reduce the plutonium(VI) to plutonium(IV) is added. The excess iron(II) and any plutonium(III) formed to produce iron(III) and plutonium(IV) is amperometrically back-titrated using a standard potassium dichromate solution. The method is almost specifically for plutonium. It is suitable for the direct determination of plutonium in materials ranging from pure product solutions, to fast reactor fuel solutions with a uranium/plutonium ratio of up to 10:1, either before or after irradiation

Acid-base and hemodynamic status of patients with intraoperative hemorrhage using two solution types: Crystalloid Ringer lactate and 1.3% sodium bicarbonate in half-normal saline solution.

Science.gov (United States)

Hashemi, Sayed Jalal; Heidari, Sayed Morteza; Yaraghi, Ahmad; Seirafi, Reza

2016-01-01

Intraoperative hemorrhage is one of the problems during surgery and, if it happens in a high volume without an immediate action to control, it can be fatal. Nowadays, various injectable solutions are used. The aim of this study was to compare the acid-base and hemodynamic status of the patient using two solutions, Ringer lactate and 1.3% sodium bicarbonate, in half saline solution. This clinical trial was performed at the Al-Zahra Hospital in 2013 on 66 patients who were randomly selected and put in two studied groups at the onset of hemorrhage. For the first group, crystalloid Ringer lactate solution and for the second group, 1.3% sodium bicarbonate in half-normal saline solution was used. Electrocardiogram, heart rate, O2 saturation non-invasive blood pressure and end-tidal CO2 were monitored. The arterial blood gas, blood electrolytes, glucose and blood urea nitrogen were measured before serum and blood injection. After the infusion of solutions and before blood transfusions, another sample was sent for measurement of blood parameters. Data were analyzed using SPSS software. The mean arterial pressure was significantly higher in the second group than in the first group at some times after the infusion of solutions. pHh levels, base excess, bicarbonate, sodium, strong ion differences and osmolarity were significantly greater and potassium and chloride were significantly lower in the second group than in the first group after the infusion of solutions. 1.3% sodium bicarbonate in half-normal saline solution can lead to a proper correction of hemodynamic instability. By maintaining hemodynamic status, osmolarity and electrolytes as well as better balance of acid-base, 1.3% sodium bicarbonate solution in half-normal saline solution can be more effective than Ringer lactate solution during intraoperative bleeding.

Solvent Extraction of Tungsten(VI) from Moderate Hydrochloric Acid Solutions with LIX 63

Energy Technology Data Exchange (ETDEWEB)

Truong, Hoai Thanh; Lee, Man Seung [Mokpo National University, Jeollanamdo (Korea, Republic of); Kim, Yong Hwan [Incheon Technology Service Centre, Incheon (Korea, Republic of)

2017-06-15

The solvent extraction of tungsten(VI) from hydrochloric acid solutions using 5,8-diethyl-7-hydroxydodecan-6-one oxime (LIX 63) was analyzed in solutions having an initial pH range from 2 to 5, by varying the concentration of metal and extractant. In our experimental range, the cationic exchange reaction as well as the solvation reaction occurred simultaneously. The cation exchange reaction was identified by applying a slope analysis method to the extraction data. The existence of cationic tungsten(VI) species was confirmed by ion exchange experiments with Diphonix resin at pH 3. Further study is needed to identify the nature of this tungsten cationic species.

Oxalic acid as a liquid dosimeter for absorbed dose measurement in large-scale of sample solution

International Nuclear Information System (INIS)

Biramontri, S.; Dechburam, S.; Vitittheeranon, A.; Wanitsuksombut, W.; Thongmitr, W.

1999-01-01

This study shows the feasibility for, applying 2.5 mM aqueous oxalic acid solution using spectrophotometric analysis method for absorbed dose measurement from 1 to 10 kGy in a large-scale of sample solution. The optimum wavelength of 220 nm was selected. The stability of the response of the dosimeter over 25 days was better than 1 % for unirradiated and ± 2% for irradiated solution. The reproducibility in the same batch was within 1%. The variation of the dosimeter response between batches was also studied. (author)

Studies on Benzo-DODA encapsulated polymeric beads for separation of Pu from acidic solution

International Nuclear Information System (INIS)

Singh, K.K.; Panja, S.; Kumar, M.; Ruhela, R.; Tripathi, S.C.; Singh, A.K.; Hubli, R.C.; Bajaj, P.N.

2014-01-01

High level liquid waste (HLLW) generated during the reprocessing of spent fuel contains a few mg of Pu per litre of waste volume. Therefore, there is a need for selective separation of Pu from above solution as well as other such acidic waste streams. The widely used technology for separation and recovery of metal ions from radioactive wastes is liquid-liquid extraction.Though, such technologies play major role in all the bulk separation processes, they have marked limitations involving the losses of extractant in aqueous phase, third phase problems at higher metal loading, etc. These limitations have necessitated the exploration of advance, more efficient and technically feasible alternatives. In this regard it is thought that solid-liquid based Extractant Encapsulated Polymeric Beads (EEPBs) may solve some of the problems. Benzodioxodiamide (BenzoDODA) is a recently reported extractant for the separation of plutonium from radioactive waste, containing nitric acid. BenzoDODA extractant encapsulated polymeric beads were prepared by phase inversion technique and found to be quite stable as no significant structural deformation or leaching out of the extractant was observed in 4.0 M HNO 3 solution, up to studied equilibration time of 8 days. These beads have been characterized by FT-IR, TGA and SEM techniques to gain insight into their structure and morphology. Morphology and porosity of the beads, as studied by the SEM analysis, indicate that the surface of the beads is quite rough, and has enough porosity. Thermo gravimetric analysis of the synthesized composite beads shows a weight loss of ∼74% during the heating from room temperature to 120℃, due to the loss of water present in the swollen beads. Such high water content also confirms that the beads have enough porosity for efficient exchange of metal ions.The synthesized beads were evaluated, for their ability to absorb Pu from acidic solution. The kinetics measurement showed that about 45 min of

[Effects of Low-Molecular-Weight Organic Acids on the Speciation of Pb in Purple Soil and Soil Solution].

Science.gov (United States)

Liu, Jiang; Jiang, Tao; Huang, Rong; Zhang, Jin-zhong; Chen, Hong

2016-04-15

Lead (Pb) in purple soil was selected as the research target, using one-step extraction method with 0.01 mol · L⁻¹ sodium nitrate as the background electrolyte to study the release effect of citric acid (CA), tartaric acid (TA) and acetic acid (AC) with different concentrations. Sequential extraction and geochemical model (Visual Minteq v3.0) were applied to analyze and predict the speciation of Pb in soil solid phase and soil solution phase. Then the ebvironmental implications and risks of low-molecule weight organic acid (LMWOA) on soil Pb were analyzed. The results indicated that all three types of LMWOA increased the desorption capacity of Pb in purple soil, and the effect followed the descending order of CA > TA > AC. After the action of LMWOAs, the exchangeable Pb increased; the carbonate-bound Pb and Fe-Mn oxide bound Pb dropped in soil solid phase. Organic bound Pb was the main speciation in soil solution phase, accounting for 45.16%-75.05%. The following speciation of Pb in soil solution was free Pb, accounting for 22.71%-50.25%. For CA and TA treatments, free Pb ions and inorganic bound Pb in soil solution increased with increasing LMWOAs concentration, while organic bound Pb suffered a decrease in this process. An opposite trend for AC treatment was observed compared with CA and TA treatments. Overall, LMWOAs boosted the bioavailability of Pb in purple soil and had a potential risk to contaminate underground water. Among the three LMWOAs in this study, CA had the largest potential to activate soil Pb.

Temperature influence on corrosion rate of armco iron in acid solutions

International Nuclear Information System (INIS)

Perboni, G.; Rocchini, G.

1986-01-01

An experimental study of the behaviour of Armco iron and several steels in acid solutions (HCl, H 2 SO 4 , H 3 PO 4 ) has been undertaken to determine the temperature effect on dissolution rate. The test temperatures were 30, 45, 60, 75 and 90 deg C. The activation heat was determined by application of the Arrhenius law from colorimetric and electrochemical data. Investigation results obtained by both methods were represented diagrammatically and showed a good agreement, though the discrepancy in the data increased with test temperature

Assorted interactions of amino acids prevailing in aqueous vitamin C solutions probed by physicochemical and ab-initio contrivances

Science.gov (United States)

Das, Koyeli; Roy, Milan Chandra; Rajbanshi, Biplab; Roy, Mahendra Nath

2017-11-01

Qualitative and quantitative analysis of molecular interaction prevailing in tyrosine and tryptophan in aqueous solution of vitamin C have been probed by thermophysical properties. The apparent molar volume (ϕV), viscosity B-coefficient, molal refraction (RM) of tyrosine and tryptophan have been studied in aqueous vitamin C solutions at diverse temperatures via Masson equation which deduced solute-solvent and solute-solute interactions, respectively. Spectroscopic study along with physicochemical and computational techniques provides lots of interesting and highly significant insights of the model biological systems. The overall results established strong solute-solvent interactions between studied amino acids and vitamin C mixture in the ternary solutions.

Plant refuses driven biochar: Application as metal adsorbent from acidic solutions

Directory of Open Access Journals (Sweden)

Puja Khare

2017-05-01

Full Text Available Biochar prepared from aromatic spent was used as adsorbent for assessing its removal capacity of cadmium, chromium, copper and lead from aqueous acidic solutions. For the optimization of the processes, separate experiments were setup in fixed bed columns of biochar prepared from different biomasses in variable sizes at different temperatures, metal concentrations, flow rate and time. The effect of the above parameters on adsorption of metals was assessed in terms of maximum adsorption capacity, kinetics, theorem and thermodynamics. Results show that maximum removal of each metal was 60 mg/g. The adsorption equilibrium data obeyed the Freundlich model and the kinetic data were well described by the pseudo-second-order model. The adsorption process is believed to proceed by an initial surface adsorption followed by intra-particle diffusion. In this regard to the proposed mechanism, modeling results implied that exchange of the hydrogen occurs during the low loading of metal. Opposite is true for the calcium, magnesium and sodium ions. Thermodynamic studies revealed the feasibility and endothermic nature of the system. Treatment of acidic mine water with biochar suggests that it buffers the acid and is capable of efficient removal of these metals.

[Enhanced electro-chemical oxidation of Acid Red 3R solution with phosphotungstic acid supported on gamma-Al2O3].

Science.gov (United States)

Yue, Lin; Wang, Kai-Hong; Guo, Jian-Bo; Yang, Jing-Liang; Liu, Bao-You; Lian, Jing; Wang, Tao

2013-03-01

Supported phosphotungstic acid catalysts on gamma-Al2O3 (HPW/gamma-Al2O3) were prepared by solution impregnation and characterized by FTIR, XRD, TG-DTA and SEM. The heteropolyanion shows a Keggin structure. Electro-chemical oxidation of Acid Red 3R was investigated in the presence of HPW supported on gamma-Al2O3 as packing materials in the reactor. The results show that HPW/gamma-Al2O3 has a good catalytic activity for decolorization of Acid Red 3R. When HPW loading was 4.6%, pH value of Acid Red 3R was 3, the voltage was 25.0 V, air-flow was 0.04 m3 x h(-1), and electrode span was 3.0 cm, the decolorization efficiency of Acid Red 3R can reach 97.6%. The removal rate of color had still about 80% in this electro-chemical oxidation system, after HPW/gamma-Al2O3 was used for 10 times, but active component loss existed. The interim product was analyzed by means of Vis-UV absorption spectrum. It shows that the conjugated structure of dye is destroyed primarily.

Aspartic acid interaction with cobalt(II) in dilute aqueous solution: A {sup 57}Co emission Moessbauer spectroscopic study

Energy Technology Data Exchange (ETDEWEB)

Kamnev, Alexander A.; Tugarova, Anna V. [Institute of Biochemistry and Physiology of Plants and Microorganisms, Russian Academy of Sciences (Russian Federation); Kovacs, Krisztina; Homonnay, Zoltan, E-mail: homonnay@ludens.elte.hu; Kuzmann, Erno; Vertes, Attila [Eoetvoes Lorand University, Institute of Chemistry (Hungary)

2012-03-15

Emission ({sup 57}Co) Moessbauer spectra of the aspartic acid-{sup 57}CoCl{sub 2} system were measured at T = 80 K in frozen aqueous solution and in the form of a dried residue of this solution. The Moessbauer spectra, besides a weak contribution from after-effects, showed two Fe{sup 2 + }/Co{sup 2 + } components which were ascribed to octahedrally and tetrahedrally coordinated {sup 57}Co{sup II} microenvironments in the Asp-cobalt(II) complex. This dual coordination mode may be due to the involvement of the second terminal carboxylic group of aspartic acid in the coordination sphere of Co.

Coefficients of interphase distribution and Gibbs energy of the transfer of nicotinic acid from water into aqueous solutions of ethanol and dimethylsulfoxide

Science.gov (United States)

Grazhdan, K. V.; Gamov, G. A.; Dushina, S. V.; Sharnin, V. A.

2012-11-01

Coefficients of the interphase distribution of nicotinic acid are determined in aqueous solution systems of ethanol-hexane and DMSO-hexane at 25.0 ± 0.1°C. They are used to calculate the Gibbs energy of the transfer of nicotinic acid from water into aqueous solutions of ethanol and dimethylsulfoxide. The Gibbs energy values for the transfer of the molecular and zwitterionic forms of nicotinic acid are obtained by means of UV spectroscopy. The diametrically opposite effect of the composition of binary solvents on the transfer of the molecular and zwitterionic forms of nicotinic acid is noted.

Liquid-liquid extraction of chromium (VI) from sulfuric acid solutions using tri-n-dodecylamine/kerosene

International Nuclear Information System (INIS)

Stas, J.

2008-01-01

Extraction of chromium (VI) from sulfuric acid solutions with tri-n-dodecylamine containing octanol-1 as a modifier in kerosene was investigated. All parameters influencing the extraction of chromium (VI) (time of agitation, concentrations of chromium (VI), sulfuric acid, tri-n-dodecylamine and temperature) were studied. Forst of all, tri-n-dodecylamine reacts with sulfuric acid to form tri-n-dodecylamine sulfate and bisulfate salts, then, dichromate ions is extracted by amine bisulfate. The mathematical treatment of the obtained date enabled us to calculate the formation of equilibrium constant of (TDAH) 2 SO 4 TDAHHSO 4 and (TDAH) 2 Cγ 2 O 7 at 25 Centigrade and have been found to be K 1 =10 9.642 (14/mol 4 ), K 2 = 10 -0.899 (L/mol) and K ex 10 10.55 respectively. Stripping of more than 99% of chromium (VI) from the organic phase of tri-n-dodecylamine/kerosene can be easily achieved in two stages using 0.05 M sodium carbonate solution. The synergistic effect of tri-n-butylphosphate and tri-n-octylphosphine oxide on the extraction of chromium (VI) were also studied. (author)

Application of solution-mineral equilibrium chemistry to solution mining of uranium ores

International Nuclear Information System (INIS)

Riese, A.C.; Popp, C.J.

1979-01-01

The tests described were undertaken to determine the extent to leach solution-rock interactions with uranium-bearing ore obtained from the Mariano Lake mine. Leach solutions of an acidic (H/sub 2/O/sub 4/-sulfuric acid) and basic (NaHCO/sub 3/-sodium bicarbonate) nature were tested, in addition to a leach solution containing potassium chloride and sulfuric acid (KCl/H/sub 2/SO/sub 4/). The latter solution was chosen in an attempt to equilibrate the aqueous phase with the rock-forming silicate minerals and minimize adverse effects such as clay formation, porosity loss, and lixiviant loss. 29 refs

Influence of Acidity on Uranyl Nitrate Association in Aqueous Solutions: A Molecular Dynamics Simulation Study

International Nuclear Information System (INIS)

de Almeida, Valmor F.; Cui, Shengting; Khomami, Bamin; Ye, Xianggui; Smith, Rodney Bryan

2010-01-01

Uranyl ion complexation with water and nitrate is a key aspect of the uranium/plutonium extraction process. We have carried out a molecular dynamics simulation study to investigate this complexation process, including the molecular composition of the various complex species, the corresponding structure, and the equilibrium distribution of the complexes. The observed structures of the complexes suggest that in aqueous solution, uranyls are generally hydrated by 5 water molecules in the equatorial plane. When associating with nitrate ions, a water molecule is replaced by a nitrate ion, preserving the five-fold coordination and planar symmetry. Analysis of the pair correlation function between uranyl and nitrate suggests that nitrates bind to uranyl in aqueous solution mainly in a monodentate mode, although a small portion of bidentates occur. Dynamic association and dissociation between uranyls and nitrates take place in aqueous solution with a substantial amount of fluctuation in the number of various uranyl nitrate species. The average number of the uranyl mononitrate complexes shows a dependence on acid concentration consistent with equilibrium-constant analysis, namely, the concentration of [UO2NO3]+ increases with nitric acid concentration.

Capillary electrophoresis of chitooligosaccharides in acidic solution: simple determination using a quaternary-ammonium-modified column and indirect photometric detection with crystal violet.

Science.gov (United States)

Hattori, Toshiaki; Anraku, Nobuhiro; Kato, Ryo

2010-02-01

Five chitosan oligosaccharides were separated in acidic aqueous solution by capillary electrophoresis (CE) with indirect photometric detection using a positively coated capillary. Electrophoretic mobility of the chitooligosaccharides (COSs) depended on the number of monomer units in acidic aqueous solution, similar to other polyelectrolyte oligomers. The separation was developed in nitric acid aqueous solution at pH 3.0 with 1 mM Crystal Violet, using a capillary positively coated with N-trimethoxypropyl-N,N,N-trimethylammonium chloride. The limit of the detection for chitooligosaccharides with two to six saccharide chains was less than 5 microM. CE determination of an enzymatically hydrolyzed COS agreed with results from HPLC. 2009 Elsevier B.V. All rights reserved.

Solution of Azelaic Acid (20%, Resorcinol (10% and Phytic Acid (6% Versus Glycolic Acid (50% Peeling Agent in the Treatment of Female Patients with Facial Melasma

Directory of Open Access Journals (Sweden)

Gita Faghihi

2017-01-01

Full Text Available Background: Melasma, a common acquired disorder of hyperpigmentation, especially in women, is often resistant to therapy. This study was aimed to evaluate the efficacy and safety of azelaic acid, resorcinol and phytic acid solution in chemical peeling of melasma in comparison to 50% glycolic acid. Materials and Methods: This clinical trial was performed, on 42 female patients with bilateral melasma. Severity of melasma was assessed by melasma area and severity index (MASI. Combination of (20% azelaic acid + 10% resorcinol + 6% phytic acid was used as a new peeling agent on the right side of the face and 50% glycolic acid on the left side every 2 weeks for 6 times. Follow-up was carried out for 3 months after the last session. Any decrease in MASI score and unwanted complications following peeling were evaluated and compared during the trial. Results: Patients showed marked improvement as calculated with MASI score before and after treatment in both sides of the face. The efficacy of combination formula (azelaic acid, resorcinol and phytic acid was similar to glycolic acid, but with fewer complications. There was no statistically difference in improvement between two groups (P > 0.05. However, the patient's discomfort following procedures was significantly lower with azelaic acid, resorcinol and phytic compared with the glycolic acid peels (P < 0.05 and there was the same duration in the beginning of the therapeutic response in both groups. Conclusion: Results showed that triple-combination was found to be an effective and safe peeling agent in the treatment of melasma and it was as effective as 50% glycolic acid peel.

Investigation of antimony extraction from nitric acid solutions by tributyl phosphate

International Nuclear Information System (INIS)

Lakaev, V.S.; Smelov, V.S.

1988-01-01

The effect of iodide, hydrogen and pertechnetate ions on antimony extraction by tri-n-butyl phosphate (TBP) from aqueous nitric acid solutions under irradiated nuclear fuel processing is investigated at room temperature. The coefficients of antimony distribution are shown to increase at the presence of technetium ions 2-3 times and iodine ions - 100 and more times. Variation of hydrogen ion concentration does not affect antimony extraction. The schemes of the mechanism of antimony extraction at the pressence of iodide and pertechnetate ions are presented. Compositions of the formed compounds are given

Acid-base and electrolyte status during normovolemic hemodilution with succinylated gelatin or HES-containing volume replacement solutions in rats.

Directory of Open Access Journals (Sweden)

Johanna K Teloh

Full Text Available BACKGROUND: In the past, several studies have compared different colloidal replacement solutions, whereby the focus was usually on the respective colloid. We therefore systematically studied the influence of the carrier solution's composition of five approved colloidal volume replacement solutions (Gelafundin, Gelafusal, Geloplasma, Voluven and Volulyte on acid-base as well as electrolyte status during and following acute severe normovolemic hemodilution. The solutions differed in the colloid used (succinylated gelatin vs. HES and in the presence and concentration of metabolizable anions as well as in their electrolyte composition. METHODS: Anesthetized Wistar rats were subjected to a stepwise normovolemic hemodilution with one of the solutions until a final hematocrit of 10%. Subsequent to dilution (162 min, animals were observed for an additional period (150 min. During dilution and observation time blood gas analyses were performed eight times in total. Additionally, in the Voluven and Volulyte groups as well as in 6 Gelafundin animals, electrolyte concentrations, glucose, pH and succinylated gelatin were measured in urine and histopathological evaluation of the kidney was performed. RESULTS: All animals survived without any indications of injury. Although the employed solutions differed in their respective composition, comparable results in all plasma acid-base and electrolyte parameters studied were obtained. Plasma pH increased from approximately 7.28 to 7.39, the plasma K(+ concentration decreased from circa 5.20 mM to 4.80-3.90 mM and the plasma Cl(- concentration rose from approximately 105 mM to 111-120 mM. Urinary analysis revealed increased excretion of K(+, H(+ and Cl(-. CONCLUSIONS: The present data suggest that the carrier solution's composition with regard to metabolizable anions as well as K(+, Ca(2+ only has a minor impact on acid-base and electrolyte status after application of succinylated gelatin or HES-containing colloidal

Crystal phase evolution of TiO2 nanoparticles with reaction time in acidic solutions studied via freeze-drying method

International Nuclear Information System (INIS)

Shin, Hyunho; Jung, Hyun Suk; Hong, Kug Sun; Lee, Jung-Kun

2005-01-01

The crystal phase evolution of TiO 2 nanoparticles, during hydrolysis and condensation of titanium tetraisopropoxide, was quenched at various reaction times by a freeze-drying method, followed by various characterizations. Three types of solutions with different acid input times were studied: (1) addition in infinite time (no addition) (2) addition at 24h after the hydrolysis/condensation reaction started, and (3) addition from the beginning of the reaction. The acid-free solution yielded amorphous TiO 2 , which transformed to anatase very slowly. The acid input in 24h resulted in a fast transformation of amorphous to a metastable anatase having a highly distorted atomic arrangement: thereby its transformation to a more stable phase, rutile, was suitable. The acid addition from the beginning of the reaction yielded the formation of a relatively stable anatase from the hydrolysis seed, thereby the subsequent transformation to rutile was sluggish

The use of ion-selective membranes for the recovery of sulphuric acid out of contaminated solutions. Comparing electrodialysis, electro electrodialysis and diffusion dialysis

International Nuclear Information System (INIS)

Cattoir, S.

1998-02-01

The amount of waste arising from dismantled reactors is minimized by decontamination processes. These processes result in contaminated effluents, containing acid and metal salts. The quantity of final waste can be substantially reduced when the acid is extracted out of the decontamination effluents prior to neutralisation. This report discusses three membrane techniques for the displacement of acids out of mixed acid/salt solutions: electrodialysis (ED), electro electrodialysis (EED) and diffusion dialysis (DD). EED uses an electrical potential difference across an anion-selective membrane; DD uses a concentration difference across an anion-selective membrane; ED uses an electrical potential difference, across an anion- and a cation-selective membrane. EED can displace up to 90% of the sulphuric acid, the amount of metal ions in the displaced-acid solution is less than 1% of the ions in the original contaminated solution. Treatment costs are estimated to about 18 Belgian Francs per litre. In DD the purity of the displaced acid is comparable to EED. Treatment costs are about 21 Belgian Francs per litre. In ED 90% acid-displacement is easily reached, but 5% metal ions are also displaced. Treatment costs are about 6 Belgian Francs per litre. Therefore, in spite of the lower purity of the resulting acid, ED is economically speaking the best choice

Influence of biopolymers on the solubility of branched-chain amino acids and stability of their solutions.

Science.gov (United States)

Hong, Chi Rac; Lee, Gyu Whan; Paik, Hyun-Dong; Chang, Pahn-Shick; Choi, Seung Jun

2018-01-15

This study confirmed the possibility of biopolymer-type stabilizers to increase the saturation concentration of branched-chain amino acids by preventing their crystallization/precipitation. Although microfluidization increased the initial solubility, it failed to increase the saturation concentration of the branched-chain amino acids. The saturation concentration of the branched-chain amino acids increased from 3.81% to 4.42% and 4.85% after the incorporation of food hydrocolloids and proteins, respectively. However, the branched-chain amino acids:stabilizer ratio did not affect the solubility. In the case of food hydrocolloid-based solutions, crystal formation and growth of branched-chain amino acids occurred during storage, resulting in the precipitation of branched-chain amino acid crystals. However, food proteins effectively increased the stability of the solubilized branched-chain amino acids. The improved solubility and stability of the solubilized branched-chain amino acids could be attributed to interactions between the functional groups (carboxyl, amine, sulfate, aliphatic, aromatic, etc.) of the stabilizer and the branched-chain amino acid molecules. Copyright © 2017 Elsevier Ltd. All rights reserved.

Evaluation of poly (aspartic acid sodium salt) as a draw solute for forward osmosis.

Science.gov (United States)

Gwak, Gimun; Jung, Bokyung; Han, Sungsoo; Hong, Seungkwan

2015-09-01

Poly (aspartic acid sodium salt) (PAspNa) was evaluated for its potential as a novel draw solute in forward osmosis (FO). The inherent advantages of PAspNa, such as good water solubility, high osmotic pressure, and nontoxicity, were first examined through a series of physicochemical analyses and atomic-scale molecular dynamics simulations. Then, lab-scale FO tests were performed to evaluate its suitability in practical processes. Compared to other conventional inorganic solutes, PAspNa showed comparable water flux but significantly lower reverse solute flux, demonstrating its suitability as a draw solute. Moreover, fouling experiments using synthetic wastewater as a feed solution demonstrated that PAspNa reversely flowed to the feed side reduced inorganic scaling on the membrane active layer. The recyclability of PAspNa was studied using both nanofiltration (NF) and membrane distillation (MD) processes, and the results exhibited its ease of recovery. This research reported the feasibility and applicability of FO-NF or FO-MD processes using PAspNa for wastewater reclamation and brackish water desalination. Copyright © 2015 Elsevier Ltd. All rights reserved.

Immobilization of citric acid solutions in portland cement; Imobilizacao de solucoes de acido citrico em cimento Portland

Energy Technology Data Exchange (ETDEWEB)

Lopes, Valdir M.; Rzyski, Barbara M. [Instituto de Pesquisas Energeticas e Nucleares (IPEN), Sao Paulo, SP (Brazil)

1997-12-01

Decontamination processes by using citric acid on certain items used in the nuclear area, can result in large volumes of liquid wastes with low activity or effluents, contaminated with uranium and some elements dangerous to the environment. A great number of installations that have decontamination processes adopt the zero discharge philosophy. So, one of the forms to isolate the solutions is by reducing its volume through the evaporation process. The generated must can be neutralized and encapsulated or immobilized in Portland cement. This work propose a chemical technique to destroy the citric acid in the decontamination solutions instead of neutralization and, depending on the installation convenience, a direct cement immobilization of these solutions or of the evaporation mud. The results obtained in this work involve data about the workability, setting time and mechanical resistance, after 28 days of sealed cure, for samples with water-cement ratios of 4, 0.5 and 0.6, by weight. (author). 5 refs., 2 tabs.

Ruthenium (4) and ruthenium (3) state in hydrochloric acid solutions under microwave irradiation