PROPIEDADES MECÁNICAS DE PELÍCULAS HÍBRIDAS (ORGÁNICO-INORGÁNICO SOBRE ACERO INOXIDABLE 304 Mechanical Properties of Hybrid Films (Organic-Inorganic on Stainless Steel 304

Directory of Open Access Journals (Sweden)

Jorge H. Bautista-Ruiz

2011-12-01

Full Text Available This article shows the creation of ceramic films of the SiO2-TiO2 Organic Polymer hybrid system from Tetraethyl-Orthosilicate (Si (OC2H54 and Titanium Tetrabutoxide (Ti(OBu4 synthesized through the sol-gel method in several volumetric concentrations of precursors. This hybrid system was deposited on AISI 304 stainless steel substrates through the dip-coating technique. Feasibility for obtaining hybrid and homogeneous coatings on this type of substrate and evaluating the surface properties was studies. For such a purpose, the coating microhardness and adhesion were studies. Additionally, the film surface was characterized through the SEM (Scanning Electron Microscopy. The study concluded that characteristics of films change in function of the volumetric amount of precursors used for creating films.Este trabajo muestra la conformación de películas cerámicas del sistema híbrido SiO2-TiO2-Polímero Orgánico, a partir de tetraetil-ortosilicato (Si (OC2H54, y tetra-butoxido de titanio (Ti(OBu4 y sintetizado por el método sol-gel en diferentes concentraciones volumétricas de los precursores. Este sistema híbrido se depositó sobre sustratos de acero inoxidable AISI 304 mediante la técnica de inmersión (dip-coating. Se estudió la viabilidad de obtener recubrimientos híbridos homogéneos sobre este tipo de sustrato y evaluar las propiedades superficiales. Para tal efecto, se estudió microdureza y adhesión del recubrimiento. Adicionalmente, se caracterizó la superficie de las películas por microscopía electrónica de barrido (MEB. Del estudio se concluye que las características de las películas cambian en función de la cantidad volumétrica de los precursores utilizados en la conformación de las mismas.

Estudio de la influencia microbiológica en la corrosión de latones (UNS C68700, UNS C443 y acero inoxidable AISI 316;

Directory of Open Access Journals (Sweden)

Ohanian, Mauricio

2014-06-01

Full Text Available Microorganisms may play an important role in the corrosion process and generate conditions which affect the rate and/or the mechanism of deterioration. They become visible by the formation of biofilms: clusters of microorganisms and extracellular polymers. These biofilms affect not only the durability of the material, but also reduce the heat transfer. The present work studied the growth of aerobic and anaerobic heterotrophic microorganisms and sulfate reducing bacteria on aluminum brass (UNS C68700, admiralty brass (UNS C443 and stainless steel AISI 316 in exposure experiments held in the Bay of Montevideo (Uruguay. The influence of the biofilm growth on the corrosion behavior was studied by electrochemical techniques: polarization curves and Electrochemical Impedance Spectroscopy (EIS. The selection of the most suitable material for the exposure conditions is discussed and hypotheses of the corrosion mechanism are presented. Although stainless steel AISI 316 presented the lowest corrosion rate it showed localized deterioration.Los microorganismos influyen de manera significativa en el proceso corrosivo y generan condiciones que afectan la velocidad y/o el mecanismo de deterioro. Su presencia se manifiesta por la formación de bio-películas: conglomerados de bacterias y polímeros extracelulares. Dichas bio-películas afectan la durabilidad del material, la velocidad de flujo y la transferencia de calor. En el presente trabajo se evalúa el crecimiento de microorganismos heterótrofos aerobios, heterótrofos anaerobios y bacterias sulfato-reductoras sobre latón aluminio (UNS C68700, latón almirantazgo (UNS C443 y acero inoxidable AISI 316. Asimismo, se estudia la influencia del crecimiento de la bio-película sobre el comportamiento corrosivo mediante técnicas electroquímicas: curvas de polarización y espectroscopia de impedancia electroquímica. Las exposiciones se realizan en la Bahía de Montevideo, estuario del Río de la Plata

Crack propagation in stainless steel AISI 304L in Hydrogen Chemistry conditions (HWC); Propagacion de Grietas en Acero Inoxidable AISI 304L en Condiciones de Quimica de Hidrogeno (HWC)

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Fuentes C, P.; Merino C, F. [ININ, Carretera Mexico -Toluca s/n, La Marquesa, Ocoyoacac, Mexico (Mexico); Castano M, V. [Instituto de Fisica Aplicada, UNAM, Km 15.5 Carretera Queretaro-San Luis Potosi, Juriquilla, Queretaro (Mexico)]. e-mail: ads@nuclear.inin.mx

2006-07-01

Velocities of crack growth in samples type CT pre cracking of stainless steel AISI 304l solder and sensitized thermally its were obtained by the Rising Displacement method or of growing displacement. It was used a recirculation circuit that simulates the operation conditions of a BWR type reactor (temperature of 280 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu{sup +} ion. In each essay stayed a displacement velocity was constant of 1x10{sup -9} m/s, making a continuous pursuit of the advance of the crack by the electric potential drop technique. Contrary to the idea of mitigation of the crack propagation velocity by effect of the addition of the hydrogen in the system, the values of the growth velocities obtained by this methodology went similar to the opposing ones under normal operation conditions. To the finish of the rehearsal one carries out the fractographic analysis of the propagation surfaces, which showed cracks growth in trans and intergranular way, evidencing the complexity of the regulator mechanisms of the IGSCC like in mitigation conditions as the alternative Hydrogen Chemistry. (Author)

Simulación del efecto de la irradiación mediante el trabajado en frío y los tratamientos térmicos en dos aceros inoxidables austeníticos

Directory of Open Access Journals (Sweden)

de Diego, G.

1998-10-01

Full Text Available In the present study, annealed type 304 SS was cold worked and heat treated to simúlate irradiation hardening, ductility loss and grain boundary segregation. Constant Extension Rate Tensile (CERT tests were conducted to reproduce Irradiation Assisted Stress Corrosion Cracking (IASCC in BWR (Boiling Water Reactor environment.

En este trabajo se simulan los efectos que produce la irradiación, pérdida de ductilidad y segregación de impurezas en borde de grano, mediante trabajado en frío y posterior tratamiento térmico, para aceros inoxidables austeníticos AISI 304. Mediante ensayos de velocidad de extensión constante y en medios similares a los de los reactores de agua en ebullición se intenta relacionar la susceptibilidad a la corrosión bajo tensión con la susceptibilidad a la corrosión asistida por irradiación.

Estudio de la resistencia a la corrosión por picadura de aceros inoxidables austeníticos: influencia de la adición de manganeso en solución sólida

OpenAIRE

José Wilmar Calderón-Hernández; Lara Beatriz Braga Luz; Duberney Hincapie-Ladino; Neusa Alonso-Falleiros

2015-01-01

Este documento presenta los resultados de una investigación sobre la influencia del Mn en solución sólida sobre la resistencia a la corrosión por picadura de dos aceros inoxidables austeníticos, uno denominado 17Cr6Mn5Ni y un acero comercial UNS S304L utilizado como material de referencia. Fueron usadas soluciones electrolíticas de 0,6M NaCl en tres diferentes condiciones de concentración de oxígeno (solución desaireada, naturalmente aireada y aireada artificialment...

Vida a la fatiga de juntas soldadas del acero inoxidable AISI 316L obtenidas mediante el proceso GMAW

Directory of Open Access Journals (Sweden)

Puchi-Cabrera, E. S.

2007-06-01

Full Text Available An investigation has been conducted in order to determine the effect of both the metallic transfer mode (pulsed arc or short circuit and the O2 content in the Ar/O2 gas mixture, of the gas-metal arc welding process (GMAW, on the fatigue life under uniaxial conditions of welded joints of 316L stainless steel. It has been concluded that the mixture of the protective gases employed in the process could have an important influence on the fatigue life of the welded joints of such steel in two different ways. Firstly, through the modification of the radius of curvature at the joint between the welding toe and the base metal and, secondly, through a more pronounced degree of oxidation of the alloying elements induced by a higher O2 content in the mixture. As far as the metallic transfer mode is concerned, it has been determined that the welded joints obtained under a pulsed arc mode show a greater fatigue life in comparison with the joints obtained under short circuit for both gas mixtures.

Se ha llevado a cabo una investigación con la finalidad de determinar el efecto, tanto del modo de transferencia metálica (arco pulsado o cortocircuito como del contenido de O2 en la mezcla de gases protectores Ar/O2, del proceso de soldadura a tope mediante arco metálico con protección gaseosa (GMAW, sobre la vida a la fatiga en condiciones uniaxiales de juntas soldadas del acero inoxidable AISI 316L. Dicho trabajo ha permitido concluir que la composición de la mezcla de gases protectores del proceso GMAW pudiera tener una influencia importante en la vida a la fatiga de las juntas soldadas de dicho material, a través de dos formas distintas: primero, mediante la modificación del radio de curvatura entre la raíz del cordón de soldadura y el metal base y, en segundo lugar, a través del mayor grado de oxidación de los elementos de aleación. En cuanto al modo de transferencia metálica, se determinó que las juntas soldadas mediante arco pulsado

Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC); Propagacion de grietas en acero inoxidable AISI304L en condiciones de quimica de hidrogeno (HWC)

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Fuentes C, P.; Merino C, F. [ININ, 52750 Ocoyoacac, Estado de Mexico (Mexico); Castano M, V. [IFA-UNAM, Juriquilla, Queretaro (Mexico)]. e-mail: ads@nuclear.inin.mx

2006-07-01

Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu{sup ++} ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10{sup -9} m/s (3.6 {mu}m/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

Propiedades mecánicas de las uniones por láser de aceros inoxidables dúplex

Directory of Open Access Journals (Sweden)

Amigó, V.

2005-04-01

Full Text Available The welded joints of stainless steels always present problems for the microstructural modifications that occur in the heat affected zone. Particularly, duplex stainless steels present very important changes when the weld pool solidifies forming fundamentally ferritic structures with some austenite in grain boundaries. These microstructural modifications, and those which occur in the HAZ, justify the mechanical properties of the joint and mainly those of plasticity, being all of them influenced by the processing conditions. In this work the influence of the laser welding speed on the tensile behaviour of duplex stainless steel welded joints is presented. The microstructure of the obtained seams and of the heat affected zone will be evaluated by means of optic and scanning electron microscopy. Also, different microhardness profiles have been obtained to evaluate the modifications in the mechanical properties both in the seam and the zone of thermal affection.

Las uniones soldadas de aceros inoxidables siempre presentan problemas por las modificaciones microestructurales que suceden en la zona afectada por el calor. Particularmente, los aceros inoxidables dúplex presentan cambios microestructurales muy importantes al solidificar el cordón y formar estructuras, fundamentalmente ferríticas, con formación de austenita en borde de grano. Estas modificaciones microestructurales, junto a las que suceden en la ZAC, son las que justifican las propiedades mecánicas de la unión y fundamentalmente las de plasticidad. Y todo ello en función de las condiciones de procesado. En este trabajo se presenta la influencia de la velocidad de soldeo en las propiedades a tracción de uniones soldadas por láser de chapas de acero inoxidables dúplex. La microestructura de los cordones obtenidos y de la zona afectada por el calor se ha evaluado mediante microscopía óptica y electrónica de barrido, y se han obtenido diferentes perfiles de microdureza que

Corrosion behavior of powder metallurgical stainless steels in urban and marine environments

Directory of Open Access Journals (Sweden)

Bautista, A.

2006-06-01

Full Text Available This work studies the development of corrosive attack on sintered components manufactured from AISI 316L and AISI 304L powders. The stainless steels were sintered in vacuum and in nitrogen-base atmosphere at 1,120 and 1,250 ºC, and their corrosion resistance was then analyzed by electrochemical techniques and by atmospheric corrosion testing (two years at urban and marine test sites. Images are shown of the morphology of the attack on the surface of the stainless steels and the development of this attack in the interior of the material.

Este trabajo estudia el desarrollo del proceso corrosivo en componentes sinterizados fabricados a partir de polvos de AISI 316L y AISI 304L. Los aceros inoxidables fueron sinterizados en vacío y en atmósfera base nitrógeno a 1.120 y 1.250 ºC y, su resistencia a corrosión se ha analizado mediante técnicas electroquímicas y mediante ensayos de corrosión atmosférica (dos años en ambientes urbano y marino. Se muestran imágenes de la morfología del ataque en la superficie de los aceros inoxidables y del desarrollo de este ataque en el interior del material.

Influencia de la atmósfera de sinterización en las propiedades mecánicas de los aceros P/M AISI 430L

Directory of Open Access Journals (Sweden)

Iglesias, F. Javier

2014-03-01

Full Text Available It has studied the stainless steel powder metallurgy AISI 430L. It has compared the sintering in two different atmospheres; in vacuum, and in an atmosphere containing nitrogen. It has developed a heat treatment with the aim of improving the mechanical properties. This has been done through microstructural modification of complex nitrides of iron and chromium precipitates during the phase of sintering. Physical properties have been evaluated and are been performing a microstructural analysis for microstructure related to the increase in mechanical properties.Se ha estudiado el acero inoxidable pulvimetalúrgico AISI 430L, comparando la sinterización en dos atmósferas diferentes; en vacío, y en una atmósfera que contiene nitrógeno. Se ha desarrollado un tratamiento térmico con objeto de incrementar las propiedades mecánicas, mediante la modificación microestructural de los nitruros complejos de hierro y cromo precipitados durante la etapa de sinterización. Se han evaluado las propiedades físicas y a la vez se ha realizado un análisis microestructural con el fin de relacionar la microestructura con el incremento en las propiedades mecánicas.

Microstructure and mechanical properties of friction welded AISI 1040/AISI 304L steels before and after electrochemical corrosion

Energy Technology Data Exchange (ETDEWEB)

Sarsilmaz, Furkan [Firat Univ., Elazig (Turkey). Dept. of Mechatronics Engineering; Kirik, Ihsan [Batman Univ. (Turkey); Ozdemir, Niyazi [Firat Univ., Elazig (Turkey)

2018-03-01

The aim of the present study is to investigate the effect of welding parameters both on the electrochemical corrosion behavior and tensile strength of pre- and post-electrochemical corrosion of friction welded dissimilar steels. The microstructural changes of AISI 1040/AISI 304L friction welded couples and also parent materials were analyzed by using scanning electron microscopy. The electrochemical behaviors of AISI1040/AISI304L joints were comparatively investigated by potentiodynamic polarization curve test and by electrochemical impedance spectra. Moreover, tensile strength experiments were carried out determining the behavior of friction welded joints of pre- and post-electrochemical corrosion and results indicated that the maximum tensile test value of the dissimilar welded pre-electrochemical corrosion was higher than those of post-electrochemical corrosion and was also very close to AISI 1040 parent material value.

Stainless-Steel-Gadolinium Alloys; Alliages Acier Inoxydable-Gadolinium; Splavy iz nerzhaveyushchej stali i gadoliniya; Aleaciones de Acero Inoxidable-Gadolinio

Energy Technology Data Exchange (ETDEWEB)

Copeland, M.; Kato, H. [Albany Metallurgy Research Center, Bureau Of Mines, United States Department of the Interior, Albany, OR (United States)

1964-06-15

mineures ont une grande influence sur les structures resultant de traitements equilibrants et sur les possibilites de transformation des aciers. Lorsque le gadolinium est melange a de l 'acier au chrome et au nickel, deux phases mineures, Fe{sub 9}Gd et Ni{sub 7}Gd, fondent a 1080 Degree-Sign C, ce qui impose une limite superieure aux temperatures de traitement a chaud et de transformation. Les auteurs ont pu facilement transformer des alliages comprenant jusqu'a 5 Degree-Sign Io en poids de gadolinium et determiner leurs caracteristiques mecaniques et leur resistance a la corrosion. Ils n'ont observe aucun changement dans les caracteristiques mecaniques de l'acier ou sa resistance a la corrosion par l'eau chaude, lorsqu'ils lui ont ajoute'jusqu'a 3% en poids de gadolinium. En raison des limites imposees aux temperatures de transformation des aciers au chrome et au nickel par le point de fusion des phases mineures, les auteurs ont etudie les effets du gadolinium sur des aciers au chrome. Ils ont releve une seule phase mineure qui fond a 1320 Degree-Sign C en etudiant l 'isoplethe du gadolinium a 10% en poids dans l 'alliage chrome-fer-gadolinium. Cette propriete permettrait d'equilibrer et de transformer ces aciers au gadolinium aux temperatures auxquelles on opere normalement. (author) [Spanish] En vista de la excelente resistencia a la corrosion de los aceros inoxidables y del interes que presenta el gadolinio como veneno nuclear, se han estudiado aleaciones de esos dos metales. El gadolinio fue aleado con aceros inoxidables de tipo AISI-304 y al cromo, y se estudiaron las relaciones de fase, la facilidad de trabajo y las propiedades de estas aleaciones. Se observo que en las aleaciones que contienen bajos porcentajes de gadolinio, los puntos de fusion de las fases menores ejercen un efecto muy marcado sobre las estructuras resultantes de los tratamientos de equilibracion y sobre la facilidad de trabajo de los afceros. Cuando se alea el gadolinio con acerce al cromo

Physical characterization of austenitic stainless steels AISI 304 and AISI 348 L*

International Nuclear Information System (INIS)

Teodoro, Celso Antonio; Silva, Jose Eduardo Rosa da

2009-01-01

The study of radiation damages in metals and metallic alloys used as structural materials in nuclear reactors has a strategic meaning to the nuclear technology because it treats of performance of these materials in conditions that simulate the conditions of work in power reactors. Then it becomes necessary to know the essential physical properties of these materials, properties that are sensitive to the microstructural changes that occurred during the irradiation. The purpose of this work is to characterize, initially, some pre-irradiation properties of the stainless steels AISI 304 and AISI 348 L * , such as mechanical (stress-strain and microhardness) and electrical (resistivity). The AISI 348 L * has been studied for use as fuel cladding material. Both materials will be tested after irradiation in the IEA-R1 core and their properties will be compared with those in the pre-irradiated condition. The morphology of the fractured zones after tensile tests was observed using SEM (scanning electron microscopy). (author)

CATALIZADOR ESTRUCTURADO DE Pt/Al2O3 SOBRE UNA ESPUMA DE ACERO INOXIDABLE (AISI 314 PARA LA OXIDACIÓN DE CO

Directory of Open Access Journals (Sweden)

Juan P. Bortolozzi

2011-01-01

Full Text Available Se obtuvo un catalizador estructurado por recubrimiento de Pt/Al2O3 sobre las paredes de una espuma de acero inoxidable AISI 314. Para estabilizar térmicamente e incrementar la rugosidad de la superficie de la espuma original se realizó un tratamiento a 900°C por 2 h. El soporte, Al2O3, y el metal activo, Pt, se incorporaron por inmersión. Las técnicas de caracterización aplicadas, XRD, LRS y SEM-EDX, permiten concluir que el tratamiento térmico previo indujo la formación de óxido de cromo y de las espinelas Mn1+xCr2-xO4-x y FeCr2O4 como fases principales en las paredes del sustrato. El espesor de la capa formada es cercano a 1 μm y los cristales producidos tienen forma octaédrica. El cubrimiento de alúmina presentó en general una apariencia homogénea, sin interacción con los óxidos formados durante el tratamiento. El Pt se distribuyó de manera uniforme, resultando un catalizador muy activo para la reacción test elegida: oxidación de monóxido de carbono.

Preparation of high-performance ultrafine-grained AISI 304L stainless steel under high temperature and pressure

Directory of Open Access Journals (Sweden)

Peng Wang

2016-08-01

Full Text Available Bulk ultra-fine grained (UFG AISI 304L stainless steel with excellent mechanical properties was prepared by a high-temperature and high-pressure (HTHP method using nanocrystalline AISI 304L stainless steel powders obtained from ball milling. Samples were sintered in high-pressure conditions using the highest martensite content of AISI 304L stainless steel powders milled for 25 h. Analyses of phase composition and grain size were accomplished by X-ray diffraction and Rietveld refinement. By comparing the reverse martensite transformation under vacuum and HTHP treat, we consider that pressure can effectively promote the change in the process of transformation. Compared with the solid-solution-treated 304L, the hardness and yield strength of the samples sintered under HTHP are considerably higher. This method of preparation of UFG bulk stainless steel may be widely popularised and used to obtain UFG metallic materials with good comprehensive performance.

Intergranular stress corrosion in soldered joints of stainless steel 304.; Corrosion intergranular bajo esfuerzo en uniones soldadas de acero inoxidable 304

Energy Technology Data Exchange (ETDEWEB)

Zamora R, L [Instituto Nacional de Investigaciones Nucleares, Mexico City (Mexico)

1994-12-31

The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author).

Relaciones cuantitativas entre los contenidos de azufre y de sulfuros en los aceros inoxidables tipo AISI 303: influencia de la composición química de los sulfuros

Directory of Open Access Journals (Sweden)

Botella, J.

1999-06-01

Full Text Available The work has been done with ten AISI 303 stainless steel rods which have similar chemical compositions, except for sulphur which varies between 0.25 and 0.36%. These steels are studied by Scanning Electron Microscopy (SEM and Energy Dispersive X-Ray Spectrometry (EDX. The sulphides are chemically microanalysed and the occupied volume determined by automatic image analysis. It can be inferred that the chemical composition of sulphides in AISI 303 steels is variable to some extent even though the steel chemistry is almost invariable. This could mean that solidification conditions and thermomechanical transformations are able to affect resulting in variations of sulphide compositions. Quantitative relations between sulphur and sulphide contents are established and the influence of sulphide chemical compositions on those relations is studied. The experimental results are compared with those obtained from theoretical calculations. A good approach is obtained when the difference between chemical compositions of real sulphides and the theoretical one, MnS, is taken into account.

Se trabaja con una serie de diez redondos de aceros inoxidables tipo AISI 303 de composiciones químicas prácticamente iguales a excepción del azufre que varía entre 0,25 y 0,36%. Se examinan los aceros mediante Microscopía Electrónica de Barrido (MEB y Espectrometría de Dispersión de Energías de Rayos X (EDX acoplada al MEB, analizándose químicamente los sulfuros y determinando, mediante análisis automático de imágenes, los volúmenes ocupados por los sulfuros. Parece deducible que la composición química de los sulfuros en el AISI 303 puede ser discretamente variable aún siendo prácticamente invariable la composición química del acero. Ello podría significar que las condiciones de solidificación y las transformaciones termomecánicas pueden influir, dando como resultado variaciones en la composición química de los sulfuros. Se establecen

Soldadura de recargue con aceros inoxidables dúplex

OpenAIRE

Zappa, Sebastián; Martínez, Juan; Svoboda, Hernán Gabriel; Surian, Estela

2016-01-01

Los aceros inoxidables dúplex se caracterizan por poseer una estructura dual constituida por ferrita y austenita en iguales proporciones. Poseen una combinación de buenas propiedades mecánicas y resistencia a la corrosión, que dependen de la composición química y de la relación entre las fases mencionadas. Son ampliamente utilizados en las industrias de procesos químicos y, fundamentalmente, del petróleo y gas. La soldadura de recargue, es utilizada en las industrias de fabricación y reparaci...

Resistência à corrosão de junta dissimilar soldada pelo processo TIG composta pelos aços inoxidáveis AISI 316L e AISI 444

Directory of Open Access Journals (Sweden)

Luis Henrique Guilherme

2014-03-01

Full Text Available O aço inoxidável AISI 444 tornou-se uma opção para substituir a liga AISI 316L devido ao seu menor custo e satisfatória resistência à corrosão. Entretanto, o uso da liga AISI 444 no feixe tubular de trocadores de calor acarreta na soldagem de uma junta dissimilar. O presente estudo teve por objetivo avaliar a resistência à corrosão da junta tubo-espelho soldada pelo processo TIG composta pelas ligas AISI 316L e AISI 444. A manufatura das amostras consistiu em replicar o projeto da junta tubo-espelho de trocadores de calor. Realizou-se em juntas soldadas ensaios de sensitização, perda de massa por imersão desde a temperatura ambiente até 90 ºC, e ensaios eletroquímicos de polarização potenciodinâmica nos eletrólitos 0,5 mol/L de HCl e 0,5 mol/L de H2SO4. Os resultados mostraram que a junta dissimilar sofreu corrosão galvânica com maior degradação na zona afetada pelo calor (ZAC do tubo AISI 444. Porém, os mecanismos de corrosão localizada (pite e intergranular demonstraram ser mais ativos para a liga AISI 316L. Conclui-se que a junta dissimilar apresentou melhor resistência à corrosão do que a junta soldada composta unicamente pela liga AISI 316L em temperaturas de até 70 ºC, conforme as condições observadas neste trabalho.

Applications of the essay at slow deformation velocity in pipes of stainless steel AISI-304; Aplicaciones del ensayo a velocidad de deformacion lenta en tuberias de acero inoxidable AISI-304

Energy Technology Data Exchange (ETDEWEB)

Zamora R, L.; Mora R, T. De la [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2004-07-01

Nowadays is carried out research related with the degradation mechanisms of structures, systems and/or components in the nuclear power plants, since many of the involved processes are those responsible for the dependability of these, of the integrity of the components and of the aspects of safety. The purpose of this work, was to determine the grade of susceptibility to the corrosion of a pipe of Austenitic stainless steel AISI 304, in a solution of Na CI (3.5%) to the temperatures of 60 and 90 C, in two different thermal treatments - 1. - Sensitive 650 C by 4 hours and cooled in water. 2. Solubilized to 1050 C by 1 hour and cooled in water.

Caracterización mecánica de recubrimientos de aluminio por CVD-FBR sobre aceros inoxidables y resistencia a la oxidación en vapor de agua

OpenAIRE

Diego Pérez-Muñoz; José Luddey Marulanda-Arévalo; Juan Manuel Meza-Meza

2015-01-01

Los recubrimientos de aluminio depositados sobre el acero inoxidable austenítico AISI 317 por Deposición Química de Vapor en Lecho Fluidizado (CVD-FBR) presentan a altas temperaturas una reducción de la velocidad de corrosión de más de 80 veces. Se realizó la caracterización mecánica de los recubrimientos por medio de microdureza, nanoindentación, para conocer cómo se vieron afectas las propiedades mecánicas (en especial la dureza y el módulo de Young) del recubrimiento y del sustrato luego d...

Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor; Caracterizacion de soldaduras de acero inoxidable AISI 304L similares a las de la envolvente del nucleo de un reactor BWR

Energy Technology Data Exchange (ETDEWEB)

Gachuz M, M.E.; Palacios P, F.; Robles P, E.F. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

2003-07-01

Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J{sub IC}) to ambient temperature for the base metal of 528 KJ/m{sup 2}, which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

Desarrollo de los procesos de moldeo por inyección y extrusión de polvos para la obtención de piezas de aceros inoxidables dúplex y ferríticos

OpenAIRE

Sotomayor Lozano, María Eugenia

2011-01-01

En la presente Tesis Doctoral se ha desarrollado el proceso de moldeo por inyección de polvos (pIM) para la obtención de piezas de acero inoxidable dúplex con aplicaciones en ortodoncia. Por otro lado, se ha desarrollado el proceso de moldeo por extrusión de polvos (PEM) para la obtención de láminas y tubos porosos de acero inoxidable ferrítico con aplicaciones en pilas de combustible de óxido sólido (SOFCs). En primer lugar, se prepararon y caracterizaron térmica y reológicamente las mezclas...

Influencia de la microestructura en el comportamiento a fatiga de aceros inoxidables austeníticos con alto contenido en molibdeno

Directory of Open Access Journals (Sweden)

Oñoro, J.

2006-02-01

Full Text Available Austenitic stainless steels with molybdenum present high mechanical properties and corrosion resistance to aggressive environments. These steels have been used to tank and vessel components for high corrosive liquids as phosphoric, nitric and sulphuric acids. These materials with low carbon and nitrogen addition have been proposed candidates as structural materials for the international thermonuclear experimental reactor (ITER in-vessel components. Molybdenum addition in austenitic stainless steel improves mechanical and corrosion properties, but with it can produce the presence of nitrogen microstructure modifications by presence or precipitation of second phases. This paper summarises the fatigue and corrosion fatigue behaviour of two 317LN stainless steels with different microstructure. Fully austenitic steel microstructure show better fatigue, corrosion fatigue resistance and better ductility than austenitic steel with delta ferrite microstructure, mainly at low stresses.

Los aceros inoxidables austeníticos con elevados contenidos en molibdeno presentan alta resistencia mecánica y resistencia a los medios corrosivos. Se utilizan en la construcción de depósitos y recipientes para el almacenamiento y transporte de líquidos altamente corrosivos, tales como ácido fosfórico, nítrico o sulfúrico. Estos materiales con bajo carbono y adiciones de nitrógeno han sido propuestos como candidatos para materiales estructurales en la fabricación de la vasija del reactor experimental termonuclear internacional (ITER. La adición de molibdeno mejora las propiedades frente a la corrosión de los aceros inoxidables austeníticos. Sin embargo, este aumento del contenido en molibdeno, junto con la presencia de nitrógeno, puede producir modificaciones microestructurales, por la aparición de fases precipitadas o segundas fases. En este trabajo, se analiza el comportamiento la fatiga y corrosión-fatiga de dos aceros inoxidables austen

Reassessment of the swelling behavior of AISI 304 stainless steel

International Nuclear Information System (INIS)

Garner, F.A.; Porter, D.L.

1982-03-01

Published swelling data derived from EBR-II irradiations of AISI 304 and 304L have been reanalyzed in light of insights gained from irradiation of AISI 316 and Fe-15Cr-25Ni. The primary influence of temperature, displacement rate and compositional variations in the 300 series stainless steels lies in the duration of the transient regime of swelling and not in the steady-state or constant swelling rate regime

“MEDICION DE PARAMETROS GENERADORES DE ESFUERZOS RESIDUALES DURANTE EL PROCESO DE SOLDADURA DE ACERO INOXIDABLE AUSTENITICO AISI 304L”.

OpenAIRE

García López, Christian Jesus

2012-01-01

En la actualidad los procesos de soldadura por arco eléctrico se han convertido en la técnica por excelencia para la unión del acero y sus aleaciones. Se puede mencionar que la importancia de la soldadura, es tal, que sin ella no serían posibles muchos de los productos y servicios que cotidianamente son consumidos o requeridos por las sociedades contemporáneas actuales. Cada vez con mayor longitud y diámetro se instalan líneas de tubería para la distribución y conducción de tod...

Efecto de la velocidad y ángulo de impacto en la resistencia a corrosión - erosión de aceros inoxidables recubiertos con TiN

Directory of Open Access Journals (Sweden)

José Ricardo Cano Rodas

2004-01-01

Full Text Available Fueron estudiados los mecanismos de degradación superficial en aceros inoxidables austenítico AISI 304 y martensítico AISI 420, con y sin recubrimiento cerámico de TiN, aplicado mediante técnica de deposición física de vapor PVD por arco pulsado, sometidos a erosión (solución de agua destilada con 30% en peso de partículas de sílice, corrosión (solución ½ M H2SO4 + 3.5% NaCl y efectos sinérgicos corrosión - erosión. Fue construido un dispositivo para realizar los ensayos descritos con la posibilidad de variar la velocidad y el ángulo medio de impacto de las partículas sobre la superficie de las muestras. Marcas características fueron observadas en las superficies desgastadas, siendo la condición de ángulo rasante la de mayor efecto nocivo tanto para las superficies desnudas como para las recubiertas con TiN. El nivel de deterioro superficial aumentó con la velocidad de impacto, al tiempo que se evidenció la importancia de la adherencia de las películas protectoras al substrato para la obtención de una buena resistencia a corrosiónerosión. La sinergia corrosión-erosión presentó, en algunas ocasiones, un efecto positivo para la superficie, ya que el impacto de las partículas duras causó intensa deformación plástica pero no consiguió remover material de la superficie.

Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65; Estudio comparativo de la corrosion inducida por microorganismos sulfatorreductores, en un acero inoxidable 304L sensibilizado y un acero al carbono API X65

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)]. e-mail: ads@nuclear.inin.mx

2004-07-01

In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

Recubrimientos de aluminio-silicio realizados por deposición química de vapor en lecho fluidizado sobre el acero inoxidable AISI 316

Directory of Open Access Journals (Sweden)

José Luddey Marulanda Arevalo

2013-12-01

Full Text Available Los recubrimientos de aluminio-silicio fueron depositados sobre el acero inoxidable AISI 316 mediante deposición química de vapor en lecho fluidizado (CVD-FBR, en el rango de temperaturas de 540 a 560 ºC, utilizando un lecho formado por 2,5 g de silicio y 7,5 g de aluminio en polvo, y 90 g de lecho inerte (Alúmina, el cual se hizo fluidizar con Ar. Como gases activadores se usó una mezcla de HCl/H2, en relaciones de 1/10 a 1/16. Además, se varió el tiempo de deposición de los recubrimientos de 45 minutos a 1.5 horas, con una relación en volumen de 50% de gases activos y 50% de gases neutros. Se realizó una simulación termodinámica con la ayuda del programa informático Thermocalc, para obtener información de la posible composición y cantidad de material depositado, para las condiciones seleccionadas. En los recubrimientos se encuentran FeAl2Si, Fe2Al5 y FeAl2. Los recubrimientos aluminio-silicio fueron tratados térmicamente, para mejorar sus propiedades mecánicas y su comportamiento frente a la oxidación, por la interdifusión de los elementos de aleación, ya que el tratamiento térmico hace que el aluminio difunda hacia el substrato, y el hierro difunda hacia la superficie del recubrimiento, logrando la transformación de los compuestos anteriores en FeAl, Al2FeSi, Cr3Si, AlCrFe y AlFeNi.

Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

Directory of Open Access Journals (Sweden)

Jose L. Marulanda

2014-01-01

Full Text Available Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de los substratos para conocer las posibles fases sólidas y gaseosas que se podrían formar, en presencia de una ambiente con 100% vapor de agua y una atmosfera de presión. La forma de ataque a 750 ºC es similar a 700 ºC, aunque la velocidad de oxidación es mayor, ya que la difusión de los elementos de aleación y las reacciones de oxidación son más rápidas. Los recubrimientos de aluminio tienen una buena resistencia a la oxidación en vapor de agua, ya que forman una capa superficial de Al 2 O 3 , que es compacta y adherente, la cual protege al substrato del ataque corrosivo.

Comparative study of high temperature oxidation behaviour in AISI 304 and AISI 439 stainless steels

Directory of Open Access Journals (Sweden)

Antônio Claret Soares Sabioni

2003-06-01

Full Text Available This work deals with a comparison of high temperature oxidation behaviour in AISI 304 austenitic and AISI 439 ferritic stainless steels. The oxidation experiments were performed between 850 and 950 °C, in oxygen and Ar (100 vpm H2. In most cases, it was formed a Cr2O3 protective scale, whose growth kinetics follows a parabolic law. The exception was for the the AISI 304 steel, at 950 °C, in oxygen atmosphere, which forms an iron oxide external layer. The oxidation resistance of the AISI 439 does not depend on the atmosphere. The AISI 304 has the same oxidation resistance in both atmospheres, at 850 °C, but at higher temperatures, its oxidation rate strongly increases in oxygen atmosphere. Concerning the performance of these steels under oxidation, our results show that the AISI 439 steel has higher oxidation resistance in oxidizing atmosphere, above 850 °C, while, in low pO2 atmosphere, the AISI 304 steel has higher oxidation resistance than the AISI 439, in all the temperature range investigated.

El refractario en la fabricación de acero inoxidable

Directory of Open Access Journals (Sweden)

Ferrer, F. J.

2006-10-01

Full Text Available The influence of the steelmaking process on the quality and the performance of refractory materials used on stainless steel production was described. The most important technical and design parameters of the processing units were explained and related with the slag chemical composition and the qualities of the refractories used.

Se describe la influencia del proceso siderúrgico sobre el tipo y rendimiento del material refractario utilizado en la producción de acero inoxidable. Tras describir las distintas unidades implicadas en el proceso metalúrgico se hace especial énfasis en la importancia que ejercen el diseño de las distintas unidades y el tipo y control de la escoria sobre la calidad del tipo de refractario a utilizar.

Swelling of AISI 304L in response to simultaneous variations in stress and displacement rate

International Nuclear Information System (INIS)

Porter, D.L.; Garner, F.A.

1984-01-01

The duration of the transient regime of neutron-induced swelling in annealed AISI 304L at 400 0 C is sensitive to both stress and displacement rate variations. The simultaneous application of both variables exerts a synergistic effect on the transient regime. The duration of this regime cannot be reduced below a required intrinsic exposure of approx. 10 dpa, however, which has been found to be characteristic of all Fe-Ni-Cr austenitic alloys. This is four times larger than that currently assumed in the stress-affected swelling equation for 20% cold-worked AISI 316

Behaviour under fatigue of AISI 304-L stainless steel welded joints

International Nuclear Information System (INIS)

Scal, M.W.; Joia, C.J.B.M.; Sousa e Silva, A.S. de

1979-01-01

The fatigue behaviour at room temperature of AISI-304-L stainless steel welded joints obtained by two distinct welding methods was studied. The results obtained were compared to those characteristic of the base metal. The welded joint fatigue samples were rectified in order to eliminate the effect of the welded seam geometry. It was concluded that the mechanisms of fatigue crack start in this case is commanded by the austenitic matrix, there being no influence of the delta ferrite rate and distribution present at the melted zone. (Author) [pt

Fatigue of welded joint in a stainless steel AISI 304 L

International Nuclear Information System (INIS)

Kuromoto, N.K.; Guimaraes, A.S.; Miranda, P.E.V. de

1986-01-01

The flexion fatigue behavior for the base metal and welded joint of an AISI 304 L stainless steel type, used in the Angra-1 reactor, was determined. An automatic welding process was used with improved procedures in order to assure better welding metallurgy. Fatigue tests samples reinforcements were done to allow the evaluation of metallurgical variables, specially the role played by delta ferrite. The resulting welded joint showed better fatigue life than the base metal. Delta ferrite was found to play an important role on the initiation and propagation processes of the fatigue cracks. (Author) [pt

Evaluation of structural behaviour and corrosion resistant of austenitic AISI 304 and duplex AISI 2304 stainless steel reinforcements embedded in ordinary Portland cement mortars; Evaluacion del comportamiento estructural y de resistencia a la corrosion de armaduras de acero inoxidable austenitico AISI 304 y duplex AISI 2304 embebidas en morteros de cemento Portland

Energy Technology Data Exchange (ETDEWEB)

Medina, E.; Cobo, A.; Bastidas, D. M.

2012-07-01

The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304) and duplex EN 1.4362 (AISI 2304) have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR), of reinforcements embedded in ordinary Portland cement (OPC) mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure. (Author) 26 refs.

Oxidación cíclica de un acero refractario AISI 310 a alta temperatura en atmósferas con contenidos de oxígeno variables

Directory of Open Access Journals (Sweden)

Higuera-Hidalgo, V.

2005-06-01

Full Text Available High temperature oxidation tests of an AISI 310 stainless steel was performed in two different environments: in an standard atmosphere (21 % oxygen at 704, 800, 884 and 1,000 °C and in the typical environment of a gas turbine and vapor generator of a combined-cycle electric generation unit (10 % oxygen at 800 and 1,000 °C. The oxidation kinetics was determined by means of the measurement of the weight gain per unit surface of the specimen and also determining the thickness of the oxide layer. Comparable results have been obtained using both methodologies and the effect of the oxygen content along with the other experimental differences were determined observing the oxidation kinetics in both environments. The cyclic oxidation of AISI 310 deteriorates at temperatures higher than 1,000 °C.

Se ha llevado a cabo un estudio experimental sobre la oxidación a altas temperaturas de un acero inoxidable refractario AISI 310, en dos ambientes diferentes: en una atmósfera convencional (21 % de O₂, a 704, 800, 884 y 1.000 °C y en un ambiente simulativo de una turbina de gas y del generador de vapor de uña central eléctrica de ciclo combinado (10-11 % de O₂, a 800 y 1.000 °C. La cinética de la oxidación del material se ha determinado a partir, tanto de la ganancia de peso por unidad de superficie experimentada por las probetas objeto de ensayo como por la determinación de los espesores de las capas de óxido formados. Se han obtenido resultados comparables con ambas metodologías y se ha puesto de manifiesto el efecto del contenido de oxígeno y de las demás diferencias experimentales a partir de la comparación de las cinéticas de oxidación del acero en los dos medios oxidantes analizados. La oxidación del acero AISI 310 en situaciones térmicas cíclicas empieza ya a ser importante a partir de una temperatura de 1.000 °C.

Evaluación de la fuerza de doblado y de fricción en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embutición

Directory of Open Access Journals (Sweden)

Coello, J.

2012-08-01

Full Text Available Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values.

El radio de entrada a la matriz se considera una de las zonas críticas en los procesos de conformado de chapa mediante embutición profunda. El análisis de la fuerza de fricción y de doblado existentes resulta importante para predecir el comportamiento de la chapa en dicha zona, así como para garantizar una lubricación adecuada a las condiciones de procesado. En el presente trabajo, se aplica un método de ensayo que evalúa las acciones en el proceso de doblado del acero AISI 304 DDQ bajo condiciones similares a las que sufre el material en los procesos de embutición y que no son reproducidas por los clásicos ensayos de doblado bajo tensión. Se establecen como variables la deformación experimentada previamente por el material en condiciones típicas de cortante puro, “pure shear”, el ángulo de doblado y el radio de doblado. Los resultados obtenidos

Desarrollo de un modelo matemático de diferencias finitas para el análisis del campo de temperaturas en la soldadura por arco de chapas finas de acero inoxidable

Directory of Open Access Journals (Sweden)

Miguel, V.

2010-12-01

Full Text Available This work develops a finite difference method to evaluate the temperature field in the heat affected zone in butt welding applied to AISI 304 stainless steel thin sheet by GTAWprocess. A computer program has been developed and implemented by Visual Basic for Applications (VBA in MS-Excel spreadsheet. The results that are obtained using the numerical application foresee the thermal behaviour of arc welding processes. An experimental methodology has been developed to validate the mathematical model that allows to measure the temperature in several points close to the weld bead. The methodology is applied to a stainless steel sheet with a thickness lower than 3 mm, although may be used for other steels and welding processes as MIG/MAG and SMAW. The data which has been obtained from the experimental procedure have been used to validate the results that have been calculated by the finite differences numerical method. The mathematical model adjustment has been carried out taking into account the experimental results. The differences found between the experimental and theoretical approaches are due to the convection and radiation heat losses, which have not been considered in the simulation model.With this simple model, the designer will be able to calculate the thermal cycles that take place in the process as well as to predict the temperature field in the proximity of the weld bead.

En este trabajo se desarrolla un método de diferencias finitas para calcular el campo de temperaturas en la zona afectada por el calor en la soldadura de dos chapas de acero inoxidable AISI 304, soldadas mediante el procedimiento GTAW. Se ha desarrollado un programa informático implementado en libros de cálculo MS-Excel con Visual Basic para Aplicaciones (VBA. Los experimentos modelizados a través de la aplicación numérica predicen el comportamiento térmico de un procedimiento de soldadura. Para la validación del modelo matemático se ha desarrollado un

Influencia de la soldadura sobre la rotura por tensiones en tubos de acero inoxidable austenitico del tipo 18-11NB(TP347

Directory of Open Access Journals (Sweden)

Gutiérrez de Saiz-Solabarria, S.

2000-06-01

Full Text Available This work has been undertaken to study the stress cracking failure in various 18Cr11Ni [TP347 (18-11Nb, TP 321 (18-11 Ti, TP304 (18-11 and TP316 (18-11-2] types austenitic stainless steel tubes. The material used was produced hot-rolling at 76,2 mm φ (3"φ x 2,54 mm (1/10" thickness. The study was carried out at 593ºC and applied stress of 50 Ton/in2.

Se estudia el efecto de la soldadura sobre la rotura por tensiones en tubos de acero inoxidable austenítico estabilizado con Nb o Ti de los tipos 18-11Nb (TP 347 y 18-11Ti (TP 321 así como sin estabilizar del tipo 18-11 (TP 304 y con Mo del tipo 18-11-2 (TP 316. Los tubos, en todos los casos, son de dimensiones 76,2 mm (3” φ x 2,54 mm (1/10” de espesor y la tensión aplicada (σ de 10 Ton/in2, para una temperatura de servicio de 593ºC.

Predicción del desgaste del flanco de la herramienta de corte durante el torneado en seco de alta velocidad para piezas de acero AISI 316L en la industria minera

Directory of Open Access Journals (Sweden)

Yusimit K. Zamora-Hernández

2015-07-01

Full Text Available Se realizó un estudio experimental sobre la influencia de los parámetros de corte en el torneado del acero inoxidable AISI 316L con insertos recubiertos de TiCN, Al2O3, TiN. Un microscopio electrónico de barrido fue utilizado para medir y analizar el desgaste de las herramientas de corte. Los resultados fueron comparados utilizando el análisis de varianza y el análisis de regresión múltiple para describir la relación entre el desgaste del flanco de las herramientas de corte, el tiempo de maquinado y el avance de corte, obteniéndose las ecuaciones de los modelos ajustados. La investigación demostró el efecto significativo del avance y del tiempo de maquinado en el desgaste del flanco. El inserto de tres capas no sobrepasó el criterio de fin de vida del desgaste, mientras que el inserto de una capa sufrió un desgaste elevado para la mayor velocidad de corte. El desgaste del flanco tuvo mejor comportamiento para el avance de 0,08 mm/rev en todas las velocidades empleadas en este estudio. Los errores medios absolutos no superaron el 15 %.

Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex

Directory of Open Access Journals (Sweden)

Sebastián Zappa

Full Text Available Resumen Los aceros inoxidables dúplex poseen una microestructura dual (ferrita y austenita con contenidos aproximadamente iguales y se caracterizan por tener buena soldabilidad, buenas propiedades mecánicas y una alta resistencia a la corrosión generalizada y localizada. Gracias a estas características, estos aceros son los principales materiales a emplear en cañerías con altas exigencias, ampliamente utilizados en varias industrias, principalmente la petroquímica. Dichas propiedades están controladas por la composición química, el equilibrio microestructural y la ausencia de compuestos intermetálicos. El objetivo de este trabajo fue estudiar la influencia de la composición química del metal de aporte y el calor aportado sobre la microestructura y las propiedades mecánicas en juntas soldadas de cañerías de acero inoxidable dúplex. El metal base utilizado fue un acero inoxidable dúplex UNS S31803 de 8” de diámetro y 8,18 mm de espesor y los metales de aporte fueron dos alambres tubulares que depositan aceros inoxidables dúplex y lean dúplex (AWS A5.22: E2209T1-1 y E2209T1-G, mediante el proceso de soldadura semi-automático bajo protección gaseosa, soldados con alto y bajo calor aportado. De cada probeta se extrajeron muestras donde se determinó la composición química, se realizó la caracterización microestructural y se determinaron las propiedades mecánicas (dureza, tracción y Charpy-V.

Corrosión a alta temperatura de acero al carbono y acero inoxidable austenítico en atmósferas contaminadas por CO2

OpenAIRE

Proy Pérez, Manuel

2014-01-01

Los efectos a veces catastróficos producidos por los procesos de corrosión a alta temperatura en atmósferas contaminadas por agentes agresivos, poseen la suficiente relevancia para ser objeto de estudio en los próximos años, debido a que en muchas ocasiones no están definidos claramente. Los aceros al carbono y los inoxidables austeníticos son materiales potencialmente utilizables en condiciones de elevada temperatura gracias a su excelente relación entre sus propiedades est...

Martensitic Transformation in Ultrafine-Grained Stainless Steel AISI 304L Under Monotonic and Cyclic Loading

Directory of Open Access Journals (Sweden)

Heinz Werner Höppel

2012-02-01

Full Text Available The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation behavior is similar to the coarse-grained condition, but the cyclic stress response is three times larger for the ultrafine-grained condition.

Ductility in a new low nickel stainless steel for reinforced concrete

Directory of Open Access Journals (Sweden)

Cobo, A.

2011-12-01

Full Text Available This paper discusses the stress-strain curves for a new low nickel stainless steel, a conventional AISI 304 stainless steel and a carbon steel commonly used in reinforced concrete structures. Ductility was studied in terms of ultimate tensile strength (f_max, elastic limit (f_y and total elongation at maximum force [ultimate strain; uniform elongation] (ε_max. The three materials were assessed with internationally accepted criteria, such as plastic rotational capacity, necking region and the toughness index (total energy absorbed at uniform elongation. The findings were compared to the properties of three types of conventional reinforcing steel: 500SD, 500N and 500H (EC-2.

En este trabajo se presentan los diagramas tensióndeformación de un nuevo acero inoxidable con bajo contenido en níquel, un inoxidable convencional AISI 304 y un acero al carbono de uso común en estructuras de hormigón armado. Dicha ductilidad se ha estudiado determinando la tensión máxima (f_max, la tensión en el límite elástico (f_y y la deformación bajo carga máxima (ε_max. Los tres materiales se han evaluado utilizando criterios aceptados internacionalmente, como son el índice p (capacidad de rotación plástica, el índice A* (área plástica de endurecimiento y el índice de tenacidad I_d (energía total absorbida en el punto de alargamiento bajo carga máxima, los resultados obtenidos se han comparado con los aceros convencionales de armaduras 500SD, 500N y 500H (EC-2.

Dependence of corrosion properties of AISI 304L stainless steel on the austenite grain size

Energy Technology Data Exchange (ETDEWEB)

Sabooni, Soheil; Rashtchi, Hamed; Eslami, Abdoulmajid; Karimzadeh, Fathallah; Enayati, Mohammad Hossein; Raeissi, Keyvan; Imani, Reihane Faghih [Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of). Dept. of Materials Engineering; Ngan, Alfonso Hing Wan [The Univ. of Hong Kong (China). Dept. of Mechanical Engineering

2017-07-15

The corrosion resistance of austenitic stainless steels is known to be hampered by the loss of chromium available for passive surface layer formation as a result of chromium carbide precipitation at austenite grain boundaries during annealing treatments. Although high-temperature annealing can promote carbide dissolution leading to better corrosion resistance, grain coarsening also results, which would lead to poorer mechanical properties. Processing methods to achieve both good corrosion resistance and mechanical properties are thus highly desirable for austenitic stainless steels. In the present study, we show that the corrosion resistance of AISI 304L stainless steel can be improved by grain refinement into the ultrafine-grained regime. Specifically, samples with different austenite grain sizes in the range of 0.65-12 μm were studied by potentiodynamic polarization and electrochemical impedance spectroscopy tests in a 3.5 wt.% NaCl solution. All samples showed a typical passive behavior with similar corrosion potential, but the corrosion current density decreased significantly with decreasing grain size. The results show that the sample with the finest grain size had the best corrosion resistance due to a higher resistance of the passive layer to pitting attacks. This study indicates that grain refinement which improves mechanical properties can also significantly improve the corrosion resistance of AISI 304L stainless steel.

Estudio in vitro de la citotoxicidad y genotoxicidad de los productos liberados del acero inoxidable 316L con recubrimientos cerámicos bioactivos Cytotoxic and genotoxic study of in Vitro released products of stainless Steel 316l with bioactive ceramic Coatings

Directory of Open Access Journals (Sweden)

María Elena Márquez Fernández

2007-03-01

Full Text Available El acero inoxidable AISI 316L es el biomaterial mas utilizado para la fabricación de implantes temporales, pero presenta limitaciones para implantes permanentes debido a la liberación de iones metálicos hacia los tejidos circundantes, produciendo especies reactivas de oxígeno (ERO y daño en ADN, factores que aumentan el riesgo de aparición de tumores locales y fallas mecánicas del implante. Una estrategia utilizada para disminuir la liberación de iones es la modificación superficial de los implantes metálicos por medio de recubrimientos inorgánicos, cerámicos o vítreos, aplicados por el método sol-gel, el cual presenta una serie de ventajas comparativas con otras técnicas de deposición, como buena adherencia, aplicación sencilla, mínimos problemas de secado, bajas temperaturas de densificación y posibilidad de agregar partículas y/o grupos orgánicos que mejoran la adherencia celular al implante aumentando su biocompatibilidad. En el presente trabajo se evaluaron los efectos citotóxico por medio de la técnica MTT, y genotóxico por electroforesis en gel de células individuales (Ensayo Cometa, sobre células de la línea celular CHO, de los productos liberados en medio MEM por el acero inoxidable 316L sin recubrir, recubierto con una monocapa de vidrio de sílice (MC, o con doble capa que contiene partículas bioactivas de hidroxiapatita (HA, vidrio (V o vitrocerámico (VC, después de un periodo de 30 días. Los resultados muestran que a los 30 días de envejecimiento en medio MEM no se encuentra ningún efecto citotóxico, pero se encontró efecto genotóxico en las probetas de A y MC que no representa un peligro inminente a sistemas celulares. The stainless steel AISI 316L is the must used biomaterial for the making of temporal prosthesis, but it presents severe limitations for permanent implants due to the generation and migration of metallic ions to the surrounding peripheral tissues, which produces oxygen reactive

Analysis of AISI 304 Tensile Strength as an Anchor Chain of Mooring System

Science.gov (United States)

Hamidah, I.; Wati, R.; Hamdani, R. A.

2018-05-01

The background of this research is the use of mild steel (i.e., St37) as anchor chain that works on the corrosive environment of seawater which is possible to decrease its tensile strength. The longer soaked in seawater, the more significant the lowering of its tensile strength. Anchor chain needs to be designed by considering its tensile strength and corrosion resistance, so it’s able to support mooring system well. The primary purpose of this research is obtaining the decreasing of stainless steel 304 (AISI 304) tensile strength which is corroded by seawater as anchor chain of the mooring system. It is also essential to obtain the lifetime of AISI304 and St37 as anchor chain with the same load, the corrosion rate of AISI 304, and St 37 in seawater. The method which was employed in this research is an experiment with four pieces of stainless steel AISI 304, and of St 37 corrosion testing samples, six pieces of stainless steel 304, and six pieces of St 37 for tensile testing samples. The result of this research shows that seawater caused stainless steel AISI 304 as anchor chain has decreased of tensile strength about 1.68 % during four weeks. Also, it indicates that AISI 304 as anchor chain has a lifetime about 130 times longer than St 37. Further, we found that the corrosion rate of stainless steel 304 in seawater is 0.2042 mpy in outstanding category, while the St 37 samples reached up to 27.0247 mpy ranked as fair category. This result recommends that AISI 304 more excellence than St 37 as anchor chain of the mooring system.

Evaluación de diferentes aceros para la evolución de hidrógeno en KOH

Directory of Open Access Journals (Sweden)

Falk Michel Julke

2014-05-01

Full Text Available Se estudió el comportamiento electroquímico de los diferentes tipos de aceros comerciales de bajo costo (A36, 430 y 304 como electrodos para la obtención de hidrógeno. El propósito de este trabajo fue estudiar la evolución de hidrógeno, para lo cual se utilizaron técnicas electroquímicas como cronoamperometría y curvas voltamperométricas, en diferentes concentraciones de KOH (5% y 25% m/m. El acero inoxidable 304 en una concentración de 25%m/m tuvo el mejor desempeño, pues en estas condiciones el inicio de liberación de hidrógeno disminuyó y presentó el menor requerimiento de potencial para su uso como placa bipolar.

Comportamiento del acero de baja aleación SA-508 y del acero al carbono A-410b en las condiciones de operación y parada del circuito primario de los reactores de agua ligera tipo PWR

Directory of Open Access Journals (Sweden)

García-Redondo, María del Sol

2000-04-01

Full Text Available The corrosion rate of low alloy steel SA-508 and carbon steel A-410b in simulated operation and shutdown conditions of pressurized water reactor has been determined. Moreover potentiodynamic polarization curves and galvanic effect through coupling of AISI-304 have been carried out under shutdown simulated condition.

En este trabajo se ha determinado la cinética de corrosión del acero de baja aleación SA-508 y del acero al carbono A-410b en condiciones que simulan la operación y la parada de los reactores de agua ligera a presión. También se han realizado curvas de polarización potenciodinámica y se ha estudiado el acoplamiento galvánico con AISI-304 en condiciones de parada de los reactores de agua ligera a presión.

Análisis de la resistencia a la corrosión de barras corrugadas de acero inoxidable en medios acuosos que simulan el hormigón

Directory of Open Access Journals (Sweden)

Belzunce, F. J.

2004-04-01

Full Text Available The corrosion behaviour of stainless steel reinforced bars used in civil engineering was studied. Different electrochemical tests were performed using several stainless steel bars (austenitic and duplex, hot and cold rolled, in the presence of a solution, which simulates the contact with salt contaminated concrete. The corrosion rates were determined and also their behaviour against localized corrosion (pitting.

Se ha realizado un estudio sobre la resistencia a la corrosión de barras corrugadas de acero inoxidable utilizadas en construcción civil para armar el hormigón. Con este objeto se han realizado diferentes ensayos electroquímicos en presencia de un medio acuoso básico, que simula el contacto con hormigón contaminado con sal, y se ha determinado la velocidad de corrosión y la resistencia a la formación de picaduras de diferentes calidades de aceros inoxidables (austeníticos y dúplex, tanto conformadas en caliente como en frío.

Estudio mediante difracción de rayos X de las tensiones residuales producidas durante el depósito de películas delgadas de TiN sobre sustratos metálicos

Directory of Open Access Journals (Sweden)

Mónica Monsalve

2010-01-01

Full Text Available En este trabajo se analizó la influencia que tiene el espesor de la película y el tipo de sustrato en el nivel y tipo de esfuerzos residuales generados en recubrimientos de TiN obtenidos por dos técnicas de deposición física en fase vapor: pulverización catódica con magnetrón e implantación iónica. Los sustratos utilizados fueron un acero inoxidable AISI 304 y un acero de herramientas AISI M2. Las tensiones residuales, las fases presentes y la orientación cristalográfica de las películas depositadas fueron obtenidas mediante análisis de difracción de rayos X por incidencia rasante. Se encontró que los esfuerzos residuales fueron mayores en las películas depositadas por la técnica de pulverización catódica con magnetrón que en las depositadas por la técnica de implantación iónica. En ambos casos estos esfuerzos son de compresión y disminuyen en la medida que aumenta el espesor de la película. Esto se debe a la forma como se entrega la energía, la capa en crecimiento y el momentum de las partículas ionizadas, lo que influye directamente en la microestructura y aumento o disminución de los esfuerzos residuales. En cuanto al tipo de sustrato se obtuvieron esfuerzos mayores en las películas depositadas sobre el acero AISI 304 que en las depositadas sobre el acero AISI M2, lo cual se debe posiblemente a que este último acero tiene un menor coeficiente de expansión térmica.

Oxidation behaviour at 1123 K of AISI 304-Ni/Al-Al2O3/TiO2 multilayer system deposited by flame spray

Directory of Open Access Journals (Sweden)

Cervera, I.

2011-04-01

Full Text Available The oxidation behaviour of alumina/titania (97/3, 87/13 and 60/40 ceramic coatings using a Ni-Al coupling layer was studied in a thermobalance. Both layers were deposited on an AISI 304 stainless steel base metal by the flame spray technique. The coated steel was heated from room temperature to 1,123 K at 40 K min –1, oxidized in air for 50 h, and then cooled to room temperature at 40 K min–1. The mass gain was mainly attributed to the oxidation of Ni-Al coupling layer. Kinetic laws, DW·S –1 (mg.mm–2 vs. time (hours were close to a parabolic plot for each sample. Surface composition of ceramic top layer and the cross section of multilayer system were analysed using a wide range of experimental techniques including Scanning Electron Microscopy (SEM, equipped with a link energy dispersive X-Ray spectroscopy (EDX and X-Ray diffraction (XRD before and after the oxidation process. Coatings 97/3 and 87/13 presented a stable structure after flame spray deposition and they did not evolve with the oxidation process, while most of the 60/40 coating changed to a metastable structure after deposition and to a more stable structure after oxidation with high micro-cracks content. SEM and EDX microanalysis of the cross-sections showed that significant oxidation and a weak intergranular precipitation had been produced in the coupling layer and on the stainless steel base metal, respectively.El comportamiento a oxidación de recubrimientos cerámicos alúmina/titania (97/3, 87/13, 60/40 usando una capa de anclaje Ni-Al se ha estudiado mediante una termobalanza. Ambas capas se han depositado sobre un acero inoxidable AISI 304 utilizando la técnica de proyección llama (FS. El acero recubierto se ha calentado desde la temperatura ambiente hasta 1.123 K a 40 K min–1, se ha oxidado al aire durante 50 h, y luego se ha enfriado hasta la temperatura ambiente a 40 K min–1. La ganancia en masa se atribuye a la oxidación de la capa de enganche Ni-Al. La cin

Comparative study of the microbiological corrosion among an AISI 304L and an API X65; Estudio comparativo de la corrosion microbiologica entre un AISI 304L y un API X65

Energy Technology Data Exchange (ETDEWEB)

Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Gonzalez F, E. [ITT, Toluca, Estado de Mexico (Mexico)

2004-07-01

Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

Cladding of aluminum on AISI 304L stainless steel by cold roll bonding: Mechanism, microstructure, and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Akramifard, H.R., E-mail: akrami.1367@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Mirzadeh, H., E-mail: hmirzadeh@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Parsa, M.H., E-mail: mhparsa@ut.ac.ir [School of Metallurgy and Materials Engineering, College of Engineering, University of Tehran, P.O. Box 11155-4563, Tehran (Iran, Islamic Republic of); Center of Excellence for High Performance Materials, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of); Advanced Metalforming and Thermomechanical Processing Laboratory, School of Metallurgy and Materials Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2014-09-08

The AA1050 aluminum alloy and AISI 304L stainless steel sheets were stacked together to fabricate Al/304L/Al clad sheet composites by the cold roll bonding process, which was performed at temperatures of ∼100 and 23 °C to produce austenitic and austenitic–martensitic microstructures in the AISI 304L counterpart, respectively. The peel test results showed that the threshold reduction required to make a suitable bond at room temperature is below 10%, which is significantly lower than the required reduction for cold roll bonding of Al sheets. The tearing of the Al sheet during the peel test signified that the bond strength of the roll bonded sheets by only 38% reduction has reached the strength of Al, which is a key advantage of the developed sheets. The extrusion of Al through the surface cracks and settling inside the 304L surface valleys due to strong affinity between Al and Fe was found to be the bonding mechanism. Subsequently, the interface and tensile behaviors of three-layered clad sheets after soaking at 200–600 °C for 1 h were investigated to characterize the effect of annealing treatment on the formation and thickening of intermetallic compound layer and the resultant mechanical properties. Field emission scanning electron microscopy, X-ray diffraction, and optical microscopy techniques revealed that an intermediate layer composed mainly of Al{sub 13}Fe{sub 4}, FeC and Al{sub 8}SiC{sub 7} forms during annealing at 500–600 °C. A significant drop in tensile stress–strain curves after the maximum point (UTS) was correlated to the interface debonding. It was found that the formation of intermediate layer by post heat treatment deteriorates the bond quality and encourages the debonding process. Moreover, the existence of strain-induced martensite in clad sheets was found to play a key role in the enhancement of tensile strength.

Evaluación de la adherencia del biofilm sobre salivaderas dentales de acero inoxidable, cerámica y opalina

OpenAIRE

Butler, Teresa Adela

2009-01-01

El objetivo principal de esta investigación fue estudiar el desarrollo de la biopelícula depositada sobre las salivaderas dentales de tres materiales diferentes (acero inoxidable, cerámica y opalina), de equipos odontológicos correspondientes a dos zonas diferentes del casco urbano de la ciudad de La Plata (Z1 y Z2). Para ello se realizaron 38 cortes de salivaderas dentales de los tres materiales, de cada zona En primer lugar se realizó el análisis de la microbiota planctónica y sé...

Electrochemical Study of Welded AISI 304 and 904L Stainless Steel in Seawater in View of Corrosion

Directory of Open Access Journals (Sweden)

Richárd Székely

2010-10-01

Full Text Available This is a comparative study of the corrosion behaviour of welds in AISI 304 and AISI 904L stainless steels carried out in seawater model solution in the temperature range 5-35°C and the standard of corrosion testing of welds was followed. The corrosion rate and corrosion attack characteristics were determined for welds of the examined steels with several type of treatment. The aim of this work was to compare the steels based on their resistance against the corrosion in terms of pitting potential (Epit and repassivation potential (Erepass. Seawater is an electrochemically aggressive medium, which can initiate localised corrosion in welded stainless steels. Different electrochemical and testing methods were used, including cyclic voltammetry, chronopotentiometry, electrochemical impedance spectroscopy (EIS, pH measuring and penetration tests.

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel Cementação sob plasma à baixa temperatura do aço inoxidável austenítico AISI 316L e do aço inoxidável duplex AISI F51

OpenAIRE

Carlos Eduardo Pinedo; André Paulo Tschiptschin

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% c...

Estudio de electrodeposición de cobre sobre electrodos porosos de grafito y acero inoxidable vía SEM-DRX y análisis de imagen

OpenAIRE

Constanzo-R., Robinson; Pagliero-N., Antonio; Vergara-G., Froilán

2014-01-01

El objetivo de este trabajo fue realizar un análisis cualitativo de la distribución de un electrodepósito de cobre en el interior de electrodos porosos (EP) de acero inoxidable y carbono grafito. Para ello, se realizaron pruebas de electrodepositación de cobre a nivel de laboratorio, con un posterior análisis de cortes de muestras de acero y grafito vía Microscopía Estereoscópica, Microscopía SEM-DRX y Análisis de Imagen, los cuales mostraron que el cobre no se deposita en forma uniforme al i...

Phosphate coating on stainless steel 304 sensitized;Recubrimiento fosfatado sobre acero inoxidable 304 sensibilizado

Energy Technology Data Exchange (ETDEWEB)

Cruz V, J. P. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Altamira, Km. 14.5 Carretera Tampico-Puerto Industrial Altamira, 89600 Altamira, Tamaulipas (Mexico); Vite T, J. [ININ, Carretera Mexico-Toluca s/n, Ocoyoacac 52750, Estado de Mexico (Mexico); Castillo S, M.; Vite T, M., E-mail: jpcruz@ipn.m [IPN, Escuela Superior de Ingenieria Mecanica y Electrica, Seccion de Estudios de Posgrado e Investigacion, Unidad Profesional -Adolfo Lopez Mateos-, Zacatenco, 07738 Mexico, D. F. (Mexico)

2009-07-01

The stainless steel 304 can be sensitized when welding processes are applied, that causes the precipitation of chromium carbide in the grain limits, being promoted in this way the formation of galvanic cells and consequently the corrosion process. Using a phosphate coating is possible to retard the physiochemical damages that can to happen in the corrosion process. The stainless steel 304 substrate sensitized it is phosphate to base of Zn-Mn, in a immersion cell very hot. During the process was considered optimization values, for the characterization equipment of X-rays diffraction and scanning electron microscopy was used. The XRD technique confirmed the presence of the phases of manganese phosphate, zinc phosphate, as well as the phase of the stainless steel 304. When increasing the temperature from 60 to 90 C in the immersion process a homogeneous coating is obtained. (Author)

Standard test method for electrochemical reactivation (EPR) for detecting sensitization of AISI type 304 and 304L stainless steels

CERN Document Server

American Society for Testing and Materials. Philadelphia

1994-01-01

1.1 This test method covers a laboratory procedure for conducting an electrochemical reactivation (EPR) test on AISI Type 304 and 304L (UNS No. S30400 and S30403, respectively) stainless steels. This test method can provide a nondestructive means of quantifying the degree of sensitization in these steels (1, 2, 3). This test method has found wide acceptance in studies of the effects of sensitization on intergranular corrosion and intergranular stress corrosion cracking behavior (see Terminology G15). The EPR technique has been successfully used to evaluate other stainless steels and nickel base alloys (4), but the test conditions and evaluation criteria used were modified in each case from those cited in this test method. 1.2 The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this...

TIG AISI-316 welds using an inert gas welding chamber and different filler metals: Changes in mechanical properties and microstructure

Directory of Open Access Journals (Sweden)

Sánchez, A.

2010-12-01

Full Text Available This report analyses the influence of the use of an inert gas welding chamber with a totally inert atmosphere on the microstructure and mechanical properties of austenitic AISI 316L stainless steel TIG welds, using AISI ER316L, AISI 308L and Inconel 625 as filler metals. When compared with the typical TIG process, the use of the inert gas chamber induced changes in the microstructure, mainly an increase in the presence of vermicular ferrite and ferrite stringers, what resulted in higher yield strengths and lower values of hardness. Its effect on other characteristics of the joins, such as tensile strength, depended on the filler metal. The best combination of mechanical characteristics was obtained when welding in the inert gas chamber using Inconel 625 as filler metal.

En este estudio se analiza la influencia que el uso de una cámara de soldadura de gas inerte tiene sobre la microestructura y las propiedades mecánicas de las soldaduras TIG en el acero inoxidable austenítico AISI-316L cuando se emplean AISI ER316L, AISI 308L e Inconel 625 como materiales de aporte. Cuando se compara con el típico proceso de TIG, el uso de una cámara de gas inerte induce cambios en la microestructura, incrementando la presencia de ferrita vermicular y de laminillas de ferrita, resultando en un aumento del límite elástico y una pérdida de dureza. Su influencia sobre otras características de las soldaduras como la carga de rotura depende de la composición del material de aporte. La mejor combinación de propiedades mecánicas se obtuvo usando el Inconel 625 como material de aporte y soldando en la cámara de gas inerte.

Optimización topológica y fabricación aditiva de un soporte aeronáutico mediante sinterizado láser de acero inoxidable 15-5PH

OpenAIRE

Marchal Montes, Álvaro

2016-01-01

El objetivo de este trabajó será la aplicación de la optimización topológica a un soporte usado en el sector aeronáutico para reducir su masa que posteriormente se fabricará mediante fabricación aditiva con tecnología DMLS (Direct Metal Laser Sintering) en acero inoxidable 15-5PH. Para llegar a una buena optimización topológica será necesario estudiar todos los caminos de optimización posibles hasta llegar a una correcta mediante softwares adecuados además de adaptarla a la fabricación ad...

Caracterización mecánica de recubrimientos de aluminio por CVD-FBR sobre aceros inoxidables y resistencia a la oxidación en vapor de agua

Directory of Open Access Journals (Sweden)

Diego Pérez-Muñoz

2015-09-01

Full Text Available Los recubrimientos de aluminio depositados sobre el acero inoxidable austenítico AISI 317 por Deposición Química de Vapor en Lecho Fluidizado (CVD-FBR presentan a altas temperaturas una reducción de la velocidad de corrosión de más de 80 veces. Se realizó la caracterización mecánica de los recubrimientos por medio de microdureza, nanoindentación, para conocer cómo se vieron afectas las propiedades mecánicas (en especial la dureza y el módulo de Young del recubrimiento y del sustrato luego de ser sometidos a la oxidación a alta temperatura. También se hicieron análisis por medio de Microscopia Electrónica de Barrido (MEB, para observar los cambios microestructurales, y de Microscopia de Fuerza Atómica (MFA, para observar cómo varía la topografía y el gradiente de rugosidad en función de la distancia recorrida por la punta del cantiléver durante los barridos.

Formation of abrasion-resistant coatings of the AlSiFexMny intermetallic compound type on the AISI 304L alloy

Directory of Open Access Journals (Sweden)

Martínez-Perales, Laura G.

2016-03-01

Full Text Available The α-Al9FeMnSi and β-Al9FeMn2Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 °C, pressure (5, 10 y 20 MPa and holding time (3600, 5400 y 7200 seconds. Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 °C, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of α-Al9FeMnSi and β-Al9FeMn2Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface.Los intermetálicos α-Al9FeMnSi y β-Al9FeMn2Si formados por sinterización reactiva de polvos Al, Si, Mn, Fe, Cr, Ni se han utilizado en aceros AISI 304L para mejorar la microdureza. Las variables de procesamiento de sinterización reactiva fueron temperatura (600, 650, 700, 750, y 800 °C, presión (5, 10 y 20 MPa y el tiempo de retención (3600, 5400 7200 segundos. Los resultados experimentales muestran que la temperatura es la variable más importante que afecta a la formación del sustrato/recubrimiento, mientras que la presión no parece tener un efecto significativo una influencia significativa. Los resultados muestran las condiciones óptimas de la sinterización reactiva que favorecen la formación del sustrato/recubrimiento a 800 °C, 20 MPa y 7200 segundos. En estas condiciones, la zona de reacción entre el sustrato y el recubrimiento es más compacta y bien

Microestructura de una unión disímil AISI 321 y una aleación A 351 grado HK-40 obtenida mediante soldadura manual por arco eléctrico

Directory of Open Access Journals (Sweden)

Reilis Fuentes-Guilarte

2016-05-01

Full Text Available El objetivo fue establecer el comportamiento microestructural de una unión disímil de acero inoxidable austenítico AISI 321 y de la aleación A 351 grado HK 40 obtenida por fundición mediante soldadura manual por arco eléctrico y electrodos revestidos del tipo E 309 L-16. La estructura ferrita–austeníta que se forma en la unión del acero con la aleación es resultado del elevado contenido de carbono de la segunda. La baja velocidad de enfriamiento del cordón de soldadura revela ausencia de discontinuidades en el retículo cristalino de la zona afectada térmicamente y atenúa la formación de carburos de cromo del tipo Cr23C6, que puede formar la aleación A 351 grado HK 40 durante la difusión del volumen de fracción en masa del cromo.

Biaxial fatigue tests and crack paths for AISI 304L stainless steel

Directory of Open Access Journals (Sweden)

V. Chaves

2014-10-01

Full Text Available AISI 304L stainless steel specimens have been tested in fatigue. The tests were axial, torsional and in-phase biaxial, all of them under load control and R=-1. The S-N curves were built following the ASTM E739 standard and the method of maximum likelihood proposed by Bettinelli. The fatigue limits of the biaxial tests were represented in axes σ-τ. The elliptical quadrant, appropriate for ductile materials, and the elliptical arc, appropriate for fragile materials, were included in the graph. The experimental values were better fitted with an elliptical quadrant, despite the ratio between the pure torsion and tension fatigue limits, τFL/σFL, is 0.91, close to 1, which is a typical value for fragile materials. The crack direction along the surface has been analyzed by using a microscope, with especial attention to the crack initiation zones. The crack direction during the Stage I has been compared with theoretical models.

PROTECCIÓN CONTRA LA CORROSIÓN EN SALES FUNDIDAS DE UN ACERO HOT ROLLED, EN EL RANGO DE TEMPERATURAS DE 400 ºC-600 ºC, RECUBIERTO POR ROCIADO TÉRMICO CON ACERO INOXIDABLE 312

Directory of Open Access Journals (Sweden)

JOSE LUDDEY MARULANDA

2009-01-01

Full Text Available Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono tipo hot rolled, rociado térmicamente con una aleación de acero inoxidable tipo 312, con el equipo Rototec, en una mezcla de sal 20% Na2SO4 - 80% V2O5, entre 400ºC - 600ºC, durante tiempos de 1-7-22 horas. Los resultados mostraron una moderada protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento a 600ºC. Se concluyó que la velocidad de corrosión aumenta con la temperatura y disminuye con el tiempo de exposición.

Processing of fine grained AISI 304L austenitic stainless steel by cold rolling and high-temperature short-term annealing

Science.gov (United States)

Naghizadeh, Meysam; Mirzadeh, Hamed

2018-05-01

An advanced thermomechanical process based on the formation and reversion of deformation-induced martensite was used to refine the grain size and enhance the hardness of an AISI 304L austenitic stainless steel. Both low and high reversion annealing temperatures and also the repetition of the whole thermomechanical cycle were considered. While a microstructure with average austenite grain size of a few micrometers was achieved based on cold rolling and high-temperature short-term annealing, an extreme grain refinement up to submicrometer regime was obtained by cold rolling followed by low-temperature long-term annealing. However, the required annealing time was found to be much longer, which negates its appropriateness for industrial production. While a magnificent grain refinement was achieved by one pass of the high-temperature thermomechanical process, the reduction in grain size was negligible by the repetition of the whole cycle. It was found that the hardness of the thermomechanically processed material is much higher than that of the as-received material. The results of the present work were shown to be compatible with the general trend of grain size dependence of hardness for AISI 304L stainless steel based on the Hall-Petch relationship. The results were also discussed based on the X-ray evaluation of dislocation density by modified Williamson-Hall plots.

Effect of microstructure and chemical composition on localized corrosion resistance of a AISI 304L stainless steel after nanopulsed-laser surface melting

International Nuclear Information System (INIS)

Pacquentin, W.; Caron, N.; Oltra, R.

2015-01-01

Highlights: • Laser surface melting treatments require neither additional feedstock nor contact. • By affecting 1 μm, the pitting potential of laser treated 304L increases by 500 mV. • Surface modification of laser treated sample observed by TEM. • The physico-chemical properties of the surface are correlated to overlap rate. • AISI 304L pitting corrosion resistance strongly depends of overlap rate. - Abstract: Changes induced in the surface properties of AISI 304L stainless steel when it is treated with a nanopulsed ytterbium-doped fiber laser were investigated to determine the microscale distribution of its physico-chemical properties. A Gaussian energy distribution was created with a radius of 71 μm (1/e 2 ) at the focal point. Local investigations were carried out using transmission electron microscopy to consider the effect of overlapping individual laser impacts. The results obtained reveal that laser surface melting leads to changes in the crystallographic structure of the steel through the formation of a δ-ferritic phase. It also results in the creation of an oxide layer that increases the corrosion resistance of the steel, with the chemical composition, structure and thickness of this layer being dependent on the overlap percentage and the position along the beam radius. Measurement of the localized corrosion resistance in a 30 g L −1 NaCl solution using polarization curves found that optimal laser treatment conditions can led to an increase in the breakdown potential of more than 500 mV, which corresponds to a significant improvement in corrosion resistance.

Investigation on AISI 304 austenitic stainless steel to AISI 4140 low alloy steel dissimilar joints by gas tungsten arc, electron beam and friction welding

International Nuclear Information System (INIS)

Arivazhagan, N.; Singh, Surendra; Prakash, Satya; Reddy, G.M.

2011-01-01

Research highlights: → Beneficial effects of FRW, GTAW and EBW joints of dissimilar AISI 304 and AISI 4140 materials. → Comparative study of FRW, GTAW and EBW joints on mechanical properties. → SEM/EDAX, XRD analysis on dissimilar AISI 304 and AISI 4140 materials. -- Abstract: This paper presents the investigations carried out to study the microstructure and mechanical properties of AISI 304 stainless steel and AISI 4140 low alloy steel joints by Gas Tungsten Arc Welding (GTAW), Electron Beam Welding (EBW) and Friction Welding (FRW). For each of the weldments, detailed analysis was conducted on the phase composition, microstructure characteristics and mechanical properties. The results of the analysis shows that the joint made by EBW has the highest tensile strength (681 MPa) than the joint made by GTAW (635 Mpa) and FRW (494 Mpa). From the fractographs, it could be observed that the ductility of the EBW and GTA weldment were higher with an elongation of 32% and 25% respectively when compared with friction weldment (19%). Moreover, the impact strength of weldment made by GTAW is higher compared to EBW and FRW.

Estudio comparativo de la cavidad de acceso radicular en conductos curvos con limas de níquel-titanio y taladros de acero inoxidable

OpenAIRE

Oncins Rodríguez, J.; Pumarola Suñé, José; Canalda Sahli, Carlos

2005-01-01

El propósito de este estudio fue comparar la cantidad de dentina radicular removida y evaluar el mantenimiento de la forma del conducto tras la instrumentación de los dos tercios coronarios radiculares, utilizando instrumentos de acero inoxidable (taladros de Gates Glidden) y de níqueltitanio (limas GT Flare y limas Orifice Shaper). Un total de 42 dientes humanos extraídos con conductos radiculares curvos fueron divididos en tres grupos. Los conductos se instrumentaron mecánicamente usando ta...

Comparative study of the microbiological corrosion among an AISI 304L and an API X65

International Nuclear Information System (INIS)

Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L.; Gonzalez F, E.

2004-01-01

Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

Estudio de corrosión galvánica en pares latón/acero inoxidable y latón/fundición de hierro

Directory of Open Access Journals (Sweden)

Ohanian, M.

2011-08-01

Full Text Available Corrosion attack in heat exchanger systems is a topic of main interest for the maintenance in each industrial plant. These are multigalvanic systems with particular geometric and fluidodynamic complexity. Corrosive damages include zinc selective dealeation in copper alloys. In order to explain zinc dealeation attack, this paper deals with laboratory scale testing, characterization and interactions between two copper and zinc alloys (Yellow brass –UNS C268– and Admiralty brass –UNS C443– compared to AISI 316 stainless steel and cast iron. The tests were performed at 20 °C in 1.5 % NaCl and 1.5 % Na₂SO₄ solutions, pH 8 and each material was characterized by potentiodynamic sweeps. The couples are analyzed by studying transient galvanic currents. We conclude about the cause of the analyzed pathology, brass protection potential ranges and its coupling compatibility with other metals.

El ataque por corrosión en los sistemas intercambiadores de calor constituye un problema para el mantenimiento de cualquier planta industrial. Se trata de sistemas multigalvánicos con particular complejidad geométrica y fluidodinámica. Las patologías corrosivas incluyen el fenómeno de dealeación selectiva de cinc en las aleaciones de cobre. A fin de explicar un caso particular de ataque por decinficación (deterioro en placa de intercambiador de calor de tubos de inoxidable, el presente trabajo aborda en ensayos a escala de laboratorio, la caracterización e interacciones entre dos aleaciones de cobre y cinc, (Yellow brass –UNS C268– y Admiralty brass –UNS C443–, respecto a acero inoxidable AISI 316 y fundición gris de hierro. Los ensayos se realizan a 20 °C en disoluciones de NaCl 1,5 % y Na₂SO₄ 1,5 % y pH 8. Se caracterizan electroquímicamente las aleaciones y materiales involucrados mediante barridos potenciodinámicos. Los pares galvánicos formados se analizan mediante el

A comparison of tensile, fracture and fatigue mechanical behaviour of structural reinforcing bars made with different steels

Directory of Open Access Journals (Sweden)

Rodríguez, C.

2013-09-01

Full Text Available The use of austenitic stainless steels as rebar is an option increasingly used in reinforced concrete structures exposed to aggressive environments and especially those that have to work in marine environments. The same is true for duplex stainless steel rebars, although nowadays they have a lower use, mainly due to the fact that their inclusion in the reinforced concrete standards was delayed 10 years compared to austenitic stainless steel ones, and consequently their in-service behavior is not as well known. A study of the mechanical properties, including fracture toughness, fatigue behaviour and corrosion resistance in saline alkaline environments of austenitic (AISI 304LN and 316LN and duplex (D2205 stainless steel reinforcing bars was performed in this work. Bars made on a high ductility carbon steel (B500SD that are normally used to reinforce concrete were also characterized and used as a comparison. Stainless steel reinforcing bars show mechanical properties at least similar but usually higher than one of the best carbon steel re-bars (B500SD, along with a significantly higher ductility and, of course, much better corrosion behaviour in saline alkaline environments.El uso de aceros inoxidables austeníticos como armaduras de refuerzo es una opción cada vez más utilizada en estructuras de hormigón armado expuestas a ambientes agresivos y especialmente en las que han de trabajar en ambientes marinos. Lo mismo cabe decir de las armaduras de acero inoxidable dúplex, si bien su uso es menor, debido sobre todo a que su inclusión en la normativa aplicable al armado de hormigón se retrasó 10 años con respecto a los inoxidables austeníticos y, consecuentemente, su comportamiento en servicio es menos conocido. En este trabajo se analiza el comportamiento mecánico, incluyendo fractura y fatiga, así como la resistencia a la corrosión en medios que simulan un hormigón contaminado de cloruros, de armaduras fabricadas tanto con

Determinación de tensiones por rayos x del acero AISI 1045 deformado por rodillo // Determination of stress for x‐ray of the steel AISI 1045 deformed for roller

Directory of Open Access Journals (Sweden)

Tomás Fernández‐Columbié

2012-01-01

Full Text Available El objetivo del trabajo es realizar el análisis de las tensiones a muestras de acero AISI 1045 endurecidasen frío por rodillo. Con empleo del método de Willianson–Hall se determinó las macro ymicrodeformaciones; la deformación reticular del parámetro de red; el tamaño de las cristalitas; losesfuerzos en la red cristalina y la reducción del tamaño promedio de los granos, lo que permitió establecerlos mecanismos de endurecimiento del acero AISI 1045, deformado por rodadura. Fueron medidos yanalizados diferentes puntos teniendo en cuenta los índices de Miller para la fase ferrítica del acero. Losmodelos lineales obtenidos, son estadísticamente significativos, que muestran una tendencia creciente delas propiedades mecánicas y metalúrgicas, según se incrementan las variables independientes delproceso de experimentación.Palabras claves: rodillo, rodadura, deformación plástica.__________________________________________________________________AbstractThe objective of the paper is to carry out the analysis from the tensions to steel samples AISI 1045hardened cold for roller. With employment of the method of Willianson-Hall was determined the macro andmicro deformations; the reticular deformation of the net parameter; the size of the crystallites; the efforts inthe crystalline net and the reduction of the size average of the grains, what allowed to establish themechanisms of hardening of the steel AISI 1045, deformed by rolling. They were measured and analyzeddifferent points keeping in mind the indexes of Miller for the phase ferrite of the steel. The obtained linealmodels, they are statistically significant that they show a growing tendency of the mechanical estates andmetallurgical, as the independent variables of the experimentation process are increased.Key words: roller, rolling, plastic deformation.

Estudio de la calidad de recubrimientos de hidroxiapatita sobre acero inoxidable implantable aplicados mediante proyección térmica con plasma

OpenAIRE

Bernal Gaona, Sandra Paola

2013-01-01

El objetivo de este trabajo de investigación se basó en el estudio de los parámetros del proceso de deposición de recubrimientos de hidroxiapatita sobre substratos de acero inoxidable implantable mediante el proceso de proyección térmica con plasma atmosférico, que pueden afectar de forma significativa la calidad de los recubrimientos, en cuanto a su cristalinidad y adherencia al substrato. Como parámetros a evaluar se tomaron el tamaño de grano de la hidroxiapatita, el espesor...

Efecto del contenido de azufre y del grado de desoxidación sobre la ductilidad en caliente de aceros inoxidables austeníticos resulfurados en estado de solidificación

Directory of Open Access Journals (Sweden)

Botella, J.

1998-05-01

Full Text Available The manufacture of free machining austenitic stainless steels features a specific drawback derived from their high sulphur content, which is needed for generating, into the austenitic matrix, inclusions to optimize the different machining operations. However, sulphur has a harmful effect on hot workability. This paper deals with assessing the effect of sulphur content and deoxidation level on the hot ductility of resulphurized austenitic stainless steels in as cast condition. Hot tensile tests were conducted on a Gleeble machine, at temperatures between 1,150 and 1,250°C, studying a ductility factor as a function of sulphur content, deoxidation degree, as well as type, size and distribution of sulfides. Results point out the harmful effect of increasing sulphur and oxygen contents on the hot workability of resulphurized austenitic stainless steels, and the need to control carefully the level of oxides of these steels.

La fabricación de aceros inoxidables austeníticos de alta maquinabilidad presenta una problemática específica derivada de su elevado contenido de azufre; elemento necesario para generar en la matriz austenítica inclusiones que faciliten las diferentes operaciones de mecanizado, pero perjudicial en cuanto al deterioro que produce en la deformabilidad en caliente. Este artículo describe el estudio realizado para evaluar el efecto del contenido de azufre y el grado de desoxidación sobre la ductilidad en caliente de aceros inoxidables austeníticos resulfurados, partiendo de una estructura de solidificación (as cast condition. Se realizaron ensayos de tracción en un sistema Gleeble, a temperaturas entre 1.150 y 1.250°C, analizándose el parámetro de ductilidad en función del contenido de azufre, nivel de desoxidación, y del tipo, tamaño y distribución de los sulfuros presentes. Los resultados ponen de manifiesto el efecto perjudicial de los contenidos de azufre y oxígeno sobre la deformabilidad en

Weldability of AISI 304 to copper by friction welding

Energy Technology Data Exchange (ETDEWEB)

Kirik, Ihsan [Batman Univ. (Turkey); Balalan, Zulkuf [Firat Univ., Elazig (Turkey)

2013-06-01

Friction welding is a solid-state welding method, which can join different materials smoothly and is excessively used in manufacturing industry. Friction welding method is commonly used in welding applications of especially cylindrical components, pipes and materials with different properties, for which other welding methods remain incapable. AISI 304 stainless steel and a copper alloy of 99.6 % purity were used in this study. This couple was welded in the friction welding machine. After the welding process, samples were analyzed macroscopically and microscopically, and their microhardness was measured. Tensile test was used to determine the bond strength of materials that were joined using the friction welding method. At the end of the study, it was observed that AISI 304 stainless steel and copper could be welded smoothly using the friction welding method and the bond strength is close to the tensile strength of copper. (orig.)

Efecto de las variables del procedimiento de soldadura sobre las propiedades mecánicas y la resistencia a la corrosión en depósitos de soldadura de aceros inoxidables supermartensíticos

OpenAIRE

Zappa, Sebastián

2011-01-01

La soldadura de los aceros inoxidables martensíticos ha presentado ciertas dificultades y el uso de tratamientos térmicos es normalmente obligatorio. Las razones son diferentes para cada grado de acero, pero en general, es común obtener alta dureza y baja tenacidad en la zona afectada por el calor. Este hecho está asociado con la estructura martensítica en sí misma y el contenido de carbono. Una posible solución a este problema y para alcanzar determinadas propiedades en condición como soldad...

Recubrimiento de Stellite 6 sobre acero inoxidable realizado con láser de CO₂ para válvulas de escape de motores diesel

Directory of Open Access Journals (Sweden)

Cadenas, M.

2002-12-01

Full Text Available To reduce the recovery or the replacement costs of diesel engine exhaust valves, they are manufactured with an economic base material, and a coating which is deposited on the seat valve in order to reach high hardness and good impact, corrosion and high temperature wear resistance (>550 °C and without lubrication. In this work, appropriate laser cladding parameters have been determined to obtain Stellite 6 coatings over AISI 304 steel (as plane test specimens and SAE EV8 steel (as valves substrates. One and two superimposed tracks were deposited on the seat valves, and modifying the laser power as a function of the rotated angle at the beginning and the end of the circular tracks, pores and cracks have been minimized and the thickness of the track were made uniform. Hardness, dilution and final microstructure of the different coatings have been analysed. A 10 % dilution and 550 HV in the tracks over plane test specimens was observed, while valves with one track showed 25 % and 430 HV respectively. With two superimposed tracks the hardness was up to 470 HV in the upper track.

Para abaratar el coste de recuperación o sustitución de válvulas de escape en motores diesel, estas se fabrican con un material base económico, recubriéndose el asiento de la válvula con otro material al que se exigirá elevada dureza y buena resistencia al impacto, a la corrosión y al desgaste erosivo en caliente (>550 °C y sin lubricación. Partiendo de esta idea, en el presente trabajo se han determinado los parámetros adecuados para realizar, mediante la técnica de plaqueado láser, un recubrimiento con Stellite 6, sobre sustratos de acero AISI 304 (probetas planas y SAE EV8 (válvulas reales. Sobre las válvulas, se depositaron uno y dos cordones superpuestos, se minimizó la presencia de poros y grietas, modificando el grado de solape inicial y final de los cordones circulares y la potencia en función del ángulo girado. Así, se

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

Science.gov (United States)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

2015-12-01

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO2 implanted AISI 304 - examined for different implantation and annealing parameters - is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 1016 cm-2 (Ti+) and 1 × 1017 cm-2 (O+) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 1015 cm-2 (Ti+) and 1 × 1016 cm-2 (O+). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

Corrosion under stress of AISI 304 steel in thiocyanate solutions

International Nuclear Information System (INIS)

Perillo, P.M.; Duffo, G.S.

1989-01-01

Corrosion susceptibility under stress of AISI 304 steel sensitized in a sodium thiocyanate solution has been studied and results were compared with those obtained with solutions of thiosulfate and tetrathionate. Sensitized steel type 304 is highly susceptible to corrosion when under intergranular stress (IGSCC) in thiocyanate solutions but the aggressiveness of this anion is less than that of the other sulphur anions studied (thiosulfate and tetrathionate). This work has been partly carried out in the Chemistry Department. (Author) [es

Análisis experimental del torneado de alta velocidad del acero AISI 1045 // Experimental analysis of high speed turning of AISI 1045 steel gears

Directory of Open Access Journals (Sweden)

Luís Wilfredo Hernández‐González

2012-01-01

Full Text Available El objetivo de este trabajo es el estudio experimental de la evolución del desgaste del flanco de dosinsertos de carburo recubiertos y un cermet, durante el torneado en seco del acero AISI 1045 con 500 y600 m/min de velocidad de corte. Los resultados fueron comparados utilizando el análisis de varianza y deregresión. La investigación mostró un efecto significativo de la velocidad de corte y del tiempo demaquinado en el desgaste del flanco. El mejor desempeño fue para el carburo recubierto con tres capas,mientras que a elevada velocidad de corte el carburo con dos capas sufrió el mayor desgaste, lo cual sedebe a que cuando pierde sus recubrimientos el substrato del inserto queda desprotegido y el desgastecrece rápidamente por la extremas condiciones del mecanizado por alta velocidad. Además, se planteanrecomendaciones del tiempo de maquinado de los insertos dadas las condiciones de elaboración por altavelocidad.Palabras claves: torneado de alta velocidad, desgaste del flanco, acero AISI 1045, estudio experimental.__________________________________________________________________________AbstractThis work deals with the experimental study of the flank wear evolution of two coating carbide inserts and acermet insert during the dry turning of AISI 1045 steel with 500 and 600 m/min cutting speed. The resultswere compared using the variance and regression analysis. The investigation showed a significant effectof cutting speed and machining time on the flank wear in high speed machining. The three coating layersinsert showed the best performance while the two layers insert had the worst behaviour of the cutting toolwear at high cutting speed, this is because once the coating film is peeled off, the substrate of the insertbecomes uncovered and the wear grows rapidly due to the extreme machining conditions for high speed.Besides, the machining time recommendations of inserts for the cutting conditions at high speed areexposed.Key words: high

Metallographic observations of AISI 304 - copper dissimular joints

International Nuclear Information System (INIS)

Medeiros, R.C. de; Carvalho Perdigao, S. de

1982-01-01

The current work informs on the SMAW dissimilar joints embrittled by molten Copper. Bead on plate of that metal were deposited on four different base metals to evaluate the phenomena. Conventional and non conventional welding methods were employed to obtain dissimilar joints of AISI 304-Cu. The latter were observed metallographically. These results are to be complemented by mechanical testing actually being performed. (Author) [pt

Designing of CK45 carbon steel and AISI 304 stainless steel dissimilar welds

OpenAIRE

Pouraliakbar,Hesam; Hamedi,Mohsen; Kokabi,Amir Hossein; Nazari,Ali

2014-01-01

Gas tungsten arc welding of CK45 and AISI304 stainless steel was performed through preparation of different types of samples using ER308L and ERNi-1 wires. Welded samples were studied by different techniques including optical metallography, scanning electron microscopy equipped with energy dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction, hardness measurements and impact test. It was observed that in the buttered specimen, the structure of the weld metal was completely austenitic wh...

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

International Nuclear Information System (INIS)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H.

2015-01-01

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO 2 implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10 16 cm −2 (Ti + ) and 1 × 10 17 cm −2 (O + ) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10 15 cm −2 (Ti + ) and 1 × 10 16 cm −2 (O + ). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO 2 inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

Sintering, microstructure and properties of WC-AISI304 powder composites

International Nuclear Information System (INIS)

Marques, B.J.; Fernandes, C.M.; Senos, A.M.R.

2013-01-01

Highlights: ► Total replacement of Co binder by stainless steel AISI 304 in WC based composites. ► Processing conditions for WC–stainless steel composites. ► Mechanical behavior and oxidation resistance of WC–stainless steel composites. -- Abstract: Tungsten carbide–stainless steel (AISI 304) based composites were successfully prepared by powder metallurgy routes using vacuum sintering at a maximum temperature of 1500 °C. The effects of the binder amount (between 6 and 15 wt.%) on the phase composition, microstructure and mechanical properties, namely hardness and fracture toughness, were investigated. Appreciable amount of (M,W) 6 C up to 12 wt.% was detected, especially for the higher SS contents. However, a good compromise between toughness and hardness was observed. Besides that, improved oxidation resistance was noticed in WC–SS based composites compared with WC–Co composites. The results are discussed having in mind the correlation between chemical composition, phase composition, microstructure and mechanical behavior

Surface modifications induced by hydrogen in AISI 304 stainless steel

International Nuclear Information System (INIS)

Evangelista, G.E.; Miranda, P.E.V. de

1983-01-01

Hydrogen induced surface modifications of type AISI 304 SS were studied by charging the samples in a 1N a 1N H 2 SO 4 electrolyte at room temperature. Current densities were varied from 500 to 4000 A/m 2 and charging times from 2 to 50 hours. Charged specimens were analysed using optical and electron scanning microscopy. Vickers microhardness tests with small load was also performed. Metallographic etching metodologies were developed (in black and white and colored photographies) which permited identification of all phases present. It was shown that delayed cracks appear somewhat curved on austenite and perfectly strainght on martensite, following the intersections of a phase platlets. These are the regions where α' martensite is located. The habit plane of these cracks might belong to (100) sub(γ) or (221) sub(γ) plane families. A new phenomenon termed hydrogen induced softening was observed on type AISI 304 SS at elevated current densities and/or charging times. (Author) [pt

EVALUACIÓN EXPERIMENTAL DE LA RESISTENCIA A LA CORROSIÓN DE UN ACERO AISI-SAE 4140 IMPLANTADO CON IONES DE NITRÓGENO

OpenAIRE

PEÑA, DARIO; FONTALVO, PAOLA; ESTUPIÑAN, HUGO; NIÑO, DANNIER; VESGA, WILSON

2009-01-01

Se estudió la resistencia a la corrosión de un acero AISI-SAE 4140 implantado con iones de Nitrógeno mediante la técnica 3DII (Implantación Iónica Tridimensional). Se evaluaron diferentes rugosidades de las muestras implantadas mediante técnicas electroquímicas de Rp, EIS y Tafel en una salmuera al 3% de NaCl, donde se obtuvo la mayor resistencia a la corrosión para el material implantado con menor rugosidad. Se produjo la formación de una posible capa protectora estable con la inmersión de l...

Inhibidores de escaso impacto medioambiental. Sistemas basados en tierras raras

Directory of Open Access Journals (Sweden)

Aballe, A.

1997-12-01

Full Text Available Lanthanum, Cerium and Samarium chlorides have been investigated as uniform and pitting corrosion inhibitors of AISI 434 and AISI 304 stainless steels and AA 5083 Al-Mg alloy in 3.5 % NaCl aerated aqueous solutions. Their inhibitor power was evaluated by using electrochemical techniques such as Linear and Cyclic Polarisation. In each case, the highest protection degree was found in the solution dopped with 500 ppm of CeCl₃. Similar results were obtained for additions of 500 ppm of LaCl₃. Scanning Electron Microscopy and Energy Dispersive Spectroscopy allowed us to confirm the cathodic nature of the inhibition process.

Se estudia el comportamiento de los cloruros de lantano, cerio y samario como inhibidores de los procesos de corrosión uniforme y por picaduras de los aceros inoxidables AISI 434 y AISI 304 y de la aleación de aluminio AA 5083 en disoluciones aireadas de NaCl al 3,5 %. Utilizando técnicas electroquímicas como polarización lineal y cíclica, se ha podido evaluar el poder inhibidor de estas sustancias. El mejor comportamiento inhibidor se ha obtenido para una concentración de 500 ppm de CeCl₃, si bien para los aceros se obtienen resultados del mismo orden para 500 ppm de LaCl₃. Con la ayuda de microscopía electrónica de barrido y espectroscopia de dispersión de energía se ha podido confirmar el carácter catódico del mecanismo de inhibición que tiene lugar en el proceso.

Efectos gammágenos del cobre en los aceros inoxidables 18Cr8Ni

Directory of Open Access Journals (Sweden)

Botella, J.

1997-10-01

Full Text Available From a series of 22 typical 18Cr8Ni stainless steel 40 kg ingots, with copper variable concentrations from 0.6 to 3.0 weight %, δ-ferrite is measured with a ferrite-meter device, calculating a nickel equivalent of 0.27 for copper. Some differences between the 8-ferrite and that on calculated by DeLong -excluding the copper γ-gene action- have been found because of different solidification and cooling regimes in ingot and weld cases.

A partir de una serie de 22 lingotes de 40 kg de aceros inoxidables típicos 18Cr8Ni, con concentraciones variables de cobre entre 0,6 y 3,0 % en masa, se mide la ferrita δ mediante un medidor de ferrita y se deduce para el cobre un equivalente en níquel de 0,27, a la vez que se establecen ciertas diferencias entre los contenidos de ferrita δ medida y la deducida según DeLong -excluida la acción gammágena del cobre- por el hecho de solidificar en lingotes en vez de la típica solidificación de soldaduras.

INFLUENCIA DE LOS RECUBRIMIENTOS DÚPLEX SOBRE LAS PROPIEDADES MECÁNICAS Y RESISTENCIA AL DESGASTE DEL ACERO AISI 4140 BONIFICADO

Directory of Open Access Journals (Sweden)

Francisco Javier Bolívar Osorio

Full Text Available El acero AISI 4140 es un acero de baja aleación al cromo/molibdeno de elevada resistencia mecánica y buena tenacidad, el cual se utiliza para la fabricación de piezas de maquinaria como piñones, cigüeñales, ejes de levas, etc. Sin embargo, su resistencia al desgaste es bastante limitada y suele ser mejorada mediante el tratamiento superficial de la nitruración. El propósito de este trabajo consistió en mejorar las propiedades mecánicas e incrementar la resistencia al desgaste del acero 4140 mediante la aplicación de un tratamiento superficial DUPLEX consistente en la nitruración líquida (conocida como Teniffer seguido del depósito de un recubrimiento duro de nitruro de titanio (TiN. La microestructura cristalina fue evaluada mediante difracción de rayos X, la morfología y la composición química fue determinada por microscopía SEM y espectroscopía de energía dispersiva de rayos X (EDS, las propiedades tribológicas fueron analizadas mediante mediciones en un tribómetro de tipo esfera sobre disco y la microdureza se determinó por el método Vickers. Las muestras tratadas con el recubrimiento dúplex mostraron una resistencia al desgaste 4 veces mayor que la muestra en estado bonificado, lo cual demuestra la aplicación potencial que tiene el acero 4140 sometido a este tratamiento dúplex.

Estudio de la corrosión de diferentes aleaciones en sales de carbonatos fundidos con la técnica de espectroscopía de impedancia electroquímica

Directory of Open Access Journals (Sweden)

Pérez, F. J.

2000-06-01

Full Text Available In the present work the corrosion behavior of different alloys (AISI 304, AISI 430 and TiAl6V in molten carbonates at 650EC are compared. By using the Electrochemical Impedance Technique different corrosion parameters such as the corrosion rate and the oxyde concentration and others features of the different layers of corrosion products are "in situ" determined. Take into account, the corrosion product characterization by X-ray Diffraction (XRD, Scanning Electron Microscopy (SEM and Electrochemical impedance Spectroscopy (EIS a corrosion mechanism for every tested alloy is proposed. In all cases, the corrosion mechanisms during the first hours are similar to a high temperature oxidation mechanism. When the equilibrium is established, the lithiation began by the formation of different double-layers on the surface of Li-metal oxydes. At the end of the corrosion process, one or two inner layers of metallic oxydes and one or two outer layers of Li-metal oxydes were formed. The corrosion mechanisms of the stainless steels (AISI 304 ans AISI 310S are a function of their chromium contents. TiAl6V alloy showed the best behavior against the corrosion of molten carbonates by the formation of a protective layer of mixed Li-Ti oxydes.

En el presente trabajo se compara el comportamiento frente a la corrosión de diferentes aleaciones (aceros inoxidables AISI 304 y AISI 310S y aleación TiAl6V en un electrolito de carbonatos fundidos a 650°C. Con la técnica de impedancia se determina “in situ” la velocidad de corrosión de las aleaciones, la resistencia del electrolito, es decir, la concentración del óxido disuelto y otras características de las capas de productos de corrosión. Teniendo en cuenta la caracterización de los productos de corrosión mediante difracción de rayos X (XRD y microscopía electrónica de barrido (SEM y los resultados de espectroscopía de impedancia (EIS, se propone un mecanismo para cada una de las aleaciones. En

Correlaciones entre la microestructura y la atenuación sonora en un acero inoxidable martensítico

Directory of Open Access Journals (Sweden)

Daniel Ramírez C.

2004-01-01

Full Text Available En este trabajo se exploró la relación entre la microestructura de un acero inoxidable martensítico y las variaciones en el sonido producido por un instrumento metalófono construido con dicho material. Para lograr este propósito, se hicieron copias de una de las placas de un glockenspiel y éstas fueron sometidas a diferentes tratamientos térmicos. Se construyeron montajes que permitieron producir sonidos mediante la excitación por percusión o electromagnética de las placas y se desarrollaron procedimientos para el análisis de las señales adquiridas usando programas de que permitían un análisis automático de la información. A partir de los resultados fue posible establecer correlaciones entre la microestructura obtenida con los diferentes tratamientos térmicos y características de los sonidos tales como la envolvente de atenuación y frecuencias predominantes.

Effect of Low-Temperature Sensitization on the Corrosion Behavior of AISI Type 304L SS Weld Metal in Simulated Groundwater

Science.gov (United States)

Suresh, Girija; Nandakumar, T.; Viswanath, A.

2018-05-01

The manuscript presents the investigations carried out on the effect of low-temperature sensitization (LTS) of 304L SS weld metal on its corrosion behavior in simulated groundwater, for its application as a canister material for long-term storage of nuclear vitrified high-level waste in geological repositories. AISI type 304L SS weld pad was fabricated by multipass gas tungsten arc welding process using 308L SS filler wire. The as-welded specimens were subsequently subjected to carbide nucleation and further to LTS at 500 °C for 11 days to simulate a temperature of 300 °C for 100-year life of the canister in geological repositories. Delta ferrite ( δ-ferrite) content of the 304L SS weld metal substantially decreased on carbide nucleation treatment and further only a marginal decrease occurred on LTS treatment. The microstructure of the as-welded consisted of δ-ferrite as a minor phase distributed in austenite matrix. The δ-ferrite appeared fragmented in the carbide-nucleated and LTS-treated weld metal. The degree of sensitization measured by double-loop electrochemical potentokinetic reactivation method indicated an increase in carbide nucleation treatment when compared to the as-welded specimens, and further increase occurred on LTS treatment. Potentiodynamic anodic polarization investigations in simulated groundwater indicated a substantial decrease in the localized corrosion resistance of the carbide-nucleated and LTS 304L SS weld metals, when compared to the as-welded specimens. Post-experimental micrographs indicated pitting as the primary mode of attack in the as-welded, while pitting and intergranular corrosion (IGC) occurred in the carbide-nucleated weld metal. LTS-treated weld metal predominantly underwent IGC attack. The decrease in the localized corrosion resistance of the weld metal after LTS treatment was found to have a direct correlation with the degree of sensitization and the weld microstructure. The results are detailed in the manuscript.

Effect of Low-Temperature Sensitization on the Corrosion Behavior of AISI Type 304L SS Weld Metal in Simulated Groundwater

Science.gov (United States)

Suresh, Girija; Nandakumar, T.; Viswanath, A.

2018-04-01

The manuscript presents the investigations carried out on the effect of low-temperature sensitization (LTS) of 304L SS weld metal on its corrosion behavior in simulated groundwater, for its application as a canister material for long-term storage of nuclear vitrified high-level waste in geological repositories. AISI type 304L SS weld pad was fabricated by multipass gas tungsten arc welding process using 308L SS filler wire. The as-welded specimens were subsequently subjected to carbide nucleation and further to LTS at 500 °C for 11 days to simulate a temperature of 300 °C for 100-year life of the canister in geological repositories. Delta ferrite (δ-ferrite) content of the 304L SS weld metal substantially decreased on carbide nucleation treatment and further only a marginal decrease occurred on LTS treatment. The microstructure of the as-welded consisted of δ-ferrite as a minor phase distributed in austenite matrix. The δ-ferrite appeared fragmented in the carbide-nucleated and LTS-treated weld metal. The degree of sensitization measured by double-loop electrochemical potentokinetic reactivation method indicated an increase in carbide nucleation treatment when compared to the as-welded specimens, and further increase occurred on LTS treatment. Potentiodynamic anodic polarization investigations in simulated groundwater indicated a substantial decrease in the localized corrosion resistance of the carbide-nucleated and LTS 304L SS weld metals, when compared to the as-welded specimens. Post-experimental micrographs indicated pitting as the primary mode of attack in the as-welded, while pitting and intergranular corrosion (IGC) occurred in the carbide-nucleated weld metal. LTS-treated weld metal predominantly underwent IGC attack. The decrease in the localized corrosion resistance of the weld metal after LTS treatment was found to have a direct correlation with the degree of sensitization and the weld microstructure. The results are detailed in the manuscript.

Soldabilidad del acero inoxidable austenitico

Directory of Open Access Journals (Sweden)

Pedro Pablo Torres-Medina

2002-01-01

Full Text Available This work involves welding stainless steel AISI 321H applying technical specifications according to welding standards, know the properties and phenomena that occur in the base metal and select the appropriate input material to ensure good quality of the process.

Stoichiometric titanium dioxide ion implantation in AISI 304 stainless steel for corrosion protection

Energy Technology Data Exchange (ETDEWEB)

Hartwig, A.; Decker, M.; Klein, O.; Karl, H., E-mail: helmut.karl@physik.uni-augsburg.de

2015-12-15

The aim of this study is to evaluate the applicability of highly chemically inert titanium dioxide synthesized by ion beam implantation for corrosion protection of AISI 304 stainless steel in sodium chloride solution. More specifically, the prevention of galvanic corrosion between carbon-fiber reinforced plastic (CFRP) and AISI 304 was investigated. Corrosion performance of TiO{sub 2} implanted AISI 304 – examined for different implantation and annealing parameters – is strongly influenced by implantation fluence. Experimental results show that a fluence of 5 × 10{sup 16} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 17} cm{sup −2} (O{sup +}) is sufficient to prevent pitting corrosion significantly, while galvanic corrosion with CFRP can already be noticeably reduced by an implantation fluence of 5 × 10{sup 15} cm{sup −2} (Ti{sup +}) and 1 × 10{sup 16} cm{sup −2} (O{sup +}). Surface roughness, implantation energy and annealing at 200 °C and 400 °C show only little influence on the corrosion behavior. TEM analysis indicates the existence of stoichiometric TiO{sub 2} inside the steel matrix for medium fluences and the formation of a separated metal oxide layer for high fluences.

Some mechanical properties of borided AISI H13 and 304 steels

International Nuclear Information System (INIS)

Taktak, Sukru

2007-01-01

In the present study, mechanical properties of borides formed on AISI H13 hot work tool and AISI 304 stainless steels have been investigated. Both steels have high chromium content and have a widespread use in the engineering application. Boriding treatment was carried out in slurry salt bath consisting of borax, boric acid, and ferrosilicon at temperature range of 800-950 deg. C for 3, 5, and 7 h. X-ray diffraction analysis of boride layers on the surface of steels revealed various peaks of FeB, Fe 2 B, CrB, and Ni 3 B. Metallographic studies showed that the boride layer has a flat and smooth morphology in the 304 steel while H13 steel was a ragged morphology. The characterization of the boride layer is also carried out by means of the micro-hardness, surface roughness, adhesion, and fracture toughness studies

Effect of strain-path on stress corrosion cracking of AISI 304L stainless steel in PWR primary environment at 360 deg. C

International Nuclear Information System (INIS)

Couvant, T.; Vaillant, F.; Boursier, JM.; Delafosse, D.

2004-01-01

Austenitic stainless steels (ASS) are widespread in primary and auxiliary circuits of PWR. Moreover, some components suffer stress corrosion cracking (SCC) under neutron irradiation. This degradation could be the result of the increase of hardness or the modification of chemical composition at the grain boundary by irradiation. In order to avoid complex and costly corrosion facilities, the effects of irradiation on the material are commonly simulated by applying a cold work on non-irradiated material prior to stress corrosion cracking tests. Slow strain rate tests were conducted on an austenitic stainless steel (SS) AISI 304L in PWR environment (360 deg. C). Particular attention was directed towards pre-straining effects on crack growth rate (CGR) and crack growth path (CGP). Results have demonstrated that the susceptibility of 304L to SCC in high-temperature hydrogenated water was enhanced by pre-straining. It seemed that IGSCC was enhanced by complex strain paths. (authors)

Investigation of the influential parameters of machining of AISI 304 ...

Indian Academy of Sciences (India)

application of cutting fluid results in longer tool life and better surface finish. ... parameters for turning of AISI 304 stainless steel by considering the process ... In the design of experiments (DOE) the full factorial method was used in .... Esme U 2009 Application of Taguchi method for the optimization of resistance spot welding.

Avaliação da suscetibilidade à corrosão sob tensão da ZAC do aço inoxidável AISI 316L em ambiente de reator nuclear PWR Stress corrosion cracking of stainless steel AISI 316L HAZ in PWR Nuclear reactor environment

Directory of Open Access Journals (Sweden)

Mônica Maria de Abreu Mendonça Schvartzman

2009-09-01

Full Text Available Aços carbono de baixa liga e aços inoxidáveis são amplamente utilizados nos circuitos primários de reatores nucleares do tipo PWR (Pressurized Water Reactor. Ligas de níquel são empregadas na soldagem destes materiais devido a características como elevadas resistências mecânica e à corrosão, coeficiente de expansão térmica adequado, etc. Nos últimos 30 anos, a corrosão sob tensão (CST tem sido observada principalmente nas regiões das soldas entre materiais dissimilares existentes nestes reatores. Este trabalho teve como objetivo avaliar, por comparação, a suscetibilidade à corrosão sob tensão da zona afetada pelo calor (ZAC do aço inoxidável austenítico AISI 316L quando submetida a um ambiente similar ao do circuito primário de um reator nuclear PWR nas temperaturas de 303ºC e 325ºC. Para esta avaliação empregou-se o ensaio de taxa de deformação lenta - SSRT (Slow Strain Rate Test. Os resultados indicaram que a CST é ativada termicamente e que a 325ºC pode-se observar a presença mais significativa de fratura frágil decorrente do processo de corrosão sob tensão.In pressurized water reactors (PWRs, low alloy carbon steels and stainless steel are widely used in the primary water circuits. In most cases, Ni alloys are used to joint these materials and form dissimilar welds. These alloys are known to accommodate the differences in composition and thermal expansion of the two materials. Stress corrosion cracking of metals and alloys is caused by synergistic effects of environment, material condition and stress. Over the last thirty years, CST has been observed in dissimilar metal welds. This study presents a comparative work between the CST in the HAZ (Heat Affected Zone of the AISI 316L in two different temperatures (303ºC and 325ºC. The susceptibility to stress corrosion cracking was assessed using the slow strain rate tensile (SSRT test. The results of the SSRT tests indicated that CST is a thermally

Effect of cold working on nitriding process of AISI 304 and 316 austenitic stainless steel

International Nuclear Information System (INIS)

Pereira, Silvio Andre de Lima

2012-01-01

The nitriding behavior of AISI 304 and 316 austenitic stainless steel was studied by different cold work degree before nitriding processes. The microstructure, thickness, microhardness and chemical micro-composition were evaluated through optical microscopy, microhardness, scanner electronic microscopy and x ray diffraction techniques. Through them, it was observed that previous plastic deformations do not have influence on layer thickness. However, a nitrided layer thicker can be noticed in the AISI 304 steel. In addition, two different layers can be identified as resulted of the nitriding, composed for austenitic matrix expanded by nitrogen atoms and another thinner immediately below expanded by Carbon atoms. (author)

Formación de maclas durante el enfriamiento en aceros inoxidables superferríticos envejecidos

Directory of Open Access Journals (Sweden)

Salán, M. N.

2005-12-01

Full Text Available Superferritic stainless steels show a BCC structure free of austenite at any temperature. Intermediate ageing temperatures, close to 475 °C, induce a-chromium content modulation and only after long periods of time, it is possible to detect chromium rich α' phase, which is responsible for embrittlement (475 °C embrittlement. In this work, ageing thermal treatments at intermediate temperatures in the superferritic stainless steel DIN 1.4575, have allowed to relate the associated hardness increase with time and temperature by means of a relationship that is compatible with a thermally activated process. After quenching from ageing temperature, twinning formation has been observed, and the extent of twinning is proportional to the increase in hardness, showing in this way that twinning density is proportional to embrittlement level.

Los aceros inoxidables superferríticos se caracterizan por su estructura cúbica centrada, libre de austenita a cualquier temperatura. Sometidos a temperaturas intermedias, próximas a 475 °C, revelan una modulación del contenido en Cr de la red. Después de tiempos prolongados se forma fase α', fragilizante y rica en cromo, fenómeno conocido como fragilización a 475 °C. En este trabajo, los tratamientos de envejecimiento realizados a temperaturas intermedias para un superferrítico DIN 1.4575 han permitido relacionar el incremento de dureza asociado a éstos con el tiempo de tratamiento, mediante una expresión coherente con un proceso térmicamente activado. Por otra parte, se ha detectado la presencia de maclas en el acero envejecido y templado en agua, siendo proporcional su densidad al grado de endurecimiento provocado por el tratamiento.

Friction and bending forces evaluation of AISI 304 DDQ steel sheet forming by bending tests under deep-drawing multiaxial stresses; Evaluacion de la fuerza de doblado y de friccion en el conformado de chapa de acero inoxidable AISI 304 DDQ mediante ensayos de doblado en condiciones multiaxiales de embuticion

Energy Technology Data Exchange (ETDEWEB)

Coello, J.; Miguel, V.; Ferrer, C.; Calatayud, A.; Martinez, A.

2012-11-01

Die radius is a critical area from the viewpoint of friction in forming processes. Moreover the sheet, that has been previously deformed in flange area, suffers bending and unbending stresses. Then, die-sheet contact in die radius must be especially considered in order to guarantee the suitable lubrication conditions. In the present work, a test method is carried out for evaluating an AISI 304 DDQ steel under similar conditions to those existing in the die radius area and that, usually, are not really reproduced in traditional bending under tensions tests. Deformation under pure shear condition, the bending and the radius angle have been established as variables of the tests. Results allow to obtain the apparent pressure sheet-bending tool, that increases with bending angle and decreases with tool radius. This last variable is the most significant while the bending angle has lesser influence. Although experimental results present some concordances with values obtained by analytical methods, some corrections must be considered in them in order to improve the theoretical values. (Author) 18 refs.

Deformation induced martensite in AISI 316 stainless steel

Directory of Open Access Journals (Sweden)

Solomon, N.

2010-04-01

Full Text Available The forming process leads to a considerable differentiation of the strain field within the billet, and finally causes the non-uniform distribution of the total strain, microstrusture and properties of the material over the product cross-section. This paper focus on the influence of stress states on the deformation-induced a’ martensitic transformation in AISI Type 316 austenitic stainless steel. The formation of deformation-induced martensite is related to the austenite (g instability at temperatures close or below room temperature. The structural transformation susceptibility is correlated to the stacking fault energy (SFE, which is a function not only of the chemical composition, but also of the testing temperature. Austenitic stainless steels possess high plasticity and can be easily cold formed. However, during cold processing the hardening phenomena always occurs. Nevertheless, the deformation-induced martensite transformation may enhance the rate of work-hardening and it may or may not be in favour of further material processing. Due to their high corrosion resistance and versatile mechanical properties the austenitic stainless steels are used in pressing of heat exchanger plates. However, this corrosion resistance is influenced by the amount of martensite formed during processing. In order to establish the links between total plastic strain, and martensitic transformation, the experimental tests were followed by numerical simulation.

El proceso de conformación da a lugar a una considerable diferenciación del campo de tensiones dentro de una barra de extrusión y, finalmente, causa una distribución no uniforme de la tensión total, la microestructura y propiedades del material sobre el corte transversal. En este trabajo se estudia la influencia de los estados de tensión sobre la transformación martensítica inducida por deformación en un acero inoxidable austenítico tipo AISI 316. La formación de martensita inducida por

Corrosion behaviour of AISI 204Cu and AISI 304 stainless steels in simulated pore solution

Energy Technology Data Exchange (ETDEWEB)

Kocijan, Aleksandra [Institute of Metals and Technology, Ljubljana (Slovenia)

2013-10-15

The evolution of the passive films on AISI 204Cu and AISI 304 stainless steels in simulated pore solution for steel reinforcements in concrete, and with and without the addition of chloride, was studied using cyclic voltammetry and potentiodynamic measurements. The passive layers were studied at open-circuit potential by means of X-ray photoelectron spectroscopy. The passive films on both materials predominantly contained Cr-oxides, whereas the Fe-species were markedly depleted. Mn-enrichment was also observed. The addition of chloride ions did not have a significant influence on the composition of the passive layers. The surface morphology of the products formed on the surface of both investigated materials at open-circuit potential and at high over-potentials in the presence of chloride was studied using scanning electron microscopy. (orig.)

Influence of Size on the Microstructure and Mechanical Properties of an AISI 304L Stainless Steel—A Comparison between Bulk and Fibers

Directory of Open Access Journals (Sweden)

Francisco J. Baldenebro-Lopez

2015-01-01

Full Text Available In this work, the mechanical properties and microstructural features of an AISI 304L stainless steel in two presentations, bulk and fibers, were systematically studied in order to establish the relationship among microstructure, mechanical properties, manufacturing process and effect on sample size. The microstructure was analyzed by XRD, SEM and TEM techniques. The strength, Young’s modulus and elongation of the samples were determined by tensile tests, while the hardness was measured by Vickers microhardness and nanoindentation tests. The materials have been observed to possess different mechanical and microstructural properties, which are compared and discussed.

Some aspects of thermomechanical fatigue of AISI 304L stainless steel: Part I. creep- fatigue damage

Science.gov (United States)

Zauter, R.; Christ, H. J.; Mughrabi, H.

1994-02-01

Thermomechanical fatigue (TMF) tests on the austenitic stainless steel AISI 304L have been conducted under “true≓ plastic-strain control in vacuum. This report considers the damage oc-curring during TMF loading. It is shown how the temperature interval and the phasing (in-phase, out-of-phase) determine the mechanical response and the lifetime of the specimens. If creep-fatigue interaction takes place during in-phase cycling, the damage occurs inside the ma-terial, leading to intergranular cracks which reduce the lifetime considerably. Out-of-phase cy-cling inhibits creep-induced damage, and no lifetime reduction occurs, even if the material is exposed periodically to temperatures in the creep regime. A formula is proposed which allows prediction of the failure mode, depending on whether creep-fatigue damage occurs or not. At a given strain rate, the formula is able to estimate the temperature of transition between pure fatigue and creep-fatigue damage.

EFECTO DE LA TEMPERATURA SOBRE LA RESISTENCIA A LA TRACCIÓN DE ALGUNOS REFUERZOS DE FIBRAS PARA MATRICES CERÁMICAS O POLIMÉRICAS EFEITO DA TEMPERATURA SOBRE A RESISTÊNCIA À TRAÇÃO DE ALGUNS REFORZOS DE FIBRAS PARA MATRIZES CERÁMICAS OU POLIMÉRICAS EFFECT OF TEMPERATURE ON TH E TENSILE STRENGTH OF SOME FIBER REINFORCEMENTS FOR CERAMIC OR POLYMER MATRICES

Directory of Open Access Journals (Sweden)

MARYORY ASTRID GÓMEZ

2009-07-01

Full Text Available Este artículo presenta un estudio de las propiedades termomecánicas de fibras de acero de bajo carbono, de acero inoxidable ASI-SAE 304, de aramida y de carbono. Además, se analizó el aspecto superficial de refuerzos de lana mineral de roca y lana de aluminosilicatos antes y después de someterlos a tratamientos térmicos a 1000 ºC. La resistencia a la tracción de las fibras se evaluó antes y después de someterlas a tratamientos térmicos a temperaturas de 400, 600, 800 y 1000 ºC dependiendo de la degradación que mostraran. Además, se efectuó un análisis termogravimétrico a cada tipo de fibra para determinar los cambios de peso a diferentes temperaturas. Las fibras de acero inoxidable mostraron la mayor estabilidad termomecánica, mientras que las fibras de aramida con tratamientos a 400 ºC mostraron propiedades mecánicas prácticamente nulas.Este artigo apresenta um estudo das propriedades termomecánicas de fibras de aço baixo carbono, de aço inoxidável ASI-SAE 304, de aramida e de carbono. Além disso, se analisou o aspecto superficial de reforços de lã mineral de rocha e lã de aluminosilicatos antes e depois que submetê-las a tratamentos térmicos a 1000 ºC. A resistência à tração das fibras se avaliou antes e depois de submetê-las a tratamentos térmicos a temperaturas de 400, 600, 800 e 1000 ºC dependendo da degradação que mostraram. Além disso, se efetuou uma análise termogravim étrica a cada tipo de fibra para determinar as mudanças de peso a diferentes temperaturas. As fibras de aço inoxidável mostraram a maior estabilidade termomecânica, enquanto as fibras de aramida com tratamentos a 400 ºC mostraram propriedades mecânicas praticamente nulas.This paper presents a study of the thermomechanical properties of low carbon steel, AISI-SAE 304 stainless steel, aramid and carbon fibers. Moreover, surface aspect of mineral rock wool of and aluminosilicate wool reinforcements was analyzed prior and after

The role of martensitic transformation on bimodal grain structure in ultrafine grained AISI 304L stainless steel

International Nuclear Information System (INIS)

Sabooni, S.; Karimzadeh, F.; Enayati, M.H.; Ngan, A.H.W.

2015-01-01

In the present study, metastable AISI 304L austenitic stainless steel samples were subjected to different cold rolling reductions from 70% to 93%, followed by annealing at 700 °C for 300 min to form ultrafine grained (UFG) austenite with different grain structures. Transmission electron microscopy (TEM) and nanoindentation were used to characterize the martensitic transformation, in order to relate it to the bimodal distribution of the austenite grain size after subsequent annealing. The results showed that the martensite morphology changed from lath type in the 60% rolled sample to a mixture of lath and dislocation-cell types in the higher rolling reductions. Calculation of the Gibbs free energy change during the reversion treatment showed that the reversion mechanism is shear controlled at the annealing temperature and so the morphology of the reverted austenite is completely dependent on the morphology of the deformation induced martensite. It was found that the austenite had a bimodal grain size distribution in the 80% rolled and annealed state and this is related to the existence of different types of martensite. Increasing the rolling reduction to 93% followed by annealing caused changing of the grain structure to a monomodal like structure, which was mostly covered with small grains of around 300 nm. The existence of bimodal austenite grain size in the 80% rolled and annealed 304L stainless steel led to the improvement of ductility while maintaining a high tensile strength in comparison with the 93% rolled and annealed sample

Crack propagation in stainless steel AISI 304L in Hydrogen Chemistry conditions (HWC)

International Nuclear Information System (INIS)

Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

2006-01-01

Velocities of crack growth in samples type CT pre cracking of stainless steel AISI 304l solder and sensitized thermally its were obtained by the Rising Displacement method or of growing displacement. It was used a recirculation circuit that simulates the operation conditions of a BWR type reactor (temperature of 280 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu + ion. In each essay stayed a displacement velocity was constant of 1x10 -9 m/s, making a continuous pursuit of the advance of the crack by the electric potential drop technique. Contrary to the idea of mitigation of the crack propagation velocity by effect of the addition of the hydrogen in the system, the values of the growth velocities obtained by this methodology went similar to the opposing ones under normal operation conditions. To the finish of the rehearsal one carries out the fractographic analysis of the propagation surfaces, which showed cracks growth in trans and intergranular way, evidencing the complexity of the regulator mechanisms of the IGSCC like in mitigation conditions as the alternative Hydrogen Chemistry. (Author)

INFLUENCIA DE LA NITRURACIÓN POR PLASMA SOBRE EL COMPORTAMIENTO A LA CORROSIÓN Y LA ADHESIÓN DE RECUBRIMIENTOS DLC SOBRE ACERO INOXIDABLE AISI 420

Directory of Open Access Journals (Sweden)

Jorge N. Pecina

2016-01-01

Full Text Available En este trabajo se estudió el comportamiento a la corrosió n y la adhesión de dos rec ubrimientos DLC (“Diamond Like Carbon ” , “Soft” y “Hard”, depositados por PACVD (“Plasma Assisted Chemical Vapour Deposition” sobre acero AISI 420, templado y revenido y /o nitrurado por plasma . Se analizaron por espectroscopía Raman y midió dureza en superficie. Se observó la microestructura por OM y SEM. Se realizaron pruebas de adhesión con indentación Rockwell C . S e practicaron ensayos de Niebla Salina e inmersión en HCl . Los DLC “ Soft ” presentaron una dureza de 5 00 HV y un espesor de 2 0 μm , mientras que los “ Hard ” tuvieron 1400 HV y 2 ,5 μm. Ambos recubrimientos presentaron bajo coeficiente de fricción y buena adhesión sobre el sustrato nitrurado . También presentaron buena resistencia a la corrosión atmosférica. En HCl el DLC retardó la degradación que se presentó rápidamente en las muestras sin recubrir.

Evaluación experimental de la resistencia a la corrosión de un acero aisi-sae 4140 implantado con iones de nitrógeno

OpenAIRE

PEÑA, DARIO; FONTALVO, PAOLA; ESTUPIÑAN, HUGO; NIÑO, DANNIER; VESGA, WILSON

2010-01-01

Se estudió la resistencia a la corrosión de un acero AISI-SAE 4140 implantado con iones de Nitrógeno mediante la técnica 3DII (Implantación Iónica Tridimensional). Se evaluaron diferentes rugosidades de las muestras implantadas mediante técnicas electroquímicas de Rp, EIS y Tafel en una salmuera al 3% de NaCl, donde se obtuvo la mayor resistencia a la corrosión para el material implantado con menor rugosidad. Se produjo la formación de una posible capa protectora estable con la inmersión de l...

Static strain aging type AISI-304 austenitic stainless steel

International Nuclear Information System (INIS)

Trindade, M.B.

1981-03-01

Static strain aging of type AISI-304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant, continuously relaxing and unloaded. The aging times varied between 10s and 100h, using a plastic pre deformation of 9% in most of the cases. The static strain aging of 304 steel furnished an activation energy of 23,800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snoek type mechanisms are responsible for the aging in such conditions. (Author) [pt

Constant extension rate testing of Type 304L stainless steel in simulated waste tank environments

International Nuclear Information System (INIS)

Wiersma, B.J.

1992-01-01

New tanks for storage of low level radioactive wastes will be constructed at the Savannah River Site (SRS) of AISI Type 304L stainless steel (304L). The presence of chlorides and fluorides in the wastes may induce Stress Corrosion Cracking (SCC) in 304L. Constant Extension Rate Tests (CERT) were performed to determine the susceptibility of 304L to SCC in simulated wastes. In five of the six tests conducted thus far 304L was not susceptible to SCC in the simulated waste environments. Conflicting results were obtained in the final test and will be resolved by further tests. For comparison purposes the CERT tests were also performed with A537 carbon steel, a material similar to that utilized for the existing nuclear waste storage tanks at SRS

Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm{sup 2}); Comportamiento a la fractura de un acero inoxidable AISI 304 sensibilizado en condiciones de reactor BWR (288 grados Centigrados y 80 Kg/cm{sup 2})

Energy Technology Data Exchange (ETDEWEB)

Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

1999-07-01

It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm{sup 2}). (Author)

Deposición electroforética de una porcelana dental sobre acero inoxidable austenítico 304

Directory of Open Access Journals (Sweden)

Vargas, G.

2003-02-01

Full Text Available An alternative technique for the production of dental restorations with porcelain, is the electrophoretic deposition (EPD. In this work, deposits of dental porcelain on stainless steel were obtained by EPD using water, ethanol and isopropanol as suspension mediums. The effect of the porcelain concentration, the intensity of the electric field and the suspension medium on the quantity of deposited mass were studied. All the tests were carried out at constant voltage, using a deposition time of 3 min. The particle size of the dental porcelain was in the range between 1.5 and 2.3 μm in the suspension. The results showed that the porcelain in the aqueous medium presented the major deposition velocity, in comparison with both ethanol and isopropanol. However, due to low the low suspension stability and hydrolysis of the water problems, the best coating finishes were obtained with ethanol. These results were obtained applying voltages between 70 and 150 V, for a deposition time of 3 min. Using isopropanol heterogeneous deposits were obtained due to the low suspension stability and to electrochemical reactions problems in the working electrodes, resulted from the high voltages application.

Una técnica alternativa para la fabricación de restauraciones dentales con porcelana, es la deposición electroforética (EPD. En este trabajo depósitos de porcelana dental sobre acero inoxidable fueron obtenidos por EPD utilizando como medios de suspensión: agua, etanol e isopropanol. Se estudió el efecto de la concentración de porcelana, de la intensidad del campo eléctrico y del medio de suspensión sobre la cantidad de masa depositada. Todas las pruebas fueron realizadas a voltaje constante, utilizando un tiempo de deposición de 3 min. La porcelana dental utilizada presentó un intervalo de tamaño de partícula entre 1,5 y 2,3 μm. Los resultados mostraron que la porcelana en el medio acuoso presentó la mayor velocidad de deposición, en

A three-dimensional thermal finite element analysis of AISI 304 stainless steel and copper dissimilar weldment

Science.gov (United States)

Singh, Gurdeep; Saxena, Ravindra K.; Pandey, Sunil

2018-04-01

The aim of this study to developed a 3-D thermal finite element model for dissimilar material welding of AISI-304 stainless steel and copper. Welding of similar material is widely studied using experimental and numerical methods but the problem becomes trivial for the welding of dissimilar materials especially in ferrous and nonferrous materials. Finite element analysis of dissimilar material welding is a cost-effective method for the understanding and analysis of the process. The finite element analysis has been performed to predict the heat affected zone and temperature distribution in AISI-304 stainless steel and copper dissimilar weldment using MSC Marc 2017®. Due to the difference in physical properties of these materials the behavior of heat affected zone and temperature distribution are perceived to be different. To verify the accuracy of the thermal finite element model, the welding process was simulated with butt-welded joints having same dimensions and parameters from Attarha and Far [1]. It is found from the study that the heat affected zone is larger in copper weld pads than in AISI 304 stainless steel due to large difference in thermal conductivity of these two weld pads.

Response to annealing and reirradiation of AISI 304L stainless steel following initial high-dose neutron irradiation in EBR-II

International Nuclear Information System (INIS)

Porter, D.L.; McVay, G.L.; Walters, L.C.

1980-01-01

The object of this study was to measure the stability of irradiation-induced microstructure upon annealing and, by selectively annealing out some of these features and reirradiating the material, it was expected that information could be gained concerning the role of microstructural changes in the void swelling process. Transmission electron microscopic examinations of isochronally annealed (200 to 1050 0 C) AISI 304L stainless steel, which had been irradiated at approximately 415 0 C to a fast (E > 0.1 MeV) neutron fluence of approximately 5.1 x 10 26 n/m 2 , verified that the two-stage hardness recovery with temperatures was related to a low temperature annealing of dislocation structures and a higher temperature annealing of voids and solute redistribution

Análisis experimental del desgaste entre UHMWPE y acero inoxidable 316l empleados en la manufactura de prótesis coxofemorales

Directory of Open Access Journals (Sweden)

Ricardo Gustavo Rodríguez Cañizo

2010-07-01

Full Text Available Título en inglés: Experimental wear analysis of UHMWPE and stainless 316l used in the manufacturing of coxofemoral prosthesis. Resumen La causa más común de falla en prótesis coxofemorales es el aflojamiento entre los componentes que conforman el sistema, de manera específica la copa acetabular y la cabeza femoral. En esta investigación se presenta un análisis tribológico del desgaste en los componentes mencionados, ya que cuando las superficies en contacto se desgastan, la funcionalidad mecánica del sistema se compromete, debido al cambio de geometría de los mismos, dando como resultado un juego mecánico entre la copa y la cabeza. Los materiales considerados en este estudio son el polietileno de ultra elevado peso molecular (UHMWPE, por sus siglas en inglés para la copa acetabular, y acero inoxidable 316L para la cabeza femoral. Esta combinación de materiales representa hoy en día la recomendación más usual por parte de los cirujanos para pacientes de la tercera edad. La tasa anual de desgaste se determinó de manera experimental y se cuantificó la cantidad de material desprendido durante el contacto. Se establecieron las condiciones de carga de forma analítica, considerando las que actúan sobre la cabeza femoral a lo largo del área de desgaste durante la marcha humana. Posteriormente, se realizó el análisis experimental de desgaste utilizando una máquina tribológica de configuración perno-sobre-disco (pin-on-disk, diseñada de manera específica para este estudio. Las pruebas para determinar la pérdida volumétrica de los componentes se realizaron bajo tres condiciones de operación: en seco, lubricada con agua destilada y lubricada con suero bovino. El marco experimental considerado consistió en pernos de UHMWPE sobre discos de acero inoxidable 316L simulando el desgaste equivalente a diez años de uso de la prótesis. Finalmente, de los resultados obtenidos se puede establecer que el desgaste y la cantidad de part

Wear resistance of AISI 304 stainless steel submitted to low temperature plasma carburizing

Directory of Open Access Journals (Sweden)

Marcos Antônio Barcelos

Full Text Available Abstract Despite the AISI 304 stainless steel has high corrosion/oxidation resistance, its tribological properties are poor, being one of the barriers for use in severe wear applications. Thus, there is a wide field for studying technologies that aim to increase the surface hardness and wear resistance of this material. In this work, hardness and wear resistance for AISI 304 stainless steel submitted to the thermochemical treatment by low temperature plasma carburizing (LTPC in a fixed gas mixture composition of 93% H2 and 7% CH4 are presented. Through the evaluation of the carburizing layers, it was possible to observe a substantial improvement in tribological properties after all temperature and time of treatment. This improvement is directly related to the increase of the process variables; among them temperature has a stronger influence on the wear resistance obtained using LTPC process.

COMPORTAMIENTO DE CORROSIÓN-EROSIÓN EN RECUBRIMIENTOS DE TiN/ZrN DEPOSITADOS SOBRE ACERO AISI 4140

OpenAIRE

Aperador, Willian; Mejía, Aura S; Caicedo, Julio

2014-01-01

Se depositaron películas delgadas de nitruro de titanio/nitruro de zirconio sobre acero AISI 4140 mediante un sistema multi-blanco magnetrón pulverización (sputtering) con radiofrecuencia. El proceso se desarrolló bajo el sistema de rotación del sustrato que permitió situar el sustrato de frente a los blancos de titanio y zirconio, generando la super-red con periodos de 1, 50, 100 y 200 bicapas. Las multicapas fueron evaluadas frente a la sinergia corrosión-erosión en una solución compuesta p...

Propagation of crevices in stainless steel AISI304L in conditions of hydrogen chemistry (HWC)

International Nuclear Information System (INIS)

Diaz S, A.; Fuentes C, P.; Merino C, F.; Castano M, V.

2006-01-01

Crevice growth velocities in samples of AISI 304L stainless steel thermally welded and sensitized were obtained by the Rising displacement method or of growing displacement. It was used a recirculation circuit in where the operation conditions of a BWR type reactor were simulated (temperature of 288 C and a pressure of 8 MPa) with the chemistry modified by the addition of hydrogen with and without the addition of impurities of a powerful oxidizer like the Cu ++ ion. CT pre cracked specimens were used and each rehearsal stayed to one constant displacement velocity of 1 x 10 -9 m/s (3.6 μm/hr), making a continuous pursuit of the advance of the crack by the electric potential drop technique. To the end of the rehearsal it was carried out the fractographic analysis of the propagation surfaces. The values of the growth velocities obtained by this methodology went similar to the opposing ones under normal conditions of operation; while the fractographic analysis show the cracks propagation in trans and intergranular ways, evidencing the complexity of the regulator mechanisms of the one IGSCC even under controlled ambient conditions or with mitigation methodologies like the alternative hydrogen chemistry. (Author)

Effects of Nitrogen on the DOS and the Passive Film Breakdown Potential of AISI 304 Stainless Steel

International Nuclear Information System (INIS)

Choe, Han Cheol; Kim, Kwan Hyu; Kim, Myung Soo; Lee, Ho Jong

1992-01-01

Effects of nitrogen on the degree of sensitization (DOS) and the passive film breakdown potential (Eb) of AISI 304 stainless steel were studied by potentiostat. AISI 304 stainless steel samples containing 0.02 ∼ 0.10wt% nitrogen were sensitized by heat treatment at 650 .deg. C. The DOS was measured using the double-loop reactivation method of the electrochemical potentiodynamic reactivation (EPR) test with the potential scan rate of 150 mV/min in the electrolyte of 0.5 M H 2 SO 4 + 0.01 M KSCN solution at 25 .deg. C. The passive film breakdown potential (Eb) and repassivation potential (Er) were detected by using the cyclic potentiodynamic polarization test (CPPT) in 0.5M HCI solution at 25 .deg. C. In addition, corrosion morphologies were observed by SEM and optical microscope. It was found that nitrogen additions up to 0.1wt% decreased DOS and increased Eb and Er of AISI 304 stainless steel, whereas the increasing sensitization time increased the DOS and decreased Eb and Er. The corrosion morphologies showed severe pits and intergranular attacks in the samples of low nitrogen content and high DOS

Mechanical behaviour of AISI 304/307 weldments creep tested at 7000C

International Nuclear Information System (INIS)

Pope, A.M.; Monteiro, S.N.; Silveira, T.L.

Preliminary observations on the mechanical behavior of AISI 304/347 weldments creep tested at 700 0 C are presented. The results are compared with those of similar welded joints isothermally treated at the same temperature for different times. The peculiar aspects in the mechanical behavior are discussed based on precipitation reactions which occur in the joint materials [pt

Decapado de un acero inoxidable austenítico mediante mezclas ecológicas basadas en H2O2 - H2SO4 - iones F-

Directory of Open Access Journals (Sweden)

Narváez, L.

2013-04-01

Full Text Available This study reports the pickling of 316L stainless steel using mixtures of hydrogen peroxide (H2O2, sulphuric acid (H2SO4 and fluoride ions as hydrofluoric acid (HF, sodium fluoride (NaF and potassium fluoride (KF. The decomposition of H2O2 in the mixtures was assessed at different temperatures 25 °C to 60 °C, with ferric ion contents from 0 to 40 g/l. According to the results obtained, were established the optimal condition pickling at 20 g/l of ferric ions, 25 °C and p-toluensulphonic acid as stabilizer of H2O2. The HF pickling mixture was the only capable to remove totally the oxide layer from the 316L stainless steel after 300 s. The fluoride salts pickling mixtures only remove partially the oxide layer (20 to 40 % aprox. after 300 s. When the pickling time was increased until 1200 s, the removal percentages were around to 80 %.En este estudio se presenta el decapado del acero inoxidable austenítico 316L utilizando mezclas de peróxido de hidrógeno (H2O2/ácido sulfúrico (H2SO4/iones fluoruro; los iones fluoruro provienen del ácido fluorhídrico (HF, fluoruro de sodio (NaF y fluoruro de potasio (KF. La estabilidad del H2O2 fue valorada modificando las concentraciones del ión férrico de 0 a 40 g/l y las temperaturas de 25 °C a 60 °C en las mezclas decapantes. Se establecieron las condiciones óptimas de decapado utilizando 20 g/l de iones férrico a 25 °C empleando el ácido p-toluensulfónico como estabilizante del H2O2. La mezcla que contenía HF fue la única capaz de eliminar completamente los óxidos superficiales del acero a tiempos de 300 s. Las mezclas a base de sales fluoradas eliminaron parcialmente los óxidos (20 y 40 % aprox. en 300 s. Al incrementar el tiempo de decapado hasta 1200 s se obtuvieron porcentajes de eliminación alrededor de un 80 %.

Corrosion of stainless steel grades in molten NaOH/KOH eutectic at 250 C: AISI304 austenitic and 2205 duplex

Energy Technology Data Exchange (ETDEWEB)

Bozzini, B.; Bogani, F.; Scarselli, G. [Dipartimento di Ingegneria dell' Innovazione, Universita del Salento, Via per Monteroni, 73100 Lecce (Italy); Barella, S.; Boniardi, M. [Dipartimento di Meccanica, Politecnico di Milano, via La Masa 34, 20156 Milano (Italy); Giovannelli, G.; Natali, S. [Dipartimento DICMA, Universita di Roma ' ' La Sapienza' ' , via Eudossiana 18, 00184 Roma (Italy)

2012-11-15

The present paper focuses on the corrosion of an austenitic (AISI304) and a duplex (2205) stainless steel grade in molten KOH/NaOH 50 w/o eutectic at 250 C. Experimental activities have been performed consisting in electrochemical measurements (linear sweep voltammetry and electrochemical impedance spectrometry) complemented by metallographic (in-plane and cross-sectional SEM micrography), structural (X-ray diffractometry) and compositional (EDX line-profiles) characterisation of the materials attacked under electrochemically controlled conditions. Electrochemical measurements have shown that AISI304 exhibits a passivating behaviour, characterised by two passivation peaks and a transpassive threshold, while duplex, does not yield a clear indication of passivation. AISI304 was found to fail by intergranular corrosion and to be covered in both passive and transpassive conditions, by an incoherent scale, containing electrolyte species. Duplex samples, instead tends to fail by homogeneous attack and exhibit a range of scale structures, depending on the applied potential. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The influence of plasma nitriding on the fatigue behavior of austenitic stainless steel types AISI 316 and AISI 304

International Nuclear Information System (INIS)

Varavallo, Rogerio; Manfrinato, Marcos Dorigao; Rossino, Luciana Sgarbi; Spinelli, Dirceu; Riofano, Rosamel Melita Munoz

2010-01-01

The plasma nitriding process has been used as an efficient method to optimize the surface properties of steel and alloy in order to increase their wear, fatigue and corrosion resistance. This paper reports on a study of the composition and influence of the nitrided layer on the high-cycle fatigue properties of the AISI 316 and 304 type austenitic stainless steels. Test specimens of AISI 316 and 304 steel were nitrided at 400 deg C for 6 hours under a pressure of 4.5 mbar, using a gas mixture of 80% volume of H 2 and 20% volume of N 2 . The rotary fatigue limit of both nitrided and non-nitrided steels was determined, and the effect of the treatment on the fatigue limit of the two steels was evaluated. The mechanical properties of the materials were evaluated based on tensile tests, and the nitrided layer was characterized by microhardness tests, scanning electron microscopy and X-ray diffraction. The resulting nitride layer showed high hardness and mechanical strength, increasing the fatigue limit of the nitrided material in comparison with the non-nitrided one. The fatigue limit of the 316 steel increased from 400 MPa to 510 MPa in response to nitriding, while that of the 304 steel increased from 380 MPa to 560 MPa. One of the contributing factors of this increase was the introduction of residual compressive stresses during the surface hardening process, which reduce the onset of crack formation underneath the nitride layer. (author)

Evaluación del comportamiento a fatiga de una unión soldada a tope de acero AISI 1015//Evaluation of the fatigue behaviour of a butt welded joint of AISI 1015 steel

Directory of Open Access Journals (Sweden)

Pavel Michel Almaguer‐Zaldivar

2015-01-01

Full Text Available Las uniones soldadas son un componente importante de una estructura, por lo que siempre es necesario conocer la respuesta de las mismas sometidas a cargas cíclicas. El objetivo de este trabajo es obtener la curva S-N de una unión soldada a tope de acero AISI 1015 y electrodo E6013 como material de aporte. Los ensayos a fatiga se realizaron de acuerdo a la norma ASTM en una máquina universal MTS810. Se utilizaron probetas de sección rectangular. El ciclo de carga fueasimétrico a tracción, con un coeficiente de asimetría de 0,1. Se obtuvo que la unión estudiada tiene un límite de resistencia a la fatiga de 178 MPa, a un punto de corte de 2 039 093 ciclos.Palabras claves: unión soldada, fatiga, curva S-N, AISI 1015, electrodo E6013._______________________________________________________________________________AbstractWelded joints are an important component in structures, by this reason is necessary to know the behaviour of these elements under cyclic loads. The objective of this work is to obtain the S-N curve of the butt welded joint of AISI 1015 steel and electrode E6013 as the contribution material. Fatiguetest was realized within the ASTM standard in the MTS810 testing machine. Rectangular cross section specimens was used. Cyclic loads was asymmetric tensile and the asymmetry ratio used was 0,1. In this study was obtained the fatigue limit equal to 178 MPa, at the cut point of 2 039 093 cycles.Key words: welded joint, fatigue, S-N curve, AISI 1015 steel, electrode E6013.

The influence of Reynolds number on the galvanic corrosion of the copper/AISI 304 pair in aqueous LiBr solutions

International Nuclear Information System (INIS)

Montanes, M.T.; Sanchez-Tovar, R.; Garcia-Anton, J.; Perez-Herranz, V.

2009-01-01

The influence of Reynolds number on the galvanic corrosion of the copper/AISI 304 stainless steel pair in a concentrated lithium bromide solution was investigated according to the mixed potential theory. A hydraulic circuit was designed to study dynamic corrosion processes in situ. A potential relation between corrosion current density (i corr ) and Reynolds number (Re) was found for copper, showing a mixed control of a chemical step and mass transport through the corrosion products film with the predominance of the former. No dependence of i corr on Re could be established for AISI 304, showing a chemical step control. Moreover, under stagnant conditions, partial passivation may occur in AISI 304; however, under flowing conditions passivation is not possible. Copper is the anodic element of the pair under all flowing conditions analysed. The galvanic phenomenon is more important as Re increases, but the results show compatibility of both materials at all Re values analysed. Similarly, a potential relation between galvanic current density (i G ) and Re was found, showing a mixed control of a chemical step and mass transport with the predominance of the latter. Copper corrosion resistance decreases more rapidly as Re increases due to the AISI 304 galvanic effect: there is a synergy between the galvanic effect and the hydrodynamic conditions. Under stagnant conditions, the galvanic behaviour of the materials is close to the compatibility limit and an inversion of the anodic element of the galvanic pair takes place.

Corrosion behaviour of AISI 304 stainless steel subjected to massive laser shock peening impacts with different pulse energies

International Nuclear Information System (INIS)

Lu, J.Z.; Qi, H.; Luo, K.Y.; Luo, M.; Cheng, X.N.

2014-01-01

Highlights: •Laser shock peening caused an obvious increase of corrosion resistance of 304 steel. •Corrosion resistance of stainless steel increased with increasing pulse energy. •Mechanism of laser shock peening on corrosion behaviour was also entirely determined. -- Abstract: Effects of massive laser shock peening (LSP) impacts with different pulse energies on ultimate tensile strength (UTS), stress corrosion cracking (SCC) susceptibility, fracture appearance and electrochemical corrosion resistance of AISI 304 stainless steel were investigated by slow strain rate test, potentiodynamic polarisation test and scanning electron microscope observation. The influence mechanism of massive LSP impacts with different pulse energies on corrosion behaviour was also determined. Results showed that massive LSP impacts effectively caused a significant improvement on UTS, SCC resistance, and electrochemical corrosion resistance of AISI 304 stainless steel. Increased pulse energy can also gradually improve its corrosion resistance

Losas de concreto reforzadas con acero inoxidable de desecho Reinforced concrete slabs with stainless steel waste

Directory of Open Access Journals (Sweden)

Jorge Alberto Pérez González

2008-08-01

Full Text Available Se muestran los resultados de un programa experimental que explora la reutilización de materiales de desecho industrial (específicamente láminas de acero inoxidable producto de la acuñación de moneda como refuerzo en losas de concreto. Para ello se elaboraron 23 especímenes tipo viga-losa a escala natural con dicho refuerzo a fin de determinar su comportamiento en términos de resistencia, ductilidad y formas de falla; el análisis experimental de modelos ensayados con diferentes cantidades de refuerzo muestra que en algunos casos, bajo ciertas condiciones de cuantías y colocación del mismo, es posible alcanzar capacidades de carga y formas de falla similares a las de especímenes de control con refuerzo tradicional. En base a estos resultados se concluye en la factibilidad de utilizar el material arriba descrito como refuerzo alternativo en elementos estructurales de concreto, tratando de encontrar alternativas más económicas en la construcción de vivienda popular.The results from an experimental program that explores the use of industrial waste materials (specifically sheets of stainless steel that result of the currency coinage as reinforcement for concrete slabs are presented. Twenty three full size beam-deck specimens were built in order to measure resistance, ductility and failure modes; the experimental analysis in models with reinforcement in different quantities shows that in some cases, under certain quantities and location, it is possible to reach similar load capacities and failure modes as specimens with traditional reinforcement. Based on these results, it is concluded the feasibility of using the material described above as alternative reinforcement in structural concrete elements, as an economic option in the construction of social housing.

Nitrocarburación mediante el proceso TENIFER QDQ de aceros inoxidables austeníticos estabilizados : caracterización química y estudio de su comportamiento frente al desgaste y la corrosión

OpenAIRE

Bellas Muiño, Leonardo

2016-01-01

[Resumen]La nitrocarburación en baño de sales se utiliza para mejorar las propiedades tribológicas de los aceros inoxidables. Sin embargo, la aparición de carburos y nitruros de elementos de aleación en la capa externa puede tener efectos contraproducentes para su resistencia a la corrosión. Por este motivo, el proceso TENIFER®QPQ introduce una etapa de oxidación a altas temperaturas con objeto de formar una capa de magnetita (Fe3O4) que incrementa la resistencia a la corrosión...

Corrosion behavior of plasma sprayed hydroxyapatite and hydroxyapatite-silicon oxide coatings on AISI 304 for biomedical application

International Nuclear Information System (INIS)

Singh, Gurpreet; Singh, Hazoor; Sidhu, Buta Singh

2013-01-01

The objective of this study is to evaluate corrosion resistance of plasma sprayed hydroxyapatite (HA) and HA-silicon oxide (SiO 2 ) coated AISI 304 substrates. In HA-SiO 2 coatings, 10 wt% SiO 2 and 20 wt% SiO 2 was mixed with HA. The feedstock and coatings were characterized by X-ray diffraction and scanning electron microscopy/energy dispersive X-ray spectroscopy. The corrosion resistance was determined for the uncoated and coated samples. The corrosion resistance of the AISI 304 was found more after the deposition of the HA-SiO 2 coatings rather than HA coating and uncoated. All the coatings were crack free after 24 h dipping in Ringer's solution for electrochemical corrosion testing.

Plasma nitriding process by direct current glow discharge at low temperature increasing the thermal diffusivity of AISI 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Prandel, L. V.; Somer, A.; Assmann, A.; Camelotti, F.; Costa, G.; Bonardi, C.; Jurelo, A. R.; Rodrigues, J. B.; Cruz, G. K. [Universidade Estadual de Ponta Grossa, Grupo de Espectroscopia Optica e Fotoacustica de Materiais, Departamento de Fisica, Av. Carlos Cavalcanti, 4748, CEP 84030-900, Ponta Grossa, PR (Brazil)

2013-02-14

This work reports for the first time on the use of the open photoacoustic cell technique operating at very low frequencies and at room temperature to experimentally determine the thermal diffusivity parameter of commercial AISI304 stainless steel and AISI304 stainless steel nitrided samples. Complementary measurements of X-ray diffraction and scanning electron microscopy were also performed. The results show that in standard AISI 304 stainless steel samples the thermal diffusivity is (4.0 {+-} 0.3) Multiplication-Sign 10{sup -6} m{sup 2}/s. After the nitriding process, the thermal diffusivity increases to the value (7.1 {+-} 0.5) Multiplication-Sign 10{sup -6} m{sup 2}/s. The results are being associated to the diffusion process of nitrogen into the surface of the sample. Carrying out subsequent thermal treatment at 500 Degree-Sign C, the thermal diffusivity increases up to (12.0 {+-} 2) Multiplication-Sign 10{sup -6} m{sup 2}/s. Now the observed growing in the thermal diffusivity must be related to the change in the phases contained in the nitrided layer.

Resistencia a la oxidación de aleaciones Ni-Cr-Al plaqueadas por láser sobre aceros al carbono e inoxidables austeníticos

Directory of Open Access Journals (Sweden)

de Damborenea, J.

1995-04-01

Full Text Available Laser surface cladding has been carried out by means of a 5 kW CO₂ continuous wave laser on both a mild and a stainless steel. A powder injection technique has been used to deliver a Ni-Cr-Al alloy onto the steel molten pool. After processing, samples were analyzed by optical and scanning electron microscopy in order to know the microstructure and composition of present phases. High temperature corrosion resistance tests were done in an oxidant environment at temperatures of 950 °C. Phase transformations and corrosion behaviour are discussed. A general conclusion is the suitability of these alloys to bear oxidation due to the formation of protective oxide layers on their surface.

Se realiza un estudio sobre la obtención de recubrimientos de superficie mediante un láser continuo de CO₂ de 5 kW de potencia de salida. Mediante la técnica de inyección de partículas, se realizaron plaqueados en superficie de Ni-Cr-Al sobre un acero suave y otro inoxidable de tipo 316. Tras el procesado, se estudió la microestructura de las probetas obtenidas. Posteriormente, se procedió a su ensayo en atmósfera oxidante a 950 °C, observándose la evolución de la microestructura, la formación de las capas de óxido y la cinética del proceso. Como conclusión general, destaca, independientemente de la base sobre la que se obtienen los recubrimientos, la gran resistencia del material a la oxidación, seguramente debida a la formación de capas de alúmina que actúan como barreras frente al ataque del oxidante.

The effect of plasma arc process parameters on the properties of dissimilar AISI 1040/AISI 304 steel plate welds

Energy Technology Data Exchange (ETDEWEB)

Kilic, Musa; Kirik, Ihsan; Orhan, Nuri [Firat Univ., Elazig (Turkey); Celik, Ferkan [Science Industry and Technology Ministry of Turkey (Turkey)

2012-11-01

In this study, 10 mm thick AISI 1040 and AISI 304 steel plates were welded in the butt position without pretreatment by plasma transferred arc (PTA) welding technique. Therefore, mechanical behaviour, microstructure, penetration depth and length were investigated. After welding, microstructural changes in the interface regions of the welded specimens were examined by scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). Micro-hardness as well as V-notch Charpy tests were performed to determine the mechanical properties of the welds. The influence of the welding parameters on the dimension and shape of the joints has been found out. From the results, it was derived that with the parameters used, a partly keyhole weld bead formed with a penetration depth of 10 mm and a width of 11 mm in butt position. (orig.)

Comportamiento frente a la corrosión de los aceros inoxidables AISI 430L P/M

OpenAIRE

Corpas, F. A.; Iglesias, F. J.; Ruiz, J. M.; Codina, S.; Ruiz, J. M.; García, V.

2004-01-01

In this paper we have studied the resistance to corrosion of the 430L ferritic stainless steels, manufactured by powder metallurgy. We have compared the behaviour of the different series of 430L stainless steels sintered, tempered and annealing, in different corrosive environments. Finally, the microstructure of the steels was determined by means of scanning electron microscopy. The better resistance to corrosion are produced in the steel annealing to 300ºC and 600ºC.

En es...

Comportamiento a fatiga del vástago de una prótesis para cadera al caminar//Fatigue behavior stem hip prosthesis for walking

OpenAIRE

Ángel Martínez-Delfín; Javier García-de-la-Figal-Costales; Luís Manuel Rodríguez-Milián; Reynaldo Rodríguez-Pérez

2014-01-01

La prótesis de cadera consiste en sustituir la parte superior fracturada del fémur por una pieza de material biocompatible. Debido a las cargas aleatorias que sobre esta prótesis actúan al caminar la persona injertada, surge la fatiga sobre la prótesis. En este trabajo se realiza el cálculo a fatiga del vástago de una prótesis de caderas fabricada con acero inoxidable austenítico AISI 316L GrQ y de uso actual. Para ellose emplea el método de los elementos finitos, considerando la compleja geo...

Estudio de la corrosión en caliente de la aleación aisi-sae 304h, mediante la técnica de espectroscopía de impedancia electroquímica (eis

Directory of Open Access Journals (Sweden)

JOSÉ TRISTANCHO

2007-01-01

Full Text Available La corrosión en caliente es uno de los mayores problemas que se presentan en la industria generadora de energía eléctrica, especialmente en los componentes que conforman los equipos generadores de vapor (calderas. El fenómeno corrosivo que presentan las sales fundidas, es por lo menos parcialmente, de naturaleza electroquímica y por lo tanto, puede ser estudiado empleando la técnica de impedancia electroquímica (EIS, adaptada a las condiciones especiales de temperatura y composición del medio corrosivo. En esta investigación se evalúo el comportamiento del acero AISI304H expuesto a un electrolito compuesto de 80%V2O5 – 20%Na2SO4 fundido, en un intervalo de temperatura comprendido entre 550ºC y 700ºC

Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

International Nuclear Information System (INIS)

Aadhavan, R.; Suresh Babu, K.

2017-01-01

Highlights: • Ceria coating reduced the oxidation kinetics of AISI304 by 3–4 orders. • Lower deposition rate (0.1 Å/s) resulted in dense and uniform coating. • Substrate temperature of 100 °C provided coating with smaller crystallite size. • Surface morphology of the coating has strong influence in oxidation protection. - Abstract: Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50–300 °C) and deposition rate (0.1–50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7–18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10"−"3 kg"2 m"−"4 s"−"1 while ceria coating lowered the kinetics by 3–4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

Energy Technology Data Exchange (ETDEWEB)

Aadhavan, R.; Suresh Babu, K., E-mail: sureshbabu.nst@pondiuni.edu.in

2017-07-31

Highlights: • Ceria coating reduced the oxidation kinetics of AISI304 by 3–4 orders. • Lower deposition rate (0.1 Å/s) resulted in dense and uniform coating. • Substrate temperature of 100 °C provided coating with smaller crystallite size. • Surface morphology of the coating has strong influence in oxidation protection. - Abstract: Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50–300 °C) and deposition rate (0.1–50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7–18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10{sup −3} kg{sup 2} m{sup −4} s{sup −1} while ceria coating lowered the kinetics by 3–4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

Effect of Adenine Concentration on the Corrosion Inhibition of Aisi ...

African Journals Online (AJOL)

This gave a surface coverage of 0.8956 and corrosion penetration rate of 0.022132mm/yr. Hence, the best adenine concentration for the corrosion inhibition of alloys 304L in 1.0M sulphuric acid solution to obtain optimum inhibition efficiency is 0.011M. Keywords: Corrosion, AISI 304L Steel, Inhibition efficiency, Degree of ...

Martensite phase reversion-induced nano/ ultrafine grained AISI 304L stainless steel with magnificent mechanical properties

Directory of Open Access Journals (Sweden)

Mohammad Shirdel

2015-06-01

Full Text Available Austenitic stainless steels are extensively used in various applications requiring good corrosion resistance and formability. In the current study, the formation of nano/ ultrafine grained austenitic microstructure in a microalloyed AISI 304L stainless steel was investigated by the advanced thermomechanical process of reversion of strain-induced martensite. For this purpose, samples were subjected to heavy cold rolling to produce a nearly complete martensitic structure. Subsequently, a wide range of annealing temperatures (600 to 800°C and times (1 to 240 min were employed to assess the reversion behavior and to find the best annealing condition for the production of the nano/ultrafine grained austenitic microstructure. Microstructural characterizations have been performed using X-ray diffraction (XRD, scanning electron microscopy (SEM, and magnetic measurement, whereas the mechanical properties were assessed by tensile and hardness tests. After thermomechanical treatment, a very fine austenitic structure was obtained, which was composed of nano sized grains of ~ 85 nm in an ultrafine grained matrix with an average grain size of 480 nm. This microstructure exhibited superior mechanical properties: high tensile strength of about 1280 MPa with a desirable elongation of about 41%, which can pave the way for the application of these sheets in the automotive industry.

Processing of plane strain compression test results for investigation of AISI-304 stainless steel constitutive behavior

International Nuclear Information System (INIS)

Aksenov, Sergey A.; Puzino, Yuriy A.; Bober, Stanislav A.; Kliber, Jiri

2015-01-01

The paper is oriented toward the determination of constitutive equation constants by the inverse analysis of plane strain compression test results. The interpretation of such results is complicated by the inhomogeneity of strain rate distribution in the specimen caused by rigid ends, the lateral spreading of a specimen friction and the variation of temperature during the test. The results of plane strain compression tests of AISI-304 stainless steel are presented and significant deviations of temperature are observed at higher strain rates. Finite element simulation was performed to estimate the inhomogeneity of strain rate within the specimen and evaluate the effect of friction on the test results. Constitutive equations of the material were obtained by inverse analysis minimizing the deviations between the measured load values and the ones predicted by numerical simulation. Keywords: PSCT, AISI-304, Gleeble, constitutive equations, hot forming, FEM, inverse analysis.

Síntesis y caracterización de recubrimientos de tin, tic y ticn sobre acero aisi 4340

Directory of Open Access Journals (Sweden)

Héctor E. Jaramillo Suárez

2004-01-01

Full Text Available En este trabajo se crecieron películas de TiN, TiC y TiCN sobre aceros AISI 4340, con el objeto de comparar los resultados estructurales, morfológicos y mecánicos al crecerlos sobre un mismo substrato. Se utilizó un láser pulsado Nd: YAG con energía de 500mJ, longitud de onda de 1064 nm y tasa de repetición de 10 Hz. Mediante microscopia de Fuerza Atómica AFM, se observó que los recubrimientos presentan alta homogeneidad y tamaño de grano fino. Por Microscopía Electrónica de Barrido se determinó presencia de microgotas en los recubrimientos. Se aplicó prueba de tensión para determinar la adhesión de las películas; aplicando cargas máximas de 60 Kgf, los recubrimientos no mostraron señales de desprendimiento del substrato. A todos los recubrimientos se les sometió a prueba de dureza Rockwell C, con el fin de determinar la resistencia a la fractura, indicando que estos recubrimientos son aptos para diferentes aplicaciones en la industria.

The electrochemical behaviour of stainless steel AISI 304 in alkaline solutions with different pH in the presence of chlorides

International Nuclear Information System (INIS)

Freire, L.; Carmezim, M.J.; Ferreira, M.G.S.; Montemor, M.F.

2011-01-01

Highlights: → The passivation and passivation breakdown of AISI 304 in alkaline solutions with different pH was studied. → The electrochemical behaviour and the corrosion resistance in chloride environments were evaluated using d.c. potentiodynamic polarization and electrochemical impedance spectroscopy. → The results were modelled using a hierarchically distributed circuit and revealed a more susceptible surface at pH 9. → The passive film characterization was carried out by SEM and EDS analysis, revealing the existence of MnS inclusions and the increase of Cr/Fe ratio in the attacked areas, preferably the vicinity of those inclusions. - Abstract: Nowadays, stainless steel reinforcements appear as an effective solution to increase the durability of reinforced concrete structures exposed to very aggressive environments. AISI 304 is widely used for this purpose. Although the improved durability of reinforcing AISI 304, when compared to carbon steel, there is a high probability of pitting susceptibility in the presence of chlorides. Thus, the present work aims at studying the passivation and passivation breakdown of AISI 304 in alkaline solutions of different pH (pH from 13 to 9), simulating the interstitial concrete electrolyte. These solutions were contaminated with different concentrations of chloride ions (3% and 10%, as NaCl). The electrochemical behaviour was evaluated by d.c. potentiodynamic polarization and by electrochemical impedance spectroscopy (EIS). The morphological features and the changes observed in the surface composition were evaluated by Scanning Electron Microscopy (SEM) together with EDS chemical analysis. The results evidence that pH plays an important role in the evolution of the film resistance and charge transfer processes. Moreover, the effect is highly dependent upon the chloride content and immersion time.

X-Ray diffraction application in studying the nitrogen fixing and aging in stainless steel AISI 304

International Nuclear Information System (INIS)

Ramos, L.F.V.

1973-01-01

Solid solutions of N in AISI-304 stainless steels were aged to different degrees. The aging was monitored through X-Ray difraction measurement of the lattice parameter 'a'. The increases in 'a', due to the increase of N in solid solution were determined experimentally

Spring back evaluation by bending under tension tests in conditions of multiaxial stresses corresponding to deep drawing processes. Application to AISI 304 DDQ stainless steel sheet; Evaluacion del springback mediante ensayos de doblado bajo tension en condiciones de multiaxialidad tipicas de los procesos de embuticion profunda. Aplicacion a chapa de acero inoxidable AISI 304 DDQ

Energy Technology Data Exchange (ETDEWEB)

Miguel, V.; Coello, J.; Martinez, A.; Calatayud, A.

2013-09-01

In this paper, a methodology has been developed for evaluating the spring back of AISI 304 DDQ stainless steel sheet based on a bending under tension test. The main difference of the methodology herein carried out is that tests are made under the multiaxial stresses state that take place in deep drawing processes. This affects to the level of stress value in the test and to the hardening state of the sheet. Springback evaluation has been done in two different areas. Bending area has been evaluated from elastic recovery ratio defined as the ratio between the bending radius after and before bending. Bending and unbending extreme has been studied from the measured curvature radius in this area and taking into account the geometric equivalence of the test with the drawing cups process. Results found allow to state that drawing ratio or deformation ratio have a negligible influence on the springback into the range of values experimented here. Bending radius has hardly influence as well while bending angle is the most significant variable. The results obtained are compared to those measured in deep-drawn cups, finding a great agreement. (Author)

Topological characterization of static strain aging of type AISI 304 austenitic stainless steel

International Nuclear Information System (INIS)

Monteiro, S.N.; Miranda, P.E.V. de

1981-01-01

Static strain aging of type AISI 304 austenitic stainless steel was studied from room temperature up to 623K by conducting tests in which the load was held approximately constant. The aging times varied between 10s and 100h, using a plastic pre-deformation of 9%. The static strain aging of 304 steel furnished an activation energy of 23.800 cal/mol. This implies that vacancies play an important role on the aging process. The curve of the variation of the discontinuous yielding with aging time presented different stages, to which specific mathematical expressions were developed. These facts permited the conclusion that Snock type mechanisms are responsible for the aging in such conditions. (Author) [pt

OPTIMIZATION OF SURFACE ROUGHNESS OF AISI 304 AUSTENITIC STAINLESS STEEL IN DRY TURNING OPERATION USING TAGUCHI DESIGN METHOD

Directory of Open Access Journals (Sweden)

D. PHILIP SELVARAJ

2010-09-01

Full Text Available The present work is concentrated with the dry turning of AISI 304 Austenitic Stainless Steel (ASS. This paper presents the influence of cutting parameters like cutting speed, feed rate and depth of cut on the surface roughness of austenitic stainless steel during dry turning. A plan of experiments based on Taguchi’s technique has been used to acquire the data. An orthogonal array, the signal to noise (S/N ratio and the analysis of variance (ANOVA are employed to investigate the cutting characteristics of AISI 304 austenitic stainless steel bars using TiC and TiCN coated tungsten carbide cutting tool. Finally the confirmation tests that have been carried out to compare the predicted values with the experimental values confirm its effectiveness in the analysis of surface roughness.

Elasto-plastic hardening models adjustment to ferritic, austenitic and austenoferritic Rebar; Ajuste de los aceros corrugados ferríticos, austeníticos y austenoferríticos a los modelos de endurecimiento elastoplástico por deformación

Energy Technology Data Exchange (ETDEWEB)

Hortigóna, B.; Gallardo, J.M.; Nieto-García, E.J.; López, J.A.

2017-09-01

The elastoplastic behaviour of steel used for structural member fabrication has received attention to facilitate a mechanical-resistant design. New Zealand and South African standards have adopted various theoretical approaches to describe such behaviour in stainless steels. With respect to the building industry, describing the tensile behaviour of steel rebar used to produce reinforced concrete structures is of interest. Differences compared with the homogenous material described in the above mentioned standards and related literatures are discussed in this paper. Specifically, the presence of ribs and the TEMPCORE® technology used to produce carbon steel rebar may alter the elastoplastic model. Carbon steel rebar is shown to fit a Hollomon model giving hardening exponent values on the order of 0.17. Austenitic stainless steel rebar behaviour is better described using a modified Rasmussen model with a free fitted exponent of 6. Duplex stainless steel shows a poor fit to any previous model. [Spanish] Uno de los principales factores tenidos en cuenta en la fabricación de aceros estructurales es su comportamiento durante la fase elastoplástica o de endurecimiento por deformación. Normas neozelandesas y sudafricanas plantean diversas aproximaciones teóricas para describir dicho comportamiento en el caso de los aceros inoxidables. En el campo de la construcción resulta de interés la descripción del comportamiento tenso-deformacional de los aceros corrugados utilizados en las estructuras de hormigón armado. En este artículo se discuten los modelos planteados en las normas citadas anteriormente así como los existentes en la literatura tanto para los aceros corrugados inoxidables como para los aceros al carbono fabricados mediante el proceso denominado TEMPCORE® Los aceros TEMPCORE® analizados arrojan un valor del exponente de endurecimiento por deformación según el modelo de Hollomon de 0.17. Los aceros inoxidables austeníticos se ajustan mejor al modelo

RESISTENCIA A LA CORROSIÓN DE LAS MULTICAPAS DE [TIN/ALTIN]n DEPOSITADAS SOBRE ACERO AL CARBONO AISI 1045

Directory of Open Access Journals (Sweden)

WILLIAM APERADOR

2011-01-01

Full Text Available En este artículo se presenta el mejoramiento frente a la corrosión de los recubrimientos multicapas de [TiN/AlTiN]n con periodos de 2, 6, 12 y 24 bicapas depositados mediante la técnica de PVD magnetrón Sputtering sobre acero al carbono AISI 1045. La evaluación electroquímica se realizó mediante las técnicas espectroscopia de impedancia electroquímica (EIS y curvas de polarización Tafel, en una solución de 0.5M de H2SO4 + 3.5% wt. de NaCl. La resistencia a la corrosión aumentó de forma gradual en función del número de bicapas en comparación al sustrato encontrando valores de velocidad de corrosión de 18.51 mpy para el sustrato sin recubrir y de 1x10 6 mpy para la muestra con 24 bicapas. Los resultados electroquímicos revelan el efecto positivo en cuanto a la protección superficial del acero 1045 con el incremento del periodo en las multicapas de [TiN /AlTiN]n.

Alternativa de protección contra la corrosión del acero AISI 310S mediante recubrimiento de aluminio bajo condiciones de platos separadores en celdas de combustible de carbonatos fundidos

Directory of Open Access Journals (Sweden)

R. Orozco-Cruz

2016-01-01

Full Text Available Introducción: La celda de combustible de carbonatos fundidos (MCFC, por sus siglas en inglés convencional opera a 650°C. Consiste de un cátodo de NiO poroso y litiado, una mezcla eutéctica de carbonato de litio (Li2CO3 y carbonato de potasio (K2CO3 fundido en una matriz electrolitica de óxido de aluminio litiado (LiAlO2 y un ánodo poroso de Ni. Los platos separadores entre cada celda presentan problemas de corrosión. Ante eso, un acero inoxidable AISI 310S con recubrimiento fue estudiado en condiciones de un plato separador en una MCFC. Método: Se utilizó un acero inoxidable AISI 310S como sustrato (muestra A, aplicándole un recubrimiento de Al con (B y sin tratamiento térmico (C. Fueron expuestos en carbonatos fundidos (62 mol% Li2CO3 -38 mol% K2CO3 a 650 °C en crisoles de alúmina. El comportamiento electroquímico fue estudiado mediante la técnica de Espectroscopía de Impedancia Electroquimica (EIS. Para el análisis de los diagramas de impedancia, se utilizó el software de simulación “Boukamp Equivalent Circuit”. La sección transversal de las muestras corroídas fue caracterizada mediante Microscopía Electrónica de Barrido (SEM, por sus siglas en inglés y los productos formados por Difracción de rayos X (XRD, por sus siglas en inglés. Resultados: Los diagramas de EIS presentan aumentos y disminuciones en los semicírculos formados a altas frecuencias indicativo de disolución de la capa externa, aumento y disminución de la resistencia de esta última así como el posible rompimiento de ella. La técnica de XRD presentó fases LiFeO2, LiCrO2, -LiAlO2 y -LiAlO2 así como fases intermetálicas para las distintas condiciones de la muestra. De la misma manera, los análisis de SEM presentaron los espesores de cada una de las capas formadas. Discusión o Conclusión: En la muestra A, se formaron capas de LiFeO2 y LiCrO2 después de 200 horas de exposición. La capa de LiCrO2 aumenta por la difusión de Li hacia el

Strain hardening behavior and microstructural evolution during plastic deformation of dual phase, non-grain oriented electrical and AISI 304 steels

Energy Technology Data Exchange (ETDEWEB)

Soares, Guilherme Corrêa; Gonzalez, Berenice Mendonça; Arruda Santos, Leandro de, E-mail: leandro.arruda@demet.ufmg.br

2017-01-27

Strain hardening behavior and microstructural evolution of non-grain oriented electrical, dual phase, and AISI 304 steels, subjected to uniaxial tensile tests, were investigated in this study. Tensile tests were performed at room temperature and the strain hardening behavior of the steels was characterized by three different parameters: modified Crussard–Jaoul stages, strain hardening rate and instantaneous strain hardening exponent. Optical microscopic analysis, X-ray diffraction measurements, phase quantification by Rietveld refinement and hardness tests were also carried out in order to correlate the microstructural and mechanical responses to plastic deformation. Distinct strain hardening stages were observed in the steels in terms of the instantaneous strain hardening exponent and the strain hardening rate. The dual phase and non-grain oriented steels exhibited a two-stage strain hardening behavior while the AISI 304 steel displayed multiple stages, resulting in a more complex strain hardening behavior. The dual phase steels showed a high work hardening capacity in stage 1, which was gradually reduced in stage 2. On the other hand, the AISI 304 steel showed high strain hardening capacity, which continued to increase up to the tensile strength. This is a consequence of its additional strain hardening mechanism, based on a strain-induced martensitic transformation, as shown by the X-ray diffraction and optical microscopic analyses.

Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Gales, Gregoire [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France)]|[DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Roy, Marc; Feron, Damien [DEN/DPC/SCCME/LECA, Bat 458, CEA Saclay F- 91191 Gif sur Yvette (France); Libert, Marie-Francoise; Sellier, Regine [DTN/SMTM/LMTE, CEA Cadarache, F-13108 Saint-Paul-lez-Durance (France); Cournac, Laurent [DSV/DEVM/LEP, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France); Heulin, Thierry [DSV/DEVM/LEMIR, UMR 6191 CNRS-CEA-Universite Aix-Marseille II, CEA Cadarache, F- 13108 Saint-Paul-lez-Durance (France)

2004-07-01

Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O{sub 2}{sup -}) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H{sub 2} commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

Action of an aerobic hydrogenotroph bacteria isolated from ultrapure water systems on AISI 304 stainless steel

International Nuclear Information System (INIS)

Gales, Gregoire; Roy, Marc; Feron, Damien; Libert, Marie-Francoise; Sellier, Regine; Cournac, Laurent; Heulin, Thierry

2004-01-01

Several microbial studies have been recently performed in nuclear power stations. These studies concerned essentially the formation of bio-films on submerged metal coupons. Heterotrophic micro-organisms have been found in bulk water of nuclear fuel storage basins but the in situ nutrient sources for bacterial development in such highly oligo-trophic water was unknown. In nuclear environments, radiations lead to the production of molecular hydrogen, hydrogen peroxide and some radicals (OH, O 2 - ) by radiolysis of water or embedding matrices. Bacterial oxidation of molecular H 2 commonly occurs in nature, as molecular hydrogen represents a high-energy reductant. We investigated the microbiology of a ultra-pure water basin containing irradiating waste. The initial aim of this study was to determine if autotrophic bacterial growth was possible in this basin. A major bacteria was isolated (Ralstonia sp. GGLH002) which was able to grow autotrophically with hydrogen as the electron donor and oxygen as the electron acceptor, and heterotrophically with organic nutrients. Its hydrogenase activity has been characterized. We focused then our study on the effects of this strain on 304L AISI stainless steel depending on the nutrient source used for bacterial development, e.g hydrogen or organics. In conclusion, the mechanism of passivation enhanced by Ralstonia sp. GGLH002 on AISI 304L SS still remains unknown. Several techniques could give substantial information, including XPS and polarization curves. It seems for the moment that the major bacteria inhabiting an oxic environment containing hydrogen due to radiolysis is not aggressive to stainless steel in conditions near from its environment. Further investigations are needed to test this hypothesis, including a study of the molecular diversity of the bacteria using culture-independent techniques, as cultivatable bacterial populations represent in general only a fraction of the total bacteria. (authors)

Microestructura y propiedades de capas de tribaloy T-800 depositadas mediante plaqueado láser

Directory of Open Access Journals (Sweden)

Navas, C.

2004-04-01

Full Text Available The present work is based on obtaining Co based coatings (Tribaloy T-800 on plates of 18/8 stainless steel (AISI 304 by laser cladding technique. After the treatment, samples were characterized by optical and scanning electron microscopy with EDS analysis. The elemental composition of the coating was determined with a glow discharge lamp spectrometer (GDL. The study of the interface revealed a good adherence between the substrate and coating without substantial defects. For the laser cladded coatings, the microstructure was dendritic with a high degree of refinement and chemical homogeneity close to the original powder. The grain coarsening was observed in the overlapping zones due to the second heat treatment. Microhardness of the coatings reached 750 HV, a considerably higher value than the substrate hardness (200 HV. Also, the coating corrosion resistance in saline solutions had a great improvement.

El presente trabajo se centra en la obtención de capas de aleación base Cobalto (Tribaloy T-800 sobre un sustrato de acero inoxidable 18/8 (AISI 304 mediante la técnica de plaqueado láser. Tras los tratamientos, se caracterizaron las probetas mediante microscopía óptica y electrónica de barrido con microanálisis (EDS. La composición elemental del recubrimiento se determinó en un espectrómetro de emisión óptica con fuente de excitación (GDL. El estudio de la interfase reveló una perfecta adherencia entre el recubrimiento y el material base, sin defectos apreciables. La microestructura de las capas depositadas es dendrítica con un alto grado de refinamiento y una homogeneidad química a lo largo del cordón y con valores muy próximos a los del polvo de partida. En las zonas de solape entre cordones, se observó un crecimiento del grano debido al segundo tratamiento térmico recibido. La microdureza de las capas alcanza los 750 HV, valor considerablemente superior al del sustrato (200 HV. Asimismo, se obtuvo una mejora

Recubrimientos de (ti,aln sobre acero aisi 4140 por sputtering reactivo

Directory of Open Access Journals (Sweden)

DANNA GARCIA

2007-01-01

Full Text Available Empleando la técnica de Pulverización catódica con radiofrecuencia y magnetrón (Magnetron Sputtering RF, se prepararon películas de (Ti,AlN sobre sustratos de acero AISI 4140. Se utilizó un blanco formado con polvos metálicos de Ti y Al, con composición nominal 60% Ti y 40% Al (porcentaje en átomos y una razón de presiones parciales de nitrógeno - argón, PN2/PAr de 0,1 aproximadamente; la temperatura del sustrato se varió entre 260 y 330 ºC y el tiempo de deposición entre 2 y 4,5 horas para obtener películas con diferentes espesores. La composición química de las películas se determinó mediante la técnica de energía dispersada de rayos X (EDX, y su topografía mediante microscopía de fuerza atómica (AFM. Igualmente se midió micro dureza, y se determinó su comportamiento electroquímico mediante espectroscopia de impedancia electroquímica EIS y ensayos TAFEL. Las películas obtenidas presentaron granos globulares, uniformes y de pequeño diámetro, con características electroquímicas de protección al sustrato frente a procesos de corrosión.

Use of Direct Current Resistivity Measurements to Assess AISI 304 Austenitic Stainless Steel Sensitization

OpenAIRE

Mesquita, Ramaiany Carneiro; Mecury, José Manoel Rivas; Tanaka, Auro Atsumi; Sousa, Regina Célia de

2015-01-01

This paper describes the feasibility of using direct current electrical resistivity measurements to evaluate AISI 304 austenitic stainless steel sensitization. ASTM A262 – Practice A and double loop electrochemical potentiodynamic reactivation (DL-EPR) tests were performed to assess the degree of sensitization (DoS) qualitatively and quantitatively, and electrical resistivity (ER) was measured by the four-point direct-current potential drop method. The results indicate that the DoS incr...

High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

International Nuclear Information System (INIS)

Prajitno, Djoko Hadi; Syarif, Dani Gustaman

2014-01-01

The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO 2 . The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe 2 O 3 . Minor element such as Cr 2 O 3 is also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO 2 appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate

Passivation of duplex stainless steel in solutions simulating chloride-contaminated concrete

Directory of Open Access Journals (Sweden)

Takenouti, H.

2007-12-01

Full Text Available Most studies published to date on the corrosion behaviour of stainless reinforcing steel are based on austenitic steel. The market presence of corrugated duplex steel is growing, however. The present study compared passivity in 2205 type duplex and 304 type austenitic stainless steel. Polarization tests in chloride-containing Ca(OH2 solutions confirmed the exceptional performance of duplex steels. X-ray photoelectronic spectroscopy (XPS showed that the passive layer generated on duplex stainless steel in media simulating concrete pore solutions had a higher Cr content than the layer formed on steel in contact with the air. The XPS results also revealed that in duplex steel the form adopted by the passive layer Fe oxides was Fe3O4 in the solutions simulating concrete, rather than Fe2O3, as in duplex steel exposed to air. Electrochemical impedance spectroscopy (EIS can be used to monitor the transformations taking place in the passive layer and analyze the factors involved.La mayoría de los estudios publicados hasta el momento sobre el comportamiento frente a la corrosión de armaduras de acero inoxidable se basan en aceros austeníticos. Sin embargo, la presencia en el mercado de aceros corrugados dúplex es cada vez más importante. En este trabajo se analiza la pasividad de un acero inoxidable dúplex tipo 2205 en comparación con la de un inoxidable austenítico tipo 304. Los ensayos de polarización en disoluciones de Ca(OH2 con cloruros confirman el excepcional comportamiento de los aceros dúplex. La espectroscopía fotoelectrónica de rayos X (XPS informa de que la capa pasiva generada en aceros inoxidables dúplex en medios que simulan la disolución de los poros del hormigón posee mayor contenido en óxidos de Cr que la formada en aire. También se puede deducir de los resultados de XPS que los óxidos de Fe de la capa pasiva de los aceros dúplex se encuentran en forma de Fe3O4 en las disoluciones que simulan el hormigón en vez de en

Caracterización mediante HRTEM de un acero AISI4140 nitrurado por postdescarga micro-ondas

Directory of Open Access Journals (Sweden)

Béjar-Gómez, L.

2005-12-01

Full Text Available An analysis of the nitrides formed in an AISI 4140 steel nitrided by postdischarge microwave nitriding treatment was carried out by high resolution transmission electron microscopy (HRTEM, fast Fourier transform (FFT and nanoanalysis. The steel samples were nitrided below of the eutectoid transformation point (590 °C, after nitriding the samples were cooling slowly inside in the reactor whit an argon atmosphere. The analysis were carried out in a FEG-TEM PHILIPS TECNAI F20 at 200 Kv. The results showed the morphology and size of the nitrides ε-Fe_2-3N and γ’-Fe₄N, which had coherency whit the matrix. By other hand the following crystallographic relations were determined: (110 Fe-α ║ (1001 ε-Fe_2-3N ║ (110 γ’-Fe₄N and [1-1 0]Fe-α ║ [1 0-1 0] ε-Fe_2-3N ║ [0 1 1] Fe₄N.

Un análisis de las fases de nitruros formados en un acero AISI 4140, nitrurado mediante condiciones de postdescarga micro-ondas, se llevó a cabo por microscopía electrónica de transmisión de alta resolución (HRTEM, rápida transformada de Fourier (FFT y nanoanálisis. Las muestras de acero fueron nitruradas por debajo del punto de transformación eutectoide (590 °C; después del tratamiento de nitruración las piezas fueron enfriadas lentamente dentro del reactor con una atmósfera de argón. Los análisis se realizaron en un microscopio Philips con cañón de emisión de campo Tecnai F20 a 200 Kv (PHILIPS FEG-TEM TECNAI F20. Los resultados mostraron la morfología y tamaño de los nitruros de hierro ε-Fe_2-3N y γ’-Fe₄N, los cuáles mostraron coherencia con la matriz. Además, se obtuvo la siguiente relación de coherencia entre precipitados y matriz: (110 Fe-α ║ (1001 ε-Fe_2-3N ║ (110 γ’-Fe₄N y [1-1 0]Fe-α ║ [1 0-1 0] ε-Fe_2-3N ║ [0 1 1] Fe₄N.

Effect of temperature on the level of corrosion caused by heavy petroleum on AISI 304 and AISI 444 stainless steel

Directory of Open Access Journals (Sweden)

João Paulo Sampaio Eufrásio Machado

2006-06-01

Full Text Available This work presents a study on the influence of national heavy petroleum in the corrosion of the AISI 444 and AISI 304 stainless steels in simulated refining operation conditions. The petroleum was first characterized through physicochemical analysis (density, fluidity point, viscosity, sulfur concentration. In an attempt to understand the corrosion effect of temperature and of the type of heating the referred types of steel thermal treatments were carried out at three levels of temperature (200, 300 and 400 °C. The procedure was done in conditions close to those in the distillation column. Heat was gradually increased from room temperature, and directly heated to working temperature. Each treatment took 4 hours to be completed. Scanning electronic microscopy (SEM and the analysis of X rays dispersive energy (EDX were used after the trials to characterize the samples. The results show that treatment temperature, as well as the type of heating, has distinct influences on each type of steel.

termodinámico en placas de acero AISI 4140 y pistas de rodamiento utilizando adhesivos anaeróbicos

Directory of Open Access Journals (Sweden)

Germán García

2006-01-01

Full Text Available Se evaluó el trabajo de adhesión termodinámico de placas planas de acero (AISI 4140 y AISI 52100 en contacto con dos adhesivos anaeróbicos de uso comercial, mediante la medición de los ángulos de contacto termodinámico de avance y retroceso obtenidos por el método de inmersión y emersión. Se utilizó el método de van Oss para calcular las componentes polares y no polares de adhesión para cada par metal-adhesivo. Se analizó también el efecto de la aplicación de un activador de superficie sobre el trabajo de adhesión en húmedo y se relacionaron los resultados con las características químicas y físicas de las placas. Los resultados indicaron que la aplicación del activador tuvo un efecto importante sobre la mojabilidad de los adhesivos, pero pequeña influencia en el trabajo de adhesión medido. Por otro lado, se encontraron diferencias importantes en la respuesta de los dos adhesivos estudiados, fundamentalmente en virtud de su composición química y propiedades reológicas.

Gas tungsten arc welding and friction stir welding of ultrafine grained AISI 304L stainless steel: Microstructural and mechanical behavior characterization

Energy Technology Data Exchange (ETDEWEB)

Sabooni, S., E-mail: s.sabooni@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Karimzadeh, F.; Enayati, M.H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of); Ngan, A.H.W. [Department of Mechanical Engineering, The University of Hong Kong, Pokfulam Road, Hong Kong (China); Jabbari, H. [Department of Materials Engineering, Isfahan University of Technology, 84156-83111 Isfahan (Iran, Islamic Republic of)

2015-11-15

In the present study, an ultrafine grained (UFG) AISI 304L stainless steel with the average grain size of 650 nm was successfully welded by both gas tungsten arc welding (GTAW) and friction stir welding (FSW). GTAW was applied without any filler metal. FSW was also performed at a constant rotational speed of 630 rpm and different welding speeds from 20 to 80 mm/min. Microstructural characterization was carried out by High Resolution Scanning Electron Microscopy (HRSEM) with Electron Backscattered Diffraction (EBSD) and Transmission Electron Microscopy (TEM). Nanoindentation, microhardness measurements and tensile tests were also performed to study the mechanical properties of the base metal and weldments. The results showed that the solidification mode in the GTAW welded sample is FA (ferrite–austenite) type with the microstructure consisting of an austenite matrix embedded with lath type and skeletal type ferrite. The nugget zone microstructure in the FSW welded samples consisted of equiaxed dynamically recrystallized austenite grains with some amount of elongated delta ferrite. Sigma phase precipitates were formed in the region ahead the rotating tool during the heating cycle of FSW, which were finally fragmented into nanometric particles and distributed in the weld nugget. Also there is a high possibility that the existing delta ferrite in the microstructure rapidly transforms into sigma phase particles during the short thermal cycle of FSW. These suggest that high strain and deformation during FSW can promote sigma phase formation. The final austenite grain size in the nugget zone was found to decrease with increasing Zener–Hollomon parameter, which was obtained quantitatively by measuring the peak temperature, calculating the strain rate during FSW and exact examination of hot deformation activation energy by considering the actual grain size before the occurrence of dynamic recrystallization. Mechanical properties observations showed that the welding

Nanosecond laser surface modification of AISI 304L stainless steel: Influence the beam overlap on pitting corrosion resistance

International Nuclear Information System (INIS)

Pacquentin, Wilfried; Caron, Nadège; Oltra, Roland

2014-01-01

Surface modifications of AISI 304L stainless steel by laser surface melting (LSM) were investigated using a nanosecond pulsed laser-fibre doped by ytterbium at different overlaps. The objective was to study the change in the corrosion properties induced by the treatment of the outer-surface of the stainless steel without modification of the bulk material. Different analytical techniques such as scanning electron microscopy (SEM), X-ray diffraction (XRD), and glow discharge optical emission spectrometry (GDOES) were used to characterize the laser-melted surface. The corrosion resistance was evaluated in a chloride solution at room temperature by electrochemical tests. The results showed that the crystallographic structure, the chemical composition, the properties of the induced oxide layer and consequently the pitting corrosion resistance strongly depend on the overlap rate. The most efficient laser parameters led to an increase of the pitting potential by more than 300 mV, corresponding to a quite important improvement of the corrosion resistance. This latter was correlated to chromium enrichment (47 wt.%) at the surface of the stainless steel and the induced absence of martensite and ferrite phases. However, these structural and chemical modifications were not sufficient to explain the change in corrosion behaviour: defects and adhesion of the surface oxide layer must have been taken into consideration.

Corrosion of AISI 304 stainless steel in polluted seawater

International Nuclear Information System (INIS)

Brankevich, G.; Guiamet, P.; Videla, H.A.

1987-01-01

The sequence of microbiofouling settlement on AISI 304 stain steel samples exposed to polluted harbor sea water of a power cooling water intake is studied. The firts sates of bacterial colonization are followed by means of scanning electron microscopy during two weeks of exposure. The relation between microbiofouling and corrosion is also followed by scanning electron microscopy and evaluated through electrochemical polarization experiments. The results obtained show that microbial colonization and extracellular polimeric substances forming the biofilms have a marked influence on the electrochemical behaviour of stainless steel in sea water. Laboratory experiments using inorganic chloride solutions or artificial sea water show a considerably lesser attack of the metal than those performed 'in situ' with natural sea water. Passivity breadown is highly facilitated when complex biological and inorganic deposits (fouling) have settled on the metal surface. (Author) [pt

High temperature oxidation behavior of austenitic stainless steel AISI 304 in steam of nanofluids contain nanoparticle ZrO2

Energy Technology Data Exchange (ETDEWEB)

Prajitno, Djoko Hadi, E-mail: djokohp@batan.go.id; Syarif, Dani Gustaman, E-mail: djokohp@batan.go.id [Research Center for Nuclear Materials and Radiometry, Jl. Tamansari 71, Bandung 40132 (Indonesia)

2014-03-24

The objective of this study is to evaluate high temperature oxidation behavior of austenitic stainless steel SS 304 in steam of nanofluids contain nanoparticle ZrO{sub 2}. The oxidation was performed at high temperatures ranging from 600 to 800°C. The oxidation time was 60 minutes. After oxidation the surface of the samples was analyzed by different methods including, optical microscope, scanning electron microscope (SEM) and X-ray diffraction (XRD). X-ray diffraction examination show that the oxide scale formed during oxidation of stainless steel AISI 304 alloys is dominated by iron oxide, Fe{sub 2}O{sub 3}. Minor element such as Cr{sub 2}O{sub 3} is also appeared in the diffraction pattern. Characterization by optical microscope showed that cross section microstructure of stainless steel changed after oxidized with the oxide scale on the surface stainless steels. SEM and x-ray diffraction examination show that the oxide of ZrO{sub 2} appeared on the surface of stainless steel. Kinetic rate of oxidation of austenite stainless steel AISI 304 showed that increasing oxidation temperature and time will increase oxidation rate.

Structure and properties of the Stainless steel AISI 316 nitrided with microwave plasma; Estructura y propiedades del acero inoxidable AISI 316 nitrurado con plasmas de microondas

Energy Technology Data Exchange (ETDEWEB)

Becerril R, F

1999-07-01

In this work were presented the results obtained by nitridation on stainless steel AISI 316 using a plasma generated through a microwave discharge with an external magnetic field using several moistures hydrogen / nitrogen to form a plasma. The purpose of nitridation was to increase the surface hardness of stainless steel through a phase formation knew as {gamma}N which has been reported that produces such effect without affect the corrosion resistance proper of this material. (Author)

Microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steel

International Nuclear Information System (INIS)

Park, Ji Yoon; Kim, Kwan Hyu; Choe, Han Cheol

1999-01-01

The microstructure and mechanical properties of Ti/TiN film coated on AISI 304 stainless steels have been studied. AISI 304 stainless steels containing 0.1∼1.0 wt% Ti were fabricated by using vacuum furnace and followed by solutionization treatment at 1050 .deg. C for 1hr. The specimens were coated by Ti and TiN with 1 μm and 2 μm thickness by electron-beam PVD method. The microstructure and phase analysis were carried out by using XRD, WDS and SEM. Mechanical properties such as hardness (micro-Vickers) and wear resistance were examined. Coated films showed fine columnar structure and some defects. Surface roughness increased in all specimens after TiN coating. XRD patterns showed that the TiN(111) peak was major in TiN single-layer and the other peaks were very weak, but TiN(220) and TiN(200) peaks were developed in Ti/TiN double-layer. The hardness of the coating film was higher in Ti/TiN double-layer than in TiN single-layer and not affected by the Ti content of substrate. Ti/TiN double-layer showed better wear resistance than TiN single-layer. The observed wear traces were sheared type in all coated specimens

Effects of nitrogen and pulsed mean welding current in AISI 316 austenitic stainless steel solidification cracks; Efecto del nitrogeno y la corriente media pulsada de soldadura en la formacion de grietas de solidificacion en aceros inoxidables AISI 316L

Energy Technology Data Exchange (ETDEWEB)

Trevisan, R. E.; Braga, E.; Fals, H. C.

2002-07-01

An analysis of the influence of nitrogen concentration in the weld zone and the pulsed mean welding current in the solidification crack formation is presented in this paper. The AISI 316L austenitic stainless steel was employed as the metal base. The welding was done using CC+ pulsed flux cored are welding process and AWS E316L wire type. The tests were conducted using CO{sub 2} shielding gas with four different nitrogen levels (0,5; 10 and 15%) in order to induce different nitrogen weld metal concentrations. The pulsed mean welding current was varied in three levels and the. Transvarestraint tangential strain test was fixed of 5%. The results showed that the solidification cracking decreased as the pulsed mean welding current increase. It was also verified that an increase of the weld zone nitrogen level was associated with a decrease in both the total length of solidification crack and the amount of {delta} ferrite. (AUthor) 20 refs.

PROTECCIÓN CONTRA LA CORROSIÓN POR SALES FUNDIDAS DE UN ACERO AL CARBONO POR ROCIADO TERMICO

OpenAIRE

JOSE MARULANDA; ANDRÉS GARCÍA; JOSE VITOLA

2009-01-01

Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono rociado térmicamente con una aleación de acero inoxidable, en una mezcla de sal con 20% Na2SO4 - 80% V2O5, entre 700ºC - 850ºC. Los resultados de las pruebas gravimétricas mostraron una deficiente protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento protector, debido a que las temperaturas de exposición fueron mayores que las temperaturas de fusión de...

Effect of welding process, type of electrode and electrode core diameter on the tensile property of 304L austenitic stainless steel

Directory of Open Access Journals (Sweden)

Akinlabi OYETUNJI

2014-11-01

Full Text Available The effect of welding process, type of electrode and electrode core diameter on the tensile property of AISI 304L Austenitic Stainless Steel (ASS was studied. The tensile strength property of ASS welded samples was evaluated. Prepared samples of the ASS were welded under these three various variables. Tensile test was then carried out on the welded samples. It was found that the reduction in ultimate tensile strength (UTS of the butt joint samples increases with increase in core diameter of the electrode. Also, the best electrode for welding 304L ASS is 308L stainless steel-core electrode of 3.2 mm core diameter. It is recommended that the findings of this work can be applied in the chemical, food and oil industries where 304L ASS are predominantly used.

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo,Carlos Eduardo; Tschiptschin,André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% c...

Low temperature plasma carburizing of AISI 316L austenitic stainless steel and AISI F51 duplex stainless steel

OpenAIRE

Pinedo, Carlos Eduardo; Tschiptschin, André Paulo

2013-01-01

In this work an austenitic AISI 316L and a duplex AISI F51 (EN 1.4462) stainless steel were DC-Plasma carburized at 480ºC, using CH4 as carbon carrier gas. For the austenitic AISI 316L stainless steel, low temperature plasma carburizing induced a strong carbon supersaturation in the austenitic lattice and the formation of carbon expanded austenite (γC) without any precipitation of carbides. The hardness of the carburized AISI 316L steel reached a maximum of 1000 HV due to ∼13 at% carbon super...

Problemas en la reparación por laser cladding de superficies de acero AISI D2 tratado térmicamente

Directory of Open Access Journals (Sweden)

Busquets, D.

2010-08-01

microscopia óptica, microscopía electrónica de barrido (MEB y difracción de electrones retrodispersados (EBSD. El objetivo del trabajo es relacionar los parámetros del proceso de recubrimiento por láser (potencia, velocidad, caudal de polvo con las transformaciones metalúrgicas producidas en el acero de herramienta AISI D2, con el fin de optimizar las condiciones de operación durante la reparación. Los resultados muestran que los parámetros influyen en gran medida en la geometría del cordón y en la formación de la microestructura. Aunque es sencillo obtener deposiciones geométricamente aceptables (forma y tamaño adecuado, ausencia de porosidad, en muchos casos aparecen fenómenos perjudiciales como la dilución de carburos y la aparición de fases metaestables que modifican las propiedades mecánicas del recubrimiento. En concreto, la presencia de austenita retenida en el recubrimiento, relacionada con la temperatura máxima alcanzada y la velocidad de enfriamiento, produce una fuerte disminución en la dureza, que debe evitarse. Además, para una misma composición y acabado superficial, el estado metalúrgico inicial del sustrato tiene una gran influencia sobre el resultado. Sustratos en estado de temple implican una mayor absorción del láser y la acumulación de calor que produce mayores zonas afectadas por el calor (ZAC. Por ese motivo, deben optimizarse los parámetros del proceso para cada operación de manera que se mejore el comportamiento en servicio del componente.

Characterization of welding of AISI 304l stainless steel similar to the core encircling of a BWR reactor

International Nuclear Information System (INIS)

Gachuz M, M.E.; Palacios P, F.; Robles P, E.F.

2003-01-01

Plates of austenitic stainless steel AISI 304l of 0.0381 m thickness were welded by means of the SMAW process according to that recommended in the Section 9 of the ASME Code, so that it was reproduced the welding process used to assemble the encircling of the core of a BWR/5 reactor similar to that of the Laguna Verde Nucleo electric plant, there being generated the necessary documentation for the qualification of the one welding procedure and of the welder. They were characterized so much the one base metal, as the welding cord by means of metallographic techniques, scanning electron microscopy, X-ray diffraction, mechanical essays and fracture mechanics. From the obtained results it highlights the presence of an area affected by the heat of up to 1.5 mm of wide and a value of fracture tenacity (J IC ) to ambient temperature for the base metal of 528 KJ/m 2 , which is diminished by the presence of the welding and by the increment in the temperature of the one essay. Also it was carried out an fractographic analysis of the fracture zone generated by the tenacity essays, what evidence a ductile fracture. The experimental values of resistance and tenacity are important for the study of the structural integrity of the encircling one of the core. (Author)

EVALUACIÓN EXPERIMENTAL DE LA RESISTENCIA A LA CORROSIÓN DE UN ACERO AISI-SAE 4140 IMPLANTADO CON IONES DE NITRÓGENO

Directory of Open Access Journals (Sweden)

DARIO PEÑA

2009-01-01

Full Text Available Se estudió la resistencia a la corrosión de un acero AISI-SAE 4140 implantado con iones de Nitrógeno mediante la técnica 3DII (Implantación Iónica Tridimensional. Se evaluaron diferentes rugosidades de las muestras implantadas mediante técnicas electroquímicas de Rp, EIS y Tafel en una salmuera al 3% de NaCl, donde se obtuvo la mayor resistencia a la corrosión para el material implantado con menor rugosidad. Se produjo la formación de una posible capa protectora estable con la inmersión de las muestras en el electrolito de trabajo para tiempos superiores a 240 horas.

Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process

OpenAIRE

Alves, Eder Paduan; Piorino Neto, Francisco; An, Chen Ying

2010-01-01

Abstract: The purpose of this work was to assess the development of solid state joints of dissimilar material AA1050 aluminum and AISI 304 stainless steel, which can be used in pipes of tanks of liquid propellants and other components of the Satellite Launch Vehicle. The joints were obtained by rotary friction welding process (RFW), which combines the heat generated from friction between two surfaces and plastic deformation. Tests were conducted with different welding process parameters. The ...

Resistencia al desgaste de recubrimientos Fe-Nb-Cr-W, Nb, AISI 1020 y AISI 420 producidos por proyección térmica por arco eléctrico

Directory of Open Access Journals (Sweden)

López-Covaleda, E. A.

2013-10-01

Full Text Available The commercial materials 140MXC (with iron, tungsten, chrome, niobium, 530AS (AISI 1015 steel and 560AS (AISI 420 steel on AISI 4340 steel were deposited using thermal spray with arc. The aim of work was to evaluate the best strategy abrasive wear resistance of the system coating-substrate using the following combinations: (1 homogeneous coatings and (2 coatings depositing simultaneously 140MXC + 530AS and 140MXC + 560AS. The coatings microstructure was characterized using Optical microscopy, Scanning electron microscopy and Laser confocal microscopy. The wear resistance was evaluated through dry sand rubber wheel test (DSRW. We found that the wear resistance depends on the quantity of defects and the mechanical properties like hardness. For example, the softer coatings have the biggest wear rates and the failure mode was characterized by plastic deformation caused by particles indentation, and the other hand the failure mode at the harder materials was grooving. The details and wear mechanism of the coatings produced are described in this investigation.Mediante proyección térmica de arco eléctrico fueron depositados tres materiales comercialmente conocidos como: 140MXC (a base de hierro, wolframio, cromo y niobio, 530AS (acero AISI 1020 y 560AS (acero AISI 420, sobre acero AISI 4340. Con el objetivo de evaluar la mejor estrategia para incrementar la resistencia al desgaste abrasivo, los recubrimientos fueron depositados de dos formas: (1 monocapas homogéneas de cada material y (2 recubrimientos depositando con alambres disimiles de 140MXC + 530AS y 140MXC + 560AS. Los recubrimientos fueron caracterizados microestructuralmente mediante Difracción de rayos X, Microscopía óptica, Microscopía láser confocal y Microscopía electrónica de barrido. La evaluación de la resistencia al desgaste abrasivo se realizó mediante ensayo con arena seca y rueda de caucho (DSRW. Se encontró que la resistencia al desgaste depende entre otras de las

Impact of structure and morphology of nanostructured ceria coating on AISI 304 oxidation kinetics

Science.gov (United States)

Aadhavan, R.; Suresh Babu, K.

2017-07-01

Nanostructured ceria-based coatings are shown to be protective against high-temperature oxidation of AISI 304 due to the dynamics of oxidation state and associated defects. However, the processing parameters of deposition have a strong influence in determining the structural and morphological aspects of ceria. The present work focuses on the effect of variation in substrate temperature (50-300 °C) and deposition rate (0.1-50 Å/s) of ceria in electron beam physical vapour evaporation method and correlates the changes in structure and morphology to high-temperature oxidation protection. Unlike deposition rate, substrate temperature exhibited a profound influence on crystallite size (7-18 nm) and oxygen vacancy concentration. Upon isothermal oxidation at 1243 K for 24 h, bare AISI 304 exhibited a linear mass gain with a rate constant of 3.0 ± 0.03 × 10-3 kg2 m-4 s-1 while ceria coating lowered the kinetics by 3-4 orders. Though the thickness of the coating was kept constant at 2 μm, higher deposition rate offered one order lower protection due to the porous nature of the coating. Variation in the substrate temperature modulated the porosity as well as oxygen vacancy concentration and displayed the best protection for coatings deposited at moderate substrate temperature. The present work demonstrates the significance of selecting appropriate processing parameters to obtain the required morphology for efficient high-temperature oxidation protection.

“ESTUDIO DE CORROSIÓN DE LOS ACEROS DÚPLEX 2205, AISI 1018 Y LA UNIÓN SOLDADA, EN UN DIGESTOR PARA LA FABRICACIÓN DE PAPEL”

OpenAIRE

Vázquez Navarro, Brenda Alondra

2012-01-01

El presente trabajo, se realizó en el laboratorio del departamento de corrosión, del Instituto de Investigaciones Metalúrgicas, de la Universidad Michoacana de San Nicolás de Hidalgo. Se estudió la corrosión en el digestor de cocción continua modificada, que se ubica en la planta de papel de la Corporación Scribe en la Ciudad de Morelia, Michoacán. El digestor en estudio, está fabricado principalmente de acero al carbono AISI 1018. En la zona media inferior de este equipo, p...

Study of discordancy mobility in the AISI 304 steel

International Nuclear Information System (INIS)

Lima, L.F.C.P. de; Miranda, P.E.V. de; Monteiro, S.N.

1987-01-01

Internal Friction (IF), measurements were carried out in a type AISI 304 austenitic stainless steels at approximately 1HZ of frequency in the temperature interval from 120 to 573K. The IF spectra and the vibration frequency were obtained in samples were submitted to specific heat treatments. The results showed IF spectra with a well defined peak at 260K. The intensity dependes on the amount of plastic deformation previously introduced in the sample. Another broad peak was detected between 300 and 400K. Both peaks could only be detected after plastic deformation in uniaxial tension or torsion. In torsionably deformed samples at liquid nitrogen temperature, 77 K, the IF spectrum is observed only after linear annealing at 400K. This apparently results from a high damping due to a possible phase transformation which occurs around room temperature. The broad peak at higher temperature is sensitive to recovery induced by linear annealings. (Author) [pt

Evaluation of structural behaviour and corrosion resistant of austenitic AISI 304 and duplex AISI 2304 stainless steel reinforcements embedded in ordinary Portland cement mortars

International Nuclear Information System (INIS)

Medina, E.; Cobo, A.; Bastidas, D. M.

2012-01-01

The mechanical and structural behaviour of two stainless steels reinforcements, with grades austenitic EN 1.4301 (AISI 304) and duplex EN 1.4362 (AISI 2304) have been studied, and compared with the conventional carbon steel B500SD rebar. The study was conducted at three levels: at rebar level, at section level and at structural element level. The different mechanical properties of stainless steel directly influence the behaviour at section level and structural element level. The study of the corrosion behaviour of the two stainless steels has been performed by electrochemical measurements, monitoring the corrosion potential and the lineal polarization resistance (LPR), of reinforcements embedded in ordinary Portland cement (OPC) mortar specimens contaminated with different amount of chloride over one year time exposure. Both stainless steels specimens embedded in OPC mortar remain in the passive state for all the chloride concentration range studied after one year exposure. (Author) 26 refs.

Comparison of high temperature wear behaviour of plasma sprayed WC–Co coated and hard chromium plated AISI 304 austenitic stainless steel

International Nuclear Information System (INIS)

Balamurugan, G.M.; Duraiselvam, Muthukannan; Anandakrishnan, V.

2012-01-01

Highlights: ► WC–12wt.%Co powders were deposited to a thickness of 300 μm on to steel substrates. ► The micro hardness of the above coatings was lower than that of chromium plating. ► Wear resistance of chromium coating was increased up to five times of AISI 304 austenitic stainless steel. ► Wear resistance of chromium coat higher than plasma coat at different temperatures. -- Abstract: The wear behaviour of plasma sprayed coating and hard chrome plating on AISI 304 austenitic stainless steel substrate is experimentally investigated in unlubricated conditions. Experiments were conducted at different temperatures (room temp, 100 °C, 200 °C and 300 °C) with 50 N load and 1 m/s sliding velocity. Wear tests were carried out by dry sliding contact of EN-24 medium carbon steel pin as counterpart on a pin-on-disc wear testing machine. In both coatings, specimens were characterised by hardness, microstructure, coating density and sliding wear resistance. Wear studies showed that the hard chromium coating exhibited improved tribological performance than that of the plasma sprayed WC–Co coating. X-ray diffraction analysis (XRD) of the coatings showed that the better wear resistance at high temperature has been attributed to the formation of a protective oxide layer at the surface during sliding. The wear mechanisms were investigated through scanning electron microscopy (SEM) and XRD. It was observed that the chromium coating provided higher hardness, good adhesion with the substrate and nearly five times the wear resistance than that obtained by uncoated AISI 304 austenitic stainless steel.

Semiconducting properties of oxide and passive films formed on AISI 304 stainless steel and Alloy 600

Directory of Open Access Journals (Sweden)

Ferreira M. G. S.

2002-01-01

Full Text Available The semiconducting properties of passive films formed on AISI 304 stainless steel and Alloy 600 in borate buffer solution were studied by capacitance (Mott-Schottky approach and photocurrent measurements. Oxide films formed on 304 stainless steel in air at 350 ºC have also been studied. The results obtained show that, in all cases the electronic structure of the films is comparable to that of a p-n heterojunction in which the space charges developed at the metal-film and film-electrolyte interfaces have also to be considered. This is in accordance with analytical results showing that the oxide films are in all cases composed of an inner region rich in chromium oxide and an outer region rich in iron oxide.

Study of the M23C6 precipitation in AISI 304 stainless steel by small angle neutron scattering

International Nuclear Information System (INIS)

Boeuf, A.; Caciuffo, R.G.M.; Institut Max von Laue - Paul Langevin, 38 - Grenoble; Ancona Univ.; Melone, S.; Puliti, P.; Rustichelli, F.; Institut Max von Laue - Paul Langevin, 38 - Grenoble; Ancona Univ.; Coppola, R.

1985-01-01

The results of some small-angle neutron scattering (SANS) experiments on M 23 C 6 (M=Fe, Cr) carbide precipitation in AISI 304 stainless steel, aged at different temperatures during different times, are presented. The total volume fraction, the total surface of precipitates per unit sample volume and the size distribution functions of the M 23 C 6 carbides were determined. (orig.)

Efecto de los ciclos térmicos sobre la ZAT de una soldadura multipasos de un acero inoxidable superdúplex SAF 2507 Effect of thermal cycles on the HAZ of a stainless steel multipass weld of superduplex SAF 2507

Directory of Open Access Journals (Sweden)

D. Villalobos

2010-09-01

Full Text Available Los ciclos térmicos de una soldadura multipasos que experimenta un acero inoxidable superdúplex SAF 2507, pueden promover la precipitación de fases secundarias reduciendo significativamente las propiedades mecánicas y la resistencia a la corrosión. Debido a su aplicación en la industria petroquímica, el estudio de las aleaciones superdúplex es de suma importancia para predecir su comportamiento en servicio cuando están involucrados procesos de soldadura por arco eléctrico. En este trabajo, se estudia el cambio microestructural de la zona afectada térmicamente correspondiente al primer cordón depositado de una unión multipasos de acero inoxidable superdúplex SAF 2507 mediante el proceso GTAW y bajo tres temperaturas de interpasos. Los resultados muestran que la temperatura de interpasos tiene una influencia sobre la precipitación de fase sigma en la zona afectada térmicamente del primer cordón depositado.Thermal cycles experienced by a superduplex stainless steel SAF 2507 when is welded, can promote the precipitation of secondary phases which decrease the mechanical properties as well as the corrosion resistance. Due to the application of the duplex alloys in the petrochemical industry, the study of these alloys has become very important in order to predict its service behavior. The aim of this work is to study the microstructural changes in the superduplex stainless steel weld joint after applying the GTAW process under three interpass temperatures after the deposition of every single pass. The results showed that slow cooling rates promoted by the deposition of the subsecuent passes and the higher interpass temperature, promote the precipitation of sigma phase in the HAZ while rapid cooling rates promoted by the lower interpass temperature do not promote the sigma phase precipitation.

Influencia de la fase sigma en la laminación en frío de los aceros inoxidables dúplex

Directory of Open Access Journals (Sweden)

Fargas, G.

2004-04-01

Full Text Available One of the steps in the industrial rolling process of duplex stainless steels is the annealing heat treatment after hot rolling. If this annealing is performed in a temperature range that favours the precipitation of intermetallic phases, the mechanical properties can be modified considerably. The formation of these precipitates has a detrimental effect on the DSS ductility and toughness, so it will be a drawback for further cold rolling. In the present investigation, the effect of the sigma phase during cold rolling of a duplex stainless steel type EN 1.4462 has been studied. To simulate this process, compression tests up to a thickness reduction similar to that performed at industrial level have been done. The testing samples were studied by optical microscopy, SEM (scanning electronic microscopy and TEM (transmission electronic microscopy. Afterwards, some of the annealing conditions were selected in order to carry out cold rolling, using a laboratory scale machine, with the aim to observe if they offered a similar behaviour as that experienced in the compression tests. The results show that only the annealing condition at 975ºC during 10 minutes allows to produce sheets without rolling defects.

Una de las etapas en el proceso de fabricación industrial de los aceros inoxidables dúplex laminados es el tratamiento térmico de recocido posterior a la laminación en caliente. Si dicho recocido se efectúa en un rango de temperaturas que favorezca la formación de fases intermetálicas, las propiedades mecánicas del material pueden modificarse notablemente. La presencia en la microestructura bifásica de dichos precipitados provoca efectos muy perjudiciales sobre la ductilidad y la tenacidad del material, pudiendo llegar a hacer inviable la posterior etapa de laminación en frío. En el presente trabajo se ha estudiado el efecto sobre el proceso de laminación en frío de la presencia de fase sigma en un acero dúplex tipo E.N. 1

Zirconium oxide deposits (ZrO{sub 2}) and titanium oxide (TiO{sub 2}) on 304l stainless steel; Depositos de oxido de circonio (ZrO{sub 2}) y oxido de titanio (TiO{sub 2}) sobre acero inoxidable 304L

Energy Technology Data Exchange (ETDEWEB)

Davila N, M. L.

2015-07-01

This research project aims to carry out the surface and electrochemical characterization to obtain the optimum conditions of the hydrothermal deposits of zirconium oxide ZrO{sub 2} (baddeleyite) and titanium oxide TiO{sub 2} (anatase and rutile phases) on 304l stainless steel, simulating an inhibiting protective layer. 304l steel specimens were cut, pre-oxidized in water at a temperature of 288 degrees Celsius and 8 MPa, similar to those of a typical BWR conditions. From the titanium oxide anatase crystalline phase, the rutile phase was obtained by a heat treatment at 1000 degrees Celsius. The Sigma-Aldrich pre-oxidized powders and steel 304l were characterized using techniques of X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, chemical mapping and Raman spectrometry. The pre-oxidized steel has two oxide layers, an inner layer with nano metric crystals and another outer of larger crystals to 1μm, with the formation of hematite and magnetite, this predominating. The surface that contacted the sample holder has larger crystals. Hydrothermal deposits were carry out from suspensions of 10, 100 and 1000 ppm, of the crystal phases of anatase, rutile and baddeleyite, on the pre-oxidized steel at a temperature of 150 degrees Celsius for 2 and 7 days, samples were analyzed by X-ray diffraction, scanning electron microscopy, X-ray dispersive energy, Raman spectrometry and Tafel polarization. The suspension to 1000 ppm for 7 days coated surface most; the baddeleyite deposit is noticed more homogeneous than anatase and rutile. The deposit is favored when hematite and magnetite crystals are larger. The chemical mapping on deposits show that even after being immersed in water to 288 degrees Celsius during 30 days, the deposits are still present although a loss is observed. A reference electrode was assembled to conduct electrochemical tests of Tafel able to withstand a temperature of 288 degrees Celsius and pressure of 8 MPa. The baddeleyite deposit

The effects of strain induced martensite on stress corrosion cracking in AISI 304 stainless steel

International Nuclear Information System (INIS)

Lee, W. S.; Kwon, S. I.

1989-01-01

The effects of strain induced martensite on stress corrosion cracking behavior in AISI 304 stainless steel in boiling 42 wt% MgCl 2 solution were investigated using monotonic SSRT and cyclic SSRT with R=0.1 stress ratio. As the amount of pre-strain increased, the failure time of the specimens in monotonic SSRT test decreased independent of the existence of strain induced martensite. The strain induced martensite seems to promote the crack initiation but to retard the crack propagation during stress corrosion cracking

Caracterización de una nueva membrana cerámica de microfiltración con soporte de tejido en acero inoxidable flexible

Directory of Open Access Journals (Sweden)

Palacio, L.

1999-04-01

Full Text Available In this work we present the characterization of a ceramic flexible membrane, made by SynthesechemieⓇ, with a nominal pore size of 0.45 μm. This membrane consists in an α-alúmina porous support which has an embedded stainless steel metallic network, onto what a selective layer of titanium dioxide has been deposited. Membrane characterization has been realized with the aid of several techniques as: atomic force microscopy (AFM, air-liquid displacemente porosimetry and mercury porosimetry. Each tecnique giving information on different aspects: surface characteristics, bulk pores and active pores. Although the total pore size distribution is rather broad, the active pores (those opened to flux present a narrow distribution with a mean pore size very close to the manufacturer nominal value.

En este trabajo se ha abordado la caracterización de una membrana cerámica de microfiltración flexible, fabricada por SynthesechemieⓇ con tamaño de poro nominal de 0.45 μm. Ésta consiste en un soporte poroso de α-alúmina que posee un armazón formado por una red metálica de acero inoxidable sobre el cual existe una capa selectiva de óxido de titanio. La caracterización de la membrana ha sido realizada con diversas técnicas como: microscopia de fuerza atómica (AFM, porometría de desplazamiento aire-líquido y porosimetría de mercurio. Cada técnica da información sobre aspectos diferentes: superficie, poros totales y poros activos. Si bien la distribución total de tamaños de poro es bastante ancha, los poros activos (abiertos al flujo presentan una distribución de tamaños estrecha con un valor medio muy próximo al nominal.

Influence of ferritic phase on the localized corrosion in the AISI 304 type austenitic stainless steel

International Nuclear Information System (INIS)

Lombardi, C.C.M.; Ramanathan, L.V.

1994-01-01

The influence of adding up to 4.7 wt% Si to AISI 304 on the pitting corrosion resistance and intergranular corrosion resistance has been studied. The alloys were prepared by melting in a vacuum induction furnace and annealed at 1200 0 C for 1 hour followed by quenching. Prolonged immersion tests in Fe C L 3 and anodic polarization measurements in 3.5% NaCl revealed that with increasing Si the tendency of the alloy to pit decreased and the pitting potential increased. The susceptibility to intergranular corrosion as determined through Huey tests also decreased with Si content. The overall influence of Si in the alloy on the corrosion behaviour is considered to be due to incorporation of Si in the surface film and consequent improvement in adhesion as well as reduction in detects within the film. (author). 7 refs, 4 figs, 6 tabs

Efecto de la biopelícula en la corrosión de aceros inoxidables

Directory of Open Access Journals (Sweden)

Bethencourt, M.

2010-02-01

Full Text Available In this work, the influence of the biofilms in the corrosion process of different alloys of stainless steel was studied in two sampling points in a wastewater treatment plant during 4 years. The physicochemical microenvironment within the biofilms was characterized through O₂, H₂S and pH microelectrodes. Corrosion rates were quantified from the number, diameter and depth of pits. The results show a remarkable development of the biofilm and a significantly greater number of pits in the grit removal channel than in the sludge recirculation channel. Based on the characteristics of the water phase and microelectrode measurements, our results suggest that biofilms induced corrosion throughout 3 mechanisms: creation of differential aeration cells, areas with different pH and areas having high sulphide production which may react with metal ions.

En este trabajo se ha estudiado la influencia de las biopelículas en los procesos de corrosión de diferentes aleaciones de acero inoxidable, situadas durante 4 años en dos puntos de una estación depuradora de aguas residuales. Se caracterizó el microambiente físico-químico en el interior de las biopelículas mediante microelectrodos de O₂, H_2S y pH, y se cuantificaron las tasas de corrosión a partir del número, diámetro y profundidad de picadura. Los resultados obtenidos muestran un desarrollo más notable de las biopelículas y un número de picaduras significativamente mayor en el canal de salida de desbastes que en el canal de recirculación de fangos. Con base en las características del agua sobrenadante y en las medidas realizadas con microelectrodos, se sugiere que la biopelícula induce la corrosión a través de tres posibles mecanismos: creación de celdas de aireación diferencial, zonas con diferente pH y zonas con elevada producción de sulfuro capaz de reaccionar con iones metálicos.

Experimental Determination of Temperature During Rotary Friction Welding of AA1050 Aluminum with AISI 304 Stainless Steel

OpenAIRE

Alves, Eder Paduan; Piorino Neto, Francisco; An, Chen Ying; Silva, Euclides Castorino da

2012-01-01

Abstract: The purpose of this study was the temperature monitoring at bonding interface during the rotary friction welding process of dissimilar materiais: AA1050 aluminum with AISI 304 stainless steel. As it is directly related to the mechanical strenght of the junction, its experimental determination in real time is of fundamental importance for understanding and characterizing the main process steps, and the definition and optimization of parameters. The temperature gradients were obtained...

Effect of cold working and annealing on stress corrosion cracking of AISI 304 stainless steel

International Nuclear Information System (INIS)

Yeon, Y.M.; Kwun, S.I.

1983-01-01

A study was made of the effects of cold working and annealing on the stress corrosion cracking of AISI 304 stainless steel in boiling 42% MgCl 2 solution. When the 60% or 76% of yield stress was applied, the resistance to SCC showed maximum at 30% of cold work. However, when the same load was applied to the annealed specimens after cold working, the resistance to SCC decreased abruptly at 675degC annealing. The fracture mode changed mode change mixed → intergranular → transgranular as the amount of cold work increased. (Author)

Estimation of Fatigue Life of Laser Welded AISI304 Stainless Steel T-Joint Based on Experiments and Recommendations in Design Codes

DEFF Research Database (Denmark)

Lambertsen, Søren Heide; Damkilde, Lars; Kristensen, Anders Schmidt

2013-01-01

In this paper the fatigue behavior of laser welded T-joints of stainless steel AISI304 is investigated experimentally. In the fatigue experiments 36 specimens with a sheet thickness of 1 mm are exposed to one-dimensional cyclic loading. Three different types of specimens are adopted. Three groups...

Active flux tungsten inert gas welding of austenitic stainless steel AISI 304

Directory of Open Access Journals (Sweden)

D. Klobčar

2016-10-01

Full Text Available The paper presents the effects of flux assisted tungsten inert gas (A-TIG welding of 4 (10 mm thick austenitic stainless steel EN X5CrNi1810 (AISI 304 in the butt joint. The sample dimensions were 300 ´ 50 mm, and commercially available active flux QuickTIG was used for testing. In the planned study the influence of welding position and weld groove shape was analysed based on the penetration depth. A comparison of microstructure formation, grain size and ferrit number between TIG welding and A-TIG welding was done. The A-TIG welds were subjected to bending test. A comparative study of TIG and A-TIG welding shows that A-TIG welding increases the weld penetration depth.

Surface effects induced by cathodic hydrogenation in type AISI 304 stainless steel

International Nuclear Information System (INIS)

Silva, T.C.V.

1984-08-01

Cathodic hydrogen charging of type AISI 304 stainless steel modified its austenitic structure, giving rise to the formation of two new martensitic phases and the appearance of cracks, in most cases delayed. As electrolyte a 1 N H 2 S O 4 solution containing As 2 O 3 was employed. The cathodic hydrogenation was carries out at room temperature. The transformed phases were identified with black and white and coloured metallographic techniques, as well as by X-ray diffraction. The effect of cathodic hydrogenation in samples uniaxially tensile tested with constant nominal strain rate was investigated. It was concluded that the number of cracks per unit surface area changes with hydrogenation conditions and that hydrogen should be present for the embrittlement to occur. (author)

Aceros aluminotérmicos. Nuevas aplicaciones

Directory of Open Access Journals (Sweden)

Duart Blay, J. M.

2004-02-01

. Particular aplicación o interés presentan en la tecnología de los ferrocarriles para la obtención del carril continuo, prácticamente implantado en todo el mundo y en soldaduras cable de cobre-carril de acero empleadas en las señalizaciones para control de tráfico. En este trabajo se aportan las bases termodinámicas de la aluminotermia del hierro y su aplicación a la soldadura compleja de cruzamientos, juntas de dilatación y desvíos en FF.CC, que combinan aceros Hadfield, aceros inoxidables y aceros perlíticos de diferentes propiedades mecánicas. Las uniones deben ser compactas, resistentes y duras en los niveles que se citan en el trabajo, según requisitos exigidos por la circulación en líneas de alta velocidad (350 km/h., actualmente en construcción en España, pero que resultan generalizables a otro tipo de líneas menos exigentes y a ferrocarriles mineros.

Estudio de la susceptibilidad de un acero inoxidable austenítico estabilizado con niobio al dañado por tensocorrosión en medio H₂S (SSC y corrosión intergranular (IGC en otros medios agresivos

Directory of Open Access Journals (Sweden)

Gutiérrez de Saiz-Solabarría, S.

1998-05-01

Full Text Available Behavior to hydrogen damage caused by stress corrosion in a H₂S medium (SSC and to intergranular corrosion (IGC in different mediums, such as oxalic acid (C2H₂O₄-2H₂0, iron sulphate-50 % sulfuric acid [Fe₂(SO₄₃-50 % H₂SO₄], nitric acid (HNO₃, copper sulphate-16 % sulfuric acid (CuSO₄-5H₂O-16 % H₂SO₄ and cooper sulphate-50 % sulfuric acid (CuSO₄-5H₂O-50 % H₂SO₄, is studied in an AISI 347 austenitic stainless steel stabilized with 0.61 mass % Nb and hot rolled to a seamless pipe with 273.1 mm in diameter and 18.2 mm in thickness.

Se estudia el comportamiento de un acero inoxidable austenítico del tipo AISI 347 estabilizado con un 0,61 % en masa de Nb, laminado en caliente para producir una tubería sin soldadura de 273,1 mm de diámetro y 18,2 mm de espesor, frente al dañado por hidrógeno generado por tensocorrosión en medio H₂S (SSC y frente a la corrosión intergranular (IGC en diferentes medios agresivos tales como ácido oxálico (C₂H₂O₄∙2H₂O, sulfato de hierro-50% ácido sulfúrico [Fe₂ (SO₄₃-50 % H₂SO₄], ácido nítrico (HNO₃, sulfato de cobre-16% ácido sulfúrico (CuSO₄-5H₂O-16 % H₂SO₄ y sulfato de cobre-50 % ácido sulfúrico (CuSO₄-5H₂O-50 % H₂SO₄, respectivamente.

Corrosion and microstructural aspects of dissimilar joints of titanium and type 304L stainless steel

International Nuclear Information System (INIS)

Mudali, U. Kamachi.; Ananda Rao, B.M.; Shanmugam, K.; Natarajan, R.; Raj, Baldev

2003-01-01

To link titanium and zirconium metal based (Ti, Zr-2, Ti-5%Ta, Ti-5%Ta-1.8Nb) dissolver vessels containing highly radioactive and concentrated corrosive nitric acid solution to other nuclear fuel reprocessing plant components made of AISI type 304L stainless steel (SS), high integrity and corrosion resistant dissimilar joints between them are necessary. Fusion welding processes produce secondary precipitates which dissolve in nitric acid, and hence solid-state processes are proposed. In this work, various dissimilar joining processes available for producing titanium-304L SS joints with adequate strength, ductility and corrosion resistance for this critical application are highlighted. Developmental efforts made at IGCAR, Kalpakkam are outlined. The possible methods and the microstructural-metallurgical properties of the joints along with corrosion results obtained with three phase (liquid, vapour, condensate) corrosion testing are discussed. Based on the results, dissimilar joint produced by the explosive joining process was adopted for plant application

Acoustic emission during tensile deformation and fracture of nuclear grade AISI type 304 stainless steel specimens with notches

International Nuclear Information System (INIS)

Mukhopadhyay, C.K.; Jayakumar, T.; Baldev Raj

1996-01-01

Acoustic emission generated during tensile deformation and fracture of nuclear grade AISI type 304 stainless steel specimens with notches has been studied. The extent of acoustic activity generated depends on notch tip severity, notch tip blunting and tearing of the notches. The equation N=AK m applied to the acoustic emission data of the notched specimens has shown good correlation. Acoustic emission technique can be used to estimate the size of an unknown notch. (author)

Modifications on the behaviour of AISI 304 stainless steel submitted to creep caused by intermediate treatment of annealing

International Nuclear Information System (INIS)

Barreto, L.F.P.; Monteiro, S.N.

1982-01-01

Type AISI 304 austenitic stainless steel samples which have been previously creep deformed at 750 0 C, were annealed at 1100 0 C. The effects of this heat treatment in the mechanical behavior of this material when retested in creep were investigated. The results were analysed by taking into account the structural modifications observed and the controlling mechanisms which operate during the deformation and fracture occurring in the creep process. (Author) [pt

Carburizing plasma in a low temperature austenitic stainless steel AISI 304

International Nuclear Information System (INIS)

Mota, W.T.; Ramos, F.D.; Rocha, R.C.; Barcelos, M.V.; Barcelos, M.A.

2014-01-01

The industrial use of thermochemical treatment assisted by the cold plasma has been widely employed in recent years, mainly oriented to the excellent results obtained in the surface modification of engineering materials, when compared to more traditional methods. In this work, we studied the plasma carburizing low temperature steel AISI 304 mechanical parts used in construction. The thermochemical treatment was performed at a fixed gas atmosphere 7% CH 4 (g) and 93 % H 2 (g), 350 ° C and times of 1, 3 and 5 hours. Samples being tested for Vickers hardness, abrasive microwear, microstructure evaluation by optical microscopy and SEM and X-ray diffraction. The results show significant improvement in surface hardness, wear resistance and good formation of expanded austenite layer and no identifiers peaks of carbides. The results achieved are due to diffusion/adsorption of carbon present in the gaseous atmosphere to the evaluated samples. (author)

Formation of abrasion-resistant coatings of the AlSiFe{sub x}Mny intermetallic compound type on the AISI 304L alloy

Energy Technology Data Exchange (ETDEWEB)

Martinez-Peralez, L. G.; Flores-Valdes, A.; Salinas-Rodriguez, A.; Ochoa-Palacios, R. M.; Toscano-giles, J. A.; Torres-Torres, J.

2016-05-01

The α-Al{sub 9}FeMnSi and α-Al{sub 9}FeMn{sub 2}Si intermetallics formed by reactive sintering of Al, Si, Mn, Fe, Cr and Ni powders have been used in AISI 304L steels to enhance microhardness. Processing variables of the reactive sintering treatment were temperature (600, 650, 700, 750 and 800 degree centigrade), pressure (5, 10 y 20 MPa) and holding time (3600, 5400 y 7200 seconds). Experimental results show that temperature is the most important variable affecting the substrate/coating formation, while pressure does not appear to have a significant effect. The results show the optimum conditions of the reactive sintering that favor the substrate/coating formation are 800 degree centigrade, 20 MPa and 7200 seconds. Under these conditions, the reaction zone between the substrate and coating is more compacted and well-adhered, with a microhardness of 1300 Vickers. The results of SEM and X-Ray diffraction confirmed the formation of β-Al{sub 9}FeMnSi and β-Al{sub 9}FeMn{sub 2}Si intermetallics in the substrate/coating interface as well as the presence of Cr and Ni, indicating diffusion of these two elements from the substrate to the interface. (Author)

Investigation of residual stress in laser welding between carbon steel AISI 1010 and stainless AISI 304

International Nuclear Information System (INIS)

Mirim, Denilson de Camargo

2011-01-01

The dissimilar materials union has the residual stress formation as one of the most critical problems, which occurs mainly because these materials have both different thermal expansion coefficients and thermal conductivities. In this study, it was investigated the laser welding technique between steels, AISI 1010 and AISI 304. The materials were joined by butt autogenous welding with a continuous Nd:YAG laser. The main objective was to identify the welding parameters influence by the residual stresses analysis in the heat affected zone (HAZ). It was executed a factorial design with three-factor at two levels with a replica, which were varied power, welding speed and focal position of the laser beam. Residual stress measurements by the diffraction of X-rays were performed on the sample surface, to study their variation as a function of the parameters investigated. The blind hole method was also used to evaluate the residual stress along the samples depth, up to depth of 1mm. Besides residual stress measurement, weld seams were evaluated by optical and scanned electron microscopy, which were aimed to determine the weld geometry and changes in the microstructure. It was also made Vickers hardness measurements to evaluate the extent of HAZ. To evaluate the mechanical properties of the union were performed tensile and fatigue test. The MINITAB 15 software was used to analyze the residual stresses obtained by the blind hole method at different depths of the HAZ. It was also used statistical regression based on both the influences different and the combination of this input factors, in the residual stress of union. The results indicate that the models can satisfactorily predict the responses and provide users a guide to better define the welding parameters. (author)

Evaluación del coeficiente de endurecimiento del acero AISI 1045 deformado por rodillo

Directory of Open Access Journals (Sweden)

D. Alcántara

2011-12-01

Full Text Available El objetivo del trabajo es determinar el comportamiento del coeficiente de endurecimiento n por la ecuación de Hollomon en muestras cilíndricas de acero AISI 1045, las cuales, después de ser deformadas, se sometieron a ensayos de tracción. Se utiliza un diseño de experimento donde se tienen en cuenta las variables número de revolución (n con 27, 54 y 110 rev/min, fuerza de compresión (P de 500, 1 500 y   2 500 N y avance (S de 0,075; 0,125 y 0,25 mm/rev. Finalmente, aplicando el método de regresión se obtuvo un coeficiente de endurecimiento, el cual se aproxima a la linealidad cuando restringimos el cálculo a rangos de deformación elevados. Este coeficiente de endurecimiento se aplica en la ecuación de Hollomon para determinar el nuevo valor de tensión de fluencia y aplicarlo para el cálculo del trabajo mínimo a realizar en un proceso de deformación en frío empleando rodillo simple.   Palabras clave: Deformación Plástica; tensión; deformación; endurecimiento.The objective of the work is to determine the behavior of the hardening coefficient n by the equation of Hollomon, in cylindrical samples of steel AISI 1045, those which, after the deformed, were subjected to traction rehearsals. He used an experiment design where are kept in mind the revolution number (n with 27, 54 and 110 rev/min, it compression forces (P of 500, 1 500 and 2 500 N and feed (S of 0.075; 0.125 and 0.25 mm/rev. Finally, applying the regression method a hardening coefficient was obtained, which approaches to the linearity when restrict the calculation to high ranges of deformation. This hardening coefficient is applied in the equation of Hollomon for determine the new value of flow tension and to apply in the calculation of the minimum work to carry out in a cold process of deformation using simple roller.   Keywords: Plastic deformation; stress; deformation; hardening.

Sliding properties of coevaporated and nitrogen-implanted Pt50Ti50 films on AISI 304 stainless steel

International Nuclear Information System (INIS)

Zheng, L.R.; Hung, L.S.; Mayer, J.W.

1988-01-01

Thin Pt 50 Ti 50 films were deposited on a AISI 304 stainless steel substrate by co-evaporation. Dry sliding tests and wear track measurements revealed some improvement in sliding properties compared with the bare substrate. Implantation of the coated substrate with xenon ions did not produce any further improvement in friction and wear but a dramatic improvement resulted from nitrogen ion implantation. This was accompanied by a change in microstructure arising from an amorphous to crystalline phase transformation in the alloy film. (U.K.)

Influence of sintering atmosphere on the mechanical properties of steel P / M AISI 430L; Influencia de la atmosfera de sinterizacion en las propiedades mecanicas de los aceros P/M AISI 430L

Energy Technology Data Exchange (ETDEWEB)

Iglesias, F. J.; Martinez, C.; Costes, M. T.; Ruiz, J. M.; Garcia, L. E.; Corpas, F.

2014-04-01

It has studied the stainless steel powder metallurgy AISI 430L. It has compared the sintering in two different atmospheres; in vacuum, and in an atmosphere containing nitrogen. It has developed a heat treatment with the aim of improving the mechanical properties. This has been done through microstructural modification of complex nitrides of iron and chromium precipitates during the phase of sintering. Physical properties have been evaluated and are been performing a microstructural analysis for microstructure related to the increase in mechanical properties. (Author)

Investigating early stages of biocorrosion with XPS: AISI 304 stainless steel exposed to Burkholderia species

Science.gov (United States)

Johansson, Leena-Sisko; Saastamoinen, Tuomas

1999-04-01

We have investigated the interactions of an exopolymer-producing bacteria, Burkholderia sp. with polished AISI 304 stainless steel substrates using X-ray photoelectron spectroscopy (XPS). Steel coupons were exposed to the pure bacteria culture in a specially designed flowcell for 6 h during which the experiment was monitored in situ with an optical microscope. XPS results verified the formation of biofilm containing extracellular polymer on all the samples exposed to bacteria. Sputter results indicated that some ions needed for metabolic processes were trapped within the biofilm. Changes in the relative Fe concentration and Fe 2p peak shape indicated that also iron had accumulated into the biofilm.

Aplicación del ensayo miniatura de embutido para la evaluación de la tenacidad a temperaturas criogénicas de aceros inoxidables austeníticos envejecidos isotérmicamente

Directory of Open Access Journals (Sweden)

Saucedo-Muñoz, M. L.

2003-10-01

Full Text Available Two types of austenitic stainless steels JJl and JNl were isothermally aged at temperatures from 873 to 1173 K for 10 to 1000 min in order to study the microstructural evolution and its effect on fracture toughness at cryogenic temperatures. The Charpy V-Notch (CVN and Small-Punch (SPTesting methods were conducted at 77 K to evaluate the toughness of both solution treated and aged specimens. The fracture energy at 77 K determined for both methods showed a significant decrease with aging time for both steels. A linear correlation between the fracture energies of both methods was found. The intergranular precipitation of carbides and nitrides was responsible for the fracture toughness deterioration. The scanning electron microscope fractographs showed an intergranular brittle fracture and its fraction also increased with aging time and temperature. The presence of a more abundant intergranular precipitation resulted in a more rapid decrease in fracture toughness with aging time in JNl steel due to its higher content of C and N, compared to that of JJl steel.

Dos tipos de aceros inoxidables austeníticos, JJl y JNl, se envejecieron isotérmicamente a temperaturas entre 873 y 1.173 K por tiempos de 10 a 1.000 min, para estudiar la evolución microestructural y su efecto sobre la tenacidad a la fractura a temperaturas criogénicas. Los métodos de ensayo de impacto Charpy y el ensayo miniatura de embutido se llevaron a cabo a 77 K para evaluar la tenacidad de las muestras tratadas térmicamente. La energía de fractura determinada por ambos métodos mostró una disminución con el tiempo de envejecido para ambos aceros. Se encontró una relación lineal entre ambos valores de energía. La precipitación intergranular de carburos y nitruros fue la responsable de la pérdida de la tenacidad en las muestras envejecidas. La fractografía indicó que la fractura intergranular se incrementa con la temperatura y el tiempo de envejecido. La presencia

Caracterización y propiedades mecánicas a alta temperatura de un acero inoxidable dúplex

Directory of Open Access Journals (Sweden)

Jiménez, J. A.

1998-05-01

Full Text Available The microstructure and mechanical behavior at high temperature of a thermomechanical processed duplex stainless steel have been studied. Recrystalization of the material takes place during heating to test temperature, and a microstructure consisting of islands of austenitic grains of about 10-15 μm in size included in a more or less continuous matrix of ferrite is observed. Tensile tests at temperatures above 1,000°C and at low strain rates show a stress exponent of about 2 and elongations to failure up to 290 %. These values suggest that deformation is controlled by a grain boundary sliding mechanism, which causes a decrease in the size of the islands during deformation. Finally, an activation energy for plastic deformation of 167 kJ/mol was observed that was related to the activation energy for grain boundary diffusion of iron.

Se ha estudiado la microestructura y el comportamiento mecánico a alta temperatura de un acero inoxidable dúplex procesado termomecánicamente. Durante el calentamiento a la temperatura de ensayo, el material recristaliza y se obtiene una microestructura de granos austeníticos de tamaños comprendidos entre 10 y 15 μm agrupados en islas incluidas en una matriz más o menos continua de ferrita. Ensayos de tracción a temperaturas superiores a 1.000°C y bajas velocidades de deformación muestran un exponente de la tensión igual a 2 y alargamientos a rotura de hasta 290 %. Estos valores permiten asociar el mecanismo de deformación al deslizamiento de fronteras de grano, el cual determina la desaparición progresiva de las islas de granos austeníticos durante la deformación. Finalmente, se encontró un valor de 167 kJ/mol para la energía de activación de la deformación plástica, la cual se relacionó con la energía de autodifusión del hierro a lo largo de las fronteras de grano.

Soldadura TIG de los aceros inoxidables dúplex del tipo 22-05 (Uranus 45N y Avesta. Estudio de la microestructura y de las propiedades mecánicas

Directory of Open Access Journals (Sweden)

Gómez de Salazar, J. M.

1998-05-01

Full Text Available TIG welding of two different duplex stainless steels is carried out. Arc-discharge on base-material plates by means of the TIG technique without filler metal and varying the energetic conditions (E.N.A. has been performed, A comparative study concerning the microstructural evolution as well as mechanical properties is carried out, The relation between hardness profiles, the microstructural variations and the ferrita δ concentration is established. Further, the above mentioned properties are related to the E.N.A. for each welded joint.

Se estudia la soldadura TIG de dos aceros inoxidables dúplex. Para ello, se ha descargado un arco sobre las chapas de material base mediante la técnica TIG, sin aportación de material y variando las E.N.A. Se realiza un estudio comparativo de la evolución microestructural, así como de las propiedades mecánicas. Se establece la relación entre los perfiles de dureza obtenidos y la variación microestructural y de la concentración de ferrita δ, así como estas propiedades con el E.N.A, de cada cordón.

Separación selectiva de hierro y cromo de las lejías agotadas del decapado de acero inoxidable

Directory of Open Access Journals (Sweden)

Gálvez, J. L.

2005-12-01

Full Text Available Stainless steel spent pickling baths are very complex solutions of metals and acids (HNO₃ and HF and are a very important environmental concern. Several processes have been developed for acid recovery (free and bounded acid with techniques like acid retardation, solvent extraction, evaporation and dialysis diffusion. In these processes, metallic content is precipitated and treated for its disposal. We have developed a process that permits the separation of metals by means of a selective precipitation, induced by adding free fluoride. Iron (Fe and chromium (Cr precipitate as pentafluorides and nitrogennickel (Ni remains in solution. After this stage, complex fluorides can be hydrolized with alkali to give iron and chromium hydroxides, releasing fluoride in solution

Los baños ácidos agotados del decapado de acero inoxidable son disoluciones muy complejas debido al alto contenido de metales y ácidos (HNO₃ y HF, por lo que constituyen un grave problema medioambiental. Existen tratamientos comerciales para la recuperación del ácido (libre o complejado que se basan en técnicas de retardo ácido, extracción con disolventes, evaporación o membranas. En estos procesos el contenido metálico es precipitado y tratado como un residuo. El grupo de investigación formado por los autores del presente trabajo ha desarrollado un procedimiento que permite el aprovechamiento de dichos metales mediante su recuperación selectiva con una técnica de precipitación modificada inducida por fluoruro libre. Se consigue la precipitación de hierro (Fe y cromo (Cr como pentafluoruros (pH 3-4,5 dejando el níquel en disolución. Posteriormente, los fluoruros complejos son hidrolizados con álcali dando lugar a hidróxidos de hierro y cromo, mientras que el fluoruro es redisuelto.

Relaciones cuantitativas entre los contenidos de azufre y de sulfuros en los aceros inoxidables tipo AISI 303: influencia de la composición química de los sulfuros

OpenAIRE

Botella, J.; Merino, C.; Heredia, M. A.; Almagro, J.

1999-01-01

The work has been done with ten AISI 303 stainless steel rods which have similar chemical compositions, except for sulphur which varies between 0.25 and 0.36%. These steels are studied by Scanning Electron Microscopy (SEM) and Energy Dispersive X-Ray Spectrometry (EDX). The sulphides are chemically microanalysed and the occupied volume determined by automatic image analysis. It can be inferred that the chemical composition of sulphides in AISI 303 steels is variable to some extent even though...

Evaluación electroquímica de soldaduras en tubos capilares de acero inoxidable

Directory of Open Access Journals (Sweden)

Javier E. Rodríguez-Yáñez

2014-02-01

Full Text Available La recuperación de capilares de acero 316L utilizados en pozos geotérmicos neutros, por medio de soldadura orbital autógena, se evalúa desde el punto de vista de su resistencia a la corrosión en las condiciones de utilización, mediante técnicas electroquímicas básicas. En el pretratamiento se encuentra que es más conveniente realizar un decapado químico previo a la soldadura por 5 minutos. Mientras que posteriormente a la soldadura, la aplicación de tratamiento térmico de reducción de tensiones no se justifica desde el punto de vista de la resistencia a la corrosión. También se plantea la comparación de los capilares soldados respecto a capilares nuevos y usados, teniendo los capilares soldados un comportamiento intermedio entre ambos.

The effect of inhibitor sodium nitrate on pitting corrosion of dissimilar material weldment joint of stainless steel AISI 304 and mild steel SS 400

Energy Technology Data Exchange (ETDEWEB)

Hilca, B. R., E-mail: bangkithilca@yahoo.com; Triyono, E-mail: triyonomesin@uns.ac.id [Mechanical Engineering Department, Sebelas Maret University, Surakarta 57126 (Indonesia)

2016-03-29

This study experimentally evaluated the effect of Sodium Nitrate inhibitor (NaNO{sub 3}) of 0.1%, 0.3%, and 0.5% on NaCl 3.5% toward pitting corrosion of dissimilar metal welding joint between stainless steel AISI 304 and mild steel SS 400. Electrochemical corrosion was tested using potentiodynamic polarization. Further the Scanning Electron Microscope (SEM) conducted to analyze the specimen. Chemical composition analysis used Energy Dispersive X-ray Spectrometry (EDS). The highest efficiency of sodium nitrate for ER 308 attained 63.8% and 64.89%for ER 309L. The specimen surface which observed through SEM showed decrease of pitting corrosion respectively with the addition of sodium nitrate content as inhibitor.

Chemical sanitizers to control biofilms formed by two Pseudomonas species on stainless steel surface Sanificantes químicos no controle de biofilmes formados por duas espécies de Pseudomonas em superfície de aço inoxidável

Directory of Open Access Journals (Sweden)

Danila Soares Caixeta

2012-03-01

Full Text Available The biofilm formation of Pseudomonas aeruginosa and Pseudomonas fluorescens on AISI 304 stainless steel in the presence of reconstituted skim milk under different temperatures was conducted, and the potential of three chemical sanitizers in removing the mono-species biofilms formed was compared. Pseudomonas aeruginosa cultivated in skim milk at 28 °C presented better growth rate (10.4 log CFU.mL-1 when compared with 3.7 and 4.2 log CFU.mL-1 for P. aeruginosa and P. fluorescens cultivated at 7 °C, respectively. Pseudomonas aeruginosa formed biofilm when cultivated at 28 °C. However, only the adhesion of P. aeruginosa and P. fluorescens was observed when incubated at 7 °C. The sodium dichloroisocyanurate was the most efficient sanitizer in the reduction of the adhered P. aeruginosa cells at 7 and 28 °C and those on the biofilm, respectively. The hydrogen peroxide was more effective in the reduction of adhered cells of P. fluorescens at 7 °C.A capacidade de adesão e formação de biofilme por Pseudomonas aeruginosa e Pseudomonas fluorescens em aço inoxidável AISI 304, na presença de leite desnatado resconstituído sobre diferentes temperaturas foi conduzido e o potencial de três sanificantes químicos na remoção de biofilmes monoespécies foi comparado. Pseudomonas aeruginosa cultivada em leite desnatado a 28 °C apresentou melhor crescimento (10,4 log UFC.mL-1 quando comparado com 3,7 and 4,2 log UFC.mL-1 para P. aeruginosa e P. fluorescens cultivadas a 7 °C, respectivamente. Pseudomonas aeruginosa formou biofilme quando cultivada a 28 °C. Contudo foi observado somente adesão de P. aeruginosa e P. fluorescens quando incubada a 7 °C. O dicloroisocianurato de sódio foi o sanificante mais eficiente na redução de células aderidas e em biofilme de P. aeruginosa a 7 e 28 °C, respectivamente. O peróxido de hidrogênio foi o mais eficiente na redução de células aderidas de P. fluorescens a 7 °C.

Applications of the essay at slow deformation velocity in pipes of stainless steel AISI-304

International Nuclear Information System (INIS)

Zamora R, L.; Mora R, T. De la

2004-01-01

Nowadays is carried out research related with the degradation mechanisms of structures, systems and/or components in the nuclear power plants, since many of the involved processes are those responsible for the dependability of these, of the integrity of the components and of the aspects of safety. The purpose of this work, was to determine the grade of susceptibility to the corrosion of a pipe of Austenitic stainless steel AISI 304, in a solution of Na CI (3.5%) to the temperatures of 60 and 90 C, in two different thermal treatments - 1. - Sensitive 650 C by 4 hours and cooled in water. 2. Solubilized to 1050 C by 1 hour and cooled in water

Fatigue assessment by energy approach during tensile tests on AISI 304 steel

Directory of Open Access Journals (Sweden)

A. Risitano

2017-01-01

Full Text Available Estimation of the fatigue limit for steel ductile materials using non-destructive methods is a topic of great interest to researchers today. In recent years, the method adopted has implemented infrared sensors to detect the surface temperature and correlate it with the fatigue limit. In previous paper, a new energy approach was proposed to investigate the fatigue limit during tensile test. The numerical procedure proposed by Chrysochoos is adopted to clean infrared images and applied to analyse the surface heat sources during tensile test. AISI 304 specimens with rectangular cross-sections are tested. Moreover fatigue tests at increasing loads were carried out on steel by a stepwise succession, applied to the same specimen, for applying the thermographic method. The predictions of the fatigue limit, obtained by the analysis of the energy evolution during the static tests, were compared with the predictions obtained applying the thermographic method during fatigue tests.

Improvement of pitting corrosion resistance of AISI 304L stainless steel by nano-pulsed laser surface melting

International Nuclear Information System (INIS)

Pacquentin, W.; Blanc, C.; Caron, N.; Thro, P.Y.; Cheniere, A.; Tabarant, M.; Moutiers, G.; Miserque, F.; Plouzennec, H.; Oltra, R.

2013-01-01

The stainless steel 304L is widely used, however, in particular conditions, it may be sensitive to pitting corrosion. Nano-pulsed laser surface melting is a surface treatment which allows improving the corrosion resistance of this steel. This treatment consists in focusing a laser beam on the surface of the material, involving its quite immediately melting through a few microns depth, then an ultra-fast solidification occurs with cooling rate about 1011 K/s. The laser parameters control the modifications of the physico-chemical properties. In particular, we studied the influence of the impacts overlap of an ytterbium laser-fiber on the corrosion resistance of a 304L stainless steel in conditions of an aerated and agitated solution of NaCl (concentration of 30 g/L). We obtained an increase of the pitting potential of 220 mV, highlighting an improvement of the corrosion resistance. The study of the chemical and structural modifications is not enough to explain the improvement of the corrosion resistance. Other phenomena must be taken into account, as the quality of the oxide layer, in terms of physico-chemical and mechanical properties. (authors)

Effects of Loading Frequency on Fatigue Behavior, Residual Stress, and Microstructure of Deep-Rolled Stainless Steel AISI 304 at Elevated Temperatures

Science.gov (United States)

Nikitin, I.; Juijerm, P.

2018-02-01

The effects of loading frequency on the fatigue behavior of non-deep-rolled (NDR) and deep-rolled (DR) austenitic stainless steel AISI 304 were systematically clarified at elevated temperatures, especially at temperatures exhibiting the dynamic strain aging (DSA) phenomena. Tension-compression fatigue tests were performed isothermally at temperatures of 573 K and 773 K (300 °C and 500 °C) with different loading frequencies of 5, 0.5, 0.05, and 0.005 Hz. For the DR condition, the residual stresses and work-hardening states will be presented. It was found that DSA would be detected at appropriate temperatures and deformation rates. The cyclic deformation curves and the fatigue lives of the investigated austenitic stainless steel AISI 304 are considerably affected by the DSA, especially on the DR condition having high dislocation densities at the surface and in near-surface regions. In the temperature range of the DSA, residual stresses and work-hardening states of the DR condition seem to be stabilized. The microstructural alterations were investigated by transmission electron microscopy (TEM). At an appropriate temperature with low loading frequency, the plastic deformation mechanism shifted from a wavy slip manner to a planar slip manner in the DSA regimes, whereas the dislocation movements were obstructed.

Una herramienta para la selección automatizada de aceros en el contexto // A tool for the automated selection of steels in the Mechanical Engineering´s context

Directory of Open Access Journals (Sweden)

L. Dumitrescu

2010-01-01

Full Text Available ResumenEl diseno de Ingenieria de un producto o componente constituye una actividad dificil, compleja ymultidisciplinaria, enfocada a la resolucion de problemas. En el presente trabajo se muestra eldesarrollo de una herramienta automatizada para la seleccion de los aceros mas utilizados en laconstruccion de maquinarias. La herramienta constituye una ayuda para la seleccion de losmateriales desde la etapa conceptual del proceso de diseno, donde se identifican las diferentescategorias de materiales a utilizar. La herramienta comprende las caracteristicas y propiedades masrelevantes de los aceros de Ingenieria disponibles en seis normas internacionales: Japonesa (JIS,Alemana (DIN, Vbn, DIN-Vbn, Rusa (GOST, Americana (AISI, SAE, AISI-SAE, ASTM, Inglesa (BS, EN,GB, Francesa (AFNOR y la Norma Cubana (NC vigente.Palabras claves: materiales, automatizada, aceros, ingenieria.____________________________________________________________AbstractThe product or component design constitutes a difficult, complex and multidisciplinary activity,focused to the resolution of problems. Presently work show the development of an automated toolfor the selection of the more used steels in the construction of machineries. The tool constitute ahelp for the selection of the materials from the conceptual stage of the design process, where thedifferent categories of materials are identified to use. The tool analyze the characteristics and morecommon properties of the available steels in six international standards: JIS (Japan, DIN, Vbn, DINVbn(Germany, GOST (Russia, AISI, SAE, AISI-SAE, ASTM (USA, BS, IN, GB (England, AFNOR(France and NC (Cuba.Key words: materials, automated, steels, engineering.

Comparación entre los diagramas TTS obtenidos mediante los ensayos normalizados Huey y Strauss modificado para el acero inoxidable AISI 304

Directory of Open Access Journals (Sweden)

Otero, E.

1996-04-01

Full Text Available This work presents a comparison of Temperature-Time-Sensitization TTS diagrams obtained by Huey and modified Strauss standard, for detecting susceptibility to intergranular attack. The difference between these tests is the use of a strong or a slightly smooth oxidizing electrolyte. The diagrams obtained are different and if a sample tested by modified Strauss is sensitized, then it will be sensitized in the Huey test, but the contrary is not always true. This difference is because a sensitized sample has to have a continuous band lacking in chromium along the grain boundary in order to be sensitized in the modified Strauss test. This condition is not necessary in the Huey test.

Se comparan los diagramas Temperatura-Tiempo-Sensibilización TTS, obtenidos mediante los ensayos normalizados de corrosión intergranular Huey y Strauss modificado, que, respectivamente, utilizan electrólitos fuerte y suavemente oxidantes, mostrándose que los diagramas obtenidos son diferentes. Si una muestra evaluada mediante el ensayo Strauss modificado se encuentra sensibilizada, entonces lo estará también en el ensayo Huey, pero no necesariamente ocurrirá lo contrario; esta diferencia se asocia a la necesidad de la existencia de una zona continua empobrecida en cromo a lo largo del límite de grano para que el material se sensibilice con respecto al ensayo Strauss modificado, condición innecesaria para el caso del ensayo Huey.

Junções de materiais dissimilares utilizando o processo de soldagem por fricção rotativa

OpenAIRE

Eder Paduan Alves

2010-01-01

O objetivo desse trabalho é o desenvolvimento de junções no estado sólido de materiais dissimilares alumínio AA 1050 e aço inoxidável AISI 304, que possam ser utilizadas nas tubulações de reservatórios de propelentes líquidos e demais tubulações dos Veículos Lançadores de Satélites. As junções foram obtidas pelo processo de soldagem por fricção rotativa convencional, que combina o calor gerado entre o atrito de duas superfícies e deformação mecânica. Foram realizados testes de soldagem com di...

Electrochemical behaviour of iron and AISI 304 stainless steel in simulated acid rain solution

Energy Technology Data Exchange (ETDEWEB)

Pilic, Zora; Martinovic, Ivana [Mostar Univ. (Bosnia and Herzegovina). Dept. of Chemistry

2016-10-15

The growth mechanism and properties of the oxide films on iron and AISI 304 stainless steel were studied in simulated acid rain (pH 4.5) by means of electrochemical techniques and atomic absorption spectrometry. The layer-pore resistance model was applied to explain a potentiodynamic formation of surface oxides. It was found that the growth of the oxide film on iron takes place by the low-field migration mechanism, while that on the stainless steel takes place by the high-field mechanism. Kinetic parameters were determined. Impedance measurements revealed that Fe surface film has no protective properties at the open circuit potential, while the resistance of stainless steel oxide film is very high. The concentration of the metallic ions released into solution and measured by atomic absorption spectroscopy was in accordance with the results obtained from the electrochemical techniques.

CrN coatings deposited by magnetron sputtering: Mechanical and tribological properties

Directory of Open Access Journals (Sweden)

Alexander Ruden-Muñoz

2015-01-01

Full Text Available Se analizaron las propiedades mecánicas y tribológicas de recubrimientos de CrN crecidos sobre sutratos de aceros AISI 203 y AISI 4140 usando la técnica de pulverización catódica con magnetrón. Los recubrimietos fueron crecidos a dos presiones de trabajo, 0.4 y 4.0 Pa. Las películas crecidas sobre acero AISI 304 a 0.4 Pa mostraron la dureza más alta debido a que ésta presenta gran tamaño de grano y baja rugosidad. Para los recubrimientos sinterizados a o.4 Pa, el daño superficial fue bajo durante la prueba tribológica. Se realizaron estudios de adherencia, obteniéndose Lc1 y Lc2 para los recubrimietos producidos con ambas presiones y en abos sustratos. Se observó una mejor adherencia en las películas crecidas a baja presión debido a su mayor espesor (~890 nm.

Tensiones de contacto por el método de elementos finitos del acero AISI 1045 endurecido por rodillo

Directory of Open Access Journals (Sweden)

Fernández-Columbié, T.

2012-02-01

Full Text Available In this paper, the tense-deformational behavior is analyzed by means of simulation using the finite element method for AISI 1045 cold rolled deformed steel. ANYSYS V.10 software was used in this study. Revolution number, compressive strength and tool feed rate were the variables considered in the deformation process. They allowed determining the contact stress of the deformed material. The material used was 30 mm diameter and 100 mm length. Samples of 30 mm diameter and 3 mm thickness were prepared for the optical microscopic observation, which were compared to the results obtained from the simulation. The tensile status of the deformed samples was evaluated as from the reduction of the average size of the grains as per the strength applied. This study intends to show that the cold hardening method is a surface hardening option.

En el trabajo se analiza el estado tenso-deformacional mediante la simulación por el método de los elemento finitos del acero AISI 1045 deformado en frío empleando rodillo simple, para ello se utilizó el software ANSYS V.10. En el proceso de deformación se consideran las variables número de revolución, la fuerza compresiva y el avance de la herramienta, lo que permitió determinar las tensiones de contacto del material deformado. El diámetro del material empleado fue de 30 mm con una longitud de 100 mm. Para la observación de la microscopía óptica, se prepararon muestras de 30 mm de diámetro por 3 mm de espesor, las que fueron comparadas con los resultados obtenidos de la simulación. El estado tensional de las muestras deformadas se evaluó a partir de la reducción del tamaño promedio de los granos según la fuerza empleada. Con el desarrollo del trabajo se trata de demostrar que el empleo del método de endurecimiento en frío es una alternativa de endurecimiento superficial.

Q-switch Nd:YAG laser welding of AISI 304 stainless steel foils

Energy Technology Data Exchange (ETDEWEB)

P' ng, Danny [Laboratory for Lasers, MEMS and Nanotechnology, Department of Mechanical Engineering, Iowa State University, Ames, IA 50011-2161 (United States); Molian, Pal [Laboratory for Lasers, MEMS and Nanotechnology, Department of Mechanical Engineering, Iowa State University, Ames, IA 50011-2161 (United States)], E-mail: molian@iastate.edu

2008-07-15

Conventional fusion welding of stainless steel foils (<100 {mu}m thickness) used in computer disk, precision machinery and medical device applications suffer from excessive distortion, formation of discontinuities (pore, void and hot crack), uncontrolled melting (melt-drop through) and poor aesthetics. In this work, a 15 ns pulsed, 400 mJ Nd:YAG laser beam was utilized to overcome these barriers in seam welding of 60 {mu}m thin foil of AISI 304 stainless steel. Transmission electron microscopy was used to characterize the microstructures while hardness and tensile-shear tests were used to evaluate the strengths. Surface roughness was measured using a DekTak profilometer while porosity content was estimated using the light microscope. Results were compared against the data obtained from resistance seam welding. Laser welding, compared to resistance seam welding, required nearly three times less heat input and produced welds having 50% narrower seam, 15% less porosity, 25% stronger and improved surface aesthetics. In addition, there was no evidence of {delta}-ferrite in laser welds, supporting the absence of hot cracking unlike resistance welding.

Effect of Built-Up Edge Formation during Stable State of Wear in AISI 304 Stainless Steel on Machining Performance and Surface Integrity of the Machined Part.

Science.gov (United States)

Ahmed, Yassmin Seid; Fox-Rabinovich, German; Paiva, Jose Mario; Wagg, Terry; Veldhuis, Stephen Clarence

2017-10-25

During machining of stainless steels at low cutting -speeds, workpiece material tends to adhere to the cutting tool at the tool-chip interface, forming built-up edge (BUE). BUE has a great importance in machining processes; it can significantly modify the phenomenon in the cutting zone, directly affecting the workpiece surface integrity, cutting tool forces, and chip formation. The American Iron and Steel Institute (AISI) 304 stainless steel has a high tendency to form an unstable BUE, leading to deterioration of the surface quality. Therefore, it is necessary to understand the nature of the surface integrity induced during machining operations. Although many reports have been published on the effect of tool wear during machining of AISI 304 stainless steel on surface integrity, studies on the influence of the BUE phenomenon in the stable state of wear have not been investigated so far. The main goal of the present work is to investigate the close link between the BUE formation, surface integrity and cutting forces in the stable sate of wear for uncoated cutting tool during the cutting tests of AISI 304 stainless steel. The cutting parameters were chosen to induce BUE formation during machining. X-ray diffraction (XRD) method was used for measuring superficial residual stresses of the machined surface through the stable state of wear in the cutting and feed directions. In addition, surface roughness of the machined surface was investigated using the Alicona microscope and Scanning Electron Microscopy (SEM) was used to reveal the surface distortions created during the cutting process, combined with chip undersurface analyses. The investigated BUE formation during the stable state of wear showed that the BUE can cause a significant improvement in the surface integrity and cutting forces. Moreover, it can be used to compensate for tool wear through changing the tool geometry, leading to the protection of the cutting tool from wear.

Degradación de recubrimientos ZrO2-CaO/NiAlMo por oxidación isoterma

Directory of Open Access Journals (Sweden)

Utrilla, V.

2006-12-01

Full Text Available This paper analyses the degradation of a ceramic top coating 70%ZrO2 – 30%CaO deposited onto a stainless steel AISI 304 by thermal spray, using Ni-6%Al-5%Mo as overlay coating. These thermal barrier coatings were heat treated for 48, 120 and 288 h at 800 ºC to evaluate the degradation of these materials by isothermal oxidation. The microstructure evolution during oxidation was analysed by environmental scanning electron microscopy, transmission electron microscopy, X ray microanalysis and X ray diffraction. A thermally grown oxide layer was observed between the overlay coating and the ceramic top coating after oxidation. This layer was formed by a mixed Al and Ni oxides.En este trabajo se estudia la degradación de un recubrimiento 70%ZrO2 – 30%CaO crecido por proyección térmica de oxiacetileno sobre un acero inoxidable austenítico AISI 304 y empleando una leación de Ni-6%Al-5%Mo como capa de anclaje. Los recubrimientos se trataron térmicamente en aire a 800 ºC durante 48, 120 y 288 horas para evaluar la degradación de estos materiales por oxidación isotérmica. La evolución de la microestructura de las barreras como consecuencia del proceso de oxidación se analizó mediante microscopía electrónica de barrido ambiental, microscopía electrónica de transmisión, microanálisis de rayos X (EDX y difracción de rayos X. Durante la oxidación de los recubrimientos creció una capa intermedia de óxidos (“thermally grown oxides”, TGO entre el anclaje metálico y el recubrimiento cerámico formada por una mezcla de óxidos de Al y Ni.

pH effect on pit potential and protection potential of stainless steels AISI-304, 310 and 316 in NaCl solution

International Nuclear Information System (INIS)

Cabral, U.Q.; Sathler, L.; Mariano Neto, F.

1973-06-01

For three austenitic stainless steels, AISI 304, 310 and 316, the pH influence on the rupture, protection and corrosion potentials was studied in a 0,5N NACl solution. The pit potentials determined by the chronogalvonometric method, are pH independent within the acid range. They showed a rough linear variation within the basic range having a maximum corresponding to the pH value of 8.8. The electrochemical hysteresis method, employed for determining the protection potential, presented a total pH independence for the AISI 316. The other steels showed a small dependence within the basic range but with a tendency for the protection potential to become slightly more active with increasing pH, within the acid range. It was also noted for the three steels studied that the corrosion potental became more active with increasing pH, within the basic range [pt

Measurement of carbon activity in sodium by Fe-Mn 20% alloy, and by strainless austenitic steel 304L and 316L

International Nuclear Information System (INIS)

Oberlin, C.; Saint Paul, P.; Baque, P.; Champeix, L.

1980-01-01

Precise knowledge of carbon activity in sodium used as coolant in fast breeder reactors, is essential for continuous survey of carburization-decarburization processes. Carbon activity can be periodically surveyed by measuring the carbon concentration or by hot trap like metal alloy strip placed in sodium loop. In fact, in equilibrium, activity of carbon in sodium is equal to the activity in metal alloy. Thus if the relation between concentration of carbon and it activity in the alloy is known, it is possible to estimate the activity of carbon in sodium. Materials to be used should have high solubility in carbon at the needed temperature. They should quickly attain equilibrium with sodium and they should not contain impurities that can affect the results. Materials chosen according to these criteria were Fe-Mn 20%, stainless austenitic steel AISI 304L and 316L

Desgaste por deslizamiento en seco de aceros perlíticos y bainíticos

Directory of Open Access Journals (Sweden)

Cristian Camilo Viáfara Arango

2004-01-01

Full Text Available El desgaste por deslizamiento tiene una gran influencia sobre el desempeño de los sistemas rueda-riel, en particular, por el deslizamiento de la pestaña de la rueda sobre la parte interna del riel en una pista curva. Dado que el deslizamiento entre la rueda y el riel involucra efectos de adhesión, altos porcentajes de deslizamiento/rodadura afectan fuertemente el desgaste por fatiga de contacto por rodadura, que actúa en las superficies de contacto. En una máquina Pin sobre Disco se llevaron a cabo ensayos de desgaste por deslizamiento para estudiar el comportamiento del acero perlítico AISI 1070 y el bainítico AISI 15B30. La velocidad de deslizamiento fue 1 ms-1 para todas las pruebas y se utilizaron cargas normales de 10, 30 y 50 N. La resistencia al desgaste fue relacionada con la pérdida de masa medida después de las pruebas y las superficies desgastadas, al igual que las partículas removidas, fueron analizadas por medio de los microscopios óptico y electrónico. Se realizaron perfiles de microdureza bajo las superficies de contacto para analizar el efecto del endurecimiento por deformación. El acero perlítico mostró mayor resistencia al desgaste que el acero bainítico, debido al excelente comportamiento de endurecimiento por deformación de la perlita comparado con el de la bainita. En el acero perlítico se observaron regímenes de desgaste oxidativo, mientras que en el bainítico el principal mecanismo de remoción de material fue el adhesivo, llevando a un daño mucho más fuerte en la superficie. De hecho, el régimen de desgaste para las probetas bainíticas fue siempre severo, aún con la menor carga normal aplicada.

Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65

International Nuclear Information System (INIS)

Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L.

2004-01-01

In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

Evaluation of AISI 316L stainless steel welded plates in heavy petroleum environment

International Nuclear Information System (INIS)

Carvalho Silva, Cleiton; Pereira Farias, Jesualdo; Batista de Sant'Ana, Hosiberto

2009-01-01

This work presents the study done on the effect of welding heating cycle on AISI 316L austenitic stainless steel corrosion resistance in a medium containing Brazilian heavy petroleum. AISI 316L stainless steel plates were welded using three levels of welding heat input. Thermal treatments were carried out at two levels of temperatures (200 and 300 deg. C). The period of treatment in all the trials was 30 h. Scanning electronic microscopy (SEM) and analysis of X-rays dispersive energy (EDX) were used to characterize the samples. Weight loss was evaluated to determine the corrosion rate. The results show that welding heating cycle is sufficient to cause susceptibility to corrosion caused by heavy petroleum to the heat affected zone (HAZ) of the AISI 316L austenitic stainless steel

Influence of delta ferrite on corrosion susceptibility of AISI 304 austenitic stainless steel

Directory of Open Access Journals (Sweden)

Lawrence O. Osoba

2016-12-01

Full Text Available In the current study, the influence of delta (δ ferrite on the corrosion susceptibility of AISI 304 austenitic stainless steel was evaluated in 1Molar concentration of sulphuric acid (H2SO4 and 1Molar concentration of sodium chloride (NaCl. The study was performed at ambient temperature using electrochemical technique—Tafel plots to evaluate the corrosive tendencies of the austenitic stainless steel sample. The as-received (stainless steel specimen and 60% cold-worked (stainless steel specimens were isothermally annealed at 1,100°C for 2 h and 1 h, respectively, and quenched in water. The results obtained show that the heat-treated specimen and the 60% cold-worked plus heat-treated specimen exhibited higher corrosion susceptibility than the as-received specimen, which invariably contained the highest fraction of δ ferrite particles. The finding shows that the presence of δ ferrite, in which chromium (Cr, the main corrosion inhibitor segregates, does not degrade and or reduces the resistance to aqueous corrosion of the austenitic stainless steel material.

Evaluation of AISI Type 304 stainless steel as a suitable surface material for evaluating the efficacy of peracetic acid-based disinfectants against Clostridium difficile spores.

Directory of Open Access Journals (Sweden)

Elaine Black

Full Text Available Disinfectants play an important role in controlling microbial contamination on hard surfaces in hospitals. The effectiveness of disinfectants in real life can be predicted by laboratory tests that measure killing of microbes on carriers. The modified Quantitative Disk Carrier Test (QCT-2 is a standard laboratory method that employs American Iron and Steel Institute (AISI Type 430 stainless steel carriers to measure hospital disinfectant efficacy against Clostridium difficile spores. The formation of a rust-colored precipitate was observed on Type 430 carriers when testing a peracetic acid (PAA-based disinfectant with the QCT-2 method. It was hypothesized that the precipitate was indicative of corrosion of the Type 430 carrier, and that corrosion could impact efficacy results. The objective of this study was to compare the suitability of AISI Type 430 to Type 304 stainless steel carriers for evaluating PAA-based disinfectants using the QCT-2 method. Type 304 is more corrosion-resistant than Type 430, is ubiquitous in healthcare environments, and is used in other standard methods. Suitability of the carriers was evaluated by comparing their impacts on efficacy results and PAA degradation rates. In efficacy tests with 1376 ppm PAA, reductions of C. difficile spores after 5, 7 and 10 minutes on Type 430 carriers were at least about 1.5 log10 lower than reductions on Type 304 carriers. In conditions simulating a QCT-2 test, PAA concentration with Type 430 carriers was reduced by approximately 80% in 10 minutes, whereas PAA concentration in the presence of Type 304 carriers remained stable. Elemental analyses of residues on each carrier type after efficacy testing were indicative of corrosion on the Type 430 carrier. Use of Type 430 stainless steel carriers for measuring the efficacy of PAA-based disinfectants should be avoided as it can lead to an underestimation of real life sporicidal efficacy. Type 304 stainless steel carriers are recommended as a

Evaluation of AISI Type 304 stainless steel as a suitable surface material for evaluating the efficacy of peracetic acid-based disinfectants against Clostridium difficile spores.

Science.gov (United States)

Black, Elaine; Owens, Krista; Staub, Richard; Li, Junzhong; Mills, Kristen; Valenstein, Justin; Hilgren, John

2017-01-01

Disinfectants play an important role in controlling microbial contamination on hard surfaces in hospitals. The effectiveness of disinfectants in real life can be predicted by laboratory tests that measure killing of microbes on carriers. The modified Quantitative Disk Carrier Test (QCT-2) is a standard laboratory method that employs American Iron and Steel Institute (AISI) Type 430 stainless steel carriers to measure hospital disinfectant efficacy against Clostridium difficile spores. The formation of a rust-colored precipitate was observed on Type 430 carriers when testing a peracetic acid (PAA)-based disinfectant with the QCT-2 method. It was hypothesized that the precipitate was indicative of corrosion of the Type 430 carrier, and that corrosion could impact efficacy results. The objective of this study was to compare the suitability of AISI Type 430 to Type 304 stainless steel carriers for evaluating PAA-based disinfectants using the QCT-2 method. Type 304 is more corrosion-resistant than Type 430, is ubiquitous in healthcare environments, and is used in other standard methods. Suitability of the carriers was evaluated by comparing their impacts on efficacy results and PAA degradation rates. In efficacy tests with 1376 ppm PAA, reductions of C. difficile spores after 5, 7 and 10 minutes on Type 430 carriers were at least about 1.5 log10 lower than reductions on Type 304 carriers. In conditions simulating a QCT-2 test, PAA concentration with Type 430 carriers was reduced by approximately 80% in 10 minutes, whereas PAA concentration in the presence of Type 304 carriers remained stable. Elemental analyses of residues on each carrier type after efficacy testing were indicative of corrosion on the Type 430 carrier. Use of Type 430 stainless steel carriers for measuring the efficacy of PAA-based disinfectants should be avoided as it can lead to an underestimation of real life sporicidal efficacy. Type 304 stainless steel carriers are recommended as a suitable

Evaluation of AISI Type 304 stainless steel as a suitable surface material for evaluating the efficacy of peracetic acid-based disinfectants against Clostridium difficile spores

Science.gov (United States)

Owens, Krista; Staub, Richard; Li, Junzhong; Mills, Kristen; Valenstein, Justin; Hilgren, John

2017-01-01

Disinfectants play an important role in controlling microbial contamination on hard surfaces in hospitals. The effectiveness of disinfectants in real life can be predicted by laboratory tests that measure killing of microbes on carriers. The modified Quantitative Disk Carrier Test (QCT-2) is a standard laboratory method that employs American Iron and Steel Institute (AISI) Type 430 stainless steel carriers to measure hospital disinfectant efficacy against Clostridium difficile spores. The formation of a rust-colored precipitate was observed on Type 430 carriers when testing a peracetic acid (PAA)-based disinfectant with the QCT-2 method. It was hypothesized that the precipitate was indicative of corrosion of the Type 430 carrier, and that corrosion could impact efficacy results. The objective of this study was to compare the suitability of AISI Type 430 to Type 304 stainless steel carriers for evaluating PAA-based disinfectants using the QCT-2 method. Type 304 is more corrosion-resistant than Type 430, is ubiquitous in healthcare environments, and is used in other standard methods. Suitability of the carriers was evaluated by comparing their impacts on efficacy results and PAA degradation rates. In efficacy tests with 1376 ppm PAA, reductions of C. difficile spores after 5, 7 and 10 minutes on Type 430 carriers were at least about 1.5 log10 lower than reductions on Type 304 carriers. In conditions simulating a QCT-2 test, PAA concentration with Type 430 carriers was reduced by approximately 80% in 10 minutes, whereas PAA concentration in the presence of Type 304 carriers remained stable. Elemental analyses of residues on each carrier type after efficacy testing were indicative of corrosion on the Type 430 carrier. Use of Type 430 stainless steel carriers for measuring the efficacy of PAA-based disinfectants should be avoided as it can lead to an underestimation of real life sporicidal efficacy. Type 304 stainless steel carriers are recommended as a suitable

Influência da velocidade de circulação do leite na adesão de Pseudomonas aeruginosa sobre aço inoxidável The speed of milk circulation influences the adhesion of Pseudomonas aeruginosa on stainless steel

Directory of Open Access Journals (Sweden)

Hamilton Mendes de Figueiredo

2009-09-01

Full Text Available A influência da velocidade de circulação do leite na adesão bacteriana de Pseudomonas aeruginosa foi avaliada em teste de uso simulado por meio de um modelo de circuito de processamento de leite. O circuito é composto por uma tubulação de aço inoxidável AISI 304, com 1,9 cm de diâmetro e 5,8 m de comprimento, além de um tanque de 25 L, utilizado como reservatório do produto e das soluções sanitizantes. O reservatório foi acoplado a uma bomba centrífuga de ½ HP, para impulsionar o alimento ou soluções de higienização pelo sistema equipado com cupons de prova em aço inoxidável nas formas cilíndrica, cotovelo 90º e T. As velocidades de circulação foram de 0,5, 1,0 e 1,5 m.s-1, correspondentes a fluxo turbulento com número de Reynolds de 14.000, 28.000 e 42.000, respectivamente. Quando se utilizou velocidade de 0,5 m.s-1, permaneceram aderidas à superfície 10,7% das células. Já nas velocidades e 1,0 e 1,5 m.s-1 as porcentagens de adesão foram de 5,36 e 4,9%, respectivamente, o que demonstra uma menor remoção de células aderidas à medida que o fluxo diminui, permitindo assim que mais células permaneçam aderidas na linha de produção, o que pode favorecer a formação de biofilmes.The influence of the flow milk circulation in the bacterial adhesion of Pseudomonas aeruginosa was evaluated by simulation tests through a circuit model of milk processing. The circuit is composed of a tubulation of stainless steel AISI 304, with 1.9 cm of diameter, 5.8 m of length and a tank of 25 L used as the reservoir of the product and sanitizer solutions. The reservoir was coupled to a centrifugal bomb of ½ HP to impel the food or sanitizer solutions for the system equipped with 90º and T cylindrical stainless steel specimens. The speed of circulation values were 0.5, 1.0 and 1.5 m.s-1, corresponding to turbulent flow with number of Reynolds 14.000, 28.000 and 42.000, respectively. When flow of 0.5 m.s-1 was used 10.7% the

Una herramienta para la selección automatizada de aceros en el contexto de la Ingeniería Mecánica

Directory of Open Access Journals (Sweden)

L. Dumitrescu

2010-01-01

Full Text Available El diseño de Ingeniería de un producto o componente constituye una actividad difícil, compleja y multidisciplinaria, enfocada a la resolución de problemas. En el presente trabajo se muestra el desarrollo de una herramienta automatizada para la selección de los aceros más utilizados en la construcción de maquinarias. La herramienta constituye una ayuda para la selección de los materiales desde la etapa conceptual del proceso de diseño, donde se identifican las diferentes categorías de materiales a utilizar. La herramienta comprende las características y propiedades más relevantes de los aceros de Ingeniería disponibles en seis normas internacionales: Japonesa (JIS, Alemana (DIN, Vbn, DIN-Vbn, Rusa (GOST, Americana (AISI, SAE, AISI-SAE, ASTM, Inglesa (BS, EN, GB, Francesa (AFNOR y la Norma Cubana (NC vigente.The product or component design constitutes a difficult, complex and multidisciplinary activity, focused to the resolution of problems. Presently work show the development of an automated tool for the selection of the more used steels in the construction of machineries. The tool constitute a help for the selection of the materials from the conceptual stage of the design process, where the different categories of materials are identified to use. The tool analyze the characteristics and more common properties of the available steels in six international standards: JIS (Japan, DIN, Vbn, DIN-Vbn (Germany, GOST (Russia, AISI, SAE, AISI-SAE, ASTM (USA, BS, IN, GB (England, AFNOR (France and NC (Cuba.

Estudio del desgaste del flanco de carburos recubiertos y cermet durante el torneado de alta velocidad en seco del acero AISI 1045

Directory of Open Access Journals (Sweden)

Hernández-González, L. W.

2011-06-01

Full Text Available This work deals with the experimental study of the flank wear evolution of two coating carbide inserts and a cermet insert during the dry finishing turning of AISI 1045 steel with 400, 500 and 600 m/min cutting speeds. The results were analyzed using the variance analysis and lineal regression analysis in order to describe the relationship between the flank wear and machining time, obtaining the adjusted model equation. The investigation demonstrated a significant effect of cutting speed and machining time on the flank wear at high speed machining. The three coating layers insert showed the best performance while the two layers insert had the worst behaviour of the cutting tool wear at high cutting speeds.

El objetivo de este trabajo es el estudio experimental de la evolución del desgaste del flanco respecto al tiempo de dos insertos de carburo recubiertos y un cermet durante el torneado de acabado en seco del acero AISI 1045 con velocidades de corte de 400, 500 y 600 m/min. Los resultados fueron comparados utilizando el análisis de varianza y el análisis de regresión lineal para describir la relación entre el desgaste del flanco y el tiempo de maquinado, obteniéndose la ecuación del modelo ajustado. La investigación demostró un efecto significativo de la velocidad de corte y del tiempo de maquinado en el desgaste del flanco en el maquinado de alta velocidad. El mejor desempeño se obtuvo para el carburo recubierto con tres capas, mientras que el carburo con dos capas sufrió el mayor desgaste a elevadas velocidades de corte.

The LCF behaviour of SS AISI 304 in the temperature range between 450 deg. C and 850 deg. C in connection with life time predictions

International Nuclear Information System (INIS)

Bocek, M.; Petersen, C.; Schmitt, R.

The lifetime in high amplitude strain cycling with tensional hold periods is analysed presuming that creep failure damage is life determining. The life fraction rule (LFR) is used to calculate the lifetime consumpted during the dwell period in strain controlled tests as well as during tensional hold time stress cycles. It follows from the present investigation that stress relaxation occurring during the strain hold periods has a dominant influence upon the lifetime. The damage in stress relaxation is calculated by means of the LFR and the results are compared to experiments conducted on Zircaloy-4 (T=600 deg. C) and the austenitic stainless steel Type AISI 304 (T=650 deg. C). From the very good agreement between both it is concluded that under the loading conditions considered, creep failure damage is the main life determining damage contribution. To investigate the contributions of creep and fatigue to failure damage stress controlled experiments were conducted on AISI 304 at 550 deg. C and 850 deg. C. Whereas at the lower temperature (T 0.6 Tsub(s)) the lifetime increased with decreasing R. Therefrom it is concluded that in the case considered for T>0.6 Tsub(s) fatigue damage is not lifetime determining. (author)

Determinación de las condiciones experimentales óptimas de un acero AISI 4140 nitrurado por plasma postdescarga micro-ondas

Directory of Open Access Journals (Sweden)

Medina-Flores, A.

2005-12-01

Full Text Available AISI 4140 steel pieces were nitrided by an experimental reactor made in laboratory. A series of runs were to carry out to find the correct parameters below the point of transformation eutectoide (590 °C, which a compact, homogeneous and harder nitrided layer was formed on the top of the surface. Several characterizations techniques were used to analize the microsctructural change, such as, optical microscopy (OM, microhardness Vickers, X-Ray diffraction (DRX. The results showed the formation of a compact and homogeneous layer formed by a mixture of ε-Fe_2,3N and γ’-Fe₄N iron nitrides whit an average of 12 μm of thickness. The Vickers results showed a value of 1100 Hv on the top of the surface a concentration profile of microhardness is observed from the top of the surface to the core of the material.

Piezas de acero AISI 4140 fueron nitruradas en un reactor experimental fabricado en el laboratorio. Para determinar los valores de los parámetros ideales de nitruración con los cuáles se obtuvo un mayor espesor, homogeneidad y dureza de la capa nitrurada, se llevaron a cabo una serie de experimentos, a temperaturas por debajo del punto de transformación eutectoide (590 °C. Para determinar el cambio microestructural de las muestras nitruradas, se analizaron, mediante diferentes técnicas de caracterización tales como microscopía óptica (MO, microdureza Vickers y difracción de rayos X (DRX. Los resultados mostraron la formación de una capa compacta y homogénea de 12 μm de espesor formada por los nitruros ε-Fe_2,3N y γ’-Fe₄N sobre la superficie del material. Los resultados de microdureza vickers mostraron un valor máximo de 1.100 Hv sobre la capa nitrurada observándose un perfil de microdureza de la superficie hacia el interior del material.

EFICACIA DE LA PREPARACIÓN BIOMECÁNICA DE CONDUCTOS RADICULARES EN EL CRECIMIENTO MICROBIOLÓGICO EN PIEZAS DENTARIAS ANTERIORES CON NECROSIS PULPAR EN PACIENTES DE LA CLÍNICA ODONTOLÓGICA UANCV. JULIACA, PUNO. 2013

OpenAIRE

TAPIA CONDORI, RILDO PAÚL

2015-01-01

RESULTADOS TABLAS DE INFORMACIÓN GENERAL TABLAS QUE RESPONDEN A LOS OBJETIVOS MICROBIOLOGÍA ENDODÓNTICA VÍAS MICROBIANAS DE ACCESO TÚBULOS DENTINARIOS CAVIDAD ABIERTA MEMBRANA PERIODONTAL REQUERIMIENTOS PARA UN PATÓGENO ENDODÓNTICO POTENCIAL DE OXIDO-REDUCCIÓN ANTAGÓNICOS INTERMICROBIANOS NECROSIS PULPAR TIPOS DE NECROSIS PREPARACIÓN BIOMECÁNICA EN PIEZAS CON NECROSIS PULPAR INSTRUMENTOS CONVENCIONALES DE ACERO INOXIDABLE CARACTERÍSTICAS DE LAS LIMAS K DE ACERO INOXIDABLE PROPIEDADES FÍSICAS ...

Study of the polarization for Incoloy 800 and for the stainless stell AISI 304 in mixtures of Iron, Nickel and Chromium Chlorides

International Nuclear Information System (INIS)

Travalloni, A.M.; Sathler, L.; Mattos, O.R.

1985-01-01

Polarization curves for the Incoloy 800 and for the stainless stell AISI 304 were obtained with static and rotational electrodes. The electrolytes employed showed growing concentrations of mixtures as Iron, Nickel and Chromium Chlorides their proportion being the same as the content of these elements in the respective alloys. The alloys under investigation exhibited a continuous transition behaviour from the passive to the active-passive and to the active conditions. Also, the pH was found the main parameter controlling the anodic behaviour of the alloy. (Author) [pt

Mechanical behavior of AISI 304SS determined by miniature test methods after neutron irradiation to 28 dpa

Energy Technology Data Exchange (ETDEWEB)

Rabenberg, Ellen M.; Jaques, Brian J. [Department of Materials Science and Engineering, Boise State University, 1910 University Dr., Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States); Sencer, Bulent H. [Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States); Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Garner, Frank A. [Radiation Effects Consulting, 2003 Howell Ave., Richland, WA 99354 (United States); Freyer, Paula D. [Westinghouse Electric Company LLC, Pittsburgh, PA 15235 (United States); Okita, Taira [Research Into Artifacts Dept., Center for Engineering, University of Tokyo, Tokyo (Japan); Butt, Darryl P., E-mail: DarrylButt@BoiseState.edu [Department of Materials Science and Engineering, Boise State University, 1910 University Dr., Boise, ID 83725 (United States); Center for Advanced Energy Studies, 995 University Blvd., Idaho Falls, ID 83401 (United States)

2014-05-01

The mechanical properties of AISI 304 stainless steel irradiated for over a decade in the Experimental Breeder Reactor (EBR-II) were measured using miniature mechanical testing methods. The shear punch method was used to evaluate the shear strengths of the neutron-irradiated steel and a correlation factor was empirically determined to predict its tensile strength. The strength of the stainless steel slightly decreased with increasing irradiation temperature, and significantly increased with increasing dose until it saturated above approximately 5 dpa. An effective tensile strain hardening exponent was also obtained from the data which shows a relative decrease in ductility of steel with increased irradiation damage. Ferromagnetic measurements were used to observe and deduce the effects of the stress-induced austenite to martensite transformation as a result of shear punch testing.

Inductive plasma source for the ion treatment of AISI-304 SS

International Nuclear Information System (INIS)

Piedad-Beneitez, A de la; Lopez-Callejas, R; Granda-Gutierrez, E E; Rodriguez-Mendez, B G; Perez-Martinez, J A; Flores-Fuentes, A A; Valencia-Alvarado, R; Barocio, S R; Mercado-Cabrera, A; Pena-Eguiluz, R; Munoz-Castro, A E

2008-01-01

The design and construction of a simple inductive plasma source is described as constituted by an evacuated Pyrex glass cylinder reactor with 190 mm inner diameter and 500 mm length. This discharge vessel is coaxially surrounded by a cylindrically wound antenna, 240 mm in diameter, made of 3.2 mm wide copper wire. The antenna is supplied by a 13.56 MHz RF generator whose resulting electric field is able to create the plasma. When nitrogen is admitted to the vessel, the plasma generation takes place within the 0.1-50 Pa work pressure and 300-600 W RF power. The plasma density has been established by double Langmuir probes between 3.2 x 10 15 and 2.4 x 10 18 m -3 . This inductive plasma set up is meant to modify the surface of AISI-304 stainless steel by means of ion deposition, thanks to the sample bias provided by an external - 400 V dc supply, in order to improve the steel hardness without compromising its corrosion resistance. Once accelerated by the negative bias, the plasma ions impinge on the sample nitriding it by diffusion. The treated samples were characterized by x-ray diffraction (XRD) indicating the formation of the expanded gamma phase, by scanning electron microscopy (SEM) providing the atomic percentages of nitrogen, and by microhardness (HV) measurement.

Intergranular stress corrosion in soldered joints of stainless steel 304

International Nuclear Information System (INIS)

Zamora R, L.

1994-01-01

The intergranular stress cracking of welded joints of austenitic stainless steel, AISI 304, is a serious problem in BWR type reactors. It is associated with the simultaneous presence of three factors; stress, a critical media and sensibilization (DOS). EPR technique was used in order to verify the sensibilization degree in the base metal, and the zone affected by heat and welding material. The characterization of material was done. The objective of this work is the study of microstructure and the evaluation of EPR technique used for the determination of DOS in a welded plate of austenitic stainless steel AISI 304. (Author)

Viabilidad de nuevos materiales frente a materiales convencionales en la construcción de pantalanes

OpenAIRE

Marín Gallego, Enric

2012-01-01

Este proyecto estudia la viabilidad de nuevos materiales estructurales, tales como los materiales compuestos, comparándolos con materiales convencionales como el acero, el acero inoxidable o el hormigón.

Influencia del material de aporte en la resistencia a corrosión por picadura en uniones soldadas de un acero inoxidable dúplex 2205

Directory of Open Access Journals (Sweden)

Múnez, C. J.

2007-08-01

Full Text Available In this work, it has been studied the pitting corrosion resistance of welding duplex stainless steel 2205. Unions were made by GMAW process with different fillers: duplex ER 2209 and two austenitic (ER 316LSi and ER 308LSi. The microstructure obtained with the duplex ER 2209 filler is similar to the duplex 2205 base material, but the unions produced with the austenitic fillers cause a decrease of the phases relation a/g. To evaluate the influence of the filler on the weld, the pitting corrosion resistance was determined by electrochemical critical pitting temperature test (TCP and the mechanical properties by the hardness. The phases imbalance produced for the dissimilar fillers bring out a variation of the pitting corrosion resistance and the mechanical properties.

En este trabajo se ha estudiado la resistencia a la corrosión localizada por picadura, de soldaduras realizadas sobre un acero inoxidable dúplex 2205. Se hicieron uniones mediante el proceso GMAW, utilizando como material de aporte un hilo dúplex ER 2209 y dos austeníticos ER 316LSi y ER 308LSi. Metalúrgicamente, se observa como para el hilo ER 2209 las microestructuras que se obtienen son similares a la del dúplex 2205, mientras que en las uniones con hilo austenítico, pueden verse microestructuras muy diferentes en las que la relación de fases a/g disminuye. Al evaluar la resistencia a la corrosión por picadura, mediante la Temperatura Crítica de Picadura (TCP, se comprobó como el desequilibrio entre las fases, generado por el aporte, provoca la variación en la resistencia a la corrosión localizada por picadura. También, se estudió la variación en las propiedades mecánicas del material mediante ensayos de dureza.

Diffusional Growth Kinetics Analisys of Fe2B Layers Applied During the Coating Powder-Pack Boriding Process on an AISI 1026 Steel

Directory of Open Access Journals (Sweden)

M. Elias-Espinosa

2015-01-01

Full Text Available La exigencia de emplear materiales con propiedades avanzadas incluyen la necesidad de aplicar recubrimientos de alta resistencia que alarguen la vida de útil de aceros comerciales, de esta forma, el tratamiento termoquímico de borurización tiene el potencial para cumplir estos requerimientos. En este trabajo de investigación se formula un modelo matemático para analizar la cinética de crecimiento de las capas de 2 Fe B formadas sobre la superficie de un acero AISI 1026. El modelo matemático propuesto se desarrolló en base a la solución de la ecuación de balance de masa de la interface de crecimiento 2 Fe B/Fe para evaluar el coeficiente de difusión del boro a través de las capas de Fe2B en un rango de temperaturas de 1123 a1273 K. En el modelo desarrollado se incluyó el tiempo de incubación del boruro para formar la fase Fe2B. El modelo matemático fue validado con datos experimentales realizados a una temperatura de 1253 K y tiempo de siete horas. Las capas de boruro fueron caracterizadas y analizadas por microscopia óptica y de barrido (se obtuvo un EDS, así como por Difracción de Rayos – X (XRD. Se utilizó la técnica de indentación Daimler-Benz Rockwell-C para evaluar cualitativamente la adherencia de la capa de Fe2B sobre el sustrato (acero AISI 1026. Para usos prácticos y para un espesor determinado, se propuso un diagrama a espesor constante (215 μm el cual es controlado con la variación de la temperatura y tiempo de exposición al recubrimiento. De los resultados obtenidos, se encontró que la energía de activación para el boro en el acero AISI 1026 es igual a 178 kJ mol-1.

Some Temperature Effects on AISI-304 Nitriding in an Inductively Coupled RF Plasma

International Nuclear Information System (INIS)

Valencia-Alvarado, R.; Barocio, S. R.; Mercado-Cabrera, A.; Pena-Eguiluz, R.; Munoz-Castro, A. E.; Piedad-Beneitez, A. de la; Rosa-Vazquez, J. de la; Lopez-Callejas, R.; Godoy-Cabrera, O. G.

2006-01-01

Some recent results obtained from nitriding AISI 304 stainless steel samples, 1.2 cm in diameter and 0.5 cm thick are reported here in the case of an 85% hydrogen and 15% nitrogen mixture work gas. The process was carried out from 300 to 400 W for (13.56 MHz) inductively coupled plasma within a 60 cm long pyrex glass tube 3.5 cm in diameter where the samples were biased up to -300 V with respect to earth. The resulting hardness appears to be a function of the substrate temperature which varied from 200 deg. C at a 0 V bias to 550 deg. C at -300 V. The plasma density at 400 W reached 3x1010 cm-3 with a 4 eV electron temperature. Prior to nitriding, all the samples were polished with 0.05 μm diamond paste, leading to a 30 nm average roughness (Ra). After nitriding at -300 V, the Ra rose until ∼400 nm while hardness values of 1500 HV under 300 g loads were measured. X ray diffraction indicates that the extended phase amplitude (γN), Fe and Cr nitride depends on the substrate temperature

Evaluación de un procedimiento de soldadura para el AISI 4130 sin PWHT bajo normas API 6A y ASME Sección IX

OpenAIRE

Naranjo, Carlos; Sánchez, Xavier; Morales, Juan

2014-01-01

Resumen— Debido a la complejidad de realizar postcalentamiento en campo necesario para garantizar las propiedades mecánicas de una junta soldada de acero AISI 4130 de acuerdo con las normas API 6A [1] y ASME Sección IX[2], y evitar la presencia de martensita en la estructura metalográfica de la junta, siendo esta última perjudicial en los aceros y provocada por enfriamientos rápidos. Se ve la necesidad de desarrollar un procedimiento de soldadura capaz de satisfacer mencionadas condiciones si...

Small angle neutron scattering study of the damage induced by creep deformation in AISI 304 stainless steel

International Nuclear Information System (INIS)

Boeuf, A.; Coppola, R.; Matera, R.; Rustichelli, F.; Zambonardi, F.; Puliti, P.; Melone, S.

1982-01-01

In the austenitic stainless steels, a class of materials largely used in the nuclear power plants, creep induces essentially two new microstructural effects: the nucleation and growth of grain boundary cavities and the precipitation of carbides. Carbides precipitate as a consequence of pure thermal treatment, whereas for the occurrence of voids the presence of stress is necessary. It should be noted however, that the kinetics of precipitation and even the precipitate crystal structure are changed by the introduction of dislocations due to straining during creep. The aim of the present study is a quantitative characterization of the creep damage occurring in a stainless steel of the type X 6 CrNi 8 11 (AISI 304). The experimental techniques used are optical and electron microscopy, microprobe analysis and small angle neutron scattering. This latter technique is described in more detail

The Cementation of Boron to Steels by the Method of Electrolytic Deposition; Cementation Electrolytique d'Aciers par le Bore; Tsementirovanie bora v stali putem ehlektroliticheskogo osazhdeniya; Cementacion de Aceros con Boro por Deposito Electrolitico

Energy Technology Data Exchange (ETDEWEB)

Kawakami, M. [Tokyo Institute of Technology (Japan)

1964-06-15

aceros al carbono, aceros inoxidables, acero de elevado contenido de cromo, etc.; todos ellos dan resultados satisfactorios. (author) [Russian] Privoditsja metod izgotovlenija upravljajushhego sterzhnja s cementirovaniem bora. Jetot process osushhestvljaetsja posredstvom jelektroliza rasplavlennogo tetrabornokislogo natrija pri temperature okolo 900 Degree-Sign S . Obrabatyvaemyj stal'noj sterzhen' sluzhit katodom, v k a chestve anoda ispol'zuetsja grafitovyj jelektrod. V processe jelektroliza bor osazhdaetsja na stal'noj sterzhen' i diffundiruet v sta l'. Pri podhodjashhih uslovijah jelektroliza legko udaetsja poluchit' stal'noj sterzhen', soderzhashhij po 20% bora. Issledovalis' sledujushhie tipy stali: uglerodistaja, nerzhavejushhie, hromistaja i t.d. , vo vseh sluchajah byli polucheny polozhitel'nye rezul'taty. (author)

DISEÑO DE UN PROTOTIPO FERMENTADOR DE LECHE SEMIAUTOMÁTICO PARA LA ELABORACIÓN DE SUERO COSTEÑO

Directory of Open Access Journals (Sweden)

BASHIR YACUB B.

Full Text Available El Suero Costeño es un producto lácteo fermentado, artesanalmente en la costa atlántica colombiana. Para cumplir con las normas sanitarias el fermentador está constituido por un tanque diseñado y fabricado en acero inoxidable 304, con un volumen neto de 30 L. Se garantizó una temperatura de 35°C en la fermentación de la leche, con un sistema de enfriamiento mediante una chaqueta. La temperatura se medió con un sensor de temperatura, tipo PT-100, con el sistema microcontrolado se programó su set-point, para separar el espiche del suero se utilizó una válvula; la finalización de la fermentación se determinó con la medición del pH con un pH-metro. La cantidad de materia prima y producto se mide con un sensor de nivel y se muestra de manera continua en la pantalla LCD del panel de control.

Susceptibility to stress corrosion in stainless steels type AISI 321 and 12X18H10T used in PWR type reactors (WWER); Susceptibilidad a la corrosion bajo esfuerzo de barras de acero inoxidable AISI 321 y 12X18H10T en ambientes utilizados en reactores VVER

Energy Technology Data Exchange (ETDEWEB)

Matadamas C, N

1996-12-31

Titanium stabilized stainless steels have been utilized in sovietic pressurized water reactors (VVER) for avoid the susceptibility to Intergranular Corrosion (IGC) present in other austenitic stainless steels. However the Intergranular Corrosion resistance of this kind of materials has been questioned because of Intergranular Stress Corrosion Cracking failures (IGSCC) have been reported. This paper study the electrochemical behavior of the AISI 321 stainless steel in a H{sub 3}BO{sub 3} Solution contaminated with chlorides and its susceptibility to Intergranular Corrosion.Electrochemical prediction diagrams of the stainless steels AISI 321 and 12X18H10T (sovietic) sensitized (600 Centigrade, 3 h.) were compared. Cylindrical and conical samples were used in Slow Strain Rate Tests (SSRT), to determine the susceptibility to Stress Corrosion Cracking (SCC) in AISI 321 and 12X18H10T stainless steels. The results obtained showed that the temperature of the solution is a very important factor to detect this susceptibility. Fractography studies on the fracture surfaces of the samples obtained in the SSRT at high temperature were realized. Corrosion velocities of both AISI 321 and 12X18H10T stainless steels were determined using conical samples in the CERT system at high temperature. E.D.A.X. analysis was employed in both AISI 321 and 12X18H10T stainless steels in order to explain the degree of sensitization. (Author).

Desarrollo de aceros reforzados con carburos primarios vía metalurgia líquida

Directory of Open Access Journals (Sweden)

Agote, I.

2005-12-01

Full Text Available The steel reinforcement by means of the addition of primary carbides via liquid metallurgy needs to fulfill two essential requirements to be technically viable: the development of a solid reinforcing product which is appropriate to be mixed with the steel and the optimization of the metallurgic addition of these reinforcing particles into the liquid steel. Besides, the improvement of the reinforced alloy characteristics is directly related to the particles' nature of reinforcing particles, their homogeneous and uniform distribution in the matrix and their size and morphology. The manufacture of these carbides by SHS ('Self propagating High temperature Synthesis' and their addition before steel is poured into moulds allows achieving the above-mentioned conditions.

Para que el reforzamiento de los aceros con carburos primarios vía metalurgia líquida sea técnicamente viable se requiere del desarrollo de un tipo de producto reforzante sólido, adecuado para su incorporación al acero, así como de la optimización de dicha vía metalúrgica de adición del producto reforzante al material base en estado líquido. Además, la mejora de características de la aleación reforzada es función directa de la naturaleza de las partículas, de su homogénea y uniforme distribución en la matriz y del tamaño y morfología regular de las mismas. Estas condiciones se consiguen cuando las partículas de carburo se elaboran previamente mediante la técnica SHS (selfpropagating high temperature synthesis y se añaden al baño de acero líquido previo a su colada en moldes o lingoteras.

Parametric optimization during machining of AISI 304 Austenitic Stainless Steel using CVD coated DURATOMIC cutting insert

Directory of Open Access Journals (Sweden)

M. Kaladhar

2012-08-01

Full Text Available In this work, Taguchi method is applied to determine the optimum process parameters for turning of AISI 304 austenitic stainless steel on CNC lathe. A Chemical vapour deposition (CVD coated cemented carbide cutting insert is used which is produced by DuratomicTM technology of 0.4 and 0.8 mm nose radii. The tests are conducted at four levels of Cutting speed, feed and depth of cut. The influence of these parameters are investigated on the surface roughness and material removal rate (MRR. The Analysis Of Variance (ANOVA is also used to analyze the influence of cutting parameters during machining. The results revealed that cutting speed significantly (46.05% affected the machined surface roughness values followed by nose radius (23.7%. The influence of the depth of cut (61.31% in affecting material removal rate (MRR is significantly large. The cutting speed (20.40% is the next significant factor. Optimal range and optimal level of parameters are also predicted for responses.

Local behavior of an AISI 304 stainless steel submitted to in situ biaxial loading in SEM

Energy Technology Data Exchange (ETDEWEB)

Caër, C., E-mail: celia.caer@gmail.com; Pesci, R.

2017-04-06

The microstructural response of a coarse grained AISI 304 stainless steel submitted to biaxial tensile loading was investigated using SEM and X-ray diffraction. The specimen geometry was designed to allow for biaxial stress state and incipient crack in the center of the active part under biaxial tensile loading. This complex loading was performed step by step by a micromachine fitting into a SEM chamber. At each loading step FSD pictures and EBSD measurements were carried out to study the microstructural evolution of the alloy, namely grain rotations and misorientations, stress-induced martensite formation and crack propagation. According to their initial orientation, grains are found to behave differently under loading. Approximately 60% of grains are shown to reorient to the [110] Z orientation under biaxial tensile loading, whereas the 40% left undergo high plastic deformation. EBSD and XRD measurements respectively performed under loading and on the post mortem specimen highlighted the formation of about 4% of martensite.

T.I.G. Welding of stainless steel. Numerical modelling for temperatures calculation in the Haz; Soldadura T.I.G. de acero inoxidable. Modelo numerico para el calculo de temperaturas en la ZAT

Energy Technology Data Exchange (ETDEWEB)

Martinez-Conesa, E. J.; Estrems-Amestoy, M.; Miguel-Eguia, V.; Garrido-Hernandez, A.; Guillen-Martinez, J. A.

2010-07-01

In this work, a numerical method for calculating the temperature field into the heat affected zone for butt welded joints is presented. The method has been developed for sheet welding and takes into account a bidimensional heat flow. It has built a computer program by MS-Excel books and Visual Basic for Applications (VBA). The model has been applied to the TIG process of AISI 304 stainless steel 2mm thickness sheet. The welding process has been considered without input materials. The numerical method may be used to help the designers to predict the temperature distribution in welded joints. (Author) 12 refs.

Caracterização microestrutural de soldas dissimilares dos aços ASTM A-508 e AISI 316L Characterization of dissimilar metal weld between low alloy steel ASTM A-508 and 316L stainless steel

Directory of Open Access Journals (Sweden)

Luciana Iglésias Lourenço Lima

2010-06-01

Full Text Available As soldas dissimilares (dissimilar metal welds - DMWs são utilizadas em diversos segmentos da indústria. No caso específico de usinas nucleares, tais soldas são necessárias para conectar tubulações de aço inoxidável com componentes fabricados em aços baixa liga. Os materiais de adição mais utilizados neste tipo de solda são as ligas de níquel 82 e 182. Este trabalho consistiu na soldagem de uma junta dissimilar de aço baixa liga ASTM A-508 G3 e aço inoxidável austenítico AISI 316L utilizando as ligas de níquel 82 e 182 como metais de adição. A soldagem foi realizada manualmente empregando os processos de soldagem ao arco SMAW (Shielded Metal Arc Welding e GTAW (Gas Tungsten Arc Welding. Os corpos de prova foram caracterizados microestruturalmente utilizando-se microscópio óptico e microscópio eletrônico de varredura com microanálise por dispersão de energia de raios X (EDS e ensaios de microdureza Vickers. Observou-se uma microestrutura constituída de dendritas de austenita com a presença de precipitados com formas e dimensões definidas pelo aporte térmico e pela direção de soldagem. Não houve variação significativa da dureza ao longo da junta soldada, demonstrando a adequação dos parâmetros de soldagem utilizados.The dissimilar metal welds (DMWs are used in several areas of the industries. In the nuclear power plant, this weld using nickel alloy welding wires is used to connect stainless steel pipes to low alloy steel components on the reactor pressured vessels. The filler materials commonly used in this type of weld are nickel alloys 82 and 182.. In this study, dissimilar metal welds composed of low alloy steel ASTM A-508 G3, nickel alloys 82 e 182 as weld metals, and austenitic stainless steel AISI 316L were prepared by manual shielded metal arc welding (SMAW and gas tungsten arc welding techniques (GTAW. Samples were microstructural characterized by optical microscopy and scanning electron microscopy

Effect of acetic acid on corrosion behavior of AISI 201, 304 and 430 stainless steels

Energy Technology Data Exchange (ETDEWEB)

Vashishtha, Himanshu; Taiwade, Ravindra V.; Sharma, Sumitra [Visvesvaraya National Institute of Technology (VNIT), Nagpur (India). Dept. of Metallurgical and Materials Engineering

2017-05-15

Austenitic stainless steels are often used to handle organic acids such as acetic acid (CH{sub 3}COOH), which are extensively used in food contact applications and chemical industries for manufacturing medicines, nutrition and various chemical amalgams. In the present investigation an attempt has been made to compare the corrosion behavior of Cr-Ni (AISI type 304), Cr-Mn-Ni (type 201) and Cr (type 430) stainless steel for economical replacement of higher cost Cr-Ni grade. Immersion testing was performed at room temperature and boiling temperature in acetic acid. Atomic absorption spectroscopy was carried out to evaluate metal ion concentration in the immersion solution. The surface morphology of pit formation was characterized using scanning electron microscopy coupled with energy dispersive X-ray spectroscopy. The effect of elemental leaching on electrical conductivity of the immersion solution was evaluated and correlated with pH measurements. A new mechanism has been proposed for the pit formation due to manganese sulfide inclusions. The replacement compatibility was further confirmed with anodic polarization testing and a successful replacement was established for room temperature applications.

Revisiting Formability and Failure of AISI304 Sheets in SPIF: Experimental Approach and Numerical Validation

Directory of Open Access Journals (Sweden)

Gabriel Centeno

2017-11-01

Full Text Available Single Point Incremental Forming (SPIF is a flexible and economic manufacturing process with a strong potential for manufacturing small and medium batches of highly customized parts. Formability and failure in SPIF have been intensively discussed in recent years, especially because this process allows stable plastic deformation well above the conventional forming limits, as this enhanced formability is only achievable within a certain range of process parameters depending on the material type. This paper analyzes formability and failure of AISI304-H111 sheets deformed by SPIF compared to conventional testing conditions (including Nakazima and stretch-bending tests. With this purpose, experimental tests in SPIF and stretch-bending were carried out and a numerical model of SPIF is performed. The results allow the authors to establish the following contributions regarding SPIF: (i the setting of the limits of the formability enhancement when small tool diameters are used, (ii the evolution of the crack when failure is attained and (iii the determination of the conditions upon which necking is suppressed, leading directly to ductile fracture in SPIF.

Welding of AA1050 aluminum with AISI 304 stainless steel by rotary friction welding process

Directory of Open Access Journals (Sweden)

Chen Ying An

2010-09-01

Full Text Available The purpose of this work was to assess the development of solid state joints of dissimilar material AA1050 aluminum and AISI 304 stainless steel, which can be used in pipes of tanks of liquid propellants and other components of the Satellite Launch Vehicle. The joints were obtained by rotary friction welding process (RFW, which combines the heat generated from friction between two surfaces and plastic deformation. Tests were conducted with different welding process parameters. The results were analyzed by means of tensile tests, Vickers microhardness, metallographic tests and SEM-EDX. The strength of the joints varied with increasing friction time and the use of different pressure values. Joints were obtained with superior mechanical properties of the AA1050 aluminum, with fracture occurring in the aluminum away from the bonding interface. The analysis by EDX at the interface of the junction showed that interdiffusion occurs between the main chemical components of the materials involved. The RFW proves to be a great method for obtaining joints between dissimilar materials, which is not possible by fusion welding processes.

Corrosion Behavior of Ti/TiN Film Coated on AISI 304 Stainless Steel

Energy Technology Data Exchange (ETDEWEB)

Choe, Han Cheol [Kwangyang College, Gwangyang (Korea, Republic of); Park, Ji Yoon; Kim, Kwan Hyu [Chonnam National University, Gwangju (Korea, Republic of)

2000-06-15

Effects of the Ti content and the presence of Ti underlayer on the corrosion behaviors of TiN coated AISI 304 stainless steel have been studied. The stainless steel containing 0.1{approx}1.0 wt% Ti were melted with a vacuum furnace and heat treated at 1050 .deg. C for 1hr for solutionization. The specimens were coated with Ti and TiN with thickness of 1 {mu}m and 2 {mu}m respectively by electron-beam physical vapour deposition (EB-PVD) method. The microstructures and phase analysis were conducted by using SEM and WDS. The coated films showed fine columnar structure. The corrosion potential obtained from the anodic polarization curves measured in H{sub 2}SO{sub 4} solution increased in proportion to the Ti content of substrate and was much higher in the specimen coated with Ti underlayer compared to the specimen without Ti underlayer. The potential-time and the current-time curves which were obtained in 0.1M H{sub 2}SO{sub 4} + 0.1M HCI solution showed that both the increase in Ti content and the presence of Ti underlayer increased the potential and decreased the current density resulting in a dense passive film and a suppress of pit formation respectively.

Cobre antimicrobiano contra patógenos intrahospitalarios en Perú

Directory of Open Access Journals (Sweden)

Edwin Neciosup

2015-01-01

Full Text Available Introducción: Las infecciones intrahospitalarias (IIH constituyen un problema de salud pública que generan grandes gastos por parte de los gobiernos, debido a que los patógenos causantes de IIH presentan resistencia a fármacos y generan una mayor permanencia de los pacientes, pues la infraestructura hospitalaria constituye un reservorio favorable para los patógenos. Las superficies de cobre surgen como opción sanitaria y efectiva para controlar el crecimiento y propagación de estos patógenos. Objetivos: Evaluar la actividad bactericida de las superficies de cobre contra los principales bacterias patógenas causantes de IIH (Escherichia coli, Pseudomonas aeruginosa y Staphylococcus aureus. Diseño: Estudio experimental con muestreo no probabilístico. Lugar: Hospital Regional Docente las Mercedes (HRDLM y Hospital Provincial Docente Belén (HPDB, Lambayeque, Perú. Materiales: Nueve cepas bacterianas, 3 de E. coli , 3 de P. aeruginosa y 3 de S. aureus; superficies metálicas (1 cm² de cobre y acero inoxidable (control . Intervenciones: Las 9 cepas bacterianas fueron proporcionadas por los hospitales HRDLM (4 cepas y HPDB (5 cepas. Los análisis de ANOVA y de Tukey fueron aplicados para evaluar la actividad bactericida de las superficies de cobre y acero inoxidable contra las 9 cepas causantes de IIH, usando los programas estadísticos Minitab y Sigmaplot, respectivamente. Principales medidas de resultados: Diferencias en el crecimiento bacteriano sobre superficies de cobre o acero inoxidable, con respecto al tiempo de exposición. Resultados: Las 9 cepas -3 de P. aeruginosa, 3 de E. coli y 3 de S. aureus - expuestas a superficies de cobre fueron eliminadas en 10, 15 y 60 minutos, respectivamente. La carga bacteriana de las células expuestas en superficies de acero inoxidable permaneció constante y viable por periodos mayores a 60 minutos. Además, las superficies de cobre eliminaron más rápido a las bacterias Gram negativas (P

Application of Deep Cryogenic Treatment to Uncoated Tungsten Carbide Inserts in the Turning of AISI 304 Stainless Steel

Science.gov (United States)

Özbek, Nursel Altan; Çİçek, Adem; Gülesİn, Mahmut; Özbek, Onur

2016-12-01

This study investigated the effects of deep cryogenic treatment (DCT) on the wear performance of uncoated tungsten carbide inserts. AISI 304 austenitic stainless steel, widely used in industry, was selected as the workpiece material. Cutting experiments showed that the amount of wear significantly increased with increasing cutting speed. In addition, it was found that DCT contributed to the wear resistance of the turning inserts. The treated turning inserts were less worn by 48 and 38 pct in terms of crater wear and notch wear, respectively, whereas they exhibited up to 18 pct superior wear performance in terms of flank wear. This was attributed to the precipitation of new and finer η-carbides and their homogeneous distribution in the microstructure of the tungsten carbide material after deep cryogenic treatment. Analyses via image processing, hardness measurements, and SEM observations confirmed these findings.

The influence of silicon as a possible reactive element in the protection against high temperature oxidation of AISI 304 stainless steel

International Nuclear Information System (INIS)

Otero, E.; Perez, F.J.; Hierro, M.P.; Gomez, C.; Pedraza, F.; Segovia, J. L. de; Roman, E.

1998-01-01

The influence of silicon incorporated into the alloy by means of ion implantation of 1 x 10''15 ions/cm''2 at 150 keV on the protective scale development based upon Cr 1 ,3 Fe 0 ,7O 3 and manganese-enriched spinels, Mn 1 ,5Cr 1 .5O 4 after oxidation of an austenitic AISI 304 stainless steel at 1.173 K and atmospheric pressure of air for 144 h has been studied. The presence of small quantities of silicon at the outermost layers of the alloy promotes transport of chromium during the early stages of oxidation. Further, ion implantation seems to play a beneficial role against decarburization of the alloy. (Author) 8 refs

Soldagem por Difusão de Aços Inoxidáveis para Fabricação de Trocadores de Calor Compactos

Directory of Open Access Journals (Sweden)

Marcus Vinícius Volponi Mortean

2016-03-01

Full Text Available Resumo A união de materiais diferentes ou componentes com geometrias complexas muitas vezes requer processos de uniões especiais, como por exemplo, uma fonte de energia de alta densidade como laser ou feixe de elétrons para soldagem por fusão ou mesmo um processo de soldagem no estado sólido. Em particular, este trabalho descreve os experimentos recentes da aplicação da soldagem por difusão no estado sólido (SDES para diferentes tipos de aços inoxidáveis: austenítico AISI 316L, duplex UNS 31803 e superduplex UNS 327250. A soldagem por difusão foi realizada sob alto vácuo a 1050 °C, durante 60 minutos, empregando uma pressão uniaxial de 18-35 MPa. A qualidade da união foi avaliada por microscopia óptica e testes mecânicos. Os resultados preliminares indicam a necessidade de otimização dos parâmetros de processo para os aços duplex e superduplex. Os resultados positivos alcançados no presente trabalho permitiram a fabricação de protótipos de trocadores de calor compacto em aço inoxidável, utilizando o novo método de fabricação, desenvolvido por LABTUCAL / UFSC, através do qual o processo de corte a jato de água é aplicado para confeccionar com precisão os canais do núcleo do permutador de calor.

Experimental Determination of Temperature During Rotary Friction Welding of AA1050 Aluminum with AISI 304 Stainless Steel

Directory of Open Access Journals (Sweden)

Eder Paduan Alves

2012-03-01

Full Text Available The purpose of this study was the temperature monitoring at bonding interface during the rotary friction welding process of dissimilar materials: AA1050 aluminum with AISI 304 stainless steel. As it is directly related to the mechanical strenght of the junction, its experimental determination in real time is of fundamental importance for understanding and characterizing the main process steps, and the definition and optimization of parameters. The temperature gradients were obtained using a system called Thermocouple Data-Logger, which allowed monitoring and recording data in real-time operation. In the graph temperature versus time obtained, the heating rates, cooling were analyzed, and the maximum temperature was determined that occurred during welding, and characterized every phases of the process. The efficiency of this system demonstrated by experimental tests and the knowledge of the temperature at the bonding interface open new lines of research to understand the process of friction welding.

Mejoramiento de la resistencia a la corrosión del acero AISI 4140 utilizando multicapas de titanio/nitruro de titanio

Directory of Open Access Journals (Sweden)

Faber Correa

2008-01-01

Full Text Available El acero 4140 se utiliza ampliamente en la fabricación de partes de máquinas con durezas entre 25-35 Rockwell C. Sin embargo, su vida útil se ve limitada por su baja resistencia al desgaste y a la corrosión. Con el fin de mejorar su comportamiento frente a la corrosión se depositaron multicapas de Titanio/Nitruro de Titanio (Ti/TiN sobre substratos de acero 4140 mediante un sistema multi-blanco d.c. magnetrón sputtering a partir de un blanco de Ti de alta pureza (99,99% en una atmósfera de Ar/N2. Con el objeto de estudiar el efecto del número de capas sobre la velocidad de corrosión de las películas depositadas, se crecieron multicapas con 1, 5, 10, 15, y 20 bicapas de [Ti /TiN], manteniendo un espesor total constante de 3 um en todas ellas. Las fases existentes y composición química de los recubrimientos fueron analizados mediante espectroscopía de difracción de rayos X (XRD y espectroscopía de energía dispersiva de rayos X (EDX respectivamente. Las muestras de acero sin y con recubrimiento se caracterizaron además por Espectroscopía de Impedancia Electroquímica (EIS y curvas de polarización Tafel. Se encontró que la velocidad de corrosión tuvo una disminución alrededor del 87% en el acero recubierto con 20 bicapas de Ti/TiN en comparación al acero sin recubrir y del 25% respecto a la muestra recubierta con 1 bicapa, lo cual evidencia el efecto positivo del incremento del período en las películas delgadas basadas en multicapas de Ti/TiN.

Corrosion and microstructural analysis data for AISI 316L and AISI 347H stainless steels after exposure to a supercritical water environment

Directory of Open Access Journals (Sweden)

A. Ruiz

2016-06-01

Full Text Available This article presents corrosion data and microstructural analysis data of austenitic stainless steels AISI 316L and AISI 347H exposed to supercritical water (25 MPa, 550 °C with 2000 ppb of dissolved oxygen. The corrosion tests lasted a total of 1200 h but were interrupted at 600 h to allow measurements to be made. The microstructural data have been collected in the grain interior and at grain boundaries of the bulk of the materials and at the superficial oxide layer developed during the corrosion exposure.

Corrosion resistance of the welded AISI 316L after various surface treatments

Directory of Open Access Journals (Sweden)

Tatiana Liptáková

2014-01-01

Full Text Available The main aim of this work is to monitor the surface treatment impact on the corrosion resistance of the welded stainless steel AISI 316L to local corrosion forms. The excellent corrosion resistance of austenitic stainless steel is caused by the existence of stable, thin and well adhering passive layer which quality is strongly influenced by welding. Therefore surface treatment of stainless steel is very important with regard to its local corrosion susceptibility Surfaces of welded stainless steel were treated by various mechanical methods (grinding, garnet blasting. Surface properties were studied by SEM, corrosion resistance was evaluated after exposition tests in chlorides environment using weight and metalographic analysis. The experimental outcomes confirmed that the mechanical finishing has a significant effect on the corrosion behavior of welded stainless steel AISI 316L.

Joining of Dissimilar alloy Sheets (Al 6063&AISI 304 during Resistance Spot Welding Process: A Feasibility Study for Automotive industry

Directory of Open Access Journals (Sweden)

Reddy Sreenivasulu

2014-12-01

Full Text Available Present design trends in automotive manufacture have shifted emphasis to alternative lightweight materials in order to achieve higher fuel efficiency and to bring down vehicle emission. Although some other joining techniques are more and more being used, spot welding still remains the primary joining method in automobile manufacturing so far. Spot welds for automotive applications should have a sufficiently large diameter, so that nugget pullout mode is the dominant failure mode. Interfacial mode is unacceptable due to its low load carrying and energy absorption capability. Strength tests with different static loading were performed in, to reveal the failure mechanisms for the lap-shear geometry and the cross-tension geometry. Based on the literature survey performed, venture into this work was amply motivated by the fact that a little research work has been conducted to joining of dissimilar materials like non ferrous to ferrous. Most of the research works concentrated on joining of different materials like steel to steel or aluminium alloy to aluminium alloy by resistance spot welding. In this work, an experimental study on the resistance spot weldability of aluminium alloy (Al 6063 and austenitic stainless steel (AISI304 sheets, which are lap joined by using a pedestal type resistance spot welding machine. Welding was conducted using a 45-deg truncated cone copper electrode with 10-mm face diameter. The weld nugget diameter, force estimation under lap shear test and T – peel test were investigated using digital type tensometer attached with capacitive displacement transducer (Mikrotech, Bangalore, Model: METM2000ER1. The results shows that joining of Al 6063 and AISI 304 thin sheets by RSW method are feasible for automotive structural joints where the loads are below 1000N act on them, it is observed that by increasing the spots per unit length, then the joint with standing strength to oppose failure is also increased linearly incase of

Studies on the influence of metallurgical variables on the stress corrosion behavior of AISI 304 stainless steel in sodium chloride solution using the fracture mechanics approach

International Nuclear Information System (INIS)

Khatak, H.S.; Gnanamoorthy, J.B.; Rodriguez, P.

1996-01-01

Stress corrosion data on a nuclear grade AISI type 304 stainless steel in a boiling solution of 5M NaCl + 0.15M Na 2 SO 4 + 3 mL/L HCl (bp 381 K) for various metallurgical conditions of the steel are presented in this article. The metallurgical conditions used are solution annealing, sensitization, 10 pct cold work, 20 pct cold work, solution annealing + sensitization, 10 pct cold work + sensitization, and 20 pct cold work + sensitization. The fracture mechanics approach has been used to obtain quantitative data on the stress corrosion crack growth rates. The stress intensity factor, K I , and J integral, J I , have been used as evaluation parameters. The crack growth rates have been measured using compact tension type samples under both increasing and decreasing stress intensity factors. A crack growth rate of 5 x 10 -11 m/s was chosen for the determination of threshold parameters. Results of the optical microscopic and fractographic examinations are presented. Acoustic signals were recorded during crack growth. Data generated from acoustic emissions, activation energy measurements, and fractographic features indicate hydrogen embrittlement as the possible mechanism of cracking

Microstructure analysis of AISI 304 stainless steel produced by twin-roll thin strip casting process

Institute of Scientific and Technical Information of China (English)

无

2007-01-01

The microstructure of AISI 304 austenite stainless steel fabricated by the thin strip casting process were investigated using optical microscope, scanning electron microscope (SEM), transmission electron microscope (TEM), and X-ray diffraction (XRD).The microstructures of the casting strips show a duplex structure consisting of delta ferrite and austenite. The volume fraction of the delta ferrite is about 9.74vol% at the center and 6.77vol% at the surface of the casting thin strip, in vermicular and band shapes. On account of rapid cooling and solidification in the continuous casting process, many kinds of inclusions and precipitates have been found. Most of the inclusions and precipitates are spherical complex compounds consisting of oxides, such as, SiO2, MnO, Al2O3,Cr2O3,and FeO or their multiplicity oxides of MnO·Al2O3,2FeO·SiO2, and 2MnO·SiO2. Many defects including dislocations and stacking faults have also formed during the rapid cooling and solidification process, which is helpful to improve the mechanical properties of the casting strips.

Facile fabrication of superhydrophobic surfaces from austenitic stainless steel (AISI 304) by chemical etching

Science.gov (United States)

Kim, Jae-Hun; Mirzaei, Ali; Kim, Hyoun Woo; Kim, Sang Sub

2018-05-01

Stainless steels are among the most common engineering materials and are used extensively in humid areas. Therefore, it is important that these materials must be robust to humidity and corrosion. This paper reports the fabrication of superhydrophobic surfaces from austenitic stainless steel (type AISI 304) using a facile two-step chemical etching method. In the first step, the stainless steel plates were etched in a HF solution, followed by a fluorination process, where they showed a water contact angle (WCA) of 166° and a sliding angle of 5° under the optimal conditions. To further enhance the superhydrophobicity, in the second step, they were dipped in a 0.1 wt.% NaCl solution at 100 °C, where the WCA was increased to 168° and the sliding angle was decreased to ∼2°. The long-term durability of the fabricated superhydrophobic samples for 1 month storage in air and water was investigated. The potential applicability of the fabricated samples was demonstrated by the excellent superhydrophobicity after 1 month. In addition, the self-cleaning properties of the fabricated superhydrophobic surface were also demonstrated. This paper outlines a facile, low-cost and scalable chemical etching method that can be adopted easily for large-scale purposes.

Desempeño de insertos de WC recubiertos con nanomulticapas de [TiN/TiAlN]n en el mecanizado del acero endurecido AISI 4340

Directory of Open Access Journals (Sweden)

Luis Henry Moreno

2011-01-01

Full Text Available En el presente trabajo se muestran los resultados de la resistencia al desgaste de insertos de carburo de tungsteno (WC sin recubrir y recubiertos con multinanocapas de [TiN/TiAlN]n con un espesor total promedio del recubrimiento de 4 ¿m, así como de insertos recubiertos con monocapas comerciales de TiCN-Al2O3-TiN (TINAL. Se realizaron ensayos de vida útil, análisis de temperatura en la zona de corte, mediciones de rugosidad superfi cial sobre la pieza y sobre los insertos en la superfi cie de ataque, análisis de huella de contacto entre viruta-insertos y análisis de composición química (EDS. Los ensayos se realizaron sobre piezas de acero AISI 4340 utilizando régimen de corte de acabado y aplicando altas velocidades de corte (HSC. Los resultados de mecanizado de acero, para un recorrido de 8.000 metros con diferentes insertos de carburo de tungsteno (WC, sin recubrimiento y recubiertos presentaron valores de desgaste de 0,117 mm y 0,138 mm; en relación a los insertos recubiertos con 300 y 200 bicapas de TiN/TiAlN, respectivamente. De igual manera, los insertos recubiertos con TINAL exhibieron valores de desgaste de 0,174 mm. Además, los valores de temperatura en la zona de corte y para una velocidad de corte de 176,6 m/mim fueron de 522,6 oC para los recubrimientos con 300 bicapas, de 721,4 oC para aquellos con 200 bicapas, y de 1.327,6 oC para los insertos recubiertos con TINAL. La disminución de la temperatura en la zona de corte, relacionada con un menor coefi ciente de fricción y una menor fuerza de corte, contribuyeron al alargamiento de la vida útil de los insertos.

The influence of cutting speed and feed rate in surface integrity of aisi 1045//Influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero aisi 1045

Directory of Open Access Journals (Sweden)

Mario Jacas-Cabrera

2015-09-01

Full Text Available El objetivo de esta investigación es el estudio de la influencia de la velocidad de corte y la velocidad de avance en la integridad superficial del acero AISI-1045, sometido a un proceso de torneado. Las probetas se sometieron a un tratamiento térmico de recocidos (81 HRB. En el trabajo se empleó un diseño experimental 32, con dos variables a tres niveles experimentales, para un total de nueve experimentos, los que fueron replicados. La integridad superficial fue evaluada con la medición de la rugosidad superficial, las tensiones residuales superficiales, la medición de dureza por nano–indentación y por el análisis de la de formación terciaria. Los resultados determinaron la gran influencia de la velocidad de avance en la rugosidad superficial. La medición de las tensiones residuales mostró la influencia de las variables de corte. Del análisis microestructural se observó la existencia de dos zonas de deformación determinándose que el espesor de la zona endurecida llegó a 50 µm. Palabras claves: integridad superficial, rugosidad superficial, nano-indentación; superficie deformada____________________________________________________________________________AbstractThe aim of this research is to study the influence of cutting speed and feed rate on surface integrity of AISI-1045 subjected to a turning process. The specimens were in annealed condition (81 HRB. A 32 factorial experiment design was employed using low, medium and high levels of the two variables in study, performing 9 experiments with a replica. The surfaces were evaluated through the measurements of surface roughness, surface residual stresses, nano-indentation hardness and analyzing the deformed layer. Results corroborated the great influence of feed rate on surface roughness. The results of the residual stresses have shown the influence of cutting speed as well as feed rate in the behavior of circumferential and axial stress respectively. From the analysis of the

Tensile properties of irradiated and fatigue exposed stainless steel DIN X 6 CrNi 1811 (similar to AISI type 304) plate and welded joints

International Nuclear Information System (INIS)

Vries, M.I. de; Schaaf, B. van der; Elen, J.D.

1979-10-01

Test specimens of plate metal and welded joints of stainless steel DIN 1.4948, which is similar to AISI type 304, have been irradiated at 723 K and 823 K up to fluences of 1.10 23 n.m -2 and 5.10 24 n.m -2 (E > 0.1 MeV). These are representative conditions for the SNR-300 reactor vessel and inner components after 16 years of operation. High-rate (depsilon/dt = 1 s -1 ) tensile tests were performed after fatigue exposure up to various fractions of fatigue life (D) ranging from 5% to 95% at the same temperatures as the nominal temperatures of the irradiation series

Tribological properties of BixTiyOz films grown via RF sputtering on 316L steel substrates

Directory of Open Access Journals (Sweden)

Johanna Parra

2015-01-01

Full Text Available En este trabajo se presentan los resultados obtenidos en el análisis químico superficial, la caracterización morfológica y evaluación de las propiedades tribológicas de recubrimientos de titanato de bismuto amorfo (BixTiyOz depositados sobre sustratos de acero inoxidable 316L utilizando la técnica de pulverización catódica rf. El análisis químico elemental se realizó por medio de espectroscopia de electrones Auger (EEA, la morfología de los recubrimientos se determinó mediante microscopia de fuerza atómica (MFA. Las medidas del coeficiente de fricción y la tasa de desgaste fueron obtenidas mediante pruebas de bola sobre disco. Los análisis de EEA permitieron establecer que los primeros 10 nm de los recubrimientos están formados probablemente por óxidos de Bi4Ti3O12 y Ti2O3, las medidas de AFM indican que los recubrimientos tienen una rugosidad promedio de 22.28nm y un tamaño de grano de 50nm. Finalmente, las pruebas tribológicas establecieron que el coeficiente de fricción y la tasa de desgaste del acero recubierto tiene valores similares al acero desnudo.

The Investigation of Strain-Induced Martensite Reverse Transformation in AISI 304 Austenitic Stainless Steel

Science.gov (United States)

Cios, G.; Tokarski, T.; Żywczak, A.; Dziurka, R.; Stępień, M.; Gondek, Ł.; Marciszko, M.; Pawłowski, B.; Wieczerzak, K.; Bała, P.

2017-10-01

This paper presents a comprehensive study on the strain-induced martensitic transformation and reversion transformation of the strain-induced martensite in AISI 304 stainless steel using a number of complementary techniques such as dilatometry, calorimetry, magnetometry, and in-situ X-ray diffraction, coupled with high-resolution microstructural transmission Kikuchi diffraction analysis. Tensile deformation was applied at temperatures between room temperature and 213 K (-60 °C) in order to obtain a different volume fraction of strain-induced martensite (up to 70 pct). The volume fraction of the strain-induced martensite, measured by the magnetometric method, was correlated with the total elongation, hardness, and linear thermal expansion coefficient. The thermal expansion coefficient, as well as the hardness of the strain-induced martensitic phase was evaluated. The in-situ thermal treatment experiments showed unusual changes in the kinetics of the reverse transformation (α' → γ). The X-ray diffraction analysis revealed that the reverse transformation may be stress assisted—strains inherited from the martensitic transformation may increase its kinetics at the lower annealing temperature range. More importantly, the transmission Kikuchi diffraction measurements showed that the reverse transformation of the strain-induced martensite proceeds through a displacive, diffusionless mechanism, maintaining the Kurdjumov-Sachs crystallographic relationship between the martensite and the reverted austenite. This finding is in contradiction to the results reported by other researchers for a similar alloy composition.

Corrosion testing of type 304L stainless steel in tuff groundwater environments

International Nuclear Information System (INIS)

Westerman, R.E.; Pitman, S.G.; Haberman, J.H.

1987-11-01

The stress-corrosion cracking (SCC) resistance of Type 304L stainless steel (SS) to elevated temperatures in tuff rock and tuff groundwater environments was determined under irradiated and nonirradiated conditions using U-bend specimens and slow-strain-rate tests. The steel was tested both in the solution-annealed condition and after sensitization heat treatments. The material was found to be susceptible to SCC in both the solution-annealed and solution-annealed-and-sensitized conditions when exposed to an irradiated crushed tuff rock environment containing air and water vapor at 90 0 C. A similar exposure at 50 0 C did not result in failure after a 25-month test duration. Specimens of sensitized 304 SS conditioned with a variety of sensitization heat treatments resisted failure during a test of 1-year duration in which a nonirradiated environment of tuff rock and groundwater held at 200 0 C was allowed to boil to dryness on a cyclical basis. All specimens of sensitized 304 SS exposed to this environment failed. Slow-strain-rate studies were performed on 304L, 304, and 316L SS specimens. The 304L SS was tested in J-13 well water at 150 0 C, and the 316L SS at 95 0 C. Neither material showed evidence of SCC in these tests. Sensitized 304 SS did exhibit SCC in J-13 well water in tests conducted at 150 0 C. 12 refs., 27 figs., 13 tabs

Low temperature tensile deformation and acoustic emission signal characteristics of AISI 304LN stainless steel

Energy Technology Data Exchange (ETDEWEB)

Barat, K.; Bar, H.N. [Material Science and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Mandal, D. [Material Processing and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Roy, H., E-mail: himadri9504@gmail.com [NDT and Metallurgy Group, CSIR-Central Mechanical Engineering Research Institute, Durgapur 713209 (India); Sivaprasad, S.; Tarafder, S. [Material Science and Technology Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India)

2014-03-01

This investigation examines low temperature tensile deformation behavior of AISI 304LN stainless steel along with synergistic analysis of acoustic emission signals. The tensile tests are done at a range of temperatures starting from 283 K till 223 K. The fracture surfaces of the broken specimens are investigated using scanning electron microscope. The amount of deformation induced martensite is measured using a feritscope. The obtained results reveal that with decrease in test temperature, both strength and ductility increase. The increase in strength and ductility with decreasing temperature is explained in terms of void morphologies and formation of deformation induced martensite. The rapid increment in strength and ductility at 223 K is associated with the burst of martensitic transformation at that temperature; which has been clarified from acoustic emission signals. An additional initiative has been taken to model the evolution of martensite formation from the observed cumulative emission counts using a non linear logarithmic functional form. The fitted curves from the recorded acoustic emission cumulative count data are found to be better correlated compared to earlier obtained results. However, at 223 K normal non-linear logarithmic fit is not found suitable due to presence of burst type signals at intervals, therefore; piecewise logarithmic function to model acoustic emission bursts is proposed.

Microstructure and tribology of ion-mixed Fe/Ti/C multilayers on AISI 304 stainless steel

International Nuclear Information System (INIS)

Nastasi, M.; Hirvonen, J.P.; Zocco, T.G.; Jervis, T.R.

1991-01-01

A multilayered Fe/Ti/C structure consisting of eleven alternating sublayers, four Fe, four Ti and three C, was ion mixed on an AISI 304 stainless steel substrate with 400 keV Xe 2+ . Complete mixing was observed after an irradiation of 1x10 17 Xe/cm 2 at 550degC. Electron diffraction revealed the formation of the compounds TiC and Fe 3 C and a small amount of an amorphous phase. Some samples were given a second irradiation with 5x10 15 Xe/cm 2 at 0degC. The phases present following the second irradiation were TiC, α-Fe and an amorphous phase. Tribological and nanoindentation measurements revealed that both types of samples possessed similar hardness and friction properties. The ion mixed samples possessed an increased hardness and a decreased friction coefficient relative to untreated polished stainless-steel substrate. However, the wear life of the hot ion mixed sample was consistently longer than the wear life of the sample processed at both 550 and 0degC. These results are explained by differences in adhesive wear which result from differences in the chemical reactivity of the phases formed during ion beam processing. (orig.)

Modificación superficial de aceros y hierros fundidos mediante láser de Nd: YAG. // Steels and cast irons superficial modification by means of laser Nd: YAG.

Directory of Open Access Journals (Sweden)

R. Sagaró Z.

2001-10-01

Full Text Available Se presentan los resultados de los autores en el tratamiento térmico superficial con técnica láser (TTSL. Con el empleo deun láser de Nd: YAG se procedió al endurecimiento superficial de los aceros AISI 1045, W1, W112 y hierros fundidos detipo laminar y nodular. Los autores prestan atención a las rutas de endurecimiento superficial atendiendo a los parámetrosoperacionales del láser: potencia incidente en la zona de interacción (P y la velocidad de barrido del haz de láser (V. Deigual forma se establecen valoraciones acerca de las estructuras metalográficas obtenidas. En todos los casos se reportanvalores de microdureza Vickers que oscilan entre los 500-900 HV (incrementos de 3-4 veces respecto al substratooriginal. Los resultados obtenidos permiten establecer en todos los casos experimentados que el incremento de lavelocidad de barrido provocó una disminución de la profundidad de la capa endurecida. Las experiencias del TTSL en losaceros ensayados muestran una tendencia a la disminución de la profundidad del endurecimiento con el incremento delcontenido de carbono.Palabras claves: Endurecimiento superficial, parámetros de operación de láser., microdureza, profundidadde capa endurecida, de fallo, vibraciones.____________________________________________________________________________AbstractThis paper expose the experiences of researchers on the laser surface heat treatment. The hardening of AISI 1045, W1,W112 steels and cast irons flake and nodular was carried out by using a Nd: YAG laser. Operation parameters of laser, likebeam power (P and traverse speed of the laser spot (V are closely with hardening depth . Authors present some analysesabout metallographic studies. In all cases are reported Vickers microhardness about 500-900 HV (three or four times higherthan original substrates. Relations between microhardness and depth of hardening are presented for the processedmaterials. Experimental results showed that the increased

Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process

Energy Technology Data Exchange (ETDEWEB)

Wang, Haibo [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China); Song, Guolin [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Tang, Guoyi, E-mail: tanggy@mail.tsinghua.edu.cn [Advanced Materials Institute, Graduate School at Shenzhen, Tsinghua University, Shenzhen 518055 (China); Key Laboratory of Advanced Materials, Tsinghua University, Beijing 100084 (China)

2016-04-26

The present work integrates 3D digital optical microscopy (OM), nano-indentation, X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) to systematically investigate the effect of electropulsing on the surface mechanical properties and microstructure of AISI 304 stainless steel during the ultrasonic surface rolling process (USRP). Compared with the original USRP, the introduction of electropulsing with optimal parameters can effectively facilitate surface crack healing and improve surface hardness and wear resistance dramatically, and the residual compressive stress is further enhanced. Meanwhile, more martensite phase and fewer deformation twins can be found in the strengthened layer. Rapid improvement of the surface mechanical properties should be attributed to the ultra-refined grains, accelerated martensitic phase transformation and suppressed deformation twining induced by the coupling effect of USRP and electropulsing. The high strain rate given by USRP, increased stacking fault energy and accelerated dislocation mobility caused by electropulsing are likely the primary intrinsic reasons for the observed phenomena.

Decomposition kinetics of expanded austenite with high nitrogen contents

DEFF Research Database (Denmark)

Christiansen, Thomas; Somers, Marcel A. J.

2006-01-01

This paper addresses the decomposition kinetics of synthesized homogeneous expanded austenite formed by gaseous nitriding of stainless steel AISI 304L and AISI 316L with nitrogen contents up to 38 at.% nitrogen. Isochronal annealing experiments were carried out in both inert (N2) and reducing (H2......) atmospheres. Differential thermal analysis (DTA) and thermogravimetry were applied for identification of the decomposition reactions and X-ray diffraction analysis was applied for phase analysis. CrN precipitated upon annealing; the activation energies are 187 kJ/mol and 128 kJ/mol for AISI 316L and AISI 304L...

Superficial and electrochemical study of stainless steel 304l with an inhibitory protective coating (TiO{sub 2} and ZrO{sub 2}); Estudio superficial y electroquimico de acero inoxidable 304L con una capa protectora inhibidora (TiO{sub 2} y ZrO{sub 2})

Energy Technology Data Exchange (ETDEWEB)

Davila N, M. L.; Contreras R, A.; Arganis J, C. R., E-mail: aida.contreras@inin.gob.mx [ININ, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2014-10-15

The degradation mechanisms in the boiling water reactors (BWR) have been an alert focus for owners, especially the cracking by stress corrosion cracking (SCC), therefore different techniques have been studied to inhibit this problem inside which is the water injection of hydrogen feeding (HWC, Hydrogen Water Chemistry), together with the noble metals injection (NMCA, Nobel Metal Chemical Addition) and the ceramic materials injection that form an inhibitory protective coating (Ipc). In this work the Ipc was simulated, for which were carried out hydro-thermals deposits starting from suspensions of 1000 ppm of zirconium oxide in its crystalline phase baddeleyite and titanium oxides in its anatase and rutile phases, on test tubes of stainless steel 304l previously rusty under simulated conditions of pressure and temperature of a BWR (288 C and 8 MPa). The superficial characterization was realized by scanning electron microscopy, energy-dispersive of X-ray and X-ray diffraction. The capacity to mitigate the corrosion was studied with the electrochemical technique of Tafel polarization (288 C and 8 MPa). The steel presents the formation of two oxide coatings formed by magnetite and hematite. The baddeleyite presents a deposit more thick and homogeneous it also presents the most negative electrochemical potential of corrosion, what indicates that it has the bigger capacity to mitigate the SCC. (Author)

Ionic implantation by plasma in titanium and stainless steels used in prosthesis and medical instruments; Implantacion ionica por plasma en titanio y aceros inoxidables usados en protesis e instrumental medico

Energy Technology Data Exchange (ETDEWEB)

Munoz C, A. E. [ININ, 52750 La Marquesa, Estado de Mexico (Mexico)

2008-07-01

A study of a process known as plasma immersion ion implantation (PIII) of nitrogen at low voltages (< 4 kV) into three kind of samples: 1) austenitic stainless AISI 316-L steel plates, 2) ferritic stainless AISI 434 steel-based dentistry drills and 3) commercially pure titanium (CPTi) disks. On the case of CPTi the study was conducted in nitrogen- oxygen calibrated mixtures: 90% N-10% O, 80% N-20% O, 70% N-30% O and in 99.5% pure oxygen and 99.9% pure nitrogen. The PIII process was carried out by using a direct current plasma source controlled both in voltage and current, a negative voltage pulse modulator, a stainless AISI 304 steel vacuum chamber and a rod of the same material, horizontally located in the upper region of the chamber, which plays the role of anode in the plasma discharge. The purpose of the nitriding is forming a relatively thick layer on the surface of the steel specimens in order to enhance their both microhardness and general corrosion performances, desirable in medical applications. This layer contains interstitial nitrogen atoms ({approx}24% at.) which gives place to a deformed lattice (expanded phase) of the steel. Vickers microhardness and potentiodynamic tests (the latter in agreement to the norm ASTM G-61-89) confirm an increase of microhardness up to three times and a decrease of general corrosion rate in one order of magnitude. The nitriding of de dentistry drills is aimed at inhibiting the pitting corrosion produced by the asepsis process which results in pit nucleations, their propagation and consequent fractures when being under cyclic stress (fatigue). Scanning electron microscope micrographs reveal the risks involved in surpassing the critical treatment simple temperature of 450 C as the PIII process itself induces pitting. On its part, cyclic (ASTM G-61) potentiodynamic tests indicate an excellent pitting corrosion resistance of the samples treated under 450 C. In turn, the treatment of CPTi was meant to develop oxidized and

In pile AISI 316L. Low cycle fatigue. Final report

International Nuclear Information System (INIS)

Van Nieuwenhove, R.; Moons, F.

1994-12-01

In pile testing of the effect of neutron irradiation on the fatigue life of the reference material AISI 316L was performed in the framework of the European fusion technology program. The overall programme, carried out at SCK CEN (Mol,Belgium), exists of two instrumented rigs for low cycle fatigue testing, which were consecutively loaded in the BR-2 reactor during periods Jan (94) June (94) and Aug (94)-Dec(94). In each experiment, two identical samples were loaded by means of a pneumatically driven system. The samples were instrumented with thermocouples, strain gages, linear variable displacement transducers, and activation monitors. The experimental conditions are given. Type of fatigue test: load controlled, symmetric, uniaxial, triangular wave shape; stress range: about 580 MPa; sample shape: hourglass, diameter 3.2 mm, radius 12.5 mm; environment: NaK (peritectic); temperature: 250 C; maximum dpa value up to fracture: 1.7. Two of four samples were broken (one in each experiment) after having experienced 17 419 respectively 11 870 stress cycles. These new data points confirm earlier results from pile fatigue tests: irradiation causes no degradation of fatigue life of AISI 316L steel, at least for the parameters corresponding to these experiments

Stress Corrosion Cracking Susceptibility of 304L Substrate and 308L Weld Metal Exposed to a Salt Spray

Directory of Open Access Journals (Sweden)

Chia-Hao Hsu

2017-02-01

Full Text Available 304 stainless steels (SS were considered as the materials for a dry storage canister. In this study, ER (Electrode Rod 308L was utilized as the filler metal for the groove and overlay welds of a 304L stainless steel substrate, which was prepared via a gas tungsten arc-welding process in multiple passes. The electron backscatter diffraction (EBSD map was used to identify the inherent microstructures in distinct specimens. U-bend and weight-loss tests were conducted by testing the 304L substrates and welds in a salt spray containing 5 wt % NaCl at 80 °C to evaluate their susceptibility to stress corrosion cracking (SCC. Generally, the weight loss of the ER 308L deposit was higher than that of the 304L substrate in a salt spray in the same sample-prepared condition. The dissolution of the skeletal structure in the fusion zone (FZ was responsible for a greater weight loss of the 308L deposit, especially for the cold-rolled and sensitized specimen. Cold rolling was detrimental and sensitization after cold rolling was very harmful to the SCC resistance of the 304L substrate and 308L deposit. Overall, the SCC susceptibility of each specimen was correlated with its weight loss in each group.

Microchemical and microstructural evolution of AISI 304 stainless steel irradiated in EBR-II at PWR-relevant dpa rates

Energy Technology Data Exchange (ETDEWEB)

Dong, Y. [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States); Sencer, B.H. [Idaho National Laboratory, Idaho Falls, ID 83402 (United States); Garner, F.A. [Radiation Effects Consulting, Richland, WA 99354 (United States); Marquis, E.A., E-mail: emarq@umich.edu [Department of Materials Science and Engineering, University of Michigan, Ann Arbor, MI 48109 (United States)

2015-12-15

AISI 304 stainless steel was irradiated at 416 °C and 450 °C at a 4.4 × 10{sup −9} and 3.05 × 10{sup −7} dpa/s to ∼0.4 and ∼28 dpa, respectively, in the reflector of the EBR-II fast reactor. Both unirradiated and irradiated conditions were examined using standard and scanning transmission electron microscopy, energy dispersive spectroscopy, and atom probe tomography on very small specimens produced by focused ion beam milling. These results are compared with previous electron microscopy examination of 3 mm disks from essentially the same material. By comparing a very low dose specimen with a much higher dose specimen, both derived from a single reactor assembly, it has been demonstrated that the coupled microstructural and microchemical evolution of dislocation loops and other sinks begins very early, with elemental segregation producing at these sinks what appears to be measurable precursors to fully formed precipitates found at higher doses. The nature of these sinks and their possible precursors are examined in detail.

Microchemical and microstructural evolution of AISI 304 stainless steel irradiated in EBR-II at PWR-relevant dpa rates

Science.gov (United States)

Dong, Y.; Sencer, B. H.; Garner, F. A.; Marquis, E. A.

2015-12-01

AISI 304 stainless steel was irradiated at 416 °C and 450 °C at a 4.4 × 10-9 and 3.05 × 10-7 dpa/s to ∼0.4 and ∼28 dpa, respectively, in the reflector of the EBR-II fast reactor. Both unirradiated and irradiated conditions were examined using standard and scanning transmission electron microscopy, energy dispersive spectroscopy, and atom probe tomography on very small specimens produced by focused ion beam milling. These results are compared with previous electron microscopy examination of 3 mm disks from essentially the same material. By comparing a very low dose specimen with a much higher dose specimen, both derived from a single reactor assembly, it has been demonstrated that the coupled microstructural and microchemical evolution of dislocation loops and other sinks begins very early, with elemental segregation producing at these sinks what appears to be measurable precursors to fully formed precipitates found at higher doses. The nature of these sinks and their possible precursors are examined in detail.

Cavitation erosion resistance of AISI 316L stainless steel laser surface-modified with NiTi

International Nuclear Information System (INIS)

Chiu, K.Y.; Cheng, F.T.; Man, H.C.

2005-01-01

The present study is part of a project on the surface modification of AISI 316 stainless steel using various forms of NiTi for enhancing cavitation erosion resistance. In this study, NiTi powder was preplaced on the AISI 316L substrate and melted with a high-power CW Nd:YAG laser. With appropriate laser processing parameters, an alloyed layer of a few hundred micrometers thick was formed and fusion bonded to the substrate without the formation of a brittle interface. EDS analysis showed that the layer contained Fe as the major constituent element while the XRD patterns of the surface showed an austenitic structure, similar to that of 316 stainless steel. The cavitation erosion resistance of the modified layer (316-NiTi-Laser) could reach about 29 times that of AISI 316L stainless steel. The improvement could be attributed to a much higher surface hardness and elasticity as revealed by instrumented nanoindentation tests. Among various types of samples, the cavitation erosion resistance was ranked in descending order as: NiTi plate > 316-NiTi-Laser > 316-NiTi-TIG > AISI 316L, where 316-NiTi-TIG stands for samples surfaced with the tungsten inert gas (TIG) process using NiTi wire. Though the laser-surfaced samples and the TIG-surfaced samples had similar indentation properties, the former exhibited a higher erosion resistance mainly because of a more homogeneous alloyed layer with much less defects. In both the laser-surfaced and TIG-surfaced samples, the superelastic behavior typical of austenitic NiTi was only partially retained and the superior cavitation erosion resistance was thus still not fully attained

Analysis of correlations of multiple-performance characteristics for optimization of CO2 laser nitrogen cutting of AISI 304 stainless steel

Directory of Open Access Journals (Sweden)

Miloš Madić

2014-07-01

Full Text Available The identification of laser cutting conditions for satisfying different requirements such as improving cut quality characteristics and material removal rate is of great importance. In this paper, an attempt has been made to develop mathematical models in order to relate laser cutting parameters such as the laser power, cutting speed, assist gas pressure and focus position, and cut quality characteristics such as the surface roughness, kerf width and width of heat affected zone (HAZ. A laser cutting experiment was planned as per Taguchi’s L27 orthogonal array with three levels for each of laser cutting parameters considered. 3 mm thick AISI 304 stainless steel was used as workpiece material. Mathematical models were developed using a single hidden layer artificial neural network (ANN trained with the Levenberg– Marquardt algorithm. On the basis of the developed ANN models the effects of the laser cutting parameters on the cut quality characteristics were presented. It was observed that laser cutting parameters variously affect cut quality characteristics. Also, for the range of operating conditions considered in the experiment, laser cut quality operating diagrams were shown. From these operating diagrams one can see the values of cut quality characteristics that can be achieved and subsequently select laser cutting parameter values. Furthermore, the analysis includes correlations between cut quality characteristics and material removal rate. To this aim, six trade-off operating diagrams for improving multiple responses at the same time were given.

Experimental investigation on mechanical and microstructural properties of AISI 304 to Cu joints by CO2 laser

Directory of Open Access Journals (Sweden)

Bikash Ranjan Moharana

2016-06-01

Full Text Available Aim of the present work is to investigate mechanical and metallurgical characteristics of continuous wave CO2 laser welded dissimilar couple of AISI 304 stainless steel and commercially pure copper sheets in autogenous mode. Metallurgical analysis of the fusion zone has been done to understand the mixing and solidification behavior. Macroscopic examination has been carried out to observe the macro-segregation pattern of Cu, Fe and Cr rich phases in different zones, and the thickness of HAZ was found to be around 10 µm. The micro-channels formed from the steel side to weld pool describe that the copper solidifies first and provides the nucleation surface for the residual melt to grow. These tubular micro-channels formed may be due to carbide precipitation. The EDS analysis conforms the well mixing of SS and Cu inside the weld pool. The mechanical properties in terms of tensile stress found up to 201 MPa and the fracture are obtained outside the weld zone. Microhardness measurements over the fusion zone have been done to understand the keyhole growth and quenching, solidification sequence and stress distribution over the full area.

Study of carbonitriding thermochemical treatment by plasma screen in active with pressures main austenitic stainless steels AISI 409 and AISI 316L; Estudo do tratamento termoquimico de carbonitretacao por plasma em tela ativa com pressoes variaveis nos acos inoxidaveis austenitico AISI 316L e ferririco AISI 409

Energy Technology Data Exchange (ETDEWEB)

Melo, M.S.; Oliveira, A.M.; Leal, V.S.; Sousa, R.R.M. de; Alves Junior, C. [Centro Federal de Educacao Tecnologica do Maranhao (CEFET/MA), Sao Luis, MA (Brazil); Centro Federal de Educacao Tecnologica do Piaui (CEFET/PI), Teresina, PI (Brazil); Universidade Federal do Rio Grande do Norte (DF/UFRN), Natal, RN (Brazil). Dept. de Fisica. Labplasma

2010-07-01

The technique called Active Screen Plasma Nitriding (ASPN) is being used as an alternative once it offers several advantages with respect to conventional DC plasma. In this method, the plasma does not form directly in the sample's surface but on a screen, in such a way that undesired effects such as the edge effect is minimized. Stainless steels present not very satisfactory wearing characteristics. However, plasma carbonitriding has been used as to improve its resistance to wearing due to the formation of a fine surface layer with good properties. In this work, samples of stainless steel AISI 316L and AISI 409 were treated at pressures of 2.5 and 5 mbar. After the treatments they were characterized by microhardness, microscopy and Xray diffraction. Microscopy and hardness analysis showed satisfactory layers and toughness in those steels. (author)

Reactive sintering and microstructure development of tungsten carbide-AISI 304 stainless steel cemented carbides

Energy Technology Data Exchange (ETDEWEB)

Fernandes, C.M. [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); CEMUC-Mechanical Engineering Department, University of Coimbra, Rua Luís Reis Santos, Pinhal de Marrocos, 3030-788 Coimbra (Portugal); Oliveira, F.J. [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal); Senos, A.M.R., E-mail: anamor@ua.pt [Department of Materials and Ceramics Engineering, CICECO, University of Aveiro, 3810-193 Aveiro (Portugal)

2017-06-01

Sintering of WC-stainless steel (SS) composites within a typical binder range from 6 up to 15 wt% SS was investigated through constant heating rate dilatometry, in vacuum conditions, complemented by differential thermal analysis and by the study of the high temperature wetting behavior of SS on WC. The densification starts ∼900 °C with a typical densification curve for all compositions, where three distinct regions are discernible: the first one with a slow densification rate, followed by a second region where a sharp increase in the densification rate up to a maximum value dependent on the binder amount is observed and, finally, a third one with a slowdown of the densification rate until the end of the thermal cycle. The attained final density at 1450 °C is dependent on the binder amount, increasing proportionally to its initial content. The final microstructure presents a normal grain size distribution and appreciable amounts of eta-phase, besides the major WC phase and residual iron rich phase. The reactive densification behavior and the role of the liquid phase are interpreted accordingly with structural and kinetic data. - Highlights: • Sintering of WC-AISI304 composites starts ∼900 °C and involves three stages. • Densification is largely dominated by a reactive liquid phase sintering process. • Eta-phase constitutes a transient liquid phase during sintering. • Sintering cycles are dependent on the initial binder content.

Strain-induced phase transformation at the surface of an AISI-304 stainless steel irradiated to 4.4 dpa and deformed to 0.8% strain

Energy Technology Data Exchange (ETDEWEB)

Gussev, M.N., E-mail: gussevmn@ornl.gov; Field, K.G.; Busby, J.T.

2014-03-15

Surface relief due to localized deformation in a 4.4-dpa neutron-irradiated AISI 304 stainless steel was investigated using scanning electron microscopy coupled with electron backscattering diffraction and scanning transmission electron microscopy. It was found a body-centered-cubic (BCC) phase (deformation-induced martensite) had formed at the surface of the deformed specimen along the steps generated from dislocation channels. Martensitic hill-like formations with widths of ∼1 μm and depths of several microns were observed at channels with heights greater than ∼150 nm above the original surface. Martensite at dislocation channels was observed in grains along the [0 0 1]–[1 1 1] orientation but not in those along the [1 0 1] orientation.

Strain-induced phase transformation at the surface of an AISI-304 stainless steel irradiated to 4.4 dpa and deformed to 0.8% strain

International Nuclear Information System (INIS)

Gussev, M.N.; Field, K.G.; Busby, J.T.

2014-01-01

Surface relief due to localized deformation in a 4.4-dpa neutron-irradiated AISI 304 stainless steel was investigated using scanning electron microscopy coupled with electron backscattering diffraction and scanning transmission electron microscopy. It was found a body-centered-cubic (BCC) phase (deformation-induced martensite) had formed at the surface of the deformed specimen along the steps generated from dislocation channels. Martensitic hill-like formations with widths of ∼1 μm and depths of several microns were observed at channels with heights greater than ∼150 nm above the original surface. Martensite at dislocation channels was observed in grains along the [0 0 1]–[1 1 1] orientation but not in those along the [1 0 1] orientation

Time dependence of the natural passivation process on AISI 304 in an alkaline medium: Atomic force microscopy and scanning Kelvin probe force microscopy as additional tools to electrochemical impedance spectroscopy

Science.gov (United States)

Benaioun, N. E.; Maafa, I.; Florentin, A.; Denys, E.; Hakiki, N. E.; Moulayat, N.; Bubendorff, J. L.

2018-04-01

Thin surface films formed on AISI 304 samples in an alkaline solution of pH = 13 are studied by atomic force microscopy (AFM), scanning Kelvin probe force microscopy (SKPFM) and electrochemical impedance spectroscopy (EIS) as a function of immersion time. The results reveal that changes on EIS diagrams correspond to topographical modifications on the sample surface as shown by AFM. Both techniques are therefore complementary. The oxide layer is chemically homogenous as shown by SKPFM imaging and our ultra-thin passive layer is an efficient barrier against corrosion.

Effects of cold working on the pitting corrosion behavior s of AISI 304 stainless steels

Energy Technology Data Exchange (ETDEWEB)

Jung, Kee Min; Kim, Jong Soo; Kim, Young Jun; Kwon, Houk Sang [KAIST, Daejon (Korea, Republic of)

2015-12-15

These microstructural changes by cold working can lead improvement of mechanical properties, however from a corrosion resistant point of view, the effects of cold working on the corrosion resistance of stainless steel have been argued. Several studies has been focused on the influence of cold working on the localized corrosion resistance of stainless steels. However, the opinions about the role of cold working on the localized corrosion resistance are highly in consistence. Some studies report that the pitting potential of austenitic stainless steels decreased with cold working level, on the other hands, other studies claimed that the pitting resistance was increased by cold working. Therefore it is necessary to verify how cold working affects pitting corrosion behavior of austenitic stainless steels. In the present work, the influence of cold working on the localized corrosion of AISI 304stainless steel in the neutral chloride solution was studied based on point defect model (PDM). The fraction of deformation-induced martensite was linearly increased with cold rolling level. Through cold rolling, the pitting potential was decreased, the metastable pitting event density was significantly increased and the repassivation potential was decreased. The overall localized corrosion resistance was decreased with cold working, however cold working level increased from 30 % to 50 %, localized corrosion resistance was recovered. The accumulated cation vacancy generates a void at metal/film interface, therefore film breakdown accelerates for cold worked alloys.

Effects of cold working on the pitting corrosion behavior s of AISI 304 stainless steels

International Nuclear Information System (INIS)

Jung, Kee Min; Kim, Jong Soo; Kim, Young Jun; Kwon, Houk Sang

2015-01-01

These microstructural changes by cold working can lead improvement of mechanical properties, however from a corrosion resistant point of view, the effects of cold working on the corrosion resistance of stainless steel have been argued. Several studies has been focused on the influence of cold working on the localized corrosion resistance of stainless steels. However, the opinions about the role of cold working on the localized corrosion resistance are highly in consistence. Some studies report that the pitting potential of austenitic stainless steels decreased with cold working level, on the other hands, other studies claimed that the pitting resistance was increased by cold working. Therefore it is necessary to verify how cold working affects pitting corrosion behavior of austenitic stainless steels. In the present work, the influence of cold working on the localized corrosion of AISI 304stainless steel in the neutral chloride solution was studied based on point defect model (PDM). The fraction of deformation-induced martensite was linearly increased with cold rolling level. Through cold rolling, the pitting potential was decreased, the metastable pitting event density was significantly increased and the repassivation potential was decreased. The overall localized corrosion resistance was decreased with cold working, however cold working level increased from 30 % to 50 %, localized corrosion resistance was recovered. The accumulated cation vacancy generates a void at metal/film interface, therefore film breakdown accelerates for cold worked alloys

Effect of noble metals on the corrosion of AISI 316L stainless steel in nitric acid

International Nuclear Information System (INIS)

Robin, R.; Andreoletti, G.; Fauvet, P.; Terlain, A.

2004-01-01

In the spent fuel treatment, the solutions of fission products contain dissolution fines, in particular platinoids. These solutions are stored into AISI 316L stainless steel tanks, and the contact of noble metallic particles such as platinoids with austenitic stainless steels may induce a shift of the steel corrosion potential towards the trans-passive domain by galvanic coupling. In that case, the steel may be polarized up to a potential value above the range of passive domain, that induces an increase of the corrosion current. The galvanic corrosion of AISI 316L stainless steel in contact with different platinoids has been investigated by electrochemical and gravimetric techniques. Two types of tests were conducted in 1 mol/L nitric acid media at 80 deg C: (1) polarization curves and (2) immersion tests with either platinoid powders (Ru, Rh, Pd) or true insoluble dissolution fines (radioactive laboratory test). The results of the study have shown that even if galvanic coupling enhances the corrosion rate by about a factor 10 in these conditions, the corrosion behavior of AISI 316L remains low (a corrosion rate below 6 μm/year, few small intergranular indentations). No specific effect of irradiation and of elements contained in radioactive fines (other than Ru, Rh and Pd) was observed on corrosion behavior. A platinoids-ranking has also been established according to their coupling potential: Ru > Pd > Rh. (authors)

Mechanical and Microstructural Properties of Friction Welded AISI 304 Stainless Steel to AISI 1060 Steel AISI 1060

Directory of Open Access Journals (Sweden)

Ates H.

2014-10-01

Full Text Available Rotary Friction welding is one of the most popular methods of joining similar and dissimilar materials. It is widely used with metals and thermoplastics in a wide variety of aviation, transport and aerospace industrial component designs. This study investigates the influence of friction and upsetting pressures on the hardness, tensile properties and microstructure of the welds. The experimental results showed that as the friction and upsetting pressures increased, the hardness and tensile strength values increased, as well. The tensile fracture of welded joint occurred in the AISI 1060 side. The friction processed joints were evaluated for their integrity and quality aspects by optical and scanning electron microscopy. For the perfect interfacial bonding, sufficient upsetting and friction pressures are necessary to reach the optimal temperature and severe plastic deformation to bring these materials within the attraction range.

Efecto de las sales fundidas en la termofluencia del acero inoxidable tipo 304

Directory of Open Access Journals (Sweden)

González-Rodríguez, G.

1995-06-01

Full Text Available Problems caused by both hot corrosion and creep type-damage occurring on superheater and reheater tubes of power plants using heavy oil as fuel shorten their design lives. The acceleration of hot corrosion attack of boilers is caused by the presence of fuel ash deposits containing mainly vanadium, sodium and sulphur, in the form of Na₂SO₄ y V₂O₅ and V₂O₅ which form low melting point compounds. In addition to this, the tubes are exposed to the action of both high stresses and high temperatures, producing the so called creep damage. In this work, creep rupture tests were carried out in the temperature range of 620 to 660 °C in static air and in corrosive environments. The corrosive environments included 100 % Na₂SO₄, 100 % V₂O₅ and a 80 % V₂O₅ + 20 % Na₂SO₄ mixture.

Los problemas causados tanto por la corrosión por sales fundidas, así como por la termofluencia en los tubos de los sobrecalentadores y recalentadores de una planta de potencia que usa combustibles fósiles, reducen su vida prevista en diseño. La aceleración de la corrosión por sales fundidas es causada por la presencia de cenizas que contienen principalmente vanadio, sodio y azufre en la forma de Na₂SO₄ y V₂O₅, los cuales forman mezclas con eutécticos de bajo punto de fusión. Adicionalmente, los tubos están expuestos a la acción de altos esfuerzos y altas temperaturas, lo cual propicia la termofluencia del material. En este trabajo, se han realizado ensayos de termofluencia hasta la rotura en aire y en ambientes corrosivos en el rango de temperaturas de 620 a 660 °C. Los ambientes corrosivos fueron 100 % Na₂SO₄, 100 % V₂O₅, y una mezcla 20 % Na₂SO₄-80 % V₂O₅.

Statistical study by digitalized image analysis of pitting corrosion of an AISI 304 type stainless steel in chloride environment

International Nuclear Information System (INIS)

Lacome, Isabelle

1994-01-01

This research thesis addresses the pitting corrosion of an AISI 304-type stainless steel in chloride environment, a phenomenon which is generally considered as comprising two main steps: pit initiation with local degradation of the passive film, and pit growth. By using a technique of analysis of digitalized images, the process is observed in situ and both steps are monitored. A statistical study of the initiation of all the noticed pits is performed. After a bibliographical survey on the pitting corrosion process, its mechanisms and the influence of different parameters, the author presents the studied material and the experimental methods, reports the investigation of the pitting corrosion process in potentiostatic mode over a wide range of potentials in order to study all the types of pits, discusses the influence of potential on pit initiation and growth, reports the study of the influence of hydrodynamic conditions and of ageing in solution on the different parameters, reports the analysis of passive films by photoelectron spectroscopy, and the study of the influence of an inhibitor (molybdate ions) on both steps of pitting corrosion [fr

Dynamic compressive response of wrought and additive manufactured 304L stainless steels

Directory of Open Access Journals (Sweden)

Nishida Erik

2015-01-01

Full Text Available Additive manufacturing (AM technology has been developed to fabricate metal components that include complex prototype fabrication, small lot production, precision repair or feature addition, and tooling. However, the mechanical response of the AM materials is a concern to meet requirements for specific applications. Differences between AM materials as compared to wrought materials might be expected, due to possible differences in porosity (voids, grain size, and residual stress levels. When the AM materials are designed for impact applications, the dynamic mechanical properties in both compression and tension need to be fully characterized and understood for reliable designs. In this study, a 304L stainless steel was manufactured with AM technology. For comparison purposes, both the AM and wrought 304L stainless steels were dynamically characterized in compression Kolsky bar techniques. They dynamic compressive stress-strain curves were obtained and the strain rate effects were determined for both the AM and wrought 304L stainless steels. A comprehensive comparison of dynamic compressive response between the AM and wrought 304L stainless steels was performed. SAND2015-0993 C.

Simulación de la precipitación de inclusiones en diferentes etapas del procesamiento del acero líquido

Directory of Open Access Journals (Sweden)

Carreño, V.

1998-05-01

Full Text Available Steelmaking processes are continuously improved in order to attend the increasing requirements of the cleanness of the liquid metal. At the refining stages, as deoxidation and desulphuration, the formation of inclusions of oxides and sulphides is promoted, which on the other hand, are the most frequent inclusions. In this work a mathematical simulator of the precipitation and chemical composition of non-metallic inclusions at different steps of the steelmaking process is presented. To this purpose, it is assumed that inclusions formed by reoxidation can be simulated by increasing arbitrarily the oxygen levels consumed by the residual elements (aluminium, calcium, etc. and starting the chemical reaction with less powerful deoxidants (silicium and manganese. Accordingly, different operative conditions can be simulated. Numerical predictions are compared with experimental results of industrial trials, as well as results included in the bibliography.

Los procesos de fabricación de acero se mejoran constantemente en respuesta a las demandas del consumidor que exige un mayor control de limpieza del metal líquido en las diversas etapas de su elaboración. En las etapas de refinación, como son desoxidación y desulfuración, se promueve la formación de inclusiones de óxidos y sulfuros, que por otra parte son las más frecuentes en el acero líquido. En este trabajo se presenta un simulador matemático que predice la precipitación y composición de las inclusiones no metálicas que se encuentran en el acero líquido en diferentes etapas de su procesamiento, asumiendo que las inclusiones formadas por reoxidación también se pueden simular al incrementar arbitrariamente los niveles de oxígeno que deberán consumir los elementos residuales altamente oxidables (Al, Ca, y empezar la reacción con los desoxidantes menores (Si y Mn. De esta manera se simulan diferentes condiciones de operación. Las predicciones numéricas se comparan con los

High temperature oxidation behavior of AISI 304L stainless steel—Effect of surface working operations

International Nuclear Information System (INIS)

Ghosh, Swati; Kumar, M. Kiran; Kain, Vivekanand

2013-01-01

Highlights: ► Surface working resulted in thinner oxide on the surface. ► Oxides on machined/ground surfaces richer in Cr, higher in specific resistivity. ► Additional ionic transport process at the metal-oxide for ground sample established. ► Presence of fragmented grains and martensite influenced oxide nature/morphology. - Abstract: The oxidation behavior of grade 304L stainless steel (SS) subjected to different surface finishing (machining and grinding) operations was followed in situ by contact electric resistance (CER) and electrochemical impedance spectroscopy (EIS) measurements using controlled distance electrochemistry (CDE) technique in high purity water (conductivity −1 ) at 300 °C and 10 MPa in an autoclave connected to a recirculation loop system. The results highlight the distinct differences in the oxidation behavior of surface worked material as compared to solution annealed material in terms of specific resistivity and low frequency Warburg impedance. The resultant oxide layer was characterized for (a) elemental analyses by glow discharge optical emission spectroscopy (GDOES) and (b) morphology by scanning electron microscopy (SEM). Oxide layers with higher specific resistivity and chromium content were formed in case of machined and ground conditions. Presence of an additional ionic transport process has also been identified for the ground condition at the metal/oxide interface. These differences in electrochemical properties and distinct morphological features of the oxide layer as a result of surface working were attributed to the prevalence of heavily fragmented grain structure and presence of martensite.

Study of carbonitriding thermochemical treatment by plasma screen in active with pressures main austenitic stainless steels AISI 409 and AISI 316L

International Nuclear Information System (INIS)

Melo, M.S.; Oliveira, A.M.; Leal, V.S.; Sousa, R.R.M. de; Alves Junior, C.; Centro Federal de Educacao Tecnologica do Piaui; Universidade Federal do Rio Grande do Norte

2010-01-01

The technique called Active Screen Plasma Nitriding (ASPN) is being used as an alternative once it offers several advantages with respect to conventional DC plasma. In this method, the plasma does not form directly in the sample's surface but on a screen, in such a way that undesired effects such as the edge effect is minimized. Stainless steels present not very satisfactory wearing characteristics. However, plasma carbonitriding has been used as to improve its resistance to wearing due to the formation of a fine surface layer with good properties. In this work, samples of stainless steel AISI 316L and AISI 409 were treated at pressures of 2.5 and 5 mbar. After the treatments they were characterized by microhardness, microscopy and Xray diffraction. Microscopy and hardness analysis showed satisfactory layers and toughness in those steels. (author)

Estudio de la oxidación a elevada temperatura de ocho aleaciones en atmósferas de combustión de biomasa

Directory of Open Access Journals (Sweden)

Berlanga-Labari, C.

2008-08-01

resultados indican un buen comportamiento de los aceros inoxidables austeníticos y de las aleaciones de Inconel, mientras que el del acero martensítico no ha sido aceptable. Se ha propuesto el mecanismo conocido como “oxidación activa” para interpretar el comportamiento a la corrosión de estos materiales en estos medios.

Study of the solidification of M2 high speed steel Laser Cladding coatings

Directory of Open Access Journals (Sweden)

Candel, J. J.

2013-10-01

Full Text Available High speed steel laser cladding coatings are complex because cracks appear and the hardness is lower than expected. In this paper AISI M2 tool steel coatings on medium carbon AISI 1045 steel substrate have been manufactured and after Laser Cladding (LC processing it has been applied a tempering heat treatment to reduce the amount of retained austenite and to precipitate secondary carbides. The study of metallurgical transformations by Scanning Electron Microscopy (SEM and Electron Back Scattered Diffraction (EBSD shows that the microstructure is extremely fine and complex, with eutectic transformations and MC, M2C and M6C precipitation. Therefore, after the laser coating is necessary to use post-weld heat treatments.Los recubrimientos de acero rápido por Laser Cladding (LC son complejos porque aparecen fisuras y la dureza es menor a la esperada. En este trabajo se han fabricado recubrimientos de acero AISI M2 sobre acero al carbono AISI 1045 y tras el procesado por láser, se han revenido para reducir la cantidad de austenita retenida y precipitar carburos secundarios. El estudio de las transformaciones metalúrgicas con Microscopía Electrónica de Barrido (MEB y Difracción de Electrones Retrodispersados (EBSD muestra que la microestructura es extremadamente fina y compleja, presenta transformaciones eutécticas y precipitación de carburos MC, M2C y M6C. Por tanto, tras el recubrimiento por láser es necesario recurrir a tratamientos térmicos post-soldeo.

Cinéticas de transformación de fases a 850 ºC de aceros inoxidables dúplex clásicos (2205 y 2507 y de uno nuevo de bajo contenido en níquel y alto en manganeso (DBNi

Directory of Open Access Journals (Sweden)

Rodríguez, M. P.

2004-04-01

Full Text Available Austenitic-ferritic stainless steels are formed by ferrite and austenite in a variable proportion between 30 % and 70 %. Their chemical composition conditions the ageing processes that can happen during heat treatments, where phases that hardens and brittles the material can be generated. Evolution of a new duplex stainless steel with lower nickel and higher nitrogen and manganese content maintained at 1123 K (critical precipitation temperature up to 8 hours compared to classical ones (2205 and 2507 is presented. The study, done by magnetic measurements, XRD, optical and scanning electron microscopy and microanalysis, revealed a roughly similar behaviour for the three steels. The new one presents a higher initial stability, probably due to the high nitrogen and manganese contents; however, it also produces the higher final transformation due to the higher initial ferrite. A fine comparative analysis was done to correctly identify any phase; an accurate microanalysis in every generated phase was performed. All the steels tested are initially made on ferrite and austenite. After the ageing treatment, 8 hours at 1123 K, in the 2205 duplex steel a strong precipitation of sigma phase is observed, austenite and some of the original ferrite are also present; ferrite completely transforms in the 2507 duplex and austenite, sigma, secondary austenite and chromium nitride can be found; regarding the new duplex steel DBNi, austenite, ferrite, sigma, chi and chromium nitrides are detected.

Los aceros dúplex austeno-ferríticos están constituidos por ferrita y austenita en proporciones variables del 30 % al 70 %. Su composición química condiciona los procesos de envejecimiento que sufren durante los tratamientos térmicos, cuando se generan fases que endurecen y fragilizan el material. Este trabajo estudia la evolución de un nuevo inoxidable dúplex con bajo contenido en níquel y alto en nitrógeno y manganeso a 1123 K (temperatura crítica de

Electrochemical study of AISI 304 stainless steel during the exposure at the disinfectant solutions with fungal suspensions

Energy Technology Data Exchange (ETDEWEB)

Stoica, M.; Bruma, M. [Department of Biochemistry and Technologies, Faculty of Food Science and Engineering, ' ' Dunarea de Jos' ' University of Galati, 111 Domneasca Street, 800201 Galati (Romania); Carac, G. [Department of Chemistry, Faculty of Sciences, ' ' Dunarea de Jos' ' University of Galati, 47 Domneasca Street, 800008 Galati (Romania)

2010-12-15

The effect of fungal suspensions on the disinfectant solution (Actisept with sodium dichloroisocyanurate as active substance, which releases 140 ppm active chlorine) and the corrosion behavior of type AISI 304 stainless steel (SS) were evaluated through linear polarization. The work presents a study of biocide Actisept solution as reference solution and the mixed solutions: reference biocide Actisept solution with three fungal suspensions (10 vol%), Aspergillus niger, Candida mycoderma, and Saccharomyces cerevisiae. The fungal suspension has an important influence on the synergistic effect of the SS corrosion in the following order: Saccharomyces cerevisiae > Candida mycoderma > Aspergillus niger. The E{sub corr} values from the mixed solutions decreased with immersion time of the samples. In the case of Aspergillus niger, the corrosion rate was lower than that of any other type of fungal suspension tested, because the arrangement in solutions, the size and composition of Aspergillus niger spores were more favorable to protect the spores of the chemical and the electrical stressing. The results showed that there is a synergistic effect between the active substances from the disinfectant, fungal suspensions and applied potential, thus this effect can be taken into consideration for the hygienic and safety food industry. (Copyright copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Surface severe plastic deformation of AISI 304 via conventional shot peening, severe shot peening and repeening

Energy Technology Data Exchange (ETDEWEB)

Unal, Okan, E-mail: unalokan78@gmail.com [Mechanical Engineering Department, Bartın University, Bartın 74100 (Turkey); Varol, Remzi [Mechanical Engineering Department, Suleyman Demirel University, Isparta 32200 (Turkey)

2015-10-01

Highlights: • CSP and SSP treatments transform austenite to metastable martensite structure. • Nanograin layer thickness after CSP and SSP is 8 μm and 22 μm, respectively. • Shot peening leads to carbon segregation from coarse to nano grain layer. • Repeening is an effective way to reduce surface roughness. - Abstract: Air blast conventional shot peening (CSP), severe shot peening (SSP) and repeening (RP) as a severe plastic deformation applications on AISI 304 austenitic stainless steel is addressed. Shot peened specimens are investigated based on optical, FESEM and digital microscope. The investigations present the austenite transformation to metastable martensite via mechanical twinning due to plastic deformation with high strain rates. It is found that SSP induces thicker nanograin layer with compared to CSP. In XRD studies, the austenite peaks broaden by means of severe shot peening and FWHM increase reveals the grain size reduction below 25 nm regimes on the surface. In EDAX line analysis of CSP specimen, carbon content increase has been detected from deformed layer through the nanocrystalline layer then the content reduces. The carbon segregation takes place due to the energy level distinction between dislocations and Fe−C bonds. 3d contour digital microscope studies and roughness investigations reveal that SSP has deleterious side effect on the surface roughness and surface flatness. However, RP is an effective way to reduce the surface roughness to reasonable values.

Etude par diffraction des rayons X in situ des mécanismes d'oxydation de l'acier AISI 304 entre 800°C et 1000°C. Influence des dépôts sol-gel de lanthane et de cérium. Apport de la spectroscopie infrarouge à l'identification des oxydes mixtes

OpenAIRE

Karimi , Noureddine

2007-01-01

This work presents a study on the AISI 304 oxidation mechanism within the temperature range of 800 to 1000°C, in air. We have closely examined the effect of Lanthanum and Cerium sol-gel coating on the oxidation process. IR spectroscopy enables us to better identify the mixed oxides FeCr2O4 and Mn1,5Cr1,5O4 and the corundum type oxides Fe2O3 and Cr2O3. The combination of various analytical techniques such as: in situ XRD, IR spectroscopy, MEB, EDS and MET, lead us to propose a new oxidation me...

Oxidación en vapor de agua del acero inoxidable AISI 316 recubierto con Al-Si por deposición química de vapor en lecho fluidizado

Directory of Open Access Journals (Sweden)

José Luddey Marulanda Arevalo

2014-06-01

Full Text Available Stainless steel AISI 316 was coated with aluminum-silicon by Chemical Vapor Deposition in Fluidized Bed Reactor (CVD-FBR to 540°C and subsequently heat treated to improve its mechanical properties and its behavior against oxidation, by inter diffusion of the alloying elements. Later, oxidation was performed austenitic stainless steel aluminum-silicon coated at temperatures of 700 and 750°C, in an environment with 100% steam, to evaluate their performance. Mass gain graphs were made and oxide films were analyzed by SEM and X-ray diffraction to observe the morphology of the oxides. Thermodynamic simulation was carried out during oxidation in water vapor of the substrates for possible solid phases which could be formed. The form of attack at 750°C is similar to 700°C, although the rate of oxidation is increased, because the diffusion of the alloying elements and the oxidation reactions are faster. These coatings have good resistance to oxidation in water vapor and forming an alumina surface layer which protects the substrate from corrosion attack.

Surface characterization and wear behaviour of laser surface melted AISI 316L stainless steel

CSIR Research Space (South Africa)

Kumar, A

2010-01-01

Full Text Available The present study concerns an in depth investigation of the influence of laser surface melting of AISI 316L stainless steel using Ar and N2 as shrouding atmosphere. Laser surface melting has been carried out using a 5 kW continuous wave (CW) fibre...

Mechanical and tribological properties enhancement of heat treated AISI 4340 steel by using a TiN/TiAlN multilayer coating system

Directory of Open Access Journals (Sweden)

Gilberto Bejarano

2008-01-01

Full Text Available Multicapas de TiN/TiAlN (nitruro de titanio/nitruro de titanio aluminio se depositaron por la técnica de la pulverización catódica d.c. reactiva utilizando blancos de titanio y de aluminio de 10 cm de diámetro, con una pureza de 99,9%, en una atmósfera de argón y nitrógeno (Ar/N, aplicando una temperatura de 300°C y una presión de 7x10-3 mbar al sustrato. Como sustratos se utilizaron silicio (100 y acero AISI 4340 tratado térmicamente con una dureza de 54 Rockwell C (HRC, aproximadamente 5,4 GPa. Recubrimientos de TiN/TiAlN con un contenido de Al de 70% y un espesor total de 4 um se investigaron en función del número de multicapas y sus propiedades mecánicas y tribológicas se compararon con las de las muestras de acero sin recubrir. La estructura cristalina de las muestras recubiertas se analizó mediante difracción de rayos X, la morfología y topografía con microscopia electrónica de barrido (SEM y microscopia de fuerza atómica (AFM. La dureza se determinó mediante nanoindentación, mientras que la resistencia al desgaste se caracterizó a través de mediciones de pin on disc. Para las 150 multicapas de TiN/TiAlN se obtuvo un incremento en la dureza y en el módulo de Young de 62% y 70% respectivamente, en relación a las 30 bicapas iniciales, y de 740% y 202% respectivamente, comparado con el acero AISI 4340 sin recubrir. Finalmente, el coeficiente de fricción se redujo de 0,55 a 0,20 y la rugosidad de 60 nm a 3,2 nm para las probetas de acero recubiertas con 150 bicapas de TiN/TiAlN, lo cual condujo a una mayor resistencia al desgaste del sistema de recubrimiento.

Long-Term Effects of Temperature Exposure on SLM 304L Stainless Steel

Science.gov (United States)

Amine, Tarak; Kriewall, Caitlin S.; Newkirk, Joseph W.

2018-03-01

Austenitic stainless steel is extensively used in industries that operate at elevated temperatures. This work investigates the high-temperature microstructure stability as well as elevated-temperature properties of 304L stainless steel fabricated using the selective laser melting (SLM) process. Significant microstructural changes were seen after a 400°C aging process for as little as 25 h. This dramatic change in microstructure would not be expected based on the ferrite decomposition studied in conventional 304L materials. The as-built additively manufactured alloy has much faster kinetic response to heat treatment at 400°C. An investigation of the structures which occur, the kinetics of the various transformations, and the mechanical properties is presented. The impact of this on the application of SLM 304L is discussed.

L2 Milestone 5433: Characterization of Dynamic Behavior of AM and Conventionally Processed Stainless Steel (316L and 304L)

Energy Technology Data Exchange (ETDEWEB)

Gray, George Thompson [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Livescu, Veronica [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rigg, P. A. [Washington State Univ., Pullman, WA (United States). Inst. for Shock Physics; Trujillo, Carl Patrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Cady, Carl McElhinney [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Chen, Shuh-Rong [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carpenter, John S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Lienert, Thomas J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Fensin, Saryu Jindal [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Knapp, Cameron M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Beal, Roberta Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Morrow, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Dippo, Olivia F. [Univ. of California, San Diego, CA (United States); Jones, David Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Daniel Tito [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Valdez, James Anthony [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-26

For additive manufacturing (AM) of metallic materials, the certification and qualification paradigm needs to evolve as there currently exists no broadly accepted “ASTM- or DIN-type” additive manufacturing certified process or AM-material produced specifications. Accordingly, design, manufacture, and thereafter implementation and insertion of AM materials to meet engineering applications requires detailed quantification of the constitutive (strength and damage) properties of these evolving materials, across the spectrum of metallic AM methods, in comparison/contrast to conventionally-manufactured metals and alloys. This report summarizes the 316L SS research results and presents initial results of the follow-on study of 304L SS. For the AM-316L SS investigation, cylindrical samples of 316L SS were produced using a LENS MR-7 laser additive manufacturing system from Optomec (Albuquerque, NM) equipped with a 1kW Yb-fiber laser. The microstructure of the AM-316L SS was characterized in both the “as-built” Additively Manufactured state and following a heat-treatment designed to obtain full recrystallization to facilitate comparison with annealed wrought 316L SS. The dynamic shock-loading-induced damage evolution and failure response of all three 316L SS materials was quantified using flyer-plate impact driven spallation experiments at peak stresses of 4.5 and 6.35 GPa. The results of these studies are reported in detail in the first section of the report. Publication of the 316L SS results in an archival journal is planned. Following on from the 316L SS completed work, initial results on a study of AM 304L SS are in progress and presented herein. Preliminary results on the structure/dynamic spallation property behavior of AM-304L SS fabricated using both the directed-energy LENS and an EOS powder-bed AM techniques in comparison to wrought 304L SS is detailed in this Level 2 Milestone report.

Influence of the surface finishing on electrochemical corrosion characteristics of AISI 316L stainless steel

Czech Academy of Sciences Publication Activity Database

Dundeková, S.; Hadzima, B.; Fintová, Stanislava

2015-01-01

Roč. 22, č. 2 (2015), s. 77-84 ISSN 1335-0803 Institutional support: RVO:68081723 Keywords : AISI 316L stainless steel * EIS * Corrosion Subject RIV: JK - Corrosion ; Surface Treatment of Materials http://ojs.mateng.sk/index.php/Mateng/article/view/167/278

Cold rolled texture and microstructure in types 304 and 316L austenitic stainless steels

International Nuclear Information System (INIS)

Wasnik, D.N.; Samajdar, I.; Gopalakrishnan, I.K.; Yakhmi, J.V.; Kain, V.

2003-01-01

Two grades of austenitic stainless steel (ASS), types 304 (UNS S 30400) and 316L (UNS S 31603), were cold rolled to different reductions by unidirectional and by cross-rolling. The steels had reasonable difference in stacking fault energy (estimated respectively as 15 and 61 mJ/m 2 in types 304 and 316L) and also in starting (or pre-deformation) crystallographic texture-being relatively weak and reasonably strong in types 304 and 316L respectively. The cold rolling increased texturing in type 304, but not in type 316L ASS. The more significant effect of cold rolled texture development was in the relative increase of Brass ({011} ) against Copper ({112} ) and S ({231} ) orientations. In type 304 the increase in Brass was significant, while in type 316L the increase in Copper and S was stronger. This effect could be captured by Taylor type deformation texture simulations considering stronger twinning contributions in type 304 - for example the respective 'best-fits' (in terms of matching the changes in the volume fractions of Brass against Copper and S) were obtained by full constraint Taylor model with 1:100 and 1:10 slip:twin activities in types 304 and 316L ASS respectively. Microstructural developments during cold rolling were generalized as strain induced martensite formation and developments of dislocation substructure. The former, as estimated by vibrating sample magnetometer (VSM), increased with cold reduction, being significantly more in type 304 and was also noticeably stronger in both grades under cross-rolling. The most significant aspect of substructural developments was the formation of strain localizations. These were observed as dense dislocation walls (DDWs), micro-bands (MBs) and twin lamellar structures (TLS). The TLS contribution gained significance at higher reductions and during cross-rolling, especially in type 304. Large misorientation development and the accompanying grain splittings were always associated with such strain localizations

Mechanical and tribological properties of AISI 304 stainless steel nitrided by glow discharge compared to ion implantation and plasma immersion ion implantation

International Nuclear Information System (INIS)

Foerster, C.E.; Serbena, F.C.; Silva, S.L.R. da; Lepienski, C.M.; Siqueira, C.J. de M.; Ueda, M.

2007-01-01

Results about mechanical and tribological behavior of AISI 304 stainless steel nitrided by three different ion beam processes - glow discharge (GD), ion implantation (II) and plasma immersion ion implantation (PI3) are reported. Expanded austenite γ N and nitrides phases (Fe 2+x N, γ'-Fe 4 N and Cr-N) were identified as a function of nitriding conditions. Hardness (H) and elastic modulus (E) profiles were obtained by instrumented penetration. The hardness reached values as high as 21 GPa by PI3. Tribological behavior was studied by reciprocating sliding tests with a WC (Co) ball at room temperature (RT) in dry condition. Different wear regimes were identified in the friction coefficient profiles. The profile form and the running-in distance are strongly dependent on the nitriding process. Adhesive and abrasive wear components can be inferred from these friction profiles. Hardness and tribological performance, after the nitriding processes, are discussed in terms of surface microstructure

Evaluation of the mechanical properties of SA 333 Gr.6, AISI 304 and Zr-2.5% Nb through Automated Ball Indentation (ABI) technique

International Nuclear Information System (INIS)

Balakrishnan, K.S.; Rath, B.N.; Shriwastaw, R.S.; Ramadasan, E.; Kulkarni, R.V.; Sahoo, K.C.

2009-08-01

Automated Ball Indentation (ABI) technique has been employed in evaluating the tensile property data on three materials, namely SA333 Gr.6 carbon steel (used as PHT piping), AISI 304 (used as calandria vessel) and Zr-2.5% Nb (used as coolant tube) in Pressurised Heavy Water Reactors (PHWRs) with a view to exploring the applicability of ABI technique in providing reliable mechanical property data. The exercise was carried out in cooperation with a second laboratory where conventional tension tests alone were conducted such that the output of the study could be independently monitored and evaluated in an unbiased manner. The results generated in the authors' laboratory were found to be fully in agreement with what were obtained through conventional tension tests. Thus the study has been successful in establishing the reliability of the data obtained through miniature route especially in the case of coolant tube which has immense applications. (author)

Microstructural changes of AISI 316L due to structural sensitization and its influence on the fatigue properties

Directory of Open Access Journals (Sweden)

Sylvia Dundeková

2014-11-01

Full Text Available Mechanical and fatigue properties of material are dependent on its microstructure. The microstructure of AISI 316L stainless steel commonly used for the production of medical tools, equipment and implants can be easily influenced by its heat treatment. Microstructural changes and fatigue properties of AISI 316L stainless steel due to the heat treatment consisted of annealing at the temperature of 815°C with the dwell time of 500 hours were analyzed in the present paper. Precipitation of intermetallic phases and carbides was observed as a response of the material to the applied heat treatment. Small negative influence was observed in the case of fatigue region bellow 105 cycles; however the fatigue limit remains unchanged due to the structural sensitization.

Microstructural characterization of an AISI-SAE 4140 steel without nitridation and nitrided; Caracterizacion microestructural de un acero AISI-SAE 4140 sin nitrurar y nitrurado

Energy Technology Data Exchange (ETDEWEB)

Medina F, A.; Naquid G, C. [Gerencia de Ciencia de Materiales, Depto. de Sintesis y Caracterizacion de Materiales, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2000-07-01

It was micro structurally characterized an AISI-SAE 4140 steel before and after of nitridation through the nitridation process by plasma post-unloading microwaves through Optical microscopy (OM), Scanning electron microscopy (SEM) by means of secondary electrons and retrodispersed, X-ray diffraction (XRD), Energy dispersion spectra (EDS) and mapping of elements. (Author)

Influence of pre-deformation, sensitization and oxidation in high temperature water on corrosion resistance of AISI 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Lv, Jinlong, E-mail: ljltsinghua@126.com [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Liang, Tongxiang [Beijing Key Laboratory of Fine Ceramics, Institute of Nuclear and New Energy Technology, Tsinghua University, Zhongguancun Street, Haidian District, Beijing 100084 (China); State Key Lab of New Ceramic and Fine Processing, Tsinghua University, Beijing 100084 (China); Luo, Hongyun [Key Laboratory of Aerospace Materials and Performance (Ministry of Education), School of Materials Science and Engineering, Beijing University of Aeronautics and Astronautics, Xueyuan Road 37, Beijing 100191 (China)

2016-12-01

Highlights: • The pre-strain accelerated desensitization and sensitization for austenitic stainless steels. • Low temperature sensitization (carbide precipitation) induced α′-martensite. • The sensitization level could affect directly corrosion resistance of the oxide film. - Abstract: The effects of pre-deformation on sensitization of AISI 304 stainless steel were investigated by the double loop electrochemical potentiokinetic reactivation test. The effects of pre-deformation and sensitization on high temperature oxidized film formed in high temperature water were analyzed by a XRD and SEM. The electrochemical impedance spectroscopy at room temperature was used to study corrosion resistance of oxidized film. The point defect density of oxidized film was calculated by Mott–Schottky plots. The results showed that the value of the degree of sensitization first decreased and then slight increased with the increasing of engineering strain. Moreover, low temperature promoted to form sensitization induced “secondary” α′-martensite. The sample with 20% engineering strain had higher impedance value than other samples. The result was supported by further Mott–Schottky experiments. Considering increased α′-martensite with the increasing of strain, the results of the impedance were more consistent with values of the degree of sensitization.

Cold deformation effect on the microstructures and mechanical properties of AISI 301LN and 316L stainless steels

International Nuclear Information System (INIS)

Silva, Paulo Maria de O.; Abreu, Hamilton Ferreira G. de; Albuquerque, Victor Hugo C. de; Neto, Pedro de Lima; Tavares, Joao Manuel R.S.

2011-01-01

As austenitic stainless steels have an adequate combination of mechanical resistance, conformability and resistance to corrosion they are used in a wide variety of industries, such as the food, transport, nuclear and petrochemical industries. Among these austenitic steels, the AISI 301LN and 316L steels have attracted prominent attention due to their excellent mechanical resistance. In this paper a microstructural characterization of AISI 301LN and 316L steels was made using various techniques such as metallography, optical microscopy, scanning electronic microscopy and atomic force microscopy, in order to analyze the cold deformation effect. Also, the microstructural changes were correlated with the alterations of mechanical properties of the materials under study. One of the numerous uses of AISI 301LN and 316L steels is in the structure of wagons for metropolitan surface trains. For this type of application it is imperative to know their microstructural behavior when subjected to cold deformation and correlate it with their mechanical properties and resistance to corrosion. Microstructural analysis showed that cold deformation causes significant microstructural modifications in these steels, mainly hardening. This modification increases the mechanical resistance of the materials appropriately for their foreseen application. Nonetheless, the materials become susceptible to pitting corrosion.

Microstructural changes of AISI 316L due to structural sensitization and its influence on the fatigue properties

Czech Academy of Sciences Publication Activity Database

Dundeková, S.; Nový, F.; Fintová, Stanislava

2014-01-01

Roč. 21, č. 4 (2014), s. 172-177 ISSN 1335-0803 Institutional support: RVO:68081723 Keywords : AISI 316L * Structural sensitization * Rotating bending fatigue test Subject RIV: JL - Materials Fatigue, Friction Mechanics

Assessment and comparison of oxides grown on 304l ods steel and 304l ss in water environment in supercritical conditions

International Nuclear Information System (INIS)

Mihalache, M.; Dinu, A.; Fulger, M.; Zhou, Z.; Mihalache, M.

2013-01-01

In order to fulfil superior cladding for new reactor generation G IV, the austenitic 3 04 L stainless steel was improved by oxide dispersion strengthening (ODS), using two nano-oxides: titanium and yttrium oxides. The behaviour of the new material resulted, 304 ODS, in water at supercritical temperature of about 550 O C and 25 MPa pressure, was considered. The oxidation kinetics by weigh gain measurements for both materials have been estimated and compared. The weight gain of ODS samples is higher than basic austenitic steel up to 1320 hours. The oxides developed on the ODS samples in SCPW are layered and more uniform than in 304 L SS. The protectively character of oxide films was estimated by different techniques. The morphology of oxide surface, the layering and chemical formula of oxides films were investigated by scanning electron microscopy (SEM), Energy Dispersion X-Ray Spectrometry (EDS), electrochemical impedance spectrometry (EIS) and by Small Angle X-ray Diffraction (SAXD). 1. (authors)

Oxide layer stability in lead-bismuth at high temperature

Science.gov (United States)

Martín, F. J.; Soler, L.; Hernández, F.; Gómez-Briceño, D.

2004-11-01

Materials protection by 'in situ' oxidation has been studied in stagnant lead-bismuth, with different oxygen levels (H 2/H 2O ratios of 0.3 and 0.03), at temperatures from 535 °C to 600 °C and times from 100 to 3000 h. The materials tested were the martensitic steels F82Hmod, EM10 and T91 and the austenitic stainless steels, AISI 316L and AISI 304L. The results obtained point to the existence of an apparent threshold temperature above which corrosion occurs and the formation of a protective and stable oxide layer is not possible. This threshold temperature depends on material composition, oxygen concentration in the liquid lead-bismuth and time. The threshold temperature is higher for the austenitic steels, especially for the AISI 304L, and it increases with the oxygen concentration in the lead-bismuth. The oxide layer formed disappear with time and, after 3000 h all the materials, except AISI 304L, suffer corrosion, more severe for the martensitic steels and at the highest temperature tested.

Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

Science.gov (United States)

Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

2017-11-01

The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

Tensile Stress-Strain Results for 304L and 316L Stainless-Steel Plate at Temperature

International Nuclear Information System (INIS)

R. K. Blandford; D. K. Morton; S. D. Snow; T. E. Rahl

2007-01-01

The Idaho National Laboratory (INL) is conducting moderate strain rate (10 to 200 per second) research on stainless steel materials in support of the Department of Energy's (DOE) National Spent Nuclear Fuel Program (NSNFP). For this research, strain rate effects are characterized by comparison to quasi-static tensile test results. Considerable tensile testing has been conducted resulting in the generation of a large amount of basic material data expressed as engineering and true stress-strain curves. The purpose of this paper is to present the results of quasi-static tensile testing of 304/304L and 316/316L stainless steels in order to add to the existing data pool for these materials and make the data more readily available to other researchers, engineers, and interested parties. Standard tensile testing of round specimens in accordance with ASTM procedure A 370-03a were conducted on 304L and 316L stainless-steel plate materials at temperatures ranging from -20 F to 600 F. Two plate thicknesses, eight material heats, and both base and weld metal were tested. Material yield strength, Young's modulus, ultimate strength, ultimate strain, failure strength and failure strain were determined, engineering and true stress-strain curves to failure were developed, and comparisons to ASME Code minimums were made. The procedures used during testing and the typical results obtained are described in this paper

Martensitic transformation in 304L and 316L types stainless steels cathodically hydrogen charged

International Nuclear Information System (INIS)

Minkovitz, E.; Eliezer, D.

1984-01-01

This paper reports a TEM study on the role of phase transitions at the crack tip in 304L and 316L types stainless steels cathodically hydrogen charged in the absence of any eternally applied forces. The possible role of α prime and epsilon martensite phases in the fracture mechanism is discussed

Effect of Friction Coefficient on the Small Punch Creep Behavior of AISI 316L Stainless Steel

International Nuclear Information System (INIS)

Kim, Bum-Joon; Cho, Nam-Hyuck; Kim, Moon-K; Lim, Byeong-Soo

2011-01-01

Small punch creep testing has received attention due to the convenience of using smaller specimens than those of conventional uniaxial creep tests, which enables creep testing on developing or currently operational components. However, precedent studies have shown that it is necessary to consider friction between the punch and specimen when computing uniaxial equivalent stress from a finite element model. In this study, small punch creep behaviors of AISI 316L stainless steel, which is widely used in high temperature-high pressure machineries, have been compared for the two different ceramic balls such as Si 3 N 4 and Al 2 O 3 . The optimal range of the friction coefficient is 0.4⁓0.5 at 650°C for the best fit between experimental and simulation data of AISI 316 L stainless steel. The higher the friction coefficient, the longer the creep rupture time is. Therefore, the type of ceramic ball used must be specified for standardization of small punch creep testing.

Effect of heat input on the microstructure and mechanical properties of gas tungsten arc welded AISI 304 stainless steel joints

International Nuclear Information System (INIS)

Kumar, Subodh; Shahi, A.S.

2011-01-01

Highlights: → Welding procedure is established for welding 6 mm thick AISI 304 using GTAW process. → Mechanical properties of the weld joints are influenced strongly by the heat input. → Highest tensile strength of 657.32 MPa is achieved by joints using low heat input. → Welding parameters affect heat input and hence microstructure of weld joints. → Extent of grain coarsening in the HAZ increases with increase in the heat input. -- Abstract: Influence of heat input on the microstructure and mechanical properties of gas tungsten arc welded 304 stainless steel (SS) joints was studied. Three heat input combinations designated as low heat (2.563 kJ/mm), medium heat (2.784 kJ/mm) and high heat (3.017 kJ/mm) were selected from the operating window of the gas tungsten arc welding process (GTAW) and weld joints made using these combinations were subjected to microstructural evaluations and tensile testing so as to analyze the effect of thermal arc energy on the microstructure and mechanical properties of these joints. The results of this investigation indicate that the joints made using low heat input exhibited higher ultimate tensile strength (UTS) than those welded with medium and high heat input. Significant grain coarsening was observed in the heat affected zone (HAZ) of all the joints and it was found that the extent of grain coarsening in the heat affected zone increased with increase in the heat input. For the joints investigated in this study it was also found that average dendrite length and inter-dendritic spacing in the weld zone increases with increase in the heat input which is the main reason for the observable changes in the tensile properties of the weld joints welded with different arc energy inputs.

Microstructural evolution and precipitation behavior in heat affected zone of Inconel 625 and AISI 904L dissimilar welds

Science.gov (United States)

Senthur Prabu, S.; Devendranath Ramkumar, K.; Arivazhagan, N.

2017-11-01

In the present investigation an attempt has been made to join the dissimilar combination of Inconel 625 super alloy and super austenitic stainless steel (AISI 904L) using manual multi-pass continuous current gas tungsten arc (CCGTA) welding processes. Two different filler wires such as ERNiCrMo-4 and ERNiCrCoMo-1 have been used to compare the metallurgical properties of these welded joints. Both optical microscopy and scanning electron microscopy techniques were adopted to disseminate the microstructure traits of these weldments. Formation of secondary phases at the HAZ and weld interface of AISI 904L was witnessed while using the ERNiCrCoMo-1 filler, along with Solidification Grain Boundary (SGB) and Migrated Grain Boundary (MGB) were also observed at the weld zone.

Passivity and passivity breakdown of 304L stainless steel in hot and concentrated nitric acid

International Nuclear Information System (INIS)

Gillard-Tcharkhtchi, Elsa

2014-01-01

The objective of this study is to characterize the oxidation behavior of 304L stainless steel (SS) in representative conditions of spent nuclear fuel reprocessing, i.e. in hot and concentrated nitric acid. In these conditions the SS electrochemical potential is in the passive domain and its corrosion rate is low. However when the media becomes more aggressive, the potential may be shifted towards the trans-passive domain characterized with a high corrosion rate. Passivity and passivity breakdown in the trans-passive domain are of a major interest for the industry. So as to characterize these phenomenons, this work was undertaken with the following representative conditions: a 304L SS from an industrial sheet was studied, the media was hot and concentrated HNO 3 , long term tests were performed. First, the surface of an immersed 304L SS was characterized with several complementary techniques from the micro to the nanometer scale. Then oxidation kinetics was studied in the passive and in the trans-passive domain. The oxidation behavior was studied thanks to weight loss determination and surface analysis. Finally, oxidation evolution as a function of the potential was studied from the passive to the trans-passive domain. In particular, this allowed us to obtain the anodic curve of 304L SS in hot and concentrated and to define precisely the 304L SS limits of in such conditions. (author) [fr

Microstructural Evolutions During Reversion Annealing of Cold-Rolled AISI 316 Austenitic Stainless Steel

Science.gov (United States)

Naghizadeh, Meysam; Mirzadeh, Hamed

2018-06-01

Microstructural evolutions during reversion annealing of a plastically deformed AISI 316 stainless steel were investigated and three distinct stages were identified: the reversion of strain-induced martensite to austenite, the primary recrystallization of the retained austenite, and the grain growth process. It was found that the slow kinetics of recrystallization at lower annealing temperatures inhibit the formation of an equiaxed microstructure and might effectively impair the usefulness of this thermomechanical treatment for the objective of grain refinement. By comparing the behavior of AISI 316 and 304 alloys, it was found that the mentioned slow kinetics is related to the retardation effect of solute Mo in the former alloy. At high reversion annealing temperature, however, an equiaxed austenitic microstructure was achieved quickly in AISI 316 stainless steel due to the temperature dependency of retardation effect of molybdenum, which allowed the process of recrystallization to happen easily. Conclusively, this work can shed some light on the issues of this efficient grain refining approach for microstructural control of austenitic stainless steels.

Influence of the surface finishing on the corrosion behaviour of AISI 316L stainless steel

Czech Academy of Sciences Publication Activity Database

Dundeková, S.; Zatkalíková, V.; Fintová, Stanislava; Hadzima, B.; Škorík, Viktor

2015-01-01

Roč. 22, č. 1 (2015), s. 48-53 ISSN 1335-0803 R&D Projects: GA MŠk(CZ) EE2.3.30.0063 Institutional support: RVO:68081723 Keywords : AISI 316L stainless steel * Corrosion * Immersion test * Corrosion rate Subject RIV: JK - Corrosion ; Surface Treatment of Materials http://ojs.mateng.sk/index.php/Mateng/article/view/166/251

MICROSTRUCTURE AND FATIGUE PROPERTIES OF DISSIMILAR SPOT WELDED JOINTS OF AISI 304 AND AISI 1008

Directory of Open Access Journals (Sweden)

Nachimani Charde

2013-06-01

Full Text Available Carbon steel and stainless steel composites are being more frequently used for applications requiring a corrosion resistant and attractive exterior surface and a high strength structural substrate. Spot welding is a potentially useful and efficient jointing process for the production of components consisting of these two materials. The spot welding characteristics of weld joints between these two materials are discussed in this paper. The experiment was conducted on dissimilar weld joints using carbon steel and 304L (2B austenitic stainless steel by varying the welding currents and electrode pressing forces. Throughout the welding process; the electrical signals from the strain sensor, current transducer and terminal voltage clippers are measured in order to understand each and every millisecond of the welding process. In doing so, the dynamic resistances, heat distributions and forging forces are computed for various currents and force levels within the good welds’ regions. The other process controlling parameters, particularly the electrode tip and weld time, remained constant throughout the experiment. The weld growth was noted for the welding current increment, but in the electrode force increment it causes an adverse reaction to weld growth. Moreover, the effect of heat imbalance was clearly noted during the welding process due to the different electrical and chemical properties. The welded specimens finally underwent tensile, hardness and metallurgical testing to characterise the weld growth.

Notch Effect on Tensile Deformation Behavior of 304L and 316L Steels in Liquid Helium and Hydrogen

International Nuclear Information System (INIS)

Shibata, K.; Fujii, H.

2004-01-01

Tensile tests of type 304L and 316L steels were carried out using round bar specimens with a notch in liquid helium, hydrogen, liquid nitrogen and at ambient temperature. The obtained tensile strengths were compared with the tensile strengths of smooth specimens. For smooth specimens, tensile strength increased with a decrease in temperature and the strengths in liquid helium and hydrogen show similar values in both steels. For notched specimen of 304L steel, tensile strength (including fracture strength) increased noticeably from ambient to liquid nitrogen temperature but showed a large decrease in liquid helium and hydrogen. In liquid hydrogen and helium, the tensile strength is a little lower in liquid hydrogen than in liquid helium and both strengths are lower than tensile strengths of smooth specimens. For notched specimen of 316L steel, an increase in tensile strength from ambient to liquid nitrogen temperature was not so large and a decrease from liquid nitrogen to liquid hydrogen was small. The tensile strengths in liquid helium and hydrogen were nearly same and higher than those of smooth specimens. Different behavior of serration was observed between liquid helium and hydrogen, and between 304L and 316L steels. The reasons for these differences were discussed using computer simulation

Microstructure and mechanical properties of 304L steel fabricated by arc additive manufacturing

Directory of Open Access Journals (Sweden)

Ji Lei

2017-01-01

Full Text Available For 304L large structural parts used in nuclear power, it is hard and costly to fabricate and machine traditionally. Wire arc additive manufacturing (WAAM has low cost and high material utilization, which provides an efficient way to fabricate the large structural parts. So in this study, WAAM is used to fabricate the parts of 304L stainless steel. Through the tensile test and metallographic analysis, the mechanical properties and microstructure of the 304L stainless steel fabricated by WAAM were explored. The results indicate that with the layers depositing, the cooling rate becomes slower, the dendrites become thicker and the morphology becomes more stable. Due to the existence of dendrites, the grain boundary strengthening effect is different between the transverse direction and longitudinal direction, and resulting in anisotropy of mechanical properties. However, the mechanical properties of the parts correspond to the forged piece, which lays the foundation for future applications.

Influence of corrosion on the morphology and structure of ZrO{sub x}N{sub y}−ZrN coatings deposited on stainless steel

Energy Technology Data Exchange (ETDEWEB)

Cubillos, G.I., E-mail: gcubillos@unal.edu.co [Departamento de Química, Grupo de Materiales y Procesos Químicos, Universidad Nacional de Colombia, Bogotá (Colombia); Romero, E., E-mail: erromerom@unal.edu.co [Departamento de Química, Grupo de Materiales y Procesos Químicos, Universidad Nacional de Colombia, Bogotá (Colombia); Alfonso, J.E. [Grupo de Ciencia de Materiales y Superficies, Departamento de Física, Universidad Nacional de Colombia, AA 14490 Bogotá (Colombia)

2016-06-15

Morphological and structural changes of zirconium nitride and oxynitride thin films (ZrO{sub x}N{sub y}/ZrN) deposited via DC magnetron sputtering on stainless steel substrates (AISI 316L, 304LS, and 2205) in a reactive N{sub 2} and N{sub 2}/O{sub 2} atmosphere mixed with argon were studied. The crystallographic structures of the films were established through X-ray diffraction (XRD). The morphology was evaluated via scanning electron microscopy (SEM) and atomic force microscopy (AFM), and the corrosion resistance was evaluated using electrochemical techniques based on linear polarization (PL). The XRD analysis showed that the films were composed of cubic ZrO{sub x}N{sub y} and monoclinic ZrO{sub 2}. The electrochemical test showed that there was corrosion because of pitting phenomena and delamination in the coating deposited on AISI 2205 and AISI 304LS substrates. For AISI 316L, the damage generated by the corrosive solution was less. On the various substrates, an increase in the films' roughness was observed after the corrosion test. - Highlights: • We study the crystallographic change of ZrOxNy thin films after corrosion. • It was evaluated the morphological change of the coating after corrosion in NaCl solution. • The ZrOxNy films grew in the cubic phase and preferentially oriented along the (222) plane. • For AISI 316L, the damage generated by the corrosive solution was less, compared with AISI 304LS and AISI 2205.

AISI 304 ÖSTENİTİK PASLANMAZ ÇELİKLERİN TİTANYUM KARBÜR KAPLAMALI KESİCİ TAKIM İLE TORNALAMA İŞLEMİNDE KESME KUVVETLERİNİN İNCELENMESİ

Directory of Open Access Journals (Sweden)

Özgür TEKASLAN

2007-02-01

Full Text Available Bu araştırmada, AISI 304 östenitik paslanmaz çeliklerin titaniyum karbür kaplı kesici takımlarla tornalama işleminde oluşan kesme kuvvetleri deneysel olarak incelenmiş ve elde edilen sonuçlar teorik sonuçlarla karşılaştırılmıştır. Deneysel çalışmada, farklı kesme hızları, ilerleme değerleri ve kesme derinlikleri dikkate alınmıştır. Kesme kuvvetleri üç boyutlu kistler dinanometre ile ölçülmüştür. Teorik çalışmada ise; Kienzle formülasyonuna göre kesme kuvvetleri belirlenmiştir. Çalışma sonucunda teorik olarak hesaplanan kesme kuvvetlerinin çeşitli etkenler nedeni ile tam sonucu vermediği, deneysel sonuçlara göre; ortalama % 25'lik fark olduğu tespit edilmiştir. Bu nedenle kesme kuvvetlerinin belirlenmesinde deneysel yöntemin daha kesin sonuçlar verdiği değerlendirilmektedir.

Improvement in cavitation erosion resistance of AISI 316L stainless steel by friction stir processing

Energy Technology Data Exchange (ETDEWEB)

Hajian, M. [Department of Materials Engineering, Tarbiat Modares University, P.O. Box 14115-143, Tehran (Iran, Islamic Republic of); Abdollah-zadeh, A., E-mail: zadeh@modares.ac.ir [Department of Materials Engineering, Tarbiat Modares University, P.O. Box 14115-143, Tehran (Iran, Islamic Republic of); Rezaei-Nejad, S.S.; Assadi, H. [Department of Materials Engineering, Tarbiat Modares University, P.O. Box 14115-143, Tehran (Iran, Islamic Republic of); Hadavi, S.M.M. [Department of Materials Science and Engineering, MA University of Technology, Tehran (Iran, Islamic Republic of); Chung, K. [Department of Materials Science and Engineering, Research Institute of Advanced Materials, Engineering Research Institute, Seoul National University, Seoul (Korea, Republic of); Shokouhimehr, M. [Department of Chemical Engineering, College of Engineering, Seoul National University, Seoul 151-742 (Korea, Republic of)

2014-07-01

Commercial AISI 316L plates with the initial grain size of 14.8 μm were friction stir processed (FSP) with different processing parameters, resulting in two fine-grained microstructures with the grain sizes of 4.6 and 1.7 μm. The cavitation erosion behavior, before and after FSP, was evaluated in terms of incubation time, cumulative mass loss and mean depth of erosion. A separate cavitation erosion test was performed on the transverse cross section of a FSP sample to reveal the effect of grain structure. It was observed that FSP samples, depending on their grain size, are at least 3–6 times more resistant than the base material against cavitation erosion. The improvement in cavitation erosion resistance is attributed to smaller grain structure, lower fraction of twin boundaries, and favorable crystallographic orientation of grains in FSP samples. The finer the grain size, the more cavitation erosion resistance was achieved. Moreover, the microstructures of eroded surfaces were studied using a scanning electron microscope equipped with EBSD, and an atomic force microscope. The mechanisms controlling the cavitation erosion damage in friction stir processed AISI 316L are also discussed.

Characterization of metallurgical and mechanical properties on the multi-pass welding of Inconel 625 and AISI 316L

Energy Technology Data Exchange (ETDEWEB)

Kumar, K. Gokul; Ramkumar, K. Devendranath; Arivazhagan, N. [VIT University, Vellore (India)

2015-03-15

This article investigated the weldability, metallurgical and mechanical properties of Inconel 625 and AISI 316L stainless steel weldments obtained by continuous current (CC) and pulsed current (PC) gas tungsten arc welding (GTAW) processes employing ERNiCr-3 and ER2209 fillers. Microstructure studies showed the migrated grain boundaries at the weld zone of ERNiCr-3 weldments and multidirectional grain growth for ER2209 weldments. It was inferred from the tension tests that the fracture occurred at the parent metal of AISI 316L in all the cases. Charpy V-notch impact tests accentuated that the CCGTA weldments employing ERNiCr-3 filler offered better impact toughness of 77 J at room temperature. Further a detailed study has been carried out to analyze the structure - property relationships of these weldments using the combined techniques of scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis.

Effect of sensitization on the mechanical properties of type 304 L stainless steel

International Nuclear Information System (INIS)

Vargas Mendoza, L.F.

1990-01-01

The sensitization is a corrosion cause that it has studied broadly in the austenitic steels; however its relations don't knowed very well, into the sensitization and the steel's mechanical properties. Wherefore, the objectives of this work was to study the mechanical properties, in tension of austenitic steel with different levels of sensitization. The material utilized was a 304 L steel of standard composition AISI. The samples were sensitized at 450, 650 and 850 Centigrade degree, by short expositions, following by a temper in water. After this treatment, the tension test tubes were carried to rupture at low deformation velocity. The sensitization was evaluated by the method of Akashi EPR cyclic polarization. The sensitization distribution was analyzed by optical metallography in color and the fracture surface were studied by sweeping electronic microscopy. The distribution and length of the carbides were the factor that control the mechanic behavior of materials. At 450 Centigrade, the border of the grain its founded free of carbides, also for the longest times of exposition, but the particles are presented as fine precipitates in the grain interior, with this is increased the mechanical properties by the internal interactions of hardness or oldness types. At 650 Centigrade the frontiers show a dense distribution of fine carbides. These precipitates are interacting with the borders grain, increasing lightly the mechanical properties of steel. At 850 Centigrade, were formed discontinued carbides that not affect the mechanical behavior, but whether the fracture; the resistance is reduced and the ductility is increased although to impose the thermic effect of treatment. (Author)

Pulse generator for bias materials in the plasma immerse ion implantation process; Generador de pulsos para polarizar materiales en el proceso de implantacion de iones inmersos en plasma

Energy Technology Data Exchange (ETDEWEB)

Lopez Callegas, Regulo; Valencia Alvarado, Raul; Munoz Castro, Arturo Eduardo; Godoy Cabrera, Oscar Gerardo [Instituto Nacional de Investigaciones Nucleares, Mexico D.F. (Mexico); Moreno Saavedra, Hilda; Gonzalez Colin, Mireya; Mariano Escamilla, Hector Fernando [Instituto Tecnologico de Toluca, Estado de Mexico (Mexico)

2003-10-15

The 0-10 kV pulse generator has been designed, with 100 {mu}s duration and 1-100 Hz frequencies ranges. The use of the pulse generator is in the plasma immersed ion implantation technique (P III). The process was realized in 304 austenitic stainless steel, the results were analyzed by: SEM, X-rays diffraction and hardness Vickers. The hardness was increased due to the efficiency of the pulse generator and P III process, the results obtained showed that the nitrogen inside the stainless steel was implanted and besides some nitrides was formed and therefore the hardness was increased. Also, the more adequate work pressure was determined to carry out the P III process. [Spanish] Se presenta el diseno de un generador de pulsos de alto voltaje con amplitudes controladas de hasta 10 kV, la duracion maxima de los pulsos es del orden de los 100 {mu}s y frecuencia de repeticion en el intervalo de 1-100 Hz. La aplicacion de este generador de pulsos es para el proceso de implantacion de iones en materiales inmersos en plasmas (PIII). Los analisis hechos a los aceros austeniticos cedula 304 mediante microscopia electronica de barrido, difraccion de rayos X y dureza Vickers, muestran la eficiencia obtenida con el generador de pulsos en el proceso PIII, debido a que en el acero inoxidable se presenta un incremento en el nitrogeno y conformacion de algunos nitruros, lo cual da lugar al incremento de la dureza. Asimismo, se determino la presion de trabajo mas adecuada para llevar a cabo el proceso PIII.

Treatment of nitridation by microwave post discharge plasma in an AISI 4140 steel; Tratamiento de nitruracion por plasma post-descarga micro-ondas en un acero AISI 4140

Energy Technology Data Exchange (ETDEWEB)

Medina F, A. [Instituto Tecnologico de Morelia, Morelia e Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico); Rodriguez L, V.; Zamora R, L. [ININ, Mexico D.F. (Mexico); Oseguera P, J

1998-07-01

The objective of this work is to determine through X-ray diffraction, microhardness measurement and scanning electron microscopy those main operation parameters of the microwave post discharge treatment (temperature of treatment, gas mixture and permanence time) nitriding an AISI 4140 steel and to characterize the compact layer of nitrides formed during the treatment. (Author)

Effects of strain and strain-induced α′-martensite on passive films in AISI 304 austenitic stainless steel

International Nuclear Information System (INIS)

Lv, Jinlong; Luo, Hongyun

2014-01-01

In this paper, the effects of strain and heat treatment on strain-induced α′-martensite of AISI 304 stainless steel tubes were measured by X-ray diffraction. Moreover, the effects of strain and content of α′-martensite on passivated property on the surface of the material in borate buffer solution were evaluated by electrochemical technique. The results showed that the volume fraction of α′-martensite increased gradually with the increase of tensile strain for as-received and solid solution samples. However, α′-martensite in as-received sample was more than that in the solid solution sample. The electrochemical impedance spectroscopy results showed that the solid solution treatment improved corrosion resistance of the steel, especially for samples with small strain. Moreover, acceptor densities were always higher than donor densities for as-received and solid solution samples. With the increase of strain, the increase tendency of acceptor density was more significant than that of donor density. We also found that the total density of the acceptor and donor almost increased linearly with the increase of α′-martensite. The present results indicated that the increased acceptor density might lead to the decreased corrosion resistance of the steel. - Highlights: • The solid solution treatment improved corrosion resistance of the stainless steel. • The deteriorated passivated property after strain could be attributed to the increased acceptor density. • The α′-martensite reduced corrosion resistance of the stainless steel

Analysis of surface integrity in machining of AISI 304 stainless steel under various cooling and cutting conditions

Science.gov (United States)

Klocke, F.; Döbbeler, B.; Lung, S.; Seelbach, T.; Jawahir, I. S.

2018-05-01

Recent studies have shown that machining under specific cooling and cutting conditions can be used to induce a nanocrystalline surface layer in the workspiece. This layer has beneficial properties, such as improved fatigue strength, wear resistance and tribological behavior. In machining, a promising approach for achieving grain refinement in the surface layer is the application of cryogenic cooling. The aim is to use the last step of the machining operation to induce the desired surface quality to save time-consuming and expensive post machining surface treatments. The material used in this study was AISI 304 stainless steel. This austenitic steel suffers from low yield strength that limits its technological applications. In this paper, liquid nitrogen (LN2) as cryogenic coolant, as well as minimum quantity lubrication (MQL), was applied and investigated. As a reference, conventional flood cooling was examined. Besides the cooling conditions, the feed rate was varied in four steps. A large rounded cutting edge radius and finishing cutting parameters were chosen to increase the mechanical load on the machined surface. The surface integrity was evaluated at both, the microstructural and the topographical levels. After turning experiments, a detailed analysis of the microstructure was carried out including the imaging of the surface layer and hardness measurements at varying depths within the machined layer. Along with microstructural investigations, different topological aspects, e.g., the surface roughness, were analyzed. It was shown that the resulting microstructure strongly depends on the cooling condition. This study also shows that it was possible to increase the micro hardness in the top surface layer significantly.

Microstructure and corrosion resistance of nitrogen-rich surface layers on AISI 304 stainless steel by rapid nitriding in a hollow cathode discharge

Science.gov (United States)

Li, Yang; He, Yongyong; Zhang, Shangzhou; Wang, Wei; Zhu, Yijie

2018-01-01

Nitriding treatments have been successfully applied to austenitic stainless steels to improve their hardness and tribological properties. However, at temperatures above 450 °C, conventional plasma nitriding processes decrease the corrosion resistance due to the formation of CrN phases within the modified layer. In this work, AISI 304 austenitic stainless steels were efficiently treated by rapid plasma nitriding at a high temperature of 530 °C in a hollow cathode discharge. The enhanced ionization obtained in the hollow cathode configuration provided a high current density and, consequently, a high temperature could be attained in a short time. The nitrided layers were characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and X-ray photoelectron spectroscopy. The results indicated that the dual-layer structure of the nitrided layer consists of a high-N face-centered cubic structure with a free CrN precipitate outer (top) layer and a nitrogen-expanded austenite S-phase bottom layer. The rapid nitriding-assisted hollow cathode discharge technique permits the use of high temperatures, as high as 530 °C, without promoting degradation in the corrosion resistance of stainless steel.

Inorganic inhibitor study in the steel corrosion in the mixture of LiBr+Etilenglicol+H{sub 2}O; Estudio de inhibidores inorganicos en la corrosion de aceros en la mezcla de LiBr+Etilenglicol+H{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Sarmiento Bustos, Estela

2008-07-15

develop this work. Fourth chapter is the results presentation and discussion divided in four sections: each one for material electrochemically tested in the LiBr+ etilene glycol+ H{sub 2}O solution. Also presents the results obtained for the extended study made to carbon steel under different temperature and electrochemical test conditions. This includes the EIS and electrochemical noise Hurst results analysis and simulations. Finally, the fifth chapter presents the conclusions and recommendations of this work. An appendix with the solution preparation is included. [Spanish] En esta tesis doctoral se presentan los resultados obtenidos de cinetica electroquimica de la corrosion de 4 aceros: acero al carbon, 304, 316 y 316L, en una solucion de LiBr+ etilenglicol+H{sub 2}O. Estos sistemas son utilizados en bombas de calor por absorcion para la recuperacion de calor de desecho a la salida de procesos industriales. Sin embargo, la solucion absorbente es altamente corrosiva en este tipo de equipos. Por lo anterior se evaluaron tres diferentes inhibidores inorganicos: nitrato de litio, molibdato de litio y cromato de litio los cuales son fuertes oxidantes y promueven la formacion de la capa pasiva de los aceros y se aplicaron a diferentes temperaturas: 25, 50 y 80 grados dentigrados. A traves de tecnicas electroquimicas como curvas de polarizacion, ruido electroquimico, impedancia electroquimica, resistencia a la polarizacion lineal y mediciones de potencial de corrosion a circuito abierto en el tiempo. Se determino el compuesto inhibidor mas adecuado obteniendo su eficiencia bajo las diferentes condiciones, de los tres inhibidores considerados el que presento el mejor comportamiento y eficiencia para el acero al carbon fue el nitrato de litio a 50 ppm; para el 304 el cromato de litio a 5 ppm; para el acero 316 molibdato de litio a 5 ppm y para el 316L el cromato de litio a 5 ppm. Debido a que el acero al carbon es el material mas economico y presento una mejor respuesta por

Study of cyclic oxidation for stainless steels AISI 309 T 253 M A, with low additions of cerium; Estudio de la oxidacion ciclica de los aceros inoxidables AISI 309 T 253 MA, con pequenas adiciones de Cerio

Energy Technology Data Exchange (ETDEWEB)

Velazquez F, G.L.; Martinez, M.; Ruiz, A. [Universidad Nacional Experimental Politecnica (UNEXPO) - Vicerrectorado de Puerto Ordaz, Centro de Estudios de Corrosion. Puerto Ordaz. venezuela (Venezuela)

1998-12-31

It has been detected that the addition of small amounts (<1%) of the so called `reactive elements` such as Cerium to Fe-Cr alloys that was utilized in oxidating environment at high temperatures improving its resistance to oxidation under isothermal and cyclic conditions. In this work, it was evaluated the behavior under cyclic oxidation conditions for an austenitic stainless steel at chromium-nickel (253MA) with cerium addition, and comparing it with the AISI 310S austenitic stainless steel. The cyclic oxidation essays consist of five cycles by 24 hours each one, following of a cooling in air until ambient temperature from the temperatures of 850, 900 and 950 Centigrade, registering the gain mass of the specimen at end of each cycle. In order to this were prepared samples with dimensions of 20 mm. x 10 mm. x 1 mm. Later to the oxidation essays was evaluated the morphology of the corrosion products layer by scanning electron microscopy. The present phases were identified by X-ray diffraction and by chemical microanalysis by Dispersive energy (EDAX). The results obtained show that the steel with cerium addition, presents a higher adherence and resistance to the spalling noting that the cerium promotes the casting anchor of the oxides layer to matrix and by reducing the grain size of the layer improving its plasticity. Additionally the cerium promotes the preferential oxidation of the forming elements of protective layers like the chromium. (Author)

Electropolishing of AISI-304 stainless steel using an oxidizing solution originally used for electrochemical coloration

International Nuclear Information System (INIS)

Andrade, Leonardo S.; Xavier, Sandro C.; Rocha-Filho, Romeu C.; Bocchi, Nerilso; Biaggio, Sonia R.

2005-01-01

Chemical polishing or electropolishing, instead of mechanical polishing, are recommended for the attainment of metallic surface polishes without the introduction of contaminants or tensions in the surface layers of the metal. The fundamental difference between the chemical and electrochemical polishing processes is that in the latter anodic currents/potentials are used to help in the dissolution and passivation of the metal. In this paper, the use of an oxidizing electrolytic solution (2.5 mol L -1 CrO 3 + 5.0 mol L -1 H 2 SO 4 ) originally employed in electrochemical coloration processes is reported for the electropolishing of AISI-314 stainless steel. Parameters involved in this electropolishing process, such as temperature, current density and time, were optimized so as to attain the best possible results evaluated by the obtained surface brightness measured by reflectance spectra. Surface analyses by scanning electron microscopy allowed a clear correlation between obtained brightness and surface smoothing. The best conditions obtained for the electropolishing process are: temperature of 45 deg. C, electrolysis time of 10 min and current density of around 25 A dm -2 . It should be pointed out that an electropolishing process signature (periodic oscillations of the cell potential) was established; this may be an important tool for optimizing and monitoring electropolishing processes

Relationship between mechanical and surface properties of a stainless steels duplex UNS S31803 (45N) nitriding at high temperature

OpenAIRE

Mesa Grajales, Dairo Hernán; Garzón Ospina, Carlos Mario; Tschiptschin, André Paulo

2008-01-01

Se estudió la relación entre dureza, resistencia a la cavitación (en sus primeras etapas), y la textura cristalográfica de un acero inoxidable duplex (UNS S31803 llamado de 45N), transformado en inoxidable austenítico por tratamiento térmoquímico de nitruración gaseosa a alta temperatura. Usando la técnica de difracción de electrones retroproyectados (Electron Backscattering Diffraction - EBSD), fue posible generar un patrón de textura del material (mapa EBSD), el cual se utilizó pa...

Evaluación del comportamiento mecánico y superficial de materiales metálicos sometidos a tratamientos de compresión mediante ondas de choque generadas por láser

OpenAIRE

Gutiérrez González, Javier

2016-01-01

El presente trabajo de fin de grado se ha desarrollado en el Centro Láser de la Universidad Politécnica de Madrid y ha consistido en la caracterización mecánica y superficial del acero AISI 316L tras haber sido tratado mediante el tratamiento “Laser peening” y el estudio de la estabilidad de las tensiones residuales inducidas al ser sometido a un tratamiento a 500ºC durante dos horas. El tratamiento LSP es un tratamiento mecánico superficial que consiste en la creación de ondas de choque ...

Thermogalvanic corrosion and galvanic effects of copper and AISI 316L stainless steel pairs in heavy LiBr brines under hydrodynamic conditions

International Nuclear Information System (INIS)

Sánchez-Tovar, R.; Montañés, M.T.; García-Antón, J.

2012-01-01

Highlights: ► Thermogalvanic corrosion results in an increase of the current densities. ► Thermogalvanic effect increases as temperature difference between tubes is higher. ► Potentials fit linearly with increase in temperature. ► ZRA shows hot cathodes for AISI 316L while cold ones for copper and galvanic pairs. ► Weight loss tests show a combined effect between thermogalvanic and galvanic effects. - Abstract: Thermogalvanic corrosion of the copper/copper and AISI 316L/AISI 316L stainless steel pairs was studied in heavy lithium bromide brines under hydrodynamic conditions. The galvanic coupling effect between copper and stainless steel was also analysed. The cold electrode (25 °C) was the stainless steel for the galvanic pair, whereas copper temperature varied (25, 50 and 75 °C). A hydrodynamic circuit was designed to study thermogalvanic corrosion by means of the zero resistance ammeter technique. Hot cathodes take place in stainless steel pairs while cold cathodes are present in copper/copper and stainless steel/copper pairs; this agrees with the thermal temperature coefficient of the potential sign. Thermogalvanic corrosion increases corrosion rates, especially working with copper. Weight loss measurements show that there is a combined effect due to the thermogalvanic and the galvanic effects.

Irradiation-induced creep in 316 and 304L stainless steels

International Nuclear Information System (INIS)

Walters, L.C.; McVay, G.L.; Hudman, G.D.

1977-01-01

Recent results are presented from the in-reactor creep experiments that are being conducted by Argonne National Laboratory. The experiments consist of four subassemblies that contain helium-pressurized as well as unstressed capsules of 316 and 304L stainless steels in several metallurgical conditions. Experiments are being irradiated in row 7 of the EBR-II sodium-cooled fast breeder reactor. Three of the subassemblies are being irradiated at temperatures near 400 0 C, and the fourth subassembly is being irradiated at a temperature of 550 0 C. Creep and swelling strains were determined by profilometer measurements on the full length of the capsules after each irradiation cycle. The accumulated neutron dose on the 304L capsules at 385 0 C was 45 dpa; on the 316 capsules at 400 0 C, 40 dpa; and on the 316 capsules at 550 0 C, 25 dpa. It was found that the in-reactor creep rates were linearly dependent on hoop stress, with the exception being capsules of 316 stainless steel that had been given long-term carbide aging treatment and then irradiated at 550 0 C. Those capsules exhibited much higher creep and swelling rates than their unaged counterparts. For the metallurgical conditions where significant swelling was observed (solution-annealed 304L and aged 316 stainless steels), it was found that the in-reactor creep rates were readily fit to a model that related the creep rates to accumulated swelling. Additionally, it was found that the stress-normalized creep rate for 20%-cold-worked 316 stainless steel at a temperature of 550 0 C was 1.6 times that observed at 400 0 C

Multitechnique characterisation of 304L surface states oxidised at high temperature in steam and air atmospheres

Energy Technology Data Exchange (ETDEWEB)

Mamede, Anne-Sophie, E-mail: anne-sophie.mamede@ensc-lille.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Nuns, Nicolas, E-mail: nicolas.nuns@univ-lille1.fr [University Lille, CNRS, ENSCL, Centrale Lille, University Artois, UMR 8181 – UCCS – Unité de Catalyse et Chimie du Solide, F-59000 Lille (France); Cristol, Anne-Lise, E-mail: anne-lise.cristol@ec-lille.fr [University Lille, CNRS, Centrale Lille, Arts et Métiers Paris Tech, FRE 3723 – LML – Laboratoire de Mécanique de Lille, F-59000 Lille (France); Cantrel, Laurent, E-mail: laurent.cantrel@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); Souvi, Sidi, E-mail: sidi.souvi@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES, Cadarache, Saint Paul lez Durance, 13115 (France); Laboratoire de Recherche Commun IRSN-CNRS-Lille 1: «Cinétique Chimique, Combustion, Réactivité» (C3R), Cadarache, Saint Paul lez Durance, 13115 (France); and others

2016-04-30

Graphical abstract: - Highlights: • Mutitechnique characterisation of oxidised 304L. • Oxidation at high temperature under steam and air conditions of 304L stainless steel. • Chromium and manganese oxides formed in the outer layer. • Oxide profiles differ in air or steam atmosphere. - Abstract: In case of a severe accident occurring in a nuclear reactor, surfaces of the reactor coolant system (RCS), made of stainless steel (304L) rich in Cr (>10%) and Ni (8–12%), are oxidised. Fission products (FPs) are released from melt fuel and flow through the RCS. A part of them is deposited onto surfaces either by vapour condensation or by aerosol deposition mechanisms. To be able to understand the nature of interactions between these FPs and the RCS surfaces, a preliminary step is to characterize the RSC surface states in steam and air atmosphere at high temperatures. Pieces of 304L stainless steel have been treated in a flow reactor at two different temperatures (750 °C and 950 °C) for two different exposition times (24 h and 72 h). After surfaces analysing by a unique combination of surface analysis techniques (XPS, ToF-SIMS and LEIS), for 304L, the results show a deep oxide scale with multi layers and the outer layer is composed of chromium and manganese oxides. Oxide profiles differ in air or steam atmosphere. Fe{sub 2}O{sub 3} oxide is observed but in minor proportion and in all cases no nickel is detected near the surface. Results obtained are discussed and compared with the literature data.

Behavior to the fracture of an AISI 304 stainless steel sensitized in BWR reactor conditions (288 degrees Centigrade and 80 Kg/cm2)

International Nuclear Information System (INIS)

Hernandez C, R.; Diaz S, A.; Garcia R, R.; Aguilar T, A.; Gachuz M, M.; Arganis J, C.; Merino C, J.

1999-01-01

It is a knew fact that ductility of a lot of structural alloys can be deteriorated by the environment effect which are exposed, and that their consequent embrittlement can put in doubt the safety of their functioning; such is the case of austenitic stainless steels used in internal components of the BWR type reactors which not only is subjected to the effect combined of the aggressive environment which surround it (pressure, temperature, corrosion potential, conductivity medium, local state of efforts, etc.), but also to the action of present neutron radiation, manifesting microstructural changes which are reflected in the augmentation of its susceptibility to the intergranular cracking, phenomena generally known as IASCC ''Irradiation Assisted Stress Corrosion Cracking''. Once appeared the cracking in the material, the useful life of a component is limited by the rapidity to growth of these cracking, making necessary evaluations which can to predict its behavior, therefore the present work shows the preliminary results for determining the behavior to the fracture of an AISI 304 stainless steel sensitized, in a dynamic recirculation circuit which allows to simulate the operation conditions of a BWR reactor (288 Centigrade and 80 kg/cm 2 ). (Author)

Formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo Biofilm formation by Aeromonas hydrophila and Staphylococcus aureus on stainless steel using milk and different conditions of cultivation

Directory of Open Access Journals (Sweden)

Cleube Andrade Boari

2009-12-01

Full Text Available O objetivo desta pesquisa consistiu em avaliar a formação de biofilme em aço inoxidável por Aeromonas hydrophila e Staphylococcus aureus usando leite e diferentes condições de cultivo. As variáveis em estudo consistem no cultivo monoespécie e combinado, dos referidos microrganismos e nas temperaturas de 4, 7 e 18 °C. Recipientes contendo 1000 mL de leite, densidade populacional de 10(5 UFC.mL-1 de cada microrganismo e 10 cupons de aço inoxidável (10 × 20 mm foram lacrados e armazenados, sob agitação de 60 rpm, por um período de 10 dias. As análises ocorreram a cada 48 horas. Células sésseis de A.hydrophila e S. aureus foram enumeradas através do plaqueamento seletivo em ágar m-Aeromonas selective e Baird-Parker, respectivamente. Estudos sobre o tempo de geração, enumeração de células planctônicas e observação dos cupons através da microscopia eletrônica de varredura foram conduzidos. S. aureus, em monocultivo, formou biofilme a 18 °C e a 7 °C. Para 4 °C, foi observado um processo de adesão. A presença de A. hydrophila reduziu o desempenho de S. aureus. Nesta condição de cultivo multiespécie houve formação de biofilme a 18 °C. A. hydrophila, tanto em monocultivo quanto em presença de S. aureus, formou biofilme em todas as condições pesquisadas.The aim of this research was to verify the capability of biofilm formation on stainless steel by Aeromonas hydrophila and Staphylococcus aureus using milk and different conditions of cultivation. The variables consisted in mono and multi-species cultivation of these microorganisms and in the temperatures of 4, 7 and 18 °C. Containers containing 1000 mL of milk, population density of 10(5 CFU.mL-1 of each microorganism, and ten suspended chips of stainless steel AISI 304 (10 × 20 mm were used to seal up and storage, under 60 rpm of agitation for 10 days. The analyses were conducted every 48 hours. Sessile cells of A. hydrophila and S. aureus and were enumerated

Application of the EPR technique in welded couplings in 08X18H10T (AISI 321) stainless steel

International Nuclear Information System (INIS)

Fuentes, D.A.; Menendez, C.M.; Dominguez, H.; Sendoya, F.

1993-01-01

Stainless steel samples, one AISI 304 and the other 08X18H10T of Soviet origin (equivalent to AISI 320) were welded for the TIG method, submitted to a thermal treatment in order to its sensitization against the intergranular corrosion, then the samples were submitted to the EPR technique in order to establish the sensitization degree which is an indicative of susceptibility to intergranular corrosion. The result were corroborated by two different methodologies, the ASTM A262 standard and the soviet standard GOST 6032-89. The state of the tested surface was analyzed using optical microscopy in order to quantify the number of pricking since its presence disturbs the normalized charge, Pa. (Author)

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

OpenAIRE

Cooper, Adam J.; Sherry, Andrew

2018-01-01

Herein, we have performed J-Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP’d) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (− 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J0.2BL, when compared to equivalently graded forged 304L, which is relatively constant...

Identificación de aceros por espectroscopia de rompimiento inducido por láser (LIBS) y análisis de componentes principales

OpenAIRE

Contreras, U.; Meneses-Nava, M.A.; Torres-Armenta, D.; Robles-Camacho, J.; Barbosa-García, O.

2012-01-01

En la actualidad existe una producción de mas de 100 000 aceros diferentes de acuerdo a su composición química y propiedades mecánicas; sin embargo, una vez en el mercado, no existe técnica alguna capaz de identificar y clasificar cualquier acero según su clase o grado. En este trabajo se describe un método capaz de identificar y clasificar aceros a través de la determinación de su composición química. El método propuesto se basa en un análisis de espectroscopia atómica procedente de la técni...

Weld solidification cracking in 304 to 304L stainless steel

Energy Technology Data Exchange (ETDEWEB)

Hochanadel, Patrick W [Los Alamos National Laboratory; Lienert, Thomas J [Los Alamos National Laboratory; Martinez, Jesse N [Los Alamos National Laboratory; Martinez, Raymond J [Los Alamos National Laboratory; Johnson, Matthew Q [Los Alamos National Laboratory

2010-01-01

A series of annulus welds were made between 304 and 304L stainless steel coaxial tubes using both pulsed laser beam welding (LBW) and pulsed gas tungsten arc welding (GTAW). In this application, a change in process from pulsed LBW to pulsed gas tungsten arc welding was proposed to limit the possibility of weld solidification cracking since weldability diagrams developed for GTAW display a greater range of compositions that are not crack susceptible relative to those developed for pulsed LBW. Contrary to the predictions of the GTAW weldability diagram, cracking was found. This result was rationalized in terms of the more rapid solidification rate of the pulsed gas tungsten arc welds. In addition, for the pulsed LBW conditions, the material compositions were predicted to be, by themselves, 'weldable' according to the pulsed LBW weldability diagram. However, the composition range along the tie line connecting the two compositions passed through the crack susceptible range. Microstructurally, the primary solidification mode (PSM) of the material processed with higher power LBW was determined to be austenite (A), while solidification mode of the materials processed with lower power LBW apparently exhibited a dual PSM of both austenite (A) and ferrite-austenite (FA) within the same weld. The materials processed by pulsed GT A W showed mostly primary austenite solidification, with some regions of either primary austenite-second phase ferrite (AF) solidification or primary ferrite-second phase austenite (FA) solidification. This work demonstrates that variations in crack susceptibility may be realized when welding different heats of 'weldable' materials together, and that slight variations in processing can also contribute to crack susceptibility.

Evaluation of Mechanical Properties and Fatigue Behavior of STS 304L due to Plastic Working

Energy Technology Data Exchange (ETDEWEB)

Shim, Hyun-Bo [Yeungnam Univ., Daegu (Korea, Republic of); Kim, Young-Kyun [KOGAS Research Institute, Seoul (Korea, Republic of); Suh, Chang-Min [Kyungpook Nat’l Univ., Daegu (Korea, Republic of)

2017-07-15

The purpose of this study is to investigate the influence of the cold reduction rate and an ultrasonic fatigue test (UFT) on the fatigue behaviors of STS 304L. The tensile strength, yield strength, hardness value and fatigue limit in the UFT fatigue test linearly increased as thickness decreased from 1.5 mm to 1.1 mm, as the cold reduction rate of STS 304L increased. As a result of the UFT fatigue test (R = -1) of four specimens, the fatigue limit of the S-N curve formed a knee point in the region of 10{sup 6}, and the 2nd fatigue limit caused by giga cycle fatigue did not appeared. In the case of t = 1.1 mm, the highest fatigue limit was 345 MPa, which was 64.3% higher than the original material (t = 1.5 mm). As a result of the UFT fatigue test of STS 304L, many small surface cracks occurred, grown, coalesced while tearing.

Reciclado de las aguas de decapado

Directory of Open Access Journals (Sweden)

López, F. A.

1998-05-01

Full Text Available Pickling liquors from steel industry, listed as hazardous wastes in most industrializated countries, have been treated by means of several procedures in order to recover the iron and other metals and to obtain an environmental friendly effluent. Depending on the treatment employed, different valuable ferrous products have been obtained. Ammoniojarosite and zinc ferrite were precipitated from the previously oxidised ferrous solutions.

En la mayoría de los países industrializados, se incluyen las aguas de decapado, tanto las procedentes de los aceros al carbono como de aceros inoxidables, dentro de las listas de residuos tóxicos y peligrosos. Se presentan en este trabajo los resultados obtenidos en las investigaciones realizadas en los últimos años en los que se ha estudiado el tratamiento y recuperación de aguas de decapado de aceros comunes e inoxidables. Su tratamiento se ha enfocado hacia la consecución de dos objetivos: la recuperación del contenido total de metales y la obtención de un efluente de menor impacto ambiental. Se presentan los procedimientos estudiados para la obtención de compuestos de hierro, amoniojarosita y ferritas de zinc, con cierto valor añadido.

Dermatitis de contacto por prótesis ortopédicas Contact dermatitis for orthopaedic prostheses

Directory of Open Access Journals (Sweden)

C.A. Danielo

2007-09-01

Full Text Available Diversas aleaciones son utilizadas en la fabricación de prótesis ortopédicas (ej: titanio, vitalio, etc, dentro de las cuales la más utilizada es la de acero inoxidable. El níquel, parte importante de esta aleación, es capaz de liberarse y provocar sensibilización, desencadenando reacciones cutáneas locales y sistémicas. De los materiales que componen la aleación para formar acero inoxidable, el níquel es el que más frecuentemente se ve implicado en reacciones cutáneas por sensibilidad, en tanto que otros como el cromo y cobalto, la posibilidad de pérdida de material a partir de la prótesis es discutida. Presentamos el caso de una paciente con dermatitis alérgica al níquel con lesiones generalizadas, que aparecieron luego del implante de prótesis ortopédicas de acero inoxidable, dando positivo para níquel sulfato en las pruebas epicutáneas.Several alloys are used in the manufacture of orthopaedics prostheses (ie: titanium, vitalium. Stainless steel is the most frequently used among them. Nickel is an important component of this alloy and may release and provoke sensitivity. Arising local and systemic cutaneous reactions. Nickel is the material composing stainless steel that ordinary is implicated in cutaneous reactions of sensitivity; the role of chrome or cobalt is still uncertain. Our patient is a woman affected of nickel contact dermatitis, with generalized reactions that appear after an implant of a stainless steel orthopaedic prosthesis. Epicutaneous tests were performed, confirming a strong sensitivity to nickel sulphate.

Lubricación del contacto aluminio-acero con líquidos iónicos en atmósfera controlada

OpenAIRE

Llopis Morales, Miguel

2016-01-01

El objetivo del presente proyecto es estudiar el comportamiento tribológico de diferentes líquidos iónicos en el contacto aluminio-acero y las interacciones superficiales que se producen. Para realizar el estudio tribológico, se llevará a cabo un estudio de corrosión previo por lo que será necesario realizar ensayos de corrosión y tribológicos. En cuanto a los objetivos de los ensayos de corrosión, el objetivo que se quiere alcanzar con este ensayo es comprobar si se produce algún tipo de cor...

Influencia del acabado superficial en la permeación de hidrógeno del acero API 5L-X52

Directory of Open Access Journals (Sweden)

Réquiz, R.

2004-02-01

Full Text Available The influence of surface roughness on the corrosion and hydrogen permeation behaviour was evaluated on a type API 5L-X52 steel in deaerated 0.1 M Na₂SO₄ at pH=2. Potentiodynamic polarization curves were employed to determine the electrochemical behaviour of the steel, while the Devanathan-Stachurski technique was used to estimate the hydrogen permeation rate. Additionally, the surface roughness profiles were obtained in order to correlate the changes in the hydrogen permeation rate with different metal surface finishings. The obtained results clearly demonstrate that when the roughness parameters have larger values, the cathodic current of hydrogen evolution increases while the hydrogen entry rate decreases. This effect can be attributed to the microstructural defects induced at the steel surface, such as dislocations, which increase the catalytic activity of the atomic hydrogen favouring its recombination. Also, these defects could allow the atomic hydrogen to remain adsorbed on the steel surface. Both effects could hinder the hydrogen diffusion into the metal since the possibility for this atom of becoming absorbed has been reduced

En el presente trabajo de investigación se evalúa la influencia del acabado superficial, tanto en la corrosión generalizada como en la permeación de hidrógeno del acero API 5L-X52 en solución de Na₂SO₄ 0,1M, a pH=2. El comportamiento electroquímico del acero se estudió mediante las curvas de polarización potenciodinámicas, mientras que la susceptibilidad al daño por hidrógeno se evaluó mediante la técnica de permeación de Devanathan- Stachurski. Además, se determinaron los parámetros de rugosidad a las muestras de acero con diferentes acabados superficiales, para luego correlacionarlos con los cambios en las corrientes de permeación de hidrógeno. Los resultados obtenidos demuestran, claramente, que, cuando la rugosidad superficial del acero

Pre- and postirradiation properties of brazed joints of AISI 316L stainless steel

International Nuclear Information System (INIS)

Brossa, M.; Franconi, E.; Guerreschi, U.; Pierazzi, L.; Poggi, P.; Rustia, V.

1994-01-01

An extensive test campaign has been performed to verify the reliability and the endurance of brazed joints between AISI 316L parts for structural applications in the nuclear field. The tests, conducted for comparison with three different high melting temperature alloys, included tensile tests (normal and shear), fatigue tests (fatigue crack propagation, low cycle fatigue, 4-point bending fatigue) and impact tests; besides, tensile tests have been performed with both unirradiated and irradiated specimens. Generally, the tests demonstrated satisfactory mechanical properties of the joints and revealed occasionally strong differences in the behaviour of the different brazing alloys, thus providing important design indications. ((orig.))

Effect of Temperature on the Fracture Toughness of Hot Isostatically Pressed 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Brayshaw, W. J.; Sherry, A. H.

2018-03-01

Herein, we have performed J- Resistance multi-specimen fracture toughness testing of hot isostatically pressed (HIP'd) and forged 304L austenitic stainless steel, tested at elevated (300 °C) and cryogenic (- 140 °C) temperatures. The work highlights that although both materials fail in a pure ductile fashion, stainless steel manufactured by HIP displays a marked reduction in fracture toughness, defined using J 0.2BL, when compared to equivalently graded forged 304L, which is relatively constant across the tested temperature range.

Cyclic oxidation of stainless steel ferritic AISI 409, AISI 439 and AISI 441; Oxidacao ciclica dos acos inoxidaveis ferriticos AISI 409, AISI 439 e AISI 441

Energy Technology Data Exchange (ETDEWEB)

Salgado, Maria de Fatima; Santos, Diego Machado dos; Oliveira, Givanilson Brito de, E-mail: fatima.salgado@pq.cnpq.br [Universidade Estadual do Maranhao (CESC/UEMA), Caxias, MA (Brazil). Centro de Estudos Superiores; Rodrigues, Samara Clotildes Saraiva; Brandim, Ayrton de Sa [Instituto Federal do Piaui (PPGEM/IFPI), PI (Brazil); Lins, Vanessa de Freitas Cunha [Universidade Federal de Minas Gerais (IFMG), MG (Brazil)

2014-07-01

Stainless steels have many industrial applications. The cyclic oxidation of ferritic stainless steels technical and scientific importance presents, because they are less susceptible to peeling the austenitic alloys. For the purpose of investigating the behavior of these steels under thermal cycling, cyclic oxidation of AISI 409, AISI 441 and AISI 439 was carried out in a tubular furnace under two different conditions: oxidation by dipping the steel in the synthetic condensate for 10h and without oxidation immersion in the condensate, for up to 1500h at 300° C temperature. Using techniques: SEM, EDS and XRD revealed a microstructure with increased oxidation in the samples were immersed in the condensate. The oxide film remained intact during oxidation for steels 439 and 441 409 The Steel immersed in the condensate was rupture of the film after the 20th cycle of oxidation. The chemical characterization of the films allowed the identification of elements: Chromium, Iron, Aluminium and Silicon To a great extent, Cr{sub 2}O{sub 3}. (author)

Tribological behavior of an austenitic stainless steel AISI 316L nitrurated by DC-pulsed plasma

International Nuclear Information System (INIS)

De Las Heras, E; Walther, F; Corengia, P.A; Quinteiro, M.O; Cabo, A; Bruhl, S; Sommadossi, S

2004-01-01

Austenitic stainless steels are widely used in different applications because they withstands corrosion. Ionic nitruration has proven to be an adequate technique for modifying this type of steel, in order to improve its resistance to wear without diminishing its resistance to corrosion. While many publications have reported improvements in the tribological properties of the nitrurated AISI 316, systematic studies that evaluate this behavior using industrial equipment for its thermochemical treatment are of interest. This work studied the tribological behavior of an AISI 316L steel nitrurated by DC pulsed plasma in an industrial machine in an atmosphere of 25% N 2 and 75% H 2 for 20 h at 400 o C by means of abrasion tests under different conditions in an A 135 Amsler-disk machine. In order to characterize the abraded samples microhardness, optic and scanning electron microscopy profiles to determine the abrasion mechanisms were performed. The results showed substantial improvement in the abrasion resistance of the nitrurated samples compared to the non nitrurated ones and the different abrasion mechanisms are discussed to explain the test results (CW)

Effect of Prior Deformation on Welding Microstructure of Steel 304L

Directory of Open Access Journals (Sweden)

WU Luo-fei

2017-01-01

Full Text Available This subject was raised by an automotive company.Based on the welding design on the curved surface,the effect of prior deformation on the weld structure was studied.Metal active-gas welding was used on the T-joint and pre-deformed plates of austenitic stainless steel 304L to find the proper welding parameters and observe the effect of prior deformation on the microstructure.The proper parameters acquired are:the speed of the torch is 4mm/s,the speed of delivery of welding wire is 2.5m/min and the voltage is 17V.In the T-joint and pre-deformed joint,the weld toes are in the zone with strain of 0% and 30%.In the pre-deformed welding specimen,it was observed that the fusion zone and partially melted zone are narrowed,carbide precipitation and ferrites are found less.In all,the microstructure in the pre-deformed weld joints on 304L is more uniform.

Estudio del comportamiento a fluencia en caliente de un acero avanzado de alta resistencia de bajo contenido en carbono NiCrVCu microaleado con boro

OpenAIRE

González Sala, Sara

2009-01-01

Una de las líneas de investigación prioritarias en el contexto internacional es el desarrollo de aceros avanzados de alta resistencia (AHSS) con excelentes propiedades de resistencia y tenacidad para aplicaciones en la industria automotriz, naval, aeronáutica y de generación de energía, que permitan disminuir el peso de los componentes y sustituyan aceros tradicionales de contenidos mayores de carbono. Los aceros AHSS microaleados al boro, debido a sus cualidades, tecnología de...

Evaluation of performance of AISI 444 steel for application in distillation towers; Avaliacao do desempenho do aco AISI 444 para aplicacao como 'lining' em torres de destilacao

Energy Technology Data Exchange (ETDEWEB)

Guimaraes, R.F.; Miranda, H.C. de; Farias, J.P. [Universidade Federal do Ceara (DEMM/UFC), Fortaleza, CE (Brazil). Dept. de Engenharia Metalurgica e de Materiais. Lab. de Caracterizacao de Materiais], e-mail: rf.guimaraes@yahoo.com.br

2008-07-01

In this work, the behavior of the AISI 444 ferritic stainless steel submitted to thermal fatigue test and their corrosion resistance in heavy crude oil was evaluated. The AWS E309MoL-16 and E316L-17 weld metal was employed as filler metal. Plates of the AISI 444 were welded on ASTM A-516 Gr. 60 plates and submitted to fatigue thermal cycle. Samples were extracted from plates welded and heat treated immersed in heavy crude oil at 300 deg C. Optical microscopy (OM), scanning electron microscopy (SEM) and energy dispersive of X-ray analysis (EDX) were used to characterize the microstructure and the corroded surface. The results show that the AISI 444 stainless steels did not present cracks after the thermal fatigue cycle and the heat treated immerse in heavy crude oil. The electrode AWS E309MoL-16 show better corrosion resistance than the AWS E316L-17. (author)

Adhesion of composite carbon/hydroxyapatite coatings on AISI 316L medical steel

Directory of Open Access Journals (Sweden)

J. Gawroński

2009-07-01

Full Text Available In this paper are contains the results of studies concerning the problems associated with increased of hydroxyapatite (HAp adhesion, manufactured by using Pulse Laser Deposition (PLD method, to the austenitic steel (AISI 316L through the coating of carbon interlayer on it. Carbon coating was deposited by Radio Frequency Plasma Assisted Chemical Vapour Deposition (RF PACVD method.Test results unequivocally showed that the intermediate carbon layer in a determined manner increase the adhesion of hydroxyapatite to the metallic substrate. Obtained results give rise to deal with issues of manufacturing composite bilayer – carbon film/HAp – on ready implants, casted from austenitic cast steel by lost-wax process method as well as in gypsum forms.

Corrosion behaviour of electropolished AISI 316L austenitic biomaterial in physiological solution

Science.gov (United States)

Zatkalíková, V.; Markovičová, L.; Škorvanová, M.

2017-11-01

Due to suitable mechanical properties, satisfactory corrosion resistance and relatively low cost, austenitic stainless steels are important biomaterials for manufacture of implants and various medical instruments and devices. Their corrosion properties and biocompatibility are significantly affected by protective passive surface film quality, which depends on used mechanical and chemical surface treatment. This article deals with corrosion resistance of AISI 316L stainless steel, which is the most widely used Cr-Ni-Mo austenitic biomaterial. Corrosion behaviour of five various surfaces (original, electropolished, three surfaces with combined treatment finished by electropolishing) is evaluated on the bases of cyclic potentiodynamic polarization tests performed in physiological solution at the temperature of 37± 0.5 °C.

Effect of V addition on the hardness, adherence and friction coefficient of VC coatings produced by thermo-reactive diffusion deposition

OpenAIRE

Fredy Alejandro Orjuela-Guerrero; José Edgar Alfonso-Orjuela; Jhon Jairo Olaya-Flórez

2015-01-01

Se produjeron recubrimientos de carburo de vanadio (VC) sobre sustratos de acero AISI H13 y acero AISI D2 mediante deposito termoreactiva/ difusión (TRD) con el fin de evaluar sus propiedades mecánicas como una función del contenido de vanadio. Los recubrimientos se producen con diferentes porcentajes de concentración de ferrovanadio. La composición química de los recubrimientos se determinó mediante fluorescencia de rayos X (XRF), la estructura cristalina se analizó utilizando difracción de ...

Corrosion fatigue of AISI 304 stainless steel in aqueous chloride solution

International Nuclear Information System (INIS)

Ferrao, P.R.; Sousa e Silva, A.S. de; Castro, M.A.C. de

1982-01-01

The fatique behaviour of an 304 austenitic stainless steel in a 0,5 M NaCl environment was studied. The material was tested, under different electrode potential conditions and the results were compaired with those obtained for tests in air. It has been shown by means of metallographic and fractografic observations, that the mechanism of crack initiation depends on the applied potential. (Author) [pt

Comportamiento de las aleaciones termorresistentes AISI HH y HK-40 ante los procesos de carburización y nitruración

Directory of Open Access Journals (Sweden)

Eleno Alfonso-Brindis

2001-03-01

Full Text Available Se evalúa el comportamiento de los aceros austeníticos fundidos AISI HH y HK- 40 (de producción nacional ante los procesos de carburización y nitruración en los rangos de temperaturas desde 750 hasta 1 000 °C. Se estudia la cinética y la termodinámica de las posibles reacciones y los productos de las mismas se caracterizan mediante técnicas de Microscopía Óptica, Microscopía Electrónica de Barrido y Microanálisis (MEB-EDAX. En el análisis microscópico se observó la formación de carburos de cromo después de la carburización, mientras que la nitruración dio lugar a la formación de nitruros de cromo. Se concluye que la aleación AISI HK-40 posee una elevada resistencia intrínseca a la carburización y a la nitruración, que hace factible su empleo en componentes de hornos de soleras múltiples para la reducción de minerales lateríticos

Laser welding of NiTi shape memory alloy: Comparison of the similar and dissimilar joints to AISI 304 stainless steel

Science.gov (United States)

Mirshekari, G. R.; Saatchi, A.; Kermanpur, A.; Sadrnezhaad, S. K.

2013-12-01

The unique properties of NiTi alloy, such as its shape memory effect, super-elasticity and biocompatibility, make it ideal material for various applications such as aerospace, micro-electronics and medical device. In order to meet the requirement of increasing applications, great attention has been given to joining of this material to itself and to other materials during past few years. Laser welding has been known as a suitable joining technique for NiTi shape memory alloy. Hence, in this work, a comparative study on laser welding of NiTi wire to itself and to AISI 304 austenitic stainless steel wire has been made. Microstructures, mechanical properties and fracture morphologies of the laser joints were investigated using optical microscopy, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD), Vickers microhardness (HV0.2) and tensile testing techniques. The results showed that the NiTi-NiTi laser joint reached about 63% of the ultimate tensile strength of the as-received NiTi wire (i.e. 835 MPa) with rupture strain of about 16%. This joint also enabled the possibility to benefit from the pseudo-elastic properties of the NiTi component. However, tensile strength and ductility decreased significantly after dissimilar laser welding of NiTi to stainless steel due to the formation of brittle intermetallic compounds in the weld zone during laser welding. Therefore, a suitable modification process is required for improvement of the joint properties of the dissimilar welded wires.

An Assessment of the Ductile Fracture Behavior of Hot Isostatically Pressed and Forged 304L Stainless Steel

Science.gov (United States)

Cooper, A. J.; Smith, R. J.; Sherry, A. H.

2017-05-01

Type 300 austenitic stainless steel manufactured by hot isostatic pressing (HIP) has recently been shown to exhibit subtly different fracture behavior from that of equivalent graded forged steel, whereby the oxygen remaining in the component after HIP manifests itself in the austenite matrix as nonmetallic oxide inclusions. These inclusions facilitate fracture by acting as nucleation sites for the initiation, growth, and coalescence of microvoids in the plastically deforming austenite matrix. Here, we perform analyses based on the Rice-Tracey (RT) void growth model, supported by instrumented Charpy and J-integral fracture toughness testing at ambient temperature, to characterize the degree of void growth ahead of both a V-notch and crack in 304L stainless steel. We show that the hot isostatically pressed (HIP'd) 304L steel exhibits a lower critical void growth at the onset of fracture than that observed in forged 304L steel, which ultimately results in HIP'd steel exhibiting lower fracture toughness at initiation and impact toughness. Although the reduction in toughness of HIP'd steel is not detrimental to its use, due to the steel's sufficiently high toughness, the study does indicate that HIP'd and forged 304L steel behave as subtly different materials at a microstructural level with respect to their fracture behavior.

Funcionalización electroquímica y tribológica de películas de quitosano en fosfato tricálcico depositados en acero 316L

Directory of Open Access Journals (Sweden)

Alexis Mina Escobar

2013-12-01

Full Text Available Se depositaron recubrimientos de fosfato tricálcico-β/quitosano sobre sustratos de acero 316L vía electrodeposición, a una temperatura de 60 °C, aplicando una corriente de 260 mA. Con el fin de estudiar el efecto del contenido de quitosano en la velocidad de corrosión y la respuesta tribológica de los aceros recubiertos, se utilizaron seis concentraciones de quitosano en la mezcla acuosa. Los enlaces químicos presentes en las capas fueron estudiados mediante Espectroscopia de Infrarrojo con Transformada de Fourier (FTIR; la cristalinidad de los depósitos fue examinada mediante difracción de rayos-X (DRX; la resistencia a la corrosión del TCP-β/quitosano depositado sobre los aceros se estudió mediante Espectroscopia de Impedancia Electroquímica (EIS y curvas anódicas Tafel, encontrándose una disminución del 54% en la velocidad de corrosión para la relación 50-50, con respecto a 100% TCP. La respuesta tribológica se analizó mediante pin-on-disc, evidenciando una reducción del 73% en el coeficiente de fricción con mayor concentración de quitosano.

Intergranular stress corrosion cracking of ion irradiated 304L stainless steel in PWR environment

International Nuclear Information System (INIS)

Gupta, Jyoti

2016-01-01

IASCC is irradiation - assisted enhancement of intergranular stress corrosion cracking susceptibility of austenitic stainless steel. It is a complex degrading phenomenon which can have a significant influence on maintenance time and cost of PWRs' core internals and hence, is an issue of concern. Recent studies have proposed using ion irradiation (to be specific, proton irradiation) as an alternative of neutron irradiation to improve the current understanding of the mechanism. The objective of this study was to investigate the cracking susceptibility of irradiated SA 304L and factors contributing to cracking, using two different ion irradiations; iron and proton irradiations. Both resulted in generation of point defects in the microstructure and thereby causing hardening of the SA 304L. Material (unirradiated and iron irradiated) showed no susceptibility to intergranular cracking on subjection to SSRT with a strain rate of 5 * 10 -8 s -1 up to 4 % plastic strain in inert environment. But, irradiation (iron and proton) was found to increase intergranular cracking severity of material on subjection to SSRT in simulated PWR primary water environment at 340 C. Correlation between the cracking susceptibility and degree of localization was studied. Impact of iron irradiation on bulk oxidation of SA 304L was studied as well by conducting an oxidation test for 360 h in simulated PWR environment at 340 C. The findings of this study indicate that the intergranular cracking of 304L stainless steel in PWR environment can be studied using Fe irradiation despite its small penetration depth in material. Furthermore, it has been shown that the cracking was similar in both iron and proton irradiated samples despite different degrees of localization. Lastly, on establishing iron irradiation as a successful tool, it was used to study the impact of surface finish and strain paths on intergranular cracking susceptibility of the material. (author) [fr

Cyclic oxidation of stainless steel ferritic AISI 409, AISI 439 and AISI 441

International Nuclear Information System (INIS)

Salgado, Maria de Fatima; Santos, Diego Machado dos; Oliveira, Givanilson Brito de; Lins, Vanessa de Freitas Cunha

2014-01-01

Stainless steels have many industrial applications. The cyclic oxidation of ferritic stainless steels technical and scientific importance presents, because they are less susceptible to peeling the austenitic alloys. For the purpose of investigating the behavior of these steels under thermal cycling, cyclic oxidation of AISI 409, AISI 441 and AISI 439 was carried out in a tubular furnace under two different conditions: oxidation by dipping the steel in the synthetic condensate for 10h and without oxidation immersion in the condensate, for up to 1500h at 300° C temperature. Using techniques: SEM, EDS and XRD revealed a microstructure with increased oxidation in the samples were immersed in the condensate. The oxide film remained intact during oxidation for steels 439 and 441 409 The Steel immersed in the condensate was rupture of the film after the 20th cycle of oxidation. The chemical characterization of the films allowed the identification of elements: Chromium, Iron, Aluminium and Silicon To a great extent, Cr_2O_3. (author)

Development of a Novel Approach for Fatigue Life Prediction of Structural Materials

Science.gov (United States)

2008-12-01

Mughrabi, H., 1989, "Plasticity-Induced Martensitic Transformation of AISI 304L Stainless Steel ," Mat Sci Eng A114, pp. LI 1-LI 6. [26] Krupp, U...four structural materials: aluminum 7075T651 alloy, stainless steel AL6-XN, stainless steel 304L, and Aerospace Steel 4340. It was confirmed that...four structural materials: aluminum 7075T651 alloy, stainless steel AL6-XN, stainless steel 304L, and Aerospace Steel 4340. Fatigue and cyclic

Corrosion testing of a degraded moderator: L-Area Tuff Tanks

International Nuclear Information System (INIS)

Mickalonis, J.I.

2000-01-01

Based on test results, storage of the degraded moderator in 55-gallon 304L drums (0.065 inches thick) would not cause failure by general corrosion for up to 5 plus years storage. Acidic degraded moderator was temporarily stored in Tuff Tanks located in L-area. The moderator characteristics included a D 2 O content of 5.02--5.33%, a pH of 1.25--1.31, a conductivity of 29,300--31,200 m mhos/cm, tritium activity of 114--141 m Ci/mL, and levels of approximately 6,000 ppm for chloride and 500 ppm for chromium. The compatibility of the degraded with AISI Type 304L stainless steel (304L) was investigated in this study. Following ASTM standard practice, coupon immersion tests were conducted in both treated and untreated moderator. Treatment included the addition of either a 40 wt % NaOH solution, distilled water to serially dilute the chloride, or concentrated nitric acid to increase the nitrate concentration. Type 304L stainless steel exposed to the Tuff Tank moderator was found from these tests to: have a general corrosion rate of less than 5 mils per year (mpy) for 304L plate, which bounds that of the 304L storage drum, passivate at chloride concentrations up to 5,000 ppm for 304L sheet, resist corrosion for nitrate/chloride ratios ranging from 0.1 to 1,000, and be susceptible to crevice corrosion. Based on these test results, storage of the degraded moderator in 55-gallon 304L drums (0.065 inch thick) would not cause failure by general corrosion for up to 5+ years storage. The chloride concentration, [Cl], in the degraded moderator has been measured up to 6000 ppm. The potential or risk for aggressive localized attack of 304L increases with [Cl] concentration. A qualitative range is as follows: [Cl minus ] minus ] minus ] < 600 ppm, reasonable resistance, medium risk. The degraded moderator should be treated to reduce the chloride concentration to reduce the potential for localized corrosion and the risk for a leakage failure of the drum. A good practice would be to

In-reactor precipitation and ferritic transformation in neutron--irradiated stainless steels

International Nuclear Information System (INIS)

Porter, D.L.; Wood, E.L.

1978-01-01

Ferritic transformation (γ → α) was observed in Type 304L, 20% cold-worked AISI 316, and solution-annealed AISI 316 stainless steels subjected to fast neutron irradiation. Each material demonstrated an increasing propensity for transformation with increasing irradiation temperature between 400 and 550 0 C. Irradiation-induced segregation of Ni solute to precipitates was found not to influence the transformation kinetics in 304L. Similar composition data from 316 materials demonstrates a much greater temperature dependence of precipitation reactions in the process of matrix Ni depletion during neutron irradiation. The 316 data establishes a strong link between such depletion and the observed γ → α transformation. Moreover, the lack of correlation between precipitate-related Ni depletion and the γ → α transformation in 304L can be related to the fact that irradiation-induced voids nucleate very quickly in 304L steel during irradiation. These voids present preferential sites for Ni segregation through a defect trapping mechanism, and hence Ni segregates to voids rather than to precipitates, as evidenced by observed stable γ shells around voids in areas of complete transformation

Study of copper deposit on a porous electrode of carbon and stainless steel by sem-xrd and image analysis

OpenAIRE

Constanzo-R., Robinson; Pagliero-N., Antonio; Vergara-G., Froilán

2014-01-01

El objetivo de este trabajo fue realizar un análisis cualitativ o de la distribución de un electrodepósito de cobre en el inter ior de electrodos porosos (EP) de acero inoxidable y carbono grafito. Para ello, se reali zaron pruebas de electrodepositación de cobre a nivel de labora torio, con un posterior análisis de cortes de muestras de acero y grafito vía Microscopía Estereoscópica, Microscopía SEM-DRX y Análisis de Imagen, los cuales mostraron que el cobre no se deposita en forma uniforme ...

Multiaxial fatigue criteria for AISI 304 and 2-1/4 Cr-1 Mo steel at 5380C with applications to strain-range partitioning and linear summation of creep and fatigue damage

International Nuclear Information System (INIS)

Blass, J.J.

1982-01-01

An improved multiaxial fatigue failure criterion was developed based on the results of combined axial-torsional strain cycling tests of AISI 304 and 2-1/4 Cr-1 Mo steel conducted at 538 0 C (1000 0 F). The formulation of this criterion involves the shear and normal components of inelastic strain range on the planes of maximum inelastic shear strain range. Optimum values of certain parameters contained in the formulation were obtained for each material by the method of least squares. The ability of this criterion to correlate the test results was compared with that of the usual (Mises) equivalent inelastic strain range criterion. An improved definition of equivalent inelastic strain range resulting from these considerations was used to generalize the theory of Strain Range Partitioning to multiaxial stress-strain conditions and was also applied to the linear summation of creep and fatigue damage

Comportamiento frente al desgaste y fricción de aceros empleados en líneas de manutención aérea ensayados con y sin lubricación

Directory of Open Access Journals (Sweden)

Castro Regal, G.

2005-06-01

Full Text Available The sliding friction and wear behaviour of different steel qualities were investigated with and without lubrication conditions. Steel qualities tested are normally used in the overhead conveyor system of many industrial fields, like the automotive sector. Sliding wear tests have been conducted by means of a pin-on-disk machine. A 100Cr6 steel similar to that used within the overhead conveyor trolleys has been employed as a pin. Friction coefficient values obtained under lubrication conditions were three times smaller than those obtained without lubrication. The mechanism that controls wear behaviour under lubrication conditions is an abrasive one and the wear values obtained are almost worthless. On the other hand, mechanism controlling wear during non lubrication tests, was a combination of abrasion and adhesion

Se ha evaluado el comportamiento frente a fricción y el desgaste de distintas calidades de acero ensayadas bajo condiciones de lubricación y sin lubricación. Las calidades de acero seleccionadas son las que normalmente se emplean en los sistemas de manutención aérea de numerosos procesos de producción, como la fabricación de automóviles. Se han realizado ensayos de desgaste tipo punzón-disco mediante un punzón de acero de calidad100Cr6, empleado en los carros que circulan por las líneas de manutención aérea. Se ha observado que el valor del coeficiente de fricción obtenido bajo condiciones de lubricaciones, aproximadamente, tres veces menor que el obtenido sin lubricación. Por otro lado, el mecanismo que controla el proceso de desgaste de los aceros ensayados con lubricación es un mecanismo de desgaste abrasivo y los valores de desgaste obtenidos son prácticamente despreciables. El desgaste de los aceros ensayados sin lubricación se produjo por combinación de dos mecanismos de desgaste: abrasión y adhesión.

Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

Energy Technology Data Exchange (ETDEWEB)

Esguerra A, J.; Aguilar, Y. [Universidad del Valle, Escuela de Ingenieria de Materiales, TPMR, Calle 13 No. 100-00, A. A. 25360 Cali (Colombia); Aperador, W. [Escuela Colombiana de Ingenieria Julio Garavito, Escuela de Ingenieria Mecanica, AK 45 No. 205-59 (Autopista Norte), A. A. 14520 Bogota (Colombia); Alba de Sanchez, N. [Universidad Autonoma de Occidente, Grupo de Investigacion en Ciencia e Ingenieria de Materiales, Calle 25 No. 115-85, A. A. 2790 Cali (Colombia); Bolanos P, G.; Rincon, C., E-mail: johanna.esguerra@univalle.edu.co [Universidad del Cauca, Departamento de Fisica, Laboratorio de Fisica de Bajas Temperaturas, Calle 5 No. 4-70, A. A. 996 Popayan (Colombia)

2014-07-01

Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

Adherence and electrochemical behavior of calcium titanate coatings onto 304 stainless steel substrate

International Nuclear Information System (INIS)

Esguerra A, J.; Aguilar, Y.; Aperador, W.; Alba de Sanchez, N.; Bolanos P, G.; Rincon, C.

2014-01-01

Calcium titanate has been proposed as a coating for biomedical applications but it has not been reported characterization of adhesion failure mechanisms or electrochemical properties in time. In this work have been studied these properties of a calcium titanate coating growth onto AISI 304 steel deposited by r.f. magnetron sputtering. It was found that the coating has a critical adhesive load of 6.53 ± 0.14 N. With respect to its electrochemical properties potentiodynamic polarization curves show that the calcium titanate coating provides protection to AISI 304 steel. However. EIS indicates that even though metal dissolution occur through the pores in the coating, this leads to the precipitation of salts that block pores; this precipitates layer acts like and additional barrier to the metal dissolution in the system. The coatings deposition was carried out via magnetron sputtering during 4 hours at 500 grades C. The crystal structure of the films was determined by using glancing incident X-ray diffraction. The chemical composition of deposited films was performed by impedance dispersive X-ray spectroscopy (EDX) in the scanning electron microscopy (Jeol JSM-649 OLV Sem), and the grain size and the roughness was obtained using an atomic force microscopy from Asylum Research MFP-3D using a cantilever silicon tip in non-contact mode and calculated by scanning probe image processor. (Author)

Plasma Nitriding of AISI 304 Stainless Steel in Cathodic and Floating Electric Potential: Influence on Morphology, Chemical Characteristics and Tribological Behavior

Science.gov (United States)

Li, Yang; He, Yongyong; Wang, Wei; Mao, Junyuan; Zhang, Lei; Zhu, Yijie; Ye, Qianwen

2018-03-01

In direct current plasma nitriding (DCPN), the treated components are subjected to a high cathodic potential, which brings several inherent shortcomings, e.g., damage by arcing and the edging effect. In active screen plasma nitriding (ASPN) processes, the cathodic potential is applied to a metal screen that surrounds the workload, and the component to be treated is placed in a floating potential. Such an electrical configuration allows plasma to be formed on the metal screen surface rather than on the component surface; thus, the shortcomings of the DCPN are eliminated. In this work, the nitrided experiments were performed using a plasma nitriding unit. Two groups of samples were placed on the table in the cathodic and the floating potential, corresponding to the DCPN and ASPN, respectively. The floating samples and table were surrounded by a steel screen. The DCPN and ASPN of the AISI 304 stainless steels are investigated as a function of the electric potential. The samples were characterized using scanning electron microscopy with energy-dispersive x-ray spectroscopy, x-ray diffraction, atomic force microscopy and transmission electron microscope. Dry sliding ball-on-disk wear tests were conducted on the untreated substrate, DCPN and ASPN samples. The results reveal that all nitrided samples successfully produced similar nitrogen-supersaturated S phase layers on their surfaces. This finding also shows the strong impact of the electric potential of the nitriding process on the morphology, chemical characteristics, hardness and tribological behavior of the DCPN and ASPN samples.

Efectos del tratamiento térmico en la fractura de aceros

Directory of Open Access Journals (Sweden)

Héctor Hernández A.

1992-05-01

Full Text Available No obstante de los avances logrados en otros tipos de aleaciones, los aceros se siguen utilizando en forma extensiva en la construcción de elementos estructurales, porque con una adecuada selección y tratamiento técnico, los aceros permiten obtener una conveniente combinación de propiedades mecánicas ante unas exigencias específicas de servicio. La fractura en elementos de máquinas frecuentemente se encuentra asociada a una discontinuidad, la cual provoca una concentración de esfuerzo, lo que puede originar sitios de iniciación de una falla por fractura. La carga límite de fractura es afectada por parámetros geométricos, naturaleza y tipo de carga y propiedades mecánicas del material. La mayoría de fallas por fractura de elementos de máquinas son fallas por fatiga; por lo general una fractura por fatiga tiene lugar por una progresiva generación y crecimiento de grietas hasta obtenerse una condición crítica de fractura súbita de la sección residual resistente. Frecuentemente en una fractura por fatiga se observan marcas de playa, las cuales son evidencias de la posición del frente de grietas antes que se alcance la condición de fractura súbita final. En este trabajo se muestra como el tratamiento térmico de temple y revenido de los aceros afecta el esfuerzo límite de falla por fractura para carga de tracción estática y carga de fatiga uniaxial con la presencia de una entalla severa. También se estudia el efecto del tratamiento térmico en la tenacidad de fractura, propiedad que cuantifica la resistencia al crecimiento súbito de una grieta bajo carga estática.

Transferencia de calor en la colada continua de aceros. I parte. El molde

Directory of Open Access Journals (Sweden)

Cicutti, C.

1997-10-01

Full Text Available The continuous casting mold plays the important role of receiving the liquid steel and allowing an uniform and defect free solidified skin to be developed. In this work, the different heat transfer mechanisms which are present from the liquid steel to the mold cooling water are reviewed. The effect of operating variables on heat extraction and the relationship between global and distributed heat flux are also analyzed.

El molde de colada continua cumple la importante función de recibir el acero líquido y permitir que se desarrolle una capa solidificada uniforme y libre de defectos. En este trabajo se revisan los distintos mecanismos implicados en el proceso de transferencia de calor, desde el acero líquido hasta el agua de refrigeración del molde. Se analiza también el efecto de las distintas variables de funcionamiento en la extracción calórica producida y la relación entre el flujo global de calor y su distribución a lo largo del molde.

Acoustic emission from hydrogen saturated Type 304L stainless steel

International Nuclear Information System (INIS)

Caskey, G.R. Jr.

1978-01-01

Acoustic emission is attributed to energy release within a material body by localized plastic deformation or failure processes. The elastic stress waves may come from slip band formation, mechanical twinning, martensite transformation, or crack propagation. Each of these processes has slightly different acoustic characteristics allowing for easy identification. Acoustic emission was monitored during tensile tests of Type 304L austenitic stainless steel to explore the applicability of the technique to hydrogen-assisted fracture

Procesos de unión y estudio de interfaces en Si3N4 y ZrO2

OpenAIRE

Polanco Rodríguez, Raquel

2007-01-01

Esta memoria se ha centrado en la obtención de uniones en dos tipos de materiales cerámicos alto interés tecnológico, como son el nitruro de silicio y el óxido de circonio. El trabajo desarrollado en esta tesis ha consistido, principalmente, en el estudio y caracterización de las interfaces metaVcerámica generadas tras el proceso de unión en estos materiales consigo mismos, o bien con piezas metálicas. En el' caso del ShN4 se utilizó acero inoxidable como lámina de unión. Por o...

Formação de biofilme por Pseudomonas aeruginosa sobre aço inoxidável em contato com leite e seu controle por óleos essenciais

Directory of Open Access Journals (Sweden)

Nádia Nara BATISTA

2014-01-01

Full Text Available Objetivo: Avaliar a ação bacteriostática e bactericida de diferentes óleos essenciais sobre células planctônicas de Pseudomonas aeruginosa ATCC 27853, bem como verificar a ação sanitizante, dos óleos essenciais que apresentarem a menor Concentração Mínima Inibitória (CMI, sobre o biofilme formado por esta espécie, Material e Métodos: A ação bacteriostática foi realizada por meio da determinação das CMIs dos óleos de Zingiber officinale, Eugenia caryophyllus, Elettaria cardamomum, Citrus limon e Citrus reticulata v, tangerine, O tempo de morte bacteriana foi determinado utilizando-se as CMIs de cada óleo essencial submetidos a diferentes tempos de contato, O biofilme de P, aeruginosa foi desenvolvido em cupons de aço inoxidável AISI 304 dispostos em placa de Petri contendo leite tratado por Ultra Alta Temperatura (UAT, sendo incubado sob agitação de 70 rpm, a 37 °C/96 horas, Células aderidas foram removidas através de swabs e enumeradas por contagem em placas após submissão a diferentes tratamentos, Resultados: Todos os óleos essenciais apresentaram efeito bacteriostático, se destacando Z, officinale, E, caryophyllus e E, cardamomum, por apresentarem menor CMI, O tempo de morte de P, aeruginosa foi de 10 minutos quando utilizadas soluções a base de E, cardamomum e E, caryophyllus, No entanto, quando testados em biofilme, apenas E, caryophyllus eliminou as células bacterianas viáveis de P, aeruginosa, Conclusão: E, caryophyllus é uma nova alternativa para o controle do biofilme de P, aeruginosa na indústria de alimentos, pois, além de sua alta atividade antimicrobiana, é um composto natural, o que atende as exigências do mercado consumidor.

Helium and its effects on the creep-fatigue behaviour of electron beam welds in the steel AISI-316-L

International Nuclear Information System (INIS)

Paulus, M.

1992-12-01

Within the scope of R and D work for materials development for the NET fusion experiment (Next European Torus) and the International Thermonuclear Experimental Reactor (ITER), the task reported was to examine electron beam welds in the austenitic stainless steel AISI 316 L (NET reference material) for their fatigue behaviour under creep load, and the effects of helium implantation on there mechanical properties. (orig.) [de

Tool life equation for blanking 18-8 stainless steel strips

Directory of Open Access Journals (Sweden)

Faura, F.

1998-08-01

Full Text Available Hereinafter it is presented a model for the behaviour and life of circular blanking tool used in sheet forming processes of 18-8 stainless steel (sheet thickness: 1 mm. Firstly it has analyzed the different studies that have previously delt with this problem. Secondly taking into account recently made experiments, it is proposed a simple formulation to predict tool life with enough reliability. To this purpose it has examined different parameters in the wear process, inferring from these the fundamental parameters that regulate them and about which the different equations have been configurated. Blanking tests were performed using a 20 t press at a speed of 150 strokes/min. Punch materials used in these tests were AISI A2 and AISI D2 with diameters between 1.5 and 10 mm. The blanking tests were performed at a clearance between 5 and 20 % of the work material thickness.

En el presente artículo se presenta un modelo de ecuación de vida de herramientas para punzonado circular de chapa de acero inoxidable 18-8 (1 mm de espesor. Se han analizado inicialmente los diferentes estudios que previamente han abordado este problema. Posteriormente, teniendo en cuenta los experimentos realizados recientemente, se propone una formulación simple para predecir con Habilidad suficiente la vida de la herramienta. Para este propósito se han examinado los diferentes parámetros que afectan al proceso de desgaste, infiriendo a partir de estos, los parámetros fundamentales que lo regulan y sobre los cuales se han configurado las diferentes ecuaciones. Los ensayos fueron realizados en una prensa de 20 t y una velocidad de punzonado de 150 golpes/min. Los materiales de los punzones usados en los ensayos fueron AISI A2 y AISI D2 con diámetros comprendidos entre 1,5 y 10 mm. Los ensayos se realizaron para juegos de corte comprendidos entre un 5 y 20 % del espesor de la chapa.

Recubrimiento de acero con polidopamina

OpenAIRE

Carrasco Rodríguez, Javier

2013-01-01

Se ha obtenido recubrimientos de polidopamina en acero mecánicamente resistentes y con tiempos de obtención relativamente pequeños a través de la polimerización de la dopamina bajo diferentes condiciones.

The effect of residual thermal stresses on the fatigue crack growth of laser-surface-annealed AISI 304 stainless steel Part I: computer simulation

International Nuclear Information System (INIS)

Shiue, R.K.; Chang, C.T.; Young, M.C.; Tsay, L.W.

2004-01-01

The effect of residual thermal stresses on the fatigue crack growth of the laser-surface-annealed AISI 304 stainless steel, especially the effect of stress redistribution ahead of the crack tip was extensively evaluated in the study. Based on the finite element simulation, the longitudinal residual tensile stress field has a width of roughly 20 mm on the laser-irradiated surface and was symmetric with respect to the centerline of the laser-annealed zone (LAZ). Meanwhile, residual compressive stresses distributed over a wide region away from the LAZ. After introducing a notch perpendicular to the LAZ, the distribution of longitudinal residual stresses became unsymmetrical about the centerline of LAZ. High residual compressive stresses exist within a narrow range ahead of notch tip. The improved crack growth resistance of the laser-annealed specimen might be attributed to those induced compressive stresses. As the notch tip passed through the centerline of the LAZ, the residual stress ahead of the notch tip was completely reverted into residual tensile stresses. The existence of unanimous residual tensile stresses ahead of the notch tip was maintained, even if the notch tip extended deeply into the LAZ. Additionally, the presence of the residual tensile stress ahead of the notch tip did not accelerate the fatigue crack growth rate in the compact tension specimen

Influencia del tiempo de nitruración en baño de sales en el comportamiento tribológico de un acero de herramientas AISI H13