WorldWideScience

Sample records for acero api5l x52

  1. Efecto de la imidazolina [IM-NH17] en el proceso de corrosión del acero api5l-x52 en salmueras acidificadas

    OpenAIRE

    Reynaud-Morales, A.G.; Casales-Díaz, M.; Chacón-Nava, J.G.; Martínez-Gómez, L.; Martínez-Villafañe, A.; González-Rodríguez, J.G.

    2009-01-01

    Se estudia la eficiencia de inhibición del compuesto Imidazolina Aminoetil Oleica [IM-NH17]) en la corrosión de un acero API5L-X52 en tres soluciones de salmuera acidificada a pH 3 a una temperatura de 50°C, empleando pruebas de polarización potenciodinámica y mediciones de resistencia de polarización. Bajo las condiciones de prueba, los resultados de curvas de polarización indicaron que el inhibidor se comporta como un inhibidor de tipo mixto. Los resultados de resistencia de polarización li...

  2. Influencia del acabado superficial en la permeación de hidrógeno del acero API 5L-X52

    Directory of Open Access Journals (Sweden)

    Réquiz, R.

    2004-02-01

    Full Text Available The influence of surface roughness on the corrosion and hydrogen permeation behaviour was evaluated on a type API 5L-X52 steel in deaerated 0.1 M Na2SO4 at pH=2. Potentiodynamic polarization curves were employed to determine the electrochemical behaviour of the steel, while the Devanathan-Stachurski technique was used to estimate the hydrogen permeation rate. Additionally, the surface roughness profiles were obtained in order to correlate the changes in the hydrogen permeation rate with different metal surface finishings. The obtained results clearly demonstrate that when the roughness parameters have larger values, the cathodic current of hydrogen evolution increases while the hydrogen entry rate decreases. This effect can be attributed to the microstructural defects induced at the steel surface, such as dislocations, which increase the catalytic activity of the atomic hydrogen favouring its recombination. Also, these defects could allow the atomic hydrogen to remain adsorbed on the steel surface. Both effects could hinder the hydrogen diffusion into the metal since the possibility for this atom of becoming absorbed has been reduced

    En el presente trabajo de investigación se evalúa la influencia del acabado superficial, tanto en la corrosión generalizada como en la permeación de hidrógeno del acero API 5L-X52 en solución de Na2SO4 0,1M, a pH=2. El comportamiento electroquímico del acero se estudió mediante las curvas de polarización potenciodinámicas, mientras que la susceptibilidad al daño por hidrógeno se evaluó mediante la técnica de permeación de Devanathan- Stachurski. Además, se determinaron los parámetros de rugosidad a las muestras de acero con diferentes acabados superficiales, para luego correlacionarlos con los cambios en las corrientes de permeación de hidrógeno. Los resultados obtenidos demuestran, claramente, que, cuando la rugosidad superficial del acero

  3. Hydrogen sulfide corrosion of weld regions in API X52 steel; Corrosion por acido sulfhidrico de las regiones de soldadura en acero API X52

    Energy Technology Data Exchange (ETDEWEB)

    Arenas-Martinez, L.F [Universidad Autonoma de Coahuila, Coahuila (Mexico)]. E-mail: fernando.arenas@uadec.edu.mx; Garcia-Cerecero, G. [Corporacion Mexicana de Investigacion en Materiales S.A. de C.V., Saltillo, Coahuila (Mexico)

    2012-10-15

    The corrosion behavior of gas metal arc welding (GMAW) regions has been studied using potentiodynamic polarization and polarization resistance (LPR) techniques. Experiments were conducted in hydrogen sulfide (H{sub 2}S)-containing brine and in H{sub 2}S-free brine. Welds were made on API 5L X52 steel. Due to differences in their microstructure, chemical composition and residual stress level, weld regions exhibited different responses under H{sub 2}S corrosion. Base metal exhibited the highest corrosion rate (CR) and the most cathodic corrosion potential. [Spanish] Se estudio el comportamiento ante la corrosion de las regiones de soldadura de un cordon realizado por arco metalico con gas (GMAW) sobre un acero grado API X52 mediante las tecnicas de polarizacion potencio dinamica y resistencia a la polarizacion (LPR). Los experimentos se realizaron utilizando salmuera con 300 ppm de acido sulfhidrico (H{sub 2}S) y salmuera libre de H{sub 2}S como electrolitos. Debido a las diferencias en su microestructura, composicion quimica y el nivel de esfuerzos residuales, las regiones de soldadura mostraron diferentes respuestas a la corrosion por H{sub 2}S. El metal base exhibio la velocidad de corrosion (VC) mas alta y el potencial de corrosion mas catodico.

  4. Estudio del daño por hidrógeno en uniones soldadas de un acero API 5L X52

    Directory of Open Access Journals (Sweden)

    Réquiz, R.

    2008-04-01

    Full Text Available The main objective of the present investigation was to study the susceptibility to hydrogen damage on a type API 5L X52 steel welded by electrical resistance. Several techniques, such as hydrogen permeation and cathodic charging were used. The metallic material was characterized using SEM and TEM. The base metal microstructure was very similar to that one corresponding to the welded area. This microstructure was mainly comprised by ferrite and perlite, differing only in the grain size. Therefore, the susceptibility to hydrogen damage was similar in both cases. It is worth mentioning that the welded area has very small dimensions. Indeed, the fusion zone is only 5 mm wide while the heat affected zone is 1 mm wide. The hydrogen damage observed was mainly in the form of blisters, which were associated to the presence of aluminum rich inclusions. Also, it was noticed partial inclusion dissolution and some matrix attack adjacent to the inclusions.

    En la presente investigación se estudió la susceptibilidad al daño por hidrógeno en un acero API 5L X52 soldado por resistencia eléctrica. Para ello, se emplearon técnicas de permeación y de carga catódica de hidrógeno. El material fue caracterizado mediante microscopía electrónica de barrido y de transmisión. La susceptibilidad al daño por hidrógeno fue similar tanto en el metal base como en el cordón de soldadura. Este comportamiento se vincula a la microestructura homogénea constituida por perlita y ferrita, que presentan ambos, aun cuando existen diferencias en el tamaño de grano. El cordón de soldadura tenía dimensiones muy pequeñas, donde la zona de fusión y la afectada por el calor poseen espesores de 5 mm y 1 mm, respectivamente. El daño inducido por hidrógeno se presentó en forma de ampollas en la superficie del material, asociado, principalmente, a la presencia de inclusiones globulares y semiglobulares ricas en aluminio. Además, se manifestó una disoluci

  5. Influencia del precalentamiento en las propiedades de uniones soldadas de acero API 5L-X80 soldadas con alambre tubular autoprotegido

    Directory of Open Access Journals (Sweden)

    Cooper, R.

    2004-08-01

    Full Text Available The present work refers to the characterization of API 5L-X80 pipeline joints welded with self-shielded flux cored wire. This process was evaluated under preheating conditions, with an uniform and steady heat input. All joints were welded in flat position (IG, with the pipe turning and the torch still. Tube dimensions were 762 mm in external diameter and 16 mm in thickness. Welds were applied on single V-groove, with six weld beads, along with three levels of preheating temperatures (room temperature, 100 °C, 160 °C. These temperatures were maintained as interpass temperature. The filler metal E71T8-K6 with mechanical properties different from parent metal was used in undermatched conditions. The weld characterization is presented according to the mechanical test results of tensile strength, hardness and impact test. The mechanical tests were conducted according to API 1104, AWS and ASTM standards. API 1104 and API 51 were used as screening criteria. According to the results obtained, it was possible to remark that it is appropriate to weld API 5L-X80 steel ducts with Self-shielded Flux Cored wires, in conformance to the API standards and no preheat temperature is necessary.

    Este trabajo presenta un estudio sobre la caracterización de las propiedades mecánicas de uniones soldadas con alambre tubular autoprotegido, de acero API 5L-X80. En este sentido, se evalúa la influencia de la temperatura de precalentamiento, manteniendo el aporte de calor uniforme. Todas las uniones soldadas se realizaron en la posición plana (IG, con la antorcha fíja y la tubería girando. Se utilizó un tubo de 762 mm de diámetro exterior y 16 mm de espesor. Las soldaduras se aplicaron sobre una unión de tope con bisel en V simple, utilizando 6 pasadas, con tres niveles de temperatura de precalentamiento (ambiente, 100 °C y 160 °C. Estas temperaturas se mantuvieron como temperatura entre pasadas. El metal de aporte, del tipo E71T8-K6, se utilizó en la

  6. Efecto de la corrosión por h 2 so 4 en la difusividad térmica de acero api5l-x52.

    Directory of Open Access Journals (Sweden)

    Gabriel Peña-Rodríguez

    2004-01-01

    Full Text Available In this work present a study of the effect of the H2SO4 corrosion to constant pH of 1.4 in the thermal diffusivity of API5L-X52 pipeline steel. The samples were exposed by 3, 6, 9, 12 and 15 days to the corrosive solution, in an atmosphere with relative average humidity of 57.16% and temperature of 23.6°C. The thermal diffusivity measure was carried out using the photoacoustic technique in a heat transmission configuration. Our results show a decrease of the thermal diffusivity ( a with the corrosion time, presenting a behavior that is adjusted to a logistical curve of type decreasing with a saturation limit of 52% of a initial value.

  7. Corrosion of API 5L B and X52 in crude oil/water/gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Perdomo, J J; Gonzalez, J J; Viloria, A; De Veer, H; De Abreu, Y

    2000-02-01

    Laboratory and field tests were conducted to evaluate the corrosion behavior of API 5L grade B and X52 steels using Furrial's crude oil in the presence of water and gas containing carbon dioxide (CO{sub 2}) and hydrogen sulfide (H{sub 2}S). The results suggest that the corrosiveness of this crude oil/water/gas mixture is not detrimental to either steel. However, pitting corrosion was observed. The low general corrosion rates measured were attributed to the natural inhibiting properties of the crude oil.

  8. Evaluación de la susceptibilidad a la corrosión por picado del acero API 5L x42 expuesto a un ambiente con cloruros y CO2 mediante la técnica de ruido electroquímico

    Directory of Open Access Journals (Sweden)

    Rodríguez-Vanegas, N.

    2011-10-01

    Full Text Available The concentration of chloride ions and the partial pressure of CO2 play an important role in the degradation of low-carbon steels used for the construction of pipelines in oil and gas industry. In order to evaluate the susceptibility of carbon steel API 5L X42 to pitting corrosion electrochemical noise and linear polarization resistance measurements were carried out in aqueous solutions containing chloride ions and CO2. The concentration of chloride ions was varied between, 10000 and 18000 ppm, and the CO2 partial pressure between 10 psi and 18 psi. Experimental results pointed out that the formation of protective layer, consisting mainly of FeCO 3, depends on the partial pressure of CO2 in the system. Nevertheless, the stability of this layer was considerably affected by increasing the concentration of chloride ions causing that localized corrosion has taken place in some areas of the surface of API 5L X42, which were detected by electrochemical noise echnique.La concentración de iones cloruro y la presión parcial de CO2, tienen un papel importante en el proceso de degradación de los aceros de bajo carbono empleados en la construcción de líneas de transporte en industrias petroleras. Con el fin de evaluar la susceptibilidad del acero al carbono API 5L X42 a la corrosión por picado, se realizaron medidas de ruido electroquímico y resistencia a la polarización lineal en soluciones acuosas de iones cloruro con concentraciones entre 10.000 y 18.000 ppm, variando la presión parcial de CO2 entre 10 psi y 18 psi. Los resultados indican que la formación de una capa protectora, constituida principalmente por FeCO3, depende de la presión parcial de CO2 del sistema. No obstante, la estabilidad de dicha capa es afectada significativamente por el aumento de la concentración de iones cloruro, que producen fenómenos de corrosión localizada en algunas áreas de la superficie del acero API 5L X42, los cuales fueron detectados por la técnica de

  9. Corrosion of API 5L B and X52 in crude oil/water/gas mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Perdomo, J.J.; Gonzalez, J.J.; Viloria, A.; De Veer, H.; De Abreu, Y.

    2000-02-01

    Laboratory and field tests were conducted to evaluate the corrosion behavior of API 5L grade B and X52 steels using Furrial's crude oil in the presence of water and gas containing carbon dioxide (CO{sub 2}) and hydrogen sulfide (H{sub 2}S). The results suggest that the corrosiveness of this crude oil/water/gas mixture is not detrimental to either steel. However, pitting corrosion was observed. The low general corrosion rates measured were attributed to the natural inhibiting properties of the crude oil.

  10. Technological impact in steels degree API 5L X-70 for the manufacture of resistant ducts of 36 inches of diameter to the bitter gas; Impacto tecnologico de aceros grado API 5L X-70 para la fabricacion de ductos de 36 pulgadas de diametro resistentes al gas amargo

    Energy Technology Data Exchange (ETDEWEB)

    Aramburo Perez, G.; Garcia Galan, S.; Perez Campos, R.; Juarez Islas, J.A. [Facultad de Quimica, UNAM, Mexico, D.F. (Mexico)

    2004-03-01

    , cumplen con las propiedades del acero grado API 5L X-70, las cuales son requeridas en los tubos de acero por la industria petrolera.

  11. The influence of surface roughness on the hydrogen permeation of type API 5L-X52 steel; Influencia del acabado superficial en la permeacion de hidrogeno del acero API 5L-X52 steel

    Energy Technology Data Exchange (ETDEWEB)

    Requiz, R; Vera, N; Camero, S

    2004-07-01

    The influence of surface reoughness on the corrosion and hydrogen permeation behaviour was evaluated on a type API 5L-52 steel in dearated 0.1M NaSO{sub 4} at pH=2. Potentiodynamic polarization curves were emplyed to determine the electrochemical behaviour of the steel, while the Devanathan-Stachurski technique was used to estimate the hydrogen permeation rate. Additionally, the surface roughness profiles were obtained in order to correlate the changes in the hydrogen perkeation rate with different metal surface finishings. The obtained results clearly demonstrate that when the roughness parameters have larger values, the cathodic current of hydrogen evolution increases while the hydrogen entry rate decreases. This effect can be attributed to the microstructural defects induced at the steel surface, such as dislocations, which increase the catalytic activity of the atomic hydrogen favouring its recombination. Also, these defects could allow the atomic hydrogen to remain adsorbed on the steel surface. Both effects could hinder the hydrogen diffusion into the metal since the possibility for this atom of becoming absorbed has been reduced. (Author) 16 refs.

  12. Induction bending of API 5L X80 pipes; Curvamento a quente de tubos API 5L X80

    Energy Technology Data Exchange (ETDEWEB)

    Batista, Gilmar Z. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)]. E-mail: g.zacca@petrobras.com.br; Naschpitz, Leonardo [Primus Processamento de Tubos S.A. - PROTUBO, Campo Grande, RJ (Brazil)]. E-mail: naschpitz@protubo.com.br

    2005-07-01

    The present work is a part of an extensive program to make possible the application of API 5L X80 in pipeline construction in Brazil. At this stage, the effect of the induction bending process on the microstructure and mechanical properties of the pipe is presented. For this study an API 5L X80 pipe, made by the UOE process, is used. The pipe was manufactured from a plate produced by thermo-mechanically controlled rolling without accelerated cooling. The pipe bending was carried out applying a local induction heating following by water quenching. The bend section, outer and inner curvature regions, of the pipe bend were evaluated and compared with the original pipe. The longitudinal weld and transition zones were not evaluated at this stage. Dimensional analyses, microstructural evaluation, Charpy-V impact tests, and tensile tests were performed. A significant microstructural change was verified in the bend area. The yield strength of the pipe bend was found to be lower than original pipe and standard requirements. Other tensile properties and impact properties are compatible with API 5L X80 requirements. (author)

  13. Corrosive effect of oil's accompanying water polluted with H2S over steel (API 5L X-52)

    International Nuclear Information System (INIS)

    Cueli Corugedo, Alexander; Adames Montero, Yosmari; Rivera Beltran, Yischy; Davis Harriet, Juan

    2013-01-01

    The corrosion from the steel to the carbon in the sale oil pipage conduction, is a serious problem, due to the material and economical looses they cause, damaging even in some cases the productive field. The purpose of this study is to determine the aggressiveness of the oil's water layer, polluted with H 2 S ( g) , over the steel of pipelines' construction (API 5L X-52), taking into account the temperature variations which take place during the transportation of the oil, using the electrochemical techniques of polarisation resistance (LPR) and electrochemical noise. It is pretended to determine the velocity of steel corrosion in the oil's water layer polluted with H 2 S through electrochemical techniques. It was shown that the temperature increases and the concentration of H 2 S to 500 ppm in the oil's accompanying water emphasizes the corrosion phenomenon experienced by the steel (9, 188 0 mm/year to 70℃).The results of the electrochemical noise spectrums and the values of the localisation ?s index calculated, shown the presence of corrosion on the steel surface (API 5L X-52).This result was complemented through optic Microscopy which permits to corroborate the poor adherence of the sulphur layers deposited on the metal that increase the appearance of events found with the temperature increase and the concentration of H 2 S in the environment studied

  14. Influence of preheating on API 5L-X80 pipeline joint welding with self shielded flux-cored wire; Influencia del precalentamiento en las propiedades de uniones soldadas de acero API 5L-X80 soldadas con alambre tubular autoprotegido

    Energy Technology Data Exchange (ETDEWEB)

    Cooper, R.; Silva, J. H. F.; Trevisan, R. E.

    2004-07-01

    The present work refers to the characterization of API 5L-X80 pipeline joints welded with self-shielded flux cored wire. This process was evaluated under preheating conditions, with an uniform and steady heat input. All joints were welded in flat position (1G), with the pipe turning and the torch still. Tube dimensions were 762 mm in external diameter and 16 mm in thickness. Welds were applied on single V-groove, with six weld beads, along with three levels of preheating temperatures (room temperature, 100 degree centigree, 160 degree centigree). These temperatures were maintained as inter pass temperature. The filler metal E71T8-K6 with mechanical properties different from parent metal was used in under matched conditions. The weld characterization is presented according to the mechanical test results of tensile strength, hardness and impact test. The mechanical tests were conducted according to API 1104, AWS and ASTM standards. API 1104 and API 51 were used as screening criteria. According to the results obtained, it was possible to remark that it is appropriate to weld API 5L-X80 steel ducts with Self-shielded Flux Cored wires, in conformance to the API standards and no preheat temperature is necessary. (Author) 22 refs.

  15. Analysis of 3D Planar Laminations in a Welded Section of API 5L X52 Applying the Finite Element Method

    Directory of Open Access Journals (Sweden)

    Martin. J. Fernández-Cueto

    Full Text Available Abstract The mechanical behavior of API 5L X52 steel with planar type laminations was studied in the present work. Planar laminations were proposed in the base metal (BM, heat affected zone (HAZ and welding bead (WB. Three-dimensional finite element (FE models, kinematic hardening and mechanical properties for BM, HAZ, and WB were activated in the finite element program. The results showed that crack propagation corresponds to the direction of the main stress. For a crack length (2a of 10.01 mm, crack propagation may occur at the right crack tip towards the outer wall of the BM. For 2a of 15.12 mm, crack propagation was located on the right crack tip and propagates to the inner wall. For 2a of 17.12 mm, crack propagation was observed at the left crack tip and propagates to the outer wall in the BM. The results achieved by FEM agree when compared with real laminations in API 5L pipelines.

  16. CORROSION LOCALISEE DES ACIERS API 5L-X52 DE LA LIGNE ASR/MP SOLLICITE EN SOL ALGERIEN

    OpenAIRE

    BENDJEBBOUR, Amina

    2011-01-01

    L'étude porte sur les défaillances par corrosion localisée dans les aciers API de grade X52 de la ligne de pipelines ASR/MP acheminant les produits pétroliers sollicités en sol corrosif après échec des systèmes de protection anticorrosion (AC) à base de liants hydrocarbonés ou encore à base d'un système en multicouche complétée par une protection cathodique.

  17. BEHAVIOUR CORROSION OF API 5L X70 AND API 5L X80 STEELS IN A CO2 MEDIUM BY SURFACE ANALYSIS AND ELECTROCHEMICAL TECHNIQUES

    OpenAIRE

    MILAGROS MABEL GUILLEN NUNEZ

    2006-01-01

    A seleção de materiais para o transporte de óleo e gás não é feita pela sua resistência à corrosão, mas sim pelas suas boas propriedades mecânicas, facilidade de fabricação e baixos custos. Devido às taxas de perda de material, causado pela corrosão interna, existe necessidade em se conhecer o comportamento dos aços de mais alta resistência, utilizados especialmente em gasodutos e oleodutos tais como API 5L X70 e API 5L X80. Um dos elementos responsáveis ...

  18. Comportamiento a la Corrosión del Acero API X70 Soldado por el Proceso de Doble Arco Sumergido Inmerso en Diferentes Medios Corrosivos

    OpenAIRE

    Montes, Omar Francisco; Garcés, Rocío Saldaña; Reyes, Felipe A. Reyes; Robledo, Patricia del Carmen Zambrano; López, Francisco H. Estupiñán; Calderón, Facundo Almeraya

    2016-01-01

    Resumen Los aceros API X70 son aplicados en fabricación y construcción de tuberías para el transporte de hidrocarburos, sin embargo, a un lapso de tiempo se degradan debido al medio ambiente al cual están expuestos; influyendo en la velocidad y tipo de corrosión sobre las superficies del metal base (MB), zona afectada por el calor (ZAC) y zona de fusión (ZF). A fin de conocer y evaluar la susceptibilidad a la corrosión en uniones del acero API X70 sometido a diferentes medios corrosivos, vari...

  19. Construction and assembly of pipelines using API 5L grade X80 tubes - considerations to be observed with high-strength steels; Construcao e montagem de dutos terrestres utilizando tubos API 5L Gr. X80

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Ailton C. de; Rabello, Jose Mauricio B. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2005-07-01

    The use of line pipes API 5L Grade X80, at the point of view of designer allows: reduction of wall thickness and pipe weight or increase of design pressure. In the pipeline construction point of view, the use of line pipes API 5L Grade X80 provide some advantages, however some difficulties must be expected in several stages of the construction and assembly. The implications in cost, productivity, inspection and integrity, with the application of these high resistance steels, complying with PETROBRAS Standard N - 464 Construcao, Montagem e Condicionamento de Dutos Terrestres (Rev. H - 2004 Dec) and the experience consolidated in pipelines construction abroad were presented. At the design stage, a comparison between pipelines designed using API 5L-X70 and API 5L-X80 was carried out approaching the aspects of variation of thickness, pressure design and design factor. An evaluation of the expected gains when choosing API 5L Grade X80 steels were done, regarding reduction of costs and pipe weight. Regarding API 5L-X80 pipe fabrication, the obtained results were reported, proving that this aspect was already overcome, showing the viability of its production in Brazil. Difficulties were detected regarding construction and assembly stage and showing the need of revision of PETROBRAS standard N-464. (author)

  20. Estudo do efeito da tensão sobre a permeação por Hidrogênio em Aços API 5L X60 e API 5L X65

    Directory of Open Access Journals (Sweden)

    Bruno Araújo Araújo

    2017-12-01

    Full Text Available Under operating conditions, the oil and gas transmission pipelines can be subjected to high pressures and, at the same time, suffer the effect of acidic substances in the transported hydrocarbons such as H2S, whose action alone or combined with stresses acting in the structure can cause degradation processes of the mechanical properties of the material. Given the importance of the phenomenon, this work has as main objective the realization of hydrogen electrochemical permeation tests in API 5L X60 and API 5L X65 steels under mechanical loading conditions. A device for performing electrochemical permeation tests of hydrogen in the specimens subjected to stress was used for the tests. Thus, it was possible to observe experimentally the influence of stress on the diffusion properties during the experiment. By applying stress on the order of 20% of the yield strength, it was possible to verify the increase of diffusivity of API 5L X60 steel. Furthermore, there was a strong influence of the stress level of permeability, because a large increase of permeability of API 5L X65 steel. The results indicate that the lattice deformation due to imposed mechanical stress has a great influence on the diffusion properties of materials

  1. Effect of artificial aging on the microstructure of weldment on API 5L X-52 steel pipe

    International Nuclear Information System (INIS)

    Vargas-Arista, B.; Hallen, J.M.; Albiter, A.

    2007-01-01

    The effects of artificial aging on the microstructure in the weldment of an API 5L X-52 steel pipe were studied. Aging was performed at 250 deg. C over a period of 1000 h and values were recorded at every 100 h intervals. Transmission electron microscopy observations showed precipitation strengthening from nearly circular Nb-C containing nanoparticles for the base metal and heat affected zone, and cementite for the weld metal. The largest amount of precipitation in the weldment zone was obtained at 500 h, due to peak-aging, which showed the highest particle density. The weld metal was more susceptible to aging, exhibiting the highest increase in precipitation at 500 h, followed by the heat affected zone. After 500 h, the deterioration in the microstructure was caused by the coarsening of particles due to over-aging. The base metal showed the larger increment in particle size after 900 h of aging accompanied by a bigger decrease in fine particles than in the weld metal

  2. DESGASTE POR ABRASIÓN DEL ACERO API 5L X65 REVESTIDO CON NIOBIO POR ASPERSIÓN TÉRMICA A PLASMA Y CON INCONEL 625 POR SOLDADURA

    Directory of Open Access Journals (Sweden)

    JOSE MATOS

    2012-01-01

    Full Text Available El objetivo de este trabajo fue evaluar y caracterizar el comportamiento mecánico en desgaste del acero API 5L X65, revestido con niobio en comparación al desempeño del revestimiento de la aleación de inconel 625 empleados en la industria de petróleo y gas. El revestimiento de niobio fue obtenido por el proceso de aspersión térmica a plasma de arco no transferido y el revestimiento inconel 625 por soldadura con electrodo revestido. La resistencia al desgaste por abrasión fue evaluada según la norma Petrobras N-2568, en un tribómetro CTER, la rugosidad y el volumen de material desgastado se determinó a través de perfilometría y la dureza de los revestimientos por microscopia Vickers. Los revestimientos obtenidos fueron caracterizados respecto a su morfología por microscopia electrónica de barrido (MEB y microscopía óptica (MO. La mayor dureza del revestimiento con niobio obtenido puede haber contribuido a reducir la tasa de desgaste en comparación con el revestimiento de inconel 625.

  3. “Corrosión Inducida por Bacterias Sulfato Reductoras Termófilas de 60°C en la Unión Soldada del Acero API 5L- X60.”

    OpenAIRE

    Romero Romero, Justo Román

    2012-01-01

    En esta investigación se estudio el efecto de la corrosión inducida por Bacterias Sulfato Reductoras (BSR) termófilas a 60oC en el metal base (MB) y la unión soldada (US) del acero API X-60. Las bacterias sulfato reductoras fueron aisladas en el medio sólido postgate con la técnica de estriado, y fueron resembradas hasta obtener la misma morfología. El medio postgate fue seleccionado entre otros medios de cultivo, por el óptimo crecimiento que presento la BSR. Se preparar...

  4. Effects of Pre-Strains on Failure Assessment Analysis to API 5L X65 Pipeline

    International Nuclear Information System (INIS)

    Baek, Jong Hyun; Kim, Young Pyo; Kim, Woo Sik; Seok, Chang Sung

    2009-01-01

    This paper prescribed the structural integrity of the API 5 L X6 5 pipeline subjected to tensile pre-strain. The effects of pre-strain on the mechanical properties of API 5 L X6 5 pipe were substantially investigated through a variety of the experimental procedures. Axial tensile pre-strain of 1.5, 5 and 10% was applied to plate-type tensile specimens cut from the pipe body prior to mechanical testing. Tensile test revealed that yield strength and tensile strength were increased with increasing tensile pre-strain. The increasing rate of the yield strength owing to the pre-strain is greater than that of the tensile strength. However, the pre-strain up to 5% had a little effect on the decreasing of the fracture toughness. The structural integrity of the API 5 L X6 5 pipeline subjected to large plastic deformation was evaluated through the fitness-for service code.

  5. Development of an API 5 L X 70 coil for the production of API pipes continuously welded by electric resistance; Desenvolvimento de bobina API 5 L X 70 para producao de tubos API soldados continuamente por resistencia eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, Alexandre R; Cavalheiro, Benedito C [CONFAB Tubos S.A., Sao Caetano do Sul, SP (Brazil)

    1998-07-01

    The manufacturing of high strength ERW pipe, which applies the continuous forming process, is known to lead to a relevant economy in a productivity basis. The past few years shown a trend of changing on grade range, from the past X52 to the present X70. The manufacturing of the latter grades for coils are somehow difficult due to the high Bauschinger effect observed on ERW pipes with ferritic-perlitic microstructure, that results in pipes with yield strength much lower than in coils, as on limitations on rolling, where controlled rolling is not applied. In this work, acicular dispersed bainite was searched, in a way to reduce this effect after pipe forming. API 5L X70 coils, from USIMINAS, were processed including an intentional addition of Molybdenum in the range of 0.20%, together with Columbium and Vanadium (added as 0.050% average). (author)

  6. Effect of non-metallic inclusions on hydrogen-induced cracking of API5L X100 steel

    Energy Technology Data Exchange (ETDEWEB)

    Jin, T.Y.; Liu, Z.Y.; Cheng, Y.F. [Department of Mechanical and Manufacturing Engineering, University of Calgary, Calgary, Alberta (Canada)

    2010-08-15

    In this work, the type, composition and distribution of inclusions contained in an API5L X100 steel were characterized by scanning electron microscopy and energy-dispersive x-ray analysis. A hydrogen-charging at various current densities was used to introduce hydrogen into the steel, and the correlation between HIC and the inclusions was established. The microstructure of the steel consists of a leather-like bainitic ferrite matrix, with martensite/austenite as the second phase particles. At least four types of inclusions are contained in API5L X100 steel, elongated MnS inclusions and spherical Al-, Si- and Ca-Al-O-S-enriched inclusions. In particular, the majority of inclusions in the steel are Al-enriched. Upon hydrogen-charging, hydrogen blisters and HIC could be caused in the steel in the absence of external stress. The cracks are primarily associated with the Al- and Si-enriched inclusions, rather than the elongated MnS inclusion. The critical amount of hydrogen resulting in HIC of the tested API5L X100 steel is determined to be 3.24 ppm under condition in this work. (author)

  7. Comportamiento a la Corrosión del Acero API X70 Soldado por el Proceso de Doble Arco Sumergido Inmerso en Diferentes Medios Corrosivos

    Directory of Open Access Journals (Sweden)

    Omar Francisco Montes

    Full Text Available Resumen Los aceros API X70 son aplicados en fabricación y construcción de tuberías para el transporte de hidrocarburos, sin embargo, a un lapso de tiempo se degradan debido al medio ambiente al cual están expuestos; influyendo en la velocidad y tipo de corrosión sobre las superficies del metal base (MB, zona afectada por el calor (ZAC y zona de fusión (ZF. A fin de conocer y evaluar la susceptibilidad a la corrosión en uniones del acero API X70 sometido a diferentes medios corrosivos, varias pruebas se llevaron a cabo por el proceso de soldadura de doble arco sumergido (DSAW, por sus siglas en inglés, las cuales fueron inmersas en diferentes electrolitos: Cloruro de Sodio (NaCl al 3,5% y Agua (H2O a temperatura ambiente para conocer su comportamiento. Se utilizaron técnicas electroquímicas de ruido electroquímico (RE y curvas de polarización cíclica (CPC para obtener velocidad y tipo de corrosión producida en cada una de las muestras analizadas, incluyendo las tres zonas: MB, ZAC y ZF. Además, se utilizaron técnicas de caracterización como microscopía óptica (MO y microscopía electrónica de barrido (MEB para el análisis superficial. La mayoría de las soldaduras presentan corrosión mixta, con mayores velocidades de corrosión en 3,5% de NaCl.

  8. Effect of Normalizing and Solution Heat Treatments in the Microstructure of a Dissimilar Joint Welded Between an API 5L X-52 Steel Pipe and Inconel 625

    OpenAIRE

    Soares, Jefferson Pinto; Terrones, Luis Augusto Hernandez; Paranhos, Ronaldo

    2017-01-01

    Resumo O propósito deste trabalho é comparar as mudanças na microestrutura e na dureza de um tubo de aço API 5L X-52, revestido internamente por soldagem com Inconel 625, após a execução dos tratamentos térmicos de normalização a 1100 °C por 60 min. e resfriamento ao ar, e de solubilização a 1030 °C com aquecimento por indução eletromagnética por 30 s. e resfriamento em água. Foram utilizadas técnicas de microscopia ótica (MO) e eletrônica de varredura (MEV), análise por espectroscopia de ene...

  9. The influence of surface roughness on the hydrogen permeation of type API 5L-X52 steel

    International Nuclear Information System (INIS)

    Requiz, R.; Vera, N.; Camero, S.

    2004-01-01

    The influence of surface roughness on the corrosion and hydrogen permeation behaviour was evaluated on a type API 5L-52 steel in dearated 0.1M NaSO 4 at pH=2. Potentiodynamic polarization curves were employed to determine the electrochemical behaviour of the steel, while the Devanathan-Stachurski technique was used to estimate the hydrogen permeation rate. Additionally, the surface roughness profiles were obtained in order to correlate the changes in the hydrogen perkeation rate with different metal surface finishings. The obtained results clearly demonstrate that when the roughness parameters have larger values, the cathodic current of hydrogen evolution increases while the hydrogen entry rate decreases. This effect can be attributed to the microstructural defects induced at the steel surface, such as dislocations, which increase the catalytic activity of the atomic hydrogen favouring its recombination. Also, these defects could allow the atomic hydrogen to remain adsorbed on the steel surface. Both effects could hinder the hydrogen diffusion into the metal since the possibility for this atom of becoming absorbed has been reduced. (Author) 16 refs

  10. EBSD study of hydrogen-induced cracking in API-5 L-X46 pipeline steel

    International Nuclear Information System (INIS)

    Venegas, V.; Caleyo, F.; Gonzalez, J.L.; Baudin, T.; Hallen, J.M.; Penelle, R.

    2005-01-01

    The spatial distribution of plastic deformation and grain orientation surrounding hydrogen-induced cracks (HIC) is investigated in samples of API-5L-X46 pipeline steel using scanning electron microscopy and electron backscattering diffraction (EBSD). This work shows direct experimental evidence of the influence of microstructure, microtexture and mesotexture on HIC crack path

  11. Influence of preheating on API 5L-X80 pipeline joint welding with self shielded flux-cored wire

    International Nuclear Information System (INIS)

    Cooper, R.; Silva, J. H. F.; Trevisan, R. E.

    2004-01-01

    The present work refers to the characterization of API 5L-X80 pipeline joints welded with self-shielded flux cored wire. This process was evaluated under preheating conditions, with an uniform and steady heat input. All joints were welded in flat position (1G), with the pipe turning and the torch still. Tube dimensions were 762 mm in external diameter and 16 mm in thickness. Welds were applied on single V-groove, with six weld beads, along with three levels of preheating temperatures (room temperature, 100 degree centigree, 160 degree centigree). These temperatures were maintained as inter pass temperature. The filler metal E71T8-K6 with mechanical properties different from parent metal was used in under matched conditions. The weld characterization is presented according to the mechanical test results of tensile strength, hardness and impact test. The mechanical tests were conducted according to API 1104, AWS and ASTM standards. API 1104 and API 51 were used as screening criteria. According to the results obtained, it was possible to remark that it is appropriate to weld API 5L-X80 steel ducts with Self-shielded Flux Cored wires, in conformance to the API standards and no preheat temperature is necessary. (Author) 22 refs

  12. Corrosion study of API 5L x-series pipeline steels in 3.5% NaCl solution under varying conditions

    International Nuclear Information System (INIS)

    Shahid, M.; Qureshi, M.I.; Farooq, M.U.; Khan, M.I.

    2003-01-01

    Pipelines provide convenient and efficient means for mass transportation of variety of fluids, such as oil and gas, over varying distances. In the last two decades or so, pipeline designers focused mainly on the usage of larger sizes and higher operating pressures for achieving higher transportation efficiency. This has been accomplished through the provision of steels with progressive increase in yield strength coupled with good weldability and sufficient toughness to restrict crack propagation. In addition to higher strength and toughness, developing pipeline technologies have required improved resistance to corrosion, which has been tried with specific alloy additions and special control over non-metallic inclusions. Corrosion investigations were carried out on various grades of pipeline steels (API 5L X-46, X-52, X-56, X-60 and X- 70) under varying environmental conditions. This paper describes the results pertaining to corrosion behavior of the steels in 3.5% NaCl solutions in stagnant, turbulent and deaerated conditions. It was found that all grades corrode in this solution and their corrosion potentials and corrosion currents are in close vicinity of each other. Turbulent solutions, however, have shown an increase in corrosion rates whereas deaeration has revealed a relative decrease in aggressivity of the electrolyte. (author)

  13. Estudo do comportamento do aço API 5L X80 quando submetido à soldagem por processo automatizado Study on the behavior of API 5L X80 steel when subjected to automated welding process

    Directory of Open Access Journals (Sweden)

    Siderley Fernandes Albuquerque

    2012-06-01

    Full Text Available No Brasil, a soldagem de tubulações tem sido praticamente de forma manual, entretanto, a utilização de processos de soldagem automatizados têm crescido muito nos últimos anos, contribuindo para o maior controle dos parâmetros de soldagem, e conseqüentemente, a possibilidade de obtenção de juntas soldadas com melhores propriedades mecânicas. A soldagem de tubulações com aço API 5L X80 ainda vem sendo avaliada no Brasil no que diz respeito aos melhores procedimentos, parâmetros e processos de soldagem; a aplicação de processos automatizados nas condições específicas de campo constitui em uma opção ainda incipiente no país por se discutir ainda a relação custo/benefício com a sua implantação. Logo, o objetivo deste trabalho é avaliar o comportamento na ZTA de juntas soldadas do aço API 5L X80 utilizados para transporte de petróleo e gás quando submetidos à soldagem com diferentes parâmetros, procedimentos e processos de soldagem, incluindo o processo automatizado; os resultados indicam além da redução da extensão e do tamanho de grão da ZTA a preservação da estrutura bainítica do metal de base nesta região nas soldagem executadas com processos automatizados.The welding of pipes has been largely manual in Brazil, however, the use of automated welding processes have greatly increased in recent years, contributing to greater control of welding parameters, and consequently, the possibility of obtaining welded joints with better mechanical properties. The welding of pipes of API 5L X80 steel has been evaluated in Brazil considering to best practices, parameters and welding processes; the implementation of automated processes in the specific field conditions is relevant project and innovative design in this area. Therefore, the objective is to evaluate the behavior in the HAZ of the API 5L X80 steel used for transporting oil and gas when subjected to automated welding processes; the results indicated besides the

  14. API 5L X80 PSL2 pipes manufactured by ERW process: TenarisConfab and USIMINAS development; Tubos API 5L X80 PSL2 processados por ERW: desenvolvimento TenarisConfab-Usiminas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Ronaldo C.; Roza, Juliana E.; Kojima, Sergio S. [TenarisConfab, Pindamonhangaba, SP (Brazil); Miranda, Lucio S.; Turani, Leonardo O. [USIMINAS, Ipatinga, MG (Brazil)

    2005-07-01

    The utilization of high strength steels can decrease, both, installation and operation costs of a new pipeline, since the increase of mechanical resistance can reduce the pipe wall thickness and, consequently, the weight of the pipe. For this purpose, the manufacture of electric resistance welding (ERW) pipes is recent, and it comes as an opportunity for gas pipelines, mainly onshore projects. As a function of their larger productivity, ERW pipes are more economically attractive than those produced by seamless and SAW processes. TenarisConfab and USIMINAS, through studies and investments in manufacturing processes, have been working to increase their skills, in order to supply ERW pipes in API 5L X80 PSL2 steel. The steel elaborated by USIMINAS is low C, high Mn, Nb, V and Ti microalloyed, and with additions of Cr and Mo, aiming to produce hot rolled coils with acicular microstructure, achieved as a combination between its chemical composition and higher cooling rates after hot rolling. The results in {phi}18''(457 mm) x 0,469''(11,91 mm) pipes are presented in this article. High toughness values reached at very low temperatures suggest that ERW API 5L X80 PSL2 pipes developed by TenarisConfab and USIMINAS may be an excellent option of choice for onshore projects that request pipes in diameters up to 20''(508 mm) and thickness up to 0,500'' (12,7 mm). (author)

  15. Evaluation of the susceptibility to pitting corrosion of steel api 5L x42 exposed to solutions containing chloride ions and CO{sub 2} by electrochemical noise measurements; Evaluacion de la susceptibilidad a la corrosion por picado del acero api 5l x42 expuesto a un ambiente con cloruros y CO{sub 2} mediante la tecnica de ruido electroquimico

    Energy Technology Data Exchange (ETDEWEB)

    Pena-Ballesteros, D.; Rodriguez-Vanegas, N.; Anteliz, C.; Sarmiento Klapper, H.

    2011-07-01

    The concentration of chloride ions and the partial pressure of CO{sub 2} play an important role in the degradation of low-carbon steels used for the construction of pipelines in oil and gas industry. In order to evaluate the susceptibility of carbon steel API 5L X42 to pitting corrosion electrochemical noise and linear polarization resistance measurements were carried out in aqueous solutions containing chloride ions and CO{sub 2}. The concentration of chloride ions was varied between, 10000 and 18000 ppm, and the CO{sub 2} partial pressure between 10 psi and 18 psi. Experimental results pointed out that the formation of protective layer, consisting mainly of FeCO{sub 3}, depends on the partial pressure of CO{sub 2} in the system. Nevertheless, the stability of this layer was considerably affected by increasing the concentration of chloride ions causing that localized corrosion has taken place in some areas of the surface of API 5L X42, which were detected by electrochemical noise technique. (Author) 10 refs.

  16. Hardness and microstructural characterization of API 5L X70 steel pipes welded by HF/ERW process; Caracterizacao microestrutural e de dureza em tubos de aco API 5L X70 soldados pelo processo HF/ERW

    Energy Technology Data Exchange (ETDEWEB)

    Calcada, Mauricio Vieira; Voorwald, Herman Jacobus Cornelis; Nascimento, Marcelino Pereira do [UNESP, Guaratingueta, SP (Brazil). Faculdade de Engenharia

    2010-07-01

    The materials that stand in the manufacture of steel pipes are called API, that should have, high mechanical resistance, high corrosion resistance, high fatigue resistance, good weldability, and other properties. Thus, the purpose of this project was to evaluate the microstructure and hardness of welded joints by the HF/ERW process of API 5L X70 steel pipes. The microstructural analysis was performed using a surface finish with grit sizes from 220 to 25 {mu}m e polishing with diamond paste from 9 {mu}m to 0.05 {mu}m; the revelation was made with 3% Nital attack. The Vickers hardness was performed across the welded joint by 33 points to indentation. The results were: 80.5 {+-} 3.4% of ferrite and 19.5 {+-} 3.4% of perlite for microanalysis. As for hardness, the values were: 215.69 HV10 for weld line, 218.65 HV10 for ZTA and 218.95 HV10 for base metal. (author)

  17. “Efecto de la Inducción de un Campo Magnético Axial en el Refinamiento de la Microestructura de la Soldadura del Acero para Tubería API-5L-X60 Soldado por Arco Sumergido (AS)”

    OpenAIRE

    López Melgarejo, Alejandro Ulises

    2012-01-01

    En el presente trabajo de tesis, se describe el efecto que tiene la agitación electromagnética producida por un campo magnético externo, debido a la aplicación de una bobina de alambre de cobre de 35.56 cm de diámetro, durante la soldadura de un acero API 5LX60 soldado por arco sumergido. Esta agitación, conlleva al refinamiento de grano de la microestructura columnar del cordón de soldadura, la cual es producida por el alto aporte térmico del mismo proceso. Durante la exper...

  18. Determination of acoustoelastic constant in API-5L-X70 welded pipes; Determinacao da constante acustoelastica de tubos API-5L-X70 com solda

    Energy Technology Data Exchange (ETDEWEB)

    Bittencourt, Marcelo de Siqueira Queiroz; Fonseca, Manoel Antonio da Costa [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil); Oliveira, Carlos Henrique Francisco de [PETROBRAS S.A., Rio de de Janeiro, RJ (Brazil)

    2008-07-01

    To preserve the environment and avoid financial losses resulting from leaks in the transport of natural oil and gas the industry is particularly concerned to ensure the structural integrity of their pipelines. Grounded pipes may be exposed to damages due to unstable soil movement, and in extreme cases, to failure. Then, techniques to assess stress in pipelines are of central importance. The ultrasonic birefringence technique is an efficient method to measure residual stress. It is based on the changing velocity of the shear wave when it crosses a material under stress; this phenomenon is known as acoustoelasticity. The knowledge of the parameter called acoustoelastic constant is necessary to measure stress using this technique. By the mechanical conformation in the manufacture of welded tubes, from rolled plates, different anisotropy degrees are showed around the cross section of these tubes. In this paper it was studied the acoustoelastic constant for the API-5L-X70 steel pipes, with different thicknesses, diameters and manufacturing processes so as to be able to use this technique to stress measurement in pipelines. (author)

  19. Residual stress evaluation by X-Ray diffraction and hole-drilling in an API 5L X70 steel pipe bent by hot induction

    International Nuclear Information System (INIS)

    Ceglias, Rodrigo Braga; Alves, Juciane Maria; Botelho, Ramon Alves; Baeta Junior, Eustaquio de Souza; Santos, Igor Cuzzuol dos; Moraes, Nicki Robbers Darciano Cajueiro de; Oliveira, Rebeca Vieira de; Diniz, Saulo Brinco; Brandao, Luiz Paulo

    2016-01-01

    The API 5L X70 steel is used in high-pressure gas transmission pipelines. Because of this, knowledge of presence of residual stress and their magnitude is important to assess the material integrity in service. For the pipeline manufacturing, tubes need to be curved which is often made using the hot induction bending process. This process can introduce different residual stress depending of tube position. For this research, in order to evaluate the residual stress, was used an API 5L X70 tube that was previously curved by hot induction process. Samples were taken from the extrados, intrados, neutral line and straight section of the curved tube. Residual stresses were studied by two conventional methods: X-Ray Diffraction (XRD) and Hole-Drilling, which are destructive and non-destructive methods, respectively, in order to assess their qualitative responses. Each of these methods presents particular methodologies in sample preparation and material analysis, but also they differ in factors such time consumption and cost of the analysis. The qualitative responses obtained by the two different methods were comparable and satisfactory and pointed out the existence of a compressive residual stress state in steel pipe. (author)

  20. Residual stress evaluation by X-Ray diffraction and hole-drilling in an API 5L X70 steel pipe bent by hot induction

    Energy Technology Data Exchange (ETDEWEB)

    Ceglias, Rodrigo Braga; Alves, Juciane Maria; Botelho, Ramon Alves; Baeta Junior, Eustaquio de Souza; Santos, Igor Cuzzuol dos; Moraes, Nicki Robbers Darciano Cajueiro de; Oliveira, Rebeca Vieira de; Diniz, Saulo Brinco; Brandao, Luiz Paulo, E-mail: brandao@ime.eb.br [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Secao de Engenharia Mecanica e de Materiais

    2016-09-15

    The API 5L X70 steel is used in high-pressure gas transmission pipelines. Because of this, knowledge of presence of residual stress and their magnitude is important to assess the material integrity in service. For the pipeline manufacturing, tubes need to be curved which is often made using the hot induction bending process. This process can introduce different residual stress depending of tube position. For this research, in order to evaluate the residual stress, was used an API 5L X70 tube that was previously curved by hot induction process. Samples were taken from the extrados, intrados, neutral line and straight section of the curved tube. Residual stresses were studied by two conventional methods: X-Ray Diffraction (XRD) and Hole-Drilling, which are destructive and non-destructive methods, respectively, in order to assess their qualitative responses. Each of these methods presents particular methodologies in sample preparation and material analysis, but also they differ in factors such time consumption and cost of the analysis. The qualitative responses obtained by the two different methods were comparable and satisfactory and pointed out the existence of a compressive residual stress state in steel pipe. (author)

  1. Effect of Different Thermomechanical Processes on the Microstructure, Texture, and Mechanical Properties of API 5L X70 Steel

    Science.gov (United States)

    Masoumi, Mohammad; Echeverri, Edwan Anderson Ariza; Silva, Cleiton Carvalho; Béreš, Miloslav; de Abreu, Hamilton Ferreira Gomes

    2018-03-01

    A commercial API 5L X70 steel plate was subjected to different thermomechanical processes to propose a novel thermomechanical rolling path to achieve improved mechanical properties. Scanning electron microscopy, electron backscatter diffraction, and x-ray texture analysis were employed for microstructural characterization. The results showed that strain-free recrystallized {001} ferrite grains that developed at higher rolling temperature could not meet the American Petroleum Institute (API) requirements. Also, refined and work-hardened grains that have formed in the intercritical region with high stored energy do not provide suitable tensile properties. However, fine martensite-austenite constituents dispersed in ferrite matrix with grains having predominantly {111} and {110} orientations parallel to the normal direction that developed under isothermal rolling at 850 °C provided an outstanding combination of tensile strength and ductility.

  2. The Dutch xAPI Experience: xAPI Recipes

    OpenAIRE

    Berg, Alan; Scheffel, Maren; Drachsler, Hendrik; Ternier, Stefaan; Specht, Marcus

    2017-01-01

    We present the collected experiences since 2012 of the Dutch Special Interest Group (SIG) for Learning Analytics in the application of the xAPI standard and best practices around the application of xAPI in various contexts. We present three projects that apply xAPI in very different ways and publish a consistent set of xAPI recipes.

  3. Study of verification and validation of standard welding procedure specifications guidelines for API 5L X-70 grade line pipe welding

    Directory of Open Access Journals (Sweden)

    Qazi H. A. A.

    2017-12-01

    Full Text Available Verification and validation of welding procedure specifications for X-70 grade line pipe welding was performed as per clause 8.2, Annexure B and D of API 5L, 45th Edition to check weld integrity in its future application conditions. Hot rolled coils were imported from China, de-coiling, strip edge milling, three roller bending to from pipe, inside and outside submerged arc welding of pipe, online ultrasonic testing of weld, HAZ and pipe body, cutting at fixed random length of pipe, visual inspection of pipe, Fluoroscopic inspection of pipe, welding procedure qualification test pieces marking at weld portion of the pipe, tensile testing, guided bend testing, CVN Impact testing were performed. Detailed study was conducted to explore possible explanations and variation in mechanical properties, WPS is examined and qualified as per API 5L 45th Edition.

  4. Study of API 5L X70 steel corrosion processes when in contact with some Brazilian soils; Estudo dos processos de corrosao de acos API 5L X70 em contato com alguns dos solos do Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Jesus, Sergio Luis de

    2007-07-01

    Pipelines, fuel storage tanks and other metallic structures are in permanent contact and exposed to different types of soils, of horizons or layers, or of soil aggressiveness. This interaction may cause expressive damages to the environment and to the planned work. Contamination may occur due to leakage of stored products, splitting during transportation, accidents caused by pipelines without extensive maintenance. The result of these accidents could be, among others, some financial losses. In order to recognize the dynamic interactions between metallic surfaces and the environment it is crucial to have preventive actions and to develop better-applied materials. API steel 5L X70 has been used in structures of low and high pressure with high mechanical strength and corrosion and, even so, it is susceptible to etching corrosion since it is in contact with different environments from mangrove regions to industrial environments. The present case evaluated the role of 5L X70 API steel in contact with different soil horizons representative of the Brazilian soil. This investigation correlated chemical species with solute ions in soil solution, secondary and primary phase minerals besides physical and chemical characteristics as pH, electric conductivity, total dissolved solids, among others, to the results of corrosion resistance and ways of corrosion. The evaluation was carried out using x-ray diffractometry, scanning electron microscopy, total reflection x-ray fluorescence, fuel injection flow besides texture and gravimetric analyses to soil characterization and mineralogy, identification of corrosion products, soil solution analyses, evaluation of tested materials and classification of ways and types of corrosion. This was an attempt to integrate the data to a better understanding of the process involving reagents and products. The results showed that different soil horizons such as different types of analyzed soils produce specific etching in metallic structures

  5. Microbial Corrosion of API 5L X-70 Carbon Steel by ATCC 7757 and Consortium of Sulfate-Reducing Bacteria

    OpenAIRE

    Abdullah, Arman; Yahaya, Nordin; Md Noor, Norhazilan; Mohd Rasol, Rosilawati

    2014-01-01

    Various cases of accidents involving microbiology influenced corrosion (MIC) were reported by the oil and gas industry. Sulfate reducing bacteria (SRB) have always been linked to MIC mechanisms as one of the major causes of localized corrosion problems. In this study, SRB colonies were isolated from the soil in suspected areas near the natural gas transmission pipeline in Malaysia. The effects of ATCC 7757 and consortium of isolated SRB upon corrosion on API 5L X-70 carbon steel coupon were i...

  6. Study of API 5L X70 steel corrosion processes when in contact with some Brazilian soils

    International Nuclear Information System (INIS)

    Jesus, Sergio Luis de

    2007-01-01

    Pipelines, fuel storage tanks and other metallic structures are in permanent contact and exposed to different types of soils, of horizons or layers, or of soil aggressiveness. This interaction may cause expressive damages to the environment and to the planned work. Contamination may occur due to leakage of stored products, splitting during transportation, accidents caused by pipelines without extensive maintenance. The result of these accidents could be, among others, some financial losses. In order to recognize the dynamic interactions between metallic surfaces and the environment it is crucial to have preventive actions and to develop better-applied materials. API steel 5L X70 has been used in structures of low and high pressure with high mechanical strength and corrosion and, even so, it is susceptible to etching corrosion since it is in contact with different environments from mangrove regions to industrial environments. The present case evaluated the role of 5L X70 API steel in contact with different soil horizons representative of the Brazilian soil. This investigation correlated chemical species with solute ions in soil solution, secondary and primary phase minerals besides physical and chemical characteristics as pH, electric conductivity, total dissolved solids, among others, to the results of corrosion resistance and ways of corrosion. The evaluation was carried out using x-ray diffractometry, scanning electron microscopy, total reflection x-ray fluorescence, fuel injection flow besides texture and gravimetric analyses to soil characterization and mineralogy, identification of corrosion products, soil solution analyses, evaluation of tested materials and classification of ways and types of corrosion. This was an attempt to integrate the data to a better understanding of the process involving reagents and products. The results showed that different soil horizons such as different types of analyzed soils produce specific etching in metallic structures

  7. Circumferential welding of API X80 steel pipes; Soldagem circunferencial em tubos de aco da classe API X80

    Energy Technology Data Exchange (ETDEWEB)

    Castello Branco, J.F.; Bott, Ivani de S. [Pontificia Univ. Catolica do Rio de Janeiro, RJ (Brazil). Dept. de Ciencia dos Materiais e Metalurgia]. E-mails: joaofcb@uol.com.br; bott@dcmm.puc-rio.br; Fedele, R.A. [Boehler Thyssen Welding, Sao Paulo, SP (Brazil)]. E-mail: engenharia@btwbr.com.br; Souza, Luis Felipe G. de [Centro Federal de Educacao Tecnologica Celso Suckow da Fonseca (CEFET-RJ), Rio de Janeiro, RJ (Brazil). Dept. de Engenharia Industrial Mecanica]. E-mail: lfelipe@cefet-rj.br

    2003-07-01

    The present work is a part of an extensive program for the development of API 5L Gr.X80 grade steel , produced by the well-known UOE production process, for pipeline fabrication. The current stage of this program involves the characterization and performance evaluation/qualification of girth welds produced by Shield Metal Arc Weld (SMAW) under simulated field conditions, with tubes fixed in the horizontal position. Three types of electrodes were utilized for the basic tasks; the root pass, the hot pass and fill and cap passes. The root pass was carried out with an E-6010 electrode to avoid incomplete joint penetration. The hot pass, applied over the root pass, was performed with an E-9010-G electrode. The fill and cap passes were executed with E-10018-G electrodes. The welded joints produced were evaluated according to the API 1104 specification, which requires: side bend, nick- break and tensile tests. Additionally, non-destructive tests, Charpy-V impact tests and metallographic characterization were undertaken. It was verified that this welding procedure, based on three types of electrodes, could produce welded joints in accordance to the API 1104 specification. These results ensure the applicability of the API 5L Gr. X80 steel developed in this research project for use in pipeline construction. (author)

  8. Characterization of Mechanical Properties and Residual Stress in API 5L X80 Steel Welded Joints

    Science.gov (United States)

    de Sousa Lins, Amilton; de Souza, Luís Felipe Guimarães; Fonseca, Maria Cindra

    2018-01-01

    The use of high-strength and low-alloy steels, high design factors and increasingly stringent safety requirements have increased the operating pressure levels and, consequently, the need for further studies to avoid and prevent premature pipe failure. To evaluate the possibility of improving productivity in manual arc welding of this type of steel, this work characterizes the mechanical properties and residual stresses in API 5L X80 steel welded joints using the SMAW and FCAW processes. The residual stresses were analyzed using x-ray diffraction with the sin2 ψ method at the top and root of the welded joints in the longitudinal and transverse directions of the weld bead. The mechanical properties of the welded joints by both processes were characterized in terms of tensile strength, impact toughness and Vickers microhardness in the welded and shot peening conditions. A predominantly compressive residual stress was found, and shot peening increased the tensile strength and impact toughness in both welded joints.

  9. Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

    Energy Technology Data Exchange (ETDEWEB)

    Hernandez-Espejel, A. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Dominguez-Crespo, M.A. [Instituto Politecnico Nacional, CICATA-Unidad Altamira-Tamaulipas, km 14.5, Carretera Tampico-Puerto Industrial Altamira, 89600 Altamira, Tamps (Mexico); Cabrera-Sierra, R. [Instituto Politecnico Nacional, Departamento de Ingenieria Quimica Industrial, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Rodriguez-Meneses, C. [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico); Arce-Estrada, E.M., E-mail: earce@ipn.m [Instituto Politecnico Nacional, Departamento de Ingenieria Metalurgica, IPN-ESIQIE, UPALM Ed. 7, Zacatenco 07738, Mexico, D.F. (Mexico)

    2010-07-15

    Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

  10. Investigations of corrosion films formed on API-X52 pipeline steel in acid sour media

    International Nuclear Information System (INIS)

    Hernandez-Espejel, A.; Dominguez-Crespo, M.A.; Cabrera-Sierra, R.; Rodriguez-Meneses, C.; Arce-Estrada, E.M.

    2010-01-01

    Corrosion films formed by voltammetry using different switching potentials and by immersion on API-X52 pipeline steel in simulated acid sour media (NACE ID182) have been characterized using Scanning Electron Microscopy (SEM), X-ray Diffraction (XRD), Linear Polarization and Electrochemical Impedance Spectroscopy (EIS) techniques. XRD and EDS analysis showed that the films are mainly composed of sulphide compounds (mackinawite, troilite, marcasite and pyrite) as well as iron oxides, as steel damage increases. Across SEM micrographs the corrosion films formed by potentiodynamic and immersion tests are very similar, covering most of the steel. Polarization and EIS results corroborate poor behavior against corrosion.

  11. Effect of Microstructure on Hydrogen Diffusion in Weld and API X52 Pipeline Steel Base Metals under Cathodic Protection

    Directory of Open Access Journals (Sweden)

    R. C. Souza

    2017-01-01

    Full Text Available The aim of this research was to evaluate the influence of microstructure on hydrogen permeation of weld and API X52 base metal under cathodic protection. The microstructures analyzed were of the API X52, as received, quenched, and annealed, and the welded zone. The test was performed in base metal (BM, quenched base metal (QBM, annealed base metal (ABM, and weld metal (WM. Hydrogen permeation flows were evaluated using electrochemical tests in a Devanathan cell. The potentiodynamic polarization curves were carried out to evaluate the corrosion resistance of each microstructure. All tests were carried out in synthetic soil solutions NS4 and NS4 + sodium thiosulfate at 25°C. The sodium thiosulfate was used to simulate sulfate reduction bacteria (SRB. Through polarization, assays established that the microstructure does not influence the corrosion resistance. The permeation tests showed that weld metal had lower hydrogen flow than base metal as received, quenched, and annealed.

  12. Analisa Pengaruh Jenis Elektroda terhadap Laju Korosi pada Pengelasan Pipa API 5L Grade X65 dengan Media Korosi FeCl3

    Directory of Open Access Journals (Sweden)

    Gita Anggaretno

    2012-09-01

    Full Text Available Submarine pipelines (pipa bawah laut di desain untuk transportasi minyak, gas atau air dari lepas pantai menuju receiving point. Baja API 5L Grade X65 merupakan jenis pipa baja yang banyak digunakan pada pipa penyalur gas, air, dan minyak pada pipa bawah laut. Sistem perpipaan ini tidak mungkin terbentuk tanpa adanya proses las. Pengelasan Flux Cored Arc Welding (FCAW  merupakan las yang umum digunakan dalam struktur anjungan lepas pantai. Penelitian ini bertujuan untuk mengetahui pengaruh dari variasi elektroda pengelasan terhadap laju korosi pada pipa API 5L Grade X65. Variasi elektroda yang digunakan adalah elektroda spesifikasi AWS yaitu E7018, E6010 dan E6013. Metode pengujian korosi ini menggunakan bantuan sel tiga elektroda dengan media korosi FeCl3 yang mengacu pada ASTM G48. Dari pengujian ini didapatkan hasil laju korosi pada pengelasan pipa dengan elektroda E7018 adalah 0,53 mmpy, untuk elektroda E6013 adalah 0,69 mmpy, dan untuk E6010 adalah 0,62 mmpy. Perbedaan laju korosi tersebut dipengaruhi oleh tensile strength pada elektroda dan baja yang di las. Selisih kandungan unsur Mangan (Mn pada pipa dan elektroda las juga mempengaruhi perbedaan laju korosi pada pipa. Berdasarkan hasil foto SEM (Scanning Electron Microscope, secara morfologi permukaan weldmetal dengan nilai laju korosi paling tinggi, permukaanya terlihat lebih kasar. Akan tetapi laju korosi hasil las dengan elektroda-elektroda trsebut masih berada pada level yang diijinkan.

  13. Obtaining and analysis of results of fatigue and corrosion-fatigue in steel API 5L X60; Obtencao e analise de resultados de fadiga e corrosao-fadiga em aco API 5L X60

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Bruno Allison [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais; Silva, Antonio Almeida; Santos, Fabio Gualberto Chagas [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2008-07-01

    The corrosion process allied to the fatigue, due to repetitive efforts of several natures, is the main responsible for the damages in pipeline and offshore structures that results in the appears of located faults, and by the way can results in leaks and financial and environmental loss. This phenomenon calls corrosion-fatigue, however, it is very complex, and mainly, in what it concerns the form as this it develops in the structure. The objective of this work is to present some results of experimental fatigue tests and corrosion-fatigue accomplished with specimen that the material originated a pipeline steel API 5L X60. The tests developed in a machine which could test until 12 specimens per time. For test of corrosion-fatigue was used a cell-of-corrosion especially projected, in this way simulated an aggressive environmental condition in a corrosion conditions. With the results of tests, was possible estimate the fatigue limits of the specimen when submitted to the repeated flexing, and compare it with evaluate corrosion-fatigue graphs, that as the literature comes moved down of the curve, in relation to the fatigue curve. (author)

  14. Degradación de la tenacidad al impacto durante el envejecimiento acelerado de soldadura en acero microaleado

    Directory of Open Access Journals (Sweden)

    Vargas-Arista, B.

    2008-12-01

    Full Text Available The effect of accelerated aging on the toughness and fracture of the longitudinal weld metal of an API5L-X52 linepipe steel was evaluated by Charpy V-notch impact test, fracture analysis and transmission electron microscopy. Aging was performed at 250 °C for 100 to 1000 h. The impact results indicated a significant reduction in the fracture energy and impact toughness as a function of aging time, which were achieved by the scanning electron microscope fractographs that showed a decrease in the vol fraction of microvoids by Charpy ductile failure with the aging time, which favored the brittle fracture by transgranular cleavage. The minimum vol fraction of microvoids was reached at 500 h due to the peak-aged. The microstructural analysis indicated the precipitation of transgranular iron nanocarbides in the aged specimens, which was related to the deterioration of toughness and change in the ductile to brittle behavior.

    Se evaluó, mediante el ensayo de impacto Charpy, fractografía y microscopia electrónica de transmisión el efecto del envejecimiento acelerado sobre la tenacidad y fractura de la soldadura en tubería de acero API5L-X52. El envejecimiento se realizó a 250 °C por 1.000 h, con control cada 100 h. Los resultados de impacto indicaron una disminución en la energía de fractura y tenacidad al impacto en función del tiempo del envejecimiento, los cuales se evidenciaron mediante fractografía, por la reducción en la fracción volumétrica de microhuecos por fractura dúctil con el tiempo, favoreciendo la fractura frágil por clivaje transgranular. Sin embargo, a 500 h, se observó la fracción volumétrica mínima debido al pico del envejecimiento. El análisis microestructural evidenció la precipitación de nanocarburos de hierro transgranulares en las muestras envejecidas, la cual se relaciono con la pérdida de tenacidad y cambio en el comportamiento dúctil a frágil, confirmado por fractografía.

  15. Optimización de los Parámetros de Soldadura por Arco Sumergido en Acero HSLA: una Aplicación para Manufactura de Tuberías de Conducción de Hidrocarburos

    OpenAIRE

    Costa,Patricia Sheilla; Reyes-Valdés,Felipe Arturo; Saldaña-Garcés,Rocio; González-González,David Salvador; Delgado-Albavera,Erick Rafael

    2015-01-01

    Resumen El acero HSLA (High Strength Low Alloy) API 5L X70 es utilizado para fabricación de tuberías para transporte de hidrocarburos. La construcción de tuberías de este material involucra alta cantidad de soldadura, donde los parámetros empleados influyen directamente en las estructuras metalúrgicas y en las propiedades mecánicas del mismo cuando soldado. Así, para estudiar el impacto de los parámetros de soldadura por arco sumergido en la resistencia mecánica y dureza de la Zona Afectada p...

  16. Análisis del proceso de corrosión producida en la junta de soldadura de tubería API 5L X70, por el transporte de crudo.

    OpenAIRE

    Cahueñas Cotacachi, Luis Guillermo; Ballesteros Medina, Adolfo Luis

    2012-01-01

    177 hojas : ilustraciones, 29 x 21 cm + CD-ROM 4132 En el presente tema de tesis se analiza la velocidad de corrosión producida por el agua sedimentada de crudo en la zona interna del cordón de soldadura de una tubería API 5L X70 con electrodos E6010 y E7018. Se utiliza el método experimental mediante una cámara de niebla salina desarrollada para simular el medio corrosivo sobre los que se encuentra trabajando la tubería de oleoducto y soldadura, según los estándares internacionales para l...

  17. Study of texture and microstructure evaluation of steel API 5L X70 under various thermomechanical cycles

    Energy Technology Data Exchange (ETDEWEB)

    Masoumi, Mohammad, E-mail: Mohammad@alu.ufc.br; Herculano, Luis Flavio Gaspar; Ferreira Gomes de Abreu, Hamilton

    2015-07-15

    This work studies the influence of different thermomechanical paths on the microstructure and crystallographic texture across the thickness of API 5L X70 pipeline steel manufactured via hot rolling using X-ray diffraction (XRD), scanning electron microscope (SEM), and electron backscattered diffraction (EBSD). The starting materials were controlled hot-rolled at 1000 °C to 44% and 67% reductions and subsequently heat treated with such processes as annealing, water quenching and quench tempering at three different temperatures to evaluate the microstructure and crystallographic texture changes across the thickness. The banded ferrite-pearlite microstructure of the initial material was changed to acicular ferrite, quasi-polygonal ferrite, granular bainite, martensite and retained austenite via different heat treatments. Moreover, different thermomechanical paths induced crystallographic texture variations across the thickness, e.g., {112}//ND, {111}//ND (γ fibre), and {011}//ND fibres dominated on the surface plane in contact with the rolls, whereas {001}//ND and particularly the (001)[1 1 0] texture component developed in the centre plane on which shear deformation has a zero value in this region. In this study, a simple interpretation of texture evolution was analyzed by comparison with the orientation changes that occurred during different rolling schedules and post-treatment processes.

  18. Numerical evaluation of multipass welding temperature field in API 5L X80 steel welded joints

    Directory of Open Access Journals (Sweden)

    J Nóbrega

    2016-10-01

    Full Text Available Many are the metallurgical changes suffered by materials when subjected to welding thermal cycle, promoting a considerable influence on the welded structures thermo mechanical properties. In project phase, one alternative for evaluating the welding cycle variable, would be the employment of computational methods through simulation. So, this paper presents an evaluation of the temperature field in a multipass welding of API 5L X80 steel used for oil and gas transportation, using the ABAQUS ® software, based on Finite Elements Method (FEM. During the simulation complex phenomena are considerable including: Variation in physical and mechanical properties of materials as a function of temperature, welding speed and the different mechanisms of heat exchange with the environment (convection and radiation were used. These considerations allow a more robust mathematical modeling for the welding process. An analytical heat source proposed by Goldak, to model the heat input in order to characterize the multipass welding through the GTAW (Gas Tungsten Arc Welding process on root and the SMAW (Shielded Metal Arc Welding process for the filling passes were used. So, it was possible to evaluate the effect of each welding pass on the welded joint temperature field, through the temperature peaks and cooling rates values during the welding process.

  19. Efeito dos Tratamentos Térmicos de Normalização e de Solubilização na Microestrutura de uma Junta Dissimilar Soldada entre um Tubo de Aço API 5L X-52 e o Inconel 625

    Directory of Open Access Journals (Sweden)

    Jefferson Pinto Soares

    2017-12-01

    Full Text Available Resumo O propósito deste trabalho é comparar as mudanças na microestrutura e na dureza de um tubo de aço API 5L X-52, revestido internamente por soldagem com Inconel 625, após a execução dos tratamentos térmicos de normalização a 1100 °C por 60 min. e resfriamento ao ar, e de solubilização a 1030 °C com aquecimento por indução eletromagnética por 30 s. e resfriamento em água. Foram utilizadas técnicas de microscopia ótica (MO e eletrônica de varredura (MEV, análise por espectroscopia de energia dispersiva (EDS e dureza Vickers. Na condição como soldada, o metal de base (MB teve na zona termicamente afetada (ZTA a formação de zona de grãos grosseiros (ZGG com dureza média de 234 HV. A zona parcialmente diluída (ZPD se apresentou clara, sem contornos de grãos, com alto teor de ferro e dureza média de 370 HV, indicando ser constituída de martensita. No revestimento, a microestrutura é austenítica dendrítica com formação de carbetos de Nb e indícios da presença da fase Laves, com dureza média de 287 HV em suas camadas. Na condição após normalização, a ZTA foi suprimida e houve refino na microestrutura do MB; a ZPD foi mantida com sua morfologia original, porém com redução de cerca de 15% em sua dureza; no revestimento, a microestrutura tornou-se granular, com indício da dissolução da fase Laves e redução de sua dureza de cerca de 26%. Na condição após solubilização, a ZTA do MB foi eliminada, a ZPD manteve sua morfologia e microestrutura original, mas reduziu sua dureza em cerca de 30%; no revestimento, a microestrutura e precipitados foram mantidos, mas houve uma redução da dureza em cerca de 20%. Por fim, este trabalho conclui que ambos os tratamentos térmicos foram considerados benéficos às propriedades do tubo de aço API 5L X-52 revestido internamente com Inconel 625. Promoveram a homogeneização da microestrutura e a redução de dureza na ZTA do MB, significativa redução da

  20. Effect of the welding process on the microstructure and microhardness of API 5L X80 steel welded joint used for oil transportation pipeline; Efeito do processo de soldagem sobre a microestrutura e a microdureza de juntas soldadas de aco API 5L X80 usado em tubulacoes para transporte de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Alves, R.T.P.; Albuquerque, S.F. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Maciel, T.M.; Almeida, D.M.; Santos, M.A.

    2008-07-01

    This study had as objective to evaluate the microstructure and microhardness of API 5L X80 steel welded joints, used for pipelines to transport oil and gas, using the Shield Metal Arc Welding process with pre- heating temperature of 200 deg C and 400 deg C and the AWS E8010G electrode as filler metal. For this, besides the microhardness of the welded joint, the weld metals percentiles of micro-constituents and of columnar and regenerated grains and the medium size and extension of the heat affected zone were evaluated. The percentage of acicular ferrite in weld metal ranged from 13% to 33% which generated values of microhardness from 114 HV to 309 HV. (author)

  1. Microbial Corrosion of API 5L X-70 Carbon Steel by ATCC 7757 and Consortium of Sulfate-Reducing Bacteria

    Directory of Open Access Journals (Sweden)

    Arman Abdullah

    2014-01-01

    Full Text Available Various cases of accidents involving microbiology influenced corrosion (MIC were reported by the oil and gas industry. Sulfate reducing bacteria (SRB have always been linked to MIC mechanisms as one of the major causes of localized corrosion problems. In this study, SRB colonies were isolated from the soil in suspected areas near the natural gas transmission pipeline in Malaysia. The effects of ATCC 7757 and consortium of isolated SRB upon corrosion on API 5L X-70 carbon steel coupon were investigated using a weight loss method, an open circuit potential method (OCP, and a potentiodynamic polarization curves method in anaerobic conditions. Scanning electron microscopy (SEM and energy dispersive X-ray spectroscopy (EDS were then used to determine the corrosion morphology in verifying the SRB activity and corrosion products formation. Results from the study show that the corrosion rate (CR of weight loss method for the isolated SRB is recorded as 0.2017 mm/yr compared to 0.2530 mm/yr for ATCC 7757. The Tafel plot recorded the corrosion rate of 0.3290 mm/yr for Sg. Ular SRB and 0.2500 mm/yr for Desulfovibrio vulgaris. The results showed that the consortia of isolated SRB were of comparable effects and features with the single ATCC 7757 strain.

  2. Comportamiento de Laminaciones Coplanares y No Coplanares en Acero API5L X52 Simuladas mediante Elementos Finitos Behavior of Coplanar and Non-Coplanar Laminations in API5L X52 Steel Simulated by Finite Elements

    OpenAIRE

    Alberto Servin; Jorge L González; Alfredo Morales

    2009-01-01

    Se determina el comportamiento mecánico de laminaciones simples y escalonadas modeladas por elementos finitos en condiciones no lineales de esfuerzo-deformación, para comprender la secuencia de la interacción de los campos de esfuerzos en los extremos de la grietas. Se estableció una matriz de simulación variando la extensión circunferencial de las laminaciones, con espesor del tubo de 610mm de diámetro, con separación vertical y horizontal para el caso de laminaciones escalonadas. Se determi...

  3. Characterisation of weldment hardness, impact energy and microstructure in API X65 steel

    International Nuclear Information System (INIS)

    Hashemi, S.H.; Mohammadyani, D.

    2012-01-01

    The variation of microstructure and mechanical properties in various sub-zones of double submerged arc welded line pipe steel of grade API X65 was investigated. Instrumented Charpy V-notch tests and Vickers hardness experiments were conducted on the fusion zone, base metal and heat affected zone of the weld joint in 14.3 mm thick, 1219 mm outside diameter spiral pipeline. The lowest impact energy and the highest hardness level (160J and 218 HV, respectively) were recorded in the fusion zone. The low energy and high hardness characteristics of the seam weld can be attributed to its cast microstructure and the presence of grain boundary phases (such as proeutectoid ferrite), confirmed by standard metallographic observation. Despite this, service requirements set by the API 5L industry code (minimum impact energy of 73J, maximum hard spots of 350 HV) were fulfilled by the tested steel. Highlights: ► Experimental study of API X65 steel microstructure. ► Analysis of the relationship between X65 steel microstructure and hardness. ► Analysis of the relationship between X65 steel microstructure and impact energy. ► Presentation of detailed technical information on DSA welding in spiral pipes.

  4. Corrosion resistance of ERW (Electric Resistance Welded) seam welds as compared to metal base in API 5L steel pipes

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez Velasquez, Jorge L.; Godinez Salcedo, Jesus G.; Lopez Fajardo, Pedro [Instituto Politecnico Nacional (IPN), Mexico D.F. (Mexico). Escuela Superior de Ingenieria Quimica e Industrias Extractivas (ESIQIE). Dept. de Ingenieria Metalurgica

    2009-07-01

    The corrosion resistance of ERW seam welds and the base metal in API 5L X70 steel pipes was evaluated by Tafel tests. The procedure was according to ASTM G3 standard. The study was completed with metallographic and chemical characterization of the tested zones, that is, the welded zone and the base metal away of the weld. All tests were made on the internal surface of the pipe in order to assess the internal corrosion of an in-service pipeline made of the API 5L X70 steel. The test solution was acid brine prepared according to NACE Publications 1D182 and 1D196. The results showed that the ERW seam weld corrodes as much as three times faster than the base material. This behavior is attributed to a more heterogeneous microstructure with higher internal energy in the ERW seam weld zone, as compared to the base metal, which is basically a ferrite pearlite microstructure in a normalized condition. This result also indicates that pipeline segments made of ERW steel pipe where the seam weld is located near or at the bottom of the pipe are prone to a highly localized attack that may form channels of metal loss if there is water accumulation at the bottom of the pipeline. (author)

  5. Comparative study of the microbiological corrosion among an AISI 304L and an API X65; Estudio comparativo de la corrosion microbiologica entre un AISI 304L y un API X65

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico); Gonzalez F, E. [ITT, Toluca, Estado de Mexico (Mexico)

    2004-07-01

    Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

  6. Comportamiento frente a la corrosión de los aceros inoxidables AISI 430L P/M

    Directory of Open Access Journals (Sweden)

    Corpas, F. A.

    2004-04-01

    Full Text Available In this paper we have studied the resistance to corrosion of the 430L ferritic stainless steels, manufactured by powder metallurgy. We have compared the behaviour of the different series of 430L stainless steels sintered, tempered and annealing, in different corrosive environments. Finally, the microstructure of the steels was determined by means of scanning electron microscopy. The better resistance to corrosion are produced in the steel annealing to 300ºC and 600ºC.

    En este trabajo hemos estudiado la resistencia a la corrosión que presentan los aceros inoxidables ferríticos 430L fabricados por procedimientos pulvimetalúrgicos. Hemos evaluado y comparado distintas series de aceros inoxidables 430L sinterizados, templados y madurados a diferentes temperaturas en atmósfera de nitrógeno, introduciéndolos en varios medios corrosivos de distinta naturaleza. Por último, se determinó la microestructura, mediante microscopía electrónica de barrido. Los mejores valores de resistencia a la corrosión se encuentran para los aceros tratados a 300ºC y 600ºC.

  7. Corrosion rate of API 5L Gr. X60 multipurpose steel pipeline under combined effect of water and crude oil

    Science.gov (United States)

    Miao, Jian; Wang, Qiang

    2016-09-01

    Multipurpose pipeline is often seriously corroded during its service life, and the phenomenon is more prominent once the transportation medium is changed. Electrochemical polarization curves and impedance spectroscopy of the API 5L Gr. X60 steel pipeline's corrosion process in sedimentary water with different ion types and their concentrations have been studied in this work. The results showed that the corrosion rates were found to be 0.00418 and 0.00232 mm/a for pure water and crude oil, respectively. However, for the mixtures of water and crude oil (with water content increased from 0.2 vol% to 10 vol%), the corrosion rate increased consistently and reached a maximum value of 0.15557 mm/a for 10 vol% water in crude oil. The effect of the concentration of various ions, namely, chloride, bicarbonate and sulfate in (oil/water) mixtures on the corrosion rate was characterized by weight-loss method. The results showed that with increasing the ions' concentrations, the corresponding exchange current density increased significantly. The results were further supported by the observations of corrosion morphology using scanning electron microscopy and are helpful in devising guidelines which would help in reducing corrosion in multipurpose transport pipelines involving a change of transported medium during their service life.

  8. Study of sulphate-reducing bacteria corrosion in the weld joint for API X-70 steel

    Directory of Open Access Journals (Sweden)

    Flores, J. E.

    2012-10-01

    Full Text Available The corrosion behavior originated by sulfate-reducing bacteria (SRB was studied in two regions of welded API X-70 steel pipeline. The studies were focused on base material (BM and heat affected zone (HAZ, from the internal region of the pipe. SRB were extracted from oil and grown in a Postgate medium. Corrosion was evaluated at 60 °C for times between 5 and 64 days. Potentiodynamic polarization curves, obtained by electrochemical techniques, indicated surface activation at short times. Structural and morphological characterizations were carried out by scanning electron microscopy (SEM and optical microscopy (OM. H2S concentration and pH were also measured. Results showed an important increase in the corrosion damage up to 20 days, influenced by the SRB activity, which lead to a maximum of H2S (pH minimum. It was found a localized corrosion attack in the HAZ in a higher quantity compared to BM; and the formation of a thin film on the steel surface, originated by corrosion products and bacterial activity.

    El comportamiento ante la corrosión, originada por bacterias sulfato-reductoras (SRB, fue estudiado en dos regiones de un tubo de acero soldado API X-70. Los estudios se enfocaron en el material base (BM y la zona afectada térmicamente (HAZ, en la parte interna del tubo. Las SRB fueron extraídas del petróleo y cultivadas en un medio Postgate. El comportamiento a la corrosión fue evaluado a una temperatura de 60 °C, por periodos comprendidos entre 5 y 64 días. El análisis de las curvas de polarización potenciodinámicas, obtenidas por técnicas electroquímicas, indicó la activación de la superficie para tiempos cortos. La superficie fue caracterizada estructural y morfológicamente mediante microscopia electrónica de barrido (SEM, así como mediante microscopía óptica (OM. La concentración de H2S y el pH también fueron medidos. Los resultados mostraron un aumento importante de la corrosi

  9. The Effect of Impingement Velocity and Angle Variation on the Erosion Corrosion Performance of API 5L-X65 Carbon Steel in a Flow Loop

    Directory of Open Access Journals (Sweden)

    Ihsan UlHaq Toor

    2018-05-01

    Full Text Available Erosion corrosion performance of API 5L-X65 carbon steel was investigated at three different impingement velocities (3, 6 & 12 m/s, five different angles (15, 30, 45, 60, & 90°, and with/without solid particles (average particle size of 314 µm. The experiments were conducted in 0.2 M NaCl solution at room temperature for a duration of 24 h and the results showed that the maximum erosion corrosion rate was observed at 45° irrespective of the velocity. The highest erosion corrosion rate at 45° was due to the balance between the shear and normal impact stress at this angle. Ploughing, deep craters, and micro-forging/plastic deformation were found to be the main erosion corrosion mechanisms. The maximum wear scar depth measured using optical profilometery was found to be 51 µm (average at an impingement angle of 45°.

  10. Comparative study of the microbiological corrosion among an AISI 304L and an API X65

    International Nuclear Information System (INIS)

    Diaz S, A.; Arganis J, C.; Luna C, P.; Carapia M, L.; Gonzalez F, E.

    2004-01-01

    Metallic samples of AISI 304L sensitized and API X65, were subjected to the action of an inoculated media with reductive sulphate microorganisms (SBR), carrying out electrochemical evaluations by means of the techniques of Polarization Resistance (RP), Tafel extrapolation (ET) and Electrochemical Noise (RE). The generated information was complemented with the analysis and diagnostic of the present damage in the surfaces exposed in both metals. The used electrochemical techniques allow to determine the corrosion velocities associated to each system, establishing that the uniform corrosion is not affected by the effect of the microorganisms; however, electrochemical noise, evidenced the formation of stings associated to the presence of bacteria. (Author)

  11. Análisis de soldabilidad de aceros inoxidables con aceros de medio y bajo carbono por SMAW

    Directory of Open Access Journals (Sweden)

    José Luddey Marulanda Arevalo

    2013-12-01

    Full Text Available Se presenta un estudio de la soldabilidad de aceros inoxidables austeníticos AISI 304 y AISI 316 con aceros de bajo y medio carbono AISI 1020 – AISI 1045, empleando como materiales de aporte los electrodos EutecTrode® 52 NG, 54 NG y 57 NG, mediante el proceso de arco eléctrico con electrodo revestido (SMAW. Para analizar la soldabilidad de estos electrodos cuando se realiza la unión de aceros inoxidables con aceros al carbono, se practicaron pruebas metalográficas y ensayos mecánicos de dureza, doblez y tracción, con el fin de observar el comportamiento tanto de la zona afectada térmicamente como del cordón de soldadura, a partir del cambio en las propiedades mecánicas y metalúrgicas en las diferentes regiones de las uniones soldadas. Durante el proceso de soldadura se siguió una especificación del procedimiento de soldadura (WPS, para que los resultados fueran repetibles, minimizando los problemas de agrietamiento en caliente, agrietamiento en frío, formación de fase sigma y precipitación de carburos.

  12. Mechanical Characteristics of Submerged Arc Weldment in API Gas Pipeline Steel of Grade X65

    International Nuclear Information System (INIS)

    Hashemi, S. H.; Mohammadyani, D.

    2011-01-01

    The mechanical properties of submerged arc weldment (SAW) in gas transportation pipeline steel of grade API X65 (65 ksi yield strength) were investigated. This steel is produced by thermo mechanical control rolled (TMC), and is largely used in Iran gas piping systems and networks. The results from laboratory study on three different regions; i.e. base metal (BM), fusion zone (FZ) and heat affected zone (HAZ) were used to compare weldment mechanical characteristics with those specified by API 5L (revision 2004) standard code. Different laboratory experiments were conducted on test specimens taken from 48 inch outside diameter and 14.3 mm wall thickness gas pipeline. The test results showed a gradient of microstructure and Vickers hardness data from the centerline of FZ towards the unaffected MB. Similarly, lower Charpy absorbed energy (compared to BM) was observed in the FZ impact specimens. Despite this, the API specifications were fulfilled in three tested zones, ensuring pipeline structural integrity under working conditions.

  13. 2-Butyne-1,4-diol as a novel corrosion inhibitor for API X65 steel pipeline in carbonate/bicarbonate solution

    International Nuclear Information System (INIS)

    Sadeghi Meresht, E.; Shahrabi Farahani, T.; Neshati, J.

    2012-01-01

    Highlights: ► Corrosion of API 5L X65 is effectively reduced by the addition of the inhibitor. ► The techniques include weight loss, potentiodynamic polarization, EIS and AFM. ► 2-Butyne-1,4-diol acts as a mixed-type inhibitor. ► The adsorption of 2-butyne-1,4-diol obeys Langmuir adsorption isotherm. - Abstract: The inhibition effects of 2-butyne-1,4-diol on the corrosion susceptibility of grade API 5L X65 steel pipeline in 2 M Na 2 CO 3 /1 M NaHCO 3 solution were studied by electrochemical techniques and weight loss measurements. The results indicated that this inhibitor was a mixed-type inhibitor, with a maximum percentage inhibition efficiency of approximately 92% in the presence of 5 mM inhibitor. Atomic force microscopy revealed that a protective film was formed on the surface of the inhibited sample. The adsorption of the inhibitor was found to conform to the Langmuir isotherm with the standard adsorption free energy of −21.08 kJ mol −1 .

  14. Desarrollo de aceros reforzados con carburos primarios vía metalurgia líquida

    Directory of Open Access Journals (Sweden)

    Agote, I.

    2005-12-01

    Full Text Available The steel reinforcement by means of the addition of primary carbides via liquid metallurgy needs to fulfill two essential requirements to be technically viable: the development of a solid reinforcing product which is appropriate to be mixed with the steel and the optimization of the metallurgic addition of these reinforcing particles into the liquid steel. Besides, the improvement of the reinforced alloy characteristics is directly related to the particles' nature of reinforcing particles, their homogeneous and uniform distribution in the matrix and their size and morphology. The manufacture of these carbides by SHS ('Self propagating High temperature Synthesis' and their addition before steel is poured into moulds allows achieving the above-mentioned conditions.

    Para que el reforzamiento de los aceros con carburos primarios vía metalurgia líquida sea técnicamente viable se requiere del desarrollo de un tipo de producto reforzante sólido, adecuado para su incorporación al acero, así como de la optimización de dicha vía metalúrgica de adición del producto reforzante al material base en estado líquido. Además, la mejora de características de la aleación reforzada es función directa de la naturaleza de las partículas, de su homogénea y uniforme distribución en la matriz y del tamaño y morfología regular de las mismas. Estas condiciones se consiguen cuando las partículas de carburo se elaboran previamente mediante la técnica SHS (selfpropagating high temperature synthesis y se añaden al baño de acero líquido previo a su colada en moldes o lingoteras.

  15. Corrosion of API XL 52 steel in presence of Clostridium celerecrescens

    Energy Technology Data Exchange (ETDEWEB)

    Monroy, O.A. Ramos; Ordaz, N. Ruiz; Ramirez, C. Juarez [Escuela Nacional de Ciencias Biologicas, Instituto Politecnico Nacional, Prolongacion de Carpio y Plan de Ayala, Mexico D. F., C. P. 11340 (Mexico); Gayosso, M.J. Hernandez; Olivares, G. Zavala [Instituto Mexicano del Petroleo, Grupo Corrosion, Eje Central Lazaro Cardenas 152, Col. San Bartolo Atepehuacan, Mexico D. F., C. P. 07730 (Mexico)

    2011-09-15

    During the characterization of sediments formed in pipelines transporting hydrocarbons, the knowledge of the microbiological diversity becomes very interesting, especially when it is related to microbiologically influenced corrosion (MIC). The presence of microorganisms is considered as one of the factors that affect the corrosion processes occurring at the pipeline; therefore, their corrosiveness must be determined. In this way, the identification of new species affecting the MIC processes is still considered relevant. In this work, the effect of Clostridium celerecrescens upon the corrosion of API KL 52 steel was evaluated. This microorganism was isolated and identified from the sediments collected during the inner cleaning procedures of a gas pipeline. The polarization resistance (PR) and electrochemical impedance spectroscopy (EIS) techniques were considered to estimate the microorganism behavior during the corrosion process. The results were complemented with a metal surface analysis, using a scanning electron microscope (SEM). The resistance values induced by the presence of the microorganisms clearly indicated that C. celerecrescens has an effect on the corrosion process occurring at the API XL 52 steel surface. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  16. 2-Butyne-1,4-diol as a novel corrosion inhibitor for API X65 steel pipeline in carbonate/bicarbonate solution

    Energy Technology Data Exchange (ETDEWEB)

    Sadeghi Meresht, E. [Materials Engineering Department, Faculty of Engineering, Tarbiat Modares University, 1411713114, Tehran (Iran, Islamic Republic of); Shahrabi Farahani, T., E-mail: tshahrabi34@modares.ac.ir [Materials Engineering Department, Faculty of Engineering, Tarbiat Modares University, 1411713114, Tehran (Iran, Islamic Republic of); Neshati, J. [Research Institute of Petroleum Industry, RIPI, 1485733111, Tehran (Iran, Islamic Republic of)

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer Corrosion of API 5L X65 is effectively reduced by the addition of the inhibitor. Black-Right-Pointing-Pointer The techniques include weight loss, potentiodynamic polarization, EIS and AFM. Black-Right-Pointing-Pointer 2-Butyne-1,4-diol acts as a mixed-type inhibitor. Black-Right-Pointing-Pointer The adsorption of 2-butyne-1,4-diol obeys Langmuir adsorption isotherm. - Abstract: The inhibition effects of 2-butyne-1,4-diol on the corrosion susceptibility of grade API 5L X65 steel pipeline in 2 M Na{sub 2}CO{sub 3}/1 M NaHCO{sub 3} solution were studied by electrochemical techniques and weight loss measurements. The results indicated that this inhibitor was a mixed-type inhibitor, with a maximum percentage inhibition efficiency of approximately 92% in the presence of 5 mM inhibitor. Atomic force microscopy revealed that a protective film was formed on the surface of the inhibited sample. The adsorption of the inhibitor was found to conform to the Langmuir isotherm with the standard adsorption free energy of -21.08 kJ mol{sup -1}.

  17. “Wrapping” X3DOM around Web Audio API

    Directory of Open Access Journals (Sweden)

    Andreas Stamoulias

    2015-12-01

    Full Text Available Spatial sound has a conceptual role in the Web3D environments, due to highly realism scenes that can provide. Lately the efforts are concentrated on the extension of the X3D/ X3DOM through spatial sound attributes. This paper presents a novel method for the introduction of spatial sound components in the X3DOM framework, based on X3D specification and Web Audio API. The proposed method incorporates the introduction of enhanced sound nodes for X3DOM which are derived by the implementation of the X3D standard components, enriched with accessional features of Web Audio API. Moreover, several examples-scenarios developed for the evaluation of our approach. The implemented examples established the achievability of new registered nodes in X3DOM, for spatial sound characteristics in Web3D virtual worlds.

  18. Tratamiento térmico del acero inoxidable ferrítico AISI 430L sinterizado en atmósfera de N2-H2

    Directory of Open Access Journals (Sweden)

    Ruiz-Prieto, J. M.

    2005-12-01

    Full Text Available In this Work the influence of sintering AISI 430L stainless steel in N2-H2 atmosphere on its properties and microstructure have been studied. The presence of nitrogen in the sintering atmosphere leads to complex nitrides formation the AISI 430L sintered steel microstructure. A subsequent heat treatment was applied to modify this microstructure in order to improve the mechanical properties and corrosion resistance of these ferritic stainless steels.Los aceros inoxidables ferríticos, son aceros que contienen esencialmente cromo (12-30 % junto con níquel y molibdeno en cantidades que, en general, no sobrepasan el 1 % y, en ocasiones, se les adicionan otros elementos como son el aluminio, silicio, titanio o niobio. En el presente trabajo de investigación se ha evaluado la influencia del nitrógeno presente en la atmósfera de sinterización sobre la microestructura y propiedades del acero inoxidable ferrítico AISI 430L. Además, se ha realizado un tratamiento térmico posterior de hipertemple y maduración con el objeto de incrementar las propiedades mecánicas y a corrosión de este acero inoxidable, mediante la modificación microestructural de los nitruros complejos de hierro y cromo precipitados durante la etapa de sinterización.

  19. Ultrasound stress measurements for API X65 pipes; Avaliacao por ultra-som das tensoes impostas em tubo API X-65

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, Raimundo C.; Santos, Ramon Loback Medeiros [TRANSPETRO - PETROBRAS Transporte S.A., Rio de Janeiro, RJ (Brazil); Bittencourt, Marcelo S.Q.; Lamy, Carlos A. [Instituto de Engenharia Nuclear (IEN), Rio de Janeiro, RJ (Brazil); Donato, Guilherme V.P. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2003-07-01

    Risks of damages or even premature collapse of buried pipelines caused by their interaction with geologically unstable soils are well-established phenomena. Therefore, both monitoring and measurements of the actual loads transmitted by the soil to the pipeline are mandatory requirements, and define the necessity of developing new nondestructive techniques capable to carry out through evaluations of these loads in field. The aim of this paper has been placed on the presentation of a cutting-edge ultrasonic technology applied to stress measurements. To accomplish this purpose a series of ultrasonic tests were conducted on tensile specimens extracted from API 5L Grade X-65 steel pipe to determine its acoustic birefringence. The results have evidenced the acoustic birefringence to be a technique sufficiently consistent and, consequently, it shall be considered as a promising tool for the evaluation of the structural integrity of metallic structures in the near future. In addition, it was also observed that the use of this technique allows measuring the residual stress resulting from the pipe manufacturing process. (author)

  20. Avaliação da microestrutura e propriedades mecânicas de metais de solda obtidos por processos de soldagem manual e automatizado utilizado na soldagem de aço API 5L X80 Evaluation of microstructure and mechanical properties of weld metals obtained by manual and automated welding process used in the welding of API 5L X80 steel

    Directory of Open Access Journals (Sweden)

    Siderley Fernandes Albuquerque

    2011-12-01

    Full Text Available O objetivo do trabalho foi avaliar as características da zona termicamente afetada (ZTA e a microestrutura e propriedades mecânicas de metais de solda de juntas soldadas do aço API 5L X80, obtidos para quatro diferentes procedimentos de soldagem utilizando processos manuais e automatizados. Para isto, chapas do referido aço foram soldadas por processo manual ao Arco Elétrico com Eletrodo Revestido (SMAW, utilizando 473 e 673 K como temperaturas de interpasses e o eletrodo celulósico AWS E8010-G como consumível; por processo ao Arco Elétrico com Arame Tubular (FCAW robotizado, utilizando o arame AWS E71T- 1C como metal de adição e argônio com 25%CO2 como gás de proteção; por processo a Arco Elétrico com Eletrodo de Tungstênio (GTAW mecanizado na raiz da solda, usando o arame ER70S-3 e argônio como gás de proteção. As análises microestruturais foram relacionadas com os resultados de ensaios de impacto Charpy nos metais de solda e com os perfis de microdureza Vickers ao longo da junta soldada. Os resultados indicaram maiores percentuais de Ferrita Acicular e maiores valores de resistência ao impacto nos metais de solda e uma menor extensão e granulometria da ZTA, associado ao procedimento de soldagem utilizando processo automatizado com maior velocidade de soldagem.The objective of this work was to evaluate the heat affected zone characteristics and weld metals microstructure and mechanical properties of API 5L X80 steel welded joints, obtained for four different welding procedures using manual and automated processes. For this, plates of this steel were welded by manual Shielded Metal Arc Welding (SMAW process with interpasses temperatures of 473 e 673 K, and using AWS E8010-G electrode as filler metals; robotized Flux Cored Arc Welding (FCAW process, using AWS E71T-1C wire and Ar25%CO2 as consumable and mechanized Gas Tungsten Arc Welding (GTAW process, for the root pass using AWS ER70S-3 and Ar as consumable .The

  1. Fissuração pelo Hidrogênio em um Aço API 5L X70 Soldado com Eletrodos Celulósicos de Diferentes Níveis de Resistência

    Directory of Open Access Journals (Sweden)

    Camila Goes Mattioli

    Full Text Available Resumo Aços classificados segundo a norma do American Petroleum Institute (API enfrentam o problema de trincamento a frio decorrente da soldagem. Neste trabalho foi estudado, por meio do ensaio de implante, o efeito da resistência mecânica do metal de solda sobre a susceptibilidade de um aço API-5L-X70 ao trincamento pelo hidrogênio. As soldas foram realizadas com dispositivo de soldagem por gravidade, usando-se dois eletrodos celulósicos, AWS-E6010 e AWS-E8010. O hidrogênio difusível dos eletrodos foi determinado por cromatografia gasosa. Como resultado do ensaio de implante, observou-se uma tendência maior à fissuração quando foi utilizado o eletrodo AWS-E6010. Isso pode ser relacionado à menor resistência mecânica apresentada pela solda resultante do mesmo e ao fato de o eletrodo ser menos ligado. Assim, o metal de solda pode ter se transformado a temperaturas mais elevadas, o que levou a uma maior migração do hidrogênio para a ZTA. Observou-se, ainda, que mesmo as soldas que não falharam no ensaio apresentaram trincas. Isso pode ser devido às condições de resfriamento do cordão que levaram ao aparecimento ilhas com estruturas frágeis e susceptíveis ao trincamento. Para as menores cargas usadas (0,8.σe, contudo, estas trincas não atingiram um tamanho crítico para a ruptura final do pino sendo ensaiado.

  2. INHIBITION EFFECT OF FLAVONOID EXTRACT OF Euphorbia Guyoniana ON THE CORROSION OF MILD STEEL IN H2SO4 MEDIUM

    OpenAIRE

    S. Chihi; N. Gherraf; B. Alabed; S. Hameurlain

    2009-01-01

    The influence of flavonoids extracts of three parts of Euphorbia Guyoniana towards the corrosion of type API 5L X52 steel in 15% H2SO4 has been evaluated by weight loss method and polarization technique. The results showed that extracts are a good inhibitors for API 5L X52 steel in this medium. The corrosion inhibition efficiency increases on increasing plant extracts concentration. The inhibition is attributed to the adsorption of the surface of the metal. Potentiodynamic polarization result...

  3. BEE VENOM TRAP DESIGN OF APIS MELLIFERA L. AND APIS CERANA F. HONEY BEES

    OpenAIRE

    Budiaman

    2015-01-01

    The nectar and pollen of flowers which are abundance have not been taken into account for any purpose in forest, agriculture and plantation area. Honey bees such as Apis mellifera L. and Apis cerana F. had known as biological pollinators which could converted the flower components to be high economy products in the forms of honey, royal jelly, propolis, bee wax and bee venom. Among the products, bee venom has the best selling value, but the method of it???s optimal production has not been ext...

  4. Pim-2 activates API-5 to inhibit the apoptosis of hepatocellular carcinoma cells through NF-kappaB pathway.

    Science.gov (United States)

    Ren, Ke; Zhang, Wei; Shi, Yujun; Gong, Jianping

    2010-06-01

    Pim-2 is proved to be relevant to the tumorigenesis of hepatocellular carcinoma (HCC), but the mechanism is unclear. We studied the relationship among Pim-2, NF-kappaB and API-5. In our experiment, expression level of the three factors and phosphorylation level of API-5, as well as NF-kappaB activity, were detected in HCC tissues and the nontumorous controls. Then Pim-2 gene was transfected into nontumorous liver cells L02, and Pim-2 SiRNA was transfected into hepatoblastoma cell line HepG2. Parthenolide was added as NF-kappaB inhibitor. The same detections as above were repeated in the cells, along with the apoptosis analysis. We found the levels of Pim-2, NF-kappaB and API-5, as well as NF-kappaB activity, were significantly higher in HCC tissues. Pim-2 level was increased in L02 cells after the transfection of Pim-2 gene, but decreased in HepG2 cells after the transfection of Pim-2 SiRNA. The levels of NF-kappaB and API-5, as well as NF-kappaB activity and API-5 phosphorylation level, were in accordance with Pim-2 level, but could be reversed by Parthenolide. Cell apoptosis rates were negatively correlated with API-5 phosphorylation level. Therefore, we infer that Pim-2 could activate API-5 to inhibit the apoptosis of liver cells, and NF-kappaB is the key regulator.

  5. Fabricación aditiva mediante sinterizado láser de polvos de acero inoxidable martensítico AISI 420

    OpenAIRE

    Vega Nava, Sergio

    2014-01-01

    Busqueda de los parámetros de fabricación adecuados y los tratamientos térmicos a realizar, con el fin de alcanzar durezas de 50 HRC y una adecuada porosidad, en el acero inoxidable AISI 420 obtenido mediante sinterizado láser.

  6. Funcionalización electroquímica y tribológica de películas de quitosano en fosfato tricálcico depositados en acero 316L

    Directory of Open Access Journals (Sweden)

    Alexis Mina Escobar

    2013-12-01

    Full Text Available Se depositaron recubrimientos de fosfato tricálcico-β/quitosano sobre sustratos de acero 316L vía electrodeposición, a una temperatura de 60 °C, aplicando una corriente de 260 mA. Con el fin de estudiar el efecto del contenido de quitosano en la velocidad de corrosión y la respuesta tribológica de los aceros recubiertos, se utilizaron seis concentraciones de quitosano en la mezcla acuosa. Los enlaces químicos presentes en las capas fueron estudiados mediante Espectroscopia de Infrarrojo con Transformada de Fourier (FTIR; la cristalinidad de los depósitos fue examinada mediante difracción de rayos-X (DRX; la resistencia a la corrosión del TCP-β/quitosano depositado sobre los aceros se estudió mediante Espectroscopia de Impedancia Electroquímica (EIS y curvas anódicas Tafel, encontrándose una disminución del 54% en la velocidad de corrosión para la relación 50-50, con respecto a 100% TCP. La respuesta tribológica se analizó mediante pin-on-disc, evidenciando una reducción del 73% en el coeficiente de fricción con mayor concentración de quitosano.

  7. Hyperfine interactions and electric dipole moments in the [16.0]1.5(v = 6), [16.0]3.5(v = 7), and X2Δ(5/2) states of iridium monosilicide, IrSi.

    Science.gov (United States)

    Le, Anh; Steimle, Timothy C; Morse, Michael D; Garcia, Maria A; Cheng, Lan; Stanton, John F

    2013-12-19

    The (6,0)[16.0]1.5-X(2)Δ(5/2) and (7,0)[16.0]3.5-X(2)Δ(5/2) bands of IrSi have been recorded using high-resolution laser-induced fluorescence spectroscopy. The field-free spectra of the (191)IrSi and (193)IrSi isotopologues were modeled to generate a set of fine, magnetic hyperfine, and nuclear quadrupole hyperfine parameters for the X(2)Δ(5/2)(v = 0), [16.0]1.5(v = 6), and [16.0]3.5 (v = 7) states. The observed optical Stark shifts for the (193)IrSi and (191)IrSi isotopologues were analyzed to produce the permanent electric dipole moments, μ(el), of -0.414(6) D and 0.782(6) D for the X(2)Δ(5/2) and [16.0]1.5 (v = 6) states, respectively. Properties of the X(2)Δ(5/2) state computed using relativistic coupled-cluster methods clearly indicate that electron correlation plays an essential role. Specifically, inclusion of correlation changes the sign of the dipole moment and is essential for achieving good accuracy for the nuclear quadrupole coupling parameter eQq0.

  8. Apoptosis inhibitor 5 (API-5; AAC-11; FIF) is upregulated in human carcinomas in vivo.

    Science.gov (United States)

    Koci, Lenka; Chlebova, Katarina; Hyzdalova, Martina; Hofmanova, Jirina; Jira, Miroslav; Kysela, Petr; Kozubik, Alois; Kala, Zdenek; Krejci, Pavel

    2012-04-01

    Apoptosis inhibitor 5 (API-5) is a 55 kDa nuclear protein with potent anti-apoptotic signaling in tumor cells in vitro. In this study, we analyzed the expression of the API-5 protein in vivo in a broad spectrum of human carcinomas, including those of the colon, lung, liver, kidney, pancreas, stomach and esophagus using tumor tissues obtained during tumor resection. The results showed significant upregulation of API-5 expression in biopsies of lung (23%, n=13) and colorectal tumors (33%, n=27) in comparison with biopsies from the adjacent normal tissue. Colon cancer biopsies were used to study the cell populations with an upregulated level of expression of API-5 more closely. Using a magnetic bead-based selection for the epithelial cell marker EpCAM, we purified epithelial cells from the tumor and control tissues and analyzed these cells for API-5 expression by western immunoblotting. We observed that EpCAM-positive tumor cells expressed API-5 in all three colorectal cancer cases tested, in contrast to the control EpCAM-positive and EpCAM-negative cells isolated from the control or tumor tissues. These data suggest that the expression of the API-5 protein is upregulated in tumor epithelial cells and may serve as a prognostic marker in colorectal cancer.

  9. INHIBITION EFFECT OF FLAVONOID EXTRACT OF Euphorbia Guyoniana ON THE CORROSION OF MILD STEEL IN H2SO4 MEDIUM

    Directory of Open Access Journals (Sweden)

    S. Chihi

    2009-08-01

    Full Text Available The influence of flavonoids extracts of three parts of Euphorbia Guyoniana towards the corrosion of type API 5L X52 steel in 15% H2SO4 has been evaluated by weight loss method and polarization technique. The results showed that extracts are a good inhibitors for API 5L X52 steel in this medium. The corrosion inhibition efficiency increases on increasing plant extracts concentration. The inhibition is attributed to the adsorption of the surface of the metal. Potentiodynamic polarization results revealed that the studied inhibitors behave as a mixed type.

  10. Simulación de la precipitación de inclusiones en diferentes etapas del procesamiento del acero líquido

    Directory of Open Access Journals (Sweden)

    Carreño, V.

    1998-05-01

    Full Text Available Steelmaking processes are continuously improved in order to attend the increasing requirements of the cleanness of the liquid metal. At the refining stages, as deoxidation and desulphuration, the formation of inclusions of oxides and sulphides is promoted, which on the other hand, are the most frequent inclusions. In this work a mathematical simulator of the precipitation and chemical composition of non-metallic inclusions at different steps of the steelmaking process is presented. To this purpose, it is assumed that inclusions formed by reoxidation can be simulated by increasing arbitrarily the oxygen levels consumed by the residual elements (aluminium, calcium, etc. and starting the chemical reaction with less powerful deoxidants (silicium and manganese. Accordingly, different operative conditions can be simulated. Numerical predictions are compared with experimental results of industrial trials, as well as results included in the bibliography.

    Los procesos de fabricación de acero se mejoran constantemente en respuesta a las demandas del consumidor que exige un mayor control de limpieza del metal líquido en las diversas etapas de su elaboración. En las etapas de refinación, como son desoxidación y desulfuración, se promueve la formación de inclusiones de óxidos y sulfuros, que por otra parte son las más frecuentes en el acero líquido. En este trabajo se presenta un simulador matemático que predice la precipitación y composición de las inclusiones no metálicas que se encuentran en el acero líquido en diferentes etapas de su procesamiento, asumiendo que las inclusiones formadas por reoxidación también se pueden simular al incrementar arbitrariamente los niveles de oxígeno que deberán consumir los elementos residuales altamente oxidables (Al, Ca, y empezar la reacción con los desoxidantes menores (Si y Mn. De esta manera se simulan diferentes condiciones de operación. Las predicciones numéricas se comparan con los

  11. Ductile failure analysis of defective API X65 pipes based on stress-modified fracture strain criterion

    International Nuclear Information System (INIS)

    Oh, Chang Kyun; Kim, Yun Jae; Baek, Jong Hyun; Kim, Young Pyo; Kim, Woo Sik

    2006-01-01

    A local failure criterion for the API X65 steel is applied to predict ductile failure of full-scale API X65 pipes with simulated corrosion and gouge defects under internal pressure. The local failure criterion is the stress-modified fracture strain for the API X65 steel as a function of the stress triaxiality (defined by the ratio of the hydrostatic stress to the effective stress). Based on detailed FE analyses with the proposed local failure criteria, burst pressures of defective pipes are estimated and compared with experimental data. The predicted burst pressures are in good agreement with experimental data. Noting that an assessment equation against the gouge defect is not yet available, parametric study is performed, from which a simple equation is proposed to predict burst pressure for API X65 pipes with gouge defects

  12. Sodium alginate: A promising biopolymer for corrosion protection of API X60 high strength carbon steel in saline medium.

    Science.gov (United States)

    Obot, I B; Onyeachu, Ikenna B; Kumar, A Madhan

    2017-12-15

    Sodium alginate (SA), a polysaccharide biopolymer, has been studied as an effective inhibitor against the corrosion of API X60 steel in neutral 3.5% NaCl using gravimetric and electrochemical techniques (OCP, EIS and EFM). The inhibition efficiency of the SA increased with concentration but was lower at higher temperature (70°C). Electrochemical measurements showed that the SA shifted the steel corrosion potential to more positive value and reduced the kinetics of corrosion by forming an adsorbed layer which mitigated the steel surface wetting, based on contact angle measurement. SEM-EDAX was used to confirm the inhibition of SA on API X60 steel surfaces. The SA adsorbs on the steel surface through a physisorption mechanism using its carboxylate oxygen according to UV-vis and ATR-IR measurements, respectively. This phenomena result in decreased localized pitting corrosion of the API X60 steel in 3.5% NaCl solution. Theoretical results using quantum chemical calculations and Monte Carlo simulations provide further atomic level insights into the interaction of SA with steel surface. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Evaluación de un procedimiento de soldadura para el AISI 4130 sin PWHT bajo normas API 6A y ASME Sección IX

    OpenAIRE

    Naranjo, Carlos; Sánchez, Xavier; Morales, Juan

    2014-01-01

    Resumen— Debido a la complejidad de realizar postcalentamiento en campo necesario para garantizar las propiedades mecánicas de una junta soldada de acero AISI 4130 de acuerdo con las normas API 6A [1] y ASME Sección IX[2], y evitar la presencia de martensita en la estructura metalográfica de la junta, siendo esta última perjudicial en los aceros y provocada por enfriamientos rápidos. Se ve la necesidad de desarrollar un procedimiento de soldadura capaz de satisfacer mencionadas condiciones si...

  14. INFLUENCIA DE LOS RECUBRIMIENTOS DÚPLEX SOBRE LAS PROPIEDADES MECÁNICAS Y RESISTENCIA AL DESGASTE DEL ACERO AISI 4140 BONIFICADO

    Directory of Open Access Journals (Sweden)

    Francisco Javier Bolívar Osorio

    Full Text Available El acero AISI 4140 es un acero de baja aleación al cromo/molibdeno de elevada resistencia mecánica y buena tenacidad, el cual se utiliza para la fabricación de piezas de maquinaria como piñones, cigüeñales, ejes de levas, etc. Sin embargo, su resistencia al desgaste es bastante limitada y suele ser mejorada mediante el tratamiento superficial de la nitruración. El propósito de este trabajo consistió en mejorar las propiedades mecánicas e incrementar la resistencia al desgaste del acero 4140 mediante la aplicación de un tratamiento superficial DUPLEX consistente en la nitruración líquida (conocida como Teniffer seguido del depósito de un recubrimiento duro de nitruro de titanio (TiN. La microestructura cristalina fue evaluada mediante difracción de rayos X, la morfología y la composición química fue determinada por microscopía SEM y espectroscopía de energía dispersiva de rayos X (EDS, las propiedades tribológicas fueron analizadas mediante mediciones en un tribómetro de tipo esfera sobre disco y la microdureza se determinó por el método Vickers. Las muestras tratadas con el recubrimiento dúplex mostraron una resistencia al desgaste 4 veces mayor que la muestra en estado bonificado, lo cual demuestra la aplicación potencial que tiene el acero 4140 sometido a este tratamiento dúplex.

  15. Susceptibility to hydrogen-induced cracking in H2S corrosion environment of API 5L-X80 weld metal

    International Nuclear Information System (INIS)

    Hilton, J.; Fals, H. C.; Trevisan, R. E.

    2009-01-01

    The susceptibility to hydrogen-induced cracking in H 2 S environment of welded API X80 steel was studied. The flux cored arc welding (FCAW) process was employed with E71-T1 and E71-T8K6 wires. The welding parameters were kept constant, but the samples were welded using different preheat temperatures (room temperature and 100 degree centigrade). The gapped bead-on-plate (G-BOP) test was used. The specimens of modified G-BOP tests were exposed to an environment saturated in H 2 S, as recommended by the NACE TM0284 standard. The weld beads were characterized by optical microscopy and the level of residual hydrogen in the samples was measured. The fracture surface areas of hydrogen-induced cracking were calculated and the fracture mode was discussed. It was found that the preheating temperature of 100 degree centigrade was enough to avoid cracking, even in the presence of H 2 S. It was also found that the E71- T8K6 wire was more susceptible to cracking, and the typical mixed-mode fracture was predominant in all samples. (Author) 15 refs

  16. Effects of Apis mellifera adansonii, L. 1758 (Apidae: Hymenoptera ...

    African Journals Online (AJOL)

    Effects of Apis mellifera adansonii, L. 1758 (Apidae: Hymenoptera) pollination on yields of Cucumeropsis mannii (Naudin) in Kisangani, Democratic Republic of Congo. Boniface Posho Ndola, Yves Brostaux, Guillaume Le Goff, Marie-Lucie Susini, Eric Haubruge, Frederic Francis, Bach Kim Nguyen ...

  17. Comparative Study of API 5L X60 and ASTM 572 Gr50 Steel Exposed to Crude Oil and Seawater

    Directory of Open Access Journals (Sweden)

    Marcy Viviana Chiquillo Márquez

    2018-04-01

    Full Text Available In the petroleum industry, the biphasic conditions in storage and separation tanks allow that the material to remain exposed to two different environments, causing its deterioration. In this article, an evaluation is made of the corrosive behavior and Vickers microhardness (HV of two high strength low alloy (HSLA steels and how their surfaces are characterized. The ASTM 572 Gr50 steel showed a lower corrosion rate in all systems after being immersed for 720 and 1440 hours. Characterizing the surface by means of Scanning Electron Microscopy (SEM showed uniform and localized corrosion for the both steels, and revealed that the ASTM 572 Gr50 steel shows pitting corrosion in crude oil systems. The electrochemical results revealed that the corrosion potential of API X60 steel was more negative; however the ASTM 572 Gr50 steel had a higher current density and a lower polarization resistance when immersed in an oil/seawater mixture. It also observed that, after being immersed in the corrosive fluids, the microstructures of the steels were not modified and variations in their microhardness (HV were minute.

  18. Mechanical properties of API X80 steel pipe joints welded by Flux Core Arc Weld Process; Propriedades mecanicas de juntas de tubos de aco API X80 soldadas com arame tubulares

    Energy Technology Data Exchange (ETDEWEB)

    Ordonez, Robert E. Cooper; Silva, Jose Hilton F.; Trevisan, Roseana E. [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica. Dept. de Engenharia de Fabricacao

    2003-07-01

    Flux Core Arc Welding processes (FCAW) are beginning to be applied in pipeline welds, however, very limited experimental data regarding mechanical properties of pipeline weld joints with these processes are available in the literature. In this paper, the effects of preheat temperature and type of FCAW on mechanical properties (microhardness and tensile strength) of API X80 weld joint steel are presented. FCAW processes with gas protection and self-shielded were used. Multipasses welding were applied in 30'' diameter and 0,625'' thickness tubes. Influence factors were: FCAW type and preheat temperature. Acceptance criteria of welded joints were evaluated by API 1104 standard for tensile strength test and ASTM E384-99 for microhardness test. The results obtained showed that FCAW type and preheat temperature have no influence on mechanical properties of API X80 joint steel. (author)

  19. Caracterización de los aceros sinterizados obtenidos a partir de polvos prealeados Fe-1,5% Mo

    Directory of Open Access Journals (Sweden)

    Torralba, J. M.

    1995-02-01

    Full Text Available Sintered molybdenum-, copper-, nickel- alloyed steels, have been studied through the influence of the Chemical composition on different mechanical and physical properties. In all the studied steels, a constant percentage of carbon has been used, as well Fe-Mo prealloyed powders, with a 1,5% Mo content. Selected sintering conditions were close to those used in the P/M industry, potential consumer of the studied steels.

    Se estudian los aceros aleados sinterizados con molibdeno, cobre, níquel y grafito, a partir de la influencia de su composición sobre distintas propiedades mecánicas y físicas. En todos los aceros, se utilizó una composición de carbono constante, así como polvos prealeados de Fe-Mo, con 1,5% Mo. Las condiciones de sinterización elegidas han sido las más próximas a las utilizadas en la industria pulvimetalúrgica, que es el usuario potencial de los materiales estudiados.

  20. Development of stress-modified fracture strain criterion for ductile fracture of API X65 steel

    International Nuclear Information System (INIS)

    Oh, Chang Kyun; Kim, Yun Jae; Park, Jin Moo; Kim, Woo Sik; Baek, Jong Hyun

    2005-01-01

    This paper presents a stress-modified fracture strain for API X65 steel used for gas pipeline, as a function of stress triaxiality. To determine the stress-modified fracture strain, tension test of bars with four different notch radii, made of API X65 steel, is firstly performed, from which true fracture strains are determined as a function of notch radius. Then detailed elastic-plastic, large strain Finite Element (FE) analyses are performed to estimate variations of stress triaxiality in the notched bars with load. Combining experimental with FE results provides the true fracture strain as a function of stress triaxiality, which is regarded as a criterion of ductile fracture. Application of the developed stress-modified fracture strain to failure prediction of gas pipes made of API X65 steel with various types of defects is discussed

  1. Short range structural models of the glass transition temperatures and densities of 0.5Na2S + 0.5[xGeS2 + (1 - x)PS5/2] mixed glass former glasses.

    Science.gov (United States)

    Bischoff, Christian; Schuller, Katherine; Martin, Steve W

    2014-04-03

    The 0.5Na2S + 0.5[xGeS2 + (1 - x)PS5/2] mixed glass former (MGF) glass system exhibits a nonlinear and nonadditive negative change in the Na(+) ion conductivity as one glass former, PS5/2, is exchanged for the other, GeS2. This behavior, known as the mixed glass former effect (MGFE), is also manifest in a negative deviation from the linear interpolation of the glass transition temperatures (T(g)) of the binary end-member glasses, x = 0 and x = 1. Interestingly, the composition dependence of the densities of these ternary MGF glasses reveals a slightly positive MGFE deviation from a linear interpolation of the densities of the binary end-member glasses, x = 0 and x = 1. From our previous studies of the structures of these glasses using IR, Raman, and NMR spectroscopies, we find that a disproportionation reaction occurs between PS7/2(4-) and GeS3(2-) units into PS4(3-) and GeS5/2(1-) units. This disproportionation combined with the formation of Ge4S10(4-) anions from GeS5/2(1-) groups leads to the negative MGFE in T(g). A best-fit model of the T(g)s of these glasses was developed to quantify the amount of GeS5/2(1-) units that form Ge4S10(4-) molecular anions in the ternary glasses (∼ 5-10%). This refined structural model was used to develop a short-range structural model of the molar volumes, which shows that the slight densification of the ternary glasses is due to the improved packing efficiency of the germanium sulfide species.

  2. Assembly of bicyclic or monocyclic clusters from [(η5-C5Me5)2Mo2(μ3-S)4(CuMeCN)2]2+ with tetraphosphine or N,P mixed ligands: syntheses, structures and enhanced third-order NLO performances.

    Science.gov (United States)

    Ren, Zhi-Gang; Sun, Sha; Dai, Min; Wang, Hui-Fang; Lü, Chun-Ning; Lang, Jian-Ping; Sun, Zhen-Rong

    2011-09-07

    Reactions of the preformed cluster [(η(5)-C(5)Me(5))(2)Mo(2)(μ(3)-S)(4)Cu(2)(MeCN)(2)](ClO(4))(2) (1) with two tetraphosphine ligands, 1,4-N,N,N',N'-tetra(diphenylphosphanylmethyl)benzene diamine (dpppda) and N,N,N',N'-tetra(diphenylphosphanylmethyl)ethylene diamine (dppeda), produced two bicyclic clusters {[(η(5)-C(5)Me(5))(2)Mo(2)(μ(3)-S)(4)Cu(2)](2)(L)}(ClO(4))(4) (3: L = dpppda; 4: L = dppeda). Analogous reactions of 1 or [(η(5)-C(5)Me(5))(2)Mo(2)(μ(3)-S)(4)Cu(2)(MeCN)(2)](PF(6))(2) (2) with two N,P mixed ligands, N,N-bi(diphenylphosphanylmethyl)-2-aminopyridine (bdppmapy) and N-diphenylphosphanylmethyl-4-aminopyridine (dppmapy), afforded two monocyclic clusters {[(η(5)-C(5)Me(5))(2)Mo(2)(μ(3)-S)(4)Cu(2)](2)(L)(2)}X(4) (5: L = bdppmapy, X = ClO(4); 6: L = dppmapy, X = PF(6)). Compounds 3-6 were fully characterized by elemental analysis, IR spectra, UV-vis spectra, (1)H and (31)P{(1)H} NMR spectra, ESI-MS and single-crystal X-ray crystallography. In the tetracations of 3-6, two cubane-like [Mo(2)(μ(3)-S)(4)Cu(2)] cores are linked either by one dpppda or dppeda bridge to form a bicyclic structure or by a pair of bdppmapy or dppmapy bridges to afford a monocyclic structure. The third-order nonlinear optical (NLO) properties of 1 and 3-6 in MeCN were also investigated by femtosecond degenerate four-wave mixing (DFWM) technique with a 50 fs pulse width at 800 nm. Compounds 3-6 exhibited enhanced third-order NLO performances relative to that of 1. This journal is © The Royal Society of Chemistry 2011

  3. Characterization of 5-(2- 18F-fluoroethoxy)-L-tryptophan for PET imaging of the pancreas

    OpenAIRE

    Abbas, Ahmed; Beamish, Christine; McGirr, Rebecca; Demarco, John; Cockburn, Neil; Krokowski, Dawid; Lee, Ting-Yim; Kovacs, Michael; Hatzoglou, Maria; Dhanvantari, Savita

    2016-01-01

    Purpose: In diabetes, pancreatic beta cell mass declines significantly prior to onset of fasting hyperglycemia. This decline may be due to endoplasmic reticulum (ER) stress, and the system L amino acid transporter LAT1 may be a biomarker of this process. In this study, we used 5-(2- 18F-fluoroethoxy)-L-tryptophan ( 18F-L-FEHTP) to target LAT1 as a potential biomarker of beta cell function in diabetes. Procedures: Uptake of 18F-L-FEHTP was determined in wild-type C57BL/6 mice by ex vivo biodis...

  4. Aceros aluminotérmicos. Nuevas aplicaciones

    Directory of Open Access Journals (Sweden)

    Duart Blay, J. M.

    2004-02-01

    . Particular aplicación o interés presentan en la tecnología de los ferrocarriles para la obtención del carril continuo, prácticamente implantado en todo el mundo y en soldaduras cable de cobre-carril de acero empleadas en las señalizaciones para control de tráfico. En este trabajo se aportan las bases termodinámicas de la aluminotermia del hierro y su aplicación a la soldadura compleja de cruzamientos, juntas de dilatación y desvíos en FF.CC, que combinan aceros Hadfield, aceros inoxidables y aceros perlíticos de diferentes propiedades mecánicas. Las uniones deben ser compactas, resistentes y duras en los niveles que se citan en el trabajo, según requisitos exigidos por la circulación en líneas de alta velocidad (350 km/h., actualmente en construcción en España, pero que resultan generalizables a otro tipo de líneas menos exigentes y a ferrocarriles mineros.

  5. Coming 5th Edition of the API Standard 618: major changes compared to the API 618, 4th edition

    NARCIS (Netherlands)

    Pyle, A.; Eijk, A.; Elferink, H.

    2003-01-01

    This paper will present the highlights of changes that will be found in the 5th Edition of API 618, which is expected to be published in late 2003 or early 2004. Approximately every 5 years the API Standards are revised in such a way that the latest field experiences and proven designs are included

  6. Mejoramiento de la resistencia a la corrosión del acero AISI 4140 utilizando multicapas de titanio/nitruro de titanio

    Directory of Open Access Journals (Sweden)

    Faber Correa

    2008-01-01

    Full Text Available El acero 4140 se utiliza ampliamente en la fabricación de partes de máquinas con durezas entre 25-35 Rockwell C. Sin embargo, su vida útil se ve limitada por su baja resistencia al desgaste y a la corrosión. Con el fin de mejorar su comportamiento frente a la corrosión se depositaron multicapas de Titanio/Nitruro de Titanio (Ti/TiN sobre substratos de acero 4140 mediante un sistema multi-blanco d.c. magnetrón sputtering a partir de un blanco de Ti de alta pureza (99,99% en una atmósfera de Ar/N2. Con el objeto de estudiar el efecto del número de capas sobre la velocidad de corrosión de las películas depositadas, se crecieron multicapas con 1, 5, 10, 15, y 20 bicapas de [Ti /TiN], manteniendo un espesor total constante de 3 um en todas ellas. Las fases existentes y composición química de los recubrimientos fueron analizados mediante espectroscopía de difracción de rayos X (XRD y espectroscopía de energía dispersiva de rayos X (EDX respectivamente. Las muestras de acero sin y con recubrimiento se caracterizaron además por Espectroscopía de Impedancia Electroquímica (EIS y curvas de polarización Tafel. Se encontró que la velocidad de corrosión tuvo una disminución alrededor del 87% en el acero recubierto con 20 bicapas de Ti/TiN en comparación al acero sin recubrir y del 25% respecto a la muestra recubierta con 1 bicapa, lo cual evidencia el efecto positivo del incremento del período en las películas delgadas basadas en multicapas de Ti/TiN.

  7. Propiedades mecánicas de las uniones por láser de aceros inoxidables dúplex

    Directory of Open Access Journals (Sweden)

    Amigó, V.

    2005-04-01

    Full Text Available The welded joints of stainless steels always present problems for the microstructural modifications that occur in the heat affected zone. Particularly, duplex stainless steels present very important changes when the weld pool solidifies forming fundamentally ferritic structures with some austenite in grain boundaries. These microstructural modifications, and those which occur in the HAZ, justify the mechanical properties of the joint and mainly those of plasticity, being all of them influenced by the processing conditions. In this work the influence of the laser welding speed on the tensile behaviour of duplex stainless steel welded joints is presented. The microstructure of the obtained seams and of the heat affected zone will be evaluated by means of optic and scanning electron microscopy. Also, different microhardness profiles have been obtained to evaluate the modifications in the mechanical properties both in the seam and the zone of thermal affection.

    Las uniones soldadas de aceros inoxidables siempre presentan problemas por las modificaciones microestructurales que suceden en la zona afectada por el calor. Particularmente, los aceros inoxidables dúplex presentan cambios microestructurales muy importantes al solidificar el cordón y formar estructuras, fundamentalmente ferríticas, con formación de austenita en borde de grano. Estas modificaciones microestructurales, junto a las que suceden en la ZAC, son las que justifican las propiedades mecánicas de la unión y fundamentalmente las de plasticidad. Y todo ello en función de las condiciones de procesado. En este trabajo se presenta la influencia de la velocidad de soldeo en las propiedades a tracción de uniones soldadas por láser de chapas de acero inoxidables dúplex. La microestructura de los cordones obtenidos y de la zona afectada por el calor se ha evaluado mediante microscopía óptica y electrónica de barrido, y se han obtenido diferentes perfiles de microdureza que

  8. Cold bending of 34'' OD API 5L X80 pipes; Curvamento a frio de tubos API 5L X80 de 34'' de diametro

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Ronaldo; Moreira, Fabio A.; Chad, Luis; Fritz, Marcelo C. [TenarisConfab, Pindamonhangaba, SP (Brazil); Batista, Gilmar Z.; Hippert, Eduardo [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    A key factor that demands special attention in the pipeline construction is the cold bending process, since 30 to 40% of the pipes use this process in the field. This study aimed to evaluate the X80 cold bending operational parameters, in order make viable the use of this process in the installation of future onshore pipelines. Three 34''OD x 0,750'' pipes were bended. The bending was conducted using a hydraulic equipment with application of equally spaced punches, recording the correspondent angles related to the elastic and plastic deformations in order to assess the spring-back effect and performing dimensional inspection. Samples from pipe and the weld were subjected to mechanical and metallographic tests. It was possible to obtain a 19 deg curve and 27D radius without presenting any evidence of wrinkles, out of roundness or any type of mechanical damage. After analysis, all criteria established from project specifications were complied, the mechanical tests performed allowed comparing pipe mechanical properties of straight and bended regions. The results of this study provide technical know how for future X80 onshore pipelines applications. (author)

  9. Comparison of angular dependence of magnetic Barkhausen noise of hysteresis and initial magnetization curve in API5L steel

    Science.gov (United States)

    Chávez-Gonzalez, A. F.; Martínez-Ortiz, P.; Pérez-Benítez, J. A.; Espina-Hernández, J. H.; Caleyo, F.

    2018-01-01

    This work analyzes the differences between the magnetic Barkhausen noise corresponding to the initial magnetization curve and Barkhausen noise corresponding to one branch of the hysteresis loop in API-5L steel. The outcomes show that the Barkhausen noise signal corresponding to the initial magnetization curve and that corresponding to the hysteresis are significantly different. This difference is due to the presence of different processes of the domain wall dynamics in both phenomena. To study the processes present in magnetization dynamics for an applied field of H > 0, research into the angular dependence of a Barkhausen signal using applied field bands has revealed that a Barkhausen signal corresponding to the initial magnetization curve is more suitable than a Barkhausen signal corresponding to the hysteresis loop.

  10. Microestructura y propiedades mecánicas de dos aceros para herramientas con ultra alto contenido de boro

    Directory of Open Access Journals (Sweden)

    Jiménez, J. A.

    1998-05-01

    Full Text Available In the present work, two selected tool steels have been modified by a boron addition of 0.5 and 1 mass %. Both steels were processed by powder metallurgy methods, including argon atomization and hot isostatic pressing. The Consolidated materials presented a microstructure consisting of a fine and homogeneous distribution borocarbides M23(C,B6 in a ferrite-martensite matrix. No changes are observed in the microstructure after deformation by compression-strain-rate-change tests at temperatures ranging from 700 to 1,100 °C. For the Fe-lB-lC steel, a stress exponent of 4.5 was obtained, that suggests that slip creep is the controlling deformation mechanism. On the other hand, a stress exponent between 2 and 3 was obtained for the Fe-0.5B-1.5C steel that suggests that grain boundary sliding is the controlling deformation mechanism. In both cases, the activation energy for creep was related to the activation energy for iron self-diffusion.

    En el presente trabajo se han modificado dos aceros para herramientas convencionales por la presencia de un contenido de boro entre 0,5 y 1 % en masa. Ambos aceros se procesaron por la ruta pulvimetalúrgica, incluyendo atomización por argón y compactación isostática en caliente. El material compactado presentó una microestructura caracterizada por una distribución de partículas de borocarburos M23(C,B6 fina y homogénea en una matriz de ferrita-martensita. Esta microestructura permanece prácticamente inalterada tras los ensayos de cambios en la velocidad de deformación durante el ensayo de compresión a temperaturas entre 750 y 1.000 °C. En el caso del acero Fe-lB-lC se obtuvo un valor para el exponente de la tensión de 4,5, que sugiere que la deformación plástica está controlada por un mecanismo de fluencia por movimiento de dislocaciones. Por otro lado, para el acero Fe-0,5B-1,5C, se obtuvieron valores para el exponente de la tensión comprendidos

  11. Fatigue crack growth behaviour of semi-elliptical surface cracks for an API 5L X65 gas pipeline under tension

    Science.gov (United States)

    Shaari, M. S.; Akramin, M. R. M.; Ariffin, A. K.; Abdullah, S.; Kikuchi, M.

    2018-02-01

    The paper is presenting the fatigue crack growth (FCG) behavior of semi-elliptical surface cracks for API X65 gas pipeline using S-version FEM. A method known as global-local overlay technique was used in this study to predict the fatigue behavior that involve of two separate meshes each specifically for global (geometry) and local (crack). The pre-post program was used to model the global geometry (coarser mesh) known as FAST including the material and boundary conditions. Hence, the local crack (finer mesh) will be defined the exact location and the mesh control accordingly. The local mesh was overlaid along with the global before the numerical computation taken place to solve the engineering problem. The stress intensity factors were computed using the virtual crack closure-integral method (VCCM). The most important results is the behavior of the fatigue crack growth, which contains the crack depth (a), crack length (c) and stress intensity factors (SIF). The correlation between the fatigue crack growth and the SIF shows a good growth for the crack depth (a) and dissimilar for the crack length (c) where stunned behavior was resulted. The S-version FEM will benefiting the user due to the overlay technique where it will shorten the computation process.

  12. Reaction of ether and thioether functionalised 1-alkenes with the cationic permethylzirconocene olefin polymerisation catalyst [(eta(5)-C5Me5)(2)ZrMe](+). Molecular structure of the insertion product [(eta(5)-C5Me5)(2)ZrCH2CH(Me)CH2OEt](+)

    NARCIS (Netherlands)

    Bijpost, Erik A; Zuideveld, Martin A.; Meetsma, Auke; Teuben, Jan H

    1998-01-01

    Reaction of [(η5-C5Me5)2ZrMe][MeB(C6F5)3] (1) with (thio)ether functionalised alkenes: 3-ethoxy-1-propene and 3-(methylthio)-1-propene gives stable insertion products [(η5-C5Me5)2ZrCH2CH(Me)CH2XR][MeB(C6F5)3] (2: X = O, R = Et; 3: X = S, R = Me) in which the (thio)ether function is intramolecularly

  13. MicroRNA-1 promotes apoptosis of hepatocarcinoma cells by targeting apoptosis inhibitor-5 (API-5).

    Science.gov (United States)

    Li, Dong; Liu, Yu; Li, Hua; Peng, Jing-Jing; Tan, Yan; Zou, Qiang; Song, Xiao-Feng; Du, Min; Yang, Zheng-Hui; Tan, Yong; Zhou, Jin-Jun; Xu, Tao; Fu, Zeng-Qiang; Feng, Jian-Qiong; Cheng, Peng; chen, Tao; Wei, Dong; Su, Xiao-Mei; Liu, Huan-Yi; Qi, Zhong-Chun; Tang, Li-Jun; Wang, Tao; Guo, Xin; Hu, Yong-He; Zhang, Tao

    2015-01-02

    Although microRNA-1 (miR-1) is a known liver cancer suppressor, the role of miR-1 in apoptosis of hepatoma cells has remained largely unknown. Our study shows that ectopic miR-1 overexpression induced apoptosis of liver hepatocellular carcinoma (HepG2) cells. Apoptosis inhibitor 5 (API-5) was found to be a potential regulator of miR-1 induced apoptosis, using a bioinformatics approach. Furthermore, an inverse relationship between miR-1 and API-5 expression was observed in human liver cancer tissues and adjacent normal liver tissues. Negative regulation of API-5 expression by miR-1 was demonstrated to promote apoptosis of HepG2 cells. Our study provides a novel regulatory mechanism of miR-1 in the apoptosis of hepatoma cells. Copyright © 2014 Federation of European Biochemical Societies. Published by Elsevier B.V. All rights reserved.

  14. O(5)sub(L)xO(5)sub(R)xU(1)sub(V) electro-weak gauge theory and the neutrino pairing mechanism

    International Nuclear Information System (INIS)

    Samiullah, M.; Mubarak, A.

    1981-08-01

    The possibility of using the group O(5)sub(L)xO(5)sub(R)xU(1)sub(V) for unifying the weak and electromagnetic interactions is studied. We are led to an anomaly free theory. Potentially the theory has the advantage of incorporating the previous results. For example, all the results of O(5)sub(L)xU(1) studies are, as a special case, obtainable at low energies. In the process of breaking the symmetry down to Weinberg-Salam theory at the level of SU(2)sub(L)xSU(2)sub(R)xU(1)sub(V), we have employed the neutrino proposed by Mannheim. We have been able to reproduce several of the conventional electroweak aspects such as the parity violation in both the lepton and charged quark sectors, Weinberg mixing pattern in the neutral current sector while keeping the left-handed neutrinos massless. All the salient features of low energy phenomenology are shown to follow. (author)

  15. Transformaciones Microestructurales en Soldaduras Disímiles de Acero Inoxidable Austenítico con Acero Inoxidable Ferrítico

    Directory of Open Access Journals (Sweden)

    Sara María Aguilar-Sierra

    2015-03-01

    Full Text Available En este trabajo se estudian los fenómenos metalúrgicos que ocurren en la soldadura SMAW de un acero inoxidable ferrítico AISI 430 con un acero inoxidable austenítico AISI 316L. Para el estudio se utilizaron dos tipos de electrodos: austenítico AWS E309L y dúplex AWS E2209-16, ambos con un diámetro de 3,2 mm. Las uniones soldadas se realizaron con un solo pase y se variaron simultáneamente la corriente y la velocidad de soldadura; las condiciones fueron 49 A y 2,4 mm.s–1como valores bajos y 107 A y 4,3 mm.s–1como valores altos. Se evaluó la influencia del tipo de electrodo y de los parámetros de soldadura en la evolución microestructural de las zonas afectadas por el calor y de las zonas de fusión, encontrando diferencias en la morfología y cantidad de ferrita delta para todas las condiciones estudiadas. Se evidenció crecimiento y refinación de grano ferrítico y formación de martensita en la zona afectada por el calor del metal base ferrítico. Se evaluó también la resistencia a la tensión hallando similitudes en todas las soldaduras.

  16. Efficiency and corrosion rate analysis of organic inhibitor utilization from bawang dayak leaves (EleutherineamericanaMerr.) on API 5L steel

    Science.gov (United States)

    Sari, Shaimah Rinda; Sari, Eli Novita; Rizky, Yoel; Sulistijono, Triana, Yunita

    2018-05-01

    This research studied the inhibition of corrosion by bawang dayak leaves extract (EleutherineamericanaMerr.) on API 5L steel in brine water environment (3.5% NaCl). The inhibitor was extracted using maceration process from bawang dayak leaves that was cultivated in Paser District, East Kalimantan. The test of antioxidant activity showed that bawang dayak leaves extract is a very powerful antioxidant with IC50 value of 27.30204. The results from FTIR test show the presence of electronegative atoms and double bonds of the alkenes groups that provide the potential of the extract as a corrosion inhibitor. Efficiency of inhibition reached up to 93.158% for the addition of inhibitor with 300 ppm concentration and 20 days of immersion time. This inhibitory behavior is also supported by polarization measurements where the lowest corrosion rate of 0.00128 mm/year is obtained at the same concentration and immersion time.

  17. Identificación de aceros por espectroscopia de rompimiento inducido por láser (LIBS) y análisis de componentes principales

    OpenAIRE

    Contreras, U.; Meneses-Nava, M.A.; Torres-Armenta, D.; Robles-Camacho, J.; Barbosa-García, O.

    2012-01-01

    En la actualidad existe una producción de mas de 100 000 aceros diferentes de acuerdo a su composición química y propiedades mecánicas; sin embargo, una vez en el mercado, no existe técnica alguna capaz de identificar y clasificar cualquier acero según su clase o grado. En este trabajo se describe un método capaz de identificar y clasificar aceros a través de la determinación de su composición química. El método propuesto se basa en un análisis de espectroscopia atómica procedente de la técni...

  18. A testis-specific and testis developmentally regulated tumor protein D52 (TPD52)-like protein TPD52L3/hD55 interacts with TPD52 family proteins

    International Nuclear Information System (INIS)

    Cao Qinhong; Chen Jie; Zhu Li; Liu Yun; Zhou Zuomin; Sha Jiahao; Wang Shui; Li Jianmin

    2006-01-01

    Tumor protein D52-like proteins (TPD52) are small coiled-coil motif bearing proteins that were first identified in breast cancer. TPD52 and related proteins have been implicated in cell proliferation, apoptosis, and vesicle trafficking. To date, three human TPD52 members had been identified, named hD52 (TPD52), hD53 (TPD52L1), and hD54 (TPD52L2). The most important characteristic of the protein family is a highly conserved coiled-coil motif that is required for homo- and heteromeric interaction with other TPD52-like proteins. Herein, we identified a novel TPD52-like sequence (TPD52L3, or hD55) in human testis using cDNA microarray. Sequence analysis of the deduced protein suggests that hD55 contains a coiled-coil motif and is highly conserved compared with other TPD52-like sequences. Yeast two-hybrid and GST pull-down assays revealed that hD55 interacts with hD52, hD53, hD54, and itself. cDNA microarray detection found that hD55 was expressed at 5.6-fold higher levels in adult testis than in fetal testis. Additionally, the expression profile shows that hD55 is testis-specific, indicating a potential role for hD55 in testis development and spermatogenesis

  19. Lubricación del contacto aluminio-acero con líquidos iónicos en atmósfera controlada

    OpenAIRE

    Llopis Morales, Miguel

    2016-01-01

    El objetivo del presente proyecto es estudiar el comportamiento tribológico de diferentes líquidos iónicos en el contacto aluminio-acero y las interacciones superficiales que se producen. Para realizar el estudio tribológico, se llevará a cabo un estudio de corrosión previo por lo que será necesario realizar ensayos de corrosión y tribológicos. En cuanto a los objetivos de los ensayos de corrosión, el objetivo que se quiere alcanzar con este ensayo es comprobar si se produce algún tipo de cor...

  20. Effects of C and Si on strain aging of strain-based API X60 pipeline steels

    Science.gov (United States)

    Sung, Hyo Kyung; Lee, Dong Ho; Lee, Sunghak; Lee, Byeong-Joo; Hong, Seung-Pyo; Kim, Young-Woon; Yoo, Jang Yong; Hwang, Byoungchul; Shin, Sang Yong

    2017-05-01

    Four types of strain-based API X60 pipeline steels were fabricated by varying the C and Si contents, and the effects of C and Si on strain aging were investigated. The 0.05 wt% C steels consisted mainly of polygonal ferrite (PF), whereas the 0.08 wt% C steels consisted of acicular ferrite (AF). The volume fraction of AF increased with increasing C content because C is an austenite stabilizer element. The volume fractions of bainitic ferrite (BF) of the 0.15 wt% Si steels were higher than those of the 0.25 wt% Si steels, whereas the volume fractions of the secondary phases were lower. From the tensile properties before and after the aging process of the strainbased API X60 pipeline steels, the yield strength increased and the uniform and total elongation decreased, which is the strain aging effect. The strain aging effect in the strain-based API X60 pipeline steels was minimized when the volume fraction of AF was increased and secondary phases were distributed uniformly. On the other hand, an excessively high C content formed fine precipitates, and the strain aging effect occurred because of the interactions among dislocations and fine precipitates.

  1. Optimización de los Parámetros de Soldadura por Arco Sumergido en Acero HSLA: una Aplicación para Manufactura de Tuberías de Conducción de Hidrocarburos

    Directory of Open Access Journals (Sweden)

    Patricia Sheilla Costa

    2015-12-01

    Full Text Available Resumen El acero HSLA (High Strength Low Alloy API 5L X70 es utilizado para fabricación de tuberías para transporte de hidrocarburos. La construcción de tuberías de este material involucra alta cantidad de soldadura, donde los parámetros empleados influyen directamente en las estructuras metalúrgicas y en las propiedades mecánicas del mismo cuando soldado. Así, para estudiar el impacto de los parámetros de soldadura por arco sumergido en la resistencia mecánica y dureza de la Zona Afectada por el Calor (ZAC, fue llevado a cabo un diseño central compuesto que totalizó 17 pruebas. Las variables de entrada fueron corriente, voltaje y velocidad de avance; como variables de salida se consideró resistencia a la tensión y dureza Vickers de la ZAC. Para tal estudio fue utilizado el proceso de soldadura por arco sumergido, pruebas de tensión y pruebas de dureza Vickers. Se utilizó la metodología de superficie de respuesta para el modelado y la optimización fue realizada utilizando algoritmos genéticos y la gráfica de frente de Pareto. Fueron obtenidas 16 combinaciones de parámetros con la optimización, de las cuales fue escogida una para validar los modelos. Con los resultados fue posible establecer modelos matemáticos empíricos satisfactorios para las variables de respuesta.

  2. Estudio del comportamiento a fluencia en caliente de un acero avanzado de alta resistencia de bajo contenido en carbono NiCrVCu microaleado con boro

    OpenAIRE

    González Sala, Sara

    2009-01-01

    Una de las líneas de investigación prioritarias en el contexto internacional es el desarrollo de aceros avanzados de alta resistencia (AHSS) con excelentes propiedades de resistencia y tenacidad para aplicaciones en la industria automotriz, naval, aeronáutica y de generación de energía, que permitan disminuir el peso de los componentes y sustituyan aceros tradicionales de contenidos mayores de carbono. Los aceros AHSS microaleados al boro, debido a sus cualidades, tecnología de...

  3. TAE+ 5.2 - TRANSPORTABLE APPLICATIONS ENVIRONMENT PLUS, VERSION 5.2 (DEC RISC ULTRIX VERSION)

    Science.gov (United States)

    TAE SUPPORT OFFICE

    1994-01-01

    programs to display and control the user interfaces. Since the WPTs access the workbench-generated resource files during each execution, details such as color, font, location, and object type remain independent from the application code, allowing changes to the user interface without recompiling and relinking. In addition to WPTs, TAE Plus can control interaction of objects from the interpreted TAE Command Language. TCL provides a means for the more experienced developer to quickly prototype an application's use of TAE Plus interaction objects and add programming logic without the overhead of compiling or linking. TAE Plus requires MIT's X Window System and the Open Software Foundation's Motif. The HP 9000 Series 700/800 version of TAE 5.2 requires Version 11 Release 5 of the X Window System. All other machine versions of TAE 5.2 require Version 11, Release 4 of the X Window System. The Workbench and WPTs are written in C++ and the remaining code is written in C. TAE Plus is available by license for an unlimited time period. The licensed program product includes the TAE Plus source code and one set of supporting documentation. Additional documentation may be purchased separately at the price indicated below. The amount of disk space required to load the TAE Plus tar format tape is between 35Mb and 67Mb depending on the machine version. The recommended minimum memory is 12Mb. Each TAE Plus platform delivery tape includes pre-built libraries and executable binary code for that particular machine, as well as source code, so users do not have to do an installation. Users wishing to recompile the source will need both a C compiler and either GNU's C++ Version 1.39 or later, or a C++ compiler based on AT&T 2.0 cfront. TAE Plus was developed in 1989 and version 5.2 was released in 1993. TAE Plus 5.2 is available on media suitable for five different machine platforms: (1) IBM RS/6000 series workstations running AIX (.25 inch tape cartridge in UNIX tar format), (2) DEC RISC

  4. A cluster of deaths involving 5-(2-aminopropyl)indole (5-IT).

    Science.gov (United States)

    Kronstrand, Robert; Roman, Markus; Dahlgren, Maria; Thelander, Gunilla; Wikström, Maria; Druid, Henrik

    2013-10-01

    During 2012, the designer drug 5-(2-aminopropyl)indole emerged in Sweden, and became available at different web sites under the name 5-IT or 5-API. This compound is an indole derivative and a positional isomer of alpha-methyltryptamine. In this paper, we report the pathology and toxicology from 15 deaths involving 5-IT. Routine postmortem toxicology was performed in femoral blood, using a targeted screening for pharmaceuticals and drugs of abuse with liquid chromatography time-of-flight technology, and positive results were quantified using chromatographic techniques. For 5-IT, a new method was developed using ultra-high-performance liquid chromatography and tandem mass spectrometry. In 11 cases, intoxication was the cause of death. Two cases were signed out as causa ignota, and they were considered to be natural deaths. All determinations of 5-IT were performed in femoral blood and the concentrations ranged from 0.7 to 18.6 µg/g. Two cases had 5-IT as the only drug identified, while the others presented with other psychotropic drugs or medications in the blood as well. Shortly after this series of deaths, 5-IT was scheduled as a hazardous substance according to the regulation Certain Goods Dangerous to Health on 18 September 2012 prohibiting the handling and selling of the drug. Since then, no positive cases have been found.

  5. New results from the UA5/2-experiment

    International Nuclear Information System (INIS)

    Geich-Gimbel, C.

    1985-01-01

    This paper covers recent and unpublished results from the investigation of pp-bar-interactions at √s = 200 and 900 GeV with a streamer chamber detector (UA5/2-experiment) at the CERN SPS Collider. The author concentrates on cross section measurements and searches for unusual phenomena. The data these preliminary results are based upon were taken during a very successful run of the pulsed pp-bar-Collider at CERN in spring 1985. The UA5/2 detector took 115,000 streamer chamber pictures and 500,000 electronic events (i.e. only containing information from the trigger hodoscopes and the hadron calorimeter), mainly at the flat bottom at 100 GeV beam energy and the four seconds flat top at 450 GeV of the cycle. For part of the run, an additional photon converter plate was introduced between the beam pipe and the upper streamer chamber to increase the photon detection efficiency at large production angles. The UA5/2-detector consists of two large streamer chambers (6 x 1.25 x 0.5 m/sup 3/ visible volume), placed above and below the 2 mm thick beryllium beam pipe. The azimuthal coverage of the chambers is 95% for a pseudorapidity absolute value of n ≤, 3

  6. Influence of the maximum applied magnetic field on the angular dependence of Magnetic Barkhausen Noise in API5L steels

    Energy Technology Data Exchange (ETDEWEB)

    Martínez-Ortiz, P. [Laboratorio de Evaluación No Destructiva Electromagnética (LENDE), ESIME-SEPI, Edif. Z-4, Instituto Politécnico Nacional, Zacatenco, México D.F. (Mexico); Pérez-Benítez, J.A., E-mail: japerezb@ipn.mx [Laboratorio de Evaluación No Destructiva Electromagnética (LENDE), ESIME-SEPI, Edif. Z-4, Instituto Politécnico Nacional, Zacatenco, México D.F. (Mexico); Espina-Hernández, J.H. [Laboratorio de Evaluación No Destructiva Electromagnética (LENDE), ESIME-SEPI, Edif. Z-4, Instituto Politécnico Nacional, Zacatenco, México D.F. (Mexico); Caleyo, F. [Departamento de Ingeniería Metalúrgica, ESIQIE, UPALM Edif. 7, Instituto Politécnico Nacional, Zacatenco, C.P. 07738 México D.F. (Mexico); Mehboob, N.; Grössinger, R. [Institute of Solid State Physics, Vienna University of Technology, Vienna A-1040 (Austria); Hallen, J.M. [Departamento de Ingeniería Metalúrgica, ESIQIE, UPALM Edif. 7, Instituto Politécnico Nacional, Zacatenco, C.P. 07738 México D.F. (Mexico)

    2016-03-01

    This work studies the influence of the maximum applied magnetic field on the angular dependence of the energy of the Magnetic Barkhausen Noise signal in three different API5L pipeline steels. The results show that the shape of the angular dependence of the Magnetic Barkhausen Noise energy changes with the increase of the amplitude of the applied magnetic field. This phenomenon is a consequence of the presence of unlike magnetization processes at different magnitudes of the applied magnetic field. The outcomes reveal the importance of controlling the value of the maximum applied field as parameter for the improvement of the MBN angular dependence measurements. - Highlights: • Study the angular dependence of MBN with applied field in three pipeline steels. • Reveals the change of this angular dependence with the increase applied field. • Explains this dependence based on the domain wall dynamics theory.

  7. Influence of the maximum applied magnetic field on the angular dependence of Magnetic Barkhausen Noise in API5L steels

    International Nuclear Information System (INIS)

    Martínez-Ortiz, P.; Pérez-Benítez, J.A.; Espina-Hernández, J.H.; Caleyo, F.; Mehboob, N.; Grössinger, R.; Hallen, J.M.

    2016-01-01

    This work studies the influence of the maximum applied magnetic field on the angular dependence of the energy of the Magnetic Barkhausen Noise signal in three different API5L pipeline steels. The results show that the shape of the angular dependence of the Magnetic Barkhausen Noise energy changes with the increase of the amplitude of the applied magnetic field. This phenomenon is a consequence of the presence of unlike magnetization processes at different magnitudes of the applied magnetic field. The outcomes reveal the importance of controlling the value of the maximum applied field as parameter for the improvement of the MBN angular dependence measurements. - Highlights: • Study the angular dependence of MBN with applied field in three pipeline steels. • Reveals the change of this angular dependence with the increase applied field. • Explains this dependence based on the domain wall dynamics theory.

  8. Optimización topológica y fabricación aditiva de un soporte aeronáutico mediante sinterizado láser de acero inoxidable 15-5PH

    OpenAIRE

    Marchal Montes, Álvaro

    2016-01-01

    El objetivo de este trabajó será la aplicación de la optimización topológica a un soporte usado en el sector aeronáutico para reducir su masa que posteriormente se fabricará mediante fabricación aditiva con tecnología DMLS (Direct Metal Laser Sintering) en acero inoxidable 15-5PH. Para llegar a una buena optimización topológica será necesario estudiar todos los caminos de optimización posibles hasta llegar a una correcta mediante softwares adecuados además de adaptarla a la fabricación ad...

  9. Gaseous hydrogen embrittlement of an API X80 ferrito-pearlitic steel; Fragilisation par l'hydrogene gazeux d'un acier ferrito-perlitique de grade API X80

    Energy Technology Data Exchange (ETDEWEB)

    Moro, I.

    2009-11-15

    This work deals with hydrogen embrittlement, at ambient temperature and under a high pressure gaseous way, of an API X80 high elasticity limit steel used for pipelines construction, and with the understanding of the associated physical mechanisms of the embrittlement. At first has been described a bibliographic study of the adsorption, absorption, diffusion, transport and trapping of hydrogen in the steels. Then has been carried out an experimental and numerical study concerning the implantation in the finite element code CASTEM3M of a hydrogen diffusion model coupled to mechanical fields. The hydrogen influence on the mechanical characteristics of the X80 steel, of a ferrito-pearlitic microstructure has been studied with tensile tests under 300 bar of hydrogen and at ambient temperature. The sensitivity of the X80 steel to hydrogen embrittlement has been analyzed by tensile tests at different deformation velocities and under different hydrogen pressures on axisymmetrical notched test specimens. These studies show that the effect of the hydrogen embrittlement vary effectively with the experimental conditions. Moreover, correlated with the results of the tests simulations, it has been shown too that in these experimental conditions and for that steel, the hydrogen embrittlement is induced by three different hydrogen populations: the hydrogen trapped at the ferrite/perlite interfaces, the hydrogen adsorbed on surface and the reticular hydrogen trapped in the material volume. At last, the tensile and rupture tests of specimens, during which atmosphere changes have been carried out, have shown a strong reversibility of the hydrogen embrittlement, associated with its initiation as soon as hydrogen is introduced in the atmosphere. At last, three hydrogen mechanisms, depending of the different hydrogen populations are presented and discussed. (O.M.)

  10. Estudio de la resistencia a la corrosión por picadura de aceros inoxidables austeníticos: influencia de la adición de manganeso en solución sólida

    OpenAIRE

    José Wilmar Calderón-Hernández; Lara Beatriz Braga Luz; Duberney Hincapie-Ladino; Neusa Alonso-Falleiros

    2015-01-01

    Este documento presenta los resultados de una investigación sobre la influencia del Mn en solución sólida sobre la resistencia a la corrosión por picadura de dos aceros inoxidables austeníticos, uno denominado 17Cr6Mn5Ni y un acero comercial UNS S304L utilizado como material de referencia. Fueron usadas soluciones electrolíticas de 0,6M NaCl en tres diferentes condiciones de concentración de oxígeno (solución desaireada, naturalmente aireada y aireada artificialment...

  11. Influencia de la adición de cobre y de bronce sobre las propiedades de los aceros inoxidables austeníticos sinterizados

    Directory of Open Access Journals (Sweden)

    Velasco, F.

    1997-04-01

    Full Text Available The effect that, on AISI 316L and 304L stainless steels alloyed with copper and bronze in different percentages up to a maximun of 20 % wt, produce both the alloying content and the sintering temperature over physical and mechanical properties and over the microstructure of sintered stainless steels are studied. Alloying with copper and bronze improves the density of sintered steels at the two sintering temperatures used. Copper and bronze promote liquid phase sintering (transitory or permanent, that activates sintering process. Tensile strength of stainless steel is highly improved for higher alloying contents. Moreover, tensile strength presents greater values alloying with bronze than with copper.

    Partiendo de los aceros inoxidables AISI 316L y 304L a los que se añadió cobre y bronce en diferentes porcentajes hasta el 20 % en peso, se estudia el efecto que la cantidad de aleante y la temperatura de sinterización tienen sobre las propiedades físicas y mecánicas y sobre la microestructura de los aceros inoxidables sinterizados. La aleación con cobre y con bronce aumenta la densidad de los aceros sinterizados para las dos temperaturas de sinterización utilizadas. El cobre y el bronce provocan la aparición de fase líquida (transitoria o permanente que activa el proceso de sinterización. La resistencia a la tracción del acero inoxidable experimenta un fuerte incremento para los contenidos más elevados de aleante. Además, la resistencia a la tracción alcanza mayores valores para la aleación con bronce que con cobre.

  12. Comportamiento frente al desgaste y fricción de aceros empleados en líneas de manutención aérea ensayados con y sin lubricación

    Directory of Open Access Journals (Sweden)

    Castro Regal, G.

    2005-06-01

    Full Text Available The sliding friction and wear behaviour of different steel qualities were investigated with and without lubrication conditions. Steel qualities tested are normally used in the overhead conveyor system of many industrial fields, like the automotive sector. Sliding wear tests have been conducted by means of a pin-on-disk machine. A 100Cr6 steel similar to that used within the overhead conveyor trolleys has been employed as a pin. Friction coefficient values obtained under lubrication conditions were three times smaller than those obtained without lubrication. The mechanism that controls wear behaviour under lubrication conditions is an abrasive one and the wear values obtained are almost worthless. On the other hand, mechanism controlling wear during non lubrication tests, was a combination of abrasion and adhesion

    Se ha evaluado el comportamiento frente a fricción y el desgaste de distintas calidades de acero ensayadas bajo condiciones de lubricación y sin lubricación. Las calidades de acero seleccionadas son las que normalmente se emplean en los sistemas de manutención aérea de numerosos procesos de producción, como la fabricación de automóviles. Se han realizado ensayos de desgaste tipo punzón-disco mediante un punzón de acero de calidad100Cr6, empleado en los carros que circulan por las líneas de manutención aérea. Se ha observado que el valor del coeficiente de fricción obtenido bajo condiciones de lubricaciones, aproximadamente, tres veces menor que el obtenido sin lubricación. Por otro lado, el mecanismo que controla el proceso de desgaste de los aceros ensayados con lubricación es un mecanismo de desgaste abrasivo y los valores de desgaste obtenidos son prácticamente despreciables. El desgaste de los aceros ensayados sin lubricación se produjo por combinación de dos mecanismos de desgaste: abrasión y adhesión.

  13. Resolution and sensitivity of the eyes of the Asian honeybees Apis florea, Apis cerana and Apis dorsata.

    Science.gov (United States)

    Somanathan, Hema; Warrant, Eric J; Borges, Renee M; Wallén, Rita; Kelber, Almut

    2009-08-01

    Bees of the genus Apis are important foragers of nectar and pollen resources. Although the European honeybee, Apis mellifera, has been well studied with respect to its sensory abilities, learning behaviour and role as pollinators, much less is known about the other Apis species. We studied the anatomical spatial resolution and absolute sensitivity of the eyes of three sympatric species of Asian honeybees, Apis cerana, Apis florea and Apis dorsata and compared them with the eyes of A. mellifera. Of these four species, the giant honeybee A. dorsata (which forages during moonlit nights) has the lowest spatial resolution and the most sensitive eyes, followed by A. mellifera, A. cerana and the dwarf honeybee, A. florea (which has the smallest acceptance angles and the least sensitive eyes). Moreover, unlike the strictly diurnal A. cerana and A. florea, A. dorsata possess large ocelli, a feature that it shares with all dim-light bees. However, the eyes of the facultatively nocturnal A. dorsata are much less sensitive than those of known obligately nocturnal bees such as Megalopta genalis in Panama and Xylocopa tranquebarica in India. The differences in sensitivity between the eyes of A. dorsata and other strictly diurnal Apis species cannot alone explain why the former is able to fly, orient and forage at half-moon light levels. We assume that additional neuronal adaptations, as has been proposed for A. mellifera, M. genalis and X. tranquebarica, might exist in A. dorsata.

  14. Efectos del tratamiento térmico en la fractura de aceros

    Directory of Open Access Journals (Sweden)

    Héctor Hernández A.

    1992-05-01

    Full Text Available No obstante de los avances logrados en otros tipos de aleaciones, los aceros se siguen utilizando en forma extensiva en la construcción de elementos estructurales, porque con una adecuada selección y tratamiento técnico, los aceros permiten obtener una conveniente combinación de propiedades mecánicas ante unas exigencias específicas de servicio. La fractura en elementos de máquinas frecuentemente se encuentra asociada a una discontinuidad, la cual provoca una concentración de esfuerzo, lo que puede originar sitios de iniciación de una falla por fractura. La carga límite de fractura es afectada por parámetros geométricos, naturaleza y tipo de carga y propiedades mecánicas del material. La mayoría de fallas por fractura de elementos de máquinas son fallas por fatiga; por lo general una fractura por fatiga tiene lugar por una progresiva generación y crecimiento de grietas hasta obtenerse una condición crítica de fractura súbita de la sección residual resistente. Frecuentemente en una fractura por fatiga se observan marcas de playa, las cuales son evidencias de la posición del frente de grietas antes que se alcance la condición de fractura súbita final. En este trabajo se muestra como el tratamiento térmico de temple y revenido de los aceros afecta el esfuerzo límite de falla por fractura para carga de tracción estática y carga de fatiga uniaxial con la presencia de una entalla severa. También se estudia el efecto del tratamiento térmico en la tenacidad de fractura, propiedad que cuantifica la resistencia al crecimiento súbito de una grieta bajo carga estática.

  15. Transferencia de calor en la colada continua de aceros. I parte. El molde

    Directory of Open Access Journals (Sweden)

    Cicutti, C.

    1997-10-01

    Full Text Available The continuous casting mold plays the important role of receiving the liquid steel and allowing an uniform and defect free solidified skin to be developed. In this work, the different heat transfer mechanisms which are present from the liquid steel to the mold cooling water are reviewed. The effect of operating variables on heat extraction and the relationship between global and distributed heat flux are also analyzed.

    El molde de colada continua cumple la importante función de recibir el acero líquido y permitir que se desarrolle una capa solidificada uniforme y libre de defectos. En este trabajo se revisan los distintos mecanismos implicados en el proceso de transferencia de calor, desde el acero líquido hasta el agua de refrigeración del molde. Se analiza también el efecto de las distintas variables de funcionamiento en la extracción calórica producida y la relación entre el flujo global de calor y su distribución a lo largo del molde.

  16. Degradation of impact fracture during accelerated aging of weld metal on microalloyed steel; Degradacion de la tenacidad al impacto durante el envejecimiento acelerado de soldadura en acero microaleado

    Energy Technology Data Exchange (ETDEWEB)

    Vargas-Arista, B.; Hallen, J. M.; Albiter, A.; Angeles-Chavez, C.

    2008-07-01

    The effect of accelerated aging on the toughness and fracture of the longitudinal weld metal on an API5L-X52 line pipe steel was evaluated by Charpy V-notch impact test, fracture analysis and transmission electron microscopy. Aging was performed at 250 degree centigrade for 100 to 1000 h. The impact results indicated a significant reduction in the fracture energy and impact toughness as a function of aging time, which were achieved by the scanning electron microscope fractography that showed a decrease in the vol fraction of microvoids by Charpy ductile failure with the aging time, which favored the brittle fracture by transgranular cleavage. The minimum vol fraction of microvoids was reached at 500 h due to the peak aged. The microstructural analysis indicated the precipitation of transgranular iron nano carbides in the aged specimens, which was related to the deterioration of toughness and change in the ductile to brittle behavior. (Author) 15 refs.

  17. Building Hypermedia APIs with HTML5 and Node

    CERN Document Server

    Amundsen, Mike

    2011-01-01

    With this concise book, you'll learn the art of building hypermedia APIs that don't simply run on the Web, but that actually exist in the Web. You'll start with the general principles and technologies behind this architectural approach, and then dive hands-on into three fully-functional API examples. Too many APIs rely on concepts rooted in desktop and local area network patterns that don't scale well-costly solutions that are difficult to maintain over time. This book shows system architects and web developers how to design and implement human- and machine-readable web services that remain

  18. Effects of Lactobacillus Johnsonii AJ5 Metabolites on Nutrition, Nosema Ceranae Development and Performance of Apis Mellifera L.

    Directory of Open Access Journals (Sweden)

    Piano Fiorella G. De

    2017-06-01

    Full Text Available The European honey bee (Apis mellifera L. is known to be affected by such stress factors as pathogen load, poor nutrition and depressed immunity. Nosema ceranae is one of the main parasites that affect colony populations. The relationship between the stress factors and honey bee-bacteria symbiosis appears as an alternative to enhance bee health. The aim of this study was to evaluate the effect of the oral administration of bacterial metabolites produced by Lactobacillus johnsonii AJ5 on nutritional parameters, the N. ceranae development and the performance of A. mellifera colonies. Laboratory assays were performed and demonstrated that the bacterial metabolites did not have a toxic effect on bees. Field trial showed an increase of colonies population over time. Also, a decreasing trend of fat bodies per bee was detected in all colonies but there were no evident changes on abdomen protein content at the end of the assay. Lastly, N. ceranae prevalence showed a tendency to reduce with the organic acids. Future studies should be performed to increase our knowledge of the physiological effects of bacterial metabolites on the health of bee colonies.

  19. AUMENTO EN LA RESISTENCIA A LA CORROSIÓN DE UN ACERO T91 ALUMINIZADO

    Directory of Open Access Journals (Sweden)

    LUZ S. QUINTERO

    2011-01-01

    Full Text Available El acero ferrítico T91 ha sido ampliamente utilizado en plantas de generación de energía eléctrica, calderas y plantas nucleares. Sin embargo, su resistencia a la oxidación se ve gravemente afectada a temperaturas superiores a los 600ºC. En esta investigación se empleó la técnica de cementación empacada para aluminizar un acero T91 y se encontraron las condiciones óptimas para la formación de un recubrimiento libre de porosidad y con espesor uniforme (300 micras. Se evaluó la capa de óxido formada luego de una exposición a 800ºC en atmósfera de aire. La caracterización del recubrimiento y de la capa de óxido (Al2O3 se llevó a cabo empleando un microscopio electrónico de barrido (SEM, Espectroscopia de Rayos X (EDX y mapping. Se comprobó una buena resistencia a la oxidación del acero T91 aluminizado, debido a la formación de una fina capa continua de óxido de aluminio de aproximadamente 6 micras de espesor luego de una exposición de 7 días.

  20. Recubrimiento de acero con polidopamina

    OpenAIRE

    Carrasco Rodríguez, Javier

    2013-01-01

    Se ha obtenido recubrimientos de polidopamina en acero mecánicamente resistentes y con tiempos de obtención relativamente pequeños a través de la polimerización de la dopamina bajo diferentes condiciones.

  1. Efeitos de atrativos e repelentes sobre o comportamento da abelha (Apis mellifera, l. Effect of attractants and repellents on the behavior of honey bees (Apis mellipera, L.

    Directory of Open Access Journals (Sweden)

    D.T. MALERBO-SOUZA

    1998-01-01

    Full Text Available O objetivo do presente ensaio foi testar diversas substâncias e verificar sua atratividade e repelência para abelhas, Apis mellifera, L. Para isso, foram realizados testes em discos próximos às colméias e em cana picada oferecida como alimentação para gado bovino confinado. Nos discos próximos à colméia, o produto mais atrativo foi Bee-Here e o mais repelente foi o óleo de citronela. No cocho para bovinos, o repelente mais efetivo foi n-octyl-acetato.The experiment aimed to study honey bee (Apis mellifera attractants and repellents in vitro and on chopped sugar cane for bovine feeding. Tests were performed on plates located near to the hives and on bovine-hods. On plates, Bee-Here® was the most attractive and citronela oil the most repellent. On bovine-hods the most effective was n-octyl-acetate.

  2. ESTUDIO DE LA CORROSIÓN DEL ACERO EMBEBIDO EN CONCRETO AAS SOMETIDO A CLORUROS

    Directory of Open Access Journals (Sweden)

    ROBINSON TORRES GÓMEZ

    2010-01-01

    Full Text Available Se presenta un estudio sobre el comportamiento frente a la corrosión de barras de acero de refuerzo de un concreto de escoria activado alcalinamente. La escoria de alto horno fue activada mediante el uso de silicato sódico al 5% obteniéndose un material con buenas propiedades cementantes. Las probetas de concreto fueron fabricadas a partir de este cemento, después de mezclar con los agregados fueron reforzadas con barras de acero sismoresistente ASTMA706. Las probetas de concreto reforzado estuvieron sometidas en ambientes contaminados con iones cloruro para simular condiciones marinas. La evaluación electroquímica se realizo aplicando las técnicas de resistencia a la polarización lineal (LPR y espectroscopia de impedancia electroquímica (EIS. Se logra determinar el comportamiento de la capa pasiva del acero y electroquímico del metal cuando está inmerso en estos materiales cerámicos novedosos.

  3. Evaluation of Yield Component Traits of Honeybee-Pollinated (Apis mellifera L.Rapeseed Canola (Brassica napus L. Evaluación de Parámetros de Rendimiento del Raps (Brassica napus L. Polinizado por Abejas (Apis mellifera L.

    Directory of Open Access Journals (Sweden)

    Ximena Araneda Durán

    2010-06-01

    Full Text Available Recent introduction of hybrid varieties raises the question if bees (Apis mellifera L. contribute as pollinator agents in developing the full yield potential of rapeseed (Brassica napus L.. In order to evaluate the yield achieved by B. napus cv. Artus pollinated by A. mellifera testing was carried out in the district of Freire, La Araucanía Region, Chile. This consisted in isolating or excluding rapeseed plants from pollinators with exclusion cages. Treatments applied were total exclusion (T1, partial exclusion (T2 and free pollination (T0 with a density of 6.5 hives ha-1, in order to determine the following yield components traits: grains per silique, siliques per plant, 1000 grain weight and yield. The experimental design used was randomized complete blocks with three treatments and three replicates. Results obtained show that the parameter least affected by bee intervention was the grains per silique variable. In contrast, siliques per plant and 1000 grain weight parameters presented significant differences, contributing to a yield greater than 5 t ha-1; which represented a figure 50.34% higher than in the treatment without bees. It may be concluded that the inclusion of bees in crops is fully justified as a production tool.La reciente introducción de variedades híbridas plantea la interrogante de la contribución que pueda tener la presencia de abejas (Apis mellifera L. como agentes polinizadores para desarrollar en pleno el potencial productivo del raps (Brassica napus L.. Con el objetivo de evaluar el rendimiento alcanzado por B. napus cv. Artus polinizado por A. mellifera, se realizó un ensayo en la localidad de Freire, Región de La Araucanía, Chile. Éste consistió en aislar o excluir las plantas de raps de los polinizadores mediante el uso de jaulas excluidoras. Los tratamientos consistieron en la exclusión total (T1, exclusión parcial (T2 y libre polinización (T0 con una densidad de 6,5 colmenas ha-1, con el fin de determinar

  4. The effect of hot strip mill processing parameters and alloy addition on low temperature toughness of API-X70 steel

    Energy Technology Data Exchange (ETDEWEB)

    Ro, Kwang Seop; Al-Shammary, Saad; Al-Butairi, Adel A. [QA and PTS, SAUDI IRON and STEEL COMAPNY, Al-Jubail, (Saudi Arabia); Al-Hajeri, Khaled F. [Saudi Basic Industries Corporation, Jubail, (Saudi Arabia)

    2010-07-01

    The design of high strength steel grade is based on stringent specifications in terms of chemistry, mechanical properties and surface requirements. This study investigated the effect of alloy addition on low temperature toughness of API X70 pipeline steel. Seven different chemical compositions have been selected for experimental testing. Ni, Cr and Cu were added in various quantities to the tested material without deteriorating the phase transformation to acicular ferrite. A tensile test, Charpy impact test, DWTT pressed notch test and microstructural observations using optical microscope and SEM were carried out. Statistical analyses were done to identify the relationship between chemical composition and DWTT shear area. The following equation showed excellent agreement with the experimental test data: Pct Shear aero of DWTT (-10 degrees C) = 954 - 0.3*SRT + 0.5*TBT - 0.4*FRT + 0.04*CT - 306*C - 60*(Mn+Ni+Cu) + 38*(Mo+Cr) - 791*(Ti+Nb+V) - 4*MA. The results showed that it is possible to design high strength API X 70 steel grades with good DWTT toughness by using the statistical equation that was developed.

  5. RESISTENCIA A LA CORROSIÓN DE LAS MULTICAPAS DE [TIN/ALTIN]n DEPOSITADAS SOBRE ACERO AL CARBONO AISI 1045

    Directory of Open Access Journals (Sweden)

    WILLIAM APERADOR

    2011-01-01

    Full Text Available En este artículo se presenta el mejoramiento frente a la corrosión de los recubrimientos multicapas de [TiN/AlTiN]n con periodos de 2, 6, 12 y 24 bicapas depositados mediante la técnica de PVD magnetrón Sputtering sobre acero al carbono AISI 1045. La evaluación electroquímica se realizó mediante las técnicas espectroscopia de impedancia electroquímica (EIS y curvas de polarización Tafel, en una solución de 0.5M de H2SO4 + 3.5% wt. de NaCl. La resistencia a la corrosión aumentó de forma gradual en función del número de bicapas en comparación al sustrato encontrando valores de velocidad de corrosión de 18.51 mpy para el sustrato sin recubrir y de 1x10 6 mpy para la muestra con 24 bicapas. Los resultados electroquímicos revelan el efecto positivo en cuanto a la protección superficial del acero 1045 con el incremento del periodo en las multicapas de [TiN /AlTiN]n.

  6. 44 CFR 5.2 - Application.

    Science.gov (United States)

    2010-10-01

    ... 44 Emergency Management and Assistance 1 2010-10-01 2010-10-01 false Application. 5.2 Section 5.2 Emergency Management and Assistance FEDERAL EMERGENCY MANAGEMENT AGENCY, DEPARTMENT OF HOMELAND SECURITY GENERAL PRODUCTION OR DISCLOSURE OF INFORMATION General Provisions § 5.2 Application. This part applies to...

  7. Profundidad del surco gingival en dientes primarios restaurados con coronas de acero cromo

    Directory of Open Access Journals (Sweden)

    Rubén Muñoz Delgado

    2015-01-01

    Full Text Available Objetivo: Evaluar la relación entre el ajuste marginal y la profundidad del surco gingival en dientes primarios restaurados con coronas de acero cromo. Métodos: Se midió la profundidad del surco gingival de 114 dientes primarios restaurados con coronas de acero cromo en 67 niños, ambos sexos, de 3 a 6 años de edad de la clínica de Estomatología Pediátrica de la UATx, México. La población en estudio fue dividida en tres grupos: a experimental (n=30, b control (n=8, y c control negativo (n=29. Previo consentimiento informado se tomaron los índices de placa (LöeSilness 1967 e índice gingival en seis superficies; se midió el surco gingival con sonda periodontal y las coronas de acero cromo fueron evaluadas clínica y radiográficamente según su ajuste marginal y longitud cervical. Resultados: Los índices de placa y gingival no mostraron diferencias significativas para los grupos experimental y control negativo. El 34% de las coronas mostraron buen ajuste marginal, 33% un mal ajuste, 10.5% cortas, 7.9% largas y el 14% otro tipo de mal ajuste. La profundidad del surco gingival fue estadísticamente significativa para el primer y segundo molar inferior derechos y en los caninos inferiores (p >0.05; la superficie disto-vestibular presentó la mayor profundidad del surco gingival (2.34 mm, siendo estadísticamente significativa (p>0.05. Conclusiones: La profundidad del surco gingival fue mayor en los dientes rehabilitados con coronas de acero cromo mal ajustadas y sobre contorneadas (largas. La presencia de placa bacteriana y gingivitis estuvo relacionada con las coronas de acero cromo mal ajustadas.

  8. Erosion Behaviour of API X100 Pipeline Steel at Various Impact Angles and Particle Speeds

    Directory of Open Access Journals (Sweden)

    Paul C. Okonkwo

    2016-09-01

    Full Text Available Erosion is the gradual removal of material due to solid particle impingement and results in a failure of pipeline materials. In this study, a series of erosion tests were carried out to investigate the influence of particle speed and impact angle on the erosion mechanism of API X100 pipeline steel. A dry erosion machine was used as the test equipment, while the particle speed ranged from 20 to 80 m/s and impact angles of 30° and 90° were used as test parameters. The eroded API X100 steel surface was characterized using scanning electron microscope (SEM and X-ray photoelectron spectroscopy (XPS. The weight loss and erosion rate were also investigated. The results showed that at a 90° impact angle, a ploughing mechanism was occurring on the tested specimens, while material removal through low-angle cutting was the dominant mechanism at lower impact angles. Embedment of alumina particles on the target steel surface, micro-cutting, and low-angle cutting were observed at low impact angles. Therefore, the scratches, cuttings, and severe ploughings observed on some failed oil and gas pipelines could be attributed to the erosion mechanism.

  9. Características físico-químicas de amostras de méis de Apis mellifera L. do estado do Ceará, Brasil Physicochemical characteristics of Apis mellifera L. honey samples from the state of Ceará, Brazil

    Directory of Open Access Journals (Sweden)

    Augusta Carolina de Camargo Carmello Moreti

    2009-02-01

    Full Text Available Objetivou-se, na presente pesquisa, desenvolvida com amostras de méis de Apis mellifera coletadas diretamente dos produtores de diversos municípios do estado de Ceará, Brasil, verificar, com base em características físico-químicas, como se agrupam as amostras de méis. Dentre as 52 amostras de méis analisadas as que continham pólen de Serjania sp. como dominante ou acessório, formam um subgrupo distinto quanto aos caracteres físico-químicos, o que confirma que a origem floral interfere decisivamente nas características dos méis. Pela análise dos componentes principais, pôde-se verificar que os caracteres que mais influenciaram no agrupamento das amostras de méis foram acidez e índice de formol no eixo X e pH e cinzas no eixo Y.This paper was carried out to determine how the honey samples of the State of Ceará, Brazil may be grouped, based on the physicochemical composition of the honey. The samples were collected in different municipalities. Among the 52 honey samples analyzed it was observed that the samples which have Sejania sp. as dominant or accessory pollen form a different sub-group based on the physicochemical parameters. The results confirm that the honey bee composition is influenced by the plant nectar. The grouping of the honey samples was mostly influenced by acidity and formol index on the X axis, and pH and ashes, on the Y axis.

  10. Propiedades mecánicas del acero de refuerzo utilizado en Colombia Propiedades mecánicas del acero de refuerzo utilizado en Colombia

    OpenAIRE

    Victoria González Quintana; Juan Carlos Botero; Roberto Rochel; Julián Vidal; Martha Cecilia Alvarez Uribe

    2005-01-01

    Se presentan resultados del análisis estadístico aplicado al estudio experimental que de- termina las propiedades mecánicas de aceros colombianos sometidos a cargas monotónicas de tracción. Se obtienen curvas típicas de esfuerzo-deformación que permiten caracterizar aceros nacionales estudiados haciendo énfasis en las variables que determinan el cambio de comportamiento del materialA statistical analysis applied to a experimental study that determines the mechanical properties of steels produ...

  11. Estudio de microestructura y composición de la oxidación en vapor a 700 y 750oC de los aceros austeníticos AISI 304, 316 y 317

    Directory of Open Access Journals (Sweden)

    José Luddey Marulanda

    2013-01-01

    Full Text Available Se ha investigado la oxidación de los aceros inoxidables austeníticos AISI SAE: 304, 316 y 317; a temperaturas de 700 y 750oC, en una atmósfera próxima al 100% de vapor de agua, y de 10 a 1000h de exposición. La finalidad es comprobar la calidad de los aceros austeníticos y estudiar la morfología, composición y estructura de la fases de las capas formadas en la cascarilla del óxido de las muestras por Microscopía Electrónica de Barrido (SEM, Análisis de Rayos X por Dispersión de Energía (EDAX y Difracción de Rayos X (XRD, respectivamente. Así como también, se ha realizado a diferentes tiempos un estudio sistemático de termogravimetría de las muestras oxidadas, donde se ha observado que el acero AISI 304 presentó la menor ganancia de masa y el acero AISI 316 fue el de mayor de masa respecto a los tres aceros del trabajo. Adicionalmente fue realizado un estudio teórico de simulación termodinámica de oxidación en vapor de los tres aceros, en las mismas condiciones experimentales y mediante el programa Thermo-calc. En estos aceros oxidados se han comprobado la presencia de estructuras de fases de óxidos como: Fe2O3, espinelas protectoras Fe3O4 y Cr2NiO4, y óxidos mixtos de tipo (CrxFey2O3, (Fe,Cr,Mn3O4 y Ni6MnO8. Finalmente, se discute un posible mecanismo de la formación de las capas de óxidos de las muestras ensayadas.

  12. Comparative study in the induced corrosion by sulfate reducing microorganisms, in a stainless steel 304L sensitized and a carbon steel API X65; Estudio comparativo de la corrosion inducida por microorganismos sulfatorreductores, en un acero inoxidable 304L sensibilizado y un acero al carbono API X65

    Energy Technology Data Exchange (ETDEWEB)

    Diaz S, A.; Gonzalez F, E.; Arganis J, C.; Luna C, P.; Carapia M, L. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)]. e-mail: ads@nuclear.inin.mx

    2004-07-01

    In spite of the operational experience related with the presence of the phenomenon of microbiological corrosion (MIC) in industrial components, it was not but until the decade of the 80 s when the nuclear industry recognized its influence in some systems of Nuclear Generating Power plants. At the moment, diverse studies that have tried to explain the generation mechanism of this phenomenon exist; however, they are even important queries that to solve, especially those related with the particularities of the affected metallic substrates. Presently work, the electrochemical behavior of samples of stainless steel AISI 304L sensitized is evaluated and the carbon steel APIX65, before the action of sulfate reducing microorganisms low the same experimental conditions; found that for the APIX65 the presence of this type of bacteria promoted the formation of a stable biofilm that allowed the maintenance of the microorganisms that damaged the material in isolated places where stings were generated; while in the AISI 304L, it was not detected damage associated to the inoculated media. The techniques of Resistance to the Polarization and Tafel Extrapolation, allowed the calculation of the speed of uniform corrosion, parameter that doesn't seem to be influenced by the presence of the microorganisms; while that noise electrochemical it distinguished in real time, the effect of the sulfate reducing in the steel APIX65. (Author)

  13. Mejora de la calidad del acero obtenido por colada continua mediante influencias electrofísicas

    Directory of Open Access Journals (Sweden)

    Shklyar, V.

    1998-12-01

    Full Text Available Laboratory tests with tin smelted in a crucible and industrial tests with crude steel poured in moulds had been carried out. These metals were subjected to electrophysical influences. As a result of the applied electric field, it is observed in tin that during the solidification, the crystalization temperature and the solidification time are changed. Crystal growth in the electric field direction and an increase of the fracture limit in the steel ingot are observed.

    Se han realizado ensayos de laboratorio con estaño fundido en crisol y a escala industrial con acero líquido vertidos en moldes, sometiendo estos metales a influencias electrofísicas. Como resultado del campo aplicado, en el estaño se observa que durante la solidificación varía la temperatura de cristalización y el tiempo de solidificación. En el lingote de acero se observa un crecimiento de los cristales en dirección del campo eléctrico y un aumento del límite de rotura.

  14. X-ray polarimetry. [aboard Ariel 5 and OSO 8 for observation of galactic sources

    Science.gov (United States)

    Long, K. S.; Chanan, G. A.; Helfand, D. J.; Ku, W. H.-M.; Novick, R.

    1979-01-01

    The method by which the Bragg-crystal X-ray polarimeters aboard Ariel 5 and OSO 8 operate is briefly described, and some results obtained with these instruments for six Galactic X-ray sources are summarized. A precision measurement of the linear polarization in the Crab Nebula at energies of 2.6 and 5.2 keV is presented. Evidence is given for polarization in Sco X-1, Cyg X-2, Cen X-3, and the X-ray transient A0620-00. The determined or estimated polarizations are approximately 19.2% at 2.6 keV and 19.5% at 5.2 keV for the Crab Nebula, 1.1% at 2.6 keV and 2.4% at 5.2 keV for Sco X-1, 2.5% at 2.6 keV and 9.8% at 5.2 keV for Cyg X-1, an upper limit of 13.5% for A0620-00, an upper limit of 13.5% to the time-averaged polarization of Cen X-3, and an apparent value of about 5% for Cyg X-2.

  15. Correction factors for safe performance of API X65 pipeline steel

    International Nuclear Information System (INIS)

    Hashemi, Sayyed H.

    2009-01-01

    Prediction of required Charpy energy for fracture arrest is vital for safe performance of gas transportation pipelines. This is commonly estimated through failure models calibrated in the past on fracture data from combined Charpy tests and full-thickness burst experiments. Unfortunately, such pipeline failure models are unable to correctly predict the minimum arrest toughness of thermo-mechanical controlled rolled (TMCR) steels. To refine the existing failure models, different empirical adjustments have been proposed in recent years. In this paper, similar correction factors were derived from fracture information of instrumented Charpy impact tests on API X65 steel. The contribution of different fracture mechanisms of impact test specimens was determined through energy partitioning analysis. Parts of the energy contribution were correlated then to the source of uncertainty observed in similar experiments. The applied technique was similar to that of previous studies on X70 and X100 steels, and proved to be encouraging in giving consistent results compared to available test data.

  16. Uma breve revisão histórica do desenvolvimento da soldagem dos aços API para tubulações A brief history review of development on API steels welding for pipeline

    Directory of Open Access Journals (Sweden)

    Jaime Casanova Soeiro Junior

    2013-06-01

    Full Text Available Este trabalho enfoca o desenvolvimento dos aços API para tubulações desde o aço API 5L X42, desenvolvido em 1948, através de laminação a quente seguida de tratamento térmico. Desde então foram feitos diferentes desenvolvimentos visando aumentar a resistência mecânica e a tenacidade, além de melhorar a soldabilidade. Entre eles, a adição de elementos de liga, produzindo os aços ARBL e a utilização de rotas de processamento termomecânico durante a laminação. Inicialmente a rota utilizada era a laminação a quente controlada (TMCR, com utilização de elemento microligante como Nb para os aços X60 e o conjunto Nb e V para os aços X65 e X70, associado a uma redução do teor de carbono. Posteriormente foi implantada a rota de fabricação do aço por laminação controlada seguida de resfriamento controlado (TMCP, com redução de carbono e adição de Nb e Ti para os aços X80, e adições de Mo, Nb, Be Ti para os X100. A redução do carbono foi motivada também para melhorar a sua soldabilidade e, por este motivo, estes aços são soldados por diferentes processos de soldagem, como o eletrodo revestido. Desenvolvimentos recentes com raiz feita com MAG-TC e enchimento com arame tubular tem dado resultados animadores.This paper is a brief history on the development of pipelines steels since the API 5L X42 steel, developed in 1948 by hot rolling followed by heat treatment. Subsequently different developments were made to increase the strength and toughness of these materials, and to improve their weldability. Among them, the addition of microalloying elements, producing HSLA steels and thermomechanical processing routes during hot rolling. Initially the route used was the controlled hot rolling (TMCR, together with microalloying element such as Nb for X60 steel and Nb plus V for X65 and X70 steels, associated with a reduction in carbon content. Later, the thermomechanical controlled process (TMCP manufacturing route was

  17. Métodos para atrair a abelha Apis mellifera L. em cultura de abacate (Persea americana Mill. Methods to attract honeybee Apis mellifera L. to avocado tree (Persea americana Mill

    Directory of Open Access Journals (Sweden)

    Darclet Terezinha Malerbo Souza

    2002-04-01

    Full Text Available O presente experimento teve como objetivo avaliar métodos de atração da abelha Apis mellifera L. (Hymenoptera, Apidae em duas variedades de abacate (Persea americana Mill.. Os atrativos utilizados foram extratos de Cymbopogon citratus, Ocimum basilicum, Lippia alba, folha de Citrus sp, folha de Eucaliptus sp. e o eugenol e o linalol (SIGMA. Os tratamentos utilizados foram: coberto; descoberto pulverizado (DP; descoberto com tubos e descoberto não pulverizado (DNP. Observou-se que a atratividade das substâncias testadas desapareceu minutos após a sua aplicação, utilizando ou não a glicerina, em ambas as variedades. A pulverização dos extratos de falsa melissa, folhas de eucalipto e folhas de laranja apresentaram um aumento no número de abelhas Apis mellifera, na variedade Quintal. Os dados mostraram que a freqüência das abelhas A. mellifera foi maior na variedade Quintal comparada à variedade Fortuna. Isto pode ter ocorrido devido à maior concentração de açúcares do néctar de suas flores. Observou-se que as abelhas A. mellifera preferiram visitar as flores do abacateiro da variedade Quintal, tanto para néctar quanto para coleta de pólen, comparada à variedade Fortuna. Com relação aos frutos, nenhuma das características apresentou diferença significativa entre os tratamentos, em ambas as variedades. Entretanto, observou-se que na variedade Quintal os frutos decorrentes dos tratamentos DP e DNP foram mais pesados, mais compridos e com maior espessura da polpa, comparados ao único fruto obtido do tratamento coberto. Os produtos testados em tubos não foram eficientes para atrair a abelha Apis mellifera, em ambas as variedades.The present experiment was carried out to evaluate some methods to attract honeybee Apis mellifera L. (Hymenoptera, Apidae to two avocado varieties (Persea americana Mill.. Extracts of Cymbopogon citratus, Ocimum basilicum, Lippia alba, Citrus sp leaf, Eucalyptus sp leaf, the eugenol and linalol

  18. Testing of the structure of macromolecular polymer films containing solid active pharmaceutical ingredient (API) particles

    International Nuclear Information System (INIS)

    Boelcskei, E.; Suevegh, K.; Marek, T.; Regdon, G.; Pintye-Hodi, K.

    2011-01-01

    The aim of the present study was to investigate the structure of free films of Eudragit L 30D-55 containing different concentrations (0%, 1% or 5%) of diclofenac sodium by positron annihilation spectroscopy. The data revealed that the size of the free-volume holes and the lifetimes of ortho-positronium atoms decreased with increase of the API concentration. Films containing 5% of the API exhibited a different behavior during storage (17 o C, 65% relative humidity (RH)) in consequence of the uptake of water from the air. -- Highlights: → The aim of the present study was to investigate the structure of free films of Eudragit L 30D-55 containing different concentrations (0%, 1% or 5%) of diclofenac sodium by positron annihilation spectroscopy. → The data revealed that the size of the free-volume holes and the lifetimes of ortho-positronium atoms decreased with increase of the API concentration (). → The API distorts the original polymer structure, but as time goes by, the metastable structure relaxes and it is almost totally restored after 3 weeks of storage (17 o C, 65% RH).

  19. Android quick APIs reference

    CERN Document Server

    Cinar, Onur

    2015-01-01

    The Android Quick APIs Reference is a condensed code and APIs reference for the new Google Android 5.0 SDK. It presents the essential Android APIs in a well-organized format that can be used as a handy reference. You won't find any technical jargon, bloated samples, drawn out history lessons, or witty stories in this book. What you will find is a software development kit and APIs reference that is concise, to the point and highly accessible. The book is packed with useful information and is a must-have for any mobile or Android app developer or programmer. In the Android Quick APIs Refe

  20. Complete genome sequences and comparative genome analysis of Lactobacillus plantarum strain 5-2 isolated from fermented soybean.

    Science.gov (United States)

    Liu, Chen-Jian; Wang, Rui; Gong, Fu-Ming; Liu, Xiao-Feng; Zheng, Hua-Jun; Luo, Yi-Yong; Li, Xiao-Ran

    2015-12-01

    Lactobacillus plantarum is an important probiotic and is mostly isolated from fermented foods. We sequenced the genome of L. plantarum strain 5-2, which was derived from fermented soybean isolated from Yunnan province, China. The strain was determined to contain 3114 genes. Fourteen complete insertion sequence (IS) elements were found in 5-2 chromosome. There were 24 DNA replication proteins and 76 DNA repair proteins in the 5-2 genome. Consistent with the classification of L. plantarum as a facultative heterofermentative lactobacillus, the 5-2 genome encodes key enzymes required for the EMP (Embden-Meyerhof-Parnas) and phosphoketolase (PK) pathways. Several components of the secretion machinery are found in the 5-2 genome, which was compared with L. plantarum ST-III, JDM1 and WCFS1. Most of the specific proteins in the four genomes appeared to be related to their prophage elements. Copyright © 2015 Elsevier Inc. All rights reserved.

  1. Diaquabis[5-(2-pyridyltetrazolato-κ2N1,N5]iron(II

    Directory of Open Access Journals (Sweden)

    Min Hu

    2009-04-01

    Full Text Available The title complex, [Fe(C6H4N52(H2O2], was synthesized by the reaction of ferrous sulfate with 5-(2-pyridyl-2H-tetrazole (HL. The FeII atom, located on a crystallographic center of inversion, is coordinated by four N-atom donors from two planar trans-related deprotonated L ligands and two O atoms from two axial water molecules in a distorted octahedral geometry. The FeII mononuclear units are further connected by intermolecular O—H...N and C—H...O hydrogen-bonding interactions, forming a three-dimensional framework.

  2. Métodos electroquímicos semicuantitativos de estudio de lo corrosión por picaduras del acero para armaduras de hormigón

    Directory of Open Access Journals (Sweden)

    Andrade Perdrix, M. C.

    1977-12-01

    Full Text Available El acero embebido en el hormigón se encuentra sometido a un medio de elevada alcalinidad (pH comprendido entre 12 y 13, debido a la cal libre, a los álcalis que contiene el cemento, y al Ca(0H2 que se forma durante la hidratación de los silicatos. En esta situación, el acero se halla recubierto por una capa de óxidos e hidróxidos estables que lo mantienen pasivado, interponiendo una barrera entre él y los agentes agresivos.

  3. 10 CFR 52.5 - Employee protection.

    Science.gov (United States)

    2010-01-01

    ... adverse action occurs because the employee has engaged in protected activities. An employee's engagement... 10 Energy 2 2010-01-01 2010-01-01 false Employee protection. 52.5 Section 52.5 Energy NUCLEAR... Provisions § 52.5 Employee protection. (a) Discrimination by a Commission licensee, holder of a standard...

  4. Ductile failure analysis of API X65 pipes with notch-type defects using a local fracture criterion

    International Nuclear Information System (INIS)

    Oh, Chang-Kyun; Kim, Yun-Jae; Baek, Jong-Hyun; Kim, Young-Pyo; Kim, Woo-Sik

    2007-01-01

    A local failure criterion for API X65 steel is applied to predict ductile failure of full-scale API X65 pipes with simulated corrosion and gouge defects under internal pressure. The local failure criterion is the stress-modified fracture strain as a function of the stress triaxiality (defined by the ratio of the hydrostatic stress to the effective stress). Based on detailed finite element (FE) analyses with the proposed local failure criterion, burst pressures of defective pipes are estimated and compared with experimental data. For pipes with simulated corrosion defects, FE analysis with the proposed local fracture criterion indicates that predicted failure takes place after the defective pipes attain maximum loads for all cases, possibly due to the fact that the material has sufficient ductility. For pipes with simulated gouge defects, on the other hand, it is found that predicted failure takes place before global instability, and the predicted burst pressures are in good agreement with experimental data, providing confidence in the present approach

  5. 27 CFR 5.2 - Related regulations.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Related regulations. 5.2 Section 5.2 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF DISTILLED SPIRITS Scope § 5.2 Related regulations...

  6. Study of an API migration for two XML APIs

    NARCIS (Netherlands)

    T.T. Bartholomei; K. Czarnecki; R. Lämmel (Ralf); T. van der Storm (Tijs); M.G.J. van den Brand (Mark); D. Gasevic; J. Gray

    2010-01-01

    htmlabstractAPI migration refers to adapting an application such that its dependence on a given API (the source API) is eliminated in favor of depending on an alternative API (the target API) with the source and target APIs serving the same domain. One may attempt to automate API migration by code

  7. Acute 5-(2-aminopropyl)benzofuran (5-APB) intoxication and fatality: a case report with postmortem concentrations.

    Science.gov (United States)

    McIntyre, Iain M; Gary, Ray D; Trochta, Amber; Stolberg, Susan; Stabley, Robert

    2015-03-01

    A 20-year-old man, a college student, became unresponsive in front of his girlfriend. He was known to consume alcohol and take an unknown drug at some point while in attendance at a local music festival earlier in the day/evening. Upon arrival of emergency personnel, he was noted to be asystolic and apneic. Despite aggressive medical intervention by emergency personnel and at a local hospital emergency room, he was pronounced deceased within 1.25 h of initial medical attention. Postmortem blood initially screened positive for methamphetamine by ELISA. An alkaline drug screen detected 5-(2-aminopropyl)benzofuran (5-APB) which was subsequently confirmed and quantified by a specific GC-MS SIM analysis following solid-phase extraction. Concentrations were determined in the peripheral blood (2.5 mg/L), central blood (2.9 mg/L), liver (16 mg/kg), vitreous (1.3 mg/L), urine (23 mg/L) and gastric contents (6 mg). No other common amphetamine-like compound was detected, although 5-(2-aminopropyl)-2,3-dihydrobenzofuran (5-APDB) was presumptively identified in both peripheral blood and urine. Alcohol, the only other drug identified, was confirmed at a concentration of 0.02% (w/v). © The Author 2014. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  8. 39 CFR 5.2 - Committee procedure.

    Science.gov (United States)

    2010-07-01

    ... 39 Postal Service 1 2010-07-01 2010-07-01 false Committee procedure. 5.2 Section 5.2 Postal Service UNITED STATES POSTAL SERVICE THE BOARD OF GOVERNORS OF THE U.S. POSTAL SERVICE COMMITTEES (ARTICLE V) § 5.2 Committee procedure. Each committee establishes its own rules of procedure, consistent with...

  9. Influencia de la transformación austenita-martensita en la estabilidad dimensional de un nuevo acero para herramientas aleado con niobio (0,08% y vanadio (0,12%

    Directory of Open Access Journals (Sweden)

    Conejero Ortega, Gerardo

    2014-09-01

    Full Text Available Austenite-martensite transformation influence on the dimensional stability of a new experimental tool steel alloyed with niobium (0.08% wt. and vanadium (0.12% wt. has been studied. The dimensional stability of this new steel was compared with the dimensional stability of commercial steel, after and before two thermal treatments, T1 (860 °C and T2 (900 °C. The thermal treatments consisted on heating and cooling, at 1 atmosphere of pressure, in N2 atmosphere furnace, fol lowing by heating in a conventional furnace at 180 °C during 1 hour. Initially, the experimental steel composition and Ac1 and Ac3 transformation temperatures were determined by glow-discharge luminescence (GDL and dilatometric tests, respectively, in order to select the austenization temperatures of T1 and T2 treatments. After hardness measurement, the microstructure of both steels was characterized by X-Ray Diffraction (XRD and optical metallography, before and after of T1 and T2 thermal treatments. Finally, longitudinal and angular dimensional stability analyses were realized for both commercial and experimental steels. After a contrastive hypothesis analysis, the results showed that the longitudinal relative variation of the experimental steel calculated was around 0.2% and the angular relative variation was not significantSe ha estudiado la influencia de la transformación de austenita a martensita en la estabilidad dimensional de un acero experimental para herramientas aleado con niobio (0,08% en peso y vanadio (0,12% en peso. La estabilidad dimensional del acero experimental fue comparada con la de un acero comercial antes y después de ser sometidos, ambos aceros, a dos tratamientos térmicos diferentes. Los tratamientos térmicos consistieron en un calentamiento y mantenimiento durante una hora a temperaturas de 860 °C (T1 y 900 °C (T2 y un enfriamiento final en horno con nitrógeno (N2 a 1 atmósfera de presión. Inicialmente, se determinaron las composiciones del

  10. API manager implementation and its use for Indus accelerator control

    International Nuclear Information System (INIS)

    Merh, B.N.; Agrawal, R.K.; Barpande, K.; Fatnani, P.; Navathe, C.P.

    2012-01-01

    The control system software needed for operation of Indus accelerators is coupled to the underlying firmware and hardware of the control system by the Application Programming Interface (API) manager. In the three layered architecture of Indus control system, PVSS-II SCADA is being used at the layer-1(L1) for control and monitoring of various sub-systems. The layer-2(L2) consists of VME bus based system. The API manager plays a crucial role in interfacing the L1 and L2 of the control system. It has to interact with both the PVSS database and the L2. In order to access the PVSS database it uses the PVSS API, a C++ class library, whereas in order to access the L2 custom functions have been built. Several other custom functionalities have also been implemented. The paper presents the important aspects of the API manager like its implementation, its interface mechanism to the lower layer and features like configurability, reusable classes, multithreading capability etc. (author)

  11. Tratamientos térmicos de los aceros sinterizados obtenidos a partir de polvos prealeados Fe-1,5% Mo

    Directory of Open Access Journals (Sweden)

    Torralba, J. M.

    1995-04-01

    Full Text Available The influence of several heat treatments on the mechanical and physical properties of three different sintered Ni-Cu-Mo alloyed steels are evaluated. The heat treatments carried out were quenching and tempering at different temperatures. The raw material studied was a Fe-Mo prealloyed powder with an 1.5% Mo content.

    Se estudia la influencia que distintos estados de tratamiento térmico ejercen sobre las propiedades mecánicas y físicas de tres aceros aleados con cobre, níquel y molibdeno sinterizados. Los tratamientos térmicos realizados consisten en temple y revenido a distintas temperaturas. El material de partida utilizado para conseguir la aleación de molibdeno ha sido un polvo prealeado de Fe-1,5% Mo.

  12. Testing of the structure of macromolecular polymer films containing solid active pharmaceutical ingredient (API) particles

    Energy Technology Data Exchange (ETDEWEB)

    Boelcskei, E. [Department of Pharmaceutical Technology, University of Szeged, H-6720 Szeged, Eoetvoes u. 6 (Hungary); Suevegh, K. [Laboratory of Nuclear Chemistry, Eoetvoes Lorand University, H-1518 Budapest 112, P.O. Box 32 (Hungary); Marek, T. [Hungarian Academy of Sciences, Research Group for Nuclear Techniques in Structural Chemistry, Eoetvoes Lorand University, H-1518 Budapest 112, P.O. Box 32 (Hungary); Regdon, G. [Department of Pharmaceutical Technology, University of Szeged, H-6720 Szeged, Eoetvoes u. 6 (Hungary); Pintye-Hodi, K., E-mail: klara.hodi@pharm.u-szeged.h [Department of Pharmaceutical Technology, University of Szeged, H-6720 Szeged, Eoetvoes u. 6 (Hungary)

    2011-07-15

    The aim of the present study was to investigate the structure of free films of Eudragit{sup L} 30D-55 containing different concentrations (0%, 1% or 5%) of diclofenac sodium by positron annihilation spectroscopy. The data revealed that the size of the free-volume holes and the lifetimes of ortho-positronium atoms decreased with increase of the API concentration. Films containing 5% of the API exhibited a different behavior during storage (17 {sup o}C, 65% relative humidity (RH)) in consequence of the uptake of water from the air. -- Highlights: {yields} The aim of the present study was to investigate the structure of free films of Eudragit{sup L} 30D-55 containing different concentrations (0%, 1% or 5%) of diclofenac sodium by positron annihilation spectroscopy. {yields} The data revealed that the size of the free-volume holes and the lifetimes of ortho-positronium atoms decreased with increase of the API concentration (). {yields} The API distorts the original polymer structure, but as time goes by, the metastable structure relaxes and it is almost totally restored after 3 weeks of storage (17 {sup o}C, 65% RH).

  13. The development, validity, and reliability of the Addiction Profile Index (API).

    Science.gov (United States)

    Ögel, Kültegin; Evren, Cüneyt; Karadağ, Figen; Gürol, Defne Tamar

    2012-01-01

    The objective of this study was to develop a practical questionnaire for multidimensional assessment of problems associated with alcohol and substance abuse that would also be useful for treatment planning. The Addiction Profile Index (API) is a self-report questionnaire consisting of 37 items and the following 5 subscales: characteristics of substance use; dependency diagnosis; the effects of subsance use on the user; craving; motivation to quit using substances. The study included 345 alcohol and/or substance abusers from 2 addiction treatment clinics and a prison addiction service. The validity of the questionnaire was assessed using the Michigan Alcoholism Screening Test (MAST), Readiness to Change Questionnaire (SOCRATES), Penn Alcohol Craving Scale (PACS), Drug Craving Scale (DCS), Structured Clinical Interview for DSM-IV Axis I Disorders (SCID-I), and Addiction Severity Index (ASI). The Cronbach's alpha coefficient for the total API was 0.89 and for the subscales it ranged from 0.63 to 0.86. Item-total correlation coefficients ranged from 0.42 to 0.89. The Spearman Brown split-half method coefficient for the total API was 0.83. In all, 4 factors were obtained using explanatory factor analysis that represented 52.3% of the total variance. The API craving subscale was observed to be consistent with PACS and the API motivation subscale was consistent with SOCRATES. The API total score was strongly correlated with the mean MAST score, and the composite ASI medical status, substance use, legal status, and family social relations subscale scores. Based on ROC analyses, the area under curve was 0.90. With a total API cut-off score of 4, the scale's sensitivity and specificity 0.85 was 0.78, respectively. The findings show that the API is a valid and reliable questionnaire that can be used to measure the severity of different dimensions of substance dependency.

  14. A method for designing fiberglass sucker-rod strings with API RP 11L

    International Nuclear Information System (INIS)

    Jennings, J.W.; Laine, R.E.

    1991-01-01

    This paper presents a method for using the API recommended practice for the design of sucker-rod pumping systems with fiberglass composite rod strings. The API method is useful for obtaining quick, approximate, preliminary design calculations. Equations for calculating all the composite material factors needed in the API calculations are given

  15. APIs

    CERN Document Server

    Jacobson, Daniel; Woods, Dan

    2011-01-01

    Programmers used to be the only people excited about APIs, but now a growing number of companies see them as a hot new product channel. This concise guide describes the tremendous business potential of APIs, and demonstrates how you can use them to provide valuable services to clients, partners, or the public via the Internet. You'll learn all the steps necessary for building a cohesive API business strategy from experts in the trenches. Facebook and Twitter APIs continue to be extremely successful, and many other companies find that API demand greatly exceeds website traffic. This book offe

  16. Social Reinforcement Delays in Free-Flying Honey Bees (Apis mellifera L.)

    Science.gov (United States)

    Craig, David Philip Arthur; Grice, James W.; Varnon, Chris A.; Gibson, B.; Sokolowski, Michel B. C.; Abramson, Charles I.

    2012-01-01

    Free-flying honey bees (Apis mellifera L.) reactions were observed when presented with varying schedules of post-reinforcement delays of 0 s, 300 s, or 600 s. We measured inter-visit-interval, response length, inter-response-time, and response rate. Honey bees exposed to these post-reinforcement delay intervals exhibit one of several patterns compared to groups not encountering delays, and had longer inter-visit-intervals. We observed no group differences in inter-response time. Honey bees with higher response rates tended to not finish the experiment. The removal of the delay intervals increased response rates for those subjects that completed the trials. PMID:23056425

  17. Procesos de conversión de acero y efecto de variables en convertidores tipo L.B.E.

    Directory of Open Access Journals (Sweden)

    Blanco, C.

    1995-10-01

    Full Text Available In order to determine control equations based on qualitative and quantitative changes of the raw materials, an analysis of the efficiency of the steel production process was carried out in converters under specified operation conditions. Empirical equations to obtain the final composition of the steel as a function of the additives, the initial concentrations of the hot metal and the blowing oxygen patterns are established. The resulting relationships depend on the considered variables and therefore could be used to determine operational strategies in order to obtain steels of a certain quality.

    Se analiza la eficacia de los procesos de transformación en convertidores en condiciones de trabajo determinadas, para deducir relaciones aplicables al control basadas en la modificación de cantidades y composiciones de las materias primas. Se plantean ecuaciones empíricas para determinar la composición final del acero como función de los aditivos y de las concentraciones iniciales del arrabio tratado, así como el patrón de soplado de oxígeno. Las relaciones obtenidas establecen las dependencias entre cada una de las variables consideradas y, por tanto, permiten determinar estrategias de operación para obtener aceros con unas calidades finales dadas.

  18. Mimotopes for Api g 5, a Relevant Cross-reactive Allergen, in the Celery-Mugwort-Birch-Spice Syndrome.

    Science.gov (United States)

    Lukschal, Anna; Wallmann, Julia; Bublin, Merima; Hofstetter, Gerlinde; Mothes-Luksch, Nadine; Breiteneder, Heimo; Pali-Schöll, Isabella; Jensen-Jarolim, Erika

    2016-03-01

    In the celery-mugwort-birch-spice syndrome, a significant proportion of IgE is directed against high molecular weight (HMW) glycoproteins, including the celery allergen Api g 5. BIP3, a monoclonal antibody originally raised against birch pollen, recognizes HMW allergens in birch and mugwort pollens, celery, and Apiaceae spices. Our aim was to generate mimotopes using BIP3 for immunization against the HMW allergens relevant in the celery-mugwort-birch-spice cross reactivity syndrome. Mimotopes were selected from a random-peptide display library by BIP3 and applied in IgE inhibition assays. The 3 phage clones with the highest inhibitory capacity were chosen for immunization of BALB/c mice. Mouse immune sera were tested for IgG binding to blotted birch pollen extract and used for inhibiting patients' IgE binding. Furthermore, sera were tested for binding to Api g 5, to horseradish peroxidase (HRP) as a second glycoprotein, or to non-glycosylated control allergen Phl p 5 in ELISA, and the specific Api g 5-specific IgG titers were determined. Three rounds of biopanning resulted in phage clones exhibiting 7 different sequences including 1 dominant, 1-6-cyclo-CHKLRCDKAIA. Three phage clones had the capacity to inhibit human IgE binding and induced IgG to the HMW antigen when used for immunizing BALB/c mice. The induced BIP3-mimotope IgG reached titers of 1:500 specifically to Api g 5, but hardly reacted to glycoprotein HRP, revealing a minor role of carbohydrates in their epitope. The mimotopes characterized in this study mimic the epitope of BIP3 relevant for Api g 5, one of the cross-reactive HMW allergens relevant in the celery-mugwort-birch-spice syndrome. BIP3 mimotopes may be used in the future for hyposensitization in this clinical syndrome by virtue of good and specific immunogenicity.

  19. Mecanismos de fractura a alta temperatura en aceros eléctricos no-orientados

    Directory of Open Access Journals (Sweden)

    García-Sánchez, E. O.

    2007-08-01

    Full Text Available In this research work the effect of deformation temperature on the hot ductility of non-oriented electrical steels (0.6 % Si-0.3 Al % was studied using high temperature tensile tests. The specimens were machined from two thin slabs (50 mm thickness produced by CSP process (Compact Strip Process, one of them using 100 % sponge iron and the other using 67 % scrap and 33 % sponge iron. The tensile tests were carried out at constant strain rate (5×1010–4 s–1, and a temperature range from 850 to 1,200 °C. The results showed that the ductility decreased with the increment in the temperature until approximately 1,000 °C. At higher temperatures, a ductility recovery was observed only in the steel fabricated without scrap. Scanning Electron Microscopy on fracture surfaces showed that the loss of ductility is associated with intergranular cracking promoted by the austenitic transformation and AlN grain boundaries precipitation.

    Se investigó el efecto de la temperatura de deformación sobre la ductilidad de aceros eléctricos de grano no-orientado (0,6 % Si-0,3 % Al mediante ensayos de tracción uniaxial. Las probetas se obtuvieron de planchones delgados (50 mm de espesor tipo CSP (Continuous Strip Processing fabricados a partir de 100 % hierro esponja y una mezcla de 67 % chatarra y 33 % de hierro esponja. El rango de temperatura de estudio fue de 850 a 1.200 °C y los ensayos se llevaron a cabo a una velocidad de deformación constante de 5×10–4 s–1. Los resultados experimentales demostraron que la ductilidad (% RA disminuye con el aumento en la temperatura hasta un mínimo a ~1.000 °C. A temperaturas mayores, la ductilidad del acero fabricado a partir de 100 % hierro esponja se recupera. Este efecto no fue observado en el acero fabricado a partir de chatarra. La caracterización de las superficies de fractura mediante microscopía electrónica de barrido demostró que la pérdida de

  20. Infestação do ácaro Varroa destructor em colônias de abelhas africanizadas (Apis mellifera L. no Semiárido potiguar, Nordeste do Brasil

    Directory of Open Access Journals (Sweden)

    Stephano Bismark Lopes Cavalcante Moreira

    2017-02-01

    Full Text Available O presente trabalho teve como objetivo analisar os índices de infestação pelo ácaro Varroa. destructor em colônias de abelhas africanizadas (Apis mellifera de apiários dos municípios de Encanto e de Marcelino Vieira, estado do Rio Grande do Norte. A pesquisa foi conduzida no período de setembro a dezembro de 2014, sendo coletadas em média de 100 a 200 abelhas adultas (nutrizes retiradas dos quadros centrais do ninho com crias de cada colmeia, aprisionadas em recipientes contendo 100 mL de álcool a 70% e encaminhadas para laboratório do Instituto Federal do Rio Grande do Norte (IFRN, para a contagem das abelhas e dos ácaros. Os resultados apresentaram ocorrência do ácaro V. destructor em todos apiários e em todas colmeias analisados, obtendo uma infestação média de 7,24% em Encanto e de 5,25% em Marcelino Vieira, níveis de infestação baixos (<15%, portanto, não acarretando risco às colônias.Varroa destructor mite infestation in colonies of Africanized honey bees (Apis mellifera L. in the potiguar Semi-arid region, Northeastern BrazilAbstract: The goal of the present work was to analyze the rates of infestation by Varroa. destructor mite in Africanized honeybees (Apis mellifera colonies from apiaries in Encanto and Marcelino Vieira cities, state of Rio Grande do Norte. The research was conducted during the period from September to December 2014. In average 100 to 200 adult bees (nursing honey bee workers were collected from the brood chamber over center frames of with brood of each hive surveyed, trapped in containers containing 100 mL of 70% alcohol and sent to the laboratory of the Federal Institute of Rio Grande do Norte (IFRN for the counting of bees and mites. The results showed an occurrence of the Varroa destructor mite in all apiaries and in all hives analyzed, obtaining an average infestation of 7.24% in Encanto city and 5.25% in Marcelino Vieira city, low infestation levels (<15%, without risk to the colonies.

  1. Comportamiento parabólico del crecimiento de capas boradas en los aceros Y8A y X12M // Parabolic behavior of boriding layers growth in Y8A and X12M steels

    Directory of Open Access Journals (Sweden)

    C. Figueroa Hernández

    1999-01-01

    Full Text Available Se determina la influencia que tienen los principales parámetros tecnológicos del borado en el crecimiento de las capas y secorrobora el cumplimiento de la ley parabólica para predecir este comportamiento en los aceros Y8A y X12M.El proceso de borado se aplica en una mezcla de carburo de silicio y bórax (70 y 30 % a la temperatura de 850, 900 y 950 oCdurante un tiempo de 2, 4 y 6 horas. Como variable dependiente se seleccionó la profundidad del recubrimiento, a partir de lacual se obtuvieron los coeficientes del crecimiento parabólico y la energía de activación en función de la temperatura, el tiempodel proceso y el tipo de acero.La caracterización metalográfica reveló la presencia de la fase Fe2BPalabras claves: Borado, recubrimiento superf icial , t ecnología de recubrimiento.__________________________________________________________________________AbstractIt was determined the influence of the main technological parameters of the boriding process, and a mathematical model thatallows to predict this conduct on the steels Y8A and X12M steels was obtained.The boriding process is applied in a mixture of silicon carbide and borax (70 and 30% at 850, 900 and 950 oC temperatureduring a period of time 2, 4 and 6 hours. As an independent variable the depth of the coat was selected.It was obtained the parabolic growth coefficients, and the activation energy according to temperature, time and the chemicalcomposition of steel.Metallografic analysis reveals the presence of Fe2B phase.Key words: Boriding process, superf icial coat , coat technology.

  2. Behavioral studies of learning in the Africanized honey bee (Apis mellifera L.).

    Science.gov (United States)

    Abramson, Charles I; Aquino, Italo S

    2002-01-01

    Experiments on basic classical conditioning phenomena in adult and young Africanized honey bees (Apis mellifera L.) are described. Phenomena include conditioning to various stimuli, extinction (both unpaired and CS only), conditioned inhibition, color and odor discrimination. In addition to work on basic phenomena, experiments on practical applications of conditioning methodology are illustrated with studies demonstrating the effects of insecticides on learning and the reaction of bees to consumer products. Electron microscope photos are presented of Africanized workers, drones, and queen bees. Possible sub-species differences between Africanized and European bees are discussed. Copyright 2002 S. Karger AG, Basel

  3. Beehold : the colony of the honeybee (Apis mellifera L) as a bio-sampler for pollutants and plant pathogens

    NARCIS (Netherlands)

    Steen, van der J.J.M.

    2016-01-01

    Bio-sampling is a function of bio-indication. Bio-indication with honeybee colonies (Apis mellifera L) is where the research fields of environmental technology and apiculture overlap. The honeybees are samplers of the environment by collecting unintentionally and simultaneously, along

  4. Propiedades mecánicas del acero de refuerzo utilizado en Colombia Propiedades mecánicas del acero de refuerzo utilizado en Colombia

    Directory of Open Access Journals (Sweden)

    Victoria González Quintana

    2005-04-01

    Full Text Available Se presentan resultados del análisis estadístico aplicado al estudio experimental que de- termina las propiedades mecánicas de aceros colombianos sometidos a cargas monotónicas de tracción. Se obtienen curvas típicas de esfuerzo-deformación que permiten caracterizar aceros nacionales estudiados haciendo énfasis en las variables que determinan el cambio de comportamiento del materialA statistical analysis applied to a experimental study that determines the mechanical properties of steels produced in Colombia subjected to monotonic loads of tension is presented. Typical stress-strain diagram that allow to characterize these steels making emphasis in the variables that determine the change of behaviour of the materia are presented.

  5. PROTECCIÓN CONTRA LA CORROSIÓN POR SALES FUNDIDAS DE UN ACERO AL CARBONO POR ROCIADO TERMICO

    OpenAIRE

    JOSE MARULANDA; ANDRÉS GARCÍA; JOSE VITOLA

    2009-01-01

    Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono rociado térmicamente con una aleación de acero inoxidable, en una mezcla de sal con 20% Na2SO4 - 80% V2O5, entre 700ºC - 850ºC. Los resultados de las pruebas gravimétricas mostraron una deficiente protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento protector, debido a que las temperaturas de exposición fueron mayores que las temperaturas de fusión de...

  6. Experience API: Flexible, Decentralized and Activity-Centric Data Collection

    Science.gov (United States)

    Kevan, Jonathan M.; Ryan, Paul R.

    2016-01-01

    This emerging technology report describes the Experience API (xAPI), a new e-learning specification designed to support the learning community in standardizing and collecting both formal and informal distributed learning activities. Informed by Activity Theory, a framework aligned with constructivism, data is collected in the form of activity…

  7. Corrosion resistance of API 5L grade B steel with taro leaf (Colocasia esculenta) addition as corrosion inhibitor in HCl 0.1 M

    Science.gov (United States)

    Lestari, Yulinda; Priyotomo, Gadang

    2018-05-01

    Taro leaf (Colocasia esculenta) has the potential to be used as a corrosion inhibitor because it has a substance called polyphenol that binds to the hydroxyl group and essential amino acids. Taro leaf extract is taken by maceration method. In this study, the specimen was steel API 5L grade B that would measured the corosivity in 0.1 M HCl solution + taro leaf extract with a specific concentration (in ppm). Tests conducted by FTIR method taro leaves, potentiodynamic polarization (Tafel) and Electrochemical Impedance Spectroscopy (EIS). Based on the results revealed that there is a phenolic group in taro leaves, which has polyphenol content 0.053 % (mg/100 mg). The optimum composition of taro leaf extract is 4000 ppm which generate corrosion rate value of 30.22 mpy and efficiency inhibitor performance of 72.7 %. In this study, the Kads value of taro leaf extract ranged from 0.885 to greater than Kads value of ginger extract in hydrochloric acid solution. The high Kads values indicate a more efficient process of adsorption and better value of inhibition efficiency.

  8. Broken SU(5) x SU(5) chiral symmetry and the classification of B mesons

    International Nuclear Information System (INIS)

    Hatzis, M.

    1984-01-01

    We consider broken SU(5) x SU(5) chiral summetry and we assume that the vacuum is SU(5)-symmetric. Using the observed mass spectrum of pseudoscalar mesons, and setting the bu mass in the range 5.2 +- 0.06 GeV, we predict the masses of bs, bc, and etasub(b) states as well as axial current couplings fsub(i)/fsub(π). SU(5) x SU(5) is found to be consistent with SU(4) x SU(4) breaking. The problem of eta - eta' - eta sub(c) - eta sub(b) mixing is also discussed

  9. Hexagonal perovskites with cationic vacancies. 25. Hexagonal 5 L stacking polytypes in the systems Ba/sub 5/BaWsub(3-x)sup(VI)Msub(x)sup(V)vacantOsub(15-x/2)vacantsub(x/2) with Msup(V) = Nb, Ta

    Energy Technology Data Exchange (ETDEWEB)

    Kemmler-Sack, S [Tuebingen Univ. (Germany, F.R.). Lehrstuhl fuer Anorganische Chemie 2

    1980-12-01

    In the systems BaO-M/sub 2/sup(V)O/sub 5/-WO/sub 3/ (Msup(V) = Nb, Ta) a new phase Ba/sub 5/BaWsub(3-x)Msub(x)sup(V)vacantOsub(15-x/2)vacantsub(x/2) with hexagonal 5 L structure (sequence hhccc; space group P-3m1) could be prepared. The range of existence is restricted to Msup(V) containing compounds. With Msup(V) = Nb the lower phase boundary is x = 3. In the Ta system it is reached between x = 2 and 3; the pure Ta pervoskite (Ba:Ta:O = 6:3:13 1/2 = 4:2:9) represents the final member of the series Ba/sub 3/Srsub(1-y)Basub(y)Ta/sub 2/O/sub 9/ with y = 1.

  10. Caracterización mecánica de aceros empleados en el sector de la construcción de Almería

    Directory of Open Access Journals (Sweden)

    Senoboua, A. J.

    2003-12-01

    Full Text Available Various tests have been conducted on the steel bars used in the construction of civil works in Almería (Spain during the period 18 January 2000-7 May 2001, with the aim of mechanically characterizing the different types of steel (weldable: B400S, B500S and ductile weldable: B400SD to determine whether there is a technical reason for the increase in the use of ductile weldable steel. For this, we have used a hydraulic machine to break by traction all the test samples that arrived to the laboratory, following the specifications of the UNE 7474-1:1992 and the UNE 7474-2:1992. The results indicate that only in 86 % of the cases does the steel B400SD satisfy the limits specified by the UNE 36065:1999-EX, as opposed to 95 and 94 % of the B400S and B500S steels. In addition, the ductile weldable steel registered mean values lower than those of B400S. This finding disagrees with expectations set by the specifications.

    Se realizaron varios ensayos sobre las barras de acero utilizadas en la construcción de obra civil en Almería, durante el período comprendido entre 18/1/2000 y 7/05/2001, con el fin de caracterizar, mecánicamente, los diferentes tipos de aceros (soldables: B400S, B500S y soldable dúctil: B400SD y, de esta forma, determinar si existe alguna razón técnica para un incremento del consumo del acero soldable dúctil. Para ello, se ensayaron a tracción todas las muestras que llegaron al laboratorio, siguiendo las normas UNE 7474-1:1992 y UNE 7474-2:1992. Los resultados indican que el acero B400SD cumple, sólo, en un 86 % los límites especificados en la norma UNE 36065:1999 -EX, frente al 95 y 94 % de los aceros B400S y B500S. Además, el acero soldable dúctil muestra unos valores medios inferiores al B400S. Este hecho discrepa de lo que se podría esperar según la norma que lo regula.

  11. Microstructure of a safe-end dissimilar metal weld joint (SA508-52-316L) prepared by narrow-gap GTAW

    Energy Technology Data Exchange (ETDEWEB)

    Ming, Hongliang [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); University of Chinese Academy of Sciences, 19 Yuquan Road, Beijing 100049 (China); Zhang, Zhiming [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, Jianqiu, E-mail: wangjianqiu@imr.ac.cn [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Han, En-Hou [Key Laboratory of Nuclear Materials and Safety Assessment, Liaoning Key Laboratory for Safety and Assessment Technique of Nuclear Materials, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Wang, Peipei; Sun, Zhiyuan [Shanghai Research Center for Weld and Detection Engineering Technique of Nuclear Equipment, Shanghai 201306 (China)

    2017-01-15

    The microstructure, residual strain and interfacial chemical composition distribution of a safe-end dissimilar metal weld joint (DMWJ, SA508-52-316L) prepared by narrow-gap gas-tungsten arc welding (NG-GTAW) were studied by optical microscope (OM) and scanning electron microscope equipped with an energy dispersive X-ray microanalysis (SEM/EDX) and an electron back scattering diffraction (EBSD) system. Complex microstructure and chemical composition distribution are found, especially at the SA508-52 interface and the 52-316L interface. In brief, a complicated microstructure transition exists within the SA508 heat affected zone (HAZ); the residual strain, the fraction of high angle random grain boundaries and low angle boundaries decrease with increasing the distance from the fusion boundary in 316L HAZ; neither typical type II boundary nor obvious carbon-depleted zone is found near the SA508-52 interface; dramatic and complicated changes of the contents of the main elements, Fe, Cr and Ni, are observed at the distinct interfaces, especially at the SA508-52 interface. No carbon concentration is found at the SA508-52 interface. - Highlights: •Residual strain and GBCD change as a function of the distance from FB in 316L HAZ. •Neither type II boundary nor obvious carbon-depleted zone is found in SA508 HAZ. •No carbon concentration is found at the SA508-52 interface. •The middle part of the DMWJ has the highest residual strain.

  12. A Mathematical Model of Intra-Colony Spread of American Foulbrood in European Honeybees (Apis mellifera L..

    Directory of Open Access Journals (Sweden)

    Eduardo O Jatulan

    Full Text Available American foulbrood (AFB is one of the severe infectious diseases of European honeybees (Apis mellifera L. and other Apis species. This disease is caused by a gram-positive, spore-forming bacterium Paenibacillus larvae. In this paper, a compartmental (SI framework model is constructed to represent the spread of AFB within a colony. The model is analyzed to determine the long-term fate of the colony once exposed to AFB spores. It was found out that without effective and efficient treatment, AFB infection eventually leads to colony collapse. Furthermore, infection thresholds were predicted based on the stability of the equilibrium states. The number of infected cell combs is one of the factors that drive disease spread. Our results can be used to forecast the transmission timeline of AFB infection and to evaluate the control strategies for minimizing a possible epidemic.

  13. PROTECCIÓN CONTRA LA CORROSIÓN EN SALES FUNDIDAS DE UN ACERO HOT ROLLED, EN EL RANGO DE TEMPERATURAS DE 400 ºC-600 ºC, RECUBIERTO POR ROCIADO TÉRMICO CON ACERO INOXIDABLE 312

    Directory of Open Access Journals (Sweden)

    JOSE LUDDEY MARULANDA

    2009-01-01

    Full Text Available Se evaluó la corrosión por sales fundidas mediante la técnica gravimétrica en un acero de bajo carbono tipo hot rolled, rociado térmicamente con una aleación de acero inoxidable tipo 312, con el equipo Rototec, en una mezcla de sal 20% Na2SO4 - 80% V2O5, entre 400ºC - 600ºC, durante tiempos de 1-7-22 horas. Los resultados mostraron una moderada protección de la capa rociada térmicamente y se presentó alta degradación en el recubrimiento a 600ºC. Se concluyó que la velocidad de corrosión aumenta con la temperatura y disminuye con el tiempo de exposición.

  14. The Cementation of Boron to Steels by the Method of Electrolytic Deposition; Cementation Electrolytique d'Aciers par le Bore; Tsementirovanie bora v stali putem ehlektroliticheskogo osazhdeniya; Cementacion de Aceros con Boro por Deposito Electrolitico

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, M. [Tokyo Institute of Technology (Japan)

    1964-06-15

    This report describes a fabricating method for cementation of a control rod with boron. The cementing is carried out by electrolysis of fused borax at about 900 Degree-Sign C, the steel rod to be cemented acting as a cathode, and the graphite electrode as an anode. As the electrolysis progresses, boron is deposited on/the steel rod and diffused into it. When suitable conditions of electrolysis exist, a case of the steel rod with as much as 20% boron content can easily be obtained. The kinds of steel investigated were carbon steel, stainless steels, high chrome steel etc., and each of them showed good results. (author) [French] L'auteur expose une methode de fabrication d'une barre de commande en acier cemente par le bore. La cementation est effectuee par l'electrolyse de borax fondu a environ 900 Degree-Sign C, la barre d'acier a cementer formant cathode et une electrode en graphite constituant l'anode. Au cours du processus d 'electrolyse, le bore se depose sur la barre d'acier et est diffuse dans le metal. Lorsque l'electrolyse s'effectue dans les conditions requises, on peut obtenir facilement une barre d'acier dont la teneur en bore atteint jusqu'a 20%. Les recherches ont porte sur des aciers tels que les aciers au carbone ordinaires, les aciers inoxydables, les aciers refractaires au chrome, etc. et on a obtenu de bons resultats pour chacun de ces aciers. (author) [Spanish] La memoria describe un metodo de obtencion de barras de control cementadas con boro. La cementacion se efectua por electrolisis de borax fundido a unos 900 Degree-Sign C. Como catodo se emplea la barra de acero que se desea cementar y como anodo, un electrodo de grafito. Conforme progresa la electrolisis, el boro se deposita sobre la barra de acero y penetra en la misma por difusion. Si las condiciones en que se efectua la electrolisis son adecuadas, se logra facilmente la cementacion de la barra de acero, que alcanza un contenido de hasta 20% de boro. Entre los aceros investigados, figuran

  15. Mejora de la tenacidad de un acero de ultraalto contenido en carbono nnediante unión por laminación con un acero al cromo y molibdeno

    Directory of Open Access Journals (Sweden)

    Pozuelo, M.

    2005-12-01

    Full Text Available Laminated composite materials containing five layers of ultrahigh carbon steel, 1.35%C, and five layers of a Cr-Mo steel were processed by roll bonding. The rolling procedure improves the bonding of layers and refines the microstructure, diminishing grain size and removing the pearlitic zones. Charpy impact tests were carried out to evaluate the impact properties. Toughness of the laminated composite was highly improved respect to the ultrahigh carbon steel. Moreover, it was double than that of the Cr-Mo steel in the arrester orientation. These results reveal the important role of the interfaces in the mechanical properties of the composite materials.

    Se procesaron mediante unión por laminación, dos materiales compuestos laminados de 10 capas: cinco capas de un acero de ultraalto contenido en carbono con 1,35 % C, alternadas con otras cinco de un acero al cromo y molibdeno. La laminación en caliente consolida la unión entre las capas y afina la microestructura, reduciendo el tamaño de grano y eliminando las zonas de perlita presentes inicialmente. Se realizaron ensayos de impacto Charpy para evaluar su resistencia al impacto. El material compuesto laminado mejoró sustancialmente la tenacidad del acero de ultraalto carbono, además de duplicar la resiliencia del acero al cromo y molibdeno en la orientación "en serie". Estos resultados ponen de manifiesto la importancia de las intercaras en las propiedades mecánicas de los materiales compuestos.

  16. Eksplorasi Potensi Ekowisata di Kawasan Api Tak Kunjung Pada Kabupaten Pamekasan

    Directory of Open Access Journals (Sweden)

    Dewi Kartika Sari Susena

    2015-04-01

    Full Text Available Penelitian ini bertujuan untuk mengetahui aspek potensi ekowisata di kawasan Api Tak Kunjung Padam kabupaten Pamekasan dan persepsi masyarakat sekitar tentang potensi ekowisata yang ada. Metode pengambilan data meliputi mendapatkan informasi umum dari Key person dengan menggunakan teknik purposive sampling, penelusuran pustaka, observasi lapang, pengumpulan data lokasi berdasarkan persepsi masyarakat dengan pemilihan responden dengan menggunakan teknik purposive sampling dan wawancara semi terstruktur. Sumber daya alam yang ada di sekitar kawasan objek wisata yang berpotensi untuk mendukung ekowisata yaitu, objek wisata Api Tak Kunjung Padam, umbi bentul (Colocasia esculenta L., lahan pertanian Singkong (Manihot esculenta Crantz, Kacang hijau (Phaseolus radiatus L., Pisang (Musa paradisiaca L. dan Jagung (Zea mays L., rengginang lorjuk, jubada, kaldu kokot, rujak dan campur madura. Berdasarkan hasil wawancara diketahui bahwa hasil panen dari lahan pertanian dimanfaatkan masyarakat setempat untuk menambah perekonomian dengan cara dijual di kawasan Api Tak Kunjung Padam maupun di pasar. Masyarakat setempat juga belum banyak mengetahui potensi sumber daya tersebut untuk dimanfaatkan sebagai pendukung konservasi lingkungan secara umum di wilayah tersebut. Kata Kunci : Api Tak Kunjung Padam, ekowisata, Persepsi.

  17. Morphologic analysis and phenotypic variations observed in the acid glands of Apis mellifera L. (1758 africanized worker bees (HYM.: Apidae in the region of Dourados, Mato Grosso do Sul, Brazil

    Directory of Open Access Journals (Sweden)

    Mônica Maria Bueno de Moraes

    2005-11-01

    Full Text Available In Apis mellifera,the acid gland can present atypical branching. It is composed of secretor cells that surround a canal leading into a non-muscular reservoir. We proposed to evaluate the morphology of the gland in worker bees of genetically distinct colonies, in terms of the presence and size of branching, the length of the main duct of the reservoir up to the branching point, and the total length of the gland. It was observed that the presence of branching varied from 30% to 76% with X = 59% ± 11.5%, and its length varied from 0.13mm ± 0.24mm to 1.03mm ± 1.54mm with X = 0.53mm ± 0.27mm; the variation in size of the main duct was from 5.97mm ± 1.61mm to 20.95mm ± 6.66mm with X = 12.3mm ± 5.7mm; the distance from the reservoir to the branching point was from 5.52mm ± 1.84mm to 19.53mm ± 6.42mm with X = 11.42mm ± 5.31mm, and the total length of the gland varied from 6.22mm ± 1.60mm and 21.98mm ± 7.40mm with X = 12.86mm ± 5.88mm. A large phenotypic variation was evident. The samples presented branching in at least 30% of the individuals, this characteristic being considered primitive. However, glands without branching suggest an evolution in that direction for this type of bee in the region. Concerning the genetic characteristics of the gland, in 31% of the colonies the workers presented small poison glands, genotype recessive homozygotes gm1gm1 and gm2gm2; in 69%, the workers presented large glands in heterozygote Gm2gm1 and dominant homozygotes Gm1Gm1 and Gm2Gm2. These results indicate a concentration of bees with large acid glands in the region, favoring a selection process for the production of poison.

  18. L{sub {iota}}, L{sub {alpha}}, L{sub {beta}} and L{sub {gamma}} X-ray fluorescence cross-sections of heavy elements for the exciting photons energy 38.18, 43.95, 50.21 and 59.5 keV

    Energy Technology Data Exchange (ETDEWEB)

    Bastug, Arif [Department of Physics Education, College of Education, Erzincan University, 24030 Erzincan (Turkey)], E-mail: abastug40@hotmail.com

    2008-03-15

    The cross-sections for the production of L{sub {iota}}, L{sub {alpha}}, L{sub {beta}} and L{sub {gamma}} X-ray fluorescence (XRF) in Er, Ta, W, Au, Hg, Tl, Pb and Bi by photons with energies in the range 38-59.5 keV have been measured, using a standard doublereflection experimental set-up. Measurements have been performed using an annular 241 Am primary source and X-ray emitting secondary-exciter system. Experimental cross-sections have been compared with the theoretically calculated values of L X-ray cross-sections and fairly good agreement is observed between the experimental and theoretical values.

  19. Facile LC-UV methods for simultaneous monitoring of ciprofloxacin and rosuvastatin in API, formulations and human serum.

    Science.gov (United States)

    Arayne, M Saeed; Sultana, Najma; Tabassum, Arman

    2015-02-01

    An efficient, selective and cost-effective liquid chromatographic assay was developed and validated for the simultaneous quantification of ciprofloxacin and rosuvastatin in Active Pharmaceutical Ingredients (API), pharmaceutical formulations and in human serum. The chromatographic system consisted of mobile phase methanol-water, 90:10 v/v at pH 3.0 adjusted with o-phosphoric acid, pumped at 1.0 mL/min through a prepacked Purospher Star C18 (5 µm, 25 × 0.46 cm) column and effluent was monitored at the isosbestic point (255 nm) as well as at the λmax of individual drugs (243 and 271 nm). The method was validated over a linear concentration range of 0.25-15 µg/mL for ciprofloxacin and 0.33-20 µg/mL for rosuvastatin (r(2)  ≥ 0.999). The ranges of reliable response (limits of detection and quantitation) for ciprofloxacin were 3-15 and 9-45 ng/mL and 17-29 and 52-88 ng/mL, respectively, for rosuvastatin in all API, pharmaceutical formulations and human serum. Analytical recovery from human serum was >98% and relative standard deviation (RSD) was <2. The accuracies were 97.13-102.55 and 97.41-101.31% and precisions in RSD were 0.04-1.90 and 0.02-1.23% for ciprofloxacin and rosuvastatin, respectively. No matrix interferences, ion suppression/enhancement and carry-over were detected. The total assay run time was less than 5 min. In another study, for optimum performance the detector was programmed for multiwavelength scanning at the absorption maxima of each component. Consequently, the linearity range was improved and limit of detection and quantitation values were down to 1-4 and 4-12 ng/mL for ciprofloxacin and 3-5 and 9-15 ng/mL for rosuvastatin, respectively. The validation parameters fitted ICH guidelines through the isosbestic and individual λmax approach. The small sample volume and simplicity of preparation make this method suitable for use in human serum samples, pharmaceutical formulations, quality control, drug

  20. Efecto del procedimiento de soldadura sobre las propiedades de uniones soldadas de aceros microaleados para cañería Welding procedure effect on the properties of microalloyed steel welded joints for metal fabrication

    Directory of Open Access Journals (Sweden)

    Mónica Zalazar

    2009-03-01

    Full Text Available El objetivo del trabajo fue, en esta primera etapa, comparar las propiedades mecánicas y la microestructura del acero HIC, aleado al Nb-Ti-Cu-Ni, resistente a la corrosión, con las del acero normal NOR, microaleado con Nb-V-Ti, ambos caracterizados mediante análisis químico, mediciones de dureza, estudios metalográficos y ensayos de tracción e impacto. Con el fin de establecer la temperatura de precalentamiento óptima se realizaron ensayos de soldabilidad Tekken a distintas temperaturas y de acuerdo con la Norma JIS Z 3158. Luego se llevaron a cabo soldaduras circunferenciales de cañerías fabricadas con ambos aceros diseñándose procedimientos para la utilización, por un lado, de electrodos revestidos (SMAW: shielded metal arc welding, electrodos de distintos proveedores para todas las pasadas y por el otro, la primera pasada usando soldadura automática con alambre macizo bajo CO2 (GMAW: gas metal arc welding y el resto de las mismas con alambre tubular autoprotegido (FCAW-S: flux cored arc welding-selfshielded. Las soldaduras fueron calificadas de acuerdo con el Código API 1104. Los resultados de los análisis metalográficos y los ensayos mecánicos de tracción, dureza e impacto de las juntas soldadas revelaron la influencia de los consumibles de soldadura y del metal base en las propiedades de las uniones. Se observaron diferencias en las propiedades de las uniones soldadas con consumibles de igual especificación y distintos proveedores. De las diferentes combinaciones ensayadas se definieron valores óptimos para la soldadura de estos aceros.The objective of this work was, in this first step, to compare mechanical property and microstructure of the steel HIC, alloyed with Nb-Ti-Cu-Ni, corrosion resistant, to those of a normal steel NOR, microlloyed with Nb-V-Ti, characterized through chemical analysis, hardness measurements, metallographic studies and tensile and Charpy-V properties. The preheating temperature was established

  1. In vivo evaluation of the 3-carboranyl thymidine analogue (3-CTA), N5-2OH, for neutron capture therapy

    International Nuclear Information System (INIS)

    Barth, Rolf F.; Yang, Weilian; Wu, Gong; Byun, Youngjoo; Tjarks, Werner; Eriksson, Staffan; Binns, Peter J.; Riley, Kent J.

    2006-01-01

    The purpose of the present study was to evaluate a 3 CTA, designated N5-2OH, as a boron delivery agent for NCT. Target validation was established using the thymidine kinase 1 (+) wild type L929 cell line and its TK1(-) counterpart, which were implanted subcutaneously into NIH nu/nu mice. 10 B-enriched N5-2OH, solubilized in DMSO (50μg 10 B in 15μl), was administered by 2 intratumoral (i.t.) injections at 2 h intervals. Two hours later the animals were irradiated at the MITR-II Research Reactor, following which tumor volumes were determined over a period of 30 days. Mice bearing TK1(+) wild type tumors, which had received N5-2OH, had a 15 fold inhibition in tumor growth compared to TK1(-) controls (247 versus 3,603 mm 3 ). Based on these data, biodistribution and therapy studies were initiated in F98 glioma bearing rats. Animals received 500μg of N5-2OH, administered intracerebrally (i.c.) by convection enhanced delivery (CED) using ALZET pumps (8μl/h for 24 h). The tumor boron concentration was 17.3μg/g compared to undetectable amounts in normal brain and blood. BNCT was carried out 14 d following i.c. implantation of 10 3 F98 glioma cells and 24 h following CED of N5-2OH (500μg/200μl). The mean survival time (MST) of these animals was 38 d compared to 31 d and 25 d, respectively, for irradiated and untreated controls. Studies are planned to optimize the delivery and formulation of N5-2OH and additional therapy studies will be carried out using N5-2OH in combination with BPA and BSH. (author)

  2. Hormigones de alta resistencia con nano-adiciones y fibras de acero

    OpenAIRE

    Alizo Mirabal, Manuel Arturo

    2015-01-01

    El presente Trabajo Fin de Máster consistió en determinar la influencia que pueden poseer las nano-adiciones de Sílice y Alúmina y fibras de acero en un Hormigón de Alta Resistencia. Partiendo de una dosificación de Hormigón de Alta Resistencia conocida, que contenía humo de Sílice (10%) y fibras de poliolefina (3kg/m3), se les procedió a sustituir por la incorporación de nano-adiciones de Sílice y Alúmina (7% y 3% respectivamente) y añadiendo fibras de acero en lugar de poliolefina. En el pr...

  3. Floral biology and behavior of Africanized honeybees Apis mellifera in soybean (Glycine max L. Merril

    Directory of Open Access Journals (Sweden)

    Wainer César Chiari

    2005-05-01

    Full Text Available This research was carried out to evaluate the pollination by Africanized honeybees Apis mellifera, the floral biology and to observe the hoarding behavior in the soybean flowers (Glycine max Merril, var. BRS-133. The treatments were constituted of demarcated areas for free visitation of insects, covered areas by cages with a honeybee colony (A. mellifera and also covered areas by cage without insects visitation. All areas had 24 m² (4m x 6m. The soybean flowers stayed open for a larger time (82.82 ± 3.48 hours in covered area without honeybees. The stigma of the flowers was also more receptive (P=0.0021 in covered area without honeybees (87.3 ± 33.0% and at 10:42 o'clock was the schedule of greater receptivity. The pollen stayed viable in all treatments, the average was 99.60 ± 0.02%, which did not present differences among treatments. The percentage of abortion of the flowers was 82.91% in covered area without honeybees, this result was superior (P=0.0002 to the 52.66% and 53.95% of the treatments uncovered and covered with honeybees, respectively. Honeybees were responsible for 87.7% of the pollination accomplished by the insects. The medium amounts of total sugar and glucose measured in the nectar of the flowers were, 14.33 ± 0.96 mg/flower and 3.61 ± 0.36 mg/ flower, respectively, not showing differences (PEste experimento teve como objetivos avaliar a polinização realizada por abelhas Apis mellifera, estudar a biologia floral e observar o comportamento de coleta nas flores de soja (Glycine max L. Merril, variedade BRS-133 plantadas na região de Maringá-PR. Os tratamentos constituíram de áreas demarcadas de livre visitação por insetos, áreas cobertas por gaiolas, com uma colônia de abelhas (A. mellifera no seu interior e plantas também cobertas por gaiola que impedia a visitação por insetos. Todas as áreas possuíam 24 m² (4 m x 6 m. As flores de soja permaneceram abertas por um tempo maior (82,82 ± 3,48 horas no

  4. (5/2-→5/2+) 803 keV beta transition in 147Nd

    International Nuclear Information System (INIS)

    Lakshminarayana, S.; Srinivasa Rao, M.; Seshagiri Rao, V.; Sastry, D.L.

    1978-01-01

    The existing experimental results on the 5/2 - →5/2 + 803 keV beta transition in 147 Nd are mutually contradictory to classify it under xi-approximation. To resolve this contradiction, the β-γ directional correlations are performed carefully as a function of energy using a conventional fast-slow coincidence scintillation system. The attenuation factor G 2 in this case turns out to be 0.64 +- 0.05. The results on the longitudinal electron polarization and the shape measurements are combined with the present results and an attempt is made to extract the nuclear matrix elements governing this first forbidden non-unique beta transition following Simm's formalism. Results are discussed based on the final sets of matrix elements. (auth.)

  5. BEE VENOM TRAP DESIGN FOR PRODUCE BEE VENOM OF APIS MELLIFERA L. HONEY BEES

    OpenAIRE

    Budiaman

    2015-01-01

    Bee venom is one honey bee products are very expensive and are required in the pharmaceutical industry and as an anti-cancer known as nanobee, but the production technique is still done in the traditional way. The purpose of this study was to design a bee venom trap to produce bee venom of Apis mellifera L honey bees. The method used is to design several models of bee venom apparatus equipped weak current (DC current) with 3 variations of voltage, ie 12 volts, 15 volts and 18 volts coupled...

  6. Moessbauer studies of the LiAl sub(5-x) Fe sub(x) O8 and LiGa sub(5-x) Fe sub(x) O8 systems

    International Nuclear Information System (INIS)

    Barthem, V.M.T.S.; Maria Neto, J.; Souza Barros, F. de

    1982-01-01

    Comparative Moessbauer studies of the LiGa sub(5-x) Fe sub(x) O 8 and LiAl sub(5-x) Fe sub(x) O 8 systems are shown. The characteristics of the Moessbauer spectra, obtained with LiGa 5 O 8 samples with 0,1% of Fe 3+ , differ drastically from that observed with LiAl 5 O 8 with the same three-valent iron concentration. All these differences are related to the more covalent character of the gallium-oxygen binding, when compared with the aluminium-oxygen one. (L.C.) [pt

  7. Análisis comparativo de la calidad del acero de refuerzo distribuido en Boyacá

    Directory of Open Access Journals (Sweden)

    Jimmy Vergara Silva, Óscar Javier Gutiérrez Junco

    2011-05-01

    Full Text Available Presenta  los  resultados  del  análisis  comparativo  de barras de acero de refuerzo, según las exigencias de la Norma Técnica Colombiana NTC 2289 [1], realizado a cinco marcas diferentes distribuidas para la industria de  la  construcción  en  Boyacá.  Inicialmente  se caracterizaron  las barras de  acero mediante  ensayos, para  determinar  su  composición  química  y  sus propiedades físicas y mecánicas; las características de la fractura del acero de refuerzo se observaron con el microscopio  electrónico  de  barrido  (MEB. Adicionalmente,  se  analizaron  muestras  conmicroscopio óptico, con  técnicas de espectrometría paraobservar y determinar las características del metal base de  las probetas. Los resultados  indican que la calidad del acero de refuerzo distribuido en Boyacá cumple en un alto  porcentaje con las exigencias sismo-resistentes para construcción; sin embargo, es importante que los constructores realicen control de calidad.

  8. Assessment of the Potential of Honeybees (Apis mellifera L.) in Biomonitoring of Air Pollution by Cadmium, Lead and Vanadium

    NARCIS (Netherlands)

    Steen, van der J.J.M.; Kraker, de J.; Grotenhuis, J.T.C.

    2015-01-01

    The aim of our study was to explore whether honeybees (Apis mellifera L.) could be used as a reliable alternative to the standard mechanical devices for monitoring of air quality, in particular with respect to the concentration of the heavy metals cadmium (Cd), lead (Pb) and vanadium (V). We

  9. Ductilidad en caliente y mecanismos de fractura de un acero de construcción

    Directory of Open Access Journals (Sweden)

    Calvo, J.

    2006-02-01

    Full Text Available The hot ductility of a structural steel produced from scrap recycling has been studied to determine the origin of the transverse cracks in the corners that appeared in some billets. Samples extracted both from a billet with transverse cracks and from a billet with no external damage were tested. To evaluate the influence of residual elements and inclusions, the steel was compared to another one impurity free. Reduction in area of the samples tensile tested to the fracture was taken as a measure of the hot ductility The tests were carried out at temperatures ranging from 1000ºC to 650ºC and at a strain rate of 1·10- 3 s-1. The fracture surfaces of the tested samples were observed by scanning electron microscopy in order to determine the embrittling mechanisms that could be acting. The steel with residuals and impurities exhibited lower ductility values for a wider temperature range than the clean steel. The embrittling mechanisms also changed as compared to the impurity free steel.

    Se evaluó la ductilidad en caliente de un acero de construcción procedente del reciclaje de chatarra con el fin de determinar el origen de las grietas transversales que aparecen en las esquinas de algunas palanquillas. Para ello, se extrajeron probetas de dos palanquillas de una misma calidad de acero. Una de las palanquillas había presentado agrietamiento transversal al ser colada y, la otra, no. Para conocer la influencia de los elementos residuales e inclusiones en la ductilidad en caliente, otro acero, con la misma composición pero sin impurezas, se fabricó en laboratorio y fue sometido al mismo análisis que los aceros comerciales. La ductilidad en caliente se midió como la reducción del área de las probetas ensayadas a tracción hasta la rotura. Las condiciones a las que se realizaron los ensayos fueron temperaturas de 1.000 a 650 ºC y a una velocidad de deformación de 1·10-3 s-1. Las superficies de fractura de las probetas ensayadas se

  10. Evaluación electroquímica de soldaduras en tubos capilares de acero inoxidable

    Directory of Open Access Journals (Sweden)

    Javier E. Rodríguez-Yáñez

    2014-02-01

    Full Text Available La recuperación de capilares de acero 316L utilizados en pozos geotérmicos neutros, por medio de soldadura orbital autógena, se evalúa desde el punto de vista de su resistencia a la corrosión en las condiciones de utilización, mediante técnicas electroquímicas básicas. En el pretratamiento se encuentra que es más conveniente realizar un decapado químico previo a la soldadura por 5 minutos. Mientras que posteriormente a la soldadura, la aplicación de tratamiento térmico de reducción de tensiones no se justifica desde el punto de vista de la resistencia a la corrosión. También se plantea la comparación de los capilares soldados respecto a capilares nuevos y usados, teniendo los capilares soldados un comportamiento intermedio entre ambos.

  11. 42 CFR 52h.5 - Conflict of interest.

    Science.gov (United States)

    2010-10-01

    ... 42 Public Health 1 2010-10-01 2010-10-01 false Conflict of interest. 52h.5 Section 52h.5 Public... RESEARCH GRANT APPLICATIONS AND RESEARCH AND DEVELOPMENT CONTRACT PROJECTS § 52h.5 Conflict of interest. (a) This section applies only to conflicts of interest involving members of peer review groups. This...

  12. Programmatic access to logical models in the Cell Collective modeling environment via a REST API.

    Science.gov (United States)

    Kowal, Bryan M; Schreier, Travis R; Dauer, Joseph T; Helikar, Tomáš

    2016-01-01

    Cell Collective (www.cellcollective.org) is a web-based interactive environment for constructing, simulating and analyzing logical models of biological systems. Herein, we present a Web service to access models, annotations, and simulation data in the Cell Collective platform through the Representational State Transfer (REST) Application Programming Interface (API). The REST API provides a convenient method for obtaining Cell Collective data through almost any programming language. To ensure easy processing of the retrieved data, the request output from the API is available in a standard JSON format. The Cell Collective REST API is freely available at http://thecellcollective.org/tccapi. All public models in Cell Collective are available through the REST API. For users interested in creating and accessing their own models through the REST API first need to create an account in Cell Collective (http://thecellcollective.org). thelikar2@unl.edu. Technical user documentation: https://goo.gl/U52GWo. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  13. Fischer matrices of Dempwolff group $2^{5}{^{cdot}}GL(5,2$

    Directory of Open Access Journals (Sweden)

    Ayoub Basheer Mohammed Basheer

    2012-12-01

    Full Text Available In cite{Demp2} Dempwolff proved the existence of a group of theform $2^{5}{^{cdot}}GL(5,2$ (a non split extension of theelementary abelian group $2^{5}$ by the general linear group$GL(5,2$. This group is the second largest maximal subgroup of thesporadic Thompson simple group $mathrm{Th}.$ In this paper wecalculate the Fischer matrices of Dempwolff group $overline{G} =2^{5}{^{cdot}}GL(5,2.$ The theory of projective characters isinvolved and we have computed the Schur multiplier together with aprojective character table of an inertia factor group. The fullcharacter table of $overline{G}$ is then can be calculated easily.

  14. L X-ray intensity ratio measurements using selective L sub-shell photo-ionisation on synchrotron

    Science.gov (United States)

    Bansal, Himani; Tiwari, M. K.; Mittal, Raj

    2017-10-01

    Lα/Lℓ, Lβ /Lℓ and Lγ/Lℓ intensity ratios have been measured for elements in the range 66≤Z≤83 at tuned photon energies on synchrotron beam line-16 at Indus-2, India. For each element, three incident energies Ei were E3; EL3 EL1 where ELi are Li absorption edge energies of the element. Emitted L X-ray spectrum of an element constitutes a number of X-ray lines generally grouped into four main groups due to limited resolution of available detectors as Lℓ(L3-M1), Lα(L3-M4,5), Lβ(L1-M2,3,4,5,N4; L2-M3,4; L3-N1,4,5,O1,4,5) and Lγ(L2-N1,4,O1,4; L1-N2,3,5,O3,2). Lα and Lℓ both comprise only the lines feeding L3 level and Lβ group comprises X-ray lines feeding all the three sub-shells where as Lγ involves contribution from L1 and L2 feedings. Only E3 excitation gives the ratios free from intra sub-shell Coster-Kronig (CK) transitions while excitations E2 and E1 give CK affected Lβ/Lℓ and Lγ/Lℓ X-ray intensity ratios and Lα/Lℓ still remains free from CKs. The pattern of intensity ratios at three excitation energies of elements was well interpreted in terms of on/off of CK transitions (Bambynek et al., 1972; Campbell, 2003) and outer shell electron filling configuration (Scofield, 1973).

  15. DEFORMACIÓN ELÁSTICA RESIDUAL EN LÁMINAS DE ACERO AISI 304 RECUBIERTAS CON UNA PELÍCULA DE NITRURO DE TITANIO DEPOSITADA POR PVD-MAGNETRON SPUTTERING

    Directory of Open Access Journals (Sweden)

    H. A. COLORADO

    2009-01-01

    Full Text Available Se realizó una caracterización mediante difracción de rayos x (DRX en láminas de acero inoxidable AISI 304 recubierto con una capa de nitruro de titanio de 3 um de espesor, obtenida mediante deposición física de vapor (PVD-MAGNETRON SPUTTERING a una temperatura de 200 °C. se tomaron imágenes de microscopía electrónica de barrido (MEB, microscopía óptica (MO y microscopía de fuerza atómica (MFA para caracterizar el sustrato, la capa y la zona cercana a la intercara. adicionalmente se determinó la deformación elástica residual asociada con el ensanchamiento de los picos de DRX.

  16. Evaluación de diferentes aceros para la evolución de hidrógeno en KOH

    Directory of Open Access Journals (Sweden)

    Falk Michel Julke

    2014-05-01

    Full Text Available Se estudió el comportamiento electroquímico de los diferentes tipos de aceros comerciales de bajo costo (A36, 430 y 304 como electrodos para la obtención de hidrógeno. El propósito de este trabajo fue estudiar la evolución de hidrógeno, para lo cual se utilizaron técnicas electroquímicas como cronoamperometría y curvas voltamperométricas, en diferentes concentraciones de KOH (5% y 25% m/m. El acero inoxidable 304 en una concentración de 25%m/m tuvo el mejor desempeño, pues en estas condiciones el inicio de liberación de hidrógeno disminuyó y presentó el menor requerimiento de potencial para su uso como placa bipolar.

  17. Influencia de la microestructura en el comportamiento a fatiga de aceros inoxidables austeníticos con alto contenido en molibdeno

    Directory of Open Access Journals (Sweden)

    Oñoro, J.

    2006-02-01

    Full Text Available Austenitic stainless steels with molybdenum present high mechanical properties and corrosion resistance to aggressive environments. These steels have been used to tank and vessel components for high corrosive liquids as phosphoric, nitric and sulphuric acids. These materials with low carbon and nitrogen addition have been proposed candidates as structural materials for the international thermonuclear experimental reactor (ITER in-vessel components. Molybdenum addition in austenitic stainless steel improves mechanical and corrosion properties, but with it can produce the presence of nitrogen microstructure modifications by presence or precipitation of second phases. This paper summarises the fatigue and corrosion fatigue behaviour of two 317LN stainless steels with different microstructure. Fully austenitic steel microstructure show better fatigue, corrosion fatigue resistance and better ductility than austenitic steel with delta ferrite microstructure, mainly at low stresses.

    Los aceros inoxidables austeníticos con elevados contenidos en molibdeno presentan alta resistencia mecánica y resistencia a los medios corrosivos. Se utilizan en la construcción de depósitos y recipientes para el almacenamiento y transporte de líquidos altamente corrosivos, tales como ácido fosfórico, nítrico o sulfúrico. Estos materiales con bajo carbono y adiciones de nitrógeno han sido propuestos como candidatos para materiales estructurales en la fabricación de la vasija del reactor experimental termonuclear internacional (ITER. La adición de molibdeno mejora las propiedades frente a la corrosión de los aceros inoxidables austeníticos. Sin embargo, este aumento del contenido en molibdeno, junto con la presencia de nitrógeno, puede producir modificaciones microestructurales, por la aparición de fases precipitadas o segundas fases. En este trabajo, se analiza el comportamiento la fatiga y corrosión-fatiga de dos aceros inoxidables austen

  18. Comparative Analyses of Cu-Zn Superoxide Dismutase (SOD1) and Thioredoxin Reductase (TrxR) at the mRNA Level between Apis mellifera L. and Apis cerana F. (Hymenoptera: Apidae) Under Stress Conditions.

    Science.gov (United States)

    Koo, Hyun-Na; Lee, Soon-Gyu; Yun, Seung-Hwan; Kim, Hyun Kyung; Choi, Yong Soo; Kim, Gil-Hah

    2016-01-01

    This study compared stress-induced expression of Cu-Zn superoxide dismutase (SOD1) and thioredoxin reductase (TrxR) genes in the European honeybee Apis mellifera L. and Asian honeybee Apis cerana F. Expression of both SOD1 and TrxR rapidly increased up to 5 h after exposure to cold (4 °C) or heat (37 °C) treatment and then gradually decreased, with a stronger effect induced by cold stress in A. mellifera compared with A. cerana. Injection of stress-inducing substances (methyl viologen, [MV] and H2O2) also increased SOD1 and TrxR expression in both A. mellifera and A. cerana, and this effect was more pronounced with MV than H2O2. Additionally, we heterologously expressed the A. mellifera and A. cerana SOD1 and TrxR proteins in an Escherichia coli expression system, and detection by SDS-PAGE, confirmed by Western blotting using anti-His tag antibodies, revealed bands at 16 and 60 kDa, respectively. Our results show that the expression patterns of SOD1 and TrxR differ between A. mellifera and A. cerana under conditions of low or high temperature as well as oxidative stress. © The Author 2016. Published by Oxford University Press on behalf of the Entomological Society of America.

  19. Stainless-Steel-Gadolinium Alloys; Alliages Acier Inoxydable-Gadolinium; Splavy iz nerzhaveyushchej stali i gadoliniya; Aleaciones de Acero Inoxidable-Gadolinio

    Energy Technology Data Exchange (ETDEWEB)

    Copeland, M.; Kato, H. [Albany Metallurgy Research Center, Bureau Of Mines, United States Department of the Interior, Albany, OR (United States)

    1964-06-15

    mineures ont une grande influence sur les structures resultant de traitements equilibrants et sur les possibilites de transformation des aciers. Lorsque le gadolinium est melange a de l 'acier au chrome et au nickel, deux phases mineures, Fe{sub 9}Gd et Ni{sub 7}Gd, fondent a 1080 Degree-Sign C, ce qui impose une limite superieure aux temperatures de traitement a chaud et de transformation. Les auteurs ont pu facilement transformer des alliages comprenant jusqu'a 5 Degree-Sign Io en poids de gadolinium et determiner leurs caracteristiques mecaniques et leur resistance a la corrosion. Ils n'ont observe aucun changement dans les caracteristiques mecaniques de l'acier ou sa resistance a la corrosion par l'eau chaude, lorsqu'ils lui ont ajoute'jusqu'a 3% en poids de gadolinium. En raison des limites imposees aux temperatures de transformation des aciers au chrome et au nickel par le point de fusion des phases mineures, les auteurs ont etudie les effets du gadolinium sur des aciers au chrome. Ils ont releve une seule phase mineure qui fond a 1320 Degree-Sign C en etudiant l 'isoplethe du gadolinium a 10% en poids dans l 'alliage chrome-fer-gadolinium. Cette propriete permettrait d'equilibrer et de transformer ces aciers au gadolinium aux temperatures auxquelles on opere normalement. (author) [Spanish] En vista de la excelente resistencia a la corrosion de los aceros inoxidables y del interes que presenta el gadolinio como veneno nuclear, se han estudiado aleaciones de esos dos metales. El gadolinio fue aleado con aceros inoxidables de tipo AISI-304 y al cromo, y se estudiaron las relaciones de fase, la facilidad de trabajo y las propiedades de estas aleaciones. Se observo que en las aleaciones que contienen bajos porcentajes de gadolinio, los puntos de fusion de las fases menores ejercen un efecto muy marcado sobre las estructuras resultantes de los tratamientos de equilibracion y sobre la facilidad de trabajo de los afceros. Cuando se alea el gadolinio con acerce al cromo

  20. Structures of Adenovirus Incomplete Particles Clarify Capsid Architecture and Show Maturation Changes of Packaging Protein L1 52/55k.

    Science.gov (United States)

    Condezo, Gabriela N; Marabini, Roberto; Ayora, Silvia; Carazo, José M; Alba, Raúl; Chillón, Miguel; San Martín, Carmen

    2015-09-01

    Adenovirus is one of the most complex icosahedral, nonenveloped viruses. Even after its structure was solved at near-atomic resolution by both cryo-electron microscopy and X-ray crystallography, the location of minor coat proteins is still a subject of debate. The elaborated capsid architecture is the product of a correspondingly complex assembly process, about which many aspects remain unknown. Genome encapsidation involves the concerted action of five virus proteins, and proteolytic processing by the virus protease is needed to prime the virion for sequential uncoating. Protein L1 52/55k is required for packaging, and multiple cleavages by the maturation protease facilitate its release from the nascent virion. Light-density particles are routinely produced in adenovirus infections and are thought to represent assembly intermediates. Here, we present the molecular and structural characterization of two different types of human adenovirus light particles produced by a mutant with delayed packaging. We show that these particles lack core polypeptide V but do not lack the density corresponding to this protein in the X-ray structure, thereby adding support to the adenovirus cryo-electron microscopy model. The two types of light particles present different degrees of proteolytic processing. Their structures provide the first glimpse of the organization of L1 52/55k protein inside the capsid shell and of how this organization changes upon partial maturation. Immature, full-length L1 52/55k is poised beneath the vertices to engage the virus genome. Upon proteolytic processing, L1 52/55k disengages from the capsid shell, facilitating genome release during uncoating. Adenoviruses have been extensively characterized as experimental systems in molecular biology, as human pathogens, and as therapeutic vectors. However, a clear picture of many aspects of their basic biology is still lacking. Two of these aspects are the location of minor coat proteins in the capsid and the

  1. Effects of Apis mellifera adansonii, L. 1758 (Apidae: Hymenoptera ...

    African Journals Online (AJOL)

    pollination on yields of Cucumeropsis mannii (Naudin) in Kisangani, ... 1Unit of Functional and Evolutionary Entomology, University of Liège, ... number of fruits per plant, average weight of seeds extracted per fruit, ... enhance symbiotic interactions Apis mellifera with C. mannii in DRC. ..... Trends in Ecology and Evolution,.

  2. Influencia del tamaño del cristal de cinc de láminas de acero galvanizadas en ambientes que contienen cloruros y sulfatos

    Directory of Open Access Journals (Sweden)

    Julieth Andrea Ramírez-Jerez

    2015-05-01

    Full Text Available El trabajo evaluó la influencia del tamaño del cristal de cinc en el comportamiento electroquímico de láminas de acero galvanizadas por inmersión en caliente. Los ensayos se realizaron en una celda electroquímica plana en soluciones con diferentes concentraciones de NaCl y NaSO4. La velocidad y el mecanismo de corrosión, así como las características resistivas y difusivas de las láminas se evaluaron mediante técnicas electroquímicas, como espectroscopia de impedancia electroquímica (EIS, resistencia a la polarización (Rp y curvas potenciodinámicas. La composición y distribución de los productos de corrosión (FeO y algunos compuestos de cinc y el daño superficial causado por estos se determinaron por medio de DRX y SEM-EDS. Los resultados mostraron que la degradación de la capa de óxidos formada se ve afectada por la presencia de cloruros que penetran, llegan a la superficie del metal base y generan corrosión localizada.

  3. Fragilización por hidrógeno en tuberías de acero

    OpenAIRE

    Gutiérrez-Solana Salcedo, Federico

    2011-01-01

    Se pretende analizar el comportamiento en presencia de hidrogeno de las tuberías de acero de sistemas de transporte de combustibles gaseosos en uso para ello: 1.- Se estudia la sensibilidad a la fragilización por hidrogeno del acero de estas tuberías por dos métodos diferentes: polarización catódica y ambiente de hidrogeno gaseoso diseñando y construyendo una cámara para ensayos mecánicos en hidrogeno a presión primera de su genero en España. 2.- Se determina la tenacidad a fractura kic de es...

  4. CÁLCULO DE LA TENSIÓN DE FLUENCIA EN ACEROS DEFORMADOS EN CALIENTE

    OpenAIRE

    Béjar, L; Hernández, C. A

    2001-01-01

    Se ha desarrollado un modelo matemático para la predicción de la curva de fluencia de la austenita deformada en aceros de baja aleación. Las ecuaciones constitutivas tienen en cuenta los mecanismos gobernantes durante la deformación plástica -responsables de la forma de la curva- y emplea las variables de proceso y la composición química del acero. Para una demostración de su precisión, el modelo propuesto se ha comparado con las curvas de fluencia clásicas de Cook en condiciones hasta dos ór...

  5. Fatal intoxication with 3-methyl-N-methylcathinone (3-MMC) and 5-(2-aminopropyl)benzofuran (5-APB).

    Science.gov (United States)

    Adamowicz, Piotr; Zuba, Dariusz; Byrska, Bogumiła

    2014-12-01

    The emergence of a large number of new psychoactive substances (NPSs) in recent years poses a serious problem to clinical and forensic toxicologists. Here we report a patient who administrated ca. 500mg of 3-MMC (3-methyl-N-methylcathinone) and 400mg of 5-APB (5-(2-aminopropyl)benzofuran) in combination with 80g of ethyl alcohol. The clinical manifestations included agitation, seizures, hypertension, tachycardia, hyperthermia and bradycardia. The patient did not recover and died around 4h after the use of drugs. The cause of death was acute cardiovascular collapse that occurred following mixed intoxication with NPSs and alcohol. Toxicological analysis of post-mortem blood revealed 3-MMC and 5-APB in concentrations of 1.6μg/mL and 5.6μg/mL, respectively. Moreover, the serum alcohol concentration was 1.4g/L in ante-mortem sample collected 1h after admission to the hospital. This is the first report on blood concentration of 3-MMC and 5-APB in fatal intoxication. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  6. Drug Interaction API

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Interaction API is a web service for accessing drug-drug interactions. No license is needed to use the Interaction API. Currently, the API uses DrugBank for its...

  7. Espectro polínico de amostras de mel de Apis mellifera L., coletadas na Bahia Pollen spectrum of samples of Apis mellifera L., honey collected in Bahia State, Brazil

    Directory of Open Access Journals (Sweden)

    AUGUSTA CAROLINA DE CAMARGO CARMELLO MORETI

    2000-01-01

    Full Text Available O espectro polínico encontrado em amostras de mel provenientes de seis municípios do Estado da Bahia foi analisado com o objetivo de contribuir para o conhecimento da flora visitada por Apis mellifera L. 1758 (Hymenoptera: ApidaeA identificação dos tipos polínicos foi feita por meio de literatura especializada e de informações de campo. Foram encontrados 43 tipos de pólen, sendo consideradas como dominantes as espécies Eucalyptus sp. (Myrtaceae, Mimosa verrucosa Benth. (Mimosaceae, M. scabrella Benth. (Mimosaceae e Bauhinia sp. (Caesalpiniaceae. Os tipos acessórios foram Alternanthera ficoidea R.Br. (Amaranthaceae, tipo Compositae (Asteraceae e Cecropia sp. (Moraceae. Destacou-se a participação de Mimosa sp. (Mimosaceae e de outras espécies silvestres na composição dos méis nos municípios considerados, registrando-se ainda a espécie Eucalyptus sp. (Myrtaceae como uma das principais fontes de alimento das abelhas dessa região.Pollen spectrum found in honey samples from six localities of Bahia State, Brazil, was analyzed with the objective to contribute for the knowledge of the plants used by Apis mellifera L., 1758 (Hymenoptera: Apidae. The identification of the pollen types was made by specialized literature and by field information. Two hundred pollen grains were studied in order to determine the percentage and the occurrence of each type. Forty three pollen types were identified, being considered as the predominant types Eucalyptus sp. (Myrtaceae, Mimosa verrucosa Benth. (Mimosaceae, M. scabrella Benth. (Mimosaceae and Bauhinia sp. (Caesalpiniaceae. The accessory pollen types were Alternanthera ficoidea R.Br. (Amaranthaceae, Compositae type (Asteraceae and Cecropia sp. (Moraceae. It is intense the participation of Mimosa sp. (Mimosaceae and other wild species in the honey composition of the six localities considered. Eucalyptus sp. (Myrtaceae is one of the dominant sources of bee food in some regions of Bahia State.

  8. Study of sulphate-reducing bacteria corrosion in the weld joint for API X-70 steel

    Energy Technology Data Exchange (ETDEWEB)

    Flores, J. E.; Patino-Carachure, C.; Alfonso, I.; Rodriguez, J. A.; Rosas, G.

    2012-11-01

    The corrosion behavior originated by sulfate-reducing bacteria (SRB) was studied in two regions of welded API X-70 steel pipeline. The studies were focused on base material (BM) and heat affected zone (HAZ), from the internal region of the pipe. SRB were extracted from oil and grown in a Postgate medium. Corrosion was evaluated at 60 degree centigrade for times between 5 and 64 days. Potentiodynamic polarization curves, obtained by electrochemical techniques, indicated surface activation at short times. Structural and morphological characterizations were carried out by scanning electron microscopy (SEM) and optical microscopy (OM). H{sub 2}S concentration and pH were also measured. Results showed an important increase in the corrosion damage up to 20 days, influenced by the SRB activity, which lead to a maximum of H{sub 2}S (pH minimum). It was found a localized corrosion attack in the HAZ in a higher quantity compared to BM; and the formation of a thin film on the steel surface, originated by corrosion products and bacterial activity. (Author) 15 refs.

  9. Desarrollo de los procesos de moldeo por inyección y extrusión de polvos para la obtención de piezas de aceros inoxidables dúplex y ferríticos

    OpenAIRE

    Sotomayor Lozano, María Eugenia

    2011-01-01

    En la presente Tesis Doctoral se ha desarrollado el proceso de moldeo por inyección de polvos (pIM) para la obtención de piezas de acero inoxidable dúplex con aplicaciones en ortodoncia. Por otro lado, se ha desarrollado el proceso de moldeo por extrusión de polvos (PEM) para la obtención de láminas y tubos porosos de acero inoxidable ferrítico con aplicaciones en pilas de combustible de óxido sólido (SOFCs). En primer lugar, se prepararon y caracterizaron térmica y reológicamente las mezclas...

  10. El acero que nunca se fundió. Una reseña sobre Stalin

    Directory of Open Access Journals (Sweden)

    Iñaki Oneca Agurruza

    2004-02-01

    Full Text Available Era el 5 de marzo de 1953 cuando murió el fetiche, el gurú, el símbolo. Stalin significa “acero”, y precisamente una de las cosas que se reprochó al joven revolucionario, tras la adopción de este apodo, era que el acero era duro pero también frío. Así iniciamos esta breve nota sobre la figura de uno de los personajes clave del siglo XX.

  11. Quality Assurance statistics for AVHRR Pathfinder Version 5.2 L3-Collated (L3C) sea surface temperature in global and selected regions (NODC Accession 0111871)

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — These quality monitoring data for Pathfinder Version 5.2 (PFV5.2) Sea Surface Temperature (SST) are based on the concept of a Rich Inventory developed by the...

  12. Comportamento higiênico em colmeias de Apis mellifera L. africanizadas no Sertão da Paraíba

    Directory of Open Access Journals (Sweden)

    F. A. Olinto

    2015-12-01

    Full Text Available A apicultura é uma das poucas atividades agropecuárias que atende aos três requisitos da sustentabilidade: o econômico, o social e o ecológico. Sendo assim, fornece renda para o apicultor, ocupa mão de obra familiar ou contratada e contribui para a preservação da flora nativa. A sanidade pode afetar o desenvolvimento da apicultura, pois a Apis mellifera como qualquer outro organismo vivo, é susceptível a doenças causadas por bactérias, vírus, fungos e outros parasitas e as desordens metabólicas, nutricionais e hormonais, além de intoxicações diversas. Assim, em virtude da necessidade de estudos a respeito da sanidade apícola, objetiva-se estudar o comportamento higiênico em colônias de abelhas Apis mellifera em apiários localizados no Sertão do Estado da Paraíba. A pesquisa foi realizada no período de março, abril e maio de 2014, em cinco apiários localizados nos municípios de Condado, Pombal, Jericó, São Bentinho e São Domingos, ambos situados na Mesorregião do Sertão do Estado da Paraíba, com um total de 25 colmeias avaliadas. O teste de comportamento higiênico foi realizado com base no método de perfuração das células de crias. O percentual de comportamento higiênico foi semelhante em ambos os apiários, principalmente em Condado (93,96%, Pombal (94,30%, Jericó (87,63% e São Domingos (95,20%, ocorrendo apenas uma ligeira diferença no apiário de São Bentinho com uma média de 76,31%. O apiário localizado no município de Pombal obteve o melhor resultado, apresentando índice elevado de comportamento higiênico. Hygienic behavior in Apis mellifera L. africanized hives in the Backlands of ParaibaAbstract: Beekeeping is one of the few agricultural activities that meets the three requirements of sustainability: economic, social and ecological. Therefore, provides income for the beekeeper, occupies family labor or hired and contributes to the preservation of native flora. Sanity may affect the

  13. Classical conditioning of proboscis extension in harnessed Africanized honey bee queens (Apis mellifera L.).

    Science.gov (United States)

    Aquino, Italo S; Abramson, Charles I; Soares, Ademilson E E; Fernandes, Andrea Cardoso; Benbassat, Danny

    2004-06-01

    Experiments are reported on learning in virgin Africanized honey bee queens (Apis mellifera L.). Queens restrained in a "Pavlovian harness" received a pairing of hexanal odor with a 1.8-M feeding of sucrose solution. Compared to explicitly unpaired controls, acquisition was rapid in reaching about 90%. Acquisition was also rapid in queens receiving an unconditioned stimulus of "bee candy" or an unconditioned stimulus administered by worker bees. During extinction the conditioned response declines. The steepest decline was observed in queens receiving an unconditioned stimulus of bee candy. These findings extend previous work on learning of Afrianized honey bee workers to a population of queen bees.

  14. X-ray diffraction study of microstructural changes during fatigue damage initiation in steel pipes

    Energy Technology Data Exchange (ETDEWEB)

    Pinheiro, B., E-mail: bianca@lts.coppe.ufrj.br [Laboratory of Mechanics of Lille (LML), UMR CNRS 8107, University of Lille 1, Boulevard Paul Langevin, Cite Scientifique, 59655 Villeneuve d' Ascq (France); Lesage, J. [Laboratory of Mechanics of Lille (LML), UMR CNRS 8107, University of Lille 1, Boulevard Paul Langevin, Cite Scientifique, 59655 Villeneuve d' Ascq (France); Pasqualino, I. [Subsea Technology Laboratory (LTS), Ocean Engineering Department, COPPE/Federal University of Rio de Janeiro, PO Box 68508, Cidade Universitaria, CEP 21945-970, Rio de Janeiro/RJ (Brazil); Benseddiq, N. [Laboratory of Mechanics of Lille (LML), UMR CNRS 8107, University of Lille 1, Boulevard Paul Langevin, Cite Scientifique, 59655 Villeneuve d' Ascq (France); Bemporad, E. [Interdepartmental Laboratory of Electron Microscopy (LIME), University of Rome TRE, Via Della Vasca Navale 79, 00146 Rome (Italy)

    2012-01-15

    Highlights: Black-Right-Pointing-Pointer In this work we study the fatigue damage evolution in an API 5L X60 steel. Black-Right-Pointing-Pointer Microstructural changes and residual stresses are evaluated during fatigue tests. Black-Right-Pointing-Pointer Microdeformations and macro residual stresses are estimated by X-ray diffraction. Black-Right-Pointing-Pointer Results are discussed in view of an indicator of fatigue damage initiation. Black-Right-Pointing-Pointer This indicator could allow the prediction of residual life before macrocracking. - Abstract: Steel pipes used in the oil and gas industry undergo the action of cyclic loads that can cause their failure by fatigue. A consistent evaluation of the fatigue damage during the initiation phase should fundamentally be based on a nanoscale approach, i.e., at the scale of the dislocation network, in order to take into account the micromechanisms of fatigue damage that precede macrocrack initiation and propagation until the final fracture. In this work, microstructural changes related to fatigue damage initiation are investigated in the API 5L X60 grade steel, used in pipe manufacturing. Microdeformations and macro residual stress are evaluated using X-ray diffraction in real time during alternating bending fatigue tests performed on samples cut off from an X60 steel pipe. The aim of this ongoing work is to provide ground for further development of an indicator of fatigue damage initiation in X60 steel. This damage indicator could allow a good residual life prediction of steel pipes previously submitted to fatigue loading, before macroscopic cracking, and help to increase the reliability of these structures.

  15. Structural, thermal, spectroscopic and magnetic studies of the (C2N2H10)0.5[Fe xV1-x(HPO3)2] (x = 0.26, 0.52, 0.74) solid solution

    International Nuclear Information System (INIS)

    Cisneros, Jose L.; Fernandez-Armas, Sergio; Mesa, Jose L.; Pizarro, Jose L.; Arriortua, Maria I.; Rojo, Teofilo

    2006-01-01

    The (C 2 N 2 H 10 ) 0.5 [Fe x V 1-x (HPO 3 ) 2 ] (x = 0.26, 0.52 0.74) compounds have been obtained by mild solvothermal conditions in the form of micro-crystalline powder with brown color. The crystal structures were refined by X-ray powder diffraction data using the Rietveld method. The compounds crystallize in the monoclinic system, space group P2/c with the unit-cell parameters, a = 9.262(5) A, b = 8.823(5) A, c = 9.714(6) A, β = 120.84(3) o ; a = 9.245(1) A, b = 8.823(1) A, c = 9.698(1)A, β = 120.80(1) o and, a = 9.254(4)A, b = 8.822(4)A, c = 9.702(4)A, β = 120.73(3) o for (C 2 N 2 H 10 ) 0.5 [Fe 0.26 V 0.74 (HPO 3 ) 2 ] (1) (C 2 N 2 H 10 ) 0.5 [Fe 0.52 V 0.48 (HPO 3 ) 2 ] (2), and (C 2 N 2 H 10 ) 0.5 [Fe 0.74 V 0.26 (HPO 3 ) 2 ] (3). The compounds show an open crystalline structure with three-dimensional character, whose formula for the anionic inorganic skeleton is [M(HPO 3 ) 2 ] 2- . The inorganic framework is formed by [MO 6 ] octahedra inter-connected by phosphite groups. The structure of the compounds exhibits channels extended along the [1 0 0] and [0 0 1] directions and the ethylendiammonium cations are located inside these channels, linked through hydrogen bonds and ionic interactions. The infrared spectra show the bands corresponding to the stretching (P-H) vibration of the phosphite group and the band corresponding to the deformation mode of the ethylendiammonium cation, δ(NH 3 + ). The thermal and thermodiffractometric behavior show that the compounds are stable up to approximately 300 deg. C, at higher temperatures the decomposition of the crystal structure by calcination of the organic cation starts. The diffuse reflectance spectra show bands of the V 3+ ion (d 2 ), and a band of the Fe 3+ ion (d 5 ), in a slightly distorted octahedral symmetry. The values of the Dq and Racah parameters (B and C) have been calculated for the V(III) cation. Magnetic measurements were performed on a powdered sample from 5 to 300 K at magnetic fields 1000, 500

  16. Influencia de la atmósfera de sinterización en las propiedades mecánicas de los aceros P/M AISI 430L

    Directory of Open Access Journals (Sweden)

    Iglesias, F. Javier

    2014-03-01

    Full Text Available It has studied the stainless steel powder metallurgy AISI 430L. It has compared the sintering in two different atmospheres; in vacuum, and in an atmosphere containing nitrogen. It has developed a heat treatment with the aim of improving the mechanical properties. This has been done through microstructural modification of complex nitrides of iron and chromium precipitates during the phase of sintering. Physical properties have been evaluated and are been performing a microstructural analysis for microstructure related to the increase in mechanical properties.Se ha estudiado el acero inoxidable pulvimetalúrgico AISI 430L, comparando la sinterización en dos atmósferas diferentes; en vacío, y en una atmósfera que contiene nitrógeno. Se ha desarrollado un tratamiento térmico con objeto de incrementar las propiedades mecánicas, mediante la modificación microestructural de los nitruros complejos de hierro y cromo precipitados durante la etapa de sinterización. Se han evaluado las propiedades físicas y a la vez se ha realizado un análisis microestructural con el fin de relacionar la microestructura con el incremento en las propiedades mecánicas.

  17. Honey Bees (Apis mellifera, L.) as Active Samplers of Airborne Particulate Matter.

    Science.gov (United States)

    Negri, Ilaria; Mavris, Christian; Di Prisco, Gennaro; Caprio, Emilio; Pellecchia, Marco

    2015-01-01

    Honey bees (Apis mellifera L.) are bioindicators of environmental pollution levels. During their wide-ranging foraging activity, these hymenopterans are exposed to pollutants, thus becoming a useful tool to trace the environmental contaminants as heavy metals, pesticides, radionuclides and volatile organic compounds. In the present work we demonstrate that bees can also be used as active samplers of airborne particulate matter. Worker bees were collected from hives located in a polluted postmining area in South West Sardinia (Italy) that is also exposed to dust emissions from industrial plants. The area is included in an official list of sites of national interest for environmental remediation, and has been characterized for the effects of pollutants on the health of the resident population. The head, wings, hind legs and alimentary canal of the bees were investigated with Scanning Electron Microscopy coupled with X-ray spectroscopy (SEM-EDX). The analyses pointed to specific morphological and chemical features of the particulate, and resulted into the identification of three categories of particles: industry-, postmining-, and soil-derived. With the exception of the gut, all the analyzed body districts displayed inorganic particles, mostly concentrated in specific areas of the body (i.e. along the costal margin of the fore wings, the medial plane of the head, and the inner surface of the hind legs). The role of both past mining activities and the industrial activity close to the study area as sources of the particulate matter is also discussed. We conclude that honey bees are able to collect samples of the main airborne particles emitted from different sources, therefore could be an ideal tool for monitoring such a kind of pollutants.

  18. Desarrollo de un cerrojo artificial para el skin-pass en una línea de acero galvanizado por inmersión en caliente

    Directory of Open Access Journals (Sweden)

    González-Marcos, A.

    2008-02-01

    Full Text Available In this paper, we present the application of data mining techniques to develop an “artificial lock” for the skin-pass in an attempt to solve a problem that can arise during the galvanising manufacturing process: the wrong labelling of the steel grade of a coil. In order to detect these errors and thus to avoid that coils with different properties than expected end up with a client, we propose neural network-based models for on-line predicting the strip elongation in the skin-pass section according to the manufacturing conditions and its chemical composition. Thus, a significant difference between estimated and measured elongation would mean that the coil must be removed from the line for further analyses.

    En este trabajo se presenta la aplicación de técnicas de minería de datos en el desarrollo de un “cerrojo artificial” para el skin-pass, que permita solucionar un problema que puede presentarse en la fabricación de bobinas de acero galvanizado: el etiquetado incorrecto del grado de acero de una bobina. Para tratar de detectar estos errores y evitar así que los clientes reciban bobinas con propiedades distintas de las esperadas, se proponen modelos, basados en redes neuronales, que predicen on-line el alargamiento de las bobinas en el skin-pass en función de las variables del proceso de fabricación y de su composición química. De esta forma, si la diferencia entre el alargamiento que estima el modelo y el medido realmente es significativa, se hace necesario sacar la bobina de la línea para someterla a análisis más exhaustivos.

  19. CARACTERIZACIÓN CUALITATIVA DEL POLEN RECOLECTADO POR Apis mellifera L EN TRES APIARIOS DEL MUNICIPIO DE POPAYÁN QUALITATIVE CHARACTERIZATION OF THE GATHERED POLLEN FOR Apis mellifera L IN THREE APIARIES IN THE MUNICIPALITY OF POPAYAN

    Directory of Open Access Journals (Sweden)

    NELSON JOSÉ VIVAS

    2008-12-01

    Full Text Available Durante los meses de Junio, Julio, Agosto y Septiembre de año 2006, se realizó un estudio de melisopalinología, en tres veredas del municipio de Popayán, con el fin de determinar la flora apícola predominante en la zona, se analizaron los tipos polínicos recolectados por las abejas Apis mellifera y los botones florales recolectados en campo durante la época de estudio mediante el método de Acetolisis láctica; de cuarenta tipos polínicos recolectados, mediante microscopía se identificaron 24 en el polen de las colmenasDuring months of June, July, August September in 2006, a study of melisopalinology was developed in three places near Popayán, aiming to determine the predominant apian flora in the study zone. The pollen types recollected by Apis mellifera and the flower blooms collected on the field during the study were analyzed using the Lactic Acetolysis technique. From the 40 types of pollen collected, by means of microscopy only 24 were identified among the pollen found in the beehives

  20. The quantum Hall effect at 5/2 filling factor

    International Nuclear Information System (INIS)

    Willett, R L

    2013-01-01

    Experimental discovery of a quantized Hall state at 5/2 filling factor presented an enigmatic finding in an established field of study that has remained an open issue for more than twenty years. In this review we first examine the experimental requirements for observing this state and outline the initial theoretical implications and predictions. We will then follow the chronology of experimental studies over the years and present the theoretical developments as they pertain to experiments, directed at sets of issues. These topics will include theoretical and experimental examination of the spin properties at 5/2; is the state spin polarized? What properties of the higher Landau levels promote development of the 5/2 state, what other correlation effects are observed there, and what are their interactions with the 5/2 state? The 5/2 state is not a robust example of the fractional quantum Hall effect: what experimental and material developments have allowed enhancement of the effect? Theoretical developments from initial pictures have promoted the possibility that 5/2 excitations are exceptional; do they obey non-abelian statistics? The proposed experiments to determine this and their executions in various forms will be presented: this is the heart of this review. Experimental examination of the 5/2 excitations through interference measurements will be reviewed in some detail, focusing on recent results that demonstrate consistency with the picture of non-abelian charges. The implications of this in the more general physics picture is that the 5/2 excitations, shown to be non-abelian, should exhibit the properties of Majorana operators. This will be the topic of the last review section. (review article)

  1. 40 CFR 52.379 - Control strategy: PM2.5.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 3 2010-07-01 2010-07-01 false Control strategy: PM2.5. 52.379 Section 52.379 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) APPROVAL AND PROMULGATION OF IMPLEMENTATION PLANS Connecticut § 52.379 Control strategy: PM2.5. Approval...

  2. Indonesian honey protein isolation Apis dorsata dorsata and Tetragonula sp. as antibacterial and antioxidant agent

    Science.gov (United States)

    Sahlan, Muhamad; Damayanti, Vina; Azizah, Nurul; Hakamada, Kazuaki; Yohda, Masafumi; Hermansyah, Heri; Wijanarko, Anondho; Rohmatin, Etin

    2018-02-01

    Honey is a natural product that has many properties and been widely used for many theurapeutic purposes. Research on honey has been very rapid but not yet for Indonesia. Like local Indonesian honey Apis dorsata dorsata and Tetragonula sp. which has been widely consumed by the public but not yet known for certain efficacy of each content. The function of honey as antibacterial and antioxidant has not been specifically explained by the components contained in honey. Protein is one of the content of honey that turned out to have activity as an antibacterial and antioxidant in certain types of honey because of it antimicrobial peptide. Testing of honey activity as antibacterial and antioxidant through several stages including isolation, SDS-PAGE analysis, Bradford test, antibacterial activity test with well diffusion method and antioxidant activity test by DPPH method. Bacteria used were gram-positive bacteria Staphylococcus aureus and gram negative Escherichia coli. After some experiment finally got protein isolation method that is in the form of further concentration using Millipore membrane for honey Tetragonula sp. and membrane filtration dot blot for honey Apis dorsata dorsata. The Bradford assay showed that Apis dorsata dorsata honey contains protein <5 µg / ml, while honey Tetragonula sp. has a protein content of 97 µg / ml. The characteristic profile of molecular weight of the protein showed honey Tetragonula sp. has 3 protein bands composed of 52, 96 - 61,9 kDa, 63,35 - 65,92 kDa and 86,16 - 91,4 kDa, whereas Apis dorsata dorsata honey has 5 protein bands consisting of 45,2 - 46,6 kDa, 50,2 - 50,9 kDa, 62,5 - 62,9 kDa, 73,1 - 73,9 kDa, 83,9 - 86,9 kDa. Isolate honey protein Apis dorsata dorsata has no antioxidant and antibacterial activity (Staphylococcus aureus and Escherichia coli), whereas honey protein isolates Tetragonula sp. has antibacterial activity against Escherichia coli.

  3. Diseño y construcción de un prototipo controlado para carburización gaseosa de aceros utilizando alcoholes

    OpenAIRE

    Obando B, Johnny F; Castro P, Álvaro; Trujillo, Carlos Alexander

    2010-01-01

    En esta investigación se realizó el diseno, construcción y prueba de un equipo a escala de laboratorio para tratamientos térmicos con atmósfera controlada para el estudio de la carburización gaseosa de aceros con alcoholes. El equipo posee las siguientes caracterIsticas: producción controlada de una atmósfera gaseosa compuesta hasta por tres gases y dos lIquidos volatiles, una zona de reacción isotérmica, inerte y hermética, y una zona de analisis de gases que retiene sólidos y lIquidos cond...

  4. A monitoring study to assess the acute mortality effects of indoxacarb on honey bees (Apis mellifera L.) in flowering apple orchards

    NARCIS (Netherlands)

    Steen, van der J.J.M.; Dinter, A.

    2007-01-01

    To evaluate the effect of the indoxacarb 300 g kg-1 WG, Steward 30WDGTM, on the honey bee (Apis mellifera L.) in apple orchards, a monitoring study was conducted in Dutch apple orchards in April/May 2004. Before apple flowering began, two honey bee colonies were placed in each orchard to investigate

  5. Effect of Microstructure on HIC Susceptibility of API X70MS Linepipe Steel

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Joon-Ho; Sim, Ho-Seop; Park, Byung-Gyu [Dongkuk Steel R and D Center, Pohang (Korea, Republic of); Cho, Kyung-Mox [Pusan National University, Busan (Korea, Republic of)

    2017-06-15

    The resistance of hydrogen induced cracking (HIC) was investigated with different microstructures of API X70MS steel. Ferrite/acicular ferrite (F/AF), deformed ferrite/acicular ferrite, ferrite/bainite (F/B) and single acicular ferrite (AF) were obtained by thermo-mechanical controlled process (TMCP) with changing rolling and cooling conditions. HIC resistance was found to be affected by the type as well as morphology of the microstructure, and thus the behavior of crack initiation and propagation could be analyzed. It was found that single AF and deformed F/AF with uniformly distributed dislocation reduced HIC initiation. Banded microstructure with a hardness value below 250 HV, such as AF, showed good HIC propagation resistance due to high toughness. AF generally exhibited excellent crack initiation and propagation resistance, namely the best HIC susceptibility performance. AF might redeem the HIC resistance for the banded microstructure also.

  6. Delocalization and occupancy effects of 5f orbitals in plutonium intermetallics using L3-edge resonant X-ray emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Booth, C. H.; Medling, S. A.; Jiang, Yu; Bauer, E. D.; Tobash, P. H.; Mitchell, J. N.; Veirs, D. K.; Wall, M. A.; Allen, P. G.; Kas, J. J.; Sokaras, D.; Nordlund, D.; Weng, T. -C.

    2014-06-24

    Although actinide (An) L3 -edge X-ray absorption near-edge structure (XANES) spectroscopy has been very effective in determining An oxidation states in insulating, ionically bonded materials, such as in certain coordination compounds and mineral systems, the technique fails in systems featuring more delocalized 5f orbitals, especially in metals. Recently, actinide L3-edge resonant X-ray emission spec- troscopy (RXES) has been shown to be an effective alternative. This technique is further demonstrated here using a parameterized partial unoccupied density of states method to quantify both occupancy and delocalization of the 5f orbital in ?-Pu, ?-Pu, PuCoGa5 , PuCoIn5 , and PuSb2. These new results, supported by FEFF calculations, highlight the effects of strong correlations on RXES spectra and the technique?s ability to differentiate between f-orbital occupation and delocalization.

  7. DIRAC RESTful API

    International Nuclear Information System (INIS)

    Casajus Ramo, A; Graciani Diaz, R; Tsaregorodtsev, A

    2012-01-01

    The DIRAC framework for distributed computing has been designed as a flexible and modular solution that can be adapted to the requirements of any community. Users interact with DIRAC via command line, using the web portal or accessing resources via the DIRAC python API. The current DIRAC API requires users to use a python version valid for DIRAC. Some communities have developed their own software solutions for handling their specific workload, and would like to use DIRAC as their back-end to access distributed computing resources easily. Many of these solutions are not coded in python or depend on a specific python version. To solve this gap DIRAC provides a new language agnostic API that any software solution can use. This new API has been designed following the RESTful principles. Any language with libraries to issue standard HTTP queries may use it. GSI proxies can still be used to authenticate against the API services. However GSI proxies are not a widely adopted standard. The new DIRAC API also allows clients to use OAuth for delegating the user credentials to a third party solution. These delegated credentials allow the third party software to query to DIRAC on behalf of the users. This new API will further expand the possibilities communities have to integrate DIRAC into their distributed computing models.

  8. 48 CFR 52.246-5 - Inspection of Services-Cost-Reimbursement.

    Science.gov (United States)

    2010-10-01

    ...-Cost-Reimbursement. 52.246-5 Section 52.246-5 Federal Acquisition Regulations System FEDERAL... Provisions and Clauses 52.246-5 Inspection of Services—Cost-Reimbursement. As prescribed in 46.305, insert... furnishing of services, when a cost-reimbursement contract is contemplated: Inspection of Services—Cost...

  9. Development of API 5 CT grade P110 steel casing; Desenvolvimento de tubos casing API 5 CT grau P110

    Energy Technology Data Exchange (ETDEWEB)

    Kojima, Sergio Seijo; Roza, Juliana Espinossi

    2003-07-01

    This paper has as objective to discuss the results gotten in experiences carried through in industrial scale for the development of pipes class API 5CT P110 (1), with 244 mm of diameter and 12 mm of thickness. The pipes were welded longitudinally by process ERW (electric resistance welding) and submitted to quenching and tempering heat treatments. A C-Mn-Cr alloy with adequate quenching ability was used for the attainment of a martensite microstructure after quenching. The pipes at a temperature of 880 deg C were quenched in water and subsequently tempered at 515 deg C. The integrity of the weld region was evaluated through non destructive tests and flattening tests, Charpy impact tests and fracture toughness tests (CTOD). The pipes achieved the tension properties stipulated in the standard (yield strength bigger limit of 758 Mpa), and also the energy in the Charpy impact test (transversal), considering that the energy value obtained was 55 J (at 0 deg C) for base metal and 44 J in the weld metal. (author)

  10. Determinación de los parámetros de corrosión y desgaste del par acero/aluminio en presencia de líquidos iónicos

    OpenAIRE

    Jerez Mesa, Ramón

    2008-01-01

    El presente proyecto presenta resultados obtenidos en ensayos utilizando LI combinados con aluminio 2011 y acero F-1310, tanto en ensayos de corrosión como de tribología. Escuela Técnica Superior de Ingeniería Industrial

  11. Clinical reactivity of celery cultivars in allergic patients: Role of Api g 1.

    Science.gov (United States)

    Dölle, S; Welter, S; Ruppel, E; Lehmann, K; Schwarz, D; Jensen-Jarolim, E; Zieglmayer, P; Franken, P; Worm, M

    2018-04-01

    Celery (Apium graveolens L.) is a vegetable consumed world-wide. Celery stalks and celeriac roots are often ingredients in convenient food products like spice blends and soups. In this study, we examined the allergenicity of distinct celeriac cultivars. Sixteen celery-allergic patients were identified using a double-blind, placebo-controlled food challenge. Ten different celeriac cultivars were used for skin prick testing in the patients. Two cultivars were further applied for oral food challenges; their protein composition was analysed by immunoblotting, and contents of major allergen Api g 1 were quantified. From the 10 investigated celeriac cultivars, two cultivars elicited significantly different skin reactivity ("Anita": 5.0 [2.0-12.0] mm vs "Prinz": 7.0 [3.0-9.5] mm; P = .047). Moreover, "Anita" induced fewer symptoms after a controlled oral-celeriac challenge in 14 patient (P Api g 1 in "Prinz" than in "Anita." Taken together, the data from this study suggest that cultivar Anita is better tolerated in celery-allergic patients than "Prinz." Differences in the protein expression profile between the cultivars, particularly the different content of Api g 1, could cause the different allergenicity. © 2018 John Wiley & Sons Ltd.

  12. Determination of Bortezomib in API Samples Using HPLC: Assessment of Enantiomeric and Diastereomeric Impurities.

    Science.gov (United States)

    Kamalzadeh, Zahra; Babanezhad, Esmaeil; Ghaffari, Solmaz; Mohseni Ezhiyeh, Alireza; Mohammadnejad, Mahdieh; Naghibfar, Mehdi; Bararjanian, Morteza; Attar, Hossein

    2017-08-01

    A new, normal phase high performance liquid chromatography (NP-HPLC) method was developed for separation of Bortezomib (BZB) enantiomers and quantitative determination of (1S,2R)-enantiomer of BZB in active pharmaceutical ingredient (API) samples. The developed method was validated based on International Conference on Harmonisation (ICH) guidelines and it was proved to be accurate, precise and robust. The obtained resolution (RS) between the enantiomers was more than 2. The calibration curve for (1S,2R)-enantiomer was found to be linear in the concentration range of 0.24-5.36 mg/L with regression coefficient (R2) of 0.9998. Additionally, the limit of detection (LOD) and limit of quantification (LOQ) were 0.052 and 0.16 mg/L, respectively. Also, in this study, a precise, sensitive and robust gradient reversed-phase HPLC (RP-HPLC) method was developed and validated for determination of BZB in API samples. The detector response was linear over the concentration range of 0.26-1110.5 mg/L. The values of R2, LOD and LOQ were 0.9999, 0.084 and 0.25 mg/L, respectively. For both NP-HPLC and RP-HPLC methods, all of the RSD (%) values obtained in the precision study were 2,000 and RS > 2.0. The performance of two common integration methods of valley to valley and drop perpendicular for drawing the baseline between two adjacent peaks were investigated for the determination of diastereomeric impurity (Imp-D) in the BZB-API samples. The results showed that the valley to valley method outperform the drop perpendicular method for calculation of Imp-D peak areas. Therefore, valley to valley method was chosen for peak integration. © The Author 2017. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. Noise temperature of an NbN hot-electron bolometric mixer at frequencies from 0.7 THz to 5.2 THz

    International Nuclear Information System (INIS)

    Schubert, J.; Semenov, A.; Gol'tsman, G.; Huebers, H-W.; Voronov, B.; Gershenzon, E.; Schwaab, G.

    1999-01-01

    We report on noise temperature measurements of an NbN phonon-cooled hot-electron bolometric mixer in the terahertz frequency range. The devices were 3 nm thick films with in-plane dimensions 1.7x0.2μm 2 and 0.9x0.2μm 2 integrated in a complementary logarithmic-spiral antenna. Measurements were performed at seven frequencies ranging from 0.7 THz to 5.2 THz. The measured DSB noise temperatures are 1500 K (0.7 THz), 2200 K (1.4 THz), 2600 K (1.6 THz), 2900 K (2.5 THz), 4000 K (3.1 THz), 5600 K (4.3 THz) and 8800 K (5.2 THz). (author)

  14. Taxa de Infestação da Varroa destructor em colônias de Apis mellifera L. no Agreste Meridional de Pernambuco

    Directory of Open Access Journals (Sweden)

    Deygnon Cavalcanti Clementino

    2016-08-01

    Full Text Available O presente trabalho teve como objetivo verificar a taxa de infestação da Varroa destructor em colônias de Apis mellifera L. proveniente de apiário no município de Lagoa do Ouro, Agreste Meridional de Pernambuco. A pesquisa foi realizada no mês de setembro de 2015. Participaram do estudo 15 colônias, em que foram coletadas em média 227 abelhas adultas de cada colmeia e acondicionadas em recipientes contendo álcool a 70%. Após as coletas a campo, as amostras foram transportadas para o laboratório de Biologia Animal da Universidade Federal Rural de Pernambuco/Unidade Acadêmica de Garanhuns, para a realização das análises e quantificação dos ácaros. Os resultados demonstraram que 100% das amostras estavam parasitadas com o ácaro, sendo que a média geral da taxa de infestação foi de 6,16%. O grau de infestação pela Varroa destructor observado nas colônias variou de 0,93% a 11,15%. Conclui-se que as colônias analisadas apresentam diferentes níveis de infestação pelo ácaro Varroa destructor.Infestation rate of Varroa destructor in Apis mellifera L. colonies in the South Agreste of PernambucoAbstract: This study aimed to verify the infestation rate of Varroa destructor in Apis mellifera L. colonies in the apiary from Lagoa do Ouro County, South Agreste of Pernambuco. The survey was conducted in September 2015. The study included 15 colonies, which were collected on average 227 adult bees in each hive and placed in vials containing 70% alcohol. After harvesting the field, the samples were transported to the Animal Biology Laboratory at the Federal Rural University of Pernambuco/Academic Unit of Garanhuns, to perform the analysis and quantification of mites. The results showed that 100% of the samples were infested with mites, and the overall average infestation rate was 6.16%. The degree of infestation by Varroa destructor observed in colonies ranged from 0.93% to 11.15%. It is concluded that the analyzed colonies have

  15. X-ray fluorescence cross sections for K and L x rays of the elements

    International Nuclear Information System (INIS)

    Krause, M.O.; Nestor, C.W. Jr.; Sparks, C.J. Jr.; Ricci, E.

    1978-06-01

    X-ray fluorescence cross sections are calculated for the major x rays of the K series 5 less than or equal to Z less than or equal to 101, and the three L series 12 less than or equal to Z less than or equal to 101 in the energy range 1 to 200 keV. This calculation uses Scofield's theoretical partical photoionization cross sections, Krause's evaluation of fluorescence and Coster-Kronig yields, and Scofield's theoretical radiative rates. Values are presented in table and graph format, and an estimate of their accuracy is made. The following x rays are considered: Kα 1 , Kα 1 , 2 , Kβ 1 , Kβ 1 , 3 , Lα 1 , Lα 1 , 2 , Lβ 1 , Lβ 2 , 15 , Lβ 3 , Ll, Lγ 1 , Lγ 4 , and L 1 → L 2 , 3 . For use in x-ray fluorescence analysis, Kα and Lα fluorescence cross sections are presented at specific energies: TiK identical with 4.55 keV, CrK identical with 5.46 keV, CoK identical with 7.00 keV, CuK identical with 8.13 keV, MoKα identical with 17.44 keV, AgK identical with 22.5 keV, DyK identical with 47.0 keV, and 241 Am identical with 59.54 keV. Supplementary material includes fluorescence and Coster--Kronig yields, fractional radiative rates, fractional fluorescence yields, total L-shell fluorescence cross sections, fluorescence and Coster-Kronig yields in condensed matter, effective fluorescence yields, average L-shell fluorescence yield, L-subshell photoionization cross section ratios, and conversion factors from barns per atom to square centimeters per gram

  16. Influencia del Calor Aportado y Metal de Aporte Sobre las Propiedades Mecánicas y la Microestructura de Juntas Soldadas por FCAW de Acero Microaleado de Alta Resistencia

    Directory of Open Access Journals (Sweden)

    César Marconi

    2015-06-01

    Full Text Available ResumenActualmente, los aceros microaleados son ampliamente utilizados en reemplazo de los aceros al C y C-Mn por sus ventajas en cuanto a propiedades mecánicas, resistencia a la corrosión y soldabilidad, permitiendo una reducción de peso de los vehículos y estructuras sin detrimento de su resistencia. Cuando estos aceros son soldados, el ciclo térmico de la soldadura provoca cambios microestructurales que modifican sus propiedades originales. El calor aportado (HI: heat input es una de las principales variables a tener en cuenta cuando se evalúan estas modificaciones. Las propiedades finales de la unión soldada también se definen por el tipo de consumible utilizado. El objetivo de este trabajo es analizar las propiedades mecánicas y la microestructura de juntas soldadas a tope de un acero microaleado con dos grados de metal de aporte y diferentes HI. Como resultado del trabajo se observó un aumento considerable de tamaño de grano en la ZAC adyacente a la línea de fusión para todas las condiciones, siendo este efecto más marcado cuando se soldó con alto HI; y un ablandamiento en la ZAC de grano fino. Prácticamente se mantuvieron los valores de resistencia a la tracción al soldar con ambos consumibles, con un mejor desempeño cuando se soldó con bajo HI. La tenacidad en la ZAC mejoró con la disminución del HI.

  17. Desenvolvimento e produção de pólen em colméias de Apis mellifera L. africanizadas mantidas em cultura de girassol

    Directory of Open Access Journals (Sweden)

    Danilo Freitas da Silva

    2011-05-01

    Full Text Available Foram alojadas oito colméias Langstroth com coletor de pólen modelo alvado, mantidas em uma área de 5 ha de lavoura de girassol (Hellianthus annuus L., distribuídas em dois tratamentos: alimento energético (açúcar invertido ou alimento protéico (açúcar refinado+açúcar invertido+farinha láctea - 6:3:1. O objetivo deste trabalho foi avaliar a alimentação energética ou protéica e o desenvolvimento de colônias de abelhas Apis mellifera L., durante a produção de pólen em cultura de girassol. Foram avaliadas: área de cria, área de mel, área de pólen e produção de pólen das colmeias. O suplemento energético proporcionou maior (P

  18. AVHRR Pathfinder Version 5.2 Level 3 Collated (L3C) Global 4km Sea Surface Temperature for 1981-2012

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The AVHRR Pathfinder Version 5.2 Sea Surface Temperature data set (PFV52) is a collection of global, twice-daily 4km sea surface temperature data produced in a...

  19. Inorganic inhibitor study in the steel corrosion in the mixture of LiBr+Etilenglicol+H{sub 2}O; Estudio de inhibidores inorganicos en la corrosion de aceros en la mezcla de LiBr+Etilenglicol+H{sub 2}O

    Energy Technology Data Exchange (ETDEWEB)

    Sarmiento Bustos, Estela

    2008-07-15

    develop this work. Fourth chapter is the results presentation and discussion divided in four sections: each one for material electrochemically tested in the LiBr+ etilene glycol+ H{sub 2}O solution. Also presents the results obtained for the extended study made to carbon steel under different temperature and electrochemical test conditions. This includes the EIS and electrochemical noise Hurst results analysis and simulations. Finally, the fifth chapter presents the conclusions and recommendations of this work. An appendix with the solution preparation is included. [Spanish] En esta tesis doctoral se presentan los resultados obtenidos de cinetica electroquimica de la corrosion de 4 aceros: acero al carbon, 304, 316 y 316L, en una solucion de LiBr+ etilenglicol+H{sub 2}O. Estos sistemas son utilizados en bombas de calor por absorcion para la recuperacion de calor de desecho a la salida de procesos industriales. Sin embargo, la solucion absorbente es altamente corrosiva en este tipo de equipos. Por lo anterior se evaluaron tres diferentes inhibidores inorganicos: nitrato de litio, molibdato de litio y cromato de litio los cuales son fuertes oxidantes y promueven la formacion de la capa pasiva de los aceros y se aplicaron a diferentes temperaturas: 25, 50 y 80 grados dentigrados. A traves de tecnicas electroquimicas como curvas de polarizacion, ruido electroquimico, impedancia electroquimica, resistencia a la polarizacion lineal y mediciones de potencial de corrosion a circuito abierto en el tiempo. Se determino el compuesto inhibidor mas adecuado obteniendo su eficiencia bajo las diferentes condiciones, de los tres inhibidores considerados el que presento el mejor comportamiento y eficiencia para el acero al carbon fue el nitrato de litio a 50 ppm; para el 304 el cromato de litio a 5 ppm; para el acero 316 molibdato de litio a 5 ppm y para el 316L el cromato de litio a 5 ppm. Debido a que el acero al carbon es el material mas economico y presento una mejor respuesta por

  20. Study on the food distribution among workers of different races of the honeybee Apis mellifica L. by means of the 32P radioisotope

    International Nuclear Information System (INIS)

    Kloft, W.J.; Djalal, A.S.; Drescher, Wilhelm

    1976-01-01

    Using the radioactive tracer-technique, the social food distribution among workerbees of different races of the honeybee Apis mellifica L. to workerbees of Apis cerana Fabr. was studied. The experiments were carried out under standardized conditions as age, groupsize, food-supply of the donor-bee, distribution-time and temperature. Significant differences in the time required for social food distributions among workerbees of the different races were demonstrated. The highest number of acceptor-bees during 4 hours belonged to A.m.ligustica. A.m. caucasica reached similar values, A.m. carnica was intermediate, while A.m. mellifica was the slowest distributor. This foodsharing behavior was compared with other differences in the activity of different bee races

  1. Uso da parafina incorporada à cera alveolada em colônias de abelhas Apis mellifera L. africanizadas para produção de mel Paraffin incorporation to beewax foundation in Apis mellifera L. Africanized colonies for honey production

    Directory of Open Access Journals (Sweden)

    Vagner de Alencar Arnaut de Toledo

    2002-04-01

    Full Text Available O objetivo foi avaliar favos construídos a partir de três tratamentos, lâminas de cera alveolada, lâminas de cera alveolada com parafina e parte do quadro sem cera. Foram utilizadas dez colônias de abelhas africanizadas, Apis mellifera L. (Hymenoptera, Apidae existentes na região de Marialva, Estado do Paraná. Foram efetuados mapeamentos da área construída e ocupada com mel, a intervalos de aproximadamente 20 dias. Três quadros, cada um contendo os três tratamentos foram colocados nas posições lateral esquerda, central e lateral direita da melgueira vista por trás da colméia. As abelhas construíram a maior área e ocuparam com mel (p The aim of this paper was the evaluation of combs from three experimental treatments: beeswax foundation, beeswax with paraffin and a gap frame, partially without wax. The experiment was carried out using ten Apis mellifera L. (Hymenoptera, Apidae Africanized honeybee colonies in Marialva - state of Paraná, in the south of Brazil. They were accomplished by mapping areas constructed and occupied with honey, at intervals of approximately 20 days. Three combs, containing, each one, the three treatments were placed at the positions right lateral, central and left lateral of the super observed the hive to the back. The honeybees built the greatest area and filled with honey (p < 0.05 when the comb was introduced in the central position of the hive, compared to other treatments in which differences were also observed (p < 0.05. The position of the wax comb mixed with paraffin produced the smallest area (p < 0.05 occupied with honey compared to the others. Results showed that paraffin mixed with wax comb should be used since the combs are placed in the central position and must be used for production of honey in sections.

  2. Fatigue crack growth rate of API X70 steel pipelines under spectrum loading

    International Nuclear Information System (INIS)

    Beden, S.M.; Abdullah, S.; Ariffin, A.K.

    2012-01-01

    Pipelines offer the most efficient way to transport bulk quantities of gas and oil, either from points of production to storage locations or from storage locations to distributed points of end use. As one of the main materials of west–east gas transmission pipes, X70 pipelines usually serve under variable amplitude loading (VAL). Base on the importance of in-service API X70 pipelines, it is important for the safe operation of this system to know its behaviour under VAL. This paper focuses on the ability of using the NASGRO model to predict the fatigue crack growth (FCG), based on investigation with the modified Wheeler model and experimental data. The results show that the NASGRO model give a fatigue life near by to that published in literatures and also showed the FCG rate response of X70 pipeline steels when exposed to VAL with different overload values. Extra modification to the NASGRO model may lead to better representing of FCG rate. Highlights: ► The assessment of fatigue crack propagation under different load histories are proposed and presented in this paper. ► Due to lack of knowledge in the related area, as yet no universal model exists. ► The output was based on both simulation and experiments. The simulation part was carried out based on the NASGRO model. ► This work focus on fatigue crack growth (FCG) and fatigue life based on the comparison with the previous work.

  3. Diseño y construcción de un prototipo controlado para carburización gaseosa de aceros utilizando alcoholes

    OpenAIRE

    Obando B, Johnny F.; Castro P., Álvaro; Trujillo, Carlos Alexander

    2006-01-01

    En esta investigación se realizó el diseño, construcción y prueba de un equipo a escala de laboratorio para tratamientos térmicos con atmósfera controlada para el estudio de la carburización gaseosa de aceros con alcoholes. El equipo posee las siguientes características: producción controlada de una atmósfera gaseosa compuesta hasta por tres gases y dos líquidos volátiles, una zona de reacción isotérmica, inerte y hermética, y una zona de análisis de gases que retiene sólidos y líquidos conde...

  4. L-shell ionization in Au by O5+ -and Ni5+ -ion impact

    International Nuclear Information System (INIS)

    Goyal, D.P.; Singh, B.P.; Verma, H.R.

    1995-01-01

    The L X-ray production cross sections in gold by 60 to 72 MeV O 5+ ions and 58 to 87 MeV Ni 5+ -ions have been measured. The L-subshell ionization cross sections derived from these experimental results have been compared with the direct ionization theories viz. plane wave Born approximation (PWBA) theory and modified perturbed-stationary-state theory with energy loss, Coulomb deflection and relativistic effects (MECPSSR). A new procedure has been described to account for the change in the yield ratio Lβ 1 /Lβ 2.15 with energy, for Ni 5+ -ion impact on gold. The L sub-shell ionization cross sections have been derived from Lβ 1 , Lβ 4 and Lβ 2.15 lines of the Lβ group in addition to those calculated by the conventional Datz TRY3 technique using Lα, Lγ 1 and Lγ 2.3 X-ray lines. From the shift in the energies of various L X-ray lines and changes in their intensities, 3 and 5 spectator vacancies in the M-and N-shells in gold have been estimated with O 5+ -ion impact while 7, 20 and 4 to 6 spectator vacancies have been inferred in the M-, N- and O-shells respectively with Ni 5+ -ion impact in the energy range of the projectiles undertaken in the present studies. (orig.)

  5. Advanced API security securing APIs with OAuth 2.0, OpenID Connect, JWS, and JWE

    CERN Document Server

    Siriwardena, Prabath

    2014-01-01

    Advanced API Security is a complete reference to the next wave of challenges in enterprise security--securing public and private APIs. API adoption in both consumer and enterprises has gone beyond predictions. It has become the 'coolest' way of exposing business functionalities to the outside world. Both your public and private APIs, need to be protected, monitored and managed. Security is not an afterthought, but API security has evolved a lot in last five years. The growth of standards, out there, has been exponential. That's where AdvancedAPI Security comes in--to wade through the weeds

  6. 16QAM transmission with 5.2 bits/s/Hz spectral efficiency over transoceanic distance.

    Science.gov (United States)

    Zhang, H; Cai, J-X; Batshon, H G; Davidson, C R; Sun, Y; Mazurczyk, M; Foursa, D G; Pilipetskii, A; Mohs, G; Bergano, Neal S

    2012-05-21

    We transmit 160 x 100 G PDM RZ 16 QAM channels with 5.2 bits/s/Hz spectral efficiency over 6,860 km. There are more than 3 billion 16 QAM symbols, i.e., 12 billion bits, processed in total. Using coded modulation and iterative decoding between a MAP decoder and an LDPC based FEC all channels are decoded with no remaining errors.

  7. Effect of Thermomechanical Processing and Crystallographic Orientation on the Corrosion Behavior of API 5L X70 Pipeline Steel

    Science.gov (United States)

    Ohaeri, Enyinnaya; Omale, Joseph; Eduok, Ubong; Szpunar, Jerzy

    2018-04-01

    This work presents the electrochemical response of X70 pipeline steel substrates thermomechanically processed at different conditions. The WE sample was hot rolled at a temperature range of 850 °C to 805 °C and cooled at a rate of 42.75 °C/s. Another sample WD was hot rolled from 880 °C to 815 °C and cooled at a faster rate of 51.5 °C/s. Corrosion tests were conducted electrochemically by potentiodynamic polarization in hydrogen-charged and non-hydrogen-charged environments. A lower corrosion rate was measured with hydrogen charging due to the rapid formation of corrosion product film on pipeline substrate, but WE specimen emerged as the most susceptible to corrosion with and without hydrogen charging. Variations in thermomechanical rolling conditions influenced grain orientation, protective film properties, corrosion, and cracking behavior on both specimens. Cracks were seen in both specimens after hydrogen charging, but specimen WE experienced a more intense deterioration of protective corrosion product film and subsequent cracking. A large part of specimen WD retained its protective corrosion product film after the polarization test, and sites where spalling occurred resulted in pitting with less cracking. Despite weak crystallographic texture noticed in both specimens, WD showed a higher intensity of corrosion-resistant 111||ND-oriented grains, while WE showed a more random distribution of 111||ND-, 011||ND-, and 001||ND-oriented grains with a lower intensity.

  8. Effect of Thermomechanical Processing and Crystallographic Orientation on the Corrosion Behavior of API 5L X70 Pipeline Steel

    Science.gov (United States)

    Ohaeri, Enyinnaya; Omale, Joseph; Eduok, Ubong; Szpunar, Jerzy

    2018-06-01

    This work presents the electrochemical response of X70 pipeline steel substrates thermomechanically processed at different conditions. The WE sample was hot rolled at a temperature range of 850 °C to 805 °C and cooled at a rate of 42.75 °C/s. Another sample WD was hot rolled from 880 °C to 815 °C and cooled at a faster rate of 51.5 °C/s. Corrosion tests were conducted electrochemically by potentiodynamic polarization in hydrogen-charged and non-hydrogen-charged environments. A lower corrosion rate was measured with hydrogen charging due to the rapid formation of corrosion product film on pipeline substrate, but WE specimen emerged as the most susceptible to corrosion with and without hydrogen charging. Variations in thermomechanical rolling conditions influenced grain orientation, protective film properties, corrosion, and cracking behavior on both specimens. Cracks were seen in both specimens after hydrogen charging, but specimen WE experienced a more intense deterioration of protective corrosion product film and subsequent cracking. A large part of specimen WD retained its protective corrosion product film after the polarization test, and sites where spalling occurred resulted in pitting with less cracking. Despite weak crystallographic texture noticed in both specimens, WD showed a higher intensity of corrosion-resistant 111|| ND-oriented grains, while WE showed a more random distribution of 111|| ND-, 011|| ND-, and 001|| ND-oriented grains with a lower intensity.

  9. 25 Tb/s transmission over 5,530 km using 16QAM at 5.2 b/s/Hz spectral efficiency.

    Science.gov (United States)

    Cai, J-X; Batshon, H G; Zhang, H; Davidson, C R; Sun, Y; Mazurczyk, M; Foursa, D G; Sinkin, O; Pilipetskii, A; Mohs, G; Bergano, Neal S

    2013-01-28

    We transmit 250x100G PDM RZ-16QAM channels with 5.2 b/s/Hz spectral efficiency over 5,530 km using single-stage C-band EDFAs equalized to 40 nm. We use single parity check coded modulation and all channels are decoded with no errors after iterative decoding between a MAP decoder and an LDPC based FEC algorithm. We also observe that the optimum power spectral density is nearly independent of SE, signal baud rate or modulation format in a dispersion uncompensated system.

  10. Multilevel Thoracolumbar Spondylolysis with Spondylolisthesis at L4 on L5.

    Science.gov (United States)

    Kim, Whoan Jeang; Song, Young Dong; Choy, Won Sik

    2015-09-01

    A 24-year-old male patient was initially evaluated for persistent back pain. The visual analogue scale (VAS) score was 7 points. Physical examination revealed a decreased range of lumbar spinal motion, which caused pain. Simple X-ray revealed Meyerding grade 1 spondylolisthesis at L4 on L5, with mild dome-shaped superior endplate and consecutive multilevel spondylolysis at T12-L5. Standing anteroposterior and lateral views of the entire spine revealed normal balance of sagittal and coronal alignment. A computed tomography scan revealed bilateral spondylolysis at T12-L4, left unilateral spondylolysis at L5, and spina bifida at L5 to sacral region. Magnetic resonance imaging revealed mild dural ectasia at the lumbar region. Due to the absence of any neurological symptoms, the patient was managed conservatively. He was rested a few weeks with corset brace and physiotherapy. After treatment, his back pain improved, VAS score changed from 7 to 2, and he was able to return to normal activity.

  11. Twin-Wire Pulsed Tandem Gas Metal Arc Welding of API X80 Steel Linepipe

    Directory of Open Access Journals (Sweden)

    Wenhao Wu

    2018-01-01

    Full Text Available Twin-Wire Pulsed Tandem Gas Metal Arc Welding process with high welding production efficiency was used to join the girth weld seam of API X80 steel linepipe of 18.4 mm wall thickness and 1422 mm diameter. The macrostructure, microstructure, hardness, and electrochemical corrosion behavior of welded joints were studied. Effects of temperature and Cl− concentration on the corrosion behavior of base metal and weld metal were investigated. Results show that the welded joint has good morphology, mechanical properties, and corrosion resistance. The corrosion resistance of both the base metal and the weld metal decreases with increasing temperature or Cl− concentration. In the solution with high Cl− concentration, the base metal and weld metal are more susceptible to pitting. The corrosion resistance of the weld metal is slightly lower than that of the base metal.

  12. Oxidación en vapor de agua del acero inoxidable aisi 317 a 700 y 750ºc

    OpenAIRE

    MARULANDA AREVALO, JOSE LUDDEY; REMOLINA MILLAN, ADULJAY; BARON, JAIRO ALBERO

    2013-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

  13. OXIDACIÓN EN VAPOR DE AGUA DEL ACERO INOXIDABLE AISI 317 A 700 Y 750ºC

    OpenAIRE

    José Luddey Marulanda Arevalo; Aduljay Remolina Millan; Jairo Alberto Barón

    2013-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI SAE 317, a temperaturas de 700 y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento a la corrosión. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de Microscopia Electrónica de Barrido (SEM) y difracción de rayos X (DRX), para observar cómo se forman las capas de óxidos y discutir el posible mecanismo de oxidación en vapor de agua. Se encontró que el mecanismo de...

  14. Assessment of off-stoichiometric Zr33-xFe52+xSi15 C14 Laves phase compounds as permanent magnet materials

    Science.gov (United States)

    Gabay, A. M.; Hadjipanayis, G. C.

    2018-05-01

    Recently, Fe-based rare-earth-free compounds with non-cubic crystal structures were proposed as a base for permanent magnets which would not rely on critical elements. In this work, two series of alloys, Zr27Fe73-wSiw (0 ≤ w ≤ 15) and Zr33-xFe52+xSi15 (0 ≤ x ≤ 11), were prepared and characterized after annealing at 1538 K in order to determine the fundamental magnetic properties of the C36 and C14 hexagonal Laves phase compounds. A mixture of the cubic C15 and Zr6Fe23 structures was observed instead of the expected C36 structure. The hexagonal C14 was found in all Zr33-xFe52+xSi15 alloys with its lattice parameters linearly decreasing as the Fe(Si) atoms occupy the Zr sites in the Laves phase crystal structure. The solubility limit of Fe in the C14 structure at 1538 K corresponds to x = 9.5. The Curie temperature of the C14 compounds increases with deviation from the Laves phase stoichiometry from 290 K to 530 K. The room-temperature spontaneous magnetization also increases reaching, after correcting for the non-magnetic impurities, a value of 6.7 kG. The magnetocrystalline anisotropy of the off-stoichiometric C14 Laves phase was found to be uniaxial with the easy magnetization direction parallel to the hexagonal axis. Unfortunately, the anisotropy field, which does not exceed 10 kOe, is not sufficiently high to make the compounds interesting as permanent magnet materials.

  15. Aumento en la resistencia a la corrosión de un acero t91 aluminizado

    OpenAIRE

    QUINTERO, LUZ S.; LAVERDE, DIONISIO; ESCALANTE, HUMBERTO

    2011-01-01

    El acero ferrítico T91 ha sido ampliamente utilizado en plantas de generación de energía eléctrica, calderas y plantas nucleares. Sin embargo, su resistencia a la oxidación se ve gravemente afectada a temperaturas superiores a los 600ºC. En esta investigación se empleó la técnica de cementación empacada para aluminizar un acero T91 y se encontraron las condiciones óptimas para la formación de un recubrimiento libre de porosidad y con espesor uniforme (300 micras). Se evaluó la capa de óxido f...

  16. Influence of sand movement in the Sahara on the erosion of pipeline network

    Directory of Open Access Journals (Sweden)

    Azari Z.

    2010-06-01

    Full Text Available The influence of sandblasting on a surface notched of pipeline with API 5L X52 steel is studied. The purpose of this study is to determine the evolution of static characteristics and lifetime of material in both directions of pipeline (Longitudinal (L and Transverse (T. Specimens were taken from a pipeline and the material damage was made by projecting corundum particles (aluminium oxide. In order to justify the evolution of mechanical properties of material, residual stress analysis was realized by the technique of X-ray diffraction. The observation of damage mode and distribution of residual stress under the notch tip show that the material hardening, the notch radius and the compressive stress, play together an important role in stabilizing the material mechanical properties.

  17. Exact Quantization of the Even-Denominator Fractional Quantum Hall State at ν =5/2 Landau Level Filling Factor

    International Nuclear Information System (INIS)

    Pan, W.; Tsui, D.C.; Pan, W.; Xia, J.; Shvarts, V.; Adams, D.E.; Xia, J.; Shvarts, V.; Adams, D.E.; Stormer, H.L.; Stormer, H.L.; Pfeiffer, L.N.; Baldwin, K.W.; West, K.W.

    1999-01-01

    We report ultralow temperature experiments on the obscure fractional quantum Hall effect at Landau level filling factor ν=5/2 in a very high-mobility specimen of μ=1.7x10 7 cm 2 /V s . We achieve an electron temperature as low as ∼4 mK , where we observe vanishing R xx and, for the first time, a quantized Hall resistance, R xy =h/(5/2)e 2 to within 2ppm. R xy at the neighboring odd-denominator states ν=7/3 and 8/3 is also quantized. The temperature dependences of the R xx minima at these fractional fillings yield activation energy gaps Δ 5/2 =0.11 , Δ 7/3 =0.10 , and Δ 8/3 =0.055 K . copyright 1999 The American Physical Society

  18. Macelignan inhibits bee pathogenic fungi Ascophaera apis growth through HOG1 pathway

    Directory of Open Access Journals (Sweden)

    Y.K. Shin

    2016-01-01

    Full Text Available Ascosphaera apis is a bee pathogen that causes bee larvae infection disease, to which treatment is not yet well investigated. The aim of this study was to investigate antifungal susceptibility in vitro against A. apis and to identify a new antifungal agent for this pathogen through minimal inhibitory concentration (MIC assay and western blot analysis. Macelignan had 1.56 and 3.125 μg/mL MIC against A. apis after 24 and 48 h, respectively, exhibiting the strongest growth inhibition against A. apis among the tested compounds (corosolic acid, dehydrocostus lactone, loganic acid, tracheloside, fangchinoline and emodin-8-O-β-D-glucopyranoside. Furthermore, macelignan showed a narrow-ranged spectrum against various fungal strains without any mammalian cell cytotoxicity. In spite of miconazole having powerful broad-ranged anti-fungal activity including A. apis, it demonstrated strong cytotoxicity. Therefore, even if macelignan alone was effective as an antifungal agent to treat A. apis, combined treatment with miconazole was more useful to overcome toxicity, drug resistance occurrence and cost effectiveness. Finally, HOG1 was revealed as a target molecule of macelignan in the anti-A. apis activity by inhibiting phosphorylation using S. cerevisiae as a model system. Based on our results, macelignan, a food-grade antimicrobial compound, would be an effective antifungal agent against A. apis infection in bees.

  19. Fenómenos de corrosión galvánica en las uniones aluminio y acero

    OpenAIRE

    Domínguez Parra, Alberto

    2009-01-01

    La corrosión es un proceso de degradación de un material al interactuar con el ambiente que le rodea. El presente proyecto trata de la corrosión galvánica de aceros y fundiciones, en contacto con aleaciones de aluminio. Su experimentación se ha realizado con acero AE 275 B, y fundición EN-GS 400 12. Se utilizó lingote de aluminio A356 obtenido por colada por gravedad, y dos tipos de muestras, con y sin tratamiento térmico T6, de A 356 producidas por el procedimiento de sub-liquidus casting...

  20. Open Astronomy Catalogs API

    Science.gov (United States)

    Guillochon, James; Cowperthwaite, Philip S.

    2018-05-01

    We announce the public release of the application program interface (API) for the Open Astronomy Catalogs (OACs), the OACAPI. The OACs serve near-complete collections of supernova, tidal disruption, kilonova, and fast stars data (including photometry, spectra, radio, and X-ray observations) via a user-friendly web interface that displays the data interactively and offers full data downloads. The OACAPI, by contrast, enables users to specifically download particular pieces of the OAC dataset via a flexible programmatic syntax, either via URL GET requests, or via a module within the astroquery Python package.

  1. Phase development and dielectric properties of (1-x)Pb(Zr0.52Ti0.48)O3-xBaTiO3 ceramics

    International Nuclear Information System (INIS)

    Chaisan, Wanwilai; Yimnirun, Rattikorn; Ananta, Supon; Cann, David P.

    2006-01-01

    (1-x)Pb(Zr 0.52 Ti 0.48 )O 3 -xBaTiO 3 ceramics were prepared by a modified mixed-oxide method. The phase formation was studied by XRD analysis. All compositions exhibit complete solid solutions of perovskite-like phase in the (1-x)PZT-xBT system. The (2 0 0)/(0 0 2) peak was found to split at the composition x = 0.6 and the co-existence of tetragonal-rhombohedral phases occurs with x ≤ 0.6. The possible range of compositions which correspond to a phase transition is 0.6 < x < 0.7. While pure BT ceramics exhibited a sharp phase transformation expected for normal ferroelectrics, phase transformation behavior of the (1-x)PZT-xBT solid solutions became more diffuse with increasing BT contents. This was primarily evidenced by an increased broadness in the dielectric peak, with a maximum peak width occurring at x = 0.5

  2. Web API Fragility : How Robust is Your Web API Client

    NARCIS (Netherlands)

    Espinha, T.; Zaidman, A.; Gross, H.G.

    2014-01-01

    Web APIs provide a systematic and extensible approach for application-to-application interaction. A large number of mobile applications makes use of web APIs to integrate services into apps. Each Web API’s evolution pace is determined by their respective developer and mobile application developers

  3. Recubrimientos de (ti,aln sobre acero aisi 4140 por sputtering reactivo

    Directory of Open Access Journals (Sweden)

    DANNA GARCIA

    2007-01-01

    Full Text Available Empleando la técnica de Pulverización catódica con radiofrecuencia y magnetrón (Magnetron Sputtering RF, se prepararon películas de (Ti,AlN sobre sustratos de acero AISI 4140. Se utilizó un blanco formado con polvos metálicos de Ti y Al, con composición nominal 60% Ti y 40% Al (porcentaje en átomos y una razón de presiones parciales de nitrógeno - argón, PN2/PAr de 0,1 aproximadamente; la temperatura del sustrato se varió entre 260 y 330 ºC y el tiempo de deposición entre 2 y 4,5 horas para obtener películas con diferentes espesores. La composición química de las películas se determinó mediante la técnica de energía dispersada de rayos X (EDX, y su topografía mediante microscopía de fuerza atómica (AFM. Igualmente se midió micro dureza, y se determinó su comportamiento electroquímico mediante espectroscopia de impedancia electroquímica EIS y ensayos TAFEL. Las películas obtenidas presentaron granos globulares, uniformes y de pequeño diámetro, con características electroquímicas de protección al sustrato frente a procesos de corrosión.

  4. Healthcare Finder API

    Data.gov (United States)

    U.S. Department of Health & Human Services — All of the data used on the Finder.HealthCare.gov web application is available through this API. There are multiple collections of data available through the API. 1....

  5. ELi 52 miljardist saab lõviosa keskkond / Hindrek Riikoja

    Index Scriptorium Estoniae

    Riikoja, Hindrek

    2006-01-01

    Ilmunud ka: Postimees : na russkom jazõke 13. veebr. lk. 3. Euroopa Liidu struktuurifondidest Eestile aastateks 2007-2013 eraldatavast 52 miljardist kroonist läheb esialgse kava kohaselt 13,4 miljardit krooni keskkonnale, 11 miljardit haridusküsimuste lahendamiseks ning 11,8 miljardit ettevõtluse ja teaduse arendamiseks. Diagramm: Euroraha saajad

  6. Uso de zangões (Apis mellifera L.) na detecção de cera de abelha adulterada

    OpenAIRE

    Maurizete da Cruz Silva; Italo de Souza Aquino; Charles Ira Abramson; José Wellington dos Santos

    2000-01-01

    Esta pesquisa avaliou a habilidade de zangões da abelha africanizada (Apis mellifera L.) em detectar cera de abelha adulterada usando o reflexo da extensão da probóscide (PER). Duzentos e quarenta zangões foram divididos em 12 grupos contendo níveis diferentes de cera de abelha adulterada (100% cera de abelha, 90% cera de abelha, 10% cera de abelha, 0% cera de abelha). Um estímulo de ar foi incluído como testemunha devido à possível influência do fluxo de ar per se. Os animais foram mantidos ...

  7. Structural variations and dielectric properties of (Bi1-xL ax ) 2Si O5 (0 ≤x ≤0.1 ): Polycrystallines synthesized by crystallization of Bi-Si-O and Bi-La-Si-O glasses

    Science.gov (United States)

    Taniguchi, Hiroki; Tatewaki, Shingo; Yasui, Shintaro; Fujii, Yasuhiro; Yamaura, Jun-ichi; Terasaki, Ichiro

    2018-04-01

    This paper focuses on effects of isovalent La substitution on the crystal structure and dielectric properties of ferroelectric B i2Si O5 . Polycrystalline samples of (Bi1-xL ax ) 2Si O5 are synthesized by crystallization of Bi-Si-O and Bi-La-Si-O glasses with a composition range of 0 ≤x ≤0.1 . The crystal structure changes from monoclinic to tetragonal with increasing La-substitution rate x at room temperature. This structural variation stems from the change in orientation of Si O4 tetrahedra that form one-dimensional chains when they are in the ordered configuration, thus suggesting that lone-pair electrons play an important role in sustaining one-dimensional chains of Si O4 tetrahedra. Synchronizing with the disordering of Si O4 chains, ferroelectric phase transition temperature of (Bi1-xL ax ) 2Si O5 sharply decreases as x increases, and ferroelectricity finally vanishes at around x =0.03 . The present results demonstrate that lone-pair electrons of Bi play an important role in the ferroelectricity of B i2Si O5 through propping the ordered structure of one-dimensional Si O4 chains with stereochemical activity. Furthermore, an additional phase transition has been first discovered in the low-temperature region of (Bi1-xL ax ) 2Si O5 with x ≤0.01 , where the ordered one-dimensional Si O4 chains remain.

  8. Characterizing the Impact of Commercial Pollen Substitute Diets on the Level of Nosema spp. in Honey Bees (Apis mellifera L.)

    OpenAIRE

    Fleming, James C.; Schmehl, Daniel R.; Ellis, James D.

    2015-01-01

    Western honey bee (Apis mellifera L.) populations face declines commonly attributed to pesticide, pathogen, and parasite stress. One way beekeepers combat these stressors is by providing supplemental protein diets to honey bee colonies to ensure adequate colony nutrition. However Nosema spp., a microsporidian parasite of the honey bee, is thought to be associated closely with a colony's nutritional intake, thus possibly negating any benefit the bees otherwise would have received from a nutrit...

  9. Mating Frequencies of Honey Bee Queens (Apis mellifera L.) in a Population of Feral Colonies in the Northeastern United States

    OpenAIRE

    Tarpy, David R.; Delaney, Deborah A.; Seeley, Thomas D.

    2015-01-01

    Across their introduced range in North America, populations of feral honey bee (Apis mellifera L.) colonies have supposedly declined in recent decades as a result of exotic parasites, most notably the ectoparasitic mite Varroa destructor. Nonetheless, recent studies have documented several wild populations of colonies that have persisted. The extreme polyandry of honey bee queens-and the increased intracolony genetic diversity it confers-has been attributed, in part, to improved disease resis...

  10. 27 CFR 5.52 - Certificates of age and origin.

    Science.gov (United States)

    2010-04-01

    ... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Certificates of age and origin. 5.52 Section 5.52 Alcohol, Tobacco Products and Firearms ALCOHOL AND TOBACCO TAX AND TRADE BUREAU, DEPARTMENT OF THE TREASURY LIQUORS LABELING AND ADVERTISING OF DISTILLED SPIRITS Requirements for Withdrawal...

  11. Fluidos iónicos en lubricación de contactos aluminio-acero : interacciones superficiales y triboquímicas

    OpenAIRE

    Jiménez Ballesta, Ana Eva

    2009-01-01

    Los líquidos iónicos (LI) son fluidos de altas prestaciones con un amplio rango de estabilidad térmica. Actualmente están siendo objeto de estudio en una gran variedad de contactos, siendo una de sus aplicaciones tribológicas más interesante la lubricación del contacto aluminio-acero. En este trabajo se estudia la influencia de la longitud de la cadena lateral del catión y de la naturaleza del anión sobre la capacidad lubricante de 6 LI derivados del catión imidazolio, un derivado de piridini...

  12. Study of the flight range and ideal density of the africanized honeybees, Apis mellifera L., 1758 (Hymenoptera: Apidae) labelled with {sup 32} P on an apple orchard; Estudo do raio de acao e densidade ideal de abelhas africanizadas, Apis mellifera L., 1758 (Hymenoptera: Apidae) marcadas com {sup 32} P em pomar de maca

    Energy Technology Data Exchange (ETDEWEB)

    Paranhoa, B A.J.

    1990-06-01

    The ideal density, the flight range, the choice for any flight direction, the influence of temperature and relative humidity of air about the honeybee`s activity, Apis mellifera L.. 1758 (Hymenoptera: Apidae) were studied in an apple orchard, utilizing nuclear techniques. Five hives, with 35,000 bees each, were labelled with syrup (50%) content (2,5 {mu}Ci {sup 32} P/ml) and taken one by one, every two days to the blossomed orchard. A circumference area of 100 m diameter (0,8 ha) W staked each 10 m from the center to the limit (50 m), making a cross, pointing out to North, South, East and West. The honeybees were collected on apple flowers, during 5 minutes in each stake, at 10:00 a.m. and 12:30 p.m. (author).

  13. Standard methods for Apis mellifera propolis research

    Science.gov (United States)

    Propolis is one of the most fascinating honey bee (Apis mellifera L.) products. It is a plant derived product that bees produce from resins that they collect from different plant organs and with which they mix beeswax. Propolis is a building material and a protective agent in the beehive. It also pl...

  14. Quantification of toxins in a Cry1Ac?+?CpTI cotton cultivar and its potential effects on the honey bee Apis mellifera L.

    OpenAIRE

    Han, Peng; Niu, Chang-Ying; Lei, Chao-Liang; Cui, Jin-Jie; Desneux, Nicolas

    2010-01-01

    Transgenic Cry1Ac?+?CpTI cotton (CCRI41) is increasingly planted throughout China. However, negative effects of this cultivar on the honey bee Apis mellifera L., the most important pollinator for cultivated ecosystem, remained poorly investigated. The objective of our study was to evaluate the potential side effects of transgenic Cry1Ac?+?CpTI pollen from cotton on young adult honey bees A. mellifera L. Two points emphasized the significance of our study: (1) A higher expression level of inse...

  15. Composition Dependence of the Na(+) Ion Conductivity in 0.5Na2S + 0.5[xGeS2 + (1 - x)PS5/2] Mixed Glass Former Glasses: A Structural Interpretation of a Negative Mixed Glass Former Effect.

    Science.gov (United States)

    Martin, Steve W; Bischoff, Christian; Schuller, Katherine

    2015-12-24

    A negative mixed glass former effect (MGFE) in the Na(+) ion conductivity of glass has been found in 0.5Na2S + 0.5[xGeS2 + (1 - x)PS5/2] glasses where the Na(+) ion conductivity is significantly smaller for all of the ternary glasses than either of the binary end-member glasses. The minimum conductivity of ∼0.4 × 10(-6) (Ω cm)(-1) at 25 °C occurs for the x = 0.7 glass. Prior to this observation, the alkali ion conductivity of sulfide glasses at constant alkali concentration, but variable ratio of one glass former for another (x) ternary mixed glass former (MGF) glasses, has always produced a positive MGFE in the alkali ion conductivity; that is, the ternary glasses have always had higher ion conductivities that either of the end-member binary glasses. While the Na(+) ion conductivity exhibits a single global minimum value, the conductivity activation energy exhibits a bimodal double maximum at x ≈ 0.4 and x ≈ 0.7. The modified Christensen-Martin-Anderson-Stuart (CMAS) model of the activation energies reveals the origin of the negative MGFE to be due to an increase in the dielectric stiffness (a decrease in relative dielectric permittivity) of these glasses. When coupled with an increase in the average Na(+) ion jump distance and a slight increase in the mechanical stiffness of the glass, this causes the activation energy to go through maximum values and thereby produce the negative MGFE. The double maximum in the conductivity activation energy is coincident with double maximums in CMAS calculated strain, ΔES, and Coulombic, ΔEC, activation energies. In these ternary glasses, the increase in the dielectric stiffness of the glass arises from a negative deviation of the limiting high frequency dielectric permittivity as compared to the binary end-member glasses. While the CMAS calculated total activation energies ΔEact = ΔES + ΔEC are found to reproduce the overall shape of the composition dependence of the measured ΔEact values, they are consistently

  16. Influencia sobre los tratamientos térmicos del contenido de aluminio de aceros no aleados

    Directory of Open Access Journals (Sweden)

    Carreras, L.

    1999-08-01

    Full Text Available The main purpose of this article is to determine the optimal level of aluminum content in plain steels to have the optimal mechanical properties by means of surface heat treatments. Various plain steels with different aluminium content have been studied. The importance of treatment temperature is analyzed. The influence of other factors, like nitrogen content or the homogenous distribution of particles, is evaluated. It is concluded that the aluminum composition of plain steels that are subjected to heat treatments should not exceed 0.02 %.

    El objetivo de este trabajo es determinar el intervalo óptimo de contenidos de aluminio en aceros no aleados para los que se consiguen las propiedades mecánicas óptimas mediante tratamientos térmicos de superficie. Se estudian diferentes coladas de acero en las que varía el contenido de aluminio y las temperaturas de tratamiento. Se evalúa la importancia de otros factores tales como el contenido de nitrógeno y la homogeneidad en la distribución de partículas endurecedoras. Se llega a la conclusión de que los aceros no aleados destinados a tratamientos térmicos no deben tener un contenido de aluminio superior al 0,02 %.

  17. Progress report on first year of WP5.2. Including detailed description of planned research for WP 5.2

    Energy Technology Data Exchange (ETDEWEB)

    Ellemers, N.; Van Dijk, E.; Terwel, B.; De Vries, G. [Leiden University, Leiden (Netherlands)

    2010-10-15

    This document contains the progress report on the first half year of the CATO-2 WP5.2 PhD project 'Framing effects in communication about CCS'. In the first few months a literature study has been conducted, both on (factors that influence) public perceptions and acceptance of CCS, and on framing. In the last two month, a first study was designed. This study consists of an experiment designed to examine how framing a company's involvement in CCS in terms of economic benefits and/or CSR of the organization affects the corporate image, trust, and perceived 'greenwashing' (deceit). Furthermore, this experiment serves to test the quality of newly developed questionnaires to measure these variables. In addition, this document contains a detailed description of the research planned for WP5.2 written by senior (CATO-2) researchers from January 2010 on. The objective of the research planned for WP5.2 is to examine whether framing of communications by an organization can improve the perceived credibility and trustworthiness of the organization and the information provided. This issue will be examined by a combination of experimental studies and a survey-type study.

  18. Transcriptome differences in the hypopharyngeal gland between Western Honeybees (Apis mellifera) and Eastern Honeybees (Apis cerana).

    Science.gov (United States)

    Liu, Hao; Wang, Zi-Long; Tian, Liu-Qing; Qin, Qiu-Hong; Wu, Xiao-Bo; Yan, Wei-Yu; Zeng, Zhi-Jiang

    2014-08-30

    Apis mellifera and Apis cerana are two sibling species of Apidae. Apis cerana is adept at collecting sporadic nectar in mountain and forest region and exhibits stiffer hardiness and acarid resistance as a result of natural selection, whereas Apis mellifera has the advantage of producing royal jelly. To identify differentially expressed genes (DEGs) that affect the development of hypopharyngeal gland (HG) and/or the secretion of royal jelly between these two honeybee species, we performed a digital gene expression (DGE) analysis of the HGs of these two species at three developmental stages (newly emerged worker, nurse and forager). Twelve DGE-tag libraries were constructed and sequenced using the total RNA extracted from the HGs of newly emerged workers, nurses, and foragers of Apis mellifera and Apis cerana. Finally, a total of 1482 genes in Apis mellifera and 1313 in Apis cerana were found to exhibit an expression difference among the three developmental stages. A total of 1417 DEGs were identified between these two species. Of these, 623, 1072, and 462 genes showed an expression difference at the newly emerged worker, nurse, and forager stages, respectively. The nurse stage exhibited the highest number of DEGs between these two species and most of these were found to be up-regulated in Apis mellifera. These results suggest that the higher yield of royal jelly in Apis mellifera may be due to the higher expression level of these DEGs. In this study, we investigated the DEGs between the HGs of two sibling honeybee species (Apis mellifera and Apis cerana). Our results indicated that the gene expression difference was associated with the difference in the royal jelly yield between these two species. These results provide an important clue for clarifying the mechanisms underlying hypopharyngeal gland development and the production of royal jelly.

  19. Impact of Nosema ceranae and Nosema apis on individual worker bees of the two host species (Apis cerana and Apis mellifera) and regulation of host immune response.

    Science.gov (United States)

    Sinpoo, Chainarong; Paxton, Robert J; Disayathanoowat, Terd; Krongdang, Sasiprapa; Chantawannakul, Panuwan

    Nosema apis and Nosema ceranae are obligate intracellular microsporidian parasites infecting midgut epithelial cells of host adult honey bees, originally Apis mellifera and Apis cerana respectively. Each microsporidia cross-infects the other host and both microsporidia nowadays have a worldwide distribution. In this study, cross-infection experiments using both N. apis and N. ceranae in both A. mellifera and A. cerana were carried out to compare pathogen proliferation and impact on hosts, including host immune response. Infection by N. ceranae led to higher spore loads than by N. apis in both host species, and there was greater proliferation of microsporidia in A. mellifera compared to A. cerana. Both N. apis and N. ceranae were pathogenic in both host Apis species. N. ceranae induced subtly, though not significantly, higher mortality than N. apis in both host species, yet survival of A. cerana was no different to that of A. mellifera in response to N. apis or N. ceranae. Infections of both host species with N. apis and N. ceranae caused significant up-regulation of AMP genes and cellular mediated immune genes but did not greatly alter apoptosis-related gene expression. In this study, A. cerana enlisted a higher immune response and displayed lower loads of N. apis and N. ceranae spores than A. mellifera, suggesting it may be better able to defend itself against microsporidia infection. We caution against over-interpretation of our results, though, because differences between host and parasite species in survival were insignificant and because size differences between microsporidia species and between host Apis species may alternatively explain the differential proliferation of N. ceranae in A. mellifera. Copyright © 2017 Elsevier Ltd. All rights reserved.

  20. Desgaste por deslizamiento en seco de aceros perlíticos y bainíticos

    Directory of Open Access Journals (Sweden)

    Cristian Camilo Viáfara Arango

    2004-01-01

    Full Text Available El desgaste por deslizamiento tiene una gran influencia sobre el desempeño de los sistemas rueda-riel, en particular, por el deslizamiento de la pestaña de la rueda sobre la parte interna del riel en una pista curva. Dado que el deslizamiento entre la rueda y el riel involucra efectos de adhesión, altos porcentajes de deslizamiento/rodadura afectan fuertemente el desgaste por fatiga de contacto por rodadura, que actúa en las superficies de contacto. En una máquina Pin sobre Disco se llevaron a cabo ensayos de desgaste por deslizamiento para estudiar el comportamiento del acero perlítico AISI 1070 y el bainítico AISI 15B30. La velocidad de deslizamiento fue 1 ms-1 para todas las pruebas y se utilizaron cargas normales de 10, 30 y 50 N. La resistencia al desgaste fue relacionada con la pérdida de masa medida después de las pruebas y las superficies desgastadas, al igual que las partículas removidas, fueron analizadas por medio de los microscopios óptico y electrónico. Se realizaron perfiles de microdureza bajo las superficies de contacto para analizar el efecto del endurecimiento por deformación. El acero perlítico mostró mayor resistencia al desgaste que el acero bainítico, debido al excelente comportamiento de endurecimiento por deformación de la perlita comparado con el de la bainita. En el acero perlítico se observaron regímenes de desgaste oxidativo, mientras que en el bainítico el principal mecanismo de remoción de material fue el adhesivo, llevando a un daño mucho más fuerte en la superficie. De hecho, el régimen de desgaste para las probetas bainíticas fue siempre severo, aún con la menor carga normal aplicada.

  1. Análisis de falla en cable de acero Análisis de falla en cable de acero

    Directory of Open Access Journals (Sweden)

    E. A. Ossa

    2005-12-01

    Full Text Available Este artículo describe el análisis de falla realizado en dos muestras de cables de acero que sufrieron falla súbita bajo condiciones de carga de trabajo normales. La falla fue causada por una carga menor a la capacidad nominal. Luego de inspección óptica se evidenció que la falla fue ocasionada por fatiga del material de uno de los cables.This paper describes the failure analysis of two wire ropes fractured during normal working conditions. The failure was caused by a load well below the nominal maximum resistance of the ropes. Optical microscopy indicated fatigue failure of one of the cables.

  2. Análisis de productos de corrosión de acero ,zinc, cobre y aluminio formados en clima polar antártico

    OpenAIRE

    Chico, Belén; Fuente, Daniel de la; Morcillo, Manuel; Almeida, E.; Joseph, Günter; Rivero, S.; Rosales, B.

    2002-01-01

    Este artículo presenta los resultados de caracterización de los productos de corrosión formados sobre acero, zinc, cobre y aluminio expuestos en estaciones de corrosión antárticas cercanas a la línea de costa, analizándose la influencia de las características singulares de este clima sobre la formación de los mismos. Los resultados se comparan con los obtenidos en atmósferas marinas de climas tropicales y templados.

  3. A qualitative examination of the content validity of the EQ-5D-5L in patients with type 2 diabetes.

    Science.gov (United States)

    Matza, Louis S; Boye, Kristina S; Stewart, Katie D; Curtis, Bradley H; Reaney, Matthew; Landrian, Amanda S

    2015-12-01

    The EQ-5D is frequently used to derive utilities for patients with type 2 diabetes (T2D). Despite widely available quantitative psychometric data on the EQ-5D, little is known about content validity in this population. Thus, the purpose of this qualitative study was to examine content validity of the EQ-5D in patients with T2D. Patients with T2D in the UK completed concept elicitation interviews, followed by administration of the EQ-5D-5L and cognitive interviewing focused on the instrument's relevance, clarity, and comprehensiveness. A total of 25 participants completed interviews (52.0 % male; mean age = 53.5 years). Approximately half (52 %) reported that the EQ-5D-5L was relevant to their experience with T2D. When asked if each individual item was relevant to their experience with T2D, responses varied widely (24.0 % said the self-care item was relevant; 68.0 % said the anxiety/depression item was relevant). Participants frequently said items were not relevant to themselves, but could be relevant to patients with more severe diabetes. Most participants (92.0 %) reported that T2D and/or its treatment/monitoring requirements had an impact on their quality of life that was not captured by the EQ-5D-5L. Common missing concepts included food awareness/restriction (n = 13, 52.0 %); activities (n = 11, 44.0 %); emotional functioning other than depression/anxiety (n = 8, 32.0 %); and social/relationship functioning (n = 8, 32.0 %). The results highlight strengths and potential limitations of the EQ-5D-5L, including missing content that could be important for some patients with T2D. Suggestions for addressing limitations are provided.

  4. Frecuencia de Varroa destructor, Nosema apis y Acarapis woodi en colonias manejadas y enjambres silvestres de abejas (Apis mellifera en Mérida, Yucatán, México

    Directory of Open Access Journals (Sweden)

    Jesús Froylán Martínez Puc

    2011-01-01

    Full Text Available Las enfermedades y parasitosis que afectan a las abejas melíferas causan importantes pérdidas económicas a la actividad apícola. Sin embargo, los daños provocados por dichas parasitosis se presentan de manera heterogénea en colonias manejadas y en enjambres silvestres. Con la finalidad de determinar la frecuencia y niveles de infestación de V. destructor, N. apis y A. woodi en abejas melíferas en Yucatán, se colectaron un total de 76 muestras de abejas melíferas, durante junio a septiembre de 2006, siendo 27 de colonias manejadas y 49 de enjambres silvestres. La frecuencia de V. destructor en colonias manejadas fue de 62.9 %, con un nivel de infestación de 1.70 ± 0.26 (ácaros/100 abejas, y en los enjambres silvestres fue de 55.1 %, con un nivel de infestación de 1.96 ± 0.44. No se observaron diferencias en la frecuencia (X2 = 0.44, gl = 1, P =0.51, y niveles de infestación (t=0.14, P=0.89. La frecuencia de N. apis en las colonias manejadas fue de 74.0 %, con una media de infestación de 1´480 x 103 ± 232 x 103 (esporas/ abeja, y en los enjambres silvestres de 53.0 %, con una media de infestación de 1´416 x 103 ± 264 x 103, no se observaron diferencias en la frecuencia (X2 = 3.22, gl = 1, P= 0.07 y niveles de infestación (t=0.18, P=0.86. No se detectó la presencia de A. woodi en las muestras analizadas. Los resultados demuestran un aumento en la frecuencia de N. apis en Yucatán.

  5. Effect of black clay soil moisture on the electrochemical behavior of API X70 pipeline steel

    Science.gov (United States)

    Hendi, R.; Saifi, H.; Belmokre, K.; Ouadah, M.; Smili, B.; Talhi, B.

    2018-03-01

    The effect of moisture content variation (20–100 wt.%) on the electrochemical behavior of API X70 pipeline steel buried in the soil of Skikda (East of Algeria) was studied using electrochemical techniques, scanning electron microscopy (SEM), X ray diffraction analysis (XRD) and weight loss measurement. The electrochemical measurements showed that the corrosion current Icorr is directly proportional to the moisture content up to 50 wt.%, beyond this content, this value becomes almost constant. The result were confirmed by electrochemical impedance spectroscopy; the capacitance of the double layer formed on the surface is the highest at 50 wt.%. A single time constant was detected by plotting the Bode diagrams. The steel surface degradation has been appreciated using the scanning electron microscopy observations. A few pitting corrosion at 20 wt.% moisture, followed by more degradation at 50 wt.% have been revealed. However, when the moisture amount exceeded 50 wt.%, the surface became entirely covered by a corrosion product. XRD analysis revealed the dominance of FeOOH and Fe3O4 phases on steel surface for a moisture content of 50 wt.%.

  6. X-ray crystal and molecular structure of (eta/sup 5/C/sub 5/H/sub 5/)UCl/sub 3/. 2PPh/sub 3/O thf: trichloro (eta/sup 5/cyclopentadienyl)bis(triphenylphosphine oxide) uranium(IV). thf

    Energy Technology Data Exchange (ETDEWEB)

    Bombieri, G; De Paoli, G [Consiglio Nazionale delle Ricerche, Padua (Italy). Lab. di Chimica e Tecnologia dei Radioelementi; Del Pra, A; Bagnall, K W

    1978-01-01

    Following reports of the preparation of (eta/sup 5/C/sub 5/H/sub 5/)UCl/sub 3/.xL (x = 1, L = dimethoxyethane and x = 2, L = tetrahydrofuran (thf), a series of analogous oxygen-donor complexes were isolated. This paper describes the crystal and molecular structure of one of them, ((eta/sup 5/C/sub 5/H/sub 5/)UCl/sub 3/.2PPh/sub 3/O)thf.

  7. Soldadura de recargue con aceros inoxidables dúplex

    OpenAIRE

    Zappa, Sebastián; Martínez, Juan; Svoboda, Hernán Gabriel; Surian, Estela

    2016-01-01

    Los aceros inoxidables dúplex se caracterizan por poseer una estructura dual constituida por ferrita y austenita en iguales proporciones. Poseen una combinación de buenas propiedades mecánicas y resistencia a la corrosión, que dependen de la composición química y de la relación entre las fases mencionadas. Son ampliamente utilizados en las industrias de procesos químicos y, fundamentalmente, del petróleo y gas. La soldadura de recargue, es utilizada en las industrias de fabricación y reparaci...

  8. Phase transition and piezoelectric properties of K0.48Na0.52NbO3-LiTa0.5Nb0.5O3-NaNbO3 lead-free ceramics

    International Nuclear Information System (INIS)

    Gao Feng; Liu Liangliang; Xu Bei; Cao Xiao; Deng Zhenqi; Tian Changsheng

    2011-01-01

    Highlights: → The evolution of the crystal structure for the new phase K 3 Li 2 Nb 5 O 15 was described. → The dielectric relaxor behavior would be strengthened by increasing plate-like NN. → k p and d 33 decrease with increasing amount of plate-like NN. → 0.01-0.03 mol of plate-like NN is a proper content for texturing ceramics by RTGG. - Abstract: Plate-like NaNbO 3 (NN) particles were used as the raw material to fabricate (1 - x)[0.93 K 0.48 Na 0.52 Nb O 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 ]-xNaNbO 3 lead-free piezoelectric ceramics using a conventional ceramic process. The effects of NN on the crystal structure and piezoelectric properties of the ceramics were investigated. The results of X-ray diffraction suggest that the perovskite phase coexists with the K 3 Li 2 Nb 5 O 15 phase, and the tilting of the oxygen octahedron is probably responsible for the evolution of the tungsten-bronze-typed K 3 Li 2 Nb 5 O 15 phase. The Curie temperature (T C ) is shifted to lower temperature with increasing NN content. (1 - x)[0.93 K 0.48 Na 0.52 NbO 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 ]-xNaNbO 3 ceramics show obvious dielectric relaxor characteristics for x > 0.03, and the relaxor behavior of ceramics is strengthened by increasing NN content. Both the electromechanical coupling factor (k p ) and the piezoelectric constant (d 33 ) decrease with increasing amounts of NN. 0.01-0.03 mol of plate-like NaNbO 3 in 0.93 K 0.48 Na 0.52 NbO 3 -0.07Li(Ta 0.5 Nb 0.5 )O 3 gives the optimum content for preparing textured ceramics by the RTGG method.

  9. Caracterización de aceros dual-phase obtenidos por laminación en caliente

    Directory of Open Access Journals (Sweden)

    Houbaert, Y.

    2011-02-01

    Full Text Available Samples were obtained from C-Mn-Si steel available in the market. Through a hot rolling and coiling process, it was possible to obtain Dual-Phase steel with microstructural and mechanical properties in the theoretical range typical of this material. The thermomechanical process consisted of a strong reduction by multiples pass of hot rolling at temperatures above Ar3, controlled-cooling the sheets during 5 s (at a rate of 20 °C/s in the equilibrium range α+γ. Temperature Ar3 measured by differential scanning calorimetry was 890 °C. Quenching was then carried out in the coiling temperatures range (500-675 °C, cooling the samples in accordance to an established curve that corresponds to the actual cooling curve of a coil. The microstructural characterization of the samples obtained was carried out by optical microscopy, scanning electron microscopy and atomic force microscopy. Additionally, texture measurements were carried out by X-ray diffraction in order to study the resulting orientations due to the finishing rolling temperature and coiling temperature, determining the influence on these parameters of the different texture components. The microstructural results were complemented with the normal and planar anisotropy indexes measured in according to the ASTM E-517 standard. The intensities of the different texture components were correlated with the values of anisotropy indexes, finding that it is possible to obtain only a slightly enhancement in the normal anisotropy index through an appropriate combination of finish rolling and coiling temperatures.

    Se tomaron muestras de acero al C-Mn-Si disponible en el mercado y mediante un proceso de laminación en caliente y bobinado, se obtuvo acero Dual Phase con microestructura y propiedades mecánicas dentro del rango teórico esperado de este material. El proceso termomecánico consistió en producir una fuerte reducción a temperaturas mayores a Ar3

  10. The 2s2p 4P0sub(5/2) - 2p24Psup(e)sub(5/2)-transition in O VI

    International Nuclear Information System (INIS)

    Sjoedin, R.; Pihl, J.; Hallin, R.; Lindskog, J.; Marelius, A.

    1976-03-01

    The Li-like doubly excited transitions 2s2p 4 P 0 sub(5/2) - 2p 2 4 Psup(e)sub(5/2) in O VI has been studied with the beam-foil technique. Oxygen ion beams with energies between 4.5 to 9 MeV were used. The wavelength of the transition was measured to 944.0+-0.5 A and the lifetime for the upper level 2p 2 4 Psup(e) was measured to be 0.51+-0.04 ns. (Auth.)

  11. Application of digital image processing to determine the causes of failures in SAE 1018 carbon steel; Aplicacion del procesamiento digital de imagenes para la determinacion de las causas que provocan fallas en el acero al carbono SAE 1018

    Energy Technology Data Exchange (ETDEWEB)

    Bolanos-Rodriguez, E [Escuela Superior de Tizayuca, Universidad Autonoma del Estado de Hidalgo, Tizayuca, Hidalgo (Mexico)]. E-mail: bola7112@yahoo.com.mx; Gonzalez-Islas, J.C. [Universidad Tecnologica de Tulancingo, Tulancingo, Hidalgo (Mexico)]. E-mail: juanc.gonzalez@utec-tgo.edu.mx; Felipe-Riveron, E.M. [Centro de Investigacion en Computacion, Instituto Politecnico Nacional, Mexico, D.F. (Mexico)]. E-mail: edgardo@cic.ipn.mx

    2013-03-15

    The research is focused on determining the causes of failures in the SAE 1018 carbon steel that is used in pipes carrying drinking water. Digital processing of images captured by photomicrographs by scanning electron microscopy coupled with the technique of X-ray microanalysis. The results demonstrate that the low quality of the raw materials and the manufacturing process of steel are the reasons for the occurrence of cracks observed in the material. [Spanish] La investigacion se centra en determinar las causas que provocan fallas en el acero al carbono SAE 1018 que es utilizado en tuberias que transportan agua potable. Se emplea el procesamiento digital de imagenes de las microfotografias captadas por medio de microscopia electronica de barrido, unido a la tecnica de microanalisis de rayos X. Los resultados obtenidos demuestran que la baja calidad de las materias primas y el proceso de manufactura del acero son las razones de la ocurrencia de fisuras observadas en el material.

  12. EFECTO DEL PRECALENTAMIENTO Y LA SEVERIDAD DE TEMPLE SOBRE LA RESISTENCIA AL DESGASTE ADHESIVO DEL ACERO AUSTENÍTICO AL MANGANESO

    Directory of Open Access Journals (Sweden)

    OSCAR FABIÁN HIGUERA COBOS

    2010-01-01

    Full Text Available En este trabajo de investigación se estudió el efecto del precalentamiento y la severidad de temple sobre la resistencia al desgaste adhesivo del acero austenítico al manganeso ASTM A 128 grado C. El material se sometió a ciclos térmicos de temple y revenido con y sin precalentamiento con el fin de evaluar su influencia sobre la resistencia al desgaste. Posteriormente el material fue sometido a prueba según norma ASTM G83 y se determinó que el acero Austenítico al manganeso, es un material que presenta una microestructura metaestable en condiciones estables y no debe ser sometido a tratamiento térmico de revenido a altas temperaturas debido que favorece la descomposición de esta a ferrita (fase blanda de los acero y por ende disminuye su resistencia al desgaste.

  13. The possibilities for reuse of steel scrap in order to obtain blades for knives; Posibilidades de reutilización de la chatarra de acero para la obtención de cuchillas para cortar

    Energy Technology Data Exchange (ETDEWEB)

    Štrbaca, N.; Markovića, I.; Mitovskia, A.; Balanovića, L.; Živkovića, D.; Grekulović, V.

    2017-09-01

    The purpose of this study is to determine fracture toughness of Resistance Spot Welded (RSW) Dual Phase (DP) steels. RSW of galvanized and ungalvanized DP 450 steel sheets was carried out on spot welding machine. Fracture toughness of RSW joints of galvanized and ungalvanized DP 450 steel sheets was calculated from tensile-shear tests. New empirical equations were developed using Least Squares Method (LSM) between energy release rate, fracture toughness and critical crack size depending on the relationship between hardness and fracture toughness values. Results indicated that fracture toughness of joints welded by using RSW increased exponentially while the hardness decreased. In addition, fracture toughness and energy release rate of RSW galvanized DP 450 steel sheets were lower compared to RSW ungalvanized DP 450 steel sheets which had approximately the same hardness. [Spanish] El trabajo presenta los resultados de la caracterización de diversos tipos de aceros que han llegado al final de su ciclo de vida útil, y de los que se desconocía su composición química, propiedades mecánicas y tratamiento termomecánico aplicado previamente. El estudio se realizó con el objetivo de analizar las posibilidades de reutilización de algunos de estos materiales en aplicaciones agrícolas e industriales, obteniendo hojas de corte. Las formas exigidas a las hojas de corte se consiguieron aplicando diversos tipos de tratamientos termomecánicos. El análisis químico de la chatarra de acero de acero se realizó utilizando Energías Dispersivas de Rayos X. La microestructura se estudió utilizando Microscopía Óptica y Microscopía Electrónica de Barrido. La dureza de la chatarra de acero y de las cuchillas obtenidas se midió utilizando la escala Rockwell C. Los valores de dureza de las cuchillas obtenidas indican una buena selección de los productos finales de acero.

  14. Cloning of araA Gene Encoding L-Arabinose Isomerase from Marine Geobacillus stearothermophilus Isolated from Tanjung Api, Poso, Indonesia

    Directory of Open Access Journals (Sweden)

    DEWI FITRIANI

    2010-06-01

    Full Text Available L-arabinose isomerase is an enzyme converting D-galactose to D-tagatose. D-tagatose is a potential sweetener-sucrose substitute which has low calorie. This research was to clone and sequence araA gene from marine bacterial strain Geobacillus stearothermophilus isolated from Tanjung Api Poso Indonesia. The amplified araA gene consisted of 1494 bp nucleotides encoding 497 amino acids. DNA alignment analysis showed that the gene had high homology with that of G. stearothermophilus T6. The enzyme had optimum activity at high temperature and alkalin condition.

  15. The putative serine protease inhibitor Api m 6 from Apis mellifera venom: recombinant and structural evaluation.

    Science.gov (United States)

    Michel, Y; McIntyre, M; Ginglinger, H; Ollert, M; Cifuentes, L; Blank, S; Spillner, E

    2012-01-01

    Immunoglobulin (Ig) E-mediated reactions to honeybee venom can cause severe anaphylaxis, sometimes with fatal consequences. Detailed knowledge of the allergic potential of all venom components is necessary to ensure proper diagnosis and treatment of allergy and to gain a better understanding of the allergological mechanisms of insect venoms. Our objective was to undertake an immunochemical and structural evaluation of the putative low-molecular-weight serine protease inhibitor Api m 6, a component of honeybee venom. We recombinantly produced Api m 6 as a soluble protein in Escherichia coli and in Spodoptera frugiperda (Sf9) insect cells.We also assessed specific IgE reactivity of venom-sensitized patients with 2 prokaryotically produced Api m 6 variants using enzyme-linked immunosorbent assay. Moreover, we built a structural model ofApi m 6 and compared it with other protease inhibitor structures to gain insights into the function of Api m 6. In a population of 31 honeybee venom-allergic patients, 26% showed specific IgE reactivity with prokaryotically produced Api m 6, showing it to be a minor but relevant allergen. Molecular modeling of Api m 6 revealed a typical fold of canonical protease inhibitors, supporting the putative function of this venom allergen. Although Api m 6 has a highly variant surface charge, its epitope distribution appears to be similar to that of related proteins. Api m 6 is a honeybee venom component with IgE-sensitizing potential in a fraction of venom-allergic patients. Recombinant Api m 6 can help elucidate individual component-resolved reactivity profiles and increase our understanding of immune responses to low-molecular-weight allergens

  16. Modelos de pérdida de masa de acero por corrosión atmosférica en Colombia usando inteligencia computacional

    Directory of Open Access Journals (Sweden)

    Esteban Velilla

    2009-01-01

    Full Text Available Con el fin de clasificar la corrosividad de las diferentes atmósferas colombianas, como parte de un proyecto de investigación extenso [1], se expusieron placas de acero al carbono en 21 estaciones distribuidas a lo largo de la infraestructura eléctrica del país (líneas de transmisión y subestaciones. En estas estaciones se midieron entre otros, el tiempo de humectación y la deposición de sulfatos y cloruros durante 12 meses; además, bimensualmente se tomaban placas de acero para medir en laboratorio la pérdida de masa sufrida por estas durante el tiempo de exposición. La clasificación de las 21 estaciones se hizo en 4 grupos, considerando: el tiempo de humectación, contenidos de cloruros y sulfatos, la altura sobre el nivel del mar y el tiempo de exposición de las placas; variables consideradas linealmente independientes según la técnica de descomposición en valores singulares (SVD realizada. El criterio utilizado para la clasificación fue el de similitud de las variables utilizando la norma Euclidiana considerada en la red neuronal no supervisada tipo Kohonen. Adicionalmente, se implementaron modelos para la pérdida de masa del acero para cada uno de los grupos usando redes neuronales (RN tipo Feed-Forward, definiéndose como entradas las variables antes mencionadas y como única salida la pérdida de masa. Complementariamente se presenta una comparación entre el modelo de RN para el grupo 1, con otros modelos obtenidos usando Algoritmos Genéticos (AG y el método Simplex.

  17. Optimización del acero usado como soporte y gancho de sujeción del acero de refuerzo en cimentaciones de concreto

    OpenAIRE

    Sánchez Trujillo, Bryan; Sánchez Trujillo, Bryan; Sánchez Trujillo, Bryan

    2015-01-01

    Para el proceso constructivo de cimentaciones de concreto se usan diversos accesorios, algunos estandarizados y otros no; uno de los no estandarizados es el acero usado como soporte y gancho de sujeción de las barras de refuerzo, (comúnmente llamado "burro", "burrito" o "silletas" de soporte), pues en los planos estructurales no se detalla la forma de colocar y sostener las barras de refuerzo y en obra las silletas se colocan de forma empírica según las experiencias previas de los encargados ...

  18. Survey of diseases and parasites of honeybees (Apis mellifera L.) in Sudan

    International Nuclear Information System (INIS)

    El-Niweiri, M. A.; El-Sarrag, M. S. A.; Satti, A. A.

    2009-01-01

    A survey of the honeybee diseases and parasites including questionnaires were carried out in eight bee areas in Sudan during the season 2002/03. About 117 local colonies and 324 packages of imported colonies of Apis mellifera were inspected, in addition to 25 colonies of Apis florea. All areas were found to be free of most bacterial brood diseases and fungal diseases, except the bacterial brood disease (Serratia marcescens) which was merely detected in 2.6% of Khartoum colonies. However, non infective dysentery was the only adult disease found during this study infecting 18.2% of Kordofan colonies. On the other hand, the parasitic mite (Varroa jacobsoni) was reported as first record in Sudan, detected only in Khartoum State infecting about 75% of colonies in apiaries and 27% of wild colonies. Sudanese honeybees were found to be characterized by hygienic behaviour of colonies which resist most pests and diseases, and no chemicals were used for control.(Author)

  19. Acero de alto silicio producido por inmersión en Al-Si y recocido de difusión

    Directory of Open Access Journals (Sweden)

    Ros-Yáñez, Tanya

    2000-10-01

    Full Text Available It is difficult to process steel sheet with a high Si content (>3.5%Si, mainly because of its brittleness and the appearance of cracks during rolling and oxidation. However, there is a market for this steel in electrical applications because of the favourable influence of Si on magnetostriction and electrical resistivity. As an alternative process, 3% Si-steel substrates were coated with hypereutectic Al-Si-alloys in a "hot-dip simulator" using different preheating and dipping times. The obtained layers were characterised by SEM and EDS analysis. Diffusion annealing experiments were performed to obtain sufficient amount of Si in the steel. It was observed that:

    • intermetallic phases appear in the coating layers as according to the ternary Fe-Si-Al diagram
    • with a double dipping primary silicon crystals are formed in the surface layer
    • the ordered DO3 structure is present if the dipping and/or diffusion time is long enough
    • homogeneous silicon gradients in the whole substrate thickness have not yet been achieved
    • theoretic calculations show that Si-gradient, also have beneficial effects on magnetic behaviour


    Es difícil procesar aceros eléctricos de alto contenido en silicio (>3,5 % Si. Esto se debe principalmente, a problemas de fragilidad, aparición de grietas durante la laminación y oxidación. Sin embargo, existe un importante mercado para este tipo de acero en aplicaciones eléctricas debido a la favorable influencia que ejerce el Si sobre la magnetoestricción, las pérdidas eléctricas y la resistividad eléctrica. Como proceso alternativo, se sumergieron substratos de acero con 3 % de silicio en una aleación hipereutéctica Al-25 % Si, en un simulador de recubrimiento por inmersión en caliente. En los ensayos se utilizaron diferentes tiempos de precalentamiento y de inmersión. En la segunda fase de la investigación se llevaron a cabo recocidos de difusión en el

  20. Integration of Experience API Into CDET’s E-Learning

    Science.gov (United States)

    2016-06-01

    50 x THIS PAGE INTENTIONALLY LEFT BLANK xi LIST OF TABLES Table 1. SaaS Pricing Strategies. Adapted from...Learning Record Store MCU Marine Corps University PIF Package Interchange File PME Professional Military Education SaaS Software as a Service...method consists of an e- learning course with xAPI and utilizes existing software as a service ( SaaS ) learning technologies to create a new way to use

  1. Data.gov CKAN API

    Data.gov (United States)

    General Services Administration — The data.gov catalog is powered by CKAN, a powerful open source data platform that includes a robust API. Please be aware that data.gov and the data.gov CKAN API...

  2. 48 CFR 52.204-5 - Women-Owned Business (Other Than Small Business).

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Women-Owned Business (Other Than Small Business). 52.204-5 Section 52.204-5 Federal Acquisition Regulations System FEDERAL... Provisions and Clauses 52.204-5 Women-Owned Business (Other Than Small Business). As prescribed in 4.607(b...

  3. SPT0346-52: NEGLIGIBLE AGN ACTIVITY IN A COMPACT, HYPER-STARBURST GALAXY AT z = 5.7

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Jingzhe; Gonzalez, Anthony H. [Department of Astronomy, University of Florida, Gainesville, FL 32611 (United States); Vieira, J. D.; Sreevani, J. [Department of Astronomy and Department of Physics, University of Illinois, 1002 West Green St., Urbana, IL 61801 (United States); Aravena, M. [Núcleo de Astronomía, Facultad de Ingeniería, Universidad Diego Portales, Av. Ejército 441, Santiago (Chile); Ashby, M. L. N. [Harvard-Smithsonian Center for Astrophysics, 60 Garden Street, Cambridge, MA 02138 (United States); Béthermin, M.; Breuck, C. de; Gullberg, B. [European Southern Observatory, Karl Schwarzschild Straße 2, D-85748 Garching (Germany); Bothwell, M. S. [Cavendish Laboratory, University of Cambridge, JJ Thompson Ave, Cambridge CB3 0HA (United Kingdom); Brandt, W. N. [Institute for Gravitation and the Cosmos, The Pennsylvania State University, University Park, PA 16802 (United States); Carlstrom, J. E. [Kavli Institute for Cosmological Physics, University of Chicago, 5640 South Ellis Avenue, Chicago, IL 60637 (United States); Chapman, S. C. [Dalhousie University, Halifax, Nova Scotia (Canada); Hezaveh, Y. [Kavli Institute for Particle Astrophysics and Cosmology, Stanford University, Stanford, CA 94305 (United States); Litke, K.; Marrone, D. P.; Spilker, J. S. [Steward Observatory, University of Arizona, 933 North Cherry Avenue, Tucson, AZ 85721 (United States); Malkan, M. [Department of Physics and Astronomy, University of California, Los Angeles, CA 90095-1547 (United States); McDonald, M. [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, 37-582C, Cambridge, MA 02139 (United States); Murphy, E. J., E-mail: jingzhema@ufl.edu [National Radio Astronomy Observatory, 520 Edgemont Road, Charlottesville, VA 22903 (United States); and others

    2016-12-01

    We present Chandra ACIS-S and Australia Telescope Compact Array (ATCA) radio continuum observations of the strongly lensed dusty, star-forming galaxy SPT-S J034640-5204.9 (hereafter SPT0346-52) at z = 5.656. This galaxy has also been observed with ALMA, HST , Spitzer , Herschel , Atacama Pathfinder EXperiment, and the Very Large Telescope. Previous observations indicate that if the infrared (IR) emission is driven by star formation, then the inferred lensing-corrected star formation rate (SFR) (∼4500 M {sub ☉} yr{sup −1}) and SFR surface density Σ{sub SFR} (∼2000 M {sub ☉} yr{sup −1} kpc{sup −2}) are both exceptionally high. It remained unclear from the previous data, however, whether a central active galactic nucleus (AGN) contributes appreciably to the IR luminosity. The Chandra upper limit shows that SPT0346-52 is consistent with being star formation dominated in the X-ray, and any AGN contribution to the IR emission is negligible. The ATCA radio continuum upper limits are also consistent with the FIR-to-radio correlation for star-forming galaxies with no indication of an additional AGN contribution. The observed prodigious intrinsic IR luminosity of (3.6 ± 0.3) × 10{sup 13} L {sub ☉} originates almost solely from vigorous star formation activity. With an intrinsic source size of 0.61 ± 0.03 kpc, SPT0346-52 is confirmed to have one of the highest Σ{sub SFR} of any known galaxy. This high Σ{sub SFR}, which approaches the Eddington limit for a radiation pressure supported starburst, may be explained by a combination of very high star formation efficiency and gas fraction.

  4. SPT0346-52: NEGLIGIBLE AGN ACTIVITY IN A COMPACT, HYPER-STARBURST GALAXY AT z = 5.7

    International Nuclear Information System (INIS)

    Ma, Jingzhe; Gonzalez, Anthony H.; Vieira, J. D.; Sreevani, J.; Aravena, M.; Ashby, M. L. N.; Béthermin, M.; Breuck, C. de; Gullberg, B.; Bothwell, M. S.; Brandt, W. N.; Carlstrom, J. E.; Chapman, S. C.; Hezaveh, Y.; Litke, K.; Marrone, D. P.; Spilker, J. S.; Malkan, M.; McDonald, M.; Murphy, E. J.

    2016-01-01

    We present Chandra ACIS-S and Australia Telescope Compact Array (ATCA) radio continuum observations of the strongly lensed dusty, star-forming galaxy SPT-S J034640-5204.9 (hereafter SPT0346-52) at z = 5.656. This galaxy has also been observed with ALMA, HST , Spitzer , Herschel , Atacama Pathfinder EXperiment, and the Very Large Telescope. Previous observations indicate that if the infrared (IR) emission is driven by star formation, then the inferred lensing-corrected star formation rate (SFR) (∼4500 M ☉ yr −1 ) and SFR surface density Σ SFR (∼2000 M ☉ yr −1 kpc −2 ) are both exceptionally high. It remained unclear from the previous data, however, whether a central active galactic nucleus (AGN) contributes appreciably to the IR luminosity. The Chandra upper limit shows that SPT0346-52 is consistent with being star formation dominated in the X-ray, and any AGN contribution to the IR emission is negligible. The ATCA radio continuum upper limits are also consistent with the FIR-to-radio correlation for star-forming galaxies with no indication of an additional AGN contribution. The observed prodigious intrinsic IR luminosity of (3.6 ± 0.3) × 10 13 L ☉ originates almost solely from vigorous star formation activity. With an intrinsic source size of 0.61 ± 0.03 kpc, SPT0346-52 is confirmed to have one of the highest Σ SFR of any known galaxy. This high Σ SFR , which approaches the Eddington limit for a radiation pressure supported starburst, may be explained by a combination of very high star formation efficiency and gas fraction.

  5. Comparative virulence and competition between Nosema apis and Nosema ceranae in honey bees (Apis mellifera).

    Science.gov (United States)

    Milbrath, Meghan O; van Tran, Toan; Huang, Wei-Fong; Solter, Leellen F; Tarpy, David R; Lawrence, Frank; Huang, Zachary Y

    2015-02-01

    Honey bees (Apis mellifera) are infected by two species of microsporidia: Nosema apis and Nosemaceranae. Epidemiological evidence indicates that N. ceranae may be replacing N. apis globally in A. mellifera populations, suggesting a potential competitive advantage of N. ceranae. Mixed infections of the two species occur, and little is known about the interactions among the host and the two pathogens that have allowed N. ceranae to become dominant in most geographical areas. We demonstrated that mixed Nosema species infections negatively affected honey bee survival (median survival=15-17days) more than single species infections (median survival=21days and 20days for N. apis and N. ceranae, respectively), with median survival of control bees of 27days. We found similar rates of infection (percentage of bees with active infections after inoculation) for both species in mixed infections, with N. apis having a slightly higher rate (91% compared to 86% for N. ceranae). We observed slightly higher spore counts in bees infected with N. ceranae than in bees infected with N. apis in single microsporidia infections, especially at the midpoint of infection (day 10). Bees with mixed infections of both species had higher spore counts than bees with single infections, but spore counts in mixed infections were highly variable. We did not see a competitive advantage for N. ceranae in mixed infections; N. apis spore counts were either higher or counts were similar for both species and more N. apis spores were produced in 62% of bees inoculated with equal dosages of the two microsporidian species. N. ceranae does not, therefore, appear to have a strong within-host advantage for either infectivity or spore growth, suggesting that direct competition in these worker bee mid-guts is not responsible for its apparent replacement of N. apis. Copyright © 2014 Elsevier Inc. All rights reserved.

  6. “MEDICION DE PARAMETROS GENERADORES DE ESFUERZOS RESIDUALES DURANTE EL PROCESO DE SOLDADURA DE ACERO INOXIDABLE AUSTENITICO AISI 304L”.

    OpenAIRE

    García López, Christian Jesus

    2012-01-01

    En la actualidad los procesos de soldadura por arco eléctrico se han convertido en la técnica por excelencia para la unión del acero y sus aleaciones. Se puede mencionar que la importancia de la soldadura, es tal, que sin ella no serían posibles muchos de los productos y servicios que cotidianamente son consumidos o requeridos por las sociedades contemporáneas actuales. Cada vez con mayor longitud y diámetro se instalan líneas de tubería para la distribución y conducción de tod...

  7. Ação tóxica de Manihot glaziovii Muell. Arg. sobre Apis mellifera L.

    Directory of Open Access Journals (Sweden)

    Francivaldo Marcio Pereira

    2014-06-01

    Full Text Available As Apis mellifera, são polinizadores de diversas espécies de vegetais, contribuindo com eficiência na reprodução de várias culturas de interesse econômico, sendo a florada necessária para sua sobrevivência, porem certas plantas podem conter substâncias tóxicas para esses indivíduos. Nesse sentido o objetivo foi avaliar o possível efeito tóxico de flores de Manihot glaziowii para abelhas Apis mellifera. O experimento foi conduzido no Laboratório de Abelhas e Nutrição Animal da Universidade Federal de Campina Grande em Pombal-PB. As flores de M. glaziovii foram coletadas no sitio Bom Jesus localizado no Município de Pombal-PB transportadas para o laboratório e postas para secar em estufa a 40 °C durante 48 horas, trituradas e peneiradas, pesado em três concentrações distintas (0,25%, 0,50% e 1,0% com relação ao peso do cândi. O macerado das flores foi misturado ao cândi e colocadas em recipientes de plásticos de 10 ml.  As abelhas foram selecionadas no favo de cria, recém-emergidas, pelo tamanho e coloração mais clara, e conduzidas para o laboratório.  Distribuídas em conjunto de 20 insetos em caixa de madeira, medindo 11 cm de comprimento X 11 de largura e 7 cm de altura e orifícios nas laterais. Em cada caixa foram colocados dois recipientes de plástico de 10 mL com a dieta contaminada e um chumaço de algodão embebido com água. Acondicionadas em câmara tipo B.O.D. com temperatura a 32º C e umidade relativa de 70 %. O experimento foi realizado no delineamento inteiramente casualisado, composto por três tratamentos (0,25%, 0,50% e 1,0% e uma testemunha, com três repetições. A contagem de operárias mortas ocorreu vinte e quatro horas após aplicação dos tratamentos. Os dados foram passados para o programa PRISMA 3.0, para análises dos dados utilizou-se o teste não-paramétrico Log Rank Test, na comparação das curvas de sobrevivência. O macerado das flores de M. glaziovii apresentaram toxicidade

  8. Identification of Staphylococcus species with the API STAPH-IDENT system.

    Science.gov (United States)

    Kloos, W E; Wolfshohl, J F

    1982-01-01

    The API STAPH-IDENT system was compared with conventional methods for the identification of 14 Staphylococcus species. Conventional methods included the Kloos and Schleifer simplified scheme and DNA-DNA hybridization. The API STAPH-IDENT strip utilizes a battery of 10 miniaturized biochemical tests, including alkaline phosphatase, urease, beta-glucosidase, beta-glucuronidase, and beta-galactosidase activity, aerobic acid formation from D-(+)-mannose, D-mannitol, D-(+)-trehalose, and salicin, and utilization of arginine. Reactions of cultures were determined after 5 h of incubation at 35 degrees C. Results indicated a high degree of congruence (greater than 90%) between the expedient API system and conventional methods for most species. The addition of a test for novobiocin susceptibility to the API system increased the accuracy of identification of S. saprophyticus, S. cohnii, and S. hominis, significantly. Several strains of S. hominis, S. haemolyticus, and S. warneri which were difficult to separate with the Kloos and Schleifer simplified scheme were accurately resolved by the API system. PMID:6752190

  9. Measurement of relative L X-ray intensity ratio following radioactive decay and photoionization

    Energy Technology Data Exchange (ETDEWEB)

    Yalcin, P. [Department of Science Education, Faculty of Education, Erzincan University, 24030 Erzincan (Turkey)], E-mail: pasayalcin@hotmail.com; Porikli, S.; Kurucu, Y.; Sahin, Y. [Department of Physics, Faculty of Sciences, Atatuerk University, 25240 Erzurum (Turkey)

    2008-05-22

    The measurements of the L X-ray intensity ratio I(L{alpha})/I(L{beta}), I(L{alpha})/I(L{gamma}), I(L{alpha})/I(L{iota}), I(L{beta})/I(L{gamma}) and I(L{iota})/I(L{gamma}) for elements Dy, Ho, Yb, W, Hg, Tl and Pb were experimentally determined both by photon excitation, in which 59.5 keV {gamma}-rays from a filtered radioisotope {sup 241}Am was used, and by the radioactive decay of {sup 160}Tb, {sup 160}Er, {sup 173}Lu, {sup 182}Re, {sup 201}Tl, {sup 203}Pb and {sup 207}Bi. L X-rays emitted by samples were counted by a Si(Li) detector with resolution 160 eV at 5.9 keV. Obtained values were compared with the calculated theoretical values. Theoretical values of the I(L{alpha}/L{beta}), I(L{alpha}/L{gamma}), I(L{alpha}/L{iota}), I(L{beta}/L{gamma}) and I(L{iota}/L{gamma}) intensity ratios were calculated using theoretically tabulated values of subshell photoionization cross-section, fluorescence yield, fractional X-ray emission rates, Coster-Kronig transition probabilities. It was observed that present values agree with previous theoretical and other available experimental results.

  10. Spin-polarized ground state and exact quantization at ν=5/2

    Science.gov (United States)

    Pan, Wei

    2002-03-01

    The nature of the even-denominator fractional quantum Hall effect at ν=5/2 remains elusive, in particular, its ground state spin-polarization. An earlier, so-called "hollow core" model arrived at a spin-unpolarized wave function. The more recent calculations based on a model of BCS-like pairing of composite fermions, however, suggest that its ground state is spin-polarized. In this talk, I will first review the earlier experiments and then present our recent experimental results showing evidence for a spin-polarized state at ν=5/2. Our ultra-low temperature experiments on a high quality sample established the fully developed FQHE state at ν=5/2 as well as at ν=7/3 and 8/3, manifested by a vanishing R_xx and exact quantization of the Hall plateau. The tilted field experiments showed that the added in-plane magnetic fields not only destroyed the FQHE at ν=5/2, as seen before, but also induced an electrical anisotropy, which is now interpreted as a phase transition from a paired, spin-polarized ν=5/2 state to a stripe phase, not unlike the ones at ν=9/2, 11/2, etc in the N > 1 higher Landau levels. Furthermore, in the experiments on the heterojunction insulated-gate field-effect transistors (HIGFET) at dilution refrigerator temperatures, a strong R_xx minimum and a concomitant developing Hall plateau were observed at ν=5/2 in a magnetic field as high as 12.6 Tesla. This and the subsequent density dependent studies of its energy gap largely rule out a spin-singlet state and point quite convincingly towards a spin-polarized ground state at ν=5/2.

  11. Flora de importância polinífera para Apis mellifera (L. na região de Viçosa, MG

    Directory of Open Access Journals (Sweden)

    Anna Frida Hatsue Modro

    2011-10-01

    Full Text Available Procurou-se conhecer a flora de importância polinífera para Apis mellifera (L. na região de Viçosa, MG, em período de entressafra de mel, entre agosto e dezembro de 2005. O experimento foi realizado em dois apiários distintos, cada um com cinco colmeias. As cargas retidas nos coletores de pólen instalados nas colmeias foram analisadas quanto à origem botânica. As plantas em floração no entorno dos apiários foram coletadas e identificadas. A maioria das plantas de importância polinífera para abelhas na região de Viçosa era nativa, localizada em jardins e com hábito arbóreo. Pela análise palinológica, verificou-se que espécies como Anadenanthera colubrina, Arecaceae sp., Baccharis dracunculifolia, B. melastomaefolia, Coffea spp., Emilia sagittata, Eugenia uniflora, Mikania cordifolia, M. hirsutissima, Myrcia fallax, Psidium guajava, Vernonia condensata, V. diffusa, V. lanuginosa e V. mariana são potenciais recursos poliníferos a serem utilizados no período de entressafra do mel. Os resultados indicaram a importância de plantas localizadas em áreas abertas para o forrageamento de pólen por A. mellifera e confirmaram o potencial polinífero da região estudada, durante o período de entressafra do mel.

  12. Preparation of CuIn{sub 1-x}Ga{sub x}S{sub 2} (x = 0.5) flowers consisting of nanoflakes via a solvothermal method

    Energy Technology Data Exchange (ETDEWEB)

    Liang Xiaojuan [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang Province 325035 (China); Institute of Materials and Technology, Dalian Maritime University, Dalian 116026 (China); Zhong Jiasong; Yang Fan; Hua Wei; Jin Huaidong [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang Province 325035 (China); Liu Haitao, E-mail: lht@wzu.edu.cn [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang Province 325035 (China); Sun Juncai [Institute of Materials and Technology, Dalian Maritime University, Dalian 116026 (China); Xiang Weidong, E-mail: weidongxiang@yahoo.com.cn [College of Chemistry and Materials Engineering, Wenzhou University, Wenzhou, Zhejiang Province 325035 (China)

    2011-05-26

    Highlights: > We report for the first time a small biomolecule-assisted route using L-cysteine as sulfur source and complexing agent to synthesis CuIn{sub 0.5}Ga{sub 0.5}S{sub 2} crystals. > The possible mechanisms leading to CuIn{sub 0.5}Ga{sub 0.5}S{sub 2} flowers consisting of nanoflakes were proposed. > In addition, the morphology, structure, and phase composition of the as-prepared CuIn{sub 0.5}Ga{sub 0.5}S{sub 2} products were investigated in detail by XRD, FESEM, EDS, XPS, TEM (HRTEM) and SAED. - Abstract: CuIn{sub 1-x}Ga{sub x}S{sub 2} (x = 0.5) flowers consisting of nanoflakes were successfully prepared by a biomolecule-assisted solvothermal route at 220 deg. C for 10 h, employing copper chloride, gallium chloride, indium chloride and L-cysteine as precursors. The biomolecule L-cysteine acting as sulfur source was found to play a very important role in the formation of the final product. The diameter of the CuIn{sub 0.5}Ga{sub 0.5}S{sub 2} flowers was 1-2 {mu}m, and the thickness of the flakes was about 15 nm. The obtained products were characterized by X-ray diffraction (XRD), energy dispersion spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction spectroscopy (SAED), and UV-vis absorption spectroscopy. The influences of the reaction temperature, reaction time, sulfur source and the molar ratio of Cu-to-L-cysteine (reactants) on the formation of the target compound were investigated. The formation mechanism of the CuIn{sub 0.5}Ga{sub 0.5}S{sub 2} flowers consisting of flakes was discussed.

  13. Consideraciones teórico prácticas acerca de la soldadura de los aceros al carbono

    Directory of Open Access Journals (Sweden)

    Osmundo Héctor Rodríguez Pérez

    2006-01-01

    Full Text Available Se analizan los tres tipos de aceros al carbono y su clasificación desde el punto de vista de su soldabilidad. Se pueden observar los aspectos físico - químicos en la zona fundida, zona de transición y zona afectada por el calor. Existen varios aspectos en la tecnología de la soldadura de los aceros al carbono, tales como: preparación de los bordes, limpieza superficial, posición relativa de las piezas, precalentamiento, selección del material de aporte, deposición de los cordones, postcalentamiento, tratamiento térmico posterior y el control de la calidad de las uniones soldadas a tomar en cuenta para realizar la soldadura.

  14. Study of the flight range and ideal density of the africanized honeybees, Apis mellifera L., 1758 (Hymenoptera: Apidae) labelled with 32 P on an apple orchard

    International Nuclear Information System (INIS)

    Paranhoa, B.A.J.

    1990-06-01

    The ideal density, the flight range, the choice for any flight direction, the influence of temperature and relative humidity of air about the honeybee's activity, Apis mellifera L.. 1758 (Hymenoptera: Apidae) were studied in an apple orchard, utilizing nuclear techniques. Five hives, with 35,000 bees each, were labelled with syrup (50%) content (2,5 μCi 32 P/ml) and taken one by one, every two days to the blossomed orchard. A circumference area of 100 m diameter (0,8 ha) W staked each 10 m from the center to the limit (50 m), making a cross, pointing out to North, South, East and West. The honeybees were collected on apple flowers, during 5 minutes in each stake, at 10:00 a.m. and 12:30 p.m. (author)

  15. Predominant Api m 10 sensitization as risk factor for treatment failure in honey bee venom immunotherapy

    DEFF Research Database (Denmark)

    Frick, Marcel; Fischer, Jörg; Helbing, Arthur

    2016-01-01

    BACKGROUND: Component resolution recently identified distinct sensitization profiles in honey bee venom (HBV) allergy, some of which were dominated by specific IgE to Api m 3 and/or Api m 10, which have been reported to be underrepresented in therapeutic HBV preparations. OBJECTIVE: We performed...... responders and nonresponders regarding levels of IgE sensitization to Api m 1, Api m 2, Api m 3, and Api m 5. In contrast, Api m 10 specific IgE was moderately but significantly increased in nonresponders. Predominant Api m 10 sensitization (>50% of specific IgE to HBV) was the best discriminator...... (specificity, 95%; sensitivity, 25%) with an odds ratio of 8.444 (2.127-33.53; P = .0013) for treatment failure. Some but not all therapeutic HBV preparations displayed a lack of Api m 10, whereas Api m 1 and Api m 3 immunoreactivity was comparable to that of crude HBV. In line with this, significant Api m 10...

  16. IgE-Api m 4 Is Useful for Identifying a Particular Phenotype of Bee Venom Allergy.

    Science.gov (United States)

    Ruiz, B; Serrano, P; Moreno, C

    Different clinical behaviors have been identified in patients allergic to bee venom. Compound-resolved diagnosis could be an appropriate tool for investigating these differences. The aims of this study were to analyze whether specific IgE to Api m 4 (sIgE-Api m 4) can identify a particular kind of bee venom allergy and to describe response to bee venom immunotherapy (bVIT). Prospective study of 31 patients allergic to bee venom who were assigned to phenotype group A (sIgE-Api m 4 Api m 4 ≥0.98 kU/L), treated with purified aqueous (PA) extract. Sex, age, cardiovascular risk, severity of preceding sting reaction, exposure to beekeeping, and immunological data (intradermal test, sIgE/sIgG4-Apis-nApi m 1, and sIgE-rApi m 2-Api m 4 were analyzed. Systemic reactions (SRs) during bVIT build-up were analyzed. Immunological and sting challenge outcomes were evaluated in each group after 1 and 2 years of bVIT. Phenotype B patients had more severe reactions (P=.049) and higher skin sensitivity (P=.011), baseline sIgE-Apis (P=.0004), sIgE-nApi m 1 (P=.0004), and sIgG4-Apis (P=.027) than phenotype A patients. Furthermore, 41% of patients in group B experienced SRs during the build-up phase with NA; the sting challenge success rate in this group was 82%. There were no significant reductions in serial intradermal test results, but an intense reduction in sIgE-nApi m 1 (P=.013) and sIgE-Api m 4 (P=.004) was observed after the first year of bVIT. Use of IgE-Api m 4 as the only discrimination criterion demonstrated differences in bee venom allergy. Further investigation with larger populations is necessary.

  17. Uncovering the immune responses of Apis mellifera ligustica larval gut to Ascosphaera apis infection utilizing transcriptome sequencing.

    Science.gov (United States)

    Chen, Dafu; Guo, Rui; Xu, Xijian; Xiong, Cuiling; Liang, Qin; Zheng, Yanzhen; Luo, Qun; Zhang, Zhaonan; Huang, Zhijian; Kumar, Dhiraj; Xi, Weijun; Zou, Xuan; Liu, Min

    2017-07-20

    Honeybees are susceptible to a variety of diseases, including chalkbrood, which is capable of causing huge losses of both the number of bees and colony productivity. This research is designed to characterize the transcriptome profiles of Ascosphaera apis-treated and un-treated larval guts of Apis mellifera ligustica in an attempt to unravel the molecular mechanism underlying the immune responses of western honeybee larval guts to mycosis. In this study, 24, 296 and 2157 genes were observed to be differentially expressed in A. apis-treated Apis mellifera (4-, 5- and 6-day-old) compared with un-treated larval guts. Moreover, the expression patterns of differentially expressed genes (DEGs) were examined via trend analysis, and subsequently, gene ontology analysis and KEGG pathway enrichment analysis were conducted for DEGs involved in up- and down-regulated profiles. Immunity-related pathways were selected for further analysis, and our results demonstrated that a total of 13 and 50 DEGs were annotated in the humoral immune-related and cellular immune-related pathways, respectively. Additionally, we observed that many DEGs up-regulated in treated guts were part of cellular immune pathways, such as the lysosome, ubiquitin mediated proteolysis, and insect hormone biosynthesis pathways and were induced by A. apis invasion. However, more down-regulated DEGs were restrained. Surprisingly, a majority of DEGs within the Toll-like receptor signaling pathway, and the MAPK signaling pathway were up-regulated in treated guts, while all but two genes involved in the NF-κB signaling pathway were down-regulated, which suggested that most genes involved in humoral immune-related pathways were activated in response to the invasive fungal pathogen. This study's findings provide valuable information regarding the investigation of the molecular mechanism of immunity defenses of A. m. ligustica larval guts to infection with A. apis. Furthermore, these studies lay the groundwork for

  18. Radioactive study of Mo{sup 93} and Mo{sup 95} levels and research of subshell effects for the shell 2d 5/2; Etude, par radioactivite des niveaux de {sup 93}Mo et de {sup 95}Mo et essai de mise en evidence de la sous-couche 2d{sub 5/2}

    Energy Technology Data Exchange (ETDEWEB)

    Levi Lesueur, Ch [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1961-03-15

    We studied the decay schemes of Tc{sup 93} et Tc{sup 95} to determine the spins of Mo{sup 93} and M{sup 95} levels, and especially the position of the single-particle level 1g 7/2. We found a large spacing between the neutron shells 2d 5/2 and 1g 7/2 like that observed first in Mo{sup 97}. As the subshell 2d 5/2 is so far from its neighbours, we thought that subshell effects could perhaps be discovered in the systematics of separation energies and beta-decay energies. We found such effects. (author) [French] Par l'etude des schemas de desintegration de {sup 93}Tc et {sup 95}Tc, nous avons essaye de determiner les spins des niveaux de {sup 93}Mo et {sup 95}Mo et en particulier la position du niveau de particule 1g 7/2. Nous avons ainsi confirme l'ecart important entre les couches de neutrons 2d 5/2 et 1g 7/2 deja constate a propos de {sup 97}Mo. Nous avons pense que la sous-couche 2d 5/2 ainsi isolee des couches voisines pouvait, peut etre, etre mise en evidence par l'etude des systematiques d'energies de separation et d'energies de desintegration beta. Nous avons verifie qu'il en etait bien ainsi. (auteur)

  19. BWR spent fuel transport and storage system for KKL: TN trademark 52L, TN trademark 97L, TN trademark 24 BHL

    International Nuclear Information System (INIS)

    Sicard, D.; Verdier, A.; Monsigny, P.A.

    2004-01-01

    The LEIBSTADT (KKL) nuclear power plant in Switzerland has opted to ship spent fuel to a central facility called ZWILAG for interim storage. In the mid-nineties, COGEMA LOGISTICS was contracted by KKL for the supply of the TN trademark a52L and TN trademark 97L transport and storage casks for BWR fuel types. In 2003, KKL also ordered from COGEMA LOGISTICS the supply of six TNae24 BHL transport and storage casks. This paper shows how all the three cask designs have responded to the KKL needs to ship and store BWR spent fuel. In addition, it highlights the already significant operational feedback of the TN trademark 52L and TN trademark 97L casks by the KKL and ZWILAG operators

  20. Determinación de tensiones por rayos x del acero AISI 1045 deformado por rodillo // Determination of stress for x‐ray of the steel AISI 1045 deformed for roller

    Directory of Open Access Journals (Sweden)

    Tomás Fernández‐Columbié

    2012-01-01

    Full Text Available El objetivo del trabajo es realizar el análisis de las tensiones a muestras de acero AISI 1045 endurecidasen frío por rodillo. Con empleo del método de Willianson–Hall se determinó las macro ymicrodeformaciones; la deformación reticular del parámetro de red; el tamaño de las cristalitas; losesfuerzos en la red cristalina y la reducción del tamaño promedio de los granos, lo que permitió establecerlos mecanismos de endurecimiento del acero AISI 1045, deformado por rodadura. Fueron medidos yanalizados diferentes puntos teniendo en cuenta los índices de Miller para la fase ferrítica del acero. Losmodelos lineales obtenidos, son estadísticamente significativos, que muestran una tendencia creciente delas propiedades mecánicas y metalúrgicas, según se incrementan las variables independientes delproceso de experimentación.Palabras claves: rodillo, rodadura, deformación plástica.__________________________________________________________________AbstractThe objective of the paper is to carry out the analysis from the tensions to steel samples AISI 1045hardened cold for roller. With employment of the method of Willianson-Hall was determined the macro andmicro deformations; the reticular deformation of the net parameter; the size of the crystallites; the efforts inthe crystalline net and the reduction of the size average of the grains, what allowed to establish themechanisms of hardening of the steel AISI 1045, deformed by rolling. They were measured and analyzeddifferent points keeping in mind the indexes of Miller for the phase ferrite of the steel. The obtained linealmodels, they are statistically significant that they show a growing tendency of the mechanical estates andmetallurgical, as the independent variables of the experimentation process are increased.Key words: roller, rolling, plastic deformation.

  1. Resultados de ensayos de soldadura a tope y por solape, con electrodo, de barras de aceros estirados en frío

    Directory of Open Access Journals (Sweden)

    Calavera Ruiz, José

    1969-03-01

    Full Text Available The authors report on a series of tests carried out in the welding of reinforced concrete bars. The tested bars were cold drawn, with elastic limits of 4,200 and 5,000 kg/cm2. The tests included butt and overlap welding, involving excentric and axial overlaps, with joint reinforcements. Results of these experiments show that if the indicated method is adopted, including an average standard of workmanship, the weld attains 100 % of the bar strength.Los autores dan cuenta de una serie de ensayos realizados sobre soldadura de barras para hormigón armado. Las barras ensayadas son de acero estirado en frío con límites elásticos de 4.200 y 5.000 kp/cm2. Los ensayos abarcaron la soldadura a tope y la soldadura por solape, con sus variantes de solape excéntrico y solape centrado con cubrejuntas. Los resultados de los ensayos demuestran que siguiendo la técnica indicada, y con una calidad normal de ejecución, la soldadura presenta el 100 % de la resistencia de la barra.

  2. Comportamiento al desgaste por deslizamiento en aceros inoxidables: ferrítico, austenítico, dúplex y martensítico.

    OpenAIRE

    Renedo Rouco, Jordi

    2010-01-01

    En este proyecto se estudia el comportamiento al desgaste por deslizamiento de cuatro aceros representativos de las cuatro grandes familias de aceros inoxidables: ferrítico (AISI 446), austenítico (AISI 316), dúplex (AISI 2205) y martensítico (AISI 420). Para cada uno de ellos se han realizado: caracterización metalográfica, determinación de dureza, densidad y rugosidad, y ensayos de tribología mediante la técnica de bola sobre disco. Esta técnica consiste en deslizar una bola ...

  3. Efecto de la Composición Química del Metal de Aporte y del Calor Aportado Sobre la Microestructura y las Propiedades Mecánicas de Juntas Soldadas de Aceros Inoxidables Dúplex

    Directory of Open Access Journals (Sweden)

    Sebastián Zappa

    Full Text Available Resumen Los aceros inoxidables dúplex poseen una microestructura dual (ferrita y austenita con contenidos aproximadamente iguales y se caracterizan por tener buena soldabilidad, buenas propiedades mecánicas y una alta resistencia a la corrosión generalizada y localizada. Gracias a estas características, estos aceros son los principales materiales a emplear en cañerías con altas exigencias, ampliamente utilizados en varias industrias, principalmente la petroquímica. Dichas propiedades están controladas por la composición química, el equilibrio microestructural y la ausencia de compuestos intermetálicos. El objetivo de este trabajo fue estudiar la influencia de la composición química del metal de aporte y el calor aportado sobre la microestructura y las propiedades mecánicas en juntas soldadas de cañerías de acero inoxidable dúplex. El metal base utilizado fue un acero inoxidable dúplex UNS S31803 de 8” de diámetro y 8,18 mm de espesor y los metales de aporte fueron dos alambres tubulares que depositan aceros inoxidables dúplex y lean dúplex (AWS A5.22: E2209T1-1 y E2209T1-G, mediante el proceso de soldadura semi-automático bajo protección gaseosa, soldados con alto y bajo calor aportado. De cada probeta se extrajeron muestras donde se determinó la composición química, se realizó la caracterización microestructural y se determinaron las propiedades mecánicas (dureza, tracción y Charpy-V.

  4. Ethanol self-administration in free-flying honeybees (Apis mellifera L.) in an operant conditioning protocol.

    Science.gov (United States)

    Sokolowski, Michel B C; Abramson, Charles I; Craig, David Philip Arthur

    2012-09-01

    This study examines the effect of ethanol (EtOH) on continuous reinforcement schedules in the free-flying honeybee (Apis mellifera L.). As fermented nectars may be encountered naturally in the environment, we designed an experiment combining the tools of laboratory research with minimal disturbance to the natural life of honeybees. Twenty-five honeybees were trained to fly from their colonies to a fully automated operant chamber with head poking as the operant response. Load size, intervisit interval, and interresponse times (IRTs) served as the dependent variables and were monitored over the course of a daily training session consisting of many visits. Experimental bees were tested using an ABA design in which sucrose only was administered during condition A and a 5% EtOH sucrose solution was administered during condition B. Control bees received sucrose solution only. Most bees continued to forage after EtOH introduction. EtOH significantly reduced the load size and the intervisit interval with no significant effect on IRTs. However, a look on individual data shows large individual differences suggesting the existence of different kinds of behavioral phenotypes linked to EtOH consumption and effects. Our results contribute to the study of EtOH consumption as a normal phenomenon in an ecological context and open the door to schedule-controlled drug self-administration studies in honeybees. Copyright © 2012 by the Research Society on Alcoholism.

  5. Improving honey production in worker bees (Apis mellifera adansoni ...

    African Journals Online (AJOL)

    Modification of feeding activity, nursing care and undertaker behaviour were carried out among some colonies of honey bees Apis mellifera adansoni L to know the effect on honey production. Apiaries Numbers 1, 2 and 3 contain three replicates of experimental hives while apiary Number 4 contains control hives. All the ...

  6. Resistencia a la oxidación de aleaciones Ni-Cr-Al plaqueadas por láser sobre aceros al carbono e inoxidables austeníticos

    Directory of Open Access Journals (Sweden)

    de Damborenea, J.

    1995-04-01

    Full Text Available Laser surface cladding has been carried out by means of a 5 kW CO2 continuous wave laser on both a mild and a stainless steel. A powder injection technique has been used to deliver a Ni-Cr-Al alloy onto the steel molten pool. After processing, samples were analyzed by optical and scanning electron microscopy in order to know the microstructure and composition of present phases. High temperature corrosion resistance tests were done in an oxidant environment at temperatures of 950 °C. Phase transformations and corrosion behaviour are discussed. A general conclusion is the suitability of these alloys to bear oxidation due to the formation of protective oxide layers on their surface.

    Se realiza un estudio sobre la obtención de recubrimientos de superficie mediante un láser continuo de CO2 de 5 kW de potencia de salida. Mediante la técnica de inyección de partículas, se realizaron plaqueados en superficie de Ni-Cr-Al sobre un acero suave y otro inoxidable de tipo 316. Tras el procesado, se estudió la microestructura de las probetas obtenidas. Posteriormente, se procedió a su ensayo en atmósfera oxidante a 950 °C, observándose la evolución de la microestructura, la formación de las capas de óxido y la cinética del proceso. Como conclusión general, destaca, independientemente de la base sobre la que se obtienen los recubrimientos, la gran resistencia del material a la oxidación, seguramente debida a la formación de capas de alúmina que actúan como barreras frente al ataque del oxidante.

  7. HEURISTIC EVALUATION FOR MOBILE APPLICATION (STUDI KASUS: APLIKASI DEPO AUTO 2000 TANJUNG API API PALEMBANG

    Directory of Open Access Journals (Sweden)

    Usman Ependi

    2017-11-01

    Full Text Available Heuristic evaluation merupakan salah satu bentuk usability testing perangkat lunak yang dinilai oleh pengguna (evaluator. Dalam melakukan heuristic evaluation instrumen penilaian terdiri dari sepuluh (10 pernyataan dengan lima pilihan jawaban dalam skala severity ratings. Dalam penelitian ini heuristic evaluation terhadap aplikasi Depo Auto 2000 Tanjung Api-Api Palembang yang dilakukan oleh 4 evaluator.  Hasil dari heuristic evaluation dikelompokkan kedalam  masing-masing instrumen yaitu visibility of system status dengan nilai 0,75, match between system and the real world dengan nilai 0,25, user control and freedom dengan nilai 0,25, consistency and standards dengan nilai 0,75, error prevention dengan nilai 1, recognition rather than recall dengan nilai 1,25, flexibility and efficiency of use dengan nilai 0,25, Aesthetic and minimalist design dengan nilai 0,25, help users recognize, diagnose, and recover from errors dengan nilai 1 dan Help and documentation dengan nilai 0. Dari hasil heuristic evaluation yang dilakukan menunjukkan bahwa evaluator memberikan nilai 0 dan 1 aplikasi Depo Atuo 2000 Tanjung Api-Api Palembang. Hasil penilaian tersebut menunjukkan bahwa aplikasi yang buat tidak ada masalah usability dan hanya memiliki cosmetic problem sehingga aplikasi Depo Auto 2000 Tanjung Api Api Palembang  dapat dinyatakan layak untuk didistribusikan kepada pengguna akhir (end user.

  8. Corrosión a alta temperatura de acero al carbono y acero inoxidable austenítico en atmósferas contaminadas por CO2

    OpenAIRE

    Proy Pérez, Manuel

    2014-01-01

    Los efectos a veces catastróficos producidos por los procesos de corrosión a alta temperatura en atmósferas contaminadas por agentes agresivos, poseen la suficiente relevancia para ser objeto de estudio en los próximos años, debido a que en muchas ocasiones no están definidos claramente. Los aceros al carbono y los inoxidables austeníticos son materiales potencialmente utilizables en condiciones de elevada temperatura gracias a su excelente relación entre sus propiedades est...

  9. Efficiency of local Indonesia honey bees (Apis cerana L.) and stingless bee (Trigona iridipennis) on tomato (Lycopersicon esculentum Mill.) pollination.

    Science.gov (United States)

    Putra, Ramadhani Eka; Kinasih, Ida

    2014-01-01

    Tomato (Lycopersicon esculentum Mill.) is considered as one of major agricultural commodity of Indonesia farming. However, monthly production is unstable due to lack of pollination services. Common pollinator agent of tomatoes is bumblebees which is unsuitable for tropical climate of Indonesia and the possibility of alteration of local wild plant interaction with their pollinator. Indonesia is rich with wild bees and some of the species already domesticated for years with prospect as pollinating agent for tomatoes. This research aimed to assess the efficiency of local honey bee (Apis cerana L.) and stingless bee (Trigona iridipennis), as pollinator of tomato. During this research, total visitation rate and total numbers of pollinated flowers by honey bee and stingless bee were compared between them with bagged flowers as control. Total fruit production, average weight and size also measured in order to correlated pollination efficiency with quantity and quality of fruit produced. Result of this research showed that A. cerana has slightly higher rate of visitation (p>0.05) and significantly shorter handling time (p tomato flowers. However, honey bee pollinated tomato flowers more efficient pollinator than stingless bee (80.3 and 70.2% efficiency, respectively; p tomatoes were similar (p>0.05). Based on the results, it is concluded that the use of Apis cerana and Trigona spp., for pollinating tomatoes in tropical climates could be an alternative to the use of non-native Apis mellifera and bumblebees (Bombus spp.). However, more researches are needed to evaluate the cost/benefit on large-scale farming and greenhouse pollination using both bees against other bee species and pollination methods.

  10. ANALISA PEREKAMAN DATA SUARA DARI SISTEM BLACKBOX PADA KERETA API

    Directory of Open Access Journals (Sweden)

    Emy Setyaningsih

    2016-01-01

    Full Text Available             Makalah ini akan membahas tentang penerapan black box pada kereta api yang diadopsi pertama kali pada pesawat, dengan parameter perekam suara hingga waktu simpan kurang dari 1 hari 8 jam pada media penyimpanan SD Card. Tujuan dari pengujian pada makalah ini adalah membandingkan sumber suara terhadap jarak penerima, sebagai parameter perubahan tingkat suara “dB”. Sistem perekaman suara yang akan ditempatkan pada kereta api ini menggunakan modul rangkaian terintregasi WTR010. Voice record WTR010 merupakan modul rangkaian terintegrasi untuk merekam suara sendiri atau pun suara dari file music / video pada komputer dengan sangat mudah. Modul ini bisa merekam suara sendiri dan langsung di simpan ke dalam format audio. Format audio yang disediakan oleh modul voice record adalah format AD4 dan wav. Hasil pengujian modul black box yang diletakkan pada kereta api, dengan mencoba mengucapkan kata  “SAYA”,  suara dapat terekam pada modul perekam suara yang selanjutnya diolah menggunakan ”software sound editor” yang disimpan pada SD Card ber-ekstensi “wav”. Perbandingan sumber suara terhadap jarak penerima dari pengujian didapatkan sebuah persamaan regresi linier  y = -( 31x – 11  dan R² = 0.972.  Pengujian ini menghasilkan penekanan suara dB dan frekuensi sample Hz yang berbeda.  Kata kunci: black box kereta api, perekaman suara, WTR010

  11. Corrosion Cyclic Voltammetry of Two Types of Heat-Affected Zones (HAZs) of API-X100 Steel in Bicarbonate Solutions

    Science.gov (United States)

    Eliyan, Faysal Fayez; Alfantazi, Akram

    2014-12-01

    This paper examined the electrochemical corrosion behavior and corrosion products of two types of heat-affected HAZs made from API-X100 steel. Cyclic voltammetry, with different scan rates and potential ranges at 10 cycles, was applied to analyze the interdependent corrosion reactions of cathodic reduction, anodic dissolution, passivation, and transpassivation. The HAZ cooled at 60 K/s, from a peak temperature of 1470 K (1197 °C) that was held for 15 seconds, exhibited better passivation and lower cathodic activity than the HAZ cooled at 10 K/s. Increasing bicarbonate concentration, from 0.05 and 0.2 to 0.6 M, increases the anodic activity and cathodic reduction, but accordingly protects the active surfaces and enhances passivation.

  12. Rational design of monocrystalline (InP)(y)Ge(5-2y)/Ge/Si(100) semiconductors: synthesis and optical properties.

    Science.gov (United States)

    Sims, Patrick E; Chizmeshya, Andrew V G; Jiang, Liying; Beeler, Richard T; Poweleit, Christian D; Gallagher, James; Smith, David J; Menéndez, José; Kouvetakis, John

    2013-08-21

    In this work, we extend our strategy previously developed to synthesize functional, crystalline Si(5-2y)(AlX)y {X = N,P,As} semiconductors to a new class of Ge-III-V hybrid compounds, leading to the creation of (InP)(y)Ge(5-2y) analogues. The compounds are grown directly on Ge-buffered Si(100) substrates using gas source MBE by tuning the interaction between Ge-based P(GeH3)3 precursors and In atoms to yield nanoscale "In-P-Ge3" building blocks, which then confer their molecular structure and composition to form the target solids via complete elimination of H2. The collateral production of reactive germylene (GeH2), via partial decomposition of P(GeH3)3, is achieved by simple adjustment of the deposition conditions, leading to controlled Ge enrichment of the solid product relative to the stoichiometric InPGe3 composition. High resolution XRD, XTEM, EDX, and RBS indicate that the resultant monocrystalline (InP)(y)Ge(5-2y) alloys with y = 0.3-0.7 are tetragonally strained and fully coherent with the substrate and possess a cubic diamond-like structure. Molecular and solid-state ab initio density functional theory (DFT) simulations support the viability of "In-P-Ge3" building-block assembly of the proposed crystal structures, which consist of a Ge parent crystal in which the P atoms form a third-nearest-neighbor sublattice and "In-P" dimers are oriented to exclude energetically unfavorable In-In bonding. The observed InP concentration dependence of the lattice constant is closely reproduced by DFT simulation of these model structures. Raman spectroscopy and ellipsometry are also consistent with the "In-P-Ge3" building-block interpretation of the crystal structure, while the observation of photoluminescence suggests that (InP)(y)Ge(5-2y) may have important optoelectronic applications.

  13. Kombinasi Boraks dan Asam Borat sebagai Bahan Penghambat Api dan Antirayap Pada Kayu Meranti Merah

    Directory of Open Access Journals (Sweden)

    Mahdi Santoso

    2015-01-01

    Full Text Available Kayu mempunyai sifat yang mudah terbakar dan sebagian besar mempunyai keawetan alami yang rendah. Perbaikan kualitas kayu dilakukan untuk mengatasi kelemahan tersebut, salah satunya dengan mengimpregnasikan bahan kimia yang bersifat menghambat api dan beracun terhadap organisme perusak kayu. Tujuan penelitian ini adalah melihat kemampuan boraks:asam borat (1:1 untuk meningkatkan ketahanan kayu meranti merah terhadap api dan rayap kayu kering dan mengetahui proses pengawetan yang efektif. Penelitian ini menggunakan kayu meranti merah (Shorea spp berukuran 6 x 15 x 500 cm. Waktu pengawetan adalah 1, 2, dan 3 jam serta konsentrasi bahan pengawet 7% dalam 5 ulangan. Metode pengawetan menggunakan metode sel kosong dengan tekanan 12 kg/cm2 . Pengujian ketahanan terhadap api mengacu pada ASTM E 69-02 prosedur B, pengujian ketahanan terhadap rayap kayu kering mengacu pada metode rayap makan tanpa pilihan. Parameter yang diamati ialah absorpsi, retensi aktual, intensitas bakar, suhu pembakaran maksimal, lama pembaraan, mortalitas rayap kayu kering, pengurangan berat contoh uji, derajat kerusakan dan kondisi fisik sampel setelah uji bakar. Hasil penelitian menunjukkan bahwa kombinasi boraks:asam borat (1:1 memiliki efektivitas yang tinggi untuk meningkatkan ketahanan kayu meranti merah terhadap api dan rayap kayu kering. Proses pengawetan yang paling efektif adalah lama penekanan 2 jam dengan absorpsi 331 kg/m3 ; retensi aktual 28,8 kg/m3 ; intensitas bakar 10,9%; suhu pembakaran maksimal 140ºC; lama pembaraan 1,03 menit; mortalitas rayap kayu kering 100%; pengurangan berat contoh uji 0,002%; serta derajat kerusakan kategori ringan. Katakunci: penghambat api, anti rayap, boraks, Shorea spp, Cryptotermes cynocephalus   Borax and Boric Acid Combination As Fire Retardant and Anti-termite Agents on Red Meranti Wood Abstract Woods have properties which are easy to be ignited by fire and most of them have a low natural durability. Therefore, it is required to

  14. Análisis de la influencia del factor de solapamiento en el tratamiento térmico de superficies extensas de aceros por láser

    Directory of Open Access Journals (Sweden)

    García-Beltrán, A.

    2007-08-01

    Full Text Available On the basis of numerical models developed by the authors for the predictive analysis of transformation hardening of extended steel surfaces, the difficulties existing for the treatment of extended surfaces by overlapping cycles of laser heating are analyzed from a computational point of view. In this analysis, thermal and physical properties of the material are considered along with their temperature dependance. Some optimization guidelines for the irradiation parameters (including modifications of the spatial distribution of the laser beam energy are determined in order to obtain both the adequate material transformed depth and the required hardness profiles.

    Sobre la base de modelos numéricos, desarrollados por los autores para el análisis predictivo de procesos de tratamiento térmico superficial de aceros por láser, se analiza, desde un punto de vista computacional, la influencia del factor de solapamiento en el tratamiento de superficies extensas de dichos materiales mediante ciclos parcialmente superpuestos de irradiación láser. En dichos análisis, se tienen en cuenta, explícitamente, las propiedades termofísicas de los materiales considerados así como su dependencia térmica, estableciéndose, finalmente, diversos criterios de optimización de las variables de irradiación (incluyendo posibles variaciones en la distribución espacial de la energía del haz láser con el objeto de maximizar, de forma combinada, la profundidad de material transformado y el nivel de dureza alcanzado, evitando, al mismo tiempo, el sometimiento del material a ciclos térmicos degradatorios del tratamiento original, en concreto, el revenido superficial.

  15. Influence of agrochemicals fipronil and imidacloprid on the learning behavior of Apis mellifera L. honeybees - doi: 10.4025/actascianimsci.v35i4.18683

    Directory of Open Access Journals (Sweden)

    Marcela Pedraza Carrillo

    2013-10-01

    Full Text Available Agrochemicals on crop cultivated areas is a source of contamination for bees and may cause physiological and behavioral disorders and mortality. The LD50 of the pesticides fipronil and imidacloprid was determined and their effect on the learning behavior of Apis mellifera L. honeybee evaluated. LD50 was determined by the ingestion of contaminated food with different concentrations of insecticide concentrations: Fipronil (0, 0.8, 0.4, 0.2, 0.1 and 0.05 µg bee-1 and imidacloprid (0, 0.4, 0.2, 0.1, 0.05 and 0.025 µg bee-1. The method of proboscis extension reflection (PER and learning through citral odor evaluated their responses to food stimulation. LD50 obtained were 0.28 ± 0.11 and 0.10 ± 0.04 µg bee-1 for fipronil and imidacloprid, respectively. The PER test showed no significant difference (p Apis mellifera bees.  

  16. Why are SiX5(-) and GeX5(-) (X = F, Cl) stable but not CF5(-) and CCl5(-)?

    Science.gov (United States)

    Marchaj, Marzena; Freza, Sylwia; Skurski, Piotr

    2012-03-01

    The possible existence of the CF(5)(-), CCl(5)(-), SiF(5)(-), SiCl(5)(-), GeF(5)(-), and GeCl(5)(-) anions has been investigated using ab initio methods. The species containing Si and Ge as central atoms were found to adopt the D(3h)-symmetry trigonal bipyramidal equilibrium structures whose thermodynamic stabilities were confirmed by examining the most probable fragmentation channels. The ab initio re-examination of the electronic stabilities of the SiF(5)(-), SiCl(5)(-), GeF(5)(-), and GeCl(5)(-) anions [using the OVGF(full) method with the 6-311+G(3df) basis set] led to the very large vertical electron detachment (VDE) energies of 9.316 eV (SiF(5)(-)) and 9.742 eV (GeF(5)(-)), whereas smaller VDEs of 6.196 and 6.452 eV were predicted for the SiCl(5)(-) and GeCl(5)(-) species, respectively. By contrast, the high-symmetry and structurally compact anionic CF(5)(-) and CCl(5)(-) systems cannot exist due to the strongly repulsive potential predicted for the X(-) (F(-) or Cl(-)) approaching the CX(4) (CF(4) or CCl(4)). The formation of weakly bound CX(4)···X(-) (CF(4)···F(-) and CCl(4)···Cl(-)) anionic complexes (consisting of pseudotetrahedral neutral CX(4) with the weakly tethered X(-)) might be expected at low temperatures (approaching 0 K), whereas neither CX(5)(-) (CF(5)(-), CCl(5)(-)) systems nor CX(4)···X(-) (CF(4)···F(-) and CCl(4)···Cl(-)) complexes can exist in the elevated temperatures (above 0K) due to their susceptibility to the fragmentation (leading to the X(-) loss). © 2012 American Chemical Society

  17. Preparation of CuIn1-xGaxS2 (x = 0.5) flowers consisting of nanoflakes via a solvothermal method

    International Nuclear Information System (INIS)

    Liang Xiaojuan; Zhong Jiasong; Yang Fan; Hua Wei; Jin Huaidong; Liu Haitao; Sun Juncai; Xiang Weidong

    2011-01-01

    Highlights: → We report for the first time a small biomolecule-assisted route using L-cysteine as sulfur source and complexing agent to synthesis CuIn 0.5 Ga 0.5 S 2 crystals. → The possible mechanisms leading to CuIn 0.5 Ga 0.5 S 2 flowers consisting of nanoflakes were proposed. → In addition, the morphology, structure, and phase composition of the as-prepared CuIn 0.5 Ga 0.5 S 2 products were investigated in detail by XRD, FESEM, EDS, XPS, TEM (HRTEM) and SAED. - Abstract: CuIn 1-x Ga x S 2 (x = 0.5) flowers consisting of nanoflakes were successfully prepared by a biomolecule-assisted solvothermal route at 220 deg. C for 10 h, employing copper chloride, gallium chloride, indium chloride and L-cysteine as precursors. The biomolecule L-cysteine acting as sulfur source was found to play a very important role in the formation of the final product. The diameter of the CuIn 0.5 Ga 0.5 S 2 flowers was 1-2 μm, and the thickness of the flakes was about 15 nm. The obtained products were characterized by X-ray diffraction (XRD), energy dispersion spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction spectroscopy (SAED), and UV-vis absorption spectroscopy. The influences of the reaction temperature, reaction time, sulfur source and the molar ratio of Cu-to-L-cysteine (reactants) on the formation of the target compound were investigated. The formation mechanism of the CuIn 0.5 Ga 0.5 S 2 flowers consisting of flakes was discussed.

  18. Combinación de fibras de acero de última generación para el refuerzo de hormigón autocompactante

    OpenAIRE

    Alberti, Marcos; Enfedaque, Alejandro; Galvez, Jaime; Cortez, Adriana

    2018-01-01

    [ES] Dado que la mayor desventaja mecánica del hormigón son sus propiedades en tracción, las fibras normalmente se utilizan para mejorar la respuesta frente a solicitaciones de tracción y flexión, siendo las fibras de acero las más comúnmente utilizadas. Este tipo de fibras se ha utilizado con éxito en aplicaciones estructurales en los últimos 50 años y, como consecuencia, se han desarrollado nuevas fibras de acero de última generación de las que existe una bibliografía muy lim...

  19. Failure to Find Ethanol-Induced Conditioned Taste Aversion in Honey Bees (Apis mellifera L.).

    Science.gov (United States)

    Varnon, Christopher A; Dinges, Christopher W; Black, Timothy E; Wells, Harrington; Abramson, Charles I

    2018-04-24

    Conditioned taste aversion (CTA) learning is a highly specialized form of conditioning found across taxa that leads to avoidance of an initially neutral stimulus, such as taste or odor, that is associated with, but is not the cause of, a detrimental health condition. This study examines if honey bees (Apis mellifera L.) develop ethanol (EtOH)-induced CTA. Restrained bees were first administered a sucrose solution that was cinnamon scented, lavender scented, or unscented, and contained either 0, 2.5, 5, 10, or 20% EtOH. Then, 30 minutes later, we used a proboscis extension response (PER) conditioning procedure where the bees were taught to associate either cinnamon odor, lavender odor, or an air-puff with repeated sucrose feedings. For some bees, the odor of the previously consumed EtOH solution was the same as the odor associated with sucrose in the conditioning procedure. If bees are able to learn EtOH-induced CTA, they should show an immediate low level of response to odors previously associated with EtOH. We found that bees did not develop CTA despite the substantial inhibitory and aversive effects EtOH has on behavior. Instead, bees receiving a conditioning odor that was previously associated with EtOH showed an immediate high level of response. While this demonstrates bees are capable of one-trial learning common to CTA experiments, this high level of response is the opposite of what would occur if the bees developed a CTA. Responding on subsequent trials also showed a general inhibitory effect of EtOH. Finally, we found that consumption of cinnamon extract reduced the effects of EtOH. The honey bees' lack of learned avoidance to EtOH mirrors that seen in human alcoholism. These findings demonstrate the usefulness of honey bees as an insect model for EtOH consumption. Copyright © 2018 by the Research Society on Alcoholism.

  20. Experimental arguments in favour of 5/2 isospin isobars

    International Nuclear Information System (INIS)

    Nilov, A.F.; Kaidalov, A.B.; Lomkatsi, G.S.; Smolyankin, V.T.

    1978-01-01

    Search for baryon resonances with the 5/2 isotopic spin was carried out. Experimental data was obtained in π - p interactions on the hydrogen bubble chamber at 4.5 GeV/c. The investigated channels of the reaction were nπ + π + π - π - , pπ + π - π - π 0 and pπ + π - π - . The effective mass distributions of the products of the reaction were presented. The results of the paper pointed out that 5/2 isobars could be produced in the first channel which corresponded the Feynman diagram with the Δ - (1232) exchange. Particle production of the Δ ++ (1232) isobar in the second and third channels was an inderect evidence in favour

  1. Mars Atmospheric Aggregation System API

    Data.gov (United States)

    National Aeronautics and Space Administration — The {MAAS} API is an open source REST API built to help make it easier and more efficient to build interactive applications that want to utilize the wealth of...

  2. EVALUACIÓN EXPERIMENTAL DE LA RESISTENCIA A LA CORROSIÓN DE UN ACERO AISI-SAE 4140 IMPLANTADO CON IONES DE NITRÓGENO

    OpenAIRE

    PEÑA, DARIO; FONTALVO, PAOLA; ESTUPIÑAN, HUGO; NIÑO, DANNIER; VESGA, WILSON

    2009-01-01

    Se estudió la resistencia a la corrosión de un acero AISI-SAE 4140 implantado con iones de Nitrógeno mediante la técnica 3DII (Implantación Iónica Tridimensional). Se evaluaron diferentes rugosidades de las muestras implantadas mediante técnicas electroquímicas de Rp, EIS y Tafel en una salmuera al 3% de NaCl, donde se obtuvo la mayor resistencia a la corrosión para el material implantado con menor rugosidad. Se produjo la formación de una posible capa protectora estable con la inmersión de l...

  3. Beebread from Apis mellifera and Apis dorsata. Comparative Chemical Composition and Bioactivity

    Directory of Open Access Journals (Sweden)

    Otilia BOBIS

    2017-05-01

    Full Text Available Beebread is a valuable bee product, both for bee nutrition and for humans. The high nutritional and bioactive properties of beebread were evaluated by chemical composition analysis of beebread from Apis mellifera and Apis dorsata. Bee bread harvested from Romania and India, coming from Apis mellifera and Apis dorsata bees, were evaluated for their chemical composition. Analyses were made in APHIS Laboratory from USAMV Cluj, using validated methods for bee products. Lipids were determined by the Soxhlet extraction method, total protein content was determined by Kjehldahl method, sugar spectrum was determined by high performance liquid chromatography with refractive index detection (HPLC-IR. Water content of beebread samples were situated between 11.45 and 16.46%, total protein content between 16.84 and 19.19% and total lipids between 6.36 and 13.47%.  Beebread has high bioactive properties which can be expressed as antioxidant and/or antibacterial activity. Chemical composition and bioactive properties of beebread is influenced by floral origin of the pollen which the bees collect and place in combs for fermentation. Also the climatic conditions have an important role in developing different fermentation compounds, that may act as antioxidants or antibacterial agents.

  4. Flipped SU(5)xU(1){sub X} models from F-theory

    Energy Technology Data Exchange (ETDEWEB)

    Jiang Jing [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Li Tianjun, E-mail: tjli@physics.rutgers.ed [George P. and Cynthia W. Mitchell Institute for Fundamental Physics, Texas A and M University, College Station, TX 77843 (United States); Key Laboratory of Frontiers in Theoretical Physics, Institute of Theoretical Physics, Chinese Academy of Sciences, Beijing 100190 (China); Nanopoulos, Dimitri V. [George P. and Cynthia W. Mitchell Institute for Fundamental Physics, Texas A and M University, College Station, TX 77843 (United States); Astroparticle Physics Group, Houston Advanced Research Center (HARC), Mitchell Campus, Woodlands, TX 77381 (United States); Academy of Athens, Division of Natural Sciences, 28 Panepistimiou Avenue, Athens 10679 (Greece); Xie Dan [George P. and Cynthia W. Mitchell Institute for Fundamental Physics, Texas A and M University, College Station, TX 77843 (United States)

    2010-05-01

    We systematically construct flipped SU(5)xU(1){sub X} models without and with bulk vector-like particles from F-theory. To realize the decoupling scenario, we introduce sets of vector-like particles in complete SU(5)xU(1) multiplets at the TeV scale, or at the intermediate scale, or at the TeV scale and high scale. To avoid the Landau pole problem for the gauge couplings, we can only introduce five sets of vector-like particles around the TeV scale. These vector-like particles can couple to the Standard Model singlet fields, and obtain suitable masses by Higgs mechanism. We study gauge coupling unification in detail. We show that the U(1){sub X} flux contributions to the gauge couplings preserve the SU(5)xU(1){sub X} gauge coupling unification. We calculate the SU(3){sub C}xSU(2){sub L} unification scales, and the SU(5)xU(1){sub X} unification scales and unified couplings. In most of our models, the high-scale or bulk vector-like particles can be considered as string-scale threshold corrections since their masses are close to the string scale. Furthermore, we discuss the phenomenological consequences of our models. In particular, in the models with TeV-scale vector-like particles, the vector-like particles can be observed at the Large Hadron Collider, the proton decay is within the reach of the future Hyper-Kamiokande experiment, the lightest CP-even Higgs boson mass can be increased, the hybrid inflation can be naturally realized, and the correct cosmic primordial density fluctuations can be generated.

  5. Hyper-X Research Vehicle - Artist Concept Mounted on Pegasus Rocket Attached to B-52 Launch Aircraft

    Science.gov (United States)

    1997-01-01

    This artist's concept depicts the Hyper-X research vehicle riding on a booster rocket prior to being launched by the Dryden Flight Research Center's B-52 at about 40,000 feet. The X-43A was developed to flight test a dual-mode ramjet/scramjet propulsion system at speeds from Mach 7 up to Mach 10 (7 to 10 times the speed of sound, which varies with temperature and altitude). Hyper-X, the flight vehicle for which is designated as X-43A, is an experimental flight-research program seeking to demonstrate airframe-integrated, 'air-breathing' engine technologies that promise to increase payload capacity for future vehicles, including hypersonic aircraft (faster than Mach 5) and reusable space launchers. This multiyear program is currently underway at NASA Dryden Flight Research Center, Edwards, California. The Hyper-X schedule calls for its first flight later this year (2000). Hyper-X is a joint program, with Dryden sharing responsibility with NASA's Langley Research Center, Hampton, Virginia. Dryden's primary role is to fly three unpiloted X-43A research vehicles to validate engine technologies and hypersonic design tools as well as the hypersonic test facility at Langley. Langley manages the program and leads the technology development effort. The Hyper-X Program seeks to significantly expand the speed boundaries of air-breathing propulsion by being the first aircraft to demonstrate an airframe-integrated, scramjet-powered free flight. Scramjets (supersonic-combustion ramjets) are ramjet engines in which the airflow through the whole engine remains supersonic. Scramjet technology is challenging because only limited testing can be performed in ground facilities. Long duration, full-scale testing requires flight research. Scramjet engines are air-breathing, capturing their oxygen from the atmosphere. Current spacecraft, such as the Space Shuttle, are rocket powered, so they must carry both fuel and oxygen for propulsion. Scramjet technology-based vehicles need to carry

  6. BcL-xL Conformational Changes upon Fragment Binding Revealed by NMR

    Science.gov (United States)

    Aguirre, Clémentine; ten Brink, Tim; Walker, Olivier; Guillière, Florence; Davesne, Dany; Krimm, Isabelle

    2013-01-01

    Protein-protein interactions represent difficult but increasingly important targets for the design of therapeutic compounds able to interfere with biological processes. Recently, fragment-based strategies have been proposed as attractive approaches for the elaboration of protein-protein surface inhibitors from fragment-like molecules. One major challenge in targeting protein-protein interactions is related to the structural adaptation of the protein surface upon molecular recognition. Methods capable of identifying subtle conformational changes of proteins upon fragment binding are therefore required at the early steps of the drug design process. In this report we present a fast NMR method able to probe subtle conformational changes upon fragment binding. The approach relies on the comparison of experimental fragment-induced Chemical Shift Perturbation (CSP) of amine protons to CSP simulated for a set of docked fragment poses, considering the ring-current effect from fragment binding. We illustrate the method by the retrospective analysis of the complex between the anti-apoptotic Bcl-xL protein and the fragment 4′-fluoro-[1,1′-biphenyl]-4-carboxylic acid that was previously shown to bind one of the Bcl-xL hot spots. The CSP-based approach shows that the protein undergoes a subtle conformational rearrangement upon interaction, for residues located in helices 2, 3 and the very beginning of 5. Our observations are corroborated by residual dipolar coupling measurements performed on the free and fragment-bound forms of the Bcl-xL protein. These NMR-based results are in total agreement with previous molecular dynamic calculations that evidenced a high flexibility of Bcl-xL around the binding site. Here we show that CSP of protein amine protons are useful and reliable structural probes. Therefore, we propose to use CSP simulation to assess protein conformational changes upon ligand binding in the fragment-based drug design approach. PMID:23717610

  7. Updated API document 6A will close API-ISO 9000 gap. [Oil and gas wellhead standards

    Energy Technology Data Exchange (ETDEWEB)

    Bell, S.

    1993-10-01

    The 17th edition of the American Petroleum Institute's (API) document 6A, covering wellheads and their components, is due early next year. As the API vs. International Standards Organization (ISO) 9000 struggle continues, this edition of 6A eliminates some unnecessary specifications, clarifies others, and includes metric specifications accepted by the ISO. The 17th edition will clarify some of the interpretations from earlier editions and further advise users how to acquire the API monogram. The goal of this edition is to make 6A acceptable to ISO as an international document so API can maintain control over petroleum equipment specifications and provide input and guidance in future regulations.

  8. Caracterização físico-química de méis de Apis mellifera L. da região noroeste do Estado do Rio Grande do Sul Physicochemical characterization of Apis mellifera L. honeys from the northwest region of Rio Grande do Sul State

    Directory of Open Access Journals (Sweden)

    Juliane Elisa Welke

    2008-09-01

    Full Text Available O objetivo deste trabalho foi determinar a composição físico-química de méis de Apis mellifera L. produzidos em dois anos consecutivos na região noroeste do Estado do Rio Grande do Sul, Brasil. As características físico-químicas de 36 amostras de mel foram comparadas utilizando o teste T de Student e a adequação aos padrões da legislação brasileira da qualidade do mel foi verificada. Os resultados das análises dos méis variaram para as características analisadas conforme segue: pH (3,3-4,4, umidade (14,7-19,8%, acidez total (16,9-49,2meq kg-1, hidroximetilfurfural (0,15-48,3mg kg-1, açúcares redutores (60,1-75,9%, açúcares não-redutores (1,35-5,99%, cinzas (0,05-0,47% e sólidos insolúveis (0,016-0,27g kg-1. A análise estatística das amostras de mel produzidas em dois anos consecutivos mostrou que houve diferença significativa na umidade, na acidez e na hidroximetilfurfural. Os méis produzidos nesta região apresentam boa qualidade e características físico-químicas compatíveis aos padrões da legislação brasileira.The objective of this research was to determine the physicochemical composition of Apis mellifera L. honeys produced in two consecutive years in the northwest region of Rio Grande do Sul State, Brazil. The physicochemical characteristics of 36 honey samples were compared using Student’s T-test and their adequacy to standards established by the Brazilian legislation for honey quality was checked. The results varied as follows: pH (3.3-4.4, moisture (14.7-19.8%, acidity (16.9-49.2meq kg-1, hydroxymethylfurfural content (0.15-48.3mg kg-1, reducing sugar (60.1-75.9%, non-reducing sugar (1.35-5.99%, ashes (0.05-0.47% and solids non-soluble in water (0.016-0.27g kg-1. The statistical analyses of honey samples produced in two consecutive years showed that the moisture, acidity and hydroxymethylfurfural content varied significantly. The honey samples produced in this region were in accordance with the

  9. SU(n)c x SU(m)L x U(1)N generalizations of the standard model

    International Nuclear Information System (INIS)

    Pleitez, V.

    1993-01-01

    Generalizations of the Standard Model which are based on the gauge symmetry SU(n) c x SU(m) L x U(1) N are considered. Although the most interesting possibility occurs when n = 3, it will be considered also the cases n = 4,5, both with m = 3,4. It will also be given possible grand unification scenarios. (author). 18 refs

  10. Variation morphogeometrics of Africanized honey bees (Apis mellifera in Brazil

    Directory of Open Access Journals (Sweden)

    Lorena A. Nunes

    2012-09-01

    Full Text Available The morphometrics of the honey bee Apis mellifera L., 1758 has been widely studied mainly because this species has great ecological importance, high adaptation capacity, wide distribution and capacity to effectively adapt to different regions. The current study aimed to investigate the morphometric variations of wings and pollen baskets of honey bees Apis mellifera scutellata Lepeletier, 1836 from the five regions in Brazil. We used geometric morphometrics to identify the existence of patterns of variations of shape and size in Africanized honey bees in Brazil 16 years after the classic study with this species, allowing a temporal and spatial comparative analysis using new technological resources to assess morphometrical data. Samples were collected in 14 locations in Brazil, covering the five geographical regions of the country. The shape analysis and multivariate analyses of the wing allowed to observe that there is a geographical pattern among the population of Apis mellifera in Brazil. The geographical variations may be attributed to the large territorial extension of the country in addition to the differences between the bioregions.

  11. Pollen types and levels of total phenolic compounds in propolis produced by Apis mellifera L. (Apidae in an area of the Semiarid Region of Bahia, Brazil

    Directory of Open Access Journals (Sweden)

    VANESSA R. MATOS

    2014-03-01

    Full Text Available Twenty-two propolis samples produced by Apis mellifera L. in an area of the Semiarid region the the State of Bahia (Agreste of Alagoinhas, Brazil, were palynologically analyzed and quantified regarding their levels of total phenolic compounds. These samples were processed using the acetolysis technique with the changes suggested for use with propolis. We found 59 pollen types belonging to 19 families and 36 genera. The family Fabaceae was the most representative in this study with nine pollen types, followed by the family Asteraceae with seven types. The types Mikania and Mimosa pudica occurred in all samples analyzed. The types Mimosa pudica and Eucalyptus had frequency of occurrence above 50% in at least one sample. The highest similarity index (c. 72% occurred between the samples ER1 and ER2, belonging to the municipality of Entre Rios. Samples from the municipality of Inhambupe displayed the highest (36.78±1.52 mg/g EqAG and lowest (7.68 ± 2.58 mg/g EqAG levels of total phenolic compounds. Through the Spearman Correlation Coefficient we noticed that there was a negative linear correlation between the types Mimosa pudica (rs = -0.0419 and Eucalyptus (rs = -0.7090 with the profile of the levels of total phenolic compounds of the samples.

  12. Delineamentos (1/5(5³ Desings (1/5(5³

    Directory of Open Access Journals (Sweden)

    Armando Conagin

    1977-01-01

    Full Text Available É descrita a análise estatística de um grupo especial de fatoriais fracionados (1/5 (5³, utilizando os modelos quadráticos e com raiz quadrada; tal estudo foi desenvolvido pelos autores visando principalmente sua aplicação em experimentos agronômicos com fertilizantes. Estes delineamentos fatoriais se originaram da superposição de três dos quatro quadrados latinos ortogonais 5x5, sendo obtidos três conjuntos básicos, designados por Tipo I, II, III, Tipo I, II, IV e Tipo I, III, IV; o último deles é apresentado: 111 245 324 453 532 222 351 435 514 143 333 412 541 125 254 444 523 152 231 315 555 134 213 342 42 O modelo quadrático com dez parâmetros é dado por: Yijk = b0x0 +b li x li + b lj x lj + b lk x lk + b2i x2i + b2j x2j + b2k x2k + + b lilj x lilj + b lilk x lilk + b ljlk x ljlk + x ijk em que x lm = a1 + Xm, x2m = a2 + g2Xm + X²m , com m= i,j,k; os níveis em cada fator variam de 1 a 5; com as condições de ortogonalidade Sx lm=0, Sx2m=0, Sx lm x2m=0, resulta Sxlm=-3+Xm e Sx2m= 7-6Xm+X²m, de onde se tem: x l1=-2; x l2=-1; x l3=0; x l4=1; x l5=2; x21=2; x22=-1; x23=-2; x24=-1; x25=2, para cada índice i,j,k. O coeficiente linear para cada fator pode ser estimado independentemente; os coeficientes quadráticos e das interações linear x linear são estimados a partir de uma matriz simétrica completa 6x6. Consequentemente, na análise da variância as somas de quadrados dos componentes lineares são independentes, mas as somas de quadrados dos componentes quadráticos e das interações são confundidas e, por isso, testadas conjuntamente. Se a contribuição de um fator e sua interação com os outros são negligíveis, podem ser calculadas estimativas independentes dos coeficientes linear e quadrático dos outros dois fatores e sua interação correspondente. Por outro lado, se todos os fatores são importantes mas suas interações são negligíveis, os coeficientes lineares e quadráticos de cada fator são estimados

  13. Intro to the Zotero API

    Directory of Open Access Journals (Sweden)

    Amanda Morton

    2013-04-01

    Full Text Available In this lesson, you’ll learn how to use python with the Zotero API to interact with your Zotero library. The Zotero API is a powerful interface that would allow you to build a complete Zotero client from scratch if you so desired. But like most APIs, it works in small, discrete steps, so we have to build our way up to the complicated requests we might want to use to access our Zotero libraries. But this incremental building gives us plenty of time to learn as we go along.

  14. Bluetooth API Implementation into Android

    Directory of Open Access Journals (Sweden)

    Konev Sergey

    2017-01-01

    Full Text Available Bluetooth is a popular method of communication between devices. Many smartphones today have the capability to communicate using Bluetooth. Android developers sometimes need to use Bluetooth in their projects. Android OS provides a powerful API for Bluetooth that allows to simplify scanning the environment for devices, pairing and connecting, data transfer between devices and more. However, utilizing the Bluetooth API can be difficult for first-time users. The objective of this article is to demonstrate the key points of implementing Bluetooth API in the Android application.

  15. Fertility and reproductive rate of Varroa mite, Varroa destructor, in native and exotic honeybee, Apis mellifera L., colonies under Saudi Arabia conditions

    Directory of Open Access Journals (Sweden)

    Yehya Alattal

    2017-07-01

    Full Text Available Varroa mite is the most destructive pest to bee colonies worldwide. In Saudi Arabia, preliminary data indicated high infestation levels in the exotic honeybee colonies; such as Apis mellifera carnica and Apis mellifera ligustica, compared to native honeybee subspecies Apis mellifera jemenitica, which may imply higher tolerance to Varroasis. In this study, fertility and reproductive rate of Varroa mite, Varroa destructor, in capped brood cells of the native honeybee subspecies were investigated and compared with an exotic honeybee subspecies, A. m. carnica. Mite fertility was almost alike (87.5% and 89.4% in the native and craniolan colonies respectively. Similarly, results did not show significant differences in reproduction rate between both subspecies (F = 0.66, Pr > F = 0.42. Number of adult Varroa daughters per fertile mother mite was 2.0 and 2.1 for native and craniolan honeybee subspecies respectively. This may indicate that mechanisms of keeping low infestation rates in the native honeybee colonies are not associated with Varroa reproduction. Therefore, potential factors of keeping lower Varroa infestation rates in native honey bee subspecies should be further investigated.

  16. Restful API Architecture Based on Laravel Framework

    Science.gov (United States)

    Chen, Xianjun; Ji, Zhoupeng; Fan, Yu; Zhan, Yongsong

    2017-10-01

    Web service has been an industry standard tech for message communication and integration between heterogeneous systems. RESTFUL API has become mainstream web service development paradigm after SOAP, how to effectively construct RESTFUL API remains a research hotspots. This paper presents a development model of RESTFUL API construction based on PHP language and LARAVEL framework. The key technical problems that need to be solved during the construction of RESTFUL API are discussed, and implementation details based on LARAVEL are given.

  17. Integrable Equations of the Form qt=L1(x,t,q,qx,qxx)qxxx+L2(x,t,q,qx,qxx)

    International Nuclear Information System (INIS)

    Satir, Ahmet

    2003-01-01

    Integrable equations of the form q t =L 1 (x,t,q,q x ,q xx )q xxx +L 2 (x,t,q,q x ,q xx ) are considered using linearization. A new type of integrable equations which are the generalization of the integrable equations of Fokas and Ibragimov and Shabat are given

  18. Lactobacillus panisapium sp. nov., from honeybee Apis cerana bee bread.

    Science.gov (United States)

    Wang, Cong; Huang, Yan; Li, Li; Guo, Jun; Wu, Zhengyun; Deng, Yu; Dai, Lirong; Ma, Shichun

    2018-03-01

    A novel facultatively anaerobic, Gram-stain-positive, non-motile, non-spore-forming, catalase-negative bacterium of the genus Lactobacillus, designated strain Bb 2-3 T , was isolated from bee bread of Apis cerana collected from a hive in Kunming, China. The strain was regular rod-shaped. Optimal growth occurred at 37 °C, pH 6.5 with 5.0 g l -1 NaCl. The predominant fatty acids were C18 : 1ω9c, C16 : 0 and C19 : 0 iso. Respiratory quinones were not detected. Seven glycolipids, three lipids, phosphatidylglycerol and diphosphatidylglycerol were detected. The peptidoglycan type A4α l-Lys-d-Asp was determined. Strain Bb 2-3 T was closely related to Lactobacillus bombicola DSM 28793 T , Lactobacillus apis LMG 26964 T and Lactobacillus helsingborgensis DSM 26265 T , with 97.8, 97.6 and 97.0 % 16S rRNA gene sequence similarity, respectively. A comparison of two housekeeping genes, rpoA and pheS, revealed that strain Bb 2-3 T was well separated from the reference strains of species of the genus Lactobacillus. The average nucleotide identity between strain Bb 2-3 T and the type strains of closely related species was lower than the 95-96 % threshold value for delineation of genomic prokaryotic species. The G+C content of the genomic DNA of strain Bb 2-3 T was 37.4 mol%. On the basis of phenotypic, chemotaxonomic and phylogenetic analyses, strain Bb 2-3 T is proposed to represent a novel species of the genus Lactobacillus, for which we propose the name Lactobacillus panisapium sp. nov. The type strain is Bb 2-3 T (=DSM 102188 T =ACCC 19955 T ).

  19. Do agrochemicals used during soybean flowering affect the visits of Apis mellifera L.?

    Energy Technology Data Exchange (ETDEWEB)

    Fagúndez, G.A.; Blettler, D.C.; Krumrick, C.G.; Bertos, M.A.; Trujillo, C.G.

    2016-11-01

    In the Pampa region of Argentina, most beehives are situated near to soybean [Glycine max (L.) Merr.] crop and honey bees (Apis mellifera L.) use its floral resources. Soybean is often sprayed with pesticides but very little is known about their repellent action against bees. This study evaluates the visit of honey bees to crop after the application of agrochemicals aiming to check for repellency of them and estimate the possible impact on crop pollination. For this, six treatments were used (glyphosate + cypermethrin; glyphosate; cypermethrin; lambda-cyhalothrin; methoxyfenocide; Bacillus thuringiensis) and developed on plots of 625 m2, located in Oro Verde (Argentina), applying two sprays during the crop flowering. The bees were captured using entomological net every 4 days in three different times from the day after the first spraying and up the end of crop flowering. The results showed very little or no repellent action of pesticides on A. mellifera, noting that it foraged on soybean flowers regardless of the temporal proximity and the type of product used in sprays. Possible causes are discussed and the need for larger studies is evident in field conditions related to pesticides repellency and mixtures. Also, further evaluation of the effects of the different chemical formulations available on the market and used regionally where the subspecies A. mellifera can be found. Simultaneously some management practices that could help minimize the risk of contamination are mentioned; the use of defensive crop products of biological origin is encouraged as well as further research in this topic. (Author)

  20. Produtos naturais no comportamento defensivo de Apis mellifera L. = Natural products in the defensive behaviour of Apis mellifera L.

    Directory of Open Access Journals (Sweden)

    Renata Leonardo Lomele

    2010-07-01

    Full Text Available Os objetivos do estudo foram investigar a influência de produtos naturais como capim-limão (Cymbopogon citratus, folhas de abacateiro (Persea americana, casca de café (Coffea arabica e sementes de mamona (Ricinus communis na defensividade de Apis mellifera, e avaliar o efeito destes produtos no desenvolvimento populacional da colmeia. O comportamento defensivo foi avaliado por meio do tempo da primeira ferroada (TPF, número de ferrões (NFB e, o desenvolvimento populacional, pela área de cria aberta e fechada. Observou-se que o tratamento fumaça + sete sementes de mamona apresentou aumento significativo no TPF, em relação ao tratamento sem e com fumaça de maravalha. Com relação ao NFB, verificou-se que os tratamentos fumaça de maravalha + sete sementes de mamona e fumaça de maravalha + 20% de folhas de café foram diferentes do tratamento sem e com fumaça. Os demais tratamentos não diferiram significativamente em relação ao uso da fumaça ou sua ausência. A casca de café e a semente de mamona nãointerferiram no desenvolvimento populacional, sugerindo que estes compostos não foram tóxicos. Pode-se concluir que o uso de sementes de mamona e casca de café na fumaça pode representar importante ferramenta para a redução da defensividade, sem promover toxicidade para A. mellifera.The goal was to investigate the influence of natural products such as lemongrass (Cymbopogon citratus, dried avocado leaves (Persea americana, coffee husk (Coffea arabica and castor bean (Ricinus communis in the defense of Apis mellifera, as well the effect of these products on the population development of the beehive. Defensive behavior was evaluated by time of first sting (TFS and number of stingers (NS, and population development, by open brood area and operculated brood. It was observed that the treatment with smoke + seven castor beans presented significant increase in the TFS, for treatment without and with smoke. Regarding NS, it was verified

  1. Bcl-xL stimulates Bax relocation to mitochondria and primes cells to ABT-737.

    Science.gov (United States)

    Renault, Thibaud T; Teijido, Oscar; Missire, Florent; Ganesan, Yogesh Tengarai; Velours, Gisèle; Arokium, Hubert; Beaumatin, Florian; Llanos, Raul; Athané, Axel; Camougrand, Nadine; Priault, Muriel; Antonsson, Bruno; Dejean, Laurent M; Manon, Stéphen

    2015-07-01

    Bax cytosol-to-mitochondria translocation is a central event of the intrinsic pathway of apoptosis. Bcl-xL is an important regulator of this event and was recently shown to promote the retrotranslocation of mitochondrial Bax to the cytosol. The present study identifies a new aspect of the regulation of Bax localization by Bcl-xL: in addition to its role in Bax inhibition and retrotranslocation, we found that, like with Bcl-2, an increase of Bcl-xL expression levels led to an increase of Bax mitochondrial content. This finding was substantiated both in pro-lymphocytic FL5.12 cells and a yeast reporting system. Bcl-xL-dependent increase of mitochondrial Bax is counterbalanced by retrotranslocation, as we observed that Bcl-xLΔC, which is unable to promote Bax retrotranslocation, was more efficient than the full-length protein in stimulating Bax relocation to mitochondria. Interestingly, cells overexpressing Bcl-xL were more sensitive to apoptosis upon treatment with the BH3-mimetic ABT-737, suggesting that despite its role in Bax inhibition, Bcl-xL also primes mitochondria to permeabilization and cytochrome c release. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Out-of-equilibrium nanocrystalline R1-s(Fe,M)5+2s alloys (R=Sm,Pr; M=Co,Si,Ga)

    International Nuclear Information System (INIS)

    Bessais, L.; Djega-Mariadassou, C.

    2005-01-01

    The out-of-equilibrium hexagonal P6/mmm R 1-s (Fe,M) 5+2s (R=Sm,Pr and M=Co, Si or Ga) intermetallics are obtained by controlled nanocrystallization. A model is presented to explain the structure of the hexagonal phases, which stoichiometry is consistent with Sm(Fe,M) 9 and R(Fe,Ti,Co) 10 . The Curie temperatures increase versus Ga, Si, Co content. The analysis of the Moessbauer spectra leads to monotonous variation of the hyperfine parameters. The refinement of the Moessbauer spectra was performed on the basis of the correlation between Wigner-Seitz cell volumes obtained from X-ray diffraction results and isomer shifts. The abundance of each magnetic site was calculated by the multinomial distribution law. For a given substituting Co, Si, Ga content, the sequence for the isomer shift in the hexagonal cell is 2e>3g>6l. With increasing M content, the isomer shift of the 3g site remains quasi-constant. Those approaches lead to the location of Si, Ga, Co in 3g site, Ti in 6l site. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  3. 1 CFR 5.2 - Documents required to be filed for public inspection and published.

    Science.gov (United States)

    2010-01-01

    ... inspection and published. 5.2 Section 5.2 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER THE FEDERAL REGISTER GENERAL § 5.2 Documents required to be filed for public inspection and published... Register and published in the Federal Register: (a) Presidential proclamations and Executive orders in the...

  4. Bcl-x(L) expression in vivo in rheumatoid synovium.

    LENUS (Irish Health Repository)

    Busteed, S

    2012-02-03

    To examine the expression of the apoptosis regulatory protein, Bcl-x(L), in the synovium of patients with rheumatoid arthritis (RA) and osteoarthritis (OA). Immunohistochemistry for Bcl-x(L) was carried out on synovial samples from patients with RA and OA. Reverse transcriptase polymerase chain reaction (RT-PCR) and Western blot analysis were performed to qualitatively examine the expression of Bcl-x(L). Bcl-x(L) expression was detected in the lining, endothelium and inflammatory cells of both RA (n=20) and OA (n=10) samples. However, there was significantly more expression in the lining of RA synovium compared to OA (77 vs 61%, p<0.05). Many of the positive cells in the RA subsynovium were noted to be plasma cells. There was a significant correlation between Bcl-x(L) expression and the number of inflammatory cells in the subsynovium of RA and OA patients (r (s)=0.376, p<0.05, n=30). Age and disease duration did not correlate with Bcl-x(L) expression in rheumatoid patients. Bcl-x(L) may play a role in the extended survival of synoviocytes and inflammatory cells in rheumatoid synovium.

  5. Índices de prevalencia del ácaro Varroa destructor (Acari: Varroidae en cuadros de cría nuevos o previamente utilizados por Apis mellifera (Hymenoptera: Apidae Infestation levels of the mite Varroa destructor (Acari: Varroidae in new and old honeybee brood combs of Apis mellifera (Hymenoptera: Apidae

    Directory of Open Access Journals (Sweden)

    Jorge, A. Marcangeli

    2007-07-01

    Full Text Available El objetivo de esta investigación fue comparar los niveles de infestación de Varroa destructor (Anderson & Trueman en panales de cría nuevos y viejos, en colonias de la abeja criolla (híbrido de Apis mellifera mellifera (Linnaeus y Apis mellifera ligustica Spinola. El trabajo se llevó a cabo en un apiario ubicado en Coronel Vidal, provincia de Buenos Aires, durante la primavera del año 2005. Se trabajó sobre 20 colmenas tipo Langstroth, de un híbrido de Apis mellifera (Linnaeus infestadas naturalmente por el ácaro Varroa destructor, y seleccionadas al azar. En cada una de ellas se escogió un panal de 2 años (viejo que se colocó en el centro del nido de cría, junto con un panal recientemente labrado por las abejas (nuevo. Luego de que ambos cuadros fueran operculados, se los extrajo y se llevaron al laboratorio para su posterior análisis. Cada una de las celdas de cría se desoperculó e inspeccionó en busca de ácaros, registrándose el número de hembras de ácaros que habían ingresado para su reproducción, se calculó el nivel de infestación como el cociente entre el número de celdas infestadas por ácaros y el número total de celdas inspeccionadas. Los resultados mostraron que los panales viejos presentaron niveles de infestación significativamente superiores a los registrados en panales nuevos (13,52% ± 3,35 y 6,18% ± 2,12 respectivamente; t = 10,62; p = 1,9 E-9; g. l.= 19. El mismo patrón fue observado en el número promedio de ácaros por panal (443,3 ± 70,54 y 217,85 ± 51,76 para panales viejos y nuevos respectivamente; t = 23,87; p = 1,24 E-15; g. l.= 19. Los ácaros presentan una marcada preferencia por los panales viejos. Esta selección estaría guiada por olores propios de las celdas, que actuarían como atrayentes. Además, posiblemente enmascaran su presencia de esta manera y evitan así ser detectados y eliminados por las abejas nodrizas mediante los comportamientos higiénicos.The aim of this work was to

  6. Comparación de la microestructura y propiedades de impacto de dos materiales compuestos laminados de acero de ultraalto contenido de carbono

    Directory of Open Access Journals (Sweden)

    Pozuelo, M.

    2004-04-01

    Full Text Available Two ferrous laminated composites containing six layers have been processed by roll bonding. One of them consists of three layers of an ultrahigh carbon steel (1.3%C UHCS interlayered with other three layers of a microalloyed steel. The other composite consists of three layers of UHCS and three layers of a mild steel. Microstructure, Vickers hardness and impact properties have been studied. The absorbed energy values of the two laminated composites were higher than that of the UHCS.

    Se procesaron mediante laminación en caliente dos materiales compuestos laminados de acero de ultraalto contenido de carbono (AUAC, 1,3%C de seis capas cada uno: El primero está compuesto por tres capas de AUAC alternadas con tres capas de un acero microaleado, y el segundo con tres del mismo AUAC alternadas con tres de un acero suave. Se ha realizado un estudio de sus microestructuras, dureza Vickers y propiedades de impacto. Se han mejorado los valores de energía absorbida de los dos materiales compuestos laminados respecto al del AUAC.

  7. The gene dosage effect of the rad52 mutation on X-ray survival curves of tetraploid yeast strains

    International Nuclear Information System (INIS)

    Ho, K.S.Y.

    1975-01-01

    The mutation rad52 in the yeast Saccharomyces cerevisiae confers sensitivity to X-rays. The gene dosage effect of this mutation on X-ray survival curves of tetraploid yeast strains is shown. With increasing number of rad52 alleles, both a decrease in the survival for a given dose and a decrease in the survival curve shoulder width are observed. The generation of such a family of survival curves using three different mathematical models is discussed

  8. Pollen harvest by Apis mellifera L. (Hymenoptera: Apidae in the Dourados region, Mato Grosso do Sul state (Brazil Pólen coletado por Apis mellifera L. (Hymenoptera: Apidae na região de Dourados, estado de Mato Grosso do Sul (Brasil

    Directory of Open Access Journals (Sweden)

    D'Apolito

    2010-12-01

    Full Text Available We present data on the pollen harvest by Apismellifera L. at a central-western Brazil site not yet studied. Corbiculae pollen loads were collected during one year in front of the hive, acetolysed and slides mounted for optical microscopy. Identification followed comparisons with a local pollen collection. Forty-two pollen types were utilized by the bee; the most important families were Myrtaceae, Asteraceae, Euphorbiaceae, Brassicaceae and Poaceae. The genus/species level ranking of relative importance showed Eucalyptus (19%, Raphanus raphanistrum (13%, Poaceae type 2 (7.5%, Jatropha cf. gossypiifolia (7% and Sapium glandulatum (6.5%. Overall, the majority of pollen types (80% were not abundantly harvested, and a minority (4% reached values of 10%. Given that the study area has cultivated plants and not natural vegetation, we indicate most of the identified species as manageable and point out that weedy vegetation can be an important food source for bees since it frequently occurred in the pollen spectra even within a totally cultivated area.Apresentamos dados sobre a coleta de pólen por Apis mellifera L. em uma localidade no centro-oeste do Brasil, ainda não estudada. Cargas corbiculares de pólen foram coletadas durante um ano em frente ao ninho, acetolisadas e montadas em lâminas para microscopia óptica. A identificação foi feita por comparação com uma coleção de referência local. Quarenta e dois tipos polínicos foram utilizados pelas abelhas; as famílias mais importantes foram Myrtaceae, Asteraceae, Euphorbiaceae, Brassicaceae e Poaceae. O ranqueamento de importância relativa para gênero/espécie mostrou Eucalyptus (19%, Raphanus raphanistrum (13%, Poaceae tipo 2 (7,5%, Jatropha cf. gossypiifolia (7% e Sapium glandulatum (6,5%. No geral, a maioria dos recursos (80% não foi utilizada com abundância, e uma minoria (4% alcançou valores de 10%. Dado que a área de estudo não possui uma vegetação natural, mas cultivares, n

  9. S-N Curves of high resistance steels in the gigacyclic regime; Curvas S-N de aceros de alta resistencia dentro del regimen gigaciclico

    Energy Technology Data Exchange (ETDEWEB)

    Marinez G, I [Conservatoire National des Arts et Metiers-Institut des Technologies et des Materiaux Avances (CNAM-ITMA), Paris (France); Dominguez A, G [Instituto Tecnologico de Celaya, Guanajuato (Mexico); Bathias, C [Conservatoire National des Arts et Metiers-Institut des Technologies et des Materiaux Avances (CNAM-ITMA), Paris (France)

    2004-04-15

    In this paper, the fatigue behavior of high strength steel used for mechanical parts has been investigated in the gigacycle fatigue regime. An experimental study has been carried out with both: R = 0.1 (perlitic-ferritic steel) and R = -1 (perlitic-ferritic steel, bainitic steel, martensitic steels) loads, at a high frequency of 20 khz up to 1010 cycles, to determine the S-N curves when fatigue life is more than 107 cycles. Comparison of experimental results at frequencies of 20 khz and 30 Hz with R = -1, shows that the S-N curve has a good agreement between 105 and 107 cycles for the high strength steels, Furthermore, fracture surface observations are made by SEM; the transition of crack initiation site is described. The generalization of gigacycle fatigue behavior is analyzed. More often initiation of fatigue crack at 109 cycles is a bulk phenomenon with an important effect of stress concentration due to mineral inclusions or perlitic platelets. Thus, the Murakami model is efficient when we can measure the defects associated with fracture, but it can not take into account the microstructure effect related to platelets phenomenon. [Spanish] En este trabajo se investigo el comportamiento en fatiga gigaciclica de varios aceros de alta resistencia utilizados en la industria automotriz. El estudio experimental se llevo a cabo utilizando dos diferentes valores de carga: R = 0.1 (acero perlitoferritico) y R = -1 (acero perlito-ferritico, acero bainitico, aceros martensiticos), a una frecuencia de ensayo de 20 kHz y hasta 1010 ciclos, para determinar las curvas S-N arriba de 107 ciclos. La comparacion de resultados experimentales obtenidos utilizando frecuencias de ensayo de 20 kHz y 30 Hz con la relacion de carga R = - 1, muestran la continuidad de las curvas S-N entre 105 y 107 ciclos para estos aceros de alta resistencia. Por otro lado, observaciones de la superficie de fractura se efectuaron utilizando el microscopio electronico de barrido; se describe la transicion

  10. A new synthetic drug 5-(2-aminopropyl)indole (5-IT) induces rewarding effects and increases dopamine D1 receptor and dopamine transporter mRNA levels.

    Science.gov (United States)

    Botanas, Chrislean Jun; Yoon, Seong Shoon; de la Peña, June Bryan; Dela Peña, Irene Joy; Kim, Mikyung; Custodio, Raly James; Woo, Taeseon; Seo, Joung-Wook; Jang, Choon-Gon; Yang, Ji Seul; Yoon, Yoon Mi; Lee, Yong Sup; Kim, Hee Jin; Cheong, Jae Hoon

    2018-04-02

    In recent years, there has been a marked increase in the use of recreational synthetic psychoactive substances, which is a cause of concern among healthcare providers and legal authorities. In particular, there have been reports on the misuse of 5-(2-aminopropyl)indole (5-API; 5-IT), a new synthetic drug, and of fatal and non-fatal intoxication. Despite these reports, little is known about its psychopharmacological effects and abuse potential. Here, we investigated the abuse potential of 5-IT by evaluating its rewarding and reinforcing effects through conditioned place preference (CPP) (1, 10, and 30 mg/kg, i.p.) in mice and self-administration test (0.1, 0.3, 1, and 3 mg/kg/inf., i.v.) in rats. We also examined whether 5-IT (1, 3, and 10 mg/kg, i.p.) induces locomotor sensitization in mice following a 7-day treatment and drug challenge. Then, we explored the effects of 5-IT (10 mg/kg, i.p.) on dopamine-related genes in the striatum, prefrontal cortex (PFC), and substantia nigra pars compacta (SNc)/ventral tegmental (VTA) of mice by quantitative real-time polymerase chain reaction. 5-IT produced CPP in mice but was not reliably self-administered by rats. 5-IT also induced locomotor sensitization following repeated administration and drug challenge. Moreover, 5-IT increased mRNA levels of dopamine D1 receptor in the striatum and PFC and dopamine transporter in the SNc/VTA of mice. These results indicate that 5-IT has psychostimulant and rewarding properties, which may be attributed to its ability to affect the dopaminergic system in the brain. These findings suggest that 5-IT poses a substantial risk for abuse and addiction in humans. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. In vitro evaluation of the effects of some plant essential oils on Ascosphaera apis, the causative agent of Chalkbrood disease

    Directory of Open Access Journals (Sweden)

    Mohammad Javed Ansari

    2017-07-01

    Full Text Available Ascosphaera apis is one of the major fungal pathogens of honey bee broods and the causative agent of Chalkbrood disease. The factors responsible for the pathogenesis of Chalkbrood disease are still not fully understood, and the increasing resistance of A. apis to commonly used antifungal agents necessitates a search for new agents to control this disease. The in vitro antifungal activities of 27 plant essential oils against two isolates of A. apis (Aksu-4 and Aksu-9 were evaluated. Out of the 27 plant essential oils tested, 21 were found to be effective in killing both isolates of A. apis. Based on their minimum fungicidal concentration (MFC values, the effective oils were grouped into three categories: highly effective, moderately effective and minimally effective. Mountain pepper oil, Kala Bhangra oil, spearmint oil, babuna oil, betel leaf oil, carrot seed oil, cumin seed oil and clove bud oil were highly effective, with MBC values between 50.0 μg/mL and 600.0 μg/mL. Mountain pepper was the most effective essential oil, with an MBC value of 50.0 μg/mL. Citral and caryophyllene containing oils were the most effective with MIC 50 ppm. The essential oils tested exhibited significant antimicrobial activities against both strains of A. apis, and they may contain compounds that could play an important role in the treatment or prevention of Chalkbrood disease of honeybee.

  12. Multiple photoionization following 3d5/2-shell threshold ionization of

    International Nuclear Information System (INIS)

    Matsui, T; Yoshii, H; Tsukamoto, K; Kawakita, S; Murakami, E; Adachi, J; Yagishita, A; Morioka, Y; Hayaishi, T

    2004-01-01

    Multiple photoionization of Xe near the 3d 5/2 -shell threshold photoionization region is studied by threshold electron-ion coincidence spectroscopy. The coincidence spectra of Xe 3+ to Xe 7+ ions exhibit characteristic profiles associated with multi-step post-collision interactions in Auger cascades following 3d 5/2 -shell threshold photoionization. The Auger cascade decay channels leading to the formation of multiply charged ions are deduced from the energies of the profile peaks, which increase gradually with increasing charge state. The formation of Xe 3+ to Xe 5+ ions is found to arise from cascades of normal Auger decays, whereas the formation of Xe 6+ and Xe 7+ ions involves double Auger decays. The branching ratio of double to normal Auger decays is estimated to be 0.25 (±0.1) for the decays following the creation of 3d 5/2 -hole states in Xe

  13. Infra-Population and -Community Dynamics of the Parasites Nosema apis and Nosema ceranae, and Consequences for Honey Bee (Apis mellifera) Hosts

    Science.gov (United States)

    Williams, Geoffrey R.; Shutler, Dave; Burgher-MacLellan, Karen L.; Rogers, Richard E. L.

    2014-01-01

    Nosema spp. fungal gut parasites are among myriad possible explanations for contemporary increased mortality of western honey bees (Apis mellifera, hereafter honey bee) in many regions of the world. Invasive Nosema ceranae is particularly worrisome because some evidence suggests it has greater virulence than its congener N. apis. N. ceranae appears to have recently switched hosts from Asian honey bees (Apis cerana) and now has a nearly global distribution in honey bees, apparently displacing N. apis. We examined parasite reproduction and effects of N. apis, N. ceranae, and mixed Nosema infections on honey bee hosts in laboratory experiments. Both infection intensity and honey bee mortality were significantly greater for N. ceranae than for N. apis or mixed infections; mixed infection resulted in mortality similar to N. apis parasitism and reduced spore intensity, possibly due to inter-specific competition. This is the first long-term laboratory study to demonstrate lethal consequences of N. apis and N. ceranae and mixed Nosema parasitism in honey bees, and suggests that differences in reproduction and intra-host competition may explain apparent heterogeneous exclusion of the historic parasite by the invasive species. PMID:24987989

  14. Infra-population and -community dynamics of the parasites Nosema apis and Nosema ceranae, and consequences for honey bee (Apis mellifera) hosts.

    Science.gov (United States)

    Williams, Geoffrey R; Shutler, Dave; Burgher-MacLellan, Karen L; Rogers, Richard E L

    2014-01-01

    Nosema spp. fungal gut parasites are among myriad possible explanations for contemporary increased mortality of western honey bees (Apis mellifera, hereafter honey bee) in many regions of the world. Invasive Nosema ceranae is particularly worrisome because some evidence suggests it has greater virulence than its congener N. apis. N. ceranae appears to have recently switched hosts from Asian honey bees (Apis cerana) and now has a nearly global distribution in honey bees, apparently displacing N. apis. We examined parasite reproduction and effects of N. apis, N. ceranae, and mixed Nosema infections on honey bee hosts in laboratory experiments. Both infection intensity and honey bee mortality were significantly greater for N. ceranae than for N. apis or mixed infections; mixed infection resulted in mortality similar to N. apis parasitism and reduced spore intensity, possibly due to inter-specific competition. This is the first long-term laboratory study to demonstrate lethal consequences of N. apis and N. ceranae and mixed Nosema parasitism in honey bees, and suggests that differences in reproduction and intra-host competition may explain apparent heterogeneous exclusion of the historic parasite by the invasive species.

  15. Charge and structural ordering in the brownmillerite phases: La1-xSrxMnO2.5 (0.2<x<0.4)

    International Nuclear Information System (INIS)

    Casey, Peter S.; Barker, Daniel; Hayward, Michael A.

    2006-01-01

    The topotactic reduction of La 1-x Sr x MnO 3 (0.2 1-x Sr x MnO 2.5 brownmillerite phases with NaH is described. Neutron and electron diffraction data show the x=0.25 and 0.2 phases adopt structures with an unusual ordered L-R-L-R alternation of twisted chains of Mn(II) tetrahedra within each anion-deficient layer. This is accompanied by Mn(II)/(III) charge ordering within the remaining MnO 6 octahedral layers. In contrast, the x=0.4 phase adopts a structure in which the twisted chains of tetrahedra are disordered

  16. Population Genetics of Nosema apis and Nosema ceranae: One Host (Apis mellifera) and Two Different Histories

    Science.gov (United States)

    Maside, Xulio; Gómez-Moracho, Tamara; Jara, Laura; Martín-Hernández, Raquel; De la Rúa, Pilar; Higes, Mariano; Bartolomé, Carolina

    2015-01-01

    Two microsporidians are known to infect honey bees: Nosema apis and Nosema ceranae. Whereas population genetics data for the latter have been released in the last few years, such information is still missing for N. apis. Here we analyze the patterns of nucleotide polymorphism at three single-copy loci (PTP2, PTP3 and RPB1) in a collection of Apis mellifera isolates from all over the world, naturally infected either with N. apis (N = 22) or N. ceranae (N = 23), to provide new insights into the genetic diversity, demography and evolution of N. apis, as well as to compare them with evidence from N. ceranae. Neutral variation in N. apis and N. ceranae is of the order of 1%. This amount of diversity suggests that there is no substantial differentiation between the genetic content of the two nuclei present in these parasites, and evidence for genetic recombination provides a putative mechanism for the flow of genetic information between chromosomes. The analysis of the frequency spectrum of neutral variants reveals a significant surplus of low frequency variants, particularly in N. ceranae, and suggests that the populations of the two pathogens are not in mutation-drift equilibrium and that they have experienced a population expansion. Most of the variation in both species occurs within honey bee colonies (between 62%-90% of the total genetic variance), although in N. apis there is evidence for differentiation between parasites isolated from distinct A. mellifera lineages (20%-34% of the total variance), specifically between those collected from lineages A and C (or M). This scenario is consistent with a long-term host-parasite relationship and contrasts with the lack of differentiation observed among host-lineages in N. ceranae (mellifera worldwide population is a recent event. PMID:26720131

  17. Effect of CoFe magnetic nanoparticles on the hole transport in poly(2-methoxy, 5-(2-ethylhexiloxy) 1,4-phenylenevinylene)

    International Nuclear Information System (INIS)

    Kumar, Pankaj; Kumar, Hemant; Chand, Suresh; Jain, S C; Kumar, Vikram; Kumar, Vinod; Pant, R P; Tandon, R P

    2008-01-01

    The effect of doping of CoFe magnetic nanoparticles (MNPs) on the hole transport in poly(2-methoxy,5-(2-ethylhexyloxy)-1,4-phenylenevinylene)(MEH-PPV) thin films has been investigated in the temperature range 280-120 K. Hole transport in MEH-PPV is found to be governed by space-charge-limited-conduction (SCLC) with exponential distribution of traps in energy space. Doping of CoFe MNPs in MEH-PPV reduces the hole mobility from 1 x 10 -5 to 6 x 10 -6 cm 2 V -1 s -1 by introducing new trap sites causing their net density increase from 1 x 10 18 to 2.1 x 10 18 cm -3 , which is likely to result in balanced injection and efficient recombination of charge carriers to improve the performance of polymer light emitting diodes

  18. Rab5 regulates internalisation of P2X4 receptors and potentiation by ivermectin.

    Science.gov (United States)

    Stokes, Leanne

    2013-03-01

    The P2X4 receptor is an ATP-gated ion channel expressed in neurons, endothelia and immune cells. Plasma membrane expression of P2X4 is regulated by dynamin-dependent endocytosis, and this study identifies a Rab5-dependent pathway of receptor internalisation. Expression of Rab5 constructs altered the distribution of P2X4 in HEK-293 cells, and both constitutive internalisation and agonist-induced desensitisation of P2X4 were increased by co-expression of wild-type Rab5 or constitutively active Rab5 (Q79L). Expression of inactive dynamin K44A and Rab5 S34N constructs abolished agonist-induced desensitisation, suggesting internalisation as the underlying mechanism. Blocking P2X4 internalisation in this way also abolished potentiation of ATP-induced currents by the allosteric modulator ivermectin. This suggests that the dynamin-Rab5 internalisation pathway is essential for the ivermectin potentiation effect. In agreement with this hypothesis, the co-expression of wild-type dynamin, wild-type Rab5 or active Rab5 (Q79L) could increase the potentiation of the ATP-induced P2X4 response by ivermectin. These findings highlight Rab5 GTPase as a key regulator of P2X4 receptor cell surface expression and internalisation.

  19. Characterisation of Al{sub 0.52}In{sub 0.48}P mesa p-i-n photodiodes for X-ray photon counting spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Butera, S., E-mail: S.Butera@sussex.ac.uk; Lioliou, G.; Barnett, A. M. [Semiconductor Materials and Device Laboratory, School of Engineering and Informatics, University of Sussex, Brighton BN1 9QT (United Kingdom); Krysa, A. B. [EPSRC National Centre for III-V Technologies, University of Sheffield, Mappin Street, Sheffield S1 3JD (United Kingdom)

    2016-07-14

    Results characterising the performance of thin (2 μm i-layer) Al{sub 0.52}In{sub 0.48}P p{sup +}-i-n{sup +} mesa photodiodes for X-ray photon counting spectroscopy are reported at room temperature. Two 200 μm diameter and two 400 μm diameter Al{sub 0.52}In{sub 0.48}P p{sup +}-i-n{sup +} mesa photodiodes were studied. Dark current results as a function of applied reverse bias are shown; dark current densities <3 nA/cm{sup 2} were observed at 30 V (150 kV/cm) for all the devices analysed. Capacitance measurements as a function of applied reverse bias are also reported. X-ray spectra were collected using 10 μs shaping time, with the device illuminated by an {sup 55}Fe radioisotope X-ray source. Experimental results showed that the best energy resolution (FWHM) achieved at 5.9 keV was 930 eV for the 200 μm Al{sub 0.52}In{sub 0.48}P diameter devices, when reverse biased at 15 V. System noise analysis was also carried out, and the different noise contributions were computed.

  20. Web API Growing Pains : Loosely Coupled yet Strongly Tied

    NARCIS (Netherlands)

    Espinha, T.; Zaidman, A.; Gross, H.G.

    2014-01-01

    Web APIs provide a systematic and extensible approach for application-toapplication interaction. Developers using web APIs are forced to accompany the API providers in their software evolution tasks. In order to understand the distress caused by this imposition on web API client developers we

  1. Continuous API-crystal coating via coacervation in a tubular reactor.

    Science.gov (United States)

    Besenhard, M O; Thurnberger, A; Hohl, R; Faulhammer, E; Rattenberger, J; Khinast, J G

    2014-11-20

    We present a proof-of-concept study of a continuous coating process of single API crystals in a tubular reactor using coacervation as a microencapsulation technique. Continuous API crystal coating can have several advantages, as in a single step (following crystallization) individual crystals can be prepared with a functional coating, either to change the release behavior, to protect the API from gastric juice or to modify the surface energetics of the API (i.e., to tailor the hydrophobic/hydrophilic characteristics, flowability or agglomeration tendency, etc.). The coating process was developed for the microencapsulation of a lipophilic core material (ibuprofen crystals of 20 μm- to 100 μm-size), with either hypromellose phthalate (HPMCP) or Eudragit L100-55. The core material was suspended in an aqueous solution containing one of these enteric polymers, fed into the tubing and mixed continuously with a sodium sulfate solution as an antisolvent to induce coacervation. A subsequent temperature treatment was applied to optimize the microencapsulation of crystals via the polymer-rich coacervate phase. Cross-linking of the coating shell was achieved by mixing the processed material with an acidic solution (pH<3). Flow rates, temperature profiles and polymer-to-antisolvent ratios had to be tightly controlled to avoid excessive aggregation, leading to pipe plugging. This work demonstrates the potential of a tubular reactor design for continuous coating applications and is the basis for future work, combining continuous crystallization and coating. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. The ΓX-L/LEdd relation in BAT AGN Spectroscopic Survey (BASS)

    Science.gov (United States)

    Trakhtenbrot, Benny; Ricci, Claudio; Koss, Michael; Schawinski, Kevin; Mushotzky, Richard; Ueda, Yoshihiro; Veilleux, Sylvain; Lamperti, Isabella; Oh, Kyuseok; Treister, Ezequiel; Stern, Daniel; Harrison, Fiona; Balokovic, Mislav

    2018-01-01

    We present a study of the relation between accretion rate (in terms of L/LEdd) and shape of the hard X-ray spectral energy distribution (namely the photon index Γx) for a large sample of over 200 hard X-ray-selected, low-redshift active galactic nuclei (AGNs), drawn from the Swift/BAT AGN Spectroscopic Survey (BASS). This includes 30 AGNs for which black hole mass (and therefore L/LEdd) is measured directly through masers, spatially resolved gas or stellar dynamics, or reverberation mapping. The high-quality and broad energy coverage of the data provided through BASS allow us to examine several alternative determinations of both Γx and L/LEdd. We find very weak correlation between Γx and L/LEdd for the BASS sample as a whole, with best-fitting relations that are considerably shallower than those reported in previous studies. Moreover, we find no corresponding correlations among the subsets of AGN with different MBH determination methodology, and in particular those AGN with direct or single-epoch MBH estimates. This latter finding is in contrast to several previous studies which focused on z > 0.5 broad-line AGN. We conclude that this tension can be partially accounted for if one adopts a simplified, power-law X-ray spectral model, combined with L/LEdd estimates that are based on the continuum emission and on single-epoch broad-line spectroscopy in the optical regime. Given these findings, we highlight the limitations of using Γx as a probe of supermassive black hole evolution in deep extragalactic X-ray surveys.

  3. Jobs API

    Data.gov (United States)

    General Services Administration — This Jobs API returns job openings across the federal government and includes all current openings posted on USAJobs.gov that are open to the public and located in...

  4. Vida a la fatiga de juntas soldadas del acero inoxidable AISI 316L obtenidas mediante el proceso GMAW

    Directory of Open Access Journals (Sweden)

    Puchi-Cabrera, E. S.

    2007-06-01

    Full Text Available An investigation has been conducted in order to determine the effect of both the metallic transfer mode (pulsed arc or short circuit and the O2 content in the Ar/O2 gas mixture, of the gas-metal arc welding process (GMAW, on the fatigue life under uniaxial conditions of welded joints of 316L stainless steel. It has been concluded that the mixture of the protective gases employed in the process could have an important influence on the fatigue life of the welded joints of such steel in two different ways. Firstly, through the modification of the radius of curvature at the joint between the welding toe and the base metal and, secondly, through a more pronounced degree of oxidation of the alloying elements induced by a higher O2 content in the mixture. As far as the metallic transfer mode is concerned, it has been determined that the welded joints obtained under a pulsed arc mode show a greater fatigue life in comparison with the joints obtained under short circuit for both gas mixtures.

    Se ha llevado a cabo una investigación con la finalidad de determinar el efecto, tanto del modo de transferencia metálica (arco pulsado o cortocircuito como del contenido de O2 en la mezcla de gases protectores Ar/O2, del proceso de soldadura a tope mediante arco metálico con protección gaseosa (GMAW, sobre la vida a la fatiga en condiciones uniaxiales de juntas soldadas del acero inoxidable AISI 316L. Dicho trabajo ha permitido concluir que la composición de la mezcla de gases protectores del proceso GMAW pudiera tener una influencia importante en la vida a la fatiga de las juntas soldadas de dicho material, a través de dos formas distintas: primero, mediante la modificación del radio de curvatura entre la raíz del cordón de soldadura y el metal base y, en segundo lugar, a través del mayor grado de oxidación de los elementos de aleación. En cuanto al modo de transferencia metálica, se determinó que las juntas soldadas mediante arco pulsado

  5. Oxidación a alta temperatura de un acero ASTM A335 P92 en contacto con una mezcla de sales de

    OpenAIRE

    Jessica Rodríguez Pérez; Eduardo Santos Sánchez; Darío Yesid Peña Ballesteros; Anderson Sandoval Amador; Hugo Armando Estupiñán Durán

    2016-01-01

    En esta investigación se evaluó la oxidación del acero ASTM A335 P92 en una mezcla de sales 40% K2SO4 - 60% NaCl a temperaturas de 500ºC a 700ºC, a intervalos de 50°C con tiempos de exposición de 1, 3, 10, 30, 100 y 150 horas, utilizando la norma estandarizada por la Federación Europea de Corrosión. Se realizó análisis metalográfico y de dureza antes y después del ensayo para identificar el posible cambio estructural; se realizan pruebas de difracción de rayos X (DRX), microscopía electrónica...

  6. Comportamiento del acero de baja aleación SA-508 y del acero al carbono A-410b en las condiciones de operación y parada del circuito primario de los reactores de agua ligera tipo PWR

    Directory of Open Access Journals (Sweden)

    García-Redondo, María del Sol

    2000-04-01

    Full Text Available The corrosion rate of low alloy steel SA-508 and carbon steel A-410b in simulated operation and shutdown conditions of pressurized water reactor has been determined. Moreover potentiodynamic polarization curves and galvanic effect through coupling of AISI-304 have been carried out under shutdown simulated condition.

    En este trabajo se ha determinado la cinética de corrosión del acero de baja aleación SA-508 y del acero al carbono A-410b en condiciones que simulan la operación y la parada de los reactores de agua ligera a presión. También se han realizado curvas de polarización potenciodinámica y se ha estudiado el acoplamiento galvánico con AISI-304 en condiciones de parada de los reactores de agua ligera a presión.

  7. Recalls API

    Data.gov (United States)

    General Services Administration — This Recalls API allows you to tap into a list of (1) drug and food safety recalls from the Food and Drug Administration, Food Safety and Inspection Service, and...

  8. GEL DE ALOE-VERA COMO POTENCIAL INHIBIDOR DE LA CORROSIÓN DEL ACERO DE REFUERZO ESTRUCTURAL

    Directory of Open Access Journals (Sweden)

    Héctor Herrera-Hernández

    2015-01-01

    Full Text Available En el presente trabajo se estudiaelectroquímicamente un GELextracto de las hojas de ALOE VERAcomo un posible inhibidor de la corrosión del acero de refuerzo estructuraldel concreto.Los estudiosde corrosiónse llevaron a cabo en 1M de HCl y utilizando la técnica de espectroscopia de impedancia electroquímica (EISse evaluó la resistencia a la corrosión en presencia y ausencia del GEL.Los diagramas de impedancia mostraronque la adición en diferentes proporcionesdel GELinhibe notablemente el proceso de la corrosión del acero inmerso en la solución ácida. También se determinó que las moléculas del GEL obedecena un mecanismo de fisisorciónsobre la superficie del metal de acuerdo con el modelo de isoterma de Langmuircon unG°adsde alrededor de 14.17 kJ/mol. El GEL se clasificócomo un inhibidor orgánico del tipo mixto.

  9. Influencia de la termodependencia de las propiedades físicas del acero en la simulación por elementos finitos del proceso de soldadura

    Directory of Open Access Journals (Sweden)

    Félix Ramos Morales

    2009-01-01

    Full Text Available En el presente trabajo se desarrolló un modelo de elementos finitos para simular la unión a tope, con electrodo E 7018 de 3,2 mm de diámetro, de dos placas de acero con bajo contenido de carbono y baja aleación. Adicionalmente, se estudia la influencia sobre la distribución de temperaturas en la placa al considerar la termo-dependencia de diferentes propiedades físicas del acero (conductividad térmica y calor específico.

  10. Soldadura de aceros dual phase en chapa fina: GMAW, PAW y RSW

    OpenAIRE

    Svoboda,Hernán; Lorusso,Hernán N.; Burgueño,Alejandro

    2011-01-01

    Los aceros Dual Phase (DP) han encontrado recientemente una fuerte aplicación en elementos estructurales en la industria automotriz, debido a la necesidad de disminuir peso. La soldadura de estos materiales cobra particular importancia considerando su aplicación estructural y los procesos relacionados en su fabricación. En particular la soldadura de resistencia por punto (RSW) y semiautomática con alambre macizo y protección gaseosa (GMAW) son ampliamente utilizados en la industria automotriz...

  11. Generation of baryon excess in SUsub(L)(2) x SUsub(R)(2) x SUsub(c)(4)

    International Nuclear Information System (INIS)

    Deo, B.B.; Prasad, V.B.

    1980-08-01

    We have calculated the magnitude of the cosmological baryon asymmetry in a gauge theory based on the group SUsub(L)(2) x SUsub(R)(2) x SUsub(c)(4) and find that plausible parameters exist in the model to explain the baryon excess with a subunifying mass scale of 10 4 -10 5 GeV. The novel idea used is that the vacuum eats away antimatter through the VEV of the Higgs meson. (author)

  12. Conformado por vía coloidal de recubrimientos en la cara interna de un tubo de acero

    Directory of Open Access Journals (Sweden)

    Ferrari, B.

    2004-04-01

    Full Text Available The development of new coating processes has important limitations related to the films thickness and the geometry of the coating substrates. In this work, two colloidal forming processes are proposed for manufacturing ceramic and metallic coatings on the inner surface of a steel pipe. Ceramic coatings of CaCO3 have been formed by electrophoretic deposition (EPD. Aqueous stable suspensions were prepared and a electrophoretic cell was designed, in which the steel tube to be coated acted simultaneously as container and working electrode. Nickel films were prepared by filling the pipe with the suspension and rotating to fully wet the steel surface. Nickel suspensions were formulated focusing an improved wettability and adherence to the steel surface by using binders. From these processes, ceramic and metallic coatings with 300- 350 μm in thickness, homogeneous and strongly adhered to the inner surface of the steel pipe have been obtained.

    El desarrollo de las tecnologías de fabricación de recubrimientos presenta importantes limitaciones relativas a los espesores de las capas fabricadas y a la geometría de los substratos a recubrir. En este trabajo se proponen dos procesos de conformado coloidal de revestimientos cerámicos y metálicos en la cara interna de un tubo de acero. El revestimiento cerámico (CaCO3 se ha conformado por deposición electroforética (EPD. Para ello se han preparado suspensiones estables de CaCO3 en agua, y se ha diseñado una célula electroforética en la que el tubo es a la vez el contenedor y el electrodo de trabajo. El revestimiento metálico (níquel se ha fabricado por vertido de una suspensión estable sobre el propio tubo de acero. Para ello se han acondicionado las suspensiones con el objetivo de mejorar el mojado y la adherencia sobre el acero. A partir de los procesos de EPD y vertido se han obtenido revestimientos cerámicos y metálicos, respectivamente, con espesores de 300-350 μm, homogéneos y

  13. 3.5 keV X-ray line signal from dark matter decay in local U(1){sub B−L} extension of Zee-Babu model

    Energy Technology Data Exchange (ETDEWEB)

    Baek, Seungwon [School of Physics and Open KIAS Center, KIAS,85 Hoegiro Dongdaemun-gu, Seoul 130-722 (Korea, Republic of)

    2015-08-06

    We consider a local U(1){sub B−L} extension of Zee-Babu model to explain the recently observed 3.5 keV X-ray line signal. The model has three Standard model (SM)-singlet Dirac fermions with different U(1){sub B−L} charges. A complex scalar field charged under U(1){sub B−L} is introduced to break the U(1){sub B−L} symmetry. After U(1){sub B−L} symmetry breaking a remnant discrete symmetry stabilizes the lightest state of the Dirac fermions, which can be a stable dark matter (DM). The second lightest state, if mass splitting with the stable DM is about 3.5 keV, decays dominantly to the stable DM and 3.5 keV photon through two-loop diagrams, explaining the X-ray line signal. Two-loop suppression of the decay amplitude makes its lifetime much longer than the age of the universe and it can be a decaying DM candidate in large parameter region. We also introduce a real scalar field which is singlet under both the SM and U(1){sub B−L} and can explain the current relic abundance of the Dirac fermionic DMs. If the mixing with the SM Higgs boson is small, it does not contribute to DM direct detection. The main contribution to the scattering of DM off atomic nuclei comes from the exchange of U(1){sub B−L} gauge boson, Z{sup ′}, and is suppressed below current experimental bound when Z{sup ′} mass is heavy (≳10 TeV). If the singlet scalar mass is about 0.1–10 MeV, DM self-interaction can be large enough to solve small scale structure problems in simulations with the cold DM, such as, the core-vs-cusp problem and too-big-to-fail problem.

  14. Beyond 9-ODA: sex pheromone communication in the European honey bee Apis mellifera L.

    Science.gov (United States)

    Brockmann, Axel; Dietz, Daniel; Spaethe, Johannes; Tautz, Jürgen

    2006-03-01

    The major component of the mandibular gland secretion of queen honeybees (Apis mellifera L.), 9-ODA ((2E)-9-oxodecenoic acid), has been known for more than 40 yr to function as a long-range sex pheromone, attracting drones at congregation areas and drone flyways. Tests of other mandibular gland components failed to demonstrate attraction. It remained unclear whether these components served any function in mating behavior. We performed dual-choice experiments, using a rotating drone carousel, to test the attractiveness of 9-ODA compared to mixtures of 9-ODA with three other most abundant components in virgin queen mandibular gland secretions: (2E)-9-hydroxydecenoic acid (9-HDA), (2E)-10-hydroxydecenoic acid (10-HDA), and p-hydroxybenzoate (HOB). We found no differences in the number of drones attracted to 9-ODA or the respective mixtures over a distance. However, adding 9-HDA and 10-HDA, or 9-HDA, 10-HDA, and HOB to 9-ODA increased the number of drones making contact with the baited dummy. On the basis of these results, we suggest that at least 9-HDA and 10-HDA are additional components of the sex pheromone blend of A. mellifera.

  15. Hydrogen sorption properties of the Lasub(1-x)Casub(x)Ni5 and La(Nisub(1-x)Cusub(x))5 systems

    International Nuclear Information System (INIS)

    Shinar, J.; Shaltiel, D.; Davidov, D.; Grayevsky, A.

    1978-01-01

    The hydrogen sorption properties of the Lasub(1-x)Casub(x)Ni 5 and La(Nisub(1-x)Cusub(x)) 5 systems were investigated at various temperatures and at pressures up to 20 atm. It was found that initial substitution of La by Ca in LaNi 5 caused an increase in the hydrogen dissociation pressure, up to Casub(0.3)Lasub(0.7)Ni 5 . In the Casub(0.3)Lasub(0.7)Ni 5 -CaNi 5 range, the dissociation pressure decreased. The absorption capacity of CaNi 5 was dependent on the purity of the sample and increased significantly at low temperatures. The stability of La(Nisub(1-x)Cusub(x)) 5 hydrides increased linearly from LaNi 5 to LaCu 5 . These features are discussed in the light of existing models of ternary and pseudoternary hydride stability. Finally, the role of the measured change in entropy ΔS in determining the occupied interstitial sites in the hydride is outlined and discussed in relation to these systems. (Auth.)

  16. Improving the API dissolution rate during pharmaceutical hot-melt extrusion I: Effect of the API particle size, and the co-rotating, twin-screw extruder screw configuration on the API dissolution rate.

    Science.gov (United States)

    Li, Meng; Gogos, Costas G; Ioannidis, Nicolas

    2015-01-15

    The dissolution rate of the active pharmaceutical ingredients in pharmaceutical hot-melt extrusion is the most critical elementary step during the extrusion of amorphous solid solutions - total dissolution has to be achieved within the short residence time in the extruder. Dissolution and dissolution rates are affected by process, material and equipment variables. In this work, we examine the effect of one of the material variables and one of the equipment variables, namely, the API particle size and extruder screw configuration on the API dissolution rate, in a co-rotating, twin-screw extruder. By rapidly removing the extruder screws from the barrel after achieving a steady state, we collected samples along the length of the extruder screws that were characterized by polarized optical microscopy (POM) and differential scanning calorimetry (DSC) to determine the amount of undissolved API. Analyses of samples indicate that reduction of particle size of the API and appropriate selection of screw design can markedly improve the dissolution rate of the API during extrusion. In addition, angle of repose measurements and light microscopy images show that the reduction of particle size of the API can improve the flowability of the physical mixture feed and the adhesiveness between its components, respectively, through dry coating of the polymer particles by the API particles. Copyright © 2014. Published by Elsevier B.V.

  17. Decapado de un acero inoxidable austenítico mediante mezclas ecológicas basadas en H2O2 - H2SO4 - iones F-

    Directory of Open Access Journals (Sweden)

    Narváez, L.

    2013-04-01

    Full Text Available This study reports the pickling of 316L stainless steel using mixtures of hydrogen peroxide (H2O2, sulphuric acid (H2SO4 and fluoride ions as hydrofluoric acid (HF, sodium fluoride (NaF and potassium fluoride (KF. The decomposition of H2O2 in the mixtures was assessed at different temperatures 25 °C to 60 °C, with ferric ion contents from 0 to 40 g/l. According to the results obtained, were established the optimal condition pickling at 20 g/l of ferric ions, 25 °C and p-toluensulphonic acid as stabilizer of H2O2. The HF pickling mixture was the only capable to remove totally the oxide layer from the 316L stainless steel after 300 s. The fluoride salts pickling mixtures only remove partially the oxide layer (20 to 40 % aprox. after 300 s. When the pickling time was increased until 1200 s, the removal percentages were around to 80 %.En este estudio se presenta el decapado del acero inoxidable austenítico 316L utilizando mezclas de peróxido de hidrógeno (H2O2/ácido sulfúrico (H2SO4/iones fluoruro; los iones fluoruro provienen del ácido fluorhídrico (HF, fluoruro de sodio (NaF y fluoruro de potasio (KF. La estabilidad del H2O2 fue valorada modificando las concentraciones del ión férrico de 0 a 40 g/l y las temperaturas de 25 °C a 60 °C en las mezclas decapantes. Se establecieron las condiciones óptimas de decapado utilizando 20 g/l de iones férrico a 25 °C empleando el ácido p-toluensulfónico como estabilizante del H2O2. La mezcla que contenía HF fue la única capaz de eliminar completamente los óxidos superficiales del acero a tiempos de 300 s. Las mezclas a base de sales fluoradas eliminaron parcialmente los óxidos (20 y 40 % aprox. en 300 s. Al incrementar el tiempo de decapado hasta 1200 s se obtuvieron porcentajes de eliminación alrededor de un 80 %.

  18. Benefits and Pitfalls of Using HTML5 APIs for Online Experiments and Simulations

    Directory of Open Access Journals (Sweden)

    Pablo Garaizar

    2012-11-01

    Full Text Available The most recent advances in the architecture of the Web allow using it as an excellent platform to deliver experiments and simulations over the Internet. However, there are still some challenges related to the animations’ accuracy, to user input collection or to real-time communications that have to be accomplished to properly port native application- based experiments and simulations to the Web. The limitations of the standards preceding HTML5 have forced web developers to embed non-HTML objects using a wide range of non-standard plugins and causing an extremely fragmented execution environment where features must be implemented several times in different programming languages to guarantee full compliance with every user-agent. As HTML5 provides a standard -yet fully-featured- environment to develop and execute applications, web user-agents are now more similar to application players than to simple Internet browsers. In this paper we analyze the benefits and pitfalls of these new Application Programming Interfaces (APIs, providing examples of both good and bad instances of research-related use.

  19. fine-GRAPE : Fine-grained APi usage extractor – an approach and dataset to investigate API usage

    NARCIS (Netherlands)

    Sawant, A.A.; Bacchelli, A.

    An Application Programming Interface (API) provides a set of functionalities to a developer with the aim of enabling reuse. APIs have been investigated from different angles such as popularity usage and evolution to get a better understanding of their various characteristics. For such studies,

  20. Effects of Nosema apis, N. ceranae, and coinfections on honey bee (Apis mellifera) learning and memory.

    Science.gov (United States)

    Charbonneau, Lise R; Hillier, Neil Kirk; Rogers, Richard E L; Williams, Geoffrey R; Shutler, Dave

    2016-03-10

    Western honey bees (Apis mellifera) face an increasing number of challenges that in recent years have led to significant economic effects on apiculture, with attendant consequences for agriculture. Nosemosis is a fungal infection of honey bees caused by either Nosema apis or N. ceranae. The putative greater virulence of N. ceranae has spurred interest in understanding how it differs from N. apis. Little is known of effects of N. apis or N. ceranae on honey bee learning and memory. Following a Pavlovian model that relies on the proboscis extension reflex, we compared acquisition learning and long-term memory recall of uninfected (control) honey bees versus those inoculated with N. apis, N. ceranae, or both. We also tested whether spore intensity was associated with variation in learning and memory. Neither learning nor memory differed among treatments. There was no evidence of a relationship between spore intensity and learning, and only limited evidence of a negative effect on memory; this occurred only in the co-inoculation treatment. Our results suggest that if Nosema spp. are contributing to unusually high colony losses in recent years, the mechanism by which they may affect honey bees is probably not related to effects on learning or memory, at least as assessed by the proboscis extension reflex.

  1. Effects of sulphide ion on the corrosion behaviour of X52 steel in a carbon dioxide environment at temperature 40 deg. C

    International Nuclear Information System (INIS)

    Fatah, M.C.; Ismail, M.C.; Ari-Wahjoedi, B.; Kurnia, K.A.

    2011-01-01

    Research highlights: → We study the effect of sulphide ion on the corrosion behaviour of X52 steel. → Increasing sulphide ion concentration will increase the corrosion rate of X52 steel. → Increasing sulphide ion concentration will increase cathodic reaction. → Less protective film, also contribute to the increasing the corrosion rate. - Abstract: The electrochemical behaviour of X52 steel in the presence of sulphide at 40 deg. C in a CO 2 environment was investigated using the methods of linear polarization resistance (LPR), potentiodynamic sweep, electrochemical impedance spectroscopy (EIS). In addition, the surface of X52 steel was also studied using scanning electron microscopy (SEM). The results showed that the corrosion rate of X52 steel increased with increasing concentration of sulphide ion. Potentiodynamic curve showed that there were changes in cathodic branch due to the change in the nature of cathodic reaction in the presence of sulphide ion. EIS analysis showed the higher sulphide ion concentration, the higher adsorbed species on the steel surface that contributed in the cathodic reaction. Furthermore, SEM results showed crevices on the scale which indicated pitting tendency in sulphide ion solutions. The less protective film, probably mackinawite, also contributed to the increase of corrosion rate in the presence of sulphide ion.

  2. Tetraploidy enhances boron-excess tolerance in Carrizo Citrange (Citrus sinensis L. Osb. x Poncirus trifoliata L. Raf.

    Directory of Open Access Journals (Sweden)

    Marta eRuiz

    2016-05-01

    Full Text Available Tetraploidy modifies root anatomy which may lead to differentiated capacity to uptake and transport mineral elements. This work provides insights into physiological and molecular characters involved in boron (B toxicity responses in diploid (2x and tetraploid (4x plants of Carrizo citrange (Citrus sinensis L. Osb. x Poncirus trifoliata L. Raf., a widely used citrus rootstock. With B excess, 2x plants accumulated more B in leaves than 4x plants, which accounted for their higher B uptake and root-to-shoot transport rates. Ploidy did not modify the expression of membrane transporters NIP5 and BOR1 in roots. The cellular allocation of B excess differed between ploidy levels in the soluble fraction, which was lower in 4x leaves, while cell wall-linked B was similar in 2x and 4x genotypes. This correlates with the increased damage and stunted growth recorded in the 2x plants. The 4x roots were found to have fewer root tips, shorter specific root length, longer diameter, thicker exodermis and earlier tissue maturation in root tips, where the Casparian strip was detected at a shorter distance from the root apex than in the 2x roots. The results presented herein suggest that the root anatomical characters of the 4x plants play a key role in their lower B uptake capacity and root-to-shoot transport.

  3. High-pressure X-ray diffraction of L-ALANINE crystal

    DEFF Research Database (Denmark)

    Olsen, J.S.; Gerward, Leif; Souza, A.G.

    2006-01-01

    L-ALANINE has been studied by X-ray diffraction at ambient temperature and pressure up to 10.3 GPa. The material is found to transform to a tetragonal structure between 2 and 3 GPa. and to a monoclinic structure between 8 and 10 GPa. The experimental bulk modulus is 25(5) GPa for the orthorhombic...

  4. Investigation of a 0.52 eV absorption band of n-type Ge1-xSix solid solutions irradiated with fast electrons at 77 K

    International Nuclear Information System (INIS)

    Abbasov, Sh.M.; Allakhverdiev, K.R.; Agaverdieva, G.T.; Bakhyshov, N.A.; Nagiev, A.I.

    1987-01-01

    Solid solutions belonging to the Ge 1-x Si x system are among the promising semiconductor materials. There is no published information on the absorption band in the region of 0.52 eV in Ge 1-x Si x solid solutions irradiated with fast electrons. The authors determined the infrared absorption spectra, impurity photoconductivity, and Hall effect of n-type Ge 1-x Si x solid solutions doped with antimony. These solid solutions were irradiated at 77 K with 5 MeV electrons in doses up to 2 x 10 17 cm -2 . This irradiation was carried out by a method described in Ref. 3

  5. Corrosion behavior of API 5L-X80 Pipeline steel for natural gas pipeline

    International Nuclear Information System (INIS)

    Mohd Asyadi Azam Mohd Abid; Imai, Hachiro

    2007-01-01

    Natural energy problem, including the environmental aspects had changes into certain circumstances in recent years and natural gas has been a focus of constant attention from the viewpoint of energy efficiency and pollution free. From that kind of background, pipeline construction for petroleum and natural gas were considerate as energy infrastructure maintenance plan. Based on the clarification of Asian Pipeline Project (1997-2007) centered in Japan, international pipeline is needed as the natural gas is mainly transported from gas field in Russia and Middle East to consumer country such as Japan etc. It used in severe condition such as cold district and sea. In the meantime, pipeline steel is not just received damages by earth crust fluctuation and corrosion, but also suffered from the corrosion caused by anions that were dissolved in sea and groundwater. The diversification of dispersion and consumption structure of natural gas supply acceptance base are seen regarding, that made the needs of the storing are rising and dealt with the quantitative spatial expansion of the demand. By that, corrosion resistance, not only the hardness, tough, weldability, corrosiveness gas environment is extremely required. (author)

  6. Evaluación experimental de la resistencia a la corrosión de un acero aisi-sae 4140 implantado con iones de nitrógeno

    OpenAIRE

    PEÑA, DARIO; FONTALVO, PAOLA; ESTUPIÑAN, HUGO; NIÑO, DANNIER; VESGA, WILSON

    2010-01-01

    Se estudió la resistencia a la corrosión de un acero AISI-SAE 4140 implantado con iones de Nitrógeno mediante la técnica 3DII (Implantación Iónica Tridimensional). Se evaluaron diferentes rugosidades de las muestras implantadas mediante técnicas electroquímicas de Rp, EIS y Tafel en una salmuera al 3% de NaCl, donde se obtuvo la mayor resistencia a la corrosión para el material implantado con menor rugosidad. Se produjo la formación de una posible capa protectora estable con la inmersión de l...

  7. Development of an in-line Raman spectroscopic method for continuous API quantification during twin-screw wet granulation.

    Science.gov (United States)

    Harting, Julia; Kleinebudde, Peter

    2018-04-01

    Raman spectroscopy was evaluated as a process analytical technology (PAT) tool for continuous API quantification during twin-screw wet granulation. Therefore, a Raman probe was implemented in front of the granulator barrel. This setup enabled the collection of Raman spectra upon a constant granule flow. To develop an in-line PLS calibration model, eight binary mixtures of the API and lactose monohydrate with API contents between 5 and 50% were pre-blended and granulated in a twin-screw granulator with a screw speed of 150 rpm and a powder feed rate of 40 g/min. Water was used as a granulation liquid with different liquid to solid ratios depending on the API content. Ibuprofen and diclofenac sodium were chosen as model drugs and separated PLS models were built for each API. The predictive performance of the developed PLS models was determined by granulating and monitoring new test samples containing different API concentrations. This evaluation showed that the models were able to predict the API concentration with an RMSEP of 0.59% for ibuprofen and 1.5% for diclofenac sodium. In a second part, the developed in-line Raman spectroscopic method was used to determine the API concentration during a split feeding process. Therefore, the API and lactose monohydrate were added by two independently adjustable feeders into the twin-screw granulator barrel. The in-line spectroscopy analysis which was verified by UV-analysis indicated that the mixing ability of the twin-screw granulator was good for the used settings and all adjusted API concentrations. Copyright © 2018 Elsevier B.V. All rights reserved.

  8. Evaluación del trabajo esencial de fractura en chapa de un acero de alta resistencia de fase dual

    Directory of Open Access Journals (Sweden)

    Gutiérrez, D.

    2013-02-01

    Full Text Available Fracture toughness of advanced high strength steels (AHSS, can be used to optimize crash behavior of structural components. However it cannot be readily measured in metal sheet because of the sheet thickness. In this work, the Essential Work of Fracture (EWF methodology is proposed to evaluate the fracture toughness of metal sheets. It has been successfully applied in polymers films and some metal sheets. However, their information about the applicability of this methodology to AHSS is relatively scarce. In the present work the fracture toughness of a Dual Phase (strength of 800 MPa and drawing steel sheets has been measured by means of the EWF. The results show that the test requirements are met and also show the clear influence of notch radii on the measured values, specially for the AHSS grade. Thus, the EWF is postulated as a methodology to evaluate the fracture toughness in AHSS sheets.

    La tenacidad de fractura de aceros de alta resistencia (AHSS, es una propiedad interesante para optimizar el comportamiento a impacto, pero su caracterización experimental en chapas metálicas es compleja debido a su espesor. En este trabajo se plantea el método del Trabajo Esencial de Fractura (TEF, como alternativa al cálculo de la tenacidad. Este método ya ha sido utilizado con éxito en polímeros y aceros dúctiles, aunque la información sobre su aplicación en AHSS es escasa. Se ha evaluado la tenacidad en un acero de fase dual de 800 MPa de resistencia y se ha comparado con la de un acero de embutición. Los resultados muestran que se cumplen los requisitos del método y ponen en evidencia la influencia del radio de entalla en el valor obtenido de TEF, especialmente para AHSS. Con todo ello, el método TEF se puede usar para caracterizar la tenacidad de AHSS en formato chapa.

  9. Studi Eksperimen Distribusi Temperatur Nyala Api Kompor Bioetanol Tipe Side Burner dengan Variasi Diameter Firewall

    Directory of Open Access Journals (Sweden)

    R.R. Vienna Sona Saputri Soetadi

    2012-09-01

    Full Text Available Untuk mendapatkan kompor bioetanol efisiensi thermal maksimal diperlukan penelitian komprehensif. Salah satunya adalah penelitian terhadap posisi peletakkan beban pada kompor bioetanol kompak. Pengujian dilakukan pada kompor uji bioetanol dengan kadar 99%, yaitu kompor bioetanol tipe side burner dengan firewall 2.5 inci dan firewall 3 inci. Pengukuran temperatur api dengan 13 thermocouple K dengan pengukuran searah api keatas setiap 5 mm-an. Kemudian, water boiling test dilakukan untuk mendapatkan daya dan beban dan dilanjutkan mengukur waktu pendidihan air. Hasil penelitian ini menunjukkan gambaran total distribusi temperatur nyala api difusi. Hasil menunjukkan untuk kompor 2.5 inci dengan daya 1.6 kW mempunyai temperatur 542 ºC dengan jarak ketinggian 5 mm dari rim kompor sedangkan kompor 3 inci menghasilkan daya 2.38 kW dengan temperatur 516 ºC.

  10. OSCAR API for Real-Time Low-Power Multicores and Its Performance on Multicores and SMP Servers

    Science.gov (United States)

    Kimura, Keiji; Mase, Masayoshi; Mikami, Hiroki; Miyamoto, Takamichi; Shirako, Jun; Kasahara, Hironori

    OSCAR (Optimally Scheduled Advanced Multiprocessor) API has been designed for real-time embedded low-power multicores to generate parallel programs for various multicores from different vendors by using the OSCAR parallelizing compiler. The OSCAR API has been developed by Waseda University in collaboration with Fujitsu Laboratory, Hitachi, NEC, Panasonic, Renesas Technology, and Toshiba in an METI/NEDO project entitled "Multicore Technology for Realtime Consumer Electronics." By using the OSCAR API as an interface between the OSCAR compiler and backend compilers, the OSCAR compiler enables hierarchical multigrain parallel processing with memory optimization under capacity restriction for cache memory, local memory, distributed shared memory, and on-chip/off-chip shared memory; data transfer using a DMA controller; and power reduction control using DVFS (Dynamic Voltage and Frequency Scaling), clock gating, and power gating for various embedded multicores. In addition, a parallelized program automatically generated by the OSCAR compiler with OSCAR API can be compiled by the ordinary OpenMP compilers since the OSCAR API is designed on a subset of the OpenMP. This paper describes the OSCAR API and its compatibility with the OSCAR compiler by showing code examples. Performance evaluations of the OSCAR compiler and the OSCAR API are carried out using an IBM Power5+ workstation, an IBM Power6 high-end SMP server, and a newly developed consumer electronics multicore chip RP2 by Renesas, Hitachi and Waseda. From the results of scalability evaluation, it is found that on an average, the OSCAR compiler with the OSCAR API can exploit 5.8 times speedup over the sequential execution on the Power5+ workstation with eight cores and 2.9 times speedup on RP2 with four cores, respectively. In addition, the OSCAR compiler can accelerate an IBM XL Fortran compiler up to 3.3 times on the Power6 SMP server. Due to low-power optimization on RP2, the OSCAR compiler with the OSCAR API

  11. Registro de Nephridiophaga sp. (Protista: Nephridiophagidae en Apis mellifera (Hymenoptera: Apidae del Sur de la región Pampeana Record of Nephridiophaga sp. (Protista: Nephridiophagidae in Apis mellifera (Hymenoptera: Apidae of the southern Pampas

    Directory of Open Access Journals (Sweden)

    Santiago Plischuk

    2011-12-01

    Full Text Available Durante estudios prospectivos tendientes a la detección de protistas asociados a ápidos en la región Pampeana, se observó la presencia de esporos ovales bicóncavos y grupos de esporos (cúmulos en los túbulos de Malpighi de abejas de Dufaur, partido de Saavedra, sudoeste de la provincia de Buenos Aires. Los esporos maduros midieron 4,8 ± 0,05 x 2,4 ± 0,03 μm y la carga (intensidad promedió 5,71 ± 1,49 x 10(6 esporos/abeja. Las detecciones se efectuaron entre julio y octubre de 2006 y la prevalencia en las colmenas positivas osciló entre 1 y 16,7 %. Las características morfológicas de los esporos, el lugar de desarrollo y la especie huésped involucrada sugieren que el microorganismo en cuestión, pertenece al género Nephridiophaga y sería N. apis Ivani, especie tipo cuyo conocimiento es extremadamente limitado. El hallazgo constituye el primer registro de un nefridiofágido asociado a A mellifera fuera del continente europeo.During surveys for the detection of protists associated to Apidae in the Pampas region, biconcave oval spores, and spore clumps were observed in the Malpighian tubules of honeybees from Dufaur, Saavedra county, southwestern Buenos Aires province. Mature spores measured 4.8 ± 0.05 x 2.4 ± 0.03 μm, and mean spore load was 5.71 ± 1.49 x 10(6 per honeybee. Detections were from July to October 2006, and prevalence in positive colonies ranged from 1 to 16.7%. Morphology of the spores, the site of development, and the identity of the host species suggest that the isolated microorganism belongs to the genus Nephridiophaga and would be N apis Ivani, the type species, knowledge on which is extremely limited. The finding constitutes the first record of a nephridiophagid in honeybees outside of Europe.

  12. Toxicity and poisoning symptoms of selected insecticides to honey bees (Apis mellifera mellifera L.

    Directory of Open Access Journals (Sweden)

    Pashte Vrushali Vijaykumar

    2018-01-01

    Full Text Available Bees are potential pollinators of wide variety of crops. The European dark bee, Apis mellifera mellifera (L. is widely used for crop pollination. However, pesticide usage in modern agriculture has threatened the plant-bee pollinator interaction. There is lack of data regarding lethal time, insecticide concentration and poisoning symptoms, especially for formulated insecticides that are widely used in insect management. This study shows that the intrinsic toxicity of insecticides (LC50 to A. mellifera mellifera (L. was in the following order: imidacloprid (0.0070 > fipronil (0.0125 > indoxacarb (0.0266> cypermethrin (0.0370 > dimethoate (0.0385. The lethal time (LT50 values (h in the ascending order of toxicity of insecticides were as follows: fipronil (6.56, cypermethrin (6.69, dimethoate (8.00, imidacloprid (9.85 and indoxacarb (13.45. Distinct poisoning symptoms observed in A. mellifera mellifera were extended proboscis, expanded wings, unhooked wings, extended legs and twisted bodies, defecation on cage covers, sting in release-out position and anus with excreta. All the tested pesticides are harmful to the honey bee except azadirachtin. The tested pesticides exhibited different poisoning symptoms in bees, which could be useful for beekeepers in identifying the cause of colony mortality. In conclusion, the pesticide toxicological research on bees is an important safety aspect for beneficial organisms. This study reveals a realistic acute toxicity in the field of commonly used insecticides. The information is important for insecticide selection in order to minimize direct killing of foraging honey bees while maintaining effective management of crop pests.

  13. TEMPERATURE AND HEAT FLOW WHEN TAPPING OF THE HARDENED STEEL USING DIFFERENT COOLING SYSTEMS TEMPERATURA Y FLUJO DE CALOR AL ROSCAR CON MACHOS ACERO ENDURECIDO UTILIZANDO DIVERSOS SISTEMAS DE LUBRICACIÓN

    Directory of Open Access Journals (Sweden)

    Lincoln Cardoso Brandão

    2009-08-01

    Full Text Available Machining hardened steels has always been a great challenge in metal cutting, particularly for tapping operations. In the present paper, temperature was assessed when tapping hardened AISI H13. Dry machining and two cooling/lubrication systems were used: flooded and minimum quantity of fluid (MQF with 20ml/h, both using mineral oil. The tapping operation was performed on 100 x 40 mm, 14 mm thick workpieces with 55 HRc. An implanted thermocouple technique was used for temperature measurement at distances very close to the highest thread diameter (at 0.1, 2.5 and 5.0 mm. Three thermocouples were used for each distance along the workpiece diameter at 3.0, 7.0 and 11.0 mm from the tap entrance. Measurements were replicated twice for each condition tested. An analytical theoretical heat conduction model was used to evaluate the temperature at the tool-workpiece interface and determine the heat flow and convection coefficient. The smallest temperature increase and heat flow were observed when using the flooded system, followed by the MQF, compared to the dry condition. The effect was directly proportional to the amount of lubricant applied, as well as with the MQF system, when compared to dry cutting.Trabajar los aceros endurecidos siempre ha sido un desafío para el corte de metales, particularmente en las operaciones de roscado. En el presente trabajo se mide la temperatura del acero AISI H13 endurecido, realizándose ensayos sin lubricación (seco y dos sistemas con lubricación: aceite lubricante en grandes cantidades y mínima cantidad de líquido (minimum quantity of fluid MQF a 20 ml/h, en ambos casos se utilizó aceite integral mineral. El roscado se realiza sobre probetas de prueba de 100 x 40 mm con 14mm de espesor y dureza de 55 HRc. Para medir la temperatura se utiliza la técnica de termocuplas situadas muy próximas al diámetro mayor del hilo de rosca (a 0.1, 2.5 y 5 mm de distancia. Se utiliza tres termocuplas a lo largo del espesor de

  14. 5.2 GHz variable-gain amplifier and power amplifier driver for WLAN IEEE 802.11a transmitter front-end

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Xuelian; Yan Jun; Shi Yin [Institute of Semiconductors, Chinese Academy of Sciences, Beijing 100083 (China); Foster, Dai Fa, E-mail: xlzhang@semi.ac.c [Department of Electrical and Computer Engineering, Auburn University, Auburn, AL 36849-5201 (United States)

    2009-01-15

    A 5.2 GHz variable-gain amplifier (VGA) and a power amplifier (PA) driver are designed for WLAN IEEE 802.11a monolithic RFIC. The VGA and the PA driver are implemented in a 50 GHz 0.35 mum SiGe BiCMOS technology and occupy 1.12 x 1.25 mm{sup 2} die area. The VGA with effective temperature compensation is controlled by 5 bits and has a gain range of 34 dB. The PA driver with tuned loads utilizes a differential input, single-ended output topology, and the tuned loads resonate at 5.2 GHz. The maximum overall gain of the VGA and the PA driver is 29 dB with the output third-order intercept point (OIP3) of 11 dBm. The gain drift over the temperature varying from -30 to 85 deg. C converges within +-3 dB. The total current consumption is 45 mA under a 2.85 V power supply.

  15. Study of the failure in service of a linepipe, helicoidally welded, quality API SL GrB wich conveyed natural gas. Estudio del fallo en servicio de una tuberia soldada helicoidalmente de calidad API SL SrB que transportaba gas natural

    Energy Technology Data Exchange (ETDEWEB)

    Gutierrez de Saiz-Solabarria, S.; Elices, M.A. (Departamento de Ciencias de los Materiales e Ingenieria Metalurgica, Universidad del Pais Vasco, Bilbao (Spain))

    1994-01-01

    The possible causes are studied which have incidentally provoked a failure in service on a natural gas linepipe run. This pipe has been manufactured with 6 mm-thick-plate-coil helicoidally welded to 273 mm external diameter. The quality of the material is up to standard API 5L for Grade B and an automatic-helicoidally welding procedure has been with simultaneous inflow at both internal and and external surfaces. The failure appears together with deformations and fracture. (Author)

  16. Foraging dynamics and pollination efficiency of Apis mellifera and Xylocopa olivacea on Luffa aegyptiaca Mill (Cucurbitaceae in southern Ghana

    Directory of Open Access Journals (Sweden)

    Mensah, Ben

    2011-05-01

    Full Text Available As a result of different levels of pollination efficiency of pollinators, knowledge on appropriate pollinators of a plant has become important, especially in the management and conservation of both the pollinators and the plants. In this study, the pollination efficiency of Apis mellifera and Xylocopa olivacea, important pollinators of Luffa aegyptiaca, were assessed in the southern coastal part of Ghana from June 2009 to September 2010. Pollination efficiency of A. mellifera and X. olivacea was estimated in terms of fruit set and fruit size. Further, data on daily and seasonal nectar dynamics of Luffa aegyptiaca were collected. In the early mornings (0600-0700, X. olivacea was the most frequent visitor (0.47 min-1 on the female flowers compared to A. mellifera (0.13 min-1. The mean nectar (sugar concentration in the dry season was 36.58 ± 0.55 %, which was higher than the 34.03 ± 0.38 % obtained for the rainy season (F = 14.986; df = 2; P χ2 = 14.33, df = 1, P X. olivacea had a mean weight of 428.7g and were 1.5 times heavier than fruits from flowers visited by A. mellifera (286.76 g. X. olivacea was more efficient than A. mellifera in terms of number of fruit set per single visit. This study has provided some knowledge on pollination ecology of L. aegyptiaca, which can be exploited to improve fruit production in commercially grown vine crops.

  17. 48 CFR 52.217-5 - Evaluation of Options.

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Evaluation of Options. 52....217-5 Evaluation of Options. As prescribed in 17.208(c), insert a provision substantially the same as the following: Evaluation of Options (JUL 1990) Except when it is determined in accordance with FAR 17...

  18. Protocolo para evaluar y comparar la respuesta al contacto por indentación esférica de un sistema integrado por un recubrimiento cerámico depositado sobre un acero de herramienta

    OpenAIRE

    Cordier, Delphine

    2009-01-01

    En aplicaciones como el conformado en frío donde las herramientas están sometidas a diversas cargas, se usan materiales para herramientas como aceros rápidos y metales duros recubiertos. En estas aplicaciones, los impactos sucesivos inducen presiones que pueden ocasionar el fallo por fatiga. Por ello, es necesario establecer las condiciones límite de trabajo de los materiales para optimizar la vida útil de las herramientas. En este trabajo, el sistema sustrato/recubrimiento ana...

  19. DySectAPI: Scalable Prescriptive Debugging

    DEFF Research Database (Denmark)

    Jensen, Nicklas Bo; Karlsson, Sven; Quarfot Nielsen, Niklas

    We present the DySectAPI, a tool that allow users to construct probe trees for automatic, event-driven debugging at scale. The traditional, interactive debugging model, whereby users manually step through and inspect their application, does not scale well even for current supercomputers. While...... lightweight debugging models scale well, they can currently only debug a subset of bug classes. DySectAPI fills the gap between these two approaches with a novel user-guided approach. Using both experimental results and analytical modeling we show how DySectAPI scales and can run with a low overhead...

  20. Review of Current Student-Monitoring Techniques used in eLearning-Focused recommender Systems and Learning analytics. The Experience API & LIME model Case Study

    Directory of Open Access Journals (Sweden)

    Alberto Corbi

    2014-09-01

    Full Text Available Recommender systems require input information in order to properly operate and deliver content or behaviour suggestions to end users. eLearning scenarios are no exception. Users are current students and recommendations can be built upon paths (both formal and informal, relationships, behaviours, friends, followers, actions, grades, tutor interaction, etc. A recommender system must somehow retrieve, categorize and work with all these details. There are several ways to do so: from raw and inelegant database access to more curated web APIs or even via HTML scrapping. New server-centric user-action logging and monitoring standard technologies have been presented in past years by several groups, organizations and standard bodies. The Experience API (xAPI, detailed in this article, is one of these. In the first part of this paper we analyse current learner-monitoring techniques as an initialization phase for eLearning recommender systems. We next review standardization efforts in this area; finally, we focus on xAPI and the potential interaction with the LIME model, which will be also summarized below.

  1. APIs and Researchers: The Emperor's New Clothes?

    Directory of Open Access Journals (Sweden)

    Jennifer Edmond

    2015-02-01

    Full Text Available As part of the Europeana Cloud (eCloud project, Trinity College Dublin investigated best practice in the use of web services, such as APIs, for accessing large data sets from cultural heritage collections. This research looked into the provision and use of APIs, and moreover, whether or not more customised programmatic access to datasets is what researchers want or need. In order to understand whether current patterns of API usage reflect a skills gap on the part of researchers or a mismatch of tool to purpose, we looked not only at the creators and developer/users of APIs, but also at humanists already re-using big data; approaches in cultural heritage institutions and other research infrastructures to bring API use to non-technical audiences; and the kinds of training and other support services available or emerging within the data-intensive humanities research lifecycle. We conducted both desk research and a series of 11 interviews with figures working as researchers, developers or data providers, including figures from both the API development and the data usage communities. This research, conducted under the eCloud project and supported by the European Commission’s ICT Policy and Support Programme (Grant number 325091, was begun in March 2014 and is now in its concluding validation stage. The results of the research are not yet finalised, but the contribution is already emerging of this work to the debate about APIs being either the way forward for digital cultural heritage collections, or the Emperor’s New Clothes (or maybe a bit of both.

  2. Syntheses, X-ray structures, solid state high-field electron paramagnetic resonance, and density-functional theory investigations on chloro and aqua Mn(II) mononuclear complexes with amino-pyridine pentadentate ligands.

    Science.gov (United States)

    Hureau, Christelle; Groni, Sihem; Guillot, Régis; Blondin, Geneviève; Duboc, Carole; Anxolabéhère-Mallart, Elodie

    2008-10-20

    The two pentadentate amino-pyridine ligands L5(2) and L5(3) (L5(2) and L5(3) stand for the N-methyl-N,N',N'-tris(2-pyridylmethyl)ethane-1,2-diamine and the N-methyl-N,N',N'-tris(2-pyridylmethyl)propane-1,3-diamine, respectively) were used to synthesize four mononuclear Mn(II) complexes, namely [(L5(2))MnCl](PF6) (1(PF6)), [(L5(3))MnCl](PF6) (2(PF6)), [(L5(2))Mn(OH2)](BPh4)2 (3(BPh4)2), and [(L5(3))Mn(OH2)](BPh4)2 (4(BPh4)2). The X-ray diffraction studies revealed different configurations for the ligand L5(n) (n = 2, 3) depending on the sixth exogenous ligand and/or the counterion. Solid state high-field electron paramagnetic resonance spectra were recorded on complexes 1-4 as on previously described mononuclear Mn(II) systems with tetra- or hexadentate amino-pyridine ligands. Positive and negative axial zero-field splitting (ZFS) parameters D were determined whose absolute values ranged from 0.090 to 0.180 cm(-1). Density-functional theory calculations were performed unraveling that, in contrast with chloro systems, the spin-spin and spin-orbit coupling contributions to the D-parameter are comparable for mixed N,O-coordination sphere complexes.

  3. Modelado de Control de Nivel en Molde para Vaciado Continuo de Palanquillas de Acero

    Directory of Open Access Journals (Sweden)

    Guillermo González Yero

    2014-01-01

    Full Text Available Resumen: Este trabajo presenta un modelo del sistema de control de nivel en molde de una máquina de vaciado continuo de palanquillas de acero. El objetivo fue realizar el modelado de cada elemento del sistema incluyendo las perturbaciones y transformaciones de la planta que más afectan la calidad del control. Se obtuvo y validó un modelo aproximado, utilizando leyes físicas, la identificación experimental mediante señales especiales e identificación paramétrica fuera de línea. En el modelo se incluyen de forma explícita los fenómenos de obstrucción y erosión en la válvula, que tienen una incidencia significativa en el funcionamiento de la planta. Para el servosistema hidráulico de la instalación se logró un modelo de caja gris que contribuye a un mejor entendimiento del comportamiento del proceso y a evaluar la incidencia de una implementación multifrecuencia bajo esquema convencional. Con el modelo obtenido es posible estudiar la operación del sistema a escala de simulación y la efectividad de soluciones de control avanzadas. El trabajo desarrollado es parte de un proceso de I+D que en el transcurso de más de 10 años ha contribuido a que en la acería donde se realiza la investigación, exista un sistema de control de nivel en molde que tiene impacto positivo sobre la calidad del acero producido. Abstract: This paper presents a model of system for the mould level control in a continuous casting machine for steel billets. The objective was to carry out the modeling of each element of the system including disturbances and transformations of the plant that affect the quality of control in the installation study object. It was obtained and validated an approximate model of the control system using physical laws governing the same one, experimental identification by special signals and parametric identification off- line. The model explicitly includes the phenomena of obstruction and erosion of the valve which have a

  4. USAJOBS Job Opportunity Announcements (JOA) REST API

    Data.gov (United States)

    Office of Personnel Management — This REST-based API is designed to support lightweight Federal Job Opportunity Announcement (JOA) content consumption by consumers. It is anticipated that this API...

  5. Análisis experimental del desgaste entre UHMWPE y acero inoxidable 316l empleados en la manufactura de prótesis coxofemorales

    Directory of Open Access Journals (Sweden)

    Ricardo Gustavo Rodríguez Cañizo

    2010-07-01

    Full Text Available Título en inglés: Experimental wear analysis of UHMWPE and stainless 316l used in the manufacturing of coxofemoral prosthesis. Resumen La causa más común de falla en prótesis coxofemorales es el aflojamiento entre los componentes que conforman el sistema, de manera específica la copa acetabular y la cabeza femoral. En esta investigación se presenta un análisis tribológico del desgaste en los componentes mencionados, ya que cuando las superficies en contacto se desgastan, la funcionalidad mecánica del sistema se compromete, debido al cambio de geometría de los mismos, dando como resultado un juego mecánico entre la copa y la cabeza. Los materiales considerados en este estudio son el polietileno de ultra elevado peso molecular (UHMWPE, por sus siglas en inglés para la copa acetabular, y acero inoxidable 316L para la cabeza femoral. Esta combinación de materiales representa hoy en día la recomendación más usual por parte de los cirujanos para pacientes de la tercera edad. La tasa anual de desgaste se determinó de manera experimental y se cuantificó la cantidad de material desprendido durante el contacto. Se establecieron las condiciones de carga de forma analítica, considerando las que actúan sobre la cabeza femoral a lo largo del área de desgaste durante la marcha humana. Posteriormente, se realizó el análisis experimental de desgaste utilizando una máquina tribológica de configuración perno-sobre-disco (pin-on-disk, diseñada de manera específica para este estudio. Las pruebas para determinar la pérdida volumétrica de los componentes se realizaron bajo tres condiciones de operación: en seco, lubricada con agua destilada y lubricada con suero bovino. El marco experimental considerado consistió en pernos de UHMWPE sobre discos de acero inoxidable 316L simulando el desgaste equivalente a diez años de uso de la prótesis. Finalmente, de los resultados obtenidos se puede establecer que el desgaste y la cantidad de part

  6. Conversion of 2-deoxy-D-ribose into 2-amino-5-(2-deoxy-beta-D-ribofuranosyl)pyridine, 2'-deoxypseudouridine, and other C-(2'-deoxyribonucleosides).

    Science.gov (United States)

    Reese, Colin B; Wu, Qinpei

    2003-09-21

    The synthesis of 2-amino-5-(2-deoxy-beta-D-ribofuranosyl)pyridine 2a, 2-amino-5-(2-deoxy-alpha-D-ribofuranosyl)-pyridine 23, 2-amino-5-(2-deoxy-beta-D-ribofuranosyl)-3-methylpyridine 2b, 2-amino-5-(2-deoxy-alpha-D-ribofuranosyl)-3-methylpyridine 29 and 5-(2-deoxy-beta-D-ribofuranosyl)-2,4-dioxopyrimidine [2'-deoxypseudouridine] 30a is described. These C-nucleosides are prepared either from 2-deoxy-3,5-O-(1,1,3,3-tetraisopropyldisiloxan-1,3-diyl)-D-ribofuranose 15 or from 2-deoxy-3,5-O-(1,1,3,3-tetraisopropyldisiloxan-1,3-diyl)-D-ribono-1,4-lactone 16, which are themselves prepared from 2-deoxy-D-ribose 13. The sugar derivatives are first allowed to react with the appropriate 5-lithio-pyridine or 5-lithio-pyrimidine derivatives, which are prepared from 5-bromo-2-(dibenzylamino)pyridine 12a, 5-bromo-2-[bis(4-methoxybenzyl)amino]pyridine 12b, 5-bromo-2-dibenzylamino-3-methylpyridine 25 and 5-bromo-2,4-bis(4-methoxybenzyloxy)pyrimidine 33. The products from the reactions between the lithio-derivatives and the lactol 15 are cyclized under Mitsunobu conditions; the products from the reactions between the lithio-derivatives and the lactone 16 are first reduced with L-Selectride before cyclization, also under Mitsunobu conditions. In all cases, the beta-anomers of the protected C-nucleosides are the predominant products. Finally, the separation of the alpha- and beta-anomers and the removal of all of the protecting groups are described.

  7. Copper L X-ray spectra measured by a high resolution ion-induced X-ray spectrometer

    Energy Technology Data Exchange (ETDEWEB)

    Takahashi, Ryohei; Hamaguchi, Dai; Kageyama, Hiroyoshi [Kyoto Inst. of Tech. (Japan); and others

    1997-03-01

    High resolution L X-ray emission spectra of Cu have been measured by 0.75 MeV/u H, He, and F, 0.73 MeV/u Ar, 0.64 MeV/u Si, and 0.073 MeV/u Si ion impacts with a crystal spectrometer. The X-ray transition energies in the Cu target for L{iota}, L{eta}, L{alpha}{sub 1,2}, L{beta}{sub 1}, and L{beta}{sub 3,4} diagram lines induced by light ion impacts are determined, which are in good agreement with those given in the reference. The difference in L X-ray emission spectra produced by H, He, F, Si, and Ar ions are considered and the L{alpha}{sub 1,2} and L{beta}{sub 1} emission spectra are compared with the calculated ones based on the multiconfiguration Dirac-Fock method. (author)

  8. Selenium toxicity to honey bee (Apis mellifera L. pollinators: effects on behaviors and survival.

    Directory of Open Access Journals (Sweden)

    Kristen R Hladun

    Full Text Available We know very little about how soil-borne pollutants such as selenium (Se can impact pollinators, even though Se has contaminated soils and plants in areas where insect pollination can be critical to the functioning of both agricultural and natural ecosystems. Se can be biotransferred throughout the food web, but few studies have examined its effects on the insects that feed on Se-accumulating plants, particularly pollinators. In laboratory bioassays, we used proboscis extension reflex (PER and taste perception to determine if the presence of Se affected the gustatory response of honey bee (Apis mellifera L., Hymenoptera: Apidae foragers. Antennae and proboscises were stimulated with both organic (selenomethionine and inorganic (selenate forms of Se that commonly occur in Se-accumulating plants. Methionine was also tested. Each compound was dissolved in 1 M sucrose at 5 concentrations, with sucrose alone as a control. Antennal stimulation with selenomethionine and methionine reduced PER at higher concentrations. Selenate did not reduce gustatory behaviors. Two hours after being fed the treatments, bees were tested for sucrose response threshold. Bees fed selenate responded less to sucrose stimulation. Mortality was higher in bees chronically dosed with selenate compared with a single dose. Selenomethionine did not increase mortality except at the highest concentration. Methionine did not significantly impact survival. Our study has shown that bees fed selenate were less responsive to sucrose, which may lead to a reduction in incoming floral resources needed to support coworkers and larvae in the field. If honey bees forage on nectar containing Se (particularly selenate, reductions in population numbers may occur due to direct toxicity. Given that honey bees are willing to consume food resources containing Se and may not avoid Se compounds in the plant tissues on which they are foraging, they may suffer similar adverse effects as seen in other

  9. 47 CFR 61.46 - Adjustments to the API.

    Science.gov (United States)

    2010-10-01

    ... 47 Telecommunication 3 2010-10-01 2010-10-01 false Adjustments to the API. 61.46 Section 61.46... Rules for Dominant Carriers § 61.46 Adjustments to the API. (a) Except as provided in paragraphs (d) and... carrier must calculate an API for each affected basket pursuant to the following methodology: APIt = APIt...

  10. An example of how to handle amorphous fractions in API during early pharmaceutical development: SAR114137--a successful approach.

    Science.gov (United States)

    Petzoldt, Christine; Bley, Oliver; Byard, Stephen J; Andert, Doris; Baumgartner, Bruno; Nagel, Norbert; Tappertzhofen, Christoph; Feth, Martin Philipp

    2014-04-01

    The so-called pharmaceutical solid chain, which encompasses drug substance micronisation to the final tablet production, at pilot plant scale is presented as a case study for a novel, highly potent, pharmaceutical compound: SAR114137. Various solid-state analytical methods, such as solid-state Nuclear Magnetic Resonance (ssNMR), Differential Scanning Calorimetry (DSC), Dynamic Water Vapour Sorption Gravimetry (DWVSG), hot-stage Raman spectroscopy and X-ray Powder Diffraction (XRPD) were applied and evaluated to characterise and quantify amorphous content during the course of the physical treatment of crystalline active pharmaceutical ingredient (API). DSC was successfully used to monitor the changes in amorphous content during micronisation of the API, as well as during stability studies. (19)F solid-state NMR was found to be the method of choice for the detection and quantification of low levels of amorphous API, even in the final drug product (DP), since compaction during tablet manufacture was identified as a further source for the formation of amorphous API. The application of different jet milling techniques was a critical factor with respect to amorphous content formation. In the present case, the change from spiral jet milling to loop jet milling led to a decrease in amorphous API content from 20-30 w/w% to nearly 0 w/w% respectively. The use of loop jet milling also improved the processability of the API. Stability investigations on both the milled API and the DP showed a marked tendency for recrystallisation of the amorphous API content on exposure to elevated levels of relative humidity. No significant impact of amorphous API on either the chemical stability or the dissolution rate of the API in drug formulation was observed. Therefore, the presence of amorphous content in the oral formulation was of no consequence for the clinical trial phases I and II. Copyright © 2013 Elsevier B.V. All rights reserved.

  11. Function and distribution of 5-HT2 receptors in the honeybee (Apis mellifera.

    Directory of Open Access Journals (Sweden)

    Markus Thamm

    Full Text Available BACKGROUND: Serotonin plays a pivotal role in regulating and modulating physiological and behavioral processes in both vertebrates and invertebrates. In the honeybee (Apis mellifera, serotonin has been implicated in division of labor, visual processing, and learning processes. Here, we present the cloning, heterologous expression, and detailed functional and pharmacological characterization of two honeybee 5-HT2 receptors. METHODS: Honeybee 5-HT2 receptor cDNAs were amplified from brain cDNA. Recombinant cell lines were established constitutively expressing receptor variants. Pharmacological properties of the receptors were investigated by Ca(2+ imaging experiments. Quantitative PCR was applied to explore the expression patterns of receptor mRNAs. RESULTS: The honeybee 5-HT2 receptor class consists of two subtypes, Am5-HT2α and Am5-HT2β. Each receptor gene also gives rise to alternatively spliced mRNAs that possibly code for truncated receptors. Only activation of the full-length receptors with serotonin caused an increase in the intracellular Ca(2+ concentration. The effect was mimicked by the agonists 5-methoxytryptamine and 8-OH-DPAT at low micromolar concentrations. Receptor activities were blocked by established 5-HT receptor antagonists such as clozapine, methiothepin, or mianserin. High transcript numbers were detected in exocrine glands suggesting that 5-HT2 receptors participate in secretory processes in the honeybee. CONCLUSIONS: This study marks the first molecular and pharmacological characterization of two 5-HT2 receptor subtypes in the same insect species. The results presented should facilitate further attempts to unravel central and peripheral effects of serotonin mediated by these receptors.

  12. Function and distribution of 5-HT2 receptors in the honeybee (Apis mellifera).

    Science.gov (United States)

    Thamm, Markus; Rolke, Daniel; Jordan, Nadine; Balfanz, Sabine; Schiffer, Christian; Baumann, Arnd; Blenau, Wolfgang

    2013-01-01

    Serotonin plays a pivotal role in regulating and modulating physiological and behavioral processes in both vertebrates and invertebrates. In the honeybee (Apis mellifera), serotonin has been implicated in division of labor, visual processing, and learning processes. Here, we present the cloning, heterologous expression, and detailed functional and pharmacological characterization of two honeybee 5-HT2 receptors. Honeybee 5-HT2 receptor cDNAs were amplified from brain cDNA. Recombinant cell lines were established constitutively expressing receptor variants. Pharmacological properties of the receptors were investigated by Ca(2+) imaging experiments. Quantitative PCR was applied to explore the expression patterns of receptor mRNAs. The honeybee 5-HT2 receptor class consists of two subtypes, Am5-HT2α and Am5-HT2β. Each receptor gene also gives rise to alternatively spliced mRNAs that possibly code for truncated receptors. Only activation of the full-length receptors with serotonin caused an increase in the intracellular Ca(2+) concentration. The effect was mimicked by the agonists 5-methoxytryptamine and 8-OH-DPAT at low micromolar concentrations. Receptor activities were blocked by established 5-HT receptor antagonists such as clozapine, methiothepin, or mianserin. High transcript numbers were detected in exocrine glands suggesting that 5-HT2 receptors participate in secretory processes in the honeybee. This study marks the first molecular and pharmacological characterization of two 5-HT2 receptor subtypes in the same insect species. The results presented should facilitate further attempts to unravel central and peripheral effects of serotonin mediated by these receptors.

  13. Long-Term Temporal Trends of Nosema spp. Infection Prevalence in Northeast Germany: Continuous Spread of Nosema ceranae, an Emerging Pathogen of Honey Bees (Apis mellifera), but No General Replacement of Nosema apis.

    Science.gov (United States)

    Gisder, Sebastian; Schüler, Vivian; Horchler, Lennart L; Groth, Detlef; Genersch, Elke

    2017-01-01

    The Western honey bee ( Apis mellifera ) is widely used as commercial pollinator in worldwide agriculture and, therefore, plays an important role in global food security. Among the parasites and pathogens threatening health and survival of honey bees are two species of microsporidia, Nosema apis and Nosema ceranae. Nosema ceranae is considered an emerging pathogen of the Western honey bee. Reports on the spread of N. ceranae suggested that this presumably highly virulent species is replacing its more benign congener N. apis in the global A. mellifera population. We here present a 12 year longitudinal cohort study on the prevalence of N. apis and N. ceranae in Northeast Germany. Between 2005 and 2016, a cohort of about 230 honey bee colonies originating from 23 apiaries was sampled twice a year (spring and autumn) resulting in a total of 5,600 bee samples which were subjected to microscopic and molecular analysis for determining the presence of infections with N. apis or/and N. ceranae . Throughout the entire study period, both N. apis - and N. ceranae -infections could be diagnosed within the cohort. Logistic regression analysis of the prevalence data demonstrated a significant increase of N. ceranae -infections over the last 12 years, both in autumn (reflecting the development during the summer) and in spring (reflecting the development over winter) samples. Cell culture experiments confirmed that N. ceranae has a higher proliferative potential than N. apis at 27° and 33°C potentially explaining the increase in N. ceranae prevalence during summer. In autumn, characterized by generally low infection prevalence, this increase was accompanied by a significant decrease in N. apis -infection prevalence. In contrast, in spring, the season with a higher prevalence of infection, no significant decrease of N. apis infections despite a significant increase in N. ceranae infections could be observed. Therefore, our data do not support a general advantage of N. ceranae over

  14. MODIFICACIÓN DEL SISTEMA CONCRETO-ACERO DE REFUERZO MEDIANTE LA ADICIÓN DE FIBRAS DE BAGAZO DE CAÑA PARA FACILITAR SU PROTECCIÓN ANTICORROSIVA.

    OpenAIRE

    GARCIA DELGADO, AMERICA

    2015-01-01

    Los sistemas concreto-acero de refuerzo son considerados estructuras durables y resistentes; sin embargo, con el paso del tiempo se ven afectados por problemas de corrosión, la cual, se desarrolla cuando los cloruros se encuentran más allá de un cierto nivel umbral, en el que se inicia la despasivación o la ruptura la capa pasiva que protege al acero de refuerzo. Para contrarrestar los daños ocasionados por la corrosión, se han propuestos varios métodos para disminuir y/o preve...

  15. [Melissopalynology and trophic niche of Apis cerana ceraca and Apis mellifera ligustica in Yunnan Province of Southwest China].

    Science.gov (United States)

    Liu, Yu-Jia; Zhao, Tian-Rui; Zhao, Feng-Yun

    2013-01-01

    In 2010 and 2011, the honey samples of Apis cerana cerana and A. mellifera ligustica were collected from Kunming and Mengzi of Yunnan Province, respectively, aimed to analyze the melissopalynology and tropic niche of the two bee species. The absolute pollen concentration of the honey of A. cerana cerana was 1.55 x 10(4) ind x g(-1), being significantly higher than that (1.01 x 10(4) ind x g(-1)) of A. mellifera ligustica, and the number of nectar plant species collected by A. cerana cerana was 12.9, also significantly higher than that (7.7) collected by A. mellifera ligustica, indicating that A. cerana cerana could utilize more nectar plants, while A. mellifera ligustica had stronger selectivity to the nectar plants. The trophic niche breadth of A. cerana cerana was 0.35, which was significantly higher than that (0.23) of A. mellifera ligustica. The trophic niche overlap index between the two bee species was 0.71, and the interspecific competition index was 0.93, suggesting that the food competition between A. cerana cerana and A. mellifera ligustica was fierce.

  16. Spent fuel transport and storage system for NOK: The TN52L, TN97L, TN24 BHL and TN24 GB casks

    International Nuclear Information System (INIS)

    Wattez, L.; Verdier, A.; Monsigny, P.-A.

    2007-01-01

    NOK nuclear power plants in Switzerland, LEIBSTADT (KKL) BWR nuclear power plant and BEZNAU (KKB) PWR nuclear power plant have opted to ship spent fuel to a central facility called ZWILAG for interim storage. In the mid-nineties, COGEMA LOGISTICS was contracted by KKL for the supply of the TN52L and TN97L transport and storage casks for BWR fuel types. In 2003, KKL also ordered from COGEMA LOGISTICS the supply of six TN24 BHL transport and storage casks. This paper shows how all the three cask designs have responded to the KKL needs to ship and store BWR spent fuel. In addition, it highlights the already significant operational feedback of the TN52L and TN97L casks by the KKL and ZWILAG operators. In 2004, NOK also ordered three TN24 GB transport and storage casks for PWR fuel types. These casks are presently being manufactured. (author)

  17. Thermal degradation of a synthetic lube oil API SL/CF SAE 5W 40; Degradacao termica do oleo lubrificante sintetico API SL/CF SAE 5W 40

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, Eddy H. de O.; Carvalho, Laura H. de; Silva, Everson de L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2008-07-01

    This work deals with the thermal degradation to 210 deg C of lubricating oil synthetic API SL/CF SAE 5W 40 as received and on the presence of metallic particles, from engine parts (head and crankshaft). Samples were collected at various intervals of time. The metallic particles were spent in mesh sieve no. 200 (0.074 mm) and used both in the trials of characterization (EDX and SEM) as the thermal degradation of the oil. Changes in rheology, viscosity, density, color and FTIR were monitored over time of heat exposure. The results indicate that thermal exposure caused by thermal oxidation of synthetic oil and that the presence of metallic particles (10 ppm) accelerated this process, so it is suggested that during the exchange of oil are taken care to remove them from to prevent the premature deterioration of the new oil. The behaviour Newtonian was maintained throughout the period degradation and viscosity of the oil has not changed significantly even after long periods (1148 hours) of thermal exposure. Despite the density of oil also has not changed significantly with time of exposure, changes in color indicate that chemical changes occurred, which was detected by FTIR. (author)

  18. Production of lipopeptide biosurfactants by Bacillus atrophaeus 5-2a and their potential use in microbial enhanced oil recovery.

    Science.gov (United States)

    Zhang, Junhui; Xue, Quanhong; Gao, Hui; Lai, Hangxian; Wang, Ping

    2016-10-03

    Lipopeptides are known as promising microbial surfactants and have been successfully used in enhancing oil recovery in extreme environmental conditions. A biosurfactant-producing strain, Bacillus atrophaeus 5-2a, was recently isolated from an oil-contaminated soil in the Ansai oilfield, Northwest China. In this study, we evaluated the crude oil removal efficiency of lipopeptide biosurfactants produced by B. atrophaeus 5-2a and their feasibility for use in microbial enhanced oil recovery. The production of biosurfactants by B. atrophaeus 5-2a was tested in culture media containing eight carbon sources and nitrogen sources. The production of a crude biosurfactant was 0.77 g L -1 and its surface tension was 26.52 ± 0.057 mN m -1 in a basal medium containing brown sugar (carbon source) and urea (nitrogen source). The biosurfactants produced by the strain 5-2a demonstrated excellent oil spreading activity and created a stable emulsion with paraffin oil. The stability of the biosurfactants was assessed under a wide range of environmental conditions, including temperature (up to 120 °C), pH (2-13), and salinity (0-50 %, w/v). The biosurfactants were found to retain surface-active properties under the extreme conditions. Additionally, the biosurfactants were successful in a test to simulate microbial enhanced oil recovery, removing 90.0 and 93.9 % of crude oil adsorbed on sand and filter paper, respectively. Fourier transform infrared spectroscopy showed that the biosurfactants were a mixture of lipopeptides, which are powerful biosurfactants commonly produced by Bacillus species. The study highlights the usefulness of optimization of carbon and nitrogen sources and their effects on the biosurfactants production and further emphasizes on the potential of lipopeptide biosurfactants produced by B. atrophaeus 5-2a for crude oil removal. The favorable properties of the lipopeptide biosurfactants make them good candidates for application in the bioremediation of oil

  19. Influencia de la temperatura de austenización y tiempo de permanencia sobre el tamaño de grano en aceros ferrítico-martensíticos del tipo 9Cr1MoVNb utilizados en calderas supercríticas

    Directory of Open Access Journals (Sweden)

    Gutiérrez-Urrutia, L.

    2001-04-01

    Full Text Available The aim of the present work is to determine the influence of austenitizing temperature holding time and heating velocity on grain size of ferritic-martensitic type 9CrlMoVNb steels developed for Oak Ridge National Laboratories & Combustion Engineering, T91/P91[1] Steels (USA and X10CrMoVNb 9.1 (Europe. The potential benefits of this material, in term of high resistance, good ductily and oxidation resistance, weldability and in particular good high temperature creep strength, are now widely acknowledged, particulary by supercritical boilers (P = 300 bar, T = 550±50 °C. The studied steels have been produced in, high frecuency induction vacum furnaces and hot-rolled.

    Se estudia la influencia de la temperatura de austenización, tiempo de permanencia a esta temperatura y velocidad de calentamiento sobre el tamaño de grano de varios aceros ferrítico-martensíticos de última generación del tipo 9CrlMoVNb, desarrollados por Oak Ridge National Laboratories (ORNL conjuntamente con Combustion Enginering en USA, conocidos por ASME/ASTM por las designaciones T91/P91[1] y en Europa como X10CrMoVNb9.1. Son aceros ductiles y tenaces que presentan muy buenas propiedades de resistencia a fluencia, soldabilidad y conductividad térmica. Son cada vez más utilizados como tubos de alta temperatura (550±50 °C y presión (300 bar en calderas supercríticas para centrales térmicas avanzadas. Los aceros estudiados se han fabricado en hornos de inducción de alta frecuencia al vacío y laminados en caliente.

  20. Absconding and migratory behaviors of feral Africanized honey bee (Apis mellifera L. colonies in NE Brazil = Comportamentos de abandono e migração de colônias silvestres da abelha melífera africanizada (Apis mellifera L. no nordeste do Brasil

    Directory of Open Access Journals (Sweden)

    Breno Magalhães Freitas

    2007-10-01

    Full Text Available We investigated the annual movements of feral Africanized honey bee (Apis mellifera L. colonies in the state of Ceará, Brazil, aiming to understand seasonal variations in their population. Arrival and absconding of Africanized honey bee (AHB colonies in the semiaridmunicipality of Canindé and the coastal humid city of Fortaleza (120 km apart were recorded weekly from January 1999 to December 2001, and the data compared to rainfall records in both areas. Results showed that AHB colonies only nest in the semiarid during the rainy season and abscond during the dry season, the opposite from observations taken in Fortaleza. Only 5% of colonies remained in the semiarid area for the entire year due to ant (Camponotus sp. attacks and shortage of nectar and water during the dry season, with most colonies migrating to coastal areas where the weather is milder and many plant species bloom at that time of year. Excessive rainfallprobably pushes AHB colonies back to the semiarid during the rainy season. We concluded that absconding and migration are strategies that allow AHB colonies to survive in the semiarid NE of Brazil, contrary to European honeybees, which have never succeeded in establishing wild colonies in the region.Os movimentos de colônias silvestres da abelha melífera africanizada (Apis mellifera L. no Estado do Ceará, Brasil, foram investigados com o objetivo de compreender variações anuais em sua população. A chegada e a partida de colônias de abelhas africanizadas (AHB,no município semi-árido de Canindé e na úmida cidade litorânea de Fortaleza (separadas por 120 km, foram monitoradas semanalmente, de janeiro de 1999 a dezembro de 2001, e comparados com os dados pluviométricos de chuvas em ambas as áreas. Os resultadosdemonstraram que as abelhas africanizadas somente nidificaram no semi-árido durante a estação chuvosa e o abandonaram na estação seca, ao contrário do observado em Fortaleza. Apenas 5% das col

  1. Estudo do comportamento nutricional dos zangões(Apis mellifera L. após diferentes tempos de jejum

    Directory of Open Access Journals (Sweden)

    Italo Souza Aquino

    2013-05-01

    Full Text Available A aprendizagem olfativa de zangões de abelhas africanizadas (Apis mellifera L. tem sido investigada em condicionamento clássico (CC através do reflexo da extensão da probóscide (PER. O CC entre membros da casta das abelhas merece estudos que possam mostrar diferenças e semelhanças no aprendizado associativo entre esses indivíduos. Zangões e operárias de A. mellifera L. foram igualmente confinados em pequenos tubos de metal e submetidos a diferentes períodos de privação 12, 16, 20 e 24 horas. Os indivíduos sobreviventes a esses períodos foram submetidos a 24 provas em que receberam 12 apresentações de estímulos condicional (EC e incondicional (EI pareados durante aquisição e 12 apresentações de EC na extinção. Observou-se que os longos períodos de jejum não causam grandes retardos da aprendizagem nos zangões. Porém, para que se obtenha um melhor desempenho destes no procedimento de condicionamento recomenda-se períodos de jejum iguais ou inferiores a 12h.

  2. COMPORTAMIENTO DEL CONCRETO REFORZADO CON FIBRAS DE ACERO ZP-306 SOMETIDO A ESFUERZOS DE COMPRESIÓN

    Directory of Open Access Journals (Sweden)

    Lina P. Gallo-Arciniegas

    2013-01-01

    Full Text Available En Colombia, el uso del concreto reforzado con fibras de acero (CRFA es muy limitado, debido a que en el país no existe suficiente evidencia experimental y requisitos reglamentarios al respecto. En el artículo se presentan los resultados de una investigación experimental y analítica sobre el comportamiento del CRFA elaborado con fibras ZP-306, sometidas a esfuerzos de compresión. El estudio involucra la revisión y discusión de los modelos disponibles en la literatura, así como un programa experimental que incluye el ensayo de 48 especímenes. A partir de un análisis de regresión de los datos medidos, se proponen ecuaciones para estimar las principales propiedades mecánicas del CRFA, tales como resistencia a compresión, módulo de elasticidad y relación de Poisson. Las ecuaciones correlacionan las propiedades mecánicas con las principales características de las fibras de acero, tales como dosificación y relación de aspecto.

  3. Fuego y acero

    Directory of Open Access Journals (Sweden)

    Sfintesco, D.

    1965-03-01

    Full Text Available In a brief and appealing manner the author analysis the basic considerations which should be taken into account to deal effectively with the safety of steel structures in case of fire. He makes it clear that the safety measures must not be the result of a rather intuitive and hasty reaction to the possibility of a fire: for example, the costly covering of steel columns with fire resisting material, which in most cases is not necessary. A careful assessment of possible risks must be made, available means to reduce these must be adopted, and the potential losses in case of fire must be taken into account. The article is completed with a brief commentary on the new Italian Regulations, which are probably the most modern and advanced on this matter.El autor expone en este trabajo, en forma breve y llamativa, las bases en que conviene apoyarse para poder resolver racionalmente el problema de la seguridad de las estructuras de acero frente al fuego. Su lectura hace comprender claramente que no puede constituir esta base el temor irreflexivo, con sus secuelas de revestimientos y precauciones onerosos, e innecesarios la mayor parte de las veces, sino la ponderación prudente de los riesgos posibles, de los medios disponibles para combatir el peligro y de los daños probables que del incendio se puedan derivar. Termina el artículo con un rápido comentario del nuevo Reglamento italiano, probablemente el más moderno y avanzado de todos los existentes sobre esta materia de protección contra el fuego.

  4. Effect of natural aging on the microstructural regions, mechanical properties, corrosion resistance and fracture in welded joints on API5L X52 steel pipeline

    Directory of Open Access Journals (Sweden)

    Vargas-Arista, Benjamín

    2014-09-01

    Full Text Available A characterization study was done to analyze how microstructural regions affect the mechanical properties, corrosion and fractography of the Heat Affected Zone (HAZ, weld bead and base metal for pipe naturally aged for 21 years at 30 °C. Results showed that microstructures exhibited damage and consequently decrease in properties, resulting in over-aged due to service. SEM analysis showed that base metal presented coarse ferrite grain. Tensile test indicated that microstructures showed discontinuous yield. Higher tensile strength was obtained for weld bead, which exhibited a lower impact energy in comparison to that of HAZ and base metal associated with brittle fracture by trans-granular cleavage. The degradation of properties was associated with the coarsening of nano-carbides observed through TEM images analysis, which was confirmed by SEM fractography of tensile and impact fracture surfaces. The weld bead reached the largest void density and highest susceptibility to corrosion in H2S media when compared to those of the HAZ and base metal.Se realizó un estudio de caracterización para analizar cómo la microestructura afecta a las propiedades mecánicas, corrosión y fractura de la zona afectada por calor (ZAC, soldadura y metal base para tubería envejecida naturalmente durante 21 años a 30 °C. Los resultados indicaron que las microestructuras presentaron daño y consecuentemente reducción en propiedades mecánicas, como consecuencia del envejecimiento por servicio. El estudio mediante MEB mostró que el metal base presenta grano ferrítico grueso. La prueba de tensión indicó que las microestructuras mostraron fluencia discontinua. La mayor resistencia a la tracción se presentó en la soldadura, la cual alcanzó menor energía de impacto en comparación con la ZAC y metal base asociado con fractura frágil por clivaje transgranular. La degradación de las propriedades está en relación con el engrosamiento de nanocarburos observados a través del análisis de imágenes por MET, lo que se confirmó mediante fractografía por MEB de superfícies de fractura bajo tensión e impacto. La soldadura alcanzó la mayor densidad de microhuecos y la mayor susceptibilidad a la corrosión en un medio conteniendo H2S que cuando se compara con la ZAC y metal base.

  5. Oxidación en vapor de agua a 700 ºC y 750 ºC del acero inoxidable AISI 317 recubierto con aluminio por CVD-FBR.

    OpenAIRE

    Jose L. Marulanda; Saul I. Castañeda; Aduljay Remolina

    2014-01-01

    Se realizó la oxidación del acero inoxidable austenítico AISI 317 recubierto con aluminio por deposición química de vapor en lecho fluidizado, a temperaturas de 700 °C y 750ºC, en un ambiente con 100% vapor de agua, para evaluar su comportamiento. Se realizaron curvas de ganancia de masa y las películas de óxidos se analizaron por medio de SEM y difracción de rayos X, para observar la morfología de los óxidos. Se realizó la simulación termodinámica del proceso de oxidación en vapor de agua de...

  6. Recent advances in the API quality program

    International Nuclear Information System (INIS)

    Gollhofer, F.R.

    1991-01-01

    The API now has more than 3 years' operating experience in licensing manufacturers under the API Quality Program. The API evaluation procedures, described in this paper, provide consistency in evaluation and should allow full participation of petroleum equipment suppliers in the worldwide market during the 1990's and into the 21st century. The program's flexibility will allow it to cope with significant changes resulting from the planned European Common Market's Global Approach to Certification and Testing scheduled to occur in 1992

  7. USAJOBS Job Opportunity Announcements (JOA) SOAP API

    Data.gov (United States)

    Office of Personnel Management — The purpose of the SOAP based API is to provide the full Federal Job Opportunity Announcement (JOA) content to the consumer. It is anticipated that this API will be...

  8. Corrosión microbiológica en aceros de bajo carbono

    OpenAIRE

    Medina-Custodio, O; Ortiz-Prado, A; Jacobo-Armendáriz, V.H.; Schouwenaars-Franssens, R

    2009-01-01

    La corrosión microbiológica es un tipo común de deterioro que afecta diversas industrias, una de ellas es la petrolera en la que se estiman que el 20% o 30% de fallas en las tuberías de trasporte de hidrocarburos es favorecida por microorganismos. Las reacciones químicas que sustentan éstos, generan transferencia de iones, lo que justifica el empleo de técnicas electroquímicas para su análisis. En este trabajo, se estudiaron probetas de acero de bajo carbono SAE 1018, sumergidas en un medio n...

  9. Synthesis and electrochemical properties of KPb_4_−_xCa_x(PO_4)_3 (0 ≤ x ≤ 1.5) for oxidation of cadmium at graphite electrode

    International Nuclear Information System (INIS)

    Lahrich, Sara; Manoun, Bouchaib; El Mhammedi, Moulay Abderrahim

    2017-01-01

    Chemically modified carbon paste electrode (CPE) for cadmium (II) analysis has been constructed by mixing KPb_4_−_xCa_x(PO_4)_3 (0 ≤ x ≤ 1.5) (CaLA) and graphite powder. The lacunar apatite was synthesized using solid reaction and characterized by X-ray diffraction (XRD), infrared spectroscopy (IR) and Raman spectroscopy. The refinement study was carried out using Rietveld method where the obtained results show a good agreement between the observed and calculated patterns. The detection of cadmium (II) was investigated in acetate buffer (pH 4.5) using differential pulse anodic stripping voltammetry (DPASV). The limit of detection obtained under the optimized experimental conditions was 5.35 × 10"−"7 mol L"−"1 with a relative standard deviation of 2.37%. Possible interferences were tested and evaluated in 5.0 × 10"−"5 mol L"−"1 cadmium (II) in the presence of other inorganic ions. Finally, the proposed method was successfully applied to determine cadmium (II) in seawater and mussel samples. Hence, the satisfactory results confirm the applicability of this sensor in practical analysis. - Highlights: • Synthesis and characterization of new lacunar apatites KPb_4_−_xCa_x(PO_4)_3 (0 ≤ x ≤ 1.5). • Structural refinement of these compounds using Rietveld method. • A study of Ca doping effect in lacunar apatites for detecting Cd (II). • The electrochemical oxidation of Cd (II) was performed at CaLA-CPE using DPASV. • The proposed method was evaluated to detect cadmium in seawater and mussel samples.

  10. Comparative toxicities and synergism of apple orchard pesticides to Apis mellifera (L. and Osmia cornifrons (Radoszkowski.

    Directory of Open Access Journals (Sweden)

    David J Biddinger

    Full Text Available The topical toxicities of five commercial grade pesticides commonly sprayed in apple orchards were estimated on adult worker honey bees, Apis mellifera (L. (Hymenoptera: Apidae and Japanese orchard bees, Osmia cornifrons (Radoszkowski (Hymenoptera: Megachilidae. The pesticides were acetamiprid (Assail 30SG, λ-cyhalothrin (Warrior II, dimethoate (Dimethoate 4EC, phosmet (Imidan 70W, and imidacloprid (Provado 1.6F. At least 5 doses of each chemical, diluted in distilled water, were applied to freshly-eclosed adult bees. Mortality was assessed after 48 hr. Dose-mortality regressions were analyzed by probit analysis to test the hypotheses of parallelism and equality by likelihood ratio tests. For A. mellifera, the decreasing order of toxicity at LD₅₀ was imidacloprid, λ-cyhalothrin, dimethoate, phosmet, and acetamiprid. For O. cornifrons, the decreasing order of toxicity at LD₅₀ was dimethoate, λ-cyhalothrin, imidacloprid, acetamiprid, and phosmet. Interaction of imidacloprid or acetamiprid with the fungicide fenbuconazole (Indar 2F was also tested in a 1∶1 proportion for each species. Estimates of response parameters for each mixture component applied to each species were compared with dose-response data for each mixture in statistical tests of the hypothesis of independent joint action. For each mixture, the interaction of fenbuconazole (a material non-toxic to both species was significant and positive along the entire line for the pesticide. Our results clearly show that responses of A. mellifera cannot be extrapolated to responses of O.cornifrons, and that synergism of neonicotinoid insecticides and fungicides occurs using formulated product in mixtures as they are commonly applied in apple orchards.

  11. Neutron structural studies of La3.5-x-y(Y)yBa3.5-xCa2xCu7Oz (x = y = 0.0 and 0.5) system

    International Nuclear Information System (INIS)

    Subbarao, M.V.; Kulkarni, R.G.; Rajagopal, H.; Sequeira, A.S.

    1997-01-01

    By mixing equal amounts of La 4-x Ca x Ba 3 Cu 7 O z and La 3 Ba 4-x Ca x Cu 7 O z in the proportion of 1 : 1, a series of superconductors part of La replaced by Y with the nominal composition of La 3.5-x-y )(Y) y Ba 3.-5-x Ca 2x Cu 7 O z (LYCP) have been prepared. Two samples with x = y = 0.0 (A) and x = y = 0.5 (B) characterized by x-ray diffraction display tetragonal triple perovskite structure. In order to investigate the effect of substituents (Ca/Y) on structure of this system, neutron diffraction measurements have been carried out at 300 K and λ n =1.216A at Dhruva reactor

  12. A Radiographic Measurement of the Anterior Epidural Space at L4-5 Disc Level.

    Science.gov (United States)

    Xu, Rui-Sheng; Wu, Jie-Shi; Lu, Hai-Dan; Zhu, Hao-Gang; Li, Xia; Dong, Jian; Yuan, Feng-Lai

    2017-05-01

    To observe the morphology character of the anterior epidural space at the L 4-5 disc level and to provide an anatomical basis for safely and accurately performing a percutaneous endoscopic lumbar discectomy (PELD). Fifty-five cases with L 5 S 1 lumbar disc herniation were included in this study, and cases with L 4-5 disease were excluded. When the puncture needle reached the epidural space at the L 5 S 1 level, iohexol was injected at the pressure of 50 cm H 2 O during the PELD, then C-Arm fluoroscopy was used to obtain standard lumbar frontal and lateral images. The widths of epidural space at the level of the L 4 lower endplate, the L 5 upper endplate, as well as the middle point of the L 4-5 disc were measured from the lumbar lateral X-ray film. Epidural space at the L 4-5 disc plane performs like a trapezium chart with a short side at the head end and a long side at the tail end in the lumbar lateral X-ray radiograph, while the average widths of epidural space were 10.2 ± 2.5, 12.3 ± 2.3, and 13.8 ± 2.6 mm at the upper, middle, and lower level of the L 4-5 disc. Understanding the morphological characteristics of epidural space will contribute to improving the safety of the tranforaminal percutaneous endoscopy technique. © 2017 Chinese Orthopaedic Association and John Wiley & Sons Australia, Ltd.

  13. Predominant Api m 10 sensitization as risk factor for treatment failure in honey bee venom immunotherapy.

    Science.gov (United States)

    Frick, Marcel; Fischer, Jörg; Helbling, Arthur; Ruëff, Franziska; Wieczorek, Dorothea; Ollert, Markus; Pfützner, Wolfgang; Müller, Sabine; Huss-Marp, Johannes; Dorn, Britta; Biedermann, Tilo; Lidholm, Jonas; Ruecker, Gerta; Bantleon, Frank; Miehe, Michaela; Spillner, Edzard; Jakob, Thilo

    2016-12-01

    Component resolution recently identified distinct sensitization profiles in honey bee venom (HBV) allergy, some of which were dominated by specific IgE to Api m 3 and/or Api m 10, which have been reported to be underrepresented in therapeutic HBV preparations. We performed a retrospective analysis of component-resolved sensitization profiles in HBV-allergic patients and association with treatment outcome. HBV-allergic patients who had undergone controlled honey bee sting challenge after at least 6 months of HBV immunotherapy (n = 115) were included and classified as responder (n = 79) or treatment failure (n = 36) on the basis of absence or presence of systemic allergic reactions upon sting challenge. IgE reactivity to a panel of HBV allergens was analyzed in sera obtained before immunotherapy and before sting challenge. No differences were observed between responders and nonresponders regarding levels of IgE sensitization to Api m 1, Api m 2, Api m 3, and Api m 5. In contrast, Api m 10 specific IgE was moderately but significantly increased in nonresponders. Predominant Api m 10 sensitization (>50% of specific IgE to HBV) was the best discriminator (specificity, 95%; sensitivity, 25%) with an odds ratio of 8.444 (2.127-33.53; P = .0013) for treatment failure. Some but not all therapeutic HBV preparations displayed a lack of Api m 10, whereas Api m 1 and Api m 3 immunoreactivity was comparable to that of crude HBV. In line with this, significant Api m 10 sIgG 4 induction was observed only in those patients who were treated with HBV in which Api m 10 was detectable. Component-resolved sensitization profiles in HBV allergy suggest predominant IgE sensitization to Api m 10 as a risk factor for treatment failure in HBV immunotherapy. Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.

  14. Toxicity and motor changes in Africanized honey bees (Apis mellifera L.) exposed to fipronil and imidacloprid.

    Science.gov (United States)

    Bovi, Thaís S; Zaluski, Rodrigo; Orsi, Ricardo O

    2018-01-01

    This study evaluated the in vitro toxicity and motor activity changes in African-derived adult honey bees (Apis mellifera L.) exposed to lethal or sublethal doses of the insecticides fipronil and imidacloprid. Mortality of bees was assessed to determine the ingestion and contact lethal dose for 24 h using probit analysis. Motor activities in bees exposed to lethal (LD50) and sublethal doses (1/500th of the lethal dose) of both insecticides were evaluated in a behavioral observation box at 1 and 4 h. Ingestion and contact lethal doses of fipronil were 0.2316 ? 0.0626 and 0.0080 ? 0.0021 μg/bee, respectively. Ingestion and contact lethal doses of imidacloprid were 0.1079 ? 0.0375 and 0.0308 ? 0.0218 μg/bee, respectively. Motor function of bees exposed to lethal doses of fipronil and imidacloprid was impaired; exposure to sublethal doses of fipronil but not imidacloprid impaired motor function. The insecticides evaluated in this study were highly toxic to African-derived A. mellifera and caused impaired motor function in these pollinators.

  15. High linearity 5.2-GHz power amplifier MMIC using CPW structure technology with a linearizer circuit

    International Nuclear Information System (INIS)

    Wu Chiasong; Lin Tah-Yeong; Wu Hsien-Ming

    2010-01-01

    A built-in linearizer was applied to improve the linearity in a 5.2-GHz power amplifier microwave monolithic integrated circuit (MMIC), which was undertaken with 0.15-μm AlGaAs/InGaAs D-mode PHEMT technology. The power amplifier (PA) was studied taking into account the linearizer circuit and the coplanar waveguide (CPW) structures. Based on these technologies, the power amplifier, which has a chip size of 1.44 x 1.10 mm 2 , obtained an output power of 13.3 dBm and a power gain of 14 dB in the saturation region. An input third-order intercept point (HP 3 ) of -3 dBm, an output third-order intercept point (OIP 3 ) of 21.1 dBm and a power added efficiency (PAE) of 22% were attained, respectively. Finally, the overall power characterization exhibited high gain and high linearity, which illustrates that the power amplifier has a compact circuit size and exhibits favorable RF characteristics. This power circuit demonstrated high RF characterization and could be used for microwave power circuit applications at 5.2 GHz. (semiconductor integrated circuits)

  16. Recenzija. Monografija apie filosofijos ir literatūros giminystę

    Directory of Open Access Journals (Sweden)

    Tomas Kačerauskas

    2011-04-01

    Full Text Available Prieš keletą metų neoficialiame pokalbyje J. Baranova prasitarė, kad nėra didesnio malonumo už rašymą. Tiesą sakant, buvau sužavėtas ir priblokštas ne tik dėl šios ištaros asimetrijos R. Barthes’o minčiai apie skaitymo malonumą (net erotinį. Visai kitaip apie rašymą atsiliepia A. Šliogeris (kurio filosofi jos apmąstymui J. Baranova pelnytai skiria daug dėmesio: jis mieliau nerašytų nei rašytų. Tokiais atvejais prisimenu M. Bulgakovą, kuris „tempiąs save už plaukų prie rašomojo stalo“. Rašymas daug kam siejasi su disciplina, prievarta savęs atžvilgiu, geriausiu atveju – kasdieniu įpročiu.

  17. Tactile learning and the individual evaluation of the reward in honey bees (Apis mellifera L.).

    Science.gov (United States)

    Scheiner, R; Erber, J; Page, R E

    1999-07-01

    Using the proboscis extension response we conditioned pollen and nectar foragers of the honey bee (Apis mellifera L.) to tactile patterns under laboratory conditions. Pollen foragers demonstrated better acquisition, extinction, and reversal learning than nectar foragers. We tested whether the known differences in response thresholds to sucrose between pollen and nectar foragers could explain the observed differences in learning and found that nectar foragers with low response thresholds performed better during acquisition and extinction than ones with higher thresholds. Conditioning pollen and nectar foragers with similar response thresholds did not yield differences in their learning performance. These results suggest that differences in the learning performance of pollen and nectar foragers are a consequence of differences in their perception of sucrose. Furthermore, we analysed the effect which the perception of sucrose reward has on associative learning. Nectar foragers with uniform low response thresholds were conditioned using varying concentrations of sucrose. We found significant positive correlations between the concentrations of the sucrose rewards and the performance during acquisition and extinction. The results are summarised in a model which describes the relationships between learning performance, response threshold to sucrose, concentration of sucrose and the number of rewards.

  18. Origin of honeybees (Apis mellifera L.) from the Yucatan peninsula inferred from mitochondrial DNA analysis.

    Science.gov (United States)

    Clarke, K E; Oldroyd, B P; Javier, J; Quezada-Euán, G; Rinderer, T E

    2001-06-01

    Honeybees (Apis mellifera L.) sampled at sites in Europe, Africa and South America were analysed using a mitochondrial DNA restriction fragment length polymorphism (RFLP) marker. These samples were used to provide baseline information for a detailed analysis of the process of Africanization of bees from the neotropical Yucatan peninsula of Mexico. Radical changes in mitochondrial haplotype (mitotype) frequencies were found to have occurred in the 13-year period studied. Prior to the arrival of Africanized bees (1986) the original inhabitants of the Yucatan peninsula appear to have been essentially of southeastern European origin with a smaller proportion having northwestern European ancestry. Three years after the migration of Africanized bees into the area (1989), only very low levels of maternal gene flow from Africanized populations into the resident European populations had occurred. By 1998, however, there was a sizeable increase in the proportion of African mitotypes in domestic populations (61%) with feral populations having 87% of mitotypes classified as African derived. The results suggest that the early stages of Africanization did not involve a rapid replacement of European with African mitotypes and that earlier studies probably overestimated the prevalence of African mitotypes.

  19. Slow strain rate corrosion and fracture characteristics of X-52 and X-70 pipeline steels

    International Nuclear Information System (INIS)

    Contreras, A.; Albiter, A.; Salazar, M.; Perez, R.

    2005-01-01

    The susceptibility to stress corrosion cracking (SCC) in a NACE solution saturated with H 2 S, of the X-52 and X-70 steels was studied using slow strain rate tests (SSRT) and electrochemical evaluations. SCC tests were performed in samples which include the longitudinal weld bead of the pipeline steels and were carried out in the NACE solution at both room temperature and 50 deg. C. After failure, the fracture surfaces were observed in a scanning electron microscope (SEM) and the chemical analysis were obtained using X-rays energy dispersive (EDXs) techniques. The specimens tested in air, exhibited a ductile type of failure, and whereas, those tested in the corrosive solution showed a brittle fracture. Specimens tested in the NACE solution saturated with H 2 S presented high susceptibility to SCC. Corrosion was found to be an important factor in the initiation of some cracks. In addition, the effect of the temperature on the corrosion attack was explored. The susceptibility to SCC was manifested as a decrease in the mechanical properties. Potentiodynamic polarization curves and hydrogen permeation measurements were made. The diffusion of atomic hydrogen was related to this fracture forms. The hydrogen permeation flux increased with the increasing of temperature

  20. Estudio in vitro de la citotoxicidad y genotoxicidad de los productos liberados del acero inoxidable 316L con recubrimientos cerámicos bioactivos Cytotoxic and genotoxic study of in Vitro released products of stainless Steel 316l with bioactive ceramic Coatings

    Directory of Open Access Journals (Sweden)

    María Elena Márquez Fernández

    2007-03-01

    Full Text Available El acero inoxidable AISI 316L es el biomaterial mas utilizado para la fabricación de implantes temporales, pero presenta limitaciones para implantes permanentes debido a la liberación de iones metálicos hacia los tejidos circundantes, produciendo especies reactivas de oxígeno (ERO y daño en ADN, factores que aumentan el riesgo de aparición de tumores locales y fallas mecánicas del implante. Una estrategia utilizada para disminuir la liberación de iones es la modificación superficial de los implantes metálicos por medio de recubrimientos inorgánicos, cerámicos o vítreos, aplicados por el método sol-gel, el cual presenta una serie de ventajas comparativas con otras técnicas de deposición, como buena adherencia, aplicación sencilla, mínimos problemas de secado, bajas temperaturas de densificación y posibilidad de agregar partículas y/o grupos orgánicos que mejoran la adherencia celular al implante aumentando su biocompatibilidad. En el presente trabajo se evaluaron los efectos citotóxico por medio de la técnica MTT, y genotóxico por electroforesis en gel de células individuales (Ensayo Cometa, sobre células de la línea celular CHO, de los productos liberados en medio MEM por el acero inoxidable 316L sin recubrir, recubierto con una monocapa de vidrio de sílice (MC, o con doble capa que contiene partículas bioactivas de hidroxiapatita (HA, vidrio (V o vitrocerámico (VC, después de un periodo de 30 días. Los resultados muestran que a los 30 días de envejecimiento en medio MEM no se encuentra ningún efecto citotóxico, pero se encontró efecto genotóxico en las probetas de A y MC que no representa un peligro inminente a sistemas celulares. The stainless steel AISI 316L is the must used biomaterial for the making of temporal prosthesis, but it presents severe limitations for permanent implants due to the generation and migration of metallic ions to the surrounding peripheral tissues, which produces oxygen reactive

  1. Osmotic concentration in three races of honey bee, Apis mellifera L. under environmental conditions of arid zone.

    Science.gov (United States)

    Ali, Hussain; Alqarni, Abdulaziz S; Owayss, Ayman A; Hassan, Awad M; Smith, Brian H

    2017-07-01

    Hemolymph osmolarity has great effect on honey bee health, especially in arid and semi-arid zones. It regulates water and nutrients in stressed tissues. Osmotic concentration in three races ( Apis mellifera ligustica , A. m. carnica and A. m. jemenitica ) of Apis mellifera was tested in central Saudi Arabia during spring and summer seasons in 2015. Newly emerged bee workers were first marked and later their hemolymph was extracted after intervals of 1, 5, 10, 15, 20 and 25 days. A significant positive correlation between age and osmolarity was found in all three races during spring and summer seasons. The lowest combined osmotic concentration for all three races was found after 1 day interval, while the highest osmotic concentration was recorded after 25 days. Among all races, A. m. ligustica showed significantly high osmotic concentration after 25 days in spring and summer seasons as compared to the other two races. Only A. m. jemenitica showed similar osmotic concentration after 10 and 15 days in both spring and summer seasons compared to other two races. Mean osmotic concentration of all three races was significantly different after 20 and 25 days in spring and summer seasons. Overall mean recorded during summer was significantly higher than the mean of spring season. Combined osmotic concentration in young drones of all races was significantly lower than that of old drones during spring and summer seasons.

  2. Produção e desenvolvimento de colônias de abelhas africanizadas (Apis mellifera l. a partir de diferentes áreas e idades de cria Production and development of africanized honey bee (Apis mellifera l. colonies departing from different comb brood areas and brood ages

    Directory of Open Access Journals (Sweden)

    Roberto Henrique Dias da Silva

    2004-04-01

    Full Text Available A apicultura brasileira usa da captura de enxames silvestres de abelhas melíferas africanizadas (Apis mellifera L. para repor e/ou aumentar o número de colônias dos apiários, possuindo inconvenientes como a dependência da natureza para captura dos enxames, a heterogeneidade genética das colônias capturadas e a possibilidade desses enxames serem portadores de doenças e parasitas prejudiciais à sanidade das abelhas. O presente trabalho testa e apresenta uma técnica de divisão de colônias de abelhas melíferas africanizadas para a produção de novas colônias fortes em curto espaço de tempo, a partir de recursos mínimos de cera, cria e alimento. Os resultados mostraram que núcleos de A. mellifera formados inicialmente com uma rainha jovem e fecundada, 1 kg de operárias, um quadro de cria fechada, um quadro de favo puxado e vazio e dois quadros com cera alveolada permitem a produção de novas colônias em 42 dias. Portanto, pode-se concluir que a técnica de divisão de colônias por formação de núcleos como descrito acima, oferece aos apicultores uma alternativa viável para a produção e comercialização em larga escala de novas colônias de abelhas melíferas africanizadas.The Brazilian apiculture relies upon collecting wild swarms of Africanized honey bees (Apis mellifera L. to replace and/or increase the number of colonies in the apiaries. This practice brings problems such as dependence on nature to capture any swarm, diverse genetic make-up of the colonies captured and the possibility of these swarms be carrying diseases and parasites harmful to the bees. The present work tests and presents a technique to split colonies of Africanized honey bees to produce new strong colonies in short time, departing from little resources of wax, brood and food stores. Results showed that A. mellifera nuclei formed by a young and mated queen, 1kg of workers, a frame of sealed brood, an empty frame of drawn beeswax and two frames

  3. L X-ray emission induced by heavy ions

    Energy Technology Data Exchange (ETDEWEB)

    Pajek, M. [Institute of Physics, Jan Kochanowski University, 25-406 Kielce (Poland); Banaś, D., E-mail: d.banas@ujk.edu.pl [Institute of Physics, Jan Kochanowski University, 25-406 Kielce (Poland); Braziewicz, J.; Majewska, U.; Semaniak, J. [Institute of Physics, Jan Kochanowski University, 25-406 Kielce (Poland); Fijał-Kirejczyk, I. [The Institute of Atomic Energy, 05-400 Otwock-Świerk (Poland); Jaskóła, M.; Czarnacki, W.; Korman, A. [The National Centre for Nuclear Research, 05-400 Otwock-Świerk (Poland); Kretschmer, W. [Physikalisches Institut, Universität Erlangen-Nürnberg, D-91058 Erlangen (Germany); Mukoyama, T. [Institute for Nuclear Research, Hungarian Academy of Sciences (ATOMKI), H-4026 Debrecen (Hungary); Trautmann, D. [Institut für Physik, Universität Basel, Basel (Switzerland)

    2015-11-15

    Particle-induced X-ray emission (PIXE) technique is usually applied using typically 1 MeV to 3 MeV protons or helium ions, for which the ion-atom interaction is dominated by the single ionization process. For heavier ions the multiple ionization plays an increasingly important role and this process can influence substantially both the X-ray spectra and atomic decay rates. Additionally, the subshell coupling effects are important for the L- and M-shells ionized by heavy ions. Here we discuss the main features of the X-ray emission induced by heavy ions which are important for PIXE applications, namely, the effects of X-ray line shifts and broadening, vacancy rearrangement and change of the fluorescence and Coster–Kronig yields in multiple ionized atoms. These effects are illustrated here by the results of the measurements of L X-ray emission from heavy atoms bombarded by 6 MeV to 36 MeV Si ions, which were reported earlier. The strong L-subshell coupling effects are observed, in particular L{sub 2}-subshell, which can be accounted for within the coupling subshell model (CSM) developed within the semiclassical approximation. Finally, the prospects to use heavy ions in PIXE analysis are discussed.

  4. Enersave API: Android-based power-saving framework for mobile devices

    Directory of Open Access Journals (Sweden)

    A.M. Muharum

    2017-06-01

    Full Text Available Power consumption is a major factor to be taken into consideration when using mobile devices in the IoT field. Good Power management requires proper understanding of the way in which it is being consumed by the end-devices. This paper is a continuation of the work in Ref. [1] and proposes an energy saving API for the Android Operating System in order to help developers turn their applications into energy-aware ones. The main features heavily used for building smart applications, greatly impact battery life of Android devices and which have been taken into consideration are: Screen brightness, Colour scheme, CPU frequency, 2G/3G network, Maps, Low power localisation, Bluetooth and Wi-Fi. The assessment of the power-saving API has been performed on real Android devices and also compared to the most powerful power-saving applications – DU Battery Saver and Battery Saver 2016 – currently available on the Android market. Comparisons demonstrate that the Enersave API has a significant impact on power saving when incorporated in android applications. While DU Battery Saver and Battery Saver 2016 help saving 22.2% and 40.5% of the battery power respectively, the incorporation of the Enersave API in android applications can help save 84.6% of battery power.

  5. Ecuaciones constitutivas de la fluencia en caliente de aceros microaleados

    Directory of Open Access Journals (Sweden)

    Cabrera, J. M.

    1998-05-01

    Full Text Available Over centuries, the hot forming has been employed to provide shape to metáis. Nowadays, the deformation at high temperatures gives also the required final mechanical properties. From this point of view, the obtention of a constitutive equation describing the hot flow behaviour of microalloyed steels in particular is a very important task. The main difficulty in modelling the high temperature flow arises from the simultaneity of two opposite phenomena, namely, work hardening and dynamic softening due to recovery and recrystallization. In this is work a review of constitutive equations (including the effect of the chemical composition describing the flow behaviour of microalloyed steels deformed under high temperature conditions.

    Durante siglos el conformado en caliente se ha utilizado para proporcionar a los metales la forma deseada. Hoy en día la deformación en caliente no sólo genera la geometría deseada sino las características mecánicas requeridas. Así, la obtención de una ecuación constitutiva para la fluencia en caliente de un acero en particular, es una tarea ineludible para efectuar simulaciones por ordenador de procesos industriales. La complicación de la modelización de la fluencia a alta temperatura proviene de la simultaneidad de dos fenómenos contrapuestos durante la deformación, a saber, endurecimiento por deformación y ablandamiento por recuperación de la estructura. Este último a su vez puede constar de restauración y recristalización dinámicas. En este trabajo se revisan y plantean las ecuaciones constitutivas que describen las curvas de fluencia bajo condiciones de deformación en caliente, y se presenta una aplicación de las mismas a aceros microaleados.

  6. 48 CFR 52.212-5 - Contract Terms and Conditions Required To Implement Statutes or Executive Orders-Commercial Items.

    Science.gov (United States)

    2010-10-01

    ... Ethics and Conduct (APR 2010)(Pub. L. 110-252, Title VI, Chapter 1 (41 U.S.C. 251 note)). ___(3) 52.203....S.C. 3301 note). ___(35) 52.225-13, Restrictions on Certain Foreign Purchases (JUN 2008) (E.O.'s.... 5150). ___(38) 52.232-29, Terms for Financing of Purchases of Commercial Items (FEB 2002) (41 U.S.C...

  7. Comparing the UK EQ-5D-3L and English EQ-5D-5L Value Sets.

    Science.gov (United States)

    Mulhern, Brendan; Feng, Yan; Shah, Koonal; Janssen, Mathieu F; Herdman, Michael; van Hout, Ben; Devlin, Nancy

    2018-06-01

    Three EQ-5D value sets (EQ-5D-3L, crosswalk, and EQ-5D-5L) are now available for cost-utility analysis in the UK and/or England. The value sets' characteristics differ, and it is important to assess the implications of these differences. The aim of this paper is to compare the three value sets. We carried out analysis comparing the predicted values from each value set, and investigated how differences in health on the descriptive system is reflected in the utility score by assessing the value of adjacent states. We also assessed differences in values using data from patients who completed both EQ-5D-3L and EQ-5D-5L. The distribution of the value sets systematically differed. EQ-5D-5L values were higher than EQ-5D-3L/crosswalk values. The overall range and difference between adjacent states was smaller. In the patient data, the EQ-5D-5L produced higher values across all conditions and there was some evidence that the value sets rank different health conditions in a similar severity order. There are important differences between the value sets. Due to the smaller range of EQ-5D-5L values, the possible change in quality-adjusted life years (QALYs) might be reduced, but they will apply to both control and intervention groups, and will depend on whether the gain is in quality of life, survival, or both. The increased sensitivity of EQ-5D-5L may also favour QALY gains even if the changes in utility are smaller. Further work should assess the impact of the different value sets on cost effectiveness by repeating the analysis on clinical trial data.

  8. Effect of entomopathogens on Africanized Apis mellifera L. (Hymenoptera: Apidae

    Directory of Open Access Journals (Sweden)

    Michele Potrich

    2018-01-01

    Full Text Available This study aimed to evaluate the effect of commercially used entomopathogens on Africanized Apis mellifera L. (Hymenoptera: Apidae. Four bioassays were performed: 1 pulverized entomopathogens on A. mellifera; 2 entomopathogens sprayed on a smooth surface; 3 entomopathogens sprayed on soy leaves; and 4 entomopathogens mixed with candy paste (sugar syrup. Five treatments were prepared: sterile distilled water (control, distilled water sterilized with Tween® 80 (0.01%, and the commercial entomopathogens Metarhizium anisopliae E9 (1.0 × 109 conidia mL−1, Beauveria bassiana PL63 (1.0 × 108 conidia mL−1 and Bacillus thuringiensis var. kurstaki HD-1 (3.0 × 108 spores mL−1. Each treatment consisted of five repetitions, with 20 workers per repetition, which were stored in a plastic box and, later, in a biological oxygen demand (B.O.D. incubator (27 ± 2 °C, RH of 60% ± 10%, 12-h photophase. The mortality of the workers was evaluated from 1 h to 240 h, and the data were analyzed using Bayesian inference. The workers killed by the ingestion of candy paste contaminated with the pathogens (products were randomly separated and selected for the removal of the midgut. Each midgut was fixed in Bouin's solution and prepared for histology. B. bassiana was verified to reduce the survival of A. mellifera workers in all bioassays. Moreover, M. anisopliae reduced the survival of A. mellifera workers directly sprayed, on a smooth surface and mixed with candy. B. thuringiensis reduced A. mellifera survival on a smooth surface and mixed with candy paste. However, its effects were lower than that observed by B. bassiana. The treatments with the biological products did not induce morphometric alterations in the midgut of A. mellifera. Keywords: Bayesian statistics, Entomopathogenic fungi, Entomopathogenic bacteria, Honeybee, Selectivity

  9. Evaluation of the convolution sum involving the sum of divisors function for 22, 44 and 52