Preliminary analysis of accidents on the Santa QuitÉria Project: occupationally exposed individuals

Energy Technology Data Exchange (ETDEWEB)

Anjos, Gullit Diego C. dos, E-mail: gullitcardoso@inb.gov.br [Indústrias Nucleares do Brasil (INB), Rio de Janeiro, RJ (Brazil)

2017-07-01

The Santa Quitéria Project (PSQ) is an enterprise that aims at the production of phosphate compounds as main products, and of uranium concentrates as by-products from minerals of the Itataia deposit. The intended area for implementation of the project is located in the municipality of Santa Quitéria, north central region of the State of Ceará. The U.S. Nuclear Regulatory Commission lists the basic design accidents for a Uranium Processing Plant, such as the PSQ. Among all these scenarios, fire in uranium extraction cells was the one with the highest doses released. For simulation of the fire event, the atmospheric dispersion model used was the standard Gaussian plume model. The doses were calculated for two sets of meteorological conditions: stability class F, with wind velocity of 1 m/s and class D stability with wind velocity of 4.5 m/s. For PSQ, it was considered that there will be no public individual until after 2000 meters from the release point. The doses corresponding to the occupationally exposed individuals are: 2.0E-3 mSv (class D) and 5 mSv (Class F), 300 meters away from the event. Analyzing the results, it can be concluded that there are no significant radiological consequences for the occupationally exposed individual, both in the stability class D and the F. The doses of the workers are well below the levels that could cause deterministic effects. Even if an occupationally exposed individual were exposed for 12 hours in the center of the plume, the dose received would not exceed the annual limit established by CNEN. (author)

Response of HEPA filters to simulated-accident conditions

International Nuclear Information System (INIS)

Gregory, W.S.; Martin, R.A.; Smith, P.R.; Fenton, D.E.

1982-01-01

High-efficiency particulate air (HEPA) filters have been subjected to simulated accident conditions to determine their response to abnormal operating events. Both domestic and European standard and high-capacity filters have been evaluated to determine their response to simulated fire, explosion, and tornado conditions. The HEPA filter structural limitations for tornado and explosive loadings are discussed. In addition, filtration efficiencies during these accident conditions are reported for the first time. Our data indicate efficiencies between 80% and 90% for shock loadings below the structural limit level. We describe two types of testing for ineffective filtration - clean filters exposed to pulse-entrained aerosol and dirty filters exposed to tornado and shock pulses. Efficiency and material loss data are described. Also, the resonse of standard HEPA filters to simulated fire conditions is presented. We describe a unique method of measuring accumulated combustion products on the filter. Additionally, data relating to pressure drop vs accumulated mass during plugging are reported for simulated combustion aerosols. The effects of concentration and moisture levels on filter plugging were evaluated. We are obtaining all of the above data so that mathematical models can be developed for fire, explosion, and tornado accident analysis computer codes. These computer codes can be used to assess the response of nuclear air cleaning systems to accident conditions

The accidents during shutdown conditions Temelin NPP

International Nuclear Information System (INIS)

Sykora, M.; Mlady, O.

1996-01-01

Two parallel activities oriented for the accidents during shutdown conditions are performed at Temelin NPP: Development of symptom based emergency operating procedures (EOPs) applicable for the accidents which could occur during operational modes 1 through 4; independent evaluation of plant safety as part of the Temelin Shutdown probabilistic assessment to define the accidents which could occur during mode 5 and 6 for which the EOPs must be extended. Both these activities are in progress now because Temelin plant is still in the construction phase

Shipping container response to severe highway and railway accident conditions: Main report

International Nuclear Information System (INIS)

Fischer, L.E.; Chou, C.K.; Gerhard, M.A.; Kimura, C.Y.; Martin, R.W.; Mensing, R.W.; Mount, M.E.; Witte, M.C.

1987-02-01

This report describes a study performed by the Lawrence Livermore National Laboratory to evaluate the level of safety provided under severe accident conditions during the shipment of spent fuel from nuclear power reactors. The evaluation is performed using data from real accident histories and using representative truck and rail cask models that likely meet 10 CFR 71 regulations. The responses of the representative casks are calculated for structural and thermal loads generated by severe highway and railway accident conditions. The cask responses are compared with those responses calculated for the 10 CFR 71 hypothetical accident conditions. By comparing the responses it is determined that most highway and railway accident conditions fall within the 10 CFR 71 hypothetical accident conditions. For those accidents that have higher responses, the probabilities anf potential radiation exposures of the accidents are compared with those identified by the assessments made in the ''Final Environmental Statement on the Transportation of Radioactive Material by Air and other Modes,'' NUREG-0170. Based on this comparison, it is concluded that the radiological risks from spent fuel under severe highway and railway accident conditions as derived in this study are less than risks previously estimated in the NUREG-0170 document

ACCOUNT OF ROAD CONDITIONS WHILE INVESTIGATING TRAFFIC ACCIDENTS

Directory of Open Access Journals (Sweden)

D. D. Selioukov

2010-01-01

Full Text Available The paper considers problems on better traffic safety at government, authority, engineering and driver activity levels, account of road conditions while investigating traffic accidents. The paper also provides road defects mentioned in forensic transport examinations of traffic accidents.

RIA Fuel Codes Benchmark - Volume 1

International Nuclear Information System (INIS)

Marchand, Olivier; Georgenthum, Vincent; Petit, Marc; Udagawa, Yutaka; Nagase, Fumihisa; Sugiyama, Tomoyuki; Arffman, Asko; Cherubini, Marco; Dostal, Martin; Klouzal, Jan; Geelhood, Kenneth; Gorzel, Andreas; Holt, Lars; Jernkvist, Lars Olof; Khvostov, Grigori; Maertens, Dietmar; Spykman, Gerold; Nakajima, Tetsuo; Nechaeva, Olga; Panka, Istvan; Rey Gayo, Jose M.; Sagrado Garcia, Inmaculada C.; Shin, An-Dong; Sonnenburg, Heinz Guenther; Umidova, Zeynab; Zhang, Jinzhao; Voglewede, John

2013-01-01

Reactivity-initiated accident (RIA) fuel rod codes have been developed for a significant period of time and they all have shown their ability to reproduce some experimental results with a certain degree of adequacy. However, they sometimes rely on different specific modelling assumptions the influence of which on the final results of the calculations is difficult to evaluate. The NEA Working Group on Fuel Safety (WGFS) is tasked with advancing the understanding of fuel safety issues by assessing the technical basis for current safety criteria and their applicability to high burnup and to new fuel designs and materials. The group aims at facilitating international convergence in this area, including the review of experimental approaches as well as the interpretation and use of experimental data relevant for safety. As a contribution to this task, WGFS conducted a RIA code benchmark based on RIA tests performed in the Nuclear Safety Research Reactor in Tokai, Japan and tests performed or planned in CABRI reactor in Cadarache, France. Emphasis was on assessment of different modelling options for RIA fuel rod codes in terms of reproducing experimental results as well as extrapolating to typical reactor conditions. This report provides a summary of the results of this task. (authors)

Behaviour of molten reactor fuels under accident conditions

International Nuclear Information System (INIS)

Xavier Swamikannu, A.; Mathews, C.K.

1980-01-01

The behaviour of molten reactor fuels under accident conditions has received considerable importance in recent times. The chemical processes that occur in the molten state among the fuel, the clad components and the concrete of the containment building under the conditions of a core melt down accident in oxide fuelled reactors have been reviewed with the purpose of identifying areas of developmental work required to be performed to assess and minimize the consequences of such an accident. This includes the computation and estimation of vapour pressure of various gaseous species over the fuel, the clad and the coolant, providing of sacrificial materials in the concrete in order to protect the containment building in order to prevent release of radioactive gases into the atmosphere and understanding the distribution and chemical state of fission products in the molten fuel in order to provide for the effective removal of their decay heats. (auth.)

Aspects of using a best-estimate approach for VVER safety analysis in reactivity initiated accidents

Energy Technology Data Exchange (ETDEWEB)

Ovdiienko, Iurii; Bilodid, Yevgen; Ieremenko, Maksym [State Scientific and Technical Centre on Nuclear and Radiation, Safety (SSTC N and RS), Kyiv (Ukraine); Loetsch, Thomas [TUEV SUED Industrie Service GmbH, Energie und Systeme, Muenchen (Germany)

2016-09-15

At present time, Ukraine faces the problem of small margins of acceptance criteria in connection with the implementation of a conservative approach for safety evaluations. The problem is particularly topical conducting feasibility analysis of power up-rating for Ukrainian nuclear power plants. Such situation requires the implementation of a best-estimate approach on the basis of an uncertainty analysis. For some kind of accidents, such as loss-of-coolant accident (LOCA), the best estimate approach is, more or less, developed and established. However, for reactivity initiated accident (RIA) analysis an application of best estimate method could be problematical. A regulatory document in Ukraine defines a nomenclature of neutronics calculations and so called ''generic safety parameters'' which should be used as boundary conditions for all VVER-1000 (V-320) reactors in RIA analysis. In this paper the ideas of uncertainty evaluations of generic safety parameters in RIA analysis in connection with the use of the 3D neutron kinetic code DYN3D and the GRS SUSA approach are presented.

OCCUPATIONAL ACCIDENTS AS INDICATORS OF INADEQUATE WORK CONDITIONS AND WORK ENVIRONMENT

OpenAIRE

Petar Babović

2009-01-01

Occupational accidents due to inadequate working conditions and work environment present a major problem in highly industrialised countries, as well as in developing ones. Occupational accidents are a regular and accompanying phenomenon in all human activities and one of the main health related and economic problems in modern societies.The aim of this study is the analysis of the connections of unfavourable working conditions and working environment on occupational accidents. Occurrence of oc...

Preliminary analysis of accidents of the Santa QuitÉRia Project: gaussian methodology for atmospheric dispersion

Energy Technology Data Exchange (ETDEWEB)

Anjos, Gullit Diego C. dos, E-mail: gullitcardoso@inb.gov.br [Indústrias Nucleares do Brasil (INB), Rio de Janeiro, RJ (Brazil)

2017-07-01

The Santa Quitéria Project (PSQ) is an enterprise that aims at the production of phosphate compounds as main products, and of uranium concentrates as by-products, from the minerals of the Itataia deposit. The intended area for implementation of the project is located in the municipality of Santa Quitéria, north central region of the State of Ceará. The U.S. Nuclear Regulatory Commission, lists the basic design accidents for a Uranium Processing Plant, such as the PSQ. Among all these scenarios,fire in uranium extraction cells was the one with the highest doses released. For simulation of the fire event, the atmospheric dispersion model used was the standard Gaussian plume model. The doses were calculated for two sets of meteorological conditions: stability class F, with wind velocity of 1 m/s and class D stability with wind velocity of 4.5 m/s. For PSQ, it was considered that there will be no public individual until after 2000 meters from the release point. The doses corresponding to the Occupationally exposed individuals are: 2.0E-3 mSv (class D) and 5 mSv (Class F), 300 meters away from the event. Analyzing the results, it can be concluded that there are no significant radiological consequences for the occupationally exposed individual, both in the stability class D and the F. For PSQ, it was considered that there will be no public individual until after 2000 meters from the release point. The doses, in mSv, corresponding to the individuals located near the project are: Morrinhos (1.27E-03 mSv - Class D and 3.92E-02 - Class F); Burned (1.41E-03 mSv - Class D and 4.28E-02 - Class F); Lagoa do Mato (<7.94E-04 mSv - Class D and <2.68E-02 mv - Class F). (author)

Preliminary analysis of accidents of the Santa QuitÉRia Project: gaussian methodology for atmospheric dispersion

International Nuclear Information System (INIS)

Anjos, Gullit Diego C. dos

2017-01-01

The Santa Quitéria Project (PSQ) is an enterprise that aims at the production of phosphate compounds as main products, and of uranium concentrates as by-products, from the minerals of the Itataia deposit. The intended area for implementation of the project is located in the municipality of Santa Quitéria, north central region of the State of Ceará. The U.S. Nuclear Regulatory Commission, lists the basic design accidents for a Uranium Processing Plant, such as the PSQ. Among all these scenarios,fire in uranium extraction cells was the one with the highest doses released. For simulation of the fire event, the atmospheric dispersion model used was the standard Gaussian plume model. The doses were calculated for two sets of meteorological conditions: stability class F, with wind velocity of 1 m/s and class D stability with wind velocity of 4.5 m/s. For PSQ, it was considered that there will be no public individual until after 2000 meters from the release point. The doses corresponding to the Occupationally exposed individuals are: 2.0E-3 mSv (class D) and 5 mSv (Class F), 300 meters away from the event. Analyzing the results, it can be concluded that there are no significant radiological consequences for the occupationally exposed individual, both in the stability class D and the F. For PSQ, it was considered that there will be no public individual until after 2000 meters from the release point. The doses, in mSv, corresponding to the individuals located near the project are: Morrinhos (1.27E-03 mSv - Class D and 3.92E-02 - Class F); Burned (1.41E-03 mSv - Class D and 4.28E-02 - Class F); Lagoa do Mato (<7.94E-04 mSv - Class D and <2.68E-02 mv - Class F). (author)

Nuclear Fuel Behaviour during Reactivity Initiated Accidents. Workshop Proceedings

International Nuclear Information System (INIS)

2010-01-01

A reactivity initiated accident (RIA) is a nuclear reactor accident that involves an unwanted increase in fission rate and reactor power. The power increase may damage the reactor core. The main objective of the workshop was to review the current status of the experimental and analytical studies of the fuel behavior during the RIA transients in PWR and BWR reactors and the acceptance criteria for RIA in use and under consideration. The workshop was organized in an opening session and 5 technical sessions: 1) Recent experimental results and experimental techniques used; 2) Modelling and Data Interpretation; 3) Code Assessment; 4) RIA Core Analysis and 5) Revision and application of safety criteria

Radionuclides release possibility analysis of MSR at various accident conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, Choong Wie; Kim, Hee Reyoung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

There are some accidents which go beyond our expectation such as Fukushima Daiichi nuclear disaster and amounts of radionuclides release to environment, so more effort and research are conducted to prevent it. MSR (Molten Salt Reactor) is one of GEN-IV reactor types, and its coolant and fuel are mixtures of molten salt. MSR has a schematic like figure 1 and it has different features with the solid fuel reactor, but most important and interesting feature of MSR is its many safety systems. For example, MSR has a large negative void coefficient. Even though power increases, the reactor slows down soon. Radionuclides release possibility of MSR was analyzed at various accident conditions including Chernobyl and Fukushima ones. The MSR was understood to prevent the severe accident by the negative reactivity coefficient and the absence of explosive material such as water at the Chernobyl disaster condition. It was expected to contain fuel salts in the reactor building and not to release radionuclides into environment even if the primary system could be ruptured or broken and fuel salts would be leaked at the Fukushima Daiichi nuclear disaster condition of earthquake and tsunami. The MSR, which would not lead to the severe accident and therefore prevents the fuel release to the environment at many expected scenarios, was thought to have priority in the aspect of accidents. A quantitative analysis and a further research are needed to evaluate the possibility of radionuclide release to the environment at the various accident conditions based on the simple comparison of the safety feature between MSR and solid fuel reactor.

Review of RIA and LOCA criteria for WWER fuel

International Nuclear Information System (INIS)

Hozer, Z.

2006-01-01

The RIA and LOCA fuel safety criteria are under revision in the international community of fuel suppliers, authorities and research organizations. The main criteria will be reviewed in the paper for WWER fuel. Experimental data on the fuel failure behaviour under reactivity-initiated accident (RIA) conditions produced in the last decade in French and Japanese test reactors indicated low failure enthalpy for high burnup fuel compared to fresh fuel. However the high burnup was not the only phenomenon influencing the fuel failure. The oxide scale on the external surface of the fuel rod, hydrogen content of the Zr cladding and the local hydriding seemed also be responsible for the failure at low enthalpy. Furthermore differences have been found between Western design fuel and Russian type WWER fuel. The burnup dependence of fuel failure for WWER fuel was found much less, probably due to the low oxidation during normal operational conditions compared to other PWRs. The recently published Vitanza and KAERI correlations for RIA failure enthalpy have been applied to 23 WWER tests. Experimental data from Russian IGR and BIGR reactors have been used. The calculations have shown that both burnup and cladding oxidation effects must be considered, however the pulse width dependence of failure enthalpy has not been confirmed. During loss of coolant accidents (LOCA) the peak cladding temperature and local oxidation criteria have to be met. The oxidation criterion is under discussion today in many laboratories. The AEKI carried out several experimental series with Zr1%Nb cladding used in WWER reactors. The paper will describe the main results of the tests and present the limit for ductile-brittle transition derived from ring compression test. The behaviour of Zr1%Nb (E110) and Zircaloy-4 claddings under LOCA conditions will be compared as well. (author)

Proceedings of the topical meeting on reactivity initiated accidents (RIA)

International Nuclear Information System (INIS)

2003-01-01

The topical meeting was devoted to RIA fuel acceptance criteria, in particular to the fuel fragmentation enthalpy limit and the PCMI failure enthalpy limit in relation to high burnup fuel. In total 50 participants attended. Research and industry organisations from France, Finland, Germany, Hungary, Japan, the Russian Federation, Sweden, the United Kingdom and the USA including the Swiss regulatory body, HSK, and the Halden reactor project, presented 16 papers in all. The papers covered three main areas: 'best estimate' core calculations for RIA energy deposition in high burnup fuels, the technical background of current and new RIA fuel safety criteria, and ongoing RIA experimental programmes. A number of open issues were identified, whose resolution is expected from ongoing and planned national and international experimental programmes

10 CFR 71.74 - Accident conditions for air transport of plutonium.

Science.gov (United States)

2010-01-01

... 10 Energy 2 2010-01-01 2010-01-01 false Accident conditions for air transport of plutonium. 71.74 Section 71.74 Energy NUCLEAR REGULATORY COMMISSION (CONTINUED) PACKAGING AND TRANSPORTATION OF RADIOACTIVE MATERIAL Package, Special Form, and LSA-III Tests 2 § 71.74 Accident conditions for air transport of...

Full-length fuel rod behavior under severe accident conditions

International Nuclear Information System (INIS)

Lombardo, N.J.; Lanning, D.D.; Panisko, F.E.

1992-12-01

This document presents an assessment of the severe accident phenomena observed from four Full-Length High-Temperature (FLHT) tests that were performed by the Pacific Northwest Laboratory (PNL) in the National Research Universal (NRU) reactor at Chalk River, Ontario, Canada. These tests were conducted for the US Nuclear Regulatory Commission (NRC) as part of the Severe Accident Research Program. The objectives of the test were to simulate conditions and provide information on the behavior of full-length fuel rods during hypothetical, small-break, loss-of-coolant severe accidents, in commercial light water reactors

Study of containment air cooler capacity in steam air environment during accident conditions

International Nuclear Information System (INIS)

Kansal, M.; Mohan, N.; Bhawal, R.N.; Bajaj, S.S.

2002-01-01

Full text: The air coolers are provided for controlling the temperature in the reactor building during normal operation. These air coolers also serve as the main heat sink for the removal of energy from high enthalpy air-steam mixture expected in reactor building under accident conditions. A subroutine COOLER has been developed to estimate the heat removal rate of the air coolers at high temperature and steam conditions. The subroutine COOLER has been attached with the code PACSR (post accident containment system response) used for containment pressure temperature calculation. The subroutine was validated using design parameters at normal operating condition. A study was done to estimate the heat removal rate for some postulated accident conditions. The study reveals that, under accident conditions, the heat removal rate of air coolers increases several times compared with normal operating conditions

Analysis of Fukushima unit 2 accident considering the operating conditions of RCIC system

Energy Technology Data Exchange (ETDEWEB)

Kim, Sung Il, E-mail: sikim@kaeri.re.kr; Park, Jong Hwa; Ha, Kwang Soon; Cho, Song-Won; Song, JinHo

2016-03-15

Highlights: • Fukushima unit 2 accident was analyzed using MELCOR 1.8.6. • RCIC operating conditions were assumed and best case was selected. • Effect of RCIC operating condition on accident scenario was found. - Abstract: A severe accident in Fukushima occurred on March 11, 2011 and units 1, 2 and 3 were damaged severely. A tsunami following an earthquake made the supply of electricity power stop, and the safety systems, which use AC or DC power in plants could not operate properly. It is supposed that the degree of core degradation of unit 2 is less serious than in the other plants, and it was estimated that the operation of reactor core isolation cooling (RCIC) system at the initial stage of the accident minimized the core damage through decay heat removal. Although the operating conditions of the RCIC system are not known clearly, it can be important to analyze the accident scenario of unit 2. In this study, best case of the Fukushima unit 2 accident was presented considering the operating conditions of the RCIC system. The effects of operating condition on core degradation and fission product release rate to environment were also examined. In addition, importance of torus room flooding level in the accident analysis was discussed. MELCOR 1.8.6 was used in this research, and the geometries of plant and operating conditions of safety system were obtained from TEPCO through OECD/NEA BSAF Project.

Pellet-Cladding Mechanical Interaction Failure Threshold for Reactivity Initiated Accidents for Pressurized Water Reactors and Boiling Water Reactors

Energy Technology Data Exchange (ETDEWEB)

Beyer, Carl E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Geelhood, Kenneth J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-06-01

Pacific Northwest National Laboratory (PNNL) has been requested by the U.S. Nuclear Regulatory Commission to evaluate the reactivity initiated accident (RIA) tests that have recently been performed in the Nuclear Safety Research Reactor (NSRR) and CABRI (French research reactor) on uranium dioxide (UO₂) and mixed uranium and plutonium dioxide (MOX) fuels, and to propose pellet-cladding mechanical interaction (PCMI) failure thresholds for RIA events. This report discusses how PNNL developed PCMI failure thresholds for RIA based on least squares (LSQ) regression fits to the RIA test data from cold-worked stress relief annealed (CWSRA) and recrystallized annealed (RXA) cladding alloys under pressurized water reactor (PWR) hot zero power (HZP) conditions and boiling water reactor (BWR) cold zero power (CZP) conditions.

Key Parameters for Operator Diagnosis of BWR Plant Condition during a Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Clayton, Dwight A [ORNL; Poore III, Willis P [ORNL

2015-01-01

The objective of this research is to examine the key information needed from nuclear power plant instrumentation to guide severe accident management and mitigation for boiling water reactor (BWR) designs (specifically, a BWR/4-Mark I), estimate environmental conditions that the instrumentation will experience during a severe accident, and identify potential gaps in existing instrumentation that may require further research and development. This report notes the key parameters that instrumentation needs to measure to help operators respond to severe accidents. A follow-up report will assess severe accident environmental conditions as estimated by severe accident simulation model analysis for a specific US BWR/4-Mark I plant for those instrumentation systems considered most important for accident management purposes.

NPP Krsko containment environmental conditions during postulated accident

International Nuclear Information System (INIS)

Kozaric, M.; Cavlina, N.; Spalj, S.

1989-01-01

This paper presents NPP Krsko containment pressure and temperature increase during Loss of Coolant Accident (LOCA) and Main Steam Line Break (MSLB). Containment environmental condition calculation was performed by CONTEMPT4/MOD4 computer code. Design accident calculations were performed by RELAP4/MOD6 and RELAP5/MOD1 computer codes. Calculational abilities and application methodology of these codes are presented. The CONTEMPT code is described in more detail. The containment pressure and temperature time distribution are presented as well. (author)

Behavior of small-sized BWR fuel under reactivity initiated accident conditions

International Nuclear Information System (INIS)

Yanagisawa, Kazuaki; Fujishiro, Toshio; Horiki, Oichiro; Chen Dianshan; Takeuchi, Kiyoshi.

1992-01-01

The present work was performed on this small-sized BWR fuel, where Zr liner and rod prepressurization were taken as experimental parameters. Experiment was done under simulated reactivity initiated accident (RIA) conditions at Nuclear Safety Research Reactor (NSRR) belonged to Japan Atomic Energy Research Institute (JAERI). Major remarks obtained are as follows: (1) Three different types of the fuel rods consisted of (a) Zr lined/pressurized (0.65MPa), (b) Zr lined/non-pressurized and (c) non-Zr lined/pressurized (o.65MPa) were used, respectively. Failure thresholds of these were not less than that (260 cal/g·fuel) described in Japanese RIA Licensing Guideline. Small-sized BWR and conventional 8 x 8 BWR fuels were considered to be in almost the same level in failure threshold. Failure modes of the three were (a) cladding melt/brittle, (b) cladding melt/brittle and (c) rupture by large ballooning, respectively. (2) The magnitude of pressure pulse at fuel fragmentation was also studied by lined/pressurized and non-lined/pressurized fuels. Above the energy deposition of 370 cal/g·fuel, mechanical energy (or pressure) was found to be released from these fragmented fuels. No measurable difference was, however, observed between the tested fuels and NSRR standard (and conventional 8 x 8 BWR) fuels. (3) It is worthy of mentioning that Zr liner tended to prevent the cladding from large ballooning. Non-lined/pressurized fuel tended to cause wrinkle deformation at cladding. Hence, cladding external was notched much by the wrinkles. (4) Time to fuel failure measured from the tested BWR fuels (pressurization < 0.6MPA) was longer than that measured from PWR fuels (pressurization < 3.2MPa). The magnitude of the former was of the order of 3 ∼ 6s, while that of the latter was < 1s. (J.P.N.)

Verification of computer code FPRETAIN with respect to RIA data from SPERT and PBF experiments

International Nuclear Information System (INIS)

Heo, Young-Ho; Yanagisawa, Kazuaki.

1992-12-01

This report presents the comparisons between calculated and measured fuel rod behavior and the analysis of stress for preirradiated LWR type fuel rods during reactivity initiated accident (RIA) conditions. For the calculations, FPRETAIN computer code which can simulate the fuel behavior under RIA conditions at extended burnup stage was used. For the experimental, data obtained from the Special Power Excursion Reactor Test (SPERT) and the Power Burst Facility (PBF) tests were used. The results of the comparisons showed that the FPRETAIN code predicted well the tendency of the fuel rod behavior during RIA. From the results of the stress analysis, it was found that the maximum hoop stress of cladding was not proportional to the energy deposition of fuel rod. Calculated cladding maximum hoop stress of failed fuel at high burnup was not lower than that of intact fresh or low burnup fuel. (author)

Assessment of Equipment Capability to Perform Reliably under Severe Accident Conditions

International Nuclear Information System (INIS)

2017-07-01

The experience from the last 40 years has shown that severe accidents can subject electrical and instrumentation and control (I&C) equipment to environmental conditions exceeding the equipment’s original design basis assumptions. Severe accident conditions can then cause rapid degradation or damage to various degrees up to complete failure of such equipment. This publication provides the technical basis to consider when assessing the capability of electrical and I&C equipment to perform reliably during a severe accident. It provides examples of calculation tools to determine the environmental parameters as well as examples and methods that Member States can apply to assess equipment reliability.

High burnup (41 - 61 GWd/tU) BWR fuel behavior under reactivity initiated accident conditions

Energy Technology Data Exchange (ETDEWEB)

Nakamura, Takehiko; Kusagaya, Kazuyuki; Yoshinaga, Makio; Uetsuka, Hiroshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2001-12-01

High burnup boiling water reactor (BWR) fuel was pulse irradiated in the Nuclear Safety Research Reactor (NSRR) to investigate fuel behavior under cold startup reactivity initiated accident (RIA) conditions. Temperature, deformation, failure, and fission gas release behavior under the simulated RIA condition was studied in the tests. Fuel failure due to pellet-cladding mechanical interaction (PCMI) did not occur in the tests with typical domestic BWR fuel at burnups up to 56 GWd/tU, because they had limited cladding embrittlement due to hydrogen absorption of about 100 ppm or less. However, the cladding failure occurred in tests with fuel at a burnup of 61 GWd/tU, in which the peak hydrogen content in the cladding was above 150 ppm. This type of failure was observed for the first time in BWR fuels. The cladding failure occurred at fuel enthalpies of 260 to 360 J/g (62 to 86 cal/g), which were higher than the PCMI failure thresholds decided by the Japanese Nuclear Safety Commission. From post-test examinations of the failed fuel, it was found that the crack in the BWR cladding progressed in a manner different from the one in PWR cladding failed in earlier tests, owing to its more randomly oriented hydride distribution. Because of these differences, the BWR fuel was judged to have failed at hydrogen contents lower than those of the PWR fuel. Comparison of the test results with code calculations revealed that the PCMI failure was caused by thermal expansion of pellets, rather than by the fission gas expansion in the pellets. The gas expansion, however, was found to cause large cladding hoop deformation later after the cladding temperature escalated. (author)

Reactivity Initiated Accident Test Series: Test RIA 1-2. Quick look report

International Nuclear Information System (INIS)

Martinson, Z.R.; Semken, R.S.; Smith, R.H.; Osetek, D.J.

1978-12-01

The primary objectives of Test RIA 1-2 were to (a) characterize the response of preirradiated fuel rods during an RIA event conducted at boiling water reactor (BWR) hot-startup conditions for an axial peak pellet surface energy of 200 cal/g UO 2 , and (b) evaluate the effect of internal rod pressure on preirradiated fuel rod response during an RIA event. The test consisted of four, individually shrouded, pressurized water reactor-type fuel rods previously irradiated to burnups of about 4800 MWd/t. In addition to the power calibration and preconditioning, the fuel rods were subjected to a single power burst that deposited a total pellet surface energy of approximately 200 cal/gm UO 2 at the axial peak power location (estimated using the core power chambers to relate steady state and transient powers). The test data indicate that the two irradiated fuel rods prepressurized to 2.41 MPa did not fail. FRAP-T4 calculations had predicted that prompt cladding rupture would occur for pellet surface energy depositions of 206 cal/g or greater. Although the two fuel rods prepressurized to 2.41 MPa did not fail, the data indicate that at least one of the two fuel rods prepressurized to 0.1 MPa did fail. Based on the core power chamber data, this rod failure indicates a threshold for the preirradiated fuel rods near or below 200 cal/g UO 2 total pellet surface energy at the axial flux peak

Reliability analysis of emergency decay heat removal system of nuclear ship under various accident conditions

International Nuclear Information System (INIS)

Matsuoka, Takeshi

1984-01-01

A reliability analysis is given for the emergency decay heat removal system of the Nuclear Ship ''Mutsu'' and the emergency sea water cooling system of the Nuclear Ship ''Savannah'', under ten typical nuclear ship accident conditions. Basic event probabilities under these accident conditions are estimated from literature survey. These systems of Mutsu and Savannah have almost the same reliability under the normal condition. The dispersive arrangement of a system is useful to prevent the reduction of the system reliability under the condition of an accident restricted in one room. As for the reliability of these two systems under various accident conditions, it is seen that the configuration and the environmental condition of a system are two main factors which determine the reliability of the system. Furthermore, it was found that, for the evaluation of the effectiveness of safety system of a nuclear ship, it is necessary to evaluate its reliability under various accident conditions. (author)

Inherent safety features of the HTTR revealed in the accident condition

International Nuclear Information System (INIS)

Kunitomi, K.; Shinozaki, M.; Baba, O.; Saito, S.

1992-01-01

The High Temperature Engineering Test Reactor (HTTR) being constructed by JAERI (Japan Atomic Energy Research Institute) is a graphite-moderated and helium-cooled reactor with an outlet gas temperature of 950degC. The inherent safety characteristics in the HTTR prevent temperature increase of reactor fuels and fission product release from the reactor core in postulated accident conditions. The reactor core can be cooled by a Vessel Cooling System (VCS) indirectly, even in the case that no forced cooling is expected during the accident such as primary pipe break. The VCS consists of independent water cooling loop and cooling panel around the reactor pressure vessel. The cooling panel whose temperature of 60-90degC cools the reactor pressure vessel by radiation and removes the decay heat from the core indirectly. Furthermore, even if failure of VCS is assumed during this accident as a severe accident, the reactor core is remained safe despite the temperature increase of biological concrete shield around the reactor pressure vessel. This paper describes the inherent safety features of the HTTR specially focused on the accident condition without forced cooling. The detailed analytical results of such an accident are described together with clarifying the role of the VCS. (author)

Effect of RCIC Operating Conditions on the Accident Scenario in Fukushima Unit 2

International Nuclear Information System (INIS)

Kim, Sung Il; Park, Jong Hwa; Ha, Kwang Soon

2015-01-01

This study was conducted by using MELCOR 1.8.6. Fukushima unit 2 accident was analyzed using MELCOR in this study, and best estimate scenario with considering RCIC operating conditions was presented. Researches on the boiling water reactor (BWR) plant with reactor core isolation cooling (RCIC) system have been conducted. Research on the RCIC operation in Fukushima unit 2 was also conducted by Sandia National Laboratory. MELCOR analysis of the Fukushima unit 2 accident was conducted in the report and energy balance in wetwell was described by considering RCIC operation. However, the effect of RCIC operation condition on the accident scenario has not been studied. The operating conditions of RCIC system affect the pressures in wetwell and drywell, and the high pressure can make leakage path of fission product from PCV to reactor building. Thus it can be directly related with the amount of fission product which released to environment. In this study, severe accident on Fukushima unit 2 was analyzed considering the operating condition of RCIC system, and best estimated scenario was presented. In addition, the effect of RCIC turbine efficiency on the accident progression was examined. Energy balance in suppression chamber was also considered with discussion on the effect of torus room flooding level. It was found that the operating condition of RCIC turbine not only affects the variation of drywell pressure but also the amount of released fission products to environment. It was also confirmed that the RCIC turbine efficiency in the accident would be less than normal operating condition

Applicability of modified burst test data to reactivity initiated accident

Energy Technology Data Exchange (ETDEWEB)

Yueh, K., E-mail: yuehky@hotmail.com

2017-05-15

A comprehensive irradiated cladding mechanical property dataset was generated by a recently developed modified burst test (MBT) under reactivity initiated accident (RIA) loading conditions [1,2]. The test data contains a wide range of test conditions that could bridge the gap between fast transient test reactor data (short pulse and/or low temperature) and prototypical commercial reactor conditions. This paper documents an evaluation performed to demonstrate the applicability of the MBT data to fuel cladding performance under RIA conditions. The current effort includes a comparison of calculated fuel cladding failure/burst strain for tests conducted at the Japan Atomic Energy Agency's (JAEA) Nuclear Safety Research Reactor (NSRR) to the MBT dataset, and an evaluation of potential mechanisms on how some NSRR tests survived beyond the cladding loading capacity. A simple shell model, coupled with temperature output from the Falcon fuel performance code, was used to calculate the fuel pellet thermal expansion of NSRR tests at the point of failure. The calculated fuel pellet thermal expansion correlates well directly with the MBT data at similar loading conditions. A 3-dimensional (3D) finite element analysis (FEA) model was used to evaluate fuel movement potential during a RIA. The evaluation indicates fuel relocation into the pellet chamfer and later into the dish is possible once a temperature threshold is reached before cladding failure and thus could significantly increase the fuel rod energy absorption capacity in a RIA event.

Computer code calculations of the TMI-2 accident: initial and boundary conditions

International Nuclear Information System (INIS)

Behling, S.R.

1985-05-01

Initial and boundary conditions during the Three Mile Island Unit 2 (TMI-2) accident are described and detailed. A brief description of the TMI-2 plant configuration is given. Important contributions to the progression of the accident in the reactor coolant system are discussed. Sufficient information is provided to allow calculation of the TMI-2 accident with computer codes

LOFA and RIA analysis of the Indonesian Multipurpose research reactor RSG-GAS 1)

International Nuclear Information System (INIS)

Endiah Puji Hastuti; Hudi Hastowo; Iman Kuntoro

1999-01-01

Investigation on accident of the Indonesian Multipurpose research reactor RSG-GAS has been performed by computer simulation technique. Two groups of transients were considered, namely transient due to loss of primary cooling system (LOFA) and power excursion due to reactivity insertion (RIA). In such a transient condition, the Common Mode Failure (CMF) is considered and it will induce a situation so called unprotected transient or Anticipated Transient Without Scram (ATWS). RELAP5, PARET-ANL and EUREKA-2RR computer packages have been applied for these analyses. Simulations result done using these computer packages showed that in the occurrence of LOFA and RIA, failure on fuel elements is limited to the region with the highest power factor. (author)

Hydrogen formation and control under postulated LMFBR accident conditions

International Nuclear Information System (INIS)

Armstrong, G.R.; Wierman, R.W.

1976-09-01

The objective of this study is to experimentally investigate the potential for autoignition and combustion of hydrogen-sodium mixtures which may be produced in LMFBR accidents. The purpose and ultimate usefulness of this work is to provide data that will establish the validity and acceptability of mechanisms inherent to the LMFBR that could either prevent or delay the accumulation of hydrogen gas to less than 4 percent (V) in the Reactor Containment Building (RCB) under accident conditions. The results to date indicate that sodium and sodium-hydrogen mixtures such as may be expected during LMFBR postulated accidents will ignite upon entering an air atmosphere and that the hydrogen present will be essentially all consumed until such time that the oxygen concentration is depleted

RIA simulation tests using driver tube for ATF cladding

Energy Technology Data Exchange (ETDEWEB)

Cinbiz, Mahmut N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Brown, N. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lowden, R. R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Linton, K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, K. A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-07-01

Pellet-cladding mechanical interaction (PCMI) is a potential failure mechanism for accident-tolerant fuel (ATF) cladding candidates during a reactivity-initiated accident (RIA). This report summarizes Fiscal Year (FY) 2017 research activities that were undertaken to evaluate the PCMI-like hoop-strain-driven mechanical response of ATF cladding candidates. To achieve various RIA-like conditions, a modified-burst test (MBT) device was developed to produce different mechanical pulses. The calibration of the MBT instrument was accomplished by performing mechanical tests on unirradiated Generation-I iron-chromium-aluminum (FeCrAl) alloy samples. Shakedown tests were also conducted in both FY 2016 and FY 2017 using unirradiated hydrided ZIRLO™ tube samples. This milestone report focuses on testing of ATF materials, but the benchmark tests with hydrided ZIRLO™ tube samples are documented in a recent journal article.a For the calibration and benchmark tests, the hoop strain was monitored using strain gauges attached to the sample surface in the hoop direction. A novel digital image correlation (DIC) system composed of a single high-speed camera and an array of six mirrors was developed for the MBT instrument to better resolve the failure behavior of samples and to provide useful data for validation of high-fidelity modeling and simulation tools. The DIC system enable a 360° view of a sample’s outer surface. This feature was added to the instrument to determine the precise failure location on a sample’s surface for strain predictions. The DIC system was tested on several silicon carbide fiber/silicon carbide matrix (SiC/SiC) composite tube samples at various pressurization rates of the driver tube (which correspond to the strain rates for the samples). The hoop strains for various loading conditions were determined for the SiC/SiC composite tube samples. Future work is planned to enhance understanding of the failure behavior of the ATF cladding candidates of age

Noble gas control room accident filtration system for severe accident conditions (N-CRAFT)

International Nuclear Information System (INIS)

Hill, Axel; Stiepani, Cristoph; Drechsler, Michael

2015-01-01

Severe accidents might cause the release of airborne radioactive substances to the environment of the NPP either due to containment leakages or due to intentional filtered containment venting. In the latter case aerosols and iodine are retained, however noble gases are not retainable by the FCVS or by conventional air filtration systems like HEPA filters and iodine absorbers. Radioactive noble gases nevertheless dominate the activity release depending on the venting procedure and the weather conditions. To prevent unacceptable contamination of the control room atmosphere by noble gases, AREVA GmbH has developed a noble gas control room accident filtration system (CRAFT) which can supply purified fresh air to the control room without time limitation. The retention process is based on dynamic adsorption of noble gases on activated carbon. The system consists of delay lines (carbon columns) which are operated by a continuous and simultaneous adsorption and desorption process. CRAFT allows minimization of the dose rate inside the control room and ensures low radiation exposure to the staff by maintaining the control room environment suitable for prolonged occupancy throughout the duration of the accident. CRAFT consists of a proven modular design either transportable or permanently installed. (author)

INPR ACPR utilization in fuel behaviour studies under accidental condition

International Nuclear Information System (INIS)

Negut, Gheorghe; Popov, Mircea

1990-01-01

This paper is dedicated to the experimental program, investigating CANDU type fuel behaviour in transient condition, as well as the facilities supporting this program. The tests Reactivity Initiated Accident type. The experiments were performed within TRIGA ACPR facility, installed at INSTITUTE for NUCLEAR POWER REACTORS, Pitesti, ROMANIA. Studies of the safety issues took a great international developement during last years. In USA, Japan, owners of the similar reactors, and USSR there are a big commitment to such programs, intended to establish the nuclear fuel behaviour under RIA-conditions. In our country, too, there are programs aiming a complete testing of the CANDU type fuels. As it is known, RIA is not a CANDU specific accident, but the fuel behaviour in such conditions can give useful informations on the fuel cladding failure threshold and about reflooding post LOCA heat transfer condition. Based on some papers and specific requirements it was initiated and developed a safety research program on CANDU type fuel using the ACPR. The paper describes the reactor,test capsule, instrumentation, fuel samples, tests, post irradiation results. (orig.)

Influence of initial conditions on rod behaviour during boiling crisis phase following a reactivity initiated accident

International Nuclear Information System (INIS)

Georgenthum, V.; Sugiyama, T.

2010-01-01

In the frame of their research programs on high burn-up fuel safety, the French Institute for Radioprotection and Nuclear Safety (IRSN) and the Japan Atomic Energy Agency (JAEA) performed a large set of tests devoted to the study of PWR fuel rod behavior during Reactivity Initiated Accident (RIA) respectively in the CABRI reactor and in the NSRR reactor. The reactor test conditions are different in terms of coolant nature, temperature and pressure. In the CABRI reactor, tests were performed until now with sodium coolant at 280 Celsius degrees and 3 bar. In the NSRR reactor most of the tests were performed with stagnant water at 20 C. degrees and atmospheric pressure but recently a new high temperature high pressure capsule has been developed which allows to performed tests at up to 280 Celsius degrees and 70 bar. The paper discusses the influence of test conditions on rod behaviour during boiling phase, based on tests results and SCANAIR code calculations. The study shows that when the boiling crisis is reached, the initial inner and outer rod pressure have an essential impact on the clad straining and possible ballooning. The analysis of the different test conditions makes it possible to discriminate the influence of initial conditions on the different phases of the transient and is useful for modelling and code development. (authors)

Computational analysis of the behaviour of nuclear fuel under steady state, transient and accident conditions

International Nuclear Information System (INIS)

2007-12-01

Accident analysis is an important tool for ensuring the adequacy and efficiency of the provision in the defence in depth concept to cope with challenges to plant safety. Accident analysis is the milestone of the demonstration that the plant is capable of meeting any prescribed limits for radioactive releases and any other acceptable limits for the safe operation of the plant. It is used, by designers, utilities and regulators, in a number of applications such as: (a) licensing of new plants, (b) modification of existing plants, (c) analysis of operational events, (d) development, improvement or justification of the plant operational limits and conditions, and (e) safety cases. According to the defence in depth concept, the fuel rod cladding constitutes the first containment barrier of the fission products. Therefore, related safety objectives and associated criteria are defined, in order to ensure, at least for normal operation and anticipated transients, the integrity of the cladding, and for accident conditions, acceptable radiological consequences with regard to the postulated frequency of the accident, as usually identified in the safety analysis reports. Therefore, computational analysis of fuel behaviour under steady state, transient and accident conditions constitutes a major link of the safety case in order to justify the design and the safety of the fuel assemblies, as far as all relevant phenomena are correctly addressed and modelled. This publication complements the IAEA Safety Report on Accident Analysis for Nuclear Power Plants (Safety Report Series No. 23) that provides practical guidance for establishing a set of conceptual and formal methods and practices for performing accident analysis. Computational analysis of the behaviour of nuclear fuel under transient and accident conditions, including normal operation (e.g. power ramp rates) is developed in this publication. For design basis accidents, depending on the type of influence on a fuel element

On the removal of airborne particulate radioactivity under accident conditions

International Nuclear Information System (INIS)

Ruedinger, V.; Wilhelm, J.G.

1985-03-01

In the case of an accident, the filter elements in the ventilation systems of a nuclear facility may become a part of the remaining fission product barrier. Within the framework of the Project Nuclear Safety of the Karlsruhe Nuclear Research Center, contributions are made to an increase in reliability of the air cleaning systems under accident conditions. These include the development and verification of computer programs for the estimation of those conditions prevailing inside the air cleaning systems in the case of an accident. Experimental investigations into the response of HEPA filters to differential pressures involving both dry and moist air have demonstrated the occurence of structural failures with subsequent loss of efficiency at relatively low values of differential pressures. With regard to further investigations, a new test facility was put into operation for the realization of superimposed challenges. A new method for testing particulate removal efficiency under high temperature or high humidity was developed. Finally, first results of code development work and of the corresponding verification experiments are reported on. (orig.) [de

Driving force of PCMI failure under reactivity initiated accident conditions and influence of hydrogen embrittlement on failure limit

International Nuclear Information System (INIS)

Tomiyasu, Kunihiko; Sugiyama, Tomoyuki; Nakamura, Takehiko; Fuketa, Toyoshi

2005-09-01

In order to clarify the driving force of PCMI (Pellet/Cladding Mechanical Interaction) failure on high burnup fuels and to investigate the influence of hydrogen embrittlement on failure limit under RIA (Reactivity Initiated Accident) conditions, RIA-simulation experiments were performed on fresh fuel rods in the NSRR (Nuclear Safety Research Reactor). The driving force of PCMI was restricted only to thermal expansion of pellet by using fresh UO 2 pellets. Fresh claddings were pre-hydrided to simulate hydrogen absorption of high burnup fuel rods. In seven experiments out of fourteen, test rods resulted in PCMI failure, which has been observed in the NSRR tests on high burnup PWR fuels, in terms of the transient behavior and the fracture configuration. This indicates that the driving force of PCMI failure is sufficiently explained with thermal expansion of pellet and a contribution of fission gas on it is small. A large number of incipient cracks were generated in the outer surface of the cladding even on non-failed fuel rods, and they stopped at the boundary between hydride rim, which was a hydride layer localized in the periphery of the cladding, and metallic layer. It suggests that the integrity of the metallic layer except for the hydride rim has particular importance for failure limit. Fuel enthalpy at failure correlates with the thickness of hydride rim, and tends to decrease with thicker hydride layer. (author)

Behaviour of LWR core materials under accident conditions. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1996-12-01

At the invitation of the Government of the Russian Federation, following a proposal of the International Working Group on Water Reactor Fuel Performance and Technology, the IAEA convened a Technical Committee Meeting on Behaviour of LWR Core Materials Under Accident Conditions from 9 to 13 October 1995 in Dimitrovgrad to analyze and evaluate the behaviour of LWR core materials under accident conditions with special emphasis on severe accidents. In-vessel severe accidents phenomena were considered in detail, but specialized thermal hydraulic aspects as well as ex-vessel phenomena were outside the scope of the meeting. Forty participants representing eight countries attended the meeting. Twenty-three papers were presented and discussed during five sessions. Refs, figs, tabs

Using modular neural networks to monitor accident conditions in nuclear power plants

International Nuclear Information System (INIS)

Guo, Z.

1992-01-01

Nuclear power plants are very complex systems. The diagnoses of transients or accident conditions is very difficult because a large amount of information, which is often noisy, or intermittent, or even incomplete, need to be processed in real time. To demonstrate their potential application to nuclear power plants, neural networks axe used to monitor the accident scenarios simulated by the training simulator of TVA's Watts Bar Nuclear Power Plant. A self-organization network is used to compress original data to reduce the total number of training patterns. Different accident scenarios are closely related to different key parameters which distinguish one accident scenario from another. Therefore, the accident scenarios can be monitored by a set of small size neural networks, called modular networks, each one of which monitors only one assigned accident scenario, to obtain fast training and recall. Sensitivity analysis is applied to select proper input variables for modular networks

Chemical phenomena under severe accident conditions

International Nuclear Information System (INIS)

Powers, D.A.

1988-01-01

A severe nuclear reactor accident is expected to involve a vast number of chemical processes. The chemical processes of major safety significance begin with the production of hydrogen during steam oxidation of fuel cladding. Physico-chemical changes in the fuel and the vaporization of radionuclides during reactor accidents have captured much of the attention of the safety community in recent years. Protracted chemical interactions of core debris with structural concrete mark the conclusion of dynamic events in a severe accident. An overview of the current understanding of chemical processes in severe reactor accident is provided in this paper. It is shown that most of this understanding has come from application of findings from other fields though a few areas have in the past been subject to in-depth study of a fundamental nature. Challenges in the study of severe accident chemistry are delineated

Behavior of LWR fuel elements under accident conditions

International Nuclear Information System (INIS)

Albrecht, H.; Bocek, M.; Erbacher, F.; Fiege, A.; Fischer, M.; Hagen, S.; Hofmann, P.; Holleck, H.; Karb, E.; Leistikow, S.; Melang, S.; Ondracek, G.; Thuemmler, F.; Wiehr, K.

1977-01-01

In the frame of the German reactor safety research program, the Kernforschungszentrum Karlsruhe is carrying out a comprehensive program on the behavior of LWR fuel elements under a variety of power cooling mismatch conditions in particular during loss-of-coolant accidents. The major objectives are to establish a detailed quantitative understanding of fuel rod failures mechanisms and their thresholds, to evaluate the safety margins of power reactor cores under accident conditions and to investigate the feedback of fuel rod failures on the efficiency of emergency core cooling systems. This detailed quantitative understanding is achieved through extensive basic and integral experiments and is incorporated in a fuel behavior code. On the basis of these results the design of power reactor fuel elements and of safety devices can be further improved. The results of investigations on the inelastic deformation (ballooning) behavior of Zircaloy 4 cladding at LOCA temperatures in oxidizing atmosphere are presented. Depending upon strain rate and temperature superplastic deformation behavior was observed. In the equation of state of Zry 4 the strain rate sensitivity index depends strongly upon strain and in the superplastic region upon sample anisotropy. Oxidation kinetics experiments with Zry-tubes at 900-1300 0 C showed that the Baker-Just correlation describes the reality quite conservative. Therefore a reduction of the amount of Zry oxidation can be assumed in the course of a LOCA. The external oxidation of Zry-cladding by steam as well as internal oxidation by the oxygen in oxide fuel and fission products (Cs, I, Te) have an influence on the strain and rupture behavior of Zry-cladding at LOCA temperatures. In out-of-pile and inpile experiments the mechanical and thermal behavior of fuel rods during the blowdown, the heatup and the reflood phases of a LOCA are investigated under representative and controlled thermohydraulic conditions. The task of the inpile experiments is

Numerical Study of Severe Accidents on Containment Venting Conditions

Energy Technology Data Exchange (ETDEWEB)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong [FNC Technology Co., Yongin (Korea, Republic of); Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek [KHNP-CRI, Daejeon (Korea, Republic of)

2014-10-15

Under severe accident, the containment integrity can be challenged due to over-pressurization by steam and non-condensable gas generation. According to Seismic Probabilistic Safety Assessment (PSA) result, the late containment failure by over-pressurization has been identified as the most probable containment failure mode. In addition, the analyses of Fukushima nuclear power plant accident reveal the necessity of the proper containment depressurization to prevent the large release of the radionuclide to environment. Containment venting has been considered as an effective approach to maintain the containment integrity from over-pressurization. Basic idea of containment venting is to relieve the pressure inside of the containment by establishing a flow path to the external environment. To ensure the containment integrity under over-pressure conditions, it is crucial to conduct the containment vent in a timely manner with a sufficient discharge flow rate. It is also important to optimize the vent line size to prevent additional risk of leakage and to install at the site with limited space availability. The purpose of this study is to identify the effective venting conditions for preventing the containment over-pressurization and investigate the vent flow characteristics to minimize the consequence of the containment ventilation.. In order that, thermodynamic behavior of the containment and the discharged flow depending on different vent strategies are analyzed and compared. The representative accident scenarios are identified by reviewing the Level 2 PSA result and the sensitivity analyses with varying conditions (i.e. vent line size and vent initiation pressure) are conducted. MAAP5 model for the OPR1000 Korea nuclear power plant has been used for severe accident simulations. Containment venting can be an effective strategy to prevent the significant failure of the containment due to over-pressurization. However, it should be carefully conducted because the vented

Numerical Study of Severe Accidents on Containment Venting Conditions

International Nuclear Information System (INIS)

Lee, Na Rae; Bang, Young Suk; Park, Tong Kyu; Lee, Doo Yong; Choi, Yu Jung; Lee, Sang Won; Kim, Hyeong Taek

2014-01-01

Under severe accident, the containment integrity can be challenged due to over-pressurization by steam and non-condensable gas generation. According to Seismic Probabilistic Safety Assessment (PSA) result, the late containment failure by over-pressurization has been identified as the most probable containment failure mode. In addition, the analyses of Fukushima nuclear power plant accident reveal the necessity of the proper containment depressurization to prevent the large release of the radionuclide to environment. Containment venting has been considered as an effective approach to maintain the containment integrity from over-pressurization. Basic idea of containment venting is to relieve the pressure inside of the containment by establishing a flow path to the external environment. To ensure the containment integrity under over-pressure conditions, it is crucial to conduct the containment vent in a timely manner with a sufficient discharge flow rate. It is also important to optimize the vent line size to prevent additional risk of leakage and to install at the site with limited space availability. The purpose of this study is to identify the effective venting conditions for preventing the containment over-pressurization and investigate the vent flow characteristics to minimize the consequence of the containment ventilation.. In order that, thermodynamic behavior of the containment and the discharged flow depending on different vent strategies are analyzed and compared. The representative accident scenarios are identified by reviewing the Level 2 PSA result and the sensitivity analyses with varying conditions (i.e. vent line size and vent initiation pressure) are conducted. MAAP5 model for the OPR1000 Korea nuclear power plant has been used for severe accident simulations. Containment venting can be an effective strategy to prevent the significant failure of the containment due to over-pressurization. However, it should be carefully conducted because the vented

The role of grain boundary fission gases in high burn-up fuel under reactivity initiated accident conditions

International Nuclear Information System (INIS)

Lemoine, F.; Papin, J.; Frizonnet, J.M.; Cazalis, B.; Rigat, H.

2002-01-01

In the frame of reactivity-initiated accidents (RIA) studies, the CABRI REP-Na programme is currently performed, focused on high burn-up UO 2 and MOX fuel behaviour. From 1993 to 1998, seven tests were performed with UO 2 fuel and three with MOX fuel. In all these tests, particular attention has been devoted to the role of fission gases in transient fuel behaviour and in clad loading mechanisms. From the analysis of experimental results, some basic phenomena were identified and a better understanding of the transient fission gas behaviour was obtained in relation to the fuel and clad thermo-mechanical evolution in RIA, but also to the initial state of the fuel before the transient. A high burn-up effect linked to the increasing part of grain boundary gases is clearly evidenced in the final gas release, which would also significantly contribute to the clad loading mechanisms. (authors)

Thermalydraulic processes in the reactor coolant system of a BWR under severe accident conditions

International Nuclear Information System (INIS)

Hodge, S.A.

1990-01-01

Boiling water reactors (BWRs) incorporate many unique structural features that make their expected response under severe accident conditions very different from that predicted in the case of pressurized water reactor accident sequences. Automatic main steam isolation valve (MIV) closure as the vessel water level approaches the top of the core would cause reactor vessel isolation while automatic recirculation pump trip would limit the in-vessel flows to those characteristic of natural circulation (as disturbed by vessel relief valve actuation). This paper provides a discussion of the BWR control blade, channel box, core plate, control rod guide tube, and reactor vessel safety relief valve (SRV) configuration and the effects of these structural components upon thermal hydraulic processes within the reactor vessel under severe accident conditions. The dominant BWR severe accident sequences as determined by probabilistic risk assessment are described and the expected timing of events for the unmitigated short-term station blackout severe accident sequence at the Peach Bottom atomic power station is presented

Electrical equipment performance under severe accident conditions (BWR/Mark 1 plant analysis): Summary report

International Nuclear Information System (INIS)

Bennett, P.R.; Kolaczkowski, A.M.; Medford, G.T.

1986-09-01

The purpose of the Performance Evaluation of Electrical Equipment during Severe Accident States Program is to determine the performance of electrical equipment, important to safety, under severe accident conditions. In FY85, a method was devised to identify important electrical equipment and the severe accident environments in which the equipment was likely to fail. This method was used to evaluate the equipment and severe accident environments for Browns Ferry Unit 1, a BWR/Mark I. Following this work, a test plan was written in FY86 to experimentally determine the performance of one selected component to two severe accident environments

Predictions of structural integrity of steam generator tubes under normal operating, accident, and severe accident conditions

International Nuclear Information System (INIS)

Majumdar, S.

1996-09-01

Available models for predicting failure of flawed and unflawed steam generator tubes under normal operating, accident, and severe accident conditions are reviewed. Tests conducted in the past, though limited, tended to show that the earlier flow-stress model for part-through-wall axial cracks overestimated the damaging influence of deep cracks. This observation is confirmed by further tests at high temperatures as well as by finite element analysis. A modified correlation for deep cracks can correct this shortcoming of the model. Recent tests have shown that lateral restraint can significantly increase the failure pressure of tubes with unsymmetrical circumferential cracks. This observation is confirmed by finite element analysis. The rate-independent flow stress models that are successful at low temperatures cannot predict the rate sensitive failure behavior of steam generator tubes at high temperatures. Therefore, a creep rupture model for predicting failure is developed and validated by tests under varying temperature and pressure loading expected during severe accidents

Effects of pellet shape on the fuel failure behavior under a RIA condition

International Nuclear Information System (INIS)

Hosokawa, Takanori; Hoshi, Tsutao; Yanagihara, Satoshi; Iwamura, Takamichi; Orita, Yoshihiko.

1980-10-01

The two types of fuel rods with different pellet shaped, i.e. flat pellets and dished pellets, were tested in the NSRR to investigate the effects of pellet shapes on the fuel failure behavior under an RIA condition and the results were compared with those of the chamfered pellet fuel rods which are used as the reference rod in the NSRR experiments. In addition, the deformation of pellets due to thermal expansion is calculated by using an FEM computer code. Through the above results, following conclusions are obtained. (1) In the experiments, insignificant differences on the cladding surface temperature responses and the appearance of post-irradiated rods are observed in each type of rods. (2) Evident differences on the deformation of fuel pellets have not appeared in the calculation. (3) In the RIA conditions, it is concluded that the fuel failure behavior and threshold energy might not be affected by pellet shape of which size is in the range of the current LWR's fuel rods. (author)

Accident information needs

International Nuclear Information System (INIS)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-01-01

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information

Accident information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-12-31

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

Accident information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Arcieri, W.C.; Ward, L.W.

1992-01-01

A Five-step methodology has been developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and the severe accident conditions to evaluate the availability of the instrumentation to supply needed plant information.

Analysis of some accident conditions in confirmation of the HTGR safety

Energy Technology Data Exchange (ETDEWEB)

Grebennik, V. N.; Grishanin, E. I.; Kukharkin, N. E.; Mikhailov, P. V.; Pinchuk, V. V.; Ponomarev-Stepnoy, N. N.; Fedin, G. I.; Shilov, V. N.; Yanushevich, I. V. [Gosudarstvennyj Komitet po Ispol' zovaniyu Atomnoj Ehnergii SSSR, Moscow. Inst. Atomnoj Ehnergii

1981-01-15

This report concerns some accident conditions for the HTGR-50 demonstrational reactor which along with the safety features common to the typical HTGR differs in design. The analyses carried out on the accident situations showed that due to the high heat capacity of the graphite core and negative temperature effect of the reactivity the HTGR-50 reactor is effectively selfcontrolled at different perturbations of the reactivity and has low sensitivity to the failure of the core cooling. The primary circuit depressurization accident should be thoroughly studied because of the dangerous consequences i.e. the core overheating and the reactivity release into the environment. As a whole, the studies now in progress show that the problem of the HTGR safety can be successfully solved.

Analysis of some accident conditions in confirmation of the HTGR safety

International Nuclear Information System (INIS)

Grebennik, V.N.; Grishanin, E.I.; Kukharkin, N.E.; Mikhailov, P.V.; Pinchuk, V.V.; Ponomarev-Stepnoy, N.N.; Fedin, G.I.; Shilov, V.N.; Yanushevich, I.V.

1981-01-01

This report concerns some accident conditions for the HTGR-50 demonstrational reactor which along with the safety features common to the typical HTGR differs in design. The analyses carried out on the accident situations showed that due to the high heat capacity of the graphite core and negative temperature effect of the reactivity the HTGR-50 reactor is effectively selfcontrolled at different perturbations of the reactivity and has low sensitivity to the failure of the core cooling. The primary circuit depressurization accident should be thoroughly studied because of the dangerous consequences i.e. the core overheating and the reactivity release into the environment. As a whole, the studies now in progress show that the problem of the HTGR safety can be successfully solved

Recent results on the RIA test in IGR reactor

International Nuclear Information System (INIS)

Asmolov, V.; Yegorova, L.

1997-01-01

At the 23d WRSM meeting the data base characterizing results of VVER high burnup fuel rods tests under reactivity-initiated accident (RIA) conditions was presented. Comparison of PWR and VVER failure thresholds was given also. Additional analysis of the obtained results was being carried out during 1996. The results of analysis show that the two different failure mechanisms were observed for PWR and VVER fuel rods. Some factors which can be as the possible reasons of these differences are presented. First of them is the state of preirradiated cladding. Published test data for PWR high burnup fuel rods demonstrated that the PWR high burnup fuel rods failed at the RIA test are characterized by very high level of oxidation and hydriding for the claddings. Corresponding researches were performed at Institute of Atomic Reactors (RLAR, Dimitrovgrad, Russia) for large set of VVER high burnup fuel rods. Results of these investigations show that preirradiated commercial Zr-1%Nb claddings practically keep their initial levels of oxidation and H 2 concentration. Consequently the VVER preirradiated cladding must keep the high level of mechanical properties. The second reason leading to differences between failure mechanisms for two types of high burnup fuel rods can be the test conditions. Now such kind of analysis have been performed by two methods

Off-gas and air cleaning systems for accident conditions in nuclear power plants

International Nuclear Information System (INIS)

1993-01-01

This report surveys the design principles and strategies for mitigating the consequences of abnormal events in nuclear power plants by the use of air cleaning systems. Equipment intended for use in design basis accident and severe accident conditions is reviewed, with reference to designs used in IAEA Member States. 93 refs, 48 figs, 23 tabs

Retention of elemental 131I by activated carbons under accident conditions

International Nuclear Information System (INIS)

Deuber, H.

1984-09-01

Under simulated accident conditions (maximum temperature: 130 0 C) no significant difference was found in the retention of I-131 loaded as elemental iodine, by various fresh and aged commercial activated carbons. In all the cases, the I-131 passing through deep beds of activated carbon was in a non-elemental form. It is concluded that a minimum retention of 99.99% for elemental radioiodine, as required by the RSK guidelines for PWR accident filters, can be equally well achieved with various commercial activated carbons. (orig.) [de

Most likely failure location during severe accident conditions

International Nuclear Information System (INIS)

Rempe, J.L.; Allison, C.M.

1991-01-01

This paper describes preliminary results from which finite element calculation results are used in conjunction with analytical calculation results to predict failure in different LWR vessel designs during a severe accident. Detailed analyses are being performed to investigate the relative likelihood of a BWR vessel and drain line penetration to fail during a wide range of severe accident conditions. Analytically developed failure maps, which were developed in terms of dimensionless groups, are applied to consider geometries and materials occurring in other LWR vessel designs. Preliminary numerical analysis results indicate that if ceramic debris relocates within the BWR drain line to a distance below the lower head, the drain line will reach failure temperatures before the vessel fails. Application of failure maps for these debris conditions to other LWR geometries indicate that in-vessel tube melting will occur in either BWR or PWR vessel designs. Furthermore, if this melt is assumed to fill the entire penetration flow area, the melt is predicted to travel well below the lower head in any of the reference LWR penetrations. However, failure maps suggest the result that ex-vessel tube temperatures exceed the penetration's ultimate strength is specific to the BWR drain line because of its material composition and relatively large effective diameter for melt flow

Heat transport and afterheat removal for gas cooled reactors under accident conditions

International Nuclear Information System (INIS)

2001-01-01

The Co-ordinated Research Project (CRP) on Heat Transport and Afterheat Removal for Gas Cooled Reactors Under Accident Conditions was organized within the framework of the International Working Group on Gas Cooled Reactors (IWGGCR). This International Working Group serves as a forum for exchange of information on national programmes, provides advice to the IAEA on international co-operative activities in advanced technologies of gas cooled reactors (GCRs) and supports the conduct of these activities. Advanced GCR designs currently being developed are predicted to achieve a high degree of safety through reliance on inherent safety features. Such design features should permit the technical demonstration of exceptional public protection with significantly reduced emergency planning requirements. For advanced GCRs, this predicted high degree of safety largely derives from the ability of the ceramic coated fuel particles to retain the fission products under normal and accident conditions, the safe neutron physics behaviour of the core, the chemical stability of the core and the ability of the design to dissipate decay heat by natural heat transport mechanisms without reaching excessive temperatures. Prior to licensing and commercial deployment of advanced GCRs, these features must first be demonstrated under experimental conditions representing realistic reactor conditions, and the methods used to predict the performance of the fuel and reactor must be validated against these experimental data. Within this CRP, the participants addressed the inherent mechanisms for removal of decay heat from GCRs under accident conditions. The objective of this CRP was to establish sufficient experimental data at realistic conditions and validated analytical tools to confirm the predicted safe thermal response of advance gas cooled reactors during accidents. The scope includes experimental and analytical investigations of heat transport by natural convection conduction and thermal

Key risk indicators for accident assessment conditioned on pre-crash vehicle trajectory.

Science.gov (United States)

Shi, X; Wong, Y D; Li, M Z F; Chai, C

2018-08-01

Accident events are generally unexpected and occur rarely. Pre-accident risk assessment by surrogate indicators is an effective way to identify risk levels and thus boost accident prediction. Herein, the concept of Key Risk Indicator (KRI) is proposed, which assesses risk exposures using hybrid indicators. Seven metrics are shortlisted as the basic indicators in KRI, with evaluation in terms of risk behaviour, risk avoidance, and risk margin. A typical real-world chain-collision accident and its antecedent (pre-crash) road traffic movements are retrieved from surveillance video footage, and a grid remapping method is proposed for data extraction and coordinates transformation. To investigate the feasibility of each indicator in risk assessment, a temporal-spatial case-control is designed. By comparison, Time Integrated Time-to-collision (TIT) performs better in identifying pre-accident risk conditions; while Crash Potential Index (CPI) is helpful in further picking out the severest ones (the near-accident). Based on TIT and CPI, the expressions of KRIs are developed, which enable us to evaluate risk severity with three levels, as well as the likelihood. KRI-based risk assessment also reveals predictive insights about a potential accident, including at-risk vehicles, locations and time. Furthermore, straightforward thresholds are defined flexibly in KRIs, since the impact of different threshold values is found not to be very critical. For better validation, another independent real-world accident sample is examined, and the two results are in close agreement. Hierarchical indicators such as KRIs offer new insights about pre-accident risk exposures, which is helpful for accident assessment and prediction. Copyright © 2018 Elsevier Ltd. All rights reserved.

A radioactive waste transportation package monitoring system for normal transport and accident emergency response conditions

International Nuclear Information System (INIS)

Brown, G.S.; Cashwell, J.W.; Apple, M.L.

1993-01-01

This paper addresses spent fuel and high level waste transportation history and prospects, discusses accident histories of radioactive material transport, discusses emergency responder needs and provides a general description of the Transportation Intelligent Monitoring System (TRANSIMS) design. The key objectives of the monitoring system are twofold: (1) to facilitate effective emergency response to accidents involving a radioactive waste transportation package, while minimizing risk to the public and emergency first-response personnel, and (2) to allow remote monitoring of transportation vehicle and payload conditions to enable research into radioactive material transportation for normal and accident conditions. (J.P.N.)

Considerations on Fail Safe Design for Design Basis Accident (DBA) vs. Design Extension Condition (DEC): Lesson Learnt from the Fukushima Accident

International Nuclear Information System (INIS)

Ha, Jun Su; Kim, Sungyeop

2014-01-01

The fail safety design is referred to as an inherently safe design concept where the failure of an SSC (System, Structure or Component) leads directly to a safe condition. Usually the fail safe design has been devised based on the design basis accident (DBAs), because the nuclear safety has been assured by securing the capability to safely cope with DBAs. Currently regards have been paid to the DEC (Design Extension Condition) as an extended design consideration. Hence additional attention should be paid to the concept of the fail safe design in order to consider the DEC, accordingly. In this study, a case chosen from the Fukushima accident is studied to discuss the issue associated with the fail safe design in terms of DBA and DEC standpoints. For the fail safe design to be based both on the DBA and the DEC, a Mode Changeable Fail Safe Design (MCFSD) is proposed in this study. Additional discussions on what is needed for the MCFSD to be applied in the nuclear safety are addressed as well. One of the lessons learnt from the Fukushima accident should include considerations on the fail-safe design in a changing regulatory framework. Currently the design extension condition (DEC) including severe accidents should be considered during designing and licensing NPPs. Hence concepts on the fail safe design need to be changed to be based on not only the DBA but also the DEC. In this study, a case on a fail-safe design chosen from the Fukushima accident is studied to discuss the issue associated with the fail safe design in terms of DBA and DEC conditions. For the fail safe design to be based both on the DBA and the DEC, a Mode Changeable Fail Safe Design (MCFSD) is proposed in this study. Additional discussions on what is needed for the MCFSD to be applied in the nuclear safety are addressed as well

MCCI study for Pressurized Heavy Water Reactor under hypothetical accident condition

International Nuclear Information System (INIS)

Verma, Vishnu; Mukhopadhyay, Deb; Chatterjee, B.; Singh, R.K.; Vaze, K.K.

2011-01-01

In case of severe core damage accident in Pressurized Heavy Water Reactor (PHWR), large amount of molten corium is expected to come out into the calandria vault due to failure of calandria vessel. Molten corium at high temperature is sufficient to decompose and ablate concrete. Such attack could fail CV by basement penetration. Since containment is ultimate barrier for activity release. The Molten Core Concrete Interaction (MCCI) of the resulting pool of debris with the concrete has been identified as an important part of the accident sequence. MCCI Analysis has been carried out for PHWR for a hypothetical accident condition where total core material is considered to be relocated in calandria vault. Concrete ablation rate in vertical and radial direction is evaluated for rectangular geometry using MEDICIS module of ASTEC Code. Amount of gases released during MCCI is also evaluated. (author)

Aging, condition monitoring, and loss-of-coolant accident (LOCA) tests of class 1E electrical cables

International Nuclear Information System (INIS)

Jacobus, M.J.

1992-11-01

This report describes the results of aging, condition monitoring, and accident testing of miscellaneous cable types. Three sets of cables were aged for up to 9 months under simultaneous thermal (≅100 degrees C) and radiation (≅0.10 kGy/hr) conditions. A sequential accident consisting of high dose rate irradiation (≅6 kGy/hr) and high temperature steam followed the aging. Also exposed to the accident conditions was a fourth set of cables, which were unaged. The test results indicate that, properly installed, most of the various miscellaneous cable products tested should be able to survive an accident after 60 years for total aging doses of at least 150 kGy or higher (depending on the material) and for moderate ambient temperatures on the order of 45--55 degrees C (potentially higher or lower, depending on material specific activtion energies and total radiation doses). Mechanical measurements (primarily elongation, modulus, and density) were more effective than electrical measurements for monitoring age-related degradation

Failure Mode Estimation of Wolsong Unit 1 Containment Building with respect to Severe Accident Condition

International Nuclear Information System (INIS)

Hahm, Dae Gi; Choi, In Kil

2009-01-01

The containment buildings in a nuclear power plant (NPP) are final barriers against the exposure of harmful radiation materials at severe accident condition. Since the accident at Three Mile Island nuclear plant in 1979, it has become necessary to evaluate the internal pressure capacity of the containment buildings for the assessment of the safety of nuclear power plants. According to this necessity, many researchers including Yonezawa et al. and Hu and Lin analyzed the ultimate capacity of prestressed concrete containments subjected to internal pressure which can be occurred at sever accident condition. Especially in Wolsong nuclear power plant, the Unit 1 containment structures were constructed in the late 1970 to early 1980, so that the end of its service life will be reached in near future. Since that the complete decommission and reconstruction of the NPP may cause a huge expenses, an extension of the service time can be a cost-effective alternative. To extend the service time of NPP, an overall safety evaluation of the containment building under severe accident condition should be performed. In this study, we assessed the pressure capacity of Wolsong Unit 1 containment building under severe accident, and estimated the responses at all of the probable critical areas. Based on those results, we found the significant failure modes of Wolsong Unit 1 containment building with respect to the severe accident condition. On the other hand, for the aged NPP, the degradation of their structural performance must also be explained in the procedure of the internal pressure capacity evaluation. Therefore, in this study, we performed a parametric study on the degradation effects and evaluated the internal pressure capacity of Wolsong Unit 1 containment building with considering aging and degradation effects

Some conditions affecting the definition of design basis accidents relating to sodium/water reactions

International Nuclear Information System (INIS)

Bolt, P.R.

1984-01-01

The possible damaging effects of large sodium/water reactions on the steam generator, IHX and secondary circuit are considered. The conditions to be considered in defining the design basis accidents for these components are discussed, together with some of the assumptions that may be associated with design assessments of the scale of the accidents. (author)

Potential behavior of depleted uranium penetrators under shipping and bulk storage accident conditions

Energy Technology Data Exchange (ETDEWEB)

Mishima, J.; Parkhurst, M.A.; Scherpelz, R.I.

1985-03-01

An investigation of the potential hazard from airborne releases of depleted uranium (DU) from the Army's M829 munitions was conducted at the Pacific Northwest Laboratory. The study included: (1) assessing the characteristics of DU oxide from an April 1983 burn test, (2) postulating conditions of specific accident situations, and (3) reviewing laboratory and theoretical studies of oxidation and airborne transport of DU from accidents. Results of the experimental measurements of the DU oxides were combined with atmospheric transport models and lung and kidney exposure data to help establish reasonable exclusion boundaries to protect personnel and the public at an accident site. 121 references, 44 figures, 30 tables.

Preliminary safety analysis of the PWR with accident-tolerant fuels during severe accident conditions

International Nuclear Information System (INIS)

Wu, Xiaoli; Li, Wei; Wang, Yang; Zhang, Yapei; Tian, Wenxi; Su, Guanghui; Qiu, Suizheng; Liu, Tong; Deng, Yongjun; Huang, Heng

2015-01-01

Highlights: • Analysis of severe accident scenarios for a PWR fueled with ATF system is performed. • A large-break LOCA without ECCS is analyzed for the PWR fueled with ATF system. • Extended SBO cases are discussed for the PWR fueled with ATF system. • The accident-tolerance of ATF system for application in PWR is illustrated. - Abstract: Experience gained in decades of nuclear safety research and previous nuclear accidents direct to the investigation of passive safety system design and accident-tolerant fuel (ATF) system which is now becoming a hot research point in the nuclear energy field. The ATF system is aimed at upgrading safety characteristics of the nuclear fuel and cladding in a reactor core where active cooling has been lost, and is preferable or comparable to the current UO 2 –Zr system when the reactor is in normal operation. By virtue of advanced materials with improved properties, the ATF system will obviously slow down the progression of accidents, allowing wider margin of time for the mitigation measures to work. Specifically, the simulation and analysis of a large break loss of coolant accident (LBLOCA) without ECCS and extended station blackout (SBO) severe accident are performed for a pressurized water reactor (PWR) loaded with ATF candidates, to reflect the accident-tolerance of ATF

Spent fuel transport cask thermal evaluation under normal and accident conditions

Energy Technology Data Exchange (ETDEWEB)

Pugliese, G. [Department of Mechanical, Nuclear and Production Engineering, University of Pisa, Via Diotisalvi, no 2-56126 Pisa (Italy); Lo Frano, R., E-mail: rosa.lofrano@ing.unipi.i [Department of Mechanical, Nuclear and Production Engineering, University of Pisa, Via Diotisalvi, no 2-56126 Pisa (Italy); Forasassi, G. [Department of Mechanical, Nuclear and Production Engineering, University of Pisa, Via Diotisalvi, no 2-56126 Pisa (Italy)

2010-06-15

The casks used for transport of nuclear materials, especially the spent fuel element (SPE), must be designed according to rigorous acceptance criteria and standards requirements, e.g. the International Atomic Energy Agency ones, in order to provide protection to people and environment against radiation exposure particularly in a severe accident scenario. The aim of this work was the evaluation of the integrity of a spent fuel cask under both normal and accident scenarios transport conditions, such as impact and rigorous fire events, in according to the IAEA accident test requirements. The thermal behaviour and the temperatures distribution of a Light Water Reactor (LWR) spent fuel transport cask are presented in this paper, especially with reference to the Italian cask designed by AGN, which was characterized by a cylindrical body, with water or air inside the internal cavity, and two lateral shock absorbers. Using the finite element code ANSYS a series of thermal analyses (steady-state and transient thermal analyses) were carried out in order to obtain the maximum fuel temperature and the temperatures field in the body of the cask, both in normal and in accidents scenario, considering all the heat transfer modes between the cask and the external environment (fire in the test or air in the normal conditions) as well as inside the cask itself. In order to follow the standards requirements, the thermal analyses in accidents scenarios were also performed adopting a deformed shape of the shock absorbers to simulate the mechanical effects of a previous IAEA 9 m drop test event. Impact tests on scale models of the shock absorbers have already been conducted in the past at the Department of Mechanical, Nuclear and Production Engineering, University of Pisa, in the '80s. The obtained results, used for possible new licensing approval purposes by the Italian competent Authority of the cask for PWR spent fuel cask transport by the Italian competent Authority, are

Behaviour of organic iodides under pwr accident conditions

International Nuclear Information System (INIS)

Alm, M.

1982-01-01

Laboratory experiments were performed to study the behaviour of radioactive methyl iodide under PWR loss-of-coolant conditions. The pressure relief equipment consisted of an autoclave for simulating the primary circuit and of an expansion vessel for simulating the conditions after a rupture in the reactor coolant system. After pressure relief, the composition of the CH 3 sup(127/131)I-containing steam-air mixture within the expansion vessel was analysed at 80 0 C over a period of 42 days. On the basis of the values measured and of data taken from the literature, both qualitative and quantitative assessments have been made as to the behaviour of radioactive methyl iodide in the event of loss-of-coolant accidents. (author)

Preliminary insights of the impact of steady state uncertainties on fuel rod response to an RIA

International Nuclear Information System (INIS)

Herranz, Luis E.; Huguet, Anne

2013-01-01

Nuclear fuel cycles are driven to higher burn-ups under the nowadays more demanding operational conditions. The operational safety limits that ensure the long-term core coolability are set through the analysis of the design basis accidents, RIA scenarios. These analyses are mainly performed through computer codes that encapsulate the present understanding of fuel behavior under such events. They assess safety margins and therefore their accuracy is of utmost interest. Their predictability is extended and validated through separate effect and integral experiments data. Given the complexity of working phenomena under RIA conditions, neither existing thermo-mechanical models nor rod state characterization at the moment of power pulse reflect exactly reality. So, it is essential to know how these deviations influence code predictions. This study illustrates how uncertainties related to pre-transient rod characterization affect the estimates of nuclear fuel behavior during the transient. In order to do so, the RIA scenario of the CIP0-1 test (CABRI program) has been analyzed with FRAPCON-3 (steady state irradiation) and FRAPTRAN 1.4 (transient) codes. The input uncertainties have been propagated through the codes by following a deterministic approach. This work is framed within the CSN-CIEMAT agreement on 'Thermo-Mechanical Behavior of the Nuclear Fuel at High Burnup'. (authors)

Interaction of radionuclides in severe accident conditions

International Nuclear Information System (INIS)

Nagrale, Dhanesh B.; Bera, Subrata; Deo, Anuj Kumar; Paul, U.K.; Prasad, M.; Gaikwad, A.J.

2015-01-01

Nuclear power plants are designed with inherent engineering safety systems and associated operational procedures that provide an in-depth defence against accidents. Radionuclides such as Iodine, Cesium, Tellurium, Barium, Strontium, Rubidium, Molybdenum and many others may get released during a severe accident. Among these, Iodine, one of the fission products, behaviour is significant for the analysis of severe accident consequences because iodine is a chemically more active to the potential components released to the environment. During severe accident, Iodine is released and transported in aqueous, organic and inorganic forms. Iodine release from fuel, iodine transport in primary coolant system, containment, and reaction with control rods are some of the important phases in a severe accident scenario. The behaviour of iodine is governed by aerosol physics, depletion mechanisms gravitational settling, diffusiophoresis and thermophoresis. The presence of gaseous organic compounds and oxidizing compounds on iodine, reactions of aerosol iodine with boron and formation of cesium iodide which results in more volatile iodine release in containment play significant roles. Water radiolysis products due to presence of dissolved impurities, chloride ions, organic impurities should be considered while calculating iodine release. Containment filtered venting system (CFVS) consists of venturi scrubber and a scrubber tank which is dosed with NaOH and NaS_2O_3 in water where iodine will react with the chemicals and convert into NaI and Na_2SO_4. This paper elaborates the issues with respect to interaction of radionuclides and its consideration in modeling of severe accident. (author)

Determination of Optimal Flow Paths for Safety Injection According to Accident Conditions

Energy Technology Data Exchange (ETDEWEB)

Yoo, Kwae Hwan; Kim, Ju Hyun; Kim, Dong Yeong; Na, Man Gyun [Chosun Univ., Gwangju (Korea, Republic of); Hur, Seop; Kim, Changhwoi [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

In case severe accidents happen, major safety parameters of nuclear reactors are rapidly changed. Therefore, operators are unable to respond appropriately. This situation causes the human error of operators that led to serious accidents at Chernobyl. In this study, we aimed to develop an algorithm that can be used to select the optimal flow path for cold shutdown in serious accidents, and to recover an NPP quickly and efficiently from the severe accidents. In order to select the optimal flow path, we applied a Dijkstra algorithm. The Dijkstra algorithm is used to find the path of minimum total length between two given nodes and needs a weight (or length) matrix. In this study, the weight between nodes was calculated from frictional and minor losses inside pipes. That is, the optimal flow path is found so that the pressure drop between a starting node (water source) and a destination node (position that cooling water is injected) is minimized. In case a severe accident has happened, if we inject cooling water through the optimized flow path, then the nuclear reactor will be safely and effectively returned into the cold shutdown state. In this study, we have analyzed the optimal flow paths for safety injection as a preliminary study for developing an accident recovery system. After analyzing the optimal flow path using the Dijkstra algorithm, and the optimal flow paths were selected by calculating the head loss according to path conditions.

Noble gas control room accident filtration system for severe accident conditions N-CRAFT. System design

International Nuclear Information System (INIS)

Hill, Axel

2014-01-01

Severe accidents might cause the release of airborne radioactive substances to the environment of the NPP. This can either be due to leakages of the containment or due to a filtered containment venting in order to ensure the overall integrity of the containment. During the containment venting process aerosols and iodine can be retained by the FCVS which prevents long term ground contamination. Noble gases are not retainable by the FCVS. From this it follows that a large amount of radioactive noble gases (e.g. xenon, krypton) might be present in the nearby environment of the plant dominating the activity release, depending on the venting procedure and the weather conditions. Accident management measures are necessary in case of severe accidents and the prolonged stay of staff inside the main control room (MCR) or emergency response center (ERC) is essential. Therefore, the in leakage and contamination of the MRC and ERC with airborne activity has to be prevented. The radiation exposure of the crises team needs to be minimized. The entrance of noble gases cannot be sufficiently prevented by the conventional air filtration systems such as HEPA filters and iodine absorbers. With the objective to prevent an unacceptable contamination of the MCR/ERC atmosphere by noble gases AREVA GmbH has developed a noble gas retention system. The noble gas control room accident filtration system CRAFT is designed for this case and provides supply of fresh air to the MCR/ERC without time limitation. The retention process of the system is based on the dynamic adsorption of noble gases on activated carbon. The system consists of delay lines (carbon columns) which are operated by a continuous and simultaneous adsorption and desorption process. These cycles ensure a periodic load and flushing of the delay lines retaining the noble gases from entering the MCR. CRAFT allows a minimization of the dose rate inside MCR/ERC and ensures a low radiation exposure to the staff on shift maintaining

Development of stable walking robot for accident condition monitoring on uneven floors in a nuclear power plant

Energy Technology Data Exchange (ETDEWEB)

Kim, Jong Seog; Jang, You Hyun [Central Research Institute of Korea Hydro and Nuclear Power Company, Daejeon (Korea, Republic of)

2017-04-15

Even though the potential for an accident in nuclear power plants is very low, multiple emergency plans are necessary because the impact of such an accident to the public is enormous. One of these emergency plans involves a robotic system for investigating accidents under conditions of high radiation and contaminated air. To develop a robot suitable for operation in a nuclear power plant, we focused on eliminating the three major obstacles that challenge robots in such conditions: the disconnection of radio communication, falling on uneven floors, and loss of localization. To solve the radio problem, a Wi-Fi extender was used in radio shadow areas. To reinforce the walking, we developed two- and four-leg convertible walking, a floor adaptive foot, a roly-poly defensive falling design, and automatic standing recovery after falling methods were developed. To allow the robot to determine its location in the containment building, a bar code landmark reading method was chosen. When a severe accident occurs, this robot will be useful for accident condition monitoring. We also anticipate the robot can serve as a workman aid in a high radiation area during normal operations.

Primary pump vibration under accident conditions

International Nuclear Information System (INIS)

Guthrie, B.M.; Currie, T.C.

1984-06-01

This report presents the results of an international survey on the subject of vibration in nuclear primary coolant pumps due to two-phase flow, accident conditions. The literature search also revealed few Canadian references other than those of Ontario Hydro. Ontario Hydro's work has been extensive. Confidence in the mechanical integrity of the pumpsets is good, given the extent of the testing. However, conclusions with respect to piping integrity and thermal-hydraulic performance are difficult to determine due to the inexact geometry of the piping and the difficulties in estimating fluid conditions at the pump. The tests help to understand the phenomena and provide background information for analysis, but should be applied with caution to plant analyses. Much of the discussion in the report relates to pump head instability. This is perceived to be the most important flow regime causing vibration, as attested by the emphasis of the reviewed literature. A method for quantitative assessment of the forcing functions acting on the pump-piping system due to void generation and collapse is recommended. A relatively fundamental analytical approach is proposed, supplemented by reduced scale testing in the latter stages. 151 refs

Qualitative analysis of the man-organization system in accident conditions for nuclear installations

International Nuclear Information System (INIS)

Farcasiu, Mita; Prisecaru, Ilie

2010-01-01

In this paper a model of the human performance investigation of accident conditions in the operation of the nuclear installation is developed. A framework for analyses of the human action in the man-organization system context is achieved. The goal of this model is to identify the possible roots causing human errors which could occur during the evolution of the accident by the qualitative analysis of the interfaces in man-organization system. These interfaces represent the main elements which characterize the implication of the organization in human performance. The results of this paper are the interfaces of the man-organization and their circumstances in which human performance could fail. Also, another result is a pre-designed framework which could help in the investigation of an accident. (authors)

Application of uncertainty analysis method for calculations of accident conditions for RP AES-2006

International Nuclear Information System (INIS)

Zajtsev, S.I.; Bykov, M.A.; Zakutaev, M.O.; Siryapin, V.N.; Petkevich, I.G.; Siryapin, N.V.; Borisov, S.L.; Kozlachkov, A.N.

2015-01-01

An analysis of some accidents using the uncertainly assessment methods is given. The list of the variable parameters incorporated the model parameters of the computer codes, initial and boundary conditions of reactor plant, neutronics. On the basis of the performed calculations of the accident conditions using the statistical method, errors assessment is presented in the determination of the main parameters comparable with the acceptance criteria. It was shown that in the investigated accidents the values of the calculated parameters with account for their error obtained from TRAP-KS and KORSAR/GP Codes do not exceed the established acceptance criteria. Besides, these values do not exceed the values obtained in the conservative calculations. A possibility in principle of the actual application of the method of estimation of uncertainty was shown to justify the safety of WWER AES-2006 using the thermal-physical codes KORSAR/GP and TRAP-KS, PANDA and SUSA programs [ru

Clinical usefulness of creatine Kinase BB determination by a Ria method in serum of patients with cerebrovascular accidents

Energy Technology Data Exchange (ETDEWEB)

Nuti, A; Giraldi, C; Piccini, P; Bonucelli, U; Clerico, A; Del Chicca, M G

1988-01-01

The measurement of creatine kinase BB isoenzyme (CK-BB) using RIA methods could have diagnostic utility as a biological marker of cerebral damage. The aim of the present study is to evaluate whether frequent sampling (4 samples/day for 3 days) permits a better correlation between serum CK/sub B/B values and the clinical outcomes of patients with cerebrovascular accidents. 16 in-patients (12 men and 4 women) with stroke (15 of an ischemic nature and 1 hemorrhagic) have benn studied. The presence of stroke was confirmed by clinical symptoms and by CAT results. Blood samples were drawn at 6 and 12 a.m. and at 6 and 12 p.m. over 3 consecutive days after hospitalization. Values of serum CK-BB above the normal range (>7 ng/ml) were found in the 5 of the 16 (31.3%) patients studied. The mean CK-BB value observed in the patients' group was significantly higher than that found in a group of 112 control subjects (controls, mean+-SD=2.1+-1.7 ng/ml vs patients 3.3+-3.4 ng/ml, unpaired t-test p<0.025). We observed a very wide range of serum CKBB levels in most of the patients studied. Some prominent peaks of CK-BB concetrations were found in patients' outcame (Spearman correlation coefficient r-s=0.618, p<0,01). Although our results indicate that the measurement of CK-BB concentrations cannot be considered a sensitive marker of stroke, the significant correlation between serum CK-BB values and outcome suggests that high CK-BB levels could be a sign of worse prognosis in patients with cerebrovascular accidents. 24 refs.

Clinical usefulness of creatine Kinase BB determination by a Ria method in serum of patients with cerebrovascular accidents

International Nuclear Information System (INIS)

Nuti, A.; Giraldi, C.; Piccini, P.; Bonucelli, U.; Clerico, A.; Del Chicca, M. G.

1988-01-01

The measurement of creatine kinase BB isoenzyme (CK-BB) using RIA methods could have diagnostic utility as a biological marker of cerebral damage. The aim of the present study is to evaluate whether frequent sampling (4 samples/day for 3 days) permits a better correlation between serum CK B B values and the clinical outcomes of patients with cerebrovascular accidents. 16 in-patients (12 men and 4 women) with stroke (15 of an ischemic nature and 1 hemorrhagic) have benn studied. The presence of stroke was confirmed by clinical symptoms and by CAT results. Blood samples were drawn at 6 and 12 a.m. and at 6 and 12 p.m. over 3 consecutive days after hospitalization. Values of serum CK-BB above the normal range (>7 ng/ml) were found in the 5 of the 16 (31.3%) patients studied. The mean CK-BB value observed in the patients' group was significantly higher than that found in a group of 112 control subjects (controls, mean+-SD=2.1+-1.7 ng/ml vs patients 3.3+-3.4 ng/ml, unpaired t-test p<0.025). We observed a very wide range of serum CKBB levels in most of the patients studied. Some prominent peaks of CK-BB concetrations were found in patients' outcame (Spearman correlation coefficient r-s=0.618, p<0,01). Although our results indicate that the measurement of CK-BB concentrations cannot be considered a sensitive marker of stroke, the significant correlation between serum CK-BB values and outcome suggests that high CK-BB levels could be a sign of worse prognosis in patients with cerebrovascular accidents

Postulated accident conditions for air cleaning systems and radiological dose assessments for containment options

International Nuclear Information System (INIS)

Hilliard, R.K.; Postma, A.K.

1975-01-01

Ambient conditions and performance requirements for emergency air cleaning systems applicable to commercial LMFBR plants were studied. The focus of this study centered on aerosol removal under hypothetical core disruptive accident conditions. Effort completed includes a review of air cleaning systems related to LMFBR plants, selection of three reference containment system designs, postulation of the EACS design basis accident (EACS-DBA), analysis of thermal conditions resulting from the DBA, analysis of aerosol transport behavior following the DBA, and an estimate of bone dose at the site boundary for each of the reference plant designs. Reference plant concepts were a single containment system (e.g., FFTF), a double containment system (e.g., CRBRP with closed head compartment), and a containment-confinement design in which an inerted, sealed primary volume was located within a ventilated building whose exhaust was filtered. The reference design basis accident selected here involved release to the inner containment system of 1 percent of non-volatile solids and plutonium, 25 percent of core halogens, 25 percent of core volatile solids, 100 percent of core noble gases, 68 lbs of sodium vapor and 5000 lbs of liquid sodium. 13 references. (U.S.)

Simulation of reactivity-initiated accident transients on UO2-M5® fuel rods with ALCYONE V1.4 fuel performance code

Directory of Open Access Journals (Sweden)

Isabelle Guénot-Delahaie

2018-03-01

Full Text Available The ALCYONE multidimensional fuel performance code codeveloped by the CEA, EDF, and AREVA NP within the PLEIADES software environment models the behavior of fuel rods during irradiation in commercial pressurized water reactors (PWRs, power ramps in experimental reactors, or accidental conditions such as loss of coolant accidents or reactivity-initiated accidents (RIAs. As regards the latter case of transient in particular, ALCYONE is intended to predictively simulate the response of a fuel rod by taking account of mechanisms in a way that models the physics as closely as possible, encompassing all possible stages of the transient as well as various fuel/cladding material types and irradiation conditions of interest. On the way to complying with these objectives, ALCYONE development and validation shall include tests on PWR-UO2 fuel rods with advanced claddings such as M5® under “low pressure–low temperature” or “high pressure–high temperature” water coolant conditions.This article first presents ALCYONE V1.4 RIA-related features and modeling. It especially focuses on recent developments dedicated on the one hand to nonsteady water heat and mass transport and on the other hand to the modeling of grain boundary cracking-induced fission gas release and swelling. This article then compares some simulations of RIA transients performed on UO2-M5® fuel rods in flowing sodium or stagnant water coolant conditions to the relevant experimental results gained from tests performed in either the French CABRI or the Japanese NSRR nuclear transient reactor facilities. It shows in particular to what extent ALCYONE—starting from base irradiation conditions it itself computes—is currently able to handle both the first stage of the transient, namely the pellet-cladding mechanical interaction phase, and the second stage of the transient, should a boiling crisis occur.Areas of improvement are finally discussed with a view to simulating and

Behaviour of gas cooled reactor fuel under accident conditions

International Nuclear Information System (INIS)

1991-11-01

The Specialists Meeting on Behaviour of Gas Cooled Reactor Fuel under Accident Conditions was convened by the International Atomic Energy Agency on the recommendation of the International Working Group on Gas Cooled Reactors. The purpose of the meeting was to provide an international forum for the review of the development status and for the discussion on the behaviour of gas cooled reactor fuel under accident conditions and to identify areas in which additional research and development are still needed and where international co-operation would be beneficial for all involved parties. The meeting was attended by 45 participants from France, Germany, Japan, Switzerland, the Union of Soviet Socialists Republics, the United Kingdom, the United States of America, CEC and the IAEA. The meeting was subdivided into five technical sessions: Summary of Current Research and Development Programmes for Fuel; Fuel Manufacture and Quality Control; Safety Requirements; Modelling of Fission Product Release - Part I and Part II; Irradiation Testing/Operational Experience with Fuel Elements; Behaviour at Depressurization, Core Heat-up, Power Transients; Water/Steam Ingress - Part I and Part II. 22 papers were presented. A separate abstract was prepared for each of these papers. At the end of the meeting a round table discussion was held on Directions for Future R and D Work and International Co-operation. Refs, figs and tabs

Status of USNRC research on fuel behavior under accident conditions

International Nuclear Information System (INIS)

Johnston, W.V.

1976-01-01

The program of the Fuel Behaviour Research is directed at providing a detailed understanding of the response of nuclear fuel assemblies to off-normal or accident conditions. This understanding is expressed in physical and analytical correlations which are incorporated into computer codes. The results of these experiments and the resulting codes are available to the licensing authorities for use in evaluating utility submissions. (orig.) [de

Assessment of Core Failure Limits for Light Water Reactor Fuel under Reactivity Initiated Accidents

International Nuclear Information System (INIS)

Jernkvist, Lars Olof; Massih, Ali R.

2004-12-01

Core failure limits for high-burnup light water reactor UO 2 fuel rods, subjected to postulated reactivity initiated accidents (RIAs), are here assessed by use of best-estimate computational methods. The considered RIAs are the hot zero power rod ejection accident (HZP REA) in pressurized water reactors and the cold zero power control rod drop accident (CZP CRDA) in boiling water reactors. Burnup dependent core failure limits for these events are established by calculating the fuel radial average enthalpy connected with incipient fuel pellet melting for fuel burnups in the range of 30 to 70 MWd/kgU. The postulated HZP REA and CZP CRDA result in lower enthalpies for pellet melting than RIAs that take place at rated power. Consequently, the enthalpy thresholds presented here are lower bounds to RIAs at rated power. The calculations are performed with best-estimate models, which are applied in the FRAPCON-3.2 and SCANAIR-3.2 computer codes. Based on the results of three-dimensional core kinetics analyses, the considered power transients are simulated by a Gaussian pulse shape, with a fixed width of either 25 ms (REA) or 45 ms (CRDA). Notwithstanding the differences in postulated accident scenarios between the REA and the CRDA, the calculated core failure limits for these two events are similar. The calculated enthalpy thresholds for fuel pellet melting decrease gradually with fuel burnup, from approximately 960 J/gUO 2 at 30 MWd/kgU to 810 J/gUO 2 at 70 MWd/kgU. The decline is due to depression of the UO 2 melting temperature with increasing burnup, in combination with burnup related changes to the radial power distribution within the fuel pellets. The presented fuel enthalpy thresholds for incipient UO 2 melting provide best-estimate core failure limits for low- and intermediate-burnup fuel. However, pulse reactor tests on high-burnup fuel rods indicate that the accumulation of gaseous fission products within the pellets may lead to fuel dispersal into the coolant at

Causal Factors and Adverse Conditions of Aviation Accidents and Incidents Related to Integrated Resilient Aircraft Control

Science.gov (United States)

Reveley, Mary S.; Briggs, Jeffrey L.; Evans, Joni K.; Sandifer, Carl E.; Jones, Sharon Monica

2010-01-01

The causal factors of accidents from the National Transportation Safety Board (NTSB) database and incidents from the Federal Aviation Administration (FAA) database associated with loss of control (LOC) were examined for four types of operations (i.e., Federal Aviation Regulation Part 121, Part 135 Scheduled, Part 135 Nonscheduled, and Part 91) for the years 1988 to 2004. In-flight LOC is a serious aviation problem. Well over half of the LOC accidents included at least one fatality (80 percent in Part 121), and roughly half of all aviation fatalities in the studied time period occurred in conjunction with LOC. An adverse events table was updated to provide focus to the technology validation strategy of the Integrated Resilient Aircraft Control (IRAC) Project. The table contains three types of adverse conditions: failure, damage, and upset. Thirteen different adverse condition subtypes were gleaned from the Aviation Safety Reporting System (ASRS), the FAA Accident and Incident database, and the NTSB database. The severity and frequency of the damage conditions, initial test conditions, and milestones references are also provided.

Hydrogen-control systems for severe LWR accident conditions - a state-of-technology report

International Nuclear Information System (INIS)

Hilliard, R.K.; Postma, A.K.; Jeppson, D.W.

1983-03-01

This report reviews the current state of technology regarding hydrogen safety issues in light water reactor plants. Topics considered in this report relate to control systems and include combustion prevention, controlled combustion, minimization of combustion effects, combination of control concepts, and post-accident disposal. A companion report addresses hydrogen generation, distribution, and combustion. The objectives of the study were to identify the key safety issues related to hydrogen produced under severe accident conditions, to describe the state of technology for each issue, and to point out ongoing programs aimed at resolving the open issues

Comparative study of heterogeneous and homogeneous LMFBR cores in some accident conditions

International Nuclear Information System (INIS)

Renard, A.; Evrard, G.

1978-01-01

An heterogeneous design and a homogeneous one of a LMFBR core with the same power and similar dimensions are compared from the safety point-of-view. The comparison is performed for several accident conditions, such as Loss-of-Flow and Transient Overpower, with the same failure criteria and model assumptions for both cores. Qualitative trends are deduced from the behaviour of the core designs in the investigated transient conditions. (author)

Potential for containment leak paths through electrical penetration assemblies under severe accident conditions

International Nuclear Information System (INIS)

Sebrell, W.

1983-07-01

The leakage behavior of containments beyond design conditions and knowledge of failure modes is required for evaluation of mitigation strategies for severe accidents, risk studies, emergency preparedness planning, and siting. These studies are directed towards assessing the risk and consequences of severe accidents. An accident sequence analysis conducted on a Boiling Water Reactor (BWR), Mark I (MK I), indicated very high temperatures in the dry-well region, which is the location of the majority of electrical penetration assemblies. Because of the high temperatures, it was postulated in the ORNL study that the sealants would fail and all the electrical penetration assemblies would leak before structural failure would occur. Since other containments had similar electrical penetration assemblies, it was concluded that all containments would experience the same type of failure. The results of this study, however, show that this conclusion does not hold for PWRs because in the worst accident sequence, the long time containment gases stabilize to 350 0 F. BWRs, on the other hand, do experience high dry-well temperatures and have a higher potential for leakage

Multi-phase model development to assess RCIC system capabilities under severe accident conditions

Energy Technology Data Exchange (ETDEWEB)

Kirkland, Karen Vierow [Texas A & M Univ., College Station, TX (United States); Ross, Kyle [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Beeny, Bradley [Texas A & M Univ., College Station, TX (United States); Luthman, Nicholas [Texas A& M Engineering Experiment Station, College Station, TX (United States); Strater, Zachary [Texas A & M Univ., College Station, TX (United States)

2017-12-23

The Reactor Core Isolation Cooling (RCIC) System is a safety-related system that provides makeup water for core cooling of some Boiling Water Reactors (BWRs) with a Mark I containment. The RCIC System consists of a steam-driven Terry turbine that powers a centrifugal, multi-stage pump for providing water to the reactor pressure vessel. The Fukushima Dai-ichi accidents demonstrated that the RCIC System can play an important role under accident conditions in removing core decay heat. The unexpectedly sustained, good performance of the RCIC System in the Fukushima reactor demonstrates, firstly, that its capabilities are not well understood, and secondly, that the system has high potential for extended core cooling in accident scenarios. Better understanding and analysis tools would allow for more options to cope with a severe accident situation and to reduce the consequences. The objectives of this project were to develop physics-based models of the RCIC System, incorporate them into a multi-phase code and validate the models. This Final Technical Report details the progress throughout the project duration and the accomplishments.

Network conditioning under conflicting goals: Accident causation

International Nuclear Information System (INIS)

Jouse, W.C.

1992-01-01

Networks based on the Barto-Sutton architecture (BSA) of neural-like elements have an information-processing structure that is analogous to the cognitive structure of a human. Given a set of explicitly stated rules of conduct, such networks develop a set of skills that is capable of satisfying the rules. In this sense, the network acts as a translator of rules into skill-based behavior. The BSA acquires its skills through casual, correlation-based scheduling. Stated briefly, it first constructs an internal representation, or model, of the rules of conduct, and then uses the model to correct deficiencies in its skill. It learns in a manner that closely resembles classical conditioning, shifting the onset of signals associated with unconditioned stimuli forward in time to coincide with the onset of conditioning stimuli. The low-level positive reinforcement the network receives from enhancing its operational efficiency is immediate and direct. In the absence of countervailing influences, this continuous pressure is sufficient to discount the recollection of past failures and leads to accidents with a predictable regularity

Accident identification system with automatic detection of abnormal condition using quantum computation

International Nuclear Information System (INIS)

Nicolau, Andressa dos Santos; Schirru, Roberto; Lima, Alan Miranda Monteiro de

2011-01-01

Transient identification systems have been proposed in order to maintain the plant operating in safe conditions and help operators in make decisions in emergency short time interval with maximum certainty associated. This article presents a system, time independent and without the use of an event that can be used as a starting point for t = 0 (reactor scram, for instance), for transient/accident identification of a pressurized water nuclear reactor (PWR). The model was developed in order to be able to recognize the normal condition and three accidents of the design basis list of the Nuclear Power Plant Angra 2, postulated in the Final Safety Analysis Report (FSAR). Were used several sets of process variables in order to establish a minimum set of variables considered necessary and sufficient. The optimization step of the identification algorithm is based upon the paradigm of Quantum Computing. In this case, the optimization metaheuristic Quantum Inspired Evolutionary Algorithm (QEA) was implemented and works as a data mining tool. The results obtained with the QEA without the time variable are compatible to the techniques in the reference literature, for the transient identification problem, with less computational effort (number of evaluations). This system allows a solution that approximates the ideal solution, the Voronoi Vectors with only one partition for the classes of accidents with robustness. (author)

Structural Evaluation on HIC Transport Packaging under Accident Conditions

International Nuclear Information System (INIS)

Chung, Sung Hwan; Kim, Duck Hoi; Jung, Jin Se; Yang, Ke Hyung; Lee, Heung Young

2005-01-01

HIC transport packaging to transport a high integrity container(HIC) containing dry spent resin generated from nuclear power plants is to comply with the regulatory requirements of Korea and IAEA for Type B packaging due to the high radioactivity of the content, and to maintain the structural integrity under normal and accident conditions. It must withstand 9 m free drop impact onto an unyielding surface and 1 m drop impact onto a mild steel bar in a position causing maximum damage. For the conceptual design of a cylindrical HIC transport package, three dimensional dynamic structural analysis to ensure that the integrity of the package is maintained under all credible loads for 9 m free drop and 1 m puncture conditions were carried out using ABAQUS code.

Development of advanced claddings for suppressing the hydrogen emission in accident conditions. Development of advanced claddings for suppressing the hydrogen emission in the accident condition

International Nuclear Information System (INIS)

Park, Jeong-Yong; KIM, Hyun-Gil; JUNG, Yang-Il; PARK, Dong-Jun; KOO, Yang-Hyun

2013-01-01

The development of accident-tolerant fuels can be a breakthrough to help solve the challenge facing nuclear fuels. One of the goals to be reached with accident-tolerant fuels is to reduce the hydrogen emission in the accident condition by improving the high-temperature oxidation resistance of claddings. KAERI launched a new project to develop the accident-tolerant fuel claddings with the primary objective to suppress the hydrogen emission even in severe accident conditions. Two concepts are now being considered as hydrogen-suppressed cladding. In concept 1, the surface modification technique was used to improve the oxidation resistance of Zr claddings. Like in concept 2, the metal-ceramic hybrid cladding which has a ceramic composite layer between the Zr inner layer and the outer surface coating is being developed. The high-temperature steam oxidation behaviour was investigated for several candidate materials for the surface modification of Zr claddings. From the oxidation tests carried out in 1 200 deg. C steam, it was found that the high-temperature steam oxidation resistance of Cr and Si was much higher than that of zircaloy-4. Al 3 Ti-based alloys also showed extremely low-oxidation rate compared to zircaloy-4. One important part in the surface modification is to develop the surface coating technology where the optimum process needs to be established depending on the surface layer materials. Several candidate materials were coated on the Zr alloy specimens by a laser beam scanning (LBS), a plasma spray (PS) and a PS followed by LBS and subject to the high-temperature steam oxidation test. It was found that Cr and Si coating layers were effective in protecting Zr-alloys from the oxidation. The corrosion behaviour of the candidate materials in normal reactor operation condition such as 360 deg. C water will be investigated after the screening test in the high-temperature steam. The metal-ceramic hybrid cladding consisted of three major parts; a Zr liner, a

Criticality accident of nuclear fuel facility. Think back on JCO criticality accident

International Nuclear Information System (INIS)

Naito, Keiji

2003-09-01

This book is written in order to understand the fundamental knowledge of criticality safety or criticality accident of nuclear fuel facility by the citizens. It consists of four chapters such as critical conditions and criticality accident of nuclear facility, risk of criticality accident, prevention of criticality accident and a measure at an occurrence of criticality accident. A definition of criticality, control of critical conditions, an aspect of accident, a rate of incident, damage, three sufferers, safety control method of criticality, engineering and administrative control, safety design of criticality, investigation of failure of safety control of JCO criticality accident, safety culture are explained. JCO criticality accident was caused with intention of disregarding regulation. It is important that we recognize the correct risk of criticality accident of nuclear fuel facility and prevent disasters. On the basis of them, we should establish safety culture. (S.Y.)

Role of Winter Weather Conditions and Slipperiness on Tourists’ Accidents in Finland

Directory of Open Access Journals (Sweden)

Élise Lépy

2016-08-01

Full Text Available (1 Background: In Finland, slippery snowy or icy ground surface conditions can be quite hazardous to human health during wintertime. We focused on the impacts of the variability in weather conditions on tourists’ health via documented accidents during the winter season in the Sotkamo area. We attempted to estimate the slipping hazard in a specific context of space and time focusing on the weather and other possible parameters, responsible for fluctuations in the numbers of injuries/accidents; (2 Methods: We used statistical distributions with graphical illustrations to examine the distribution of visits to Kainuu Hospital by non-local patients and their characteristics/causes; graphs to illustrate the distribution of the different characteristics of weather conditions; questionnaires and interviews conducted among health care and safety personnel in Sotkamo and Kuusamo; (3 Results: There was a clear seasonal distribution in the numbers and types of extremity injuries of non-local patients. While the risk of slipping is emphasized, other factors leading to injuries are evaluated; and (4 Conclusions: The study highlighted the clear role of wintery weather conditions as a cause of extremity injuries even though other aspects must also be considered. Future scenarios, challenges and adaptive strategies are also discussed from the viewpoint of climate change.

A dynamic model for the study of evacuation under accident conditions

International Nuclear Information System (INIS)

Boeri, G.C.; Caracciolo, R.; Sepede, M.; Casiroli, F.; Rodriguez, R.

1987-01-01

Information techniques and models are being used to simulate the evacuation of people living around a nuclear power plant and these methods are being increasingly used for planning purposes. In this study vehicular mobility on a complex road network following an accident has been considered and applied to the specifications of the emergency plans. Simulation tests of the mobility relevant to different combinations of time and meteorological conditions have been undertaken through use of the computer code TRIPS in order to assess the impact on the road network of an accident situation and the preparedness measures. The study has led to a description of the accessibility time curves related to the population gathering centres and has enabled identification of the best routes in order to achieve the minimum travel time. (author)

Investigation of air cleaning system response to accident conditions

International Nuclear Information System (INIS)

Andrae, R.W.; Bolstad, J.W.; Foster, R.D.; Gregory, W.S.; Horak, H.L.; Idar, E.S.; Martin, R.A.; Ricketts, C.I.; Smith, P.R.; Tang, P.K.

1980-01-01

Air cleaning system response to the stress of accident conditions are being investigated. A program overview and hghlight recent results of our investigation are presented. The program includes both analytical and experimental investigations. Computer codes for predicting effects of tornados, explosions, fires, and material transport are described. The test facilities used to obtain supportive experimental data to define structural integrity and confinement effectiveness of ventilation system components are described. Examples of experimental results for code verification, blower response to tornado transients, and filter response to tornado and explosion transients are reported

Fuel Accident Condition Simulator (FACS) Furnace for Post-Irradiation Heating Tests of VHTR Fuel Compacts

Energy Technology Data Exchange (ETDEWEB)

Paul A Demkowicz; Paul Demkowicz; David V Laug

2010-10-01

Abstract –Fuel irradiation testing and post-irradiation examination are currently in progress as part of the Next Generation Nuclear Plant Fuels Development and Qualification Program. The PIE campaign will include extensive accident testing of irradiated very high temperature reactor fuel compacts to verify fission product retention characteristics at high temperatures. This work will be carried out at both the Idaho National Laboratory (INL) and the Oak Ridge National Laboratory, beginning with accident tests on irradiated fuel from the AGR-1 experiment in 2010. A new furnace system has been designed, built, and tested at INL to perform high temperature accident tests. The Fuel Accident Condition Simulator furnace system is designed to heat fuel specimens at temperatures up to 2000°C in helium while monitoring the release of volatile fission metals (e.g. Cs, Ag, Sr, Eu, and I) and fission gases (Kr, Xe). Fission gases released from the fuel to the sweep gas are monitored in real time using dual cryogenic traps fitted with high purity germanium detectors. Condensable fission products are collected on a plate attached to a water-cooled cold finger that can be exchanged periodically without interrupting the test. Analysis of fission products on the condensation plates involves dry gamma counting followed by chemical analysis of selected isotopes. This paper will describe design and operational details of the Fuel Accident Condition Simulator (FACS) furnace system, as well as preliminary system calibration results.

Living conditions in the contaminated territories of Bielorussia 8 years after the Chernobyl accident

International Nuclear Information System (INIS)

Heriard-Dubreuil, G.; Girard, P.

1997-01-01

Living conditions in the contaminated territories of Bielorussia after the Chernobyl accident: evaluation of the situation in the district of Chetchersk in Bielorussia. This article presents an analysis of the social and economic aspects of radiological protection in the territories contaminated by the Chernobyl accident. It is based on the results of two surveys performed in 1994 on the living conditions of the inhabitants of a territorial community located in Bielorussia, 180 km north of Chernobyl. The first part presents the radiological post-accident situation of the district, together with an analysis of this situation's demographic impact since 1986. The second part presents a description of the modes of exposure of the inhabitants of the contaminated territories and an assessment of he various countermeasures programmes initiated by the authorities in the legislative framework of 1991. The last part addresses the economic aspects of the Chetchersk district and an evaluation of the consequences of the radiological situation on the economic, and above all agricultural, activities of the district.The conclusion highlights the difficulties that face the Byelorussian authorities today. The now definitive presence of inhabitants in a durably contaminated environment poses a new category of problems. The objectives of radiological protection have to be reshaped within a set of constraints of different types, notably social and economic. The development of radiological safety cannot be dissociated from a return to quality living in these territories. This necessarily entails re-establishing a climate of social confidence. The initial legislative plan for post-accident management must be adapted to give greater autonomy to local participants in the reconstruction of satisfactory living conditions. (authors)

Application of the accident management information needs methodology to a severe accident sequence

International Nuclear Information System (INIS)

Ward, L.W.; Hanson, D.J.; Nelson, W.R.; Solberg, D.E.

1989-01-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel

Application of the accident management information needs methodology to a severe accident sequence

Energy Technology Data Exchange (ETDEWEB)

Ward, L.W.; Hanson, D.J.; Nelson, W.R. (Idaho National Engineering Laboratory, Idaho Falls (USA)); Solberg, D.E. (Nuclear Regulatory Commission, Washington, DC (USA))

1989-11-01

The U.S. Nuclear Regulatory Commission is conducting an accident management research program that emphasizes the use of severe accident research to enhance the ability of plant operating personnel to effectively manage severe accidents. Hence, it is necessary to ensure that the plant instrumentation and information systems adequately provide this information to the operating staff during accident conditions. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed. The methodology identifies (a) the information needs of the plant personnel during a wide range of accident conditions, (b) the existing plant measurements capable of supplying these information needs and minor additions to instrument and display systems that would enhance management capabilities, (c) measurement capabilities and limitations during severe accident conditions, and (d) areas in which the information systems could mislead plant personnel.

The modeling of fuel rod behaviour under RIA conditions in the code DYN3D

International Nuclear Information System (INIS)

Rohde, U.

2001-01-01

A description of the fuel rod behaviour and heat transfer model used in the code DYN3D for nuclear reactor core dynamic simulations is given. Besides the solution of heat conduction equations in fuel and cladding, the model comprises a detailed description of heat transfer in the gas gap by conduction, radiation and fuel-cladding contact. The gas gap behaviour is modeled in a mechanistic way taking into account transient changes of the gas gap parameters based on given conditions for the initial state. Thermal, elastic and plastic deformations of fuel and cladding are taken into account within 1D approximation. A creeping law for time-dependent estimation of plastic deformations is implemented. Metal-water reaction of the cladding material in the high temperature region is considered. The cladding-coolant heat transfer regime map covers the region from one-phase liquid convection to dispersed flow with superheated steam. Special emphasis is put on taking into account the impact of thermodynamic non-equilibrium conditions on heat transfer. For the validation of the model, experiments on fuel rod behaviour during RIAs carried out in Russian and Japanese pulsed research reactors with shortened probes of fresh fuel rods are calculated. Comparisons between calculated and measured results are shown and discussed. It is shown, that the fuel rod behaviour is significantly influenced by plastic deformation of the cladding, post crisis heat transfer with sub-cooled liquid conditions and heat release from the metal-water reaction. Numerical studies concerning the fuel rod behaviour under RIA conditions in power reactors are reported on. It is demonstrated, that the fuel rod behaviour at high pressures and flow rates in power reactors is different from the behaviour under atmospheric pressure and stagnant flow conditions in the experiments. The mechanisms of fuel rod failure for fresh and burned fuel reported from the literature can be qualitatively reproduced by the DYN3D

Coupled fuel performance and thermal-hydraulics simulation with BISON and RELAP-7 at accident conditions

Energy Technology Data Exchange (ETDEWEB)

Martineau, R.C., E-mail: Richard.Martineau@inl.gov [Idaho National Laboratory, Idaho Falls, ID (United States)

2015-07-01

reactivity insertion accidents (RIA). (author)

Cobalt irradiation box ejection accident of ETRR-2

International Nuclear Information System (INIS)

El-Messiry, A.M.

2000-01-01

The new Egyptian test and research reactor number 2 ETRR-2, MTR type, is now under operational tests. It has a main central irradiation channel for the purpose of Co 60 isotope production with an intended rated capacity of 50000 Ci per year. The reactivity introduced in the reactor due to accidental ejection of the Co 60 irradiation box (CIB) should be discussed. This reactivity insertion accident (RIA) may be fast or slow with maximum reactivity worth 2.9428 $. The CIB may move with constant speed or variable acceleration according to its initial speed and the applied forces. This results in a linear, parabolic or sinusoidal motion, which in turn affects the reactivity insertion rate (RIR). The present work analyzes this type of perturbation during normal operating conditions: 22 MW full power and 1900 kg s -1 forced core cooling flow. The work serves as a part of the safety evaluation process applicable to similar MTR cores. The RIA code TRANSP20 is developed for this study. It simulates various types of RIR, fast or slow resulting from different CIB ejections. Scram signal due to power, period, inlet and outlet temperatures, or temperature difference is expected to activate the shutdown system. The work presents five case studies, two for fast ejection and three for slow. The transient behavior of the reactor during this is illustrated. The results show that the reactor can withstand slow ejection if the scram is available. However, for fast ejection the scram system does not prevent the clad temperature from exceeding safety limits. Recommendations to prevent or mitigate this accident are highlighted. (orig.)

Assessment of potential doses to workers during postulated accident conditions at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Hoover, M.D.; Newton, G.J.; Farrell, R.F.

1996-01-01

This qualitative hazard evaluation systematically assessed potential doses to workers during postulated accident conditions at the U.S. Department of Energy's Waste Isolation Pilot Plant (WIPP). Postulated accidents included the spontaneous ignition of a waste drum, puncture of a waste drum by a forklift, dropping of a waste drum from a forklift, and simultaneous dropping of seven drums during a crane failure. The descriptions and estimated frequencies of occurrence for these accidents were developed by the Hazard and Operability Study for CH TRU Waste Handling System (WCAP 14312). The estimated materials at risk, damage ratios, airborne release fractions and respirable fractions for these accidents were taken from the 1995 Safety Analysis Report (SAR) update and from the DOE handbook Airborne Release Fractions/Rates and Respirable Fractions for Nonreactor Nuclear Facilities (DOE-HDBK-3010-94). A Monte Carlo simulation was used to estimate the range of worker exposures that could result from each accident. Guidelines for evaluating the adequacy of defense-in-depth for worker protection at WIPP were adopted from a scheme presented by the International Commission on Radiological Protection in its publication on Protection from Potential Exposure: A Conceptual Framework (ICRP Publication 64). Probabilities of exposures greater than 5, 50, and 300 rem were less than 10 -2 , 10 -4 , and 10 -6 per year, respectively. In conformance with the guidance of DOE standard 3009-94, Appendix A (draft), we emphasize that use of these evaluation guidelines is not intended to imply that these numbers constitute acceptable limits for worker exposure under accident conditions. However, in conjunction with the extensive safety assessment in the 1995 SAR update, these results indicate that the Carlsbad Area Office strategy for the assessment of hazards and accidents assures the protection of workers, as well as members of the public and the environment

Predicting the impact of chronic health conditions on workplace productivity and accidents: results from two US Department of Energy national laboratories.

Science.gov (United States)

Frey, Jodi Jacobson; Osteen, Philip J; Berglund, Patricia A; Jinnett, Kimberly; Ko, Jungyai

2015-04-01

Examine associations of chronic health conditions on workplace productivity and accidents among US Department of Energy employees. The Health and Work Performance Questionnaire-Select was administered to a random sample of two Department of Energy national laboratory employees (46% response rate; N = 1854). The majority (87.4%) reported having one or more chronic health conditions, with 43.4% reporting four or more conditions. A population-attributable risk proportions analysis suggests improvements of 4.5% in absenteeism, 5.1% in presenteeism, 8.9% in productivity, and 77% of accidents by reducing the number of conditions by one level. Depression was the only health condition associated with all four outcomes. Results suggest that chronic conditions in this workforce are prevalent and costly. Efforts to prevent or reduce condition comorbidity among employees with multiple conditions can significantly reduce costs and workplace accident rates.

RIA type tests in ACPR

International Nuclear Information System (INIS)

Preda, Marin; Stefan, Violeta; Ancuta, Mirela; Negut, Gheorghe

2008-01-01

For a better NPP operation fuel behavior in accidental conditions (LOCA) is of great interest. Irradiation tests in ACPR can give interesting data on the CANDU fuel behavior in such kind of accidents. These data can be used for simulation, calibration and validation of fuel computer codes. The tests were accomplished in the TRIGA Annular Core Pulse Reactor (ACPR). Reactivity insertion accidents are not specific for the CANDU reactors but this type of test can contribute to a better understanding of CANDU type fuel behavior during various conditions.The tests were accomplished in the ambient pressure and temperature with fresh fuel probes. These tests gave similar results on the clad-fuel, and clad-coolant interactions which occur in LOCA accidents. The tests will be continued with instrumentation improvements what will give better statistics and information on fuel behavior in accident conditions. The structure of the paper is the following: - 1. Introduction; - 2. Irradiation device description; - 2.1. Capsule main parameters; - 2.1.1. Initial conditions; - 2.1.2. Test conditions; - 3. Tests objectives; - 4. Test of fuel; - 5. Results; - 5.1. Temperature effects; - 5.2. Pressure effects; - 6. Conclusion

Estimate of radionuclide release characteristics into containment under severe accident conditions

International Nuclear Information System (INIS)

Nourbakhsh, H.P.

1993-11-01

A detailed review of the available light water reactor source term information is presented as a technical basis for development of updated source terms into the containment under severe accident conditions. Simplified estimates of radionuclide release and transport characteristics are specified for each unique combination of the reactor coolant and containment system combinations. A quantitative uncertainty analysis in the release to the containment using NUREG-1150 methodology is also presented

Support mechanisms for oil spill accident response in costal lagoon areas (Ria de Aveiro, Portugal)

Science.gov (United States)

Oliveira, Eduardo R.; Silveira, Bruno; Alves, Fátima L.

2014-10-01

Oil spill accidents can be caused by several risk factors associated to maritime transport and port activities, which cannot always be predicted or controlled. Therefore, it is essential to support prevention and contingency plans, whose effectiveness is crucial to produce adequate responses and minimize resulting impacts. Ria de Aveiro (Portugal) is a wide coastal lagoon, within a densely populated area, representing a concentration of important biodiversity resources and several economic activities. This paper presents alternative methodologies to support the optimization of civil protection assets in the occurrence of oil spill events and the results of their application on a section area of the Aveiro Lagoon, using an established geographic information system database containing crucial data. The presented methodologies are based on the Environmental Sensitivity Index developed by the North American National Oceanic and Atmospheric Administration (USA) and the Global Vulnerability Index which were applied on the Bay of Biscay (Spain). However, during the development of this work, neither of these methodologies was considered to entirely assess the study area in its full extent, which led to the need to adapt and define a bespoke approach. The introduced changes include extra categories in shoreline classification, an adapted physical vulnerability index for coastal lagoons, differentiated aspects for highly protected status areas, qualitative assessment of socioeconomic features and an access and operability index created to support emergency operation response. The resulting maps are the subject of analysis, in which considerations regarding control and cleanup methods are introduced, together with guidelines for further integration in local risk management strategies.

Analysis of effects of calandria tube uncovery under severe accident conditions in CANDU reactors

International Nuclear Information System (INIS)

Rogers, J.T.; Currie, T.C.; Atkinson, J.C.; Dick, R.

1983-01-01

A study is being undertaken for the Atomic Energy Control Board to assess the thermal and hydraulic behaviour of CANDU reactor cores under accident conditions more severe than those normally considered in the licensing process. In this paper, we consider the effects on a coolant channel of the uncovery of a calandria tube by moderator boil-off following a LOCA in a Bruce reactor unit in which emergency cooling is ineffective and the moderator heat sink is impaired by the failure of the moderator cooling system. Calandria tube uncovery and its immediate consequences, as described here, constitute only one part of the entire accident sequence. Other aspects of this sequence as well as results of the analysis of the other accident sequences studied will be described in the final report on the project and in later papers

Probability analysis of WWER-1000 fuel elements behavior under steady-state, transient and accident conditions of reactor operation

International Nuclear Information System (INIS)

Tutnov, A.; Alexeev, E.

2001-01-01

'PULSAR-2' and 'PULSAR+' codes make it possible to simulate thermo-mechanical and thermo-physical parameters of WWER fuel elements. The probabilistic approach is used instead of traditional deterministic one to carry out a sensitive study of fuel element behavior under steady-state operation mode. Fuel elements initial parameters are given as a density of the probability distributions. Calculations are provided for all possible combinations of initial data as fuel-cladding gap, fuel density and gas pressure. Dividing values of these parameters to intervals final variants for calculations are obtained . Intervals of permissible fuel-cladding gap size have been divided to 10 equal parts, fuel density and gas pressure - to 5 parts. Probability of each variant realization is determined by multiplying the probabilities of separate parameters, because the tolerances of these parameters are distributed independently. Simulation results are turn out in the probabilistic bar charts. The charts present probability distribution of the changes in fuel outer diameter, hoop stress kinetics and fuel temperature versus irradiation time. A normative safety factor is introduced for control of any criterion realization and for determination of a reserve to the criteria failure. A probabilistic analysis of fuel element behavior under Reactivity Initiating Accident (RIA) is also performed and probability fuel element depressurization under hypothetical RIA is presented

Should evacuation conditions after a nuclear accident be revised?

International Nuclear Information System (INIS)

Nifenecker, H.

2011-01-01

The author proposes to draw lessons from the Fukushima accident, notably in the field of post-accident management. He discusses the definition of an as widely understandable as possible method of description of risks related to irradiations after a nuclear accident. As these irradiations are mainly low dose ones which have a carcinogenic effect, he proposes to assess the average life expectancy loss due to an irradiation. Then, this risk can be easily compared with other risks like air pollution, smoking and passive smoking, and so on. Then, once this risk assessment method is well defined, it is possible to associate the inhabitants of contaminated areas to the post-accident management. They could then decide to go back to their homes or not with full knowledge of the facts

RIA tests in CABRI with MOX fuel

International Nuclear Information System (INIS)

Schmitz, F.; Papin, J.; Gonnier, C.

2000-01-01

Three MOX-fuel tests have been successfully performed within the framework of the CABRI REP-Na test program. From the experimental findings which are presently available, no evidence for thermal effects resulting from the heterogeneous nature of the fuel can be given. There are very clear hints however that fission gas effects are enhanced with regard to the behaviour of UO 2 . The clad rupture observed in REP-Na 7 is of different nature than the failures observed in Cabri tests with UO 2 fuel. Failures of UO 2 fuel rods only occurred when the clad mechanical properties were severely affected by the presence of hydride blisters, while in REP-Na 7 a clear indication is made that the loading potential of the MOX fuel pellets was high enough to break a sound cladding. Concerning the transient fuel behaviour after reaching the critical heat-flux under reactor typical conditions (pressure, temperature and flow), no data base could be provided by the tests in the present sodium test loop (as for the UO 2 fuel behaviour). The IPSN project to implement into the Cabri reactor a pressurised water loop which will allow to simulate the complete RIA accident sequence under PWR reactor typical conditions, aims at providing this missing data base. (author)

Guidance of reactor operators and TSC personnel with the severe accident management guidance under shutdown and low power conditions

International Nuclear Information System (INIS)

Van Haesendonck, M.F.; Prior, R.P.

2000-01-01

The Westinghouse Owners Group Severe Accident Management Guidance (WOG SAMG) was developed between 1991 and 1994. The primary goals for severe accident management that form the basis of the WOG SAMG are to terminate any radioactive releases to the environment; to prevent failure of any containment fission product boundary and to return the plant to a controlled stable condition. The WOG SAMG is primarily a TSC tool for mitigation of low probability core damage events. The philosophy is that control room operators should remain focused on the prevention of core damage, whereas the TSC personnel should concentrate on the mitigation of the severe accident. The symptom based package is built up as a structured process for choosing appropriate actions based on actual plant conditions. No detailed knowledge of severe accident phenomena is required. The scope of the WOG SAMG is limited to severe accidents resulting from initiating events occurring during full power operation. However, a number of studies such as the EdF EPS 1300 Probabilistic Safety Assessment (PSA), the shutdown Probabilistic Risk Assessment (PRA) for Surry, the BERA shutdown PRA for Beznau, the EPRI/ Westinghouse ORAM methodology etc. have shown that the frequency of core damage (a severe accident) during shutdown and low power operation can be of the same order of magnitude as for full power operation. The at-power SAMG is viewed as the resolution of the severe accident issue. Similarly, it is expected that as shutdown PRAs mature, the final resolution of the severe accident issue will lie in SAMG for low power and shutdown operation. Therefore in resolution of this issue, Westinghouse has developed the Shutdown Severe Accident Management Guidance (SSAMG) which gives guidance for both control room and TSC personnel to mitigate a severe accident under shutdown or low power conditions. In the last few years, many LWR plants have been implementing SAMG. In the US, all plants have developed SAMG, and many

BISON Modeling of Reactivity-Initiated Accident Experiments in a Static Environment

Energy Technology Data Exchange (ETDEWEB)

Folsom, Charles P.; Jensen, Colby B.; Williamson, Richard L.; Woolstenhulme, Nicolas E.; Ban, Heng; Wachs, Daniel M.

2016-09-01

In conjunction with the restart of the TREAT reactor and the design of test vehicles, modeling and simulation efforts are being used to model the response of Accident Tolerant Fuel (ATF) concepts under reactivity insertion accident (RIA) conditions. The purpose of this work is to model a baseline case of a 10 cm long UO2-Zircaloy fuel rodlet using BISON and RELAP5 over a range of energy depositions and with varying reactor power pulse widths. The results show the effect of varying the pulse width and energy deposition on both thermal and mechanical parameters that are important for predicting failure of the fuel rodlet. The combined BISON/RELAP5 model captures coupled thermal and mechanical effects on the fuel-to-cladding gap conductance, cladding-to-coolant heat transfer coefficient and water temperature and pressure that would not be capable in each code individually. These combined effects allow for a more accurate modeling of the thermal and mechanical response in the fuel rodlet and thermal-hydraulics of the test vehicle.

Analytical criteria for fuel failure modes observed in reactivity initiated accidents

International Nuclear Information System (INIS)

Luxat, J.C.

2005-01-01

The behaviour of nuclear fuel subjected to a short duration power pulse is of relevance to LWR and CANDU reactor safety. A Reactivity Initiated Accident (RIA) in an LWR would subject fuel to a short duration power pulse of large amplitude, whereas in CANDU a large break Loss of Coolant Accident (LOCA) would subject fuel to a longer duration, lower amplitude power excursion. The energy generated in the fuel during the power pulse is a key parameter governing the fuel response. This paper reviews the various power pulse tests that have been conducted in research reactors over the past three decades and summarizes the fuel failure modes that that have been observed in these tests. A simple analytical model is developed to characterize fuel behaviour under power pulse conditions and the model is applied to assess the experimental data from the power pulse tests. It is shown that the simple model provides a good basis for establishing criteria that demarcate the observed fuel failure modes for the various fuel designs that have been used in these tests. (author)

Thermal hydraulic analysis of aggressive secondary cooldown in small break loss of coolant accident with total loss of high pressure safety injection

International Nuclear Information System (INIS)

Han, S. J.; Im, H. K.; Yang, J. U.

2003-01-01

Recently, Probabilistic Safety Assessment (PSA) has being applied to various fields as a basic technique of Risk-Informed Applications (RIA). To use RIA, the present study focuses on the detailed thermal hydraulic analyses for major accident sequences and success criteria to support a development of PSA model for Korea Standard Nuclear Power plant (KSNP). The primary purpose of the present study is to evaluate the success criteria of Aggressive Secondary Cooldown (ASC) in Small Break Loss Of Coolant Accident (SBLOCA) with total loss of High Pressure Safety Injection (HPSI) and to enhance the understanding of related thermal hydraulic behavior and phenomena. The accident scenario was 2 inch coldleg break LOCA without HPSI, with 1/2 Low Pressure Safety Injection (LPSI), and performing ASC limited by 55.6 .deg. C /hr (100 .deg. F/hr) cooldown rate at 15 minute after reactor trip, which successively reaches the LPSI condition for about 1.5hr after starting ASC operation with the Peak Cladding Temperature (PCT) of the hottest rod below the core damage criteria 1204.4 .deg. C (2200 .deg. F). In the present study, more relaxed success criteria than the previous PSA for KSNP could be generated under an assumption that operator should maintain the adequate ASC operation. However, it is necessary to evaluate uncertainties arisen from the related parameters of the ASC operation

Comparison of US/FRG accident condition models for HTGR fuel failure and radionuclide release

International Nuclear Information System (INIS)

Verfondern, K.

1991-03-01

The objective was to compare calculation models used in safety analyses in the US and FRG which describe fission product release behavior from TRISO coated fuel particles under core heatup accident conditions. The frist step performed is the qualitative comparison of both sides' fuel failure and release models in order to identify differences and similarities in modeling assumptions and inputs. Assumptions of possible particle failure mechanisms under accident conditions (SiC degradation, pressure vessel) are principally the same on both sides though they are used in different modeling approaches. The characterization of a standard (= intact) coated particle to be of non-releasing (GA) or possibly releasing (KFA/ISF) type is one of the major qualitative differences. Similar models are used regarding radionuclide release from exposed particle kernels. In a second step, a quantitative comparison of the calculation models was made by assessing a benchmark problem predicting particle failure and radionuclide release under MHTGR conduction cooldown accident conditions. Calculations with each side's reference method have come to almost the same failure fractions after 250 hours for the core region with maximum core heatup temperature despite the different modeling approaches of SORS and PANAMA-I. The comparison of the results of particle failure obtained with the Integrated Failure and Release Model for Standard Particles and its revision provides a 'verification' of these models in this sense that the codes (SORS and PANAMA-II, and -III, respectively) which were independently developed lead to very good agreement in the predictions. (orig./HP) [de

Key Characteristics of Combined Accident including TLOFW accident for PSA Modeling

Energy Technology Data Exchange (ETDEWEB)

Kim, Bo Gyung; Kang, Hyun Gook [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [Khalifa University of Science, Technology and Research, Abu Dhabi (United Arab Emirates)

2015-05-15

The conventional PSA techniques cannot adequately evaluate all events. The conventional PSA models usually focus on single internal events such as DBAs, the external hazards such as fire, seismic. However, the Fukushima accident of Japan in 2011 reveals that very rare event is necessary to be considered in the PSA model to prevent the radioactive release to environment caused by poor treatment based on lack of the information, and to improve the emergency operation procedure. Especially, the results from PSA can be used to decision making for regulators. Moreover, designers can consider the weakness of plant safety based on the quantified results and understand accident sequence based on human actions and system availability. This study is for PSA modeling of combined accidents including total loss of feedwater (TLOFW) accident. The TLOFW accident is a representative accident involving the failure of cooling through secondary side. If the amount of heat transfer is not enough due to the failure of secondary side, the heat will be accumulated to the primary side by continuous core decay heat. Transients with loss of feedwater include total loss of feedwater accident, loss of condenser vacuum accident, and closure of all MSIVs. When residual heat removal by the secondary side is terminated, the safety injection into the RCS with direct primary depressurization would provide alternative heat removal. This operation is called feed and bleed (F and B) operation. Combined accidents including TLOFW accident are very rare event and partially considered in conventional PSA model. Since the necessity of F and B operation is related to plant conditions, the PSA modeling for combined accidents including TLOFW accident is necessary to identify the design and operational vulnerabilities.The PSA is significant to assess the risk of NPPs, and to identify the design and operational vulnerabilities. Even though the combined accident is very rare event, the consequence of combined

Potential for containment leak paths through electrical penetration assemblies under severe accident conditions. [PWR; BWR

Energy Technology Data Exchange (ETDEWEB)

Sebrell, W.

1983-07-01

The leakage behavior of containments beyond design conditions and knowledge of failure modes is required for evaluation of mitigation strategies for severe accidents, risk studies, emergency preparedness planning, and siting. These studies are directed towards assessing the risk and consequences of severe accidents. An accident sequence analysis conducted on a Boiling Water Reactor (BWR), Mark I (MK I), indicated very high temperatures in the dry-well region, which is the location of the majority of electrical penetration assemblies. Because of the high temperatures, it was postulated in the ORNL study that the sealants would fail and all the electrical penetration assemblies would leak before structural failure would occur. Since other containments had similar electrical penetration assemblies, it was concluded that all containments would experience the same type of failure. The results of this study, however, show that this conclusion does not hold for PWRs because in the worst accident sequence, the long time containment gases stabilize to 350/sup 0/F. BWRs, on the other hand, do experience high dry-well temperatures and have a higher potential for leakage.

Overview of core disruptive accidents

International Nuclear Information System (INIS)

Marchaterre, J.F.

1977-01-01

An overview of the analysis of core-disruptive accidents is given. These analyses are for the purpose of understanding and predicting fast reactor behavior in severe low probability accident conditions, to establish the consequences of such conditions and to provide a basis for evaluating consequence limiting design features. The methods are used to analyze core-disruptive accidents from initiating event to complete core disruption, the effects of the accident on reactor structures and the resulting radiological consequences are described

MDEP Common Position CP-EPRWG-04. Common position on EPR containment heat removal system in accident conditions

International Nuclear Information System (INIS)

2015-01-01

The importance of the integrity of the containment as a fundamental barrier to protect the people and environment against the effects of a nuclear accident is well established. In this regard, an essential objective is that the necessity for off-site counter-measures to reduce radiological consequences be limited or even eliminated. The design should provide engineering means to address those sequences which would otherwise lead to large or early releases, even in case of severe external hazards. The plant shall be designed so that it can be brought into a controlled and stable state and the containment function can be maintained, under accident conditions in which there is a significant amount of radioactive material in the containment, i.e. resulting from severe degradation of the reactor core. It is expected that due consideration to these requirements is to be given while tailoring long term loss of electrical power mitigation strategies. In order to reliably maintain the containment barrier, the regulators believe that: - safety features specifically designed for fulfilling safety functions required in core melt accidents shall be independent to the extent reasonably practicable from the Systems, Structures and Components (SSC) of the other levels of defense; - safety features specifically designed for fulfilling safety functions required in core melt accidents shall be safety classified and adequately qualified for the core melt accident environmental conditions for the time frame for which they are required to operate. In the light of the Fukushima Daiichi accident, the regulators believe that those safety features shall be designed with an adequate margin as compared to the levels of natural hazards considered for the site hazard evaluation; - the systems and components necessary for ensuring the containment function in a core melt accident shall have reliability commensurate with the function that they are required to fulfil. This may require redundancy of

The influence of simultaneous or sequential test conditions in the properties of industrial polymers, submitted to PWR accident simulations

International Nuclear Information System (INIS)

Carlin, F.; Alba, C.; Chenion, J.; Gaussens, G.; Henry, J.Y.

1986-10-01

The effect of PWR plant normal and accident operating conditions on polymers forms the basis of nuclear qualification of safety-related containment equipment. This study was carried out on the request of safety organizations. Its purpose was to check whether accident simulations carried out sequentially during equipment qualification tests would lead to the same deterioration as that caused by an accident involving simultaneous irradiation and thermodynamic effects. The IPSN, DAS and the United States NRC have collaborated in preparing this study. The work carried out by ORIS Company as well as the results obtained from measurement of the mechanical properties of 8 industrial polymers are described in this report. The results are given in the conclusion. They tend to show that, overall, the most suitable test cycle for simulating accident operating conditions would be one which included irradiation and consecutive thermodynamic shock. The results of this study and the results obtained in a previous study, which included the same test cycles, except for more severe thermo-ageing, have been compared. This comparison, which was made on three elastomers, shows that ageing after the accident has a different effect on each material [fr

Tratamento cirúrgico da artéria coronária direita intra-atrial

Directory of Open Access Journals (Sweden)

José Carlos R. IGLÉZIAS

1997-07-01

Full Text Available A localização intracavitária da artéria coronária é rara. Segundo Ochsner & Mills (1, ela ocorreu com a artéria coronária direita em 0,9% e com o ramo interventricular em 0,2%. A localização da lesão e as condições patológicas relacionadas ao comprimento e diâmetro da coronária podem auxiliar na exposição da coronária intracavitária para uma revascularização apropriada. Freqüentemente os cirurgiões não estão habituados com a posição intracavitária e, durante a dissecção, podem abrir uma câmara cardíaca onde o vaso penetra. Os problemas que podem advir dai são a entrada de ar para a cavidade, a dificuldade na exposição do vaso, o sangramento e a obstrução da artéria durante o fechamento da miotomia. São relatados os casos de 3 pacientes que necessitaram de revascularização cirúrgica do miocárdio e que apresentavam a artéria coronária direita intracavitária. A localização e o comprimento da porção intracavitária da artéria auxiliam no manejo intra-operatório. A técnica utilizada para o fechamento da cavidade variou entre a anastomose na posição intracavitária com o fechamento da miotomia ao redor do enxerto (Figura 1, a liberação da artéria coronária para uma posição superficial (Figura 2, seguida da anastomose e fechamento da cavidade com sutura simples, feita subepicárdica.An intracavitary location of a coronary artery is rare in our surgical experience with revascularization. This variant has occured in the right coronary artery (0.01% and in left anterior descending coronary artery (0.2%. The location of the lesion and the pathological condition, length and size of the coronary may dictate exposure of an intracavitary coronary artery for proper revascularization; more commonly surgeons are anaware of the intracavitary position and during intramyocardial dissection of an artery will open a cardiac chamber where the vessel traverses the cavity. Problems that arise are introducion

Professional experience and traffic accidents/near-miss accidents among truck drivers.

Science.gov (United States)

Girotto, Edmarlon; Andrade, Selma Maffei de; González, Alberto Durán; Mesas, Arthur Eumann

2016-10-01

To investigate the relationship between the time working as a truck driver and the report of involvement in traffic accidents or near-miss accidents. A cross-sectional study was performed with truck drivers transporting products from the Brazilian grain harvest to the Port of Paranaguá, Paraná, Brazil. The drivers were interviewed regarding sociodemographic characteristics, working conditions, behavior in traffic and involvement in accidents or near-miss accidents in the previous 12 months. Subsequently, the participants answered a self-applied questionnaire on substance use. The time of professional experience as drivers was categorized in tertiles. Statistical analyses were performed through the construction of models adjusted by multinomial regression to assess the relationship between the length of experience as a truck driver and the involvement in accidents or near-miss accidents. This study included 665 male drivers with an average age of 42.2 (±11.1) years. Among them, 7.2% and 41.7% of the drivers reported involvement in accidents and near-miss accidents, respectively. In fully adjusted analysis, the 3rd tertile of professional experience (>22years) was shown to be inversely associated with involvement in accidents (odds ratio [OR] 0.29; 95% confidence interval [CI] 0.16-0.52) and near-miss accidents (OR 0.17; 95% CI 0.05-0.53). The 2nd tertile of professional experience (11-22 years) was inversely associated with involvement in accidents (OR 0.63; 95% CI 0.40-0.98). An evident relationship was observed between longer professional experience and a reduction in reporting involvement in accidents and near-miss accidents, regardless of age, substance use, working conditions and behavior in traffic. Copyright © 2016 Elsevier Ltd. All rights reserved.

Analysis of flammability in the attached buildings to containment under severe accident conditions

Energy Technology Data Exchange (ETDEWEB)

Rosa, J.C. de la, E-mail: juan-carlos.de-la-rosa-blul@ec.europa.eu [European Commission Joint Research Centre (Netherlands); Fornós, Joan, E-mail: jfornosh@anacnv.com [Asociación Nuclear Ascó-Vandellós (Spain)

2016-11-15

Highlights: • Analysis of flammability conditions in buildings outside containment. • Stepwise approach easily applicable for any kind of containment and attached buildings layout. • Detailed application for real plant conditions has been included. - Abstract: Right after the events unfolded in Fukushima Daiichi, the European Union countries agreed in subjecting Nuclear Power Plants to Stress Tests as developed by WENRA and ENSREG organizations. One of the results as implemented in many European countries derived from such tests consisted of mandatory technical instructions issued by nuclear regulatory bodies on the analysis of potential risk of flammable gases in attached buildings to containment. The current study addresses the key aspects of the analysis of flammable gases leaking to auxiliary buildings attached to Westinghouse large-dry PWR containment for the specific situation where mitigating systems to prevent flammable gases to grow up inside containment are available, and containment integrity is preserved – hence avoiding isolation system failure. It also provides a full practical exercise where lessons learned derived from the current study – hence limited to the imposed boundary conditions – are applied. The leakage of gas from the containment to the support buildings is based on separate calculations using the EPRI-owned Modular Accident Analysis Program, MAAP4.07. The FATE™ code (facility Flow, Aerosol, Thermal, and Explosion) was used to model the transport and distribution of leaked flammable gas (H{sub 2} and CO) in the penetration buildings. FATE models the significant mixing (dilution) which occurs as the released buoyant gas rises and entrains air. Also, FATE accounts for the condensation of steam on room surfaces, an effect which acts to concentrate flammable gas. The results of the analysis show that during a severe accident, flammable conditions are unlikely to occur in compartmentalized buildings such as the one used in the

Analysis of flammability in the attached buildings to containment under severe accident conditions

International Nuclear Information System (INIS)

Rosa, J.C. de la; Fornós, Joan

2016-01-01

Highlights: • Analysis of flammability conditions in buildings outside containment. • Stepwise approach easily applicable for any kind of containment and attached buildings layout. • Detailed application for real plant conditions has been included. - Abstract: Right after the events unfolded in Fukushima Daiichi, the European Union countries agreed in subjecting Nuclear Power Plants to Stress Tests as developed by WENRA and ENSREG organizations. One of the results as implemented in many European countries derived from such tests consisted of mandatory technical instructions issued by nuclear regulatory bodies on the analysis of potential risk of flammable gases in attached buildings to containment. The current study addresses the key aspects of the analysis of flammable gases leaking to auxiliary buildings attached to Westinghouse large-dry PWR containment for the specific situation where mitigating systems to prevent flammable gases to grow up inside containment are available, and containment integrity is preserved – hence avoiding isolation system failure. It also provides a full practical exercise where lessons learned derived from the current study – hence limited to the imposed boundary conditions – are applied. The leakage of gas from the containment to the support buildings is based on separate calculations using the EPRI-owned Modular Accident Analysis Program, MAAP4.07. The FATE™ code (facility Flow, Aerosol, Thermal, and Explosion) was used to model the transport and distribution of leaked flammable gas (H_2 and CO) in the penetration buildings. FATE models the significant mixing (dilution) which occurs as the released buoyant gas rises and entrains air. Also, FATE accounts for the condensation of steam on room surfaces, an effect which acts to concentrate flammable gas. The results of the analysis show that during a severe accident, flammable conditions are unlikely to occur in compartmentalized buildings such as the one used in the

Development of instrumentation systems for severe accidents. 4. New accident tolerant in-containment pressure transducer for containment pressure monitoring system

International Nuclear Information System (INIS)

Oba, Masato; Teruya, Kuniyuki; Yoshitsugu, Makoto; Ikeuchi, Takeshi

2015-01-01

The accident at Tokyo Electric Power Company's Fukushima Dai-ichi Nuclear Power Plant (TF-1 accident) caused severe situations and resulted in a difficulty in measuring important parameters for monitoring plant conditions. Therefore, we have studied the TF-1 accident to select the important parameters that should be monitored at the severe accident and are developing the Severe Accident Instrumentations and Monitoring Systems that could measure the parameters in severe accident conditions. Mitsubishi Heavy Industries, LTD (MHI) developed a new accident tolerant containment pressure monitoring system and demonstrated that the monitoring system could endure extremely harsh environmental conditions that envelop severe accident environmental conditions inside a containment such as maximum operating temperature of up to 300degC and total integrated dose (TID) of 1 MGy gamma. The new containment pressure monitoring system comprises of a strain gage type pressure transducer and a mineral insulated (MI) cable with ceramic connectors, which are located in the containment, and a strain measuring amplifier located outside the containment. Less thermal and radiation degradation is achieved because of minimizing use of organic materials for in-containment equipment such as the transducer and connectors. Several tests were performed to demonstrate the performance and capability of the in-containment equipment under severe accident environmental conditions and the major steps in this testing were run in the following test sequences: (1) the baseline functional tests (e.g., repeatability, non-linearity, hysteresis, and so on) under normal conditions, (2) accident radiation testing, (3) seismic testing, and (4) steam/temperature test exposed to simulated severe accident environmental conditions. The test results demonstrate that the new pressure transducer can endure the simulated severe accident conditions. (author)

Review of U.S. Army Aviation Accident Reports: Prevalence of Environmental Stressors and Medical Conditions

Science.gov (United States)

2017-10-18

terminology related to an aforementioned stressor or medical condition. Table 1 presents the identified operational stressor with the keywords extracted...USAARL Report No. 2018-02 Review of U.S. Army Aviation Accident Reports: Prevalence of Environmental Stressors and Medical Conditions By Kathryn...Environmental Stressors and Medical Conditions N/A N/A N/A N/A N/A N/A Feltman, Kathryn A. Kelley, Amanda M. Curry, Ian P. Boudreaux, David A. Milam

Shipping container response to severe highway and railway accident conditions: Appendices

International Nuclear Information System (INIS)

Fischer, L.E.; Chou, C.K.; Gerhard, M.A.; Kimura, C.Y.; Martin, R.W.; Mensing, R.W.; Mount, M.E.; Witte, M.C.

1987-02-01

Volume 2 contains the following appendices: Severe accident data; truck accident data; railroad accident data; highway survey data and bridge column properties; structural analysis; thermal analysis; probability estimation techniques; and benchmarking for computer codes used in impact analysis. (LN)

Ruthenium transport experiments in air ingress accident conditions

Energy Technology Data Exchange (ETDEWEB)

Teemu, Karkele; Ulrika, Backman; Ari, Auvinen; Unto, Tapper; Jorma, Jokiniemi [VTT Technical Research Centre of Finland, Fine Particles (Finland); Riitta, Zilliacus; Maija, Lipponen; Tommi, Kekki [VTT Technical Research Centre of Finland, Accident Management (Finland); Jorma, Jokiniemi [Kuopio Univ., Dept. of Environmental Sciences, Fine Particle and Aerosol Technology Lab. (Finland)

2007-07-01

In this study the release, transport and speciation of ruthenium in conditions simulating an air ingress accident was studied. Ruthenium dioxide was exposed to oxidising environment at high temperature (1100-1700 K) in a tubular flow furnace. At these conditions volatile ruthenium species were formed. A large fraction of the released ruthenium was deposited in the tube as RuO{sub 2}. Depending on the experimental conditions 1-26 wt% of the released ruthenium was trapped in the outlet filter as RuO{sub 2} particles. In stainless steel tube 0-8.8 wt% of the released ruthenium reached the trapping bottle as gaseous RuO{sub 4}. A few experiments were carried out, in which revaporization of ruthenium deposited on the tube walls was studied. In these experiments, oxidation of RuO{sub 2} took place at a lower temperature. During revaporization experiments 35-65 % of ruthenium was transported as gaseous RuO{sub 4}. In order to close mass balance and achieve better time resolution 4 experiments were carried out using a radioactive tracer. In these experiments ruthenium profiles were measured. These experiments showed that the most important retention mechanism was decomposition of gaseous RuO{sub 3} into RuO{sub 2} as the temperature of the furnace was decreasing. In these experiments the transport rate of gaseous ruthenium was decreasing while the release rate was constant.

RIA testing capability of the transient reactor test facility

International Nuclear Information System (INIS)

Crawford, D.C.; Swanson, R.W.

1999-01-01

The advent of high-burnup fuel implementation in LWRs has generated international interest in high-burnup LWR fuel performance. Recent testing under simulated RIA conditions has demonstrated that certain fuel designs fail at peak fuel enthalpy values that are below existing regulatory criteria. Because many of these tests were performed with non-prototypically aggressive test conditions (i.e., with power pulse widths less than 10 msec FWHM and with non-protoypic coolant configurations), the results (although very informative) do not indisputably identify failure thresholds and fuel behavior. The capability of the TREAT facility to perform simulated RIA tests with prototypic test conditions is currently being evaluated by ANL personnel. TREAT was designed to accommodate test loops and vehicles installed for in-pile transient testing. During 40 years of TREAT operation and fuel testing and evaluation, experimenters have been able to demonstrate and determine the transient behavior of several types of fuel under a variety of test conditions. This experience led to an evolution of test methodology and techniques which can be employed to assess RIA behavior of LWR fuel. A pressurized water loop that will accommodate RIA testing of LWR and CANDU-type fuel has completed conceptual design. Preliminary calculations of transient characteristics and energy deposition into test rods during hypothetical TREAT RIA tests indicate that with the installation of a pressurized water loop, the facility is quite capable of performing prototypic RIA testing. Typical test scenarios indicate that a simulated RIA with a 72 msec FWHM pulse width and energy deposition of 1200 kJ/kg (290 cal/gm) is possible. Further control system enhancements would expand the capability to pulse widths as narrow as 40 msec. (author)

Stress in accident and post-accident management at Chernobyl

International Nuclear Information System (INIS)

Girard, P.; Dubreuil, G.H.

1996-01-01

The effects of the Chernobyl nuclear accident on the psychology of the affected population have been much discussed. The psychological dimension has been advanced as a factor explaining the emergence, from 1990 onwards, of a post-accident crisis in the main CIS countries affected. This article presents the conclusions of a series of European studies, which focused on the consequences of the Chernobyl accident. These studies show that the psychological and social effects associated with the post-accident situation arise from the interdependency of a number of complex factors exerting a deleterious effect on the population. We shall first attempt to characterise the stress phenomena observed among the population affected by the accident. Secondly, we will be presenting an anlysis of the various factors that have contributed to the emerging psychological and social features of population reaction to the accident and in post-accident phases, while not neglecting the effects of the pre-accident situation on the target population. Thirdly, we shall devote some initial consideration to the conditions that might be conducive to better management of post-accident stress. In conclusion, we shall emphasise the need to restore confidence among the population generally. (Author)

Fission product release from HTGR fuel under core heatup accident conditions - HTR2008-58160

International Nuclear Information System (INIS)

Verfondern, K.; Nabielek, H.

2008-01-01

Various countries engaged in the development and fabrication of modern fuel for the High Temperature Gas-Cooled Reactor (HTGR) have initiated activities of modeling the fuel and fission product release behavior with the aim of predicting the fuel performance under operating and accidental conditions of future HTGRs. Within the IAEA directed Coordinated Research Project CRP6 on 'Advances in HTGR Fuel Technology Development' active since 2002, the 13 participating Member States have agreed upon benchmark studies on fuel performance during normal operation and under accident conditions. While the former has been completed in the meantime, the focus is now on the extension of the national code developments to become applicable to core heatup accident conditions. These activities are supported by the fact that core heatup simulation experiments have been resumed recently providing new, highly valuable data. Work on accident performance will be - similar to the normal operation benchmark - consisting of three essential parts comprising both code verification that establishes the correspondence of code work with the underlying physical, chemical and mathematical laws, and code validation that establishes reasonable agreement with the existing experimental data base, but including also predictive calculations for future heating tests and/or reactor concepts. The paper will describe the cases to be studied and the calculational results obtained with the German computer model FRESCO. Among the benchmark cases in consideration are tests which were most recently conducted in the new heating facility KUEFA. Therefore this study will also re-open the discussion and analysis of both the validity of diffusion models and the transport data of the principal fission product species in the HTGR fuel materials as essential input data for the codes. (authors)

Oxidation behavior of fuel cladding tube in spent fuel pool accident condition

International Nuclear Information System (INIS)

Nemoto, Yoshiyuki; Kaji, Yoshiyuki; Ogawa, Chihiro; Nakashima, Kazuo; Tojo, Masayuki

2017-01-01

In spent fuel pool (SFP) under loss-of-cooling or loss-of-coolant severe accident condition, the spent fuels will be exposed to air and heated by their own residual decay heat. Integrity of fuel cladding is crucial for SFP safety therefore study on cladding oxidation in air at high temperature is important. Zircaloy-2 (Zry2) and zircaloy-4 (Zry4) were applied for thermogravimetric analyses (TGA) in different temperatures in air at different flow rates to evaluate oxidation behavior. Oxidation rate increased with testing temperature. In a range of flow rate of air which is predictable in spent fuel lack during a hypothetical SFP accident, influence of flow rate was not clearly observed below 950degC for the Zry2, or below 1050degC for Zry4. In higher temperature, oxidation rate was higher in high rate condition, and this trend was seen clearer when temperature increased. Oxide layers were carefully examined after the TGA analyses and compared with mass gain data to investigate detail of oxidation process in air. It was revealed that the mass gain data in pre-breakaway regime reflects growth of dense oxide film on specimen surface, meanwhile in post-breakaway regime, it reflects growth of porous oxide layer beneath fracture of the dense oxide film. (author)

Study of labor accidents in the rural environment: analysis of processes and conditions of work

Directory of Open Access Journals (Sweden)

Thaís Alves Brito

2009-01-01

Full Text Available The modernization of agriculture, that broadenned the mechanization of farming and the agrotoxic use, potentially increased some risks of accidents. The agriculture workers and cattle raising are constantly exposed to several physical, chemical and biological agents, like machine, implements, handly tools, agrotoxics, ectoparaziticides, domestic animals and poisonous animals, which can to bring accidents. The aiming the importance of this working class to economic developing of country, this study was done to identify the working process and accidents that strike the rural population. This article is composed by a specialized literature review between September and December of 2007, which was made consultations to periodical and scientific articles selected through searches in the database of Scielo and Bireme. It was founded few studies related to rural workers, as well as the main articles had as setting of investigation the Southern and Southeastern, mainly in state of São Paulo and Rio Grande do Sul. In relation to work conditions was noticed a high degree of insalubrities which the workers are exposed, such as handly tools, poisonous animals, insecure attitudes because of lack of training and the no use of equipments of individual protection. There are a prevalence of accidents among men, occurring predominantly the typical accidents, the occupational disease and commute accidents. The relationships of work have been modified along the years, being the outsourcing outstanding point, however this work relationship causes legal losses to workers, which in most of the time get without social welfare right

RADIATION CONDITIONS IN KALUGA REGION 30 YEARS AFTER CHERNOBYL NPP ACCIDENT

Directory of Open Access Journals (Sweden)

A. G. Ashitko

2016-01-01

Full Text Available The article describes radiation conditions in the Kaluga region 30 years after the Chernobyl NPP accident. The Chernobyl NPP accident caused radioactive contamination of nine Kaluga region territories: Duminichsky, Zhizdrinsky, Kuibyshevsky, Kirovsky, Kozelsky, Ludinovsky, Meshchovsky, Ulyanovsky and Hvastovichsky districts. Radioactive fallout was the strongest in three southern districts: Zhizdrinsky, Ulyanovsky and Hvastovichsky, over there cesium-137 contamination density is from 1 to 15Ci/km. According to the Russian Federation Government Order in 2015 there are 300 settlements (S in the radioactive contamination zone, including 14 settlements with caesium-137 soil contamination density from 5 to 15 Ci/ km2 and 286 settlements with the contamination density ranging from 1 to 5 Ci/km2. In the first years after the Chernobyl NPP accident in Kaluga region territories, contaminated with caesium-137, there were introduced restrictive land usage, were carried out agrochemical activities (ploughing, mineral fertilizer dressing, there was toughened laboratory radiation control over the main doze-forming foodstuff. All these measures facilitated considerable decrease of caesium-137 content in local agricultural produce. Proceeding from the achieved result, in 2002 there took place the transition to more tough requirements SanPiN 2.3.2.1078-01. Analysis of investigated samples from Zhizdrinsky, Ulyanovsky and Hvastovichsky districts demonstrated that since 2005 meat samples didn’t exceed the standard values, same for milk samples since 2007. Till the present time, the use of wild-growing mushrooms, berries and wild animals meat involves radiation issues. It was demonstrated that average specific activity of caesium-137 in milk samples keeps decreasing year after year. Long after the Chernobyl NPP accident, the main products forming internal irradiation doses in population are the wild-growing mushrooms and berries. Population average annual

Simulations of the design basis accident at conditions of power increase and the o transient of MSIV at overpressure conditions of the Laguna Verde Power Station

International Nuclear Information System (INIS)

Araiza M, E.; Nunez C, A.

2001-01-01

This document presents the analysis of the simulation of the loss of coolant accident at uprate power conditions, that is 2027 MWt (105% of the current rated power of 1931MWt). This power was reached allowing an increase in the turbine steam flow rate without changing the steam dome pressure value at its rated conditions (1020 psiaJ. There are also presented the results of the simulation of the main steam isolation va/ve transient at overpressure conditions 1065 psia and 1067 MWt), for Laguna Verde Nuclear Power Station. Both simulations were performed with the best estimate computer code TRA C BF1. The results obtained in the loss of coolant accident show that the emergency core coolant systems can recover the water level in the core before fuel temperature increases excessively, and that the peak pressure reached in the drywell is always below its design pressure. Therefore it is concluded that the integrity of the containment is not challenged during a loss of coolant accident at uprate power conditions.The analysis of the main steam isolation valve transients at overpressure conditions, and the analysis of the particular cases of the failure of one to six safety relief valves to open, show that the vessel peak pressures are below the design pressure and have no significant effect on vessel integrity. (Author)

Relationships of working conditions, health problems and vehicle accidents in bus rapid transit (BRT) drivers.

Science.gov (United States)

Gómez-Ortiz, Viviola; Cendales, Boris; Useche, Sergio; Bocarejo, Juan P

2018-04-01

The aim of this study was to estimate accident risk rates and mental health of bus rapid transit (BRT) drivers based on psychosocial risk factors at work leading to increased stress and health problems. A cross-sectional research design utilized a self-report questionnaire completed by 524 BRT drivers. Some working conditions of BRT drivers (lack of social support from supervisors and perceived potential for risk) may partially explain Bogota's BRT drivers' involvement in road accidents. Drivers' mental health problems were associated with higher job strain, less support from co-workers, fewer rewards and greater signal conflict while driving. To prevent bus accidents, supervisory support may need to be increased. To prevent mental health problems, other interventions may be needed such as reducing demands, increasing job control, reducing amount of incoming information, simplifying current signals, making signals less contradictory, and revising rewards. © 2018 Wiley Periodicals, Inc.

Hydrogen-management in beyond design accident conditions in NPP Neckar 2

International Nuclear Information System (INIS)

Zaiss, W.

1999-01-01

Neckar 2 is a 1340 MWE 4-loop pressurized water reactor (PWR) of Siemens KONVOI type, located in the south of Germany. It was first connected to the grid in January 1989. Commercial operation started in April 1989. Task assignment: In Germany it was recommended by the Reactor Safety Commission (RSK) on December 17, 1997, to reequip passive autocatalytic recombiners for the controlling of the hydrogen problem. The removal of the hydrogen is an essential part which guarantees the integrity of the containment. The implementation of the recombiners is a further step for the decrease of the nuclear rest risk. The RSK confirmed, that the implementation of the passive autocatalytic recombiners is a safety measure for the controlled removal of the hydrogen in beyond design accident conditions. Assumption : Failure of the whole residual heat removal system (RHRS) and non sufficient effect of the systems which have been installed for beyond design accident conditions. Effect on the reactor coolant system (RCS): The reactor core will be damaged by non sufficient cooling with the output of hydrogen because all the specified emergency actions have failed. The overheating of the core is responsible for the production of hydrogen by the reaction of zirconium of the fuel-rod cladding with the water vapour. In case of nuclear superheating it would be possible that the reactor vessel would start smelting. The interacting between the core and the concrete, together with the armouring of the biological shield would also produce hydrogen. The hydrogen would escape together with the water vapour out of the leak and would spread out into the whole containment. Results : the number and the position of the different sized recombiners were determined on engineering judgement. the following 4 scenarios are representatively. The 4 scenarios were analyzed for in beyond design accident conditions with the MELCOR-Code: No. 1: Loss of main feedwater supply with primary feed and bleed. No. 2

Response Analysis on Electrical Pulses under Severe Nuclear Accident Temperature Conditions Using an Abnormal Signal Simulation Analysis Module

Directory of Open Access Journals (Sweden)

Kil-Mo Koo

2012-01-01

Full Text Available Unlike design basis accidents, some inherent uncertainties of the reliability of instrumentations are expected while subjected to harsh environments (e.g., high temperature and pressure, high humidity, and high radioactivity occurring in severe nuclear accident conditions. Even under such conditions, an electrical signal should be within its expected range so that some mitigating actions can be taken based on the signal in the control room. For example, an industrial process control standard requires that the normal signal level for pressure, flow, and resistance temperature detector sensors be in the range of 4~20 mA for most instruments. Whereas, in the case that an abnormal signal is expected from an instrument, such a signal should be refined through a signal validation process so that the refined signal could be available in the control room. For some abnormal signals expected under severe accident conditions, to date, diagnostics and response analysis have been evaluated with an equivalent circuit model of real instruments, which is regarded as the best method. The main objective of this paper is to introduce a program designed to implement a diagnostic and response analysis for equivalent circuit modeling. The program links signal analysis tool code to abnormal signal simulation engine code not only as a one body order system, but also as a part of functions of a PC-based ASSA (abnormal signal simulation analysis module developed to obtain a varying range of the R-C circuit elements in high temperature conditions. As a result, a special function for abnormal pulse signal patterns can be obtained through the program, which in turn makes it possible to analyze the abnormal output pulse signals through a response characteristic of a 4~20 mA circuit model and a range of the elements changing with temperature under an accident condition.

Evaluation of the leakage behavior of inflatable seals subject to severe accident conditions

International Nuclear Information System (INIS)

Parks, M.B.

1989-11-01

Sandia National Laboratories, under the sponsorship of the United States Nuclear Regulatory Commission, is currently developing test validated methods to predict the pressure capacity of light water reactor containment buildings when subjected to postulated severe accident conditions. These conditions are well beyond the design basis. Scale model tests of steel and reinforced concrete containments have been conducted as well as tests of typical containment penetrations. As a part of this effort, a series of tests was recently conducted to determine the leakage behavior of inflatable seals. These seals are used to prevent leakage around personnel and escape lock doors of some containments. The results of the inflatable seals tests are the subject of this report. Inflatable seals were tested at both room temperature and at elevated temperatures representative of postulated severe accident conditions. Both aged (radiation and thermal) and unaged seals were included in the test program. The internal seal pressure at the beginning of each test was varied to cover the range of seal pressures actually used in containments. For each seal pressure level, the external (containment) pressure was increased until significant leakage past the seals was observed. Parameters that were monitored and recorded during the tests were the internal seal pressure, chamber pressure, leakage past the seals, and temperature of the test chamber and fixture to which the seals were attached. 8 refs., 34 figs., 7 tabs

Analysis of the behaviour of the Kozloduy NPP Unit 3 under severe accident conditions

International Nuclear Information System (INIS)

Velev, V.; Saraeva, V.

2004-01-01

The objective of the analysis is to study the behaviour of the Kozloduy NPP Unit 3 under severe accident conditions. The analysis is performed using computer code MELCOR 1.8.4. This report includes a brief description of Unit 3 active core as well as description and comparison of the key events

Experimental data report for Test TS-2 reactivity initiated accident test in NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Sobajima, Makoto; Fujishiro, Toshio; Kobayashi, Shinsho; Yamahara, Takeshi; Sukegawa, Tomohide; Kikuchi, Teruo

1993-02-01

This report presents experimental data for Test TS-2 which was the second test in a series of Reactivity Initiated Accident (RIA) condition test using pre-irradiated BWR fuel rods, performed at the Nuclear Safety Research Reactor (NSRR) in February, 1990. Test fuel rod used in the Test TS-2 was a short sized BWR (7x7) type rod which was fabricated from a commercial rod irradiated at Tsuruga Unit 1 power reactor. The fuel had an initial enrichment of 2.79% and a burnup of 21.3Gwd/tU (bundle average). A pulse irradiation of the test fuel rod was performed under a cooling condition of stagnant water at atmospheric pressure and at ambient temperature which simulated a BWR's cold start-up RIA event. The energy deposition of the fuel rod in this test was evaluated to be 72±5cal/g·fuel (66±5cal/g·fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, transient behavior of the test rod during the pulse irradiation, and, results of pre and post pulse irradiation examinations are described in this report. (author)

Nuclear power plant accident simulations of gasket materials under simultaneous radiation plus thermal plus mechanical stress conditions

International Nuclear Information System (INIS)

Gillen, K.T.; Malone, G.M.

1997-07-01

In order to probe the response of silicone door gasket materials to a postulated severe accident in an Italian nuclear power plant, compression stress relaxation (CSR) and compression set (CS) measurements were conducted under combined radiation (approximately 6 kGy/h) and temperature (up to 230 degrees C) conditions. By making some reasonable initial assumptions, simplified constant temperature and dose rates were derived that should do a reasonable job of simulating the complex environments for worst-case severe events that combine overall aging plus accidents. Further simplification coupled with thermal-only experiments allowed us to derive thermal-only conditions that can be used to achieve CSR and CS responses similar to those expected from the combined environments that are more difficult to simulate. Although the thermal-only simulations should lead to sealing forces similar to those expected during a severe accident, modulus and density results indicate that significant differences in underlying chemistry are expected for the thermal-only and the combined environment simulations. 15 refs., 31 figs., 15 tabs

Should evacuation conditions after a nuclear accident be revised?; Faut-il revoir les conditions d'evacuation a la suite d'un accident nucleaire?

Energy Technology Data Exchange (ETDEWEB)

Nifenecker, H.

2011-07-01

The author proposes to draw lessons from the Fukushima accident, notably in the field of post-accident management. He discusses the definition of an as widely understandable as possible method of description of risks related to irradiations after a nuclear accident. As these irradiations are mainly low dose ones which have a carcinogenic effect, he proposes to assess the average life expectancy loss due to an irradiation. Then, this risk can be easily compared with other risks like air pollution, smoking and passive smoking, and so on. Then, once this risk assessment method is well defined, it is possible to associate the inhabitants of contaminated areas to the post-accident management. They could then decide to go back to their homes or not with full knowledge of the facts

The analysis of a condition of an accident rate on highways of Tajikistan

International Nuclear Information System (INIS)

Davlatshoev, R.A.; Tursunov, A.A.

2005-01-01

In this clause the results of the analysis of an accident rate on highways of Tajikistan, according to the official information State Automobile Inspection the Ministry of Internal affairs of Republic of Tajikistan, and research of safe movement of automobiles in mountain conditions are given. On the basis of the qualitative and quantitative analysis, the ways of safe movement on roads of Republic of Tajikistan are determined

Probabilistic Approach to Conditional Probability of Release of Hazardous Materials from Railroad Tank Cars during Accidents

Science.gov (United States)

2009-10-13

This paper describes a probabilistic approach to estimate the conditional probability of release of hazardous materials from railroad tank cars during train accidents. Monte Carlo methods are used in developing a probabilistic model to simulate head ...

A Study on the Operation Strategy for Combined Accident including TLOFW accident

International Nuclear Information System (INIS)

Kim, Bo Gyung; Kang, Gook Young; Yoon, Ho Joon

2014-01-01

It is difficult for operators to recognize the necessity of a feed-and-bleed (F-B) operation when the loss of coolant accident and failure of secondary side occur. An F-B operation directly cools down the reactor coolant system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. The plant is not always necessary the F-B operation when the secondary side is failed. It is not necessary to initiate an F-B operation in the case of a medium or large break because these cases correspond to low RCS pressure sequences when the secondary side is failed. If the break size is too small to sufficiently decrease the RCS pressure, the F-B operation is necessary. Therefore, in the case of a combined accident including a secondary cooling system failure, the provision of clear information will play a critical role in the operators' decision to initiate an F-B operation. This study focuses on the how we establish the operation strategy for combined accident including the failure of secondary side in consideration of plant and operating conditions. Previous studies have usually focused on accidents involving a TLOFW accident. The plant conditions to make the operators confused seriously are usually the combined accident because the ORP only focuses on a single accident and FRP is less familiar with operators. The relationship between CET and PCT under various plant conditions is important to decide the limitation of initiating the F-B operation to prevent core damage

Study of the linearity of CABRI experimental ionization chambers during RIA transients

Science.gov (United States)

Lecerf, J.; Garnier, Y.; Hudelot, JP.; Duc, B.; Pantera, L.

2018-01-01

CABRI is an experimental pulse reactor operated by CEA at the Cadarache research center and funded by the French Nuclear Safety and Radioprotection Institute (IRSN). For the purpose of the CABRI International Program (CIP), operated and managed by IRSN under an OECD/NEA framework it has been refurbished since 2003 to be able to provide experiments in prototypical PWR conditions (155 bar, 300 °C) in order to study the fuel behavior under Reactivity Initiated Accident (RIA) conditions. This paper first reminds the objectives of the power commissioning tests performed on the CABRI facility. The design and location of the neutron detectors monitoring the core power are also presented. Then it focuses on the different methodologies used to calibrate the detectors and check the consistency and co-linearity of the measurements. Finally, it presents the methods used to check the linearity of the neutron detectors up to the high power levels ( 20 GW) reached during power transients. Some results obtained during the power tests campaign are also presented.

Application of the accident management information needs methodology to a severe accident sequence

International Nuclear Information System (INIS)

Ward, L.W.; Hanson, D.J.; Nelson, W.R.; Solberg, D.E.

1989-01-01

The U.S. Nuclear Regulatory Commission (NRC) is conducting an Accident Management Research Program that emphasizes the application of severe accident research results to enhance the capability of plant operating personnel to effectively manage severe accidents. A methodology to identify and assess the information needs of the operating staff of a nuclear power plant during a severe accident has been developed as part of the research program designed to resolve this issue. The methodology identifies the information needs of the plant personnel during a wide range of accident conditions, the existing plant measurements capable of supplying these information needs and what, if any minor additions to instrument and display systems would enhance the capability to manage accidents, known limitations on the capability of these measurements to function properly under the conditions that will be present during a wide range of severe accidents, and areas in which the information systems could mislead plant personnel. This paper presents an application of this methodology to a severe accident sequence to demonstrate its use in identifying the information which is available for management of the event. The methodology has been applied to a severe accident sequence in a Pressurized Water Reactor with a large dry containment. An examination of the capability of the existing measurements was then performed to determine whether the information needs can be supplied

Assessment of WWER fuel condition in design basis accident

International Nuclear Information System (INIS)

Bibilashvili, Yu.; Sokolov, N.; Andreeva-Andrievskaya, L.; Vlasov, Yu.; Nechaeva, O.; Salatov, A.

1994-01-01

The fuel behaviour in design basis accidents is assessed by means of the verified code RAPTA-5. The code uses a set of high temperature physico-chemical properties of the fuel components as determined for commercially produced materials, fuel rod simulators and fuel rod bundles. The WWER fuel criteria available in Russia for design basis accidents do not generally differ from the similar criteria adopted for PWR's. 12 figs., 11 refs

Failure of fretted steam generator tubes under accident conditions

International Nuclear Information System (INIS)

Forrest, C.F.

1996-10-01

Tests were carried out with a bank of tubes in a water tunnel to determine the tolerance of flawed nuclear reactor steam generator tubes to accident conditions which would result in high cross-flow velocities. Fourteen specimen tubes were tested, each having one or two types of defect machined into the surface simulating fretting-wear type scars found in some operating steam generators. The tubes were tested at flow velocities sufficient to induce high fluid elastic-type vibrations. Seven of the tubes failed near the thinnest section of the defects during the one-hour tests, due to impacting and/or rubbing between the tube and the support. Strain gauges, displacement transducers, force gauges and an accelerometer were used on the target tube and/or the tube immediately downstream of it to measure their vibrational characteristics

Robot dispatching Scenario for Accident Condition Monitoring of NPP

International Nuclear Information System (INIS)

Kim, Jongseog

2013-01-01

In March of 2011, unanticipated big size of tsunami attacks Fukushima NPP, this accident results in explosion of containment building. Tokyo electric power of Japan couldn't dispatch a robot for monitoring of containment inside. USA Packbot robot used for desert war in Iraq was supplied to Fukushima NPP for monitoring of high radiation area. Packbot also couldn't reach deep inside of Fukushima NPP due to short length of power cable. Japanese robot 'Queens' also failed to complete a mission due to communication problem between robot and operator. I think major reason of these robot failures is absence of robot dispatching scenario. If there was a scenario and a rehearsal for monitoring during or after accident, these unanticipated obstacles could be overcome. Robot dispatching scenario studied for accident of nuclear power plant was described herein. Study on scenario of robot dispatching is performed. Flying robot is regarded as good choice for accident monitoring. Walking robot with arm equipped is good for emergency valve close. Short time work and shift work by several robots can be a solution for high radiation area. Thin and soft cable with rolling reel can be a good solution for long time work and good communication

Establishment of Technical Collaboration basis between Korea and France for the development of severe accident assessment computer code under high burnup condition

International Nuclear Information System (INIS)

Kim, H. D.; Kim, D. H.; Park, S. Y.; Park, J. H.

2005-10-01

This project was performed by KAERI in the frame of construction of the international cooperative basis on the nuclear energy. This was supported from MOST under the title of 'Establishment of Technical Collaboration basis between Korea and France for the development of severe accident assessment computer code under high burn up condition'. The current operating NPP are converting the burned fuel to the wasted fuel after burn up of 40 GWD/MTU. But in Korea, burn up of more than 60 GWD/MTU will be expected because of the high fuel efficiency but also cost saving for storing the wasted fuel safely. The domestic research for the purpose of developing the fuel and the cladding that can be used under the high burn up condition up to 100 GWD/MTU is in progress now. But the current computer code adopts the model and the data that are valid only up to the 40 GWD/MTU at most. Therefore the current model could not take into account the phenomena that may cause differences in the fission product release behavior or in the core damage process due to the high burn up operation (more than 40 GWD/MTU). To evaluate the safety of the NPP with the high burn up fuel, the improvement of current severe accident code against the high burn up condition is an important research item. Also it should start without any delay. Therefore, in this study, an expert group was constructed to establish the research basis for the severe accident under high burn up conditions. From this expert group, the research items regarding the high burn up condition were selected and identified through discussion and technical seminars. Based on these selected items, the meeting between IRSN and KAERI to find out the cooperative research items on the severe accident under the high burn up condition was held in the IRSN headquater in Paris. After the meeting, KAERI and IRSN agreed to cooperate with each other on the selected items, and to co-host the international seminar, and to develop the model and to

Analysis of molten fuel-coolant interaction during a reactivity-initiated accident experiment

International Nuclear Information System (INIS)

El-Genk, M.S.; Hobbins, R.R.

1981-01-01

The results of a reactivity-initiated accident experiment, designated RIA-ST-4, are discussed and analyzed with regard to molten fuel-coolant interaction (MFCI). In this experiment, extensive amounts of molten UO 2 fuel and zircaloy cladding were produced and fragmented upon mixing with the coolant. Coolant pressurization up to 35 MPa and coolant overheating in excess of 940 K occurred after fuel rod failure. The initial coolant conditions were similar to those in boiling water reactors during a hot startup (that is, coolant pressure of 6.45 MPa, coolant temperature of 538 K, and coolant flow rate of 85 cm 3 /s). It is concluded that the high coolant pressure recorded in the RIA-ST-4 experiment was caused by an energetic MFCI and was not due to gas release from the test rod at failure, Zr/water reaction, or to UO 2 fuel vapor pressure. The high coolant temperature indicated the presence of superheated steam, which may have formed during the expansion of the working fluid back to the initial coolant pressure; yet, the thermal-to-mechanical energy conversion ratio is estimated to be only 0.3%

RIA Analysis of Unprotected TRIGA Reactor

Directory of Open Access Journals (Sweden)

M.H. Altaf

2017-07-01

Full Text Available An RIA (reactivity initiated accident analysis has been carried out for the TRIGA Mark II research reactor considering both step and ramp reactivity ranges within 0.5 % dk/k (< $1 to 2.0 % dk/k (>$2. The insertion time was set at 10 s. Based on the fact that a reactor becomes unprotected if scram does not work at the event of danger, to define unprotected conditions, the time to actuate scram (trip was taken as close to total simulation time. In this long duration of scram inactivity, it is obtained from the present analysis that the reactor remained safe to up to 1.8 % dk/k ($2.57 for step reactivity and 1.99 % dk/k ($2.84 for ramp reactivity. In addition to negative temperature coefficient of reativity, probably the longer time of reactivity insertion keeps TRIGA safe even at larger magnitudes of reactivity during unprotected reactor transients. Coupled point kinetics, neutronics, and thermal hydraulics code EUREKA-2/R has been utilized for this work. It appears that EUREKA-2/RR predicts the sequence of unprotected transient scenario of TRIGA core with good approximation and the results will definitely be helpful for the reactor operators.

Nuclear Fuel Behaviour in Loss-of-coolant Accident (LOCA) Conditions

International Nuclear Information System (INIS)

Pettersson, Kjell; Chung, Haijung; ); Billone, Michael; Fuketa, Toyoshi; Nagase, Fumihisa; Grandjean, Claude; Hache, George; Papin, Joelle; Heins, Lothar; Hozer, Zoltan; In de Betou, Jan; Kelppe, Seppo; Mayer, Ralph; Scott, Harold; Voglewede, John; Sonnenburg, Heinz; Sunder, Sham; Valach, Mojmir; Vrtilkova, Vera; Waeckel, Nicolas; Wiesenack, Wolfgang; Zimmermann, Martin

2009-01-01

The NEA Working Group on Fuel Safety (WGFS) is tasked with advancing the current understanding of fuel safety issues by assessing the technical basis for current safety criteria and their applicability to high burn-up and to new fuel designs and materials. The group aims at facilitating international convergence in this area, including as regards experimental approaches and interpretation and the use of experimental data relevant for safety. In 1986, a working group of the NEA Committee on the Safety of Nuclear Installations (CSNI) issued a state-of-the-art report on water reactor fuel behaviour in design-basis accident (DBA) conditions. The 1986 report was limited to the oxidation, embrittlement and deformation of pressurised water reactor (PWR) fuel in a loss-of-coolant accident (LOCA). Since then, considerable experimental and analytical work has been performed, which has led to a broader and deeper understanding of LOCA-related phenomena. Further, new cladding alloys have been produced, which might behave differently than the previously used Zircaloy-4, both under normal operating conditions and during transients. Compared with 20 years ago, fuel burn-up has been significantly increased, which requires extending the LOCA database in order to cover the high burnup range. There was also a clear need to address LOCA performance for reactor types other than PWRs. The present report has been prepared by the WGFS and covers the following technical aspects: - Description of different LOCA scenarios for major types of reactors: BWRs, PWRs, VVERs and to a lesser extent CANDUs. - LOCA phenomena: ballooning, burst, oxidation, fuel relocation and possible fracture at quench. - Details of high-temperature oxidation behaviour of various cladding materials. - Metallurgical phase change, effect of hydrogen and oxygen on residual cladding ductility. - Methods for LOCA testing, for example two-sided oxidation and ring compression for ductility, and integral quench test for

Development of a diagnostic system for identifying accident conditions in a reactor

International Nuclear Information System (INIS)

Santhosh; Gera, B.; Kumar, Mithilesh; Thangamani, I.; Prasad, Hari; Srivastava, A.; Dutta, Anu; Sharma, Pavan K.; Majumdar, P.; Verma, V.; Mukhopadhyay, D.; Ganju, Sunil; Chatterjee, B.; Sanyasi Rao, V.V.S.; Lele, H.G.; Ghosh, A.K.

2009-07-01

This report describes a methodology for identification of accident conditions in a nuclear reactor from the signals available to the operator. A large database of such signals is generated through analyses - for core, containment, environmental dispersion and radiological dose to train a computer code based on an Artificial Neural Networks (ANNs). At present, in the prediction mode, information on LOCA (location and size of break), status of availability of ECCS, and expected doses can be predicted well for a 220 MWe PHWR. (author)

Assessment of WWER fuel condition in design basis accident

Energy Technology Data Exchange (ETDEWEB)

Bibilashvili, Yu; Sokolov, N; Andreeva-Andrievskaya, L; Vlasov, Yu; Nechaeva, O; Salatov, A [Vsesoyuznyj Nauchno-Issledovatel` skij Inst. Neorganicheskikh Materialov, Moscow (Russian Federation)

1994-12-31

The fuel behaviour in design basis accidents is assessed by means of the verified code RAPTA-5. The code uses a set of high temperature physico-chemical properties of the fuel components as determined for commercially produced materials, fuel rod simulators and fuel rod bundles. The WWER fuel criteria available in Russia for design basis accidents do not generally differ from the similar criteria adopted for PWR`s. 12 figs., 11 refs.

49 CFR 195.50 - Reporting accidents.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Reporting accidents. 195.50 Section 195.50 Transportation Other Regulations Relating to Transportation (Continued) PIPELINE AND HAZARDOUS MATERIALS SAFETY... PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.50 Reporting accidents. An accident...

Investigation of conditions inside the reactor building annulus of a PWR plant of KONVOI type in case of severe accidents with increased containment leakages

International Nuclear Information System (INIS)

Bakalov, Ivan; Sonnenkalb, Martin

2018-01-01

Improvements of the implemented severe accident management (SAM) concepts have been done in all operating German NPPs after the Fukushima Daiichi accidents following recommendations of the German Reactor Safety Commission (RSK) and as a result of the stress test being performed. The efficiency of newly developed severe accident management guidelines (SAMG) for a PWR KONVOI reference plant related to the mitigation of challenging conditions inside the reactor building (RB) annulus due to increased containment leakages during severe accidents have been assessed. Based on two representative severe accident scenarios the releases of both hydrogen and radionuclides into the RB annulus have been predicted with different boundary conditions. The accident scenarios have been analysed without and with the impact of several SAM measures (already planned or proposed in addition), which turned out to be efficient to mitigate the consequences. The work was done within the frame of a research project financially supported by the Federal Ministry BMUB.

Investigation of conditions inside the reactor building annulus of a PWR plant of KONVOI type in case of severe accidents with increased containment leakages

Energy Technology Data Exchange (ETDEWEB)

Bakalov, Ivan [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Berlin (Germany); Sonnenkalb, Martin [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Koeln (Germany)

2018-02-15

Improvements of the implemented severe accident management (SAM) concepts have been done in all operating German NPPs after the Fukushima Daiichi accidents following recommendations of the German Reactor Safety Commission (RSK) and as a result of the stress test being performed. The efficiency of newly developed severe accident management guidelines (SAMG) for a PWR KONVOI reference plant related to the mitigation of challenging conditions inside the reactor building (RB) annulus due to increased containment leakages during severe accidents have been assessed. Based on two representative severe accident scenarios the releases of both hydrogen and radionuclides into the RB annulus have been predicted with different boundary conditions. The accident scenarios have been analysed without and with the impact of several SAM measures (already planned or proposed in addition), which turned out to be efficient to mitigate the consequences. The work was done within the frame of a research project financially supported by the Federal Ministry BMUB.

The Influence of atmospheric conditions to probabilistic calculation of impact of radiology accident on PWR 1000 MWe

International Nuclear Information System (INIS)

Pande Made Udiyani; Sri Kuntjoro

2015-01-01

The calculation of the radiological impact of the fission products releases due to potential accidents that may occur in the PWR (Pressurized Water Reactor) is required in a probabilistic. The atmospheric conditions greatly contribute to the dispersion of radionuclides in the environment, so that in this study will be analyzed the influence of atmospheric conditions on probabilistic calculation of the reactor accidents consequences. The objective of this study is to conduct an analysis of the influence of atmospheric conditions based on meteorological input data models on the radiological consequences of PWR 1000 MWe accidents. Simulations using PC-Cosyma code with probabilistic calculations mode, the meteorological data input executed cyclic and stratified, the meteorological input data are executed in the cyclic and stratified, and simulated in Muria Peninsula and Serang Coastal. Meteorological data were taken every hour for the duration of the year. The result showed that the cumulative frequency for the same input models for Serang coastal is higher than the Muria Peninsula. For the same site, cumulative frequency on cyclic input models is higher than stratified models. The cyclic models provide flexibility in determining the level of accuracy of calculations and do not require reference data compared to stratified models. The use of cyclic and stratified models involving large amounts of data and calculation repetition will improve the accuracy of statistical calculation values. (author)

Fission product releases at severe LWR accident conditions: ORNL/CEA measurements versus calculations

Energy Technology Data Exchange (ETDEWEB)

Andre, B.; Ducros, G.; Leveque, J.P. [CEA Centre d`Etudes de Grenoble, 38 (France). Dept. de Thermohydraulique et de Physique; Osborne, M.F.; Lorenz, R.A. [Oak Ridge National Lab., TN (United States); Maro, D. [CEA Centre d`Etudes de Fontenay-aux-Roses, 92 (France). Dept. de Protection de l`Environnement et des Installations

1995-12-31

Experimental programs in the United States and France have followed similar paths in supplying much of the data needed to analyze severe accidents. Both the HI/VI program, conducted at the Oak Ridge National Laboratory (ORNL) under the sponsorship of the U. S. Nuclear Regulatory Commission (NRC), and the HEVA/VERCORS program, supported by IPSN-Commissariat a l`Energie Atomique (CEA) and carried out at the Centre d`Etudes Nucleaires de Grenoble, have studied fission product release from light water reactor (LWR) fuel samples during test sequences representative of severe accidents. Recognizing that more accurate data, i.e., a better defined source term, could reduce the safety margins included in the rather conservative source terms originating from WASH-1400, the primary objective of these programs has been to improve the data base concerning fission product release and behavior at high temperatures. To facilitate the comparison, a model based on fission product diffusion mechanisms that was developed at ORNL and adapted with CEA experimental data is proposed. This CEA model is compared with the ORNL experimental data in a blind test. The two experimental programs used similar techniques in out-of-pile studies. Highly irradiated fuel samples were heated in radiofrequency induction furnaces to very high temperatures (up to 2700 K at ORNL and 2750 K at CEA) in oxidizing (H{sub 2}O), reducing (H{sub 2}) or mixed (H{sub 2}O+H{sub 2}) environments. The experimental parameters, which were chosen from calculated accident scenarios, did not duplicate specific accidents, but rather emphasized careful control of test conditions to facilitate extrapolation of the results to a wide variety of accident situations. This paper presents a broad and consistent database from ORNL and CEA release results obtained independently since the early 1980`S. A comparison of CORSOR and CORSOR Booth calculations, currently used in safety analysis, and the experimental results is presented and

Occupational accidents among mototaxi drivers.

Science.gov (United States)

Amorim, Camila Rego; de Araújo, Edna Maria; de Araújo, Tânia Maria; de Oliveira, Nelson Fernandes

2012-03-01

The use of motorcycles as a means of work has contributed to the increase in traffic accidents, in particular, mototaxi accidents. The aim of this study was to estimate and characterize the incidence of occupational accidents among the mototaxis registered in Feira de Santana, BA. This is a cross-sectional study with descriptive and census data. Of the 300 professionals registered at the Municipal Transportation Service, 267 professionals were interviewed through a structured questionnaire. Then, a descriptive analysis was conducted and the incidence of accidents was estimated based on the variables studied. Relative risks were calculated and statistical significance was determined using the chi-square test and Fisher's exact test, considering p accidents were observed in 10.5% of mototaxis. There were mainly minor injuries (48.7%), 27% of them requiring leaves of absence from work. There was an association between the days of work per week, fatigue in lower limbs and musculoskeletal complaints, and accidents. Knowledge of the working conditions and accidents involved in this activity can be of great importance for the adoption of traffic education policies, and to help prevent accidents by improving the working conditions and lives of these professionals.

Accidents and emergency conditions: Legal aspects

International Nuclear Information System (INIS)

Peinsipp, N.

1985-01-01

The currently valid versions of the Federal German Atomic Energy Act, the Radiation Protection Ordinance, and the X-Ray Ordinance show differences with regard to the use of the terms 'accident' or 'emergency', respectively, preferring either one or the other term, or using both terms. The author comments on this lack of harmonization in terminology and goes into details on aspects such as legislation and application of law. (DG) [de

Simulation of experiment on aerosol behaviour at severe accident conditions in the LACE experimental facility with the ASTEC CPA code

International Nuclear Information System (INIS)

Kljenak, I.; Mavko, B.

2007-01-01

The experiment LACE LA4 on thermal-hydraulics and aerosol behavior in a nuclear power plant containment, which was performed in the LACE experimental facility, was simulated with the ASTEC CPA module of the severe accident computer code ASTEC V1.2. The specific purpose of the work was to assess the capability of the module (code) to simulate thermal-hydraulic conditions and aerosol behavior in the containment of a light-water-reactor nuclear power plant at severe accident conditions. The test was simulated with boundary conditions, described in the experiment report. Results of thermal-hydraulic conditions in the test vessel, as well as dry aerosol concentrations in the test vessel atmosphere, are compared to experimental results and analyzed. (author)

Out-of-pile test of zirconium cladding simulating reactivity initiated accident

Energy Technology Data Exchange (ETDEWEB)

Kim, J. H.; Lee, M. H.; Choi, B. K.; Bang, J. K.; Jung, Y. H. [KAERI, Taejon (Korea, Republic of)

2004-07-01

Mechanical properties of zirconium cladding such as Zircaloy-4 and advanced cladding were evaluated by ring tension test to simulate Reactivity-Initiated Accident (RIA) as an out-pile test. Cladding was hydrided by means of charging hydrogen up to 1000ppm to simulate high-burnup situation, finally fabricated to circumferential tensile specimen. Ring tension test was carried out from 0.01 to 1/sec to keep pace with actual RIA event. The results showed that mechanical strength of zirconium cladding increased at the value of 7.8% but ductility decreased at the 34% as applied strain rate and absorbed hydrogen increased. Further activities regarding out-of-pile testing plans for simulated high-burnup cladding were discussed in this paper.

Design feasibility study on corium stabilization in bottom end-fitting for AHWR under accident condition

International Nuclear Information System (INIS)

Gokhale, Onkar; Mukhopadhyay, D.; Chatterjee, B.; Singh, R.K.

2015-01-01

Advanced Heavy Water Reactor (AHWR) is being designed in a robust way to cater both Design and Beyond Design Basis Accidents to meet all the safety functions. All the functions are met by passive means with special emphasis on 'residual heat removal' which is catered by passive natural circulation mode. In context to Design Basis Accidents, several features are designed to handle worst kind of scenario like Station Black Out. For Design Extension Conditions (DEC), the means of passive natural circulation is adopted as a design means to meet the DEC-A conditions like cooling of moderator by natural circulation means with GDWP inventory. Under the DEC-B condition where large scale of fuel melting is envisaged, a core catcher is designed with active/passive cooling modes to take care of the residual heat of the core. All the mentioned features utilizes the natural mode of heat transfer to meet one of the safety function i.e. 'residual heat removal'. The analysis shows that the tube sheet as well as lattice tube temperatures remain low and are able to take out the heat from corium through sub-cooled nucleate boiling. The ES cooling is sufficient to maintain the cooling water in subcooled condition. The integrity of tube sheet and lattice tube is maintained

Basic study on BWR plant behavior under the condition of severe accident (2)

International Nuclear Information System (INIS)

Ozaki, Yoshihiko; Ueda, Masataka; Sasaki, Hajime

2016-01-01

In this paper, we report on the results using the BWR plant simulator about the plant behavior under the condition of the two types of severe accidents that LOCA occurs but ECCS fails the water irrigation into the reactor core and SBO occurs and at the same time the reclosed failure of SRV occurs. The simulation experiments were carried out for the cases that LOCA has occurred in the main feed-water piping. As for the results about the relationship between the LOCA area and the time from LOCA occurs until the fuel temperature rise start, the effect that RCIC operated was extremely big for small and middle LOCA area. In the case of main feed-water system LOCA, the core water level suddenly decreased for large LOCA of 2000 cm"2 area, however, if the irrigation into the reactor core was carried out 30 min after LOCA occurrence, the core had little damage. In addition, the H_2 concentration in the containment vessel did not exceed both limits of H_2 explosion nor detonation. The pressure of the containment vessel was around 3 kg/cm"2 of design value, so the soundness of the containment vessel was confirmed. On the other hand, for the accident of SBO with reclosed failure of SRV, it has been shown that the accidents continue to progress rapidly as compared with the case of normally operating of SRV. Because SRV has the function that keep the inside pressure of reactor core by repeating opened and closed in response of the inside pressure and prevent the decrease of water level inside reactor core. However, if the irrigation into the reactor core was carried out 30 min after SBO occurrence, the core had little damage and also the H_2 concentration in the containment vessel did not exceed limits of H_2 explosion. Further, as for the accident of reclosed failure of SRV, it has been shown that there are very good correspondence with the simulation results of main steam piping LOCA of area 180 cm"2 corresponding to the inlet cross-sectional area SRV installed on the piping

Assessment of potential doses to workers during postulated accident conditions at the Waste Isolation Pilot Plant

Energy Technology Data Exchange (ETDEWEB)

Hoover, M.D.; Farrell, R.F. [DOE, Carlsbad, NM (United States); Newton, G.J.

1995-12-01

The recent 1995 WIPP Safety Analysis Report (SAR) Update provided detailed analyses of potential radiation doses to members of the public at the site boundary during postulated accident scenarios at the U.S. Department of Energy`s Waste Isolation Pilot Plant (WIPP). The SAR Update addressed the complete spectrum of potential accidents associated with handling and emplacing transuranic waste at WIPP, including damage to waste drums from fires, punctures, drops, and other disruptions. The report focused on the adequacy of the multiple layers of safety practice ({open_quotes}defense-in-depth{close_quotes}) at WIPP, which are designed to (1) reduce the likelihood of accidents and (2) limit the consequences of those accidents. The safeguards which contribute to defense-in-depth at WIPP include a substantial array of inherent design features, engineered controls, and administrative procedures. The SAR Update confirmed that the defense-in-depth at WIPP is adequate to assure the protection of the public and environment. As a supplement to the 1995 SAR Update, we have conducted additional analyses to confirm that these controls will also provide adequate protection to workers at the WIPP. The approaches and results of the worker dose assessment are summarized here. In conformance with the guidance of DOE Standard 3009-94, we emphasize that use of these evaluation guidelines is not intended to imply that these numbers constitute acceptable limits for worker exposures under accident conditions. However, in conjunction with the extensive safety assessment in the 1995 SAR Update, these results indicate that the Carlsbad Area Office strategy for the assessment of hazards and accidents assures the protection of workers, members of the public, and the environment.

Contributing factors in construction accidents.

Science.gov (United States)

Haslam, R A; Hide, S A; Gibb, A G F; Gyi, D E; Pavitt, T; Atkinson, S; Duff, A R

2005-07-01

This overview paper draws together findings from previous focus group research and studies of 100 individual construction accidents. Pursuing issues raised by the focus groups, the accident studies collected qualitative information on the circumstances of each incident and the causal influences involved. Site based data collection entailed interviews with accident-involved personnel and their supervisor or manager, inspection of the accident location, and review of appropriate documentation. Relevant issues from the site investigations were then followed up with off-site stakeholders, including designers, manufacturers and suppliers. Levels of involvement of key factors in the accidents were: problems arising from workers or the work team (70% of accidents), workplace issues (49%), shortcomings with equipment (including PPE) (56%), problems with suitability and condition of materials (27%), and deficiencies with risk management (84%). Employing an ergonomics systems approach, a model is proposed, indicating the manner in which originating managerial, design and cultural factors shape the circumstances found in the work place, giving rise to the acts and conditions which, in turn, lead to accidents. It is argued that attention to the originating influences will be necessary for sustained improvement in construction safety to be achieved.

Simulation of the transient processes of load rejection under different accident conditions in a hydroelectric generating set

Science.gov (United States)

Guo, W. C.; Yang, J. D.; Chen, J. P.; Peng, Z. Y.; Zhang, Y.; Chen, C. C.

2016-11-01

Load rejection test is one of the essential tests that carried out before the hydroelectric generating set is put into operation formally. The test aims at inspecting the rationality of the design of the water diversion and power generation system of hydropower station, reliability of the equipment of generating set and the dynamic characteristics of hydroturbine governing system. Proceeding from different accident conditions of hydroelectric generating set, this paper presents the transient processes of load rejection corresponding to different accident conditions, and elaborates the characteristics of different types of load rejection. Then the numerical simulation method of different types of load rejection is established. An engineering project is calculated to verify the validity of the method. Finally, based on the numerical simulation results, the relationship among the different types of load rejection and their functions on the design of hydropower station and the operation of load rejection test are pointed out. The results indicate that: The load rejection caused by the accident within the hydroelectric generating set is realized by emergency distributing valve, and it is the basis of the optimization for the closing law of guide vane and the calculation of regulation and guarantee. The load rejection caused by the accident outside the hydroelectric generating set is realized by the governor. It is the most efficient measure to inspect the dynamic characteristics of hydro-turbine governing system, and its closure rate of guide vane set in the governor depends on the optimization result in the former type load rejection.

Prevalence of oral health-related conditions that could trigger accidents for patients with moderate-to-severe dementia.

Science.gov (United States)

Kobayashi, Naoki; Soga, Yoshihiko; Maekawa, Kyoko; Kanda, Yuko; Kobayashi, Eiko; Inoue, Hisako; Kanao, Ayana; Himuro, Yumiko; Fujiwara, Yumi

2017-03-01

This study was performed to determine the prevalence of oral health conditions unnoticed by doctors and ward staff that may increase risk of incidents and/or accidents in hospitalised patients with moderate-severe dementia. Dementia patients may not recognise risks in the mouth, such as tooth mobility or ill-fitting dental prostheses and/or dentures. In addition to the risk of choking, injury by sharp edges of collapsed teeth or prosthodontics could pose risks. However, many previous publications were limited to case reports or series. Ninety-two consecutive hospitalised dementia patients (M: 52, F: 40, median age: 82.5 years, range: 62-99 years, from 2011 to 2014), referred for dentistry for dysphagia rehabilitation, were enrolled in this study. Participants referred for dental treatment with dental problems detected by ward staff were excluded. All participants had a Global Clinical Dementia Rating Score >2. Their dental records were evaluated retrospectively for issues that may cause incidents and/or accidents. Problems in the mouth, for example tooth stumps, dental caries, and ill-fitting dentures, were detected in 51.1% of participants (47/92). Furthermore, 23.9% (22/92) showed risk factors that could lead to incidents and/or accidents, for example falling out of teeth and/or prosthodontics or injury by sharp edges of teeth and/or prosthodontics. Hospitalised moderate-severe dementia patients had a high prevalence of oral health conditions unnoticed by doctors and ward staff that may increase risk of incidents and/or accidents. © 2016 John Wiley & Sons A/S and The Gerodontology Association. Published by John Wiley & Sons Ltd.

Fuel behaviour in the case of severe accidents and potential ATF designs. Fuel Behavior in Severe Accidents and Potential Accident Tolerance Fuel Designs

International Nuclear Information System (INIS)

Cheng, Bo

2013-01-01

This presentation reviews the conditions of fuel rods under severe loss of coolant conditions, approaches that may increase coping time for plant operators to recover, requirements of advanced fuel cladding to increase tolerance in accident conditions, potential candidate alloys for accident-tolerant fuel cladding and a novel design of molybdenum (Mo) -based fuel cladding. The current Zr-alloy fuel cladding will lose all its mechanical strength at 750-800 deg. C, and will react rapidly with high-pressure steam, producing significant hydrogen and exothermic heat at 700-1000 deg. C. The metallurgical properties of Zr make it unlikely that modifications of the Zr-alloy will improve the behaviour of Zr-alloys at temperatures relevant to severe accidents. The Mo-based fuel cladding is designed to (1) maintain fuel rod integrity, and reduce the release rate of hydrogen and exothermic heat in accident conditions at 1200-1500 deg. C. The EPRI research has thus far completed the design concepts, demonstration of feasibility of producing very thin wall (0.2 mm) Mo tubes. The feasibility of depositing a protective coating using various techniques has also been demonstrated. Demonstration of forming composite Mo-based cladding via mechanical reduction has been planned

Mitigative techniques and analysis of generic site conditions for ground-water contamination associated with severe accidents

Energy Technology Data Exchange (ETDEWEB)

Shafer, J.M.; Oberlander, P.L.; Skaggs, R.L.

1984-04-01

The purpose of this study is to evaluate the feasibility of using ground-water contaminant mitigation techniques to control radionuclide migration following a severe commercial nuclear power reactor accident. The two types of severe commercial reactor accidents investigated are: (1) containment basemat penetration of core melt debris which slowly cools and leaches radionuclides to the subsurface environment, and (2) containment basemat penetration of sump water without full penetration of the core mass. Six generic hydrogeologic site classifications are developed from an evaluation of reported data pertaining to the hydrogeologic properties of all existing and proposed commercial reactor sites. One-dimensional radionuclide transport analyses are conducted on each of the individual reactor sites to determine the generic characteristics of a radionuclide discharge to an accessible environment. Ground-water contaminant mitigation techniques that may be suitable, depending on specific site and accident conditions, for severe power plant accidents are identified and evaluated. Feasible mitigative techniques and associated constraints on feasibility are determined for each of the six hydrogeologic site classifications. The first of three case studies is conducted on a site located on the Texas Gulf Coastal Plain. Mitigative strategies are evaluated for their impact on contaminant transport and results show that the techniques evaluated significantly increased ground-water travel times. 31 references, 118 figures, 62 tables.

Mitigative techniques and analysis of generic site conditions for ground-water contamination associated with severe accidents

International Nuclear Information System (INIS)

Shafer, J.M.; Oberlander, P.L.; Skaggs, R.L.

1984-04-01

The purpose of this study is to evaluate the feasibility of using ground-water contaminant mitigation techniques to control radionuclide migration following a severe commercial nuclear power reactor accident. The two types of severe commercial reactor accidents investigated are: (1) containment basemat penetration of core melt debris which slowly cools and leaches radionuclides to the subsurface environment, and (2) containment basemat penetration of sump water without full penetration of the core mass. Six generic hydrogeologic site classifications are developed from an evaluation of reported data pertaining to the hydrogeologic properties of all existing and proposed commercial reactor sites. One-dimensional radionuclide transport analyses are conducted on each of the individual reactor sites to determine the generic characteristics of a radionuclide discharge to an accessible environment. Ground-water contaminant mitigation techniques that may be suitable, depending on specific site and accident conditions, for severe power plant accidents are identified and evaluated. Feasible mitigative techniques and associated constraints on feasibility are determined for each of the six hydrogeologic site classifications. The first of three case studies is conducted on a site located on the Texas Gulf Coastal Plain. Mitigative strategies are evaluated for their impact on contaminant transport and results show that the techniques evaluated significantly increased ground-water travel times. 31 references, 118 figures, 62 tables

Abnormal Signal Analysis for a Change of the R-C Passive Elements in a Equivalent Circuit Modeling under a High Temperature Accident Condition

International Nuclear Information System (INIS)

Koo, Kil-Mo; Song, Yong-Mann; Ahan, Kwang-Il; Ha, Jea-Joo

2007-01-01

An electrical signal should be checked to see whether it lies within its expected electrical range when there is a doubtful condition. The normal signal level for pressure, flow, level and resistance temperature detector sensors is 4 - 20mA for most instruments as an industrial process control standard. In the case of an abnormal signal level from an instrument under a severe accident condition, it is necessary to obtain a more accurate signal validation to operate a system in a control room in NPPs. Diagnostics and analysis for some abnormal signals have been performed through an important equivalent circuits modeling for passive elements under severe accident conditions. Unlike the design basis accidents, there are some inherent uncertainties for the instrumentation capabilities under severe accident conditions. In this paper, to implement a diagnostic analysis for an equivalent circuits modeling, a kind of linked LabVIEW program for each PSpice and MULTISim code is introduced as a one body order system, which can obtain some abnormal signal patterns by a special function such as an advanced simulation tool for each PSpice and Multi-SIM code as a means of a function for a PC based ASSA (abnormal signal simulation analyzer) module

Abnormal Signal Analysis for a Change of the R-C Passive Elements in a Equivalent Circuit Modeling under a High Temperature Accident Condition

Energy Technology Data Exchange (ETDEWEB)

Koo, Kil-Mo; Song, Yong-Mann; Ahan, Kwang-Il; Ha, Jea-Joo [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2007-07-01

An electrical signal should be checked to see whether it lies within its expected electrical range when there is a doubtful condition. The normal signal level for pressure, flow, level and resistance temperature detector sensors is 4 - 20mA for most instruments as an industrial process control standard. In the case of an abnormal signal level from an instrument under a severe accident condition, it is necessary to obtain a more accurate signal validation to operate a system in a control room in NPPs. Diagnostics and analysis for some abnormal signals have been performed through an important equivalent circuits modeling for passive elements under severe accident conditions. Unlike the design basis accidents, there are some inherent uncertainties for the instrumentation capabilities under severe accident conditions. In this paper, to implement a diagnostic analysis for an equivalent circuits modeling, a kind of linked LabVIEW program for each PSpice and MULTISim code is introduced as a one body order system, which can obtain some abnormal signal patterns by a special function such as an advanced simulation tool for each PSpice and Multi-SIM code as a means of a function for a PC based ASSA (abnormal signal simulation analyzer) module.

Studies on the role of molybdenum on iodine transport in the RCS in nuclear severe accident conditions

International Nuclear Information System (INIS)

Grégoire, A.-C.; Kalilainen, J.; Cousin, F.; Mutelle, H.; Cantrel, L.; Auvinen, A.; Haste, T.; Sobanska, S.

2015-01-01

Highlights: • In oxidising conditions, Mo reacts with Cs and thus promotes gaseous iodine release. • In reducing conditions, CsI remains the dominant form for released iodine. • The nature of released iodine is well reproduced by the ASTEC code. - Abstract: The effect of molybdenum on iodine transport in the reactor coolant system (RCS) under PWR severe accident conditions was investigated in the framework of the EU SARNET project. Experiments were conducted at the VTT-Institute and at IRSN and simulations of the experimental results were performed with the ASTEC severe accident simulation code. As molybdenum affects caesium chemistry by formation of molybdates, it may have a significant impact on iodine transport in the RCS. Experimentally it has been shown that the formation of gaseous iodine is promoted in oxidising conditions, as caesium can be completely consumed to form caesium polymolybdates and is thus not available for reacting with gaseous iodine and leading to CsI aerosols. In reducing conditions, CsI remains the dominant form of iodine, as the amount of oxygen is not sufficient to allow formation of quantitative caesium polymolybdates. An I–Mo–Cs model has been developed and it reproduces well the experimental trends on iodine transport

Evaluation of High-Pressure RCS Natural Circulations Under Severe Accident Conditions

International Nuclear Information System (INIS)

Lee, Byung Chul; Bang, Young Suk; Suh, Nam Duk

2006-01-01

Since TMI-2 accident, the occurrence of severe accident natural circulations inside RCS during entire in-vessel core melt progressions before the reactor vessel breach had been emphasized and tried to clarify its thermal-hydraulic characteristics. As one of consolidated outcomes of these efforts, sophisticated models have been presented to explain the effects of a variety of engineering and phenomenological factors involved during severe accident mitigation on the integrity of RCS pressure boundaries, i.e. reactor pressure vessel(RPV), RCS coolant pipe and steam generator tubes. In general, natural circulation occurs due to density differences, which for single phase flow, is typically generated by temperature differences. Three natural circulation flows can be formed during severe accidents: in-vessel, hot leg countercurrent flow and flow through the coolant loops. Each of these flows may be present during high-pressure transients such as station blackout (SBO) and total loss of feedwater (TLOFW). As a part of research works in order to contribute on the completeness of severe accident management guidance (SAMG) in domestic plants by quantitatively assessing the RCS natural circulations on its integrity, this study presents basic approach for this work and some preliminary results of these efforts with development of appropriately detailed RCS model using MELCOR computer code

Status Report on Spent Fuel Pools under Loss-of-Cooling and Loss-of-Coolant Accident Conditions - Final Report

International Nuclear Information System (INIS)

Adorni, M.; Esmaili, H.; Grant, W.; Hollands, T.; Hozer, Z.; Jaeckel, B.; Munoz, M.; Nakajima, T.; Rocchi, F.; Strucic, M.; ); Tregoures, N.; Vokac, P.; Ahn, K.I.; Bourgue, L.; Dickson, R.; Douxchamps, P.A.; Herranz, L.E.; Jernkvist, L.O.; Amri, A.; Kissane, M.P.; )

2015-01-01

Following the 2011 accident at the Fukushima Daiichi Nuclear Power Station, the Nuclear Energy Agency Committee on the Safety of Nuclear Installations decided to launch several high-priority activities to address certain technical issues. Among other things, it was decided to prepare a status report on spent fuel pools (SFPs) under loss of cooling accident conditions. This activity was proposed jointly by the CSNI Working Group on Analysis and Management of Accidents (WGAMA) and the Working Group on Fuel Safety (WGFS). The main objectives, as defined by these working groups, were to: - Produce a brief summary of the status of SFP accident and mitigation strategies, to better contribute to the post-Fukushima accident decision making process; - Provide a brief assessment of current experimental and analytical knowledge about loss of cooling accidents in SFPs and their associated mitigation strategies; - Briefly describe the strengths and weaknesses of analytical methods used in codes to predict SFP accident evolution and assess the efficiency of different cooling mechanisms for mitigation of such accidents; - Identify and list additional research activities required to address gaps in the understanding of relevant phenomenological processes, to identify where analytical tool deficiencies exist, and to reduce the uncertainties in this understanding. The proposed activity was agreed and approved by CSNI in December 2012, and the first of four meetings of the appointed writing group was held in March 2013. The writing group consisted of members of the WGAMA and the WGFS, representing the European Commission and the following countries: Belgium, Canada, Czech Republic, France, Germany, Hungary, Italy, Japan, Korea, Spain, Sweden, Switzerland and the USA. This report mostly covers the information provided by these countries. The report is organised into 8 Chapters and 4 Appendices: Chapter 1: Introduction; Chapter 2: Spent fuel pools; Chapter 3: Possible accident

Accidents - Chernobyl accident; Accidents - accident de Tchernobyl

Energy Technology Data Exchange (ETDEWEB)

NONE

2004-07-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Applicability of simplified methods to evaluate consequences of criticality accident using past accident data

International Nuclear Information System (INIS)

Nakajima, Ken

2003-01-01

Applicability of four simplified methods to evaluate the consequences of criticality accident was investigated. Fissions in the initial burst and total fissions were evaluated using the simplified methods and those results were compared with the past accident data. The simplified methods give the number of fissions in the initial burst as a function of solution volume; however the accident data did not show such tendency. This would be caused by the lack of accident data for the initial burst with high accuracy. For total fissions, simplified almost reproduced the upper envelope of the accidents. However several accidents, which were beyond the applicable conditions, resulted in the larger total fissions than the evaluations. In particular, the Tokai-mura accident in 1999 gave in the largest total specific fissions, because the activation of cooling system brought the relatively high power for a long time. (author)

The modeling of fuel rod behaviour under RIA conditions in the code DYN3D

International Nuclear Information System (INIS)

Rohde, U.

1998-01-01

A description of the fuel rod behaviour and heat transfer model used in the code DYN3D for nuclear reactor core dynamic simulations is given. Besides the solution of heat conduction equations in fuel and cladding, the model comprises detailed description of heat transfer in the gas gap by conduction, radiation and fuel-cladding contact. The gas gap behaviour is modeled in a mechanistic way taking into account transient changes of the gas gap parameters based on given conditions for the initial state. Thermal, elastic and plastic deformations of fuel and cladding are taken into account within 1D approximation. Numerical studies concerning the fuel rod behaviour under RIA conditions in power reactors are reported. Fuel rod behaviour at high pressures and flow rates in power reactors is different from the behaviour under atmospheric pressure and stagnant flow conditions in the experiments. The mechanisms of fuel rod failure for fresh and burned fuel reported from the literature can be qualitatively reproduced by the DYN3D model. (author)

Numerical module for debris behavior under severe accident conditions

International Nuclear Information System (INIS)

Kisselev, A.E.; Kobelev, G.V.; Strizhov, V.F.; Vasiliev, A.D.

2005-01-01

The late phase of a hypothetical severe accident in a nuclear reactor is characterized by the appearance of porous debris and liquid pools in core region and lower head of the reactor vessel. Thermal hydraulics and heat transfer in these regions are very important for adequate analysis of severe accident dynamics. The purpose of this work is to develop a universal module which is able to model above-mentioned phenomena on the basis of modern physical concepts. The original approach for debris evolution is developed from classical principles using a set of parameters including debris porosity; average particle diameter; temperatures and mass fractions of solid, liquid and gas phases; specific interface areas between different phases; effective thermal conductivity of each phase, including radiative heat conductivity; mass and energy fluxes through the interfaces. The calculation results of several tests on modeling of porous debris behavior, including the MP-1 experiment, are presented in comparison with experimental data. The results are obtained using this module implemented into the Russian best estimate code, RATEG/SVECHA/HEFEST, which was developed for modeling severe accident thermal hydraulics and late phase phenomena in VVER nuclear power plants. (author)

JAERI's activities in JCO accident

International Nuclear Information System (INIS)

2000-09-01

The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

Diagnostic and prognostic system for identification of accident scenarios and prediction of 'source term' in nuclear power plants under accident conditions

International Nuclear Information System (INIS)

Santhosh; Gera, B.; Kumar, Mithilesh

2014-01-01

Nuclear power plant experiences a number of transients during its operations. These transients may be due to equipment failure, malfunctioning of process support systems etc. In such a situation, the plant may result in an abnormal state which is undesired. In case of such an undesired plant condition, the operator has to carry out diagnostic and corrective actions. When an event occurs starting from the steady state operation, instruments' readings develop a time dependent pattern and these patterns are unique with respect to the type of the particular event. Therefore, by properly selecting the plant process parameters, the transients can be distinguished. In this connection, a computer based tool known as Diagnostic and Prognostic System has been developed for identification of large pipe break scenarios in 220 MWe Pressurised Heavy Water Reactors (PHWRs) and for prediction of expected 'Source Term' and consequence for a situation where Emergency Core Cooling System (ECCS) is not available or partially available. Diagnostic and Prognostic System is essentially a transient identification and expected source term forecasting system. The system is based on Artificial Neural Networks (ANNs) that continuously monitors the plant conditions and identifies a Loss Of Coolant Accident (LOCA) scenario quickly based on the reactor process parameter values. The system further identifies the availability of injection of ECCS and in case non-availability of ECCS, it can forecast expected 'Source Term'. The system is a support to plant operators as well as for emergency preparedness. The ANN is trained with a process parameter database pertaining to accident conditions and tested against blind exercises. In order to see the feasibility of implementing in the plant for real-time diagnosis, this system has been set up on a high speed computing facility and has been demonstrated successfully for LOCA scenarios. (author)

Simulation of KAEVER experiments on aerosol behavior in a nuclear power plant containment at accident conditions with the ASTEC code

International Nuclear Information System (INIS)

Kljenak, I.; Mavko, B.

2006-01-01

Experiments on aerosol behaviour in saturated and non-saturated atmosphere, which were performed in the KAEVER experimental facility, were simulated with the severe accident computer code ASTEC CPA V1.2. The specific purpose of the work was to assess the capability of the code to model aerosol condensation and deposition in the containment of a light-water-reactor nuclear power plant at severe accident conditions, if the atmosphere saturation conditions are simulated adequately. Five different tests were first simulated with boundary conditions, obtained from the experiments. In all five tests, a non-saturated atmosphere was simulated, although, in four tests, the atmosphere was allegedly saturated. The simulations were repeated with modified boundary conditions, to obtain a saturated atmosphere in all tests. Results of dry and wet aerosol concentrations in the test vessel atmosphere for both sets of simulations are compared to experimental results. (author)

Effect of marine condition on feature of natural circulation after accident in floating nuclear power plant

International Nuclear Information System (INIS)

Yang Fan; Zhang Dan; Tan Changlu; Ran Xu; Yu Hongxing

2015-01-01

The incline and swing effect on natural circulation of floating nuclear power plant under site black out (SBO) accident is studied using self-developing marine condition system code RELAP5/MC. It shows that, for floating nuclear power plant under marine condition, the pressurizer fluctuating flow rate, the parallel heat sink (steam generator) have significant influences on the direct passive reactor heat removal (PRHR) system, which is different from other secondary PRHR under marine condition. The flow exchange between the loop and the pressurizer have major effect on cooling capacity for the left side loop. (authors)

Thermal hydraulic behavior of a PWR under beyond-design-basis accident conditions: Conclusions from an experimental program in a 4-loop test facility (PKL)

International Nuclear Information System (INIS)

Umminger, K.J.; Kastner, W.; Mandl, R.M.; Weber, P.

1993-01-01

Within the scope of German reactor safety research, extensive experiments covering the behavior of nuclear power plants under accident conditions have been carried out in the PKL test facility which simulates a 4-loop, 1,300 MWe KWU-designed PWR. While the investigations dealing with design-basis accidents and with the efficiency of the emergency core cooling systems have been largely completed, the main interest nowadays concentrates on the investigation of beyond-design-basis accidents to demonstrate the safety margins of nuclear power plants and to investigate the contribution of the built-in safety features for a further reduction of the residual risk. The thermal hydraulic behavior of a PWR under these extreme accident conditions was experimentally investigated within the PKL III B test program. This paper presents the fundamental findings with some of the most important results being discussed in detail. Future plans are also outlined

Underreporting of maritime accidents to vessel accident databases.

Science.gov (United States)

Hassel, Martin; Asbjørnslett, Bjørn Egil; Hole, Lars Petter

2011-11-01

Underreporting of maritime accidents is a problem not only for authorities trying to improve maritime safety through legislation, but also to risk management companies and other entities using maritime casualty statistics in risk and accident analysis. This study collected and compared casualty data from 01.01.2005 to 31.12.2009, from IHS Fairplay and the maritime authorities from a set of nations. The data was compared to find common records, and estimation of the true number of occurred accidents was performed using conditional probability given positive dependency between data sources, several variations of the capture-recapture method, calculation of best case scenario assuming perfect reporting, and scaling up a subset of casualty information from a marine insurance statistics database. The estimated upper limit reporting performance for the selected flag states ranged from 14% to 74%, while the corresponding estimated coverage of IHS Fairplay ranges from 4% to 62%. On average the study results document that the number of unreported accidents makes up roughly 50% of all occurred accidents. Even in a best case scenario, only a few flag states come close to perfect reporting (94%). The considerable scope of underreporting uncovered in the study, indicates that users of statistical vessel accident data should assume a certain degree of underreporting, and adjust their analyses accordingly. Whether to use correction factors, a safety margin, or rely on expert judgment, should be decided on a case by case basis. Copyright © 2011 Elsevier Ltd. All rights reserved.

Strategy generation in accident management support

International Nuclear Information System (INIS)

Sirola, M.

1995-01-01

An increased interest for research in the field of Accident Management can be noted. Several international programmes have been started in order to be able to understand the basic physical and chemical phenomena in accident conditions. A feasibility study has shown that it would be possible to design and develop a computerized support system for plant staff in accident situations. To achieve this goal the Halden Project has initiated a research programme on Computerized Accident Management Support (CAMS project). The aim is to utilize the capabilities of computerized tools to support the plant staff during the various accident stages. The system will include identification of the accident state, assessment of the future development of the accident and planning of accident mitigation strategies. A prototype is developed to support operators and the Technical Support Centre in decision making during serious accident in nuclear power plants. A rule based system has been built to take care of the strategy generation. This system assists plant personnel in planning control proposals and mitigation strategies from normal operation to severe accident conditions. The ideal of a safety objective tree and knowledge from the emergency procedures have been used. Future prediction requires good state identification of the plant status and some knowledge about the history of some critical variables. The information needs to be validated as well. Accurate calculations in simulators and a large database including all important information form the plant will help the strategy planning. (author). 12 refs, 2 figs

Study of heat and mass transfer phenomena in fuel assembly models under accident conditions

International Nuclear Information System (INIS)

Yefanov, A.D.; Kalyakin, C.G.; Loshchinin, V.M.; Pomet'ko, R.S.; Sergeev, V.V.; Shumsky, R.V.

1996-01-01

The majority of the material in support of the thermal - hydraulic safety of WWER core was obtained on single - assembly models containing a relatively small number of elements - heater rods. Upgrading the requirements to the reactor safety leads to the necessity for studying phenomena in channels representing the cross - sectional core dimensions and non - uniform radial power generation. Under such conditions, the contribution of natural convection can be significant in some core zones, including the occurrence of reverse flows and interchannel instability. These phenomena can have an important influence on heat transfer processes. Such influence is especially drastical under accident conditions associated with ceasing the forced circulation over the circuit. A number of urgent reactor safety problems at low operating parameters is related with the computer code verification and certification. One of the important trends in the reactor safety research is concerned with the rod bundle reflooding and verificational calculations of this phenomenon. To assess the water cooled reactor safety, the best fit computer codes are employed, which make it possible to simulate accident and transient operating conditions in a reactor installation. One of the most widely known computer codes is the RELAP5/MOD3 Code. The paper presents the comparison of the results calculated using this computer code with the test data on 4 - rod bundle quenching, which were obtained at the SSCRF-IPPE. Recently, the investigations on the steam - zirconium reaction kinetics have been performed at the SSCFR-IPPE and are being presently performed for the purpose of developing new and verifying available computer codes. (author). 3 refs, 6 figs

Investigation of Focusing Effect according to the Cooling Condition and Height of the Metallic layer in a Severe Accident

Energy Technology Data Exchange (ETDEWEB)

Moon, Je-Young; Chung, Bum-Jin [Kyung Hee University, Yongin (Korea, Republic of)

2015-05-15

The Fukushima nuclear power plant accident has led to renewed research interests in severe accidents of nuclear power plants. In-Vessel Retention (IVR) of core melt is one of key severe accident management strategies adopted in nuclear power plant design. The metallic layer is heated from below by the radioactive decay heat generated at the oxide pool, and is cooled from above and side walls. During the IVR process, reactor vessel may be cooled externally (ERVC) and the heat fluxes to the side wall increase with larger temperature difference than above. This {sup F}ocusing effect{sup i}s varied by cooling condition of upper boundary and height of the metallic layer. A sulfuric acid–copper sulfate (H{sub 2}SO{sub 4} - CuSO{sub 4}) electroplating system was adopted as the mass transfer system. Numerical analysis using the commercial CFD program FLUENT 6.3 were carried out with the same material properties and cooling conditions to examine the variation of the cell. The experimental and numerical studies were performed to investigate the focusing effect according to cooling condition of upper boundary and the height in metallic layer. The height of the side wall was varied for three different cooling conditions: top only, side only, and both top and side. Mass transfer experiments, based on the analogy concept, were carried out in order to achieve high Rayleigh number. The experimental results agreed well with the Rayleigh-Benard convection correlations of Dropkin and Somerscales and Globe and Dropkin. The heat transfer on side wall cooling condition without top cooling is highest and was enhanced by decreasing the aspect ratio. The numerical results agreed well with the experimental results. Each cell pattern (cell size, cell direction, central location of cell) differed in the cooling condition. Therefore, it is difficult to predict the internal flow due to complexity of cell formation behavior.

MELCOR assessment of sequential severe accident mitigation actions under SGTR accident

International Nuclear Information System (INIS)

Choi, Wonjun; Jeon, Joongoo; Kim, Nam Kyung; Kim, Sung Joong

2017-01-01

The representative example of the severe accident studies using the severe accident code is investigation of effectiveness of developed severe accident management (SAM) strategy considering the positive and adverse effects. In Korea, some numerical studies were performed to investigate the SAM strategy using various severe accident codes. Seo et.al performed validation of RCS depressurization strategy and investigated the effect of severe accident management guidance (SAMG) entry condition under small break loss of coolant accident (SBLOCA) without safety injection (SI), station blackout (SBO), and total loss of feed water (TLOFW) scenarios. The SGTR accident with the sequential mitigation actions according to the flow chart of SAMG was simulated by the MELCOR 1.8.6 code. Three scenariospreventing the RPV failure were investigated in terms of fission product release, hydrogen risk, and the containment pressure. Major conclusions can be summarized as follows: (1) According to the flow chart of SAMG, RPV failure can be prevented depending on the method of RCS depressurization. (2) To reduce the release of fission product during the injecting into SGs, a temporary opening of SDS before the injecting into SGs was suggested. These modified sequences of mitigation actions can reduce the release of fission product and the adverse effect of SDS.

Vaporization of low-volatile fission products under severe CANDU reactor accident conditions

International Nuclear Information System (INIS)

Lewis, B.J.; Corse, B.J.; Thompson, W.T.; Kaye, M.H.; Iglesias, F.C.; Elder, P.; Dickson, R.; Liu, Z.

1997-01-01

An analytical model has been developed to describe the release behaviour of low-volatile fission products from uranium dioxide fuel under severe reactor accident conditions. The effect of the oxygen potential on the chemical form and volatility of fission products is determined by Gibbs-energy minimization. The release kinetics are calculated according to the rate-controlling step of diffusional transport in the fuel matrix or fission product vaporization from the fuel surface. The effect of fuel volatilization (i.e., matrix stripping) on the release behaviour is also considered. The model has been compared to data from an out-of-pile annealing experiment performed in steam at the Chalk River Laboratories. (author)

Accident progression event tree analysis for postulated severe accidents at N Reactor

International Nuclear Information System (INIS)

Wyss, G.D.; Camp, A.L.; Miller, L.A.; Dingman, S.E.; Kunsman, D.M.; Medford, G.T.

1990-06-01

A Level II/III probabilistic risk assessment (PRA) has been performed for N Reactor, a Department of Energy (DOE) production reactor located on the Hanford reservation in Washington. The accident progression analysis documented in this report determines how core damage accidents identified in the Level I PRA progress from fuel damage to confinement response and potential releases the environment. The objectives of the study are to generate accident progression data for the Level II/III PRA source term model and to identify changes that could improve plant response under accident conditions. The scope of the analysis is comprehensive, excluding only sabotage and operator errors of commission. State-of-the-art methodology is employed based largely on the methods developed by Sandia for the US Nuclear Regulatory Commission in support of the NUREG-1150 study. The accident progression model allows complex interactions and dependencies between systems to be explicitly considered. Latin Hypecube sampling was used to assess the phenomenological and systemic uncertainties associated with the primary and confinement system responses to the core damage accident. The results of the analysis show that the N Reactor confinement concept provides significant radiological protection for most of the accident progression pathways studied

Acidente de trabalho, morte e fatalismo Work accident, death and fatalism

Directory of Open Access Journals (Sweden)

Izabel Cristina Ferreira Borsoi

2005-04-01

Full Text Available Este artigo se propõe discutir a atitude fatalista diante do acidente de trabalho e da morte. Toma como suporte empírico a representação que trabalhadores acidentados na construção civil constroem acerca daqueles eventos. Parte de um conjunto de entrevistas com seis trabalhadores que se encontravam afastados do trabalho por invalidez decorrente do acidente. A análise realizada busca mostrar que os indivíduos tendem a construir explicações e justificativas a partir de uma perspectiva fatalista de modo a poderem aceitar e conviver com o medo do acidente e da morte ou com a dor da perda. Argumenta também que a atitude fatalista, não pode se modificar apenas com a tomada de consciência, por parte dos trabalhadores, de que acidentes e mortes no trabalho estão relacionados a condições precárias de trabalho. Para modificarem suas atitudes, seria necessário, também, que experimentassem novas condições de vida e trabalho, podendo, assim, construir uma nova concepção de mundo e de vida.This article proposes a discussion about the fatalistic posture adopted when a worker faces work accidents and death. It has its empirical support on the representation which injured construction workers create about these events. The study was based on interviews made with six workers who were unable to return to work due to the disability caused by accidents. The accomplished analysis intends to show that the individuals create explanations and justifications based on a fatalistic perspective. This way of thinking enables them to accept and to live with the fear of accidents and death, or with the pain caused by a loss. It also argues that the fatalistic attitude cannot be modified only by understanding that accidents and deaths that happen at the work environment are related to its precarious conditions. In order to change this attitude, it would be necessary to experience new conditions of life and work, so that the workers would be able to create

Transient debris freezing and potential wall melting during a severe reactivity initiated accident experiment

International Nuclear Information System (INIS)

El-Genk, M.S.; Moore, R.L.

1981-01-01

It is important to light water reactor (LWR) safety analysis to understand the transient freezing of molten core debris on cold structures following a hypothetical core meltdown accident. The purpose of this paper is to (a) present the results of a severe reactivity initiated accident (RIA) in-pile experiment with regard to molten debris distribution and freezing following test fuel rod failure, (b) analyze the transient freezing of molten debris (primarily a mixture of UO/sub 2/ fuel and Zircaloy cladding) deposited on the inner surface of the test shroud wall upon rod failure, and (c) assess the potential for wall melting upon being contacted by the molten debris. 26 refs

Impact of fission gas on irradiated PWR fuel behaviour at extended burnup under RIA conditions

International Nuclear Information System (INIS)

Lemoine, F.; Schmitz, F.

1996-01-01

With the world-wide trend to increase the fuel burnup at discharge of the LWRs, the reliability of high burnup fuel must be proven, including its behaviour under energetic transient conditions, and in particular during RIAs. Specific aspects of irradiated fuel result from the increasing retention of gaseous and volatile fission products with burnup. The potential for swelling and transient expansion work under rapid heating conditions characterizes the high burnup fuel behaviour by comparison to fresh fuel. This effect is resulting from the steadily increasing amount of gaseous and volatile fission products retained inside the fuel structure. An attempt is presented to quantify the gas behaviour which is motivated by the results from the global tests both in CABRI and in NSRR. A coherent understanding of specific results, either transient release or post transient residual retention has been reached. The early failure of REP Na1 with consideration given to the satisfactory behaviour of the father rod of the test pin at the end of the irradiation (under load follow conditions) is to be explained both by the transient loading from gas driven fuel swelling and from the reduced clad resistance due to hydriding. (R.P.)

Determination of gamma-ray exposure rate from short-lived fission products under criticality accident conditions

International Nuclear Information System (INIS)

Yanagisawa, Hiroshi; Ohno, Akio; Aizawa, Eijyu

2002-01-01

For the assessment of γ-ray doses from short-lived fission products (FPs) under criticality accident conditions, γ-ray exposure rates varying with time were experimentally determined in the Transient Experiment Critical Facility (TRACY). The data were obtained by reactivity insertion in the range of 1.50 to 2.93$. It was clarified from the experiments that the contribution of γ-ray from short-lived FPs to total exposure during the experiments was evaluated to be 15 to 17%. Hence, the contribution cannot be neglected for the assessment of γ-ray doses under criticality accident conditions. Computational analyses also indicated that γ-ray exposure rates from short-lived FPs calculated with the Monte Carlo code, MCNP4B, and photon sources based on the latest FP decay data, the JENDL FP Decay Data File 2000, well agreed with the experimental results. The exposure rates were, however, extremely underestimated when the photon sources were obtained by the ORIGEN2 code. The underestimation is due to lack of energy-dependent photon emission data for major short-lived FP nuclides in the photon database attached to the ORIGEN2 code. It was also confirmed that the underestimation arose in 1,000 or less of time lapse after an initial power burst. (author)

Mechanisms of damage to the oxide layer of cladding of fuel rods under accident conditions like RI

International Nuclear Information System (INIS)

Busser, Vincent

2009-01-01

During reactivity initiated accident, the importance of cladding tube oxidation on its thermomechanical behavior has been investigated. After RIA tests in experimental reactors oxide damage including radial cracking and spallation of the outer oxide layer has been evidenced. This work aims at better understanding the key mechanisms controlling these phenomena. Laboratory air-oxidation of Zircaloy-4 cladding tubes has been performed at 470 C. SEM micrographs show that radial cracks are initiated from the outer surface of the oxide layer and propagated radially towards the oxide-metal interface. A model predicting the stress evolution within the oxide and the depth of crack has been developed and validated on literature tests and tests of this study. Ring compression tests were used for the experimental study of the oxide degradation under mechanical loading. Experimental data revealed three mechanisms: densification of the radial crack network, propagation of these radial cracks, branching and spallation of oxide fragments. The influence of the circumferential cracks, periodically distributed in the oxide layer, on the stress distribution in oxide fragments has been analysed using finite element modelling. The determining influence of these cracks on the maximum stress oxide fragments has been demonstrated. (author)

Characterization and chemistry of fission products released from LWR fuel under accident conditions

International Nuclear Information System (INIS)

Norwood, K.S.; Collins, J.L.; Osborne, M.F.; Lorenz, R.A.; Wichner, R.P.

1984-01-01

Segments from commercial LWR fuel rods have been tested at temperatures between 1400 and 2000 0 C in a flowing steam-helium atmosphere to simulate severe accident conditions. The primary goals of the tests were to determine the rate of fission product release and to characterize the chemical behavior. This paper is concerned primarily with the identification and chemical behavior of the released fission products with emphasis on antimony, cesium, iodine, and silver. The iodine appeared to behave primarily as cesium iodide and the antimony and silver as elements, while cesium behavior was much more complex. 17 refs., 7 figs., 1 tab

Chemistry of fission product iodine under nuclear reactor accident conditions

International Nuclear Information System (INIS)

Malinauskas, A.P.; Bell, J.T.

1986-01-01

The radioisotopes of iodine are generally acknowledged to be the species whose release into the biosphere as a result of a nuclear reactor accident is of the greatest concern. In the course of its release, the fission product is subjected to differing chemical environments; these can alter the physicochemical form of the fission product and thus modify the manner and extent to which release occurs. Both the chemical environments which are characteristic of reactor accidents and their effect in determining physical and chemical form of fission product iodine have been studied extensively, and are reviewed in this report. 76 refs

Accident management information needs

International Nuclear Information System (INIS)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R.

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs

Accident management information needs

Energy Technology Data Exchange (ETDEWEB)

Hanson, D.J.; Ward, L.W.; Nelson, W.R.; Meyer, O.R. (EG and G Idaho, Inc., Idaho Falls, ID (USA))

1990-04-01

In support of the US Nuclear Regulatory Commission (NRC) Accident Management Research Program, a methodology has been developed for identifying the plant information needs necessary for personnel involved in the management of an accident to diagnose that an accident is in progress, select and implement strategies to prevent or mitigate the accident, and monitor the effectiveness of these strategies. This report describes the methodology and presents an application of this methodology to a Pressurized Water Reactor (PWR) with a large dry containment. A risk-important severe accident sequence for a PWR is used to examine the capability of the existing measurements to supply the necessary information. The method includes an assessment of the effects of the sequence on the measurement availability including the effects of environmental conditions. The information needs and capabilities identified using this approach are also intended to form the basis for more comprehensive information needs assessment performed during the analyses and development of specific strategies for use in accident management prevention and mitigation. 3 refs., 16 figs., 7 tabs.

NPP physical protection and information security as necessary conditions for reducing nuclear and radiation accident risks

International Nuclear Information System (INIS)

Pogosov, O.Yu.; Derevyanko, O.V.

2017-01-01

The paper focuses on the fact that nuclear failures and incidents can lead to radioactive contamination of NPP premises. Nuclear and radiation hazard may be caused by malefactors in technological processes when applying computers or inadequate control in case of insufficient level of information security.The researchers performed analysis of factors for reducing risks of nuclear and radiation accidents at NPPs considering specific conditions related to information security of NPP physical protection systems. The paper considers connection of heterogeneous factors that may increase the risk of NPP accidents, possibilities and ways to improve adequate modelling of security of information with limited access directly related to the functioning of automated set of engineering and technical means for NPP physical protection. Within the overall Hutchinson formalization, it is proposed to include additional functional dependencies on indicators specific for NPPs into analysis algorithms.

HISTÓRIAS DE RETIRANTES: RUÍNAS LITERÁRIAS NO CINEMA

Directory of Open Access Journals (Sweden)

Elisabete Alfeld Rodrigues

2009-06-01

Full Text Available Em O caminho das nuvens, Vicente Amorim conta a história da retirada de uma família do interior nordestino para a região sudeste. Uma história que já foi muitas vezes contada, por exemplo, em Vidas Secas: primeiro, na literatura, por Graciliano Ramos e, depois, no cinema, por Nélson Pereira dos Santos. Na retirada contada por Amorim, a migração não ocorre pelos passos na aridez do sertão; ela acontece por bicicletas nas rodovias, estradas e pequenas cidades que a família – pai, mãe e cinco filhos – percorre para chegar à cidade do Rio de Janeiro. A família se desloca da Paraíba em busca de um emprego de mil reais por mês que só pode ser encontrado no sudeste do Brasil – este motivo desencadeador parte de uma história factual. O filme é uma releitura que resgata a literatura, o cinema e a história factual promovendo uma relação dialógica construída por fragmentos das várias histórias.

Accidents (FARS) (National)

Data.gov (United States)

Department of Transportation — Accident - (1975-current): This data file (NTAD) contains information about crash characteristics and environmental conditions at the time of the crash. There is one...

A radiation condition in some regions with more pronounced effect of the Chernobyl accident

International Nuclear Information System (INIS)

Ivanov, I.V.; Ivanov, I.M.

1993-01-01

The radioecological condition of the Devin region situated in the Rodopes mountain (Bulgaria) has been investigated for the period October 1992 - March 1993. It is believed that the Rodopes were more significantly affected by the Chernobyl accident in comparison with other regions of Bulgaria. Some regions near Kozloduy NPP have been chosen for comparing, for which there are more detailed investigations of the anthropogenic radiation effects. Analysis of the background radiation is made, specific soil and water samples are tested. The alterations in the radiation conditions of the Devin region are analysed. Some conclusions and predictions for the trends in further alterations of the background radiation are made. As a result a draft regional program for environment protection reclamation is prepared. (V.K.)

10 CFR 50.67 - Accident source term.

Science.gov (United States)

2010-01-01

... Conditions of Licenses and Construction Permits § 50.67 Accident source term. (a) Applicability. The... 10 Energy 1 2010-01-01 2010-01-01 false Accident source term. 50.67 Section 50.67 Energy NUCLEAR... to January 10, 1997, who seek to revise the current accident source term used in their design basis...

Clinical significance of the dynamic changes of serum IGF-1 levels in patients with acute cerebro-vascular accident

International Nuclear Information System (INIS)

Chen Yujuan; Liu Xueyuan; Bian Weihong; Du Xinlu; Yang Hongyan

2006-01-01

Objective: To investigate the dynamic changes of serum insulin-like growth factor-1 (IGF-1) levels in patients with acute cerebrovascular accident. Methods: Serum IGF-1 levels were determined with RIA in 40 patients with cerebral infarction, 20 patients with lacunar infarcts and 40 patients with cerebral haemorrhage within 3days after onset and on d14 as well as in 30 controls. Results: The serum IGF-1 levels in patients with cerebral vascular accidents were significantly lower than those in controls (P 0.05). Conclusion: Serum levels of IGF-1 dropped markedly during the acute stage after cerebrovascular accident and the magnitude might reflect the severity of the event, IGF-1 might be capable of crossing the blood-brain barrier after cerebrovascular accident and providing some protection against nerve injury, this fact might be of potential clinical applicability. (authors)

[Hypoglycemia as a cause of traffic accidents].

Science.gov (United States)

Metter, D

1989-05-01

Hypoglycemia is the most important subsidiary effect of insulin therapy, where traffic medicine is concerned. A study has been made of 8 motor car drivers each dependent on insulin and involved in road accidents. The evidence was issued during the trial. The questions set out to prove if there was a state of hypoglycemia and if the afflicted could have foreseen this condition. In 5 cases the driving conduct before the accidents was evident in cordinatory disturbances, which resulted in sinuous driving. The accidents all happened in every-day traffic conditions, namely counter traffic (3), front-end collision (3) and through disregard of right-of-way at cross-roads (1). A further accident was conditioned by an alcoholic state while parking in a car-park. The disturbances in consciousness conditioned by hypoglycemia occurred without warning. In 3 cases the predictability (in legal terms Actio libera in causa) had to be conceded, because the drivers had set out on their routes despite warning signals or insufficient intake of nourishment beforehand.

Investigation program on PWR-steel-containment behavior under accident conditions

International Nuclear Information System (INIS)

Krieg, R.; Eberle, F.; Goeller, B.; Gulden, W.; Kadlec, J.; Messemer, G.; Mueller, S.; Wolf, E.

1983-10-01

This report is a first documentation of the KfK/PNS activities and plans to investigate the behaviour of steel containments under accident conditions. The investigations will deal with a free standing spherical containment shell built for the latest type of a German pressurized water reactor. The diameter of the containment shell is 56 m. The minimum wall thickness is 38 mm. The material used is the ferritic steel 15MnNi63. According to the actual planning the program is concerned with four different problems which are beyond the common design and licensing practice: Containment behavior under quasi-static pressure increase up to containment failure. Containment behavior under high transient pressures. Containment oscillations due to earthquake loadings; consideration of shell imperfections. Containment buckling due to earthquake loadings. The investigation program consists of both theoretical and experimental activities including membrane tests allowing for very high plastic strains and oscillation tests with a thin-walled, high-accurate spherical shell. (orig.) [de

Computation of reactor control rod drop time under accident conditions

International Nuclear Information System (INIS)

Dou Yikang; Yao Weida; Yang Renan; Jiang Nanyan

1998-01-01

The computational method of reactor control rod drop time under accident conditions lies mainly in establishing forced vibration equations for the components under action of outside forces on control rod driven line and motion equation for the control rod moving in vertical direction. The above two kinds of equations are connected by considering the impact effects between control rod and its outside components. Finite difference method is adopted to make discretization of the vibration equations and Wilson-θ method is applied to deal with the time history problem. The non-linearity caused by impact is iteratively treated with modified Newton method. Some experimental results are used to validate the validity and reliability of the computational method. Theoretical and experimental testing problems show that the computer program based on the computational method is applicable and reliable. The program can act as an effective tool of design by analysis and safety analysis for the relevant components

Experimental data report for test TS-3 Reactivity Initiated Accident test in the NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Fujishiro, Toshio; Kobayashi, Shinsho; Yamahara, Takeshi; Sukegawa, Tomohide; Kikuchi, Teruo; Sobajima, Makoto.

1993-09-01

This report presents experimental data for Test TS-3 which was the third test in a series of Reactivity Initiated Accident (RIA) tests using pre-irradiated BWR fuel rods, performed in the Nuclear Safety Research Reactor (NSRR) in September, 1990. Test fuel rod used in the Test TS-3 was a short-sized BWR (7 x 7) type rod which was re-fabricated from a commercial rod irradiated in the Tsuruga Unit 1 power reactor of Japan Atomic Power Co. The fuel had an initial enrichment of 2.79 % and a burnup of 26 Gwd/tU. A pulse irradiation of the test fuel rod was performed under a cooling condition of stagnant water at atmospheric pressure and at ambient temperature which simulated a BWR's cold start-up RIA event. The energy deposition of the fuel rod in this test was evaluated to be 94 ± 4 cal/g · fuel (88 ± 4 cal/g · fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, transient behavior of the test rod during the pulse irradiation, and results of pre-pulse and post-pulse irradiation examinations are described in this report. (author)

Early results from an experimental program to determine the behavior of containment piping penetration bellows subjected to severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1994-01-01

Containment piping penetration bellows are an integral part of the pressure boundary in steel containments in the United States (US). Their purpose is to minimize loading on the containment shell caused by differential movement between the piping and the containment. This differential movement is typically caused by thermal gradients generated during startup and shutdown of the reactor, but can be caused by earthquake, a loss-of-coolant accident (LOCA), or ''severe'' accidents. In the event of a severe accident, the bellows would be subjected to pressure, temperature, and deflection well beyond the design basis. Most bellows are installed such that they would be subjected to elevated internal pressure, elevated temperature, axial compression, and lateral deflection during a severe accident. A few bellows would be subjected to external pressure and axial elongation, as well as elevated temperature and lateral deflection. The purpose of this experimental program is to examine the potential for leakage of containment bellows during a severe accident. The test series subjects bellows to various levels and combinations of internal pressure, elevated temperature, axial compression or elongation, and lateral deformation. The experiments are being conducted in two parts. For Part 1, all bellows specimens are tested in ''like-new'' condition, without regard for the possible degrading effect of corrosion that has been observed in some containment piping bellows in the US Part I testing, which included 13 bellows tests, has been completed. The second part of the experimental program, in which bellows are subjected to simulated corrosive environments prior to testing, has just just begun. The Part I experiments have shown that bellows in ''like-new'' condition can withstand elevated temperatures and pressures along with large deformations before leaking. In most cases, the like-new bellows were fully compressed without developing any leakage

Instrumentation for the follow-up of severe accidents

International Nuclear Information System (INIS)

Munoz Sanchez, A.; Nino Perote, R.

2000-01-01

During severe accidents, it is foreseeable that the instrumentation installed in a plant is subjected to conditions which are more hostile than those for which the instrumentation was designed and qualified. Moreover, new, specific instrumentation is required to monitor variables which have not been considered until now, and to control systems which lessen the consequences of severe accidents. Both existing instrumentation used to monitor critical functions in design basis accident conditions and additional instrumentation which provides the information necessary to control and mitigate the consequences of severe accidents, have to be designed to withstand such conditions, especially in terms of measurements range, functional characteristics and qualification to withstand pressure and temperature loads resulting from steam explosion, hydrogen combustion/explosion and high levels of radiation over long periods of time. (Author)

Instrumentation Performance during the TMI-2 Accident

International Nuclear Information System (INIS)

Rempe, Joy L.; Knudson, Darrell L.

2013-06-01

The accident at the Three Mile Island Unit 2 (TMI- 2) reactor provided a unique opportunity to evaluate sensors exposed to severe accident conditions. Conditions associated with the release of coolant and the hydrogen burn that occurred during this accident exposed instrumentation to harsh conditions, including direct radiation, radioactive contamination, and high humidity with elevated temperatures and pressures. As part of a program initiated by the Department of Energy Office of Nuclear Energy (DOE-NE), a review was completed to gain insights from prior TMI-2 sensor survivability and data qualification efforts. This new effort focused upon a set of sensors that provided critical data to TMI-2 operators for assessing the condition of the plant and the effects of mitigating actions taken by these operators. In addition, the effort considered sensors providing data required for subsequent accident simulations. Over 100 references related to instrumentation performance and post-accident evaluations of TMI-2 sensors and measurements were reviewed. Insights gained from this review are summarized within this paper. As noted within this paper, several techniques were invoked in the TMI-2 post-accident program to evaluate sensor survivability status and data qualification, including comparisons with data from other sensors, analytical calculations, laboratory testing, and comparisons with sensors subjected to similar conditions in large-scale integral tests and with sensors that were similar in design but more easily removed from the TMI-2 plant for evaluations. Conclusions from this review provide important insights related to sensor survivability and enhancement options for improving sensor performance. In addition, this paper provides recommendations related to sensor survivability and the data evaluation process that could be implemented in upcoming Fukushima Daiichi recovery efforts. (authors)

Hydrogen generation, distribution and combustion under severe LWR accident conditions: a state-of-technology report

International Nuclear Information System (INIS)

Postma, A.K.; Hilliard, R.K.

1983-03-01

This report reviews the current state of technology regarding hydrogen safety issues in light water reactor plants. Topics considered in this report include hydrogen generation, distribution in containment, and combustion characteristics. A companion report addresses hydrogen control. The objectives of the study were to identify the key safety issues related to hydrogen produced under severe accident conditions, to describe the state of technology for each issue, and to point out ongoing programs aimed at resolving the open issues

Study On Safety Analysis Of PWR Reactor Core In Transient And Severe Accident Conditions

International Nuclear Information System (INIS)

Le Dai Dien; Hoang Minh Giang; Nguyen Thi Thanh Thuy; Nguyen Thi Tu Oanh; Le Thi Thu; Pham Tuan Nam; Tran Van Trung; Le Van Hong; Vo Thi Huong

2014-01-01

The cooperation research project on the Study on Safety Analysis of PWR Reactor Core in Transient and Severe Accident Conditions between Institute for Nuclear Science and Technology (INST), VINATOM and Korean Atomic Energy Research Institute (KAERI), Korea has been setup to strengthen the capability of researches in nuclear safety not only in mastering the methods and computer codes, but also in qualifying of young researchers in the field of nuclear safety analysis. Through the studies on the using of thermal hydraulics computer codes like RELAP5, COBRA, FLUENT and CFX the thermal hydraulics research group has made progress in the research including problems for safety analysis of APR1400 nuclear reactor, PIRT methodologies and sub-channel analysis. The study of severe accidents has been started by using MELCOR in collaboration with KAERI experts and the training on the fundamental phenomena occurred in postulated severe accident. For Vietnam side, VVER-1000 nuclear reactor is also intensively studied. The design of core catcher, reactor containment and severe accident management are the main tasks concerning VVER technology. The research results are presented in the 9 th National Conference on Mechanics, Ha Noi, December 8-9, 2012, the 10 th National Conference on Nuclear Science and Technology, Vung Tau, August 14-15, 2013, as well as published in the journal of Nuclear Science and Technology, Vietnam Nuclear Society and other journals. The skills and experience from using computer codes like RELAP5, MELCOR, ANSYS and COBRA in nuclear safety analysis are improved with the nuclear reactors APR1400, Westinghouse 4 loop PWR and especially the VVER-1000 chosen for the specific studies. During cooperation research project, man power and capability of Nuclear Safety center of INST have been strengthen. Three masters were graduated, 2 researchers are engaging in Ph.D course at Hanoi University of Science and Technology and University of Science and Technology, Korea

Accidents - Chernobyl accident

International Nuclear Information System (INIS)

2004-01-01

This file is devoted to the Chernobyl accident. It is divided in four parts. The first part concerns the accident itself and its technical management. The second part is relative to the radiation doses and the different contaminations. The third part reports the sanitary effects, the determinists ones and the stochastic ones. The fourth and last part relates the consequences for the other European countries with the case of France. Through the different parts a point is tackled with the measures taken after the accident by the other countries to manage an accident, the cooperation between the different countries and the groups of research and studies about the reactors safety, and also with the international medical cooperation, specially for the children, everything in relation with the Chernobyl accident. (N.C.)

Assessment of radiation doses in normal operation, upset accident conditions at the Olkiluoto nuclear waste facility

International Nuclear Information System (INIS)

Rossi, J.; Raiko, H.; Suolanen, V.

2009-09-01

Radiation doses for workers of the facility, for inhabitants in the environment and for terrestrial ecosystem possibly caused by the encapsulation and disposal facility to be built at Olkiluoto during its operation were considered in the study. The study covers both the normal operation of the plant and some hypothetical incidents and accidents. Release through the ventilation stack is assumed to be filtered both in normal operation and in hypothetical abnormal fault and accident cases. Calculation of the offsite doses from normal operation is based on the hypothesis that on average one fuel pin per 100 fuel bundles for all batches of spent fuel transported to the encapsulation facility is leaking. The release magnitude in incidents and accidents is based on the event chains, which lead to loss of fuel pin tightness followed by a discharge of radionuclides into the handling space and to some degree to the atmosphere through the ventilation stack equipped with redundant filters. The critical group is conservatively assumed to live at the distance of 200 meters from the encapsulation and disposal plant and thus it will receive the largest doses in most dispersion conditions. The dose value to a member of the critical group was calculated on the basis of the weather data in such a way that greater dose than obtained here is caused only in 0.5 percent of dispersion conditions. The results obtained indicate that during normal operation the doses to workers remain small and the dose to the member of the critical group is less than 0,001 mSv per year. In the case of hypothetical fault and accident releases the offsite doses do not exceed either the limit values set by the safety authority. The highest dose rates to the reference organisms of the terrestrial ecosystem with conservative assumptions from the largest release were estimated to be of the order of 100 μ Gy/h at the distance of 200 m. As a chronic exposure this dose rate is expected to bring up detrimental

Analysis of reactivity accidents in PWR'S

International Nuclear Information System (INIS)

Camous, F.; Chesnel, A.

1989-12-01

This note describes the French strategy which has consisted, firstly, in examining all the accidents presented in the PWR unit safety reports in order to determine for each parameter the impact on accident consequences of varying the parameter considered, secondly in analyzing the provisions taken into account to restrict variation of this parameter to within an acceptable range and thirdly, in checking that the reliability of these provisions is compatible with the potential consequences of transgression of the authorized limits. Taking into consideration violations of technical operating specifications and/or non-observance of operating procedures, equipment failures, and partial or total unavailability of safety systems, these studies have shown that fuel mechanical strength limits can be reached but that the probability of occurrence of the corresponding events places them in the residual risk field and that it must, in fact, be remembered that there is a wide margin between the design basis accidents and accidents resulting in fuel destruction. However, during the coming year, we still have to analyze scenarios dealing with cumulated events or incidents leading to a reactivity accident. This program will be mainly concerned with the impact of the cases examined relating to dilution incidents under normal operating conditions or accident operating conditions

Psychical and social effects related to post-accident situations: some training of Chernobyl accident

International Nuclear Information System (INIS)

Lochand, J.

1995-01-01

Some preliminary considerations on the psychic and societal dimensions related to post-accident situations connected to large scale and heavy land contamination are presented. This is done with the objective of exploring the role that these dimensions could play in the elaboration of new radiological protection principles and concepts in order to restore confidence among affected populations after a nuclear accident. It is important to facilitate the return to normal or, at least, acceptable living conditions, as soon as reasonably achievable, and to prevent the possible emergence of a post-accident crisis. A scheme is proposed for understanding the dynamics of the various phases after an accident, taking into account the collective response to the consequences as well as, the response to the countermeasures. (Author)

Behavior of U3Si2 Fuel and FeCrAl Cladding under Normal Operating and Accident Reactor Conditions

International Nuclear Information System (INIS)

Gamble, Kyle Allan Lawrence; Hales, Jason Dean; Barani, Tommaso; Pizzocri, Davide; Pastore, Giovanni

2016-01-01

As part of the Department of Energy's Nuclear Energy Advanced Modeling and Simulation program, an Accident Tolerant Fuel High Impact Problem was initiated at the beginning of fiscal year 2015 to investigate the behavior of \\usi~fuel and iron-chromium-aluminum (FeCrAl) claddings under normal operating and accident reactor conditions. The High Impact Problem was created in response to the United States Department of Energy's renewed interest in accident tolerant materials after the events that occurred at the Fukushima Daiichi Nuclear Power Plant in 2011. The High Impact Problem is a multinational laboratory and university collaborative research effort between Idaho National Laboratory, Los Alamos National Laboratory, Argonne National Laboratory, and the University of Tennessee, Knoxville. This report primarily focuses on the engineering scale research in fiscal year 2016 with brief summaries of the lower length scale developments in the areas of density functional theory, cluster dynamics, rate theory, and phase field being presented.

A risk-based evaluation of LMFBR containment response under core disruptive accident conditions

International Nuclear Information System (INIS)

Hartung, J.; Berk, S.

1978-01-01

Probabilistic risk methodology is utilized to evaluate the failure modes and effects of LMFBR containment systems under Core Disruptive Accident (CDA) conditions. First, the potential causes of LMFBR containment failure under CDA conditions are discussed and categorized. Then, a simple scoping-type risk assessment of a reference design is presented to help place these potential causes of failure in perspective. The highest risk containment failure modes are identified for the reference design, and several design and research and development options which appear capable of reducing these risks are discussed. The degree to which large LMFBR containment systems must mitigate the consequences of CDA's to achieve a level of risk (for LMFBR's) comparable to the already very low risk of contemporary LWR's is explored. Based on the results of this evaluation, several suggestions are offered concerning CDA-related design goals and research and development priorities for large LMFBR's. (author)

Report of a consultants meeting on accidents during shutdown conditions for WWER nuclear power plants. Extrabudgetary programme on the safety of WWER NPPs

International Nuclear Information System (INIS)

1996-07-01

The main objectives of the meeting were to exchange information on the operational occurrences, studies performed and countermeasures taken for the accidents during shutdown for WWERs, and to define the necessity and directions of the further activities which may promote the improvement of WWER safety under shutdown conditions. The consultants have discussed some aspects concerning vulnerability of safety functions during shutdown conditions, several steps required to performed accident analysis and selected operational aspects for shutdown conditions. The discussion was supported by an evaluation of selected operational occurrences. The consultants have agreed that the discussion during the meeting in major parts is relevant to all the WWER designs (i.e. WWER-1000, WWER-440/213 and WWER-440/230). As for the plant conditions, the consultants have agreed to bound the discussion mainly by the cold shutdown and refuelling modes. Refs, figs, tabs

Aspects Concerning The Rules And The Investigation Of Traffic Accidents As Work Accidents

Science.gov (United States)

Tarnu, Lucian Ioan

2015-07-01

When Romania joined the European Union, it was imposed that the Romanian legislation in the field of the security and health at work be in line with the European one. The concept of health as it is defined by the International Body of Health, refers to a good physical, mental and social condition. The improvement of the activity of preventing the traffic accidents as work accidents must have as basis the correct and accurate evaluation of risks of getting injured. The goal of the activity of prevention and protection is to ensure the best working conditions, the prevention of accidents and occupational diseases and the adjustment to the scientific and technological progress. In the road transport sector, as in any other sector, it is very important to pay attention to working conditions to ensure a workforce motivated and well qualified. Some features make it a more difficult sector risk management than other sectors. However, if one takes into account how it works in practice this sector and the characteristics of drivers and how they work routinely, risks, dangers and threats can be managed efficiently and with great success.

Factors contributing to young moped rider accidents in Denmark

DEFF Research Database (Denmark)

Møller, Mette; Haustein, Sonja

2016-01-01

Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers...... was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number...... of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved...

PWR-related integral safety experiments in the PKL 111 test facility SBLOCA under beyond-design-basis accident conditions

Energy Technology Data Exchange (ETDEWEB)

Weber, P.; Umminger, K.J.; Schoen, B. [Siemens AG Power Generation Group (KWU), Erlangen (France)

1995-09-01

The thermal hydraulic behavior of a PWR during beyond-design-basis accident scenarios is of vital interest for the verification and optimization of accident management procedures. Within the scope of the German reactor safety research program experiments were performed in the volumetrically scaled PKL 111 test facility by Siemens/KWU. This highly instrumented test rig simulates a KWU-design PWR (1300 MWe). In particular, the latest tests performed related to a SBLOCA with additional system failures, e.g. nitrogen entering the primary system. In the case of a SBLOCA, it is the goal of the operator to put the plant in a condition where the decay heat can be removed first using the low pressure emergency core cooling system and then the residual heat removal system. The experimental investigation presented assumed the following beyond-design-basis accident conditions: 0.5% break in a cold leg, 2 of 4 steam generators (SGs) isolated on the secondary side (feedwater- and steam line-valves closed), filled with steam on the primary side, cooldown of the primary system using the remaining two steam generators, high pressure injection system only in the two loops with intact steam generators, if possible no operator actions to reach the conditions for residual heat removal system activation. Furthermore, it was postulated that 2 of the 4 hot leg accumulators had a reduced initial water inventory (increased nitrogen inventory), allowing nitrogen to enter the primary system at a pressure of 15 bar and nearly preventing the heat transfer in the SGs ({open_quotes}passivating{close_quotes} U-tubes). Due to this the heat transfer regime in the intact steam generators changed remarkably. The primary system showed self-regulating system effects and heat transfer improved again (reflux-condenser mode in the U-tube inlet region).

Modelling Reactivity-Initiated-Accident Experiments With Falcon And SCANAIR: A Comparison Exercise

International Nuclear Information System (INIS)

Romano, A.; Wallin, H.; Zimmermann, M.A.

2005-01-01

A critical assessment is made of the state-of-the-art fuel performance code FALCON in the context of selected Reactivity Initiated Accident (RIA) experiments from the CABRI REP Na series, and contrasts its predictions against those of the extensively benchmarked SCANAIR (Version 3.2) code. The thermal fields in the fuel and cladding, the clad mechanical deformation, and the Fission Gas Release (FGR) are adopted as 'Figures of Merit' by which to judge code performance. Particular attention is paid to the importance of fission-gas-induced clad deformation (which is modelled in SCANAIR, but not in FALCON), relative to that driven by the fuel thermal expansion (which is modelled by both codes). The thermal fields calculated by the codes are in good agreement with each other, especially during the initial stages of the transients --- the adiabatic phase. Larger discrepancies are observed at later times, and are due to the different models applied to calculate the gap conductance. FALCON predicts clad permanent deformations at the end of the transients with a maximum deviation from the experimental measurements of about 20%. Generally, the code always tends to underpredict the measurements. SCANAIR performs similarly, but grossly overpredicts the permanent clad strain for the case involving a very energetic pulse. The fission-gas-driven clad deformation is only relevant for very fast pulse energy injection cases, which are not prototypical of the RIA transients expected in PWRs. The FGR models in FALCON do not capture the mechanism of 'burst-release' in the RIA transients, having been developed for steady-state irradiation conditions. This also explains why they performed poorly when applied to the fast-transient cases analyzed here. In contrast, the FGR results from SCANAIR are in satisfactory agreement with the experimental results. (author)

Reactivity estimation during a reactivity-initiated accident using the extended Kalman filter

International Nuclear Information System (INIS)

Busquim e Silva, R.; Marques, A.L.F.; Cruz, J.J.; Shirvan, K.; Kazimi, M.S.

2015-01-01

Highlights: • The EKF is modeled using sophisticate strategies to make the algorithm robust and accurate. • For a supercritical reactor under RIA, the EKF presents better results compared to IPK method independent of magnitude of the noise loads. • A sensitivity for five distinct carry-over effects indicates that the EKF is less sensitive to the different set of noise. • Although the P3D/R5 simulates the reactivity using a spatial kinetics method, the use of PKRE to model the EKF provides accurate results. • The reactivity’s standard deviation is higher for the IKF method. • Under HZP (slow power response) the IPK reactivity varies widely from positive to negative values (add extra difficulty to controlling the supercritical reactor): the EKF method does not have similar behavior under the same conditions (better controlling the operation). - Abstract: This study implements the extended Kalman filter (EKF) to estimate the nuclear reactor reactivity behavior under a reactivity-initiated accident (RIA). A coupled neutronics/thermal hydraulics code PARCS/RELAP5 (P3D/R5) simulates a control rod assembly ejection (CRE) on a traditional 2272 MWt PWR to generate the reactor power profile. A MATLAB script adds random noise to the simulated reactor power. For comparison, the inverse point kinetics (IPK) deterministic method is also implemented. Three different cases of CRE are simulated and the EKF, IPK and the P3D/R5 reactivity are compared. It was found that the EKF method presents better results compared to the IPK method. Furthermore, under a RIA due to small reactivity insertion and slow power response, the IPK reactivity varies widely from positive to negative, which may add extra difficulty to the task of controlling a supercritical reactor. This feature is also confirmed by a sensitivity analysis for five different noise loads and three distinct noise measurements standard deviations (SD)

Severe accident testing of electrical penetration assemblies

International Nuclear Information System (INIS)

Clauss, D.B.

1989-11-01

This report describes the results of tests conducted on three different designs of full-size electrical penetration assemblies (EPAs) that are used in the containment buildings of nuclear power plants. The objective of the tests was to evaluate the behavior of the EPAs under simulated severe accident conditions using steam at elevated temperature and pressure. Leakage, temperature, and cable insulation resistance were monitored throughout the tests. Nuclear-qualified EPAs were produced from D. G. O'Brien, Westinghouse, and Conax. Severe-accident-sequence analysis was used to generate the severe accident conditions (SAC) for a large dry pressurized-water reactor (PWR), a boiling-water reactor (BWR) Mark I drywell, and a BWR Mark III wetwell. Based on a survey conducted by Sandia, each EPA was matched with the severe accident conditions for a specific reactor type. This included the type of containment that a particular EPA design was used in most frequently. Thus, the D. G. O'Brien EPA was chosen for the PWR SAC test, the Westinghouse was chosen for the Mark III test, and the Conax was chosen for the Mark I test. The EPAs were radiation and thermal aged to simulate the effects of a 40-year service life and loss-of-coolant accident (LOCA) before the SAC tests were conducted. The design, test preparations, conduct of the severe accident test, experimental results, posttest observations, and conclusions about the integrity and electrical performance of each EPA tested in this program are described in this report. In general, the leak integrity of the EPAs tested in this program was not compromised by severe accident loads. However, there was significant degradation in the insulation resistance of the cables, which could affect the electrical performance of equipment and devices inside containment at some point during the progression of a severe accident. 10 refs., 165 figs., 16 tabs

Tools to support important technical decisions during accident conditions

International Nuclear Information System (INIS)

Tenschert, J.; Bergiers, C.

2008-01-01

To handle design basis and beyond design basis accidents with intact reactor core, Nuclear Power Plants are using Emergency Operating Procedures (EOP) that they may have developed based on the generic Westinghouse Emergency Response Guidelines. Even though the EOPs are very directive, some questions are left to external support, i.e. to a team of persons constituting the so-called Technical Support Center (TSC). The Pressurized Water Reactor Owner Group (PWROG, previously Westinghouse Owner Group, WOG) has developed a TSC manual to support this group in their decision making process. Because of the specific and particular design of the Beznau NPP (KKB) Safety Systems, development of a plant-specific TSC manual required a lot of additions compared to the generic material. This plant-specific TSC manual is a helpful tool for the Site Emergency Director (SED) of the KKB to better evaluate issues and potential concerns arising while executing the EOPs. The majority of considered issues are relevant for beyond design basis accidents and external events. (orig.)

ENSINO DE HISTÓRIA E MEMÓRIA SOCIAL: A ARGUMENTAÇÃO COMO POSSIBILIDADE PEDAGÓGICA PARA A HISTÓRIA ENSINADA

Directory of Open Access Journals (Sweden)

Patricia Bastos de Azevedo

2010-12-01

Full Text Available Este texto é fruto da pesquisa desenvolvida no mestrado em Educação, no período de 2000 a 2003, na Universidade Federal Fluminense. Buscou-se identificar como os elementos história e memória se constituem no espaço da sala de aula e produzem, assim, a história ensinada. A teoria habermasiana da ação comunicativa é o principal alicerce teórico desta pesquisa; dessa forma, procurou-se relacionar essa teoria com a construção da memória social e seu papel no fazer pedagógico da sala de aula de história.

Accident selection methodology for TA-55 FSAR

International Nuclear Information System (INIS)

Letellier, B.C.; Pan, P.Y.; Sasser, M.K.

1995-01-01

In the past, the selection of representative accidents for refined analysis from the numerous scenarios identified in hazards analyses (HAs) has involved significant judgment and has been difficult to defend. As part of upgrading the Final Safety Analysis Report (FSAR) for the TA-55 plutonium facility at the Los Alamos National Laboratory, an accident selection process was developed that is mostly mechanical and reproducible in nature and fulfills the requirements of the Department of Energy (DOE) Standard 3009 and DOE Order 5480.23. Among the objectives specified by this guidance are the requirements that accident screening (1) consider accidents during normal and abnormal operating conditions, (2) consider both design basis and beyond design basis accidents, (3) characterize accidents by category (operational, natural phenomena, etc.) and by type (spill, explosion, fire, etc.), and (4) identify accidents that bound all foreseeable accident types. The accident selection process described here in the context of the TA-55 FSAR is applicable to all types of DOE facilities

JAERI's activities in JCO accident

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-09-01

The Japan Atomic Energy Research Institute (JAERI) was actively involved in a variety of technical supports and cooperative activities, such as advice on terminating the criticality condition, contamination checks of the residents and consultation services for the residents, as emergency response actions to the criticality accident at the uranium processing facility operated by the JCO Co. Ltd., which occurred on September 30, 1999. These activities were carried out in collaborative ways by the JAERI staff from the Tokai Research Establishment, Naka Fusion Research Establishment, Oarai Research Establishment, and Headquarter Office in Tokyo. As well, the JAERI was engaged in the post-accident activities such as identification of accident causes, analyses of the criticality accident, and dose assessment of exposed residents, to support the Headquarter for Accident Countermeasures of the Science and Technology Agency (STA), the Accident Investigation Committee and the Health Control Committee of the Nuclear Safety Commission of Japan (NSC). This report compiles the activities, that the JAERI has conducted to date, including the discussions on measures for terminating the criticality condition, evaluation of the fission number, radiation monitoring in the environment, dose assessment, analyses of criticality dynamics. (author)

3-D core modelling of RIA transient: the TMI-1 benchmark

International Nuclear Information System (INIS)

Ferraresi, P.; Studer, E.; Avvakumov, A.; Malofeev, V.; Diamond, D.; Bromley, B.

2001-01-01

The increase of fuel burn up in core management poses actually the problem of the evaluation of the deposited energy during Reactivity Insertion Accidents (RIA). In order to precisely evaluate this energy, 3-D approaches are used more and more frequently in core calculations. This 'best-estimate' approach requires the evaluation of code uncertainties. To contribute to this evaluation, a code benchmark has been launched. A 3-D modelling for the TMI-1 central Ejected Rod Accident with zero and intermediate initial powers was carried out with three different methods of calculation for an inserted reactivity respectively fixed at 1.2 $ and 1.26 $. The studies implemented by the neutronics codes PARCS (BNL) and CRONOS (IPSN/CEA) describe an homogeneous assembly, whereas the BARS (KI) code allows a pin-by-pin representation (CRONOS has both possibilities). All the calculations are consistent, the variation in figures resulting mainly from the method used to build cross sections and reflectors constants. The maximum rise in enthalpy for the intermediate initial power (33 % P N ) calculation is, for this academic calculation, about 30 cal/g. This work will be completed in a next step by an evaluation of the uncertainty induced by the uncertainty on model parameters, and a sensitivity study of the key parameters for a peripheral Rod Ejection Accident. (authors)

3-D core modelling of RIA transient: the TMI-1 benchmark

Energy Technology Data Exchange (ETDEWEB)

Ferraresi, P. [CEA Cadarache, Institut de Protection et de Surete Nucleaire, Dept. de Recherches en Securite, 13 - Saint Paul Lez Durance (France); Studer, E. [CEA Saclay, Dept. Modelisation de Systemes et Structures, 91 - Gif sur Yvette (France); Avvakumov, A.; Malofeev, V. [Nuclear Safety Institute of Russian Research Center, Kurchatov Institute, Moscow (Russian Federation); Diamond, D.; Bromley, B. [Nuclear Energy and Infrastructure Systems Div., Brookhaven National Lab., BNL, Upton, NY (United States)

2001-07-01

The increase of fuel burn up in core management poses actually the problem of the evaluation of the deposited energy during Reactivity Insertion Accidents (RIA). In order to precisely evaluate this energy, 3-D approaches are used more and more frequently in core calculations. This 'best-estimate' approach requires the evaluation of code uncertainties. To contribute to this evaluation, a code benchmark has been launched. A 3-D modelling for the TMI-1 central Ejected Rod Accident with zero and intermediate initial powers was carried out with three different methods of calculation for an inserted reactivity respectively fixed at 1.2 $ and 1.26 $. The studies implemented by the neutronics codes PARCS (BNL) and CRONOS (IPSN/CEA) describe an homogeneous assembly, whereas the BARS (KI) code allows a pin-by-pin representation (CRONOS has both possibilities). All the calculations are consistent, the variation in figures resulting mainly from the method used to build cross sections and reflectors constants. The maximum rise in enthalpy for the intermediate initial power (33 % P{sub N}) calculation is, for this academic calculation, about 30 cal/g. This work will be completed in a next step by an evaluation of the uncertainty induced by the uncertainty on model parameters, and a sensitivity study of the key parameters for a peripheral Rod Ejection Accident. (authors)

RIA for indol alkaloids

International Nuclear Information System (INIS)

Arens, H.

1979-01-01

The technique of RIAs for indol alkaloids (ajmaline, ergotamine, ergocristine, ergometrine, and lysergic acid) is described, and applications for this RIA and the RIA for raubasine and serpentine are mentioned. The indol alkaloide RIAs are shown to be suitable both for alkaloid distribution measurements in Catharantus and Rauwolfia plants and C. purpurea sclerotia as well as for the selection of high-efficiency strains and the optimisation of cultures of plant tissues and saprophytic fungi. (orig./MG) [de

Psychological and social impacts of post-accident situations: lessons from the Chernobyl accident

International Nuclear Information System (INIS)

Lochard, J.

1996-01-01

This paper presents the main features, from the psychological and social points of view, of the post-accident situation in the contaminated areas around Chernobyl. This is based on a series of surveys performed in the concerned territories of the CIS republics. The high level of stress affecting a large segment of the population is related to the perception of the situation by those living in a durably contaminated environment but also to the side-effects of some of the countermeasures adopted to mitigate the radiological consequences or to compensate the affected population. The distinction between the accident and the post-accident phase is enlarged to take into account the various phases characterizing the dynamics of the social response. Although the size of the catastrophe as well as the economic and political conditions that were prevailing at the time and after the accident have resulted in a maximal intensity of the reactions of the population, many lessons can be drawn for the management of potential post-accident situations. (author)

Computerized accident management support system: development for severe accident management

International Nuclear Information System (INIS)

Garcia, V.; Saiz, J.; Gomez, C.

1998-01-01

The activities involved in the international Halden Reactor Project (HRP), sponsored by the OECD, include the development of a Computerized Accident Management Support System (CAMS). The system was initially designed for its operation under normal conditions, operational transients and non severe accidents. Its purpose is to detect the plant status, analyzing the future evolution of the sequence (initially using the APROS simulation code) and the possible recovery and mitigation actions in case of an accident occurs. In order to widen the scope of CAMS to severe accident management issues, the integration of the MAAP code in the system has been proposed, as the contribution of the Spanish Electrical Sector to the project (with the coordination of DTN). To include this new capacity in CAMS is necessary to modify the system structure, including two new modules (Diagnosis and Adjustment). These modules are being developed currently for Pressurized Water Reactors and Boiling Water REactors, by the engineering of UNION FENOSA and IBERDROLA companies (respectively). This motion presents the characteristics of the new structure of the CAMS, as well as the general characteristics of the modules, developed by these companies in the framework of the Halden Reactor Project. (Author)

Development of Electrical Capacitance Sensors for Accident Tolerant Fuel (ATF) Testing at the Transient Reactor Test (TREAT) Facility

Energy Technology Data Exchange (ETDEWEB)

Liu, Maolong; Ryals, Matthew; Ali, Amir; Blandford, Edward; Jensen, Colby; Condie, Keith; Svoboda, John; O' Brien, Robert

2016-08-01

A variety of instruments are being developed and qualified to support the Accident Tolerant Fuels (ATF) program and future transient irradiations at the Transient Reactor Test (TREAT) facility at Idaho National Laboratory (INL). The University of New Mexico (UNM) is working with INL to develop capacitance-based void sensors for determining the timing of critical boiling phenomena in static capsule fuel testing and the volume-averaged void fraction in flow-boiling in-pile water loop fuel testing. The static capsule sensor developed at INL is a plate-type configuration, while UNM is utilizing a ring-type capacitance sensor. Each sensor design has been theoretically and experimentally investigated at INL and UNM. Experiments are being performed at INL in an autoclave to investigate the performance of these sensors under representative Pressurized Water Reactor (PWR) conditions in a static capsule. Experiments have been performed at UNM using air-water two-phase flow to determine the sensitivity and time response of the capacitance sensor under a flow boiling configuration. Initial measurements from the capacitance sensor have demonstrated the validity of the concept to enable real-time measurement of void fraction. The next steps include designing the cabling interface with the flow loop at UNM for Reactivity Initiated Accident (RIA) ATF testing at TREAT and further characterization of the measurement response for each sensor under varying conditions by experiments and modeling.

Oxidation of SiC cladding under Loss of Coolant Accident (LOCA) conditions in LWRs

International Nuclear Information System (INIS)

Lee, Y.; Yue, C.; Arnold, R. P.; McKrell, T. J.; Kazimi, M. S.

2012-01-01

An experimental assessment of Silicon Carbide (SiC) cladding oxidation rate in steam under conditions representative of Loss of Coolant Accidents (LOCA) in light water reactors (LWRs) was conducted. SiC oxidation tests were performed with monolithic alpha phase tubular samples in a vertical quartz tube at a steam temperature of 1140 deg. C and steam velocity range of 1 to 10 m/sec, at atmospheric pressure. Linear weight loss of SiC samples due to boundary layer controlled reaction of silica scale (SiO 2 volatilization) was experimentally observed. The weight loss rate increased with increasing steam flow rate. Over the range of test conditions, SiC oxidation rates were shown to be about 3 orders of magnitude lower than the oxidation rates of zircaloy 4. A SiC volatilization correlation for developing laminar flow in a vertical channel is formulated. (authors)

Accident scenario diagnostics with neural networks

International Nuclear Information System (INIS)

Guo, Z.

1992-01-01

Nuclear power plants are very complex systems. The diagnoses of transients or accident conditions is very difficult because a large amount of information, which is often noisy, or intermittent, or even incomplete, need to be processed in real time. To demonstrate their potential application to nuclear power plants, neural networks axe used to monitor the accident scenarios simulated by the training simulator of TVA's Watts Bar Nuclear Power Plant. A self-organization network is used to compress original data to reduce the total number of training patterns. Different accident scenarios are closely related to different key parameters which distinguish one accident scenario from another. Therefore, the accident scenarios can be monitored by a set of small size neural networks, called modular networks, each one of which monitors only one assigned accident scenario, to obtain fast training and recall. Sensitivity analysis is applied to select proper input variables for modular networks

Preliminary experiment design of graphite dust emission measurement under accident conditions for HTGR

Energy Technology Data Exchange (ETDEWEB)

Peng, Wei, E-mail: pengwei@tsinghua.edu.cn [Institute of Nuclear and New Energy Technology of Tsinghua University, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 100084 (China); Chen, Tao; Sun, Qi; Wang, Jie [Institute of Nuclear and New Energy Technology of Tsinghua University, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 100084 (China); Yu, Suyuan, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Education, Tsinghua University, Beijing 100084 (China)

2017-05-15

Highlights: • A theoretical analysis is used to predict the total graphite dust release for an AVR LOCA. • Similarity criteria must be satisfied between the experiment and the actual HTGR system. • Model experiments should be conducted to predict the graphite dust resuspension rate. - Abstract: The graphite dust movement behavior is significant for the safety analyses of high-temperature gas cooled reactor (HTGR). The graphite dust release for accident conditions is an important source term for HTGR safety analyses. Depressurization release tests are not practical in HTGR because of a radioactivity release to the environment. Thus, a theoretical analysis and similarity principles were used to design a group of modeling experiments. Modeling experiments for fan start-up and depressurization process and actual experiments of helium circulator start-up in an HTGR were used to predict the rate of graphite dust resuspension and the graphite dust concentration, which can be used to predict the graphite dust release during accidents. The modeling experiments are easy to realize and the helium circulator start-up test does not harm the reactor system or the environment, so this experiment program is easily achieved. The revised Rock’n’Roll model was then used to calculate the AVR reactor release. The calculation results indicate that the total graphite dust releases during a LOCA will be about 0.65 g in AVR.

Thermal hydraulic features of the TMI accident

International Nuclear Information System (INIS)

Tolman, B.

1985-01-01

The TMI-2 accident resulted in extensive core damage and recent data confirms that the reactor vessel was challenged from molten core materials. A hypothesized TMI accident sencario is presented that consistently explains the TMI data and is also consistent with research findings from independent severe fuel damage experiements. The TMI data will prove useful in confirming our understanding of severe core damage accidents under realistic reactor systems conditions. This understanding will aid in addressing safety and regulatory issues related to severe core damage accidents in light water reactors

Safety regulations regarding to accident monitoring and accident sampling at Russian NPPs with VVER type reactors

International Nuclear Information System (INIS)

Sharafutdinov, Rachet; Lankin, Michail; Kharitonova, Nataliya

2014-01-01

The paper describes a tendency by development of regulatory document requirements related to accident monitoring and accident sampling at Russia's NPPs. Lessons learned from the Fukushima Daiichi accident pointed at the importance and necessary to carry out an additional safety check at Russia's nuclear power plants in the preparedness for management of severe accidents at NPPs. Planned measures for improvement of severe accidents management include development and implementation of the accident instrumentation systems, providing, monitoring, management and storage of information in a severe accident conditions. The draft of Safety Guidelines <accident monitoring system of nuclear power plants with VVER reactors' prepared by Scientific and Engineering Centre for Nuclear and Radiation Safety (SEC NRS) established the main criteria for accident monitoring instrumentation that can monitor relevant plant parameters in the reactor and inside containment during and after a severe accident in nuclear power plants. Development of these safety guidelines is in line with the recommendations of IAEA Action Plan on Nuclear Safety in response to the Fukushima Daiichi event and recommendations of the IAEA Nuclear Energy series Report <<Accident Monitoring Systems for Nuclear Power Plants' (Draft V 2.7). The paper presents the principles, which are used as the basis for selection of plant parameters for accident monitoring and for establishing of accident monitoring instrumentation. The recommendations to the accident sampling system capable to obtain the representative reactor coolant and containment air and fluid samples that support accurate analytical results for the parameters of interest are considered. The radiological and chemistry parameters to be monitored for primary coolant and sump and for containment air are specified. (author)

Condições higiênico-sanitárias dos portos de Manaus-AM, 2007-2010 | Sanitary conditions of the ports of Manaus-AM, 2007-2010

Directory of Open Access Journals (Sweden)

Jerfeson Nepumuceno Caldas

2017-08-01

Full Text Available Introdução: Um porto organizado dispõe de infraestrutura física, serviços e processos e é construído e aparelhado para atender às necessidades da navegação, movimentação e armazenagem de mercadorias e deslocamento de viajantes, sob a responsabilidade de uma autoridade portuária. Objetivo: Analisar os determinantes das condições higiênico-sanitárias dos portos organizados da cidade de Manaus-AM. Método: Estudo transversal e descritivo com base nos dados da Coordenação de Vigilância Sanitária de Portos, Aeroportos, Fronteiras e Recintos Alfandegados do estado do Amazonas. Os dados foram coletados dos termos de inspeção das instalações físicas dos portos emitidos no período de janeiro de 2007 a dezembro de 2010. O processamento e análise dos dados ocorreram através de planilhas do Microsoft Excel e calculadas as distribuições percentuais. A interpretação e análise dos dados ocorreram conforme categorias de análise da RDC nº 72, de 29 de dezembro de 2009, da Agência Nacional de Vigilância Sanitária. Resultados: Observou-se que os processos de higiene e limpeza e os serviços de alimentação apresentaram a maior porcentagem de inspeção e mais da metade se mostrou insatisfatória. Conclusões: Os resultados demonstraram que as autoridades portuárias devem investir no controle das condições higiênico-sanitária das instalações, processos e serviços dos portos organizados, para mitigar potenciais fatores de risco capazes de produzir agravos à saúde. =============================================== Introduction: An organized port has physical infrastructure, services and processes, and is built and equipped to meet the needs of navigation, handling and storage of goods and travelers in general, under the responsibility of a port authority. Objective: The objective of this study was to analyze the determinants of the hygienic-sanitary conditions of the organized ports of the city of Manaus-AM. Method

Condições higiênico-sanitárias de uma dieta hospitalar Hygienic and sanitary conditions of a hospital diet

Directory of Open Access Journals (Sweden)

Consuelo Lúcia Sousa

2003-01-01

Full Text Available Buscou-se avaliar as condições higiênico-sanitárias da dieta branda servida em um hospital geral da cidade de Belém, Pará, através da análise microbiológica de seus componentes (coliformes fecais, Staphylococcus aureus e Salmonella e dos utensílios, equipamentos e mãos de funcionários (coliformes fecais, Staphylococcus aureus, bem como elaborar um Relatório Técnico de Inspeção da Unidade de Alimentação e Nutrição do hospital, baseado no Anexo II da Portaria 1428 de 26/11/1993, para a implantação das Boas Práticas de Fabricação. Em nenhuma das amostras foi detectada a presença de Salmonella ou Staphylococcus aureus; entretanto, os componentes da dieta, equipamentos e utensílios apresentaram 100% de coliformes fecais, assim como as mãos de duas funcionárias. Os principais pontos observados para o relatório técnico foram: padrão de identidade e qualidade, condições ambientais, instalações e saneamento, equipamentos e utensílios, recursos humanos, tecnologia empregada, controle de qualidade, garantia de qualidade, armazenagem, desinfecção e desinfestação. Através desta avaliação foram constatadas as péssimas condições higiênico-sanitárias da referida Unidade de Alimentação e Nutrição.The objectives of this work were to evaluate the hygienic and sanitary conditions of a light diet of a hospital in the city of Belém, state of Pará (Brazil, using microbiological analysis of its compounds (fecal coliforms, Staphylococcus aureus and Salmonella and of utensils, equipment's and employees' hands (fecal coliforms, Staphylococcus aureus, and to provide an inspection technical report of the hospital Food and Nutrition Unit, according to Annex II of the 1428th Regulation (11/26/1993 of the Ministry of Health to verify the implementation of the Good Manufacturing Practices. None of the samples presented Salmonella or Staphylococcus aureus; however, the compounds, utensils and equipments presented 100% of

Core dynamics of HTR under ATWS and accident conditions

International Nuclear Information System (INIS)

Nabbi, R.

1988-05-01

The systematic classification of the ATWS has been undertaken by analogy to the considerations made for LWR. The initiating events of ATWS and protection actions of safety systems resulting from monitoring of the system variables have been described. The main emphasis of this work is the analysis of the core dynamic consequences of scram failure during the anticipated transients. The investigation has shown that because of the temperature feedback mechanisms a temperature rise during the ATWS results in a self-shutdown of the reactor. Further inherent safety features of the HTR - conditioned by the high heat capacity of the core and by the compressibility of the coolant - do effectively counteract an undesirable increase of temperature and pressure in the primary circuit. In case of the long-term failure of the forced cooling and following core heatup, neutron physical phenomena appear which determine the reactivity behaviour of the HTR. They are, for instance, the decay of Xenon 135, release of the fission products and subsiding of the top reflector. The results of the computer simulations show that a recriticality has to be excluded during the first 2 days if the reactor is shutdown by the reflector rods at the beginning of the accident. (orig./HP) [de

Analyses of conditions in a large, dry PWR containment during an TMLB' accident sequence

International Nuclear Information System (INIS)

Sweet, D.W.; Roberts, G.J.

1994-01-01

The aim of the paper is to give an assessment of the conditions which would develop in the large, dry containment of a modern Westinghouse-type PWR during a severe accident where all safety systems are unavailable. The analysis is based principally on the results of calculations using the CONTAIN code, with a 4 cell model of the containment, for a station blackout (TMLB') scenario in which the vessel is assumed to fail at high pressure. In particular, the following are noted: (i) If much of the debris is in contact with water, so that decay heat can boil water directly, then the pressure rises steadily to reach the assumed containment failure point after 11/2 to 2 days. If most of the debris becomes isolated from water, for example, because of water is held up on the containment floors and in sumps and drains, the pressure rises too slowly to threaten the containment on this timescale. (ii) If a core-concrete interaction occurs, most of the associated fission product release takes place soon after relocation of molten fuel to the containment. The aerosols which transport these (and other non-gaseous fission products released earlier in the accident) in the containment agglomerate and settle. As a result, 0.1% or less of the aerosols remain airborne a day after the start of the accident. (iii) Hydrogen and carbon monoxide, which would accumulate in the containment are not expected to burn because the atmosphere would be inerted by steam. If, however, enough of the steam is condensed, for example, by recovering the containment sprays, a burn could occur but the resulting pressure spike is unlikely to threaten the containment unless a transition to detonation occurs. 6 refs., 6 tabs., 12 figs

Radiation conditions in the Oryol region territory impacted by radioactive contamination caused by the Chernobyl NPP accident

Directory of Open Access Journals (Sweden)

G. L. Zakharchenko

2016-01-01

Full Text Available Research objective is retrospective analysis of radiation conditions in the Oryol region during 1986- 2015 and assessment of efficacy of the carried out sanitary and preventive activities for population protection against radiation contamination caused by the Chernobyl NPP accident.Article materials were own memoirs of events participants, analysis of federal state statistic surveillance forms 3-DOZ across the Oryol region, f-35 “Data on patients with malignant neoplasms, f-12 “Report on MPI activities”. Risk assessment of oncological diseases occurrence is carried out on the basis of AAED for 1986- 2014 using the method of population exposure risk assessment due to long uniform man-made irradiation in small doses. Results of medical and sociological research of genetic, environmental, professional and lifestyle factors were obtained using the method of cancer patients’ anonymous survey. Data on "risk" factors were obtained from 467 patients hospitalized at the Budgetary Health Care Institution of the Oryol region “Oryol oncology clinic”; a specially developed questionnaire with 60 questions was filled out.The article employs the method of retrospective analysis of laboratory and tool research and calculation of dose loads on the Oryol region population, executed throughout the whole period after the accident.This article provides results of the carried out laboratory research of foodstuff, environment objects describing the radiation conditions in the Oryol region since the first days after the Chernobyl NPP accident in 1986 till 2015.We presented a number of activities aimed at liquidation of man-caused radiation accident consequences which were developed and executed by the experts of the Oryol region sanitary and epidemiology service in 1986-2015. On the basis of the above-stated one may draw the conclusions listed below. Due to interdepartmental interaction and active work of executive authorities in the Oryol region, the

Assessing information needs and instrument availability for a pressurized water reactor during severe accidents

Energy Technology Data Exchange (ETDEWEB)

Hanson, Duane J. (Idaho National Engineering Laboratory, Idaho Falls, ID 83415 (United States)); Arcieri, William C. (Idaho National Engineering Laboratory, Idaho Falls, ID 83415 (United States)); Ward, Leonard W. (Idaho National Engineering Laboratory, Idaho Falls, ID 83415 (United States))

1994-07-01

A five-step methodology was developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information that personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and severe accident conditions, to evaluate the availability of the instrumentation to supply needed plant information. This methodology was applied to a pressurized water reactor with a large dry containment and the results are presented. A companion article describes application of the methodology to a boiling water reactor with a Mark I containment. ((orig.))

Assessing information needs and instrument availability for a pressurized water reactor during severe accidents

International Nuclear Information System (INIS)

Hanson, Duane J.; Arcieri, William C.; Ward, Leonard W.

1994-01-01

A five-step methodology was developed to evaluate information needs for nuclear power plants under accident conditions and the availability of plant instrumentation during severe accidents. Step 1 examines the credible accidents and their relationships to plant safety functions. Step 2 determines the information that personnel involved in accident management will need to understand plant behavior. Step 3 determines the capability of the instrumentation to function properly under severe accident conditions. Step 4 determines the conditions expected during the identified severe accidents. Step 5 compares the instrument capabilities and severe accident conditions, to evaluate the availability of the instrumentation to supply needed plant information. This methodology was applied to a pressurized water reactor with a large dry containment and the results are presented. A companion article describes application of the methodology to a boiling water reactor with a Mark I containment. ((orig.))

Strategy generator in computerized accident management support system

International Nuclear Information System (INIS)

Sirola, M.

1994-02-01

An increased interest for research in the field of accident management of nuclear power plants can be noted. Several international programmes have been started in order to be able to understand the basic physical and chemical phenomena in accident conditions. A feasibility study has shown that it would be possible to design and develop a computerized support system for plant staff in accident situations. To achieve this goal the Halden Project has initiated a research programme on Computerized Accident Management Support (CAMS project). The aim is to utilize the capabilities of computerized tools to support the plant staff during the various accident stages. The system will include identification of the accident state, assessment of the future development of the accident and planning of accident mitigation strategies. A prototype is developed to support operators and the Technical Support Centre in decision making during serious accidents in nuclear power plants. A rule based system has been built to take care of the strategy generation. This system assists plant personnel in planning control proposals and mitigation strategies from normal operation to severe accident conditions. The idea of a safety objective tree and knowledge from the emergency procedures have been used. Future prediction requires good state identification of the plant status and some knowledge about the history of some critical variables. The information needs to be validated as well. Accurate calculations in simulators and a large database including all important information from the plant will help the strategy planning. (orig.). (40 refs., 20 figs.)

Impact of the Aegean Sea oil spill on the subtidal fine sand macrobenthic community of the Ares-Betanzos Ria (Northwest Spain)

International Nuclear Information System (INIS)

Gomez Gesteira, J.L.; Dauvin, J.C.

2005-01-01

Two sites located in the sublittoral fine-sand macrobenthic community of the Ares-Betanzos Ria were sampled over four years (December 1992-November 1996) in the wake of the Aegean Sea oil spill. This sampling revealed that the petroleum had affected the structure and abundance of this community, as well as the number of taxa present. In this context, the results of the biotic index and the biotic coefficient were insufficient; however, study of the synthetic parameters, particularly through multivariate analysis, showed that the community went through three successive and distinct phases over time. A short period of high mortality in some species, especially amphipods, was followed by a period of low abundance that lasted until the spring of 1995. A period of recovery began in the second half of 1995 and continued through to the end of 1996, when the survey ended. The community showed a gradual evolution back towards the conditions observed immediately after the spill, when abundance of the more resistant species was still high. Despite this similarity, the last period exhibits a new structure, clearly separate from the two previous periods. This study provides information about the short-term effects of the Aegean Sea oil spill on the fine sand bottoms of the sites surveyed in the Ares-Betanzos Ria. This information could also serve as a baseline for identifying the effects of a more recent accident, the Prestige oil spill, in which similar communities in other Galician rias were polluted in 2002-2003. (author)

49 CFR 195.52 - Telephonic notice of certain accidents.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Telephonic notice of certain accidents. 195.52... TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE Annual, Accident, and Safety-Related Condition Reporting § 195.52 Telephonic notice of certain accidents. (a) At the earliest practicable moment following discovery of a...

Accident management for severe accidents

International Nuclear Information System (INIS)

Bari, R.A.; Pratt, W.T.; Lehner, J.; Leonard, M.; Disalvo, R.; Sheron, B.

1988-01-01

The management of severe accidents in light water reactors is receiving much attention in several countries. The reduction of risk by measures and/or actions that would affect the behavior of a severe accident is discussed. The research program that is being conducted by the US Nuclear Regulatory Commission focuses on both in-vessel accident management and containment and release accident management. The key issues and approaches taken in this program are summarized. 6 refs

Performance behavior of the passive containment cooling system of a natural circulation BWR during postulated accident condition

International Nuclear Information System (INIS)

Kumar, Mukesh; Nayak, A.K.; Jain, Vikas; Vijayan, P.K.; Saha, D.; Sinha, R.K.

2011-01-01

Passive systems are playing prominent role in the development of innovative nuclear reactor systems due to their simplicity, enhanced safety, reliability and economy. These systems are being considered for normal operation as well as accidental conditions of reactor following a postulated accident scenario to preclude the scenarios arising out of failure of active systems as well as to minimize the operator intervention. Indian innovative reactor AHWR being designed for thorium utilization employs various passive safety concepts. As containment is the ultimate barrier to the release of radioactivity, passive concepts are being employed in BWRs for minimize peak containment pressure in the containment during a postulated accident condition like LOCA. The concept of passive containment cooling system (PCCS) in the AHWR comprises of inclined tube heat exchangers located underneath an elevated pool that removes the heat from the steam-air atmosphere of containment following a LOCA by natural circulation of water inside the tubes. The steam condenses on the external surface of tubes of PCCS in addition to the wall of the containment which in turn depressurizes the containment. This paper deals with the performance assessment of PCCS of AHWR during a postulated design basis LOCA by using the best estimate code RELAP5/Mod3.2. (author)

An estimation of the accident sequence of the LOCA groups for the PSA model of the KSNP

International Nuclear Information System (INIS)

Han, Seok Jung; Yang, Joon Eon

2004-01-01

A new trend of the probabilistic safety assessment (PSA) technology is to improve and enhance the current PSA model to be adequate for risk-informed applications (RIA). Requirements of a PSA model for the RIA are summarized as (1) reduction of the conservatism in the model utilizing all available information and (2) consideration of the specific features of a plant as designed, as operated. This is because the PSA based on conservatism and insufficient consideration of the plant-specific features resulted in a shadow effect on the assessment results. When a PSA model is used in a risk-informed application, more precise risk-information is more helpful to decision making process, so the reduction of the conservatism and the consideration of the plant-specific features in a PSA model are the most essential elements. Recently, an effort has been performed to modify the current PSA model for the Korea Standard Nuclear Power plant (KSNP) to be used in risk-informed applications. A re-estimation of the accident sequence of the loss of coolant accident (LOCA) groups for the PSA model of the KSNP has been performed

Severe Accident Test Station Design Document

Energy Technology Data Exchange (ETDEWEB)

Snead, Mary A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yan, Yong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Howell, Michael [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Keiser, James R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-09-01

The purpose of the ORNL severe accident test station (SATS) is to provide a platform for evaluation of advanced fuels under projected beyond design basis accident (BDBA) conditions. The SATS delivers the capability to map the behavior of advanced fuels concepts under accident scenarios across various temperature and pressure profiles, steam and steam-hydrogen gas mixtures, and thermal shock. The overall facility will include parallel capabilities for examination of fuels and irradiated materials (in-cell) and non-irradiated materials (out-of-cell) at BDBA conditions as well as design basis accident (DBA) or loss of coolant accident (LOCA) conditions. Also, a supporting analytical infrastructure to provide the data-needs for the fuel-modeling components of the Fuel Cycle Research and Development (FCRD) program will be put in place in a parallel manner. This design report contains the information for the first, second and third phases of design and construction of the SATS. The first phase consisted of the design and construction of an out-of-cell BDBA module intended for examination of non-irradiated materials. The second phase of this work was to construct the BDBA in-cell module to test irradiated fuels and materials as well as the module for DBA (i.e. LOCA) testing out-of-cell, The third phase was to build the in-cell DBA module. The details of the design constraints and requirements for the in-cell facility have been closely captured during the deployment of the out-of-cell SATS modules to ensure effective future implementation of the in-cell modules.

Severe Accident Test Station Design Document

International Nuclear Information System (INIS)

Snead, Mary A.; Yan, Yong; Howell, Michael; Keiser, James R.; Terrani, Kurt A.

2015-01-01

The purpose of the ORNL severe accident test station (SATS) is to provide a platform for evaluation of advanced fuels under projected beyond design basis accident (BDBA) conditions. The SATS delivers the capability to map the behavior of advanced fuels concepts under accident scenarios across various temperature and pressure profiles, steam and steam-hydrogen gas mixtures, and thermal shock. The overall facility will include parallel capabilities for examination of fuels and irradiated materials (in-cell) and non-irradiated materials (out-of-cell) at BDBA conditions as well as design basis accident (DBA) or loss of coolant accident (LOCA) conditions. Also, a supporting analytical infrastructure to provide the data-needs for the fuel-modeling components of the Fuel Cycle Research and Development (FCRD) program will be put in place in a parallel manner. This design report contains the information for the first, second and third phases of design and construction of the SATS. The first phase consisted of the design and construction of an out-of-cell BDBA module intended for examination of non-irradiated materials. The second phase of this work was to construct the BDBA in-cell module to test irradiated fuels and materials as well as the module for DBA (i.e. LOCA) testing out-of-cell, The third phase was to build the in-cell DBA module. The details of the design constraints and requirements for the in-cell facility have been closely captured during the deployment of the out-of-cell SATS modules to ensure effective future implementation of the in-cell modules.

Flow behavior of volume-heated boiling pools: implications with respect to transition phase accident conditions

International Nuclear Information System (INIS)

Ginsberg, T.; Jones, O.C. Jr.; Chen, J.C.

1979-01-01

Observations of two-phase flow fields in single-component volume-heated boiling pools were made. Photographic observations, together with pool-average void fraction measurements, indicate that the churn-turbulent flow regime is stable for superficial vapor velocities up to nearly five times the Kutateladze dispersal limit. Within this range of conditions, a churn-turbulent drift flux model provides a reasonable prediction of the pool-average void fraction data. An extrapolation of the data to transition phase accident conditions suggests that intense boilup could occur where the pool-average void fraction would be >0.6 for steel vaporization rates equivalent to power levels >1% of nominal liquid-metal fast breeder reactor power density. The extended stability of bubbly flow to unusually large vapor fluxes and void fractions, observed in some experiments, is a major unresolved issue

Comparison and verification of two computer programs used to analyze ventilation systems under accident conditions

International Nuclear Information System (INIS)

Hartig, S.H.; Wurz, D.E.; Arnitz, T.; Ruedinger, V.

1985-01-01

Two computer codes, TVENT and EVENT, which were developed at the Los Alamos National Laboratory (LANL) for the analysis of ventilation systems, have been modified to model air-cleaning systems that include active components with time-dependent flow-resistance characteristics. With both modified programs, fluid-dynamic transients were calculated for a test facility used to simulate accident conditions in air-cleaning systems. Experiments were performed in the test facility whereby flow and pressure transients were generated with the help of two quick-actuating air-stream control valves. The numerical calculations are compared with the test results. Although EVENT makes use of a more complex theoretical flow model than TVENT, the numerical simulations of both codes were found to be very similar for the flow conditions studied and to closely follow the experimental results

Aula de história: subjetividade e memória na aprendizagem de alunos

OpenAIRE

Scoz, Beatriz Judith Lima; Rodrigues, Vilma Nardes Silva

2015-01-01

Este artigo apresenta o relato de uma pesquisa sobre as relações entre memória individual e memória coletiva nas aulas de História para compreender suas interferências na produção de sentidos subjetivos dos alunos na aprendizagem de História. A coleta de dados foi feita a partir do filme "Narradores de Javé" e da "conversação livre" com alunos da 8a série de uma escola pública de São Paulo. A pesquisa fundamenta-se nas concepções teóricas de Halbwachs e Placco, & Souza acerca da memória. No q...

The Fuel Accident Condition Simulator (FACS) furnace system for high temperature performance testing of VHTR fuel

Energy Technology Data Exchange (ETDEWEB)

Demkowicz, Paul A., E-mail: paul.demkowicz@inl.gov [Idaho National Laboratory, 2525 Fremont Avenue, MS 3860, Idaho Falls, ID 83415-3860 (United States); Laug, David V.; Scates, Dawn M.; Reber, Edward L.; Roybal, Lyle G.; Walter, John B.; Harp, Jason M. [Idaho National Laboratory, 2525 Fremont Avenue, MS 3860, Idaho Falls, ID 83415-3860 (United States); Morris, Robert N. [Oak Ridge National Laboratory, 1 Bethel Valley Road, Oak Ridge, TN 37831 (United States)

2012-10-15

Highlights: Black-Right-Pointing-Pointer A system has been developed for safety testing of irradiated coated particle fuel. Black-Right-Pointing-Pointer FACS system is designed to facilitate remote operation in a shielded hot cell. Black-Right-Pointing-Pointer System will measure release of fission gases and condensable fission products. Black-Right-Pointing-Pointer Fuel performance can be evaluated at temperatures as high as 2000 Degree-Sign C in flowing helium. - Abstract: The AGR-1 irradiation of TRISO-coated particle fuel specimens was recently completed and represents the most successful such irradiation in US history, reaching peak burnups of greater than 19% FIMA with zero failures out of 300,000 particles. An extensive post-irradiation examination (PIE) campaign will be conducted on the AGR-1 fuel in order to characterize the irradiated fuel properties, assess the in-pile fuel performance in terms of coating integrity and fission metals release, and determine the fission product retention behavior during high temperature safety testing. A new furnace system has been designed, built, and tested to perform high temperature accident tests. The Fuel Accident Condition Simulator furnace system is designed to heat fuel specimens at temperatures up to 2000 Degree-Sign C in helium while monitoring the release of volatile fission metals (e.g. Cs, Ag, Sr, and Eu), iodine, and fission gases (Kr, Xe). Fission gases released from the fuel to the sweep gas are monitored in real time using dual cryogenic traps fitted with high purity germanium detectors. Condensable fission products are collected on a plate attached to a water-cooled cold finger that can be exchanged periodically without interrupting the test. Analysis of fission products on the condensation plates involves dry gamma counting followed by chemical analysis of selected isotopes. This paper will describe design and operational details of the Fuel Accident Condition Simulator furnace system and the associated

OSSA. A second generation of severe accident management

International Nuclear Information System (INIS)

Sauvage, E.C.; Musoyan, G.; Ducros, V.D.

2009-01-01

Nowadays the severe accident and their management are an integrated part of the new generation of power plants. The EPR, as the third generation of nuclear plants, includes both systems and instrumentation to mitigate a severe accident, but also a new generation of severe accident management guidelines: the OSSA. Severe accident management guidelines are highly dependent on human means available: emergency organization actors, training and knowledge shall be taken in consideration in an innovative way. Their impacts on ergonomy and content of the document lead to a new generation of guidelines with several innovative features. This second generation of severe accident management guidelines was developed in parallel with the PSA level 2, the human reliability analyses, the validation and verification process, the severe accident simulator progresses. By taking in consideration this variety of input the OSSA were developed in a user aspect orientation. For example in the OSSA a larger responsibility is given to the operational crew to better support the technical support group evaluation. Their existing knowledge of the plant and of the systems and instrumentation is used. This collaboration work implies a strong communication tool that has been developed to enhance the permanent communication within the emergency organization, but although to ensure the main up-to-date information for evaluation will be available where required. The entry condition is based on a strong and stand alone diagnostic for all plant states, that uses in particular a curve of core exit temperature as a function of primary pressure for a fixed core cladding temperature, or its equivalent in term of containment conditions. It ensures relatively consistent core conditions on entry. A first criterion for ultimate final primary depressurization is provided, ensuring all attempts to reflood the core with the available means have been ensured before the OSSA entry condition is reached. This

Graphite Oxidation Simulation in HTR Accident Conditions

Energy Technology Data Exchange (ETDEWEB)

El-Genk, Mohamed

2012-10-19

Massive air and water ingress, following a pipe break or leak in steam-generator tubes, is a design-basis accident for high-temperature reactors (HTRs). Analysis of these accidents in both prismatic and pebble bed HTRs requires state-of-the-art capability for predictions of: 1) oxidation kinetics, 2) air helium gas mixture stratification and diffusion into the core following the depressurization, 3) transport of multi-species gas mixture, and 4) graphite corrosion. This project will develop a multi-dimensional, comprehensive oxidation kinetics model of graphite in HTRs, with diverse capabilities for handling different flow regimes. The chemical kinetics/multi-species transport model for graphite burning and oxidation will account for temperature-related changes in the properties of graphite, oxidants (O2, H2O, CO), reaction products (CO, CO2, H2, CH4) and other gases in the mixture (He and N2). The model will treat the oxidation and corrosion of graphite in geometries representative of HTR core component at temperatures of 900°C or higher. The developed chemical reaction kinetics model will be user-friendly for coupling to full core analysis codes such as MELCOR and RELAP, as well as computational fluid dynamics (CFD) codes such as CD-adapco. The research team will solve governing equations for the multi-dimensional flow and the chemical reactions and kinetics using Simulink, an extension of the MATLAB solver, and will validate and benchmark the model's predictions using reported experimental data. Researchers will develop an interface to couple the validated model to a commercially available CFD fluid flow and thermal-hydraulic model of the reactor , and will perform a simulation of a pipe break in a prismatic core HTR, with the potential for future application to a pebble-bed type HTR.

Psychological aspects of accident prevention in mines

Energy Technology Data Exchange (ETDEWEB)

Lukestikova, M

1981-04-01

This paper duscusses ways of preventing work accidents and increasing work safety in underground black coal mines. Specific conditions of underground operations in coal mines are stressed. Elements of work accident prevention are analyzed: reducing hazards by introducing safer technology, automation and mechanization of operations associated with hazards, introducing special measures within the framework of safety engineering. Dependence of accident rate on such factors as personnel training, age, motivation, qualifications, and labor discipline is discussed. Investigations indicate that miner motivation plays a significant role in accident prevention. A high degree of labor motivation successfully reduces accident rate and a low degree of motivation increases accident rate. Role of labor collective in labor motivation as well as a correct system of wage incentives are evaluated. Methods of personnel training aimed at reducing accident rate are described. Role of a technique by which a group of miners attempts to find a solution to a work safety problem by amassing all ideas spontaneously contributed by participants is stressed.

TASAC a computer program for thermal analysis of severe accident conditions. Version 3/01, Dec 1991. Model description and user's guide

International Nuclear Information System (INIS)

Stempniewicz, M.; Marks, P.; Salwa, K.

1992-06-01

TASAC (Thermal Analysis of Severe Accident Conditions) is computer code developed in the Institute of Atomic Energy written in FORTRAN 77 for the digital computer analysis of PWR rod bundle behaviour during severe accident conditions. The code has the ability to model an early stage of core degradation including heat transfer inside the rods, convective and radiative heat exchange as well as cladding interactions with coolant and fuel, hydrogen generation, melting, relocations and refreezing of fuel rod materials with dissolution of UO 2 and ZrO 2 in liquid phase. The code was applied for the simulation of International Standard Problem number 28, performed on PHEBUS test facility. This report contains the program physical models description, detailed description of input data requirements and results of code verification. The main directions for future TASAC code development are formulated. (author). 20 refs, 39 figs, 4 tabs

Prediction of failure of highly irradiated Zircaloy clad tubes under reactivity initiated accidents

International Nuclear Information System (INIS)

Jernkvist, L.O.

2003-01-01

This paper deals with failure of irradiated Zircaloy tubes under the heat-up stage of a reactivity initiated accident (RIA). More precisely, by use of a model for plastic strain localization and necking failure, we theoretically analyse the effects of local surface defects on clad ductility and survivability under RIA. The results show that even very shallow surface defects, e.g. arising from a non-uniform or partially spilled oxide layer, have a strong limiting effect on clad ductility. Moreover, in presence of surface defects, the ability of the clad tube to expand radially without necking failure is found to be extremely sensitive to the stress biaxiality ratio σ zz /σ θθ , which is here assumed to be in the range from 0 to 1. The results of our analysis are compared with clad ductility data available in literature, and their consequences for clad failure prediction under RIA are discussed. In particular, the results raise serious concerns regarding the applicability of failure criteria, which are based on clad strain energy density. These criteria do not capture the observed sensitivity to stress biaxiality on clad failure propensity. (author)

Containment severe accident thermohydraulic phenomena

International Nuclear Information System (INIS)

Frid, W.

1991-08-01

This report describes and discusses the containment accident progression and the important severe accident containment thermohydraulic phenomena. The overall objective of the report is to provide a rather detailed presentation of the present status of phenomenological knowledge, including an account of relevant experimental investigations and to discuss, to some extent, the modelling approach used in the MAAP 3.0 computer code. The MAAP code has been used in Sweden as the main tool in the analysis of severe accidents. The dependence of the containment accident progression and containment phenomena on the initial conditions, which in turn are heavily dependent on the in-vessel accident progression and phenomena as well as associated uncertainties, is emphasized. The report is in three parts dealing with: * Swedish reactor containments, the severe accident mitigation programme in Sweden and containment accident progression in Swedish PWRs and BWRs as predicted by the MAAP 3.0 code. * Key non-energetic ex-vessel phenomena (melt fragmentation in water, melt quenching and coolability, core-concrete interaction and high temperature in containment). * Early containment threats due to energetic events (hydrogen combustion, high pressure melt ejection and direct containment heating, and ex-vessel steam explosions). The report concludes that our understanding of the containment severe accident progression and phenomena has improved very significantly over the parts ten years and, thereby, our ability to assess containment threats, to quantify uncertainties, and to interpret the results of experiments and computer code calculations have also increased. (au)

Expert software for accident identification

International Nuclear Information System (INIS)

Dobnikar, M.; Nemec, T.; Muehleisen, A.

2003-01-01

Each type of an accident in a Nuclear Power Plant (NPP) causes immediately after the start of the accident variations of physical parameters that are typical for that type of the accident thus enabling its identification. Examples of these parameter are: decrease of reactor coolant system pressure, increase of radiation level in the containment, increase of pressure in the containment. An expert software enabling a fast preliminary identification of the type of the accident in Krsko NPP has been developed. As input data selected typical parameters from Emergency Response Data System (ERDS) of the Krsko NPP are used. Based on these parameters the expert software identifies the type of the accident and also provides the user with appropriate references (past analyses and other documentation of such an accident). The expert software is to be used as a support tool by an expert team that forms in case of an emergency at Slovenian Nuclear Safety Administration (SNSA) with the task to determine the cause of the accident, its most probable scenario and the source term. The expert software should provide initial identification of the event, while the final one is still to be made after appropriate assessment of the event by the expert group considering possibility of non-typical events, multiple causes, initial conditions, influences of operators' actions etc. The expert software can be also used as an educational/training tool and even as a simple database of available accident analyses. (author)

Experimental results from containment piping bellows subjected to severe accident conditions: Results from bellows tested in corroded conditions. Volume 2

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1995-10-01

Bellows are an integral part of the containment pressure boundary in nuclear power plants. They are used at piping penetrations to allow relative movement between piping and the containment wall, while minimizing the load imposed on the piping and wall. Piping bellows are primarily used in steel containments; however, they have received limited use in some concrete (reinforced and prestressed) containments. In a severe accident they may be subjected to pressure and temperature conditions that exceed the design values, along with a combination of axial and lateral deflections. A test program to determine the leak-tight capacity of containment penetration bellows is being conducted at Sandia National Laboratories under the sponsorship of the US Nuclear Regulatory Commission. Several different bellows geometries, representative of actual containment bellows, have been subjected to extreme deflections along with pressure and temperature loads. The bellows geometries and loading conditions are described along with the testing apparatus and procedures. A total of nineteen bellows have been tested. Thirteen bellows were tested in ''like-new'' condition (results reported in Volume 1), and six were tested in a corroded condition. The tests showed that bellows in ''like-new'' condition are capable of withstanding relatively large deformations, up to, or near, the point of full compression or elongation, before developing leakage, while those in a corroded condition did not perform as well, depending on the amount of corrosion. The corroded bellows test program and results are presented in this report

Estimation of cost per severe accident for improvement of accident protection and consequence mitigation strategies

International Nuclear Information System (INIS)

Silva, Kampanart; Ishiwatari, Yuki; Takahara, Shogo

2013-01-01

To assess the complex situations regarding the severe accidents such as what observed in Fukushima Accident, not only radiation protection aspects but also relevant aspects: health, environmental, economic and societal aspects; must be all included into the consequence assessment. In this study, the authors introduce the “cost per severe accident” as an index to analyze the consequences of severe accidents comprehensively. The cost per severe accident consists of various costs and consequences converted into monetary values. For the purpose of improvement of the accident protection and consequence mitigation strategies, the costs needed to introduce the protective actions, and health and psychological consequences are included in the present study. The evaluations of these costs and consequences were made based on the systematic consequence analysis using level 2 and 3 probabilistic safety assessment (PSA) codes. The accident sequences used in this analysis were taken from the results of level 2 seismic PSA of a virtual 1,100 MWe BWR-5. The doses to the public and the number of people affected were calculated using the level 3 PSA code OSCAAR of Japan Atomic Energy Agency (JAEA). The calculations have been made for 248 meteorological sequences, and the outputs are given as expectation values for various meteorological conditions. Using these outputs, the cost per severe accident is calculated based on the open documents on the Fukushima Accident regarding the cost of protective actions and compensations for psychological harms. Finally, optimized accident protection and consequence mitigation strategies are recommended taking into account the various aspects comprehensively using the cost per severe accident. The authors must emphasize that the aim is not to estimate the accident cost itself but to extend the scope of “risk-informed decision making” for continuous safety improvements of nuclear energy. (author)

Accident Sequence Precursor Analysis for SGTR by Using Dynamic PSA Approach

International Nuclear Information System (INIS)

Lee, Han Sul; Heo, Gyun Young; Kim, Tae Wan

2016-01-01

In order to address this issue, this study suggests the sequence tree model to analyze accident sequence systematically. Using the sequence tree model, all possible scenarios which need a specific safety action to prevent the core damage can be identified and success conditions of safety action under complicated situation such as combined accident will be also identified. Sequence tree is branch model to divide plant condition considering the plant dynamics. Since sequence tree model can reflect the plant dynamics, arising from interaction of different accident timing and plant condition and from the interaction between the operator action, mitigation system, and the indicators for operation, sequence tree model can be used to develop the dynamic event tree model easily. Target safety action for this study is a feed-and-bleed (F and B) operation. A F and B operation directly cools down the reactor cooling system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. In this study, a TLOFW accident and a TLOFW accident with LOCA were the target accidents. Based on the conventional PSA model and indicators, the sequence tree model for a TLOFW accident was developed. Based on the results of a sampling analysis and data from the conventional PSA model, the CDF caused by Sequence no. 26 can be realistically estimated. For a TLOFW accident with LOCA, second accident timings were categorized according to plant condition. Indicators were selected as branch point using the flow chart and tables, and a corresponding sequence tree model was developed. If sampling analysis is performed, practical accident sequences can be identified based on the sequence analysis. If a realistic distribution for the variables can be obtained for sampling analysis, much more realistic accident sequences can be described. Moreover, if the initiating event frequency under a combined accident can be quantified, the sequence tree model

The behavior of a container for UF6 under accident conditions

International Nuclear Information System (INIS)

Andreuccetti, P.; Aquaro, D.; Forasassi, G.

1987-01-01

Transport of uranium hexafluoride during the different phases of the fuel cycle is carried out using containers of various types that must meet the safety requirements provided for in the specific international regulations for this area. Qualification of the behavior of the 30B cylinder and its respective overpack under reference accident conditions for the purpose of design and utilization of such containers is currently a subject of interest on an international level, since it is being widely used in a number of countries. To contribute to this qualification process, a relatively complex research program was defined and developed, including, among other things, drop tests from 9 m on to an unyielding target, drop tests from a height of 1 m on to a cylindrical bar, and thermal tests in a furnace, all of which were carried out on two complete specimens of the same container with a simulated load. For analysis of the damage a series of leak tests and a water immersion test were developed to analyze the damage to the two specimens mentioned above and to a container of reduced dimensions designed for this purpose and equipped to reproduce conditions similar to the real conditions inside the container under investigation. Evaluation of the heat exchange conditions that could exist in the container given real contents of uranium hexafluoride was also conducted using a series of calculations carried out with the computer code TRUMP. The results of the different types of experiments and calculations performed and presented in detail in the present study have made it possible to draw useful conclusions for practical evaluation of the reliability of the container under investigation, also in view of the intended goal of container qualification as per the existing regulations for transport of radioactive material. 21 refs., 44 figs., 3 tabs

Preliminary report about nuclear accident of Chernobylsk reactor

International Nuclear Information System (INIS)

Oliveira, A.R. de.

1986-07-01

The preliminary report of nuclear accident at Chernobyl, in URSS is presented. The Chernobyl site is located geographically and the RBMK type reactors - initials of russian words which mean high power pressure tube reactors are described. The conditions of reactor operation in beginning of accident, the events which lead to reactor destruction, the means to finish the fire, the measurements adopted by Russian in the accident location, the estimative of radioactive wastes, the meteorological conditions during the accident, the victims and medical assistence, the sanitary aspects and consequences for population, the evaluation of radiation doses received at small and medium distance and the estimative of reffered doses by population attained are presented. The official communication of Russian Minister Council and the declaration of IAEA general manager during a collective interview in Moscou are annexed. (M.C.K.) [pt

Experimental data report for Test TS-1 Reactivity Initiated Accident Test in NSRR with pre-irradiated BWR fuel rod

International Nuclear Information System (INIS)

Nakamura, Takehiko; Yoshinaga, Makio; Sobajima, Makoto; Fujishiro, Toshio; Horiki, Ohichiro; Yamahara, Takeshi; Ichihashi, Yoshinori; Kikuchi, Teruo

1992-01-01

This report presents experimental data for Test TS-1 which was the first in a series of tests, simulating Reactivity Initiated Accident (RIA) conditions using pre-irradiated BWR fuel rods, performed in the Nuclear Safety Research Reactor (NSRR) in October, 1989. Test fuel rod used in the Test TS-1 was a short-sized BWR (7 x 7) type rod which was fabricated from a commercial rod provided from Tsuruga Unit 1 power reactor. The fuel had an initial enrichment of 2.79 % and burnup of 21.3 GWd/t (bundle average). Pulse irradiation was performed at a condition of stagnant water cooling, atmospheric pressure and ambient temperature using a newly developed double container-type capsule. Energy deposition of the rod in this test was evaluated to be about 61 cal/g·fuel (55 cal/g·fuel in peak fuel enthalpy) and no fuel failure was observed. Descriptions on test conditions, test procedures, fuel burnup measurements, transient behavior of the test rod during pulse irradiation and results of post pulse irradiation examinations are contained in this report. (author)

Urticária Urticaria

Directory of Open Access Journals (Sweden)

Paulo Ricardo Criado

2005-12-01

Full Text Available A urticária apresenta-se com diversas formas clínicas e causas distintas. Constitui uma das dermatoses mais freqüentes: 15% a 20% da população têm pelo menos um episódio agudo da doença em sua vida, resultando em percentual que varia de um a 2% dos atendimentos nas especialidades de Dermatologia e Alergologia. A urticária é classificada do ponto de vista de duração da evolução temporal em aguda (inferior a seis semanas ou crônica (superior a seis semanas. O tratamento da urticária pode compreender medidas não farmacológicas e intervenções medicamentosas, as quais são agrupadas em tratamentos de primeira (anti-histamínicos, segunda (corticosteróides e antileucotrienos e terceira linha (medicamentos imunomoduladores. As medidas terapêuticas de segunda e terceira linha apresentam maiores efeitos adversos, devendo ser reservadas aos doentes que não apresentaram controle da doença com os de primeira linha, ou àqueles a respeito dos quais não é possível estabelecer uma etiologia, tal como nas urticárias auto-imunes.Urticaria has diverse clinical presentations and causes. It is one of the most frequent dermatological conditions: 15% to 20% of population has at least one acute eruption during their lifetime, resulting in 1% to 2% of dermatological and allergological visits. Urticaria is classified based on its temporal evolution as acute (less than 6 weeks or chronic (more than 6 weeks. Management strategies may involve non-pharmacological measures and drug interventions, which are grouped into first- (antihistamines, second- (corticosteroids and anti-leukotrienes and third-line therapies (immunomodulators. Stronger, but potentially riskier, second- and third-line management may be justified for patients who do not respond to first-line therapy, or whenever a specific etiology cannot be determined, such as in autoimmune urticaria.

Thermal and hydraulic behaviour of CANDU cores under severe accident conditions - final report. Vol. 1

International Nuclear Information System (INIS)

Rogers, J.T.

1984-06-01

This report gives the results of a study of the thermo-hydraulic aspects of severe accident sequences in CANDU reactors. The accident sequences considered are the loss of the moderator cooling system and the loss of the moderator heat sink, each following a large loss-of-coolant accident accompanied by loss of emergency coolant injection. Factors considered include expulsion and boil-off of the moderator, uncovery, overheating and disintegration of the fuel channels, quenching of channel debris, re-heating of channel debris following complete moderator expulsion, formation and possible boiling of a molten pool of core debris and the effectiveness of the cooling of the calandria wall by the shield tank water during the accident sequences. The effects of these accident sequences on the reactor containment are also considered. Results show that there would be no gross melting of fuel during moderator expulsion from the calandria, and for a considerable time thereafter, as quenched core debris re-heats. Core melting would not begin until about 135 minutes after accident initiation in a loss of the moderator cooling system and until about 30 minutes in a loss of the moderator heat sink. Eventually, a pool of molten material would form in the bottom of the calandria, which may or may not boil, depending on property values. In all cases, the molten core would be contained within the calandria, as long as the shield tank water cooling system remains operational. Finally, in the period from 8 to 50 hours after the initiation of the accident, the molten core would re-solidify within the calandria. There would be no consequent damage to containment resulting from these accident sequences, nor would there be a significant increase in fission product releases from containment above those that would otherwise occur in a dual failure LOCA plus LOECI

Conditions for oxygen-deficient combustion during accidents with severe core concrete thermal attack

International Nuclear Information System (INIS)

Luangdilok, W.; Elicson, G.T.; Berger, W.E. Jr.

1993-01-01

This paper addresses the interactions between MCCI (molten core-concrete interactions)-induced offgas releases, mostly the combustible gases, natural circulation between the cavity and the lower containment based on recent research developments in the area of mixed convection flow (Epstein, et al., 1989; Epstein, 1988; Epstein, 1992) between compartments, and their effects on combustion in PWR containments during prolonged severe accidents. Specifically, large dry PWR containments undergoing severe core-concrete attack during station blackouts where the containment atmosphere is expected to be inerted are objects of this analysis. The purpose of this paper, given the conditions that oxygen can be brought to the cavity, is to demonstrate that consumption of most oxygen present in the containment can be achieved in a reasonable time scale assuming that combustion is not subject to flammability limits due to the high cavity temperatures. The conditions for cavity combustion depend on several factors including good gas flowpaths between the cavity and other containment regions, and combustion processes within the cavity with the hot debris acting as the ignition source

Monitoring severe accidents using AI techniques

Energy Technology Data Exchange (ETDEWEB)

No, Young Gyu; Ahn, Kwang Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Ju Hyun; Na, Man Gyun [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of); Lim, Dong Hyuk [Korea Institute of Nuclear Nonproliferation and Control, Daejon (Korea, Republic of)

2012-05-15

After the Fukushima nuclear accident in 2011, there has been increasing concern regarding severe accidents in nuclear facilities. Severe accident scenarios are difficult for operators to monitor and identify. Therefore, accurate prediction of a severe accident is important in order to manage it appropriately in the unfavorable conditions. In this study, artificial intelligence (AI) techniques, such as support vector classification (SVC), probabilistic neural network (PNN), group method of data handling (GMDH), and fuzzy neural network (FNN), were used to monitor the major transient scenarios of a severe accident caused by three different initiating events, the hot-leg loss of coolant accident (LOCA), the cold-leg LOCA, and the steam generator tube rupture in pressurized water reactors (PWRs). The SVC and PNN models were used for the event classification. The GMDH and FNN models were employed to accurately predict the important timing representing severe accident scenarios. In addition, in order to verify the proposed algorithm, data from a number of numerical simulations were required in order to train the AI techniques due to the shortage of real LOCA data. The data was acquired by performing simulations using the MAAP4 code. The prediction accuracy of the three types of initiating events was sufficiently high to predict severe accident scenarios. Therefore, the AI techniques can be applied successfully in the identification and monitoring of severe accident scenarios in real PWRs.

Monitoring severe accidents using AI techniques

International Nuclear Information System (INIS)

No, Young Gyu; Ahn, Kwang Il; Kim, Ju Hyun; Na, Man Gyun; Lim, Dong Hyuk

2012-01-01

After the Fukushima nuclear accident in 2011, there has been increasing concern regarding severe accidents in nuclear facilities. Severe accident scenarios are difficult for operators to monitor and identify. Therefore, accurate prediction of a severe accident is important in order to manage it appropriately in the unfavorable conditions. In this study, artificial intelligence (AI) techniques, such as support vector classification (SVC), probabilistic neural network (PNN), group method of data handling (GMDH), and fuzzy neural network (FNN), were used to monitor the major transient scenarios of a severe accident caused by three different initiating events, the hot-leg loss of coolant accident (LOCA), the cold-leg LOCA, and the steam generator tube rupture in pressurized water reactors (PWRs). The SVC and PNN models were used for the event classification. The GMDH and FNN models were employed to accurately predict the important timing representing severe accident scenarios. In addition, in order to verify the proposed algorithm, data from a number of numerical simulations were required in order to train the AI techniques due to the shortage of real LOCA data. The data was acquired by performing simulations using the MAAP4 code. The prediction accuracy of the three types of initiating events was sufficiently high to predict severe accident scenarios. Therefore, the AI techniques can be applied successfully in the identification and monitoring of severe accident scenarios in real PWRs.

Fuel behavior and fission product release under HTGR accident conditions

International Nuclear Information System (INIS)

Fukuda, K.; Hayashi, K.; Shiba, K.

1990-01-01

In early 1989 a final decision was made over construction of a 30 MWth HTGR called the High Temperature Engineering Test Reactor, HTTR, in Japan in order to utilize it for high temperature gas engineering tests and various nuclear material tests. The HTTR fuel is a pin-in-block type fuel element which is composed of a hexagonal graphite block with dimension of 580 mm in length and 360 mm in face-to-face distance and about 30 of the fuel rods inserted into the coolant channels drilled in the block. The TRISO coated fuel particles for HTTR are incorporated with graphite powder and phenol resin into the fuel compacts, 19 of which are encased into a graphite sleeve as a fuel rod. It is necessary for the HTTR licensing to prove the fuel stability under predicted accidents related to the high temperature events. Therefore, the release of the fission products and the fuel failure have been investigated in the irradiation---and the heating experiments simulating these conditions at JAERI. This report describes the HTTR fuel behavior at extreme temperature, made clear in these experiments

Passive depressurization accident management strategy for boiling water reactors

International Nuclear Information System (INIS)

Liu, Maolong; Erkan, Nejdet; Ishiwatari, Yuki; Okamoto, Koji

2015-01-01

Highlights: • We proposed two passive depressurization systems for BWR severe accident management. • Sensitivity analysis of the passive depressurization systems with different leakage area. • Passive depressurization strategies can prevent direct containment heating. - Abstract: According to the current severe accident management guidance, operators are required to depressurize the reactor coolant system to prevent or mitigate the effects of direct containment heating using the safety/relief valves. During the course of a severe accident, the pressure boundary might fail prematurely, resulting in a rapid depressurization of the reactor cooling system before the startup of SRV operation. In this study, we demonstrated that a passive depressurization system could be used as a severe accident management tool under the severe accident conditions to depressurize the reactor coolant system and to prevent an additional devastating sequence of events and direct containment heating. The sensitivity analysis performed with SAMPSON code also demonstrated that the passive depressurization system with an optimized leakage area and failure condition is more efficient in managing a severe accident

Passive depressurization accident management strategy for boiling water reactors

Energy Technology Data Exchange (ETDEWEB)

Liu, Maolong, E-mail: liuml@vis.t.u-tokyo.ac.jp [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo (Japan); Erkan, Nejdet [Nuclear Professional School, School of Engineering, The University of Tokyo (Japan); Ishiwatari, Yuki [Department of Nuclear Engineering and Management, School of Engineering, The University of Tokyo (Japan); Hitachi-GE Nuclear Energy, Ltd. (Japan); Okamoto, Koji [Nuclear Professional School, School of Engineering, The University of Tokyo (Japan)

2015-04-01

Highlights: • We proposed two passive depressurization systems for BWR severe accident management. • Sensitivity analysis of the passive depressurization systems with different leakage area. • Passive depressurization strategies can prevent direct containment heating. - Abstract: According to the current severe accident management guidance, operators are required to depressurize the reactor coolant system to prevent or mitigate the effects of direct containment heating using the safety/relief valves. During the course of a severe accident, the pressure boundary might fail prematurely, resulting in a rapid depressurization of the reactor cooling system before the startup of SRV operation. In this study, we demonstrated that a passive depressurization system could be used as a severe accident management tool under the severe accident conditions to depressurize the reactor coolant system and to prevent an additional devastating sequence of events and direct containment heating. The sensitivity analysis performed with SAMPSON code also demonstrated that the passive depressurization system with an optimized leakage area and failure condition is more efficient in managing a severe accident.

Chemical factors affecting fission product transport in severe LMFBR accidents

International Nuclear Information System (INIS)

Wichner, R.P.; Jolley, R.L.; Gat, U.; Rodgers, B.R.

1984-10-01

This study was performed as a part of a larger evaluation effort on LMFBR accident, source-term estimation. Purpose was to provide basic chemical information regarding fission product, sodium coolant, and structural material interactions required to perform estimation of fission product transport under LMFBR accident conditions. Emphasis was placed on conditions within the reactor vessel; containment vessel conditions are discussed only briefly

Feasibility study of superconducting power cables for DC electric railway feeding systems in view of thermal condition at short circuit accident

Science.gov (United States)

Kumagai, Daisuke; Ohsaki, Hiroyuki; Tomita, Masaru

2016-12-01

A superconducting power cable has merits of a high power transmission capacity, transmission losses reduction, a compactness, etc., therefore, we have been studying the feasibility of applying superconducting power cables to DC electric railway feeding systems. However, a superconducting power cable is required to be cooled down and kept at a very low temperature, so it is important to reveal its thermal and cooling characteristics. In this study, electric circuit analysis models of the system and thermal analysis models of superconducting cables were constructed and the system behaviors were simulated. We analyzed the heat generation by a short circuit accident and transient temperature distribution of the cable to estimate the value of temperature rise and the time required from the accident. From these results, we discussed a feasibility of superconducting cables for DC electric railway feeding systems. The results showed that the short circuit accident had little impact on the thermal condition of a superconducting cable in the installed system.

Use of accident experience in developing criteria for teleoperator equipment

International Nuclear Information System (INIS)

Vallario, E.J.; Selby, J.M.

1985-10-01

The 1961 SL-1 reactor accident in Idaho and the Recuplex accident at Hanford are reviewed to identify problems common to emergency situations, lessons learned from accidents, criteria for emergency equipment, and recommendations for using robotics to solve problems during emergencies. Teleoperator equipment could be used to assess the extent of the damage and the condition of the reactor, retrieve dosimeters, evacuate and treat accident victims, clean up debris and decontaminate accident areas. 2 refs., 9 figs

Response of a DSNP pressurizer model under accident conditions

International Nuclear Information System (INIS)

Saphier, D.; Kallfelz, J.; Belblidia, L.

1986-01-01

Recently a new pressurizer model was developed for the DSNP simulation language. The model was connected to a simulation of the Trojan pressurized water reactor (PWR) and tested by simulating a loss-of-off-site power (LOSP) anticipated transient without scram. The results compare well to a similar study performed using the RELAP code. The pressurizer model and its response to the LOSP accident are presented

Post-test investigation result on the WWER-1000 fuel tested under severe accident conditions

International Nuclear Information System (INIS)

Goryachev, A.; Shtuckert, Yu.; Zwir, E.; Stupina, L.

1996-01-01

The model bundle of WWER-type were tested under SFD condition in the out-of-pile CORA installation. The objective of the test was to provide an information on the WWER-type fuel bundles behaviour under severe fuel damage accident conditions. Also it was assumed to compare the WWER-type bundle damage mechanisms with these experienced in the PWR-type bundle tests with aim to confirm a possibility to use the various code systems, worked our for PWR as applied to WWER. In order to ensure the possibility of the comparison of the calculated core degradation parameters with the real state of the tested bundle, some parameters have been measured on the bundle cross-sections under examination. Quantitative parameters of the bundle degradation have been evaluated by digital image processing of the bundle cross-sections. The obtained results are shown together with corresponding results obtained by the other participants of this investigation. (author). 3 refs, 13 figs

Benchmarking MARS (accident management software) with the Browns Ferry fire

International Nuclear Information System (INIS)

Dawson, S.M.; Liu, L.Y.; Raines, J.C.

1992-01-01

The MAAP Accident Response System (MARS) is a userfriendly computer software developed to provide management and engineering staff with the most needed insights, during actual or simulated accidents, of the current and future conditions of the plant based on current plant data and its trends. To demonstrate the reliability of the MARS code in simulatng a plant transient, MARS is being benchmarked with the available reactor pressure vessel (RPV) pressure and level data from the Browns Ferry fire. The MRS software uses the Modular Accident Analysis Program (MAAP) code as its basis to calculate plant response under accident conditions. MARS uses a limited set of plant data to initialize and track the accidnt progression. To perform this benchmark, a simulated set of plant data was constructed based on actual report data containing the information necessary to initialize MARS and keep track of plant system status throughout the accident progression. The initial Browns Ferry fire data were produced by performing a MAAP run to simulate the accident. The remaining accident simulation used actual plant data

Severe accident recriticality analyses (SARA)

DEFF Research Database (Denmark)

Frid, W.; Højerup, C.F.; Lindholm, I.

2001-01-01

with all three codes. The core initial and boundary conditions prior to recriticality have been studied with the severe accident codes SCDAP/RELAP5, MELCOR and MAAP4. The results of the analyses show that all three codes predict recriticality-both super-prompt power bursts and quasi steady-state power......Recriticality in a BWR during reflooding of an overheated partly degraded core, i.e. with relocated control rods, has been studied for a total loss of electric power accident scenario. In order to assess the impact of recriticality on reactor safety, including accident management strategies......, which results in large energy deposition in the fuel during power burst in some accident scenarios. The highest value, 418 cal g(-1), was obtained with SIMULATE-3K for an Oskarshamn 3 case with reflooding rate of 2000 kg s(-1). In most cases, however, the predicted energy deposition was smaller, below...

Experiments to evaluate behavior of containment piping bellows under severe accident conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1993-01-01

Bellows are an integral part of the containment pressure boundary in nuclear power plants. They are used at piping penetrations to allow relative movement between piping and the containment wall. In a severe accident they may be subjected to high pressure and temperature, and a combination of axial and lateral deflections. A test program to determine the leak-tight capacity of containment penetration bellows is being conducted at Sandia National Laboratories, Albuquerque, New Mexico. Several different bellows geometries, representative of actual containment bellows, are being subjected to extreme deflections along with pressure and temperature loads. The bellows geometries and loading conditions are described along with the testing apparatus and procedures. A total of thirteen tests have been conducted. The tests showed that withstanding relatively large bellows are capable of deformations, up to, or near, the point of full compression before developing leakage. The test data is presented and discussed

História e memória: a soldadura da imaginação

Directory of Open Access Journals (Sweden)

Brum, Rosemary Fritsch

2006-01-01

Full Text Available Este artigo explora possibilidades em história oral, o desenvolvimento na contemporaneidade das ciências cognitivas e sua aproximação com histórias curtas. Essas direções podem ser fertilizadas pelo pesquisador nos estudos da memória, da narrativa e da oralidade

Detection device for off-gas system accidents

International Nuclear Information System (INIS)

Kubota, Ryuji; Tsuruoka, Ryozo; Yamanari, Shozo.

1984-01-01

Purpose: To rapidly isolate the off-gas system by detecting the off-gas system failure accident in a short time. Constitution: Radiation monitors are disposed to ducts connecting an exhaust gas area and an air conditioning system as a portion of a turbine building. The ducts are disposed independently such that they ventilate only the atmosphere in the exhaust gas area and do not mix the atmosphere in the turbine building. Since radioactivity issued upon off-gas accidents to the exhaust gas area is sucked to the duct, it can be detected by radiation detection monitors in a short time after the accident. Further, since the operator judges it as the off-gas system accident, the off-gas system can be isolated in a short time after the accident. (Moriyama, K.)

Thermal hydraulic analysis of aggressive secondary cooldown in a small break loss of coolant accident with a total loss of high pressure safety injection

International Nuclear Information System (INIS)

Han, Seok Jung; Lim, Ho Gon; Yang, Joon Eon

2003-03-01

Recently, Probabilistic Safety Assessment (PSA) has being applied to various fields as a basic technique of Risk-Informed Applications (RIA). The present study focuses on detailed thermal hydraulic analyses for major accident sequences and success criteria to support a development of PSA model using RIA for Korea Standard Nuclear Power plant (KSNP). The primary purpose of the present study in this year is to evaluate the success cri-teria of Aggressive Secondary Cooldown (ASC) in a Small Size Loss Of Coolant Accident (SBLOCA) without HPSI and to enhance the understanding of related thermal hydraulic behavior and phenomena. An effort was made to evaluate the system success criteria and a mission time for the recovery action by an operator to prevent the core damage for that accident scenario. The accident scenario for KSNP was a 2 inch coldleg break LOCA with a total loss of High Pressure Safety Injection (HPSI) and 1/2 Low Pressure Safety Injection (LPSI) available and perform-ing ASC limited by 55.6 .deg. C/hr (100 .deg. F/hr) cooldown rate at 15 minute after reactor trip. It successively reached the LPSI condition for about 1.5hr after starting the ASC operation with the Peak Cladding Temperature (PCT) of the hottest rod below the core damage criteria of 1204.4 .deg. C (2200 .deg. F). Sensitivity studies were performed for (1) cool-ant average temperature parameters, (2) ASC operation control method, (3) operation start time, (4) 1 inch break size. The present analysis identified thermal hydraulic phenomena and parameters affecting on the behavior, which consist of coolant break flow and inventory, parameters governing secondary heat removal, ASC operation control method, and its reference temperature parameters. In the present study, more relaxed success criteria than the previous PSA for KSNP could be generated under an assumption that an operator should maintain the ade-quate ASC operation. However, it is necessary to evaluate the uncertainties arisen from the

Post-accident monitoring systems in Prototype Fast Breeder Reactor

International Nuclear Information System (INIS)

Suriya Murthy, N.; Sivasailanathan, Vidhya; Ananth, Allu; Roy, Kallol

2018-01-01

PFBR is a 500 MW(e) MOX fueled and sodium cooled fast reactor (SFR) under advanced stage of commissioning at Kalpakkam. Currently, the main vessel is preheated and sodium has been charged into two secondary loops that are operated in recirculation mode. In order to characterize the radiation field and contamination, the workplace monitoring is undertaken using installed monitors that are commissioned and made operational. This helps to ensure radiological protection during normal operating conditions. On the other hand, radiological monitoring in emergency conditions is quite different. For undertaking the mitigative accident management, a set of specialized nuclear instruments called post-accident monitoring systems (PAMS) which include radiation monitors are stipulated. The Fukushima Daiichi accident emphasized the importance and need for reliable accident monitoring instrumentation to indicate the safety functions during the progression and aftermath of accident in NPP. In PFBR, the PAMS are integrated with other monitoring systems in design stage itself to manage the measurements and indicating the safety functions for implementing EOP and SAMG

Behavior of an improved Zr fuel cladding with oxidation resistant coating under loss-of-coolant accident conditions

Energy Technology Data Exchange (ETDEWEB)

Park, Dong Jun, E-mail: pdj@kaeri.re.kr; Kim, Hyun Gil; Jung, Yang Il; Park, Jung Hwan; Yang, Jae Ho; Koo, Yang Hyun

2016-12-15

This study investigates protective coatings for improving the high temperature oxidation resistance of Zr fuel claddings for light water nuclear reactors. FeCrAl alloy and Cr layers were deposited onto Zr plates and tubes using cold spraying. For the FeCrAl/Zr system, a Mo layer was introduced between the FeCrAl coating and the Zr matrix to prevent inter-diffusion at high temperatures. Both the FeCrAl and Cr coatings improved the oxidation resistance compared to that of the uncoated Zr alloy when exposed to a steam environment at 1200 °C. The ballooning behavior and mechanical properties of the coated cladding samples were studied under simulated loss-of-coolant accident conditions. The coated samples showed higher burst temperatures, lower circumferential strain, and smaller rupture openings compared to the uncoated Zr. Although 4-point bend tests of the coated samples showed a small increase in the maximum load, ring compression tests of a sectioned sample showed increased ductility. - Highlights: • Cr and FeCrAl were coated onto Zr fuel cladding for light water nuclear reactors. • Mo layer between FeCrAl and Zr prevented inter-diffusion at high temperatures. • Coated claddings were tested under loss-of-cooling accident conditions. • Coating improved high-temperature oxidation resistance and mechanical properties.

Regulatory impact of nuclear reactor accident source term assumptions. Technical report

International Nuclear Information System (INIS)

Pasedag, W.F.; Blond, R.M.; Jankowski, M.W.

1981-06-01

This report addresses the reactor accident source term implications on accident evaluations, regulations and regulatory requirements, engineered safety features, emergency planning, probabilistic risk assessment, and licensing practice. Assessment of the impact of source term modifications and evaluation of the effects in Design Basis Accident analyses, assuming a change of the chemical form of iodine from elemental to cesium iodide, has been provided. Engineered safety features used in current LWR designs are found to be effective for all postulated combinations of iodine source terms under DBA conditions. In terms of potential accident consequences, it is not expected that the difference in chemical form between elemental iodine and cesium iodide would be significant. In order to account for the current information on source terms, a spectrum of accident scenerios is discussed to realistically estimate the source terms resulting from a range of potential accident conditions

Accident analysis in nuclear power plants

International Nuclear Information System (INIS)

Silva, D.E. da

1981-01-01

The way the philosophy of Safety in Depth can be verified through the analysis of simulated accidents is shown. This can be achieved by verifying that the integrity of the protection barriers against the release of radioactivity to the environment is preserved even during accident conditions. The simulation of LOCA is focalized as an example, including a study about the associated environmental radiological consequences. (Author) [pt

Fuel cladding behavior under rapid loading conditions

Science.gov (United States)

Yueh, K.; Karlsson, J.; Stjärnsäter, J.; Schrire, D.; Ledergerber, G.; Munoz-Reja, C.; Hallstadius, L.

2016-02-01

A modified burst test (MBT) was used in an extensive test program to characterize fuel cladding failure behavior under rapid loading conditions. The MBT differs from a normal burst test with the use of a driver tube to simulate the expansion of a fuel pellet, thereby producing a partial strain driven deformation condition similar to that of a fuel pellet expansion in a reactivity insertion accident (RIA). A piston/cylinder assembly was used to pressurize the driver tube. By controlling the speed and distance the piston travels the loading rate and degree of sample deformation could be controlled. The use of a driver tube with a machined gauge section localizes deformation and allows for continuous monitoring of the test sample diameter change at the location of maximum hoop strain, during each test. Cladding samples from five irradiated fuel rods were tested between 296 and 553 K and loading rates from 1.5 to 3.5/s. The test rods included variations of Zircaloy-2 with different liners and ZIRLO, ranging in burn-up from 41 to 74 GWd/MTU. The test results show cladding ductility is strongly temperature and loading rate dependent. Zircaloy-2 cladding ductility degradation due to operational hydrogen pickup started to recover at approximately 358 K for test condition used in the study. This recovery temperature is strongly loading rate dependent. At 373 K, ductility recovery was small for loading rates less than 8 ms equivalent RIA pulse width, but longer than 8 ms the ductility recovery increased exponentially with increasing pulse width, consistent with literature observations of loading rate dependent brittle-to-ductile (BTD) transition temperature. The cladding ductility was also observed to be strongly loading rate/pulse width dependent for BWR cladding below the BTD temperature and Pressurized Water Reactor (PWR) cladding at both 296 and 553 K.

Factors contributing to young moped rider accidents in Denmark.

Science.gov (United States)

Møller, Mette; Haustein, Sonja

2016-02-01

Young road users still constitute a high-risk group with regard to road traffic accidents. The crash rate of a moped is four times greater than that of a motorcycle, and the likelihood of being injured in a road traffic accident is 10-20 times higher among moped riders compared to car drivers. Nevertheless, research on the behaviour and accident involvement of young moped riders remains sparse. Based on analysis of 128 accident protocols, the purpose of this study was to increase knowledge about moped accidents. The study was performed in Denmark involving riders aged 16 or 17. A distinction was made between accident factors related to (1) the road and its surroundings, (2) the vehicle, and (3) the reported behaviour and condition of the road user. Thirteen accident factors were identified with the majority concerning the reported behaviour and condition of the road user. The average number of accident factors assigned per accident was 2.7. Riding speed was assigned in 45% of the accidents which made it the most frequently assigned factor on the part of the moped rider followed by attention errors (42%), a tuned up moped (29%) and position on the road (14%). For the other parties involved, attention error (52%) was the most frequently assigned accident factor. The majority (78%) of the accidents involved road rule breaching on the part of the moped rider. The results indicate that preventive measures should aim to eliminate violations and increase anticipatory skills among moped riders and awareness of mopeds among other road users. Due to their young age the effect of such measures could be enhanced by infrastructural measures facilitating safe interaction between mopeds and other road users. Copyright © 2015 Elsevier Ltd. All rights reserved.

Behaviour of rock-like oxide fuels under reactivity-initiated accident conditions

International Nuclear Information System (INIS)

Kazuyuki, Kusagaya; Takehiko, Nakamura; Makio, Yoshinaga; Hiroshi, Akie; Toshiyuki, Yamashita; Hiroshi, Uetsuka

2002-01-01

Pulse irradiation tests of three types of un-irradiated rock-like oxide (ROX) fuel - yttria-stabilised zirconia (YSZ) single phase, YSZ and spinel (MgAl 2 O 4 ) homogeneous mixture and particle-dispersed YSZ/spinel - were conducted in the Nuclear Safety Research Reactor to investigate the fuel behaviour under reactivity-initiated accident conditions. The ROX fuels failed at fuel volumetric enthalpies above 10 GJ/m 3 , which was comparable to that of un-irradiated UO 2 fuel. The failure mode of the ROX fuels, however, was quite different from that of the UO 2 fuel. The ROX fuels failed with fuel pellet melting and a part of the molten fuel was released out to the surrounding coolant water. In spite of the release, no significant mechanical energy generation due to fuel/coolant thermal interaction was observed in the tested enthalpy range below∼12 GJ/m 3 . The YSZ type and homogenous YSZ/spinel type ROX fuels failed by cladding burst when their temperatures peaked, while the particle-dispersed YSZ/spinel type ROX fuel seemed to have failed by cladding local melting. (author)

Traffic dynamics around weaving section influenced by accident: Cellular automata approach

Science.gov (United States)

Kong, Lin-Peng; Li, Xin-Gang; Lam, William H. K.

2015-07-01

The weaving section, as a typical bottleneck, is one source of vehicle conflicts and an accident-prone area. Traffic accident will block lanes and the road capacity will be reduced. Several models have been established to study the dynamics around traffic bottlenecks. However, little attention has been paid to study the complex traffic dynamics influenced by the combined effects of bottleneck and accident. This paper presents a cellular automaton model to characterize accident-induced traffic behavior around the weaving section. Some effective control measures are proposed and verified for traffic management under accident condition. The total flux as a function of inflow rates, the phase diagrams, the spatial-temporal diagrams, and the density and velocity profiles are presented to analyze the impact of accident. It was shown that the proposed control measures for weaving traffic can improve the capacity of weaving section under both normal and accident conditions; the accidents occurring on median lane in the weaving section are more inclined to cause traffic jam and reduce road capacity; the capacity of weaving section will be greatly reduced when the accident happens downstream the weaving section.

TASAC a computer program for thermal analysis of severe accident conditions. Version 3/01, Dec 1991. Model description and user`s guide

Energy Technology Data Exchange (ETDEWEB)

Stempniewicz, M; Marks, P; Salwa, K

1992-06-01

TASAC (Thermal Analysis of Severe Accident Conditions) is computer code developed in the Institute of Atomic Energy written in FORTRAN 77 for the digital computer analysis of PWR rod bundle behaviour during severe accident conditions. The code has the ability to model an early stage of core degradation including heat transfer inside the rods, convective and radiative heat exchange as well as cladding interactions with coolant and fuel, hydrogen generation, melting, relocations and refreezing of fuel rod materials with dissolution of UO{sub 2} and ZrO{sub 2} in liquid phase. The code was applied for the simulation of International Standard Problem number 28, performed on PHEBUS test facility. This report contains the program physical models description, detailed description of input data requirements and results of code verification. The main directions for future TASAC code development are formulated. (author). 20 refs, 39 figs, 4 tabs.

CEA studies on advanced nuclear fuel claddings for enhanced accident tolerant LWRs fuel (LOCA and beyond LOCA conditions)

International Nuclear Information System (INIS)

Brachet, J.C.; Lorrette, C.; Michaux, A.; Sauder, C.; Idarraga-Trujillo, I.; Le Saux, M.; Le Flem, M.; Schuster, F.; Billard, A.; Monsifrot, E.; Torres, E.; Rebillat, F.; Bischoff, J.; Ambard, A.

2015-01-01

This paper gives an overview of CEA studies on advanced nuclear fuel claddings for enhanced Accident Tolerant LWR Fuel in collaboration with industrial partners AREVA and EDF. Two potential solutions were investigated: chromium coated zirconium based claddings and SiC/SiC composite claddings with a metallic liner. Concerning the first solution, the optimization of chromium coatings on Zircaloy-4 substrate has been performed. Thus, it has been demonstrated that, due in particular to their slower oxidation rate, a significant additional 'grace period( can be obtained on high temperature oxidized coated claddings in comparison to the conventional uncoated ones, regarding their residual PQ (Post-Quench) ductility and their ability to survive to the final water quenching in LOCA and, to some extent, beyond LOCA conditions. Concerning the second solution, the innovative 'sandwich' SiC/SiC cladding concept is introduced. Initially designed for the next generation of nuclear reactors, it can be adapted to obtain high safety performance for LWRs in LOCA conditions. The key findings of this work highlight the low sensitivity of SiC/SiC composites under the explored steam oxidation conditions. No signification degradation of the mechanical properties of CVI-HNI SiC/SiC specimen is particularly acknowledged for relatively long duration (beyond 100 h at 1200 Celsius degrees). Despite these very positive preliminary results, significant studies and developments are still necessary to close the technology gap. Qualification for nuclear application requires substantial irradiation testing, additional characterization and the definition of design rules applicable to such a structure. The use of a SiC-based fuel cladding shows promise for the highest temperature accident conditions but remains a long term perspective

Experience in health care organization for victims of Chernobyl accident under conditions of spatial hospitals

International Nuclear Information System (INIS)

Nadezhina, N.M.

1990-01-01

Experience in organization of health care for victims of Chernobyl accidents under conditions of spatial hospitals are discussed taking into account patients with residual contamination of skin and clothe. A necessity of well-adjusted organization activites, including an inpatient clinic with well-equipped reception, dosimetric, haryological and bacteriological laboratories, an intensive care department, a surgical (burn) department, a blood transfusion laboratory and equipment for plasmopheresis and hemosorption is marked. Therapy of such patients should be developed along the following lines: 1) prevention and therapy of infectious complications; 2) blood cell substitution therapy; 3) bone marrow transplantation; 4) detoxicating therapy; 5) correction of water-electrolyte metabolism; 6) therapy of local radiation injuries

Containment integrity analysis under accidents

International Nuclear Information System (INIS)

Lin Chengge; Zhao Ruichang; Liu Zhitao

2010-01-01

Containment integrity analyses for current nuclear power plants (NPPs) mainly focus on the internal pressure caused by design basis accidents (DBAs). In addition to the analyses of containment pressure response caused by DBAs, the behavior of containment during severe accidents (SAs) are also evaluated for AP1000 NPP. Since the conservatism remains in the assumptions,boundary conditions and codes, margin of the results of containment integrity analyses may be overestimated. Along with the improvements of the knowledge to the phenomena and process of relevant accidents, the margin overrated can be appropriately reduced by using the best estimate codes combined with the uncertainty methods, which could be beneficial to the containment design and construction of large passive plants (LPP) in China. (authors)

Postulated accidents

International Nuclear Information System (INIS)

Ullrich, W.

1980-01-01

This lecture on 'Postulated Accidents' is the first of a series of lectures on the dynamic and transient behaviour of nuclear power plants, especially pressurized water reactors. The main points covered will be: Reactivity Accidents, Transients (Intact Loop) and Loss of Cooland Accidents (LOCA) including small leak. This lecture will discuss the accident analysis in general, the definition of the various operational phases, the accident classification, and, as an example, an accident sequence analysis on the basis of 'Postulated Accidents'. (orig./RW)

Development of Database for Accident Analysis in Indian Mines

Science.gov (United States)

Tripathy, Debi Prasad; Guru Raghavendra Reddy, K.

2016-10-01

Mining is a hazardous industry and high accident rates associated with underground mining is a cause of deep concern. Technological developments notwithstanding, rate of fatal accidents and reportable incidents have not shown corresponding levels of decline. This paper argues that adoption of appropriate safety standards by both mine management and the government may result in appreciable reduction in accident frequency. This can be achieved by using the technology in improving the working conditions, sensitising workers and managers about causes and prevention of accidents. Inputs required for a detailed analysis of an accident include information on location, time, type, cost of accident, victim, nature of injury, personal and environmental factors etc. Such information can be generated from data available in the standard coded accident report form. This paper presents a web based application for accident analysis in Indian mines during 2001-2013. An accident database (SafeStat) prototype based on Intranet of the TCP/IP agreement, as developed by the authors, is also discussed.

Control assembly ejection accident analysis for WWER-440 (Armenian NPP)

International Nuclear Information System (INIS)

Bznuni, S.; Malakyan, Ts.; Amirjanyan, A.; Ghasabyan, L.

2007-01-01

Control Assembly ejection in WWER-440 initiated by the loss of integrity of the Control Assemblies drive housing has been analyzed. This event causes a very rapid reactivity insertion to the core and small break LOCA which potentially could lead to rapid power increase and redistribution of heat release in the core resulting in a fuel, cladding and coolant temperature rise; primary pressure increase, radiological consequences due to loss of primary coolant and potential loss of cladding integrity and fuel disintegration (if applicable). Methodology of the analysis is based on conservative assumptions as well as on deterministic approach for selection of functioning logic of systems and equipment's to maximize reactor core power and minimize power decreasing reactivity feedback. Computational analyses were performed by 3D kinetics PARCS-RELAP coupled code. WWER-440 fuel cross-section libraries, diffusion coefficients and kinetics parameters were calculated by HELOS code. In this paper analysis of accident for Hot Full Power was presented. Results of analysis show that ANPP WWER-440 reactor design meets acceptance criteria prescribed for RIA type design based accidents (Authors)

The expert assistant in accident management

International Nuclear Information System (INIS)

Goddard, A.J.H.; Cannell, R.J.

1990-01-01

In the event of a nuclear accident in proximity to an urban area, the consequences resulting from the complex processes of environmental transport of radioactivity would require complex countermeasures. Emphasis has been placed on either modelling the potential effects of such an event on the population, or on attempting to predict the geographical evolution of the release. Less emphasis has been placed on the development of accident management aids with a in-built data acquisition capability. Given the problems of predicting the evolution of an accidental release of activity, more emphasis should be placed on the development of small regional systems specifically engineered to acquire and display environmental data in the most efficaceous form possible. A wealth of information can be obtained from appropriately-sited outstations which can aid those responsible for countermeasures in their decision making processes. The substantial volume of data which would arrive within the duration and during the aftermath of an accident requires skilled interpretation under conditions of considerable stress. It is necessary that a management aid notonly presents these data in a rapidly assimilable form, but is capable of making intelligent decisions of its own, on such matters as information display priority and the polling frequency of outstations. The requirement is for an expert assistant. The XERSES accident management aid has been designed with the foregoing features in mind. Intended for covering regions up to approximately 100 kms square, it links with between 1 and 64 outstations supplying a variety of environmental data. Under quiescent conditions the system will operate unattended, raising alarms remotely only when detecting abnormal conditions. Under emergency conditions, the system automatically adjusts such operating parameters as data acquisition rate

Improving aircraft accident forecasting for an integrated plutonium storage facility

International Nuclear Information System (INIS)

Rock, J.C.; Kiffe, J.; McNerney, M.T.; Turen, T.A.

1998-06-01

Aircraft accidents pose a quantifiable threat to facilities used to store and process surplus weapon-grade plutonium. The Department of Energy (DOE) recently published its first aircraft accident analysis guidelines: Accident Analysis for Aircraft Crash into Hazardous Facilities. This document establishes a hierarchy of procedures for estimating the small annual frequency for aircraft accidents that impact Pantex facilities and the even smaller frequency of hazardous material released to the environment. The standard establishes a screening threshold of 10 -6 impacts per year; if the initial estimate of impact frequency for a facility is below this level, no further analysis is required. The Pantex Site-Wide Environmental Impact Statement (SWEIS) calculates the aircraft impact frequency to be above this screening level. The DOE Standard encourages more detailed analyses in such cases. This report presents three refinements, namely, removing retired small military aircraft from the accident rate database, correcting the conversion factor from military accident rates (accidents per 100,000 hours) to the rates used in the DOE model (accidents per flight phase), and adjusting the conditional probability of impact for general aviation to more accurately reflect pilot training and local conditions. This report documents a halving of the predicted frequency of an aircraft impact at Pantex and points toward further reductions

Síndromes autoinflamatórias hereditárias na faixa etária pediátrica Pediatric hereditary autoinflammatory syndromes

Directory of Open Access Journals (Sweden)

Adriana Almeida Jesus

2010-10-01

Full Text Available OBJETIVO: Descrever as principais síndromes autoinflamatórias hereditárias na faixa etária pediátrica. FONTES DOS DADOS: Foi realizada uma revisão da literatura nas bases de dados PubMed e SciELO, utilizando as palavras-chave "síndromes autoinflamatórias” e "criança”, e incluindo referências bibliográficas relevantes. SÍNTESE DOS DADOS: As principais síndromes autoinflamatórias são causadas por defeitos monogênicos em proteínas da imunidade inata, sendo consideradas imunodeficiências primárias. Elas são caracterizadas clinicamente por sintomas inflamatórios sistêmicos recorrentes ou contínuos e devem ser diferenciadas das doenças infecciosas, autoimunes e outras imunodeficiências primárias. Nesta revisão, foram enfatizadas características epidemiológicas, manifestações clínicas, alterações laboratoriais, prognóstico e terapia das principais síndromes autoinflamatórias: febre familiar do Mediterrâneo; síndrome periódica associada ao receptor de fator de necrose tumoral; criopirinopatias; deficiência de mevalonato-quinase; artrite granulomatosa pediátrica; síndrome de pioderma gangrenoso, artrite piogênica e acne; síndrome de Majeed; e deficiência do antagonista do receptor de interleucina-1. As criopirinopatias discutidas foram: doença inflamatória multissistêmica de início neonatal ou síndrome neurológica, cutânea e articular crônica infantil, síndrome de Muckle-Wells e síndrome autoinflamatória familiar associada ao frio. CONCLUSÕES: É importante que o pediatra reconheça as síndromes autoinflamatórias hereditárias mais prevalentes, pois o encaminhamento ao reumatologista pediátrico pode permitir um diagnóstico precoce e uma instituição de tratamento adequado, possibilitando uma melhora da qualidade de vida dos pacientes.OBJECTIVE: To describe the most prevalent pediatric hereditary autoinflammatory syndromes. SOURCES: A review of the literature including relevant references

Sequence Tree Modeling for Combined Accident and Feed-and-Bleed Operation

International Nuclear Information System (INIS)

Kim, Bo Gyung; Kang Hyun Gook; Yoon, Ho Joon

2016-01-01

In order to address this issue, this study suggests the sequence tree model to analyze accident sequence systematically. Using the sequence tree model, all possible scenarios which need a specific safety action to prevent the core damage can be identified and success conditions of safety action under complicated situation such as combined accident will be also identified. Sequence tree is branch model to divide plant condition considering the plant dynamics. Since sequence tree model can reflect the plant dynamics, arising from interaction of different accident timing and plant condition and from the interaction between the operator action, mitigation system, and the indicators for operation, sequence tree model can be used to develop the dynamic event tree model easily. Target safety action for this study is a feed-and-bleed (F and B) operation. A F and B operation directly cools down the reactor cooling system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. In this study, a TLOFW accident and a TLOFW accident with LOCA were the target accidents. Based on the conventional PSA model and indicators, the sequence tree model for a TLOFW accident was developed. If sampling analysis is performed, practical accident sequences can be identified based on the sequence analysis. If a realistic distribution for the variables can be obtained for sampling analysis, much more realistic accident sequences can be described. Moreover, if the initiating event frequency under a combined accident can be quantified, the sequence tree model can translate into a dynamic event tree model based on the sampling analysis results

Sequence Tree Modeling for Combined Accident and Feed-and-Bleed Operation

Energy Technology Data Exchange (ETDEWEB)

Kim, Bo Gyung; Kang Hyun Gook [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [Khalifa University of Science, Abu Dhabi (United Arab Emirates)

2016-05-15

In order to address this issue, this study suggests the sequence tree model to analyze accident sequence systematically. Using the sequence tree model, all possible scenarios which need a specific safety action to prevent the core damage can be identified and success conditions of safety action under complicated situation such as combined accident will be also identified. Sequence tree is branch model to divide plant condition considering the plant dynamics. Since sequence tree model can reflect the plant dynamics, arising from interaction of different accident timing and plant condition and from the interaction between the operator action, mitigation system, and the indicators for operation, sequence tree model can be used to develop the dynamic event tree model easily. Target safety action for this study is a feed-and-bleed (F and B) operation. A F and B operation directly cools down the reactor cooling system (RCS) using the primary cooling system when residual heat removal by the secondary cooling system is not available. In this study, a TLOFW accident and a TLOFW accident with LOCA were the target accidents. Based on the conventional PSA model and indicators, the sequence tree model for a TLOFW accident was developed. If sampling analysis is performed, practical accident sequences can be identified based on the sequence analysis. If a realistic distribution for the variables can be obtained for sampling analysis, much more realistic accident sequences can be described. Moreover, if the initiating event frequency under a combined accident can be quantified, the sequence tree model can translate into a dynamic event tree model based on the sampling analysis results.

Pilot Domain Task Experience in Night Fatal Helicopter Emergency Medical Service Accidents.

Science.gov (United States)

Aherne, Bryan B; Zhang, Chrystal; Newman, David G

2016-06-01

In the United States, accident and fatality rates in helicopter emergency medical service (HEMS) operations increase significantly under nighttime environmentally hazardous operational conditions. Other studies have found pilots' total flight hours unrelated to HEMS accident outcomes. Many factors affect pilots' decision making, including their experience. This study seeks to investigate whether pilot domain task experience (DTE) in HEMS plays a role against likelihood of accidents at night when hazardous operational conditions are entered. There were 32 flights with single pilot nighttime fatal HEMS accidents between 1995 and 2013 with findings of controlled flight into terrain (CFIT) and loss of control (LCTRL) due to spatial disorientation (SD) identified. The HEMS DTE of the pilots were compared with industry survey data. Of the pilots, 56% had ≤2 yr of HEMS experience and 9% had >10 yr of HEMS experience. There were 21 (66%) accidents that occurred in non-visual flight rules (VFR) conditions despite all flights being required to be conducted under VFR. There was a statistically significant increase in accident rates in pilots with pilots with >10 yr HEMS DTE. HEMS DTE plays a preventive role against the likelihood of a night operational accident. Pilots with limited HEMS DTE are more likely to make a poor assessment of hazardous conditions at night, and this will place HEMS flight crew at high risk in the VFR night domain.

System 80+ design features for severe accident prevention and mitigation

International Nuclear Information System (INIS)

Jacob, M.C.; Schneider, R.E.; Finnicum, D.J.

1993-01-01

ABB-CE, in cooperation with the US Department of Energy, is working to develop and certify the System 80+ design, which is ABB-CE's standardized evolutionary Advanced Light Water Reactor (ALWR) design. It incorporates design enhancements based on Probabilistic Risk Assessment (PRA) insights, guidance from the EPRI's Utility Requirements Document, and US NRC's Severe Accident Policy. Major severe accident prevention and mitigation design features of the system is discussed along with its conformance to EPRI URD guidance, as applicable. Computer simulation of a best estimate severe accident scenario is presented to illustrate the acceptable containment performance of the design. It is concluded that by considering severe accident prevention and mitigation early in the design process, the System 80+ design represents a robust plant design that has low core damage frequencies, low containment conditional failure probabilities, and acceptable deterministic containment performance under severe accident conditions

The effect of system modeling on the Fukushima accident evolution

Energy Technology Data Exchange (ETDEWEB)

Herranz, L.E.; Fontanet, J.; López, C.; Fernández, E.

2015-07-01

The Fukushima accident is becoming both a unique opportunity and a huge challenge for severe accident analysis. The OECD-BSAF project has articulated a good part of the modeling efforts conducted so far. Inside this project, CIEMAT has conducted forensic analyses of the Fukushima accident in units 1 through 3 with MELCOR 2.1 and it has postulated a set of accident scenarios consistent with data. Beyond specific results, sensitivity analyses on safety systems performance and prevailing boundary conditions have highlighted the need of conducting uncertainty analyses when modeling NPPs severe accident scenarios. (Author)

RIA: Principles and application

International Nuclear Information System (INIS)

Pappas, A.A.; Glassman, A.B.

1983-01-01

What is the future of RIA? Has the application of RIA peaked? Will other and competing tests such as immunofluorescence and ELISA systems displace or replace the method? RIA is a sensitive, precise, and very often specific analytical tool. Its primary advantage is exquisite sensitivity. Problems related to specificity of antibody and/or antigen identification are reviewed in this paper. The same limitations will be encountered in the similar techniques of enzyme immunologic determination. Increasing difficulties with waste disposal of either radioactive material and/or organic solvents will cause those who utilize radionuclides to look again at alternatives. RIA has been an exciting developmental tool that has led the authors to look at dynamic physiologic and biochemical interactions. The time may come when there is replacement of the radionuclide portion by enzymes or fluorescent material

Release of fission products during controlled loss-of-coolant accidents and hypothetical core meltdown accidents

International Nuclear Information System (INIS)

Albrecht, H.; Malinauskas, A.P.

1978-01-01

A few years ago the Projekt Nukleare Sicherheit joined the United States Nuclear Regulatory Commission in the development of a research program which was designed to investigate fission product release from light water reactor fuel under conditions ranging from spent fuel shipping cask accidents to core meltdown accidents. Three laboratories have been involved in this cooperative effort. At Argonne National Laboratory (ANL), the research effort has focused on noble gas fission product release, whereas at Oak Ridge National Laboratory (ORNL) and at Kernforschungszentrum Karlsruhe (KfK), the studies have emphasized the release of species other than the noble gases. In addition, the ORNL program has been directed toward the development of fission product source terms applicable to analyses of spent fuel shipping cask accidents and controlled loss-of-coolant accidents, and the KfK program has been aimed at providing similar source terms which are characteristic of core meltdown accidents. The ORNL results are presented for fission product release from defected fuel rods into a steam atmosphere over the temperature range 500 to 1200 0 C, and the KfK results for release during core meltdown sequences

Accident management

International Nuclear Information System (INIS)

Lutz, R.J.; Monty, B.S.; Liparulo, N.J.; Desaedeleer, G.

1989-01-01

The foundation of the framework for a Severe Accident Management Program is the contained in the Probabilistic Safety Study (PSS) or the Individual Plant Evaluations (IPE) for a specific plant. The development of a Severe Accident Management Program at a plant is based on the use of the information, in conjunction with other applicable information. A Severe Accident Management Program must address both accident prevention and accident mitigation. The overall Severe Accident Management framework must address these two facets, as a living program in terms of gathering the evaluating information, the readiness to respond to an event. Significant international experience in the development of severe accident management programs exist which should provide some direction for the development of Severe Accident Management in the U.S. This paper reports that the two most important elements of a Severe Accident Management Program are the Emergency Consultation process and the standards for measuring the effectiveness of individual Severe Accident Management Programs at utilities

The nuclear accidents: Causes and consequences

International Nuclear Information System (INIS)

Rochd, M.

1988-01-01

The author discussed and compared the real causes of T.M.I. and Chernobyl accidents and cited their consequences. To better understand how these accidents occurred, a brief description of PWR type (reactor type of T.M.I.) and of RBMK type (reactor type of Chernobyl) has been presented. The author has also set out briefly the safety analysis objectives and the three barriers established to protect the public against the radiological consequences. To distinguish failures that cause severe accidents and to analyze them in details, it is necessary to classify the accidents. There are many ways to do it according to their initiator event, or to their frequency, or to their degree of gravity. The safety criteria adopted by nuclear industry have been explained. These criteria specify the limits of certain physical parameters that should not be exceeded in case of incidents or accidents. To compare the real causes of T.M.I. and Chernobyl accidents, the events that led to both have been presented. As observed the main common contributing factors in both cases are that the operators did not pay attention to warnings and signals that were available to them and that they were not trained to handle these accident sequences. The essential conclusions derived from these severe accidents are: -The improvement of operators competence contribute to reduce the accident risks; -The rapid and correct diagnosis of real conditions at each point of the accidents permits an appropriate behavior that would bring the plant to a stable state; -Competent technical teams have to intervene and to assist the operators in case of emergency; -Emergency plans and an international collaboration are necessary to limit the accident risks. 11 figs. (author)

[Drugs and occupational accident].

Science.gov (United States)

Bratzke, H; Albers, C

1996-02-01

In a case of a fatal occupational accident (construction worker, fall from roof, urine test positive for cocaine and THC, e.g. cannabis) the question arised to what extent those drug-related occupational accidents occur. In the literature only few cases, mainly dealing with cannabis influence, have been reported, however, a higher number is suspected. Cocaine and other stimulating drugs (amphetamine) are more often used to increase physical fitness. By direct or indirect interference with vigilance these compounds may provoke accidents. Due to the lack of a legal basis proving of the influence of drugs at the working place is still very limited, although highly sensitive chemical-toxicological assay procedures are available to detect even the chronic abuse (in hair). In the general conditions of accident insurances a compensation is excluded when alcohol is involved, but drugs are not mentioned. It is indeed difficult to establish a concentration limit for drugs like that existing for alcohol (1.1%). In each case the assay of the drug involved and exact knowledge of its specific effects is in an essential prerequisite to prove the causal relationship.

Disfunção gustatória e olfatória em laringectomizados

Directory of Open Access Journals (Sweden)

Ada Salvetti Cavalcanti Caldas

2013-10-01

Full Text Available Após a cirurgia de laringectomia total, o fluxo aéreo nasal é transferido definitivamente para o traqueostoma, comprometendo a chegada de moléculas odoríferas até a cavidade nasal, podendo repercutir em alterações na percepção olfatória e gustatória nesses indivíduos. OBJETIVO: Avaliar as funções do olfato e do paladar em laringectomizados totais. Desenho do estudo: Estudo de série. MÉTODO: A amostra envolveu um grupo com 25 pacientes submetidos à laringectomia total e outro grupo de comparação com 25 pacientes não laringectomizados. A função gustatória foi avaliada por tiras gustativas de papel de filtro. Para avaliação da função olfatória, foi aplicado o teste Brief Smell Identification Test. RESULTADOS: No grupo de laringectomizados, houve maior frequência de hipogeusia (80%; p < 0,05, assim como de hiposmia (88%; p < 0,001, isoladas e concomitantes (72%; p < 0,001. Na discriminação dos sabores, o sabor amargo não diferiu entre os grupos, diferentemente dos demais sabores. No aspecto olfatório, os laringectomizados tiveram pior desempenho na detecção de odores de alerta e os relacionados à alimentação. Identificou-se que história de tabagismo e de alcoolismo foi significantemente mais frequente dentre laringectomizados. CONCLUSÃO: A diminuição das funções olfatória e gustatória em laringectomizados totais foi evidenciada nesse estudo.

Ideal storage conditions study of the second antibody for radioimmunoassay (RIA) totality produced in the country (sheep serum anti-IgG of rabbit)

International Nuclear Information System (INIS)

Silva, S.R.; Borghi, V.C.; Mesquita, C.M.; Wajchenberg, B.L.

1994-01-01

This work has been carried out to establishing the ideal storage conditions of the second RIA antibody produced at IPEN-CNEN/SP. Small samples of these antisera were submitted to two kinds of freezing forms (slow and fast), both followed by lyophilization. The interference of the frozen and lyophilization processes were compared through the antibody dilution curve. The obtained values showed that no significant difference between the freezing forms occurred. (author). 9 refs, 2 figs, 3 tabs

Fan Cooler Operation in Kori 1 for Mitigating Severe Accident

International Nuclear Information System (INIS)

Suh, Nam Duk; Park, Jae Hong

2005-01-01

The Korea Ministry of Science and Technology (MOST) issued the 'Policy on Severe Accident of Nuclear Power Plants' in August 2001. According to the policy it was required for the licensee to develop a plant specific severe accident management guideline (SAMG) and to implement it. Thus the utility has made an implementation plan to develop SAMGs for operating plants. The SAMG for Kori unit 1 was submitted to the government on January 2004. Since then, the government trusted KINS to review the submitted SAMG in view of its feasibility and effectiveness. The first principle of the developed SAMG is to use only the available facilities as it is without introducing any system change. Because Kori-1 has no mitigative facility against combustible gases during severe accident, it relies heavily both on spray and on fan cooler systems to control the containment condition. Thus one of the issues raised during the review is to know whether the fan coolers which are designed for DBA LOCA can be effective in mitigating the severe accident conditions. This paper presents an analysis result of fan cooler operation in controlling the containment condition during severe accident of Kori 1

Fuel temperature analysis method for channel-blockage accident in HTTR

International Nuclear Information System (INIS)

Maruyama, So; Fujimoto, Nozomu; Sudo, Yukio; Kiso, Yoshihiro; Hayakawa, Hitoshi

1994-01-01

During operation of the High Temperature Engineering Test Reactor (HTTR), coolability must be maintained without core damage under all postulated accident conditions. Channel blockage of a fuel element was selected as one of the design-basis accidents in the safety evaluation of the reactor. The maximum fuel temperature for such a scenario has been evaluated in the safety analysis and is compared to the core damage limits.For the design of the HTTR, an in-core thermal and hydraulic analysis code ppercase[flownet/trump] was developed. This code calculates fuel temperature distribution, not only for a channel blockage accident but also for transient conditions. The validation of ppercase[flownet/trump] code was made by comparison of the analytical results with the results of thermal and hydraulic tests by the Helium Engineering Demonstration Loop (HENDEL) multi-channel test rig (T 1-M ), which simulated one fuel column in the core. The analytical results agreed well with the experiments in which the HTTR operating conditions were simulated.The maximum fuel temperature during a channel blockage accident is 1653 C. Therefore, it is confirmed that the integrity of the core is maintained during a channel blockage accident. ((orig.))

Hot Cell Installation and Demonstration of the Severe Accident Test Station

Energy Technology Data Exchange (ETDEWEB)

Linton, Kory D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Burns, Zachary M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Terrani, Kurt A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Yan, Yong [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-08-01

A Severe Accident Test Station (SATS) capable of examining the oxidation kinetics and accident response of irradiated fuel and cladding materials for design basis accident (DBA) and beyond design basis accident (BDBA) scenarios has been successfully installed and demonstrated in the Irradiated Fuels Examination Laboratory (IFEL), a hot cell facility at Oak Ridge National Laboratory. The two test station modules provide various temperature profiles, steam, and the thermal shock conditions necessary for integral loss of coolant accident (LOCA) testing, defueled oxidation quench testing and high temperature BDBA testing. The installation of the SATS system restores the domestic capability to examine postulated and extended LOCA conditions on spent fuel and cladding and provides a platform for evaluation of advanced fuel and accident tolerant fuel (ATF) cladding concepts. This document reports on the successful in-cell demonstration testing of unirradiated Zircaloy-4. It also contains descriptions of the integral test facility capabilities, installation activities, and out-of-cell benchmark testing to calibrate and optimize the system.

Whole-Pin Furnace system: An experimental facility for studying irradiated fuel pin behavior under potential reactor accident conditions

International Nuclear Information System (INIS)

Liu, Y.Y.; Tsai, H.C.; Donahue, D.A.; Pushis, D.O.; Savoie, F.E.; Holland, J.W.; Wright, A.E.; August, C.; Bailey, J.L.; Patterson, D.R.

1990-05-01

The whole-pin furnace system is a new in-cell experimental facility constructed to investigate how irradiated fuel pins may fail under potential reactor accident conditions. Extensive checkouts have demonstrated excellent performance in remote operation, temperature control, pin breach detection, and fission gas handling. The system is currently being used in testing of EBIR-II-irradiated Integral Fast Reactor (IFR) metal fuel pins; future testing will include EBR-II-irradiated mixed-oxide fuel pins. 7 refs., 4 figs

Analyzing the severity of accidents on the German Autobahn.

Science.gov (United States)

Manner, Hans; Wünsch-Ziegler, Laura

2013-08-01

We study the severity of accidents on the German Autobahn in the state of North Rhine-Westphalia using data for the years 2009 until 2011. We use a multinomial logit model to identify statistically relevant factors explaining the severity of the most severe injury, which is classified into the four classes fatal, severe injury, light injury and property damage. Furthermore, to account for unobserved heterogeneity we use a random parameter model. We study the effect of a number of factors including traffic information, road conditions, type of accidents, speed limits, presence of intelligent traffic control systems, age and gender of the driver and location of the accident. Our findings are in line with studies in different settings and indicate that accidents during daylight and at interchanges or construction sites are less severe in general. Accidents caused by the collision with roadside objects, involving pedestrians and motorcycles, or caused by bad sight conditions tend to be more severe. We discuss the measures of the 2011 German traffic safety programm in the light of our results. Copyright © 2013 Elsevier Ltd. All rights reserved.

Iodine/steel reactions under severe accident conditions in LWR's

International Nuclear Information System (INIS)

Funke, F.; Greger, G-U.; Hellman, S.; Bleier, A.; Morell, W.

1994-01-01

Due to large surface areas, the reaction of volatile, molecular iodine (I 2 ) with steel surfaces in the containment may play an important role in predicting the source term to the environment. Both wall retention of iodine and conversion of volatile into non-volatile iodine compounds at steel surfaces have to be considered. Two types of laboratory experiments were carried out at Siemens/KWU in order to investigate the reaction of I 2 at steel surfaces representative for German power plants. 1) For steel coupons submerged in an I 2 solution at T = 50 deg C, 90 deg C or 140 deg C the reaction rate of the I 2 /I - conversion was determined. No iodine loading was observed on the steel in the aqueous phase tests. I 2 reacts with the steel components (Fe, Cr or Ni) to form metal iodides on the surface which are all immediately dissolved in water under dissociation into the metal and the iodide ions. From these experiments, the I 2 /I - conversion rate constants over the temperature range 50 deg C - 140 deg C as well as the activation energy were determined. The measured data are suitable to be included in severe accident iodine codes such as IMPAIR. 2) Steel tubes were exposed to a steam/I 2 flow under dry air at T=120 deg C and steam-condensing conditions at T= 120 deg C and 160 deg C. In dry air I 2 was retained on the steel surface and a deposition rate constant was measured. Under steam-condensing conditions there is an effective conversion of volatile I 2 to non-volatile I - which is subsequently washed off from the steel surface. The I 2 /I - conversion rate constants suitable for modelling this process were determined. No temperature dependency was found in the range 120 deg C - 160 deg C. (author). 4 refs., 2 tabs., 7 figs

Safety assurance logic techniques for evaluation of accident prevention and mitigation

International Nuclear Information System (INIS)

McWethy, L.M.; Hagan, J.W.

1976-01-01

Safety assurance methods have been developed and applied in reactor safety assessments of FFTF. These methods promote visibility of the total safety provided by the plant, both in prevention of off-normal or accident conditions as well as provision of various features which terminate conditions within acceptable bounds if such conditions should occur. One of the primary techniques applied in safety assurance is the development of safety assurance diagrams. These diagrams explicitly identify the multiple lines of defense which prevent accident progression. The diagrams graphically demonstrate the defense-in-depth provided by the plant for each postulated occurrence. Lines of defense are shown against ever having an occurrence in the first place; thus giving appropriate emphasis on accident prevention, and visibility to the designer's role in promoting this level of safety. These diagrams, or accident process trees, also show graphically the various paths of postulated accident progression to their logical termination. Evaluation of the importance and strength of each line-of-defense assures fulfillment of the safety objectives of the overall plant system

[Guilty victims: a model to perpetuate impunity for work-related accidents].

Science.gov (United States)

Vilela, Rodolfo Andrade Gouveia; Iguti, Aparecida Mari; Almeida, Ildeberto Muniz

2004-01-01

This article analyzes reports and data from the investigation of severe and fatal work-related accidents by the Regional Institute of Criminology in Piracicaba, São Paulo State, Brazil. Some 71 accident investigation reports were analyzed from 1998, 1999, and 2000. Accidents involving machinery represented 38.0% of the total, followed by high falls (15.5%), and electric shocks (11.3%). The reports conclude that 80.0% of the accidents are caused by "unsafe acts" committed by workers themselves, while the lack of safety or "unsafe conditions" account for only 15.5% of cases. Victims are blamed even in situations involving high risk in which not even minimum safety conditions are adopted, thus favoring employers' interests. Such conclusions reflect traditional reductionist explanatory models, in which accidents are viewed as simple, unicausal phenomena, generally focused on slipups and errors by the workers themselves. Despite criticism in recent decades from the technical and academic community, this concept is still hegemonic, thus jeopardizing the development of preventive policies and the improvement of work conditions.

Water reactor fuel behaviour and fission products release in off-normal and accident conditions

International Nuclear Information System (INIS)

1987-09-01

The present meeting was scheduled by the International Atomic Energy Agency upon the proposal of the Members of the International Working Group on Water Reactor Fuel Performance and Technology and held at the IAEA Headquarters in Vienna from 10 to 13 November 1986. Thirty participants from 17 countries and an international organization attended the meeting. Eighteen papers were presented from 13 countries and one international organization. The meeting was composed of four sessions and covered subjects related to: physico-chemical properties of core materials under off-normal conditions, and their interactions up to and after melt-down (5 papers); core materials deformation, relocation and core coolability under (severe) accident conditions (4 papers); fission products release: including experience, mechanisms and modelling (5 papers); power plant experience (4 papers). A separate abstract was prepared for each of these 18 papers. Four working groups covering the above-mentioned topics were held to discuss the present status of the knowledge and to develop recommendations for future activities in this field. Refs, figs and tabs

Telerehabilitació en pacients amb accidents cerebrovascular: revisió bibliogràfica.

OpenAIRE

Riba Lafarga, Roger

2014-01-01

L’ ictus és una alteració brusca de la circulació de la sang al cervell, sent la segona causa de mort al món i la primera en discapacitat. Objectius. Examinar si la telerehabilitació i la realitat virtual poden millorar l'estat físic i psíquic dels pacients amb accident cerebrovascular i avaluar l’impacte en les activitats de la vida diària. Conclusió. Els resultats indiquen que la fisioteràpia convencional i un programa combinat de telerehabilitació o realitat virtual amb fisioteràpia, mi...

Inherent Safety Feature of Hybrid Low Power Research Reactor during Reactivity Induced Accident

Energy Technology Data Exchange (ETDEWEB)

Kim, DongHyun; Yum, Soo Been; Hong, Sung Teak; Lim, In-Cheol [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

Hybrid low power research reactor(H-LPRR) is the new design concept of low power research reactor for critical facility as well as education and training. In the case of typical low power research reactor, the purposes of utilization are the experiments for education of nuclear engineering students, Neutron Activation Analysis(NAA) and radio-isotope production for research purpose. H-LPRR is a light-water cooled and moderated research reactor that uses rod-type LEU UO{sub 2} fuels same as those for commercial power plants. The maximum core thermal power is 70kW and, the core is placed in the bottom of open pool. There are 1 control rod and 2 shutdown rods in the core. It is designed to cool the core by natural convection, retain negative feedback coefficient for entire fuel periods and operate for 20 years without refueling. Inherent safety in H-LPRR is achieved by passive design features such as negative temperature feedback coefficient and core cooling by natural convection during normal and emergency conditions. The purpose of this study is to find out that the inherent safety characteristics of H-LPRR is able to control the power and protect the reactor from the RIA(Reactivity induced accident). RIA analysis was performed to investigate the inherent safety feature of H-LPRR. As a result, it was found that the reactor controls its power without fuel damage in the event and that the reactor remains safe states inherently. Therefore, it is believed that high degree of safety inheres in H-LPRR.

Assessment of two BWR accident management strategies

International Nuclear Information System (INIS)

Hodge, S.A.; Petek, M.

1991-01-01

A recently completed Oak Ridge effort proposes two management strategies for mitigation of the events that might occur in-vessel after the onset of significant core damage in a BWR severe accident. While the probability of such an accident is low, there may be effective yet inexpensive mitigation measures that could be implemented employing the existing plant equipment and requiring only additions to the plant emergency procedures. In this spirit, accident management strategies have been proposed for use of a borated solution for reactor vessel refill should control blade damage occur during a period of temporary core dryout and for containment flooding to maintain the core debris within the reactor vessel if injection systems cannot be restored. The proposed strategy for poisoning of the water used for vessel reflood should injection systems be restored after control blade damage has occurred has great promise, using only the existing plant equipment but employing a different chemical form for the boron poison. The dominant BWR severe accident sequence is Station Blackout and without means for mechanical stirring or heating of the storage tank, the question of being able to form the poisoned solution under accident conditions becomes of supreme importance. On the other hand, the proposed strategy for drywell flooding to cool the reactor vessel bottom head and prevent the core and structure debris from escaping to the drywell holds less promise. This strategy does, however, have potential for future plant designs in which passive methods might be employed to completely submerge the reactor vessel under severe accident conditions without the need for containment venting

Visual investigation of transient fuel behavior under a rapid heating condition

International Nuclear Information System (INIS)

Saito, Shinzo

1981-10-01

An in-reactor experimental research on fuel behavior under reactivity initiated accident (RIA) conditions is being conducted in the Nuclear Safety Research Reactor (NSRR). The optical system in which a non-browning lens periscope is directly installed in the test section was successfully developed for photographing transient fuel behavior. Several phenomena which had never been revealed before were observed in the slow motion pictures taken in the NSRR experiments which were performed in the water and air environments. As for incipient failure mechanism for an unirradiated fuel rod under RIA conditions, brittle fracture of the cladding during quenching is dominant. However, a split cracking possibly occurs during even red hot state of the cladding. It is considered that the crack is generated by the local internal pressure increase at the specified region blocked up due to the melting of the cladding inner surface. The film boiling is unexpectablly violent specially in the early stage of the transient, and film thickness becomes 5 -- 6 mm at maximum. The observed thick vapor film can not be explained by the conventional theory, but the effect of hydrogen which is produced by Zircaloy-water reaction is reasonably explained to form thick film in the report. The molten fuel was expelled from the cladding in the experiment which was performed in an air environment. The expelled fuel fragmented due to possibly initial motion effect, not mechanical collision effect, because Weber number is smaller than the critical value. (author)

Development of Parameter Network for Accident Management Applications

Energy Technology Data Exchange (ETDEWEB)

Pak, Sukyoung; Ahemd, Rizwan; Heo, Gyunyoung [Kyung Hee Univ., Yongin (Korea, Republic of); Kim, Jung Taek; Park, Soo Yong; Ahn, Kwang Il [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

When a severe accident happens, it is hard to obtain the necessary information to understand of internal status because of the failure or damage of instrumentation and control systems. We learned the lessons from Fukushima accident that internal instrumentation system should be secured and must have ability to react in serious conditions. While there might be a number of methods to reinforce the integrity of instrumentation systems, we focused on the use of redundant behavior of plant parameters without additional hardware installation. Specifically, the objective of this study is to estimate the replaced value which is able to identify internal status by using set of available signals when it is impossible to use instrumentation information in a severe accident, which is the continuation of the paper which was submitted at the last KNS meeting. The concept of the VPN was suggested to improve the quality of parameters particularly to be logged during severe accidents in NPPs using a software based approach, and quantize the importance of each parameter for further maintenance. In the future, we will continue to perform the same analysis to other accident scenarios and extend the spectrum of initial conditions so that we are able to get more sets of VPNs and ANN models to predict the behavior of accident scenarios. The suggested method has the uncertainty underlain in the analysis code for severe accidents. However, In case of failure to the safety critical instrumentation, the information from the VPN would be available to carry out safety management operation.

Benchmarking Severe Accident Computer Codes for Heavy Water Reactor Applications

International Nuclear Information System (INIS)

2013-12-01

Requests for severe accident investigations and assurance of mitigation measures have increased for operating nuclear power plants and the design of advanced nuclear power plants. Severe accident analysis investigations necessitate the analysis of the very complex physical phenomena that occur sequentially during various stages of accident progression. Computer codes are essential tools for understanding how the reactor and its containment might respond under severe accident conditions. The IAEA organizes coordinated research projects (CRPs) to facilitate technology development through international collaboration among Member States. The CRP on Benchmarking Severe Accident Computer Codes for HWR Applications was planned on the advice and with the support of the IAEA Nuclear Energy Department's Technical Working Group on Advanced Technologies for HWRs (the TWG-HWR). This publication summarizes the results from the CRP participants. The CRP promoted international collaboration among Member States to improve the phenomenological understanding of severe core damage accidents and the capability to analyse them. The CRP scope included the identification and selection of a severe accident sequence, selection of appropriate geometrical and boundary conditions, conduct of benchmark analyses, comparison of the results of all code outputs, evaluation of the capabilities of computer codes to predict important severe accident phenomena, and the proposal of necessary code improvements and/or new experiments to reduce uncertainties. Seven institutes from five countries with HWRs participated in this CRP

Analysis of Maximum Reasonably Foreseeable Accidents for the Yucca Mountain Draft Environmental Impact Statement (DEIS)

International Nuclear Information System (INIS)

Ross, S.B.; Best, R.E.; Maheras, S.J.; McSweeney, T.I.

2001-01-01

Accidents could occur during the transportation of spent nuclear fuel and high-level radioactive waste. This paper describes the risks and consequences to the public from accidents that are highly unlikely but that could have severe consequences. The impact of these accidents would include those to a collective population and to hypothetical maximally exposed individuals (MEIs). This document discusses accidents with conditions that have a chance of occurring more often than 1 in 10 million times in a year, called ''maximum reasonably foreseeable accidents''. Accidents and conditions less likely than this are not considered to be reasonably foreseeable

Development of Assessment Methodology of Chemical Behavior of Volatile Iodide under Severe Accident Conditions Using EPICUR Experiments

International Nuclear Information System (INIS)

Oh, Jae Yong; Yun, Jong Il; Kim, Do Sam; Han Chul

2011-01-01

Iodine is one of the most important fission products produced in nuclear power plants. Under severe accident condition, iodine exists as a variety of species in the containment such as aqueous iodide, gaseous iodide, iodide aerosol, etc. Following release of iodine from the reactor, mostly in the form of CsI aerosol, volatile iodine can be generated from the containment sump and release to the environment. Especially, volatile organic iodide can be produced from interaction between nonvolatile iodine and organic substances present in the containment. Volatile iodide could significantly influence the alienated residents surrounding the nuclear power plant. In particular, thyroid is vulnerable to radioiodine due to its high accumulation. Therefore, it is necessary for the Korea Institute of Nuclear Safety (KINS) to develop an evaluation model which can simulate iodine behavior in the containment following a severe accident. KINS also needs to make up its methodology for radiological consequence analysis, based on MELCOR-MACCS2 calculation, by coupling a simple iodine model which can conveniently deal with organic iodides. In the long term, such a model can contribute to develop an accident source term, which is one of urgent domestic needs. Our strategy for developing the model is as follows: 1. Review the existing methodologies, 2. Develop a simple stand-alone model, 3. Validate the model using ISTP-EPICUR (Experimental Program on Iodine Chemistry under Radiation) and OECD-BIP (Behavior of Iodine Project) experimental data. In this paper we present the context of development and validation of our model named RAIM (Radio-active iodine chemistry model)

Development of Assessment Methodology of Chemical Behavior of Volatile Iodide under Severe Accident Conditions Using EPICUR Experiments

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Yong; Yun, Jong Il [KAIST, Daejeon (Korea, Republic of); Kim, Do Sam; Han Chul [Korea Institue of Nuclear Safety, Daejeon (Korea, Republic of)

2011-05-15

Iodine is one of the most important fission products produced in nuclear power plants. Under severe accident condition, iodine exists as a variety of species in the containment such as aqueous iodide, gaseous iodide, iodide aerosol, etc. Following release of iodine from the reactor, mostly in the form of CsI aerosol, volatile iodine can be generated from the containment sump and release to the environment. Especially, volatile organic iodide can be produced from interaction between nonvolatile iodine and organic substances present in the containment. Volatile iodide could significantly influence the alienated residents surrounding the nuclear power plant. In particular, thyroid is vulnerable to radioiodine due to its high accumulation. Therefore, it is necessary for the Korea Institute of Nuclear Safety (KINS) to develop an evaluation model which can simulate iodine behavior in the containment following a severe accident. KINS also needs to make up its methodology for radiological consequence analysis, based on MELCOR-MACCS2 calculation, by coupling a simple iodine model which can conveniently deal with organic iodides. In the long term, such a model can contribute to develop an accident source term, which is one of urgent domestic needs. Our strategy for developing the model is as follows: 1. Review the existing methodologies, 2. Develop a simple stand-alone model, 3. Validate the model using ISTP-EPICUR (Experimental Program on Iodine Chemistry under Radiation) and OECD-BIP (Behavior of Iodine Project) experimental data. In this paper we present the context of development and validation of our model named RAIM (Radio-active iodine chemistry model)

Global ship accidents and ocean swell-related sea states

Directory of Open Access Journals (Sweden)

Z. Zhang

2017-11-01

Full Text Available With the increased frequency of shipping activities, navigation safety has become a major concern, especially when economic losses, human casualties and environmental issues are considered. As a contributing factor, the sea state plays a significant role in shipping safety. However, the types of dangerous sea states that trigger serious shipping accidents are not well understood. To address this issue, we analyzed the sea state characteristics during ship accidents that occurred in poor weather or heavy seas based on a 10-year ship accident dataset. Sea state parameters of a numerical wave model, i.e., significant wave height, mean wave period and mean wave direction, were analyzed for the selected ship accident cases. The results indicated that complex sea states with the co-occurrence of wind sea and swell conditions represent threats to sailing vessels, especially when these conditions include similar wave periods and oblique wave directions.

Global ship accidents and ocean swell-related sea states

Science.gov (United States)

Zhang, Zhiwei; Li, Xiao-Ming

2017-11-01

With the increased frequency of shipping activities, navigation safety has become a major concern, especially when economic losses, human casualties and environmental issues are considered. As a contributing factor, the sea state plays a significant role in shipping safety. However, the types of dangerous sea states that trigger serious shipping accidents are not well understood. To address this issue, we analyzed the sea state characteristics during ship accidents that occurred in poor weather or heavy seas based on a 10-year ship accident dataset. Sea state parameters of a numerical wave model, i.e., significant wave height, mean wave period and mean wave direction, were analyzed for the selected ship accident cases. The results indicated that complex sea states with the co-occurrence of wind sea and swell conditions represent threats to sailing vessels, especially when these conditions include similar wave periods and oblique wave directions.

Analysis of ex-vessel melt jet breakup and coolability. Part 1: Sensitivity on model parameters and accident conditions

Energy Technology Data Exchange (ETDEWEB)

Moriyama, Kiyofumi; Park, Hyun Sun, E-mail: hejsunny@postech.ac.kr; Hwang, Byoungcheol; Jung, Woo Hyun

2016-06-15

Highlights: • Application of JASMINE code to melt jet breakup and coolability in APR1400 condition. • Coolability indexes for quasi steady state breakup and cooling process. • Typical case in complete breakup/solidification, film boiling quench not reached. • Significant impact of water depth and melt jet size; weak impact of model parameters. - Abstract: The breakup of a melt jet falling in a water pool and the coolability of the melt particles produced by such jet breakup are important phenomena in terms of the mitigation of severe accident consequences in light water reactors, because the molten and relocated core material is the primary heat source that governs the accident progression. We applied a modified version of the fuel–coolant interaction simulation code, JASMINE, developed at Japan Atomic Energy Agency (JAEA) to a plant scale simulation of melt jet breakup and cooling assuming an ex-vessel condition in the APR1400, a Korean advanced pressurized water reactor. Also, we examined the sensitivity on seven model parameters and five initial/boundary condition variables. The results showed that the melt cooling performance of a 6 m deep water pool in the reactor cavity is enough for removing the initial melt enthalpy for solidification, for a melt jet of 0.2 m initial diameter. The impacts of the model parameters were relatively weak and that of some of the initial/boundary condition variables, namely the water depth and melt jet diameter, were very strong. The present model indicated that a significant fraction of the melt jet is not broken up and forms a continuous melt pool on the containment floor in cases with a large melt jet diameter, 0.5 m, or a shallow water pool depth, ≤3 m.

A radioactive waste transportation package monitoring system for normal transport and accident emergency response conditions

International Nuclear Information System (INIS)

Brown, G.S.; Cashwell, J.W.; Apple, M.L.

1991-01-01

Shipments of radioactive material (RAM) constitute but a small fraction of the total hazardous materials shipped in the United States each year. Public perception, however, of the potential consequences of a release from a transportation package containing RAM has resulted in significant regulation of transport operations, both to ensure the integrity of a package in accident conditions and to place operational constraints on the shipper. Much of this attention has focused on shipments of spent nuclear fuel and high level wastes which, although comprising a very small number of total shipments, constitute a majority of the total curies transported on an annual basis. This report discusses the shipment of these highly radioactive materials

[HIV and the nursing professional in the face of needlestick accidents].

Science.gov (United States)

Vieira, Mariana; Padilha, Maria Itayra Coelho de Souza

2008-12-01

The goal of this study was to identify the scientific production about work-related needlestick accidents among nursing professionals involving HIV-contaminated biological material, as well as to characterize the pre-existing factors to such accidents, such as procedures occurring after the exposure to potentially HIV-contaminated needlestick material. This is a literature review, whose bibliographic search for keywords was carried out within the LILACS databases from the year 2000 onward. This study confirms that pre-existing factors for the occurrence of work-related needlestick accidents are related to work conditions as much as to individual conditions. In face of these accidents, the nursing workers need to know the conducts concerning post-exposure to potentially HIV-contaminated needlestick material. We conclude that the adoption of standardized precautions when working in healthcare is a fundamental condition for worker safety, independently of their area of expertise, given the increasing number of HIV cases.

Ultra-high temperature tensile properties of ODS steel claddings under severe accident conditions

Energy Technology Data Exchange (ETDEWEB)

Yano, Y., E-mail: yano.yasuhide@jaea.go.jp [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki, 311-1393 (Japan); Tanno, T.; Oka, H.; Ohtsuka, S.; Inoue, T.; Kato, S.; Furukawa, T.; Uwaba, T.; Kaito, T. [Japan Atomic Energy Agency, 4002, Narita-cho, Oarai-machi, Ibaraki, 311-1393 (Japan); Ukai, S.; Oono, N. [Materials Science and Engineering, Faculty of Engineering, Hokkaido University, N13, W-8, Kita-ku, Sapporo, Hokkaido, 060-8628 (Japan); Kimura, A. [Institute of Advanced Energy, Kyoto University, Gokasho, Uji, Kyoto 611-0011 (Japan); Hayashi, S. [Tokyo Institute of Technology, 2-12-1, Ookayama, Meguro-ku, Tokyo 152-8550 (Japan); Torimaru, T. [Nippon Nuclear Fuel Development Co., Ltd., 2163, Narita-cho, Oarai-machi, Ibaraki, 311-1313 (Japan)

2017-04-15

Ultra-high temperature ring tensile tests were performed to investigate the tensile behavior of oxide dispersion strengthened (ODS) steel claddings and wrapper materials under severe accident conditions with temperatures ranging from room temperature to 1400 °C which is close to the melting point of core materials. The experimental results showed that the tensile strength of 9Cr-ODS steel claddings was highest in the core materials at ultra-high temperatures of 900–1200 °C, but there was significant degradation in the tensile strength of 9Cr-ODS steel claddings above 1200 °C. This degradation was attributed to grain boundary sliding deformation with γ/δ transformation, which is associated with reduced ductility. By contrast, the tensile strength of recrystallized 12Cr-ODS and FeCrAl-ODS steel claddings retained its high value above 1200 °C, unlike the other tested materials.

Ultra-high temperature tensile properties of ODS steel claddings under severe accident conditions

Science.gov (United States)

Yano, Y.; Tanno, T.; Oka, H.; Ohtsuka, S.; Inoue, T.; Kato, S.; Furukawa, T.; Uwaba, T.; Kaito, T.; Ukai, S.; Oono, N.; Kimura, A.; Hayashi, S.; Torimaru, T.

2017-04-01

Ultra-high temperature ring tensile tests were performed to investigate the tensile behavior of oxide dispersion strengthened (ODS) steel claddings and wrapper materials under severe accident conditions with temperatures ranging from room temperature to 1400 °C which is close to the melting point of core materials. The experimental results showed that the tensile strength of 9Cr-ODS steel claddings was highest in the core materials at ultra-high temperatures of 900-1200 °C, but there was significant degradation in the tensile strength of 9Cr-ODS steel claddings above 1200 °C. This degradation was attributed to grain boundary sliding deformation with γ/δ transformation, which is associated with reduced ductility. By contrast, the tensile strength of recrystallized 12Cr-ODS and FeCrAl-ODS steel claddings retained its high value above 1200 °C, unlike the other tested materials.

História e psicologia em Henri Berr

OpenAIRE

Waeny, Maria Fernanda Costa

2017-01-01

O artigo aborda algumas das idéias de Henri Berr; trata de sua proposta em história, especialmente no que ela se opõe à filosofia da história e à história alemãs; e examina como esta concepção de história à la francesa introduz a psicologia nas pesquisas em história e inaugura a psicologia histórica.Palavras-chave: História da Psicologia; Psicologia Histórica; História das Ciências Humanas; História das Idéias; Annales

Design features of ACR in severe accident mitigation

International Nuclear Information System (INIS)

Shapiro, H.; Krishnan, V.S.; Santamaura, P.; Lekakh, B.; Blahnik, C.

2007-01-01

New reactor designs require the evaluation of design alternatives to reduce the radiological risk by preventing severe accidents or by limiting releases from the plant in the event of such accidents. The Advanced CANDU Reactor TM (ACR TM ) design has provisions to prevent and mitigate severe accidents. This paper describes key ACR design features for severe accident mitigation. It provides a high-level overview of the findings to date. Several design provisions have not yet been finalized or decided, but the designers are keenly aware of the SAM concepts and their requirements. The active heat sinks for 'vessels' (i.e., the fuel channels, the calandria vessel, the calandria end-shields and the calandria vault) are all amply capable of dissipating the severe accident heat loads. These heat sinks are designed to be operable under severe accident environmental conditions; however, their operability is yet to be confirmed by assessments. The active heat sinks for the various process vessels are 'backed up' by passive heat sinks (i.e., steaming plus water make-up from the RWS). The supply side of passive heat sinks is simple, rugged, and not vulnerable to failures of plant systems. The importance of the steam relief side is recognized, and the adequate relief capacity will be provided. The passive heat sinks will give the SAM more than 1 day (likely several days) to diagnose the accident and to establish the ultimate heat sinks. The spray system for containment pressure suppression is designed for high reliability and has ample capacity to ensure low containment leakage without external intervention, after which time alternative supply to the sprays can be brought on line manually. The sprays are backed up by the LACs which are assessed for operability following a severe accident. The strong ACR containment will provide a long time of completely passive protection for any severe accident at decay power. Its characteristics are not prone to catastrophic failures. The

JCO criticality accident as POST-LOCA: Poor structure induced loss of organizational control accident

International Nuclear Information System (INIS)

Furuhama, Yutaka

2000-01-01

Some problems in operation and business management of JCO (Japan Nuclear Fuel Conversion Co.) have been studied as background factors of the criticality accident. Open information about business conditions of JCO suggests that the cause of the accident is not so simple as to be attributed only to economic pressure, but includes immanent problems in JCO. We investigate the problems from five viewpoints, organization of safety management, system of operation management, activities for business improvement, risk awareness, and restructuring of business, and discuss the effects and causality of background factors as well as remedies for them. (author)

As teorias da história e a história ensinada no ensino fundamental

Directory of Open Access Journals (Sweden)

Lia Machado Fiuza Fialho

2017-02-01

Full Text Available Resumo: Objetiva discutir as interfaces das teorias da História e a História ensinada no ensino fundamental, com ênfase na “alfabetização histórica” no século XXI. Como metodologia de pesquisa utilizou-se grupo focal, com 21 pesquisadores e professores que atuavam no campo do Ensino de História e História da Educação. Constatou-se que o ensino no século XXI deve propiciar a aprendizagem de maneira contextualizada, relacionando a pessoa, o tempo e o espaço, em uma perspectiva de produção e transformação da sociedade, na qual o aluno é concebido como sujeito histórico inserido no âmbito dialógico-crítico, tendo o professor como um mediador. Palavras-chave: Ensino. História. Correntes teóricas.

2003 RIA R AND D WORKSHOP.

Energy Technology Data Exchange (ETDEWEB)

OZAKI, S.ET AL.

2003-08-26

The 2003 RIA R&D Workshop was held on August 26-28, 2003 at the Four Points Sheraton Hotel in Bethesda, Maryland. This Workshop was chaired by Satoshi Ozaki of BNL and sponsored by the Nuclear Physics Division of DOE, with the help of Oak Ridge Institute for Science and Education (ORISE). The purpose of this workshop was to understand the present status of R&D efforts for RIA, to evaluate the needs for further R&D, and to identify opportunities for international collaborations. The workshop examined and documented the current pre-conceptual design for RIA, identifying areas where decisions on technical options remain. The status of the current RIA R&D program was documented, recognizing areas where efforts were needed in light of what had been learned. The ongoing and planned R&D activities for operating and planned rare-isotope facilities were presented, enabling the workshop to be a venue to develop coordinated R&D efforts of mutual benefit to U.S. and international efforts. The scientific program for the first day (August 26, 2003) consisted mostly of invited talks presented by major research groups involved in RIA and other RI beam facilities. The talks included those covering: Science of RIA and the RIA Facility Performance Requirements; The Reference RIA Facility Pre-CDR design that was used for the NSAC cost exercise (M. Harrison Sub-Panel) in January 2001; New or latest perspectives on the RIA design at ANL & MSU; and RI Beam facility plans and overview of the R&D activities at overseas laboratories. The second day (August 27, 2003) was devoted to contributed talks on continuing R&D, including that which had been supported by DOE RIA R&D funds. The third day (August 28, 2003) began with open panel discussions in the morning, including further input from participants. The panel members discussed the present status of the RIA planning and R&D needs in a closed session for the rest of the day, and then worked on report planning and writing. This Workshop

Accident management insights after the Fukushima Daiichi NPP accident

International Nuclear Information System (INIS)

Degueldre, Didier; Viktorov, Alexandre; Tuomainen, Minna; Ducamp, Francois; Chevalier, Sophie; Guigueno, Yves; Tasset, Daniel; Heinrich, Marcus; Schneider, Matthias; Funahashi, Toshihiro; Hotta, Akitoshi; Kajimoto, Mitsuhiro; Chung, Dae-Wook; Kuriene, Laima; Kozlova, Nadezhda; Zivko, Tomi; Aleza, Santiago; Jones, John; McHale, Jack; Nieh, Ho; Pascal, Ghislain; ); Nakoski, John; Neretin, Victor; Nezuka, Takayoshi; )

2014-01-01

The Fukushima Daiichi nuclear power plant (NPP) accident, that took place on 11 March 2011, initiated a significant number of activities at the national and international levels to reassess the safety of existing NPPs, evaluate the sufficiency of technical means and administrative measures available for emergency response, and develop recommendations for increasing the robustness of NPPs to withstand extreme external events and beyond design basis accidents. The OECD Nuclear Energy Agency (NEA) is working closely with its member and partner countries to examine the causes of the accident and to identify lessons learnt with a view to the appropriate follow-up actions to be taken by the nuclear safety community. Accident management is a priority area of work for the NEA to address lessons being learnt from the accident at the Fukushima Daiichi NPP following the recommendations of Committee on Nuclear Regulatory Activities (CNRA), Committee on the Safety of Nuclear Installations (CSNI), and Committee on Radiation Protection and Public Health (CRPPH). Considering the importance of these issues, the CNRA authorised the formation of a task group on accident management (TGAM) in June 2012 to review the regulatory framework for accident management following the Fukushima Daiichi NPP accident. The task group was requested to assess the NEA member countries needs and challenges in light of the accident from a regulatory point of view. The general objectives of the TGAM review were to consider: - enhancements of on-site accident management procedures and guidelines based on lessons learnt from the Fukushima Daiichi NPP accident; - decision-making and guiding principles in emergency situations; - guidance for instrumentation, equipment and supplies for addressing long-term aspects of accident management; - guidance and implementation when taking extreme measures for accident management. The report is built on the existing bases for capabilities to respond to design basis

Experimental results from containment piping bellows subjected to severe accident conditions. Volume 1, Results from bellows tested in 'like-new' conditions

International Nuclear Information System (INIS)

Lambert, L.D.; Parks, M.B.

1994-09-01

Bellows are an integral part of the containment pressure boundary in nuclear power plants. They are used at piping penetrations to allow relative movement between piping and the containment wall, while minimizing the load imposed on the piping and wall. Piping bellows are primarily used in steel containments; however, they have received limited use in some concrete (reinforced and prestressed) containments. In a severe accident they may be subjected to pressure and temperature conditions that exceed the design values, along with a combination of axial and lateral deflections. A test program to determine the leak-tight capacity of containment penetration bellows is being conducted under the sponsorship of the US Nuclear Regulatory Commission at Sandia National Laboratories. Several different bellows geometries, representative of actual containment bellows, have been subjected to extreme deflections along with pressure and temperature loads. The bellows geometries and loading conditions are described along with the testing apparatus and procedures. A total of thirteen bellows have been tested, all in the 'like-new' condition. (Additional tests are planned of bellows that have been subjected to corrosion.) The tests showed that bellows are capable of withstanding relatively large deformations, up to, or near, the point of full compression or elongation, before developing leakage. The test data is presented and discussed

Behavior of U³Si₂ Fuel and FeCrAl Cladding under Normal Operating and Accident Reactor Conditions

Energy Technology Data Exchange (ETDEWEB)

Gamble, Kyle Allan Lawrence [Idaho National Lab. (INL), Idaho Falls, ID (United States); Hales, Jason Dean [Idaho National Lab. (INL), Idaho Falls, ID (United States); Barani, Tommaso [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pizzocri, Davide [Idaho National Lab. (INL), Idaho Falls, ID (United States); Pastore, Giovanni [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-09-01

As part of the Department of Energy's Nuclear Energy Advanced Modeling and Simulation program, an Accident Tolerant Fuel High Impact Problem was initiated at the beginning of fiscal year 2015 to investigate the behavior of \\usi~fuel and iron-chromium-aluminum (FeCrAl) claddings under normal operating and accident reactor conditions. The High Impact Problem was created in response to the United States Department of Energy's renewed interest in accident tolerant materials after the events that occurred at the Fukushima Daiichi Nuclear Power Plant in 2011. The High Impact Problem is a multinational laboratory and university collaborative research effort between Idaho National Laboratory, Los Alamos National Laboratory, Argonne National Laboratory, and the University of Tennessee, Knoxville. This report primarily focuses on the engineering scale research in fiscal year 2016 with brief summaries of the lower length scale developments in the areas of density functional theory, cluster dynamics, rate theory, and phase field being presented.

[The inadequacy of official classification of work accidents in Brazil].

Science.gov (United States)

Cordeiro, Ricardo

2018-02-19

Traditionally, work accidents in Brazil have been categorized in government documents and legal and academic texts as typical work accidents and commuting accidents. Given the increase in urban violence and the increasingly precarious work conditions in recent decades, this article addresses the conceptual inadequacy of this classification and its implications for the underestimation of work accidents in the country. An alternative classification is presented as an example and a contribution to the discussion on the improvement of statistics on work-related injuries in Brazil.

Performance Analysis Review of Thorium TRISO Coated Particles during Manufacture, Irradiation and Accident Condition Heating Tests

International Nuclear Information System (INIS)

2015-03-01

Thorium, in combination with high enriched uranium, was used in all early high temperature reactors (HTRs). Initially, the fuel was contained in a kernel of coated particles. However, particle quality was low in the 1960s and early 1970s. Modern, high quality, tristructural isotropic (TRISO) fuel particles with thorium oxide and uranium dioxide (UO 2 ) had been manufactured since 1978 and were successfully demonstrated in irradiation and accident tests. In 1980, HTR fuels changed to low enriched uranium UO 2 TRISO fuels. The wide ranging development and demonstration programme was successful, and it established a worldwide standard that is still valid today. During the process, results of the thorium work with high quality TRISO fuel particles had not been fully evaluated or documented. This publication collects and presents the information and demonstrates the performance of thorium TRISO fuels.This publication is an outcome of the technical contract awarded under the IAEA Coordinated Research Project on Near Term and Promising Long Term Options for Deployment of Thorium Based Nuclear Energy, initiated in 2012. It is based on the compilation and analysis of available results on thorium TRISO coated particle performance in manufacturing and during irradiation and accident condition heating tests

Modelling of RPV lower head under core melt severe accident condition using OpenFOAM

International Nuclear Information System (INIS)

Madokoro, Hiroshi; Kretzschmar, Frank; Miassoedov, Alexei

2017-01-01

Although six years have been passed since the tragic severe accident at Fukushima Daiichi, still large uncertainties exist in modeling of core degradation and reactor pressure vessel (RPV) failure. It is extremely important to obtain a better understanding of complex phenomena in the lower head in order to improve accident management measures. The possible failure mode of reactor pressure vessel and its failure time are especially a matter of importance. Thermal behavior of the molten pool can be simulated by the Phase-change Effective Convectivity Model (PECM), which is a distributed-parameter model developed in the Royal Institute of Technology (KTH), Sweden. The model calculates convective currents not using a pure CFD approach but based on so called “characteristic velocities” that are determined by empirical correlations depending on the geometry and physical properties of the molten pool. At the Karlsruhe Institute of Technology (KIT), the PECM has been implemented in the open-source CFD software OpenFOAM in order to receive detailed predictions of a core melt behavior in the RPV lower head under severe accident conditions. An advantage of using OpenFOAM is that it is very flexible to add and modify models and physical properties. In the current work, the solver is extended to couple PECM with a structure analysis model of the vessel wall. The model considers thermal expansion, plasticity, creep and damage. The model and physical properties are based on those implemented in ANSYS. Although the previous implementation had restriction that the amount of and geometry of the melt cannot be changed, our coupled model allows flexibility of the melt amount and geometry. The extended solver was used to simulate the LIVE-L1 and -L7V experiments and has demonstrated good prediction of the temperature distribution in the molten pool and heat flux distribution through the vessel wall. Regarding the vessel failure the model was applied to one of the FOREVER tests

Design and Development of a Severe Accident Training System

International Nuclear Information System (INIS)

Kim, Ko Ryu; Park, Sun Hee; Kim, Dong Ha

2005-01-01

The nuclear plants' severe accidents have two big characteristics. One is that they are very rare accidents, and the other is that they bring extreme conditions such as the high pressure and temperature in their process. It is, therefore, very hard to get the severe accident data, without inquiring that the data should be real or experimental. In fact, most of severe accident analyses rely on the simulation codes where almost all severe accident knowledge is contained. These codes are, however, programmed by the Fortran language, so that their output are typical text files which are very complicated. To avoid this kind of difficulty in understanding the code output data, several kinds of graphic user interface (GUI) programs could be developed. In this paper, we will introduce a GUI system for severe accident management and training, partly developed and partly in design stage

Transportation accidents/incidents involving radioactive materials (1971--1991)

International Nuclear Information System (INIS)

Cashwell, C.E.; McClure, J.D.

1992-01-01

The Radioactive Materials Incident Report (RMIR) database contains information on transportation-related accidents and incidents involving radioactive materials that have occurred in the United States. The RMIR was developed at Sandia National Laboratories (SNL) to support its research and development program efforts for the US Department of Energy (DOE). This paper will address the following topics: background information on the regulations and process for reporting a hazardous materials transportation incident, overview data of radioactive materials transportation accidents and incidents, and additional information and summary data on how packagings have performed in accident conditions

Chernobyl accident: Causes, consequences and problems of radiation measurements

International Nuclear Information System (INIS)

Kortov, V.; Ustyantsev, Yu.

2013-01-01

General description of Chernobyl accident is given in the review. The accident causes are briefly described. Special attention is paid to radiation situation after the accident and radiation measurements problems. Some data on Chernobyl disaster are compared with the corresponding data on Fukushima accident. It is noted that Chernobyl and Fukushima lessons should be taken into account while developing further measures on raising nuclear industry safety. -- Highlights: ► The short comparative analysis of accidents at Chernobyl and Fukushima is given. ► We note the great effect of β-radiation on the radiation situation at Chernobyl. ► We discuss the problems of radiation measurements under these conditions. ► The impact of shelter on the radiation situation near Chernobyl NPS is described

SSYST. A code system to analyze LWR fuel rod behavior under accident conditions

International Nuclear Information System (INIS)

Gulden, W.; Meyder, R.; Borgwaldt, H.

1982-01-01

SSYST (Safety SYSTem) is a modular system to analyze the behavior of light water reactor fuel rods and fuel rod simulators under accident conditions. It has been developed in close cooperation between Kernforschungszentrum Karlsruhe (KfK) and the Institut fuer Kerntechnik und Energiewandlung (IKE), University Stuttgart, under contract of Projekt Nukleare Sicherheit (PNS) at KfK. Although originally aimed at single rod analysis, features are available to calculate effects such as blockage ratios of bundles and wholes cores. A number of inpile and out-of-pile experiments were used to assess the system. Main differences versus codes like FRAP-T with similar applications are (1) an open-ended modular code organisation, (2) availability of modules of different sophistication levels for the same physical processes, and (3) a preference for simple models, wherever possible. The first feature makes SSYST a very flexible tool, easily adapted to changing requirements; the second enables the user to select computational models adequate to the significance of the physical process. This leads together with the third feature to short execution times. The analysis of transient rod behavior under LOCA boundary conditions e.g. takes 2 mins cpu-time (IBM-3033), so that extensive parametric studies become possible

Severe accident analysis and management in nuclear fuel cycle facilities

International Nuclear Information System (INIS)

Golshan, Mina

2013-01-01

Within the UK regulatory regime, assessment of risks arising from licensee's activities are expected to cover both normal operations and fault conditions. In order to establish the safety case for fault conditions, fault analysis is expected to cover three forms of analysis: design basis analysis (DBA), probabilistic safety assessment (PSA) and severe accident analysis (SAA). DBA should provide a robust demonstration of the fault tolerance of the engineering design and the effectiveness of the safety measures on a conservative basis. PSA looks at a wider range of fault sequences (on a best estimate basis) including those excluded from the DBA. SAA considers significant but unlikely accidents and provides information on their progression and consequences, within the facility, on the site and off site. The assessment of severe accidents is not limited to nuclear power plants and is expected to be carried out for all plant states where the identified dose targets could be exceeded. This paper sets out the UK nuclear regulatory expectation on what constitutes a severe accident, irrespective of the type of facility, and describes characteristics of severe accidents focusing on nuclear fuel cycle facilities. Key rules in assessment of severe accidents as well as the relationship to other fault analysis techniques are discussed. The role of SAA in informing accident management strategies and offsite emergency plans is covered. The paper also presents generic examples of scenarios that could lead to severe accidents in a range of nuclear fuel cycle facilities. (authors)

Use of analytical aids for accident management

International Nuclear Information System (INIS)

Ward, L.W.

1991-01-01

The use of analytical aids by utility technical support teams can enhance the staff's ability to manage accidents. Since instrumentation is exposed to environments beyond design-basis conditions, instruments may provide ambiguous information or may even fail. While it is most likely that many instruments will remain operable, their ability to provide unambiguous information needed for the management of beyond-design-basis events and severe accidents is questionable. Furthermore, given these limitation in instrumentation, the need to ascertain and confirm current plant status and forecast future behavior to effectively manage accidents at nuclear facilities requires a computational capability to simulate the thermal and hydraulic behavior in the primary, secondary, and containment systems. With the need to extend the current preventive approach in accident management to include mitigative actions, analytical aids could be used to further enhance the current capabilities at nuclear facilities. This need for computational or analytical aids is supported based on a review of the candidate accident management strategies discussed in NUREG/CR-5474. Based on the review of the NUREG/CR-5474 strategies, two major analytical aids are considered necessary to support the implementation and monitoring of many of the strategies in this document. These analytical aids include (1) An analytical aid to provide reactor coolant and secondary system behavior under LOCA conditions. (2) An analytical aid to predict containment pressure and temperature response with a steam, air, and noncondensable gas mixture present

Unavoidable Accident

OpenAIRE

Grady, Mark F.

2009-01-01

In negligence law, "unavoidable accident" is the risk that remains when an actor has used due care. The counterpart of unavoidable accident is "negligent harm." Negligence law makes parties immune for unavoidable accident even when they have used less than due care. Courts have developed a number of methods by which they "sort" accidents to unavoidable accident or to negligent harm, holding parties liable only for the latter. These sorting techniques are interesting in their own right and als...

Memória e cidadania nos acervos de história oral e mídia digital

OpenAIRE

Goulart, Elias Estevão; Perazzo, Priscila Ferreira; Lemos, Vilma

2010-01-01

Este texto tem como proposta discutir a importância da constituição de acervos de história oral, levando em consideração a difusão da memória e o exercício da cidadania a partir dela, bem como as relações de poder envolvidas nesse processo. As técnicas de história oral possibilitam a organização de um acervo de relatos de história de vida que, no seu conjunto, levam à recuperação da identidade coletiva e da memória da comunidade. São os sentimentos de pertencimento a um grupo, garantindo por ...

Multiscale Multiphysics Developments for Accident Tolerant Fuel Concepts

International Nuclear Information System (INIS)

Gamble, K. A.; Hales, J. D.; Yu, J.; Zhang, Y.; Bai, X.; Andersson, D.; Patra, A.; Wen, W.; Tome, C.; Baskes, M.; Martinez, E.; Stanek, C. R.; Miao, Y.; Ye, B.; Hofman, G. L.; Yacout, A. M.; Liu, W.

2015-01-01

U 3 Si 2 and iron-chromium-aluminum (Fe-Cr-Al) alloys are two of many proposed accident-tolerant fuel concepts for the fuel and cladding, respectively. The behavior of these materials under normal operating and accident reactor conditions is not well known. As part of the Department of Energy's Accident Tolerant Fuel High Impact Problem program significant work has been conducted to investigate the U 3 Si 2 and FeCrAl behavior under reactor conditions. This report presents the multiscale and multiphysics effort completed in fiscal year 2015. The report is split into four major categories including Density Functional Theory Developments, Molecular Dynamics Developments, Mesoscale Developments, and Engineering Scale Developments. The work shown here is a compilation of a collaborative effort between Idaho National Laboratory, Los Alamos National Laboratory, Argonne National Laboratory and Anatech Corp.

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation

International Nuclear Information System (INIS)

Tentner, A.M.; Parma, E.; Wei, T.; Wigeland, R.

2010-01-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Severe accident approach - final report. Evaluation of design measures for severe accident prevention and consequence mitigation.

Energy Technology Data Exchange (ETDEWEB)

Tentner, A. M.; Parma, E.; Wei, T.; Wigeland, R.; Nuclear Engineering Division; SNL; INL

2010-03-01

An important goal of the US DOE reactor development program is to conceptualize advanced safety design features for a demonstration Sodium Fast Reactor (SFR). The treatment of severe accidents is one of the key safety issues in the design approach for advanced SFR systems. It is necessary to develop an in-depth understanding of the risk of severe accidents for the SFR so that appropriate risk management measures can be implemented early in the design process. This report presents the results of a review of the SFR features and phenomena that directly influence the sequence of events during a postulated severe accident. The report identifies the safety features used or proposed for various SFR designs in the US and worldwide for the prevention and/or mitigation of Core Disruptive Accidents (CDA). The report provides an overview of the current SFR safety approaches and the role of severe accidents. Mutual understanding of these design features and safety approaches is necessary for future collaborations between the US and its international partners as part of the GEN IV program. The report also reviews the basis for an integrated safety approach to severe accidents for the SFR that reflects the safety design knowledge gained in the US during the Advanced Liquid Metal Reactor (ALMR) and Integral Fast Reactor (IFR) programs. This approach relies on inherent reactor and plant safety performance characteristics to provide additional safety margins. The goal of this approach is to prevent development of severe accident conditions, even in the event of initiators with safety system failures previously recognized to lead directly to reactor damage.

Improvement of Severe Accident Analysis Computer Code and Development of Accident Management Guidance for Heavy Water Reactor

International Nuclear Information System (INIS)

Park, Soo Yong; Kim, Ko Ryu; Kim, Dong Ha; Kim, See Darl; Song, Yong Mann; Choi, Young; Jin, Young Ho

2005-03-01

The objective of the project is to develop a generic severe accident management guidance(SAMG) applicable to Korean PHWR and the objective of this 3 year continued phase is to construct a base of the generic SAMG. Another objective is to improve a domestic computer code, ISAAC (Integrated Severe Accident Analysis code for CANDU), which still has many deficiencies to be improved in order to apply for the SAMG development. The scope and contents performed in this Phase-2 are as follows: The characteristics of major design and operation for the domestic Wolsong NPP are analyzed from the severe accident aspects. On the basis, preliminary strategies for SAM of PHWR are selected. The information needed for SAM and the methods to get that information are analyzed. Both the individual strategies applicable for accident mitigation under PHWR severe accident conditions and the technical background for those strategies are developed. A new version of ISAAC 2.0 has been developed after analyzing and modifying the existing models of ISAAC 1.0. The general SAMG applicable for PHWRs confirms severe accident management techniques for emergencies, provides the base technique to develop the plant specific SAMG by utility company and finally contributes to the public safety enhancement as a NPP safety assuring step. The ISAAC code will be used inevitably for the PSA, living PSA, severe accident analysis, SAM program development and operator training in PHWR

Improvement of Severe Accident Analysis Computer Code and Development of Accident Management Guidance for Heavy Water Reactor

Energy Technology Data Exchange (ETDEWEB)

Park, Soo Yong; Kim, Ko Ryu; Kim, Dong Ha; Kim, See Darl; Song, Yong Mann; Choi, Young; Jin, Young Ho

2005-03-15

The objective of the project is to develop a generic severe accident management guidance(SAMG) applicable to Korean PHWR and the objective of this 3 year continued phase is to construct a base of the generic SAMG. Another objective is to improve a domestic computer code, ISAAC (Integrated Severe Accident Analysis code for CANDU), which still has many deficiencies to be improved in order to apply for the SAMG development. The scope and contents performed in this Phase-2 are as follows: The characteristics of major design and operation for the domestic Wolsong NPP are analyzed from the severe accident aspects. On the basis, preliminary strategies for SAM of PHWR are selected. The information needed for SAM and the methods to get that information are analyzed. Both the individual strategies applicable for accident mitigation under PHWR severe accident conditions and the technical background for those strategies are developed. A new version of ISAAC 2.0 has been developed after analyzing and modifying the existing models of ISAAC 1.0. The general SAMG applicable for PHWRs confirms severe accident management techniques for emergencies, provides the base technique to develop the plant specific SAMG by utility company and finally contributes to the public safety enhancement as a NPP safety assuring step. The ISAAC code will be used inevitably for the PSA, living PSA, severe accident analysis, SAM program development and operator training in PHWR.

Memórias de uma história de um leitor

Directory of Open Access Journals (Sweden)

José Roberto Andrade Féres

2014-07-01

Full Text Available http://dx.doi.org/10.5007/1807-9288.2014v10n1p116 Entre histórias e estórias, entre origens e a “quimera da origem” (Michel Foucault, entre memórias e esquecimentos, entre arquivar e deletar, entre formatar e transformar, entre livros e e-books, entre leitores e leitores de e-books, entre palimpsestos e touchscreens, entre ensaio e relato, entre o que falta e o que excede, entre o que se veste com letras e o que se despe literalmente – este texto: trazendo à lembrança Peter Stallybrass (sobretudo “A vida social das coisas” e “O casaco de Marx”, palavras que buscam tratar as pessoas como coisas e as coisas como pessoas, biografando alguns leitores a partir da biografia de um leitor de e-books, e vice-versa.

OSSA - An optimized approach to severe accident management: EPR application

International Nuclear Information System (INIS)

Sauvage, E. C.; Prior, R.; Coffey, K.; Mazurkiewicz, S. M.

2006-01-01

There is a recognized need to provide nuclear power plant technical staff with structured guidance for response to a potential severe accident condition involving core damage and potential release of fission products to the environment. Over the past ten years, many plants worldwide have implemented such guidance for their emergency technical support center teams either by following one of the generic approaches, or by developing fully independent approaches. There are many lessons to be learned from the experience of the past decade, in developing, implementing, and validating severe accident management guidance. Also, though numerous basic approaches exist which share common principles, there are differences in the methodology and application of the guidelines. AREVA/Framatome-ANP is developing an optimized approach to severe accident management guidance in a project called OSSA ('Operating Strategies for Severe Accidents'). There are still numerous operating power plants which have yet to implement severe accident management programs. For these, the option to use an updated approach which makes full use of lessons learned and experience, is seen as a major advantage. Very few of the current approaches covers all operating plant states, including shutdown states with the primary system closed and open. Although it is not necessary to develop an entirely new approach in order to add this capability, the opportunity has been taken to develop revised full scope guidance covering all plant states in addition to the fuel in the fuel building. The EPR includes at the design phase systems and measures to minimize the risk of severe accident and to mitigate such potential scenarios. This presents a difference in comparison with existing plant, for which severe accidents where not considered in the design. Thought developed for all type of plants, OSSA will also be applied on the EPR, with adaptations designed to take into account its favourable situation in that field

Domino effect in chemical accidents: main features and accident sequences

OpenAIRE

Casal Fàbrega, Joaquim; Darbra Roman, Rosa Maria

2010-01-01

The main features of domino accidents in process/storage plants and in the transportation of hazardous materials were studied through an analysis of 225 accidents involving this effect. Data on these accidents, which occurred after 1961, were taken from several sources. Aspects analyzed included the accident scenario, the type of accident, the materials involved, the causes and consequences and the most common accident sequences. The analysis showed that the most frequent causes a...

Consideration of Command and Control Performance during Accident Management Process at the Nuclear Power Plant

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Nisrene M. [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Kim, Sok Chul [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2015-10-15

The accident at the Fukushima Daiichi nuclear power plants shifted the nuclear safety paradigm from risk management to on-site management capability during a severe accident. The kernel of on-site management capability during an accident at a nuclear power plant is situation awareness and agility of command and control. However, little consideration has been given to accident management. After the events of September 11, 2001 and the catastrophic Fukushima nuclear disaster, agility of command and control has emerged as a significant element for effective and efficient accident management, with many studies emphasizing accident management strategies, particularly man-machine interface, which is considered a key role in ensuring nuclear power plant safety during severe accident conditions. This paper proposes a conceptual model for evaluating command and control performance during the accident management process at a nuclear power plant. Communication and information processing while responding to an accident is one of the key issues needed to mitigate the accident. This model will give guidelines for accurate and fast communication response during accident conditions.

[Severe parachuting accident. Analysis of 122 cases].

Science.gov (United States)

Krauss, U; Mischkowsky, T

1993-06-01

Based on a population of 122 severely injured patients the causes of paragliding accidents and the patterns of injury are analyzed. A questionnaire is used to establish a sport-specific profile for the paragliding pilot. The lower limbs (55.7%) and the lower parts of the spine (45.9%) are the most frequently injured parts of the body. There is a high risk of multiple injuries after a single accident because of the tremendous axial power. The standard of equipment is good in over 90% of the cases. Insufficient training and failure to take account of geographical and meteorological conditions are the main determinants of accidents sustained by paragliders, most of whom are young. Nevertheless, 80% of our patients want to continue paragliding. Finally some advice is given on how to prevent paragliding accidents and injuries.

2003 RIA R AND D WORKSHOP

International Nuclear Information System (INIS)

OZAKI, S.

2003-01-01

The 2003 RIA R and D Workshop was held on August 26-28, 2003 at the Four Points Sheraton Hotel in Bethesda, Maryland. This Workshop was chaired by Satoshi Ozaki of BNL and sponsored by the Nuclear Physics Division of DOE, with the help of Oak Ridge Institute for Science and Education (ORISE). The purpose of this workshop was to understand the present status of R and D efforts for RIA, to evaluate the needs for further R and D, and to identify opportunities for international collaborations. The workshop examined and documented the current pre-conceptual design for RIA, identifying areas where decisions on technical options remain. The status of the current RIA R and D program was documented, recognizing areas where efforts were needed in light of what had been learned. The ongoing and planned R and D activities for operating and planned rare-isotope facilities were presented, enabling the workshop to be a venue to develop coordinated R and D efforts of mutual benefit to U.S. and international efforts. The scientific program for the first day (August 26, 2003) consisted mostly of invited talks presented by major research groups involved in RIA and other RI beam facilities. The talks included those covering: Science of RIA and the RIA Facility Performance Requirements; The Reference RIA Facility Pre-CDR design that was used for the NSAC cost exercise (M. Harrison Sub-Panel) in January 2001; New or latest perspectives on the RIA design at ANL and MSU; and RI Beam facility plans and overview of the R and D activities at overseas laboratories. The second day (August 27, 2003) was devoted to contributed talks on continuing R and D, including that which had been supported by DOE RIA R and D funds. The third day (August 28, 2003) began with open panel discussions in the morning, including further input from participants. The panel members discussed the present status of the RIA planning and R and D needs in a closed session for the rest of the day, and then worked on report

Research activities at JAERI on core material behaviour under severe accident conditions

International Nuclear Information System (INIS)

Uetsuka, H.; Katanashi, S.; Ishijima, K.

1996-01-01

At the Japan Atomic Energy Research Institute (JAERI), experimental studies on physical phenomena under the condition of a severe accident have been conducted. This paper presents the progress of the experimental studies on fuel and core materials behaviour such as the thermal shock fracture of fuel cladding due to quenching, the chemical interaction of core materials at high temperatures and the examination of TMI-2 debris. The mechanical behaviour of fuel rod with heavily embrittled cladding tube due to the thermal shock during delayed reflooding have been investigated at the Nuclear Safety Research Reactor (NSSR) of JAERI. A test fuel rod was heated in steam atmosphere by both electric and nuclear heating using the NSSR, then the rod was quenched by reflooding at the test section. Melting of core component materials having relatively low melting points and their eutectic reaction with other materials significantly influence on the degradation and melt down of fuel bundles during severe accidents. Therefore basic information on the reaction of core materials is necessary to understand and analyze the progress of core melting and relocation. Chemical interactions have been widely investigated at high temperatures for various binary systems of core component materials including absorber materials such as Zircaloy/Inconel, Zircaloy/stainless steel, Zircaloy/(Ag-In-Cd), stainless steel B 4 C and Zircaloy/B 4 C. It was found that the reaction generally obeyed a parabolic rate law and the reaction rate was determined for each reaction system. Many debris samples obtained from the degraded core of TMI-2 were transported to JAERI for numerous examinations and analyses. The microstructural examination revealed that the most part of debris was ceramic and it was not homogeneous in a microscopic sense. The thermal diffusivity data was also obtained for the temperature range up to about 1800K. The data from the large scale integral experiments were also obtained through the

Uncertainty analysis of accident notification time and emergency medical service response time in work zone traffic accidents.

Science.gov (United States)

Meng, Qiang; Weng, Jinxian

2013-01-01

Taking into account the uncertainty caused by exogenous factors, the accident notification time (ANT) and emergency medical service (EMS) response time were modeled as 2 random variables following the lognormal distribution. Their mean values and standard deviations were respectively formulated as the functions of environmental variables including crash time, road type, weekend, holiday, light condition, weather, and work zone type. Work zone traffic accident data from the Fatality Analysis Report System between 2002 and 2009 were utilized to determine the distributions of the ANT and the EMS arrival time in the United States. A mixed logistic regression model, taking into account the uncertainty associated with the ANT and the EMS response time, was developed to estimate the risk of death. The results showed that the uncertainty of the ANT was primarily influenced by crash time and road type, whereas the uncertainty of EMS response time is greatly affected by road type, weather, and light conditions. In addition, work zone accidents occurring during a holiday and in poor light conditions were found to be statistically associated with a longer mean ANT and longer EMS response time. The results also show that shortening the ANT was a more effective approach in reducing the risk of death than the EMS response time in work zones. To shorten the ANT and the EMS response time, work zone activities are suggested to be undertaken during non-holidays, during the daytime, and in good weather and light conditions.

Radiation protection issues on preparedness and response for a severe nuclear accident: experiences of the Fukushima accident.

Science.gov (United States)

Homma, T; Takahara, S; Kimura, M; Kinase, S

2015-06-01

Radiation protection issues on preparedness and response for a severe nuclear accident are discussed in this paper based on the experiences following the accident at Fukushima Daiichi nuclear power plant. The criteria for use in nuclear emergencies in the Japanese emergency preparedness guide were based on the recommendations of International Commission of Radiological Protection (ICRP) Publications 60 and 63. Although the decision-making process for implementing protective actions relied heavily on computer-based predictive models prior to the accident, urgent protective actions, such as evacuation and sheltering, were implemented effectively based on the plant conditions. As there were no recommendations and criteria for long-term protective actions in the emergency preparedness guide, the recommendations of ICRP Publications 103, 109, and 111 were taken into consideration in determining the temporary relocation of inhabitants of heavily contaminated areas. These recommendations were very useful in deciding the emergency protective actions to take in the early stages of the Fukushima accident. However, some suggestions have been made for improving emergency preparedness and response in the early stages of a severe nuclear accident. © The Chartered Institution of Building Services Engineers 2014.

Studying Disabling Occupational Accidents in the Construction Industry During Two Years

Directory of Open Access Journals (Sweden)

Ahmad Soltanzadeh

2014-06-01

Full Text Available Background & Objectives : Idnetifying causes of occupational accidents is a key issue to prevent these accidents. The present study aimed to identify and analyze debilitating accidents in the construction industry during a two-year period ( 2010 - 2011 years . Methods: This was an analytical cross-sectional study. The study data included information about all debilitating accidents occurred within two years. Data collection was performed according to the accident report forms in construction sites. Data analysis was performed using SPSS software version 16. The level of significance was considered as P=0.05. Results: The mean age and job experience of injured people were 27.95±6.95 and 2.34±2.00 years, respectively. Most injuries to people were reported in hand (35.4%, legs (28.3% and back (20.4%. Most of accident types were respectively related to slipping and falling (26.1%, throwing objects (21.7%, falls (18.6%, abrasion (16.8% and clash (16.4%. Moreover, the main causes of accidents were related to lack of housekeeping (97.3%, lack of proper training (85.8%, lack of PPE (73.0%, unsafe acts (63.3%, unsafe conditions (32.3% and equipment (22.6%. Conclusion: Analyzing causes of disabling accidents in the construction industry showed that important factors in these accidents included lack of housekeeping, failure to provide proper training, lack of suitable PPE, unsafe acts, unsafe conditions and equipment for the construction jobs

Causes of several accidents in gamma radiography testing units

International Nuclear Information System (INIS)

Vykrocil, L.

1979-01-01

Three cases are described of radiation accidents in gamma flaw-detection work-places in the West Bohemian Region. The causes of the accidents stemmed from the unsatisfactory technical condition of the materials testing equipment used and nonobservance of regulations for work with radioactive sourr.es. It is necessary for precluding similar accident to improve preventive care of gamma flaw-detection equipment and to educate personnel who would be considered for coping with the situation when control over the radiation source is lost. (Ha)

Analytical functions used for description of the plastic deformation process in Zirconium alloys WWER type fuel rod cladding under designed accident conditions

International Nuclear Information System (INIS)

Fedotov, A.

2003-01-01

The aim of this work was to improve the RAPTA-5 code as applied to the analysis of the thermomechanical behavior of the fuel rod cladding under designed accident conditions. The irreversible process thermodynamics methods were proposed to be used for the description of the plastic deformation process in zirconium alloys under accident conditions. Functions, which describe yielding stress dependence on plastic strain, strain rate and temperature may be successfully used in calculations. On the basis of the experiments made and the existent experimental data the dependence of yielding stress on plastic strain, strain rate, temperature and heating rate for E110 alloy was determined. In future the following research work shall be made: research of dynamic strain ageing in E635 alloy under different strain rates; research of strain rate influence on plastic strain in E635 alloy under test temperature higher than 873 K; research of deformation strengthening of E635 alloy under high temperatures; research of heating rate influence n phase transformation in E110 and E635 alloys

A scoping evaluation of severe accidents at Surry and Grand Gulf Nuclear Power Plants resulting from earthquakes during shutdown conditions

International Nuclear Information System (INIS)

Budnitz, R.J.; Davis, P.R.

1991-01-01

This report explores the likelihood of seismic-initiated core damage accidents during refueling shutdown conditions at two nuclear power plants, Surry Unit I and Grand Gulf Unit 1. The effort is scoping in character, and has been performed primarily to establish if a potential problem exists sufficient to justify a more rigorous and more quantitative evaluation. A summary is presented of the important conclusions that have been reached. The most important conclusion is that the core-damage frequencies for earthquake-initiated accidents during shutdown at both Surry Unit I and Grand Gulf Unit I are found to be low in absolute terms. The reasons for this are that in their ability to respond to earthquakes during shutdowns, the plants both have large seismic capacities, well above their design-basis levels; and also that both sites enjoy among the lowest seismic hazards of any LWR sites in the US

Review of progress on enhanced accident tolerant fuel

International Nuclear Information System (INIS)

McCoy, K.; Dunn, B.; Kochendarfer, R.

2015-01-01

The accident at Fukushima has resulted in renewed interest in understanding the performance of nuclear power plants under accident conditions. Part of that interest is directed toward determining how to improve the performance of fuel during an accident that involves long exposures of the fuel to high temperatures. This paper describes the method being used by AREVA to select and evaluate approaches for improving the accident tolerance of nuclear fuel. The method involves starting with a large number of approaches that might enhance accident tolerance, and reviewing how well each approach satisfies a set of engineering requirements and goals. Among the approaches investigated we have the development of fuel pellets that contain a second phase to improve thermal conductivity, the use of molybdenum alloy tubing as fuel cladding, the use of oxidation-resistant coatings to zirconium cladding, and the use of nanoparticles in the coolant to improve heat transfer

Development of systematic models for aerosol agglomeration and spray removal under severe accident conditions

International Nuclear Information System (INIS)

Kajimoto, Mitsuhiro

2008-01-01

Radionuclide behavior during various severe accident conditions has been addressed as one of the important issues to discuss environmental safety in nuclear power plants. The present paper deals with the development of analytical models and their validations for the agglomeration of multiple-component aerosol and spray removal that controls source terms to the environment of both aerosols and gaseous radionuclides during recirculation mode operation in a containment system for a light water reactor. As for aerosol agglomeration, the single collision kernel model that can cover all types of two-body collision of aerosol was developed. In addition, the dynamic model that can treat aerosol and vapor transfer leading to the equilibrium condition under the containment spray operation was developed. The validations of the present models for multiple-component aerosol growth by agglomeration were performed by comparisons with Nuclear Safety Pilot Plant (NSPP) experiments at Oak Ridge National Laboratory (ORNL) and AB experiments at Hanford Engineering National Laboratory (HEDL). In addition, the spray removal models were applied to the analysis of containment spray experiment (CSE) at HEDL. The results calculated by the models showed good agreements with experimental results. (author)

Development of high-performance monitoring system under severe accident condition

International Nuclear Information System (INIS)

Takeuchi, Tomoaki; Tsuchiya, Kunihiro; Ishihara, Masahiro; Komanome, H.; Miura, K.

2017-01-01

A research and development of a monitoring system for NPPs situations even during severe accidents have been performed. The R and D consists of the three objectives. The major findings are briefly summarized in the followings: 1) Radiation-resistant monitoring camera. The image sensor with the photogate and three transistors was found to be advantageous in terms of dark current and sensitivity. In addition, radiation-resistant optical parts and signal circuits were successfully fabricated. The results suggested that the monitoring camera system with 10 6 Gy in radiation resistance was possible. 2) Radiation-resistant in-water wireless transmission system. A two-dimensional LED matrix with 10 6 Gy in radiation resistance and a camera were used as the transmission devices. The results of the in-water transmission tests suggested that stable wireless transmission between 5 m distance was possible even with bubble, turbidity, or obstacles. 3) Heat-resistant signal cable. In order to develop a cable that can transmit the data inside reactor pressure vessels, heat-proof tests were performed for candidate metallic sheath materials of mineral insulation (MI) cables. The results indicated MI cables which can be used at 1000degC in air were possible. These results indicate the feasibility of the monitoring system even during severe accidents. (author)

Safety studies on heat transport and afterheat removal for GCR accident conditions

International Nuclear Information System (INIS)

Hishida, Makoto

1996-01-01

The IAEA coordinated an international research program on 'Heat Transport and Afterheat Removal for GCRs under Accident Conditions (CRP-3)'. America, China, France, Germany, Japan, Netherlands and Russia participate the program. Final goal of the program is to show clearly to the world one of the most important salient features of the HTGR, that is the HTGR reactor can be cooled down by passive measures without causing any damage to the nuclear reactor system even in accidental conditions, and to make clear the boundaries (or restrictions) for the passive cooling regime. The first 5 year term of the coordinate program started in 1993 and established a goal to improve common knowledge for decay heat removal and to improve our tools, like computer codes and analytical models for the prediction of the performance of decay heat removal system. We are now performing benchmark problems for these purposes. The present efforts are concentrated on the benchmark for the passive heat removal performance outside the reactor vessel, partly because we have two different type of the HTGR in the world, the pebble bed type and the block type reactor. They have quite different heat dissipation behavior inside the reactor vessel. However, they have quite similar residual heat removal process outside the reactor vessel. For the first step of the international cooperation, we selected the common problem. After finishing the present benchmark we are planning to proceed to tackle the inside heat removal problem. (J.P.N.)

Indonesian Sea Accident Analysis (Case Study From 2003 – 2013)

Science.gov (United States)

Arya Dewanto, Y.; Faturachman, D.

2018-03-01

There are so many accidents in sea transportation in Indonesia. Most of the accidents happen because of low concern aspects of the safety and security of the crew. In sailing, a man as transport users to interact with the ship and the surrounding environment (including other ships, cruise lines, ports, and the situation of local conditions). These interactions are sometimes very complex and related to various aspects of. Aware of the multiplicity of aspects related to the third of these factors, seeking the safety of cruise through a reduction in the number of accidents and the risk of death and serious injuries due to accidents and goods transported is certainly not enough attempted through mono-sector approach, but rather takes a multi-sector approach to the efforts. In this paper, we described the Indonesian Sea Transportation accident analysis for eleven years divided into four items: total of ship accident type, ship accident factor, total of casualties, region of ship accidents. All data founded from Marine Court (Mahkamah Pelayaran). From that 4 items we can find Indonesia Sea Accident Analysis from 2003-2013.

Containment pressure monitoring method after severe accident in nuclear power plant

International Nuclear Information System (INIS)

Luo Chuanjie; Zhang Shishui

2011-01-01

The containment atmosphere monitoring system in nuclear power plant was designed on the basis of design accident. But containment pressure will increase greatly in a severe accident, and pressure instrument in the containment can't satisfy the monitoring requirement. A new method to monitor the pressure change in the containment after a severe accident was considered, through which accident soften methods can be adopted. Under present technical condition, adding a pressure monitoring channel out of containment for post-severe accident is a considerable method. Daya Bay Nuclear Power Plant implemented this modification, by which the containment release time can be delayed during severe accident, and nuclear safety can be increased. After analysis, this method is safe and feasible. (authors)

[A large-scale accident in Alpine terrain].

Science.gov (United States)

Wildner, M; Paal, P

2015-02-01