Miscibility of amorphous ZrO2-Al2O3 binary alloy

Science.gov (United States)

Zhao, C.; Richard, O.; Bender, H.; Caymax, M.; De Gendt, S.; Heyns, M.; Young, E.; Roebben, G.; Van Der Biest, O.; Haukka, S.

2002-04-01

Miscibility is a key factor for maintaining the homogeneity of the amorphous structure in a ZrO2-Al2O3 binary alloy high-k dielectric layer. In the present work, a ZrO2/Al2O3 laminate thin layer has been prepared by atomic layer chemical vapor deposition on a Si (100) wafer. This layer, with artificially induced inhomogeneity (lamination), enables one to study the change in homogeneity of the amorphous phase in the ZrO2/Al2O3 system during annealing. High temperature grazing incidence x-ray diffraction (HT-XRD) was used to investigate the change in intensity of the constructive interference peak of the x-ray beams which are reflected from the interfaces of ZrO2/Al2O3 laminae. The HT-XRD spectra show that the intensity of the peak decreases with an increase in the anneal temperature, and at 800 °C, the peak disappears. The same samples were annealed by a rapid thermal process (RTP) at temperatures between 700 and 1000 °C for 60 s. Room temperature XRD of the RTP annealed samples shows a similar decrease in peak intensity. Transmission electronic microscope images confirm that the laminate structure is destroyed by RTP anneals and, just below the crystallization onset temperature, a homogeneous amorphous ZrAlxOy phase forms. The results demonstrate that the two artificially separated phases, ZrO2 and Al2O3 laminae, tend to mix into a homogeneous amorphous phase before crystallization. This observation indicates that the thermal stability of ZrO2-Al2O3 amorphous phase is suitable for high-k applications.

Study of directionally solidified eutectic Al2O3-ZrO2(3%Y2O3 doped with TiO2

Directory of Open Access Journals (Sweden)

Peña, J. I.

2007-06-01

Full Text Available An study of directionally grown samples of the eutectic composition in the Al2O3-ZrO2 (3 mol% Y2O3 system, with small TiO2 additions (1 wt%, is presented. The microstructural changes induced by this addition are analysed using SEM (EDX techniques. The mechanical changes, when TiO2 is added, are studied by measuring the flexural strength by three point bending. Also, the toughness is determined by Vickers indentation method. When slow growth rates (10 mm/h are used, interpenetratred and homogeneous microstructure is obtained, independently of the TiO2 doping. When growth rates are higher (300 and 1000 mm/h the structure changes and the phases are organized in form of colonies or cells, which have smaller size when TiO2 is present. This size reduction is accompanied with an increase of the toughness.Este trabajo presenta un estudio de muestras crecidas direccionalmente del sistema Al2O3-ZrO2 (3 mol% Y2O3 en su composición eutéctica con pequeñas adiciones de óxido de titanio (1% de TiO2 en peso. Se analizan los cambios microestructurales inducidos por esta adición mediante SEM (EDX y se estudian los cambios en su comportamiento mecánico medido por flexión en tres puntos, así como la tenacidad de fractura mediante indentación Vickers. Con velocidades lentas de solidificación (10 mm/h se obtiene en ambos casos una microestructura homogénea e interpenetrada, mientras que a velocidades mayores, 300 y 1000 mm/h, se forma una estructura en las que las fases se organizan en forma de colonias o células, siendo éstas de menor tamaño en las muestras dopadas. Esta disminución en el tamaño viene acompañada de un aumento de la tenacidad de fractura medida por indentación.

Thermoluminescent dosimetry of beta radiations of 90 Sr/ 90 Y using ZrO2: Eu

International Nuclear Information System (INIS)

Olvera T, L.; Azorin N, J.; Barrera S, M.; Soto E, A.M.; Rivera M, T.

2005-01-01

In this work the results of studying the thermoluminescent properties (TL) of the doped zirconium oxide with europium (ZrO 2 : Eu 3+ ) before beta radiations of 90 Sr/ 90 Y are presented. The powders of ZrO 2 : Eu 3+ were obtained by means of the sol-gel technique and they were characterized by means of thermal analysis and by X-ray diffraction. The powders of ZrO 2 : Eu 3+ , previously irradiated with beta particles of 90 Sr/ 90 Y, presented a thermoluminescent curve with two peaks at 204 and 292 C respectively. The TL response of the ZrO 2 : Eu 3+ as function of the absorbed dose was lineal from 2 Gy up to 90 Gy. The fading of the information of the ZrO 2 : Eu 3+ was of 10% the first 2 hours remaining almost constant the information by the following 30 days. The ZrO 2 doped with the (Eu 3+ ) ion it was found more sensitive to the beta radiation that the one of zirconium oxide without doping (ZrO 2 ) obtained by the same method. Those studied characteristics allow to propose to the doped zirconium oxide with europium like thermoluminescent dosemeter for the detection of the beta radiation. (Author)

Protocol of thermal treatments for the recovery of tetragonal phase in infrastructures of dental prostheses base of ZrO_2 (3-Y_2O_3) mills in CAD / CAM systems or panthories

International Nuclear Information System (INIS)

Simba, B.G.; Ferreira, B.; Santos, C.

2011-01-01

ZrO_2(3%Y_2O_3) bioceramics are used as dental materials mainly as prosthesis components, because present high mechanical properties and translucence. The use of CAD/CAM machining technique needs final grinding which promotes tetragonal monoclinic transformation reducing the reliability of this ceramic. In this work, ZrO_2(3%Y_2O_3) ceramics were sintered at 1450-0h, 1530-2h or 1600-4h and characterized. Different heat-treatment (400-1200 deg C) are proposed aiming the recuperation of the tetragonal crystalline phase. (author)

Refractories in the Al2O3-ZrO2-SiO2 system

International Nuclear Information System (INIS)

Banerjee, S.P.; Bhadra, A.K.; Sircar, N.R.

1978-01-01

The effect of addition of ZrO 2 in different proportions in the refractories of the Al 2 O 3 -SiO 2 system was studied. The investigation was confined to two broad ranges of compositions incorporating zirconia (15-30 percent and 80-85 percent) in the Al 2 O 3 -ZrO 2 -SiO 2 system. The overall attainment of properties is dependent upon the mode of fabrication and firing, and bears a relationship with the phase assemblages and the relative proportion thereof. Of the different characteristics, the trend of dissociation of zircon has been found to be specially significant vis-a-vis the temperature of firing and thermal shock resistance. Reassociation of the dissociated products has been ascribed to bring forth improved resistance to thermal spalling. The different products developed during this investigation are considered to be very promising which find useful applications in view of the properties attained by them. (auth.)

Effect of ZnO, ZrO2 and B2O3 on clinkerization process. Part I. Clinkerization reactions and clinker composition

Directory of Open Access Journals (Sweden)

Palacios, M.

2008-12-01

Full Text Available The use of clay-based product waste as an alternative prime material in Portland cement raw mixes raises the ZnO, ZrO2 and B2O3 content in the clinker. These compounds are found in the enamelled surface of the tile added to the raw mix. The present study explores the effect of adding 0.5 and 2% ZnO, ZrO2 and B2O3 to the raw mix, separately and jointly, on clinkerization and the distribution and morphology of the mineral phases in the clinker. The findings showed that while ZnO and ZrO2 are fixed in the clinker, B2O3 is partially volatized. Zinc oxide acted as a flux, while neither ZrO2 nor B2O3 increased the molten phase. The addition of the oxides to the raw mix changed the content of the main mineral phases in the clinker. Zinc oxide lowered the C3S and C3A contents, ZrO2 reduced the ferritic phase and B2O3 stabilized C2S. New mineral phases, namely 3CaO·ZnO·2Al2O3 and CaZrO3, were identified in the clinkers obtained when 2% ZnO and ZrO2 were added to the raw mix.El empleo de residuos cerámicos como materia prima alternativa en la fabricación del crudo de cemento Portland, aumenta el contenido de ZnO, ZrO2 y B2O3 en el clinker. Estos elementos se encuentran en la capa esmaltada de los residuos cerámicos incorporados al crudo. Por ello el presente trabajo de investigación aborda el estudio del efecto que tiene la adición en el crudo de contenidos del 0,5 y 2% de ZnO, ZrO2 y B2O3 de manera individual y conjunta en los procesos de clinkerización, en la distribución y morfología de las fases mineralógicas del clinker.Los resultados obtenidos han demostrado que el ZnO y ZrO2 permanecen fijados en el clinker, sin embargo el B2O3 se volatiliza parcialmente. El ZnO actúa como fundente, mientras que el ZrO2 y el B2O3 no aumentan el contenido de fase fundida. La adición de estos óxidos al crudo modifica el contenido de las principales fases mineralógicas del clinker. El ZnO disminuye los contenidos de C3S y C3A, el ZrO2 disminuye

Hydrothermal-precipitation preparation of CdS@(Er3+:Y3Al5O12/ZrO2) coated composite and sonocatalytic degradation of caffeine.

Science.gov (United States)

Huang, Yingying; Wang, Guowei; Zhang, Hongbo; Li, Guanshu; Fang, Dawei; Wang, Jun; Song, Youtao

2017-07-01

Here, we reported a novel method to dispose caffeine by means of ultrasound irradiation combinated with CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ) coated composite as sonocatalyst. The CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ) was synthesized via hydrothermal-precipitation method and then characterized by X-ray diffractometer (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray analysis (EDX) and UV-vis diffuse reflectance spectra (DRS). After that, the sonocatalytic degradation of caffeine in aqueous solution was conducted adopting CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ) and CdS@ZrO 2 coated composites as sonocatalysts. In addition, some influencing factors such as CdS and ZrO 2 molar proportion, caffeine concentration, ultrasonic irradiation time, sonocatalyst dosage and addition of several inorganic oxidants on sonocatalytic degradation of caffeine were investigated by using UV-vis spectra and gas chromatograph. The experimental results showed that the presence of Er 3+ :Y 3 Al 5 O 12 could effectively improve the sonocatalytic degradation activity of CdS@ZrO 2 . To a certain extent some inorganic oxidants can also enhance sonocatalytic degradation of caffeine in the presence of CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ). The best sonocatalytic degradation ratio (94.00%) of caffeine could be obtained when the conditions of 5.00mg/L caffeine, 1.00g/L prepared CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ), 10.00mmol/LK 2 S 2 O 8 , 180min ultrasonic irradiation (40kHz frequency and 50W output power), 100mL total volume and 25-28°C temperature were adopted. It seems that the method of sonocatalytic degradation caused by CdS@(Er 3+ :Y 3 Al 5 O 12 /ZrO 2 ) displayspotentialadvantages in disposing caffeine. Copyright © 2017 Elsevier B.V. All rights reserved.

Difference in Thermal Degradation Behavior of ZrO2 and HfO2 Anodized Capacitors

Science.gov (United States)

Kamijyo, Masahiro; Onozuka, Tomotake; Yoshida, Naoto; Shinkai, Satoko; Sasaki, Katsutaka; Yamane, Misao; Abe, Yoshio

2004-09-01

Microcrystalline ZrO2 and HfO2 thin film capacitors were prepared by anodizing sputter-deposited Zr and Hf films. The thermal degradation behavior of both anodized capacitors was clarified by the measurement of their capacitance properties and Auger depth profiles before and after heat treatment in air. As a result, it is confirmed that the heat-resistance property of the HfO2 anodized capacitor is superior to that of the ZrO2 capacitor. In addition, it is revealed that the thermal degradation of the ZrO2 anodized capacitor is caused by the diffusion of Zr atoms from the underlying layer into the ZrO2 anodized layer, while that of the HfO2 anodized capacitor is caused by the diffusion of oxygen atoms from the anodized layer into the underlying Hf layer.

Interaction of Au with thin ZrO2 films: influence of ZrO2 morphology on the adsorption and thermal stability of Au nanoparticles.

Science.gov (United States)

Pan, Yonghe; Gao, Yan; Kong, Dandan; Wang, Guodong; Hou, Jianbo; Hu, Shanwei; Pan, Haibin; Zhu, Junfa

2012-04-10

The model catalysts of ZrO(2)-supported Au nanoparticles have been prepared by deposition of Au atoms onto the surfaces of thin ZrO(2) films with different morphologies. The adsorption and thermal stability of Au nanoparticles on thin ZrO(2) films have been investigated using synchrotron radiation photoemission spectroscopy (SRPES) and X-ray photoelectron spectroscopy (XPS). The thin ZrO(2) films were prepared by two different methods, giving rise to different morphologies. The first method utilized wet chemical impregnation to synthesize the thin ZrO(2) film through the procedure of first spin-coating a zirconium ethoxide (Zr(OC(2)H(5))(4)) precursor onto a SiO(2)/Si(100) substrate at room temperature followed by calcination at 773 K for 12 h. Scanning electron microscopy (SEM) investigations indicate that highly porous "sponge-like nanostructures" were obtained in this case. The second method was epitaxial growth of a ZrO(2)(111) film through vacuum evaporation of Zr metal onto Pt(111) in 1 × 10(-6) Torr of oxygen at 550 K followed by annealing at 1000 K. The structural analysis with low energy electron diffraction (LEED) of this film exhibits good long-range ordering. It has been found that Au forms smaller particles on the porous ZrO(2) film as compared to those on the ordered ZrO(2)(111) film at a given coverage. Thermal annealing experiments demonstrate that Au particles are more thermally stable on the porous ZrO(2) surface than on the ZrO(2)(111) surface, although on both surfaces, Au particles experience significant sintering at elevated temperatures. In addition, by annealing the surfaces to 1100 K, Au particles desorb completely from ZrO(2)(111) but not from porous ZrO(2). The enhanced thermal stability for Au on porous ZrO(2) can be attributed to the stronger interaction of the adsorbed Au with the defects and the hindered migration or coalescence resulting from the porous structures. © 2012 American Chemical Society

Thermal behavior of the amorphous precursors of the ZrO2-SnO2 system

International Nuclear Information System (INIS)

Stefanic, Goran; Music, Svetozar; Ivanda, Mile

2008-01-01

Thermal behavior of the amorphous precursors of the ZrO 2 -SnO 2 system on the ZrO 2 -rich side of the concentration range, prepared by co-precipitation from aqueous solutions of the corresponding salts, was monitored using differential thermal analysis, X-ray powder diffraction, Raman spectroscopy, field emission scanning electron microscopy (FE-SEM) and energy dispersive X-ray spectrometry (EDS). The crystallization temperature of the amorphous precursors increased with an increase in the SnO 2 content, from 405 deg. C (0 mol% SnO 2 ) to 500 deg. C (40 mol% SnO 2 ). Maximum solubility of Sn 4+ ions in the ZrO 2 lattice (∼25 mol%) occurred in the metastable products obtained upon crystallization of the amorphous precursors. A precise determination of unit-cell parameters, using both Rietveld and Le Bail refinements of the powder diffraction patterns, shows that the incorporation of Sn 4+ ions causes an asymmetric distortion of the monoclinic ZrO 2 lattice. The results of phase analysis indicate that the incorporation of Sn 4+ ions has no influence on the stabilization of cubic ZrO 2 and negligible influence on the stabilization of tetragonal ZrO 2 . Partial stabilization of tetragonal ZrO 2 in products having a tin content above its solid-solubility limit was attributed to the influence of ZrO 2 -SnO 2 surface interactions. In addition to phases closely structurally related to cassiterite, monoclinic ZrO 2 and tetragonal ZrO 2 , a small amount of metastable ZrSnO 4 phase appeared in the crystallization products of samples with 40 and 50 mol% of SnO 2 calcined at 1000 deg. C. Further temperature treatments caused a decrease in and disappearance of metastable phases. The results of the micro-structural analysis show that the sinterability of the crystallization products significantly decreases with an increase in the SnO 2 content

Study on surface defect structures of ZrO2 and some doped ZrO2 by means of work function measurement

International Nuclear Information System (INIS)

Yamawaki, M.; Suzuki, A.; Ono, F.; Yamaguchi, K.

1997-01-01

The work function change of the ZrO 2 +2%Y 2 O 3 sintered pellet, caused by a change of the composition of the sweep gas, was measured using a high temperature Kelvin probe. The Pt reference electrode was calibrated by using ZrO 2 +2%Y 2 O 3 as a standard material. Work function changes of undoped ZrO 2 and Nb-doped ZrO 2 (2%Nb 2 O 5 ) were measured as a function of equilibrium oxygen partial pressure, P O 2 . The thus obtained exponents of P O 2 , 1/n, were 1/6.2 and 1/33.6 for ZrO 2 and ZrO 2 +2%Nb 2 O 5 , respectively. These exponent values were discussed in terms of defect chemistry of the surface layer. (orig.)

Quantitative determination of phases in ZrO2 (MgO) (Y2O3) using the Rietveld method

International Nuclear Information System (INIS)

Castro, Antonio Carlos de

2007-01-01

The key objective of this work is the crystallographic characterization of the zircon co-doped with Yttria and magnesium with the application of the Rietveld method for quantitative phase analysis of zircon polymorph (zircon monoclinic, tetragonal, and cubic). Samples of zircon polymorph were obtained from zircon doped with Yttria and magnesium at defined molar concentrations. The zircon polymorph stability during subeutetoid aging at 1350 deg C were investigated to determine ZrO 2 - MgO - Y 2 0 3 phases degradation and to define the solid solutions stability environment. ZrO 2 powders doped with 8 mol por cent of MgO and 1 mol por cent of Y 2 O 3 , and 9 mol por cent of MgO and 0 mol por cent of Y 2 O 3 have been prepared by chemical route using the co-precipitation method. These samples have been calcinate at 550 deg C, sintered at 1500 deg C and characterized by the Rietveld method using the X-ray diffraction data. The variation of the lattice parameter, changes in the phase composition and their microstructures are discussed. The application of the Rietveld method for quantitative phase analysis of zircon polymorph (zircon tetragonal and cubic) reveals no formation of tetragonal phase and indicating that the matrix is the cubic phase with low concentration of monoclinic phase.(author)

The effect of thermal cycling on tetragonal to monoclinic transformation in ZrO2(2%Y2O3) ceramic studied by high temperature X-ray diffraction

International Nuclear Information System (INIS)

Zhu, W.Z.; Lei, T.C.; Zhou, Y.

1993-01-01

It has been established that brittleness and reliability of ceramics can be improved by a stress-triggered tetragonal (T) to monoclinic (M) transformation in zirconia termed transformation toughening. The T → M transformation is not only influenced by such intrinsic factors as the variety and amount of stabilizers, grain size and morphology of T phase, but can be affected by the cooling rate as well. A previous study by Tsubadin, using a dilation experiment to determine the effect of thermal cycling on the T → M transformation in partially stabilized zirconia suggested that sintering temperature determined the role of thermal cycling, while the underlying cause still remains ambiguous. The intent of the present paper is to reinvestigate the effect of thermal cycling on the T → M transition in a hot pressed ZrO 2 (2%y 2 O 3 ) ceramic, using a high temperature x-ray diffractometer, and rationalize the experimental results from the viewpoint of thermodynamics

The fundamental study for Y2O3 stabilized ZrO2 containing simulated TRU

International Nuclear Information System (INIS)

Kuramoto, Ken-ichi; Kamizono, Hiroshi; Hayakawa, Issei; Muraoka, Susumu; Yanagi, Tadashi.

1991-06-01

Borosilicate glass waste form is considered to be the most suitable material for the immobilization of high-level nuclear waste (HLW). However when the salt-free process on Purex method is adopted and the group partitioning technique of HLW is completely developed, ceramic waste forms which are excellent in thermal stability seem better for the immobilization of hazardous TRU elements. This work is a fundamental study on the solidification of TRU with Y 2 O 3 -stabilized ZrO 2 . In this work, Ce and Nd were used as substitutes for Pu and Am or Cm. TZ-8Y (submicron powder) and designed Ce(NO 3 ) 3 or Nd(NO 3 ) 3 solution were mixed into paste. After dried, the paste was pelletized by the rubber press, and then sintered at 1400degC for 16h. Densities of the sintered pellets were measured and their microstructure was observed by X-ray diffraction and scanning electron microscopy. The results showed that (1) the relative density of ceramic pellet sample was as high as 96.4%, (2) each element was distributed homogeneously and only cubic phase existed. From leach tests in nitric acid and distilled water at 150degC, those ceramic pellet samples showed aqueous corrosion rates which were about 10 2 to 10 3 times lower than that of a glass waste form(PO500). (author)

Investigation of the sinterability of ZrO_2 (Y_2O3_)-bioglass dental ceramics by dilatometry

International Nuclear Information System (INIS)

Bicalho, Luiz de Araujo; Barboza, Miguel Ribeiro Justino; Santos, Claudinei dos; Habibe, Alexandre Fernandes; Magnago, Roberto de Oliveira

2013-01-01

The objective of this work is to study by dilatometry, the liquid phase sintering of ZrO_2 ceramics using bioglass as sintering additive. Y_2 O_3 - stabilized ZrO_2 powders were mixed with 3, 5 and 10 wt% of bioglass with the composition based on 3CaOP_2 O_5 -MgO-SiO_2 system. Specimens were prepared by cold uniaxial pressing under 80MPa and the green relative density was determined. The sintering behavior was studied by measuring the linear shrinkage of samples in a dilatometer in relation to the temperature. The heating and cooling rates used in this study were 10 deg C/min and the maximum sintering temperatures was 1300 deg C with a 120 min isothermal holding time. The results of the shrinkage and shrinkage rates in regard of the sintering temperature and time were related to the amount of bioglass added. The sintered samples were characterized by X-ray diffraction analysis and their relative density. SEM micrographs indicates similar microstructure, and an increase of bioglass content leads to increasing of monoclinic ZrO_2 phase content. The dilatometry results indicate a reduction of the temperature where a maximum shrinkage rate occurs, as function of bioglass increasing. Furthermore, the use of liquid phase reduces the maximum sintering temperature of 1447 deg C to 1250-1280 deg C. (author)

Uncertainty Evaluation of the Thermal Expansion of Gd2O3-ZrO2 with a System Calibration Factor

International Nuclear Information System (INIS)

Park, Chang Je; Kang, Kweon Ho; Na, Sang Ho; Song, Kee Chan

2007-01-01

Both gadolinia (Gd 2 O 3 ) and zirconia (ZrO 2 ) are widely used in the nuclear industry, including a burnable absorber and additives in the fabrication of a simulated fuel. Thermal expansions of a mixture of gadolinia (Gd 2 O 3 ) 20 mol% and zirconia (ZrO 2 ) 80 mol% were measured by using a dilatometer (DIL402C) from room temperature to 1500 .deg. C. Uncertainties in the measurement should be quantified based on statistics. Referring to the ISO (International Organization for Standardization) guide, the uncertainties of the thermal expansion were quantified for three parts - the initial length, the length variation, and the system calibration factor. The whole system, the dilatometer, is composed of many complex sub-systems and in fact it is difficult to consider all the uncertainties of the sub-systems. Thus, the system calibration factor was introduced with a standard material for the uncertainty evaluation. In this study, a new system calibration factor was formulated in a multiplicative way. Further, the effect of calibration factor with random deviation was investigated for the uncertainty evaluation of a thermal expansion

Hot corrosion behavior of nanostructured Gd2O3 doped YSZ thermal barrier coating in presence of Na2SO4 + V2O5 molten salts

Directory of Open Access Journals (Sweden)

Yixiong Wang

2017-08-01

Full Text Available Nickel-based superalloy DZ125 was first sprayed with a NiCrAlY bond coat and followed with a nanostructured 2 mol% Gd2O3−4.5 mol% Y2O3-ZrO2 (2GdYSZ topcoat using air plasma spraying (APS. Hot corrosion behavior of the as-sprayed thermal barrier coatings (TBCs were investigated in the presence of 50 wt% Na2SO4 + 50 wt% V2O5 as the corrosive molten salt at 900 °C for 100 h. The analysis results indicate that Gd doped YVO4 and m-ZrO2 crystals were formed as corrosion products due to the reaction of the corrosive salts with stabilizers (Y2O3, Gd2O3 of zirconia. Cross-section morphology shows that a thin layer called TGO was formed at the bond coat/topcoat interface. After hot corrosion test, the proportion of m-ZrO2 phase in nanostructured 2GdYSZ coating is lower than that of nano-YSZ coating. The result reveals that nanostructured 2GdYSZ coating exhibits a better hot corrosion resistance than nano-YSZ coating.

Compressive strain-dependent bending strength property of Al2O3-ZrO2 (1.5 mol% Y2O3) composites performance by HIP

International Nuclear Information System (INIS)

Reyes-Rojas, A.; Esparza-Ponce, H.; De la Torre, S.D.; Torres-Moye, E.

2009-01-01

Nanometric powders and sintered ceramics of Al 2 O 3 -ZrO 2 (1.5 mol% Y 2 O 3 ) prepared by hot isostatic pressing HIP have been studied. A detailed crystallographic study has been performed through X-ray diffraction, Williamson-Hall method, Rietveld method and high-resolution electron microscopy HREM analysis. The crystallographic structure data, such as domain size, lattice parameters, wt% phase, and micro-strain direction have been obtained using Rietveld refinement and Williamson-Hall methods. The results revealed that the compressive strain (ε) increased from 0.56 to 1.18 (10 -3 ) as the t-ZrO 2 content increased too. The HREM interface study conducted along the [0 0 0 1]Al 2 O 3 ||[0 0 1]ZrO 2 zone axis revealed a micro-strain lattice distortion accumulated at the grain boundary due to the ZrO 2 martensitic phase transformation on cooling, t-ZrO 2 grains coalescence and to the grain growth of α-Al 2 O 3 which cause elongated tetragonal crystals. Micro-strain lattice distortion is adjusted by the shear displacements of the planes (1 1 0) and (11-bar0) along [1-bar10] and [1-bar1-bar0] crystallographic directions, respectively; these planes are arrested by the (101-bar0) alumina plane. In this case, semi-coherent interfaces were observed along the grain boundary. It is verified that the bending strength increased in connection with the strain accumulation and amount of tetragonal structure

Photocatalytic performance of TiO2 catalysts modified by H3PW12O40, ZrO2 and CeO2

Institute of Scientific and Technical Information of China (English)

CAI Tiejun; LIAO Yuchao; PENG Zhenshan; LONG Yunfei; WEI Zongyuan; DENG Qian

2009-01-01

The binary composite photo-catalysts CeO2/TiO2, ZrO2/TiO2 and the ternary composite photo-catalysts H3PW12O40-CeO2/TiO2,H2PW12O40-ZrO2/TiO2 were prepared by sol-gel method. The catalysts were characterized by thermogravimetric-differential thermal analysis (TG-DTA), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The photocatalyfic elimination of methanol was used as model reaction to evaluate the photocatalytic activity of the composite catalysts under ultraviolet light irradiation. The effects of doped content, activation temperature, time, initial concentration of methanol and gas flow rate on the catalytic activity were investigated. The results showed that after doping a certain amount of CeO2 and ZrO2, crystaniTation process of TiO2 was restrained, particles of catalysts are smaller and more uniform. Doping ZrO2 not only significantly improved the catalytic activity, but also increased thermal stability. Doping H3PW12O40 also enhanced the catalytic activity. The catalytic activities of binary and ternary composite photocatalysts were significantly higher than tin-doped TiO2. The dynamics law of photocatalytic reaction over the binary CeO2/TiO2 and ZrO2/TiO2 catalysts has been studied. The activation energy 15.627 and 15.631 kJ/mol and pre-exponential factors 0.5176 and 0.9899 s-1 over each corresponding catalyst were obtained. This reaction accords to the first order dynamics law.

Determination of the UO2-ZrO2-BaO equilibrium diagram

International Nuclear Information System (INIS)

Paschoal, J.O.A.; Kleykanp, H.; Thuemmler, F.

1984-01-01

It is determined the equilibrium diagram of UO 2 - ZrO 2 - BaO to interpret and predict changes in the chemical properties of ceramic (oxide) nuclear fuels during irradiation. The isothermal section of the system at 1700 0 C was determined experimentally, utilizing the techniques of ceramography, X-ray diffraction analysis, microprobe analysis and differential thermal analysis. The solid solubility limits at 1700 0 C between UO 2 and ZrO 2 , UO 2 and BaO, ZrO 2 and BaO, ZrO 2 and BaO and BaUO 3 and BaZrO 3 is presented. The influence of oxygen potential in relation to the different phases is discussed and the phase diagram of the system presented. (M.C.K.) [pt

Synthesis of Y2O3-ZrO2-SiO2 composite coatings on carbon fiber reinforced resin matrix composite by an electro-plasma process

Science.gov (United States)

Zhang, Yuping; Lin, Xiang; Chen, Weiwei; Cheng, Huanwu; Wang, Lu

2016-05-01

In the present paper the Y2O3-ZrO2-SiO2 composite coating was successfully synthesized on carbon fiber reinforced resin matrix composite by an electro-plasma process. The deposition process, microstructures and oxidation resistance of the coatings with different SiO2 concentrations were systematically investigated. A relatively dense microstructure was observed for the Y2O3-ZrO2-SiO2 composite coating with the SiO2 concentration above 5 g/L. The coating exhibited very good oxidation resistance at 1273 K with the mass loss rate as low as ∼30 wt.%, compared to 100 wt.% of the substrate. The formation of the ceramic composites was discussed in detail based on the electrochemical mechanism and the deposition dynamics in order to explain the effect of the plasma discharge. We believe that the electro-plasma process will find wide applications in preparing ceramics and coatings in industries.

Pebble fabrication of super advanced tritium breeders using a solid solution of Li2+xTiO3+y with Li2ZrO3

Directory of Open Access Journals (Sweden)

Tsuyoshi Hoshino

2016-12-01

Full Text Available Lithium titanate with excess lithium (Li2+xTiO3+y is one of the most promising candidates among advanced tritium breeders for demonstration power plant reactors because of its good tritium release characteristics. However, the tritium breeding ratio (TBR of Li2+xTiO3+y is smaller than that of e.g., Li2O or Li8TiO6 because of its lower Li density. Therefore, new Li-containing ceramic composites with both high stability and high Li density have been developed. Thus, this study focused on the development of a solid solution with a new characteristic. The solid-solution pebbles of Li2+xTiO3+y with Li2ZrO3 (Li2+x(Ti,ZrO3+y, designated as LTZO, were fabricated by an emulsion method. The X-ray diffraction patterns of sintered LTZO pebbles are approximately the same as those of Li2+xTiO3+y pebbles, and no peaks attributable to Li2ZrO3 are observed. These results demonstrate that LTZO pebbles are not a two-phase material but rather a solid solution. Furthermore, LTZO pebbles were easily sintered under air. Thus, the LTZO solid solution is a candidate breeder material for super advanced (SA tritium breeders.

Thermoluminescent dosimetry of beta radiations of 90 Sr/ 90 Y using amorphous ZrO2

International Nuclear Information System (INIS)

Rivera M, T.; Olvera T, L.; Azorin N, J.; Barrera R, M.; Soto E, A.M.

2005-01-01

In this work the results of studying the thermoluminescent properties (Tl) of the zirconium oxide in its amorphous state (ZrO 2 -a) before beta radiations of 90 Sr/ 90 Y are presented. The amorphous powders of the zirconium oxide were synthesized by means of the sol-gel technique. The sol-gel process using alkoxides like precursors, is an efficient method to prepare a matrix of zirconium oxide by hydrolysis - condensation of the precursor to form chains of Zr-H 3 and Zr-O 2 . One of the advantages of this technique is the obtention of gels at low temperatures with very high purity and homogeneity. The powders were characterized by means of thermal analysis and by X-ray diffraction. The powders of ZrO 2 -a, previously irradiated with beta particles of 90 Sr/ 90 Y, presented a thermoluminescent curve with two peaks at 150 and 257 C. The dissipation of the information of the one ZrO 2 -a was of 40% the first 2 hours remaining constant the information for the following 30 days. The reproducibility of the information was of ± 2.5% in standard deviation. The studied characteristics allow to propose to the amorphous zirconium oxide as thermoluminescent dosemeter for the detection of beta radiation. (Author)

Characterizing the residual glass in a MgO/Al2O3/SiO2/ZrO2/Y2O3 glass-ceramic

Science.gov (United States)

Seidel, Sabrina; Patzig, Christian; Wisniewski, Wolfgang; Gawronski, Antje; Hu, Yongfeng; Höche, Thomas; Rüssel, Christian

2016-01-01

The non-isochemical crystallization of glasses leads to glass-ceramics in which the chemical composition of the amorphous matrix differs from that of the parent glass. It is challenging to solely analyse the properties of these residual glassy phases because they frequently contain finely dispersed crystals. In this study, the composition of the residual glass matrix after the crystallization of a glass with the mol% composition 50.6 SiO2 · 20.7 MgO · 20.7 Al2O3 · 5.6 ZrO2 · 2.4 Y2O3 is analysed by scanning transmission electron microscopy (STEM) including energy dispersive X-ray analysis (EDXS). A batch of the residual glass with the determined composition is subsequently melted and selected properties are analysed. Furthermore, the crystallization behaviour of this residual glass is studied by X-ray diffraction, scanning electron microscopy including electron backscatter diffraction and STEM-EDXS analyses. The residual glass shows sole surface crystallization of indialite and multiple yttrium silicates while bulk nucleation does not occur. This is in contrast to the crystallization behaviour of the parent glass, in which a predominant bulk nucleation of spinel and ZrO2 is observed. The crystallization of the residual glass probably leads to different crystalline phases when it is in contact to air, rather than when it is enclosed within the microstructure of the parent glass-ceramics. PMID:27734918

Influence of preliminary loading on fracture toughness of ceramics ZrO2-(3,4) mol.% Y2O3

International Nuclear Information System (INIS)

Akimov, G.Ya.; Timchenko, V.M.

2001-01-01

The effect of preliminary mechanical loading on the fracture toughness of ceramics of the ZrO 2 -3-4 mol.% Y 2 O 3 composition is studied. It is shown that the fracture toughness monotonously increases and the increment constitutes ∼ 50% from the initial value. It is supposed that by the preliminary loading there takes place slow isothermal stage of the martensitic phase transformation of the part of the material grains. This leads to increase in the transformation degree by mechanical testing which is expressed in the increase in the fracture toughness [ru

Insights on the High-Temperature Operational Limits of ZrO2-Y2O3 TBCs Manufactured via Air Plasma Spray

Science.gov (United States)

Lima, Rogerio S.; Marple, Basil R.

2017-03-01

The effective high-temperature operation limit of a ZrO2-7-8 wt.%Y2O3 (YSZ) thermal barrier coating (TBC) manufactured via air plasma spray (APS) is considered to be 1300 °C. This is related to the metastable tetragonal t'-phase formed during the rapid quenching of the YSZ particles during spraying. The t'-phase transforms into the equilibrium tetragonal and cubic phases at temperatures ≥ 1300 °C, which can lead to the formation of the monoclinic phase of YSZ upon cooling to room temperature. This formation of the monoclinic phase is accompanied by a volume expansion that leads to TBC failure due to extensive micro-cracking. To further investigate this limitation, an APS YSZ TBC was sprayed on a CMSX-4 substrate. By using a thermal (laser) gradient cyclic testing, a temperature gradient was generated across the TBC/substrate system. The YSZ T- front and substrate backside T- back temperature levels were 1500 and 1000 °C, respectively. In cycle conditions (5-min or 1-h hot and 2-min cool), no TBC failure has been observed. This behavior was partially attributed to the unexpected absence of the monoclinic phase of the YSZ in the cycled coatings. Although preliminary, these results are promising regarding increasing the effective high-temperature operational limits of APS YSZ TBCs.

Density functional theory calculations of the water interactions with ZrO2 nanoparticles Y2O3 doped

Science.gov (United States)

Subhoni, Mekhrdod; Kholmurodov, Kholmirzo; Doroshkevich, Aleksandr; Asgerov, Elmar; Yamamoto, Tomoyuki; Lyubchyk, Andrei; Almasan, Valer; Madadzada, Afag

2018-03-01

Development of a new electricity generation techniques is one of the most relevant tasks, especially nowadays under conditions of extreme growth in energy consumption. The exothermic heterogeneous electrochemical energy conversion to the electric energy through interaction of the ZrO2 based nanopowder system with atmospheric moisture is one of the ways of electric energy obtaining. The questions of conversion into the electric form of the energy of water molecules adsorption in 3 mol% Y2O3 doped ZrO2 nanopowder systems were investigated using the density functional theory calculations. The density functional theory calculations has been realized as in the Kohn-Sham formulation, where the exchange-correlation potential is approximated by a functional of the electronic density. The electronic density, total energy and band structure calculations are carried out using the all-electron, full potential, linear augmented plane wave method of the electronic density and related approximations, i.e. the local density, the generalized gradient and their hybrid approximations.

Atomic-Scale Structure of Al2O3-ZrO2 Mixed Oxides Prepared by Laser Ablation

International Nuclear Information System (INIS)

Yang Xiuchun; Dubiel, M.; Hofmeister, H.; Riehemann, W.

2007-01-01

By means of x-ray diffractometry (XRD) and X-ray absorption fine structure spectroscopy, the phase composition and atomic structure of laser evaporated ZrO2 and ZrO2-Al2O3 nanopowders have been studied. The results indicate that pure ZrO2 exists in the form of tetragonal structure, Al2O3 doped ZrO2 nanoparticles, however, have cubic structure. Compared to bulk tetragonal ZrO2, pure tetragonal ZrO2 nanoparticles have a shorter Zr-O- and Zr-Zr shell, indicating that the lattice contracts with decreasing particle size. For Al2O3 doped ZrO2 solid solution, the distances of first Zr-O and Zr-Zr (Al) coordination decrease with increasing solid solubility. The disorder degree of the ZrO2 lattice increases with increasing solid solubility. The coevaporated ZrO2-Al2O3 is quickly solidified into amorphous phase when it is ablated in a higher pressure. The amorphous phase contains Zr-O-Zr (Al) clusters and has shorter Zr-O distance and tower Zr-O coordination number

Microstructural evolution and stability of tetragonal precipitates in Y2O3 partially-stabilized ZrO2 single crystals

International Nuclear Information System (INIS)

Martinez-Fernandez, J.; Jimenez-Melendo, M.; Dominguez-Rodriguez, A.

1995-01-01

The microstructure and morphology of tetragonal precipitates (t-ZrO 2 ) in yttria partially-stabilized zirconia single crystals containing various amounts of Y 2 O 3 (3, 4, 4.7 and 5.8 mol%) have been studied as a function of aging time at 1,600 C in air. The precipitate size and volume fraction of t-ZrO 2 phase were determined using transmission electron microscopy. The evolution of the precipitate volume fraction with aging time indicated that the precipitation reaction was completed after 24 h of annealing, in agreement with the values of the Y 2 O 3 composition in the matrix measured by analytical electron microscopy. Further aging coarsened the precipitates which joined together forming fiber-like particles of several micrometers in length and remaining untransformed despite their large size. The stability of the t-ZrO 2 precipitates against the tetragonal to monoclinic transformation in the ZrO 2 -Y 2 O 3 system seems to be related to interactions between precipitates due to coherency stresses rather than with their morphological characteristics

Sol-gel route to synthesis of microporous ceramic membranes: Thermal stability of TiO2-ZrO2 mixed oxides

International Nuclear Information System (INIS)

Qunyin Xu; Anderson, M.A.

1993-01-01

In this paper concerning the synthesis of microporous ceramic membranes, the authors focus on the preparation and thermal stability of unsupported microporous TiO 2 -ZrO 2 mixed-oxide membranes. It has been observed that, by adding up to 20% ZrO 2 into TiO 2 or up to 10% TiO 2 into ZrO 2 , these microporous membranes display improved thermal stability. They can be fired up to 500 C for 0.5 h without closing micropores. However, membranes containing almost equal percentages of each component have lost microporous features and have low surface areas and low porosities. A phase diagram of a two-component TiO 2 -ZrO 2 mixed-oxide membrane has been prepared based on DTA and X-ray diffraction data in order to better understand the microstructure changes upon firing

The behavior of ZrO2/20%Y2O3 and Al2O3 coatings deposited on aluminum alloys at high temperature regime

Science.gov (United States)

Pintilei, G. L.; Crismaru, V. I.; Abrudeanu, M.; Munteanu, C.; Baciu, E. R.; Istrate, B.; Basescu, N.

2015-10-01

Aluminum alloy present numerous advantages like lightness, high specific strength and diversity which recommend them to a high number of applications from different fields. In extreme environments the protection of aluminum alloys is difficult and requires a high number of requirements like high temperature resistance, thermal fatigue resistance, corrosion fatigue resistance and galvanic corrosion resistance. To obtain these characteristics coatings can be applied to the surfaces so they can enhance the mechanical and chemical properties of the parts. In this paper two coatings were considered for deposition on an AA2024 aluminum alloy, ZrO2/20%Y2O3 and Al2O3. To obtain a better adherence of the coating to the base material an additional bond layer of NiCr is used. Both the coatings and bond layer were deposited by atmospheric plasma spraying on the samples. The samples were subjected to a temperature of 500 °C and after that slowly cooled to room temperature. The samples were analyzed by electron microscopy and X-ray diffraction to determine the morphological and phase changes that occurred during the temperature exposure. To determine the stress level in the parts due to thermal expansion a finite element analysis was performed in the same conditions as the tests.

Influence of ZrO2 nanoparticles and thermal treatment on the properties of PMMA/ZrO2 hybrid coatings

International Nuclear Information System (INIS)

Reyes-Acosta, M.A.; Torres-Huerta, A.M.; Domínguez-Crespo, M.A.; Flores-Vela, A.I.; Dorantes-Rosales, H.J.; Ramírez-Meneses, E.

2015-01-01

Highlights: • PMMA/ZrO 2 nanocomposites were prepared by melt blending in a single screw extruder. • The nanoparticles of m-, t-ZrO 2 were successfully synthesized using sol–gel technique. • The prepared PMMA/ZrO 2 nanocomposites have better UV protection than pure PMMA. • The thermal stability of the PMMA increases with low amount of ZrO 2 nanoparticles. • PMMA/ZrO 2 nanocomposites show superior values of elastic modulus and hardness. - Abstract: In this work, ZrO 2 nanoparticles were synthesized by the sol–gel method, treated thermally at different temperatures (400, 600 and 800 °C), and added to a polymer matrix in two different weight percentages (0.5 and 1) by single screw extrusion in order to determine the influence of these parameters on the thermal stability and UV radiation resistance of PMMA/ZrO 2 composites. Fourier transform infrared spectroscopy (FT-IR), nuclear magnetic resonance (NMR), X-ray diffraction (XRD), transmission electron microscopy (TEM), confocal laser scanning microscopy (CLSM), ultraviolet–visible spectroscopy (UV–Vis), thermogravimetric analysis (TGA) and nanoindentation techniques were used to evaluate the structural, morphological, optical, thermal and mechanical properties of as-prepared composites. The average crystallite sizes for ZrO 2 sintered at 600 and 800 °C were about 17 and 26 nm, respectively. It was found that the incorporation of a low percentage of ZrO 2 nanoparticles increased the thermal properties of PMMA as well as its hardness and elastic modulus. The degradation temperature at 10 wt.% loss of the PMMA/ZrO 2 (0.5 wt.%, 400 °C) nanocomposite was approximately 48 °C higher than that of pure PMMA. The absorption in the UV region was increased according to the ZrO 2 heat treatment temperature and amount added to the polymer matrix

Radiation shielding with Bi2O3 and ZrO2:Y composites: preparation and characterization

International Nuclear Information System (INIS)

Fontainha, Crissia C.P.

2015-01-01

Despite the benefits of medical imaging examinations, there is a worrying contribution of dose of radiation to population due to the high dose procedures. Procedures as interventional radiology, Computed Tomography (CT) and nuclear medicine provide high doses to the skin of patients, provoking radiation deleterious effects. New attenuators materials have been widely investigated for radiation shielding in those regions of high risk, allowing significant dose reduction near the patient's skin. Composites with Bi 2 O 3 and ZrO 2 :Y metals were obtained by mixing them with P(VDF-TrFe) copolymers from casting. Composites were produced with concentrations of 2, 4 and 8% wt. of Yttrium stabilized zirconia. Bi 2 O 3 containing composites were produced with the same concentrations (2, 4 and 8% wt.), with Bi 2 O 3 particles being previously functionalized with methacrylic acid (MAA). The composites were characterized by FTIR. The entrance skin dose characterization was performed with and without the use of radiation protective shielding. The composite samples were exposed to an absorbed dose of 100 mGy of RQR5 beam quality (70 kV X-ray beam). The attenuation factors, evaluated by XR-QA2 radiochromic films, indicate that both P(VDF-TrFE)/Bi 2 O 3 and P(VDF-TrFE)/ZrO 2 :Y composites are good candidates for use as patient radiation shielding in high dose medical procedures. (author)

Inelastic neutron scattering and lattice dynamics of ZrO2, Y2O3 and ThSiO4

International Nuclear Information System (INIS)

Bose, Preyoshi P.; Mittal, R.; Choudhury, N.; Chaplot, S.L.

2008-01-01

Zirconia (ZrO 2 ), yttria (Y 2 O 3 ) and thorite (ThSiO 4 ) are ceramic materials used for a wide range of industrial applications. The dynamical properties of these materials are of interest as they exhibit numerous interesting phase transitions at high temperature and pressure. Using a combination of inelastic neutron scattering and theoretical lattice dynamics we have studied the phonon spectra and thermodynamic properties of these compounds. The experimental data validate the theoretical model, while the model enables microscopic interpretations of the observed data. The calculated thermodynamic properties are in good agreement with the experimental data. (author)

Thermoluminescence induced by UV radiation in ZrO2-La2O3 and ZrO2-CeO2 mixed systems

International Nuclear Information System (INIS)

Estrada G, R.; Salas C, P.; Mendoza A, D.; Gonzalez, P.R.

2002-01-01

Nowadays, the development of catalytic materials by means of pure or mixed oxides mainly as TiO 2 , Al 2 O 3 , ZrO 2 , La 2 O 3 and CeO 2 used as support or active phases, are widely used in oxidation-reduction reactions in the chemical industry and in petroleum refining processes. the cerium and lanthanum oxides in zircon, have been studied recently in processes for reduction of pollutant gases (SO x , NO x , etc.). They result very interesting for resolving the problems of environmental pollution. Moreover, it has been observed that some of these materials are highly sensitive to ultraviolet radiation (UV), characteristic that can be took in advantage for detecting this type of radiation. In this work the preliminary obtained results on the thermoluminescent response (Tl) induced by the UV radiation in ZrO 2 -La 2 O 3 and ZrO 2 -CeO 2 mixed systems obtained by the sol-gel method are presented. The results show that the first system has a high sensitivity to UV radiation with a Tl curve composed by three peaks, two ones of greater intensity located in 70 and 140 Centigrade degrees. Likewise it was observed that for both materials, the peak located at low temperature is fadeout in few minutes after irradiation, while that the second one peak presented very good stability, resulting promising for dosimetric applications in UV radiation fields. (Author)

The effect of ZrO2 grinding media on the attrition milling of FeAl with Y2O3

International Nuclear Information System (INIS)

Gedevanishvili, S.; Deevi, S.C.

2004-01-01

Attrition milling of water and gas atomized FeAl was carried out with Y 2 O 3 , where ZrO 2 was used as a grinding media in place of stainless steel balls to avoid contamination with Cr and C. Consolidation of the milled powders produced complex FeAl phases containing Zr which doubled the hardness and significantly improved the creep resistance as compared to that of unmilled and consolidated FeAl

Thermal behavior and phase transformation of ZrO2–10%SiO2 precursor powder prepared by a co-precipitation route without adding stability agent

International Nuclear Information System (INIS)

Chu, Hsueh-Liang; Hwang, Weng-Sing; Wang, Cheng-Li; Wang, Moo-Chin; Lee, Kuen-Chan; Huang, Hong-Hsin; Lee, Huey-Er

2014-01-01

Highlights: • The precursor powders contained about 68.3 wt% ZrO 2 , which corresponds to ZrO 2 ·1/8 H 2 O. • The exothermic peak temperature of tetragonal ZrO 2 formation occurred at 1014 K. • The activation energy of ZrO 2 –10%SiO 2 precursors crystallization is 993.7 kJ/mol. • Only the tetragonal ZrO 2 formed when the precursor calcined at 1173–1373 K for 2 h. • As calcined at 1473 K for 2 h, tetragonal ZrO 2 fully converted to monoclinic ZrO 2 . - Abstract: Thermal behavior and phase transformation of ZrO 2 –10%SiO 2 precursor powder prepared by a co-precipitation route without adding stability agent has been studied using different thermal analysis/thermogravimetry (DTA/TG), X-ray diffraction (XRD), transmission electron microscopy (TEM), selected area electron diffraction (SAED), nano beam electron diffraction (NBED), high-resolution TEM (HRTEM) and energy-dispersive X-ray spectrometer (EDS). The TG results show that four weight loss regions were from 298 to 443 K, 443 to 743 K, 743 to 793 K and 793 to 1400 K. The DTA result shows that the ZrO 2 freeze-dried precursor powders crystallization at 1014 K. The activation energy of 993.7 kJ/mol was obtained for tetragonal ZrO 2 crystallization using a non-isothermal process. The XRD result shows that only a single phase of tetragonal ZrO 2 appears when the freeze-dried precursor powders after calcination between 1173 and 1373 K for 2 h. Moreover, when calcined at 1473 K for 2 h, the phase transformation from tetragonal ZrO 2 fully converted to monoclinic ZrO 2 occurred

Theoretical study of methanol synthesis from CO2 and CO hydrogenation on the surface of ZrO2 supported In2O3 catalyst

Science.gov (United States)

Dou, Maobin; Zhang, Minhua; Chen, Yifei; Yu, Yingzhe

2018-06-01

The interactions between ZrO2 support and In2O3 catalyst play pivotal role in the catalytic conversion of CO2 to methanol. Herein, a density functional theory study has been conducted to research the mechanism of methanol synthesis from CO2 and CO hydrogenation on the defective ZrO2 supported In2O3(110) surface (D surface). The calculations reveal that methanol is produced mainly via the HCOO reaction pathway from CO2 hydrogenation on D surface, and the hydrogenation of HCOO to form H2COO species with an activation barrier of 1.21 eV plays the rate determining step for the HCOO reaction pathway. The direct dissociation of CO2 to CO on D surface is kinetically and energetically prohibited. Methanol synthesis from CO hydrogenation on D surface is much facile comparing with the elementary steps involved in CO2 hydrogenation. The rate determining step of CO hydrogenation to methanol is the formation of H3CO species on the vacancy site with a barrier of 0.51 eV. ZrO2 support has significant effect on the suppressing of the dissociation of CO2 and stabilization of H2COO species on the surface of In2O3 catalyst.

Pengaruh NiCrAlY, Ni/Cr2O3/CrxCy Sebagai Variasi Bond Coat Dengan Penambahan Lapisan Al2O3 dan YSZ Pada Inconel 625 Terhadap Struktur Mikro Lapisan Menggunakan Metode Flame Spraying

Directory of Open Access Journals (Sweden)

Aprian Immanuel

2017-01-01

Full Text Available Thermal Barrier Coating (TBC berfungsi untuk mengurangi temperatur substrat serta meningkatkan daya tahannya terhadap korosi dan oksidasi. Pada penelitian ini, digunakan flame spraying dari variasi bond coat (Ni-Cr-Al-Y, (Ni/CrO3/CrXCY dan tanpa bond coat serta melapisi kembali lapisan bond coat dengan Al2O3 dan ZrO2 – 8%Y2O3 sebagai Thermal Barrier Coating untuk diteliti pengaruhnya terhadap struktur mikro lapisan yang terbentuk. Hasil flame spray diamati dengan SEM pada variasi bond coat NiCrAlY ditemukan beberapa serbuk dari material top coat dengan beberapa kondisi yaitu meleleh (melted, meleleh sebagian (semi melted, dan tidak meleleh (unmelted. Ditemukan poros yang merata hampir di seluruh permukaan sampel dan munculnya pengintian retak. Perbedaan sebelum dan sesudah perlakuan ada pada persebaran setiap unsur di setiap spesimen, dan lapisan oksida yang terbentuk pada seluruh variasi bond coat

Thermal Shock Property of Al／Ni-ZrO2 Gradient Thermal Barrier Coatings

Institute of Scientific and Technical Information of China (English)

FANJin-juan; WANGQuan-sheng; ZHANGWei-fang

2004-01-01

Al/Ni-ZrO2 gradient thermal barrier coatings are made on aluminum substrate using plasma spraying method and one direction thermal shock properties of the coatings are studied in this paper. The results show that pores in coatings link to form cracks vertical to coating surface. They go through the whole ZrO2 coating once vertical cracks form. When thermal shock cycles increase, horizontal cracks that result in coatings failure forms in the coatings and interface. And vertical cracks delay appearance of horizontal cracks and enhance thermal shock property of coatings. Failure mechanisms of coating thermal shock are discussed using experiments and finite element method.

Al2TiO5-ZrTiO4-ZrO2 composites

International Nuclear Information System (INIS)

Parker, F.J.

1990-01-01

The characterization and properties of ceramic composites containing the phases Al 2 TiO 5 , ZrTiO 4 , and ZrO 2 are described. The low thermal expansions are apparently due to a combination of microcracking by the titanate phases and a contractive phase transformation by the ZrO 2 . The crystal chemistry and microstructure of the product are processing dependent. Although the composites represent a complex microcracking system, the low thermal expansions and high-temperature stability make them potential candidates for commercial application requiring thermal shock resistance

Non-stoichiometric mullites from Al2O3-SiO2-ZrO2 amorphous materials by rapid quenching

International Nuclear Information System (INIS)

Yoshimura, M.; Hanaue, Y.; Somiya, S.

1990-01-01

In order to study the formation of zirconia dispersed mullite ceramics from homogeneous starting materials hot-pressing and heat-treatments have been carried out for rapidly quenched amorphous materials with 0 to 20 wt% ZrO 2 mullite compositions. These amorphous materials crystallized directly to mullite for 0-10 wt% ZrO 2 samples or mullite + t-ZrO 2 for 20 wt% ZrO 2 at about 970 degrees C. An A1 2 O 3 - rich composition (82 wt% A1 2 O 3 ) and also a significant solid solubility of ZrO 2 (>10 wt%) were estimated for these mullites by XRD studies. Amorphous speres of 10 nm which were considered to be SiO 2 - rich phase were produced by a phase separation in mullite grains

Assessment of solid/liquid equilibria in the (U, Zr)O2+y system

Science.gov (United States)

Mastromarino, S.; Seibert, A.; Hashem, E.; Ciccioli, A.; Prieur, D.; Scheinost, A.; Stohr, S.; Lajarge, P.; Boshoven, J.; Robba, D.; Ernstberger, M.; Bottomley, D.; Manara, D.

2017-10-01

Solid/liquid equilibria in the system UO2sbnd ZrO2 are revisited in this work by laser heating coupled with fast optical thermometry. Phase transition points newly measured under inert gas are in fair agreement with the early measurements performed by Wisnyi et al., in 1957, the only study available in the literature on the whole pseudo-binary system. In addition, a minimum melting point is identified here for compositions near (U0.6Zr0.4)O2+y, around 2800 K. The solidus line is rather flat on a broad range of compositions around the minimum. It increases for compositions closer to the pure end members, up to the melting point of pure UO2 (3130 K) on one side and pure ZrO2 (2970 K) on the other. Solid state phase transitions (cubic-tetragonal-monoclinic) have also been observed in the ZrO2-rich compositions X-ray diffraction. Investigations under 0.3 MPa air (0.063 MPa O2) revealed a significant decrease in the melting points down to 2500 K-2600 K for increasing uranium content (x(UO2)> 0.2). This was found to be related to further oxidation of uranium dioxide, confirmed by X-ray absorption spectroscopy. For example, a typical oxidised corium composition U0.6Zr0.4O2.13 was observed to solidify at a temperature as low as 2493 K. The current results are important for assessing the thermal stability of the system fuel - cladding in an oxide based nuclear reactor, and for simulating the system behaviour during a hypothetical severe accident.

The effect of preliminary hydrolysis on the properties of ZrO2-7% Y2O3 powders prepared by hydroxide precipitation

Science.gov (United States)

Zhirenkina, Nina V.; Mashkovtsev, Maxim A.; Bereskina, Polina A.; Zakirov, Ilsur F.; Baksheev, Evgenie O.; Bujnachev, Sergey V.; Vereshchagin, Artem O.

2017-09-01

In this study, the effect of preliminary hydrolysis of zirconyl oxysulfate on the properties of ZrO2-7 % Y2O3 powders prepared by hydroxides precipitation at a constant pH of 5 was studied. X-ray diffraction analysis showed the monophasic nature of the samples and the insignificant difference between CSR (coherent scattering regions). Samples differed in particle size distribution, porosity and morphology.

Análisis de la zona fundida en el crecimiento del compuesto eutéctico Al2O3-ZrO2(Y2O3 por fusión zonal con láser

Directory of Open Access Journals (Sweden)

Peña, J. I.

2007-10-01

Full Text Available In this work a study of the floating zone during the growth of bars of Al2O3-ZrO2(Y2O3 by the laser floating zone technique is presented. The axial thermal gradient in the solidification interface has been calculated and compared with the experimental one of 6.5*105 K/m. For this calculation the coefficients of heat transference during the solidification process have been determined. The floating zone profile has been also studied and the maximum stable length for the zone determined, verifying the stability criterion established by some authors. The study is completed with an estimation of the laser power necessary to carry out the growth. This value is compared with the measured one during the growth of 2 mm diameter bars.En este trabajo se presenta un estudio de la zona flotante durante el crecimiento de barras de Al2O3-ZrO2 (Y2O3 por la técnica de fusión zonal por láser. Se ha calculado el gradiente térmico axial existente en la intercara de solidificación y comparado con el que se ha medido de forma experimental, siendo éste de 6,5*105 K/m. Para este cálculo se han determinado los coeficientes de transferencia de calor durante el proceso de resolidificación. También se ha estudiado el perfil de la zona flotante y analizado el rango de estabilidad en términos de longitud máxima de zona, verificándose experimentalmente los límites teóricos establecidos por algunos autores. El estudio se completa con una estimación de la potencia necesaria para llevar a cabo el crecimiento confirmando su validez para el caso particular de cilindros de 2 mm de diámetro.

Properties of slip-cast transformation-toughened β''-Al2O3/ZrO2 composites

International Nuclear Information System (INIS)

Green, D.J.; Metcalf, M.G.

1984-01-01

The aim of this study was to fabricate β''-Al 2 O 3 /ZrO 2 composites by an alternative procedure than the dry-pressing route chosen by Lange et al. or Viswanathan et al. and to determine the amount of ZrO 2 that can be used to maximize the fracture toughness without significantly affecting the ionic resistivity. The fabrication technique chosen was that of slip casting, as this approach should allow the ZrO 2 phase to be well dispersed without the detrimental presence of agglomerates, which can act as failure origins in ceramics. Slip casting is a well-established ceramic fabrication technique and is versatile in being able to produce rather complex shapes. It has been used previously to fabricate β-Al 2 O 3 . In the present study, it was decided to perform the slip casting using organic media as water reacts with β''-Al 2 O 3 and leaches out the sodium by ion exchange and can significantly influence the ionic conductivity. It was important, therefore, to identify suitable organic media that could be used to control the dispersion of the β''-Al 2 O 3 and ZrO 2 powders and identify the important processing parameters that would give rise to a fine-grained microstructure in which the ZrO 2 was well dispersed and retained in its tetragonal form

Phase development of the ZrO 2-ZnO system during the thermal treatments of amorphous precursors

Science.gov (United States)

Štefanić, Goran; Musić, Svetozar; Ivanda, Mile

2009-04-01

Thermal behavior of the amorphous precursors of the ZrO 2-ZnO system on the ZrO 2-rich side of the concentration range, co-precipitated from aqueous solutions of the corresponding salts, was monitored using X-ray powder diffraction, Raman spectroscopy, Fourier transform infrared spectroscopy, field emission scanning electron microscopy, energy dispersive X-ray spectrometry, differential scanning calorimetry and thermogravimetric analysis. The crystallization temperature of the amorphous precursors increased with an increase in the ZnO content, from 457 °C (0 mol% ZnO) to 548 °C (25 mol% ZnO). Maximum solubility of Zn 2+ ions in the ZrO 2 lattice (˜25 mol%) occurred in the metastable products obtained upon crystallization of the amorphous precursors. Raman spectroscopy indicates that the incorporation of Zn 2+ ions can partially stabilize only the tetragonal ZrO 2. A precise determination of unit-cell parameters of the t-ZrO 2-type solid solutions, using both Rietveld and Le Bail refinements of the powder diffraction patterns, shows that the increase in the Zn 2+ content causes a decrease in c-ax, which in a solid solution with a Zn 2+ content above 20 mol% approaches very closely a-ax. The thermal treatment of the crystallization products (up to 1000 °C) leads to a rapid decrease in the terminal solid solubility limit of Zn 2+ ions in the ZrO 2 lattice that is followed by the partial evaporation of zinc, the formation of and increase in phases structurally closely related to zincite and monoclinic ZrO 2. The results of micro-structural analysis indicate that the presence of ZnO promotes the sintering of the ZrO 2 crystallization products.

Nanocrystal in Er3+-doped SiO2-ZrO2 Planar Waveguide with Yb3+ Sensitizer

International Nuclear Information System (INIS)

Razaki, N. Iznie; Jais, U. Sarah; Abd-Rahman, M. Kamil; Bhaktha, S. N. B.; Chiasera, A.; Ferrari, M.

2010-01-01

Higher doping of Er 3+ in glass ceramic waveguides would cause concentration and pair-induced quenching which lead to inhomogeneous line-width of luminescence spectrum thus reduce output intensity. Concentration quenching can be overcome by introducing ZrO 2 in the glass matrix while co-doping with Yb 3+ which acts as sensitizer would improve the excitation efficiency of Er 3+ . In this study, SiO 2 -ZrO 2 planar waveguides having composition in mol percent of 70SiO 2 -30ZrO 2 doped with Er 3+ and co-doped with Yb 3+ , were prepared via sol-gel route. Narrower and shaper peaks of PL and XRD shows the formation of nanocrystals. Intensity is increase with addition amount of Yb 3+ shows sensitizing effect on Er 3+ .

Development of AL_2O_3 - ZrO_2 ceramic composite reinforced with rare earth oxides (Y_2O)3) for inert coating of storage and transport systems of crude petroleum

International Nuclear Information System (INIS)

Silva, J.C.; Yadava, Y.P.; Sanguinetti Ferreira, R.A.; Albuquerque, L.T.

2014-01-01

The advancement of the oil sector has generated the need for the use of materials resistant to aggressive environments to oil. Although ceramics have high melting point and high hardness is, on the other hand, more fragile and less tough, which can cause damage to the metal structure. The Al_2O_3 based ceramics reinforced with rare earth oxide can improve tenaciousness and makes the ceramic material more resistant. This article aims to present the production of composite Al_2O_3 - Y_2O_3 stabilized ZrO_2 by uniaxial pressing, following sintering (1200-1350 deg C). Structural and microstructural characterizations as XRD (X-Ray Diffraction) and SEM (Scanning Electron Microscopy) and mechanical tests as Vickers hardness, % absorption and % linear shrinkage were conducted to evaluate the feasibility of using the composite and ceramic coating for storage and transportation of oil tanks. The results indicate that the proportions of 5%, 10% and 30% ZrO_2 make it suitable as a good composite suitable coating. (author)

Sintering of nanopowders of ZrO_2 (Y_2O_3): Effect of compaction pressure on densification

International Nuclear Information System (INIS)

Palmeira, Alexandre Alvarenga; Magnago, Roberto de Oliveira; Pereira, Glayce Cassaro; Bondioli, Marcelo Jose; Strecker, Kurt; Santos, Claudinei dos

2014-01-01

In this work studied the powders (nano) sintered of ZrO_2 (Y_2O_3) by dilatometry. Was identified the effect of compaction pressure variation in the final results of densification of materials. Powders were compacted at different compaction pressures. The compacts were subjected to temperatures of 1250°C to 1400°C with sintering levels ranging from 0 to 8 hours. Samples were characterized by X-ray diffraction and relative density using Archimedes method. The results were compared with powders (micro) of similar composition in order to compare the effect of particle size on densification parameters. The samples were further subjected to microstructural characterization in order to identify the average grain size of the sintering under each condition used in both materials. (author)

Effect of Microstructure on the Thermal Conductivity of Plasma Sprayed Y2O3 Stabilized Zirconia (8% YSZ

Directory of Open Access Journals (Sweden)

Ningning Hu

2017-11-01

Full Text Available In this paper, the effect of microstructure on the thermal conductivity of plasma-sprayed Y2O3 stabilized ZrO2 (YSZ thermal barrier coatings (TBCs is investigated. Nine freestanding samples deposited on aluminum alloys are studied. Cross-section morphology such as pores, cracks, m-phase content, grain boundary density of the coated samples are examined by scanning electron microscopy (SEM and electron back-scattered diffraction (EBSD. Multiple linear regressions are used to develop quantitative models that describe the relationship between the particle parameters, m-phase content and features of the microstructure such as porosity, crack-porosity, and the length density of small and big angle-cracks. Moreover, the relationship between the microstructure and thermal conductivity is investigated. Results reveal that the thermal conductivity of the coating is mainly determined by the microstructure and grain boundary density at room temperature (25 °C, and by the length density of big-angle-crack, monoclinic phase content and grain boundary density at high temperature (1200 °C.

ZrO2 oxygen and hydrogen sensors: A geologic perspective

International Nuclear Information System (INIS)

Ulmer, G.C.

1983-01-01

The geosciences have been attracted to the high accuracy of 5 ZrO 2 cells for both f(O 2 ) and pH sensors. That the very same ZrO 2 membrane can be used above 600 0 C to sense f(O 2 ) and used between 25 0 and 300 0 C (maybe higher) to sense pH has been demonstrated. Specific resistivity measurements for such cells follow the equation log R = -2.20 + 4000/T (for T(K) from 298-1573 K) (for Y 2 O 3 levels of 4-8 mol%). In the lower-temperature regime, i.e., pH sensing, the ZrO 2 cell does not respond to changes in molecular O 2 or H 2 in its environment. Geochemical raw material impurities and ZrO 2 membrane fabrication techniques that affect f(O 2 ) and pH sensing are discussed. The application of ZrO 2 cells to various geologic redox equilibria are demonstrated by a few selected examples

About properties of ZrO2 thermal protective coatings obtained from spherical powder mixtures

Science.gov (United States)

Berdnik, O. B.; Tsareva, I. N.; Tarasenko, Yu P.

2017-05-01

It is developed the technology of high-energy plasma spraying of the zirconium dioxide (ZrO2) thermal protective coating on the basis of ZrO2 tetragonal and cubic phases with the spheroidal grain shape and the columnar substructure, with the total porosity P = 4 %, the hardness HV = 12 GPa, the roughness parameter R a ˜ 6 μm, the thickness 0.3-3 mm. As a sublayer it is used the heat-resistant coating of “Ni-Co-Cr-Al-Y” system with an intermetallic phase composition and the layered microstructure of the grains.

TECHNOLOGICAL PECULIARITIES OF THERMAL BARRIER COATINGS BASED ON ZIRCONIUM DIOXIDE

Directory of Open Access Journals (Sweden)

V. V. Okovity

2016-01-01

Full Text Available A technology for formation of thermal barrier coatings (TBC based on zirconium dioxide has been developed in the paper. The paper investigates structures of phase composition and thermal stability of such developed coatings. Investigation results pertaining to formation of an oxide system ZrO2 – Y2O3, while using plasma spraying and subsequent high-energy processing, which allows to increase resistance of a thermal barrier coating to thermal cycling heat resistance of the coating at temperature of 1100 °C. This leads to longer protection of bottom layer against high-temperature exposure. The methodology is based on complex metallographic, X-ray diffraction and electron microscopy investigations of structural elements in composite plasma coatings of the ZrO2 – Y2O system. Resistance of plasma coatings (Мe – Cr – Al – Y/ZrO2 – Y2O3-type, used as TBC to protect gas turbine engine blades under conditions of frequent thermal cyclings is limited by cleavage of an outer ceramic layer. Structural and electron microprobe investigations have shown that as a result of thermal cycling an outer atmosphere due to porous structure of the ceramic coating layer, migrates to the surface of lower metal coating, causing its oxidation. As a result, the metal-ceramic Al2O3 layer is formed at a metal-ceramic interface and it changes a stress state of the coating that causes a reduction of protective properties. Thus, a high heat resistance of thermal barrier coatings depends on processes occurring at the interface between metal and ceramic coating layers. A laser impact on samples with TBC leads to changes in the structure of the oxide layer of ZrO2 – Y2O3. In this case its initial surface characterized by considerable relief is significantly flattened due to processing and the coating is fractured and it is separated in fragments. As the oxide coating has low thermal conductivity, and the time of laser exposure is about 10–3 sec, a heat flux

Synthesis and cathodoluminescence characterization of ZrO2:Er3+ films

International Nuclear Information System (INIS)

Martínez-Hernández, A.; Guzmán-Mendoza, J.; Rivera-Montalvo, T.; Sánchez-Guzmán, D.; Guzmán-Olguín, J.C.; García-Hipólito, M.; Falcony, C.

2014-01-01

Trivalent erbium doped zirconium oxide films were deposited by the ultrasonic spray pyrolysis technique. Films were deposited using zirconium tetrachloride octahydrate (ZrCl 4 O·8H 2 O) and erbium nitrate hexahydrate ((NO 3 ) 3 Er·6H 2 O) as precursors and deionized water as solvent. The dopant concentrations in the spray solution were 1, 3, 5, 10 and 15 at% in ratio to zirconium content. The films were deposited on corning glass substrates at different temperatures from 400 up to 550 °C. Films deposited at temperatures lower than 400 °C were amorphous, however, as substrate temperatures are increased, the ZrO 2 films presented a better crystallinity and showed a tetragonal phase. Cathodoluminescence (CL) emission spectra showed bands centred at 524, 544 and 655 nm associated with the electronic transition of Er 3+ . - Highlights: • The films of ZrO 2 :Er 3+ were obtained by spray pyrolysis. • Emission spectra of ZrO 2 :Er 3+ films were reported. • Cathodoluminescence of ZrO 2 :Er 3+ films was analyzed. • Cathodoluminescence of ZrO 2 :Er 3+ films showed strong dependence on substrate temperature and electron voltage

White photoluminescence emission from ZrO_2 co-doped with Eu"3"+, Tb"3"+ and Tm"3"+

International Nuclear Information System (INIS)

Lovisa, L.X.; Araújo, V.D.; Tranquilin, R.L.; Longo, E.; Li, M.S.; Paskocimas, C.A.; Bomio, M.R.D.; Motta, F.V.

2016-01-01

The search for high efficiency, reliable, low power consumption and environmental friendly materials for white light-emitting diodes has become a proficient field. Single-phase doped materials have been made to solve some of these challenges. Particles with color-tunable emission can be obtained by a combination of some lanthanide ions in the host material. The luminescence properties and crystalline structure of ZrO_2 particles co-doped with rare earth ions (RE"3"+ = Tb"3"+, Eu"3"+ and Tm"3"+) calcined at different temperatures were studied. We aimed to investigate the emission spectrum of the particles in the red, green, and blue regions under UV excitation. The x and y coordination chromaticity - (x = 0.34, y = 0.34) and (x = 0.31, y = 0.34) - presented values close to those of the white color (x = y = 0.33). In conclusion, the ZrO_2:RE"3"+ powers were successfully obtained by the complex polymerization method and are promising candidates for white light-emitting applications. - Highlights: The ZrO_2:RE materials presented here are promising photoluminescent materials. The CIE coordinates calculated are disposed in the blank region in the CIE diagram. The results for the Raman confirm the response obtained by XRD: stabilization of cubic phase.

Neutron irradiation damage in Al2O3 and Y2O3

International Nuclear Information System (INIS)

Clinard, F.W. Jr.; Bunch, J.M.; Ranken, W.A.

1975-01-01

Two ceramics under consideration for use in fusion reactors, Al 2 O 3 and Y 2 O 3 , were irradiated in the EBR-II fission reactor at 650, 875, and 1025 0 K to fluences between 2 and 6 x 10 21 n/cm 2 (E greater than 0.1 MeV). Samples evaluated include sapphire, Lucalox, alumina, Y 2 O 3 , and Y 2 O 3 -10 percent ZrO 2 (Yttralox). All Al 2 O 3 specimens swelled significantly (1 to 3 percent), with most of the growth observed in sapphire along the c-axis at the higher temperatures. Al 2 O 3 samples irradiated at 875 to 1025 0 K contained a high density of small aligned ''pores''. Irradiated Y 2 O 3 -based ceramics exhibited dimensional stability and a defect content consisting primarily of unresolved damage and/or dislocation loops. The behavior of these ceramics under irradiation is discussed, and the relevance of fission neutron damage studies to fusion reactor applications is considered. (auth)

Studies on powder processing and sintering behaviour of ZrO2-9.0 mol% Y2O3 ceramics

International Nuclear Information System (INIS)

Ghosh, A.; Gonal, M.R.; Upadhyaya, D.D.; Ram Prasad

1998-01-01

In the present investigation the synthesis and densification behaviour of ZrO 2 -9.0 mol% Y 2 O 3 ceramics has been described. Powder preparation was based on the co-precipitation method. It was found that variation in the precipitation conditions and washing steps of the precipitated gels resulted in powder of different agglomerate sizes. The effect of different precipitations and washing conditions on the crystallite size of the 600 deg C calcined powders were examined by x-ray diffraction. The powders produced were essentially of the cubic fluorite phase. The ball-milled powders were analyzed for particle size distribution. Densification behaviour of the bodies made by slip casting has also been studied. (author)

Strength-toughness relations in sintered and isostatically hot-pressed ZrO2-toughened Al2O3

International Nuclear Information System (INIS)

Hori, S.; Yoshimura, M.; Somiya, S.

1986-01-01

The fracture toughness of fine-grained undoped ZrO 2 -toughened Al 2 O 3 (ZTA) was essentially unchanged by post-sintering hot isostatic pressing and increased monotonically with ZrO 2 additions up to 25 wt%. The strength of ZTA with 5 to 15 wt% tetragonal ZrO 2 , which depended monotonically on the amount of ZrO 2 present before hot isostatic pressing, was increased by pressing but became almost constant between 5 and 15 wt% ZrO 2 addition. The strength appeared to be controlled by pores before pressing and by surface flaws after pressing; the size of flaws after pressing increased with ZrO 2 content. The strength of ZTA containing mostly monoclinic ZrO 2 (20 to 25 wt%) remained almost constant despite the noticeable density increase upon hot isostatic pressing because the strength was controlled by preexisting microcracks whose extent did not change on postsintering pressing. These strength-toughness relations in sintered and isostatically hot-pressed ZTA are explained on the basis of R-curve behavior. The importance of the contribution of microcracks to the toughness of ZTA is emphasized

Effect of Cu2+ ion incorporation on the phase development of ZrO2-type solid solutions during the thermal treatments

International Nuclear Information System (INIS)

Stefanic, Goran; Music, Svetozar; Ivanda, Mile

2010-01-01

The amorphous precursors of the ZrO 2 -CuO system at the ZrO 2 -rich side of the concentration range were prepared by co-precipitation from aqueous solutions of the corresponding salts. Thermal behavior of the amorphous precursors was monitored using X-ray powder diffraction, Raman spectroscopy, field emission scanning electron microscopy, energy dispersive X-ray spectrometry, differential scanning calorimetry and thermogravimetric analysis. The crystallization temperature of the amorphous precursors rose with an increase in the CuO content for ∼180 o C. Maximum solubility of Cu 2+ ions in the ZrO 2 lattice (∼23 mol%) occurs in the metastable products obtained upon crystallization of the amorphous precursors. The results of Raman spectroscopy indicate that the incorporation of Cu 2+ ions stabilize the tetragonal ZrO 2 polymorph. A precise determination of lattice parameters, using both Rietveld and Le Bail refinements of the powder diffraction patterns, showed that the axial ratio c/a in the ZrO 2 -type solid solutions with a Cu 2+ content ≥20 mol% approach 1 (formation of t''-form of tetragonal phase). The terminal solid solubility limit of Cu 2+ ions in the ZrO 2 lattice rapidly drops with an increase in treatment temperature (up to 1000 o C) that is followed by the formation of and increase in phases structurally closely related to tenorite and monoclinic ZrO 2 . Low thermal stability of the t-ZrO 2 -type phase was attributed to the reduction of the sintering temperature in the presence of CuO and a significant difference in size and shape of zirconia and tenorite particles, which prevent surface interactions.

Development and characterization of nickel catalysts supported in CeO2-ZrO2-Al2O3, CeO2-La2O3-Al2O3 e ZrO2-La2O3-Al2O3 matrixes evaluated for methane reforming reactions

International Nuclear Information System (INIS)

Abreu, Amanda Jordão de

2012-01-01

Nowadays, the methane reforming is large interest industrial for the take advantage of these gas in production the hydrogen and synthesis gas (syngas). Among in the reactions of methane stand of the reactions steam reforming and carbon dioxide reforming of methane. The main catalysts uses in the methane reforming is Ni/Al 2 O 3 . However, the supported-nickel catalyst is susceptible to the deactivation or the destruction by coke deposition. The carbon dissolves in the nickel crystallite and its diffuses through the nickel, leading for formation of the carbon whiskers, which results in fragmentation of the catalyst. Modification of such catalysts, like incorporation of suitable promoters, is desirable to achieve reduction of the methane hydrogenolysis and/or promotion of the carbon gasification. Catalysts 5%Ni/Al 2 O 3 supported on solid solutions formed by ZrO 2 -CeO 2 , La 2 O 3 and CeO 2 -ZrO 2 -La 2 O 3 were prepared, characterized and evaluated in reactions steam and carbon dioxide reforming and partial oxidation of methane with objective the value effect loading solution solid in support. The supports were prepared by co-precipitation method and catalysts were prepared by impregnation method and calcined at 500 deg C. The supports and catalysts were characterized by Nitrogen Adsorption, method -rays diffraction (XRD), X-rays dispersive spectroscopy (XDS), spectroscopy in the region of the ultraviolet and the visible (UV-vis NIR) to and temperature programmed reduction (TPR), Raman Spectroscopy, X-ray absorption spectroscopy and Thermogravimetric Analysis. After all the catalytic reactions check which the addition of solid solution is beneficial for Ni/Al 2 O 3 catalysts and the best catalysts are Ni/CeO 2 -La 2 O 3 -Al 2 O 3 . (author)

Thermally stimulated currents in ZrO2:MgO

International Nuclear Information System (INIS)

Muccillo, E.N.S.

1987-01-01

Thermally Stimulated Depolarization Current measurements between 100 K and 350 K have been performed in ZrO 2 :MgO ceramic samples to discriminate the several kinds of polarization (orientational and interfacial polarization, and extrinsic and intrinsic space charge effects) to allow for the use of the technique in the study of solid solution formation in partially stabilized zirconia. The samples were prepared by conventional ceramic processing methods. Different electrode materials have been used: colloidal graphite, silver, gold, and also insulating electrodes (e.g. mylar foils). The current spectra obtained are strongly dependent upon the electrode material showing the presence of spacial charge phenomenon in these ceramics. (Author) [pt

Thermally stimulated currents in ZrO2:MgO

International Nuclear Information System (INIS)

Muccillo, E.N.S.

1987-01-01

Thermally Stimulated Depolarization Current measurements between 100 K and 350 K have been performed in ZrO 2 :MgO ceramic samples to discriminate the several Kinds of polarization (orientational and interfacial polarization, and extrinsic and intrinsic space charge effects) to allow for the use of the technique in the study of solid solution formation in partially stabilized zirconia. The samples were prepared by conventional ceramic processing methods. Different electrode materials have been used: colloidal graphite, silver, gold, and also insulating electrodes (e.g. mylar foils). The current spectra obtained are strongly dependent upon the electrode material showing the presence of spacial charge phenomenon in these ceramics. (Author) [pt

Dynamic compaction of Al2O3-ZrO2 compositions

International Nuclear Information System (INIS)

Tunaboylu, B.; McKittrick, J.; Nutt, S.R.

1994-01-01

Shock compaction of Al 2 O 3 -ZrO 2 binary and ternary powder compositions resulted in dense, one-piece samples without visible cracks for pressures ≤12.6 GPa. Dynamic pressures were achieved by using a 6.5-m-long two-state gas gun. It is believed that plastic deformation by dislocation slip of α-Al 2 O 3 partially accommodates the tensile stresses created during the release of shock pressures. A fine and narrow particle size distribution is necessary to achieve high bulk densities, but the bulk structural integrity was not strongly related to the distribution. A high-pressure phase of ZrO 2 , which was formed from the monoclinic polymorph, was found at and above shock pressure of 6.3 GPa. No evidence of the orthorhombic cotunnite structure was observed. Compaction of glassy and submicrocrystalline rapidly solidified starting materials showed good structural integrity, although the bulk density was relatively low. It is not clear what the densification/bonding mechanism is in these materials, although it appears not to be plastic deformation. Microstructural analysis showed that fine and uniform microstructures are retained after compaction at appropriate dynamic pressures for all compositions, with some interparticle cohesion present

Thermal shock behavior of toughened gadolinium zirconate/YSZ double-ceramic-layered thermal barrier coating

International Nuclear Information System (INIS)

Zhong, Xinghua; Zhao, Huayu; Zhou, Xiaming; Liu, Chenguang; Wang, Liang; Shao, Fang; Yang, Kai; Tao, Shunyan; Ding, Chuanxian

2014-01-01

Highlights: • Gd 2 Zr 2 O 7 /YSZ DCL thermal barrier coating was designed and fabricated. • The Gd 2 Zr 2 O 7 top ceramic layer was toughened by addition of nanostructured 3YSZ. • Remarkable improvement in thermal shock resistance of the DCL coating was achieved. - Abstract: Double-ceramic-layered (DCL) thermal barrier coating system comprising of toughened Gadolinium zirconate (Gd 2 Zr 2 O 7 , GZ) as the top ceramic layer and 4.5 mol% Y 2 O 3 partially-stabilized ZrO 2 (4.5YSZ) as the bottom ceramic layer was fabricated by plasma spraying and thermal shock behavior of the DCL coating was investigated. The GZ top ceramic layer was toughened by addition of nanostructured 3 mol% Y 2 O 3 partially-stabilized ZrO 2 (3YSZ) to improve fracture toughness of the matrix. The thermal shock resistance of the DCL coating was enhanced significantly compared to that of single-ceramic-layered (SCL) GZ-3YSZ composite coating, which is believed to be primarily attributed to the two factors: (i) the increase in fracture toughness of the top ceramic layer by incorporating nanostructured YSZ particles and (ii) the improvement in strain tolerance through the utilization of 4.5YSZ as the bottom ceramic layer. In addition, the failure mechanisms are mainly attributed to the still low fracture toughness of the top ceramic layer and oxidation of the bond-coat

The effect of nano-size ZrO2 powder addition on the microstructure and superconducting properties of single-domain Y-Ba-Cu-O bulk superconductors

International Nuclear Information System (INIS)

Iida, K; Babu, N H; Reddy, E S; Shi, Y-H; Cardwell, D A

2005-01-01

The effect of nano-size ZrO 2 powder addition on the microstructure and superconducting properties of Y-Ba-Cu-O single grain bulk superconductors has been investigated. Significant pushing phenomena of Y 2 BaCuO 5 (Y-211) particles, particularly in the c growth sector, were observed even with a small amount of ZrO 2 added to the precursor powder. An increase in Y-211 particle pushing was observed with increasing ZrO 2 content, leading to an inhomogeneous bulk microstructure. In addition, a growth cycle consisting of a Y-211 free layer-porous narrow layer-Y-211 high concentration layer was observed for samples prepared with 0.25 wt% ZrO 2 in both the a and c growth sectors. The extent of the growth of single grain Y-Ba-Cu-O (YBCO) decreased with increasing ZrO 2 content due to increased pushing of Y-211 particles towards molten liquid. The superconducting transition temperature, T c , of the ZrO 2 containing YBCO samples was sharp but depressed slightly (by up to 1 K) compared with an undoped YBCO grain, indicating a relative insensitivity of T c to ZrO 2 content. Finally, the sensitivity of critical current density, J c , to applied magnetic field in large grain bulk YBCO containing ZrO 2 was observed to depend critically on position due to the inhomogeneous sample microstructure

Preparation and determination of the luminescent characteristics of ZrO2 in powder

International Nuclear Information System (INIS)

Rivera M, T.; Olvera T, L.; Azorin N, J.; Soto E, A.M.; Velazquez O, C.; Campero C, A.

2004-01-01

In this work the luminescent characteristics of the ZrO 2 are presented using the method of Thermally Stimulated Luminescence (TSL), also called thermoluminescence (Tl). The powders of ZrO 2 were obtained by two preparation methods: for precipitation and for evaporation of Sol-gel. The luminescent characteristics of the ZrO 2 are determined using a lamp of radiation of UV light and a radiation source of beta particles of 90 Sr/ 90 Y. Using the method of thermal stimulation the curve representative thermoluminescent of the previously irradiated material was obtained. The curve Tl of the ZrO 2 irradiated with UV light presents a maximum in 180 C. Likewise, the spectrum of the curve Tl of the ZrO 2 irradiated with particles beta presents a maximum centered in 181 C. While using gamma radiation like excitement source one has a spectrum with a peak centered in 184 C. When subjecting the materials obtained by sol-gel to a process of calcination at 1000 C for 24 hours a curved Tl it presents with two maxim in 185 and in 290 C respectively. The intensity of the response induced in the material it is a decisive factor to continue studying the dosimetric characteristics of the ZrO 2 what allows to consider it as a potential material to use it in the beta particle dosimetry and of the UV light using the thermoluminescence method (Tl). (Author)

Performance and stability of (ZrO2)0.89(Y2O3)0.01(Sc2O3)0.10-LaCr0.85Cu0.10Ni0.05O3-δ oxygen transport membranes under conditions relevant for oxy-fuel combustion

DEFF Research Database (Denmark)

Pirou, Stéven; Bermudez, Jose M.; Tak Na, Beom

2018-01-01

Self-standing, planar dual-phase oxygen transport membranes consisting of 70 vol.% (ZrO2)0.89(Y2O3)0.01(Sc2O3)0.10 (10Sc1YSZ) and 30 vol.% LaCr0.85Cu0.10Ni0.05O3-δ (LCCN) were successfully developed and tested. The stability of the composite membrane was studied in simulated oxy-fuel power plant...

Structural and chemical degradation mechanisms of pure YSZ and its components ZrO2 and Y2O3 in carbon-rich fuel gases.

Science.gov (United States)

Köck, Eva-Maria; Kogler, Michaela; Götsch, Thomas; Klötzer, Bernhard; Penner, Simon

2016-05-25

Structural and chemical degradation mechanisms of metal-free yttria stabilized zirconia (YSZ-8, 8 mol% Y2O3 in ZrO2) in comparison to its pure oxidic components ZrO2 and Y2O3 have been studied in carbon-rich fuel gases with respect to coking/graphitization and (oxy)carbide formation. By combining operando electrochemical impedance spectroscopy (EIS), operando Fourier-transform infrared (FT-IR) spectroscopy and X-ray photoelectron spectroscopy (XPS), the removal and suppression of CH4- and CO-induced carbon deposits and of those generated in more realistic fuel gas mixtures (syngas, mixtures of CH4 or CO with CO2 and H2O) was examined under SOFC-relevant conditions up to 1273 K and ambient pressures. Surface-near carbidization is a major problem already on the "isolated" (i.e. Nickel-free) cermet components, leading to irreversible changes of the conduction properties. Graphitic carbon deposition takes place already on the "isolated" oxides under sufficiently fuel-rich conditions, most pronounced in the pure gases CH4 and CO, but also significantly in fuel gas mixtures containing H2O and CO2. For YSZ, a comparative quantification of the total amount of deposited carbon in all gases and mixtures is provided and thus yields favorable and detrimental experimental approaches to suppress the carbon formation. In addition, the effectivity and reversibility of removal of the coke/graphite layers was comparably studied in the pure oxidants O2, CO2 and H2O and their effective contribution upon addition to the pure fuel gases CO and CH4 verified.

Study of the tribological properties of ZrO2 obtained by thermal spraying using the interferometric microscopy

International Nuclear Information System (INIS)

Guilemany, J. M.; Armada, S.; Miguel, J. M.

2001-01-01

Thermal barrier coatings have a limited mechanical and tribological properties. The sintering thermal treatments can be used to improve these properties. in the present paper the evolution of some mechanical and tribological properties with different time of sintering at 1000 degree centigree is evaluated. It was observed that the sintering thermal treatment produce an increase of the wear resistance, the hardness and the Young modulus. The Ball on disk test were done using a sliding pair of ZrO 2 and steel and the main wear mechanisms for each case were studied. It was observed that the intersplat delamination and the brittle fracture where the main wear mechanisms during sliding process. The wear tracks were studied with scanning electron microscopy (SEM) and scanning white light interferometry (SWLI) so as to quantify the wear for each case. It was necessary to do a gold sputtering to increase the electric conductivity and reflection of the ZrO 2 samples for their study by SEM and SWLI respectively. (Author) 6 refs

Effect of La2O3 addition on interface chemistry between 4YSZ top layer and Ni based alloy bond coat in thermal barrier coating by EB PVD.

Science.gov (United States)

Park, Chan-Young; Yang, Young-Hwan; Kim, Seong-Won; Lee, Sung-Min; Kim, Hyung-Tae; Jang, Byung-Koog; Lim, Dae-Soon; Oh, Yoon-Suk

2014-11-01

The effect of a 5 mol% La2O3 addition on the forming behavior and compositional variation at interface between a 4 mol% Yttria (Y2O3) stabilized ZrO2 (4YSZ) top coat and bond coat (NiCrAlY) as a thermal barrier coating (TBC) has been investigated. Top coats were deposited by electron beam physical vapor deposition (EB PVD) onto a super alloy (Ni-Cr-Co-Al) substrate without pre-oxidation of the bond coat. Top coats are found to consist of dense columnar grains with a thin interdiffusion layer between metallic bond coats. In the as-received 4YSZ coating, a thin interdiffusion zone at the interface between the top and bond coats was found to consist of a Ni-Zr intermetallic compound with a reduced quantity of Y, Al or O elements. On the other hand, in the case of an interdiffusion area of 5 mol% La2O3-added 4YSZ coating, it was found that the complicated composition and structure with La-added YSZ and Ni-Al rich compounds separately. The thermal conductivity of 5 mol% La2O3-added 4YSZ coating (- 1.6 W/m x k at 1100 degrees C) was lower than a 4YSZ coating (- 3.2 W/m x k at 1100 degrees C) alone.

Thermal cycling behavior of La{sub 2}Zr{sub 2}O{sub 7} coating with the addition of Y{sub 2}O{sub 3} by EB-PVD

Energy Technology Data Exchange (ETDEWEB)

Xu Zhenhua [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Graduate School of Chinese Academy of Sciences, Beijing 100039 (China); Beijing Institute of Aeronautical Materials, Department 5, P.O. Box 81-5, Beijing 100095 (China); He Limin, E-mail: he_limin@yahoo.co [Beijing Institute of Aeronautical Materials, Department 5, P.O. Box 81-5, Beijing 100095 (China); Chen Xiaolong; Zhao Yu [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Mu Rende; He Shimei [Beijing Institute of Aeronautical Materials, Department 5, P.O. Box 81-5, Beijing 100095 (China); Cao Xueqiang, E-mail: xcao@ciac.jl.c [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2010-10-15

Thermal barrier coatings (TBCs) of La{sub 2}Zr{sub 2}O{sub 7} (LZ) with the addition of 3 wt.% Y{sub 2}O{sub 3} (LZ3Y) were deposited by electron beam-physical vapor deposition (EB-PVD). The phase structures, surface and cross-sectional morphologies, cyclic oxidation behaviors of these coatings were studied in detail. The thermal cycling test at 1373 K in an air furnace indicates that the LZ3Y coating has a lifetime of 617 cycles which is about 10% longer than that of LZ coating. The improvement of chemical homogeneity of the coating, the superior growth behavior of columns and the favorable mechanical properties are all very helpful to the prolongation of thermal cycling life of LZ3Y coating. The failure of LZ and LZ3Y coatings is mainly a result of the excess La{sub 2}O{sub 3}, the chemical incompatibility of ceramic coatings with TGO layer, the thermal expansion mismatch between ceramic coatings and bond coat, and the outward diffusion of alloying elements into the ceramic coatings.

Highly Stable Sr-Free Cobaltite-Based Perovskite Cathodes Directly Assembled on a Barrier-Layer-Free Y2 O3 -ZrO2 Electrolyte of Solid Oxide Fuel Cells.

Science.gov (United States)

Ai, Na; Li, Na; Rickard, William D A; Cheng, Yi; Chen, Kongfa; Jiang, San Ping

2017-03-09

Direct assembly is a newly developed technique in which a cobaltite-based perovskite (CBP) cathode can be directly applied to a barrier-layer-free Y 2 O 3 -ZrO 2 (YSZ) electrolyte with no high-temperature pre-sintering steps. Solid oxide fuel cells (SOFCs) based on directly assembled CBPs such as La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ show high performance initially but degrade rapidly under SOFC operation conditions at 750 °C owing to Sr segregation and accumulation at the electrode/electrolyte interface. Herein, the performance and interface of Sr-free CBPs such as LaCoO 3-δ (LC) and Sm 0.95 CoO 3-δ (SmC) and their composite cathodes directly assembled on YSZ electrolyte was studied systematically. The LC electrode underwent performance degradation, most likely owing to cation demixing and accumulation of La on the YSZ electrolyte under polarization at 500 mA cm -2 and 750 °C. However, the performance and stability of LC electrodes could be substantially enhanced by the formation of LC-gadolinium-doped ceria (GDC) composite cathodes. Replacement of La by Sm increased the cell stability, and doping of 5 % Pd to form Sm 0.95 Co 0.95 Pd 0.05 O 3-δ (SmCPd) significantly improved the electrode activity. An anode-supported YSZ-electrolyte cell with a directly assembled SmCPd-GDC composite electrode exhibited a peak power density of 1.4 W cm -2 at 750 °C, and an excellent stability at 750 °C for over 240 h. The higher stability of SmC as compared to that of LC is most likely a result of the lower reactivity of SmC with YSZ. This study demonstrates the new opportunities in the design and development of intermediate-temperature SOFCs based on the directly assembled high-performance and durable Sr-free CBP cathodes. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Pair Distribution Function Analysis of ZrO2 Nanocrystals and Insights in the Formation of ZrO2-YBa2Cu3O7 Nanocomposites

Directory of Open Access Journals (Sweden)

Hannes Rijckaert

2018-06-01

Full Text Available The formation of superconducting nanocomposites from preformed nanocrystals is still not well understood. Here, we examine the case of ZrO2 nanocrystals in a YBa2Cu3O7−x matrix. First we analyzed the preformed ZrO2 nanocrystals via atomic pair distribution function analysis and found that the nanocrystals have a distorted tetragonal crystal structure. Second, we investigated the influence of various surface ligands attached to the ZrO2 nanocrystals on the distribution of metal ions in the pyrolyzed matrix via secondary ion mass spectroscopy technique. The choice of stabilizing ligand is crucial in order to obtain good superconducting nanocomposite films with vortex pinning. Short, carboxylate based ligands lead to poor superconducting properties due to the inhomogeneity of metal content in the pyrolyzed matrix. Counter-intuitively, a phosphonate ligand with long chains does not disturb the growth of YBa2Cu3O7−x. Even more surprisingly, bisphosphonate polymeric ligands provide good colloidal stability in solution but do not prevent coagulation in the final film, resulting in poor pinning. These results thus shed light on the various stages of the superconducting nanocomposite formation.

Crystallization and sintering characteristics of CaO-Al2O3-SiO2 glasses in the presence of TiO2, CaF2 and ZrO2

International Nuclear Information System (INIS)

Banijamali, S.; Eftekhari Yekta, B.; Rezaie, H.R.; Marghussian, V.K.

2009-01-01

In this study, the effects of different amounts of TiO 2 , ZrO 2 and CaF 2 nucleating agents on sinterability, crystallization, mechanical properties and chemical resistance of glass-ceramics belonging to the CaO-Al 2 O 3 -SiO 2 system were investigated, using differential thermal analysis (DTA), X-ray diffractometry (XRD), scanning electron microscopy (SEM), mechanical and chemical resistance measurements. It was found that in CaF 2 containing samples, the sinterability, crystallization and mechanical properties were improved by increasing of CaF 2 amount. However, addition of ZrO 2 and TiO 2 increases the firing temperature required for complete densification of specimens. Our experiments showed that fluctuations of chemical composition of the residual glass phases during sintering were responsible for these dissimilar trends and greatly influenced mechanical and chemical properties. According to the obtained results, appropriate sinterability, acceptable mechanical and chemical properties, as well as desirable whiteness of the most promising specimens make them suitable choices for floor tile applications. The main crystallization phases in all fully sintered glass-ceramics were wollastonite, anorthite and calcium aluminum silicate.

Glass forming in La2O3-TiO2-ZrO2 ternary system by containerless processing

Science.gov (United States)

Kaneko, Masashi; Kentei Yu, Yu; Kumar, Vijaya; Masuno, Atsunobu; Inoue, Hiroyuki; Odawara, Osamu; Yoda, Shinichi

The containerless processing is an appropriate method to create new glasses, because it sup-presses nucleation at the boundary between liquid and crucible during solidification and it enables molten samples to be solidified without crystallization. Recently, we have succeeded in forming BaTi2 O5 glass in the bulk state by using an aerodynamic levitation furnace. BaTi2 O5 glass includes no traditional glass network former and it possesses high electric permittivity [1, 2]. From the point of view of optical application, BaTi2 O5 glass has high refractive indices over 2.1. BaTi2 O5 glass, however, vitrify only in a small sphere, and it crystallize when its diameter exceed 1.5 mm. In order to synthesize new titanate oxide glasses which possess higher refractive indices and larger diameter than BaTi2 O5 , La and Zr can be used as substitutive components. When Ba is replaced with La, refractive indices are expected to increase because of the heavier element. The addition of a third element is thought to be effective for enhance-ment of glass formation ability and Zr can be a candidate because Ti and Zr are homologous. In this research, we have succeeded in forming new bulk glass in La2 O3 -TiO2 -ZrO2 ternary system by means of the aerodynamic levitation furnace. We investigated the glass forming region, thermal properties and optical properties of La2 O3 -TiO2 -ZrO2 glass. Glass transition temperature, crystallization temperature, density, refractive indices and transmittance spectra were varied depending on the chemical composition. Reference [1] J. Yu et al, "Fabrication of BaTi2O5 Glass-Ceramics with Unusual Dielectric Properties during Crystallization", Chem-istry of Materials, 18 (2006) 2169-2173. [2] J. Yu et al., "Comprehensive Structural Study of Glassy and Metastable Crystalline BaTi2O5", Chemistry of Materials, 21 (2009) 259-263.

Effect of cooling rate on tetragonal to monoclinic transformation in hot pressed ZrO2(Y2O3) ceramics

International Nuclear Information System (INIS)

Zhu, W.Z.; Ding, Z.S.; Lei, T.C.; Zhou, Y.

1995-01-01

It is well documented that the tetragonal (T) to monoclinic (M) transition in either pure zirconia or partially stabilized zirconia is the origin of toughening in that resistance to the propagation of cracks can be greatly enhanced by the concurrent appearance of the stress field of the transformation. In the present paper, the effect of cooling rate on the T → M phase transformation in yttria-containing zirconia and its resultant mechanical properties have been studied by means of thermal expansion analysis. Both the T → M and M → T transformations are affected by the cooling and heating rates, respectively. The amount of M-phase decreases with increasing cooling rate. T → M transition occurring within the interior part of specimen can be completely inhibited by the cooling rate of 100 C/min for ZrO 2 (2mol% Y 2 O 3 ) ceramic sintered at 1,600 C. The start point and end point of the T → M transformation decreases and increases, respectively, with increasing cooling rate. Both the start point and end point of the M → T transformation increase with increasing cooling rate. The divergence between the results of X-ray diffraction and the thermal expansion analysis has been rationalized in terms of the both internal and external factors, namely, preferential sites of surface for the formation of the M-phase and limited sensitivity of measurement of the thermal expansion apparatus. Both the water-cooled and air-cooled specimens show much improved mechanical properties regardless of the sintering temperatures or yttria content because of the relatively higher T-phase fraction retained to room temperature

Porosity and biocompatibility study of ceramic implants based on ZrO2 and Al2O3

International Nuclear Information System (INIS)

Litvinova, Larisa; Shupletsova, Valeria; Leitsin, Vladimir; Vasyliev, Roman; Zubov, Dmitry; Buyakov, Ales; Kulkov, Sergey

2014-01-01

The work studies ZrO 2 (Me x O y )-based porous ceramics produced from the powders consisting of hollow spherical particles. It was shown that the structure is represented by a cellular framework with bimodal porosity consisting of sphere-like large pores and pores that were not filled with the powder particles during the compaction. For such ceramics, the increase of pore volume is accompanied by the increased strain in an elastic area. It was also shown that the porous ZrO 2 ceramics had no acute or chronic cytotoxicity. At the same time, ceramics possess the following osteoconductive properties: adhesion support, spreading, proliferation and osteogenic differentiation of MSCs

Toughening of dental porcelain by tetragonal ZrO2 additions

International Nuclear Information System (INIS)

Morena, R.; Lockwood, P.E.; Evans, A.L.; Fairhurst, C.W.

1986-01-01

The effect of mechanical behavior of ZrO 2 additions to a dental porcelain was investigated. The ZrO 2 was introduced into the glassy matrix phase of the porcelain by refritting the all-glass porcelain constituent. X-ray diffraction indicated that a sizeable fraction of the ZrO 2 was retained in the tetragonal from after the porcelain was fired. Zirconia additions to the porcelain produced substantial improvements in fracture toughness, strength, and thermal shock resistance

Wear and related evaluations of partially stabilized ZrO2

International Nuclear Information System (INIS)

Rice, R.W.; Wu, C.C.

1985-01-01

Pin-On-Disk (POD) tests show partially stabilized ZrO 2 (PSZ) crystals to have about the same wear as fully stabilized ZrO 2 crystals unit stabilizer contents are low enough (e.g., 4-5 wt % Y 2 O 3 ) so that some monoclinc ZrO 2 is present. Then wear increases substantially as stabilizer content is further reduced, and monoclinic content increases. Tests of PSZ-crystal cutting tools have not proved particularly successful, and rolling-contact fatigue tests of various PSZ materials showed them to be poor candidates for rolling-element bearings, with the later results indicating a petch-type dependence. Possible reasons for such limited or poor performance of PSZ, despite its good toughness, are discussed. Poor performance with concentrated loads is noted in particular, indicating limitations due to plastic flow

Pure and Y-substituted BaZrO3 ceramics. A possible support material for fabrication of YBa2Cu3O7-x high-Tc superconductors

International Nuclear Information System (INIS)

Wang Xiandong.

1993-01-01

This thesis concerns the preparation and characterization of cuprate based high-T c superconductors (Y-123 and Bi-2223) and especially development and testing of BaZrO 3 based materials. The formation of YBa 2 Cu 3 O y (Y-123) by a CO 2 -free route involving reaction sintering of stoichiometric mixtures of chemically prepared fine powders of Y 2 BaCuO 5 , BaCuO 2 and CuO have been studied by thermal and XRD analysis. The synthesis and sintering of BaZrO 3 powders prepared by the hydroxide-alkoxide-methanol sol-gel route have been studied. The phase relations in the system BaO-Y 2 O 3 -ZrO 2 have been studied to determine the solid solubility limits for the perovskite phase Ba X Y Y Zr Z O N (X+X+Z=3) at 1500 deg. C. In the binary system Y 2 O 3 -BaZrO 3 the solubility limit was found to be ≅19 mol% Y 2 O 3 , i.e. Ba 0.81 Y 0. 4 2 Zr 0.81 O 3 . along the joint BaYO 2.5 -Ba the boundary was determined to be at BaY 0.21 Zr 0 . 79 O 2.895 . evidence for a new solid solution series between Ba 3 Y 4 O 9 and ZrO 2 are given, and a partial 1500 deg. C phase diagram for the ternary system BaO-Y 2 O 3 -ZrO 2 is presented. The growth of BaZrO 3 single crystals have been attempted both by a laser zone floating technique and flux methods. The compatibility between YBa 2 Cu 3 O 7 -X and BaZrO 3 , Ba X Y Y Zr Z O 3-δ as well as BaHfO 3 have been studied at 950 deg. and 1050 deg. C. The results show the four most promising candidates as support materials for fabrication of YBa 2 Cu 3 O y to be BaHfO 3 , BaY 0.05 Zr 0.95 O 2.975 , , BaZrO 3 and BaY 0.1 Zr 0.9 O 2.95 . (EG)

Óxidos Mistos de Al2O3/ZrO2 como Inibidores de Corrosão do Aço SAE 1020

Directory of Open Access Journals (Sweden)

Marcelo Rodrigues da Silva

2014-01-01

Full Text Available This paper describes the use of Al2O3/ZrO2 mixed oxides synthesized by sol-gel process with different amounts of ZrO2 (5%, 10%, 15% and 20% by mass in the Al2O3 matrix and different temperatures of calcination, such as interesting inhibitor materials of corrosive processes of SAE 1020 steel. The materials were characterized by Infrared Spectroscopy Fourier Transform (FTIR and X-Ray Diffraction (XRD techniques. FTIR spectra show the typical Al-O and Zr-O bonds vibrations in the mixed oxides. The XRD patterns of the samples calcined at 800 °C and 1000 °C shows the ZrO2 tetragonal and γ-Al2O3 face-centered cubic (FCC phases. The corrosion tests showed that the SAE 1020 steel covered with mixed oxides have an anodic passive region, thereby inhibiting the corrosive processes on the metal surface. Furthermore, the found values for steel coated with mixed oxide synthesized indicate a decrease in corrosion potentials (Ecor and corrosion current (icor. With respect to different samples of mixed oxides, the sample with 20 % of ZrO2 in the Al2O3 matrix proved to be the best inhibitor of steel corrosion, with the lowest values of corrosion potential and corrosion current, - 1.32 V and 0.31 μA cm-2, respectively.

Investigation of the growth of In2O3 on Y-stabilized ZrO2(100) by oxygen plasma assisted molecular beam epitaxy

International Nuclear Information System (INIS)

Bourlange, A.; Payne, D.J.; Palgrave, R.G.; Foord, J.S.; Egdell, R.G.; Jacobs, R.M.J.; Schertel, A.; Hutchison, J.L.; Dobson, P.J.

2009-01-01

Thin films of In 2 O 3 have been grown on Y-stabilised ZrO 2 (100) substrates by oxygen plasma assisted molecular beam epitaxy over a range of substrate temperatures between 650 o C and 900 o C. Growth at 650 o C leads to continuous but granular films and complete extinction of substrate core level structure in X-ray photoelectron spectroscopy. However with increasing substrate temperature the films break up into a series of discrete micrometer sized islands. Both the continuous and the island films have excellent epitaxial relationship with the substrate as gauged by X-ray diffraction and selected area electron diffraction and lattice imaging in high resolution transmission electron microscopy.

Effect of ion nitriding on the crystal structure of 3 mol% Y2O3-doped ZrO2 thin-films prepared by the sol-gel method

International Nuclear Information System (INIS)

Ortiz, A.L.; Diaz-Parralejo, A.; Borrero-Lopez, O.; Guiberteau, F.

2006-01-01

We investigated the effect of ion nitriding on the crystal structure of 3 mol% Y 2 O 3 -doped ZrO 2 (3YSZ) thin-films prepared by the sol-gel method. For this purpose, we used X-ray diffractometry to determine the crystalline phases, the lattice parameters, the crystal sizes, and the lattice microstrains, and glow discharge-optical emission spectroscopy to obtain the depth profiles of the elemental chemical composition. We found that nitrogen atoms substitute oxygen atoms in the 3YSZ crystal, thus leading to the formation of unsaturated-substitutional solid solutions with reduced lattice parameters and Zr 0.94 Y 0.06 O 1.72 N 0.17 stoichiometric formula. We also found that ion nitriding does not affect the grain size, but does generate lattice microstrains due to the increase in point defects in the crystalline lattice

The influence of Fe2O3 in the humidity sensor performance of ZrO2:TiO2-based porous ceramics

International Nuclear Information System (INIS)

Cosentino, I.C.; Muccillo, E.N.S.; Muccillo, R.

2007-01-01

ZrO 2 :TiO 2 ceramics were prepared with different porosity values by two methods: (a) sintering at 1150, 1300 and 1500 deg. C, corresponding to the temperatures of the first, second and third sintering stages, according to dilatometry results; (b) adding Fe 2 O 3 (2.0 and 5.0 mol%) to ZrO 2 :TiO 2 powders before sintering. The ZrO 2 :TiO 2 specimens were characterized by X-ray diffraction, mercury porosimetry, scanning electron microscopy and impedance spectroscopy. The impedance spectroscopy analysis was carried out under different relative humidities. The bulk electrical resistivity in the low frequency region (10-100 Hz) decreases for increasing relative humidity. Increasing the sintering temperature from the first to the third sintering stage promoted grain growth, as expected, with consequent decrease of the intergranular porosity. The use of Fe 2 O 3 as sintering aid reduced the porosity of the specimens, but increased the electrical response under humid environments in comparison with specimens sintered without Fe 2 O 3

CeO2-ZrO2 ceramic compounds

International Nuclear Information System (INIS)

Melo, F.C.L.; Cairo, C.A.C.; Devezas, T.C.; Nono, M.C.A.

1988-01-01

In order to study the mechanical properties of tetragonal polycrystal zirconia stabilized with ceria various powder compositions with different CeO 2 content were made. Modulus of rupture for those compounds was measured. Tetragonal retained phase was determined for samples of CeO 2 -ZrO 2 ceramics with and without superficial mechanical treatment. The experimental results allowed us to evaluate the effects of CeO 2 content and sintering temperature in the mechanical properties and tetragonal transformed phase (t→ m) in ceramics of CeO 2 -ZrO 2 systems. (author) [pt

Fracture toughness of MgCr2O4-ZrO2 composities

International Nuclear Information System (INIS)

Singh, J.P.

1985-01-01

The effect of unstabilized ZrO 2 inclusions on the fracture surface energy of MgCr 2 O 4 was studied as a function of ZrO 2 content. It was observed that fracture surface energy increases with increasing ZrO 2 content, and reaches the maximum value of 24.5 j/m 2 at 16.5 vol% ZrO 2 . This represents an approx. = fourhold increase in the fracture surface energy of Mg 2 O 4 as a result of ZrO 2 inclusions. It is proposed that this improvement results from the energy absorbed by the microcracks formed in the MgCr 2 O 4 matrix as a result of the tetragonal → monoclinic phase transormation of ZrO 2 and the associated volume expansion

Degradación de recubrimientos ZrO2-CaO/NiAlMo por oxidación isoterma

Directory of Open Access Journals (Sweden)

Utrilla, V.

2006-12-01

Full Text Available This paper analyses the degradation of a ceramic top coating 70%ZrO2 – 30%CaO deposited onto a stainless steel AISI 304 by thermal spray, using Ni-6%Al-5%Mo as overlay coating. These thermal barrier coatings were heat treated for 48, 120 and 288 h at 800 ºC to evaluate the degradation of these materials by isothermal oxidation. The microstructure evolution during oxidation was analysed by environmental scanning electron microscopy, transmission electron microscopy, X ray microanalysis and X ray diffraction. A thermally grown oxide layer was observed between the overlay coating and the ceramic top coating after oxidation. This layer was formed by a mixed Al and Ni oxides.En este trabajo se estudia la degradación de un recubrimiento 70%ZrO2 – 30%CaO crecido por proyección térmica de oxiacetileno sobre un acero inoxidable austenítico AISI 304 y empleando una leación de Ni-6%Al-5%Mo como capa de anclaje. Los recubrimientos se trataron térmicamente en aire a 800 ºC durante 48, 120 y 288 horas para evaluar la degradación de estos materiales por oxidación isotérmica. La evolución de la microestructura de las barreras como consecuencia del proceso de oxidación se analizó mediante microscopía electrónica de barrido ambiental, microscopía electrónica de transmisión, microanálisis de rayos X (EDX y difracción de rayos X. Durante la oxidación de los recubrimientos creció una capa intermedia de óxidos (“thermally grown oxides”, TGO entre el anclaje metálico y el recubrimiento cerámico formada por una mezcla de óxidos de Al y Ni.

Dynamic grain growth in superplastic Y-TZP and Al2O3/YTZ

International Nuclear Information System (INIS)

Nieh, T.G.; Tomasello, C.M.; Wadsworth, J.

1990-01-01

This paper reports that both static and dynamic grain growth have been studied during superplastic deformation of fine-grained yttria-stabilized tetragonal zirconia (Y-TZP) and alumina reinforced yttria-stabilized tetragonal zirconia (Al 2 O 3 /YTZ). Grain growth was observed in both materials at temperatures above 1350 degrees C. In the case of Y-TZP, both static and dynamic grain growth were found to obey a similar equation of the form: D 3 -D 0 3 = kt where D is the instantaneous grain size, D 0 is the initial grain size, t is the time, and k is a kinetic constant which depends primarily on temperature and grain boundary energy. The activation energies for Y-TZP were approximately 580 and 520 kJ/mol, for static and dynamic grain growth, respectively. In the case of Al 2 O 3 /YTZ, it was found that the grain growth rate for the Al 2 O 3 phase was slower than that for the ZrO 2 phase. The growth rate of the ZrO 2 phase in Al 2 O 3 /YTZ is, however, similar to that in monolithic ZrO 2 i.e., Y-TZP

NIR to visible frequency upconversion in Er3+ and Yb3+ codoped ZrO2 phosphor

International Nuclear Information System (INIS)

Singh, Vijay; Kim, Sang Hwan; Rai, Vineet Kumar; Al-Shamery, Katharina; Haase, Markus

2013-01-01

The ZrO 2 :Er 3+ codoped with Yb 3+ phosphor powders have been prepared by the urea combustion route. Formation of the compounds ZrO 2 :Er 3+ and ZrO 2 :Er 3+ , Yb 3+ was confirmed by XRD. The frequency upconversion emissions in the green and red regions upon excitation with a CW diode laser at ∝978 nm are reported. Codoping with Yb 3+ enhances the emission intensities of the triply ionized erbium in the green and red spectral regions by about ∝130 and ∝820 times respectively. The emission properties of the ZrO 2 :Er 3+ phosphor powders are discussed on the basis of excited state absorption, energy transfer, and cross-relaxation energy transfer mechanisms. (orig.)

ZrO2 coatings on stainless steel by aerosol thermal spraying

International Nuclear Information System (INIS)

Di Giampaolo, A.R.; Reveron, H.; Ruiz, H.; Poirier, T.; Lira, J.

1998-01-01

Zirconia coatings, with a wide range of thickness (1 to 80 μ) have been obtained by spraying a ZrO 2 sol with an oxyacetylenic flame, on stainless steel substrates. The sol was prepared by mixing Zr-n-propoxide and acetic acid in order to obtain a zirconium oxyacetate precipitate, which was filtrated, washed with 1-propanol, dryed and subjected to an hydrothermal treatment. A new sol-gel based ceramic deposition process , aerosol thermal spraying was developed based on previous thermal spray work. A compressed air spray gun was used to produce a fine aerosol flow which was injected in the flame of the thermal spray torch and deposited on polished and sand blasted substrates. This original technique allows simultaneous spraying, drying and partial sintering of the zirconia nanometric particles. The maximum working temperature necessary to yield a resistant coating is 1000 deg C. This method produced crack-free homogeneous layers of monoclinic ZrO 2 with good adhesion to the substrate and low porosity, as shown by X-ray diffraction and scanning electron microscopy. Oxidation test, carried out by heat treatments in air atmosphere at 800 deg C indicated good protection, mainly for low thickness coatings deposited in polished substrates. This original deposition technique offers several advantages when compared with classical thermal spraying techniques, such as plasma spraying. Copyright (1998) AD-TECH - International Foundation for the Advancement of Technology Ltd

Optical properties of ZrO2, SiO2 and TiO2-SiO2 xerogels and coatings doped with Eu3+ and Eu2+

Directory of Open Access Journals (Sweden)

Gonçalves Rogéria R.

1999-01-01

Full Text Available Eu3+ doped bulk monoliths and thin films were obtained by sol-gel methods in the ZrO2, SiO2 and SiO2-TiO2 systems. Eu3+ 5D0 ® 7FJ emission and decay time characteristics were measured during the entire experimental preparation route from the initial sol to the final xerogels. The crystalline phases identified were tetragonal ZrO2 and mixtures of rutile and anatase TiO2 at high temperature treatments in bulk samples. Good quality thin films were obtained for all systems by dip-coating optical glasses (Schott BK270. The same spectroscopic features were observed either for the bulk monoliths or the films. By appropriate heat treatments under H2 atmosphere Eu2+ containing samples could be obtained in the SiO2-TiO2 system.

Characterization of Pt catalysts supported in TiO2 and ZrO2 stabilized with La2O3 for the nitric oxide elimination

International Nuclear Information System (INIS)

Perez H, R.; Arenas, J.; Rodriguez, V.; Aguilar, A.; Gomez C, A.; Diaz, G.

2000-01-01

Simple oxides TiO 2 , ZrO 2 , La 2 O 3 and mixed TiO 2 -La 2 O 3 , ZrO 2 -La 2 O 3 at 10% mol of lanthane were prepared by the precipitation technique. The incorporation of Pt to the supports was by the classical impregnation method. It was characterized the catalytic materials by diverse techniques for determining the lost weight by thermogravimetric analysis (TGA), superficial area (BET), crystallinity of catalytic supports (DR-X) total acidity and for the catalytic activity was realized in the reaction model NO + CH 4 . (Author)

Metallo–organic compound-based plasma enhanced CVD of ZrO2 ...

Indian Academy of Sciences (India)

Unknown

require a passivation barrier (oxynitride or nitride) to prevent interfacial layer growth (Ngai et al 2000). Zirconium dioxide (ZrO2) is one of the few high-k dielectrics predicted to be thermodynamically stable in contact with silicon (Qi et al 1999). ZrO2 was also characterized for low electrical conductivity and chemical inertness ...

Microstructure and durability of zirconia thermal barrier coatings

International Nuclear Information System (INIS)

Suhr, D.S.; Mitchell, T.E.; Keller, R.J.

1983-01-01

Various combinations of plasma-sprayed bond coatings and zirconia ceramic coatings on a nickel-based superalloy substrate were tested by static thermal exposure at 1200 0 C and cyclic thermal exposure to 1000 0 C. The bond coats were based on Ni-Cr-Al alloys with additions of rare earth elements and Si. The ceramic coats were various ZrO 2 -Y 2 O 3 compositions, of which the optimum was found to be ZrO 2 -8.9 wt% Y 2 O 3 . Microstructural analysis showed that resistance to cracking during thermal exposure is strongly related to deleterious phase changes

Characterization of physical properties of Al2O3 and ZrO2 nanofluids for heat transfer applications

International Nuclear Information System (INIS)

Rocha, Marcelo S.; Cabral, Eduardo L.L.; Sabundjian, Gaiane; Yoriyaz, Helio; Lima, Ana Cecilia S.; Belchior Junior, Antonio; Prado, Adelk C.; Filho, Tufic M.; Andrade, Delvonei A.; Shorto, Julian M.B.; Mesquita, Roberto N.; Otubo, Larissa; Baptista Filho, Benedito D.; Pinho, Priscila G.M.; Ribatsky, Gherhardt; Moraes, Anderson Antonio Ubices

2015-01-01

Studies demonstrate that nanofluids based on metal oxide nanoparticles have physical properties that characterize them as promising fluids, mainly, in industrial systems in which high heat flux takes place. Water based nanofluids of Al 2 O 3 and ZrO 2 were characterized regarding its promising use in heat transfer applications. Three different concentrations of dispersed solutions of cited nanofluids were prepared (0.01% vol., 0.05% vol., and 0.1% vol.) from commercial nanofluids. Experimental measurements were carried out at different temperatures. Thermal conductivity, viscosity and density of the prepared nanofluids were measured. (author)

Evaluating the toughness of APS and HVOF-sprayed Al2O3-ZrO2-coatings by in-situ- and macroscopic bending

Czech Academy of Sciences Publication Activity Database

Kiilakoski, J.; Mušálek, Radek; Lukáč, František; Koivuluoto, H.; Vuoristo, P.

2018-01-01

Roč. 38, č. 4 (2018), s. 1908-1918 ISSN 0955-2219 R&D Projects: GA ČR GB14-36566G Institutional support: RVO:61389021 Keywords : Thermal spray * Al2O3-ZrO2 * Toughening * Fracture * Mechanical testing Subject RIV: JK - Corrosion ; Surface Treatment of Materials OBOR OECD: Coating and films Impact factor: 3.411, year: 2016 https://www.sciencedirect.com/science/article/pii/S0955221917308051

The preparation and role of Li_2ZrO_3 surface coating LiNi_0_._5Co_0_._2Mn_0_._3O_2 as cathode for lithium-ion batteries

International Nuclear Information System (INIS)

Xu, Yue; Liu, Yang; Lu, Zhongpei; Wang, Haiying; Sun, Deqin; Yang, Gang

2016-01-01

Graphical abstract: LiNi_0_._5Co_0_._2Mn_0_._3O_2 is coated by Li_2ZrO_3 layer with the thickness about 20 nm. Li_2ZrO_3 coating effectively improves cycling performance and rate capability. LZO-LMO delivers 194 mAh g"−"1 at 0.2 C and presents improved cyclic performance at 55 °C. - Highlights: • LiNi_0_._5Co_0_._2Mn_0_._3O_2 is coated by Li_2ZrO_3 layer with the thickness about 20 nm. • Li_2ZrO_3 coating effectively improves cycling performance and rate capability. • LZO-LMO delivers 194 mAh g"−"1 at 0.2 C and presents improved cyclic performance at 55 °C. • Li_2ZrO_3 coating suppresses cation dissolution and enhances the structural stability. - Abstract: Li_2ZrO_3-coated LiNi_0_._5Co_0_._2Mn_0_._3O_2 (LZO-LMO) is successful synthesized by using a wet chemical method. Li_2ZrO_3 coating formed a uniform layer on LiNi_0_._5Co_0_._2Mn_0_._3O_2 particles (LMO) without changing the crystal structure. Cyclic voltammetry (CV) and charge–discharge tests show that the Li_2ZrO_3-modified layer can improve the cyclic and rate performance. In the cut-off voltage of 2.7–4.6 V, LZO-LMO maintains 86% of the initial capacity at the 50th cycle, which is much higher than LMO with the retention of 66% of the initial capacity. The coating layer of LZO plays the positive role in conductivity of lithium diffusion and improves rate performance of LMO. At 10 C rates, LZO-LMO delivers the initial capacity of 95 mAh g"−"1 which is much higher than 40 mAh g"−"1 delivered by LMO. At the environmental temperature of 55 °C, LZO-LMO delivers the initial capacity of 194 mAh g"−"1 at 0.2 C rate and presents an improved cyclic performance in comparison with LMO. The elemental analysis of electrodes carried out after 50 charge/discharge cycles shows minor Ni content deviation in LMO, but LZO-LMO still remains the stoichiometric ratio, because the Li_2ZrO_3 coating efficiently hinders the metal dissolution during charge/discharge.

Enhanced Photocatalytic Activity of ZrO2-SiO2 Nanoparticles by Platinum Doping

Directory of Open Access Journals (Sweden)

Mohammad W. Kadi

2013-01-01

Full Text Available ZrO2-SiO2 mixed oxides were prepared via the sol-gel method. Photo-assisted deposition was utilized for doping the prepared mixed oxide with 0.1, 0.2, 0.3, and 0.4 wt% of Pt. XRD spectra showed that doping did not result in the incorporation of Pt within the crystal structure of the material. UV-reflectance spectrometry showed that the band gap of ZrO2-SiO2 decreased from 3.04 eV to 2.48 eV with 0.4 wt% Pt doping. The results show a specific surface area increase of 20%. Enhanced photocatalysis of Pt/ZrO2-SiO2 was successfully tested on photo degradation of cyanide under illumination of visible light. 100% conversion was achieved within 20 min with 0.3 wt% of Pt doped ZrO2-SiO2.

Influence of Y2O3 Addition on Crystallization, Thermal, Mechanical, and Electrical Properties of BaO-Al2O3-B2O3-SiO2 Glass-Ceramic for Ceramic Ball Grid Array Package

Science.gov (United States)

Li, Bo; Li, Wei; Zheng, Jingguo

2018-01-01

Y2O3 addition has a significant influence on the crystallization, thermal, mechanical, and electrical properties of BaO -Al2O3 -B2O3 -SiO2 (BABS) glass-ceramics. Semi-quantitative calculation based on x-ray diffraction demonstrated that with increasing Y2O3 content, both the crystallinity and the phase content of cristobalite gradually decreased. It is effective for the additive Y2O3 to inhibit the formation of cristobalite phase with a large coefficient of thermal expansion value. The flexural strength and the Young's modulus, thus, are remarkably increased from 140 MPa to 200 MPa and 56.5 GPa to 63.7 GPa, respectively. Also, the sintering kinetics of BABS glass-ceramics with various Y2O3 were investigated using the isothermal sintering shrinkage curve at different sintering temperatures. The sintering activation energy Q sharply decreased from 99.8 kJ/mol to 81.5 kJ/mol when 0.2% Y2O3 was added, which indicated that a small amount of Y2O3 could effectively promote the sintering procedure of BABS glass-ceramics.

The Lattice and Thermal Radiation Conductivity of Thermal Barrier Coatings: Models and Experiments

Science.gov (United States)

Zhu, Dongming; Spuckler, Charles M.

2010-01-01

The lattice and radiation conductivity of ZrO2-Y2O3 thermal barrier coatings was evaluated using a laser heat flux approach. A diffusion model has been established to correlate the coating apparent thermal conductivity to the lattice and radiation conductivity. The radiation conductivity component can be expressed as a function of temperature, coating material scattering, and absorption properties. High temperature scattering and absorption of the coating systems can be also derived based on the testing results using the modeling approach. A comparison has been made for the gray and nongray coating models in the plasma-sprayed thermal barrier coatings. The model prediction is found to have a good agreement with experimental observations.

Effect of SiO 2-ZrO 2 supports prepared by a grafting method on hydrogen production by steam reforming of liquefied natural gas over Ni/SiO 2-ZrO 2 catalysts

Science.gov (United States)

Seo, Jeong Gil; Youn, Min Hye; Song, In Kyu

SiO 2-ZrO 2 supports with various zirconium contents are prepared by grafting a zirconium precursor onto the surface of commercial Carbosil silica. Ni(20 wt.%)/SiO 2-ZrO 2 catalysts are then prepared by an impregnation method, and are applied to hydrogen production by steam reforming of liquefied natural gas (LNG). The effect of SiO 2-ZrO 2 supports on the performance of the Ni(20 wt.%)/SiO 2-ZrO 2 catalysts is investigated. SiO 2-ZrO 2 prepared by a grafting method serves as an efficient support for the nickel catalyst in the steam reforming of LNG. Zirconia enhances the resistance of silica to steam significantly and increases the interaction between nickel and the support, and furthermore, prevents the growth of nickel oxide species during the calcination process through the formation of a ZrO 2-SiO 2 composite structure. The crystalline structures and catalytic activities of the Ni(20 wt.%)/SiO 2-ZrO 2 catalysts are strongly influenced by the amount of zirconium grafted. The conversion of LNG and the yield of hydrogen show volcano-shaped curves with respect to zirconium content. Among the catalysts tested, the Ni(20 wt.%)/SiO 2-ZrO 2 (Zr/Si = 0.54) sample shows the best catalytic performance in terms of both LNG conversion and hydrogen yield. The well-developed and pure tetragonal phase of ZrO 2-SiO 2 (Zr/Si = 0.54) appears to play an important role in the adsorption of steam and subsequent spillover of steam from the support to the active nickel. The small particle size of the metallic nickel in the Ni(20 wt.%)/SiO 2-ZrO 2 (Zr/Si = 0.54) catalyst is also responsible for its high performance.

Study of dielectric property on ZrO2 and Al doped ZrO2 nanoparticles

International Nuclear Information System (INIS)

Catherine Siriya Pushpa, K.; Mangayarkarasi, K.; Ravichandran, A.T.; Xavier, A. Robert; Nagabushana, B.M.

2014-01-01

A solution combustion process was used to synthesize ZrO 2 and Al doped ZrO 2 nanoparticles by using Zirconium nitrate and aluminium nitrate as the oxidizer and glycine as fuel. The prepared samples were characterized by several techniques such as X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), UV-visible spectroscopy (UV-vis). The dielectric values of the pelletized samples were examined at room temperature as the function of frequency. XRD shows the structure of the prepared and doped samples. The SEM shows the surface morphology of the pure and doped ZrO 2 nanoparticles. The dielectric property enhances with increase of Al concentration, which is useful in dielectric gates. (author)

In situ formation of CA6 platelets in Al2O3 and Al2O3/ZrO2 matrices

OpenAIRE

Belmonte , M.; SÁnchez-Herencia , A.; Moreno , R.; Miranzo , P.; Moya , J.; Tomsia , A.

1993-01-01

Al2O3 and Al2O3/ZrO2 compacts containing CaO as a dopant have been sintered under different conditions and atmospheres: air, high vacuum (> 10-6torr). SEM observations have been made on the polished surfaces of sintered and also of annealed samples. Only after the annealing treatment in air at temperatures ranging from 1400° to 1 500°C, a massive formation of CA6 platelets was detected in samples sintered in low oxygen partial pressure atmospheres.ln order to clarify the mechanism of formatio...

Diffusion barriers of Al2O3 to reduce the bondcoat-oxidation of MCrAlY alloys

International Nuclear Information System (INIS)

Schmitt-Thomas, K.G.; Dietl, U.

1992-01-01

Under operating conditions in gas turbines plasma sprayed MCrAlY bondcoats (M = Co and/or Ni) for thermal barrier coatings are exposed to a strong oxidation attack. One possibility to reduce bondcoat oxidation is the application of diffusion barriers. Onto the bondcoat, diffusion barriers of Al 2 O 3 are deposited by CVD, PVD and plasma pulse process. The oxidation behaviour of these coating systems were examined at a temperature of 1273 K for times up to 250 hours. The CVD and PVD Al 2 O 3 - coated specimens show compared to the uncoated specimens smaller oxidation rates. The porous Al 2 O 3 coatings, produced by plasma pulse process are not fit for oxidation protection of the bondcoat. There is hope for further improvement of the oxidation resistance by optimizing the CVD- and PVD-process parameters. (orig.) [de

Valence electron structure and properties of stabilized ZrO2

Institute of Scientific and Technical Information of China (English)

LI JinPing; HAN JieOai; MENG SongHe; ZHANG XingHong

2008-01-01

To reveal the properties of stabilizers in ZrO2 on nanoscopic levels,the valence elec-tron structures of four stable ZrO2 phases and c-ZrO2 were analyzed on the basis of the empirical electron theory of solids and molecules.The results showed that the hybridization levels of Zr atoms in c-ZrO2 doped with Ca and Mg dropped from B17 to B13,the hybridization levels of Zr atoms in c-ZrO2 doped with Y and Ce dropped from B17 to B15,and that the four stabilizing atoms all made the hybridization levels of O atoms drop from level 4 to level 2.The numbers of covalent electrons in the strongest covalent bond in the descending order are c-ZrO2>ZrCeO2>ZrYOZrMgO>ZrCaO.The bond energies of the strongest covalent bond and the melting points of the solid solutions in the descending order are ZrCeO2>c-ZrO2>ZrYO>ZrMgO>ZrCaO.The percent-ages of the total number of covalent electrons in the descending order arec-ZrO2>ZrYO> ZrCeO2>ZrMgO> ZrCaO.From the above analysis,it can be concluded that the stabilizing degrees of the four stabilizers in the descending order are CaO> MgO>Y2O3>CeO2.

Cobalt doped ZrO2 decorated multiwalled carbon nanotube: A promising nanocatalyst for photodegradation of indigo carmine and eosin Y dyes

Directory of Open Access Journals (Sweden)

William Wilson Anku

2016-08-01

Full Text Available This paper reports the degradation of indigo carmine and eosin Y dyes in water, catalyzed by cobalt and multiwalled carbon nanotube modified zirconium oxide nanocomposite (Co-ZrO2-MWCNTs under simulated visible light. The bare ZrO2, ZrO2-MWCNTs, Co-ZrO2 and Co-ZrO2-MWCNTs with different percentage compositions of cobalt were synthesized by homogeneous co-precipitation method. Characterization of the prepared nanocomposites was carried out using X-Ray powder Diffraction (XRD, Fourier Transformer Infrared (FTIR Spectroscopy, Transmission Electron Microscopy (TEM, Raman Spectroscopy, (UV–Vis-Spectroscopy and Energy Dispersive Spectroscopy (EDS for their structure, formation, morphology, size and elemental analysis. The experimental results indicated that all the cobalt and MWCNTs modified nanocomposites demonstrated higher photocatalytic activities compared to the bare ZrO2. The most efficient catalyst (0.5% Co-ZrO2-MWCNTs with the band gap and Ka values of 5.21 eV and 16.86×10−3 min−1 respectively exhibited 98% degradation efficiency toward indigo carmine and 87% toward eosin Y in 180 min.

Síntesis de nanocomposites NTC-13%ZrO2 – (87-xAl2O3-xFe

Directory of Open Access Journals (Sweden)

Legorreta García, F.

2014-04-01

Full Text Available Carbon nanotubes (CNT in a ceramic matrix – Fe, NTC-13%ZrO2 – (87-xAl2O3-xFe, (x = 1.9, 4.6 y 6.4%, were obtained using a combustion synthesis urea-nitrate, calcination treatment and chemical vapor deposition (CCVD in H2-CH4 atmosphere. The effect of the addition of Fe ions on the ceramic matrix was studied and presented. The ceramic powder obtained was calcined at 1200 °C for 2 h to modify the phases present in the solid solution. Subsequently it was introduced in a H2-CH4 reducing atmosphere at 1000 °C in order to promote the formation of CNT in the matrix. Both, the solid solution obtained and the composite materials were characterized by X-ray diffraction (XRD and high resolution scanning electron microscopy (HRSEM. Carbon content and specific surface also were determined. The quality and quantity of CNT present in the nanocomposite powder were related to the concentration of Fe, which significantly modifies their carbon content and specific surface.Mediante una síntesis por combustión ureica-nitratos, calcinación y la aplicación de un tratamiento de deposición química catalítica de vapor (CCVD en una atmósfera H2-CH4, se obtuvieron polvos nanocomposites: nanotubos de carbono (NTC en una matriz cerámica –Fe, NTC-13%ZrO2 – (87-xAl2O3-xFe, (x = 1.9, 4.6 y 6.4 %. El efecto de la adición de iones Fe sobre la matriz cerámica es estudiado y presentado. El polvo cerámico obtenido es calcinado a 1200 °C durante 2 h para modificar las fases presentes del composite. Posteriormente es sometido a una atmósfera reductora H2-CH4 a 1000 °C con la finalidad de promover la formación de NTC in situ en la matriz. Tanto el composite obtenido, como el material nanocomposite fueron caracterizados por difracción de rayos X (DRX y microscopía electrónica de barrido de alta resolución (MEB. También se determinó el contenido de carbono y la superficie específica. Se observó que la calidad y cantidad de NTC presentes en los polvos

Thermoluminescent characteristics of ZrO2:Nd films

International Nuclear Information System (INIS)

Vera B, G.; Rivera M, T.; Azorin N, J.; Falcony G, C.; Garcia H, M.; Martinez S, E.

2002-01-01

In this work it is exposed the obtained results after analysing the photo luminescent and thermoluminescent characteristics of activated zirconium oxide with neodymium (ZrO 2 :Nd) and its possible application in the UV radiation dosimetry. The realized experiments had as objective to study the characteristics such as the optimum thermal erased treatment, the influence of light on the response, the response depending on the wavelength, the fadeout of the information, the temperature effect, the response depending on the time and the recurring of the response. The results show that the ZrO 2 :Nd is a promising material to be used as Tl dosemeter for the UV radiation. (Author)

Gamma-induced defect production in ZrO2-Y2O3 crystals with different defectiveness

International Nuclear Information System (INIS)

Ashurov, M.Kh.; Amonov, M.Z.; Rakov, A.F.

2002-01-01

Full text: The defectiveness degree of ZrO 2 -Y 2 O 3 crystals depends on stabilizer concentration. The work is aimed at study gamma-induced defect production in crystals with different concentration of stabilizer and defects generated by neutron irradiation. Absorption spectra were measured with Specord M-40. It was found, that after gamma-irradiation of as-grown crystals up to some dose the intensity of absorption band at 420 nm reaches the maximum level of saturation. The dose of saturation depends of the concentration of stabilizer. It means that gamma-radiation does not produce any additional defects of structure. The oxygen vacancies existing in as-grown crystals are filled by the radiation induced electrons. Since the number of oxygen vacancies depends on the stabilizer concentration, then all these vacancies can be occupied by electrons at different gamma-doses. In crystals pre-irradiated with different neutron fluences followed by gamma-irradiation, the intensity of absorption bands at 420 and 530 nm increases in two stages. The gamma-dose of the second stage beginning decreases as the neutron fluence grows. The first stage of the absorption increase is due to developing of vacancies existing in as-grown crystals. The second stage is caused by generation of additional vacancies as the result of non-radiative exciton decay near the existing structure damages. The decrease of the gamma-dose, when the second stage of vacancy accumulation begins, results from the neutron induced structure damage degree

Resistive switching in ZrO2 based metal-oxide-metal structures

International Nuclear Information System (INIS)

Kaerkkaenen, Irina

2014-01-01

The goal of this work is a deeper understanding of the influence of the (i) metal-oxide-metal (MOM) layer stacks configuration, (ii) the oxide films microstructure, (iii) and their defect structure on the appearance of different switching modes, i.e. unipolar (UP) and bipolar (BP). The first part deals with the fabrication of ZrO 2 thin films by an industrial compatible atomic layer deposition (ALD) process, the chemical, structural and morphological characterization of the films, the growth of ZrO 2 /TiO 2 bilayers, the integration of the layers into metal-oxide-metal (MOM) devices and the electrical characterization with focus on the RS behavior. In the second part the effect of the device structure, in particular the thickness of the electrochemical active electrode (EAE) and the ZrO 2 film morphology, on the RS switching polarity of Pt/ZrO 2 /(EAE) cells is discussed. ZrO 2 films and ZrO 2 /TiO 2 bilayers were grown by ALD and were carefully structurally and electrically characterized. The ZrO 2 films grown from Zr[N(CH 3 )C 2 H 5 ] 4 (TEMA-Zr) at 240 C were polycrystalline with a mixture of cubic/tetragonal phases. ALD/H 2 O-ZrO 2 films exhibited a random oriented polycrystalline structure, whereas the ALD/O 3 -ZrO 2 films consisted of preferably oriented cubic shaped grains. Pt/ZrO 2 /Ti/Pt structures with a Ti top electrode (TE) thickness of 5 to 20 nm showed unipolar type RS behavior, while by increasing the Ti TE thickness a gradual change of switching polarity from unipolar to bipolar with a completely bipolar type RS behavior for a Ti TE thickness of 40 nm is found. The switching in Pt/ZrO 2 /TiO 2 /Ti/Pt devices was unipolar, comparable to Pt/ZrO 2 /Ti/Pt cells. In contrast, bilayers with the reverse structure, Pt/TiO 2 /ZrO 2 /Ti/Pt, showed non-switching behavior. The effect of the cells stack structure on the polarity of the RS behavior was studied in detail for 20 nm thick ZrO 2 films grown by an ozone based ALD process and integrated into Pt/ZrO 2

Valence electron structure and properties of stabilized ZrO2

Institute of Scientific and Technical Information of China (English)

2008-01-01

To reveal the properties of stabilizers in ZrO2 on nanoscopic levels, the valence electron structures of four stable ZrO2 phases and c-ZrO2 were analyzed on the basis of the empirical electron theory of solids and molecules. The results showed that the hybridization levels of Zr atoms in c-ZrO2 doped with Ca and Mg dropped from B17 to B13, the hybridization levels of Zr atoms in c-ZrO2 doped with Y and Ce dropped from B17 to B15, and that the four stabilizing atoms all made the hybridization levels of O atoms drop from level 4 to level 2. The numbers of covalent electrons in the strongest covalent bond in the descending order are c-ZrO2>Zr0.82Ce0.18O2> Zr0.82Y0.18O1.91>Zr0.82Mg0.18O1.82>Zr0.82Ca0.18O1.82. The bond energies of the strongest covalent bond and the melting points of the solid solutions in the descending order are Zr0.82Ce0.18O2> c-ZrO2>Zr0.82Y0.18O1.91>Zr0.82Mg0.18O1.82>Zr0.82Ca0.18O1.82. The percent-ages of the total number of covalent electrons in the descending order are c-ZrO2>Zr0.82Y0.18O1.91> Zr0.82Ce0.18O2>Zr0.82Mg0.18O1.82> Zr0.82Ca0.18O1.82. From the above analysis, it can be concluded that the stabilizing degrees of the four stabilizers in the descending order are CaO> MgO>Y2O3>CeO2.

Study on the Effect of Different Fe2O3/ZrO2 Ratio on the Properties of Silicate Glass Fibers

Directory of Open Access Journals (Sweden)

Jianxun Liu

2017-01-01

Full Text Available A series of silicate glass fibers with different ratios of Fe2O3/ZrO2 were prepared, and their corrosion resistance, mass loss, and strength loss were characterized. The crystallization and melting properties of the fibers were analyzed by differential scanning calorimetry (DSC, high temperature viscometer, and high temperature microscope. The results show that the deformation temperature, sphere temperature, hemisphere temperature, and crystallization temperature of the fiber initially decrease and then increase with the increase of Fe2O3/ZrO2 ratio, while the molding temperature decreases with the increase of the ratio of Fe2O3/ZrO2. When the ratio is close to 1 : 1, its alkali resistance is almost same as that of AR-glass fiber, and the drawing process performance is better. However, with the increase of the ratio, its alkali resistance continues to decline and the poor wire drawing performance is not conducive to the drawing operation.

Spark plasma sintering and mechanical properties of $ZrO_{2} (Y_{2}O_{3})-Al_{2}O_{3}$ composites

CERN Document Server

Jin Sheng H; Dalla Torre, S; Miyamoto, H; Miyamoto, K

2000-01-01

Spark plasma sintering (SPS) was conducted on nanocrystalline ZrO/sub 2/(Y/sub 2/O/sub 3/)-20 mol% Al/sub 2/O/sub 3/ powder at a heat rate of 600 degrees C/min with a short holding time. Full density was obtained at sintering temperatures >1300 degrees C. Considerable grain growth occurred relative to the initial powder particles, but smaller grain size and higher density can be obtained as compared to hot-pressing. High flexural strength and fracture toughness were also achieved for the SPS-resulted composite. (8 refs).

Chemical synthesis, characterization studies and reactivity of a catalytic material based on ZrO2-H3PW12O40

International Nuclear Information System (INIS)

Hernandez Enriquez, Juan Manuel; Garcia Alamilla, Ricardo; Paramo Garcia, Ulises; Rodrigo, Rebeca Silva; Garcia Serrano, Luz Arcelia

2013-01-01

In this work, the preparation and characterization of materials such as zirconium oxide (ZrO 2 ) and phosphotungstic acid promoted zirconium oxide (ZrO 2 -H 3 PW 12 O 40 ) is presented. Physico-chemical characterization results showed that addition of H 3 PW 12 O 40 acted as both a textural and chemical promoter of zirconium oxide. The incorporation of phosphotungstic acid into the ZrO 2 matrix delayed the sintering of the material and stabilized ZrO 2 in the tetragonal phase. ZrO 2 acidity was also enhanced, developing strong acid sites on its surface. The Pt/ZrO 2 -H 3 PW 12 O 40 catalyst was active for n-pentane isomerization at 250 deg C, exhibiting high selectivity to iso-pentane (95%). This result is probably due to its suitable acidity (author)

Photo-, sono- and sonophotocatalytic degradation of methylene blue using Fe3O4/ZrO2 composites catalysts

Science.gov (United States)

Kristianto, Y.; Taufik, A.; Saleh, R.

2017-07-01

In the present work, magnetite material Fe3O4/ZrO2 with various molar ratios was prepared by the two-step method (sol-gel followed by the ultrasonic-assisted method). The as-prepared samples were fairly characterized by various characterization methods, such as X-ray Diffraction (XRD), Vibrating Sample Magnetometer (VSM), Fourier Transform Infrared (FT-IR) and Thermal Gravimetric Analysis (TGA). The catalytic performance of the as-prepared samples was evaluated based on the degradation of methylene blue under UV light, ultrasound and combination of UV and ultrasound irradiation. The results revealed that the sample with Fe3O4:ZrO2 molar ratio of 0.5:1 showed the best catalytic performance under UV, ultrasound and UV + ultrasound irradiation. The degradation of methylene blue follows the order: sonophotocatalytic > sonocatalytic > photocatalytic. In addition, the effect of various scavengers has also been studied. Furthermore, all prepared samples could be used as a convenient recyclable catalyst.

Optical and structural characterization of Ge clusters embedded in ZrO2

Science.gov (United States)

Agocs, E.; Zolnai, Z.; Rossall, A. K.; van den Berg, J. A.; Fodor, B.; Lehninger, D.; Khomenkova, L.; Ponomaryov, S.; Gudymenko, O.; Yukhymchuk, V.; Kalas, B.; Heitmann, J.; Petrik, P.

2017-11-01

The change of optical and structural properties of Ge nanoclusters in ZrO2 matrix have been investigated by spectroscopic ellipsometry versus annealing temperatures. Radio-frequency top-down magnetron sputtering approach was used to produce the samples of different types, i.e. single-layers of pure Ge, pure ZrO2 and Ge-rich-ZrO2 as well as multi-layers stacked of 40 periods of 5-nm-Ge-rich-ZrO2 layers alternated by 5-nm-ZrO2 ones. Germanium nanoclusters in ZrO2 host were formed by rapid-thermal annealing at 600-800 °C during 30 s in nitrogen atmosphere. Reference optical properties for pure ZrO2 and pure Ge have been extracted using single-layer samples. As-deposited multi-layer structures can be perfectly modeled using the effective medium theory. However, annealed multi-layers demonstrated a significant diffusion of elements that was confirmed by medium energy ion scattering measurements. This fact prevents fitting of such annealed structure either by homogeneous or by periodic multi-layer models.

Study of spinodal decomposition and formation of nc-Al2O3/ZrO2 nanocomposites by combined ab initio density functional theory and thermodynamic modeling

International Nuclear Information System (INIS)

Sheng, S.H.; Zhang, R.F.; Veprek, S.

2011-01-01

Using ab initio density functional theory, the equilibrium properties, such as the total energy, the molar volume, the bulk modulus and its first derivative, as well as the formation enthalpy of monoclinic ZrO 2 and hexagonal α-Al 2 O 3 phases, were calculated and compared with the published theoretical and experimental data. Based on the good agreement of these data, we calculated the lattice instabilities of hypothetical binary hexagonal Zr 2 O 3 and monoclinic AlO 2 , and the interaction parameters of ternary Zr 1-x Al x O y solid solutions. The binodal and spinodal diagrams were then constructed to predict the possibility of the formation of oxide-based nanocomposites which may display hardness enhancement above that of the solid solutions. It is shown that exponential dependence of the interaction parameter on temperature yields the most reliable results. The system should undergo spinodal phase segregation within the composition range that is relevant for the formation of hard or superhard nanocomposites with high thermal and oxidation stability, which are important for their applications.

Improved conversion efficiency of dye sensitized solar cell using Zn doped TiO_2-ZrO_2 nanocomposite

International Nuclear Information System (INIS)

Tomar, Laxmi J.; Bhatt, Piyush J.; Desai, Rahul K.; Chakrabarty, B. S.; Panchal, C. J.

2016-01-01

TiO_2-ZrO_2 and Zn doped TiO_2-ZrO_2 nanocomposites were prepared by hydrothermal method for dye sensitized solar cell (DSSC) application. The structural and optical properties were investigated by X –ray diffraction (XRD) and UV-Visible spectroscopy respectively. XRD results revealed the formation of material in nano size. The average crystallite size is 22.32 nm, 17.41 nm and 6.31 nm for TiO_2, TiO_2-ZrO_2 and Zn doped TiO_2-ZrO_2 nanocomposites respectively. The optical bandgap varies from 2.04 eV to 3.75 eV. Dye sensitized solar cells were fabricated using the prepared material. Pomegranate juice was used as a sensitizer and graphite coated conducting glass plate was used as counter electrode. The I – V characteristics were recorded to measure photo response of DSSC. Photovoltaic parameter like open circuit voltage, power conversion efficiency, and fill factor were evaluated for fabricated solar cell. The power conversion efficiency of DSSC fabricated with TiO_2, TiO_2-ZrO_2 and Zn doped TiO_2-ZrO_2 nanocomposites were found 0.71%, 1.97% and 4.58% respectively.

Improved conversion efficiency of dye sensitized solar cell using Zn doped TiO2-ZrO2 nanocomposite

Science.gov (United States)

Tomar, Laxmi J.; Bhatt, Piyush J.; Desai, Rahul K.; Chakrabarty, B. S.; Panchal, C. J.

2016-05-01

TiO2-ZrO2 and Zn doped TiO2-ZrO2 nanocomposites were prepared by hydrothermal method for dye sensitized solar cell (DSSC) application. The structural and optical properties were investigated by X -ray diffraction (XRD) and UV-Visible spectroscopy respectively. XRD results revealed the formation of material in nano size. The average crystallite size is 22.32 nm, 17.41 nm and 6.31 nm for TiO2, TiO2-ZrO2 and Zn doped TiO2-ZrO2 nanocomposites respectively. The optical bandgap varies from 2.04 eV to 3.75 eV. Dye sensitized solar cells were fabricated using the prepared material. Pomegranate juice was used as a sensitizer and graphite coated conducting glass plate was used as counter electrode. The I - V characteristics were recorded to measure photo response of DSSC. Photovoltaic parameter like open circuit voltage, power conversion efficiency, and fill factor were evaluated for fabricated solar cell. The power conversion efficiency of DSSC fabricated with TiO2, TiO2-ZrO2 and Zn doped TiO2-ZrO2 nanocomposites were found 0.71%, 1.97% and 4.58% respectively.

Effect of thermal annealing on resistance switching characteristics of Pt/ZrO2/TiN stacks

International Nuclear Information System (INIS)

Kim, Jonggi; Lee, Kyumin; Kim, Yonjae; Na, Heedo; Ko, Dae-Hong; Sohn, Hyunchul; Lee, Sunghoon

2013-01-01

In this study, the effect of thermal annealing on both the physical properties and the resistive switching properties of ZrO 2 films deposited by atomic layer deposition (ALD) method were investigated for its potential application to non-volatile memory devices. The ZrO 2 films in the Pt/ZrO 2 /TiN structure exhibited unipolar and bipolar resistance switching behaviors depending on the nature of the bias applied to Pt top electrodes for the electro-forming process. For unipolar switching, the resistance of the high resistance state (HRS) was reduced with increasing annealing temperature, accompanied with the increase of metallic Zr in the annealed ZrO 2 films. In contrast, the HRS resistance in the bipolar switching was increased while the low resistance state (LRS) resistance was decreased with increasing annealing temperature, producing a greater change in resistance. SIMS and EDX showed that the thickness of interfacial TiO x N y layer between the ZrO 2 and the TiN bottom electrode was enlarged with annealing. The enlarged TiO x N y layer was expected to produce the reduction of LRS resistance with the increase of HRS resistance in the bipolar resistance switching. - Highlights: • Effect of thermal annealing on resistive switching of ZrO 2 was investigated. • Both unipolar and bipolar switching were shown in the Pt/ZrO 2 /TiN stack. • TiO x N y interface layer was enlarged with increasing annealing temperature. • TiO x N y interface plays an important role in resistive switching properties

The influence of interfacial barrier engineering on the resistance switching of In2O3:SnO2/TiO2/In2O3:SnO2 device

International Nuclear Information System (INIS)

Liu Zi-Yu; Zhang Pei-Jian; Meng Yang; Li Dong; Meng Qing-Yu; Li Jian-Qi; Zhao Hong-Wu

2012-01-01

The I—V characteristics of In 2 O 3 :SnO 2 /TiO 2 /In 2 O 3 :SnO 2 junctions with different interfacial barriers are investigated by comparing experiments. A two-step resistance switching process is found for samples with two interfacial barriers produced by specific thermal treatment on the interfaces. The nonsynchronous occurrence of conducting filament formation through the oxide bulk and the reduction in the interfacial barrier due to the migration of oxygen vacancies under the electric field is supposed to explain the two-step resistive switching process. The unique switching properties of the device, based on interfacial barrier engineering, could be exploited for novel applications in nonvolatile memory devices. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Atomic layer deposition and properties of mixed Ta2O5 and ZrO2 films

Directory of Open Access Journals (Sweden)

Kaupo Kukli

2017-02-01

Full Text Available Thin solid films consisting of ZrO2 and Ta2O5 were grown by atomic layer deposition at 300 °C. Ta2O5 films doped with ZrO2, TaZr2.75O8 ternary phase, or ZrO2 doped with Ta2O5 were grown to thickness and composition depending on the number and ratio of alternating ZrO2 and Ta2O5 deposition cycles. All the films grown exhibited resistive switching characteristics between TiN and Pt electrodes, expressed by repetitive current-voltage loops. The most reliable windows between high and low resistive states were observed in Ta2O5 films mixed with relatively low amounts of ZrO2, providing Zr to Ta cation ratio of 0.2.

Fabrication of Metal Nanoparticle Arrays in the ZrO2(Y, HfO2(Y, and GeOx Films by Magnetron Sputtering

Directory of Open Access Journals (Sweden)

Oleg Gorshkov

2017-01-01

Full Text Available The single sheet arrays of Au nanoparticles (NPs embedded into the ZrO2(Y, HfO2(Y, and GeOx (x≈2 films have been fabricated by the alternating deposition of the nanometer-thick dielectric and metal films using Magnetron Sputtering followed by annealing. The structure and optical properties of the NP arrays have been studied, subject to the fabrication technology parameters. The possibility of fabricating dense single sheet Au NP arrays in the matrices listed above with controlled NP sizes (within 1 to 3 nm and surface density has been demonstrated. A red shift of the plasmonic optical absorption peak in the optical transmission spectra of the nanocomposite films (in the wavelength band of 500 to 650 nm has been observed. The effect was attributed to the excitation of the collective surface plasmon-polaritons in the dense Au NP arrays. The nanocomposite films fabricated in the present study can find various applications in nanoelectronics (e.g., single electronics, nonvolatile memory devices, integrated optics, and plasmonics.

First-principles characterization of a heteroceramic interface: ZrO2(001) deposited on an alpha-Al2O3(1(1)over-bar02) substrate

DEFF Research Database (Denmark)

Christensen, Asbjørn; Carter, Emily A.

2000-01-01

We have studied an alumina/zirconia interface using the all-electron projector augmented wave formalism within density functional theory. We present the electronic, structural, and energetic properties of the ZrO2(001)/(alpha -Al2O3(1 (1) over bar 02) interface as well as of the free alpha -Al2O3......(1 (1) over bar 02) and ZrO2(001) surfaces. We find that the generalized gradient correction significantly lowers the oxide surface energies, compared to values obtained by the local density approximation. The monoclinic-tetragonal transition in ZrO2(001) thin films is discussed as well as strain...... effects involved in the interface formation. The stoichiometric alumina/zirconia interface is found to be weakly bonded, regardless of the film thickness, and the ZrO2(001)/alpha -Al2O3(1 (1) over bar 02) interface has a rather epitaxial character, due to a low lattice mismatch of similar to4%. The impact...

Study of the ZrO2-FeO-Fe2O3 system by thermogravimetry in partial pressure of oxygen and temperatures up to 15000C

International Nuclear Information System (INIS)

Goldschmidt, R.H.; Kiminami, A.

1987-01-01

The dissociation of iron oxide in the ZrO 2 -FeO-Fe 2 O 3 system was investigated in function of the temperature and the constant partial pressure of oxygen by thermal gravimetric analysis. The equilibrium diagram was constructed where the equilibrium relation between the solid phase of zirconium oxide, hematite and magnetite in 1437 0 C and PO 2 = 0.21 atm/m, as well as the equilibrium relation between the solid phase of zirconium oxide and hematite in lower temperatures than 1437 0 C were determined [pt

Air Plasma-Sprayed La2Zr2O7-SrZrO3 Composite Thermal Barrier Coating Subjected to CaO-MgO-Al2O3-SiO2 (CMAS)

Science.gov (United States)

Cai, Lili; Ma, Wen; Ma, Bole; Guo, Feng; Chen, Weidong; Dong, Hongying; Shuang, Yingchai

2017-08-01

La2Zr2O7-SrZrO3 composite thermal barrier coatings (TBCs) were prepared by air plasma spray (APS). The La2Zr2O7-SrZrO3 composite TBCs covered with calcium-magnesium-aluminum-silicate (CMAS) powder, as well as the powder mixture of CMAS and spray-dried La2Zr2O7-SrZrO3 composite powder, were heat-treated at 1250 °C in air for 1, 4, 8, and 12 h. The phase constituents and microstructures of the reaction products were characterized by x-ray diffraction, scanning electron microscopy, and energy-dispersive spectroscopy. Experimental results showed that the La2Zr2O7-SrZrO3 composite TBCs had higher CMAS resistance than 8YSZ coating. A dense new layer developed between CMAS and La2Zr2O7-SrZrO3 composite TBCs during interaction, and this new layer consisted mostly of apatite (Ca2La8(SiO4)6O2) and c-ZrO2. The newly developed layer effectively protected the La2Zr2O7-SrZrO3 composite TBCs from further CMAS attack.

Electron paramagnetic resonance study of Ce doped partially stabilized ZrO2 crystals

Directory of Open Access Journals (Sweden)

Mikhail А. Borik

2017-09-01

Full Text Available ZrO2 (PSZ solid solutions crystals stabilized with yttrium and cerium oxides have been studied using electron paramagnetic resonance (EPR in the X and Q ranges. Zr3+ have been observed centers in the as-annealed ZrO2 crystals stabilized only by yttrium oxide (2.8 mol% Y2O3. Another type of paramagnetic-O-centers appear as a result of CeO2 addition to ZrO2 crystals along with yttrium oxide. To estimate the concentration of Ce3+ ions in PZS crystals, we recorded the EPR spectra in the presence of a reference at 7 K. Paramagnetic Ce3+ ions have been identified and their relative amount in the PSZ crystals before and after high-temperature heat treatment has been assessed. Annealing in air leads decreases the concentration of Ce3+ ions for all the test compositions and changes the color of the crystals from red to white. After annealing of the sample 2.0Y0.8Ce3Zr, the amount of paramagnetic Ce3+ ions decreased approximately twofold. Paramagnetic centers from Ce3+ have not been detected in the specimen with a low cerium content of 0.1 mol% after annealing which indicates the complete transition of Ce3+ to the Ce4+ state. We show that the forming cerium paramagnetic centers are bound by strong exchange interactions. No angular dependence of the EPR lines of the paramagnetic Ce3+ cations on the applied external magnetic field has been observed. Probable origin of the absence of angular dependence is that the impurity rare-earth ions are located close to one another, forming impurity clusters with an effective spin of Seff=1/2.

Spontaneous nano-clustering of ZrO2 in atomic layer deposited LayZr1-yOx thin films: Part 1 - Material characterization

NARCIS (Netherlands)

Klootwijk, J.H.; Jinesh, K.B.; Wolters, R.A.M.; Roozeboom, F.; Besling, W.

2008-01-01

During atomic layer deposition (ALD) of uniform LayZr1-yOx thin films, spontaneous segregation of ZrO2 nanocrystals takes place that are embedded in an amorphous La2O3 matrix. This occurs if the Zr content in the LayZr1-yOx film is above 30% i.e. if the pulse ratio between the lanthanum precursor

Investigation on microstructure and thermal properties of in-situ synthesized Cu-ZrO2 nanocomposites

International Nuclear Information System (INIS)

Elmahdy, Marwa; Abouelmagd, Gamal; Mazen, Asaad A.

2017-01-01

Cu-ZrO 2 nanocomposites were prepared by an in-situ reactive synthesis of copper nitrate Cu(NO 3 ) 2 and zirconium oxychloride ZrOCl 2 . Zirconia (ZrO 2 ) was added by 2.5, 5 and 10 wt.% to the Cu matrix to assess its effect on thermal conductivity and thermal expansion behavior. The results showed that ZrO 2 nanoparticles (30-50 nm) were homogeneously distributed in the copper matrix. The measured thermal conductivity for the Cu-ZrO 2 nanocomposites decreased from 372.8 to 94.4 W m -1 K -1 with increasing ZrO 2 content from 0 to 10 wt.%. Cu-10 wt.% ZrO 2 nanocomposite yields a low thermal conductivity of 94.4 W . m -1 K -1 along with a low coefficient of thermal expansion, 11.47 x 10 -6 K -1 .

Improvement of resistive switching characteristics in ZrO2 film by embedding a thin TiOx layer

International Nuclear Information System (INIS)

Li Yingtao; Long Shibing; Lv Hangbing; Liu Qi; Wang Yan; Zhang Sen; Lian Wentai; Wang Ming; Zhang Kangwei; Xie Hongwei; Liu Ming; Liu Su

2011-01-01

The stabilization of the resistive switching characteristics is important to resistive random access memory (RRAM) device development. In this paper, an alternative approach for improving resistive switching characteristics in ZrO 2 -based resistive memory devices has been investigated. Compared with the Cu/ZrO 2 /Pt structure device, by embedding a thin TiO x layer between the ZrO 2 and the Cu top electrode, the Cu/TiO x -ZrO 2 /Pt structure device exhibits much better resistive switching characteristics. The improvement of the resistive switching characteristics in the Cu/TiO x -ZrO 2 /Pt structure device might be attributed to the modulation of the barrier height at the electrode/oxide interfaces.

Synthesis and mechanical properties of stabilized zirconia ceramics: MgO-ZrO_2 and Y_2O_3-MgO- ZrO_2

International Nuclear Information System (INIS)

Yamagata, C.; Mello-Castanho, S.R.H.; Paschoal, J.O.A.

2014-01-01

Precursor MgO-ZrO_2 and Y_2O_3-MgO-ZrO_2 ceramic powders were synthesized by the method of co-precipitation and characterized by techniques such as laser diffraction, QELS (Quasi Elastic Light Scattering), XRD, BET, and SEM. Nanoscale powders with specific surface area higher than 60 m"2. g"-"1 was achieved. Sintered ceramic obtained from the synthesized powders, were characterized to mechanical tests using Vickers indentation technique. The addition of Y_2O_3 promoted an increase in hardness of the ceramics and total cubic crystalline phase stabilization. (author)

Direct write printing of three-dimensional ZrO2 biological scaffolds

International Nuclear Information System (INIS)

Li, Ya-yun; Li, Long-tu; Li, Bo

2015-01-01

Graphical abstract: Three-dimensional (3D) zirconium dioxide (ZrO 2 ) scaffolds have been fabricated for biological engineering by direct write printing method. The water-based ZrO 2 ink with a solid content fraction of 70 wt% was deposited through a fine nozzle on the substrate by a layer-by-layer sequence to produce the 3D microperiodic structures. Under a microscope, the proliferation of HCT116 cells can be observed around the 3D ZrO 2 scaffolds. 3D porous internal architecture is beneficial for cell growth by providing more locations for cell attachment and proliferation. The largest value of compressive strength reached 10 MPa, which is more than that of the hydroxyapatite (HAp) scaffold. The ability of printing 3D scaffolds with the high precise control of their internal architecture is the unique characteristics performed by the direct write technique, which will provide potential application of biomaterials and tissue engineering scaffolds. (a) Top view of the sintered 3D woodpile ZrO 2 scaffold; (b) top view of the sintered 3D cylindrical ZrO 2 scaffold. - Highlights: • 3D cylindrical and woodpile ZrO 2 scaffolds were fabricated by direct write printing method. • The compressive strength of the sample with porosity about 63% was 8 MPa. • The compressive strength of the porosity 55% sample was 10 MPa. • 3D porous ZrO 2 scaffolds with interconnected architecture are beneficial for cell attachment and proliferation. - Abstract: Three-dimensional (3D) zirconium dioxide (ZrO 2 ) scaffolds have been fabricated for biological engineering by direct write printing method. The water-based ZrO 2 ink with a solid content fraction of 70 wt% was deposited through a fine nozzle on the substrate by a layer-by-layer sequence to produce the 3D microperiodic structures. The preparation and the rheological behavior of this ink, as well as the principles of the direct write printing process were investigated systematically. Sintered at 1250 °C for 4 h was the optimal

Growth and thermal oxidation of Ru and ZrO2 thin films as oxidation protective layers

NARCIS (Netherlands)

Coloma Ribera, R.

2017-01-01

This thesis focuses on the study of physical and chemical processes occurring during growth and thermal oxidation of Ru and ZrO2 thin films. Acting as oxidation resistant capping materials to prevent oxidation of layers underneath, these films have several applications, i.e., in microelectronics

Evaluation of commercial and sulfated ZrO_2 aiming application catalysis

International Nuclear Information System (INIS)

Silva, F.N.; Dantas, J.; Costa, A.C.F.M.; Pallone, E.M.J.A.; Dutra, R.C.L.

2014-01-01

This study evaluates the performance of commercial and sulfated ZrO_2 for future application in catalysis. Commercial ZrO_2 was provided by the company Saint-Gobain Zirpro. The sulfation occurred with SO_4"-"2 ion content of 30% compared to the mass of ZrO_2. The samples were characterized by XRD, FTIR, EDX and GD. The results revealed the formation of a monoclinic phase for the commercial sample, and a monoclinic major phase with tetragonal traces for the sulfated sample. The commercial ZrO_2 showed a narrow, bimodal and asymmetric agglomerates distribution, while the sulfated sample showed a narrow, tetramodal and asymmetric agglomerates distribution. The presence of traces of the tetragonal phase in the SO_4"-"2/ZrO_2 XRD, and the presence of SO_3 in the EDX were good indicators for future use in catalysis to provide ester. (author)

Preparation of YBa2Cu3O7-δ powders by the thermal decomposition of a heteronuclear complex, CuY1/3Ba2/3(dhbaen)(NO3)1/3(H2O)3

International Nuclear Information System (INIS)

Hasegawa, E.; Aono, H.; Sadaoka, Y.; Traversa, E.

1999-01-01

YBa 2 Cu 3 O 7-δ powders were prepared by the thermal decomposition of a heteronuclear complex, CuY 1/3 Ba 2/3 (dhbaen)(NO 3 ) 1/3 (H 2 O) 3 . The products of the complex thermal decomposition were analyzed by TG-DTA, XRD, SEM-Auger and XPS. The decomposition of the CuY 1/3 Ba 2/3 -complex was obtained at about 500 C and the product was a mixture of oxides and carbonates. The formation of YBa 2 Cu 3 O 7-δ proceeded at 800 C, with a gradual decomposition of the carbonates. A homogeneous distribution of each element, Y, Ba, and Cu, was observed for the decomposed CuY 1/3 Ba 2/3 -complex by SEM-Auger analysis. The binding energy values of Ba3d 5/2 and O1s photolines from Ba and O in the superconductive lattice did not shift during the sputtering period. Furthermore, the formation of Ba rich regions on the surface was depressed by using the complex as a starting material for homogeneous 123-oxide, YBa 2 Cu 3 O 7-δ . (orig.)

Progressive damage during thermal shock cycling of D-gun sprayed thermal barrier coatings with hollow spherical ZrO{sub 2}-8Y{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Ke, P.L. [State Key Lab for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China) and School of Metallurgy and Materials, University of Birmingham, Birmingham B15 2TT (United Kingdom)]. E-mail: csun@imr.ac.cn; Wang, Q.M. [State Key Lab for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Gong, J. [State Key Lab for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Sun, C. [State Key Lab for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China); Zhou, Y.C. [State Key Lab for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

2006-11-05

Thermal shock cycling behaviors of D-gun sprayed TBCs with a hollow spherical ZrO{sub 2}-8Y{sub 2}O{sub 3} (HSP-YSZ) top coat and NiCrAlY bond coat on directionally solidified Ni-base superalloys DZ125 were investigated at high temperature (1100 deg. C) {r_reversible} room temperature (RT) repeatedly by water quenching. Scanning electron microscopy (SEM) was used to characterize the coating microstructure and failure morphology. The results showed that failure of the D-gun sprayed TBC starts with crack initiation along the splats boundary in the ceramic top coat and the non-alumina oxides. The cracks propagate and coalesce with the increasing thermal cycling. The extensive cracking of the rapidly formed non-alumina oxides, resulting from the depletion of aluminum in the bond coat, aids to delamination of the outer ceramic layer. The stress distributions in TGO layer at different thermal shock cycles was measured by luminescence spectroscopy to investigate the failure mechanism of TBC system.

Compacting and sintering of agglomerated ultradispersed powders ZrO2

International Nuclear Information System (INIS)

Galakhov, A.V.; Vyazov, I.V.; Shevchenko, V.Ya.

1989-01-01

Results of investigation into the change of porous structure of shapings of submicron powders under compacting and its effect on the sintering kinetics are presented. ZrO 2 + 3%Y 2 O 3 (molar share) composition powders, produced by coprecipitation from Zr and Y mineral salts are used. Reduction of specific volume of interagglomerated pores is linked with the destruction of large soft agglomerates at the initial compacting shift. At this stage the filling of a part of interagglomerated pores with large agglomerate crushing products takes place. As a result of such a process a part of pores transfers from the class of interagglomerated to the class of intraagglomerated ones increasing their specific content in a compact

Thermal Conductivity and Water Vapor Stability of Ceramic HfO2-Based Coating Materials

Science.gov (United States)

Zhu, Dong-Ming; Fox, Dennis S.; Bansal, Narottam P.; Miller, Robert A.

2004-01-01

HfO2-Y2O3 and La2Zr2O7 are candidate thermal/environmental barrier coating materials for gas turbine ceramic matrix composite (CMC) combustor liner applications because of their relatively low thermal conductivity and high temperature capability. In this paper, thermal conductivity and high temperature phase stability of plasma-sprayed coatings and/or hot-pressed HfO2-5mol%Y2O3, HfO2-15mol%Y2O3 and La2Zr2O7 were evaluated at temperatures up to 1700 C using a steady-state laser heat-flux technique. Sintering behavior of the plasma-sprayed coatings was determined by monitoring the thermal conductivity increases during a 20-hour test period at various temperatures. Durability and failure mechanisms of the HfO2-Y2O3 and La2Zr2O7 coatings on mullite/SiC Hexoloy or CMC substrates were investigated at 1650 C under thermal gradient cyclic conditions. Coating design and testing issues for the 1650 C thermal/environmental barrier coating applications will also be discussed.

Effect of Fe2O3 on the sintering and stabilization of ZrO2-MgO system

International Nuclear Information System (INIS)

Longo, E.; Paskocimas, C.A.; Ambrosecchia, J.R.; Weffort, L.C.; Baldo, J.B.; Leite, L.R.; Varela, J.A.

1990-01-01

Through X-ray diffraction, it was studied the influence of the iron oxide (Fe 2 O 3 ) as a mineralizer in the development of partially stabilized zirconia phases (cubic/tetragonal) within the system ZrO 2 -MgO. In the preparation of the studied compositions it was utilized a Brazilian comercial zirconia powder and different precursors for the MgO and Fe 2 O 3 additives. It was observed that the main effect of iron oxide consisted on the speed up of the solid solution formation process of Mg + 2 in the Zr +4 sub-lattice, as well as being a very effective sintering agent. (author) [pt

Synthesis and physico-chemical characterization of CeO2/ZrO2-SO42- mixed oxides

International Nuclear Information System (INIS)

Hernandez E, J. M.; Silva R, R.; Garcia A, R.; Garcia S, L. A.; Handy, B. E.; Cardenas G, G.; Cueto H, A.

2012-01-01

Environmentally friendly solid-acid catalysts CeO 2 /ZrO 2 -SO 4 2- were prepared by the sol gel method varying CeO 2 content (10, 20 and 30 wt %) and using sulfation in situ, maintaining the sulfate ions amount present in the materials at 20 wt %. ZrO 2 and ZrO 2 -SO 4 2- were also prepared for comparison proposes using the same synthesis method. The materials were characterized by X-ray diffraction, nitrogen physisorption, potentiometric titration with n-butylamine, decomposition of 2-propanol and n-pentane isomerization. The specific surface area of ZrO 2 -SO 4 2- was high (160 m 2 /g) compared with the unmodified ZrO 2 (80 m 2 /g), however this area decreased with increasing the CeO 2 content (37-100 m 2 /g). There was no significant effect of CeO 2 on the tetragonal structure of ZrO 2 -SO 4 2- . The variation of acid sites amount runs parallel to the change of specific surface area. The acid sites amount decreased with increasing cerium oxide content. The decomposition of 2-propanol results fundamentally in the formation of dehydration products such as propylene and diisopropyl ether, both involving acid sites. In addition, a good performance during the n-pentane isomerization was observed for these materials. The selectivity towards isopentane reaches 84% when the Pt/CeO 2 /ZrO 2 -SO 4 2- catalyst with the highest CeO 2 content was used. (Author)

Luminescent properties in films of ZrO2: Dy

International Nuclear Information System (INIS)

Martinez, R. C.; Guzman, J.; Rivera, T.; Ceron, P.; Montes, E.; Guzman, D.; Garcia H, M.; Falcony, C.; Azorin, J.

2014-08-01

In this work the luminescent characterization of zirconium oxide (ZrO 2 ) films impure with dysprosium (Dy +3 ) is reported, obtained by means of the ultrasonics spray pyrolysis technique. The films were deposited on glass substrates (Corning), in a temperatures interval of 400 to 550 grades C, using as precursor elements Zirconium oxide chloride octahydrate (ZrOCl 2 ·8H 2 O) and Dysprosium tri-chloride (DyCl 3 ), dissolved in deionized water, varying the concentration of the contaminated from the 1 to 20 atomic % with relationship to the zirconium in solution. The luminescent characterization was analyzed by means of photoluminescence and thermoluminescence. The photoluminescence results showed a spectrum with three maxima which correspond to the electronic transitions 4 F 9/2 - 6 H 15/2 , 4 F 9/2 - 6 H 13/2 and 4 F 9/2 - 6 H 11/2 characteristics of the Dy 3+ ion. The thermoluminescence (Tl) response when being exposed to a monochrome UV beam in 240 nm showed a wide curve that exhibits a maxim centered in 200 grades C. The Tl response of ZrO 2 :Dy in function of the dose was shown lineal in the interval of 24 mJ/cm 2 to 432 mJ/cm 2 . A study of the repeatability and dissipation of the ZrO 2 :Dy Tl response is included. Considering the shown previous results we can conclude that the ZrO 2 in film form obtained by spray pyrolysis has luminescent properties in 240 nm. (Author)

The charge storage characteristics of ZrO2 nanocrystallite-based charge trap nonvolatile memory

International Nuclear Information System (INIS)

Tang Zhen-Jie; Li Rong; Yin Jiang

2013-01-01

ZrO 2 nanocrystallite-based charge trap flash memory capacitors incorporating a (ZrO 2 ) 0.6 (SiO 2 ) 0.4 pseudobinary high-k oxide film as the charge trapping layer were prepared and investigated. The precipitation reaction in the charge trapping layer, forming ZrO 2 nanocrystallites during rapid thermal annealing, was investigated by transmission electron microscopy and X-ray diffraction. It was observed that a ZrO 2 nanocrystallite-based memory capacitor after post-annealing at 850 °C for 60 s exhibits a maximum memory window of about 6.8 V, good endurance and a low charge loss of ∼25% over a period of 10 years (determined by extrapolating the charge loss curve measured experimentally), even at 85 °C. Such 850 °C-annealed memory capacitors appear to be candidates for future nonvolatile flash memory device applications

Interdiffusion studies on high-Tc superconducting YBa2Cu3O7-δ thin films on Si(111) with a NiSi2/ZrO2 buffer layer

DEFF Research Database (Denmark)

Aarnink, W.A.M.; Blank, D.H.A.; Adelerhof, D.J.

1991-01-01

Interdiffusion studies on high-T(c) superconducting YBa2Cu3O7-delta thin films with thickness in the range of 2000-3000 angstrom, on a Si(111) substrate with a buffer layer have been performed. The buffer layer consists of a 400 angstrom thick epitaxial NiSi2 layer covered with 1200 angstrom...... of polycrystalline ZrO2. YBa2Cu3O7-delta films were prepared using laser ablation. The YBa2Cu3O7-delta films on the Si/NiSi2/ZrO2 substrates are of good quality; their critical temperatures T(c,zero) and T(c,onset) have typical values of 85 and 89 K, respectively. The critical current density j(c) at 77 K equaled 4...... x 10(4) A/cm2. With X-ray analysis (XRD), only c-axis orientation has been observed. The interdiffusion studies, using Rutherford backscattering spectrometry (RBS) and scanning Auger microscopy (SAM) show that the ZrO2 buffer layer prevents severe Si diffusion to the YBa2Cu3O7-delta layer, the Si...

In situ formation of CA6 platelets in Al2O3 and Al2O3/ZrO2 matrices

International Nuclear Information System (INIS)

Belmonte, M.; Sanchez-Herencia, A.J.; Moreno, R.; Miranzo, P.; Moya, J.S.; Tomsia, A.P.

1993-01-01

Al 2 O 3 and Al 2 O 3 /ZrO 2 compacts containing CaO as a dopant have been sintered under different conditions and atmospheres: air, high vacuum (> 10 -6 torr). SEM observations have been made on the polished surfaces of sintered and also of annealed samples. Only after the annealing treatment in air at temperatures ranging from 1400 to 1500 C, a massive formation of CA 6 platelets was detected in samples sintered in low oxygen partial pressure atmospheres. In order to clarify the mechanism of formation of this secondary phase at the grain boundaries, CaO has been introduced in the form of either plaster of Paris (to reproduce a possible contamination provided by the molds in slip casting) or CaCO 3 . The obtained results indicate the important role of the firing atmosphere on the precipitation of secondary phases at grain boundary. (orig.)

The Effect of Acidic and Redox Properties of V2O5/CeO2-ZrO2 Catalysts in Selective Catalytic Reduction of NO by NH3

DEFF Research Database (Denmark)

Putluru, Siva Sankar Reddy; Riisager, Anders; Fehrmann, Rasmus

2009-01-01

V2O5 supported ZrO2 and CeO2–ZrO2 catalysts were prepared and characterized by N2 physisorption, XRPD, TPR, and NH3-TPD methods. The influence of calcination temperature from 400 to 600 °C on crystallinity, acidic and redox properties were studied and compared with the catalytic activity...... in the selective catalytic reduction (SCR) of NO with ammonia. The surface area of the catalysts decreased gradually with increasing calcination temperature. The SCR activity of V2O5/ZrO2 catalysts was found to be related with the support crystallinity, whereas V2O5/CeO2–ZrO2 catalysts were also dependent...... on acidic and redox properties of the catalyst. The V2O5/CeO2–ZrO2 catalysts showed high activity and selectivity for reduction of NO with NH3....

Single-walled carbon nanotube-facilitated dispersion of particulate TiO2 on ZrO2 ceramic membrane filters.

Science.gov (United States)

Yao, Yuan; Li, Gonghu; Gray, Kimberly A; Lueptow, Richard M

2008-07-15

We report that SWCNTs substantially improve the uniformity and coverage of TiO2 coatings on porous ZrO2 ceramic membrane filters. The ZrO2 filters were dip coated with 100 nm anatase TiO2, TiO2/SWCNT composites, a TiO2+SWCNT mixture, and a TiO2/MWCNT composite at pH 3, 5, and 8. Whereas the TiO2+SWCNT mixture and the TiO2/MWCNT composite promote better coverage and less clumping than TiO2 alone, the TiO2/SWCNT composite forms a complete uniform coating without cracking at pH 5 ( approximately 100% coverage). A combination of chemical and electrostatic effects between TiO2 and SWCNTs forming the composite as well as between the composite and the ZrO2 surface explains these observations.

Study of ZrO2-H2SO4-(NH4)2SO4(NH4Cl)-H2O systems

International Nuclear Information System (INIS)

Motov, D.L.; Sozinova, Yu.P.; Rys'kina, M.P.

1988-01-01

Regions of formation, composition and solubility of ammonium sulfatozirconates (ASZ) in ZrO 2 -H 2 SO 4 -(NH 4 ) 2 SO 4 (NH 4 Cl)-H 2 O systems at 25 and 75 deg C are studied by the isothermal method. Five ASZ: (NH 4 ) 2 Zr(OH) 2 (SO 4 ) 2 , NH 4 ZrOH(SO 4 ) 2 xH 2 O, NH 4 ZrO 0.5 (OH) 2 SO 4 x1.5H 2 O, (NH 4 ) 2 Zr(SO 4 ) 3 x2H 2 O, (NH 4 ) 4 Zr(SO 4 ) 4 x4H 2 O are detected, their properties are investigated. Main sulfates are new compounds never described ealier

In situ tritium from Li2O and Li2ZrO3 irradiated in a fast neutron flux: BEATRIX-II, Phase 1 and 2

International Nuclear Information System (INIS)

Slagle, O.D.; Hollenberg, G.W.; Kurasawa, T.; Verrall, R.A.

1994-06-01

BEATRIX-II was an in situ tritium recovery experiment. This in situ tritium recovery experiment provided data on the performance of Li 2 O and Li 2 ZrO 3 under irradiation conditions covering a range of sweep gas compositions and temperatures. The experiment consisted of two separate irradiation cycles which in turn included two vented tritium recovery canisters each. Phase 1 operated for 300 Effective Full Power Days (EFPD) while Phase 2 operated for 203 EFPD of irradiation. The tritium recovery behavior of Li 2 O and Li 2 ZrO 3 was characterized using temperature transients, sweep gas composition changes and reactor power changes to effect changes in the tritium inventory. The high neutron flux level in FFTF resulted in high tritium generation rates which combined with a responsive tritium measurement system allowed detailed observations on the tritium recovery behavior of Li 2 O and Li 2 ZrO 3 . During the course of the experiment a number of observations were made which did not appear consistent with a simplified view of the tritium recovery behavior of these materials. These observations included small negative tritium recovery peaks preceding the typical primary positive peaks; and, for specific temperature ranges, changes in tritium inventory which where opposite to the characteristic expected changes

Characterization of boundary layer thickness of nano fluid ZrO_2 on natural convection process

International Nuclear Information System (INIS)

V-Indriati Sri Wardhani; Henky P Rahardjo

2015-01-01

Cooling system is highly influenced by the process of convection heat transfer from the heat source to the cooling fluid. The cooling fluid usually used conventional fluid such as water. Cooling system performance can be improved by using fluids other than water such as nano fluid that is made from a mixture of water and nano-sized particles. Researchers at BATAN Bandung have made nano fluid ZrO_2 from local materials, as well as experimental equipment for studying the thermohydraulic characteristics of nano fluid as the cooling fluid. In this study, thermohydraulic characteristics of nano fluid ZrO_2 are observed through experimentation. Nano fluid ZrO_2 is made from a mixture of water with ZrO_2 nano-sized particles of 10-7-10-9 nm whose concentration is 1 g/liter. This nano fluid is used as coolant in the cooling process of natural convection. The natural convection process depends on the temperature difference between heat source and the cooling fluid, which occur in the thermal boundary layer. Therefore it is necessary to study the thermal boundary layer thickness of nano fluid ZrO_2, which is also able to determine the local velocity. Experimentations are done with several variation of the heater power and then the temperature are measured at several horizontal points to see the distribution of the temperatures. The temperature distribution measurement results can be used to determine the boundary layer thickness and flow rate. It is obtained that thermal boundary layer thickness and velocity of nano fluid ZrO_2 is not much different from the conventional fluid water. (author)

Effect of ZrO2 on the sintering behavior, strength and high-frequency dielectric properties of electrical ceramic porcelain insulator

Science.gov (United States)

Singh Mehta, Niraj; Sahu, Praveen Kumar; Ershad, Md; Saxena, Vipul; Pyare, Ram; Ranjan Majhi, Manas

2018-01-01

In the present study, the effect of ZrO2 on the sintering, strength and dielectric behavior of electrical ceramic porcelain insulator with substituting alumina content by zirconia (in weight percentage from 0% to 30%) is investigated. The different composition of samples containing different zirconia (ZrO2) contents of 0, 10, 20, and 30 wt% are prepared using the uniaxial pressure technique applying 160 MPa pressure. Further, the prepared samples are also analyzed for sintering temperatures (1350 °C), and effects are observed on mechanical and electric properties of porcelain insulator. Different characterizations such as Dilatometer, x-ray diffraction, scanning electron microscopy and differential thermal analysis/thermo gravimetric analysis were used to evaluate the thermal, phase detection, micro structural and weight loss changes by increasing concentration of ZrO2 on base porcelain composition. At 1350 °C, for the composition having 20 wt% ZrO2 with 10 wt% alumina, the maximum density was observed 2.81 g cm-3 with a porosity of 2.23%. The highest tensile strength of 41 ± 3 MPa is observed for the same sample composition. The minimum value of thermal expansion coefficient is found to be in the range of 10-6 for the sample with 30 wt% ZrO2 content sintered at 1350 °C compared to other prepared samples. Similarly, the highest dielectric value (5.1-4.4) having dielectric loss (0.08-0.12) is achieved for the sample with 30 wt% ZrO2 content sintered at 1350 °C in the frequency range of 4-20 GHz at room temperature. According to the mechanical properties, the composition having 20 wt% ZrO2 on base ceramic porcelain composition has enormous potential to serve as a high strength refractory material. For dielectric properties, the composition having 30 wt% ZrO2 is more suitable for the electrical application.

Mullite and Mullite/ZrO2-7wt.%Y2O3 Powders for Thermal Spraying of Environmental Barrier Coatings

Science.gov (United States)

Garcia, E.; Mesquita-Guimarães, J.; Miranzo, P.; Osendi, M. I.; Wang, Y.; Lima, R. S.; Moreau, C.

2010-01-01

Mullite and mullite/ZrO2-7wt.%Y2O3 coatings could be thought among the main protective layers for environment barrier coatings (EBCs) to protect Si-based substrates in future gas turbine engines. Considering that feedstock of the compound powder is not commercially available, two powder processing routes Spray Drying (SD) and Flame Spheroidization (FS) were implemented for both types of powders. For each method the particle size, the morphology, and microstructure of the powder particles was determined. In addition, the effect of the heat treatment on the powder crystallinity and microstructure of FS powders was also investigated. To evaluate their suitability as feedstock materials, the powders were plasma sprayed and their in-flight particle characteristics monitored for coatings production. The powder morphology was correlated to the in-flight particle characteristics and splat morphology to gain insight about into the influence of powder characteristics on the coating formation.

The new insight into the structure-activity relation of Pd/CeO2-ZrO2-Nd2O3 catalysts by Raman, in situ DRIFTS and XRD Rietveld analysis.

Science.gov (United States)

Yang, X; Yang, L; Lin, J; Zhou, R

2016-01-28

Pd/CeO2-ZrO2-Nd2O3 (CZN) catalysts with different CeO2/ZrO2 molar ratios were synthesized and have been characterized by multiple techniques, e.g. XRD in combination with Rietveld refinement, UV-Raman, XPS and in situ DRIFTS. The XRD pattern of CZN with CeO2/ZrO2 molar ratios ≥1/2 can be indexed satisfactorily to the fluorite structure with a space group Fm3̄m, while the XRD patterns of CZ12 only display diffraction peaks of the tetragonal phase (S.G. P42/nmc). Nd addition can effectively stabilize the cubic structure of the CZN support and increase the enrichment of defect sites on the surface, which may be related to the better catalytic activity of Pd/CZN12 catalysts compared with Pd/CZ12. The presence of moderate ZrO2 can increase the concentration of O* active species, leading to accelerate the formation of nitrate species and thus enhance the catalytic activity of NOx and HC elimination. The Pd-dispersion decreases with the increasing Zr content, leading to the decreased CO catalytic activity, especially for the aged catalysts. The change regularity of the OSC value is almost the same with the in situ dynamic operational window, demonstrating that the in situ dynamic operational window is basically affected by the OSC value.

Synthesis and thermoluminescence behavior of ZrO2:Eu3+ with variable concentration of Eu3+ doped phosphor

Directory of Open Access Journals (Sweden)

Raunak Kumar Tamrakar

2014-10-01

Full Text Available Cubical ZrO2 phosphor doped with the europium synthesized by conventional solid state synthesis method. The prepared phosphor was characterized by X-ray diffraction (XRD technique, field emission gun scanning electron microscopy (FEGSEM and transmission electron microscopy (TEM. In this paper, we focused on the thermoluminescence glow curves and kinetic parameters, activation energy, order of kinetics, and the frequency factor of ZrO2:Eu3+ phosphor under different doses of UV irradiations at a heating rate of 6.7 °C/s. The kinetic parameters activation energy E, the order of kinetics b, and the frequency factor s of synthesized phosphor of ZrO2:Eu3+ have been calculated by using a peak shape method.

Microestructura de Al2O3/TZP codopado con Fe2O3 y TiO2 fabricado por reacción (RBAO

Directory of Open Access Journals (Sweden)

Jiménez, M.

2003-02-01

Full Text Available Reaction-bonded 80 vol% Al2O3/TZP (2 mol% Y2O3-stabilized tetragonal zirconia polycrystals composites co-doped with 1 vol% Fe2O3 and 1 vol% TiO2 have been produced, and then presureless sintered (1450 ºC, 60 min or sinter-forged (20 MPa, 1200 ºC, 60 min. The resulting microstructures have been characterized using scanning electron microscopy. Both types of materials are dense, with a fine and homogeneous dual microstructure consisting of Al2O3 and TZP grains without intermediate grain boundary phases. Sinter-forged composites exhibit a very narrow pore size distribution, essentially smaller than the grain size of the alumina and zirconia phases. Co-doping promotes the sintering of alumina at lower temperatures, while still retains a fine grain size due to the presence of the dispersed zirconia phase. First results on presureless sintered RBAO materials show a fracture strength higher than in conventionally sintered and sinter-forged composites.Se han fabricado compuestos de 80% vol. Al2O3/TZP (ZrO2 estabilizada con 2% mol Y2O3 codopados con 1% vol. Fe2O3 y 1% vol. TiO2 mediante la tecnología RBAO (“Reaction Bonding of Aluminum Oxide”, que se han sinterizado libremente (1450 ºC, 60 min y bajo carga uniaxial (20 MPa, 1200 ºC, 60 min. Se ha caracterizado la microestructura mediante microscopía electrónica de barrido. Ambos materiales son densos con una microestructura homogénea formada por granos de alúmina y de circona, sin fases en juntas de grano. En el caso de la sinterización bajo carga, la distribución del tamaño de los poros es muy estrecha, y esencialmente menor que las correspondientes a los granos de Al2O3 y TZP. El codopado promueve la sinterización de la alúmina, mientras que los granos dispersos de circona inhiben su crecimiento de grano. Los ensayos preliminares de flexión en cuatro puntos realizados sobre los materiales sinterizados sin carga indican una resistencia a la fractura superior a la que presentan los

Thermal evolution of CaO-doped HfO{sub 2} films and powders

Energy Technology Data Exchange (ETDEWEB)

Barolin, S A; Sanctis, O A de [Lab. Materiales Ceramicos, FCEIyA, Universidad Nacional de Rosario, IFIR-CONICET (Argentina); Caracoche, M C; Martinez, J A; Taylor, M A; Pasquevich, A F [Departamento de Fisica, FCE, Universidad Nacional de La Plata, IFLP-CONICET (Argentina); Rivas, P C, E-mail: oski@fceia.unr.edu.a [Facultad de Ciencias Agronomicas y Forestales, Universidad Nacional de La Plata, IFLP (Argentina)

2009-05-01

Solid solutions of ZrO2 and HfO2 are potential electrolyte materials for intermediate-temperature SOFC because both are oxygen-ion conductors. The main challenge for these compounds is to reduce the relatively high value of the activation energies vacancies diffusion, which is influenced by several factors. In this work the thermal evolution of CaO-HfO{sub 2} materials have been investigated. (CaO)y-Hf(1-y)O(2-y) (y = 0.06, 0.14 y 0.2) coatings and powders were synthesized by chemical solution deposition (CSD). Films were deposited onto alumina substrates by Dip Coating technique, the burning of organic waste was carried out at 500 deg. C under normal atmosphere and then the films were thermally treated at intervals of temperature rising to a maximum temperature of 1250 deg. C. By means Glazing Incidence X-ray Diffraction (rho-2theta configuration) the phases were studied in the annealed films. On the other hand, the thermal evolution and crystallization process of powders were analyzed in-situ by HT-XRD. The phenomena crystallization occurred in films and powders were analyzed. The activation energies of diffusion of oxygen vacancies of HfO2-14 mole% CaO and HfO2-20 mole% CaO films were measured from the thermal evolution of the relaxation constant measured by Perturbed Angular Correlation Technique.

Effect of titanium and calcium oxide additions on Zr2O2 polymorphism during Al2O3+Zr2O2 mixture fusion

International Nuclear Information System (INIS)

Gladkov, V.E.; Zhekhanova, N.B.; Fotiev, A.A.; Viktorov, V.V.; Ivashinnikov, V.T.; Zubov, A.S.

1985-01-01

The effect of titanium and calcium containing additions introduced into the Al 2 O 3 +ZrO 2 melt on the phase composition and temperature ranges of ZrO 2 polymorphous transformation in the material is investigated. It is shown that introducing sponge titanium into the 70Al 2 O 3 +30ZrO 2 prepared composition melt (mass. %) with its subsequent intensive cooling one can conserve upto room temperatures 50-70% of ZrO 2 metastable tetragonal modification and therefore reduce the volume changes causing metal cracking. Calcium oxide doping stabilizes the ZrO 2 cubic modification and reduces α-Al 2 O 3 content due to formation of aluminates

ZrO2TETRAGONAL OBTENIDO POR EL MÉTODO DE PRECIPITACIÓN CONTROLADA

OpenAIRE

CAMPO CEBALLOS, DIEGO A.; RODRIGUEZ PÁEZ, JORGE E.

2011-01-01

En este trabajo se utilizó el método de precipitación controlada para sintetizar ZrO2 tetragonal estabilizado con óxido de calcio, CaO. Los sólidos obtenidos se caracterizaron utilizando análisis térmico diferencial y gravimétrico (ATD/TG), Espectroscopia Infrarroja con transformada rápida de Fourier (FT-IR), Difracción de Rayos X (DRX), y microscopia electrónica de transmisión (MET). Los resultados indican que al tratar el polvo cerámico a una temperatura de 600 ºC se obtiene ZrO2 con fase c...

Hydrogenation/Deoxygenation (H/D Reaction of Furfural-Acetone Condensation Product using Ni/Al2O3-ZrO2 Catalyst

Directory of Open Access Journals (Sweden)

Adam Mahfud

2016-08-01

Full Text Available The catalytic hydrogenation/deoxygenation (H/D reaction was carried out using Ni/Al2O3-ZrO2 catalyst. The 10% (wt/wt of Ni were impregnated on Al2O3-ZrO2 (10NiAZ by wet impregnation method followed by calcination and reduction. X-Ray diffraction analysis showed that Nideposited on the surface, with specific surface areas (SBET was 48.616 m2/g. Catalyst performance were evaluated for H/D reaction over furfural-acetone condensation products, mixture of 2-(4-furyl-3-buten-2-on and 1,5-bis-(furan-2-yl-pentan-3-one. The reaction was carried out in a batch, performed at 150°C for 8 hours. The H/D reaction gave alkane derivatives C8 and C10 by hydrogenation process followed by ring opening of furan in 15.2% yield. While, oxygenated product C10-C13 were also detected in 17.2% yield. The increasing of pore volume of 10NiAZ might enhance catalyst activity over H/D reaction. The alkene C=C bond was easy to hydrogenated under this condition by the lower bond energy gap.

Mass spectroscopy of recoiled ions, secondary ion mass spectroscopy, and Auger electron spectroscopy investigation of Y2O3-stabilized ZrO2(100) and (110)

International Nuclear Information System (INIS)

Herman, G.S.; Henderson, M.A.; Starkweather, K.A.; McDaniel, E.P.

1999-01-01

We have studied the (100) and (110) surfaces of yttria-stabilized cubic ZrO 2 using Auger electron spectroscopy, low energy electron diffraction (LEED), direct recoil spectroscopy, mass spectroscopy of recoiled ions (MSRI), and secondary ion mass spectroscopy (SIMS). The concentration of yttrium at the surface was weakly influenced by the surface structure under the experimental conditions investigated. Both MSRI and SIMS indicated a more enhanced yttrium signal than zirconium signal at the surface compared to the respective bulk concentrations. The surfaces were not very well ordered as indicated by LEED. The yttria-stabilized cubic ZrO 2 single crystal surfaces may not be a suitable model material for pure phase ZrO 2 surfaces due to significant yttria concentrations at the surface. copyright 1999 American Vacuum Society

Simulation study of negative thermal expansion in yttrium tungstate Y2W3O12.

Science.gov (United States)

Rimmer, Leila H N; Dove, Martin T

2015-05-13

A simulation study of negative thermal expansion in Y2W3O12 was carried out using calculations of phonon dispersion curves through the application of density functional perturbation theory. The mode eigenvectors were mapped onto flexibility models and results compared with calculations of the mode Grüneisen parameters. It was found that many lower-frequency phonons contribute to negative thermal expansion in Y2W3O12, all of which can be described in terms of rotations of effectively rigid WO4 tetrahedra and Y-O rods. The results are strikingly different from previous phonon studies of higher-symmetry materials that show negative thermal expansion.

Yb:Y2O3 transparent ceramics processed with hot isostatic pressing

Science.gov (United States)

Wang, Jun; Ma, Jie; Zhang, Jian; Liu, Peng; Luo, Dewei; Yin, Danlei; Tang, Dingyuan; Kong, Ling Bing

2017-09-01

Highly transparent 5 at.% Yb:Y2O3 ceramics were fabricated by using a combination method of vacuum sintering and hot isostatic pressing (HIP). Co-precipitated Yb:Y2O3 powders, with 1 at.% ZrO2 as the sintering aid, were used as the starting material. The Yb:Y2O3 ceramics, vacuum sintered at 1700 °C for 2 h and HIPed at 1775 °C for 4 h, exhibited small grain size of 1.9 μm and highly dense microstructure. In-line optical transmittance of the ceramics reached 83.4% and 78.9% at 2000 and 600 nm, respectively. As the ceramic slab was pumped by a fiber-coupled laser diode at about 940 nm, a maximum output power of 0.77 W at 1076 nm was achieved, with a corresponding slope efficiency of 10.6%.

The Composition of Intermediate Products of the Thermal Decomposition of (NH4)2ZrF6 to ZrO2 from Vibrational-Spectroscopy Data

Science.gov (United States)

Voit, E. I.; Didenko, N. A.; Gaivoronskaya, K. A.

2018-03-01

Thermal decomposition of (NH4)2ZrF6 resulting in ZrO2 formation within the temperature range of 20°-750°C has been investigated by means of thermal and X-ray diffraction analysis and IR and Raman spectroscopy. It has been established that thermolysis proceeds in six stages. The vibrational-spectroscopy data for the intermediate products of thermal decomposition have been obtained, systematized, and summarized.

Bioactivity and cell proliferation in radiopaque gel-derived CaO-P2O5-SiO2-ZrO2 glass and glass-ceramic powders.

Science.gov (United States)

Montazerian, Maziar; Yekta, Bijan Eftekhari; Marghussian, Vahak Kaspari; Bellani, Caroline Faria; Siqueira, Renato Luiz; Zanotto, Edgar Dutra

2015-10-01

In this study, 10 mol% ZrO2 was added to a 27CaO-5P2O5-68SiO2 (mol%) base composition synthesized via a simple sol-gel method. This composition is similar to that of a frequently investigated bioactive gel-glass. The effects of ZrO2 on the in vitro bioactivity and MG-63 cell proliferation of the glass and its derivative polycrystalline (glass-ceramic) powder were investigated. The samples were characterized using thermo-gravimetric and differential thermal analysis (TG/DTA), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM) coupled to energy dispersive X-ray spectroscopy (EDS). Release of Si, Ca, P and Zr into simulated body fluid (SBF) was determined by inductively coupled plasma (ICP). Upon heat treatment at 1000 °C, the glass powder crystallized into an apatite-wollastonite-zirconia glass-ceramic powder. Hydroxycarbonate apatite (HCA) formation on the surface of the glass and glass-ceramic particles containing ZrO2 was confirmed by FTIR and SEM. Addition of ZrO2 to the base glass composition decreased the rate of HCA formation in vitro from one day to three days, and hence, ZrO2 could be employed to control the rate of apatite formation. However, the rate of HCA formation on the glass-ceramic powder containing ZrO2 crystal was equal to that in the base glassy powder. Tests with a cultured human osteoblast-like MG-63 cells revealed that the glass and glass-ceramic materials stimulated cell proliferation, indicating that they are biocompatible and are not cytotoxic in vitro. Moreover, zirconia clearly increased osteoblast proliferation over that of the Zr-free samples. This increase is likely associated with the lower solubility of these samples and, consequently, a smaller variation in the media pH. Despite the low solubility of these materials, bioactivity was maintained, indicating that these glassy and polycrystalline powders are potential candidates for bone graft substitutes and bone cements with

Li_2ZrO_3-coated Li_4Ti_5O_1_2 with nanoscale interface for high performance lithium-ion batteries

International Nuclear Information System (INIS)

Zhang, Han; Liu, Yang; Wang, Ting; Yang, Yang; Shi, Shaojun; Yang, Gang

2016-01-01

Graphical abstract: - Highlights: • Zr doped and Li_2ZrO_3 coated Li_4Ti_5O_1_2 are prepared by a solid-state method. • Zr-doping and LZO coating are positive in improving lithium diffusion ability. • Li_2ZrO_3 coated Li_4Ti_5O_1_2 deliver 168.1 mAh g"−"1 higher than 150.2 mAh g"−"1 of Li_4Ti_5O_1_2. • Li_2ZrO_3 coated Li_4Ti_5O_1_2 remains 162 mAh g"−"1 after 100 cycles. • The lowest D_L_i"+ is 5.97 × 10"−"1"7 and 1.85 × 10"−"1"5 cm"2 s"−"1 of Li_4Ti_5O_1_2 before and after coating. - Abstract: Zr doped sample of Li_4Ti_4_._9_9Zr_0_._0_1O_1_2 (LZTO) and Li_2ZrO_3 (LZO) coated Li_4Ti_5O_1_2 (LTO) are prepared by a solid-state method. The lattice structure of LTO is remained after doping element of Zr and coating layer of LZO. The crystal structure and electrochemical performance of the material are investigated by X-ray diffractometry (XRD), high-resolution transmission electron microscopy (HRTEM), cyclic voltammetry (CV), galvanostatic intermittent titration technique (GITT) and charge-discharge tests, respectively. Zr-doping and LZO coating play the positive role in improving the diffusion ability of lithium cations. LZTO and LZO-LTO show much improved specific capacity and rate capability compared with pristine sample of LTO. LZO-LTO has the smallest voltage differential (ΔV) of the redox peaks because the coating of Li_2ZrO_3 is helpful for the diffusion ability of lithium ions during charge/discharge processes. LZTO and LZO-LTO as electrode deliver the initial capacities of 164.8, 168.1 mAh g"−"1, respectively, which are much higher than 150.2 mAh g"−"1 of intrinsic sample of LTO. Even at the current density of 2 A g"−"1, LTZO and LZO-LTO offer capacity of 96 and 106 mAh g"−"1, which are much higher than 33 mAh g"−"1 of LTO. The improved electrochemical performance is attributed to the improved diffusion ability of lithium. During the whole discharge process, the lowest value of LTO is 5.97 × 10"−"1"7 cm"2 s"−"1 that is

A Feasibility Study on UO2/ZrO2 Mixture Melting using Induction Skull Melting Method

International Nuclear Information System (INIS)

Hong, S. W.; Kim, J. H.; Kim, H. D.

1998-01-01

Using ISM(Induction Skull Melting) method, which is usually used for the crystallization of refractory materials, a feasibility study on melting of the UO 2 /ZrO 2 mixture(w/o 8:2) is carried out. Frequency, one of main design parameters for ISM, is determined from electrical resistance of UO 2 /ZrO 2 mixture. Heat loss from the crucible for UO 2 /ZrO 2 20kg melting is predicted by comparison with the existing experimental data for UO , ZrO 2 , and ThO 2 . The analysis shows that melting and superheating of the UO 2 /ZrO 2 mixture using induction skull melting method is possible. To attain the superheat of 300K for 20 kg of UO 2 /ZrO 2 , 100kHz, 100 kW power input for induction coil, and 570L/min coolant flow rate are found to be required. The results of this feasibility study will be adopted for designing UO 2 /ZrO 2 furnace using actual corium material at KAERI

Atomistic studies of cation transport in tetragonal ZrO2 during zirconium corrosion

International Nuclear Information System (INIS)

Bai, Xian-Ming; Zhang, Yongfeng; Tonks, Michael R.

2015-01-01

Zirconium alloys are the major fuel cladding materials in current reactors. The water-side corrosion is a significant degradation mechanism of these alloys. During corrosion, the transport of oxidizing species in zirconium dioxide (ZrO 2 ) determines the corrosion kinetics. Previously, it has been argued that the outward diffusion of cations is important for forming protective oxides. In this work, the migration of Zr defects in tetragonal ZrO 2 is studied with temperature accelerated dynamics and molecular dynamics simulations. The results show that Zr interstitials have anisotropic diffusion and migrate preferentially along the [001] or c direction in tetragonal ZrO 2 . The compressive stresses can increase the Zr interstitial migration barrier significantly. The migration of Zr interstitials at a grain boundary is much slower than in a bulk oxide. The implications of these atomistic simulation results in the Zr corrosion are discussed. (authors)

Densification and mechanical properties of ZrO2-CaAl4O7 composites obtained by reaction sintering

International Nuclear Information System (INIS)

Bruni, Yesica; Aglietti, Esteban

2016-01-01

Composites of the ZrO 2 -CaO-Al 2 O 3 system exhibit high corrosion resistance and high chemical stability, these being suitable properties for enhanced performance as refractories. In this work composites based on ZrO 2 -CaAl 4 O 7 (CA 2 ) were developed by reaction sintering of two pure ZrO 2 powders with different particle size (d 50 = 0.44 μm and d 50 = 8 μm) mixed with high-alumina cement. The effects of CaO to ZrO 2 molar ratio, particle size of ZrO 2 and sintering temperature on densification, c-ZrO 2 formation, microstructure and mechanical properties (Vickers hardness, dynamic Young's modulus and compressive strength) were determined. Porosity and mean pore size of composites reduced with decreasing both particle size of ZrO 2 and CaO content. The highest compression strength of ∝350 MPa and hardness of 6 GPa corresponded to dense ZrO 2 -based composite with 15 vol.% CA 2 sintered at 1400 C.

Luminescence and energy transfer properties of Eu3+ and Gd3+ in ZrO2

International Nuclear Information System (INIS)

Villabona-Leal, E.G.; Diaz-Torres, L.A.; Desirena, H.; Rodríguez-López, J.L.; Pérez, Elías; Meza, Octavio

2014-01-01

Red luminescence emission in ZrO2:Gd 3+ –Eu 3+ nanocrystal under 250 nm radiation excitation is achieved. These materials exhibit a tetragonal phase that is retained by the presence of lanthanide ions. Thus, a study of the optical properties as a function of the dopant concentration was been carried out without the deleterious effects of having segregation of other crystalline phases. We analyze the emission and lifetime curves as a function of dopant concentration through a rate equation simulation, finding an excellent fitting. As results, the nonradiative and radiative relaxation constants, as well as a quantitative estimation of the energy transfer processes among Eu 3+ , Gd 3+ and O 2− ions are reported for the first time. The proposed model can be extended (or applicable) to explain the fluorescence dynamics in other nanomaterials doped with Eu 3+ and Gd 3+ under UV excitation. -- Highlights: • ZrO 2 nanocrystal exhibits a tetragonal phase in the presence of Eu and Gd dopants. • Emission and lifetimes as a function of dopant concentration were analyzed by rate equation model. • Quantitative estimation of the energy transfer processes among Eu 3+ , Gd 3+ and O 2− ions are reported

MoO3/SiO2-ZrO2 Catalyst: Eeffect of Calcination Temperature on Physico-chemical Properties and Activities in Nitration of Toluene

Directory of Open Access Journals (Sweden)

Sunil Madhavrao Kemdeo

2012-12-01

Full Text Available 12 wt % molybdena was deposited over 1:1 silica zirconia mixed oxide support and the resultant catalyst was calcined between the 500 to 700 oC range of temperature. The samples were characterized by XRD, FT-IR, BET, SEM, NH3-TPD and pyridine adsorbed FT-IR techniques.  Nitration of toluene was studied as a model reaction over the prepared catalysts and parameters like effect of reaction temperature, effect of various solvents, catalyst reusability are studied. It was found that conversion of toluene varies with the presence of Brönsted acid sites over the catalyst surface and para-nitrotoulene selectivity is associated with pore size of the catalyst. Over the same catalysts, nitration was extended for some other aromatics. Avoid of sulfuric acid in the present process is an interesting concern in view of green chemistry. Copyright © 2012 by BCREC UNDIP. All rights reservedKeywords: MoO3/SiO2-ZrO2; SO2-ZrO2; NH3-TPD; Nitration; ortho-nitro tolueneReceived: 19th May 2012, Revised: 24th May 2012, Accepted: 26th May 2012[How to Cite: S.M. Kemdeo. (2012. MoO3/SiO2-ZrO2 Catalyst: Effect of Calcination Temperature on Physico-chemical Properties and Activities in Nitration of Toluene. Bulletin of Chemical Reaction Engineering & Catalysis, 7 (2: 92-104. doi:10.9767/bcrec.7.2.3521.92-104] [How to Link / DOI: http://dx.doi.org/10.9767/bcrec.7.2.3521.92-104 || or local: http://ejournal.undip.ac.id/index.php/bcrec/article/view/3521] | View in 

The Development of HfO2-Rare Earth Based Oxide Materials and Barrier Coatings for Thermal Protection Systems

Science.gov (United States)

Zhu, Dongming; Harder, Bryan James

2014-01-01

Advanced hafnia-rare earth oxides, rare earth aluminates and silicates have been developed for thermal environmental barrier systems for aerospace propulsion engine and thermal protection applications. The high temperature stability, low thermal conductivity, excellent oxidation resistance and mechanical properties of these oxide material systems make them attractive and potentially viable for thermal protection systems. This paper will focus on the development of the high performance and high temperature capable ZrO2HfO2-rare earth based alloy and compound oxide materials, processed as protective coating systems using state-or-the-art processing techniques. The emphasis has been in particular placed on assessing their temperature capability, stability and suitability for advanced space vehicle entry thermal protection systems. Fundamental thermophysical and thermomechanical properties of the material systems have been investigated at high temperatures. Laser high-heat-flux testing has also been developed to validate the material systems, and demonstrating durability under space entry high heat flux conditions.

The detailed orbital-decomposed electronic structures of tetragonal ZrO2

International Nuclear Information System (INIS)

Zhang, Yan; Ji, Vincent; Xu, Ke-Wei

2013-01-01

The detailed orbital-decomposed electronic structures of the tetragonal zirconia have been investigated by using the first-principles projector augmented wave (PAW) potential within the generalized gradient approximation (GGA) as well as taking into account the on-site Coulomb repulsive interaction (GGA+U). The deviation of the minimization energy from d z =0 to d z =±0.032 for experimental lattice constants (a=3.605 Å and c=5.180 Å) confirms the alternating displacement of the oxygen atoms, which causes half of the Zr---O bonds stronger and the other half weaker compared with the bonds in symmetric (d z =0) zirconia. The distorted tetragonal environment of the eight oxygen anions around Zr site splits the five-fold degenerate d states of a free Zr atom into triply degenerate t 2g (d xy , d yz and d zx ) states and doubly degenerate e g (d z 2 and d x 2 -y 2 ) states. The additional covalent character upon Zr-O ionic bonds are resulted from the hybridization between the O(2s), O(2p) and Zr(5s), triply degenerate t 2g (d xy , d yz and d zx ) states of Zr(4d). The O(2s) and O(2p) states are clearly separated and no hybrid bonding states are formed

Extremely fine structured cathode for solid oxide fuel cells using Sr-doped LaMnO3 and Y2O3-stabilized ZrO2 nano-composite powder synthesized by spray pyrolysis

Science.gov (United States)

Shimada, Hiroyuki; Yamaguchi, Toshiaki; Sumi, Hirofumi; Nomura, Katsuhiro; Yamaguchi, Yuki; Fujishiro, Yoshinobu

2017-02-01

A solid oxide fuel cell (SOFC) for high power density operation was developed with a microstructure-controlled cathode using a nano-composite powder of Sr-doped LaMnO3 (LSM) and Y2O3-stabilized ZrO2 (YSZ) synthesized by spray pyrolysis. The individual LSM-YSZ nano-composite particles, formed by crystalline and amorphous nano-size LSM and YSZ particles, showed spherical morphology with uniform particle size. The use of this powder for cathode material led to an extremely fine microstructure, in which all the LSM and YSZ grains (approximately 100-200 nm) were highly dispersed and formed their own network structures. This microstructure was due to the two phase electrode structure control using the powder, namely, nano-order level in each particle and micro-order level between particles. An anode-supported SOFC with the LSM-YSZ cathode using humidified H2 as fuel and ambient air as oxidant exhibited high power densities, such as 1.29 W cm-2 under a voltage of 0.75 V and a maximum power density of 2.65 W cm-2 at 800 °C. Also, the SOFC could be stably operated for 250 h with no degradation, even at a high temperature of 800 °C.

Growth of TiO2-ZrO2 Binary Oxide Electrode for Dye Sensitized Solar Cell Application

International Nuclear Information System (INIS)

Than Than Win; Aye Myint Myat Kywe; Shwe Yee Win; Honey Thaw; Yin Maung Maung; Ko Ko Kyaw Soe

2011-12-01

TiO2-ZrO2 fine binary oxide was prepared by mechanochemical milling process to be homogeneous binary oxide powder. TiO2-ZrO2 paste was deposited on microscopic glass slide by rolling. It was immersed in the henna solution and annealed at 100C for 2h. It was deposited onto another glass slide and used as counter electrode (second electrode). Two glass slides were offset and two binder clips were used to hold the electrodes together. Photovoltaic properties of TiO2-ZrO2 cell were measured and it was expected to utilize the dye sensitized solar cells application.

Tritium inventory in Li2ZrO3 blanket

International Nuclear Information System (INIS)

Nishikawa, M.; Baba, A.

1998-01-01

Recently, we have presented the way to estimate the tritium inventory in a solid breeder blanket considering effects of diffusion of tritium in the grain, absorption of water in the bulk of grain, and adsorption of water on the surface of grain, together with two types of isotope exchange reactions. It is reported in our previous paper that the estimated tritium inventory for a LiAlO 2 blanket agrees well with data observed in various in situ experiments when the effective diffusivity of tritium from the EXOTIC-6 experiment is used and that the better agreement is obtained when existence of some water vapor is assumed in the purge gas. The same way as used for a LiAlO 2 blanket is applied to a Li 2 ZrO 3 blanket in this study and the estimated tritium inventory shows a good agreement with data obtained in such in situ experiments as MOZART, EXOTIC-6 and TRINE experiments. (orig.)

Reduced cobalt phases of ZrO2 and Ru/ZrO2 promoted cobalt catalysts and product distributions from Fischer–Tropsch synthesis

International Nuclear Information System (INIS)

Kangvansura, Praewpilin; Schulz, Hans; Suramitr, Anwaraporn; Poo-arporn, Yingyot; Viravathana, Pinsuda; Worayingyong, Attera

2014-01-01

Highlights: • Ru/ZrO 2 , ZrO 2 promoted Co/SiO 2 for FTS were reduced by time resolved XANES. • Reduced catalysts resulted from XANES reduction showed the mixed phases of Co, CoO. • The highest percentages of CoO resulted from the high ZrO 2 promoted Co/SiO 2 . • Product distributions of 1-alkenes, iso-alkanes indicated sites for FTS and the 2° reaction. • Alkene readsorption were high corresponding to the high CoO forming branched alkanes. - Abstract: Co/SiO 2 catalysts were promoted with 4% and 8% ZrO 2 . Small amounts (0.07%) of Ru were impregnated onto 4%ZrO 2 /Co/SiO 2 . Catalysts resulting from time-resolved XANES reduction showed mixed phases of Co and CoO, with the highest percentages of Co resulting from Ru/4%ZrO 2 /Co/SiO 2 and the highest percentages of CoO resulting from 8%ZrO 2 /Co/SiO 2 . Product distributions of n-alkanes, iso-alkanes and alkenes during Fischer–Tropsch Synthesis (FTS) were used to investigate the catalyst performance of 4%ZrO 2 /Co/SiO 2 8%ZrO 2 /Co/SiO 2 and Ru/4%ZrO 2 /Co/SiO 2 . FTS steady state was studied by growth probabilities of n-alkane products. No 1-alkene was produced from Ru/4%ZrO 2 /Co/SiO 2 , indicating high availability of Fischer–Tropsch sites for long chain hydrocarbon growth, despite high methanation. Branched alkanes produced from the secondary reaction were related to the high CoO percentages on 8%ZrO 2 /Co/SiO 2 . Alkene readsorption sites were high, corresponding to the high CoO percentages, causing a high probability of forming branched alkane products

Efficient photoluminescence of Dy3+ at low concentrations in nanocrystalline ZrO2

International Nuclear Information System (INIS)

Diaz-Torres, L.A.; Rosa, E. de la; Salas, P.; Romero, V.H.; Angeles-Chavez, C.

2008-01-01

Nanocrystalline ZrO 2 :Dy 3+ were prepared by sol-gel and the structural and photoluminescence properties characterized. The crystallite size ranges from 20 to 50 nm and the crystalline phase is a mixture of tetragonal and monoclinic structure controlled by dopant concentration. Strong white light produced by the host emission band centered at ∼460 nm and two strong Dy 3+ emission bands, blue (488 nm) and yellow (580 nm), under direct excitation at 350 nm were observed. The highest efficiency was obtained for 0.5 mol% of Dy 3+ . Emission is explained in terms of high asymmetry of the host suggesting that Dy 3+ are substituted mainly into Zr 4+ lattice sites at the crystallite surface. Luminescence quenching is explained in terms of cross-relaxation of intermediate Dy 3+ levels. - Graphical abstract: White light emission from ∼70 nm ZrO 2 :Dy 3+ nanocrystals. The highest efficiency was obtained for 0.5 mol% of dopant and the dominant crystalline structure was monoclinic

Phase relations in crystalline ceramic nuclear waste forms the system UO/sub 2 + x/-CeO2-ZrO2-ThO2 at 12000C in air

International Nuclear Information System (INIS)

Pepin, J.G.; McCarthy, G.J.

1981-01-01

Steady-state phase relations in the system UO/sub 2 + x/-CeO 2 -ZrO 2 -ThO 2 were determined for application to phase relations in the high-level crystalline ceramic nuclear waste form Supercalcine-Ceramics. Samples were treated at 1200 0 C at an oxygen partial pressure of 0.21 atm and a total pressure of 1 atm. Phase assemblages were found to be composed of cubic solid solutions of the flourite structure type, solid solutions based on ZrO 2 , and orthorhombic solid solutions based on U 3 O 8

Color and vanadium valency in V-doped ZrO2

International Nuclear Information System (INIS)

Ren, Feng; Ishida, Shingo; Takeuchi, Nobuyuki

1993-01-01

The distribution and chemical states of vanadium in V-doped ZrO 2 were studied to clarify the origin of the color of vanadium-zirconium yellow pigment in comparison with vanadium-tin yellow pigment. ESCA data and measurements of lattice constants of V-doped ZrO 2 revealed that vanadium was dissolved mainly as V 4+ substituting for Zr in ZrO 2 lattice, and its solubility limit was 0.5 wt% as V 2 O 5 . It was found that the yellow color of vanadium-zirconium yellow was produced predominantly by the dissolved vanadium and that the contribution of vanadium oxide on ZrO 2 grains to the yellow color was about 1.30 of that of the dissolved vanadium when compared on the basis of equimolar quantity of vanadium. Most of the undissolved vanadium oxide was in an amorphous or a poorly crystallized state

Thermoluminescent dosimetry of ionizing radiations using ZrO2 prepared at low temperatures

International Nuclear Information System (INIS)

Rivera M, T.; Diaz G, J.A.I.; Olvera T, L.; Azorin N, J.; Barrera S, M.; Soto E, A.M.

2005-01-01

The thermoluminescent dosimetry (TLD) it is a versatile tool for an evaluation of dose of ionizing radiation. A great variety of ceramic materials and their different physical forms allow a determination of the ionizing radiation in a wide dose interval. In this work the results of studying those thermoluminescent characteristics (TL) of the zirconium oxide obtained by means of the sol-gel technique to low temperatures are presented. To these temperatures the material was obtained in its amorphous state (ZrO 2 -a). The structural characteristics of ZrO 2 -a they were obtained by means of X-ray diffraction. The TL characteristics studied were: TL curve, reproducibility of the TL signal and the fading of the information. The powders of ZrO 2 -a, previously irradiated with beta particles of 90 Sr/ 90 Y, they presented a thermoluminescent curve with two peaks at 150 and 260 C. The fading of the information of the one ZrO 2 -a it was of 20% during the first two hours starting from this time there was one lost of information of 5% to the finish of the 30 days. The reproducibility of the information was of ± 2.5% in standard deviation. (Author)

High electron beam dosimetry using ZrO2

International Nuclear Information System (INIS)

Lueza M, F.; Rivera M, T.; Azorin N, J.; Garcia H, M.

2009-10-01

This paper reports the experimental results of studying the thermoluminescent (Tl) properties of ZrO 2 powder embedded in polytetrafluorethylene (PTFE) exposed to high energy electron beam from linear accelerators (Linac). Structural and morphological characteristics were also reported. Irradiations were conducted using high energy electrons beams in the range from 2 to 18 MeV. Pellets of ZrO 2 +PTFE were produced using polycrystalline powder grown by the precipitation method. These pellets presented a Tl glow curve exhibiting an intense glow peak centered at around 235 C. Tl response as a function of high electron absorbed dose was linear in the range from 2 to 30 Gy. Repeatability determined by exposing a set of pellets repeatedly to the same electron absorbed dose was 0.5%. Fading along 30 days was about 50%. Then, results obtained in this study suggest than ZrO 2 +PTFE pellets could be used for high energy electron beam dosimetry provided fading correction is accounted for. (Author)

Zirconia stabilization and its retention at room temperature in the ZrO sub(2). TiO sub(2) system. Estabilizacao de zirconia e sua retencao a temperatura ambiente no sistema ZrO sub(2). TiO sub(2)

Energy Technology Data Exchange (ETDEWEB)

Pandolfelli, V C; Rodrigues, J A [Sao Carlos Univ., SP (Brazil). Dept. de Engenharia de Materiais; Longo, E [Sao Carlos Univ., SP (Brazil). Dept. de Quimica; Stevens, R [Leeds Univ. (UK)

1990-01-01

Based on the results obtained in the ZrO sub(2).MO sub(x) systems, the stabilization aspects of tetragonal zirconia is discussed in an integrated way, in order to differentiate among the thermodynamical, the kinetic and stress fields effects of the dopant ion on the stabilization. In the ZrO2.TiO2 system, when in solid solution, TiO additions act to suppress the ZrO2 densification, leading to grain growth when attempts are made to attain higher densities. Such effect is believed to be the main factor preventing retention of tetragonal zirconia at room temperature in this system. (author).

X ray photoelectron spectroscopy (XPS) analysis of Photosensitive ZrO2 array

Science.gov (United States)

Li, Y.; Zhao, G.; Zhu, R.; Kou, Z.

2018-03-01

Based on organic zirconium source as the starting material, by adding chemical modifiers which are made up with photosensitive ZrO2 sol. A uniformed ZrO2 array dot was fabricated with a mean diameter of around 800 nm. By using UV-vis spectra and X-ray photoelectron spectroscopy analysis method, studies the photosensitive ZrO2 gel film of photochemical reaction process and the photosensitive mechanism, to determine the zirconium atom centered chelate structure, reaction formed by metal chelate Zr atom for the center, and to establish the molecular model of the chelate. And studied the ultraviolet light in the process of the variation of the XPS spectra, Zr3d5/2 to 184.9 eV corresponding to the binding energy of the as the combination of state peak gradually reduce; By combining with the status of Zr-O peak gradually increase; The strength of the peak is gradually decline. This suggests that in the process of ultraviolet light photo chemical reaction happened. This study is of great significance to the micro fabrication of ZrO2 array not only to the memory devices but also to the optical devices.

The Study on Thermal Expansion of Ceramic Composites with Addition of ZrW[2]O]8

OpenAIRE

Dedova, Elena Sergeevna; Shadrin, V. S.; Petrushina, M. Y.; Kulkov, Sergey Nikolaevich

2016-01-01

The studies on structure, phase composition and thermal properties of (Al[2]O[3] - 20 wt% ZrO[2]) - ZrW[2]O[8] ceramic composites obtained using nanosized, initial powders were conducted. Homogeneously distributed white particles on the polished surface of composites were observed. Phase composition of the composites was represented with corundum, monoclinic ZrO[2] and two modifications of ZrW[2]O[8] (tetragonal and cubic). Linear thermal expansion coefficient values of the composites were de...

Phase stability and fracture toughness of t' ZrO2 stabilised with MO1.5 (M=Yb and Gd) for thermal barrier application

International Nuclear Information System (INIS)

Loganathan, Archana; Gandhi, Ashutosh S.

2010-01-01

Thermal Barrier coatings (TBC's) protect the gas turbine blades at high temperature exposure. The t' phase is metastable and slowly transforms to the high-temperature equilibrium state consisting of tetragonal (t) and cubic (c) during high temperature exposure. Nanometric grain size also influences the fracture toughness and t' stability. A comparative study of the phase stability and fracture toughness evolution of Yb and Gd stabilized zirconia with composition 8 mol%MO 1.5 . The t' ZrO 2 -8mol% MO 1.5 (M = Yb and Gd) were prepared by co-precipitation method with crystallite size ∼ 20nm. Spark plasma sintering at 1250 deg C for 10 min was carried out to produce compacts with ∼ 96% relative density for fracture toughness measurements. The dense compacts were heat treated at 1250 deg C upto 192h. XRD studies revealed the partitioning of t' to t+c. No spontaneous monoclinic phase formed during cooling, except after 192h exposure. The fracture toughness of the sintered pellets with various time intervals of thermal exposure was measured. The results were analysed in terms of the effect of phase constitution on fracture toughness. The role of ferroelastic toughening in these materials was explored. (author)

The comparison of photocatalytic activity of synthesized TiO2 and ZrO2 nanosize onto wool fibers

International Nuclear Information System (INIS)

Moafi, Hadi Fallah; Shojaie, Abdollah Fallah; Zanjanchi, Mohammad Ali

2010-01-01

TiO 2 and ZrO 2 nanocrystals were successfully synthesized and deposited onto wool fibers using the sol-gel technique at low temperature. The photocatalytic activities of TiO 2 -coated and ZrO 2 -coated wool fibers were measured by studying photodegradation of methylene blue and eosin yellowish dyes. The initial and the treated samples were characterized by several techniques such as scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and X-ray diffraction. The TEM study shows dispersed particles with 10-30 nm in size for TiO 2 -coated and 20-40 nm in size for ZrO 2 -coated samples on the fiber surface. Comparison of the photocatalytic activity of the coated samples reveals superiority of TiO 2 modified sample with respect to that of ZrO 2 for degradation of both dyes. Our observations indicate that by applying this technique to the fabrics, self-cleaning materials could be designed for practical application.

Thermally and optically stimulated luminescence of AlN-Y2O3 ceramics after ionising irradiation

DEFF Research Database (Denmark)

Trinkler, L.; Bos, A.J.J.; Winkelman, A.J.M.

1999-01-01

, an essential drawback of AlN-Y2O3 is its high fading rate. Special attention has been focused on understanding and improving the fading properties. In particular, the influence of the ceramics production conditions and the additive concentration on the fading rate have been studied. Experimental results......Thermally (TL) and optically stimulated luminescence (OSL) were studied in AlN-Y2O3 ceramics after irradiation with ionising radiation. The extremely high TL sensitivity (approximately 60 times the sensitivity of LiF:Mg,Tl (TLD-100)) makes AlN-Y2O3 ceramics attractive as a TLD material. However...... on spectral properties and thermal evolution of OSL are also presented. The stimulation spectrum covers the spectral range from green to infrared light. A combination of thermal and optical stimulation allowed a correlation to be found between parameters of OSL and TL after the same irradiation dose...

The synthesis of poly(vinyl chloride) nanocomposite films containing ZrO2 nanoparticles modified with vitamin B1 with the aim of improving the mechanical, thermal and optical properties.

Science.gov (United States)

Mallakpour, Shadpour; Shafiee, Elaheh

2017-01-01

In the present investigation, solution casting method was used for the preparation of nanocomposite (NC) films. At first, the surface of ZrO 2 nanoparticles (NPs) was modified with vitamin B 1 (VB 1 ) as a bioactive coupling agent to achieve a better dispersion and compatibility of NPs within the poly(vinyl chloride) (PVC) matrix. The grafting of modifier on the surface of ZrO 2 was confirmed by Fourier transform infrared spectroscopy and thermogravimetric analysis (TGA). Finally, the resulting modified ZrO 2 (ZrO 2 -VB 1 ), was used as a nano-filler and incorporated into the PVC matrix to improve its mechanical and thermal properties. These processes were carried out under ultrasonic irradiation conditions, which is an economical and eco-friendly method. The effect of ZrO 2 -VB 1 on the properties and morphology of the PVC matrix was characterized by various techniques. Field emission scanning electron microscopy and transmission electron microscopy analyses showed a good dispersion of fillers into the PVC matrix with the average diameter of 37-40 nm. UV-Vis spectroscopy was used to study optical behavior of the obtained NC films. TGA analysis has confirmed the presence of about 7 wt% VB 1 on the surface of ZrO 2 . Also, the data indicated that the thermal and mechanical properties of the NC films were enhanced.

Novel support effects on the mechanism of propene-deuterium: Addition and exchange reactions over dispersed ZrO2

International Nuclear Information System (INIS)

Naito, Shuichi; Tanimoto, Mitsutoshi

1995-01-01

The effect on the rate and mechanisms of propene-deuterium reactions of dispersing ZrO 2 on various supports such as silica, alumina, and titanium dioxide has been studied by microwave spectroscopic analysis of monodeuteropropene as well as by kinetic investigation. By dispersal of ZrO 2 on these supports, the rate of the C 3 H 6 -D 2 reactions is increased considerbly compared to that over unsupported ZrO 2 , with the decrease of activation energy. Hydrogen exchange in propene proceeds simultaneously with addition via the associative mechanism through n-propyl and s-propyl intermediates. Through XPS analysis of ZrO 2 /SiO 2 , it was found that a monolayer of ZrO 2 is formed over the silica support. The monolayer catalyst exhibits catalytic behavior quite different from that of unsupported ZrO 2 . On the other hand, alumina surfaces modified by ZrO 2 layers may be the main active sites in the case of ZrO 2 /Al 2 O 3 . The marked enhancement of the reaction rate in the lower loading region of ZrO 2 /TiO 2 may be explained by the strong interaction of atomically dispersed zirconium ions with active centers on TiO 2 . 28 refs., 10 figs., 1 tab

Facile synthesis of luminescent and amorphous La2O3-ZrO2:Eu3+ nanofibrous membranes with robust softness

Science.gov (United States)

Han, Weidong; Ding, Bin; Park, Mira; Cui, Fuhai; Ghouri, Zafar Khan; Saud, Prem Singh; Kim, Hak-Yong

2015-08-01

Novel luminescent and amorphous La2O3-ZrO2:Eu3+ (LZE) nanofibrous membranes with robust softness are fabricated for the first time via a facile electrospinning technique. By incorporating zirconium oxide, the as-prepared lanthanum oxide nanofibrous membranes can be dramatically changed from extreme fragility to robust softness. Meanwhile, the softness and luminescent performance of LZE nanofibrous membranes can be finely controlled by regulating the doping concentration of zirconium oxide and europium in lanthanum oxide nanofibers. Additionally, the crystal structure analysis using X-ray diffractometer and high resolution transmission electron microscopy measurements have confirmed the correlation between the amorphous structure and softness. Furthermore, LZE membranes show the characteristic emission of Eu3+ corresponding to 5D0, 1, 2-7F0, 1, 2, 3, 4 transitions due to an efficient energy transfer from O2- to Eu3+. The LZE nanofibrous membranes with the optimum doping Eu3+ concentration of 3 mol% exhibit excellent softness and luminescent properties, which make the materials to have potential applications in fluorescent lamps and field emission displays.Novel luminescent and amorphous La2O3-ZrO2:Eu3+ (LZE) nanofibrous membranes with robust softness are fabricated for the first time via a facile electrospinning technique. By incorporating zirconium oxide, the as-prepared lanthanum oxide nanofibrous membranes can be dramatically changed from extreme fragility to robust softness. Meanwhile, the softness and luminescent performance of LZE nanofibrous membranes can be finely controlled by regulating the doping concentration of zirconium oxide and europium in lanthanum oxide nanofibers. Additionally, the crystal structure analysis using X-ray diffractometer and high resolution transmission electron microscopy measurements have confirmed the correlation between the amorphous structure and softness. Furthermore, LZE membranes show the characteristic emission of Eu3

Effect of H2O and Y(O on Oxidation Behavior of NiCoCrAl Coating Within Thermal Barrier Coating

Directory of Open Access Journals (Sweden)

WANG Yi-qun

2017-04-01

Full Text Available NiCoCrAl coatings containing Y and Y oxide were made using vacuum plasma deposition and high-velocity oxygen fuel respectively, high temperature oxidation dynamics and cross-section microstructures of NiCoCrAl+Y and NiCoCrAl+Y(O coatings in Ar-16.7%O2, Ar-3.3%H2O and Ar-0.2%H2-0.9%H2O at 1100℃ were investigated by differential thermal analysis (DTA and optical and electron microscope. The influencing mechanism of Y oxide on the oxidation of coatings at different atmosphere was compared by computation using First-Principles. The results show that Al2O3 layer on NiCoCrAl+Y coatings has more holes for internal oxidation on account of the element Y diffusion and enrichment on the interface. In addition, steam can promote the internal oxidation. While a thinner and uniform alumina form on NiCoCrAl+Y(O coatings because element Y is pinned by oxygen atoms during the preparation of coatings. Water vapor has less influence on protective alumina formation on the NiCoCrAl+Y(O coating. Therefore, oxidation behavior of NiCoCrAl coatings vary in composition and structure in different oxidizing atmosphere. Besides, Y and Y-enrichment oxides have key influences on the microstructure and the growth rate.

Hydrothermal synthesis and white light emission of cubic ZrO2:Eu3+ nanocrystals

International Nuclear Information System (INIS)

Meetei, Sanoujam Dhiren; Singh, Shougaijam Dorendrajit

2014-01-01

Highlights: • White light emitting cubic ZrO 2 :Eu 3+ nanocrystal is synthesized by hydrothermal technique. • Eu 3+ is used to stabilize crystalline phase and to get red counterpart of the white light. • Defect emission and Eu 3+ emission combined to give white light. • The white light emitted from this nanocrystal resembles vertical daylight of the Sun. • Lifetime corresponding to red counterpart of the sample is far longer than conventional white light emitters. -- Abstract: Production of white light has been a promising area of luminescence studies. In this work, white light emitting nanocrystals of cubic zirconia doped with Eu 3+ are synthesized by hydrothermal technique. The dopant Eu 3+ is used to stabilize crystalline phase to cubic and at the same time to get red counterpart of the white light. The synthesis procedure is simple and precursor required no further annealing for crystallization. X-ray diffraction patterns show the crystalline phase of ZrO 2 :Eu 3+ to be cubic and it is confirmed by Fourier Transform Infrared spectroscopy. From transmission electron microscopy images, size of the crystals is found to be ∼5 nm. Photoluminescence emission spectrum of the sample, on monitoring excitation at O 2− –Eu 3+ charge transfer state shows broad peak due to O 2− of the zirconia and that of Eu 3+ emission. Commission Internationale de l’éclairage co-ordinate of this nanocrystal (0.32, 0.34) is closed to that of the ideal white light (0.33, 0.33). Correlated color temperature of the white light (5894 K) is within the range of vertical daylight. Lifetime (1.32 ms) corresponding to 5 D 0 energy level of the Eu 3+ is found to be far longer than conventional red counterparts of white light emitters. It suggests that the ZrO 2 :Eu 3+ nanocrystals synthesized by hydrothermal technique may find applications in simulating the vertical daylight of the Sun

Impact of nano and bulk ZrO2, TiO2 particles on soil nutrient contents and PGPR.

Science.gov (United States)

Karunakaran, Gopalu; Suriyaprabha, Rangaraj; Manivasakan, Palanisamy; Yuvakkumar, Rathinam; Rajendran, Venkatachalam; Kannan, Narayanasamy

2013-01-01

Currently, nanometal oxides are used extensively in different industries such as medicine, cosmetics and food. The increased consumption of nanoparticles (NPs) leads the necessity to understand the fate of the nanoparticles in the environment. The present study focused on the ecotoxicological behaviour of bulk and nano ZrO2 (Zirconia) and TiO2 (Titania) particles on PGPR (plant growth promoting rhizobacteria), soil and its nutrient contents. The microbial susceptibility study showed that nano TiO2 had 13 +/- 0.9 mm (B. megaterium), 15 +/- 0.2 mm (P. fluorescens), 16 +/- 0.2 mm (A. vinelandii) and 12 +/- 0.3 mm (B. brevis) zones of inhibition. However, nano and bulk ZrO2 particles were non-toxic to PGPR. In addition, it was found that toxicity varied depends on the medium of reaction. The soil study showed that nano TiO2 was found to be highly toxic, whereas bulk TiO2 was less toxic towards soil bacterial populations at 1000 mg L(-1). In contrast, nano and bulk ZrO2 were found to be inert at 1000 mg L(-1). The observed zeta potential and hydrophobicity of TiO2 particles causes more toxic than ZrO2 in parallel with particle size. However, nano TiO2 decreases the microbial population as well as nutrient level of the soil but not zirconia. Our finding shows that the mechanism of toxicity depends on size, hydrophobic potential and zeta potential of the metal oxide particles. Thus, it is necessary to take safety measures during the disposal and use of such toxic nanoparticles in the soil to prevent their hazardous effects.

Microstructural and microchemical characterization of the interface between La_0.85Sr_0.15MnO₃ and Y₂O₃-stabilized ZrO₂

DEFF Research Database (Denmark)

Clausen, C.; Bagger, C.; Bilde-Sørensen, Jørgen

1994-01-01

La0.85Sr0.15MnO3 and Y2O3-stabilized ZrO2 may be used as cathode and electrolyte materials, respectively, in solid oxide fuel cells. One of the requirements of the cathode-electrolyte interface is that high impedance phases are not formed at the interface during manufacture or operation of the SOFC....... The interfaces of interest were prepared as a diffusion couple and by sintered powder mixtures of La0.85Sr0.15MnO3 and Y2O3-stabilized ZrO2. The structures at the interfaces were examined by transmission electron microscopy. Chemical analyses were made by energy dispersive X-ray spectroscopy. A Zr, La......-based pyrochlore-type crystalline phase has been observed at some of the interfaces between La0.85Sr0.15MnO3 and Y2O3-stabilized ZrO2. In the present paper, changes in element ratios are used to obtain knowledge on how the elements diffuse with respect to each other at the interface. It was found...

Acoustic Emission Analysis of Damage Progression in Thermal Barrier Coatings Under Thermal Cyclic Conditions

Science.gov (United States)

Appleby, Matthew; Zhu, Dongming; Morscher, Gregory

2015-01-01

Damage evolution of electron beam-physical vapor deposited (EBVD-PVD) ZrO2-7 wt.% Y2O3 thermal barrier coatings (TBCs) under thermal cyclic conditions was monitored using an acoustic emission (AE) technique. The coatings were heated using a laser heat flux technique that yields a high reproducibility in thermal loading. Along with AE, real-time thermal conductivity measurements were also taken using infrared thermography. Tests were performed on samples with induced stress concentrations, as well as calcium-magnesium-alumino-silicate (CMAS) exposure, for comparison of damage mechanisms and AE response to the baseline (as-produced) coating. Analysis of acoustic waveforms was used to investigate damage development by comparing when events occurred, AE event frequency, energy content and location. The test results have shown that AE accumulation correlates well with thermal conductivity changes and that AE waveform analysis could be a valuable tool for monitoring coating degradation and provide insight on specific damage mechanisms.

Optical and structural characterization of Ge clusters embedded in ZrO2

OpenAIRE

Agocs, E; Zolnai, Z.; Rossall, A. K.; Van den Berg, Jakob; Fodor, B.; Lehninger, D.; Khomenkova, L.; Ponomaryov, S.; Gudymenko, O.; Yukhymchuk, V.; Kalas, B.; Heitmann, J.; Petrik, P.

2017-01-01

The change of optical and structural properties of Ge nanoclusters in ZrO2 matrix have been investigated by spectroscopic ellipsometry versus annealing temperatures. Radio-frequency top-down magnetron sputtering approach was used to produce the samples of different types, i.e. single-layers of pure Ge, pure ZrO2 and Ge-rich-ZrO2 as well as multi-layers stacked of 40 periods of 5-nm-Ge-rich-ZrO2 layers alternated by 5-nm-ZrO2 ones. Germanium nanoclusters in ZrO2 host were formed by rapid-therm...

Lattice vibrations and cubic to tetragonal phase transition in ZrO2

International Nuclear Information System (INIS)

Negita, K.

1989-01-01

On the basis of analyses of phonon modes in ZrO 2 , it is suggested that condensation of a phonon X 2 - at the cubic Brillouin zone boundary X point, (0, 0, 2 π/a), is associated with the cubic to tetragonal phase transition in ZrO 2 . Free energy consideration shows that spontaneous volume and shear strains, e Alg = (e 1 +e 2 +e 3 ) and e Eg = (2e 3 - e 1 - e 2 )/ Λ3, are induced in the tetragonal phase as a result of indirect couplings of the X 2 - mode to homogeneous elastic strains; the tetragonal phase is improper ferroelastic

Sinterização e propriedades mecânicas do compósito Y-TZP/Al2O3 Sintering and mechanical properties of the Y-TZP/Al2O3 composites

Directory of Open Access Journals (Sweden)

L. H. P. Teixeira

2007-09-01

Full Text Available Foi estudado o efeito da adição de Al2O3 nas propriedades de cerâmicas à base de ZrO2 tetragonal estabilizada com ítria (Y-TZP visando sua aplicação como material dentário. Amostras contendo 0, 10, 20 e 30% em peso de Al2O3 foram compactadas por prensagem uniaxial a frio (80 MPa e em seguida sinterizadas ao ar a 1500, 1550 e 1600 °C por 120 min. Os efeitos destas condições de sinterização nas propriedades dos materiais foram analisados por difração de raios X e microscopia eletrônica de varredura. As propriedades mecânicas de dureza e tenacidade à fratura foram determinadas, utilizando-se o método de indentação Vickers. Além disso, algumas amostras foram submetidas a ensaio de flexão em 4 pontos. Cerâmicas de elevada densidade relativa foram obtidas, com dureza variando entre 13,4 e 15,8 GPa, dependendo da quantidade de Al2O3 adicionada à matriz de ZrO2. Por outro lado, não foi verificada uma influencia significativa da adição de Al2O3 na tenacidade à fratura, que apresentou valores próximos de 8 MPa.m½, em quase todas as situações. A boa dureza, a elevada tenacidade à fratura, a boa resistência à fratura (sigmaf = 685 MPa e o módulo de Weibull (m=11 apresentados pelos materiais com adições de 20% de Al2O3, indicam a confiabilidade do compósito como um potencial biomaterial para uso na implantodontia.In this work, the influence of Al2O3 addition on the tetragonal ZrO2 ceramic properties was studied, aiming the use of this ceramic as dental materials. Samples containing 0, 10, 20 e 30 wt.% were cold pressed (80 MPa, and sintered in air, at 1500, 1550 e 1600 °C, for 120 min. The effects of the sintering conditions were analyzed by X-ray diffraction and Scanning Electron Microscopy. Hardness and fracture toughness were determined by Vicker's indentation method. Furthermore, samples were submitted to the 4 point bending test. Dense ceramics were obtained, with hardness values varying around 13.4 and 15.8 GPa

Partial redetermination of the phase diagram of the system Al2O3 - ZrO2 - SiO2

International Nuclear Information System (INIS)

Greca, M.C.; Emiliano, J.V.; Segadaes, A.M.

1990-01-01

Current research on the mechanical behaviour of ceramic matrices reinforced by zirconia particles, and on the processing of mullite-zirconia via reaction-sintering, has brought about the need to update the phase diagram of the system Al 2 O 3 -ZrO 2 -SiO 2 , whose available version dates back to 1956. In the present work, selected compositions in this system were prepared from reagent-grade oxides, uniaxially pressed into 6 mm cylindrical pellets, fired at temperatures between 1550 and 1750 0 C for 6 to 24 h, water-quenched, and observed by X-ray diffraction and SEM, the composition of some of the phases identified being evaluated by EPMA. The data so obtained led to the relocation of the boundary curves neighbouring the ternary eutectic involving alumina, zirconia and mullite. This eutectic was found to occur at ∼ 1750 0 C, a temperature significantly lower than previously reported. (author) [pt

Phase formation in the systems ZrO2-H2SO4-Na2SO4 (NaCl)-H2O

International Nuclear Information System (INIS)

Sozinova, Yu.P.; Motov, D.L.; Rys'kina, M.P.

1988-01-01

Formation of solid phases in the systems ZrO 2 - H 2 SO 4 - Na 2 SO 4 (NaCl) - H 2 O at 25 and 75 deg C is studied. Three basic Na 2 Zr(OH) 2 (SO 4 ) 2 x (0.2 - 0.4)H 2 O, NaZrOH(SO 4 ) 2 x H 2 O, NaZrO 0.5 (OH) 2 SO 4 x 2H 2 O and three normal sodium sulfatozirconates Na 2 Zr(SO 4 ) 3 x 3H 2 O, Na 4 Zr(SO 4 ) 4 x 3H 2 O, Na 6 Zr(SO 4 ) 5 x 4H 2 O have been isolated, their solubility and crystal optical properties are determined