A proposed phase equilibrium diagram for Pt-Zr system

International Nuclear Information System (INIS)

Arias, D.E.; Gribaudo, L.

1993-01-01

A revision of the phase diagram of the Pt-Zr system is presented using up to date information from recent publications. The proposed change concerning the invariant transformation in the Pt-rich zone is supported by simplified thermodynamic evaluations. (author). 12 refs., 1 fig

The Butterfly Diagram Internal Structure

International Nuclear Information System (INIS)

Ternullo, Maurizio

2013-01-01

A time-latitude diagram, where the spotgroup area is taken into account, is presented for cycles 12 through 23. The results show that the spotted area is concentrated in few, small portions ( k nots ) of the Butterfly Diagram (BD). The BD may be described as a cluster of knots. Knots are distributed in the butterfly wings in a seemingly randomly way. A knot may appear at either lower or higher latitudes than previous ones, in spite of the prevalent tendency to appear at lower and lower latitudes. Accordingly, the spotted area centroid, far from continuously drifting equatorward, drifts poleward or remains stationary in any hemisphere for significant fractions (≈ 1/3) of the cycle total duration. In a relevant number of semicycles, knots seem to form two roughly parallel, oblique c hains , separated by an underspotted band. This picture suggests that two (or more) ''activity streams'' approach the equator at a rate higher than the spot zone as a whole.

Drawing Euler Diagrams with Circles

OpenAIRE

Stapleton, Gem; Zhang, Leishi; Howse, John; Rodgers, Peter

2010-01-01

Euler diagrams are a popular and intuitive visualization tool which are used in a wide variety of application areas, including biological and medical data analysis. As with other data visualization methods, such as graphs, bar charts, or pie charts, the automated generation of an Euler diagram from a suitable data set would be advantageous, removing the burden of manual data analysis and the subsequent task of drawing an appropriate diagram. Various methods have emerged that automatically dra...

Stage line diagram: an age-conditional reference diagram for tracking development.

Science.gov (United States)

van Buuren, Stef; Ooms, Jeroen C L

2009-05-15

This paper presents a method for calculating stage line diagrams, a novel type of reference diagram useful for tracking developmental processes over time. Potential fields of applications include: dentistry (tooth eruption), oncology (tumor grading, cancer staging), virology (HIV infection and disease staging), psychology (stages of cognitive development), human development (pubertal stages) and chronic diseases (stages of dementia). Transition probabilities between successive stages are modeled as smoothly varying functions of age. Age-conditional references are calculated from the modeled probabilities by the mid-P value. It is possible to eliminate the influence of age by calculating standard deviation scores (SDS). The method is applied to the empirical data to produce reference charts on secondary sexual maturation. The mean of the empirical SDS in the reference population is close to zero, whereas the variance depends on age. The stage line diagram provides quick insight into both status (in SDS) and tempo (in SDS/year) of development of an individual child. Other measures (e.g. height SDS, body mass index SDS) from the same child can be added to the chart. Diagrams for sexual maturation are available as a web application at http://vps.stefvanbuuren.nl/puberty. The stage line diagram expresses status and tempo of discrete changes on a continuous scale. Wider application of these measures scores opens up new analytic possibilities. (c) 2009 John Wiley & Sons, Ltd.

Diagram Size vs. Layout Flaws: Understanding Quality Factors of UML Diagrams

DEFF Research Database (Denmark)

Störrle, Harald

2016-01-01

, though, is our third goal of extending our analysis aspects of diagram quality. Method: We improve our definition of diagram size and add a (provisional) definition of diagram quality as the number of topographic layout flaws. We apply these metrics on 60 diagrams of the five most commonly used types...... of UML diagram. We carefully analyze the structure of our diagram samples to ensure representativeness. We correlate diagram size and layout quality with modeler performance data obtained in previous experiments. The data set is the largest of its kind (n-156). Results: We replicate earlier findings......, and extend them to two new diagram types. We provide an improved definition of diagram size, and provide a definition of topographic layout quality, which is one more step towards a comprehensive definition of diagram quality as such. Both metrics are shown to be objectively applicable. We quantify...

Stereo 3D spatial phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Kang, Jinwu, E-mail: kangjw@tsinghua.edu.cn; Liu, Baicheng, E-mail: liubc@tsinghua.edu.cn

2016-07-15

Phase diagrams serve as the fundamental guidance in materials science and engineering. Binary P-T-X (pressure–temperature–composition) and multi-component phase diagrams are of complex spatial geometry, which brings difficulty for understanding. The authors constructed 3D stereo binary P-T-X, typical ternary and some quaternary phase diagrams. A phase diagram construction algorithm based on the calculated phase reaction data in PandaT was developed. And the 3D stereo phase diagram of Al-Cu-Mg ternary system is presented. These phase diagrams can be illustrated by wireframe, surface, solid or their mixture, isotherms and isopleths can be generated. All of these can be displayed by the three typical display ways: electronic shutter, polarization and anaglyph (for example red-cyan glasses). Especially, they can be printed out with 3D stereo effect on paper, and watched by the aid of anaglyph glasses, which makes 3D stereo book of phase diagrams come to reality. Compared with the traditional illustration way, the front of phase diagrams protrude from the screen and the back stretches far behind of the screen under 3D stereo display, the spatial structure can be clearly and immediately perceived. These 3D stereo phase diagrams are useful in teaching and research. - Highlights: • Stereo 3D phase diagram database was constructed, including binary P-T-X, ternary, some quaternary and real ternary systems. • The phase diagrams can be watched by active shutter or polarized or anaglyph glasses. • The print phase diagrams retains 3D stereo effect which can be achieved by the aid of anaglyph glasses.

Phase diagrams of the elements

International Nuclear Information System (INIS)

Young, D.A.

1975-01-01

A summary of the pressure-temperature phase diagrams of the elements is presented, with graphs of the experimentally determined solid-solid phase boundaries and melting curves. Comments, including theoretical discussion, are provided for each diagram. The crystal structure of each solid phase is identified and discussed. This work is aimed at encouraging further experimental and theoretical research on phase transitions in the elements

Safety- barrier diagrams

DEFF Research Database (Denmark)

Duijm, Nijs Jan

2008-01-01

Safety-barrier diagrams and the related so-called 'bow-tie' diagrams have become popular methods in risk analysis. This paper describes the syntax and principles for constructing consistent and valid safety-barrier diagrams. The relation of safety-barrier diagrams to other methods such as fault...... trees and Bayesian networks is discussed. A simple method for quantification of safety-barrier diagrams is proposed. It is concluded that safety-barrier diagrams provide a useful framework for an electronic data structure that integrates information from risk analysis with operational safety management....

Development and application of α-hull and Voronoi diagrams in the assessment of roundness error

International Nuclear Information System (INIS)

Li, Xiuming; Liu, Hongqi; Li, Wei

2011-01-01

Computational geometry has been used to select effective data points from the measured data points for evaluating the roundness error to improve the computational complexity. However, for precision parts most of the measured points are on the vertices of the convex hull; it cannot have any effect on improving the computational complexity with the Voronoi diagrams. In this paper the roundness error is evaluated with α-hull and the Voronoi diagram instead of convex hull. An approach for constructing α-hull with the minimum radius separation is presented to determine the vertices of the Voronoi diagram. The experimental results showed that the roundness error of the minimum zone circle could be solved efficiently with α-hull and the Voronoi diagram

Collaborative diagramming during problem based learning in medical education: Do computerized diagrams support basic science knowledge construction?

Science.gov (United States)

De Leng, Bas; Gijlers, Hannie

2015-05-01

To examine how collaborative diagramming affects discussion and knowledge construction when learning complex basic science topics in medical education, including its effectiveness in the reformulation phase of problem-based learning. Opinions and perceptions of students (n = 70) and tutors (n = 4) who used collaborative diagramming in tutorial groups were collected with a questionnaire and focus group discussions. A framework derived from the analysis of discourse in computer-supported collaborative leaning was used to construct the questionnaire. Video observations were used during the focus group discussions. Both students and tutors felt that collaborative diagramming positively affected discussion and knowledge construction. Students particularly appreciated that diagrams helped them to structure knowledge, to develop an overview of topics, and stimulated them to find relationships between topics. Tutors emphasized that diagramming increased interaction and enhanced the focus and detail of the discussion. Favourable conditions were the following: working with a shared whiteboard, using a diagram format that facilitated distribution, and applying half filled-in diagrams for non-content expert tutors and\\or for heterogeneous groups with low achieving students. The empirical findings in this study support the findings of earlier more descriptive studies that diagramming in a collaborative setting is valuable for learning complex knowledge in medicine.

Beyond the classic thermoneutral zone: Including thermal comfort.

Science.gov (United States)

Kingma, Boris Rm; Frijns, Arjan Jh; Schellen, Lisje; van Marken Lichtenbelt, Wouter D

2014-01-01

The thermoneutral zone is defined as the range of ambient temperatures where the body can maintain its core temperature solely through regulating dry heat loss, i.e., skin blood flow. A living body can only maintain its core temperature when heat production and heat loss are balanced. That means that heat transport from body core to skin must equal heat transport from skin to the environment. This study focuses on what combinations of core and skin temperature satisfy the biophysical requirements of being in the thermoneutral zone for humans. Moreover, consequences are considered of changes in insulation and adding restrictions such as thermal comfort (i.e. driver for thermal behavior). A biophysical model was developed that calculates heat transport within a body, taking into account metabolic heat production, tissue insulation, and heat distribution by blood flow and equates that to heat loss to the environment, considering skin temperature, ambient temperature and other physical parameters. The biophysical analysis shows that the steady-state ambient temperature range associated with the thermoneutral zone does not guarantee that the body is in thermal balance at basal metabolic rate per se. Instead, depending on the combination of core temperature, mean skin temperature and ambient temperature, the body may require significant increases in heat production or heat loss to maintain stable core temperature. Therefore, the definition of the thermoneutral zone might need to be reformulated. Furthermore, after adding restrictions on skin temperature for thermal comfort, the ambient temperature range associated with thermal comfort is smaller than the thermoneutral zone. This, assuming animals seek thermal comfort, suggests that thermal behavior may be initiated already before the boundaries of the thermoneutral zone are reached.

Thermodynamic study of CVD-ZrO2 phase diagrams

International Nuclear Information System (INIS)

Torres-Huerta, A.M.; Vargas-Garcia, J.R.; Dominguez-Crespo, M.A.; Romero-Serrano, J.A.

2009-01-01

Chemical vapor deposition (CVD) of zirconium oxide (ZrO 2 ) from zirconium acetylacetonate Zr(acac) 4 has been thermodynamically investigated using the Gibbs' free energy minimization method and the FACTSAGE program. Thermodynamic data Cp o , ΔH o and S o for Zr(acac) 4 have been estimated using the Meghreblian-Crawford-Parr and Benson methods because they are not available in the literature. The effect of deposition parameters, such as temperature and pressure, on the extension of the region where pure ZrO 2 can be deposited was analyzed. The results are presented as calculated CVD stability diagrams. The phase diagrams showed two zones, one of them corresponds to pure monoclinic phase of ZrO 2 and the other one corresponds to a mix of monoclinic phase of ZrO 2 and graphite carbon.

78 FR 49684 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-08-15

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

Impulse-Momentum Diagrams

Science.gov (United States)

Rosengrant, David

2011-01-01

Multiple representations are a valuable tool to help students learn and understand physics concepts. Furthermore, representations help students learn how to think and act like real scientists. These representations include: pictures, free-body diagrams, energy bar charts, electrical circuits, and, more recently, computer simulations and…

78 FR 17099 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

Science.gov (United States)

2013-03-20

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including...

78 FR 65874 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-11-04

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including...

75 FR 64673 - Safety Zone, Brandon Road Lock and, Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2010-10-20

... Zone, Brandon Road Lock and, Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and... Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Ship and...: The Coast Guard will enforce Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des...

77 FR 65478 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

Science.gov (United States)

2012-10-29

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River...

77 FR 60044 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2012-10-02

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River...

Zoning Districts, The zoning districts dataset includes the towns in Manitowoc County, WI that have adopted the county's zoning ordinance., Published in 2013, 1:2400 (1in=200ft) scale, Manitowoc County Government.

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — Zoning Districts dataset current as of 2013. The zoning districts dataset includes the towns in Manitowoc County, WI that have adopted the county's zoning ordinance..

76 FR 35106 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-06-16

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago..., DHS. ACTION: Final rule. SUMMARY: The Coast Guard is establishing a permanent safety zone from Brandon... Safety Zones; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary...

Algorithmic phase diagrams

Science.gov (United States)

Hockney, Roger

1987-01-01

Algorithmic phase diagrams are a neat and compact representation of the results of comparing the execution time of several algorithms for the solution of the same problem. As an example, the recent results are shown of Gannon and Van Rosendale on the solution of multiple tridiagonal systems of equations in the form of such diagrams. The act of preparing these diagrams has revealed an unexpectedly complex relationship between the best algorithm and the number and size of the tridiagonal systems, which was not evident from the algebraic formulae in the original paper. Even so, for a particular computer, one diagram suffices to predict the best algorithm for all problems that are likely to be encountered the prediction being read directly from the diagram without complex calculation.

Zr-Fe-Sn Ternary System Phase Diagrams- New Experimental Results

International Nuclear Information System (INIS)

Nieva, N; Gomez, A; Arias, D

2004-01-01

New experimental results for the Zr-Fe-Sn ternary system are presented in this paper. The phases present and equilibrium relations for the 900 o C isothermal on the central zone of the Gibbs triangle are analysed. A set of ternary alloys was designed and obtained, and they were analysed by semi quantitative SEM- EDS, XRD, and metallographic samples. The resulting ternary phase diagrams are presented here (JCH)

A more accurate HR diagram for the cooler stars

International Nuclear Information System (INIS)

Keenan, P.C.

1978-01-01

The author's objective is to classify the fine structure in the pattern in the luminosity-spectrum domain, and thus to define more precisely the borders of zones which are either occupied or avoided by stars of a given population. It is this pattern which is compared with theoretical evolutionary tracks and it is such a diagram based on the revised MK classification of the recent Atlas of Keenan and McNeil (1976) that is presented. (Auth.)

78 FR 4071 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-01-18

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... Coast Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan...

Covariant diagrams for one-loop matching

International Nuclear Information System (INIS)

Zhang, Zhengkang

2016-10-01

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gaugecovariant quantities and are thus dubbed ''covariant diagrams.'' The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhengkang [Michigan Center for Theoretical Physics (MCTP), University of Michigan,450 Church Street, Ann Arbor, MI 48109 (United States); Deutsches Elektronen-Synchrotron (DESY),Notkestraße 85, 22607 Hamburg (Germany)

2017-05-30

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gauge-covariant quantities and are thus dubbed “covariant diagrams.” The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhengkang [Michigan Univ., Ann Arbor, MI (United States). Michigan Center for Theoretical Physics; Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2016-10-15

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gaugecovariant quantities and are thus dubbed ''covariant diagrams.'' The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

International Nuclear Information System (INIS)

Zhang, Zhengkang

2017-01-01

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gauge-covariant quantities and are thus dubbed “covariant diagrams.” The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Experimental phases diagram Zr-Fe and Zr-Sn-Fe of the Fe rich zone at a temperature of 1100oC

International Nuclear Information System (INIS)

Nieva, N.; Jimenez, J.; Gomez, A; Granovsky, M.S

2010-01-01

Zr-based alloys are frequently used in the nuclear energy industry; among these are the Zr-based Zircaloys whose main alloys are Sn and Fe. In order to experimentally evaluate part of the diagram of the binary Zr-Fe phases and the ternary Zr-Sn-Fe in the Fe-rich zone, different binary alloys in the area closest to the composition of the ZrFe 2 and Zr 6 Fe 23 compounds were designed as well as a ternary alloy of Zr-Sn-Fe in the Fe-rich region of the ternary system. All the alloys underwent a two month heat treatment at a temperature of 1100 o C. Later the phases that were present were identified using different complementary techniques (mainly X-ray diffraction and microanalysis). The clear presence of the Zr 6 Fe 23 phase was not observed in any of the alloys. A new ternary phase consisting approximately of Zr 2 0Sn 14 Fe 66 was verified in the ternary alloy

Electronic diagrams

CERN Document Server

Colwell, Morris A

1976-01-01

Electronic Diagrams is a ready reference and general guide to systems and circuit planning and in the preparation of diagrams for both newcomers and the more experienced. This book presents guidelines and logical procedures that the reader can follow and then be equipped to tackle large complex diagrams by recognition of characteristic 'building blocks' or 'black boxes'. The goal is to break down many of the barriers that often seem to deter students and laymen in learning the art of electronics, especially when they take up electronics as a spare time occupation. This text is comprised of nin

Polariton condensation phase diagram in wide-band-gap planar microcavities: GaN versus ZnO

Science.gov (United States)

Jamadi, O.; Réveret, F.; Mallet, E.; Disseix, P.; Médard, F.; Mihailovic, M.; Solnyshkov, D.; Malpuech, G.; Leymarie, J.; Lafosse, X.; Bouchoule, S.; Li, F.; Leroux, M.; Semond, F.; Zuniga-Perez, J.

2016-03-01

The polariton condensation phase diagram is compared in GaN and ZnO microcavities grown on mesa-patterned silicon substrate. Owing to a common platform, these microcavities share similar photonic properties with large quality factors and low photonic disorder, which makes it possible to determine the optimal spot diameter and to realize a thorough phase diagram study. Both systems have been investigated under the same experimental conditions. The experimental results and the subsequent analysis reveal clearly that longitudinal optical phonons have no influence in the thermodynamic region of the condensation phase diagram, while they allow a strong (slight) decrease of the polariton lasing threshold in the trade-off zone (kinetic region). Phase diagrams are compared with numerical simulations using Boltzmann equations, and are in satisfactory agreement. A lower polariton lasing threshold has been measured at low temperature in the ZnO microcavity, as is expected due to a larger Rabi splitting. This study highlights polariton relaxation mechanisms and their importance in polariton lasing.

Adding Value to Force Diagrams: Representing Relative Force Magnitudes

Science.gov (United States)

Wendel, Paul

2011-05-01

Nearly all physics instructors recognize the instructional value of force diagrams, and this journal has published several collections of exercises to improve student skill in this area.1-4 Yet some instructors worry that too few students perceive the conceptual and problem-solving utility of force diagrams,4-6 and over recent years a rich variety of approaches has been proposed to add value to force diagrams. Suggestions include strategies for identifying candidate forces,6,7 emphasizing the distinction between "contact" and "noncontact" forces,5,8 and the use of computer-based tutorials.9,10 Instructors have suggested a variety of conventions for constructing force diagrams, including approaches to arrow placement and orientation2,11-13 and proposed notations for locating forces or marking action-reaction force pairs.8,11,14,15

The Eh-pH Diagram and Its Advances

Directory of Open Access Journals (Sweden)

Hsin-Hsiung Huang

2016-01-01

Full Text Available Since Pourbaix presented Eh versus pH diagrams in his “Atlas of Electrochemical Equilibria in Aqueous Solution”, diagrams have become extremely popular and are now used in almost every scientific area related to aqueous chemistry. Due to advances in personal computers, such diagrams can now show effects not only of Eh and pH, but also of variables, including ligand(s, temperature and pressure. Examples from various fields are illustrated in this paper. Examples include geochemical formation, corrosion and passivation, precipitation and adsorption for water treatment and leaching and metal recovery for hydrometallurgy. Two basic methods were developed to construct an Eh-pH diagram concerning the ligand component(s. The first method calculates and draws a line between two adjacent species based on their given activities. The second method performs equilibrium calculations over an array of points (500 × 800 or higher are preferred, each representing one Eh and one pH value for the whole system, then combines areas of each dominant species for the diagram. These two methods may produce different diagrams. The fundamental theories, illustrated results, comparison and required conditions behind these two methods are presented and discussed in this paper. The Gibbs phase rule equation for an Eh-pH diagram was derived and verified from actual plots. Besides indicating the stability area of water, an Eh-pH diagram normally shows only half of an overall reaction. However, merging two or more related diagrams together reveals more clearly the possibility of the reactions involved. For instance, leaching of Au with cyanide followed by cementing Au with Zn (Merrill-Crowe process can be illustrated by combining Au-CN and Zn-CN diagrams together. A second example of the galvanic conversion of chalcopyrite can be explained by merging S, Fe–S and Cu–Fe–S diagrams. The calculation of an Eh-pH diagram can be extended easily into another dimension, such

76 FR 23524 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-04-27

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago... safety zone from Brandon Road Lock and Dam to Lake Michigan. This proposed safety zone will cover 77.... This TIR established a 77 mile long safety zone from Brandon Road Lock to Lake Michigan in Chicago, IL...

78 FR 36091 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-06-17

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

77 FR 20295 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

Science.gov (United States)

2012-04-04

... Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines...

75 FR 73966 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2010-11-30

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines...

77 FR 35854 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2012-06-15

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines...

76 FR 2829 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-01-18

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines...

75 FR 52462 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2010-08-26

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan including Des Plaines...

77 FR 25595 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2012-05-01

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... Safety Zone; Brandon Road Lock and [[Page 25596

Thermodynamic study of CVD-ZrO{sub 2} phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Torres-Huerta, A.M., E-mail: atorresh@ipn.m [Research Center for Applied Science and Advanced Technology, Altamira-IPN, Altamira C.P.89600 Tamaulipas (Mexico); Vargas-Garcia, J.R. [Dept of Metallurgical Eng., ESIQIE-IPN, Mexico 07300 D.F. (Mexico); Dominguez-Crespo, M.A. [Research Center for Applied Science and Advanced Technology, Altamira-IPN, Altamira C.P.89600 Tamaulipas (Mexico); Romero-Serrano, J.A. [Dept of Metallurgical Eng., ESIQIE-IPN, Mexico 07300 D.F. (Mexico)

2009-08-26

Chemical vapor deposition (CVD) of zirconium oxide (ZrO{sub 2}) from zirconium acetylacetonate Zr(acac){sub 4} has been thermodynamically investigated using the Gibbs' free energy minimization method and the FACTSAGE program. Thermodynamic data Cp{sup o}, DELTAH{sup o} and S{sup o} for Zr(acac){sub 4} have been estimated using the Meghreblian-Crawford-Parr and Benson methods because they are not available in the literature. The effect of deposition parameters, such as temperature and pressure, on the extension of the region where pure ZrO{sub 2} can be deposited was analyzed. The results are presented as calculated CVD stability diagrams. The phase diagrams showed two zones, one of them corresponds to pure monoclinic phase of ZrO{sub 2} and the other one corresponds to a mix of monoclinic phase of ZrO{sub 2} and graphite carbon.

Diagrams benefit symbolic problem-solving.

Science.gov (United States)

Chu, Junyi; Rittle-Johnson, Bethany; Fyfe, Emily R

2017-06-01

The format of a mathematics problem often influences students' problem-solving performance. For example, providing diagrams in conjunction with story problems can benefit students' understanding, choice of strategy, and accuracy on story problems. However, it remains unclear whether providing diagrams in conjunction with symbolic equations can benefit problem-solving performance as well. We tested the impact of diagram presence on students' performance on algebra equation problems to determine whether diagrams increase problem-solving success. We also examined the influence of item- and student-level factors to test the robustness of the diagram effect. We worked with 61 seventh-grade students who had received 2 months of pre-algebra instruction. Students participated in an experimenter-led classroom session. Using a within-subjects design, students solved algebra problems in two matched formats (equation and equation-with-diagram). The presence of diagrams increased equation-solving accuracy and the use of informal strategies. This diagram benefit was independent of student ability and item complexity. The benefits of diagrams found previously for story problems generalized to symbolic problems. The findings are consistent with cognitive models of problem-solving and suggest that diagrams may be a useful additional representation of symbolic problems. © 2017 The British Psychological Society.

Influence diagram in evaluating the subjective judgment

International Nuclear Information System (INIS)

Hong, Y.

1997-01-01

The author developed the idea of the subjective influence diagrams to evaluate subjective judgment. The subjective judgment of a stake holder is a primary decision making proposition. It involves a basic decision process an the individual attitude of the stake holder for his decision purpose. The subjective judgment dominates the some final decisions. A complex decision process may include the subjective judgment. An influence diagram framework is a simplest tool for analyzing subjective judgment process. In the framework, the characters of influence diagrams generate the describing the analyzing, and the evaluating of the subjective judgment. The relationship between the information and the decision, such as independent character between them, is the main issue. Then utility function is the calculating tool to evaluation, the stake holder can make optimal decision. Through the analysis about the decision process and relationship, the building process of the influence diagram identically describes the subjective judgment. Some examples are given to explain the property of subjective judgment and the analysis process

Optimizing UML Class Diagrams

Directory of Open Access Journals (Sweden)

Sergievskiy Maxim

2018-01-01

Full Text Available Most of object-oriented development technologies rely on the use of the universal modeling language UML; class diagrams play a very important role in the design process play, used to build a software system model. Modern CASE tools, which are the basic tools for object-oriented development, can’t be used to optimize UML diagrams. In this manuscript we will explain how, based on the use of design patterns and anti-patterns, class diagrams could be verified and optimized. Certain transformations can be carried out automatically; in other cases, potential inefficiencies will be indicated and recommendations given. This study also discusses additional CASE tools for validating and optimizing of UML class diagrams. For this purpose, a plugin has been developed that analyzes an XMI file containing a description of class diagrams.

PROCESS DIAGRAMS FOR INSTALLATION OF DRIVEN PILES IN PENETRATED WELLS

Directory of Open Access Journals (Sweden)

Kovalev Vladimir Aleksandrovich

2017-03-01

Full Text Available This article presents the main options of improved and newly devised designs and process diagrams for installation of foundations made of driven, or jack, piles in the penetrated wells with expanded shoe, mainly in weak wet (waterlogged and water-saturated soils. The article presents six options of process diagrams for installation of driven piles in penetrated wells, listing the main procedures: for well-compacted weak soils, for the case when the water ingress is excluded, for the case when it is necessary to increase the load-bearing capacity of pile's bearing face in the waterlogged soils, for the case when the load-bearing capacity of the pile shall be increased both for the end and for the sides, for the case when peat or other biogenous water-saturated soils are present at the bottom of the well, and for the case when there is no contracted zone nor practical possibility to ensure the stability of the walls. The proposed six options of process diagrams for installation of the driven piles in penetrated wells provide expansion of their area of application regarding the soil conditions, increase of load-bearing capacity, and possibility of using jack systems for driving the piles under conditions of dense urban development.

75 FR 64147 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2010-10-19

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Ship and Sanitary Canal... . SUPPLEMENTARY INFORMATION: The Coast Guard will enforce Safety Zone, Brandon Road Lock and Dam to Lake Michigan...

76 FR 78161 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-12-16

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... INFORMATION: The Coast Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake...

78 FR 40635 - Safety Zone; Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-07-08

... Zone; Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... Coast Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan...

78 FR 36092 - Safety Zone; Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2013-06-17

... Zone; Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal... Coast Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake Michigan...

CERPHASE: Computer-generated phase diagrams

International Nuclear Information System (INIS)

Ruys, A.J.; Sorrell, C.C.; Scott, F.H.

1990-01-01

CERPHASE is a collection of computer programs written in the programming language basic and developed for the purpose of teaching the principles of phase diagram generation from the ideal solution model of thermodynamics. Two approaches are used in the generation of the phase diagrams: freezing point depression and minimization of the free energy of mixing. Binary and ternary phase diagrams can be generated as can diagrams containing the ideal solution parameters used to generate the actual phase diagrams. Since the diagrams generated utilize the ideal solution model, data input required from the operator is minimal: only the heat of fusion and melting point of each component. CERPHASE is menu-driven and user-friendly, containing simple instructions in the form of screen prompts as well as a HELP file to guide the operator. A second purpose of CERPHASE is in the prediction of phase diagrams in systems for which no experimentally determined phase diagrams are available, enabling the estimation of suitable firing or sintering temperatures for otherwise unknown systems. Since CERPHASE utilizes ideal solution theory, there are certain limitations imposed on the types of systems that can be predicted reliably. 6 refs., 13 refs

Para-equilibrium phase diagrams

International Nuclear Information System (INIS)

Pelton, Arthur D.; Koukkari, Pertti; Pajarre, Risto; Eriksson, Gunnar

2014-01-01

Highlights: • A rapidly cooled system may attain a state of para-equilibrium. • In this state rapidly diffusing elements reach equilibrium but others are immobile. • Application of the Phase Rule to para-equilibrium phase diagrams is discussed. • A general algorithm to calculate para-equilibrium phase diagrams is described. - Abstract: If an initially homogeneous system at high temperature is rapidly cooled, a temporary para-equilibrium state may result in which rapidly diffusing elements have reached equilibrium but more slowly diffusing elements have remained essentially immobile. The best known example occurs when homogeneous austenite is quenched. A para-equilibrium phase assemblage may be calculated thermodynamically by Gibbs free energy minimization under the constraint that the ratios of the slowly diffusing elements are the same in all phases. Several examples of calculated para-equilibrium phase diagram sections are presented and the application of the Phase Rule is discussed. Although the rules governing the geometry of these diagrams may appear at first to be somewhat different from those for full equilibrium phase diagrams, it is shown that in fact they obey exactly the same rules with the following provision. Since the molar ratios of non-diffusing elements are the same in all phases at para-equilibrium, these ratios act, as far as the geometry of the diagram is concerned, like “potential” variables (such as T, pressure or chemical potentials) rather than like “normal” composition variables which need not be the same in all phases. A general algorithm to calculate para-equilibrium phase diagrams is presented. In the limit, if a para-equilibrium calculation is performed under the constraint that no elements diffuse, then the resultant phase diagram shows the single phase with the minimum Gibbs free energy at any point on the diagram; such calculations are of interest in physical vapor deposition when deposition is so rapid that phase

77 FR 19010 - Zone J Tolling Co., LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes...

Science.gov (United States)

2012-03-29

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER12-1301-000] Zone J Tolling Co., LLC; Supplemental Notice That Initial Market- Based Rate Filing Includes Request for Blanket Section 204 Authorization This is a supplemental notice in the above-referenced proceeding of Zone J...

75 FR 26094 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago...

Science.gov (United States)

2010-05-11

...-AA00 Safety Zone, Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago... establishing a temporary safety zone from Brandon Road Lock and Dam to Lake Michigan. This temporary safety...

Sintering diagrams of UO2

International Nuclear Information System (INIS)

Mohan, A.; Soni, N.C.; Moorthy, V.K.

1979-01-01

Ashby's method (see Acta Met., vol. 22, p. 275, 1974) of constructing sintering diagrams has been modified to obtain contribution diagrams directly from the computer. The interplay of sintering variables and mechanisms are studied and the factors that affect the participation of mechanisms in UO 2 are determined. By studying the physical properties, it emerges that the order of inaccuracies is small in most cases and do not affect the diagrams. On the other hand, even a 10% error in activation energies, which is quite plausible, would make a significant difference to the diagram. The main criticism of Ashby's approach is that the numerous properties and equations used, communicate their inaccuracies to the diagrams and make them unreliable. The present study has considerably reduced the number of factors that need to be refined to make the sintering diagrams more meaningful. (Auth.)

Feynman diagram drawing made easy

International Nuclear Information System (INIS)

Baillargeon, M.

1997-01-01

We present a drawing package optimised for Feynman diagrams. These can be constructed interactively with a mouse-driven graphical interface or from a script file, more suitable to work with a diagram generator. It provides most features encountered in Feynman diagrams and allows to modify every part of a diagram after its creation. Special attention has been paid to obtain a high quality printout as easily as possible. This package is written in Tcl/Tk and in C. (orig.)

The Semiotic Structure of Geometry Diagrams: How Textbook Diagrams Convey Meaning

Science.gov (United States)

Dimmel, Justin K.; Herbst, Patricio G.

2015-01-01

Geometry diagrams use the visual features of specific drawn objects to convey meaning about generic mathematical entities. We examine the semiotic structure of these visual features in two parts. One, we conduct a semiotic inquiry to conceptualize geometry diagrams as mathematical texts that comprise choices from different semiotic systems. Two,…

Ring diagrams and phase transitions

International Nuclear Information System (INIS)

Takahashi, K.

1986-01-01

Ring diagrams at finite temperatures carry most infrared-singular parts among Feynman diagrams. Their effect to effective potentials are in general so significant that one must incorporate them as well as 1-loop diagrams. The author expresses these circumstances in some examples of supercooled phase transitions

Revised Pourbaix diagrams for Copper at 5-150 C

International Nuclear Information System (INIS)

Beverskog, B.; Puigdomenech, I.

1995-10-01

Pourbaix diagrams have been revised. Predominance diagrams for dissolved copper species have also been calculated. Five different total concentrations for dissolved copper have been used in the calculations (from 10 -3 to 10 -9 ). The complete hydrolysis series of copper(I) and (II) have not been included in earlier published Pourbaix diagrams, and these species are covered for the first time in this work. At acidic pH, increasing temperature decreases the immunity area, and therefore, it increases the corrosion of the copper. At alkaline pH-values corrosion also increases with the temperature due to the decrease of both passivity and immunity areas. The calculated diagrams are used as a base for the discussion of the corrosion behaviour of the copper canisters in the Swedish radioactive waste management program. 62 refs, 37 figs, 3 tabs

SPECIALIZED MAPPING OF CRUSTAL FAULT ZONES. PART 2: MAIN STAGES AND PROSPECTS

Directory of Open Access Journals (Sweden)

K. Zh. Seminsky

2015-01-01

Full Text Available The article is to complete the description of the special mapping method which theoretical basis and principles were published in [Seminsky, 2014]. With reference to data on the Ulirba site located in Priolkhonie (Western Pribaikalie, the content of special mapping is reviewed in detail. The method is based on paragenetical analysis of abundant jointing which specific feature is the lack of any visible displacement indicators. There are three stages in the special mapping method (Fig. 3 as follows:Stage I: Preparation and analysis of previously published data on the regional fault structure (Fig. 1, А–Г, establishment of a networks of stations to conduct structural geological monitoring and mass measurements of joints, re­cord of rock data (Fig. 2, А, general state of the fault network (Fig. 1, Д–З, fracture density (Fig. 2, Б and, if any, structures of the above-jointing level (Fig. 1, Е, З; Fig. 2, А.Stage II is aimed at processing of field data and includes activities in four groups (II.1–II.4 as follows: Group II.1: construction of circle diagrams, specification of characteristics of joint systems and their typical scatters (Fig. 4, А, identification of simple (generally tipple paragenesises, and determination of dynamic settings of their formation (translocal rank (Table 1, evaluation of densities and complexity of the joint networks, analysis of their spacial patterns within the site under mapping, and identification of the most intensively destructed zones in the rock massif (Fig. 2, Б–В. Group II.2: comparison of jointing diagrams with reference ones showing joint poles (Fig. 4, Б–В; Е–З; Л–Н, and, in case of their satisfactory correlation, making a conclusion of potential formation of a specific joint pattern in the local zone of strike-slip, normal faulting or reverse faulting (Fig. 4,  Г–Д, И–К, О–П; Fig. 5; Fig. 7, Б, and determination of relative age relationships between such zones on

Collaborative diagramming during problem based learning in medical education: Do computerized diagrams support basic science knowledge construction?

NARCIS (Netherlands)

de Leng, Bas; Gijlers, Aaltje H.

2015-01-01

Aim: To examine how collaborative diagramming affects discussion and knowledge construction when learning complex basic science topics in medical education, including its effectiveness in the reformulation phase of problem-based learning. Methods: Opinions and perceptions of students (n = 70) and

Automation of Feynman diagram evaluations

International Nuclear Information System (INIS)

Tentyukov, M.N.

1998-01-01

A C-program DIANA (DIagram ANAlyser) for the automation of Feynman diagram evaluations is presented. It consists of two parts: the analyzer of diagrams and the interpreter of a special text manipulating language. This language can be used to create a source code for analytical or numerical evaluations and to keep the control of the process in general

Comparisons between observational color-magnitude diagrams and synthetic cluster diagrams for young star clusters in the Magellanic Clouds

International Nuclear Information System (INIS)

Recker, S.A.; Brunish, W.M.; Mathews, G.J.

1984-01-01

Young star clusters ( 8 yr) in the Magellanic Clouds (MC) can be used to test the current status of the theory of stellar evolution as applied to intermediate and massive stars. The color-magnitude diagram of many young clusters in the MC shows large numbers of stars in both the main sequence and post main sequence evolutionary phases. Using a grid of stellar evolution models, synthetic cluster H-R diagrams are constructed and compared to observed color-magnitude diagrams to determine the age, age spread, and composition for any given cluster. In addition, for those cases where the data is of high quality, detailed comparisons between theory and observation can provide a diagnostic of the accuracy of the stellar evolution models. Initial indications of these comparisons suggest that the theoretical models should be altered to include: a larger value for the mixing length parameter, a larger rate of mass loss during the asymptotic giant branch phase, and possibly convective overshoot during the core burning phases. (Auth.)

Compatible growth models and stand density diagrams

International Nuclear Information System (INIS)

Smith, N.J.; Brand, D.G.

1988-01-01

This paper discusses a stand average growth model based on the self-thinning rule developed and used to generate stand density diagrams. Procedures involved in testing are described and results are included

Thermochemical properties of silver tellurides including empressite (AgTe) and phase diagrams for Ag-Te and Ag-Te-O

Science.gov (United States)

Voronin, Mikhail V.; Osadchii, Evgeniy G.; Brichkina, Ekaterina A.

2017-10-01

This study compiles original experimental and literature data on the thermodynamic properties (ΔfG°, S°, ΔfH°) of silver tellurides (α-Ag2Te, β-Ag2Te, Ag1.9Te, Ag5Te3, AgTe) obtained by the method of solid-state galvanic cell with the RbAg4I5 and AgI solid electrolytes. The thermodynamic data for empressite (AgTe, pure fraction from Empress Josephine Mine, Colorado USA) have been obtained for the first time by the electrochemical experiment with the virtual reaction Ag + Te = AgTe. The Ag-Te phase diagrams in the T - x and log fTe2 (gas) - 1/ T coordinates have been refined, and the ternary Ag-Te-O diagrams with Ag-Te-TeO2 (paratellurite) composition range have been calculated.

Interrelations between random walks on diagrams (graphs) with and without cycles.

Science.gov (United States)

Hill, T L

1988-05-01

Three topics are discussed. A discrete-state, continuous-time random walk with one or more absorption states can be studied by a presumably new method: some mean properties, including the mean time to absorption, can be found from a modified diagram (graph) in which each absorption state is replaced by a one-way cycle back to the starting state. The second problem is a random walk on a diagram (graph) with cycles. The walk terminates on completion of the first cycle. This walk can be replaced by an equivalent walk on a modified diagram with absorption. This absorption diagram can in turn be replaced by another modified diagram with one-way cycles back to the starting state, just as in the first problem. The third problem, important in biophysics, relates to a long-time continuous walk on a diagram with cycles. This diagram can be transformed (in two steps) to a modified, more-detailed, diagram with one-way cycles only. Thus, the one-way cycle fluxes of the original diagram can be found from the state probabilities of the modified diagram. These probabilities can themselves be obtained by simple matrix inversion (the probabilities are determined by linear algebraic steady-state equations). Thus, a simple method is now available to find one-way cycle fluxes exactly (previously Monte Carlo simulation was required to find these fluxes, with attendant fluctuations, for diagrams of any complexity). An incidental benefit of the above procedure is that it provides a simple proof of the one-way cycle flux relation Jn +/- = IIn +/- sigma n/sigma, where n is any cycle of the original diagram.

VennDiagramWeb: a web application for the generation of highly customizable Venn and Euler diagrams.

Science.gov (United States)

Lam, Felix; Lalansingh, Christopher M; Babaran, Holly E; Wang, Zhiyuan; Prokopec, Stephenie D; Fox, Natalie S; Boutros, Paul C

2016-10-03

Visualization of data generated by high-throughput, high-dimensionality experiments is rapidly becoming a rate-limiting step in computational biology. There is an ongoing need to quickly develop high-quality visualizations that can be easily customized or incorporated into automated pipelines. This often requires an interface for manual plot modification, rapid cycles of tweaking visualization parameters, and the generation of graphics code. To facilitate this process for the generation of highly-customizable, high-resolution Venn and Euler diagrams, we introduce VennDiagramWeb: a web application for the widely used VennDiagram R package. VennDiagramWeb is hosted at http://venndiagram.res.oicr.on.ca/ . VennDiagramWeb allows real-time modification of Venn and Euler diagrams, with parameter setting through a web interface and immediate visualization of results. It allows customization of essentially all aspects of figures, but also supports integration into computational pipelines via download of R code. Users can upload data and download figures in a range of formats, and there is exhaustive support documentation. VennDiagramWeb allows the easy creation of Venn and Euler diagrams for computational biologists, and indeed many other fields. Its ability to support real-time graphics changes that are linked to downloadable code that can be integrated into automated pipelines will greatly facilitate the improved visualization of complex datasets. For application support please contact Paul.Boutros@oicr.on.ca.

Genus Ranges of Chord Diagrams.

Science.gov (United States)

Burns, Jonathan; Jonoska, Nataša; Saito, Masahico

2015-04-01

A chord diagram consists of a circle, called the backbone, with line segments, called chords, whose endpoints are attached to distinct points on the circle. The genus of a chord diagram is the genus of the orientable surface obtained by thickening the backbone to an annulus and attaching bands to the inner boundary circle at the ends of each chord. Variations of this construction are considered here, where bands are possibly attached to the outer boundary circle of the annulus. The genus range of a chord diagram is the genus values over all such variations of surfaces thus obtained from a given chord diagram. Genus ranges of chord diagrams for a fixed number of chords are studied. Integer intervals that can be, and those that cannot be, realized as genus ranges are investigated. Computer calculations are presented, and play a key role in discovering and proving the properties of genus ranges.

Application of the pM'-pCH diagrams in the determination of hydrolysis constants of the lanthanides

International Nuclear Information System (INIS)

Lopez G, H.; Jimenez R, M.; Solache R, M.; Rojas H, A.

2001-01-01

The pM ' -pC H diagrams allowed to determine the saturation and non-saturation zones of Lu(OH) 3 in solid phase and those were applied for determining the hydrolysis and lutetium solubility constants, using the radioactive isotope Lu-177. The first constant of hydrolysis was also determined by the potentiometric method in absence of solid phase. (Author)

Microsoft Visio 2013 business process diagramming and validation

CERN Document Server

Parker, David

2013-01-01

Microsoft Visio 2013 Business Process Diagramming and Validation provides a comprehensive and practical tutorial including example code and demonstrations for creating validation rules, writing ShapeSheet formulae, and much more.If you are a Microsoft Visio 2013 Professional Edition power user or developer who wants to get to grips with both the essential features of Visio 2013 and the validation rules in this edition, then this book is for you. A working knowledge of Microsoft Visio and optionally .NET for the add-on code is required, though previous knowledge of business process diagramming

Process Technical Basis Documentation Diagram for a solid-waste processing facility

International Nuclear Information System (INIS)

Benar, C.J.; Petersen, C.A.

1994-02-01

The Process Technical Basis Documentation Diagram is for a solid-waste processing facility that could be designed to treat, package, and certify contact-handled mixed low-level waste for permanent disposal. The treatment processes include stabilization using cementitious materials and immobilization using a polymer material. The Diagram identifies several engineering/demonstration activities that would confirm the process selection and process design. An independent peer review was conducted at the request of Westinghouse Hanford Company to determine the technical adequacy of the technical approach for waste form development. The peer review panel provided comments and identified documents that it felt were needed in the Diagram as precedence for Title I design. The Diagram is a visual tool to identify traceable documentation of key activities, including those documents suggested by the peer review, and to show how they relate to each other. The Diagram is divided into three sections: (1) the Facility section, which contains documents pertaining to the facility design, (2) the Process Demonstration section, which contains documents pertaining to the process engineering/demonstration work, and 3) the Regulatory section, which contains documents describing the compliance strategy for each acceptance requirement for each feed type, and how this strategy will be implemented

Asymptotic laws for random knot diagrams

Science.gov (United States)

Chapman, Harrison

2017-06-01

We study random knotting by considering knot and link diagrams as decorated, (rooted) topological maps on spheres and pulling them uniformly from among sets of a given number of vertices n, as first established in recent work with Cantarella and Mastin. The knot diagram model is an exciting new model which captures both the random geometry of space curve models of knotting as well as the ease of computing invariants from diagrams. We prove that unknot diagrams are asymptotically exponentially rare, an analogue of Sumners and Whittington’s landmark result for self-avoiding polygons. Our proof uses the same key idea: we first show that knot diagrams obey a pattern theorem, which describes their fractal structure. We examine how quickly this behavior occurs in practice. As a consequence, almost all diagrams are asymmetric, simplifying sampling from this model. We conclude with experimental data on knotting in this model. This model of random knotting is similar to those studied by Diao et al, and Dunfield et al.

Single-particle potential from resummed ladder diagrams

International Nuclear Information System (INIS)

Kaiser, N.

2013-01-01

A recent work on the resummation of fermionic in-medium ladder diagrams to all orders is extended by calculating the complex single-particle potential U(p, k f ) + i W(p, k f ) p > k f . The on-shell single-particle potential is constructed by means of a complex-valued in-medium loop that includes corrections from a test particle of momentum vector p added to the filled Fermi sea. The single-particle potential U(k f , k f ) at the Fermi surface as obtained from the resummation of the combined particle and hole ladder diagrams is shown to satisfy the Hugenholtz-Van-Hove theorem. The perturbative contributions at various orders a n in the scattering length are deduced and checked against the known analytical results at order a 1 and a 2 . The limit a → ∞ is studied as a special case and a strong momentum dependence of the real (and imaginary) single-particle potential is found. This feature indicates an instability against a phase transition to a state with an empty shell inside the Fermi sphere such that the density gets reduced by about 5%. The imaginary single-particle potential vanishes linearly at the Fermi surface. For comparison, the same analysis is performed for the resummed particle-particle ladder diagrams alone. In this truncation an instability for hole excitations near the Fermi surface is found at strong coupling. For the set of particle-hole ring diagrams the single-particle potential is calculated as well. Furthermore, the resummation of in-medium ladder diagrams to all orders is studied for a two-dimensional Fermi gas with a short-range two-body contact interaction. (orig.)

A nonlinear model for fluid flow in a multiple-zone composite reservoir including the quadratic gradient term

International Nuclear Information System (INIS)

Wang, Xiao-Lu; Fan, Xiang-Yu; Nie, Ren-Shi; Huang, Quan-Hua; He, Yong-Ming

2013-01-01

Based on material balance and Darcy's law, the governing equation with the quadratic pressure gradient term was deduced. Then the nonlinear model for fluid flow in a multiple-zone composite reservoir including the quadratic gradient term was established and solved using a Laplace transform. A series of standard log–log type curves of 1-zone (homogeneous), 2-zone and 3-zone reservoirs were plotted and nonlinear flow characteristics were analysed. The type curves governed by the coefficient of the quadratic gradient term (β) gradually deviate from those of a linear model with time elapsing. Qualitative and quantitative analyses were implemented to compare the solutions of the linear and nonlinear models. The results showed that differences of pressure transients between the linear and nonlinear models increase with elapsed time and β. At the end, a successful application of the theoretical model data against the field data shows that the nonlinear model will be a good tool to evaluate formation parameters more accurately. (paper)

Some aspects of fracture assessment diagrams, plastic zone size corrections and contour integrals in post-yield fracture mechanics

International Nuclear Information System (INIS)

Ainsworth, R.A.

1981-03-01

The CEGB failure assessment route is briefly described and is shown to be consistent with a plastic zone size correction method. Modifications to the assessment route which have recently been suggested for describing the effects of thermal and residual stresses are examined. It is shown that the plastic zone size correction method may be used to include local thermal and residual stresses in the assessment route in a simple manner. The assessment route is compared with finite-element solutions for a thermal stress problem and with strip-yield model solutions for a residual stress problem. In using finite-element solutions there are different contour integral methods available for calculating a post-yield fracture parameter. The J-integral of Rice and the J*-integral of Blackburn are examined and compared and the appropriate parameter is identified. (author)

Calculation of Fe–B–V ternary phase diagram

International Nuclear Information System (INIS)

Homolová, Viera; Kroupa, Aleš; Výrostková, Anna

2012-01-01

Highlights: ► Phase diagram of Fe–B–V system was modelled by CALPHAD method. ► Database for thermodynamic calculations for Fe–B–V system was created. ► The new ternary phase was found in 67Fe–18B–15V [in at.%] alloy. - Abstract: The phase equilibria of the Fe–B–V ternary system are studied experimentally and theoretically in this paper. Phase diagram of the system was modelled by CALPHAD method. Boron was modelled as an interstitial element in the FCC and BCC solid solutions. The calculations of isothermal sections of phase diagram are compared with our experimental results at 903 and 1353 K and with available literature experimental data. New ternary phase (with chemical composition 28Fe32V40B in at.%) was found in 67Fe–18B–15V alloy [in at.%]. Further experimental studies for the determination of exact nature of the ternary phase including crystallographic information are necessary.

Causal diagrams in systems epidemiology

Directory of Open Access Journals (Sweden)

Joffe Michael

2012-03-01

Full Text Available Abstract Methods of diagrammatic modelling have been greatly developed in the past two decades. Outside the context of infectious diseases, systematic use of diagrams in epidemiology has been mainly confined to the analysis of a single link: that between a disease outcome and its proximal determinant(s. Transmitted causes ("causes of causes" tend not to be systematically analysed. The infectious disease epidemiology modelling tradition models the human population in its environment, typically with the exposure-health relationship and the determinants of exposure being considered at individual and group/ecological levels, respectively. Some properties of the resulting systems are quite general, and are seen in unrelated contexts such as biochemical pathways. Confining analysis to a single link misses the opportunity to discover such properties. The structure of a causal diagram is derived from knowledge about how the world works, as well as from statistical evidence. A single diagram can be used to characterise a whole research area, not just a single analysis - although this depends on the degree of consistency of the causal relationships between different populations - and can therefore be used to integrate multiple datasets. Additional advantages of system-wide models include: the use of instrumental variables - now emerging as an important technique in epidemiology in the context of mendelian randomisation, but under-used in the exploitation of "natural experiments"; the explicit use of change models, which have advantages with respect to inferring causation; and in the detection and elucidation of feedback.

Causal diagrams in systems epidemiology.

Science.gov (United States)

Joffe, Michael; Gambhir, Manoj; Chadeau-Hyam, Marc; Vineis, Paolo

2012-03-19

Methods of diagrammatic modelling have been greatly developed in the past two decades. Outside the context of infectious diseases, systematic use of diagrams in epidemiology has been mainly confined to the analysis of a single link: that between a disease outcome and its proximal determinant(s). Transmitted causes ("causes of causes") tend not to be systematically analysed.The infectious disease epidemiology modelling tradition models the human population in its environment, typically with the exposure-health relationship and the determinants of exposure being considered at individual and group/ecological levels, respectively. Some properties of the resulting systems are quite general, and are seen in unrelated contexts such as biochemical pathways. Confining analysis to a single link misses the opportunity to discover such properties.The structure of a causal diagram is derived from knowledge about how the world works, as well as from statistical evidence. A single diagram can be used to characterise a whole research area, not just a single analysis - although this depends on the degree of consistency of the causal relationships between different populations - and can therefore be used to integrate multiple datasets.Additional advantages of system-wide models include: the use of instrumental variables - now emerging as an important technique in epidemiology in the context of mendelian randomisation, but under-used in the exploitation of "natural experiments"; the explicit use of change models, which have advantages with respect to inferring causation; and in the detection and elucidation of feedback.

Criteria for evaluating programme theory diagrams in quality improvement initiatives: a structured method for appraisal.

Science.gov (United States)

Issen, Laurel; Woodcock, Thomas; McNicholas, Christopher; Lennox, Laura; Reed, Julie E

2018-04-09

Despite criticisms that many quality improvement (QI) initiatives fail due to incomplete programme theory, there is no defined way to evaluate how programme theory has been articulated. The objective of this research was to develop, and assess the usability and reliability of scoring criteria to evaluate programme theory diagrams. Criteria development was informed by published literature and QI experts. Inter-rater reliability was tested between two evaluators. About 63 programme theory diagrams (42 driver diagrams and 21 action-effect diagrams) were reviewed to establish whether the criteria could support comparative analysis of different approaches to constructing diagrams. Components of the scoring criteria include: assessment of overall aim, logical overview, clarity of components, cause-effect relationships, evidence and measurement. Independent reviewers had 78% inter-rater reliability. Scoring enabled direct comparison of different approaches to developing programme theory; action-effect diagrams were found to have had a statistically significant but moderate improvement in programme theory quality over driver diagrams; no significant differences were observed based on the setting in which driver diagrams were developed. The scoring criteria summarise the necessary components of programme theory that are thought to contribute to successful QI projects. The viability of the scoring criteria for practical application was demonstrated. Future uses include assessment of individual programme theory diagrams and comparison of different approaches (e.g. methodological, teaching or other QI support) to produce programme theory. The criteria can be used as a tool to guide the production of better programme theory diagrams, and also highlights where additional support for QI teams could be needed.

Irradiation distribution diagrams and their use for estimating collectable energy

International Nuclear Information System (INIS)

Ronnelid, M.; Karlsson, B.

1997-01-01

A method for summarising annual or seasonal solar irradiation data in irradiation distribution diagrams, including both direct and diffuse irradiation, is outlined. The practical use of irradiation distribution diagrams is discussed in the paper. Examples are given for the calculation of collectable irradiation on flat plate collectors or trough-like concentrators like the compound parabolic concentrator (CPC), and for the calculation of overhang geometries for windows to prevent overheating of buildings. (author)

On-shell diagrams for N=8 supergravity amplitudes

Energy Technology Data Exchange (ETDEWEB)

Heslop, Paul; Lipstein, Arthur E. [Department of Mathematical Sciences, Durham University,Lower Mountjoy, Stockton Road, Durham, DH1 3LE (United Kingdom)

2016-06-10

We define recursion relations for N=8 supergravity amplitudes using a generalization of the on-shell diagrams developed for planar N=4 super-Yang-Mills. Although the recursion relations generically give rise to non-planar on-shell diagrams, we show that at tree-level the recursion can be chosen to yield only planar diagrams, the same diagrams occurring in the planar N=4 theory. This implies non-trivial identities for non-planar diagrams as well as interesting relations between the N=4 and N=8 theories. We show that the on-shell diagrams of N=8 supergravity obey equivalence relations analogous to those of N=4 super-Yang-Mills, and we develop a systematic algorithm for reading off Grassmannian integral formulae directly from the on-shell diagrams. We also show that the 1-loop 4-point amplitude of N=8 supergravity can be obtained from on-shell diagrams.

Experimenting with Automatic Text-to-Diagram Conversion: A Novel Teaching Aid for the Blind People

Science.gov (United States)

Mukherjee, Anirban; Garain, Utpal; Biswas, Arindam

2014-01-01

Diagram describing texts are integral part of science and engineering subjects including geometry, physics, engineering drawing, etc. In order to understand such text, one, at first, tries to draw or perceive the underlying diagram. For perception of the blind students such diagrams need to be drawn in some non-visual accessible form like tactile…

Effect of a Diagram on Primary Students' Understanding About Electric Circuits

Science.gov (United States)

Preston, Christine Margaret

2017-09-01

This article reports on the effect of using a diagram to develop primary students' conceptual understanding about electric circuits. Diagrammatic representations of electric circuits are used for teaching and assessment despite the absence of research on their pedagogical effectiveness with young learners. Individual interviews were used to closely analyse Years 3 and 5 (8-11-year-old) students' explanations about electric circuits. Data was collected from 20 students in the same school providing pre-, post- and delayed post-test dialogue. Students' thinking about electric circuits and changes in their explanations provide insights into the role of diagrams in understanding science concepts. Findings indicate that diagram interaction positively enhanced understanding, challenged non-scientific views and promoted scientific models of electric circuits. Differences in students' understanding about electric circuits were influenced by prior knowledge, meta-conceptual awareness and diagram conventions including a stylistic feature of the diagram used. A significant finding that students' conceptual models of electric circuits were energy rather than current based has implications for electricity instruction at the primary level.

Zone separator for multiple zone vessels

Science.gov (United States)

Jones, John B.

1983-02-01

A solids-gas contact vessel, having two vertically disposed distinct reaction zones, includes a dynamic seal passing solids from an upper to a lower zone and maintaining a gas seal against the transfer of the separate treating gases from one zone to the other, and including a stream of sealing fluid at the seal.

The mean squared writhe of alternating random knot diagrams

Energy Technology Data Exchange (ETDEWEB)

Diao, Y; Hinson, K [Department of Mathematics and Statistics University of North Carolina at Charlotte, NC 28223 (United States); Ernst, C; Ziegler, U, E-mail: ydiao@uncc.ed [Department of Mathematics and Computer Science, Western Kentucky University, Bowling Green, KY 42101 (United States)

2010-12-10

The writhe of a knot diagram is a simple geometric measure of the complexity of the knot diagram. It plays an important role not only in knot theory itself, but also in various applications of knot theory to fields such as molecular biology and polymer physics. The mean squared writhe of any sample of knot diagrams with n crossings is n when for each diagram at each crossing one of the two strands is chosen as the overpass at random with probability one-half. However, such a diagram is usually not minimal. If we restrict ourselves to a minimal knot diagram, then the choice of which strand is the over- or under-strand at each crossing is no longer independent of the neighboring crossings and a larger mean squared writhe is expected for minimal diagrams. This paper explores the effect on the correlation between the mean squared writhe and the diagrams imposed by the condition that diagrams are minimal by studying the writhe of classes of reduced, alternating knot diagrams. We demonstrate that the behavior of the mean squared writhe heavily depends on the underlying space of diagram templates. In particular this is true when the sample space contains only diagrams of a special structure. When the sample space is large enough to contain not only diagrams of a special type, then the mean squared writhe for n crossing diagrams tends to grow linearly with n, but at a faster rate than n, indicating an intrinsic property of alternating knot diagrams. Studying the mean squared writhe of alternating random knot diagrams also provides some insight into the properties of the diagram generating methods used, which is an important area of study in the applications of random knot theory.

Science and Engineering Students' Use of Diagrams during Note Taking versus Explanation

Science.gov (United States)

Manalo, Emmanuel; Uesaka, Yuri; Perez-Kriz, Sarah; Kato, Masashi; Fukaya, Tatsushi

2013-01-01

The use of diagrams in learning and communication is generally considered efficacious and an important skill to cultivate, especially among science students. At the same time, previous research has revealed many problems in student diagram use, including a lack of spontaneity in such use, but the extent to which these problems persist into the…

Using Affinity Diagrams to Evaluate Interactive Prototypes

DEFF Research Database (Denmark)

Lucero, Andrés

2015-01-01

our particular use of affinity diagramming in prototype evaluations. We reflect on a decade’s experience using affinity diagramming across a number of projects, both in industry and academia. Our affinity diagramming process in interaction design has been tailored and consists of four stages: creating...

76 FR 63199 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-10-12

... Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal...; Brandon Road Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal...

The amplituhedron from momentum twistor diagrams

International Nuclear Information System (INIS)

Bai, Yuntao; He, Song

2015-01-01

We propose a new diagrammatic formulation of the all-loop scattering amplitudes/Wilson loops in planar N=4 SYM, dubbed the “momentum-twistor diagrams”. These are on-shell-diagrams obtained by gluing trivalent black and white vertices in momentum twistor space, which, in the reduced diagram case, are known to be related to diagrams in the original twistor space. The new diagrams are manifestly Yangian invariant, and they naturally represent factorization and forward-limit contributions in the all-loop BCFW recursion relations in momentum twistor space, in a fashion that is completely different from those in momentum space. We show how to construct and evaluate momentum-twistor diagrams, and how to use them to obtain tree-level amplitudes and loop-level integrands; in particular the latter involve isolated bubble-structures for loop variables arising from forward limits, or the entangled removal of particles. From each diagram, the generalized “boundary measurement” directly gives the C, D matrices, thus a cell in the amplituhedron associated with the amplitude, and we expect that our diagrammatic representations of the amplitude provide triangulations of the amplituhedron. To demonstrate the computational power of the formalism, we give explicit results for general two-loop integrands, and the cells of the amplituhedron for two-loop MHV amplitudes.

Idaho National Engineering Laboratory waste area groups 1--7 and 10 Technology Logic Diagram

International Nuclear Information System (INIS)

O'Brien, M.C.; Meservey, R.H.; Little, M.; Ferguson, J.S.; Gilmore, M.C.

1993-09-01

The Technology Logic Diagram was developed to provide technical alternatives for environmental restoration projects at the Idaho National Engineering Laboratory. The diagram (three volumes) documents suggested solutions to the characterization, retrieval, and treatment phases of cleanup activities at contaminated sites within 8 of the laboratory's 10 waste area groups. Contaminated sites at the laboratory's Naval Reactor Facility and Argonne National Laboratory-West are not included in this diagram

Asteroseismic Diagram for Subgiants and Red Giants

Energy Technology Data Exchange (ETDEWEB)

Gai, Ning; Tang, Yanke [College of Physics and Electronic information, Dezhou University, Dezhou 253023 (China); Yu, Peng [College of Physics and Electronic Engineering, Chongqing Normal University, Chongqing 401331 (China); Dou, Xianghua, E-mail: ning_gai@163.com, E-mail: tyk450@163.com [Shandong Provincial Key Laboratory of Biophysics, Dezhou University, Dezhou 253023 (China)

2017-02-10

Asteroseismology is a powerful tool for constraining stellar parameters. NASA’s Kepler mission is providing individual eigenfrequencies for a huge number of stars, including thousands of red giants. Besides the frequencies of acoustic modes, an important breakthrough of the Kepler mission is the detection of nonradial gravity-dominated mixed-mode oscillations in red giants. Unlike pure acoustic modes, mixed modes probe deeply into the interior of stars, allowing the stellar core properties and evolution of stars to be derived. In this work, using the gravity-mode period spacing and the large frequency separation, we construct the ΔΠ{sub 1}–Δ ν asteroseismic diagram from models of subgiants and red giants with various masses and metallicities. The relationship ΔΠ{sub 1}–Δ ν is able to constrain the ages and masses of the subgiants. Meanwhile, for red giants with masses above 1.5 M {sub ⊙}, the ΔΠ{sub 1}–Δ ν asteroseismic diagram can also work well to constrain the stellar age and mass. Additionally, we calculate the relative “isochrones” τ , which indicate similar evolution states especially for similar mass stars, on the ΔΠ{sub 1}–Δ ν diagram.

Diagram Techniques in Group Theory

Science.gov (United States)

Stedman, Geoffrey E.

2009-09-01

Preface; 1. Elementary examples; 2. Angular momentum coupling diagram techniques; 3. Extension to compact simple phase groups; 4. Symmetric and unitary groups; 5. Lie groups and Lie algebras; 6. Polarisation dependence of multiphoton processes; 7. Quantum field theoretic diagram techniques for atomic systems; 8. Applications; Appendix; References; Indexes.

Study of the central region of the ternary diagram Zr-Nb-Fe, Part II

International Nuclear Information System (INIS)

Ramos, C; Saragovi, C; Arias, D; Granovsky, M

2004-01-01

This work continues with the identification and characterization of the intermetallic phases and of the two-phase and three-phase fields associated with the central region of the Zr-Nb-Fe phase diagram. In order to more precisely define the two-phase field βZr + λ 2 and to specify the range of existence in the zone with the highest Fe content for the λ2 phase, new alloys were smelted with the following nominal compositions: Zr 55 Nb 35 Fe 10 and Zr 35 Nb 5 Fe 60 . These alloys were submitted to a thermal treatment at 900 o C for 4 months. The techniques used to identify and characterize the phases in the samples were: optic metallography and electronic sweep, x-ray diffraction and Mossbauer spectroscopy. An isothermic cut of the central region for the Zr-Nb-Fe diagram is proposed considering previous results and those obtained in this work (Cw)

Logic verification system for power plant sequence diagrams

International Nuclear Information System (INIS)

Fukuda, Mitsuko; Yamada, Naoyuki; Teshima, Toshiaki; Kan, Ken-ichi; Utsunomiya, Mitsugu.

1994-01-01

A logic verification system for sequence diagrams of power plants has been developed. The system's main function is to verify correctness of the logic realized by sequence diagrams for power plant control systems. The verification is based on a symbolic comparison of the logic of the sequence diagrams with the logic of the corresponding IBDs (interlock Block Diagrams) in combination with reference to design knowledge. The developed system points out the sub-circuit which is responsible for any existing mismatches between the IBD logic and the logic realized by the sequence diagrams. Applications to the verification of actual sequence diagrams of power plants confirmed that the developed system is practical and effective. (author)

Comprehending 3D Diagrams: Sketching to Support Spatial Reasoning.

Science.gov (United States)

Gagnier, Kristin M; Atit, Kinnari; Ormand, Carol J; Shipley, Thomas F

2017-10-01

Science, technology, engineering, and mathematics (STEM) disciplines commonly illustrate 3D relationships in diagrams, yet these are often challenging for students. Failing to understand diagrams can hinder success in STEM because scientific practice requires understanding and creating diagrammatic representations. We explore a new approach to improving student understanding of diagrams that convey 3D relations that is based on students generating their own predictive diagrams. Participants' comprehension of 3D spatial diagrams was measured in a pre- and post-design where students selected the correct 2D slice through 3D geologic block diagrams. Generating sketches that predicated the internal structure of a model led to greater improvement in diagram understanding than visualizing the interior of the model without sketching, or sketching the model without attempting to predict unseen spatial relations. In addition, we found a positive correlation between sketched diagram accuracy and improvement on the diagram comprehension measure. Results suggest that generating a predictive diagram facilitates students' abilities to make inferences about spatial relationships in diagrams. Implications for use of sketching in supporting STEM learning are discussed. Copyright © 2016 Cognitive Science Society, Inc.

Satake diagrams of affine Kac-Moody algebras

Energy Technology Data Exchange (ETDEWEB)

Tripathy, L K [S B R Government Womens' College, Berhampur, Orissa 760 001 (India); Pati, K C [Department of Physics, Khallikote College, Berhampur, Orissa 760 001 (India)

2006-02-10

Satake diagrams of affine Kac-Moody algebras (untwisted and twisted) are obtained from their Dynkin diagrams. These diagrams give a classification of restricted root systems associated with these algebras. In the case of simple Lie algebras, these root systems and Satake diagrams correspond to symmetric spaces which have recently found many physical applications in quantum integrable systems, quantum transport problems, random matrix theories etc. We hope these types of root systems may have similar applications in theoretical physics in future and may correspond to symmetric spaces analogue of affine Kac-Moody algebras if they exist.

Phase diagram of nuclear 'pasta' and its uncertainties in supernova cores

International Nuclear Information System (INIS)

Sonoda, Hidetaka; Watanabe, Gentaro; Sato, Katsuhiko; Yasuoka, Kenji; Ebisuzaki, Toshikazu

2008-01-01

We examine the model dependence of the phase diagram of inhomogeneous nulcear matter in supernova cores using the quantum molecular dynamics (QMD). Inhomogeneous matter includes crystallized matter with nonspherical nuclei--''pasta'' phases--and the liquid-gas phase-separating nuclear matter. Major differences between the phase diagrams of the QMD models can be explained by the energy of pure neutron matter at low densities and the saturation density of asymmetric nuclear matter. We show the density dependence of the symmetry energy is also useful to understand uncertainties of the phase diagram. We point out that, for typical nuclear models, the mass fraction of the pasta phases in the later stage of the collapsing cores is higher than 10-20%

Magnetic Phase Diagram of α-RuCl3

Science.gov (United States)

Sears, Jennifer; Kim, Young-June; Zhao, Yang; Lynn, Jeffrey

The layered honeycomb material α-RuCl3 is thought to possess unusual magnetic interactions including a strong bond-dependent Kitaev term, offering a potential opportunity to study a material near a well understood spin liquid phase. Although this material orders magnetically at low temperatures and is thus not a realization of a Kitaev spin liquid, it does show a broad continuum of magnetic excitations reminiscent of that expected for the spin liquid phase. It has also been proposed that a magnetic field could destabilize the magnetic order in this material and induce a transition into a spin liquid phase. Low temperature magnetization and specific heat measurements in this material have suggested a complex magnetic phase diagram with multiple unidentified magnetic phases present at low temperature. This has provided motivation for our work characterizing the magnetic transitions and phase diagram in α-RuCl3. I will present detailed bulk measurements combined with magnetic neutron diffraction measurements to map out the phase diagram and identify the various phases present.

Contingency diagrams as teaching tools

OpenAIRE

Mattaini, Mark A.

1995-01-01

Contingency diagrams are particularly effective teaching tools, because they provide a means for students to view the complexities of contingency networks present in natural and laboratory settings while displaying the elementary processes that constitute those networks. This paper sketches recent developments in this visualization technology and illustrates approaches for using contingency diagrams in teaching.

Delimiting diagrams

NARCIS (Netherlands)

Oostrom, V. van

2004-01-01

We introduce the unifying notion of delimiting diagram. Hitherto unrelated results such as: Minimality of the internal needed strategy for orthogonal first-order term rewriting systems, maximality of the limit strategy for orthogonal higher-order pattern rewrite systems (with maximality of the

ROLE OF UML SEQUENCE DIAGRAM CONSTRUCTS IN OBJECT LIFECYCLE CONCEPT

Directory of Open Access Journals (Sweden)

Miroslav Grgec

2007-06-01

Full Text Available When modeling systems and using UML concepts, a real system can be viewed in several ways. The RUP (Rational Unified Process defines the "4 + 1 view": 1. Logical view (class diagram (CD, object diagram (OD, sequence diagram (SD, collaboration diagram (COD, state chart diagram (SCD, activity diagram (AD, 2.Process view (use case diagram, CD, OD, SD, COD, SCD, AD, 3. Development view (package diagram, component diagram, 4. Physical view (deployment diagram, and 5. Use case view (use case diagram, OD, SD, COD, SCD, AD which combines the four mentioned above. With sequence diagram constructs we are describing object behavior in scope of one use case and their interaction. Each object in system goes through a so called lifecycle (create, supplement object with data, use object, decommission object. The concept of the object lifecycle is used to understand and formalize the behavior of objects from creation to deletion. With help of sequence diagram concepts our paper will describe the way of interaction modeling between objects through lifeline of each of them, and their importance in software development.

A novel decision diagrams extension method

International Nuclear Information System (INIS)

Li, Shumin; Si, Shubin; Dui, Hongyan; Cai, Zhiqiang; Sun, Shudong

2014-01-01

Binary decision diagram (BDD) is a graph-based representation of Boolean functions. It is a directed acyclic graph (DAG) based on Shannon's decomposition. Multi-state multi-valued decision diagram (MMDD) is a natural extension of BDD for the symbolic representation and manipulation of the multi-valued logic functions. This paper proposes a decision diagram extension method based on original BDD/MMDD while the scale of a reliability system is extended. Following a discussion of decomposition and physical meaning of BDD and MMDD, the modeling method of BDD/MMDD based on original BDD/MMDD is introduced. Three case studies are implemented to demonstrate the presented methods. Compared with traditional BDD and MMDD generation methods, the decision diagrams extension method is more computationally efficient as shown through the running time

Transitions in pedestrian fundamental diagrams of straight corridors and T-junctions

International Nuclear Information System (INIS)

Zhang, J; Klingsch, W; Schadschneider, A; Seyfried, A

2011-01-01

Many observations of pedestrian dynamics, including various self-organization phenomena, have been reproduced successfully by different models. But the empirical databases for quantitative calibration are still insufficient, e.g. the fundamental diagram as one of the most important relationships displays non-negligible differences among various studies. To improve this situation, experiments in straight corridors and T-junctions are performed. Four different measurement methods are defined to study their effects on the fundamental diagram. It is shown that they have minor influences for ρ −2 but only the Voronoi method is able to resolve the fine structure of the fundamental diagram. This enhanced measurement method permits us to observe the occurrence of a boundary-induced phase transition. For corridors of different widths we found that the specific flow concept works well for ρ −2 . Moreover, we illustrate the discrepancies between the fundamental diagrams of a T-junction and a straight corridor

APPLICATION OF FISHBONE DIAGRAM TO DETERMINE THE RISK OF AN EVENT WITH MULTIPLE CAUSES

OpenAIRE

Gheorghe ILIE; Carmen Nadia CIOCOIU

2010-01-01

Fishbone diagram (also known as Ishikawa diagram) was created with the goal of identifying and grouping the causes which generate a quality problem. Gradually, the method has been used also to group in categories the causes of other types of problems which an organization confronts with. This made Fishbone diagram become a very useful instrument in risk identification stage. The article proposes to extend the applicability of the method by including in the analysis the probabilities and the i...

Including gauge corrections to thermal leptogenesis

International Nuclear Information System (INIS)

Huetig, Janine

2013-01-01

This thesis provides the first approach of a systematic inclusion of gauge corrections to leading order to the ansatz of thermal leptogenesis. We have derived a complete expression for the integrated lepton number matrix including all resummations needed. For this purpose, a new class of diagram has been invented, namely the cylindrical diagram, which allows diverse investigations into the topic of leptogenesis such as the case of resonant leptogenesis. After a brief introduction of the topic of the baryon asymmetry in the universe and a discussion of its most promising solutions as well as their advantages and disadvantages, we have presented our framework of thermal leptogenesis. An effective model was described as well as the associated Feynman rules. The basis for using nonequilibrium quantum field theory has been built in chapter 3. At first, the main definitions have been presented for equilibrium thermal field theory, afterwards we have discussed the Kadanoff-Baym equations for systems out of equilibrium using the example of the Majorana neutrino. The equations have also been solved in the context of leptogenesis in chapter 4. Since gauge corrections play a crucial role throughout this thesis, we have also repeated the naive ansatz by replacing the free equilibrium propagator by propagators including thermal damping rates due to the Standard Model damping widths for lepton and Higgs fields. It is shown that this leads to a comparable result to the solutions of the Boltzmann equations for thermal leptogenesis. Thus it becomes obvious that Standard Model corrections are not negligible for thermal leptogenesis and therefore need to be included systematically from first principles. In order to achieve this we have started discussing the calculation of ladder rung diagrams for Majorana neutrinos using the HTL and the CTL approach in chapter 5. All gauge corrections are included in this framework and thus it has become the basis for the following considerations

Including gauge corrections to thermal leptogenesis

Energy Technology Data Exchange (ETDEWEB)

Huetig, Janine

2013-05-17

This thesis provides the first approach of a systematic inclusion of gauge corrections to leading order to the ansatz of thermal leptogenesis. We have derived a complete expression for the integrated lepton number matrix including all resummations needed. For this purpose, a new class of diagram has been invented, namely the cylindrical diagram, which allows diverse investigations into the topic of leptogenesis such as the case of resonant leptogenesis. After a brief introduction of the topic of the baryon asymmetry in the universe and a discussion of its most promising solutions as well as their advantages and disadvantages, we have presented our framework of thermal leptogenesis. An effective model was described as well as the associated Feynman rules. The basis for using nonequilibrium quantum field theory has been built in chapter 3. At first, the main definitions have been presented for equilibrium thermal field theory, afterwards we have discussed the Kadanoff-Baym equations for systems out of equilibrium using the example of the Majorana neutrino. The equations have also been solved in the context of leptogenesis in chapter 4. Since gauge corrections play a crucial role throughout this thesis, we have also repeated the naive ansatz by replacing the free equilibrium propagator by propagators including thermal damping rates due to the Standard Model damping widths for lepton and Higgs fields. It is shown that this leads to a comparable result to the solutions of the Boltzmann equations for thermal leptogenesis. Thus it becomes obvious that Standard Model corrections are not negligible for thermal leptogenesis and therefore need to be included systematically from first principles. In order to achieve this we have started discussing the calculation of ladder rung diagrams for Majorana neutrinos using the HTL and the CTL approach in chapter 5. All gauge corrections are included in this framework and thus it has become the basis for the following considerations

Scheil-Gulliver Constituent Diagrams

Science.gov (United States)

Pelton, Arthur D.; Eriksson, Gunnar; Bale, Christopher W.

2017-06-01

During solidification of alloys, conditions often approach those of Scheil-Gulliver cooling in which it is assumed that solid phases, once precipitated, remain unchanged. That is, they no longer react with the liquid or with each other. In the case of equilibrium solidification, equilibrium phase diagrams provide a valuable means of visualizing the effects of composition changes upon the final microstructure. In the present study, we propose for the first time the concept of Scheil-Gulliver constituent diagrams which play the same role as that in the case of Scheil-Gulliver cooling. It is shown how these diagrams can be calculated and plotted by the currently available thermodynamic database computing systems that combine Gibbs energy minimization software with large databases of optimized thermodynamic properties of solutions and compounds. Examples calculated using the FactSage system are presented for the Al-Li and Al-Mg-Zn systems, and for the Au-Bi-Sb-Pb system and its binary and ternary subsystems.

Operations space diagram for ECRH and ECCD

DEFF Research Database (Denmark)

Bindslev, H.

2004-01-01

at the design phase. At the operations phase it may also prove useful in setting up experimental scenarios by showing operational possibilities, avoiding the need for survey type ray-tracing at the initial planning stages. The diagram may also serve the purpose of communicating operational possibilities to non......A Clemmov-Mullaly-Allis (CMA) type diagram, the ECW-CMA diagram, for representing the operational possibilities of electron cyclotron heating and current drive (ECRH/ECCD) systems for fusion plasmas is presented. In this diagram, with normalized density and normalized magnetic field coordinates......, the parameter range in which it is possible to achieve a given task (e.g. O-mode current drive for stabilizing a neoclassical tearing mode) appears as a region. With also the Greenwald density limit shown, this diagram condenses the information on operational possibilities, facilitating the overview required...

Penguin-like diagrams from the standard model

International Nuclear Information System (INIS)

Ping, Chia Swee

2015-01-01

The Standard Model is highly successful in describing the interactions of leptons and quarks. There are, however, rare processes that involve higher order effects in electroweak interactions. One specific class of processes is the penguin-like diagram. Such class of diagrams involves the neutral change of quark flavours accompanied by the emission of a gluon (gluon penguin), a photon (photon penguin), a gluon and a photon (gluon-photon penguin), a Z-boson (Z penguin), or a Higgs-boson (Higgs penguin). Such diagrams do not arise at the tree level in the Standard Model. They are, however, induced by one-loop effects. In this paper, we present an exact calculation of the penguin diagram vertices in the ‘tHooft-Feynman gauge. Renormalization of the vertex is effected by a prescription by Chia and Chong which gives an expression for the counter term identical to that obtained by employing Ward-Takahashi identity. The on-shell vertex functions for the penguin diagram vertices are obtained. The various penguin diagram vertex functions are related to one another via Ward-Takahashi identity. From these, a set of relations is obtained connecting the vertex form factors of various penguin diagrams. Explicit expressions for the gluon-photon penguin vertex form factors are obtained, and their contributions to the flavor changing processes estimated

Penguin-like diagrams from the standard model

Energy Technology Data Exchange (ETDEWEB)

Ping, Chia Swee [High Impact Research, University of Malaya, 50603 Kuala Lumpur (Malaysia)

2015-04-24

The Standard Model is highly successful in describing the interactions of leptons and quarks. There are, however, rare processes that involve higher order effects in electroweak interactions. One specific class of processes is the penguin-like diagram. Such class of diagrams involves the neutral change of quark flavours accompanied by the emission of a gluon (gluon penguin), a photon (photon penguin), a gluon and a photon (gluon-photon penguin), a Z-boson (Z penguin), or a Higgs-boson (Higgs penguin). Such diagrams do not arise at the tree level in the Standard Model. They are, however, induced by one-loop effects. In this paper, we present an exact calculation of the penguin diagram vertices in the ‘tHooft-Feynman gauge. Renormalization of the vertex is effected by a prescription by Chia and Chong which gives an expression for the counter term identical to that obtained by employing Ward-Takahashi identity. The on-shell vertex functions for the penguin diagram vertices are obtained. The various penguin diagram vertex functions are related to one another via Ward-Takahashi identity. From these, a set of relations is obtained connecting the vertex form factors of various penguin diagrams. Explicit expressions for the gluon-photon penguin vertex form factors are obtained, and their contributions to the flavor changing processes estimated.

Common phase diagram for low-dimensional superconductors

International Nuclear Information System (INIS)

Michalak, Rudi

2003-01-01

A phenomenological phase diagram which has been derived for high-temperature superconductors from NMR Knight-shift measurements of the pseudogap is compared to the phase diagram that is obtained for organic superconductors and spin-ladder superconductors, both low-dimensional systems. This is contrasted to the phase diagram of some Heavy Fermion superconductors, i.e. superconductors not constrained to a low dimensionality

76 FR 65609 - Safety Zone, Brandon Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago...

Science.gov (United States)

2011-10-24

... Road Lock and Dam to Lake Michigan Including Des Plaines River, Chicago Sanitary and Ship Canal... Lock and Dam to Lake Michigan including Des Plaines River, Chicago Sanitary and Ship Canal, Chicago... INFORMATION: The Coast Guard will enforce a segment of the Safety Zone; Brandon Road Lock and Dam to Lake...

Feynman diagrams without Feynman parameters

International Nuclear Information System (INIS)

Mendels, E.

1978-01-01

Dimensionally regularized Feynman diagrams are represented by means of products of k-functions. The infinite part of these diagrams is found very easily, also if they are overlapping, and the separation of the several kinds of divergences comes out quite naturally. Ward identities are proven in a transparent way. Series expansions in terms of the external momenta and their inner products are possible

Homotopy theory of modules over diagrams of rings

Directory of Open Access Journals (Sweden)

J. P. C. Greenlees

2014-09-01

Full Text Available Given a diagram of rings, one may consider the category of modules over them. We are interested in the homotopy theory of categories of this type: given a suitable diagram of model categories ℳ( (as runs through the diagram, we consider the category of diagrams where the object ( at comes from ℳ(. We develop model structures on such categories of diagrams and Quillen adjunctions that relate categories based on different diagram shapes. Under certain conditions, cellularizations (or right Bousfield localizations of these adjunctions induce Quillen equivalences. As an application we show that a cellularization of a category of modules over a diagram of ring spectra (or differential graded rings is Quillen equivalent to modules over the associated inverse limit of the rings. Another application of the general machinery here is given in work by the authors on algebraic models of rational equivariant spectra. Some of this material originally appeared in the preprint “An algebraic model for rational torus-equivariant stable homotopy theory”, arXiv:1101.2511, but has been generalized here.

The application of diagrams in architectural design

Directory of Open Access Journals (Sweden)

Dulić Olivera

2014-01-01

Full Text Available Diagrams in architecture represent the visualization of the thinking process, or selective abstraction of concepts or ideas translated into the form of drawings. In addition, they provide insight into the way of thinking about and in architecture, thus creating a balance between the visual and the conceptual. The subject of research presented in this paper are diagrams as a specific kind of architectural representation, and possibilities and importance of their application in the design process. Diagrams are almost old as architecture itself, and they are an element of some of the most important studies of architecture during all periods of history - which results in a large number of different definitions of diagrams, but also very different conceptualizations of their features, functions and applications. The diagrams become part of contemporary architectural discourse during the eighties and nineties of the twentieth century, especially through the work of architects like Bernard Tschumi, Peter Eisenman, Rem Koolhaas, SANAA and others. The use of diagrams in the design process allows unification of some of the essential aspects of the profession: architectural representation and design process, as well as the question of the concept of architectural and urban design at a time of rapid changes at all levels of contemporary society. The aim of the research is the analysis of the diagram as a specific medium for processing large amounts of information that the architect should consider and incorporate into the architectural work. On that basis, it is assumed that an architectural diagram allows the creator the identification and analysis of specific elements or ideas of physical form, thereby constantly maintaining concept of the integrity of the architectural work.

Reading fitness landscape diagrams through HSAB concepts

Energy Technology Data Exchange (ETDEWEB)

Vigneresse, Jean-Louis, E-mail: jean-louis.vigneresse@univ-lorraine.fr

2014-10-31

Highlights: • Qualitative information from HSAB descriptors. • 2D–3D diagrams using chemical descriptors (χ, η, ω, α) and principles (MHP, mEP, mPP). • Estimate of the energy exchange during reaction paths. • Examples from complex systems (geochemistry). - Abstract: Fitness landscapes are conceived as range of mountains, with local peaks and valleys. In terms of potential, such topographic variations indicate places of local instability or stability. The chemical potential, or electronegativity, its value changed of sign, carries similar information. In addition to chemical descriptors defined through hard-soft acid-base (HSAB) concepts and computed through density functional theory (DFT), the principles that rule chemical reactions allow the design of such landscape diagrams. The simplest diagram uses electrophilicity and hardness as coordinates. It allows examining the influence of maximum hardness or minimum electrophilicity principles. A third dimension is introduced within such a diagram by mapping the topography of electronegativity, polarizability or charge exchange. Introducing charge exchange during chemical reactions, or mapping a third parameter (f.i. polarizability) reinforces the information carried by a simple binary diagram. Examples of such diagrams are provided, using data from Earth Sciences, simple oxides or ligands.

Adaptive Diagrams: Handing Control over to the Learner to Manage Split-Attention Online

Science.gov (United States)

Agostinho, Shirley; Tindall-Ford, Sharon; Roodenrys, Kylie

2013-01-01

Based on cognitive load theory, it is well known that when studying a diagram that includes explanatory text, optimal learning occurs when the text is physically positioned close to the diagram as it eliminates the need for learners to split their attention between the two sources of information. What is not known is the effect on learning when…

Selected topics on the nonrelativistic diagram technique

International Nuclear Information System (INIS)

Blokhintsev, L.D.; Narodetskij, I.M.

1983-01-01

The construction of the diagrams describing various processes in the four-particle systems is considered. It is shown that these diagrams, in particular the diagrams corresponding to the simple mechanisms often used in nuclear and atomic reaction theory, are readily obtained from the Faddeev-Yakubovsky equations. The covariant four-dimensional formalism of nonrelativistic Feynman graphs and its connection to the three-dimensional graph technique are briefly discussed

Drawing Euler Diagrams with Circles: The Theory of Piercings.

Science.gov (United States)

Stapleton, Gem; Leishi Zhang; Howse, John; Rodgers, Peter

2011-07-01

Euler diagrams are effective tools for visualizing set intersections. They have a large number of application areas ranging from statistical data analysis to software engineering. However, the automated generation of Euler diagrams has never been easy: given an abstract description of a required Euler diagram, it is computationally expensive to generate the diagram. Moreover, the generated diagrams represent sets by polygons, sometimes with quite irregular shapes that make the diagrams less comprehensible. In this paper, we address these two issues by developing the theory of piercings, where we define single piercing curves and double piercing curves. We prove that if a diagram can be built inductively by successively adding piercing curves under certain constraints, then it can be drawn with circles, which are more esthetically pleasing than arbitrary polygons. The theory of piercings is developed at the abstract level. In addition, we present a Java implementation that, given an inductively pierced abstract description, generates an Euler diagram consisting only of circles within polynomial time.

Multi-currency Influence Diagrams

DEFF Research Database (Denmark)

Nielsen, Søren Holbech; Nielsen, Thomas Dyhre; Jensen, Finn V.

2007-01-01

When using the influence diagrams framework for solving a decision problem with several different quantitative utilities, the traditional approach has been to convert the utilities into one common currency. This conversion is carried out using a tacit transformation, under the assumption...... that the converted problem is equivalent to the original one. In this paper we present an extension of the influence diagram framework. The extension allows for these decision problems to be modelled in their original form. We present an algorithm that, given a linear conversion function between the currencies...

Phase stabilities at a glance: Stability diagrams of nickel dipnictides

International Nuclear Information System (INIS)

Bachhuber, F.; Rothballer, J.; Weihrich, R.; Söhnel, T.

2013-01-01

In the course of the recent advances in chemical structure prediction, a straightforward type of diagram to evaluate phase stabilities is presented based on an expedient example. Crystal structures and energetic stabilities of dipnictides NiPn 2 (Pn = N, P, As, Sb, Bi) are systematically investigated by first principles calculations within the framework of density functional theory using the generalized gradient approximation to treat exchange and correlation. These dipnictides show remarkable polymorphism that is not yet understood systematically and offers room for the discovery of new phases. Relationships between the concerned structures including the marcasite, the pyrite, the arsenopyrite/CoSb 2 , and the NiAs 2 types are highlighted by means of common structural fragments. Electronic stabilities of experimentally known and related AB 2 structure types are presented graphically in so-called stability diagrams. Additionally, competing binary phases are taken into consideration in the diagrams to evaluate the stabilities of the title compounds with respect to decomposition. The main purpose of the stability diagrams is the introduction of an image that enables the estimation of phase stabilities at a single glance. Beyond that, some of the energetically favored structure types can be identified as potential new phases

Students’ learning activities while studying biological process diagrams

NARCIS (Netherlands)

Kragten, M.; Admiraal, W.; Rijlaarsdam, G.

2015-01-01

Process diagrams describe how a system functions (e.g. photosynthesis) and are an important type of representation in Biology education. In the present study, we examined students’ learning activities while studying process diagrams, related to their resulting comprehension of these diagrams. Each

Tight-binding calculation of Ti-Rh--type phase diagram

International Nuclear Information System (INIS)

Sluiter, M.; Turchi, P.; Fu Zezhong; de Fontaine, D.

1988-01-01

Tight-binding electronic band-structure calculations were combined with a free-energy expression from a statistical mechanical method called the cluster-variation method. The effective pair interactions used in the cluster-variation calculation were evaluated by the generalized perturbation method. Only d orbitals were included and the numbers of d electrons per atom were taken to be three for the pure A element and eight for the pure B. A phase diagram was constructed incorporating, for the first time, both fcc and bcc lattices and their simple-ordered superstructures. The calculated diagram agreed reasonably well with those determined empirically for Ti-Rh or Ti-Ir

Multicritical phase diagrams of the Blume-Emery-Griffiths model with repulsive biquadratic coupling including metastable phases: the pair approximation and the path probability method with pair distribution

International Nuclear Information System (INIS)

Keskin, Mustafa; Erdinc, Ahmet

2004-01-01

As a continuation of the previously published work, the pair approximation of the cluster variation method is applied to study the temperature dependences of the order parameters of the Blume-Emery-Griffiths model with repulsive biquadratic coupling on a body centered cubic lattice. We obtain metastable and unstable branches of the order parameters besides the stable branches and phase transitions of these branches are investigated extensively. We study the dynamics of the model by the path probability method with pair distribution in order to make sure that we find and define the metastable and unstable branches of the order parameters completely and correctly. We present the metastable phase diagram in addition to the equilibrium phase diagram and also the first-order phase transition line for the unstable branches of the quadrupole order parameter is superimposed on the phase diagrams. It is found that the metastable phase diagram and the first-order phase boundary for the unstable quadrupole order parameter always exist at the low temperatures which are consistent with experimental and theoretical works

Operations space diagram for ECRH and ECCD

International Nuclear Information System (INIS)

Bindslev, Henrik

2004-01-01

A Clemmov-Mullaly-Allis (CMA) type diagram, the ECW-CMA diagram, for representing the operational possibilities of electron cyclotron heating and current drive (ECRH/ECCD) systems for fusion plasmas is presented. In this diagram, with normalized density and normalized magnetic field coordinates, the parameter range in which it is possible to achieve a given task (e.g. O-mode current drive for stabilizing a neoclassical tearing mode) appears as a region. With also the Greenwald density limit shown, this diagram condenses the information on operational possibilities, facilitating the overview required at the design phase. At the operations phase it may also prove useful in setting up experimental scenarios by showing operational possibilities, avoiding the need for survey type ray-tracing at the initial planning stages. The diagram may also serve the purpose of communicating operational possibilities to non-experts. JET and ITER like plasmas are used, but the method is generic. (author)

Safety-barrier diagrams as a safety management tool

DEFF Research Database (Denmark)

Duijm, Nijs Jan

2009-01-01

Safety-barrier diagrams and “bow-tie” diagrams have become popular methods in risk analysis and safety management. This paper describes the syntax and principles for constructing consistent and valid safety-barrier diagrams. The latter's relation to other methods such as fault trees and Bayesian...

Near threshold expansion of Feynman diagrams

International Nuclear Information System (INIS)

Mendels, E.

2005-01-01

The near threshold expansion of Feynman diagrams is derived from their configuration space representation, by performing all x integrations. The general scalar Feynman diagram is considered, with an arbitrary number of external momenta, an arbitrary number of internal lines and an arbitrary number of loops, in n dimensions and all masses may be different. The expansions are considered both below and above threshold. Rules, giving real and imaginary part, are derived. Unitarity of a sunset diagram with I internal lines is checked in a direct way by showing that its imaginary part is equal to the phase space integral of I particles

On the question of calculation methods of phase diagrams

International Nuclear Information System (INIS)

Vasil'ev, M.V.

1983-01-01

The technique of determining interaction parameters of components of binary alloys is suggested. U-Mo and Cu-Al systems are used as example with the aid of experimental state diagrams. It is shown that the search for new regularities is necessary with the aim of analytical description of state diagrams and forecast of the shape of phase equilibria curves in real systems. Optimum combinations of experimental investigations with the aim of reliable determination of supporting points and forecasting possibilities of typical equations can considerably decrease the volume of experimental work when preparing state diagrams, in cases of repeated state diagrams of more reliable state diagrams with the application of more advanced methods of investigation. The translation of state diagrams from geometric to analytical language with the use of typical equations opens up new possibilities for establishing a compact information bank for state diagrams

A geometric proof of confluence by decreasing diagrams

NARCIS (Netherlands)

Klop, J.W.; Oostrom, V. van; Vrijer, R. de

The criterion for confluence using decreasing diagrams is a generalization of several well-known confluence criteria in abstract rewriting, such as the strong confluence lemma. We give a new proof of the decreasing diagram theorem based on a geometric study of in finite reduction diagrams, arising

Welding metallurgy of SA508 Cl II heat affected zones

International Nuclear Information System (INIS)

Alberry, P.J.; Lambert, J.A.

1982-01-01

A weld thermal simulation technique has been used to investigate the metallurgical response of SA508 class II material during welding. Dynamic Ac 1 and Ac 3 data, grain growth kinetics and continuous cooling transformation diagrams have been measured. The heat affected zone structure, grain size and precipitate distribution are described in terms of the weld thermal cycle experienced and compared with a weld heat affected zone. The as-welded hardness and tempering response of a range of possible heat affected zone structures has been established. The tempering effects of various weld thermal cycles are calculated from isothermal tempering data. The likely tempering effects during welding are estimated and compared with the tempering of actual welds during welding and in subsequent conventional post weld heat treatment. 16 figures, 6 tables

Compact flow diagrams for state sequences

NARCIS (Netherlands)

Buchin, K.A.; Buchin, M.E.; Gudmundsson, J.; Horton, M.J.; Sijben, S.

2016-01-01

We introduce the concept of compactly representing a large number of state sequences, e.g., sequences of activities, as a flow diagram. We argue that the flow diagram representation gives an intuitive summary that allows the user to detect patterns among large sets of state sequences. Simplified,

The role of perceptual cues in matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; van Amelsvoort, Marije; Anjewierden, A.

An experiment was conducted to assess whether the design of a matrix diagram influences how people study the diagram and whether this has an effect on recall of the presented information. We compared four versions of a matrix diagram on antisocial personality disorder. It consisted of four header

The role of perceptual cues in matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; Amelsvoort, Marije; Anjewierden, Anjo Allert

2015-01-01

An experiment was conducted to assess whether the design of a matrix diagram influences how people study the diagram and whether this has an effect on recall of the presented information. We compared four versions of a matrix diagram on antisocial personality disorder. It consisted of four header

Compact flow diagrams for state sequences

NARCIS (Netherlands)

Buchin, Kevin; Buchin, Maike; Gudmundsson, Joachim; Horton, Michael; Sijben, Stef

2017-01-01

We introduce the concept of using a flow diagram to compactly represent the segmentation of a large number of state sequences according to a set of criteria. We argue that this flow diagram representation gives an intuitive summary that allows the user to detect patterns within the segmentations. In

Diagrams of natural deductions

Energy Technology Data Exchange (ETDEWEB)

Popov, S V

1982-01-01

The concept of natural deductions was investigated by the author in his analysis of the complexity of deductions in propositional computations (1975). Here some natural deduction systems are considered, and an analytical procedure proposed which results in a deduction diagram for each system. Each diagram takes the form of an orientated, charge graph, features of which can be used to establish the equivalence of classes of deductions. For each of the natural deduction systems considered, a system of equivalent transformation schemes is derived, which is complete with respect to the given definition of equivalence. 2 references.

Control wiring diagrams

International Nuclear Information System (INIS)

McCauley, T.M.; Eskinazi, M.; Henson, L.L.

1989-01-01

This paper discusses the changes in electrical document requirements that occur when construction is complete and a generating station starts commercial operation. The needs of operations and maintenance (O and M) personnel are analyzed and contrasted with those of construction to illustrate areas in which the construction documents (drawings, diagrams, and databases) are difficult to use for work at an operating station. The paper discusses the O and M electrical documents that the Arizona Nuclear Power Project (ANPP) believes are most beneficial for the three operating units at Palo Verde; these are control wiring diagrams and an associated document cross-reference list. The benefits offered by these new, station O and M-oriented documents are weighted against the cost of their creation and their impact on drawing maintenance

New detectors for powders diagrams

International Nuclear Information System (INIS)

Convert, P.

1975-01-01

During the last few years, all the classical neutron diffractometers for powders have used one or maybe a few counters. So, it takes a long time to obtain a diagram which causes many disadvantages: 1) very long experiments: one or two days (or flux on the sample about 10 6 n/cm 2 /a); 2) necessity of big samples: many cm 3 ; 3) necessity of having the whole diagram before changing anything in the experiment: magnetic field, temperature, quality of the sample; 4) necessity of having collimators of a few times ten minutes to obtain correct statistics in the diagram. Because of these disadvantages, several attempts have been made to speed up the experimental procedure such as using more counters, the detection of neutrons on a resistive wire, etc. In Grenoble, new position-sensitive detectors have been constructed using a digital technique

Causal Diagrams for Empirical Research

OpenAIRE

Pearl, Judea

1994-01-01

The primary aim of this paper is to show how graphical models can be used as a mathematical language for integrating statistical and subject-matter information. In particular, the paper develops a principled, nonparametric framework for causal inference, in which diagrams are queried to determine if the assumptions available are sufficient for identifiying causal effects from non-experimental data. If so the diagrams can be queried to produce mathematical expressions for causal effects in ter...

Graphical matching rules for cardinality based service feature diagrams

Directory of Open Access Journals (Sweden)

Faiza Kanwal

2017-03-01

Full Text Available To provide efficient services to end-users, variability and commonality among the features of the product line is a challenge for industrialist and researchers. Feature modeling provides great services to deal with variability and commonality among the features of product line. Cardinality based service feature diagrams changed the basic framework of service feature diagrams by putting constraints to them, which make service specifications more flexible, but apart from their variation in selection third party services may have to be customizable. Although to control variability, cardinality based service feature diagrams provide high level visual notations. For specifying variability, the use of cardinality based service feature diagrams raises the problem of matching a required feature diagram against the set of provided diagrams.

The shape of a strain-based failure assessment diagram

International Nuclear Information System (INIS)

Budden, P.J.; Ainsworth, R.A.

2012-01-01

There have been a number of recent developments of strain-based fracture assessment approaches, including proposals by Budden [Engng Frac Mech 2006;73:537–52] for a strain-based failure assessment diagram (FAD) related to the conventional stress-based FAD. However, recent comparisons with finite element (FE) data have shown that this proposed strain-based FAD can be non-conservative in some cases, particularly for deeper cracks and materials with little strain-hardening capacity. Therefore, this paper re-examines the shape of the strain-based FAD, guided by these FE analyses and some theoretical analysis. On this basis, modified proposals for the shape of the strain-based FAD are given, including simplified and more detailed options in line with the options available for stress-based FADs in existing fitness-for-service procedures. The proposals are then illustrated by a worked example and by comparison with FE data, which demonstrate that the new proposals are generally conservative. - Highlights: ► The strain-based failure assessment diagram approach to fracture is developed. ► The new approach modifies earlier proposals by Budden. ► A new generic Option 1 strain-based failure assessment diagram is proposed. ► Validation based on finite element J data for plates and cylinders is presented. ► The new approach is generally conservative compared with the finite element data.

Diagramming Transactive Building Business Cases: Using Principles of e3 Value to Document Valuation Studies

Energy Technology Data Exchange (ETDEWEB)

Hammerstrom, Donald J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Makhmalbaf, Atefe [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Marinovici, Maria C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-12-30

Energy management in buildings is becoming more transactive. Pacific Northwest National Laboratory and the U.S. Department of Energy Building Technologies Office recently defined innovative use cases wherein market-like mechanisms are used to manage energy within buildings, between buildings, and between buildings and third-party entities, such as power utilities. A next step toward defining a set of transactive use cases in the buildings domain is to carefully diagram the corresponding business cases to capture details of transactions among all stakeholders and their economic value propositions. The principles of e3-value diagramming are applied in this report toward creating business value diagrams. These principles are extended to be consistent with Universal Modeling Language use-case diagrams. Example diagrams are presented for a subset of buildings-domain use cases that were introduced in an earlier Pacific Northwest National Laboratory report. The diagrams are intended to clearly represent an understanding of the transactions through which individual entities accumulate value in their respective use cases, and the diagrams should therefore support economic valuation studies. The report reviews some of the foundational principles of e3 value and includes authors’ insights concerning the formulation of these diagrams using Universal Modeling Language as a more systematic modeling approach.

Equations of State and Phase Diagrams of Ammonia

Science.gov (United States)

Glasser, Leslie

2009-01-01

We present equations of state relating the phases and a three-dimensional phase diagram for ammonia with its solid, liquid, and vapor phases, based on fitted authentic experimental data and including recent information on the high-pressure solid phases. This presentation follows similar articles on carbon dioxide and water published in this…

On the Impact of Layout Quality to Understanding UML Diagrams: Diagram Type and Expertise

DEFF Research Database (Denmark)

Störrle, Harald

2012-01-01

Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only. In the ......Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only...

JaxoDraw: A graphical user interface for drawing Feynman diagrams

Science.gov (United States)

Binosi, D.; Theußl, L.

2004-08-01

JaxoDraw is a Feynman graph plotting tool written in Java. It has a complete graphical user interface that allows all actions to be carried out via mouse click-and-drag operations in a WYSIWYG fashion. Graphs may be exported to postscript/EPS format and can be saved in XML files to be used for later sessions. One of JaxoDraw's main features is the possibility to create ? code that may be used to generate graphics output, thus combining the powers of ? with those of a modern day drawing program. With JaxoDraw it becomes possible to draw even complicated Feynman diagrams with just a few mouse clicks, without the knowledge of any programming language. Program summaryTitle of program: JaxoDraw Catalogue identifier: ADUA Program summary URL:http://cpc.cs.qub.ac.uk/summaries/ADUA Program obtainable from: CPC Program Library, Queen's University of Belfast, N. Ireland Distribution format: tar gzip file Operating system: Any Java-enabled platform, tested on Linux, Windows ME, XP, Mac OS X Programming language used: Java License: GPL Nature of problem: Existing methods for drawing Feynman diagrams usually require some 'hard-coding' in one or the other programming or scripting language. It is not very convenient and often time consuming, to generate relatively simple diagrams. Method of solution: A program is provided that allows for the interactive drawing of Feynman diagrams with a graphical user interface. The program is easy to learn and use, produces high quality output in several formats and runs on any operating system where a Java Runtime Environment is available. Number of bytes in distributed program, including test data: 2 117 863 Number of lines in distributed program, including test data: 60 000 Restrictions: Certain operations (like internal latex compilation, Postscript preview) require the execution of external commands that might not work on untested operating systems. Typical running time: As an interactive program, the running time depends on the complexity

Quest for the QCD phase diagram in extreme environments

Energy Technology Data Exchange (ETDEWEB)

Fukushima, Kenji, E-mail: fuku@rk.phys.keio.ac.jp [Keio University, Department of Physics (Japan)

2013-03-15

We review the state-of-the-art status of the research on the phase diagram of QCD matter out of quarks and gluons. Our discussions particularly include the extreme environments such as the high temperature, the high baryon density, and the strong magnetic field.

Beyond Feynman Diagrams (1/3)

CERN Multimedia

CERN. Geneva

2013-01-01

For decades the central theoretical tool for computing scattering amplitudes has been the Feynman diagram. However, Feynman diagrams are just too slow, even on fast computers, to be able to go beyond the leading order in QCD, for complicated events with many jets of hadrons in the final state. Such events are produced copiously at the LHC, and constitute formidable backgrounds to many searches for new physics. Over the past few years, alternative methods that go beyond ...

Wind Diagrams in Medieval Iceland

DEFF Research Database (Denmark)

Kedwards, Dale

2014-01-01

This article presents a study of the sole wind diagram that survives from medieval Iceland, preserved in the encyclopaedic miscellany in Copenhagen's Arnamagnæan Institute with the shelf mark AM 732b 4to (c. 1300-25). It examines the wind diagram and its accompanying text, an excerpt on the winds...... from Isidore of Seville's Etymologies. It also examines the perimeter of winds on two medieval Icelandic world maps, and the visual traditions from which they draw....

Bayesian Networks and Influence Diagrams

DEFF Research Database (Denmark)

Kjærulff, Uffe Bro; Madsen, Anders Læsø

 Probabilistic networks, also known as Bayesian networks and influence diagrams, have become one of the most promising technologies in the area of applied artificial intelligence, offering intuitive, efficient, and reliable methods for diagnosis, prediction, decision making, classification......, troubleshooting, and data mining under uncertainty. Bayesian Networks and Influence Diagrams: A Guide to Construction and Analysis provides a comprehensive guide for practitioners who wish to understand, construct, and analyze intelligent systems for decision support based on probabilistic networks. Intended...

Proof test diagrams for Zerodur glass-ceramic

Science.gov (United States)

Tucker, D. S.

1991-01-01

Proof test diagrams for Zerodur glass-ceramics are calculated from available fracture mechanics data. It is shown that the environment has a large effect on minimum time-to-failure as predicted by proof test diagrams.

Soft zone formation in dissimilar welds between two Cr-Mo steels

International Nuclear Information System (INIS)

Albert, S.K.; Gill, T.P.S.; Tyagi, A.K.; Mannan, S.L.; Rodriguez, P.; Kulkarni, S.D.

1997-01-01

Two dissimilar weldments between 9Cr-1Mo and 2.25Cr-1Mo ferritic steels have been characterized for their microstructural stability during various postweld heat treatments (PWHTs). The samples for the investigation were extracted from bead-on-plate weldments made by depositing 2.25Cr-1Mo weld metal on 9Cr-1Mo base plate and vice versa. Subsequent application of PWHT resulted in the formation of a soft zone in the low Cr ferritic steel weld or base plate. A carbide-rich hard zone, adjoining the soft zone, was also detected in the high Cr side of the weldment. Unmixed zones in the weld metal provided additional soft and hard zones in the weld metals. The migration of carbon from low-Cr steel to high-Cr steel, driven by the carbon activity gradient, has been shown to be responsible for the formation of soft and hard zones. A carbon activity diagram for 2.25Cr-1Mo/9Cr-1Mo weldments has been proposed to aid in the selection of welding consumables for reducing or preventing the soft zone formation

Atlas of hot isostatic beryllium powder pressing diagrams

International Nuclear Information System (INIS)

Stoev, P.I.; Papirov, I.I.; Tikhinskij, G.F.; Vasil'ev, A.A.

1995-01-01

Diagrams of hot isotopic pressing (HIP) of beryllium powder with different grain size in a wide range of pressing parameters are built by mathematical modeling methods. The HIP diagrams presented are divided into 3 groups: parametric dependencies D=f(P,T); technological HIP diagrams; compacting mechanisms. The created data bank permits to optimise beryllium powder HIP with changing parameters. 4 refs., 23 figs

Visualizing Metrics on Areas of Interest in Software Architecture Diagrams

NARCIS (Netherlands)

Byelas, Heorhiy; Telea, Alexandru; Eades, P; Ertl, T; Shen, HW

2009-01-01

We present a new method for the combined visualization of software architecture diagrams, Such as UML class diagrams or component diagrams, and software metrics defined on groups of diagram elements. Our method extends an existing rendering technique for the so-called areas of interest in system

Updating the Nomographical Diagrams for Dimensioning the Beams

Directory of Open Access Journals (Sweden)

Pop Maria T.

2015-12-01

Full Text Available In order to reduce the time period needed for structures design it is strongly recommended to use nomographical diagrams. The base for formation and updating the nomographical diagrams, stands on the charts presented by different technical publications. The updated charts use the same algorithm and calculation elements as the former diagrams in accordance to the latest prescriptions and European standards. The result consists in a chart, having the same properties, similar with the nomogragraphical diagrams already in us. As a general conclusion, even in our days, the nomographical diagrams are very easy to use. Taking into consideration the value of the moment it’s easy to find out the necessary reinforcement area and vice-verse, having the reinforcement area you can find out the capable moment. It still remains a useful opportunity for pre-sizing and designs the reinforced concrete sections.

Phase diagram of classical electronic bilayers

International Nuclear Information System (INIS)

Ranganathan, S; Johnson, R E

2006-01-01

Extensive molecular dynamics calculations have been performed on classical, symmetric electronic bilayers at various values of the coupling strength Γ and interlayer separation d to delineate its phase diagram in the Γ-d plane. We studied the diffusion, the amplitude of the main peak of the intralayer static structure factor and the peak positions of the intralayer pair correlation function with the aim of defining equivalent signatures of freezing and constructing the resulting phase diagram. It is found that for Γ greater than 75, crystalline structures exist for a certain range of interlayer separations, while liquid phases are favoured at smaller and larger d. It is seen that there is good agreement between our phase diagram and previously published ones

Phase diagram of classical electronic bilayers

Energy Technology Data Exchange (ETDEWEB)

Ranganathan, S [Department of Physics, Royal Military College of Canada, Kingston, Ontario K7K 7B4 (Canada); Johnson, R E [Department of Mathematics and Computer Science, Royal Military College of Canada, Kingston, Ontario K7K 7B4 (Canada)

2006-04-28

Extensive molecular dynamics calculations have been performed on classical, symmetric electronic bilayers at various values of the coupling strength {gamma} and interlayer separation d to delineate its phase diagram in the {gamma}-d plane. We studied the diffusion, the amplitude of the main peak of the intralayer static structure factor and the peak positions of the intralayer pair correlation function with the aim of defining equivalent signatures of freezing and constructing the resulting phase diagram. It is found that for {gamma} greater than 75, crystalline structures exist for a certain range of interlayer separations, while liquid phases are favoured at smaller and larger d. It is seen that there is good agreement between our phase diagram and previously published ones.

Use of Fault Displacement Vector to Identify Future Zones of Seismicity: An Example from the Earthquakes of Nepal Himalayas.

Science.gov (United States)

Naim, F.; Mukherjee, M. K.

2017-12-01

Earthquakes occur due to fault slip in the subsurface. They can occur either as interplate or intraplate earthquakes. The region of study is the Nepal Himalayas that defines the boundary of Indian-Eurasian plate and houses the focus of the most devastating earthquakes. The aim of the study was to analyze all the earthquakes that occurred in the Nepal Himalayas upto May 12, 2015 earthquake in order to mark the regions still under stress and vulnerable for future earthquakes. Three different fault systems in the Nepal Himalayas define the tectonic set up of the area. They are: (1) Main Frontal Thrust(MFT), (2) Main Central Thrust(MCT) and (3) Main Boundary Thrust(MBT) that extend from NW to SE. Most of the earthquakes were observed to occur between the MBT and MCT. Since the thrust faults are dipping towards NE, the focus of most of the earthquakes lies on the MBT. The methodology includes estimating the dip of the fault by considering the depths of different earthquake events and their corresponding distance from the MBT. In order to carry out stress analysis on the fault, the beach ball diagrams associated with the different earthquakes were plotted on a map. Earthquakes in the NW and central region of the fault zone were associated with reverse fault slip while that on the South-Eastern part were associated with a strike slip component. The direction of net slip on the fault associated with the different earthquakes was known and from this a 3D slip diagram of the fault was constructed. The regions vulnerable for future earthquakes in the Nepal Himalaya were demarcated on the 3D slip diagram of the fault. Such zones were marked owing to the fact that the slips due to earthquakes cause the adjoining areas to come under immense stress and this stress is directly proportional to the amount of slip occuring on the fault. These vulnerable zones were in turn projected on the map to show their position and are predicted to contain the epicenter of the future earthquakes.

Common Pb isotope mapping of UHP metamorphic zones in Dabie orogen, Central China: Implication for Pb isotopic structure of subducted continental crust

Science.gov (United States)

Shen, Ji; Wang, Ying; Li, Shu-Guang

2014-10-01

We report Pb isotopic compositions for feldspars separated from 57 orthogneisses and 2 paragneisses from three exhumed UHPM slices representing the North Dabie zone, the Central Dabie zone and the South Dabie zone of the Dabie orogen, central-east China. The feldspars from the gneisses were recrystallized during Triassic continental subduction and UHP metamorphism. Precursors of the orthogneisses are products of Neoproterozoic bimodal magmatic events, those in north Dabie zone emplaced into the lower crust and those in central and south Dabie zones into middle or upper crust, respectively. On a 207Pb/204Pb vs. 206Pb/204Pb diagram, almost all orthogneisses data lie to the left of the 0.23 Ga paleogeochron and plot along the model mantle evolution curve with the major portion of the data plotting below it. On a 208Pb/204Pb vs. 206Pb/204Pb diagram the most of data of north Dabie zone extend in elongate arrays along the lower crustal curve and others extend between the lower crustal curve to near the mantle evolution curve for the plumbotectonics model. This pattern demonstrates that the Pb isotopic evolution of the feldspars essentially ended at 0.23 Ga and the orthogneiss protoliths were principally dominated by reworking of ancient lower crust with some addition of juvenile mantle in the Neoproterozoic rifting tectonic zone. According to geological evolution history of the locally Dabie orogen, a four-stage Pb isotope evolution model including a long time evolution between 2.0 and 0.8 Ga with a lower crust type U/Pb ratio (μ = 5-6) suggests that magmatic emplacement levels of the protoliths of the orthogneisses in the Dabie orogen at 0.8 Ga also play an important role in the Pb evolution of the exhumed UHPM slices, corresponding to their respective Pb characters at ca. 0.8-0.23 Ga. For example, north Dabie zone requires low μ values (3.4-9.6), while central and south Dabie zones require high μ values (10.9-17.2). On the other hand, Pb isotopic mixing between

Modeling cancer registration processes with an enhanced activity diagram.

Science.gov (United States)

Lyalin, D; Williams, W

2005-01-01

Adequate instruments are needed to reflect the complexity of routine cancer registry operations properly in a business model. The activity diagram is a key instrument of the Unified Modeling Language (UML) for the modeling of business processes. The authors aim to improve descriptions of processes in cancer registration, as well as in other public health domains, through the enhancements of an activity diagram notation within the standard semantics of UML. The authors introduced the practical approach to enhance a conventional UML activity diagram, complementing it with the following business process concepts: timeline, duration for individual activities, responsibilities for individual activities within swimlanes, and descriptive text. The authors used an enhanced activity diagram for modeling surveillance processes in the cancer registration domain. Specific example illustrates the use of an enhanced activity diagram to visualize a process of linking cancer registry records with external mortality files. Enhanced activity diagram allows for the addition of more business concepts to a single diagram and can improve descriptions of processes in cancer registration, as well as in other domains. Additional features of an enhanced activity diagram allow to advance the visualization of cancer registration processes. That, in turn, promotes the clarification of issues related to the process timeline, responsibilities for particular operations, and collaborations among process participants. Our first experiences in a cancer registry best practices development workshop setting support the usefulness of such an approach.

CONSTRUCTIVE MODELLING FOR ZONE OF RECOVERY ENERGY DISTRIBUTION OF DC TRACTION

Directory of Open Access Journals (Sweden)

V. I. Shynkarenko

2016-10-01

Full Text Available Purpose.The article is aimed to develop the means and methods of forming a plurality of real and potential structural diagrams for zones of energy recovery and different locations of trains for further training neuro-fuzzy networks on the basis of expert solutions and also for the formation of good control. Methodology. Methodology of mathematical and algorithmic constructivism for modeling the structural diagrams of the electric supply system and modes of traction power consumption and the train’s locations in zones of energy recovery was applied. This approach involves the development of constructive-synthesizing structures (CSS with transformation by specialization, interpretation, specification and implementation. Development CSS provides an extensible definition media, relations and the signature of operations and constructive axiomatic. The most complex and essential part of the axioms is the set formed by the substitution rules defining the process of withdrawal of the corresponding structures. Findings. A specialized and specified CSS, which allows considering all the possibilities and features, that supply power traction systems with modern equipment, stations and trains location was designed. Its feature: the semantic content of the terminal alphabet images of electrical traction network and power consumers with relevant attributes. A special case of the formation of the structural diagram shows the possibilities CSS in relation to this problem. Originality. A new approach to solving the problem of rational use of energy recovery, which consists in application of the methods and means of artificial neural networks, expert systems, fuzzy logic and mathematical and algorithmic constructivism. This paper presents the methods of constructive simulation of a production-distribution of energy recovery zone structure in the system of the DC traction. Practical value. The tasks decision of the rational use of energy recovery can

Fishbone Diagrams: Organize Reading Content with a "Bare Bones" Strategy

Science.gov (United States)

Clary, Renee; Wandersee, James

2010-01-01

Fishbone diagrams, also known as Ishikawa diagrams or cause-and-effect diagrams, are one of the many problem-solving tools created by Dr. Kaoru Ishikawa, a University of Tokyo professor. Part of the brilliance of Ishikawa's idea resides in the simplicity and practicality of the diagram's basic model--a fish's skeleton. This article describes how…

Phase diagram of the ABC model with nonconserving processes

International Nuclear Information System (INIS)

Lederhendler, A; Cohen, O; Mukamel, D

2010-01-01

The three species ABC model of driven particles on a ring is generalized to include vacancies and particle-nonconserving processes. The model exhibits phase separation at high densities. For equal average densities of the three species, it is shown that although the dynamics is local, it obeys detailed balance with respect to a Hamiltonian with long-range interactions, yielding a nonadditive free energy. The phase diagrams of the conserving and nonconserving models, corresponding to the canonical and grand-canonical ensembles, respectively, are calculated in the thermodynamic limit. Both models exhibit a transition from a homogeneous to a phase-separated state, although the phase diagrams are shown to differ from each other. This conforms with the expected inequivalence of ensembles in equilibrium systems with long-range interactions. These results are based on a stability analysis of the homogeneous phase and exact solution of the continuum equations of the models. They are supported by Monte Carlo simulations. This study may serve as a useful starting point for analyzing the phase diagram for unequal densities, where detailed balance is not satisfied and thus a Hamiltonian cannot be defined

Muonium and the Breit-Rabi diagram

International Nuclear Information System (INIS)

Cox, S.F.J.

1984-01-01

This chapter introduces the study of muonium, as opposed to that of unbound muons. The properties and behaviour of muonium are compared and contrasted with those of hydrogen and of positronium. The special significance of muonium in atomic and molecular physics is explained, and its utility as a lightweight or radioactive isotope of hydrogen in solid state physics and chemistry illustrated. The identification of atomic muonium by means of its ground state magnetic properties is described with reference to the Breit-Rabi diagram. This diagram is invaluable for interpreting or predicting MuSR observations, both in transverse and longitudinal magnetic fields, so its construction and properties are explained in some detail. The precession signals observed in transverse-field MuSR correspond to transitions allowed between the energy levels in this diagram; particular attention is paid to the spectra characteristic of the high and low field regimes. The different states of muonium observed in dielectric, semiconducting and metallic materials are introduced. The influence of the host medium on the spectral parameters, hyperfine interaction and linewidth, is considered both for atomic muonium and for muonium which is chemically bound in paramagnetic molecules, for which the Breit-Rabi diagram also applies. (orig.)

SYN-RIFT SANDSTONЕS: THE FEATURES OF BULK CHEMICAL COMPOSITIONS, AND POSITIONS ON PALEOGEODYNAMIC DISCRIMINANT DIAGRAMS

Directory of Open Access Journals (Sweden)

A. V. Maslov

2018-01-01

Full Text Available From the early 1980s, the data on the bulk chemical composition of sandstones and mudstones are actively involved for interpretation of the paleogeodynamic settings for sedimentary sequences. Discriminant diagrams such as K2O/Na2O–SiO2/Al2O3 [Maynard et al., 1982], (Fe2O3*+MgO–K2O/Na2O and others [Bhatia, 1983], SiO2–K2O/Na2O [Roser, Korsch, 1986], (K2O+Na2O–SiO2/20–(TiO2+Fe2O3+MgO [Kroonenberg, 1994] etc., are now widely used in regional investigations to classify terrigenous rocks from several paleogeodynamic settings (passive and active continental margins, oceanic and continental volcanic arcs etc. with a certain ‘percentage of consistency’. The first diagrams DF1–DF2 for syn-rift compositions were published in the early 2010s [Verma, Armstrong-Altrin, 2013]. This article analyzes the bulk chemical compositions of syn-rift sandstones from intracratonic rifts and rifts formed during the break-up of the Columbia and Gondwana supercontinents, rifts within volcanic arcs and related to the collapse of collision orogens (for example, Permian sandstones of the Malužiná formation, Western Carpathians, Slovakia. Our database includes the Neoproterozoic Uinta Mountain Group (USA, the Cretaceous Omdurman formation of the Khartoum Basin (Sudan, the siliciclastic deposits of the Kalahari Basin (East African rift zone, the sandstones of the Vindhyan Supergroup (India, the Neoproterozoic Ui Group of the Uchur-Maya region (Southeast Siberia, the Meso-Neoproterozoic Banxi Group (Southern China, the Mesoproterozoic Belt-Purcell Supergroup (USA, the Oronto and Bayfield Groups of the Midcontinent (USA, as well as the sandstones of the Upper Precambrian Ai and Mashak formations, and the metasedimentary rocks of the Arsha Group (Southern Urals. The article examines: (1 the position of the syn-rift sandstone compositions (fields on the log(SiO2/Al2O3–log(Na2O/K2O classification diagram and the F1–F2 diagram, which gives the possible

How design guides learning from matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; Amelsvoort, Marije; Anjewierden, Anjo

2017-01-01

Compared to text, diagrams are superior in their ability to structure and summarize information and to show relations between concepts and ideas. Perceptual cues, like arrows, are expected to improve the retention of diagrams by guiding the learner towards important elements or showing a preferred

Diagram of state of stiff amphiphilic macromolecules

NARCIS (Netherlands)

Markov, Vladimir A.; Vasilevskaya, Valentina V.; Khalatur, Pavel G.; ten Brinke, Gerrit; Khokhlov, Alexei R.

2007-01-01

We studied coil-globule transitions in stiff-chain amphiphilic macromolecules via computer modeling and constructed phase diagrams for such molecules in terms of solvent quality and persistence length. We showed that the shape of the phase diagram essentially depends on the macromolecule degree of

Atomic energy levels and Grotrian diagrams

CERN Document Server

Bashkin, Stanley

1975-01-01

Atomic Energy Levels and Grotrian Diagrams, Volume I: Hydrogen I - Phosphorus XV presents diagrams of various elements that show their energy level and electronic transitions. The book covers the first 15 elements according to their atomic number. The text will be of great use to researchers and practitioners of fields such as astrophysics that requires pictorial representation of the energy levels and electronic transitions of elements.

Updating the Nomographical Diagrams for Dimensioning the Beams

OpenAIRE

Pop Maria T.

2015-01-01

In order to reduce the time period needed for structures design it is strongly recommended to use nomographical diagrams. The base for formation and updating the nomographical diagrams, stands on the charts presented by different technical publications. The updated charts use the same algorithm and calculation elements as the former diagrams in accordance to the latest prescriptions and European standards. The result consists in a chart, having the same properties, similar with the nomogragra...

Spin wave Feynman diagram vertex computation package

Science.gov (United States)

Price, Alexander; Javernick, Philip; Datta, Trinanjan

Spin wave theory is a well-established theoretical technique that can correctly predict the physical behavior of ordered magnetic states. However, computing the effects of an interacting spin wave theory incorporating magnons involve a laborious by hand derivation of Feynman diagram vertices. The process is tedious and time consuming. Hence, to improve productivity and have another means to check the analytical calculations, we have devised a Feynman Diagram Vertex Computation package. In this talk, we will describe our research group's effort to implement a Mathematica based symbolic Feynman diagram vertex computation package that computes spin wave vertices. Utilizing the non-commutative algebra package NCAlgebra as an add-on to Mathematica, symbolic expressions for the Feynman diagram vertices of a Heisenberg quantum antiferromagnet are obtained. Our existing code reproduces the well-known expressions of a nearest neighbor square lattice Heisenberg model. We also discuss the case of a triangular lattice Heisenberg model where non collinear terms contribute to the vertex interactions.

The classification of diagrams in perturbation theory

International Nuclear Information System (INIS)

Phillips, D.R.; Afnan, I.R.

1995-01-01

The derivation of scattering equations connecting the amplitudes obtained from diagrammatic expansions is of interest in many branches of physics. One method for deriving such equations is the classification-of-diagrams technique of Taylor. However, as we shall explain in this paper, there are certain points of Taylor's method which require clarification. First, it is not clear whether Taylor's original method is equivlant to the simpler classification-of-diagrams scheme used by Thomas, Rinat, Afnan, and Blankleider (TRAB). Second, when the Taylor method is applied to certain problems in a time-dependent perturbation theory it leads to the over-counting of some diagrams. This paper first restates Taylor's method, in the process uncovering reasons why certain diagrams might be double-counted in the Taylor method. In then explores how far Taylor's method is equivalent to the simpler TRAB method. Finally, it examines precisely why the double-counting occurs in Taylor's method and derives corrections which compensate for this double-counting. copyright 1995 Academic Press, Inc

Disconnected Diagrams in Lattice QCD

Science.gov (United States)

Gambhir, Arjun Singh

In this work, we present state-of-the-art numerical methods and their applications for computing a particular class of observables using lattice quantum chromodynamics (Lattice QCD), a discretized version of the fundamental theory of quarks and gluons. These observables require calculating so called "disconnected diagrams" and are important for understanding many aspects of hadron structure, such as the strange content of the proton. We begin by introducing the reader to the key concepts of Lattice QCD and rigorously define the meaning of disconnected diagrams through an example of the Wick contractions of the nucleon. Subsequently, the calculation of observables requiring disconnected diagrams is posed as the computationally challenging problem of finding the trace of the inverse of an incredibly large, sparse matrix. This is followed by a brief primer of numerical sparse matrix techniques that overviews broadly used methods in Lattice QCD and builds the background for the novel algorithm presented in this work. We then introduce singular value deflation as a method to improve convergence of trace estimation and analyze its effects on matrices from a variety of fields, including chemical transport modeling, magnetohydrodynamics, and QCD. Finally, we apply this method to compute observables such as the strange axial charge of the proton and strange sigma terms in light nuclei. The work in this thesis is innovative for four reasons. First, we analyze the effects of deflation with a model that makes qualitative predictions about its effectiveness, taking only the singular value spectrum as input, and compare deflated variance with different types of trace estimator noise. Second, the synergy between probing methods and deflation is investigated both experimentally and theoretically. Third, we use the synergistic combination of deflation and a graph coloring algorithm known as hierarchical probing to conduct a lattice calculation of light disconnected matrix elements

Disconnected Diagrams in Lattice QCD

Energy Technology Data Exchange (ETDEWEB)

Gambhir, Arjun [College of William and Mary, Williamsburg, VA (United States)

2017-08-01

In this work, we present state-of-the-art numerical methods and their applications for computing a particular class of observables using lattice quantum chromodynamics (Lattice QCD), a discretized version of the fundamental theory of quarks and gluons. These observables require calculating so called \\disconnected diagrams" and are important for understanding many aspects of hadron structure, such as the strange content of the proton. We begin by introducing the reader to the key concepts of Lattice QCD and rigorously define the meaning of disconnected diagrams through an example of the Wick contractions of the nucleon. Subsequently, the calculation of observables requiring disconnected diagrams is posed as the computationally challenging problem of finding the trace of the inverse of an incredibly large, sparse matrix. This is followed by a brief primer of numerical sparse matrix techniques that overviews broadly used methods in Lattice QCD and builds the background for the novel algorithm presented in this work. We then introduce singular value deflation as a method to improve convergence of trace estimation and analyze its effects on matrices from a variety of fields, including chemical transport modeling, magnetohydrodynamics, and QCD. Finally, we apply this method to compute observables such as the strange axial charge of the proton and strange sigma terms in light nuclei. The work in this thesis is innovative for four reasons. First, we analyze the effects of deflation with a model that makes qualitative predictions about its effectiveness, taking only the singular value spectrum as input, and compare deflated variance with different types of trace estimator noise. Second, the synergy between probing methods and deflation is investigated both experimentally and theoretically. Third, we use the synergistic combination of deflation and a graph coloring algorithm known as hierarchical probing to conduct a lattice calculation of light disconnected matrix elements

PHASE DIAGRAM OF GELATINE-POLYURONATE COLLOIDS: ITS APPLICATION FOR MICROENCAPSULATION AND NOT ONLY

Directory of Open Access Journals (Sweden)

Alexei Baerle

2016-06-01

Full Text Available Phase state and the charge of colloidal particles in the gelatine-polyuronate system were studied. A method for comparative evaluation of molecular weight of colloids by means of viscosimetric measurements and electrophoresis was developed. It is shown that the Diagram {Phase state = f (composition, pH} contains six well-defined regions. The diagram explains and predicts the behaviour of protein-polysaccharide colloids, which are included in beverages or forms the shells of oil-containing microcapsules.

Lattice and Phase Diagram in QCD

International Nuclear Information System (INIS)

Lombardo, Maria Paola

2008-01-01

Model calculations have produced a number of very interesting expectations for the QCD Phase Diagram, and the task of a lattice calculations is to put these studies on a quantitative grounds. I will give an overview of the current status of the lattice analysis of the QCD phase diagram, from the quantitative results of mature calculations at zero and small baryochemical potential, to the exploratory studies of the colder, denser phase.

Ferroelectric Phase Diagram of PVDF:PMMA

OpenAIRE

Li, Mengyuan; Stingelin, Natalie; Michels, Jasper J.; Spijkman, Mark-Jan; Asadi, Kamal; Feldman, Kirill; Blom, Paul W. M.; de Leeuw, Dago M.

2012-01-01

We have investigated the ferroelectric phase diagram of poly(vinylidene fluoride) (PVDF) and poly(methyl methacrylate) (PMMA). The binary nonequilibrium temperature composition diagram was determined and melting of alpha- and beta-phase PVDF was identified. Ferroelectric beta-PVDF:PMMA blend films were made by melting, ice quenching, and subsequent annealing above the glass transition temperature of PMMA, close to the melting temperature of PVDF. Addition of PMMA suppresses the crystallizatio...

Gluing Ladder Feynman Diagrams into Fishnets

International Nuclear Information System (INIS)

Basso, Benjamin; Dixon, Lance J.; Stanford University, CA; University of California, Santa Barbara, CA

2017-01-01

We use integrability at weak coupling to compute fishnet diagrams for four-point correlation functions in planar Φ "4 theory. Our results are always multilinear combinations of ladder integrals, which are in turn built out of classical polylogarithms. The Steinmann relations provide a powerful constraint on such linear combinations, which leads to a natural conjecture for any fishnet diagram as the determinant of a matrix of ladder integrals.

Quantum corrections for the phase diagram of systems with competing order

Science.gov (United States)

Silva, N. L., Jr.; Continentino, Mucio A.; Barci, Daniel G.

2018-06-01

We use the effective potential method of quantum field theory to obtain the quantum corrections to the zero temperature phase diagram of systems with competing order parameters. We are particularly interested in two different scenarios: regions of the phase diagram where there is a bicritical point, at which both phases vanish continuously, and the case where both phases coexist homogeneously. We consider different types of couplings between the order parameters, including a bilinear one. This kind of coupling breaks time-reversal symmetry and it is only allowed if both order parameters transform according to the same irreducible representation. This occurs in many physical systems of actual interest like competing spin density waves, different types of orbital antiferromagnetism, elastic instabilities of crystal lattices, vortices in a multigap SC and also applies to describe the unusual magnetism of the heavy fermion compound URu2Si2. Our results show that quantum corrections have an important effect on the phase diagram of systems with competing orders.

Quantum corrections for the phase diagram of systems with competing order.

Science.gov (United States)

Silva, N L; Continentino, Mucio A; Barci, Daniel G

2018-06-06

We use the effective potential method of quantum field theory to obtain the quantum corrections to the zero temperature phase diagram of systems with competing order parameters. We are particularly interested in two different scenarios: regions of the phase diagram where there is a bicritical point, at which both phases vanish continuously, and the case where both phases coexist homogeneously. We consider different types of couplings between the order parameters, including a bilinear one. This kind of coupling breaks time-reversal symmetry and it is only allowed if both order parameters transform according to the same irreducible representation. This occurs in many physical systems of actual interest like competing spin density waves, different types of orbital antiferromagnetism, elastic instabilities of crystal lattices, vortices in a multigap SC and also applies to describe the unusual magnetism of the heavy fermion compound URu 2 Si 2 . Our results show that quantum corrections have an important effect on the phase diagram of systems with competing orders.

Magnetic phase diagram of HoxTm1-x alloys

DEFF Research Database (Denmark)

Sarthour, R.S.; Cowley, R.A.; Ward, R.C.C.

2000-01-01

The magnetic phase diagram of the competing anisotropy system, Ho/Tm, has been determined by neutron-scattering techniques and the results compared with calculations based on a mean-field model. The crystal-field interactions in Ho favor alignment of the magnetic moments in the basal plane whereas......, with long-range order, were identified and the magnetic phase diagram, including a pentacritical point, determined. A mean-field model was used to explain the results and the results are in good agreement with the experimental results....... in Tm they favor alignment along the c axis. Single-crystal alloys were grown with molecular-beam epitaxy techniques in Oxford. The components of the magnetic moment alone the c direction and in the basal plane were determined from the neutron-scattering measurements. Five distinct magnetic phases...

Pitfalls and feedback when constructing topological pressure-temperature phase diagrams

Science.gov (United States)

Ceolin, R.; Toscani, S.; Rietveld, Ivo B.; Barrio, M.; Tamarit, J. Ll.

2017-04-01

The stability hierarchy between different phases of a chemical compound can be accurately reproduced in a topological phase diagram. This type of phase diagrams may appear to be the result of simple extrapolations, however, experimental complications quickly increase in the case of crystalline trimorphism (and higher order polymorphism). To ensure the accurate positioning of stable phase domains, a topological phase diagram needs to be consistent. This paper gives an example of how thermodynamic feedback can be used in the topological construction of phase diagrams to ensure overall consistency in a phase diagram based on the case of piracetam crystalline trimorphism.

Multicritical phase diagrams of the antiferromagnetic spin-3/2 Blume-Capel model

Energy Technology Data Exchange (ETDEWEB)

Keskin, Mustafa [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)]. E-mail: keskin@erciyes.edu.tr; Ali Pinar, M. [Institute of Science, Erciyes University, 38039 Kayseri (Turkey); Erdinc, Ahmet [Department of Physics, Erciyes University, 38039 Kayseri (Turkey); Canko, Osman [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)

2006-04-24

The antiferromagnetic spin-3/2 Blume-Capel model in an external magnetic field is investigated, and the phase diagrams are obtained in detail by using the cluster variation method. The model exhibits distinct critical regions, including the first-order, second-order and special points: two double critical points, a critical end point, a tricritical point and a zero-temperature critical point. The new phase diagram topology is also found that was not obtained previously. Comparison of the results with those of other studies on this, and closely related systems, is made.

Multicritical phase diagrams of the antiferromagnetic spin-3/2 Blume-Capel model

International Nuclear Information System (INIS)

Keskin, Mustafa; Ali Pinar, M.; Erdinc, Ahmet; Canko, Osman

2006-01-01

The antiferromagnetic spin-3/2 Blume-Capel model in an external magnetic field is investigated, and the phase diagrams are obtained in detail by using the cluster variation method. The model exhibits distinct critical regions, including the first-order, second-order and special points: two double critical points, a critical end point, a tricritical point and a zero-temperature critical point. The new phase diagram topology is also found that was not obtained previously. Comparison of the results with those of other studies on this, and closely related systems, is made

Phase diagram of spiking neural networks.

Science.gov (United States)

Seyed-Allaei, Hamed

2015-01-01

In computer simulations of spiking neural networks, often it is assumed that every two neurons of the network are connected by a probability of 2%, 20% of neurons are inhibitory and 80% are excitatory. These common values are based on experiments, observations, and trials and errors, but here, I take a different perspective, inspired by evolution, I systematically simulate many networks, each with a different set of parameters, and then I try to figure out what makes the common values desirable. I stimulate networks with pulses and then measure their: dynamic range, dominant frequency of population activities, total duration of activities, maximum rate of population and the occurrence time of maximum rate. The results are organized in phase diagram. This phase diagram gives an insight into the space of parameters - excitatory to inhibitory ratio, sparseness of connections and synaptic weights. This phase diagram can be used to decide the parameters of a model. The phase diagrams show that networks which are configured according to the common values, have a good dynamic range in response to an impulse and their dynamic range is robust in respect to synaptic weights, and for some synaptic weights they oscillates in α or β frequencies, independent of external stimuli.

Repair of Partly Misspecified Causal Diagrams.

Science.gov (United States)

Oates, Chris J; Kasza, Jessica; Simpson, Julie A; Forbes, Andrew B

2017-07-01

Errors in causal diagrams elicited from experts can lead to the omission of important confounding variables from adjustment sets and render causal inferences invalid. In this report, a novel method is presented that repairs a misspecified causal diagram through the addition of edges. These edges are determined using a data-driven approach designed to provide improved statistical efficiency relative to de novo structure learning methods. Our main assumption is that the expert is "directionally informed," meaning that "false" edges provided by the expert would not create cycles if added to the "true" causal diagram. The overall procedure is cast as a preprocessing technique that is agnostic to subsequent causal inferences. Results based on simulated data and data derived from an observational cohort illustrate the potential for data-assisted elicitation in epidemiologic applications. See video abstract at, http://links.lww.com/EDE/B208.

Simple method for evaluating Goldstone diagrams in an angular momentum coupled representation

International Nuclear Information System (INIS)

Kuo, T.T.S.; Shurpin, J.; Tam, K.C.; Osnes, E.; Ellis, P.J.

1981-01-01

A simple and convenient method is derived for evaluating linked Goldstone diagrams in an angular momentum coupled representation. Our method is general, and can be used to evaluate any effective interaction and/or effective operator diagrams for both closed-shell nuclei (vacuum to vacuum linked diagrams) and open-shell nuclei (valence linked diagrams). The techniques of decomposing diagrams into ladder diagrams, cutting open internal lines and cutting off one-body insertions are introduced. These enable us to determine angular momentum factors associated with diagrams in the coupled representation directly, without the need for carrying out complicated angular momentum algebra. A summary of diagram rules is given

Diagrams for symmetric product orbifolds

International Nuclear Information System (INIS)

Pakman, Ari; Rastelli, Leonardo; Razamat, Shlomo S.

2009-01-01

We develop a diagrammatic language for symmetric product orbifolds of two-dimensional conformal field theories. Correlation functions of twist operators are written as sums of diagrams: each diagram corresponds to a branched covering map from a surface where the fields are single-valued to the base sphere where twist operators are inserted. This diagrammatic language facilitates the study of the large N limit and makes more transparent the analogy between symmetric product orbifolds and free non-abelian gauge theories. We give a general algorithm to calculate the leading large N contribution to four-point correlators of twist fields.

How Design Guides Learning from Matrix Diagrams

Science.gov (United States)

van der Meij, Jan; van Amelsvoort, Marije; Anjewierden, Anjo

2017-01-01

Compared to text, diagrams are superior in their ability to structure and summarize information and to show relations between concepts and ideas. Perceptual cues, like arrows, are expected to improve the retention of diagrams by guiding the learner towards important elements or showing a preferred reading sequence. In our experiment, we analyzed…

Radiant zone heated particulate filter

Science.gov (United States)

Gonze, Eugene V [Pinckney, MI

2011-12-27

A system includes a particulate matter (PM) filter including an upstream end for receiving exhaust gas and a downstream end. A radiant zoned heater includes N zones, where N is an integer greater than one, wherein each of the N zones includes M sub-zones, where M is an integer greater than or equal to one. A control module selectively activates at least a selected one of the N zones to initiate regeneration in downstream portions of the PM filter from the one of the N zones, restricts exhaust gas flow in a portion of the PM filter that corresponds to the selected one of the N zones, and deactivates non-selected ones of the N zones.

TIME-TEMPERATURE-TRANSFORMATION (TTT) DIAGRAMS FOR FUTURE WASTE COMPOSITIONS

International Nuclear Information System (INIS)

Billings, A.; Edwards, T.

2010-01-01

, subsamples of each glass were isothermally heat treated for 1 to 768 hours at temperatures between 500 C to 1000 C. Each of the heat treated samples, along with quenched and centerline canister cooled (CCC) treated samples, were analyzed using X-ray diffraction (XRD) and the PCT. Maximum crystallization was detected in samples treated at 700 C and 600 C for more than 96 hours in both glasses. Phases crystallized were similar in composition if not the same as those found in the previous TTT studies. Six different crystalline phases were detected, including nepheline, aegirine, lithium silicate, trevorite (spinel based), krinovite, and calcium magnesium iron silicon oxide. Overall, phases were spinel (iron) based, lithium metasilicate, sodium aluminosilicate or alkali transition metal silicate in composition. No new crystalline families were detected. Durability, as measured by the PCT, decreased when lithium silicate or nepheline crystals were present. The conclusions of this study were consistent with previous studies. In order to continue to meet the requirements of the WCP, a simplified strategy is suggested for the generation of future TTT diagrams. Only extremely significant changes in composition resulting from processing strategy changes would require generating more TTT diagrams.

Peircean diagrams of time

DEFF Research Database (Denmark)

Øhrstrøm, Peter

2011-01-01

Some very good arguments can be given in favor of the Augustinean wisdom, according to which it is impossible to provide a satisfactory definition of the concept of time. However, even in the absence of a proper definition, it is possible to deal with conceptual problems regarding time. It can...... be done in terms of analogies and metaphors. In particular, it is attractive to make use of Peirce's diagrams by means of which various kinds of conceptual experimentation can be carried out. This paper investigates how Peircean diagrams can be used within the study of time. In particular, we discuss 1......) the topological properties of time, 2) the implicative structure in tense logic, 3) the notions of open future and branching time models, and finally 4) tenselogical alternatives to branching time models....

Extended sequence diagram for human system interaction

International Nuclear Information System (INIS)

Hwang, Jong Rok; Choi, Sun Woo; Ko, Hee Ran; Kim, Jong Hyun

2012-01-01

Unified Modeling Language (UML) is a modeling language in the field of object oriented software engineering. The sequence diagram is a kind of interaction diagram that shows how processes operate with one another and in what order. It is a construct of a message sequence chart. It depicts the objects and classes involved in the scenario and the sequence of messages exchanged between the objects needed to carry out the functionality of the scenario. This paper proposes the Extended Sequence Diagram (ESD), which is capable of depicting human system interaction for nuclear power plants, as well as cognitive process of operators analysis. In the conventional sequence diagram, there is a limit to only identify the activities of human and systems interactions. The ESD is extended to describe operators' cognitive process in more detail. The ESD is expected to be used as a task analysis method for describing human system interaction. The ESD can also present key steps causing abnormal operations or failures and diverse human errors based on cognitive condition

An Introduction to Binary Decision Diagrams

DEFF Research Database (Denmark)

Andersen, Henrik Reif

1996-01-01

This note is a short introduction to Binary Decision Diagrams (BDDs). It provides some background knowledge and describes the core algorithms. It is used in the course "C4340 Advanced Algorithms" at the Technical University of Denmark, autumn 1996.......This note is a short introduction to Binary Decision Diagrams (BDDs). It provides some background knowledge and describes the core algorithms. It is used in the course "C4340 Advanced Algorithms" at the Technical University of Denmark, autumn 1996....

(α,η) phase diagrams in tilted chiral smectics

International Nuclear Information System (INIS)

Rjili, M.; Marcerou, J.P.; Gharbi, A.; Othman, T.

2013-01-01

The polymorphism of tilted chiral smectics liquid crystals is incredibly rich and encompasses many subphases such as SmC A ⁎ ; SmC Fi1 ⁎ ; SmC Fi2 ⁎ ; SmC ⁎ ; SmC α ⁎ . The continuum theory established by Marcerou (2010) is used to derive an expression for the free energy density of those subphases. The minimization of this free energy is obtained through a combination of analytical and numerical methods. It leads to a phase diagram built in the (α,η) plane where α is local angular parameter and η describes the variation of the temperature. From this graphical representation, many experimentally observed phase sequences of ferroelectric liquid crystals can be explained, even them including subphases which were recently observed like the SmC 5 ⁎ and the SmC 6 ⁎ ones. However, it should be emphasized that the details of predicted phase diagram are strongly dependent on the compound studied.

Construction of UML class diagram with Model-Driven Development

Directory of Open Access Journals (Sweden)

Tomasz Górski

2016-03-01

Full Text Available Model transformations play a key role in software development projects based on Model--Driven Development (MDD principles. Transformations allow for automation of repetitive and well-defined steps, thus shortening design time and reducing a number of errors. In the object-oriented approach, the key elements are use cases. They are described, modelled and later designed until executable application code is obtained. The aim of the paper is to present transformation of a model-to-model type, Communication-2-Class, which automates construction of Unified Modelling Language (UML class diagram in the context of the analysis/design model. An UML class diagram is created based on UML communication diagram within use case realization. As a result, a class diagram shows all of the classes involved in the use case realization and the relationships among them. The plug-in which implements Communication-2-Class transformation was implemented in the IBM Rational Software Architect. The article presents the tests results of developed plug-in, which realizes Communication-2-Class transformation, showing capabilities of shortening use case realization’s design time.[b]Keywords[/b]: Model-Driven Development, transformations, Unified Modelling Language, analysis/design model, UML class diagram, UML communication diagram

Efficient computation of clipped Voronoi diagram for mesh generation

KAUST Repository

Yan, Dongming

2013-04-01

The Voronoi diagram is a fundamental geometric structure widely used in various fields, especially in computer graphics and geometry computing. For a set of points in a compact domain (i.e. a bounded and closed 2D region or a 3D volume), some Voronoi cells of their Voronoi diagram are infinite or partially outside of the domain, but in practice only the parts of the cells inside the domain are needed, as when computing the centroidal Voronoi tessellation. Such a Voronoi diagram confined to a compact domain is called a clipped Voronoi diagram. We present an efficient algorithm to compute the clipped Voronoi diagram for a set of sites with respect to a compact 2D region or a 3D volume. We also apply the proposed method to optimal mesh generation based on the centroidal Voronoi tessellation. Crown Copyright © 2011 Published by Elsevier Ltd. All rights reserved.

Efficient computation of clipped Voronoi diagram for mesh generation

KAUST Repository

Yan, Dongming; Wang, Wen Ping; Lé vy, Bruno L.; Liu, Yang

2013-01-01

The Voronoi diagram is a fundamental geometric structure widely used in various fields, especially in computer graphics and geometry computing. For a set of points in a compact domain (i.e. a bounded and closed 2D region or a 3D volume), some Voronoi cells of their Voronoi diagram are infinite or partially outside of the domain, but in practice only the parts of the cells inside the domain are needed, as when computing the centroidal Voronoi tessellation. Such a Voronoi diagram confined to a compact domain is called a clipped Voronoi diagram. We present an efficient algorithm to compute the clipped Voronoi diagram for a set of sites with respect to a compact 2D region or a 3D volume. We also apply the proposed method to optimal mesh generation based on the centroidal Voronoi tessellation. Crown Copyright © 2011 Published by Elsevier Ltd. All rights reserved.

A Community Based Systems Diagram of Obesity Causes.

Directory of Open Access Journals (Sweden)

Steven Allender

Full Text Available Application of system thinking to the development, implementation and evaluation of childhood obesity prevention efforts represents the cutting edge of community-based prevention. We report on an approach to developing a system oriented community perspective on the causes of obesity.Group model building sessions were conducted in a rural Australian community to address increasing childhood obesity. Stakeholders (n = 12 built a community model that progressed from connection circles to causal loop diagrams using scripts from the system dynamics literature. Participants began this work in identifying change over time in causes and effects of childhood obesity within their community. The initial causal loop diagram was then reviewed and elaborated by 50 community leaders over a full day session.The process created a causal loop diagram representing community perceptions of determinants and causes of obesity. The causal loop diagram can be broken down into four separate domains; social influences; fast food and junk food; participation in sport; and general physical activity.This causal loop diagram can provide the basis for community led planning of a prevention response that engages with multiple levels of existing settings and systems.

An approach for continuous cooling transformation (CCT) diagrams of aluminium alloys

International Nuclear Information System (INIS)

Herding, T.; Kessler, O.; Hoffmann, F.; Mayr, P.

2002-01-01

Two different kinds of time temperature transformation (TTT) diagrams are known. The first one are isothermal transformation (IT) diagrams and the second one continuous cooling transformation (CCT) diagrams. These diagrams are important for the correct heat treatment of aluminium alloys, because they provide information about the required quenching rate, which is necessary to obtain a supersaturated solid solution during age hardening. Furthermore, it is possible to determine the lowest quenching rate, which permits both a high strength and a small distortion of the component after age hardening. In the literature IT diagrams for different aluminium alloys are available. To determine these diagrams, a solution annealing followed by quenching to defined temperatures is necessary. At these temperatures the alloy is kept isothermally until a transformation has started. These diagrams are not directly portable on continuous cooling, because of the different cooling paths. (orig.)

Effects of Three Diagram Instruction Methods on Transfer of Diagram Comprehension Skills: The Critical Role of Inference While Learning

Science.gov (United States)

Cromley, Jennifer G.; Bergey, Bradley W.; Fitzhugh, Shannon; Newcombe, Nora; Wills, Theodore W.; Shipley, Thomas F.; Tanaka, Jacqueline C.

2013-01-01

Can students be taught to better comprehend the diagrams in their textbooks? Can such teaching transfer to uninstructed diagrams in the same domain or even in a new domain? What methods work best for these goals? Building on previous research showing positive results compared to control groups in both laboratory studies and short-term…

eulerAPE: drawing area-proportional 3-Venn diagrams using ellipses.

Science.gov (United States)

Micallef, Luana; Rodgers, Peter

2014-01-01

Venn diagrams with three curves are used extensively in various medical and scientific disciplines to visualize relationships between data sets and facilitate data analysis. The area of the regions formed by the overlapping curves is often directly proportional to the cardinality of the depicted set relation or any other related quantitative data. Drawing these diagrams manually is difficult and current automatic drawing methods do not always produce appropriate diagrams. Most methods depict the data sets as circles, as they perceptually pop out as complete distinct objects due to their smoothness and regularity. However, circles cannot draw accurate diagrams for most 3-set data and so the generated diagrams often have misleading region areas. Other methods use polygons to draw accurate diagrams. However, polygons are non-smooth and non-symmetric, so the curves are not easily distinguishable and the diagrams are difficult to comprehend. Ellipses are more flexible than circles and are similarly smooth, but none of the current automatic drawing methods use ellipses. We present eulerAPE as the first method and software that uses ellipses for automatically drawing accurate area-proportional Venn diagrams for 3-set data. We describe the drawing method adopted by eulerAPE and we discuss our evaluation of the effectiveness of eulerAPE and ellipses for drawing random 3-set data. We compare eulerAPE and various other methods that are currently available and we discuss differences between their generated diagrams in terms of accuracy and ease of understanding for real world data.

eulerAPE: drawing area-proportional 3-Venn diagrams using ellipses.

Directory of Open Access Journals (Sweden)

Luana Micallef

Full Text Available Venn diagrams with three curves are used extensively in various medical and scientific disciplines to visualize relationships between data sets and facilitate data analysis. The area of the regions formed by the overlapping curves is often directly proportional to the cardinality of the depicted set relation or any other related quantitative data. Drawing these diagrams manually is difficult and current automatic drawing methods do not always produce appropriate diagrams. Most methods depict the data sets as circles, as they perceptually pop out as complete distinct objects due to their smoothness and regularity. However, circles cannot draw accurate diagrams for most 3-set data and so the generated diagrams often have misleading region areas. Other methods use polygons to draw accurate diagrams. However, polygons are non-smooth and non-symmetric, so the curves are not easily distinguishable and the diagrams are difficult to comprehend. Ellipses are more flexible than circles and are similarly smooth, but none of the current automatic drawing methods use ellipses. We present eulerAPE as the first method and software that uses ellipses for automatically drawing accurate area-proportional Venn diagrams for 3-set data. We describe the drawing method adopted by eulerAPE and we discuss our evaluation of the effectiveness of eulerAPE and ellipses for drawing random 3-set data. We compare eulerAPE and various other methods that are currently available and we discuss differences between their generated diagrams in terms of accuracy and ease of understanding for real world data.

XLOOPS - a package calculating one- and two-loop diagrams

International Nuclear Information System (INIS)

Bruecher, L.

1997-01-01

A program package for calculating massive one- and two-loop diagrams is introduced. It consists of five parts: - a graphical user interface, - routines for generating diagrams from particle input, - procedures for calculating one-loop integrals both analytically and numerically, - routines for massive two-loop integrals, - programs for numerical integration of two-loop diagrams. Here the graphical user interface and the text interface to Maple are presented. (orig.)

Oak Ridge K-25 Site Technology Logic Diagram. Volume 2, Technology Logic Diagrams

Energy Technology Data Exchange (ETDEWEB)

Fellows, R.L. [ed.

1993-02-26

The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates envirorunental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. This volume, Volume 2, contains logic diagrams with an index. Volume 3 has been divided into two separate volumes to facilitate handling and use.

Grotrian diagrams of highly ionized iron Fe(VIII)-Fe(XXVI)

International Nuclear Information System (INIS)

Mori, Kazuo; Otsuka, Masamoto; Kato, Takako.

1977-08-01

Energy levels and Grotrian diagrams of Fe(VIII) to Fe(XXVI) are presented. This report summarized the data published recently up to 1976, and the wavelength tables compiled were converted to the Grotrian diagrams. The diagrams showing transition from one energy level to another are called Grotrian diagrams. Typical examples of the diagrams are found in the book by Bashkin et al. In the present diagrams, all lines are drawn in parallel, and connected to the extended lines from lower levels. As the results, locally dense packing of lines and figures is avoided. The ordinate of the diagrams indicates level energy, and the J values are shown on the left side of the levels. The wavelength values in angstrom unit are written in parallel with the vertical transition lines. This vertical lines show the resonance transition having absorption oscillator strength f larger than 0.1. The present diagrams are the combination of the tables of wavelength and energy level. Accordingly, the desired wavelength and level energy are easily found. The figures of wavelength are lined up in various groups, so that the characteristics of the transition can be discriminated at a glance. Wavelength and level energy have been mostly derived from experimental spectra in laboratory or solar plasma, except a few by Fawcett's prediction. (Kato, T.)

Triangular Diagrams Teach Steady and Dynamic Behaviour of Catalytic Reactions.

Science.gov (United States)

Klusacek, K.; And Others

1989-01-01

Illustrates how triangular diagrams can aid in presenting some of the rather complex transient interactions that occur among gas and surface species during heterogeneous catalytic reactions. The basic equations and numerical examples are described. Classroom use of the triangular diagram is discussed. Several diagrams and graphs are provided. (YP)

Analysis of Sequence Diagram Layout in Advanced UML Modelling Tools

Directory of Open Access Journals (Sweden)

Ņikiforova Oksana

2016-05-01

Full Text Available System modelling using Unified Modelling Language (UML is the task that should be solved for software development. The more complex software becomes the higher requirements are stated to demonstrate the system to be developed, especially in its dynamic aspect, which in UML is offered by a sequence diagram. To solve this task, the main attention is devoted to the graphical presentation of the system, where diagram layout plays the central role in information perception. The UML sequence diagram due to its specific structure is selected for a deeper analysis on the elements’ layout. The authors research represents the abilities of modern UML modelling tools to offer automatic layout of the UML sequence diagram and analyse them according to criteria required for the diagram perception.

Applications of zero-suppressed decision diagrams

CERN Document Server

Sasao, Tsutomu

2014-01-01

A zero-suppressed decision diagram (ZDD) is a data structure to represent objects that typically contain many zeros. Applications include combinatorial problems, such as graphs, circuits, faults, and data mining. This book consists of four chapters on the applications of ZDDs. The first chapter by Alan Mishchenko introduces the ZDD. It compares ZDDs to BDDs, showing why a more compact representation is usually achieved in a ZDD. The focus is on sets of subsets and on sum-of-products (SOP) expressions. Methods to generate all the prime implicants (PIs), and to generate irredundant SOPs are show

Vesicle computers: Approximating a Voronoi diagram using Voronoi automata

International Nuclear Information System (INIS)

Adamatzky, Andrew; De Lacy Costello, Ben; Holley, Julian; Gorecki, Jerzy; Bull, Larry

2011-01-01

Highlights: → We model irregular arrangements of vesicles filled with chemical systems. → We examine influence of precipitation threshold on the system's computational potential. → We demonstrate computation of Voronoi diagram and skeleton. - Abstract: Irregular arrangements of vesicles filled with excitable and precipitating chemical systems are imitated by Voronoi automata - finite-state machines defined on a planar Voronoi diagram. Every Voronoi cell takes four states: resting, excited, refractory and precipitate. A resting cell excites if it has at least one neighbour in an excited state. The cell precipitates if the ratio of excited cells in its neighbourhood versus the number of neighbours exceeds a certain threshold. To approximate a Voronoi diagram on Voronoi automata we project a planar set onto the automaton lattice, thus cells corresponding to data-points are excited. Excitation waves propagate across the Voronoi automaton, interact with each other and form precipitate at the points of interaction. The configuration of the precipitate represents the edges of an approximated Voronoi diagram. We discover the relationship between the quality of the Voronoi diagram approximation and the precipitation threshold, and demonstrate the feasibility of our model in approximating Voronoi diagrams of arbitrary-shaped objects and in constructing a skeleton of a planar shape.

Developing Tool Support for Problem Diagrams with CPN and VDM++

DEFF Research Database (Denmark)

Tjell, Simon; Lassen, Kristian Bisgaard

2008-01-01

In this paper, we describe ongoing work on the development of tool support for formal description of domains found in Problem Diagrams. The purpose of the tool is to handle the generation of a CPN model based on a collection of Problem Diagrams. The Problem Diagrams are used for representing the ...

A Generalized Wave Diagram for Moving Sources

Science.gov (United States)

Alt, Robert; Wiley, Sam

2004-12-01

Many introductory physics texts1-5 accompany the discussion of the Doppler effect and the formation of shock waves with diagrams illustrating the effect of a source moving through an elastic medium. Typically these diagrams consist of a series of equally spaced dots, representing the location of the source at different times. These are surrounded by a series of successively smaller circles representing wave fronts (see Fig. 1). While such a diagram provides a clear illustration of the shock wave produced by a source moving at a speed greater than the wave speed, and also the resultant pattern when the source speed is less than the wave speed (the Doppler effect), the texts do not often show the details of the construction. As a result, the key connection between the relative distance traveled by the source and the distance traveled by the wave is not explicitly made. In this paper we describe an approach emphasizing this connection that we have found to be a useful classroom supplement to the usual text presentation. As shown in Fig. 2 and Fig. 3, the Doppler effect and the shock wave can be illustrated by diagrams generated by the construction that follows.

Testing of multidimensional tectonomagmatic discrimination diagrams on fresh and altered rocks

Directory of Open Access Journals (Sweden)

Rivera-Gómez M. Abdelaly

2016-04-01

Full Text Available We evaluated 55 multidimensional diagrams proposed during 2004-2013 for the tectonic discrimination of ultrabasic, basic, intermediate, and acid magmas. The Miocene to Recent rock samples for testing the diagrams had not been used for constructing them. Eighteen test studies (2 from ocean island; 2 from ocean island/continental rift; 6 from continental rift; 4 from continental arc; 2 from island arc; 1 from mid-ocean ridge, and 1 from collision of relatively fresh rocks fully confirmed the satisfactory functioning of these diagrams for all tectonic fields for which they were proposed. Eight additional case studies on hydrothermally altered or moderately to highly weathered rocks were also presented to achieve further understanding of the functioning of these diagrams. For these rocks as well, the diagrams indicated the expected tectonic setting. We also show that for testing or using these diagrams the freely-available geochemistry databases should be used with caution but certainly after ascertaining the correct magma types to select the appropriate diagram sets. The results encourage us to recommend these diagrams for deciphering the tectonic setting of older terranes or areas with complex or transitional tectonic settings.

Logical and Geometrical Distance in Polyhedral Aristotelian Diagrams in Knowledge Representation

Directory of Open Access Journals (Sweden)

Lorenz Demey

2017-09-01

Full Text Available Aristotelian diagrams visualize the logical relations among a finite set of objects. These diagrams originated in philosophy, but recently, they have also been used extensively in artificial intelligence, in order to study (connections between various knowledge representation formalisms. In this paper, we develop the idea that Aristotelian diagrams can be fruitfully studied as geometrical entities. In particular, we focus on four polyhedral Aristotelian diagrams for the Boolean algebra B 4 , viz. the rhombic dodecahedron, the tetrakis hexahedron, the tetraicosahedron and the nested tetrahedron. After an in-depth investigation of the geometrical properties and interrelationships of these polyhedral diagrams, we analyze the correlation (or lack thereof between logical (Hamming and geometrical (Euclidean distance in each of these diagrams. The outcome of this analysis is that the Aristotelian rhombic dodecahedron and tetrakis hexahedron exhibit the strongest degree of correlation between logical and geometrical distance; the tetraicosahedron performs worse; and the nested tetrahedron has the lowest degree of correlation. Finally, these results are used to shed new light on the relative strengths and weaknesses of these polyhedral Aristotelian diagrams, by appealing to the congruence principle from cognitive research on diagram design.

Mollier-h,x diagram for moist flue gas

Energy Technology Data Exchange (ETDEWEB)

Mueller, H; Hultsch, T; Suder, M

1984-07-01

Diagrams and formulae are presented for calculation of enthalpy and moisture content of flue gas from brown coal, heating oil, black coal and brown coal briquet combustion. The enthalpy (in kJ/kg) and moisture (g/kg) diagrams were established by computer graphics for pressure 0.1 MPa. A further diagram is provided for enthalpy and flue gas moisture, varying the combustion air supply according to coal dust and to grate firing. These thermodynamic calculations are regarded as significant for assessing methods of flue gas cooling below the moisture dew point and for waste heat recovery. 3 references.

Research principles and the construction of mnemonic diagrams

Science.gov (United States)

Venda, V. F.; Mitkin, A. A.

1973-01-01

Mnemonic diagrams are defined as a variety of information display devices, the essential element of which is conventional graphical presentation of technological or functional-operational links in a controlled system or object. Graphically displaying the operational structure of an object, the interd dependence between different parameters, and the interdependence between indicators and control organs, the mneomonic diagram reduces the load on the operator's memory and facilitates perception and reprocessing of information and decision making, while at the same time playing the role of visual support to the information activity of the operator. The types of mnemonic diagrams are listed.

Success and failure with phthalate buffers in capillary zone electrophoresis.

Science.gov (United States)

Bocek, P; Gebauer, P; Beckers, J L

2001-04-01

Phthalate buffers are currently used in capillary electrophoresis as robust electrolyte systems for indirect detection. This contribution demonstrates that these buffers show regularly not only successful regions of mobilities of analytes (sample window) but also regions of failure where the migration of analytes is strongly deteriorated due to the presence of a system zone. System zones in phthalate buffers may be easily detected by UV detection and manifest themselves as peaks or dips. Peak shape diagrams are advantageously used for the prediction of the migration behavior of system zones in phthalate background electrolyte (BGE) systems at various pH. It is shown that the mobility of the system zone varies strongly with pH, is practically zero at pH values below 4 and above 7, and shows a maximum at pH 5. Thus, the system peak may coincide either with the peaks of various analytes or with the electroosmotic flow (EOF) peak. Experiments are given showing the effects of such coincidences as, e.g., zigzag detection patterns, double EOF peaks, and/or unusually broad peaks/dips. The message of this contribution is to show how to understand the electrophoretic properties of phthalate BGEs that, regardless of possible failure regions, may be successfully used in the analytical practice of capillary zone electrophoresis (CZE).

Infrared thermography method for fast estimation of phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Palomo Del Barrio, Elena [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Cadoret, Régis [Centre National de la Recherche Scientifique, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Daranlot, Julien [Solvay, Laboratoire du Futur, 178 Av du Dr Schweitzer, 33608 Pessac (France); Achchaq, Fouzia, E-mail: fouzia.achchaq@u-bordeaux.fr [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France)

2016-02-10

Highlights: • Infrared thermography is proposed to determine phase diagrams in record time. • Phase boundaries are detected by means of emissivity changes during heating. • Transition lines are identified by using Singular Value Decomposition techniques. • Different binary systems have been used for validation purposes. - Abstract: Phase change materials (PCM) are widely used today in thermal energy storage applications. Pure PCMs are rarely used because of non adapted melting points. Instead of them, mixtures are preferred. The search of suitable mixtures, preferably eutectics, is often a tedious and time consuming task which requires the determination of phase diagrams. In order to accelerate this screening step, a new method for estimating phase diagrams in record time (1–3 h) has been established and validated. A sample composed by small droplets of mixtures with different compositions (as many as necessary to have a good coverage of the phase diagram) deposited on a flat substrate is first prepared and cooled down to ambient temperature so that all droplets crystallize. The plate is then heated at constant heating rate up to a sufficiently high temperature for melting all the small crystals. The heating process is imaged by using an infrared camera. An appropriate method based on singular values decomposition technique has been developed to analyze the recorded images and to determine the transition lines of the phase diagram. The method has been applied to determine several simple eutectic phase diagrams and the reached results have been validated by comparison with the phase diagrams obtained by Differential Scanning Calorimeter measurements and by thermodynamic modelling.

Sistem Informasi Penjualan dan Pemesanan Layanan Berbasis Web dan SMS Gateway di Petshop "PetZone"

Directory of Open Access Journals (Sweden)

Siska Fadhilah Wati

2013-09-01

Full Text Available Dewasa ini teknologi informasi sangat membantu dalam dunia bisnis. Kemudahan yang ditawarkan akan menjaring lebih banyak konsumen. Namun, perusahan tingkat menengah seperti PetZone saat ini masih jarang yang menawarkan kemudahan berbelanja atau pemesanan layanan secara online. Oleh karena itu diperlukan sebuah sistem berbasis web di perusahaan PetZone yang dapat memudahkan pemilik dan karyawan dalam apenjualan, pelayanan, dan pemasaran, serta memudahkan pelanggan dalam jual-beli barang dan jasa. Atas dasar masalah tersebut dibangun Sistem Informasi Penjualan dan Pemesanan Layanan Berbasis Web dan SMS Gateway untuk menunjang proses bisnis yang ada. Sistem informasi dibangun menggunakan bahasa pemrograman PHP framework Codeigniter, javascript untuk tampilan yang dinamis, dan database MySQL. Proses pembuatan dan pengembangan Sistem Informasi Penjualan ini menggunakan metode air terjun. Metode air terjun meliputi kebutuhan pengguna, analisis, rancangan, implementasi dan pengujian. Pemodelan Sistem Informasi yang dibangun menggunakan metode berorientasi objek UML (Unified Modeling Language yang terdiri dari Use case  diagram, Class diagram dan Sequence diagram. Hasil pengujian Sistem Informasi Penjualan dan Pemesanan Layanan Berbasis Web dan SMS Gateway menunjukkan bahwa semua fitur yang terdapat baik dalam sistem informasi maupun SMS gateway dapat bekerja dengan baikdengan ratusan sample data, dan server SMS gateway dapat memproses lebih dari satu SMS secara bersamaan. Dalam perkembangan ke depannya nanti, Sistem Informasi Penjualan dan Pemesanan Layanan Berbasis Web dan SMS Gateway masih dapat dikembangkan lagi dengan menambah fitur-fitur pada SMS gateway sehingga lebih memudahkan konsumen.

Improvements in Logic Diagram of Computerized Procedure System of APR1400

Energy Technology Data Exchange (ETDEWEB)

Kang, Sungkweon; Seong, Nokyu [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Computerized Procedure System (CPS) has been improved since it is installed in Shin-Kori 3 and 4 Nuclear Power Plants. It is one of operating support systems of digital Main Control Room (MCR) and provides many functions to operators in executing the procedure. CPS can effectively remove the human errors by supporting the procedure flow and logic diagram. This paper describes the logic diagram of CPS of reference power plant and shows the improved logic diagram of CPS of Shin-Kori unit 5 and 6. This paper describes the current logic diagram of CPS and suggests improved design for logic diagram. The improved logic diagram shall be validated through human factors engineering verification and validation. The improved design will help operators execute the computerized procedure fast and remove the human error.

Use of high-speed cinematography and computer generated gait diagrams for the study of equine hindlimb kinematics.

Science.gov (United States)

Kobluk, C N; Schnurr, D; Horney, F D; Sumner-Smith, G; Willoughby, R A; Dekleer, V; Hearn, T C

1989-01-01

High-speed cinematography with computer aided analysis was used to study equine hindlimb kinematics. Eight horses were filmed at the trot or the pace. Filming was done from the side (lateral) and the back (caudal). Parameters measured from the lateral filming included the heights of the tuber coxae and tailhead, protraction and retraction of the hoof and angular changes of the tarsus and stifle. Abduction and adduction of the limb and tarsal height changes were measured from the caudal filming. The maximum and minimum values plus the standard deviations and coefficients of variations are presented in tabular form. Three gait diagrams were constructed to represent stifle angle versus tarsal angle, metatarsophalangeal height versus protraction-retraction (fetlock height diagram) and tuber coxae and tailhead height versus stride (pelvic height diagram). Application of the technique to the group of horses revealed good repeatability of the gait diagrams within a limb and the diagrams appeared to be sensitive indicators of left/right asymmetries.

Evaluation of Front Morphological Development of Reactive Solute Transport Using Behavior Diagrams

Directory of Open Access Journals (Sweden)

Jui-Sheng Chen

2009-01-01

Full Text Available While flowing through porous medium, ground water flow dissolves minerals thereby in creasing medium porosity and ultimately permeability. Reactive fluid flows preferentially into highly permeable zones, which are therefore dissolved most rapidly, producing a further preferential permeability enhancement. Accordingly, slight non-uniformities present in porous medium can be amplified and lead to fingering reaction fronts. The objective of this study is to investigate dissolution-induced porosity changes on reaction front morphology in homogeneous porous medium with two non-uniformities. Four controlling parameters, including up stream pressure gradient, reaction rate constant, non-uniformities spacing and non-uniformity strength ratio are comprehensively considered. By using a modified version of the numerical code, NSPCRT, to conduct a series of numerical simulations, front behavior diagrams are constructed to illustrate the morphologies of reaction fronts under various combinations of these four factors. Simulation results indicate that the two non-uniformities are inhibited into a planar front under low up stream pressure gradient, merge into a single-fingering front under inter mediate up stream pressure gradient, or grow into a double-fingers front under high up stream pressure gradient. More over, the two non-uniformities tend to develop intoadouble-fingering front as the non-uniformity strength ratio in creases from 0.2 to 1.0, and merge into a single-fingering front while the non-uniformity strength ratio in creases from 1.0 to 1.8. When the reaction rate constant is small, the two non-uniformities merge into a single front. Reaction rate constant significantly affects front advancing velocity. The front advancing velocity decreases with the reaction rate constant. Based on these results, front behavior diagrams which de fine the morphologies of the reaction fronts for these four parameters are constructed. Moreover, non

State diagram of Pr-Bi system

International Nuclear Information System (INIS)

Abulkhaev, V.L.; Ganiev, I.N.

1994-01-01

By means of thermal differential analysis, X-ray and microstructural analysis the state diagram of Pr-Bi system was studied. Following intermetallic compounds were defined in the system: Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 , Pr Bi, PrBi 2 , Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 and PrBi 2 . The data analysis on Ln-Bi diagram allowed to determine the regularity of change of properties of intermetallic compounds in the line of rare earth elements of cerium subgroup.

Fusion Diagrams in the - and - Systems

Science.gov (United States)

Asadov, M. M.; Akhmedova, N. A.

2014-10-01

A calculation model of the Gibbs energy of ternary oxide compounds from the binary components was used. Thermodynamic properties of -- ternary systems in the condensed state were calculated. Thermodynamic data of binary and ternary compounds were used to determine the stable sections. The probability of reactions between the corresponding components in the -- system was estimated. Fusibility diagrams of systems - and - were studied by physical-chemical analysis. The isothermal section of the phase diagram of -- at 298 K is built, as well as the projection of the liquid surface of --.

An Application of Mosaic Diagrams to the Visualization of Set Relationships

OpenAIRE

Luz, Saturnino; Masoodian, Masood

2017-01-01

We present an application of mosaic diagrams to the visualisation of set relations. Venn and Euler diagrams are the best known visual representations of sets and their relationships (intersections, containment or subsets, exclusion or disjointness). In recent years, alternative forms of visualisation have been proposed. Among them, linear diagrams have been shown to compare favourably to Venn and Euler diagrams, in supporting non-interactive assessment of set relationships. Recent studies tha...

Thermodynamic modeling of phase relations and metasomatism in shear zones

Science.gov (United States)

Goncalves, P.; Oliot, E.; Marquer, D.

2009-04-01

Ductile shear zones have been recognized for a long time as privileged sites of intense fluid-rock interactions in the crust. In most cases they induce focused changes in mineralogy and bulk chemical composition (metasomatism) which in turn may control the deformation and fluid-migration processes. Therefore understanding these processes requires in a first step to be able to model phase relations in such open system. In this contribution, emphasizes in placed on metasomatic aspects of the problem. Indeed , in many ductile shear zones reported in metagranites, deformation and fluid-rock interactions are associated with gain in MgO and losses of CaO and Na2O (K2O is also a mobile component but it can be either gained or lost). Although the mineralogical consequences of this so-called Mg-metasomatism are well-documented (replacement of K-feldspar into phengite, breakdown of plagioclase into ab + ep, crystallization of chlorite), the origin of this coupled mass-transfer is still unknown. We have performed a forward modeling of phase relationships using petrogenetic grids and pseudosections that consider variations in chemical potential (μ) of the mobile elements (MgO, CaO, Na2O). Chemical potential gradients being the driving force of mass transfer, μ-μ diagrams are the most appropriate diagrams to model open systems where fluid-rock interactions are prominent. Chemical potential diagrams are equivalent to activity diagrams but our approach differs from previous work because (1) solid solutions are taken into account (2) phase relations are modeled in a more realistic chemical system (Na2O-CaO-K2O-FeO-MgO-Al2O3-SiO2-H2O) and (3) the use of pseudosections allows to predict changes of the mineralogy (modes, composition) for the specific bulk composition studied. A particular attention is paid to the relationships between component concentrations and chemical potentials, which is not obvious in multi-component system. The studied shear zone is located in the Grimsel

Using reweighting and free energy surface interpolation to predict solid-solid phase diagrams

Science.gov (United States)

Schieber, Natalie P.; Dybeck, Eric C.; Shirts, Michael R.

2018-04-01

Many physical properties of small organic molecules are dependent on the current crystal packing, or polymorph, of the material, including bioavailability of pharmaceuticals, optical properties of dyes, and charge transport properties of semiconductors. Predicting the most stable crystalline form at a given temperature and pressure requires determining the crystalline form with the lowest relative Gibbs free energy. Effective computational prediction of the most stable polymorph could save significant time and effort in the design of novel molecular crystalline solids or predict their behavior under new conditions. In this study, we introduce a new approach using multistate reweighting to address the problem of determining solid-solid phase diagrams and apply this approach to the phase diagram of solid benzene. For this approach, we perform sampling at a selection of temperature and pressure states in the region of interest. We use multistate reweighting methods to determine the reduced free energy differences between T and P states within a given polymorph and validate this phase diagram using several measures. The relative stability of the polymorphs at the sampled states can be successively interpolated from these points to create the phase diagram by combining these reduced free energy differences with a reference Gibbs free energy difference between polymorphs. The method also allows for straightforward estimation of uncertainties in the phase boundary. We also find that when properly implemented, multistate reweighting for phase diagram determination scales better with the size of the system than previously estimated.

Plotting and Analyzing Data Trends in Ternary Diagrams Made Easy

Science.gov (United States)

John, Cédric M.

2004-04-01

Ternary plots are used in many fields of science to characterize a system based on three components. Triangular plotting is thus useful to a broad audience in the Earth sciences and beyond. Unfortunately, it is typically the most expensive commercial software packages that offer the option to plot data in ternary diagrams, and they lack features that are paramount to the geosciences, such as the ability to plot data directly into a standardized diagram and the possibility to analyze temporal and stratigraphic trends within this diagram. To address these issues, δPlot was developed with a strong emphasis on ease of use, community orientation, and availability free of charges. This ``freeware'' supports a fully graphical user interface where data can be imported as text files, or by copying and pasting. A plot is automatically generated, and any standard diagram can be selected for plotting in the background using a simple pull-down menu. Standard diagrams are stored in an external database of PDF files that currently holds some 30 diagrams that deal with different fields of the Earth sciences. Using any drawing software supporting PDF, one can easily produce new standard diagrams to be used with δPlot by simply adding them to the library folder. An independent column of values, commonly stratigraphic depths or ages, can be used to sort the data sets.

Phase diagram of an extended Agassi model

Science.gov (United States)

García-Ramos, J. E.; Dukelsky, J.; Pérez-Fernández, P.; Arias, J. M.

2018-05-01

Background: The Agassi model [D. Agassi, Nucl. Phys. A 116, 49 (1968), 10.1016/0375-9474(68)90482-X] is an extension of the Lipkin-Meshkov-Glick (LMG) model [H. J. Lipkin, N. Meshkov, and A. J. Glick, Nucl. Phys. 62, 188 (1965), 10.1016/0029-5582(65)90862-X] that incorporates the pairing interaction. It is a schematic model that describes the interplay between particle-hole and pair correlations. It was proposed in the 1960s by D. Agassi as a model to simulate the properties of the quadrupole plus pairing model. Purpose: The aim of this work is to extend a previous study by Davis and Heiss [J. Phys. G: Nucl. Phys. 12, 805 (1986), 10.1088/0305-4616/12/9/006] generalizing the Agassi model and analyze in detail the phase diagram of the model as well as the different regions with coexistence of several phases. Method: We solve the model Hamiltonian through the Hartree-Fock-Bogoliubov (HFB) approximation, introducing two variational parameters that play the role of order parameters. We also compare the HFB calculations with the exact ones. Results: We obtain the phase diagram of the model and classify the order of the different quantum phase transitions appearing in the diagram. The phase diagram presents broad regions where several phases, up to three, coexist. Moreover, there is also a line and a point where four and five phases are degenerated, respectively. Conclusions: The phase diagram of the extended Agassi model presents a rich variety of phases. Phase coexistence is present in extended areas of the parameter space. The model could be an important tool for benchmarking novel many-body approximations.

Refined phase diagram of boron nitride

International Nuclear Information System (INIS)

Solozhenko, V.; Turkevich, V.Z.

1999-01-01

The equilibrium phase diagram of boron nitride thermodynamically calculated by Solozhenko in 1988 has been now refined on the basis of new experimental data on BN melting and extrapolation of heat capacities of BN polymorphs into high-temperature region using the adapted pseudo-Debye model. As compared with the above diagram, the hBN left-reversible cBN equilibrium line is displaced by 60 K toward higher temperatures. The hBN-cBN-L triple point has been calculated to be at 3480 ± 10 K and 5.9 ± 0.1 GPa, while the hBN-L-V triple point is at T = 3400 ± 20 K and p = 400 ± 20 Pa, which indicates that the region of thermodynamic stability of vapor in the BN phase diagram is extremely small. It has been found that the slope of the cBN melting curve is positive whereas the slope of hBN melting curve varies from positive between ambient pressure and 3.4 GPa to negative at higher pressures

({alpha},{eta}) phase diagrams in tilted chiral smectics

Energy Technology Data Exchange (ETDEWEB)

Rjili, M., E-mail: medrjili@yahoo.fr [Laboratoire de Physique de la Matiere Molle et de la Modelisation Electromagnetique, Faculte des Sciences de Tunis, Universite Tunis El Manar, 2092 El Manar Tunis (Tunisia); Marcerou, J.P., E-mail: marcerou@crpp-bordeaux.cnrs.fr [Centre de Recherches Paul Pascal, 115, Av. Albert-Schweitzer, 33600 Pessac (France); Gharbi, A.; Othman, T. [Laboratoire de Physique de la Matiere Molle et de la Modelisation Electromagnetique, Faculte des Sciences de Tunis, Universite Tunis El Manar, 2092 El Manar Tunis (Tunisia)

2013-02-01

The polymorphism of tilted chiral smectics liquid crystals is incredibly rich and encompasses many subphases such as SmC{sub A}{sup Low-Asterisk }; SmC{sub Fi1}{sup Low-Asterisk }; SmC{sub Fi2}{sup Low-Asterisk }; SmC{sup Low-Asterisk }; SmC{sub {alpha}}{sup Low-Asterisk }. The continuum theory established by Marcerou (2010) is used to derive an expression for the free energy density of those subphases. The minimization of this free energy is obtained through a combination of analytical and numerical methods. It leads to a phase diagram built in the ({alpha},{eta}) plane where {alpha} is local angular parameter and {eta} describes the variation of the temperature. From this graphical representation, many experimentally observed phase sequences of ferroelectric liquid crystals can be explained, even them including subphases which were recently observed like the SmC{sub 5}{sup Low-Asterisk} and the SmC{sub 6}{sup Low-Asterisk} ones. However, it should be emphasized that the details of predicted phase diagram are strongly dependent on the compound studied.

Phase diagrams of diluted transverse Ising nanowire

International Nuclear Information System (INIS)

Bouhou, S.; Essaoudi, I.; Ainane, A.; Saber, M.; Ahuja, R.; Dujardin, F.

2013-01-01

In this paper, the phase diagrams of diluted Ising nanowire consisting of core and surface shell coupling by J cs exchange interaction are studied using the effective field theory with a probability distribution technique, in the presence of transverse fields in the core and in the surface shell. We find a number of characteristic phenomena. In particular, the effect of concentration c of magnetic atoms, the exchange interaction core/shell, the exchange in surface and the transverse fields in core and in surface shell of phase diagrams are investigated. - Highlights: ► We use the EFT to investigate the phase diagrams of Ising transverse nanowire. ► Ferrimagnetic and ferromagnetic cases are investigated. ► The effects of the dilution and the transverse fields in core and shell are studied. ► Behavior of the transition temperature with the exchange interaction is given

Homotopy Diagrams of Algebras

Czech Academy of Sciences Publication Activity Database

Markl, Martin

2002-01-01

Roč. 69, - (2002), s. 161-180 ISSN 0009-725X. [Winter School "Geometry and Physics" /21./. Srní, 13.01.2001-20.01.2001] R&D Projects: GA ČR GA201/99/0675 Keywords : colored operad%cofibrant model%homotopy diagram Subject RIV: BA - General Mathematics

Random Young diagrams in a Rectangular Box

DEFF Research Database (Denmark)

Beltoft, Dan; Boutillier, Cédric; Enriquez, Nathanaël

We exhibit the limit shape of random Young diagrams having a distribution proportional to the exponential of their area, and confined in a rectangular box. The Ornstein-Uhlenbeck bridge arises from the fluctuations around the limit shape.......We exhibit the limit shape of random Young diagrams having a distribution proportional to the exponential of their area, and confined in a rectangular box. The Ornstein-Uhlenbeck bridge arises from the fluctuations around the limit shape....

Shear heating and metamorphism in subduction zones, 1. Thermal models

Science.gov (United States)

Kohn, M. J.; Castro, A. E.; Spear, F. S.

2017-12-01

Popular thermal-mechanical models of modern subduction systems are 100-500 °C colder at c. 50 km depth than pressure-temperature (P-T) conditions determined from exhumed metamorphic rocks. This discrepancy has been ascribed by some to profound bias in the rock record, i.e. metamorphic rocks reflect only anomalously warm subduction, not normal subduction. Accurately inferring subduction zone thermal structure, whether from models or rocks, is crucial for predicting depths of seismicity, fluid release, and sub-arc melting conditions. Here, we show that adding realistic shear stresses to thermal models implies P-T conditions quantitatively consistent with those recorded by exhumed metamorphic rocks, suggesting that metamorphic rock P-T conditions are not anomalously warm. Heat flow measurements from subduction zone fore-arcs typically indicate effective coefficients of friction (µ) ranging from 0.025 to 0.1. We included these coefficients of friction in analytical models of subduction zone interface temperatures. Using global averages of subducting plate age (50 Ma), subduction velocity (6 cm/yr), and subducting plate geometry (central Chile), temperatures at 50 km depth (1.5 GPa) increase by c. 200 °C for µ=0.025 to 700 °C for µ=0.1. However, at high temperatures, thermal softening will reduce frictional heating, and temperatures will not increase as much with depth. Including initial weakening of materials ranging from wet quartz (c. 300 °C) to diabase (c. 600 °C) in the analytical models produces concave-upward P-T distributions on P-T diagrams, with temperatures c. 100 to 500 °C higher than models with no shear heating. The absolute P-T conditions and concave-upward shape of the shear-heating + thermal softening models almost perfectly matches the distribution of P-T conditions derived from a compilation of exhumed metamorphic rocks. Numerical models of modern subduction zones that include shear heating also overlap metamorphic data. Thus, excepting the

Gravitational lensing of the CMB: A Feynman diagram approach

Directory of Open Access Journals (Sweden)

Elizabeth E. Jenkins

2014-09-01

Full Text Available We develop a Feynman diagram approach to calculating correlations of the Cosmic Microwave Background (CMB in the presence of distortions. As one application, we focus on CMB distortions due to gravitational lensing by Large Scale Structure (LSS. We study the Hu–Okamoto quadratic estimator for extracting lensing from the CMB and derive the noise of the estimator up to O(ϕ4 in the lensing potential ϕ. By identifying the diagrams responsible for the previously noted large O(ϕ4 term, we conclude that the lensing expansion does not break down. The convergence can be significantly improved by a reorganization of the ϕ expansion. Our approach makes it simple to obtain expressions for quadratic estimators based on any CMB channel, including many previously unexplored cases. We briefly discuss other applications to cosmology of this diagrammatic approach, such as distortions of the CMB due to patchy reionization, or due to Faraday rotation from primordial axion fields.

Formal Analysis Of Use Case Diagrams

Directory of Open Access Journals (Sweden)

Radosław Klimek

2010-01-01

Full Text Available Use case diagrams play an important role in modeling with UML. Careful modeling is crucialin obtaining a correct and efficient system architecture. The paper refers to the formalanalysis of the use case diagrams. A formal model of use cases is proposed and its constructionfor typical relationships between use cases is described. Two methods of formal analysis andverification are presented. The first one based on a states’ exploration represents a modelchecking approach. The second one refers to the symbolic reasoning using formal methodsof temporal logic. Simple but representative example of the use case scenario verification isdiscussed.

Phase Stability Diagrams for High Temperature Corrosion Processes

Directory of Open Access Journals (Sweden)

J. J. Ramos-Hernandez

2013-01-01

Full Text Available Corrosion phenomena of metals by fused salts depend on chemical composition of the melt and environmental conditions of the system. Detail knowledge of chemistry and thermodynamic of aggressive species formed during the corrosion process is essential for a better understanding of materials degradation exposed to high temperature. When there is a lack of kinetic data for the corrosion processes, an alternative to understand the thermodynamic behavior of chemical species is to utilize phase stability diagrams. Nowadays, there are several specialized software programs to calculate phase stability diagrams. These programs are based on thermodynamics of chemical reactions. Using a thermodynamic data base allows the calculation of different types of phase diagrams. However, sometimes it is difficult to have access to such data bases. In this work, an alternative way to calculate phase stability diagrams is presented. The work is exemplified in the Na-V-S-O and Al-Na-V-S-O systems. This system was chosen because vanadium salts is one of the more aggressive system for all engineering alloys, especially in those processes where fossil fuels are used.

Resonant count diagram and solar g mode oscillations

International Nuclear Information System (INIS)

Guenther, D.B.; Demarque, P.

1984-01-01

Evidence is provided to support the hypothesis that, because of the particular frequency separations of the solar g modes, resonant three-wave interactions stimulate only a selected few g modes. A resonant count diagram was obtained by plotting the total number of possible resonant three-wave interactions or a given beat frequency against the inverse of the beat frequency (the beat period), within a given frequency tolerance. The 1 = 1, 2, 3, 4 g modes calculated by Christensen-Dalsgaard, Gough and Morgan (1979) for a standard model of the Sun were used. The diagram has a significant peak at 160 minutes as well as other peaks at longer periods. The g modes that Delache and Scherrer (1983) tentatively identified from the Crimea-Stanford data were also plotted. These modes were found to correspond with the other peaks in the diagram. This coincidence between the observed g modes and the peaks in the resonant count diagram suggest that the observed g modes do owe their observability to resonant three-wave interactions

Solid gas reaction phase diagram under high gas pressure

International Nuclear Information System (INIS)

Ishizaki, K.

1992-01-01

This paper reports that to evaluate which are the stable phases under high gas pressure conditions, a solid-gas reaction phase diagram under high gas pressure (HIP phase diagram) has been proposed by the author. The variables of the diagram are temperature, reactant gas partial pressure and total gas pressure. Up to the present time the diagrams have been constructed using isobaric conditions. In this work, the stable phases for a real HIP process were evaluated assuming an isochoric condition. To understand the effect of the total gas pressure on stability is of primary importance. Two possibilities were considered and evaluated, those are: the total gas pressure acts as an independent variable, or it only affects the fugacity values. The results of this work indicate that the total gas pressure acts as an independent variable, and in turn also affects the fugacity values

Equational binary decision diagrams

NARCIS (Netherlands)

J.F. Groote (Jan Friso); J.C. van de Pol (Jaco)

2000-01-01

textabstractWe incorporate equations in binary decision diagrams (BDD). The resulting objects are called EQ-BDDs. A straightforward notion of ordered EQ-BDDs (EQ-OBDD) is defined, and it is proved that each EQ-BDD is logically equivalent to an EQ-OBDD. Moreover, on EQ-OBDDs satisfiability and

On the Impact of Diagram Layout: How Are Models Actually Read?

DEFF Research Database (Denmark)

Störrle, Harald; Baltsen, Nick; Christoffersen, Henrik

2014-01-01

This poster presents the latest results from a very large eye tracking study (n=29) that explores how modelers read UML diagrams. We find that various factors like layout quality, modeler experience, and diagram type lead to significant differences in diagram reading strategies. We derive elements...

A Three-dimensional Topological Model of Ternary Phase Diagram

International Nuclear Information System (INIS)

Mu, Yingxue; Bao, Hong

2017-01-01

In order to obtain a visualization of the complex internal structure of ternary phase diagram, the paper realized a three-dimensional topology model of ternary phase diagram with the designed data structure and improved algorithm, under the guidance of relevant theories of computer graphics. The purpose of the model is mainly to analyze the relationship between each phase region of a ternary phase diagram. The model not only obtain isothermal section graph at any temperature, but also extract a particular phase region in which users are interested. (paper)

Finding and Accessing Diagrams in Biomedical Publications

OpenAIRE

Kuhn, Tobias; Luong, ThaiBinh; Krauthammer, Michael

2012-01-01

Complex relationships in biomedical publications are often communicated by diagrams such as bar and line charts, which are a very effective way of summarizing and communicating multi-faceted data sets. Given the ever-increasing amount of published data, we argue that the precise retrieval of such diagrams is of great value for answering specific and otherwise hard-to-meet information needs. To this end, we demonstrate the use of advanced image processing and classification for identifying bar...

Phase diagrams of diluted transverse Ising nanowire

Energy Technology Data Exchange (ETDEWEB)

Bouhou, S.; Essaoudi, I. [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Ainane, A., E-mail: ainane@pks.mpg.de [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Max-Planck-Institut für Physik Complexer Systeme, Nöthnitzer Str. 38 D-01187 Dresden (Germany); Saber, M. [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Max-Planck-Institut für Physik Complexer Systeme, Nöthnitzer Str. 38 D-01187 Dresden (Germany); Ahuja, R. [Condensed Matter Theory Group, Department of Physics and Astronomy, Uppsala University, 75120 Uppsala (Sweden); Dujardin, F. [Laboratoire de Chimie et Physique des Milieux Complexes (LCPMC), Institut de Chimie, Physique et Matériaux (ICPM), 1 Bd. Arago, 57070 Metz (France)

2013-06-15

In this paper, the phase diagrams of diluted Ising nanowire consisting of core and surface shell coupling by J{sub cs} exchange interaction are studied using the effective field theory with a probability distribution technique, in the presence of transverse fields in the core and in the surface shell. We find a number of characteristic phenomena. In particular, the effect of concentration c of magnetic atoms, the exchange interaction core/shell, the exchange in surface and the transverse fields in core and in surface shell of phase diagrams are investigated. - Highlights: ► We use the EFT to investigate the phase diagrams of Ising transverse nanowire. ► Ferrimagnetic and ferromagnetic cases are investigated. ► The effects of the dilution and the transverse fields in core and shell are studied. ► Behavior of the transition temperature with the exchange interaction is given.

The Diagram as Story: Unfolding the Event-Structure of the Mathematical Diagram

Science.gov (United States)

de Freitas, Elizabeth

2012-01-01

This paper explores the role of narrative in decoding diagrams. I focus on two fundamental facets of narrative: (1) the recounting of causally related sequences of events, and (2) the positioning of the narrator through point-of-view and voice. In the first two sections of the paper I discuss philosophical and semiotic frameworks for making sense…

Lean premixed reacting flows with swirl and wall-separation zones in a contracting chamber

Science.gov (United States)

Zhang, Yuxin; Rusak, Zvi; Wang, Shixiao

2017-11-01

Low Mach number lean premixed reacting swirling flows with wall-separation zones in a contracting circular finite-length open chamber are studied. Assuming a complete reaction with high activation energy and chemical equilibrium behind the reaction zone, a nonlinear partial differential equation is derived for the solution of the flow stream function behind the reaction zone in terms of the inlet total enthalpy for a reacting flow, specific entropy and the circulation functions. Bifurcation diagrams of steady flows are described as the inlet swirl level is increased at fixed chamber contraction and reaction heat release. The approach is applied to an inlet solid-body rotation flow with constant profiles of the axial velocity, temperature and mixture reactant mass fraction. The computed results provide predictions of the critical inlet swirl levels for the first appearance of wall-separation states and for the size of the separation zone as a function of the inlet swirl ratio, Mach number, chamber contraction and heat release of the reaction. The methodology developed in this paper provides a theoretical feasibility for the development of the technology of swirl-assisted combustion where the reaction zone is supported and stabilized by a wall-separation zone.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

Science.gov (United States)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-04-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

Investigation of Hardness Change for Spot Welded Tailored Blank in Hot Stamping Using CCT and Deformation-CCT Diagrams

Science.gov (United States)

Yogo, Yasuhiro; Kurato, Nozomi; Iwata, Noritoshi

2018-06-01

When an outer panel of a B-pillar is manufactured with the hot stamping process, reinforcements are spot welded on its inner side. Before reinforcements are added, the microstructure of the outer panel is martensite. However, reheating during spot welding changes the martensite to ferrite, which has a lower hardness in the heat-affected zone than in other areas. If spot welding is conducted before hot stamping for making a spot welded tailored blank, the microstructure in the spot welded tailored blank after hot stamping is martensite. This sequence of processes avoids hardness reduction due to spot welding. In this study, the hardness and microstructure around spot welded parts of the tailored blank were investigated. The results clearly showed that areas close to the spot welded parts are severely stretched during hot stamping. In addition, stretching suppresses the martensitic phase transformation and reduces the hardness. To characterize this phenomenon, a simulation was conducted that considered the effects of pre-strain on the phase transformation. A continuous cooling transformation (CCT) diagram and a deformation continuous cooling transformation (DCCT) diagram were made in order to quantify the effect of the cooling rate and pre-strain on the phase transformation and hardness. The hardness was then calculated using the experimentally measured CCT and DCCT diagrams and the finite element analysis results. The calculated hardness was compared with the experimental hardness. Good agreement was found between the calculated and experimental results.

Hubble Diagram Test of Expanding and Static Cosmological Models: The Case for a Slowly Expanding Flat Universe

Directory of Open Access Journals (Sweden)

Laszlo A. Marosi

2013-01-01

Full Text Available We present a new redshift (RS versus photon travel time ( test including 171 supernovae RS data points. We extended the Hubble diagram to a range of z = 0,0141–8.1 in the hope that at high RSs, the fitting of the calculated RS/ diagrams to the observed RS data would, as predicted by different cosmological models, set constraints on alternative cosmological models. The Lambda cold dark matter (ΛCDM, the static universe model, and the case for a slowly expanding flat universe (SEU are considered. We show that on the basis of the Hubble diagram test, the static and the slowly expanding models are favored.

Random matrix models for phase diagrams

International Nuclear Information System (INIS)

Vanderheyden, B; Jackson, A D

2011-01-01

We describe a random matrix approach that can provide generic and readily soluble mean-field descriptions of the phase diagram for a variety of systems ranging from quantum chromodynamics to high-T c materials. Instead of working from specific models, phase diagrams are constructed by averaging over the ensemble of theories that possesses the relevant symmetries of the problem. Although approximate in nature, this approach has a number of advantages. First, it can be useful in distinguishing generic features from model-dependent details. Second, it can help in understanding the 'minimal' number of symmetry constraints required to reproduce specific phase structures. Third, the robustness of predictions can be checked with respect to variations in the detailed description of the interactions. Finally, near critical points, random matrix models bear strong similarities to Ginsburg-Landau theories with the advantage of additional constraints inherited from the symmetries of the underlying interaction. These constraints can be helpful in ruling out certain topologies in the phase diagram. In this Key Issues Review, we illustrate the basic structure of random matrix models, discuss their strengths and weaknesses, and consider the kinds of system to which they can be applied.

Colour-magnitude diagram of NGC 5053

Energy Technology Data Exchange (ETDEWEB)

Walker, M F; Pike, C D [California Univ., Santa Cruz (USA). Lick Observatory; McGee, J D

1976-06-01

The colour-magnitude diagram of NGC 5053 has been derived to V = 21.1 from photographic and electronographic observations. The electronographic observations were obtained with an experimental Spectracon image-converter, having photocathode and exit window dimensions of 20 x 30 mm, mounted at the prime-focus of the 120-in. Lick reflector. The photographic observations were obtained with the 20-in. Carnegie astrograph and the 36-in. Crossley reflector. The colour-magnitude diagram resembles that of M92, with the difference that a red horizontal branch is more pronounced than the asymptotic branch in NGC 5053. The topology of the horizontal branch is that of clusters with an intermediate metal content and is thus at variance with the mean period of the RR Lyr stars and the unreddened colour of the subgiant branch read at the magnitude level of the horizontal branch, both of which would indicate an extremely low metal content. If comparison of the colour-magnitude diagrams of NGC 5053 and M92 is valid, then the reddening of NGC 5053 is Esub(B-V) = 0.02 and the apparent distance modulus is m-M = 16.08 +- 0.08.

Reactome diagram viewer: data structures and strategies to boost performance.

Science.gov (United States)

Fabregat, Antonio; Sidiropoulos, Konstantinos; Viteri, Guilherme; Marin-Garcia, Pablo; Ping, Peipei; Stein, Lincoln; D'Eustachio, Peter; Hermjakob, Henning

2018-04-01

Reactome is a free, open-source, open-data, curated and peer-reviewed knowledgebase of biomolecular pathways. For web-based pathway visualization, Reactome uses a custom pathway diagram viewer that has been evolved over the past years. Here, we present comprehensive enhancements in usability and performance based on extensive usability testing sessions and technology developments, aiming to optimize the viewer towards the needs of the community. The pathway diagram viewer version 3 achieves consistently better performance, loading and rendering of 97% of the diagrams in Reactome in less than 1 s. Combining the multi-layer html5 canvas strategy with a space partitioning data structure minimizes CPU workload, enabling the introduction of new features that further enhance user experience. Through the use of highly optimized data structures and algorithms, Reactome has boosted the performance and usability of the new pathway diagram viewer, providing a robust, scalable and easy-to-integrate solution to pathway visualization. As graph-based visualization of complex data is a frequent challenge in bioinformatics, many of the individual strategies presented here are applicable to a wide range of web-based bioinformatics resources. Reactome is available online at: https://reactome.org. The diagram viewer is part of the Reactome pathway browser (https://reactome.org/PathwayBrowser/) and also available as a stand-alone widget at: https://reactome.org/dev/diagram/. The source code is freely available at: https://github.com/reactome-pwp/diagram. fabregat@ebi.ac.uk or hhe@ebi.ac.uk. Supplementary data are available at Bioinformatics online.

Limits of Voronoi Diagrams

NARCIS (Netherlands)

Lindenbergh, R.C.

2002-01-01

The classic Voronoi diagram of a configuration of distinct points in the plane associates to each point that part of the plane that is closer to the point than to any other point in the configuration. In this thesis we no longer require all points to be distinct. After the introduction in

Unified Phase Diagram for Iron-Based Superconductors.

Science.gov (United States)

Gu, Yanhong; Liu, Zhaoyu; Xie, Tao; Zhang, Wenliang; Gong, Dongliang; Hu, Ding; Ma, Xiaoyan; Li, Chunhong; Zhao, Lingxiao; Lin, Lifang; Xu, Zhuang; Tan, Guotai; Chen, Genfu; Meng, Zi Yang; Yang, Yi-Feng; Luo, Huiqian; Li, Shiliang

2017-10-13

High-temperature superconductivity is closely adjacent to a long-range antiferromagnet, which is called a parent compound. In cuprates, all parent compounds are alike and carrier doping leads to superconductivity, so a unified phase diagram can be drawn. However, the properties of parent compounds for iron-based superconductors show significant diversity and both carrier and isovalent dopings can cause superconductivity, which casts doubt on the idea that there exists a unified phase diagram for them. Here we show that the ordered moments in a variety of iron pnictides are inversely proportional to the effective Curie constants of their nematic susceptibility. This unexpected scaling behavior suggests that the magnetic ground states of iron pnictides can be achieved by tuning the strength of nematic fluctuations. Therefore, a unified phase diagram can be established where superconductivity emerges from a hypothetical parent compound with a large ordered moment but weak nematic fluctuations, which suggests that iron-based superconductors are strongly correlated electron systems.

Unified Phase Diagram for Iron-Based Superconductors

Science.gov (United States)

Gu, Yanhong; Liu, Zhaoyu; Xie, Tao; Zhang, Wenliang; Gong, Dongliang; Hu, Ding; Ma, Xiaoyan; Li, Chunhong; Zhao, Lingxiao; Lin, Lifang; Xu, Zhuang; Tan, Guotai; Chen, Genfu; Meng, Zi Yang; Yang, Yi-feng; Luo, Huiqian; Li, Shiliang

2017-10-01

High-temperature superconductivity is closely adjacent to a long-range antiferromagnet, which is called a parent compound. In cuprates, all parent compounds are alike and carrier doping leads to superconductivity, so a unified phase diagram can be drawn. However, the properties of parent compounds for iron-based superconductors show significant diversity and both carrier and isovalent dopings can cause superconductivity, which casts doubt on the idea that there exists a unified phase diagram for them. Here we show that the ordered moments in a variety of iron pnictides are inversely proportional to the effective Curie constants of their nematic susceptibility. This unexpected scaling behavior suggests that the magnetic ground states of iron pnictides can be achieved by tuning the strength of nematic fluctuations. Therefore, a unified phase diagram can be established where superconductivity emerges from a hypothetical parent compound with a large ordered moment but weak nematic fluctuations, which suggests that iron-based superconductors are strongly correlated electron systems.

40 CFR 720.45 - Information that must be included in the notice form.

Science.gov (United States)

2010-07-01

... manufactured, processed, or used. (2) A process description of each manufacture, processing, and use operation which includes a diagram of the major unit operations and chemical conversions, the identity and entry... composition that can be represented by a specific, complete chemical structure diagram (a Class 1 substance...

Parapapillary atrophy: histological gamma zone and delta zone.

Directory of Open Access Journals (Sweden)

Jost B Jonas

Full Text Available BACKGROUND: To examine histomorphometrically the parapapillary region in human eyes. METHODOLOGY/PRINCIPAL FINDINGS: The histomorphometric study included 65 human globes (axial length:21-37 mm. On anterior-posterior histological sections, we measured the distance Bruch's membrane end (BME-optic nerve margin ("Gamma zone", BME-retinal pigment epithelium (RPE ("Beta zone", BME-beginning of non-occluded choriocapillaris, and BME-beginning of photoreceptor layer. "Delta zone" was defined as part of gamma zone in which blood vessels of at least 50 µm diameter were not present over a length of >300 µm. Beta zone (mean length:0.35±0.52 mm was significantly (P = 0.01 larger in the glaucoma group than in the non-glaucomatous group. It was not significantly (P = 0.28 associated with axial length. Beta zone was significantly (P = 0.004 larger than the region with occluded choriocapillaris. Gamma zone (mean length:0.63±1.25 mm was associated with axial length (P50 µm diameter within gamma zone was present only in highly axially elongated globes and was not related with glaucoma. Beta zone (Bruch's membrane without RPE was correlated with glaucoma but not with globe elongation. Since the region with occluded choriocapillaris was smaller than beta zone, complete loss of RPE may have occurred before complete choriocapillaris closure.

Calculation of Energy Diagram of Asymmetric Graded-Band-Gap Semiconductor Superlattices.

Science.gov (United States)

Monastyrskii, Liubomyr S; Sokolovskii, Bogdan S; Alekseichyk, Mariya P

2017-12-01

The paper theoretically investigates the peculiarities of energy diagram of asymmetric graded-band-gap superlattices with linear coordinate dependences of band gap and electron affinity. For calculating the energy diagram of asymmetric graded-band-gap superlattices, linearized Poisson's equation has been solved for the two layers forming a period of the superlattice. The obtained coordinate dependences of edges of the conduction and valence bands demonstrate substantial transformation of the shape of the energy diagram at changing the period of the lattice and the ratio of width of the adjacent layers. The most marked changes in the energy diagram take place when the period of lattice is comparable with the Debye screening length. In the case when the lattice period is much smaller that the Debye screening length, the energy diagram has the shape of a sawtooth-like pattern.

RNA secondary structure diagrams for very large molecules: RNAfdl

DEFF Research Database (Denmark)

Hecker, Nikolai; Wiegels, Tim; Torda, Andrew E.

2013-01-01

There are many programs that can read the secondary structure of an RNA molecule and draw a diagram, but hardly any that can cope with 10 3 bases. RNAfdl is slow but capable of producing intersection-free diagrams for ribosome-sized structures, has a graphical user interface for adjustments...

Automated Methodologies for the Design of Flow Diagrams for Development and Maintenance Activities

Science.gov (United States)

Shivanand M., Handigund; Shweta, Bhat

The Software Requirements Specification (SRS) of the organization is a text document prepared by strategic management incorporating the requirements of the organization. These requirements of ongoing business/ project development process involve the software tools, the hardware devices, the manual procedures, the application programs and the communication commands. These components are appropriately ordered for achieving the mission of the concerned process both in the project development and the ongoing business processes, in different flow diagrams viz. activity chart, workflow diagram, activity diagram, component diagram and deployment diagram. This paper proposes two generic, automatic methodologies for the design of various flow diagrams of (i) project development activities, (ii) ongoing business process. The methodologies also resolve the ensuing deadlocks in the flow diagrams and determine the critical paths for the activity chart. Though both methodologies are independent, each complements other in authenticating its correctness and completeness.

The Fishbone diagram to identify, systematize and analyze the sources of general purpose technologies

OpenAIRE

COCCIA, Mario

2017-01-01

Abstract. This study suggests the fishbone diagram for technological analysis. Fishbone diagram (also called Ishikawa diagrams or cause-and-effect diagrams) is a graphical technique to show the several causes of a specific event or phenomenon. In particular, a fishbone diagram (the shape is similar to a fish skeleton) is a common tool used for a cause and effect analysis to identify a complex interplay of causes for a specific problem or event. The fishbone diagram can be a comprehensive theo...

Quantum MHV Diagrams

OpenAIRE

Brandhuber, Andreas; Travaglini, Gabriele

2006-01-01

Over the past two years, the use of on-shell techniques has deepened our understanding of the S-matrix of gauge theories and led to the calculation of many new scattering amplitudes. In these notes we review a particular on-shell method developed recently, the quantum MHV diagrams, and discuss applications to one-loop amplitudes. Furthermore, we briefly discuss the application of D-dimensional generalised unitarity to the calculation of scattering amplitudes in non-supersymmetric Yang-Mills.

Theoretical Prediction of Melting Relations in the Deep Mantle: the Phase Diagram Approach

Science.gov (United States)

Belmonte, D.; Ottonello, G. A.; Vetuschi Zuccolini, M.; Attene, M.

2016-12-01

Despite the outstanding progress in computer technology and experimental facilities, understanding melting phase relations in the deep mantle is still an open challenge. In this work a novel computational scheme to predict melting relations at HP-HT by a combination of first principles DFT calculations, polymer chemistry and equilibrium thermodynamics is presented and discussed. The adopted theoretical framework is physically-consistent and allows to compute multi-component phase diagrams relevant to Earth's deep interior in a broad range of P-T conditions by a convex-hull algorithm for Gibbs free energy minimisation purposely developed for high-rank simplexes. The calculated phase diagrams are in turn used as a source of information to gain new insights on the P-T-X evolution of magmas in the deep mantle, providing some thermodynamic constraints to both present-day and early Earth melting processes. High-pressure melting curves of mantle silicates are also obtained as by-product of phase diagram calculation. Application of the above method to the MgO-Al2O3-SiO2 (MAS) ternary system highlights as pressure effects are not only able to change the nature of melting of some minerals (like olivine and pyroxene) from eutectic to peritectic (and vice versa), but also simplify melting relations by drastically reducing the number of phases with a primary phase field at HP-HT conditions. It turns out that mineral phases like Majorite-Pyrope garnet and Anhydrous Phase B (Mg14Si5O24), which are often disregarded in modelling melting processes of mantle assemblages, are stable phases at solidus or liquidus conditions in a P-T range compatible with the mantle transition zone (i.e. P = 16 - 23 GPa and T = 2200 - 2700 °C) when their thermodynamic and thermophysical properties are properly assessed. Financial support to the Senior Author (D.B.) during his stay as Invited Scientist at the Institut de Physique du Globe de Paris (IPGP, Paris) is warmly acknowledged.

Phase diagrams from ab-initio calculations: Re-W and Fe-B

Energy Technology Data Exchange (ETDEWEB)

Hammerschmidt, Thomas; Bialon, Arthur; Palumbo, Mauro; Fries, Suzana G.; Drautz, Ralf [ICAMS, Ruhr-Universitaet Bochum (Germany)

2011-07-01

The CALPHAD (CaLculation of Phase Diagrams) method relies on Gibbs energy databases and is of limited predictive power in cases where only limited experimental data is available for constructing the Gibbs energy databases. This is problematic for, e.g., the calculation of the phase transformation kinetics within phase field simulations that not only require the thermodynamic equilibrium data but also information on metastable phases. Such information is difficult to obtain directly from experiment but ab-initio calculations may supplement experimental databases as they comprise metastable phases and arbitrary chemical compositions. We present simulations for two prototypical systems: Re-W and Fe-B. For both systems we calculate the heat of formation for an extensive set of structures using ab-initio calculations and employ the total energies in CALPHAD in order to determine the corresponding phase diagrams. We account for the configurational entropy within the Bragg-Williams approximation and neglect the phenomenological excess-term that is commonly used in CALPHAD as well as the contribution of phonons and electronic excitations to the free energy. According to our calculations the complex intermetallic phases in Re-W are stabilized by the configurational entropy. For Fe-B, we calculate metastable and stable phase diagrams including recently predicted new stable phases.

Heuristic Diagrams as a Tool to Teach History of Science

Science.gov (United States)

Chamizo, José A.

2012-05-01

The graphic organizer called here heuristic diagram as an improvement of Gowin's Vee heuristic is proposed as a tool to teach history of science. Heuristic diagrams have the purpose of helping students (or teachers, or researchers) to understand their own research considering that asks and problem-solving are central to scientific activity. The left side originally related in Gowin's Vee with philosophies, theories, models, laws or regularities now agrees with Toulmin's concepts (language, models as representation techniques and application procedures). Mexican science teachers without experience in science education research used the heuristic diagram to learn about the history of chemistry considering also in the left side two different historical times: past and present. Through a semantic differential scale teachers' attitude to the heuristic diagram was evaluated and its usefulness was demonstrated.

Bayesian Networks and Influence Diagrams

DEFF Research Database (Denmark)

Kjærulff, Uffe Bro; Madsen, Anders Læsø

Bayesian Networks and Influence Diagrams: A Guide to Construction and Analysis, Second Edition, provides a comprehensive guide for practitioners who wish to understand, construct, and analyze intelligent systems for decision support based on probabilistic networks. This new edition contains six new...

INFRARED COLOR-COLOR DIAGRAMS FOR AGB STARS

Directory of Open Access Journals (Sweden)

Kyung-Won Suh

2007-09-01

Full Text Available We present infrared color-color diagrams of AGB stars from the observations at near and mid infrared bands. We compile the observations for hundreds of OH/IR stars and carbon stars using the data from the Midcourse Space Experiment (MSX, the two micron sky survey (2MASS, and the IRAS point source catalog (PSC. We compare the observations with the theoretical evolutionary tracks of AGB stars. From the new observational data base and the theoretical evolution tracks, we discuss the meaning of the infrared color-color diagrams at different wavelengths.

Examining competing hypotheses for the effects of diagrams on recall for text.

Science.gov (United States)

Ortegren, Francesca R; Serra, Michael J; England, Benjamin D

2015-01-01

Supplementing text-based learning materials with diagrams typically increases students' free recall and cued recall of the presented information. In the present experiments, we examined competing hypotheses for why this occurs. More specifically, although diagrams are visual, they also serve to repeat information from the text they accompany. Both visual presentation and repetition are known to aid students' recall of information. To examine to what extent diagrams aid recall because they are visual or repetitive (or both), we had college students in two experiments (n = 320) read a science text about how lightning storms develop before completing free-recall and cued-recall tests over the presented information. Between groups, we manipulated the format and repetition of target pieces of information in the study materials using a 2 (visual presentation of target information: diagrams present vs. diagrams absent) × 2 (repetition of target information: present vs. absent) between-participants factorial design. Repetition increased both the free recall and cued recall of target information, and this occurred regardless of whether that repetition was in the form of text or a diagram. In contrast, the visual presentation of information never aided free recall. Furthermore, visual presentation alone did not significantly aid cued recall when participants studied the materials once before the test (Experiment 1) but did when they studied the materials twice (Experiment 2). Taken together, the results of the present experiments demonstrate the important role of repetition (i.e., that diagrams repeat information from the text) over the visual nature of diagrams in producing the benefits of diagrams for recall.

On Hardy's paradox, weak measurements, and multitasking diagrams

International Nuclear Information System (INIS)

Meglicki, Zdzislaw

2011-01-01

We discuss Hardy's paradox and weak measurements by using multitasking diagrams, which are introduced to illustrate the progress of quantum probabilities through the double interferometer system. We explain how Hardy's paradox is avoided and elaborate on the outcome of weak measurements in this context. -- Highlights: → Hardy's paradox explained and eliminated. → Weak measurements: what is really measured? → Multitasking diagrams: introduced and used to discuss quantum mechanical processes.

On the phase diagram of non-spherical nanoparticles

CERN Document Server

Wautelet, M; Hecq, M

2003-01-01

The phase diagram of nanoparticles is known to be a function of their size. In the literature, this is generally demonstrated for cases where their shape is spherical. Here, it is shown theoretically that the phase diagram of non-spherical particles may be calculated from the spherical case, at the same surface area/volume ratio, both with and without surface segregation, provided the surface tension is considered to be isotropic.

Bifurcation diagram features of a dc-dc converter under current-mode control

International Nuclear Information System (INIS)

Ruzbehani, Mohsen; Zhou Luowei; Wang Mingyu

2006-01-01

A common tool for analysis of the systems dynamics when the system has chaotic behaviour is the bifurcation diagram. In this paper, the bifurcation diagram of an ideal model of a dc-dc converter under current-mode control is analysed. Algebraic relations that give the critical points locations and describe the pattern of the bifurcation diagram are derived. It is shown that these simple algebraic and geometrical relations are responsible for the complex pattern of the bifurcation diagrams in such circuits. More explanation about the previously observed properties and introduction of some new ones are exposited. In addition, a new three-dimensional bifurcation diagram that can give better imagination of the parameters role is introduced

Diagram of Calcium Movement in the Human Body

Science.gov (United States)

2002-01-01

This diagram shows the normal pathways of calcium movement in the body and indicates changes (green arrows) seen during preliminary space flight experiments. Calcium plays a central role because 1) it gives strength and structure to bone and 2) all types of cells require it to function normally. To better understand how and why weightlessness induces bone loss, astronauts have participated in a study of calcium kinetics -- that is, the movement of calcium through the body, including absorption from food, and its role in the formation and breakdown of bone.

DIAGRAM SOLVE THE USE OF SIMULINK BLOCK DIAGRAM TO SOLVE MATHEMA THEMATICAL CONTROL EQU MATHEMATICAL MODELS AND CONTROL EQUATIONS

Directory of Open Access Journals (Sweden)

N.M. Ghasem

2003-12-01

Full Text Available In this paper, the simulink block diagram is used to solve a model consists of a set of ordinary differential and algebraic equations to control the temperature inside a simple stirred tank heater. The flexibility of simulink block diagram gives students a better understanding of the control systems. The simulink also allows solution of mathematical models and easy visualization of the system variables. A polyethylene fluidized bed reactor is considered as an industrial example and the effect of the Proportional, Integral and Derivative control policy is presented for comparison.

Electroweak penguin diagrams and two-body B decays

International Nuclear Information System (INIS)

Gronau, M.; Hernandez, O.F.; London, D.; Rosner, J.L.

1995-01-01

We discuss the role of electroweak penguin diagrams in B decays to two light pseudoscalar mesons. We confirm that the extraction of the weak phase α through the isospin analysis involving B→ππ decays is largely unaffected by such operators. However, the methods proposed to obtain weak and strong phases by relating B→ππ, B→πK, and B→K bar K decays through flavor SU(3) will be invalidated if eletroweak penguin diagrams are large. We show that, although the introduction of electroweak penguin contributions introduces no new amplitudes of flavor SU(3), there are a number of ways to experimentally measure the size of such effects. Finally, using SU(3) amplitude relations we present a new way of measuring the weak angle γ which holds even in the presence of electroweak penguin diagrams

Anytime decision making based on unconstrained influence diagrams

DEFF Research Database (Denmark)

Luque, Manuel; Nielsen, Thomas Dyhre; Jensen, Finn Verner

2016-01-01

. This paper addresses this problem by proposing an anytime algorithm that at any time provides a qualified recommendation for the first decisions of the problem. The algorithm performs a heuristic-based search in a decision tree representation of the problem. We provide a framework for analyzing......Unconstrained influence diagrams extend the language of influence diagrams to cope with decision problems in which the order of the decisions is unspecified. Thus, when solving an unconstrained influence diagram we not only look for an optimal policy for each decision, but also for a so-called step......-policy specifying the next decision given the observations made so far. However, due to the complexity of the problem, temporal constraints can force the decision maker to act before the solution algorithm has finished, and, in particular, before an optimal policy for the first decision has been computed...

A Hubble Diagram for Quasars

Directory of Open Access Journals (Sweden)

Susanna Bisogni

2018-01-01

Full Text Available The cosmological model is at present not tested between the redshift of the farthest observed supernovae (z ~ 1.4 and that of the Cosmic Microwave Background (z ~ 1,100. Here we introduce a new method to measure the cosmological parameters: we show that quasars can be used as “standard candles” by employing the non-linear relation between their intrinsic UV and X-ray emission as an absolute distance indicator. We built a sample of ~1,900 quasars with available UV and X-ray observations, and produced a Hubble Diagram up to z ~ 5. The analysis of the quasar Hubble Diagram, when used in combination with supernovae, provides robust constraints on the matter and energy content in the cosmos. The application of this method to forthcoming, larger quasar samples, will also provide tight constraints on the dark energy equation of state and its possible evolution with time.

Impact of Diagrams on Recalling Sequential Elements in Expository Texts.

Science.gov (United States)

Guri-Rozenblit, Sarah

1988-01-01

Examines the instructional effectiveness of abstract diagrams on recall of sequential relations in social science textbooks. Concludes that diagrams assist significantly the recall of sequential relations in a text and decrease significantly the rate of order mistakes. (RS)

A LaTeX graphics routine for drawing Feynman diagrams

International Nuclear Information System (INIS)

Levine, M.J.S.

1990-01-01

FEYNMAN is a LaTeX macropackage which allows the user to construct a versatile range of Feynman diagrams within the text of a document. Diagrams of publication quality may be drawn with relative ease and rapidity. (orig.)

Louisiana Speaks Regional Plan Vision Special Economic Zones, UTM Zone 15N NAD83, Louisiana Recovery Authority (2007), [louisiana_speaks_vision_special_economic_zones

Data.gov (United States)

Louisiana Geographic Information Center — This GIS shapefile data illustrates special economic zones included in the Louisiana Speaks Regional Plan Vision. Special economic zones include existing national,...

Interactive Land-Use Optimization Using Laguerre Voronoi Diagram with Dynamic Generating Point Allocation

Science.gov (United States)

Chaidee, S.; Pakawanwong, P.; Suppakitpaisarn, V.; Teerasawat, P.

2017-09-01

In this work, we devise an efficient method for the land-use optimization problem based on Laguerre Voronoi diagram. Previous Voronoi diagram-based methods are more efficient and more suitable for interactive design than discrete optimization-based method, but, in many cases, their outputs do not satisfy area constraints. To cope with the problem, we propose a force-directed graph drawing algorithm, which automatically allocates generating points of Voronoi diagram to appropriate positions. Then, we construct a Laguerre Voronoi diagram based on these generating points, use linear programs to adjust each cell, and reconstruct the diagram based on the adjustment. We adopt the proposed method to the practical case study of Chiang Mai University's allocated land for a mixed-use complex. For this case study, compared to other Voronoi diagram-based method, we decrease the land allocation error by 62.557 %. Although our computation time is larger than the previous Voronoi-diagram-based method, it is still suitable for interactive design.

Diagram, Gesture, Agency: Theorizing Embodiment in the Mathematics Classroom

Science.gov (United States)

de Freitas, Elizabeth; Sinclair, Nathalie

2012-01-01

In this paper, we use the work of philosopher Gilles Chatelet to rethink the gesture/diagram relationship and to explore the ways mathematical agency is constituted through it. We argue for a fundamental philosophical shift to better conceptualize the relationship between gesture and diagram, and suggest that such an approach might open up new…

Influence of different cooling rates on the microstructure of the HAZ and welding CCT diagram of CLAM steel

Energy Technology Data Exchange (ETDEWEB)

Zheng Shuhui, E-mail: shzheng@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Wu Qingsheng [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); Huang Qunying [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui, 230027 (China); Liu Shaojun; Han Yangyang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui, 230031 (China)

2011-10-15

The evolution of microstructure in the weld HAZ (Heat Affected Zone) under welding thermal cycle was simulated by Gleeble-1500. The microstructures and properties of HAZ at different cooling rates were investigated by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness test. The results showed that when the cooling rates ranged from 3600 K/min to 60 K/min, fully martensitic transformations were achieved, and the cooling rates had little influence on the microstructure and microhardness of martensite. The maximum cooling rate to form ferrite was 60 K/min. When the cooling rates ranged from 60 K/min to 1 K/min, the microhardness of the HAZ began to decrease due to the presence of ferrite, and the lath sizes grew up to 0.13-0.15 {mu}m. The critical cooling rate to gain fully ferrite was found to be slower than 1 K/min. The welding CCT diagram of CLAM steel was constructed and it showed that there were ferrite and martensite transformation regions only. The diagram made it possible to predict the microstructures and properties of HAZ and became an important tool to evaluate weldability of CLAM steel.

Influence of different cooling rates on the microstructure of the HAZ and welding CCT diagram of CLAM steel

International Nuclear Information System (INIS)

Zheng Shuhui; Wu Qingsheng; Huang Qunying; Liu Shaojun; Han Yangyang

2011-01-01

The evolution of microstructure in the weld HAZ (Heat Affected Zone) under welding thermal cycle was simulated by Gleeble-1500. The microstructures and properties of HAZ at different cooling rates were investigated by optical microscopy (OM), scanning electron microscopy (SEM) and microhardness test. The results showed that when the cooling rates ranged from 3600 K/min to 60 K/min, fully martensitic transformations were achieved, and the cooling rates had little influence on the microstructure and microhardness of martensite. The maximum cooling rate to form ferrite was 60 K/min. When the cooling rates ranged from 60 K/min to 1 K/min, the microhardness of the HAZ began to decrease due to the presence of ferrite, and the lath sizes grew up to 0.13-0.15 μm. The critical cooling rate to gain fully ferrite was found to be slower than 1 K/min. The welding CCT diagram of CLAM steel was constructed and it showed that there were ferrite and martensite transformation regions only. The diagram made it possible to predict the microstructures and properties of HAZ and became an important tool to evaluate weldability of CLAM steel.

Small-threshold behaviour of two-loop self-energy diagrams: two-particle thresholds

International Nuclear Information System (INIS)

Berends, F.A.; Davydychev, A.I.; Moskovskij Gosudarstvennyj Univ., Moscow; Smirnov, V.A.; Moskovskij Gosudarstvennyj Univ., Moscow

1996-01-01

The behaviour of two-loop two-point diagrams at non-zero thresholds corresponding to two-particle cuts is analyzed. The masses involved in a cut and the external momentum are assumed to be small as compared to some of the other masses of the diagram. By employing general formulae of asymptotic expansions of Feynman diagrams in momenta and masses, we construct an algorithm to derive analytic approximations to the diagrams. In such a way, we calculate several first coefficients of the expansion. Since no conditions on relative values of the small masses and the external momentum are imposed, the threshold irregularities are described analytically. Numerical examples, using diagrams occurring in the standard model, illustrate the convergence of the expansion below the first large threshold. (orig.)

Phase shifts of the paired wings of butterfly diagrams

International Nuclear Information System (INIS)

Li Kejun; Liang Hongfei; Feng Wen

2010-01-01

Sunspot groups observed by the Royal Greenwich Observatory/US Air Force/NOAA from 1874 May to 2008 November and the Carte Synoptique solar filaments from 1919 March to 1989 December are used to investigate the relative phase shift of the paired wings of butterfly diagrams of sunspot and filament activities. Latitudinal migration of sunspot groups (or filaments) does asynchronously occur in the northern and southern hemispheres, and there is a relative phase shift between the paired wings of their butterfly diagrams in a cycle, making the paired wings spatially asymmetrical on the solar equator. It is inferred that hemispherical solar activity strength should evolve in a similar way within the paired wings of a butterfly diagram in a cycle, demonstrating the paired wings phenomenon and showing the phase relationship between the northern and southern hemispherical solar activity strengths, as well as a relative phase shift between the paired wings of a butterfly diagram, which should bring about almost the same relative phase shift of hemispheric solar activity strength. (research papers)

Multiple representations and free-body diagrams: Do students benefit from using them?

Science.gov (United States)

Rosengrant, David R.

2007-12-01

Introductory physics students have difficulties understanding concepts and solving problems. When they solve problems, they use surface features of the problems to find an equation to calculate a numerical answer often not understanding the physics in the problem. How do we help students approach problem solving in an expert manner? A possible answer is to help them learn to represent knowledge in multiple ways and then use these different representations for conceptual understanding and problem solving. This solution follows from research in cognitive science and in physics education. However, there are no studies in physics that investigate whether students who learn to use multiple representations are in fact better problem solvers. This study focuses on one specific representation used in physics--a free body diagram. A free-body diagram is a graphical representation of forces exerted on an object of interest by other objects. I used the free-body diagram to investigate five main questions: (1) If students are in a course where they consistently use free body diagrams to construct and test concepts in mechanics, electricity and magnetism and to solve problems in class and in homework, will they draw free-body diagrams on their own when solving exam problems? (2) Are students who use free-body diagrams to solve problems more successful then those who do not? (3) Why do students draw free-body diagrams when solving problems? (4) Are students consistent in constructing diagrams for different concepts in physics and are they consistent in the quality of their diagrams? (5) What are possible relationships between features of a problem and how likely a student will draw a free body diagram to help them solve the problem? I utilized a mixed-methods approach to answer these questions. Questions 1, 2, 4 and 5 required a quantitative approach while question 3 required a qualitative approach, a case study. When I completed my study, I found that if students are in an

A comparison of two approaches for solving unconstrained influence diagrams

DEFF Research Database (Denmark)

Ahlmann-Ohlsen, Kristian S.; Jensen, Finn V.; Nielsen, Thomas Dyhre

2009-01-01

Influence diagrams and decision trees represent the two most common frameworks for specifying and solving decision problems. As modeling languages, both of these frameworks require that the decision analyst specifies all possible sequences of observations and decisions (in influence diagrams, thi...

Spacelike penguin diagram effects in B implies PP decays

International Nuclear Information System (INIS)

Du, D.; Yang, M.; Zhang, D.

1996-01-01

The spacelike penguin diagram contributions to branching ratios and CP asymmetries in charmless decays of B to two pseudoscalar mesons are studied using the next-to-leading order low energy effective Hamiltonian. Both the gluonic penguin and the electroweak penguin diagrams are considered. We find that the effects are significant. copyright 1995 The American Physical Society

The use of influence diagrams for evaluating severe accident management strategies

International Nuclear Information System (INIS)

Jae, M.; Apostolakis, G.E.

1992-01-01

In this paper, the influence diagram, a new analytical tool for developing and evaluating severe accident management strategies, is presented. Influence diagrams are much simpler than decision trees because they do not lead to the large number of branches that are generated when decision trees are used in realistic problems; furthermore, they show explicitly the dependencies between the variables of the problem. One of the accident management strategies proposed for light water reactors, flooding the reactor cavity as a means of preventing vessel breach during a short-term station blackout sequence, is presented. The influence diagram associated with this strategy is constructed. Finally, the advantages of using influence diagrams in accident management are explored

Merit exponents and control area diagrams in materials selection

International Nuclear Information System (INIS)

Zander, Johan; Sandstroem, Rolf

2011-01-01

Highlights: → Merit exponents are introduced to generalise the merit indices commonly used in materials selection. → The merit exponents can rank materials in general design situations. → To allow identification of the active merit exponent(s), control area diagrams are used. → Principles for generating the control area diagrams are presented. -- Abstract: Merit indices play a fundamental role in materials selection, since they enable ranking of materials. However, the conventional formulation of merit indices is associated with severe limitations. They are dependent on the explicit solution of the variables in the equations for the constraints from the design criteria. Furthermore, it is not always easy to determine which the controlling merit index is. To enable the ranking of materials in more general design cases, merit exponents are introduced as generalisations of the merit indices. Procedures are presented for how to compute the merit exponents numerically without having to solve equations algebraically. Merit exponents (and indices) are only valid in a certain range of property values. To simplify the identification of the controlling merit exponent, it is suggested that so called control area diagrams are used. These diagrams consist of a number of domains, each showing the active constraints and the controlling merit exponent. It is shown that the merit exponents play a crucial role when the control area diagram (CAD) is set up. The principles in the paper are developed for mechanically loaded components and are illustrated for engineering beams with two or three geometric variables.

The importance of design in learning from node-link diagrams

NARCIS (Netherlands)

Amelsvoort, Marije; van der Meij, Jan; Anjewierden, Anjo Allert; van der Meij, Hans

2013-01-01

Diagrams organize by location. They give spatial cues for finding and recognizing information and for making inferences. In education, diagrams are often used to help students understand and recall information. This study assessed the influence of perceptual cues on reading behavior and subsequent

Re-determination of succinonitrile (SCN) camphor phase diagram

Science.gov (United States)

Teng, Jing; Liu, Shan

2006-04-01

Low-melting temperature transparent organic materials have been extensively used to study the pattern formation and microstructure evolution. It proves to be very challenging to accurately determine the phase diagram since there is no viable way to measure the composition microscopically. In this paper, we presented the detailed experimental characterization of the phase diagram of succinonitrile (SCN)-camphor binary system. Differential scanning calorimetry, a ring-heater, and the directional solidification technique have been combined to determine the details of the phase diagram by using the purified materials. The advantages and disadvantages have been discussed for the different experimental techniques. SCN and camphor constitute a simple binary eutectic system with the eutectic composition at 23.6 wt% camphor and eutectic temperature at 37.65 °C. The solidus and the solubility of the SCN base solid solution have been precisely determined for the first time in this binary system.

Designing a supply chain of ready-mix concrete using Voronoi diagrams

Science.gov (United States)

Kozniewski, E.; Orlowski, M.; Orlowski, Z.

2017-10-01

Voronoi diagrams are used to solve scientific and practical problems in many fields. In this paper Voronoi diagrams have been applied to logistic problems in construction, more specifically in the design of the ready-mix concrete supply chain. Apart from the Voronoi diagram, the so-called time-distance circle (circle of range), which in metric space terminology is simply a sphere, appears useful. It was introduced to solve the problem of supplying concrete-related goods.

Phase diagram of a QED-cavity array coupled via a N-type level scheme

Energy Technology Data Exchange (ETDEWEB)

Jin, Jiasen; Rossini, Davide [CNR, NEST, Scuola Normale Superiore and Istituto di Nanoscienze, Pisa (Italy); Fazio, Rosario [CNR, NEST, Scuola Normale Superiore and Istituto di Nanoscienze, Pisa (Italy); National University of Singapore, Center for Quantum Technologies, Singapore (Singapore)

2015-01-01

We study the zero-temperature phase diagram of a one-dimensional array of QED cavities where, besides the single-photon hopping, an additional coupling between neighboring cavities is mediated by an N-type four-level system. By varying the relative strength of the various couplings, the array is shown to exhibit a variety of quantum phases including a polaritonic Mott insulator, a density-wave and a superfluid phase. Our results have been obtained by means of numerical density-matrix renormalization group calculations. The phase diagram was obtained by analyzing the energy gaps for the polaritons, as well as through a study of two-point correlation functions. (orig.)

Leak before break piping evaluation diagram

International Nuclear Information System (INIS)

Fabi, R.J.; Peck, D.A.

1994-01-01

Traditionally Leak Before Break (LBB) has been applied to the evaluation of piping in existing nuclear plants. This paper presents a simple method for evaluating piping systems for LBB during the design process. This method produces a piping evaluation diagram (PED) which defines the LBB requirements to the piping designer for use during the design process. Several sets of LBB analyses are performed for each different pipe size and material considered in the LBB application. The results of this method are independent of the actual pipe routing. Two complete LBB evaluations are performed to determine the maximum allowable stability load, one evaluation for a low normal operating load, and the other evaluation for a high normal operating load. These normal operating loads span the typical loads for the particular system being evaluated. In developing the allowable loads, the appropriate LBB margins are included in the PED preparation. The resulting LBB solutions are plotted as a set of allowable curves for the maximum design basis load, such is the seismic load versus the normal operating load. Since the required margins are already accounted for in the LBB PED, the piping designer can use the diagram directly with the results of the piping analysis and determine immediately if the current piping arrangement passes LBB. Since the LBB PED is independent of pipe routing, changes to the piping system can be evaluated using the existing PED. For a particular application, all that remains is to confirm that the actual materials and pipe sizes assumed in creating the particular design are built into the plant

Algorithmic approach to diagram techniques

International Nuclear Information System (INIS)

Ponticopoulos, L.

1980-10-01

An algorithmic approach to diagram techniques of elementary particles is proposed. The definition and axiomatics of the theory of algorithms are presented, followed by the list of instructions of an algorithm formalizing the construction of graphs and the assignment of mathematical objects to them. (T.A.)

Diagrams in the polaron model

International Nuclear Information System (INIS)

Smondyrev, M.A.

1985-01-01

The perturbation theory for the polaron energy is systematically treated on the diagrammatic basis. Feynman diagrams being constructed allow to calculate the polaron energy up to the third order in powers of the coupling constant. Similar calculations are performed for the average number of virtual phonons

Relation between time-temperature transformation and continuous heating transformation diagrams of metallic glassy alloys

International Nuclear Information System (INIS)

Louzguine-Luzgin, Dmitri V.; Inoue, Akihisa

2005-01-01

The time-temperature transformation (TTT) diagrams for the onset of devitrification of the Ge-Ni-La and Cu-Hf-Ti glassy alloys were calculated from the isothermal differential calorimetry data using an Arrhenius equation. The continuous heating transformation (CHT) diagrams for the onset of devitrification of the glassy alloys were subsequently recalculated from TTT diagrams. The recalculation method used for conversion of the TTT into CHT diagrams produces reasonable results and is not sensitive to the type of the devitrification reaction (polymorphous or primary transformation). The diagrams allow to perform a comparison of the stabilities of glassy alloys on a long-term scale. The relationship between these diagrams is discussed

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips et al and Selby et al has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances, an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g., the top node). In the references cited above, the authors demonstrated the usefulness of influence diagrams for assessing the reliability of operator performance during pressurized thermal shock transients. In addition, the use of influence diagrams identified the critical variables that had the greatest impact on operator reliability for a particular scenario (e.g., control room design, procedures, etc.). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

Application of the cause-consequence diagram method to static systems

International Nuclear Information System (INIS)

Andrews, J.D.; Ridley, L.M.

2002-01-01

In the last 30 years, various mathematical models have been used to identify the effect of component failures on the performance of a system. The most frequently used technique for system reliability assessment is Fault Tree Analysis (FTA) and a large proportion of its popularity can be attributed to the fact that it provides a very good documentation of the way that the system failure logic was developed. Exact quantification of the fault tree, however, can be problematic for very large systems and in such situations, approximations can be used. Alternatively, an exact result can be obtained via the conversion of the fault tree into a binary decision diagram (BDD). The BDD, however, loses all failure logic documentation during the conversion process. This paper outlines the use of the cause-consequence diagram method as a tool for system risk and reliability analysis. As with the FTA method, the cause-consequence diagram documents the failure logic of the system. In addition to this the cause-consequence diagram produces the exact failure probability in a very efficient calculation procedure. The cause-consequence diagram technique has been applied to a static system and shown to yield the same result as those produced by the solution of the equivalent fault tree and BDD. On the basis of this general rules have been devised for the correct construction of the cause-consequence diagram given a static system. The use of the cause-consequence method in this manner has significant implications in terms of efficiency of the reliability analysis and can be shown to have benefits for static systems

Conformational properties of rigid-chain amphiphilic macromolecules : The phase diagram

NARCIS (Netherlands)

Markov, V. A.; Vasilevskaya, V. V.; Khalatur, P. G.; ten Brinke, G.; Khokhlov, A. R.

The coil-globule transition in rigid-chain amphiphilic macromolecules was studied by means of computer simulation, and the phase diagrams for such molecules in the solvent quality-persistence length coordinates were constructed. It was shown that the type of phase diagram depends to a substantial

Phase diagram of the disordered Bose-Hubbard model

International Nuclear Information System (INIS)

Gurarie, V.; Pollet, L.; Prokof'ev, N. V.; Svistunov, B. V.; Troyer, M.

2009-01-01

We establish the phase diagram of the disordered three-dimensional Bose-Hubbard model at unity filling which has been controversial for many years. The theorem of inclusions, proven by Pollet et al. [Phys. Rev. Lett. 103, 140402 (2009)] states that the Bose-glass phase always intervenes between the Mott insulating and superfluid phases. Here, we note that assumptions on which the theorem is based exclude phase transitions between gapped (Mott insulator) and gapless phases (Bose glass). The apparent paradox is resolved through a unique mechanism: such transitions have to be of the Griffiths type when the vanishing of the gap at the critical point is due to a zero concentration of rare regions where extreme fluctuations of disorder mimic a regular gapless system. An exactly solvable random transverse field Ising model in one dimension is used to illustrate the point. A highly nontrivial overall shape of the phase diagram is revealed with the worm algorithm. The phase diagram features a long superfluid finger at strong disorder and on-site interaction. Moreover, bosonic superfluidity is extremely robust against disorder in a broad range of interaction parameters; it persists in random potentials nearly 50 (!) times larger than the particle half-bandwidth. Finally, we comment on the feasibility of obtaining this phase diagram in cold-atom experiments, which work with trapped systems at finite temperature.

The Critical Importance of Russell's Diagram

Science.gov (United States)

Gingerich, O.

2013-04-01

The idea of dwarf and giants stars, but not the nomenclature, was first established by Eijnar Hertzsprung in 1905; his first diagrams in support appeared in 1911. In 1913 Henry Norris Russell could demonstrate the effect far more strikingly because he measured the parallaxes of many stars at Cambridge, and could plot absolute magnitude against spectral type for many points. The general concept of dwarf and giant stars was essential in the galactic structure work of Harlow Shapley, Russell's first graduate student. In order to calibrate the period-luminosity relation of Cepheid variables, he was obliged to fall back on statistical parallax using only 11 Cepheids, a very sparse sample. Here the insight provided by the Russell diagram became critical. The presence of yellow K giant stars in globular clusters credentialed his calibration of the period-luminosity relation by showing that the calibrated luminosity of the Cepheids was comparable to the luminosity of the K giants. It is well known that in 1920 Shapley did not believe in the cosmological distances of Heber Curtis' spiral nebulae. It is not so well known that in 1920 Curtis' plot of the period-luminosity relation suggests that he didn't believe it was a physical relation and also he failed to appreciate the significance of the Russell diagram for understanding the large size of the Milky Way.

Warped penguin diagrams

International Nuclear Information System (INIS)

Csaki, Csaba; Grossman, Yuval; Tanedo, Philip; Tsai, Yuhsin

2011-01-01

We present an analysis of the loop-induced magnetic dipole operator in the Randall-Sundrum model of a warped extra dimension with anarchic bulk fermions and an IR brane-localized Higgs. These operators are finite at one-loop order and we explicitly calculate the branching ratio for μ→eγ using the mixed position/momentum space formalism. The particular bound on the anarchic Yukawa and Kaluza-Klein (KK) scales can depend on the flavor structure of the anarchic matrices. It is possible for a generic model to either be ruled out or unaffected by these bounds without any fine-tuning. We quantify how these models realize this surprising behavior. We also review tree-level lepton flavor bounds in these models and show that these are on the verge of tension with the μ→eγ bounds from typical models with a 3 TeV Kaluza-Klein scale. Further, we illuminate the nature of the one-loop finiteness of these diagrams and show how to accurately determine the degree of divergence of a five-dimensional loop diagram using both the five-dimensional and KK formalism. This power counting can be obfuscated in the four-dimensional Kaluza-Klein formalism and we explicitly point out subtleties that ensure that the two formalisms agree. Finally, we remark on the existence of a perturbative regime in which these one-loop results give the dominant contribution.

Three-body crystallization diagrams and the cooling of white dwarfs.

Science.gov (United States)

Segretain, L.

1996-06-01

The 3-body crystallization diagrams of C/O/Ne ionic mixtures characteristic of white dwarf interiors are examined within the framework of the density-functional theory of freezing. The crystallization process is described more accurately than in former calculations where the three-component system was treated as an effective two-component mixture (Segretain et al. 1994). The distillation process due to neon-crystallization is found to occur only for the late stages of crystallization. At the beginning, the presence of neon plays only a minor role and the phase diagram resembles a pure carbon-oxygen diagram. The final phase diagram is found to exhibit an azeotropic point with a neon concentration x_Ne_=0.22, a carbon concentration x_C_=0.78 and an oxygen concentration x_O_=0, so that during the distillation process, the fluid crystallizes into a pure neon-carbon solid. The critical temperature is T_A_=0.85T_C_, where T_C_ is the pure carbon crystallization temperature. We use this accurate phase diagram to calculate the total gravitational energy released during white dwarf crystallization and the related time delay. The final result yields {DELTA}τ=~2.6Gyr, among which about 20% are due to the neon-distillation process.

Identification of high school students' ability level of constructing free body diagrams to solve restricted and structured response items in force matter

Science.gov (United States)

Rahmaniar, Andinisa; Rusnayati, Heni; Sutiadi, Asep

2017-05-01

While solving physics problem particularly in force matter, it is needed to have the ability of constructing free body diagrams which can help students to analyse every force which acts on an object, the length of its vector and the naming of its force. Mix method was used to explain the result without any special treatment to participants. The participants were high school students in first grade totals 35 students. The purpose of this study is to identify students' ability level of constructing free body diagrams in solving restricted and structured response items. Considering of two types of test, every student would be classified into four levels ability of constructing free body diagrams which is every level has different characteristic and some students were interviewed while solving test in order to know how students solve the problem. The result showed students' ability of constructing free body diagrams on restricted response items about 34.86% included in no evidence of level, 24.11% inadequate level, 29.14% needs improvement level and 4.0% adequate level. On structured response items is about 16.59% included no evidence of level, 23.99% inadequate level, 36% needs improvement level, and 13.71% adequate level. Researcher found that students who constructed free body diagrams first and constructed free body diagrams correctly were more successful in solving restricted and structured response items.

Quarks and gluons in the phase diagram of quantum chromodynamics

Energy Technology Data Exchange (ETDEWEB)

Welzbacher, Christian Andreas

2016-07-14

In this dissertation we study the phase diagram of strongly interacting matter by approaching the theory of quantum chromodynamics in the functional approach of Dyson-Schwinger equations. With these quantum (field) equations of motions we calculate the non-perturbative quark propagator within the Matsubara formalism. We built up on previous works and extend the so-called truncation scheme, which is necessary to render the infinite tower of Dyson-Schwinger equations finite and study phase transitions of chiral symmetry and the confinement/deconfinement transition. In the first part of this thesis we discuss general aspects of quantum chromodynamics and introduce the Dyson-Schwinger equations in general and present the quark Dyson-Schwinger equation together with its counterpart for the gluon. The Bethe-Salpeter equation is introduced which is necessary to perform two-body bound state calculations. A view on the phase diagram of quantum chromodynamics is given, including the discussion of order parameter for chiral symmetry and confinement. Here we also discuss the dependence of the phase structure on the masses of the quarks. In the following we present the truncation and our results for an unquenched N{sub f} = 2+1 calculation and compare it to previous studies. We highlight some complementary details for the quark and gluon propagator and discus the resulting phase diagram, which is in agreement with previous work. Results for an equivalent of the Columbia plot and the critical surface are discussed. A systematically improved truncation, where the charm quark as a dynamical quark flavour is added, will be presented in Ch. 4. An important aspect in this investigation is the proper adjustment of the scales. This is done by matching vacuum properties of the relevant pseudoscalar mesons separately for N{sub f} = 2+1 and N f = 2+1+1 via a solution of the Bethe-Salpeter equation. A comparison of the resulting N{sub f} = 2+1 and N{sub f} = 2+1+1 phase diagram indicates

Y-12 Plant Remedial Action technology logic diagram. Volume I: Technology evaluation

International Nuclear Information System (INIS)

1994-09-01

The Y-12 Plant Remedial Action Program addresses remediation of the contaminated groundwater, surface water and soil in the following areas located on the Oak Ridge Reservation: Chestnut Ridge, Bear Creek Valley, the Upper and Lower East Fork Popular Creek Watersheds, CAPCA 1, which includes several areas in which remediation has been completed, and CAPCA 2, which includes dense nonaqueous phase liquid wells and a storage facility. There are many facilities within these areas that are contaminated by uranium, mercury, organics, and other materials. This Technology Logic Diagram identifies possible remediation technologies that can be applied to the soil, water, and contaminants for characterization, treatment, and waste management technology options are supplemented by identification of possible robotics or automation technologies. These would facilitate the cleanup effort by improving safety, of remediation, improving the final remediation product, or decreasing the remediation cost. The Technology Logic Diagram was prepared by a diverse group of more than 35 scientists and engineers from across the Oak Ridge Reservation. Most are specialists in the areas of their contributions. 22 refs., 25 tabs

The colour-magnitude diagram of NGC 5053

International Nuclear Information System (INIS)

Walker, M.F.; Pike, C.D.; McGee, J.D.

1976-01-01

The colour-magnitude diagram of NGC 5053 has been derived to V = 21.1 from photographic and electronographic observations. The electronographic observations were obtained with an experimental Spectracon image-converter, having photocathode and exit window dimensions of 20 x 30 mm, mounted at the prime-focus of the 120-in. Lick reflector. The photographic observations were obtained with the 20-in. Carnegie astrograph and the 36-in. Crossley reflector. The colour-magnitude diagram resembles that of M92, with the difference that a red horizontal branch is more pronounced than the asymptotic branch in NGC 5053. The topology of the horizontal branch is that of clusters with an intermediate metal content and is thus at variance with the mean period of the RR Lyr stars and the unreddened colour of the subgiant branch read at the magnitude level of the horizontal branch, both of which would indicate an extremely low metal content. If comparison of the colour-magnitude diagrams of NGC 5053 and M92 is valid, then the reddening of NGC 5053 is Esub(B-V) = 0.02 and the apparent distance modulus is m-M = 16.08 +- 0.08. (author)

Fuel conditioning facility zone-to-zone transfer administrative controls

International Nuclear Information System (INIS)

Pope, C. L.

2000-01-01

The administrative controls associated with transferring containers from one criticality hazard control zone to another in the Argonne National Laboratory (ANL) Fuel Conditioning Facility (FCF) are described. FCF, located at the ANL-West site near Idaho Falls, Idaho, is used to remotely process spent sodium bonded metallic fuel for disposition. The process involves nearly forty widely varying material forms and types, over fifty specific use container types, and over thirty distinct zones where work activities occur. During 1999, over five thousand transfers from one zone to another were conducted. Limits are placed on mass, material form and type, and container types for each zone. Ml material and containers are tracked using the Mass Tracking System (MTG). The MTG uses an Oracle database and numerous applications to manage the database. The database stores information specific to the process, including material composition and mass, container identification number and mass, transfer history, and the operators involved in each transfer. The process is controlled using written procedures which specify the zone, containers, and material involved in a task. Transferring a container from one zone to another is called a zone-to-zone transfer (ZZT). ZZTs consist of four distinct phases, select, request, identify, and completion

Phase Diagrams of Electrostatically Self-Assembled Amphiplexes

Energy Technology Data Exchange (ETDEWEB)

V Stanic; M Mancuso; W Wong; E DiMasi; H Strey

2011-12-31

We present the phase diagrams of electrostatically self-assembled amphiplexes (ESA) comprised of poly(acrylic acid) (PAA), cetyltrimethylammonium chloride (CTACl), dodecane, pentanol, and water at three different NaCl salt concentrations: 100, 300, and 500 mM. This is the first report of phase diagrams for these quinary complexes. Adding a cosurfactant, we were able to swell the unit cell size of all long-range ordered phases (lamellar, hexagonal, Pm3n, Ia3d) by almost a factor of 2. The added advantage of tuning the unit cell size makes such complexes (especially the bicontinuous phases) attractive for applications in bioseparation, drug delivery, and possibly in oil recovery.

COMBINED EFFECTS OF BINARIES AND STELLAR ROTATION ON THE COLOR-MAGNITUDE DIAGRAMS OF INTERMEDIATE-AGE STAR CLUSTERS

International Nuclear Information System (INIS)

Li Zhongmu; Mao Caiyan; Chen Li; Zhang Qian

2012-01-01

About 70% of intermediate-age star clusters in the Large Magellanic Clouds have been confirmed to have broad main sequence, multiple or extended turnoffs, and dual red giant clumps. The observed result seems to be at odds with the classical idea that such clusters are simple stellar populations. Although many models have been used to explain the results via factors such as prolonged star formation history, metallicity spread, differential reddening, selection effect, observational uncertainty, stellar rotation, and binary interaction, the reason for the special color-magnitude diagrams is still uncertain. We revisit this question via the combination of stellar rotation and binary effects. As a result, it shows 'golf club' color-magnitude diagrams with broad or multiple turnoffs, dual red clumps, blue stragglers, red stragglers, and extended main sequences. Because both binaries and massive rotators are common, our result suggests that most color-magnitude diagrams, including extended turnoff or multiple turnoffs, can be explained using simple stellar populations including both binary and stellar rotation effects, or composite populations with two components.

VennDIS: a JavaFX-based Venn and Euler diagram software to generate publication quality figures.

Science.gov (United States)

Ignatchenko, Vladimir; Ignatchenko, Alexandr; Sinha, Ankit; Boutros, Paul C; Kislinger, Thomas

2015-04-01

Venn diagrams are graphical representations of the relationships among multiple sets of objects and are often used to illustrate similarities and differences among genomic and proteomic datasets. All currently existing tools for producing Venn diagrams evince one of two traits; they require expertise in specific statistical software packages (such as R), or lack the flexibility required to produce publication-quality figures. We describe a simple tool that addresses both shortcomings, Venn Diagram Interactive Software (VennDIS), a JavaFX-based solution for producing highly customizable, publication-quality Venn, and Euler diagrams of up to five sets. The strengths of VennDIS are its simple graphical user interface and its large array of customization options, including the ability to modify attributes such as font, style and position of the labels, background color, size of the circle/ellipse, and outline color. It is platform independent and provides real-time visualization of figure modifications. The created figures can be saved as XML files for future modification or exported as high-resolution images for direct use in publications. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Project Management Plan for the INEL technology logic diagrams

International Nuclear Information System (INIS)

Rudin, M.J.

1992-10-01

This Project Management Plan (PjMP) describes the elements of project planning and control that apply to activities outlined in Technical Task Plan (TTP) ID-121117, ''Technology Logic Diagrams For The INEL.'' The work on this project will be conducted by personnel in EG ampersand G Idaho, Inc.'s Waste Technology Development Program. Technology logic diagrams represent a formal methodology to identify technology gaps or needs within Environmental Restoration/Waste Management Operations, which will focus on Office of Environmental Restoration and Waste Management (EM-50) research and development, demonstration, test, and evaluation efforts throughout the US Department of Energy complex. This PjMP describes the objectives, organization, roles and responsibilities, workscope and processes for implementing and managing the technology logic diagram for the Idaho National Engineering Laboratory project

Decorated-box-diagram contributions to Bhabha scattering. Pt. 1

International Nuclear Information System (INIS)

Faeldt, G.; Osland, P.

1994-01-01

We evaluate, in the light-energy limit, s>>vertical stroke tvertical stroke >>m 2 >>λ 2 , the sum of amplitudes corresponding to a class of Feynman diagrams describing two-loop virtual photonic corrections to Bhabha scattering. The diagrams considered are box and crossed-box diagrams with an extra photon decorating one of the fermion lines. The mathematical method employed is that of Mellin transforms. In the eikonal approximation, this sum of two-loop amplitudes has previously been evaluated, and found to be equal to the sum of the box and crossed-box amplitudes, multiplied by the electric form factor of the electron. We obtain a similar factorization, but with the form factor replaced by another expression involving the logarithms log(λ 2 /m 2 ) and log(λ 2 /vertical stroke tvertical stroke ). (orig.)

Characterizing the Magnetic Properties of Natural Samples Using First-Order Reversal Curve Diagrams

Science.gov (United States)

Pike, C. R.; Roberts, A. P.; Verosub, K. L.

2001-12-01

domain wall (DW) pinning. It is not known what physical mechanism is responsible for the breakdown of the classical DW pinning model, but possibilities include DW interactions, DW nucleation and annihilation, and DW curvature. FORC diagrams should prove to be useful in testing alternative models in future rock magnetic investigations.

Nonplanar on-shell diagrams and leading singularities of scattering amplitudes

Energy Technology Data Exchange (ETDEWEB)

Chen, Baoyi; Cheung, Yeuk-Kwan E.; Li, Yunxuan; Xie, Ruofei; Xin, Yuan [Nanjing University, Department of Physics, Nanjing (China); Chen, Gang [Zhejiang Normal University, Department of Physics, Jinhua, Zhejiang (China); Nanjing University, Department of Physics, Nanjing (China)

2017-02-15

Bipartite on-shell diagrams are the latest tool in constructing scattering amplitudes. In this paper we prove that a Britto-Cachazo-Feng-Witten (BCFW) decomposable on-shell diagram process a rational top form if and only if the algebraic ideal comprised the geometrical constraints are shifted linearly during successive BCFW integrations. With a proper geometric interpretation of the constraints in the Grassmannian manifold, the rational top form integration contours can thus be obtained, and understood, in a straightforward way. All rational top form integrands of arbitrary higher loops leading singularities can therefore be derived recursively, as long as the corresponding on-shell diagram is BCFW decomposable. (orig.)

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips and Selby has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top node). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

Drawing and Using Free Body Diagrams: Why It May Be Better Not to Decompose Forces

Science.gov (United States)

Aviani, Ivica; Erceg, Nataša; Mešic, Vanes

2015-01-01

In this study we investigated how two different approaches to drawing free body diagrams influence the development of students' understanding of Newton's laws, including their ability to identify real forces. For this purpose we developed a 12-item two-tier multiple choice survey and conducted a quasiexperiment. This experiment included two groups…

Quantitative study of FORC diagrams in thermally corrected Stoner– Wohlfarth nanoparticles systems

International Nuclear Information System (INIS)

De Biasi, E.; Curiale, J.; Zysler, R.D.

2016-01-01

The use of FORC diagrams is becoming increasingly popular among researchers devoted to magnetism and magnetic materials. However, a thorough interpretation of this kind of diagrams, in order to achieve quantitative information, requires an appropriate model of the studied system. For that reason most of the FORC studies are used for a qualitative analysis. In magnetic systems thermal fluctuations 'blur' the signatures of the anisotropy, volume and particle interactions distributions, therefore thermal effects in nanoparticles systems conspire against a proper interpretation and analysis of these diagrams. Motivated by this fact, we have quantitatively studied the degree of accuracy of the information extracted from FORC diagrams for the special case of single-domain thermal corrected Stoner– Wohlfarth (easy axes along the external field orientation) nanoparticles systems. In this work, the starting point is an analytical model that describes the behavior of a magnetic nanoparticles system as a function of field, anisotropy, temperature and measurement time. In order to study the quantitative degree of accuracy of our model, we built FORC diagrams for different archetypical cases of magnetic nanoparticles. Our results show that from the quantitative information obtained from the diagrams, under the hypotheses of the proposed model, is possible to recover the features of the original system with accuracy above 95%. This accuracy is improved at low temperatures and also it is possible to access to the anisotropy distribution directly from the FORC coercive field profile. Indeed, our simulations predict that the volume distribution plays a secondary role being the mean value and its deviation the only important parameters. Therefore it is possible to obtain an accurate result for the inversion and interaction fields despite the features of the volume distribution. - Highlights: • Quantify the degree of accuracy of the information obtained using the FORC diagrams. �

The Reed & Kellogg System of Sentence Diagramming and Its Implementation in Higher Education

Science.gov (United States)

Coats, Judith Ruth

2012-01-01

The purpose of this study was to research whether or not the intervention of the Reed & Kellogg System of sentence diagramming would make a significant difference in the acquisition, retention, and comprehension of the basic grammatical skills, including parts of speech, complements, phrases, clauses, and sentence structures, on the higher…

The annihilation diagram in three-body D-meson decay

International Nuclear Information System (INIS)

Donoghue, J.F.; Holstein, B.R.

1981-01-01

We discuss some features of three-body decays of the D meson cohich are puzzling from the standpoint of the annihilation diagram. As a result, we (1) provide an upper bound on the lifetime ratio of D's, tau + sub(D)/tau 0 sub(D) smaller than 2.5 +- 3.4 and (2) argue that the puzzles are resolved, even if somewhat inelegantly, if final state interactions generate the annihilation diagram. (orig.)

Phase diagram for the Kuramoto model with van Hemmen interactions.

Science.gov (United States)

Kloumann, Isabel M; Lizarraga, Ian M; Strogatz, Steven H

2014-01-01

We consider a Kuramoto model of coupled oscillators that includes quenched random interactions of the type used by van Hemmen in his model of spin glasses. The phase diagram is obtained analytically for the case of zero noise and a Lorentzian distribution of the oscillators' natural frequencies. Depending on the size of the attractive and random coupling terms, the system displays four states: complete incoherence, partial synchronization, partial antiphase synchronization, and a mix of antiphase and ordinary synchronization.

Exploring the QCD phase diagram through relativistic heavy ion collisions

Directory of Open Access Journals (Sweden)

Mohanty Bedangadas

2014-03-01

Full Text Available We present a review of the studies related to establishing the QCD phase diagram through high energy nucleus-nucleus collisions. We particularly focus on the experimental results related to the formation of a quark-gluon phase, crossover transition and search for a critical point in the QCD phase diagram.

Heuristic Diagrams as a Tool to Teach History of Science

Science.gov (United States)

Chamizo, Jose A.

2012-01-01

The graphic organizer called here heuristic diagram as an improvement of Gowin's Vee heuristic is proposed as a tool to teach history of science. Heuristic diagrams have the purpose of helping students (or teachers, or researchers) to understand their own research considering that asks and problem-solving are central to scientific activity. The…

Initial Hubble Diagram Results from the Nearby Supernova Factory

Energy Technology Data Exchange (ETDEWEB)

Bailey, S. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France); Aldering, G. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Antilogus, P. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France); Aragon, C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Baltay, C. [Yale Univ., New Haven, CT (United States); Bongard, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Buton, C [Inst. of Nuclear Physics of Lyon (France); Childress, M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Copin, Y. [Inst. of Nuclear Physics of Lyon (France); Gangler, E. [Inst. of Nuclear Physics of Lyon (France); Loken, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Nugent, P. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Pain, R. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France); Pecontal, E. [Center of Research Astrophysics of Lyon (CRAL) (France); Pereira, R. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France); Perlmutter, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rabinowitz, D. [Yale Univ., New Haven, CT (United States); Rigaudier, G. [Center of Research Astrophysics of Lyon (CRAL) (France); Ripoche, P. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France); Runge, K. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Scalzo, R. [Yale Univ., New Haven, CT (United States); Smadja, G. [Inst. of Nuclear Physics of Lyon (France); Tao, C. [Inst. of Nuclear Physics of Lyon (France); Thomas, R. C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wu, C. [Lab. Nuclear and High-Energy Physics (LPNHE), Paris (France)

2017-07-06

The use of Type Ia supernovae as distance indicators led to the discovery of the accelerating expansion of the universe a decade ago. Now that large second generation surveys have significantly increased the size and quality of the high-redshift sample, the cosmological constraints are limited by the currently available sample of ~50 cosmologically useful nearby supernovae. The Nearby Supernova Factory addresses this problem by discovering nearby supernovae and observing their spectrophotometric time development. Our data sample includes over 2400 spectra from spectral timeseries of 185 supernovae. This talk presents results from a portion of this sample including a Hubble diagram (relative distance vs. redshift) and a description of some analyses using this rich dataset.

Effect of Thermal Distress on Residual Behavior of CFRP-Strengthened Steel Beams Including Periodic Unbonded Zones

Directory of Open Access Journals (Sweden)

Isamu Yoshitake

2015-11-01

Full Text Available This paper presents the residual behavior of wide-flange steel beams strengthened with high-modulus carbon fiber-reinforced polymer (CFRP laminates subjected to thermal loading. Because the coefficients of thermal expansion of the steel and the CFRP are different, temperature-induced distress may take place along their interface. Periodic unbonded zones are considered to represent local interfacial damage. Five test categories are designed depending on the size of the unbonded zones from 10 to 50 mm, and corresponding beams are loaded until failure occurs after exposing to a cyclic temperature range of ΔT = 25 °C (−10 to 15 °C up to 84 days. The composite action between the CFRP and the steel substrate is preserved until yielding of the beams happens, regardless of the thermal cycling and periodic unbonded zones. The initiation and progression of CFRP debonding become apparent as the beams are further loaded, particularly at geometric discontinuities in the vicinity of the unbonded zones along the interface. A simple analytical model is employed to predict the interfacial stress of the strengthened beams. A threshold temperature difference of ΔT = 30 °C is estimated for the initiation and progression of CFRP debonding. Multiple debonding-progression stages in conjunction with the extent of thermal distress appear to exist. It is recommended that high-modulus CFRP be restrictively used for strengthening steel members potentially exposed to a wide temperature variation range.

Students’ understanding of forces: Force diagrams on horizontal and inclined plane

Science.gov (United States)

Sirait, J.; Hamdani; Mursyid, S.

2018-03-01

This study aims to analyse students’ difficulties in understanding force diagrams on horizontal surfaces and inclined planes. Physics education students (pre-service physics teachers) of Tanjungpura University, who had completed a Basic Physics course, took a Force concept test which has six questions covering three concepts: an object at rest, an object moving at constant speed, and an object moving at constant acceleration both on a horizontal surface and on an inclined plane. The test is in a multiple-choice format. It examines the ability of students to select appropriate force diagrams depending on the context. The results show that 44% of students have difficulties in solving the test (these students only could solve one or two items out of six items). About 50% of students faced difficulties finding the correct diagram of an object when it has constant speed and acceleration in both contexts. In general, students could only correctly identify 48% of the force diagrams on the test. The most difficult task for the students in terms was identifying the force diagram representing forces exerted on an object on in an inclined plane.

Diagrams: A Visual Survey of Graphs, Maps, Charts and Diagrams for the Graphic Designer.

Science.gov (United States)

Lockwood, Arthur

Since the ultimate success of any diagram rests in its clarity, it is important that the designer select a method of presentation which will achieve this aim. He should be aware of the various ways in which statistics can be shown diagrammatically, how information can be incorporated in maps, and how events can be plotted in chart or graph form.…

Interactive Cost Configuration Over Decision Diagrams

DEFF Research Database (Denmark)

Andersen, Henrik Reif; Hadzic, Tarik; Pisinger, David

2010-01-01

interaction online. In particular,binary decision diagrams (BDDs) have been successfully used as a compilation target for product and service configuration. In this paper we discuss how to extend BDD-based configuration to scenarios involving cost functions which express user preferences. We first show...... that an efficient, robust and easy to implement extension is possible if the cost function is additive, and feasible solutions are represented using multi-valued decision diagrams (MDDs). We also discuss the effect on MDD size if the cost function is non-additive or if it is encoded explicitly into MDD. We...... then discuss interactive configuration in the presence of multiple cost functions. We prove that even in its simplest form, multiple-cost configuration is NP-hard in the input MDD. However, for solving two-cost configuration we develop a pseudo-polynomial scheme and a fully polynomial approximation scheme...

Technological Literacy Learning with Cumulative and Stepwise Integration of Equations into Electrical Circuit Diagrams

Science.gov (United States)

Ozogul, G.; Johnson, A. M.; Moreno, R.; Reisslein, M.

2012-01-01

Technological literacy education involves the teaching of basic engineering principles and problem solving, including elementary electrical circuit analysis, to non-engineering students. Learning materials on circuit analysis typically rely on equations and schematic diagrams, which are often unfamiliar to non-engineering students. The goal of…

TEP process flow diagram

Energy Technology Data Exchange (ETDEWEB)

Wilms, R Scott [Los Alamos National Laboratory; Carlson, Bryan [Los Alamos National Laboratory; Coons, James [Los Alamos National Laboratory; Kubic, William [Los Alamos National Laboratory

2008-01-01

This presentation describes the development of the proposed Process Flow Diagram (PFD) for the Tokamak Exhaust Processing System (TEP) of ITER. A brief review of design efforts leading up to the PFD is followed by a description of the hydrogen-like, air-like, and waterlike processes. Two new design values are described; the mostcommon and most-demanding design values. The proposed PFD is shown to meet specifications under the most-common and mostdemanding design values.

Matrix model approximations of fuzzy scalar field theories and their phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Tekel, Juraj [Department of Theoretical Physics, Faculty of Mathematics, Physics and Informatics, Comenius University, Mlynska Dolina, Bratislava, 842 48 (Slovakia)

2015-12-29

We present an analysis of two different approximations to the scalar field theory on the fuzzy sphere, a nonperturbative and a perturbative one, which are both multitrace matrix models. We show that the former reproduces a phase diagram with correct features in a qualitative agreement with the previous numerical studies and that the latter gives a phase diagram with features not expected in the phase diagram of the field theory.

Investigation on water quality of zabol chahnimeh reservoirs from drinking water and agricultural viewpoint with focus on schuler & vilcoks diagrams

International Nuclear Information System (INIS)

Homayoonnezhad, I.; Amirian, P.; Piri, I.

2016-01-01

Because of the water deficiency, people's requirements and high costs of refining especially in urban zones, water resources management is very essential. Zabol Chahnimeh reservoirs are three natural and big cavities in the south of Sistan Plain Located in South-Eastern Iran and It Includes 50 Millions square meter extent. Stored Water In These Cavities Are Used To Sistan Earth And For Providing Drink Water of Zabol And Zahedan Cities. Because of the drink and agricultural usage and for investigation of water quality of chah-nimeh reservoirs, this research has been done in one year. Methods: In this research density of Na"+ ,Mg"2"+, Ca"2"+ ,Cl"-, SO_4"2"- and EC, TDS,TH parameters have been analyzed in 9 stations, then results have been rebounded on schuler & vilcoks diagrams. Results: Results showed the quality of water in reservoirs viewpoint of drinking sited in acceptable stage and viewpoint of agricultural sited in C_3S_1 (average quality) stage. Discussion & conclusion: finally, if the texture of soil be light, we can use water of these reservoirs for agricultural activities.

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1984-01-01

Recent work by Phillips et al., and Selby et al., has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. An influence diagram is a graphical representation of probabilistic dependence within a system or event sequence. Bayesian statistics are employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top event). As with fault trees, top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. Purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies. In addition, the computing efficiency of both methods is discussed

Phase diagram of structure of radial electric field in helical plasmas

International Nuclear Information System (INIS)

Toda, S.; Itoh, K.

2002-01-01

A set of transport equations in toroidal helical plasmas is analyzed, including the bifurcation of the radial electric field. Multiple solutions of E r for the ambipolar condition induces domains of different electric polarities. A structure of the domain interface is analyzed and a phase diagram is obtained in the space of the external control parameters. The region of the reduction of the anomalous transport is identified. (author)

Profile of High School Students’ Propositional Network Representation when Interpreting Convention Diagrams

Science.gov (United States)

Fatiha, M.; Rahmat, A.; Solihat, R.

2017-09-01

The delivery of concepts in studying Biology often represented through a diagram to easily makes student understand about Biology material. One way to knowing the students’ understanding about diagram can be seen from causal relationship that is constructed by student in the propositional network representation form. This research reveal the trend of students’ propositional network representation patterns when confronted with convention diagram. This descriptive research involved 32 students at one of senior high school in Bandung. The research data was acquired by worksheet that was filled by diagram and it was developed according on information processing standards. The result of this research revealed three propositional network representation patterns are linear relationship, simple reciprocal relationship, and complex reciprocal relationship. The dominating pattern is linear form that is simply connect some information components in diagram by 59,4% students, the reciprocal relationship form with medium level by 28,1% students while the complex reciprocal relationship by only 3,1% and the rest was students who failed to connect information components by 9,4%. Based on results, most of student only able to connect information components on the picture in linear form and a few student constructing reciprocal relationship between information components on convention diagram.

Diagrams of ion stability in radio-frequency mass spectrometry

International Nuclear Information System (INIS)

Sudakov, M.Yu.

1994-01-01

For solving radio-frequency mass spectrometry problems and dynamic ion containment are studied and systematized different ways for constructing the ion stability diagrams. A new universal set of parameters is proposed for diagram construction-angular variables, which are the phase raid of ion oscillational motion during positive and negative values of the supplying voltage. An effective analytical method is proposed for optimization of the parameters of the pulsed supplying voltage, in particular its repetition rate

Large momentum expansion of two-loop self-energy diagrams with arbitrary masses

International Nuclear Information System (INIS)

Davydychev, A.I.; Smirnov, V.A.; Tausk, J.B.

1993-01-01

For two-loop two-point diagrams with arbitrary masses, an algorithm to derive the asymptotic expansion at large external momentum squared is constructed. By using a general theorem on asymptotic expansions of Feynman diagrams, the coefficients of the expansion are calculated analytically. For some two-loop diagrams occurring in the Standard Model, comparison with results of numerical integration shows that our expansion works well in the region above the highest physical threshold. (orig.)

Planetary populations in the mass-period diagram: A statistical treatment of exoplanet formation and the role of planet traps

International Nuclear Information System (INIS)

Hasegawa, Yasuhiro; Pudritz, Ralph E.

2013-01-01

The rapid growth of observed exoplanets has revealed the existence of several distinct planetary populations in the mass-period diagram. Two of the most surprising are (1) the concentration of gas giants around 1 AU and (2) the accumulation of a large number of low-mass planets with tight orbits, also known as super-Earths and hot Neptunes. We have recently shown that protoplanetary disks have multiple planet traps that are characterized by orbital radii in the disks and halt rapid type I planetary migration. By coupling planet traps with the standard core accretion scenario, we showed that one can account for the positions of planets in the mass-period diagram. In this paper, we demonstrate quantitatively that most gas giants formed at planet traps tend to end up around 1 AU, with most of these being contributed by dead zones and ice lines. We also show that a large fraction of super-Earths and hot Neptunes are formed as 'failed' cores of gas giants—this population being constituted by comparable contributions from dead zone and heat transition traps. Our results are based on the evolution of forming planets in an ensemble of disks where we vary only the lifetimes of disks and their mass accretion rates onto the host star. We show that a statistical treatment of the evolution of a large population of planetary cores caught in planet traps accounts for the existence of three distinct exoplanetary populations—the hot Jupiters, the more massive planets around r = 1 AU, and the short-period super-Earths and hot Neptunes. There are very few populations that feed into the large orbital radii characteristic of the imaged Jovian planet, which agrees with recent surveys. Finally, we find that low-mass planets in tight orbits become the dominant planetary population for low-mass stars (M * ≤ 0.7 M ☉ ).

Combining Decision Diagrams and SAT Procedures for Efficient Symbolic Model Checking

DEFF Research Database (Denmark)

Williams, Poul Frederick; Biere, Armin; Clarke, Edmund M.

2000-01-01

In this paper we show how to do symbolic model checking using Boolean Expression Diagrams (BEDs), a non-canonical representation for Boolean formulas, instead of Binary Decision Diagrams (BDDs), the traditionally used canonical representation. The method is based on standard fixed point algorithm...

Using a Density-Management Diagram to Develop Thinning Schedules for Loblolly Pine Plantations

Science.gov (United States)

Thomas J. Dean; V. Clark Baldwin

1993-01-01

A method for developing thinning schedules using a density-management diagram is presented. A density-management diagram is a form of stocking chart based on patterns of natural stand development. The diagram allows rotation diameter and the upper and lower limits of growing stock to be easily transformed into before and after thinning densities. Site height lines on...

Magnetic phase diagram of a nanocone

International Nuclear Information System (INIS)

Suarez, O; Vargas, P; Escrig, J; Landeros, P; Albir, D; Laroze, D

2008-01-01

In this work we analyze the magnetic properties of truncated conical nanoparticles. Based on the continuous magnetic model we find expressions for the total energy in three different magnetic configurations. Finally, we calculate the magnetic phase diagram as function of the geometrical parameters.

Magnetic phase diagram of a nanocone

Energy Technology Data Exchange (ETDEWEB)

Suarez, O; Vargas, P [Departamento de Fisica, Universidad Tecnica Federico Santa MarIa, P. O. Box 110-V, Valparaiso (Chile); Escrig, J; Landeros, P; Albir, D [Universidad de Santiago de Chile, Depatamento de Fisica, Casilla 307, Correo 2, Santiago (Chile); Laroze, D [Instituto de Fisica, Pontificia Universidad Catolica de Valparaiso, P. O. Box 4059, Valparaiso (Chile)], E-mail: omar.suarez@postgrado.usm.cl

2008-11-01

In this work we analyze the magnetic properties of truncated conical nanoparticles. Based on the continuous magnetic model we find expressions for the total energy in three different magnetic configurations. Finally, we calculate the magnetic phase diagram as function of the geometrical parameters.

Thermodynamic properties of alloys and fusibility diagram of Fe-Ni-Mn system

International Nuclear Information System (INIS)

Danilenko, V.M.; Turkevich, V.Z.

1987-01-01

Thermodynamic calculation of the fusibility diagram of Fe-Ni-Mn system in the subregular solution approximation is performed. The calculated fusibility diagram fits the experimental one in kind and degree

Phase diagram for interacting Bose gases

International Nuclear Information System (INIS)

Morawetz, K.; Maennel, M.; Schreiber, M.

2007-01-01

We propose a modified form of the inversion method in terms of a self-energy expansion to access the phase diagram of the Bose-Einstein transition. The dependence of the critical temperature on the interaction parameter is calculated. This is discussed with the help of a condition for Bose-Einstein condensation in interacting systems which follows from the pole of the T matrix in the same way as from the divergence of the medium-dependent scattering length. A many-body approximation consisting of screened ladder diagrams is proposed, which describes the Monte Carlo data more appropriately. The specific results are that a non-self-consistent T matrix leads to a linear coefficient in leading order of 4.7, the screened ladder approximation to 2.3, and the self-consistent T matrix due to the effective mass to a coefficient of 1.3 close to the Monte Carlo data

Geometry Helps to Compare Persistence Diagrams

Energy Technology Data Exchange (ETDEWEB)

Kerber, Michael; Morozov, Dmitriy; Nigmetov, Arnur

2015-11-16

Exploiting geometric structure to improve the asymptotic complexity of discrete assignment problems is a well-studied subject. In contrast, the practical advantages of using geometry for such problems have not been explored. We implement geometric variants of the Hopcroft--Karp algorithm for bottleneck matching (based on previous work by Efrat el al.), and of the auction algorithm by Bertsekas for Wasserstein distance computation. Both implementations use k-d trees to replace a linear scan with a geometric proximity query. Our interest in this problem stems from the desire to compute distances between persistence diagrams, a problem that comes up frequently in topological data analysis. We show that our geometric matching algorithms lead to a substantial performance gain, both in running time and in memory consumption, over their purely combinatorial counterparts. Moreover, our implementation significantly outperforms the only other implementation available for comparing persistence diagrams.

Estimated D2--DT--T2 phase diagram in the three-phase region

International Nuclear Information System (INIS)

Souers, P.C.; Hickman, R.G.; Tsugawa, R.T.

1976-01-01

A composite of experimental eH 2 -D 2 phase-diagram data at the three-phase line is assembled from the literature. The phase diagram is a smooth cigar shape without a eutectic point, indicating complete miscibility of liquid and solid phases. Additional data is used to estimate the D 2 -T 2 , D 2 DT, and DT-T 2 binary phase diagrams. These are assembled into the ternary D 2 -DT-T 2 phase diagram. A surface representing the chemical equilibrium of the three species is added to the phase diagram. At chemical equilibrium, it is estimated that 50-50 liquid D-T at 19.7 0 K is in equilibrium with 42 mole percent T vapor and 54 percent T solid. Infrared spectroscopy is suggested as a means of component analysis of liquid and solid mixtures

Phase diagram of supercooled water confined to hydrophilic nanopores

Science.gov (United States)

Limmer, David T.; Chandler, David

2012-07-01

We present a phase diagram for water confined to cylindrical silica nanopores in terms of pressure, temperature, and pore radius. The confining cylindrical wall is hydrophilic and disordered, which has a destabilizing effect on ordered water structure. The phase diagram for this class of systems is derived from general arguments, with parameters taken from experimental observations and computer simulations and with assumptions tested by computer simulation. Phase space divides into three regions: a single liquid, a crystal-like solid, and glass. For large pores, radii exceeding 1 nm, water exhibits liquid and crystal-like behaviors, with abrupt crossovers between these regimes. For small pore radii, crystal-like behavior is unstable and water remains amorphous for all non-zero temperatures. At low enough temperatures, these states are glasses. Several experimental results for supercooled water can be understood in terms of the phase diagram we present.

Sequence Algebra, Sequence Decision Diagrams and Dynamic Fault Trees

International Nuclear Information System (INIS)

Rauzy, Antoine B.

2011-01-01

A large attention has been focused on the Dynamic Fault Trees in the past few years. By adding new gates to static (regular) Fault Trees, Dynamic Fault Trees aim to take into account dependencies among events. Merle et al. proposed recently an algebraic framework to give a formal interpretation to these gates. In this article, we extend Merle et al.'s work by adopting a slightly different perspective. We introduce Sequence Algebras that can be seen as Algebras of Basic Events, representing failures of non-repairable components. We show how to interpret Dynamic Fault Trees within this framework. Finally, we propose a new data structure to encode sets of sequences of Basic Events: Sequence Decision Diagrams. Sequence Decision Diagrams are very much inspired from Minato's Zero-Suppressed Binary Decision Diagrams. We show that all operations of Sequence Algebras can be performed on this data structure.

CALPHAD calculation of phase diagrams : a comprehensive guide

CERN Document Server

Saunders, N; Miodownik, A P

1998-01-01

This monograph acts as a benchmark to current achievements in the field of Computer Coupling of Phase Diagrams and Thermochemistry, often called CALPHAD which is an acronym for Computer CALculation of PHAse Diagrams. It also acts as a guide to both the basic background of the subject area and the cutting edge of the topic, combining comprehensive discussions of the underlying physical principles of the CALPHAD method with detailed descriptions of their application to real complex multi-component materials. Approaches which combine both thermodynamic and kinetic models to interpret non-equilibrium phase transformations are also reviewed.

Basic principles of Hasse diagram technique in chemistry.

Science.gov (United States)

Brüggemann, Rainer; Voigt, Kristina

2008-11-01

Principles of partial order applied to ranking are explained. The Hasse diagram technique (HDT) is the application of partial order theory based on a data matrix. In this paper, HDT is introduced in a stepwise procedure, and some elementary theorems are exemplified. The focus is to show how the multivariate character of a data matrix is realized by HDT and in which cases one should apply other mathematical or statistical methods. Many simple examples illustrate the basic theoretical ideas. Finally, it is shown that HDT is a useful alternative for the evaluation of antifouling agents, which was originally performed by amoeba diagrams.

Oak Ridge National Laboratory Technology Logic Diagram. Volume 2, Technology Logic Diagram: Part B, Remedial Action

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

The Oak Ridge National Laboratory Technology Logic Diagram (TLD) was developed to provide a decision support tool that relates environmental restoration (ER) and waste management (WM) problems at Oak Ridge National Laboratory (ORNL) to potential technologies that can remediate these problems. The TLD identifies the research, development, demonstration, testing, and evaluation needed to develop these technologies to a state that allows technology transfer and application to decontamination and decommissioning (D&D), remedial action (RA), and WM activities. The TLD consists of three fundamentally separate volumes: Vol. 1 (Technology Evaluation), Vol. 2 (Technology Logic Diagram), and Vol. 3 (Technology Evaluation Data Sheets). Part A of Vols. 1. and 2 focuses on D&D. Part B of Vols. 1 and 2 focuses on the RA of contaminated facilities. Part C of Vols. 1 and 2 focuses on WM. Each part of Vol. 1 contains an overview of the TLD, an explanation of the program-specific responsibilities, a review of identified technologies, and the rankings of remedial technologies. Volume 2 (Pts. A, B, and C) contains the logic linkages among EM goals, environmental problems, and the various technologies that have the potential to solve these problems. Volume 3 (Pts. A, B, and C) contains the TLD data sheets. Remedial action is the focus of Vol. 2, Pt. B, which has been divided into the three necessary subelements of the RA: characterization, RA, and robotics and automation. Each of these sections address general ORNL problems, which are then broken down by problem area/constituents and linked to potential remedial technologies. The diagrams also contain summary information about a technology`s status, its science and technology needs, and its implementation needs.

49 CFR Appendix B to Part 230 - Diagrams and Drawings

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Diagrams and Drawings B Appendix B to Part 230 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION... to Part 230—Diagrams and Drawings ER17No99.015 ER17No99.016 ER17No99.017 ER17No99.018 ER17No99.019...

Counting loop diagrams: computational complexity of higher-order amplitude evaluation

International Nuclear Information System (INIS)

Eijk, E. van; Kleiss, R.; Lazopoulos, A.

2004-01-01

We discuss the computational complexity of the perturbative evaluation of scattering amplitudes, both by the Caravaglios-Moretti algorithm and by direct evaluation of the individual diagrams. For a self-interacting scalar theory, we determine the complexity as a function of the number of external legs. We describe a method for obtaining the number of topologically inequivalent Feynman graphs containing closed loops, and apply this to 1- and 2-loop amplitudes. We also compute the number of graphs weighted by their symmetry factors, thus arriving at exact and asymptotic estimates for the average symmetry factor of diagrams. We present results for the asymptotic number of diagrams up to 10 loops, and prove that the average symmetry factor approaches unity as the number of external legs becomes large. (orig.)

A dynamical mechanism for the hairpin diagram

International Nuclear Information System (INIS)

Chang Chaohsi; Guo Xinheng; Li Xueqian.

1989-09-01

Based on the non-valence quark-antiquark and gluon constituent structure of mesons we give a reasonable dynamical mechanism which can induce the hairpin diagram without violating the well-observed OZI rule. We calculate the hairpin amplitudes of D deg. → K-bar deg.η and K-bar deg.η' normalized by D deg. → K-bar deg.π deg. and have found that the hairpin diagram can give rise to substantial contribution to the decays where a meson with a SU(3) flavor singlet component is involved in the final state. In this scenario, we also obtain the branching ratio of D deg. → K-bar deg. φ as 0.55% in comparison with the experimental data of 0.83%. (autor). 33 refs, 3 figs

Unraveling the history of complex zoned garnets from the North Motagua Mélange (Guatemala)

Science.gov (United States)

Barickman, M. H.; Martin, C.; Flores, K. E.; Harlow, G. E.; Bonnet, G.

2016-12-01

The Guatemala Suture Zone (GSZ) is situated in central Guatemala, between the North American and Caribbean plates. Two serpentinite mélanges straddle the Motagua Fault system: the North Motagua Mélange (NMM) and the South Motagua Mélange (SMM). In this study, chemically zoned garnet grains from four eclogite blocks from the NMM were analyzed by EMPA for major elements and LA-ICP-MS for trace elements to unravel the geological history of the eclogites. These eclogites typically consist of euhedral to subhedral garnets, partly retrogressed omphacite grains, and accessory minerals such as phengite and epidote as inclusions in garnet. EBSD was employed to examine apparent garnet inclusions in garnet. The garnet grains in NMM eclogites display complex chemical zonations: all grains roughly show a spessartine-rich core, an almandine-rich core and/or intermediate zone, and a pyrope and grossular-rich rim. Additionally, crystal resorption can be observed between the different zones, and the pyrope-grossular rim can display oscillatory zoning. Finally, grossular-rich zones (crystallographically syntactic) within garnet are present in all studied samples. REE and spider diagrams do not show any significant difference in the patterns of the different zones within the garnet, or indicating that the chemical environment from which each garnet zone grew was broadly the same. The lack of significant variation in LILE content indicates that a fluid influx during garnet growth is unlikely. Consequently, we interpret that garnet grains grew in a largely closed system; however, the presence of the grossular-rich zones, argues for occasional excursions into conditions when either two garnets crystallized or Ca-rich overgrowths that were largely resorbed prior to subsequent continued garnet growth.

Kelp diagrams : Point set membership visualization

NARCIS (Netherlands)

Dinkla, K.; Kreveld, van M.J.; Speckmann, B.; Westenberg, M.A.

2012-01-01

We present Kelp Diagrams, a novel method to depict set relations over points, i.e., elements with predefined positions. Our method creates schematic drawings and has been designed to take aesthetic quality, efficiency, and effectiveness into account. This is achieved by a routing algorithm, which

Visualizing the Bayesian 2-test case: The effect of tree diagrams on medical decision making.

Science.gov (United States)

Binder, Karin; Krauss, Stefan; Bruckmaier, Georg; Marienhagen, Jörg

2018-01-01

In medicine, diagnoses based on medical test results are probabilistic by nature. Unfortunately, cognitive illusions regarding the statistical meaning of test results are well documented among patients, medical students, and even physicians. There are two effective strategies that can foster insight into what is known as Bayesian reasoning situations: (1) translating the statistical information on the prevalence of a disease and the sensitivity and the false-alarm rate of a specific test for that disease from probabilities into natural frequencies, and (2) illustrating the statistical information with tree diagrams, for instance, or with other pictorial representation. So far, such strategies have only been empirically tested in combination for "1-test cases", where one binary hypothesis ("disease" vs. "no disease") has to be diagnosed based on one binary test result ("positive" vs. "negative"). However, in reality, often more than one medical test is conducted to derive a diagnosis. In two studies, we examined a total of 388 medical students from the University of Regensburg (Germany) with medical "2-test scenarios". Each student had to work on two problems: diagnosing breast cancer with mammography and sonography test results, and diagnosing HIV infection with the ELISA and Western Blot tests. In Study 1 (N = 190 participants), we systematically varied the presentation of statistical information ("only textual information" vs. "only tree diagram" vs. "text and tree diagram in combination"), whereas in Study 2 (N = 198 participants), we varied the kinds of tree diagrams ("complete tree" vs. "highlighted tree" vs. "pruned tree"). All versions were implemented in probability format (including probability trees) and in natural frequency format (including frequency trees). We found that natural frequency trees, especially when the question-related branches were highlighted, improved performance, but that none of the corresponding probabilistic visualizations did.

Advanced quantum theory and its applications through Feynman diagrams

International Nuclear Information System (INIS)

Scadron, M.D.

1979-01-01

The two themes of scattering diagrams and the fundamental forces characterize this book. Transformation theory is developed to review the concepts of nonrelativistic quantum mechanics and to formulate the relativistic Klein-Gordon, Maxwell, and Dirac wave equations for relativistic spin-0, massless spin-1, and spin-1/2 particles, respectively. The language of group theory is used to write relativistic Lorentz transformations in a form similar to ordinary rotations and to describe the important discrete symmetries of C, P, and T. Then quantum mechanics is reformulated in the language of scattering theory, with the momentum-space S matrix replacing the coordinate-space hamiltonian as the central dynamical operator. Nonrelativistic perturbation scattering diagrams are then developed, and simple applications given for nuclear, atomic, and solid-state scattering problems. Next, relativistic scattering diagrams built up from covariant Feynman propagators and vertices in a manner consistent with the CPT theorem are considered. The theory is systematically applied to the lowest-order fundamental electromagnetic, strong, weak, and gravitational interactions. Finally, the use of higher-order Feynman diagrams to explain more detailed aspects of quantum electrodynamics (QED) and strong-interaction elementary-particle physics is surveyed. Throughout, the notion of currents is used to exploit the underlying symmetries and dynamical interactions of the various quantum forces. 258 references, 77 figures, 1 table

Drawing theories apart the dispersion of Feynman diagrams in postwar physics

CERN Document Server

Kaiser, David

2005-01-01

Winner of the 2007 Pfizer Prize from the History of Science Society. Feynman diagrams have revolutionized nearly every aspect of theoretical physics since the middle of the twentieth century. Introduced by the American physicist Richard Feynman (1918-88) soon after World War II as a means of simplifying lengthy calculations in quantum electrodynamics, they soon gained adherents in many branches of the discipline. Yet as new physicists adopted the tiny line drawings, they also adapted the diagrams and introduced their own interpretations. Drawing Theories Apart traces how generations of young theorists learned to frame their research in terms of the diagrams—and how both the diagrams and their users were molded in the process.Drawing on rich archival materials, interviews, and more than five hundred scientific articles from the period, Drawing Theories Apart uses the Feynman diagrams as a means to explore the development of American postwar physics. By focusing on the ways young physicists learned new calcul...

Automated discovery and construction of surface phase diagrams using machine learning

International Nuclear Information System (INIS)

Ulissi, Zachary W.; Singh, Aayush R.; Tsai, Charlie

2016-01-01

Surface phase diagrams are necessary for understanding surface chemistry in electrochemical catalysis, where a range of adsorbates and coverages exist at varying applied potentials. These diagrams are typically constructed using intuition, which risks missing complex coverages and configurations at potentials of interest. More accurate cluster expansion methods are often difficult to implement quickly for new surfaces. We adopt a machine learning approach to rectify both issues. Using a Gaussian process regression model, the free energy of all possible adsorbate coverages for surfaces is predicted for a finite number of adsorption sites. Our result demonstrates a rational, simple, and systematic approach for generating accurate free-energy diagrams with reduced computational resources. Finally, the Pourbaix diagram for the IrO_2(110) surface (with nine coverages from fully hydrogenated to fully oxygenated surfaces) is reconstructed using just 20 electronic structure relaxations, compared to approximately 90 using typical search methods. Similar efficiency is demonstrated for the MoS_2 surface.

Accuracy of Currently Used Paper Burn Diagram vs a Three-Dimensional Computerized Model.

Science.gov (United States)

Benjamin, Nicole C; Lee, Jong O; Norbury, William B; Branski, Ludwik K; Wurzer, Paul; Jimenez, Carlos J; Benjamin, Debra A; Herndon, David N

Burn units have historically used paper diagrams to estimate percent burn; however, unintentional errors can occur. The use of a computer program that incorporates wound mapping from photographs onto a three-dimensional (3D) human diagram could decrease subjectivity in preparing burn diagrams and subsequent calculations of TBSA burned. Analyses were done on 19 burned patients who had an estimated TBSA burned of ≥20%. The patients were admitted to Shriners Hospitals for Children or the University of Texas Medical Branch in Galveston, Texas, from July 2012 to September 2013 for treatment. Digital photographs were collected before the patient's first surgery. Using BurnCase 3D (RISC Software GmbH, Hagenberg, Austria), a burn mapping software, the user traced partial- and full-thickness burns from photographs. The program then superimposed tracings onto a 3D model and calculated percent burned. The results were compared with the Lund and Browder diagrams completed after the first operation. A two-tailed t-test was used to calculate statistical differences. For partial-thickness burns, burn sizes calculated using Lund and Browder diagrams were significantly larger than those calculated using BurnCase 3D (15% difference, P < .01). The opposite was found for full-thickness burns, with burn sizes being smaller when calculated using Lund and Browder diagrams (11% difference, P < .05). In conclusion, substantial differences exist in percent burn estimations derived from BurnCase 3D and paper diagrams. In our studied cohort, paper diagrams were associated with overestimation of partial-thickness burn size and underestimation of full-thickness burn size. Additional studies comparing BurnCase 3D with other commonly used methods are warranted.

Low-frequency phase diagram of irradiated graphene and a periodically driven spin-1/2 X Y chain

Science.gov (United States)

Mukherjee, Bhaskar; Mohan, Priyanka; Sen, Diptiman; Sengupta, K.

2018-05-01

We study the Floquet phase diagram of two-dimensional Dirac materials such as graphene and the one-dimensional (1D) spin-1/2 X Y model in a transverse field in the presence of periodic time-varying terms in their Hamiltonians in the low drive frequency (ω ) regime where standard 1 /ω perturbative expansions fail. For graphene, such periodic time-dependent terms are generated via the application of external radiation of amplitude A0 and time period T =2 π /ω , while for the 1D X Y model, they result from a two-rate drive protocol with a time-dependent magnetic field and nearest-neighbor couplings between the spins. Using the adiabatic-impulse method, whose predictions agree almost exactly with the corresponding numerical results in the low-frequency regime, we provide several semianalytic criteria for the occurrence of changes in the topology of the phase bands (eigenstates of the evolution operator U ) of such systems. For irradiated graphene, we point out the role of the symmetries of the instantaneous Hamiltonian H (t ) and the evolution operator U behind such topology changes. Our analysis reveals that at low frequencies, topology changes of irradiated graphene phase bands may also happen at t =T /3 and2 T /3 (apart from t =T ) showing the necessity of analyzing the phase bands of the system for obtaining its phase diagrams. We chart out the phase diagrams at t =T /3 ,2 T /3 ,and T , where such topology changes occur, as a function of A0 and T using exact numerics, and compare them with the prediction of the adiabatic-impulse method. We show that several characteristics of these phase diagrams can be analytically understood from results obtained using the adiabatic-impulse method and point out the crucial contribution of the high-symmetry points in the graphene Brillouin zone to these diagrams. We study the modes that can appear at the edges of a finite-width strip of graphene and show that the change in the number of such modes agrees with the change in the

Penerapan Reverse Engineering Dalam Penentuan Pola Interaksi Sequence Diagram Pada Sampel Aplikasi Android

Directory of Open Access Journals (Sweden)

Vierdy Sulfianto Rahmadani

2015-04-01

Full Text Available The purpose of this research is to apply the application of reverse engineering to determine interaction patterns of the Sequence diagram that can be used by system analysts as a template for designing UML sequence diagrams. Sample applications from android are used as dataset for reverse engineering and pattern identification. The first step is collecting application datasets. The next stage is identifying the features and applications activity, reverse engineering to obtain a sequence diagram model, and then synthesize all of the models into an interaction pattern of sequence diagram. The final step is to test the patterns by implementing it in an application development case stud. The evaluation results concludes that interaction patterns of sequence diagram designs obtained in reverse engineering steps is able to be implemented in software development that contained similar features with the obtained features in this research.

Safety-barrier diagrams as a tool for modelling safety of hydrogen applications

DEFF Research Database (Denmark)

Duijm, Nijs Jan; Markert, Frank

2009-01-01

Safety-barrier diagrams have proven to be a useful tool in documenting the safety measures taken to prevent incidents and accidents in process industry. Especially during the introduction of new hydrogen technologies or applications, as e.g. hydrogen refuelling stations, safety-barrier diagrams...... are considered a valuable supplement to other traditional risk analysis tools to support the communication with authorities and other stakeholders during the permitting process. Another advantage of safety-barrier diagrams is that they highlight the importance of functional and reliable safety barriers in any...... system and here is a direct focus on those barriers that need to be subject to safety management in terms of design and installation, operational use, inspection and monitoring, and maintenance. Safety-barrier diagrams support both quantitative and qualitative approaches. The paper will describe...

Galaxy emission line classification using three-dimensional line ratio diagrams

Energy Technology Data Exchange (ETDEWEB)

Vogt, Frédéric P. A.; Dopita, Michael A.; Kewley, Lisa J.; Sutherland, Ralph S. [Research School of Astronomy and Astrophysics, Australian National University, Canberra, ACT 2611 (Australia); Scharwächter, Julia [Observatoire de Paris, LERMA (CNRS: UMR8112), 61 Av. de l' Observatoire, F-75014 Paris (France); Basurah, Hassan M.; Ali, Alaa; Amer, Morsi A., E-mail: frederic.vogt@anu.edu.au [Astronomy Department, King Abdulaziz University, P.O. Box 80203, Jeddah (Saudi Arabia)

2014-10-01

Two-dimensional (2D) line ratio diagnostic diagrams have become a key tool in understanding the excitation mechanisms of galaxies. The curves used to separate the different regions—H II-like or excited by an active galactic nucleus (AGN)—have been refined over time but the core technique has not evolved significantly. However, the classification of galaxies based on their emission line ratios really is a multi-dimensional problem. Here we exploit recent software developments to explore the potential of three-dimensional (3D) line ratio diagnostic diagrams. We introduce the ZQE diagrams, which are a specific set of 3D diagrams that separate the oxygen abundance and the ionization parameter of H II region-like spectra and also enable us to probe the excitation mechanism of the gas. By examining these new 3D spaces interactively, we define the ZE diagnostics, a new set of 2D diagnostics that can provide the metallicity of objects excited by hot young stars and that cleanly separate H II region-like objects from the different classes of AGNs. We show that these ZE diagnostics are consistent with the key log [N II]/Hα versus log [O III]/Hβ diagnostic currently used by the community. They also have the advantage of attaching a probability that a given object belongs to one class or the other. Finally, we discuss briefly why ZQE diagrams can provide a new way to differentiate and study the different classes of AGNs in anticipation of a dedicated follow-up study.

Universal block diagram based modeling and simulation schemes for fractional-order control systems.

Science.gov (United States)

Bai, Lu; Xue, Dingyü

2017-05-08

Universal block diagram based schemes are proposed for modeling and simulating the fractional-order control systems in this paper. A fractional operator block in Simulink is designed to evaluate the fractional-order derivative and integral. Based on the block, the fractional-order control systems with zero initial conditions can be modeled conveniently. For modeling the system with nonzero initial conditions, the auxiliary signal is constructed in the compensation scheme. Since the compensation scheme is very complicated, therefore the integrator chain scheme is further proposed to simplify the modeling procedures. The accuracy and effectiveness of the schemes are assessed in the examples, the computation results testify the block diagram scheme is efficient for all Caputo fractional-order ordinary differential equations (FODEs) of any complexity, including the implicit Caputo FODEs. Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.

Partial chord diagrams and matrix models

DEFF Research Database (Denmark)

Andersen, Jørgen Ellegaard; Fuji, Hiroyuki; Manabe, Masahide

In this article, the enumeration of partial chord diagrams is discussed via matrix model techniques. In addition to the basic data such as the number of backbones and chords, we also consider the Euler characteristic, the backbone spectrum, the boundary point spectrum, and the boundary length spe...

Folded diagram theory, time-dependent approach of Johnson and Baranger

International Nuclear Information System (INIS)

Johnson, M.B.

1975-01-01

The folded diagram expansion of Brandow and extensively developed by Johnson and Baranger is discussed in detail. The time-dependent approach is reviewed through Feynman-Goldstone diagrams to establish the conventions used. The problem of calculating the effective interaction for nuclei beyond 208 Pb is then considered as an example. Finally, examples are given which show how to do the time integrations. (17 figures) (SDF)

Problem-solving tools for analyzing system problems. The affinity map and the relationship diagram.

Science.gov (United States)

Lepley, C J

1998-12-01

The author describes how to use two management tools, an affinity map and a relationship diagram, to define and analyze aspects of a complex problem in a system. The affinity map identifies the key influencing elements of the problem, whereas the relationship diagram helps to identify the area that is the most important element of the issue. Managers can use the tools to draw a map of problem drivers, graphically display the drivers in a diagram, and use the diagram to develop a cause-and-effect relationship.

Determination of the quaternary phase diagram of the water-ethylene glycol-sucrose-NaCl system and a comparison between two theoretical methods for synthetic phase diagrams.

Science.gov (United States)

Han, Xu; Liu, Yang; Critser, John K

2010-08-01

Characterization of the thermodynamic properties of multi-solute aqueous solutions is of critical importance for biological and biochemical research. For example, the phase diagrams of aqueous systems, containing salts, saccharides, and plasma membrane permeating solutes, are indispensible in the field of cryobiology and pharmacology. However, only a few ternary phase diagrams are currently available for these systems. In this study, an auto-sampler differential scanning calorimeter (DSC) was used to determine the quaternary phase diagram of the water-ethylene glycol-sucrose-NaCl system. To improve the accuracy of melting point measurement, a "mass-redemption" method was also applied for the DSC technique. Base on the analyses of these experimental data, a comparison was made between the two practical approaches to generate phase diagrams of multi-solute solutions from those of single-solute solutions: the summation of cubic polynomial melting point equations versus the use of osmotic virial equations with cross coefficients. The calculated values of the model standard deviations suggested that both methods are satisfactory for characterizing this quaternary system. (c) 2010 Elsevier Inc. All rights reserved.

Generalized internal multiple imaging (GIMI) using Feynman-like diagrams

KAUST Repository

Zuberi, M. A. H.; Alkhalifah, Tariq Ali

2014-01-01

Single scattering events recorded in surface seismic data do not fully illuminate the subsurface structure, especially if it is complicated. In such cases, multiple internal scatterings (internal multiples) can help improve the illumination. We devise a generalized internal multiple imaging (GIMI) procedure that maps internal multiple energy to their true location with a relatively mild addition to the computational cost. GIMI theory relies heavily on seismic interferometry, which often involves cumbersome algebra, especially when one is dealing with high-order terms in the perturbation series. To make the derivations, and inference of the results easier, we introduce Feynman-like diagrams to represent different terms of the perturbation series (solution to the Lippman–Schwinger equation). The rules we define for the diagrams allow operations like convolution and cross-correlation in the series to be compressed in diagram form. The application of the theory to a double scattering example demonstrates the power of the method.

The limit shape problem for ensembles of Young diagrams

CERN Document Server

Hora, Akihito

2016-01-01

This book treats ensembles of Young diagrams originating from group-theoretical contexts and investigates what statistical properties are observed there in a large-scale limit. The focus is mainly on analyzing the interesting phenomenon that specific curves appear in the appropriate scaling limit for the profiles of Young diagrams. This problem is regarded as an important origin of recent vital studies on harmonic analysis of huge symmetry structures. As mathematics, an asymptotic theory of representations is developed of the symmetric groups of degree n as n goes to infinity. The framework of rigorous limit theorems (especially the law of large numbers) in probability theory is employed as well as combinatorial analysis of group characters of symmetric groups and applications of Voiculescu's free probability. The central destination here is a clear description of the asymptotic behavior of rescaled profiles of Young diagrams in the Plancherel ensemble from both static and dynamic points of view.

Generalized internal multiple imaging (GIMI) using Feynman-like diagrams

KAUST Repository

Zuberi, M. A. H.

2014-05-19

Single scattering events recorded in surface seismic data do not fully illuminate the subsurface structure, especially if it is complicated. In such cases, multiple internal scatterings (internal multiples) can help improve the illumination. We devise a generalized internal multiple imaging (GIMI) procedure that maps internal multiple energy to their true location with a relatively mild addition to the computational cost. GIMI theory relies heavily on seismic interferometry, which often involves cumbersome algebra, especially when one is dealing with high-order terms in the perturbation series. To make the derivations, and inference of the results easier, we introduce Feynman-like diagrams to represent different terms of the perturbation series (solution to the Lippman–Schwinger equation). The rules we define for the diagrams allow operations like convolution and cross-correlation in the series to be compressed in diagram form. The application of the theory to a double scattering example demonstrates the power of the method.

User testing of an adaptation of fishbone diagrams to depict results of systematic reviews.

Science.gov (United States)

Gartlehner, Gerald; Schultes, Marie-Therese; Titscher, Viktoria; Morgan, Laura C; Bobashev, Georgiy V; Williams, Peyton; West, Suzanne L

2017-12-12

Summary of findings tables in systematic reviews are highly informative but require epidemiological training to be interpreted correctly. The usage of fishbone diagrams as graphical displays could offer researchers an effective approach to simplify content for readers with limited epidemiological training. In this paper we demonstrate how fishbone diagrams can be applied to systematic reviews and present the results of an initial user testing. Findings from two systematic reviews were graphically depicted in the form of the fishbone diagram. To test the utility of fishbone diagrams compared with summary of findings tables, we developed and pilot-tested an online survey using Qualtrics. Respondents were randomized to the fishbone diagram or a summary of findings table presenting the same body of evidence. They answered questions in both open-ended and closed-answer formats; all responses were anonymous. Measures of interest focused on first and second impressions, the ability to find and interpret critical information, as well as user experience with both displays. We asked respondents about the perceived utility of fishbone diagrams compared to summary of findings tables. We analyzed quantitative data by conducting t-tests and comparing descriptive statistics. Based on real world systematic reviews, we provide two different fishbone diagrams to show how they might be used to display complex information in a clear and succinct manner. User testing on 77 students with basic epidemiological training revealed that participants preferred summary of findings tables over fishbone diagrams. Significantly more participants liked the summary of findings table than the fishbone diagram (71.8% vs. 44.8%; p testing, however, did not support the utility of such graphical displays.

Influence Diagram Use With Respect to Technology Planning and Investment

Science.gov (United States)

Levack, Daniel J. H.; DeHoff, Bryan; Rhodes, Russel E.

2009-01-01

Influence diagrams are relatively simple, but powerful, tools for assessing the impact of choices or resource allocations on goals or requirements. They are very general and can be used on a wide range of problems. They can be used for any problem that has defined goals, a set of factors that influence the goals or the other factors, and a set of inputs. Influence diagrams show the relationship among a set of results and the attributes that influence them and the inputs that influence the attributes. If the results are goals or requirements of a program, then the influence diagram can be used to examine how the requirements are affected by changes to technology investment. This paper uses an example to show how to construct and interpret influence diagrams, how to assign weights to the inputs and attributes, how to assign weights to the transfer functions (influences), and how to calculate the resulting influences of the inputs on the results. A study is also presented as an example of how using influence diagrams can help in technology planning and investment. The Space Propulsion Synergy Team (SPST) used this technique to examine the impact of R&D spending on the Life Cycle Cost (LCC) of a space transportation system. The question addressed was the effect on the recurring and the non-recurring portions of LCC of the proportion of R&D resources spent to impact technology objectives versus the proportion spent to impact operational dependability objectives. The goals, attributes, and the inputs were established. All of the linkages (influences) were determined. The weighting of each of the attributes and each of the linkages was determined. Finally the inputs were varied and the impacts on the LCC determined and are presented. The paper discusses how each of these was accomplished both for credibility and as an example for future studies using influence diagrams for technology planning and investment planning.

The geometry of on-shell diagrams

Science.gov (United States)

Franco, Sebastián; Galloni, Daniele; Mariotti, Alberto

2014-08-01

The fundamental role of on-shell diagrams in quantum field theory has been recently recognized. On-shell diagrams, or equivalently bipartite graphs, provide a natural bridge connecting gauge theory to powerful mathematical structures such as the Grassmannian. We perform a detailed investigation of the combinatorial and geometric objects associated to these graphs. We mainly focus on their relation to polytopes and toric geometry, the Grassmannian and its stratification. Our work extends the current understanding of these connections along several important fronts, most notably eliminating restrictions imposed by planarity, positivity, reducibility and edge removability. We illustrate our ideas with several explicit examples and introduce concrete methods that considerably simplify computations. We consider it highly likely that the structures unveiled in this article will arise in the on-shell study of scattering amplitudes beyond the planar limit. Our results can be conversely regarded as an expansion in the understanding of the Grassmannian in terms of bipartite graphs.

Grotrian diagrams for highly ionized molybdenum Mo VI through Mo XLII

International Nuclear Information System (INIS)

Shirai, Toshizo; Sugar, J.; Wiese, W.L.

1997-07-01

Grotrian diagrams are presented to provide graphical overviews for 1,930 spectral lines of highly ionized molybdenum, Mo VI through Mo XLII. In the usual diagram display such as that by Bashkin and Stoner (North-Holland, Amsterdam, 1975), the density of transitions is often too high to allow each transition to be drawn separately. Here in our modified diagrams, the transitions are also represented by lines connecting the upper and lower energy levels, but the lower energy levels are extended and repeated for successive configurations as needed. As a sequence, dense packing is avoided and all lines in a multiplet can be accommodated. (author)

Grotrian diagrams for highly ionized cobalt Co VIII through Co XXVII

Energy Technology Data Exchange (ETDEWEB)

Shirai, Toshizo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Sugar, J.; Wiese, W.L.

1997-07-01

Grotrian diagrams are presented to provide graphical overviews for 1,247 spectral lines of highly ionized cobalt, Co VIII through Co XXVII. In the usual diagram display such as that by Bashkin and Stoner (North-Holland, Amsterdam, 1975), the density of transitions is often too high to allow each transition to be drawn separately. Here in our modified diagrams, the transitions are also represented by lines connecting the upper and lower energy levels, but the lower energy levels are extended and repeated for successive configurations as needed. As a sequence, dense packing is avoided and all lines in a multiplet can be accommodated. (author)

One-particle many-body Green's function theory: Algebraic recursive definitions, linked-diagram theorem, irreducible-diagram theorem, and general-order algorithms.

Science.gov (United States)

Hirata, So; Doran, Alexander E; Knowles, Peter J; Ortiz, J V

2017-07-28

A thorough analytical and numerical characterization of the whole perturbation series of one-particle many-body Green's function (MBGF) theory is presented in a pedagogical manner. Three distinct but equivalent algebraic (first-quantized) recursive definitions of the perturbation series of the Green's function are derived, which can be combined with the well-known recursion for the self-energy. Six general-order algorithms of MBGF are developed, each implementing one of the three recursions, the ΔMPn method (where n is the perturbation order) [S. Hirata et al., J. Chem. Theory Comput. 11, 1595 (2015)], the automatic generation and interpretation of diagrams, or the numerical differentiation of the exact Green's function with a perturbation-scaled Hamiltonian. They all display the identical, nondivergent perturbation series except ΔMPn, which agrees with MBGF in the diagonal and frequency-independent approximations at 1≤n≤3 but converges at the full-configuration-interaction (FCI) limit at n=∞ (unless it diverges). Numerical data of the perturbation series are presented for Koopmans and non-Koopmans states to quantify the rate of convergence towards the FCI limit and the impact of the diagonal, frequency-independent, or ΔMPn approximation. The diagrammatic linkedness and thus size-consistency of the one-particle Green's function and self-energy are demonstrated at any perturbation order on the basis of the algebraic recursions in an entirely time-independent (frequency-domain) framework. The trimming of external lines in a one-particle Green's function to expose a self-energy diagram and the removal of reducible diagrams are also justified mathematically using the factorization theorem of Frantz and Mills. Equivalence of ΔMPn and MBGF in the diagonal and frequency-independent approximations at 1≤n≤3 is algebraically proven, also ascribing the differences at n = 4 to the so-called semi-reducible and linked-disconnected diagrams.

Maunder's Butterfly Diagram in the 21st Century

Science.gov (United States)

Hathaway, David H.

2005-01-01

E. Walter Maunder created his first "Butterfly Diagram" showing the equatorward drift of the sunspot latitudes over the course of each of two solar cycles in 1903. This diagram was constructed from data obtained through the Royal Greenwich Observatory (RGO) starting in 1874. The RGO continued to acquire data up until 1976. Fortunately, the US Air Force (USAF) and the US National Oceanic and Atmospheric Administration (NOAA) have continued to acquire similar data since that time. This combined RGO/USAF/NOAA dataset on sunspot group positions and areas now extends virtually unbroken from the 19th century to the 21st century. The data represented in the Butterfly Diagram contain a wealth of information about solar activity and the solar cycle. Solar activity (as represented by the sunspots) appears at mid-latitudes at the start of each cycle. The bands of activity spread in each hemisphere and then drift toward the equator as the cycle progresses. Although the equator itself tends to be avoided, the spread of activity reaches the equator at about the time of cycle maximum. The cycles overlap at minimum with old cycle spots appearing near the equator while new cycle spots emerge in the mid-latitudes. Large amplitude cycles tend to have activity starting at higher latitudes with the activity spreading to higher latitudes as well. Large amplitude cycles also tend to be preceded by earlier cycles with faster drift rates. These drift rates may be tied to the Sun s meridional circulation - a component in many dynamo theories for the origin of the sunspot cycle. The Butterfly Diagram must be reproduced in any successful dynamo model for the Sun.

A diagram approach to character formulae for finite and compact groups

International Nuclear Information System (INIS)

Kibler, M.; Elbaz, E.

1978-06-01

Some basic relations for the representation theory and the Wigner-Racah algebra of a finite or compact continuous group are discussed and transcribed in terms of diagrams. Special emphasis is placed on the case of a simply reducible group and all the diagrams are applicable to SU 2 without any change

Interaction diagrams for composite columns exposed to fire

Directory of Open Access Journals (Sweden)

Milanović Milivoje

2014-01-01

Full Text Available The bearing capacity of the cross section of composite column in fire conditions through changes in the interaction diagram 'bending moment-axialforce' were analyzed in this paper. The M-N interaction diagram presents the relationship between the intensities of the bending moment and the axial force as actions on the column cross section, or the relationship between the design value of the plastic resistance to axial compression of the total cross-section Npl, Rd and the design value of the bending moment resistance Mpl, Rd. It is well known that the temperature increase causes decrease of the load-bearing characteristics of the constitutive materials. This effect directly reflects on the reduction of the axial force and the bending moment that could be accepted by the column cross section. Interaction diagrams for three different types of column cross sections for five different maximal temperatures developed during the fire action were defined. For that purpose the software package SAFIR was used. The columns, materials and load characteristics, as well as all other terms and conditions, were taken in accordance with the relevant Eurocodes and the theory of composite columns.

Highly Accurate Calculations of the Phase Diagram of Cold Lithium

Science.gov (United States)

Shulenburger, Luke; Baczewski, Andrew

The phase diagram of lithium is particularly complicated, exhibiting many different solid phases under the modest application of pressure. Experimental efforts to identify these phases using diamond anvil cells have been complemented by ab initio theory, primarily using density functional theory (DFT). Due to the multiplicity of crystal structures whose enthalpy is nearly degenerate and the uncertainty introduced by density functional approximations, we apply the highly accurate many-body diffusion Monte Carlo (DMC) method to the study of the solid phases at low temperature. These calculations span many different phases, including several with low symmetry, demonstrating the viability of DMC as a method for calculating phase diagrams for complex solids. Our results can be used as a benchmark to test the accuracy of various density functionals. This can strengthen confidence in DFT based predictions of more complex phenomena such as the anomalous melting behavior predicted for lithium at high pressures. Sandia National Laboratories is a multi-program laboratory managed and operated by Sandia Corporation, a wholly owned subsidiary of Lockheed Martin Corporation, for the U.S. DOE's National Nuclear Security Administration under contract DE-AC04-94AL85000.

Basics of introduction to Feynman diagrams and electroweak interactions physics

International Nuclear Information System (INIS)

Bilenky, S.M.; Mikhov, S.G.

1994-01-01

The Feynman diagrams are the main computational method for the evaluation of the matrix elements of different processes. Although it is a perturbative method, its significance is not restricted to perturbation theory only. In this book, the elements of quantum field theory, the Feynman diagram method, the theory of electroweak interactions and other topics are discussed. A number of classical weak and electroweak processes are considered in details. This involves, first of all, the construction of the matrix elements of the process using both the Feynman diagram method (when perturbation theory can be applied) and the invariance principles (when perturbation theory fails). Then the cross sections and the decay probabilities are computed. The text is providing widely used computational techniques and some experimental data. (A.B.). 32 refs., 7 appendix

Investigation into fatigue crack growth and kinetic diagrams of fatigue failure

International Nuclear Information System (INIS)

Yarema, S.Ya.

1977-01-01

Studies on fatigue failure are discussed in terms of fatigue failure kinetic diagrams (FFKD), in which the fatigue crack growth rate is plotted against the stress intensity coefficient (SIC). The physical sense of the crack growth rate and SIC is discussed and their applicability for description of the material in the destruction zone, particularly in presence of various media. Variation of experimental parameters (loading and environment) is followed by a transition period during which the results of the experiment may depend on its history, so that FFKD would remain invariant. Advantages of tests under constant experimental conditions are shown. The ways to stabilize SIC are indicated and requirements to the samples are given. As an example, the tests of disc samples made of plate materials are given, where SIC does not depend on the crack length. The question of controlling the experimental conditions such as asymmetry and shape of the loading cycle, loading frequency, fluctuations of temperature and air composition is considered. The analytical functions describing FFKD are discussed. It is shown, that in appropriate dimensionless coordinates the FFKD of different materials merge into one curve

User testing of an adaptation of fishbone diagrams to depict results of systematic reviews

Directory of Open Access Journals (Sweden)

Gerald Gartlehner

2017-12-01

Full Text Available Abstract Background Summary of findings tables in systematic reviews are highly informative but require epidemiological training to be interpreted correctly. The usage of fishbone diagrams as graphical displays could offer researchers an effective approach to simplify content for readers with limited epidemiological training. In this paper we demonstrate how fishbone diagrams can be applied to systematic reviews and present the results of an initial user testing. Methods Findings from two systematic reviews were graphically depicted in the form of the fishbone diagram. To test the utility of fishbone diagrams compared with summary of findings tables, we developed and pilot-tested an online survey using Qualtrics. Respondents were randomized to the fishbone diagram or a summary of findings table presenting the same body of evidence. They answered questions in both open-ended and closed-answer formats; all responses were anonymous. Measures of interest focused on first and second impressions, the ability to find and interpret critical information, as well as user experience with both displays. We asked respondents about the perceived utility of fishbone diagrams compared to summary of findings tables. We analyzed quantitative data by conducting t-tests and comparing descriptive statistics. Results Based on real world systematic reviews, we provide two different fishbone diagrams to show how they might be used to display complex information in a clear and succinct manner. User testing on 77 students with basic epidemiological training revealed that participants preferred summary of findings tables over fishbone diagrams. Significantly more participants liked the summary of findings table than the fishbone diagram (71.8% vs. 44.8%; p < .01; significantly more participants found the fishbone diagram confusing (63.2% vs. 35.9%, p < .05 or indicated that it was difficult to find information (65.8% vs. 45%; p < .01. However, more than half

A New Diagnostic Diagram of Ionization Sources for High-redshift Emission Line Galaxies

Science.gov (United States)

Zhang, Kai; Hao, Lei

2018-04-01

We propose a new diagram, the kinematics–excitation (KEx) diagram, which uses the [O III] λ5007/Hβ line ratio and the [O III] λ5007 emission line width (σ [O III]) to diagnose the ionization source and physical properties of active galactic nuclei (AGNs) and star-forming galaxies (SFGs). The KEx diagram is a suitable tool to classify emission line galaxies at intermediate redshift because it uses only the [O III] λ5007 and Hβ emission lines. We use the main galaxy sample of SDSS DR7 and the Baldwin‑Phillips‑Terlevich (BPT) diagnostic to calibrate the diagram at low redshift. The diagram can be divided into three regions: the KEx-AGN region, which consists mainly of pure AGNs, the KEx-composite region, which is dominated by composite galaxies, and the KEx-SFG region, which contains mostly SFGs. LINERs strongly overlap with the composite and AGN regions. AGNs are separated from SFGs in this diagram mainly because they preferentially reside in luminous and massive galaxies and have higher [O III]/Hβ than SFGs. The separation between AGNs and SFGs is even cleaner thanks to the additional 0.15/0.12 dex offset in σ [O III] at fixed luminosity/stellar mass. We apply the KEx diagram to 7866 galaxies at 0.3 Survey, and compare it to an independent X-ray classification scheme using Chandra observations. X-ray AGNs are mostly located in the KEx-AGN region, while X-ray SFGs are mostly located in the KEx-SFG region. Almost all Type 1 AGNs lie in the KEx-AGN region. These tests support the reliability of this classification diagram for emission line galaxies at intermediate redshift. At z ∼ 2, the demarcation line between SFGs and AGNs is shifted by ∼0.3 dex toward higher values of σ [O III] due to evolution effects.

Metacomprehension judgements reflect the belief that diagrams improve learning from text.

Science.gov (United States)

Serra, Michael J; Dunlosky, John

2010-10-01

In two experiments we systematically explored whether people consider the format of text materials when judging their text learning, and whether doing so might inappropriately bias their judgements. Participants studied either text with diagrams (multimedia) or text alone and made both per-paragraph judgements and global judgements of their text learning. In Experiment 1 they judged their learning to be better for text with diagrams than for text alone. In that study, however, test performance was greater for multimedia, so the judgements may reflect either a belief in the power of multimedia or on-line processing. Experiment 2 replicated this finding and also included a third group that read texts with pictures that did not improve text performance. Judgements made by this group were just as high as those made by participants who received the effective multimedia format. These results confirm the hypothesis that people's metacomprehension judgements can be influenced by their beliefs about text format. Over-reliance on this multimedia heuristic, however, might reduce judgement accuracy in situations where it is invalid.

Phase Diagrams of Strongly Interacting Theories

DEFF Research Database (Denmark)

Sannino, Francesco

2010-01-01

We summarize the phase diagrams of SU, SO and Sp gauge theories as function of the number of flavors, colors, and matter representation as well as the ones of phenomenologically relevant chiral gauge theories such as the Bars-Yankielowicz and the generalized Georgi-Glashow models. We finally report...

Journeys on the H-R diagram

International Nuclear Information System (INIS)

Kaler, J.B.

1988-01-01

The evolution of various types of stars along the H-R diagram is discussed. Star birth and youth is addressed, and the events that occur due to core contraction, shell burning, and double-shell burning are described. The evolutionary courses of planetary nebulae, white dwarfs, and supernovas are examined

Multi-currency Influence Diagrams

DEFF Research Database (Denmark)

Nielsen, Søren Holbech; Nielsen, Thomas Dyhre; Jensen, Finn Verner

2004-01-01

Solution of decision problems, which involve utilities of several currencies, have traditionally required the problems to be converted into decision problems involving utilities of only one currency. This conversion are carried out using a tacit transformation, under the assumption...... that the converted problem is equivalent to the original one. In this paper we present an extension of the Influence Diagram framework, which allows for these decision problems to be modelled in their original form. We present an algorithm that, given a conversion function between the currencies, discovers...

Statistical HR diagrams for one hundred and fifteen thousand proper-motion stars

International Nuclear Information System (INIS)

Luyten, W.J.

1978-01-01

Since regular HR diagrams require apparent magnitudes, colors or spectra, and parallaxes, and such complete data are available for relatively few stars, there may be some advantage in making up diagrams which utilize proper motions instead of parallaxes, and are thus statistically similar to an HR diagram. The reduced proper motion, first used by Hertzsprung, is defined as H=m+5+5log μ, but may also be written as H=M+5log T, where T is the tangential velocity, and is expressed in astronomical units per year. A diagram plotting H against color will thus contain the considerable dispersion in tangential velocity which is a serious disadvantage. However, this is outweighed by two practical advantages. First, the one and the same person who does the proper motion survey can, and does also determine the other two quantities needed. Second, when using data obtained from such a proper motion survey one deals, statistically, with all the stars within a given distance and the results, therefore, are much more representative of the real situation in space than many HR diagrams which often contain an unrealistic preponderance of giants. (Auth.)

Query Processing for Probabilistic State Diagrams Describing Multiple Robot Navigation in an Indoor Environment

Energy Technology Data Exchange (ETDEWEB)

Czejdo, Bogdan [ORNL; Bhattacharya, Sambit [North Carolina Fayetteville State University; Ferragut, Erik M [ORNL

2012-01-01

This paper describes the syntax and semantics of multi-level state diagrams to support probabilistic behavior of cooperating robots. The techniques are presented to analyze these diagrams by querying combined robots behaviors. It is shown how to use state abstraction and transition abstraction to create, verify and process large probabilistic state diagrams.

Main principles of the Chernobyl' NPP zone development

International Nuclear Information System (INIS)

Ignatenko, E.I.; Komarov, V.I.; Zverkov, V.V.; Proskuryakov, A.G.

1989-01-01

It is suggested to divide the Chernobyl' NPP zone into two parts, which are the alienation and evacuation (buffer) zones. The alienation zone includes the areas with greatest contamination around the Chernobyl' NPP. The population residence in this zone is forbidden. The watching method of working with short-time personnel residence is suggested to be used in this zone. The buffer zone is the territory out of the alienation zone boundaries including all settlements, from which the population is evacuated. Constant residence is permitted in the buffer zone for persons 50 and more years old with introduction of restrictions for diet and residence organization. The production activity in this zone includes operation of three units of the Chernobyl' NPP, works with the Ukrytie object and researches. Operations connected with radioactive waste processing and redisposal from places of storage is not recommended to be done. It is suggested to develop methods for local radioactive waste processing

MARD—A moving average rose diagram application for the geosciences

Science.gov (United States)

Munro, Mark A.; Blenkinsop, Thomas G.

2012-12-01

MARD 1.0 is a computer program for generating smoothed rose diagrams by using a moving average, which is designed for use across the wide range of disciplines encompassed within the Earth Sciences. Available in MATLAB®, Microsoft® Excel and GNU Octave formats, the program is fully compatible with both Microsoft® Windows and Macintosh operating systems. Each version has been implemented in a user-friendly way that requires no prior experience in programming with the software. MARD conducts a moving average smoothing, a form of signal processing low-pass filter, upon the raw circular data according to a set of pre-defined conditions selected by the user. This form of signal processing filter smoothes the angular dataset, emphasising significant circular trends whilst reducing background noise. Customisable parameters include whether the data is uni- or bi-directional, the angular range (or aperture) over which the data is averaged, and whether an unweighted or weighted moving average is to be applied. In addition to the uni- and bi-directional options, the MATLAB® and Octave versions also possess a function for plotting 2-dimensional dips/pitches in a single, lower, hemisphere. The rose diagrams from each version are exportable as one of a selection of common graphical formats. Frequently employed statistical measures that determine the vector mean, mean resultant (or length), circular standard deviation and circular variance are also included. MARD's scope is demonstrated via its application to a variety of datasets within the Earth Sciences.

Constructing set-valued fundamental diagrams from jamiton solutions in second order traffic models

KAUST Repository

Seibold, Benjamin

2013-09-01

Fundamental diagrams of vehicular traiic ow are generally multivalued in the congested ow regime. We show that such set-valued fundamental diagrams can be constructed systematically from simple second order macroscopic traiic models, such as the classical Payne-Whitham model or the inhomogeneous Aw-Rascle-Zhang model. These second order models possess nonlinear traveling wave solutions, called jamitons, and the multi-valued parts in the fundamental diagram correspond precisely to jamiton-dominated solutions. This study shows that transitions from function-valued to set-valued parts in a fundamental diagram arise naturally in well-known second order models. As a particular consequence, these models intrinsically reproduce traiic phases. © American Institute of Mathematical Sciences.

Constructing set-valued fundamental diagrams from jamiton solutions in second order traffic models

KAUST Repository

Seibold, Benjamin; Flynn, Morris R.; Kasimov, Aslan R.; Rosales, Rodolfo Rubé n

2013-01-01

Fundamental diagrams of vehicular traiic ow are generally multivalued in the congested ow regime. We show that such set-valued fundamental diagrams can be constructed systematically from simple second order macroscopic traiic models, such as the classical Payne-Whitham model or the inhomogeneous Aw-Rascle-Zhang model. These second order models possess nonlinear traveling wave solutions, called jamitons, and the multi-valued parts in the fundamental diagram correspond precisely to jamiton-dominated solutions. This study shows that transitions from function-valued to set-valued parts in a fundamental diagram arise naturally in well-known second order models. As a particular consequence, these models intrinsically reproduce traiic phases. © American Institute of Mathematical Sciences.

Annihilation diagrams in two-body nonleptonic decays of charmed mesons

International Nuclear Information System (INIS)

Bedaque, P.; Das, A.; Mathur, V.S.

1994-06-01

In the pole-dominance model for the two-body nonleptonic decays of charmed mesons D → PV and D → VV, it is shown that the contributions of the intermediate pseudoscalar and the axial-vector meson poles cancel each other in the annihilation diagrams in the chiral limit. In the same limit, the annihilation diagrams for the D → PP decays vanish independently. (author). 6 refs, 3 figs

Towards Diagram Understanding: A Pilot Study Measuring Cognitive Workload Through Eye-Tracking

DEFF Research Database (Denmark)

Maier, Anja; Baltsen, Nick; Christoffersen, Henrik

2014-01-01

We investigate model understanding, in particular , how the quality of the UML diagram layout impacts cognitive load. We hypothesize that this w ill have a significant impact on the structure and effectiveness of engineers’ communication. In previous work, we have studied task performance...... measurements and subjective assessments; here, we also investigate behavioral indicators such as fixation and pupillary dilation. We use such indicators to explore diagram understanding- and reading strategies and how such strategies are impacted, e.g. by diagram type and expertise level. In the pilot eye...

Bosonic Loop Diagrams as Perturbative Solutions of the Classical Field Equations in φ4-Theory

International Nuclear Information System (INIS)

Finster, Felix; Tolksdorf, Juergen

2012-01-01

Solutions of the classical φ 4 -theory in Minkowski space-time are analyzed in a perturbation expansion in the nonlinearity. Using the language of Feynman diagrams, the solution of the Cauchy problem is expressed in terms of tree diagrams which involve the retarded Green's function and have one outgoing leg. In order to obtain general tree diagrams, we set up a ''classical measurement process'' in which a virtual observer of a scattering experiment modifies the field and detects suitable energy differences. By adding a classical stochastic background field, we even obtain all loop diagrams. The expansions are compared with the standard Feynman diagrams of the corresponding quantum field theory.

Bosonic Loop Diagrams as Perturbative Solutions of the Classical Field Equations in ϕ4-Theory

Science.gov (United States)

Finster, Felix; Tolksdorf, Jürgen

2012-05-01

Solutions of the classical ϕ4-theory in Minkowski space-time are analyzed in a perturbation expansion in the nonlinearity. Using the language of Feynman diagrams, the solution of the Cauchy problem is expressed in terms of tree diagrams which involve the retarded Green's function and have one outgoing leg. In order to obtain general tree diagrams, we set up a "classical measurement process" in which a virtual observer of a scattering experiment modifies the field and detects suitable energy differences. By adding a classical stochastic background field, we even obtain all loop diagrams. The expansions are compared with the standard Feynman diagrams of the corresponding quantum field theory.

Diagramming Scientific Papers - A New Idea for Understanding/Teaching/Sharing Science

Science.gov (United States)

Saltus, R. W.; Fedi, M.

2014-12-01

How do we best communicate scientific results? As the number of scientists and scientific papers steadily increases, one of the greatest challenges is effective and efficient sharing of science. The official repository of scientific knowledge is the peer-reviewed journal archive. However, this primary knowledge can be difficult to access and understand by anyone but a relevant specialist. We propose some new ideas for diagramming the content and significance of scientific papers using a simple and intuitive graphical approach. We propose a visual mapping that highlights four fundamental aspects of most scientific papers: Data, Methods/Models, Results/Ideas, and Implications/Importance. Each of these aspects is illustrated within boxed fields which contain one or more labeled elements positioned to reflect novelty (aka originality) and impact relative to the vertical and horizontal axes. The relative position of the boxed fields themselves indicates the relative significance of data, methods, ideas, or implications to the paper. Optional lines between boxed elements indicate the flow and dependence of data/methods/ideas within the paper. As with any graphical depiction, you need to see it to best appreciate it -- this written abstract is only meant as an introduction to the idea.We anticipate that diagramming may prove useful in both communication of scientific ideas among scientists as well as in education and outreach. For example, professors could assign diagramming of papers as a way to help students organize their thoughts about the structure and impact of scientific articles. Students could compare and defend their diagrams as a way to facilitate discussion/debate. Authors could diagram their own work as a way to efficiently summarize the importance and significance of their work. We also imagine that (in the future) automatic diagramming might be used to help summarize or facilitate the discovery of archived work.

Using a Ternary Diagram to Display a System's Evolving Energy Distribution

Science.gov (United States)

Brazzle, Bob; Tapp, Anne

2016-01-01

A ternary diagram is a graphical representation used for systems with three components. They are familiar to mineralogists (who typically use them to categorize varieties of solid solution minerals such as feldspar) but are not yet widely used in the physics community. Last year the lead author began using ternary diagrams in his introductory…

Students' Ability to Solve Process-Diagram Problems in Secondary Biology Education

Science.gov (United States)

Kragten, Marco; Admiraal, Wilfried; Rijlaarsdam, Gert

2015-01-01

Process diagrams are important tools in biology for explaining processes such as protein synthesis, compound cycles and the like. The aim of the present study was to measure the ability to solve process-diagram problems in biology and its relationship with prior knowledge, spatial ability and working memory. For this purpose, we developed a test…

Some Consequences of Prompting Novice Physics Students to Construct Force Diagrams

Science.gov (United States)

Heckler, Andrew F.

2010-01-01

We conducted a series of experiments to investigate the extent to which prompting the construction of a force diagram affects student solutions to simple mechanics problems. A total of 891 university introductory physics students were given typical force and motion problems under one of the two conditions: when a force diagram was or was not…

Multicritical phase diagrams of the ferromagnetic spin-3/2 Blume-Emery-Griffiths model with repulsive biquadratic coupling including metastable phases: The cluster variation method and the path probability method with the point distribution

Energy Technology Data Exchange (ETDEWEB)

Keskin, Mustafa [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)], E-mail: keskin@erciyes.edu.tr; Canko, Osman [Department of Physics, Erciyes University, 38039 Kayseri (Turkey)

2008-01-15

We study the thermal variations of the ferromagnetic spin-3/2 Blume-Emery-Griffiths (BEG) model with repulsive biquadratic coupling by using the lowest approximation of the cluster variation method (LACVM) in the absence and presence of the external magnetic field. We obtain metastable and unstable branches of the order parameters besides the stable branches and phase transitions of these branches are investigated extensively. The classification of the stable, metastable and unstable states is made by comparing the free energy values of these states. We also study the dynamics of the model by using the path probability method (PPM) with the point distribution in order to make sure that we find and define the metastable and unstable branches of the order parameters completely and correctly. We present the metastable phase diagrams in addition to the equilibrium phase diagrams in the (kT/J, K/J) and (kT/J, D/J) planes. It is found that the metastable phase diagrams always exist at the low temperatures, which are consistent with experimental and theoretical works.

Multicritical phase diagrams of the ferromagnetic spin-3/2 Blume-Emery-Griffiths model with repulsive biquadratic coupling including metastable phases: The cluster variation method and the path probability method with the point distribution

International Nuclear Information System (INIS)

Keskin, Mustafa; Canko, Osman

2008-01-01

We study the thermal variations of the ferromagnetic spin-3/2 Blume-Emery-Griffiths (BEG) model with repulsive biquadratic coupling by using the lowest approximation of the cluster variation method (LACVM) in the absence and presence of the external magnetic field. We obtain metastable and unstable branches of the order parameters besides the stable branches and phase transitions of these branches are investigated extensively. The classification of the stable, metastable and unstable states is made by comparing the free energy values of these states. We also study the dynamics of the model by using the path probability method (PPM) with the point distribution in order to make sure that we find and define the metastable and unstable branches of the order parameters completely and correctly. We present the metastable phase diagrams in addition to the equilibrium phase diagrams in the (kT/J, K/J) and (kT/J, D/J) planes. It is found that the metastable phase diagrams always exist at the low temperatures, which are consistent with experimental and theoretical works

ASTEROSEISMIC DIAGRAMS FROM A SURVEY OF SOLAR-LIKE OSCILLATIONS WITH KEPLER

Energy Technology Data Exchange (ETDEWEB)

White, Timothy R.; Bedding, Timothy R.; Stello, Dennis; Benomar, Othman; Huber, Daniel [Sydney Institute for Astronomy (SIfA), School of Physics, University of Sydney, NSW 2006 (Australia); Appourchaux, Thierry; Gaulme, Patrick [Institut d' Astrophysique Spatiale, UMR8617, Universite Paris XI, Batiment 121, 91405 Orsay Cedex (France); Ballot, Jerome [Institut de Recherche en Astrophysique et Planetologie, CNRS, 14 avenue E. Belin, 31400 Toulouse (France); Bonanno, Alfio; Corsaro, Enrico [INAF Observatorio Astrofisico di Catania, Via S. Sofia 78, 95123 Catania (Italy); Broomhall, Anne-Marie; Chaplin, William J.; Elsworth, Yvonne P.; Hekker, Saskia [School of Physics and Astronomy, University of Birmingham, Birmingham B15 2TT (United Kingdom); Campante, Tiago L. [Centro de Astrofisica and Faculdade de Ciencias, Universidade do Porto, Rua das Estrelas, 4150-762 Porto (Portugal); Christensen-Dalsgaard, Jorgen; Dogan, Guelnur; Handberg, Rasmus [Danish AsteroSeismology Centre (DASC), Department of Physics and Astronomy, Aarhus University, DK-8000 Aarhus C (Denmark); Fletcher, Stephen T. [Materials Engineering Research Institute, Faculty of Arts, Computing, Engineering and Sciences, Sheffield Hallam University, Sheffield, S1 1WB (United Kingdom); Garcia, Rafael A., E-mail: t.white@physics.usyd.edu.au [Laboratoire AIM, CEA/DSM-CNRS, Universite Paris 7 Diderot, IRFU/SAp, Centre de Saclay, 91191 Gif-sur-Yvette (France); and others

2011-11-20

Photometric observations made by the NASA Kepler Mission have led to a dramatic increase in the number of main-sequence and subgiant stars with detected solar-like oscillations. We present an ensemble asteroseismic analysis of 76 solar-type stars. Using frequencies determined from the Kepler time-series photometry, we have measured three asteroseismic parameters that characterize the oscillations: the large frequency separation ({Delta}{nu}), the small frequency separation between modes of l = 0 and l = 2 ({delta}{nu}{sub 02}), and the dimensionless offset ({epsilon}). These measurements allow us to construct asteroseismic diagrams, namely the so-called Christensen-Dalsgaard diagram of {delta}{nu}{sub 02} versus {Delta}{nu}, and the recently re-introduced {epsilon} diagram. We compare the Kepler results with previously observed solar-type stars and with theoretical models. The positions of stars in these diagrams places constraints on their masses and ages. Additionally, we confirm the observational relationship between {epsilon} and T{sub eff} that allows for the unambiguous determination of radial order and should help resolve the problem of mode identification in F stars.

On some limitations of reaction-diffusion chemical computers in relation to Voronoi diagram and its inversion

International Nuclear Information System (INIS)

Adamatzky, Andrew; Lacy Costello, Benjamin de

2003-01-01

A reaction-diffusion chemical computer in this context is a planar uniform chemical reactor, where data and results of a computation are represented by concentration profiles of reactants and the computation itself is implemented via the spreading and interaction of diffusive and phase waves. This class of chemical computers are efficient at solving problems with a 'natural' parallelism where data sets are decomposable onto a large number of geographically neighboring domains which are then processed in parallel. Typical problems of this type include image processing, geometrical transformations and optimisation. When chemical based devices are used to solve such problems questions regarding their reproducible, efficiency and the accuracy of their computations arise. In addition to these questions what are the limitations of reaction-diffusion chemical processors--what type of problems cannot currently and are unlikely ever to be solved? To answer the questions we study how a Voronoi diagram is constructed and how it is inverted in a planar chemical processor. We demonstrate that a Voronoi diagram is computed only partially in the chemical processor. We also prove that given a specific Voronoi diagram it is impossible to reconstruct the planar set (from which diagram was computed) in the reaction-diffusion chemical processor. In the Letter we open the first ever line of enquiry into the computational inability of reaction-diffusion chemical computers

Ammonia-water phase diagram and its implications for icy satellites

International Nuclear Information System (INIS)

Johnson, M.L.; Nicol, M.

1986-01-01

A Holzapfel-type diamond anvil cell is used to determine the NH 3 - H 2 O phase diagram in the region from 0 to 33 mole percent NH 3 , 240 to 370 K, and 0 to 5 GPa. The following phases were identified: liquid; water ices Ih, III, V, VI, VII, and VIII; ammonia monohydrate, NH 3 .H 2 O; and ammonia dihydrate NH 3 . 2 H 2 O. Ammonia dihydrate becomes prominent at moderate pressures (less than 1 GPa), with planetologically significant implications, including the possibility of layering in Titan's magma ocean

Development and Application of a Rubric for Analysis of Novice Students' Laboratory Flow Diagrams

Science.gov (United States)

Davidowitz, Bette; Rollnick, Marissa; Fakudze, Cynthia

2005-01-01

The purpose of this study was to develop and apply a scheme for the analysis of flow diagrams. The flow diagrams in question are a schematic representation of written instructions that require students to process the text of their practical manual. It was hoped that an analysis of the flow diagrams would provide insight into students'…

Massive 3-loop ladder diagrams for quarkonic local operator matrix elements

International Nuclear Information System (INIS)

Ablinger, Jakob; Blümlein, Johannes; Hasselhuhn, Alexander; Klein, Sebastian; Schneider, Carsten; Wißbrock, Fabian

2012-01-01

3-loop diagrams of the ladder-type, which emerge for local quarkonic twist-2 operator matrix elements, are computed directly for general values of the Mellin variable N using Appell-function representations and applying modern summation technologies provided by the package Sigma and the method of hyperlogarithms. In some of the diagrams generalized harmonic sums with ξ∈{1,1/2,2} emerge beyond the usual nested harmonic sums. As the asymptotic representation of the corresponding integrals shows, the generalized sums conspire giving well behaved expressions for large values of N. These diagrams contribute to the 3-loop heavy flavor Wilson coefficients of the structure functions in deep-inelastic scattering in the region Q 2 ≫m 2 .

Visual syntax of UML class and package diagram constructs as an ontology

CSIR Research Space (South Africa)

Thomas, A

2015-11-01

Full Text Available and package diagrams are two diagrams of UML. The motivation for this work is twofold; UML lacks a formal visual syntax specification and ontologies are under-explored for visual syntax specifications. The work in this paper, therefore, explores using...

Na-Si binary phase diagram and solution growth of silicon crystals

International Nuclear Information System (INIS)

Morito, H.; Yamada, T.; Ikeda, T.; Yamane, H.

2009-01-01

In the present study, a Na-Si binary phase diagram was first presented from the results of differential thermal analysis and X-ray diffraction. Based on the phase diagram, we performed low-temperature formation of single crystals, film and porous bulk of Si by vaporizing Na from a Na-Si melt at 800 or 900 deg. C.

Study of equilibrium phase diagrams of the system In-As-Pb

International Nuclear Information System (INIS)

Baranov, A.N.; Gorelenok, A.A.; Litvak, A.M.; Sherstnev, V.V.; Yakovlev, Yu.P.

1992-01-01

Experimental data on fusibility diagram of In-As-Pb system are presented. Model calculation of fusibility diagram of this system and corresponding binary subsystems, using EF LCP method was conducted. Preliminary studies demonstrate the possibility of changing type of eigendefect in InAs, when growing from arsenous carbon. This becomes posible when using lead as neutral solvent

On Hardy's paradox, weak measurements, and multitasking diagrams

Energy Technology Data Exchange (ETDEWEB)

Meglicki, Zdzislaw, E-mail: gustav@indiana.edu [Indiana University, Office of the Vice President for Information Technology, 601 E. Kirkwood Ave., Room 116, Bloomington, IN 47405-1223 (United States)

2011-07-04

We discuss Hardy's paradox and weak measurements by using multitasking diagrams, which are introduced to illustrate the progress of quantum probabilities through the double interferometer system. We explain how Hardy's paradox is avoided and elaborate on the outcome of weak measurements in this context. -- Highlights: → Hardy's paradox explained and eliminated. → Weak measurements: what is really measured? → Multitasking diagrams: introduced and used to discuss quantum mechanical processes.

Partition functions of web diagrams with an O7{sup −}-plane

Energy Technology Data Exchange (ETDEWEB)

Hayashi, Hirotaka [Tokai University, 4-1-1 Kitakaname,Hiratsuka, Kanagawa 259-1292 (Japan); Departamento de Física Teórica and Instituto de Física Teórica UAM/CSIC,Universidad Autónoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Zoccarato, Gianluca [Departamento de Física Teórica and Instituto de Física Teórica UAM/CSIC,Universidad Autónoma de Madrid, Cantoblanco, 28049 Madrid (Spain)

2017-03-22

We consider the computation of the topological string partition function for 5-brane web diagrams with an O7{sup −}-plane. Since upon quantum resolution of the orientifold plane these diagrams become non-toric web diagrams without the orientifold we are able to apply the topological vertex to obtain the Nekrasov partition function of the corresponding 5d theory. We apply this procedure to the case of 5d SU(N) theories with one hypermultiplet in the antisymmetric representation and to the case of 5d pure USp(2N) theories. For these cases we discuss the dictionary between parameters and moduli of the 5d gauge theory and lengths of 5-branes in the web diagram and moreover we perform comparison of the results obtained via application of the topological vertex and the one obtained via localisation techniques, finding in all instances we consider perfect agreement.

SPECIALIZED MAPPING OF CRUSTAL FAULT ZONES. PART 1: BASIC THEORETICAL CONCEPTS AND PRINCIPLES

Directory of Open Access Journals (Sweden)

K. Zh. Seminsky

2014-01-01

Full Text Available Long-term studies of shear zones have included collection of data on fractures showing no indication of displacement which are termed as 'blank' fractures. A method aimed at mapping fault structures and stress fields has been developed on the basis of results of paragenetic analysis of measurements of abundant fractures. The method is termed as 'specialized mapping', firstly, due to its specific structural goal so that to distinguish it from the conventional geological mapping of regions in nature, and, secondly, because of the specific procedure applied to refer to fractures as references to decipher fault-block patterns of natural regions. In Part 1, basic theoretical concepts and principles of specialized mapping are described. Part 2 is being prepared for publication in one of the next issues of the journal; it will cover stages of the proposed method and describe some of the cases of its application.In terms of general organizational principles, specialized mapping is similar to other methods based on structural paragenetic analysis and differs from such methods in types of paragenesises viewed as references to reveal crustal fault zones. Such paragenesises result from stage-by-stage faulting (Fig 2 and Fig. 7 during which stress fields of the 2nd order are regularly changeable within the shear zone. According to combined experimental and natural data, a complete paragenesis of fractures in the shear zone includes a major (1st order fault plane and fractures of other seven types, R, R’, n, n’, t, t’ and T (2nd order (Fig. 4 and Fig 8. At the fracture level, each of them corresponds to a paragenesis including three nearly perpendicular systems of early ruptures (Fig. 1, which are based on two classical patterns of conjugated fractures, one of which is consistent with the position of the fault plane (Fig. 3. Taking into account that strike-slip, reverse and normal faults are similar in terms of mechanics (i.e. they are formed due to

Project of computer program for designing the steel with the assumed CCT diagram

OpenAIRE

S. Malara; J. Trzaska; L.A. Dobrzański

2007-01-01

Purpose: The aim of this paper was developing a project of computer aided method for designing the chemicalcomposition of steel with the assumed CCT diagram.Design/methodology/approach: The purpose has been achieved in four stages. At the first stage characteristicpoints of CCT diagram have been determined. At the second stage neural networks have been developed, andnext CCT diagram terms of similarity have been worked out- at the third one. In the last one steel chemicalcomposition optimizat...

Phase diagrams of laser-processed nanoparticles of brass

Energy Technology Data Exchange (ETDEWEB)

Kazakevich, P.V. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences 38, Vavilov Street, 119991 Moscow (Russian Federation); Simakin, A.V. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences 38, Vavilov Street, 119991 Moscow (Russian Federation); Shafeev, G.A. [Wave Research Center of A.M. Prokhorov General Physics Institute of the Russian Academy of Sciences 38, Vavilov Street, 119991 Moscow (Russian Federation); Monteverde, F. [Electron Microscopy Unit, Materia Nova, Avenue Copernic 1, B-7000 Mons (Belgium); Wautelet, M. [Condensed Matter Physics, University of Mons-Hainaut, 23, Avenue Maistriau, B-7000 Mons (Belgium)]. E-mail: michel.wautelet@umh.ac.be

2007-07-31

Nanoparticles of brass are prepared by ablation of a brass target in ethanol using radiation of a copper-vapor laser at various laser fluences. The nanoparticles are characterized by TEM and optical spectroscopy. The multipulse laser irradiation leads to formation both the nanoparticles in liquid and well-ordered micro-structures on a surface of a target. It is revealed that both the morphology and absorption spectra of brass nanoparticles depend on presence of the micro-structures. Nanoparticles with the various phase diagrams are formed from a flat brass surface and from the same surface with micro-structures. The results are compared with a model of phase diagrams, in which size and composition effects are taken into account.

Finding and accessing diagrams in biomedical publications.

Science.gov (United States)

Kuhn, Tobias; Luong, ThaiBinh; Krauthammer, Michael

2012-01-01

Complex relationships in biomedical publications are often communicated by diagrams such as bar and line charts, which are a very effective way of summarizing and communicating multi-faceted data sets. Given the ever-increasing amount of published data, we argue that the precise retrieval of such diagrams is of great value for answering specific and otherwise hard-to-meet information needs. To this end, we demonstrate the use of advanced image processing and classification for identifying bar and line charts by the shape and relative location of the different image elements that make up the charts. With recall and precisions of close to 90% for the detection of relevant figures, we discuss the use of this technology in an existing biomedical image search engine, and outline how it enables new forms of literature queries over biomedical relationships that are represented in these charts.

Prevention of Backover Fatalities in Highway Work Zones: A Synthesis of Current Practices and Recommendations

Directory of Open Access Journals (Sweden)

Wei Fan

2014-12-01

Full Text Available The purpose of this paper is to synthesize current practices and procedures on the prevention of backing fatalities in highway work zones. First, general work zone safety hazards are reviewed, particularly blind areas are identified. Second, engineering controls currently in use are examined and explained to help understand what steps can be taken to prevent future backing fatalities. Third, administrative controls (including signalers, drivers, and workers-on-foot training are also discussed. Fourth, existing technology controls are reviewed for use in aiding equipment operators in identifying when pedestrian personnel are in dangerous areas around their equipment (i.e., back-up camera, radar. Fifth, recommendations are made based on the comprehensive review of the backover fatality prevention techniques in construction work zones and the conducted testing results of several commercially available systems. Recommendations on engineering and technology controls are discussed, with detailed information such as improving internal traffic control plans, and integrating technology with traffic control plans. Information and drawings are provided to illustrate how to design work zones, and the internal traffic flow diagrams are created using the integrated technology available, and site specific characteristics. The drawings represent examples of using different types of technology, in different scenarios using the proper legend, as well as using the proper general and technology notes to help explain the traffic control plan, ensuring that full comprehension is made. Recommendations on administrative controls are also given such as how to conduct safety meetings, electing safety officers, how to set regulations and guidelines for workers, and how to handle training. Training should be used as a backover fatality prevention method for pedestrian workers, flaggers, spotters, and equipment operators. Finally, a summary and discussion of future research

Coastal zone

International Nuclear Information System (INIS)

2002-01-01

The report entitled Climate Change Impacts and Adaptation : A Canadian Perspective, presents a summary of research regarding the impacts of climate change on key sectors over the past five years as it relates to Canada. This chapter on the coastal zone focuses on the impact of climate change on Canada's marine and Great Lakes coasts with tips on how to deal with the impacts associated with climate change in sensitive environments. This report is aimed at the sectors that will be most affected by adaptation decisions in the coastal zone, including fisheries, tourism, transportation and water resources. The impact of climate change in the coastal zone may include changes in water levels, wave patterns, storm surges, and thickness of seasonal ice cover. The Intergovernmental Panel on Climate Change projects global average sea level will rise between 9 and 88 centimetres between 1990 to 2100, but not all areas of Canada will experience the same rate of future sea level change. The main physical impact would be shoreline change that could result in a range of biophysical and socio-economic impacts, some beneficial, some negative. The report focuses on issues related to infrastructure and communities in coastal regions. It is noted that appropriate human adaptation will play a vital role in reducing the extent of potential impacts by decreasing the vulnerability of average zone to climate change. The 3 main trends in coastal adaptation include: (1) increase in soft protection, retreat and accommodation, (2) reliance on technology such as geographic information systems to manage information, and (3) awareness of the need for coastal adaptation that is appropriate for local conditions. 61 refs., 7 figs

Slip Zone versus Damage Zone Micromechanics, Arima-Takasuki Tectonic Line, Japan

Science.gov (United States)

White, J. C.; Lin, A.

2017-12-01

The Arima-Takasuki Tectonic Line (ATTL) of southern Honshu, Japan is defined by historically active faults and multiple splays producing M7 earthquakes. The damage zone of the ATTL comprises a broad zone of crushed, comminuted and pulverized granite/rhyolite1,2containing cm-scale slip zones and highly comminuted injection veins. In this presentation, prior work on the ATTL fault rocks is extending to include microstructural characterization by transmission electron microscopy (TEM) from recent trenching of the primary slip zone, as well as secondary slip zones. This is necessary to adequately characterize the extremely fine-grained material (typically less than 1mm) in both damage and core zones. Damage zone material exhibits generally random textures3 whereas slip zones are macroscopically foliated, and compositionally layered, notwithstanding a fairly homogeneous protolith. The latter reflects fluid-rock interaction during both coseismic and interseismic periods. The slip zones are microstructurally heterogeneous at all scales, comprising not only cataclasites and phyllosilicate (clay)-rich gouge zones, but Fe/Mn pellets or clasts that are contained within gouge. These structures appear to have rolled and would suggest rapid recrystallization and/or growth. A central question related to earthquake recurrence along existing faults is the nature of the gouge. In both near-surface exposures and ongoing drilling at depth, "plastic" or "viscous" gouge zones comprise ultra-fine-grained clay-siliciclastic particles that would not necessarily respond in a simple frictional manner. Depending on whether the plastic nature of these slip zones develops during or after slip, subsequent focusing of slip within them could be complicated. 1 Mitchell, T.A., Ben-Zion, Y., Shimamoto, T., 2011. Ear. Planet. Sci. Lett. 308, 284-297. 2 Lin, A., Yamashita, K, Tanaka, M. J., 2013. Struc. Geol. 48, 3-13. 3 White, J.C., Lin, A. 2016. Proc. AGU Fall Mtg., T42-02 San Francisco.

The phase diagram of KNO3-KClO3

International Nuclear Information System (INIS)

Zhang Xuejun; Tian Jun; Xu Kangcheng; Gao Yici

2004-01-01

The binary phase diagram of KNO 3 -KClO 3 is studied by means of differential scanning calorimetry (DSC) and high-temperature X-ray diffraction. The limited solid solutions, K(NO 3 ) 1-x (ClO 3 ) x (0 3 ) 1-x (ClO 3 ) x (0.90 3 -based solid solutions and KClO 3 -based solid solutions phase, respectively. For KNO 3 -based solid solutions, KNO 3 ferroelectric phase can be stable from 423 to 223 K as a result of substituting of NO 3 by ClO 3 -radicals. The temperatures for solidus and liquidus have been determined based on limited solid solutions. Two models, Henrian solution and regular solution theory for KNO 3 -based (α) phase and KClO 3 -based (β) phase, respectively, are employed to reproduce solidus and liquidus of the phase diagram. The results are in good agreement with the DSC data. The thermodynamic properties for α and β solid solutions have been derived from an optimization procedure using the experimental data. The calculated phase diagram and optimized thermodynamic parameters are thermodynamically self-consistent

Phase diagrams of superconducting materials: Metallurgy, fabrication, and applications

International Nuclear Information System (INIS)

Flukiger, R.

1981-01-01

Because a large number of investigations on superconducting material have been made on insufficiently characterized samples, and with temperature phase diagrams which contained serious errors, phase diagrams are studied. It is seen that the variation of critical temperature as a function of chemical composition for a given compound can be used as a supplementary tool in determining composition with greater accuracy. The consequent search for higher critical temperature value in specified materials has led to a new concept in determining high temperature phase diagrams. Most of this paper is devoted to the study of bulk binary, pseudobinary, or ternary superconductors at their equilibrium state. As will be shown in several cases, these data serve as standard values and are of great help in understanding the superconducting behavior in materials produced by non-equilibrium methods, i.e., splat-cooling, thin film preparation by either sputtering, co-evaporation, or CVD, and diffusion processes in multifilamentary composite wires. An example for the departure from thermal equilibrium is the retention of metastable composition by a fast quenching rate

Application Of Empirical Phase Diagrams For Multidimensional Data Visualization Of High Throughput Microbatch Crystallization Experiments.

Science.gov (United States)

Klijn, Marieke E; Hubbuch, Jürgen

2018-04-27

Protein phase diagrams are a tool to investigate cause and consequence of solution conditions on protein phase behavior. The effects are scored according to aggregation morphologies such as crystals or amorphous precipitates. Solution conditions affect morphological features, such as crystal size, as well as kinetic features, such as crystal growth time. Common used data visualization techniques include individual line graphs or symbols-based phase diagrams. These techniques have limitations in terms of handling large datasets, comprehensiveness or completeness. To eliminate these limitations, morphological and kinetic features obtained from crystallization images generated with high throughput microbatch experiments have been visualized with radar charts in combination with the empirical phase diagram (EPD) method. Morphological features (crystal size, shape, and number, as well as precipitate size) and kinetic features (crystal and precipitate onset and growth time) are extracted for 768 solutions with varying chicken egg white lysozyme concentration, salt type, ionic strength and pH. Image-based aggregation morphology and kinetic features were compiled into a single and easily interpretable figure, thereby showing that the EPD method can support high throughput crystallization experiments in its data amount as well as its data complexity. Copyright © 2018. Published by Elsevier Inc.

Electrodynamic metaphors: communicating particle physics with Feynman diagrams

Directory of Open Access Journals (Sweden)

Pietroni Massimo

2002-03-01

Full Text Available The aim of this project is to communicate the basic laws of particle physics with Feynman diagrams - visual tools which represent elementary particle processes. They were originally developed as a code to be used by physicists and are still used today for calculations and elaborations of theoretical nature. The technical and mathematical rules of Feynman diagrams are obviously the exclusive concern of physicists, but on a pictorial level they can help to popularize many concepts, ranging from matter and the antimatter; the creation, destruction and transformation of particles; the role of ‘virtual’ particles in interactions; the conservation laws, symmetries, etc. Unlike the metaphors often used to describe the microcosm, these graphic representations provide an unequivocal translation of the physical content of the underlying quantum theory. As such they are perfect metaphors, not misleading constructions. A brief introduction on Feynman diagrams will be followed by the practical realization of this project, which will be carried out with the help of an experiment based on three-dimensional manipulable objects. The Feynman rules are expressed in terms of mechanical constraints on the possible conjuctions among the various elements of the experiment. The final part of the project will present the results of this experiment, which has been conducted among high-school students.

A study on the influence diagrams for the application to containment performance analysis

International Nuclear Information System (INIS)

Park, Joon Won

1995-02-01

Influence diagrams have been applied to containment performance analysis of Young-Gwang 3 and 4 in an effort to explicitly display the dependencies between events and to treat operator intervention more generally. This study has been initiated to remove the three major drawbacks of the current event tree methodology: 1) Event tree cannot express dependency between events explicitly. 2) Accident Progression Event Tree (APET) cannot represent entire containment system. 3) It is difficult to consider operator intervention with event tree. To resolve these problems, a new approach, i.e., influence diagrams, are proposed. In the present work, the applicability of the influence diagrams have been demonstrated to YGN 3 and 4 containment performance analysis and an assessment of accident management strategies. To show that the results of the application of influence diagrams are reasonable, results are compared with that of YGN 3 and 4 IPE. Both results are in good agreement. In addition, influence diagrams are used to assess two accident management strategies: 1) RCS depressurization, 2) cavity flooding. Cavity flooding has a favorable effect to late containment failure and basemat melt-through, and depressurization of RCS is good for steam generator tube rupture. However, early containment failure probability is worse in both cases. As a result of the present study, it is shown that influence diagrams can be applied to the containment performance analysis

The Use of the Skew T, Log P Diagram in Analysis and Forecasting. Revision

Science.gov (United States)

1990-03-01

28 x 30 been added to further enhance the value of the inches. This version now includes the Apple - diagram. A detailed description of the Skew T, man...airocrau rqor we ovailable. The eauning lIkIaatte U the lop rate Is. at times. recorded as swot - adobaik wheun the mulm leave* a cloud Up and ener

Characteristic Dynkin diagrams and W algebras

International Nuclear Information System (INIS)

Ragoucy, E.

1993-01-01

We present a classification of characteristic Dynkin diagrams for the A N , B N , C N and D N algebras. This classification is related to the classification of W(G, K) algebras arising from non-abelian Toda models, and we argue that it can give new insight on the structure of W algebras. (orig.)

Students Mental Representation of Biology Diagrams/Pictures Conventions Based on Formation of Causal Network

Science.gov (United States)

Sampurno, A. W.; Rahmat, A.; Diana, S.

2017-09-01

Diagrams/pictures conventions is one form of visual media that often used to assist students in understanding the biological concepts. The effectiveness of use diagrams/pictures in biology learning at school level has also been mostly reported. This study examines the ability of high school students in reading diagrams/pictures biological convention which is described by Mental Representation based on formation of causal networks. The study involved 30 students 11th grade MIA senior high school Banten Indonesia who are studying the excretory system. MR data obtained by Instrument worksheet, developed based on CNET-protocol, in which there are diagrams/drawings of nephron structure and urinary mechanism. Three patterns formed MR, namely Markov chain, feedback control with a single measurement, and repeated feedback control with multiple measurement. The third pattern is the most dominating pattern, differences in the pattern of MR reveal the difference in how and from which point the students begin to uncover important information contained in the diagram to establish a causal networks. Further analysis shows that a difference in the pattern of MR relate to how complex the students process the information contained in the diagrams/pictures.

Approximation of hadron interactions by Regge diagrams with multipomeron exchange

International Nuclear Information System (INIS)

Barashenkov, V.S.

1988-01-01

A good agreement of hadron diffraction interaction total cross section and their elastic scattering at small angles calculated by summarizing Regge multipomeron exchange diagrams with experiment mentioned by a number of authors results from the fitting of a great variety of the parameters contained in the formulas. The agreement of the other hadron characteristcs with experiment is worse. Distribution of hadron interactions over the number of fragmenting quark-gluon strings calculated by utilizing Regge diagrams is discussed

Exact ground-state phase diagrams for the spin-3/2 Blume-Emery-Griffiths model

Energy Technology Data Exchange (ETDEWEB)

Canko, Osman; Keskin, Mustafa [Department of Physics, Erciyes University, 38039 Kayseri (Turkey); Deviren, Bayram [Institute of Science, Erciyes University, 38039 Kayseri (Turkey)], E-mail: keskin@erciyes.edu.tr

2008-05-15

We have calculated the exact ground-state phase diagrams of the spin-3/2 Ising model using the method that was proposed and applied to the spin-1 Ising model by Dublenych (2005 Phys. Rev. B 71 012411). The calculated, exact ground-state phase diagrams on the diatomic and triangular lattices with the nearest-neighbor (NN) interaction have been presented in this paper. We have obtained seven and 15 topologically different ground-state phase diagrams for J>0 and J<0, respectively, on the diatomic lattice and have found the conditions for the existence of uniform and intermediate or non-uniform phases. We have also constructed the exact ground-state phase diagrams of the model on the triangular lattice and found 20 and 59 fundamental phase diagrams for J>0 and J<0, respectively, the conditions for the existence of uniform and intermediate phases have also been found.

Phase Diagram of Spiking Neural Networks

Directory of Open Access Journals (Sweden)

Hamed eSeyed-Allaei

2015-03-01

Full Text Available In computer simulations of spiking neural networks, often it is assumed that every two neurons of the network are connected by a probablilty of 2%, 20% of neurons are inhibitory and 80% are excitatory. These common values are based on experiments, observations. but here, I take a different perspective, inspired by evolution. I simulate many networks, each with a different set of parameters, and then I try to figure out what makes the common values desirable by nature. Networks which are configured according to the common values, have the best dynamic range in response to an impulse and their dynamic range is more robust in respect to synaptic weights. In fact, evolution has favored networks of best dynamic range. I present a phase diagram that shows the dynamic ranges of different networks of different parameteres. This phase diagram gives an insight into the space of parameters -- excitatory to inhibitory ratio, sparseness of connections and synaptic weights. It may serve as a guideline to decide about the values of parameters in a simulation of spiking neural network.

Magnetic phase diagrams of UNiGe

International Nuclear Information System (INIS)

Nakotte, H.; Hagmusa, I.H.; Klaasse, J.C.P.; Hagmusa, I.H.; Klaasse, J.C.P.

1997-01-01

UNiGe undergoes two magnetic transitions in zero field. Here, the magnetic diagrams of UNiGe for B parallel b and B parallel c are reported. We performed temperatures scans of the magnetization in static magnetic fields up to 19.5T applied along the b and c axes. For both orientations 3 magnetic phases have been identified in the B-T diagrams. We confirmed the previously reported phase boundaries for B parallel c, and in addition we determined the location of the phase boundaries for B parallel b. We discuss a possible relationship of the two zero-field antiferromagnetic phases (commensurate: T<42K; incommensurate: 42K< T<50K) and the field-induced phase, which, at low temperatures, occurs between 18 and 25T or 4 and 10T for B parallel b or B parallel c, respectively. Finally, we discuss the field dependence of the electronic contribution γ to the specific heat for B parallel c up to 17.5T, and we find that its field dependence is similar to the one found in more itinerant uranium compounds

Massive 3-loop ladder diagrams for quarkonic local operator matrix elements

Energy Technology Data Exchange (ETDEWEB)

Ablinger, Jakob; Schneider, Carsten [Johannes Kepler Univ., Linz (Austria). Research Inst. for Symbolic Computation; Bluemlein, Johannes; Hasselhuhn, Alexander; Wissbrock, Fabian [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Klein, Sebastian [Technische Hochschule Aachen (Germany). Inst. fuer Theoretische Physik

2012-06-15

3-loop diagrams of the ladder-type, which emerge for local quarkonic twist-2 operator matrix elements, are computed directly for general values of the Mellin variable N using Appell-function representations and applying modern summation technologies provided by the package Sigma and the method of hyperlogarithms. In some of the diagrams generalized harmonic sums with {xi} element of {l_brace}1,1/2,2{r_brace} emerge beyond the usual nested harmonic sums. As the asymptotic representation of the corresponding integrals shows, the generalized sums conspire giving well behaved expressions for large values of N. These diagrams contribute to the 3-loop heavy flavor Wilson coefficients of the structure functions in deep-inelastic scattering in the region Q{sup 2} >> m{sup 2}.

Massive 3-loop ladder diagrams for quarkonic local operator matrix elements

Energy Technology Data Exchange (ETDEWEB)

Ablinger, Jakob [Research Institute for Symbolic Computation (RISC), Johannes Kepler University, Altenbergerstrasse 69, A-4040 Linz (Austria); Bluemlein, Johannes, E-mail: johannes.bluemlein@desy.de [Deutsches Elektronen-Synchrotron, DESY, Platanenallee 6, D-15738 Zeuthen (Germany); Hasselhuhn, Alexander [Deutsches Elektronen-Synchrotron, DESY, Platanenallee 6, D-15738 Zeuthen (Germany); Klein, Sebastian [Research Institut fuer Theoretische Physik E, RWTH Aachen University, D-52056 Aachen (Germany); Schneider, Carsten [Research Institute for Symbolic Computation (RISC), Johannes Kepler University, Altenbergerstrasse 69, A-4040 Linz (Austria); Wissbrock, Fabian [Deutsches Elektronen-Synchrotron, DESY, Platanenallee 6, D-15738 Zeuthen (Germany)

2012-11-01

3-loop diagrams of the ladder-type, which emerge for local quarkonic twist-2 operator matrix elements, are computed directly for general values of the Mellin variable N using Appell-function representations and applying modern summation technologies provided by the package Sigma and the method of hyperlogarithms. In some of the diagrams generalized harmonic sums with {xi} Element-Of {l_brace}1,1/2,2{r_brace} emerge beyond the usual nested harmonic sums. As the asymptotic representation of the corresponding integrals shows, the generalized sums conspire giving well behaved expressions for large values of N. These diagrams contribute to the 3-loop heavy flavor Wilson coefficients of the structure functions in deep-inelastic scattering in the region Q{sup 2} Much-Greater-Than m{sup 2}.

Stochastic, real-space, imaginary-time evaluation of third-order Feynman–Goldstone diagrams

International Nuclear Information System (INIS)

Willow, Soohaeng Yoo; Hirata, So

2014-01-01

A new, alternative set of interpretation rules of Feynman–Goldstone diagrams for many-body perturbation theory is proposed, which translates diagrams into algebraic expressions suitable for direct Monte Carlo integrations. A vertex of a diagram is associated with a Coulomb interaction (rather than a two-electron integral) and an edge with the trace of a Green's function in real space and imaginary time. With these, 12 diagrams of third-order many-body perturbation (MP3) theory are converted into 20-dimensional integrals, which are then evaluated by a Monte Carlo method. It uses redundant walkers for convergence acceleration and a weight function for importance sampling in conjunction with the Metropolis algorithm. The resulting Monte Carlo MP3 method has low-rank polynomial size dependence of the operation cost, a negligible memory cost, and a naturally parallel computational kernel, while reproducing the correct correlation energies of small molecules within a few mE h after 10 6 Monte Carlo steps

Stochastic, real-space, imaginary-time evaluation of third-order Feynman–Goldstone diagrams

Energy Technology Data Exchange (ETDEWEB)

Willow, Soohaeng Yoo [Department of Chemistry, University of Illinois at Urbana-Champaign, 600 South Mathews Avenue, Urbana, Illinois 61801 (United States); Center for Superfunctional Materials, Department of Chemistry, Pohang University of Science and Technology, San 31, Hyojadong, Namgu, Pohang 790-784 (Korea, Republic of); Hirata, So, E-mail: sohirata@illinois.edu [Department of Chemistry, University of Illinois at Urbana-Champaign, 600 South Mathews Avenue, Urbana, Illinois 61801 (United States); CREST, Japan Science and Technology Agency, Saitama 332-0012 (Japan)

2014-01-14

A new, alternative set of interpretation rules of Feynman–Goldstone diagrams for many-body perturbation theory is proposed, which translates diagrams into algebraic expressions suitable for direct Monte Carlo integrations. A vertex of a diagram is associated with a Coulomb interaction (rather than a two-electron integral) and an edge with the trace of a Green's function in real space and imaginary time. With these, 12 diagrams of third-order many-body perturbation (MP3) theory are converted into 20-dimensional integrals, which are then evaluated by a Monte Carlo method. It uses redundant walkers for convergence acceleration and a weight function for importance sampling in conjunction with the Metropolis algorithm. The resulting Monte Carlo MP3 method has low-rank polynomial size dependence of the operation cost, a negligible memory cost, and a naturally parallel computational kernel, while reproducing the correct correlation energies of small molecules within a few mE{sub h} after 10{sup 6} Monte Carlo steps.

Modelling the continuous cooling transformation diagram of engineering steels using neural networks. Part I. Phase regions

Energy Technology Data Exchange (ETDEWEB)

Wolk, P.J. van der; Wang, J. [Delft Univ. of Technology (Netherlands); Sietsma, J.; Zwaag, S. van der [Delft Univ. of Technology, Lab. for Materials Science (Netherlands)

2002-12-01

A neural network model for the calculation of the phase regions of the continuous cooling transformation (CCT) diagram of engineering steels has been developed. The model is based on experimental CCT diagrams of 459 low-alloy steels, and calculates the CCT diagram as a function of composition and austenitisation temperature. In considering the composition, 9 alloying elements are taken into account. The model reproduces the original diagrams rather accurately, with deviations that are not larger than the average experimental inaccuracy of the experimental diagrams. Therefore, it can be considered an adequate alternative to the experimental determination of the CCT diagram of a certain steel within the composition range used. The effects of alloying elements can be quantified, either individually or in combination, with the model. Nonlinear composition dependencies are observed. (orig.)

Ground-state phase diagram of an (S, S') = (1, 2) spin-alternating chain with competing single-ion anisotropies

International Nuclear Information System (INIS)

Tonegawa, T; Okamoto, K; Sakai, T; Kaburagi, M

2009-01-01

Employing various numerical methods, we determine the ground-state phase diagram of an (S, S') = (1, 2) spin-alternating chain with antiferromagnetic nearest-neighboring exchange interactions and uniaxial single-ion anisotropies. The resulting phase diagram consists of eight kinds of phases including two phases which accompany the spontaneous breaking of the translational symmetry and a ferrimagnetic phase in which the ground-state magnetization varies continuously with the uniaxial single-ion anisotropy constants for the S=1 and S =2 spins. The appearance of these three phases is attributed to the competition between the uniaxial single-ion anisotropies of both spins.

High exhaust temperature, zoned, electrically-heated particulate matter filter

Science.gov (United States)

Gonze, Eugene V.; Paratore, Jr., Michael J.; Bhatia, Garima

2015-09-22

A system includes a particulate matter (PM) filter, an electric heater, and a control circuit. The electric heater includes multiple zones, which each correspond to longitudinal zones along a length of the PM filter. A first zone includes multiple discontinuous sub-zones. The control circuit determines whether regeneration is needed based on an estimated level of loading of the PM filter and an exhaust flow rate. In response to a determination that regeneration is needed, the control circuit: controls an operating parameter of an engine to increase an exhaust temperature to a first temperature during a first period; after the first period, activates the first zone; deactivates the first zone in response to a minimum filter face temperature being reached; subsequent to deactivating the first zone, activates a second zone; and deactivates the second zone in response to the minimum filter face temperature being reached.

Phase diagram of the ternary Zr-Ti-Sn system

International Nuclear Information System (INIS)

Arias, D.; Gonzalez Camus, M.

1987-01-01

It is well known that Ti stabilizes the high temperature cubic phase of Zr and that Sn stabilizes the low temperature hexagonal phase of Zr. The effect of Sn on the Zr-Ti diagram has been studied in the present paper. Using high purity metals, nine different alloys have been prepared, with 4-32 at % Ti, 0.7-2.2 at % Sn and Zr till 100%. Resistivity and optical and SEM metallography techniques have been employed. Effect of some impurities have been analyzed. The results are discussed and different isothermic sections of the ternary Zr-Ti-Sn diagram are presented. (Author) [es

Pourbaix Diagrams at Elevated Temperatures A Study of Zinc and Tin

Science.gov (United States)

Palazhchenko, Olga

Metals in industrial settings such as power plants are often subjected to high temperature and pressure aqueous environments, where failure to control corrosion compromises worker and environment safety. For instance, zircaloy (1.2-1.7 wt.% Sn) fuel rods are exposed to aqueous 250-310 °C coolant in CANDU reactors. The Pourbaix (EH-pH) diagram is a plot of electrochemical potential versus pH, which shows the domains of various metal species and by inference, corrosion susceptibility. Elevated temperature data for tin +II and tin +IV species were obtained using solid-aqueous phase equilibria with the respective oxides, in a batch vessel with in-situ pH measurement. Solubilities, determined via spectroscopic techniques, were used to calculate equilibrium constants and the Gibbs energies of Sn complexes for E-pH diagram construction. The SnOH3+ and Sn(OH )-5 species were incorporated, for the first time, into the 298.15 K and 358.15 K diagrams, with novel Go values determined at 358.15 K. Key words: Pourbaix diagrams, EH-pH, elevated temperatures, solubility, equilibrium, metal oxides, hydrolysis, redox potential, pH, thermochemical data, tin, zinc, zircaloy, corrosion, passivity.

Level Diagrams analysis of Pareto Front for multiobjective system redundancy allocation

International Nuclear Information System (INIS)

Zio, E.; Bazzo, R.

2011-01-01

Reliability-based and risk-informed design, operation, maintenance and regulation lead to multiobjective (multicriteria) optimization problems. In this context, the Pareto Front and Set found in a multiobjective optimality search provide a family of solutions among which the decision maker has to look for the best choice according to his or her preferences. Efficient visualization techniques for Pareto Front and Set analyses are needed for helping decision makers in the selection task. In this paper, we consider the multiobjective optimization of system redundancy allocation and use the recently introduced Level Diagrams technique for graphically representing the resulting Pareto Front and Set. Each objective and decision variable is represented on separate diagrams where the points of the Pareto Front and Set are positioned according to their proximity to ideally optimal points, as measured by a metric of normalized objective values. All diagrams are synchronized across all objectives and decision variables. On the basis of the analysis of the Level Diagrams, we introduce a procedure for reducing the number of solutions in the Pareto Front; from the reduced set of solutions, the decision maker can more easily identify his or her preferred solution.

Outer Retinal Changes Including the Ellipsoid Zone Band in Usher Syndrome 1B due to MYO7A Mutations.

Science.gov (United States)

Sumaroka, Alexander; Matsui, Rodrigo; Cideciyan, Artur V; McGuigan, David B; Sheplock, Rebecca; Schwartz, Sharon B; Jacobson, Samuel G

2016-07-01

To study transition zones from normal to abnormal retina in Usher syndrome IB (USH1B) caused by myosin 7A (MYO7A) mutations. Optical coherence tomography (OCT) scattering layers in outer retina were segmented in patients (n = 16, ages 2-42; eight patients had serial data, average interval 4.5 years) to quantify outer nuclear layer (ONL) and outer segments (OS) as well as the locus of EZ (ellipsoid zone) edge and its extent from the fovea. Static perimetry was measured under dark-adapted (DA) and light-adapted (LA) conditions. Ellipsoid zone edge in USH1B-MYO7A could be located up to 23° from the fovea. Ellipsoid zone extent constricted at a rate of 0.51°/year with slower rates at smaller eccentricities. A well-defined EZ line could be associated with normal or abnormal ONL and/or OS thickness; detectable ONL extended well beyond EZ edge. At the EZ edge, the local slope of LA sensitivity loss was 2.6 (±1.7) dB/deg for central transition zones. At greater eccentricities, the local slope of cone sensitivity loss was shallower (1.1 ± 0.4 dB/deg for LA) than that of rod sensitivity loss (2.8 ± 1.2 dB/deg for DA). In USH1B-MYO7A, constriction rate of EZ extent depends on the initial eccentricity of the transition. Ellipsoid zone edges in the macula correspond to large local changes in cone vision, but extramacular EZ edges show more pronounced losses on rod-based vision tests. It is advisable to use not only the EZ line but also other structural and functional parameters for estimating natural history of disease and possible therapeutic effects in future clinical trials of USH1B-MYO7A.

Global Water Cycle Diagrams Minimize Human Influence and Over-represent Water Security

Science.gov (United States)

Abbott, B. W.; Bishop, K.; Zarnetske, J. P.; Minaudo, C.; Chapin, F. S., III; Plont, S.; Marçais, J.; Ellison, D.; Roy Chowdhury, S.; Kolbe, T.; Ursache, O.; Hampton, T. B.; GU, S.; Chapin, M.; Krause, S.; Henderson, K. D.; Hannah, D. M.; Pinay, G.

2017-12-01

The diagram of the global water cycle is the central icon of hydrology, and for many people, the point of entry to thinking about key scientific concepts such as conservation of mass, teleconnections, and human dependence on ecological systems. Because humans now dominate critical components of the hydrosphere, improving our understanding of the global water cycle has graduated from an academic exercise to an urgent priority. To assess how the water cycle is conceptualized by researchers and the general public, we analyzed 455 water cycle diagrams from textbooks, scientific articles, and online image searches performed in different languages. Only 15% of diagrams integrated human activity into the water cycle and 77% showed no sign of humans whatsoever, although representation of humans varied substantially by region (lowest in China, N. America, and Australia; highest in Western Europe). The abundance and accessibility of freshwater resources were overrepresented, with 98% of diagrams omitting water pollution and climate change, and over 90% of diagrams making no distinction for saline groundwater and lakes. Oceanic aspects of the water cycle (i.e. ocean size, circulation, and precipitation) and related teleconnections were nearly always underrepresented. These patterns held across disciplinary boundaries and through time. We explore the historical and contemporary reasons for some of these biases and present a revised version of the global water cycle based on research from natural and social sciences. We conclude that current depictions of the global water cycle convey a false sense of water security and that reintegrating humans into water cycle diagrams is an important first step towards understanding and sustaining the hydrosocial cycle.

Visualizing Mortality Dynamics in the Lexis Diagram

DEFF Research Database (Denmark)

Rau, Roland; Bohk-Ewald, Christina; Muszynska, Magdalena M

This book visualizes mortality dynamics in the Lexis diagram. While the standard approach of plotting death rates is also covered, the focus in this book is on the depiction of rates of mortality improvement over age and time. This rather novel approach offers a more intuitive understanding...... of the underlying dynamics, enabling readers to better understand whether period- or cohort-effects were instrumental for the development of mortality in a particular country. Besides maps for single countries, the book includes maps on the dynamics of selected causes of death in the United States...... Software to produce these types of surface maps. Readers are encouraged to use the presented tools to visualize other demographic data or any event that can be measured by age and calendar time, allowing them to adapt the methods to their respective research interests. The intended audience is anyone who...

Essential Magnesium Alloys Binary Phase Diagrams and Their Thermochemical Data

Directory of Open Access Journals (Sweden)

Mohammad Mezbahul-Islam

2014-01-01

Full Text Available Magnesium-based alloys are becoming a major industrial material for structural applications because of their potential weight saving characteristics. All the commercial Mg alloys like AZ, AM, AE, EZ, ZK, and so forth series are multicomponent and hence it is important to understand the phase relations of the alloying elements with Mg. In this work, eleven essential Mg-based binary systems including Mg-Al/Zn/Mn/Ca/Sr/Y/Ni/Ce/Nd/Cu/Sn have been reviewed. Each of these systems has been discussed critically on the aspects of phase diagram and thermodynamic properties. All the available experimental data has been summarized and critically assessed to provide detailed understanding of the systems. The phase diagrams are calculated based on the most up-to-date optimized parameters. The thermodynamic model parameters for all the systems except Mg-Nd have been summarized in tables. The crystallographic information of the intermetallic compounds of different binary systems is provided. Also, the heat of formation of the intermetallic compounds obtained from experimental, first principle calculations and CALPHAD optimizations are provided. In addition, reoptimization of the Mg-Y system has been done in this work since new experimental data showed wider solubility of the intermetallic compounds.

Calculating Asteroseismic Diagrams for Solar-Like Oscillations

DEFF Research Database (Denmark)

White, T.R.; Bedding, T.R.; Stello, D.

2011-01-01

With the success of the Kepler and CoRoT missions, the number of stars with detected solar-like oscillations has increased by several orders of magnitude; for the first time we are able to perform large-scale ensemble asteroseismology of these stars. In preparation for this golden age of asterose......With the success of the Kepler and CoRoT missions, the number of stars with detected solar-like oscillations has increased by several orders of magnitude; for the first time we are able to perform large-scale ensemble asteroseismology of these stars. In preparation for this golden age...... of these stars. We investigate the scaling relation between the large frequency separation, Δν, and mean stellar density. Furthermore we present model evolutionary tracks for several asteroseismic diagrams. We have extended the so-called C-D diagram beyond the main sequence to the subgiants and the red giant...

Sea-floor texture and physiographic zones of the inner continental shelf from Salisbury to Nahant, Massachusetts, including the Merrimack Embayment and Western Massachusetts Bay

Science.gov (United States)

Pendleton, Elizabeth E.; Barnhardt, Walter A.; Baldwin, Wayne E.; Foster, David S.; Schwab, William C.; Andrews, Brian D.; Ackerman, Seth D.

2015-10-26

A series of maps that describe the distribution and texture of sea-floor sediments and physiographic zones of Massachusetts State waters from Nahant to Salisbury, Massachusetts, including western Massachusetts Bay, have been produced by using high-resolution geophysical data (interferometric and multibeam swath bathymetry, lidar bathymetry, backscatter intensity, and seismic reflection profiles), sediment samples, and bottom photographs. These interpretations are intended to aid statewide efforts to inventory and manage coastal and marine resources, link with existing data interpretations, and provide information for research focused on coastal evolution and environmental change. Marine geologic mapping of the inner continental shelf of Massachusetts is a statewide cooperative effort of the U.S. Geological Survey and the Massachusetts Office of Coastal Zone Management.

Creating Royal Australian Navy Standard Operating Procedures using Flow Diagrams

Science.gov (United States)

2015-08-01

departments and check the naming and number conventions have been adhered to. They will also coordinate the review process and check that the definitive ...possible. If the performer is a team the composition of the team should be described in the SOP, either as a definition or in the description of a...diagram a video could be used. A hyperlink to a video of the process to follow could be added to the flow diagram or the description section of the

Algorithms and programs for consequence diagram and fault tree construction

International Nuclear Information System (INIS)

Hollo, E.; Taylor, J.R.

1976-12-01

A presentation of algorithms and programs for consequence diagram and sequential fault tree construction that are intended for reliability and disturbance analysis of large systems. The system to be analyzed must be given as a block diagram formed by mini fault trees of individual system components. The programs were written in LISP programming language and run on a PDP8 computer with 8k words of storage. A description is given of the methods used and of the program construction and working. (author)

On the distribution of silicic acid as a frontal zone tracer in the Indian sector of the Southern Ocean

Directory of Open Access Journals (Sweden)

R. Prego

1999-06-01

Full Text Available The subantarctic frontal zone surveyed during the April-May 1991 SUZIL cruise in the Crozet-Kerguelen-Amsterdam area shows a strong horizontal (north to south gradient of dissolved silicate, increasing with depth, from 5 to 10 µmolSi kg-1 at 100 m, and 10 to 70 µmolSi kg-1 at 600 m. The northern limit of this frontal zone, which is formed by the confluence of the Subtropical and Subantarctic Fronts, is delimited at the surface by the 2 µmolSi kg-1 silicate isoline. Silicate-salinity diagrams also allow different water regimes to be positioned relative to the frontal zone. This sloping interface is between two water bodies, one to the north with more saline subtropical waters of less concentrated silicate than the southern one, corresponding to subantarctic waters which are less saline and richer in silicate. It is concluded that dissolved silicate can be used as a useful tracer of frontal zone water masses in the Indian sector of the Southern Ocean, providing a sound complement to other hydrographic data.

Calculation of binary phase diagrams between the actinide elements, rare earth elements, and transition metal elements

International Nuclear Information System (INIS)

Selle, J.E.

1992-01-01

Attempts were made to apply the Kaufman method of calculating binary phase diagrams to the calculation of binary phase diagrams between the rare earths, actinides, and the refractory transition metals. Difficulties were encountered in applying the method to the rare earths and actinides, and modifications were necessary to provide accurate representation of known diagrams. To calculate the interaction parameters for rare earth-rare earth diagrams, it was necessary to use the atomic volumes for each of the phases: liquid, body-centered cubic, hexagonal close-packed, and face-centered cubic. Determination of the atomic volumes of each of these phases for each element is discussed in detail. In some cases, empirical means were necessary. Results are presented on the calculation of rare earth-rare earth, rare earth-actinide, and actinide-actinide diagrams. For rare earth-refractory transition metal diagrams and actinide-refractory transition metal diagrams, empirical means were required to develop values for the enthalpy of vaporization for rare earth elements and values for the constant (C) required when intermediate phases are present. Results of using the values determined for each element are presented

Applications of phase diagrams in metallurgy and ceramics

International Nuclear Information System (INIS)

Carter, G.C.

1978-03-01

The workshop represents an effort to coordinate and reinforce the current efforts on compilation of phase diagrams of alloys and ceramics. Many research groups and individual scientists throughout the world are concerned with phase equilibrium data. Specialized expertise exists in small institutions as well as large laboratories. If this talent can be effecively utilized through a cooperative effort, the needs for such data can be met. The Office of Standard Reference Data, which serves as the program management office for the National Standard Reference Data System, is eager to work with all groups concerned with this problem. Through a cooperative international effort we can carry out a task which has become too large for an individual. Volume 2 presents computational techniques for phase diagram construction

49 CFR 1152.13 - Amendment of the system diagram map or narrative.

Science.gov (United States)

2010-10-01

... 49 Transportation 8 2010-10-01 2010-10-01 false Amendment of the system diagram map or narrative... map or narrative. (a) Each carrier shall be responsible for maintaining the continuing accuracy of its system diagram map and the accompanying line descriptions or narrative. Amendments may be filed at any...

The Traders' Cross: Identifying Traders' Surpluses in the Traditional Edgeworth Exchange Diagram

Science.gov (United States)

Beaulier, Scott A.; Prychitko, David L.

2010-01-01

The Edgeworth exchange diagram is a traditional tool of undergraduate microeconomic theory that depicts the mutually beneficial gains from voluntary trade. The authors take the analysis one step further. They identify the buyer's and seller's surpluses that accrue to both trading parties in the Edgeworth diagram. This is a straightforward exercise…

How to Draw Energy Level Diagrams in Excitonic Solar Cells.

Science.gov (United States)

Zhu, X-Y

2014-07-03

Emerging photovoltaic devices based on molecular and nanomaterials are mostly excitonic in nature. The initial absorption of a photon in these materials creates an exciton that can subsequently dissociate in each material or at their interfaces to give charge carriers. Any attempt at mechanistic understanding of excitonic solar cells must start with drawing energy level diagrams. This seemingly elementary exercise, which is described in textbooks for inorganic solar cells, has turned out to be a difficult subject in the literature. The problem stems from conceptual confusion of single-particle energy with quasi-particle energy and the misleading practice of mixing the two on the same energy level diagram. Here, I discuss how to draw physically accurate energy diagrams in excitonic solar cells using only single-particle energies (ionization potentials and electron affinities) of both ground and optically excited states. I will briefly discuss current understanding on the electronic energy landscape responsible for efficient charge separation in excitonic solar cells.

True strain-temperature diagram and structural aspects of molybdenum fracture

International Nuclear Information System (INIS)

Vasil'ev, A.D.; Gornaya, I.D.; Moiseev, V.F.; Pechkovskij, Eh.P.; Ponomarev, S.S.; Trefilov, V.I.

1982-01-01

For the purpose of studying the regularities of tough fracture of polycrystal molybdenum and explaining characteristic types of uniaxial tensile fractures in the 100-1000 deq C temperature range it is suggested for the first time to use the true strain-temperature (TST) diagram which combines a diagram of structural states and temperature dependence of a number of critical strains reflecting the dynamics of emergence and development of micro-non continuities in a tension specimen. It is shown that in the polycrystal molybdenum the basic parameters controlling the course and the magnitude of separate strain stages as well as the transition to fracture are the strain hardening coefficient and the elasticity limit relation to the strain hardening coefficient at the first stage (homoo.eneous dislocations distribution stage). The TST diagram permits also to explain the following phenomena: the nature of cold brittleness upper temperature, the observed change of fracture mechanisms with the temperature increase, the fracture surface origin

Use of intelligent loop diagrams at San Onofre Nuclear Generation Station (SONGS)

International Nuclear Information System (INIS)

Groves, J.E.; Johnson, K.I.; Foulk, J.; Reinschmidt, K.F.; Tutos, N.C.

1991-01-01

The use of advanced information systems will result in five million dollars potential cost reduction and two years less time for producing over 2000 Instrumentation and Control Loop Diagrams for the three nuclear units at San Onofre Nuclear Generating Station (SONGS). This new information technology will also assist plant management at SONGS in generating even larger savings from reduction in operations and maintenance costs. The key element of the new solution is the use of plant drawings, the traditional primary source of plant information, for on-line access to all plant databases and information systems, by replacing paper drawings with intelligent electronic drawings. The implementation of this concept for the Instrumentation and Control Loop Diagrams, presently in progress, is part of the Integrated Nuclear Data Management Systems (INDAMS) program at SONGS, a joint effort which includes support from Stone and Webster Advanced Systems Development Services, International Business Machines Corporation (IBM), and Dassault Systems of France. The initial results have encouraged plant management to speed up the implementation process

Phase diagram distortion from traffic parameter averaging.

NARCIS (Netherlands)

Stipdonk, H. Toorenburg, J. van & Postema, M.

2010-01-01

Motorway traffic congestion is a major bottleneck for economic growth. Therefore, research of traffic behaviour is carried out in many countries. Although well describing the undersaturated free flow phase as an almost straight line in a (k,q)-phase diagram, congested traffic observations and

Show Me Your Opinion. Perceptual Cues in Creating and Reading Argument Diagrams

Science.gov (United States)

van Amelsvoort, Marije; Maes, Alfons

2016-01-01

In argument diagrams, perceptual cues are important to aid understanding. However, we do not know what perceptual cues are used and produced to aid understanding. We present two studies in which we investigate (1) which spatial, graphical and textual elements people spontaneously use in creating for-against argument diagrams, and (2) how people…

Construction of Eh-pH and other stability diagrams of uranium in a multicomponent system with a microcomputer

International Nuclear Information System (INIS)

Haung, H.; Cuentas, L.

1989-01-01

Stability diagrams for a multicomponent system in aqueous chemistry provide important information for hydrometallurgy, corrosion science, geochemistry and environmental science. Two distinct types of diagrams constructed are predominance diagrams and distribution diagrams. The ability to construct stability diagrams easily, quickly and accurately is most helpful in research and development and in academic programs. The use of a microcomputer is handicapped by slow speed and limited memory. Developing program methods that promote easy calculation and plot the diagram directly on a CRT or a plotter is a primary concern. As presented in this paper, the calculation of equilibrium and boundary constraints, combined with isolation of stability areas, works well for constructing predominance diagrams. Equilibrium constraints can be obtained based on free energies of formation. Boundary constraints for the ligand component are the boundary of the diagram, and constraints for the main component are the surrounding lines of each dominant ligand. Other considerations regarding the chemical model, mathematics computation and the use of microcomputers pertaining to diagram construction are discussed. The uranium in a multicomponent system is used for demonstration

Infrared observations of giant elliptical galaxies: (V-K) colors and the infrared Hubble diagram

International Nuclear Information System (INIS)

Grasdalen, G.L.

1980-01-01

The (V-K) colors of giant elliptical galaxies as a function of redshift are discussed. Present data are consistent with mild color evolution at z approximately 0.45. An infrared Hubble (redshift-magnitude) diagram is given. Cosmological models with q 0 =0 and no luminosity evolution are clearly excluded by the present data. A wide variety of models including those with q 0 =0 are permissible if luminosity evolution is included. Instrumental and programmatic implications of these results are summarized. (Auth.)

Dry Transfer Facility No.1 - Ventilation Confinement Zoning Analysis

International Nuclear Information System (INIS)

K.D. Draper

2005-01-01

The purpose of this analysis is to establish the preliminary Ventilation Confinement Zone (VCZ) for the Dry Transfer Facility (DTF). The results of this document is used to determine the air quantities for each VCZ that will eventually be reflected in the development of the Ventilation Flow Diagrams. The calculations contained in this document were developed by D and E/Mechanical-HVAC and are intended solely for the use of the D and E/Mechanical-HVAC department in its work regarding the HVAC system for the Dry Transfer Facility. Yucca Mountain Project personnel from the D and E/Mechanical-HVAC department should be consulted before use of the calculation for purposes other than those stated herein or used by individuals other than authorized personnel in D and E/Mechanical-HVAC department

Evaluated phase diagrams of binary metal-tellurium systems of the D-block transition elements

International Nuclear Information System (INIS)

Chattopadhyay, G.; Bharadwaj, S.R.

1989-01-01

The binary phase diagrams of metal-tellurium systems for twenty seven d-block transition elements have been critically evaluated. Complete phase diagrams are presented for the elements, chromium, manganese, iron, cobalt, nickel, copper, molybdenum, palladium, silver, lanthanum, platinum and gold, whereas, for scandium, titanium, vanadium, yttrium, zirconium, niobium, technitium, ruthenium, rhodium, hafnium, tantalum, tungsten , rhenium, osmium and iridium, the phase diagrams are incomplete and tentative. (author). 20 refs., 27 tabs., 27 figs

Planetary populations in the mass-period diagram: A statistical treatment of exoplanet formation and the role of planet traps

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, Yasuhiro [Currently EACOA Fellow at Institute of Astronomy and Astrophysics, Academia Sinica (ASIAA), Taipei 10641, Taiwan. (China); Pudritz, Ralph E., E-mail: yasu@asiaa.sinica.edu.tw, E-mail: pudritz@physics.mcmaster.ca [Also at Origins Institute, McMaster University, Hamilton, ON L8S 4M1, Canada. (Canada)

2013-11-20

The rapid growth of observed exoplanets has revealed the existence of several distinct planetary populations in the mass-period diagram. Two of the most surprising are (1) the concentration of gas giants around 1 AU and (2) the accumulation of a large number of low-mass planets with tight orbits, also known as super-Earths and hot Neptunes. We have recently shown that protoplanetary disks have multiple planet traps that are characterized by orbital radii in the disks and halt rapid type I planetary migration. By coupling planet traps with the standard core accretion scenario, we showed that one can account for the positions of planets in the mass-period diagram. In this paper, we demonstrate quantitatively that most gas giants formed at planet traps tend to end up around 1 AU, with most of these being contributed by dead zones and ice lines. We also show that a large fraction of super-Earths and hot Neptunes are formed as 'failed' cores of gas giants—this population being constituted by comparable contributions from dead zone and heat transition traps. Our results are based on the evolution of forming planets in an ensemble of disks where we vary only the lifetimes of disks and their mass accretion rates onto the host star. We show that a statistical treatment of the evolution of a large population of planetary cores caught in planet traps accounts for the existence of three distinct exoplanetary populations—the hot Jupiters, the more massive planets around r = 1 AU, and the short-period super-Earths and hot Neptunes. There are very few populations that feed into the large orbital radii characteristic of the imaged Jovian planet, which agrees with recent surveys. Finally, we find that low-mass planets in tight orbits become the dominant planetary population for low-mass stars (M {sub *} ≤ 0.7 M {sub ☉}).

Experimental determination of the Ta–Ge phase diagram

Energy Technology Data Exchange (ETDEWEB)

Araújo Pinto da Silva, Antonio Augusto, E-mail: aaaps@ppgem.eel.usp.br [EEL/USP – Escola de Engenharia de Lorena (EEL), Universidade de São Paulo (USP), Pólo Urbo-Industrial Gleba AI-6, 12602-810 Lorena, SP (Brazil); Coelho, Gilberto Carvalho [EEL/USP – Escola de Engenharia de Lorena (EEL), Universidade de São Paulo (USP), Pólo Urbo-Industrial Gleba AI-6, 12602-810 Lorena, SP (Brazil); UniFoa – Centro Universitário de Volta Redonda, Núcleo de Pesquisa, Campus Três Poços, Avenida Paulo Erlei Alves Abrantes, 1325, Bairro Três Poços, 27240-560 Volta Redonda, RJ (Brazil); Nunes, Carlos Angelo; Suzuki, Paulo Atsushi [EEL/USP – Escola de Engenharia de Lorena (EEL), Universidade de São Paulo (USP), Pólo Urbo-Industrial Gleba AI-6, 12602-810 Lorena, SP (Brazil); Fiorani, Jean Marc; David, Nicolas; Vilasi, Michel [Université de Lorraine, Institut Jean Lamour, Faculté des Sciences et Technologies, BP 70239, F-54506 Vandoeuvre-lès-Nancy (France)

2013-11-05

Highlights: •Ta–Ge phase diagram propose for the first time. •The phase αTa{sub 5}Ge{sub 3} was not observed in samples investigated in this work. •Three eutectics reactions where determined with the liquid compositions at 20.5; 28.0; 97.0 at.% Ge. -- Abstract: In the present work, the Ta–Ge phase diagram has been experimentally studied, considering the inexistence of a Ta–Ge phase diagram in the literature. The samples were prepared via arc melting and characterized by Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDS) and X-ray Diffraction (XRD). The intermetallics phases βTa{sub 3}Ge, αTa{sub 3}Ge, βTa{sub 5}Ge{sub 3} and TaGe{sub 2} where confirmed in this system. Three eutectics reactions where determined with the liquid compositions at 20.5; 28.0; 97.0 at.% Ge. The phases βTa{sub 3}Ge and βTa{sub 5}Ge{sub 3} solidifies congruently while TaGe{sub 2} is formed through a peritectic transformation. The temperature of the Ta-rich eutectic (L ↔ Ta{sub ss} + βTa{sub 3}Ge) was measured by the Pirani-Alterthum method at 2440 °C and the Ge-rich eutectic (L ↔ TaGe{sub 2} + Ge{sub ss}) by DTA at 937 °C.

The isometric log-ratio (ilr)-ion plot: A proposed alternative to the Piper diagram

Science.gov (United States)