Origin of absorption peaks in reflection loss spectrum in Ku- frequency band of Co-Zr substituted strontium hexaferrites prepared using sucrose precursor

Energy Technology Data Exchange (ETDEWEB)

Narang, Sukhleen Bindra, E-mail: sukhleen2@yahoo.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar (India); Pubby, Kunal, E-mail: kunalpubby02@gmail.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar (India); Chawla, S.K., E-mail: sschawla118@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar (India); Kaur, Prabhjyot, E-mail: prabhjyot.2525@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar (India)

2017-03-15

This study presents the detailed explanation of the factors, contributing towards the absorption peaks in reflection loss spectrum of hexaferrites. Cobalt-Zirconium substituted strontium hexaferrites, synthesized using sucrose precursor sol-gel technique, were analyzed in 12.4–18 GHz frequency range. The concepts of impedance matching through quarter wavelength condition, complex thickness, dielectric phase angle and attenuation constant have been used to determine the location as well as intensity of absorption peaks. This study also demonstrates the potential application of three compositions of this series with doping content (x)==0.0, 0.6 and 0.8 as an effective microwave absorbers in Ku-frequency band. - Highlights: • EM analysis of Sr Hexaferrites in Ku-band. • Factors towards absorption peak intensity & location.

Growth, structural and magnetic characterization of Al-substituted barium hexaferrite single crystals

International Nuclear Information System (INIS)

Vinnik, D.A.; Zherebtsov, D.A.; Mashkovtseva, L.S.; Nemrava, S.; Bischoff, M.; Perov, N.S.; Semisalova, A.S.; Krivtsov, I.V.; Isaenko, L.I.; Mikhailov, G.G.; Niewa, R.

2014-01-01

Highlights: • Growth of large Al-substituted crystals BaFe 12−x Al x O 19. • Al-content controllable by flux composition. • Crystallographic site preference of Al unraveled. • Magnetic characterization depending on Al-content. - Abstract: Large single crystals of aluminum-substituted M-type barium hexaferrite BaFe 12−x Al x O 19 were obtained from carbonate flux. The Al content in the crystals can be controlled via the Al content of the flux up to x = 1.1 according to single crystal X-ray structure refinements. Al shows a distinct preference to substitute Fe on crystallographic sites with high coordination numbers by oxygen atoms, whereas no significant amounts of Al can be found on a tetrahedrally coordinated site. An increasing amount of the aluminum dopant results in a monotonous reduction of the Curie temperature from 440 to 415 °C and the saturation magnetization at room temperature from 68 to 57 emu/g for single crystal and from 61 to 53 emu/g for powder samples

Influence of La-Mn substitutions on magnetic properties of M-type strontium hexaferrites

Science.gov (United States)

Zi, Z. F.; Ma, X. H.; Wei, Y. Y.; Liu, Q. C.; Zhang, M.; Zhu, X. B.; Sun, Y. P.

2018-05-01

M-type strontium hexaferrites of Sr1-xLaxFe12-xMnxO19 (0.0≤x≤0.4) were synthesized by the chemical coprecipitation method. X-ray diffraction (XRD) studies indicate that the samples are single-phase with the space group of P63/mmc. The results of field-emission scanning electronic microscopy (FE-SEM) show that the grains are regular hexagonal platelets with sizes from 0.7 to 1.4 μm. It is observed that the value of Hc increases at low substitution (x ≤ 0.1), reaches a maximum at x = 0.1 and then decreases at x ≥ 0.1, while the value of Ms decreases monotonously with increasing x. The variations of magnetic properties can be tentatively attributed to the effects of La-Mn substitutions. The results above indicate that our samples might be promising candidates for permanent magnets in the future.

Electrical conductivity of cobalt–titanium substituted SrCaM hexaferrites

International Nuclear Information System (INIS)

Eraky, M.R.

2012-01-01

A series of polycrystalline M-type hexagonal ferrites with the composition Sr 0.5 Ca 0.5 Co x Ti x Fe 12−2x O 19 (where x=0.0–0.8) were prepared by the conventional ceramic technique. The electrical conductivity has been measured from 300 to 590 K. The dc conductivity, σ dc , exhibited a semiconductor behavior. The negative sign of thermoelectric power coefficient S reveals that all samples are n-type semiconductors. Both σ dc and mobility, μ d , increases with the substitution of Co 2+ and Ti 4+ ions, reach maximum at x=0.4 and start decreasing at x>0.4. Many conduction mechanisms were discussed to explain the electric conduction in the system. It was found that the hopping conduction is the predominant conduction mechanism. For samples with compositional parameter x=0.0 and 0.8, the band conduction mechanism shares in electric conduction beside the hopping process. - Highlights: ► SrCaCoTiM hexaferrites have been prepared by conventional ceramic technique. ► The electrical conductivity exhibited a semiconductor behavior. There is an increase in conductivity up to x=0.4 for Co and Ti substitution. ► The hopping conduction is the predominant conduction mechanism.

Crystal structure, magnetic properties and advances in hexaferrites: A brief review

Science.gov (United States)

Jotania, Rajshree

2014-10-01

Hexaferrites are hard magnetic materials and specifically ferri-magnetic oxides with hexagonal magnetoplumbite type crystallographic structure. Hexagonal ferrites are used as permanent magnets, high-density perpendicular and magneto-optical recording media, and microwave devices like resonance isolators, filters, circulators, phase shifters because of their high magnetic permeability, high electrical resistivity and moderable permittivity. In addition to these; hexagonal ferrites have excellent chemical stability, mechanical hardness and low eddy current loss at high frequencies. The preparation of hexaferrites is a complicated process. Various experimental techniques like standard ceramic techniques, solvent free synthesis route, co precipitation, salt-melt, ion exchange, sol-gel, citrate synthesis, hydrothermal synthesis, spray drying, water-in-oil microemulsion, reverse micelle etc are used to prepare hexaferrite materials. Structural, dielectric and magnetic properties, crystallite size of hexaferrites depend upon nature of substituted ions, method of preparation, sintering temperature and time. The recent interest is nanotechnology, the development of hexaferrite fibres and composites with carbon nano tubes (CNT). Magnetic properties of some doped and un-doped hexaferrites are discussed here. Recent advances in hexaferrites also highlighted in present paper.

Effect of pb on the magnetic interactions of the M-type hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Guerrero, A.L., E-mail: azdlobo@gmail.com [Instituto de Física de la Universidad Autónoma de San Luis Potosí, Álvaro Obregón No. 64, Col. Centro, San Luis Potosí, S.L.P. 78000, México (Mexico); Mirabal-García, M. [Instituto de Física de la Universidad Autónoma de San Luis Potosí, Álvaro Obregón No. 64, Col. Centro, San Luis Potosí, S.L.P. 78000, México (Mexico); Palomares-Sánchez, S.A.; Martínez, J.R. [Facultad de Ciencias de la Universidad Autónoma de San Luis Potosí, Álvaro Obregón No. 64, Col. Centro, San Luis Potosí, S.L.P. 78000, México (Mexico)

2016-02-01

This work reports the magnetic interactions of M-type lead hexaferrites. The samples were prepared using the solid state reaction method varying the lead concentration and compensating its lost by thermal treatment in order to obtain pure phases. The structural characterization was made through X-ray diffraction and the Rietveld refinement method. The morphology and grain-growth analysis were carried out using scanning electron microscopy. The magnetic interactions were studied through isothermal remanence (IRM) and DC demagnetization (DCD) remanence curves and through the construction of Henkel plots. By analyzing deviations from the Stoner–Wohlfarth model for non-interacting particles, it was determined the way in which lead modifies the interaction state in the hexaferrites. The experimental results show that the demagnetizing interactions prevail in systems with high lead content, and as lead concentration diminishes the intensity of magnetic interactions also decreases giving rise to magnetizing interactions - Highlights: • Construction of Henkel Plots of substituted hexaferrites. • Evaluation of magnetostatic and exchange interactions. • Effect of lead substitution on magnetic properties of the hexaferrites.

Synthesis and characterization of the Y-type barium hexaferrite (Ba_2CoZnFe_1_2O_2_2) obtained by ultrasonic interdispersion of chemical precitates

International Nuclear Information System (INIS)

Junior, E.S.G.; Santos, M.R.C.; Jardim, P.M.; Ogasawara, T.; Almeida, L.H.

2011-01-01

This work is to study the synthesis and characterization of the Y-type barium hexaferrite powder (Ba2CoZnFe12O22) by chemical precipitation of the precursor materials Fe(OH)3, Co(OH)2, Zn(OH)2 and Ba(OH)2 separately and ultrasonic inter-dispersion, followed by drying and calcining. The study shows that the phase formation of the Y-type barium hexaferrite begins to emerge already at a temperature of 900 ° C with further phases still present, characterized by X-ray diffraction, the grain growth of the final product of the synthesis as a function of calcination temperature is visible by SEM, the measured magnetic of the powder through the hysteresis curve confirms that the material is magnetically soft at room temperature. The synthesis method developed in this research is an option to achieve the results that would be obtained if the co-precipitation of the ferric hydroxides, of cobalt, zinc and barium were thermodynamically possible. (author)

Ce{sup 3+} incorporated structural and magnetic properties of M type barium hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Pawar, R.A. [Department of Physics, Arts, Commerce and Science College, Satral, MS (India); Desai, S.S.; Tamboli, Q.Y. [Materials Research Laboratory, Shrikrishna Mahavidyalaya, Gunjoti 413613, MS (India); Shirsath, Sagar E. [Spin Device Technology Center, Faculty of Engineering, Shinshu University, Nagano 380-8553 (Japan); Patange, S.M., E-mail: smpatange@rediffmail.com [Materials Research Laboratory, Shrikrishna Mahavidyalaya, Gunjoti 413613, MS (India)

2015-03-15

M type barium hexaferrites BaCe{sub x}Fe{sub 12−x}O{sub 19} (0≤x≤0.3) (BCFO) were synthesized by the sol–gel auto combination method. Optimum annealing temperature of hexagonal phase was determined by using the TGA analysis. The annealing temperature form the TGA is 1000 °C samples annealed 1000 °C for 5 h to produce M type hexaferrites. X-ray diffraction data run to full Prof Program (Winploter 2010) pattern indicate that samples are single phase hexagonal structure with space group P6{sub 3}/mmc. Lattice parameter ‘a’ and ‘c’ increase with increase in Ce content x. Results of field emission scanning electron microscope show that the grains are regular hexagonal platelets with sizes from 0.3 to 1.4 μm. It is observed that from M–H curve value of the saturation magnetization and coercivity decreases with increasing x. Curie temperature from magnetization with temperature plot is found to decrease with Ce{sup 3+} substitution x due to decreases in magnetic interaction. - Highlights: • Ce{sup 3+} substituted Ba hexaferrites. • Increased coercivity with Ce{sup 3+} substitution. • Decrease in saturation magnetization and Curie temperature.

Microstructure and magnetic properties of Zr-Mn substituted M-type SrLa hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Yang, Yujie; Wang, Fanhou; Shao, Juxiang; Huang, Duohui [Yibin University, Computational Physics Key Laboratory of Sichuan Province, School of Physics and Electronic Engineering, Yibin (China); Batoo, Khalid Mujasam [King Saud University, King Abdullah Institute for Nanotechnology, Riyadh (Saudi Arabia)

2017-09-15

In this study, we have synthesized the M-type SrLa hexaferrites with nominal compositions of Sr{sub 0.75}La{sub 0.25}Fe{sub 12.0-2x}(ZrMn){sub x}O{sub 19} (0.0 ≤ x ≤ 0.75) by the solid-state method techniques. The phase compositions of the samples were confirmed by X-ray diffraction analysis. X-ray diffraction analysis exhibits that all the synthesized M-type hexaferrite magnetic powders are in single magetoplumbite structure and no impurity phase is observed, and with the increase of ZrMn content (x), (107) and (114) peaks are broadened and the 2 θ values of (107) and (114) peaks shift towards lower angles. It is observed that lattice constants (c and a) increase with increasing ZrMn content (x) from 0.00 to 0.75. The morphology of the M-type hexaferrites was characterized by a field emission scanning electron microscopy (FE-SEM). FE-SEM images show that the M-type hexaferrite have formed hexagonal structures. Magnetization properties were measured at room temperature using a physical property measurement system-vibrating sample magnetometer. The saturation magnetization (M{sub s}), remanent magnetization (M{sub r}) and coercivity (H{sub c}) are calculated from magnetic hysteresis loops. M{sub s}, M{sub r} and M{sub r}/M{sub s} ratio first increase with increasing ZrMn content (x) from 0.00 to 0.15, and then decrease when ZrMn content (x) ≥0.15. H{sub c} decreases with the increase of ZrMn content (x) from 0.00 to 0.75. (orig.)

Soft x-ray resonant diffraction study of magnetic structure in magnetoelectric Y-type hexaferrite

Science.gov (United States)

Ueda, H.; Tanaka, Y.; Wakabayashi, Y.; Kimura, T.

2018-05-01

The effect of magnetic field on the magnetic structure associated with magnetoelectric properties in a Y-type hexaferrite, Ba1.3Sr0.7CoZnFe11AlO22, was investigated by utilizing the soft x-ray resonant diffraction technique. In this hexaferrite, the so-called alternating longitudinal conical phase is stabilized at room temperature and zero magnetic field. Below room temperature, however, this phase is transformed into the so-called transverse conical phase by applying an in-plane magnetic field (≈ 0.3 T). The transverse conical phase persists even after removing the magnetic field. The magnetoelectricity, which is magnetically-induced electric polarization, observed in the hexaferrite is discussed in terms of the temperature-dependent magnetic structure at zero field.

Effects of Al substitution and thermal annealing on magnetoelectric Ba0.5Sr1.5Zn2Fe12O22 investigated by the enhancement factor of 57Fe nuclear magnetic resonance.

Science.gov (United States)

Kwon, Sangil; Kang, Byeongki; Kim, Changsoo; Jo, Euna; Lee, Soonchil; Chai, Yi Sheng; Chun, Sae Hwan; Kim, Kee Hoon

2014-04-09

The magnetoelectric properties of hexaferrite Ba0.5Sr1.5Zn2Fe12O22 are significantly improved by Al substitution and thermal annealing. Measuring the enhancement factor of 57Fe NMR, we found direct microscopic evidence that the magnetic moments of the L and S blocks are rotated by a magnetic field in such a way as to increase the net magnetic moment of a magnetic unit, even after the field is removed. Al substitution makes magnetoelectric property arise easily by suppressing the easy-plane anisotropy. The effect of thermal annealing is to stabilize the multiferroic state by reducing the number of pinning sites and the electron spin fluctuation. The transverse conic structure gradually changes to the alternating longitudinal conic structure where spins fluctuate more severely.

Crystal growth of hexaferrite architecture for magnetoelectrically tunable microwave semiconductor integrated devices

Science.gov (United States)

Hu, Bolin

Hexaferrites (i.e., hexagonal ferrites), discovered in 1950s, exist as any one of six crystallographic structural variants (i.e., M-, X-, Y-, W-, U-, and Z-type). Over the past six decades, the hexaferrites have received much attention owing to their important properties that lend use as permanent magnets, magnetic data storage materials, as well as components in electrical devices, particularly those operating at RF frequencies. Moreover, there has been increasing interest in hexaferrites for new fundamental and emerging applications. Among those, electronic components for mobile and wireless communications especially incorporated with semiconductor integrated circuits at microwave frequencies, electromagnetic wave absorbers for electromagnetic compatibility, random-access memory (RAM) and low observable technology, and as composite materials having low dimensions. However, of particular interest is the magnetoelectric (ME) effect discovered recently in the hexaferrites such as SrScxFe12-xO19 (SrScM), Ba2--xSrxZn 2Fe12O22 (Zn2Y), Sr4Co2Fe 36O60 (Co2U) and Sr3Co2Fe 24O41 (Co2Z), demonstrating ferroelectricity induced by the complex internal alignment of magnetic moments. Further, both Co 2Z and Co2U have revealed observable magnetoelectric effects at room temperature, representing a step toward practical applications using the ME effect. These materials hold great potential for applications, since strong magnetoelectric coupling allows switching of the FE polarization with a magnetic field (H) and vice versa. These features could lead to a new type of storage devices, such as an electric field-controlled magnetic memory. A nanoscale-driven crystal growth of magnetic hexaferrites was successfully demonstrated at low growth temperatures (25--40% lower than the temperatures required often for crystal growth). This outcome exhibits thermodynamic processes of crystal growth, allowing ease in fabrication of advanced multifunctional materials. Most importantly, the

Crystal structure and magnetic properties of Cr doped barium hexaferrite

Science.gov (United States)

Kumar, Sunil; Supriya, Sweety; Pandey, Rabichandra; Pradhan, Lagen Kumar; Kar, Manoranjan

2018-04-01

The Cr3+ substituted BaFe12O19 has been synthesized by modified sol-gel method to tailor the magnetic anisotropy and coercivity for technological applications. Some basic studies have revealed that this substitution leads to unusual interactions among the magnetic sublattices of the M-type hexaferrite. In order to investigate these interactions, BaFe12-xCrxO19 (x = 0.0, 0.5, 1.0, 2.0, and 4.0) M-type hexaferrites were characterized by employing XRD (X-ray Diffractometer). It is confirmed that, all the samples are in nanocrystalline and single phase, no impurity has been detected within the XRD limit. The magnetic hysteresis (m-H) loops revealed the ferromagnetic nature of nanoparticles (NPs). The coercive field were increasing with the increasing Cr3+ content, but after the percolation limit it decreases. The magnetocrystalline anisotropy is increasing with the Cr3+ concentration in samples and high values of magnetocrystalline anisotropy revealed that all samples are hard magnetic materials. Magnetic hysteresis loops were analyzed using the Law of Approach to Saturation method.

Role of grain boundaries in the conduction of Eu–Ni substituted Y-type hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Ali, Irshad, E-mail: irshadalibzu@gmail.com [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Islam, M.U. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Naeem Ashiq, Muhammad, E-mail: naeemashiqqau@yahoo.com [Institute of Chemical Sciences, Bahauddin Zakariya University, Multan 60800 (Pakistan); Asif Iqbal, M. [National University of Sciences and Technology, EME College, Islamabad (Pakistan); Khan, Hasan M. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Murtaza, G. [Centre for Advanced Studies in Physics, Government College University, Lahore 54000 (Pakistan)

2014-08-01

Single phase nanostructured (Eu–Ni) substituted Y-type hexaferrites with nominal composition of Sr{sub 2}Co{sub 2−x}Ni{sub x}Eu{sub y}Fe{sub 12−y}O{sub 22} (x=0.0–1, y=0.0–0.1) were synthesized by the microemulsion method. Temperature dependent DC electrical conductivity and drift mobility were found in good agreement with each other, reflecting semiconducting behavior. The presence of Debye peaks in imaginary electric modulus curves confirmed the existence of relaxation phenomena in given frequency range. The AC conductivity follows power law, with exponent (n) value, ranges from 0.81–0.97, indicating that the mechanism is due to polaron hopping. In the present ferrite system, Cole–Cole plots were used to separate the grain and grain boundary effects. Eu–Ni substitution leads to a remarkable rise of grain boundary resistance as compared to the grain resistance. As both AC conductivity and Cole–Cole plots are the functions of concentration, they reveal the dominant contribution of grain boundaries in the conduction mechanism. It was also observed that the AC activation energy is lower than the DC activation energy. Appreciable improved values of quality factor suggested the possible use of these synthesized materials for power applications and high frequency multilayer chip inductors. - Highlights: • Single phase nanostructures were synthesized by the micro-emulsion method. • Substitution leads to a remarkable rise of grain boundary resistance. • The AC activation energy is lower than the DC activation energy. • Improved values of quality factor make these materials useful for high frequency multilayer chip inductors.

Crystal structure refinement, dielectric and magnetic properties of Ca/Pb substituted SrFe{sub 12}O{sub 19} hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Hooda, Ashima [Department of Physics, Deenbandhu Chhotu Ram University of Science and Technology, Murthal 131039, Haryana (India); Sanghi, Sujata, E-mail: sutkash@yahoo.com [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001, Haryana (India); Agarwal, Ashish [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001, Haryana (India); Dahiya, Reetu [Department of Physics, Hindu Girls College, Sonepat 131001, Haryana (India)

2015-08-01

SrFe{sub 12}O{sub 19} (SFO), Sr{sub 0.5}Ca{sub 0.5}Fe{sub 12}O{sub 19} (SCFO) and Sr{sub 0.5}Pb{sub 0.5}Fe{sub 12}O{sub 19} (SPFO) hexaferrites have been synthesized by a conventional solid state reaction technique. Powder X-ray diffraction and Rietveld refinement confirm the presence of M-type hexagonal phase in prepared samples. However in SCFO, secondary phase was also present with main phase. Analysis of Nyquist's plots of SFO hexaferrite revealed the contribution of many electrically active regions corresponding to bulk mechanism, distribution of grain boundaries and electrode processes also. Both conductivity and electric modulus formalisms have been employed to study the relaxation dynamics of charge carriers. A perfect overlapping of the normalized plots of modulus isotherms on a single ‘super curve’ for all the studied temperatures reveals a temperature independence of dynamic processes involved in conduction and for relaxation. In SPFO sample coercivity is reduced effectively but accompanied with increase in magnetization, which is requirement for hexaferrites to be used as magnetic recording media. - Highlights: • Samples have hexagonal phase with space group P6{sub 3}/mmc. • SPFO hexaferrite may be used for microwave devices. • SPFO hexaferrite may be used for magnetic recording media.

Minority anion substitution by Ni in ZnO

CERN Document Server

Pereira, Lino Miguel da Costa; Correia, João Guilherme; Amorim, Lígia Marina; Silva, Daniel José; David-Bosne, Eric; Decoster, Stefan; da Silva, Manuel Ribeiro; Temst, Kristiaan; Vantomme, André

2013-01-01

We report on the lattice location of implanted Ni in ZnO using the $\\beta$− emission channeling technique. In addition to the majority substituting for the cation (Zn), a significant fraction of the Ni atoms occupy anion (O) sites. Since Ni is chemically more similar to Zn than it is to O, the observed O substitution is rather puzzling. We discuss these findings with respect to the general understanding of lattice location of dopants in compound semiconductors. In particular, we discuss potential implications on the magnetic behavior of transition metal doped dilute magnetic semiconductors.

Synthesis and electrical behavior of Ni-Ti substituted Y-type hexaferrites for high frequency application

Science.gov (United States)

Ahmad, Bashir; Ashiq, Muhammad Naeem; Mumtaz, Saleem; Ali, Irshad; Najam-Ul-Haq, Muhmmad; Sadiq, Imran

2018-04-01

This article reports the fabrication of Ni-Ti doped derivatives of Sr2Co2Fe12-2xO22 by economical Sol-gel method. At room temperature X-ray diffraction (XRD) pattern of powder was obtained after sintering at 1050 °C. The XRD analysis revealed the formation of pure Sr-Y hexaferrite phase. It was found that the observed values of dielectric parameters decreased with increasing Ni-Ti substitution. The higher values of dielectric constants and dielectric loss factor at lower frequency were owing to surface charge polarization. In all the samples the resonance peaks were also observed. The observed room temperature DC electrical resistivity found to increase from 1.8x106 to 4.9x109 ohm cm. The observed activation energies values of the fabricated materials are found in 0.52-0.82 eV range. The decrease in dielectric parameters and increase in resistivity of the fabricated samples with substituents suggest these materials have worth application in micro-wave devices as such devices required highly resistive materials.

Site occupancy and magnetic properties of Al-substituted M-type strontium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Dixit, Vivek; Nandadasa, Chandani N.; Kim, Seong-Gon, E-mail: kimsg@ccs.msstate.edu [Department of Physics and Astronomy, Mississippi State University, Mississippi State, Mississippi 39762 (United States); Center for Computational Sciences, Mississippi State University, Mississippi State, Mississippi 39762 (United States); Kim, Sungho [Center for Computational Sciences, Mississippi State University, Mississippi State, Mississippi 39762 (United States); Park, Jihoon; Hong, Yang-Ki [Department of Electrical and Computer Engineering and MINT Center, The University of Alabama, Tuscaloosa, Alabama 35487 (United States); Liyanage, Laalitha S. I. [Department of Physics, University of North Texas, Denton, Texas 76203 (United States); Moitra, Amitava [Thematic Unit of Excellence on Computational Materials Science, S.N. Bose National Centre for Basic Sciences, Sector-III, Block-JD, Salt Lake, Kolkata-700098 (India)

2015-06-28

We use first-principles total-energy calculations based on density functional theory to study the site occupancy and magnetic properties of Al-substituted M-type strontium hexaferrite SrFe{sub 12−x}Al{sub x}O{sub 19} with x = 0.5 and x = 1.0. We find that the non-magnetic Al{sup 3+} ions preferentially replace Fe{sup 3+} ions at two of the majority spin sites, 2a and 12k, eliminating their positive contribution to the total magnetization causing the saturation magnetization M{sub s} to be reduced as Al concentration x is increased. Our formation probability analysis further provides the explanation for increased magnetic anisotropy field when the fraction of Al is increased. Although Al{sup 3+} ions preferentially occupy the 2a sites at a low temperature, the occupation probability of the 12k site increases with the rise of the temperature. At a typical annealing temperature (>700 °C) Al{sup 3+} ions are much more likely to occupy the 12k site than the 2a site. Although this causes the magnetocrystalline anisotropy K{sub 1} to be reduced slightly, the reduction in M{sub s} is much more significant. Their combined effect causes the anisotropy field H{sub a} to increase as the fraction of Al is increased, consistent with recent experimental measurements.

The thermal stability range and magnetic properties of U-type hexaferrites

International Nuclear Information System (INIS)

Lisjak, Darja; Drofenik, Miha

2004-01-01

Single-phase polycrystalline U-hexaferrites with the composition Ba 4 A 2 Fe 36 O 60 (A=Co, Ni, Zn) were prepared by solid-state reaction synthesis employing high-energy milling or topotactic reaction and calcination at 1200-1300 deg. C. The Curie temperature and saturation magnetization of the samples were influenced by the composition, while the coercivity was more strongly influenced by the preparation conditions

Synthesis and properties of nickel-doped nanocrystalline barium hexaferrite ceramic materials

Science.gov (United States)

Waqar, Moaz; Rafiq, Muhammad Asif; Mirza, Talha Ahmed; Khalid, Fazal Ahmad; Khaliq, Abdul; Anwar, Muhammad Sabieh; Saleem, Murtaza

2018-04-01

M-type barium hexaferrite ceramics have emerged as important materials both for technological and commercial applications. However, limited work has been reported regarding the investigation of nanocrystalline Ni-doped barium hexaferrites. In this study, nanocrystalline barium hexaferrite ceramics with the composition BaFe12- x Ni x O19 (where x = 0, 0.3 and 0.5) were synthesized by sol-gel method and characterized using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, vibrating sample magnetometer and precision impedance analyzer. All the synthesized samples had single magnetoplumbite phase having space group P63/mmc showing the successful substitution of Ni in BaFe12O19 without the formation of any impurity phase. Average grain size of undoped samples was around 120 nm which increased slightly with the addition of Ni. Saturation magnetization ( M s) and remnant magnetization ( M r) increased with the addition of Ni, however, coercivity ( H c) decreased with the increase in Ni from x = 0 to x = 0.5. Real and imaginary parts of permittivity decreased with the increasing frequency and increased with Ni content. Dielectric loss and conductivity showed slight variation with the increase in Ni concentration.

Structural and magnetic properties of Nd–Mn substituted Y-type hexaferrites synthesized by microemulsion method

International Nuclear Information System (INIS)

Murtaza, G.; Ahmad, R.; Hussain, T.; Ayub, R.; Ali, Irshad; Khan, Muhammad Azhar; Akhtar, Majid Niaz

2014-01-01

Highlights: • Synthesis via a chemical route microemulsion method. • Samples were characterized with XRD, SEM, AFM, FTIR, Dielectric Measurements and VSM. • Single phase patterns were recorded. • A marked decrease in coercivity has been observed with the substitution of Nd–Mn. • These ferrites are suitable for multi-layer chip components in hyper-frequency. - Abstract: Nd–Mn substituted hexaferrites of composition Sr 2−x Nd x Ni 0.5 Co 1.5 Fe 12−y Mn y O 22 (x = 0.0, 0.02, 0.04, 0.06, 0.08, 0.10, 0.20, 0.30, y = 0.0, 0.25, 0.50, 0.75, 1.00, 1.25, 1.50, 1.75) were synthesized using microemulsion method. The synthesized materials are characterized using different techniques including X-ray diffraction (XRD), scanning electron microscopy(SEM), atomic force microscopy (AFM), Fourier transform Infrared spectroscopy (FTIR), Inductance capacitance resistance (LCR) meter and Vibrating sample magnetic magnetometer (VSM). For all samples, a single Y-type phase was established and the lattice constants have been calculated. XRD patterns reveal the significant increase in line broadening which indicates a decrease of grain size. The samples exhibit well defined crystallization; all of them are hexagonal platelet grains. With the increasing substitution level of Nd–Mn, the average grain diameter decreases. The dielectric constant ε ′ and dielectric loss factor ε″ are found to decrease initially with an increase in frequency and reached a constant value at higher frequency, exhibiting a frequency-independent behavior at higher frequencies. The dielectric loss tangent tanδ was found to decrease with an increase in the frequency. The H c decreases remarkably with increasing Nd and Mn ions content. It was found that the particle size could be effectively decreased and coercivity H c could easily be controlled by varying the concentration (x) without significantly decreasing saturation magnetization

Structural and magnetic properties of Nd–Mn substituted Y-type hexaferrites synthesized by microemulsion method

Energy Technology Data Exchange (ETDEWEB)

Murtaza, G., E-mail: gm_rai786@yahoo.com [Centre for Advanced Studies in Physics, Government College University, Lahore 54000 (Pakistan); Ahmad, R.; Hussain, T.; Ayub, R. [Centre for Advanced Studies in Physics, Government College University, Lahore 54000 (Pakistan); Ali, Irshad [Department of Physics, Bahauddin Zakariya University, Multan (Pakistan); Khan, Muhammad Azhar [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Akhtar, Majid Niaz [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan)

2014-07-25

Highlights: • Synthesis via a chemical route microemulsion method. • Samples were characterized with XRD, SEM, AFM, FTIR, Dielectric Measurements and VSM. • Single phase patterns were recorded. • A marked decrease in coercivity has been observed with the substitution of Nd–Mn. • These ferrites are suitable for multi-layer chip components in hyper-frequency. - Abstract: Nd–Mn substituted hexaferrites of composition Sr{sub 2−x}Nd{sub x}Ni{sub 0.5}Co{sub 1.5}Fe{sub 12−y}Mn{sub y}O{sub 22} (x = 0.0, 0.02, 0.04, 0.06, 0.08, 0.10, 0.20, 0.30, y = 0.0, 0.25, 0.50, 0.75, 1.00, 1.25, 1.50, 1.75) were synthesized using microemulsion method. The synthesized materials are characterized using different techniques including X-ray diffraction (XRD), scanning electron microscopy(SEM), atomic force microscopy (AFM), Fourier transform Infrared spectroscopy (FTIR), Inductance capacitance resistance (LCR) meter and Vibrating sample magnetic magnetometer (VSM). For all samples, a single Y-type phase was established and the lattice constants have been calculated. XRD patterns reveal the significant increase in line broadening which indicates a decrease of grain size. The samples exhibit well defined crystallization; all of them are hexagonal platelet grains. With the increasing substitution level of Nd–Mn, the average grain diameter decreases. The dielectric constant ε{sup ′} and dielectric loss factor ε″ are found to decrease initially with an increase in frequency and reached a constant value at higher frequency, exhibiting a frequency-independent behavior at higher frequencies. The dielectric loss tangent tanδ was found to decrease with an increase in the frequency. The H{sub c} decreases remarkably with increasing Nd and Mn ions content. It was found that the particle size could be effectively decreased and coercivity H{sub c} could easily be controlled by varying the concentration (x) without significantly decreasing saturation magnetization.

Arsenic in ZnO and GaN: substitutional cation or anion sites?

CERN Document Server

Wahl, Ulrich; Rita, Elisabete; Marques, Ana Claudia; Alves, Eduardo; Carvalho Soares, José

2007-01-01

We have determined the lattice location of ion implanted As in ZnO and GaN by means of conversion electron emission channeling from radioactive $^{73}$As. In contrast to what one might expect from its nature as a group V element, we find that As does not occupy substitutional O sites in ZnO but in its large majority substitutional Zn sites. Arsenic in ZnO is thus an interesting example for an impurity in a semiconductor where the major impurity lattice site is determined by atomic size and electronegativity rather than its position in the periodic system. In contrast, in GaN the preference of As for substitutional cation sites is less pronounced and about half of the implanted As atoms occupy Ga and the other half N sites. Apparently, the smaller size-mismatch between As and N and the chemical similarity of both elements make it feasible that As partly substitutes for N atoms.

Ab initio understanding of magnetic properties in Zn2+ substitution of Fe3O4 ultra-thin film with dilute Zn substitution

Science.gov (United States)

Huang, Zhaocong; Chen, Qian; Jiang, Sheng; Dong, Shuai; Zhai, Ya

2018-05-01

The mechanism of the magnetic properties on the Zn2+ substituted Fe3O4 film have been investigated based on first principle calculations. It is found that the surface effect plays an important role in the occupation of Zn ion, and in turn changes the magnetic moment. It may also destroy the half metallic behavior of Fe3O4 film even if the Zn2+ concentration only is one Zn2+ per unit cell (4%), which is different from that in bulk material.

Synthesis of Zn{sup 2+} substituted maghemite nanoparticles and investigation of their structural and magnetic properties

Energy Technology Data Exchange (ETDEWEB)

Mozaffari, M. [Department of Physics, Faculty of Science, University of Isfahan, Isfahan 81746-73441 (Iran, Islamic Republic of); Shatooti, S. [Department of Physics, Razi University, Kermanshah 67149-67346 (Iran, Islamic Republic of); Jafarzadeh, M., E-mail: mjafarzadeh1027@yahoo.com [Faculty of Chemistry, Razi University, Kermanshah 67149-67346 (Iran, Islamic Republic of); Niyaifar, M. [Department of Physics, Ahvaz Branch, Islamic Azad University, Ahvaz (Iran, Islamic Republic of); Aftabi, A. [Department of Physics, University of Kurdistan, Sanandaj 66177-15175 (Iran, Islamic Republic of); Mohammadpour, H. [Department of Physics, Ahvaz Branch, Islamic Azad University, Ahvaz (Iran, Islamic Republic of); Amiri, Sh. [Department of Physics, Razi University, Kermanshah 67149-67346 (Iran, Islamic Republic of)

2015-05-15

Maghemite and Zn{sup 2+} substituted maghemite (γ-Fe{sub 2−y} Zn{sub 3y/2}O{sub 3}, y=0.0, 0.11, 0.24, 0.36, 0.50 and 0.66) nanoparticles were prepared by coprecipitation method. The effect of Zn{sup 2+} substitution on the structural, morphological and magnetic properties of the nanoparitcles were studied by different techniques such as X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), magnetometry, magnetic thermogravimetry and Mössbauer spectroscopy. The results of XRD showed that all samples have spinel structure with an increase in lattice parameter by increasing the content of Zn{sup 2+}. FTIR spectra were proved the synthesis of maghemite and Zn{sup 2+} substituted maghemite with appearance of the related absorption bands and band shift upon Zn{sup 2+} substitution. Morphological studies by FESEM demonstrated that the nanoparticles were uniform and spherical with average particle size in range of 20–24 nm. Room temperature magnetic measurements showed that as Zn{sup 2+} content increases, saturation magnetization initially increase up to 75.34 emu/g for y=0.11 and then decrease to 3.65 emu/g for y=0.66, due to substitution of magnetic Fe{sup 3+} by non-magnetic Zn{sup 2+}. Decrease in Curie temperature of the samples, from 510 for maghemite to 250 °C for y=0.36, by increasing the Zn{sup 2+} substitution was a result of reduction of superexchange interactions between different sites. Then, the Curie temperature increased up to 680 °C for y=0.66 which was due to migration of some Zn{sup 2+} ions from A to B sites in the structure of spinel. Room temperature Mössbauer spectra exhibited that the sample with y=0.0 was superparamagnetic, while by increasing the content of Zn{sup 2+}, relaxation effect increased by weakening of A–B exchange interaction. - Highlights: • Synthesis of Zn{sup 2+}-substituted maghemite via co-precipitation/oxidation method. • Increase in lattice

Improvement of the performance of microwave X band absorbers based on pure and doped Ba-hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Seyyed Afghahi, Seyyed Salman [Department of Materials Science and Engineering, Imam Hossein University, Tehran (Iran, Islamic Republic of); Jafarian, Mojtaba, E-mail: m.jafarian@srbiau.ac.ir [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Salehi, Mohsen [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Atassi, Yomen [Department of Applied Physics, Higher Institute for Applied Sciences and Technology, Damascus (Syrian Arab Republic)

2017-01-01

Optimum Fe/Ba mole ratio is determined in doped Ba-hexaferrite prepared via mechanical activation. X-ray diffractometer (XRD), scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and vector network analyzer are used to analyze phases, structures, electromagnetic and microwave absorption properties. The mole ratio of Fe/Ba=10 is detected to be optimum for doping and synthesizing the Ba-hexaferrite. In order to achieve high absorption in X band the ions of Zr{sup 4+}–Sn{sup 4+}–Ti{sup 4+}–M{sup 2+} (M=Mg{sup 2+}, Zn{sup 2+}, Cu{sup 2+}, Co{sup 2+}) are used as dopants. The results indicate the formation of single phase Ba-hexaferrite in either pure or doped compounds without any non-magnetic intermediate phases and with spherical and hexagonal morphologies respectively for the pure and doped ferrite. It is found out that BaCo{sub 2}Zr(SnTi){sub 0.5}Fe{sub 8}O{sub 19} compound has the maximum saturation magnetization (49.80 emu/g). Also the composite of BaCo{sub 2}Zr(SnTi){sub 0.5}Fe{sub 8}O{sub 19} 50 wt% in epoxy resin exhibits a minimum reflection loss of −29 dB at 12.2 GHz with 2.6 GHz bandwidth. - Highlights: • Optimum Fe/Ba mole ratio is determined in doped Ba-hexaferrite. • Formation of a single phase M-hexaferrite, pure or doped when Fe/Ba=10. • Preparation of microwave absorber of BaCo{sub 2}Zr(SnTi){sub 0.5}Fe{sub 8}O{sub 19}/epoxy resin, 50 wt%. • The absorber exhibits a minimum RL of −29 dB at 12.2 GHz with 2.6 GHz bandwidth.

Effect of precursor choice and sintering conditions for W hexaferrite formation

DEFF Research Database (Denmark)

Mørch, Mathias; Eikeland, Anna; Christensen, Mogens

. Hexaferrites are of great interest because of high stability, high anisotropy and favorable cost/performance ratio. This work focuses on the W-phase hexaferrite which excels with its high anisotropy constant, Curie temperature, and a higher saturation magnetization compared to other hexaferrites...

Mössbauer studies of Sn /Nb substituted Mn–Zn ferrites

Indian Academy of Sciences (India)

Unknown

communications, devices like computers, microprocessor and VCR systems, the use of above said types of power supplies highly increased. Though studies on Mn–Zn ... Hence, the aim of the present paper is to bring out the. Mössbauer studies of Sn/Nb substituted Mn–Zn ferrites. 2. Sample preparation and experimental.

Defect dynamics in Li substituted nanocrystalline ZnO: A spectroscopic analysis

International Nuclear Information System (INIS)

Ghosh, S.; Nambissan, P.M.G.; Thapa, S.; Mandal, K.

2014-01-01

Very recently, vacancy-type defects have been found to play a major role in stabilizing d 0 ferromagnetism in various low dimensional ZnO systems. In this context, the evolution of vacancy-type defects within the ZnO nanocrystals due to the doping of ZnO by alkali metal lithium (Li) is investigated using X-ray photoelectron (XPS), photoluminescence (PL) and positron annihilation spectroscopy (PAS). Li-doping is found to have significant effects in modifying the vacancy-type defects, especially the Zn vacancy (V Zn ) defects within the ZnO lattice. XPS measurement indicated that initially the Li 1+ ions substitute at Zn 2+ sites, but when Li concentration exceeds 7 at%, excess Li starts to move through the interstitial sites. The increase in positron lifetime components and the lineshape S-parameter obtained from coincident Doppler broadening spectra with Li-doping indicated an enhancement of V Zn defect concentration within the doped ZnO lattice. The vacancy type defects, initially of the predominant configuration V Zn+O+Zn got reduced to neutral ZnO divacancies due to the partial recombination by the doped Li 1+ ions but, when the doping concentration exceeded 7 at% and Li 1+ ions started migrating to the interstitials, positron diffusion is partly impeded and this results in reduced probability of annihilation. PL spectra have shown intense green and yellow-orange emission due to the stabilization of a large number of V Zn defects and Li substitutional (Li Zn ) defects respectively. Hence Li can be a very useful dopant in stabilizing and modifying significant amount of Zn vacancy-defects which can play a useful role in determining the material behavior

Low-loss Z-type barium hexaferrite composites from nanoscale ZnAl2O4 addition for high-frequency applications

Science.gov (United States)

Zheng, Zongliang; Feng, Quanyuan; Harris, Vincent G.

2018-05-01

In this study, nanocrystalline ZnAl2O4 (ZA) were introduced to Z-type barium hexaferrite (Co2Z) and the effects of ZA addition upon the crystal-phase composition, microstructure, permeability and permittivity as well as losses characteristics over a wide frequency range of 10 MHz-1 GHz have been systematically investigated. With increasing ZA content (x) from 0 to 15 wt%, the permeability μ' at low frequencies decreased from 12.0 to 4.3, while the permittivity ɛ' was decreased from 27.4 to 10.7. Correspondingly, the frequency stability of permeability and permittivity were improved and the losses were effectively reduced. When x is in the range of 5-10 wt%, the magnetic loss tan δμ is in the order of 10-2 and the dielectric loss tan δɛ is in the order of 10-3 at 300 MHz, which is lower by one order of magnitude compared with that of undoped Co2Z. The modified magnetic and dielectric properties are closely related to the changing phase composition and microstructure.

Influence of La3+ Substitution on Structure, Morphology and Magnetic Properties of Nanocrystalline Ni-Zn Ferrite.

Directory of Open Access Journals (Sweden)

Y K Dasan

Full Text Available Lanthanum substituted Ni-Zn ferrite nanoparticles (Ni0.5Zn0.5LaxFe1-xO4; 0.00 ≤x≤ 1.00 synthesized by sol-gel method were presented. X-ray diffraction patterns reveal the typical single phase spinel cubic ferrite structure, with the traces of secondary phase for lanthanum substituted nanocrystals. In addition, the structural analysis also demonstrates that the average crystallite size varied in the range of 21-25 nm. FTIR spectra present the two prominent absorption bands in the range of 400 to 600 cm-1 which are the fingerprint region of all ferrites. Surface morphology of both substituted and unsubstituted Ni-Zn ferrite nanoparticle samples was studied using FESEM technique and it indicates a significant increase in the size of spherical shaped particles with La3+ substitution. Magnetic properties of all samples were analyzed using vibrating sample magnetometer (VSM. The results revealed that saturation magnetization (Ms and coercivity (Hc of La3+ substituted samples has decreased as compared to the Ni-Zn ferrite samples. Hence, the observed results affirm that the lanthanum ion substitution has greatly influenced the structural, morphology and magnetic properties of Ni-Zn ferrite nanoparticles.

Defect dynamics in Li substituted nanocrystalline ZnO: A spectroscopic analysis

Energy Technology Data Exchange (ETDEWEB)

Ghosh, S., E-mail: sghoshphysics@gmail.com [Department of Material Science, Indian Association for the Cultivation of Science, 2A and 2B Raja S.C. Mullick Road, Jadavpur, Kolkata 700032 (India); Nambissan, P.M.G.; Thapa, S. [Applied Nuclear Physics Division, Saha Institute of Nuclear Physics, Sector 1, Block AF, Bidhannagar, Kolkata 700064 (India); Mandal, K. [Department of Condensed Matter Physics and Material Sciences, S.N. Bose National Centre for Basic Sciences, Block JD, Sector III, Salt Lake, Kolkata 700098 (India)

2014-12-01

Very recently, vacancy-type defects have been found to play a major role in stabilizing d{sup 0} ferromagnetism in various low dimensional ZnO systems. In this context, the evolution of vacancy-type defects within the ZnO nanocrystals due to the doping of ZnO by alkali metal lithium (Li) is investigated using X-ray photoelectron (XPS), photoluminescence (PL) and positron annihilation spectroscopy (PAS). Li-doping is found to have significant effects in modifying the vacancy-type defects, especially the Zn vacancy (V{sub Zn}) defects within the ZnO lattice. XPS measurement indicated that initially the Li{sup 1+} ions substitute at Zn{sup 2+} sites, but when Li concentration exceeds 7 at%, excess Li starts to move through the interstitial sites. The increase in positron lifetime components and the lineshape S-parameter obtained from coincident Doppler broadening spectra with Li-doping indicated an enhancement of V{sub Zn} defect concentration within the doped ZnO lattice. The vacancy type defects, initially of the predominant configuration V{sub Zn+O+Zn} got reduced to neutral ZnO divacancies due to the partial recombination by the doped Li{sup 1+} ions but, when the doping concentration exceeded 7 at% and Li{sup 1+} ions started migrating to the interstitials, positron diffusion is partly impeded and this results in reduced probability of annihilation. PL spectra have shown intense green and yellow-orange emission due to the stabilization of a large number of V{sub Zn} defects and Li substitutional (Li{sub Zn}) defects respectively. Hence Li can be a very useful dopant in stabilizing and modifying significant amount of Zn vacancy-defects which can play a useful role in determining the material behavior.

Defect dynamics in Li substituted nanocrystalline ZnO: A spectroscopic analysis

Science.gov (United States)

Ghosh, S.; Nambissan, P. M. G.; Thapa, S.; Mandal, K.

2014-12-01

Very recently, vacancy-type defects have been found to play a major role in stabilizing d0 ferromagnetism in various low dimensional ZnO systems. In this context, the evolution of vacancy-type defects within the ZnO nanocrystals due to the doping of ZnO by alkali metal lithium (Li) is investigated using X-ray photoelectron (XPS), photoluminescence (PL) and positron annihilation spectroscopy (PAS). Li-doping is found to have significant effects in modifying the vacancy-type defects, especially the Zn vacancy (VZn) defects within the ZnO lattice. XPS measurement indicated that initially the Li1+ ions substitute at Zn2+ sites, but when Li concentration exceeds 7 at%, excess Li starts to move through the interstitial sites. The increase in positron lifetime components and the lineshape S-parameter obtained from coincident Doppler broadening spectra with Li-doping indicated an enhancement of VZn defect concentration within the doped ZnO lattice. The vacancy type defects, initially of the predominant configuration VZn+O+Zn got reduced to neutral ZnO divacancies due to the partial recombination by the doped Li1+ ions but, when the doping concentration exceeded 7 at% and Li1+ ions started migrating to the interstitials, positron diffusion is partly impeded and this results in reduced probability of annihilation. PL spectra have shown intense green and yellow-orange emission due to the stabilization of a large number of VZn defects and Li substitutional (LiZn) defects respectively. Hence Li can be a very useful dopant in stabilizing and modifying significant amount of Zn vacancy-defects which can play a useful role in determining the material behavior.

Electromagnetic behavior of radar absorbing materials based on Ca hexaferrite modified with Co-Ti ions and doped with La

Directory of Open Access Journals (Sweden)

Valdirene Aparecida da Silva

2009-06-01

Full Text Available Radar Absorbing Materials (RAM are compounds that absorb incidental electromagnetic radiation in tuned frequencies and dissipate it as heat. Its preparation involves the adequate processing of polymeric matrices filled with compounds that act as radar absorbing centers in the microwave range. This work shows the electromagnetic evaluation of RAM based on CoTi and La doped Ca hexaferrite. Vibrating Sample Magnetization analyses show that ion substitution promoted low values for the parameters of saturation magnetization (123.65 Am2/kg and coercive field (0.07 T indicating ferrite softening. RAM samples obtained using different hexaferrite concentrations (40-80 per cent, w/w show variations in complex permeability and permittivity parameters and also in the performance of incidental radiation attenuation. Microwave attenuation values between 40 and 98 per cent were obtained.

Moessbauer spectroscopic determination of magnetic moments of Fe3+ and Co2+ in substituted barium hexaferrite, Ba(Co,Ti)xFe(12-2x)O19

International Nuclear Information System (INIS)

Williams, J.M.; Adetunji, J.; Gregori, M.

2000-01-01

We report the distribution of magnetic moments of Fe 3+ and Co 2+ in Co 2+ -, Ti 4+ -substituted M-type barium hexaferrite, Ba(Co,Ti) x Fe (12-2x) O 19 , as a function of doping rate, x. The substitution, x, for iron has been varied with x=0, 0.25, 0.50, 0.70 and 0.85. The magnetic moments of Fe 3+ and Co 2+ were calculated from the combined results of Moessbauer measurements for Fe 3+ ions in the sublattices and neutron diffraction data for the total moments of Fe 3+ and Co 2+ . A comparison of the signs of the magnetic moments of Fe 3+ and Co 2+ ions enabled us to attribute spin directions of the Co 2+ ions in the sublattices of the substituted ferrite samples. The spin directions of Co 2+ are opposite to those of Fe 3+ in the 4f 2 and 2b sublattices. They are reversed from the original directions in the 4f 1 and 12K sublattices when the value of x≥0.70. A quantitative analysis shows that Co 2+ and Ti 4+ ions are preferably substituted into 4f 2 and 12K sublattices, respectively. In addition, while the hyperfine field of Fe 3+ in the 2b sublattice gives rise to the 2b-4f 2 interaction it is the partially substituted Co 2+ ions in the 4f 1 and 12K sublattices that contribute to the near neighbour 2a-4f 1 and 2b-12K types of interaction

Structural and magnetic properties of barium-gadolinium hexaferrites

Science.gov (United States)

Litsardakis, G.; Manolakis, I.; Serletis, C.; Efthimiadis, K. G.

A series of Gd-substituted M-type barium hexaferrites has been prepared by the ceramic route, according to the formula (Ba 1-xGd x)O·5.25Fe 2O 3 ( x=0-0.30). XRD analysis revealed that all the samples present primarily an M-type structure. Samples x=0 and x=0.05 are single-phase. Hematite (Fe 2O 3) and GdFeO 3 were detected in the remaining samples. Coercivity ( Hc) shows remarkably high values, ˜293 kA/m for x=0.20 and 0.30 with a maximum of 322 kA/m for x=0.25. Specific saturation magnetization ( σsat) of the samples presents a small increase up to x=0.10. The microstructure examination indicates that Gd may act as a grain growth inhibitor.

Mixed Zn and O substitution of Co and Mn in ZnO

CERN Document Server

Pereira, Lino Miguel da Costa; Decoster, Stefan; Correia, João Guilherme; Amorim, Lígia Marina; da Silva, Manuel Ribeiro; Araújo, João Pedro; Vantomme, André

2011-01-01

The physical properties of an impurity atom in a semiconductor are primarily determined by the lattice site it occupies. In general, this occupancy can be correctly predicted based on chemical intuition, but not always. We report on one such exception in the dilute magnetic semiconductors Co- and Mn-doped ZnO, experimentally determining the lattice location of Co and Mn using $\\beta$-emission channeling from the decay of radioactive $^{61}$Co and $^{56}$Mn implanted at the ISOLDE facility at CERN. Surprisingly, in addition to the majority substituting for Zn, we find up to 18% (27%) of the Co (Mn) atoms in O sites, which is virtually unaffected by thermal annealing up to 900 °C. We discuss how this anion site configuration, which had never been considered before for any transition metal in any metal oxide material, may in fact have a low formation energy. This suggests a change in paradigm regarding transition-metal incorporation in ZnO and possibly other oxides and wide-gap semiconductors.

Thin Bioactive Zn Substituted Hydroxyapatite Coating Deposited on Ultrafine Grained Titanium Substrate: Structure Analysis

Science.gov (United States)

Prosolov, Konstantin A.; Belyavskaya, Olga A.; Muehle, Uwe; Sharkeev, Yurii P.

2018-02-01

Nanocrystalline Zn substituted hydroxyapatite coatings were deposited by radiofrequency magnetron sputtering on the surface of ultrafine-grained titanium substrates. Cross section transmission electron microscopy provided information about the morphology and texture of the thin film while in-column energy dispersive X-ray analysis confirmed the presence of Zn in the coating. The Zn substituted hydroxyapatite coating was formed by an equiaxed polycrystalline grain structure. Effect of substrate crystallinity on the structure of deposited coating is discussed. An amorphous TiO2 sublayer of 8 nm thickness was detected in the interface between the polycrystalline coating and the Ti substrate. Its appearance in the amorphous state is attributed to prior to deposition etching of the substrate and subsequent condensation of oxygen-containing species sputtered from the target. This layer contributes to the high coating-to-substrate adhesion. The major P-O vibrational modes of high intensity were detected by Raman spectroscopy. The Zn substituted hydroxyapatite could be a material of choice when antibacterial osteoconductive coating with a possibility of withstanding mechanical stress during implantation and service is needed.

Thin Bioactive Zn Substituted Hydroxyapatite Coating Deposited on Ultrafine-Grained Titanium Substrate: Structure Analysis

Directory of Open Access Journals (Sweden)

Konstantin A. Prosolov

2018-02-01

Full Text Available Nanocrystalline Zn-substituted hydroxyapatite coatings were deposited by radiofrequency magnetron sputtering on the surface of ultrafine-grained titanium substrates. Cross-section transmission electron microscopy provided information about the morphology and texture of the thin film while in-column energy dispersive X-ray analysis confirmed the presence of Zn in the coating. The Zn-substituted hydroxyapatite coating was formed by an equiaxed polycrystalline grain structure. Effect of substrate crystallinity on the structure of deposited coating is discussed. An amorphous TiO2 sublayer of 8-nm thickness was detected in the interface between the polycrystalline coating and the Ti substrate. Its appearance in the amorphous state is attributed to prior to deposition etching of the substrate and subsequent condensation of oxygen-containing species sputtered from the target. This layer contributes to the high coating-to-substrate adhesion. The major P–O vibrational modes of high intensity were detected by Raman spectroscopy. The Zn-substituted hydroxyapatite could be a material of choice when antibacterial osteoconductive coating with a possibility of withstanding mechanical stress during implantation and service is needed.

Radiation losses in microwave K_u region by conducting pyrrole/barium titanate and barium hexaferrite based nanocomposites

International Nuclear Information System (INIS)

Kaur, Talwinder; Kumar, Sachin; Narang, S.B.; Srivastava, A.K.

2016-01-01

Nanocomposites of substituted barium hexaferrite and barium titanate embedded in a polymer were synthesized via emulsion polymerization. The study was performed by using X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, electron spin resonance spectroscopy, a vibrating sample magnetometer and a vector network analyzer. It is found that maximum radiation loss occur at 16.09 GHz (−14.23 dB) frequency owing to the combined effect of conducting polymer, suitable dielectric and magnetic material. This suggests that prepared material is suitable for radiation losses. Micro structural study reveals the presence of all the phases of the compounds comprises composite. Benzene ring absorption band (at 1183 cm"−"1) in FT-IR spectra illustrates the presence of polymer. Surface morphology reveals the presence of array of particles encapsulated by the polymer. - Highlights: • Composites having polymer, barium titanate and hexaferrite have been successfully prepared. • Effective radiation absorption and losses have been achieved. • Magnetic properties have made an impact on shielding effectiveness.

Preparation of strontium hexaferrite magnets from celestite and blue dust by mechanochemical route

Directory of Open Access Journals (Sweden)

Tiwary R.K.

2008-01-01

Full Text Available In the present investigation celestite (natural ore of strontium and blue dust (iron ore fines have been used for the preparation of strontium hexaferrite powder. The mechanical alloying process has been adopted to prepare strontium hexaferrite powder. The celestite after chemical upradation and physically upgraded blue dust alongwith sodium carbonate was taken for the preparation of strontium hexaferrite in this experiment. The high-energy planetary ball mill with tungsten carbide jar and ball was used to prepare strontium hexaferrite powder. A long time of ball milling for different duration has led to displacement solid-state reaction. At the end of each experiment the product was washed thoroughly and dried. The X-ray diffaction study after annealing shows the development of single-phase strontium hexaferrite after 40 hrs. of milling. The resultant powder was compacted under magnetic field and sintered to prepare the magnet after annealing the ferrite powder. The magnetic properties were measured by Pulse magneto meter. The moderate value of coercivity, remanence and energy product were observed in this sintered magnet. The work illustrates the feasibility to prepare strontium hexaferrite magnetic powders directly from natural ores which can reduce the total cost of production as compared to conventional method.

Radiation losses in microwave K{sub u} region by conducting pyrrole/barium titanate and barium hexaferrite based nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Kaur, Talwinder [Department of Physics, Lovely Professional University, Phagwara 144411 (India); Kumar, Sachin [Department of Chemistry, Guru Nanak Dev University, Amritsar 143005 (India); Narang, S.B. [Department of Electronics Technology, Guru Nanak Dev University, Amritsar 143005 (India); Srivastava, A.K., E-mail: srivastava_phy@yahoo.co.in [Department of Physics, Lovely Professional University, Phagwara 144411 (India)

2016-12-15

Nanocomposites of substituted barium hexaferrite and barium titanate embedded in a polymer were synthesized via emulsion polymerization. The study was performed by using X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy, electron spin resonance spectroscopy, a vibrating sample magnetometer and a vector network analyzer. It is found that maximum radiation loss occur at 16.09 GHz (−14.23 dB) frequency owing to the combined effect of conducting polymer, suitable dielectric and magnetic material. This suggests that prepared material is suitable for radiation losses. Micro structural study reveals the presence of all the phases of the compounds comprises composite. Benzene ring absorption band (at 1183 cm{sup −1}) in FT-IR spectra illustrates the presence of polymer. Surface morphology reveals the presence of array of particles encapsulated by the polymer. - Highlights: • Composites having polymer, barium titanate and hexaferrite have been successfully prepared. • Effective radiation absorption and losses have been achieved. • Magnetic properties have made an impact on shielding effectiveness.

Photovoltaic Performance of ZnO Nanosheets Solar Cell Sensitized with Beta-Substituted Porphyrin

Directory of Open Access Journals (Sweden)

Arumugam Mahesh

2011-01-01

Full Text Available The photoanode of dye-sensitized solar cell (DSSC was fabricated using two-dimensional ZnO nanosheets (2D ZnO NSs sensitized with beta-substituted porphyrins photosensitizer, and its photovoltaic performance in solid-state DSSC with TiO2 nanotubes (TiO2 TNs modified poly (ethylene oxide (PEO polymer electrolyte was studied. The ZnO NSs were synthesized through hydrothermal method and were characterized through high-resolution scanning electron microscopy (HRSEM, diffused reflectance spectra (DRS, photoluminescence spectra (PL, and X-ray diffraction (XRD analysis. The crystallinity of the polymer electrolytes was investigated using X-ray diffraction analysis. The photovoltaic performance of the beta-substituted porphyrins sensitized solar cells was evaluated under standard AM1.5G simulated illumination (100 mW cm−2. The efficiency of energy conversion from solar to electrical due to 2D ZnO NSs based DSSCs is 0.13%, which is about 1.6 times higher than that of the control DSSC using ZnO nanoparticles (ZnO NPs as photoanode (0.08%, when TiO2 NTs fillers modified PEO electrolyte was incorporated in the DSSCs. The current-voltage (- and photocurrent-time (- curves proved stable with effective collection of electrons, when the 2D ZnO nanostructured photoanode was introduced in the solid-state DSSC.

Structural and magnetic properties of barium-gadolinium hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Litsardakis, G. [Department of Electrical and Computer Engineering, Aristotle University of Thessaloniki, Thessaloniki 54124 (Greece)]. E-mail: Lits@eng.auth.gr; Manolakis, I. [Department of Electrical and Computer Engineering, Aristotle University of Thessaloniki, Thessaloniki 54124 (Greece); Serletis, C. [Department of Physics, Aristotle University of Thessaloniki, Thessaloniki 54124 (Greece); Efthimiadis, K.G. [Department of Physics, Aristotle University of Thessaloniki, Thessaloniki 54124 (Greece)

2007-03-15

A series of Gd-substituted M-type barium hexaferrites has been prepared by the ceramic route, according to the formula (Ba{sub 1-x}Gd{sub x})O.5.25Fe{sub 2}O{sub 3} (x=0-0.30). XRD analysis revealed that all the samples present primarily an M-type structure. Samples x=0 and x=0.05 are single-phase. Hematite (Fe{sub 2}O{sub 3}) and GdFeO{sub 3} were detected in the remaining samples. Coercivity (H{sub c}) shows remarkably high values, {approx}293kA/m for x=0.20 and 0.30 with a maximum of 322kA/m for x=0.25. Specific saturation magnetization ({sigma}{sub sat}) of the samples presents a small increase up to x=0.10. The microstructure examination indicates that Gd may act as a grain growth inhibitor.

Effect of annealing in reduced oxygen pressure on the structure and magnetic properties of M-type hexaferrite bulk and film

Energy Technology Data Exchange (ETDEWEB)

Moon, Kyoung-Seok; Yang, Dae-Jin; Lee, Sang-Eui [Materials R& D Center, Samsung Advanced Institute of Technology, Samsung Electronics, 16677 Suwon (Korea, Republic of); Kim, Dong Hun [Department of Materials Science and Engineering, Myongji University, 17058 Yongin (Korea, Republic of); Kang, Young-Min, E-mail: ymkang@ut.ac.kr [Department of Materials Science & Engineering, Korea National University of Transportation, 27469 Chungju (Korea, Republic of)

2017-06-15

Highlights: • The Ca-La-Co SrM decomposed into the three different ferrite phases after N{sub 2} annealing at 1200 °C. • The charge-imbalance substitution of La{sup 3+}-Co{sup 2+} into SrM induces the phase instability. • The SrM films showed significantly increased M{sub S} with reduced H{sub C} after vacuum annealing. - Abstract: The Ca-La-Co-doped M-type Sr-hexaferrite (Sr{sub 0.1}Ca{sub 0.45}La{sub 0.45}Fe{sub 11.7}Co{sub 0.3}O{sub 19}) decomposed into three different phases of orthorhombic, spinel, and hexagonal structures after annealing at 1200 °C in nitrogen atmosphere while the non-substituted SrFe{sub 12}O{sub 19} maintained the hexagonal structure after annealing at the same condition. It is suggested that the charge-imbalance substitution of La{sup 3+}/Co{sup 2+} = 1.5 induces phase instability of the M-type structure and it causes the phase transformation during the N{sub 2} annealing. In film experiment, polycrystalline Sr-hexaferrite films (SrFe{sub 12}O{sub 19}) have been prepared by pulsed laser deposition and post-annealing processes. When the film was annealed in vacuum at 500 °C, the magnetization value at the magnetic field H = 15 kOe increased by ∼80% and the coercivity decreased significantly without microstructural change.

Synthesis and magnetic properties of (Eu–Ni) substituted Y-type hexaferrite by surfactant assisted co-precipitation method

Energy Technology Data Exchange (ETDEWEB)

Ali, Irshad, E-mail: irshadalibzu@gmail.com [Department of Physics, BahauddinZakariya University, Multan, P.O# 60800 (Pakistan); Islam, M.U. [Department of Physics, BahauddinZakariya University, Multan, P.O# 60800 (Pakistan); Sadiq, Imran [Department of Physics, BahauddinZakariya University, Multan, P.O# 60800 (Pakistan); Centre of Excellence in Solid State Physics, University of The Punjab, Lahore (Pakistan); Karamat, Nazia [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan); Iftikhar, Aisha [Department of Physics, BahauddinZakariya University, Multan, P.O# 60800 (Pakistan); Khan, M. Azhar [Department of Physics, Islamia University of Bahawalpur, 63100 Pakistan (Pakistan); Shah, Afzal [Department of Chemistry, Quaid-i-Azam University, Islamabad 45320 (Pakistan); Athar, Muhammad [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan); Shakir, Imran [Sustainable Energy Technologies (SET) Center, College of Engineering, King Saud University (Saudi Arabia); Ashiq, Muhammad Naeem, E-mail: naeemashiqqau@yahoo.com [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan)

2015-07-01

A series of (Eu–Ni) substituted Y-type hexaferrite with composition Sr{sub 2}Co{sub (2−x)}Ni{sub x}Eu{sub y}Fe{sub (12−y)}O{sub 22} (x=0.0–1, Y=0.0–0.1) were prepared by the surfactant assisted co-precipitation method. The present samples were sintered at 1050 °C for 8 h. The shape of the particles is plate-like which is very advantageous for various applications and the grain size varies from 73 to 269 nm. The values of saturation magnetization (M{sub s}), remanent magnetization (M{sub r}) and magnetic moment (n{sub B}) were found to decrease which are attributed to the weakening of super exchange interactions. The values of in-plane Squareness ratios (M{sub r}/M{sub s}) ranging from 0.41 to 0.65 whereas in case of out of plane measurement it varies from 0.30 to 0.62.The investigated samples can be used in perpendicular recording media (PRM) due to high value of coercivity 2300 Oe which is analogous to the those of M-type and W-type hard magnetic. - Highlights: • The present samples sintered at 1050 °C for 8 h. • The grain size varies from 73 to 269 nm. • The magnetic moment varies from 15.27 to 6.07. • The shape of grains is plate like for microwave devices. • The present samples can be used in PRM due to high value of coercivity i.e. 2300 Oe.

Low-loss Z-type hexaferrite (Ba3Co2Fe24O41) for GHz antenna applications

Science.gov (United States)

Lee, Woncheol; Hong, Yang-Ki; Park, Jihoon; LaRochelle, Gatlin; Lee, Jaejin

2016-09-01

We report a low magnetic loss Ba3Co2Fe24O41 (Co2Z) hexaferrite for use in gigahertz (GHz) antennas. Acid-etching was very effective in removal of unwanted Y-type hexaferrite (Ba2Co2Fe12O22) from calcined Co2Z powder. It is found that the calcined and acid etched (AE) Co2Z hexaferrite shows a low magnetic loss tangent (tan δμ) of 0.012 and 0.037 at 1 and 2 GHz, respectively. These low tan δμ are attributed to removal of Y-type hexaferrite, which possesses a lower anisotropy field (Hk) than W-type hexaferrite (BaCo2Fe16O27). The figure of merit (FOM) of the AE Co2Z hexaferrite is 141.7 and 48.7 at 1 and 2 GHz, respectively. These FOM are much higher than the FOM of previously reported low-loss magnetic materials. Therefore, the AE Co2Z hexaferrite can be a good candidate for GHz antenna application in the ultra-high frequency (UHF) band.

A Comparative Study on Magnetostructural Properties of Barium Hexaferrite Powders Prepared by Polyethylene Glycol

OpenAIRE

Zehra Durmus

2014-01-01

Nanocrystalline particles of barium hexaferrite were synthesized by a sol-gel combustion route using nitrate-citrate gels prepared from metal nitrates and citric acid solutions with Fe/Ba molar ratio 12. The present paper aims to study the effect of addition of polyethylene glycol (PEG) solutions with different molecular weights (MW: 400, 2000, and 10.000 g/mol) on magnetostructural properties of barium hexaferrite. The formation of the barium hexaferrite was inspected using X-ray diffractio...

Electronic structure and photocatalytic activity of wurtzite Cu–Ga–S nanocrystals and their Zn substitution

KAUST Repository

Kandiel, Tarek

2015-03-23

Stoichiometric and gallium-rich wurtzite Cu-Ga-S ternary nanocrystals were synthesized via a facile solution-based hot injection method using 1-dodecanethiol as a sulfur source. The use of 1-dodecanethiol was found to be essential not only as a sulfur source but also as a structure-directing reagent to form a metastable wurtzite structure. In addition, the substitution of zinc in the wurtzite gallium-rich Cu-Ga-S nanocrystals was also investigated. The obtained nanocrystals were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS), photoluminescence (PL), and inductively coupled plasma atomic emission spectroscopy (ICP-OES). Electronic structures of pristine and the Zn-substituted Cu-Ga-S system were investigated using density functional theory (DFT) with HSE06 exchange-correlation functional. The calculated bandgaps accurately reflect the measured ones. The allowed electronic transitions occur upon the photon absorption from the (Cu + S) band towards the (Ga + S) one. The Zn substitution was found not to contribute to the band edge structure and hence altered the bandgaps only slightly, the direct transition nature remaining unchanged with the Zn substitution. The photocatalytic activities of H2 evolution from an aqueous Na2S/Na2SO3 solution under visible-light illumination on the synthesized nanocrystals were investigated. While the stoichiometric CuGaS2 exhibited negligible activity, the gallium-rich Cu-Ga-S ternary nanocrystals displayed reasonable activity. The optimum Zn substitution in the gallium-rich Cu-Ga-S ternary nanocrystals enhanced the H2 evolution rate, achieving an apparent quantum efficiency of >6% at 400 nm. © 2015 The Royal Society of Chemistry.

Bond length variation in Zn substituted NiO studied from extended X-ray absorption fine structure

Science.gov (United States)

Singh, S. D.; Poswal, A. K.; Kamal, C.; Rajput, Parasmani; Chakrabarti, Aparna; Jha, S. N.; Ganguli, Tapas

2017-06-01

Bond length behavior for Zn substituted NiO is determined through extended x-ray absorption fine structure (EXAFS) measurements performed at ambient conditions. We report bond length value of 2.11±0.01 Å for Zn-O of rock salt (RS) symmetry, when Zn is doped in RS NiO. Bond length for Zn substituted NiO RS ternary solid solutions shows relaxed behavior for Zn-O bond, while it shows un-relaxed behavior for Ni-O bond. These observations are further supported by first-principles calculations. It is also inferred that Zn sublattice remains nearly unchanged with increase in lattice parameter. On the other hand, Ni sublattice dilates for Zn compositions up to 20% to accommodate increase in the lattice parameter. However, for Zn compositions more than 20%, it does not further dilate. It has been attributed to the large disorder that is incorporated in the system at and beyond 20% of Zn incorporation in the cubic RS lattice of ternary solid solutions. For these large percentages of Zn incorporation, the Ni and the Zn atoms re-arrange themselves microscopically about the same nominal bond length rather than systematically increase in magnitude to minimize the energy of the system. This results in an increase in the Debye-Waller factor with increase in the Zn concentration rather than a systematic increase in the bond lengths.

Exchange interactions in barium hexaferrite

Czech Academy of Sciences Publication Activity Database

Novák, Pavel; Rusz, J.

2005-01-01

Roč. 71, č. 18 (2005), 184433/1-184433/6 ISSN 1098-0121 R&D Projects: GA AV ČR(CZ) IAA1010214 Institutional research plan: CEZ:AV0Z10100521 Keywords : hexaferrites * exchange interaction * density functional theory Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.185, year: 2005

Composite nanoplatelets combining soft-magnetic iron oxide with hard-magnetic barium hexaferrite

Science.gov (United States)

Primc, D.; Makovec, D.

2015-01-01

By coupling two different magnetic materials inside a single composite nanoparticle, the shape of the magnetic hysteresis can be engineered to meet the requirements of specific applications. Sandwich-like composite nanoparticles composed of a hard-magnetic Ba-hexaferrite (BaFe12O19) platelet core in between two soft-magnetic spinel iron oxide maghemite (γ-Fe2O3) layers were synthesized using a new, simple and inexpensive method based on the co-precipitation of Fe3+/Fe2+ ions in an aqueous suspension of hexaferrite core nanoparticles. The required close control of the supersaturation of the precipitating species was enabled by the controlled release of the Fe3+ ions from the nitrate complex with urea ([Fe((H2N)2C&z.dbd;O)6](NO3)3) and by using Mg(OH)2 as a solid precipitating agent. The platelet Ba-hexaferrite nanoparticles of different sizes were used as the cores. The controlled coating resulted in an exclusively heterogeneous nucleation and the topotactic growth of the spinel layers on both basal surfaces of the larger hexaferrite nanoplatelets. The direct magnetic coupling between the core and the shell resulted in a strong increase of the energy product |BH|max. Ultrafine core nanoparticles reacted with the precipitating species and homogeneous product nanoparticles were formed, which differ in terms of the structure and composition compared to any other compound in the BaO-Fe2O3 system.By coupling two different magnetic materials inside a single composite nanoparticle, the shape of the magnetic hysteresis can be engineered to meet the requirements of specific applications. Sandwich-like composite nanoparticles composed of a hard-magnetic Ba-hexaferrite (BaFe12O19) platelet core in between two soft-magnetic spinel iron oxide maghemite (γ-Fe2O3) layers were synthesized using a new, simple and inexpensive method based on the co-precipitation of Fe3+/Fe2+ ions in an aqueous suspension of hexaferrite core nanoparticles. The required close control of the

Zn substitution NiFe_2O_4 nanoparticles with enhanced conductivity as high-performances electrodes for lithium ion batteries

International Nuclear Information System (INIS)

Mao, Junwei; Hou, Xianhua; Huang, Fengsi; Shen, Kaixiang; Lam, Kwok-ho; Ru, Qiang; Hu, Shejun

2016-01-01

Zn"2"+ ion substituted nickel ferrite nanomaterials with the chemical formula Ni_1_−_xZn_xFe_2O_4 for x = 0, 0.3, 0.5, 0.7 and 1 have been synthesized by a facile green-chemical hydrothermal method as anode materials in lithium ion battery. The morphology and structure of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The physical and electrochemical properties were tested by electrochemical system. Furthermore, the energetic and electronic properties of the samples were investigated by density functional calculations. The results suggest that Zn substitution can affect the conduction performance of the zinc - nickel ferrite. Meanwhile, electrochemical results show that an enhancement in the capacity with increasing Zn concentration is observed especially for x = 0.3 which exhibit high discharge capacity of 1416 mAh g"−"1at the end of 100th cycle. Moreover, the theoretical research method with high yield synthesis strategy described in the present work holds promise for the general fabrication of other metallic elements substitution in complex transition metal oxides for high power LIBs. - Highlights: • Ni_1_−_xZn_xFe_2O_4 anodes have been synthesized by hydrothermal method. • First principles calculation was used to investigate the conduction performance. • Electrochemical performance was enhanced with Zn substitution.

Biological responses of brushite-forming Zn- and ZnSr- substituted beta-tricalcium phosphate bone cements

Directory of Open Access Journals (Sweden)

S Pina

2010-09-01

Full Text Available The core aim of this study was to investigate zinc (Zn- and zinc and strontium (ZnSr-containing brushite-forming beta-tricalcium phosphate (TCP cements for their effects on proliferation and differentiation of osteoblastic-like cells (MC3T3-E1 cell line as well as for their in vivo behaviour in trabecular bone cylindrical defects in a pilot study. In vitro proliferation and maturation responses of MC3T3-E1 osteoblastic-like cells to bone cements were studied at the cellular and molecular levels. The Zn- and Sr-containing brushite cements were found to stimulate pre-osteoblastic proliferation and osteoblastic maturation. Indeed, MC3T3-E1 cells exposed to the powdered cements had increased proliferative rates and higher adhesiveness capacity, in comparison to control cells. Furthermore, they exhibited higher alkaline phosphatase (ALP activity and increased Type-I collagen secretion and fibre deposition into the extracellular matrix. Proliferative and collagen deposition properties were more evident for cells grown in cements doped with Sr. The in vivo osteoconductive propertiesof the ZnCPC and ZnSrCPC cements were also pursued. Histological and histomorphometric analyses were performed at 1 and 2 months after implantation, using carbonated apatite cement (Norian SRS® as control. There was no evidence of cement-induced adverse foreign body reactions, and furthermore ZnCPC and ZnSrCPC cements revealed better in vivo performance in comparison to the control apatite cement. Additionally, the presence of both zinc and strontium resulted in the highest rate of new bone formation. These novel results indicate that the investigated ZnCPC and ZnSrCPC cements are both biocompatible and osteoconductive, being good candidate materials to use as bone substitutes.

Vanadium substitution: A simple and economic way to improve UV sensing in ZnO

Science.gov (United States)

Srivastava, Tulika; Bajpai, Gaurav; Rathore, Gyanendra; Liu, Shun Wei; Biring, Sajal; Sen, Somaditya

2018-04-01

The UV sensing in pure ZnO is due to oxygen adsorption/desorption process from the ZnO surface. Vanadium doping improves the UV sensitivity of ZnO. The enhancement in UV sensitivity in vanadium-substituted ZnO is attributed to trapping and de-trapping of electrons at V4+ and V5+-related defect states. The V4+ state has an extra electron than the V5+ state. A V4+ to V5+ transformation happens with excitation of this electron to the conduction band, while a reverse trapping process liberates a visible light. An analytic study of response phenomenon reveals this trapping and de-trapping process.

A Comparative Study on Magnetostructural Properties of Barium Hexaferrite Powders Prepared by Polyethylene Glycol

Directory of Open Access Journals (Sweden)

Zehra Durmus

2014-01-01

Full Text Available Nanocrystalline particles of barium hexaferrite were synthesized by a sol-gel combustion route using nitrate-citrate gels prepared from metal nitrates and citric acid solutions with Fe/Ba molar ratio 12. The present paper aims to study the effect of addition of polyethylene glycol (PEG solutions with different molecular weights (MW: 400, 2000, and 10.000 g/mol on magnetostructural properties of barium hexaferrite. The formation of the barium hexaferrite was inspected using X-ray diffraction (XRD analysis, Fourier transform infrared (FT-IR analysis, thermogravimetric (TGA analysis, scanning electron microscopy (SEM analysis and vibrating sample magnetometer (VSM analysis for magnetic measurements.

Improvement of high-frequency characteristics of Z-type hexaferrite by dysprosium doping

International Nuclear Information System (INIS)

Mu Chunhong; Liu Yingli; Song Yuanqiang; Wang Liguo; Zhang Huaiwu

2011-01-01

Z-type hexaferrite has great potential applications as anti-EMI material for magnetic devices in the GHz region. In this work, Dy-doped Z-type hexaferrites with nominal stoichiometry of Ba 3 Co 2 Dy x Fe 24-x O 41 (x 0.0, 0.05, 0.5, 1.0) were prepared by an improved solid-state reaction method. The effects of rare earth oxide (Dy 2 O 3 ) addition on the phase composition, microstructure and electromagnetic properties of the ceramics were investigated. Structure and micromorphology characterizations indicate that certain content of Dy doping will cause the emergence of the second phase Dy 3 Fe 5 O 12 at the grain boundaries of the majority phase Z-type hexaferrite, due to which the straightforward result is the grain refinement during the successive sintering process. Permeability spectra measurements show that the initial permeability reaches its maximum of 17 at 300 MHz with x = 0.5, while the cutoff frequency keeps above 800 MHz. The apparent specific anisotropy field H K of Dy-doped Z-type hexaferrites decreases with x increasing. The relationships among phase composition, grain size, permeability spectra, and anisotropy are theoretically investigated, and according to the analysis, Dy doping effects on its magnetic properties can be well explained and understood.

Structural, morphological and electrical properties of Sn-substituted Ni-Zn ferrites synthesized by double sintering technique

Energy Technology Data Exchange (ETDEWEB)

Ali, M.A. [Department of Physics, Chittagong University of Engineering and Technology (CUET), Chittagong 4349 (Bangladesh); Uddin, M.M., E-mail: mohi@cuet.ac.bd [Department of Physics, Chittagong University of Engineering and Technology (CUET), Chittagong 4349 (Bangladesh); Khan, M.N.I. [Materials Science Division, Atomic Energy Center, Dhaka 1000 (Bangladesh); Chowdhury, F.U.-Z. [Department of Physics, Chittagong University of Engineering and Technology (CUET), Chittagong 4349 (Bangladesh); Haque, S.M. [Materials Science Division, Atomic Energy Center, Dhaka 1000 (Bangladesh)

2017-02-15

The Sn-substituted Ni-Zn ferrites, (0.0≤x≤0.30), have been synthesized by the standard double sintering technique from the oxide nanopowders of Ni, Zn, Fe and Sn. The structural and electrical properties have been investigated by the X-ray diffraction (XRD), scanning electron microscopy (SEM), DC resistivity and dielectric measurements. From XRD data, the single cubic spinel phase has been confirmed for x≤0.1, whereas for x>0.1 an extra intermediate phase has been detected along with the cubic spinel phase of Ni-Zn ferrite. The grain size is increased due to Sn substitution in Ni-Zn ferrites. DC resistivity as a function of temperature has been measured by two probe method. The semiconducting nature has been found operative in the samples. The DC resistivity was found to decrease whilst the dielectric constant increased with increasing Sn content in Ni-Zn ferrites. The unusual behavior of the dielectric loss factor of the ferrites was explained by the Rezlescu model. The electrical relaxation of the ferrites has been studied in terms of electric modulus formalism and the time for dielectric relaxation was calculated. The contribution of grain resistance has been studied from the Cole-Cole plot. The suitability to use the as prepared samples in the miniaturized memory devices based capacitive components or energy storage principles are confirmed from the values of dielectric constant. - Highlights: • Sn-substituted Ni-Zn ferrites with cubic spinel structure have been synthesized. • a{sub th} is calculated and well compared with a{sub expt}. • Dielectric unusual behavior has been successfully explained by the Rezlescu model. • Long τ (ns) is determined, can be utilized for memory and spintronics devices.

High temperature superconductivity in Zn and Mn substituted (Tl,Cr)Sr2CaCu2O7

International Nuclear Information System (INIS)

Lo, S.V.; Abd Shukor, R.

1999-01-01

Samples with nominal starting composition (TICr 0 .15)Sr 2 (Ca 1-x M x )Cu 2 O 7 (TI-1212) for x=0 - 0.7 with M= Zn and Mn have been prepared and investigated by powder X-ray diffraction (XRD) and electrical resistance measurements. All sample showed a mixed phase of 1212 and 1201. Dominant 1212-phase was observed for x=0.0-0.5 and x=0.0-0.4, for Zn and Mn series, respectively. The superconducting transition temperature was suppressed when Zn and Mn are substituted at the Ca site. For the Zn series the normal state behavior is metallic throughout the doping range. For the Mn series the normal state behavior is metallic for 0.1≤x≥0.3 and semiconducting like x>0.3. The suppression of T c and formation of the TI-1212 phase are discussed in terms of the ionic radius and valence state of the substituted elements. (author)

Zn substitution NiFe{sub 2}O{sub 4} nanoparticles with enhanced conductivity as high-performances electrodes for lithium ion batteries

Energy Technology Data Exchange (ETDEWEB)

Mao, Junwei [Guang dong Engineering Technology Research Center of Efficient Green Energy and Environmental Protection Materials, Guangzhou 510006 (China); Guang dong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hou, Xianhua, E-mail: houxh@scnu.edu.cn [Guang dong Engineering Technology Research Center of Efficient Green Energy and Environmental Protection Materials, Guangzhou 510006 (China); Guang dong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Huang, Fengsi; Shen, Kaixiang [Guang dong Engineering Technology Research Center of Efficient Green Energy and Environmental Protection Materials, Guangzhou 510006 (China); Guang dong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Lam, Kwok-ho [Department of Electrical Engineering, The Hong Kong Polytechnic University, Hunghom, Kowloon 999077 (Hong Kong); Ru, Qiang [Guang dong Engineering Technology Research Center of Efficient Green Energy and Environmental Protection Materials, Guangzhou 510006 (China); Guang dong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China); Hu, Shejun, E-mail: husj@scnu.edu.cn [Guang dong Engineering Technology Research Center of Efficient Green Energy and Environmental Protection Materials, Guangzhou 510006 (China); Guang dong Provincial Key Laboratory of Quantum Engineering and Quantum Materials, School of Physics and Telecommunication Engineering, South China Normal University, Guangzhou 510006 (China)

2016-08-15

Zn{sup 2+} ion substituted nickel ferrite nanomaterials with the chemical formula Ni{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} for x = 0, 0.3, 0.5, 0.7 and 1 have been synthesized by a facile green-chemical hydrothermal method as anode materials in lithium ion battery. The morphology and structure of the samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The physical and electrochemical properties were tested by electrochemical system. Furthermore, the energetic and electronic properties of the samples were investigated by density functional calculations. The results suggest that Zn substitution can affect the conduction performance of the zinc - nickel ferrite. Meanwhile, electrochemical results show that an enhancement in the capacity with increasing Zn concentration is observed especially for x = 0.3 which exhibit high discharge capacity of 1416 mAh g{sup −1}at the end of 100th cycle. Moreover, the theoretical research method with high yield synthesis strategy described in the present work holds promise for the general fabrication of other metallic elements substitution in complex transition metal oxides for high power LIBs. - Highlights: • Ni{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} anodes have been synthesized by hydrothermal method. • First principles calculation was used to investigate the conduction performance. • Electrochemical performance was enhanced with Zn substitution.

Thermal evolution of exchange interactions in lightly doped barium hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Trukhanov, S.V., E-mail: truhanov@ifttp.bas-net.by [National University of Science and Technology MISiS, Leninsky Prospekt, 4, 119049 Moscow (Russian Federation); SSPA “Scientific and practical materials research centre of NAS of Belarus”, P. Brovki Str., 19, 220072 Minsk, Belorussia (Belarus); Trukhanov, A.V. [National University of Science and Technology MISiS, Leninsky Prospekt, 4, 119049 Moscow (Russian Federation); SSPA “Scientific and practical materials research centre of NAS of Belarus”, P. Brovki Str., 19, 220072 Minsk, Belorussia (Belarus); Kostishyn, V.G.; Panina, L.V. [National University of Science and Technology MISiS, Leninsky Prospekt, 4, 119049 Moscow (Russian Federation); Turchenko, V.A. [Joint Institute for Nuclear Research, Joliot-Curie Str., 141980 Dubna (Russian Federation); Donetsk Institute of Physics and Technology named after A.A. Galkin of the NAS of Ukraine, 72 R.Luxemburg Str., 83114 Donetsk (Ukraine); Kazakevich, I.S. [SSPA “Scientific and practical materials research centre of NAS of Belarus”, P. Brovki Str., 19, 220072 Minsk, Belorussia (Belarus); Trukhanov, An.V. [National University of Science and Technology MISiS, Leninsky Prospekt, 4, 119049 Moscow (Russian Federation); SSPA “Scientific and practical materials research centre of NAS of Belarus”, P. Brovki Str., 19, 220072 Minsk, Belorussia (Belarus); Trukhanova, E.L.; Natarov, V.O. [SSPA “Scientific and practical materials research centre of NAS of Belarus”, P. Brovki Str., 19, 220072 Minsk, Belorussia (Belarus); Balagurov, A.M. [Joint Institute for Nuclear Research, Joliot-Curie Str., 141980 Dubna (Russian Federation)

2017-03-15

The lightly doped BaFe{sub 12−x}D{sub x}O{sub 19} (D=Al{sup 3+}, In{sup 3+}; x=0.1 and 0.3) polycrystalline hexaferrite samples have been investigated by powder neutron diffractometry as well as by vibration sample magnetometry in a wide temperature range from 4 K up to 740 K and in magnetic field up to 14 T to establish the nature of Fe{sup 3+}(Al{sup 3+}, In{sup 3+}) – O{sup 2-} - Fe{sup 3+}(Al{sup 3+}, In{sup 3+}) indirect exchange interactions. The crystal structure features such as the ionic coordinates and lattice parameters have been defined and Rietveld refined. The Invar effect has been observed in low temperature range below 150 K. It was explained by the thermal oscillation anharmonicity of ions. It is established that the ferrimagnet-paramagnet phase transition is a standard second-order one. From the macroscopic magnetization measurement the Curie temperature and ordered magnetic moment per nominal iron ion are obtained. From the microscopic diffraction measurement the magnetic moments at all the nonequivalent ionic positions and total magnetic moment per iron ion have been obtained at different temperatures down to 4 K. The light diamagnetic doping mechanism and magnetic structure model are proposed. The effect of light diamagnetic doping on nature of Fe{sup 3+}(Al{sup 3+}, In{sup 3+}) – O{sup 2-} - Fe{sup 3+}(Al{sup 3+}, In{sup 3+}) indirect exchange interactions with temperature increase is discussed. - Highlights: • Crystal structure for lightly doped barium hexaferrites was investigated. • Atomic coordinates and lattice parameters were Rietveld refined. • Magnetic properties for lightly doped barium hexaferrites was investigated. • Magnetic structure for lightly doped barium hexaferrites was investigated. • Magnetic moments at different position and total moment per iron ion were defined.

Magneto-optical properties BaBi{sub x}La{sub x}Fe{sub 12−2x}O{sub 19} (0.0≤x≤0.5) hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Auwal, I.A. [Department of Chemistry, Fatih University, 34500 B.Çekmece, İstanbul (Turkey); Baykal, A., E-mail: hbaykal@fatih.edu.tr [Department of Chemistry, Fatih University, 34500 B.Çekmece, İstanbul (Turkey); Güner, S. [Department of Physics, Fatih University, 34500 B.Çekmece, İstanbul (Turkey); Sertkol, M. [Department of Physics Engineering, Istanbul Technical University, 34469 Maslak, Istanbul (Turkey); Sözeri, H. [TUBITAK-UME, National Metrology Institute, P.O. Box 54, 41470 Gebze, Kocaeli (Turkey)

2016-07-01

BaBi{sub x}La{sub x}Fe{sub (12−2x)}O{sub 19} (0.0≤x≤0.5) hexaferrites were synthesized by solid state synthesis route and the effects of Bi, La substitutions on structural, magnetic and optical properties were investigated. X-ray powder diffraction, Scanning electron microscopy, Vibrating sample magnetometer, and Percent diffuse reflectance spectroscopy were used to study the physical properties. Room temperature specific magnetization (M–H) curves revealed the ferromagnetic nature of all products. The increasing Bi, La compositions increased the magnetic properties at different magnitudes with respect to undoped BaFe{sub 12}O{sub 19} sample. The maximum values of remnant specific magnetization (M{sub r}=30.3 emu/g), extrapolated specific saturation magnetization (M{sub s}=62.12 emu/g), and magneton number (n{sub B}=16.27) were recorded from BaBi{sub 0.2}La{sub 0.2}Fe{sub 11.4}O{sub 19} hexaferrite. The average crystallite size varies in a range of (37.35–51.36) nm. The coercive field (H{sub c}) of undoped hexaferrites is 1180 Oe and increased to maximum 2320 Oe belonging to BaBi{sub 0.4}La{sub 0.4}Fe{sub 11.2}O{sub 19}. Magnetic anisotropy was confirmed as uniaxial and calculated effective anisotropy constants (K{sub eff}) are between 4.27×10{sup 5} Ergs/g and 5.05×10{sup 5} Ergs/g. The high magnitudes of magnetocrystalline anisotropy (H{sub a}) above than 16,200 Oe revealed that all samples are magnetically hard materials. The Tauc plots were drawn to extrapolate the direct optical energy band gap (E{sub g}) of hexaferrites. The E{sub g} values decreased from 1.76 eV to 1.47 eV with increasing Bi, La compositions. - Highlights: • BaBi{sub x}La{sub x}Fe{sub (12−2x)}O{sub 19} (0.0≤x≤0.5) hexaferrites were synthesized by solid state synthesis route. • The E{sub g} values decreased from 1.76 eV to 1.47 eV with increasing Bi, La compositions. • BaBi{sub xx}La{sub xx}Fe{sub 12-2x}O{sub 19} hexaferrites good candidate for potential applications

Influence of Magnetron Effect on Barium Hexaferrite Thin Layers

International Nuclear Information System (INIS)

Hassane, H.; Chatelon, J.P.; Rousseau, J.J; Siblini, A.; Kriga, A.

2011-01-01

In this paper, we study the effects of a magnet, located in the cathode, on barium hexaferrite thin films deposited by RF magnetron sputtering technique. During the process, these effects can modify thickness, roughness and stress of coatings. The characteristics of the deposited layers depend on the substrate position that is located opposite of magnetron cathode. In the m agnetron area , one can observe that the high stress can produce cracks or detachment of layers and the increasing of both depositing rate and surface roughness. After sputtering elaboration, barium hexaferrite films are in a compressive stress mode. But, after the post-deposition heat treatment these films are in a tensile stress mode. To improve the quality of BaM films, the subsrtate has to be set outside the magnetron area. (author)

Effect of Zn and Ni substitution on structural, morphological and magnetic properties of tin oxide nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Bhuvana, S. [Research and Development Centre, Bharathiar University, Coimbatore 641046, Tamilnadu (India); Department of Physics, Dr. NGP Institute of Technology, Coimbatore 641048, Tamilnadu (India); Ramalingam, H.B.; Vadivel, K. [Department of Physics, Government Arts College, Udumalpet 642126, Tamilnadu (India); Ranjith Kumar, E., E-mail: ranjueaswar@gmail.com [Department of Physics, Dr. NGP Institute of Technology, Coimbatore 641048, Tamilnadu (India); Ayesh, Ahmad I. [Department of Math., Stat. and Physics, Qatar University, Doha (Qatar)

2016-12-01

Structural, morphological, optical and magnetic properties of Zn and Zn–Ni co-doped tin oxide (SnO{sub 2}) nanoparticles synthesized by sol-gel method. The influence of doping concentration on phase and particle size of the nanoparticles was determined by X-ray diffraction. The XRD study reveals that the lattice constant and crystallite size of the samples decrease with the increase of doping concentration. The change in the band gap energy of SnO{sub 2} nanoparticles influenced more by doping with Zn and Ni. The external morphology and particle size were recorded by SEM and TEM. The results indicated that Ni{sup 2+} ions would uniformly substituted into the Zn{sup 2+} sites of SnO{sub 2} lattice. The substitution of Ni creates a vital change in magnetic properties that has been measured by vibrating sample magnetometer (VSM). - Highlights: • Sn{sub 2-(x+y)} Ni{sub x}Zn{sub y}O{sub 2}, (x=y=0.07 to 0.10) nano particles are prepared by simple sol gel method. • X-ray diffraction data confirms the single phase rutile tetragonal structure. • The VSM was used to confirm, the codoping of (Ni, Zn) increases the magnetic moment of the sample prepared. • Inducing ferromagnetism in sample makes it suitable for future spintronics applications.

Hexaferrite multiferroics: from bulk to thick films

Science.gov (United States)

Koutzarova, T.; Ghelev, Ch; Peneva, P.; Georgieva, B.; Kolev, S.; Vertruyen, B.; Closset, R.

2018-03-01

We report studies of the structural and microstructural properties of Sr3Co2Fe24O41 in bulk form and as thick films. The precursor powders for the bulk form were prepared following the sol-gel auto-combustion method. The prepared pellets were synthesized at 1200 °C to produce Sr3Co2Fe24O41. The XRD spectra of the bulks showed the characteristic peaks corresponding to the Z-type hexaferrite structure as a main phase and second phases of CoFe2O4 and Sr3Fe2O7-x. The microstructure analysis of the cross-section of the bulk pellets revealed a hexagonal sheet structure. Large areas were observed of packages of hexagonal sheets where the separate hexagonal particles were ordered along the c axis. Sr3Co2Fe24O41 thick films were deposited from a suspension containing the Sr3Co2Fe24O41 powder. The microstructural analysis of the thick films showed that the particles had the perfect hexagonal shape typical for hexaferrites.

Magnetic studies of cobalt doped barium hexaferrite nanoparticles prepared by modified sol-gel method

International Nuclear Information System (INIS)

Shalini, M. Govindaraj; Sahoo, Subasa C.

2016-01-01

M-type barium hexaferrite (BaFe_1_2O_1_9) and cobalt doped barium hexaferrite (BaFe_1_1CoO_1_9) nanopowders were synthesized by modified sol-gel auto-combustion technique and were annealed at 900°C in air for 4 hours. The annealed powders were studied in the present work and X-ray diffraction studies showed pure phase formation after annealing. The average grain size in the nanopowder sample was decreased after doping. Magnetization value of 60 emu/g was observed at 300 K for the barium hexaferrite and was reduced to 54 emu/g after doping. The coercivity of 5586 Oe was observed at 300 K for the undoped sample and was found to be decreased in the doped sample. As the measurement temperature was decreased from 300 K to 60 K, magnetization value was increased in both the samples compared to those at 300 K. The coercivity of the undoped sample was found to decrease whereas it was increased for the doped sample at 60 K. The observed magnetic properties may be understood on the basis of modified exchange interaction and anisotropy in the doped sample compared to that of pure barium hexaferrite.

Magneto-optical properties of BaCryFe12-yO19 (0.0 ≤ y ≤ 1.0) hexaferrites

Science.gov (United States)

Asiri, S.; Güner, S.; Korkmaz, A. D.; Amir, Md.; Batoo, K. M.; Almessiere, M. A.; Gungunes, H.; Sözeri, H.; Baykal, A.

2018-04-01

In this study, nanocrystalline BaCryFe12-yO19 (0.0 ≤ y ≤ 1.0) hexaferrite powders were prepared by sol-gel auto combustion method and the effect of Cr3+ ion substitution on morphology, structure, optic and magnetic properties of Barium hexaferrite were investigated. X-ray powder diffraction (XRD) analyses confirmed the purity of all samples. The XRD data shows that the average crystallite size lies between 60.95 nm and 50.10 nm and same was confirmed by Transmission electron microscopy. Transmission electron and scanning electron microscopy analyses presented the hexagonal morphology of all products. The characteristic hysteresis (σ-H) curves proved the ferromagnetic feature of as grown nanoparticle samples. Specific saturation magnetization (σs) drops from 46.59 to 34.89 emu/g with increasing Cr content while the coercive field values lie between 770 and 1652 Oe. The large magnitude of the magnetocrystalline (intrinsic) anisotropy field, (Ha) between 11.0 and 12.6 kOe proves that all products are magnetically hard. The energy band gap values decrease from 2.0 eV to 1.84 eV with increasing Cr content. From 57Fe Mössbauer spectroscopy, the variation in line width, isomer shift, quadrupole splitting and hyperfine magnetic field values were determined and discussed.

High quality Y-type hexaferrite thick films for microwave applications by an economical and environmentally benign crystal growth technique

Energy Technology Data Exchange (ETDEWEB)

Hu, Bolin; Chen, Yajie, E-mail: y.chen@neu.edu; Gillette, Scott; Su, Zhijuan; Harris, Vincent G. [Center for Microwave Magnetic Materials and Integrated Circuits and Department of Electrical and Computer Engineering, Northeastern University, Boston, Massachusetts 02115 (United States); Wolf, Jason; McHenry, Michael E. [Materials Science and Engineering, Carnegie Mellon University, Pittsburgh, Pennsylvania 15213 (United States)

2014-02-17

Thick barium hexaferrite Ba{sub 2}Zn{sub 2}Fe{sub 12}O{sub 22} (i.e., Zn{sub 2}Y) films having thicknesses of ∼100 μm were epitaxially grown on MgO (111) substrates using an environmentally benign ferrite-salt mixture by vaporizing the salt. X-ray diffraction pole figure analyses showed (00l) crystallographic alignment with little in plane dispersion confirming epitaxial growth. Saturation magnetization, 4πM{sub s}, was measured for as-grown films to be 2.51 ± 0.1 kG with an out of plane magnetic anisotropy field H{sub A} of 8.9 ± 0.1 kOe. Ferromagnetic resonance linewidth, as the peak-to-peak power absorption derivative at 9.6 GHz, was measured to be 62 Oe. These properties demonstrate a rapid, convenient, cost-effective, and nontoxic method of growing high quality thick crystalline ferrite films which could be used widely for microwave device applications.

Structural and Magnetic Behavioral Improvisation of Nanocalcium Hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Sable, Sharad N., E-mail: sharadtz@hotmail.co [Department of Applied Physics, Priyadarshini College of Engineering, Nagpur (India); Rewatkar, Kishor G. [Department of Physics, Dr. Ambedkar College, Dikshabhumi, Nagpur (India); Nanoti, Vivek M. [Priyadarshini College of Engineering, Nagpur (India)

2010-04-15

In modern technoscientific era, the industrial application of nanomaterials has grabbed a paramount importance owing to their improved characteristics. Hexagonal ferrites especially M-type ferrites have been proved to be the promising candidates for nanomaterials by virtue of their ease of applicability in high density recording media, microwave absorption devices, magneto-optic recording media, etc. Keeping a bird's view over, the samples of varied combinations of M-type substituted hexaferrites are synthesized using sol-gel combustion route by blending nitrates and chlorides as oxidants accompanied with fuels like urea, glycine, citric acid, etc. as reducing agents. The substitution of Co{sup 2+} and Sn{sup 4+} ions lie essentially in the octahedral and tetrahedral sites. As the Fe{sup 3+} ions are being replaced by Co{sup 2+} and Sn{sup 4+} ions, the probability of having oxygen vacancies in the structure was found to be greatly reduced. The magnetic particles produced by conventional solid state reactions are often larger than those produced by sol-gel combustion route. Larger particles of magnetic oxides generally exhibit multidomain magnetic structure whereas nanosized particles generally exhibit single domain magnetic structure. The simultaneous or coupled divalent and tetravalent substitution of Co{sup 2+} and Sn{sup 4+} for Fe{sup 3+} ions greatly helps to improvise the magnetic parameters such as Curie temperature, coercivity, remanent magnetization, saturation magnetization, etc. The structural comparison is being analyzed through the XRD, TEM. The samples so synthesized are found to be reseasonably homogeneous and the average particle size of the sample synthesized is found to be in the nanorange. The structural and magnetic properties are observed be improved upon those of the samples reported earlier. This confirms the more viability of such samples in the various applications of digital data devices. Further attempts could possibly lead to

Magnetic and Dielectric Investigations of Mn-Doped Ba Hexaferrite Nanoparticles by Hydrothermal Approach

Science.gov (United States)

Adeela, N.; Khan, U.; Iqbal, M.; Riaz, S.; Ali, H.; Maaz, K.; Naseem, S.

2016-11-01

A hydrothermal method followed by heat treatment was used to synthesize Mn-substituted Ba2Co2- x Mn x Fe12O22 nanoparticles with a nominal chemical composition of 0 ≤ x < 1 and step gap of 0.3. In this study, the effect of Mn substitution on Co2Y-type barium hexaferrite is investigated after employing x-ray diffraction for crystal structure, field emission scanning electron microscopy for morphology, energy dispersive analysis of x-ray spectroscopy for elemental composition, Fourier transform infrared spectroscopy to confirm bond modes, and vibrating sample magnetometry for magnetic measurements. It was found that the sample at x = 0.9 is of particular interest due to its large coercivity and anisotropy. Later on, for x = 0.9, temperature-dependent magnetic analyses including hysteresis loops, zero-field-cooled, and field-cooled at a particular field of 100 Oe were performed. The decreasing trend in saturation magnetization with increase in temperature was estimated. On the other hand, first an increase and then decrease in coercivity values were observed. These loops also revealed dependence of coercivity on magneto-crystalline anisotropy and average crystallite size of nanoparticles. Dielectric measurements at x = 0.9 make it suitable for high frequency applications.

Structure and multiferroic properties of barium hexaferrite ceramics

International Nuclear Information System (INIS)

Tan, Guolong; Chen, Xiuna

2013-01-01

Simultaneous occurrence of large ferroelectricity and strong ferromagnetism have been observed in barium hexaferrite ceramics. Barium hexaferrite (BaFe 12 O 19 ) powders with hexagonal crystal structure were successfully synthesized in a polymer precursor method using barium acetate and ferric acetylacetonate as the precursors. The powders were pressed into pellets which were sintered into ceramics at 1200 °C and 1300 °C for 1 h. The structure and morphology of the ceramics were examined using X-ray diffraction and field emission scanning electron microscopy. Large spontaneous polarization was observed in the BaFe 12 O 19 ceramics at room temperature, revealing a clear ferroelectric hysteresis loop. The maximum remanent polarization of the BaFe 12 O 19 ceramic was estimated approximately 11.8 μC cm −2 . The FeO 6 octahedron in its perovskite-like hexagonal unit cell and the shift of Fe 3+ off the center of octahedron are suggested to be the origin of the polarization in BaFe 12 O 19 . The BaFe 12 O 19 ceramics also showed strong ferromagnetism at room temperature. - Graphical abstract: Ferroelectric hysteresis loops of BaFe 12 O 19 ceramics measured at a frequency of 120 Hz, which shows that the ceramics sintered at 1200 °C is ferroelectric with P r ∼11.8 μC/cm 2 . Highlights: ► Large ferroelectricity and strong ferromagnetism were observed in barium hexaferrite ceramics. ► The maximum remanent polarization of the BaFe 12 O 19 ceramic was estimated to be 11.8 μC cm −2 . ► The FeO 6 octahedron and off-center shift of Fe 3+ are suggested to be the origin of the polarization.

Identification of substitutional Li in n-type ZnO and its role as an acceptor

Science.gov (United States)

Johansen, K. M.; Zubiaga, A.; Makkonen, I.; Tuomisto, F.; Neuvonen, P. T.; Knutsen, K. E.; Monakhov, E. V.; Kuznetsov, A. Yu.; Svensson, B. G.

2011-06-01

Monocrystalline n-type zinc oxide (ZnO) samples prepared by different techniques and containing various amounts of lithium (Li) have been studied by positron annihilation spectroscopy (PAS) and secondary ion mass spectrometry. A distinct PAS signature of negatively charged Li atoms occupying a Zn-site (LiZn-), so-called substitutional Li, is identified and thus enables a quantitative determination of the content of LiZn. In hydrothermally grown samples with a total Li concentration of ~2×1017cm-3,LiZn is found to prevail strongly, with only minor influence, by other possible configurations of Li. Also in melt grown samples doped with Li to a total concentration as high as 1.5×1019cm-3, a considerable fraction of the Li atoms (at least 20%) is shown to reside on the Zn-site, but despite the corresponding absolute acceptor concentration of ⩾(2-3)×1018cm-3, the samples did not exhibit any detectable p-type conductivity. The presence of LiZn is demonstrated to account for the systematic difference in positron lifetime of 10-15 ps between Li-rich and Li-lean ZnO materials as found in the literature, but further work is needed to fully elucidate the role of residual hydrogen impurities and intrinsic open volume defects.

4D-π-1A type β-substituted ZnII-porphyrins: ideal green sensitizers for building-integrated photovoltaics.

Science.gov (United States)

Covezzi, A; Orbelli Biroli, A; Tessore, F; Forni, A; Marinotto, D; Biagini, P; Di Carlo, G; Pizzotti, M

2016-10-18

Two novel green β-substituted Zn II -porphyrins, G1 and G2, based on a 4D-π-1A type substitution pattern have been synthesized. Their enhanced push-pull character, by reduction of H-L energy gaps, promotes broadening and red-shifting of absorption bands. The effective synthetic pathway and the remarkable spectroscopic properties make G2 ideal for BIPV application.

Investigation on structural properties of M-type strontium hexaferrite synthesized in presence of neem and aloe-vera plant leaves extract

Science.gov (United States)

Solanki, Neha; Jotania, Rajshree B.

2017-05-01

M-type strontium hexaferrite powder samples were synthesized using a green synthesis route with and without presence of Aloe vera and Neem leaves extract. The dry brownish precursors of strontium hexaferrite were recovered from a mixed solution of metal salts and leaves extract, heated at 100 °C. The obtained precursors were pre-heated at 500 °C for 4 hrs. followed by final heating at 950 °C for 4 hrs. in a muffle furnace to obtain SrFe12O19 hexaferrite powder. The obtained SrFe12O19 hexaferrite powder samples characterized at room temperature in order to check phase purity and structural properties. XRD analysis confirms that samples prepared without and with Aloe vera leaves extract (heated at 950 °C for 4 hrs.) show formation of α-Fe2O3 and M-phase; while the sample prepared in presence of Neem leaves extract (heated at 950 °C for 4 hrs.) show formation of mono phase of strontium hexaferrite. Lattice parameter (a) and cell volume (V) are found to increase in the samples prepared in presence of Aloe vera and Neem leaves extract.

Simultaneous effect of crystal lattice and non magnetic substitution on magnetic properties of barium hexaferrite

Science.gov (United States)

Kumar, Sunil; Supriya, Sweety; Pradhan, Lagen Kumar; Pandey, Rabichandra; Kar, Manoranjan

2018-05-01

The aluminium doped barium hexaferrite BaFe12-xAlxO19 with x =0.0, 1.0, 2.0, 4.0 and 6.0 have been synthesized by the sol-gel method to modify the magnetic properties for technological applications. The crystal structure and phase purity of all the samples have been explored by employing the X-ray diffraction (XRD) technique. It confirms that the sample is nanocrystalline, hexagonal symmetry and all the intense peaks could be indexed to the P63/mmc space group. The obtained lattice parameters from the XRD analysis decrease with the increase in Al3+ content in the samples. The microstructural morphology and particle sizes of all samples were studied by using the Field Emission Scanning Electron Microscopy (FESEM-Hitachi-S4800) technique. The magnetic hysteresis (M-H) loops measurement has been carried out at room temperature by employing the vibrating sample magnetometer (VSM) over a field range of +20 kOe to -20 kOe. The magnetic hysteresis (M-H) loops revealed the ferromagnetic (hard magnetic materials) nature of the samples and, analyzed by using the Law of Approach to Saturation.

Synthesis and micro-structural characterization of graphene/strontium hexaferrite (SrFe{sub 12}O{sub 19}) nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Durmus, Zehra, E-mail: zdurmus@bezmialem.edu.tr [Department of Pharmaceutical Biotechnology, Bezmialem Vakif University, 34093, Fatih, Istanbul (Turkey); Kavas, Huseyin [Department of Engineering Physics, Istanbul Medeniyet University, 34700, Kadıköy, Istanbul (Turkey); Durmus, Ali [Department of Chemical Engineering, Istanbul University, 34320, Avcılar, Istanbul (Turkey); Aktaş, Bekir [Department of Physics, Gebze Technical University, 41400, Gebze, Kocaeli (Turkey)

2015-08-01

In this study, novel type carbon/ferrite nanocomposites were successfully prepared by decoration of graphene sheets with the magnetic strontium hexaferrite nanoparticles synthesized via the citrate sol–gel combustion method as microwave absorbing material. The microstructural features and physical properties of nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM) methods. Magnetic properties of the nanocomposites were determined by a vibrating sample magnetometer (VSM). It was found that the surface of the graphene nanosheets were successfully decorated with the strontium hexaferrite nanoparticles and the resulting layered nanocomposite structures exhibited sufficiently high magnetic saturation values compared to the agglomerated structure of strontium hexaferrite nanoparticles although the nanocomposites include less active magnetic component than the bulk hexaferrite. - Highlights: • Novel type, two-dimensional carbon-ferrite nanocomposites were prepared. • 2D graphene sheets were successfully decorated with the SrFe{sub 12}O{sub 19} nanoparticles. • Morphologies of nanocomposites were characterized with SEM, TEM and AFM methods. • Graphene/SrFe{sub 12}O{sub 19} nanocomposites exhibited sufficiently high M{sub s} values.

Intrinsic magnetism of a series of Co substituted ZnO single crystals

International Nuclear Information System (INIS)

Lv Peiwen; Huang Feng; Chu Wangsheng; Lin Zhang; Chen Dagui; Li Wei; Chen Dongliang; Wu Ziyu

2008-01-01

Magnetic properties of a series of well-substituted Zn 1-x Co x O (x = 0.018,0.036 and 0.05) single crystals were studied. A typical paramagnetic anisotropy property, which strengthens when x decreases, was found. A magnetization step was observed at 2 K when the magnetic field is parallel to the c axis, indicating that paramagnetic anisotropy is the origin of the strong crystal field effect on Co 2+ ions in ZnO lattices. The Co 2+ single-ion anisotropy parameter 2D is obtained as 7.5 K. The effective moment of Co 2+ takes the values 2.7 μ B , 1.82 μ B , 1.49 μ B when x = 0.018, 0.036 and 0.05, revealing that more antiferromagnetic coupling between Co 2+ ions arises in the perfect crystal when x increases

Zn2+ in-situ substitution behavior during the formation of BaTiO3 coatings from plasma-sprayed powders collected in liquid nitrogen

Science.gov (United States)

Liu, Zhe; Xing, Zhiguo; Wang, Haidou; Xue, Zifan; Chen, Shuying; Cui, Xiufang; Jin, Guo

2018-04-01

The dielectric performance of BaTiO3 ceramic coatings is enhanced significantly by the addition of ZnO. In this study, the maximum relative permittivity value (εr ≈ 923) was measured in BaTiO3 coatings with ZnO added at 6 wt%. The Curie temperature (Tc) was in the range of 111 °C-121 °C for all of the ZnO-modified BaTiO3 coatings. Tc shifted to low temperatures as the ZnO content increased. Detailed analyses were performed to determine the phase composition and optical band gaps of powders collected in liquid nitrogen, which showed that the Zn2+ ions were incorporated into the BaTiO3 lattice where they substituted into the Ti4+ sites, and the composite powders (BaTiO3 + 6 wt% ZnO) tolerated high temperatures in the plasma beam. In addition, some residual Zn accumulated in the grain boundary in the form of ZnO. X-ray diffraction and Raman spectroscopy showed that the substitution led to changes in the compositional and structural properties. The red shift in the optical band gap of BaTiO3 indicated that the ZnTi'' defects caused by the dopants acted as carriers in the doped BaTiO3 coatings.

Synthesis, characterization and modelling of zinc and silicate co-substituted hydroxyapatite.

Science.gov (United States)

Friederichs, Robert J; Chappell, Helen F; Shepherd, David V; Best, Serena M

2015-07-06

Experimental chemistry and atomic modelling studies were performed here to investigate a novel ionic co-substitution in hydroxyapatite (HA). Zinc, silicate co-substituted HA (ZnSiHA) remained phase pure after heating to 1100 °C with Zn and Si amounts of 0.6 wt% and 1.2 wt%, respectively. Unique lattice expansions in ZnSiHA, silicate Fourier transform infrared peaks and changes to the hydroxyl IR stretching region suggested Zn and silicate co-substitution in ZnSiHA. Zn and silicate insertion into HA was modelled using density functional theory (DFT). Different scenarios were considered where Zn substituted for different calcium sites or at a 2b site along the c-axis, which was suspected in singly substituted ZnHA. The most energetically favourable site in ZnSiHA was Zn positioned at a previously unreported interstitial site just off the c-axis near a silicate tetrahedron sitting on a phosphate site. A combination of experimental chemistry and DFT modelling provided insight into these complex co-substituted calcium phosphates that could find biomedical application as a synthetic bone mineral substitute. © 2015 The Author(s) Published by the Royal Society. All rights reserved.

Synthesis, characterization and modelling of zinc and silicate co-substituted hydroxyapatite

Science.gov (United States)

Friederichs, Robert J.; Chappell, Helen F.; Shepherd, David V.; Best, Serena M.

2015-01-01

Experimental chemistry and atomic modelling studies were performed here to investigate a novel ionic co-substitution in hydroxyapatite (HA). Zinc, silicate co-substituted HA (ZnSiHA) remained phase pure after heating to 1100°C with Zn and Si amounts of 0.6 wt% and 1.2 wt%, respectively. Unique lattice expansions in ZnSiHA, silicate Fourier transform infrared peaks and changes to the hydroxyl IR stretching region suggested Zn and silicate co-substitution in ZnSiHA. Zn and silicate insertion into HA was modelled using density functional theory (DFT). Different scenarios were considered where Zn substituted for different calcium sites or at a 2b site along the c-axis, which was suspected in singly substituted ZnHA. The most energetically favourable site in ZnSiHA was Zn positioned at a previously unreported interstitial site just off the c-axis near a silicate tetrahedron sitting on a phosphate site. A combination of experimental chemistry and DFT modelling provided insight into these complex co-substituted calcium phosphates that could find biomedical application as a synthetic bone mineral substitute. PMID:26040597

Zinc and Carbonate Co-Substituted Nano-Hydroxyapatite

Science.gov (United States)

Girija, E. K.; Kumar, G. Suresh; Thamizhavel, A.

2011-07-01

Synthesis of Zn or CO32- substituted nano-hydroxyapatite (HA) and its physico-chemical properties have been well documented. However, the effects of the simultaneous substitution of Zn and CO32- in nano-HA have not been reported. In the present study, Zn and CO32- substitutions in nano HA independently and concurrently have been done by wet precipitation method and characterized by XRD and FT-IR for its phase purity and chemical homogeneity. Further modulations of the bioactivity and thermal stability of HA due to the substitutions have been studied.

Intrinsic magnetism of a series of Co substituted ZnO single crystals

Energy Technology Data Exchange (ETDEWEB)

Lv Peiwen [Laboratory of Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, National Engineering Research Center for Optoelectronic Crystalline Materials, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Huang Feng [Laboratory of Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, National Engineering Research Center for Optoelectronic Crystalline Materials, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Chu Wangsheng [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, 100049 Beijing (China); Lin Zhang [Laboratory of Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, National Engineering Research Center for Optoelectronic Crystalline Materials, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Chen Dagui [Laboratory of Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, National Engineering Research Center for Optoelectronic Crystalline Materials, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Li Wei [Laboratory of Materials Chemistry and Physics, Fujian Institute of Research on the Structure of Matter, National Engineering Research Center for Optoelectronic Crystalline Materials, Chinese Academy of Sciences, Fuzhou, Fujian 350002 (China); Chen Dongliang [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, 100049 Beijing (China); Wu Ziyu [Beijing Synchrotron Radiation Facility, Institute of High Energy Physics, Chinese Academy of Sciences, 100049 Beijing (China)

2008-01-23

Magnetic properties of a series of well-substituted Zn{sub 1-x}Co{sub x}O (x = 0.018,0.036 and 0.05) single crystals were studied. A typical paramagnetic anisotropy property, which strengthens when x decreases, was found. A magnetization step was observed at 2 K when the magnetic field is parallel to the c axis, indicating that paramagnetic anisotropy is the origin of the strong crystal field effect on Co{sup 2+} ions in ZnO lattices. The Co{sup 2+} single-ion anisotropy parameter 2D is obtained as 7.5 K. The effective moment of Co{sup 2+} takes the values 2.7 {mu}{sub B}, 1.82 {mu}{sub B}, 1.49 {mu}{sub B} when x = 0.018, 0.036 and 0.05, revealing that more antiferromagnetic coupling between Co{sup 2+} ions arises in the perfect crystal when x increases.

Spectrum designation and effect of Al substitution on the luminescence of Cr3+ doped ZnGa2O4 nano-sized phosphors

International Nuclear Information System (INIS)

Zhang Weiwei; Zhang Junying; Chen Ziyu; Wang Tianmin; Zheng Shukai

2010-01-01

Low-temperature photoluminescent spectra of ZnGa 2 O 4 :Cr 3+ nano-sized phosphors calcined at different temperatures were reported. The fine structure of the emission spectra has been designated to Cr 3+ ions in different sites including ideal octahedral, Zn-interstitial, Ga ZN 4 -Zn Ga 6 sites and Ga 2 O 3 impurity. The vibronic sidebands for both Stokes' and anti-Stokes' sides are related to the host lattice vibrations, which were confirmed by IR and Raman spectra. Al 3+ is substituted in Ga 3+ sites to form Zn(Ga 1-y Al y ) 2 O 4 :Cr 0.01 3+ (0≤y≤0.5). The blue shift and luminescent intensity variations of the charge transfer band and 3d-3d transitions in the spectra caused by Al substitution were related to larger band gap and stronger crystal field, respectively. The calculated crystal-field parameters indicated that Al incorporation enhanced the crystal field strength and induced more trigonal distortion due to different radii of Al 3+ and Ga 3+ .

Monolithic Magneto-Optical Nanocomposites of Barium Hexaferrite Platelets in PMMA.

Science.gov (United States)

Ferk, Gregor; Krajnc, Peter; Hamler, Anton; Mertelj, Alenka; Cebollada, Federico; Drofenik, Miha; Lisjak, Darja

2015-06-12

The incorporation of magnetic barium hexaferrite nanoparticles in a transparent polymer matrix of poly(methyl methacrylate) (PMMA) is reported for the first time. The barium hexaferrite nanoplatelets doped with Sc(3+), i.e., BaSc0.5Fe11.5O12 (BaHF), having diameters in the range 20 to 130 nm and thicknesses of approximately 5 nm, are synthesized hydrothermally and stabilized in 1-butanol with dodecylbenzenesulfonic acid. This method enables the preparation of monolithic nanocomposites by admixing the BaHF suspension into a liquid monomer, followed by in-situ, bulk free-radical polymerization. The PMMA retains its transparency for loadings of BaHF nanoparticles up to 0.27 wt.%, meaning that magnetically and optically anisotropic, monolithic nanocomposites can be synthesized when the polymerization is carried out in a magnetic field. The excellent dispersion of the magnetic nanoparticles, coupled with a reasonable control over the magnetic properties achieved in this investigation, is encouraging for the magneto-optical applications of these materials.

Structural, magnetic and microwave absorption behavior of Co-Zr substituted strontium hexaferrites prepared using tartaric acid fuel for electromagnetic interference suppression

Energy Technology Data Exchange (ETDEWEB)

Kaur, Prabhjyot, E-mail: prabhjyot.2525@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar 143005 (India); Chawla, S.K., E-mail: sschawla118@gmail.com [Department of Chemistry, Centre for Advanced Studies-I, Guru Nanak Dev University, Amritsar 143005 (India); Narang, Sukhleen Bindra, E-mail: sukhleen2@yahoo.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar 143005 (India); Pubby, Kunal, E-mail: kunalpubby02@gmail.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar 143005 (India)

2017-01-15

Strontium hexaferrites, doped with varying Co-Zr content (x) have been synthesized by sol-gel auto-combustion route using tartaric acid as fuel at 800 °C. X-ray diffraction and Fourier transform Infra-red have been carried out to confirm the phase formation, particle size (average 21.9–36.8 nm) and the bond formation respectively. Magnetic properties are scrutinized using vibrating sample magnetometer. Techniques like scanning electron microscopy, transmission electron microscopy and energy dispersive scattering have been employed to explore the surface morphology, particle size and composition of the nano-powders. Electromagnetic characterization of the prepared ferrites has been done using Vector Network Anlyzer in 12.4–18 GHz frequency range. The effect of calcination temperature (500–1000 °C) on the structure, morphology and magnetic properties has also been studied for x=0.2 and 800 °C has been found to be the most suitable temperature with the best magnetic properties. Increase in doping has resulted in resonance peaks in dielectric and magnetic loss spectra, leading to microwave absorption peaks. Ferrites with x=0.2, 0.8 and 1.0 have appropriate reflection loss less than −10 dB and bandwidth in Ku-band, hence can be used as effective absorbers in suppression of electromagnetic interference (EMI). The governance of impedance matching in deciding the absorption properties has been proved by using input impedance calculations. - Highlights: • Co-Zr doped strontium hexaferrite nanopowders have been prepared by sol-gel route. • 800 °C was most suitable temperaturewith best structural and magnetic properties. • Samples have M-type hexagonal structure with an average particle size of 36.47 nm. • Samples x=0.2, 0.8 and 1.0 are suitable for suppression of EM waves in Ku-band. • The origin of absorption peaks: impedance matching and losses has been explained.

Rare earth doped M-type hexaferrites; ferromagnetic resonance and magnetization dynamics

Directory of Open Access Journals (Sweden)

Vipul Sharma

2018-05-01

Full Text Available M-type hexagonal barium ferrites come in the category of magnetic material that plays a key role in electromagnetic wave propagation in various microwave devices. Due to their large magnetic anisotropy and large magnetization, their operating frequency exceeds above 50 GHz. Doping is a way to vary its magnetic properties to such an extent that its ferromagnetic resonance (FMR response can be tuned over a broad frequency band. We have done a complete FMR study of rare earth elements neodymium (Nd and samarium (Sm, with cobalt (Co as base, doped hexaferrite nanoparticles (NPs. X-ray diffractometry, vibrating sample magnetometer (VSM, and ferromagnetic resonance (FMR techniques were used to characterize the microstructure and magnetic properties of doped hexaferrite nanoparticles. Using proper theoretical electromagnetic models, various parameters are extracted from FMR data which play important role in designing and fabricating high-frequency microwave devices.

Preparation and magnetic properties of the Sr-hexaferrite with foam structure

Energy Technology Data Exchange (ETDEWEB)

Guerrero, A.L., E-mail: azdlobo@gmail.com [Instituto de Física-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico); Facultad de Ingeniería-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico); Espericueta, D.L. [Facultad de Ingeniería-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico); Facultad de Ciencias-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico); Palomares-Sánchez, S.A. [Facultad de Ciencias-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico); Elizalde-Galindo, J.T. [Instituto de Ingeniería y Tecnología-UACJ, Av. Plutarco Elías Calles 1210, Fovissste Chamizal, Ciudad Juárez, Chihuahua (Mexico); Watts, B.E [IMEM-CNR, Parco Area delle Scienze 37/A, 43124 Parma (Italy); Mirabal-García, M. [Instituto de Física-UASLP, Álvaro Obregón 64, Centro. San Luis Potosí, S.L.P. (Mexico)

2016-12-01

This work reports an optimal way to fabricate strontium hexaferrite with porous-reticulated structure using a variation of the replication technique and taking two different precursors, one obtained from the coprecipitation and the other from the ceramic method. Changes made to the original replication technique include the addition of Arabic gum as binder, and the addition of ethylene glycol to form the ceramic sludge. In addition, some parameters such as the relation between solid material and liquid phase, the quantity of binder and the heat treatment were varied to obtain high quality magnetic foams. Two polymeric sponges were used as patterns, one with average pore size of 300 μm diameter and the other with 1100 μm. The characterization of the samples included the analysis of the structure and phase purity, the magnetic properties, the remanence properties, magnetic interactions and the microstructural characteristics. Results indicate that both, the powder precursors and the polymeric pattern play an important role in the configuration of the foam structure and this configuration has an important influence on the dipolar interactions which tend to demagnetize the samples. In addition, it was analyzed the behavior between the minimum value of the δM curves and the hysteresis properties. - Highlights: • New way to obtain Sr-hexaferrite with foam structure and high magnetic performance. • Relation between pore structure and the magnetic properties in ceramic foams. • Analysis of magnetostatic interactions with the magnetism of Sr-hexaferrite foams. • Relation between microstructural characteristics and the magnetization of the foams.

Preparation and magnetic properties of the Sr-hexaferrite with foam structure

International Nuclear Information System (INIS)

Guerrero, A.L.; Espericueta, D.L.; Palomares-Sánchez, S.A.; Elizalde-Galindo, J.T.; Watts, B.E; Mirabal-García, M.

2016-01-01

This work reports an optimal way to fabricate strontium hexaferrite with porous-reticulated structure using a variation of the replication technique and taking two different precursors, one obtained from the coprecipitation and the other from the ceramic method. Changes made to the original replication technique include the addition of Arabic gum as binder, and the addition of ethylene glycol to form the ceramic sludge. In addition, some parameters such as the relation between solid material and liquid phase, the quantity of binder and the heat treatment were varied to obtain high quality magnetic foams. Two polymeric sponges were used as patterns, one with average pore size of 300 μm diameter and the other with 1100 μm. The characterization of the samples included the analysis of the structure and phase purity, the magnetic properties, the remanence properties, magnetic interactions and the microstructural characteristics. Results indicate that both, the powder precursors and the polymeric pattern play an important role in the configuration of the foam structure and this configuration has an important influence on the dipolar interactions which tend to demagnetize the samples. In addition, it was analyzed the behavior between the minimum value of the δM curves and the hysteresis properties. - Highlights: • New way to obtain Sr-hexaferrite with foam structure and high magnetic performance. • Relation between pore structure and the magnetic properties in ceramic foams. • Analysis of magnetostatic interactions with the magnetism of Sr-hexaferrite foams. • Relation between microstructural characteristics and the magnetization of the foams.

Nanofiber production of poly (vinylidene fluoride) / hexaferrite, obtained by Blow Spinning Technique

International Nuclear Information System (INIS)

Dias, G.C.; Zadorosny, L.; Malmonge, J.A.; Malmonge, L.F.

2014-01-01

In this study, fibrous films of poly (vinylidene fluoride) - PVDF with barium hexaferrite particles were obtained by Solution Blow Spinning technique. In such technique, the polymer solution is injected through an inner nozzle which experiences the action of an accelerated flux of gas that drags and stretches the jet solution forming the nanofibers. The films were obtained from solutions of PVDF/DMF (30% w/v), which was incorporated into barium hexaferrite particles in proportions of 1, 3 and 5% (w / w). The results of the micrographs revealed the formation of a fibrous film with good dispersion of the particles. Xray analyzes showed the predominance of the β crystalline phase of PVDF. The increase of the amount of particles induces the appearance of a characteristic peak of PVDF. EDX measurements confirmed the presence of particles in the films. (author)

Structural, magneto-optical properties and cation distribution of SrBi{sub x}La{sub x}Y{sub x}Fe{sub 12−3x}O{sub 19} (0.0 ≤ x ≤ 0.33) hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Auwal, I.A. [Department of Chemistry, Fatih University, 34500 B. Çekmece, İstanbul (Turkey); Güngüneş, H. [Department of Physics, Hitit University, 19030 Çevre Yolu Bulvarı, Çorum (Turkey); Güner, S. [Department of Physics, Fatih University, 34500 B. Çekmece, İstanbul (Turkey); Shirsath, Sagar E. [Spin Device Technology Center, Faculty of Engineering, Shinshu University, 380-8553 Nagano (Japan); Sertkol, M. [Department of Physics Engineering, Istanbul Technical University, 34469 Maslak (Turkey); Baykal, A., E-mail: hbaykal@fatih.edu.tr [Department of Chemistry, Fatih University, 34500 B. Çekmece, İstanbul (Turkey)

2016-08-15

Highlights: • SrBi{sub x}La{sub x}Y{sub x}Fe{sub 12−3x}O{sub 19} (0.0 ≤ x ≤ 0.33) hexaferrites have been prepared by sol-gel autocombustion. • XRD patterns show that SrBi{sub x}La{sub x}Y{sub x}Fe{sub 12−3x}O{sub 19} (0.0 ≤ x ≤ 0.33) hexaferrites exhibit hexagonal structure. • The intrinsic coercivity (H{sub ci}) above 15000 Oe reveals that all samples are magnetically hard materials. - Abstract: SrBi{sub x}La{sub x}Y{sub x}Fe{sub 12−3x}O{sub 19} (0.0 ≤ x ≤ 0.33) hexaferrites were produced via sol-gel auto combustion. XRD patterns show that all the samples are single-phase M-type strontium hexaferrite (SrM). The magnetic hysteresis (σ-H) loops revealed the ferromagnetic nature of nanoparticles (NPs). The coercive field decreases from 4740 Oe to 2720 Oe with increasing ion content. In particular, SrBi{sub x}La{sub x}Y{sub x}Fe{sub 12−3x}O{sub 19} NPs with x = 0.0, 0.1, 0.2 have suitable magnetic characteristics (σ{sub s} = 62.03–64.72 emu/g and H{sub c} = 3105–4740 Oe) for magnetic recording. The intrinsic coercivity (H{sub ci}) above 15000 Oe reveals that all samples are magnetically hard materials. Tauc plots were used to specify the direct optical energy band gap (E{sub g}) of NPs. The E{sub g} values are between 1.76 eV and 1.85 eV. {sup 57}Fe Mössbauer spectroscopy data, the variation in line width, isomer shift, quadrupole splitting, relative area and hyperfine magnetic field values on Bi{sup 3+} La{sup 3+} and Y{sup 3+} substitutions have been determined.

Enhancement of structural and magnetic properties of M-type hexaferrite permanent magnet based on synthesis temperature

Science.gov (United States)

Anjum, Safia; Sehar, Fatima; Mustafa, Zeeshan; Awan, M. S.

2018-01-01

The main purpose of this research work is to develop the single domain magnetic particles of M-type barium hexaferrite (BaFe12O19) using oxide precursors employing conventional powder metallurgy technique. The phase formation and magnetic performance of the powders and magnets will be optimized by adjusting calcination and sintering temperatures. The synthesis of M-type barium hexaferrite was carried out in two sections. A series of four samples have been prepared by initial wet mixed powders calcined at different temperatures, i.e., 750, 850, 950 and 1050 °C. On the basis of structural analysis, the sample calcined at 950 °C has been selected and further divided into four parts to sintered them at 1100, 1150, 1200 and 1250 °C. The structural measurements depict the confirmation of M-type barium hexaferrite structure. SEM micrographs show the hexagonal-shaped grains. The abrupt decrease in coercivity for the sample sintered at 1250 °C has been seen which may be due to high sintering temperature, at which the particles have multi-domain properties.

High temperature dielectric studies of indium-substituted NiCuZn nanoferrites

Science.gov (United States)

Hashim, Mohd.; Raghasudha, M.; Shah, Jyoti; Shirsath, Sagar E.; Ravinder, D.; Kumar, Shalendra; Meena, Sher Singh; Bhatt, Pramod; Alimuddin; Kumar, Ravi; Kotnala, R. K.

2018-01-01

In this study, indium (In3+)-substituted NiCuZn nanostructured ceramic ferrites with a chemical composition of Ni0.5Cu0.25Zn0.25Fe2-xInxO4 (0.0 ≤ x ≤ 0.5) were prepared by chemical synthesis involving sol-gel chemistry. Single phased cubic spinel structure materials were prepared successfully according to X-ray diffraction and transmission electron microscopy analyses. The dielectric properties of the prepared ferrites were measured using an LCR HiTester at temperatures ranging from room temperature to 300 °C at different frequencies from 102 Hz to 5 × 106 Hz. The variations in the dielectric parameters ε‧ and (tanδ) with temperature demonstrated the frequency- and temperature-dependent characteristics due to electron hopping between the ions. The materials had low dielectric loss values in the high frequency range at all temperatures, which makes them suitable for high frequency microwave applications. A qualitative explanation is provided for the dependences of the dielectric constant and dielectric loss tangent on the frequency, temperature, and composition. Mӧssbauer spectroscopy was employed at room temperature to characterize the magnetic behavior.

Novel water soluble morpholine substituted Zn(II) phthalocyanine: Synthesis, characterization, DNA/BSA binding, DNA photocleavage and topoisomerase I inhibition.

Science.gov (United States)

Barut, Burak; Demirbaş, Ümit; Özel, Arzu; Kantekin, Halit

2017-12-01

In this study, novel peripherally tetra 3-morpholinophenol substituted zinc(II) phthalocyanine (4) and its water soluble form quaternized zinc(II) phthalocyanine (ZnQ) were synthesized for the first time. These novel compounds were characterized by a combination of different spectroscopic techniques such as FT-IR, 1 H NMR, 13 C NMR, UV-vis and mass. The DNA binding of ZnQ was investigated using UV-vis absorption titration, competitive ethidium bromide, thermal denaturation and viscosity experiments that the ZnQ bound to CT-DNA via intercalation mode. ZnQ indicated photocleavage activity on supercoiled pBR322 plasmid DNA via formation of singlet oxygen under irradiation at 700nm. Besides, the topoisomerase I inhibitory effect experiments showed that ZnQ inhibited topoisomerase I enzyme in a concentration-dependent manner. The bovine serum albumin (BSA) binding experiments indicated that ZnQ bound to proteins through a static quenching mechanism. All of these results claim that ZnQ has potential agent for photodynamic therapy owing to its nucleic acid interactions and photobiological or photochemical properties. Copyright © 2017 Elsevier B.V. All rights reserved.

Tailoring magnetic properties of self-biased hexaferrites using an alternative copolymer of isobutylene and maleic anhydride

Science.gov (United States)

Wu, Chuanjian; Yu, Zhong; Sokolov, Alexander S.; Yu, Chengju; Sun, Ke; Jiang, Xiaona; Lan, Zhongwen; Harris, Vincent G.

2018-05-01

Discussed is a novel self-biased hexaferrite gelling system based on a nontoxic and water-soluble copolymer of isobutylene and maleic anhydride. This copolymer simultaneously acts as a dispersant and gelling agent, and recently received much attention from the ceramics community. Herein its effects on the rheological conditions throughout magnetic-field pressing, and consequently, orientation, density and magnetic properties of textured hexaferrites were investigated. Ka-band FMR linewidths were measured, and the crystalline anisotropy and porosity induced linewidth broadening were estimated according to Schlömann's theory. The copolymer allowed to reduce the friction between micron-sized magnetic particulates, resulting in higher density and degree of crystalline orientation, and lower FMR linewidth.

Magnetic, hyperthermic and structural properties of zn substituted CaFe2O4 powders

Science.gov (United States)

Kheradmand, Abbas; Vahidi, Omid; Masoudpanah, S. M.

2018-03-01

In the present study, we have synthesized single phase Ca1 - x Zn x Fe2O4 powders by hydrothermal method. The cation distribution between the tetrahedral and octahedral sites in the spinel structure and the magnetic properties as a function of the zinc substitution have been investigated by X-ray diffraction (XRD), infrared spectroscopy and vibrating sample magnetometer methods. The obtained XRD pattern indicated that the synthesized particles had single phase cubic spinel structure with no impurity. The magnetic measurements showed that the saturation magnetization increased from 83 to 98 emu/g with the addition of zinc due to the decrease of inversity. The particle size observed by electron microscopy decreased from 1.38 to 0.97 µm with the increase of zinc addition. The Ca0.7Zn0.3Fe2O4 powders exhibited appropriate heating capability for hyperthermia applications with the maximum AC heating temperature of 20 °C and specific loss power of 9.29 W/g.

Spectrum designation and effect of Al substitution on the luminescence of Cr{sup 3+} doped ZnGa{sub 2}O{sub 4} nano-sized phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhang Weiwei [Key Laboratory of Micro-nano Measurement, Manipulation and Physics (Ministry of Education), School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Zhang Junying, E-mail: zjy@buaa.edu.c [Key Laboratory of Micro-nano Measurement, Manipulation and Physics (Ministry of Education), School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Chen Ziyu; Wang Tianmin [Key Laboratory of Micro-nano Measurement, Manipulation and Physics (Ministry of Education), School of Physics and Nuclear Energy Engineering, Beihang University, Beijing 100191 (China); Zheng Shukai [College of Electronic and Information Engineering, Hebei University, Baoding 071200 (China)

2010-10-15

Low-temperature photoluminescent spectra of ZnGa{sub 2}O{sub 4}:Cr{sup 3+} nano-sized phosphors calcined at different temperatures were reported. The fine structure of the emission spectra has been designated to Cr{sup 3+} ions in different sites including ideal octahedral, Zn-interstitial, Ga{sub ZN}{sup 4}-Zn{sub Ga}{sup 6} sites and Ga{sub 2}O{sub 3} impurity. The vibronic sidebands for both Stokes' and anti-Stokes' sides are related to the host lattice vibrations, which were confirmed by IR and Raman spectra. Al{sup 3+} is substituted in Ga{sup 3+} sites to form Zn(Ga{sub 1-y}Al{sub y}){sub 2}O{sub 4}:Cr{sub 0.01}{sup 3+} (0{<=}y{<=}0.5). The blue shift and luminescent intensity variations of the charge transfer band and 3d-3d transitions in the spectra caused by Al substitution were related to larger band gap and stronger crystal field, respectively. The calculated crystal-field parameters indicated that Al incorporation enhanced the crystal field strength and induced more trigonal distortion due to different radii of Al{sup 3+} and Ga{sup 3+}.

Partial substitution of Zn Effects on the Structural and Electrical Properties of High Temperature Hg0.95Ag0.05Ba2Ca2Cu3O8+δ Superconductors

Science.gov (United States)

Abed, Noor S.; Fathi, Sabah J.; Jassim, Kareem A.; Mahdi, Shatha H.

2018-05-01

The effect of the Ag partial substitution at Hg site in HgOδ layer and Zn partial substitution at Ca site in CaO layer on the structure,Tc,electrical properties, and oxygen content for Hg-1223 have been studied. Bulk polycrystalline Hg1-xAgxBa2Ca2-yZnyCu3O8+δ compound samples with x=0.05 and y=0.0, 0.05, 0.1, 0.15, 0.2, 0.25, and 0.3, are synthesized by a solid state reaction process. Structural properties are studied by using X-ray powder pattern, the high temperature phase superconductor (Hg-1223) of the tetragonal structure didn't change with the partial substitution of Zn and Ag ions, lattice parameters c,c/a are established to vary with Ag and Zn- substitution. The surface morphology has been studied by using atomic force microscopes (AFM), showed that all specimens have good crystalline and homogeneous surface. Also give a best nano size value is 75.72 nm at x=0.05 and y=0.3. Four probe technique is used to measure Tc. The Tc were found to be increases from 129 K to 147 K and oxygen content were found to be increases with increasing Zn. In addition, dielectric properties (dielectric constant, dielectric loss factor, and the alternating electrical conductivity) are characterized directly by relating with Ag and Zn concentration.

Influence of La content on magnetic properties of Cu doped M-type strontium hexaferrite: Structural, magnetic, and Mossbauer spectroscopy study

Science.gov (United States)

Ghimire, M.; Yoon, S.; Wang, L.; Neupane, D.; Alam, J.; Mishra, S. R.

2018-05-01

The present study investigates the influence of Cu2+ and La3+-Cu2+ doping on the magnetic properties of Sr1-xLaxFe12-xCuxO19 (x = 0.0-0.5) hexaferrite (SrM) compounds. The samples were prepared via facile autocombustion technique followed by sintering. X-ray powder diffraction patterns show the formation of the pure phase of M-type hexaferrite for all x. Invariance in lattice parameters was observed with only Cu2+ substitution while lattice contraction along c-axis was observed with co-doping La3+-Cu2+ in SrM. The magnetic property of these compounds is explained based on Cu2+ occupancy in the absence and presence of La3+ in SrM magnetoplumbite structure. The Cu2+ doped SrFe12-xCuxO19 sample showed a monotonic decrease in Ms value while La3+-Cu2+ showed a noticeable increase in Ms value with x. Furthermore, while coercivity of Cu2+ doped SrM reduced with x, the coercivity of La3+-Cu2+ doped SrM showed a marked 12% increase in coercivity at x = 0.1 (Hc = 4391 Oe) from that of x = 0.0 (3918 Oe). Interestingly, Cu2+ doped SrM displayed invariance in Tc ∼ 458.6 °C with x, while La3+-Cu2+ doping reduced Tc by 5% from its x = 0 (Tc = 451.9 °C) to 429.6 °C. The room temperature Mossbauer spectral analysis confirmed a Cu2+ preference for the 12k site and its occupancy is observed to be influenced by the presence of La3+ ion at the Sr2+ site.

Effect of annealing temperature and substitution of Zr-Cu on magnetic properties of strontium hexaferrite nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Iqbal, Muhammad Javed; Ashiq, Muhammad Naeem [Department of Chemistry, Bahauddin Zakariya University Multan (Pakistan); Hernandez-Gomez, Pablo, E-mail: mjiqauchem@yahoo.co [Dpto. Electricidad y Electronica, Universidad de Valladolid, 47071 Valladolid (Spain)

2009-03-01

ZnTe and ZnTe:Cr films were prepared onto glass substrates using the thermal evaporation method. Structural properties of the prepared samples were analyzed using X-ray diffractometry, and the presence of a ZnCrTe phase was identified along with poor crystallinity. Composition analysis was done using XPS and the Cr content in the film was found to be 0.05 atomic percent. Transmittance spectra were recorded using UV-Vis spectrophotometry. The valence state of Cr in ZnTe:Cr film is determined to be +2 using electron spin resonance (ESR) spectroscopy. Magnetic moment data as a function of magnetic field were recorded using a Superconducting Quantum Interference Device (SQUID) magnetometer at temperatures of 5, 77 and 300 K. The results showed minority ferromagnetic behavior even at room temperature. Magnetic domains were observed using Magnetic Force Microscopy and the average domain size is 3.7 nm.

Exploratory studies of element substitutions in synthetic tetrahedrite. Part II. Selenium and tellurium as anions in Zn-Fe tetrahedrites

DEFF Research Database (Denmark)

Karup-Møller, Sven; Makovicky, E.

1999-01-01

-free) compositons do not materialize. The substituted Se tetrahedrite coexists with Cu3SbSe3, (iron-bearing) Cu2-xSe, Cu3SbSe4 plus/minus low Zn-sulfide melt. Selenium does not adopt the role of cation and tellurium that of anion in the tetrahedrite structure. The explanation of the severely restricted composition...

A comparison of the influence of different dopants on the radar-absorbing properties of barium hexaferrite

International Nuclear Information System (INIS)

Jones, M.; Suder, M.M.; Edge, A.J.J.; Stewart, G.A.; Hutchison, W.D.; Amiet, A.; Jewsbury, P.

2004-01-01

Full text: The ferromagnetic resonance of barium hexaferrite is at approximately 48 GHz, which sits well above the frequency bands employed by most radar systems. However, certain elements (or combinations of elements), when doped into the iron sub-lattice, have been observed to weaken the system's uniaxial magnetocrystalline anisotropy and thereby lower the ferromagnetic resonance frequency. This contribution presents a survey of ferromagnetic resonance frequencies published in the literature, as well as resonance frequencies that we have converted from published magnetic characterisations of the magnetic anisotropy. In several cases we have confirmed the reliability of such converted values, and new data will be presented for (Co 1/2 Zr 1/2 )- and (Co 1/2 Mo 1/2 )-doped barium hexaferrite. Our specimen materials were prepared by solid state reaction, and characterised using x-ray powder diffraction and 57 Fe Moessbauer spectroscopy. The electromagnetic response characteristics were recorded with a microwave network analyser, using either a co-axial specimen (0 - 18 GHz) or a larger, planar tile specimen (0 - 40 GHz). An ideal radar absorbing material would require just a small concentration of an inexpensive dopant to lower the ferromagnetic resonance frequency into the 0 - 2 GHz band that is typical of long-range radars. The likelihood of finding such a doped barium hexaferrite system will be discussed

Direct evidence for As as a Zn-site impurity in ZnO

CERN Document Server

Wahl, Ulrich; Correia, J G; Lourenço-Santana-Marques, Ana Claudia; Alves, E; Carvalho-Soares, José

2005-01-01

Arsenic has been reported in the literature as one of the few p-type dopants in the technologically promising II-VI semiconductor ZnO. However, there is an ongoing debate whether the p-type character is due to As simply replacing O atoms or to the formation of more complicated defect complexes, possibly involving As on Zn sites. We have determined the lattice location of implanted As in ZnO by means of conversion electron emission channeling from radioactive $^{73}$As. In contrast to what one might expect from its nature as a group V element, we find that As does not occupy substitutional O sites but in its large majority substitutional Zn sites. Arsenic in ZnO (and probably also in GaN) is thus an interesting example for an impurity in a semiconductor where the major impurity lattice site is determined by atomic size and electronegativity rather than its position in the periodic system.

Zn and Ni substitutional effects on spin fluctuations in YBa sub 2 Cu sub 3 O sub 7 by sup 6 sup 3 sup , sup 6 sup 5 Cu NQR

CERN Document Server

Han, K S; Mean, B J; Lee, K H; Seo, S W; Lee, M H; Lee, W C

2000-01-01

We have prepared Zn- and Ni-substituted YBa sub 2 Cu sub 3 O sub 7 (YBa sub 2 Cu sub 3 sub - sub x M sub x O sub 7 , M=Zn or Ni, x=0.00 approx 0.09) and performed sup 6 sup 3 sup , sup 6 sup 5 Cu nuclear quadrupole resonance (NQR) measurements for the plane site at 300 and 100 K. Substitutional effects on the relaxation rates are markedly different. Both the spin-lattice and the spin-spin relaxation rates decrease for Zn-doped YBCO. However, those increase for Ni-doped YBCO. This contrast in local electronic dynamics provides clear microscopic evidence that Zn forms no local moment while Ni develops a local moment. Consequently, the antiferromagnetic spin fluctuation is suppressed by Zn doping whereas it is preserved by Ni doping. This is also confirmed by the ratio of the sup 6 sup 3 sup , sup 6 sup 5 Cu spin-lattice relaxation rates for the plane coppers.

Dynamical properties and their strain-dependence of ZnSe(ZnSe:N: Zinc-blende and wurtzite

Directory of Open Access Journals (Sweden)

Dandan Wang

2014-06-01

Full Text Available The lattice dynamical properties of ZnSe and ZnSe with substitutional N incorporation(ZnSe:N are investigated in both the zinc-blend(ZB and wurtzite(WZ structures using first-principles calculations. The optical phonon modes of ZB-ZnSe at the Γ-point locate at 250 cm−1 for LO and 213 cm−1 for TO. The characteristic E2 phonon modes at about 50 cm−1 and the E1 and another E2 phonon modes around 200 cm−1 of WZ-ZnSe are suggested to be the fingerprint for distinguishing the two polytypes of ZnSe. For substitutional N incorporated ZnSe, the N incorporation introduces three new high energy modes above 500 cm−1, and the splitting of them is much larger in the WZ phase than that in ZB phase. The strain dependence of phonon frequency which could be useful for corresponding spectroscopic strain characterization are also studied. The simple linear dependence is determined for ZB-ZnSe, while the situation for WZ-ZnSe looks more complicated.

Analysis of the magnetic properties nanoscale barium hexaferrite (BHF) prepared by milling and ultrasonic method

International Nuclear Information System (INIS)

Novizal; Edie, Sasito; Manawan, Mykel T.E.

2016-01-01

Barium hexaferrite (BHF) is well established material which widely used respectively as permanent magnets. In this research, we report our recent investigation on magnetic properties analysis of barium hexaferrite (BHF) compounds with a ratio of Fe/Ba: 11 prepared by a mechanical alloying process and high power ultrasonic destruction to promote the soft magnetic properties. The investigation carried out by Scanning Electron Microscope (SEM) shows the grain size between 500-1500 nm, it indicates that each grain is composed of several crystallites or polycrystalline. By mean of X-ray diff raction revealed the phase composition and the mean crystallite size <70 nm. The Characterization of the magnetic properties of the effects of downsizing the particle size of ∼ 200 nm to ∼ 50 nm by the ultasonik method provide saturation value of 0.35 T, remanent 0.24 T and the coercivity is 115 kA / m. (paper)

Synthesis of visible light active Gd3+-substituted ZnFe2O4 nanoparticles for photocatalytic and antibacterial activities

Science.gov (United States)

Patil, S. B.; Bhojya Naik, H. S.; Nagaraju, G.; Viswanath, R.; Rashmi, S. K.

2017-08-01

In the present analysis, we study the assembly of a low-cost and visible light active ZnFe2-xGdxO4 ( x = 0 , 0.3, 0.5 and 0.7) nanoparticles (NPs) photocatalyst. The synthesized samples were characterized by several physicochemical techniques, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), UV-Visible absorption spectroscopy (UV-Vis), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The phase transition from cubic to orthorhombic was confirmed by XRD patterns. The increase in the concentration of Gd3+ substitution in ZnFe2O4 NPs enhances the redshift of absorption in the visible region of UV-Vis absorption spectra and reduces the band gap. In the photo-Fenton-type reaction, the gadolinium-substituted zinc ferrite (ZGF) NPs exhibit a significant catalytic activity for the degradation of methylene blue (99% in 90 minutes) under visible light (500W xenon lamp) with respect to bare samples (95% in 240 minutes) and they also show an excellent reusability nature. These materials were also screened for antibacterial activity against Gram-negative bacteria strains ( Pseudomonas aeruginosa and Escherichia coli).

Structure and optical properties of [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub m}

Energy Technology Data Exchange (ETDEWEB)

Eichhorn, Simon; Mader, Werner, E-mail: mader@uni-bonn.de

2016-01-15

Compounds of [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub 1} (x≤0.22) and [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub 2} (x≤0.42) were prepared by solid state processing proving a substantial solid solution of Sn in the layered compounds InGaO{sub 3}(ZnO){sub m} (m=1, 2). Single crystal X-ray diffraction of the compounds reveals two In{sup 3+} ions to be substituted by one Sn{sup 4+} and one Zn{sup 2+} at the octahedral layer preserving the average charge of +3 at these sites. The substitution does not lead to an ordering of the ions but proves for the first time that the octahedral site can be occupied by different ions while all characteristics of the layered structures remain unchanged. Consequences of indium substitution are (i) decrease of the a axis compared to InGaO{sub 3}(ZnO){sub m} according to smaller ionic radii of Sn{sup 4+} and Zn{sup 2+} compared to In{sup 3+} and (ii) shift of the optical band gap to higher energies shown by UV–vis measurements. - Graphical abstract: Substitution limits of indium in InGaO{sub 3}(ZnO){sub m} (IGZO) by Sn and Zn are studied for m=1, 2 by single crystal X-ray diffraction and micro-chemical analysis. - Highlights: • New Oxides [In{sub 1−2x}Sn{sub x}Zn{sub x}]GaO{sub 3}(ZnO){sub m} (m=1, 2) with IGZO type structure. • Sn and Zn substitute for In at octahedral sites. • Crystal structures were characterized by single crystal X-ray diffraction. • Optical band gap energies were determined by UV–vis spectroscopy.

PSynthesis, characterization and electromagnetic properties of Zn-substituted CoFe{sub 2}O{sub 4} via sucrose assisted combustion route

Energy Technology Data Exchange (ETDEWEB)

Gabal, M.A., E-mail: mgabalabdonada@yahoo.com [Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Al-Juaid, A.A.; Al-Rashed, S.M.; Hussein, M.A. [Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Al-Marzouki, F. [Physics Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia)

2017-03-15

Nanocrystalline Co{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} ferrites (0.0≤x≤0.1) were synthesized via simple, economic and environmentally friend sucrose auto-combustion method. An appropriate mechanism for complexation process as well as ferrites formation was suggested and discussed. The detailed structural studies were estimated through X-ray diffractometer (XRD), Fourier transform infrared spectroscopy (FT-IR) and transmission electron microscopy (TEM) measurements. The results confirmed the formation of mixed spinel phase with cubic structure and exhibited a gradual decrease in the crystal size from 58 nm to 20 nm by the addition of zinc. Based on the obtained structural parameters, an appropriate cation distribution was suggested and reinforced via electrical and magnetic properties measurements. Hysteresis loops measurements, indicated ferromagnetic characteristics, with hard magnetic properties, for the samples with 0.0≤x≤0.6. The samples with higher Zn-content exhibited paramagnetic properties. The changes in the magnetization and coercivity by the addition of zinc can be discussed in the view of the influence of cationic stoichiometry and magneto-crystalline anisotropy, respectively. The huge decrease in the magnetization value at x≥0.8 suggested a shift from ferromagnetic to paramagnetic characteristics. Ac-conductivity as well as dielectric constant behaviors reinforced this magnetic transition. The obtained Curie transition temperatures (T{sub C}) were gradually shifted to lower temperatures by the addition of zinc. The addition of zinc results in the substitution of Co{sup 2+} ions in the octahedral sites thus, decreases B-B hopping probability, decreases conductivity and consequently increases activation energy. The most predominant conduction mechanisms in the ferromagnetic and paramagnetic regions are expected to be due to electron hoppings between different valence state ions and small positive polaron migration, respectively. - Graphical

Structural and optical properties of ZnMgO nanostructures formed by Mg in-diffused ZnO nanowires

International Nuclear Information System (INIS)

Pan, C.-J.; Hsu, H.-C.; Cheng, H.-M.; Wu, C.-Y.; Hsieh, W.-F.

2007-01-01

ZnMgO nanostructures with wurtzite phase were prepared by thermal diffusion of Mg into the ZnO nanowires. As ZnO light-emitting devices have been operated by using ZnMgO layers as energy barrier layers to confine the carriers, it is essential to realize the characterization of ZnMgO particularly. In this work, the Mg content in Zn 1 -x Mg x O alloy determined by X-ray diffraction (XRD) and photoluminescence (PL) shows a good coincidence. The variation of lattice constant and the blueshift of near-band-edge emission indicate that Zn 2+ ions are successfully substituted by Mg 2+ ions in the ZnO lattice. In Raman-scattering studies, the change of E 2 (high) phonon line shape in ZnO:Mg nanostructures reveals the microscopic substitutional disorder. In addition to the host phonons of ZnO, two additional bands around 383 and 510 cm -1 are presumably attributed to the Mg-related vibrational modes. - Graphical abstract: We reported the synthesis of the ZnMgO nanostructures prepared by a simple vapor transport method. Magnesium-related anomalous modes are observed by Raman spectra for the first time in ZnMgO system

Electrical modulus and dielectric behavior of Cr{sup 3+} substituted Mg–Zn nanoferrites

Energy Technology Data Exchange (ETDEWEB)

Mansour, S.F.; Abdo, M.A.

2017-04-15

The dielectric parameters and ac electrical conductivity of Mg{sub 0.8}Zn{sub 0.2}Cr{sub x}Fe{sub 2−x}O{sub 4}; (0≤x≤0.025) nanoferrites synthesized citrate–nitrate auto-combustion method were studied using the complex impedance technique in the frequency and temperature ranges 4 Hz–5 MHz and 303–873 K respectively. Hopping of charge carriers plus interfacial polarization could interpret the behaviors of dielectric constant (ε′), dielectric loss tangent (tanδ) and ac electrical conductivity (σ{sub ac}) with frequency, temperatures and composition. The up-normal behavior observed in tanδ trend with temperatures confirms the presence of relaxation loss (dipoles losses). Correlated barrier hopping (CBH) of electron is the conduction mechanism of the investigated nanoferrites. Cole-Cole plots at different temperatures emphasize the main role of grain and grain boundaries in the properties of the investigated nanoferrites. Cr{sup 3+} substitution can control the dielectric parameters and ac electrical conductivity of Mg-Zn nanoferrites making it candidates for versatile applications. - Highlights: • The composition dependence of ε′, tanδ, and σ{sub ac} showed the same trend. • CBH model is the conduction mechanism of the investigated nanoferrite. • Cole-Cole plots confirmed the role of grain and grain boundaries in our nanoferrites.

Improvement of the magnetic moment of NiZn ferrites induced by substitution of Nd3+ ions for Fe3+ ions

Science.gov (United States)

Wu, Xuehang; Chen, Wen; Wu, Wenwei; Wu, Juan; Wang, Qing

2018-05-01

Four types of Ni-Zn based ferrites materials having the general formula Ni0.5Zn0.5NdxFe2-xO4 (0.0 ≤ x ≤ 0.12) have been successfully synthesized by calcining oxalates in air and the influence of Nd content on the structure and magnetic properties of Ni0.5Zn0.5NdxFe2-xO4 is studied. X-ray diffraction examination confirms that a high-crystallized Ni0.5Zn0.5NdxFe2-xO4 with cubic spinel structure is obtained when the precursor is calcined at 1000 °C in air for 2 h. The substitutions of Nd3+ ions for partial Fe3+ ions do not change the spinel crystalline structure of MFe2O4. The incorporation of Nd3+ ions in place of Fe3+ ions in Ni-Zn ferrites increases the average crystallite size. Specific saturation magnetization decreases with increase in Nd content. This is because Nd3+ ions with smaller magnetic moment preferentially fill the octahedral sites. In addition, antiferromagnetic FeNdO3 increases with increase in Nd content. In this study, Ni0.5Zn0.5Nd0.08Fe1.92O4, calcined at 1000 °C, exhibits the highest magnetic moment (4.2954 μB) and the lowest coercivity (28.82 Oe).

Luminescence enhancement of (Sr1-x Mx )2 SiO4 :Eu2+ phosphors with M (Ca2+ /Zn2+ ) partial substitution for white light-emitting diodes.

Science.gov (United States)

Wang, Yulong; Zhang, Wentao; Gao, Yang; Long, Jianping; Li, Junfeng

2017-02-01

Eu 2 + -doped Sr 2 SiO 4 phosphor with Ca 2 + /Zn 2 + substitution, (Sr 1-x M x ) 2 SiO 4 :Eu 2 + (M = Ca, Zn), was prepared using a high-temperature solid-state reaction method. The structure and luminescence properties of Ca 2 + /Zn 2 + partially substituted Sr 2 SiO 4 :Eu 2 + phosphors were investigated in detail. With Ca 2 + or Zn 2 + added to the silicate host, the crystal phase could be transformed between the α-form and the β-form of the Sr 2 SiO 4 structure. Under UV excitation at 367 nm, all samples exhibit a broad band emission from 420 to 680 nm due to the 4f 6 5d 1  → 4f 7 transition of Eu 2 + ions. The broad emission band consists of two peaks at 482 and 547 nm, which correspond to Eu 2 + ions occupying the ten-fold oxygen-coordinated Sr.(I) site and the nine-fold oxygen-coordinated Sr.(II) site, respectively. The luminescence properties, including the intensity and lifetime of Sr 2 SiO 4 :Eu 2 + phosphors, improved remarkably on Ca 2 + /Zn 2 + addition, and promote its application in white light-emitting diodes. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Structural and magnetic properties of conventional and microwave treated Ni–Zr doped barium strontium hexaferrite

International Nuclear Information System (INIS)

Kanagesan, S.; Jesurani, S.; Velmurugan, R.; Prabu, S.; Kalaivani, T.

2012-01-01

Highlights: ► Saturation magnetization increases whereas the coercivity decreases. ► The transition from hard phase to soft phase. ► Therefore, it is used for high-density magnetic recording applications. -- Abstract: M-type hexaferrites of component B 0.5 Sr 0.5 Fe 12−2x Ni x Zr x O 19 were investigated. The XRD patterns show single phase of the magnetoplumbite barium strontium ferrite and no other phases were present. Significant increase in line broadening of the XRD patterns was observed indicating a decrease of grain size. The samples exhibit well defined crystallization; all of them are hexagonal platelet grains. As the substitution level increased x = 0.2–0.8 mol%, the grains are agglomerated and the average diameter increased. The H c decreases remarkably with increasing Ni and Zr ions content. It was found that the particle size could be effectively decreased and coercivity H c could easily be controlled by varying the concentration (x) without significantly decreasing saturation magnetization. In particular, Ba 0.5 Sr 0.5 Fe 12−2x Ni x Zr x O 19 with x = 0.2, 0.4, 0.6, 0.8 mol% has suitable magnetic characteristics with particle size small enough for high-density magnetic recording applications.

Effect of the oxygen isoelectronic substitution in Cu2ZnSnS4 and its photovoltaic application

International Nuclear Information System (INIS)

Tablero, C.

2012-01-01

The optoelectronic properties of Cu 2 ZnSnS 4 and environmental considerations have attracted significant interest for photovoltaics. Using first-principles, we analyze the possible improvement of this material as a photovoltaic absorber via the isoelectronic substitution of S with O atoms. The evolution of the acceptor level is analyzed with respect to the atomic position of the nearest neighbors of the O atom. We estimate the maximum efficiency of this compound when used as a light absorber. The presence of the sub-band gap level below the conduction band could increases the solar-energy conversion with respect to the host. - Highlights: ► Cu 2 ZnSnS 4 is a promising material for low cost thin film solar cell technology. ► Its optoelectronic properties could be improved by states in the band gap. ► The oxygen to give rise to deep traps. ► Maximum efficiency can be larger than the host semiconductor.

Quenching of photoluminescence of colloidal ZnO nanocrystals by nitronyl nitroxide radicals

Energy Technology Data Exchange (ETDEWEB)

Stroyuk, Oleksandr L., E-mail: stroyuk@inphyschem-nas.kiev.ua [L.V. Pysarzhevsky Institute of Physical Chemistry of National Academy of Sciences of Ukraine, 31 Nauky avenue, 03028 Kyiv (Ukraine); Yakovenko, Anastasiya V.; Raevskaya, Oleksandra E. [L.V. Pysarzhevsky Institute of Physical Chemistry of National Academy of Sciences of Ukraine, 31 Nauky avenue, 03028 Kyiv (Ukraine); Plyusnin, Victor F. [Institute of Chemical Kinetics and Combustion of Siberian Branch of Russian Academy of Sciences, Novosibirsk (Russian Federation)

2014-11-15

Quenching of the photoluminescence of colloidal zinc oxide nanocrystals by a series of stable nitronyl nitroxide radicals was studied by means of stationary and time-resolved luminescence spectroscopy. Among the studied radicals the most efficient quenchers of the ZnO luminescence are the carboxyl-substituted species. The meta-substituted radical was found to be a more active quencher, than para-substituted one due to a closer proximity of the radical center to the nanocrystals surface. The PL quenching has a complex dynamic/static character. The dynamic quenching arises from photocatalytic radical reduction by ZnO conduction band electrons, while the static quenching is caused by adsorption of the photoreduction products on the nanocrystal surface. The non-substituted and OH-substituted radicals are inferior to the products of their photoreduction in capability of adsorption of the ZnO surface, and the quenching is dominated by interactions between the nanocrystals and photoreduced hydroxylamines. In case of COOH-substituted radicals, however, the radicals compete with the photoreduction products for the surface sites of ZnO nanocrystals resulting in a dynamic character of photoluminescence quenching.

Fine structure study on low concentration zinc substituted hydroxyapatite nanoparticles

International Nuclear Information System (INIS)

Hu, Wei; Ma, Jun; Wang, Jianglin; Zhang, Shengmin

2012-01-01

The fine structure of zinc substituted hydroxyapatite was studied using experimental analysis and first-principles calculations. The synthetic hydroxyapatite nanoparticles containing low Zn concentration show rod-like morphology. The crystallite sizes and unit-cell volumes tended to decrease with the increased Zn concentration according to X-ray diffraction patterns. The Zn K-edge X-ray absorption spectra and fitting results suggest that the hydroxyapatite doped with 0.1 mole% zinc is different in the zinc coordination environments compared with that containing more zinc. The density function theory calculations were performed on zinc substituted hydroxyapatite. Two mechanisms included replacing calcium by zinc and inserting zinc along the hydroxyl column and were investigated, and the related substitution energies were calculated separately. It is found that the substitution energies are negative and lowest for inserting zinc between the two oxygen atoms along the hydroxyl column (c-axis). Combined with the spectral analysis, it is suggested that the inserting mechanism is favored for low concentration zinc substituted hydroxyapatite. Highlights: ► We investigate the fine structure of hydroxyapatite with low content of Zn. ► XANES spectra are similar but a little different at low zinc content. ► Zinc ions influence hydroxyapatite crystal formation and lattice parameters. ► Formation energies are calculated according to plane-wave density function theory. ► Low content of zinc prefers to locate at hydroxyl column in hydroxyapatite lattice.

Structural, dielectric and gas sensing behavior of Mn substituted spinel MFe2O4 (M=Zn, Cu, Ni, and Co) ferrite nanoparticles

Science.gov (United States)

Ranjith Kumar, E.; Siva Prasada Reddy, P.; Sarala Devi, G.; Sathiyaraj, S.

2016-01-01

Spinel ferrite (MnZnFe2O4, MnCuFe2O4, MnNiFe2O4 and MnCoFe2O4) nanoparticles have been prepared by evaporation method. The annealing temperature plays an important role on changing particle size of the spinel ferrite nanoparticles was found out by X-ray diffraction and transmission electron microscopy. The role of manganese substitution in the spinel ferrite nanoparticles were also analyzed for different annealing temperature. The substitution of Mn also creates a vital change in dielectric properties have been measured in the frequency range of 100 kHz to 5 MHz. These spinel ferrites are decomposed to α-Fe2O3 after annealing above 550 °C in air. Through the characterization of the prepared powder, the effect of annealing temperature, chemical composition and preparation technique on the microstructure, particle size and dielectric properties of the Mn substituted spinel ferrite nanoparticles are discussed. Furthermore, Conductance response of Mn substituted MFe2O4 ferrite nanoparticles were measured by exposing the materials to reducing gas like liquefied petroleum gas (LPG).

Tailoring structure and magnetic characteristics of strontium hexaferrite via Al doping engineering

Energy Technology Data Exchange (ETDEWEB)

Wang, H.Z.; Hai, Y.N. [State Key Lab of High Power Semiconductor Laser of Changchun University Science and Technology, Changchun University Science and Technology, Changchun 130022 (China); Yao, B., E-mail: binyao@jlu.edu.cn [State Key Lab of Superhard Materials and Department of Physics, Jilin University, Changchun 130023 (China); Xu, Y. [School of Physics, Northeast Normal University, Changchun 130024 (China); Shan, L. [State Key Laboratory of Inorganic Synthesis and Preparative Chemistry and Department of Chemistry, Jilin University, Changchun 130012 (China); Xu, L.; Tang, J.L.; Wang, Q.H. [State Key Lab of High Power Semiconductor Laser of Changchun University Science and Technology, Changchun University Science and Technology, Changchun 130022 (China)

2017-01-15

Emerging structure and magnetic properties of Al{sup 3+}-modified SrFe{sub 12}O{sub 19} M-type hexaferrite system (SrAl{sub x}Fe{sub 12−x}O{sub 19}) had been studied in detail via doping engineering. With Al{sup 3+} ion nominal content ranging from 0 to 4 (0≤x≤4), the lattice parameters decrease due to the substitution of Fe{sup 3+} ions by smaller Al{sup 3+} ions, and the magnetization shows a continuous reduction with the increasing of Al content. For the coercivity, its value initially increases, reaching a maximum value of 16,876.9 Oe at x=3, and then reduces with the Al content further increase. When all the Fe{sup 3+} ions (x=4) are replaced by Al{sup 3+} ions, the net magnetic moment will be closed to zero, that will weaken the exchange interaction between Fe{sup 3+} ions, resulting in decrease of coercivity sharply and transformation ferrimagnetism into antiferromagnetism. The mechanism of the improvement of the magnetic properties induced by Al doping is discussed in the present work. - Highlights: • The coercivity reach a maximum value at x=3 in the SrAl{sub x}Fe{sub 12−x}O{sub 19}. • The coercivity of SrFe{sub 12}O{sub 19} increases due to nonmagnetic Al doping. • The saturation magnetization of SrFe{sub 12}O{sub 19} decreases due to nonmagnetic Al doping. • The transformation ferrimagnetism into antiferromagnetism by nonmagnetic Al doping.

Structural and magnetic properties of conventional and microwave treated Ni-Zr doped barium strontium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Kanagesan, S., E-mail: kanagu1980@gmail.com [Center for Materials Science and Nano Devices, Department of Physics, SRM University, Kattankulathur 603203, Tamil Nadu (India); Jesurani, S. [Center for Materials Science and Nano Devices, Department of Physics, SRM University, Kattankulathur 603203, Tamil Nadu (India); Department of Physics, Jeyaraj Annapackium College for Women, Periyakulam 625601, Tamil Nadu (India); Velmurugan, R. [Center for Materials Science and Nano Devices, Department of Physics, SRM University, Kattankulathur 603203, Tamil Nadu (India); Prabu, S. [Department of Chemistry, S.K.P. Engineering College, Anna University of Technology Chennai, Thiruvannamalai 606 611, Tamil Nadu (India); Kalaivani, T. [Center for Materials Science and Nano Devices, Department of Physics, SRM University, Kattankulathur 603203, Tamil Nadu (India)

2012-02-15

Highlights: Black-Right-Pointing-Pointer Saturation magnetization increases whereas the coercivity decreases. Black-Right-Pointing-Pointer The transition from hard phase to soft phase. Black-Right-Pointing-Pointer Therefore, it is used for high-density magnetic recording applications. -- Abstract: M-type hexaferrites of component B{sub 0.5}Sr{sub 0.5}Fe{sub 12-2x}Ni{sub x}Zr{sub x}O{sub 19} were investigated. The XRD patterns show single phase of the magnetoplumbite barium strontium ferrite and no other phases were present. Significant increase in line broadening of the XRD patterns was observed indicating a decrease of grain size. The samples exhibit well defined crystallization; all of them are hexagonal platelet grains. As the substitution level increased x = 0.2-0.8 mol%, the grains are agglomerated and the average diameter increased. The H{sub c} decreases remarkably with increasing Ni and Zr ions content. It was found that the particle size could be effectively decreased and coercivity H{sub c} could easily be controlled by varying the concentration (x) without significantly decreasing saturation magnetization. In particular, Ba{sub 0.5}Sr{sub 0.5}Fe{sub 12-2x}Ni{sub x}Zr{sub x}O{sub 19} with x = 0.2, 0.4, 0.6, 0.8 mol% has suitable magnetic characteristics with particle size small enough for high-density magnetic recording applications.

Structural and morphological evolution in magnetron co-sputtered (Zn, Cr)O films

International Nuclear Information System (INIS)

Hu, Y M; Chiou, J W; Han, T C; Chen, Y T; Hsu, C W; Chen, G J; Chou, W Y; Chang, J; Hsu, J Y; Yu, Y C

2008-01-01

In this study, x-ray diffraction, scanning electron microscopy, micro-Raman spectroscopy, x-ray absorption near-edge structure and particle-induced x-ray emission are used to characterize the microstructure of (Zn, Cr)O films prepared using a co-sputtering method. We found that the Cr ions did not substitute for the Zn sites but instead formed Cr nano-particles and secondary oxide phases (SOPs) of Cr 2 O 3 and/or ZnCr 2 O 4 in co-sputtered Zn 1-x Cr x O films with Cr content x ≥ 0.1. Evidence is presented for the evolution of SOPs formed in (Zn, Cr)O films with increasing Cr sputtering power. Based on the inspection of the Cr and Zn contents in (Zn, Cr)O films, we conclude that the formation of the Cr 2 O 3 phase is driven by a substantial increase in the atomic ratio of Cr/Zn, followed by the formation of a ZnCr 2 O 4 phase promoted by a higher content of Cr than of Zn in film with increasing Cr sputtering power. It seems that a strong preference of Cr for octahedral rather than tetrahedral coordination with oxygen would trigger the formation of SOPs rather than the substitution of Cr into Zn sites and could be an obstacle for achieving a real Cr-substituted ZnO dilute magnetic oxide.

Polyacrylamide Ferrogels with Magnetite or Strontium Hexaferrite: Next Step in the Development of Soft Biomimetic Matter for Biosensor Applications

Directory of Open Access Journals (Sweden)

Alexander P. Safronov

2018-01-01

Full Text Available Magnetic biosensors are an important part of biomedical applications of magnetic materials. As the living tissue is basically a “soft matter.” this study addresses the development of ferrogels (FG with micron sized magnetic particles of magnetite and strontium hexaferrite mimicking the living tissue. The basic composition of the FG comprised the polymeric network of polyacrylamide, synthesized by free radical polymerization of monomeric acrylamide (AAm in water solution at three levels of concentration (1.1 M, 0.85 M and 0.58 M to provide the FG with varying elasticity. To improve FG biocompatibility and to prevent the precipitation of the particles, polysaccharide thickeners—guar gum or xanthan gum were used. The content of magnetic particles in FG varied up to 5.2 wt % depending on the FG composition. The mechanical properties of FG and their deformation in a uniform magnetic field were comparatively analyzed. FG filled with strontium hexaferrite particles have larger Young’s modulus value than FG filled with magnetite particles, most likely due to the specific features of the adhesion of the network’s polymeric subchains on the surface of the particles. FG networks with xanthan are stronger and have higher modulus than the FG with guar. FG based on magnetite, contract in a magnetic field 0.42 T, whereas some FG based on strontium hexaferrite swell. Weak FG with the lowest concentration of AAm shows a much stronger response to a field, as the concentration of AAm governs the Young’s modulus of ferrogel. A small magnetic field magnetoimpedance sensor prototype with Co68.6Fe3.9Mo3.0Si12.0B12.5 rapidly quenched amorphous ribbon based element was designed aiming to develop a sensor working with a disposable stripe sensitive element. The proposed protocol allowed measurements of the concentration dependence of magnetic particles in gels using magnetoimpedance responses in the presence of magnetite and strontium hexaferrite ferrogels

Influence of stoichiometry on the magnetic disaccommodation in M-type Sr hexaferrites

International Nuclear Information System (INIS)

Hernandez-Gomez, Pablo; Torres, Carlos; Francisco, Carlos de; Munoz, J.M.; Alejos, Oscar; Iniguez, J.I.; Raposo, Victor

2004-01-01

The relaxation of the initial permeability has been measured in polycrystalline Sr hexaferrites with the initial composition SrO·nFe 2 O 3 (n=5.7, 6), prepared by means of standard ceramic techniques in air as well as CO 2 sintering atmospheres. The isochronal disaccommodation spectra show the presence of different relaxation processes, depending on both the sintering atmosphere and especially the initial composition, and associated to ionic reorientations of ferrous cations and lattice vacancies in the different metallic sites within the spinel (S) and hexagonal (R) blocks of the close packed lattice

Lattice sites of Na dopants in ZnO

CERN Document Server

AUTHOR|(CDS)2069243; Martins Correia, Joao; Amorim, Lígia; Decoster, Stefan; Ribeiro da Silva, Manuel; Da Costa Pereira, Lino Miguel

2016-01-01

The angular distribution of beta− particles emitted by the radioactive isotope 24Na was monitored following implantation into ZnO single crystals at fluences above 5E12 cm−2 at CERN’s ISOLDE facility. We identified sodium on two distinct sites: on substitutional Zn sites and on interstitial sites that are close to the so-called octahedral site. The interstitial Na was to large extent converted to substitutional Na already for annealing at 200°C, from which an activation energy of 0.8−1.3 eV, most likely around 1.2 eV, is estimated for the migration of interstitial Na in ZnO.

Lattice location of the group V elements Sb, As, and P in ZnO

CERN Document Server

Wahl, Ulrich; Mendonça, Tânia; Decoster, Stefan

2010-01-01

Modifying the properties of ZnO by means of incorporating antimony, arsenic or phosphorus impurities is of interest since these group V elements have been reported in the literature among the few successful p-type dopants in this technologically promising II-VI compound. The lattice location of ion-implanted Sb, As, and P in ZnO single crystals was investigated by means of the electron emission channeling technique using the radioactive isotopes $^{124}$Sb, $^{73}$As and $^{33}$P and it is found that they preferentially occupy substitutional Zn sites while the possible fractions on substitutional O sites are a few percent at maximum. The lattice site preference is understandable from the relatively large ionic size of the heavy mass group V elements. Unfortunately the presented results cannot finally settle the interesting issue whether substitutional Sb, As or P on oxygen sites or Sb$_{Zn}$−2V$_{Zn}$, As$_{Zn}$−2V$_{Zn}$ or P$_{Zn}$−2V$_{Zn}$ complexes (as suggested in the literature) are responsible f...

Synthesis, characterization and magnetic properties of MWCNTs decorated with Zn-substituted MnFe{sub 2}O{sub 4} nanoparticles using waste batteries extract

Energy Technology Data Exchange (ETDEWEB)

Gabal, M.A., E-mail: mgabalabdonada@yahoo.com [Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Al-Harthy, E.A. [Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia); Center of Excellence in Environmental Studies, King Abdulaziz University, PO Box 80216, Jeddah 21589 (Saudi Arabia); Al Angari, Y.M.; Abdel Salam, M.; Asiri, A.M. [Chemistry Department, Faculty of Science, King Abdulaziz University, Jeddah (Saudi Arabia)

2016-06-01

Mn{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} (x=0.2–0.8) nano-crystals, synthesized from recycling of Zn–C batteries, were successfully self-assembled alongside multi-walled carbon nanotubes (MWCNTs) via an environmentally friend sucrose auto-combustion method. The effect of Zn-content on structural and magnetic properties were investigated and discussed. XRD revealed the formation of single-phase ferrites. DTA–TG experiment showed that the auto-combustion reaction finished at about 350 {sup °}C. TEM exhibited that the MWCNTs are well decorated with ferrite particles. Hysteresis loop measurements revealed ferromagnetic behavior, with saturation magnetization decrease by the addition of MWCNTs or increasing Zn-Content. The kinetics of methylene blue dye (MB) removal using MWCNTs/Mn{sub 0.8}Zn{sub 0.2}Fe{sub 2}O nano-composite was investigated and discussed. - Graphical abstract: TEM image of MWCNTs/Mn{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} nano-composite showed that the MWCNTs were completely decorated with magnetic nanoparticles. The decoration passed through nucleation and growth processes in which nucleation of ferrite nanoparticles first takes place on the surface of MWCNTs followed by a subsequent growth of these nuclei. - Highlights: • Mn-Zn-ferrites were obtained via recycling process of spent Zn-C batteries. • Mn1−xZnxFe2O4/MWCNTS nano-composites were synthesized via sucrose combustion route. • Zn-substitution effect on structural and magnetic properties was investigated. • MWCNTs/Mn0.8Zn0.2Fe2O4 was investigated to remove MB dye from aqueous media.

Thermodynamic assessment of the Pr-Zn binary system

International Nuclear Information System (INIS)

Huang, X.M.; Liu, L.B.; Zhang, L.G.; Jia, B.R.; Jin, Z.P.; Zheng, F.

2008-01-01

On the basis of available experimental data of phase diagram and thermodynamic properties, the Pr-Zn binary system has been optimized using the CALPHAD approach. The phases, including liquid and bcc A 2(βPr) were treated as substitutional solutions, while the intermetallic compounds, including PrZn, PrZn 2 , PrZn 3 , Pr 3 Zn 11 , Pr 13 Zn 58 , Pr 3 Zn 22 , Pr 2 Zn 17 and PrZn 11 were modeled as stoichiometric compounds. As the result of optimization, a set of self-consistent thermodynamic parameters has been obtained, which can be used to reproduce the reported experimental data

Intrinsic labeling of alpha-fetoprotein with 65Zn

International Nuclear Information System (INIS)

Preiss, I.L.

1994-01-01

Many enzymes, proteins, and large molecules bind a variety of inorganic ions. The replacement of a specific metal ion with another element can disrupt the biodistribution and biochemistry of the host molecule. Alpha-fetoprotein (AFP) is a known oncofetal antigen. The authors have demonstrated that the substitution of Cu or Pb on AFP inhibits the transplacental migration of AFP and may lead to fetal demise. It is evident that in labeling with a radiotracer in order to observe the true distribution of a molecule, one must select a radioisotope of an element which is naturally bound to the host molecule. It has been demonstrated that AFP binds Zn in vivo. Thus, substituting 65 Zn for natural Zn produces an intrinsic label for AFP. The authors discuss the methodology for stripping and labeling of AFP with 65 Zn. The biodistribution of labeled AFP is compared with that of 65 Zn 2+ in healthy and diseased (hepatoma) animals

Trichomes of tobacco excrete zinc as zinc-substituted calcium carbonate and other zinc-containing compounds

International Nuclear Information System (INIS)

Sarret, G.; Harada, E.; Choi, Y-E.; Isaure, M.-P.; Geoffroy, N.; Fakra, S.; Marcus, M.A.; Birschwilks, M.; Clemens, S.; Manceau, A.

2006-01-01

Tobacco (Nicotiana tabacum L. cv Xanthi) plants were exposed to toxic levels of zinc (Zn). Zn exposure resulted in toxicity signs in plants, and these damages were partly reduced by a calcium (Ca) supplement. Confocal imaging of intracellular Zn using Zinquin showed that Zn was preferentially accumulated in trichomes. Exposure to Zn and Zn + Ca increased the trichome density and induced the production of Ca/Zn mineral grains on the head cells of trichomes. These grains were aggregates of submicrometer-sized crystals and poorly crystalline material and contained Ca as major element, along with subordinate amounts of Zn, manganese, potassium, chlorine, phosphorus, silicon, and magnesium. Micro x-ray diffraction revealed that the large majority of the grains were composed essentially of metal-substituted calcite (CaCO3). CaCO3 polymorphs (aragonite and vaterite) and CaC2O4 (Ca oxalate) mono- and dihydrate also were identified, either as an admixture to calcite or in separate grains. Some grains did not diffract, although they contained Ca, suggesting the presence of amorphous form of Ca. The presence of Zn-substituted calcite was confirmed by Zn K-edge micro-extended x-ray absorption fine structure spectroscopy. Zn bound to organic compounds and Zn-containing silica and phosphate were also identified by this technique. The proportion of Zn-substituted calcite relative to the other species increased with Ca exposure. The production of Zn-containing biogenic calcite and other Zn compounds through the trichomes is a novel mechanism involved in Zn detoxification. This study illustrates the potential of laterally resolved x-ray synchrotron radiation techniques to study biomineralization and metal homeostasis processes in plants

Effect of Ligand Substitution around the Dy(III) on the SMM Properties of Dual-Luminescent Zn-Dy and Zn-Dy-Zn Complexes with Large Anisotropy Energy Barriers: A Combined Theoretical and Experimental Magnetostructural Study.

Science.gov (United States)

Costes, Jean Pierre; Titos-Padilla, Silvia; Oyarzabal, Itziar; Gupta, Tulika; Duhayon, Carine; Rajaraman, Gopalan; Colacio, Enrique

2016-05-02

The new dinuclear Zn(II)-Dy(III) and trinuclear Zn(II)-Dy(III)-Zn(II) complexes of formula [(LZnBrDy(ovan) (NO3)(H2O)](H2O)·0.5(MeOH) (1) and [(L(1)ZnBr)2Dy(MeOH)2](ClO4) (3) (L and L(1) are the dideprotonated forms of the N,N'-2,2-dimethylpropylenedi(3-methoxysalicylideneiminato and 2-{(E)-[(3-{[(2E,3E)-3-(hydroxyimino)butan-2-ylidene ]amino}-2,2-dimethylpropyl)imino]methyl}-6-methoxyphenol Schiff base compartmental ligands, respectively) have been prepared and magnetostructurally characterized. The X-ray structure of 1 indicates that the Dy(III) ion exhibits a DyO9 coordination sphere, which is made from four O atoms coming from the compartmental ligand (two methoxy terminal groups and two phenoxido bridging groups connecting Zn(II) and Dy(III) ions), other four atoms belonging to the chelating nitrato and ovanillin ligands, and the last one coming to the coordinated water molecule. The structure of 3 shows the central Dy(III) ion surrounded by two L(1)Zn units, so that the Dy(III) and Zn(II) ions are linked by phenoxido/oximato bridging groups. The Dy ion is eight-coordinated by the six O atoms afforded by two L(1) ligands and two O atoms coming from two methanol molecules. Alternating current (AC) dynamic magnetic measurements of 1, 3, and the previously reported dinuclear [LZnClDy(thd)2] (2) complex (where thd = 2,2,6,6-tetramethyl-3,5-heptanedionato ligand) indicate single molecule magnet (SMM) behavior for all these complexes with large thermal energy barriers for the reversal of the magnetization and butterfly-shaped hysteresis loops at 2 K. Ab initio calculations on 1-3 show a pure Ising ground state for all of them, which induces almost completely suppressed quantum tunnelling magnetization (QTM), and thermally assisted quantum tunnelling magnetization (TA-QTM) relaxations via the first excited Kramers doublet, leading to large energy barriers, thus supporting the observation of SMM behavior. The comparison between the experimental and theoretical

Effect of sintering conditions on the magnetic disaccommodation in barium M-type hexaferrites

International Nuclear Information System (INIS)

Hernandez-Gomez, Pablo; Torres, Carlos; Francisco, Carlos de; Munoz, Jose Maria; Alejos, Oscar; Iniguez, Jose Ignacio; Raposo, Victor; Montero, Oscar

2006-01-01

The relaxation of the initial magnetic permeability has been measured in polycrystalline hexaferrites with nominal composition BaO.6Fe 2 O 3 (i.e. M-type). The samples have been sintered at different temperatures in CO 2 atmosphere and with different manufacturing conditions. In temperature range between 80 and 500 K, the magnetic disaccommodation shows presence of different relaxation processes, depending on both the sintering temperature and sintering time. The analogies and differences between the results obtained are discussed in terms of similar phase formation and different crystallite size

Influence of dysprosium addition on the structural, morphological ...

Indian Academy of Sciences (India)

Microwave absorption properties of hexaferrite (70 wt%)–acrylic resin. (30 wt%) composites ... the RE ions were substituted for Sr (Ba) or Fe, taking into accounts the .... general the RE substitutions weaken the super exchange interactions ...

The mechanically induced structural disorder in barium hexaferrite, BaFe12O19, and its impact on magnetism

CERN Document Server

Šepelák, V; Witte, R; Röder, J; Menzel, D; Schuster, R H; Hahn, H; Heitjans, P; Becker, K-D

2014-01-01

The response of the structure of the M-type barium hexaferrite (BaFe12O19) to mechanical action through high-energy milling and its impact on the magnetic behaviour of the ferrite are investigated. Due to the ability of the Fe-57 Mossbauer spectroscopic technique to probe the environment of the Fe nuclei, a valuable insight on a local atomic scale into the mechanically induced changes in the hexagonal structure of the material is obtained. It is revealed that the milling of BaFe12O19 results in the deformation of its constituent polyhedra (FeO6 octahedra, FeO4 tetrahedra and FeO5 triangular bi-pyramids) as well as in the mechanically triggered transition of the Fe3+ cations from the regular 12k octahedral sites into the interstitial positions provided by the magnetoplumbite structure. The response of the hexaferrite to the mechanical treatment is found to be accompanied by the formation of a non-uniform nanostructure consisting of an ordered crystallite surrounded/separated by a structurally disordered surfac...

Evaluation of structural, morphological and magnetic properties of CuZnNi (Cu_xZn_0_._5_−_xNi_0_._5Fe_2O_4) nanocrystalline ferrites for core, switching and MLCI’s applications

International Nuclear Information System (INIS)

Akhtar, Majid Niaz; Khan, Muhammad Azhar; Ahmad, Mukhtar; Nazir, M.S.; Imran, M.; Ali, A.; Sattar, A.; Murtaza, G.

2017-01-01

The influence of Cu substitution on the structural and morphological characteristics of Ni–Zn nanocrystalline ferrites have been discussed in this work. The detailed and systematic magnetic characterizations were also done for Cu substituted Ni–Zn nanoferrites. The nanocrystalline ferrites of Cu substituted Cu_xZn_0_._5_−_xNi_0_._5Fe_2O_4 ferrites (x=0, 0.1, 0.2, 0.3, 0.4 and 0.5) were synthesized using sol gel self-combustion hybrid method. X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Transmission electron microscope (TEM) and Vibrating sample magnetometer (VSM) were used to investigate the properties of Cu substituted nanocrystalline ferrites. Single phase structure of Cu substituted in Ni–Zn nanocrystalline ferrites were investigated for all the samples. Crystallite size, lattice constant and volume of the cell were found to increase by increasing Cu contents in spinel structure. The better morphology with well-organized nanocrystals of Cu–Zn–Ni ferrites at x=0 and 0.5 were observed from both FESEM and TEM analysis. The average grain size was 35–46 nm for all prepared nanocrystalline samples. Magnetic properties such as coercivity, saturation, remanence, magnetic squareness, magneto crystalline anisotropy constant (K) and Bohr magneton were measured from the recorded M–H loops. The magnetic saturation and remanence were increased by the incorporation of Cu contents. However, coercivity follow the Stoner-Wolforth model except for x=0.3 which may be due to the site occupancy and replacement of Cu contents from octahedral site. The squareness ratio confirmed the super paramgnetic behaviour of the Cu substituted in Ni–Zn nanocrystalline ferrites. Furthermore, Cu substituted Ni–Zn nanocrystalline ferrites may be suitable for many industrial and domestic applications such as components of transformers, core, switching, and MLCI’s due to variety of the soft magnetic characteristics. - Highlights: • Cu substituted

Synthesis, characterization and magnetic properties of monodisperse Ni, Zn-ferrite nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Kumar, Sanjeev, E-mail: sanjeevkumar.dubey2@gmail.com [University of Petroleum and Energy Studies, Dehradun, Uttarakhand (India); Kumar, Pankaj [University of Petroleum and Energy Studies, Dehradun, Uttarakhand (India); Singh, Vaishali [University School of Basic and Applied Science (India); Kumar Mandal, Uttam [University of Chemical Technology, GGS Indraprastha University, Sector 16, Dwarka, Delhi 110403 (India); Kumar Kotnala, Ravinder [National Physical laboratory, New Delhi 110012 (India)

2015-04-01

Synthesization of monodisperse Ni, Zn-ferrite (Ni{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4}, x=1, 0.8, 0.6, 0.5, 0.4, 0.2, 0.0) nanocrystals has been achieved by the inverse microemulsion method using CTAB as surfactant and kerosene as an oil phase. The detailed characterization of the synthesized nanocrystals and measurement of the magnetic properties has been done by techniques like X-ray diffraction (XRD), field emission transmission electron microscopy (FETEM), Fourier transform infrared spectroscopy (FITR) and Vibrating Sample Magnetometer (VSM) respectively. The relationship between the structure and composition of the nanocrystals with magnetic properties has been investigated. The nanocrystals size is found to be in the range 1–5 nm. The effect of Zn substitution on size and magnetic properties has been studied. It has been observed that magnetism changed from ferromagnetic at X= 0 to super paramagnetic to paramagnetic at X=1 as Zn concentration increased. The Curie temperature is found to decrease with an increase in Zn concentration. - Highlights: • Reverse microemulsion route is very facile route for synthesis of Ni{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} ferrite. • Presence of Zn changes the structural and magnetic properties of the Zn substituted NiFe{sub 2}O{sub 4.} • The lattice constant increases with the increase in Zn substitution. • The curie temperature decreases with Zn concentration appreciably. • Magnetic behavior varies from ferromagnetic at x=0 to superparamagnetic to paramagnetic at x=1.

Barium hexaferrite nanoparticles: Synthesis and magnetic properties

International Nuclear Information System (INIS)

Martirosyan, K.S.; Galstyan, E.; Hossain, S.M.; Wang Yiju; Litvinov, D.

2011-01-01

Carbon combustion synthesis is applied to rapid and energy efficient fabrication of crystalline barium hexaferrite nanoparticles with the average particle size of 50-100 nm. In this method, the exothermic oxidation of carbon nanoparticles with an average size of 5 nm with a surface area of 80 m 2 /g generates a self-propagating thermal wave with maximum temperatures of up to 1000 deg. C. The thermal front rapidly propagates through the mixture of solid reactants converting it to the hexagonal barium ferrite. Carbon is not incorporated in the product and is emitted from the reaction zone as a gaseous CO 2 . The activation energy for carbon combustion synthesis of BaFe 12 O 19 was estimated to be 98 kJ/mol. A complete conversion to hexagonal barium ferrite is obtained for carbon concentration exceeding 11 wt.%. The magnetic properties H c ∼3000 Oe and M s ∼50.3 emu/g of the compact sintered ferrites compare well with those produced by other synthesis methods.

Synthesis, structural investigation and magnetic properties of Zn2+ substituted cobalt ferrite nanoparticles prepared by the sol–gel auto-combustion technique

International Nuclear Information System (INIS)

Raut, A.V.; Barkule, R.S.; Shengule, D.R.; Jadhav, K.M.

2014-01-01

Structural morphology and magnetic properties of the Co 1−x Zn x Fe 2 O 4 (0.0≤x≥1.0) spinel ferrite system synthesized by the sol–gel auto-combustion technique using nitrates of respective metal ions have been studied. The ratio of metal nitrates to citric acid was taken at 1:3. The as prepared powder of cobalt zinc ferrite was sintered at 600 °C for 12 h after TG/DTA thermal studies. Compositional stoichiometry was confirmed by energy dispersive analysis of the X-ray (EDAX) technique. Single phase cubic spinel structure of Co–Zn nanoparticles was confirmed by XRD data. The average crystallite size (t), lattice constant (a) and other structural parameters of zinc substituted cobalt ferrite nanoparticles were calculated from XRD followed by SEM and FTIR. It is observed that the sol–gel auto-combustion technique has many advantages for the synthesis of technologically applicable Co–Zn ferrite nanoparticles. The present investigation clearly shows the effect of the synthesis method and possible relation between magnetic properties and microstructure of the prepared samples. Increase in nonmagnetic Zn 2+ content in cobalt ferrite nanoparticles is followed by decrease in n B , M s and other magnetic parameters. Squareness ratio for the Co-ferrite was 1.096 at room temperature. - Highlights: • Co–Zn nanoparticles are prepared by sol–gel auto-combustion method. • Structural properties were characterized by XRD, SEM, and FTIR. • Compositional stoichiometry was confirmed by EDAX analysis. • Magnetic parameters were measured by the pulse field hysteresis loop technique

Paramagnetism and antiferromagnetic interactions in single-phase Fe-implanted ZnO

CERN Document Server

Pereira, Lino Miguel da Costa; Correia, João Guilherme; Van Bael, M J; Temst, Kristiaan; Vantomme, André; Araújo, João Pedro

2013-01-01

As the intrinsic origin of the high temperature ferromagnetism often observed in wide-gap dilute magnetic semiconductors becomes increasingly debated, there is a growing need for comprehensive studies on the single-phase region of the phase diagram of these materials. Here we report on the magnetic and structural properties of Fe-doped ZnO prepared by ion implantation of ZnO single crystals. A detailed structural characterization shows that the Fe impurities substitute for Zn in ZnO in a wurtzite Zn$_{1−x}$Fe$_{x}$O phase which is coherent with the ZnO host. In addition, the density of beam-induced defects is progressively decreased by thermal annealing up to 900$^{\\circ}$C, from highly disordered after implantation to highly crystalline upon subsequent annealing. Based on a detailed analysis of the magnetometry data, we demonstrate that isolated Fe impurities occupying Zn substitutional sites behave as localized paramagnetic moments down to 2$^{\\circ}$K, irrespective of the Fe concentration and the density...

Attainment of barium hexaferrite nanoparticles by a Pechini Method

International Nuclear Information System (INIS)

Galvao, S.B.; Timoteo, Jr.J.F.; Melo, G.M.; Souto, K.K.O.; Florioto, N.T.; Paskocimas, C.A.

2009-01-01

The barium hexaferrites (BaFe 12 O 19 ) are used as a compound of materials applied in electronic devices, as medical devices, satellites, dada servers systems, wireless systems and others. The general properties are strongly related to the microstructure and morphology, and the particles size decrease results in advantages to the majority applications, mainly the high-tech thumbnail devices. These magnetic ceramic materials, with perovskite structure, are traditionally prepared my conventional oxide mixture synthesis. In this work was studied the nanoparticle synthesis of BaFe 12 O 19 by the precursors polymeric method (Pechini), using as precursors the barium carbonate and the iron nitrate, under different thermal treatment conditions. The samples were characterized by XRD, SEM, BET, DTA and TGA. The results presented the attainment of a monophasic powder with particles size around 100 nm. (author)

Cation substitution induced blue-shift of optical band gap

Indian Academy of Sciences (India)

Cation substitution induced blue-shift of optical band gap in nanocrystalline Zn ( 1 − x ) Ca x O thin films deposited by sol–gel dip coating technique ... thin films giving 13.03% enhancement in theenergy gap value due to the electronic perturbation caused by cation substitution as well as deterioration in crystallinity.

Lattice location of implanted As in ZnO

CERN Document Server

Wahl, U; Correia, J G; Marques, A C; Alves, E; Soares, J C

2007-01-01

Radioactive 73As ions were implanted into a ZnO single crystal at room temperature with 60 keV up to a fluence of 2×1013 cm−2. Subsequently, the angular emission channeling patterns of emitted conversion electrons were recorded by means of a position-sensitive detector in the as-implanted state and following annealing up to 900 C, and were compared to simulated emission yields for a variety of different lattice sites. We find that As does not occupy substitutional O sites, but mainly occupies the substitutional Zn sites. The fraction of As on O sites was at most a few per cent. Arsenic in ZnO is thus an interesting example of an impurity in a semiconductor where the major impurity lattice site is determined by atomic size and electronegativity rather than its position in the periodic system. Possible consequences with respect to the role of arsenic as a p-type dopant in ZnO are being discussed.

Effect of neodymium substitutions on electromagnetic properties in low temperature sintered NiCuZn ferrite

Science.gov (United States)

Wu, C. P.; Tung, M. J.; Ko, W. S.; Wang, Y. P.; Tong, S. Y.; Yang, M. D.

2015-11-01

Nd3+ ions substituted Ni0.37Cu0.14Zn0.52Fe2O4 (Nd3+ ions content=0, 0.01, 0.04, 0.6, 1.5 wt%) were prepared by the usual standard ceramic method at 1030 °C sintering temperature, and the composition dependence of the physical and magnetic properties has been investigated. SEM micrographs and EDX analysis revealed that it is no obvious impurities up to Nd3+ ions content wt%=0.04. For higher Nd3+ ions content samples (0.6 and 1.5 wt%), there are two kind of impurities Cu-rich and Nd-rich iron oxide phase. The saturation magnetization of the 0.01 wt% Nd3+ions content sample is higher as result of that the A-B sites distance and YK-angles are shorter and smaller. The saturation magnetization of 0.04-1.5 wt% Nd3+ ion content sample are reduced, since the total magnetic moments of the AB site are decreased. For the 0.6 wt% sample, the Curie temperature increasing is as result of the Cu-rich iron oxide separating out. The maximum enhancements of permeability μ‧ are improved to 11.2% (0.04 wt%) and 29.2% (0.6 wt%) at the 6.7 and 13.8 MHz, respectively. However, it is notice that small amount substitutions of Nd3+ increase the high frequency electromagnetic characteristics, can be applied to NFC technology and WPT technologies.

Microwave absorption and {sup 57}Fe Mössbauer properties of Ni-Ti doped barium hexaferrite

Energy Technology Data Exchange (ETDEWEB)

Harker, S. J., E-mail: stephen.harker@defence.gov.au [Russell Offices, Program Office, Defence Science and Technology Organisation (Australia); Stewart, G. A.; Hutchison, W. D. [UNSW Canberra at the Australian Defence Force Academy, School of Physical, Environmental and Mathematical Sciences (Australia); Amiet, A. [Defence Science and Technology Organisation, Maritime Division (Australia); Tucker, D. [UNSW Canberra at the Australian Defence Force Academy, School of Physical, Environmental and Mathematical Sciences (Australia)

2015-04-15

The impact of doping the Fe component of barium hexaferrite with Ni{sub 0.5}Ti{sub 0.5} is investigated using x-ray powder diffraction, {sup 57}Fe Mössbauer spectroscopy and microwave network analysis. The dopant ions exhibit a preference for the 2b, 4f{sub 2} and 12k-sites and the unit cell volume is observed to decrease. The ferromagnetic resonance frequency is reduced by about 11.5 GHz for each additional dopant ion per formula unit.

Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

International Nuclear Information System (INIS)

Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

2004-01-01

Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

Microstructural and magnetic studies on BaMg{sub x}Zn{sub x}X{sub 2x}Fe{sub 12−4x}O{sub 19} (X=Zr,Ce,Sn) prepared via mechanical activation method to act as a microwave absorber in X-band

Energy Technology Data Exchange (ETDEWEB)

Afghahi, Seyyed Salman Seyyed [Department of Engineering, Imam Hossein University, Tehran (Iran, Islamic Republic of); Jafarian, Mojtaba, E-mail: m.jafarian@iau-shahrood.ac.ir [Department of Material Engineering, South Tehran Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Atassi, Yomen [Department of Applied Physics, Higher Institute for Applied Sciences and Technology, Damascus (Syrian Arab Republic)

2016-05-15

In this study, doped barium hexaferrite with the composition of BaMg{sub x}Zn{sub x}X{sub 2x}Fe{sub 12−4x}O{sub 19} (where x= 0.3, 0.5, 0.7, 0.9 and X= Zr, Ce, Sn) was prepared via mechanical activation. X-ray diffractometer (XRD), FTIR spectrophotometer, Field emission scanning electron microscope (FE-SEM), vibrating sample magnetometer (VSM) and vector network analyzer (VNA) were used to analyze its phases, structure, electromagnetic and microwave absorption properties respectively. Based on the results, single phase barium hexaferrite was obtained in all cases after milling the mixed powders for 20 h plus calcination at 1000 °C for 5 h. Morphology of the particles in all of the doped samples was completely hexagonal shape and they had an appropriate distribution. It was found that the sample of BaMg{sub 0.9}Zn{sub 0.9}Zr{sub 1.8}Fe{sub 8.4}O{sub 19} with saturation magnetization and coercive force of 37.3 emu/g and 94 Oe respectively possessed the maximum reflection loss of −19.3 dB at 12.3 GHz with 1.7 GHz bandwidth. - Highlights: • The mechanical activation method was used to prepare: BaMg{sub x}Zn{sub x}X{sub 2x}Fe{sub 12−4x}O{sub 19}(X=Zr, Ce, and Sn) with values of xequal to 0.3, 0.5, 0.7, and 0.9. • Morphology of the particles in all of the doped samples was completely hexagonal shape and they had an appropriate distribution. • BaMg{sub 0.9}Zn{sub 0.9}Zr{sub 1.8}Fe{sub 8.4}O{sub 19} possesses the maximum reflection loss of −19.3 dB at 12.3 GHz with 1.7 GHz bandwidth.

Magnetic properties of Mn-doped ZnO diluted magnetic semiconductors

International Nuclear Information System (INIS)

Liu Xuechao; Zhang Huawei; Zhang Tao; Chen Boyuan; Chen Zhizhan; Song Lixin; Shi Erwei

2008-01-01

A series of Mn-doped ZnO films have been prepared in different sputtering plasmas by using the inductively coupled plasma enhanced physical vapour deposition. The films show paramagnetic behaviour when they are deposited in an argon plasma. The Hall measurement indicates that ferromagnetism cannot be realized by increasing the electron concentration. However, the room-temperature ferromagnetism is obtained when the films are deposited in a mixed argon-nitrogen plasma. The first-principles calculations reveal that antiferromagnetic ordering is favoured in the case of the substitution of Mn 2+ for Zn 2+ without additional acceptor doping. The substitution of N for O (N O −) is necessary to induce ferromagnetic couplings in the Zn-Mn-O system. The hybridization between N 2p and Mn 3d provides an empty orbit around the Fermi level. The hopping of Mn 3d electrons through the empty orbit can induce the ferromagnetic coupling. The ferromagnetism in the N-doped Zn-Mn-O system possibly originates from the charge transfer between Mn 2+ and Mn 3+ via N O − . The key factor is the empty orbit provided by substituting N for O, rather than the conductivity type or the carrier concentration

Cation distribution in Ni-substituted Mn{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} nanoparticles: A Raman, Mössbauer, X-ray diffraction and electron spectroscopy study

Energy Technology Data Exchange (ETDEWEB)

Thota, Suneetha [Microwave Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Kashyap, Subhash C., E-mail: skashyap@physics.iitd.ac.in [Microwave Laboratory, Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Sharma, Shiv K. [Hawaii Institute of Geophysics and Planetology, University of Hawaii (UH), Honolulu, HI 96822 (United States); Reddy, V.R. [UGC-DAE Consortium for Scientific Research, Khandwa Road, Indore 452017 (India)

2016-04-15

Graphical abstract: - Highlights: • Synthesized Mn{sub 0.5−x}Ni{sub x}Zn{sub 0.5}Fe{sub 2}O{sub 4}, nanoparticles (0.05 ≤ x ≤ 0.45) at low temperature. • Raman studies established that Fe and Zn ions occupy A site in equal fraction. • {sup 57}Fe Mossbauer study revealed that Ni and Mn ions occupy nearly 25% of B sites. • Electron spectroscopy (XPS) confirmed that nearly 25% Fe{sup 3+} dwells at A sites. • Diffraction peak intensity (X-ray) quantified cations distribution at A- and B-sites. - Abstract: In this paper we report the structural, vibration, and electronic-structure parameters (bonding and valence of cations) of single phase cubic mixed spinel nanoparticles of (Zn{sub δ}Mn{sub γ}Fe{sub 1−(γ+δ)})[Ni{sub x}Zn{sub 0.5−δ}Mn{sub 0.5−γ−x}Fe{sub 1+(γ+δ)}]O{sub 4} where x = 0.05–0.45 with an aim to determine cation-distribution i.e. δ and γ in these samples. The Raman spectroscopy has established that only Fe and Zn cations occupy tetrahedral interstitial sites in a FCC anion lattice in nearly equal fraction, and Mössbauer spectra have shown that Fe{sup 3+} cations are present at both, tetrahedral and octahedral interstitial sites and Ni{sup 2+} cations are situated at the octahedral sites in all the substituted samples. The photoelectron spectra also revealed the presence of Fe{sup 3+} cations at both the interstitial sites. The best possible cationic distribution in Ni substituted Mn–Zn ferrites has been estimated by reiteratively calculating the intensity ratios of various pairs of X-ray diffraction peaks and matching with the observed intensity ratios.

Electronic and atomic structure of complex defects in Al- and Ga-highly doped ZnO films

Energy Technology Data Exchange (ETDEWEB)

Menéndez-Proupin, Eduardo [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Departamento de Física, Facultad de Ciencias, Universidad de Chile, Las Palmeras 3425, 780-0003 Ñuñoa, Santiago (Chile); Palacios, Pablo, E-mail: pablo.palacios@upm.es [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Dpt. FAIAN, E.T.S.I. Aeronáutica y del Espacio, UPM, Pz. Cardenal Cisneros 3, 28040 Madrid (Spain); Wahnón, Perla [Instituto de Energía Solar, Universidad Politécnica de Madrid (UPM), Ciudad Universitaria, 28040 Madrid (Spain); Dpt. TFO, E.T.S.I. Telecomunicación, UPM, Ciudad Universitaria, 28040 Madrid (Spain)

2015-06-15

Point defects in Ga- and Al-doped ZnO thin films are studied by means of first principles electronic structure calculations. Candidate defects are identified to explain recently observed differences in electrical and spectroscopic behavior of both systems. Substitutional doping in Ga–ZnO explain the metallic behavior of the electrical properties. Complexes of interstitial oxygen with substitutional Ga can behave as acceptor and cause partial compensation, as well as gap states below the conduction band minimum as observed in photoemission experiments. Zn vacancies can also act as compensating acceptors. On the other hand, the semiconducting behavior of Al–ZnO and the small variation in the optical gap compared with pure ZnO, can be explained by almost complete compensation between acceptor Zn vacancies and substitutional Al donors. Interstitial Al can also be donor levels and can be the origin of the small band observed in photoemission experiments below the Fermi level. Combinations of substitutional Al with interstitial oxygen can act simultaneously as compensating acceptor and generator of the mentioned photoemission band. The theoretical calculations have been done using density functional theory (DFT) within the generalized gradient approximation with on-site Coulomb interaction. In selected cases, DFT calculations with semilocal-exact exchange hybrid functionals have been performed. Results explain photoelectron spectra of Ga–ZnO and Al–ZnO at the corresponding doping levels. - Highlights: • Defects in Ga- and Al-heavy-doped ZnO films are studied by quantum calculations. • Defects compatible with electrical, optical, and HAXPES spectra are proposed. • Doping efficiency is reduced by Zn vacancies and O interstitials. • HAXPES bands near the Fermi level are induced by Al{sub i}, and complexes Ga{sub Zn}-O{sub i}, and Al{sub Zn}-O{sub i}.

The leguminous species Anthyllis vulneraria as a Zn-hyperaccumulator and eco-Zn catalyst resources.

Science.gov (United States)

Grison, Claire M; Mazel, Marine; Sellini, Amandine; Escande, Vincent; Biton, Jacques; Grison, Claude

2015-04-01

Anthyllis vulneraria was highlighted here as a Zn-hyperaccumulator for the development of a pilot phytoextraction process in the mine site of Les Avinières in the district of Saint-Laurent-Le-Minier. A. vulneraria appeared to hyperaccumulate the highest concentration of Zn in shoots with a better metal selectivity relative to Cd and Pb than the reference Zn-hyperaccumulator Noccea caerulescens. A bigger biomass production associated to a higher Zn concentration conducted A. vulneraria to the highest total zinc gain per hectare per year. As a legume, A. vulneraria was infected by rhizobia symbionts. Inoculation of A. vulneraria seeds showed a positive impact on Zn hyperaccumulation. A large-scale culture process of symbiotic rhizobia of A. vulneraria was investigated and optimized to allow large-scale inoculation process. Contaminated shoots of A. vulneraria were not considered as wastes and were recovered as Eco-Zn catalyst in particular, examples of organic synthesis, electrophilic aromatic substitution. Eco-Zn catalyst was much more efficient than conventional catalysts and allowed greener chemical processes.

Effect of calcination temperature on microstructure, dielectric, magnetic and optical properties of Ba0.7La0.3Fe11.7Co0.3O19 hexaferrites

International Nuclear Information System (INIS)

Kaur, Talwinder; Kaur, Barjinder; Bhat, Bilal H.; Kumar, Sachin; Srivastava, A.K.

2015-01-01

M-type barium hexaferrite Ba 0.7 La 0.3 Fe 11.7 Co 0.3 O 19 (BaLCM) powder, synthesized using sol gel auto combustion method, heat treated at 700, 900, 1100 and 1200 °C. X ray diffraction (XRD) powder patterns of heat treated samples show the formation of pure phase of M-type hexaferrite after 700 °C. Thermo gravimetric analysis (TGA) reveals that the weight loss of BaLCM becomes constant after 680 °C. The presence of two prominent peaks, at 432 cm −1 and 586 cm −1 in Fourier Transform Infrared Spectroscopy (FT-IR) spectra, gives the idea of formation of M-type hexaferrites. The M–H curve obtained from Vibrating Sample Magnetometer (VSM) were used to calculate saturation magnetization (M S ), retentivity (M r ), squareness ration (SR) and coercivity (H c ). The maximum value of coercivity (5602 Oe) is found at 900 °C. The band gap dependency on temperature was studied using UV–vis NIR spectroscopy. The dielectric constant has been found to be high at low frequency but it decreases with increase in frequency. Such kind of dielectric behavior is explained on the basis of Koop's phenomenological theory and Maxwell Wagner theory

Hyperfine magnetic fields in substituted Finemet alloys

Energy Technology Data Exchange (ETDEWEB)

Brzózka, K., E-mail: k.brzozka@uthrad.pl [University of Technology and Humanities in Radom, Department of Physics (Poland); Sovák, P. [P.J. Šafárik University, Institute of Physics (Slovakia); Szumiata, T.; Gawroński, M.; Górka, B. [University of Technology and Humanities in Radom, Department of Physics (Poland)

2016-12-15

Transmission Mössbauer spectroscopy was used to determine the hyperfine fields of Finemet-type alloys in form of ribbons, substituted alternatively by Mn, Ni, Co, Al, Zn, V or Ge of various concentration. The comparative analysis of magnetic hyperfine fields was carried out which enabled to understand the role of added elements in as-quenched as well as annealed samples. Moreover, the influence of the substitution on the mean direction of the local hyperfine magnetic field was examined.

Experimental study of the Ca–Mg–Zn system using diffusion couples and key alloys

Directory of Open Access Journals (Sweden)

Yi-Nan Zhang, Dmytro Kevorkov, Florent Bridier and Mamoun Medraj

2011-01-01

Full Text Available Nine diffusion couples and 32 key samples were prepared to map the phase diagram of the Ca–Mg–Zn system. Phase relations and solubility limits were determined for binary and ternary compounds using scanning electron microscopy, electron probe microanalysis and x-ray diffraction (XRD. The crystal structure of the ternary compounds was studied by XRD and electron backscatter diffraction. Four ternary intermetallic (IM compounds were identified in this system: Ca3MgxZn15−x (4.6≤x≤12 at 335 °C, IM1, Ca14.5Mg15.8Zn69.7 (IM2, Ca2Mg5Zn13 (IM3 and Ca1.5Mg55.3Zn43.2 (IM4. Three binary compounds were found to have extended solid solubility into ternary systems: CaZn11, CaZn13 and Mg2Ca form substitutional solid solutions where Mg substitutes for Zn atoms in the first two compounds, and Zn substitutes for both Ca and Mg atoms in Mg2Ca. The isothermal section of the Ca–Mg–Zn phase diagram at 335 °C was constructed on the basis of the obtained experimental results. The morphologies of the diffusion couples in the Ca–Mg–Zn phase diagram at 335 °C were studied. Depending on the terminal compositions of the diffusion couples, the two-phase regions in the diffusion zone have either a tooth-like morphology or contain a matrix phase with isolated and/or dendritic precipitates.

Crystal structure and bonding characteristics of In-doped β-Zn4Sb3

International Nuclear Information System (INIS)

Tang, Dingguo; Zhao, Wenyu; Cheng, Sudan; Wei, Ping; Yu, Jian; Zhang, Qingjie

2012-01-01

The effects of indium impurity on the crystal structure and bonding characteristics of In-doped β-Zn 4 Sb 3 were investigated by powder X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The XRD Rietveld refinement indicates that the indium impurity preferentially substitutes one of Sb atoms in Sb–Sb dimer at the 12c Sb(2) site and simultaneously leads to the increase of Zn occupancy. The observations of binding energy shift and a new valence state in Sb 3d core-level XPS spectra can be attributed to the charge transfer from In and Zn to Sb. As a result, more electropositive Zn atoms are needed to maintain the charge balance. The reduction of the lattice thermal conductivity is ascribed to the formation of the asymmetric Sb–In bond, resulting in much low lattice thermal conductivity of 0.49 W −1 K −1 of Zn 4 Sb 2.96 In 0.04 . - Graphical abstract: The indium impurity substitutes one of Sb atoms in Sb–Sb dimer, resulting the charge transfer from In to Sb, which leads to the binding energy of Sb 3d core level XPS spectra shift to low value. Highlights: ► The indium impurity preferentially substitutes one of Sb atoms in Sb–Sb dimer at the 12c Sb(2) site. ► The occupancy of Zn increases by the In substitution for Sb, whereas that of Sb keeps constant. ► The binding energy of Sb 3d shifts to low value. ► The charge transfer occurs from In and Zn to Sb.

Synthesis, structural investigation and magnetic properties of Zn{sup 2+} substituted cobalt ferrite nanoparticles prepared by the sol–gel auto-combustion technique

Energy Technology Data Exchange (ETDEWEB)

Raut, A.V., E-mail: nano9993@gmail.com [Vivekanand Arts and Sardar Dalipsingh Commerce and Science College, Aurangabad, 431004 Maharastra (India); Barkule, R.S.; Shengule, D.R. [Vivekanand Arts and Sardar Dalipsingh Commerce and Science College, Aurangabad, 431004 Maharastra (India); Jadhav, K.M., E-mail: drjadhavkm@gmail.com [Department of Physics, Dr. Babasaheb Ambedkar Marathwada University, Aurangabad, 431004 Maharastra (India)

2014-05-01

Structural morphology and magnetic properties of the Co{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} (0.0≤x≥1.0) spinel ferrite system synthesized by the sol–gel auto-combustion technique using nitrates of respective metal ions have been studied. The ratio of metal nitrates to citric acid was taken at 1:3. The as prepared powder of cobalt zinc ferrite was sintered at 600 °C for 12 h after TG/DTA thermal studies. Compositional stoichiometry was confirmed by energy dispersive analysis of the X-ray (EDAX) technique. Single phase cubic spinel structure of Co–Zn nanoparticles was confirmed by XRD data. The average crystallite size (t), lattice constant (a) and other structural parameters of zinc substituted cobalt ferrite nanoparticles were calculated from XRD followed by SEM and FTIR. It is observed that the sol–gel auto-combustion technique has many advantages for the synthesis of technologically applicable Co–Zn ferrite nanoparticles. The present investigation clearly shows the effect of the synthesis method and possible relation between magnetic properties and microstructure of the prepared samples. Increase in nonmagnetic Zn{sup 2+} content in cobalt ferrite nanoparticles is followed by decrease in n{sub B}, M{sub s} and other magnetic parameters. Squareness ratio for the Co-ferrite was 1.096 at room temperature. - Highlights: • Co–Zn nanoparticles are prepared by sol–gel auto-combustion method. • Structural properties were characterized by XRD, SEM, and FTIR. • Compositional stoichiometry was confirmed by EDAX analysis. • Magnetic parameters were measured by the pulse field hysteresis loop technique.

Room-temperature multiferroic and magnetocapacitance effects in M-type hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19}

Energy Technology Data Exchange (ETDEWEB)

Tang, Rujun, E-mail: tangrj@suda.edu.cn, E-mail: yanghao@nuaa.edu.cn; Zhou, Hao; You, Wenlong [Jiangsu Key Laboratory of Thin Films, College of Physics, Optoelectronics and Energy, Soochow University, Suzhou 215006 (China); Yang, Hao, E-mail: tangrj@suda.edu.cn, E-mail: yanghao@nuaa.edu.cn [College of Science, Nanjing University of Aeronautics and Astronautics, Nanjing 211106 (China)

2016-08-22

The room-temperature multiferroic and magnetocapacitance (MC) effects of polycrystalline M-type hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} have been investigated. The results show that the magnetic moments of insulating BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} can be manipulated by the electric field at room temperature, indicating the existence of magnetoelectric coupling. Moreover, large MC effects are also observed around the room temperature. A frequency dependence analysis shows that the Maxwell-Wagner type magnetoresistance effect is the dominant mechanism for MC effects at low frequencies. Both the magnetoelectric-type and non-magnetoelectric-type spin-phonon couplings contribute to the MC effects at high frequencies with the former being the dominant mechanism. The above results show that the hexaferrite BaFe{sub 10.2}Sc{sub 1.8}O{sub 19} is a room-temperature multiferroic material that can be potentially used in magnetoelectric devices.

Sorption of phosphates and thiocyanates on isomorphic substituted Mg/Zn–Al-type hydrotalcites

Directory of Open Access Journals (Sweden)

RODICA PODE

2008-08-01

Full Text Available The sorption equilibriums of phosphate and thiocyanate anions on isomorphic substituted Mg/Zn–Al-type hydrotalcites were investigated in this study. Langmuir and Freundlich isotherms were used to interpret the equilibrium data for phosphate. The sorption equilibriums of phosphate on Mg3Al, Mg2ZnAl and Mg1.5Zn1.5Al hydrotalcites were well described by the Langmuir isotherm. The highest maximum sorption capacities for these adsorbents were as follows: 111, 101 and 95 mg g-1. The equilibrium constant and standard Gibbs energy changes were also calculated from the sorption data. Standard Gibbs energy changes of about –20 kJ mol-1 indicated that the process might be considered as physical adsorption. The sorption equilibriums of phosphate on isomorphic substituted samples of MgZn2Al and Zn3Al were well described by the Freundlich isotherm. Thiocyanate showed a relative low affinity for the studied materials, as indicated by both the “S”-shaped isotherms and low sorption capacities. The sorption of phosphate and thiocyanate on the investigated hydrotalcites showed a continuous decrease of the sorption capacity in the following order: Mg3Al > Mg2ZnAl > Mg1.5Zn1.5Al > MgZn2Al > Zn3Al.

Effect of neodymium substitutions on electromagnetic properties in low temperature sintered NiCuZn ferrite

Energy Technology Data Exchange (ETDEWEB)

Wu, C.P., E-mail: itria20161@itri.org.tw; Tung, M.J.; Ko, W.S.; Wang, Y.P.; Tong, S.Y.; Yang, M.D.

2015-11-01

Nd{sup 3+} ions substituted Ni{sub 0.37}Cu{sub 0.14}Zn{sub 0.52}Fe{sub 2}O{sub 4} (Nd{sup 3+} ions content=0, 0.01, 0.04, 0.6, 1.5 wt%) were prepared by the usual standard ceramic method at 1030 °C sintering temperature, and the composition dependence of the physical and magnetic properties has been investigated. SEM micrographs and EDX analysis revealed that it is no obvious impurities up to Nd{sup 3+} ions content wt%=0.04. For higher Nd{sup 3+} ions content samples (0.6 and 1.5 wt%), there are two kind of impurities Cu-rich and Nd-rich iron oxide phase. The saturation magnetization of the 0.01 wt% Nd{sup 3+}ions content sample is higher as result of that the A–B sites distance and YK-angles are shorter and smaller. The saturation magnetization of 0.04–1.5 wt% Nd{sup 3+} ion content sample are reduced, since the total magnetic moments of the AB site are decreased. For the 0.6 wt% sample, the Curie temperature increasing is as result of the Cu-rich iron oxide separating out. The maximum enhancements of permeability μ′ are improved to 11.2% (0.04 wt%) and 29.2% (0.6 wt%) at the 6.7 and 13.8 MHz, respectively. However, it is notice that small amount substitutions of Nd{sup 3+} increase the high frequency electromagnetic characteristics, can be applied to NFC technology and WPT technologies.

Electrophoretic deposition of zinc-substituted hydroxyapatite coatings.

Science.gov (United States)

Sun, Guangfei; Ma, Jun; Zhang, Shengmin

2014-06-01

Zinc-substituted hydroxyapatite nanoparticles synthesized by the co-precipitation method were used to coat stainless steel plates by electrophoretic deposition in n-butanol with triethanolamine as a dispersant. The effect of zinc concentration in the synthesis on the morphology and microstructure of coatings was investigated. It is found that the deposition current densities significantly increase with the increasing zinc concentration. The zinc-substituted hydroxyapatite coatings were analyzed by X-ray diffraction, scanning electron microscopy and Fourier transform infrared spectroscopy. It is inferred that hydroxyapatite and triethanolamine predominate in the chemical composition of coatings. With the increasing Zn/Ca ratios, the contents of triethanolamine decrease in the final products. The triethanolamine can be burnt out by heat treatment. The tests of adhesive strength have confirmed good adhesion between the coatings and substrates. The formation of new apatite layer on the coatings has been observed after 7days of immersion in a simulated body fluid. In summary, the results show that dense, uniform zinc-substituted hydroxyapatite coatings are obtained by electrophoretic deposition when the Zn/Ca ratio reaches 5%. Copyright © 2014 Elsevier B.V. All rights reserved.

Effect of substitution of 1 at% Ni for Zn on the microstructure and mechanical properties of Mg{sub 94}Y{sub 4}Zn{sub 2} alloy

Energy Technology Data Exchange (ETDEWEB)

Liu, Huan, E-mail: liuhuanseu@hotmail.com [Jiangsu Key Lab of Advanced Metallic Materials, School of Material Science and Engineering, Southeast University, Nanjing 211189 (China); Xue, Feng, E-mail: xuefeng@seu.edu.cn [Jiangsu Key Lab of Advanced Metallic Materials, School of Material Science and Engineering, Southeast University, Nanjing 211189 (China); Bai, Jing; Zhou, Jian [Jiangsu Key Lab of Advanced Metallic Materials, School of Material Science and Engineering, Southeast University, Nanjing 211189 (China); Liu, Xiaodao [Nanjing Yunhai Special Metals Co., Ltd., Nanjing 211200 (China)

2013-11-15

The microstructure and mechanical properties of Mg{sub 94}Y{sub 4}Zn{sub 2} and Mg{sub 94}Y{sub 4}Zn{sub 1}Ni{sub 1} alloys have been systematically investigated by optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and an electronic universal testing machine. The as-cast WZ42 alloy is composed of α-Mg matrix, 18R LPSO (long period stacking ordered) phase and a small fraction of Mg{sub 24}(Y,Zn){sub 5} phases. With the replacement of 1 at% Ni atoms, the phase structures in WZN411 alloy remain unchanged, but their chemical compositions vary obviously. A great number of stacking faults exist in α-Mg grains of WZ42 alloy, while they are barely observed in WZN411 alloy. After annealing at 500 °C for 12 h, there are plenty of 14H LPSO lamellas formed in WZ42 alloy and many nano-scale α-Mg slices generated between 18R phases. In contrast, the 18R in WZN411 alloy is thermally stable, and both the formation of α-Mg slices and 14H lamellas are restricted for annealed WZN411 alloy. Tensile tests indicate that the as-extruded WZ42 alloy exhibits ultimate tensile strength of 390 MPa, tensile yield strength of 246 MPa and elongation of 2.8% at room temperature. With the replacement of 1 at% Ni, the UTS and TYS of WZN411 alloy increase by 20 MPa and the ductility improves as well. The improvement of comprehensive mechanical properties could be ascribed to the substitution of 1 at% Ni element, which could enhance the degree of solid-solution strengthening and stimulate the thermal stability of 18R phase during annealing and extrusion processes.

Lattice dynamics and vibration modes frequencies for substitutional impurities in InP, GaP and ZnS

International Nuclear Information System (INIS)

Vandevyver, Michel; Plumelle, Pierre.

1977-01-01

The model used is a rigid-ion model with an effective ionic charge including general interactions for nearest and next nearest neighbours and long range Coulomb interactions. It provides a good fit with available neutron data and with infrared absorption results for InP. In this model, no hypothesis is made a priori on the interatomic forces and the eleven parameters given by the model are used. A mathematical model which employs a Green's function technique in the mass defect and the nearest neighbour force constant defect approximation is used to calculate the lattice dynamics of the imperfect crystal. The frequencies of the local modes, the gap modes and the band modes, are given for isolated substitutional impurities. The same calculation is achieved for GaP and ZnS and the results are compared with infrared data [fr

Electronic structure of Al- and Ga-doped ZnO films studied by hard X-ray photoelectron spectroscopy

Directory of Open Access Journals (Sweden)

M. Gabás

2014-01-01

Full Text Available Al- and Ga-doped sputtered ZnO films (AZO, GZO are semiconducting and metallic, respectively, despite the same electronic valence structure of the dopants. Using hard X-ray photoelectron spectroscopy we observe that both dopants induce a band in the electronic structure near the Fermi level, accompanied by a narrowing of the Zn 3d/O 2p gap in the valence band and, in the case of GZO, a substantial shift in the Zn 3d. Ga occupies substitutional sites, whereas Al dopants are in both substitutional and interstitial sites. The latter could induce O and Zn defects, which act as acceptors explaining the semiconducting character of AZO and the lack of variation in the optical gap. By contrast, mainly substitutional doping is consistent with the metallic-like behavior of GZO.

Low-energy excitations in impurity substituted CuGeO3

International Nuclear Information System (INIS)

Jones, B. R.; Sushkov, A. B.; Musfeldt, J. L.; Wang, Y. J.; Revcolevschi, A.; Dhalenne, G.

2001-01-01

We report far-infrared reflectance measurements of Zn- and Si-doped CuGeO 3 single crystals as a function of applied magnetic field at low temperature. Overall, the low-energy far-infrared spectra are extraordinarily sensitive to the various phase boundaries in the H-T diagram, with the features being especially rich in the low-temperature dimerized state. Zn impurity substitution rapidly collapses the 44 cm -1 zone-boundary spin Peierls gap, although broadened magnetic excitations are observed at the lightest doping level (0.2%) and a remnant is still observable at 0.7% substitution. In a 0.7% Si-doped sample, there is no evidence of the spin gap. Impurity substitution effects on the intensity of the 98 cm -1 zone-folding mode are striking as well. The lightly doped Zn crystals display an enhanced response, and even at intermediate doping levels, the mode intensity is larger than that in the pristine material. The Si-doped sample also displays an increased intensity of the 98 cm -1 mode in the spin Peierls phase relative to the pure material. The observed trends are discussed in terms of the effect of disorder on the spin gap and 98 cm -1 mode, local oscillator strength sum rules, and broken selection rules

Evaluation of structural, morphological and magnetic properties of CuZnNi (Cu{sub x}Zn{sub 0.5−x}Ni{sub 0.5}Fe{sub 2}O{sub 4}) nanocrystalline ferrites for core, switching and MLCI’s applications

Energy Technology Data Exchange (ETDEWEB)

Akhtar, Majid Niaz, E-mail: majidniazakhtar@ciitlahore.edu.pk [Department of Physics, COMSATS Institute of Information Technology, Lahore, 54000 Pakistan (Pakistan); Khan, Muhammad Azhar [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur, 63100 Pakistan (Pakistan); Ahmad, Mukhtar [Department of Physics, COMSATS Institute of Information Technology, Lahore, 54000 Pakistan (Pakistan); Nazir, M.S. [Department of Chemical Engineering, COMSATS Institute of Information Technology, Lahore, 54000 Pakistan (Pakistan); Imran, M.; Ali, A.; Sattar, A. [Department of Physics, COMSATS Institute of Information Technology, Lahore, 54000 Pakistan (Pakistan); Murtaza, G. [Centre for Advanced Studies in Physics, G.C. University, Lahore (Pakistan)

2017-01-01

The influence of Cu substitution on the structural and morphological characteristics of Ni–Zn nanocrystalline ferrites have been discussed in this work. The detailed and systematic magnetic characterizations were also done for Cu substituted Ni–Zn nanoferrites. The nanocrystalline ferrites of Cu substituted Cu{sub x}Zn{sub 0.5−x}Ni{sub 0.5}Fe{sub 2}O{sub 4} ferrites (x=0, 0.1, 0.2, 0.3, 0.4 and 0.5) were synthesized using sol gel self-combustion hybrid method. X-ray diffraction (XRD), Field emission scanning electron microscopy (FESEM), Transmission electron microscope (TEM) and Vibrating sample magnetometer (VSM) were used to investigate the properties of Cu substituted nanocrystalline ferrites. Single phase structure of Cu substituted in Ni–Zn nanocrystalline ferrites were investigated for all the samples. Crystallite size, lattice constant and volume of the cell were found to increase by increasing Cu contents in spinel structure. The better morphology with well-organized nanocrystals of Cu–Zn–Ni ferrites at x=0 and 0.5 were observed from both FESEM and TEM analysis. The average grain size was 35–46 nm for all prepared nanocrystalline samples. Magnetic properties such as coercivity, saturation, remanence, magnetic squareness, magneto crystalline anisotropy constant (K) and Bohr magneton were measured from the recorded M–H loops. The magnetic saturation and remanence were increased by the incorporation of Cu contents. However, coercivity follow the Stoner-Wolforth model except for x=0.3 which may be due to the site occupancy and replacement of Cu contents from octahedral site. The squareness ratio confirmed the super paramgnetic behaviour of the Cu substituted in Ni–Zn nanocrystalline ferrites. Furthermore, Cu substituted Ni–Zn nanocrystalline ferrites may be suitable for many industrial and domestic applications such as components of transformers, core, switching, and MLCI’s due to variety of the soft magnetic characteristics. - Highlights

Thermogravimetric and magneticproperties of Ni1-X Zn xFe2O4 nanoparticles synthesized by coprecipitation

Directory of Open Access Journals (Sweden)

Kandasamy Velmurugan

2009-01-01

Full Text Available Ni1-xZn xFe2O4 (x = 0 to 1 nanoparticles of size less than 9 nm were prepared by a chemical coprecipitation method which could be used for ferrofluid preparation. XRD, VSM and DTA-TG (STA were used to study the effect of variation in Zn substitution and its influence on particle size, magnetic properties such as M S, H C and Curie temperature, as well as on the water content. ICP was used to estimate Ni, Zn and Fe concentrations. The average crystallite size (DaveXR of the particles was found to decrease from 8.95 to 6.92 nm with increasing zinc substitution. The lattice constant (a o increased with increasing zinc substitution. The specific saturation magnetization (M S of the particles was measured at room temperature. Magnetic parameters such as M S, Hc, and Mr were found to decrease with increasing zinc substitution. Estimation of the water content, which varies the Zn concentration, plays a vital role for the correct determination of cation contents. The Curie temperature was found to decrease with increasing zinc substitution.

Spectroscopic investigation of an intrinsic room temperature ferromagnetism in Co doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

N, Srinatha [Department of Physics, JB Campus, Bangalore University, Bangalore 560056 (India); Angadi, Basavaraj, E-mail: brangadi@gmail.com [Department of Physics, JB Campus, Bangalore University, Bangalore 560056 (India); Nair, K.G.M. [UGC-DAE-CSR, Kalpakkam Node, Kalpakkam, Kokilamedu 603 102 (India); Deshpande, Nishad G.; Shao, Y.C.; Pong, Way-Faung [Department of Physics, Tamkang University, Tamsui, Taipei 251, Taiwan (China)

2014-08-15

Highlights: • For the first time L-Valine was used as a fuel to synthesize Co:ZnO nanoparticles by solution combustion method. • Single phase and ferromagnetic nature were confirmed through XRD, SQUID, NEXAFS and XMCD. • Through NEXAFS and XMCD, the effect of ‘Co’ substitution at O K-edge, Co L{sub 3,2} edge, Zn L{sub 3,2} edge have been investigated. • Spectral features of NEXAFS and XMCD confirms an intrinsic RTFM by substitution of ‘Co{sup 2+}’ at ‘Zn{sup 2+}’ site and rules out the presence of secondary phases. - Abstract: Pure and Co substituted ZnO nano crystalline particles were prepared by solution combustion technique using L-Valine as a fuel. As synthesized powder samples were characterized by X-ray diffractometer and SQUID magnetometer to confirm the formation of single phase wurtzite structure and to study the bulk magnetic response of the sample, respectively. Magnetic studies show that Co doped ZnO nanoparticles exhibit ferromagnetism (FM) at room temperature (RT). Furthermore, the electronic structure and element specific magnetic properties were investigated by near-edge X-ray absorption fine structure (NEXAFS) and X-ray magnetic circular dichroism (XMCD) measurements, respectively. The effect of Co substitution on the spectral features of Co–ZnO at O K-edge, Co L{sub 3,2} edge, Zn L{sub 3,2} edge have been investigated. The spectral features of NEXAFS at Co L{sub 3,2} edge is entirely different from the spectral features of metallic clusters and other impurity phases, which rules out the presence of impurity phases. The valence state of ‘Co’ ion is found to be in +2 state. The FM nature of the sample was confirmed through XMCD spectra, which is due to the incorporation of divalent ‘Co’ ions. Hence the presented results confirm the substitution of ‘Co’ ions at ‘Zn’ site in the host lattice, which is responsible for the RTFM.

Synthesis and characterization of polyaniline-hexaferrite composites

Energy Technology Data Exchange (ETDEWEB)

Khursheed, Tooba [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Islam, M.U., E-mail: dr.misbahulislam@bzu.edu.pk [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Asif Iqbal, M. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); College of E & ME, National University of Science and Technology, Islamabad (Pakistan); Ali, Irshad, E-mail: irshadalibzu@gmail.com [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Shakoor, Abdul [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Awan, M.S. [Center for Micro and Nano Devices Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan); Iftikhar, Aisha [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Azhar Khan, Muhammad [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Naeem Ashiq, Muhammad [Institute of Chemical Science, Bahauddin Zakariya University, Multan 60800 (Pakistan)

2015-11-01

Polyaniline was synthesized by chemical polymerization using aniline as monomer, and Y-type hexaferrite with composition (Co{sub 2}Mn{sub 2}Sr{sub 1.66}Nd{sub 0.4}Fe{sub 10}O{sub 22}) was prepared by co-precipitation assisted by surfactant. Three composites of Polyaniline with different ferrite ratios were prepared by mechanical blending. The synthesized samples were characterized by X-Ray diffraction, Scanning electron microscopy and electrical measurements. The XRD analysis reveals that no second phase was observed in Y-type hexagonal ferrite. In PANI-Ferrite composites, significant changes in resistivity, real and imaginary part of complex permittivity were observed with the increase of ferrite in the polyaniline matrix. At low frequencies the magnitude of dielectric constant and complex permittivity is high with few relaxation peaks. AC conductivity of PANI-Ferrite composites increase with the increase of frequency following Jonscher law. The resistivity and activation energy were found to show similar behavior. - Highlights: • Co{sub 2}Mn{sub 2}Sr{sub 1.66}Nd{sub 0.4}Fe{sub 10}O{sub 22} was prepared by co-precipitation. • Polyaniline was synthesized by chemical polymerization. • AC conductivity increase with the increase of frequency. • The resistivity and activation energy were found to show similar behavior.

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

Science.gov (United States)

Rashad, M. M.; Rayan, D. A.; El-Barawy, K.

2010-01-01

Nanocrystallite Mn doped Zn1-XS (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn2+ ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200oC for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn2+ ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn2+ ions up to 0.2.

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

International Nuclear Information System (INIS)

Rashad, M M; Rayan, D A; El-Barawy, K

2010-01-01

Nanocrystallite Mn doped Zn 1-X S (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn 2+ ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200 o C for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn 2+ ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn 2+ ions up to 0.2.

Improved Optical and Morphological Properties of Vinyl-Substituted Hybrid Silica Materials Incorporating a Zn-Metalloporphyrin

Directory of Open Access Journals (Sweden)

Zoltán Dudás

2018-04-01

Full Text Available This work is focused on a novel class of hybrid materials exhibiting enhanced optical properties and high surface areas that combine the morphology offered by the vinyl substituted silica host, and the excellent absorption and emission properties of 5,10,15,20-tetrakis(N-methyl-4-pyridylporphyrin-Zn(II tetrachloride as a water soluble guest molecule. In order to optimize the synthesis procedure and the performance of the immobilized porphyrin, silica precursor mixtures of different compositions were used. To achieve the requirements regarding the hydrophobicity and the porous structure of the gels for the successful incorporation of porphyrin, the content of vinyltriacetoxysilane was systematically changed and thoroughly investigated. Substitution of the silica gels with organic groups is a viable way to provide new properties to the support. An exhaustive characterization of the synthesized silica samples was realised by complementary physicochemical methods, such as infrared spectroscopy (FT-IR, absorption spectroscopy (UV-Vis and photoluminescence, nuclear magnetic resonance spectroscopy (29Si-MAS-NMR transmission and scanning electron microscopy (TEM and SEM, nitrogen absorption (BET, contact angle (CA, small angle X ray and neutron scattering (SAXS and SANS. All hybrids showed an increase in emission intensity in the wide region from 575 to 725 nm (Q bands in comparison with bare porphyrin. By simply tuning the vinyltriacetoxysilane content, the hydrophilic/hydrophobic profile of the hybrid materials was changed, while maintaining a high surface area. Good control of hydrophobicity is important to enhance properties such as dispersion, stability behaviour, and resistance to water, in order to achieve highly dispersible systems in water for biomedical applications.

Effect of doping and annealing on the physical properties of ZnO:Mg ...

Indian Academy of Sciences (India)

nescence (PL), scanning electron microscopy (SEM) and transmission ... nanoparticles show unique, size-dependent optical properties due to the ..... Mg substitute into ZnO lattice at Zn sites, instead of forming impurity compound or mag-.

Nanofiber production of poly (vinylidene fluoride) / hexaferrite, obtained by Blow Spinning Technique; Producao de nanofibras de poli (fluoreto de vinilideno)/hexaferrita, obtidos pela tecnica Blow Spinning

Energy Technology Data Exchange (ETDEWEB)

Dias, G.C.; Zadorosny, L.; Malmonge, J.A.; Malmonge, L.F., E-mail: gabriel.fct@gmail.com [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Ilha Solteira, SP (Brazil)

2014-07-01

In this study, fibrous films of poly (vinylidene fluoride) - PVDF with barium hexaferrite particles were obtained by Solution Blow Spinning technique. In such technique, the polymer solution is injected through an inner nozzle which experiences the action of an accelerated flux of gas that drags and stretches the jet solution forming the nanofibers. The films were obtained from solutions of PVDF/DMF (30% w/v), which was incorporated into barium hexaferrite particles in proportions of 1, 3 and 5% (w / w). The results of the micrographs revealed the formation of a fibrous film with good dispersion of the particles. Xray analyzes showed the predominance of the β crystalline phase of PVDF. The increase of the amount of particles induces the appearance of a characteristic peak of PVDF. EDX measurements confirmed the presence of particles in the films. (author)

Single and couple doping ZnO nanocrystals characterized by positron techniques

Science.gov (United States)

Pasang, Tenzin; Namratha, Keerthiraj; Guagliardo, Paul; Byrappa, Kullaiah; Ranganathaiah, Chikkakuntappa; Samarin, S.; Williams, J. F.

2015-04-01

Zinc oxide (ZnO) nanocrystals have been synthesized using a mild hydrothermal process using low temperatures and pressures with the advantages of free growth catalyst, low cost and alternative technology. Positron annihilation lifetime spectroscopy and coincidence Doppler broadening (CDB) spectroscopic methods have been used to investigate the roles of single- and co-dopants and native defects of the ZnO nanocrystals controlled by the synthesis process. It is shown that single Ag1+ and Pd2+ dopants occupy interstitial sites of the ZnO lattice and single Ru3+ doping replaces Zn vacancies substitutionally with a significant effect on the CDB momentum ratio curves when compared using ZnO as the reference spectrum. The co-doping of the ZnO lattice with (Sn4+ + Co2+) shows similar CDB ratios as Ru3+ single-doping. Also co-doping with (Ag1+ + Pd2+) or (Ag1+ + W6+) shows significant decreases in the band gap energy up to about 12.6% compared to single doping. The momentum ratio curves, referenced to undoped ZnO, indicate dopants in interstitial and substitutional sites. The presence of transition metal ions interstitially will trap electrons which resist the recombination of electrons and in turn affect the conductivity of the material.

Single and couple doping ZnO nanocrystals characterized by positron techniques

International Nuclear Information System (INIS)

Pasang, Tenzin; Namratha, Keerthiraj; Byrappa, Kullaiah; Guagliardo, Paul; Ranganathaiah, Chikkakuntappa; Samarin, S; Williams, J F

2015-01-01

Zinc oxide (ZnO) nanocrystals have been synthesized using a mild hydrothermal process using low temperatures and pressures with the advantages of free growth catalyst, low cost and alternative technology. Positron annihilation lifetime spectroscopy and coincidence Doppler broadening (CDB) spectroscopic methods have been used to investigate the roles of single- and co-dopants and native defects of the ZnO nanocrystals controlled by the synthesis process. It is shown that single Ag 1+ and Pd 2+ dopants occupy interstitial sites of the ZnO lattice and single Ru 3+ doping replaces Zn vacancies substitutionally with a significant effect on the CDB momentum ratio curves when compared using ZnO as the reference spectrum. The co-doping of the ZnO lattice with (Sn 4+ + Co 2+ ) shows similar CDB ratios as Ru 3+ single-doping. Also co-doping with (Ag 1+ + Pd 2+ ) or (Ag 1+ + W 6+ ) shows significant decreases in the band gap energy up to about 12.6% compared to single doping. The momentum ratio curves, referenced to undoped ZnO, indicate dopants in interstitial and substitutional sites. The presence of transition metal ions interstitially will trap electrons which resist the recombination of electrons and in turn affect the conductivity of the material. (paper)

Structural, dielectric and gas sensing behavior of Mn substituted spinel MFe{sub 2}O{sub 4} (M=Zn, Cu, Ni, and Co) ferrite nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ranjith Kumar, E., E-mail: ranjueaswar@gmail.com [Department of Physics, Dr. NGP Institute of Technology, Coimbatore 641048, Tamil Nadu (India); Siva Prasada Reddy, P.; Sarala Devi, G. [Inorganic and Physical Chemistry Division, Indian Institute Chemical Technology, Hyderabad 500607 (India); Sathiyaraj, S. [Department of Chemistry, Dr. NGP Institute of Technology, Coimbatore 641048, Tamil Nadu (India)

2016-01-15

Spinel ferrite (MnZnFe{sub 2}O{sub 4}, MnCuFe{sub 2}O{sub 4}, MnNiFe{sub 2}O{sub 4} and MnCoFe{sub 2}O{sub 4}) nanoparticles have been prepared by evaporation method. The annealing temperature plays an important role on changing particle size of the spinel ferrite nanoparticles was found out by X-ray diffraction and transmission electron microscopy. The role of manganese substitution in the spinel ferrite nanoparticles were also analyzed for different annealing temperature. The substitution of Mn also creates a vital change in dielectric properties have been measured in the frequency range of 100 kHz to 5 MHz. These spinel ferrites are decomposed to α-Fe{sub 2}O{sub 3} after annealing above 550 °C in air. Through the characterization of the prepared powder, the effect of annealing temperature, chemical composition and preparation technique on the microstructure, particle size and dielectric properties of the Mn substituted spinel ferrite nanoparticles are discussed. Furthermore, Conductance response of Mn substituted MFe{sub 2}O{sub 4} ferrite nanoparticles were measured by exposing the materials to reducing gas like liquefied petroleum gas (LPG). - Highlights: • The egg white support to achieve sample with shorter reaction time. • Manganese plays a significant role in sensor response. • Nature of the ferrites was affected with increasing annealing temperature.

Magneto-optical effects of reflection on monocrystals of ferrite garnets, orthoferrites hexaferrites and hematite. [Yttrium oxides iron oxides; europium oxides; bismuth oxides

Energy Technology Data Exchange (ETDEWEB)

Krinchik, G S; Krylova, V A; Khrebtov, A P; Chepurova, E E

1975-01-01

The results of experimental studies of the equatorial Kerr effect in visible and ultraviolet ranges of the spectrum are given for ferromagnetic dielectrics of different classes: ferrimagnetic ferrite garnets and hexaferrites, as well as weakly ferromagnetic orthoferrites and hematite. A method for the nondestructive magneto-optical data readout using reflected light is proposed and described.

Core–shell interaction and its impact on the optical absorption of pure and doped core-shell CdSe/ZnSe nanoclusters

Energy Technology Data Exchange (ETDEWEB)

Wang, Xinqin; Cui, Yingqi; Zeng, Qun; Yang, Mingli, E-mail: myang@scu.edu.cn [Institute of Atomic and Molecular Physics, Key Laboratory of High Energy Density Physics and Technology of Ministry of Education, Sichuan University, Chengdu 610065 (China); Yu, Shengping [College of Chemistry and Environment Protection Engineering, Southwest University for Nationalities, Chengdu 610041 (China)

2016-04-07

The structural, electronic, and optical properties of core-shell nanoclusters, (CdSe){sub x}@(CdSe){sub y} and their Zn-substituted complexes of x = 2–4 and y = 16–28, were studied with density functional theory calculations. The substitution was applied in the cores, the shells, and/or the whole clusters. All these clusters are characterized by their core-shell structures in which the core-shell interaction was found different from those in core or in shell, as reflected by their bondlengths, volumes, and binding energies. Moreover, the core and shell combine together to compose a new cluster with electronic and optical properties different from those of separated individuals, as reflected by their HOMO-LUMO gaps and optical absorptions. With the substitution of Cd by Zn, the structural, electronic, and optical properties of clusters change regularly. The binding energy increases with Zn content, attributed to the strong Zn–Se bonding. For the same core/shell, the structure with a CdSe shell/core has a narrower gap than that with a ZnSe shell/core. The optical absorption spectra also change accordingly with Zn substitution. The peaks blueshift with increasing Zn concentration, accompanying with shape variations in case large number of Cd atoms are substituted. Our calculations reveal the core-shell interaction and its influence on the electronic and optical properties of the core-shell clusters, suggesting a composition–structure–property relationship for the design of core-shell CdSe and ZnSe nanoclusters.

Modulation of electromagnetic and absorption properties in 18-26.5 GHz frequency range of strontium hexaferrites with doping of cobalt-zirconium

Science.gov (United States)

Pubby, Kunal; Narang, Sukhleen Bindra; Kaur, Prabhjyot; Chawla, S. K.

2017-05-01

Hexaferrite nano-particles of stoichiometric composition {{Sr}}{({{CoZr}})_x}{{F}}{{{e}}_{12 - 2x}}{{{O}}_{19}}, with x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0 were prepared using sol-gel auto-combustion route owing to its advantages such as low sintering temperature requirement, homogeneity and uniformity of grains. Tartaric acid as a fuel was utilized to complete the chemical reaction. The goal of this study is to analyse the effect of co-substitution of cobalt and zirconium on the electromagnetic and absorption properties of pure {{SrF}}{{{e}}_{12}}{{{O}}_{19}} hexaferrite. The properties were measured on the rectangular pellets of thickness 2.5 mm for K-frequency band using Vector Network Analyzer. The doping of Co-Zr has resulted in increase in real as well as imaginary parts of permittivity. The values of real permittivity lie in the range 3.6-7.0 for all the composition. The real part of permeability remains in range 0.7-1.6 in the studied frequency band for all the samples and shows slightly increasing trend with frequency. The maximum values of dielectric loss tangent peak (3.04) and magnetic loss tangent peak (2.34), among all the prepared compositions, have been observed for composition x = 0.2. Compositions with x = 0.6 and x = 0.0 also have high dielectric and magnetic loss peaks. Dielectric loss peaks are attributed to dielectric resonance and magnetic loss peaks are attributed to natural resonance. Experimentally determined reflection loss results show that all six compositions of prepared series have high values of absorption to propose them as single-layer absorbers in 18-26.5 GHz frequency range. The composition with x = 0.2 has maximum absorption capacity with reflection loss peak of -37.2 dB at 24.3 GHz frequency. The undoped composition also has high absorption peak (-25.46 dB), but -10 dB absorption bandwidth is minimum (2.2 GHz) out of the present series. Maximum absorption bandwidth is obtained for x = 1.0 (4.1 GHz). Other doped compositions also

Modulation of electromagnetic and absorption properties in 18-26.5 GHz frequency range of strontium hexaferrites with doping of cobalt-zirconium

Energy Technology Data Exchange (ETDEWEB)

Pubby, Kunal; Narang, Sukhleen Bindra [Guru Nanak Dev University, Department of Electronics Technology, Amritsar (India); Kaur, Prabhjyot; Chawla, S.K. [Guru Nanak Dev University, Department of Chemistry, Centre for Advanced Studies-I, Amritsar (India)

2017-05-15

Hexaferrite nano-particles of stoichiometric composition Sr(CoZr){sub x}Fe{sub 12-2x}O{sub 19}, with x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0 were prepared using sol-gel auto-combustion route owing to its advantages such as low sintering temperature requirement, homogeneity and uniformity of grains. Tartaric acid as a fuel was utilized to complete the chemical reaction. The goal of this study is to analyse the effect of co-substitution of cobalt and zirconium on the electromagnetic and absorption properties of pure SrFe{sub 12}O{sub 19} hexaferrite. The properties were measured on the rectangular pellets of thickness 2.5 mm for K-frequency band using Vector Network Analyzer. The doping of Co-Zr has resulted in increase in real as well as imaginary parts of permittivity. The values of real permittivity lie in the range 3.6-7.0 for all the composition. The real part of permeability remains in range 0.7-1.6 in the studied frequency band for all the samples and shows slightly increasing trend with frequency. The maximum values of dielectric loss tangent peak (3.04) and magnetic loss tangent peak (2.34), among all the prepared compositions, have been observed for composition x = 0.2. Compositions with x = 0.6 and x = 0.0 also have high dielectric and magnetic loss peaks. Dielectric loss peaks are attributed to dielectric resonance and magnetic loss peaks are attributed to natural resonance. Experimentally determined reflection loss results show that all six compositions of prepared series have high values of absorption to propose them as single-layer absorbers in 18-26.5 GHz frequency range. The composition with x = 0.2 has maximum absorption capacity with reflection loss peak of -37.2 dB at 24.3 GHz frequency. The undoped composition also has high absorption peak (-25.46 dB), but -10 dB absorption bandwidth is minimum (2.2 GHz) out of the present series. Maximum absorption bandwidth is obtained for x = 1.0 (4.1 GHz). Other doped compositions also have high absorption bandwidth

Epitaxial growth of 100-μm thick M-type hexaferrite crystals on wide bandgap semiconductor GaN/Al{sub 2}O{sub 3} substrates

Energy Technology Data Exchange (ETDEWEB)

Hu, Bolin; Su, Zhijuan; Bennett, Steve; Chen, Yajie, E-mail: y.chen@neu.edu; Harris, Vincent G. [Center for Microwave Magnetic Materials and Integrated Circuits and Department of Electrical and Computer Engineering, Northeastern University, Boston, Massachusetts 02115 (United States)

2014-05-07

Thick barium hexaferrite BaFe{sub 12}O{sub 19} (BaM) films having thicknesses of ∼100 μm were epitaxially grown on GaN/Al{sub 2}O{sub 3} substrates from a molten-salt solution by vaporizing the solvent. X-ray diffraction measurement verified the growth of BaM (001) textured growth of thick films. Saturation magnetization, 4πM{sub s}, was measured for as-grown films to be 4.6 ± 0.2 kG and ferromagnetic resonance measurements revealed a microwave linewidth of ∼100 Oe at X-band. Scanning electron microscopy indicated clear hexagonal crystals distributed on the semiconductor substrate. These results demonstrate feasibility of growing M-type hexaferrite crystal films on wide bandgap semiconductor substrates by using a simple powder melting method. It also presents a potential pathway for the integration of ferrite microwave passive devices with active semiconductor circuit elements creating system-on-a-wafer architectures.

Hydrothermal synthesis and magnetic properties of Mn doped ZnS nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Rashad, M M; Rayan, D A; El-Barawy, K [Central Metallurgical Research and Development Institute PO Box: 87 Helwan, Cairo (Egypt)

2010-01-01

Nanocrystallite Mn doped Zn{sub 1-X}S (X = 0 to 0.4) powders have been synthesized through a hydrothermal route. The effect of the hydrothermal temperature and Mn{sup 2+} ions substitution on the crystal structure, crystallite size, microstructure and magnetic properties were investigated using (XRD), (SEM) and (VSM). The results revealed that wurtzite zinc sulfide phase was formed using thiourea as a sulfur source at temperature 150- 200{sup o}C for 24 h. The crystallite size was (7.9-15.1 nm) was obtained at the same conditions. The doping of Mn{sup 2+} ions decreased the crystallite size of the formed ZnS wurtzite phase was in the range between 7.9 and 3.8 nm. SEM micrographs showed that the produced ZnS and Mn doped ZnS particles were appeared as spherical shape. The magnetic properties were improved by substitution of Mn{sup 2+} ions up to 0.2.

Growth of Ba-hexaferrite films on single crystal 6-H SiC

International Nuclear Information System (INIS)

Chen Zhoahui; Yang, Aria; Yoon, S.D.; Ziemer, Katherine; Vittoria, Carmine; Harris, V.G.

2006-01-01

Barium hexaferrite films have been processed by pulsed laser deposition on single crystal 6-H silicon carbide substrates. Atomic force microscopy images show hexagonal crystals (∼0.5μm in diameter) oriented with the c-axis perpendicular to the film plane. X-ray θ-2θ diffraction measurements indicate a strong (0,0,2n) alignment of crystallites. The magnetization for low-pressure deposition (20mTorr) is comparable to bulk values (4πM s ∼4320G). The loop squareness, important for self-bias microwave device applications, increases with oxygen pressure reaching a maximum value of 70%. This marks the first growth of a microwave ferrite on SiC substrates and offers a new approach in the design and development of μ-wave and mm-wave monolithic integrated circuits. c integrated circuits

Mn{sup 2+} ions distribution in doped sol–gel deposited ZnO films

Energy Technology Data Exchange (ETDEWEB)

Stefan, Mariana, E-mail: mstefan@infim.ro [National Institute of Materials Physics, P.O. Box MG-7, 077125 Magurele (Romania); Ghica, Daniela; Nistor, Sergiu V.; Maraloiu, Adrian V. [National Institute of Materials Physics, P.O. Box MG-7, 077125 Magurele (Romania); Plugaru, Rodica [National Institute for R & D in Microtechnologies (IMT), Erou Iancu Nicolae Str. 126A, 077190 Bucharest (Romania)

2017-02-28

Highlights: • Several Mn{sup 2+} centers observed by EPR in sol–gel ZnO films. • Mn{sup 2+} ions localized at Zn{sup 2+} sites in ZnO grains and disordered ZnO phase. • Sixfold coordinated Mn{sup 2+} ions localized in inter-grain region. • Aggregated Mn in insular-like regions between ZnO grains in the ZnO:5%Mn film. • Aggregated Mn phase presence and distribution observed by EPR and EDX-STEM. - Abstract: The localization and distribution of the Mn{sup 2+} ions in two sol–gel deposited ZnO films doped with different manganese concentrations were investigated by electron paramagnetic resonance spectroscopy and analytical transmission electron microscopy. In the lightly doped sample the Mn{sup 2+} ions are mainly localized substitutionally at isolated tetrahedrally coordinated Zn{sup 2+} sites in both crystalline ZnO nanograins (34%) and surrounding disordered ZnO (52%). In the highly doped ZnO film, a much smaller proportion of manganese substitutes Zn{sup 2+} in the crystalline and disordered ZnO (10%). The main amount (85%) of manganese aggregates in a secondary phase as an insular-like distribution between the ZnO nanograins. The remaining Mn{sup 2+} ions (14% and 5% at low and high doping levels, respectively) are localized at isolated, six-fold coordinated sites, very likely in the disordered intergrain region. Annealing at 600 °C induced changes in the Mn{sup 2+} ions distribution, reflecting the increase of the ZnO crystallization degree, better observed in the lightly doped sample.

Three series of quaternary rare-earth transition-metal pnictides with CaAl{sub 2}Si{sub 2}-type structures: RECuZnAs{sub 2}, REAgZnP{sub 2}, and REAgZnAs{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Stoyko, Stanislav S.; Ramachandran, Krishna K.; Blanchard, Peter E.R. [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Rosmus, Kimberly A.; Aitken, Jennifer A. [Department of Chemistry and Biochemistry, Duquesne University, Pittsburgh, PA 15282 (United States); Mar, Arthur, E-mail: arthur.mar@ualberta.ca [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada)

2014-05-01

Three series of quaternary rare-earth transition-metal pnictides REMM′Pn{sub 2} (M=Cu, Ag; M′=Zn; Pn=P, As) have been prepared by reaction of the elements at 800 °C, with crystal growth promoted through the addition of iodine. The extent of RE substitution is broad in these series: RECuZnAs{sub 2} (RE=Y, La-Nd, Sm, Gd–Lu), REAgZnP{sub 2} (RE=La–Nd, Sm, Gd–Dy), and REAgZnAs{sub 2} (RE=La-Nd, Sm, Gd-Dy). Powder and single-crystal X-ray diffraction analysis revealed that they adopt the trigonal CaAl{sub 2}Si{sub 2}-type structure (space group P3{sup ¯}m1, Z=1), in which Cu or Ag atoms are disordered with Zn atoms over the unique tetrahedrally coordinated transition-metal site. Magnetic measurements indicated Curie–Weiss behavior for several members of the RECuZnAs{sub 2} and REAgZnP{sub 2} series. Core-line X-ray photoelectron spectra (XPS) collected on some RECuZnAs{sub 2} members corroborate the charge assignment deduced by the Zintl concept for these compounds, (RE{sup 3+})(M{sup 1+})(Zn{sup 2+})(Pn{sup 3−}){sub 2}. Optical diffuse reflectance spectra and valence band XPS spectra established that these compounds are small band-gap semiconductors (up to ∼0.8 eV in REAgZnP{sub 2}) or semimetals (RECuZnAs{sub 2}). Band structure calculations also support this electronic structure and indicate that the band gap can be narrowed through appropriate chemical substitution (RE=smaller atoms, M=Cu, and Pn=As). - Graphical abstract: Cu or Ag atoms are disordered with Zn atoms over the tetrahedral site within relatively rigid [M{sub 2}Pn{sub 2}] slabs in three series of quaternary pnictides adopting the CaAl{sub 2}Si{sub 2}-type structure. - Highlights: • Three series (comprising 25 compounds) of pnictides REMM'Pn{sub 2} were prepared. • Cu or Ag atoms are disordered with Zn atoms within relatively rigid [M{sub 2}Pn{sub 2}] slabs. • They are semimetals or small band-gap semiconductors. • RECuZnAs{sub 2} and REAgZnP{sub 2} are generally

The Semi-Quantitative Study of Magnetization Process on Milling and Reannealing of Barium Hexaferrite (BaO.6Fe2O3

Directory of Open Access Journals (Sweden)

Ridwan

2009-07-01

Full Text Available Barium hexaferrite (BaO.6Fe2O3 is as a hard magnetic material with good chemical stability which has been intensively used as permanent magnet components. Many works have been done in order to improve their magnetic properties either through chemical process or powders metallurgy technique. In this work, commercial BaO.6Fe2O3 was milled using high-energy milling machine for 10, 20 and 30 hours and followed by reannealing for 3 hours at 1000⁰C in air. X-ray diffraction pattern indicate no phase decomposition occurred caused the mill processing, annealing of milled powders recovered the crystal system and promoted crystallite growth. The magnetic hysteresis curve measured by vibrating sample magnetometer (VSM shows the coercivity of annealed BaO.6Fe2O3 increases to two times higher than the original one. By using Jiles-Atherton model, all the hysteresis parameters Ms, k, α, a and c, have been determined adopted to the Genetic Algorithm (GA. The analyzed hysteretic parameters obtained from this work is congruent to the change of magnetic properties of as-milled and annealed powders of barium hexaferrite.

Cu and Zn substituted silicon clathrates with the cubic type-II structure. Synthesis and characterization of Cs{sub 8}Na{sub 16}Cu{sub 3.8}Si{sub 132.2} and Cs{sub 8}Na{sub 16}Zn{sub 6.9}Si{sub 129.1}

Energy Technology Data Exchange (ETDEWEB)

Schaefer, Marion C.; Bobev, Svilen [Department of Chemistry and Biochemistry, University of Delaware, Newark, DE (United States)

2017-12-13

Studies in the systems Cs-Na-Cu-Si and Cs-Na-Zn-Si yielded the novel clathrates Cs{sub 8}Na{sub 16}(Cu,Si){sub 136} and Cs{sub 8}Na{sub 16}(Zn,Si){sub 136}, both with the cubic type-II structure [space group Fd anti 3m (no. 227), Pearson symbol cF160]. The structures of the title compounds were established from single-crystal X-ray diffraction methods, confirming the complete ordering of the Cs and Na guest atoms. The framework-building Si atoms are found to be randomly substituted by Cu atoms on framework site 96g, exclusively. In the structure of Cs{sub 8}Na{sub 16}(Zn,Si){sub 136}, the refinements indicate that the Zn and Si atoms co-occupy two of the three framework sites with notable preference for site 96g over site 32e. The corresponding refined compositions and unit cell parameters are as follows: Cs{sub 8}Na{sub 16}Cu{sub 3.8}Si{sub 132.2(1)} [a = 14.7583(15) Aa]; Cs{sub 8}Na{sub 16}Zn{sub 6.9}Si{sub 129.1(1)} [a = 14.7682(5) Aa], respectively. The type-II clathrates can be obtained only from experiments employing both Na and Cs, whereas work in the ternary Cs-Cu-Si, Cs-Zn-Si, Na-Cu-Si, and Na-Zn-Si systems failed to yield any clathrate phases. At the same conditions, exploratory studies in the K-Zn-Si and Rb-Zn-Si systems provided evidence that type-I clathrates are favored. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Quasi-epitaxial barium hexaferrite thin films prepared by a topotactic reactive diffusion process

Science.gov (United States)

Meng, Siqin; Yue, Zhenxing; Zhang, Xiaozhi; Li, Longtu

2014-01-01

Quasi-epitaxial barium hexaferrite thin films (BaM) with crystallographic c-axis parallel to film normal were prepared through a topotactic reactive diffusion process using two-step solution deposition on c-plane sapphire. The two-step spin coating process involves preparing an epitaxial hematite film, coating the film with barium precursor solution and thermal annealing. The crystal orientation and magnetic anisotropy of BaM thin films were investigated by X-ray diffraction analysis, SEM observation and magnetic measurements. Hysteresis loops showed good magnetic anisotropy and high remanence ratio (RR) Mr/Ms = 0.97. The films fabricated by two-step spin coating process displayed wider rocking curve width but better magnetic anisotropy than one-step spin coating. The possible mechanism of this discrepancy is discussed in this paper.

Quasi-epitaxial barium hexaferrite thin films prepared by a topotactic reactive diffusion process

Energy Technology Data Exchange (ETDEWEB)

Meng, Siqin; Yue, Zhenxing, E-mail: yuezhx@tsinghua.edu.cn; Zhang, Xiaozhi; Li, Longtu

2014-01-30

Quasi-epitaxial barium hexaferrite thin films (BaM) with crystallographic c-axis parallel to film normal were prepared through a topotactic reactive diffusion process using two-step solution deposition on c-plane sapphire. The two-step spin coating process involves preparing an epitaxial hematite film, coating the film with barium precursor solution and thermal annealing. The crystal orientation and magnetic anisotropy of BaM thin films were investigated by X-ray diffraction analysis, SEM observation and magnetic measurements. Hysteresis loops showed good magnetic anisotropy and high remanence ratio (RR) Mr/Ms = 0.97. The films fabricated by two-step spin coating process displayed wider rocking curve width but better magnetic anisotropy than one-step spin coating. The possible mechanism of this discrepancy is discussed in this paper.

Absence of intrinsic ferromagnetism in Zn1-xMnxO alloys

International Nuclear Information System (INIS)

Zhang Huawei; Shi Erwei; Chen Zhizhan; Liu Xuechao; Xiao Bing

2006-01-01

Zn 1-x Mn x O alloys, with different Mn concentrations, were prepared by the hydrothermal method. X-ray diffraction and electron paramagnetic resonance spectra demonstrate that Zn 2+ ions are homogeneously substituted by Mn 2+ ions without changing the ZnO wurtzite structure. The x = 0.02 and 0.04 samples are paramagnetic. When the Mn concentrations are increased to x = 0.08 and 0.10, the samples exhibit some ferromagnetism due to a secondary phase (Zn,Mn)Mn 2 O 4 . (letter to the editor)

Dielectric behaviour of erbium substituted Mn–Zn ferrites

Indian Academy of Sciences (India)

Unknown

Abstract. Dielectric properties such as dielectric constant (ε′) and dielectric loss tangent (tan δ) of mixed. Mn–Zn–Er ferrites having the compositional formula Mn0⋅58Zn0⋅37Fe2⋅05–xErxO4 (where x = 0⋅2, 0⋅4, 0⋅6, 0⋅8 and. 1⋅0) were measured at room temperature in the frequency range 1–13 MHz using a HP ...

Microwave Characterization of Ba-Substituted PZT and ZnO Thin Films.

Science.gov (United States)

Tierno, Davide; Dekkers, Matthijn; Wittendorp, Paul; Sun, Xiao; Bayer, Samuel C; King, Seth T; Van Elshocht, Sven; Heyns, Marc; Radu, Iuliana P; Adelmann, Christoph

2018-05-01

The microwave dielectric properties of (Ba 0.1 Pb 0.9 )(Zr 0.52 Ti 0.48 )O 3 (BPZT) and ZnO thin films with thicknesses below were investigated. No significant dielectric relaxation was observed for both BPZT and ZnO up to 30 GHz. The intrinsic dielectric constant of BPZT was as high as 980 at 30 GHz. The absence of strong dielectric dispersion and loss peaks in the studied frequency range can be linked to the small grain diameters in these ultrathin films.

Room-temperature ferromagnetic properties of Cu-doped ZnO rod ...

Indian Academy of Sciences (India)

We have investigated properties of the Cu-doped ZnO crystalline film synthesized by the hydrothermal method. X-ray diffraction and X-ray ... DMSs are semiconducting alloys whose lattice is made up in part of substitutional magnetic ... investigate Cu-doped ZnO system (Hou et al 2007a, b), as. Cu is a potential magnetic ion ...

Properties and local environment of p-type and photoluminescent rare earths implanted into ZnO single crystals

CERN Document Server

Rita, EMC; Wahl, U; Soares, JC

This thesis presents an experimental study of the local environment of p-type and Rare- Earth dopants implanted in ZnO single-crystals (SCs). Various nuclear and bulk property techniques were combined in the following evaluations: Implantation damage annealing was evaluated in ZnO SCs implanted with Fe, Sr and Ca. P-type dopants Cu and Ag implanted ZnO SCs were studied revealing that the solubility of Cu in substituting Zn is considerably higher than that of Ag. These results are discussed within the scope of the ZnO p-type doping problematic with these elements. Experimental proofs of the As “anti-site” behavior in ZnO were for the first time attained, i.e., the majority of As atoms are substitutional at the Zn site (SZn), possibly surrounded by two Zn vacancies (VZn). This reinforces the theoretical prediction that As acts as an acceptor in ZnO via the AsZn-2VZn complex formation. The co-doping of ZnO SC with In (donor) and As (acceptor) was addressed. The most striking result is the possible In-As “p...

Effects of Sr-substitution on the structural and magnetic behavior of Ba-based Y-type hexagonal ferrites

International Nuclear Information System (INIS)

Ahmad, Mukhtar; Ali, Qasim; Ali, Ihsan; Ahmad, Ishtiaq; Azhar Khan, M.; Akhtar, Majid Niaz; Murtaza, G.; Rana, M.U.

2013-01-01

Highlights: •Sr-substituted Y-type hexaferrites synthesized by sol–gel method have been investigated. •Platelet grains with well defined hexagonal shape are suitable for microwave absorbers. •Saturation magnetization values were calculated by the law of approach to saturation. •Coercivity of a few hundred oersteds found for all samples is suitable for EM materials. -- Abstract: Sr-substituted samples of Y-type hexagonal ferrites with chemical formula Ba 2−x Sr x Ni 2 Fe 12 O 22 (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were synthesized using the sol–gel autocombustion method and were sintered at 1150 °C for 3 h. The samples were investigated by differential thermal and thermogravimetry analysis, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and vibrating sample magnetometry. X-ray diffraction analysis reveals that single phase samples can be achieved by substituting Sr 2+ ions at Ba 2+ sites in Y-type hexagonal ferrites. X-ray density and bulk density were observed to decrease whereas porosity increased with increasing Sr-concentration. All the samples show well defined hexagonal shape which is favorable for microwave absorbing purposes. The saturation magnetization values were calculated from M–H loops by the law of approach to saturation. The loops show low values of coercivity of a few hundred oersteds which is one of the necessary conditions for electromagnetic (EM) materials and is suitable for security, switching, sensing and high frequency applications

Doping effects of Co2+ ions on ZnO nanorods and their photocatalytic properties

International Nuclear Information System (INIS)

Qiu Xiaoqing; Li Guangshe; Sun Xuefei; Li Liping; Fu Xianzhi

2008-01-01

A series of Zn 1-x Co x O nanorods with dopant content ranging from x = 0.00 to 0.10 was prepared by a wet chemical method. All Zn 1-x Co x O samples were investigated by x-ray diffraction, transmission electron microscopy, energy-dispersion x-ray line mapping analysis, and UV-visible absorption spectroscopy. It was found that Co 2+ ions were homogeneously substituted for Zn 2+ ions in ZnO nanorods. Rhodamine B degradation was used as a probe reaction to evaluate the effect of Co 2+ doping on ZnO nanorods and photocatalytic performance under UV light and visible light irradiation. Co 2+ ions acted as the trapping or recombination centers for electrons and holes, leading to a reduction in photodegradation efficiency under UV light illumination. Alternatively, Co 2+ ions enhanced the optical absorption and produced the photoinduced carriers under visible illumination in terms of two charge transfer transitions involving Co 2+ ions. Consequently, Co 2+ ions substituted in the lattice of ZnO nanorods significantly improved the visible light photocatalytic activity

Defect reactions of implanted Li in ZnSe observed by $\\beta$-NMR

CERN Document Server

Kroll, F; Füllgrabe, M; Mai, F; Marbach, K; Peters, D; Geithner, W; Kappertz, S; Keim, M; Kloos, S; Wilbert, S; Neugart, R; Lievens, P; Georg, U

2001-01-01

Using $\\beta$-radiation-detected nuclear magnetic resonance ($\\beta$-NMR), we investigated the microscopic behavior of implanted $^{8}$Li in nominally undoped ZnSe crystals. From the temperature-dependent amplitudes of high-resolution NMR spectra we conclude a gradual interstitial-to-substitutional site change between 200 and 350 K. This is in accordance with earlier emission channeling results. We argue that this conversion proceeds via Li$_{i}^+$ + V$_{\\textrm{Zn}}^{2-}$ to ${\\textrm{Li}}_{\\textrm{Zn}}^{-}$ and involves implantation-related Zn vacancies. (13 refs).

Sr hexaferrite/Ni ferrite nanocomposites: Magnetic behavior and microwave absorbing properties in the X-band

Energy Technology Data Exchange (ETDEWEB)

Jacobo, Silvia E. [Facultad de Ingeniería, Universidad de Buenos Aires, LAFMACEL-INTECIN, Paseo Colón 850, C1063EHA Buenos Aires (Argentina); Bercoff, Paula G., E-mail: bercoff@famaf.unc.edu.ar [Facultad de Matemática, Astronomía y Física, Universidad Nacional de Córdoba, IFEG, CONICET, Ciudad Universitaria, X5000HUA Córdoba (Argentina); Herme, Carlos A. [Facultad de Ingeniería, Universidad de Buenos Aires, LAFMACEL-INTECIN, Paseo Colón 850, C1063EHA Buenos Aires (Argentina); Vives, Leandro A. [División Antenas, Instituto de Investigaciones Científicas para la Defensa CITEDEF, Ministerio de Defensa, San Juan Bautista de La Salle 4397, Villa Martelli, B1603ALO Buenos Aires (Argentina)

2015-05-01

Nickel ferrite nanoparticles were synthesized by a self-combustion method over nanocrystalline powders of Nd–Co substituted strontium hexaferrite with nominal composition Sr{sub 0.5}Nd{sub 0.5}Co{sub 0.5}Fe{sub 10.5}O{sub 19}, at different mass relations. The samples were structurally characterized by X-ray diffractometry (XRD), scanning electron microscopy (SEM), and energy dispersive X-ray analysis (EDX). The M vs. H loops of the composites were determined with a vibrating sample magnetometer (VSM) and the interaction with the X-band microwave radiation of the nanocomposites dispersed in epoxy resin was measured with a vector network analyzer (VNA). The hysteresis loops showed strong exchange-coupling between the two magnetic phases for the 30:70 and 50:50 Sr{sub 0.5}Co{sub 0.5}Nd{sub 0.5}Fe{sub 10.5}O{sub 19}/NiFe{sub 2}O{sub 4} nanocomposites, while a weak interaction was observed for the 70:30 mass ratio. The nanocomposite with an equal amount of hard and soft phase shows the highest performance both in reflectivity and in bandwidth, reaching a maximum in reflectivity of −34.4 dB at 11.1 GHz while the bandwidth below −10 dB is 3.5 GHz. - Highlights: • Sr{sub 0.5}Co{sub 0.5}Nd{sub 0.5}Fe{sub 10.5}O{sub 19}/NiFe{sub 2}O{sub 4} nanocomposites were synthesized at different mass ratios. • The systems were structurally and magnetically characterized. • The X-band microwave radiation of the composites was evaluated. • Enhancement in reflectivity is related to exchange interaction between hard and soft phases.

Positron annihilation studies of vacancy-type defects and room temperature ferromagnetism in chemically synthesized Li-doped ZnO nanocrystals

International Nuclear Information System (INIS)

Ghosh, S.; Khan, Gobinda Gopal; Mandal, K.; Thapa, Samudrajit; Nambissan, P.M.G.

2014-01-01

Highlights: • Evidence of zinc vacancy-induced intrinsic ferromagnetism in Li-doped ZnO. • Modification of defects and properties through alkali metal substitution. • Study of defect-modification using positron annihilation spectroscopy. • New way to prepare ZnO-based magnetic semiconductor for spintronic applications. -- Abstract: In this article, we have investigated the effects of Li incorporation on the lattice defects and room-temperature d 0 ferromagnetic behaviour in ZnO nanocrystals by correlating X-ray photoelectron, photoluminescence and positron annihilation spectroscopic study in details. It is found that at low doping level ( 1+ is an effective substituent of Zn site, but it prefers to occupy the interstitial positions when Li-doping exceeds 7 at.% resulting in lattice expansion and increase of particle sizes. The pristine ZnO nanocrystals exhibit ferromagnetic behaviour which is further enhanced significantly after few percentage of Li-doping in ZnO. The magnitude of both saturation magnetizations (M S ) as well as the Curie temperature (T C ) are found to increase considerably up to Li concentration of 10 at.% and then started to decrease on further Li-doping. The gradual enhancement of Zn vacancy (V Zn ) defects in ZnO nanocrystals due to Li substitution as confirmed from photoluminescence and positron annihilation spectroscopy measurements might be responsible to induce paramagnetic moments within ZnO host. The ferromagnetic exchange interaction between the localised moments of V Zn defects can be mediated though the holes arising due to Li-substitutional (Li Zn ) acceptor defects within ZnO. Hence, Li doping in ZnO favours in stabilizing considerable V Zn defects and thus helps to sustain long-range high-T C ferromagnetism in ZnO which can be a promising material in future spintronics

Positron annihilation studies of vacancy-type defects and room temperature ferromagnetism in chemically synthesized Li-doped ZnO nanocrystals

Energy Technology Data Exchange (ETDEWEB)

Ghosh, S., E-mail: sghoshphysics@gmail.com [S.N. Bose National Centre for Basic Sciences, Block JD, Sector III, Salt Lake, Kolkata 700098 (India); Khan, Gobinda Gopal [Centre for Research in Nanoscience and Nanotechnology, University of Calcutta, Technology Campus, Block JD2, Sector III, Salt Lake City, Kolkata 700098 (India); Mandal, K. [S.N. Bose National Centre for Basic Sciences, Block JD, Sector III, Salt Lake, Kolkata 700098 (India); Thapa, Samudrajit; Nambissan, P.M.G. [Centre for Research in Nanoscience and Nanotechnology, University of Calcutta, Technology Campus, Block JD2, Sector III, Salt Lake City, Kolkata 700098 (India); Saha Institute of Nuclear Physics, Sector 1, Block AF, Bidhannagar, Kolkata 700064 (India)

2014-03-25

Highlights: • Evidence of zinc vacancy-induced intrinsic ferromagnetism in Li-doped ZnO. • Modification of defects and properties through alkali metal substitution. • Study of defect-modification using positron annihilation spectroscopy. • New way to prepare ZnO-based magnetic semiconductor for spintronic applications. -- Abstract: In this article, we have investigated the effects of Li incorporation on the lattice defects and room-temperature d{sup 0} ferromagnetic behaviour in ZnO nanocrystals by correlating X-ray photoelectron, photoluminescence and positron annihilation spectroscopic study in details. It is found that at low doping level (<7 at.%), Li{sup 1+} is an effective substituent of Zn site, but it prefers to occupy the interstitial positions when Li-doping exceeds 7 at.% resulting in lattice expansion and increase of particle sizes. The pristine ZnO nanocrystals exhibit ferromagnetic behaviour which is further enhanced significantly after few percentage of Li-doping in ZnO. The magnitude of both saturation magnetizations (M{sub S}) as well as the Curie temperature (T{sub C}) are found to increase considerably up to Li concentration of 10 at.% and then started to decrease on further Li-doping. The gradual enhancement of Zn vacancy (V{sub Zn}) defects in ZnO nanocrystals due to Li substitution as confirmed from photoluminescence and positron annihilation spectroscopy measurements might be responsible to induce paramagnetic moments within ZnO host. The ferromagnetic exchange interaction between the localised moments of V{sub Zn} defects can be mediated though the holes arising due to Li-substitutional (Li{sub Zn}) acceptor defects within ZnO. Hence, Li doping in ZnO favours in stabilizing considerable V{sub Zn} defects and thus helps to sustain long-range high-T{sub C} ferromagnetism in ZnO which can be a promising material in future spintronics.

Pressure-induced Polarization Reversal in Z-type Hexaferrite Single Crystal

Science.gov (United States)

Jeon, Byung-Gu; Chun, Sae Hwan; Kim, Kee Hoon

2012-02-01

Multiferroic materials with a gigantic magnetoelectric (ME) coupling at room temperature have been searched for applications to novel devices. Recently, large direct and converse ME effects were realized at room temperature in the so-called Z-type hexaferrite (Ba,Sr)3Co2Fe24O41 single crystals [1,2]. To obtain a new control parameter for realizing a sensitive ME tuning, we studied ME properties of the crystals under uniaxial pressure. Upon applying a tiny uniaxial pressure of about 0.6 GPa, magnetic field-driven electric polarization reversal and anomaly in a M-H loop start to appear at 10 K and gradually disappear at higher temperature above 130 K. By comparing those results with longitudinal magnetostriction at ambient pressure, we propose the pressure-dependent variations of transverse conical spin configuration as well as its domain structure under small magnetic field bias, and point out the possibility of having two different physical origins of the ME coupling in this system. [1] Y. Kitagawa et al., Nat. Mater. 9, 797 (2010) [2] S. H. Chun et al., submitted.

Adsorption of ethyl xanthate on ZnS(110) surface in the presence of water molecules: A DFT study

Energy Technology Data Exchange (ETDEWEB)

Long, Xianhao [School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Chen, Jianhua, E-mail: jhchen@gxu.edu.cn [School of Chemistry and Chemical Engineering, Guangxi University, Nanning 530004 (China); Guangxi Colleges and University Key Laboratory of Minerals Engineering, 530004 (China); Chen, Ye, E-mail: fby18@126.com [College of Resources and Metallurgy, Guangxi University, Nanning 530004 (China)

2016-05-01

Graphical abstract: - Highlights: • Adsorption of water molecules decreases the reactivity of surface Zn atom. • Copper impurities decrease the band gap of ZnS surface. • Copper impurities enhance the adsorption of xanthate on the ZnS surface. • Water molecules have little influence on the properties of Cu-substituted ZnS surface. • The xanthate S atom can interact with the surface S atom of Cu-substituted ZnS surface. - Abstracts: The interaction of collector with the mineral surface plays a very important role in the froth flotation of sphalerite. The adsorptions occurred at the interface between the mineral surface and waters; however most of DFT simulations are performed in vacuum, without consideration of water effect. Semiconductor surface has an obvious proximity effect, which will greatly influence the surface reactivity. To understand the mechanism of xanthate interacting with sphalerite surface in the presence of water molecules, the ethyl xanthate molecule adsorption on un-activated and Cu-activated ZnS(110) surface in the absence and presence of water molecules were performed using the density functional theory (DFT) method. The calculated results show that the adsorption of water molecules dramatically changes the properties of ZnS surface, resulting in decreasing the reactivity of surface Zn atoms with xanthate. Copper activation of ZnS surface changes the surface properties, leading to the totally different adsorption behaviors of xanthate. The presence of waters has little influence on the properties of Cu-activated ZnS surface. The xanthate S atom can interact with the surface S atom of Cu-substituted ZnS surface, which would result in the formation of dixanthogen.

Effect of La-CO substitution on the crystal structure and magnetic properties of low temperature sintered Sr1-xLaxFe12-xCoxO19 (x=0-0.5) ferrites

Science.gov (United States)

Peng, Long; Li, Lezhong; Wang, Rui; Hu, Yun; Tu, Xiaoqiang; Zhong, Xiaoxi

2015-11-01

The La-Co substituted Sr1-xLaxFe12-xCoxO19 (x=0-0.5) ferrites with appropriate Bi2O3 additive were prepared at a low sintering temperature of 890 °C compatible with LTCC (low temperature co-fired ceramics) systems, and the effect of La-Co substitution on their crystal structure and magnetic properties was investigated. The results show that the pure M-type phase is successfully obtained when the La-Co substitution amount x does not exceed 0.3. However, the single M-type phase structure transforms to multiphase structure with further increased x, where the α-Fe2O3 phase and La2O3 phase coexist with the M-type phase. Moreover, the saturation magnetization Ms, magnetic anisotropy field Ha, intrinsic coercivity Hci, and Curie temperature TC of the ferrites depend on the La-Co substitution amount strongly, which are suggested to be determined by the partially substitution of La3+-Co2+ ions for Sr2+-Fe3+ ions with x not higher than 0.3. It is found that the obtained Sr1-xLaxFe12-xCoxO19 (x=0.2 and 0.3) ferrites can provide improved magnetic properties (Ms>62 emu/g, Ha>1400 kA/m, and Hci>320 kA/m) as low temperature sintered M-type hexaferrites for microwave LTCC applications.

The role of annealing temperature and bio template (egg white) on the structural, morphological and magnetic properties of manganese substituted MFe2O4 (M=Zn, Cu, Ni, Co) nanoparticles

Science.gov (United States)

Ranjith Kumar, E.; Jayaprakash, R.; Kumar, Sanjay

2014-02-01

Manganese substituted ferrites (ZnFe2O4, CuFe2O4, NiFe2O4 and CoFe2O4) have been prepared in the bio template medium by using a simple evaporation method. The annealing temperature plays an important position on changing particle size and morphology of the mixed ferrite nanoparticles were found out by X-ray diffraction, transmission electron microscopy and scanning electron microscopy methods. The role of manganese substitution in the mixed ferrite nanoparticles were also analyzed for different annealing temperature. The substitution of Mn also creates a vital change in magnetic properties which is studied by using vibrating sample magnetometer (VSM). These spinel ferrites are decomposed to α-Fe2O3 after annealing above 550 °C in air. However, α-Fe2O3 phase was slowly vanished after ferrites annealing above 900 °C. The effect of this secondary phase on the structural change and magnetic properties of the mixed ferrite nanoparticles is discussed.

High Temperature Thermoelectric Properties of ZnO Based Materials

DEFF Research Database (Denmark)

Han, Li

of the dopants and dopant concentrations, a large power factor was obtainable. The sample with the composition of Zn0.9Cd0.1Sc0.01O obtained the highest zT ∼0.3 @1173 K, ~0.24 @1073K, and a good average zT which is better than the state-of-the-art n-type thermoelectric oxide materials. Meanwhile, Sc-doped Zn......This thesis investigated the high temperature thermoelectric properties of ZnO based materials. The investigation first focused on the doping mechanisms of Al-doped ZnO, and then the influence of spark plasma sintering conditions on the thermoelectric properties of Al, Ga-dually doped Zn......O. Following that, the nanostructuring effect for Al-doped ZnO was systematically investigated using samples with different microstructure morphologies. At last, the newly developed ZnCdO materials with superior thermoelectric properties and thermal stability were introduced as promising substitutions...

Molecular mechanism of Zn2+ agonism in the extracellular domain of GPR39

DEFF Research Database (Denmark)

Storjohann, Laura; Holst, Birgitte; Schwartz, Thue W

2008-01-01

-terminal segment. Surprisingly, substitution of Asp313 located in extracellular loop 3 greatly increased ligand-independent signaling and apparently eliminated Zn2+-induced activation. It is proposed that Zn2+ acts as an agonist for GPR39, not in the classical manner by directly stabilizing an active conformation...

Ammonia sensing properties of V-doped ZnO:Ca nanopowders prepared by sol–gel synthesis

International Nuclear Information System (INIS)

Fazio, E.; Hjiri, M.; Dhahri, R.; El Mir, L.; Sabatino, G.; Barreca, F.; Neri, F.; Leonardi, S.G.; Pistone, A.; Neri, G.

2015-01-01

V-doped ZnO:Ca nanopowders with different V loading were prepared by sol–gel synthesis and successive drying in ethanol under supercritical conditions. Characterization data of nanopowders annealed at 700 °C in air, revealed that they have the wurtzite structure. Raman features of V-doped ZnO:Ca samples were found to be substantially modified with respect to pure ZnO or binary ZnO:Ca samples, which indicate the substitution of vanadium ions in the ZnO lattice. The ammonia sensing properties of V-doped ZnO:Ca thick films were also investigated. The results obtained demonstrate the possibility of a fine tuning of the sensing characteristics of ZnO-based sensors by Ca and V doping. In particular, their combined effect has brought to an enhanced response towards NH 3 compared to bare ZnO and binary V-ZnO and Ca-ZnO samples. Raman investigation suggested that the presence of Ca play a key role in enhancing the sensor response in these ternary composite nanomaterials. - Graphical abstract: V-doped ZnO:Ca nanopowders prepared by sol–gel synthesis possess enhanced sensing characteristics towards NH 3 compared to bare ZnO. - Highlights: • V-doped ZnO:Ca nanopowders with different V loading were prepared by sol–gel synthesis. • Raman features of V-doped ZnO:Ca samples indicate the substitution of V ions in the ZnO lattice. • Combined effects of dopants have brought to an enhanced response to NH 3 compared to ZnO. • Ca play a key role in enhancing the sensor response of ternary V-doped ZnO:Ca composites

Li(Zn,Co,MnAs: A bulk form diluted magnetic semiconductor with Co and Mn co-doping at Zn sites

Directory of Open Access Journals (Sweden)

Bijuan Chen

2016-11-01

Full Text Available We report the synthesis and characterization of a series of bulk forms of diluted magnetic semiconductors Li(Zn1-x-yCoxMnyAs with a crystal structure close to that of III-V diluted magnetic semiconductor (Ga,MnAs. No ferromagnetic order occurs with single (Zn,Co or (Zn, Mn substitution in the parent compound LiZnAs. Only with co-doped Co and Mn ferromagnetic ordering can occur at the Curie temperature ∼40 K. The maximum saturation moment of the this system reached to 2.17μB/Mn, which is comparable to that of Li (Zn,MnAs. It is the first time that a diluted magnetic semiconductor with co-doping Co and Mn into Zn sites is achieved in “111” LiZnAs system, which could be utilized to investigate the basic science of ferromagnetism in diluted magnetic semiconductors. In addition, ferromagnetic Li(Zn,Co,MnAs, antiferromagnetic LiMnAs, and superconducting LiFeAs share square lattice at As layers, which may enable the development of novel heterojunction devices in the future.

Composition influence on positron annihilation parameters in ZnO-based nanocrystal semiconductor powders

Energy Technology Data Exchange (ETDEWEB)

Damonte, L.C.; Hernandez Fenollosa, M.A.; Donderis, V.; Mari, B. [Departamento de Fisica Aplicada, Universidad Politecnica de Valencia, Cami de Vera s/n, Valencia, 46071 (Spain)

2007-07-01

Zn{sub 1-x}Mg{sub x}O powders at various compositions were obtained by mechanical milling from the binary oxides. The progressive incorporation of Mg atoms into the ZnO lattice was monitored by X-ray diffraction (XRD). The evolution of annihilation parameters with milling time and composition were analyzed and related to the possible types of mechanical and substitutional induced defect present. It was concluded that the average lifetime constitute a useful parameter to sense the complete cation substitution in the wurtzite structure. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Composition influence on positron annihilation parameters in ZnO-based nanocrystal semiconductor powders

International Nuclear Information System (INIS)

Damonte, L.C.; Hernandez Fenollosa, M.A.; Donderis, V.; Mari, B.

2007-01-01

Zn 1-x Mg x O powders at various compositions were obtained by mechanical milling from the binary oxides. The progressive incorporation of Mg atoms into the ZnO lattice was monitored by X-ray diffraction (XRD). The evolution of annihilation parameters with milling time and composition were analyzed and related to the possible types of mechanical and substitutional induced defect present. It was concluded that the average lifetime constitute a useful parameter to sense the complete cation substitution in the wurtzite structure. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Simultaneous increase in strength and ductility by decreasing interface energy between Zn and Al phases in cast Al-Zn-Cu alloy.

Science.gov (United States)

Han, Seung Zeon; Choi, Eun-Ae; Park, Hyun Woong; Lim, Sung Hwan; Lee, Jehyun; Ahn, Jee Hyuk; Hwang, Nong-Moon; Kim, Kwangho

2017-09-22

Cast-Al alloys that include a high amount of the second element in their matrix have comparatively high strength but low ductility because of the high volume fraction of strengthening phases or undesirable inclusions. Al-Zn alloys that have more than 30 wt% Zn have a tensile strength below 300 MPa, with elongation under 5% in the as-cast state. However, we found that after substitution of 2% Zn by Cu, the tensile strength of as-cast Al-Zn-Cu alloys was 25% higher and ductility was four times higher than for the corresponding Al-35% Zn alloy. Additionally, for the Al-43% Zn alloy with 2% Cu after 1 h solution treatment at 400 °C and water quenching, the tensile strength unexpectedly reached values close to 600 MPa. For the Al-33% Zn alloy with 2% Cu, the tensile strength was 500 MPa with 8% ductility. The unusual trends of the mechanical properties of Al-Zn alloys with Cu addition observed during processing from casting to the subsequent solution treatment were attributed to the precipitation of Zn in the Al matrix. The interface energy between the Zn particles and the Al matrix decreased when using a solution of Cu in Zn.

Effect of thickness on microwave absorptive behavior of La-Na doped Co-Zr barium hexaferrites in 18.0–26.5 GHz band

Energy Technology Data Exchange (ETDEWEB)

Arora, Amit [D.A.V. Institute of Engineering and Technology, Jalandhar (India); Narang, Sukhleen Bindra, E-mail: sukhleen2@yahoo.com [Department of Electronics Technology, Guru Nanak Dev University, Amritsar (India); Pubby, Kunal [Department of Electronics Technology, Guru Nanak Dev University, Amritsar (India)

2017-02-01

In this research, the microwave properties of Lanthanum-Sodium doped Cobalt-Zirconium barium hexaferrites, intended as microwave absorbers, are analyzed on Vector Network Analyzer in K-band. The results indicate that the doping has resulted in lowering of real permittivity and enhancement of dielectric losses. Real permeability has shown increase while magnetic losses have shown decrease in value with doping. All these four properties have shown very small variation with frequency in the scanned frequency range which indicates the relaxation type of behavior. Microwave absorption characteristics of these compositions are analyzed with change in sample thickness. The results demonstrate that the matching frequency of the microwave absorber shifts towards lower side of frequency band with increase in thickness. The complete analysis of the prepared microwave absorbers shows a striking achievement with very low reflection loss and wide absorption bandwidth for all the six compositions in 18–26.5 GHz frequency band. - Highlights: • Electromagnetic Characterization of M-hexaferrites in K-band (18–26.5 GHz) • Variation of absorption properties with thickness of sample. • Satisfaction of quarter-wavelength condition for absorption properties • Results of double-layer absorbers (not reports till day by anyone).

Effect of calcination temperature on microstructure, dielectric, magnetic and optical properties of Ba{sub 0.7}La{sub 0.3}Fe{sub 11.7}Co{sub 0.3}O{sub 19} hexaferrites

Energy Technology Data Exchange (ETDEWEB)

Kaur, Talwinder [Department of Physics, Lovely Professional University, Phagwara, Punjab 144411 (India); Kaur, Barjinder [Department of Physics, National Institute of Technology, Jalandhar 144011 (India); Bhat, Bilal H. [Department of Physics, University of Kashmir, 190006 (India); Kumar, Sachin [Department of Chemistry, Guru Nanak Dev University, Amritsar 143005 (India); Srivastava, A.K., E-mail: srivastava_phy@yahoo.co.in [Department of Physics, Lovely Professional University, Phagwara, Punjab 144411 (India)

2015-01-01

M-type barium hexaferrite Ba{sub 0.7}La{sub 0.3}Fe{sub 11.7}Co{sub 0.3}O{sub 19} (BaLCM) powder, synthesized using sol gel auto combustion method, heat treated at 700, 900, 1100 and 1200 °C. X ray diffraction (XRD) powder patterns of heat treated samples show the formation of pure phase of M-type hexaferrite after 700 °C. Thermo gravimetric analysis (TGA) reveals that the weight loss of BaLCM becomes constant after 680 °C. The presence of two prominent peaks, at 432 cm{sup −1} and 586 cm{sup −1} in Fourier Transform Infrared Spectroscopy (FT-IR) spectra, gives the idea of formation of M-type hexaferrites. The M–H curve obtained from Vibrating Sample Magnetometer (VSM) were used to calculate saturation magnetization (M{sub S}), retentivity (M{sub r}), squareness ration (SR) and coercivity (H{sub c}). The maximum value of coercivity (5602 Oe) is found at 900 °C. The band gap dependency on temperature was studied using UV–vis NIR spectroscopy. The dielectric constant has been found to be high at low frequency but it decreases with increase in frequency. Such kind of dielectric behavior is explained on the basis of Koop's phenomenological theory and Maxwell Wagner theory.

Quinoline-substituted Zinc(II) phthalocyanine for the dual detection of ferric and zinc ions

Energy Technology Data Exchange (ETDEWEB)

Gupta, Ankush [Lyallpur Khalsa College of Engineering, Jalandhar (India); Kim, A Rong [Dong-A University, Busan (Korea, Republic of); Kim, Kyung Sub; Na, Kun [The Catholic University, Seoul (Korea, Republic of); Choi, Myung Seok [Konkuk University, Seoul (Korea, Republic of); Park, Jong S. [Pusan National University, Busan (Korea, Republic of)

2015-09-15

Here we present the synthesis and properties of quinoline-substituted zinc(II) phthalocyanine, Zn[Pc(O-QN){sub 4} ]. Zn[Pc(O-QN){sub 4} ] can function as a highly selective chemosensor against Fe{sup 3+} and Zn{sup 2+} ions, exhibiting efficient fluorescence quenching and enhancement, respectively. Various characterization techniques were employed to investigate the intermolecular interactions of Zn[Pc(O-QN){sub 4} ] with metal ions. A double-electron exchange and a forbidden photoinduced electron transfer behavior in Zn[Pc(O-QN){sub 4} ] were attributed to such opposite responses. Furthermore, by taking advantage of selectivity, we successfully employed Zn[Pc(O-QN)-4 ] to stain and record confocal fluorescence microscopy images of Chang liver cells in the presence of metal ions.

Enhanced magnetic domain relaxation frequency and low power losses in Zn{sup 2+} substituted manganese ferrites potential for high frequency applications

Energy Technology Data Exchange (ETDEWEB)

Praveena, K., E-mail: praveenaou@gmail.com [Department of Physics, National Taiwan Normal University, Taipei, 11677, Taiwan (China); Chen, Hsiao-Wen [Department of Physics, National Taiwan Normal University, Taipei, 11677, Taiwan (China); Liu, Hsiang-Lin, E-mail: hliu@ntnu.edu.tw [Department of Physics, National Taiwan Normal University, Taipei, 11677, Taiwan (China); Sadhana, K., E-mail: sadhana@osmania.ac.in [Department of Physics, Osmania University, Saifabad, Hyderabad, 500004 (India); Murthy, S.R. [Department of Physics, Osmania University, Hyderabad, 500007 (India)

2016-12-15

Nowadays electronic industries prerequisites magnetic materials, i.e., iron rich materials and their magnetic alloys. However, with the advent of high frequency applications, the standard techniques of reducing eddy current losses, using iron cores, were no longer efficient or cost effective. Current market trends of the switched mode power supplies industries required even low energy losses in power conversion with maintenance of adequate initial permeability. From the above point of view, in the present study we aimed at the production of Manganese–Zinc ferrites prepared via solution combustion method using mixture of fuels and achieved low loss, high saturation magnetization, high permeability, and high magnetic domain relaxation frequency. The as-synthesized Zn{sup 2+} substituted MnFe{sub 2}O{sub 4} were characterized by X-ray diffractometer (XRD) and transmission electron microscopy (TEM). The fractions of Mn{sup 2+}, Zn{sup 2+} and Fe{sup 2+} cations occupying tetrahedral sites along with Fe occupying octahedral sites within the unit cell of all ferrite samples were estimated by Raman scattering spectroscopy. The magnetic domain relaxation was investigated by inductance spectroscopy (IS) and the observed magnetic domain relaxation frequency (f{sub r}) was increased with the increase in grain size. The real and imaginary part of permeability (μ′ and μ″) increased with frequency and showed a maximum above 100 MHz. This can be explained on the basis of spin rotation and domain wall motion. The saturation magnetization (M{sub s}), remnant magnetization (M{sub r}) and magneton number (µ{sub B}) decreased gradually with increasing Zn{sup 2+} concentration. The decrease in the saturation magnetization was discussed with Yafet–Kittel (Y–K) model. The Zn{sup 2+} concentration increases the relative number of ferric ions on the A sites, reduces the A–B interactions. The frequency dependent total power losses decreased as the zinc concentration increased

Suppression and enhancement of deep level emission of ZnO on Si4+ & V5+ substitution

Science.gov (United States)

Srivastava, T.; Bajpai, G.; Sen, S.

2018-03-01

ZnO possess a wide range of tunable properties depending on the type and concentration of dopant. Defects in ZnO due to doped aliovalent ions can generate certain functionalities. Such defects in the lattice do not deteriorate the material properties but actually modifies the material towards infinite number of possibilities. Defects like oxygen vacancies play a significant role in photocatalytic and sensing applications. Depending upon the functionality, defect state of ZnO can be modified by suitable doping. Amount and nature of different dopant has different effect on defect state of ZnO. It depends upon the ionic radii, valence state, chemical stability etc. of the ion doped. Two samples with two different dopants i.e., silicon and vanadium, Zn1-xSixO and Zn1-xVxO, for x=0 & 0.020, were synthesized using solgel method (a citric acid-glycerol route) followed by solid state sintering. A comparison of their optical properties, photoluminescence and UV-Vis spectroscopy, with pure ZnO was studied at room temperature. Silicon doping drastically reduces whereas vanadium doping enhances the green emission as compared with pure ZnO. Suppression and enhancement of defect levels (DLE) is rationalized by the effects of extra charge present on Si4+ & V5+ (in comparison to Zn2+) and formation of new hybrid state (V3d O2p) within bandgap. Reduction of defects in Zn1-xSixO makes it suitable material for opto-electronics application whereas enhancement in defects in Zn1-xVxO makes it suitable material for photocatalytic as well as gas sensing application.

Syntheses and Photodynamic Activity of Pegylated Cationic Zn(II-Phthalocyanines in HEp2 Cells

Directory of Open Access Journals (Sweden)

Benson G. Ongarora, Xiaoke Hu, Susan D. Verberne-Sutton, Jayne C. Garno, M. Graça H. Vicente

2012-01-01

Full Text Available Di-cationic Zn(II-phthalocyanines (ZnPcs are promising photosensitizers for the photodynamic therapy (PDT of cancers and for photoinactivation of viruses and bacteria. Pegylation of photosensitizers in general enhances their water-solubility and tumor cell accumulation. A series of pegylated di-cationic ZnPcs were synthesized from conjugation of a low molecular weight PEG group to a pre-formed Pc macrocycle, or by mixed condensation involving a pegylated phthalonitrile. All pegylated ZnPcs were highly soluble in polar organic solvents but were insoluble in water; they have intense Q absorptions centered at 680 nm and fluorescence quantum yields of ca. 0.2 in DMF. The non-pegylated di-cationic ZnPc 6a formed large aggregates, which were visualized by atomic force microscopy. The cytotoxicity, cellular uptake and subcellular distribution of all cationic ZnPcs were investigated in human carcinoma HEp2 cells. The most phototoxic compounds were found to be the α-substituted Pcs. Among these, Pcs 4a and 16a were the most effective (IC50 ca. 10 μM at 1.5 J/cm2, in part due to the presence of a PEG group and the two positive charges in close proximity (separated by an ethylene group in these macrocycles. The β-substituted ZcPcs 6b and 4b accumulated the most within HEp2 cells but had low photocytoxicity (IC50 > 100 μM at 1.5 J/cm2, possibly as a result of their lower electron density of the ring and more extended conformations compared with the α-substituted Pcs. The results show that the charge distribution about the Pc macrocycle and the intracellular localization of the cationic ZnPcs mainly determine their photodynamic activity.

Structural and magnetic properties of Ni-Zn and Ni-Zn-Co ferrites

Energy Technology Data Exchange (ETDEWEB)

Knyazev, A.V., E-mail: knyazevav@gmail.com [N.I. Lobachevsky State University of Nizhni Novgorod, Gagarin Prospekt 23/2, 603950 Nizhni Novgorod (Russian Federation); Zakharchuk, I.; Lähderanta, E. [Lappeenranta University of Technology, P.O. Box 20, FI-53851 Lappeenranta (Finland); Baidakov, K.V.; Knyazeva, S.S. [N.I. Lobachevsky State University of Nizhni Novgorod, Gagarin Prospekt 23/2, 603950 Nizhni Novgorod (Russian Federation); Ladenkov, I.V. [Joint-stock Company “Research and Production Company “Salut”, Nizhni Novgorod (Russian Federation)

2017-08-01

Highlights: • Ni-Zn and Ni-Zn-Co ferrite powders were prepared by the solid-state reaction at 1073 K. • The room temperature saturation magnetizations are 59.7 emu/g for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 57.1 emu/g for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. • The coercivity of the samples is found to be much larger than that of bulk ferrites and increases with Co introduction. • The temperature dependences of magnetization exhibit large spin frustration and spin-glass-like behavior. - Abstract: Ni-Zn and Ni-Zn-Co ferrite powders with nominal compositions Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4} were prepared by the solid-state reaction synthesis with periodic regrinding during the calcination at 1073 K. The structure of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4} was refined assuming space group F d-3m. Scanning electron microscopy revealed the average sizes of the crystalline ferrite particles are 130–630 nm for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 140–350 nm for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. The room temperature saturation magnetizations are 59.7 emu/g for Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} and 57.1 emu/g for Ni{sub 0.5}Zn{sub 0.3}Co{sub 0.2}Fe{sub 2}O{sub 4}. The coercivity of the samples is found to be much larger than that of bulk ferrites and increases with Co introduction. The Curie temperature tends to increase upon Zn substitution by Co, as well. The temperature dependences of magnetization measured using zero-field cooled and field cooled protocols exhibit large spin frustration and spin-glass-like behavior.

Effects of Sr-substitution on the structural and magnetic behavior of Ba-based Y-type hexagonal ferrites

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Mukhtar, E-mail: mukhtarahmad25@gmail.com [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Ali, Qasim; Ali, Ihsan; Ahmad, Ishtiaq [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Azhar Khan, M. [Department of Physics, The Islamia University of Bahawalpur 63100 (Pakistan); Akhtar, Majid Niaz [Department of Physics, COMSATS Institute of Information Technology, Lahore (Pakistan); Murtaza, G. [Centre for Advanced Studies in Physics, G.C. University, Lahore (Pakistan); Rana, M.U., E-mail: mazharrana@bzu.edu.pk [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan)

2013-12-15

Highlights: •Sr-substituted Y-type hexaferrites synthesized by sol–gel method have been investigated. •Platelet grains with well defined hexagonal shape are suitable for microwave absorbers. •Saturation magnetization values were calculated by the law of approach to saturation. •Coercivity of a few hundred oersteds found for all samples is suitable for EM materials. -- Abstract: Sr-substituted samples of Y-type hexagonal ferrites with chemical formula Ba{sub 2−x}Sr{sub x}Ni{sub 2}Fe{sub 12}O{sub 22} (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were synthesized using the sol–gel autocombustion method and were sintered at 1150 °C for 3 h. The samples were investigated by differential thermal and thermogravimetry analysis, X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy and vibrating sample magnetometry. X-ray diffraction analysis reveals that single phase samples can be achieved by substituting Sr{sup 2+} ions at Ba{sup 2+} sites in Y-type hexagonal ferrites. X-ray density and bulk density were observed to decrease whereas porosity increased with increasing Sr-concentration. All the samples show well defined hexagonal shape which is favorable for microwave absorbing purposes. The saturation magnetization values were calculated from M–H loops by the law of approach to saturation. The loops show low values of coercivity of a few hundred oersteds which is one of the necessary conditions for electromagnetic (EM) materials and is suitable for security, switching, sensing and high frequency applications.

Intrinsic point-defect balance in self-ion-implanted ZnO.

Science.gov (United States)

Neuvonen, Pekka T; Vines, Lasse; Svensson, Bengt G; Kuznetsov, Andrej Yu

2013-01-04

The role of excess intrinsic atoms for residual point defect balance has been discriminated by implanting Zn or O ions into Li-containing ZnO and monitoring Li redistribution and electrical resistivity after postimplant anneals. Strongly Li-depleted regions were detected in the Zn-implanted samples at depths beyond the projected range (R(p)) upon annealing ≥ 600 °C, correlating with a resistivity decrease. In contrast, similar anneals of the O-implanted samples resulted in Li accumulation at R(p) and an increased resistivity. Control samples implanted with Ar or Ne ions, yielding similar defect production as for the Zn or O implants but with no surplus of intrinsic atoms, revealed no Li depletion. Thus, the depletion of Li shows evidence of excess Zn interstitials (Zn(I)) being released during annealing of the Zn-implanted samples. These Zn(I)'s convert substitutional Li atoms (Li(Zn)) into highly mobile interstitial ones leading to the strongly Li-depleted regions. In the O-implanted samples, the high resistivity provides evidence of stable O(I)-related acceptors.

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

International Nuclear Information System (INIS)

Ferreira, J.R.M.; Louro, L.H.L.; Costa, A.M.; Silva, M.H. Prado da; Campos, J.B. de

2016-01-01

In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD) to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite. (author)

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

Energy Technology Data Exchange (ETDEWEB)

Ferreira, J.R.M.; Louro, L.H.L.; Costa, A.M.; Silva, M.H. Prado da [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil); Campos, J.B. de, E-mail: josericardo@r-crio.com, E-mail: louro@ime.eb.br, E-mail: andrea@r-crio.com, E-mail: brantjose@gmail.com, E-mail: marceloprado@ime.eb.br [Universidade do Estado do Rio de Janeiro (UERJ), Rio de Janeiro, RJ (Brazil)

2016-10-15

In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD) to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite. (author)

Magnetic Properties and Structural Characteristics of BaFe12O19 Hexaferrites Synthesized by the Zol-Gel Combustion

Science.gov (United States)

Zhuravlev, V. A.; Itin, V. I.; Minin, R. V.; Lopushnyak, Yu. M.; Velikanov, D. A.

2018-03-01

The phase structure, structural parameters, and basic magnetic characteristics of BaFe12O19 hexaferrites prepared by the zol-gel combustion method with subsequent annealing at a temperature of 850°C for 6 h are investigated. The influence of the organic fuel type on the properties of synthesized materials is analyzed. Values of the saturation magnetization and the anisotropy field are determined. It is established that they depend on the organic fuel type. It is shown that powders synthesized with citric acid used as a fuel have the largest particle sizes and the highest saturation magnetization.

Effects of magnetic pre-alignment of nano-powders on formation of high textured barium hexa-ferrite quasi-single crystals via a magnetic forming and liquid participation sintering route

International Nuclear Information System (INIS)

Liu, Junliang; Zeng, Yanwei; Zhang, Xingkai; Zhang, Ming

2015-01-01

Highly textured barium hexa-ferrite quasi-single crystal with narrow ferromagnetic resonance line-width is believed to be a potential gyromagnetic material for self-biased microwave devices. To fabricate barium hexa-ferrite quasi-single crystal with a high grain orientation degree, a magnetic forming and liquid participation sintering route has been developed. In this paper, the effects of the pre-alignment of the starting nano-powders on the formation of barium quasi-single crystal structures have been investigated. The results indicated that: the crystallites with large sizes and small specific surfaces were easily aligned for they got higher driving forces and lower resistances during magnetic forming. The average restricting magnetic field was about 4.647 kOe to overcome the average friction barrier between crystallites. The pre-aligned crystallites in magnetic forming acted as the “crystal seeds” for oriented growth of the un-aligned crystallites during liquid participation sintering to achieve a high grain orientation. To effectively promote the grain orientation degrees of the sintered pellets, the grain orientation degrees of the green compacts must be higher than a limited value of 15.0%. Barium hexa-ferrite quasi-single crystal with a high grain orientation degree of 98.6% was successfully fabricated after sintering the green compact with its grain orientation degree of 51.1%. - Highlights: • Aligned particles acted as “crystal seeds” for un-aligned ones' oriented growth. • Magnetic field of 4.647 kOe was needed to overcome crystallites' friction barrier. • GOD dramatically increased after sintering if starting GOD exceeded to 15.0%. • Quasi-single crystal was prepared by sintering green compact with GOD of 51.1%

Effects of magnetic pre-alignment of nano-powders on formation of high textured barium hexa-ferrite quasi-single crystals via a magnetic forming and liquid participation sintering route

Energy Technology Data Exchange (ETDEWEB)

Liu, Junliang, E-mail: liujunliang@yzu.edu.cn [Key Laboratory of Environmental Materials and Engineering of Jiangsu Province, School of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002 (China); Zeng, Yanwei [State Key Laboratory of Materials-Oriented Chemical Engineering, School of Materials Science and Engineering, Nanjing Tech University, Nanjing 210009 (China); Zhang, Xingkai [Key Laboratory of Environmental Materials and Engineering of Jiangsu Province, School of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002 (China); Zhang, Ming [Key Laboratory of Environmental Materials and Engineering of Jiangsu Province, School of Chemistry and Chemical Engineering, Yangzhou University, Yangzhou 225002 (China); Testing Center of Yangzhou University, Yangzhou 225002 (China)

2015-05-15

Highly textured barium hexa-ferrite quasi-single crystal with narrow ferromagnetic resonance line-width is believed to be a potential gyromagnetic material for self-biased microwave devices. To fabricate barium hexa-ferrite quasi-single crystal with a high grain orientation degree, a magnetic forming and liquid participation sintering route has been developed. In this paper, the effects of the pre-alignment of the starting nano-powders on the formation of barium quasi-single crystal structures have been investigated. The results indicated that: the crystallites with large sizes and small specific surfaces were easily aligned for they got higher driving forces and lower resistances during magnetic forming. The average restricting magnetic field was about 4.647 kOe to overcome the average friction barrier between crystallites. The pre-aligned crystallites in magnetic forming acted as the “crystal seeds” for oriented growth of the un-aligned crystallites during liquid participation sintering to achieve a high grain orientation. To effectively promote the grain orientation degrees of the sintered pellets, the grain orientation degrees of the green compacts must be higher than a limited value of 15.0%. Barium hexa-ferrite quasi-single crystal with a high grain orientation degree of 98.6% was successfully fabricated after sintering the green compact with its grain orientation degree of 51.1%. - Highlights: • Aligned particles acted as “crystal seeds” for un-aligned ones' oriented growth. • Magnetic field of 4.647 kOe was needed to overcome crystallites' friction barrier. • GOD dramatically increased after sintering if starting GOD exceeded to 15.0%. • Quasi-single crystal was prepared by sintering green compact with GOD of 51.1%.

Effect of ZnO and PbO/ZnO on structural and thermal properties of tellurite glasses

International Nuclear Information System (INIS)

Ramamoorthy, Raj Kumar; Bhatnagar, Anil K

2015-01-01

Highlights: • Structural units/linkages variation of TeO 2 -ZnO and TeO 2 -ZnO-PbO glasses was studied. • Structural arrangements of TeO 2 -ZnO glasses are rich in Te-O-Te network. • A mixture of Te-O-Te and Te-O-Pb networks is identified in TeO 2 -ZnO-PbO glasses. • Changes in thermal parameters T g and T o are correlated with the structural variations. • 15PbO and 20PbO samples of TeO 2 -ZnO-PbO glasses show large thermal stability. - Abstract: Two series of glasses, (100 − x)TeO 2 -xZnO (x = 20, 25, 30, 35) and 70TeO 2 -(30 − y)ZnO-yPbO (y = 5, 10, 15, 20), referred as TZ and TZP, respectively, were prepared by a melt quenching technique and characterized by X-ray diffraction (XRD), density, refractive index, Raman scattering and differential scanning calorimetry (DSC) to observe the changes in their properties as a function of ZnO and PbO/ZnO. Variations in individual structural units/linkages in these glasses are derived from the de-convoluted Raman spectra. The glass transition (T g ) and onset of crystallization (T o ) temperatures are determined from DSC isothermal scans. It is observed that the thermal stability (ΔT = T o − T g ) decreases for TZ glasses with increase in x, while it increases for TZP glasses with increase in y. Changes in thermal parameters of these glasses are correlated with the structural variation as a function of ZnO and PbO/ZnO ratio to determine the effect of substitution/addition of metal oxide, ZnO and PbO, to TeO 2 and TeO 2 -ZnO glasses

Growing barium hexaferrite (BaFe{sub 12}O{sub 19}) thin films using chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Budiawanti, Sri, E-mail: awanty77@yahoo.com [Graduate Program of Materials Science, Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia); Faculty of Teacher Training and Education, Sebelas Maret University (Indonesia); Soegijono, Bambang [Multiferroic Laboratory, Department of Physics, FMIPA, Universitas Indonesia, Kampus UI Depok (Indonesia)

2016-04-19

Barium hexaferrite (BaFe{sub 12}O{sub 19}, or simply known as BaM) thin films has been recognized as a potential candidate for microwave-based devices, magnetic recording media and data storage. To grow BaM thin films, chemical solution deposition is conducted using the aqueous solution of metal nitrates, which involves spin coatings on Si substrates. Furthermore, Thermal Gravimeter Analysis (TGA), X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM) and Vibrating Sample Magnetometer (VSM) are applied to evaluate the decomposition behavior, structure, morphology, and magnetic properties of BaM thin films. Additionally, the effects of number of layers variation are also investigated. Finally, magnetic properties analysis indicates the isotropic nature of the films.

Growing barium hexaferrite (BaFe_1_2O_1_9) thin films using chemical solution deposition

International Nuclear Information System (INIS)

Budiawanti, Sri; Soegijono, Bambang

2016-01-01

Barium hexaferrite (BaFe_1_2O_1_9, or simply known as BaM) thin films has been recognized as a potential candidate for microwave-based devices, magnetic recording media and data storage. To grow BaM thin films, chemical solution deposition is conducted using the aqueous solution of metal nitrates, which involves spin coatings on Si substrates. Furthermore, Thermal Gravimeter Analysis (TGA), X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM) and Vibrating Sample Magnetometer (VSM) are applied to evaluate the decomposition behavior, structure, morphology, and magnetic properties of BaM thin films. Additionally, the effects of number of layers variation are also investigated. Finally, magnetic properties analysis indicates the isotropic nature of the films.

Impact of ZnO substitution on magnetic response and microwave absorption capability of strontium-natural nanoferrites

Directory of Open Access Journals (Sweden)

W. Widanarto

2015-01-01

Full Text Available Ferrite being a compound derived from iron oxides including magnetite and hematite possesses similar properties as ceramics which are hard and brittle. Certainly, the mounting demand for electronics has been a major factor driving the exponential growth of ferrite based materials. ZnO doped strontium-natural nanoferrites of composition (80 − xFe2O3:xZnO:20SrCO3, where x = 0, 10, 20 mol% are synthesized and sintered via the solid state reaction scheme. Samples are characterized by SEM, XRD, VSM, and VNA measurements to determine the impact of ZnO contents’ variation on the surface morphology, structure, magnetic and microwave absorption properties. The Nicolson–Ross–Weir method is applied to evaluate samples’ reflection loss. The average grain size of the strontium ferrite is found to reduce with the increase in ZnO concentration. Materials sintered at 1100 °C without ZnO incorporation are composed of hexagonal SrFe12O19. Meanwhile, the addition of ZnO produces cubic ZnFe2O4 and SrFeO2 phases. Insertion of ZnO results in reduction of magnetic parameters and reflection loss. Furthermore, the anisotropy magnetic field of strontium natural ferrites displays a rapid drop from 350 kA/m to 79.6 kA/m with the increase in ZnO. Strontium ferrite containing 20 mol% of ZnO exhibits superior microwave absorption with reflection loss within −45 dB to −55.94 dB in the frequency range of 7–13 GHz. This facilely synthesized a new class of materials which is believed to be economically promising for microwave absorption applications in the GHz range.

Type II photoinitiator substituted zinc phthalocyanine: Synthesis, photophysical and photopolymerization studies

Energy Technology Data Exchange (ETDEWEB)

Korkut, Sibel Eken [Department of Chemistry, Yıldız Technical University, 34210 Davutpaşa, İstanbul (Turkey); Temel, Gokhan [Department of Polymer Engineering, Yalova University, 77100 Yalova (Turkey); Balta, Demet Karaca [Department of Chemistry, Yıldız Technical University, 34210 Davutpaşa, İstanbul (Turkey); Arsu, Nergis, E-mail: narsu@yildiz.edu.tr [Department of Chemistry, Yıldız Technical University, 34210 Davutpaşa, İstanbul (Turkey); Şener, M. Kasım, E-mail: mkasimsener@gmail.com [Department of Chemistry, Yıldız Technical University, 34210 Davutpaşa, İstanbul (Turkey)

2013-04-15

The novel 4-(9-oxo-9 H-thioxanthen-2yloxy) phthalonitrile (TX-Pht) and its peripherally tetra substituted zinc phthalocyanine complex (TX-ZnPc) have been prepared and characterized by spectroscopic and elemental analysis techniques. Photoinitiated polymerization of methyl methacrylate (MMA) with TX-ZnPc has been investigated in the presence and absence of a co-initiator. Fluorescence and phosphorescence measurements have been also performed to determine the photophysical properties. Low fluorescence quantum yield (Φ{sub F}=0.08) compared to the unsubstituted ZnPc has been found. This allows initiator to undergo intersystem crossing into the triplet state and the lowest triplet state possesses π-π{sup ⁎} configuration. Highlights: ► Zinc phthalocyanine (ZnPc), peripherally functionalized with photoactive thioxanthone (TX) groups was synthesized. ► The photophysical and photochemical properties of resulting photoinitiator were studied in DMF. ► Photoinitiated polymerization of MMA with TX-ZnPc was investigated in the presence and absence of co-initiator.

Numerical study of the influence of ZnTe thickness on CdS/ZnTe solar cell performance

Science.gov (United States)

Skhouni, Othmane; El Manouni, Ahmed; Mari, Bernabe; Ullah, Hanif

2016-05-01

At present most of II-VI semiconductor based solar cells use the CdTe material as an absorber film. The simulation of its performance is realized by means of various numerical modelling programs. We have modelled a solar cell based on zinc telluride (ZnTe) thin film as absorber in substitution to the CdTe material, which contains the cadmium element known by its toxicity. The performance of such photovoltaic device has been numerically simulated and the thickness of the absorber layer has been optimized to give the optimal conversion efficiency. A photovoltaic device consisting of a ZnTe layer as absorber, CdS as the buffer layer and ZnO as a window layer was modelled through Solar Cell Capacitance Simulator Software. Dark and illuminated I-V characteristics and the results for different output parameters of ZnO/CdS/ZnTe solar cell were analyzed. The effect of ZnTe absorber thickness on different main working parameters such as: open-circuit voltage Voc, short-circuit current density Jsc, fill factor FF, photovoltaic conversion efficiency η was intensely studied in order to optimize ZnTe film thickness. This study reveals that increasing the thickness of ZnTe absorber layer results in higher efficiency until a maximum value and then decreases slightly. This maximum was found to be 10% at ZnTe optimum thickness close to 2 µm. Contribution to the topical issue "Materials for Energy Harvesting, Conversion and Storage (ICOME 2015) - Elected submissions", edited by Jean-Michel Nunzi, Rachid Bennacer and Mohammed El Ganaoui

Structural, magnetic and electrical properties of Zr-substitued NiZnCo ferrite nanopowders

Energy Technology Data Exchange (ETDEWEB)

Li, Le-Zhong, E-mail: lezhongli@cuit.edu.cn; Zhong, Xiao-Xi; Wang, Rui; Tu, Xiao-Qiang

2017-08-01

Highlights: • The static magnetic properties of NiZnCoZr ferrite nanopowders have been investigated. • The dielectric constant increases with the increase of Zr substitution. • The relaxation peak of tan δ ∼ T curves is observed for x ≥ 0.10. • Electrical transport behavior is found to follow the impurity semiconductor. • The dc resistivity increases at transition temperature with Zr substitution. - Abstract: Zr-substituted NiZnCo ferrite nanopowders, Ni{sub 0.4−x}Zn{sub 0.5}Zr{sub x}Co{sub 0.1}Fe{sub 2.0}O{sub 4} (0 ≤ x ≤ 0.20), were synthesized by the sol-gel auto-combustion method. The effects of Zr substitution on the structural, magnetic and electrical properties have been investigated. The DTA and TG results indicate that there are three steps of combustion process. The X-ray diffraction patterns show that the lattice parameter and the average crystallite size increase with the increase of Zr substitution. The saturation magnetization increases with the increase of Zr substitution when x ≤ 0.05, and then decreases when x > 0.05. Meanwhile, the coercivity initially decreases with the increase of Zr substitution when x ≤ 0.05, and then increases when x > 0.05. The polarization behavior for all the samples in the test frequency range from100 Hz to10 MHz obeys the charge polarization mechanism, which happens since the frequency of the hopping of electron exchange between Fe{sup 2+} and Fe{sup 3+} ions are far from the frequency of alternating-current field. And the dielectric constant increases with the increase of Zr substitution. The relaxation peak of the frequency dependence of dielectric loss is observed for x ≥ 0.10, which is due to the frequency of charge hopping between the Fe{sup 2+} and Fe{sup 3+} exactly matches with the frequency of the external applied field. Electrical transport behavior of the ferrite nanopowders is found to follow the impurity semiconductor, and the effect of Zr substitution on the temperature dependence

Absence of intrinsic ferromagnetism in Zn{sub 1-x}Mn{sub x}O alloys

Energy Technology Data Exchange (ETDEWEB)

Zhang Huawei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Shi Erwei [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Chen Zhizhan [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Liu Xuechao [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China); Xiao Bing [Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050 (China)

2006-10-04

Zn{sub 1-x}Mn{sub x}O alloys, with different Mn concentrations, were prepared by the hydrothermal method. X-ray diffraction and electron paramagnetic resonance spectra demonstrate that Zn{sup 2+} ions are homogeneously substituted by Mn{sup 2+} ions without changing the ZnO wurtzite structure. The x = 0.02 and 0.04 samples are paramagnetic. When the Mn concentrations are increased to x = 0.08 and 0.10, the samples exhibit some ferromagnetism due to a secondary phase (Zn,Mn)Mn{sub 2}O{sub 4}. (letter to the editor)

Manufacture of barium hexaferrite (BaO3.98Fe2O3) from iron oxide waste of grinding process by using calcination process

Science.gov (United States)

Idayanti, N.; Dedi; Kristiantoro, T.; Mulyadi, D.; Sudrajat, N.; Alam, G. F. N.

2018-03-01

The utilization of iron oxide waste of grinding process as raw materials for making barium hexaferrite has been completed by powder metallurgy method. The iron oxide waste was purified by roasting at 800 °C temperature for 3 hours. The method used varying calcination temperature at 1000, 1100, 1200, and 1250 °C for 3 hours. The starting iron oxide waste (Fe2O3) and barium carbonate (BaCO3) were prepared by mol ratio of Fe2O3:BaCO3 from the formula BaO3.98Fe2O3. Some additives such as calcium oxide (CaO), silicon dioxide (SiO2), and polyvinyl alcohol (PVA) were added after calcination process. The samples were formed at the pressure of 2 ton/cm2 and sintered at the temperature of 1250 °C for 1 hour. The formation of barium hexaferrite compounds after calcination is determined by X-Ray diffraction. The magnetic properties were observed by Permagraph-Magnet Physik with the optimum characteristic at calcination temperature of 1250 °C with the induction of remanence (Br) = 1.38 kG, coercivity (HcJ) = 4.533 kOe, product energy maximum (BHmax) = 1.086 MGOe, and density = 4.33 g/cm3.

Activation of a Cu/ZnO catalyst for methanol synthesis

DEFF Research Database (Denmark)

Andreasen, Jens Wenzel; Rasmussen, F.B.; Helveg, S.

2006-01-01

The structural changes during activation by temperature-programmed reduction of a Cu/ZnO catalyst for methanol synthesis have been studied by several in situ techniques. The catalyst is prepared by coprecipitation and contains 4.76 wt% Cu, which forms a substitutional solid solution with Zn......O as determined by resonant X-ray diffraction. In situ resonant X-ray diffraction reveals that the Cu atoms are extracted from the solid solution by the reduction procedure, forming metallic Cu crystallites. Cu is redispersed in bulk or surface Zn lattice sites upon oxidation by heating in air. The results...... is highly dispersed and in intimate contact with the surface of the host ZnO particles. The possibility of re-forming the (Zn,Cu)O solid solution by oxidation may provide a means of redispersing Cu in a deactivated catalyst....

Ostrich eggshell as calcium source for the synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc

Directory of Open Access Journals (Sweden)

J. R. M. Ferreira

Full Text Available Abstract In the present study, hydroxyapatite and Zn-substituted hydroxyapatite powders were synthesized using ostrich eggshell as a calcium source. The samples were analyzed by scanning electron microscopy with field emission gun, and X-ray diffraction (XRD to identify the present phases, and X-ray fluorescence spectroscopy for quantitative chemical analysis of the synthesized and heat treated powders. The Fourier transform infrared spectroscopy technique was used before and after heat treatments at 700, 900 and 1100 °C in order to identify the functional groups present, as an additional technique to the XRD analysis. The results presented in this study represent a promising method for synthesis of hydroxyapatite and hydroxyapatite partially substituted with zinc, since the results showed no undesirable phases or impurities in the produced powders. It was observed that Zn-substituted hydroxyapatite showed higher thermal stability, when compared to pure hydroxyapatite.

Electric field gradient calculation at atomic site of In implanted ZnO samples

International Nuclear Information System (INIS)

Abreu, Y.; Cruz, C. M.; Leyva, A.; Pinnera; Van Espen, P.; Perez, C.

2011-01-01

The electric field gradient (EFG) calculated for 111 In→ 111 Cd implanted ZnO samples is reported. The study was made for ideal hexagonal ZnO structures and super-cells considering the In implantation environment at the cation site using the 'WIEN2k' code within the GGA(+U) approximation. The obtained EFG values are in good agreement with the experimental reports for ideal ZnO and 111 In→ 111 Cd implanted structures; measured by perturbed angular correlation (PAC) and Moessbauer spectroscopy. The attribution of substitutional incorporation of 111 In at the ZnO cation site after annealing was confirmed. (Author)

Trivalent dopants on ZnO semiconductor obtained by mechanical milling

Energy Technology Data Exchange (ETDEWEB)

Damonte, L.C., E-mail: damonte@fisica.unlp.edu.a [Dto. De Fisica, UNLP, IFLP-CONICET, C.C.67 (1900) La Plata (Argentina); Dto. De Fisica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain); Donderis, V. [Dto. De Ingenieria Electrica, Universidad Politecnica de Valencia, Cami de Vera s/n, 46071 Valencia (Spain); Hernandez-Fenollosa, M.A. [Dto. De Fisica Aplicada, Universidad Politecnica de Valencia, Valencia (Spain)

2009-08-26

Al-doped ZnO powders were obtained by mechanical milling. This n-type oxide material is of interest for application in electronic devices as solar cells. The incorporation of the metal dopant into the ZnO wurtzite structure has been verified by X-ray diffraction, positron annihilation spectroscopy and optical analysis. The optical reflection measurements were strongly affected by the Al incorporation. The positron annihilation spectroscopy constituted an adequate probe to sense the cation substitution in the doped semiconductor.

Trivalent dopants on ZnO semiconductor obtained by mechanical milling

International Nuclear Information System (INIS)

Damonte, L.C.; Donderis, V.; Hernandez-Fenollosa, M.A.

2009-01-01

Al-doped ZnO powders were obtained by mechanical milling. This n-type oxide material is of interest for application in electronic devices as solar cells. The incorporation of the metal dopant into the ZnO wurtzite structure has been verified by X-ray diffraction, positron annihilation spectroscopy and optical analysis. The optical reflection measurements were strongly affected by the Al incorporation. The positron annihilation spectroscopy constituted an adequate probe to sense the cation substitution in the doped semiconductor.

Thermal expansion of Ti-substituted barium hexaferrite

NARCIS (Netherlands)

Hernandez-Gomez, P.; Francisco, de C.; Brabers, V.A.M.; Dalderop, J.H.J.

2000-01-01

Thermal expansion measurements in the range of 20–500 °C were carried out on both poly- and single crystalline samples of the hexagonal magnetoplumbite ferrite with composition BaTiFe11O19. The continuous scanning of the thermal expansion reveals the existence of a -type anomaly near the Curie

Hydrothermal growth of upright-standing ZnO sheet microcrystals

International Nuclear Information System (INIS)

Shi, Ruixia; Yang, Ping; Dong, Xiaobin; Jia, Changchao; Li, Jia

2014-01-01

Highlights: • Upright-standing ZnO sheet microcrystals were hydrothermally fabricated. • The ZnO sheets were prepared with sodium oxalate at 70 °C without any surfactant. • The preferable adsorption of oxalate anions causes the formation of ZnO sheet. • The continuous growth in six directions leads to the formation of hexagonal sheets. - Abstract: Large-scale upright-standing ZnO sheet microcrystals were fabricated on Zn substrate using sodium oxalate as structure-directing agent by a hydrothermal method at low temperature (70 °C) without any surfactant. The sheets are about 3–5 μm in dimension and 100–300 nm in thickness. The strong and narrow diffraction peaks of ZnO indicate that the sample has a good crystallinity and size. The morphology of sheet-like ZnO varied with the concentrations of sodium oxalate and reaction time. The sheet-like ZnO would transform into rod-like ones when sodium oxalate was substituted by equivalent sodium acetate. The formation of sheet-like ZnO is attributed to the preferable adsorption of oxalate anions on (0 0 0 1) face of ZnO, which inhibits the intrinsic growth of ZnO. Additionally, the continuous growth in six (0 1 −1 0) directions that have the lowest surface energy leads to the formation of hexagonal sheets

Impurity identification and characterization by electrical optical and nuclear methods. The ZnTe: Au case

International Nuclear Information System (INIS)

Magnea, N.; Pautrat, J.L.; Saminadayar, K.; Martin, P.; Bontemps, A.

1979-01-01

Gold is characterized in pure ZnTe by capacitance, luminescence and infra-red absorption experiments. The position of gold in the lattice is analysed by channeling of charged particles. We show that gold is principally introduced in substitutional position (Ausub(Zn)) and give a simple acceptor level at Esub(V) + 272 meV

Preparation and characterization of Ce-doped ZnO nanofibers by an electrospinning method

Directory of Open Access Journals (Sweden)

Jong-Pil Kim

2011-02-01

Full Text Available ZnO and Ce-doped ZnO Nanofibers on (111 Pt/SiO2/Si substrates were produced using an electrospinning technique. The as-prepared composite fibres were subjected to high-temperature calcination to produce inorganic fibers. After calcining at a temperature of 500 °C, the average diameter of the ZnO and Ce-doped ZnO nanofibers were determined to be 170 nm and 225 nm, respectively. The average grain size of the ZnO and Ce-doped ZnO nanofibers were about 50 nm and 57 nm, respectively. The microstructure, chemical bonding state and photoluminescence of the produced ZnO and Ce-doped ZnO nanofibers were investigated. The Ce-doped ZnO nanofiber can be assigned to the presence of Ce ions on substitutional sites of Zn ions and the Ce3+ state from X-ray photoelectron spectra. Compared with PL spectra of ZnO nanofibers, the peak position of the UV emission of the Ce-doped ZnO nanofibers is sharply suppressed while the green emission band is highly enhanced.

Proton irradiation induced defects in Cd and Zn doped InP

International Nuclear Information System (INIS)

Rybicki, G.C.; Williams, W.S.

1993-01-01

Proton irradiation induced defects in Zn and Cd doped InP have been studied by deep level transient spectroscopy, (DLTS). After 2 MeV proton irradiation the defects H4 and H5 were observed in lightly Zn doped InP, while the defects H3 and H5 were observed in more heavily Zn and Cd doped InP. The defect properties were not affected by the substitution of Cd for Zn, but the introduction rate of H5 was lower in Cd doped InP. The annealing rate of defects was also higher in Cd doped InP. The use of Cd doped InP may thus result in an InP solar cell with even greater radiation resistance

Room temperature ferromagnetism in Zn{sub 1-x}Co{sub x}S thin films with wurtzite structure

Energy Technology Data Exchange (ETDEWEB)

Patel, Shiv P., E-mail: shivpoojanbhola@gmail.com [Physics Department, University of Allahabad, Allahabad 211002 (India); Pivin, J.C. [CSNSM, IN2P3-CNRS, Batiment 108, F-91405 Orsay Campus (France); Chawla, A.K.; Chandra, Ramesh [Nanoscience Laboratory, IIC, Indian Institute of Technology, Roorkee 247667 (India); Kanjilal, D. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Kumar, Lokendra, E-mail: lkumarau@gmail.com [Physics Department, University of Allahabad, Allahabad 211002 (India)

2011-11-15

The magnetic properties of Zn{sub 1-x}Co{sub x}S (x=0.025 and 0.05) thin films grown on {alpha}-quartz substrates at different temperatures (T{sub S}) of 200, 400 and 600 deg. C by means of pulsed laser deposition are presented. The films are crystallized with wurtzite structure. Optical absorption and transmission electron microscopy measurements indicate that Co ions are substituted to Zn on tetrahedral sites. Their magnetic response is composed of ferromagnetic and paramagnetic components of which respective strengths depend on T{sub S} and Co concentration. This behavior is interpreted as due to fluctuations in the magnetic ordering, depending on grain size and site location in grain boundaries or in crystal cores. - Highlights: > Co doped ZnS thin films have been fabricated at different substrate temperatures. > Magnetization in the films changes with changing substrate temperature. > Substitution of Co on Zn sites gives room temperature intrinsic ferromagnetism. > Magnetization in the films is composed of ferromagnetic and paramagnetic components.

X-ray and magnetic studies of Zn substituted Ni–Pb ferrites

Indian Academy of Sciences (India)

Unknown

nic applications such as transformers, choke coils, noise filters, recording heads etc. Nickel ferrites and Zn2+ sub- stituted nickel-ferrites are widely used in electronics and electrical industries as they exhibit interesting variations in the electrical and magnetic properties. Electrical and magnetic properties are influenced by ...

Synthesis and characterization of biocompatible hydroxyapatite ...

Indian Academy of Sciences (India)

https://www.ias.ac.in/article/fulltext/boms/026/07/0655-0660. Keywords. Bioceramics; hyperthermia; ferrite; biocompatible coating. Abstract. Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own ...

Coordination geometries of Zn(II) and Cd(II) in phosphotriesterase: Influence of water molecules in the active site

DEFF Research Database (Denmark)

Krauss, M; Olsen, Lars; Antony, J

2002-01-01

Models of the metal ion binding sites of native ZnZn and of cadmium-substituted ZnCd and CdCd phosphotriesterase, including full amino acid side chains, were geometry optimized with quantum mechanical methods, with effective fragment potentials (EFP) representing the protein environment surroundi...... to the Od1 of the carboxylate of the first-shell aspartate designated M 1, but the energy difference between Cd1Zn2 and the lowest energy Zn1Cd2 structure is only about 2 kcal/mol and decreasing with the addition of water molecules. The Zn1Cd2 arrangement is found experimentally....

Explanation of ferromagnetism origin in C-doped ZnO by first principle calculations

International Nuclear Information System (INIS)

El Amiri, A.; Lassri, H.; Hlil, E.K.; Abid, M.

2015-01-01

By ab-initio calculations, we systematically study possible source of ferromagnetism C-doped ZnO compound. The electronic structure and magnetic properties of C-doped ZnO with / without ZnO host and C defects were investigated using the Korringa–Kohn–Rostoker (KKR) method combined with coherent potential approximation (CPA). We show that Zn vacancy and presence of C defects (substitutional, interstitial or combination of both) induce the ferromagnetism in C-doped ZnO. From density of state (DOS) analysis, we show that p–p interaction between C atoms and/or C and O atoms is the mechanism of ferromagnetic coupling in C-doped ZnO. - Highlights: • We study the effect of ZnO host and C defects on ferromagnetism in C-doped ZnO. • Details of KKR method calculations performed to investigate both magnetic and electronic structures. • Magnetic moments, total and partial DOS for C-doped ZnO are well calculated and discussed. • Based on DOS calculations we interpret a origin of ferromagnetism in C-doped ZnO. • Mechanism of ferromagnetic coupling is well proposed

Explanation of ferromagnetism origin in C-doped ZnO by first principle calculations

Energy Technology Data Exchange (ETDEWEB)

El Amiri, A., E-mail: aelamiri@casablanca.ma [Laboratoire de Physique Fondamentale et Appliquée (LPFA), Faculté des Sciences Ain Chock, Université Hassan II, B.P. 5366 Mâarif, Casablanca, Maroc (Morocco); Lassri, H. [Laboratoire de Physique des Matériaux, Micro-électronique, Automatique et Thermique (LPMMAT). Faculté des Sciences Ain Chock, Université Hassan II, B.P. 5366 Mâarif, Casablanca, Maroc (Morocco); Hlil, E.K. [Institut Néel, CNRS et Université Joseph Fourier, BP 166, 38042 Grenoble (France); Abid, M. [Laboratoire de Physique Fondamentale et Appliquée (LPFA), Faculté des Sciences Ain Chock, Université Hassan II, B.P. 5366 Mâarif, Casablanca, Maroc (Morocco)

2015-01-15

By ab-initio calculations, we systematically study possible source of ferromagnetism C-doped ZnO compound. The electronic structure and magnetic properties of C-doped ZnO with / without ZnO host and C defects were investigated using the Korringa–Kohn–Rostoker (KKR) method combined with coherent potential approximation (CPA). We show that Zn vacancy and presence of C defects (substitutional, interstitial or combination of both) induce the ferromagnetism in C-doped ZnO. From density of state (DOS) analysis, we show that p–p interaction between C atoms and/or C and O atoms is the mechanism of ferromagnetic coupling in C-doped ZnO. - Highlights: • We study the effect of ZnO host and C defects on ferromagnetism in C-doped ZnO. • Details of KKR method calculations performed to investigate both magnetic and electronic structures. • Magnetic moments, total and partial DOS for C-doped ZnO are well calculated and discussed. • Based on DOS calculations we interpret a origin of ferromagnetism in C-doped ZnO. • Mechanism of ferromagnetic coupling is well proposed.

ZnO:Ca nanopowders with enhanced CO2 sensing properties

International Nuclear Information System (INIS)

Dhahri, R; Hjiri, M; El Mir, L; Fazio, E; Neri, F; Barreca, F; Donato, N; Bonavita, A; Leonardi, S G; Neri, G

2015-01-01

Calcium doped ZnO (CZO) nanopowders with [Ca]/[Zn] atomic ratios of 0, 0.01, 0.03 and 0.05 were prepared via a sol-gel route and characterized by scanning electron microscopy, transmission electron microscopy, x-ray diffraction and Fourier transform infrared spectroscopy (FT-IR). Characterization data showed that undoped and Ca-doped ZnO samples have a hexagonal wurtzite structure with a slight distortion of the ZnO lattice and no extra secondary phases, suggesting the substitution of Ca ions in the ZnO structure.Chemo-resistive devices based on a thick layer of the synthesized CZO nanoparticles were fabricated and their electrical and sensing properties towards CO 2 were investigated. Sensing tests have demonstrated that Ca loading is the key factor in modulating the electrical properties and strongly improving the response of ZnO matrix towards CO 2 . An increased CO 2 adsorption with Ca loading has been also evidenced by FT-IR, providing the basis for the formulation of a plausible mechanism for CO 2 sensing operating on these sensors. (paper)

Electronic structure and p-type doping of ZnSnN2

Science.gov (United States)

Wang, Tianshi; Janotti, Anderson; Ni, Chaoying

ZnSnN2 is a promising solar-cell absorber material composed of earth abundant elements. Little is known about doping, defects, and how the valence and conduction bands in this material align with the bands in other semiconductors. Using density functional theory with the the Heyd-Scuseria-Ernzerhof hybrid functional (HSE06), we investigate the electronic structure of ZnSnN2, its band alignment to other semiconductors, such as GaN and ZnO, the possibility of p-type doping, and the possible causes of the observed unintentional n-type conductivity. We find that the position of the valence-band maximum of ZnSnN2 is 0.55 eV higher than that of GaN, yet the conduction-band minimum is close to that in ZnO. As possible p-type dopants, we explore Li, Na, and K substituting on the Zn site. Finally, we discuss the cause of unintentional n-type conductivity by analyzing the position of the conduction-band minimum with respect to that of GaN and ZnO.

Structural and dielectric properties of Zr and Cu co-substituted Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Jalaiah, K., E-mail: kjalu4u@gmail.com [Department of Physics, Andhra University, Visakhapatnam 530 003 (India); Chandra mouli, K. [Department of Engineering Physics, Andhra University, Visakhapatnam 530 003 (India); Subba Rao, P.S.V. [Department of Physics, Andhra University, Visakhapatnam 530 003 (India); Sreedhar, B. [IICT, Hyderabad (India)

2017-06-15

Highlights: • The porosity was increased with increasing dopant concentration of Zr and Cu from the 10.57% to 20.11%. • The force constant and wave numbers in octahedral and tetrahedral site is increased with increasing the dopant concentration of Zr and Cu. • The compositional dielectric constant at 100 kHz is increased from the 9.85 to 86.53, with increasing dopant concentration of Zr and Cu. - Abstract: Zr and Cu Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2}O{sub 4} ferrites have been prepared by the sol-gel auto combustion method using the nitrates. The ethylene glycol and citric acid were mixed as the combustion agents. The synthesized powders were calcinate at 800 °C for 3 h and they are pressed in desired shaped and sintered at 1200 °C for 2 h in air atmosphere. The X-ray diffraction analysis confirms the single phase cubic spinel structure. The SEM pictures revels that the substitution of higher valence ions results fine grained intragranular pore free microstructure. The dielectric properties of substituted ferrites exhibits decreasing trend at lower frequencies up to 1000 Hz beyond which it should in stable response. All the results are explained in terms of compositional and frequency variation.

Transition from diamagnetic to ferromagnetic state in laser ablated nitrogen doped ZnO thin films

Directory of Open Access Journals (Sweden)

Kajal Jindal

2015-02-01

Full Text Available Transition from room temperature diamagnetic to ferromagnetic state in N doped ZnO (ZnO:N films grown by pulsed laser deposition with tunable energy density has been identified. ZnO:N films deposited with moderate laser energy density of 2.5 J/cm2 are single phase and nearly defect free having N dopant substitution at O sites in ZnO lattice, exhibiting intrinsic ferromagnetism. When energy density reduces (<2.5 J/cm2, defects in ZnO:N film degrades ferromagnetism and exhibit diamagnetic phase when grown at energy density of 1.0 J/cm2. Growth kinetics, which in turn depends on laser energy density is playing important role in making transition from ferromagnetic to diamagnetic in ZnO:N films.

ZnO thin films and nanostructures for emerging optoelectronic applications

Science.gov (United States)

Rogers, D. J.; Teherani, F. H.; Sandana, V. E.; Razeghi, M.

2010-02-01

ZnO-based thin films and nanostructures grown by PLD for various emerging optoelectronic applications. AZO thin films are currently displacing ITO for many TCO applications due to recent improvements in attainable AZO conductivity combined with processing, cost and toxicity advantages. Advances in the channel mobilities and Id on/off ratios in ZnO-based TTFTs have opened up the potential for use as a replacement for a-Si in AM-OLED and AM-LCD screens. Angular-dependent specular reflection measurements of self-forming, moth-eye-like, nanostructure arrays grown by PLD were seen to have green gap in InGaN-based LEDs was combated by substituting low Ts PLD n-ZnO for MOCVD n-GaN in inverted hybrid heterojunctions. This approach maintained the integrity of the InGaN MQWs and gave LEDs with green emission at just over 510 nm. Hybrid n-ZnO/p-GaN heterojunctions were also seen to have the potential for UV (375 nm) EL, characteristic of ZnO NBE emission. This suggests that there was significant hole injection into the ZnO and that such LEDs could profit from the relatively high exciton binding energy of ZnO.

Synthesis and characterization of Mg-doped ZnO hollow spheres

International Nuclear Information System (INIS)

Hammad, Talaat M.; Salem, Jamil K.

2011-01-01

Mg-doped ZnO nanoparticles were synthesized by a simple chemical method at low temperature with Mg:Zn atomic ratio from 0 to 7%. The synthesis process is based on the hydrolysis of zinc acetate dihydrate and magnesium acetate tetrahydrate were heated under refluxing at 65 °C using methanol as a solvent. X-ray diffraction analysis reveals that the Mg-doped ZnO crystallizes in a wurtzite structure with crystal size of 5–12 nm. These nanocrystals self-aggregated themselves into hollow spheres of size of 800–1100 nm. High resolution transmission electron microscopy images show that each sphere is made up of numerous nanoparticles of average diameter 5–11 nm. The XRD patterns, SEM and TEM micrographs of doping of Mg in ZnO confirmed the formation of hollow spheres indicating that the Mg 2+ is successfully substituted into the ZnO host structure of the Zn 2+ site. Furthermore, the UV–Vis spectra and photoluminescence (PL) spectra of the ZnO nanoparticles were also investigated. The band gap of the nanoparticles can be tuned in the range of 3.36–3.55 eV by the use of the dopants.

Charge transfer-type fluorescence of Ti-doped Ca{sub 14}Al{sub 10}Zn{sub 6}O{sub 35}

Energy Technology Data Exchange (ETDEWEB)

Satoh, Yuta; Takemoto, Minoru, E-mail: takemoto@chem.kanagawa-it.ac.jp

2017-05-15

The calcium aluminum zincates Ca{sub 14}(Al{sub 1-2x}Ti{sub x}Zn{sub x}){sub 10}Zn{sub 6}O{sub 35}, in which Al{sup 3+} sites in the host material Ca{sub 14}Al{sub 10}Zn{sub 6}O{sub 35} are simultaneously substituted by Ti{sup 4+} and Zn{sup 2+}, were synthesized by a polymerized complex method. Al{sup 3+} ions could be replaced up to an x value of 0.1. The host material does not exhibit fluorescence, while the cation-substituted samples show an emission band centered at 383 nm under excitation by UV light at 243 nm. The emission intensity increases with x up to 0.1 and then gradually decreases as x is further increased. The emission wavelength also becomes longer with increasing temperature. Based on the properties of other Ti{sup 4+}-containing fluorescent materials, the emission of Ca{sub 14}(Al{sub 1-2x}Ti{sub x}Zn{sub x}){sub 10}Zn{sub 6}O{sub 35} is attributed to charge transfer-type fluorescence resulting from [TiO{sub 6}] octahedra.

Magnetic exchange interactions in Mn doped ZnSnAs{sub 2} chalcopyrite

Energy Technology Data Exchange (ETDEWEB)

Bouhani-Benziane, H.; Sahnoun, O. [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Sahnoun, M., E-mail: sahnoun_cum@yahoo.fr [Laboratoire de Physique Quantique de la Matière et Modélisation Mathématique (LPQ3M), University of Mascara (Algeria); Department of Chemistry, University of Fribourg (Switzerland); Driz, M. [Laboratoire de Sciences des Matériaux (LSM), University of Sidi Bel Abbes (Algeria); Daul, C. [Department of Chemistry, University of Fribourg (Switzerland)

2015-12-15

Accurate ab initio full-potential augmented plane wave (FP-LAPW) electronic calculations within generalized gradient approximation have been performed for Mn doped ZnSnAs{sub 2} chalcopyrites, focusing on their electronic and magnetic properties as a function of the geometry related to low Mn-impurity concentration and the spin magnetic alignment (i.e., ferromagnetic vs antiferromagnetic). As expected, Mn is found to be a source of holes and localized magnetic moments of about 4 µ{sub B} per Mn atom are calculated which are sufficiently large. The defect calculations are firstly performed by replacing a single cation (namely Zn and Sn) with a single Mn atom in the pure chalcopyrite ZnSnAs{sub 2} supercell, and their corresponding formation energies show that the substitution of a Sn atom (rather than Zn) by Mn is strongly favored. Thereafter, a comparison of total energy differences between ferromagnetic (FM) and antiferromagnetic (AFM) are given. Surprisingly, the exchange interaction between a Mn pairs is found to oscillate with the distance between them. Consequently, the AFM alignment is energetically favored in Mn-doped ZnSnAs{sub 2} compounds, except for low impurity concentration associated with lower distances between neighboring Mn impurities, in this case the stabilization of FM increases. Moreover, the ferromagnetic alignment in the Mn-doped ZnSnAs{sub 2} systems behaves half-metallic; the valence band for majority spin orientation is partially filled while there is a gap in the density of states for the minority spin orientation. This semiconducting gap of ~1 eV opened up in the minority channel and is due to the large bonding–antibonding splitting from the p–d hybridization. Our findings suggest that the Mn-doped ZnSnAs{sub 2} chalcopyrites could be a different class of ferromagnetic semiconductors. - Highlights: • ab initio calculations were performed on Mn doped ZnSnAs{sub 2} chalcopyrite. • Substitution of a Sn atom (rather than Zn) by Mn

Performance improvement for solution-processed high-mobility ZnO thin-film transistors

International Nuclear Information System (INIS)

Li Chensha; Loutfy, Rafik O; Li Yuning; Wu Yiliang; Ong, Beng S

2008-01-01

The fabrication technology of stable, non-toxic, transparent, high performance zinc oxide (ZnO) thin-film semiconductors via the solution process was investigated. Two methods, which were, respectively, annealing a spin-coated precursor solution and annealing a drop-coated precursor solution, were compared. The prepared ZnO thin-film semiconductor transistors have well-controlled, preferential crystal orientation and exhibit superior field-effect performance characteristics. But the ZnO thin-film transistor (TFT) fabricated by annealing a drop-coated precursor solution has a distinctly elevated linear mobility, which further approaches the saturated mobility, compared with that fabricated by annealing a spin-coated precursor solution. The performance of the solution-processed ZnO TFT was further improved when substituting the spin-coating process by the drop-coating process

Performance improvement for solution-processed high-mobility ZnO thin-film transistors

Energy Technology Data Exchange (ETDEWEB)

Li Chensha; Loutfy, Rafik O [Department of Chemical Engineering, McMaster University, 1280 Main Street West, Hamilton, Ontario L8S 4L7 (Canada); Li Yuning; Wu Yiliang; Ong, Beng S [Materials Design and Integration Laboratory, Xerox Research Centre of Canada, 2660 Speakman Drive, Mississauga, Ontario L5K 2L1 (Canada)], E-mail: lichnsa@163.com

2008-06-21

The fabrication technology of stable, non-toxic, transparent, high performance zinc oxide (ZnO) thin-film semiconductors via the solution process was investigated. Two methods, which were, respectively, annealing a spin-coated precursor solution and annealing a drop-coated precursor solution, were compared. The prepared ZnO thin-film semiconductor transistors have well-controlled, preferential crystal orientation and exhibit superior field-effect performance characteristics. But the ZnO thin-film transistor (TFT) fabricated by annealing a drop-coated precursor solution has a distinctly elevated linear mobility, which further approaches the saturated mobility, compared with that fabricated by annealing a spin-coated precursor solution. The performance of the solution-processed ZnO TFT was further improved when substituting the spin-coating process by the drop-coating process.

Suppression of Na interstitials in Na-F codoped ZnO

Science.gov (United States)

Huo, Wenxing; Mei, Zengxia; Tang, Aihua; Liang, Huili; Du, Xiaolong

2018-04-01

Controlling the formation of interstitial Na (Nai) self-compensating defects has been a long-term physics problem for effective Na doping in ZnO. Herein, we present an experimental approach to the suppression of Nai defects in ZnO via Na and F codoping under an oxygen-rich condition during the molecular beam epitaxy growth process. It is found that the incorporation of such large numbers of Na and F dopants (˜1020 cm-3) does not cause an obvious influence on the lattice parameters. Hall-effect measurements demonstrate that F doping efficiently raises the Fermi level (EF) of ZnO films, which is expected to make the formation energy of Nai and NaZn increase and decrease, respectively. Most of the Na atoms occupy the substitutional Zn sites, and the formation of Nai is suppressed consequently. Secondary ion mass spectrometry measurements reveal that F and Na atoms are tightly bonded together due to their strong Coulomb interaction. The enhanced deep level emission (DLE) in ZnO:Na-F is ascribed to the considerable amount of isolated Zn vacancy (VZn) defects induced by the elevated EF and the formation of neutral (" separators="| FO + - Na Zn - ) 0 complexes. On the other hand, formation of (" separators="| FO + - VZn 2 - ) - complexes in ZnO:F exhausts most of the isolated Zn vacancies, leading to the disappearance of the DLE band.

Effects of Surface Morphology ZnAl2O4 of Ceramic Materials on Osteoblastic Cells Responses

International Nuclear Information System (INIS)

Suarez-Franco, J.L.; Fernandez-Pedrero, J.A.; Ivarez-Perez, M.A.; Garcia-Hipolito, M.; Surarez-Rosales, M.; Fregoso, O.; Juarez-Islas, J.A.; Ivarez-Perez, M.A.

2013-01-01

Ceramic scaffolds are widely studied in the tissue engineering field due to their potential in medical applications as bone substitutes or as bone-filling materials. The purpose of this study was to investigate the effect of surface morphology of nano structure thin films of ZnAl 2 O 4 prepared by spray pyrolysis and bulk pellets of polycrystalline ZnAl 2 O 4 prepared by chemical coprecipitation reaction on the in vitro cell adhesion, viability, and cell-material interactions of osteoblastic cells. Our result showed that cell attachment was significantly enhanced from 60 to 80% on the ZnAl 2 O 4 nano structured material surface when compared with bulk ceramic surfaces. Moreover, our results showed that the balance of morphological properties of the thin film nano structure ceramic improves cell-material interaction with enhanced spreading and filopodia with multiple cellular extensions on the surface of the ceramic and enhancing cell viability/proliferation in comparison with bulk ceramic surfaces used as control. Altogether, these results suggest that zinc aluminate nano structured materials have a great potential to be used in dental implant and bone substitute applications.Ceramic scaffolds are widely studied in the tissue engineering field due to their potential in medical applications as bone substitutes or as bone-filling materials. The purpose of this study was to investigate the effect of surface morphology of nano structure thin films of ZnAl 2 O 4 prepared by spray pyrolysis and bulk pellets of polycrystalline ZnAl 2 O 4 prepared by chemical coprecipitation reaction on the in vitro cell adhesion, viability, and cell-material interactions of osteoblastic cells. Our result showed that cell attachment was significantly enhanced from 60 to 80% on the ZnAl 2 O 4 nano structured material surface when compared with bulk ceramic surfaces. Moreover, our results showed that the balance of morphological properties of the thin film nano structure ceramic improves

Enhanced ultraviolet photo-response in Dy doped ZnO thin film

Science.gov (United States)

Kumar, Pawan; Singh, Ranveer; Pandey, Praveen C.

2018-02-01

In the present work, a Dy doped ZnO thin film deposited by the spin coating method has been studied for its potential application in a ZnO based UV detector. The investigations on the structural property and surface morphology of the thin film ensure that the prepared samples are crystalline and exhibit a hexagonal crystal structure of ZnO. A small change in crystallite size has been observed due to Dy doping in ZnO. AFM analysis ascertains the grain growth and smooth surface of the thin films. The Dy doped ZnO thin film exhibits a significant enhancement in UV region absorption as compared to the pure ZnO thin film, which suggests that Dy doped ZnO can be used as a UV detector. Under UV irradiation of wavelength 325 nm, the photocurrent value of Dy doped ZnO is 105.54 μA at 4.5 V, which is 31 times greater than that of the un-doped ZnO thin film (3.39 μA). The calculated value of responsivity is found to increase significantly due to the incorporation of Dy in the ZnO lattice. The observed higher value of photocurrent and responsivity could be attributed to the substitution of Dy in the ZnO lattice, which enhances the conductivity, electron mobility, and defects in ZnO and benefits the UV sensing property.

Effect of cobalt doping on the mechanical properties of ZnO nanowires

Energy Technology Data Exchange (ETDEWEB)

Vahtrus, Mikk; Šutka, Andris [Institute of Physics, University of Tartu, W. Ostwaldi 1, 50412 Tartu (Estonia); Polyakov, Boris [Institute of Solid State Physics, University of Latvia, Kengaraga 8, LV-1063 Riga (Latvia); Oras, Sven; Antsov, Mikk [Institute of Physics, University of Tartu, W. Ostwaldi 1, 50412 Tartu (Estonia); Doebelin, Nicola [RMS Foundation, Bischmattstrasse 12, Bettlach 2544 (Switzerland); Institute of Geological Sciences, University of Bern, Baltzerstrasse 1–3, Bern 3012 (Switzerland); Lõhmus, Rünno; Nõmmiste, Ergo [Institute of Physics, University of Tartu, W. Ostwaldi 1, 50412 Tartu (Estonia); Vlassov, Sergei, E-mail: vlassovs@ut.ee [Institute of Physics, University of Tartu, W. Ostwaldi 1, 50412 Tartu (Estonia)

2016-11-15

In this work, we investigate the influence of doping on the mechanical properties of ZnO nanowires (NWs) by comparing the mechanical properties of pure and Co-doped ZnO NWs grown in similar conditions and having the same crystallographic orientation [0001]. The mechanical characterization included three-point bending tests made with atomic force microscopy and cantilever beam bending tests performed inside scanning electron microscopy. It was found that the Young's modulus of ZnO NWs containing 5% of Co was approximately a third lower than that of the pure ZnO NWs. Bending strength values were comparable for both materials and in both cases were close to theoretical strength indicating high quality of NWs. Dependence of mechanical properties on NW diameter was found for both doped and undoped ZnO NWs. - Highlights: •Effect of Co doping on the mechanical properties of ZnO nanowires is studied. •Co substitutes Zn atoms in ZnO crystal lattice. •Co addition affects crystal lattice parameters. •Co addition results in significantly decreased Young's modulus of ZnO. •Bending strength for doped and undoped wires is close to the theoretical strength.

Local fields in Co and Mn Co-doped ZnO

Energy Technology Data Exchange (ETDEWEB)

Sato, W., E-mail: wsato@se.kanazawa-u.ac.jp [Kanazawa University, Institute of Science and Engineering (Japan); Kano, Y.; Suzuki, T.; Nakagawa, M. [Kanazawa University, Graduate School of Natural Science and Technology (Japan); Kobayashi, Y. [The University of Electro-Communications, Department of Engineering Science (Japan)

2016-12-15

The magnetic properties of ZnO co-doped with 5 at. % Co and 5 at. % Mn(Zn{sub 0.90}Co{sub 0.05}Mn{sub 0.05}O) synthesized by a solid-state reaction were investigated by means of {sup 57}Co emission Mössbauer spectroscopy. The majority of the probe ions (80 %) residing in defect-free substitutional Zn sites take the oxidation state of {sup 57}Fe {sup 2+}, and the others presumably form local defects taking the state of {sup 57}Fe {sup 3+} at room temperature. Both components show doublets, and RT ferromagnetism was thus absent in the sample. For the measurement at 10 K, spectral broadening was observed, implying a possible presence of a weak magnetic component.

Dopants incorporation in ZnO mechanical milled powders sensed by positrons

International Nuclear Information System (INIS)

Damonte, L. C.; Donderis, V.; Hernandez Fenollosa, M. A.

2007-01-01

M-doped ZnO (M: Cd, Mg) powders obtained by mechanical milling were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and positron lifetime annihilation spectroscopy (PALS). The mixing of the oxides is followed by means of XRD and SEM. As milling proceeds, a clear reduction of grain size and homogenization are observed. The evolution of annihilation parameters with milling time and cation content were analyzed and related with the kind of mechanical induced defect involved. Ternary oxides Zn 1-x M x O were efficiency obtained for certain compositions. The results showed that positrons constitute a well suited probe to characterize the cation substitution in the ZnO oxide lattice.

Dopants incorporation in ZnO mechanical milled powders sensed by positrons

Energy Technology Data Exchange (ETDEWEB)

Damonte, L. C., E-mail: damonte@fisica.unlp.edu.ar; Donderis, V.; Hernandez Fenollosa, M. A. [Universidad Politecnica de Valencia, Departamento de Fisica Aplicada (Spain)

2007-09-15

M-doped ZnO (M: Cd, Mg) powders obtained by mechanical milling were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and positron lifetime annihilation spectroscopy (PALS). The mixing of the oxides is followed by means of XRD and SEM. As milling proceeds, a clear reduction of grain size and homogenization are observed. The evolution of annihilation parameters with milling time and cation content were analyzed and related with the kind of mechanical induced defect involved. Ternary oxides Zn{sub 1-x}M{sub x}O were efficiency obtained for certain compositions. The results showed that positrons constitute a well suited probe to characterize the cation substitution in the ZnO oxide lattice.

Enhanced persistent red luminescence in Mn2+-doped (Mg,Zn)GeO3 by electron trap and conduction band engineering

Science.gov (United States)

Katayama, Yumiko; Kayumi, Tomohiro; Ueda, Jumpei; Tanabe, Setsuhisa

2018-05-01

The effect of Zn substitution on the persistent luminescence properties of MgGeO3:Mn2+-Ln3+ (Ln = Eu and Yb) red phosphors was investigated. The intensity of the persistent luminescence of the Eu3+ co-doped phosphors increased with increasing Zn content, whereas that of the Yb3+ co-doped samples decreased. For both series of lanthanide co-doped samples, the thermoluminescence (TL) glow peak shifted to the lower temperature side with increasing Zn content. These persistent luminescence properties were well explained in terms of lowering of the bottom of the conduction band relative to the ground state of the divalent lanthanide ions. Especially, in Eu3+ co-doped system, TL peak shifted from 520 K to 318 K by 50% Zn substitution. The persistent radiance of the (Mg0.5 Zn0.5)GeO3: Mn2+-Eu3+ sample at 1 h after ceasing UV light was 46 times stronger than that of MgGeO3:Mn2+-Eu3+, and 11 times stronger than that of ZnGa2O4: Cr3+ standard deep red persistent phosphor.

The Effect of (Ag, Ni, Zn)-Addition on the Thermoelectric Properties of Copper Aluminate

DEFF Research Database (Denmark)

Yanagiya, Shun-ichi; Van Nong, Ngo; Xu, Jianxiao Jackie

2010-01-01

Polycrystalline bulk copper aluminate Cu1-x-yAgxByAlO2 with B = Ni or Zn were prepared by spark plasma sintering and subsequent thermal treatment. The influence of partial substitution of Ag, Ni and Zn for Cu-sites in CuAlO2 on the high temperature thermoelectric properties has been studied......, indicating a significant improvement compared with the non-doped CuAlO2 sample...

Deposition of magnetoelectric hexaferrite thin films on substrates of silicon

Energy Technology Data Exchange (ETDEWEB)

Zare, Saba; Izadkhah, Hessam; Vittoria, Carmine

2016-12-15

Magnetoelectric M-type hexaferrite thin films (SrCo{sub 2}Ti{sub 2}Fe{sub 8}O{sub 19}) were deposited using Pulsed Laser Deposition (PLD) technique on Silicon substrate. A conductive oxide layer of Indium-Tin Oxide (ITO) was deposited as a buffer layer with the dual purposes of 1) to reduce lattice mismatch between the film and silicon and 2) to lower applied voltages to observe magnetoelectric effects at room temperature on Silicon based devices. The film exhibited magnetoelectric effects as confirmed by vibrating sample magnetometer (VSM) techniques in voltages as low as 0.5 V. Without the oxide conductive layer the required voltages to observe magnetoelectric effects was typically about 1000 times larger. The magnetoelectric thin films were characterized by X-ray diffractometer, scanning electron microscope, energy-dispersive spectroscopy, vibrating sample magnetometer, and ferromagnetic resonance techniques. We measured saturation magnetization of 650 G, and coercive field of about 150 Oe for these thin films. The change in remanence magnetization was measured in the presence of DC voltages and the changes in remanence were in the order of 15% with the application of only 0.5 V (DC voltage). We deduced a magnetoelectric coupling, α, of 1.36×10{sup −9} s m{sup −1} in SrCo{sub 2}Ti{sub 2}Fe{sub 8}O{sub 19} thin films.

3d-metal doping (Fe,Co,Ni,Zn) of the high Tc perovskite YBa2Cu3O(7-y)

International Nuclear Information System (INIS)

Tarascon, J.M.; Barboux, P.; Greene, L.H.; Hull, G.W.; Bagley, B.G.

1988-01-01

The structural, magnetic and superconducting properties of the mixed compounds YBa 2 Cu(3-x)M(x)O(7-y) (M = Ni,Zn,Fe, and Co) are reported. Values of y, determined by titration, are found to be dependent on the nature and amount of the doping. The range of solubility is greater for the Fe and Co compounds (x = 1) than for those with Ni or Zn (x = 0.3). The undoped material is orthorhombic and remains orthorhombic after substitution for Cu by Ni or Zn, whereas a tetragonal phase is observed when Fe, Co are substituted for Cu. DC resistance and AC susceptibility measurements show that Tc is depressed from 90K (x = 0) to 45K (x = 0.2) for both the Ni- and Zn-doped compounds, and Tc is destroyed in the Fe- and Co-doped compounds when x reaches 0.4. It is suggested that a valence of two be assigned to the Ni and Zn and three to the Fe and Co ions. 8 references

The crystallization and physical properties of Al-doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Chen, K.J. [Institute of Microelectronics and Department of Electrical Engineering, Center for Micro/Nano Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan (China); Fang, T.H. [Institute of Mechanical and Electromechanical Engineering, National Formosa University, Yunlin 632, Taiwan (China); Hung, F.Y. [Institute of Nanotechnology and Microsystems Engineering, Center for Micro/Nano Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan (China)], E-mail: fyhung@mail.mse.ncku.edu.tw; Ji, L.W. [Institute of Mechanical and Electromechanical Engineering, National Formosa University, Yunlin 632, Taiwan (China); Chang, S.J.; Young, S.J. [Institute of Microelectronics and Department of Electrical Engineering, Center for Micro/Nano Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan (China); Hsiao, Y.J. [Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan (China)

2008-07-15

Un-doped Al (0-9 at.%) nanoparticles and doped ZnO powders were prepared by the sol-gel method. The nanoparticles were heated at 700-800 deg. C for 1 h in air and then analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectra and photoluminescence (PL). The results of un-doped (ZnO) and Al-doped ZnO (AZO) nanoparticles were also compared to investigate the structural characteristics and physical properties. XRD patterns of AZO powders were similar to those of ZnO powders, indicating that micro-Al ions were substituted for Zn atoms and there were no variations in the structure of the ZnO nanoparticles. From the XRD and SEM data, the grain size of the AZO nanoparticles increased from 34.41 to 40.14 nm when the annealing temperature was increased. The Raman intensity of the AZO nanoparticles (Al = 5 at.%) increased when the annealing temperature was increased. Increasing the degree of crystalline not only reduced the residual stress, but also improved the physical properties of the nanoparticles.

The crystallization and physical properties of Al-doped ZnO nanoparticles

International Nuclear Information System (INIS)

Chen, K.J.; Fang, T.H.; Hung, F.Y.; Ji, L.W.; Chang, S.J.; Young, S.J.; Hsiao, Y.J.

2008-01-01

Un-doped Al (0-9 at.%) nanoparticles and doped ZnO powders were prepared by the sol-gel method. The nanoparticles were heated at 700-800 deg. C for 1 h in air and then analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman spectra and photoluminescence (PL). The results of un-doped (ZnO) and Al-doped ZnO (AZO) nanoparticles were also compared to investigate the structural characteristics and physical properties. XRD patterns of AZO powders were similar to those of ZnO powders, indicating that micro-Al ions were substituted for Zn atoms and there were no variations in the structure of the ZnO nanoparticles. From the XRD and SEM data, the grain size of the AZO nanoparticles increased from 34.41 to 40.14 nm when the annealing temperature was increased. The Raman intensity of the AZO nanoparticles (Al = 5 at.%) increased when the annealing temperature was increased. Increasing the degree of crystalline not only reduced the residual stress, but also improved the physical properties of the nanoparticles

ZnO-Based Transparent Conductive Thin Films: Doping, Performance, and Processing

International Nuclear Information System (INIS)

Liu, Y.; Li, Y.; Zeng, H.

2013-01-01

ZnO-based transparent conductive thin films have attracted much attention as a promising substitute material to the currently used indium-tin-oxide thin films in transparent electrode applications. However, the detailed function of the dopants, acting on the electrical and optical properties of ZnO-based transparent conductive thin films, is not clear yet, which has limited the development and practical applications of ZnO transparent conductive thin films. Growth conditions such as substrate type, growth temperature, and ambient atmosphere all play important roles in structural, electrical, and optical properties of films. This paper takes a panoramic view on properties of ZnO thin films and reviews the very recent works on new, efficient, low-temperature, and high-speed deposition technologies. In addition, we highlighted the methods of producing ZnO-based transparent conductive film on flexible substrate, one of the most promising and rapidly emerging research areas. As optimum-processing-parameter conditions are being obtained and their influencing mechanism is becoming clear, we can see that there will be a promising future for ZnO-based transparent conductive films.

Investigation of interaction between alkoxy substituted phthalocyanines with different lengths of alkyl residue and bovine serum albumin

Energy Technology Data Exchange (ETDEWEB)

Lebedeva, Natalya Sh., E-mail: nsl@isc-ras.ru [G.A. Krestov Institute of Solution Chemistry of the Russian Academy of Sciences, Akademicheskaya, 1, 153045 Ivanovo (Russian Federation); Gubarev, Yury A.; Vyugin, Anatoly I. [G.A. Krestov Institute of Solution Chemistry of the Russian Academy of Sciences, Akademicheskaya, 1, 153045 Ivanovo (Russian Federation); Koifman, Oscar I. [Research Institute of Macroheterocycles of Ivanovo State University of Chemistry and Technology, 153000 Ivanovo (Russian Federation)

2015-10-15

Interaction between bovine serum albumin and alkoxy substituted phthalocyanines was studied by means of electron absorption spectroscopy, fluorescence spectroscopy and viscosimetry. The binding constants and binding distance were calculated. It was found that ZnPc(4-NH-CO-C{sub 6}H{sub 4}-OC{sub 10}H{sub 21}){sub 4} prevents twisting of BSA molecule and localizes between subdomains IB and IIA in protein globule. ZnPc(4-NH-CO-C{sub 6}H{sub 4}-OC{sub 6}H{sub 13}){sub 4} and ZnPc(4-NH-CO-C{sub 6}H{sub 4}-OC{sub 8}H{sub 17}){sub 4} are located on the outer surface of the protein globule. In the case of ZnPc(4-NH-CO-C{sub 6}H{sub 4}-OC{sub 3}H{sub 7}){sub 4} it can be assumed that the phthalocyanine molecule is in the immediate vicinity of the subdomains IB and IIA. - Highlights: • Interaction between bovine serum albumin and alkoxy substituted phthalocyanines was studied by means of electron absorption spectroscopy, fluorescence spectroscopy and viscosimetry. • The binding constants and binding distance were calculated by using the Scatchard method. • Photochemical characteristics of phthalocyanines of studied phthalocyanines are defined. • Localization of phthalocyanines on the protein globule is defined.

Photoelectrochemical performance of N-doped ZnO branched nanowire photoanodes

Directory of Open Access Journals (Sweden)

Shrok Allami

2017-10-01

Full Text Available A ZnO branched-nanowire (BNW photoanode was doped with N for use in a photoelectrochemical cell (PEC to generate H2 from water splitting. First, ZnO BNWs were synthesized by chemical bath deposition method. Two experimental methods were used for N-doping: the time-controlled direct-current glow discharge plasma (DCGDP and the DC magnetron plasma (DCMP methods, to optimize N-doping of the NW structure. X-ray photoelectron spectroscopy (XPS provided the N distribution and atomic percentage in the BNWs. The XPS results confirmed that N distribution into ZnO BNWs occurred by N substitution of O sites in the ZnO structure and through well-screened molecular N2. The morphologies and structures of the fabricated nanostructures were investigated by field-emission scanning electron microscopy and X-ray diffraction respectively. The photoanode performance was demonstrated in photoelectrochemical studies at various power densities under both dark and illuminated conditions. Increasing the N amount in the ZnO BNWs increased the photocurrent in the PEC. Keywords: Engineering, Condensed matter physics, Nanotechnology, Materials science

The Influence of Oxygen Substitution on the Optoelectronic Properties of ZnTe

Directory of Open Access Journals (Sweden)

Imad Khan

2016-01-01

Full Text Available We communicate theoretical results of the structural, electronic, and optical properties of ZnOxTe1-x (0≤x≤1 in the zincblende structure. The calculations are performed using full potential linearized augmented plane waves (FP-LAPW method, based on density functional theory (DFT. The structural properties are calculated with simple GGA (PBEsol, while the electronic and optical properties are calculated using mBJ-GGA. The mBJ-GGA is used to properly treat the active d-orbital in their valence shell. The ZnOTe alloy is highly lattice mismatched and consequently the lattice constants and bulk moduli largely deviate from the linear behavior. The calculated bandgaps are in agreement with the experimentally measured values, where the nature of bandgaps is direct for the whole range of x except at x=0.25. We also calculate the bandgap bowing parameter from our accurate bandgaps and resolve the existing controversy in this parameter.

Effect on the structural, DC resistivity and magnetic properties of Zr and Cu co-SubstitutedNi0.5Zn0.5Fe2O4using sol-gel auto-combustion method

Science.gov (United States)

Jalaiah, K.; Vijaya Babu, K.; Chandra mouli, K.; Subba Rao, P. S. V.

2018-04-01

The Zr and Cu co-substituted Ni0.5Zn0.5Fe2O4 ferrite nanoparticles have been synthesized by the sol-gel auto combustion method. The XRD patterns confirmed single phase cubic spinel structure for present ferrite systems. The substitution of co-dopants in the spinel structure initially decreases the lattice parameter from x = 0.00 to 0.08 and thereafter increases and the same tendency reflecting in cell volume. The DC resistivity was initially increased later followed the decreasing trend; however the drift mobility of all ferrite samples appears to be in opposite phenomenon to DC resistivity. The saturation magnetization and net magnetic moments of all ferrite samples are decreasing with increasing dopant concentration. The coercive field and Y-K angles are increased with dopant concentration. The initial permeability of all samples is decreased with increasing dopant concentration. The Q-Factor for all samples shows the narrow frequency band with increasing frequency.

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 39; Issue 5. Structure and magnetic properties of Zr–Mn substituted strontium hexaferrite Sr(Zr,Mn) x Fe 12 − 2 x O 19 nanoparticles synthesized by sol–gel auto-combustion method. S ALAMOLHODA S M MIRKAZEMI Z GHIAMI M NIYAIFAR. Volume 39 Issue 5 ...

Progress in ZnO Acceptor Doping: What Is the Best Strategy?

Directory of Open Access Journals (Sweden)

Judith G. Reynolds

2014-01-01

Full Text Available This paper reviews the recent progress in acceptor doping of ZnO that has been achieved with a focus toward the optimum strategy. There are three main approaches for generating p-type ZnO: substitutional group IA elements on a zinc site, codoping of donors and acceptors, and substitution of group VA elements on an oxygen site. The relevant issues are whether there is sufficient incorporation of the appropriate dopant impurity species, does it reside on the appropriate lattice site, and lastly whether the acceptor ionization energy is sufficiently small to enable significant p-type conduction at room temperature. The potential of nitrogen doping and formation of the appropriate acceptor complexes is highlighted although theoretical calculations predict that nitrogen on an oxygen site is a deep acceptor. We show that an understanding of the growth and annealing steps to achieve the relevant acceptor defect complexes is crucial to meet requirements.

Effect of Zn on the structural and electrical properties of high temperature HgBa2Ca2Cu3O8+δ superconductor

Science.gov (United States)

Omar, Bilal A.; Fathi, Sabah J.; Jassim, Kareem A.

2018-05-01

Bulk polycrystalline HgBa2Ca2-yZnyCu3O8+δ compound samples with y =0.0, 0.05, 0.1, 0.15, 0.2, 0.25, and 0.3, are synthesized by a solid state reaction process. Study identifies Zinc partial substitution on superconductivity behavior. Structural properties are studied by using X-ray powder pattern, the high temperature phase superconductor (Hg-1223) of the tetragonal structure didn't change with the partial substitution of Zn ions in Ca site, lattice parameters c, c/a are established to vary Zn-substitution. The surface morphology has been studied by using atomic force microscopes (AFM), showed that all specimens have good crystalline and homogeneous surface. Also give a best nano size value is 83.29 nm at y=0.05. Four probe technique is used to measure Tc. The highest Tc and oxygen content were found to be Tc=132 K for y=0.05 after that, Tc decreases from 132 K to 115 K with increasing Zn. In addition, dielectric properties (dielectric constant, dielectric loss factor, and the alternating electrical conductivity) are characterized directly by relating with Zn concentration.

Amendment of saturation magnetization, blocking temperature and particle size homogeneity in Mn-ferrite nanoparticles using Co-Zn substitution

Energy Technology Data Exchange (ETDEWEB)

Eltabey, M.M. [Basic Engineering Science Department, Faculty of Engineering, Menoufiya University (Egypt); Physics Department, Faculty of Science, Jazan University, Jazan (Saudi Arabia); Massoud, A.M., E-mail: Amassouda1@yahoo.com [Physics Department, Faculty of Science, Ain Shams University, Abbassia 11566, Cairo (Egypt); Radu, Cosmin [Lake Shore Cryotronics, Inc., Westerville, OH (United States)

2017-01-15

Nanocrystalline particles of compositions (CoZn){sub x}Mn{sub 1−x}Fe{sub 2}O{sub 4} were prepared by the coprecipitation method from stoichiometric aqueous solutions, where x varies from 0 to 0.3 in steps of 0.05. The synthesized powders were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM) and Fourier transform infrared spectroscopy (FT-IR). A vibrating sample magnetometer (VSM) was used to measure the hysteresis parameters at 300 and 6 K. Zero field cooling (ZFC) and field cooling (FC) curves were obtained at the temperature range 6–400 K and the blocking temperature values were determined. XRD analysis confirmed the formation of the obtained powder in a single cubic spinel phase and it showed also that the lattice parameter is decreasing with the increase of (Co-Zn) content. FT-IR measurements between 160 and 650 cm{sup −1} also confirmed the intrinsic cation vibrations of the spinel structure. The magnetic measurements showed that the saturation magnetization, coercivity and the values of blocking temperatures were increased with the (Co-Zn) content. TEM micrographs declared the improvement of particle size homogeneity with the increase of (Co-Zn) content without remarkable change in the average particle size. The obtained results were discussed in view of A-B sublattices interaction and superparamagnetic phenomenon. - Highlights: • Nanocrystalline particles of compositions (CoZn){sub x}Mn{sub 1-x}Fe{sub 2}O{sub 4} were prepared by the coprecipitation method. • XRD analysis showed that the lattice parameter is decreased with the increase of (Co,Zn) content. • The saturation magnetization is improved with the (Co,Zn) content. • Particle size homogeneity is enhanced with (Co,Zn) content. • The values of blocking temperatures are enhanced with increasing (Co,Zn) content.

M-type barium hexa ferrite magnetic material for anti radar materials at s band frequency

International Nuclear Information System (INIS)

Priyono; Azwar Manaf

2010-01-01

In this paper, preparation and characteristic evaluation of microwave absorber materials of BaFe_1_2_-_2_x Mn_x Ti _xO_1_9 (x = 0,0 - 1,5) compositions are discussed. The absorber material was obtained by a co-substitution of Mn and Ti to Fe in a Barium Hexaferrite (BaO.6Fe_2O_3 ) basic compound through a mechanical alloying process. In this respect, a co-substitution of Mn and Ti ions for Fe was applied to Fe_2O_3 component at a temperature ~ 1,300 °C. The substituted alloy component was further alloyed mechanically with BaCO_3 to form M-Type hexaferrite after the solid state reaction. Identification of X-ray diffraction peaks for the mechanically alloyed materials indicates confidently that a single phase BaFe_1_2_-_x_-_yMn_x Ti_yO_1_9 material was formed. Materials characterization is covering the average grain sizes and absorption of microwaves in the frequency range 1-6 GHz. Absorption with a relatively high coefficient at frequencies ~ 2,000 MHz and ~ 3,500 MHz within the available frequency range was obtained. It is shown that the co-substitution of Mn and Ti ion able to widen the absorption frequency especially in the frequencies of about 3,500 MHz. (author)

Raman study of alloy potential fluctuations in MgxZn1-xO nanopowders

International Nuclear Information System (INIS)

Pan, C-J; Lin, K-F; Hsu, W-T; Hsieh, W-F

2007-01-01

The blueshift of near-band-edge emission and excitonic absorption indicate that Zn 2+ ions are successfully substituted by Mg 2+ ions in Mg x Zn 1-x O nanopowders for 0≤x≤0.14. The changes in Raman spectral linewidth and the asymmetry of the E 2 (high) mode for various Mg contents can be well described by a modified spatial correlation model that considers the grain size distribution. With increasing Mg concentration, the alloy potential fluctuations lead to a decrease in the grain size, which is induced by the surplus Mg 2+ that could form MgO clusters surrounding the crystalline MgZnO

Cadmium free high efficiency Cu2ZnSn(S,Se4 solar cell with Zn1−xSnxOy buffer layer

Directory of Open Access Journals (Sweden)

Md. Asaduzzaman

2017-06-01

Full Text Available We have investigated the simulation approach of a one-dimensional online simulator named A Device Emulation Program and Tool (ADEPT2.1 and the device performances of a thin film solar cell based on Cu2ZnSn(S,Se4 (CZTSSe absorber have been measured. Initiating with a thin film photovoltaic device structure consisting of n-ZnO:Al/i-ZnO/Zn1-xSnxOy (ZTO/CZTSSe/Mo/SLG stack, a graded space charge region (SCR and an inverted surface layer (ISL were inserted between the buffer and the absorber. The cadmium (Cd free ZTO buffer, a competitive substitute to the CdS buffer, significantly contributes to improve the open-circuit voltage, Voc without deteriorating the short-circuit current density, Jsc. The optimized solar cell performance parameters including Voc, Jsc, fill factor (FF, and efficiency (η were calculated from the current density-voltage curve, also known as J–V characteristic curve. The FF was determined as 73.17%, which in turns, yields a higher energy conversion efficiency of 14.09%.

Low Temperature Hydrothermal Growth of ZnO Nanorod Films for Schottky Diode Application

International Nuclear Information System (INIS)

Singh, Shaivalini; Park, Si-Hyun

2016-01-01

The purpose of this research is to report on the fabrication and characterizations of Pd/ZnO nanorod-based Schottky diodes for optoelectronic applications. ZnO nanorods (NRs) were grown on silicon (Si) substrates by a two step hydrothermal method. In the first step, a seed layer of pure ZnO was deposited from a solution of zinc acetate and ethyl alcohol, and then in the second step, the main growth of the ZnO NRs was done over the seed layer. The structural morphology and optical properties of the ZnO NR films were characterized by x-ray diffraction (XRD), scanning electron microscopy (SEM) and UV-vis spectroscopy. The electrical characterization of the Pd/ZnO NR contacts was studied using a current-voltage (I-V) tool. The ZnO NR films exhibited a wurtzite ZnO structure,and the average length of the ZnO NRs were in the range of 750 nm to 800 nm. The values of ideality factor, turn-on voltage and reverse saturation current were calculated from the I-V characteristics of Pd/ZnO NR-based Schottky diodes. The study demonstrates that Pd/ZnO NR Schottky contacts fabricated by a simple and inexpensive method can be used as a substitute for conventional Schottky diodes for optoelectronic applications.

Hydrothermal synthesis of ZnSe:Cu quantum dots and their luminescent mechanism study by first-principles

Energy Technology Data Exchange (ETDEWEB)

Liang, Qingshuang; Bai, Yijia; Han, Lin; Deng, Xiaolong [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Graduate School, Chinese Academy of Sciences, Beijing 10049 (China); Wu, Xiaojie [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Wang, Zhongchang [WPI Research Center, Advanced Institute for Materials Research, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai 980-8577 (Japan); Liu, Xiaojuan, E-mail: lxjuan@ciac.jl.cn [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Meng, Jian, E-mail: jmeng@ciac.jl.cn [State Key Laboratory of Rare Earth Resources Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2013-11-15

An one-pot synthesis of aqueous ZnSe:Cu nanocrystals (NCs) is realized in aqueous solution by a facile yet efficient hydrothermal technique. The dopant emission spectrum of the NCs is tunable, spanning a wide range from 438 to 543 nm. Room-temperature quantum yield for the NCs prepared at the optimal conditions reaches as high as 20% without any post-treatment. The ZnSe:Cu NCs prepared in a neutral aqueous solution (pH=8) are remarkably stable and exhibit comparatively high photoluminescent quantum yield (PL QY) as high as 17%. First-principles pseudopotential calculations using plane-wave basis functions have been performed. The formation energies of copper ions occupied in the interstitial octahedron and substitutional tetrahedral Zn{sup 2+} sites have been calculated. The occupation of copper ions in the interstitial octahedral site is found to be more thermodynamics-facilitated by −0.98 eV. The density of state analysis indicates that the Cu-related emission is primary dominated by the substitutional tetrahedral Cu ions, and the large dopant related emission width of ZnSe:Cu NCs originated from the corresponding Cu 3d impurity band. Highlights: • One-pot synthesis of aqueous ZnSe:Cu nanocrystals with tunable emission and high QY%. • ZnSe:Cu NCs exhibit high QY% at neutral pH suitable for biological application. • The microscopic mechanism underlying Cu-related emission has been provided.

Novel optical properties of CdS:Zn rocksalt system (a theoretical study)

Science.gov (United States)

Khan, M. Junaid Iqbal; Nauman Usmani, M.; Kanwal, Zarfishan

2017-11-01

In present computational study, we focus on optical properties of Zn doped CdS for 1  ×  1  ×  2 and 2  ×  2  ×  2 supercell configurations. Cd atoms are substituted with Zn atoms and results for optical properties demonstrate different trends due to interaction of Zn with S atoms. The study has been performed by PBE-GGA approach using Wien2K within framework of DFT. TDOS and PDOS represent that S-3p states are responsible for conduction. For large supercell configuration, a tremendous change in optical properties has been observed due to different bonding. Optical absorption tends to increase in visible range which supports candidacy of Zn doped CdS for enhanced optoelectronic and nanotechnology applications.

Effect of Mg substitution on the magnetic properties of Ni–Zn ferrites

Indian Academy of Sciences (India)

Y Ramesh Babu

2017-05-31

May 31, 2017 ... C for 6h in air to investigate their structural and magnetic properties. X-ray diffraction ... The tetrava- lent substitutions have been found to improve the .... ducted on ferrites prepared by ceramic method [11] and wet chemical ...

Three-dimensional hole transport in nickel oxide by alloying with MgO or ZnO

Science.gov (United States)

Alidoust, Nima; Carter, Emily A.

2015-11-01

It has been shown previously that the movement of a hole in nickel oxide is confined to two dimensions, along a single ferromagnetic plane. Such confinement may hamper hole transport when NiO is used as a p-type transparent conductor in various solar energy conversion technologies. Here, we use the small polaron model, along with unrestricted Hartree-Fock and complete active space self-consistent field calculations to show that forming substitutional MxNi1-xO alloys with M = Mg or Zn reduces the barrier for movement of a hole away from the ferromagnetic plane to which it is confined. Such reduction occurs for hole transfer alongside one or two M ions that have been substituted for Ni ions. Furthermore, the Mg and Zn ions do not trap holes on O sites in their vicinity, and NiO's transparency is preserved upon forming the alloys. Thus, forming MxNi1-xO alloys with M = Mg or Zn may enhance NiO's potential as a p-type transparent conducting oxide, by disrupting the two-dimensional confinement of holes in pure NiO.

Resorption Rate Tunable Bioceramic: Si, Zn-Modified Tricalcium Phosphate

Energy Technology Data Exchange (ETDEWEB)

Wei, Xiang [Iowa State Univ., Ames, IA (United States)

2006-01-01

This dissertation is organized in an alternate format. Several manuscripts which have already been published or are to be submitted for publication have been included as separate chapters. Chapter 1 is a general introduction which describes the dissertation organization and introduces the human bone and ceramic materials as bone substitute. Chapter 2 is the background and literature review on dissolution behavior of calcium phosphate, and discussion of motivation for this research. Chapter 3 is a manuscript entitled ''Si,Zn-modified tricalcium phosphate: a phase composition and crystal structure study'', which was published in ''Key Engineering Materials'' [1]. Chapter 4 gives more crystal structure details by neutron powder diffraction, which identifies the position for Si and Zn substitution and explains the stabilization mechanism of the structure. A manuscript entitled ''Crystal structure analysis of Si, Zn-modified Tricalcium phosphate by Neutron Powder Diffraction'' will be submitted to Biomaterials [2]. Chapter 5 is a manuscript, entitled ''Dissolution behavior and cytotoxicity test of Si, Zn-modified tricalcium phosphate'', which is to be submitted to Biomaterials [3]. This paper discusses the additives effect on the dissolution behavior of TCP, and cytotoxicity test result is also included. Chapter 6 is the study of hydrolysis process of {alpha}-tricalcium phosphate in the simulated body fluid, and the phase development during drying process is discussed. A manuscript entitled ''Hydrolysis of {alpha}-tricalcium phosphate in simulated body fluid and phase transformation during drying process'' is to be submitted to Biomaterials [4]. Ozan Ugurlu is included as co-authors in these two papers due to his TEM contributions. Appendix A is the general introduction of the materials synthesis, crystal structure and preliminary dissolution result. A manuscript entitled

Structural refinement, photoluminescence and Raman spectroscopy of wurtzite Mn-doped Zn O pellets

Energy Technology Data Exchange (ETDEWEB)

Marquina, J.; Martin, J.; Luengo, J.; Vera, F.; Roa, L. [Centro de Estudios Avanzados en Optica, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Gonzalez, J. [Centro de Estudios de Semiconductores, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of); Rodriguez, F.; Renero L, C.; Valiente, R. [Malta-Consolider Team, CITIMAC, Facultad de Ciencias, Universidad de Cantabria, Santander 69005 (Spain); Delgado, G. E., E-mail: marquinajesus@gmail.com [Laboratorio de Cristalografia, Facultad de Ciencias, Universidad de los Andes, Merida 5101 (Venezuela, Bolivarian Republic of)

2017-11-01

We report the results of the Rietveld refinement, photoluminescence and Raman spectroscopy of Mn-doped Zn O ceramic pellets. Rietveld refinement shows that samples crystallize in the wurtzite structure and for the Mn-doped sample indicated that the Mn atoms substitute the Zn tetrahedral crystallographic sites in the Zn O host lattice. The emission and absorption spectra of Mn-doped Zn O have been investigated in the visible-UV region and the data have been interpreted in terms of the wurtzite Zn O electronic structure. Two broad bands, one due to superposition between donor bound excitons (DX) and free excitons (FX) and other due free-to bond excitonic recombination (FB) dominates the low-temperature photoluminescence spectra of Mn-doped Zn O bulk. In the Raman spectrum, an extra mode at ∼520 cm{sup -1} has been observed in agreement with earlier works, and it is an indicator for the incorporation of Mn{sup +2} ions into the Zn O host matrix since it is not is observed in Zn O pristine. Rietveld refinement of the X-ray diffraction patterns, energy-dispersive X-ray spectroscopy (EDS) technique, and Raman spectroscopies were performed to study these effects. (Author)

Ferromagnetism in Gd doped ZnO nanowires: A first principles study

KAUST Repository

Aravindh, S. Assa

2014-12-19

In several experimental studies, room temperature ferromagnetism in Gd-doped ZnO nanostructures has been achieved. However, the mechanism and the origin of the ferromagnetism remain controversial. We investigate the structural, magnetic, and electronic properties of Zn 48O48 nanowires doped with Gd, using density functional theory. Our findings indicate that substitutionally incorporated Gd atoms prefer occupying the surface Zn sites. Moreover, the formation energy increases with the distance between Gd atoms, signifying that no Gd-Gd segregation occurs in the nanowires within the concentration limit of ≤2%. Gd induces ferromagnetism in ZnO nanowires with magnetic coupling energy up to 21 meV in the neutral state, which increases with additional electron and O vacancy, revealing the role of carriers in magnetic exchange. The potential for achieving room temperature ferromagnetism and high TC in ZnO:Gd nanowires is evident from the large ferromagnetic coupling energy (200 meV) obtained with the O vacancy. Density of states shows that Fermi level overlaps with Gd f states with the introduction of O vacancy, indicating the possibility of s-f coupling. These results will assist in understanding experimental findings in Gd-doped ZnO nanowires.

Ferromagnetism in Gd doped ZnO nanowires: A first principles study

KAUST Repository

Aravindh, S. Assa; Schwingenschlö gl, Udo; Roqan, Iman S.

2014-01-01

In several experimental studies, room temperature ferromagnetism in Gd-doped ZnO nanostructures has been achieved. However, the mechanism and the origin of the ferromagnetism remain controversial. We investigate the structural, magnetic, and electronic properties of Zn 48O48 nanowires doped with Gd, using density functional theory. Our findings indicate that substitutionally incorporated Gd atoms prefer occupying the surface Zn sites. Moreover, the formation energy increases with the distance between Gd atoms, signifying that no Gd-Gd segregation occurs in the nanowires within the concentration limit of ≤2%. Gd induces ferromagnetism in ZnO nanowires with magnetic coupling energy up to 21 meV in the neutral state, which increases with additional electron and O vacancy, revealing the role of carriers in magnetic exchange. The potential for achieving room temperature ferromagnetism and high TC in ZnO:Gd nanowires is evident from the large ferromagnetic coupling energy (200 meV) obtained with the O vacancy. Density of states shows that Fermi level overlaps with Gd f states with the introduction of O vacancy, indicating the possibility of s-f coupling. These results will assist in understanding experimental findings in Gd-doped ZnO nanowires.

Preparation of ZnO/CdS/BC Photocatalyst Hybrid Fiber and Research of Its Photocatalytic Properties

Directory of Open Access Journals (Sweden)

Beibei Dai

2015-01-01

Full Text Available An environment-friendly biomaterial bacterial cellulose (BC is introduced to substitute general organic polymers to assist the preparation of ZnO/CdS/BC photocatalyst hybrid nanofiber through coprecipitation method under the low-temperature condition. The XRD, XPS, and SEM results show that high load of ZnO/CdS/BC ternary hybrid fiber can be produced. TGA curves scan shows that ZnO/CdS/BC hybrid fiber has better thermal properties than bacterial cellulose. The UV-Vis spectra of the ZnO/CdS/BC hybrid nanofiber (0, 10, 20, and 50 wt%, resp. show that photocatalytic activities of ZnO/CdS/BC are influenced by the added amount of CdS. The degradation curve of methyl shows that ZnO/CdS/BC nanohybrid fibers exhibit excellent photocatalytic efficiency.

Synthesis and properties of Pr-substituted MgZn ferrites for core materials and high frequency applications

International Nuclear Information System (INIS)

Mukhtar, Muhammad Waqas; Irfan, Muhammad; Ahmad, Ishtiaq; Ali, Ihsan; Akhtar, Majid Niaz; Khan, Muhammad Azhar; Abbas, Ghazanfar; Rana, M.U.; Ali, Akbar; Ahmad, Mukhtar

2015-01-01

A series of single phase spinel ferrites having chemical formula Mg 0.5 Zn 0.5 Pr x Fe 2−x O 4 (x=0.00, 0.05, 0.10, 0.15, 0.20, 0.25) were prepared using the sol–gel technique after sintering at 700 °C. The thermal decomposition behavior of an as prepared powder was investigated by means of DTA/TGA analyses. The sintered powders were then characterized by Fourier transform infrared spectroscope, X-ray diffraction, scanning electron microscope, energy dispersive X-ray spectroscope and vibrating sample magnetometer. X-ray diffraction patterns confirm the single phase spinel structure of prepared ferrites without the presence of any impurity phase. The value of lattice parameter (a) increases with the increase of Pr contents (x) into the spinel lattice. The grain size estimated from electron microscope images is in the range of 2.75–5.4 µm which confirms the spinel crystalline nature of the investigated samples. The saturation magnetization (M s ) decreases whereas coercivity (H c ) increases with the increase of Pr contents (x). The measured parameters suggest that these materials are favorable for high frequency applications and as core materials. - Highlights: • Pr-substituted spinel ferrites synthesized by autocombustion route have been investigated. • The average grain size was in the range of 2.75–5.4 µm estimated by SEM technique. • The (M s ) decreases whereas (H c ) increases with the increase of Pr contents (x). • These parameters are favorable for high frequency applications and as core materials

Competition of the self-activated and Mn-related luminescence in ZnS single crystals

Science.gov (United States)

Bacherikov, Yu. Yu.; Vorona, I. P.; Markevich, I. V.; Korsunska, N. O.; Kurichka, R. V.

2018-06-01

The photoluminescence (PL) and photoluminescence excitation (PLE) spectra of ZnS single crystals thermally doped from ZnS/MnS mixture were studied at 300 and 77 K. PL spectra exhibit bands caused by Mn-related centers and centers of self-activated (SA) emission. Besides intrinsic maximum, a number of narrow peaks corresponded to Mn-related absorption are found in the PLE spectra of both SA and Mn-related emission. A redistribution of SA and Mn-related emission intensities is observed with temperature change. The mechanism of this phenomenon involving free hole trapping by MnZn and the possible position of a ground energy level of substitutional Mn are discussed.

Structure and defect studies of In2O3:Zn,Zr for higher stability TCO

Science.gov (United States)

Herwadkar, Aditi; Kim, Kwiseon

2010-03-01

The defects structures among the transparent conducting oxides (TCO) plays a major role in determining stability of the oxide over a temperature range and in tuning electrical and optical properties for the different TCO applications In2O3 crystallizes in the cubic bixbyite structure. The structure can be derived from the related fluorite structure by removing one fourth of the anions and allowing for small shifts of the ionic positions. In2O3 has two non-equivalent six-fold coordinated cation sites. For one of the sites, the cation is bounded by two structural vacancy along the body diagonal and for the other non-equivalent site the vacancies lie along the face diagonal. These vacancies are actually empty oxygen vacancy positions. Indium is in +3 charge state. ZnO on the other hand crystallizes to form wurtzite structure with four-fold coordination for Zn and is in +2 charge state where as the crystal structure of ZrO is rulite with Zr in +4 charge state and is four fold coordinated. Co-doping of Zn and Zr with each substituting the In atom satisfies the octet rule and is lower in energy then the individual substitutions with overall neutrality. The formation enthalpy as a function of pair (Zn, Zr) shows a minimum at experimental composition of In2(Zn,Zr)3O24. We in this work present the electronic structure optimization and study the defect states in this material.

Differential Binding of Co(II) and Zn(II) to Metallo-beta-Lactamase Bla2 from Bacillus anthracis

Energy Technology Data Exchange (ETDEWEB)

Hawk, M.; Breece, R; Hajdin, C; Bender, K; Hu, Z; Costello, A; Bennett, B; Tierney, D; Crowder, M

2009-01-01

In an effort to probe the structure, mechanism, and biochemical properties of metallo-{beta}-lactamase Bla2 from Bacillus anthracis, the enzyme was overexpressed, purified, and characterized. Metal analyses demonstrated that recombinant Bla2 tightly binds 1 equiv of Zn(II). Steady-state kinetic studies showed that mono-Zn(II) Bla2 (1Zn-Bla2) is active, while di-Zn(II) Bla2 (ZnZn-Bla2) was unstable. Catalytically, 1Zn-Bla2 behaves like the related enzymes CcrA and L1. In contrast, di-Co(II) Bla2 (CoCo-Bla2) is substantially more active than the mono-Co(II) analogue. Rapid kinetics and UV-vis, 1H NMR, EPR, and EXAFS spectroscopic studies show that Co(II) binding to Bla2 is distributed, while EXAFS shows that Zn(II) binding is sequential. To our knowledge, this is the first documented example of a Zn enzyme that binds Co(II) and Zn(II) via distinct mechanisms, underscoring the need to demonstrate transferability when extrapolating results on Co(II)-substituted proteins to the native Zn(II)-containing forms.

An investigation on the microstructures and magnetic properties of the Sr0.35−xBaxCa0.30La0.35Fe11.71Co0.29O19 hexaferrites

International Nuclear Information System (INIS)

Yang, Yujie; Liu, Xiansong

2014-01-01

M-type hexaferrite Sr 0.35−x Ba x Ca 0.30 La 0.35 Fe 11.71 Co 0.29 O 19 (0≤x≤0.35) magnetic powders and magnets were prepared by the solid-state reaction. The phase compositions of the magnetic powders were investigated by X-ray diffraction. X-ray diffraction patterns show that the hexagonal single phase is obtained in all samples. The micrographs of the magnets were observed by a field emission scanning electron microscopy. All magnets have formed hexagonal structures and the particles are distributed evenly. Magnetic properties of the magnets were measured by a magnetic properties test instrument. The remanence, intrinsic coercivity, magnetic induction coercivity and maximum energy product of the magnets continuously decrease with increasing barium content (x). - Highlights: • Hexaferrites Sr 0.35−x Ba x Ca 0.30 La 0.35 Fe 11.71 Co 0.29 O 19 were prepared by the solid-state reaction. • The hexagonal single phase is obtained in all magnetic powders. • B r , H cj , H cb and (BH) max of the magnets continuously decrease with increasing barium content

The crystalline and magnetic properties of Zn doped strontium Z-type hexaferrite synthesized by polymerizable complex method

Directory of Open Access Journals (Sweden)

Jung Tae Lim

2017-05-01

Full Text Available Polycrystalline samples of Sr3Co2-xZnxFe24O41 (x = 0.0, 0.5, 1.0, 1.5, 2.0 were synthesized by a polymerizable complex method. The crystallographic, and magnetic properties of samples were investigated using x-ray diffractometer (XRD, vibrating sample magnetometer (VSM, and Mössbauer spectroscopy. The crystal structures of all samples were determined to be hexagonal with the space group P63/mmc. The hysteresis curves under 10 kOe at 295 K showed that all samples were not saturated due to the high planar anisotropy of Sr ions. In addition, the coercivity (Hc of samples decreased with increasing Zn ion contents. Mössbauer spectra of all samples were obtained at 295 K, and least-squares fitted below TC as six distinguishable sextets (4fIV, 4fIV*, 12kVI*, 4fVI*+ 4eIV, 12kVI, and 2dV + 2aVI + 4fVI + 4eVI.

Photoluminescence studies of ZnO doped with stable and radioactive impurities

CERN Document Server

Cullen, Joseph; Martin O, Henry

In this work the IIb-VI compound semiconductor ZnO is doped, via ion implantation of stable and radioactive isotopes, in order to investigate the chemical nature of exciton re-combinations bound to previously unidentified defects. Photo-luminescence (PL) is discussed and is used extensively as the primary investigative technique. A new defect emission feature, centred around 3.324 eV, is found to be related to Ge impurities occupying substitutional Zn sites in ZnO. This centre is investigated by temperature dependent PL, piezo-spectroscopy and Zeeman spectroscopy. The centre is donor-like in nature. Uniaxial stress measurements indicate that the defect centre has trigonal symmetry and applied magnetic field measurements reveal the neutral charge state of the centre and the donor-like binding mechanism. Subsequent to this, a study is undertaken of the iso-electronic defect Hg in ZnO studying the zero phonon feature at 3.279 eV and its associated phonon replica band. Temperature dependent measurements reveal tw...

Amphoteric Be in GaN: Experimental Evidence for Switching between Substitutional and Interstitial Lattice Sites

Science.gov (United States)

Tuomisto, Filip; Prozheeva, Vera; Makkonen, Ilja; Myers, Thomas H.; Bockowski, Michal; Teisseyre, Henryk

2017-11-01

We show that Be exhibits amphoteric behavior in GaN, involving switching between substitutional and interstitial positions in the lattice. This behavior is observed through the dominance of BeGa in the positron annihilation signals in Be-doped GaN, while the emergence of VGa at high temperatures is a consequence of the Be impurities being driven to interstitial positions. The similarity of this behavior to that found for Na and Li in ZnO suggests that this could be a universal property of light dopants substituting for heavy cations in compound semiconductors.

Magnetic properties of Sn-substituted Ni-Zn ferrites synthesized from nano-sized powders of NiO, ZnO, Fe2O3, and SnO2

Science.gov (United States)

Ali, MA; Uddin, MM; Khan, MNI; Chowdhury, FUZ; Hoque, SM; Liba, SI

2017-06-01

A series of Ni0.6-x/2Zn0.4-x/2Sn x Fe2O4 (x = 0.0, 0.05, 0.1, 0.15, 0.2, and 0.3) (NZSFO) ferrite composities have been synthesized from nano powders using a standard solid state reaction technique. The spinel cubic structure of the investigated samples has been confirmed by x-ray diffraction (XRD). The magnetic properties such as saturation magnetization ({M}{{s}}), remanent magnetization ({M}{{r}}), coercive field ({H}{{c}}), and Bohr magneton (μ) are calculated from the hysteresis loops. The value of {M}{{s}} is found to decrease with increasing Sn content in the samples. This change is successfully explained by the variation of A-B interaction strength due to Sn substitution in different sites. The compositional stability and quality of the prepared ferrite composites have also been endorsed by the fairly constant initial permeability ({μ }^{\\prime }) over a wide range of frequency. The decreasing trend of {μ }^{\\prime } with increasing Sn content has been observed. Curie temperature {T}{{C}} has been found to increase with the increase in Sn content. A wide spread frequency utility zone indicates that the NZSFO can be considered as a good candidate for use in broadband pulse transformers and wide band read-write heads for video recording. The composition of x = 0.05 shows unusual results and the possible reason is also mentioned with the established formalism.

Microstructure, electronic structure and optical properties of combustion synthesized Co doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Srinatha, N. [Department of Physics, JB Campus, Bangalore University, Bangalore 560056 (India); Nair, K.G.M. [UGC-DAE-CSR, Kalpakkam Node, Kalpakkam, Kokilamedu 603102 (India); Angadi, Basavaraj, E-mail: brangadi@gmail.com [Department of Physics, JB Campus, Bangalore University, Bangalore 560056 (India)

2015-10-01

We report on the microstructure, electronic structure and optical properties of nanocrystalline Zn{sub 1−x}Co{sub x}O (x=0, 0.01, 0.03, 0.05 and 0.07) particles prepared by solution combustion technique using L-Valine as fuel. The detailed structural and micro-structural studies were carried out by XRD, HRTEM and TEM-SAED respectively, which confirms the formation of single phased, nano-sized particles. The electronic structure was determined through NEXAFS and atomic multiplet calculations/simulations performed for various symmetries and valence states of ‘Co’ to determine the valance state, symmetry and crystal field splitting. The correlations between the experimental NEXAFS spectra and atomic multiplet simulations, confirms that, ‘Co’ present is in the 2+ valence state and substituted at the ‘Zn’ site in tetrahedral symmetry with crystal field splitting, 10Dq =−0.6 eV. The optical properties and ‘Co’ induced defect formation of as-synthesized materials were examined by using diffuse reflectance and Photoluminescence spectroscopy, respectively. Red-shift of band gap energy (E{sub g}) was observed in Zn{sub 1−x}Co{sub x}O samples due to Co (0.58 Å) substitution at Zn (0.60 Å) site of the host ZnO. Also, in PL spectra, a prominent pre-edge peak corresponds to ultraviolet (UV) emission around 360–370 nm was observed with Co concentration along with near band edge emission (NBE) of the wide band gap ZnO and all samples show emission in the blue region.

Photoluminescence of ZnS: Mn quantum dot by hydrothermal method

Directory of Open Access Journals (Sweden)

Yun Hu

2018-01-01

Full Text Available ZnS: Mn quantum dots (QDs with the average grain size from 4.2 to 7.2 nm were synthesized by a hydrothermal method. All samples were cubic zinc blende structure (β-ZnS measured using X-ray diffraction (XRD. And the main diffraction peaks of ZnS: Mn shifted slightly towards higher angle in comparison with the intrinsic ZnS because of the substitution of Mn2+ for Zn2+. Due to the small grain size (4-7 nm effect, the poor dispersion and serious reunion phenomenon for the samples were observed from transmission electron microscopy (TEM. ZnS: Mn QDs had four peaks centered at 466, 495, 522, and 554 nm, respectively, in the photoluminescence (PL spectra, in which the band at 554 nm absent in the intrinsic ZnS: Mn is attributed to the doping of Mn2+ in the lattice sites. As the concentration of Mn2+ increasing from 0% to 0.6 at%, the intensity of the PL emission also increased. But the concentration reached 0.9 at%, quenching of PL emission occurred. The peak in ZnS: Mn QDs observed at 490 cm-1 was originated from the stretching vibration of the Mn–O bonds in the Fourier transform infrared (FTIR spectra. And the small changes about this peak compared with the previous reports at 500 cm-1 can be attributed to the formation of quantum dots. This method we utilized to synthesize ZnS: Mn QDs is very simple, low cost, and applicable for other semiconductor QD materials.

CL from ZnO nanowires and microneedles Co-doped with N and Mn

International Nuclear Information System (INIS)

Herrera, M; Morales, A; Díaz, J A

2014-01-01

Cathodoluminescence (CL) was used to study the luminescence emission of ZnO : N, Mn nanowires and microneedles grown by thermal evaporation. CL spectra acquired at room temperature showed the presence of near band edge and defect-related emissions. The defect related emission comprised two bands centered at 2.28 and 2.5 eV. The first component was attributed to the formation of spinel ZnMn 2 O 4  and the second to the well-known ZnO green emission. CL spectra acquired at 100 K showed two emissions centered at 3.22 and 3.25 eV that were attributed to donor–acceptor pair (DAP) and FA transitions, respectively. It was proposed that substitutional nitrogen (N O ) and zinc interstitial (Zn i ) were acceptor and shallow-donor centers in the DAP transition. (paper)

The magnetic properties of aligned M hexa-ferrite fibres

International Nuclear Information System (INIS)

Pullar, R.C.; Bhattacharya, A.K.

2006-01-01

Aligned and random fibres of strontium hexa ferrite (SrM, SrFe 12 O 19 ) and barium hexaferrite (BaM, BaFe 12 O 19 ) were manufactured by blow spinning from an aqueous inorganic sol-gel precursor, which was then fired to give the hexagonal ferrite fibre. Their magnetic properties were studied by VSM, investigating the evolution of these properties with firing and measurement temperature, and in particular the effects of fibre alignment. It has been predicted that aligned ferrite fibres will demonstrate an enhanced magnetisation along the axis of alignment with respect to perpendicular to the axis, and this has been demonstrated here for the first time. The optimum firing temperature was 1000 deg. C, at which point they still had submicron grains. In BaM random fibres M s =63.8 emu g -1 and H c =428.1 kA m -1 , and in SrM random fibres M s =63.3 emu g -1 and H c =452.8 kA m -1 , high values for polycrystalline materials. Fibres aligned parallel to the applied field had saturation magnetisation (M s ) values equal to those of the random fibres, whilst fibres aligned perpendicular to the field had M s values 62% and 75% lower, for BaM and SrM, respectively. There was no change in coercivity (H c ) between random or aligned fibres of any orientation, and fibres aligned 45 deg. and parallel to H appeared identical. Therefore, properties along the axis of alignment were superior when compared to measurements perpendicular to the axis of alignment, giving a directionality to the magnetisation in an otherwise randomly oriented ferrite material

Structural and magnetic properties of Mg-Zn ferrites (Mg{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4}) prepared by sol-gel method

Energy Technology Data Exchange (ETDEWEB)

Reyes-Rodríguez, Pamela Yajaira, E-mail: pamela2244_4@hotmail.com [Cinvestav-Unidad Saltillo, Av. Industrial Metalúrgica #1062, Parque Industrial Saltillo-Ramos Arizpe, CP 25900, México (Mexico); Cortés-Hernández, Dora Alicia; Escobedo-Bocardo, José Concepción; Almanza-Robles, José Manuel; Sánchez-Fuentes, Héctor Javier; Jasso-Terán, Argentina; De León-Prado, Laura Elena [Cinvestav-Unidad Saltillo, Av. Industrial Metalúrgica #1062, Parque Industrial Saltillo-Ramos Arizpe, CP 25900, México (Mexico); Méndez-Nonell, Juan [Centro de Investigación en Materiales Avanzados, Ave. Miguel Cervantes #120, Complejo Industrial Chihuahua, CP 31109 Chihuahua, México (Mexico); Hurtado-López, Gilberto Francisco [Centro de Investigación en Química Aplicada, Blvd. Enrique Reyna Hermosillo #140, CP 25294 Saltillo, Coahuila, México (Mexico)

2017-04-01

In this study, the Mg{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} nanoparticles (x=0–0.9) were prepared by sol-gel method. These ferrites exhibit an inverse spinel structure and the lattice parameter increases as the substitution of Zn{sup 2+} ions is increased. At lower Zn content (0.1≤x≤0.5), saturation magnetization (Ms) increases, while it decreases at higher Zn content (x≥6). The remnant magnetization (0.17–2.0 emu/g) and coercive field (6.0–60 Oe) indicate a ferrimagnetic behavior. The average core diameter of selected ferrites is around 15 nm and the nanoparticles morphology is quasi spherical. The heating ability of some Mg{sub 0.9}Zn{sub 0.1}Fe{sub 2}O{sub 4} and Mg{sub 0.7}Zn{sub 0.3}Fe{sub 2}O{sub 4} aqueous suspensions indicates that the magnetic nanoparticles can increase the medium temperature up to 42 °C in a time less than 10 min - Highlights: • Magnetic nanoparticles of Mg{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} were synthesized by sol-gel method. • Nanoparticles showing a single spinel crystalline structure were obtained. • Aqueous suspensions of Mg{sub 0.7}Zn{sub 0.3}Fe{sub 2}O{sub 4} and Mg{sub 0.9}Zn{sub 0.1}Fe{sub 2}O{sub 4} show heating ability.

Oxidant-Dependent Thermoelectric Properties of Undoped ZnO Films by Atomic Layer Deposition

KAUST Repository

Kim, Hyunho

2017-02-27

Extraordinary oxidant-dependent changes in the thermoelectric properties of undoped ZnO thin films deposited by atomic layer deposition (ALD) have been observed. Specifically, deionized water and ozone oxidants are used in the growth of ZnO by ALD using diethylzinc as a zinc precursor. No substitutional atoms have been added to the ZnO films. By using ozone as an oxidant instead of water, a thermoelectric power factor (σS) of 5.76 × 10 W m K is obtained at 705 K for undoped ZnO films. In contrast, the maximum power factor for the water-based ZnO film is only 2.89 × 10 W m K at 746 K. Materials analysis results indicate that the oxygen vacancy levels in the water- and ozone-grown ZnO films are essentially the same, but the difference comes from Zn-related defects present in the ZnO films. The data suggest that the strong oxidant effect on thermoelectric performance can be explained by a mechanism involving point defect-induced differences in carrier concentration between these two oxides and a self-compensation effect in water-based ZnO due to the competitive formations of both oxygen and zinc vacancies. This strong oxidant effect on the thermoelectric properties of undoped ZnO films provides a pathway to improve the thermoelectric performance of this important material.

Laboratory studies of galvanic corrosion. III. Effect of velocity in NaCl and substitute ocean water

International Nuclear Information System (INIS)

Mansfeld, F.; Kenkel, J.V.

1977-01-01

The galvanic corrosion behavior of 4340 steel coupled to Type 304 stainless steel, Cu, Ti-6Al-4V, Al 2024, Al 6061, and zinc has been studied in 3.5 percent NaCl and ASTM substitute ocean water as a function of velocity using a rotating galvanic couple electrode holder. For steel coupled to Type 304 stainless steel, Cu or Ti, the galvanic current generally increases proportional to the square root of the rotation speed in both media. The increase is, however, smaller in the substitute ocean water. For couples involving Al alloys and Zn, the galvanic current has a more complicated dependence on velocity in substitute ocean water than in 3.5 percent NaCl

Narrowing the gap: from semiconductor to semimetal in the homologous series of rare-earth zinc arsenides RE(2-y)Zn4As4·n(REAs) and Mn-substituted derivatives RE(2-y)Mn(x)Zn(4-x)As4·n(REAs) (RE = La-Nd, Sm, Gd).

Science.gov (United States)

Lin, Xinsong; Tabassum, Danisa; Mar, Arthur

2015-12-14

A homologous series of ternary rare-earth zinc arsenides, prepared by reactions of the elements at 750 °C, has been identified with the formula RE(2-y)Zn4As4·n(REAs) (n = 2, 3, 4) for various RE members. They adopt trigonal structures: RE(4-y)Zn4As6 (RE = La-Nd), space group R3̄m1, Z = 3; RE(5-y)Zn4As7 (RE = Pr, Nd, Sm, Gd), space group P3̄m1, Z = 1; RE(6-y)Zn4As8 (RE = La-Nd, Sm, Gd), space group R3̄m1, Z = 3. The Zn atoms can be partially substituted by Mn atoms, resulting in quaternary derivatives RE(2-y)Mn(x)Zn(4-x)As4·n(REAs). Single-crystal structures were determined for nine ternary and quaternary arsenides RE(2-y)M4As4·n(REAs) (M = Mn, Zn) as representative examples of these series. The structures are built by stacking close-packed nets of As atoms, sometimes in very long sequences, with RE atoms occupying octahedral sites and M atoms occupying tetrahedral sites, resulting in an intergrowth of [REAs] and [M2As2] slabs. The recurring feature of all members of the homologous series is a sandwich of [M2As2]-[REAs]-[M2As2] slabs, while rocksalt-type blocks of [REAs] increase in thickness between these sandwiches with higher n. Similar to the previously known related homologous series REM(2-x)As2·n(REAs) which is deficient in M, this new series RE(2-y)M4As4·n(REAs) exhibits deficiencies in RE to reduce the electron excess that would be present in the fully stoichiometric formulas. Enthalpic and entropic factors are considered to account for the differences in site deficiencies in these two homologous series. Band structure calculations indicate that the semiconducting behaviour of the parent n = 0 member (with CaAl2Si2-type structure) gradually evolves, through a narrowing of the gap between valence and conduction bands, to semimetallic behaviour as the number of [REAs] blocks increases, to the limit of n = ∞ for rocksalt-type REAs.

40 CFR 721.981 - Substituted naphtholoazo-substituted naphthalenyl-substituted azonaphthol chromium complex.

Science.gov (United States)

2010-07-01

... naphthalenyl-substituted azonaphthol chromium complex. 721.981 Section 721.981 Protection of Environment...-substituted naphthalenyl-substituted azonaphthol chromium complex. (a) Chemical substance and significant new... naphtholoazo-substituted naphthalenyl-substituted azonaphthol chromium complex (PMN P-93-1631) is subject to...

Effect of Mg, Ca, and Zn on stability of LiBH{sub 4} through computational thermodynamics

Energy Technology Data Exchange (ETDEWEB)

Lee, Sung Hoon; Manga, Venkateswara Rao; Liu, Zi-Kui [Department of Materials Science and Engineering, The Pennsylvania State University, University Park, PA 16802 (United States)

2010-07-15

The effect of divalent metal-dopants, Mg, Ca, and Zn, on the stability of LiBH{sub 4} is studied by using the first-principles calculations and CALPHAD (CALculation of PHAse Diagram) modeling. The ground states of Mg{sub 1/2}BH{sub 4}, Ca{sub 1/2}BH{sub 4}, and Zn{sub 1/2}BH{sub 4} are shown to be I anti 4m2, F2dd, and I anti 4m2, respectively, through first-principles calculations. Positive enthalpy of mixing between Li and the alloying element is predicted, indicating unfavorable solubility of alloying elements in LiBH{sub 4} and thus offering possibility to decrease the stability of LiBH{sub 4}. The ionic sublattice model of (Li{sup +}, M{sup 2+}, Va){sub 1}(BH{sub 4}{sup -}){sub 1} is adopted for the metal substituted LiBH{sub 4} phase. It is observed that the addition of Mg or Zn has limited effect as the decomposition temperature is between those of LiBH{sub 4} and M{sub 1/2}BH{sub 4} for Mg and Zn substitutions. LiBH{sub 4} is destabilized with magnesium borides or LiZn{sub 4} formation but its decomposition temperature is higher than that of M{sub 1/2}BH{sub 4}. On the other hand, the addition of Ca significantly reduces the H{sub 2} releasing temperature due to the formation of highly stable CaB{sub 6}. (author)

On the interplay of point defects and Cd in non-polar ZnCdO films

International Nuclear Information System (INIS)

Zubiaga, A.; Reurings, F.; Tuomisto, F.; Plazaola, F.; García, J. A.; Kuznetsov, A. Yu.; Egger, W.; Zúñiga-Pérez, J.; Muñoz-Sanjosé, V.

2013-01-01

Non-polar ZnCdO films, grown over m- and r-sapphire with a Cd concentration ranging between 0.8% and 5%, have been studied by means of slow positron annihilation spectroscopy (PAS) combined with chemical depth profiling by secondary ion mass spectroscopy and Rutherford back-scattering. Vacancy clusters and Zn vacancies with concentrations up to 10 17 cm −3 and 10 18 cm −3 , respectively, have been measured inside the films. Secondary ion mass spectroscopy results show that most Cd stays inside the ZnCdO film but the diffused atoms can penetrate up to 1.3 μm inside the ZnO buffer. PAS results give an insight to the structure of the meta-stable ZnCdO above the thermodynamical solubility limit of 2%. A correlation between the concentration of vacancy clusters and Cd has been measured. The concentration of Zn vacancies is one order of magnitude larger than in as-grown non-polar ZnO films and the vacancy cluster are, at least partly, created by the aggregation of smaller Zn vacancy related defects. The Zn vacancy related defects and the vacancy clusters accumulate around the Cd atoms as a way to release the strain induced by the substitutional Cd Zn in the ZnO crystal.

On the interplay of point defects and Cd in non-polar ZnCdO films

Energy Technology Data Exchange (ETDEWEB)

Zubiaga, A.; Reurings, F.; Tuomisto, F. [Department of Applied Physics, Aalto University, P.O. Box 11100, 00076 Aalto, Espoo (Finland); Plazaola, F. [Elektrizitatea eta Elektronika/Fisika Aplikatua II Sailak, Euskal Herriko Unibertsitatea, Posta Kutxatila 644, 48080 Bilbao (Spain); Garcia, J. A. [Fisika Aplikatua II Saila, Euskal Herriko Unibertsitatea, Posta Kutxatila 644, 48080 Bilbao (Spain); Kuznetsov, A. Yu. [Department of Physics, University of Oslo, P.O. Box 1048 Blindern, NO-0316 Oslo (Norway); Egger, W. [Inst. fuer Angewandte Physik und Messtechnik, Univ. der Bundeswehr Muenchen, 87755 Neubiberg (Germany); Zuniga-Perez, J. [CRHEA CNRS, F-06560 Valbonne (France); Munoz-Sanjose, V. [Dept. de Fisica Aplicada i Electromagnetisme, c/ Doctor Moliner 50, E-46100 Burjassot (Valencia) (Spain)

2013-01-14

Non-polar ZnCdO films, grown over m- and r-sapphire with a Cd concentration ranging between 0.8% and 5%, have been studied by means of slow positron annihilation spectroscopy (PAS) combined with chemical depth profiling by secondary ion mass spectroscopy and Rutherford back-scattering. Vacancy clusters and Zn vacancies with concentrations up to 10{sup 17} cm{sup -3} and 10{sup 18} cm{sup -3}, respectively, have been measured inside the films. Secondary ion mass spectroscopy results show that most Cd stays inside the ZnCdO film but the diffused atoms can penetrate up to 1.3 {mu}m inside the ZnO buffer. PAS results give an insight to the structure of the meta-stable ZnCdO above the thermodynamical solubility limit of 2%. A correlation between the concentration of vacancy clusters and Cd has been measured. The concentration of Zn vacancies is one order of magnitude larger than in as-grown non-polar ZnO films and the vacancy cluster are, at least partly, created by the aggregation of smaller Zn vacancy related defects. The Zn vacancy related defects and the vacancy clusters accumulate around the Cd atoms as a way to release the strain induced by the substitutional Cd{sub Zn} in the ZnO crystal.

On the interplay of point defects and Cd in non-polar ZnCdO films

Science.gov (United States)

Zubiaga, A.; Reurings, F.; Tuomisto, F.; Plazaola, F.; García, J. A.; Kuznetsov, A. Yu.; Egger, W.; Zúñiga-Pérez, J.; Muñoz-Sanjosé, V.

2013-01-01

Non-polar ZnCdO films, grown over m- and r-sapphire with a Cd concentration ranging between 0.8% and 5%, have been studied by means of slow positron annihilation spectroscopy (PAS) combined with chemical depth profiling by secondary ion mass spectroscopy and Rutherford back-scattering. Vacancy clusters and Zn vacancies with concentrations up to 1017 cm-3 and 1018 cm-3, respectively, have been measured inside the films. Secondary ion mass spectroscopy results show that most Cd stays inside the ZnCdO film but the diffused atoms can penetrate up to 1.3 μm inside the ZnO buffer. PAS results give an insight to the structure of the meta-stable ZnCdO above the thermodynamical solubility limit of 2%. A correlation between the concentration of vacancy clusters and Cd has been measured. The concentration of Zn vacancies is one order of magnitude larger than in as-grown non-polar ZnO films and the vacancy cluster are, at least partly, created by the aggregation of smaller Zn vacancy related defects. The Zn vacancy related defects and the vacancy clusters accumulate around the Cd atoms as a way to release the strain induced by the substitutional CdZn in the ZnO crystal.

Performance of Dye-Sensitized Solar Cells (DSSCs) Fabricated with Zinc Oxide (ZnO) Nanpowders and Nanorods

Science.gov (United States)

Chatterjee, Suman

2018-03-01

Due to their high efficiencies, along with lower production costs, many researchers are working on dye-sensitized solar cells (DSSCs) over last few decades as a substitute technology for nonconventional energy. Nanostructured ZnO has got many interesting properties such as wide band gap, large exciton binding energy, good exciton stability, and high breakdown strength, which are applicable as DSSC electrodes. This present work compares the device properties of DSSC fabricated using ZnO nanorods on a ZnO film and ZnO nanopowders. Different types of ZnO photoanode and dye combinations are used to study the stability and photovoltaic properties of the DSSC cell. The photovoltaic properties of the ZnO-based DSSC samples were systematically investigated. The photovoltaic properties of fabricated cell obtained are discussed in the light of band structure and density of states of different types of ZnO nanolayers. The ZnO nanorods fabricated through the sol-gel route have more uniform thickness resulting in enhanced photovoltaic properties of the fabricated device.

Vibrational modes of isolated substitution impurities in twelve compounds AN B8-N with the blende structure

International Nuclear Information System (INIS)

Plumelle, Pierre

1979-01-01

We have studied a particular point defect, the isolated substitution in twelve compounds CuCl, CuBr, CuI, ZnTe, CdTe, ZnS, ZnSe, GaAs, GaP, InSb, InP and GaSb. The model of the perfect lattice is a rigid ion model with eleven parameters. Infrared localized vibrational modes of impurities are observed in a series of samples. By comparison of these experimental results with the calculated values it is possible to determine the perturbation for each particular case. A relation obtained between a force constant of the perfect crystal and the force constant of the impurity suggests that no change is introduced by the isoelectronic impurities. (author) [fr

Intrinsic point defects in off-stoichiometric Cu2ZnSnSe4: A neutron diffraction study

Science.gov (United States)

Gurieva, Galina; Valle Rios, Laura Elisa; Franz, Alexandra; Whitfield, Pamela; Schorr, Susan

2018-04-01

This work is an experimental study of intrinsic point defects in off-stoichiometric kesterite type CZTSe by means of neutron powder diffraction. We revealed the existence of copper vacancies (VCu), various cation anti site defects (CuZn, ZnCu, ZnSn, SnZn, and CuZn), as well as interstitials (Cui, Zni) in a wide range of off-stoichiometric polycrystalline powder samples synthesized by the solid state reaction. The results show that the point defects present in off-stoichiometric CZTSe agree with the off-stoichiometry type model, assuming certain cation substitutions accounting for charge balance. In addition to the known off-stoichiometry types A-H, new types (I-L) have been introduced. For the very first time, a correlation between the chemical composition of the CZTSe kesterite type phase and the occurring intrinsic point defects is presented. In addition to the off-stoichiometry type specific defects, the Cu/Zn disorder is always present in the CZTSe phase. In Cu-poor/Zn-rich CZTSe, a composition considered as the one that delivers the best photovoltaic performance, mainly copper vacancies, ZnCu and ZnSn anti sites are present. Also, this compositional region shows the lowest degree of Cu/Zn disorder.

Ferromagnetism in Gd doped ZnO nanowires: A first principles study

Energy Technology Data Exchange (ETDEWEB)

Aravindh, S. Assa; Schwingenschloegl, Udo, E-mail: udo.schwingenschloegl@kaust.edu.sa, E-mail: iman.roqan@kaust.edu.sa; Roqan, Iman S., E-mail: udo.schwingenschloegl@kaust.edu.sa, E-mail: iman.roqan@kaust.edu.sa [Physical Sciences and Engineering Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900 (Saudi Arabia)

2014-12-21

In several experimental studies, room temperature ferromagnetism in Gd-doped ZnO nanostructures has been achieved. However, the mechanism and the origin of the ferromagnetism remain controversial. We investigate the structural, magnetic, and electronic properties of Zn{sub 48}O{sub 48} nanowires doped with Gd, using density functional theory. Our findings indicate that substitutionally incorporated Gd atoms prefer occupying the surface Zn sites. Moreover, the formation energy increases with the distance between Gd atoms, signifying that no Gd-Gd segregation occurs in the nanowires within the concentration limit of ≤2%. Gd induces ferromagnetism in ZnO nanowires with magnetic coupling energy up to 21 meV in the neutral state, which increases with additional electron and O vacancy, revealing the role of carriers in magnetic exchange. The potential for achieving room temperature ferromagnetism and high T{sub C} in ZnO:Gd nanowires is evident from the large ferromagnetic coupling energy (200 meV) obtained with the O vacancy. Density of states shows that Fermi level overlaps with Gd f states with the introduction of O vacancy, indicating the possibility of s-f coupling. These results will assist in understanding experimental findings in Gd-doped ZnO nanowires.

Formation of p-type ZnO thin film through co-implantation

Science.gov (United States)

Chuang, Yao-Teng; Liou, Jhe-Wei; Woon, Wei-Yen

2017-01-01

We present a study on the formation of p-type ZnO thin film through ion implantation. Group V dopants (N, P) with different ionic radii are implanted into chemical vapor deposition grown ZnO thin film on GaN/sapphire substrates prior to thermal activation. It is found that mono-doped ZnO by N+ implantation results in n-type conductivity under thermal activation. Dual-doped ZnO film with a N:P ion implantation dose ratio of 4:1 is found to be p-type under certain thermal activation conditions. Higher p-type activation levels (1019 cm-3) under a wider thermal activation range are found for the N/P dual-doped ZnO film co-implanted by additional oxygen ions. From high resolution x-ray diffraction and x-ray photoelectron spectroscopy it is concluded that the observed p-type conductivities are a result of the promoted formation of PZn-4NO complex defects via the concurrent substitution of nitrogen at oxygen sites and phosphorus at zinc sites. The enhanced solubility and stability of acceptor defects in oxygen co-implanted dual-doped ZnO film are related to the reduction of oxygen vacancy defects at the surface. Our study demonstrates the prospect of the formation of stable p-type ZnO film through co-implantation.

Influence of the applied potentials difference on structural and conductive properties of CoZnO nanotubes

Science.gov (United States)

Ibragimova, M. A.; Kozlovskiy, A. L.; Kenzhina, I. E.; Zdorovets, M. V.

2018-04-01

A series of CoZnO nanotubes was obtained by electrochemical deposition, with different atomic metal coefficients, due to a change in the applied potential difference. A systematic study of the morphology, structural and conductive properties of nanotubes was also carried out. It is established that the samples synthesized at the applied potentials difference of 1.5 and 1.75 V are three-component systems consisting of two oxide phases of ZnO and CoO1.92 cubic system and a phase of a solid solution of substitution Co0.65Zn0.35 of hexagonal type. The samples synthesized at a potential difference of 2.0 V represent an alloy of two oxide phases, ZnO and CoO1.92.

Intermixing at the absorber-buffer layer interface in thin-film solar cells: The electronic effects of point defects in Cu(In,Ga)(Se,S){sub 2} and Cu{sub 2}ZnSn(Se,S){sub 4} devices

Energy Technology Data Exchange (ETDEWEB)

Varley, J. B.; Lordi, V. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

2014-08-14

We investigate point defects in the buffer layers CdS and ZnS that may arise from intermixing with Cu(In,Ga)(S,Se){sub 2} (CIGS) or Cu{sub 2}ZnSn(S,Se){sub 4} (CZTS) absorber layers in thin-film photovoltaics. Using hybrid functional calculations, we characterize the electrical and optical behavior of Cu, In, Ga, Se, Sn, Zn, Na, and K impurities in the buffer. We find that In and Ga substituted on the cation site act as shallow donors in CdS and tend to enhance the prevailing n-type conductivity at the interface facilitated by Cd incorporation in CIGS, whereas they are deep donors in ZnS and will be less effective dopants. Substitutional In and Ga can favorably form complexes with cation vacancies (A-centers) which may contribute to the “red kink” effect observed in some CIGS-based devices. For CZTS absorbers, we find that Zn and Sn defects substituting on the buffer cation site are electrically inactive in n-type buffers and will not supplement the donor doping at the interface as in CIGS/CdS or ZnS devices. Sn may also preferentially incorporate on the S site as a deep acceptor in n-type ZnS, which suggests possible concerns with absorber-related interfacial compensation in CZTS devices with ZnS-derived buffers. Cu, Na, and K impurities are found to all have the same qualitative behavior, most favorably acting as compensating acceptors when substituting on the cation site. Our results suggest one beneficial role of K and Na incorporation in CIGS or CZTS devices is the partial passivation of vacancy-related centers in CdS and ZnS buffers, rendering them less effective interfacial hole traps and recombination centers.

3d-metal doping (Fe,Co,Ni,Zn) of the high T/sub c/ perovskite YBa/sub 2/Cu/sub 3/O/sub 7-y/

International Nuclear Information System (INIS)

Tarascon, J.M.; Barboux, P.; Greene, L.H.; Hull, G.W.; Bagley, B.G.

1988-01-01

The structural, magnetic and superconducting properties of the mixed compounds YBa/sub 2/Cu/sub 3-x/M/sub x/O/sub 7-y/ (M = Ni, Zn, Fe and Co) are reported. Values of y, determined by titration, are found to be dependent on the nature and amount of the doping. The range of solubility is greater for the Fe and Co compounds (chi = 1) than for those with Ni or Zn (chi = 0.3). The undoped material is orthorhombic and remains orthorhombic after substitution for Cu by Ni or Zn, whereas a tetragonal phase is observed when Fe, Co are substituted for Cu. DC resistance and AC susceptibility measurements show that T/sub c/ is depressed from 90K (chi = 0) to 45K (chi = 0.2) for both the Ni and Zn doped compounds and T/sub c/ is destroyed in the Fe and Co doped compounds when chi reaches 0.4. The authors suggest that a valance of 2 be assigned to the Ni and Zn and 3 to the Fe and Co ions

Synthesis and properties of Pr-substituted MgZn ferrites for core materials and high frequency applications

Energy Technology Data Exchange (ETDEWEB)

Mukhtar, Muhammad Waqas; Irfan, Muhammad [Department of Physics, Federal Urdu University of Arts, Science and Technology, Islamabad 44000 (Pakistan); Ahmad, Ishtiaq; Ali, Ihsan [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Akhtar, Majid Niaz [Department of Physics, COMSATS Institute of Information Technology, Lahore (Pakistan); Khan, Muhammad Azhar [Department of Physics, Islamia University, Bahawalpur (Pakistan); Abbas, Ghazanfar [Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan); Rana, M.U. [Center of Excellence in Solid State Physics, University of the Punjab, Lahore (Pakistan); Ali, Akbar [Department of Basic Sciences, Riphah International University, Islamabad-44000 (Pakistan); Ahmad, Mukhtar, E-mail: ahmadmr25@yahoo.com [Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan)

2015-05-01

A series of single phase spinel ferrites having chemical formula Mg{sub 0.5}Zn{sub 0.5}Pr{sub x}Fe{sub 2−x}O{sub 4} (x=0.00, 0.05, 0.10, 0.15, 0.20, 0.25) were prepared using the sol–gel technique after sintering at 700 °C. The thermal decomposition behavior of an as prepared powder was investigated by means of DTA/TGA analyses. The sintered powders were then characterized by Fourier transform infrared spectroscope, X-ray diffraction, scanning electron microscope, energy dispersive X-ray spectroscope and vibrating sample magnetometer. X-ray diffraction patterns confirm the single phase spinel structure of prepared ferrites without the presence of any impurity phase. The value of lattice parameter (a) increases with the increase of Pr contents (x) into the spinel lattice. The grain size estimated from electron microscope images is in the range of 2.75–5.4 µm which confirms the spinel crystalline nature of the investigated samples. The saturation magnetization (M{sub s}) decreases whereas coercivity (H{sub c}) increases with the increase of Pr contents (x). The measured parameters suggest that these materials are favorable for high frequency applications and as core materials. - Highlights: • Pr-substituted spinel ferrites synthesized by autocombustion route have been investigated. • The average grain size was in the range of 2.75–5.4 µm estimated by SEM technique. • The (M{sub s}) decreases whereas (H{sub c}) increases with the increase of Pr contents (x). • These parameters are favorable for high frequency applications and as core materials.

Zinc-Substituted Myoglobin Is a Naturally Occurring Photo-antimicrobial Agent with Potential Applications in Food Decontamination.

Science.gov (United States)

Delcanale, Pietro; Montali, Chiara; Rodríguez-Amigo, Beatriz; Abbruzzetti, Stefania; Bruno, Stefano; Bianchini, Paolo; Diaspro, Alberto; Agut, Montserrat; Nonell, Santi; Viappiani, Cristiano

2016-11-16

Zinc-substituted myoglobin (ZnMb) is a naturally occurring photosensitizer that generates singlet oxygen with a high quantum yield. Using a combination of photophysical and fluorescence imaging techniques, we demonstrate the interaction of ZnMb with Gram-positive Staphylococcus aureus and Gram-negative Escherichia coli. An efficient antibacterial action against S. aureus was observed, with a reduction up to 99.9999% in the number of colony-forming units, whereas no sizable effect was detected against E. coli. Because ZnMb is known to form during the maturation of additive-free not-cooked cured ham, the use of this protein as a built-in photodynamic agent may constitute a viable method for the decontamination of these food products from Gram-positive bacteria.

Effects of Zn additions to highly magnetoelastic FeGa alloys

Energy Technology Data Exchange (ETDEWEB)

Lograsso, Thomas A., E-mail: lograsso@ameslab.gov [Division of Materials Sciences and Engineering, Ames Laboratory, Ames, Iowa 50011 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, Iowa 50011 (United States); Jones, Nicholas J.; Wun-Fogle, Marilyn; Restorff, James B. [Metallurgy and Fasteners Branch, Naval Surface Warfare Center, Carderock Division, Maryland 20817 (United States); Schlagel, Deborah L. [Division of Materials Sciences and Engineering, Ames Laboratory, Ames, Iowa 50011 (United States); Petculescu, Gabriela [University of Louisiana at Lafayette, Louisiana 70504 (United States); Clark, Arthur E. [Clark Associates, Adelphi, Maryland 20783 (United States); Hathaway, Kristl B. [Spectrum Technology Group, Inc., Gaithersburg, Maryland 20877 (United States)

2015-05-07

Fe{sub 1−x}M{sub x} (M = Ga, Ge, Si, Al, Mo and x ∼ 0.18) alloys offer an extraordinary combination of magnetoelasticity and mechanical properties. They are rare-earth-free, can be processed using conventional deformation techniques, have high magnetic permeability, low hysteresis, and low magnetic saturation fields, making them attractive for device applications such as actuators and energy harvesters. Starting with Fe-Ga as a reference and using a rigid-band-filling argument, Zhang et al. predicted that lowering the Fermi level by reducing the total number of electrons could enhance magnetoelasticity. To provide a direct experimental validation for Zhang's hypothesis, elemental additions with lower-than-Ga valence are needed. Of the possible candidates, only Be and Zn have sufficient solubility. Single crystals of bcc Fe-Ga-Zn have been grown with up to 4.6 at. % Zn in a Bridgman furnace under elevated pressure (15 bars) in order to overcome the high vapor pressure of Zn and obtain homogeneous crystals. Single-crystal measurements of magnetostriction and elastic constants allow for the direct comparison of the magnetoelastic coupling constants of Fe-Ga-Zn with those of other magnetoelastic alloys in its class. The partial substitution of Ga with Zn yields values for the magnetoelastic coupling factor, −b{sub 1}, comparable to those of the binary Fe-Ga alloy.

Magnetic and structural properties of Zn-doped yttrium iron garnet nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Pena-Garcia, R.; Delgado, A.; Guerra, Y.; Farias, B.V.M.; Martinez, D. [Pos Graduacao em Ciencia de Materiais, Universidade Federal de Pernambuco, Recife, PE (Brazil); Skovroinski, E. [Departamento de Quimica Fundamental, Universidade Federal de Pernambuco, Recife, PE (Brazil); Galembeck, A. [Pos Graduacao em Ciencia de Materiais, Universidade Federal de Pernambuco, Recife, PE (Brazil); Departamento de Quimica Fundamental, Universidade Federal de Pernambuco, Recife, PE (Brazil); Padron-Hernandez, E. [Pos Graduacao em Ciencia de Materiais, Universidade Federal de Pernambuco, Recife, PE (Brazil); Departamento de Fisica, Universidade Federal de Pernambuco, Recife, PE (Brazil)

2016-09-15

Zn-doped YIG was prepared using the sol-gel method with TGA measurements showing the phase formation between 900 and 1000 C. XRD analysis showed close to 1100 C the formation of Franklinite phase, coexisting with the cubic YIG. Y{sub 3}(Fe{sub 1-x}Zn{sub x}){sub 5}O{sub 12} samples with different Zn concentrations (x = 0, 0.01, 0.03, and 0.05) were prepared and analyzed for a magnetic study. A decrease in magnetic moment of the samples was confirmed on increasing the concentration of Zn ions. This decrease is due to the substitution of Fe ions by Zn. This also confirmed the results of XRD showing the linear increase in the lattice parameter. Fittings by Bloch's law shows results compared with those already reported in the literature. The exponent and constant for the Bloch law presented similar values to those reported for YIG doped with other ions. We obtained the parameter α ∝10{sup -6} K{sup -n} with n close to 1.9 for all samples. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Enhanced photo-electrochemical performances of graphene-based composite functionalized by Zn{sup 2+} tetraphenylporphyrin

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhongqiang [Key Laboratory for Soft Chemistry and Functional Materials, Nanjing University of Science and Technology, Ministry of Education, Nanjing 210094 (China); Zhu, Junwu, E-mail: zhujw@njust.edu.cn [Key Laboratory for Soft Chemistry and Functional Materials, Nanjing University of Science and Technology, Ministry of Education, Nanjing 210094 (China); Han, Qiaofeng [Key Laboratory for Soft Chemistry and Functional Materials, Nanjing University of Science and Technology, Ministry of Education, Nanjing 210094 (China); Cui, Hao [School of Public Administration, Shandong Normal University, Jinan 250014 (China); Bi, Huiping, E-mail: hpbi@njust.edu.cn [Key Laboratory for Soft Chemistry and Functional Materials, Nanjing University of Science and Technology, Ministry of Education, Nanjing 210094 (China); Wang, Xin [Key Laboratory for Soft Chemistry and Functional Materials, Nanjing University of Science and Technology, Ministry of Education, Nanjing 210094 (China)

2014-12-01

Graphical abstract: - Highlights: • With the aid of π–π stacking interaction, the graphene was successfully functionalized by zinc tetraphenylporphyrin. • In obtained G/ZnTPP composite, the ZnTPP and graphene can substitute for porphyrin-like ring structure and electron transport chain, respectively. • Combined with graphene, the G/ZnTPP composite shows a high photo-electrochemical performance. - Abstract: Inspired by the role of electron transport chain in chlorophyll, graphene (G) complexation with zinc 5, 10, 15, 20-tetraphenylporphyrin (ZnTPP) is expected to have excellent photo-electrochemical performances. Here, we design a facile strategy to synthesize the functionalized graphene/zinc tetraphenylporphyrin (G/ZnTPP) composite. In which, all characterizations indicate synergistic effect does exist between graphene sheets and ZnTPP. The synergistic effect enables such composite to possess improved photo-electrochemical behaviors that are key features for photoelectric conversion device. On the basis of this, attempts to modify the absorption range, improve specific capacitance and lower resistance to acquire effective photo-current responses have been successfully demonstrated in this research.

113Cd-NMR investigation of a cadmium-substituted copper, zinc-containing superoxide dismutase from yeast

DEFF Research Database (Denmark)

Kofod, Pauli; Bauer, Rogert; Danielsen, Eva

1991-01-01

113Cd nuclear magnetic resonance spectroscopy has been used to investigate the metal binding sites of cadmium-substituted copper,zinc-containing superoxide dismutase from baker's yeast. NMR signals were obtained for 113Cd(II) at the Cu site as well as for 113Cd(II) at the Zn site. The two subunits...

The Effect of (Ag, Ni, Zn-Addition on the Thermoelectric Properties of Copper Aluminate

Directory of Open Access Journals (Sweden)

Jianxiao Xu

2010-01-01

Full Text Available Polycrystalline bulk copper aluminate Cu1-x-yAgxByAlO2 with B = Ni or Zn were prepared by spark plasma sintering and subsequent thermal treatment. The influence of partial substitution of Ag, Ni and Zn for Cu-sites in CuAlO2 on the high temperature thermoelectric properties has been studied. The addition of Ag and Zn was found to enhance the formation of CuAlO2 phase and to increase the electrical conductivity. The addition of Ag or Ag and Ni on the other hand decreases the electrical conductivity. The highest power factor of 1.26 × 10-4 W/mK2 was obtained for the addition of Ag and Zn at 1,060 K, indicating a significant improvement compared with the non-doped CuAlO2 sample.

Effects of co-dopants on the magnetic properties of Ni–Zn ferrites

Energy Technology Data Exchange (ETDEWEB)

Wang, Sea-Fue, E-mail: sfwang@ntut.edu.tw; Hsu, Yung-Fu; Chou, Kai-Mou; Tsai, Jeng-Ting

2015-01-15

In this study, substitution of co-dopants into the Ni{sub 0.4}Zn{sub 0.6}Fe{sub 2}O{sub 4} ceramic was performed. Al{sup 3+}, Sn{sup 4+} and Ti{sup 4+} ions were added to the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Fe{sub 2.10}O{sub 4} ceramic to improve magnetic properties. After sintering, all samples were indexed on a spinel structure and no detectable second phase was observed. When the concentration of dopants increased, the grain size of the Ni–Zn ferrites increased from 1.40 to 6.05 μm and the saturation magnetization declined from 428.8 emu/cm{sup 3} to 374.0 emu/cm{sup 3}. Amongst the systems investigated, the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4}, Ni{sub 0.4}Zn{sub 0.425}Li{sub 0.10}Ti{sub 0.025}Fe{sub 2.050}O{sub 4}, and Ni{sub 0.4}Zn{sub 0.450}Li{sub 0.10}Ti{sub 0.050}Fe{sub 2.000}O{sub 4} ceramics revealed promising magnetic properties for applications. The measured initial permeability and quality factor were respectively 291.9 and 45.1 for the Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4} ceramic, 316.9 and 42.5 for the Ni{sub 0.4}Zn{sub 0.425}Li{sub 0.10}Ti{sub 0.025}Fe{sub 2.050}O{sub 4} ceramic, 429.4 and 34.8 for the Ni{sub 0.4}Zn{sub 0.450}Li{sub 0.10}Ti{sub 0.050}Fe{sub 2.000}O{sub 4} ceramic. The high initial permeability and quality factor values associated with good electrical resistivity (>10{sup 6} Ω-cm) qualify the ceramics for high frequency applications. - Highlights: • Co-dopants Al{sup 3+}–Li{sup +}, Sn{sup 4+}–Li{sup +}, and Ti{sup 4}–Li{sup +} were substituted into Ni–Zn lattices. • Grain size of Ni–Zn ferrites grew from 1.40 to 6.05 μm with rising dopants content. • Saturation magnetization declined from 428.8 to 374.0 emu/cm{sup 3} with adding dopants. • Ni{sub 0.4}Zn{sub 0.4}Li{sub 0.10}Al{sub 0.050}Fe{sub 2.050}O{sub 4} ceramic showed an μ{sub i} of 291.9 and a Q{sub f} of 45.1.

Synthesis and characterization of heterobinuclear (La-Zn, Pr-Zn, Nd-Zn, Sm-Zn, Eu-Zn, Gd-Zn, Tb-Zn, Dy-Zn) azine-bridged complexes

International Nuclear Information System (INIS)

Singh, Bachcha; Srivastav, A.K.; Singh, P.K.

1997-01-01

Zinc(II) complex of 2-acetylpyridine salicyl aldazine (Haps) of the type Zn(aps) 2 (H 2 O) 2 has been synthesised. The reaction of Zn(aps) 2 (H 2 O) 2 with lanthanide chlorides, LnCl 3 (where Ln=La, Pr, Nd, Sm, Eu, Gd, Tb and Dy) yields azine-bridged heterobinuclear complexes of the formulae LnCl 3 Zn(aps) 2 (H 2 O) 2 . These complexes have been characterized by elemental analyses, molecular weight, conductance (solid and solution) and magnetic susceptibility measurements, mass, IR and electronic spectral data. X-ray powder diffraction data indicate the tetragonal unit lattice for Zn(aps) 2 (H 2 O) 2 and PrCl 3 Zn(aps) 2 (H 2 O) 2 . (author)

Magnetic properties of sol-gel synthesized C-doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Dung, Nguyen Duc, E-mail: dung.nguyenduc@hust.edu.vn [Advanced Institute of Science and Technology (AIST), Hanoi University of Science and Technology, No.1 Dai Co Viet, Hanoi (Viet Nam); Son, Cao Thai; Loc, Pham Vu; Cuong, Nguyen Huu; Kien, Pham The; Huy, Pham Thanh [Advanced Institute of Science and Technology (AIST), Hanoi University of Science and Technology, No.1 Dai Co Viet, Hanoi (Viet Nam); Ha, Ngo Ngoc [International Training Institute for Materials Science (ITIMS), Hanoi University of Science and Technology, No.1 Dai Co Viet, Hanoi (Viet Nam)

2016-05-25

ZnO doping with Carbon (C-doped ZnO) materials were prepared by sol-gel technique following with a heat treatment process. Single phase of Wurtzite crystal structure of ZnO was concluded via x-ray diffraction (XRD) with a large amount of excess C tracking by energy dispersive X-ray spectroscopy (EDX) analysis. Two types of ZnO crystals (twinning particles) with different grain sizes and shapes were identified via scanning electron microscopy (FE-SEM). The first type has a smaller grain size of about 20 nm and hexagonal shape. And the second type has a larger grain size of about 80–120 nm and round shape. C substitutions of both Zn and O sites to form C–O and C–Zn bonds were conclusively confirmed via x-ray photoelectron spectroscope (XPS). Experimental evidences for the co-existence of different ferromagnetic phases in the materials are reported and discussed. Two Curie points at high temperatures (>500 °C) are presented. A metamagnetic transition was observed at magnetic field H = 19.2 kOe which was related to the co-existence of ferromagnetic phases. These involve in the formation of twinning C-doped ZnO nanoparticles. - Highlights: • Formation of sol-gel prepared single phase wurtzite ZnO nanoparticles. • Two morphological C-doped ZnO nanoparticles of different grain sizes. • The room temperature ferromagnetism. • An abnormal metamagnetic transition at magnetic field H = 19.2 kOe. • Two different Curie points (T{sub C}) at 500–600 °C.

Structural and magnetic properties in Mn-doped ZnO films prepared by pulsed-laser deposition

International Nuclear Information System (INIS)

Li, Qiang; Wang, Yuyin; Liu, Jiandang; Kong, Wei; Ye, Bangjiao

2014-01-01

We investigated the structural and magnetic properties of Zn 0.95 Mn 0.05 O films prepared on sapphire substrates by pulsed-laser deposition. Only low temperature ferromagnetism (Curie temperature lower than 50 K) was observed in Mn-doped samples, while pure ZnO film shows a typical paramagnetic behavior. Structural analyses indicate that the substitutional Mn 2+ ions play a significant role for the low temperature ferromagnetism. Lattice defects such as V O and V Zn were not proven to be effective factors for the origin of ferromagnetism in the films. The low temperature ferromagnetism might be interpreted as p–d hybridization from indirect coupling of Mn ions (Mn–O–Mn).

Zn induced in-gap electronic states in La214 probed by uniform magnetic susceptibility: relevance to the suppression of superconducting T c

Science.gov (United States)

Islam, R. S.; Naqib, S. H.

2018-02-01

Substitution of isovalent non-magnetic defects, such as Zn, in the CuO2 plane strongly modifies the magnetic properties of strongly electron correlated hole doped cuprate superconductors. The reason for enhanced uniform magnetic susceptibility, χ, in Zn substituted cuprates is debatable. Generally the defect induced magnetic behavior has been analyzed mainly in terms of two somewhat contrasting scenarios. The first one is due to independent localized moments appearing in the vicinity of Zn arising because of the strong electronic/magnetic correlations present in the host compound and the second one is due to transfer of quasiparticle (QP) spectral weight and creation of weakly localized low-energy electronic states associated with each Zn atom in place of an in-plane Cu. If the second scenario is correct, one should expect a direct correspondence between Zn induced suppression of the superconducting transition temperature, T c, and the extent of the enhanced magnetic susceptibility at low temperature. In this case, the low-T enhancement of χ would be due to weakly localized QP states at low energy and these electronic states will be precluded from taking part in Cooper pairing. We explore this second possibility by analyzing the χ(T) data for La2-x Sr x Cu1-y Zn y O4 with different hole contents, p (=x), and Zn concentrations (y) in this paper. The results of our analysis support this scenario.

Influence of ZnO/MgO substitution on sintering, crystallisation, and bio-activity of alkali-free glass-ceramics

Energy Technology Data Exchange (ETDEWEB)

Kapoor, Saurabh [Department of Materials and Ceramics Engineering, University of Aveiro, CICECO, 3810-193 Aveiro (Portugal); Goel, Ashutosh [Department of Materials Science and Engineering, Rutgers, The State University of New Jersey, Piscataway, NJ 08854-8065 (United States); Correia, Ana Filipa [Department of Materials and Ceramics Engineering, University of Aveiro, CICECO, 3810-193 Aveiro (Portugal); Pascual, Maria J. [Instituto de Cerámica y Vidrio (CSIC), Kelsen 5, Campus de Cantoblanco, 28049 Madrid (Spain); Lee, Hye-Young; Kim, Hae-Won [Institute of Tissue Regeneration Engineering (ITREN) & College of Dentistry, Dankook University, Cheonan 330714 (Korea, Republic of); Department of Nanobiomedical Science & BK21 PLUS NBM Global Research Centre for Regenerative Medicine, Dankook University, Cheonan 330714 (Korea, Republic of); Ferreira, José M.F., E-mail: jmf@ua.pt [Department of Materials and Ceramics Engineering, University of Aveiro, CICECO, 3810-193 Aveiro (Portugal)

2015-08-01

The present study reports on the influence of partial replacement of MgO by ZnO on the structure, crystallisation behaviour and bioactivity of alkali-free bioactive glass-ceramics (GCs). A series of glass compositions (mol%): 36.07 CaO–(19.24 − x) MgO–x ZnO–5.61 P{sub 2}O{sub 5}–38.49 SiO{sub 2}–0.59 CaF{sub 2} (x = 2–10) have been synthesised by melt–quench technique. The structural changes were investigated by solid-state magic angle spinning nuclear magnetic resonance (MAS-NMR), X-ray diffraction and differential thermal analysis. The sintering and crystallisation behaviours of glass powders were studied by hot-stage microscopy and differential thermal analysis, respectively. All the glass compositions exhibited good densification ability resulting in well sintered and mechanically strong GCs. The crystallisation and mechanical behaviour were studied under non-isothermal heating conditions at 850 °C for 1 h. Diopside was the primary crystalline phase in all the GCs followed by fluorapatite and rankinite as secondary phases. Another phase named petedunnite was identified in GCs with ZnO content > 4 mol. The proliferation of mesenchymal stem cells (MSCs) and their alkaline phosphatase activity (ALP) on GCs was revealed to be Zn-dose dependent with the highest performance being observed for 4 mol% ZnO. - Highlights: • The addition of zinc to glasses decreased T{sub g} and promoted crystallisation. • Zinc enhanced the sintering ability and increased mechanical strength by 36%. • The apatite formation ability decreased with increasing Zn contents. • Zinc stimulated mesenchymal stem cell proliferation in a dose dependent manner.

Influence of ZnO/MgO substitution on sintering, crystallisation, and bio-activity of alkali-free glass-ceramics

International Nuclear Information System (INIS)

Kapoor, Saurabh; Goel, Ashutosh; Correia, Ana Filipa; Pascual, Maria J.; Lee, Hye-Young; Kim, Hae-Won; Ferreira, José M.F.

2015-01-01

The present study reports on the influence of partial replacement of MgO by ZnO on the structure, crystallisation behaviour and bioactivity of alkali-free bioactive glass-ceramics (GCs). A series of glass compositions (mol%): 36.07 CaO–(19.24 − x) MgO–x ZnO–5.61 P 2 O 5 –38.49 SiO 2 –0.59 CaF 2 (x = 2–10) have been synthesised by melt–quench technique. The structural changes were investigated by solid-state magic angle spinning nuclear magnetic resonance (MAS-NMR), X-ray diffraction and differential thermal analysis. The sintering and crystallisation behaviours of glass powders were studied by hot-stage microscopy and differential thermal analysis, respectively. All the glass compositions exhibited good densification ability resulting in well sintered and mechanically strong GCs. The crystallisation and mechanical behaviour were studied under non-isothermal heating conditions at 850 °C for 1 h. Diopside was the primary crystalline phase in all the GCs followed by fluorapatite and rankinite as secondary phases. Another phase named petedunnite was identified in GCs with ZnO content > 4 mol. The proliferation of mesenchymal stem cells (MSCs) and their alkaline phosphatase activity (ALP) on GCs was revealed to be Zn-dose dependent with the highest performance being observed for 4 mol% ZnO. - Highlights: • The addition of zinc to glasses decreased T g and promoted crystallisation. • Zinc enhanced the sintering ability and increased mechanical strength by 36%. • The apatite formation ability decreased with increasing Zn contents. • Zinc stimulated mesenchymal stem cell proliferation in a dose dependent manner

Conjugation of E. coli O157:H7 Antibody to CdSe/ZnS Quantum Dots

Directory of Open Access Journals (Sweden)

N. T. Vo

2015-01-01

Full Text Available The conjugation of antibody to semiconductor quantum dots plays a very important role in many applications such as bioimaging, biomarking, and biosensing. In this research, we present some results of highly luminescent core/shell structure CdSe/ZnS on which the E. coli antibody was conjugated. The CdSe core was synthesized successfully with chemical “green” method. For biological applications, the capping surfactant, trioctylphosphine oxide, was substituted by a new one, mercaptopropionic acid (MPA, before the antibody attachment step. Finally, the E. coli antibody was attached to quantum dots CdSe/ZnS. Morphology, structure, and optical properties were investigated with PL, UV-Vis, TEM, and XRD methods. The successful ligand substitution and antibody attachment were confirmed by zeta potential measurement, FTIR spectroscopy, and TEM. The results showed quantum dots size of 2.3 nm, uniform distribution, and high luminescence. CdSe/ZnS core/shell structure had better stability and enhanced the luminescence efficiency up to threefold compared with the core CdSe. MPA ligand shifted the initial hydrophobic quantum dots to hydrophilic ones, which helped to dissolve them in organic solvents and attach the antibody.

Gigantic terahertz magnetochromism via electromagnons in the hexaferrite magnet Ba2Mg2Fe12O22

Science.gov (United States)

Kida, N.; Kumakura, S.; Ishiwata, S.; Taguchi, Y.; Tokura, Y.

2011-02-01

Effects of temperature (6-225 K) and magnetic field (0-7 T) on the low-energy (1.2-5 meV) electrodynamics of the electromagnon, the magnetic resonance driven by the light electric field, have been investigated for a hexaferrite magnet Ba2Mg2Fe12O22 by using terahertz time-domain spectroscopy. We find the gigantic terahertz magnetochromism via electromagnons; the magnetochromic change, as defined by the difference of the absorption intensity with and without magnetic field, exceeds 500% even at 0.6 T. The results arise from the fact that the spectral intensity of the electromagnon critically depends on the magnetic structure. With changing the conical spin structures in terms of the conical angle θ from the proper screw (θ=0°) to the ferrimagnetic (θ=90°) through the conical spin-ordered phases (0°origin of this electromagnon is argued in terms of the exchange-striction mechanism.

Influence of testosterone on the distribution of 65Zn-binding proteins in the prostate and seminal vesicles of rats

International Nuclear Information System (INIS)

Arlt, R.; Foerster, R.; Scherr, F.; Guenther, T.

1977-01-01

65 Zn (7.4 MBq; 200 μCi) was injected intravenously into normal, castrated and castrated, testosteronesubstituted rats. After 1,24 and 48 hours, the distribution of 65 Zn-binding proteins in the 100,000 g supernatant of the prostate and seminal vesicles was investigated by separation on Sephadex G 100. The prostate and seminal vesicles from any one rat showed the same distribution pattern of 65 Zn-proteins. In castrated rats, the incorporation of 65 Zn was, however, 5-6 times lower than in the normal or castrated, testosterone-substituted rats. One hour after the injection, the highest activity of 65 Zn was found in proteins in the molecular weight range above 100,000. After 48 hours the greatest proportion of 65 Zn was present in the protein peak corresponding to 28,000 Daltons. (orig.) 891 AJ [de

Microwave absorbing properties of rare-earth elements substituted W-type barium ferrite

International Nuclear Information System (INIS)

Wang Jing; Zhang Hong; Bai Shuxin; Chen Ke; Zhang Changrui

2007-01-01

W-type barium ferrites Ba(MnZn) 0.3 Co 1.4 R 0.01 Fe 15.99 O 27 with R=Dy, Nd and Pr were prepared by chemical coprecipitation method. Effects of rare-earth elements (RE) substitution on microstructural and electromagnetic properties were analyzed. The results show that a small amount of RE 3+ ions can replace Fe 3+ ions and adjust hyperfine parameters. An obvious increase in natural resonance frequency and high frequency relaxation, and a sharp decrease for complex permittivity have been observed. Furthermore, the matching thickness and the reflection loss (RL) of one-layer ferrite absorber were calculated. It reveals that thin and broad-band can be obtained by RE-substitution. But only when the magnetic moment of RE 3+ is higher than that of Fe 3+ , can substitution be effective for higher RL. Dy-substituted ferrite composite has excellent microwave absorption properties. The frequency (with respect to -10 dB RL) begins from 9.9 GHz, and the bandwidth reaches far more than 8.16 GHz. The peak value is -51.92 dB at a matching thickness of 2.1 mm

Structural and magnetic properties of Tb implanted ZnO single crystals

International Nuclear Information System (INIS)

Zhou Shengqiang; Potzger, K.; Muecklich, A.; Eichhorn, F.; Helm, M.; Skorupa, W.; Fassbender, J.

2008-01-01

ZnO single crystals have been implanted with Tb ions. For an atomic concentration of 1.5%, annealing at 823 K leads to an increase of the saturation magnetization per implanted Tb ion up to 1.8 μ B at room temperature. Structural investigations revealed no secondary phase formation, but the out-diffusion of Tb. No significant evidence is found for Tb substituting Zn sites either in the as-implanted or annealed samples. However, indications for the existence of a small amount of Tb nanoclusters however have been found using magnetization versus temperature measurements. The ferromagnetic properties disappear completely upon annealing at 1023 K. This behavior is related to the formation of oxide complexes or nanoparticles

Optical and structural properties of individual Co-doped ZnO microwires

Science.gov (United States)

Kolomys, O. F.; Strelchuk, V. V.; Rarata, S. V.; Hayn, R.; Savoyant, A.; Giovannelli, F.; Delorme, F.; Tkach, V.

2018-06-01

The Co-doped ZnO microwires (MWs) were grown using the optical furnace method. We used Scanning electron microscopy (SEM), polarized micro-Raman spectroscopy, photoluminescence (PL) and optical absorption spectroscopy to systematic investigation of the optical and structural properties of Co-doped ZnO MWs. The SEM analysis reveals that Co-doped ZnO MWs has hexagonal facets and cavity inside. The EDS results confirmed the presence and non-uniform distribution of Co impurities in the samples. Co doping of ZnO MWs leads to the decreased intensity, drastically broadening and high-energy shift of the NBE PL band. The red emission band at 1.85 eV originates from 2E(2G) → 4A2 (4F) intra-3d-transition of Co2+ in the ZnO lattice has been observed. The intense structured absorption bands within the near infrared ranges 3800-4800 and 5500-9000 cm-1 are caused by electronic spin-allowed transitions 4T2(F) ← 4A2(F) and 4T1(F) ← 4A2(F) of the tetrahedrally coordinated Co2+ (3 d7) ions substituting Zn2+ ions in Co-doped ZnO MWs. Micro-Raman studies of Co doped ZnO MWs show doping/disorder induced additional modes as compared to the undoped sample. The resonant enhancement of the additional local Co-related A1-symmetry Raman mode is observed in the parallel polarization geometry y(z , z) ybar . For the Co doped ZnO MWs, the enhancement of the additional Co-related local vibration mode with an increase in the excitation photon energy is also observed in the Raman spectra.

First-principles study on ferromagnetism in double perovskite Sr2AlTaO6 doped with Cu or Zn at B sites

Science.gov (United States)

Li, Y. D.; Wang, C. C.; Guo, Y. M.; Yu, Y.; Lu, Q. L.; Huang, S. G.; Li, Q. J.; Wang, H.; Cheng, R. L.; Liu, C. S.

2018-05-01

The possibilities of ferromagnetism induced by nonmagnetic dopants (Cu, Zn) in double perovskite Sr2AlTaO6 at B sites are investigated by density functional theory. Calculations reveal that substitutions at Ta-site tend to form high spin electronic configurations and could induce ferromagnetism which can be attributed to the hole-mediated p- d hybridization between Cu (or Zn) eg states and the neighboring O 2p states. The dopants preferably substitute at Al-site and adopt low spin electronic structures. Due to the smaller hole concentration and weaker covalent intensity, Sr2AlTaO6 with dopants at Al-site exhibits p-type metallic semiconductors without spin polarization.

Suppression of Red Luminescence in Wire Explosion Derived Eu:ZnO

Science.gov (United States)

Pallavi, Bandi; Sathyan, Sneha; Yoshimura, Takuya; Kumar, Praveen; Anbalagan, Kousika; Talluri, Bhusankar; Ramanujam, Sarathi; Ranjan, Prem; Thomas, Tiju

2018-03-01

Europium oxide (Eu2O3) is coated on zinc (Zn) wire using the electrophoretic deposition process. The coated Zn wire is subjected to the wire explosion process (WEP) which is rapid (material has ˜ 0.24 at.% doping. This analysis also shows that, unlike another popular material GaN, in the case of ZnO, Eu3+ strictly substitutes for Zn2+ (i.e., dopant replacing a cation-anion pair does not seem possible). It may be noted that Eu3+ in a suitable host is oftentimes reported to be an efficient luminophore. The IR spectra show a band shift from 486 cm-1 to 493 cm-1; with peak shifts from 436 cm-1 to 430 cm-1 in Raman spectra. These too indicate the presence of Eu in the samples. However, at room temperature, only green luminescence (centered at 534 nm) is observed from the sample indicating (1) high concentrations of OZn anti-site defects and Zn vacancies, and (2) concomitant quenching of the luminescence at room temperature. Our results suggest that WEP is viable for synthesizing rare earth doped ceramic materials. However, obtaining efficient phosphors using this approach will likely require, (1) reduction of defect densities, and (2) appropriate passivation using post-processing.

Nonempirical investigations of the structure and stability of complex boro- and alumohydrides of K, Ca, Cu and Zn

International Nuclear Information System (INIS)

Musaev, D.G.; Charkin, O.P.

1991-01-01

Using nonempirical MO LCAO SCF method the structural and relative energy characteristics of boro- and alumohydrides of alternative configurations, CuAlH 4 , ZnBH 4 + , ZnAlH 4 + and HZnAlH 4 , were calculated. Differences and similarities in the properties of identical boro- and alumohydrides, as well as L 1 MH 4 , HL 2 MH 4 and L 2 MH 4 + molecules with the change of cation in the series K + -HCa + -Ca 2+ and Cu + -HZn + -Zn 2+ on the one hand, and with Cu and Zn substitution for K and Ca on the other hand, were considered. It was shown that alumohydrides of electropositive alkali and alkaline-earth cations K and Ca are less, and those of transition metals Cu and Zn are more hard to cation migration around AlH 4 - and BH 4 - anions than borohydrides

First-principles study on stability and magnetism of AlnZn (n=1-9) clusters

International Nuclear Information System (INIS)

Ren Xiaojun; Li Baoxing

2010-01-01

We have investigated the structures, stabilities and magnetism of zinc-doped Al n (n=1-9) clusters in detail by using first-principles density functional theory. Our calculated results indicate that the ground state structures of the mixed Al n Zn (n=1-9) clusters doped with one zinc atom can be obtained from the most stable structures of the pure Al n (n=2-10) clusters by substitutional type. The impurity atom causes local structural distortion due to different atomic radii and different bonding characteristics. It is found that the clusters with total atom numbers of 3 and 7 exhibit high stability. In addition, the energy gaps E g s between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO) show obvious even/odd alternation with cluster size. Furthermore, we investigate the magnetism of the mixed clusters. The Al 4 Zn, Al 6 Zn and Al 8 Zn clusters with even number of electrons do not have any magnetism. All Al 1 Zn, Al 5 Zn, Al 7 Zn and Al 9 Zn clusters have the total magnetic moment of 1.0 μ B due to one unpaired electron. Unexpectedly, the Al 2 Zn and Al 3 Zn clusters show total magnetic moments of 2.0 and 3.0 μ B , respectively. The magnetism arises from the sp-d hybridization due to charge transfer and the influence of the impurity zinc atom.

The origin of room temperature ferromagnetism mediated by Co–VZn complexes in the ZnO grain boundary

KAUST Repository

Devi, Assa Aravindh Sasikala; Roqan, Iman S.

2016-01-01

Ferromagnetism in polycrystalline ZnO doped with Co has been observed to be sustainable in recent experiments. We use first-principle calculations to show that Co impurities favorably substitute at the grain boundary (GB) rather than in the bulk. We

Study of the influence of ZnO addition on the properties of chitosan-banana starch bioplastics

Science.gov (United States)

Sapei, L.; Padmawijaya, K. S.; Sijayanti, O.; Wardhana, P. J.

2017-07-01

Plastics have been widely used in our daily life due to their relatively low cost and practical uses. However, plastics are hardly degraded and thus creating lots of environmental problems. Bioplastics have been developed in order to replace the conventional plastics since they are easily degraded and environmentally friendly. In this research, chitosan-banana starch bioplastics were made with the ratio of 70:30 in the presence of 30% glycerol as the plasticizer. ZnO with varying concentrations of 1, 3, and 5% were added into the biopolymer mixtures before casting in order to improve their mechanical properties. It turned out that 3% ZnO significantly increased the bioplastics tensile strength up to ~36MPa. Vice versa, elongation and swelling percentage were decreased as ZnO concentrations increased. Bioplastics prepared with 3% ZnO were degraded within relatively short time in 90 min. These chitosan-banana starch bioplastics reinforced by ZnO seems quite promising to substitute some commercial conventional plastics.

Study of substitution in the systems UNi5sub(-)sub(x)Msub(x) and ZrNi5sub(-)sub(x)Msub(x) (M = In, Sn, Zn)

International Nuclear Information System (INIS)

Blazina, Z.; Drasner, A.; Ban, Z.; Zagreb Univ.

1981-01-01

X-ray powder diffraction studies and metallographic examinations in the systems UNi 5 sub(-)sub(x)Msub(x) and ZrNi 5 sub(-)sub(x)Msub(x) (M = In, Sn, Zn) revealed the existence of single phase regions up to the composition 1 : 4 : 1, i.e. up to UNi 4 M and ZrNi 4 M, respectively. Comparison between calculated and observed intensity values showed that nickel atoms, in the crystallographic positions 4(c) of the isostructural binary compounds UNi 5 or ZrNi 5 (UNi 5 -type, S.G. F43m), are substituted by M atoms. Vegard's rule is obeyed in the single phase regions of all investigated systems. The crystal structures of UNi 4 M and ZrNi 4 M are superlattice structures of the MgSnCu 4 -type (S.G. F43m). Structural correlations of these phases with corresponding binary prototypes are made in terms of stacking sequences. (orig.)

Effect of the Low-Temperature Annealing on Zn-Doped Indium-Tin-Oxide Films for Silicon Heterojunction Solar Cells

Science.gov (United States)

Lee, Seunghun; Lee, Jong-Han; Tark, Sung Ju; Choi, Suyoung; Kim, Chan Seok; Lee, Jeong Chul; Kim, Won Mok; Kim, Donghwan

2012-10-01

The effects of the low-temperature annealing on Zn-doped indium-tin-oxide (ITO) films such as the electrical, optical and structural properties were investigated. Zn-doped ITO films were fabricated by rf magnetron sputtering of ITO and Al-doped ZnO (AZO) targets on corning glass at room temperature. The content of Zn increased with increasing the power of AZO target. The carrier concentration of films shows the decreasing behaviour with increasing the content of Zn, due to a carrier compensation originating from the substitution of a doped Zn for an In or interstitial site. After the low-temperature annealing at 180 °C in vacuum, all films were slightly decreased a carrier concentration and increased the hall mobility because of the absorption of oxygen on the surface films. In addition, the average transmittance did not show a considerable change and had a high values over 80%. Especially, the Zn-doped ITO with atomic ratio of Zn/(In+Zn) of 6.8 at. % had the resistivity of 4×10-4 Ω cm, the highest hall mobility of 41 cm2 V-1 s-1, and the average transmittance of 82%.

Distribution and Substitution Mechanism of Ge in a Ge-(Fe-Bearing Sphalerite

Directory of Open Access Journals (Sweden)

Nigel J. Cook

2015-03-01

Full Text Available The distribution and substitution mechanism of Ge in the Ge-rich sphalerite from the Tres Marias Zn deposit, Mexico, was studied using a combination of techniques at μm- to atomic scales. Trace element mapping by Laser Ablation Inductively Coupled Mass Spectrometry shows that Ge is enriched in the same bands as Fe, and that Ge-rich sphalerite also contains measurable levels of several other minor elements, including As, Pb and Tl. Micron- to nanoscale heterogeneity in the sample, both textural and compositional, is revealed by investigation using Focused Ion Beam-Scanning Electron Microscopy (FIB-SEM combined with Synchrotron X-ray Fluorescence mapping and High-Resolution Transmission Electron Microscopy imaging of FIB-prepared samples. Results show that Ge is preferentially incorporated within Fe-rich sphalerite with textural complexity finer than that of the microbeam used for the X-ray Absorption Near Edge Structure (XANES measurements. Such heterogeneity, expressed as intergrowths between 3C sphalerite and 2H wurtzite on  zones, could be the result of either a primary growth process, or alternatively, polystage crystallization, in which early Fe-Ge-rich sphalerite is partially replaced by Fe-Ge-poor wurtzite. FIB-SEM imaging shows evidence for replacement supporting the latter. Transformation of sphalerite into wurtzite is promoted by (111* twinning or lattice-scale defects, leading to a heterogeneous ZnS sample, in which the dominant component, sphalerite, can host up to ~20% wurtzite. Ge K-edge XANES spectra for this sphalerite are identical to those of the germanite and argyrodite standards and the synthetic chalcogenide glasses GeS2 and GeSe2, indicating the Ge formally exists in the tetravalent form in this sphalerite. Fe K-edge XANES spectra for the same sample indicate that Fe is present mainly as Fe2+, and Cu K-edge XANES spectra are characteristic for Cu+. Since there is no evidence for coupled substitution involving a monovalent

Compositional and structural properties of pulsed laser-deposited ZnS:Cr films

Science.gov (United States)

Nematollahi, Mohammadreza; Yang, Xiaodong; Seim, Eivind; Vullum, Per Erik; Holmestad, Randi; Gibson, Ursula J.; Reenaas, Turid W.

2016-02-01

We present the properties of Cr-doped zinc sulfide (ZnS:Cr) films deposited on Si(100) by pulsed laser deposition. The films are studied for solar cell applications, and to obtain a high absorption, a high Cr content (2.0-5.0 at.%) is used. It is determined by energy-dispersive X-ray spectroscopy that Cr is relatively uniformly distributed, and that local Cr increases correspond to Zn decreases. The results indicate that most Cr atoms substitute Zn sites. Consistently, electron energy loss and X-ray photoelectron spectroscopy showed that the films contain mainly Cr2+ ions. Structural analysis showed that the films are polycrystalline and textured. The films with ~4 % Cr are mainly grown along the hexagonal [001] direction in wurtzite phase. The average lateral grain size decreases with increasing Cr content, and at a given Cr content, increases with increasing growth temperature.

Evaluation of methods for available Zn in four soil orders in Costa Rica

International Nuclear Information System (INIS)

Molina, E.; Bornemisza, E.

2001-01-01

Analytical methods for available Zn determination were evaluated on four soil orders in Costa Rica (Ultisols, Vertisols, Inceptisols and Andisols) with 25 samples for each; using the following extract solutions : Modified Olsen, Mehlich 3, Modified Morgan , DTPA and HCI. The Zn levels obtained depended on the chemical characteristics of the extracting solutions. The highest levels were obtained with HCI, except for the Vertisols. The solutions with EDTA (Modified Olsen and Mehlich 3), extracted intermediate levels of Zn, while the method using DTPA (Modified Morgan and DTPA) gave the lowest Zn values . In most of the cases, significant values of correlation were obtained between the 5 extraction methods; so for individual soil orders, or comparing all 100 soils. The highest correlation coefficients for extractable Zn were found for the Mehlich 3, Modified Morgan and DTPA. The correlations were consistent for the 4 orders, which indicate that they are adaptable to different soils, a useful characteristic for these methods. The Modified Olsen was the most efficient extractor in slightly acis soils (Vertisols and Inceptisols). The HCI extracted very high Zn levels, which are probably not related to plant available forms. It is concluded that the Mehlich 3, Modified Morgan and DTPA solutions are probably adequate for available Zn determination and might present an alternative to substitute the generally used Modified Olsen solution in Costa Rica. (Author) [es

Microstructural characterization of chemical bath deposited and sputtered Zn(O,S) buffer layers

International Nuclear Information System (INIS)

Gautron, E.; Buffière, M.; Harel, S.; Assmann, L.; Arzel, L.; Brohan, L.; Kessler, J.; Barreau, N.

2013-01-01

The present work aims at investigating the microstructure of Zn(O,S) buffer layers relative to their deposition route, namely either chemical bath deposition (CBD) or RF co-sputtering process (PVD) under pure Ar. The core of the study consists of cross-sectional transmission electron microscopy (TEM) characterization of the differently grown Zn(O,S) thin films on co-evaporated Cu(In,Ga)Se 2 (CIGSe) absorbers. It shows that the morphology of Zn(O,S) layer deposited on CIGSe using CBD process is made of a thin layer of well oriented ZnS sphalerite-(111) and/or ZnS wurtzite-(0002) planes parallel to CIGSe chalcopyrite-(112) planes at the interface with CIGSe followed by misoriented nanometer-sized ZnS crystallites in an amorphous phase. As far as (PVD)Zn(O,S) is concerned, the TEM analyses reveal two different microstructures depending on the S-content in the films: for [S] / ([O] + [S]) = 0.6, the buffer layer is made of ZnO zincite and ZnS wurtzite crystallites grown nearly coherently to each other, with (0002) planes nearly parallel with CIGSe-(112) planes, while for [S] / ([O] + [S]) = 0.3, it is made of ZnO zincite type crystals with O atoms substituted by S atoms, with (0002) planes perfectly aligned with CIGSe-(112) planes. Such microstructural differences can explain why photovoltaic performances are dependent on the Zn(O,S) buffer layer deposition route. - Highlights: ► Zn(O,S) layers were grown by chemical bath (CBD) or physical vapor (PVD) deposition. ► For CBD, a 3 nm ZnS layer is followed by ZnS nano-crystallites in an amorphous phase. ► For PVD with [S] / ([O] + [S]) = 0.3, the layer has a Zn(O,S) zincite structure. ► For PVD with [S] / ([O] + [S]) = 0.6, ZnS wurtzite and ZnO zincite phases are mixed

Preparation and investigation of structural, magnetic and microwave absorption properties of cerium doped barium hexaferrite

Directory of Open Access Journals (Sweden)

P Kameli

2015-01-01

Full Text Available In this study the structure, magnetic and microwave absorption properties of cerium (Ce doped barium hexaferrite with general formulae BaCexFe12-xO19 (x=0.0, 0.05, 0.1, 0.15, 0.2 have been investigated. These samples have been prepared by sol- gel method. Influence of replacing Fe+3 ion by rare- earth Ce+3 ion on the structural, magnetic and microwave absorption properties have been investigated by X- ray diffraction (XRD, Fourier transform infrared (FT-IR, Vibrating sample magnetometer (VSM and vector network analyzer (VNA. X-ray diffraction analysis indicated that the samples are of single phase with space group p63/mmc. The magnetic properties of samples indicated that with the Ce doping the saturation magnetization show no regular behavior. Moreover, coercivity (Hc first decreased and reached to the minimum value for x=0.1 sample and then increased with Ce content increasing. Also, measurement of electromagnetic wave absorption in X and Ku frequency bands indicated that the maximum of reflection loss obtained for x=0.15 sample. Moreover, result indicated that absorption peak shifted toward a lower frequency when thickness was increased.

Two-dimensional electron gases in MgZnO/ZnO and ZnO/MgZnO/ZnO heterostructures grown by dual ion beam sputtering

Science.gov (United States)

Singh, Rohit; Arif Khan, Md; Sharma, Pankaj; Than Htay, Myo; Kranti, Abhinav; Mukherjee, Shaibal

2018-04-01

This work reports on the formation of high-density (~1013-1014 cm-2) two-dimensional electron gas (2DEG) in ZnO-based heterostructures, grown by a dual ion beam sputtering system. We probe 2DEG in bilayer MgZnO/ZnO and capped ZnO/MgZnO/ZnO heterostructures utilizing MgZnO barrier layers with varying thickness and Mg content. The effect of the ZnO cap layer thickness on the ZnO/MgZnO/ZnO heterostructure is also studied. Hall measurements demonstrate that the addition of a 5 nm ZnO cap layer results in an enhancement of the 2DEG density by about 1.5 times compared to 1.11 × 1014 cm-2 for the uncapped bilayer heterostructure with the same 30 nm barrier thickness and 30 at.% Mg composition in the barrier layer. From the low-temperature Hall measurement, the sheet carrier concentration and mobility are both found to be independent of the temperature. The capacitance-voltage measurement suggests a carrier density of ~1020 cm-3, confined in 2DEG at the MgZnO/ZnO heterointerface. The results presented are significant for the optimization of 2DEG for the eventual realization of cost-effective and large-area MgZnO/ZnO-based high-electron-mobility transistors.

Cation Substitution in Earth‐Abundant Kesterite Photovoltaic Materials

Science.gov (United States)

Li, Jianjun; Wang, Dongxiao; Li, Xiuling; Zeng, Yu

2018-01-01

Abstract As a promising candidate for low‐cost and environmentally friendly thin‐film photovoltaics, the emerging kesterite‐based Cu2ZnSn(S,Se)4 (CZTSSe) solar cells have experienced rapid advances over the past decade. However, the record efficiency of CZTSSe solar cells (12.6%) is still significantly lower than those of its predecessors Cu(In,Ga)Se2 (CIGS) and CdTe thin‐film solar cells. This record has remained for several years. The main obstacle for this stagnation is unanimously attributed to the large open‐circuit voltage (V OC) deficit. In addition to cation disordering and the associated band tailing, unpassivated interface defects and undesirable energy band alignment are two other culprits that account for the large V OC deficit in kesterite solar cells. To capture the great potential of kesterite solar cells as prospective earth‐abundant photovoltaic technology, current research focuses on cation substitution for CZTSSe‐based materials. The aim here is to examine recent efforts to overcome the V OC limit of kesterite solar cells by cation substitution and to further illuminate several emerging prospective strategies, including: i) suppressing the cation disordering by distant isoelectronic cation substitution, ii) optimizing the junction band alignment and constructing a graded bandgap in absorber, and iii) engineering the interface defects and enhancing the junction band bending. PMID:29721421

Cation Substitution in Earth-Abundant Kesterite Photovoltaic Materials.

Science.gov (United States)

Li, Jianjun; Wang, Dongxiao; Li, Xiuling; Zeng, Yu; Zhang, Yi

2018-04-01

As a promising candidate for low-cost and environmentally friendly thin-film photovoltaics, the emerging kesterite-based Cu 2 ZnSn(S,Se) 4 (CZTSSe) solar cells have experienced rapid advances over the past decade. However, the record efficiency of CZTSSe solar cells (12.6%) is still significantly lower than those of its predecessors Cu(In,Ga)Se 2 (CIGS) and CdTe thin-film solar cells. This record has remained for several years. The main obstacle for this stagnation is unanimously attributed to the large open-circuit voltage ( V OC ) deficit. In addition to cation disordering and the associated band tailing, unpassivated interface defects and undesirable energy band alignment are two other culprits that account for the large V OC deficit in kesterite solar cells. To capture the great potential of kesterite solar cells as prospective earth-abundant photovoltaic technology, current research focuses on cation substitution for CZTSSe-based materials. The aim here is to examine recent efforts to overcome the V OC limit of kesterite solar cells by cation substitution and to further illuminate several emerging prospective strategies, including: i) suppressing the cation disordering by distant isoelectronic cation substitution, ii) optimizing the junction band alignment and constructing a graded bandgap in absorber, and iii) engineering the interface defects and enhancing the junction band bending.

Effects of Gd-Substitutions on the Microstructure, Electrical and Electromagnetic Behavior of M-Type Hexagonal Ferrites

Science.gov (United States)

Ahmad, Ishtiaq; Ahmad, Mahmood; Ali, Ihsan; Kanwal, M.; Awan, M. S.; Mustafa, Ghulam; Ahmad, Mukhtar

2015-07-01

A series of Gd-substituted Ba-Co-based (M-type) hexaferrites having the chemical compositions of Ba0.5Co0.5Gd x Fe12- x O19 ( x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0) were prepared by co-precipitation method. The pellets formed by co-precipitated powder were calcined at a temperature of 1200°C for 20 h. Final sintering was done at 1320°C for 4 h. From the x-ray diffraction analysis, it was revealed that all the samples showed M-type hexagonal structure as a major phase. The scanning electron microscope was used to examine the morphology of the sintered ferrites. The average grain size estimated by the line intercept method was found to be in the range of 2.8-1.0 μm. The room temperature DC resistivity increases with increasing Gd-contents to make these ferrites useful for high frequency applications and microwave devices. Lower values of coercivity ( H c) and higher saturation magnetization ( M s) may be suitable to enhance the permeability of these ferrites, which is favorable for impedance matching in microwave absorption. In addition, reflection coefficients for a sample was also measured from a frequency of 1 MHz to 3 GHz and a reflection peak was observed at about 2.2 GHz.

Modulating the electronic properties of asymmetric push–pull and symmetric Zn(II)-diarylporphyrinates with para substituted phenylethynyl moieties in 5,15 meso positions: A combined electrochemical and spectroscopic investigation

International Nuclear Information System (INIS)

Mussini, Patrizia Romana; Orbelli Biroli, Alessio; Tessore, Francesca; Pizzotti, Maddalena; Biaggi, Cinzia; Di Carlo, Gabriele; Lobello, Maria Grazia; De Angelis, Filippo

2012-01-01

Graphical abstract: - Abstract: Push–pull Zn(II)-porphyrinates have recently shown attracting performances as light harvesting systems in dye-sensitized solar cells (DSSCs). To fully exploit their intrinsically high efficiency it is important to finely tune their HOMO and LUMO levels, which can be achieved by proper choice of the push and pull substituents. Of course such target-oriented molecular design requires the availability of reliable relationships between molecular structure and electronic properties; therefore we have carried out a combined electrochemical, spectroscopic and computational investigation on a wide, systematic range of Zn(II)-porphyrinates 5,15 meso substituted with phenylethynyl linkers, including a first symmetric series carrying on the opposite terminals the same substituent (-N(CH 3 ) 2 , -OCH 3 , -COOCH 3 , -COOH, -NO 2 ); and a second push–pull one, with the terminal positions carrying one donor and one acceptor group belonging to the series above. Moreover, two suitably modified porphyrins allowed evaluation of the effects of (i) the presence or absence of the phenyl group in the linker between the porphyrin core and the acceptor group, and (ii) the effect of perfluorination on the same phenyl group. A rationalization scheme is proposed encompassing the whole porphyrin set, affording inter alia interesting clues on the different localization of the redox centres and effective conjugation between the porphyrin core and the side chains as a function of the molecular design.

Dual ferroic properties of hexagonal ferrite ceramics BaFe_1_2O_1_9 and SrFe_1_2O_1_9

International Nuclear Information System (INIS)

Kostishyn, V.G.; Panina, L.V.; Timofeev, A.V.; Kozhitov, L.V.; Kovalev, A.N.; Zyuzin, A.K.

2016-01-01

Dual ferroic properties of a strong magnetism and large ferroelectricity have been observed in barium BaFe_1_2O_1_9 and strontium SrFe_1_2O_1_9 hexaferrite ceramics. The samples were fabricated by a modified ceramic technique from highly purified raw materials with addition of boron oxide allowing the control of grain size and enhancement of bulk resistivity. Whereas the samples of PbFe_1_2O_1_9 fabricated by the same technological method did not have sufficient electric resistivity to support an electric field and did not exhibit the ferroelectric properties. The structure of the samples examined by X-ray diffraction is consistent with a single hexagonal phase. The grains are randomly oriented with the average grain size of 300–400 nm coated with boron oxide. The magnetic properties are characterised by standard ferrimagnetic behavior with the Neel temperature of about 450 °C. Large spontaneous polarization was observed with the maximal values of 45–50 μC/cm"2 under an applied electric field of 100–300 kV/m. A strong coupling between magnetic and electric ordering was confirmed by measuring the magnetoelectric (ME) parameter and magnetodielectric ratio. These ME characteristics are more advanced than those for well-known room temperature multiferroic BiFeO_3. Furthermore, by applying an electric field, the manipulation of magnetization in the range of up to 9% was observed, which is even greater than in some substituted hexaferrites with a non-collinear magnetic structure. The obtained results on electrical polarization are similar to the values reported for the corresponding hexaferrites sintered by polymer precursor technique. This suggests a promising potential of M-type hexaferrite ceramics in devices utilizing magnetoelectric coupling. - Highlights: • Ba(Sr)Fe_1_2O_1_9-hexaferrites show large room-temperature multiferroic properties. • Small addition of B_2O_3 increases the hexaferrite resistivity by 4 orders of magnitude. • Large spontaneous

Hierarchical ZnO microspheres built by sheet-like network: Large-scale synthesis and structurally enhanced catalytic performances

International Nuclear Information System (INIS)

Zhu Guoxing; Liu Yuanjun; Ji Zhenyuan; Bai Song; Shen Xiaoping; Xu Zheng

2012-01-01

Highlights: ► Hierarchical ZnO microspheres were prepared through a facile precursor procedure in the absence of self-assembled templates, organic additives, or matrices. ► The building blocks of microspheres, sheet-like ZnO networks, are porous mesocrystal terminated with (0 1 −1 0) crystal planes. ► The hierarchical ZnO microsphere catalyst exhibits structure-induced enhancement of catalytic performance and a strong durability. - Abstract: Large-scale novel hierarchical ZnO microspheres were fabricated by a facile precursor procedure in the absence of self-assembled templates, organic additives, or matrices. A field emission scanning electron microscopy (FESEM) image reveals that the ZnO microspheres with diameter of 5–18 μm are built by sheet-like ZnO networks with average thickness of 40 nm and length of several microns. High resolution transmission electron microscopy (HRTEM) image indicates that the building blocks, sheet-like ZnO networks, are porous mesocrystal terminated with {0 1 −1 0} crystal planes. A potential application of the ZnO microspheres as a catalyst in the synthesis of 5-substituted 1H-tetrazoles was investigated. It was found that the hierarchical ZnO microsphere catalyst exhibits structure-induced enhancement of catalytic performance and a strong durability.

ZnMoO4:Er3+,Yb3+ phosphor with controlled morphology and enhanced upconversion through alkali ions doping

Science.gov (United States)

Luitel, Hom Nath; Chand, Rumi; Watari, Takanori

2018-04-01

A facile hydrothermal method was used to synthesize ZnMoO4:Er3+,Yb3+ nanoparticles. The shapes and sizes of the nanoparticles were well tuned by simply monitoring the pH of the starting solution. Microballs consisting of agglomerated nanograins were observed at strong acidic condition. At mild pH, plates and rectangular particles were realized, while strong basic pH stabilized rods. Further increasing pH to extremely basic conditions (pH > 13), rods changed to fragile hairy structures. The nucleation and growth mechanism of nanograins to form different morphology nanoparticles were studied and illustrated. XRD patterns confirmed well crystalline, triclinic structure despite small amount of aliovalent metal ions doping. Under 980 nm excitation, the ZnMoO4:Er3+,Yb3+ nanophosphor exhibited strong green (centered at 530 and 560 nm) and weak red (centered at 660 nm) upconversion (UC) emissions. Substitution of part of the Zn2+ ions by monovalent alkali ions intensified the UC emission intensities drastically. The order of intensification was K+>Na+>Li+>Rb+>no alkali ion. When Zn2+ ions were substituted with 10 at% K+ ions, the green and red UC emissions intensities increased by more than 50 and 15 folds, respectively. Time dependent measurements confirmed efficient Yb to Er energy transfer in the ZnMoO4:Er3+,Yb3+,K+ nanophosphor. The optimized ZnMoO4:Er3+,Yb3+,K+ phosphor exhibited intense UC emissions with 0.31% quantum yield. The upconverted light is visible to naked eye while pumping by laser of less than 1 mW power and opens door for variety of novel applications.

Fabrication of Al doped ZnO films using atmospheric pressure cold plasma

International Nuclear Information System (INIS)

Suzaki, Yoshifumi; Miyagawa, Hayato; Yamaguchi, Kenzo; Kim, Yoon-Kee

2012-01-01

Under atmospheric pressure, homogeneous non-equilibrium cold plasma was generated stably by high voltage pulsed power (1 kV, 20 kHz, 38 W) excitation of a mixture of He and O 2 gases produced by a dielectric barrier discharge setup. By feeding Bis (2 methoxy‐6-methyl‐3, 5-heptanedione) Zn (Zn-MOPD, C 18 H 3 O 6 Zn) and Tris (2-methoxy‐6‐methy l‐3, 5-heptanedione) Al (Al-MOPD, C 27 H 45 O 9 Al) into this plasma with He carrier gas, transparent flat Al-doped ZnO (ZnO:Al) films about 120–240 nm thick were prepared on glass substrates directly under the slit made into the cathode. Deposition rates of the films were about 20–40 nm/min. The concentration of Al was measured by inductively coupled plasma atomic emission spectroscopy. The composition ratio of Al to Zn was 7.8 mol% when the carrier He gas flow rate of Al-MOPD was 30 cm 3 . The average transmittance of all films was more than 85% in the wavelength range from 400 to 800 nm. When the composition ratio of Al/Zn was between 1.1 and 7.8 mol%, the optical band gap of the film increased from 3.28 to 3.40 eV. The resistivity of ZnO:Al film was 2.96 Ω cm at 1.3 mol% of Al/Zn. In addition, the microstructure of the films was studied by X-ray diffraction measurement and field emission scanning electron microscope observation. It was revealed that doped Al is substituted onto the Zn site of the ZnO crystalline structure in ZnO:Al films. - Highlights: ► An atmospheric pressure cold plasma generator generated stable glow discharge. ► We fabricated Al doped ZnO films on glass substrates using cold plasma. ► Al concentration measured by inductively coupled plasma atomic emission spectroscopy. ► The transmission spectrum and the resistivity of the films were measured. ► The microstructure of the films was studied.

XPS and DFT study of pulsed Bi-implantation of bulk and thin-films of ZnO—The role of oxygen imperfections

Energy Technology Data Exchange (ETDEWEB)

Zatsepin, D.A. [M.N. Miheev Institute of Metal Physics of Ural Branch of Russian Academy of Sciences, 620990 Yekaterinburg (Russian Federation); Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation); Boukhvalov, D.W., E-mail: danil@hanyang.ac.kr [Department of Chemistry, Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 04763 (Korea, Republic of); Theoretical Physics and Applied Mathematics Department, Ural Federal University, Mira Street 19, 620002 Yekaterinburg (Russian Federation); Gavrilov, N.V. [Institute of Electrophysics, Russian Academy of Sciences, Ural Branch, 620990 Yekaterinburg (Russian Federation); Kurmaev, E.Z. [M.N. Miheev Institute of Metal Physics of Ural Branch of Russian Academy of Sciences, 620990 Yekaterinburg (Russian Federation); Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation); Zhidkov, I.S. [Institute of Physics and Technology, Ural Federal University, 620002 Yekaterinburg (Russian Federation)

2016-11-30

Highlights: • Both theory and experiment evidence similarity of patterns of Bi-implantation in surface and bulk ZnO. • In the bulk morphology of ZnO both experiment and theory demonstrate preferability of substitutional defects. • Experiment and theory also evidence the formation of bismuth nano-clustes from substitutional and interstitial defects without formation of secondary metallic phase. • Oxygen vacancies is crucial to formation of these nano-clusters. - Abstract: An atomic and electronic structure of the bulk and thin-film morphologies of ZnO were modified using pulsed Bi-ion implantation (1 × 10{sup 17} cm{sup −2} fluence, 70 min exposure under Bi-ion beam, E{sub Bi}{sup +} = 30 keV, pulsed ion-current density of not more than 0.8 mA/cm{sup 2} with a repetition rate of 12.5 Hz). The final samples were qualified by X-ray photoelectron core-level and valence band mapping spectroscopy applying ASTM materials science standard. The spectroscopy data obtained was discussed on the basis of DFT-models for Bi-embedding into ZnO host-matrices. It was established that in the case of direct Bi-impurities insertion into the employed ZnO-host for both studied morphologies neither the only “pure” Bi{sub 2}O{sub 3}-like phase nor the only “pure” Bi-metal will be preferable to appear as a secondary phase. An unfavorability of the large cluster agglomeration of Bi-impurities in ZnO-hosts has been shown and an oxygen 2s electronic states pleomorphizm was surely established.

Synthesis of highly conductive thin-walled Al-doped ZnO single-crystal microtubes by a solid state method

Science.gov (United States)

Hu, Shuopeng; Wang, Yue; Wang, Qiang; Xing, Cheng; Yan, Yinzhou; Jiang, Yijian

2018-06-01

ZnO has attracted considerable attention in fundamental studies and practical applications for the past decade due to its outstanding performance in gas sensing, photocatalytic degradation, light harvesting, UV-light emitting/lasing, etc. The large-sized thin-walled ZnO (TW-ZnO) microtube with stable and rich VZn-related acceptors grown by optical vapor supersaturated precipitation (OVSP) is a novel multifunctional optoelectronic material. Unfortunately, the OVSP cannot achieve doping due to the vapor growth process. To obtain doped TW-ZnO microtubes, a solid state method is introduced in this work to achieve thin-walled Al-doping ZnO (TW-ZnO:Al) microtubes with high electrical conductivity. The morphology and microstructures of ZnO:Al microtubes are similar to undoped ones. The Al3+ ions are confirmed to substitute Zn2+ sites and Zn(0/-1) vacancies in the lattice of ZnO by EDS, XRD, Raman and temperature-dependent photoluminescence analyses. The Al dopant acting as a donor level offers massive free electrons to increase the carrier concentrations. The resistivity of the ZnO:Al microtube is reduced down to ∼10-3 Ω·cm, which is one order of magnitude lower than that of the undoped microtube. The present work provides a simple way to achieve doped ZnO tubular components for potential device applications in optoelectronics.

Effect of dopants and thermal treatment on properties of Ga-Al-ZnO thin films fabricated by hetero targets sputtering system

International Nuclear Information System (INIS)

Hong, JeongSoo; Matsushita, Nobuhiro; Kim, KyungHwan

2013-01-01

In this study, we fabricated Ga and Al doped ZnO (Ga-Al-ZnO; GAZO) thin films by using the facing targets sputtering system under various conditions such as input current and thermal treatment temperature. The properties of the as-deposited GAZO thin films were examined by four-point, UV/Vis spectrometry, X-ray diffraction, atomic force microscopy and field-emission scanning electron microscopy. The result showed that the lowest sheet resistance of the films was 59.3 ohm/sq and transmittance was about 85%. After thermal treatment, the properties of GAZO thin films were improved. The lowest sheet resistance (47.3 ohm/sq) of the GAZO thin films were obtained at thermal treatment temperature of 300 °C, considered to be the result of continuous substitutions by dopants and improved crystallinity by the thermal treatment. - Highlights: ► Ga and Al doped ZnO thin films were prepared by hetero targets sputtering system. ► Free electrons were increased due to the continuous substitutions of Ga and Al. ► Crystallinity was improved by recombination of particles with increasing of temperature

Epitaxial Garnets and Hexagonal Ferrites.

Science.gov (United States)

1982-04-20

guide growth of the epitaxial YIG films. Aluminum or gallium substitu- tions for iron were used in combination with lanthanum substitutions for yttrium... gallate spinel sub- strates. There was no difficulty with nucleation in the melt and film quality appeared to be similar to that observed previously...hexagonal ferrites. We succeeded in growing the M-type lead hexaferrite (magnetoplumbite) on gallate spinel substrates. We found that the PbO-based

Two different mechanisms on UV emission enhancement in Ag-doped ZnO thin films

International Nuclear Information System (INIS)

Xu, Linhua; Zheng, Gaige; Zhao, Lilong; Pei, Shixin

2015-01-01

Ag-doped ZnO thin films were prepared by a sol–gel method. The structural, morphological and optical properties of the samples were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), UV–vis and photoluminescence spectra. The results show that the Ag in the ZnO thin films annealed at 500 °C for 1 h substitutes for Zn and exists in the form of Ag + ion (Ag Zn ) while the Ag in the ZnO thin films without a post-annealing mainly exists in the form of simple substance (Ag 0 ). The incorporation of Ag indeed can improve the ultraviolet emission of ZnO thin films and suppress the visible emissions at the same time. However, the mechanisms on the ultraviolet emission enhancement in the annealed and unannealed Ag-doped ZnO thin films are very different. As for the post-annealed Ag-doped ZnO thin films, the UV emission enhancement maybe mainly results from more electron–hole pairs (excitons) due to Ag-doping while for the unannealed Ag-doped ZnO thin films; the UV emission enhancement is attributed to the resonant coupling between exciton emission in ZnO and localized surface plasmon in Ag nanoparticles. - Highlights: • Ag-doped ZnO thin films have been prepared by the sol–gel method. • Ag-doping can enhance ultraviolet emission of ZnO thin films and depress the visible emissions at the same time. • There are two different mechanisms on UV emission enhancement in Ag-doped ZnO thin films. • The UV emission enhancement from the resonant coupling between excitonic emissions and localized surface plasmon in Ag nanoparticle is very attractive

High spin levels in 62Zn, 64Zn, 66Zn, and 68Zn

International Nuclear Information System (INIS)

Bruandet, J.-F.

1976-01-01

Investigation by in-beam gamma spectroscopy of high-spin states in the even zinc isotopes has been made using the Ni(α,2nγ)Zn reactions at Esub(α) approximately equal to 30MeV for 62 Zn, 64 Zn and 66 Zn, and the 65 Cu(α,pγ) reaction at Esub(α) approximately equal to 18MeV for 68 Zn. The high-spin states feeding by varying the incident particles: p, 3 He,α, 12 C is discussed. It is pointed out that the gsub(9/2) orbital plays an important role in the structure of the high-spin states. The variation of the inertia momentum throughout the yrast line shows a backbending behavior and a shape transition associated to the occurence, for J>6, of rotational states is speculated [fr

Stability and band offsets between c-plane ZnO semiconductor and LaAlO3 gate dielectric

Science.gov (United States)

Wang, Jianli; Chen, Xinfeng; Wu, Shuyin; Tang, Gang; Zhang, Junting; Stampfl, C.

2018-03-01

Wurtzite-perovskite heterostructures composed of a high dielectric constant oxide and a wide bandgap semiconductor envision promising applications in field-effect transistors. In the present paper, the structural and electronic properties of LaAlO3/ZnO heterojunctions are investigated by first-principles calculations. We study the initial adsorption of La, Al, and oxygen atoms on ZnO (0001) and (000 1 ¯ ) surfaces and find that La atoms may occupy interstitial sites during the growth of stoichiometric ZnO (0001). The band gap of the stoichiometric ZnO (0001) surface is smaller than that of the stoichiometric ZnO (000 1 ¯ ) surface. The surface formation energy indicates that La or Al atoms may substitute Zn atoms at the nonstoichiometric ZnO (0001) surface. The atomic charges, electronic density of states, and band offsets are analyzed for the optimized LaAlO3/ZnO heterojunctions. There is a band gap for the LaAlO3/ZnO (000 1 ¯ ) heterostructures, and the largest variation in charge occurs at the surface or interface. Our results suggest that the Al-terminated LaAlO3/ZnO (000 1 ¯ ) interfaces are suitable for the design of metal oxide semiconductor devices because the valence and conduction band offsets are both larger than 1 eV and the interface does not produce any in-gap states.

Coupling of the orthorhombic distortion to the depression of the Tc's due to Zn2+ doping in the ''RE-123'' HTSC's: A (d + s)-wave picture

International Nuclear Information System (INIS)

Tang, I.M.; Thongruang, R.; Charoenthai, N.

1999-01-01

The depressions of the T c 's of the 123 REBa 2 Cu 3 O 7 HTSC's due to the substitution of Zn 2+ ions into the Cu(2) layer are studied. The orthorhombic distortion which occurs in the 123 ceramics is assumed to induce a modification to the spin-fluctuation (SF) mediated pairing interaction which in turn causes the order parameters of these HTSC's to be of mixed (d + s)-wave symmetry. It is shown that part of the rapid depression of the T c 's caused by Zn 2+ substitution into the CuO 2 is due to a reduction of the SF-mediated pairing interaction. The differences in the rates of suppression of T c due to Zn 2+ doping in the different RE-123 HTSC's are shown to be due to the changes in the orthorhombicity which depend on the size of the rare earth ions

Coupling of the Orthorhombic Distortion to the Depression of the Tc'S due to Zn2+ Doping in the "RE-123" Htsc's:. a (d+s)-WAVE Picture

Science.gov (United States)

Tang, I. M.; Charoenthai, N.; Thongruang, R.

The depressions of the Tc's of the "123" REBa2Cu3O7 HTSC's due to the substitution of Zn2+ ions into the Cu(2) layer are studied. The orthorhombic distortion which occurs in the "123" ceramics is assumed to induce a modification to the spin-fluctuation (SF) mediated pairing interaction which inturn causes the order parameters of these HTSC's to be of mixed (d+s)-wave symmetry. It is shown that part of the rapid depression of the Tc's caused by Zn2+ substitution into the CuO2 is due to a reduction of the SF-mediated pairing interaction. The differences in the rates of suppression of Tc due to Zn2+ doping in the different "RE-123" HTSC's are shown to be due to the changes in the orthorhombicity which depend on the size of the rare earth ions.

Effect of zinc concentration on the structural and magnetic properties of mixed Co–Zn ferrites nanoparticles synthesized by sol/gel method

Energy Technology Data Exchange (ETDEWEB)

Ben Ali, M., E-mail: m.benali06@gmail.com [MAScIR Foundation, Institute of Nanomaterials and Nanotechnologies, Materials & Nanomaterials Center, B.P., 10100 Rabat (Morocco); Laboratory of Magnetism and the Physics of the high Energies, URAC 12, Department of Physics, B.P. 1014, Faculty of Science, Mohammed V University, Rabat (Morocco); El Maalam, K. [MAScIR Foundation, Institute of Nanomaterials and Nanotechnologies, Materials & Nanomaterials Center, B.P., 10100 Rabat (Morocco); Laboratory of Magnetism and the Physics of the high Energies, URAC 12, Department of Physics, B.P. 1014, Faculty of Science, Mohammed V University, Rabat (Morocco); El Moussaoui, H.; Mounkachi, O. [MAScIR Foundation, Institute of Nanomaterials and Nanotechnologies, Materials & Nanomaterials Center, B.P., 10100 Rabat (Morocco); Hamedoun, M., E-mail: m.hamedoun@mascir.com [MAScIR Foundation, Institute of Nanomaterials and Nanotechnologies, Materials & Nanomaterials Center, B.P., 10100 Rabat (Morocco); Masrour, R. [Laboratory of Materials, Processes, Environment and Quality, Cady Ayyed University, National School of Applied Sciences, PB 63 46000, Safi (Morocco); Hlil, E.K. [Institut Néel, CNRS-UJF, B.P. 166, 38042 Grenoble Cedex (France); Benyoussef, A. [MAScIR Foundation, Institute of Nanomaterials and Nanotechnologies, Materials & Nanomaterials Center, B.P., 10100 Rabat (Morocco); Laboratory of Magnetism and the Physics of the high Energies, URAC 12, Department of Physics, B.P. 1014, Faculty of Science, Mohammed V University, Rabat (Morocco)

2016-01-15

Synthesization of zinc-substituted cobalt ferrites nano-particles Co{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} (x=0.0–0.3) has been achieved by the sol/gel method. The characterization of the synthesized nano-particles has been done by X-ray diffractometry (XRD), transmission electron microscopy (TEM) and Fourier transform infrared spectroscopy (FITR). The relation between the composition and magnetic properties has been investigated by Magnetic Properties Measurement System (MPMS). The results revealed that the nanoparticles size is in the range of 11–28 nm. It was found that the zinc substitution in cobalt ferrite increases saturation magnetization from 60.92 emu/g (x=0) to 74.67 emu/g (x=0.3). Nevertheless, zinc concentrations cause a significant decrease in coercivity.▪ - Highlights: • The nanocrystals size of synthesized of Co{sub 1−x}Zn{sub x}Fe{sub 2}O{sub 4} is of 11–28 nm. • The zinc substitution in cobalt ferrite increase saturation magnetization. • The increase of zinc concentration causes a significant decrease in coercivity.

Optical and magnetic resonance investigations of Zn1-x Mn x O magnetic semiconductors

International Nuclear Information System (INIS)

Zhang Huawei; Shi Erwei; Chen Zhizhan; Liu Xuechao; Xiao Bing; Song Lixin

2006-01-01

Zn 1- x Mn x O crystallites were synthesized by hydrothermal method. X-ray diffraction, UV-Vis absorption spectroscopy, and electron paramagnetic resonance (EPR) spectra confirm the substitution of Zn site by Mn 2+ ion. The nonmonotonic variation of band gap exhibits that the short-ranged interactions between the d electrons of Mn and the s and p electrons of the host bands are dominated at lower Mn concentration (x). EPR spectra show that Mn 2+ is in exchange interaction at higher x. By using a Curie-Weiss equation on the EPR data, it is found that the dominant magnetic property is antiferromagnetic for higher x, and paramagnetic for lower x

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

Science.gov (United States)

Neogi, S. K.; Karmakar, R.; Misra, A. K.; Banerjee, A.; Das, D.; Bandyopadhyay, S.

2013-11-01

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn1-xMnxO samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol-gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV-visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO3) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ1 and τ2 are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. Single phase structure has been observed up to 6 at% of Mn doping. Impurity phase has been developed above 6 at% of Mn doping. Antiferromagnetic and paramagnetic interactions are present in the samples. Defect parameters show sharp fall as Mn concentration above 6 at%. The magnetic and defect properties are modified by the formation of impurity phase.

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

International Nuclear Information System (INIS)

Neogi, S.K.; Karmakar, R.; Misra, A.K.; Banerjee, A.; Das, D.; Bandyopadhyay, S.

2013-01-01

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn 1−x Mn x O samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol–gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV–visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO 3 ) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ 1 and τ 2 are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. - highlights: • Single phase structure has been observed up to 6 at% of Mn doping. • Impurity phase has been developed above 6 at% of Mn doping. • Antiferromagnetic and paramagnetic interactions are present in the samples. • Defect parameters show sharp fall as Mn concentration above 6 at%. • The magnetic and defect properties are modified by the formation of impurity phase

Physical properties of antiferromagnetic Mn doped ZnO samples: Role of impurity phase

Energy Technology Data Exchange (ETDEWEB)

Neogi, S.K.; Karmakar, R. [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); Misra, A.K. [UGC DAE Consortium for Scientific Research, Salt Lake, Kolkata 700064 (India); Banerjee, A. [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); CRNN, University of Calcutta, JD 2, Sector III, Salt Lake, Kolkata 700098 (India); Das, D. [UGC DAE Consortium for Scientific Research, Salt Lake, Kolkata 700064 (India); Bandyopadhyay, S., E-mail: sbaphy@caluniv.ac.in [Department of Physics, University of Calcutta, 92 A.P.C. Road, Kolkata 700009 (India); CRNN, University of Calcutta, JD 2, Sector III, Salt Lake, Kolkata 700098 (India)

2013-11-15

Structural, morphological, optical, and magnetic properties of nanocrystalline Zn{sub 1−x}Mn{sub x}O samples (x=0.01, 0.02, 0.04, 0.06, 0.08 and 0.10) prepared by the sol–gel route are studied by X-ray diffraction (XRD), Scanning electron microscopy (SEM), UV–visible absorption spectroscopy, Superconducting quantum interference device (SQUID) magnetometry and positron annihilation lifetime spectroscopy (PALS). XRD confirms formation of wurzite structure in all the Mn-substituted samples. A systematic increase in lattice constants and decrease in grain size have been observed with increase in manganese doping concentration up to 6 at% in the ZnO structure. An impurity phase (ZnMnO{sub 3}) has been detected when percentage of Mn concentration is 6 at% or higher. The optical band gap of the Mn-substituted ZnO samples decrease with increase in doping concentration of manganese whereas the width of the localized states increases. The antiferromagnetic exchange interaction is strong in the samples for 2 and 4 at% of Mn doping but it reduces when the doping level increases from 6 at% and further. Positron life time components τ{sub 1} and τ{sub 2} are found to decrease when concentration of the dopant exceeds 6 at%. The changes in magnetic properties as well as positron annihilation parameters at higher manganese concentration have been assigned as due to the formation of impurity phase. - highlights: • Single phase structure has been observed up to 6 at% of Mn doping. • Impurity phase has been developed above 6 at% of Mn doping. • Antiferromagnetic and paramagnetic interactions are present in the samples. • Defect parameters show sharp fall as Mn concentration above 6 at%. • The magnetic and defect properties are modified by the formation of impurity phase.

ZnSe/ZnSeTe Superlattice Nanotips

Directory of Open Access Journals (Sweden)

Young SJ

2010-01-01

Full Text Available Abstract The authors report the growth of ZnSe/ZnSeTe superlattice nanotips on oxidized Si(100 substrate. It was found the nanotips exhibit mixture of cubic zinc-blende and hexagonal wurtzite structures. It was also found that photoluminescence intensities observed from the ZnSe/ZnSeTe superlattice nanotips were much larger than that observed from the homogeneous ZnSeTe nanotips. Furthermore, it was found that activation energies for the ZnSe/ZnSeTe superlattice nanotips with well widths of 16, 20, and 24 nm were 76, 46, and 19 meV, respectively.

Resonant Raman scattering of ZnS, ZnO, and ZnS/ZnO core/shell quantum dots

Energy Technology Data Exchange (ETDEWEB)

Milekhin, A.G. [Institute of Semiconductor Physics, Novosibirsk (Russian Federation); Novosibirsk State University, Novosibirsk (Russian Federation); Yeryukov, N.A.; Sveshnikova, L.L.; Duda, T.A. [Institute of Semiconductor Physics, Novosibirsk (Russian Federation); Himcinschi, C. [TU Bergakademie Freiberg, Institut fuer Theoretische Physik, Freiberg (Germany); Zenkevich, E.I. [Belarussian National Technical University, Minsk (Belarus); Zahn, D.R.T. [Chemnitz University of Technology, Semiconductor Physics, Chemnitz (Germany)

2012-05-15

Resonant Raman scattering by optical phonon modes as well as their overtones was investigated in ZnS and ZnO quantum dots grown by the Langmuir-Blodgett technique. The in situ formation of ZnS/ZnO core/shell quantum dots was monitored by Raman spectroscopy during laser illumination. (orig.)

Precipitated nickel doped ZnO nanoparticles with enhanced low temperature ethanol sensing properties

Directory of Open Access Journals (Sweden)

Umadevi Godavarti

2017-12-01

Full Text Available The Zn1-xNixO nanoparticles have been synthesized by novel co-precipitation method and systematically characterized by XRD, SEM, TEM and photo luminescence. The XRD patterns confirm the hexagonal wurzite structure without secondary phases in Ni substituted ZnO samples. SEM and TEM are used for the estimation of particle shape and size. In PL study there is a peak in the range of 380–390 nm in all samples that is attributed to the oxygen vacancies. Gas sensing tests reveal that Ni doped ZnO sensor has remarkably enhanced performance compared to pure ZnO detected at an optimum temperature 100 °C. It could detect ethanol gas in a wide concentration range with very high response, fast response–recovery time, good selectivity and stable repeatability. The possible sensing mechanism is discussed. The high response of ZnO Nanoparticles was attributed to large contacting surface area for electrons, oxygen, target gas molecule, and abundant channels for gas diffusion. The superior sensing features indicate the present Ni doped ZnO as a promising nanomaterial for gas sensors. The response time and recovery time of undoped is 75 s and 60 s and 0.25 at% Ni are found to be 60 s and 45 s at 100 °C respectively.

Release of Zn from maternal tissues in pregnant rats deficient in Zn or Zn and Ca

International Nuclear Information System (INIS)

Hurley, L.S.; Masters, D.G.; Lonnerdal, B.; Keen, C.L.

1986-01-01

Earlier studies have shown that diets that increase tissue catabolism reduce the teratogenic effects of Zn deficiency. The hypothesis that Zn may be released from body tissues when the metabolic state is altered was further tested. Nonpregnant Sprague Dawley females were injected with Zn-65; after equilibration, the two major pools of Zn, bone and muscle, had different specific activities (SA), muscle being much higher. Females were mated and fed diets adequate in Zn and Ca (C) or deficient in Zn (ZnD) or deficient in both Zn and Ca (ZnCaD). Calculations using weight loss in ZnD and ZnCaD rats, Zn content of maternal bone and muscle, and total fetal Zn at term indicated that in ZnCaD rats a relatively small amount of Zn from bone early in pregnancy was sufficient to prevent abnormal organogenesis, but most fetal Zn came from breakdown of maternal muscle in the last 3 days of pregnancy. Isotope data supported this conclusion. SA of Zn in ZnD fetuses was equal and high, indicating that most Zn came from the same maternal tissue. High muscle SA prior to mating, and increased SA in tibia and liver during pregnancy suggest that muscle provided Zn for other maternal tissues as well as fetuses. In contrast, SA in C fetuses was less than 30% of that of the D groups, consistent with the earlier hypothesis that most fetal Zn in C rats is accrued directly from the diet

Photoluminescence quenching and enhanced spin relaxation in Fe doped ZnO nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Ovhal, Manoj M.; Santhosh Kumar, A. [Department of Materials Engineering, Defence Institute of Advanced Technology, Girinagar, Pune 411025 (India); Khullar, Prerna [School of Materials Science and Technology, Indian Institute of Technology (Banaras Hindu University), Varanasi 221005 (India); Kumar, Manjeet [Department of Materials Engineering, Defence Institute of Advanced Technology, Girinagar, Pune 411025 (India); Abhyankar, A.C., E-mail: ashutoshabhyankar@gmail.com [Department of Materials Engineering, Defence Institute of Advanced Technology, Girinagar, Pune 411025 (India)

2017-07-01

Cost-effective ultrasonically assisted precipitation method is utilized to synthesize Zinc oxide (ZnO) nanoparticles (NPs) at room temperature and the effect of Iron (Fe) doping on structural, optical and spin relaxation properties also presented. As-synthesized pure and Fe doped ZnO NPs possess a perfect hexagonal growth habit of wurtzite zinc oxide, along the (101) direction of preference. With Fe doping, ‘c/a’ ratio and compressive lattice strain in ZnO NPs are found to reduce and increase, respectively. Raman studies demonstrate that the E{sub 1} longitudinal optical (LO) vibrational mode is very weak in pure which remarkably enhanced with Fe doping into ZnO NPs. The direct band gap energy (E{sub g}) of the ZnO NPs has been increased from 3.02 eV to 3.11 eV with Fe doping. A slight red-shift observed with strong green emission band, in photoluminescence spectra, is strongly quenched in 6 wt.% Fe doped ZnO NPs. The field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM) reveals spherical shape of ZnO NPs with 60–70 nm, which reduces substantially on Fe doping. The energy dispersive X-ray spectrum and elemental mapping confirms the homogeneous distribution of Fe in ZnO NPs. Moreover, the specific relaxation rate (R{sub 2sp} = 1/T{sub 2}) has been measured using Carr-Purcell-Meiboom-Gill (CPMG) method and found to be maximum in 6 wt.% Fe doped ZnO NPs. Further, the correlation of structural, optical and dynamic properties is proposed. - Highlights: • Pure ZnO and Fe doped ZnO NPs were successfully prepared by cost effective ultrasonically assisted precipitation method. • The optical band gap of ZnO has been enhanced form 3.02–3.11 eV with Fe doping. • PL quenching behaviour has been observed with Fe{sup 3+} ions substitution in ZnO lattice. • Specific relaxation rate (R{sub 2sp} = 1/T{sub 2}) has been varied with Fe doping and found to be maximum in 6 wt.% Fe doped ZnO NPs.

The single crystal structure determination of Ln{sub 6}MnSb{sub 15} (Ln=La, Ce), Ln{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), and Ln{sub 6}ZnSb{sub 15} (Ln=La-Pr)

Energy Technology Data Exchange (ETDEWEB)

Benavides, Katherine A.; McCandless, Gregory T.; Chan, Julia Y. [Texas Univ., Dallas, Richardson, TX (United States). Dept. of Chemistry and Biochemistry

2017-09-01

Single crystals of Ln{sub 6}MnSb{sub 15} (Ln=La, Ce), Ln{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), and Ln{sub 6}ZnSb{sub 15} (Ln=La-Pr) have been successfully grown and the compounds adopt the orthorhombic Ln{sub 6}MnSb{sub 15} structure type (space group Immm), with a∝4.3 Aa, b∝15 Aa, and c∝19 Aa. This structure is comprised of antimony nets and antimony ribbons which exhibit positional disorder at connecting points between antimony substructures, in addition to two partially occupied transition metal sites. The unit cell volumes of the La analogs displayed a systematic decrease upon Zn substitution. However, for the Ce{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} and Pr{sub 6}Mn{sub 1-x}Zn{sub x}Sb{sub 15} (x∝0.5), the volumes deviate from linearity as observed in the parent compounds.

Equilibrium and NMR studies on GdIII, YIII, CuII and ZnII complexes of various DTPA-N,N''-bis(amide) ligands. Kinetic stabilities of the gadolinium(III) complexes.

Science.gov (United States)

Jászberényi, Zoltán; Bányai, István; Brücher, Ernö; Király, Róbert; Hideg, Kálmán; Kálai, Tamás

2006-02-28

Three DTPA-derivative ligands, the non-substituted DTPA-bis(amide) (L(0)), the mono-substituted DTPA-bis(n-butylamide) (L(1)) and the di-substituted DTPA-bis[bis(n-butylamide)] (L(2)) were synthesized. The stability constants of their Gd3+ complexes (GdL) have been determined by pH-potentiometry with the use of EDTA or DTPA as competing ligands. The endogenous Cu2+ and Zn2+ ions form ML, MHL and M(2)L species. For the complexes CuL(0) and CuL(1) the dissociation of the amide hydrogens (CuLH(-1)) has also been detected. The stability constants of complexes formed with Gd3+, Cu2+ and Zn2+ increase with an increase in the number of butyl substituents in the order ML(0) DTPA)2-, while the complex GdL2 possesses a much higher kinetic stability.

A low temperature situ precipitation route to designing Zn-doped SnO2 photocatalyst with enhanced photocatalytic performance

International Nuclear Information System (INIS)

Jia, Xiaohua; Liu, Yingying; Wu, Xiangyang; Zhang, Zhen

2014-01-01

Highlights: • A new Zn doped SnO 2 photocatalyst was successfully achieved and characterized. • The Zn doped SnO 2 photocatalyst exhibited excellent photocatalytic activity and stability for the photodegradation RhB. • Photocatalytic mechanisms both under visible and UV–vis light irradiation were proposed. - Abstract: Zn doped SnO 2 nanoparticles have been fabricated through the low temperature situ precipitation technique. The morphology, structure and chemical composition of the nanoparticles are characterized using field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy (DRS), Thermogravimetric-differential scanning calorimetry (TG–DSC) and UV–vis absorption spectroscopy. The products were also characterized by X-ray diffraction (XRD) and X-photoelectron spectrum (XPS), and the results indicated that Sn 4+ ions were successfully substituted by Zn 2+ . Their photocatalytic activities were evaluated using rhodamine B (RhB) as a decomposition objective. The results show that the Zn doped SnO 2 display higher photocatalytic activities in the degradation of RhB than pure ZnO products by exposure to UV irradiation. A possible reason of the increased photocatalytic activity of Zn doped SnO 2 is attributed to intrinsic oxygen vacancies in nanoparticles and extrinsic defect due to Zn hole doping

Atomic absorption photometry of excess Zn in ZnO

Energy Technology Data Exchange (ETDEWEB)

Lott, K.; Shinkarenko, S.; Tuern, L. [Department of Materials Science, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn (Estonia); Kirsanova, T.; Grebennik, A.; Vishnjakov, A. [Department of Physical Chemistry, D. Mendelejev University of Chemical Technology of Russia, Miusskaya Sq. 9, 125047 Moscow (Russian Federation)

2005-02-01

Zn excess in ZnO is built up automatically at high temperatures. Excess Zn in hydrothermally grown ZnO single crystals were investigated by the atomic absorption photometry (AAP) method. To determine the excess zinc in ZnO samples, the AAP of zinc vapour was used in the conditions of solid-vapour equilibrium. Zn AAP allowed to eliminate excess Zn connected differentially in ZnO samples. To fix Zn non-stoichiometry, all the ZnO samples tested were previously heat treated at temperature interval from 850 to 900 C and at fixed Zn vapour pressures from 0.1 to 0.9 of saturated zinc vapour pressure at given treatment temperature. The analysis of temperature dependence of zinc vapour pressure indicated that the impurity metals take active role in the determination of non-stoichiometric zinc. The impurities Mn, Fe, Co, Ni and Cu form oxides which will reduce during annealing in Zn vapor up to metals form. During AAP measurement in optical cuvette, these metals react with ZnO and give additional Zn vapor pressure. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Ultrafast intramolecular relaxation dynamics of Mg- and Zn-bacteriochlorophyll a

Energy Technology Data Exchange (ETDEWEB)

Kosumi, Daisuke [Osaka City University Advanced Research Institute for Natural Science and Technology, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan); CREST/JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Nakagawa, Katsunori; Sakai, Shunsuke [Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555 (Japan); Nagaoka, Yuya; Maruta, Satoshi; Sugisaki, Mitsuru [CREST/JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Department of Physics, Graduate School of Science, Osaka City University, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan); Dewa, Takehisa [Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555 (Japan); PRESTO/JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Nango, Mamoru [The Osaka City University Advanced Research Institute for Natural Science and Technology, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan); CREST/JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya 466-8555 (Japan); Hashimoto, Hideki [The Osaka City University Advanced Research Institute for Natural Science and Technology, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan); CREST/JST, 4-1-8 Honcho, Kawaguchi, Saitama 332-0012 (Japan); Department of Physics, Graduate School of Science, Osaka City University, 3-3-138 Sugimoto, Sumiyoshi-ku, Osaka 558-8585 (Japan)

2013-07-21

Ultrafast excited-state dynamics of the photosynthetic pigment (Mg-)bacteriochlorophyll a and its Zn-substituted form were investigated by steady-state absorption/fluorescence and femtosecond pump-probe spectroscopic measurements. The obtained steady-state absorption and fluorescence spectra of bacteriochlorophyll a in solution showed that the central metal compound significantly affects the energy of the Q{sub x} state, but has almost no effect on the Q{sub y} state. Photo-induced absorption spectra were recorded upon excitation of Mg- and Zn-bacteriochlorophyll a into either their Q{sub x} or Q{sub y} state. By comparing the kinetic traces of transient absorption, ground-state beaching, and stimulated emission after excitation to the Q{sub x} or Q{sub y} state, we showed that the Q{sub x} state was substantially incorporated in the ultrafast excited-state dynamics of bacteriochlorophyll a. Based on these observations, the lifetime of the Q{sub x} state was determined to be 50 and 70 fs for Mg- and Zn-bacteriochlorophyll a, respectively, indicating that the lifetime was influenced by the central metal atom due to the change of the energy gap between the Q{sub x} and Q{sub y} states.

Rare earths in GaN and ZnO studied with the PAC method; Seltene Erden in GaN und ZnO untersucht mit der PAC-Methode

Energy Technology Data Exchange (ETDEWEB)

Nedelec, R.

2007-07-01

The present thesis deals with the implantation and annealing behaviour of two examples of large-band-gap semiconductors GaN and ZnO. The studies begin with the annealing behaviour of GaN after the implantation of {sup 172}Lu. For GaN the annealing process begins at low temperatures with the decreasing of the damping of the lattice frequency. At essentially higher temperatures finally the substitunial contribution increases. This behaviour is also observed for other probe nuclei in GaN. For ZnO the behaviour at low temperature is different. Both for {sup 172}Lu and for {sup 181}Hf the damping is already after the implantation very low. The increasement of the substitutional contribution occurs like in GaN at higher temperatures. Thereafter for GaN and ZnO PAC spectra were token up at different measurement temperatures between 25 and 873 K. For {sup 172}Lu in GaN and in ZnO a strong temperature dependence of the lattice field gradient was observed. Also for {sup 181}Hf in ZnO a strong temperature dependence is observed. For {sup 172}Lu by means of a model for the interaction of quadrupole moments of electronic shells with the nucleus a lattice field gradient of {+-}5.9.10{sup 15} Vcm{sup -2} could be determined. For {sup 172}Lu in ZnO the model yields at 293 K a lattice field gradient of +14.10{sup 15} Vcm{sup -2} respectively -13.10{sup 15} Vcm{sup -2}. The corrsponding measurement with {sup 181}Hf yields a lattice field gradient of {+-}5.7.10{sup 15} Vcm{sup -2}.

Inter-atomic bonding and dielectric polarization in Gd"3"+ incorporated Co-Zn ferrite nanoparticles

International Nuclear Information System (INIS)

Pawar, R.A.; Desai, S.S.; Patange, S.M.; Jadhav, S.S.; Jadhav, K.M.

2017-01-01

A series of ferrite with a chemical composition Co_0_._7Zn_0_._3Gd_xFe_2_−_xO_4 (where x=0.0 to x=0.1) were prepared by sol-gel auto-combustion method. X-ray diffraction pattern were used to determine the crystal structure and phase formation of the prepared samples. Scanning electron microscopy is used to study the surface morphology of the prepared samples. Elastic properties were determined from the infrared spectroscopy. Debye temperature, wave velocities, elastic constants found to increase with the increase in Gd"3"+ substitution. Dielectric properties such as dielectric constant and dielectric loss were studied as a function of Gd"3"+ substitution and frequency. Dielectric constant decreased with the increase in frequency and Gd"3"+ substitution. Behavior of dielectric properties was explained on the basis of Maxwell-Wagner interfacial polarization which in accordance with Koops phenomenological theory. Real and imaginary part of impedance was studied as a function of resistance and Gd"3"+ substitution. The behavior of impedance is systematically discussed on the basis of resistance-capacitance circuit.

The origin of room temperature ferromagnetism mediated by Co–VZn complexes in the ZnO grain boundary

KAUST Repository

Devi, Assa Aravindh Sasikala

2016-05-20

Ferromagnetism in polycrystalline ZnO doped with Co has been observed to be sustainable in recent experiments. We use first-principle calculations to show that Co impurities favorably substitute at the grain boundary (GB) rather than in the bulk. We reveal that room-temperature ferromagnetism (RTFM) at the Co-doped ZnO GB in the presence of Zn vacancies is due to ferromagnetic exchange coupling of a pair of closely associated Co atoms in the GB, with a ferromagnetic exchange coupling energy of ∼300 meV, which is in contrast to a previous study that suggested the O vacancy-Co complex induced ferromagnetism. Electronic structure analysis was used to predict the exchange coupling mechanism, showing that the hybridization of O p states with Co and Zn d states enhances the magnetic polarization originating from the GB. Our results indicate that RTFM originates from Co clusters at interfaces or in GBs. © 2016 The Royal Society of Chemistry.

Studies on solid solutions based on layered honeycomb-ordered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn)

Energy Technology Data Exchange (ETDEWEB)

Berthelot, Romain; Schmidt, Whitney; Sleight, A.W. [Department of Chemistry, Oregon State University, Corvallis, OR 97331 (United States); Subramanian, M.A., E-mail: mas.subramanian@oregonstate.edu [Department of Chemistry, Oregon State University, Corvallis, OR 97331 (United States)

2012-12-15

Three complete solid solutions between the layered phases P2-Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) have been prepared by conventional solid state method and investigated through X-ray diffraction, magnetism and optical measurements. All compositions are characterized by a M{sup 2+}/X{sup 6+} honeycomb ordering within the slabs and crystallize in a hexagonal unit cell. However, a structural transition based on a different stacking is observed as nickel (space group P6{sub 3}/mcm) is substituted by zinc or cobalt (space group P6{sub 3}22). All compositions exhibit a paramagnetic Curie-Weiss behavior at high temperatures; and the magnetic moment values confirm the presence of Ni{sup 2+} and/or Co{sup 2+} cations. The low-temperature antiferromagnetic order of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. The color of the obtained compositions varies from pink, to light green and white when M=Co, Ni, Zn, respectively. - Graphical abstract: The comparison between the structure of Na{sub 2}Ni{sub 2}TeO{sub 6} (left) and Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Zn) (right) evidences the stacking difference with distinct atom sequences along the hexagonal c-axis. Highlights: Black-Right-Pointing-Pointer Solid solutions between lamellar phases Na{sub 2}M{sub 2}TeO{sub 6} (M=Co, Ni, Zn) are investigated. Black-Right-Pointing-Pointer A M{sup 2+}/X{sup 6+} honeycomb ordering characterized all the compositions. Black-Right-Pointing-Pointer A structural transition is shown when Ni is replaced by Co or Zn. Black-Right-Pointing-Pointer The low-temperature AFM ordering of Na{sub 2}Ni{sub 2}TeO{sub 6} and Na{sub 2}Co{sub 2}TeO{sub 6} is suppressed by zinc substitution. Black-Right-Pointing-Pointer Color changes from pink to light green and white when M=Co, Ni, Zn, respectively.

Extended X-ray absorption fine structure studies of impulsive-type hardening in the heavily Be-doped ZnSe ternaries

Energy Technology Data Exchange (ETDEWEB)

Khan, Shabina; Singh, Pankaja [Barkatullah University, Bhopal (India); Mazher, Javed [Addis Ababa University, Addis Ababa (Ethiopia)

2014-02-15

Inherently soft zinc-selenides have been hardened through beryllium doping. High-quality stoichiometric ternaries of Be{sub x}Zn{sub 1-x}Se have been synthesized by using the Bridgeman technique. State-of-art X-ray absorption spectroscopy is performed by varying the concentration of the cationic dopant, Be, from 6% to 55% in the host ZnSe. Extended X-ray absorption fine structure analyses are carried out to study the next-neighbor and next nearest neighbor atomic positions, nature of the substitutional doping, extent of bond length homogeneity, the presence of involuntary contrast among path distances, and the crossover from a soft to a hard character of the ternary with increasing Be concentration. Our results indicate the presence of a non-regular impulsive hardening in the ternary with a disparity at the lower and the higher Be-doping levels, which are discussed vis-a-vis self-accommodation of substitutional dopants in the host lattice.

Effect of chromium substitution on the dielectric properties of mixed Ni-Zn ferrite prepared by WOWS sol–gel technique

International Nuclear Information System (INIS)

Ashtar, M.; Munir, A.; Anis-ur-Rehman, M.; Maqsood, A.

2016-01-01

Graphical abstract: Variation of AC conductivity (σ AC ) as a function of natural log of angular frequency (lnω) for Ni 0.5 Zn 0.5 Fe 2-x Cr x O 4 nanoferrites at room temperature. - Highlights: • Cr doped mixed Ni-Zn ferrites were successfully synthesized by a newly developed WOWS sol gel technique. • The specific surface area and specific surface area to volume ratio increased with decrease in particle size. • The resonance peaks appeared in dielectric loss graphs, shifting towards low frequency with the increase in Cr concentration. • The prepared samples have the lowest values of the dielectric constant. • The dielectric constant were observed to be inversely proportional to square root of the AC resistivity. - Abstract: Cr +3 doped Ni-Zn nanoferrite samples with composition Ni 0.5 Zn 0.5 Fe 2-x Cr x O 4 (x = 0.1, 0.2, 0.3, 0.4) were synthesized With Out Water and Surfactant (WOWS) sol-gel technique. The structural, morphological and dielectric properties of the samples were investigated. The lattice constant, crystallite size, theoretical density and porosity of each sample were obtained from X-ray diffraction (XRD) data. The specific surface area and specific surface area to volume ratio increased with the decrease in the size of Cr +3 doped Ni-Zn ferrite nanoparticles, as the concentration of Cr +3 increased. The SEM analysis revealed that the particles were of nano size and of spherical shape. The dielectric parameters such as dielectric constant (ε′) and dielectric loss (tanδ) of all the samples as a function of frequency at room temperature were measured. The AC conductivity (σ AC ) was determined from the dielectric parameters, which showed increasing trend with the rise in frequency.

Synthesis, Magnetization, and Electrical Transport Properties of Mn3Zn0.9Cu0.1N

Directory of Open Access Journals (Sweden)

Y. Yin

2013-01-01

Full Text Available We synthesized Mn3Zn0.9Cu0.1N by solid state reaction, and magnetic as well as electrical transport properties were investigated. It is found that Mn3Zn0.9Cu0.1N exhibits a first-order antiferromagnetism (AFM to paramagnetic (PM transition with the Néel temperature TN ~163 K, and substitution of Cu for Zn would favor ferromagnetism (FM state and weaken AFM ground state, leading to a convex curvature character of M(T curve. With high external fields 10 kOe–50 kOe, magnetic transition remains a robust AFM-PM feature while FM phase is completely suppressed. Thermal hysteresis of M(T under 500 Oe is also suppressed when the magnetic field exceeds 10 kOe. Mn3Zn0.9Cu0.1N exhibits a good metallic behavior except for a slope change around TN, which is closely related to AFM-PM magnetic transition. Compared with the first differential of resistivity with respect to temperature for (dρ/dTMn3ZnN in transition temperature range, the absolute value of (dρ/dTMn3Zn0.9Cu0.1N is much lower which is close to zero.

ZnMgO-ZnO quantum wells embedded in ZnO nanopillars: Towards realisation of nano-LEDs

Energy Technology Data Exchange (ETDEWEB)

Bakin, A.; El-Shaer, A.; Mofor, A.C.; Al-Suleiman, M.; Schlenker, E.; Waag, A. [Institute of Semiconductor Technology, Braunschweig Technical University, Hans-Sommer-Str. 66, 38106 Braunschweig (Germany)

2007-07-01

ZnO thin films, ZnMgO/ZnO heterostructures and ZnO nanostructures were fabricated using molecular beam epitaxy (MBE), vapour phase transport (VPT) and an aqueous chemical growth approach (ACG). The possibility to employ several fabrication techniques is of special importance for the realization of unique device structures. MBE was implemented for ZnO-based layer and heterostructure growth. Pronounced RHEED oscillations were used for growth control and optimisation, resulting in high quality ZnO and Zn{sub 1-x}Mg{sub x}O epilayers and heterostructures, as well as ZnMgO/ZnO quantum wells on sapphire and SiC substrates. A novel advanced VPT approach is developed and sapphire, SiC, ZnO epitaxial layers, and even plastic and glass were implemented as substrates for ZnO growth. The VPT fabrication of ZnO nanopillars, leading to well aligned, c-axis oriented nanopillars with excellent quality and purity is demonstrated. Successful steps were made towards device fabrication on ZnO basis. The nanopillar fabrication technique is combined with MBE technology: MBE-grown ZnMgO/ZnO quantum well structures were grown on ZnO nanopillars presenting significant progress towards nano-LEDs realization. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Microstructure and magnetic properties of M-type strontium hexagonal ferrites with Y-Co substitution

Energy Technology Data Exchange (ETDEWEB)

Liu, Chaocheng [School of Physics and Materials Science, Anhui University, Hefei 230601 (China); Liu, Xiansong, E-mail: xiansongliu@ahu.edu.cn [School of Physics and Materials Science, Anhui University, Hefei 230601 (China); Engineering Technology Research Center of Magnetic Materials, School of Physics & Materials Science, Anhui University, Hefei 230601 (China); Feng, Shuangjiu; Rehman, Khalid Mehmood Ur; Li, Mingling; Zhang, Cong; Li, Haohao; Meng, Xiangyu [School of Physics and Materials Science, Anhui University, Hefei 230601 (China)

2017-08-15

Highlights: • Y-Co substitution in strontium hexaferrites have been prepared and investigated systematically for the first time. • Lattice constants a and c for all the samples are very different with that of unsubstituted ferrites. • The M{sub s} and H{sub c} are very high, from which may provide an important significance of research and development of high performance products. - Abstract: According to the formula Sr{sub 0.95}Y{sub 0.05}Fe{sub 12−x}Co{sub x}O{sub 19} (x = 0.00, 0.08, 0.16, 0.24, 0.32, 0.40), the replacement of Y-Co in M-type strontium hexagonal ferrites have been successfully prepared by ceramic process for the first time. The phase compositions of magnetic powders were examined by X-ray diffraction. The results of XRD showed that the single phase was obtained in magnetic powders with the increase of Co content (x), and α-Fe{sub 2}O{sub 3} occurred when x > 0.24. The morphology of the magnets was investigated by scanning electron microscopy (SEM). The micro-morphology of the particles exhibited the uniform plane hexagonal structures of M-type ferrites with different Co content. Magnetic properties of the ferrite magnets were measured by a physical property measurement system-vibrating sample magnetometer (PPMS-VSM). The M{sub s} increases constantly with the increase of Co content. The H{sub c} first increases and then decreases with the increase of Co content, and the value of coercivity (H{sub c}) is up to 3774 Oe when x = 0.24.

Zinc substitution effects on the superconducting properties of Nd1.85Ce0.15CuO4-δ

International Nuclear Information System (INIS)

Garcia-Vazquez, V.; Mazumdar, S.; Falco, C.M.; Barlingay, C.; Risbud, S.H.

1990-01-01

With the discovery of the electron superconductors, a new dimension was added to research in the field of high-temperature superconductivity. Studies of these materials should help elucidate the mechanism responsible for high-temperature superconductivity, as well as improve strategies for finding new superconductors. In this paper, we discuss the superconducting structural properties of Nd 1.85 Ce 0.15 (Cu 1-y Zn y )O 4 as a function of the Zn concentration y. Detailed comparisons with previous results of similar substitution studies in the single-CuO 2 -layer hole superconductor La 1.85 Sr 0.15 CuO 4 also are made. We have found that the non-magnetic element Zn has a detrimental effect on the T'-phase electron superconductor, and that this effect is as strong as in the T-phase hole superconductor. Theoretical implications and the question of electron-hole symmetry are also discussed

Electrodeposition of Zn and Cu–Zn alloy from ZnO/CuO precursors in deep eutectic solvent

Energy Technology Data Exchange (ETDEWEB)

Xie, Xueliang [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Zou, Xingli, E-mail: xinglizou@shu.edu.cn [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Lu, Xionggang, E-mail: luxg@shu.edu.cn [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Lu, Changyuan; Cheng, Hongwei; Xu, Qian [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Zhou, Zhongfu [State Key Laboratory of Advanced Special Steel & Shanghai Key Laboratory of Advanced Ferrometallurgy & School of Materials Science and Engineering, Shanghai University, Shanghai 200072 (China); Institute of Mathematics and Physics, Aberystwyth University, Aberystwyth SY23 3BZ (United Kingdom)

2016-11-01

Graphical abstract: Micro/nanostructured Zn and Cu–Zn alloy films have been electrodeposited directly from ZnO/CuO precursors in ChCl/urea-based DES, the typical nucleation-growth mechanism and the micro/nanostructures-formation process are determined. Display Omitted - Highlights: • Micro/nanostructured Zn films have been electrodeposited directly from ZnO precursor in deep eutectic solvent (DES). • The morphology of the Zn electrodeposits depends on the cathodic potential and temperature. • The electrodeposited Zn films exhibit homogeneous morphologies with controllable particle sizes and improved corrosion resistance. • Cu–Zn alloy films have also been electrodeposited directly from their metal oxides precursors in DES. - Abstract: The electrodeposition of Zn and Cu–Zn alloy has been investigated in choline chloride (ChCl)/urea (1:2 molar ratio) based deep eutectic solvent (DES). Cyclic voltammetry study demonstrates that the reduction of Zn(II) to Zn is a diffusion-controlled quasi-reversible, one-step, two electrons transfer process. Chronoamperometric investigation indicates that the electrodeposition of Zn on a Cu electrode typically involves three-dimensional instantaneous nucleation with diffusion-controlled growth process. Micro/nanostructured Zn films can be obtained by controlling the electrodeposition potential and temperature. The electrodeposited Zn crystals preferentially orient parallel to the (101) plane. The Zn films electrodeposited under more positive potentials and low temperatures exhibit improved corrosion resistance in 3 wt% NaCl solution. In addition, Cu–Zn alloy films have also been electrodeposited directly from CuO–ZnO precursors in ChCl/urea-based DES. The XRD analysis indicates that the phase composition of the electrodeposited Cu–Zn alloy depends on the electrodeposition potential.

Anomalous diffusion of Ga and As from semi-insulating GaAs substrate into MOCVD grown ZnO films as a function of annealing temperature and its effect on charge compensation

Directory of Open Access Journals (Sweden)

Pranab Biswas

2014-05-01

Full Text Available The diffusion behavior of arsenic (As and gallium (Ga atoms from semi-insulating GaAs (SI-GaAs into ZnO films upon post-growth annealing vis-à-vis the resulting charge compensation was investigated with the help of x-ray photoelectron spectroscopy (XPS and secondary ion mass spectroscopy. The films, annealed at 600 ºC and 700 ºC showed p-type conductivity with a hole concentration of 1.1 × 1018 cm−3 and 2.8 × 1019 cm−3 respectively, whereas those annealed at 800 ºC showed n-type conductivity with a carrier concentration of 6.5 × 1016 cm−3. It is observed that at lower temperatures, large fraction of As atoms diffused from the SI-GaAs substrates into ZnO and formed acceptor related complex, (AsZn–2VZn, by substituting Zn atoms (AsZn and thereby creating two zinc vacancies (VZn. Thus as-grown ZnO which was supposed to be n-type due to nonstoichiometric nature showed p-type behavior. On further increasing the annealing temperature to 800 ºC, Ga atoms diffused more than As atoms and substitute Zn atoms thereby forming shallow donor complex, GaZn. Electrons from donor levels then compensate the p-type carriers and the material reverts back to n-type. Thus the conversion of carrier type took place due to charge compensation between the donors and acceptors in ZnO and this compensation is the possible origin of anomalous conduction in wide band gap materials.

Luminescent, magnetic and optical properties of ZnO-ZnS nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Raleaooa, Pule V. [Department of Physics, University of the Free State, ZA 9300 Bloemfontein (South Africa); Department of Chemistry, University of the Free State, ZA 9300 (South Africa); Roodt, Andreas [Department of Chemistry, University of the Free State, ZA 9300 (South Africa); Mhlongo, Gugu G.; Motaung, David E. [DST/CSIR Nanotechnology Innovation Center, National Center for Nano-Structured Materials, Council for Scientific and Industrial Research, P.O. Box 395, ZA 0001 Pretoria (South Africa); Kroon, Robin E. [Department of Physics, University of the Free State, ZA 9300 Bloemfontein (South Africa); Ntwaeaborwa, Odireleng M., E-mail: ntwaeab@gmail.com [School of Physics, University of the Witwatersrand, Private Bag 3, Wits, ZA 2050 (South Africa)

2017-02-15

The structure, particle morphology, optical and magnetic properties of ZnO, ZnS and ZnO-ZnS nanoparticles prepared by the sol-gel method are reported. ZnO and ZnS were combined at room temperature by an ex situ synthetic route to prepare ZnO-ZnS nanocomposites. The nanocomposites exhibited particle morphology different from that of ZnO and ZnS nanoparticles. The ZnO and ZnS nanoparticles exhibited quantum confinement as inferred from the widening of their respective bandgap energies. The electron paramagnetic resonance data provided evidence for the existence of magnetic clusters near the surface, electron to nuclei interactions and defect states. The ZnO-ZnS nanocomposites exhibited tunable emission that was dependent on the ratio of ZnO to ZnS. These composites were evaluated for application in different types of light emitting devices.

Mg doping induced high structural quality of sol–gel ZnO nanocrystals: Application in photocatalysis

Energy Technology Data Exchange (ETDEWEB)

Abed, Chayma; Bouzidi, Chaker [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, BP 95, Hammam-Lif 2050 (Tunisia); Elhouichet, Habib, E-mail: Habib.elhouichet@fst.rnu.tn [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, BP 95, Hammam-Lif 2050 (Tunisia); Département de Physique, Faculté des Sciences de Tunis, Université Tunis El Manar, Tunis 2092 (Tunisia); Gelloz, Bernard [Graduate School of Engineering, Nagoya University, 2-24-16 Furo-cho, Chikusa-ku, Nagoya, Aichi 464-8603 (Japan); Ferid, Mokhtar [Laboratoire de Physico-chimie des Matériaux Minéraux et leurs Applications, Centre National de Recherches en Sciences des Matériaux, BP 95, Hammam-Lif 2050 (Tunisia)

2015-09-15

Highlights: • ZnO nancrystals doped with Mg were prepared from sol–gel method. • Structural and optical properties of ZnO:Mg nanocrystals were investigated. • Good crystalline quality of ZnO nanocrystals was reported after Mg doping. • Good photocatalytic activity of Mg doped ZnO nanocrystals was demonstrated under sun light illumination. - Abstract: Undoped and Mg doped ZnO nanocrystals (NCs) ZnO:x%Mg (x = 1, 2, 3, and 5) were synthesized using sol–gel method. The structural and optical properties were investigated by X-ray diffraction (XRD), Raman spectroscopy, diffuse reflectivity, and photoluminescence (PL). XRD analysis demonstrates that all prepared samples present pure hexagonal wurtzite structure without any Mg related phases. The NCs size varies from 26.82 nm to 42.96 nm with Mg concentrations; it presents an optimal value for 2% of Mg. The Raman spectra are dominated by the E{sub 2high} mode. For highly Mg doping (5%), the occurrence of silent B{sub 1(low)} mode suggested that the Mg ions do substitute at Zn sites in the ZnO lattice The band gap energy was estimated from both Tauc and Urbach methods and found to be 3.39 eV for ZnO:2%Mg. The PL spectra exhibit two emission bands in the UV and visible range. Their evolution with Mg doping reveals the reduction of defect density in ZnO at low Mg doping by filling Zn vacancies. In addition, it was found that further Mg doping, above 2%, improves the photocatalytic activity of ZnO NCs for photodegradation of Rhodamine B (RhB) under sunlight irradiation. The efficient electron–hole separation is the main factor responsible for the enhancement of photocatalytic performance of Mg doped ZnO NCs. Through this work, we show that by varying the Mg contents in ZnO, this material can be a potential candidate for both optoelectronic and photocatalytic applications.

Photodegradation of malachite green dye catalyzed by Keggin-type polyoxometalates under visible-light irradiation: Transition metal substituted effects

Science.gov (United States)

Liu, Chun-Guang; Zheng, Ting; Liu, Shuang; Zhang, Han-Yu

2016-04-01

In the present paper, Keggin-type polyoxometalates (POMs) (NH4)3[PW12O40] and its mono-transition-metal-substituted species (NH4)5[{PW11O39}MII(H2O)] (M = Mn, Fe, Co, Ni, Cu, Zn) have been synthesized and used as photocatalyst to activate O2 for the degradation of dye molecule under visible-light irradiation. Because of the strong adsorption on the surface of POM catalyst, malachite green (MG) molecule was employed as a molecular probe to test their photocatalytic activity. The photodegradation study shows that introduction of transition metal ion leads to an increase in the degradation of MG in the following order: Mn < Fe < Co < [PW12O40]3- < Ni < Cu < Zn, which indicates that the photocatalytic activity of these POMs is sensitive to the transition metal substituted effects. Electronic structure analysis based on the density functional theory calculations shows that a moderate decrease of oxidizing ability of POM catalyst may improve the photocatalytic activity in the degradation of dye molecule under visible-light irradiation. Meanwhile, intermediate products about the photocatalytic oxidation of MG molecule were proposed on the basis of gas chromatograph mass spectrometer analysis.

Alloy formation and chemisorption at Zn/Pt(111) bimetallic surfaces using alkali ISS, XPD, and TPD.

Science.gov (United States)

Ho, Chih-Sung; Martono, Eddie; Banerjee, Santanu; Roszell, John; Vohs, John; Koel, Bruce E

2013-11-21

Alloy formation and chemisorption at bimetallic surfaces formed by vapor-depositing Zn on a Pt(111) single crystal were investigated primarily by using X-ray photoelectron diffraction (XPD), X-ray photoelectron spectroscopy (XPS), low-energy alkali ion scattering spectroscopy (ALISS), low electron energy diffraction (LEED), and temperature programmed desorption (TPD). A wide range of conditions were investigated to explore whether deposition and annealing of Zn films could produce well-defined, ordered alloy surfaces, similar to those encountered for Sn/Pt(111) surface alloys. These attempts were unsuccessful, although weak, diffuse (2 × 2) spots were observed under special conditions. The particular PtZn bimetallic alloy created by annealing one monolayer of Zn on Pt(111) at 600 K, which has a Zn composition in the surface layer of about 5 at. %, was investigated in detail by using XPD and ALISS. Only a diffuse (1 × 1) pattern was observed from this surface by LEED, suggesting that no long-range, ordered alloy structure was formed. Zn atoms were substitutionally incorporated into the Pt(111) crystal to form a near-surface alloy in which Zn atoms were found to reside primarily in the topmost and second layers. The alloyed Zn atoms in the topmost layer are coplanar with the Pt atoms in the surface layer, without any "buckling" of Zn, that is, displacement in the vertical direction. This result is expected because of the similar size of Pt and Zn, based on previous studies of bimetallic Pt alloys. Zn atoms desorb upon heating rather than diffusing deep into the bulk of the Pt crystal. Temperature programmed desorption (TPD) measurements show that both CO and NO have lower desorption energies on the PtZn alloy surface compared to that on the clean Pt(111) surface.

Optical and Magnetic Properties of Fe Doped ZnO Nanoparticles Obtained by Hydrothermal Synthesis

Directory of Open Access Journals (Sweden)

Xiaojuan Wu

2014-01-01

Full Text Available Diluted magnetic semiconductors Zn1-xFexO nanoparticles with different doping concentration (x=0, 0.01, 0.05, 0.10, and 0.20 were successfully synthesized by hydrothermal method. The crystal structure, morphology, and optical and magnetic properties of the samples were characterized by X-ray diffraction (XRD, energy dispersive spectrometer (EDS, high-resolution transmission electron microscopy (HRTEM, Raman scattering spectra (Raman, photoluminescence spectra (PL, and the vibrating sample magnetometer (VSM. The experiment results show that all samples synthesized by this method possess hexagonal wurtzite crystal structure with good crystallization, no other impurity phases are observed, and the morphology of the sample shows the presence of ellipsoidal nanoparticles. All the Fe3+ successfully substituted for the lattice site of Zn2+ and generates single-phase Zn1-xFexO. Raman spectra shows that the peak shifts to higher frequency. PL spectra exhibit a slight blue shift and the UV emission is annihilated with the increase of Fe3+ concentration. Magnetic measurements indicated that Fe-doped ZnO samples exhibit ferromagnetic behavior at room temperature and the saturation magnetization is enhanced with the increase of iron doping content.

In vitro biological performance of minerals substituted hydroxyapatite coating by pulsed electrodeposition method

Energy Technology Data Exchange (ETDEWEB)

Gopi, Dhanaraj, E-mail: dhanaraj_gopi@yahoo.com [Department of Chemistry, Periyar University, Salem 636 011, Tamilnadu (India); Centre for Nanoscience and Nanotechnology, Periyar University, Salem 636 011, Tamilnadu (India); Karthika, Arumugam; Nithiya, Subramani [Department of Chemistry, Periyar University, Salem 636 011, Tamilnadu (India); Kavitha, Louis [Centre for Nanoscience and Nanotechnology, Periyar University, Salem 636 011, Tamilnadu (India); Department of Physics, Periyar University, Salem 636 011, Tamilnadu (India)

2014-03-01

The present study deals with the optimization of minerals (Sr, Mg and Zn) substituted hydroxyapatite coatings (M-HAP) at different pulse on and off time (1 s, 2 s, 3 s and 4 s) by pulsed electrodeposition method. The formation of M-HAP coating was investigated using Fourier transform infrared spectroscopy (FT-IR) and X-ray diffraction studies (XRD). The morphological features and the content of Sr, Mg and Zn ions in M-HAP coated Ti–6Al–4V were investigated by high resolution scanning electron microscopy (HRSEM) and energy dispersive X-ray analysis (EDAX). The electrochemical studies were performed for M-HAP coated Ti–6Al–4V in simulated body fluid which exhibited better corrosion resistance at the prolonged pulse off time. The in vitro cell adhesion test revealed that the M-HAP coating is found appropriate for the formation of new cell growth which proves the enhanced biocompatible nature of the coating. Thus the M-HAP coating will serve as a potential candidate in orthopedic applications. - Highlights: • We successfully achieved minerals substituted HAP coatings on Ti alloy by PED method. • The M-HAP coated Ti alloy exhibited better bioresistivity in SBF. • The as-coated sample showed antimicrobial activity and better cell viability. • The in vitro test displayed the formation of new cell growth. • The M-HAP coating can serve as a better candidate in orthopedic applications.

Magnetic properties of in-plane oriented barium hexaferrite thin films prepared by direct current magnetron sputtering

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xiaozhi; Yue, Zhenxing, E-mail: yuezhx@mail.tsinghua.edu.cn; Meng, Siqin; Yuan, Lixin [State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China)

2014-12-28

In-plane c-axis oriented Ba-hexaferrite (BaM) thin films were prepared on a-plane (112{sup ¯}0) sapphire (Al{sub 2}O{sub 3}) substrates by DC magnetron sputtering followed by ex-situ annealing. The DC magnetron sputtering was demonstrated to have obvious advantages over the traditionally used RF magnetron sputtering in sputtering rate and operation simplicity. The sputtering power had a remarkable influence on the Ba/Fe ratio, the hematite secondary phase, and the grain morphology of the as-prepared BaM films. Under 80 W of sputtering power, in-plane c-axis highly oriented BaM films were obtained. These films had strong magnetic anisotropy with high hysteresis loop squareness (M{sub r}/M{sub s} of 0.96) along the in-plane easy axis and low M{sub r}/M{sub s} of 0.03 along the in-plane hard axis. X-ray diffraction patterns and pole figures revealed that the oriented BaM films grew via an epitaxy-like growth process with the crystallographic relationship BaM (101{sup ¯}0)//α-Fe{sub 2}O{sub 3}(112{sup ¯}0)//Al{sub 2}O{sub 3}(112{sup ¯}0)

Influences of Ti4+ and Mg2+ substitutions on the properties of lithium ferrites

International Nuclear Information System (INIS)

Su Hua; Zhang Huaiwu; Tang Xiaoli; Liu Baoyuan

2009-01-01

The Ti 4+ and Mg 2+ co-substituted lithium ferrites with different compositions of Zn 0.1 Li 0.45 Mn 0.1 Fe 2.35-2x (TiMg) x O 4 (x=0.0-0.5) were prepared by the ceramic standard processing. The magnetic properties and microstructure of the samples were investigated. A single phase spinel structure was confirmed by XRD in substituting range. Sintering densities continuously decreased with the increase at x value, which was attributed to the fact that the heavier Fe 3+ ions were replaced by the relatively lighter Ti 4+ and Mg 2+ ions. However, relative density of the samples had no obvious relationship with the substituting value. Saturation magnetization continuously decreased with x value, which was attributed to the decrease of resultant magnetic moment between A and B sub-lattice. Remanence decreased monotonously with x value due to the decrease of saturation magnetization and magnetocrystalline anisotropy constant. But the effect of Ti 4+ and Mg 2+ substitutions on the Br/Bs ratio values was not obvious. Coercive force was mainly determined by the microstructure and magnetocrystalline anisotropy constant of the ferrites. In this research, with the increase of Ti 4+ and Mg 2+ substitutions, the advantageous influence by the decrease of magnetocrystalline anisotropy constant was more significant than the disadvantageous influence caused by the increase of closed pores. As a result, coercive force of the ferrites also decreased monotonously with the increase at x value.

Intrinsic and spatially nonuniform ferromagnetism in Co-doped ZnO films

Science.gov (United States)

Tseng, L. T.; Suter, A.; Wang, Y. R.; Xiang, F. X.; Bian, P.; Ding, X.; Tseng, A.; Hu, H. L.; Fan, H. M.; Zheng, R. K.; Wang, X. L.; Salman, Z.; Prokscha, T.; Suzuki, K.; Liu, R.; Li, S.; Morenzoni, E.; Yi, J. B.

2017-09-01

Co doped ZnO films have been deposited by a laser-molecular beam epitaxy system. X-ray diffraction and UV spectra analysis show that Co effectively substitutes the Zn site. Transmission electron microscopy (TEM) and secondary ion mass spectroscopy analysis indicate that there are no clusters. Co dopants are uniformly distributed in ZnO film. Ferromagnetic ordering is observed in all samples deposited under an oxygen partial pressure, PO2=10-3 , 10-5, and 10-7 torr, respectively. However, the magnetization of PO2=10-3 and 10-5 is very small at room temperature. At low temperature, the ferromagnetic ordering is enhanced. Muon spin relaxation (μ SR ) measurements confirm the ferromagnetism in all samples, and the results are consistent with magnetization measurements. From μ SR and TEM analysis, the film deposited under PO2=10-7 torr shows intrinsic ferromagnetism. However, the volume fraction of the ferromagnetism phase is approximately 70%, suggesting that the ferromagnetism is not carrier mediated. Resistivity versus temperature measurements indicate Efros variable range hopping dominates the conductivity. From the above results, we can confirm that a bound magnetic polaron is the origin of the ferromagnetism.

The physic properties of Bi-Zn codoped Y-type hexagonal ferrite

International Nuclear Information System (INIS)

Bai Yang; Zhou Ji; Gui Zhilun; L, Longtu; Qiao Lijie

2008-01-01