Olefins hydro-formylation catalysed by rhodium complexes using ionic liquids; Hydroformylation des olefines par les complexes du rhodium dans les liquides ioniques

Energy Technology Data Exchange (ETDEWEB)

Favre, F.

2000-10-26

Biphasic long chain olefins hydro-formylation catalysed by rhodium complexes using ionic liquids allows a selective reaction and an easy separation of the products from the catalyst. This study reports the synthesis of ionic liquids that were used as the catalyst's solvent. Their physical and chemical properties (melting point, solubility of organic substrates) can be varied with the structure of the organic cation (imidazolium, pyridinium, pyrrolydinium) and with its substituents (nature, length, number). It depends also on the nature of the inorganic anion (hexa-fluoro-phosphate, tetrafluoroborate, tri-fluoro-acetate, triflate, bistriflylamidure...). The use of phosphorus ligands bearing ionic functions proved to be efficient to maintain the onerous rhodium catalyst in the ionic liquid phase. Phosphines, phosphites and phosphinites including anionic (sulfonate, carboxylate) or cationic (imidazolium, pyridinium, guanidinium, phosphonium) groups have been synthesised. Finally, the influences of the ligand and of the ionic liquid on the catalytic system performances are described. Selectivities in aldehydes and reaction rates proved to be highly dependent on the nature of the ligand and of the ionic liquid. The different possibilities of recycling the ionic phase containing the rhodium catalyst have been also studied. (author)

Selectivity of a heterogeneous rhodium catalyst for the carbonylation of monohydric alcohols

Energy Technology Data Exchange (ETDEWEB)

Christensen, B; Scurrell, M S

1977-01-01

Selectivity of a heterogeneous rhodium catalyst for the carbonylation of monohydric alcohols with carbon monoxide in the presence of the corresponding alkyl iodides as promotors was studied in a glass reactor at approx. 0.05:1 alcohol/carbon monoxide ratio. The 1% by wt rhodium-zeolite catalyst was prepared by immersing a Linde molecular sieve zeolite Type 13X in rhodium trichloride at 80/sup 0/C for 15 hr. Methanol was converted to methyl acetate at 433/sup 0/-513/sup 0/K with selectivites > 90% even at the highest temperatures, and dimethyl ether was by-produced. In the absence of methyl iodide, the carbonylation rate decreased drastically but the dehydration was virtually unaffected. The selectivity for ethanol carbonylation decreased from 99% at 383/sup 0/K to 6% at 523/sup 0/K due to the formation of ethylene (predominant at > 470/sup 0/K) and diethyl ether. The only product of the reaction with propan-2-ol studied at 433/sup 0/ or 473/sup 0/K was propene with 100% conversion at 473/sup 0/K. These results are consistent with the relative ease of reactant dehydration on polar catalysts. Table and 13 references.

Effects of human serun albumin in some biological properties of rhodium(II complexes

Directory of Open Access Journals (Sweden)

Espósito Breno P.

2000-01-01

Full Text Available The affinities for human albumin (HSA of five rhodium(II complexes of general formula [Rh2(bridge4] (bridge = acetate, propionate, butyrate, trifluoroacetate and trifluoroacetamidate were determined by spectrophotometry. In the case of the alkylcarboxylates, an inverse correlation of affinity with their liposolubilities was observed. Diffusion of the free or protein-bound complexes into Ehrlich cells in vitro seems to be primarily governed by the hydrophobic character of the complex. The complex [Rh2(tfc4] exhibited affinity towards the protein (K = 214.1 as well as cell partition both in the absence (32.1% and presence (48.6% of HSA. The compound HSA: [Rh2(tfc4] has had its antitumoral action in tumor-bearing Balb-c mice investigated, showing that HSA can be a drug reservoir for the rhodium complex.

A multi-target caffeine derived rhodium(i) N-heterocyclic carbene complex: evaluation of the mechanism of action.

Science.gov (United States)

Zhang, Jing-Jing; Muenzner, Julienne K; Abu El Maaty, Mohamed A; Karge, Bianka; Schobert, Rainer; Wölfl, Stefan; Ott, Ingo

2016-08-16

A rhodium(i) and a ruthenium(ii) complex with a caffeine derived N-heterocyclic carbene (NHC) ligand were biologically investigated as organometallic conjugates consisting of a metal center and a naturally occurring moiety. While the ruthenium(ii) complex was largely inactive, the rhodium(i) NHC complex displayed selective cytotoxicity and significant anti-metastatic and in vivo anti-vascular activities and acted as both a mammalian and an E. coli thioredoxin reductase inhibitor. In HCT-116 cells it increased the reactive oxygen species level, leading to DNA damage, and it induced cell cycle arrest, decreased the mitochondrial membrane potential, and triggered apoptosis. This rhodium(i) NHC derivative thus represents a multi-target compound with promising anti-cancer potential.

Rhodium segregation in dilute silver-rhodium alloys

International Nuclear Information System (INIS)

Krolas, K.; Sternik, M.

1995-01-01

Segregation of Rh in Ag-based alloys has been studied using the perturbed angular correlation of γ-rays emitted in the nuclear decay of radioactive 111 In. The formation of impurity complexes, consisting of an 111 In probe atom and one or more Rh atoms, was observed as a function of annealing time and temperature. Rhodium atom aggregation starts at about 600 K. From the fraction of 111 In bound to isolated Rh atoms the solute rhodium atom concentration was determined. It increases with the nominal alloy concentration up to about 0.04 at.% and then it is essentially constant for the nominal Rh concentration varying between 0.1 and 0.5 at.%. The solute rhodium atom concentration is 3 times larger at the melting point than at 750 K

A MECHANISTIC STUDY OF RHODIUM TRI(ORTHO-TERT-BUTYLPHENYL)PHOSPHITE COMPLEXES AS HYDROFORMYLATION CATALYSTS

NARCIS (Netherlands)

JONGSMA, T; CHALLA, G; VANLEEUWEN, PWNM

1991-01-01

A mechanistic study of the hydroformylation cycle with a rhodium tri(o-t-butylphenyl)phosphite complex as catalyst is presented. Spectroscopic experiments prove that under hydroformylation conditions this complex is coordinated by only one phosphite. The complex has a high activity in the

Molecular metal catalysts on supports: organometallic chemistry meets surface science.

Science.gov (United States)

Serna, Pedro; Gates, Bruce C

2014-08-19

bonding and structure, which identify the supports as ligands with electron-donor properties that influence reactivity and catalysis. Each of the catalyst design variables has been varied independently, illustrated by mononuclear and tetranuclear iridium on zeolite HY and on MgO and by isostructural rhodium and iridium (diethylene or dicarbonyl) complexes on these supports. The data provide examples resolving the roles of the catalyst design variables and place the catalysis science on a firm foundation of organometallic chemistry linked with surface science. Supported molecular catalysts offer the advantages of characterization in the absence of solvents and with surface-science methods that do not require ultrahigh vacuum. Families of supported metal complexes have been made by replacement of ligands with others from the gas phase. Spectroscopically identified catalytic reaction intermediates help to elucidate catalyst performance and guide design. The methods are illustrated for supported complexes and clusters of rhodium, iridium, osmium, and gold used to catalyze reactions of small molecules that facilitate identification of the ligands present during catalysis: alkene dimerization and hydrogenation, H-D exchange in the reaction of H2 with D2, and CO oxidation. The approach is illustrated with the discovery of a highly active and selective MgO-supported rhodium carbonyl dimer catalyst for hydrogenation of 1,3-butadiene to give butenes.

CO hydrogenation on zeolite-supported Ru: Effect of neutralizing cations

International Nuclear Information System (INIS)

Oukaci, R.; Wu, J.C.S.; Goodwin, J.G. Jr.

1986-01-01

Previous results for zeolite-supported Ru prepared by ion exchange suggested a possible effect of the nature and concentration of the neutralizing cations in the zeolite on the catalytic properties of the metal. However, the interpretation of these results was complicated by the fact that a series of zeolites with different Si/Al ratios was used. The present study was undertaken to investigate systematically the influence of the nature of alkali neutralizing cations on CO hydrogenation over ion-exchanged Y-zeolite-supported ruthenium catalysts

Complexes of technetium, rhenium, and rhodium with sexidentate Schiff-base ligands

International Nuclear Information System (INIS)

Hunter, G.; Kilcullen, N.

1989-01-01

The monocationic technetium (IV) and rhenium (IV) complexes with the sexidentate Schiff-base ligands tris[2-(2'-hydroxybenzylideneethyl)]amine and its substituted derivatives have been prepared and their electrochemical properties studied. The variable-temperature 90.6 MHz 13 C-{ 1 H} n.m.r. spectrum of the rhodium (III) complex of tris[2-(2-hydroxy-5'-isopropylbenzylideneethyl)-amine] has been observed, indicating fluxionality at temperatures above 218 K. (author)

The liquid-liquid extraction of chloro-(trichlorostannato)-rhodium(I/III) and -ruthenium (II) complexes from dilute hydrochloric acid into 4-methylpentan-2-one

International Nuclear Information System (INIS)

Wyrley-Birch, J.M.

1984-10-01

The effect of stannous chloride on the liquid-liquid extraction of rhodium and ruthenium from hydrochloric acid solutions into 4-methyl-pentan-2-one (MIBK)/hexane mixtures was studied in detail. Stannous chloride concentrations were found to considerably increase the efficiency of the extraction of rhodium and ruthenium into the organic phase. Chloro-(trichlorostannato)-rhodium (I/III) complexes were formed at room temperature. The rate of chloro-(trichlorostannato)-ruthenium (II) complex formation was extremely slow at room temperature, but increased on heating of the aqueous solutions. The amount of rhodium and ruthenium extracted into the organic phase depend on the Sn(II):M molar ratio, the HCl, H sup(+) and Cl sup(-) concentrations, as well as the equilibration time. A 119 Sn NMR study of the MIBK extracts, showed that the stoichiometry of the chloro-(trichlorostannato)-rhodium (I/III) complexes extracted into the organic phase was dependent on the Sn(II):Rh(III) molar ratio as well as the HCl, H sup(+) and Cl sup(-) concentrations in the aqueous phase. The predominant species observed in the organic phase from HCl solutions containing Sn(II):Rh(III) ratios >= 5:1, was shown to be an hydrido complex having the form [RhH(SnCl 3 ) 4 Cl] 3 sup(-) or [RhH(SnCl 3 ) 4 ]2 sup(-). An essentially quantitative separation of rhodium and ruthenium was achieved utilising the variation in the rates of rhodium-tin and ruthenium-tin complex formation

Bimetallic poly- and oligo-nuclear complexes based on a rhodium(III) metalloligand

Science.gov (United States)

Vasilchenko, Danila B.; Venediktov, Anatoliy B.; Korenev, Sergey V.; Filatov, Evgeniy Yu.; Baidina, Iraida A.; Nadolinnyi, Vladimir A.

2012-10-01

Interaction of trans-[Rh(i-Nic)4Cl2]3- anions (i-Nic- - isonicotinate anion) with Cuaq2+ and Coaq2+ cations in water has afforded complex salts Co3[Rh(i-Nic)4Cl2]2·17H2O (1) and Cu3[Rh(i-Nic)4Cl2]2·14H2O (2). Oligonuclear character of 1 and 2 has been established. A coordination polymer Cu5[Rh(i-Nic)4Cl2]2(i-Nic)2(OH)2·2H2O (3) has been crystallized by hydrothermal treatment of 2 at 160 °C, and its structure was determined by X-ray structural analysis. EPR data for the complexes has been collected and interpreted. Thermal decomposition of the salts was studied by c-DTA. Bimetallic alloys rhodium-copper and rhodium-cobalt have been obtained as final products of thermal decomposition.

Hydrolysis of Letrozole catalyzed by macrocyclic Rhodium (I) Schiff-base complexes.

Science.gov (United States)

Reddy, P Muralidhar; Shanker, K; Srinivas, V; Krishna, E Ravi; Rohini, R; Srikanth, G; Hu, Anren; Ravinder, V

2015-03-15

Ten mononuclear Rhodium (I) complexes were synthesized by macrocyclic ligands having N4 and N2O2 donor sites. Square planar geometry is assigned based on the analytical and spectral properties for all complexes. Rh(I) complexes were investigated as catalysts in hydrolysis of Nitrile group containing pharmaceutical drug Letrozole. A comparative study showed that all the complexes are efficient in the catalysis. The percent yields of all the catalytic reaction products viz. drug impurities were determined by spectrophotometric procedures and characterized by spectral studies. Copyright © 2014 Elsevier B.V. All rights reserved.

Hydroformylation of methyl oleate catalyzed by rhodium complexes; Hidroformilacao do oleato de metila catalisada por complexos de rodio

Energy Technology Data Exchange (ETDEWEB)

Mendes, Ana Nery Furlan [Universidade Federal do Espirito Santo (UFES), Sao Mateus, ES (Brazil). Centro Universitario Norte do Espirito Santo. Dept. de Ciencias Naturais; Rosa, Ricardo Gomes da; Gregorio, Jose Ribeiro, E-mail: jrg@iq.ufrgs.br [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Inst. de Quimica

2012-07-01

In this work, we describe the hydroformylation of methyl oleate catalyzed by several rhodium complexes. Parameters including total pressure, phosphorous/rhodium and CO/H{sub 2} ratio, temperature and phosphorous ligands were scanned. Total conversion of the starting double bonds was achieved while maintaining excellent selectivity in aldehydes. (author)

Supported Zeolite Beta Layers via an Organic Template-Free Preparation Route

Directory of Open Access Journals (Sweden)

Stephanie Reuss

2018-01-01

Full Text Available Layers of high silica zeolites, synthesized with an organic structure directing agent (OSDA and grown onto porous support structures, frequently suffer from the thermal stress during the removal of OSDA via the calcination process. The different thermal expansion coefficients of the zeolite and the support material, especially when stainless steel is used as a support, causes enormous tension resulting in defect formation in the zeolite layer. However, the calcination is an easy procedure to decompose the OSDA in the pore system of the zeolite. Recently, methods to synthesize zeolite beta without the use of an organic structure directing agent have been described. In the present study, a seed-directed synthesis is used to prepare OSDA-free zeolite beta layers on stainless steel supports via an in situ preparation route. For the application as membrane, a porous stainless steel support has been chosen. The beta/stainless steel composites are characterized by X-ray diffraction (XRD and scanning electron microscopy (SEM. To prove its possible application as a membrane, the beta/stainless steel composites were also tested by single gas permeances of H2, He, CO2, N2, and CH4.

Supported Zeolite Beta Layers via an Organic Template-Free Preparation Route.

Science.gov (United States)

Reuss, Stephanie; Sanwald, Dirk; Schülein, Marion; Schwieger, Wilhelm; Al-Thabaiti, Shaeel A; Mokhtar, Mohamed; Basahel, Sulaiman N

2018-01-21

Layers of high silica zeolites, synthesized with an organic structure directing agent (OSDA) and grown onto porous support structures, frequently suffer from the thermal stress during the removal of OSDA via the calcination process. The different thermal expansion coefficients of the zeolite and the support material, especially when stainless steel is used as a support, causes enormous tension resulting in defect formation in the zeolite layer. However, the calcination is an easy procedure to decompose the OSDA in the pore system of the zeolite. Recently, methods to synthesize zeolite beta without the use of an organic structure directing agent have been described. In the present study, a seed-directed synthesis is used to prepare OSDA-free zeolite beta layers on stainless steel supports via an in situ preparation route. For the application as membrane, a porous stainless steel support has been chosen. The beta/stainless steel composites are characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). To prove its possible application as a membrane, the beta/stainless steel composites were also tested by single gas permeances of H₂, He, CO₂, N₂, and CH₄.

Geometry and Framework Interactions of Zeolite-Encapsulated Copper(II)-Histidine Complexes

NARCIS (Netherlands)

Weckhuysen, B.M.; Grommen, R.; Manikandan, P.; Gao, Y.; Shane, T.; Shane, J.J.; Schoonheydt, R.A.; Goldfarb, D.

2000-01-01

The coordination geometry of zeolite-encapsulated copper(II)-histidine (CuHis) complexes, prepared by ion exchange of the complexes from aqueous solutions into zeolite NaY, was determined by a combination of UV-vis-NIR diffuse reflectance spectroscopy (DRS), X-band EPR, electron-spin-echo envelope

A rhodium(III) complex inhibits LPS-induced nitric oxide production and angiogenic activity in cellulo.

Science.gov (United States)

Liu, Li-Juan; Lin, Sheng; Chan, Daniel Shiu-Hin; Vong, Chi Teng; Hoi, Pui Man; Wong, Chun-Yuen; Ma, Dik-Lung; Leung, Chung-Hang

2014-11-01

Metal-containing complexes have arisen as viable alternatives to organic molecules as therapeutic agents. Metal complexes possess a number of advantages compared to conventional carbon-based compounds, such as distinct geometries, interesting electronic properties, variable oxidation states and the ability to arrange different ligands around the metal centre in a precise fashion. Meanwhile, nitric oxide (NO) plays key roles in the regulation of angiogenesis, vascular permeability and inflammation. We herein report a novel cyclometalated rhodium(III) complex as an inhibitor of lipopolysaccharides (LPS)-induced NO production in RAW264.7 macrophages. Experiments suggested that the inhibition of NO production in cells by complex 1 was mediated through the down-regulation of nuclear factor-κB (NF-κB) activity. Furthermore, complex 1 inhibited angiogenesis in human umbilical vein endothelial cells (HUVECs) as revealed by an endothelial tube formation assay. This study demonstrates that kinetically inert rhodium(III) complexes may be potentially developed as effective anti-angiogenic agents. Copyright © 2014 Elsevier Inc. All rights reserved.

Intramolecular Hydroamination of Unbiased and Functionalized Primary Aminoalkenes Catalyzed by a Rhodium Aminophosphine Complex

Science.gov (United States)

Julian, Lisa D.; Hartwig, John F.

2010-01-01

We report a rhodium catalyst that exhibits high reactivity for the hydroamination of primary aminoalkenes that are unbiased toward cyclization and that possess functional groups that would not be tolerated in hydroaminations catalyzed by more electrophilic systems. This catalyst contains an unusual diaminophosphine ligand that binds to rhodium in a κ3-P,O,P mode. The reactions catalyzed by this complex typically proceed at mild temperatures (room temperature to 70 °C), occur with primary aminoalkenes lacking substituents on the alkyl chain that bias the system toward cyclization, occur with primary aminoalkenes containing chloride, ester, ether, enolizable ketone, nitrile, and unprotected alcohol functionality, and occur with primary aminoalkenes containing internal olefins. Mechanistic data imply that these reactions occur with a turnover-limiting step that is different from that of reactions catalyzed by late transition metal complexes of Pd, Pt, and Ir. This change in the turnover-limiting step and resulting high activity of the catalyst stem from favorable relative rates for protonolysis of the M-C bond to release the hydroamination product vs reversion of the aminoalkyl intermediate to regenerate the acyclic precursor. Probes for the origin of the reactivity of the rhodium complex of L1 imply that the aminophosphine groups lead to these favorable rates by effects beyond steric demands and simple electron donation to the metal center. PMID:20839807

In Situ Structure-Function Studies of Oxide Supported Rhodium Catalysts by Combined Energy Dispersive XAFS and DRIFTS Spectroscopies

International Nuclear Information System (INIS)

Evans, John; Dent, Andrew J.; Diaz-Moreno, Sofia; Fiddy, Steven G.; Jyoti, Bhrat; Tromp, Moniek; Newton, Mark A.

2007-01-01

The techniques of energy dispersive EXAFS (EDE), diffuse reflectance Fourier transform infrared spectroscopy (DRIFTS) and mass spectrometry (MS) have been combined to study the structure and function of an oxide supported metal catalyst, namely 5 wt% Rh/Al2O3. Using a FreLoN camera as the EDE detector and a rapid-scanning IR spectrometer, experiments could be performed with a repetition rate of 50 ms. The results show that the nature of the rhodium centers is a function of the partial pressures of the reacting gases (CO and NO) and also temperature. This combination of gases oxidizes metallic rhodium particles to Rh(CO)2 at room temperature. The proportion of the rhodium adopting this site increases as the temperature is raised (up to 450 K). Above that temperature the dicarbonyl decomposes and the metal reclusters. Once this condition is met, catalysis ensues. Gas switching techniques show that at 573 K with NO in excess, the clusters can be oxidized rapidly to afford a linear nitrosyl complex; re-exposure to CO also promotes reclustering and the CO adopts terminal (atop) and bridging (2-fold) sites

Examining Rhodium Catalyst complexes for Use with Conducting Polymers Designed for Fuel Cells in Preparing Biosensors

Energy Technology Data Exchange (ETDEWEB)

Carpio, M.M.; Kerr, J.B.

2005-01-01

Biosensing devices are important because they can detect, record, and transmit information regarding the presence of, or physiological changes in, different chemical or biological materials in the environment. The goal of this research is to prepare a biosensing device that is effective, quick, and low cost. This is done by examining which chemicals will work best when placed in a biosensor. The first study involved experimenting on a rhodium catalyst complexed with ligands such as bipyridine and imidazole. The rhodium catalyst is important because it is reduced from RhIII to RhI, forms a hydride by reaction with water and releases the hydride to react with nicotinamide adenine dinucleotide (NAD+) to selectively produce 1,4-NADH, the reduced form of NAD+. The second study looked at different types of ketones and enzymes for the enzyme-substrate reaction converting a ketone into an alcohol. Preliminary results showed that the rhodium complexed with bipyridine was able to carry out all the reactions, while the rhodium complexed with imidazole was not able to produce and release hydrides. In addition, the most effective ketone to use is benzylacetone with the enzyme alcohol dehydrogenase from baker’s yeast. Future work includes experimenting with bis-imidazole, which mimics the structure of bipyridine to see if it has the capability to reduce and if the reduction rate is comparable to the bipyridine complex. Once all testing is completed, the fastest catalysts will be combined with polymer membranes designed for fuel cells to prepare biosensing devices that can be used in a variety of applications including ones in the medical and environmental fields.

Biotemplating of Luffa cylindrica sponges to self-supporting hierarchical zeolite macrostructures for bio-inspired structured catalytic reactors

International Nuclear Information System (INIS)

Zampieri, Alessandro; Mabande, Godwin T.P.; Selvam, Thangaraj; Schwieger, Wilhelm; Rudolph, Alexander; Hermann, Ralph; Sieber, Heino; Greil, Peter

2006-01-01

Biomorphic self-supporting MFI-type zeolite frameworks with hierarchical porosity and complex architecture were prepared using a 2-step (in-situ seeding and secondary crystal growth) hydrothermal synthesis in the presence of a biological template (Luffa sponge), employed as a macroscale sacrificial structure builder. The bio-inspired zeolitic replica inherited the complex spongy morphology and the intricate open-porous architecture of the biotemplate. Moreover, it exhibited reasonable mechanical stability in order to study the applicability of the biomorphic catalyst in a technical catalytic process. A bio-inspired catalytic reactor utilising the self-supporting ZSM-5 scaffold in monolithic configuration was developed in order to test the catalytic performance of the material

Oligomeric complexes of some heteroaromatic ligands and aromatic diamines with rhodium and molybdenum tetracarboxylates: 13C and 15N CPMAS NMR and density functional theory studies.

Science.gov (United States)

Leniak, Arkadiusz; Kamieński, Bohdan; Jaźwiński, Jarosław

2015-05-01

Seven new oligomeric complexes of 4,4'-bipyridine; 3,3'-bipyridine; benzene-1,4-diamine; benzene-1,3-diamine; benzene-1,2-diamine; and benzidine with rhodium tetraacetate, as well as 4,4'-bipyridine with molybdenum tetraacetate, have been obtained and investigated by elemental analysis and solid-state nuclear magnetic resonance spectroscopy, (13)C and (15)N CPMAS NMR. The known complexes of pyrazine with rhodium tetrabenzoate, benzoquinone with rhodium tetrapivalate, 4,4'-bipyridine with molybdenum tetrakistrifluoroacetate and the 1 : 1 complex of 2,2'-bipyridine with rhodium tetraacetate exhibiting axial-equatorial ligation mode have been obtained as well for comparison purposes. Elemental analysis revealed 1 : 1 complex stoichiometry of all complexes. The (15)N CPMAS NMR spectra of all new complexes consist of one narrow signal, indicating regular uniform structures. Benzidine forms a heterogeneous material, probably containing linear oligomers and products of further reactions. The complexes were characterized by the parameter complexation shift Δδ (Δδ = δcomplex  - δligand). This parameter ranged from around -40 to -90 ppm in the case of heteroaromatic ligands, from around -12 to -22 ppm for diamines and from -16 to -31 ppm for the complexes of molybdenum tetracarboxylates with 4,4'-bipyridine. The experimental results have been supported by a density functional theory computation of (15)N NMR chemical shifts and complexation shifts at the non-relativistic Becke, three-parameter, Perdew-Wang 91/[6-311++G(2d,p), Stuttgart] and GGA-PBE/QZ4P levels of theory and at the relativistic scalar and spin-orbit zeroth order regular approximation/GGA-PBE/QZ4P level of theory. Nucleus-independent chemical shifts have been calculated for the selected compounds. Copyright © 2015 John Wiley & Sons, Ltd.

Interfacial bonding stabilizes rhodium and rhodium oxide nanoparticles on layered Nb oxide and Ta oxide supports.

Science.gov (United States)

Strayer, Megan E; Binz, Jason M; Tanase, Mihaela; Shahri, Seyed Mehdi Kamali; Sharma, Renu; Rioux, Robert M; Mallouk, Thomas E

2014-04-16

Metal nanoparticles are commonly supported on metal oxides, but their utility as catalysts is limited by coarsening at high temperatures. Rhodium oxide and rhodium metal nanoparticles on niobate and tantalate supports are anomalously stable. To understand this, the nanoparticle-support interaction was studied by isothermal titration calorimetry (ITC), environmental transmission electron microscopy (ETEM), and synchrotron X-ray absorption and scattering techniques. Nanosheets derived from the layered oxides KCa2Nb3O10, K4Nb6O17, and RbTaO3 were compared as supports to nanosheets of Na-TSM, a synthetic fluoromica (Na0.66Mg2.68(Si3.98Al0.02)O10.02F1.96), and α-Zr(HPO4)2·H2O. High surface area SiO2 and γ-Al2O3 supports were also used for comparison in the ITC experiments. A Born-Haber cycle analysis of ITC data revealed an exothermic interaction between Rh(OH)3 nanoparticles and the layered niobate and tantalate supports, with ΔH values in the range -32 kJ·mol(-1) Rh to -37 kJ·mol(-1) Rh. In contrast, the interaction enthalpy was positive with SiO2 and γ-Al2O3 supports. The strong interfacial bonding in the former case led to "reverse" ripening of micrometer-size Rh(OH)3, which dispersed as 0.5 to 2 nm particles on the niobate and tantalate supports. In contrast, particles grown on Na-TSM and α-Zr(HPO4)2·H2O nanosheets were larger and had a broad size distribution. ETEM, X-ray absorption spectroscopy, and pair distribution function analyses were used to study the growth of supported nanoparticles under oxidizing and reducing conditions, as well as the transformation from Rh(OH)3 to Rh nanoparticles. Interfacial covalent bonding, possibly strengthened by d-electron acid/base interactions, appear to stabilize Rh(OH)3, Rh2O3, and Rh nanoparticles on niobate and tantalate supports.

Performance Evaluations of Ion Exchanged Zeolite Membranes on Alumina Supports

Energy Technology Data Exchange (ETDEWEB)

Bhave, Ramesh R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jubin, Robert Thomas [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Spencer, Barry B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nair, Sankar [Georgia Inst. of Technology, Atlanta, GA (United States)

2017-08-27

This report describes the synthesis and evaluation of molecular sieve zeolite membranes to separate and concentrate tritiated water (HTO) from dilute HTO-bearing aqueous streams. In the first phase of this effort, several monovalent and divalent cation-exchanged silico alumino phosphate (SAPO-34) molecular sieve zeolite membranes were synthesized on disk supports and characterized with gas and vapor permeation measurements. In the second phase, Linde Type A (LTA) zeolite membranes were synthesized in disk and tubular supports. The pervaporation process performance was evaluated for the separation and concentration of tritiated water.

Halloysite nanotube-based electrospun ceramic nanofibre mat: a novel support for zeolite membranes

Science.gov (United States)

Chen, Zhuwen; Zeng, Jiaying; Lv, Dong; Gao, Jinqiang; Zhang, Jian; Bai, Shan; Li, Ruili; Hong, Mei; Wu, Jingshen

2016-12-01

Some key parameters of supports such as porosity, pore shape and size are of great importance for fabrication and performance of zeolite membranes. In this study, we fabricated millimetre-thick, self-standing electrospun ceramic nanofibre mats and employed them as a novel support for zeolite membranes. The nanofibre mats were prepared by electrospinning a halloysite nanotubes/polyvinyl pyrrolidone composite followed by a programmed sintering process. The interwoven nanofibre mats possess up to 80% porosity, narrow pore size distribution, low pore tortuosity and highly interconnected pore structure. Compared with the commercial α-Al2O3 supports prepared by powder compaction and sintering, the halloysite nanotube-based mats (HNMs) show higher flux, better adsorption of zeolite seeds, adhesion of zeolite membranes and lower Al leaching. Four types of zeolite membranes supported on HNMs have been successfully synthesized with either in situ crystallization or a secondary growth method, demonstrating good universality of HNMs for supporting zeolite membranes.

Immobilization of rhodium complexes at thiolate monolayers on gold surfaces : Catalytic and structural studies

NARCIS (Netherlands)

Belser, T; Stöhr, Meike; Pfaltz, A

2005-01-01

Chiral rhodium-diphosphine complexes have been incorporated into self-assembled thiolate monolayers (SAMS) on gold colloids. Catalysts of this type are of interest because they combine properties of homogeneous and heterogeneous systems. In addition, it should be possible to influence the catalytic

Crystallization and melting behavior of isotactic polypropylene composites filled by zeolite supported β-nucleator

International Nuclear Information System (INIS)

Jiang, Juan; Li, Gu; Tan, Nanshu; Ding, Qian; Mai, Kancheng

2012-01-01

Highlights: ► The supported calcium pimelate β-zeolite was prepared. ► The β-nucleation of zeolite was enhanced dramatically through reaction. ► High β-phase content iPP composites were obtained by introducing the β-zeolite into iPP. - Abstract: In order to prepare the zeolite filled β-iPP composites, the calcium pimelate as β-nucleator supported on the surface of zeolite (β-zeolite) was prepared by the interaction between calcified zeolite and pimelic acid. The β-nucleation, crystallization behavior and melting characteristic of zeolite, calcified zeolite and β-zeolite filled iPP composites were investigated by differential scanning calorimetry and wide-angle X-ray diffractometer. The results indicated that addition of the zeolite and calcified zeolite as well as β-zeolite increased the crystallization temperature of iPP. The zeolite and calcified zeolite filled iPP composites mainly crystallized in the α-crystal form and the strong β-heterogeneous nucleation of β-zeolite results in the formation of only β-crystal in β-zeolite filled iPP composites. The zeolite filled β-iPP composites with high β-crystal contents (above 0.90) can be easily obtained by adding β-zeolite into iPP matrix.

Complexation of rhodium(II) tetracarboxylates with aliphatic diamines in solution: 1H and 13C NMR and DFT investigations.

Science.gov (United States)

Jaźwiński, Jarosław; Sadlej, Agnieszka

2013-10-01

The complexation of rhodium(II) tetraacetate, tetrakistrifluoroaceate and tetrakisoctanoate with a set of diamines (ethane-1,diamine, propane-1,3-diamine and nonane-1,9-diamine) and their N,N'-dimethyl and N,N,N',N'-tetramethyl derivatives in chloroform solution has been investigated by (1) H and (13) C NMR spectroscopy and density functional theory (DFT) modelling. A combination of two bifunctional reagents, diamines and rhodium(II) tetracarboxylates, yielded insoluble coordination polymers as main products of complexation and various adducts in the solution, being in equilibrium with insoluble material. All diamines initially formed the 2 : 1 (blue), (1 : 1)n oligomeric (red) and 1 : 2 (red) axial adducts in solution, depending on the reagents' molar ratio. Adducts of primary and secondary diamines decomposed in the presence of ligand excess, the former via unstable equatorial complexes. The complexation of secondary diamines slowed down the inversion at nitrogen atoms in NH(CH3 ) functional groups and resulted in the formation of nitrogenous stereogenic centres, detectable by NMR. Axial adducts of tertiary diamines appeared to be relatively stable. The presence of long aliphatic chains in molecules (adducts of nonane-1,9-diamines or rhodium(II) tetrakisoctanoate) increased adduct solubility. Hypothetical structures of the equatorial adduct of rhodium(II) tetraacetate with ethane-1,2-diamine and their NMR parameters were explored by means of DFT calculations. Copyright © 2013 John Wiley & Sons, Ltd.

Synthesis and characterization of Fe(III-piperazine-derived complexes encapsulated in zeolite Y

Directory of Open Access Journals (Sweden)

Márcio E. Berezuk

2012-01-01

Full Text Available Zeolite-encapsulated complexes have been widely applied in hydrocarbon oxidation catalysis. The "ship-in-a-bottle" encapsulation of iron(III complexes containing piperazine and piperazine-derivative ligands in zeolite-Y is described. The flexible ligand methodology was employed and the efficiency and reproducibility of the procedure was investigated. The catalysts were characterized employing several techniques and the results indicate the presence of coordinated and uncoordinated iron(III ions inside and outside the zeolitic cage.

Electrochemical water splitting using nano-zeolite Y supported tungsten oxide electrocatalysts

Science.gov (United States)

Anis, Shaheen Fatima; Hashaikeh, Raed

2018-02-01

Zeolites are often used as supports for metals and metal oxides because of their well-defined microporous structure and high surface area. In this study, nano-zeolite Y (50-150 nm range) and micro-zeolite Y (500-800 nm range) were loaded with WO3, by impregnating the zeolite support with ammonium metatungstate and thermally decomposing the salt thereafter. Two different loadings of WO3 were studied, 3 wt.% and 5 wt.% with respect to the overall catalyst. The prepared catalysts were characterized for their morphology, structure, and surface areas through scanning electron microscope (SEM), XRD, and BET. They were further compared for their electrocatalytic activity for hydrogen evolution reaction (HER) in 0.5 M H2SO4. On comparing the bare micro-zeolite particles with the nano-form, the nano-zeolite Y showed higher currents with comparable overpotentials and lower Tafel slope of 62.36 mV/dec. WO3 loading brought about a change in the electrocatalytic properties of the catalyst. The overpotentials and Tafel slopes were observed to decrease with zeolite-3 wt.% WO3. The smallest overpotential of 60 mV and Tafel slope of 31.9 mV/dec was registered for nano-zeolite with 3 wt.% WO3, while the micro-zeolite gave an overpotential of 370 mV and a Tafel slope of 98.1 mV/dec. It was concluded that even with the same metal oxide loading, nano-zeolite showed superior performance, which is attributed to its size and hence easier escape of hydrogen bubbles from the catalyst.

Supported Rh-phosphine complex catalysts for continuous gas-phase decarbonylation of aldehydes

DEFF Research Database (Denmark)

Malcho, Phillip; Garcia-Suarez, Eduardo J.; Mentzel, Uffe Vie

2014-01-01

Heterogeneous silica supported rhodium-phosphine complex catalysts are employed for the first time in the catalytic decarbonylation of aldehydes in continuous gas-phase. The reaction protocol is exemplified for the decarbonylation of p-tolualdehyde to toluene and further extended to other aromatic...

Hydroformylation and kinetics of 1-hexene over ruthenium, cobalt and rhodium zerolite catalysts

International Nuclear Information System (INIS)

Wang, C.; Wei, W.

1989-01-01

In this paper, six kinds of catalysts were prepared by cation exchange with rhodium, ruthenium and cobalt chloropentaamino dichoride and zeolites. Effects such as support materials, PPH 3 to metal ratio, reaction temperature, total pressure, H 2 /CO ratio, reaction time and solvents have been investigated in an autoclave. The most favorable results of 1-hexene hydroformylation were obtained in the temperature range 100-150 degrees C at a pressure of 5.0MPa (H 2 /CO=1:1) and the addition of free PPh 3 . The bimetallic catalysts showed high catalytic activing for hydroformylation because of the synergistic effect of bimetallic systems. This paper reports the results of experiments and catalysts characterization by means of IR and XRD spectroscopy

Rhodium, iridium and nickel complexes with a 1,3,5-triphenylbenzene tris-MIC ligand. Study of the electronic properties and catalytic activities

Directory of Open Access Journals (Sweden)

Carmen Mejuto

2015-12-01

Full Text Available The coordination versatility of a 1,3,5-triphenylbenzene-tris-mesoionic carbene ligand is illustrated by the preparation of complexes with three different metals: rhodium, iridium and nickel. The rhodium and iridium complexes contained the [MCl(COD] fragments, while the nickel compound contained [NiCpCl]. The preparation of the tris-MIC (MIC = mesoionic carbene complex with three [IrCl(CO2] fragments, allowed the estimation of the Tolman electronic parameter (TEP for the ligand, which was compared with the TEP value for a related 1,3,5-triphenylbenzene-tris-NHC ligand. The electronic properties of the tris-MIC ligand were studied by cyclic voltammetry measurements. In all cases, the tris-MIC ligand showed a stronger electron-donating character than the corresponding NHC-based ligands. The catalytic activity of the tri-rhodium complex was tested in the addition reaction of arylboronic acids to α,β-unsaturated ketones.

Complexation of diphenyl(phenylacetenyl)phosphine to rhodium(III) tetraphenyl porphyrins

DEFF Research Database (Denmark)

Stulz, Eugen; Scott, Sonya M; Bond, Andrew D

2003-01-01

). The methylide on rhodium in 3 is not displaced, leading selectively to the mono-phosphine complex (DPAP)(Me)Rh(TPP) (5). The first and second association constants, as determined by isothermal titration calorimetry and UV-vis titrations, are in the range 10(4)-10(7) M(-1) (in CH(2)Cl(2)). Using LDI-TOF mass....... The largest values of DeltaG degrees are found for 6. The thermodynamic and UV-vis data reveal that the methylide and the phosphine ligand have an almost identical electronic trans-influence on the sixth ligand....

Templating mesoporous zeolites

DEFF Research Database (Denmark)

Egeblad, Kresten; Christensen, Christina Hviid; Kustova, Marina

2008-01-01

The application of templating methods to produce zeolite materials with hierarchical bi- or trimodal pore size distributions is reviewed with emphasis on mesoporous materials. Hierarchical zeolite materials are categorized into three distinctly different types of materials: hierarchical zeolite...... crystals, nanosized zeolite crystals, and supported zeolite crystals. For the pure zeolite materials in the first two categories, the additional meso- or macroporosity can be classified as being either intracrystalline or intercrystalline, whereas for supported zeolite materials, the additional porosity...... originates almost exclusively from the support material. The methods for introducing mesopores into zeolite materials are discussed and categorized. In general, mesopores can be templated in zeolite materials by use of solid templating, supramolecular templating, or indirect templating...

Controlled Oxygen Chemisorption on an Alumina Supported Rhodium Catalyst. The Formation of a New Metal-Metal Oxide Interface Determined with EXAFS.

NARCIS (Netherlands)

Koningsberger, D.C.; Martens, J.H.A.; Prins, R.

1989-01-01

An alumina-supported rhodium catalyst has been studied with EXAFS. After reduction and evacuation, oxygen was admitted at 100 and 300 K. EXAFS spectra of the catalyst after oxygen admission at 100 K indicated the beginning of oxidation. At 300 K only a small part of the rhodium particles remained

Dinuclear ditertiary phosphite derivatives of rhodium

International Nuclear Information System (INIS)

Meintjies, E.

1981-08-01

The overall objective of the research described in this thesis was the design, synthesis, characterization and chemistry of dinuclear complexes of rhodium in which the metal atoms are held in close proximity to each other. Complexes of this nature are of considerable interest owing, in part, to their potential as models for multicentred metal catalysts, as well as to the highly novel and unusual chemistry already discovered for a number of them. A survey of dinuclear complexes of rhodium containing carbonyl and group V donor ligands has been presented as a background introduction to the research reported in this thesis. The coordination behaviour of the diphosphazane ligands, (RO) 2 PN(R')P(OR) 2 (R=Ph or Me, R' = Et; R = Et or Pr/i, R' = Me), and the ditertiary phosphite ligand, (EtO) 2 POP(OEt) 2 , towards certain rhodium precursors has been investigated. A number of highly unusual neutral dinuclear complexes of rhodium, in which these ligands bridge-bond the two rhodium atoms, have been synthesized. Two types of monocarbonyl decarbonylation products are observed for compounds of the type, [Rh 2 Cl 2 (CO) 2 (μ-diphosphazane) 2 ]. 1 H and 31 P[ 1 H] n.m.r. spectral studies have been carried out with the object of establishing the nature of the bridging halogen ligands in the tricarbonyl species. Asymetric zerovalent dinuclear species of the type, [Rh 2 (CO) 3 -[μ-(RO) 2 PN(R')P(OR) 2 ] 2 ] (R = Ph or Me, R' = Et; R = Pr/i, R' = Me), are obtained. A single crystal X-ray analysis has been carried out. Homoleptic cationic species are obtained by reaction of the alkoxydiphosphazane ligands with [Rh(C 8 H 12 )(solvent)(n)] + under the appropriate reaction conditions. The solution and solid-state infrared spectra and the 31 P[ 1 H] n.m.r. spectra of all new compounds synthesized in this study are discussed in terms of possible structures for these compounds. Where appropriate, the n.m.r. spectral data are also discussed in terms of fluxional behaviour

Reactivity of rhodium during co-deposition of rhodium and carbon

International Nuclear Information System (INIS)

Marot, Laurent; Steiner, Roland; De Temmerman, Gregory; Oelhafen, Peter

2009-01-01

The detailed characterizations of rhodium/carbon films prepared by co-deposition using a dual magnetron sputtering have been carried out on silicon substrates at room temperature. Effects of the carbon incorporated in the film on the chemical bonding state, optical reflectivity and crystallinity were investigated using XPS, reflectivity measurements, XRD and SEM. The incorporation of carbon changes the films' crystallinity and thus producing amorphous films. The reflectivity of the films decreases linearly as the rhodium concentration decreases. It is important to note that no chemical bonding was observed between rhodium and carbon whatever the deposition conditions, even at high deposition temperature. Concerning the reactivity of rhodium films with oxygen, after long term storage in air the rhodium surface is covered with a thin rhodium oxide (few nanometers). However, for these films no variation of the optical reflectivity was observed after long air storage.

Rhodium(I) catalysis in olefin photoreactions

International Nuclear Information System (INIS)

Salomon, R.G.; El Sanadi, N.

1975-01-01

The photorearrangement (254 nm) of 1,5-cyclooctadiene (1) in the presence of rhodium(I) chloride to give 1,4-cyclooctadiene (4) was found by deuterium labeling to involve an intramolecular [1,3] shift of hydrogen. A rate-determining cleavage of an allylic C--H bond is indicated by a deuterium isotope effect, k/sub H//k/sub D/ = 1.55 +- 0.03 for the 1 → 4 rearrangement. The acyclic 1,5-diene, 3,3-dimethyl-1,5-hexadiene (8), rearranges in the presence of rhodium(I) chloride upon uv irradiation (254 nm) to give cis-3,3-dimethyl-1,4-hexadiene (10) and the trans isomer 11 in a 1:4 ratio, respectively. This observation supports a mechanism for the photorearrangement of olefins catalyzed by rhodium(I) involving an initial photodissociation of one of two rhodium(I) coordinated carbon-carbon double bonds. This results in an increase in the coordinative unsaturation of rhodium(I) and enhances the proclivity of this d/sub s/ metal atom toward oxidative addition of an allylic C--H bond. A eta 3 -allylrhodium hydride intermediate then gives rearranged olefin by reductive elimination. Lastly, a novel photochemical, rhodium(I) catalyzed hydrogen transfer is reported which gives cyclooctene (7) from cyclooctadienes under unprecedentedly mild conditions. (auth)

Design and fabrication of zeolite macro- and micromembranes

Science.gov (United States)

Chau, Lik Hang Joseph

2001-07-01

The chemical nature of the support surface influences zeolite nucleation, crystal growth and elm adhesion. It had been demonstrated that chemical modification of support surface can significantly alter the zeolite film and has a good potential for large-scale applications for zeolite membrane production. The incorporation of titanium and vanadium metal ions into the structural framework of MFI zeolite imparts the material with catalytic properties. The effects of silica and metal (i.e., Ti and V) content, template concentration and temperature on the zeolite membrane growth and morphology were investigated. Single-gas permeation experiments were conducted for noble gases (He and Ar), inorganic gases (H2, N2, SF6) and hydrocarbons (methane, n-C4, i-C4) to determine the separation performance of these membranes. Using a new fabrication method based on microelectronic fabrication and zeolite thin film technologies, complex microchannel geometry and network (supported zeolite films. The zeolite micropatterns were stable even after repeated thermal cycling between 303 K and 873 K for prolonged periods of time. This work also demonstrates that zeolites (i.e., Sil-1, ZSM-5 and TS-1) can be employed as catalyst, membrane or structural materials in miniature chemical devices. Traditional semiconductor fabrication technology was employed in micromachining the device architecture. Four strategies for the manufacture of zeolite catalytic microreactors were discussed: zeolite powder coating, uniform zeolite film growth, localized zeolite growth, and etching of zeolite-silicon composite film growth inhibitors. Silicalite-1 was also prepared as free-standing membrane for zeolite membrane microseparators.

Synthesis and characterization of alumina application in support of zeolite membrane

International Nuclear Information System (INIS)

Barbosa, A.S.; Rodrigues, M.G.F.

2012-01-01

Much interest has been aroused in process applications using zeolite membrane. The physicochemical properties of the support have a strong effect on the quality of zeolite membrane. This work is to synthesize and characterize alumina for use as a support for zeolite membrane. In this work was synthesized α-alumina: 40% alumina, 0.2% for PABA, 0.5% oleic acid and 59.3% ethyl alcohol. The mixture was ground in ball mill and placed in an oven for 24 hours at 60 °C, allowed to stand for 24h. The pressing was performed with 4 tons. The pressed material was subjected to sintering at 1400 °C/hour. The samples were characterized by EDX, XRD and SEM. The results for the media by XRD showed that they are crystalline and pure. By EDX was observed that the supports consist essentially of alumina. (author)

A chemical-biological evaluation of rhodium(I) N-heterocyclic carbene complexes as prospective anticancer drugs.

Science.gov (United States)

Oehninger, Luciano; Küster, Laura Nadine; Schmidt, Claudia; Muñoz-Castro, Alvaro; Prokop, Aram; Ott, Ingo

2013-12-23

Rhodium(I) complexes bearing N-heterocyclic carbene (NHC) ligands have been widely used in catalytic chemistry, but there are very few reports of biological properties of these organometallics. A series of Rh(I)-NHC derivatives with 1,5-cyclooctadiene and CO as secondary ligands were synthesized, characterized, and biologically investigated as prospective antitumor drug candidates. Pronounced antiproliferative effects were noted for all complexes, along with moderate inhibitory activity of thioredoxin reductase (TrxR) and efficient binding to biomolecules (DNA, albumin). Biodistribution studies showed that the presence of albumin lowered the cellular uptake and confirmed the transport of rhodium into the nuclei. Changes in the mitochondrial membrane potential (MMP) were observed as well as DNA fragmentation in wild-type and daunorubicin- or vincristine-resistant Nalm-6 leukemia cells. Overall, these studies indicated that Rh(I)-NHC fragments could be used as partial structures of new antitumor agents, in particular in those drugs designed to address resistant malignant tissues. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Enhancement of ethanol oxidation at Pt and PtRu nanoparticles dispersed over hybrid zirconia-rhodium supports

Science.gov (United States)

Rutkowska, Iwona A.; Koster, Margaretta D.; Blanchard, Gary J.; Kulesza, Pawel J.

2014-12-01

A catalytic material for electrooxidation of ethanol that utilizes PtRu nanoparticles dispersed over thin films of rhodium-free and rhodium-containing zirconia (ZrO2) supports is described here. The enhancement of electrocatalytic activity (particularly in the potential range as low as 0.25-0.5 V vs. RHE), that has been achieved by dispersing PtRu nanoparticles (loading, 100 μg cm-2) over the hybrid Rh-ZrO2 support composed of nanostructured zirconia and metallic rhodium particles, is clearly evident from comparison of the respective voltammetric and chronoamperometric current densities recorded at room temperature (22 °C) in 0.5 mol dm-3 H2SO4 containing 0.5 mol dm-3 ethanol. Porous ZrO2 nanostructures, that provide a large population of hydroxyl groups in acidic medium in the vicinity of PtRu sites, are expected to facilitate the ruthenium-induced removal of passivating CO adsorbates from platinum, as is apparent from the diagnostic experiments with a small organic molecule such as methanol. Although Rh itself does not show directly any activity toward ethanol oxidation, the metal is expected to facilitate C-C bond splitting in C2H5OH. It has also been found during parallel voltammetric and chronoamperometric measurements that the hybrid Rh-ZrO2 support increases activity of the platinum component itself toward ethanol oxidation in the low potential range.

1,3-dialkyl- and 1,3-diaryl-3,4,5,6-tetrahydropyrimidin-2-ylidene rhodium(i) and palladium(II) complexes: synthesis, structure, and reactivity.

Science.gov (United States)

Mayr, Monika; Wurst, Klaus; Ongania, Karl-Hans; Buchmeiser, Michael R

2004-03-05

The synthesis of novel 1,3-diaryl- and 1,3-dialkylpyrimidin-2-ylidene-based N-heterocyclic carbenes (NHCs) and their rhodium(i) and palladium(II) complexes is described. The rhodium compounds bromo(cod)[1,3-bis(2-propyl)-3,4,5,6-tetrahydropyrimidin-2-ylidene]rhodium (7), bromo(cod)(1,3-dimesityl-3,4,5,6-tetrahydropyrimidin-2-ylidene)rhodium (8) (cod=eta(4)-1,5-cyclooctadiene, mesityl=2,4,6-trimethylphenyl), chloro(cod)(1,3-dimesityl-3,4,5,6-tetrahydropyrimidin-2-ylidene)rhodium (9), and chloro(cod)[1,3-bis(2-propyl)-3,4,5,6-tetrahydropyrimidin-2-ylidene]rhodium (10) were prepared by reaction of [[Rh(cod)Cl](2)] with lithium tert-butoxide followed by addition of 1,3-dimesityl-3,4,5,6-tetrahydropyrimidinium bromide (3), 1,3-dimesityl-3,4,5,6-tetrahydropyrimidinium tetrafluoroborate (4), 1,3-di-2-propyl-3,4,5,6-tetrahydropyrimidinium bromide (6), and 1,3-di-2-propyl-3,4,5,6-tetrahydropyrimidinium tetrafluoroborate, respectively. Complex 7 crystallizes in the monoclinic space group P2(1)/n, and 8 in the monoclinic space group P2(1). Complexes 9 and 10 were used for the synthesis of the corresponding dicarbonyl complexes dicarbonylchloro(1,3-dimesityl-3,4,5,6-tetrahydropyrimidin-2-ylidene)rhodium (11), and dicarbonylchloro[1,3-bis(2-propyl)-3,4,5,6-tetrahydropyrimidin-2-ylidene]rhodium (12). The wavenumbers nu(CO I)/nu(CO II) for 11 and 12 were used as a quantitative measure for the basicity of the NHC ligand. The values of 2062/1976 and 2063/1982 cm(-1), respectively, indicate that the new NHCs are among the most basic cyclic ligands reported so far. Compounds 3 and 6 were additionally converted to the corresponding cationic silver(i) bis-NHC complexes [Ag(1,3-dimesityl-3,4,5,6-tetrahydropyrimidin-2-ylidene)(2)]AgBr(2) (13) and [Ag[1,3-bis(2-propyl)-3,4,5,6-tetrahydropyrimidin-2-ylidene](2)]AgBr(2) (14), which were subsequently used in transmetalation reactions for the synthesis of the corresponding palladium(II) complexes Pd(1,3-dimesityl-3,4,5,6-tetrahydropyrimidin-2

Oxidation of aromatic alcohols on zeolite-encapsulated copper amino acid complexes

Energy Technology Data Exchange (ETDEWEB)

Ernst, S.; Teixeira Florencio, J.M. [Kaiserslautern Univ. (Germany). Dept. of Chemistry, Chemical Technology

1998-12-31

Copper complexes of the amino acids histidine, arginine and lysine have been introduced into the supercages of zeolite Y and, for the first time, into the large intracrystalline cavities of zeolites EMT and MCM-22. The resulting host/guest compounds are characterized by X-ray powder diffraction, UV/VIS-spectroscopy in the diffuse reflectance mode and by catalytic tests in the liquid-phase oxidation of aromatic alcohols (viz. benzyl alcohol, 2- and 3-methylbenzyl alcohol and 2,5-dimethylbenzyl alcohol) with tertiary-butylhydroperoxide as oxidant. It was observed that intracrystalline copper-amino acid complexes possess remarkable catalytic activity, yielding the corresponding aromatic aldehydes and acids. (orig.)

Adducts of nitrogenous ligands with rhodium(II) tetracarboxylates and tetraformamidinate: NMR spectroscopy and density functional theory calculations.

Science.gov (United States)

Cmoch, Piotr; Głaszczka, Rafał; Jaźwiński, Jarosław; Kamieński, Bohdan; Senkara, Elżbieta

2014-03-01

Complexation of tetrakis(μ2-N,N'-diphenylformamidinato-N,N')-di-rhodium(II) with ligands containing nitrile, isonitrile, amine, hydroxyl, sulfhydryl, isocyanate, and isothiocyanate functional groups has been studied in liquid and solid phases using (1)H, (13)C and (15)N NMR, (13)C and (15)N cross polarisation-magic angle spinning NMR, and absorption spectroscopy in the visible range. The complexation was monitored using various NMR physicochemical parameters, such as chemical shifts, longitudinal relaxation times T1 , and NOE enhancements. Rhodium(II) tetraformamidinate selectively bonded only unbranched amine (propan-1-amine), pentanenitrile, and (1-isocyanoethyl)benzene. No complexation occurred in the case of ligands having hydroxyl, sulfhydryl, isocyanate, and isothiocyanate functional groups, and more expanded amine molecules such as butan-2-amine and 1-azabicyclo[2.2.2]octane. Such features were opposite to those observed in rhodium(II) tetracarboxylates, forming adducts with all kind of ligands. Special attention was focused on the analysis of Δδ parameters, defined as a chemical shift difference between signal in adduct and corresponding signal in free ligand. In the case of (1)H NMR, Δδ values were either negative in adducts of rhodium(II) tetraformamidinate or positive in adducts of rhodium(II) tetracarboxylates. Experimental findings were supported by density functional theory molecular modelling and gauge independent atomic orbitals chemical shift calculations. The calculation of chemical shifts combined with scaling procedure allowed to reproduce qualitatively Δδ parameters. Copyright © 2013 John Wiley & Sons, Ltd.

Pentamethylcyclopentadienyl-rhodium and iridium complexes containing (N^N and N^O) bound chloroquine analogue ligands: synthesis, characterization and antimalarial properties.

Science.gov (United States)

Ekengard, Erik; Kumar, Kamlesh; Fogeron, Thibault; de Kock, Carmen; Smith, Peter J; Haukka, Matti; Monari, Magda; Nordlander, Ebbe

2016-03-07

The synthesis and characterization of twenty new pentamethylcyclopentadienyl-rhodium and iridium complexes containing N^N and N^O-chelating chloroquine analogue ligands are described. The in vitro antimalarial activity of the new ligands as well as the complexes was evaluated against the chloroquine sensitive (CQS) NF54 and the chloroquine resistant (CQR) Dd2 strains of Plasmodium falciparum. The antimalarial activity was found to be good to moderate; although all complexes are less active than artesunate, some of the ligands and complexes showed better activity than chloroquine (CQ). In particular, rhodium complexes were found to be considerably more active than iridium complexes against the CQS NF54 strain. Salicylaldimine Schiff base ligands having electron-withdrawing groups (F, Cl, Br, I and NO2) in para position of the salicyl moiety and their rhodium complexes showed good antiplasmodial activity against both the CQS-NF54 and the CQR-Dd2 strains. The crystal structures of (η(5)-pentamethylcyclopentadienyl){N(1)-(7-chloroquinolin-4-yl)-N(2)-(pyridin-2-ylmethyl)ethane-1,2-diamine)} chlororhodium(III) chloride and (η(5)-pentamethylcyclopentadienyl){(4-chloro-2-(((2-((7-chloroquinolin-4-yl)amino)ethyl)imino)methyl)phenolate)}chlororhodium(III) chloride are reported. The crystallization of the amino-pyridyl complex (η(5)-pentamethylcyclopentadienyl){(N(1)-(7-chloroquinolin-4-yl)-N(2)-(pyridin-2-ylmethyl)ethane-1,2-diamine)}chloroiridium(III) chloride in acetone resulted in the formation of the imino-pyridyl derivative (η(5)-pentamethylcyclopentadienyl){(N1-(7-chloroquinolin-4-yl)-N2-(pyridin-2-ylmethylene)ethane-1,2-diamine)}chloroiridium(III) chloride, the crystal structure of which is also reported.

Synthesis and structural studies of Cp{sup *} rhodium and Cp{sup *} iridium complexes of picolinic hydrazine ligand

Energy Technology Data Exchange (ETDEWEB)

Palepu, Narasinga Rao; Kollipara, Mohan Rao [Centre for Advanced Studies in Chemistry, North-Eastern Hill University, Shillong (India); Kaminsky Werner [Dept. of Chemistry, University of Washington, Seattle (United States)

2017-01-15

A series of Cp{sup *}Rh and Cp{sup *}Ir complexes of picolinic hydrazine ligand are synthesized and characterized. Picolinic hydrazine has yielded only dinuclear complexes in the case of rhodium metal whereas both mono and dinuclear complexes with iridium metal. Iridium complexes are formed as quaternary salts by the migration of the N–H proton onto the adjacent amine group of the hydrazine after binding to the metal. Picolinic hydrazine acts as nitrogen and oxygen donor ligand in the form of bi and tetradentate bonding modes.

Enhanced photocatalytic activity of supported TiO{sub 2} by selective surface modification of zeolite Y

Energy Technology Data Exchange (ETDEWEB)

Guesh, Kiros [Chemistry-Department, Addis Ababa University, P.O. Box 1176, Addis Ababa (Ethiopia); Mizan-Tepi University, P.O. Box 260, Mizan-Teferi (Ethiopia); Márquez-Álvarez, Carlos [Instituto de Catálisis y Petroleoquímica, CSIC, c/Marie Curie 2, 28049 Madrid (Spain); Chebude, Yonas [Chemistry-Department, Addis Ababa University, P.O. Box 1176, Addis Ababa (Ethiopia); Díaz, Isabel, E-mail: idiaz@icp.csic.es [Chemistry-Department, Addis Ababa University, P.O. Box 1176, Addis Ababa (Ethiopia); Instituto de Catálisis y Petroleoquímica, CSIC, c/Marie Curie 2, 28049 Madrid (Spain)

2016-08-15

Highlights: • XPS analysis confirmed that 50% of the Al was removed from the surface of zeolite Y. • Loaded TiO{sub 2} on the treated zeolites showed 12 times higher TORm than the parent zeolite. • Supported TiO{sub 2} showed very low leaching of TiO{sub 2} nanoparticles than non supported. - Abstract: Zeolite Y was treated using ammonium acetate and ammonium fluoride sequentially. As a consequence the aluminum from the surface was selectively removed. Then, loading with TiO{sub 2} (20 wt%) led to a final photocatalyst. The samples were characterized by X-ray diffraction (XRD), elemental analysis (ICP-OES), N{sub 2} adsorption, diffuse reflectance UV–vis spectroscopy (DRS), photoluminescence spectroscopy (PL), and X-ray photoelectron spectroscopy (XPS). It was found that 50% of the Al atoms were removed from the surface of the zeolite without affecting the framework structure. The TiO{sub 2}/treated zeolite sample yielded 92% photocatalytic degradation of 10 ppm methyl orange (MO), a model pollutant, while the TiO{sub 2}/parent zeolite converted only 7.6%. The mass normalized turnover rate (TOR{sub m}) of the treated zeolite loaded with TiO{sub 2} was about 12 times higher than that of the parent zeolite loaded with the same amount of TiO{sub 2} precursor. This higher photocatalytic activity of the TiO{sub 2} supported on treated zeolite can be attributed to a more efficient interaction of the TiO{sub 2} with the zeolite leading to higher adsorption capacity. Reusability of the photocatalysts was assessed by performing three consecutive reaction cycles that showed no significant loss of photocatalytic activity.

Impact of zeolite-Y framework on the geometry and reactivity of Ru (III) benzimidazole complexes - A DFT study

Science.gov (United States)

Selvaraj, Tamilmani; Rajalingam, Renganathan; Balasubramanian, Viswanathan

2018-03-01

A detailed comparative Density Functional Theory (DFT) study is made to understand the structural changes of the guest complex due to steric and electronic interactions with the host framework. In this study, Ru(III) benzimidazole and 2- ethyl Ru(III) benzimidazole complexes encapsulated in a supercage of zeolite Y. The zeolitic framework integrity is not disturbed by the intrusion of the large guest complex. A blue shift in the d-d transition observed in the UV-Visible spectroscopic studies of the zeolite encapsulated complexes and they shows a higher catalytic efficiency. Encapsulation of zeolite matrix makes the metal center more viable to nucleophilic attack and favors the phenol oxidation reaction. Based on the theoretical calculations, transition states and structures of reaction intermediates involved in the catalytic cycles are derived.

Chemical Posttranslational Modification with Designed Rhodium(II) Catalysts.

Science.gov (United States)

Martin, S C; Minus, M B; Ball, Z T

2016-01-01

Natural enzymes use molecular recognition to perform exquisitely selective transformations on nucleic acids, proteins, and natural products. Rhodium(II) catalysts mimic this selectivity, using molecular recognition to allow selective modification of proteins with a variety of functionalized diazo reagents. The rhodium catalysts and the diazo reactivity have been successfully applied to a variety of protein folds, the chemistry succeeds in complex environments such as cell lysate, and a simple protein blot method accurately assesses modification efficiency. The studies with rhodium catalysts provide a new tool to study and probe protein-binding events, as well as a new synthetic approach to protein conjugates for medical, biochemical, or materials applications. © 2016 Elsevier Inc. All rights reserved.

Oxidative Olefination of Anilides with Unactivated Alkenes Catalyzed by an (Electron-Deficient η(5) -Cyclopentadienyl)Rhodium(III) Complex Under Ambient Conditions.

Science.gov (United States)

Takahama, Yuji; Shibata, Yu; Tanaka, Ken

2015-06-15

The oxidative olefination of sp(2) C-H bonds of anilides with both activated and unactivated alkenes using an (electron-deficient η(5) -cyclopentadienyl)rhodium(III) complex is reported. In contrast to reactions using this electron-deficient rhodium(III) catalyst, [Cp*RhCl2 ]2 showed no activity against olefination with unactivated alkenes. In addition, the deuterium kinetic isotope effect (DKIE) study revealed that the C-H bond cleavage step is thought to be the turnover-limiting step. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis and structures of a pincer-type rhodium(iii) complex: reactivity toward biomolecules.

Science.gov (United States)

Milutinović, Milan M; Bogojeski, Jovana V; Klisurić, Olivera; Scheurer, Andreas; Elmroth, Sofi K C; Bugarčić, Živadin D

2016-10-04

A novel rhodium(iii) complex [Rh III (H 2 L tBu )Cl 3 ] (1) (H 2 L tBu = 2,6-bis(5-tert-butyl-1H-pyrazol-3-yl)pyridine) containing a pincer type, tridentate nitrogen-donor chelate system was synthesized. Single crystal X-ray structure analysis revealed that 1 crystallizes in the orthorhombic space group Pbcn with a = 20.7982(6), b = 10.8952(4), c = 10.9832(4) Å, V = 2488.80(15) Å 3 , and eight molecules in the unit cell. The rhodium center in the complex [Rh III (H 2 L tBu )Cl 3 ] (1) is coordinated in a slightly distorted octahedral geometry by the tridentate N,N,N-donor and three chloro ligands, adopting a mer arrangement with an essentially planar ligand skeleton. Due to the tridentate coordination of the N,N,N-donor, the central nitrogen atom N1 is located closer to the Rh III center. The reactivity of the synthesized complex toward small biomolecules (l-methionine (l-Met), guanosine-5'-monophosphate (5'-GMP), l-histidine (l-His) and glutathione (GSH)) and to a series of duplex DNAs and RNA was investigated. The order of reactivity of the studied small biomolecules is: 5'-GMP > GSH > l-Met > l-His. Duplex RNA reacts faster with the [Rh III (H 2 L tBu )Cl 3 ] complex than duplex DNA, while shorter duplex DNA (15mer GG) reacts faster compared with 22mer GG duplex DNA. In addition, a higher reactivity is achieved with a DNA duplex with a centrally located GG-sequence than with a 22GTG duplex DNA, in which the GG-sequence is separated by a T base. Furthermore, the interaction of this metal complex 1 with calf thymus DNA (CT-DNA) and bovine serum albumin (BSA) was examined by absorption (UV-Vis) and emission spectral studies (EthBr displacement studies). Overall, the studied complex exhibited good DNA and BSA interaction ability.

Atmosphere-Controlled Chemoselectivity: Rhodium-Catalyzed Alkylation and Olefination of Alkylnitriles with Alcohols.

Science.gov (United States)

Li, Junjun; Liu, Yuxuan; Tang, Weijun; Xue, Dong; Li, Chaoqun; Xiao, Jianliang; Wang, Chao

2017-10-17

The chemoselective alkylation and olefination of alkylnitriles with alcohols have been developed by simply controlling the reaction atmosphere. A binuclear rhodium complex catalyzes the alkylation reaction under argon through a hydrogen-borrowing pathway and the olefination reaction under oxygen through aerobic dehydrogenation. Broad substrate scope is demonstrated, permitting the synthesis of some important organic building blocks. Mechanistic studies suggest that the alkylation product may be formed through conjugate reduction of an alkene intermediate by a rhodium hydride, whereas the formation of olefin product may be due to the oxidation of the rhodium hydride complex with molecular oxygen. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rhodium Phosphine-π-Arene Intermediates in the Hydroamination of Alkenes

Science.gov (United States)

Liu, Zhijian; Yamamichi, Hideaki; Madrahimov, Sherzod T.; Hartwig, John F.

2011-01-01

A detailed mechanistic study of the intramolecular hydroamination of alkenes with amines catalyzed by rhodium complexes of a biaryldialkylphosphine are reported. The active catalyst is shown to contain the phosphine ligand bound in a κ1, η6 form in which the arene is π-bound to rhodium. Addition of deuterated amine to an internal olefin showed that the reaction occurs by trans addition of the N-H bond across the C=C bond, and this stereochemistry implies that the reaction occurs by nucleophilic attack of the amine on a coordinated alkene. Indeed, the cationic rhodium fragment binds the alkene over the secondary amine, and the olefin complex was shown to be the catalyst resting state. The reaction was zero-order in substrate, when the concentration of olefin was high, and a primary isotope effect was observed. The primary isotope effect, in combination with the observation of the alkene complex as the resting state, implies that nucleophilic attack of the amine on the alkene is reversible and is followed by turnover-limiting protonation. This mechanism constitutes an unusual pathway for rhodium-catalyzed additions to alkenes and is more closely related to the mechanism for palladium-catalyzed addition of amide N-H bonds to alkenes. PMID:21309512

Vanadia supported on zeolites for SCR of NO by ammonia

DEFF Research Database (Denmark)

Putluru, Siva Sankar Reddy; Riisager, Anders; Fehrmann, Rasmus

2010-01-01

, acidity and micropore structure of the support. Apparently the support hosted the potassium oxide on the acid sites, thereby protecting the active vanadium species from poisoning. Zeolite based catalysts might therefore prove useful for SCR of NO in alkali-containing flue gases from, e.g. biomass fired...

Moessbauer spectroscopic characterisation of catalysts obtained by interaction between tetra-n-butyl-tin and silica or silica supported rhodium

International Nuclear Information System (INIS)

Millet, J.M.M.; Toyir, J.; Didillon, B.; Candy, J.P.; Nedez, C.; Basset, J.M.

1997-01-01

Moessbauer spectroscopy at 78 K was used to study the interaction between tetra-n-butyl-tin and the surfaces of silica or silica supported rhodium. At room temperature, the tetra-n-butyl-tin was physically adsorbed on the surfaces. After reaction under hydrogen at 373 K, the formation of grafted organometallic fragments on the Rh surface was confirmed whereas with pure silica, ≡SiO-Sn(n-C 4 H 9 ) 3 moieties were observed. After treatment at 523 K, the rhodium grafted organometallic species was completely decomposed and there was formation of a defined bimetallic RhSn compound

Antitumor effect and toxicity of free rhodium (II) citrate and rhodium (II) citrate-loaded maghemite nanoparticles in mice bearing breast cancer.

Science.gov (United States)

Carneiro, Marcella Lemos Brettas; Peixoto, Raphael C A; Joanitti, Graziela A; Oliveira, Ricardo G S; Telles, Luis A M; Miranda-Vilela, Ana L; Bocca, Anamélia L; Vianna, Leonora M S; da Silva, Izabel C R; de Souza, Aparecido R; Lacava, Zulmira G M; Báo, Sônia N

2013-02-16

Magnetic fluids containing superparamagnetic iron oxide nanoparticles represent an attractive platform as nanocarriers in chemotherapy. Recently, we developed a formulation of maghemite nanoparticles coated with rhodium (II) citrate, which resulted in in vitro cytotoxicity enhanced up to 4.6 times when compared to free rhodium (II) citrate formulation on breast carcinoma cells. In this work, we evaluate the antitumor activity and toxicity induced by these formulations in Balb/c mice bearing orthotopic 4T1 breast carcinoma. Mice were evaluated with regard to the treatments' toxicity through analyses of hemogram, serum levels of alanine aminotransferase, iron, and creatinine; DNA fragmentation and cell cycle of bone marrow cells; and liver, kidney and lung histology. In addition, the antitumor activity of rhodium (II) citrate and maghemite nanoparticles coated with rhodium (II) citrate was verified by tumor volume reduction, histology and immunohistochemistry. Regarding the treatments' toxicity, no experimental groups had alterations in levels of serum ALT or creatinine, and this suggestion was corroborated by the histopathologic examination of liver and kidney of mice. Moreover, DNA fragmentation frequency of bone marrow cells was lower than 15% in all experimental groups. On the other hand, the complexes rhodium (II) citrate-functionalized maghemite and free rhodium (II) citrate led to a marked growth inhibition of tumor and decrease in CD31 and Ki-67 staining. In summary, we demonstrated that both rhodium (II) citrate and maghemite nanoparticles coated with rhodium (II) citrate formulations exhibited antitumor effects against 4T1 metastatic breast cancer cell line following intratumoral administration. This antitumor effect was followed by inhibition of both cell proliferation and microvascularization and by tumor tissue injury characterized as necrosis and fibrosis. Remarkably, this is the first published report demonstrating the therapeutic efficacy of maghemite

Rhodium-Catalyzed Decarbonylation of Aldoses

DEFF Research Database (Denmark)

Monrad, Rune; Madsen, Robert

2007-01-01

A catalytic procedure is described for decarbonylation of unprotected aldoses to afford alditols with one less carbon atom. The reaction is performed with the rhodium complex Rh(dppp)2Cl in a refluxing diglyme - DMA solution. A slightly improved catalyst turnover is observed when a catalytic amount...

Mono and dinuclear iridium, rhodium and ruthenium complexes containing chelating carboxylato pyrazine ligands: Synthesis, molecular structure and electrochemistry

Czech Academy of Sciences Publication Activity Database

Govindaswamy, P.; Therrien, B.; Süss-Fink, G.; Štěpnička, P.; Ludvík, Jiří

2007-01-01

Roč. 692, č. 8 (2007), s. 1661-1671 ISSN 0022-328X R&D Projects: GA MŠk LC510; GA MŠk(CZ) LC06070 Institutional research plan: CEZ:AV0Z40400503 Keywords : dinuclear complexes * iridium * rhodium * ruthenium * electrochemistry Subject RIV: CG - Electrochemistry Impact factor: 2.168, year: 2007

Coupling of Electron Transfer and Bond Dissociation Processes in Dinuclear Complexes with Rhodium and Iridium Reaction Centers Bridged by 2,2'-Bipyrimidine

Czech Academy of Sciences Publication Activity Database

Kaim, W.; Reinhardt, R.; Greulich, S.; Sieger, M.; Klein, A.; Fiedler, Jan

2001-01-01

Roč. 66, č. 2 (2001), s. 291-306 ISSN 0010-0765 R&D Projects: GA MŠk OC D15.10 Institutional research plan: CEZ:AV0Z4040901 Keywords : EPR spectroscopy * iridium complexes * rhodium complexes Subject RIV: CG - Electrochemistry Impact factor: 0.778, year: 2001

The isomerization of allylrhodium intermediates in the rhodium-catalyzed nucleophilic allylation of cyclic imines.

Science.gov (United States)

Hepburn, Hamish B; Lam, Hon Wai

2014-10-20

Allylrhodium species generated from potassium allyltrifluoroborates can undergo isomerization by 1,4-rhodium(I) migration to give more complex isomers, which then react with cyclic imines to provide products with up to three new stereochemical elements. High enantioselectivities are obtained using chiral diene-rhodium complexes. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Platinum, palladium, and rhodium analyses of ultramafic and mafic rocks from the Stillwater Complex, Montana

Science.gov (United States)

Page, Norman J; Riley, Leonard Benjamin; Haffty, Joseph

1969-01-01

Analyses by a combination fire- assay-solution-optical-emission spectrographic method of 137 rocks from the Stillwater Complex, Mont., indicate that platinum, palladium, and rhodium are preferentially concentrated in chromitite zones. The A chromitite zone (21 samples) has an average of 988.9 ppb (pans per billion, 10-9) Pt, 2290.2 ppb Pd, and 245.9 ppb Rh and reaches a maximum (to date) of 8,000 ppb Pt, 11,000 ppb Pd, and 1,700 ppb Rh.

DNA Mismatch Binding and Antiproliferative Activity of Rhodium Metalloinsertors

Science.gov (United States)

Ernst, Russell J.; Song, Hang; Barton, Jacqueline K.

2009-01-01

Deficiencies in mismatch repair (MMR) are associated with carcinogenesis. Rhodium metalloinsertors bind to DNA base mismatches with high specificity and inhibit cellular proliferation preferentially in MMR-deficient cells versus MMR-proficient cells. A family of chrysenequinone diimine complexes of rhodium with varying ancillary ligands that serve as DNA metalloinsertors has been synthesized, and both DNA mismatch binding affinities and antiproliferative activities against the human colorectal carcinoma cell lines HCT116N and HCT116O, an isogenic model system for MMR deficiency, have been determined. DNA photocleavage experiments reveal that all complexes bind to the mismatch sites with high specificities; DNA binding affinities to oligonucleotides containing single base CA and CC mismatches, obtained through photocleavage titration or competition, vary from 104 to 108 M−1 for the series of complexes. Significantly, binding affinities are found to be inversely related to ancillary ligand size and directly related to differential inhibition of the HCT116 cell lines. The observed trend in binding affinity is consistent with the metalloinsertion mode where the complex binds from the minor groove with ejection of mismatched base pairs. The correlation between binding affinity and targeting of the MMR-deficient cell line suggests that rhodium metalloinsertors exert their selective biological effects on MMR-deficient cells through mismatch binding in vivo. PMID:19175313

Preparation of Rhodium(III) complexes with 2(1H)-quinolinone derivatives and evaluation of their in vitro and in vivo antitumor activity.

Science.gov (United States)

Lu, Xing; Wu, Yi-Ming; Yang, Jing-Mei; Ma, Feng-E; Li, Liang-Ping; Chen, Sheng; Zhang, Ye; Ni, Qing-Ling; Pan, Ying-Ming; Hong, Xue; Peng, Yan

2018-05-10

A series of 2(1H)-quinolinone derivatives and their rhodium (III) complexes were designed and synthesized. All the rhodium (III) complexes exhibited higher in vitro cytotoxicity for Hep G2, HeLa 229, MGC80-3, and NCI-H460 human tumor cell lines than their ligands and cisplatin, and among them complex 9 was found to be selectively cytotoxic to tumor cells. Further investigation revealed that complex 9 caused cell cycle arrest at the G2/M phase and induced apoptosis, and inhibited the proliferation of Hep G2 cells by impeding the phosphorylation of epidermal growth factor receptor (EGFR) and its downstream enzymes. Complex 9 also up-regulated the proapoptotic proteins Bak, Bax, and Bim, which altogether activated caspase-3/9 to initiate cell apoptosis. Notably, complex 9 effectively inhibited tumor growth in the NCI-H460 xenograft mouse model with less adverse effect than cisplatin. Copyright © 2018 Elsevier Masson SAS. All rights reserved.

Bibliographies on radiation chemistry. 9. Metal ions and complexes. Part A: Cobalt, rhodium, iridium

Energy Technology Data Exchange (ETDEWEB)

Hoffman, M Z; Ross, A B

1986-01-01

The one-electron oxidation and reduction of metal ions and complexes can yield species in unusual oxidation states, and ligand-radicals coordinated to the central metal. These often unstable species can be mechanistically important intermediates in thermal, photochemical, and electrochemical reactions involving metal-containing substances. Their generation via radiolysis provides an alternate means of characterizing them using kinetic and spectroscopic techniques. We hope these bibliographies on the radiation chemistry of metal ions and complexes, presented according to periodic groups, will prove useful to researchers in metallo-redox chemistry. These bibliographies contain only primary literature sources; reviews are not included. However, a list of general review articles on the radiation chemistry of metal ions and complexes is presented here in the first section which covers cobalt, rhodium and iridium, Group 9 in the new IUPAC notation. Additional parts of the bibliography are planned, covering other periodic groups. Part A of the bibliography was prepared by a search of the Radiation Chemistry Data Center Bibliographic Data Base (RCDCbib) through January 1986 for papers on rhodium, iridium and cobalt compounds, and radiolysis (both continuous and pulsed). Papers in which the use of metal compounds was incidental to the primary objective of the study were excluded. Excluded also were publications in unrefereed and obscure sources such as meeting proceedings, internal reports, dissertations, and patents. The majority of the studies in the resultant compilation deal with experiments performed on solutions, mainly aqueous, although a substantial fraction is devoted to solid-state esr measurements. The references are listed in separate sections for each of the metals, and are presented in approximate chronological order.

Zeolite function studied by neutron diffraction

International Nuclear Information System (INIS)

Newsam, J.M.

1988-01-01

Some recent figures relating to industrial uses of zeolites are summarized. Recent advances in the application of neutron diffraction to zeolite science are overviewed, with particular emphasis on powder diffraction (PND) results. Single crystal neutron diffraction studies of some 17 hydrated natural and synthetic zeolites have now appeared and they provide a consistent picture of zeolite-water interactions. Complete PND studies of hydrated synthetic ABW- and SOD-framework zeolites have also been reported. Other PND studies have explored the structural consequences of non-framework cation exchange, of framework modification by dealumination, and of framework cation substitution. Relatively simple zeolite-hydrocarbon sorbate complexes that have been studied include benzene in zeolite Y, and benzene and pyridine in zeolite L. Areas that are well poised for further development include further extensions to lower symmetry systems, the use of PND data for zeolite structure solution, studies at elevated temperatures and pressures, and further studies of zeolite sorbate complexes. (author) 68 refs., 7 figs

Line profile analyses of rhodium metal obtained by decomposition of rhodium carbonyl

International Nuclear Information System (INIS)

Chandra, D.; Mandalia, H.; Garner, M.L.; Blakely, M.K.; Lau, K.H.

1995-01-01

Metal carbonyls are important for chemical vapor deposition (CVD) of metals and alloys and formation of high surface area metallic particles which have potential applications as catalysts. Rhodium carbonyl [Rh 6 (CO) 16 ] produces high surface area metallic particles whose structure has been reported as monoclinic (I2/a) with lattice dimensions, a=17.00(±0.03)Angstrom, b=9.78(±0.02)Angstrom, c=17.53(±0.03)Angstrom and Β=121 degrees 45' ± 30' at room temperature. Generally, metal carbonyl crystals dissociate under vacuum as carbonyl gas and decompose to metallic crystals and carbon monoxide at higher temperatures. However, the behavior of rhodium carbonyl crystals is different; they decompose directly to metallic rhodium without the formation of rhodium carbonyl gas in vacuum. Several residual fine grains of rhodium metal are found after the decomposition in vacuum at relatively low temperatures. The metallic samples of rhodium were obtained from vapor pressure experiments using torsion Knudsen-effusion apparatus. X-ray diffraction analyses performed on these gains showed severely broadened Bragg reflections indicative of small particle size and/or lattice microgram. In this study, a comparison of lattice strains and domain sizes obtained by integral breadth and Fourier methods has been made. In addition a comparison of the lattice strains and domain sizes has been made between the Cauchy, Gaussian, Cauchy-Gaussian and Aqua integral breadth methods

Investigation into cathode polarization during deposition of rhodium-nickel and rhodium-indium alloys

International Nuclear Information System (INIS)

Evdokimova, N.V.; Byacheslavov, P.M.; Lokshtanova, O.G.

1979-01-01

The results of kinetic regularities experimental investigations during electrodeposition of rhodium-nickel and rhonium-indium alloys are presented. Methods of general and partial polarization curves have been used to show the nature of polarization during the rhonium-nickel and rhodium-indium alloys deposition. It is shown that indium into the rhodium-indium alloy and nickel into the rhodium-nickel alloy deposit with great depolarization ( PHIsub(In)sup(0)=-0.33B, PHIsub(Ni)sup(0)=-0.23B). Indium and nickel in pure form do not deposit from the electrolytes of the given composition (H 2 SO 4 - 50 g/l, HNH 2 SO 3 -10 g/l). The recalculation of partial polarization curve of indium precipitation into the rhodium-indium alloy in the mixed kinetics coordinates gives a straight line with 40 mV inclination angle. This corresponds to the delayed stage of the second electron addition with the imposition of diffusion limitations

Detergent zeolite complex "Ceosil", Tallinn, Estonia

OpenAIRE

Stanković Mirjana S.; Pezo Lato L.

2003-01-01

The IGPC Engineering Department, together with the "Birac", Zvornik Engineering Department designed basic projects for detergent zeolite production, using waste flotation sand and hydrates. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, production plant in Tallinn, Estonia was constructed, with a capacity of 100,000 t/y from 1989. to 1993. This plant became the biggest producer of detergent zeolite in the world.Several goals we...

Rhodium. Suppl. Vol. B1

International Nuclear Information System (INIS)

Griffith, W.P.; Jehn, H.; McCleverty, J.A.; Raub, C.J.; Robinson, S.D.

1982-01-01

The present rhodium vol. B1 is concerned largely with linary compounds and coordination complexes of this important metal, which is used either alone or in alloy form for fabrication of other materials or for heterogeneous catalysis. In first two chapters are devoted for hydrides, oxides, ternary and quaternary oxorhodates. Third chapter is on different type of complexes with nitrogen. From chapter four to seven is on halogen complexes with this metal. Next chapters are on sulphides, sulphoxide and sulphito complexes, sulphates and sulphato complexes, selenides and tellurides, borides, borane complexes, carbides, carbonato, cyno, fulminato and thiocyanato complexes. Finally, silicide, phosphides, phosphito and arsenides are treated over here. (AB)

Determination of rhodium in metallic alloy and water samples using cloud point extraction coupled with spectrophotometric technique

Science.gov (United States)

Kassem, Mohammed A.; Amin, Alaa S.

2015-02-01

A new method to estimate rhodium in different samples at trace levels had been developed. Rhodium was complexed with 5-(4‧-nitro-2‧,6‧-dichlorophenylazo)-6-hydroxypyrimidine-2,4-dione (NDPHPD) as a complexing agent in an aqueous medium and concentrated by using Triton X-114 as a surfactant. The investigated rhodium complex was preconcentrated with cloud point extraction process using the nonionic surfactant Triton X-114 to extract rhodium complex from aqueous solutions at pH 4.75. After the phase separation at 50 °C, the surfactant-rich phase was heated again at 100 °C to remove water after decantation and the remaining phase was dissolved using 0.5 mL of acetonitrile. Under optimum conditions, the calibration curve was linear for the concentration range of 0.5-75 ng mL-1 and the detection limit was 0.15 ng mL-1 of the original solution. The enhancement factor of 500 was achieved for 250 mL samples containing the analyte and relative standard deviations were ⩽1.50%. The method was found to be highly selective, fairly sensitive, simple, rapid and economical and safely applied for rhodium determination in different complex materials such as synthetic mixture of alloys and environmental water samples.

Block copolymer lithography of rhodium nanoparticles for high temperature electrocatalysis.

Science.gov (United States)

Boyd, David A; Hao, Yong; Li, Changyi; Goodwin, David G; Haile, Sossina M

2013-06-25

We present a method for forming ordered rhodium nanostructures on a solid support. The approach makes use of a block copolymer to create and assemble rhodium chloride nanoparticles from solution onto a surface; subsequent plasma and thermal processing are employed to remove the polymer and fully convert the nanostructures to metallic rhodium. Films cast from a solution of the triblock copolymer poly(styrene-b-2-vinyl pyridine-b-ethylene oxide) dissolved in toluene with rhodium(III) chloride hydrate were capable of producing a monolayer of rhodium nanoparticles of uniform size and interparticle spacing. The nanostructures were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, and atomic force microscopy. The electrocatalytic performance of the nanoparticles was investigated with AC impedance spectroscopy. We observed that the addition of the particles to a model solid oxide fuel cell anode provided up to a 14-fold improvement in the anode activity as evidenced by a decrease in the AC impedance resistance. Examination of the anode after electrochemical measurement revealed that the basic morphology and distribution of the particles were preserved.

Energetic driving force of H spillover between rhodium and titania surfaces : a DFT view

NARCIS (Netherlands)

Conradie, J.; Gracia, J.; Niemantsverdriet, J.W.

2012-01-01

Hydrogen spillover from a rhodium particle, over the most stable (111) surface, to a TiO2 rutile support occurs at low hydrogen coverage because the adsorption energy of H atoms at low hydrogen coverage on rutile is larger than that on rhodium. H diffuses over the support with an activation barrier

Hierarchical zeolites: progress on synthesis and characterization of mesoporous zeolite single crystal catalysts

DEFF Research Database (Denmark)

Kustova, Marina; Egeblad, Kresten; Christensen, Claus H.

2007-01-01

Recently, a new family of crystalline zeolitic materials was reported, the so-called mesoporous zeolite single crystals featuring individual zeolite single crystals with an additional noncrystalline mesopore system interconnected with the usual micropore system of the zeolite, resulting...... measurements. Additionally, the results of diffusion of n-hexadecane in conventional and mesoporous zeolites are presented. Isomerization and cracking of n-hexadecane was chosen as model test reaction for these materials. All results support that mesoporous zeolites are superior catalysts due to improved mass...... transport. Importantly, the mesoporous zeolites show significant improved resistance to poisoning by carbon formation....

Versatile deprotonated NHC: C,N-bridged dinuclear iridium and rhodium complexes

Directory of Open Access Journals (Sweden)

Albert Poater

2016-01-01

Full Text Available Bearing the versatility of N-heterocyclic carbene (NHC ligands, here density functional theory (DFT calculations unravel the capacity of coordination of a deprotonated NHC ligand (pNHC to generate a doubly C2,N3-bridged dinuclear complex. Here, in particular the discussion is based on the combination of the deprotonated 1-arylimidazol (aryl = mesityl (Mes with [M(cod(μ-Cl] (M = Ir, Rh generated two geometrical isomers of complex [M(cod{µ-C3H2N2(Mes-κC2,κN3}]2. The latter two isomers display conformations head-to-head (H-H and head-to-tail (H-T of CS and C2 symmetry, respectively. The isomerization from the H-H to the H-T conformation is feasible, whereas next substitutions of the cod ligand by CO first, and PMe3 later confirm the H-T coordination as the thermodynamically preferred. It is envisaged the exchange of the metal, from iridium to rhodium, confirming here the innocence of the nature of the metal for such arrangements of the bridging ligands.

Hydrodeoxygenation of Methyl Laurate over Ni Catalysts Supported on Hierarchical HZSM-5 Zeolite

Directory of Open Access Journals (Sweden)

Nana Li

2017-12-01

Full Text Available The hierarchical HZSM-5 zeolite was prepared successfully by a simple NaOH treatment method. The concentration of NaOH solution was carefully tuned to optimal the zeolite acidity and pore structure. Under NaOH treatment conditions, a large number of mesopores, which interconnected with the retained micropores, were created to facilitate mass transfer performance. There are very good correlations between the decline of the relative zeolite crystallinity and the loss of micropores volume. The Ni nanoclusters were uniformly confined in the mesopores of hierarchical HZSM-5 by the excessive impregnation method. The direct deoxygenation in N2 and hydrodeoxygenation in H2 of the methyl laurate were compared respectively over the Ni/HZSM-5 catalysts. In the N2 atmosphere, the deoxygenation rate of the methyl laurate on the Ni/HZSM-5 catalyst is relatively slow. In the presence of H2, the synergistic effect between the hydrogenation function of the metal and the acid function of the zeolite supports can make the deoxygenation level more obvious. The yield of hydrocarbon products gradually reached the maximum with the appropriate treatment concentration of 1M NaOH, which could be attributed to the improved mass transfer in the hierarchical HZSM-5 supports.

Investigation of Gasochromic Rhodium Complexes Towards Their Reactivity to CO and Integration into an Optical Gas Sensor for Fire Gas Detection

Directory of Open Access Journals (Sweden)

Carolin Pannek

2018-06-01

Full Text Available The detection of the toxic gas carbon monoxide (CO in the low ppm range is required in different applications. We present a study of the reactivity of different gasochromic rhodium complexes towards the toxic gas carbon monoxide (CO. Therefore, variations of binuclear rhodium complexes with different ligands were prepared. They were characterized by FTIR spectroscopy, 1H NMR spectroscopy, and differential scanning calorimetry. All complexes are spectroscopically distinguishable and temperature stable up to at least 187 °C. The gasochromic behavior of all different compounds was tested. Therefore, the compounds were dissolved in toluene and exposed to 100 ppm CO for 10 min to investigate their gas sensitivity and reaction velocity. The changes in the transmission spectra were recorded by UV/vis spectroscopy. Furthermore, a significant influence of the solvent to the color dyes’ gasochromic reaction and behavior was observed. After characterization, one complex was transferred as sensing element into an optical gas sensor. Two different measurement principles (reflection- and waveguide-based were built up and tested towards their capability as gasochromic CO sensors. Finally, different gas-dependent measurements were carried out.

Organometallic rhodium(III) and iridium(III) cyclopentadienyl complexes with curcumin and bisdemethoxycurcumin co-ligands.

Science.gov (United States)

Pettinari, Riccardo; Marchetti, Fabio; Pettinari, Claudio; Condello, Francesca; Petrini, Agnese; Scopelliti, Rosario; Riedel, Tina; Dyson, Paul J

2015-12-21

A series of half-sandwich cyclopentadienyl rhodium(III) and iridium(III) complexes of the type [Cp*M(curc/bdcurc)Cl] and [Cp*M(curc/bdcurc)(PTA)][SO3CF3], in which Cp* = pentamethylcyclopentadienyl, curcH = curcumin and bdcurcH = bisdemethoxycurcumin as O^O-chelating ligands, and PTA = 1,3,5-triaza-7-phosphaadamantane, is described. The X-ray crystal structures of three of the complexes, i.e. [Cp*Rh(curc)(PTA)][SO3CF3] (5), [Cp*Rh(bdcurc)(PTA)][SO3CF3] (6) and [Cp*Ir(bdcurc)(PTA)][SO3CF3] (8), confirm the expected "piano-stool" geometry. With the exception of 5, the complexes are stable under pseudo-physiological conditions and are moderately cytotoxic to human ovarian carcinoma (A2780 and A2780cisR) cells and also to non-tumorigenic human embryonic kidney (HEK293) cells, but lack the cancer cell selectivity observed for related arene ruthenium(II) complexes.

Selective Ring Opening of 1-Methylnaphthalene Over NiW-Supported Catalyst Using Dealuminated Beta Zeolite.

Science.gov (United States)

Kim, Eun-Sang; Lee, You-Jin; Kim, Jeong-Rang; Kim, Joo-Wan; Kim, Tae-Wan; Chae, Ho-Jeong; Kim, Chul-Ung; Lee, Chang-Ha; Jeong, Soon-Yong

2016-02-01

Nanoporous Beta zeolite was dealuminated by weak acid treatment for reducing the acidity. Bi-functional catalysts were prepared using commercial Beta zeolites and the dealuminated zeolites for acidic function, NiW for metallic function. 1-Methylnaphthalene was selected as a model compound for multi-ring aromatics in heavy oil, and its selective ring opening reaction has been investigated using the prepared bi-functional catalysts with different acidity in fixed bed reaction system. The dealuminated Beta zeolites, which crystal structure and nanoporosity were maintained, showed the higher SiO2/Al2O3 ratio and smaller acidity than their original zeolite. NiW-supported catalyst using the dealuminated Beta zeolite with SiO2/Al203 mole ratio of 55 showed the highest performance for the selective ring opening. The acidity of catalyst seemed to play an important role as active sites for the selective ring opening of 1-methylnaphthalene but there should be some optimum catalyst acidity for the reaction. The acidity of Beta zeolite could be controlled by the acid treatment and the catalyst with the optimum acidity for the selective ring opening could be prepared.

Mixed N-Heterocyclic Carbene-Bis(oxazolinyl)borato Rhodium and Iridium Complexes in Photochemical and Thermal Oxidative Addition Reactions

Energy Technology Data Exchange (ETDEWEB)

Xu, Songchen [Ames Laboratory; Manna, Kuntal [Ames Laboratory; Ellern, Arkady [Ames Laboratory; Sadow, Aaron D [Ames Laboratory

2014-12-08

-[Ir](H)(Ph) complex. Alternatively, the rhodium carbonyl 5 or iridium isocyanide {PhB(OxMe2)2ImMes}Ir(CO)CNtBu (15) reacts with PhSiH3 in the dark to form the silyl compound {PhB(OxMe2)2ImMes}RhH(SiH2Ph)CO (14) or {PhB(OxMe2)2ImMes}IrH(SiH2Ph)CNtBu (17). These examples demonstrate the enhanced thermal reactivity of {PhB(OxMe2)2ImMes}-supported iridium and rhodium carbonyl compounds in comparison to tris(oxazolinyl)borate, tris(pyrazolyl)borate, and cyclopentadienyl-supported compounds.

Polypropylene obtained through zeolite supported catalysts

Directory of Open Access Journals (Sweden)

Queli C. Bastos

2004-01-01

Full Text Available Propylene polymerizations were carried out with f2C(Flu(CpZrCl2 and SiMe2(Ind2ZrCl2 catalysts supported on silica, zeolite sodic mordenite (NaM and acid mordenite (HM. The polymerizations were performed at different temperatures and varying aluminium/zirconium molar ratios ([Al]/[Zr]. The effect of these reaction parameters on the catalyst activity was investigated using a proposed statistical experimental planning. In the case of f2C(Flu(CpZrCl2, SiO2 and NaM were used as support and the catalyst performance evaluated using toluene and pentane as polymerization solvent. The molecular weight, molecular weight distribution, melting point and crystallinity of the polymers were examined. The results indicate very high activities for the syndiospecific heterogeneous system. Also, the polymers obtained had superior Mw and stereoregularity.

Polypropylene obtained through zeolite supported catalysts

International Nuclear Information System (INIS)

Bastos, Queli C.; Marques, Maria de Fatima V.

2004-01-01

Propylene polymerizations were carried out with φ 2 C(Flu)(Cp)ZrCl 2 and SiMe 2 (Ind)2ZrCl 2 catalysts supported on silica, zeolite sodic mordenite (NaM) and acid mordenite (HM). The polymerizations were performed at different temperatures and varying aluminium/zirconium molar ratios ([Al]/[Zr]). The effect of these reaction parameters on the catalyst activity was investigated using a proposed statistical experimental planning. In the case of f 2 C(Flu)(Cp)ZrCl 2 , SiO 2 and NaM were used as support and the catalyst performance evaluated using toluene and pentane as polymerization solvent. The molecular weight, molecular weight distribution, melting point and crystallinity of the polymers were examined. The results indicate very high activities for the syndiospecific heterogeneous system. Also, the polymers obtained had superior Mw and stereo regularity. (author)

Crystal structures of bis[2-(pyridin-2-ylphenyl-κ2N,C1]rhodium(III complexes containing an acetonitrile or monodentate thyminate(1− ligand

Directory of Open Access Journals (Sweden)

Mika Sakate

2016-04-01

Full Text Available The crystal structures of bis[2-(pyridin-2-ylphenyl]rhodium(III complexes with the metal in an octahedral coordination containing chloride and acetonitrile ligands, namely (OC-6-42-acetonitrilechloridobis[2-(pyridin-2-ylphenyl-κ2N,C1]rhodium(III, [RhCl(C11H8N2(CH3CN] (1, thyminate(1− and methanol, namely (OC-6-42-methanol(5-methyl-2,4-dioxo-1,2,3,4-tetrahydropyrimidin-1-ido-κN1bis[2-(pyridin-2-ylphenyl-κ2N,C1]rhodium(III, [Rh(C11H8N2(C5H5N2O2(CH3OH]·CH3OH·0.5H2O (2, and thyminate(1− and ethanol, namely (OC-6-42-ethanol(5-methyl-2,4-dioxo-1,2,3,4-tetrahydropyrimidin-1-ido-κN1bis[2-(pyridin-2-ylphenyl-κ2N,C1]rhodium(III, [Rh(C11H8N2(C5H5N2O2(C2H5OH]·C2H5OH (3, are reported. The acetonitrile complex, 1, is isostructural with the IrIII analog. In complexes 2 and 3, the monodeprotonated thyminate (Hthym− ligand coordinates to the RhIII atom through the N atom, and the resulting Rh—N(Hthym bond lengths are relatively long [2.261 (2 and 2.252 (2 Å for 2 and 3, respectively] as compared to the Rh—N bonds in the related thyminate complexes. In each of the crystals of 2 and 3, the complexes are linked via a pair of intermolecular N—H...O hydrogen bonds between neighbouring Hthym− ligands, forming an inversion dimer. A strong intramolecular O—H...O hydrogen bond between the thyminate(1− and alcohol ligands in mutually cis positions to each other is also observed.

Rhodium platings – experimental study

OpenAIRE

Rudolf, R.; Budić, B.; Stamenković, D.; Čolić, M.; Ivanič, A.; Kosec, B.

2013-01-01

Modern rhodium plating solutions are based on either sulphate or phosphate. Although in theory there are four possible combinations, in practice only three different rhodium electrolytes are used. These are based on dilutions of rhodium sulphate or phosphate concentrates with added sulphuric or phosphoric acid. These processes are be discussed in this paper with a demonstration of Rh platings in the Slovenian firm Zlatarna Celje d.d.

Rhodium platings – experimental study

Directory of Open Access Journals (Sweden)

R. Rudolf

2013-07-01

Full Text Available Modern rhodium plating solutions are based on either sulphate or phosphate. Although in theory there are four possible combinations, in practice only three different rhodium electrolytes are used. These are based on dilutions of rhodium sulphate or phosphate concentrates with added sulphuric or phosphoric acid. These processes are be discussed in this paper with a demonstration of Rh platings in the Slovenian firm Zlatarna Celje d.d.

A rhodium(III)-based inhibitor of autotaxin with antiproliferative activity.

Science.gov (United States)

Kang, Tian-Shu; Wang, Wanhe; Zhong, Hai-Jing; Liang, Jia-Xin; Ko, Chung-Nga; Lu, Jin-Jian; Chen, Xiu-Ping; Ma, Dik-Lung; Leung, Chung-Hang

2017-02-01

Cancer of the skin is by far the most common of all cancers. Melanoma accounts for only about 1% of skin cancers but causes a large majority of skin cancer deaths. Autotaxin (ATX), also known as ectonucleotide pyrophosphatase/phosphodiesterase 2 (ENPP2), regulates physiological and pathological functions of lysophosphatidic acid (LPA), and is thus an important therapeutic target. We synthesized ten metal-based complexes and a novel cyclometalated rhodium(III) complex 1 was identified as an ATX enzymatic inhibitor using multiple methods, including ATX enzymatic assay, thermal shift assay, western immunoblotting and so on. Protein thermal shift assays showed that 1 increased the melting temperature (T m ) of ATX by 3.5°C. 1 also reduced ATX-LPA mediated downstream survival signal pathway proteins such as ERK and AKT, and inhibited the activation of the transcription factor nuclear factor κB (NF-κB) and signal transducer and activator of transcription 3 (STAT3). 1 also exhibited strong anti-proliferative activity against A2058 melanoma cells (IC 50 =0.58μM). Structure-activity relationship indicated that both the rhodium(III) center and the auxiliary ligands of complex 1 are important for bioactivity. 1 represents a promising scaffold for the development of small-molecule ATX inhibitors for anti-tumor applications. To our knowledge, complex 1 is the first metal-based ATX inhibitor reported to date. Rhodium complexes will have the increased attention in therapeutic and bioanalytical applications. Copyright © 2016 Elsevier B.V. All rights reserved.

Identification of a rhodium(iii) complex as a Wee1 inhibitor against TP53-mutated triple-negative breast cancer cells.

Science.gov (United States)

Yang, Guan-Jun; Zhong, Hai-Jing; Ko, Chung-Nga; Wong, Suk-Yu; Vellaisamy, Kasipandi; Ye, Min; Ma, Dik-Lung; Leung, Chung-Hang

2018-03-06

The rhodium(iii) complex 1 was identified as a potent Wee1 inhibitor in vitro and in cellulo. It decreased Wee1 activity and unscheduled mitotic entry, and induced cell damage and death in TP53-mutated triple-negative breast cancer cells. 1 represents a promising scaffold for further development of more potent metal-based Wee1 antagonists.

Industrial tests of rhodium self-powered detectors: the Golfech 2 experimentation

International Nuclear Information System (INIS)

Mourlevat, J.L.; Janvier, D.; Warren, H.D.

2000-01-01

In co-operation with Electricite de France (EDF), FRAMATOME has been testing two in-core strings which are equipped with rhodium self-powered detectors (SPDs) in the Golfech Unit 2 reactor (1300 MW, 4L plant) since August 1997. The rhodium SPDs and the strings which support them were designed and built by the US FRAMATOME subsidiary FRAMATOME-COGEMA-FUEL (FCF). The rhodium signals and some other plant parameters are acquired through the use of a specific device designed by the CEA (Commissariat a l'Energie Atomique) and are processed off-line by FRAMATOME. This demonstration test is planned to last until mid-2000. The following presentation is focused on the results obtained during the first demonstration cycle (from 08/97 to 12/98). The tests that have been conducted consist of checking the rhodium depletion and of comparing the rhodium signals to the movable probes. In order to compensate for the delay in the rhodium signals, a deconvolution algorithm has also been tested. Up to now, the results are very satisfactory and a future large scale industrial application is being discussed with the EDF. The main objective of the next experimentation phase is to test - under industrial conditions - a prototype of an on-line monitoring unit known as the Partial In-Core Monitoring System (PIMS). This system will include 16 rhodium in-core strings and will use an on-line 3-D core model. (authors)

Sulfur tolerant zeolite supported platinum catalysts for aromatics hydrogenation

Energy Technology Data Exchange (ETDEWEB)

Bergem, Haakon

1997-12-31

The increased demand for transportation fuels at the expence of heavier fuel oil has forced the refinery industry to expand their conversion capacity with hydrotreating as one of the key processes. A shift towards more diesel powered vehicles along with tightening fuel regulations demanding cleaner fuels has lead to increasing interest in catalytic processes for the manufacturing of such environmentally acceptable fuels. This provides the motivation for this thesis. Its main objective was to study possible catalysts active for desulfurization, hydrogenation, and ring-opening of aromatics all in the presence of sulfur. A close examination of the physical properties and kinetical behaviour of the chosen catalysts has been performed. A high pressure reactor setup was designed and built for activity measurements. Zeolite supported platinum catalysts were prepared and both the metal and acid functions were characterized utilizing various experimental techniques. Hydrogenation of toluene was used as a model reaction and the effect of sulfur adsorption on the activity and kinetic behaviour of the catalysts was investigated. The catalyst samples showed hydrogenation activities comparable to a commercial Pt/Al2O3 catalyst. There were no clear differences in the effect of the various sulfur compounds studied. Platinum supported on zeolite Y gave considerably more sulfur tolerant catalysts compared to Al2O3 as support. 155 refs., 58 figs., 36 tabs.

Synthesis of zeolite membrane (Y / α-alumina)

International Nuclear Information System (INIS)

Araujo, Ana Paula; Silva, Valmir Jose da; Crispin, Alana Carolyne; Rodrigues, Meiry Glaucia F.; Menezes, Romualdo R.

2009-01-01

The general aim of this study was to develop materials of the type: Y zeolite (hydrothermal synthesis), ceramic support (forming of powder) and zeolite membrane (rubbing). The preparation of the Y zeolite was conducted in accordance with the hydrothermal synthesis method, the time of crystallization was one day. The ceramic support was prepared by means of the forming of powder technique and subsequently subjected to sintering at a temperature of 1400 deg C/1h. The zeolite membrane (Y/α- alumina) was prepared by secondary growth method (rubbing). These materials were characterized by XRD and SEM. Obtaining Y zeolite could be confirmed by X ray diffractograms. From the images obtained by SEM, it was possible to derive from analysis that the Y zeolite is composed of a homogeneous morphology, where the particles are crowded, with uniform size. The results obtained for the ceramic support (α-alumina) showed that it displays characteristics peaks of aluminum oxide. By using micrographs it was possible to observe a heterogeneous microstructure with a compact form, without cracks upon the layers. According to the XRD, for the method of secondary growth (rubbing), it was observed that the Y zeolite which had been synthesized on the ceramic support displayed a crystalline structure. The micrography of the zeolite membrane (Y/α-alumina) showed the formation of a layer of zeolite on the ceramic support. (author)

Hydrodeoxygenation and coupling of aqueous phenolics over bifunctional zeolite-supported metal catalysts.

Science.gov (United States)

Hong, Do-Young; Miller, Stephen J; Agrawal, Pradeep K; Jones, Christopher W

2010-02-21

Pt supported on HY zeolite is successfully used as a bifunctional catalyst for phenol hydrodeoxygenation in a fixed-bed configuration at elevated hydrogen pressures, leading to hydrogenation-hydrogenolysis ring-coupling reactions producing hydrocarbons, some with enhanced molecular weight.

Salt-occluded zeolite waste forms: Crystal structures and transformability

International Nuclear Information System (INIS)

Richardson, J.W. Jr.

1996-01-01

Neutron diffraction studies of salt-occluded zeolite and zeolite/glass composite samples, simulating nuclear waste forms loaded with fission products, have revealed complex structures, with cations assuming the dual roles of charge compensation and occlusion (cluster formation). These clusters roughly fill the 6--8 angstrom diameter pores of the zeolites. Samples are prepared by equilibrating zeolite-A with complex molten Li, K, Cs, Sr, Ba, Y chloride salts, with compositions representative of anticipated waste systems. Samples prepared using zeolite 4A (which contains exclusively sodium cations) as starting material are observed to transform to sodalite, a denser aluminosilicate framework structure, while those prepared using zeolite 5A (sodium and calcium ions) more readily retain the zeolite-A structure. Because the sodalite framework pores are much smaller than those of zeolite-A, clusters are smaller and more rigorously confined, with a correspondingly lower capacity for waste containment. Details of the sodalite structures resulting from transformation of zeolite-A depend upon the precise composition of the original mixture. The enhanced resistance of salt-occluded zeolites prepared from zeolite 5A to sodalite transformation is thought to be related to differences in the complex chloride clusters present in these zeolite mixtures. Data relating processing conditions to resulting zeolite composition and structure can be used in the selection of processing parameters which lead to optimal waste forms

THE THEORY OF DEVELOPMENT OF SUPPORTED METAL-COMPLEX CATALYSTS

Directory of Open Access Journals (Sweden)

T. L. Rakitskaya

2015-06-01

Full Text Available Some results of the investigations for the purpose of development of supported metal-complex catalysts for phosphine and carbon monoxide oxidation as well as for ozone decomposition are summarized. The activity of such catalysts has been found to depend not only on a nature of a central atom and ligands but also on a nature of supports. The theoretical model explaining mechanisms of surface complex formation taking into account the influence of physicochemical and structural-adsorption properties of the supports (SiO2, Al2O3, carbon materials, zeolites, dispersed silicas, lamellar aluminosilicates, etc. has been proposed. For quantitative description of the support effect, such a thermodynamic parameter as the adsorbed water activity assignable with the help of water vapor adsorption isotherms has been introduced. Successive stability constants of the surface metal complexes have been calculated by the kinetic method and, hence, compositions and partial catalytic activity of the latter have been determined. Taking into account the competitive adsorption of metal ions on the supports, some schemes of formation of surface bimetallic complexes have been suggested. The compositions of the supported metal-complex catalysts have been optimized to meet requirements of their use in respirators and plants for air purification from foregoing gaseous toxicants.

Dimerisation, rhodium complex formation and rearrangements of N-heterocyclic carbenes of indazoles

Directory of Open Access Journals (Sweden)

Zong Guan

2014-04-01

Full Text Available Deprotonation of indazolium salts at low temperatures gives N-heterocyclic carbenes of indazoles (indazol-3-ylidenes which can be trapped as rhodium complexes (X-ray analysis. In the absence of Rh, the indazol-3-ylidenes spontaneously dimerize under ring cleavage of one of the N,N-bonds and ring closure to an indazole–indole spiro compound which possesses an exocyclic imine group. The E/Z isomers of the imines can be separated by column chromatography when methanol is used as eluent. We present results of a single crystal X-ray analysis of one of the E-isomers, which equilibrate in solution as well as in the solid state. Heating of the indazole–indole spiro compounds results in the formation of quinazolines by a ring-cleavage/ring-closure sequence (X-ray analysis. Results of DFT calculations are presented.

Reaction pathways for reduction of nitrate ions on platinum, rhodium, and platinum-rhodium alloy electrodes

International Nuclear Information System (INIS)

Cunha, M.C.P.M. da; De Souza, J.P.I.; Nart, F.C.

2000-01-01

The reduction of nitrate ions on platinum, rhodium, and platinum-rhodium alloy electrodes has been investigated using differential electrochemical mass spectrometry and in situ FTIR measurements. For 3 M HNO 3 concentration it has been found that nitrate starts the reduction with partial N-O bond dissociation and N-N bond formation generating NO and N 2 O. At potentials lower than 0.2 V the reaction proceeds forming dissolved NH 4 + . For potentials lower than 0 V the reduction continues via a multiple pathway reaction leading to the nonselective production of N 2 , NH 2 OH, and N 2 H 2 . On the alloyed electrodes, the production of NO and N 2 O has been observed in both cathodic and anodic scans, while on pure platinum and rhodium electrodes the reaction has been observed only during the cathodic scan. Contrasting with the pure platinum and rhodium alloys, where the N-O bond break starts forming NO and N 2 O, on the alloys HNO 2 has been observed as the first reaction step. For alloys with higher rhodium composition, like Pt 75 Rh 25 , no N 2 has been detected for potentials lower than 0 V

Carbon monoxide hydrogenation over ruthenium zeolites

Energy Technology Data Exchange (ETDEWEB)

Jacobs, P.A.; Nijs, H.H.; Verdonck, J.J.; Uytterhoeven, J.B.

1978-03-01

Ru zeolites are active and stable methanation catalysts. Under Fischer--Tropsch conditions they show a narrow product distribution. Further work is needed to assign this to a possible effect exerted by the zeolite cages. When the size of the Ru particles enclosed in the zeolite cages is increased, a lower methanation activity is found and a higher amount of C/sub 2/ and C/sub 3/ products are formed under Fischer--Tropsch conditions. This effect has not been reported until now on other supports. The less acidic zeolites act as promoters of the CO hydrogenation: under methanation conditions the activity is increased; under Fischer--Tropsch conditions, the selectivity is shifted toward higher hydrocarbons. This is explained by the particular zeolite property that electron deficient metal agglomerates seem to be formed on the acidic zeolites. With respect to kinetic behavior, relative activity of different metals, influence of reaction temperature on product distribution, the zeolite behaves in the same way a conventional alumina support. 4 figs., 4 tables.

Physicochemical impact of zeolites as the support for photocatalytic hydrogen production using solar-activated TiO2-based nanoparticles

International Nuclear Information System (INIS)

Taheri Najafabadi, Amin; Taghipour, Fariborz

2014-01-01

Highlights: • Zeolite chemical properties are crucial to photocatalytic hydrogen production. • Basic zeolite, TiO 2 , heteropolyacid and cobalt together are active under visible light. • TiO 2 impregnation on zeolite causes band gap widening and band edges’ anodic shift. • Heteropolyacid enhances the visible light activity of the photocatalyst. • Zeolite’s basicity can overshadow the anodic shift, advancing hydrogen evolution. - Abstract: Silico-aluminates (zeolites) have been recently utilized promisingly as the support for photocatalytic hydrogen production using solar-activated TiO 2 -based nanoparticles. Aside from conventional advantages offered by the supports in photocatalysis, we demonstrate the unique physicochemical impact of zeolites on photocatalytic hydrogen production. Beside zeolites, our synthesized materials comprise titanium dioxide (TiO 2 ) as the semiconductor, cobalt ions as the hydrogen evolution sites, and heteropolyacids (HPAs) as the multifunctional solid acids with significant excitability under visible light. Four classes of zeolites (Na-Y, Na-mordenite, H-Y, and H-beta) with different Si/Al ratios and sodium contents were evaluated. Among the studied photocatalysts, Na-Y and Na-mordenite containing 10 wt% titania emerged as the potential candidates for the hydrogen evolution reaction, with corresponding rates of 250.8 and 187.2 μmol/g h, in comparison to 84.2 μmol/g h for Degussa P25; while these values for H-Y and H-beta were 96.8 and 100.1 μmol/g h, respectively. The higher photocatalytic activity of the first two classes is attributed to the basicity of the zeolite matrix, which is possibly due to the pH dependency of the TiO 2 band edges. The results indicate the importance of controlling the chemical properties of the zeolite as a photocatalyst support through the selection of suitable types. Furthermore, our analyses show that the precise pore size distribution of the zeolite framework rules over accommodating the

Distribution of Rhodium in Mice Submitted to Treatment With the Adduct of Rhodium Propionate and Sodium Isonicotinate

OpenAIRE

de Souza, Aparecido Ribeiro; Najjar, Renato; de Oliveira, Elizabeth; Zyngier, Szulim Ber

1997-01-01

The distribution of rhodium in Balb/c mice following intraperitoneal (ip) administration of a solution of adduct of rhodium propionate and sodium isonicotinate has been investigated. The metal concentration was determined in blood and in the following organ tissues: brain, heart, lung, liver, spleen, kidney, testes, and uterus/ovary, and the rhodium concentration was obtained by Inductively Coupled Argon Atomic Emission Spectroscopy (ICP-AES). The metal was detected in all organ tissues exami...

A rhodium(III) complex for high-affinity DNA base-pair mismatch recognition

Science.gov (United States)

Junicke, Henrik; Hart, Jonathan R.; Kisko, Jennifer; Glebov, Oleg; Kirsch, Ilan R.; Barton, Jacqueline K.

2003-01-01

A rhodium(III) complex, rac-[Rh(bpy)2phzi]3+ (bpy, 2,2′-bipyridine; phzi, benzo[a]phenazine-5,6-quinone diimine) has been designed as a sterically demanding intercalator targeted to destabilized mismatched sites in double-helical DNA. The complex is readily synthesized by condensation of the phenazine quinone with the corresponding diammine complex. Upon photoactivation, the complex promotes direct strand scission at single-base mismatch sites within the DNA duplex. As with the parent mismatch-specific reagent, [Rh(bpy)2(chrysi)]3+ [chrysene-5,6-quinone diimine (chrysi)], mismatch selectivity depends on the helix destabilization associated with mispairing. Unlike the parent chrysi complex, the phzi analogue binds and cleaves with high affinity and efficiency. The specific binding constants for CA, CC, and CT mismatches within a 31-mer oligonucleotide duplex are 0.3, 1, and 6 × 107 M−1, respectively; site-specific photocleavage is evident at nanomolar concentrations. Moreover, the specificity, defined as the ratio in binding affinities for mispaired vs. well paired sites, is maintained. The increase in affinity is attributed to greater stability in the mismatched site associated with stacking by the heterocyclic aromatic ligand. The high-affinity complex is also applied in the differential cleavage of DNA obtained from cell lines deficient in mismatch repair vs. those proficient in mismatch repair. Agreement is found between photocleavage by the mismatch-specific probes and deficiency in mismatch repair. This mismatch-specific targeting, therefore, offers a potential strategy for new chemotherapeutic design. PMID:12610209

Scalar Relativistic Study of the Structure of Rhodium Acetate

Directory of Open Access Journals (Sweden)

Emily E. Edwards

2004-01-01

Full Text Available Abstract: Rhodium acetate, related rhodium carboxylates, and rhodium amide complexes are powerful catalysts for carbene chemistry. They readily promote the decomposition of diazo compounds and transfer the resulting carbene to a variety of substrates. There have been several quantum chemistry studies of these compounds, particularly of the acetate. These have all used non-relativistic methods, and all have shown optimized Rh-Rh bond lengths significantly longer than the experimental value. In this study we have surveyed several scalar relativistic DFT methods using Gaussian, Slater, and numerical basis functions (in DGAUSS, ADF, and DMOL3. Several combinations of exchange-correlation functionals with relativistic and non-relativistic effective core potentials (ECP were investigated, as were non-relativistic and all electron scalar relativistic methods. The combination of the PW91 exchange and PW91 correlation functional with the Christiansen-Ermler ECP gave the best results: 2.3918 Å compared to the experimental value of 2.3855±0.0005 Å.

Separation of carrier-free rhodium isotopes from ruthenium cyclotron targets by the extraction of nitrosylruthenium from hydrochloric acid solution

International Nuclear Information System (INIS)

Haasbroek, F.J.; Strelow, F.W.E.; Van der Walt, T.N.

1981-01-01

A method is presented for the separation of rhodium isotopes from ruthenium cyclotron targets. After bombardment with deuterons and dissolution of the target material, the ruthenium is converted into a nitrosyl complex by treatment with hydroxylammonium chloride. Aluminium and other elements which have been introduced in the dissolution step, are separated by cation exchange. Ruthenium is then separated by extraction with a mixture of tri-n-butyl phosphate and hexane (4:1), leaving the rhodium in the aqueous phase. No ruthenium is found in the rhodium fraction and the recovery of rhodium is better than 90 per cent [af

Method of producing zeolite encapsulated nanoparticles

DEFF Research Database (Denmark)

2015-01-01

The invention therefore relates to a method for producing zeolite, zeolite-like or zeotype encapsulated metal nanoparticles, the method comprises the steps of: 1) Adding one or more metal precursors to a silica or alumina source; 2) Reducing the one or more metal precursors to form metal...... nanoparticles on the surface of the silica or alumina source; 3) Passing a gaseous hydrocarbon, alkyl alcohol or alkyl ether over the silica or alumina supported metal nanoparticles to form a carbon template coated zeolite, zeolite-like or zeotype precursor composition; 4a) Adding a structure directing agent...... to the carbon template coated zeolite, zeolite-like or zeotype precursor composition thereby creating a zeolite, zeolite-like or zeotype gel composition; 4b) Crystallising the zeolite, zeolite-like or zeotype gel composition by subjecting said composition to a hydrothermal treatment; 5) Removing the carbon...

Method for producing zeolites and zeotypes

DEFF Research Database (Denmark)

2015-01-01

The invention relates to a method for producing zeolite, zeolite-like or zeotype particles comprising the steps of: 1 ) Adding one or more metal precursors to a silica or alumina source; 2) Reducing the one or more metal precursors to form metal nanoparticles on the surface of the silica or alumina...... source; 3) Passing a gaseous hydrocarbon, alkyl alcohol or alkyl ether over the silica or alumina supported metal nanoparticle to form a carbon template coated zeolite, zeolite-like or zeotype precursor composition; 4a) Adding a structure directing agent to the carbon template coated zeolite, zeolite......-like or zeotype precursor composition thereby creating a zeolite, zeolite-like or zeotype gel composition; 4b) Crystallising the zeolite, zeolite-like or zeotype gel composition by subjecting said composition to a hydrothermal treatment; 5) Removing the carbon template and structure directing agent and isolating...

Rhodium mediated bond activation: from synthesis to catalysis

Energy Technology Data Exchange (ETDEWEB)

Ho, Hung-An [Iowa State Univ., Ames, IA (United States)

2012-01-01

Recently, our lab has developed monoanionic tridentate ligand, To^R, showing the corresponding coordination chemistry and catalyst reactivity of magnesium, zirconium, zinc and iridium complexes. This thesis details synthetic chemistry, structural study and catalytic reactivity of the To^R-supported rhodium compounds. Tl[To^R] has been proved to be a superior ligand transfer agent for synthesizing rhodium complexes. The salt metathesis route of Tl[To^M] with [Rh(μ-Cl)(CO)]₂ and [Rh(μ- Cl)(COE)]₂ gives To^MRh(CO)₂ (2.2) and To^MRhH(β³-C₈H₁₃) (3.1) respectively while Tl[To^M] with [Rh(μ-Cl)(CO)]₂ affords To^PRh(CO)₂ (2.3). 2.2 reacts with both strong and weak electrophiles, resulting in the oxazoline N-attacked and the metal center-attacked compounds correspondingly. Using one of the metal center-attacked electrophiles, 2.3 was demonstrated to give high diastereoselectivity. Parallel to COE allylic C-H activation complex 3.1, the propene and allylbenzene allylic C-H activation products have also been synthesized. The subsequent functionalization attempts have been examined by treating with Brønsted acids, Lewis acids, electrophiles, nucleophiles, 1,3-dipolar reagents and reagents containing multiple bonds able to be inserted. Various related complexes have been obtained under these conditions, in which one of the azide insertion compounds reductively eliminates to give an allylic functionalization product stoichiometrically. 3.1 reacts with various primary alcohols to give the decarbonylation dihydride complex To^MRh(H)₂CO (4.1). 4.1 shows catalytic reactivity for primary alcohol decarbonylation under a photolytic condition. Meanwhile, 2.2 has been found to be more reactive than 4.1 for catalytic alcohol decarbonylation under the same condition. Various complexes and primary

Modifiers in rhodium catalysts for carbon monoxide hydrogenation: Structure-activity relationships

Energy Technology Data Exchange (ETDEWEB)

Bhore, N. A.

1989-05-01

This report is aimed at identifying interesting modified rhodium systems and elucidating structure-activity relationships in these systems with the overall goal of understanding the scientific issues in the catalytic conversion of syngas to oxygenates. Specific additives (sodium and molybdenum) are selected based on the scoping experiments. The effect of the additives on supported rhodium catalysts is then investigated. Throughout the investigation, experiments and analysis were performed on real systems instead of ideal systems. 374 refs., 82 figs., 57 tabs.

Characterization of NaA Zeolite Oxygen Permeable Membrane on TiO2/α-Al2O3 Composite Support

Directory of Open Access Journals (Sweden)

Zhu Mengfu

2016-01-01

Full Text Available The NaA zeolite membrane was synthesized on the surface of TiO2/α-Al2O3 composite support with TiO2 as modifier of α-Al2O3 porous tubular ceramic membrane support by crystallization method. The structure characterization indicated that the TiO2 of the support surface could effectively improve the surface properties of the support. It didn’t affect the crystallization of NaA synthesis liquid and synthesis process of NaA zeolite membrane. There were no obvious defects between the crystal particles with size of approximate 6μm. The perfect and complete membrane with thickness of approximate 15μm combined closely with support to connection together by TiO2 modified. The oxygen permeability of the membrane on TiO2/α-Al2O3 composite support improves of 47% compared with that of α-Al2O3 support. So the process of TiO2 modifying the surface of α-Al2O3 support should increase the oxygen permeability of the NaA zeolite membrane.

Synthesis and characterization of 12-phosphotungstic acid supported on BEA zeolite

Energy Technology Data Exchange (ETDEWEB)

Jović, A.; Bajuk-Bogdanović, D.; Nedić Vasiljević, B. [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Milojević-Rakić, M., E-mail: maja@ffh.bg.ac.rs [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Krajišnik, D. [Department of Pharmaceutical Technology and Cosmetology, University of Belgrade-Faculty of Pharmacy, Vojvode Stepe 450, 11000 Belgrade (Serbia); Dondur, V. [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Popa, A. [Institute of Chemistry Timisoara, Bl. Mihai Viteazul 24, 300223 Timisoara (Romania); Uskoković-Marković, S. [Department of Analytical Chemistry, University of Belgrade-Faculty of Pharmacy, Vojvode Stepe 450, 11000 Belgrade (Serbia); Holclajtner-Antunović, I. [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia)

2017-01-15

An optimized synthetic route for obtaining heteropoly acid (HPA) species supported on BEA zeolite was applied, and different samples, comprising 20 to 50 wt% of 12-phosphotungstic acid (HPW) were prepared. The as-synthesized supported HPW were subjected to different post-synthesis routes, which involved calcination and ultrasound treatment. Characterization of these materials was performed by means of Scanning Electron Microscopy, zeta potential measurements, Infrared Spectroscopy and X-ray Powder Diffraction analysis. Results suggest strong interaction of HPW with the support and revealed that ultrasound treatment resulted in better dispersion of active phase and thus homogeneous morphology of the samples. The zeta potential was found to be dependent on the preparation procedure and HPW content in these materials, while higher HPW loadings induced its agglomeration. Catalytic activity of the synthesized materials was investigated in an ethanol dehydration reaction, where lower HPW loadings induced higher ethanol conversion. Acid sites distribution and accessibility for ethanol molecules were found to be more essential for catalytic activity than HPW loadings, i.e., amount of active sites present in these hybrid materials. - Highlights: • An optimized route for supporting heteropoly acid on beta zeolite is applied. • Ultrasound treatment of the composites gives dispersed morphology. • Lower heteropoly acid amount induces higher conversion in ethanol dehydration. • Acid sites distribution and accessibility for ethanol are essential for catalytic activity.

Synthesis and characterization of 12-phosphotungstic acid supported on BEA zeolite

International Nuclear Information System (INIS)

Jović, A.; Bajuk-Bogdanović, D.; Nedić Vasiljević, B.; Milojević-Rakić, M.; Krajišnik, D.; Dondur, V.; Popa, A.; Uskoković-Marković, S.; Holclajtner-Antunović, I.

2017-01-01

An optimized synthetic route for obtaining heteropoly acid (HPA) species supported on BEA zeolite was applied, and different samples, comprising 20 to 50 wt% of 12-phosphotungstic acid (HPW) were prepared. The as-synthesized supported HPW were subjected to different post-synthesis routes, which involved calcination and ultrasound treatment. Characterization of these materials was performed by means of Scanning Electron Microscopy, zeta potential measurements, Infrared Spectroscopy and X-ray Powder Diffraction analysis. Results suggest strong interaction of HPW with the support and revealed that ultrasound treatment resulted in better dispersion of active phase and thus homogeneous morphology of the samples. The zeta potential was found to be dependent on the preparation procedure and HPW content in these materials, while higher HPW loadings induced its agglomeration. Catalytic activity of the synthesized materials was investigated in an ethanol dehydration reaction, where lower HPW loadings induced higher ethanol conversion. Acid sites distribution and accessibility for ethanol molecules were found to be more essential for catalytic activity than HPW loadings, i.e., amount of active sites present in these hybrid materials. - Highlights: • An optimized route for supporting heteropoly acid on beta zeolite is applied. • Ultrasound treatment of the composites gives dispersed morphology. • Lower heteropoly acid amount induces higher conversion in ethanol dehydration. • Acid sites distribution and accessibility for ethanol are essential for catalytic activity.

EXAFS study of Mo2N and Mo nitrides supported on zeolites

International Nuclear Information System (INIS)

Liu Zhenlin; Meng Ming; Fu Yilu; Jiang Ming; Hu Tiandou; Xie Yaning; Liu Tao

2002-01-01

In the present study, the reaction is applied to prepare molybdenum nitrides with high surface area, and zeolites are used as supports. The EXAFS of the Mo K-absorption edge is measured and the change of coordination environment of Mo atoms before and after the nitridation is revealed

Transient-response study of CO insertion into CHx surface intermediates on a vanadium-promoted rhodium catalyst

NARCIS (Netherlands)

Koerts, T.; Santen, van R.A.

1992-01-01

The rate of CO insertion into surface CHx species was investigated on silica-supported rhodium and rhodium-vanadium catalysts. Isotopically labelled 13CO was used in a transient kinetic experiment under steady-state conditions. A main conclusion is that vanadium promotion does not affect the rate of

Encapsulation of ferro- and ferricyanide complexes inside ZSM-5 zeolite synthesized from rice straw: Implications for synthesis of Prussian blue pigment

International Nuclear Information System (INIS)

Ali, Ibraheem O.; Salama, Tarek M.; Thabet, Mohamed S.; El-Nasser, Karam S.; Hassan, Ali M.

2013-01-01

Encapsulation of [Fe(CN) 6 ] 4− and [Fe(CN) 6 ] 3− complexes in the intracrystalline pores of ZSM-5 zeolite, Fe II L/Z and Fe III L/Z respectively, by the zeolite synthesis method was reported. The modified zeolites were characterized by powder XRD, FT-IR and UV–vis spectroscopy. The nitrogen adsorption isotherms allow for the evaluation of pore structure of the complex-modified zeolites, whereas the thermal analysis (TGA/DTA) measurements provide insight into the decomposition products of the immobilized complexes. The modified zeolites exhibited smaller pore volumes and surface areas as compared with those of unpromoted ZSM-5, suggesting the inclusion of iron cyanides inside the interconnecting channels of ZSM-5. While the ferricyanide complex enhanced the formation of highly crystalline zeolite, the ferrocyanide one resulted in a lesser effect. The electronic spectra of the colloidal species developed when Fe III L/Z brought in contact with an aqueous solution of [Fe(CN) 6 ] 3− exhibit absorptions attributed to CN − → iron charge-transfer. New bands at 294 and 319 nm due to d–d transitions of Fe III tetrahedral monomeric moieties were emitted concurrently under successive adsorption of [Fe(CN) 6 ] aq 3− over Fe III L/Z, along with a broad band at 555 nm assigned to polymeric [Fe II –C–N–Fe III ] of Prussian blue (PB). The FT-IR spectra of Fe III/II L/Z devoted to the adsorption of an aqueous solution of [Fe(CN) 6 ] 3− showed a band at 2092 cm −1 assigned to the C–N stretch in the Fe II –CN–Fe III linkages. The vibrations attributable to Fe–O–Si bonding along with hydrocarbon and nitroprusside appeared only in the spectrum of Fe III L/Z, thus was found to be strong evidence for the mutual interaction between [Fe(CN) 6 ] 3− and the latter sample. - Highlights: • We synthesized ferrous and ferric cyanide complexes inside ZSM-5 zeolite. • The decomposition of the encapsulated complexes occurred at high temperatures. �

Tetramethyl(perfluoroalkyl)cyclopentadienyl Rhodium(I) Complexes with Ethylene or Diene Ligands. Crystal Structure of [(eta-5-C5Me4C6F13)Rh(CO)2

Czech Academy of Sciences Publication Activity Database

Čermák, Jan; Krupková, Alena; Auerová, Kateřina; Zamrzla, M.; Nguyen Thi, T.H.; Vojtíšek, P.; Císařová, I.

2010-01-01

Roč. 695, č. 3 (2010), s. 375-381 ISSN 0022-328X R&D Projects: GA AV ČR IAA4072203; GA MŠk(CZ) LC06070 Institutional research plan: CEZ:AV0Z40720504 Keywords : fluorous cyclopentadienes * rhodium complexes * alkene complexes Subject RIV: CC - Organic Chemistry Impact factor: 2.205, year: 2010

Application of zeolite-based catalyst to hydrocracking of coal-derived liquids

Energy Technology Data Exchange (ETDEWEB)

Shimada, H.; Sato, T.; Yoshimura, Y.; Hinata, A.; Yoshitomi, S.; Castillo Mares, A.; Nishijima, A. (National Chemical Laboratory for Industry, Tsukuba (Japan))

1990-06-01

Y-zeolite supported catalysts were applied to the hydrocracking of coal-derived liquids. By the introduction of two-stage upgrading consisting of hydrotreating and hydrocracking, Wandoan coal-derived middle distillate was hydrocracked over Ni-Mo/Y-zeolite, producing a high gasoline fraction yield. Zeolite supported catalysts gave little hydrocracked compounds in the hydroprocessing of coal-derived heavy oils, even after hydrotreatment. The reaction inhibitors which seriously poison the active sites of zeolites were found to be small nitrogen-containing molecules. In the hydroprocessing of coal-derived heavy oils, zeolite supported catalysts were inferior to alumina supported catalysts. This is due to the high hydrocracking but low hydrogenation activity of zeolite supported catalysts. 22 refs., 5 figs., 11 tabs.

Correction of rhodium detector signals for comparison to design calculations

International Nuclear Information System (INIS)

Judd, J.L.; Chang, R.Y.; Gabel, C.W.

1989-01-01

Rhodium detectors are used in many commercial pressurized water reactors PWRs [pressurized water reactor] as in-core neutron detectors. The signals from the detectors are the result of neutron absorption in 103 Rh and the subsequent beta decay of 104 Rh to 104 Pd. The rhodium depletes ∼1% per full-power month, so corrections are necessary to the detector signal to account for the effects of the rhodium depletion. These corrections result from the change in detector self-shielding with rhodium burnup and the change in rhodium concentration itself. Correction for the change in rhodium concentration is done by multiplication of the factor N(t)/N 0 , where N(t) is the rhodium concentration at time t and N 0 is the initial rhodium concentration. The calculation of the self-shielding factor is more complicated and is presented. A self-shielding factor based on the fraction of rhodium remaining was calculated with the CASMO-3 code. The results obtained from our comparisons of predicted and measured in-core detector signals show that the CASMO-3/SIMULATE-3 code package is an effective tool for estimating pin peaking and power distributions

Metal supported on natural zeolite as catalysts for conversion of ethanol to gasoline

Directory of Open Access Journals (Sweden)

Kristiani Anis

2017-01-01

Full Text Available A various of metal supported into natural zeolite was prepared via wet impregnation method. The transition metals impregnated are nickel, cobalt, copper and zinc. The catalytic properties both of physical and chemical properties were characterized by X-ray Diffraction (XRD, Thermo Gravimetri Analysis (TGA-Differential Scanning Calorimetry (DSC, Surface Area Analyzer-Porositymeter and also gravimetry method for acidity measurement following by the adsorption of organic bases. The results showed that different metals impregnated into natural zeolite affected physical and chemical properties, i.e. crystalinity, surface area, pore size, pore volume and acidity. Their catalytic activity was tested for conversion ethanol to gasoline and showed high conversion up to 80-90% with the aromatics as major product.

A monofunctional platinum complex coordinated to a rhodium metalloinsertor selectively binds mismatched DNA in the minor groove.

Science.gov (United States)

Weidmann, Alyson G; Barton, Jacqueline K

2015-10-05

We report the synthesis and characterization of a bimetallic complex derived from a new family of potent and selective metalloinsertors containing an unusual Rh-O axial coordination. This complex incorporates a monofunctional platinum center containing only one labile site for coordination to DNA, rather than two, and coordinates DNA nonclassically through adduct formation in the minor groove. This conjugate displays bifunctional, interdependent binding of mismatched DNA via metalloinsertion at a mismatch as well as covalent platinum binding. DNA sequencing experiments revealed that the preferred site of platinum coordination is not the traditional N7-guanine site in the major groove, but rather N3-adenine in the minor groove. The complex also displays enhanced cytotoxicity in mismatch repair-deficient and mismatch repair-proficient human colorectal carcinoma cell lines compared to the chemotherapeutic cisplatin, and it triggers cell death via an apoptotic pathway, rather than the necrotic pathway induced by rhodium metalloinsertors.

Complex Reaction Environments and Competing Reaction Mechanisms in Zeolite Catalysis: Insights from Advanced Molecular Dynamics

NARCIS (Netherlands)

De Wispelaere, K.; Ensing, B.; Ghysels, A.; Meijer, E.J.; van Van Speybroeck, V.

2015-01-01

The methanol-to-olefin process is a showcase example of complex zeolite-catalyzed chemistry. At real operating conditions, many factors affect the reactivity, such as framework flexibility, adsorption of various guest molecules, and competitive reaction pathways. In this study, the strength of first

A Rhodium(III) Complex as an Inhibitor of Neural Precursor Cell Expressed, Developmentally Down-Regulated 8-Activating Enzyme with in Vivo Activity against Inflammatory Bowel Disease.

Science.gov (United States)

Zhong, Hai-Jing; Wang, Wanhe; Kang, Tian-Shu; Yan, Hui; Yang, Yali; Xu, Lipeng; Wang, Yuqiang; Ma, Dik-Lung; Leung, Chung-Hang

2017-01-12

We report herein the identification of the rhodium(III) complex [Rh(phq) 2 (MOPIP)] + (1) as a potent and selective ATP-competitive neural precursor cell expressed, developmentally down-regulated 8 (NEDD8)-activating enzyme (NAE) inhibitor. Structure-activity relationship analysis indicated that the overall organometallic design of complex 1 was important for anti-inflammatory activity. Complex 1 showed promising anti-inflammatory activity in vivo for the potential treatment of inflammatory bowel disease.

Preparation of rhodium target for cyclone-30 accelerator

International Nuclear Information System (INIS)

Deng Xuesong; Li Dakang; Xie Xiangqian; Li Chao

2002-01-01

The rhodium target for Cyclone-30 accelerator is prepared by pulse electroplating method. The effects of pulse parameters, rhodium concentration, acidity and temperature on the properties of the target layer are studied, and the optimal process is determined. The rhodium target, mass thickness is more than 150 mg/cm 2 , adapts to producing 103 Pd on Cyclone-30 accelerator

for zeolite coating

Directory of Open Access Journals (Sweden)

Carlos Renato Rambo

2006-01-01

Full Text Available Biotemplating is the processing of microcellular ceramics by reproduction of natural morphologies, where the microstructural features of the biotemplate are maintained in the biomorphic ceramic. Different biotemplates with distinct pore anatomies were used to produce biomorphic supports for the zeolite coating: wood, cardboard, sea-sponge and sisal. The biomorphic ceramics were produced by distinguished processing routes: Al-gas infiltration-reaction, liquid-metal infiltration, dip-coating and sol-gel synthesis, in order to produce nitrides, carbides and oxides, depending on the processing conditions. The zeolite coating was performed by hydrothermal growth of MFI-type (Silicalite-1 and ZSM-5 zeolite crystals onto the internal pore walls of the biomorphic templates. The final biomorphic ceramic-zeolite composites were physically characterized, evaluated in terms of their gas adsorption capabilities and correlated to their microstructure and specific pore anatomy. The combination of the properties of the biomorphic ceramics with the adsorption properties of zeolites results in materials with distinct properties as potential candidates for adsorption and catalytic applications due to their characteristic porosity, molecular sieving capabilities and high thermo-mechanical strength.

Encapsulation of ferro- and ferricyanide complexes inside ZSM-5 zeolite synthesized from rice straw: Implications for synthesis of Prussian blue pigment

Energy Technology Data Exchange (ETDEWEB)

Ali, Ibraheem O.; Salama, Tarek M., E-mail: tm_salama@yahoo.com; Thabet, Mohamed S.; El-Nasser, Karam S.; Hassan, Ali M.

2013-06-15

Encapsulation of [Fe(CN){sub 6}]{sup 4−} and [Fe(CN){sub 6}]{sup 3−} complexes in the intracrystalline pores of ZSM-5 zeolite, Fe{sup II}L/Z and Fe{sup III}L/Z respectively, by the zeolite synthesis method was reported. The modified zeolites were characterized by powder XRD, FT-IR and UV–vis spectroscopy. The nitrogen adsorption isotherms allow for the evaluation of pore structure of the complex-modified zeolites, whereas the thermal analysis (TGA/DTA) measurements provide insight into the decomposition products of the immobilized complexes. The modified zeolites exhibited smaller pore volumes and surface areas as compared with those of unpromoted ZSM-5, suggesting the inclusion of iron cyanides inside the interconnecting channels of ZSM-5. While the ferricyanide complex enhanced the formation of highly crystalline zeolite, the ferrocyanide one resulted in a lesser effect. The electronic spectra of the colloidal species developed when Fe{sup III}L/Z brought in contact with an aqueous solution of [Fe(CN){sub 6}]{sup 3−} exhibit absorptions attributed to CN{sup −} → iron charge-transfer. New bands at 294 and 319 nm due to d–d transitions of Fe{sup III} tetrahedral monomeric moieties were emitted concurrently under successive adsorption of [Fe(CN){sub 6}]{sub aq}{sup 3−} over Fe{sup III}L/Z, along with a broad band at 555 nm assigned to polymeric [Fe{sup II}–C–N–Fe{sup III}] of Prussian blue (PB). The FT-IR spectra of Fe{sup III/II}L/Z devoted to the adsorption of an aqueous solution of [Fe(CN){sub 6}]{sup 3−} showed a band at 2092 cm{sup −1} assigned to the C–N stretch in the Fe{sup II}–CN–Fe{sup III} linkages. The vibrations attributable to Fe–O–Si bonding along with hydrocarbon and nitroprusside appeared only in the spectrum of Fe{sup III}L/Z, thus was found to be strong evidence for the mutual interaction between [Fe(CN){sub 6}]{sup 3−} and the latter sample. - Highlights: • We synthesized ferrous and ferric cyanide

Spectrophotometric determination of ruthenium (III) and rhodium (III) with 9,10-phenanthrenequinone monoxime after extraction into molten naphthalene

International Nuclear Information System (INIS)

Wasey, A.; Bansal, R.K.; Puri, B.K.; Satake, Masatada.

1983-01-01

9,10-Phenanthrenequinone monoxime has been used as a reagent for the spectrophotometric determination of ruthenium(III) and rhodium(III) after extraction into molten naphthalene. The extracted mixture of the metal complex and naphthalene was dissolved in chloroform and ruthenium and rhodium were determined spectrophotometrically. Beer's law holds in the concentration range of 0.2-4.1 μg/cm 3 for ruthenium and 0.3-5.3 μg/cm 3 for rhodium in 10 cm 3 of the final solution. The molar absorptivities and Sandell sensitivities are calculated to be 9.70 x 10 3 l mol -1 cm -1 and 0.01 μg/cmsup(2 ) (660 nm) for ruthenium and 1.13 x 10 4 l mol -1 cm -1 and 0.009 μg/cm 2 (410 nm) for rhodium respectively. Aliquots containing 2.0 μg of ruthenium and 4.1 μg of rhodium give mean absorbances of 0.192 and 0.451 with standard deviations of 0.0017 and 0.0039, respectively. Interference of various ions has been studied and the method has been applied to the determination of ruthenium and rhodium in various synthetic mixtures. This procedure is also applied to the simultaneous determination of ruthenium and rhodium present together in a solution. (author)

Catalytic upgrading of oleic acid into biofuel using Mo modified zeolite supported Ni oxalate catalyst functionalized with fluoride ion

International Nuclear Information System (INIS)

Ayodele, O.B.; Abbas, Hazzim F.; Daud, Wan Mohd Ashri Wan

2014-01-01

Highlights: • Modification of zeolite with freshly prepared molybdenum oxalate. • Functionalization of Ni oxalate with HF and incorporation into Mo modified zeolite. • Characterization of synthesized Mo modified zeolite supported Ni oxalate catalyst. • Deoxygenation of oleic acid with the synthesized zeolite supported catalyst. • Reusability study on the synthesized zeolite supported catalyst. - Abstract: In this study, fluoride ion functionalized nickel oxalate supported on molybdenum modified zeolite (NiMoFOx/Zeol) catalyst was synthesized, characterized and tested on the hydrodeoxygenation (HDO) of oleic acid (OA) into paraffinic fuel. The NiMoFOx/Zeol characterization results confirmed the presence of both Ni and Mo as well as the formation of NiMoO 4 which is a highly HDO reactive specie at 2θ value of 43.6° according to the XRD result. NiMoFOx/Zeol also showed loss in crystallinity and reduction in the average particle size leading to increase in the pore volume and specific surface area due to the combined effects of fluoride ion presence, oxalic acid functionalization and calcination. The effect of temperature, pressure and NiMoFOx/Zeol loading studied showed that initial increase in their values increased the yield of the target fractions until some points where reduction was observed. The best observed experimental conditions to hydrodeoxygenate 40 g (∼45 mL) of OA into 75% n-C 18 and 23% i-C 18 were 360 °C, 30 mg NiMoFOx/Zeol loading and 20 bar using 100 mL H 2 /min. The presence of i-C 18 was due to the functionalization of the catalyst with fluoride ion. The catalyst reusability result displayed excellent qualities with marginal loss of only 2% in activity after third reuse due to the improved synthesis protocol that employed organometallic precursor. The results are strongly encouraging for further studies toward industrialization of HDO process

Obtaining of supports macro and micro nutrients with base in zeolites mexicans

International Nuclear Information System (INIS)

Cordova H, A.; Islas M, M.; Bascunan S, C.; Martines G, M.; Nikolaev N, S.

2001-01-01

Study the effect of application of the zeolites modified by the ionico interchange with fertilizers (NPK), N-p in the production of tomatos. The cultive of tomatos was made in lands of the Benemerita Autonoma Universidad de Puebla, Mexico, taking equal quadrants with the following ground treatments: 1) zeolite interchanged with fertilizers, 2) zeolite interchanged with a solution that contained only N-p, 3) natural zeolite without ionica modification and a quadrant witness represented by the ground without treatment. The collected data show an increase in the harvest of tomatos, as well as the retention of the decomposition of the harvested tomatos. In addition, it determinated that the optimal concentrations in the case of the zeolite dealt with 3% of fertilizer NPK are: 0,91% of potassium and 0.61% of nitrogen. These results allow to suggest the use of zeolites modified by ionico interchange in agriculture to elevate the level of the harvests of the tomato [es

Dihydropyranone Formation by Ipso C–H Activation in a Glucal 3-Carbamate-Derived Rhodium Acyl Nitrenoid

Science.gov (United States)

Hurlocker, Brisa; Abascal, Nadia C.; Repka, Lindsay M.; Santizo-Deleon, Elsy; Smenton, Abigail L.; Baranov, Victoria; Gupta, Ritu; Bernard, Sarah E.; Chowdhury, Shenjuti; Rojas, Christian M.

2011-01-01

By using (N-tosyloxy)-3-O-carbamoyl-D-glucal 10, which removes the need for a hypervalent iodine(III) oxidant, we provide evidence for rhodium nitrenoid-mediated ipso C–H activation as the origin of a C3-oxidized dihydropyranone product 3. This system may be especially susceptible to such a pathway due to the ease of forming a cation upon hydride transfer to the rhodium-complexed acyl nitrene. PMID:21381715

Evaluation of photocatalytic activities of supported catalysts on NaX zeolite or activated charcoal

Energy Technology Data Exchange (ETDEWEB)

Brites-Nóbrega, Fernanda F. de [Chemical Engineering Department, Universidade Estadual de Maringá (UEM), Av. Colombo, 5790, CEP 87020-900 Maringá, PR (Brazil); Sanitary and Environmental Engineering Department, Universidade Federal de Minas Gerais (UFMG), Av. Antônio Carlos, 6627, Campus Pampulha, Belo Horizonte, MG (Brazil); Polo, Aldino N.B.; Benedetti, Angélica M. [Chemical Engineering Department, Universidade Estadual do Oeste do Paraná (UNIOESTE), Rua da Faculdade, 645, CEP 85903-000 Toledo, PR (Brazil); Leão, Mônica M.D. [Sanitary and Environmental Engineering Department, Universidade Federal de Minas Gerais (UFMG), Av. Antônio Carlos, 6627, Campus Pampulha, Belo Horizonte, MG (Brazil); Slusarski-Santana, Veronice, E-mail: veronice.santana@unioeste.br [Chemical Engineering Department, Universidade Estadual do Oeste do Paraná (UNIOESTE), Rua da Faculdade, 645, CEP 85903-000 Toledo, PR (Brazil); Fernandes-Machado, Nádia R.C. [Chemical Engineering Department, Universidade Estadual de Maringá (UEM), Av. Colombo, 5790, CEP 87020-900 Maringá, PR (Brazil)

2013-12-15

Highlights: • The synergic effect between ZnO and NaX was positive, which increased its activity. • The best results were obtained at pH 3 and 9 with ZnO/NaX and at pH 3 with Nb{sub 2}O{sub 5}/AC. • High degradation and considerable mineralization were attained with 10% ZnO/NaX. • ZnO and Nb{sub 2}O{sub 5} supported on NaX and AC are promising alternatives as photocatalysts. -- Abstract: This study aimed to evaluate the photocatalytic activity of ZnO and Nb{sub 2}O{sub 5} catalysts, both supported on NaX zeolite and activated charcoal (AC). The synergistic effect between oxide and support and the influence of solution pH (3, 7 and 9) on photocatalytic degradation of reactive blue 5G (C.I. 222) were analyzed. The catalysts Nb{sub 2}O{sub 5}/NaX, Nb{sub 2}O{sub 5}/AC and ZnO/NaX, ZnO/AC with 5 and 10% (wt%) were prepared by wet impregnation. The results showed that the catalysts exhibit quite different structural and textural properties. The synergic effect between ZnO and NaX support was higher than that with the activated charcoal, showing that these catalysts were more efficient. The most photoactive catalyst was 10% ZnO/NaX which showed 100% discoloration of the dye solution at pH 3, 7 and 9 after 0.5, 5 and 2 h of irradiation, respectively. The hydrolytic nature of zeolite favored the formation of surface hydroxyl radicals, which increased the activity of the photocatalyst. Thus, catalysts supported on NaX zeolite are promising for use in photocatalysis.

The influence of rhodium burn-up on the sensitivity of rhodium self-powered neutron detectors

International Nuclear Information System (INIS)

Erben, O.

1980-01-01

Depression and self-shielding coefficients are presented for thermal and epithermal neutron flux densities. Functions are shown describing the distribution of beta particle sources on the emitter cross section for 0 to 50% rhodium burnup. The values are calculated of detector sensitivity to thermal and epithermal neutron flux densities for the said burnup for main types of rhodium SPN detectors made by SODERN. (J.B.)

Platinum, palladium, and rhodium in volcanic and plutonic rocks from the Gravina-Nutzotin belt, Alaska

Science.gov (United States)

Page, Norman J; Berg, Henry C.; Haffty, Joseph

1977-01-01

The Gravina-Nutzotin belt of Middle (?) Jurassic to middle Cretaceous sedimentary and volcanic rocks in south and southeastern Alaska includes concentrically zoned ultramafic complexes known to contain platinum-group metals. Previous isotopic, petrologic, and geologic studies suggested a close relation in time and space between the volcanic rocks and the ultramafic complexes. Interpretation of 40 analyses for platinum, palladium, and rhodium in volcanic and plutonic rocks of the belt indicates a strong geochemical correlation between the two groups of rocks and is in support of their being cogenetic either from directly connected magma chambers and flows or indirectly by selective concentration processes from similar mantle material.

Copper(II)–imida‐salen Complexes Encapsulated into NaY Zeolite for Oxidations Reactions

DEFF Research Database (Denmark)

Kuźniarska‐Biernacka, Iwona; Carvalho, M. Alice; Rasmussen, Søren Birk

2013-01-01

The oxidation of phenol, cychohexanol and hydroquinone has been screened in the presence of copper(II) complexes with the Schiff‐base salen ligand, 1,5‐bis[(E)‐5‐chloro‐2‐hydroxybenzylideneamino]‐1H‐imidazole‐4‐carbonitrile, and encapsulated into NaY zeolite by using two different methods. The new...

Labeling of human serum albumin with 105Rh-cysteine complexes

International Nuclear Information System (INIS)

Lo, J.M.; Pillai, M.R.A.; John, C.S.; Troutner, D.E.

1990-01-01

The conjugation of a complex formed by reacting RhCl 3 with cysteine to human serum albumin has been investigated. Approximately 50% of the rhodium (labelled with 105 Rh) was converted to the complex. Conjugation of the complex to HSA via the ECDI method resulted in yields of ∼ 40% of the total rhodium or ∼ 80% of the Rh-cysteine complex. No conjugation was observed in the absence of the ECDI. At approximately equal molar concentrations of rhodium and HSA, an average of ∼ 0.4 rhodium atoms per HSA molecule was achieved. (author)

Molecular recognition in protein modification with rhodium metallopeptides

Science.gov (United States)

Ball, Zachary T.

2015-01-01

Chemical manipulation of natural, unengineered proteins is a daunting challenge which tests the limits of reaction design. By combining transition-metal or other catalysts with molecular recognition ideas, it is possible to achieve site-selective protein reactivity without the need for engineered recognition sequences or reactive sites. Some recent examples in this area have used ruthenium photocatalysis, pyridine organocatalysis, and rhodium(II) metallocarbene catalysis, indicating that the fundamental ideas provide opportunities for using diverse reactivity on complex protein substrates and in complex cell-like environments. PMID:25588960

Ru complexes of Hoveyda–Grubbs type immobilized on lamellar zeolites: activity in olefin metathesis reactions

Czech Academy of Sciences Publication Activity Database

Balcar, Hynek; Žilková, Naděžda; Kubů, Martin; Mazur, Michal; Bastl, Zdeněk; Čejka, Jiří

2015-01-01

Roč. 11, NOV 2015 (2015), s. 2087-2096 ISSN 1860-5397 Institutional support: RVO:61388955 Keywords : Hoveyda-Grubbs type catalyst * hybrid catalysts * lamellar zeolites Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.697, year: 2015

Measurement of the hyperfine magnetic field on rhodium in chromium

International Nuclear Information System (INIS)

Peretto, P.; Teisseron, G.; Berthier, J.

1978-01-01

Hyperfine magnetic field of rhodium in a chromium matrix is studied. Anisotropy of rhodium 100 is + 0.17. Time dependence of angular correlation is given with a sample containing 145 ppm of rhodium despite the short life [fr

STABLE SILICA-GRAFTED POLYMER-BOUND BULKY-PHOSPHITE MODIFIED RHODIUM HYDROFORMYLATION CATALYSTS

NARCIS (Netherlands)

JONGSMA, T; VANAERT, H; FOSSEN, M; CHALLA, G; VANLEEUWEN, PWNM

1993-01-01

The present study demonstrates that silica-grafted polymer-bound phosphite modified rhodium complexes can be used in continuous flow reactors. The hydroformylation of styrene was carried out at moderate pressure (p(CO/H-2) = 30 bar) and temperature (T = 100-degrees-C), yielding constant conversions

Zeolite-Y entrapped Ru(III and Fe(III complexes as heterogeneous catalysts for catalytic oxidation of cyclohexane reaction

Directory of Open Access Journals (Sweden)

Chetan K. Modi

2017-02-01

Full Text Available Catalysis is probably one of the greatest contributions of chemistry to both economic growth and environmental protection. Herein we report the catalytic behavior of zeolite-Y entrapped Ru(III and Fe(III complexes with general formulae [M(VTCH2·2H2O]+-Y and [M(VFCH2·2H2O]+-Y [where, VTCH = vanillin thiophene-2-carboxylic hydrazone and VFCH = vanillin furoic-2-carboxylic hydrazone] over the oxidation of cyclohexane forming cyclohexanone and cyclohexanol. The samples were corroborated by various physico-chemical techniques. These zeolite-Y based complexes are stable and recyclable under current reaction conditions. Amongst them, [Ru(VTCH2⋅2H2O]+-Y showed higher catalytic activity (41.1% with cyclohexanone (84.6% selectivity.

Synthesis and crystal structure of the rhodium(I) cyclooctadiene complex with bis(3-tert-butylimidazol-2-ylidene)borate ligand

Energy Technology Data Exchange (ETDEWEB)

Chen, F.; Shao, K.-J.; Xiao, Y.-C.; Pu, X.-J.; Zhu, B., E-mail: zhubao-999@126.com [Affiliated Wuxi Peoples Hospital, Department of Nuclear Medicine, Nanjing Medical University (China); Jiang, M.-J., E-mail: jmj16888@126.com [Affiliated Wuxi Peoples Hospital, Department of Clinical Laboratory Science, Nanjing Medical University (China)

2015-12-15

The rhodium(I) cyclooctadiene complex with the bis(3-tert-butylimidazol-2-ylidene)borate ligand [H{sub 2}B(Im{sup t}Bu){sup 2}]Rh(COD) C{sup 22}H{sup 36}BN{sup 4}Rh, has been prepared, and its crystal structure is determined by X-ray diffraction. Complex exhibits slightly distorted square planar configurations around the metal center, which is coordinated by the bidentate H{sup 2}B(Im{sup t}Bu){sub 2} and one cyclooctadiene group. The Rh–C{sub carbene} bond lengths are 2.043(4) and 2.074(4) Å, and the bond angle C–Rh1–C is 82.59°. The dihedral angle between two imidazol-2-ylidene rings is 67.30°.

Asymmetric Synthesis of Hydrocarbazoles Catalyzed by an Octahedral Chiral-at-Rhodium Lewis Acid.

Science.gov (United States)

Huang, Yong; Song, Liangliang; Gong, Lei; Meggers, Eric

2015-12-01

A bis-cyclometalated chiral-at-metal rhodium complex catalyzes the Diels-Alder reaction between N-Boc-protected 3-vinylindoles (Boc = tert-butyloxycarbonyl) and β-carboxylic ester-substituted α,β-unsaturated 2-acyl imidazoles with good-to-excellent regioselectivity (up to 99:1) and excellent diastereoselectivity (>50:1 d.r.) as well as enantioselectivity (92-99% ee) under optimized conditions. The rhodium catalyst serves as a chiral Lewis acid to activate the 2-acyl imidazole dienophile by two-point binding and overrules the preferred regioselectivity of the uncatalyzed reaction. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Rhodium(I)-Complexes Catalyzed 1,4-Conjugate Addition of Arylzinc Chlorides to N-Boc-4-pyridone.

Science.gov (United States)

Guo, Fenghai; McGilvary, Matthew A; Jeffries, Malcolm C; Graves, Briana N; Graham, Shekinah A; Wu, Yuelin

2017-05-01

Rhodium(I)-complexes catalyzed the 1,4-conjugate addition of arylzinc chlorides to N -Boc-4-pyridone in the presence of chlorotrimethylsilane (TMSCl). A combination of [RhCl(C₂H₄)₂]₂ and BINAP was determined to be the most effective catalyst to promote the 1,4-conjugate addition reactions of arylzinc chlorides to N -Boc-4-pyridone. A broad scope of arylzinc reagents with both electron-withdrawing and electron-donating substituents on the aromatic ring successfully underwent 1,4-conjugate addition to N -Boc-4-pyridone to afford versatile 1,4-adducts 2-substituted-2,3-dihydropyridones in good to excellent yields (up to 91%) and excellent ee (up to 96%) when ( S )-BINAP was used as chiral ligand.

Komplexe zouten van trans-1-2-diaminocyclohexaan met driewaardig rhodium en kobalt

NARCIS (Netherlands)

Bijkerk, Lucas

1937-01-01

Some complex salts of trans-I-2-díominocyclohexane with trivalent cobaltum and rhodium were prepared and their properties described in detail. Diaminocyclohexanwe as obtained by the following series of reactions: cyclohexanone --> cyclohexanone-I-oxalylicester --> cyclohexonone-I-carboxylicester-2

Zeolite-encapsulated Co(II), Mn(II), Cu(II) and Cr(III) salen complexes as catalysts for efficient selective oxidation of benzyl alcohol

Science.gov (United States)

Li, F. H.; Bi, H.; Huang, D. X.; Zhang, M.; Song, Y. B.

2018-01-01

Co(II), Mn(II), Cu(II) and Cr(III) salen type complexes were synthesized in situ in Y zeolite by the reaction of ion-exchanged metal ions with the flexible ligand molecules that had diffused into the cavities. Data of characterization indicates the formation of metal salen complexes in the pores without affecting the zeolite framework structure, the absence of any extraneous species and the geometry of encapsulated complexes. The catalytic activity results show that Cosalcyen Y exhibited higher catalytic activity in the water phase selective oxidation of benzyl alcohol, which could be attributed to their geometry and the steric environment of the metal actives sites.

Light alkane (mixed feed selective dehydrogenation using bi-metallic zeolite supported catalyst

Directory of Open Access Journals (Sweden)

Zeeshan Nawaz

2009-12-01

Full Text Available Light alkanes are the important intermediates of many refinery processes and their catalytic dehydrogenation gives corresponding alkenes. The aim behind this experimentation is to investigate reaction behavior of mixed alkanes during direct catalytic dehydrogenation and emphasis has been given to enhance propene. Bi-metallic zeolite supported catalyst Pt-Sn/ZSM-5 was prepared by sequentional impregnation method and characterized by BET, EDS and XRD. Direct dehydrogenation reaction is highly endothermic and its conversion is thermodynamically limited. Results showed that the increase in temperature increases the conversion to some extent but there is no overall effect on selectivity of propene. Increase in time-on-stream (TOS remarkably improves propene selectivity at the expense of lower conversion. The performances of bi-metallic zeolite based catalyst largely affected by coke deposition. The presence of butane and ethane adversely affected propane conversion. Optimum propene selectivity is about 48 %, obtained at 600 oC and time-on-stream 10 h.

Extraction of ruthenium thiocyanate and its separation from rhodium by polyurethane foam

International Nuclear Information System (INIS)

Al-Bazi, S.J.; Chow, A.

1984-01-01

Conditions for the formation and extraction of the thiocyanate complex of ruthenium are reported. Distribution coefficients of more than 10 4 and a capacity of about 0.24 mole per kg of foam were obtained. The effect of the chloride salts of various univalent cations on the extraction of Ru(SCN) 6 3- indicated that the efficiency of ruthenium extraction depends on how well the cation fits into the polyether segment of the polyurethane foam, which agrees with the 'cation-chelation' mechanism. The separation of ruthenium and rhodium indicated that more than 95% of the rhodium remained in the aqueous phase and about 95% of the ruthenium was retained by the polyurethane foam and could be easily recovered. (author)

Energetics of sodium-calcium exchanged zeolite A.

Science.gov (United States)

Sun, H; Wu, D; Guo, X; Shen, B; Navrotsky, A

2015-05-07

A series of calcium-exchanged zeolite A samples with different degrees of exchange were prepared. They were characterized by powder X-ray diffraction (XRD) and differential scanning calorimetry (DSC). High temperature oxide melt drop solution calorimetry measured the formation enthalpies of hydrated zeolites CaNa-A from constituent oxides. The water content is a linear function of the degree of exchange, ranging from 20.54% for Na-A to 23.77% for 97.9% CaNa-A. The enthalpies of formation (from oxides) at 25 °C are -74.50 ± 1.21 kJ mol(-1) TO2 for hydrated zeolite Na-A and -30.79 ± 1.64 kJ mol(-1) TO2 for hydrated zeolite 97.9% CaNa-A. Dehydration enthalpies obtained from differential scanning calorimetry are 32.0 kJ mol(-1) H2O for hydrated zeolite Na-A and 20.5 kJ mol(-1) H2O for hydrated zeolite 97.9% CaNa-A. Enthalpies of formation of Ca-exchanged zeolites A are less exothermic than for zeolite Na-A. A linear relationship between the formation enthalpy and the extent of calcium substitution was observed. The energetic effect of Ca-exchange on zeolite A is discussed with an emphasis on the complex interactions between the zeolite framework, cations, and water.

Complexes of rhodium (I) and iridium (I) with mixed phosphorus-oxygen and phosphorus-nitrogen glands

International Nuclear Information System (INIS)

Meintjies, E.; Singleton, E.; Schmutzler, R.; Sell, M.

1985-01-01

A series of four- and five-coordinate rhodium(I) and iridium(I) complexes of the type [MCl(cod)L] and [M(COD)L 2 ] sup(+)[M = Rh or Ir;cod = cycloocta-1,5-diene; L = P(C 6 H 4 OMe-o) 3 ,PMe 2 (C 6 H 4 OMe-o), PPh 2 (C 6 H 4 OMe-o),PPh 2 -(C 6 H 4 NMe 2 -o),PMe(C 6 H 4 OMe-o) 2 and PPh 2 (C 6 H 4 OPr sup(i)-o)] have been prepared from the reactions of [(MCl(cod)) 2 ] (M = Rh or Ir) with the appropriate stoichiometric amount of L in diethyl ether or methanol solution. N.m.r. evidence ( 1 H and 13 C) is presented for non-chelation in the case of the ether ligands and chelation for the amine ligand. Thus, the complexes [MCl(cod)L](L = ether ligand) are mononuclear square-planar species, whereas the amine ligand chelates to the metal atom, and a distorted trigonal bipyramidal structure is proposed. Attempts at displacing cod from the complexes [MCl(cod)L] with these ether and amine ligands, or with small phosphines, were unsuccessful. However, treatment of [MCl(cod)[P(C 6 H 4 OMe-o) 3

Kinetic method of determination of rhodium trace amounts

International Nuclear Information System (INIS)

Kalinina, V.E.; Lyakushina, V.M.; Rybina, A.E.

1978-01-01

A catalytic action of rhodium compounds has been detected and studied in the reaction of copper (2) tellurate oxidation with hypobromite to ditelluratocuprate (3) in an alkaline medium. The relationships between the reaction rate and concentrations of copper, tellurate, and hypobromite have been established. The optimum concentrations of the used compounds have been found: Csub(Cu(2))=4x10 -5 g-ion/l; Csub(OHsup(-))=3.0 g-ion/l; Csub(Te)=1.4x10 -2 g-ion/l; Csub(NaBrO)=2.17x10 -3 M. It has been established for chloride, sulphate, and perchlorate solutions of rhodium (3) and (4) that the reaction sensitivity increases by 2-3-fold with a temperature rise from 25-60 deg C. The technique of determining rhodium traces has been developed based on its catalytic action. The low limit of determined rhodium amounts is about 10 -3 mkg/ml

Rhodium enalcarbenoids: direct synthesis of indoles by rhodium(II)-catalyzed [4+2] benzannulation of pyrroles.

Science.gov (United States)

Dawande, Sudam Ganpat; Kanchupalli, Vinaykumar; Kalepu, Jagadeesh; Chennamsetti, Haribabu; Lad, Bapurao Sudam; Katukojvala, Sreenivas

2014-04-14

Disclosed herein is the design of an unprecedented electrophilic rhodium enalcarbenoid which results from rhodium(II)-catalyzed decomposition of a new class of enaldiazo compounds. The synthetic utility of these enalcarbenoids has been successfully demonstrated in the first transition-metal-catalyzed [4+2] benzannulation of pyrroles, thus leading to substituted indoles. The new benzannulation has been applied to the efficient synthesis of the natural product leiocarpone as well as a potent adipocyte fatty-acid binding protein inhibitor. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Initial Stages in the Rhodium(III)-Catalyzed C-H Bond Activation of Primary Alcohols in Aqueous Solution

DEFF Research Database (Denmark)

Eriksen, J.; Monsted, L.; Monsted, O.

2010-01-01

The mechanism of the catalytic HID exchange in primary alcohol substrates derived from aldopentoses, promoted by a macrocyclic rhodium(III) complex, has been shown to occur by a reversible redox reaction that gives aldehyde and a rhodium hydride complex. Hydride exchange in the latter complex...... promotes the introduction of solvent hydrogen in the primary alcohol formed by the reverse reaction. The hydride complex has been crystallographically characterized as a trifluoromethanesulfonate salt that contains the trans-[Rh(cycb)(H)(OH2)](2+) (cycb = rac-5,5,7,12,12,14-hexamethyl-1......,4,8,11-tetraazacyclotetradecane) cation. The hydride complex is stable for extended periods of time in acidic solution in the absence of oxidants. In basic solutions a series of base-catalyzed reactions take place to yield ultimately the same mixture of [Rh(cycb)(OH)(2)](+) isomers as produced by base hydrolysis of the trans...

The effects of primary beam filters on the analysis of rhodium and cadmium using a rhodium target x-ray tube

International Nuclear Information System (INIS)

Anzelmo, J.A.; Boyer, B.W.

1986-01-01

Since its introduction in 1964, the thin end-window rhodium target x-ray tube has been considered to be an excellent general purpose source of excitation. Heavy elements are efficiently excited by high Bremsstrahlung and the K lines of rhodium while the light elements are excited by the L lines of rhodium. The ability to efficiently excite both heavy and light elements is essential to special applications such as auto catalysts, which are composed of precious metals in a clay-like matrix. Close control of the light elements, including sodium, phosphorous, aluminum and silicon, and the heavy element precious metals, such as rhodium, are necessary to keep operating characteristics and manufacturing expense at desired levels. A quick survey of typical x-ray tube targets shows that some targets are more efficient for light elements while others are more efficient for heavy elements. The few general purpose x-ray tubes that are available have characteristic lines which overlap on elements to be determined. The rhodium target, which is a good excitation source for most of the elements mentioned, contains line overlaps on cadmium (RHKB) and rhodium (RHKA). When using a sequential wavelength dispersive XRF spectrometer, the characteristic lines of the tube scattered from the sample can be removed by a programmable primary beam filter having an absorption edge just higher in wavelength than the wavelengths to be removed. The thickness and composition of the filter, as well as the choice of KV and MA, will determine the operating parameter necessary to achieve the optimum precision and lowest limits of detection. For this study, synthetic samples are made up using Kaolin as the matrix

Processing of radioactive waste solution with zeolites. I. Thermal transformation of Na, Cs and Sr type zeolites

Energy Technology Data Exchange (ETDEWEB)

Kanno, T; Mimura, H; Kitamura, T [Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy

1976-08-01

Thermal transformation of Na, Cs and Sr type zeolites were studied by means of differential thermal analysis (DTA), thermogravimetric analysis (TGA) and X-ray powder diffraction. Synthetic zeolites A, X and Y, synthetic mordenite (Zeolon) and natural mordenite were used in this study. Na type zeolites of A and X recrystallized to Nepheline (NaAlSiO/sub 4/) above 1,000/sup 0/C, but the structures of zeolite Y and mordenite collapsed above about 900/sup 0/C and did not recrystallize until 1,200/sup 0/C. Cs type zeolites of A and X recrystallized to pollucite (CsAlSi/sub 2/O/sub 6/) above 1,000/sup 0/C and Cs type of zeolite Y recrystallized to it above 1,100/sup 0/C, but the structure of mordenite collapsed above 1,000/sup 0/C and did not recrystallize until 1,200/sup 0/C. On Sr type zeolites, zeolite A and X recrystallized to strontium aluminosilicate (SrAl/sub 2/Si/sub 2/O/sub 8/) above 1,100/sup 0/C and zeolite Y recrystallized to it above 1,200/sup 0/C, but the structure of mordenite collapsed above 1,000/sup 0/C. The results described above were supported by microscopic observation and the measurement of density. If this solidifications by calcination of zeolites are further studied, new informations concerning the fixation of Cs and Sr will be obtained.

Electronic and magnetic properties of ultrathin rhodium nanowires

CERN Document Server

Wang Bao Lin; Ren-Yun; Sun Hou Qian; Chen Xiao Shuang; Zhao Ji Jun

2003-01-01

The structures of ultrathin rhodium nanowires are studied using empirical molecular dynamics simulations with a genetic algorithm. Helical multishell cylindrical and pentagonal packing structures are found. The electronic and magnetic properties of the rhodium nanowires are calculated using an spd tight-binding Hamiltonian in the unrestricted Hartree-Fock approximation. The average magnetic moment and electronic density of states are obtained. Our results indicate that the electronic and magnetic properties of the rhodium nanowires depend not only on the size of the wire but also on the atomic structure. In particular, centred pentagonal and hexagonal structures can be unusually ferromagnetic.

Rhodium Catalyzed Decarbonylation

DEFF Research Database (Denmark)

Garcia Suárez, Eduardo José; Kahr, Klara; Riisager, Anders

2017-01-01

Rhodium catalyzed decarbonylation has developed significantly over the last 50 years and resulted in a wide range of reported catalyst systems and reaction protocols. Besides experimental data, literature also includes mechanistic studies incorporating Hammett methods, analysis of kinetic isotope...

Zeolitic materials with hierarchical porous structures.

Science.gov (United States)

Lopez-Orozco, Sofia; Inayat, Amer; Schwab, Andreas; Selvam, Thangaraj; Schwieger, Wilhelm

2011-06-17

During the past several years, different kinds of hierarchical structured zeolitic materials have been synthesized due to their highly attractive properties, such as superior mass/heat transfer characteristics, lower restriction of the diffusion of reactants in the mesopores, and low pressure drop. Our contribution provides general information regarding types and preparation methods of hierarchical zeolitic materials and their relative advantages and disadvantages. Thereafter, recent advances in the preparation and characterization of hierarchical zeolitic structures within the crystallites by post-synthetic treatment methods, such as dealumination or desilication; and structured devices by in situ and ex situ zeolite coatings on open-cellular ceramic foams as (non-reactive as well as reactive) supports are highlighted. Specific advantages of using hierarchical zeolitic catalysts/structures in selected catalytic reactions, such as benzene to phenol (BTOP) and methanol to olefins (MTO) are presented. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Epitaxially Grown Layered MFI–Bulk MFI Hybrid Zeolitic Materials

KAUST Repository

Kim, Wun-gwi; Zhang, Xueyi; Lee, Jong Suk; Tsapatsis, Michael; Nair, Sankar

2012-01-01

The synthesis of hybrid zeolitic materials with complex micropore-mesopore structures and morphologies is an expanding area of recent interest for a number of applications. Here we report a new type of hybrid zeolite material, composed of a layered

Selective Cytotoxicity of Rhodium Metalloinsertors in Mismatch Repair-Deficient Cells†

Science.gov (United States)

Ernst, Russell J.; Komor, Alexis C.; Barton, Jacqueline K.

2011-01-01

Mismatches in DNA occur naturally during replication and as a result of endogenous DNA damaging agents, but the mismatch repair (MMR) pathway acts to correct mismatches before subsequent rounds of replication. Rhodium metalloinsertors bind to DNA mismatches with high affinity and specificity and represent a promising strategy to target mismatches in cells. Here we examine the biological fate of rhodium metalloinsertors bearing dipyridylamine ancillary ligands in cells deficient in MMR versus those that are MMR-proficient. These complexes are shown to exhibit accelerated cellular uptake which permits the observation of various cellular responses, including disruption of the cell cycle, monitored by flow cytometry assays, and induction of necrosis, monitored by dye exclusion and caspase inhibition assays, that occur preferentially in the MMR-deficient cell line. These cellular responses provide insight into the mechanisms underlying the selective activity of this novel class of targeted anti-cancer agents. PMID:22103240

Quantification of Rhodium in a Series of Inorganic and ...

African Journals Online (AJOL)

NICO

... such as rhodium hydridocarbonyl tristriphenylphosphine, [HRh(CO)(PPh3)3], .... The selection of the most suitable wavelengths for rhodium, yttrium and cobalt ... chloride ions were removed from the CRM samples as chlorine gas with the ...

Inhibition of palm oil oxidation by zeolite nanocrystals.

Science.gov (United States)

Tan, Kok-Hou; Awala, Hussein; Mukti, Rino R; Wong, Ka-Lun; Rigaud, Baptiste; Ling, Tau Chuan; Aleksandrov, Hristiyan A; Koleva, Iskra Z; Vayssilov, Georgi N; Mintova, Svetlana; Ng, Eng-Poh

2015-05-13

The efficiency of zeolite X nanocrystals (FAU-type framework structure) containing different extra-framework cations (Li(+), Na(+), K(+), and Ca(2+)) in slowing the thermal oxidation of palm oil is reported. The oxidation study of palm oil is conducted in the presence of zeolite nanocrystals (0.5 wt %) at 150 °C. Several characterization techniques such as visual analysis, colorimetry, rheometry, total acid number (TAN), FT-IR spectroscopy, (1)H NMR spectroscopy, and Karl Fischer analyses are applied to follow the oxidative evolution of the oil. It was found that zeolite nanocrystals decelerate the oxidation of palm oil through stabilization of hydroperoxides, which are the primary oxidation product, and concurrently via adsorption of the secondary oxidation products (alcohols, aldehydes, ketones, carboxylic acids, and esters). In addition to the experimental results, periodic density functional theory (DFT) calculations are performed to elucidate further the oxidation process of the palm oil in the presence of zeolite nanocrystals. The DFT calculations show that the metal complexes formed with peroxides are more stable than the complexes with alkenes with the same ions. The peroxides captured in the zeolite X nanocrystals consequently decelerate further oxidation toward formation of acids. Unlike the monovalent alkali metal cations in the zeolite X nanocrystals (K(+), Na(+), and Li(+)), Ca(2+) reduced the acidity of the oil by neutralizing the acidic carboxylate compounds to COO(-)(Ca(2+))1/2 species.

Zeolite-zeolite composite composed of Y zeolite and single-crystal-like ZSM-5 zeolite: Fabricated by a process like “big fish swallowing little one”

Energy Technology Data Exchange (ETDEWEB)

Pan, Meng; Li, Peng [Research Centre of Energy Chemical & Catalytic Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Zheng, Jiajun, E-mail: zhengjiajun@tyut.edu.cn [Research Centre of Energy Chemical & Catalytic Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Liu, Yujian [SINOPEC Research Institute of Petroleum Processing, Beijing, 100083 (China); Kong, Qinglan [Research Centre of Energy Chemical & Catalytic Technology, Taiyuan University of Technology, Taiyuan 030024 (China); Tian, Huiping [SINOPEC Research Institute of Petroleum Processing, Beijing, 100083 (China); Li, Ruifeng, E-mail: rfli@tyut.edu.cn [Research Centre of Energy Chemical & Catalytic Technology, Taiyuan University of Technology, Taiyuan 030024 (China)

2017-06-15

Zeolite-zeolite composite composed of Y and ZSM-5 zeolite was prepared using depolymerized Y as partial nutrients for the growth of ZSM-5. The as-synthesized samples were characterized by X-ray powder diffraction (XRD), FT-IR, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), N{sub 2} adsorption-desorption measurement and Thermogravimetric analysis (TG). Chemical equilibrium at the solution-crystal interface was changed because of the partially depolymerized Y zeolite, the conditions necessary for the growth of ZSM-5 were therefore obtained. ZSM-5 zeolite crystals nucleated and grew on the interface, and Y zeolite crystals were then gradually swallowed by the growing single-crystal-like ZSM-5. - Graphical abstract: Y zeolite crystals in the hydrothermal system were partially depolymerized and an ambience in favor of the formation of ZSM-5 was formed, and ZSM-5 zeolite crystals nucleated and grew up on the external surfaces of Y zeolite crystals. As a consequence, Y zeolite crystals were swallowed by single-crystal-like ZSM-5. - Highlights: • Zeolite composite is composed by Y zeolite and single-crystal-like ZSM-5. • A composite material formed by a process like “big fish swallowing little one”. • Ratio of two zeolites in the as-synthesized sample can be adjusted.

INTERKALASI XILENOL ORANGE PADA ZEOLIT ALAM LAMPUNG SEBAGAI ELEKTRODA ZEOLIT TERMODIFIKASI

Directory of Open Access Journals (Sweden)

Fitriyah Fitriyah

2016-07-01

Full Text Available Zeolit terbagi menjadi zeolit alam dan zeolit sintesis, kapasitas adsorpsi zeolit alam umumnya lebih rendah daripada zeolit sintesis, sehingga untuk meningkatkan kapasitas adsorpsinya, karakter permukaan zeolit alam perlu diubah dengan melakukan proses modifikasi permukaan melalui berbagai metode, salah satunya dengan metode interkalasi. Tujuan penelitian ini yaitu menginterkalasi zat warna xilenol orange ke dalam zeolit alam Lampung dan mengaplikasikannya sebagai elektroda zeolit termodifikasi. Melalui proses interkalasi diharapkan dapat meningkatkan kegunaan dan nilai tambah dari zeolit. Data hasil penelitian menunjukkan bahwa xilenol orange (XO dapat diinterkalasikan ke dalam zeolit, hal ini dapat dilihat dari pita spektrum FTIR yang memiliki serapan pada bilangan gelombang 1383 cm-1, yaitu menunjukkan serapan dari S=O simetris dan asimetris pada gugus –SO3H,hal ini diduga karena XO memiliki gugus SO3 sehingga menyebabkan adanya serangan pada proton zeolit. Berdasarkan penelitian dapat disarikan bahwa xilanol orange dapat terinterkalasi pada zeolit alam Lampung dan dapat dimanfaatkan sebagai elektroda pendeteksi logam.

An Extended X-ray Absorption Fine Structure Study of Rhodium-Oxygen Bonds in a Highly Dispersed Rhodium/Aluminum Oxide Catalyst

NARCIS (Netherlands)

Koningsberger, D.C.; Zon, J.B.A.D. van; Blik, H.F.J. van 't; Visser, G.J.; Prins, R.; Mansour, A.N.; Sayers, D.E.; Short, D.R.

1985-01-01

Analysis of in situ EXAFS measurements on a 2.4 wt % Rh/A120, catalyst, reduced at 473 K after calcination at 623 K, shows the presence of two different rhodium-oxygen bonds (viz. 2.05 and 2.68 A). The oxygen neighbors of rhodium at a distance of 2.05 A disappear after reduction at 673 K. The

Ion flotation of rhodium(III) and palladium(II) with anionic surfactants.

Science.gov (United States)

He, X C

1991-03-01

The ion flotation of rhodium(III) and palladium(II) with some anionic surfactants has been investigated. Two flotation procedures are proposed for the separation of some platinum metals, based on differences in the kinetic properties of the chloro-complexes of rhodium(III), palladium(II) and platinum(IV). The first involves the selective flotation of Rh(H(2)O)(3+)(6) from PdCl(2-)(4) and PtCl(2-)(6) in dilute hydrochloric acid with sodium dodecylbenzenesulfonate (SDBS). After precipitation of the hydroxide and redissolution in dilute acid, the Rh(III) is converted into Rh(H(2)O)(3+)(6), Pd(II) and Pt(IV) remaining as PdCl(2-)(4) and PtCl(2-)(6) respectively, and separation is achieved by floating the Rh(H(2)O)(3+)(6) with SDBS. The second is for separation of Pd(II). Prior to flotation, the solution of PdCl(2-)(4) and PtCl(2-)(6) is heated with ammonium acetate to convert PdCl(2-)(4) into Pd(NH(3))(2+)(4). The chloro-complex of Pt(IV) is unaffected. The complex cation, Pd(NH(3))(2+)(4), is then selectively floated with SDBS. The procedures are fast, simple and do not require expensive reagents and apparatus.

Chemo- and regioselective homogeneous rhodium-catalyzed hydroamidomethylation of terminal alkenes to N-alkylamides.

Science.gov (United States)

Raoufmoghaddam, Saeed; Drent, Eite; Bouwman, Elisabeth

2013-09-01

A rhodium/xantphos homogeneous catalyst system has been developed for direct chemo- and regioselective mono-N-alkylation of primary amides with 1-alkenes and syngas through catalytic hydroamidomethylation with 1-pentene and acetamide as model substrates. For appropriate catalyst performance, it appears to be essential that catalytic amounts of a strong acid promoter, such as p-toluenesulfonic acid (HOTs), as well as larger amounts of a weakly acidic protic promoter, particularly hexafluoroisopropyl alcohol (HOR(F) ) are applied. Apart from the product N-1-hexylacetamide, the isomeric unsaturated intermediates, hexanol and higher mass byproducts, as well as the corresponding isomeric branched products, can be formed. Under optimized conditions, almost full alkene conversion can be achieved with more than 80% selectivity to the product N-1-hexylamide. Interestingly, in the presence of a relatively high concentration of HOR(F) , the same catalyst system shows a remarkably high selectivity for the formation of hexanol from 1-pentene with syngas, thus presenting a unique example of a selective rhodium-catalyzed hydroformylation-hydrogenation tandem reaction under mild conditions. Time-dependent product formation during hydroamidomethylation batch experiments provides evidence for aldehyde and unsaturated intermediates; this clearly indicates the three-step hydroformylation/condensation/hydrogenation reaction sequence that takes place in hydroamidomethylation. One likely role of the weakly acidic protic promoter, HOR(F) , in combination with the strong acid HOTs, is to establish a dual-functionality rhodium catalyst system comprised of a neutral rhodium(I) hydroformylation catalyst species and a cationic rhodium(III) complex capable of selectively reducing the imide and/or ene-amide intermediates that are in a dynamic, acid-catalyzed condensation equilibrium with the aldehyde and amide in a syngas environment. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Zeolite studies. Aluminium phosphate zeolites

Energy Technology Data Exchange (ETDEWEB)

Haegh, G.S.; Blindheim, U.

1983-12-01

Alpo-zeolites (ALPO4-zeolites) have been synthesized by hydrothermal synthesis in an autoclave from alumina, tetralkylammonium hydroxide and phosphorus acid. Catalysis tests with hydrocarbons indicate that the compounds have good olefinisomerization activity and selectivity.

TPR investigations on the reducibility of Cu supported on Al2O3, zeolite Y and SAPO-5

International Nuclear Information System (INIS)

Hoang, Dang Lanh; Dang, Thi Thuy Hanh; Engeldinger, Jana; Schneider, Matthias; Radnik, Joerg; Richter, Manfred; Martin, Andreas

2011-01-01

Reducibility of Cu supported on Al 2 O 3 , zeolite Y and silicoaluminophosphate SAPO-5 has been investigated in dependence on the Cu content using a method combining conventional temperature programmed reduction (TPR) by hydrogen with reoxidation in N 2 O followed by a second the so-called surface-TPR (s-TPR). The method enables discrimination and a quantitative estimation of the Cu oxidation states +2, +1 and 0. The quantitative results show that the initial oxidation state of Cu after calcination in air at 400 deg. C, independent on the nature of the support, is predominantly +2. Cu 2+ supported on Al 2 O 3 is quantitatively reduced by hydrogen to metallic Cu 0 . Comparing the TPR of the samples calcined in air and that of samples additionally pre-treated in argon reveals that in zeolite Y and SAPO-5 Cu 2+ cations are stabilized as weakly and strongly forms. In both systems, strongly stabilized Cu 2+ ions are not auto-reduced by pre-treatment in argon at 650 deg. C, but are reduced in hydrogen to form Cu + . The weakly stabilized Cu 2+ ions, in contrast, may be auto-reduced by pre-treatment in argon at 650 deg. C forming Cu + but are reduced in hydrogen to metallic Cu 0 . - Graphical Abstract: TPR, TPR-(act), s-TPR and s-TPR-(act) profiles of (1.36)Cu/SAPO-5 (A), (4.55)Cu/SAPO-5 (B) and (9.19)Cu/SAPO-5 (C) samples. The intensities of TCD signals in (A) and (B) are multiplied by 4.5 and 2, respectively. Highlights: → Cu supported on SAPO-5, alumina and zeolite Y was investigated by TPR and s-TPR. → Cu oxidation states can be discriminated and quantitatively determined. → In zeolite Y and SAPO-5 Cu 2+ cations are stabilized at weak and strong forms. → Strongly stabilized Cu 2+ cannot be auto-reduced in argon at 650 deg. C.

First-principles study of hydrogen diffusion in transition metal Rhodium

International Nuclear Information System (INIS)

Bao, Wulijibilige; Cui, Xin; Wang, Zhi-Ping

2015-01-01

In this study, the diffuse pattern and path of hydrogen in transition metal rhodium are investigated by the first-principles calculations. Density functional theory is used to calculate the system energies of hydrogen atom occupying different positions in rhodium crystal lattice. The results indicate that the most stable position of hydrogen atom in rhodium crystal lattice locates at the octahedral interstice, and the tetrahedral interstice is the second stable site. The activation barrier energy for the diffusion of atomic hydrogen in transition metal rhodium is quantified by determining the most favorable path, i.e., the minimum-energy pathway for diffusion, that is the indirect octahedral-tetrahedral-octahedral (O-T-O) pathway, and the activation energy is 0.8345eV

Kalman filtering for rhodium self-powered neutron detectors

International Nuclear Information System (INIS)

Kantrowitz, M.L.

1988-01-01

Rhodium self-powered neutron detectors are utilized in many pressurized water reactors to determine the neutronic behavior within the core. In order to compensate for the inherent time delay associated with the response of these detectors, a dynamic compensation algorithm is currently used in Combustion Engineering plants to reconstruct the dynamic flux signal which is being sensed by the rhodium detectors. This paper describes a new dynamic compensation algorithm, based on Kalman filtering, which improves on the noise gain and response time characteristics of the algorithm currently used, and offers the possibility of utilizing the proven rhodium detector based fixed in-core detector system as an integral part of advanced core control and/or protection systems

Advances in nanosized zeolites

Science.gov (United States)

Mintova, Svetlana; Gilson, Jean-Pierre; Valtchev, Valentin

2013-07-01

This review highlights recent developments in the synthesis of nanosized zeolites. The strategies available for their preparation (organic-template assisted, organic-template free, and alternative procedures) are discussed. Major breakthroughs achieved by the so-called zeolite crystal engineering and encompass items such as mastering and using the physicochemical properties of the precursor synthesis gel/suspension, optimizing the use of silicon and aluminium precursor sources, the rational use of organic templates and structure-directing inorganic cations, and careful adjustment of synthesis conditions (temperature, pressure, time, heating processes from conventional to microwave and sonication) are addressed. An on-going broad and deep fundamental understanding of the crystallization process, explaining the influence of all variables of this complex set of reactions, underpins an even more rational design of nanosized zeolites with exceptional properties. Finally, the advantages and limitations of these methods are addressed with particular attention to their industrial prospects and utilization in existing and advanced applications.

Preparation and Characterization of Zeolite Membrane for Bioethanol Purification

Directory of Open Access Journals (Sweden)

Aprilina Purbasari

2013-06-01

Full Text Available The use of bioethanol as an alternative fuel with a purity of more than 99.5% wt has prompted research on bioethanol purification. One of the promising methods used for bioethanol purification is pervaporation membrane. This research is aimed to prepare and characterize zeolite membranes for pervaporation membrane. The membrane preparation consisted of two stages, namely support preparation and zeolite deposition on the support. In support preparation, α- alumina and kaolin with specific composition (50:30; 40:40; 50:30 was mixed with additives and water. After pugging and aging process, the mixture became paste and extruded into tubular shape. The tube was then calcined at temperature of 1250 °C for 3 hours. After that, zeolite 4A was deposited on the tubes using clear solution made of 10 %wt zeolite and 90 %wt water and heated at temperature of 80 °C for 3 hours. Furthermore, the resulting zeolite membranes was washed with deionized water for 5 minutes and dried in oven at temperature of 100 °C for 24 hours. Characterization of zeolite membranes included mechanical strength test, XRD, and SEM. In the mechanical strength test, the membrane sample with α- alumina:kaolin = 50:30 (membrane A has the highest mechanical strength of 46.65 N/mm2. Result of XRD analysis for the membrane A indicated that mullite and corundum phases were formed, which mullite phase was more dominant. Meanwhile the result of SEM analysis shows that zeolite crystals have been formed and covered the pores support, but the deposition of zeolite has not been optimal yet. The performance examination for bioethanol purification showed that the membrane could increase the purity of bioethanol from 95% to 98.5% wt. © 2013 BCREC UNDIP. All rights reservedReceived: 23rd October 2012; Revised: 15th February 2013; Accepted: 16th February 2013[How to Cite: Purbasari, A., Istirokhatun, T., Devi, A.M., Mahsunnah, L. , Susanto, H. (2013. Preparation and Characterization of Zeolite

Synthesis of zeolite NaA membrane from fused fly ash extract.

Science.gov (United States)

Ameh, Alechine E; Musyoka, Nicholas M; Fatoba, Ojo O; Syrtsova, Daria A; Teplyakov, Vladimir V; Petrik, Leslie F

2016-01-01

Zeolite-NaA membranes were synthesized from an extract of fused South African fly ash on a porous titanium support by a secondary growth method. The influence of the synthesis molar regime on the formation of zeolite NaA membrane layer was investigated. Two synthesis mixtures were generated by adding either aluminium hydroxide or sodium aluminate to the fused fly ash extract. The feedstock material and the synthesized membranes were characterized by X-diffraction (XRD), scanning electron microscopy (SEM) and X-ray fluorescence spectroscopy (XRF). It was found by XRD and SEM that the cubic crystals of a typical zeolite NaA with a dense intergrown layer was formed on the porous Ti support. The study shows that the source of Al used had an effect on the membrane integrity as sodium aluminate provided the appropriate amount of Na(+) to form a coherent membrane of zeolite NaA, whereas aluminium hydroxide did not. Morphological, the single hydrothermal stage seeded support formed an interlocked array of zeolite NaA particles with neighbouring crystals. Also, a robust, continuous and well-intergrown zeolite NaA membrane was formed with neighbouring crystals of zeolite fused to each other after the multiple stage synthesis. The synthesized membrane was permeable to He (6.0 × 10(6) L m(-2)h(-1) atm(-1)) and CO2 (5.6 × 10(6) L m(-2)h(-1) atm(-1)), which indicate that the layer of the membrane was firmly attached to the porous Ti support. Membrane selectivity was maintained showing membrane integrity with permselectivity of 1.1, showing that a waste feedstock, fly ash, could be utilized for preparing robust zeolite NaA membranes on Ti support.

Low gravity containerless processing of immiscible gold rhodium alloys

Science.gov (United States)

Andrews, J. Barry

1986-01-01

Under normal one-g conditions immiscible alloys segregate extensively during solidification due to sedementation of the more dense of the immiscible liquid phases. However, under low-g conditions it should be possible to form a dispersion of the two immiscible liquids and maintain this dispersed structure during solidification. Immiscible (hypermonotectic) gold-rhodium alloys were processed in the Marshall Space Flight Center 105 meter drop tube in order to investigate the influence of low gravity, containerless solidification on their microstructure. Hypermonotectic alloys composed of 65 atomic % rhodium exhibited a tendency for the gold rich liquid to wet the outer surface of the containerless processed samples. This tendency led to extensive segregation in several cases. However, well dispersed microstructures consisting of 2 to 3 micron diameter rhodium-rich spheres in a gold-rich matrix were produced in 23.4 atomic % rhodium alloys. This is one of the best dispersions obtained in research on immiscible alloy-systems to data.

Free Rhodium (II) citrate and rhodium (II) citrate magnetic carriers as potential strategies for breast cancer therapy

Science.gov (United States)

2011-01-01

Background Rhodium (II) citrate (Rh2(H2cit)4) has significant antitumor, cytotoxic, and cytostatic activity on Ehrlich ascite tumor. Although toxic to normal cells, its lower toxicity when compared to carboxylate analogues of rhodium (II) indicates Rh2(H2cit)4 as a promising agent for chemotherapy. Nevertheless, few studies have been performed to explore this potential. Superparamagnetic particles of iron oxide (SPIOs) represent an attractive platform as carriers in drug delivery systems (DDS) because they can present greater specificity to tumor cells than normal cells. Thus, the association between Rh2(H2cit)4 and SPIOs can represent a strategy to enhance the former's therapeutic action. In this work, we report the cytotoxicity of free rhodium (II) citrate (Rh2(H2cit)4) and rhodium (II) citrate-loaded maghemite nanoparticles or magnetoliposomes, used as drug delivery systems, on both normal and carcinoma breast cell cultures. Results Treatment with free Rh2(H2cit)4 induced cytotoxicity that was dependent on dose, time, and cell line. The IC50 values showed that this effect was more intense on breast normal cells (MCF-10A) than on breast carcinoma cells (MCF-7 and 4T1). However, the treatment with 50 μM Rh2(H2cit)4-loaded maghemite nanoparticles (Magh-Rh2(H2cit)4) and Rh2(H2cit)4-loaded magnetoliposomes (Lip-Magh-Rh2(H2cit)4) induced a higher cytotoxicity on MCF-7 and 4T1 than on MCF-10A (p rhodium (II) citrate-loaded maghemite nanoparticles and magnetoliposomes induced more specific cytotoxicity on breast carcinoma cells than on breast normal cells, which is the opposite of the results observed with free Rh2(H2cit)4 treatment. Thus, magnetic nanoparticles represent an attractive platform as carriers in Rh2(H2cit)4 delivery systems, since they can act preferentially in tumor cells. Therefore, these nanopaticulate systems may be explored as a potential tool for chemotherapy drug development. PMID:21443799

Optimization of sodium loading on zeolite support for catalyzed transesterification of triolein with methanol.

Science.gov (United States)

Wang, Yu-Yuan; Chou, Hsin-Yu; Chen, Bing-Hung; Lee, Duu-Jong

2013-10-01

Optimization of sodium loading on zeolite HY for catalyzed transesterification of triolein in excess methanol to biodiesel was studied. Zeolite HY catalyst was activated by loading sodium ions to their surface via an ion-exchange method. The effects of ion-exchange process parameters, including the temperature, the process time, the pH value, as well as concentrations and sources of Na(+) cations (NaOH, NaCl and Na2SO4), on the conversion yield of triolein to biodiesel were investigated. Most of these Na(+)-activated zeolite HY catalysts could really facilitate the catalyzed transesterification reaction of triolein to biodiesel at a lower temperature near 65°C. Consequently, a high conversion yield of triglycerides to biodiesel at 97.3% was obtained at 65°C. Moreover, the durability of zeolite catalysts was examined as well. Catalytic performance tests of these zeolite catalysts in transesterification did not show a significant decrease in catalysis at least for three batch cycles. Copyright © 2013 Elsevier Ltd. All rights reserved.

Local Electric Field Effects on Rhodium-Porphyrin and NHC-Gold Catalysts

Science.gov (United States)

2015-01-05

AFRL-OSR-VA-TR-2015-0023 (NII) - Local Electric Field Effects on Rhodium -Porphyrin and NHC-Gold Catalysts MATTHEW KANAN LELAND STANFORD JUNIOR UNIV...Effects on Rhodium -Porphyrin and NHC-Gold Catalysts Principal Investigator: Matthew W. Kanan Project Publications: 1. “An Electric Field–Induced Change...Stanford University Grant/Contract Title The full title of the funded effort. (NII)-Local Electric Field Effects on Rhodium -Porphyrin and NHC-Gold

Cell-Selective Biological Activity of Rhodium Metalloinsertors Correlates with Subcellular Localization

Science.gov (United States)

Komor, Alexis C.; Schneider, Curtis J.; Weidmann, Alyson G.; Barton, Jacqueline K.

2013-01-01

Deficiencies in the mismatch repair (MMR) pathway are associated with several types of cancers, as well as resistance to commonly used chemotherapeutics. Rhodium metalloinsertors have been found to bind DNA mismatches with high affinity and specificity in vitro, and also exhibit cell-selective cytotoxicity, targeting MMR-deficient cells over MMR-proficient cells. Ten distinct metalloinsertors with varying lipophilicities have been synthesized and their mismatch binding affinities and biological activities determined. Although DNA photocleavage experiments demonstrate that their binding affinities are quite similar, their cell-selective antiproliferative and cytotoxic activities vary significantly. Inductively coupled plasma mass spectrometry (ICP-MS) experiments have uncovered a relationship between the subcellular distribution of these metalloinsertors and their biological activities. Specifically, we find that all of our metalloinsertors localize in the nucleus at sufficient concentrations for binding to DNA mismatches. However, the metalloinsertors with high rhodium localization in the mitochondria show toxicity that is not selective for MMR-deficient cells, whereas metalloinsertors with less mitochondrial rhodium show activity that is highly selective for MMR-deficient versus proficient cells. This work supports the notion that specific targeting of the metalloinsertors to nuclear DNA gives rise to their cell-selective cytotoxic and antiproliferative activities. The selectivity in cellular targeting depends upon binding to mismatches in genomic DNA. PMID:23137296

Electronic and magnetic properties of small rhodium clusters

Energy Technology Data Exchange (ETDEWEB)

Soon, Yee Yeen; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technology, Multimedia University, Melaka Campus, 75450 Melaka (Malaysia)

2015-04-24

We report a theoretical study of the electronic and magnetic properties of rhodium-atomic clusters. The lowest energy structures at the semi-empirical level of rhodium clusters are first obtained from a novel global-minimum search algorithm, known as PTMBHGA, where Gupta potential is used to describe the atomic interaction among the rhodium atoms. The structures are then re-optimized at the density functional theory (DFT) level with exchange-correlation energy approximated by Perdew-Burke-Ernzerhof generalized gradient approximation. For the purpose of calculating the magnetic moment of a given cluster, we calculate the optimized structure as a function of the spin multiplicity within the DFT framework. The resultant magnetic moments with the lowest energies so obtained allow us to work out the magnetic moment as a function of cluster size. Rhodium atomic clusters are found to display a unique variation in the magnetic moment as the cluster size varies. However, Rh{sub 4} and Rh{sub 6} are found to be nonmagnetic. Electronic structures of the magnetic ground-state structures are also investigated within the DFT framework. The results are compared against those based on different theoretical approaches available in the literature.

Antimicrobial properties of zeolite-X and zeolite-A ion-exchanged with silver, copper, and zinc against a broad range of microorganisms.

Science.gov (United States)

Demirci, Selami; Ustaoğlu, Zeynep; Yılmazer, Gonca Altın; Sahin, Fikrettin; Baç, Nurcan

2014-02-01

Zeolites are nanoporous alumina silicates composed of silicon, aluminum, and oxygen in a framework with cations, water within pores. Their cation contents can be exchanged with monovalent or divalent ions. In the present study, the antimicrobial (antibacterial, anticandidal, and antifungal) properties of zeolite type X and A, with different Al/Si ratio, ion exchanged with Ag(+), Zn(2+), and Cu(2+) ions were investigated individually. The study presents the synthesis and manufacture of four different zeolite types characterized by scanning electron microscopy and X-ray diffraction. The ion loading capacity of the zeolites was examined and compared with the antimicrobial characteristics against a broad range of microorganisms including bacteria, yeast, and mold. It was observed that Ag(+) ion-loaded zeolites exhibited more antibacterial activity with respect to other metal ion-embedded zeolite samples. The results clearly support that various synthetic zeolites can be ion exchanged with Ag(+), Zn(2+), and Cu(2+) ions to acquire antimicrobial properties or ion-releasing characteristics to provide prolonged or stronger activity. The current study suggested that zeolite formulations could be combined with various materials used in manufacturing medical devices, surfaces, textiles, or household items where antimicrobial properties are required.

Electrochemical behavior of rhodium(III) in 1-butyl-3-methylimidazolium chloride ionic liquid

Energy Technology Data Exchange (ETDEWEB)

Jayakumar, M.; Venkatesan, K.A. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India); Srinivasan, T.G. [Fuel Chemistry Division, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102 (India)], E-mail: tgs@igcar.gov.in

2008-02-15

Electrochemical behavior of rhodium(III) chloride in 1-butyl-3-methylimidazolium chloride was investigated by various electrochemical transient techniques at glassy carbon working electrode at different temperatures (343-373 K). Cyclic voltammogram of rhodium(III) in bmimCl consisted of a surge in reduction current occurring at a potential of -0.48 V (vs. Pd) is due to the reduction of Rh(III) to metallic rhodium and a very small oxidation wave occurring at -0.1 V. Increase of scan rate increases the peak current and remarkably shifts the cathodic peak potential (E{sub p}{sup c1}) in negative direction indicating the irreversibility of electroreduction of rhodium(III). The diffusion coefficient of rhodium(III) in bmimCl ({approx}10{sup -9} cm{sup 2}/s) was determined and the energy of activation ({approx}25 kJ/mol) was deduced from cyclic voltammograms at various temperatures. The cathodic ({tau}{sub r}) and anodic ({tau}{sub o}) transition times were measured from chronopotential transients and the ratio {tau}{sub o}/{tau}{sub r} was found to be 1:7. Electrowinning of rhodium from bmimCl medium results in a deposition of metallic rhodium with lower (20-25%) Faradaic efficiency. A separation factor of rhodium from co-existing noble metal fission product palladium in bmimCl was determined during electrodeposition.

Mesoporous zeolite single crystal catalysts: Diffusion and catalysis in hierarchical zeolites

DEFF Research Database (Denmark)

Christensen, Christina Hviid; Johannsen, Kim; Toernqvist, Eric

2007-01-01

During the last years, several new routes to produce zeolites with controlled mesoporosity have appeared. Moreover, an improved catalytic performance of the resulting mesoporous zeolites over conventional zeolites has been demonstrated in several reactions. In most cases, the mesoporous zeolites...... exhibit higher catalytic activity, but in some cases also improved selectivity and longer catalyst lifetime has been reported. The beneficial effects of introducing mesopores into the zeolites has in most instances been attributed to improved mass transport to and from the active sites located...... in the zeolite micropores. Here, we briefly discuss the most important ways of introducing mesopores into zeolites and, for the first time, we show experimentally that the presence of mesopores dramatically increases the rate of diffusion in zeolite catalysts. This is done by studying the elution of iso...

Catalytic Performance of Zeolite-Supported Vanadia in the Aerobic Oxidation of 5-hydroxymethylfurfural to 2,5- diformylfuran

DEFF Research Database (Denmark)

Sádaba, Irantzu; Gorbanev, Yury; Kegnæs, Søren

2013-01-01

on the four different zeolite supports H-beta, H-Y, H-mordenite, and H-ZSM-5 with 1–10 wt% vanadia loading were prepared and characterized by nitrogen physisorption, X-ray powder diffraction, scanning electron  microscopy, ammonia temperature-programmed desorption, Raman spectroscopy and UV...

Zeolite from fly ash: synthesis and characterization

Indian Academy of Sciences (India)

Unknown

to attempt making zeolite from fly ash (Höller and Wir- sching 1985; Henmi ... thermal treatment method to synthesize low silica NaX- type zeolite from .... catalytic applications. Mixture of ... amount of Fe2O3 and the oxides of Mg, Ca, P, Ti etc. The chemical ..... This work is partly supported by the Ministry of Human. Resource ...

Studies of Immobilized Homogeneous Metal Catalysts on Silica Supports

Energy Technology Data Exchange (ETDEWEB)

Stanger, Keith James [Iowa State Univ., Ames, IA (United States)

2003-01-01

The tethered, chiral, chelating diphosphine rhodium complex, which catalyzes the enantioselective hydrogenation of methyl-α-acetamidocinnamate (MAC), has the illustrated structure as established by ³¹P NMR and IR studies. Spectral and catalytic investigations also suggest that the mechanism of action of the tethered complex is the same as that of the untethered complex in solution. The rhodium complexes, [Rh(COD)H]₄, [Rh(COD)₂]⁺BF₄^-, [Rh(COD)Cl]₂, and RhCl₃• 3H₂O, adsorbed on SiO₂ are optimally activated for toluene hydrogenation by pretreatment with H₂ at 200 C. The same complexes on Pd-SiO₂ are equally active without pretreatments. The active species in all cases is rhodium metal. The catalysts were characterized by XPS, TEM, DRIFTS, and mercury poisoning experiments. Rhodium on silica catalyzes the hydrogenation of fluorobenzene to produce predominantly fluorocyclohexane in heptane and 1,2-dichloroethane solvents. In heptane/methanol and heptane/water solvents, hydrodefluorination to benzene and subsequent hydrogenation to cyclohexane occurs exclusively. Benzene inhibits the hydrodefluorination of fluorobenzene. In DCE or heptane solvents, fluorocyclohexane reacts with hydrogen fluoride to form cyclohexene. Reaction conditions can be chosen to selectively yield fluorocyclohexane, cyclohexene, benzene, or cyclohexane. The oxorhenium(V) dithiolate catalyst [-S(CH₂)₃s-]Re(O)(Me)(PPh₃) was modified by linking it to a tether that could be attached to a silica support. Spectroscopic investigation and catalytic oxidation reactivity showed the heterogenized catalyst's structure and reactivity to be similar to its homogeneous analog. However, the immobilized catalyst offered additional advantages of recyclability, extended stability, and increased resistance to deactivation.

Hydrothermal conversion of FAU zeolite into RUT zeolite in TMAOH system

OpenAIRE

Jon, Hery; Takahashi, Shoutarou; Sasaki, Hitoshi; Oumi, Yasunori; Sano, Tsuneji

2008-01-01

The highly crystalline and pure RUT (RUB-10) zeolite could be obtained from the hydrothermal conversion of FAU zeolite used as a crystalline Si/Al source in tetramethylammonium hydroxide (TMAOH) media. As compared to amorphous silica/Al(OH)3 and amorphous silica/γ-Al2O3 sources, the crystallization rate for the formation of RUT zeolite was clearly faster when FAU zeolite was employed as the Si/Al source. Moreover, it was found that the hydrothermal conversion of FAU zeolite into RUT zeolite d...

Bendable Zeolite Membranes: Synthesis and Improved Gas Separation Performance.

Science.gov (United States)

Wang, Bo; Ho, W S Winston; Figueroa, Jose D; Dutta, Prabir K

2015-06-23

Separation and sequestration of CO2 emitted from fossil energy fueled electric generating units and industrial facilities will help in reducing anthropogenic CO2, thereby mitigating its adverse climate change effects. Membrane-based gas separation has the potential to meet the technical challenges of CO2 separation if high selectivity and permeance with low costs for large-scale manufacture are realized. Inorganic zeolite membranes in principle can have selectivity and permeance considerably higher than polymers. This paper presents a strategy for zeolite growth within the pores of a polymer support, with crystallization time of an hour. With a thin coating of 200-300 nm polydimethylsiloxane (PDMS) on the zeolite-polymer composite, transport data for CO2/N2 separation indicate separation factors of 35-45, with CO2 permeance between 1600 and 2200 GPU (1 GPU = 3.35 × 10(-10) mol/(m(2) s Pa)) using dry synthetic mixtures of CO2 and N2 at 25 °C. The synthesis process results in membranes that are highly reproducible toward transport measurements and exhibit long-term stability (3 days). Most importantly, these membranes because of the zeolite growth within the polymer support, as contrasted to conventional zeolite growth on top of a support, are mechanically flexible.

Aluminum-rich mesoporous MFI - type zeolite single crystals

DEFF Research Database (Denmark)

Kustova, Marina; Kustov, Arkadii; Christensen, Christina Hviid

2005-01-01

Zeolitcs are crystalline materials, which are widely used as solid acid catalysts and supports in many industrial processes. Recently, mesoporous MFI-type zeolite single crystals were synthesized by use of carbon particles as a mesopore template and sodium aluminate as the aluminum Source....... With this technique, only zeolites with relatively low Al contents were reported (Si/Al ratio about 100). In this work, the preparation of aluminum-rich mesoporous MFI-type zeolite single crystals (Si/Al similar to 16-50) using aluminum isopropoxide as the aluminum Source is reported for the first time. All samples...... are characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), ammonia temperature programmed desorption (NH3-TPD), and N-2 adsorption measurements. The obtained zeolites combine the high crystallinity and the characteristic micropores of zeolites with an intracrystalline mesopore system...

Activity of iridium-ruthenium and iridium-rhodium adsorption catalysts in decomposition of hydrogen peroxide

Energy Technology Data Exchange (ETDEWEB)

Zubovich, I A; Mikhaylov, V A; Migulina, N N [Yaroslavskij Politekhnicheskij Inst. (USSR)

1976-06-01

Experimental data for the activities of iridium-ruthenium and iridium-rhodium adsorption catalysts in the decomposition of hydrogen peroxide are considered and the results of magnetic susceptibility measurements are presented. It is concluded that surface structures (complexes) may be formed and that micro-electronic feaures play a role in heterogeneous catalysis.

Characterization Of Cobalt-Exchanged Zeolite A By DRIFT Spectroscopy

Science.gov (United States)

Kappers, M. J.; van der Maas, John H.; Chalmers, J. M.; Howard, J.

1989-12-01

In-situ DRIFT spectroscopy has been succesfully used for the characterization of Co4Na4-A. Dehydration of the zeolite A appears to involve formation and breakdown of hydration complexes and hydrolysis. The position of cations and hydroxyl groups within the zeolite structure was derived from the adsorption of carbon monoxide and acetonitrile.

Rhodium self-powered neutron detector's lifetime for korean standard nuclear power plants

International Nuclear Information System (INIS)

Yoo, Choon Sung; Kim, Byoung Chul; Park, Jong Ho; Fero, Arnold H.; Anderson, S. L.

2005-01-01

A method to estimate the relative sensitivity of a self-powered rhodium detector for an upcoming cycle is developed by combining the rhodium depletion data from a nuclear design with the site measurement data. This method can be used both by nuclear power plant designers and by site staffs of Korean standard nuclear power plants for determining which rhodium detectors should be replaced during overhauls

Electrocatalytic Azide Oxidation Mediated by a Rh(PNP) Pincer Complex

NARCIS (Netherlands)

Rebreyend, Christophe; Gloaguen, Yann; Lutz, Martin; Van Der Vlugt, Jarl Ivar; Siewert, Inke; Schneider, Sven; Bruin, Bas De

2017-01-01

One-electron oxidation of the rhodium(I) azido complex [Rh(N3)(PNP)] (5), bearing the neutral, pyridine-based PNP ligand 2,6-bis(di-tert-butylphosphinomethyl)pyridine, leads to instantaneous and selective formation of the mononuclear rhodium(I) dinitrogen complex [Rh(N2)(PNP)]+ (9+). Interestingly,

Electrocatalytic Azide Oxidation Mediated by a Rh(PNP) Pincer Complex

NARCIS (Netherlands)

Rebreyend, C.; Gloaguen, Y.; Lutz, M.; van der Vlugt, J.I.; Siewert, I.; Schneider, S.; de Bruin, B.

2017-01-01

One-electron oxidation of the rhodium(I) azido complex [Rh(N3)(PNP)] ( 5 ), bearing the neutral, pyridine-based PNP ligand 2,6-bis(di-tert-butylphosphinomethyl)pyridine, leads to instantaneous and selective formation of the mononuclear rhodium(I) dinitrogen complex [Rh(N2)(PNP)]+ ( 9 +).

About the extraction recovery of fission rhodium from radioactive wastes

International Nuclear Information System (INIS)

Khaperskaya, A.V.; Renard, E.V.; Koltunov, V.S.

2000-01-01

The report will cover a radically new approach to the problem of rhodium recovery from HLLW after the transformation of kinetically inert poly-aqua cation of trivalent rhodium (which is not recoverable by the majority known extractants) to Rh (IV) form by chemical methods. Presented are the research results of Rh (IV) extraction from nitric acid solutions by several extractants that are of considerable current use in noble metals and radiochemical industries (tri-n-butyl phosphate, di-octyl-sulphide, tri-n-octylamine, quaternary ammonium bases). High level of rhodium extraction has been found for the above extractants: for several systems, for example, tri-n-octylamine - diethyl-benzene, rhodium distribution coefficient achieves high values (10-plus), as well as the sufficient extraction kinetics. Rhodium extraction increases with a decrease of the acidity, a rise in phase mixing time and in the following series: tri-n-butyl phosphate → di-octyl-sulphide → quaternary ammonium bases → tri-n-octylamine. Rh (IV) can be easily reduced to non-extractable Rh (III) by such reductants as Fe (II), HCOOH, C 6 H 8 O 6 , NH 2 OH, N 2 H 4 et al, that may be applied for the re-extraction process. (authors)

Synthesis of novel perfluoroalkylglucosides on zeolite and non-zeolite catalysts.

Science.gov (United States)

Nowicki, Janusz; Mokrzycki, Łukasz; Sulikowski, Bogdan

2015-04-08

Perfluoroalkylglucosides comprise a very important class of fluorine-containing surfactants. These compounds can be synthesized by using the Fisher reaction, starting directly from glucose and the required perfluoroalcohols. We wish to report on the use of zeolite catalysts of different structure and composition for the synthesis of perfluoroalkylglucosides when using glucose and 1-octafluoropentanol as substrates. Zeolites of different pore architecture have been chosen (ZSM-5, ZSM-12, MCM-22 and Beta). Zeolites were characterized by XRD, nitrogen sorption, scanning electron microscopy (SEM) and solid-state 27Al MAS NMR spectroscopy. The activity of the zeolite catalysts in the glycosidation reaction was studied in a batch reactor at 100 °C below atmospheric pressure. The performance of zeolites was compared to other catalysts, an ion-exchange resin (Purolite) and a montmorillonite-type layered aluminosilicate. The catalytic performance of zeolite Beta was the highest among the zeolites studied and the results were comparable to those obtained over Purolite and montmorillonite type catalysts.

Stereoselective hydrogenation of olefins using rhodium-substituted carbonic anhydrase--a new reductase.

Science.gov (United States)

Jing, Qing; Okrasa, Krzysztof; Kazlauskas, Romas J

2009-01-01

One useful synthetic reaction missing from nature's toolbox is the direct hydrogenation of substrates using hydrogen. Instead nature uses cofactors like NADH to reduce organic substrates, which adds complexity and cost to these reductions. To create an enzyme that can directly reduce organic substrates with hydrogen, researchers have combined metal hydrogenation catalysts with proteins. One approach is an indirect link where a ligand is linked to a protein and the metal binds to the ligand. Another approach is direct linking of the metal to protein, but nonspecific binding of the metal limits this approach. Herein, we report a direct hydrogenation of olefins catalyzed by rhodium(I) bound to carbonic anhydrase (CA-[Rh]). We minimized nonspecific binding of rhodium by replacing histidine residues on the protein surface using site-directed mutagenesis or by chemically modifying the histidine residues. Hydrogenation catalyzed by CA-[Rh] is slightly slower than for uncomplexed rhodium(I), but the protein environment induces stereoselectivity favoring cis- over trans-stilbene by about 20:1. This enzyme is the first cofactor-independent reductase that reduces organic molecules using hydrogen. This catalyst is a good starting point to create variants with tailored reactivity and selectivity. This strategy to insert transition metals in the active site of metalloenzymes opens opportunities to a wider range of enzyme-catalyzed reactions.

Column preconcentration and electrothermal atomic absorption spectrometric determination of rhodium in some food and standard samples.

Science.gov (United States)

Taher, Mohammad Ali; Pourmohammad, Fatemeh; Fazelirad, Hamid

2015-12-01

In the present work, an electrothermal atomic absorption spectrometric method has been developed for the determination of ultra-trace amounts of rhodium after adsorption of its 2-(5-bromo-2-pyridylazo)-5-diethylaminophenol/tetraphenylborate ion associated complex at the surface of alumina. Several factors affecting the extraction efficiency such as the pH, type of eluent, sample and eluent flow rates, sorption capacity of alumina and sample volume were investigated and optimized. The relative standard deviation for eight measurements of 0.1 ng/mL of rhodium was ±6.3%. In this method, the detection limit was 0.003 ng/mL in the original solution. The sorption capacity of alumina and the linear range for Rh(III) were evaluated as 0.8 mg/g and 0.015-0.45 ng/mL in the original solution, respectively. The proposed method was successfully applied for the extraction and determination of rhodium content in some food and standard samples with high recovery values. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydroformylation of propene and 1-hexene catalysed by a alpha-zirconium phosphate supported rhodium-phosphine complex

DEFF Research Database (Denmark)

Karlsson, Magnus; Andersson, C; Hjortkjær, Jes

2001-01-01

The reaction of the amphiphilic ligand {4-[bis(diethylaminoethyl)aminomethyl]diphenyl}phosphine with alpha -zirconium phosphate, of intermediate surface area (24m(2) g(-1)), provided a phosphine functionalised support in which electrostatic interaction between ammonium groups on the ligand and de......-protonated surface hydroxyl groups on the support provided the binding force. The X-ray powder diffractogram of the material showed that the binding lowers the crystallinity of the carrier and that the ligand is not intercalated but bound at the outer surface and at the entrances to the interlamellar space. Reaction...... of the phosphine functionalised support with Rh(CO)(2)(acac) led to CO-phosphine exchange and formation of an immobilised complex of the composition LRh(CO)(acac) (L = surface bound phosphine). When applied as catalyst in continuous gas-phase hydroformylation of propene and in liquid phase hydroformylation of 1...

Catalytic reactions of synthesis gas. Part 2. Methanol carbonylation and homologation

Energy Technology Data Exchange (ETDEWEB)

Niemelae, M.

1993-01-01

The aim of the review is to evaluate the applicability of methanol hydrocarbonylation as a second test reaction to study the nondissociative activation of CO by heterogeneous rhodium and cobalt catalysts. The main emphasis in methanol (hydro)carbonylation chemistry has been on homogeneous reactions. These systems have been seen advantageous in selectivity, activity and ease of modification. The heterogenization attempts have been carried out to obtain easier separation of the catalyst and the product. The activity of cobalt, rhodium and other metals supported on different materials have been studied in heterogeneous methanol (hydro)carbonylation. The observed activities have been considerably influenced by the support. The most effective catalyst support has been activated carbon. Good carbonylation activities and selectivities have also been observed in conjunction with zeolite supports. The literature study indicates that the typical experimental conditions of methanol (hydro)carbonylation do not exceed the constructional and operational limits of the available reactor system, i.e. 500 C and 50 bar. The reaction is suitable for testing Co and Rh precursors, since both cobalt and rhodium compounds have shown carbonylation activity.

"On-water" rhodium-catalysed hydroformylation for the production of linear alcohols

NARCIS (Netherlands)

Diebolt, O.H.; Müller, Christian; Vogt, D.

2012-01-01

Optimisation of the reaction conditions for the rhodium-catalysed aldehyde hydrogenation under hydroformylation conditions showed that water used as co-solvent enhances both rate and selectivity towards primary alcohols. One-pot hydroformylation–hydrogenation using rhodium as the only transition

Redox behavior of transition metal ions in zeolites--7. Characterization of a nickel metal phase in zeolite NaY

Energy Technology Data Exchange (ETDEWEB)

Jacobs, P.A. (Katholieke Univ. Leuven); Derouane, E.G.; Nijs, H.; Verdonck, J.; Gilson, J.P.; Simoens, A.J.

1979-01-01

NiY zeolite was calcined under steaming and nonsteaming conditions, at 823/sup 0/ and 1200/sup 0/K, respectively, then reduced in hydrogen at 673/sup 0/ to 873/sup 0/K for two hours. Characterization of the Ni(0) metal phase by temperature programed reduction and oxidation techniques and by ferromagnetic resonance spectroscopy indicated a bidisperse metal particle size distribution. Inside the zeolite, small Ni(0) particles were found, the sizes of which were limited by the dimensions of the supercage or of the structural defects occurring with high reduction temperatures; the particles interacted strongly with the support or were Vertical Bar3; 100Vertical Bar3< reduced. On the zeolite surface, large Ni(0) particles were formed which were ellipsoidal and completely reduced and did not interact with the support. Calcining under steaming conditions did not affect the reducibility of the nickel but did promote sintering during reduction.

Adsorption of CO2 in FAU zeolites: Effect of zeolite composition

Czech Academy of Sciences Publication Activity Database

Thang, H. V.; Grajciar, L.; Nachtigall, P.; Bludský, Ota; Areán, C. O.; Frýdová, E.; Bulánek, R.

2014-01-01

Roč. 227, May 15 (2014), s. 50-56 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388963 Keywords : DFT/CC * CO2 * carbon capture and storage * zeolite * adsorption calorimetry Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.893, year: 2014

Chemical changes associated with zeolitization of the tuffaceous beds of Calico Hills at Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Broxton, D.E.

1992-01-01

The chemistry of the tuffaceous beds of Calico Hills was examined in samples collected over a 100 2 km area south of the Timber Mountain-Oasis Valley caldera complex to determine regional geochemical patterns during zeolitization. Samples of 58 vitric and zeolitic tuffs were analyzed for 48 elements by a combination of x-ray fluorescence, atomic absorption spectrophotometry, and neutron activation analysis. Major and trace element concentrations for zeolitic tuffs vary significantly from those for vitric tuffs. Complex, geographically-controlled patterns of elemental enrichment and depletion in the zeolitic tuffs are found for Na, K, Ca, Mg, U, Rb, Sr, Ba and Cs. Vitric and zeolitic tuffs generally have the same SiO 2 contents on an anhydrous basis, but minor net silica gain or loss has occurred in some samples. Zeolitic tuffs from the northern part of the study area, adjacent to the caldera complex, are notably K-rich and Na- and U-poor compared to zeolitic tuffs to the south. The compositions of the K-rich zeolitic tuffs are similar to those found in other areas of the western US where volcanic rocks are affected by potassium metasomatism. Alteration of vitric tuffs took place in an open chemical system and geographic control of major element compositions probably reflects regional variations in groundwater chemistry during alteration. The K-rich zeolitic tuffs in the northern part of the study area were probably altered by hydrothermal fluids whereas tuffs further south were altered by lower-temperature groundwaters

A Bulky Rhodium Complex Bound to an Adenosine-Adenosine DNA Mismatch: General Architecture of the Metalloinsertion Binding Mode†

Science.gov (United States)

Zeglis, Brian M.; Pierre, Valérie C.; Kaiser, Jens T.; Barton, Jacqueline K.

2009-01-01

Two crystal structures are determined for Δ-Rh(bpy)2(chrysi)3+ (chrysi = 5,6-chrysenequinone diimine) bound to the oligonucleotide duplex 5′-CGGAAATTACCG-3′ containing two adenosine-adenosine mismatches (italics) through metalloinsertion. Diffraction quality crystals with two different space groups (P3221 and P43212) were obtained under very similar crystallization conditions. In both structures, the bulky rhodium complex inserts into the two mismatched sites from the minor groove side, ejecting the mismatched bases into the major groove. The conformational changes are localized to the mismatched site; the metal complex replaces the mismatched base pair without an increase in base pair rise. The expansive metal complex is accommodated in the duplex by a slight opening in the phosphodiester backbone; all sugars retain a C2′-endo puckering, and flanking base pairs neither stretch nor shear. The structures differ, however, in that in one of the structures, an additional metal complex is bound by intercalation from the major groove at the central 5′-AT-3′ step. We conclude that this additional metal complex is intercalated into this central step because of crystal packing forces. The structures described here of Δ-Rh(bpy)2(chrysi)3+ bound to thermodynamically destabilized AA mismatches share critical features with binding by metalloinsertion in two other oligonucleotides containing different single base mismatches. These results underscore the generality of the metalloinsertion as a new mode of non-covalent binding by small molecules with a DNA duplex. PMID:19374348

Structure and Reactivity of Zeolite- and Carbon-Supported Catalysts for the Oxidative Carbonylation of Alcohols

OpenAIRE

Briggs, Daniel Neal

2010-01-01

AbstractStructure and Reactivity of Zeolite- and Carbon-Supported Catalysts for the Oxidative Carbonylation of AlcoholsbyDaniel Neal BriggsDoctor of Philosophy in Chemical EngineeringUniversity of California, BerkeleyProfessor Alexis T. Bell, Chair The oxidative carbonylation of alcohols to produce dialkyl carbonates is a process that takes place commercially in a slurry of cuprous chloride in the appropriate alcohol. While this process is chemically efficient, it incurs costs in terms of ene...

Synthesis of Zeolite NaA from Low Grade (High Impurities) Indonesian Natural Zeolite

OpenAIRE

Mustain, Asalil; Wibawa, Gede; Nais, Mukhammad Furoiddun; Falah, Miftakhul

2014-01-01

The zeolite NaA has been successfully synthesized from the low grade natural zeolite with high impurities. The synthesis method was started by mixing natural zeolite powder with NH4Cl aqueous solution in the reactor as pretreatment. The use of pretreatment was to reduce the impurities contents in the zeolite. The process was followed by alkaline fusion hydrothermal treatment to modify the framework structure of natural zeolite and reduce the SiO2/Al2O3 ratio. Finally, the synthesized zeolite ...

Influence of zeolite structure on the activity and durability of Co-Pd-zeolite catalysts in the reduction of NOx with methane

International Nuclear Information System (INIS)

Pieterse, J.A.Z.; Van den Brink, R.W.; Booneveld, S.; De Bruijn, F.A.

2003-01-01

Selective catalytic reduction of NO with CH 4 was studied over ZSM-5, MOR, FER and BEA zeolite-based cobalt (Co) and palladium (Pd) catalysts in the presence of oxygen and water. As compared to other catalytic systems reported in literature for CH 4 -SCR in the presence of water, zeolite supported Co-Pd combination catalysts are very active and selective. The most active catalysts, based on MOR and ZSM-5, are characterised by well-dispersed Pd ions in the zeolite that activate methane. Wet ion exchange is a good method to achieve high dispersion of Pd provided that it is carried out in a competitive manner. The presence of cobalt (Co 3 O 4 , Co-oxo ions) boosts SCR activity by oxidising NO to NO 2 . The activity of the zeolite-based Co-Pd combination catalysts decreases with prolonged times on stream. The severity of the deactivation was found to be different for different zeolite topologies. The characterisation and evaluation of freshly calcined catalysts and spent catalysts show two things that occur during reaction: (1) zeolite solvated metal cations disappear in favour of (inactive) metal oxides and presumably larger metal entities, i.e. loss of dispersion; (2) loss of crystallinity affiliated with steam-dealumination and the concomitant formation of extra-framework aluminium (EFAL) in the presence of water. Both phenomena strongly depend on the (reaction) temperature. The deactivation of Co-Pd-zeolite resembles the deactivation of Pd-zeolite. Hence, future research could encompass the stabilisation of Pd (cations) in the zeolite pores by exploring additives other than cobalt. For this, detailed understanding on the siting of Pd in zeolites is important

Rhodium and Hafnium Influence on the Microstructure, Phase Composition, and Oxidation Resistance of Aluminide Coatings

OpenAIRE

Maryana Zagula-Yavorska; Małgorzata Wierzbińska; Jan Sieniawski

2017-01-01

A 0.5 μm thick layer of rhodium was deposited on the CMSX 4 superalloy by the electroplating method. The rhodium-coated superalloy was hafnized and aluminized or only aluminized using the Chemical vapour deposition method. A comparison was made of the microstructure, phase composition, and oxidation resistance of three aluminide coatings: nonmodified (a), rhodium-modified (b), and rhodium- and hafnium-modified (c). All three coatings consisted of two layers: the additive layer and the interdi...

Antitumor effect of free rhodium (II) citrate and rhodium (II) citrate-loaded maghemite nanoparticles on mice bearing breast cancer: a systemic toxicity assay.

Science.gov (United States)

Peixoto, Raphael Cândido Apolinário; Miranda-Vilela, Ana Luisa; de Souza Filho, José; Carneiro, Marcella Lemos' Brettas; Oliveira, Ricardo G S; da Silva, Matheus Oliveira; de Souza, Aparecido R; Báo, Sônia Nair

2015-05-01

Breast cancer is one of the most prevalent cancer types among women. The use of magnetic fluids for specific delivery of drugs represents an attractive platform for chemotherapy. In our previous studies, it was demonstrated that maghemite nanoparticles coated with rhodium (II) citrate (Magh-Rh2Cit) induced in vitro cytotoxicity and in vivo antitumor activity, followed by intratumoral administration in breast carcinoma cells. In this study, our aim was to follow intravenous treatment to evaluate the systemic antitumor activity and toxicity induced by these formulations in Balb/c mice bearing orthotopic 4T1 breast carcinoma. Female Balb/c mice were evaluated with regard to toxicity of intravenous treatments through analyses of hemogram, serum levels of alanine aminotransferase, iron, and creatinine and liver, kidney, and lung histology. The antitumor activity of rhodium (II) citrate (Rh2Cit), Magh-Rh2Cit, and maghemite nanoparticles coated with citrate (Magh-Cit), used as control, was evaluated by tumor volume reduction, histology, and morphometric analysis. Magh-Rh2Cit and Magh-Cit promoted a significant decrease in tumor area, and no experimental groups presented hematotoxic effects or increased levels of serum ALT and creatinine. This observation was corroborated by the histopathological examination of the liver and kidney of mice. Furthermore, the presence of nanoparticles was verified in lung tissue with no morphological changes, supporting the idea that our nanoformulations did not induce toxicity effects. No studies about the systemic action of rhodium (II) citrate-loaded maghemite nanoparticles have been carried out, making this report a suitable starting point for exploring the therapeutic potential of these compounds in treating breast cancer.

β-Zeolite modified by ethylenediamine for sorption of Th(IV)

Energy Technology Data Exchange (ETDEWEB)

Liu, Peng; Wu, Hanyu; Yuan, Ni; Yin, Zhuoxin; Pan, Duoqiang; Wu, Wangsuo [Lanzhou Univ. (China). Radiochemistry Lab.; Ministry of Education, Lanzhou (China). Key Lab. of Special Function Materials and Structure Design

2017-08-01

β-Zeolite-EDA was modified with ethylenediamine (EDA) after synthesized. The synthesized material was characterized and used for removal of Th(IV) from aqueous solutions. The influences of pH, ionic strength, contact time, temperature and humic acid (HA) on Th(IV) sorption onto synthesized β-zeolite-EDA was studied by batch technique. The dynamic process showed that the sorption of Th(IV) onto β-zeolite-EDA matched the pseudo-second-order kinetics model. The sorption of Th(IV) on β-zeolite-EDA was significantly dependent on pH values, the sorption percentage increased markedly at pH 3.5-4.5, and then maintained a steady state as pH values increased. Through simulating the sorption isotherms by Langmuir, Freundlich and Dubini-Radushkevich (D-R) models, it could be seen respectively that the sorption pattern of Th(IV) on β-zeolite-EDA was mainly controlled by surface complexation, and that the sorption processes was endothermic and spontaneous. The presence of HA increased Th(IV) sorption on β-zeolite-EDA.

Electron irradiation of zeolites

International Nuclear Information System (INIS)

Wang, S.X.; Wang, L.M.; Ewing, R.C.

1999-01-01

Three different zeolites (analcime, natrolite, and zeolite-Y) were irradiated with 200 keV and 400 keV electrons. All zeolites amorphized under a relatively low electron fluence. The transformation from the crystalline-to-amorphous state was continuous and homogeneous. The electron fluences for amorphization of the three zeolites at room temperature were: 7.0 x 10 19 e - /cm 2 (analcime), 1.8 x 10 20 e - /cm 2 (natrolite), and 3.4 x 10 20 e - /cm 2 (zeolite-Y). The different susceptibilities to amorphization are attributed to the different channel sizes in the structures which are the pathways for the release of water molecules and Na + . Natrolite formed bubbles under electron irradiation, even before complete amorphization. Analcime formed bubbles after amorphization. Zeolite-Y did not form bubbles under irradiation. The differences in bubble formation are attributed to the different channel sizes of the three zeolites. The amorphization dose was also measured at different temperatures. An inverse temperature dependence of amorphization dose was observed for all three zeolites: electron dose for amorphization decreased with increasing temperature. This unique temperature effect is attributed to the fact that zeolites are thermally unstable. A semi-empirical model was derived to describe the temperature effect of amorphization in these zeolites

Applications of natural zeolites on agriculture and food production.

Science.gov (United States)

Eroglu, Nazife; Emekci, Mevlut; Athanassiou, Christos G

2017-08-01

Zeolites are crystalline hydrated aluminosilicates with remarkable physical and chemical properties, which include losing and receiving water in a reverse way, adsorbing molecules that act as molecular sieves, and replacing their constituent cations without structural change. The commercial production of natural zeolites has accelerated during the last 50 years. The Structure Commission of the International Zeolite Association recorded more than 200 zeolites, which currently include more than 40 naturally occurring zeolites. Recent findings have supported their role in stored-pest management as inert dust applications, pesticide and fertilizer carriers, soil amendments, animal feed additives, mycotoxin binders and food packaging materials. There are many advantages of inert dust application, including low cost, non-neurotoxic action, low mammalian toxicity and safety for human consumption. The latest consumer trends and government protocols have shifted toward organic origin materials to replace synthetic chemical products. In the present review, we summarize most of the main uses of zeolites in food and agruculture, along with the with specific paradigms that illustrate their important role. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Synthesis and spectroscopic properties of Tris(2,2'-bipyridine)ruthenium(II) in zeolite Y

International Nuclear Information System (INIS)

DeWilde, W.; Peeters, G.; Lunsford, J.H.

1980-01-01

Tris(2,2'-bipyridine)ruthenium(II) complexes have been synthesized within the large cavities of dehydrated Y-type zeolites by allowing bipyridine to react with a Ru(NH 3 ) 6 -Y form of the zeolite. The resulting Ru(bpy) 3 2+ complexes are characterized by absorption and emission bands similar to those found in aqueous solutions. The relatively high concentration of the Ru(bpy) 3 2+ complexes resulted in concentration quenching. As the addition of water to the samples approached saturation, the luminescence was quenched; however, small amounts of water increased the luminescence in a sample which contained 2.8 complexes per unit cell. Emission was also quenched upon addition of O 2 to the zeolite, with the effect being more pronounced in samples having a smaller concentration of complexes. 30 references, 6 figures, 1 table

Rhodium-Catalyzed Linear Codimerization and Cycloaddition of Ketenes with Alkynes

Directory of Open Access Journals (Sweden)

Teruyuki Kondo

2010-06-01

Full Text Available A novel rhodium-catalyzed linear codimerization of alkyl phenyl ketenes with internal alkynes to dienones and a novel synthesis of furans by an unusual cycloaddition of diaryl ketenes with internal alkynes have been developed. These reactions proceed smoothly with the same rhodium catalyst, RhCl(PPh33, and are highly dependent on the structure and reactivity of the starting ketenes.

Rhodium(III)-Catalyzed Amidation of Unactivated C(sp(3) )-H Bonds.

Science.gov (United States)

Wang, He; Tang, Guodong; Li, Xingwei

2015-10-26

Nitrogenation by direct functionalization of C-H bonds represents an important strategy for constructing C-N bonds. Rhodium(III)-catalyzed direct amidation of unactivated C(sp(3) )-H bonds is rare, especially under mild reaction conditions. Herein, a broad scope of C(sp(3) )-H bonds are amidated under rhodium catalysis in high efficiency using 3-substituted 1,4,2-dioxazol-5-ones as the amide source. The protocol broadens the scope of rhodium(III)-catalyzed C(sp(3) )-H activation chemistry, and is applicable to the late-stage functionalization of natural products. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Stereoselective 1,3-Insertions of Rhodium(II) Azavinyl Carbenes

Science.gov (United States)

Chuprakov, Stepan; Worrell, Brady T.; Selander, Nicklas; Sit, Rakesh K.; Fokin, Valery V.

2014-01-01

Rhodium(II) azavinyl carbenes, conveniently generated from 1-sulfonyl-1,2,3-triazoles, undergo a facile, mild and convergent formal 1,3-insertion into N–H and O–H bonds of primary and secondary amides, various alcohols, and carboxylic acids to afford a wide range of vicinally bis-functionalized Z-olefins with perfect regio- and stereoselectively. Utilizing the distinctive functionality installed through these reactions, a number of subsequent rearrangements and cyclizations expand the repertoire of valuable organic building blocks constructed by reactions of transition metal carbene complexes, including α-allenyl ketones and amino-substituted heterocycles. PMID:24295389

The fabrication of porous 4A-zeolite-supported Ag nanoparticles catalysts and its catalytic activity for styrene epoxidation

Directory of Open Access Journals (Sweden)

Youkui Wu

Full Text Available Binderless hierarchically porous 4A-zeolite has been successful produced through hydrothermal crystallization, in which silicon-aluminum sol binded to the carbon nanofibers (CNFs, that is to say, where the CNFs powder was coated during the crystallization 4A-zeolite. The mixing of silica-alumina sol and CNFs was only a simple physical mixing process. The samples of micropores-macroporous hierarchical 4A-zeolite (P-4A-zeolite was analyzed by a series of characterization techniques, such as field emission scanning electron microscope (FESEM, transmission electron microscopy (TEM, simultaneous thermal analysis (STA and CO2 adsorption-desorption (BET and BJH, and so on. In addition, the adsorption test of silver nanoparticles was carried out. The characterization results indicated the presence of micropores and the formation of macroporous. At the same time, silver adsorption test proved that the prepared P-4A-zeolite had good adsorption performance and the catalytic performance of Ag/P-4A-zeolite was further investigated through the epoxidation of styrene. Keywords: Carbon nanofibers, Porous 4A-zeolite, Silver nanoparticles, Styrene epoxidation

In vitro permeation of platinum and rhodium through Caucasian skin.

Science.gov (United States)

Franken, A; Eloff, F C; Du Plessis, J; Badenhorst, C J; Jordaan, A; Du Plessis, J L

2014-12-01

During platinum group metals (PGMs) refining the possibility exists for dermal exposure to PGM salts. The dermal route has been questioned as an alternative route of exposure that could contribute to employee sensitisation, even though literature has been focused on respiratory exposure. This study aimed to investigate the in vitro permeation of platinum and rhodium through intact Caucasian skin. A donor solution of 0.3mg/ml of metal, K2PtCl4 and RhCl3 respectively, was applied to the vertical Franz diffusion cells with full thickness abdominal skin. The receptor solution was removed at various intervals during the 24h experiment, and analysed with high resolution ICP-MS. Skin was digested and analysed by ICP-OES. Results indicated cumulative permeation with prolonged exposure, with a significantly higher mass of platinum permeating after 24h when compared to rhodium. The mass of platinum retained inside the skin and the flux of platinum across the skin was significantly higher than that of rhodium. Permeated and skin retained platinum and rhodium may therefore contribute to sensitisation and indicates a health risk associated with dermal exposure in the workplace. Copyright © 2014 Elsevier Ltd. All rights reserved.

Distribution of metal and adsorbed guest species in zeolites

Energy Technology Data Exchange (ETDEWEB)

Chmelka, B.F.

1989-12-01

Because of their high internal surface areas and molecular-size cavity dimensions, zeolites are used widely as catalysts, shape- selective supports, or adsorbents in a variety of important chemical processes. For metal-catalyzed reactions, active metal species must be dispersed to sites within the zeolite pores that are accessible to diffusing reactant molecules. The distribution of the metal, together with transport and adsorption of reactant molecules in zeolite powders, are crucial to ultimate catalyst performance. The nature of the metal or adsorbed guest distribution is known, however, to be dramatically dependent upon preparatory conditions. Our objective is to understand, at the molecular level, how preparatory treatments influence the distribution of guest species in zeolites, in order that macroscopic adsorption and reaction properties of these materials may be better understood. The sensitivity of xenon to its adsorption environment makes {sup 129}Xe NMR spectroscopy an important diagnostic probe of metal clustering and adsorbate distribution processes in zeolites. The utility of {sup 129}Xe NMR depends on the mobility of the xenon atoms within the zeolite-guest system, together with the length scale of the sample heterogeneity being studied. In large pore zeolites containing dispersed guest species, such as Pt--NaY, {sup 129}Xe NMR is insensitive to fine structural details at room temperature.

Distribution of metal and adsorbed guest species in zeolites

International Nuclear Information System (INIS)

Chmelka, B.F.

1989-12-01

Because of their high internal surface areas and molecular-size cavity dimensions, zeolites are used widely as catalysts, shape- selective supports, or adsorbents in a variety of important chemical processes. For metal-catalyzed reactions, active metal species must be dispersed to sites within the zeolite pores that are accessible to diffusing reactant molecules. The distribution of the metal, together with transport and adsorption of reactant molecules in zeolite powders, are crucial to ultimate catalyst performance. The nature of the metal or adsorbed guest distribution is known, however, to be dramatically dependent upon preparatory conditions. Our objective is to understand, at the molecular level, how preparatory treatments influence the distribution of guest species in zeolites, in order that macroscopic adsorption and reaction properties of these materials may be better understood. The sensitivity of xenon to its adsorption environment makes 129 Xe NMR spectroscopy an important diagnostic probe of metal clustering and adsorbate distribution processes in zeolites. The utility of 129 Xe NMR depends on the mobility of the xenon atoms within the zeolite-guest system, together with the length scale of the sample heterogeneity being studied. In large pore zeolites containing dispersed guest species, such as Pt--NaY, 129 Xe NMR is insensitive to fine structural details at room temperature

Positron annihilation in modified zeolites LTA and 13X

Energy Technology Data Exchange (ETDEWEB)

Cabral-Prieto, A.; Garcia-Sosa, I.; Jimenez-Becerril, J. [Departamento de Quimica, Instituto Nacional de Investigaciones Nucleares, Apartado Postal 18-1027, Col. Escandon, Del. M. Hidalgo, Mexico D. F., c. p. 11801 (Mexico); Lopez-Castanares, R.; Olea-Cardoso, O. [Facultad de Quimica, Universidad Autonoma del Estado de Mexico, Paseo Tollocan esquina paseo Tollocan, esquina paseo Colon, Toluca, c. p. 50120, Estado de Mexico (Mexico)

2007-07-01

The pick-off annihilation lifetimes of o -Ps, {tau}{sub po}, in dehydrated Co{sup 2+} and Mn{sup 2+} exchanged zeolites LTA, in dehydrated Co{sup 2+} exchanged zeolite 13X, and in dehydrated Na{sup +} zeolites LTA and 13X, are estimated. Although {tau}{sub po} can be estimated from the lifetime spectra of the cation exchanged zeolites LTA and 13X, this lifetime can not be estimated from those spectra of Na{sup +} zeolite LTA unambiguously. The estimated pick-off lifetimes due to the annihilation of o-Ps in the internal walls of the zeolites are systematically lower than the average lifetime of p-Ps and o-Ps in vacuum {tau}{sub a}=0.5 ns. Since the pick-off process of o-Ps occurs particularly on the internal cavity walls of dehydrated zeolites, the replacement of {tau}{sub a} by {tau}{sub po} within the classical model of Tao-Eldrup to calculate cavity radius should provide more realistic cavity radii of these porous materials than when using {l_brace}{tau}{sub a}{r_brace}. This suggestion is supported by previous and present results. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Recent progress in the direct synthesis of hierarchical zeolites: synthetic strategies and characterization methods

KAUST Repository

Liu, Zhaohui

2017-06-16

Hierarchically structured zeolites combine the merits of microporous zeolites and mesoporous materials to offer enhanced molecular diffusion and mass transfer without compromising the inherent catalytic activities and selectivity of zeolites. This short review gives an introduction to the synthesis strategies for hierarchically structured zeolites with emphasis on the latest progress in the route of ‘direct synthesis’ using various templates. Several characterization methods that allow us to evaluate the ‘quality’ of complex porous structures are also introduced. At the end of this review, an outlook is given to discuss some critical issues and challenges regarding the development of novel hierarchically structured zeolites as well as their applications.

Synthesis and characterization of rhodium(I) complexes with P-N donor ligands and their catalytic application in transfer hydrogenation of carbonyl group

Energy Technology Data Exchange (ETDEWEB)

Barah, Geetika; Sarmah, Podma Poliov; Boruah, Devajani [Dept. of Chemistry, Dibrugarh University, Dibrugarh (India)

2015-04-15

Three rhodium(I) complexes of the types [Rh(COE)Cl(η{sup 2}-L)] (1a,1b) and [RhCl(η{sup 2}-L) (η{sup 1}-L)] (1c), where L = P⁓N donor ligands 2-[2-(diphenylphosphino) ethyl]pyridine, (PPh{sub 2}Etpy) (a), 2-(diphenylphosphino)pyridine (PPh{sub 2}py) (b), and 3-(diphenylphosphino)-1-propylamine (PPh{sub 2}(CH{sub 2}){sub 3}NH{sub 2}) (c), have been synthesized by reacting [Rh(coe){sub 2}Cl]{sub 2} with the respective ligands in 1:2 molar ratio for 1a, 1b and 1:4 molar ratio for 1c in DCM under refluxing condition. The complexes were characterized using different analytical techniques such as FT-IR, ESI(+) mass spectrometry, {sup 1}H and {sup 31}P{"1H} NMR spectrometry, conductivity measurements, and melting point determination. The synthesized complexes were found to exhibit good catalytic activity for the transfer hydrogenation of carbonyl compounds to corresponding alcohols with high conversion rate.

Hierarchical zeolites from class F coal fly ash

Science.gov (United States)

Chitta, Pallavi

Fly ash, a coal combustion byproduct is classified as types class C and class F. Class C fly ash is traditionally recycled for concrete applications and Class F fly ash often disposed in landfills. Class F poses an environmental hazard due to disposal and leaching of heavy metals into ground water and is important to be recycled in order to mitigate the environmental challenges. A major recycling option is to reuse the fly ash as a low-cost raw material for the production of crystalline zeolites, which serve as catalysts, detergents and adsorbents in the chemical industry. Most of the prior literature of fly ash conversion to zeolites does not focus on creating high zeolite surface area zeolites specifically with hierarchical pore structure, which are very important properties in developing a heterogeneous catalyst for catalysis applications. This research work aids in the development of an economical process for the synthesis of high surface area hierarchical zeolites from class F coal fly ash. In this work, synthesis of zeolites from fly ash using classic hydrothermal treatment approach and fusion pretreatment approach were examined. The fusion pretreatment method led to higher extent of dissolution of silica from quartz and mullite phases, which in turn led to higher surface area and pore size of the zeolite. A qualitative kinetic model developed here attributes the difference in silica content to Si/Al ratio of the beginning fraction of fly ash. At near ambient crystallization temperatures and longer crystallization times, the zeolite formed is a hierarchical faujasite with high surface area of at least 360 m2/g. This work enables the large scale recycling of class F coal fly ash to produce zeolites and mitigate environmental concerns. Design of experiments was used to predict surface area and pore sizes of zeolites - thus obviating the need for intense experimentation. The hierarchical zeolite catalyst supports tested for CO2 conversion, yielded hydrocarbons

Electrochemical Sensor Based on Rh(III) Ion-Imprinted Polymer as a New Modifying Agent for Rhodium Determination.

Science.gov (United States)

Bai, Huiping; Xiong, Caiyun; Wang, Chunqiong; Liu, Peng; Dong, Su; Cao, Qiue

2018-05-01

A rhodium (III) ion carbon paste electrode (CPE) based on an ion imprinted polymer (IIP) as a new modifying agent has been prepared and studied. Rh(III) ion imprinted polymer was synthesized by copolymerization of acrylamide-Rh(III) complex and ethylene glycol dimethacrylate according to the precipitation polymerization. Acrylamide acted as both functional monomer and complexing agent to create selective coordination sites in a cross-linked polymer. The ion imprinted carbon paste electrode (IIP-CPE) was prepared by mixing rhodium IIP-nanoparticles and graphite powder in n-eicosane as an adhesive and then embedding them in a Teflon tube. Amperometric i-t curve method was applied as the determination technique. Several parameters, including the functional monomer, molar ratio of template, monomer and cross-linking agent, the amounts of IIP, the applied potential, the buffer solution and pH have been studied. According to the results, IIP-CPE showed a considerably higher response in comparison with the electrode embedded with non-imprinted polymer (NIP), indicating the formation of suitable recognition sites in the IIP structure during the polymerization stage. The introduced electrode showed a linear range of 1.00×10-8~3.0×10-5 mol·L-1 and detection limit of 6.0 nmol L-1 (S/N = 3). The IIP-CPE was successfully applied for the trace rhodium determination in catalyst and plant samples with RSD of less than 3.3% (n = 5) and recoveries in the range of 95.5~102.5%.

Removal of ethylene from air stream by adsorption and plasma-catalytic oxidation using silver-based bimetallic catalysts supported on zeolite.

Science.gov (United States)

Trinh, Quang Hung; Lee, Sang Baek; Mok, Young Sun

2015-03-21

Dynamic adsorption of ethylene on 13X zeolite-supported Ag and Ag-M(x)O(y) (M: Co, Cu, Mn, and Fe), and plasma-catalytic oxidation of the adsorbed ethylene were investigated. The experimental results showed that the incorporation of Ag into zeolite afforded a marked enhancement in the adsorptivity for ethylene. The addition of transition metal oxides was found to have a positive influence on the ethylene adsorption, except Fe(x)O(y). The presence of the additional metal oxides, however, appeared to somewhat interrupt the diffusion of ozone into the zeolite micro-pores, leading to a decrease in the plasma-catalytic oxidation efficiency of the ethylene adsorbed there. Among the second additional metal oxides, Fe(x)O(y) was able to reduce the emission of ozone during the plasma-catalytic oxidation stage while keeping a high effectiveness for the oxidative removal of the adsorbed ethylene. The periodical treatment consisting of adsorption followed by plasma-catalytic oxidation may be a promising energy-efficient ethylene abatement method. Copyright © 2014 Elsevier B.V. All rights reserved.

Rhodium-catalyzed regioselective olefination directed by a carboxylic group.

Science.gov (United States)

Mochida, Satoshi; Hirano, Koji; Satoh, Tetsuya; Miura, Masahiro

2011-05-06

The ortho-olefination of benzoic acids can be achieved effectively through rhodium-catalyzed oxidative coupling with alkenes. The carboxylic group is readily removable to allow ortho-olefination/decarboxylation in one pot. α,β-Unsaturated carboxylic acids such as methacrylic acid also undergo the olefination at the β-position. Under the rhodium catalysis, the cine-olefination of heteroarene carboxylic acids such as thiophene-2-carboxylic acid proceeds smoothly accompanied by decarboxylation to selectively produce the corresponding vinylheteroarene derivatives. © 2011 American Chemical Society

Relationship between electronic structure and electric conductivity of double rhodium oxides from X-ray spectral data

International Nuclear Information System (INIS)

Firsov, M.N.; Nefedov, V.I.; Shaplygin, I.S.

1983-01-01

Quantum yield spectra of X-ray photoemission of O K - and Rh M 3 -bands of double rhodium oxides with Be, Mg, Ca, Sr, Ba, Cd, V, Nb, Ta, Mo, W are obtained. Quantum yield spectra are analogous to absorption spectra and reflect vacant states in a crystal, in particular, the quantum yield spectrum of O K-band is associated with oxygen vacant states of p-symmetry while Rh M 3 -band spectrum with rhomium vacant states of d-symmetry. In all rhodium compounds investigated the first vacant band is formed by the rhodium 4d-states. The forbidden zone between the last occupied and first free states of rhodiUm has a small width (eV fractions), which explains the semiconductor character of electric conductivity of the investigated compounds. Electric resistance variation in investigated series of rhodium compounds is in agreement with peculiarities of their electronic structure and entirely depends on variation in the electron density on rhodium atoms

Synthesis of zeolite NaA membrane from fused fly ash extract

CSIR Research Space (South Africa)

Ameh, AE

2016-01-01

Full Text Available Zeolite-NaA membranes were synthesized from an extract of fused South African fly ash on a porous titanium support by a secondary growth method. The influence of the synthesis molar regime on the formation of zeolite NaA membrane layer...

XAFS Study on TiO2 Photocatalyst Loaded on Zeolite Synthesized from Steel Slag

International Nuclear Information System (INIS)

Kuwahara, Yasutaka; Ohmichi, Tetsutaro; Mori, Kosuke; Katayama, Iwao; Yamashita, Hiromi

2007-01-01

The convenient route for the synthesis of Y-zeolites by utilizing steel slag as a material source was developed. Through hydrothermal treatment, well-crystallized Y-zeolite was obtained. We also synthesized TiO2-loaded Y-zeolites by an impregnation method. The structure of titanium oxide species highly dispersed on the zeolite, which couldn't be detected by XRD patterns, was investigated by XAFS analysis. Photocatalytic activity for decomposition of 2-propanol in liquid phase was found to be enhanced by the hydrophobic surface property of zeolite. It has been demonstrated that the zeolite synthesized from steel slag would be applicable as a promising support of TiO2 photocatalyst

Use of Natural Zeolite to Upgrade Activated Sludge Process

Directory of Open Access Journals (Sweden)

Hanife Büyükgüngör

2003-01-01

Full Text Available The objective of this study was to achieve better efficiency of phosphorus removal in an enhanced biological phosphorus removal process by upgrading the system with different amounts of natural zeolite addition. The system performance for synthetic wastewater containing different carbon sources applied at different initial concentrations of phosphorus, as well as for municipal wastewater, was investigated. Natural zeolite addition in the aerobic phase of the anaerobic/aerobic bioaugmented activated sludge system contributed to a significant improvement of phosphorus removal in systems with synthetic wastewater and fresh municipal wastewater. Improvement of phosphorus removal with regard to the control reactors was higher with the addition of 15 than with 5 g/L of natural zeolite. In reactors with natural zeolite addition with regard to the control reactors significantly decreased chemical oxygen demand, ammonium and nitrate, while higher increment and better-activated sludge settling were achieved, without changes in the pH-values of the medium. It was shown that the natural zeolite particles are suitable support material for the phosphate-accumulating bacteria Acinetobacter calcoaceticus (DSM 1532, which were adsorbed on the particle surface, resulting in increased biological activity of the system. The process of phosphorus removal in a system with bioaugmented activated sludge and natural zeolite addition consisted of: metabolic activity of activated sludge, phosphorus uptake by phosphate-accumulating bacteria adsorbed on the natural zeolite particles and suspended in solution, and phosphorus adsorption on the natural zeolite particles.

Superconductivity in zirconium-rhodium alloys

Science.gov (United States)

Zegler, S. T.

1969-01-01

Metallographic studies and transition temperature measurements were made with isothermally annealed and water-quenched zirconium-rhodium alloys. The results clarify both the solid-state phase relations at the Zr-rich end of the Zr-Rh alloy system and the influence upon the superconducting transition temperature of structure and composition.

Continuous gas-phase hydroformylation of 1-butene using supported ionic liquid phase (SILP) catalysts

DEFF Research Database (Denmark)

Haumann, Marco; Dentler, Katharina; Joni, Joni

2007-01-01

The concept of supported ionic liquid phase (SILP) catalysis has been extended to 1-butene hydroformylation. A rhodium-sulfoxantphos complex was dissolved in [BMIM][n-C8H17OSO3] and this solution was highly dispersed on silica. Continuous gas-phase experiments in a fixed-bed reactor revealed...

REGIOSELECTIVE OXIDATIONS OF EQUILENIN DERIVATIVES CATALYZED BY A RHODIUM (III) PORPHYRIN COMPLEX-CONTRAST WITH THE MANGANESE (III) PORPHYRIN. (R826653)

Science.gov (United States)

AbstractEquilenin acetate and dihydroequilenin acetate were oxidized with iodosobenzene and a rhodium(III) porphyrin catalyst. The selectivity of the reactions differs from that with the corresponding Mn(III) catalyst, or from that of free radical chain oxidation.

MECHANISMS OF THE COMPLEX FORMATION BY d-METALS ON POROUS SUPPORTS AND THE CATALYTIC ACTIVITY OF THE FORMED COMPLEXES IN REDOX REACTIONS

Directory of Open Access Journals (Sweden)

T. L. Rakitskaya

2015-11-01

Full Text Available The catalytic activity of supported complexes of d metals in redox reactions with participation of gaseous toxicants, PH3, CO, O3, and SO2, depends on their composition. Owing to the variety of physicochemical and structural-adsorption properties of available supports, their influence on complex formation processes, the composition and catalytic activity of metal complexes anchored on them varies over a wide range. The metal complex formation on sup-ports with weak ion-exchanging properties is similar to that in aqueous solutions. In this case, the support role mainly adds up to the ability to reduce the activity of water adsorbed on them. The interaction between a metal complex and a support surface occurs through adsorbed water molecules. Such supports can also affect complex formation processes owing to protolytic reactions on account of acidic properties of sorbents used as supports. The catalytic activity of metal complexes supported on polyphase natural sorbents considerably depends on their phase relationship. In the case of supports with the nonsimple structure and pronounced ion-exchanging properties, for instance, zeolites and laminar silicates, it is necessary to take into account the variety of places where metal ions can be located. Such location places determine distinctions in the coordination environment of the metal ions and the strength of their bonding with surface adsorption sites and, therefore, the catalytic activity of surface complexes formed by theses metal ions. Because of the energy surface inhomogeneity, it is important to determine a relationship between the strength of a metal complex bonding with a support surface and its catalytic activity. For example, bimetallic complexes are catalytically active in the reactions of oxidation of the above gaseous toxicants. In particular, in the case of carbon monoxide oxidation, the most catalytic activity is shown by palladium-copper complexes in which copper(II is strongly

Synthesis of zeolite-zeolite (mfi-fau) composite catalysts for the isomerization of n-hexane

International Nuclear Information System (INIS)

Ghouri, A.S; Usman, M.R.

2017-01-01

In this research work, the aim is to produce a relatively novel zeolite-zeolite (MFI-FAU) composite catalyst having better potential of catalyzing isomerization of lighter hydrocarbons such as light naphtha, n-pentane, n-hexane, n-heptane and mixture thereof. A series of zeolite-zeolite (MFI-FAU) composite catalysts have been synthesized by incorporating previous practices and techniques. The catalytic performance of as-synthesized zeolite-zeolite (MFI-FAU) composite catalysts have been investigated by isomerizing 95% pure n-hexane in conventional fixed bed flow micro-reactor at temperature 200-240 ºC under atmospheric pressure. In order to explore chemical and physical features of zeolite-zeolite (MFI-FAU) composite catalysts, they are examined and characterized using powder X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectrometry (EDX), N2 adsorption-desorption measurements (BET, BJH, t-plot measurements) and Fourier transform infrared (FTIR) spectroscopy equipped with attenuated total reflectance (ATR) arrangements. (author)

Nanosized zeolites as a perspective material for conductometric biosensors creation

Science.gov (United States)

Kucherenko, Ivan; Soldatkin, Oleksandr; Kasap, Berna Ozansoy; Kirdeciler, Salih Kaan; Kurc, Burcu Akata; Jaffrezic-Renault, Nicole; Soldatkin, Alexei; Lagarde, Florence; Dzyadevych, Sergei

2015-05-01

In this work, the method of enzyme adsorption on different zeolites and mesoporous silica spheres (MSS) was investigated for the creation of conductometric biosensors. The conductometric transducers consisted of gold interdigitated electrodes were placed on the ceramic support. The transducers were modified with zeolites and MSS, and then the enzymes were adsorbed on the transducer surface. Different methods of zeolite attachment to the transducer surface were used; drop coating with heating to 200°C turned out to be the best one. Nanozeolites beta and L, zeolite L, MSS, and silicalite-1 (80 to 450 nm) were tested as the adsorbents for enzyme urease. The biosensors with all tested particles except zeolite L had good analytical characteristics. Silicalite-1 (450 nm) was also used for adsorption of glucose oxidase, acetylcholinesterase, and butyrylcholinesterase. The glucose and acetylcholine biosensors were successfully created, whereas butyrylcholinesterase was not adsorbed on silicalite-1. The enzyme adsorption on zeolites and MSS is simple, quick, well reproducible, does not require use of toxic compounds, and therefore can be recommended for the development of biosensors when these advantages are especially important.

A study on the sensitivity depletion laws for rhodium self-powered neutron detectors

International Nuclear Information System (INIS)

Kim, Gil Gon

1999-02-01

The rhodium self-powered neutron detectors (SPND) in a reactor core provide the operator with the on-line 3-dimensional nuclear power distribution. The signal produced by rhodium SPND is interpreted into the local neutron flux by using a sensitivity depletion law and the local neutron flux is interpreted into the local power by using a power conversion factor. This work on the sensitivity depletion laws for rhodium self-powered neutron detectors (SPND) is performed to improve the uncertainty of the sensitivity depletion law used in ABB-CE reactors employing a rhodium SPND and to develop a calculational tool for providing the sensitivity depletion laws to interpret the signal of the newly designed rhodium SPND into the local neutron flux. The calculational tools for a time dependent neutron flux distribution in the rhodium emitter during depletion and for a time dependent beta escape probability that a beta generated in the emitter is escaped into the collector were developed. Due to the cost, the exposure to the radiation, and the longer fuel cycle, there is a strong incentive that the loading density of an in-core instrumentation is reduced and the lifetime of the detector is lengthened. These objectives can be achieved by reducing the uncertainty which is amplified as it depletes. The calculational tools above provide the sensitivity depletion law and show the reduction of the uncertainty to about 1 % in interpreting the signal into the local neutron flux compared to the method employed by ABB-CE. The reduction in the uncertainty of 1 % in interpreting the signal into the local neutron flux is equivalent to the reduction in the uncertainty of 1 % or more in interpreting the signal into the local power and to the extension of the lifetime of rhodium SPND to about 10 % as reported by ABB-CE

Pore Topology Effects in Positron Annihilation Spectroscopy of Zeolites.

Science.gov (United States)

Zubiaga, Asier; Warringham, Robbie; Mitchell, Sharon; Gerchow, Lars; Cooke, David; Crivelli, Paolo; Pérez-Ramírez, Javier

2017-03-03

Positron annihilation spectroscopy (PAS) is a powerful method to study the size and connectivity of pores in zeolites. The lifetime of positronium within the host material is commonly described by the Tao-Eldrup model. However, one of its largest limitations arises from the simple geometries considered for the shape of the pores, which cannot describe accurately the complex topologies in zeolites. Here, an atomic model that combines the Tao potential with the crystallographic structure is introduced to calculate the distribution and lifetime of Ps intrinsic to a given framework. A parametrization of the model is undertaken for a set of widely applied zeolite framework types (*BEA, FAU, FER, MFI, MOR, UTL), before extending the model to all known structures. The results are compared to structural and topological descriptors, and to the Tao-Eldrup model adapted for zeolites, demonstrating the intricate dependence of the lifetime on the pore architecture. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Remarkable catalytic properties of hierarchical zeolite-Beta in epoxide rearrangement reactions

Czech Academy of Sciences Publication Activity Database

García-Munoz, J.L.; Serrano, D. P.; Vicente, G.; Linares, M.; Vitvarová, Dana; Čejka, Jiří

2015-01-01

Roč. 243, APR 2015 (2015), s. 141-152 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : hierarchical zeolites * zeolite beta * hybridzeolitic - mesostructured materials Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.312, year: 2015

Surfactant-modified zeolites as permeable barriers to organic and inorganic groundwater contaminants

International Nuclear Information System (INIS)

Bowman, R.S.; Sullivan, E.J.

1995-01-01

We have shown in laboratory experiments that natural zeolites treated with hexadecyltrimethylammonium (HDTMA) are effective sorbents for nonpolar organics, inorganic cations, and inorganic anions. Due to their low cost (∼$0.75/kg) and granular nature, HDTMA-zeolites appear ideal candidates for reactive, permeable subsurface barriers. The HDTMA-zeolites are stable over a wide range of pH (3-13), ionic strength (1 M Cs + or Ca 2+ ), and in organic solvents. Surfactant-modified zeolites sorb nonpolar organics (benzene, toluene, xylene, chlorinated aliphatics) via a partitioning mechanism, inorganic cations (Pb 2+ ) via ion exchange and surface complexation, and inorganic anions (CrO 4 2- , SeO 4 2- , SO 4 2- ) via surface precipitation.The goal of this work is to demonstrate the use of surfactant-modified zeolite as a permeable barrier to ground water contaminants

A Novel Seeding Method of Interfacial Polymerization-Assisted Dip Coating for the Preparation of Zeolite NaA Membranes on Ceramic Hollow Fiber Supports.

Science.gov (United States)

Cao, Yue; Wang, Ming; Xu, Zhen-Liang; Ma, Xiao-Hua; Xue, Shuang-Mei

2016-09-28

A novel seeding method combining interfacial polymerization (IP) technique with dip-coating operation was designed for directly coating nanosized NaA seed crystals (150 nm) onto the micrometer-sized α-Al2O3 hollow fiber support, in which the polyamide (PA) produced by IP acted as an effective medium to freeze and fix seed crystals at the proper position so that the controlled seed layer could be accomplished. While a coating suspension with only 0.5 wt % seed content was used, a very thin seed layer with high quality and good adhesion was achieved through dip coating twice without drying between, and the whole seeding process was operated at ambient conditions. The resulting zeolite NaA membranes not only exhibited high pervaporation (PV) performance with an average separation factor above 10000 and flux nearly 9.0 kg/m(2)·h in dehydration of 90 wt % ethanol aqueous solution at 348 K but also demonstrated great reproducibility by testing more than eight batches of zeolite membranes. In addition, this seeding strategy could be readily extended to the preparation of other supported zeolite membranes for a wide range of separation applications.

Probing the structure of complex solids using a distributed computing approach-Applications in zeolite science

International Nuclear Information System (INIS)

French, Samuel A.; Coates, Rosie; Lewis, Dewi W.; Catlow, C. Richard A.

2011-01-01

We demonstrate the viability of distributed computing techniques employing idle desktop computers in investigating complex structural problems in solids. Through the use of a combined Monte Carlo and energy minimisation method, we show how a large parameter space can be effectively scanned. By controlling the generation and running of different configurations through a database engine, we are able to not only analyse the data 'on the fly' but also direct the running of jobs and the algorithms for generating further structures. As an exemplar case, we probe the distribution of Al and extra-framework cations in the structure of the zeolite Mordenite. We compare our computed unit cells with experiment and find that whilst there is excellent correlation between computed and experimentally derived unit cell volumes, cation positioning and short-range Al ordering (i.e. near neighbour environment), there remains some discrepancy in the distribution of Al throughout the framework. We also show that stability-structure correlations only become apparent once a sufficiently large sample is used. - Graphical Abstract: Aluminium distributions in zeolites are determined using e-science methods. Highlights: → Use of e-science methods to search configurationally space. → Automated control of space searching. → Identify key structural features conveying stability. → Improved correlation of computed structures with experimental data.

Characterization of gallium-containing zeolites for catalytic applications

Energy Technology Data Exchange (ETDEWEB)

Garcia Sanchez, M.

2003-12-08

The present study considers the synthesis, characterization, and catalytic evaluation of extra-framework gallium-containing zeolites. We focus on modification of zeolites by chemical vapor deposition of trimethylgallium on HZSM-5 and Mordenite zeolites. Chapter 2 is dedicated to the chemisorption and stability of TMG on HZSM-5 and HMOR zeolites. The effect of silylation is also addressed. Some theoretical calculations are also shown in this study to support part of the experimental results. In Chapter 3, the effect of oxidation and reduction treatments on these catalysts is investigated by FTIR, ICP and multinuclei NMR. In Chapter 4, the oxidation state and Ga coordination obtained during and after thermal treatment with H2 and O2 is analysed by X-ray adsorption spectroscopy (XANES and EXAFS) and IR analysis of CO adsorption. These results allow a better understanding of the catalytic behaviour of Ga-containing zeolites catalyst. Chapter 5 consists of two parts: one discusses the H2 activation over Ga/HZSM5 and Ga/MOR catalysts by H2/D2 isotopic exchange reaction, and the second part deals with the aromatization of n-heptane over the same catalysts.

Preparation, Characterization and NO-CO Redox Reaction Studies over Palladium and Rhodium Oxides Supported on Manganese Dioxide

Directory of Open Access Journals (Sweden)

M.S. Fal Desai

2015-03-01

Full Text Available The catalytic activity of PdO/MnO2 and Rh2O3/MnO2 is investigated for NO-CO redox reaction. Supported catalysts are prepared by wet impregnation method. Among the tested catalysts, PdO/MnO2 shows higher activity for this reaction. Active metal dispersion on MnO2 enhances the selectivity for N2 over N2O in this reaction. The XRD substantiate the formation of MnO2 monophasic phase. SEM images show the formation of elongated particles. TEM images indicate nano-size rod-like morphologies. An increase in the catalytic activity is observed on supported Pd and Rh oxides on MnO2. Temperature programed desorption studies with NO and CO are undertaken to investigate the catalytic surface studies. © 2015 BCREC UNDIP. All rights reservedReceived: 22nd November 2014; Revised: 31st December 2014; Accepted: 2nd January 2015How to Cite: Fal Desai, M.S., Kunkalekar, R.K., Salker, A.V. (2015. Preparation, Characterization and NO-CO Redox Reaction Studies over Palladium and Rhodium Oxides Supported on Manganese Dioxide. Bulletin of Chemical Reaction Engineering & Catalysis, 10 (1: 98-103. (doi:10.9767/bcrec.10.1.7802.98-103Permalink/DOI: http://dx.doi.org/10.9767/bcrec.10.1.7802.98-103 

Evaluation of the rheological behavior of asphaltic binder modified with zeolite material

Energy Technology Data Exchange (ETDEWEB)

Silveira, E.M. da; Sant' ana, Hosiberto B.; Soares, Sandra A.; Soares, Jorge B. [Federal University of Ceara, Fortaleza, CE (Brazil)

2008-07-01

Several new processes have been developed to reduce mixing and compaction temperatures of hot mix asphalt without sacrificing the quality of the resulting pavement. One of these processes utilizes the zeolite, a crystalline hydrated aluminum silicate. A laboratory study was conducted to determine the applicability of zeolite to improve the rheological and chemical behavior of an asphaltic binder. The synthetic asphaltic binder was produced with different zeolite contents (0,1; 0.3; and 0.5% w/w) by wet process. The rheological and chemical behavior was verified by Dynamic Shear Rheometer and Infrared Spectroscopy, respectively. The zeolite's chemical composition and morphology was studied by Dispersive X-ray Spectroscopy (EDX). Additionally, the scanning electron microscope (SEM) was utilized to establish the zeolite elemental composition. The results showed that investigated zeolite was classified as a sodium aluminum silicate and it was able to modify the rheological properties of the neat asphalt binder. The G*/sin{delta} parameter was affected by the zeolite presence, indicating better performance for the binders with zeolite. The results show that synthetic binders can partly replicate the rheological properties of conventional AB. Comparable complex modulus values was obtained. No significant difference was found in viscoelastic response, given by the phase angles as a function of both temperature and frequency. (author)

Structure of Rhodium in an Ultradispersed Rhodium/Alumina Catalyst as Studied by EXAFS and Other Technique

NARCIS (Netherlands)

Koningsberger, D.C.; Blik, H.F.J. van 't; Zon, J.B.A.D. van; Huizinga, T.; Vis, J.C.; Prins, R.

1985-01-01

The structure of rhodium in an ultradispersed 0.57 wt % Rh/y-Al,O, catalyst before and after CO adsorption was studied with extended X-ray absorption fine structure (EXAFS), X-ray photoelectron spectroscopy (XPS), electron spin resonance (ESR), temperature programmed reduction (TPR), CO infrared

Complexes of rhodium (I) and iridium (I) with mixed phosphorus-oxygen and phosphorus-nitrogen glands

Energy Technology Data Exchange (ETDEWEB)

Meintjies, E.; Singleton, E.; Schmutzler, R.; Sell, M.

1985-09-01

A series of four- and five-coordinate rhodium(I) and iridium(I) complexes of the type (MCl(cod)L) and (M(COD)L/sub 2/) sup(+)(M = Rh or Ir;cod = cycloocta-1,5-diene; L = P(C/sub 6/H/sub 4/OMe-o)/sub 3/, PMe/sub 2/(C/sub 6/H/sub 4/OMe-o), PPh/sub 2/(C/sub 6/H/sub 4/OMe-o), PPh/sub 2/-(C/sub 6/H/sub 4/NMe/sub 2/-o), PMe(C/sub 6/H/sub 4/OMe-o)/sub 2/ and PPh/sub 2/(C/sub 6/H/sub 4/OPr sup(i)-o)) have been prepared from the reactions of ((MCl(cod))/sub 2/) (M = Rh or Ir) with the appropriate stoichiometric amount of L in diethyl ether or methanol solution. N.M.R. evidence (/sup 1/H and /sup 13/C) is presented for non-chelation in the case of the ether ligands and chelation for the amine ligand. Thus, the complexes (MCl(cod)L)(L = ether ligand) are mononuclear square-planar species, whereas the amine ligand chelates to the metal atom, and a distorted trigonal bipyramidal structure is proposed. Attempts at displacing cod from the complexes (MCl(cod)L) with these ether and amine ligands, or with small phosphines, were unsuccessful. However, treatment of (MCl(cod)(P(C/sub 6/H/sub 4/OMe-o)/sub 3/))(M = Rh or Ir) with carbon monoxide gave (MCl(CO)/sub 2/ (P(C/sub 6/H/sub 4/OMe-o)/sub 3/)). In contrast, a disproportionation product, (RhCl(CNBu sup(t)/sub 2/(PPh/sub 2/ (C/sub 6/H/sub 4/OPr sup(i)-o))/sub 2/), was obtained from treatment of (RhCl(cod)(PPh/sub 2/(C/sub 6/H/sub 4/OPr sup(i)-o))) with t-butyl isocyanide. N.M.R. data (/sup 1/H and /sup 13/C) for the complexes are described.

Application of NKF-6 zeolite for the removal of U(VI) from aqueous solution

International Nuclear Information System (INIS)

Pengfei Zong; Hai Wang; Hui Pan; Yaolin Zhao; Chaohui He

2013-01-01

To better understand the application of NKF-6 zeolite as an adsorbent for the removal of U(VI) from radionuclides and heavy metal ions polluted water, herein, NKF-6 zeolite was employed to remove U(VI) at different experimental conditions. The influence of solid/liquid ratio, contact time, pH, ionic strength, humic substances and temperature on sorption of U(VI) to NKF-6 zeolite was investigated using batch technique under ambient conditions. The experimental results demonstrated that the sorption of U(VI) on NKF-6 zeolite was strongly dependent on pH. The sorption property of U(VI) was influenced by ionic strength at pH 7.0. The presence of fulvic acid or humic acid promoted the sorption of U(VI) on NKF-6 zeolite at low pH values while restrained the sorption at high pH values. The thermodynamic parameters (i.e., ΔS 0 , ΔH 0 , and ΔG 0 ) calculated from the temperature-dependent sorption isotherms demonstrated that the sorption process of U(VI) on NKF-6 zeolite was endothermic and spontaneous. At low pH values, the sorption of U(VI) was dominated by outer-sphere surface complexation and ion exchange with Na + /H + on NKF-6 zeolite surfaces, while inner-sphere surface complexation was the main sorption mechanism at high pH values. From the experimental results, one can conclude that NKF-6 zeolite can be used as a potential adsorbent for the preconcentration and solidification of U(VI) from large volumes of aqueous solutions. (author)

Isobutane/2-butene alkylation with zeolite Y without BrÆnsted acidity

OpenAIRE

Rosenbach Jr,Nilton; Mota,Claudio J. A.

2005-01-01

Alkylation of isobutane with 2-butene was performed on metal-exchanged Y zeolites, using an alkylchloride as carbocation initiator. The results indicated that, compared with a protonic zeolite, the deactivation was significantly slower and the production of trimethylpentanes was higher on the metal-exchanged zeolites. The metal cations act as Lewis acids, interacting with the chloride initiating the carbocationic reactions. The results also support the view that protonic sites on the catalyst...

Zeolites and clays behavior in presence of radioactive solutions

International Nuclear Information System (INIS)

Carrera Garcia, L.M.

1991-01-01

Natural aluminosilicates have found application as selective ion exchangers for radioactive cations, present in liquid wastes arising from nuclear facilities. Among severals cations and complex mixtures of them, Co is a common constituent of liquid radioactive wastes. Two types of zeolites (Y zeolite, and natural mexican erionite), and two types of clays (natural bentonite, and Al-expanded bentonite (Al-B) were used. Previous to the experiments, the zeolites and the natural bentonite were stabilized to their respective Na + form using 5N NaCl solution. 2Na + → 60 Co 2+ ion exchange kinetics in zeolites and clays was followed by gamma spectrometry using a NaCl-Co(NO 3 ) 2 isonormal solution (0.1N) labeled with 60 Co-Co(NO 3 ) 2 (100 μ Ci). Before and after experiments, the structural changes in the cristallinity of aluminosilicates were determined by X-ray diffraction. XRD analyzes show that the cristallinity of the aluminosilicates was not affected by ion exchange. After Co exchange the cell parameters were determined in all samples. The efficiency of zeolites, natual clays and expanded clays to remove cobalt ions from solutions depends on the ion echange capacity of the material. Results for long contacts time, 18 days, show that Co is more effectively removed by Y zeolite ( 4.07 wt %), followed by erionite (3.09 wt %), then bentonite ( 2.36 wt %) and finally expanded bentonite ( 0.70 wt %). In Y zeolite an unusual fast soportion uptake of 4.51 % wt Co was observed followed by a desorption process to 4.07 %. This effect is due to the different hydration degree of zeolites during the contact time between the zeolite and the 60 Co solution. In erionite the exchange is lower than in Y-zeolite, frist because the Si/Al ratio is higher for erionite than for Y-zeolite and second because K ions in erionite cannot be exchanged during the stabilization of erionite in 5N NaCl solution. The low exchange in expanded bentonite was expected because its cation exchange

Vapor phase carbonylation of dimethyl ether and methyl acetate with supported transition metal catalysts

International Nuclear Information System (INIS)

Shikada, T.; Fujimoto, K.; Tominaga, H.O.

1986-01-01

The synthesis of acetic acid (AcOH) from methanol (MeOH) and carbon monoxide has been performed industrially in the liquid phase using a rhodium complex catalyst and an iodide promoter. The selectivity to AcOH is more than 99% under mild conditions (175 0 C, 28 atm). The homogeneous rhodium catalyst has been also effective for the synthesis of acetic anhydride (Ac 2 O) by carbonylation of dimethyl ether (DME) or methyl acetate (AcOMe). However, rhodium is one of the most expensive metals and its proved reserves are quite limited. It is highly desired, therefore, to develop a new catalyst as a substitute for rhodium. The authors have already reported that nickel supported on active carbon exhibits an excellent activity for the vapor phase carbonylation of MeOh in the presence of iodide promoter and under moderately pressurized conditions. In addition, corrosive attack on reactors by iodide compounds is expected to be negligible in the vapor phase system. In the present work, vapor phase carbonylation of DME and AcOMe on nickel-active carbon (Ni/A.C.) and molybdenum-active carbon (Mo/A.C.) catalysts was studied

Design and characterization of chitosan/zeolite composite films — Effect of zeolite type and zeolite dose on the film properties

International Nuclear Information System (INIS)

Barbosa, Gustavo P.; Debone, Henrique S.; Severino, Patrícia; Souto, Eliana B.; Silva, Classius F. da

2016-01-01

Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance. - Highlights: • Zeolite/chitosan composite films were prepared by casting technique. • Micrographs showed slight difference according to the content and A-type zeolite. • The barrier properties of the films were suitable to the dressing application. • Film characterization suggested that zeolites interacted with the chitosan chain.

Design and characterization of chitosan/zeolite composite films — Effect of zeolite type and zeolite dose on the film properties

Energy Technology Data Exchange (ETDEWEB)

Barbosa, Gustavo P.; Debone, Henrique S. [Instituto de Ciências Ambientais, Químicas e Farmacêuticas, Universidade Federal de São Paulo, Diadema (Brazil); Severino, Patrícia [Universidade Tiradentes, Instituto de Tecnologia e Pesquisa, Aracaju (Brazil); Souto, Eliana B. [Department of Pharmaceutical Technology, Faculty of Pharmacy, University of Coimbra (FFUC), Pólo das Ciências da Saúde, Azinhaga de Santa Comba, 3000-548, Coimbra (Portugal); Center for Neuroscience and Cell Biology & Institute for Biomedical Imaging and Life Sciences (CNC-IBILI), University of Coimbra, Pólo das Ciências da Saúde, Azinhaga de Santa Comba, 3000-548, Coimbra (Portugal); Silva, Classius F. da, E-mail: cfsilva@unifesp.br [Instituto de Ciências Ambientais, Químicas e Farmacêuticas, Universidade Federal de São Paulo, Diadema (Brazil)

2016-03-01

Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance. - Highlights: • Zeolite/chitosan composite films were prepared by casting technique. • Micrographs showed slight difference according to the content and A-type zeolite. • The barrier properties of the films were suitable to the dressing application. • Film characterization suggested that zeolites interacted with the chitosan chain.

Rhodium-catalyzed C-H alkynylation of arenes at room temperature.

Science.gov (United States)

Feng, Chao; Loh, Teck-Peng

2014-03-03

The rhodium(III)-catalyzed ortho C-H alkynylation of non-electronically activated arenes is disclosed. This process features a straightforward and highly effective protocol for the synthesis of functionalized alkynes and represents the first example of merging a hypervalent iodine reagent with rhodium(III) catalysis. Notably, this reaction proceeds at room temperature, tolerates a variety of functional groups, and more importantly, exhibits high selectivity for monoalkynylation. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Bacterial biofilm supported on granular activated carbon and on natural zeolites- an application to wastewater treatment

OpenAIRE

Lameiras, Sandra Raquel de Vasconcelos; Quintelas, C.; Tavares, M. T.

2004-01-01

The removal of many heavy metals from industrial wastewater is one of the most important environmental problems to be solved today. The retention of this contaminants by a biofilm supported on granular activated carbon or on natural zeolites is one of the promising technologies for the reduction of this problem, because it is cheap and it removes a broad range of substances, heavy metals and organic compounds. This study aims the development of a system of two mini-columns in series ...

Removal of paraquat solution onto zeolite material

Science.gov (United States)

Sirival, Rujikarn; Patdhanagul, Nopbhasinthu; Preecharram, Sutthidech; Photharin, Somkuan

2018-04-01

The purpose of this research was to study the adsorption of paraquat herbicides onto zeolite Y materials by the batch method. Three adsorbents material: Zeolite-3, Zeolite-10, and Zeolite-100 were Si/Al ratio at 3.58, 8.57 and 154.37, respectively. The factors for adsorption of paraquat as follows, adsorption time, initial concentrations of paraquat, pH and adsorption isotherm were investigated. The results showed that zeolite-10 had higher adsorption capacity than zeolite-3 and zeolite-100. The appropriate conditions for adsorption were 24 h., Zeolite 0.1 g., Initial paraquat concentration 100 ppm at pH 6. The adsorption isotherm was found to correspond with Langmuir Isotherm and the maximum paraquat adsorption is 26.38 mg/g for zeolite-10, 21.41 mg/g and 9.60 mg/g for zeolite-3 and zeolite-100, respectively. The characterization of zeolite material with XRD, XRF and BET. Furthermore, the zeolite materials applied to remove other organic and inorganic wastewater.

Crystal structures of fac-tri?chlorido?tris?(tri?methyl?phosphane-?P)rhodium(III) monohydrate and fac-tri?chlorido?tris?(tri?methyl?phosphane-?P)rhodium(III) methanol hemisolvate: rhodium structures that are isotypic with their iridium analogs

OpenAIRE

Merola, Joseph S.; Franks, Marion A.

2015-01-01

The crystal structures of two solvates of fac-tri-chlorido-tris-(tri-methyl-phosphane-κP)rhodium(III) are reported, i.e. one with water in the crystal lattice, fac-[RhCl3(Me3P)3]·H2O, and one with methanol in the crystal lattice, fac-[RhCl3(Me3P)3]·0.5CH3OH. These rhodium compounds exhibit distorted octahedral coordination spheres at the metal and are isotypic with the analogous iridium compounds previously reported by us [Merola et al. (2013 ▶). Polyhedron, 54, 67-73]. Comparison is made bet...

{gamma} alumina- and HY zeolite-supported molybdenum catalysts: characterisation of the oxidic and sulfided phases; Catalyseurs a base de molybdene supporte sur alumine {gamma} et zeolithe HY: caracterisation des phases oxydes et sulfures

Energy Technology Data Exchange (ETDEWEB)

Plazenet, G

2001-10-01

Oxidic precursors of hydro-treatment catalysts (Co)Mo/alumina or zeolite were characterised by Raman spectroscopy, NMR and EXAFS at the Mo and Co K-edges. The formation of an Anderson-type alumino-molybdate compound upon impregnation of the support with an ammonium hepta-molybdate solution was confirmed for alumina, and also observed for the HY zeolitic support, with consumption of the amorphous alumina of the zeolite. In absence of the latter, ammonium hepta-molybdate precipitates. The species are conserved upon drying; upon calcination, the alumino-molybdate evolves into a surface aluminium molybdate type phase, whereas the hepta-molybdate transforms into MoO{sub 3}. The species formed upon impregnation are located in the inter-granular porosity whereas MoO{sub 3} vapor-condensation leads to formation of dimers located inside the zeolitic structure. The study of the cobalt-promoted precursors showed that the evolution of the molybdenum is the same in the case of co-impregnation preparation. Impregnation with cobalt-molybdate prevents the formation of the alumino-molybdate anion and thus enables the preservation of the Mo-Co interaction but, whatever the precursor, the leveling effect of the calcination-re-hydration steps was demonstrated. An EXAFS study at different sulfur coverages of the MoS{sub 2} platelets in the alumina-supported sulfided catalysts showed the limitations of EXAFS for size determination of MoS{sub 2} crystallites, a parameter that can be reached by AWAXS, which also conveys information about sheet-stacking. The EXAFS study of sulfided (Co)Mo/HY systems revealed incomplete sulfidation of the samples and the very high dispersion of the active phase. The absence of an observable Mo-Co interaction whatever the preparation of the promoted catalysts is consistent with the absence of promoting effect in toluene hydrogenation. (author)

Hydrogenation of hexene over platinum on alumina vs. platinum in a Na-Y zeolite

International Nuclear Information System (INIS)

Miner, R.S. Jr.; Ione, K.G.; Namba, S.; Turkevich, J.

1978-01-01

In order to study the efficacy of zeolites as supports, several platinum H--Y zeolites were prepared by ion exchanging an H--Y zeolite with Pt(NH 3 ) 4 Cl 2 and reducing these products with hydrazine hydrate (A, B, C). Another preparation was made by adsorbing 32-A platinum sol on the zeolite crystallites (D). These catalysts were studied for hydrogenation and isomerization of hexene-1, ethylene hydrogenation, hydrogen chemisorption, and poison titration. They were compared with monodisperse Pt (32 A diameter) on alumina. A marked difference was found between the behavior of hexene-1 with the platinum-in-zeolite and with the platinum-on-alumina

ADSORPSI POLUTAN ION DIKROMAT MENGGUNAKAN ZEOLIT ALAM TERMODIFIKASI AMINA (Adsorption of Dichromate Ions Pollutant Using Ammine Modified-Natural Zeolites

Directory of Open Access Journals (Sweden)

Eko Sri Kunarti

2015-11-01

Full Text Available ABSTRAK Kromium (VI merupakan polutan logam berat berbahaya bagi kesehatan dan lingkungan oleh karena itu pengambilan ion Cr(VI dalam air penting dilakukan untuk mengatasi pencemaran lingkungan. Proses adsorpsi merupakan salah satu teknik sederhana yang dapat digunakan untuk pengambilan ion logam. Pada penelitian ini telah dilakukan kajian adsorpsi ion dikromat sebagai model limbah Cr(VI dalam air menggunakan adsorben zeolit alam termodifikasi amina. Penelitian diawali dengan preparasi adsorben zeolit alam termodifikasi amina. Preparasi dimulai dengan pencucian zeolit alam menggunakan akuades, kemudian refluks zeolit alam menggunakan HCl 3M. Zeolit hasil refluks selanjutnya dimodifikasi menggunakan garam ammonium kuarterner, N-cethyl-N,N,N-trimethylammonium bromide (CTAB dan amina primer, propilamin (PA. Zeolit alam (Z, zeolit teraktivasi asam (ZA dan zeolit hasil modifikasi amina selanjutnya digunakan sebagai adsorben untuk adsorpsi anion dikromat. Karakterisasi adsorben dilakukan dengan mengunakan metode spektroskopi infaramerah dan difraksi sinar-X, sedangkan jumlah anion dikromat yang teradsorpsi dianalisis dengan spektroskopi serapan atom. Hasil penelitian menunjukkan bahwa sampel zeolit mengandung mineral klinoptilolit, mordernit dan kuarsa. Struktur zeolit tidak mengalami kerusakan oleh perlakuan termal dan perlakuan kimia. Modifikasi zeolit meningkatkan efisiensi adsorpsi zeolit alam. Ion dikromat dapat teradsorpsi dengan lebih baik oleh zeolit termodifikasi amina daripada zeolit teraktivasi asam dan zeolit tanpa modifikasi, dengan kemampuan adsorpsi zeolit termodifikasi CTAB (CTAB-Z lebih besar daripada zeolit termodifikasi propilamin (PA-Z. Adsorpsi ion dikromat pada adsorben zeolit berlangsung baik dengan urutan CTAB-Z > PA-Z > ZA > Z, dengan kemampuan adsorpsi masing-masing sebesar 1,96; 1,74; 0,90 dan 0,48 mg/g. Adsorpsi anion dikromat oleh zeolit termodifikasi CTAB merupakan adsorpsi kimia (kemisorpsi dengan energi adsorpsi sebesar

Rhodium-catalyzed chemo-, regio-, and enantioselective addition of 2-pyridones to terminal allenes.

Science.gov (United States)

Li, Changkun; Kähny, Matthias; Breit, Bernhard

2014-12-08

A rhodium-catalyzed chemo-, regio-, and enantioselective addition of 2-pyridones to terminal allenes to give branched N-allyl 2-pyridones is reported. Preliminary mechanistic studies support the hypothesis that the reaction was initiated from the more acidic 2-hydroxypyridine form, and the initial kinetic O-allylation product was finally converted into the thermodynamically more stable N-allyl 2-pyridones. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydrothermally grown zeolite crystals

International Nuclear Information System (INIS)

Durrani, S.K.; Qureshi, A.H.; Hussain, M.A.; Qazi, N.K.

2009-01-01

The aluminium-deficient and ferrosilicate zeolite-type materials were synthesized by hydrothermal process at 150-170 degree C for various periods of time from the mixtures containing colloidal reactive silica, sodium aluminate, sodium hydroxide, iron nitrate and organic templates. Organic polycation templates were used as zeolite crystal shape modifiers to enhance relative growth rates. The template was almost completely removed from the zeolite specimens by calcination at 550 degree C for 8h in air. Simultaneous thermogravimetric (TG) and differential thermal analysis (DTA) was performed to study the removal of water molecules and the amount of organic template cations occluded inside the crystal pore of zeolite framework. The 12-13% weight loss in the range of (140-560 degree C) was associated with removal of the (C/sub 3/H/sub 7/)/sub 4/ N+ cation and water molecules. X-ray diffraction (XRD) analysis and scanning electron microscope (SEM) techniques were employed to study the structure, morphology and surface features of hydrothermally grown aluminium-deficient and ferrosilicate zeolite-type crystals. In order to elucidate the mode of zeolite crystallization the crystallinity and unit cell parameters of the materials were determined by XRD, which are the function of Al and Fe contents of zeolites. (author)

Mesoporous Zeolite Single Crystals for Catalytic Hydrocarbon Conversion

DEFF Research Database (Denmark)

Schmidt, I.; Christensen, Claus H.; Kustova, Marina

2005-01-01

Recently, mesoporous zeolite single crystals were discovered. They constitute a novel family of materials that features a combined micropore and mesopore architecture within each individual crystal. Here, we briefly summarize recent catalytic results from cracking and isomerization of alkalies......, alkylation of aromatics and present new results on isomerization of aromatics. Specifically, the shape-selective isomerization of meta-xylenc into para-xylene and ortho-xylene is studied. In all these reactions, rnesoporous zeolite single crystals prove to be unique catalysts since they provide easy...... transport to and from active sites and at the same time maintain the shape-selectivity required. Thus, all these results support the idea that the beneficial effect of the mesopores system in the mesoporous zeolite single crystals call be solely attributed to enhanced mass transport....

Characterization and antibacterial activity of silver exchanged regenerated NaY zeolite from surfactant-modified NaY zeolite

Energy Technology Data Exchange (ETDEWEB)

Salim, Mashitah Mad; Malek, Nik Ahmad Nizam Nik, E-mail: niknizam@fbb.utm.my

2016-02-01

The antibacterial activity of regenerated NaY zeolite (thermal treatment from cetyltrimethyl ammonium bromide (CTAB)-modified NaY zeolite and pretreatment with Na ions) loaded with silver ions were examined using the broth dilution minimum inhibitory concentration (MIC) method against Escherichia coli (E. coli ATCC 11229) and Staphylococcus aureus (S. aureus ATCC 6538). X-ray diffraction (XRD), attenuated total reflectance–Fourier transform infrared (ATR–FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) and chemical elemental analyses were used to characterize the regenerated NaY and AgY zeolites. The XRD patterns indicated that the calcination and addition of silver ions on regenerated NaY zeolite did not affect the structure of the regenerated NaY zeolite as the characteristic peaks of the NaY zeolite were retained, and no new peaks were observed. The regenerated AgY zeolite showed good antibacterial activity against both bacteria strains in distilled water, and the antibacterial activity of the samples increased with increasing Ag loaded on the regenerated AgY zeolite; the regenerated AgY zeolite was more effective against E. coli than S. aureus. However, the antibacterial activity of the regenerated AgY was not effective in saline solution for both bacteria. The study showed that CTAB-modified NaY zeolite materials could be regenerated to NaY zeolite using thermal treatment (550 °C, 5 h) and this material has excellent performance as an antibacterial agent after silver ions loading. - Highlights: • Thermal treatment was used to regenerate surfactant modified zeolite. • The regenerated NaY zeolite formed was added with different silver loadings. • Regenerated AgY zeolite was tested for antibacterial activity on E. coli and S. aureus. • The antibacterial activity increased with increased of the amount of silver loadings. • The zeolite structure did not change with thermal and modification

Characterization and antibacterial activity of silver exchanged regenerated NaY zeolite from surfactant-modified NaY zeolite

International Nuclear Information System (INIS)

Salim, Mashitah Mad; Malek, Nik Ahmad Nizam Nik

2016-01-01

The antibacterial activity of regenerated NaY zeolite (thermal treatment from cetyltrimethyl ammonium bromide (CTAB)-modified NaY zeolite and pretreatment with Na ions) loaded with silver ions were examined using the broth dilution minimum inhibitory concentration (MIC) method against Escherichia coli (E. coli ATCC 11229) and Staphylococcus aureus (S. aureus ATCC 6538). X-ray diffraction (XRD), attenuated total reflectance–Fourier transform infrared (ATR–FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) and chemical elemental analyses were used to characterize the regenerated NaY and AgY zeolites. The XRD patterns indicated that the calcination and addition of silver ions on regenerated NaY zeolite did not affect the structure of the regenerated NaY zeolite as the characteristic peaks of the NaY zeolite were retained, and no new peaks were observed. The regenerated AgY zeolite showed good antibacterial activity against both bacteria strains in distilled water, and the antibacterial activity of the samples increased with increasing Ag loaded on the regenerated AgY zeolite; the regenerated AgY zeolite was more effective against E. coli than S. aureus. However, the antibacterial activity of the regenerated AgY was not effective in saline solution for both bacteria. The study showed that CTAB-modified NaY zeolite materials could be regenerated to NaY zeolite using thermal treatment (550 °C, 5 h) and this material has excellent performance as an antibacterial agent after silver ions loading. - Highlights: • Thermal treatment was used to regenerate surfactant modified zeolite. • The regenerated NaY zeolite formed was added with different silver loadings. • Regenerated AgY zeolite was tested for antibacterial activity on E. coli and S. aureus. • The antibacterial activity increased with increased of the amount of silver loadings. • The zeolite structure did not change with thermal and modification

Ultrasound-assisted dealumination of zeolite Y

Indian Academy of Sciences (India)

zeolite Y the Si/Al molar ratio plays an important role in solid acidity .... determined using electron microprobe X-ray analysis. (EMPA) We also ... Surface area (m2/g) Pore Volume (cm3/g) XRD calculation .... for financial support for this work.

Risk assessment for the transportation of radioactive zeolite liners

International Nuclear Information System (INIS)

1982-01-01

The risk is estimated for the shipment of radioactive zeolite liners in support of the Zeolite Vitrification Demonstration Program currently underway at Pacific Northwest Laboratory under the sponsorship of the US Department of Energy. This program will establish the feasibility of zeolite vitrification as an effective means of immobilizing high-specific-activity wastes. In this risk assessment, it is assumed that two zeolite liners, each loaded around July 1, 1981 to 60,000 Ci, will be shipped by truck around January 1, 1982. However, to provide a measure of conservatism, each liner is assumed to initially hole 70,000 Ci, with the major radioisotopes as follow: 90 Sr = 3000 Ci, 134 Cs = 7000 Ci, 137 Cs = 60,000 Ci. Should shipment take place with essentially no delay after initial loading (regardless of loading date), the shipment loading would be only 2.7% higher than that for the assumed six-month delay. This would negligibly affect the overall risk. As a result of this risk assessment, it is concluded that the transport of the radioactive zeolite liners from TMI to PNL by truck can be conducted at an insignificant level of risk to the public

Rhodium-Catalyzed Dehydrogenative Borylation of Cyclic Alkenes

Science.gov (United States)

Kondoh, Azusa; Jamison, Timothy F.

2010-01-01

A rhodium-catalyzed dehydrogenative borylation of cyclic alkenes is described. This reaction provides direct access to cyclic 1-alkenylboronic acid pinacol esters, useful intermediates in organic synthesis. Suzuki-Miyaura cross-coupling applications are also presented. PMID:20107646

Process for producing zeolite adsorbent and process for treating radioactive liquid waste with the zeolite adsorbent

International Nuclear Information System (INIS)

Motojima, K.; Kawamura, F.

1984-01-01

Zeolite is contacted with an aqueous solution containing at least one of copper, nickel, cobalt, manganese and zinc salts, preferably copper and nickel salts, particularly preferably copper salt, in such a form as sulfate, nitrate, or chloride, thereby adsorbing the metal on the zeolite in its pores by ion exchange, then the zeolite is treated with a water-soluble ferrocyanide compound, for example, potassium ferrocyanide, thereby forming metal ferrocyanide on the zeolite in its pores. Then, the zeolite is subjected to ageing treatment, thereby producing a zeolite adsorbent impregnated with metal ferrocyanide in the pores of zeolite. The adsorbent can selectively recover cesium with a high percent cesium removal from a radioactive liquid waste containing at least radioactive cesium, for example, a radioactive liquid waste containing cesium and such coexisting ions as sodium, magnesium, calcium and carbonate ions at the same time at a high concentration. The zeolite adsorbent has a stable adsorbability for a prolonged time

Conclusive evidence on the mechanism of the rhodium-mediated decyanative borylation.

Science.gov (United States)

Esteruelas, Miguel A; Oliván, Montserrat; Vélez, Andrea

2015-09-30

The stoichiometric reactions proposed in the mechanism of the rhodium-mediated decyanative borylation have been performed and all relevant intermediates isolated and characterized including their X-ray structures. Complex RhCl{xant(P(i)Pr2)2} (1, xant(P(i)Pr2)2 = 9,9-dimethyl-4,5-bis(diisopropylphosphino)xanthene) reacts with bis(pinacolato)diboron (B2pin2), in benzene, to give the rhodium(III) derivative RhHCl(Bpin){xant(P(i)Pr2)2} (4) and PhBpin. The reaction involves the oxidative addition of B2pin2 to 1 to give RhCl(Bpin)2{xant(P(i)Pr2)2}, which eliminates ClBpin generating Rh(Bpin){xant(P(i)Pr2)2} (2). The reaction of the latter with the solvent yields PhBpin and the monohydride RhH{xant(P(i)Pr2)2} (6), which adds the eliminated ClBpin. Complex 4 and its catecholboryl counterpart RhHCl(Bcat){xant(P(i)Pr2)2} (7) have also been obtained by oxidative addition of HBR2 to 1. Complex 2 is the promoter of the decyanative borylation. Thus, benzonitrile and 4-(trifluoromethyl)benzonitrile insert into the Rh-B bond of 2 to form Rh{C(R-C6H4)═NBpin}{xant(P(i)Pr2)2} (R = H (8), p-CF3 (9)), which evolve into the aryl derivatives RhPh{xant(P(i)Pr2)2} (3) and Rh(p-CF3-C6H4){xant(P(i)Pr2)2} (10), as a result of the extrusion of CNBpin. The reactions of 3 and 10 with B2pin2 yield the arylBpin products and regenerate 2.

Rapid synthesis of beta zeolites

Science.gov (United States)

Fan, Wei; Chang, Chun -Chih; Dornath, Paul; Wang, Zhuopeng

2015-08-18

The invention provides methods for rapidly synthesizing heteroatom containing zeolites including Sn-Beta, Si-Beta, Ti-Beta, Zr-Beta and Fe-Beta. The methods for synthesizing heteroatom zeolites include using well-crystalline zeolite crystals as seeds and using a fluoride-free, caustic medium in a seeded dry-gel conversion method. The Beta zeolite catalysts made by the methods of the invention catalyze both isomerization and dehydration reactions.

Separation of BSA through FAU-type zeolite ceramic composite membrane formed on tubular ceramic support: Optimization of process parameters by hybrid response surface methodology and biobjective genetic algorithm.

Science.gov (United States)

Vinoth Kumar, R; Ganesh Moorthy, I; Pugazhenthi, G

2017-08-09

In this study, Faujasite (FAU) zeolite was coated on low-cost tubular ceramic support as a separating layer through hydrothermal route. The mixture of silicate and aluminate solutions was used to create a zeolitic separation layer on the support. The prepared zeolite ceramic composite membrane was characterized using X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), particle size distribution (PSD), field emission scanning electron microscopy (FESEM), and zeta potential measurements. The porosity of ceramic support (53%) was reduced by the deposition of FAU (43%) zeolite layer. The pore size and water permeability of the membrane were evaluated as 0.179 µm and 1.62 × 10 -7  m 3 /m 2  s kPa, respectively, which are lower than that of the support (pore size of 0.309 µm and water permeability of 5.93 × 10 -7  m 3 /m 2  s kPa). The permeate flux and rejection potential of the prepared membrane were evaluated by microfiltration of bovine serum albumin (BSA). To study the influences of three independent variables such as operating pressure (68.94-275.79 kPa), concentration of BSA (100-500 ppm), and solution pH (2-4) on permeate flux and percentage of rejection, the response surface methodology (RSM) was used. The predicted models for permeate flux and rejection were further subjected to biobjective genetic algorithm (GA). The hybrid RSM-GA approach resulted in a maximum permeate flux of 2.66 × 10 -5  m 3 /m 2  s and BSA rejection of 88.02%, at which the optimum conditions were attained as 100 ppm BSA concentration, 2 pH solution, and 275.79 kPa applied pressure. In addition, the separation efficiency was compared with other membranes applied for BSA separation to know the potential of the fabricated FAU zeolite ceramic composite membrane.

Rhodium-catalysed syn-carboamination of alkenes via a transient directing group.

Science.gov (United States)

Piou, Tiffany; Rovis, Tomislav

2015-11-05

Alkenes are the most ubiquitous prochiral functional groups--those that can be converted from achiral to chiral in a single step--that are accessible to synthetic chemists. For this reason, difunctionalization reactions of alkenes (whereby two functional groups are added to the same double bond) are particularly important, as they can be used to produce highly complex molecular architectures. Stereoselective oxidation reactions, including dihydroxylation, aminohydroxylation and halogenation, are well established methods for functionalizing alkenes. However, the intermolecular incorporation of both carbon- and nitrogen-based functionalities stereoselectively across an alkene has not been reported. Here we describe the rhodium-catalysed carboamination of alkenes at the same (syn) face of a double bond, initiated by a carbon-hydrogen activation event that uses enoxyphthalimides as the source of both the carbon and the nitrogen functionalities. The reaction methodology allows for the intermolecular, stereospecific formation of one carbon-carbon and one carbon-nitrogen bond across an alkene, which is, to our knowledge, unprecedented. The reaction design involves the in situ generation of a bidentate directing group and the use of a new cyclopentadienyl ligand to control the reactivity of rhodium. The results provide a new way of synthesizing functionalized alkenes, and should lead to the convergent and stereoselective assembly of amine-containing acyclic molecules.

UTL zeolite and the way beyond

Czech Academy of Sciences Publication Activity Database

Shvets, O. V.; Nachtigall, P.; Roth, Wieslaw Jerzy; Čejka, Jiří

2013-01-01

Roč. 182, DEC 2013 (2013), s. 229-238 ISSN 1387-1811 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : zeolite UTL * synthesis * hydrolysis Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.209, year: 2013

Synthesis of 4A zeolites from kaolin for obtaining 5A zeolites through ionic exchange for adsorption of arsenic

International Nuclear Information System (INIS)

Resmini Melo, Carolina; Gracher Riella, Humberto; Cabral Kuhnen, Nivaldo; Angioletto, Elidio; Melo, Aline Resmini; Bernardin, Adriano Michael; Rocha, Marcio Roberto da; Silva, Luciano da

2012-01-01

Highlights: ► We synthesize 4A zeolite from kaolin by hydrothermal reaction with sodium hydroxide. ► The 4A zeolite synthesized underwent ion exchange with calcium ions, with different parameters, to obtain 5A zeolites. ► The best 4A zeolite obtained was used as adsorbent material for arsenic ions. ► The results showed that the 5A zeolite material obtained is a good adsorber of heavy ions. - Abstract: The synthesis of adsorbing zeolite materials requires fine control of the processing variables. There are distinct process variable settings for obtaining specific desired types of zeolites. The intent of this study was to obtain 4A zeolites from kaolin in order to obtain 5A zeolites through ionic exchange with the previously synthesized zeolite. This zeolite 5A was used as an adsorbent for arsenic ions. The results obtained were satisfactory.

Synthesis and characterization of rhodium sulfide nanoparticles and thin films

International Nuclear Information System (INIS)

Sosibo, Ndabenhle M.; Revaprasadu, Neerish

2008-01-01

The synthesis and characterization of a rhodium complex, [Rh(S 2 CNEt 2 ) 2 ] is described. The complex was thermolysed at a high temperature (280 deg. C) in the presence of capping agent, hexadecylamine (HDA) to form Rh 2 S 3 nanoparticles. Rod-shaped Rh 2 S 3 nanoparticles with an average length of 26.7 nm and an average breadth of 7.8 nm were synthesized. The complex was also used as a single molecule precursor for the deposition of Rh 2 S 3 thin films on a glass substrate at 350 deg. C and 450 deg. C using the Aerosol Assisted Chemical Vapour Deposition (AACVD) technique. The resultant thin films showed temperature dependent morphologies and showed (0 2 2), (4 1 1) and (6 1 1) lattice planes characteristic of to the orthorhombic Rh 2 S 3 phase. X-ray diffraction and scanning electron microscopy techniques were used to characterize the films

Synthesis and characterization of rhodium sulfide nanoparticles and thin films

Energy Technology Data Exchange (ETDEWEB)

Sosibo, Ndabenhle M. [Department of Chemistry, University of Zululand, Private Bag X1001, KwaDlangezwa 3886 (South Africa); Revaprasadu, Neerish [Department of Chemistry, University of Zululand, Private Bag X1001, KwaDlangezwa 3886 (South Africa)], E-mail: nrevapra@pan.uzulula.za

2008-05-15

The synthesis and characterization of a rhodium complex, [Rh(S{sub 2}CNEt{sub 2}){sub 2}] is described. The complex was thermolysed at a high temperature (280 deg. C) in the presence of capping agent, hexadecylamine (HDA) to form Rh{sub 2}S{sub 3} nanoparticles. Rod-shaped Rh{sub 2}S{sub 3} nanoparticles with an average length of 26.7 nm and an average breadth of 7.8 nm were synthesized. The complex was also used as a single molecule precursor for the deposition of Rh{sub 2}S{sub 3} thin films on a glass substrate at 350 deg. C and 450 deg. C using the Aerosol Assisted Chemical Vapour Deposition (AACVD) technique. The resultant thin films showed temperature dependent morphologies and showed (0 2 2), (4 1 1) and (6 1 1) lattice planes characteristic of to the orthorhombic Rh{sub 2}S{sub 3} phase. X-ray diffraction and scanning electron microscopy techniques were used to characterize the films.

Electrode-Modified Zeolites - Electrode Microstructures Contained in and on a Heterogeneous Catalyst

Science.gov (United States)

1988-07-15

zeolite Type Y and Pt supported on gamma-alumina. The electrolytic response of zeolite-supported Pt in the absence of added electrolyte salt for water or...character of metals at sizes where’ bulk metallic properties may not be exhibited. Furthermore, electrolyses are now allowed using loadings of catalysts which...in water until the filtrate tested negatively for Cl with AgNO 3; PtY was then dried a- 135 C. Equilibrium exchnge occurs at these low weight

Snapshot analysis for rhodium fixed incore detector using BEACON methodology

International Nuclear Information System (INIS)

Cha, Kyoon Ho; Choi, Yu Sun; Lee, Eun Ki; Park, Moon Ghu; Morita, Toshio; Heibel, Michael D.

2004-01-01

The purpose of this report is to process the rhodium detector data of the Yonggwang nuclear unit 4 cycle 5 core for the measured power distribution by using the BEACON methodology. Rhodium snapshots of the YGN 4 cycle 5 have been analyzed by both BEACON/SPINOVA and CECOR to compare the results of both codes. By analyzing a large number of snapshots obtained during normal plant operation. Reviewing the results of this analysis, the BEACON/SPNOVA can be used for the snapshot analysis of Korean Standard Nuclear Power (KSNP) plants

Direct Synthesis of 5-Aryl Barbituric Acids by Rhodium(II)-Catalyzed Reactions of Arenes with Diazo Compounds**

Science.gov (United States)

Best, Daniel; Burns, David J; Lam, Hon Wai

2015-01-01

A commercially available rhodium(II) complex catalyzes the direct arylation of 5-diazobarbituric acids with arenes, allowing straightforward access to 5-aryl barbituric acids. Free N—H groups are tolerated on the barbituric acid, with no complications arising from N—H insertion processes. This method was applied to the concise synthesis of a potent matrix metalloproteinase (MMP) inhibitor. PMID:25959544

The influence of pH on the in vitro permeation of rhodium through human skin.

Science.gov (United States)

Jansen Van Rensburg, Sané; Franken, Anja; Du Plessis, Jeanetta; Du Plessis, Johannes Lodewykus

2017-06-01

Workers in precious metals refineries are at risk of exposure to salt compounds of the platinum group metals through inhalation, as well as through the skin. Rhodium salt permeation through the skin has previously been proven using rhodium trichloride (RhCl 3 ) dissolved in synthetic sweat at a pH of 6.5. However, the skin surface pH of refinery workers may be lower than 6.5. The aim of this study was to investigate the influence of pH 6.5 and 4.5 on the in vitro permeation of rhodium through intact Caucasian skin using Franz diffusion cells. A concentration of 0.3 mg mL -1 rhodium was used and analyses were performed using inductively coupled plasma mass spectrometry and inductively coupled plasma optical emission spectrometry. Results indicated a cumulative increase in permeation over 24 h. Rhodium permeation after 12 h was significantly greater at pH 4.5 (1.56 ± 0.24 ng cm -2 ) than at 6.5 (0.85 ± 0.13 ng cm -2 ; p = 0.02). At both pH levels, there was a highly significant difference ( p rhodium remaining in the skin (1428.68 ± 224.67 ng cm -2 at pH 4.5 and 1029.90 ± 115.96 ng cm -2 at pH 6.5) and the mass that diffused through (0.88 ± 0.17 ng cm -2 at pH 4.5 and 0.62 ± 0.10 ng cm -2 at pH 6.5). From these findings, it is evident that an acidic working environment or low skin surface pH may enhance permeation of rhodium salts, contributing to sensitization and adverse health effects.

Design and characterization of chitosan/zeolite composite films--Effect of zeolite type and zeolite dose on the film properties.

Science.gov (United States)

Barbosa, Gustavo P; Debone, Henrique S; Severino, Patrícia; Souto, Eliana B; da Silva, Classius F

2016-03-01

Chitosan films can be used as wound dressings for the treatment of chronic wounds and severe burns. The antimicrobial properties of these films may be enhanced by the addition of silver. Despite the antimicrobial activity of silver, several studies have reported the cytotoxicity as a factor limiting its biomedical applications. This problem may, however, be circumvented by the provision of sustained release of silver. Silver zeolites can be used as drug delivery platforms to extend the release of silver. The objective of this study was to evaluate the addition of clinoptilolite and A-type zeolites in chitosan films. Sodium zeolites were initially subjected to ion-exchange in a batch reactor. Films were prepared by casting technique using a 2% w/w chitosan solution and two zeolite doses (0.1 or 0.2% w/w). Films were characterized by thermal analysis, color analysis, scanning electron microscopy, X-ray diffraction, and water vapor permeation. The results showed that films present potential for application as dressing. The water vapor permeability is one of the main properties in wound dressings, the best results were obtained for A-type zeolite/chitosan films, which presented a brief reduction of this property in relation to zeolite-free chitosan film. On the other hand, the films containing clinoptilolite showed lower water vapor permeation, which may be also explained by the best distribution of the particles into the polymer which also promoted greater thermal resistance.

Mobil/Badger to market zeolite-based cumene technology

International Nuclear Information System (INIS)

Rotman, D.

1993-01-01

Badger (Cambridge, MA) and Mobil (Fairfax, VA) are ready to jointly license a new cumene technology that they say achieves higher yields and product purity than existing processes. The zeolite-based technology is scheduled to be introduced at next month's DeWitt Petrochemical Review in Houston. The Mobil/Badger technology aims to challenge the dominant position of UOP's (Des Plaines, IL) solid phosphoric acid (SPA) catalyst process - which accounts for 80%-90% of the world's cumene production. In addition, Monsanto/Kellogg's aluminum chloride-based technology has gained significant momentum since its introduction in the 1980s. And late last year, ABB Lummus Crest (Bloomfield, NJ) also began marketing a zeolite-based cumene technology. While all the technologies make cumene via the alkylation of benzene with propylene, the Mobil/Badger process uses a zeolite-containing catalyst designed by Mobil to selectively catalyze the benzene/propylene reaction, avoiding unwanted propylene oligomerization. Because the olefin reactions are so fast, says Frank A. Demers, Badger's v.p./technology development and marketing, other zeolite technologies are forced to use complex reactor arrangements to stop the propylene-propylene reactions. However, he says, 'Mobil has designed a catalyst that wants to react benzene with propylene to make cumene.'

Theoretical investigation of layered zeolite frameworks: Interaction between IPC-1P layers derived from zeolite UTL

Czech Academy of Sciences Publication Activity Database

Grajciar, L.; Bludský, Ota; Roth, Wieslaw Jerzy; Nachtigall, P.

2013-01-01

Roč. 204, Apr 15 (2013), s. 15-21 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388963 ; RVO:61388955 Keywords : layered zeolites * density functional theory * hydrogen bonding * structure Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.309, year: 2013

Hydrodeoxygenation of fatty acid esters catalyzed by Ni on nano-sized MFI type zeolites

Energy Technology Data Exchange (ETDEWEB)

Schreiber, Moritz W.; Rodriguez-Niño, Daniella; Gutiérrez, Oliver Y.; Lercher, Johannes A.

2016-01-01

The impact of support morphology and composition on the intrinsic activity of Ni supported on MFI-type zeolite was explored in the hydrodeoxygenation of methyl stearate, tristearate, and algae oil (mixture of triglycerides). The nano-sized structure of the support (self-pillared nanosheets) is beneficial for the activity of the catalysts. Higher Ni dispersion and concomitant higher reaction rates were obtained on nano-structured supports than on zeolite with conventional morphology. Rates normalized to accessible Ni atoms (TOF), however, varied little with support morphology. Acidity of the support increases the rate of Ni-catalyzed C-O hydrogenolysis per surface metal site.

Selective methane chlorination to methyl chloride by zeolite Y-based catalysts

Science.gov (United States)

Joo, Hyeonho; Kim, Daeho; Lim, Kwang Soo; Choi, Yong Nam; Na, Kyungsu

2018-03-01

The CH4 chlorination over Y zeolites was investigated to produce CH3Cl in a high yield. Three different catalytic systems based on Y zeolite were tested for enhancement of CH4 conversion and CH3Cl selectivity: (i) HY zeolites in H+-form having various Si/Al ratios, (ii) Pt/HY zeolites supporting Pt metal nanoparticles, (iii) Pt/NaY zeolites in Na+-form supporting Pt metal nanoparticles. The reaction was carried out using the gas mixture of CH4 and Cl2 with the respective flow rates of 15 and 10 mL min-1 at 300-350 °C using a fixed-bed reactor under a continuous gas flow condition (gas hourly space velocity = 3000 mL g-1 h-1). Above the reaction temperature of 300 °C, the CH4 chlorination is spontaneous even in the absence of catalyst, achieving 23.6% of CH4 conversion with 73.4% of CH3Cl selectivity. Under sufficient supplement of thermal energy, Cl2 molecules can be dissociated to two chlorine radicals, which triggered the C-H bond activation of CH4 molecule and thereby various chlorinated methane products (i.e., CH3Cl, CH2Cl2, CHCl3, CCl4) could be produced. When the catalysts were used under the same reaction condition, enhancement in the CH4 conversion was observed. The Pt-free HY zeolite series with varied Si/Al ratios gave around 27% of CH4 conversion, but there was a slight decrease in CH3Cl selectivity with about 64%. Despite the difference in acidity of HY zeolites having different Si/Al ratios, no prominent effect of the Si/Al ratios on the catalytic performance was observed. This suggests that the catalytic contribution of HY zeolites under the present reaction condition is not strong enough to overcome the spontaneous CH4 chlorination. When the Pt/HY zeolite catalysts were used, the CH4 conversion reached further up to 30% but the CH3Cl selectivity decreased to 60%. Such an enhancement of CH4 conversion could be attributed to the strong catalytic activity of HY and Pt/HY zeolite catalysts. However, both catalysts induced the radical cleavage of Cl2

Catalytic Fast Pyrolysis of Cellulose Using Nano Zeolite and Zeolite/Matrix Catalysts in a GC/Micro-Pyrolyzer.

Science.gov (United States)

Lee, Kyong-Hwan

2016-05-01

Cellulose, as a model compound of biomass, was catalyzed over zeolite (HY,.HZSM-5) and zeolite/matrix (HY/Clay, HM/Clay) in a GC/micro-pyrolyzer at 500 degrees C, to produce the valuable products. The catalysts used were pure zeolite and zeolite/matrix including 20 wt% matrix content, which were prepared into different particle sizes (average size; 0.1 mm, 1.6 mm) to study the effect of the particle size of the catalyst for the distribution of product yields. Catalytic pyrolysis had much more volatile products as light components and less content of sugars than pyrolysis only. This phenomenon was strongly influenced by the particle size of the catalyst in catalytic fast pyrolysis. Also, in zeolite and zeolite/matrix catalysts the zeolite type gave the dominant impact on the distribution of product yields.

Thermal behavior of natural zeolites

International Nuclear Information System (INIS)

Bish, D.L.

1993-01-01

Thermal behavior of natural zeolites impacts their application and identification and varies significantly from zeolite to zeolite. Zeolites evolve H 2 0 upon heating, but recent data show that distinct ''types'' of water (e.g., loosely bound or tightly bound zeolitic water) do not exist. Rather water is bound primarily to extra-framework cations with a continuum of energies, giving rise to pseudocontinuous loss of water accompanied by a dynamic interaction between remaining H 2 0 molecules and extra-framework cations. These interactions in the channels of zeolites give rise to dehydration dependent on the extra-framework cation, in addition to temperature and water vapor pressure. The dehydration reaction and the extra-framework cation also affect the thermal expansion/contraction. Most zeolites undergo dehydration-induced contractions that may be anisotropic, although minor thermal expansion can be seen with some zeolites. Such contractions can be partially or completely irreversible if they involve modifications of the tetrahedral framework and/or if rehydration is sluggish. Thermally induced structural modifications are also driven initially by dehydration and the concomitant contraction and migration of extra-framework cations. Contraction is accommodated by rotations of structural units and tetrahedral cation-oxygen linkages may break. Thermal reactions that involve breaking of tetrahedral cation-oxygen bonds markedly irreversible and may be kinetically limited, producing large differences between short- and long-term heating

Zeolite Membrane Reactor for Water Gas Shift Reaction for Hydrogen Production

Energy Technology Data Exchange (ETDEWEB)

Lin, Jerry Y.S. [Arizona State Univ., Mesa, AZ (United States)

2013-01-29

Gasification of biomass or heavy feedstock to produce hydrogen fuel gas using current technology is costly and energy-intensive. The technology includes water gas shift reaction in two or more reactor stages with inter-cooling to maximize conversion for a given catalyst volume. This project is focused on developing a membrane reactor for efficient conversion of water gas shift reaction to produce a hydrogen stream as a fuel and a carbon dioxide stream suitable for sequestration. The project was focused on synthesizing stable, hydrogen perm-selective MFI zeolite membranes for high temperature hydrogen separation; fabricating tubular MFI zeolite membrane reactor and stable water gas shift catalyst for membrane reactor applications, and identifying experimental conditions for water gas shift reaction in the zeolite membrane reactor that will produce a high purity hydrogen stream. The project has improved understanding of zeolite membrane synthesis, high temperature gas diffusion and separation mechanisms for zeolite membranes, synthesis and properties of sulfur resistant catalysts, fabrication and structure optimization of membrane supports, and fundamentals of coupling reaction with separation in zeolite membrane reactor for water gas shift reaction. Through the fundamental study, the research teams have developed MFI zeolite membranes with good perm-selectivity for hydrogen over carbon dioxide, carbon monoxide and water vapor, and high stability for operation in syngas mixture containing 500 part per million hydrogen sulfide at high temperatures around 500°C. The research teams also developed a sulfur resistant catalyst for water gas shift reaction. Modeling and experimental studies on the zeolite membrane reactor for water gas shift reaction have demonstrated the effective use of the zeolite membrane reactor for production of high purity hydrogen stream.

Epitaxially Grown Layered MFI–Bulk MFI Hybrid Zeolitic Materials

KAUST Repository

Kim, Wun-gwi

2012-11-27

The synthesis of hybrid zeolitic materials with complex micropore-mesopore structures and morphologies is an expanding area of recent interest for a number of applications. Here we report a new type of hybrid zeolite material, composed of a layered zeolite material grown epitaxially on the surface of a bulk zeolite material. Specifically, layered (2-D) MFI sheets were grown on the surface of bulk MFI crystals of different sizes (300 nm and 10 μm), thereby resulting in a hybrid material containing a unique morphology of interconnected micropores (∼0.55 nm) and mesopores (∼3 nm). The structure and morphology of this material, referred to as a "bulk MFI-layered MFI" (BMLM) material, was elucidated by a combination of XRD, TEM, HRTEM, SEM, TGA, and N2 physisorption techniques. It is conclusively shown that epitaxial growth of the 2-D layered MFI sheets occurs in at least two principal crystallographic directions of the bulk MFI crystal and possibly in the third direction as well. The BMLM material combines the properties of bulk MFI (micropore network and mechanical support) and 2-D layered MFI (large surface roughness, external surface area, and mesoporosity). As an example of the uses of the BMLM material, it was incorporated into a polyimide and fabricated into a composite membrane with enhanced permeability for CO2 and good CO2/CH4 selectivity for gas separations. SEM-EDX imaging and composition analysis showed that the polyimide and the BMLM interpenetrate into each other, thereby forming a well-adhered polymer/particle microstructure, in contrast with the defective interfacial microstructure obtained using bare MFI particles. Analysis of the gas permeation data with the modified Maxwell model also allows the estimation of the effective volume of the BMLM particles, as well as the CO2 and CH4 gas permeabilities of the interpenetrated layer at the BMLM/polyimide interface. © 2012 American Chemical Society.

Inhibiting prolyl isomerase activity by hybrid organic-inorganic molecules containing rhodium(II) fragments.

Science.gov (United States)

Coughlin, Jane M; Kundu, Rituparna; Cooper, Julian C; Ball, Zachary T

2014-11-15

A small molecule containing a rhodium(II) tetracarboxylate fragment is shown to be a potent inhibitor of the prolyl isomerase FKBP12. The use of small molecules conjugates of rhodium(II) is presented as a general strategy for developing new protein inhibitors based on distinct structural and sequence features of the enzyme active site. Copyright © 2014 Elsevier Ltd. All rights reserved.

Spin probes of chemistry in zeolites

International Nuclear Information System (INIS)

Werst, D.W.; Trifunac, A.D.

1997-09-01

Electron spin resonance (EPR) studies in zeolites are reviewed in which radiolysis was used to ionize the zeolite lattice, create reactive intermediates, spin label reaction products and to provide a window onto chemistry and transport of adsorbates and matrix control of chemistry. The review examines reactions of radical cations and the influence of the geometry constraints inside the zeolite, explores how zeolite model systems can be used to learn about energy and charge transfer in solids and illustrates the use of radiolysis and EPR for in situ spectroscopic studies of solid-acid catalysis. The various spin probes created inside the zeolite pores report on properties of the zeolites as well as shed light on radiolytic processes

Tandem rhodium catalysis: exploiting sulfoxides for asymmetric transition-metal catalysis.

Science.gov (United States)

Kou, K G M; Dong, V M

2015-06-07

Sulfoxides are uncommon substrates for transition-metal catalysis due to their propensity to inhibit catalyst turnover. In a collaborative effort with Ken Houk, we developed the first dynamic kinetic resolution (DKR) of allylic sulfoxides using asymmetric rhodium-catalyzed hydrogenation. A detailed mechanistic analysis of this transformation using both experimental and theoretical methods revealed rhodium to be a tandem catalyst that promoted both hydrogenation of the alkene and racemization of the allylic sulfoxide. Using a combination of deuterium labelling and DFT studies, a novel mode of allylic sulfoxide racemization via a Rh(III)-π-allyl intermediate was identified.

Characterization and antibacterial activity of silver exchanged regenerated NaY zeolite from surfactant-modified NaY zeolite.

Science.gov (United States)

Salim, Mashitah Mad; Malek, Nik Ahmad Nizam Nik

2016-02-01

The antibacterial activity of regenerated NaY zeolite (thermal treatment from cetyltrimethyl ammonium bromide (CTAB)-modified NaY zeolite and pretreatment with Na ions) loaded with silver ions were examined using the broth dilution minimum inhibitory concentration (MIC) method against Escherichia coli (E. coli ATCC 11229) and Staphylococcus aureus (S. aureus ATCC 6538). X-ray diffraction (XRD), attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), energy dispersive X-ray (EDX) and chemical elemental analyses were used to characterize the regenerated NaY and AgY zeolites. The XRD patterns indicated that the calcination and addition of silver ions on regenerated NaY zeolite did not affect the structure of the regenerated NaY zeolite as the characteristic peaks of the NaY zeolite were retained, and no new peaks were observed. The regenerated AgY zeolite showed good antibacterial activity against both bacteria strains in distilled water, and the antibacterial activity of the samples increased with increasing Ag loaded on the regenerated AgY zeolite; the regenerated AgY zeolite was more effective against E. coli than S. aureus. However, the antibacterial activity of the regenerated AgY was not effective in saline solution for both bacteria. The study showed that CTAB-modified NaY zeolite materials could be regenerated to NaY zeolite using thermal treatment (550°C, 5h) and this material has excellent performance as an antibacterial agent after silver ions loading. Copyright © 2015 Elsevier B.V. All rights reserved.

Synthesis, structure, DNA/protein binding, and cytotoxic activity of a rhodium(III) complex with 2,6-bis(2-benzimidazolyl)pyridine.

Science.gov (United States)

Esteghamat-Panah, Roya; Hadadzadeh, Hassan; Farrokhpour, Hossein; Simpson, Jim; Abdolmaleki, Amir; Abyar, Fatemeh

2017-02-15

A new mononuclear rhodium(III) complex, [Rh(bzimpy)Cl 3 ] (bzimpy = 2,6-bis(2-benzimidazolyl)pyridine), was synthesized and characterized by elemental analysis and spectroscopic methods. The molecular structure of the complex was confirmed by single-crystal X-ray crystallography. The interaction of the complex with fish sperm DNA (FS-DNA) was investigated by UV spectroscopy, emission titration, and viscosity measurement in order to evaluate the possible DNA-binding mode and to calculate the corresponding DNA-binding constant. The results reveal that the Rh(III) complex interacts with DNA through groove binding mode with a binding affinity on the order of 10 4 . In addition, the binding of the Rh(III) complex to bovine serum albumin (BSA) was monitored by UV-Vis and fluorescence emission spectroscopy at different temperatures. The mechanism of the complex interaction was found to be static quenching. The thermodynamic parameters (ΔH, ΔS, and ΔG) obtained from the fluorescence spectroscopy data show that van der Waals interactions and hydrogen bonds play a major role in the binding of the Rh(III) complex to BSA. For the comparison of the DNA- and BSA-binding affinities of the free bzimpy ligand with its Rh(III) complex, the absorbance titration and fluorescence quenching experiments of the free bzimpy ligand with DNA and BSA were carried out. Competitive experiments using eosin Y and ibuprofen as site markers indicated that the complex was mainly located in the hydrophobic cavity of site I of the protein. These experimental results were confirmed by the results of molecular docking. Finally, the in vitro cytotoxicity properties of the Rh(III) complex against the MCF-7, K562, and HT-29 cell lines were evaluated and compared with those of the free ligand (bzimpy). It was found that the complexation process improved the anticancer activity significantly. Copyright © 2016 Elsevier Masson SAS. All rights reserved.

Separation of cesium and strontium with zeolites

Energy Technology Data Exchange (ETDEWEB)

Kanno, T; Hashimoto, H [Tohoku Univ., Sendai (Japan). Research Inst. of Mineral Dressing and Metallurgy

1976-06-01

The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it.

Separation of cesium and strontium with zeolites

International Nuclear Information System (INIS)

Kanno, Takuji; Hashimoto, Hiroyuki

1976-01-01

The basic studies of separation of cesium and strontium were made with specimens of zeolite, which are synthetic zeolites A, X and Y; synthetic mordenite; natural mordenite; and clinoptilolite. Ammonium chloride was used as eluent, because it was considered to be a most appropriate eluent in alkaline chlorides. Cesium was easily eluted from the zeolites A and X by ammonium chloride solution, but it was difficult to elute from the synthetic mordenite, natural mordenite and clinoptilolite by ammonium chloride solution, but it was difficult to elute from the zeolites A and X. The zeolite Y is the only one zeolite among these zeolites from which both of cesium and strontium were easily eluted by ammonium chloride solution. Strontium could be separated from cesium with zeolites by formation of Sr-EDTA chelate at pH above 11. In this process, cesium was only exchanged in zeolite column, but strontium flow out from it. (auth.)

Synthesis and Characterization of Zeolite Na−Y and Its Conversion to the Solid Acid Zeolite H−Y

DEFF Research Database (Denmark)

Warner, Terence Edwin; Galsgaard Klokker, Mads; Nielsen, Ulla Gro

2017-01-01

Zeolite Y has an iconic crystal structure, but more importantly, the hydrogen modification zeolite H−Y is the classic example of a solid acid which is used extensively as a catalyst in the oil industry. This metastable compound cannot be synthesized directly, which creates an opportunity to discuss...... various preparative strategies with the students, such as the three-stage procedure described here. Stage I concerns the hydrothermal synthesis of zeolite Na−Y, followed by ion-exchange with an ammonium acetate solution to form zeolite NH4−Y, and the latter is subsequently converted to zeolite H......−Y by thermolysis. Stages II and III may instead be performed using commercially available zeolites, Na−Y and NH4−Y, respectively, which shifts the learning objectives to structural characterization of zeolites. The characterization of the product and intermediate materials gives the students a practical insight...

Removal of pyridine and quinoline by bio-zeolite composed of mixed degrading bacteria and modified zeolite

International Nuclear Information System (INIS)

Bai Yaohui; Sun Qinghua; Xing Rui; Wen Donghui; Tang Xiaoyan

2010-01-01

In the process of the biodegradation of pyridine and quinoline, ammonium is often generated because of the transformation of N from pyridine and quinoline. Zeolite has been proven to be an effective sorbent for the removal of the ammonium. The natural zeolite can be modified to be the macroporous carrier in the biological wastewater treatment process. In this study, a specific bio-zeolite composed of mixed bacteria (a pyridine-degrading bacterium and a quinoline-degrading bacterium) and modified zeolite was used for biodegradation and adsorption in two types of wastewater: sterile synthetic and coking wastewater. The experimental results indicated that pyridine and quinoline could be degraded simultaneously by the mixed bacteria. Furthermore, NH 4 + -N transformed from pyridine and quinoline could be removed by the modified zeolite. In addition, the bacterial community structures of the coking wastewater and the bio-zeolite were monitored by the amplicon length heterogeneity polymerase-chain reaction (LH-PCR) technique. Both LH-PCR results and scanning electron microscope (SEM) observations indicated that the microorganisms, including BW001 and BW003, could be easily attached on the surface of the modified zeolite and that the bio-zeolite could be used in the treatment of wastewater containing pyridine and/or quinoline.

Catalysis with hierarchical zeolites

DEFF Research Database (Denmark)

Holm, Martin Spangsberg; Taarning, Esben; Egeblad, Kresten

2011-01-01

Hierarchical (or mesoporous) zeolites have attracted significant attention during the first decade of the 21st century, and so far this interest continues to increase. There have already been several reviews giving detailed accounts of the developments emphasizing different aspects of this research...... topic. Until now, the main reason for developing hierarchical zeolites has been to achieve heterogeneous catalysts with improved performance but this particular facet has not yet been reviewed in detail. Thus, the present paper summaries and categorizes the catalytic studies utilizing hierarchical...... zeolites that have been reported hitherto. Prototypical examples from some of the different categories of catalytic reactions that have been studied using hierarchical zeolite catalysts are highlighted. This clearly illustrates the different ways that improved performance can be achieved with this family...

The role of zeolite in the Fischer–Tropsch synthesis over cobalt–zeolite catalysts

International Nuclear Information System (INIS)

Sineva, L V; Mordkovich, V Z; Asalieva, E Yu

2015-01-01

The review deals with the specifics of the Fischer–Tropsch synthesis for the one-stage syncrude production from CO and H 2 in the presence of cobalt–zeolite catalytic systems. Different types of bifunctional catalysts (hybrid, composite) combining a Fischer–Tropsch catalyst and zeolite are reviewed. Special attention focuses on the mechanisms of transformations of hydrocarbons produced in the Fischer–Tropsch process on zeolite acid sites under the synthesis conditions. The bibliography includes 142 references

Characterization of Zeolite in Zeolite-Geopolymer Hybrid Bulk Materials Derived from Kaolinitic Clays

Directory of Open Access Journals (Sweden)

Hayami Takeda

2013-05-01

Full Text Available Zeolite-geopolymer hybrid materials have been formed when kaolin was used as a starting material. Their characteristics are of interest because they can have a wide pore size distribution with micro- and meso-pores due to the zeolite and geopolymer, respectively. In this study, Zeolite-geopolymer hybrid bulk materials were fabricated using four kinds of kaolinitic clays (a halloysite and three kinds of kaolinite. The kaolinitic clays were first calcined at 700 °C for 3 h to transform into the amorphous aluminosilicate phases. Alkali-activation treatment of the metakaolin yielded bulk materials with different amounts and types of zeolite and different compressive strength. This study investigated the effects of the initial kaolinitic clays on the amount and types of zeolite in the resultant geopolymers as well as the strength of the bulk materials. The kaolinitic clays and their metakaolin were characterized by XRD analysis, chemical composition, crystallite size, 29Si and 27Al MAS NMR analysis, and specific surface area measurements. The correlation between the amount of zeolite formed and the compressive strength of the resultant hybrid bulk materials, previously reported by other researchers was not positively observed. In the studied systems, the effects of Si/Al and crystalline size were observed. When the atomic ratio of Si/Al in the starting kaolinitic clays increased, the compressive strength of the hybrid bulk materials increased. The crystallite size of the zeolite in the hybrid bulk materials increased with decreasing compressive strength of the hybrid bulk materials.

Detergent zeolite filtration plant

OpenAIRE

Stanković Mirjana S.; Pezo Lato L.

2003-01-01

The IGPC Engineering Department designed basic projects for detergent zeolite filtration plant, using technology developed in the IGPC laboratories. Several projects were completed: technological, machine, electrical, automation. On the basis of these projects, a production plant with a capacity of 75,000 t/y was manufactured, at "Zeolite Mira", Mira (VE), Italy, in 1997, for increasing detergent zeolite production, from 50,000 to 100,000 t/y. The main goal was to increase the detergent zeoli...

Supported Metal Zeolites as Environmental Catalysts for Reduction of NOx Molecules

International Nuclear Information System (INIS)

May Nwe Win; Tin Tin Aye; Kyaw Myo Naing; Nyunt Wynn; Maung Maung Htay

2005-09-01

The NOx contamination of air is a major pollutant due to its reaction with the volatile organic compounds, which give rise to ground level (tropospheric) ozone. It is a conventional fact that NOx are one of the major components of car exhaust. In view of that fact, to sustain the tropospheric ozone is to reduce the amount of NOx in the air. Therefore, this paper is concerned with the catalytic activity of Fe-loaded zeolite and Cu-loaded zeolite used to decompose NIOx by SCR (selective catalytic reduction) reaction with very high activity have been studied. Their preparations, characterization by XRD, FT-IR and SEM were also studied. Fe and Cu containig were prepared by soild state ion-exchange method under ambient presure and at the temperature of 600C for 4 hours. From this study, selective catalytic reduction rection was observed, showing about 87% conversion of the NOx molecule with the corresponding optimum amount of catalyst (1.0+-0.5)g working under the reactor space volume of 30cm3 at ambient temperature (30-32)C

A Rhodium(III)-Based Inhibitor of Lysine-Specific Histone Demethylase 1 as an Epigenetic Modulator in Prostate Cancer Cells.

Science.gov (United States)

Yang, Chao; Wang, Wanhe; Liang, Jia-Xin; Li, Guodong; Vellaisamy, Kasipandi; Wong, Chun-Yuen; Ma, Dik-Lung; Leung, Chung-Hang

2017-03-23

We report herein a novel rhodium(III) complex 1 as a new LSD1 targeting agent and epigenetic modulator. Complex 1 disrupted the interaction of LSD1-H3K4me2 in human prostate carcinoma cells and enhanced the amplification of p21, FOXA2, and BMP2 gene promoters. Complex 1 was selective for LSD1 over other histone demethylases, such as KDM2b, KDM7, and MAO activities, and also showed antiproliferative activity toward human cancer cells. To date, complex 1 is the first metal-based inhibitor of LSD1 activity.

Synthesis of Zeolite from Fly Ash and Removal of Heavy Metal Ions from Newly Synthesized Zeolite

OpenAIRE

Solanki, Parag; Gupta, Vikal; Kulshrestha, Ruchi

2010-01-01

Coal fly ash was used to synthesize X-type zeolite by alkali fusion followed by hydrothermal treatment. Characteristics of the various Fly ash samples were carried out. Coal proximate analysis was done. Batch experiment was carried out for the adsorption of some heavy metal ions on to synthesized Zeolite. The cost of synthesized zeolite was estimated to be almost one-fifth of that of commercial 13X zeolite available in the market.

Zeolites - a high resolution electron microscopy study

International Nuclear Information System (INIS)

Alfredsson, V.

1994-10-01

High resolution transmission electron microscopy (HRTEM) has been used to investigate a number of zeolites (EMT, FAU, LTL, MFI and MOR) and a member of the mesoporous M41S family. The electron optical artefact, manifested as a dark spot in the projected centre of the large zeolite channels, caused by insufficient transfer of certain reflections in the objective lens has been explained. The artefact severely hinders observation of materials confined in the zeolite channels and cavities. It is shown how to circumvent the artefact problem and how to image confined materials in spite of disturbance caused by the artefact. Image processing by means of a Wiener filter has been applied for removal of the artefact. The detailed surface structure of FAU has been investigated. Comparison of experimental micrographs with images simulated using different surface models indicates that the surface can be terminated in different ways depending on synthesis methods. The dealuminated form of FAU (USY) is covered by an amorphous region. Platinum incorporated in FAU has a preponderance to aggregate in the (111) twin planes, probably due to a local difference in cage structure with more spacious cages. It is shown that platinum is intra-zeolitic as opposed to being located on the external surface of the zeolite crystal. This could be deduced from tomography of ultra-thin sections among observations. HRTEM studies of the mesoporous MCM-41 show that the pores have a hexagonal shape and also supports the mechanistic model proposed which involves a cooperative formation of a mesophase including the silicate species as well as the surfactant. 66 refs, 24 figs

Effect of different glasses in glass bonded zeolite

International Nuclear Information System (INIS)

Lewis, M.A.; Ackerman, J.P.; Verma, S.

1995-01-01

A mineral waste form has been developed for chloride waste salt generated during the pyrochemical treatment of spent nuclear fuel. The waste form consists of salt-occluded zeolite powders bound within a glass matrix. The zeolite contains the salt and immobilizes the fission products. The zeolite powders are hot pressed to form a mechanically stable, durable glass bonded zeolite. Further development of glass bonded zeolite as a waste form requires an understanding of the interaction between the glass and the zeolite. Properties of the glass that enhance binding and durability of the glass bonded zeolite need to be identified. Three types of glass, boroaluminosilicate, soda-lime silicate, and high silica glasses, have a range of properties and are now being investigated. Each glass was hot pressed by itself and with an equal amount of zeolite. MCC-1 leach tests were run on both. Soda-lime silicate and high silica glasses did not give a durable glass bonded zeolite. Boroaluminosilicate glasses rich in alkaline earths did bind the zeolite and gave a durable glass bonded zeolite. Scanning electron micrographs suggest that the boroaluminosilicate glasses wetted the zeolite powders better than the other glasses. Development of the glass bonded zeolite as a waste form for chloride waste salt is continuing

Platinum Group Thiophenoxyimine Complexes: Syntheses,Crystallographic and Computational Studies of Structural Properties

Energy Technology Data Exchange (ETDEWEB)

Krinsky, Jamin L.; Arnold, John; Bergman, Robert G.

2006-10-03

Monomeric thiosalicylaldiminate complexes of rhodium(I) and iridium(I) were prepared by ligand transfer from the homoleptic zinc(II) species. In the presence of strongly donating ligands, the iridium complexes undergo insertion of the metal into the imine carbon-hydrogen bond. Thiophenoxyketimines were prepared by non-templated reaction of o-mercaptoacetophenone with anilines, and were complexed with rhodium(I), iridium(I), nickel(II) and platinum(II). X-ray crystallographic studies showed that while the thiosalicylaldiminate complexes display planar ligand conformations, those of the thiophenoxyketiminates are strongly distorted. Results of a computational study were consistent with a steric-strain interpretation of the difference in preferred ligand geometries.

The extraction of rhodium from aqueous nitric acid by dinonylnaphthalene sulphonic acid

International Nuclear Information System (INIS)

Patel, N.M.; Miles, J.H.; Thornback, J.R.

1987-01-01

The extraction of rhodium from aqueous nitric acid using dinonylnaphthalene sulphonic acid has been investigated. The extraction occurs readily from 0.1 M to 1.0 M nitric acid and, since the rhodium is extracted as {Rh(H 2 O) 6 } 3+ into the inverted micelles of the organic solution, equilibration times are less than 5 minutes. Extraction is enhanced by addition of nitrite ion to form {Rh(H 2 O) 5 NO 2 } 2+ as the extracted species. (author)

Carbon monoxide adsorption on low-silica zeolites: from single to dual and to multiple cation sites.

Science.gov (United States)

Otero Areán, C; Rodríguez Delgado, M; López Bauçà, C; Vrbka, L; Nachtigall, P

2007-09-07

Infrared spectra of CO adsorbed on the Al-rich Na-A zeolite were analysed by using a combined theoretical and experimental approach, showing that such spectra cannot be interpreted by assigning each IR band to CO interacting with a specific type of single cation site. This concept, which usually works well for high-silica zeolites, should not be uncritically extended to Al-rich zeolites that are crowded with cations in configurations which lead to preferential formation of CO adsorption complexes involving more than one cation site.

Two-Dimensional Zeolites: Current Status and Perspectives

Czech Academy of Sciences Publication Activity Database

Roth, Wieslaw Jerzy; Nachtigall, P.; Morris, R. E.; Čejka, Jiří

2014-01-01

Roč. 114, č. 9 (2014), s. 4807-4837 ISSN 0009-2665 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : zeolites * mesoporous molecular sieves * Fischer-Tropsch synthesis Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 46.568, year: 2014

Zeolite Encapsulated Nanocrystalline CuO: A Redox Catalyst for the Oxidation of Secondary Alcohols

Directory of Open Access Journals (Sweden)

Sakthivel Vijaikumar

2008-01-01

Full Text Available Zeolite encapsulated nanocrystalline CuO is synthesized and characterized by powder XRD and HRTEM analyses which clearly show that the particles are less than 15 nm and the nanoparticles are highly dispersed. This nano CuO encapsulated CuY zeolite is used as catalyst in the oxidation of aromatic secondary alcohols. CuY zeolite acts as an efficient support for nano CuO, by stabilizing it and preventing its aggregation. Plausible mechanisms for the formation of the various products are also given.

Kinetic Adsorption Study of Silver Nanoparticles on Natural Zeolite: Experimental and Theoretical Models

Directory of Open Access Journals (Sweden)

Alvaro Ruíz-Baltazar

2015-12-01

Full Text Available In this research, the adsorption capacity of Ag nanoparticles on natural zeolite from Oaxaca is presented. In order to describe the adsorption mechanism of silver nanoparticles on zeolite, experimental adsorption models for Ag ions and Ag nanoparticles were carried out. These experimental data obtained by the atomic absorption spectrophotometry technique were compared with theoretical models such as Lagergren first-order, pseudo-second-order, Elovich, and intraparticle diffusion. Correlation factors R2 of the order of 0.99 were observed. Analysis by transmission electron microscopy describes the distribution of the silver nanoparticles on the zeolite outer surface. Additionally, a chemical characterization of the material was carried out through a dilution process with lithium metaborate. An average value of 9.3 in the Si/Al ratio was observed. Factors such as the adsorption behavior of the silver ions and the Si/Al ratio of the zeolite are very important to support the theoretical models and establish the adsorption mechanism of Ag nanoparticles on natural zeolite.

Zeolite ZSM-57

International Nuclear Information System (INIS)

Valyocsik, E.W.; Page, N.M.; Chu, C.T.W.

1989-01-01

This patent describes a synthetic porous crystalline zeolite having a molar ratio of XO 2 ; Y 2 O 3 of at least 4. Wherein X represents silicon and/or germanium and Y represents aluminum, boron, chromium, iron and/or gallium. The porous crystalline zeolite having at least the X-ray diffraction lines as set forth in the text

Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: the influence of zeolite chemical surface characteristics.

Science.gov (United States)

Alejandro, Serguei; Valdés, Héctor; Manéro, Marie-Hélène; Zaror, Claudio A

2014-06-15

In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity. Copyright © 2014 Elsevier B.V. All rights reserved.

Synthesis of LTA zeolite on corundum supports: Preliminary assessment for heavy metal removal from waste water

International Nuclear Information System (INIS)

Jacas, A.; Ortega, P.; Velasco, M. J.; Camblor, M. A.; Rodriguez, M. A.

2012-01-01

The effectiveness of materials based on LTA Zeolite as active phase, for their incorporation into systems aimed at the removal of heavy metals on waste water is evaluated in a preliminary way. This type of Zeolite with the main channel of a minimum free diameter of 0,41 nm and a low SiO 2 /Al 2 O 3 ratio is an interesting molecular sieve, which in turn display a high ion exchange capacity. From this point of view, LTA Zeolite crystals were obtained in situ by hydrothermal synthesis and characterized by x ray diffraction (XRD) and scanning electron microscopy (SEM). We have studied the effect of hydrothermal synthesis time at 378 K. Likewise, the removal capacity of heavy metal from the active phase was evaluated in as a first step on diluted solutions of cooper salts at slightly acidic pH (∼ 4,7). (Author) 28 refs.

Co-deposition of rhodium and tungsten films for the first-mirror on ITER

International Nuclear Information System (INIS)

Marot, Laurent; Steiner, Roland; Gantenbein, Markus; Mathys, Daniel; Meyer, Ernst

2011-01-01

The detailed characterizations of rhodium/tungsten films prepared by co-deposition using a dual magnetron sputtering have been carried out on silicon substrates at room temperature. Effects of the tungsten incorporated in the film on the chemical bonding state, optical reflectivity and crystallinity were investigated using X-ray photoelectron spectroscopy (XPS), reflectivity measurements, X-rays diffraction (XRD) and scanning electron microscopy (SEM). The incorporation of tungsten changes the films crystalline structure i.e. leading to Rh 3 W formation. The reflectivity of the films decreases linearly with the decrease of rhodium concentration. XPS and ultraviolet photoemission spectroscopy (UPS) measurements show a positive shift of the core level binding energy of rhodium which is coupled to a shift of the Rh d-band ΔE d away from the Fermi level. Opposite shifts are observed for tungsten.

Structural properties of small rhodium clusters

Energy Technology Data Exchange (ETDEWEB)

Soon, Yee Yeen; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technology, Multimedia University, Melaka Campus, 75450 Melaka (Malaysia)

2015-04-24

We report a systematic study of the structural properties of rhodium clusters at the atomistic level. A novel global-minimum search algorithm, known as parallel tempering multicanonical basin hopping plus genetic algorithm (PTMBHGA), is used to obtain the geometrical structures with lowest minima at the semi-empirical level where Gupta potential is used to describe the atomic interaction among the rhodium atoms. These structures are then re-optimized at the density functional theory (DFT) level with exchange-correlation energy approximated by Perdew-Burke-Ernzerhof (PBE) generalized gradient approximation (GGA). The structures are optimized for different spin multiplicities. The ones with lowest energies will be taken as ground-state structures. In most cases, we observe only minor changes in the geometry and bond length of the clusters as a result of DFT-level re-optimization. Only in some limited cases, the initial geometries obtained from the PTMBHGA are modified by the re-optimization. The variation of structural properties, such as ground-state geometry, symmetry and binding energy, with respect to the cluster size is studied and agreed well with other results available in the literature.

Incorporation of metals (Pt-Ni-Ru) in the zeolite ZSM-5 through ion exchange competitive: synthesis and characterization

International Nuclear Information System (INIS)

Barbosa, A.S.; Rodrigues, M.G.F.

2012-01-01

Zeolites are very important materials due to their high specific surface area. Moreover, they are suitable for use as catalyst support. Noble metals supported on zeolites have been widely used as catalysts in the petrochemical industry. This paper was prepared and characterized, a powder aiming its use in heterogeneous catalysis. Support was used as ZSM-5 and the method of incorporation of the metals (Ru-PtNi) was competitive ion exchange. The materials (ZSM-5 and Pt-Ni-Ru/ZSM-5) were characterized by spectrophotometry Energy Dispersive X-ray (EDX), X-Ray Diffraction (XRD) and nitrogen physisorption (BET method). Based on the results of X-ray diffraction, it is possible to demonstrate the preservation of the structure of zeolite ZSM-5 after the competitive ion Exchange with metals (Ru-Pt-Ni) and calcination. The dispersion of metals on ZSM-5 did not change the textural characteristics of the zeolite. (author)

Light-induced reduction of rhodium(III) and palladium(II) on titanium dioxide dispersions and the selective photochemical separation and recovery of gold(III), platinum(IV), and rhodium(III) in chloride media

Energy Technology Data Exchange (ETDEWEB)

Borgarello, E.; Serpone, N.; Emo, G.; Harris, R.; Pelizzetti, E.; Minero, C.

1986-12-03

Irradiation of aqueous TiO/sub 2/ dispersions containing palladium(II) or rhodium(III) chloride salts with AM1 simulated sunlight leads to the photoreduction of these metals, which are deposited on the semiconductor particle surface. Oxygen is detrimental to the photoreduction of rhodium(III) but not the photoreduction of palladium(II). However, in both cases the reduction process is most efficient if the solution contains CH/sub 3/OH, which acts to scavenge valence band holes of the illuminated TiO/sub 2/ semiconductor. The selective photoreduction and recovery of precious metals from a dilute solution (as might be found in industrial wastes) have been investigated for a mixture of gold(III), platinum(IV), and rhodium(III) chloride salts as a function of various parameters (pH, presence or absence of O/sub 2/, presence or absence of a hole scavenger, and the concentration of the semiconductor). At pH 0, gold is easily separated from platinum and rhodium. The rate of photoreduction of gold(III) on TiO/sub 2/ is nearly independent of the concentration of the semiconductor, under the experimental conditions employed; the limiting rate is 2.7 x 10/sup -7/ M s/sup -1/. The potential utility of this selective photochemical technique is discussed.

Biodiesel synthesis via transesterification of lipid Chlorophyta cultivated in walne rich carbon medium using KOH/Zeolite catalyst

Science.gov (United States)

Dianursanti, Hayati, Siti Zahrotul; Putri, Dwini Normayulisa

2017-11-01

Microalgae from the Chlorophyta division such as Nannochloropsis oculata and Chlorella vulgaris are highly potential to be developed as biodiesel feedstocks because they have a high oil content up to 58%. Biodiesel is produced by transesterification of triglycerides and alcohols with the aid of homogeneous catalysts such as KOH. However, the use of KOH catalysts produces soaps in the biodiesel synthesis. Heterogeneous catalysts are known to solve this problem. One of them is natural zeolite. Zeolite can be used as a catalyst and as a support catalyst. Loading KOH on the zeolite surface is expected to increase alkalinity in KOH/Zeolite catalysts so as to increase the activity of KOH/Zeolite catalyst in transesterification of triglyceride with methanol. In this experimental lipid of microalgae will be used for produced biodiesel via transesterification reaction with methanol and KOH/Zeolite as a catalyst heterogeneous at 60 °C for 3h and utilized catalyst modificated KOH/Zeolite with variation 0.5 M, 1 M and 1.5 M KOH. The modified zeolite was then analyzed by XRF, XRD and BET. The result showed that the yield of biodiesel from lipid N.oculata was 81,09% by 0.5KOH/Zeolite catalyst, 86,53% by 1KOH/Zeolite catalyst, 1,5KOH/Zeolite and 88,13% by 1.5KOH/Zeolit, while the biodiesel produced from lipid C.vulgaris was 59.29% by 0.5KOH/Zeolite, 82.27% by 1KOH/Zeolite and 83.72% by 1.5KOH/Zeolite.

A bioscaffolding strategy for hierarchical zeolites with a nanotube-trimodal network.

Science.gov (United States)

Li, Guannan; Huang, Haibo; Yu, Bowen; Wang, Yun; Tao, Jiawei; Wei, Yingxu; Li, Shougui; Liu, Zhongmin; Xu, Yan; Xu, Ruren

2016-02-01

Hierarchical zeolite monoliths with multimodal porosity are of paramount importance as they open up new horizons for advanced applications. So far, hierarchical zeolites based on nanotube scaffolds have never been reported. Inspired by the organization of biominerals, we have developed a novel precursor scaffolding-solid phase crystallization strategy for hierarchical zeolites with a unique nanotube scaffolding architecture and nanotube-trimodal network, where biomolecular self-assembly (BSA) provides a scaffolding blueprint. By vapor-treating Sil-1 seeded precursor scaffolds, zeolite MFI nanotube scaffolds are self-generated, during which evolution phenomena such as segmented voids and solid bridges are observed, in agreement with the Kirkendall effect in a solid-phase crystallization system. The nanotube walls are made of intergrown single crystals rendering good mechanical stability. The inner diameter of the nanotube is tunable between 30 and 90 nm by varying the thickness of the precursor layers. Macropores enclosed by cross-linked nanotubes can be modulated by the choice of BSA. Narrow mesopores are formed by intergrown nanocrystals. Hierarchical ZSM-5 monoliths with nanotube (90 nm), micropore (0.55 nm), mesopore (2 nm) and macropore (700 nm) exhibit superior catalytic performance in the methanol-to-hydrocarbon (MTH) conversion compared to conventional ZSM-5. BSA remains intact after crystallization, allowing a higher level of organization and functionalization of the zeolite nanotube scaffolds. The current work may afford a versatile strategy for hierarchical zeolite monoliths with nanotube scaffolding architectures and a nanotube-multimodal network leading to self-supporting and active zeolite catalysts, and for applications beyond.

Ion-exchange properties of zeolite/glass hybrid materials

International Nuclear Information System (INIS)

Taira, Nobuyuki; Yoshida, Kohei; Fukushima, Takuya

2017-01-01

Hybrid materials were prepared from ground glass powder and various zeolites such as A-type, mordenite, X-type, and Y-type zeolites, and their ion removal effect was investigated. The hybrid materials of A-type, Y-type, and mordenite zeolites showed similar Sr"2"+ removal rates from aqueous solutions. The removal rate of Sr"2"+ ions increased as the amount of zeolite in the hybrid materials increased. Compared with other hybrid materials, the hybrid materials of X-type zeolite showed higher Sr"2"+ removal rates, especially for zeolite content greater than 25%. As the amount of X-type zeolite in the hybrid materials increased, the Sr"2"+ removal rate increased greatly, with a 100% removal rate when the content of X-type zeolite exceeded 62.5%. (author)

Introduction to zeolite theory and modelling

NARCIS (Netherlands)

Santen, van R.A.; Graaf, van de B.; Smit, B.; Bekkum, van H.

2001-01-01

A review. Some of the recent advances in zeolite theory and modeling are present. In particular the current status of computational chem. in Bronsted acid zeolite catalysis, mol. dynamics simulations of mols. adsorbed in zeolites, and novel Monte Carlo technique are discussed to simulate the

Rhodium SPND's Error Reduction using Extended Kalman Filter combined with Time Dependent Neutron Diffusion Equation

International Nuclear Information System (INIS)

Lee, Jeong Hun; Park, Tong Kyu; Jeon, Seong Su

2014-01-01

The Rhodium SPND is accurate in steady-state conditions but responds slowly to changes in neutron flux. The slow response time of Rhodium SPND precludes its direct use for control and protection purposes specially when nuclear power plant is used for load following. To shorten the response time of Rhodium SPND, there were some acceleration methods but they could not reflect neutron flux distribution in reactor core. On the other hands, some methods for core power distribution monitoring could not consider the slow response time of Rhodium SPND and noise effect. In this paper, time dependent neutron diffusion equation is directly used to estimate reactor power distribution and extended Kalman filter method is used to correct neutron flux with Rhodium SPND's and to shorten the response time of them. Extended Kalman filter is effective tool to reduce measurement error of Rhodium SPND's and even simple FDM to solve time dependent neutron diffusion equation can be an effective measure. This method reduces random errors of detectors and can follow reactor power level without cross-section change. It means monitoring system may not calculate cross-section at every time steps and computing time will be shorten. To minimize delay of Rhodium SPND's conversion function h should be evaluated in next study. Neutron and Rh-103 reaction has several decay chains and half-lives over 40 seconds causing delay of detection. Time dependent neutron diffusion equation will be combined with decay chains. Power level and distribution change corresponding movement of control rod will be tested with more complicated reference code as well as xenon effect. With these efforts, final result is expected to be used as a powerful monitoring tool of nuclear reactor core

Rhodium SPND's Error Reduction using Extended Kalman Filter combined with Time Dependent Neutron Diffusion Equation

Energy Technology Data Exchange (ETDEWEB)

Lee, Jeong Hun; Park, Tong Kyu; Jeon, Seong Su [FNC Technology Co., Ltd., Yongin (Korea, Republic of)

2014-05-15

The Rhodium SPND is accurate in steady-state conditions but responds slowly to changes in neutron flux. The slow response time of Rhodium SPND precludes its direct use for control and protection purposes specially when nuclear power plant is used for load following. To shorten the response time of Rhodium SPND, there were some acceleration methods but they could not reflect neutron flux distribution in reactor core. On the other hands, some methods for core power distribution monitoring could not consider the slow response time of Rhodium SPND and noise effect. In this paper, time dependent neutron diffusion equation is directly used to estimate reactor power distribution and extended Kalman filter method is used to correct neutron flux with Rhodium SPND's and to shorten the response time of them. Extended Kalman filter is effective tool to reduce measurement error of Rhodium SPND's and even simple FDM to solve time dependent neutron diffusion equation can be an effective measure. This method reduces random errors of detectors and can follow reactor power level without cross-section change. It means monitoring system may not calculate cross-section at every time steps and computing time will be shorten. To minimize delay of Rhodium SPND's conversion function h should be evaluated in next study. Neutron and Rh-103 reaction has several decay chains and half-lives over 40 seconds causing delay of detection. Time dependent neutron diffusion equation will be combined with decay chains. Power level and distribution change corresponding movement of control rod will be tested with more complicated reference code as well as xenon effect. With these efforts, final result is expected to be used as a powerful monitoring tool of nuclear reactor core.

Isobutane/2-butene alkylation with zeolite Y without BrÆnsted acidity

OpenAIRE

Rosenbach Jr, Nilton; Mota, Claudio J. A.

2005-01-01

Alkylation of isobutane with 2-butene was performed on metal-exchanged Y zeolites, using an alkylchloride as carbocation initiator. The results indicated that, compared with a protonic zeolite, the deactivation was significantly slower and the production of trimethylpentanes was higher on the metal-exchanged zeolites. The metal cations act as Lewis acids, interacting with the chloride initiating the carbocationic reactions. The results also support the view that protonic sites on the catalyst...

Producing zeolites from fly ash

International Nuclear Information System (INIS)

Rayalu, S.; Labhestwar, N.K.; Biniwale, R.B.; Udhoji, J.S.; Meshram, S.U.; Khanna, P.

1998-01-01

Fly ash has virtually become a menace of thermal power generation, leading to its devastating effects on the environment. Development of alternate methods of its disposal - especially those with recourse to recovery of valuable materials-has thus become imperative. This paper deals with the utilisation of fly ash for the production of high value-added products, viz., commercial grade zeolites. The physico-chemical and morphological characteristics of fly ash based Zeolite-A (FAZ-A) compares well with commercial Zeolite-A. High calcium binding capacity, appropriate particle/pore size and other detergency characteristics of FAZ-A brings forth its potential as a substitute for phosphatic detergent builder. The technology is extremely versatile, and other products like Zeolite-X, Zeolite-Y, sodalite and mordenite are also amenable for cost effective production with modifications in certain reaction parameters. Low temperature operations, ready availability of major raw materials, simplicity of process and recycling of unused reactants and process water are special features of the process. (author)

Human bile sorption by cancrinite-type zeolites

International Nuclear Information System (INIS)

Linares, Carlos F.; Colmenares, Maryi; Ocanto, Freddy; Valbuena, Oscar

2009-01-01

A nitrated cancrinite-type zeolite was synthesized from zeolite X, NaOH and NaNO 3 solutions under autogeneous pressure at 80 deg. C for 48 h. This zeolite was characterized by X-ray diffraction (XRD), FT-IR-spectroscopy, scanning electron microscopy (SEM) and BET surface area. XRD, SEM and FT-IR confirmed the presence of nitrated cancrinite-type zeolite without other collateral phases as sodalite. Then, this sodium zeolite was exchanged with potassium and calcium cations and finally, these modified zeolites were reacted with biliar solutions from human gallbladder. Several factors such as: mass of used cancrinite, nature of the exchanged cation and reaction time of the cancrinite-bile solution interactions were studied. The composition of bile solutions (bile acids, phospholipids and bilirubin) was analyzed before and after the cancrinite-bile solution reaction. Results showed that the components of the bile were notably reduced after the contact with solids. Ca-cancrinite, 120 min of reaction time and 500 mg of solids were the best conditions determined for the bile acid reduction in human bile. When the modified zeolites were compared with the commercial cholestyramine, it was found that zeolites were more active than the latter. These zeolites may be an alternative choice to diminish cholesterol levels in hypercholesterolemic patients

Properties of glass-bonded zeolite monoliths

International Nuclear Information System (INIS)

Lewis, M.A.; Fischer, D.F.; Murphy, C.D.

1994-01-01

It has been shown that mineral waste forms can be used to immobilize waste salt generated during the pyrochemical processing of spent fuel from the Integral Fast Reactor (IFR). Solid, leach resistant monoliths were formed by hot-pressing mixtures of salt-occluded zeolite A powders and glass frit at 990 K and 28 MPa. Additional samples have now been fabricated and tested. Normalized release rates for all elements, including iodide and chloride, were less than 1 g/m 2 d in 28-day tests in deionized water and in brine at 363 K (90 degrees C). Preliminary results indicate that these rates fall with time with both leachants and that the zeolite phase in the glass-bonded zeolite does not function as an ion exchanger. Some material properties were measured. The Poisson ratio and Young's modulus were slightly smaller in glass-bonded zeolite than in borosilicate glass. Density depended on zeolite fraction. The glass-bonded zeolite represents a promising mineral waste form for IFR salt

Enantioselective Access to Spirocyclic Sultams by Chiral Cp(x) -Rhodium(III)-Catalyzed Annulations.

Science.gov (United States)

Pham, Manh V; Cramer, Nicolai

2016-02-12

Chiral spirocyclic sultams are a valuable compound class in organic and medicinal chemistry. A rapid entry to this structural motif involves a [3+2] annulation of an N-sulfonyl ketimine and an alkyne. Although the directing-group properties of the imino group for C-H activation have been exploited, the developments of related asymmetric variants have remained very challenging. The use of rhodium(III) complexes equipped with a suitable atropchiral cyclopentadienyl ligand, in conjunction with a carboxylic acid additive, enables an enantioselective and high yielding access to such spirocyclic sultams. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Ionic liquid ultrasound assisted dispersive liquid-liquid microextraction method for preconcentration of trace amounts of rhodium prior to flame atomic absorption spectrometry determination

Energy Technology Data Exchange (ETDEWEB)

Molaakbari, Elaheh [Chemistry Department, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Young Research Society, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Mostafavi, Ali, E-mail: mostafavi.ali@gmail.com [Chemistry Department, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of); Afzali, Daryoush [Environment and Nanochemistry Department, Research Institute of Environmental Science, International Center for Science, High Technology and Environmental Science, Kerman (Iran, Islamic Republic of); Mineral Industries Research Center, Shahid Bahonar University of Kerman, Kerman (Iran, Islamic Republic of)

2011-01-30

In this article, we consider ionic liquid based ultrasound-assisted dispersive liquid-liquid microextraction of trace amounts of rhodium from aqueous samples and show that this is a fast and reliable sample pre-treatment for the determination of rhodium ions by flame atomic absorption spectrometry. The Rh(III) was transferred into its complex with 2-(5-bromo-2-pyridylazo)-5-diethylamino phenol as a chelating agent, and an ultrasonic bath with the ionic liquid, 1-octyl-3-methylimidazolium bis (trifluoromethylsulfonyl) imide at room temperature was used to extract the analyte. The centrifuged rhodium complex was then enriched in the form of ionic liquid droplets and prior to its analysis by flame atomic absorption spectrometry, 300 {mu}L ethanol was added to the ionic liquid-rich phase. Finally, the influence of various parameters on the recovery of Rh(III) was optimized. Under optimum conditions, the calibration graph was linear in the range of 4.0-500.0 ng mL{sup -1}, the detection limit was 0.37 ng mL{sup -1} (3S{sub b}/m, n = 7) and the relative standard deviation was {+-}1.63% (n = 7, C = 200 ng mL{sup -1}). The results show that ionic liquid based ultrasound assisted dispersive liquid-liquid microextraction, combined with flame atomic absorption spectrometry, is a rapid, simple, sensitive and efficient analytical method for the separation and determination of trace amounts of Rh(III) ions with minimum organic solvent consumption.

Vibrational properties of water molecules adsorbed in different zeolitic frameworks

International Nuclear Information System (INIS)

Crupi, V; Longo, F; Majolino, D; Venuti, V

2006-01-01

The perturbation of water 'sorbed' in samples of zeolites of different structural type, genesis, and cation composition (K-, Na-, Mg- and Ca-rich zeolites), namely the CHA framework of a synthetic K-chabazite, the LTA framework of synthetic Na-A and Mg50-A zeolites, and the NAT framework of a natural scolecite, has been studied by FTIR-ATR spectroscopy, in the -10 to +80 o C temperature range. The aim was to show how differences in the chemical composition and/or in the topology of the zeolite framework and, in particular, the possibility for the guest water molecules to develop guest-guest and/or host-guest interactions, lead to substantial differences in their vibrational dynamical properties. The spectra, collected in the O-H stretching and H 2 O bending mode regions, are complex, with multiple bands being observed. As far as water in the CHA and LTA frameworks is concerned, whose behaviour is governed by the balance of water-water, water-framework and water-extra-framework cations interactions, the assignment of the resolved components of the O-H stretching band has been discussed by fitting the band shapes into individual components attributed to H 2 O molecules engaged in different degrees of hydrogen bonding. A detailed quantitative picture of the connectivity pattern of water, as a function of temperature and according to the chemical and topological properties of the environment, is furnished. The H 2 O bending vibrational bands give additional information that perfectly agrees with the results obtained from the analysis of the O-H stretching spectral region. In the case of scolecite, a small-pored zeolite where water-water interactions are eliminated, the increased complexity observed in the infrared spectra in the O-H stretching and H 2 O bending regions was explained as due to the hydrogen bonding between the water molecules and the network, and also with the extra-framework cation. Furthermore, these observations have been correlated with the different

Rhodium deposition onto a 4-mercaptopyridine SAM on Au(1 1 1)

Energy Technology Data Exchange (ETDEWEB)

Manolova, M. [Institute of Electrochemistry, University of Ulm, 89069 Ulm (Germany); Kayser, M. [Institute of Electrochemistry, University of Ulm, 89069 Ulm (Germany); Kolb, D.M. [Institute of Electrochemistry, University of Ulm, 89069 Ulm (Germany)]. E-mail: dieter.kolb@uni-ulm.de; Boyen, H.-G. [Institute of Solid State Physics, University of Ulm, 89069 Ulm (Germany); Ziemann, P. [Institute of Solid State Physics, University of Ulm, 89069 Ulm (Germany); Mayer, D. [BASF Electronic Materials GmbH, 67056 Ludwigshafen (Germany); Wirth, A. [BASF Electronic Materials GmbH, 67056 Ludwigshafen (Germany)

2007-02-10

The application of a recently developed method for the deposition of Pd and Pt on top of a SAM, has been successfully extended to Rh, thus proving the versatility of the new concept. Experimental evidence from cyclic voltammetry, in situ STM and ex situ X-ray photoemission spectroscopy is presented for the deposition of monoatomic high rhodium islands onto a 4-mercaptopyridine self-assembled monolayer on a Au(1 1 1) electrode. By repetitive complexation of the Rh ions to the ring-nitrogen and reduction in a Rh-ion free solution, an almost completely covered SAM is obtained. The consequences of making contacts for molecular electronics are briefly discussed.

Rhodium coated mirrors deposited by magnetron sputtering for fusion applications

International Nuclear Information System (INIS)

Marot, L.; De Temmerman, G.; Oelhafen, P.; Covarel, G.; Litnovsky, A.

2007-01-01

Metallic mirrors will be essential components of all optical spectroscopy and imaging systems for ITER plasma diagnostics. Any change in the mirror performance, in particular, its reflectivity, due to erosion of the surface by charge exchange neutrals or deposition of impurities will influence the quality and reliability of the detected signals. Due to its high reflectivity in the visible wavelength range and its low sputtering yield, rhodium appears as an attractive material for first mirrors in ITER. However, the very high price of the raw material calls for using it in the form of a film deposited onto metallic substrates. The development of a reliable technique for the preparation of high reflectivity rhodium films is therefore of the highest importance. Rhodium layers with thicknesses of up to 2 μm were produced on different substrates of interest (Mo, stainless steel, Cu) by magnetron sputtering. Produced films exhibit a low roughness and crystallite size of about 10 nm with a dense columnar structure. No impurities were detected on the surface after deposition. Scratch tests demonstrate that adhesion properties increase with substrate hardness. Detailed optical characterizations of Rh-coated mirrors as well as results of erosion tests performed both under laboratory conditions and in the TEXTOR tokamak are presented in this paper

Rhodium-coated mirrors deposited by magnetron sputtering for fusion applications

International Nuclear Information System (INIS)

Marot, L.; Temmermann, G. de; Oelhafen, P.; Mathys, D.; Covarel, G.; Litnovsky, A.

2007-01-01

Metallic mirrors will be essential components of all optical spectroscopy and imaging systems for plasma diagnostics that will be used in ITER. Any change in the mirror performance, in particular its reflectivity, will influence the quality and reliability of detected signals. Due to its high reflectivity in the visible wavelength range and its low sputtering yield, rhodium may be a good candidate material for first mirrors in ITER. However, the very high price of the raw material calls for using it in the form of a film deposited onto metallic substrates. The development of a reliable technique for the preparation of high reflectivity rhodium films is therefore of the highest importance. Rhodium layers with thicknesses of up to 2 μm were produced on different relevant substrates (Mo, Stainless Steel, Cu) by magnetron sputtering. Produced films exhibit a low roughness, crystallite size of about 10 nm with a dense columnar structure. No impurities were detected on the surface after deposition. Scratch test results demonstrate that adhesion properties increase with the substrate hardness. The detailed optical characterizations of Rh coated mirrors as well as the results of erosion tests performed both under laboratory conditions and in TEXTOR will be presented in this paper. (orig.)

Preparation and characterization of new zeolite membranes. Application to gaseous separation; Preparation et caracterisation de nouvelles membranes de zeolithe application a la separation gazeuse

Energy Technology Data Exchange (ETDEWEB)

Anstett, M.

1996-11-25

Zeolites are interesting for the preparation of inorganic membranes which could be used for the continuous separation of gas and liquids by gas permeation and pervaporation. Zeolites membranes are obtained by hydrothermal synthesis and are characterized by XRD, SEM, TDA, IR, chemical analysis, EPMA, NMR, MAS NMR and gas permeation. After some tests of preparation of zeolite CHA and MFI self supporting membranes, the work is turned towards the preparation of zeolite MFI membranes supported by porous disks or {alpha} alumina, glass and tubes of carbon covered with a thin layer or zirconium dioxide. It is shown that the characteristics of the support (reactivity, pores dimensions, ...) strongly influence the quality of the prepared membrane. Two originals preparation processes are finalized. For the alumina disks, a gel precursor of zeolite is firs formed at the surface of the support by immersing successively that support in two non miscible liquids before the crystallisation. The gel is then converted into the zeolite by contact with water vapor. The zeolite layer obtained is localized at the surface of the support and present not only at the outside but also at the inside of the support. The characteristics of the zeolite layer can be controlled and the method can be adapted to various porous supports. The membrane obtained is interesting for hydrocarbons separations, for example the separation of methane and isobutane. In the case of Vycor glass disks, the reactivity of the support is first enhanced by contact with saturated water vapour. The temperature of the synthesis is then chosen relatively low in order to limit the attack of the support. With that method, a basic solution can be used without degradation of the support.The basicity leads to the formation of little crystals whose assembling is compact and homogeneous. The membrane obtained is interesting for example for the separation of normal butane and isobutane. (author) 71 refs.

Fabrication of 6FDA-durene membrane incorporated with zeolite T and aminosilane grafted zeolite T for CO2/CH4 separation

Science.gov (United States)

Jusoh, Norwahyu; Fong Yeong, Yin; Keong Lau, Kok; Shariff, Azmi Mohd

2017-08-01

In the present work, zeolite T and aminosilane grafted zeolite T are embedded into 6FDA-durene polyimide phase for the fabrication of mixed matrix membranes (MMMs). FESEM images demonstrated that the improvement of interfacial adhesion between zeolite and polymer phases in MMM loaded with aminosilane grafted zeolite T was not significant as compared to zeolite T/6FDA-durene MMM. From the gas permeation test, CO2/CH4 selectivity up to 26.4 was achieved using MMM containing aminosilane grafted zeolite T, while MMM loaded with ungrafted zeolite T showed CO2/CH4 selectivity of 19.1. In addition, MMM incorporated with aminosilane grafted zeolite T particles successfully lies on Robeson upper bound 2008, which makes it an attractive candidate for CO2/CH4 separation.

In situ fast pyrolysis of biomass with zeolite catalysts for bioaromatics/gasoline production: A review

International Nuclear Information System (INIS)

Galadima, Ahmad; Muraza, Oki

2015-01-01

Highlights: • Biomass upgrading by fast pyrolysis is an attractive bioaromatics production. • Zeolite catalysts are key important systems considered for the process. • Catalytic activity depend on zeolite structure, acidity and textural features. • Recent literature on the role of the zeolite catalysts critically tailored. • Hierarchical zeolites are prospective catalysts for industrial applications. - Abstract: The fast pyrolysis of biomass-based feedstocks is currently gaining considerable attention as an industrial and sustainable option for the production of gasoline-range bioaromatics. The complex composition of biomass molecules and a series of reactions involved during the upgrading process require the incorporation of sufficiently acidic and topological catalysts. This paper carefully documents and analyzes recent publications that have investigated the properties of zeolites to enhance the yield of bioaromatics during in situ fast pyrolysis. Issues related to the effects of zeolite’s textural, topological and acidic properties are critically examined. Factors responsible for catalyst deactivation and the mechanistic roles of the catalysts used are discussed. This paper also explores the prospects of hierarchical zeolites and municipal solid waste (MSW) as catalysts and feedstocks for the fast pyrolysis process.

PHYSICAL, CHEMICAL, AND STRUCTURAL EVOLUTION OF ZEOLITE-CONTAINING WASTE FORMS PRODUCED FROM METAKAOLINITE AND CALCINED HLW

International Nuclear Information System (INIS)

Pareizs, J. M.; Jantzenm, C.M.

2000-01-01

Natural and synthetic zeolites are extremely versatile materials. They can adsorb a variety of liquids and gases, and also take part in cation exchange reactions. Zeolites have the ability to sequester ions in lattice positions or within their networks of channels and voids. The zeolites can host alkali, alkaline earth and a variety of higher valance cations. As such they may be a viable alternative for immobilization of low activity waste (LAW) salts and calcines. The process for synthesizing zeolites is well documented for pure starting materials. A reactive aluminosilicate is reacted with an alkaline hydroxide at low temperature (<300 C) to form a zeolite. Processing time and temperature and specific reactants determine the type of zeolite formed. Zeolites are easy to make, and can be synthesized from a wide variety of natural and man made materials. However, relatively little is known about the process if one of the starting materials is a poorly characterized complex mixture of oxides (waste) containing nearly every element in the periodic table. The purpose of this work is to develop a clearer understanding of the advantages and limitations of producing a zeolite waste form from radioactive waste. Dr. M. W. Grutzeck at the Pennsylvania State University is investigating the production of a zeolite waste form using nonradioactive simulants. Dr. C. M. Jantzen and J. M. Pareizs at the Savannah River Technology Center will use the results from simulant work as a starting point for producing a zeolite waste form from an actual Savannah River Site radioactive waste stream

Physical, chemical, and structural evolution of zeolite-containing waste forms produced from metakaolinite and calcined HLW

International Nuclear Information System (INIS)

Pareizs, J.M.

2000-01-01

Natural and synthetic zeolites are extremely versatile materials. They can adsorb a variety of liquids and gases, and also take part in cation exchange reactions. Zeolites have the ability to sequester ions in lattice positions or within their networks of channels and voids. The zeolites can host alkali, alkaline earth and a variety of higher valence cations. As such they may be a viable alternative for immobilization of low activity waste (LAW) salts and calcines. The process for synthesizing zeolites is well documented for pure starting materials. A reactive aluminosilicate is reacted with an alkaline hydroxide at low temperature to form a zeolite. Processing time and temperature and specific reactants determine the type of zeolite formed. Zeolites are easy to make, and can be synthesized from a wide variety of natural and man made materials. However, relatively little is known about the process if one of the starting materials is a poorly characterized complex mixture of oxides (waste) containing nearly every element in the periodic table. The purpose of this work is to develop a clearer understanding of the advantages and limitations of producing a zeolite waste form from radioactive waste. Dr. M. W. Grutzeck at the Pennsylvania State University is investigating the production of a zeolite waste form using non-radioactive simulants. Dr. C. M. Jantzen and J. M. Pareizs at the Savannah River Technology Center will use the results from simulant work as a starting point for producing a zeolite waste form from an actual Savannah River Site radioactive waste stream

Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: The influence of zeolite chemical surface characteristics

Energy Technology Data Exchange (ETDEWEB)

Alejandro, Serguei [Laboratorio de Tecnologías Limpias (F. Ingeniería), Universidad Católica de la Santísima Concepción, Alonso de Ribera 2850, Concepción (Chile); Núcleo de Energías Renovables (F. Ingeniería), Universidad Católica de Temuco, Rudecindo Ortega 02950, Temuco (Chile); Valdés, Héctor, E-mail: hvaldes@ucsc.cl [Laboratorio de Tecnologías Limpias (F. Ingeniería), Universidad Católica de la Santísima Concepción, Alonso de Ribera 2850, Concepción (Chile); Manéro, Marie-Hélène [Université de Toulouse (France); INPT, UPS (France); Laboratoire de Génie Chimique, 4, Allée Emile Monso, F–31030 Toulouse (France); CNRS (France); Laboratoire de Génie Chimique, F–31030 Toulouse (France); Zaror, Claudio A. [Departamento de Ingeniería Química (F. Ingeniería), Universidad de Concepción, Concepción, Correo 3, Casilla 160–C (Chile)

2014-06-01

Highlights: • Surface acidity of modified natural zeolite is related to its chemical reactivity. • Brønsted acid sites are associated to toluene adsorption. • Lewis acid sites could decompose ozone generating surface active oxygen species. • Infrared spectra evidence active atomic oxygen and oxidation by-product formation. • 2NH4Z1 sample shows the highest reactivity toward adsorbed toluene. - Abstract: In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823 K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623 K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity.

Oxidative regeneration of toluene-saturated natural zeolite by gaseous ozone: The influence of zeolite chemical surface characteristics

International Nuclear Information System (INIS)

Alejandro, Serguei; Valdés, Héctor; Manéro, Marie-Hélène; Zaror, Claudio A.

2014-01-01

Highlights: • Surface acidity of modified natural zeolite is related to its chemical reactivity. • Brønsted acid sites are associated to toluene adsorption. • Lewis acid sites could decompose ozone generating surface active oxygen species. • Infrared spectra evidence active atomic oxygen and oxidation by-product formation. • 2NH4Z1 sample shows the highest reactivity toward adsorbed toluene. - Abstract: In this study, the effect of zeolite chemical surface characteristics on the oxidative regeneration of toluene saturated-zeolite samples is investigated. A Chilean natural zeolite (53% clinoptilolite, 40% mordenite and 7% quartz) was chemically modified by acid treatment with hydrochloric acid and by ion-exchange with ammonium sulphate. Thermal pre-treatments at 623 and 823 K were applied and six zeolite samples with different chemical surface characteristics were generated. Chemical modification of natural zeolite followed by thermal out-gassing allows distinguishing the role of acidic surface sites on the regeneration of exhausted zeolites. An increase in Brønsted acid sites on zeolite surface is observed as a result of ammonium-exchange treatment followed by thermal treatment at 623 K, thus increasing the adsorption capacity toward toluene. High ozone consumption could be associated to a high content of Lewis acid sites, since these could decompose ozone into atomic active oxygen species. Then, surface oxidation reactions could take part among adsorbed toluene at Brønsted acid sites and surface atomic oxygen species, reducing the amount of adsorbed toluene after the regenerative oxidation with ozone. Experimental results show that the presence of adsorbed oxidation by-products has a negative impact on the recovery of zeolite adsorption capacity

Zeolites in poultry and swine production

Directory of Open Access Journals (Sweden)

Aline Félix Schneider

Full Text Available ABSTRACT: Zeolites are minerals that have intriguing properties such as water absorption, ion adsorption and cation exchange capacity. There are approximately 80 species of natural zeolites recognized and hundreds of artificial zeolites, which have been researched in several fields. Due to their chemical characteristics, zeolites have great potential for use in animal production, especially in poultry and swine farms, as food additives, litter amendment and treatment of residues, with direct and indirect effects on performance, yield and quality of carcass, ambience of farm sheds and reduction of environmental pollution.

Aldol condensation of furfural and acetone on zeolites

Czech Academy of Sciences Publication Activity Database

Kikhtyanin, O.; Kelbichová, V.; Vitvarová, Dana; Kubů, Martin; Kubička, D.

2014-01-01

Roč. 227, MAY 2014 (2014), s. 154-162 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : aldol condensation * oligomerization * zeolites Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 3.893, year: 2014

Regioselective nitration of aromatic substrates in zeolite cages

Indian Academy of Sciences (India)

Unknown

... mixture, responsible for the generation of large amounts of wastes, which ... benzene in gas phase over solid catalysts such as SiO2–Al2O3, supported ... selective nitration with a nitrogen dioxide-oxygen-zeolite H-β/HY as a solid inorganic.

Characterization of Mexican zeolite minerals

International Nuclear Information System (INIS)

Jimenez C, M.J.

2005-01-01

50% of the Mexican territory is formed by volcanic sequences of the Pliocene type, which appear extensively in the northwest states (Sonora, Sinaloa, Chihuahua, Durango) and west of Mexico (Jalisco and Nayarit), in central Mexico (Zacatecas, Guanajuato, San Luis Potosi, Queretaro, Hidalgo) and south of Mexico (Guerrero, Oaxaca); therefore, it is to be expected that in our country big locations of natural zeolites exist in its majority of the clinoptilolite type. The present study was focused toward the characterization of two Mexican natural zeolite rocks presumably of the clinoptilolite and filipsite types, one of them comes from the state of Chihuahua and the other of a trader company of non metallic minerals, due that these materials are not characterized, its are not known their properties completely and therefore, the uses that can be given to these materials. In this investigation work it was carried out the characterization of two Mexican zeolite rocks, one coming from the Arroyo zone, municipality of La Haciendita, in the state of Chihuahua; and the other one was bought to a trader company of non metallic minerals. The two zeolites so much in their natural form as conditioned with sodium; they were characterized by means of X-ray diffraction, scanning electron microscopy of high vacuum and elementary microanalysis (EDS), surface area analysis (BET), thermal gravimetric analysis. To differentiate the heulandite crystalline phase of the other clinoptilolite rock, its were carried out thermal treatments. The quantification of Al, Na, Ca, K, Mg, Fe was carried out in solution, by means of atomic absorption spectroscopy and the quantity of Si was determined by gravimetry. The zeolite rocks presented for the major part the crystalline heulandite and clinoptilolite phases for the most part, and it was found that the zeolite coming from the state of Chihuahua possesses a bigger content of heulandite and the denominated filipsite it is really a zeolite

Acidity in zeolite catalysis

NARCIS (Netherlands)

Santen, van R.A.; Gauw, de F.J.M.M.; Corma, A.; Melo, F.; Mendioroz, S.; Fierro, J.L.G.

2000-01-01

A review with 21 refs. is provided on our current understanding of the activation of hydrocarbons by protonic zeolites. One has to distinguish the proton affinity of a zeolite, measured in an equil. expt., from proton activation that dets. a kinetic catalytic result. The proton affinity depends on

Zeolite Nanoparticles for Selective Sorption of Plasma Proteins.

Science.gov (United States)

Rahimi, M; Ng, E-P; Bakhtiari, K; Vinciguerra, M; Ali Ahmad, H; Awala, H; Mintova, S; Daghighi, M; Bakhshandeh Rostami, F; de Vries, M; Motazacker, M M; Peppelenbosch, M P; Mahmoudi, M; Rezaee, F

2015-11-30

The affinity of zeolite nanoparticles (diameter of 8-12 nm) possessing high surface area and high pore volume towards human plasma proteins has been investigated. The protein composition (corona) of zeolite nanoparticles has been shown to be more dependent on the plasma protein concentrations and the type of zeolites than zeolite nanoparticles concentration. The number of proteins present in the corona of zeolite nanoparticles at 100% plasma (in vivo state) is less than with 10% plasma exposure. This could be due to a competition between the proteins to occupy the corona of the zeolite nanoparticles. Moreover, a high selective adsorption for apolipoprotein C-III (APOC-III) and fibrinogen on the zeolite nanoparticles at high plasma concentration (100%) was observed. While the zeolite nanoparticles exposed to low plasma concentration (10%) exhibited a high selective adsorption for immunoglobulin gamma (i.e. IGHG1, IGHG2 and IGHG4) proteins. The zeolite nanoparticles can potentially be used for selectively capture of APOC-III in order to reduce the activation of lipoprotein lipase inhibition during hypertriglyceridemia treatment. The zeolite nanoparticles can be adapted to hemophilic patients (hemophilia A (F-VIII deficient) and hemophilia B (F-IX deficient)) with a risk of bleeding, and thus might be potentially used in combination with the existing therapy.

Examination of zeolites by neutron reflection method

International Nuclear Information System (INIS)

Szegedi, S.; Varadi, M.; Boedy, Z.T.; Vas, L.

1991-01-01

Neutron reflection method has been used for the determination of zeolite content in minerals. The basis of this measurement is to observe the large difference between the water content of zeolite and that of other mineralic parts of the sample. The method suggested can be used in a zeolite mine for measuring the zeolite content continuously and controlling the quality of the end products. (author) 5 refs.; 3 figs.; 3 tabs

Colloidal processing and CO_2-capture performance Al_2O_3-zeolite 13X composites

International Nuclear Information System (INIS)

Andersson, L.; Akhtar, F.; Ojuva, A.; Bergstroem, L.

2012-01-01

Hierarchically porous composites for CO_2-capture have been produced by coating the inner walls of foam-like macroporous alumina monoliths, produced by templated synthesis, with microporous zeolite 13X particles. Homogeneous and dense coatings of the particulate adsorbent were obtained when the impregnation process was performed at a pH above 9. At this pH-level the colloidally stable suspensions of the negatively charged zeolite 13X particles could fill all the voids of the highly connected pore space of the alumina supports and attach to the monolith walls, which had been pre-coated with poly(ethylene imine). A CO_2-uptake as high as 5 mmol CO_2/g zeolite 13X was achieved for alumina-zeolite 13X composites through minimisation of the added inorganic binder, kaolin, to only 3.0 wt% with respect to zeolite content, and through optimisation of the thermal treatment.

Rhodium(iii)-catalyzed ortho-olefination of aryl phosphonates.

Science.gov (United States)

Chary, Bathoju Chandra; Kim, Sunggak

2013-09-25

Rhodium(iii)-catalyzed C-H olefination of aryl phosphonic esters is reported for the first time. In this mild and efficient process, the phosphonic ester group is utilized successfully as a new directing group. In addition, mono-olefination for aryl phosphonates is observed using a phosphonic diamide directing group.

The effect of pore size dimensions in isoreticular zeolites on carbon dioxide adsorption heats

Czech Academy of Sciences Publication Activity Database

Zukal, Arnošt; Shamzhy, Mariya; Kubů, Martin; Čejka, Jiří

2018-01-01

Roč. 24, MAR2018 (2018), s. 157-163 ISSN 2212-9820 R&D Projects: GA ČR GBP106/12/G015 EU Projects: European Commission(XE) 640979 - ShaleXenvironmenT Institutional support: RVO:61388955 Keywords : UTL zeolite * IPC-n zeolites * Carbon dioxide adsorption Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 4.292, year: 2016

Cross flow ultrafiltration of Cr (VI) using MCM-41, MCM-48 and Faujasite (FAU) zeolite-ceramic composite membranes.

Science.gov (United States)

Basumatary, Ashim Kumar; Kumar, R Vinoth; Ghoshal, Aloke Kumar; Pugazhenthi, G

2016-06-01

This work describes the removal of Cr (VI) from aqueous solution in cross flow mode using MCM-41, MCM-48 and FAU zeolite membranes prepared on circular shaped porous ceramic support. Ceramic support was manufactured using locally available clay materials via a facile uni-axial compaction method followed by sintering process. A hydrothermal technique was employed for the deposition of zeolites on the ceramic support. The porosity of ceramic support (47%) is reduced by the formation of MCM-41 (23%), MCM-48 (22%) and FAU (33%) zeolite layers. The pore size of the MCM-41, MCM-48 and FAU membrane is found to be 0.173, 0.142, and 0.153 μm, respectively, which is lower than that of the support (1.0 μm). Cross flow ultrafiltration experiments of Cr (VI) were conducted at five different applied pressures (69-345 kPa) and three cross flow rates (1.11 × 10(-7) - 2.22 × 10(-7) m(3)/s). The filtration studies inferred that the performance of the fabricated zeolite composite membranes is optimum at the maximum applied pressure (345 kPa) and the highest rejection is obtained with the lowest cross flow rate (1.11 × 10(-7) m(3)/s) for all three zeolite membrane. The permeate flux of MCM-41, MCM-48 and FAU zeolite composite membranes are almost remained constant in the entire duration of the separation process. The highest removal of 82% is shown by FAU membrane, while MCM-41 and MCM-48 display 75% and 77% of Cr (VI) removal, respectively for the initial feed concentration of 1000 ppm with natural pH of the solution at an applied pressure of 345 kPa. Copyright © 2016 Elsevier Ltd. All rights reserved.

Increased thermal conductivity monolithic zeolite structures

Science.gov (United States)

Klett, James; Klett, Lynn; Kaufman, Jonathan

2008-11-25

A monolith comprises a zeolite, a thermally conductive carbon, and a binder. The zeolite is included in the form of beads, pellets, powders and mixtures thereof. The thermally conductive carbon can be carbon nano-fibers, diamond or graphite which provide thermal conductivities in excess of about 100 W/mK to more than 1,000 W/mK. A method of preparing a zeolite monolith includes the steps of mixing a zeolite dispersion in an aqueous colloidal silica binder with a dispersion of carbon nano-fibers in water followed by dehydration and curing of the binder is given.

Effects of heating on salt-occluded zeolite

International Nuclear Information System (INIS)

Lewis, M.A.; Hash, M.C.; Pereira, C.; Ackerman, J.P.

1996-01-01

The electrometallurgical treatment of spent nuclear fuel generates a waste stream of fission products in the electrolyte, LiCl-KCl eutectic salt. Argonne National Laboratory is developing a mineral waste form for this waste stream. The waste form consists of a composite formed by hot pressing salt-occluded zeolite and a glass binder. Pressing conditions must be judiciously chosen. For a given pressure, increasing temperatures and hold times give denser products but the zeolite is frequently converted to sodalite. Reducing the temperature or hold time leads to a porous zeolite composite. Therefore, conditions that affect the thermal stability of salt-occluded zeolite both with and without glass are being investigated in an ongoing study. The parameters varied in this stage of the work were heating time, temperature, salt loading, and glass content. The heat-treated samples were examined primarily by X-ray diffraction. Large variations were found in the rate at which salt-occluded zeolite converted to other phases such as nepheline, salt, and sodalite. The products depended on the initial salt loading. Heating times required for these transitions depended on the procedure and temperature used to prepare the salt-occluded zeolite. Mixtures of glass and zeolite reacted much faster than the pure salt-occluded zeolite and were almost always converted to sodalite

Removal of U(VI) from aqueous solution using TiO{sub 2} modified β-zeolite

Energy Technology Data Exchange (ETDEWEB)

Liu, Peng; Yuan, Ni; Xiong, Wei; Wu, Hanyu; Pan, Duoqiang; Wu, Wangsuo [Lanzhou Univ. (China). Radiochemistry and Nuclear Environment Laboratory; Ministry of Education, Lanzhou (China). Key Laboratory of Special Function Materials and Structure Design

2017-07-01

β-Zeolite was synthesized and modified with TiO{sub 2}. The synthesized materials were characterized and used for removal of U(VI) from aqueous solutions. The influences of pH, contact time and temperature on U(VI) adsorption onto modified β-zeolite by TiO{sub 2} were studied by batch technique, and XPS was employed to analysed the experimental data. The dynamic process showed that the adsorption of U(VI) onto TiO{sub 2}/β-zeolite matched the pseudo-second-order kinetics model, and the adsorption of U(VI) were significantly dependent on pH values. Through simulating the adsorption isotherms by Langmuir, Freundlich and Dubini-Radushkevich (D-R) models, it could be seen, respectively that the adsorption patterns of U(VI) onto TiO{sub 2}/β-zeolite were mainly controlled by surface complexation, and the adsorption processes were endothermic and spontaneous. The modification of β-zeolite by TiO{sub 2} it shows a novel material for the removing of U(VI) from water environment for industrialized application.

Exfoliation of two-dimensional zeolites in liquid polybutadienes

KAUST Repository

Sabnis, Sanket

2017-06-16

Layered zeolite precursors were successfully exfoliated by brief shearing or sonication with the assistance of commercially available telechelic liquid polybutadienes at room temperature. The exfoliated zeolite nanosheets can form a stable suspension in an organic solvent, providing exciting potential for the fabrication of zeolite membranes, composite materials and hierarchical zeolites.

Sorption properties study of nitron fibre S-3 relative to rhodium (III)

International Nuclear Information System (INIS)

Rustamov, S.; Khusainov, A.D.; Shadieva, S.F.

2001-01-01

The purpose of present work is studying of sorption properties of nitron fibre S-3 relative to rhodium (III) from chloride solutions. Nitron sorbent S-3 was synthesised by reprocessing of wastes of production of nitron fibre by sulfited compound Na 2 Sn:NH 4 SCN=50:50 during 3 hours at temperature 90 d ig C . The sulfur containing in the sorbent was about 9%. During investigation by authors was determined that fibre nitron-S has good kinetic characteristics relative to rhodium (III), limitative stage of sorption process is diffusion and kinetics of sorption has mixed-diffusion character

Mechanistic insights into aqueous phase propanol dehydration in H-ZSM-5 zeolite

Energy Technology Data Exchange (ETDEWEB)

Mei, Donghai [Pacific Northwest National Laboratory, Physical and Computational Sciences Directorate & Institute for Integrated Catalysis, Richland WA 99352; Lercher, Johannes A. [Pacific Northwest National Laboratory, Physical and Computational Sciences Directorate & Institute for Integrated Catalysis, Richland WA 99352; Dept. of Chemistry and Catalysis Research Institute, TU München, Lichtenbergstrasse 4 Garching 85748 Germany

2016-10-06

Aqueous phase dehydration of 1-propanol over H-ZSM-5 zeolite was investigated using density functional theory (DFT) calculations. The water molecules in the zeolite pores prefer to aggregate via the hydrogen bonding network and be protonated at the Brønsted acidic sites (BAS). Two typical configurations, i.e., dispersed and clustered, of water molecules were identified by ab initio molecular dynamics simulation of the mimicking aqueous phase H-ZSM-5 zeolite unit cell with 20 water molecules per unit cell. DFT calculated Gibbs free energies suggest that the dimeric propanol-propanol, the propanol-water complex, and the trimeric propanol-propanol-water are formed at high propanol concentrations, which provide a kinetically feasible dehydration reaction channel of 1-propanol to propene. However, calculation results also indicate that the propanol dehydration via the unimolecular mechanism becomes kinetically discouraged due to the enhanced stability of the protonated dimeric propanol and the protonated water cluster acting as the BAS site for alcohol dehydration reaction. This work was supported by the US Department of Energy (DOE), Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences. Pacific Northwest National Laboratory (PNNL) is a multiprogram national laboratory operated for DOE by Battelle. Computing time was granted by the grand challenge of computational catalysis of the William R. Wiley Environmental Molecular Sciences Laboratory (EMSL). EMSL is a national scientific user facility located at Pacific Northwest National Laboratory (PNNL) and sponsored by DOE’s Office of Biological and Environmental Research.

Nuclear waste treatment using Iranian natural zeolites

International Nuclear Information System (INIS)

Kazemian, H.; Ghannadi Maraghe, M.

2001-01-01

Full text: The zeolite researches in Iran is a relatively new subject which has started about 10 years ago. The motivation for this scientific and interesting field was provided after discovery of significant deposits of natural zeolites in different regions of Iran as well as further developments of research institutions and the national concern to environmental protection especially the wastewater clean-up in point of view of recycling of such waste water to compensate some needs to water in other utilizations. This paper intends to review and describes scientific researches which have done on using zeolites in the field of nuclear waste treatment in Iran to introduce the potential resources to the world in more details. Zeolite tuffs are widely distributed in huge deposits in different regions of Iran. So far, the clinoptilolite tuffs are the most abundant natural zeolite which exist with zeolite content of 65%- 95%. Nowadays several different types of Iranian natural zeolites are characterized in point of view of chemical composition, type of structure, chemical, thermal, and radiation resistance using different instrumental and classical methods such as; X-ray diffraction (XRD), X-ray fluoresce (XRF), thermal methods of analysis (TA), scanning electron microscopy (SEM), analytical chemistry and radioanalytical methods as well as different ion-exchange techniques (e.g.3-7). The ability of Iranian natural clinoptilolite for removal of some fission products from nuclear wastewaters have been investigated. The selectivity of all investigated zeolites toward radiocesium and radiostrontium have been promising (e.g. 8-10). The successful synthesize of P zeolite from Iranian clinoptilolite-reach tuffs under different conditions were performed. The compatibility of zeolites with glass and cement matrices, for final disposal of radwaste, as well as their selectivity toward most dangerous heat generating radionuclides (e.g. 137 Cs and 90 Sr) is very important in using

Spontaneous dispersion of PdO onto acid sites of zeolites studied by in situ DXAFS

CERN Document Server

Okumura, K; Niwa, M; Yokota, S; Kato, K; Tanida, H; Uruga, T

2003-01-01

The generation of highly dispersed PdO over zeolite supports was studied using in situ energy-dispersive XAFS (DXAFS) technique. From the comparison with the Na-ZSM-5, it was found that the oxidation as well as the spontaneous dispersion of Pd was promoted through the interaction between PdO and acid sites of H-form zeolites. (author)

New developments in zeolite science and technology

International Nuclear Information System (INIS)

Murakami, Y.

1986-01-01

The contributions in this volume introduce numerous new results and concepts. MAS-NMR has become a powerful tool in the structural analysis of zeolite, metallosilicate and aluminophosphate, enabling definition at the atomic level of the silicon and aluminum forming the zeolite framework. Detailed knowledge on the structure of natural zeolite has increased. Regarding synthesis, studies on the preparation of various metallosilicates, the role of various organic compounds at templates and the kinetics of crystallization and crystal growth are presented. Developments in zeolite catalysts focus not only on the solid-acid catalysts and the shape selective catalysts but on the bifunctional type catalysts as well. Catalyses by metallosilicates or silicoaluminophosphates are reported. Attempts to improve the catalytic performance by modification are presented. Effort is also being devoted to the analysis of adsorption state and diffusion in zeolites. Zeolite deposits of economic value are reported from several countries. (Auth.)

PENJERAPAN P-KHLOROFENOL DALAM AIR LIMBAH DENGAN ZEOLIT (Adsorption of p-Chlorophenol from Wastewater using Zeolite

Directory of Open Access Journals (Sweden)

Sarto Sarto

2007-07-01

Full Text Available ABSTRAK Penelitian ini bertujuan untuk mempelajari kemampuan zeolit untuk menjerap p-khlorofenol dari limbah cair secara batch, pada suhu 30 °C dan tekanan 1 atmosfer. Hasil penelitian menunjukkan bahwa proses penjerapan mengikuti persamaan Freundlich dan bersifat reversibel sebagian. Nisbah kinerja desorbsi dan penjerapan adalah antara 31,85 % dan 49,36 %. Kemampuan zeolit untuk menjerap p-khlorofenol meningkat dengan semakin rendahnya pH. pada nilai pH 3,92, berat zeolit 30 g, dan konsentrasi awal p-khlorofenol 97,302 mg/L. Adapun jumlah p-khlorofenol yang terjerap adalah sebesar 8,319 mg/L.   ABSTRACT The aim of this research is to study the characteristics of zeolit to adsorb p-chlorophenol from wastewater in a batch reactor at 30 oC and atmospheric conditions. The experimental results show that the adsorbtion process is partially reversible and fits with Freundlich Equation. The ratio of  desorption and adsortion performance is between 31.85 % and 49.36 %.  The performance of zeolit to adsorb p-chlorophenol increases with decreasing pH. At  pH about 3.92, using 30 g zeolit and 97.302 mg  p-chlorophenol/L. The concentration of adsorbed p-chlorophenol is about 8.319 mg/L.

Electro-elastoviscous response of polyaniline functionalized nano-porous zeolite based colloidal dispersions.

Science.gov (United States)

Chattopadhyay, Ankur; Rani, Poonam; Srivastava, Rajendra; Dhar, Purbarun

2018-06-01

The present article discusses the typical influence of grafted conducting polymers in the mesoscale pores of dielectric particles on the static and dynamic electrorheology and electro-viscoelastic behavior of corresponding colloids. Nanocrystalline meso-nanoporous zeolite has been prepared by chemical synthesis and subsequently polyaniline (PANI) coating has been implemented. Electrorheological (ER) suspensions have been formed by dispersing the nanoparticles in silicone oil and their viscoelastic behaviors are examined to understand the nature of such complex colloidal systems under electric fields. PANI-Zeolite ER fluids demonstrate higher static electroviscous effects and yield stress potential than untreated Zeolite, typically studied in literature. Transient electro-viscous characterizations show a stable and negligible hysteresis behavior when both the fluids are exposed to constant as well as time varying electric field intensities. Further oscillatory shear experiments of frequency and strain sweeps exhibit predominant elastic behavior in case of Zeolite based ER suspensions as compared to PANI systems. Detailed investigations reveal Zeolite based ER suspensions display enhanced relative yielding as well as electro-viscoelastic stability than the PANI-Zeolite. The steady state viscous behaviors are scaled against the non-dimensional Mason number to model the system behavior for both fluids. Experimental data of flow behaviors of both the ER fluids are compared with semi-classical models and it is found that the CCJ model possesses a closer proximity than traditional Bingham model, thereby revealing the fluids to be generic pseudo-linear fluids. The present article reveals that while the PANI based fluids are typically hailed superior in literature, it is only restricted to steady shear utilities. In case of dynamic and oscillatory systems, the traditional Zeolite based fluids exhibit superior ER caliber. Copyright © 2018 Elsevier Inc. All rights reserved.

Study of activation cross-sections of deuteron induced reactions on rhodium up to 40 MeV

International Nuclear Information System (INIS)

Ditroi, F.; Tarkanyi, F.; Takacs, S.; Hermanne, A.; Yamazaki, H.; Baba, M.; Mohammadi, A.; Ignatyuk, A.V.

2011-01-01

Highlights: → Excitation function measurement of deuteron induced reactions on rhodium up to 40 MeV. → Model code calculations with EMPIRE, ALICE and TALYS. → Integral production yield calculation. → Thin layer activation (TLA) with the produced isotopes. - Abstract: In the frame of a systematic study of the activation cross-sections of deuteron induced nuclear reactions, excitation functions of the 103 Rh(d,x) 100,101,103 Pd, 100g,101m,101g,102m,102g Rh and 103g Ru reactions were determined up to 40 MeV. Cross-sections were measured with the activation method using a stacked foil irradiation technique. Excitation functions of the contributing reactions were calculated using the ALICE-IPPE, EMPIRE-II and TALYS codes. From the measured cross-section data integral production yields were calculated and compared with experimental integral yield data reported in the literature. From the measured cross-sections and previous data, activation curves were deduced to support thin layer activation (TLA) on rhodium and Rh containing alloys.

Comparative solution equilibrium studies on pentamethylcyclopentadienyl rhodium complexes of 2,2'-bipyridine and ethylenediamine and their interaction with human serum albumin.

Science.gov (United States)

Enyedy, Éva A; Mészáros, János P; Dömötör, Orsolya; Hackl, Carmen M; Roller, Alexander; Keppler, Bernhard K; Kandioller, Wolfgang

2015-11-01

Complex formation equilibrium processes of the (N,N) donor containing 2,2'-bipyridine (bpy) and ethylenediamine (en) with (η(5)-pentamethylcyclopentadienyl)rhodium(III) were investigated in aqueous solution via pH-potentiometry, (1)H NMR spectroscopy, and UV-vis spectrophotometry in the absence and presence of chloride ions. The structure of [RhCp*(en)Cl]ClO4 (Cp*, pentamethylcyclopentadienyl) was also studied by single-crystal X-ray diffraction. pKa values of 8.56 and 9.58 were determined for [RhCp*(bpy)(H2O)](2+) and [RhCp*(en)(H2O)](2+), respectively resulting in the formation of negligible amount of mixed hydroxido complexes at pH 7.4. Stability and the H2O/Cl(-) co-ligand exchange constants of bpy and en complexes considerably exceed those of the bidentate O-donor deferiprone. The strong affinity of the bpy and en complexes to chloride ions most probably contributes to their low antiproliferative effect. Interactions between human serum albumin (HSA) and [RhCp*(H2O)3](2+), its complexes formed with deferiprone, bpy and en were also monitored by (1)H NMR spectroscopy, ultrafiltration/UV-vis and spectrofluorometry. Numerous binding sites (≥ 8) are available for [RhCp*(H2O)3](2+); and the interaction takes place most probably via covalent bonds through the imidazole nitrogen of His. According to the various fluorescence studies [RhCp*(H2O)3](2+) binds on sites I and II, and coordination of surface side chain donor atoms of the protein is also feasible. The binding of the bpy and en complex is weaker and slower compared to that of [RhCp*(H2O)3](2+), and formation of ternary HSA-RhCp*-ligand adducts was proved. In the case of the deferiprone complex, the RhCp* fragment is cleaved off when HSA is loaded with low equivalents of the compound.

Sulphide phases in Y zeolite for hydro-treatment reactions; Phase sulfures dans une zeolithe Y pour l'hydrotraitement

Energy Technology Data Exchange (ETDEWEB)

Leyrit, P

1999-06-28

Several types of single (Mo, Co, Pd, Pt) or binary (MoCo, PdCo, PtCo) sulphides phases supported on a HY zeolite were studied. The catalysts were first prepared and characterised in the oxide form. Their reactivity was then evaluated in toluene hydrogenation and 4.6-dimethyl-dibenzo-thiophene hydro-desulfurization reactions. Characterisation of sulphide phases supported on HY zeolite was carried out by elemental analysis, X-Ray Diffraction (XRD), Transmission Electron Microscopy and Scanning Transmission Electron Microscopy (STEM), Extended X-Ray Absorption Fine Structure (EXAFS) and Temperature Programmed Reduction coupled with HS analysis. The results show that. compared with alumina supported catalysts, zeolite used as a support enables extremely active catalysts to be obtained. It appears in particular that molybdenum sulphide phases inside the zeolite have a very high intrinsic activity at low molybdenum content. This activity is attributed to highly dispersed molybdenum sulphide phases differing from MoS{sub 2} slabs and probably present as clusters. The influence of cobalt depends of its concentration. Thus at low loadings cobalt has a strong negative effect. It has been shown, in the molybdenum case, that cobalt interaction leads to an increase in the sulphur content of the molybdenum phases. At higher cobalt loading, the formation of a mixed phase is possible but the degree of promotion remains limited. This work emphasises the advantages of using zeolite supported sulphide phases, and especially Mo and Pd phases, in the hydro-treatment reactions. It seems however that single phases present a greater interest than binary phases. (author)

Metal immobilization in soils using synthetic zeolites

NARCIS (Netherlands)

Osté, L.A.; Lexmond, T.M.; Riemsdijk, van W.H.

2002-01-01

In situ immobilization of heavy metals in contaminated soils is a technique to improve soil quality. Synthetic zeolites are potentially useful additives to bind heavy metals. This study selected the most effective zeolite in cadmium and zinc binding out of six synthetic zeolites (mordenite-type,

Silicalite-1 zeolite membranes on unmodified and modified surfaces

Indian Academy of Sciences (India)

Silicalite-1 zeolite membranes were prepared hydrothermally on the porous ceramic supports, both unmodified and modified with 3-aminopropyl triethoxysilane (APTES) as a coupling agent following ex situ (secondary) crystal growth process. The microstructure of the membranes was examined by scanning electron ...

Comparing gas separation performance between all known zeolites and their zeolitic imidazolate framework counterparts.

Science.gov (United States)

Gómez-Álvarez, Paula; Hamad, Said; Haranczyk, Maciej; Ruiz-Salvador, A Rabdel; Calero, Sofia

2016-01-07

To find optimal porous materials for adsorption-based separations is a challenging task due to the extremely large number of possible pore topologies and compositions. New porous material classes such as Metal Organic Frameworks (MOFs) are emerging, and hope to replace traditionally used materials such as zeolites. Computational screening offers relatively fast searching for candidate structures as well as side-by-side comparisons between material families. This work is pioneering at examining the families comprised by the experimentally known zeolites and their respective Zeolitic Imidazolate Framework (ZIF) counterparts in the context of a number of environmental and industrial separations involving carbon dioxide, nitrogen, methane, oxygen, and argon. Additionally, unlike related published work, here all the targeted structures have been previously relaxed through energy minimization. On the first level of characterization, we considered a detailed pore characterization, identifying 24 zeolites as promising candidates for gas separation based on adsorbate sizes. The second level involved interatomic potential-based calculations to assess the adsorption performance of the materials. We found no correlation in the values of heat of adsorption between zeolites and ZIFs sharing the same topology. A number of structures were identified as potential experimental targets for CO2/N2, and CO2/CH4 affinity-based separations.

Natural zeolites in diet or litter of broilers.

Science.gov (United States)

Schneider, A F; Almeida, D S De; Yuri, F M; Zimmermann, O F; Gerber, M W; Gewehr, C E

2016-04-01

This study aims to analyse the influence of adding natural zeolites (clinoptilolite) to the diet or litter of broilers and their effects on growth performance, carcass yield and litter quality. Three consecutive flocks of broilers were raised on the same sawdust litter, from d 1 to d 42 of age, and distributed in three treatments (control with no added zeolites, addition of 5 g/kg zeolite to diet and addition of 100 g/kg zeolites to litter). The addition of zeolites to the diet or litter did not affect growth performance or carcass yield. The addition of zeolites to the diet did not influence moisture content of the litter, ammonia volatilisation was reduced only in the first flock and pH of litter was reduced in the second and third flock. However, the addition of zeolites to the litter reduced moisture content, litter pH and ammonia volatilisation in all flocks analysed. The addition of 5 g/kg zeolite to the diet in three consecutive flocks was not effective in maintaining litter quality, whereas the addition of 100 g/kg natural zeolites to sawdust litter reduced litter moisture and ammonia volatilisation in three consecutive flocks raised on the same litter.

Methane emissions abatement by multi-ion-exchanged zeolite A prepared from both commercial-grade zeolite and coal fly ash.

Science.gov (United States)

Hui, K S; Chao, C Y H

2008-10-01

The performance of multimetal-(Cu, Cr, Zn, Ni, and Co)-ion-exchanged zeolite A prepared from both a commercial-grade sample and one produced from coal fly ash in methane emissions abatement was evaluated in this study. The ion-exchange process was used to load the metal ions in zeolite A samples. The methane conversion efficiency by the samples was studied under various parameters including the amount of metal loading (7.3-19.4 wt%), reaction temperature (25-500 degrees C), space velocity (8400-41 900 h(-1)), and methane concentration (0.5-3.2 vol %). At 500 degrees C, the original commercial-grade zeolite A catalyzed 3% of the methane only, whereas the addition of different percentages of metals in the sample enhanced the methane conversion efficiency by 40-85%. Greater methane conversion was observed by increasing the percentage of metals added to the zeolite even though the BET surface area of the zeolite consequently decreased. Higher percentage methane conversion over the multi-ion-exchanged samples was observed at lower space velocities indicating the importance of the mass diffusion of reactants and products in the zeolite. Compared to the multi-ion-exchanged zeolite A prepared from the commercial-grade zeolite, the one produced from coal fly ash demonstrated similar performances in methane emissions abatement, showing the potential use of this low cost recycled material in gaseous pollutant treatment.

Computational approach in zeolite science

NARCIS (Netherlands)

Pidko, E.A.; Santen, van R.A.; Chester, A.W.; Derouane, E.G.

2009-01-01

This chapter presents an overview of different computational methods and their application to various fields of zeolite chemistry. We will discuss static lattice methods based on interatomic potentials to predict zeolite structures and topologies, Monte Carlo simulations for the investigation of

Alkali resistant Fe-zeolite catalysts for SCR of NO with NH3 in flue gases

DEFF Research Database (Denmark)

Putluru, Siva Sankar Reddy; Jensen, Anker Degn; Riisager, Anders

2011-01-01

. The effect of potassium doping on the acidic and redox properties of the Fe-zeolite catalysts were studied. The prepared catalysts showed high surface area and surface acidity. This is essential for increased alkali resistivity in comparison with conventional metal oxide supports like, e.g. TiO2 and ZrO2......, towards e.g. potassium salts in flue gases from biomass fired power plants. These properties allowed both undoped and potassium doped Fe-zeolite catalysts to posses high activity during the selective catalytic reduction (SCR) of NO with NH3. The extent of deactivation of the Fe-zeolite catalysts...

Biological effects of simple changes in functionality on rhodium metalloinsertors

Science.gov (United States)

Weidmann, Alyson G.; Komor, Alexis C.; Barton, Jacqueline K.

2013-01-01

DNA mismatch repair (MMR) is crucial to ensuring the fidelity of the genome. The inability to correct single base mismatches leads to elevated mutation rates and carcinogenesis. Using metalloinsertors–bulky metal complexes that bind with high specificity to mismatched sites in the DNA duplex–our laboratory has adopted a new chemotherapeutic strategy through the selective targeting of MMR-deficient cells, that is, those that have a propensity for cancerous transformation. Rhodium metalloinsertors display inhibitory effects selectively in cells that are deficient in the MMR machinery, consistent with this strategy. However, a highly sensitive structure–function relationship is emerging with the development of new complexes that highlights the importance of subcellular localization. We have found that small structural modifications, for example a hydroxyl versus a methyl functional group, can yield profound differences in biological function. Despite similar binding affinities and selectivities for DNA mismatches, only one metalloinsertor shows selective inhibition of cellular proliferation in MMR-deficient versus -proficient cells. Studies of whole-cell, nuclear and mitochondrial uptake reveal that this selectivity depends upon targeting DNA mismatches in the cell nucleus. PMID:23776288

Synthesis of mesoporous zeolite catalysts by in situ formation of carbon template over nickel nanoparticles

DEFF Research Database (Denmark)

Abildstrøm, Jacob Oskar; Kegnæs, Marina; Hytoft, Glen

2016-01-01

A novel synthesis procedure for the preparation of the hierarchical zeolite materials with MFI structure based on the carbon templating method with in situ generated carbon template is presented in this study. Through chemical vapour deposition of coke on nickel nanoparticles supported on silica...... oxide, a carbon-silica composite is obtained and exploited as a combined carbon template/silica source for zeolite synthesis. This approach has several advantages in comparison with conventional carbon templating methods, where relatively complicated preparative strategies involving multistep...... impregnation procedures and rather expensive chemicals are used. Removal of the carbon template by combustion results in zeolite single crystals with intracrystalline pore volumes between 0.28 and 0.48 cm3/g. The prepared zeolites are characterized by XRD, SEM, TEM and physisorption analysis. The isomerization...

The ADOR synthesis of new zeolites: In silico investigation

Czech Academy of Sciences Publication Activity Database

Trachta, Michal; Nachtigal, P.; Bludský, Ota

2015-01-01

Roč. 243, Apr (2015), s. 32-38 ISSN 0920-5861 R&D Projects: GA ČR GBP106/12/G015 Institutional support: RVO:61388963 Keywords : ADOR * DFT calculations * zeolites * synthesis Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 4.312, year: 2015

Limestone and Zeolite as Alternative Media in Horizontal Subsurface Flow Constructed Wetlands: Laboratory-Scale Studies

Science.gov (United States)

Lizama, K.; Jaque, I.; Ayala, J.

2016-12-01

Arsenic is well known for its chronic toxicity. Millions of people around the world are currently at risk, drinking water with As concentrations above 10 ppb, the WHO drinking water guideline. Although different treatment options exist, they are often limited by elevated costs and maintenance requirements. Constructed wetlands are a natural water treatment system, capable to remove metals and metalloids -including As- via different physical, chemical and biological processes. The use of alternative supporting media to enhance As removal in subsurface flow wetlands has been recommended, but not sufficiently studied. Limestone and zeolite have been identified as effective supporting media in subsurface flow wetlands aiming As removal. However, there are still key aspects to be addressed, such as the implications of using these media, the speciation in the solid phase, the role of vegetation, etc. This study investigated the performance of limestone and zeolite in three types of experiments: batch, column and as main supporting media in a bench scale horizontal subsurface flow wetland system. Synthetic water resembling a contaminated river in Chile (As concentration=3 mg/L, Fe concentration= 100 mg/L, pH=2) was used in all experiments. In the batch experiments, the As concentration, the mass of media and the contact time were varied. The column system consisted of three limestone columns and three zeolite columns, operated under a hydraulic loading of 20 mm/d. The wetland system consisted of twelve PVC cells: six filled with zeolite and six with limestone. Phragmites australis were planted in three cells of each media type, as control cells. From the batch experiments, maximum As sorption capacities as indicated by Langmuir model were 1.3 mg/g for limestone and 0.17 mg/g for zeolite, at 18 h contact time and 6.3 g/L medium concentration. EDS and XPS analyses revealed that As and Fe were retained in zeolite at the end of the batch experiments. Zeolite and limestone

Enantioselective rhodium/ruthenium photoredox catalysis en route to chiral 1,2-aminoalcohols.

Science.gov (United States)

Ma, Jiajia; Harms, Klaus; Meggers, Eric

2016-08-09

A rhodium-based chiral Lewis acid catalyst combined with [Ru(bpy)3](PF6)2 as a photoredox sensitizer allows for the visible-light-activated redox coupling of α-silylamines with 2-acyl imidazoles to afford, after desilylation, 1,2-amino-alcohols in yields of 69-88% and with high enantioselectivity (54-99% ee). The reaction is proposed to proceed via an electron exchange between the α-silylamine (electron donor) and the rhodium-chelated 2-acyl imidazole (electron acceptor), followed by a stereocontrolled radical-radical reaction. Substrate scope and control experiments reveal that the trimethylsilyl group plays a crucial role in this reductive umpolung of the carbonyl group.

A general method to incorporate metal nanoparticles in zeolites and zeotypes

DEFF Research Database (Denmark)

2015-01-01

Disclosed herein is a method for producing a zeolite, zeolite-like or zeotype structure with selective formation of metal, metal oxide or metal sulphide nanoparticles and/or clusters inside the zeolite, zeolite-like or zeotype structure.......Disclosed herein is a method for producing a zeolite, zeolite-like or zeotype structure with selective formation of metal, metal oxide or metal sulphide nanoparticles and/or clusters inside the zeolite, zeolite-like or zeotype structure....

Zeolite-derived hybrid materials with adjustable organic pillars

Czech Academy of Sciences Publication Activity Database

Opanasenko, Maksym; Shamzhy, Mariya; Yu, F.; Zhou, W.; Morris, R. E.; Čejka, Jiří

2016-01-01

Roč. 7, č. 6 (2016), s. 3589-3601 ISSN 2041-6520 R&D Projects: GA ČR GP13-17593P; GA ČR GBP106/12/G015 Institutional support: RVO:61388955 Keywords : zeolites * inorganic aluminosilicate * nanoporous materials Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 8.668, year: 2016

Alkali-activated blast furnace slag-zeolite cements and concretes

International Nuclear Information System (INIS)

Rakhimov, R.; Rakhimova, N.

2012-01-01

The aim of this work has been the study of alkali-activated slag-zeolite cements and concretes based on them. Various compositions have been tested and some characteristics such as the compressive strength have been measured versus zeolite additions. A table lists the specific surface area and particle size distributions of different cements. The conclusions of the study are the following. First, alkali-activated slag cements and concretes based on them are effective for immobilization of radioactive wastes and the production of building structures, designed for high radiation load. Secondly, zeolite-containing mineral additions are able to increase the immobilization capacity and radiation resistance of alkali-activated blast furnace slag cements and concretes. Thirdly, the efficiency of different zeolite-containing additions - 10% to increase alkali-activated blast furnace slag-zeolite cement strength was established. It is with alkaline components of water-glass, sodium carbonate, sodium sulphate. Fourth, the effective way of introducing zeolite additions in alkali-activated blast furnace slag-zeolite cement is inter-grinding of the slag and addition. Increase in strength of alkali-activated blast furnace slag-zeolite cement stone is 40% higher than that of the stone of a mixture of separately milled components. Fifth, Alkali-activated blast furnace slag-zeolite cements with zeolite-containing additions with a compressive strength of 10.1 to 140 MPa; alkali-activated blast furnace slag-zeolite cements mortars with compressive strength from 35.2 to 97.7 MPa; alkali-activated blast furnace slag-zeolite cements concretes with compressive strength up to 84.5 MPa and frost resistant up to 800 cycles were obtained

Effect of Ge/Si substitutions on the local geometry of Si framework sites in zeolites: A combined high resolutionsup29/supSi MAS NMR and DFT/MM study on zeolite Beta polymorph C (BEC)

Czech Academy of Sciences Publication Activity Database

Whittleton, Sarah R.; Vicente, A.; Fernandez, C.; Rastegar, Somayeh F.; Fishchuk, Anna V.; Sklenák, Štěpán

2018-01-01

Roč. 267, SEP 2018 (2018), s. 124-133 ISSN 1387-1811 R&D Projects: GA ČR(CZ) GA15-14007S Grant - others:Ga MŠk(CZ) LM2015070 Institutional support: RVO:61388955 Keywords : 29 Si MAS NMR * bec * Ge-zeolites * Germanoaluminosilicates * Zeolite Beta polymorph C Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 3.615, year: 2016

Vitrification of highly-loaded SDS zeolites

International Nuclear Information System (INIS)

Siemens, D.H.; Bryan, G.H.; Knowlton, D.E.; Knox, C.A.

1982-11-01

Pacific Northwest Laboratory (PNL) is demonstrating a vitrification system designed for immobilization of highly loaded SDS zeolites. The Zeolite Vitrification Demonstration Project (ZVDP) utilizes an in-can melting process. All steps of the process have been demonstrated, from receipt of the liners through characterization of the vitrified product. The system has been tested with both nonradioactive and radioactive zeolite material. Additional high-radioactivity demonstrations are scheduled to begin in FY-83. 5 figures, 4 tables

Chemical reactivity of cation-exchanged zeolites

OpenAIRE

Pidko, E.A.

2008-01-01

Zeolites modified with metal cations have been extensively studied during the last two decades because of their wide application in different technologically important fields such as catalysis, adsorption and gas separation. Contrary to the well-understood mechanisms of chemical reactions catalyzed by Brønsted acid sites in the hydrogen forms of zeolites, the nature of chemical reactivity, and related, the structure of the metal-containing ions in cation-exchanged zeolites remains the subject...

Catalase-like activity studies of the manganese(II) adsorbed zeolites

Science.gov (United States)

Ćiçek, Ekrem; Dede, Bülent

2013-12-01

Preparation of manganese(II) adsorbed on zeolite 3A, 4A, 5A. AW-300, ammonium Y zeolite, organophilic, molecular sieve and catalase-like enzyme activity of manganese(II) adsorbed zeolites are reported herein. Firstly zeolites are activated at 873 K for two hours before contact manganese(II) ions. In order to observe amount of adsorption, filtration process applied for the solution. The pure zeolites and manganese(II) adsorbed zeolites were analysed by FT-IR. As a result according to the FT-IR spectra, the incorporation of manganese(II) cation into the zeolite structure causes changes in the spectra. These changes are expected particularly in the pseudolattice bands connected with the presence of alumino and silicooxygen tetrahedral rings in the zeolite structure. Furthermore, the catalytic activities of the Mn(II) adsorbed zeolites for the disproportionation of hydrogen peroxide were investigated in the presence of imidazole. The Mn(II) adsorbed zeolites display efficiency in the disproportion reactions of hydrogen peroxide, producing water and dioxygen in catalase-like activity.

Redox behavior of transition metal ions in zeolites 6. Reversibility of the reduction reaction in silver zeolites

Energy Technology Data Exchange (ETDEWEB)

Jacobs, P A; Uytterhoeven, J B; Beyer, H K

1977-01-01

Degassing above 573/sup 0/K of Ag-Y or Ag-mordenite previously reduced by hydrogen at 623/sup 0/K resulted in hydrogen evolution, the amount of hydrogen increasing to a maximum at about 873/sup 0/K. No hydrogen was evolved when the zeolite was reduced by hydrazine or hydroxylamine, indicating that hydrogen is formed by reaction between silver metal and hydroxyl groups formed in the reduction step (i.e., the reverse of the reduction step). Consumption of hydroxyl groups was proven by IR studies of pyridine chemisorption which occurs entirely as pyridinium ions on Broensted sites or reduced samples but with increasing formation of pyridine on Lewis acid sites as the degassing temperature increases; formation of silver(I) ions was proven by carbon monoxide complexation. Silver metal outside the zeolite pores was not affected by the degassing, and the amount of hydrogen evolved upon degassing decreased with increasing number of reduction-degassing cycles, probably as a result of dehydroxylation or sintering. Spectra, graphs, tables, and 21 references.

AKTIVASI ZEOLIT ALAM SEBAGAI ADSORBEN PADA ALAT PENGERING BERSUHU RENDAH

Directory of Open Access Journals (Sweden)

Laeli Kurniasari

2012-04-01

Full Text Available ACTIVATION OF NATURAL ZEOLITE AS AN ADSORBENT FOR LOW TEMPERATURE DRYING SYSTEM. Drying is one process which is used in many industries, especially in food product. The process usually still has low energy efficiency and can make food deterioration because of the usage of high temperature. One alternative in drying technology is the use of zeolite as a water vapor adsorbent. This kind of drying method make it possible to operate in lower temperature, hence it will be suitable for heat sensitive product. Natural zeolit can be one promising adsorbent since it is spreadly abundant in Indonesia. Natural zeolite must be activated first before used, in order to get zeolite with high adsorption capacity. Activation process in natural zeolite will change the Si/Al ratio, polarity, and affinity of zeolite toward water vapor and also increase the porosity. Activation of natural zeolite can be done with two methods, chemical activation use NaOH and physical activation use heat. In the activation using NaOH, natural zeolite is immersed with NaOH solution 0.5-2N in 2 hour with temperature range 60-900C. The process is continued with the drying of zeolite in oven with 1100C for 4 hours. While in heat treatment, zeolit is heated into 200-5000C in furnace for 2-5 hours. SEM analysis is used to compare the change in zeolite morphology before and after each treatment, while to know the adsorption capacity of zeolite, the analyses were done in many temperature and relative humidity. Result gives the best condition in NaOH activation is NaOH 1N and temperature 700C, with water vapor loading is 0.171 gr/gr adsorbent. In heat treatment, the best condition is 3000C and 3 hours with loading 0.137 gr water vapor/gr adsorbent.  Pengeringan merupakan salah satu proses yang banyak digunakan pada produk pangan. Proses ini umumnya menyebabkan kerusakan pada bahan pangan, disamping masih rendahnya efisiensi energi. Salah satu alternatif pada proses pengeringan yaitu

Sulphide phases in Y zeolite for hydro-treatment reactions; Phase sulfures dans une zeolithe Y pour l'hydrotraitement

Energy Technology Data Exchange (ETDEWEB)

Leyrit, P.

1999-06-28

Several types of single (Mo, Co, Pd, Pt) or binary (MoCo, PdCo, PtCo) sulphides phases supported on a HY zeolite were studied. The catalysts were first prepared and characterised in the oxide form. Their reactivity was then evaluated in toluene hydrogenation and 4.6-dimethyl-dibenzo-thiophene hydro-desulfurization reactions. Characterisation of sulphide phases supported on HY zeolite was carried out by elemental analysis, X-Ray Diffraction (XRD), Transmission Electron Microscopy and Scanning Transmission Electron Microscopy (STEM), Extended X-Ray Absorption Fine Structure (EXAFS) and Temperature Programmed Reduction coupled with HS analysis. The results show that. compared with alumina supported catalysts, zeolite used as a support enables extremely active catalysts to be obtained. It appears in particular that molybdenum sulphide phases inside the zeolite have a very high intrinsic activity at low molybdenum content. This activity is attributed to highly dispersed molybdenum sulphide phases differing from MoS{sub 2} slabs and probably present as clusters. The influence of cobalt depends of its concentration. Thus at low loadings cobalt has a strong negative effect. It has been shown, in the molybdenum case, that cobalt interaction leads to an increase in the sulphur content of the molybdenum phases. At higher cobalt loading, the formation of a mixed phase is possible but the degree of promotion remains limited. This work emphasises the advantages of using zeolite supported sulphide phases, and especially Mo and Pd phases, in the hydro-treatment reactions. It seems however that single phases present a greater interest than binary phases. (author)

Absorption behavior of iodine from molten salt mixture to zeolite

International Nuclear Information System (INIS)

Sugihara, Kei; Terai, Takayuki; Suzuki, Akihiro; Uozumi, Koichi; Tsukada, Takeshi; Koyama, Tadafumi

2011-01-01

Behavior of zeolite to absorb anion fission product (FP) elements in molten LiCl-KCl eutectic salt was studied using iodine. At first, zeolite-A was selected as the suitable type of zeolite among zeolite-A (powder), zeolite-X (powder and granule), and zeolite-Y (powder) through experiments to heat the zeolite together with LiCl-KCl-KI salt, respectively. As the next step, similar experiments to immerse zeolite-A in molten LiCl-KCl-KI salt containing various concentrations of iodine were performed. The affinity of iodine to zeolite was evaluated using the separation factor (SF) value, which is defined as [I/(I+Cl) mol ratio in zeolite after immersion]/[I/(I+Cl) mol ratio in salt after immersion]. Since the SF values ranged between 4.3 and 9.1, stronger affinity of iodine than chlorine to zeolite-A was revealed. Finally, influence of co-existing cation FPs was studied by similar absorption experiments in LiCl-KCl-KI salt containing CsCl, SrCl 2 , or NdCl 3 . The SF values were less than those obtained in the LiCl-KCl-KI salt and this can be ascribed to the sharing of inner space of zeolite cage among absorbed cations and anions. (author)

A Concise Synthesis of the Erythrina Alkaloid 3–Demethoxyerythratidinone via Combined Rhodium Catalysis

Science.gov (United States)

Joo, Jung Min; David, Ramoncito A.; Yuan, Yu; Lee, Chulbom

2010-01-01

The total synthesis of the erythrina alkaloid 3–demethoxyerythratidinone has been achieved via a strategy based on combined rhodium catalysis. The catalytic tandem cyclization effected by the interplay of alkynyl and vinylidene rhodium species allows for efficient access to the A and B rings of the tetracyclic erythrinane skeleton in a single step. The synthesis also features rapid preparation of the requisite precursor for the double ring closure and thus has been completed in only 7 total steps in 41% overall yield. PMID:21090648

THE EFFECT OF TYPE ZEOLITE ON THE GAS TRANSPORT PROPERTIES OF POLYIMIDE-BASED MIXED MATRIX MEMBRANES

Directory of Open Access Journals (Sweden)

Tutuk Djoko Kusworo

2012-01-01

Full Text Available The permeation rates of O2, N2, CO2 and CH4 has been studied for polyimide-polyethersulfone (PI/PES blends-zeolite mixed matrix membranes synthesized in our laboratory. The study investigated the effect of zeolite loading and different zeolite type on the gas separation performance of these mixed matrix membranes. Frequency shifts and absorption intensity changes in the FTIR spectra of the PI/PES blends as compared with those of the pure polymers indicate that there is a mixing of polymer blends at the molecular level. Differential scanning calorimetry measurements of pure and PI/PES blends membranes have showed one unique glass transition temperature that supports the miscible character of the PI/PES mixture. The PI/PES-zeolite 4A mixed matrix membrane with 25 wt % zeolite loading produced the highest O2/N2 and CO2/CH4 selectivity of around 7.45 and 46.05, respectively.

Structure of a Rh/TiO2 catalyst in the strong metal-support interaction state as determined by EXAFS

International Nuclear Information System (INIS)

Koningsberger, D.C.; Martens, J.H.A.; Prins, R.; Short, D.R.; Sayers, D.E.

1986-01-01

Reduction of a highly dispersed 2.85 wt% Rh/TiO 2 catalyst at 473 K after previous calcination at 623 K resulted in EXAFS whose primary contributions are due to nearest rhodium (average coordination number of 3.1 and distance of 2.67 A) and oxygen neighbors (coordination 2.5 and distance 2.71 A). These oxygen neighbors originated at the metal-support interface. The average rhodium-rhodium coordination number did not change in the SMSI state produced by reducing the catalyst at 673 K. However, the average coordination distance contracted by 0.04 A with an accompanying decrease of the Debye-Waller factor of the Rh-Rh bond of 0.0012 A 2 . This is due to the fact that in the SMSI state the surface of the metal particles is not covered with chemisorbed hydrogen. The SMSI state leads to a structural reorganization of the support in the vicinity of the rhodium metal particles. This can be concluded from the appearance of a Rh-Ti bond at 3.42 A in the SMSI state coupled with the fact that the average coordination number of the rhodium-support oxygen bonds does not increase. Other types of rhodium-oxygen bonds could not be detected with EXAFS in this state. Thus, these results provide no evidence for coverage of the metal particle by a suboxide of TiO 2 in the SMSI state

Hydrogen Selective Exfoliated Zeolite Membranes

Energy Technology Data Exchange (ETDEWEB)

Tsapatsis, Michael [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Daoutidis, Prodromos [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Elyassi, Bahman [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Lima, Fernando [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Iyer, Aparna [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Agrawal, Kumar [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science; Sabnis, Sanket [Univ. of Minnesota, Minneapolis, MN (United States). Department of Chemical Engineering and Materials Science

2015-04-06

The objective of this project was to develop and evaluate an innovative membrane technology at process conditions that would be representative of Integrated Gasification Combined Cycle (IGCC) advanced power generation with pre-combustion capture of carbon dioxide (CO₂). This research focused on hydrogen (H₂)-selective zeolite membranes that could be utilized to separate conditioned syngas into H₂-rich and CO₂-rich components. Both experiments and process design and optimization calculations were performed to evaluate the concept of ultra-thin membranes made from zeolites nanosheets. In this work, efforts in the laboratory were made to tackle two fundamental challenges in application of zeolite membranes in harsh industrial environments, namely, membrane thickness and membrane stability. Conventional zeolite membranes have thicknesses in the micron range, limiting their performance. In this research, we developed a method for fabrication of ultimately thin zeolite membranes based on zeolite nanosheets. A range of layered zeolites (MWW, RWR, NSI structure types) suitable for hydrogen separation was successfully exfoliated to their constituent nanosheets. Further, membranes were made from one of these zeolites, MWW, to demonstrate the potential of this group of materials. Moreover, long-term steam stability of these zeolites (up to 6 months) was investigated in high concentrations of steam (35 mol% and 95 mole%), high pressure (10 barg), and high temperatures (350 °C and 600 °C) relevant to conditions of water-gas-shift and steam methane reforming reactions. It was found that certain nanosheets are stable, and that stability depends on the concentration of structural defects. Additionally, models that represent a water-gas-shift (WGS) membrane reactor equipped with the zeolite membrane were developed for systems studies. These studies had the aim of analyzing the effect of the membrane reactor integration into IGCC plants

Progress on Zeolite-membrane-aided Organic Acid Esterification

Science.gov (United States)

Makertiharta, I. G. B. N.; Dharmawijaya, P. T.

2017-07-01

Esterification is a common route to produce carboxylic acid esters as important intermediates in chemical and pharmaceutical industries. However, the reaction is equilibrium limited and needs to be driven forward by selective removal one of the products. There have been some efforts to selectively remove water from reaction mixture via several separation processes (such as pervaporation and reactive distillation). Integrated pervaporation and esterification has gained increasing attention towards. Inorganic zeolite is the most popular material for pervaporation due to its high chemical resistant and separation performance towards water. Zeolite also has proven to be an effective material in removing water from organic compound. Zeolite can act not only as selective layer but also simultaneously act as a catalyst on promoting the reaction. Hence, there are many configurations in integrating zeolite membrane for esterification reaction. As a selective layer to remove water from reaction mixture, high Si/Al zeolite is preferred to enhance its hydrophilicity. However, low Si/Al zeolite is unstable in acid condition due to dealumination thus eliminate its advantages. As a catalyst, acid zeolites (e.g. H-ZSM-5) provide protons for autoprotolysis of the carboxylic acid similar to other catalyst for esterification (e.g. inorganic acid, and ion exchange resins). There are many studies related to zeolite membrane aided esterification. This paper will give brief information related to zeolite membrane role in esterification and also research trend towards it.

ZEOLITIZATION OF SEWAGE SLUDGE ASH WITH A FUSION METHOD

Directory of Open Access Journals (Sweden)

Jolanta Latosińska

2016-11-01

Full Text Available The study shows the results of zeolitization of municipal sewage sludge ash with the indirect fusion method followed by a hydrothermal method. The zeolitization of sewage sludge ash was conducted at the melting temperature of 550°C and the melting time of 60 minutes, crystallization temperatures of 60°C and 90°C, crystallization time of 6 hours and the SSA:NaOH ratio of 1:1.8; 1:1.4. The research of modified sewage sludge ashes included the observation of changes of ash particles surface and the identification of crystalized phases. The zeolitization of sewage sludge ash at the ratio of SSA:NaOH 1.0:1.4 did not cause the formation of zeolite phases. On the other hand, the zeolitization at the ratio of SSA:NaOH 1.0:1.8 resulted in the formation of desired zeolite phases such as zeolite Y (faujasite and hydroxysodalite. The presented method of sewage sludge ash zeolitization allows to obtain highly usable material. Synthesized zeolites may be used as adsorbents and ion exchangers. They can be potentially used to remove heavy metals as well as ammonia from water and wastewater.

Preparation of Synthetic Zeolites from Myanmar Clay Mineral

International Nuclear Information System (INIS)

Phyu Phyu Win

2004-04-01

Faujasite type zeolite X was successfully synthesized from Myanmar clay mineral kaolinite, by treating with sodium hydroxide at 820 C followed by dissolution in water and hydrothermal treatment. It was found that the solution of fused clay powder can be crystallized at 90C under ambient pressure to synthesize faujasite type zeolite X. The effects of aging time and the amount of water on the formation of the product phase and Si/ Al ratios of the resulting products were investigated. Most of the Si and Al components in kaolinite might be dissolved into an alkaline solution and reacted to form ring-like structures. Then it was effectively transformed into zeolite materials. The maximum relative crystallinity of faujasite zeolite obtained was found to be 100%. Zeolite P was found to be a competitive phase present in some resulting products during hydrothermal treatment. The cation exchange capacity of kaolinite is very low, but increased after a proper treatment. It was found that the prepared faujasite type zeolite X, zeolite P and hydrogen zeolite (HZ) can reduce the hardness, the alkalinity, the total dissolved solid and the dissolved iron of raw water in the batch wise operation of water treatment. Therefore, it can be used as the cation exchanged resin for water treatment

Supported ionic liquid-phase (SILP) catalysis

DEFF Research Database (Denmark)

Riisager, Anders; Fehrmann, Rasmus; Wasserscheid, P.

2005-01-01

The concept of supported ionic liquid-phase (SILP) catalysis has been demonstrated for gas- and liquid-phase continuous fixed-bed reactions using rhodium phosphine catalyzed hydroformylation of propene and 1-octene as examples. The nature of the support had important influence on both the catalytic...

Strong white photoluminescence from annealed zeolites

International Nuclear Information System (INIS)

Bai, Zhenhua; Fujii, Minoru; Imakita, Kenji; Hayashi, Shinji

2014-01-01

The optical properties of zeolites annealed at various temperatures are investigated for the first time. The annealed zeolites exhibit strong white photoluminescence (PL) under ultraviolet light excitation. With increasing annealing temperature, the emission intensity of annealed zeolites first increases and then decreases. At the same time, the PL peak red-shifts from 495 nm to 530 nm, and then returns to 500 nm. The strongest emission appears when the annealing temperature is 500 °C. The quantum yield of the sample is measured to be ∼10%. The PL lifetime monotonously increases from 223 μs to 251 μs with increasing annealing temperature. The origin of white PL is ascribed to oxygen vacancies formed during the annealing process. -- Highlights: • The optical properties of zeolites annealed at various temperatures are investigated. • The annealed zeolites exhibit strong white photoluminescence. • The maximum PL enhancement reaches as large as 62 times. • The lifetime shows little dependence on annealing temperature. • The origin of white emission is ascribed to the oxygen vacancies

Reaction mechanisms in zeolite catalysis

NARCIS (Netherlands)

Rozanska, X.; Santen, van R.A.; Auerbach, S.C.; Carrado, K.A.; Dutta, P.D.

2003-01-01

A review; described are the most basic mechanistic reaction steps that are induced by zeolite catalysts. Details on the zeolitic properties that are relevant to mol. reactivity are also provided. The theor. methods and models at hand to allow the investigation of these reaction steps and that have

Exposure of the German general population to platinum and rhodium - Urinary levels and determining factors.

Science.gov (United States)

Munker, Sven; Kilo, Sonja; Röß, Christoph; Jeitner, Peter; Schierl, Rudolf; Göen, Thomas; Drexler, Hans

2016-11-01

In this study the exposure of the general population in Germany to platinum and rhodium and its determinants was investigated in 259 participants (subdivided in three groups) by urine analyses and assessment of the dental status. Complementary, an interview including questions characterising possible exposure to traffic exhaust was conducted. The median excretion was 2.42ng platinum/g creatinine and 7.27ng rhodium/g creatinine. The detailed analysis of the collected data showed significant higher platinum excretion values with increasing number of surfaces covered with restorations containing precious metals (R=0.389; prhodium excretion values (median=7.27ng/g; 95th percentile=13.5 ng/g). In summary, the study showed that exhaust emissions have an influence on platinum and rhodium excretion, but for platinum this influence is rather low compared to the influence of precious metals containing restorations. Copyright © 2016 Elsevier GmbH. All rights reserved.

Electrical conductivity of polyaniline/zeolite composites and synergetic interaction with CO

International Nuclear Information System (INIS)

Densakulprasert, Nataporn; Wannatong, Ladawan; Chotpattananont, Datchanee; Hiamtup, Piyanoot; Sirivat, Anuvat; Schwank, Johannes

2005-01-01

The effects of zeolite content, pore size and ion exchange capacity on electrical conductivity response to carbon monoxide (CO) of polyaniline/zeolite composites were investigated. Zeolite Y, 13X, and synthesized AlMCM41, all having the common cation Cu 2+ , were dry mixed with synthesized maleic acid (MA) doped polyaniline and compressed to form polyaniline (PANI)/zeolite pellet composites. The Y, 13X and AlMCM41 zeolite have the nominal pore sizes of 7, 10, 36 A, and the Cu 2+ exchange capacities of 0.161, 0.087, and 0.044 mol/g, respectively. With an addition of 13X zeolite to pristine polyaniline, the electrical conductivity sensitivity to CO/N 2 gas increases with zeolite content. For the effect of zeolite type, the highest electrical conductivity sensitivity is obtained with the 13X zeolite, followed by the Y zeolite, and the AlMCM41 zeolite, respectively. Poor sensitivity of zeolite AlMCM41 is probably due to its very large pore size and its lowest Cu 2+ exchange capacity. Y zeolite and 13X zeolite have comparable pore sizes but the latter has a greater pore free volume and a more favorable location distribution of the Cu 2+ ions within the pore. The temporal response time increases with the amount of zeolite in the composites but it is inversely related to the amount of ion exchange capacity

Development of spent salt treatment technology by zeolite column system. Performance evaluation of zeolite column

International Nuclear Information System (INIS)

Miura, Hidenori; Uozumi, Koichi

2009-01-01

At electrorefining process, fission products(FPs) accumulate in molten salt. To avoid influence on heating control by decay heat and enlargement of FP amount in the recovered fuel, FP elements must be removed from the spent salt of the electrorefining process. For the removal of the FPs from the spent salt, we are investigating the availability of zeolite column system. For obtaining the basic data of the column system, such as flow property and ion-exchange performance while high temperature molten salt is passing through the column, and experimental apparatus equipped with fraction collector was developed. By using this apparatus, following results were obtained. 1) We cleared up the flow parameter of column system with zeolite powder, such as flow rate control by argon pressure. 2) Zeolite 4A in the column can absorb cesium that is one of the FP elements in molten salt. From these results, we got perspective on availability of the zeolite column system. (author)

Zeolite food supplementation reduces abundance of enterobacteria.

Science.gov (United States)

Prasai, Tanka P; Walsh, Kerry B; Bhattarai, Surya P; Midmore, David J; Van, Thi T H; Moore, Robert J; Stanley, Dragana

2017-01-01

According to the World Health Organisation, antibiotics are rapidly losing potency in every country of the world. Poultry are currently perceived as a major source of pathogens and antimicrobial resistance. There is an urgent need for new and natural ways to control pathogens in poultry and humans alike. Porous, cation rich, aluminosilicate minerals, zeolites can be used as a feed additive in poultry rations, demonstrating multiple productivity benefits. Next generation sequencing of the 16S rRNA marker gene was used to phylogenetically characterize the fecal microbiota and thus investigate the ability and dose dependency of zeolite in terms of anti-pathogenic effects. A natural zeolite was used as a feed additive in laying hens at 1, 2, and 4% w/w for a 23 week period. At the end of this period cloacal swabs were collected to sample faecal microbial communities. A significant reduction in carriage of bacteria within the phylum Proteobacteria, especially in members of the pathogen-rich family Enterobacteriaceae, was noted across all three concentrations of zeolite. Zeolite supplementation of feed resulted in a reduction in the carriage of a number of poultry pathogens without disturbing beneficial bacteria. This effect was, in some phylotypes, correlated with the zeolite concentration. This result is relevant to zeolite feeding in other animal production systems, and for human pathogenesis. Copyright © 2016 Elsevier GmbH. All rights reserved.

First application of supported ionic liquid phase (SILP) catalysis for continuous methanol carbonylation

DEFF Research Database (Denmark)

Riisager, Anders; Jørgensen, Betina; Wasserscheid, Peter

2006-01-01

A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)(2)I-2]-[BMIM]I -SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation.......A solid, silica-supported ionic liquid phase (SILP) rhodium iodide Monsanto-type catalyst system, [BMIM][Rh(CO)(2)I-2]-[BMIM]I -SiO2, exhibits excellent activity and selectivity towards acetyl products in fixed-bed, continuous gas-phase methanol carbonylation....

Adsorption Cooling System Using Metal-Impregnated Zeolite-4A

Directory of Open Access Journals (Sweden)

Somsuk Trisupakitti

2016-01-01

Full Text Available The adsorption cooling systems have been developed to replace vapor compression due to their benefits of being environmentally friendly and energy saving. We prepared zeolite-4A and experimental cooling performance test of zeolite-water adsorption system. The adsorption cooling test-rig includes adsorber, evaporator, and condenser which perform in vacuum atmosphere. The maximum and minimum water adsorption capacity of different zeolites and COP were used to assess the performance of the adsorption cooling system. We found that loading zeolite-4A with higher levels of silver and copper increased COP. The Cu6%/zeolite-4A had the highest COP at 0.56 while COP of zeolite-4A alone was 0.38. Calculating the acceleration rate of zeolite-4A when adding 6% of copper would accelerate the COP at 46%.

An operando FTIR spectroscopic and kinetic study of carbon monoxide pressure influence on rhodium-catalyzed olefin hydroformylation.

Science.gov (United States)

Kubis, Christoph; Sawall, Mathias; Block, Axel; Neymeyr, Klaus; Ludwig, Ralf; Börner, Armin; Selent, Detlef

2014-09-08

The influence of carbon monoxide concentration on the kinetics of the hydroformylation of 3,3-dimethyl-1-butene with a phosphite-modified rhodium catalyst has been studied for the pressure range p(CO)=0.20-3.83 MPa. Highly resolved time-dependent concentration profiles of the organometallic intermediates were derived from IR spectroscopic data collected in situ for the entire olefin-conversion range. The dynamics of the catalyst and organic components are described by enzyme-type kinetics with competitive and uncompetitive inhibition reactions involving carbon monoxide taken into account. Saturation of the alkyl-rhodium intermediates with carbon monoxide as a cosubstrate occurs between 1.5 and 2 MPa of carbon monoxide pressure, which brings about a convergence of aldehyde regioselectivity. Hydrogenolysis of the acyl intermediate is fast at 30 °C and low pressure of p(CO)=0.2 MPa, but is of minus first order with respect to the solution concentration of carbon monoxide. Resting 18-electron hydrido and acyl complexes that correspond to early and late rate-determining states, respectively, coexist as long as the conversion of the substrate is not complete. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrochemical behavior of rhodium acetamidate immobilized on a carbon paste electrode: a hydrazine sensor

Directory of Open Access Journals (Sweden)

Gil Eric de S.

2000-01-01

Full Text Available The electrochemical behavior of rhodium acetamidate immobilized in carbon paste electrode and the consequences for sensor construction were evaluated. The electrode showed good stability and redox properties. Two reversible redox couples with midpoint potentials between 0.15 and 0.55 V vs SCE were observed. However, peak resolution in voltammetric studies was very dependent on the supporting electrolyte. The correlation between coordinating power of the electrolyte and peak potential suggests that the electrolyte can coordinate through the axial position of the complexes. Furthermore, the axial position may be also the catalytic site, as a catalytical response was observed for hydrazine oxidation. A good linear response range for hydrazine was fit by the equation i = 23.13 (± 0.34 c , where i = current in mA and c = concentration in mol dm-3 in the range of 10-5 up to 10-2 mol dm-3. The low applied potential (<300 mV indicates a good device for hydrazine sensor, minimizing interference problems. The short response time (~1 s may be useful in flow injection analysis. Furthermore, this system was very stable presenting good repeatability even after 30 measurements with a variance of 0.5 %.

Natural zeolite reactivity towards ozone: The role of compensating cations

International Nuclear Information System (INIS)

Valdés, Héctor; Alejandro, Serguei; Zaror, Claudio A.

2012-01-01

Highlights: ► Chemical and thermal treatment enhances catalytic activity of natural zeolite. ► Modified natural zeolite exhibits high stability after thermal treatment. ► Reducing the compensating cation content leads to an increase on ozone abatement. ► Surface active atomic oxygen was detected using the DRIFT technique. ► The highest reactivity toward ozone was performed by NH4Z3 zeolite sample. - Abstract: Among indoor pollutants, ozone is recognised to pose a threat to human health. Recently, low cost natural zeolites have been applied as alternative materials for ozone abatement. In this work, the effect of compensating cation content of natural zeolite on ozone removal is studied. A Chilean natural zeolite is used here as starting material. The amount of compensating cations in the zeolite framework was modified by ion exchange using an ammonium sulphate solution (0.1 mol L −1 ). Characterisation of natural and modified zeolites were performed by X-ray powder diffraction (XRD), nitrogen adsorption at 77 K, elemental analysis, X-ray fluorescence (XRF), thermogravimetric analysis coupled with mass spectroscopy (TGA-MS), and temperature-programmed desorption of ammonia (NH 3 -TPD). Ozone adsorption and/or decomposition on natural and modified zeolites were studied by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Results show that the zeolite compensating cation content affects ozone interaction with zeolite active sites. Ammonium ion-exchange treatments followed by thermal out-gassing at 823 K, reduces ozone diffusion resistance inside the zeolite framework, increasing ozone abatement on zeolite surface active sites. Weak and strong Lewis acid sites of zeolite surface are identified here as the main active sites responsible of ozone removal.

Electrodeposition of carrier-free 57Co on rhodium as an approach to the preparation of Moessbauer sources

International Nuclear Information System (INIS)

Cieszykowska, Izabela; ZoLtowska, MaLgorzata; Mielcarski, MieczysLaw

2011-01-01

Electrodeposition of carrier-free 57 Co on a rhodium matrix as the first step of preparing Moessbauer sources was studied. To optimize the plating parameters, the influences of current density, volume and pH of the electrolyte solution, shape, thickness, and surface area of the rhodium cathode, mode of cathode pretreatment, concentration of 57 Co and duration of electrolysis were investigated.

Ionic Liquids as Solvents for Rhodium and Platinum Catalysts Used in Hydrosilylation Reaction

Directory of Open Access Journals (Sweden)

Witold Zielinski

2016-08-01

Full Text Available A group of imidazolium and pyridinium based ionic liquids has been synthetized, and their ability to dissolve and activate the catalysts used in hydrosilylation reaction of 1-octane and 1,1,1,3,5,5,5-heptamethyltrisiloxane was investigated. An organometallic catalyst as well as inorganic complexes of platinum and rhodium dissolved in ionic liquids were used, forming liquid solutions not miscible with the substrates or with the products of the reaction. The results show that application of such a simple biphasic catalytic system enables reuse of ionic liquid phase with catalysts in multiple reaction cycles reducing the costs and decreasing the amount of catalyst needed per mole of product.

Zeolitization at uranium ore manifestation

International Nuclear Information System (INIS)

Petrosyan, R.V.; Buntikova, A.F.

1981-01-01

The process of zeolitization at uranium ore manifestation is studied. A specific type of low-temperature wall endogenous alteration of rocks due to the effect of primary acid solution with low content of carbonic acid is established. Leaching of calcium from enclosing rocks and its deposition in ore-accompanying calcium zeolites is a characteristic feature of wall-metasomatosis. Formation of desmin- calcite-laumontite and quartz-fluoroapatite of vein associations, including ore minerals (uranophane and metaotenite), is genetically connected with calcium metasomatosis. On the basis of the connection of ore minerals with endogeneous process of zeolitization a conclusion can be made on endogenous origin of uranophane and metaotenite [ru

Excess Substrate is a Spectator Ligand in a Rhodium-Catalyzed Asymmetric [2+2+2] Cycloaddition of Alkenyl Isocyanates with Tolanes

Science.gov (United States)

Oinen, Mark Emil; Yu, Robert T.; Rovis, Tomislav

2009-01-01

Excess substrate has been identified as an unintended spectator ligand affecting enantioselectivity in the [2+2+2] cycloaddition of alkenyl isocyanates with tolanes. Replacement of excess substrate with an exogenous additive affords products with consistent and higher ee’s. The increase in enantioselectivity is the result of a change in composition of a proposed rhodium(III) intermediate on the catalytic cycle. The net result is a rational probe of a short-lived rhodium(III) intermediate, and gives insight that may have applications in many rhodium catalyzed reactions. PMID:19803471

Preferable adsorption of phosphate using lanthanum-incorporated porous zeolite: Characteristics and mechanism

Science.gov (United States)

He, Yinhai; Lin, Hai; Dong, Yingbo; Wang, Liang

2017-12-01

The adsorbent, where lanthanum oxide was incorporated onto porous zeolite (La-Z), of preferable adsorption towards phosphate was prepared by hydrothermal synthesis. Based on pH effect results, La-Z would effectively sequestrate phosphate over wider pH range of 3.0-7.0, alkaline conditions were unfavorable for phosphate. The adsorption of phosphate was not significantly influenced by ionic strength and by coexisting anions of chloride, nitrate and sulfate but bicarbonate showed slightly greater negative effects, indicating La-Z possessed highly selectivity to phosphate. Adsorption of phosphate could be well fitted by pseudo-second-order model and the process was mainly controlled by intra-particle diffusion. Equilibrium adsorption demonstrated that Langmuir model was more suitable than Freundlich model for description phosphate adsorption and the adsorption capacity was 17.2 mg P g-1, which exhibited 95% utilization of incorporated La. Over 95% phosphate was eliminated in real effluent treatment when the dose was 2 g L-1. The underlying mechanism for phosphate capture was probed with Zeta potential and X-ray photoelectron spectroscope analysis, and the formation of La-P inner-sphere complexation was testified to be the dominant pathway. All the results suggested that the porous zeolite-supported lanthanum oxide can serve as a promising adsorbent for phosphate removal in realistic application.

Natural zeolite reactivity towards ozone: the role of compensating cations.

Science.gov (United States)

Valdés, Héctor; Alejandro, Serguei; Zaror, Claudio A

2012-08-15

Among indoor pollutants, ozone is recognised to pose a threat to human health. Recently, low cost natural zeolites have been applied as alternative materials for ozone abatement. In this work, the effect of compensating cation content of natural zeolite on ozone removal is studied. A Chilean natural zeolite is used here as starting material. The amount of compensating cations in the zeolite framework was modified by ion exchange using an ammonium sulphate solution (0.1 mol L(-1)). Characterisation of natural and modified zeolites were performed by X-ray powder diffraction (XRD), nitrogen adsorption at 77K, elemental analysis, X-ray fluorescence (XRF), thermogravimetric analysis coupled with mass spectroscopy (TGA-MS), and temperature-programmed desorption of ammonia (NH(3)-TPD). Ozone adsorption and/or decomposition on natural and modified zeolites were studied by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS). Results show that the zeolite compensating cation content affects ozone interaction with zeolite active sites. Ammonium ion-exchange treatments followed by thermal out-gassing at 823 K, reduces ozone diffusion resistance inside the zeolite framework, increasing ozone abatement on zeolite surface active sites. Weak and strong Lewis acid sites of zeolite surface are identified here as the main active sites responsible of ozone removal. Copyright © 2012 Elsevier B.V. All rights reserved.