Separation profiles of Sr from irradiated Yttrium matrix using different eluants by ion-exchange chromatography

International Nuclear Information System (INIS)

Ashok Kumar, G.V.S.; Vithya, J.; Kumar, R.; VenkataSubramani, C.R.

2014-01-01

89 Sr (a pure β - emitter, T 1/2 = 50.5d) is used in palliative care of bone metastases and was produced using the 89 Y(n,p) 89 Sr reaction in Fast Breeder Test Reactor (FBTR), Kalpakkam. The irradiated yttria target was dissolved in nitric acid and bulk separation of yttrium carried out by solvent extraction using TBP-HNO 3 followed by ion exchange chromatography of the aqueous phase with nitric acid as an eluting agent to obtain the pure fraction of 89 Sr. This paper discusses about the feasibility of separation of 89 Sr with other eluting agents in ion exchange chromatography vis-a-vis nitric acid. As this nuclide is injected as the chloride, the purified fraction of Sr in nitric acid medium is finally converted into HCI medium which is the preferred medium of source for its final application. In order to simplify the conversion, HCI medium can be used directly in the purifying stage making the process faster and simpler. Hence the separation profile using HCI was obtained. In addition, the elution pattern using another reagent tri sodium tri meta phosphate (SMP) was also determined. Purification of 89 Sr fraction using the eluants HCI and SMP was established. However, the elution with SMP yielded the 89 Sr fraction in a small volume and shorter period i.e. ∼ 9 h in comparison with 15 h and 22 h in the case of HCI and HNO 3 medium respectively and also generated less liquid waste. This study established that SMP can be a more favoured elution agent for the purification of 89 Sr source during the chemical processing of the bulk irradiated yttria target material. However the direct separation of Sr using the Sr selective crown ether i.e.ditert.butyl dicyclohexano 18 Crown 6, is much preferred over this method which is in progress

Unactivated yttrium tantalate phosphor

International Nuclear Information System (INIS)

Reddy, V.B.; Cheung, H.K.

1992-01-01

This patent describes an unactivated yttrium tantalate phosphor having M prime monoclinic structure and containing one or more additives of Rb and Al in an amount of between about 0.001 to 0.1 moles per mole of yttrium tantalate to improve brightness under X-radiation. This patent also describes an unactivated yttrium tantalate phosphor having M prime monoclinic structure and containing additives of Sr in an amount of between 0.001 to 0.1 moles per mole of yttrium tantalate and one or more of Rb and Al in an amount of between 0.001 to 0.1 moles per mole of yttrium tantalate the phosphor exhibiting a greater brightness under X-radiation than the phosphor absent Rb and Al

Abscopal Effects and Yttrium-90 Radioembolization

Energy Technology Data Exchange (ETDEWEB)

Ghodadra, Anish; Bhatt, Sumantha [University Pittsburgh School of Medicine, Department of Radiology (United States); Camacho, Juan C. [Emory University School of Medicine, Department of Radiology and Imaging Sciences (United States); Kim, Hyun S., E-mail: kevin.kim@yale.edu [University Pittsburgh School of Medicine, Department of Radiology (United States)

2016-07-15

We present the case of an 80-year-old male with squamous cell carcinoma with bilobar hepatic metastases who underwent targeted Yttrium-90 radioembolization of the right hepatic lobe lesion. Subsequently, there was complete regression of the nontargeted, left hepatic lobe lesion. This may represent the first ever reported abscopal effect in radioembolization. The abscopal effect refers to the phenomenon of tumor response in nontargeted sites after targeted radiotherapy. In this article, we briefly review the immune-mediated mechanisms responsible for the abscopal effect.

Diffusion of hydrogen in yttrium

International Nuclear Information System (INIS)

Vorobyov, V.V.; Ryabchikov, L.N.

1966-01-01

In this work the diffusion coefficients of hydrogen in yttrium were determined from the rate at which the hydrogen was released from yttrium samples under a vacuum at temperatures of 450 to 850 0 C and from the quantity of hydrogen retained by yttrium at hydrogen pressures below 5 x 10 - 4 mm Hg in the same temperature range

90Sr- 90Y and 89Sr beta radioactivity measurement in milk samples using a proportional counter

International Nuclear Information System (INIS)

Mananes, A.; Perez Santos, C.; Martinez Churiaque, F.

1987-01-01

A thin window glas flow proportional counter is used to measure the 90 Sr- 90 Y and 89 Sr beta radioactivity in milk samples. A chemical procedure is used to separate strontium-yttrium from the other radionuclides present in milk. A calculation of the total efficiency of the system is performed which includes an empirical estimation of the backscattering factor. The calibration of the whole process allows the determination of the 90 Sr activity within 10% relative error in spite of uncertainties in the recovery yields of strontium and yttrium. No 89 Sr activity has been detected, and the mean value obtained for the 90 Sr activity in nine milk samples of Cantabria is 0.115 Bq/1 with a minimum detectable activity of 0.0105 Bq. (author) 18 refs

Texture and deformation mechanism of yttrium

International Nuclear Information System (INIS)

Adamesku, R.A.; Grebenkin, S.V.; Stepanenko, A.V.

1992-01-01

X-ray pole figure analysis was applied to study texture and deformation mechanism in pure and commercial polycrystalline yttrium on cold working. It was found that in cast yttrium the texture manifected itself weakly enough both for pure and commercial metal. Analysis of the data obtained made it possible to assert that cold deformation of pure yttrium in the initial stage occurred mainly by slip the role of which decreased at strains higher than 36%. The texture of heavily deformed commercial yttrium contained two components, these were an 'ideal' basic orientation and an axial one with the angle of inclination about 20 deg. Twinning mechanism was revealed to be also possible in commercial yttrium

Tattoo removal by Q-switched yttrium aluminium garnet laser

DEFF Research Database (Denmark)

Hutton Carlsen, K; Esmann, J; Serup, J

2017-01-01

BACKGROUND: Tattoo removal by Q-switched yttrium aluminium garnet (YAG) lasers is golden standard; however, clients' satisfaction with treatment is little known. OBJECTIVE: To determine clients' satisfaction with tattoo removal. METHODS: One hundred and fifty-four tattoo removal clients who had...... relative to colour of tattoo on a scale from 0 (no effect) to 10 (complete removal) scored a mean of blue 9.5, black 9.4, yellow 8.9, red 8.8 and green 6.5. Clients were dissatisfied with green pigment remnants, which could mimic bruising. One hundred and twenty-nine clients (84%) experienced moderate...

Kinetics of yttrium dissolution from waste ceramic dust

OpenAIRE

STOPIC SRECKO R.; FRIEDRIH BERND G.

2016-01-01

Yttrium is a silvery transition metal and has similar chemical properties to lanthanoids. Because of this similarity, yttrium belongs to rare earth elements. Ytttrium and yttrium oxide are mostly used in fluoroscent lamps, production of electrodes, in electronic filters, lasers, superconductors and as additives in various materials to improve their properties. Yttrium is mainly recovered from the minerals monazite [(Ce,La,Th,Nd,Y)PO4] and xenotime YPO4.The presence of radioactive elements suc...

Interaction of oxygen vacancies in yttrium germanates

KAUST Repository

Wang, Hao

2012-01-01

Forming a good Ge/dielectric interface is important to improve the electron mobility of a Ge metal oxide semiconductor field-effect transistor. A thin yttrium germanate capping layer can improve the properties of the Ge/GeO 2 system. We employ electronic structure calculations to investigate the effect of oxygen vacancies in yttrium-doped GeO 2 and the yttrium germanates Y 2Ge 2O 7 and Y 2GeO 5. The calculated densities of states indicate that dangling bonds from oxygen vacancies introduce in-gap states, but the system remains insulating. However, yttrium-doped GeO 2 becomes metallic under oxygen deficiency. Y-doped GeO 2, Y 2Ge 2O 7 and Y 2GeO 5 are calculated to be oxygen substoichiometric under low Fermi energy conditions. The use of yttrium germanates is proposed as a way to effectively passivate the Ge/dielectric interface. This journal is © 2012 the Owner Societies.

Scandium, yttrium and the lanthanides

International Nuclear Information System (INIS)

Hart, F.A.

1987-01-01

This chapter on the chemistry of the coordination complexes of scandium, yttrium and the lanthanides includes sections on the nitrogen and oxygen donor ligands and complex halides of scandium, and the phosphorus and sulfur donor ligands of yttrium and the lanthanides. Complexes with the macrocylic ligands and with halides are also discussed. Sections on the NMR and electronic spectra of the lanthanides are also included. (UK)

Features of solid solutions composition in magnesium with yttrium alloys

International Nuclear Information System (INIS)

Drits, M.E.; Rokhlin, L.L.; Tarytina, I.E.

1983-01-01

Additional data on features of yttrium solid solutions composition in magnesium in the course of their decomposition investigation in the case of aging are obtianed. The investigation has been carried out on the base of a binary magnesium-yttrium alloy the composition of which has been close to maximum solubility (at eutectic temperature) and magnesium-yttrium alloys additionally doped with zinc. It is shown that higher yttrium solubility in solid magnesium than it has been expected, issueing from the difference in atomic radii of these metals indicates electron yttrium-magnesium atoms interaction. In oversaturated magnesium-yttrium solid solutions at earlier decomposition stages Mg 3 Cd type ordering is observed. At aging temperatures up to 250 deg C and long exposures corresponding to highest strengthening in oversaturated magnesium yttrium solid solutions a rhombic crystal lattice phase with three symmetric orientations is formed

Extraction of nitrates of lanthanoids (3) of the yttrium group and yttrium (3) by trialkylbenzylammonium nitrate in toluene

International Nuclear Information System (INIS)

Pyartman, A.K.; Kovalev, S.V.; Keskinov, V.A.; Kopyrin, A.A.

1997-01-01

A study was made on extraction of nitrates of lanthanoids (3) of the yttrium group (terbium-lutetium) and yttrium (3) by trialkylbensylammonium nitrate in toluene at T=298.15 K pH 2. Extraction isotherms are described with account of formation of compound of (R 4 N) 2 [Ln(NO 3 ) 5 ] composition in organic phase. Values of extraction constants decreasing in terbium (3)-lutetium (3) series, were calculated. Value of extraction constant for yttrium (3) is close to the value of extraction constant for ytterbium (3). 13 refs., 2 figs., 3 tabs

On the use of hydrogen peroxide as a masking agent for the determination of yttrium in uranium oxide - yttrium oxide mixture

International Nuclear Information System (INIS)

Rastogi, R.K.; Chaudhuri, N.K.; Rizvi, G.H.; Subramanian, M.S.

1985-01-01

The use of peroxide as a masking agent for uranium during the EDTA titration of yttrium in an yttrium-uranium mixture containing large amounts of uranium was investigated. High acetate ion concentration was necessary to keep the peroxy complex of uranium in solution during the titration. It was observed that uranium could be tolerated up to 500 mg in the determination of yttrium with 0.5 ml of 30% hydrogen peroxide in approx. 1M acetate medium. The precision and accuracy of the method based on 16 determinations of yttrium at 6-16 mg level in the presence of 300 mg uranium was found to be +-0.2%. (author)

PET imaging of soluble yttrium-86-labeled carbon nanotubes in mice.

Directory of Open Access Journals (Sweden)

Michael R McDevitt

2007-09-01

Full Text Available The potential medical applications of nanomaterials are shaping the landscape of the nanobiotechnology field and driving it forward. A key factor in determining the suitability of these nanomaterials must be how they interface with biological systems. Single walled carbon nanotubes (CNT are being investigated as platforms for the delivery of biological, radiological, and chemical payloads to target tissues. CNT are mechanically robust graphene cylinders comprised of sp(2-bonded carbon atoms and possessing highly regular structures with defined periodicity. CNT exhibit unique mechanochemical properties that can be exploited for the development of novel drug delivery platforms. In order to evaluate the potential usefulness of this CNT scaffold, we undertook an imaging study to determine the tissue biodistribution and pharmacokinetics of prototypical DOTA-functionalized CNT labeled with yttrium-86 and indium-111 ((86Y-CNT and (111In-CNT, respectively in a mouse model.The (86Y-CNT construct was synthesized from amine-functionalized, water-soluble CNT by covalently attaching multiple copies of DOTA chelates and then radiolabeling with the positron-emitting metal-ion, yttrium-86. A gamma-emitting (111In-CNT construct was similarly prepared and purified. The constructs were characterized spectroscopically, microscopically, and chromatographically. The whole-body distribution and clearance of yttrium-86 was characterized at 3 and 24 hours post-injection using positron emission tomography (PET. The yttrium-86 cleared the blood within 3 hours and distributed predominantly to the kidneys, liver, spleen and bone. Although the activity that accumulated in the kidney cleared with time, the whole-body clearance was slow. Differential uptake in these target tissues was observed following intravenous or intraperitoneal injection.The whole-body PET images indicated that the major sites of accumulation of activity resulting from the administration of (86Y-CNT were

Analyses and quantitative determination of the strontium radioisotopes 89 and 90 in milk powder; Recherche et dosage des isotopes radioactifs 89 et 90 du strontium dans le lait en poudre

Energy Technology Data Exchange (ETDEWEB)

Jeanmaire, L; Michon, G [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

The authors describe a procedure for the determination of the strontium radioisotopes 89 and 90. The concentration of strontium is made possible by the insolubility of its nitrate salt in strong nitric acid which allows the removal of greatest part of calcium. The purification is performed on a cation exchange column. The amount of radioisotope 90 is determined by means of its daughter product yttrium 90 necessary calibrations and computations are treated in special paragraphs. With regard to the reproducibility of the measurements, the fluctuations are less than 20 per cent. This seems satisfaction for such a technique which have great sensibility while being long and necessitative great carefulness. (author) [French] Les auteurs decrivent une technique de dosage des isotopes 89 et 90 du strontium. La concentration du strontium est assuree grace a l'insolubilite de son nitrate dans l'acide nitrique concentre, ce qui permet d'eliminer la plus grande partie du Ca. La purification se fait sur une colonne echangeuse de cations. L'isotope 90 est dose grace a son descendant l'yttrium 90. Les etalonnages et calculs necessaires font l'objet de paragraphes detailles. En ce qui concerne la reproductibilite des mesures, les fluctuations sont inferieures a 20 pour cent, ce qui semble satisfaisant devant la grande sensibilite de la methode qui reste cependant longue et delicate. (auteur)

Glypican-3–Targeting F(ab′)2 for 89Zr PET of Hepatocellular Carcinoma

OpenAIRE

Sham, Jonathan G.; Kievit, Forrest M.; Grierson, John R.; Chiarelli, Peter A.; Miyaoka, Robert S.; Zhang, Miqin; Yeung, Raymond S.; Minoshima, Satoshi; Park, James O.

2014-01-01

Hepatocellular carcinoma (HCC) is an increasingly lethal malignancy for which management is critically dependent on accurate imaging. Glypican-3 (GPC3) is a cell surface receptor overexpressed in most HCCs and provides a unique target for molecular diagnostics. The use of monoclonal antibodies (mAbs) that target GPC3 (αGPC3) in PET imaging has shown promise but comes with inherent limitations associated with mAbs such as long circulation times. This study used 89Zr-conjugated F(ab′)2 fragment...

Uncertainty and Detection Limit in Determination of 89,90Sr by Cherenkov Counting

International Nuclear Information System (INIS)

Grahek, Z.; Karanovic, G.; Nodilo, M.

2013-01-01

The methodology for the rapid determination of 89,90Sr in normal and emergency situations is given. Methodology is based on simultaneous separation of strontium and yttrium from samples and quantitative 89,90Sr determination by Cherenkov counting within three days. Methodology for quantitative determination by Cherenkov counting based on following changes of sample activity during the time is described and discussed. It has been shown that 89,90Sr can be determined with acceptable accuracy when 89Sr/90Sr ratio is over 10:1. Obtained results show that by using low level liquid scintillation counter it can be possible to determine 89Sr and 90Sr in broad range of concentration activities (1 - 1000 Bq (kgL) -1 ) with uncertainties below 10% within 2-3 days. Results also show that accuracy of determination of 89Sr (and 90Sr) depends on determination of difference between separation and counting time when activity ratio of 89Sr/90Sr is high. Analysis of combined uncertainty shows that it mainly depends on uncertainty of efficiency and recovery determination, uncertainty of activities determination for both isotopes and level of background radiation. Portion of each in combined uncertainty depend on level of activity of each isotope and its activity ratio.(author)

Surface modifications induced by yttrium implantation on low manganese-carbon steel

Energy Technology Data Exchange (ETDEWEB)

Caudron, E.; Buscail, H. [Univ. Blaise Pascal Clermont-Fd II, Le Puy en Velay (France). Lab. Vellave d' Elaboration et d' Etude des Materiaux; Haanapel, V.A.C.; Jacob, Y.P.; Stroosnijder, M.F. [Institute for Health and Consumer Protection, Joint Research Center, The European Commission, 21020, Ispra (Italy)

1999-12-15

Low manganese-carbon steel samples were ion implanted with yttrium. Sample compositions and structures were investigated before and after yttrium implantations to determine the yttrium distribution in the sample. Yttrium implantation effects were characterized using several analytical and structural techniques such as X-ray photoelectron spectroscopy, reflection high energy electron diffraction, X-ray diffraction, glancing angle X-ray diffraction and Rutherford backscattering spectrometry. In this paper it is shown that correlation between composition and structural analyses provides an understanding of the main compounds induced by yttrium implantation in low manganese-carbon steel. (orig.)

Yttrium and rare earths separation by ion exchange resin

International Nuclear Information System (INIS)

Pinatti, D.G.; Ayres, M.J.G.; Ribeiro, S.; Silva, G.L.J.P.; Silva, M.L.C.P.; Martins, A.H.

1988-01-01

The experimental results of yttrium and rare earths separation from Brazilian xenotime are presented. The research consist in five stage: 1) Preparation of yttrium, erbium and lutetium standard solutions, from solubilization of pure oxides 2) yttrium and rare earths separation by ion exchange chromatrography 3) Separation and recovery of EDTA 4) Precipitation and calcination and 4) Analytical control of process. (C.G.C.) [pt

Effects of hepatic arterial yttrium 90 glass microspheres in dogs.

Science.gov (United States)

Wollner, I; Knutsen, C; Smith, P; Prieskorn, D; Chrisp, C; Andrews, J; Juni, J; Warber, S; Klevering, J; Crudup, J

1988-04-01

A 22-micron glass microsphere called TheraSphere (Theragenics Corp., Atlanta, GA) has been developed in which yttrium 89 oxide is incorporated into the glass matrix and is activated by neutron bombardment to form the beta-emitting isotope yttrium 90 (Y 90) before using the spheres as radiotherapeutic vehicles. The injection of up to 12 times (on a liver weight basis) the anticipated human dose of nonradioactive TheraSphere into the hepatic arteries of dogs was well tolerated and produced clinically silent alterations within centrolobular areas. The hepatic arterial (HA) injection of radioactive TheraSphere also produced portal changes similar to those observed in humans after external beam therapy. While the extent of damage increased with the delivered dose, radiation exposures in excess of 30,000 cGy did not cause total hepatic necrosis and were compatible with survival. No microspheres distributed to the bone marrow and absolutely no myelosuppression was encountered in any animal. Proposed hepatic exposures to humans of 5000 to 10,000 cGy by means of these microspheres, therefore, would appear to be feasible and tolerable. Radiotherapeutic microsphere administration preceded by regional infusion of a radiosensitizing agent and/or immediately following the redistribution of blood flow toward intrahepatic tumor by vasoactive agents can potentially yield a synergistic, highly selective attack on tumors confined to the liver.

Solubility and peculiarities of the yttrium-aluminium borate crystal growth

International Nuclear Information System (INIS)

Azizov, A.V.; Leonyuk, N.I.; Rezvyj, V.R.; Timchenko, T.I.; Belov, N.V.

1982-01-01

The nature of crystallization media and crystallization peculiarities of IAl 3 [BO 3 ] 4 yttrium-alluminium borate (YAB) were investigated. The investigation of YAB solubility was conducted in the melts of two different compositions: 88.1K 2 Mo 2 O 10 -3.5V 2 O 3 -8.4B 2 O 3 (1) and 89.5K 2 Mo 3 O 10 - - 10.5B 2 O 3 (2) at 1060-900 deg C. The YAB crystals obtained from different crystallization media had different habit and morphology. The revealed peculiarities are significant for the choice of the YAB crystal growing conditions on orientated seedings: more rapid growth can be exercised along the [0001] face from the solution in the melt (2)

Method for chromatographically recovering scandium and yttrium

International Nuclear Information System (INIS)

Snyder, T.S.; Stoltz, R.A.

1991-01-01

This paper describes a method for chromatographically recovering scandium and yttrium from the residue of a sand chlorinator. It comprises: providing a residue from a sand chlorinator, the residue containing scandium, yttrium, sodium, calcium and at least one radioactive metal of the group consisting of radium, thorium and uranium; digesting the residue with an acid to produce an aqueous liquid containing scandium, yttrium, sodium, calcium and at least one radioactive metal of the group consisting of radium, thorium and uranium; feeding the metal containing liquid through a cation exchanger; eluding the cation exchanger with an acid eluant to to produce: a first eluate containing at least half of the total weight of the calcium and sodium in the feed liquid; a second eluate containing at least half of the total weight of the one or more radioactive metals in the feed liquid; a third eluate containing at least half of the yttrium in the feed liquid, and a fourth eluate containing at least half of the weight of the scandium in the feed liquid

Reaction of yttrium polonides with carbon dioxide

International Nuclear Information System (INIS)

Abakumov, A.S.; Khokhlov, A.D.; Reznikova, N.F.

1986-01-01

It has been proved that heating of yttrium and tantalum in carbon dioxide to 500 and 800 0 C alters the gas phase composition, causing formation of carbon monoxide and reduction of oxygen content. A study of the thermal stability of yttrium polonides in carbon dioxide showed that yttrium sesqui- and monopolonides decompose at 400-430 0 C. The temperature dependence of the vapor pressure of polonium obtained upon decomposition of the referred polonides has been determined in a carbon dioxide environment radiotensometrically. The enthalpy of the process calculated from this dependence is close to the enthalpy of vaporization of elemental polonium in vacuo. The mechanism of the reactions has been suggested

Yttrium implantation effects on extra low carbon steel and pure iron

Energy Technology Data Exchange (ETDEWEB)

Caudron, E.; Buscail, H. [Clermont-Ferrand-2 Univ., Le Puy en Velay (France). Lab. Vellave d`Elaboration; Jacob, Y.P.; Stroosnijder, M.F. [Institute for Advanced Materials, Joint Research Center, The European Commission, 21020, Ispra (Vatican City State, Holy See) (Italy); Josse-Courty, C. [Laboratoire de Recherche sur la Reactivite des Solides, UMR 56-13 CNRS, UFR Sciences et Techniques, 9 Avenue A. Savary, B.P. 400, 21011, Dijon Cedex (France)

1999-05-25

Extra low carbon steel and pure electrolytic iron samples were yttrium implanted using ion implantation technique. Compositions and structures of pure iron and steel samples were investigated before and after yttrium implantation by several analytical and structural techniques (RBS, SIMS, RHEED and XRD) to observe the yttrium implantation depth profiles in the samples. This paper shows the different effects of yttrium implantations (compositions and structures) according to the implanted sample nature. (orig.) 23 refs.

Importance Role of Low-Cost Sorbent Produced from rice husk in Separation of zirconium from yttrium

International Nuclear Information System (INIS)

Kandil, S.A.

2013-01-01

The agricultural waste, rice husk, was used as a precursor for the production of low-cost sorbent. Rice husk, a by-product of the rice milling industry, accounts for about 20 % of the whole rice. The argro-residue sorbent extracted from rice husk was employed in separation of zirconium from yttrium. The separation of Zr from the binary systems (Zr-Y) was achieved in batch and column modes. In a batch mode, the adsorption behavior was studied in deferent media, namely, hydrochloric acid, 0.1 M citrate buffer and 0.1 M acetate buffer. In addition, other factors affecting the sorption process of each metal e.g. ph-value of the medium and metal ion concentration were also studied. The breakthrough experiments were carried in the form of mini-column with different bed depths of sorbent at flow rates of 20 ml/min and 40 ml/min. These studies were performed to elucidate the valuable of use of locally, available, agro-residue for separation of Zr from Y target as a promising sorbent for purification of 88 Zr, 89 Zr from Y.

N-m-nitrocinnamoylphenylhydroxyl-amine as reagent for amperometric determination of yttrium

International Nuclear Information System (INIS)

Oliferenko, G.L.; Gallaj, Z.A.; Sheina, N.M.; Shvedene, N.V.

1983-01-01

Possibility of using organic reagent of unsaturated N-arylsubstituted derivatives class of hydroxamic acids N-m-nitrocinnamoyl phenylhydroxylamire (NCPHA) for amperometric titration of yttrium using indication of e.t.p. by current of reagent oxidation on graphite electrode is investigated. Metal and the NCPHA form difficultly soluble complex with ratio of yttrium to the NCPHA, which is equal to 1:3. Buffer mixtures of 0.1MNH 3 +0.1MCH 3 COOH composis tion with pH 6.3-7.5 are optimal background solutions for amperometric titration of yttrium. The proposed method permits to determine 10-600 μkg of yttrium in the volume of 10 ml. Effect of the series of strange elements on titration of yttrium with NCPHA (Ca, Mg, Mn (2), Al, CU (2), Fe (3) REE and others) is studied. The developed method is used for yttrium determination in luminophores of Casub(n)-- Ysub(m)Fsub(z)xMn(2) (1-10%) composition

Treatment of exhaust fluorescent lamps to recover yttrium: Experimental and process analyses

International Nuclear Information System (INIS)

De Michelis, Ida; Ferella, Francesco; Varelli, Ennio Fioravante; Veglio, Francesco

2011-01-01

Highlights: → Recovery of yttrium from spent fluorescent lamps by sulphuric acid leaching. → The use of sulphuric acid allows to reduce calcium dissolutions. → Main contaminant of fluorescent powder are Si, Pb, Ca and Ba. → Hydrated yttrium oxalate, recovered by selective precipitation, is quite pure (>90%). → We have studied the whole process for the treatment of dangerous waste (plant capability). - Abstract: The paper deals with recovery of yttrium from fluorescent powder coming from dismantling of spent fluorescent tubes. Metals are leached by using different acids (nitric, hydrochloric and sulphuric) and ammonia in different leaching tests. These tests show that ammonia is not suitable to recover yttrium, whereas HNO 3 produces toxic vapours. A full factorial design is carried out with HCl and H 2 SO 4 to evaluate the influence of operating factors. HCl and H 2 SO 4 leaching systems give similar results in terms of yttrium extraction yield, but the last one allows to reduce calcium extraction with subsequent advantage during recovery of yttrium compounds in the downstream. The greatest extraction of yttrium is obtained by 20% w/v S/L ratio, 4 N H 2 SO 4 concentration and 90 deg. C. Yttrium and calcium yields are nearly 85% and 5%, respectively. The analysis of variance shows that acid concentration alone and interaction between acid and pulp density have a significant positive effect on yttrium solubilization for both HCl and H 2 SO 4 medium. Two models are empirically developed to estimate yttrium and calcium concentration during leaching. Precipitation tests demonstrate that at least the stoichiometric amount of oxalic acid is necessary to recover yttrium efficiently and a pure yttrium oxalate n-hydrate can be produced (99% grade). The process is economically feasible if other components of the fluorescent lamps (glass, ferrous and non-ferrous scraps) are recovered after the equipment dismantling and valorized, besides the cost that is usually paid

Crystallization of Yttrium and Samarium Aluminosilicate Glasses

OpenAIRE

Lago, Diana Carolina; Prado, Miguel Oscar

2016-01-01

Aluminosilicate glasses containing samarium and yttrium (SmAS and YAS glasses) exhibit high glass transition temperatures, corrosion resistance, and glass stability on heating which make them useful for technological applications. Yttrium aluminosilicate glass microspheres are currently being used for internal selective radiotherapy of liver cancer. During the preparation process, crystallization needs to be totally or partially avoided depending on the final application. Thus knowing the cry...

Yttrium doped BSCF membranes for oxygen separation

DEFF Research Database (Denmark)

Haworth, P.; Smart, S.; Glasscock, Julie

2011-01-01

This work investigates the partial substitution of yttrium in place of iron in BSCF to form Ba0.5Sr0.5Co0.8Fe0.2−xYxO3−δ, where x varied between 0 and 0.2. X-ray diffraction patterns showed the formation of a perovskite cubic phase structure up to x = 0.15, whilst the full substitution of yttrium...

Yttrium and lanthanum recovery from low cerium carbonate, yttrium carbonate and yttrium concentrate; Aproveitamento de itrio e lantanio de um carbonato de terras raras de baixo teor em cerio, de um carbonato de itrio e de um oxido de terras itricas

Energy Technology Data Exchange (ETDEWEB)

Vasconcelos, Mari Estela de

2006-07-01

In this work, separation, enrichment and purification of lanthanum and yttrium were performed using as raw material a commercial low cerium rare earth concentrate named LCC (low cerium carbonate), an yttrium concentrate named 'yttrium carbonate', and a third concentrated known as 'yttrium earths oxide. The first two were industrially produced by the late NUCLEMON - NUCLEBRAS de Monazita e Associados Ltda, using Brazilian monazite. The 'yttrium earths oxide' come from a process for preparation of lanthanum during the course of the experimental work for the present thesis. The following techniques were used: fractional precipitation with urea; fractional leaching of the LCC using ammonium carbonate; precipitation of rare earth peroxycarbonates starting from the rare earth complex carbonates. Once prepared the enriched rare earth fractions the same were refined using the ion exchange chromatography with strong cationic resin without the use of retention ion and elution using the ammonium salt of ethylenediaminetetraacetic acid. With the association of the above mentioned techniques were obtained pure oxides of yttrium (>97,7%), lanthanum (99,9%), gadolinium (96,6%) and samarium (99,9%). The process here developed has technical and economic viability for the installation of a large scale unity. (author)

Thermoanalytical study of the formation mechanism of yttria from yttrium acetate

International Nuclear Information System (INIS)

Farjas, J.; Camps, J.; Roura, P.; Ricart, S.; Puig, T.; Obradors, X.

2011-01-01

Highlights: → Thermal decomposition of yttrium acetate: three endothermic stages. → Intermediates: yttrium hydroxide and carbonate. → Product: cubic yttria (the degree of transformation is at least 99%). → The decomposition does not depend on the oxygen partial pressure. - Abstract: The processes involved in the thermal decomposition of yttrium acetate tetrahydrate, Y(CH 3 COO) 3 .4H 2 O, in air and in an inert atmosphere have been analyzed by thermoanalytical techniques (thermogravimetry, differential thermal analysis and evolved gas analysis) and by the structural characterization (X-ray diffraction, infrared spectroscopy, elemental analysis and scanning electron microscopy) of intermediates and final products. Decomposition of yttrium acetate is an endothermic transformation that takes place in a temperature range between 350 and 900 o C. The evolution of the mass during the decomposition process is not affected by the presence of oxygen. The process is initiated by the rupture of the bond between the metallic cation and the acetate ligand. This initial step (350-450 o C) involves the formation of amorphous yttrium hydroxide and yttrium carbonate and is characterized by a fast mass loss rate. A sudden decrease of the mass loss rate indicates a change in the decomposition kinetics that continues with the decomposition of yttrium hydroxide and yttrium carbonate. The main effect of an oxygen atmosphere is an intense exothermic process due to the combustion of organic species in the gas phase.

Studies on yttrium oxide coatings for corrosion protection against molten uranium

International Nuclear Information System (INIS)

Chakravarthy, Y.; Bhandari, Subhankar; Pragatheeswaran; Thiyagarajan, T.K.; Ananthapadmanabhan, P.V.; Das, A.K.; Kumar, Jay; Kutty, T.R.G.

2012-01-01

Yttrium oxide is resistant to corrosion by molten uranium and its alloys. Yttrium oxide is recommended as a protective oxide layer on graphite and metal components used for melting and processing uranium and its alloys. This paper presents studies on the efficacy of plasma sprayed yttrium oxide coatings for barrier applications against molten uranium

Improved production and processing of ⁸⁹Zr using a solution target.

Science.gov (United States)

Pandey, Mukesh K; Bansal, Aditya; Engelbrecht, Hendrik P; Byrne, John F; Packard, Alan B; DeGrado, Timothy R

2016-01-01

The objectives of the present work were to improve the cyclotron production yield of (89)Zr using a solution target, develop a practical synthesis of the hydroxamate resin used to process the target, and develop a biocompatible medium for (89)Zr elution from the hydroxamate resin. A new solution target (BMLT-2) with enhanced heat dissipation capabilities was designed by using helium-cooled dual foils (0.2 mm Al and 25 μ Havar) and an enhanced water-cooled, elongated solution cavity in the target insert. Irradiations were performed with 14 MeV protons on a 2M solution of yttrium nitrate in 1.25 M nitric acid at 40-μA beam current for 2 h in a closed system. Zirconium-89 was separated from Y by use of a hydroxamate resin. A one-pot synthesis of hydroxamate resin was accomplished by activating the carboxylate groups on a carboxymethyl cation exchange resin using methyl chloroformate followed by reaction with hydroxylamine hydrochloride. After trapping of (89)Zr on hydroxamate resin and rinsing the resin with HCl and water to release Y, (89)Zr was eluted with 1.2 M K2HPO4/KH2PO4 buffer (pH3.5). ICP-MS was used to measure metal contaminants in the final (89)Zr solution. The BMLT-2 target produced 349±49 MBq (9.4±1.2 mCi) of (89)Zr at the end of irradiation with a specific activity of 1.18±0.79 GBq/μg. The hydroxamate resin prepared using the new synthesis method showed a trapping efficiency of 93% with a 75 mg resin bed and 96-97% with a 100-120 mg resin bed. The elution efficiency of (89)Zr with 1.2M K2HPO4/KH2PO4 solution was found to be 91.7±3.7%, compared to >95% for 1 M oxalic acid. Elution with phosphate buffer gave very small levels of metal contaminants: Al=0.40-0.86 μg (n=2), Fe=1.22±0.71 μg (n=3), Y=0.29 μg (n=1). The BMLT-2 target allowed doubling of the beam current for production of (89)Zr, resulting in a greater than 2-fold increase in production yield in comparison with a conventional liquid target. The new one-pot synthesis of hydroxamate

Scattering of polarized protons by yttrium, iron and nickel nuclei

International Nuclear Information System (INIS)

Melssen, J.P.M.G.

1978-01-01

Results are presented of scattering experiments performed on yttrium and some iron and nickel isotopes with polarized proton beams at energies around 20 MeV. The angular distributions of the differential cross sections and analyzing powers have been measured and comparison of these with predictions from theoretical models has led to information about excited nuclear states like spin, parity and details of the wavefunctions. The DWBA has been mostly used to describe the reaction at the bombarding energies and for the target nuclei investigated. (C.F.)

Thermal decomposition of yttrium(III) propionate and butyrate

DEFF Research Database (Denmark)

Grivel, Jean-Claude

2013-01-01

The thermal decompositions of yttrium(III) propionate monohydrate (Y(C2H5CO2)3·H2O) and yttrium(III) butyrate dihydrate (Y(C3H7CO2)3·2H2O) were studied in argon by means of thermogravimetry, differential thermal analysis, IR-spectroscopy, X-ray diffraction and hot-stage microscopy. These two...

Solvent extraction studies on separation of yttrium from xenotime

International Nuclear Information System (INIS)

Singh, D.K.; Anitha, M.; Kain, V.

2017-01-01

Rare earths consists a group of 15 element from La to Lu in the periodic table and it also includes Sc and Y since they tend to occur in the same ore deposits as the lanthanides and exhibit similar chemical properties. The unique physical-chemical properties of the REEs render them important in applications as varies as high strength magnets, lighting phosphors, policing compounds and ceramics. In particular, yttrium finds numerous applications in many areas including superconductors, lasers, phosphors, nuclear reactors, astronavigation, ceramics etc. Yttrium is chemically similar to heavy rare earths (HRE: terbium, dysprosium, erbium, holmium, ytterbium, thulium and lutecium). Yttrium behaves like HRE due to similarity in ionic radius and finds place between Ho and Er. The cross current profile in terms of the plot of concentration of yttrium in raffinate as a function of contact number indicated the complete recovery of rare earths from nitrate solution of xenotime wet cake

Yttrium-90 used to treat colon cancer: Awaiting investigational new drug approval

International Nuclear Information System (INIS)

Anon.

1991-01-01

A new radiation treatment takes just 14 to 21 days to shrink colorectal tumors in laboratory mice, is under review for clinical trials with human cancer patients. The treatment has succeeded in reducing the size of tumors by up to 95%. Colon cancer, the second leading cause of cancer deaths in the US, is extremely difficult to treat unless it is detected early enough for surgical procedures. In laboratory tests over the last 5 years, a team of researchers has developed the treatment using yttrium-90. The yttrium-90 is transported to the tumors by attaching it to monoclonal antibodies that seek out the cancer cells. Once the radioisotope has been targeted to the tumor, the radiation destroys many of the cells, dramatically reducing the size of the tumor. Since this treatment usually does not completely eliminate all the cancer cells, it cannot be called a cure, but it does seem to be an effective method of shrinking colorectal tumors

A thermal neutron scattering law for yttrium hydride

Science.gov (United States)

Zerkle, Michael; Holmes, Jesse

2017-09-01

Yttrium hydride (YH2) is of interest as a high temperature moderator material because of its superior ability to retain hydrogen at elevated temperatures. Thermal neutron scattering laws for hydrogen bound in yttrium hydride (H-YH2) and yttrium bound in yttrium hydride (Y-YH2) prepared using the ab initio approach are presented. Density functional theory, incorporating the generalized gradient approximation (GGA) for the exchange-correlation energy, is used to simulate the face-centered cubic structure of YH2 and calculate the interatomic Hellmann-Feynman forces for a 2 × 2 × 2 supercell containing 96 atoms. Lattice dynamics calculations using PHONON are then used to determine the phonon dispersion relations and density of states. The calculated phonon density of states for H and Y in YH2 are used to prepare H-YH2 and Y-YH2 thermal scattering laws using the LEAPR module of NJOY2012. Analysis of the resulting integral and differential scattering cross sections demonstrates adequate resolution of the S(α,β) function. Comparison of experimental lattice constant, heat capacity, inelastic neutron scattering spectra and total scattering cross section measurements to calculated values are used to validate the thermal scattering laws.

Size-dependent cytotoxicity of yttrium oxide nanoparticles on primary osteoblasts in vitro

Energy Technology Data Exchange (ETDEWEB)

Zhou, Guoqiang, E-mail: zhougq1982@163.com; Li, Yunfei; Ma, Yanyan; Liu, Zhu; Cao, Lili; Wang, Da; Liu, Sudan; Xu, Wenshi; Wang, Wenying [Hebei University, Key Laboratory of Medicinal Chemistry and Molecular Diagnosis of Ministry of Education, Key Laboratory of Chemical Biology of Hebei Province, College of Chemistry and Environmental Science (China)

2016-05-15

Yttrium oxide nanoparticles are an excellent host material for the rare earth metals and have high luminescence efficiency providing a potential application in photodynamic therapy and biological imaging. In this study, the effects of yttrium oxide nanoparticles with four different sizes were investigated using primary osteoblasts in vitro. The results demonstrated that the cytotoxicity generated by yttrium oxide nanoparticles depended on the particle size, and smaller particles possessed higher toxicological effects. For the purpose to elucidate the relationship between reactive oxygen species generation and cell damage, cytomembrane integrity, intracellular reactive oxygen species level, mitochondrial membrane potential, cell apoptosis rate, and activity of caspase-3 in cells were then measured. Increased reactive oxygen species level was also observed in a size-dependent way. Thus, our data demonstrated that exposure to yttrium oxide nanoparticles resulted in a size-dependent cytotoxicity in cultured primary osteoblasts, and reactive oxygen species generation should be one possible damage pathway for the toxicological effects produced by yttrium oxide particles. The results may provide useful information for more rational applications of yttrium oxide nanoparticles in the future.

Development of 2024 AA-Yttrium composites by Spark Plasma Sintering

Science.gov (United States)

Vidyasagar, CH S.; Karunakar, D. B.

2018-04-01

The method of fabrication of MMNCs is quite a challenge, which includes advanced processing techniques like Spark Plasma Sintering (SPS), etc. The objective of the present work is to fabricate aluminium based MMNCs with the addition of small amounts of yttrium using Spark Plasma Sintering and to evaluate their mechanical and microstructure properties. Samples of 2024 AA with yttrium ranging from 0.1% to 0.5 wt% are fabricated by Spark Plasma Sintering (SPS). Hardness of the samples is determined using Vickers hardness testing machine. The metallurgical characterization of the samples is evaluated by Optical Microscopy (OM), Field Emission Scanning Electron Microscopy (FE-SEM). Unreinforced 2024 AA sample is also fabricated as a benchmark to compare its properties with those of the composite developed. It is found that the yttrium addition increases the above mentioned properties by altering the precipitation kinetics and intermetallic formation to some extent and then decreases gradually when yttrium wt% increases beyond 0.3 wt%. High density (˂ 99.75) is achieved in the samples and highest hardness achieved is 114 Hv, fabricated by spark plasma sintering and uniform distribution of yttrium is observed.

Sol gel synthesis for preparation of yttrium aluminium garnet

NARCIS (Netherlands)

Vrolijk, J.W.G.A.; Willems, J.W.M.M.; Metselaar, R.; With, de G.; Terpstra, R.A.; Metselaar, R.

1989-01-01

Sol-gel—synthesis for preparation of pure yttrium aluminium garnet powder with small grain size is subject of this ongoing study. Starting materials were sulfates and chlorides of yttrium and aluminium. To obtain pure YAG (Y3A1SO1Z) pH during hydrolysis as well as temperature during calcination and

Rapid determination of strontium-89 and strontium-90 in food and environmental samples by Cerenkov counting

International Nuclear Information System (INIS)

Melin, Judith; Suomela, Jorma

1995-01-01

The method has been developed for emergency situations. Minimum detectable concentrations of 5 Bq/liter, kilogram of strontium-89 and strontium-90 respectively is achievable in the presence of nuclides considered to be released under accidental conditions. Result on the strontium-89 and strontium-90 content in a sample can be obtained within 12 hours. One technician can easily handle 8-10 samples during a working day of eight hours. The determination of the strontium isotopes is accomplished by monitoring the Cerenkov radiation from strontium-89 and yttrium-90 in a liquid scintillation counter. The latter is the daughter product of strontium-90. Prior to the Cerenkov counting the sample is separated from interfering nuclides by oxalate precipitation, chromate precipitation and HDEHP-extraction. The method has to be further improved and evaluated with respect to different soil types such as forest mineral soil layers, agricultural soils and pastures. Furthermore, the decontamination procedure should be evaluated for a sample containing freshly irradiated uranium. (author)

Monocyte CD64 or CD89 targeting by surfactant protein D/anti-Fc receptor mediates bacterial uptake.

NARCIS (Netherlands)

Tacken, P.J.; Batenburg, J.J.

2006-01-01

We recently showed that a chimeric protein, consisting of a recombinant fragment of human surfactant protein D (rfSP-D) coupled to a Fab' fragment directed against the human Fcalpha receptor (CD89), effectively targets pathogens recognized by SP-D to human neutrophils. The present study evaluates

{alpha}-particle induced reactions on yttrium and terbium

Energy Technology Data Exchange (ETDEWEB)

Mukherjee, S.; Kumar, B.B. [School of Studies in Physics, Vikram University, Ujjain-456010 (India); Rashid, M.H. [Variable Energy Cyclotron Center, 1/AF, Bidhan Nagar, Calcutta (India); Chintalapudi, S.N. [Inter-University Consortium for DAE Facilities, 3/LB, Bidhan Nagar, Calcutta (India)

1997-05-01

The stacked foil activation technique has been employed for the investigation of {alpha}-particle induced reactions on the target elements yttrium and terbium up to 50 MeV. Six excitation functions for the ({alpha},xn) type of reactions were studied using high-resolution HPGe {gamma}-ray spectroscopy. A comparison with Blann{close_quote}s geometric dependent hybrid model has been made using the initial exciton number n{sub 0}=4(4p0h) and n{sub 0}=5(5p0h). A broad general agreement is observed between the experimental results and theoretical predictions with an initial exciton number n{sub 0}=4(4p0h). {copyright} {ital 1997} {ital The American Physical Society}

α-particle induced reactions on yttrium and terbium

International Nuclear Information System (INIS)

Mukherjee, S.; Kumar, B.B.; Rashid, M.H.; Chintalapudi, S.N.

1997-01-01

The stacked foil activation technique has been employed for the investigation of α-particle induced reactions on the target elements yttrium and terbium up to 50 MeV. Six excitation functions for the (α,xn) type of reactions were studied using high-resolution HPGe γ-ray spectroscopy. A comparison with Blann close-quote s geometric dependent hybrid model has been made using the initial exciton number n 0 =4(4p0h) and n 0 =5(5p0h). A broad general agreement is observed between the experimental results and theoretical predictions with an initial exciton number n 0 =4(4p0h). copyright 1997 The American Physical Society

Thermoanalytical study of the decomposition of yttrium trifluoroacetate thin films

International Nuclear Information System (INIS)

Eloussifi, H.; Farjas, J.; Roura, P.; Ricart, S.; Puig, T.; Obradors, X.; Dammak, M.

2013-01-01

We present the use of the thermal analysis techniques to study yttrium trifluoroacetate thin films decomposition. In situ analysis was done by means of thermogravimetry, differential thermal analysis, and evolved gas analysis. Solid residues at different stages and the final product have been characterized by X-ray diffraction and scanning electron microscopy. The thermal decomposition of yttrium trifluoroacetate thin films results in the formation of yttria and presents the same succession of intermediates than powder's decomposition, however, yttria and all intermediates but YF 3 appear at significantly lower temperatures. We also observe a dependence on the water partial pressure that was not observed in the decomposition of yttrium trifluoroacetate powders. Finally, a dependence on the substrate chemical composition is discerned. - Highlights: • Thermal decomposition of yttrium trifluoroacetate films. • Very different behavior of films with respect to powders. • Decomposition is enhanced in films. • Application of thermal analysis to chemical solution deposition synthesis of films

Spectrophotometric determination of yttrium with 2-(2-thiazolylazo)-5-dimethylaminophenol

International Nuclear Information System (INIS)

Tsurumi, Chikao; Furuya, Keiichi.

1975-01-01

Spectrophotometric determination of small amounts of yttrium with 2-(2-thiazolylazo)-5-dimethylaminophenol (TAM) in the presence of zephiramine was investigated. The recommended procedures were as follows; 2.0 ml of water, 7.0 ml of TAM-methanolic solution (2x10 -4 mol/l) and 2.0 ml of zephiramine-aqueous solution (1x10 -2 mol/l) were added to a solution containing less than 35 μg of yttrium and its pH was adjusted to 8.0 with 0.1 mol/l ammonium chloride-0.1 mol/l ammonium hydroxide solution. The solution was transferred to a 25 ml volumetric flask and diluted to the mark with water. After 20 minutes, the absorbance at 575 nm against a reagent blank was measured. The color of yttrium-TAM complex is reddish-violet in the presence of zephiramine and is stable for 90 minutes after color development. The yttrium-TAM complex shows an absorption maximum at 575 nm. The absorbance at 575 nm is constant in a pH range from 7.5 to 8.3. The molar extinction coefficient at this wavelength is 7.2x10 4 l.mol -1 .cm -1 . The band obeys Beer's law up to the concentration of 1.4 μg/ml of yttrium. The molar ratio of yttrium to TAM in the complex is 1 : 2. A number of ions interfere with the determination can be masked by the addition of various masking agents and removed in terms of trioctylamine-xylene extraction. Manganese, tantalum, tin(II), citrate and tartrate ions interfere with the determination. (auth.)

Evidence of yttrium silicate inclusions in YSZ-porcelain veneers.

Science.gov (United States)

Stoner, Brian R; Griggs, Jason A; Neidigh, John; Piascik, Jeffrey R

2014-04-01

This report introduces the discovery of crystalline defects that can form in the porcelain veneering layer when in contact with yttria-stabilized zirconia (YSZ). The focus was on dental prostheses and understanding the defects that form in the YSZ/porcelain system; however the data reported herein may have broader implications toward the use and stability of YSZ-based ceramics in general. Specimens were cut from fully sintered YSZ plates and veneering porcelain was applied (X-ray (EDAX) was used for microstructural and elemental analysis. EDAX, for chemical analysis and transmission electron diffraction (TED) for structural analysis were both performed in the transmission electron microscope (TEM). Additionally, in order to spatially resolve Y-rich precipitates, micro-CT scans were conducted at varying depths within the porcelain veneer. Local EDAX (SEM) was performed in the regions of visible inclusions and showed significant increases in yttrium concentration. TEM specimens also showed apparent inclusions in the porcelain and selected area electron diffraction was performed on these regions and found the inclusions to be crystalline and identified as either yttrium-silicate (Y2 SiO5 ) or yttrium-disilicate (Y2 Si2 O7 ). Micro-CT data showed that yttrium-silicate precipitates were distributed throughout the thickness of the porcelain veneer. Future studies are needed to determine whether many of the premature failures associated with this materials system may be the result of crystalline flaws that form as a result of high temperature yttrium diffusion near the surfaces of YSZ. © 2013 Wiley Periodicals, Inc.

Attempts at treating rheumatoid arthritis with radioactive yttrium

International Nuclear Information System (INIS)

Scott, J.T.

1979-01-01

Two years' observations on 33 knee joints in 33 patients with rheumatoid arthritis did not prove a therapeutic effect of Y 90 , which was tested in a randomized study against non-radioactive yttrium. It was noticable that 9 knee joints of the isotope group but only one of the control group became unstable. Independent of the yttrium treatment, significant improvement was noticed in patients where fibrin clots had been washed out of the joints in the course of arthroscopies. (orig.) [de

Process for recovering yttrium and lanthanides from wet-process phosphoric acid

Energy Technology Data Exchange (ETDEWEB)

Janssen, J.A.; Weterings, C.A.

1983-06-28

Process for recovering yttrium and lanthanides from wet-process phosphoric acid by adding a flocculant to the phosphoric acid, separating out the resultant precipitate and then recovering yttrium and lanthanides from the precipitate. Uranium is recovered from the remaining phosphoric acid.

Yttrium-90 - ED 4310

International Nuclear Information System (INIS)

Ammerich, M.; Frot, P.; Gambini, D.; Gauron, C.; Moureaux, P.; Herbelet, G.; Lahaye, T.; Pihet, P.; Rannou, A.; Vidal, E.

2013-03-01

This sheet presents the characteristics of yttrium-90, its origin, and its radio-physical and biological properties. It briefly describes its use in nuclear medicine. It indicates its dosimetric parameters for external exposure, cutaneous contamination, and internal exposure due to acute contamination or to chronic contamination. It indicates and comments the various exposure control techniques: ambient dose rate measurement, surface contamination measurement, atmosphere contamination. It addresses the means of protection: premise design, protection against external exposure and against internal exposure. It describes how areas are delimited and controlled within the premises: regulatory areas, controls to be performed. It addresses the personnel classification, training and medical survey. It addresses the issue of solid and liquid wastes and liquid or gaseous effluents. It briefly recalls the administrative procedures related to the authorization and declaration of possession and use of sealed and unsealed sources. It indicates regulatory aspects related to the transport of yttrium-90, describes what is to be done in case of incident or accident (for the different types of contamination or exposure)

Photocatalysis of Yttrium Doped BaTiO3 Nanofibres Synthesized by Electrospinning

Directory of Open Access Journals (Sweden)

Zhenjiang Shen

2015-01-01

Full Text Available Yttrium doped barium titanate (BT nanofibres (NFs with significant photocatalytic effect were successfully synthesized by electrospinning. Considering the necessary factors for semiconductor photocatalysts, a well-designed procedure was carried out to produce yttrium doped BT (BYT NFs. In contrast to BYT ceramics powders and BT NFs, BYT NFs with pure perovskite phase showed much enhanced performance of photocatalysis. The surface modification in electrospinning and subsequent annealing, the surface spreading of transition metal yttrium, and the narrowed band gap energy in yttrium doping were all contributed to the final novel photocatalytic effect. This work provides a direct and efficient route to obtain doped NFs, which has a wide range of potential applications in areas based on complex compounds with specific surface and special doping effect.

The behaviour of selected yttrium containing bioactive glass microspheres in simulated body environments.

Science.gov (United States)

Cacaina, D; Ylänen, H; Simon, S; Hupa, M

2008-03-01

The study aims at the manufacture and investigation of biodegradable glass microspheres incorporated with yttrium potentially useful for radionuclide therapy of cancer. The glass microspheres in the SiO2-Na2O-P2O5-CaO-K2O-MgO system containing yttrium were prepared by conventional melting and flame spheroidization. The behaviour of the yttrium silicate glass microspheres was investigated under in vitro conditions using simulated body fluid (SBF) and Tris buffer solution (TBS), for different periods of time, according to half-life time of the Y-90. The local structure of the glasses and the effect of yttrium on the biodegradability process were evaluated by Fourier Transform Infrared (FT-IR) spectroscopy and Back Scattered Electron Imaging of Scanning Electron Microscopy (BEI-SEM) equipped with Energy Dispersive X-ray (EDX) analysis. UV-VIS spectrometry and Inductively Coupled Plasma Mass Spectrometry (ICP-MS) was used for analyzing the release behaviour of silica and yttrium in the two used solutions. The results indicate that the addition of yttrium to a bioactive glass increases its structural stability which therefore, induced a different behaviour of the glasses in simulated body environments.

Analyses and quantitative determination of the strontium radioisotopes 89 and 90 in milk powder

International Nuclear Information System (INIS)

Jeanmaire, L.; Michon, G.

1959-01-01

The authors describe a procedure for the determination of the strontium radioisotopes 89 and 90. The concentration of strontium is made possible by the insolubility of its nitrate salt in strong nitric acid which allows the removal of greatest part of calcium. The purification is performed on a cation exchange column. The amount of radioisotope 90 is determined by means of its daughter product yttrium 90 necessary calibrations and computations are treated in special paragraphs. With regard to the reproducibility of the measurements, the fluctuations are less than 20 per cent. This seems satisfaction for such a technique which have great sensibility while being long and necessitative great carefulness. (author) [fr

Yttrium aluminum garnet coating on glass substrate

Energy Technology Data Exchange (ETDEWEB)

Ferreira, Camila M.A.; Freiria, Gabriela S.; Faria, Emerson H. de; Rocha, Lucas A.; Ciuffi, Katia J.; Nassar, Eduardo J., E-mail: eduardo.nassar@unifran.edu.br

2016-02-15

Thin luminescent films have seen great technological advances and are applicable in the production of a variety of materials such as sensors, solar cells, photovoltaic devices, optical magnetic readers, waveguides, lasers, and recorders. Systems that contain yttrium aluminum oxide are important hosts for lanthanide ions and serve as light emission devices. This work deals with the deposition of yttrium aluminum garnet (YAG) film doped with Eu{sup 3+} onto a glass substrate obtained by the sol–gel methodology. Spray pyrolysis furnished the yttrium aluminum oxide powder. Dip-coating at a withdrawal speed of 10 mm min{sup −1} and evaporation led to deposition of different numbers of layers of the YAG:Eu{sup 3+} film onto the glass substrate from a YAG:Eu{sup 3+} powder suspension containing ethanol, water, and tetraethylorthosilicate. Photoluminescence, X-ray diffraction, scanning electron microscopy, and transparency measurements aided film characterization. The emission spectra revealed that the number of layers influenced film properties. - Highlights: • The spray pyrolysis was used to obtain luminescent YAG:Eu{sup 3+}. • The matrix was deposited as transparent films. • The YAG:Eu{sup 3+} was deposited by sol–gel process onto glass substrate.

Yttrium addition for high temperatures stainless steel

International Nuclear Information System (INIS)

Furtado, Nelson Cesar Chaves Pinto

1997-07-01

The current work studied the effect of Yttrium on the microstructure of 2% Nb, modified - HP steel, with respect to its mechanical properties. Alloys were prepared with nominal Yttrium additions of 0,1% and 0,25%. Microstructural analyses and mechanical tests were undertaken in the as-cast condition and after ageing for 100 h at 700 deg C, 900 deg C and 1100 deg C. Structural characterization was performed by optical microscopy, scanning and transmission electron microscopy (SEM/TEM/EDS), X-ray diffractometry and X-ray photoelectron spectroscopy (XPS). Tensile testing was performed at room temperature and 871 deg C and creep testing at 925 deg C at a loading of 55 MPa. The material produced exhibited superior mechanical properties and surface oxidation resistance than traditional alloys of this class, even through gravity cast in a magnetic furnace. Agglomerates of Yttrium-rich phases were identifies in both as-cast and aged specimens, always associated with chromium carbides of characteristic morphologies. These morphologies, combined with the microstructural constituents, may have established the factors which resulted in the improved metallurgical stability of these alloys under the experimental testing conditions and temperatures which simulated real industrial service conditions and temperatures. (author)

Yttrium aluminum garnet coating on glass substrate

International Nuclear Information System (INIS)

Ferreira, Camila M.A.; Freiria, Gabriela S.; Faria, Emerson H. de; Rocha, Lucas A.; Ciuffi, Katia J.; Nassar, Eduardo J.

2016-01-01

Thin luminescent films have seen great technological advances and are applicable in the production of a variety of materials such as sensors, solar cells, photovoltaic devices, optical magnetic readers, waveguides, lasers, and recorders. Systems that contain yttrium aluminum oxide are important hosts for lanthanide ions and serve as light emission devices. This work deals with the deposition of yttrium aluminum garnet (YAG) film doped with Eu 3+ onto a glass substrate obtained by the sol–gel methodology. Spray pyrolysis furnished the yttrium aluminum oxide powder. Dip-coating at a withdrawal speed of 10 mm min −1 and evaporation led to deposition of different numbers of layers of the YAG:Eu 3+ film onto the glass substrate from a YAG:Eu 3+ powder suspension containing ethanol, water, and tetraethylorthosilicate. Photoluminescence, X-ray diffraction, scanning electron microscopy, and transparency measurements aided film characterization. The emission spectra revealed that the number of layers influenced film properties. - Highlights: • The spray pyrolysis was used to obtain luminescent YAG:Eu 3+ . • The matrix was deposited as transparent films. • The YAG:Eu 3+ was deposited by sol–gel process onto glass substrate.

Yttrium-90 microspheres for the treatment of hepatocellular carcinoma.

Science.gov (United States)

Geschwind, Jean Francois H; Salem, Riad; Carr, Brian I; Soulen, Michael C; Thurston, Kenneth G; Goin, Kathleen A; Van Buskirk, Mark; Roberts, Carol A; Goin, James E

2004-11-01

Unresectable hepatocellular carcinoma is extremely difficult to treat. TheraSphere consists of yttrium-90 (a pure beta emitter) microspheres, which are injected into the hepatic arteries. This article reviews the safety and survival of patients with hepatocellular carcinoma who were treated with yttrium-90 microspheres. Eighty patients were selected from a database of 108 yttrium-90 microsphere-treated patients and were staged by using Child-Pugh, Okuda, and Cancer of the Liver Italian Program scoring systems. Patients were treated with local, regional, and whole-liver approaches. Survival from first treatment was analyzed with Kaplan-Meier and Cox regression methods. Adverse events and complications of treatment were coded by using the Southwest Oncology Group toxicity scoring system. Patients received liver doses ranging from 47 to 270 Gy. Thirty-two patients (40%) received more than 1 treatment. Survival correlated with pretreatment Cancer of the Liver Italian Program scores ( P = .002), as well as with the individual Cancer of the Liver Italian Program components, Child-Pugh class, alpha-fetoprotein levels, and percentage of tumor replacement. Patients classified as Okuda stage I (n = 54) and II (n = 26) had median survival durations and 1-year survival rates of 628 days and 63%, and 384 days and 51%, respectively ( P = .02). One patient died of liver failure judged as possibly related to treatment. Thus, in selected patients with hepatocellular carcinoma, yttrium-90 microsphere treatment is safe and well tolerated. On the basis of these results, a randomized controlled trial is warranted comparing yttrium-90 microsphere treatment with transarterial chemoembolization by using the Cancer of the Liver Italian Program system for prospective stratified randomization.

Synthesis of yttrium silicate luminescent materials by sol-gel method

International Nuclear Information System (INIS)

Arkhipov, D.V.; Vasina, O.Yu.; Popovich, N.V.; Galaktionov, S.S.; Soshchin, N.P.

1996-01-01

Several yttrium-silicate composition with Y 2 O 3 content within 44-56% have been synthesized. it is ascertained that employment of sol-gel technique permits preparation of luminescent materials on yttrium silicate basis, which compare favourably with bath-produced specimens. The influence of phase composition of sol-gel phosphors on basic performance indices: intensity and luminescence spectrum, has been analyzed

Study of behaviour of lanthanum- and yttrium electrodes in chloride melts

International Nuclear Information System (INIS)

Shkol'nikov, S.I.; Tolypin, E.S.; Yur'ev, B.P.

1984-01-01

A study was made on the lanthanum- and yttrium behaviour in a mixture of molten potassium- and sodium chlorides at various temperatures. It is shown that the lanthanum- and yttrium behaviour in KCl-NaCl melt is similar to the behaviour of other metals. Their corrosion rate is much higher as compared to other metals and it grows rapidly with increasing melt temperature. The temperature growth by 200 deg C results in an increase in the corrosion rate almost by an order. The potentials of lanthanum- and yttrium electrodes at the instant they are immersed in the melt have more negative values than the potentials of alkali metals under similar conditions

Hydrothermal synthesis and formation mechanism of hexagonal yttrium hydroxide fluoride nanobundles

International Nuclear Information System (INIS)

Tian, Li; Sun, QiLiang; Zhao, RuiNi; He, HuiLin; Xue, JianRong; Lin, Jun

2013-01-01

Graphical abstract: The formation of yttrium hydroxide fluorides nanobundles can be expressed as a precipitation transformation from cubic NaYF 4 to hexagonal NaYF 4 and to hexagonal Y(OH) 2.02 F 0.98 owing to ion exchange. - Highlights: • Novel Y(OH) 2.02 F 0.98 nanobundles have been successfully prepared by hydrothermal method. • The branched nanobundles composed of numerous oriented-attached nanoparticles has been studied. • The growth mechanism is proposed to be ion exchange and precipitation transformation. - Abstract: This article presents the fabrication of hexagonal yttrium hydroxide fluoride nanobundles via one-pot hydrothermal process, using yttrium nitrate, sodium hydroxide and ammonia fluoride as raw materials to react in propanetriol solvent. The X-ray diffraction pattern clearly reveals that the grown product is pure yttrium hydroxide fluoride, namely Y(OH) 2.02 F 0.98 . The morphology and microstructure of the synthesized product is testified to be nanobundles composed of numerous oriented-attached nanoparticles as observed from the field emission scanning electron microscopy (FESEM). The chemical composition was analyzed by the energy dispersive spectrum (EDS), confirming the phase transformation of the products which was clearly consistent with the result of XRD analysis. It is proposed that the growth of yttrium hydroxide fluoride nanobundles be attributed to ion exchange and precipitation transformation

(n,xn cross section measurements for Y-89 foils used as detectors for high energy neutron measurements in the deeply subcritical assembly “QUINTA”

Directory of Open Access Journals (Sweden)

Bielewicz Marcin

2017-01-01

Full Text Available Study of the deep subcritical systems (QUINTA using relativistic beams is performed within the project “Energy and Transmutation of Radioactive Wastes” (E&T – RAW. The experiment assembly was irradiated by deuteron/proton beam (Dubna NUCLOTRON. We calculated the neutron energy spectrum inside the whole assembly by using threshold energy (n,xn reactions in yttrium (Y-89 foils. There are almost no experimental cross section data for those reactions. New Y-89(n,xn cross section measurements were carried out at The Svedberg laboratory (TSL in Uppsala, Sweden in 2015. In this paper we present preliminary results of those experiments.

Lanthanoid and yttrium tellurates

Energy Technology Data Exchange (ETDEWEB)

Gonalez, C G; Guedes de Carvalho, R A [Faculdade de Engenharia, Porto (Portugal). Centro de Engenharia Quimica

1978-05-01

Preparation in aqueous medium of all the lanthanoid (except Ce and Pm) and yttrium tellurates is described. Chemical analyses, solubilities at 25/sup 0/C in water and thermograms of all the products prepared were determined. X-ray diffractograms and DTA and DTG curves of La, Gd and Yb tellurates were obtained and commented. Partial volatilization of lanthanoid is observed in the thermal analysis of tellurates.

New hydrotalcite-like compounds containing yttrium

Energy Technology Data Exchange (ETDEWEB)

Fernandez, J.M.; Barriga, C.; Ulibarri, M.A. [Universidad de Cordoba (Spain)] [and others

1997-01-01

The synthesis of hydrotalcite-type compounds containing yttrium was carried out by the coprecipitation of Mg(II), Al(III), and Y(III) cations at 60 degrees C with strong alkaline solutions. Thermal treatments were applied and changes studied.

Magnetic structure of holmium-yttrium superlattices

DEFF Research Database (Denmark)

Jehan, D.A.; McMorrow, D.F.; Cowley, R.A.

1993-01-01

We present the results of a study of the chemical and magnetic structures of a series of holmium-yttrium superlattices and a 5000 angstrom film of holmium, all grown by molecular-beam epitaxy. By combining the results of high-resolution x-ray diffraction with detailed modeling, we show...... that the superlattices have high crystallographic integrity: the structural coherence length parallel to the growth direction is typically almost-equal-to 2000 angstrom, while the interfaces between the two elements are well defined and extend over approximately four lattice planes. The magnetic structures were...... determined using neutron-scattering techniques. The moments on the Ho3+ ions in the superlattices form a basal-plane helix. From an analysis of the superlattice structure factors of the primary magnetic satellites, we are able to determine separately the contributions made by the holmium and yttrium...

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation

International Nuclear Information System (INIS)

Innocenzi, Valentina; De Michelis, Ida; Ferella, Francesco; Beolchini, Francesca; Kopacek, Bernd; Vegliò, Francesco

2013-01-01

Highlights: • Treatment of fluorescent powder of CRT waste. • Factorial experimental designs to study acid leaching of fluorescent powder and the purification of leach liquors. • Recover of yttrium by precipitation using oxalic acid. • Suitable flowsheet to recover yttrium from fluorescent powder. - Abstract: This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2 2 full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H 2 O 2 concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction. Two series of precipitation tests for zinc are carried out: a 2 2 full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na 2 S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation

Energy Technology Data Exchange (ETDEWEB)

Innocenzi, Valentina, E-mail: valentina.innocenzi1@univaq.it [Department of Industrial Engineering and Information and Economy, University of L’Aquila, Via Giovanni Gronchi n.18, Nucleo Ind.le di Pile, 67100 L’Aquila (Italy); De Michelis, Ida; Ferella, Francesco [Department of Industrial Engineering and Information and Economy, University of L’Aquila, Via Giovanni Gronchi n.18, Nucleo Ind.le di Pile, 67100 L’Aquila (Italy); Beolchini, Francesca [Department of Marine Sciences, Polytechnic Institute of Marche, Via Brecce Bianche, 60131 Ancona (Italy); Kopacek, Bernd [SAT, Austrian Society for Systems Engineering and Automation, Gurkasse 43/2, A-1140 Vienna (Austria); Vegliò, Francesco [Department of Industrial Engineering and Information and Economy, University of L’Aquila, Via Giovanni Gronchi n.18, Nucleo Ind.le di Pile, 67100 L’Aquila (Italy)

2013-11-15

Highlights: • Treatment of fluorescent powder of CRT waste. • Factorial experimental designs to study acid leaching of fluorescent powder and the purification of leach liquors. • Recover of yttrium by precipitation using oxalic acid. • Suitable flowsheet to recover yttrium from fluorescent powder. - Abstract: This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2{sup 2} full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3 M of sulphuric acid, 10% v/v of H{sub 2}O{sub 2} concentrated solution at 30% v/v, 10% w/w pulp density, 70 °C and 3 h of reaction. Two series of precipitation tests for zinc are carried out: a 2{sup 2} full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2–2.5% and 10–12% v/v of Na{sub 2}S concentrated solution at 10% w/v. In these conditions the coprecipitation of yttrium is of 15–20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75–80%.

Production of Y-86 and other radiometals for research purposes using a solution target system

International Nuclear Information System (INIS)

Oehlke, Elisabeth; Hoehr, Cornelia; Hou, Xinchi; Hanemaayer, Victoire; Zeisler, Stefan; Adam, Michael J.; Ruth, Thomas J.; Celler, Anna; Buckley, Ken; Benard, Francois; Schaffer, Paul

2015-01-01

Introduction: Diagnostic radiometals are typically obtained from cyclotrons by irradiating solid targets or from radioisotope generators. These methods have the advantage of high production yields, but require additional solid target handling infrastructure that is not readily available to many cyclotron facilities. Herein, we provide an overview of our results regarding the production of various positron-emitting radiometals using a liquid target system installed on a 13 MeV cyclotron at TRIUMF. Details about the production, purification and quality control of 89 Zr, 68 Ga and for the first time 86 Y are discussed. Methods: Aqueous solutions containing 1.35–1.65 g/mL of natural-abundance zinc nitrate, yttrium nitrate, and strontium nitrate were irradiated on a 13 MeV cyclotron using a standard liquid target. Different target body and foil materials were investigated for corrosion. Production yields were calculated using theoretical cross-sections from the EMPIRE code and compared with experimental results. The radioisotopes were extracted from irradiated target material using solid phase extraction methods adapted from previously reported methods, and used for radiolabelling experiments. Results: We demonstrated production quantities that are sufficient for chemical and biological studies for three separate radiometals, 89 Zr (A sat = 360 MBq/μA and yield = 3.17 MBq/μA), 86 Y (A sat = 31 MBq/μA and yield = 1.44 MBq/μA), and 68 Ga (A sat = 141 MBq/μA and yield = 64 MBq/μA) from one hour long irradiations on a typical medical cyclotron. 68 Ga yields were sufficient for potential clinical applications. In order to avoid corrosion of the target body and target foil, nitrate solutions were chosen as well as niobium as target-body material. An automatic loading system enabled up to three production runs per day. The separation efficiency ranged from 82 to 99%. Subsequently, 68 Ga and 86 Y were successfully used to radiolabel DOTA-based chelators while

Recovery of yttrium from cathode ray tubes and lamps’ fluorescent powders: experimental results and economic simulation

International Nuclear Information System (INIS)

Innocenzi, V.; De Michelis, I.; Ferella, F.; Vegliò, F.

2013-01-01

Highlights: • Fluorescent powder of lamps. • Fluorescent powder of cathode ray rubes. • Recovery of yttrium from fluorescent powders. • Economic simulation for the processes to recover yttrium from WEEE. - Abstract: In this paper, yttrium recovery from fluorescent powder of lamps and cathode ray tubes (CRTs) is described. The process for treating these materials includes the following: (a) acid leaching, (b) purification of the leach liquors using sodium hydroxide and sodium sulfide, (c) precipitation of yttrium using oxalic acid, and (d) calcinations of oxalates for production of yttrium oxides. Experimental results have shown that process conditions necessary to purify the solutions and recover yttrium strongly depend on composition of the leach liquor, in other words, whether the powder comes from treatment of CRTs or lamp. In the optimal experimental conditions, the recoveries of yttrium oxide are about 95%, 55%, and 65% for CRT, lamps, and CRT/lamp mixture (called MIX) powders, respectively. The lower yields obtained during treatments of MIX and lamp powders are probably due to the co-precipitation of yttrium together with other metals contained in the lamps powder only. Yttrium loss can be reduced to minimum changing the experimental conditions with respect to the case of the CRT process. In any case, the purity of final products from CRT, lamps, and MIX is greater than 95%. Moreover, the possibility to treat simultaneously both CRT and lamp powders is very important and interesting from an industrial point of view since it could be possible to run a single plant treating fluorescent powder coming from two different electronic wastes

Pressure of saturated vapor of yttrium and zirconium acetylacetonates

Energy Technology Data Exchange (ETDEWEB)

Trembovetskij, G.V.; Berdonosov, S.S.; Murav' eva, I.A.; Martynenko, L.I. (Moskovskij Gosudarstvennyj Univ. (USSR))

1984-08-01

The static method and the flow method using /sup 91/Y and /sup 95/Zr radioactive indicators have been applied to determine pressure of saturated vapour of yttrium and zirconium acetylacetonates. Values of thermodynamic functions ..delta..Hsub(subl)=(98+-16)kJ/mol and ..delta..Ssub(subl.)=(155+-30)J/mol x K are calculated for sublimation of yttrium acetylacetonate. For sublimation of zirconium acetylacetonates ..delta..Hsub(subl) equals (116+-38) kJ/mol and ..delta..Ssub(subl) is equal to (198+-65) J/molxK.

Structural and dielectric properties of yttrium substituted nickel ferrites

International Nuclear Information System (INIS)

Ognjanovic, Stevan M.; Tokic, Ivan; Cvejic, Zeljka; Rakic, Srdjan; Srdic, Vladimir V.

2014-01-01

Graphical abstract: - Highlights: • Dense NiFe 2−x Y x O 4 ceramics (with 0 ≤ x ≤ 0.3) were prepared. • Pure spinels were obtained for x ≤ 0.07 while for x ≥ 0.15 samples had secondary phases. • With addition of yttrium, ac conductivity slightly increased. • We suggest several effects that can explain the observed changes in ac conduction. • With addition of yttrium, dielectric constant increased while the tg δ decreased. - Abstract: The influence of Y 3+ ions on structural and dielectric properties of nickel ferrites (NiFe 2−x Y x O 4 , where 0 ≤ x ≤ 0.3) has been studied. The as-synthesized samples, prepared by the co-precipitation method, were analyzed by XRD and FTIR which suggested that Y 3+ ions were incorporated into the crystal lattice for all the samples. However, the XRD analysis of the sintered samples showed that secondary phases appear in the samples with x > 0.07. The samples have densities greater than 90% TD and the SEM images showed that the grain size decreases with the addition of yttrium. Dielectric properties measured from 150 to 25 °C in the frequency range of 100 Hz–1 MHz showed that the addition of yttrium slightly increases the ac conductivity and decreases the tg δ therefore making the materials better suited for the use in microwave devices

Inner-sphere and outer-sphere complexes of yttrium(III), lanthanum (III), neodymium(III), terbium(III) and thulium(III) with halide ions in N,N-dimethylformamide

International Nuclear Information System (INIS)

Takahashi, Ryouta; Ishiguro, Shin-ichi

1991-01-01

The formation of chloro, bromo and iodo complexes of yttrium(III), and bromo and iodo complexes of lanthanum(III), neodymium(III), terbium(III) and thulium(III) has been studied by precise titration calorimetry in N,N-dimethylformamide (DMF) at 25 o C. The formation of [YCl] 2+ , [YCl 2 ] + , [YCl 3 ] and [YCl 4 ] - , and [MBr] 2+ and [MBr 2 ] + (M = Y, La, Nd, Tb, Tm) was revealed, and their formation constants, enthalpies and entropies were determined. It is found that the formation enthalpies change in the sequence ΔH o (Cl) > ΔH o (l), which is unusual for hard metal (III) ions. This implies that, unlike the chloride ion, the bromide ion forms outer-sphere complexes with the lanthanide(III) and yttrium(III) ions in DMF. Evidence for either an inner- or outer-sphere complex was obtained from 89 Y NMR spectra for Y(ClO 4 ) 3 , YCl 3 and YBr 3 DMF solutions at room temperature. (author)

Yttrium implantation and addition element effects on the oxidation behaviour of reference steels at 973 K

Energy Technology Data Exchange (ETDEWEB)

Caudron, E.; Buscail, H.; Cueff, R.; Issartel, C.; El Messki, S.; Perrier, S.; Riffard, F. [Lab. Vellave d' Elaboration et d' Etude des Materiaux, Univ. Blaise Pascal Clermont-Fd 2, Le Puy en Velay (France)

2004-07-01

Yttrium implantation effects on reference steels (extra low carbon and low manganese steel) were studied by rutherford backscattering spectrometry (RBS), reflection high energy electron diffraction (RHEED), X-ray diffraction (XRD) and glancing angle X-ray diffraction (GAXRD). Thermogravimetry and in situ X-ray diffraction at 700 C and P{sub O2}=0.04 Pa for 24h were used to determine the yttrium implantation and addition element effects on sample oxidation resistance at high temperatures. This study clearly shows that yttrium implantation and subsequent high temperature oxidation induced the formation of several yttrium mixed oxides which closely depend on the reference steel addition elements. Moreover, these yttrium mixed oxides seem to be responsible for the improved reference steel oxidation resistance at high temperatures. (orig.)

Treatment of rheumatoid arthritis with 90yttrium. Follow up studies

International Nuclear Information System (INIS)

Teuber, J.; Baenkler, H.W.; Regler, G.; Erlangen-Nuernberg Univ., Erlangen

1978-01-01

90 Yttrium-silicate was injected into 131 knee-joints from patients with rheumatoid arthritis with stadium II-IV according to Steinbrocker. The observation period lasted until two years. After three months about 80% and after 24 months still more than 50% of the patients treated showed complete or partial remission. Side-effects as formerly observed with 198 -goldpreparations did not occur. Therefore the treatment with 90 Yttrium-silicate offers an alternative to surgical synovectomy. (orig.) [de

Scandium, yttrium and the lanthanide metals

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

The hydroxide and oxide phases that exist for scandium(III) include scandium hydroxide, which likely has both amorphous and crystalline forms, ScOOH(s), and scandium oxide. This chapter presents the data selected for the stability constants of the polymeric hydrolysis species of scandium at zero ionic strength. The behaviour of yttrium, and the lanthanide metals, in the environment is largely dependent on their solution equilibria. Hydrolysis and other complexation reactions of yttrium and the lanthanide metals are important in the disposal of nuclear waste. The trivalent lanthanide metals include lanthanum(III) through lutetium(III). A number of studies have reported a tetrad effect for the geochemical behaviour of the lanthanide series, including stability constants and distribution coefficients. The solubility of many of the lanthanide hydroxide phases has been studied at fixed ionic strength. In studying the hydrolysis of cerium(IV), a number of studies have utilised oxidation-reduction reactions in determining the relevant stability constants.

Determination of copper oxidizing power in superconducting yttrium ceramics

International Nuclear Information System (INIS)

Pontaler, R.P.; Lebed', N.B.

1989-01-01

A new photometric method for determining the formal copper degree of oxidation and oxygen deficiency in superconducting high-temperature oxides containing yttrium, barium and copper is developed. The method is based on oxidation of Co(2) complex with EDTA by Cu(3) ions in acetrate buffer solution with pH 4.2-4.7 and allows one to determine 1-10% of Cu(3). Relative standard deviation when determining Cu(3) makes up 0.03-0.05. Using a qualitative reaction with the application of sodium vanadate hydrochloride solution the absence of peroxide compound in superconducting yttrium ceramics is ascertained

Enrichment of yttrium from rare earth concentrate by ammonium carbonate leaching and peroxide precipitation

International Nuclear Information System (INIS)

Vasconcellos, Mari E. de; Rocha, S.M.R. da; Pedreira, W.R.; Queiroz S, Carlos A. da; Abrao, Alcidio

2006-01-01

The rare earth elements (REE) solubility with ammonium carbonate vary progressively from element to element, the heavy rare earth elements (HRE) being more soluble than the light rare earth elements (LRE). Their solubility is function of the carbonate concentration and the kind of carbonate as sodium, potassium and ammonium. In this work, it is explored this ability of the carbonate for the dissolution of the REE and an easy separation of yttrium was achieved using the precipitation of the peroxide from complex yttrium carbonate. For this work is used a REE concentrate containing (%) Y 2 O 3 2.4, Dy 2 O 3 0.6, Gd 2 O 3 2.7, CeO 2 2.5, Nd 2 O 3 33.2, La 2 O 3 40.3, Sm 2 O 3 4.1 and Pr 6 O 11 7.5. The mentioned concentrate was produced industrially from the chemical treatment of monazite sand by NUCLEMON in Sao Paulo. The yttrium concentrate was treated with 200 g L -1 ammonium carbonate during 10 and 30 min at room temperature. The experiments indicated that a single leaching operation was sufficient to get a rich yttrium solution with about 60.3% Y 2 O 3 . In a second step, this yttrium solution was treated with an excess of hydrogen peroxide (130 volumes), cerium, praseodymium and neodymium peroxides being completely precipitated and separated from yttrium. Yttrium was recovered from the carbonate solution as the oxalate and finally as oxide. The final product is an 81% Y 2 O 3 . This separation envisages an industrial application. The work discussed the solubility of the REE using ammonium carbonate and the subsequent precipitation of the correspondent peroxides

Fluorimetric determination of yttrium by methyl-bis(8-hydraxy--- 2-quinolyl)amine

International Nuclear Information System (INIS)

Golovina, A.P.; Kachin, S.V.; Runov, V.K.; Fakeeva, O.A.

1982-01-01

Using a method of mathematical Box-Wilson experiment planning the optimum conditions of yttrium fluorimetric determination by methyl-bis (8-hydroxy-2-quinolyl) amine (pH 7.5, csub(R)=1.4x10sup(-5) M) with the determination limit=0.05 μg/ml are found. An extraction-fluorimetric method of yttrium determination by methyl-bis (8-hydroxy-2-quinolyl) amine is developed. The extraction has been realized with aliphatic alcohols at pH > 11. The method is characteristic of the lowest determination limit (0.01 μg/ml) as compared with the known ones. The possibility is shown of yttrium determination in the presence of 5000-multiple aluminium contents, stoichiometric contents of La, Lu, Fe (3), U (6), tartrates, citrates

Spectroscopic properties of Er/Nd co-doped yttrium lanthanum oxide transparent ceramics pumped at 980 nm

Energy Technology Data Exchange (ETDEWEB)

Shao, Yingjie; Yang, Qiuhong, E-mail: yangqiuhong@shu.edu.cn; Gui, Yan; Yuan, Ye; Lu, Qing

2016-05-15

(Er{sub 0.01}Nd{sub x}Y{sub 0.89-x}La{sub 0.1}){sub 2}O{sub 3} (x = 0, 0.001, 0.002, 0.005, 0.01) transparent ceramics were prepared by conventional ceramic processing. The Nd{sup 3+} content dependencies of mid-infrared, near infrared and up-conversion emission of Er{sup 3+} pumped at 980 nm were fully presented. Mechanism of energy transfer between Er{sup 3+} and Nd{sup 3+} was also demonstrated. The results showed that co-doping 0.1 at% Nd{sup 3+} into 1 at% Er{sup 3+} doped yttrium lanthanum oxide transparent ceramic enhanced the 2.7 μm emission significantly and meanwhile suppressed the 1.5 μm emission effectively which indicated an improvement in population inversion between Er:{sup 4}I{sub 11/2} and Er:{sup 4}I{sub 13/2}. Moreover, green up-conversion emission of Er{sup 3+} ion also showed a great improvement by co-doping 0.1 at% Nd{sup 3+}. Those great results were attributed to energy recycle from Er:{sup 4}I{sub 13/2} to Er:{sup 4}I{sub 11/2}. The energy recycle was mainly built by the two energy transfer between Er{sup 3+} and Nd{sup 3+} (one is from Er to Nd, another is in opposite way). So, Er/Nd co-doped yttrium lanthanum oxide transparent ceramic with Nd in low concentration can be considered as a promising laser material for ∼3 μm and up-conversion laser application. - Highlights: • (Er{sub 0.01}Nd{sub x}Y{sub 0.89-x}La{sub 0.1}){sub 2}O{sub 3} transparent ceramics were prepared. • The emission of 2.7 μm of Er{sup 3+} ion was significantly enhanced as x was 0.001. • The emission of 1.5 μm of Er{sup 3+} ion was suppressed greatly by co-doping Nd{sup 3+} ion. • Mechanism of Er–Nd energy transfer was discussed by the energy sketch.

Impacts of yttrium substitution on FMR line-width and magnetic properties of nickel spinel ferrites

Energy Technology Data Exchange (ETDEWEB)

Ishaque, M., E-mail: ishaqdgk1@gmail.com [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Khan, Muhammad Azhar, E-mail: azhar.khan@iub.edu.pk [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Ali, Irshad; Khan, Hasan M. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Iqbal, M. Asif [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); College of E & ME, National University of Science and Technology, Islamabad (Pakistan); Islam, M.U. [Department of Physics, Bahauddin Zakariya University, Multan 60800 (Pakistan); Warsi, Muhammad Farooq [Department of Chemistry, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan)

2015-05-15

The influence of yttrium (Y) substitution on ferromagnetic resonance (FMR), initial permeability, and magnetic properties of NiFe{sub 2}O{sub 4} ferrites were investigated. It was observed that the FMR line-width decreases with yttrium contents for the substitution level 0≤×≤0.06. Beyond this, the FMR line-width increases with yttrium contents. The nominal composition NiY{sub 0.12}Fe{sub 1.88}O{sub 4} exhibited the smallest FMR line-width ~282 Oe. A significant change in FMR position of nickel–yttrium (Ni–Y) ferrites was observed and it found to exist between 4150 and 4600 Oe. The saturation magnetization was observed to decrease with the increase of yttrium contents and this was referred to the redistribution of cations on octahedral. The coercivity increased from 15 Oe to 59 Oe by increasing the yttrium concentration. The initial permeability decreased from 110 to 35 at 1 MHz by the incorporation of yttrium and this was attributed to the smaller grains which may obstruct the domain wall movement and impede the domain wall motion. The magnetic loss factors of substituted samples exhibit decreasing behavior in the frequency range 1 kHz to 10 MHz. The smaller FMR line-width and reduced magnetic loss factor of the investigated samples suggest the possible use of these materials in high frequency applications. - Highlights: • Influence of Y{sup 3+} substitution on the properties of nickel ferrites is investigated. • Very small FMR line-width (282 Oe) is exhibited by these substituted ferrites. • Fourfold increase in coercivity was observed for NiY{sub 0.24}Fe{sub 1.76}O{sub 4} ferrites.

Studies for the yttrium determination by activation analysis, in the presence of lanthanides. Application of the substoichiometric technique

International Nuclear Information System (INIS)

Silva, D.I.T. da.

1978-01-01

Some methods using extraction chromatography for the separation of yttrium from the lanthanide elements were applied. The separation of yttrium was studied, using di-(2 ethylhexyl) orthophosphoric acid as stationary phase, Kieselguhr as support and HNO 3 of concentration between 4,5 and 5,0 N as the mobile phase. In these conditions, about 50% of pure yttrium was obtained. The substoichiometric technique was applied to the determination of yttrium. The elements was partially complexed and the Y 3 + ions were separated from the complex (EDTA-Y) - by means of a cationic resin. The sensitivity, precision and accuracy which can be expected in the analytical results were studied. The possibility of the analysis of a sample containing 1 part per million of yttrium with an error just above 8% was demonstrated. It was also shown that, admitting an error of 10%, it is possible to determine 60 parts per billion of yttrium [pt

Yttrium-90

International Nuclear Information System (INIS)

Ammerich, Marc; Frot, Patricia; Gambini, Denis-Jean; Gauron, Christine; Moureaux, Patrick; Herbelet, Gilbert; Lahaye, Thierry; Pihet, Pascal; Rannou, Alain; Vial, Eric

2013-03-01

This sheet belongs to a collection which relates to the use of radionuclides essentially in unsealed sources. Its goal is to gather on a single document the most relevant information as well as the best prevention practices to be implemented. These sheets are made for the persons in charge of radiation protection: users, radioprotection-skill persons, labor physicians. Each sheet treats of: 1 - the radio-physical and biological properties; 2 - the main uses; 3 - the dosimetric parameters; 4 - the measurement; 5 - the protection means; 6 - the areas delimitation and monitoring; 7 - the personnel classification, training and monitoring; 8 - the effluents and wastes; 9 - the authorization and declaration administrative procedures; 10 - the transport; and 11 - the right conduct to adopt in case of incident or accident. This sheet deals specifically with Yttrium-90

Cathodoluminescence properties of yttrium aluminum garnet doped with Eu2+ and Eu3+ ions

International Nuclear Information System (INIS)

Trofimov, A. N.; Petrova, M. A.; Zamoryanskaya, M. V.

2007-01-01

Yttrium aluminium garnet (YAG) doped with Eu 2+ and Eu 3+ ions is very interesting as a phosphor for conversion of light-emitting diode light for white light sources. The europium ion occupies the structural position of yttrium in yttrium aluminium garnet and has valence state Eu 3+ . Our sample was doped with Zr 4+ , which is why some of the europium ions had valence state Eu 2+ . As a rule, luminescence of Eu 3+ ions is observed in the orange and red range of spectrum. The luminescence of Eu 2+ in yttrium aluminum garnet is characterized by an intensive broad band with maximum of intensity at about 560 nm (green color). In this work, we studied the intensity and decay time dependences on europium concentration, and the influence of excitation power density on the cathodoluminescence of the sample. The most interesting result is the change of visible cathodoluminescence color in dependence on the density of the exciting power

Method for production of transparent yttrium oxide

International Nuclear Information System (INIS)

Dutta, S.K.; Gazza, G.A.

1975-01-01

The method comprises vacuum hot pressing the yttrium oxide (Y 2 O 3 ) powder in a graphite die at temperatures of between 1300 to 1500 0 C and uniaxial pressures of between 5000 to 7000 psi, for a period of 1 to 2 hours. (U.S.)

Study of decomposition kinetics of volatile β-diketonates of yttrium, barium and copper in flow reactor

International Nuclear Information System (INIS)

Devyatykh, G.G.; Gavrishchuk, E.M.; Gibin, A.M.; Dadanov, A.Yu.; Dzyubenko, N.G.; Kaul', A.R.; Nichiporuk, R.V.; Snezhko, N.T.; Ul'yanov, A.A.

1990-01-01

Heterogeneous oxidative decomposition of adduct of yttrium acetylacetonate with o-phenanthroline, copper acetylacetonate and barium dipivaloylmethanate in a flow-type reactor was carried out. The basic kinetic characteristics of chemical precipitation processes of films of yttrium, copper and barium oxides, which are components of high-temperature superconductors, were obtained. The values of activation energy of precipitation process of yttrium, copper and barium oxides constituted 76±10, 108±15, 81±12 (t 600 deg C) respectively

Positive effect of yttrium on the reduction of pores in cast Al alloy

International Nuclear Information System (INIS)

Hua, Guomin; Ahmadi, Hojat; Nouri, Meisam; Li, Dongyang

2015-01-01

Mechanical and electrochemical properties of Al alloys can be improved by adding a small amount of rare-earth such as yttrium. Here we demonstrate that adding yttrium also helps suppress the porosity in cast Al alloys, thus minimizing its detrimental effect on mechanical properties of the alloys. The mechanism behind is elucidated based on the hydrogen binding energies and the diffusion activation energies of hydrogen atoms in Al and Al–Y phases, calculated using the first-principle method. - Highlights: • The porosity of commercial Al alloy can be reduced by additive yttrium. • Formed Al 3 Y phase helps reduce homogeneous nucleation of hydrogen bubbles. • Formed Al 3 Y and Al 2 Y phases could suppress the growth of hydrogen bubbles

Yttrium recovery from primary and secondary sources: A review of main hydrometallurgical processes

Energy Technology Data Exchange (ETDEWEB)

Innocenzi, Valentina, E-mail: valentina.innocenzi1@univaq.it [Department of Industrial Engineering, of Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, Zona industriale di Pile, 67100 L’Aquila (Italy); De Michelis, Ida [Department of Industrial Engineering, of Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, Zona industriale di Pile, 67100 L’Aquila (Italy); Kopacek, Bernd [SAT, Austrian Society for Systems Engineering and Automation, Gurkasse 43/2, A-1140 Vienna (Austria); Vegliò, Francesco [Department of Industrial Engineering, of Information and Economy, University of L’Aquila, Via Giovanni Gronchi 18, Zona industriale di Pile, 67100 L’Aquila (Italy)

2014-07-15

Highlights: • Review of the main hydrometallurgical processes to recover yttrium. • Recovery of yttrium from primary sources. • Recovery of yttrium from e-waste and other types of waste. - Abstract: Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority. The present review summarized the main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes. Before to discuss the works about the treatment of wastes, the processes to retrieval Y from ores are discussed, since the processes are similar and derived from those already developed for the extraction from primary sources. Particular attention was given to the recovery of Y from WEEE because the recycle of them is important not only for economical point of view, considering its value, but also for environmental impact that this could be generated if not properly disposal.

Treatment of acromegaly by yttrium implantation

Energy Technology Data Exchange (ETDEWEB)

Hibbert, J.; Shaheen, O.H.

1977-01-01

Yttrium implantation is one of the many ways of treating acromegaly. The advantages are the minor nature of the procedure and the fact that pituitary replacement is not as commonly required as after hypophysectomy. Thus in young female patients menstruation may be resumed following treatment and pregnancy has occurred. The procedure is not as free from complications as external irradiation but the response is more satisfactory.

Biochemical investigation of yttrium(III) complex containing 1,10-phenanthroline: DNA binding and antibacterial activity.

Science.gov (United States)

Khorasani-Motlagh, Mozhgan; Noroozifar, Meissam; Moodi, Asieh; Niroomand, Sona

2013-03-05

Characterization of the interaction between yttrium(III) complex containing 1,10-phenanthroline as ligand, [Y(phen)2Cl(OH2)3]Cl2⋅H2O, and DNA has been carried out by UV absorption, fluorescence spectra and viscosity measurements in order to investigate binding mode. The experimental results indicate that the yttrium(III) complex binds to DNA and absorption is decreasing in charge transfer band with the increase in amount of DNA. The binding constant (Kb) at different temperatures as well as thermodynamic parameters, enthalpy change (ΔH°) and entropy change (ΔS°), were calculated according to relevant fluorescent data and Vant' Hoff equation. The results of interaction mechanism studies, suggested that groove binding plays a major role in the binding of the complex and DNA. The activity of yttrium(III) complex against some bacteria was tested and antimicrobial screening tests shown growth inhibitory activity in the presence of yttrium(III) complex. Copyright © 2013 Elsevier B.V. All rights reserved.

Preparation, characterization and thermal behaviour study of double selenates of lanthanides, yttrium and beryllium

International Nuclear Information System (INIS)

Ribeiro, C.A.

1988-01-01

The lanthanides (III) and yttrium (III) double selenates were studied using common analytical methods, atomic absorption, X-ray diffraction infra-red absorption, thermogravimetry and differential thermal analysis. These compounds were prepared from the mixture of lanthanides (III) and yttrium (III) selenates aqueous solution and basic beryllium selenates aqueous solution, obeying equimolar relation (1:1) to the cation

Effect of yttrium on the oxide scale adherence of pre-oxidized silicon-containing heat-resistant alloy

International Nuclear Information System (INIS)

Yan Jingbo; Gao Yimin; Shen Yudi; Yang Fang; Yi Dawei; Ye Zhaozhong; Liang Long; Du Yingqian

2011-01-01

Highlights: → AE experiment shows yttrium has a beneficial effect on the pre-oxidized HP40 alloy. → Yttrium facilitates the formation of internal oxide after 10 h of oxidation. → Internal oxide changes the rupture behaviour of the oxide scale. → Twins form in the internal oxide and improve the binding strength of the scale. - Abstract: This paper investigates the effect of the rare earth element yttrium on the rupture behaviour of the oxide scale on the silicon-containing heat-resistant alloy during cooling. After 10 h of oxidation, yttrium is found to facilitate the formation of internal oxides (silica) at the scale-matrix interface. Due to the twinning observed by scanning transmission electron microscopy (STEM) in silica, the critical strain value for the scale failure can be dramatically improved, and the formation of cracks at the scale-matrix interface is inhibited.

Neutron activation determination of oxygen in ceramic materials on the basis of yttrium, barium and copper

International Nuclear Information System (INIS)

Goldshtein, M.M.; Yudelevich, I.G.

1991-01-01

A procedure of determining oxygen in superconducting materials on the basis of yttrium, barium and copper oxides with the application of 14 MeV-neutron activation was developed. The method is based on determining the relation between oxygen and yttrium in the compounds investigated. In order to minimize systematic errors, expressions accounting for spectrometer dead time under conditions of varying component activity are proposed. The procedure ensures determination of the relation between oxygen and yttrium with a relative error of 0.4% with NAA using a neutron generator. (author) 4 refs.; 1 fig

Improvement of the oxidation resistance of Tribaloy T-800 alloy by the additions of yttrium and aluminium

International Nuclear Information System (INIS)

Zhang, Y.-D.; Zhang, C.; Lan, H.; Hou, P.Y.; Yang, Z.-G.

2011-01-01

Research highlights: → The additions of yttrium (Y) reduced the oxidation rate of Tribaloy T-800 alloy. → Y promoted selective oxidation of Cr due to refinement of alloy phase size. → The oxidation rate was further reduced by Y plus Al with a protective Al 2 O 3 scale. → The positive effect of Y and Al being more pronounced at the higher temperature. - Abstract: The microstructures and oxidation behaviour of the modified Tribaloy T-800 alloys by additions of yttrium and yttrium plus aluminium have been studied. At the presence of yttrium alone, the oxidation rate decreased, and the selective oxidation of chromium was promoted, which was related to the refinement of alloy phase size. The addition of yttrium plus aluminium further reduced the oxidation rate. The selective oxidation of chromium and aluminium were both promoted significantly. The benefits were especially pronounced at 1000 o C, with the formation of protective alumina external layer and no internal oxides, which may be detrimental to the alloy mechanical property.

Study on stability of labeled yttrium-90 with lipiodol by chemical extraction for liver cancer

International Nuclear Information System (INIS)

Mu, P.Y.; Jiang, X.L.; Chen, J.; Zhu, Y.J.

2005-01-01

Liver cancer, particularly hepatocellular carcinoma, is one of the most common malignant diseases in many developed and developing countries. It is also one of the most common diseases endangering the people's lives and health heavily. Surgery is very effective in early-stage patients. Unfortunately, there is less than 10% of the patients with hepatocellular carcinoma fitting for surgical therapy. Instead of surgical therapy, other methods are considered for patients in whom surgery may not work well. Systemic administration of chemotherapeutic agents is not often considered in liver cancer patients, due to discouraging result and adverse side effects. Also, hepatocellular carcinoma is not keen on usual radioactive therapy. However, method of inner interventional radioactive nuclide is a potential way to cure liver tumors. Hepatocellular carcinoma would be cured with inner interventional radioactive nuclide, which is a hot topic in experimental research on hepatocellular carcinoma at home and abroad. The purpose of the study is to label Yttrium-90 with lipiodol by means of the chemical extraction method and research the stability of labeled Yttrium-90 ( 90 Y-P204-Lipiodol) in serum of a newly-born cattle and human's blood. We chose to label steady yttrium with lipiodol, because radioactive yttrium has great nuclear character for liver cancer, yttrium-90 can eradiate pure β radial, and it's half time is 64 hours. Average energy of it is 0.93 Mev, the highest energy is 2.27 Mev. Yttrium-90 can be labeled with lipiodol by means of the chemical extraction method, which is mature in chemical techniques, combined with method of radioactive nuclide labeled in. nuclear medicine. At first, yttrium-90 is extracted in certain condition(pH, temperature, whisk time, whisk frequency, etc ) after adding yttrium-90 solution. We use some distilled water to balance the labeled organic phase twice, and test the stability of labeled yttrium-90 in serum of a newly-born cattle and

Effect of yttrium chromite doping on its resistance to high-temperature salt and gas corrosions

International Nuclear Information System (INIS)

Oryshich, I.V.; Poryadchenko, N.E.; Rakitskij, A.N.; Bega, N.D.

1996-01-01

Effect of yttrium chromite doping with 2-4 group metal oxides on the corrosion resistance in the air at 1300 C during 5 hours and in sodium chloride and sulfate melts at 900 C during 20 hours is investigated. A notable increase of corrosion resistance is achieved under complex doping with zirconium and magnesium oxides in a quantity, close to solubility in yttrium oxide and solubility by aluminium oxide. Doping with calcium and strontium oxides in the quantities, dose to solubility in yttrium oxide does not produce any notable effect, and at higher concentrations it reduces the corrosion resistance in media indicated. Refs. 8, refs. 2, tabs. 1

The enhanced visible light photocatalytic activity of yttrium-doped BiOBr synthesized via a reactable ionic liquid

Energy Technology Data Exchange (ETDEWEB)

He, Minqiang; Li, Weibing [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Xia, Jiexiang, E-mail: xjx@ujs.edu.cn [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Xu, Li; Di, Jun [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Xu, Hui [School of the Environment, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Yin, Sheng [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Li, Huaming, E-mail: lhm@ujs.edu.cn [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China); Li, Mengna [School of Chemistry and Chemical Engineering, Jiangsu University, 301 Xuefu Road, Zhenjiang 212013 (China)

2015-03-15

Graphical abstract: Yttrium (Y)-doped BiOBr with different Y doping concentrations has been synthesized via solvothermal method in the presence of reactable ionic liquid 1-hexadecyl-3-methylimidazolium bromide ([C16mim]Br). The photocatalytic activities of the yttrium doped BiOBr samples were evaluated by the degradation of ciprofloxacin (CIP) and rhodamine B (RhB) under visible-light irradiation. The yttrium doped BiOBr exhibited enhanced photocatalytic activity for the degradation of the two types of pollutants, and the 5wt%Y-doped BiOBr showed the highest photocatalytic activity. The enhanced photocatalytic performance could be attributed to the reduced band gap and improved separation of electron–hole pairs. - Highlights: • Yttrium (Y)-doped BiOBr composites have been synthesized via solvothermal method in the presence of reactable ionic liquid [C16mim]Br. • The yttrium doped BiOBr exhibited enhanced photocatalytic activity for the degradation of ciprofloxacin (CIP) and rhodamine B (RhB). • The enhanced photocatalytic performance could be attributed to the reduced band gap and improved separation of electron–hole pairs. - Abstract: Yttrium (Y)-doped BiOBr with different Y doping concentrations has been synthesized via solvothermal method in the presence of reactable ionic liquid 1-hexadecyl-3-methylimidazolium bromide ([C{sub 16}mim]Br). Their structures, morphologies and optical properties were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and UV–vis diffuse reflectance spectroscopy (DRS). The photocatalytic activities of the yttrium doped BiOBr samples were evaluated by the degradation of ciprofloxacin (CIP) and rhodamine B (RhB) under visible-light irradiation. The yttrium doped BiOBr exhibited enhanced photocatalytic activity for the degradation of the two types of pollutants, and the 5wt%Y-doped BiOBr showed the highest

Preparation of high purity yttrium single crystals by electrotransport

International Nuclear Information System (INIS)

Volkov, V.T.; Nikiforova, T.V.; Ionov, A.M.; Pustovit, A.N.; Sikharulidse, G.G.

1981-01-01

The possibility of obtaining yttrium crystals of high purity by the method of solid state electrotransport (SSE) was investigated in the present work. The behaviour of low contents of iron, aluminium, silicon, tantalum, copper, silver and vanadium as metallic impurities was studied using mass spectrometry. It is shown that all the impurities investigated, except copper, migrate to the anode. During electrotransfer a purification with respect to these impurities by a factor of 4 - 6 is obtained. It is proposed that the diffusion coefficients of the metallic impurities investigated are anomalously high and that the behaviour of the impurities during SSE in adapters necessitates further investigation. By using a three-stage process with intermediate removal of the anode end yttrium single crystals with a resistance ratio rho 293 /rhosub(4.2)=570 were produced. (Auth.)

Thermal decomposition of yttrium(III) valerate in argon

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Yue, Zhao; Tang, Xiao

2014-01-01

The thermal decomposition of yttrium(III) valerate (Y(C4H9CO2)3) was studied in argon by means of thermogravimetry, differential thermal analysis, IR-spectroscopy, X-ray diffraction, in-situ synchrotron diffraction and hot-stage microscopy as well as room temperature optical microscopy. Melting...

The reactive element effect of yttrium and yttrium silicon on high temperature oxidation of NiCrAl coating

Science.gov (United States)

Ramandhany, S.; Sugiarti, E.; Desiati, R. D.; Martides, E.; Junianto, E.; Prawara, B.; Sukarto, A.; Tjahjono, A.

2018-03-01

The microstructure formed on the bond coat affects the oxidation resistance, particularly the formation of a protective oxide layer. The adhesion of bond coat and TGO increased significantly by addition of reactive element. In the present work, the effect of yttrium and yttrium silicon as reactive element (RE) on NiCrAl coating was investigated. The NiCrAl (without RE) and NiCrAlX (X:Y or YSi) bond coating were deposited on Hastelloy C-276 substrate by High Velocity Oxygen Fuel (HVOF) method. Isothermal oxidation was carried out at 1000 °C for 100 hours. The results showed that the addition of RE could prevent the breakaway oxidation. Therefore, the coating with reactive element were more protective against high temperature oxidation. Furthermore, the oxidation rate of NiCrAlY coating was lower than NiCrAlYSi coating with the total mass change was ±2.394 mg/cm2 after 100 hours of oxidation. The thickness of oxide scale was approximately 1.18 μm consisting of duplex oxide scale of spinel NiCr2O4 in outer scale and protective α-Al2O3 in inner scale.

Method of growing yttrium aluminate and/or lanthanide single crystals with perovskite structure

International Nuclear Information System (INIS)

Kvapil, Jiri; Perner, B.; Kvapil, Josef; Blazek, K.

1989-01-01

Single crystals of yttrium aluminate and/or lanthanide with perovskite structure are grown from melt in a vacuum at a pressure of gas residues of max. 0.01 Pa. The melt contains 1±0.05 gram-ions of aluminium per gram-ion of yttrium and/or lanthanides. The single crystals are then heated in a vacuum (0.01 Pa) at temperatures of 1,450 to 1,800 degC for 2 to 3 hours. (B.S.)

Yttrium-90 microspheres for the treatment of hepatocellular carcinoma: A review

International Nuclear Information System (INIS)

Salem, Riad; Hunter, Russell D.

2006-01-01

To present a critical review of yttrium-90 (TheraSphere) for the treatment of hepatocellular carcinoma (HCC). Medical literature databases (Medline, Cochrane Library, and CANCERLIT) were searched for available literature concerning the treatment of HCC with TheraSphere. These publications were reviewed for scientific and clinical validity. Studies pertaining to the use of yttrium-90 for HCC date back to the 1960s. The results from the early animal safety studies established a radiation exposure range of 50-100 Gy to be used in human studies. Phase I dose escalation studies followed, which were instrumental in delineating radiation dosimetry and safety parameters in humans. These early studies emphasized the importance of differential arteriolar density between hypervascular HCC and surrounding liver parenchyma. Current trends in research have focused on advancing techniques to safely implement this technology as an alternative to traditional methods of treating unresectable HCC, such as external beam radiotherapy, conformal beam radiotherapy, ethanol ablation, trans-arterial chemoembolization, and radiofrequency ablation. Yttrium-90 (TheraSphere) is an outpatient treatment option for HCC. Current and future research should focus on implementing multicenter phase II and III trials comparing TheraSphere with other therapies for HCC

Yttrium-90 microspheres for the treatment of hepatocellular carcinoma: a review.

Science.gov (United States)

Salem, Riad; Hunter, Russell D

2006-01-01

To present a critical review of yttrium-90 (TheraSphere) for the treatment of hepatocellular carcinoma (HCC). Medical literature databases (Medline, Cochrane Library, and CANCERLIT) were searched for available literature concerning the treatment of HCC with TheraSphere. These publications were reviewed for scientific and clinical validity. Studies pertaining to the use of yttrium-90 for HCC date back to the 1960s. The results from the early animal safety studies established a radiation exposure range of 50-100 Gy to be used in human studies. Phase I dose escalation studies followed, which were instrumental in delineating radiation dosimetry and safety parameters in humans. These early studies emphasized the importance of differential arteriolar density between hypervascular HCC and surrounding liver parenchyma. Current trends in research have focused on advancing techniques to safely implement this technology as an alternative to traditional methods of treating unresectable HCC, such as external beam radiotherapy, conformal beam radiotherapy, ethanol ablation, trans-arterial chemoembolization, and radiofrequency ablation. Yttrium-90 (TheraSphere) is an outpatient treatment option for HCC. Current and future research should focus on implementing multicenter phase II and III trials comparing TheraSphere with other therapies for HCC.

Electrochemical corrosion of lanthanum chromite and yttrium chromite in coal slag

Energy Technology Data Exchange (ETDEWEB)

Marchant, D.D.; Bates, J.L.

1981-01-01

Lanthanum chromites have long been considered as electrodes for magnetohydrodynamic (MHD) generator channels. These chromites, when doped with divalent ions such as Ca, Mg or Sr, have adequate electronic and electrical conductivity (2), and melting points greater than 2500/sup 0/K. However, above approx. 1850/sup 0/K, selective vapor loss of chromium results in the formation of a La/sub 2/O/sub 3/ phase. The La/sub 2/O/sub 3/ is hydroscopic at room temperature, resulting in a large volume change and loss of mechanical integrity when exposed to H/sub 2/O. The analogous yttrium chromites have thermal and electrical properties similar to that for the lanthanum chromites. Although vapor loss of Cr results in the formation of Y/sub 2/O/sub 3/, this oxide does not hydrate. Corrosion studies of yttrium chromite compositions show that doped YCrO/sub 3/ may be a viable MHD electrode. An electrochemical corrosion study of both magnesium-doped lanthanum and yttrium chromites in synthetic coal slag electrolytes is described. Possible chemical and electrochemical degradation phenomena, as well as the relative rates of corrosion are emphasized.

Annotating MYC status with 89Zr-transferrin imaging.

Science.gov (United States)

Holland, Jason P; Evans, Michael J; Rice, Samuel L; Wongvipat, John; Sawyers, Charles L; Lewis, Jason S

2012-10-01

A noninvasive technology that quantitatively measures the activity of oncogenic signaling pathways could have a broad impact on cancer diagnosis and treatment with targeted therapies. Here we describe the development of (89)Zr-desferrioxamine-labeled transferrin ((89)Zr-transferrin), a new positron emission tomography (PET) radiotracer that binds the transferrin receptor 1 (TFRC, CD71) with high avidity. The use of (89)Zr-transferrin produces high-contrast PET images that quantitatively reflect treatment-induced changes in MYC-regulated TFRC expression in a MYC-driven prostate cancer xenograft model. Moreover, (89)Zr-transferrin imaging can detect the in situ development of prostate cancer in a transgenic MYC prostate cancer model, as well as in prostatic intraepithelial neoplasia (PIN) before histological or anatomic evidence of invasive cancer. These preclinical data establish (89)Zr-transferrin as a sensitive tool for noninvasive measurement of oncogene-driven TFRC expression in prostate and potentially other cancers, with prospective near-term clinical application.

High performance yttrium-doped BSCF hollow fibre membranes

DEFF Research Database (Denmark)

Haworth, P.; Smart, S.; Glasscock, Julie

2012-01-01

measurements in air was similar for both compositions, suggesting that the higher oxygen fluxes obtained for BSCFY hollow fibres could be attributed to the higher non-stoichiometry due to yttrium addition to the BSCF crystal structure. In addition, the improvement of oxygen fluxes for small wall thickness (∼0...

Nature of the bifunctional chelating agent used for radioimmunotherapy with yttrium-88 monoclonal antibodies: critical factors in determining in vivo survival and organ toxicity

Energy Technology Data Exchange (ETDEWEB)

Kozak, R.W.; Raubitschek, A.; Mirzadeh, S.; Brechbiel, M.W.; Junghaus, R.; Gansow, O.A.; Waldmann, T.A. (Center for Biologics Evaluation and Research, FDA, Bethesda, MD (USA))

1989-05-15

One factor that is critical to the potential effectiveness of radioimmunotherapy is the design of radiometal-chelated antibodies that will be stable in vivo. Stability in vivo depends on the condition that both the chelate linkage and radiolabeling procedures not alter antibody specificity and biodistribution. In addition, synthesis and selection of the chelating agent is critical for each radiometal in order to prevent inappropriate release of the radiometal in vivo. In the present study, we compare the in vivo stability of seven radioimmunoconjugates that use different polyaminocarboxylate chelating agents to complex yttrium-88 to the mouse anti-human interleukin-2 receptor monoclonal antibody, anti-Tac. Chelate linkage and radiolabeling procedures did not alter the immunospecificity of anti-Tac. In order to assess whether yttrium was inappropriately released from the chelate-coupled antibody in vivo, iodine-131-labeled and yttrium-88 chelate-coupled antibodies were simultaneously administered to the same animals to correlate the decline in yttrium and radioiodinated antibody activity. The four stable yttrium-88 chelate-coupled antibodies studied displayed similar iodine-131 and yttrium-88 activity, indicating minimal elution of yttrium-88 from the complex. In contrast, the unstable yttrium-88 chelate-coupled antibodies had serum yttrium-88 activities that declined much more rapidly than their iodine-131 activities, suggesting loss of the radiolabel yttrium-88 from the chelate. Furthermore, high rates of yttrium-88 elution correlated with deposition in bone. Four chelating agents emerged as promising immunotherapeutic reagents: isothiocyanate benzyl DTPA and its derivatives 1B3M, MX, and 1M3B.

Studies on the separation of {sup 89}Sr(II) from irradiated yttria target using 4, 4{sup '}(5{sup '}) di-tert-butyl-cyclohexano-18-crown-6 (DtBuCH18C6) by solvent extraction technique

Energy Technology Data Exchange (ETDEWEB)

Saha, Debasish; Vithya, Jayagopal; Kumar, Ramalingam; Venkata Subramani, Canchipuram Ramamoorthy; Vasudeva Rao, Polur Ranga [Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam (India). Chemistry Group

2016-07-01

The radioisotope {sup 89}Sr as {sup 89}SrCl{sub 2} is medically useful for bone pain palliation and is produced in fast reactors using the {sup 89}Y(n, p){sup 89}Sr reaction. A procedure for isolation of the radionuclide {sup 89}Sr by chemical processing of the irradiated Y{sub 2}O{sub 3} target has been standardised and trial runs have been carried out at the Fast Breeder Test Reactor (FBTR), Kalpakkam. The chemical processing of the irradiated Y{sub 2}O{sub 3} target involves (i) the removal of target Y(III) by TBP extraction and (ii) further purification of the separated {sup 89}Sr fraction by cationic exchange chromatography. However a selective isolation of {sup 89}Sr by the Sr-specific crown ether makes the above chemical processing faster and relatively simple. This work presents a study on the selective removal of Sr from the irradiated target dissolver solution using the Sr-specific crown ether 4,4{sup '}(5{sup '}) di-tert-butyl-cyclohexano-18-crown-6 (DtBuCH18C6) in octanol medium. The separation behaviour of the other impurities such as Ce(IV), Y(III), Tb(III), Eu(III), Zn(II), Mn(II) and Rb(I) present along with Sr(II) in the irradiated sample was also investigated. The method of separation by using the crown ether DtBuCH18C6 is proved to be a potential tool for the purification of {sup 89}Sr(II) source produced from yttria target in fast reactors.

Quantum design and synthesis of a boron-oxygen-yttrium phase

International Nuclear Information System (INIS)

Music, Denis; Chirita, Valeriu; Kreissig, Ulrich; Czigany, Zsolt; Schneider, Jochen M.; Helmersson, Ulf

2003-01-01

Ab initio calculations are used to design a crystalline boron-oxygen-yttrium (BOY) phase. The essential constituent is yttrium substituting for oxygen in the boron suboxide structure (BO 0.17 ) with Y/B and O/B ratios of 0.07. The calculations predict that the BOY phase is 0.36 eV/atom more stable than crystalline BO 0.17 and experiments confirm the formation of crystalline thin films. The BOY phase was synthesized with reactive rf magnetron sputtering and identified with x-ray and selected area electron diffraction. Films with Y/B ratios ranging from 0.10 to 0.32, as determined via elastic recoil detection analysis, were grown over a wide range of temperatures (300-600 deg. C) and found to withstand 1000 deg. C

Fabrication and electrical characterization of 15% yttrium-doped barium zirconate-nitrate freeze drying method combined with vacuum heating

International Nuclear Information System (INIS)

Imashuku, Susumu; Uda, Tetsuya; Nose, Yoshitaro; Awakura, Yasuhiro

2011-01-01

Research highlights: → Very fine 15% yttrium-doped barium zirconate powder of particle size about 30 nm was obtained by synthesizing at 500 deg. C in vacuum from powder mixed by the nitrate freeze-drying method. → Large and homogeneous grains of 15% yttrium-doped barium zirconate were easily obtained using the synthesized powder. → Grain boundary resistance was not inversely proportional to the grain size as theoretically expected. → Specific grain boundary conductivity varies with samples because impurities and/or evaporation loss of barium oxide might affect the grain-boundary resistance in 15% yttrium-doped barium zirconate. - Abstract: We applied a nitrate freeze-drying method to obtain a fine synthesized powder of 15% yttrium-doped barium zirconate. Fine 15% yttrium-doped barium zirconate powder of particle size about 30 nm was obtained by synthesizing at 500 deg. C in vacuum from a powder mixed by the nitrate freeze-drying method. However, we could not obtain such fine powder by synthesizing in air. Using the powder synthesized in vacuum, large and homogeneous grains of 15% yttrium-doped barium zirconate were easily obtained after sintering. Then, the bulk and grain boundary resistance were evaluated by AC 2-terminal measurement of sample in the form of bar and pellet and DC 4-terminal measurement of bar-shape sample. The grain boundary resistance was not inversely proportional to the grain size as theoretically expected. We concluded that specific grain boundary conductivity varies with samples. Some impurities, evaporation loss of barium oxide and/or other unexpected reasons might affect the grain boundary resistance in 15% yttrium-doped barium zirconate.

Thermal decomposition of Yttrium(III) isovalerate in argon

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Yue, Zhao; Tang, Xiao

2016-01-01

The thermal behaviour of yttrium(III) isovalerate (Y(C4H9CO2)3) was studied in argon by means of thermogravimetry, differential thermal analysis, FTIR-spectroscopy, hot-stage optical microscopy and X-ray diffraction with a laboratory Cu-tube source as well as with a synchrotron radiation source...

X-ray tube targets

International Nuclear Information System (INIS)

Hirsch, H.H.

1980-01-01

In rotary targets for X-ray tubes warping is a problem which causes X-ray deficiency. A rotary target is described in which warping is reduced by using alloys of molybdenum with 0.05 to 10% iron, silicon, cobalt, tantalum, niobium, hafnium, stable metal oxide or mixture thereof. Suitable mixtures are 0.5 to 10% of tantalum, niobium or hafnium with from 0.5 to 5% yttrium oxide, or 0.05 to 0.3% of cobalt or silicon. Optionally 0.1 to 5% by weight of additional material may be alloyed with the molybdenum, such as tantalum or hafnium carbides. (author)

The effect of yttrium substitution on the magnetic properties of magnetite nanoparticles

International Nuclear Information System (INIS)

Mozaffari, M.; Amighian, J.; Tavakoli, R.

2015-01-01

Superparamagnetic Y-substituted magnetite (Y x Fe 3–x O 4 ,with x=0.00, 0.10, 0.15, 0.20 and 0.40) nanoparticles were synthesized via hydrothermal reduction route in the presence of citric acid. The synthesized nanoparticles were characterized by X-ray diffraction (XRD) analysis, Fourier transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM), vibrating sample magnetometry (VSM) and gradient field thermomagnetic measurement. The results showed that a minimum amount of citric acid is required to obtain single phase Y-substituted magnetite nanoparticles. Citric acid acts as a modulator and reducing agent in the formation of spinel structure and controls nanoparticle size and crystallinity. Mean crystallite sizes of the single-phase powders were estimated by Williamson–Hall method. Curie temperature measurement of the samples shows that as yttrium content increases, the Curie temperature decreases. Magnetic measurements show that the saturation magnetization of the samples decreases as x increases up to 0.15 and then increases to x=0.20 and finally decreases again for x=0.40. - Highlights: • Single phase yttrium substituted magnetite nanoparticles were synthesized by hydrothermal-reduction route. • Citric acid plays a key role in reduction of Fe 3+ to Fe 2+ , which is necessary for the formation of magnetite phase. • It is possible to substitute yttrium ions for iron ones as high as x=0.4 by hydrothermal reduction route. • Pure magnetite nanoparticles prepared by this route has a high saturation magnetization. • Yttrium substituted magnetite nanoparticles are superparamagnet at room temperature

Tribological effects of yttrium and nitrogen ion implantation on a precipitation hardening stainless steel

International Nuclear Information System (INIS)

Alonso, F.; Arizaga, A.; Garcia, A.; Onate, J.I.

1994-01-01

Yttrium, nitrogen and combined yttrium and nitrogen implantations have been carried out on an ASTM A286 precipitation hardening iron base alloy to evaluate the benefits in their tribological behaviour. Microindentation tests have shown a significant 20%-60% increment in hardness on the nitrogen implanted material, with a limited improvement in elastic recovery of the indentation. An abrasive test on the same material has also produced a 50% reduction in scratch depth. Y + and Y + +N + implantations also hardened the material but to a lesser extent. Reciprocating ball on disk friction and wear testing at 400 C resulted in very severe damage in all cases. X-ray photoelectron spectroscopy analyses combined with Ar sputtering have disclosed that nitrogen is mainly in a nitrided form, yttrium remains oxidized at the surface, below which there is an apparent increase in the metallic bond. ((orig.))

Quantitative description of yttrium aluminate ceramic composition by means of Er+3 microluminescence spectrum

Science.gov (United States)

Videla, F. A.; Tejerina, M. R.; Moreira-Osorio, L.; Conconi, M. S.; Orzi, D. J. O.; Flores, T.; Ponce, L. V.; Bilmes, G. M.; Torchia, G. A.

2018-05-01

The composition of erbium-doped yttrium aluminate ceramics was analyzed by means of confocal luminescence spectroscopy, EDX, and X-ray diffraction. A well-defined linear correlation was found between a proposed estimator computed from the luminescence spectrum and the proportion of ceramic phases coexisting in different samples. This result shows the feasibility of using erbium luminescence spectroscopy to perform a quantitative determination of different phases of yttrium aluminates within a micrometric region in nanograined ceramics.

Preparation of polycrystalline lithium-yttrium fluoride for subsequent mono crystallization

International Nuclear Information System (INIS)

Kowalczyk, E.; Radomski, J.; Diduszko, R.; Iwanejko, J.; Kowalczyk, Z.; Grasza, K.

1994-01-01

High purity lithium-yttrium (YLF) doped with rare earth elements (Nd, Pr, Ho or Tm) was obtained in a two-stage synthesis consisting of (1) reaction of ammonium fluoride with a mixture of lithium carbonate, yttrium oxide, and oxides of lanthanides, and (2) heating of the obtained reaction products at a temperature of about 700 C in an inert gas atmosphere. The phase and chemical purities of the obtained materials were characterized by X-ray diffraction and mass spectrometry techniques. Single crystal growth tests were carried out by means of the Bridgman method. The results showed that the proposed method for manufacture of polycrystalline YLF doped with rare earth elements is appropriate in principle but some parameters of the preparation process are to be more strictly defined. (author). 9 refs, 4 figs, 1 tab

Preparation of polycrystalline lithium-yttrium fluoride for subsequent mono crystallization

Energy Technology Data Exchange (ETDEWEB)

Kowalczyk, E.; Radomski, J.; Diduszko, R.; Iwanejko, J. [Institute of Vacuum Technology, Warsaw (Poland); Kowalczyk, Z. [Warsaw Univ. (Poland); Grasza, K. [Polska Akademia Nauk, Warsaw (Poland). Inst. Fizyki

1994-12-31

High purity lithium-yttrium (YLF) doped with rare earth elements (Nd, Pr, Ho or Tm) was obtained in a two-stage synthesis consisting of (1) reaction of ammonium fluoride with a mixture of lithium carbonate, yttrium oxide, and oxides of lanthanides, and (2) heating of the obtained reaction products at a temperature of about 700 C in an inert gas atmosphere. The phase and chemical purities of the obtained materials were characterized by X-ray diffraction and mass spectrometry techniques. Single crystal growth tests were carried out by means of the Bridgman method. The results showed that the proposed method for manufacture of polycrystalline YLF doped with rare earth elements is appropriate in principle but some parameters of the preparation process are to be more strictly defined. (author). 9 refs, 4 figs, 1 tab.

Hydrothermal synthesis, crystal structures and photoluminescence properties of mixed europium–yttrium organic frameworks

International Nuclear Information System (INIS)

Han Yinfeng; Fu Lianshe; Mafra, Luís; Shi, Fa-Nian

2012-01-01

Three mixed europium–yttrium organic frameworks: Eu 2−x Y x (Mel)(H 2 O) 6 (Mel=mellitic acid or benzene-1,2,3,4,5,6-hexacarboxylic acid, x=0.38 1, 0.74 2, and 0.86 3) have been synthesized and characterized. All the compounds contain a 3-D net with (4, 8)-flu topology. The study indicates that the photoluminescence properties are effectively affected by the different ratios of europium and yttrium ions, the quantum efficiency is increased and the Eu 3+ lifetime becomes longer in these MOFs than those of the Eu analog. - Graphical abstract: Three mixed europium and yttrium organic frameworks: Eu 2−x Y x (Mel)(H 2 O) 6 (Mel=mellitic acid) have been synthesized and characterized. All the compounds contain a 3-D net with (4, 8)-flu topology. The study indicates that the photoluminescence properties are effectively affected by the different ratios of europium and yttrium ions, the quantum efficiency is increased and the Eu 3+ lifetime becomes longer in these MOFs than those of the Eu analog. Highlights: ► Three (4, 8)-flu topological mixed Eu and Y MOFs were synthesized under mild conditions. ► Metal ratios were refined by the single crystal data consistent with the EDS analysis. ► Mixed Eu and Y MOFs show longer lifetime and higher quantum efficiency than the Eu analog. ► Adding inert lanthanide into luminescent MOFs enlarges the field of luminescent MOFs.

Thermal decomposition of yttrium(III) hexanoate in argon

DEFF Research Database (Denmark)

Grivel, Jean-Claude; Suarez Guevara, Maria Josefina; Attique, Fahmida

2015-01-01

The thermal decomposition of yttrium(III) hexanoate (Y(C5H11CO2)3)·xH2O in argon was studied by means of thermogravimetry, differential thermal analysis, IR-spectroscopy, X-ray diffraction at a laboratory Cu-tube source and in-situ experiments at a synchrotron radiation source as well as hot...

Yttrium Nitrate mediated Nitration of Phenols at room temperature in ...

Indian Academy of Sciences (India)

The described method is selective for phenols. ... the significant cause of post translational modification that can ... decades, significant attention was paid on nitration of phenols to .... Progress of the reaction can be noted visually. Yttrium.

Yttrium 3-(4-nitrophenyl)-2-propenoate used as inhibitor against copper alloy corrosion in 0.1 M NaCl solution

International Nuclear Information System (INIS)

Nam, Nguyen Dang; Thang, Vo Quoc; Hoai, Nguyen To; Hien, Pham Van

2016-01-01

Highlights: • Yttrium 3-(4-nitrophenyl)-2-propenoate has been studied as an effective corrosion inhibitor for copper. • A high inhibition performance is attributed to the forming protective inhibiting deposits. • Yttrium 3-(4-nitrophenyl)-2-propenoate mitigates corrosion by promoting random distribution of minor anodes. - Abstract: Yttrium 3-(4-nitrophenyl)-2-propenoate has been studied as an effective corrosion inhibitor for copper alloy in 0.1 M chloride solution. The results show that the surface of copper alloy coupons exposed to solutions containing 0.45 mM yttrium 3-(4-nitrophenyl)-2-propenoate had no signs of corrosion attack due to protective film formation, whereas the surface of copper alloy coupons exposed to non-inhibitor and lower concentrations of yttrium 3-(4-nitrophenyl)-2-propenoate containing solutions were severely corroded. A high inhibition performance is attributed to the forming protective inhibiting deposits that slow down the electrochemical corrosion reactions and mitigate corrosion by promoting random distribution of minor anodes.

Hydrogen sensor based on palladium-yttrium alloy nanosheet

Energy Technology Data Exchange (ETDEWEB)

Wang, Boyi [Queensland Micro- and Nanotechnology Centre, Griffith University, Nathan, QLD 4111 (Australia); Zhu, Yong, E-mail: y.zhu@griffith.edu.au [Queensland Micro- and Nanotechnology Centre, Griffith University, Nathan, QLD 4111 (Australia); Chen, Youping; Song, Han; Huang, Pengcheng [School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, 430074 (China); Dao, Dzung Viet [Queensland Micro- and Nanotechnology Centre, Griffith University, Nathan, QLD 4111 (Australia)

2017-06-15

This paper presents a hydrogen sensor based on palladium-yttrium (Pd-Y) alloy nanosheet. Zigzag-shaped Pd-Y nanosheet with a thickness of 19.3 nm was deposited on a quartz substrate by using an ultrahigh-vacuum magnetron sputtering system and shadow mask. The atomic ratio of palladium to yttrium in the nanosheet was 0.92/0.08. The fabrication process was simple and low-cost, and the sensor can be mass-produced. The experimental results show the sensor has a superior sensitivity, reversibility, and reproducibility. The resistive-based hydrogen detection mechanism in this research is much simpler and more compact compared to the optical-based detection method. - Highlights: • Pd-Y sensing element was fabricated using a magnetron sputtering system and shadow mask. • The Pd-Y compound consisted of 92% Pd and 8% Y. • The fabrication process was simple, low-cost, and mass-production compatible. • The sensor showed superior sensitivity, reversibility, and reproducibility to hydrogen gas. • The device is more compact than the optical-based counterpart.

Hydrogen sensor based on palladium-yttrium alloy nanosheet

International Nuclear Information System (INIS)

Wang, Boyi; Zhu, Yong; Chen, Youping; Song, Han; Huang, Pengcheng; Dao, Dzung Viet

2017-01-01

This paper presents a hydrogen sensor based on palladium-yttrium (Pd-Y) alloy nanosheet. Zigzag-shaped Pd-Y nanosheet with a thickness of 19.3 nm was deposited on a quartz substrate by using an ultrahigh-vacuum magnetron sputtering system and shadow mask. The atomic ratio of palladium to yttrium in the nanosheet was 0.92/0.08. The fabrication process was simple and low-cost, and the sensor can be mass-produced. The experimental results show the sensor has a superior sensitivity, reversibility, and reproducibility. The resistive-based hydrogen detection mechanism in this research is much simpler and more compact compared to the optical-based detection method. - Highlights: • Pd-Y sensing element was fabricated using a magnetron sputtering system and shadow mask. • The Pd-Y compound consisted of 92% Pd and 8% Y. • The fabrication process was simple, low-cost, and mass-production compatible. • The sensor showed superior sensitivity, reversibility, and reproducibility to hydrogen gas. • The device is more compact than the optical-based counterpart.

Temporary Arterial Balloon Occlusion as an Adjunct to Yttrium-90 Radioembolization

Energy Technology Data Exchange (ETDEWEB)

Hagspiel, Klaus D., E-mail: kdh2n@virginia.edu [University of Virginia Health System, Department of Radiology and Medical Imaging (United States); Nambiar, Ashwin, E-mail: uvashwin@gmail.com [SUNY Downstate Medical Center, Department of Radiology (United States); Hagspiel, Lauren M., E-mail: lmh4gg@virginia.edu [University of Virginia, College of Arts and Sciences (United States); Ahmad, Ehab Ali, E-mail: ehabradiodiagnosis@yahoo.com [Minia University, Department of Radiology (Egypt); Bozlar, Ugur, E-mail: ubozlar@yahoo.com [Gulhane Military Medical Academy, Department of Radiology (Turkey)

2013-06-15

Purpose. This study was designed to describe the technique of arterial occlusion using a temporary occlusion balloon system as an alternative to coil occlusion during Yttrium-90 radioembolization of hepatic tumors. Methods. Review of charts, angiography, and follow-up imaging studies of consecutive patients undergoing oncological embolization procedures in which a HyperForm system (ev3 Neurovascular, Irvine, CA) was used. Intraprocedural target vessel occlusion and patency of the target vessel on follow-up were recorded. Clinical data and Bremsstrahlung scans were reviewed for evidence of nontarget embolization. Results. Four radioembolization procedures were performed in three patients (all female, age 48-54 (mean 52) years). Five arteries were temporarily occluded (three gastroduodenal arteries, one right gastric artery, and one cystic artery). All radioembolization procedures were successfully completed. Follow-up imaging (either digital subtraction angiography (DSA) or computed tomography angiography (CTA)) was available for all patients between 28-454 (mean 183) days following the procedure, demonstrating all five vessels to be patent. No clinical or imaging evidence for nontarget embolization was found. Conclusions. Temporary balloon occlusion of small and medium-sized arteries during radioembolization allows safe therapy with preserved postprocedural vessel patency on early and midterm follow-up.

Inhibition of Human Cytomegalovirus pUL89 Terminase Subunit Blocks Virus Replication and Genome Cleavage.

Science.gov (United States)

Wang, Yan; Mao, Lili; Kankanala, Jayakanth; Wang, Zhengqiang; Geraghty, Robert J

2017-02-01

The human cytomegalovirus terminase complex cleaves concatemeric genomic DNA into unit lengths during genome packaging and particle assembly. This process is an attractive drug target because cleavage of concatemeric DNA is not required in mammalian cell DNA replication, indicating that drugs targeting the terminase complex could be safe and selective. One component of the human cytomegalovirus terminase complex, pUL89, provides the endonucleolytic activity for genome cleavage, and the domain responsible is reported to have an RNase H-like fold. We hypothesize that the pUL89 endonuclease activity is inhibited by known RNase H inhibitors. Using a novel enzyme-linked immunosorbent assay (ELISA) format as a screening assay, we found that a hydroxypyridonecarboxylic acid compound, previously reported to be an inhibitor of human immunodeficiency virus RNase H, inhibited pUL89 endonuclease activity at low-micromolar concentrations. Further characterization revealed that this pUL89 endonuclease inhibitor blocked human cytomegalovirus replication at a relatively late time point, similarly to other reported terminase complex inhibitors. Importantly, this inhibitor also prevented the cleavage of viral genomic DNA in infected cells. Taken together, these results substantiate our pharmacophore hypothesis and validate our ligand-based approach toward identifying novel inhibitors of pUL89 endonuclease. Human cytomegalovirus infection in individuals lacking a fully functioning immune system, such as newborns and transplant patients, can have severe and debilitating consequences. The U.S. Food and Drug Administration-approved anti-human cytomegalovirus drugs mainly target the viral polymerase, and resistance to these drugs has appeared. Therefore, anti-human cytomegalovirus drugs from novel targets are needed for use instead of, or in combination with, current polymerase inhibitors. pUL89 is a viral ATPase and endonuclease and is an attractive target for anti-human cytomegalovirus

Lack of rise in serum prolactin following yttrium-90 interstitial irradiation for acromegaly

International Nuclear Information System (INIS)

Clark, A.J.L.; Chahal, P.; Mashiter, K.; Joplin, G.F.

1983-01-01

The authors have investigated the possibility that the increase in serum PRL levels observed in patients with acromegaly treated with external irradiation could be due to damage to the hypothalamus or portal vessels, by comparing the effects of yttrium-90 interstitial irradiation, which is highly localised and does not normally extend to the hypothalamus, in a similar series of patients. These results are consistent with the hypothesis; a less likely explanation is that an overgrowth of radio-resistant PRL-secreting tumour cells is occurring after external irradiation, but not after yttrium-90 implantation. (author)

Lack of rise in serum prolactin following yttrium-90 interstitial irradiation for acromegaly

Energy Technology Data Exchange (ETDEWEB)

Clark, A.J.L.; Chahal, P.; Mashiter, K.; Joplin, G.F. (Royal Postgraduate Medical School, London (UK))

1983-11-01

The authors have investigated the possibility that the increase in serum PRL levels observed in patients with acromegaly treated with external irradiation could be due to damage to the hypothalamus or portal vessels, by comparing the effects of yttrium-90 interstitial irradiation, which is highly localised and does not normally extend to the hypothalamus, in a similar series of patients. These results are consistent with the hypothesis; a less likely explanation is that an overgrowth of radio-resistant PRL-secreting tumour cells is occurring after external irradiation, but not after yttrium-90 implantation.

Polymorphism and electrical behaviour of yttrium thin films

International Nuclear Information System (INIS)

Kaul, U.K.; Srivastava, O.N.

1978-01-01

It appears that the thickness-resistivity behaviour of yttrium embodying a thickness-dependent polymorphic phase transition can be explained in terms of surface scattering by taking into account the effect of the change in phase. It is interesting to note that, as a result of the polymorphic transition, the resistivity-thickness curve has an unusual shape. (Auth.)

Radiation protection data sheets for the use of Strontium 90-Yttrium 90 in unsealed sources

International Nuclear Information System (INIS)

Anon.

1993-01-01

This radiation protection data sheet is intended for supervisors and staff in the different medical, hospital, pharmaceutical, university and industrial laboratories and departments where Strontium 90-Yttrium 90 is handled, and also for all those involved in risk prevention in this field. It provides essential data on radiation protection measures during the use of Strontium 90-Yttrium 90 in unsealed sources: physical characteristics, risk assessment, administrative procedures, recommendations, regulations and bibliography

Microstructure and defect chemistry of yttrium aluminium garnet ceramics

International Nuclear Information System (INIS)

Schuh, L.H.

1989-01-01

This thesis describes basic aspects concerning the defect chemistry and the microstructure of yttrium aluminium garnet ceramics. The work consists of three parts: a literature study, an experimental part and a section giving computer simulation data of defects. (author). 320 refs.; 68 figs.; 72 schemes; 32 tabs

MCrAlY bond coat with enhanced Yttrium layer

Science.gov (United States)

Jablonski, Paul D; Hawk, Jeffrey A

2015-04-21

One or more embodiments relates to an MCrAlY bond coat comprising an MCrAlY layer in contact with a Y--Al.sub.2O.sub.3 layer. The MCrAlY layer is comprised of a .gamma.-M solid solution, a .beta.-MAl intermetallic phase, and Y-type intermetallics. The Y--Al.sub.2O.sub.3 layer is comprised of Yttrium atoms coordinated with oxygen atoms comprising the Al.sub.2O.sub.3 lattice. Both the MCrAlY layer and the Y--Al.sub.2O.sub.3 layer have a substantial absence of Y--Al oxides, providing advantage in the maintainability of the Yttrium reservoir within the MCrAlY bulk. The MCrAlY bond coat may be fabricated through application of a Y.sub.2O.sub.3 paste to an MCrAlY material, followed by heating in a non-oxidizing environment.

Effect of vanadium and yttrium doping on BSCCO superconductors

International Nuclear Information System (INIS)

Mohamed, S.B.; Halim, S.A.; Azhan, H.; Sidek, H.A.A; Tee, T.W.; Hassan, Z.A.

1999-01-01

The effect of vanadium and yttrium doping on the superconductivity is investigated. The doping was done on the calcium site ranging from x=0.00-0.10. The temperature dependence of electrical resistance and AC susceptibility measurements were made on these samples. The zero resistance for vanadium doped samples varied from 107 K (x = 0.00) to 68.5K (x = 0.10), whereas for yttrium doped samples it varied from 107 K (x = 0.00) to 54K (x 0.10). The volume fraction of the 2223 phase for both dopalit decreases witli increasing doping concentration. The nature of the temperature derivative of the resistance curves indicates the presence of a superconducting transition between grains coupled by weak links. The AC susceptibility data show enrichment of the volume fraction of the low Tc phase at higher compositions. The presence of low Tc phase (∼70 K) is visible in the susceptibility data. X-ray diffraction confirms the presence of mixed phases in the samples. (author)

Yttrium and lanthanides in human lung fluids, probing the exposure to atmospheric fallout

Energy Technology Data Exchange (ETDEWEB)

Censi, P., E-mail: censi@unipa.it [Dipartimento C.F.T.A., Universita di Palermo, Via Archirafi, 36 90123 - Palermo (Italy); I.A.M.C.-CNR - UOS di Capo Granitola, Via faro, 1 - 91026 Torretta Granitola, Campobello di Mazara (TP) (Italy); En.Bio.Tech. - Via Aquileia, 35 90100 Palermo (Italy); Tamburo, E. [Dipartimento C.F.T.A., Universita di Palermo, Via Archirafi, 36 90123 - Palermo (Italy); Speziale, S. [Deutsches GeoForschungsZentrum, Telegrafenberg, Potsdam, 14473 (Germany); Zuddas, P. [Institut Genie de l' Environnement et Ecodeveloppement and Departement Sciences de la Terre, UMR 5125, Universite Claude Bernard Lyon 1, 2 rue R. Dubois, Bat GEODE 69622 Villeurbanne Cedex (France); Randazzo, L.A. [Dipartimento C.F.T.A., Universita di Palermo, Via Archirafi, 36 90123 - Palermo (Italy); I.A.M.C.-CNR - UOS di Capo Granitola, Via faro, 1 - 91026 Torretta Granitola, Campobello di Mazara (TP) (Italy); En.Bio.Tech. - Via Aquileia, 35 90100 Palermo (Italy); Institut Genie de l' Environnement et Ecodeveloppement and Departement Sciences de la Terre, UMR 5125, Universite Claude Bernard Lyon 1, 2 rue R. Dubois, Bat GEODE 69622 Villeurbanne Cedex (France); Punturo, R. [Dipartimento di Scienze Geologiche, Universita di Catania, Corso Italia, 55 - 95129 Catania (Italy); Cuttitta, A. [I.A.M.C.-CNR - UOS di Capo Granitola, Via faro, 1 - 91026 Torretta Granitola, Campobello di Mazara (TP) (Italy); Arico, P. [Dipartimento C.F.T.A., Universita di Palermo, Via Archirafi, 36 90123 - Palermo (Italy)

2011-02-28

Inhalation of airborne particles can produce crystallization of phosphatic microcrysts in intraaveolar areas of lungs, sometimes degenerating into pulmonary fibrosis. Results of this study indicate that these pathologies are induced by interactions between lung fluids and inhaled atmospheric dust in people exposed to volcanic dust ejected from Mount Etna in 2001. Here, the lung solid-liquid interaction is evaluated by the distribution of yttrium and lanthanides (YLn) in fluid bronchoalveolar lavages on selected individuals according the classical geochemical approaches. We found that shale-normalised patterns of yttrium and lanthanides have a 'V shaped' feature corresponding to the depletion of elements from Nd to Tb when compared to the variable enrichments of heavy lanthanides, Y, La and Ce. These features and concurrent thermodynamic simulations suggest that phosphate precipitation can occur in lungs due to interactions between volcanic particles and fluids. We propose that patterns of yttrium and lanthanides can represent a viable explanation of some pathology observed in patients after prolonged exposure to atmospheric fallout and are suitable to become a diagnostic parameter of chemical environmental stresses.

Influence of radiant heating treatments on fusion of high-temperature superconducting yttrium ceramics

International Nuclear Information System (INIS)

Bitenbaev, M.I.; Polyakov, A.I.

1999-01-01

Regardless of the fact that the materials made of HTSC-ceramics are promising, there is no any information about their successful practical application in publications. To our opinion, it is explained by the fact, first of all, that the conservative technologies of the powder metallurgy do not allow producing HTSC systems with excellent operating performance (structure homogeneity, long-term stability of Sc properties and etc.). This report presents outcomes of experiments on fusion of yttrium ceramics containing raw components irradiated by g-rays 60 Co under the temperature exceeding 500 degrees C. HTSC properties of ceramics were studied according to their differential spectra of radio-frequency (RF) field absorption. The RF absorption spectrum of yttrium ceramics samples produced according to conservative technology is sufficiently permitted triplet with the Sc transition temperatures range of 80 K, 90 K, 95 K. Irradiation under the increased temperatures and mechanical limitation allow producing samples of yttrium HTSC-ceramics with sufficient homogeneous structure and superconducting properties that are stable to air conditions for not less than one year

Innovation in metrology: fast automated radiochemical separation and measurement for strontium 89 and 90

Energy Technology Data Exchange (ETDEWEB)

Augeray, C.; Galliez, K.; Mouton, M.; Tarlette, L.; Loyen, J.; Fayolle, C.; Gleizes, M. [Institut de Radioprotection et de Surete Nucleaire - IRSN (France)

2014-07-01

Measuring radioactivity in the food and for radiological monitoring of the environment around Nuclear Facilities or mining sites requires the quantification of the radioactive isotopes present in the different compartments (liquids or solids), especially of the beta emitters. Strontium 89 and 90, both pure beta emitters are radioactive isotopes of interest. Because of their toxicity and the similarity of their chemical and physical behavior with calcium, these elements may be found through the food chain. After the Fukushima accident, the necessity of quantifying quickly radioactive isotopes such as strontium 89 and 90 appeared. The technique we are going to present concerns the determination of the activity concentration of strontium 89 and 90 in water, according to the {sup 89}Sr/{sup 90}Sr ratio. It consists of two stages: the chemical separation by ionic chromatography and the measurement of the activity concentration of strontium 89 and 90 by Cerenkov Effect. The automated separation has been developed and allows isolating the isotopes of strontium in particular the radioactive ones: strontium 89 and 90. The separation can be done within one hour. It was realized from the adaptation of existing analytical chemistry equipments with on-line couplings. The protocol of separation is based on the use of ions exchange columns of Ionic chromatography not as a separation and measurement technique of the cation but only as a separation technique. At the release time of the ion to be quantified, a fraction collector allows its recovery. The test portion is then analyzed with a liquid scintillation counter (LSC). The activity concentration is measured by Cerenkov Effect on a quenched sample. The quenching is realized by applying a thin colored film on the sample vial. This color quench is used to make strontium 90 counts disappear on the LS spectrum. This way, only yttrium 90 ingrowth and strontium 89 decay are measured (E{sup 90}Sr < E{sup 89}Sr < E{sup 90}Y

A new f.c.c. phase in yttrium films

International Nuclear Information System (INIS)

Kaul, V.K.; Srivastava, O.N.

1976-01-01

A new polymorphic phase characterised by a face-centered cubic structure, with lattice parameter 5.83 +- 0.02A, has been identified in thin films of yttrium. Electron diffraction evidence and electrical resistivity measurements have been carried out in order to detect the new f.c.c. phase. (Auth.)

The influence of implanted yttrium on the cyclic oxidation behaviour of 304 stainless steel

Energy Technology Data Exchange (ETDEWEB)

Riffard, F. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France)]. E-mail: riffard@iut.u-clermont1.fr; Buscail, H. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Caudron, E. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Cueff, R. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Issartel, C. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France); Perrier, S. [Laboratoire Vellave sur l' Elaboration et l' Etude des Materiaux (LVEEM), CNRS-EA 3864, Universite Blaise Pascal Clermont-Fd II, 8 rue J.B. Fabre, B. P. 219, 43006 Le Puy-en-Velay (France)

2006-03-15

High-temperature alloys are frequently used in power plants, gasification systems, petrochemical industry, combustion processes and in aerospace applications. Depending on the application, materials are subjected to corrosive atmospheres and thermal cycling. In the present work, thermal cycling was carried out in order to study the influence of implanted yttrium on the oxide scale adherence on 304 steel specimens oxidised in air at 1273 K. In situ X-ray diffraction indicates that the oxides formed at 1273 K are different on blank specimens compared to implanted specimens. Glancing angle XRD allows to analyse the oxide scale composition after cooling to room temperature. Experimental results show that yttrium implantation at a nominal dose of 10{sup 17} ions cm{sup -2} does not improve significantly the cyclic oxidation behaviour of the austenitic AISI 304 steel. However, it appears that yttrium implantation remarkably enhance the oxidation resistance during isothermal oxidation. It reduces the transient oxidation stage and the parabolic oxidation rate constant by one order of magnitude.

Yttrium-enriched YBa₂Cu₃O_x thin films for coated conductors fabricated by pulsed laser deposition

DEFF Research Database (Denmark)

Khoryushin, Alexey V.; Mozhaev, Peter B.; Mozhaeva, Julia E.

2013-01-01

The effects of excess yttria on the structural and electrical properties of the YBa2Cu3Ox (YBCO) thin films are studied. The films were deposited on (LaAlO3)0.3–(Sr2AlTaO8)0.7 substrates by pulsed laser ablation from targets with different elemental composition. An increase of yttrium content of ...

Separation coefficients of liquid-vapor in systems formed by yttrium chloride with some impurities

International Nuclear Information System (INIS)

Volkov, V.T.; Nikiforova, T.V.; Nisel'son, L.A.; Telegin, G.F.

1990-01-01

Using equilibrium Rayleigh distillation in the 800-950 deg C temperature range, separation coefficients of liquid-vapor for systems, formed by yttrium chloride with Co, Cr, Ni, Mn, Fe, Cu, Na, K, Mg, Ca, Li impurities are determined. The impurity concentration lies within 0.02-0.4 mass. % limits of each impurity, and total impurity concentration does not exceed 1 mass. %. The tested impurities, except for calcium, are more volatile than the base, yttrium trichloride. In most systems negative deviation from the Raoult's law is observed

Purification in the interaction between yttria mould and Nb-silicide-based alloy during directional solidification: A novel effect of yttrium

International Nuclear Information System (INIS)

Ma, Limin; Tang, Xiaoxia; Wang, Bin; Jia, Lina; Yuan, Sainan; Zhang, Hu

2012-01-01

Nb-silicide-based alloys were directionally solidified in yttria moulds. As a result of thermal dissociation of yttria, the alloys were slightly contaminated with oxygen, which caused a competitive oxidation between yttrium and hafnium. The addition of 0.15 at.% yttrium reduced the oxygen increment by 42%, because the buoyant inclusions concentrated around the top surface. The yttrium addition caused a significant purification of the interaction between the yttria mould and the Nb-silicide-based alloys during the directional solidification.

Microstructural and mechanical properties of gravity-die-cast A356 alloy inoculated with yttrium and Al-Ti-B grain refiner simultaneously

Directory of Open Access Journals (Sweden)

Y.P. Lim

2011-10-01

Full Text Available In the present work, the effect of inoculating yttrium and Al-5Ti-1B simultaneously on A356 aluminum alloy has been studied. Gravity die casting process is used to cast the ASTM tensile test specimens for analysis. In each experiment, the Ti and B contents were maintained constantly at 0.1 and 0.02 wt% respectively. The addition of yttrium was manipulated at the amount of 0, 0.1, 0.2, 0.3, 0.4 and 0.5 wt%. Microstructural characterization of the as-cast A356 alloy was investigated by means of optical microscope and its phases are detected by XRD. The mechanical properties tested are tensile strength and hardness. The inoculation of yttrium was found to enhance the grain refinement effect of Al-5Ti-1B grain refiner and improve the mechanical properties. The optimal weight percentage of yttrium was found to be 0.3. The grain refining efficiency of combining yttrium and Al-5Ti-1B on A356 aluminum alloy was mainly attributed to the heterogeneous nucleation of TiB2 and TiAl3 particles which were dispersed more evenly in the presence of yttrium and the grain growth restriction effected by the accumulation of Al-Y compound at grain boundaries.

Fabrication of dense yttrium oxyfluoride ceramics by hot pressing and their mechanical, thermal, and electrical properties

Science.gov (United States)

Tahara, Ryuki; Tsunoura, Toru; Yoshida, Katsumi; Yano, Toyohiko; Kishi, Yukio

2018-06-01

Excellent corrosion-resistant materials have been strongly required to reduce particle contamination during the plasma process in semiconductor production. Yttrium oxyfluoride can be a candidate as highly corrosion-resistant material. In this study, three types of dense yttrium oxyfluoride ceramics with different oxygen contents, namely, YOF, Y5O4F7 and Y5O4F7 + YF3, were fabricated by hot pressing, and their mechanical, thermal, and electrical properties were evaluated. Y5O4F7 ceramics showed an excellent thermal stability up to 800 °C, a low loss factor, and volume resistivity comparable to conventional plasma-resistant oxides, such as Y2O3. From these results, yttrium oxyfluoride ceramics are strongly suggested to be used as electrostatic chucks in semiconductor production.

Physicochemical analysis of cryocrystallization processes of aqueous solutions of yttrium, barium, copper nitrates and their mixtures

International Nuclear Information System (INIS)

Kulakov, A.B.; Mozhaev, A.P.; Tesker, A.M.; Churagulov, B.R.

1992-01-01

Products of fast hardening of aqueous solutions of different concentration of yttrium, barium copper nitrates and their mixtures including mixture of three nitrates with molar ratio equal to 1:2:3 used for synthesis of YBa 2 Cu 3 O 7-x HTSC by cryochemical technique, in liquid nitrogen, are studied using low-temperature, differential thermal and X-ray phase analyses. Aqueous solutions of barium, copper, yttrium nitrates are shown to belong to three different classes which differ in behaviour at fast cooling and subsequent slow heating. Cryogranulate at YBa 2 Cu 2 O 7-x synthesis using cryochemical technique represents mixture of X-ray amorphous Ba(NO 3 ) 2 , crystalline Cu(NO 3 ) 2 ·6H 2 O and ice, as well as, supercooled aqueous solution of yttrium and copper nitrates

Temperature effect on elastic properties of yttrium ferrite garnet Y3Fe5O12

International Nuclear Information System (INIS)

Burenkov, Yu.A.; Nikanorov, S.P.

2002-01-01

One studied temperature dependence of all independent elastic constants describing comprehensively elastic anisotropy of yttrium ferrite garnet within temperature wide range covering T c . One measured the Young modules for [100] and [110] crystallographic directions and the module of shift for [100] direction of specially pure single crystal of yttrium ferrite garnet within 20-600 deg C temperature range. One analyzed behavior of elastic modules and of elastic anisotropy factor near the critical temperature of magnetic phase transition [ru

Element selective X-ray magnetic circular and linear dichroisms in ferrimagnetic yttrium iron garnet films

Energy Technology Data Exchange (ETDEWEB)

Rogalev, A. [European Synchrotron Radiation Facility (ESRF), B.P. 220, F-38043 Grenoble Cedex (France); Goulon, J. [European Synchrotron Radiation Facility (ESRF), B.P. 220, F-38043 Grenoble Cedex (France)], E-mail: goulon@esrf.fr; Wilhelm, F. [European Synchrotron Radiation Facility (ESRF), B.P. 220, F-38043 Grenoble Cedex (France); Brouder, Ch. [Institut de Mineralogie et de Physique des Milieux Condenses, UMR-CNRS 7590, Universite Paris VI-VII, 4 place Jussieu, F-75252 Paris Cedex 05 (France); Yaresko, A. [Max Planck Institute for Solid State Research, Heisenbergstrasse 1, 70569 Stuttgart (Germany); Ben Youssef, J.; Indenbom, M.V. [Laboratoire de Magnetisme de Bretagne, CNRS FRE 2697, UFR Sciences et Techniques, F-29328 Brest Cedex (France)

2009-12-15

X-ray magnetic circular dichroism (XMCD) was used to probe the existence of induced magnetic moments in yttrium iron garnet (YIG) films in which yttrium is partly substituted with lanthanum, lutetium or bismuth. Spin polarization of the 4d states of yttrium and of the 5d states of lanthanum or lutetium was clearly demonstrated. Angular momentum resolved d-DOS of yttrium and lanthanun was shown to be split by the crystal field, the two resolved substructures having opposite magnetic polarization. The existence of a weak orbital moment involving the 6p states of bismuth was definitely established with the detection of a small XMCD signal at the Bi M{sub 1}-edge. Difference spectra also enhanced the visibility of subtle changes in the Fe K-edge XMCD spectra of YIG and {l_brace}Y, Bi{r_brace}IG films. Weak natural X-ray linear dichroism signatures were systematically observed with all iron garnet films and with a bulk YIG single crystal cut parallel to the (1 1 1) plane: this proved that, at room temperature, the crystal cannot satisfy all requirements of perfect cubic symmetry (space group: Ia3-bar d), crystal distortions preserving at best trigonal symmetry (R3-bar or R3m). For the first time, a very weak X-ray magnetic linear dichroism (XMLD) was also measured in the iron K-edge pre-peak of YIG and revealed the presence of a tiny electric quadrupole moment in the ground-state charge distribution of iron atoms. Band-structure calculations carried out with fully relativistic LMTO-LSDA methods support our interpretation that ferrimagnetically coupled spins at the iron sites induce a spin polarization of the yttrium d-DOS and reproduce the observed crystal field splitting of the XMCD signal.

Element selective X-ray magnetic circular and linear dichroisms in ferrimagnetic yttrium iron garnet films

International Nuclear Information System (INIS)

Rogalev, A.; Goulon, J.; Wilhelm, F.; Brouder, Ch.; Yaresko, A.; Ben Youssef, J.; Indenbom, M.V.

2009-01-01

X-ray magnetic circular dichroism (XMCD) was used to probe the existence of induced magnetic moments in yttrium iron garnet (YIG) films in which yttrium is partly substituted with lanthanum, lutetium or bismuth. Spin polarization of the 4d states of yttrium and of the 5d states of lanthanum or lutetium was clearly demonstrated. Angular momentum resolved d-DOS of yttrium and lanthanun was shown to be split by the crystal field, the two resolved substructures having opposite magnetic polarization. The existence of a weak orbital moment involving the 6p states of bismuth was definitely established with the detection of a small XMCD signal at the Bi M 1 -edge. Difference spectra also enhanced the visibility of subtle changes in the Fe K-edge XMCD spectra of YIG and {Y, Bi}IG films. Weak natural X-ray linear dichroism signatures were systematically observed with all iron garnet films and with a bulk YIG single crystal cut parallel to the (1 1 1) plane: this proved that, at room temperature, the crystal cannot satisfy all requirements of perfect cubic symmetry (space group: Ia3-bar d), crystal distortions preserving at best trigonal symmetry (R3-bar or R3m). For the first time, a very weak X-ray magnetic linear dichroism (XMLD) was also measured in the iron K-edge pre-peak of YIG and revealed the presence of a tiny electric quadrupole moment in the ground-state charge distribution of iron atoms. Band-structure calculations carried out with fully relativistic LMTO-LSDA methods support our interpretation that ferrimagnetically coupled spins at the iron sites induce a spin polarization of the yttrium d-DOS and reproduce the observed crystal field splitting of the XMCD signal.

Temperature dependence of sound velocity in yttrium ferrite

International Nuclear Information System (INIS)

L'vov, V.A.

1979-01-01

The effect of the phonon-magnon and phonon-phonon interoctions on the temperature dependence of the longitudinal sound velocity in yttrium ferrite is considered. It has been shown that at low temperatures four-particle phonon-magnon processes produce the basic contribution to renormalization of the sound velocity. At higher temperatures the temperature dependence of the sound velocity is mainly defined by phonon-phonon processes

Synthesis and in-depth analysis of highly ordered yttrium doped hydroxyapatite nanorods prepared by hydrothermal method and its mechanical analysis

International Nuclear Information System (INIS)

Nathanael, A. Joseph; Mangalaraj, D.; Hong, S.I.; Masuda, Y.

2011-01-01

In this study, undoped and yttrium (Y) doped nanocrystalline hydroxyapatite crystals were synthesized by the hydrothermal method at 180 °C for 24 h. Highly ordered and oriented hydroxyapatite (HAp) nanorods were prepared by yttrium doping and their nanostructure and physical properties were compared with those of undoped HAp rods. FESEM images showed that the doping with Y ions reduced the diameter (from 25 nm to 15 nm) and increased the length (from 95 nm to 115 nm) of the synthesized rods. The aspect ratio of the undoped and Y-doped nanorods were calculated to be 4.303 (SD = 0.0959) and 7.61 (SD = 0.0355), respectively. Specific surface area (SSA) analysis showed that SSA also increased from 66.74 m 2 /g to 68.57 m 2 /g with the addition of yttrium. Y-doped HAp nanorod reinforced HMWPE composites displayed the better mechanical performance than those reinforced with pure HAp nanorods. The possible strengthening of nanorods and the increase of SSA due to the reduction in the size of nanorods in the presence of yttrium may have contributed to the strengthening of Y-doped HAp/HMWPE composites. - Graphical Abstract: Highly ordered and oriented yttrium doped hydroxyapatite (HAp) nanorods were prepared by hydrothermal method. For undoped HAp the average length of the nanorod is 95 nm with mean diameter of 24 nm and for a Y doped nanorod the average length is ∼ 115 nm and the mean diameter is 15 nm. Mechanical analysis was carried out by polymer/nanoparticle composite method. Highlights: ► Yttrium doped hydroxyapatite nanorods were prepared by hydrothermal method. ► The nanorods have highly uniform size distribution. ► Yttrium substitution and nanostructure formation was confirmed by careful analysis. ► Mechanical strength was analyzed by polymer nanoparticle reinforcement method.

Ultrasonic measurements and other allied parameters of yttrium soaps in mixed organic solvents

International Nuclear Information System (INIS)

Mehrotra, K.N.; Tandon, K.

1990-01-01

The ultrasonic measurements of yttrium soaps were made in a mixture of 70 % benzene and 30 % dimethylsulfoxide (ν/ν) to determine the critical micelle concentration, soap-solvent interaction and various acoustic and thermodynamic parameters. The values of the CMC decrease with increasing chainlength of fatty acid constituent of the soap molecule and are in agreement with the values obtained from other micellar properties. The various acoustic parameters (intermolecular freelength, adiabatic compressibility, apparent molar compressibility, specific acoustic impedance, apparent molar volume, molar sound velocity, solvation number, available volume and relative association) for yttrium soaps (myristate, palmitate, stearate and oleate) have been evaluated by ultrasonic velocity measurements. (Authors)

Pemisahan Unsur Samarium dan Yttrium dari Mineral Tanah Jarang dengan Teknik Membran Cair Berpendukung (Supported Liquid Membrane

Directory of Open Access Journals (Sweden)

Amri Amin

2009-06-01

Full Text Available he increasing use of rare earth elements in high technology industries needs to be supported by developmental work for the separation of elements. The research objective is fiercely attracting and challenging considering the similarity of bath physical and chemical properties among these elements. The rate separation of samarium and yttrium elements using supported liquid membrane has been studied. Polytetrafluoroethylene (PTFE with pore size of 0.45 µm has been used as the membrane and di(2-ethylhexyl phosphate (D2EHP in hexane has been used as a carrier and nitric acid solution has been used as receiving phase. Result of experiments showed that the best separation rate of samarium and yttrium elements could be obtained at feeding phase of pH 3.0, di(2-ethylhexyl phosphate (D2EHP concentration of 0.3 M, agitation rate of 700 rpm, agitation time of 2 hours, and nitric acid and its solution concentrations of 1.0 M and 0.1 M, respectively. At this condition, separation rates of samarium and yttrium were 64.4 and 67.6%, respectively.   Keywords: liquid membrane, rare earth elements, samarium, yttrium

The influence of annealing on yttrium oxide thin film deposited by reactive magnetron sputtering: Process and microstructure

Directory of Open Access Journals (Sweden)

Y. Mao

2017-01-01

Full Text Available Yttrium oxide thin films were prepared by reactive magnetron sputtering in different deposition condition with various oxygen flow rates. The annealing influence on the yttrium oxide film microstructure is investigated. The oxygen flow shows a hysteresis behavior on the deposition rate. With a low oxygen flow rate, the so called metallic mode process with a high deposition rate (up to 1.4µm/h was achieved, while with a high oxygen flow rate, the process was considered to be in the poisoned mode with an extremely low deposition rate (around 20nm/h. X-ray diffraction (XRD results show that the yttrium oxide films that were produced in the metallic mode represent a mixture of different crystal structures including the metastable monoclinic phase and the stable cubic phase, while the poisoned mode products show a dominating monoclinic phase. The thin films prepared in metallic mode have relatively dense structures with less porosity. Annealing at 600 °C for 15h, as a structure stabilizing process, caused a phase transformation that changes the metastable monoclinic phase to stable cubic phase for both poisoned mode and metallic mode. The composition of yttrium oxide thin films changed from nonstoichiometric to stoichiometric together with a lattice parameter variation during annealing process. For the metallic mode deposition however, cracks were formed due to the thermal expansion coefficient difference between thin film and the substrate material which was not seen in poisoned mode deposition. The yttrium oxide thin films that deposited in different modes give various application options as a nuclear material.

Cold laser machining of nickel-yttrium stabilised zirconia cermets: Composition dependence

International Nuclear Information System (INIS)

Sola, D.; Gurauskis, J.; Pena, J.I.; Orera, V.M.

2009-01-01

Cold laser micromachining efficiency in nickel-yttrium stabilised zirconia cermets was studied as a function of cermet composition. Nickel oxide-yttrium stabilised zirconia ceramic plates obtained via tape casting technique were machined using 8-25 ns pulses of a Nd: YAG laser at the fixed wavelength of 1.064 μm and a frequency of 1 kHz. The morphology of the holes, etched volume, drill diameter, shape and depth were evaluated as a function of the processing parameters such as pulse irradiance and of the initial composition. The laser drilling mechanism was evaluated in terms of laser-material interaction parameters such as beam absorptivity, material spallation and the impact on the overall process discussed. By varying the nickel oxide content of the composite the optical absorption (-value is greatly modified and significantly affected the drilling efficiency of the green state ceramic substrates and the morphology of the holes. Higher depth values and improved drilled volume upto 0.2 mm 3 per pulse were obtained for substrates with higher optical transparency (lower optical absorption value). In addition, a laser beam self-focussing effect is observed for the compositions with less nickel oxide content. Holes with average diameter from 60 μm to 110 μm and upto 1 mm in depth were drilled with a high rate of 40 ms per hole while the final microstructure of the cermet obtained by reduction of the nickel oxide-yttrium stabilised zirconia composites remained unchanged.

Synthesis of yttrium oxide nanoparticles via a facile microplasma-assisted process

NARCIS (Netherlands)

Lin, Liangliang; Starostin, Sergey A.; Li, Sirui; Khan, Saif A.; Hessel, Volker

2018-01-01

Plasma electrochemistry is an emerging technique for nanomaterial synthesis. The present study reports the preparation of yttrium oxide nanoparticles via a simple, environmentally benign, microplasma-assisted process operated in pin-to-liquid configuration under ambient atmospheric conditions using

Studies on the pressed yttrium oxide-tungsten matrix as a possible dispenser cathode material

International Nuclear Information System (INIS)

Yang, Fan; Wang, Jinshu; Liu, Wei; Liu, Xiang; Zhou, Meiling

2015-01-01

Yttrium oxide was chosen as the secondary emission substance based on calculation results through first principle theory method. A new kind of pressed yttrium oxide-tungsten matrix dispenser cathodes are prepared by a sol–gel method combined with high temperature sintering in dry hydrogen atmosphere. The results show that the growth of the grains is hampered by the pinning effect of Y 2 O 3 distributing uniformly between the tungsten particles, resulting in the formation of small grain size. It is found that Y 2 O 3 improves the secondary electron emission property, i.e., the secondary emission yield increases with the increase of Y 2 O 3 content in the samples. The maximum secondary emission yield δ max of the cathode with 15% amount of Y 2 O 3 can reach 2.92. Furthermore, the cathode shows a certain thermionic emission performance. The zero field emission current density J 0 of 4.18A/cm 2 has reached at 1050 °C b for this kind of cathode after being activated at 1200 °C b , which are much higher than that of rare earth oxide doped molybdenum (REO-Mo) cathode reported in the previous work. - Highlights: • Yttrium oxide was chosen as the secondary emission substance based on first principle calculation result. • A new kind of cathode has been successfully obtained. • Pressed yttrium oxide-tungsten matrix dispenser cathode exhibits good emission properties. • The improvement of the cathode emission can be well explained by the surface analysis results presented in this work

Determination of the emission rate for the 14 MeV neutron generator with the use of radio-yttrium

Directory of Open Access Journals (Sweden)

Laszynska Ewa

2015-06-01

Full Text Available The neutron emission rate is a crucial parameter for most of the radiation sources that emit neutrons. In the case of large fusion devices the determination of this parameter is necessary for a proper assessment of the power release and the prediction for the neutron budget. The 14 MeV neutron generator will be used for calibration of neutron diagnostics at JET and ITER facilities. The stability of the neutron generator working parameters like emission and angular homogeneity affects the accuracy of calibration other neutron diagnostics. The aim of our experiment was to confirm the usefulness of yttrium activation method for monitoring of the neutron generator SODERN Model: GENIE 16. The reaction rate induced by neutrons inside the yttrium sample was indirectly measured by activation of the yttrium sample, and then by means of the γ-spectrometry method. The pre-calibrated HPGe detector was used to determine the yttrium radioactivity. The emissivity of neutron generator calculated on the basis of the measured radioactivity was compared with the value resulting from its electrical settings, and both of these values were found to be consistent. This allowed for a positive verification of the reaction cross section that was used to determine the reaction rate (6.45 × 10−21 reactions per second and the neutron emission rate (1.04 × 108 n·s−1. Our study confirms usefulness of the yttrium activation method for monitoring of the neutron generator.

Study of yttrium 4-nitrocinnamate to promote surface interactions with AS1020 steel

Energy Technology Data Exchange (ETDEWEB)

Hien, P.V. [Department of Chemical Engineering, Bach Khoa University, VNU-HCM, 268 Ly Thuong Kiet Street, District 10, Ho Chi Minh City (Viet Nam); Vu, N.S.H.; Thu, V.T.H. [Faculty of Physics and Engineering Physics, University of Science, 227 Nguyen Van Cu Street, District 5, Ho Chi Minh City (Viet Nam); Somers, A. [Institute for Frontier Materials, Deakin University, Geelong, Victoria 3220 (Australia); Nam, N.D., E-mail: namnd@pvu.edu.vn [PetroVietnam University, 762 Cach Mang Thang Tam Street, Long Toan Ward, Ba Ria City, Ba Ria—Vung Tau Province (Viet Nam)

2017-08-01

Highlights: • Yttrium 4-nitrocinnamate is a new corrosion inhibitor alternative to chromate technologies. • The inhibition performance is increased with increase of the inhibitor concentration. • Yttrium 4-nitrocinnamate mitigates corrosion by promoting random distribution of minor anodes. • Yttrium 4-nitrocinnamate is a good candidate for substitution of chromate inhibitors. - Abstract: Yttrium 4-nitrocinnamate (Y(4-NO{sub 2}Cin){sub 3}) was added to an aqueous chloride solution and studied as a possible corrosion inhibition system. Electrochemical techniques and surface analysis have been powerful tools to better understand the corrosion and inhibition processes of mild steel in 0.01 M NaCl solution. A combination of scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS), Potentiodynamic polarization (PD), electrochemical impedance spectroscopy (EIS) and wire beam electrode (WBE) techniques was found to be useful in the characterization of this system. The result indicated that Y(4-NO{sub 2}Cin){sub 3} is able to effectively inhibit corrosion at a low concentration of 0.45 mM. Surface analysis clearly shows that the surface of steel coupons exposed to Y(4-NO{sub 2}Cin){sub 3} solution remained uniform and smooth, whereas the surface of steel coupons exposed to solution without inhibitor addition was severely corroded. The results suggest that Y(4-NO{sub 2}Cin){sub 3} behaves as a mixed inhibitor and mitigates corrosion by promoting random distribution of minor anodes. These are attributed to the formation of metal species bonding to the 4-nitrocinnamate component and hydrolysis of the Y(4-NO{sub 2}Cin){sub 3} to form oxide/hydroxides as a protective film layer.

First Year Report: Nuclear Reaction Measurements with Radioactive Beams and Targets- Progress in Measurements of the 89Zr (n,xnyp) Reaction Cross Sections

International Nuclear Information System (INIS)

Joseph Cerny; Dennis Moltz; Sylvia La; Ed Morse; Larry Ahle; Lee Bernstein; Ken Moody; Kevin Roberts; Margaret Moody; James Powell; Jim O'Neil; Anthony Belian

2004-01-01

OAK-B135 During the underground nuclear tests in Nevada, some of the most important information was obtained by radiochemical analysis of post-test excavations. By adding small samples of refractory and rare earth elements not commonly present in the surrounding soil to the device, a detailed look could be had of the actual event. In order to properly analyze these data, several hundred cross sections are needed at a neutron energy of 14 MeV (a d-t-burn product). Although it has always been assumed that these calculations are correct, insufficient experimental data exist to corroborate this assumption. The purpose of this experiment is to measure two reaction cross sections, namely the 89 Zr (n, 2n) 88 Zr and 89 Zr (n, np) 88 Y reactions. Although the former reaction has been measured in an unpublished report ( A. A. Delucchi and W. Goishi, LANL Report LA-7841-C (1977) pp. 33-36), we intend to reduce the experimental error in this cross section. The latter cross section has not been measured. This case is much simplified because these reaction products have half-lives ∼100 days compared with ∼3 days for the target nuclide. Therefore the assay can be accomplished long after the target nuclei have decayed away

Elaboration and characterisation of yttrium oxide and hafnium oxide powders by the sol-gel process

International Nuclear Information System (INIS)

Hours, T.

1988-01-01

The two classical sol-gel processes, colloidal and polymeric are studied for the preparation of yttrium oxide and hafnium oxide high performance powders. In the colloidal process, controlled and reproducible conditions for the preparation of yttrium oxide and hafnium oxide sols from salts or alkoxides are developed and the hydrothermal synthesis monodisperse hafnium oxide colloids is studied. The polymeric process is studied with hafnium ethyl-hexylate, hydrolysis kinetics for controlled preparation of sols and gels is investigated. Each step of preparation is detailed and powders obtained are characterized [fr

Optimization Recovery of Yttrium Oxide in Precipitation, Extraction, and Stripping Process

Science.gov (United States)

Perwira, N. I.; Basuki, K. T.; Biyantoro, D.; Effendy, N.

2018-04-01

Yttrium oxide can be used as a dopant control rod of nuclear reactors in YSH material and superconductors. Yttrium oxide is obtained in the Xenotime mineral derived from byproduct of tin mining PT Timah Bangka which contain rare earth elements (REE) dominant Y, Dy, and Gd whose content respectively about 29.53%, 7.76%, and 2.58%. Both usage in the field of nuclear and non-nuclear science and technology is need to pure from the impurities. The presence of impurities in the yttrium oxide may affect the characteristic of the material and the efficiency of its use. Thus it needs to be separated by precipitation and extraction-stripping and calcination in the making of the oxide. However, to obtain higher levels of Yttrium oxide, it is necessary to determine the optimum conditions for its separation. The purpose of this research was to determine the optimum pH of precipitation, determine acid media and concentration optimum in extraction and stripping process and determine the efficiency of the separation of Y from REE concentrate. This research was conducted with pH variation in the precipitation process that pHs were 4 - 8, the difference of acid media for the extraction process, i.e., HNO3, HCl and H2SO4 with each concentration of 0,5 M; 1 M; 1,5 M; and 2 M and for stripping process were HNO3, HCl, and H2SO4 with each concentration of 1 M; 2M; and 3 M. Based on the result, the optimum pH of precipitation process was 6,5, the optimumacid media was HNO3 0,5 M, and for stripping process media was HNO3 3 M. The efficiency of precipitation process at pH 6,5 was 69,53 %, extraction process was 96.39% and stripping process was 4,50%. The separation process from precipitation to extraction had increased the purity and the highest efficiency recovery of Y was in the extraction process and obtained Y2O3 purer compared to the feed with the Y2O3 content of 92.87%.

Electrochemical separation of cerium and yttrium in molten chlorides on liquid-metallic electrodes

International Nuclear Information System (INIS)

Yamshchikov, L.F.; Lebedev, V.A.; Nichkov, I.F.

1978-01-01

An estimating calculation of the coefficients of separation of cerium and yttrium in the process of electrolysis in molten salts on liquid electrodes of aluminium, gallium, indium, lead, tin, antimonium and zinc is carried out. The calculation of the separation coefficients was carried out according to the known values of activation coefficients of cerium and yttrium in fusible metals. The electrolysis was carried out at 973 K in the argon air in the cell with an eutectic mixture of NaCl and KCl as an elactrolyte. It is shown that the salten phase is concentrated by yttrium, and the melallic one- by cerium on all the electrodes. The value of the separation coefficient of Ce and Y is considerably high and continuously increases on the fusible metals in the Zn, In, Ga, Al, Pb, Sn, Sb series. The experimental values of the separation coefficients practically coincide with the theoretically calculated ones, testifying to the possibility of the effective separation of elements even in a single-staged possibility of the effective separation of elements even in a single-staged process. An electrolysis of molten salts is not inferior in its selectivity to the universally recognized methods of the fine purification of substances permitting to separate Ce and Y with the Ksub(sep) approximately equal to 10

Yttrium deposition on mesoporous TiO2: textural design and UV ...

Indian Academy of Sciences (India)

The mesoporous yttrium-doped TiO2 substrates prepared in this research work operate ... bond lengths in the nanoparticles (0.192 and 0.196 nm).18. Additionally ...... Fisicoquímica de Materiales Mesoporosos' (UAM-I CA-31. Fisicoquímica de ...

Preparation of yttrium iron garnet (YIG) by modified domestic iron oxide

International Nuclear Information System (INIS)

Mozaffari, M.; Amighian

2002-01-01

Iron oxide by product of a local steel complex was modified to use for preparation of Yttrium iron garnet (YIG). The improvement was necessary to reduce impurities, especially the Si0 2 and Cl contents, which have deteriorative effects on magnetic properties and equipment used for preparation of the samples. The modified iron oxide was then mixed with Yttrium oxide of Merck Company in appropriate proportion to obtain a stoichiometric single phase YIG, using the conventional ceramic technique. XRD and SEM equipments were used to identify the resulting phases and microstructure respectively. Magnetic parameters were measured by VSM. Curie temperature of the samples was obtained by DTG (M) method. The results were compared with those obtained from samples that made by Merck iron oxide. There are small differences between the results. This was discussed according to extra pores and minute secondary phase in the samples made by domestic iron oxide. (Author)

Studies on the pressed yttrium oxide-tungsten matrix as a possible dispenser cathode material

Energy Technology Data Exchange (ETDEWEB)

Yang, Fan; Wang, Jinshu, E-mail: wangjsh@bjut.edu.cn; Liu, Wei; Liu, Xiang; Zhou, Meiling

2015-01-15

Yttrium oxide was chosen as the secondary emission substance based on calculation results through first principle theory method. A new kind of pressed yttrium oxide-tungsten matrix dispenser cathodes are prepared by a sol–gel method combined with high temperature sintering in dry hydrogen atmosphere. The results show that the growth of the grains is hampered by the pinning effect of Y{sub 2}O{sub 3} distributing uniformly between the tungsten particles, resulting in the formation of small grain size. It is found that Y{sub 2}O{sub 3} improves the secondary electron emission property, i.e., the secondary emission yield increases with the increase of Y{sub 2}O{sub 3} content in the samples. The maximum secondary emission yield δ{sub max} of the cathode with 15% amount of Y{sub 2}O{sub 3} can reach 2.92. Furthermore, the cathode shows a certain thermionic emission performance. The zero field emission current density J{sub 0} of 4.18A/cm{sup 2} has reached at 1050 °C{sub b} for this kind of cathode after being activated at 1200 °C{sub b}, which are much higher than that of rare earth oxide doped molybdenum (REO-Mo) cathode reported in the previous work. - Highlights: • Yttrium oxide was chosen as the secondary emission substance based on first principle calculation result. • A new kind of cathode has been successfully obtained. • Pressed yttrium oxide-tungsten matrix dispenser cathode exhibits good emission properties. • The improvement of the cathode emission can be well explained by the surface analysis results presented in this work.

Yttrium ion implantation on the surface properties of magnesium

International Nuclear Information System (INIS)

Wang, X.M.; Zeng, X.Q.; Wu, G.S.; Yao, S.S.

2006-01-01

Owing to their excellent physical and mechanical properties, magnesium and its alloys are receiving more attention. However, their application has been limited to the high reactivity and the poor corrosion resistance. The aim of the study was to investigate the beneficial effects of ion-implanted yttrium using a MEVVA ion implanter on the surface properties of pure magnesium. Isothermal oxidation tests in pure O 2 at 673 and 773 K up to 90 min indicated that the oxidation resistance of magnesium had been significantly improved. Surface morphology of the oxide scale was analyzed using scanning electron microscope (SEM). Auger electron spectroscopy (AES) and X-ray diffraction (XRD) analyses indicated that the implanted layer was mainly composed of MgO and Y 2 O 3 , and the implanted layer with a duplex structure could decrease the inward diffusion of oxygen and reduce the outward diffusion of Mg 2+ , which led to improving the oxidation resistance of magnesium. Potentiodynamic polarization curves were used to evaluate the corrosion resistance of the implanted magnesium. The results show yttrium implantation could enhance the corrosion resistance of implanted magnesium compared with that of pure magnesium

Lanthanum and yttrium oxysulfides activated by europium: (Ln1-x Eux)2 O2 S - Synthesis and characterization

International Nuclear Information System (INIS)

Luiz, J.M.

1989-01-01

The synthesis of lanthanum and yttrium oxysulfides activated by europium were obtained by thermal decomposition of lanthanum and yttrium oxalates doped with europium, under an argon and sulphur atmosphere. The thermal decomposition of these compounds is studied by differential thermal analysis (DTA). The characterization of these oxysulfides were made by chemical analyses, infrared spectroscopy, X-ray diffraction, scanning electron microscopy and emission spectroscopy. (M.V.M.)

Optical bistability in erbium-doped yttrium aluminum garnet crystal combined with a laser diode.

Science.gov (United States)

Maeda, Y

1994-01-10

Optical bistability was observed in a simple structure of an injection laser diode combined with an erbium-doped yttrium aluminum garnet crystal. Since a hysteresis characteristic exists in the relationship between the wavelength and the injection current of a laser diode, an optical memory function capable of holding the output status is confirmed. In addition, an optical signal inversion was caused by the decrease of transmission of the erbium-doped yttrium aluminum garnet crystal against the red shift (principally mode hopping) of the laser diode. It is suggested that the switching time of this phenomenon is the time necessary for a mode hopping by current injection.

Phase composition of yttrium-doped zirconia ceramics

Energy Technology Data Exchange (ETDEWEB)

Hennig, Christoph; Scheinost, Andreas C. [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Molecular Structures; Weiss, Stephan [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Surface Processes; Ikeda-Ohno, Atsushi [Helmholtz-Zentrum Dresden-Rossendorf e.V., Dresden (Germany). Chemistry of the F-Elements; Gumeniuk, R. [Technische Univ. Bergakademie Freiberg (Germany). Inst. fuer Experimentelle Physik

2017-06-01

Ceramic material might be an alternative to borosilicate glass for the immobilization of nuclear waste. The crystallinity of ceramic material increases the corrosion resistance over several magnitudes in relation to amorphous glasses. The stability of such ceramics depend on several parameters, among them the crystal phase composition. A reliable quantitative phase analysis is necessary to correlate the macroscopic material properties with structure parameters. We performed a feasibility study based on yttrium-doped zirconia ceramics as analogue for trivalent actinides to ascertain that the nanosized crystal phases in zirconia ceramics can be reliably determined.

Nonlinear FMR spectra in yttrium iron garnet

Directory of Open Access Journals (Sweden)

Yu.M. Bunkov, P.M. Vetoshko, I.G. Motygullin, T.R. Safin, M.S. Tagirov, N.A. Tukmakova

2015-12-01

Full Text Available Results of demagnetizing effect studies in yttrium iron garnet Y3Fe5O12 thin films are reported. Experiments were performed on X-Band of electron paramagnetic resonance spectrometer at room temperature. The ferromagnetic resonance (FMR spectra were obtained for one-layer single crystal YIG films for different values of the applied microwave power. Nonlinear FMR spectra transformation by the microwave power increasing in various directions of magnetic field sweep was observed. It is explained by the influence of the demagnetization action of nonequilibrium magnons.

Recurrent thermo-luminescence phenomenon in yttrium-aluminum garnet crystals

International Nuclear Information System (INIS)

Islamov, A.Kh.; Nuritdinov, I.; Esanov, Z.U.; Eshchanov, B.Kh.; Khayitov, I.A.

2014-01-01

Full text : The crystals of yttrium-aluminum garnet Y 2 Al 2 O 1 2 activated by cerium and praseodymium ions by their thermal and chemical durability as well as fast response are perspective scintillation materials. In this work the capture centres formed by action of the ionizing radiation on pure and doped by praseodymium and cerium crystals were investigated. The samples were grown using Chokhralsky method

Comparison by quantitative scanning of the distribution in the body of yttrium-90 and gold-198 after intra-articular injection

International Nuclear Information System (INIS)

Williams, E.D.; Caughey, D.E.; John, M.B.; Hurley, P.J.

1975-01-01

A new radiopharmaceutical, yttrium-90 ferric hydroxide colloid, has been used to treat knee effusion in patients with rheumatoid arthritis. With a view to assessing absorbed radiation dose, a study was initiated to compare its body distribution with that of gold-198, which has also been used for this purpose. The treated knee was in each case scanned immediately after injection using a dual 5-inch detector scanner, and again two, four and seven days later, when the regional lymph nodes and liver were also scanned. Using calibration factors obtained by scanning water phantoms, data from the scans were used to calculate the percentage of the injected radioactivity in each site. Radioactivity in blood and urine was also measured. Ten knees have been treated, each with five mCi yttrium-90, and twelve with 10 mCi gold-198. The treated knee was immobilized, and the patient rested in bed for four days, to minimize loss of radioactivity from the knee. With this procedure, both radionuclides were found to be equally well retained in the knee. However, the lymph node uptake of yttrium was lower than for gold. Yttrium-90 emits only beta radiation, so the gonadal radiation done in patients treated with yttrium-90 is estimated to be much less than in those treated with gold-198. (author)

Graphite furnace atomic absorption spectrometry with a tantalum boat for the determination of yttrium, samarium, and dysprosium in a mish metal

International Nuclear Information System (INIS)

Daidoji, Hidehiro; Tamura, Shohei

1982-01-01

The determination of yttrium, samarium, and dysprodium by means of graphite-furnace atomic absorption spectrometry (AAS) was studied by a tantalum boat inserted into a graphite tube atomizer. These elements could not be determined by the use of a commercial graphite tube, In the atomization from a tantalum boat, better analytical sensitivities and negligible memory effects for these rare earths are obtained. The analytical sensitivities of yttrium, samarium, and dysprodium with the tantalum boat were 0.60 ng, 0.86 ng, and 0.17 ng respectively. This method was applied for the determination of yttrium, samarium, and dysprosium in a mish metal. The measurements were performed with slightly acidified solutions (0.01 mol dm 3 HCI or HNO 3 ). The sensitivities and the precisions for these elements decreased with increasing acid concentration. An enhancement in the sensitivities of yttrium and dysprosium upon the addition of a large excess of lanthanum, neodymium, and praseodymium salts were observed. The yttrium, samarium, and dysprosium in a mish metal were determined with both analytical curves of standard solutions containing an excess of lanthanum, cerium, and neodymium ions and of the standard addition. The precisions for this work were in the 3 - 9.3% range. (author)

Standardized methods for the production of high specific-activity zirconium-89

Science.gov (United States)

Holland, Jason P.; Sheh, Yiauchung; Lewis, Jason S.

2009-01-01

Zirconium-89 is an attractive metallo-radionuclide for use in immunoPET due to the favorable decay characteristics. Standardized methods for the routine production and isolation of high purity and high specific-activity 89Zr using a small cyclotron are reported. Optimized cyclotron conditions reveal high average yields of 1.52 ± 0.11 mCi/μA·h at a proton beam energy of 15 MeV and current of 15 μA using a solid, commercially available 89Y-foil target (0.1 mm, 100% natural abundance). 89Zr was isolated in high radionuclidic and radiochemical purity (>99.99%) as [89Zr]Zr-oxalate by using a solid-phase hydroxamate resin with >99.5% recovery of the radioactivity. The effective specific-activity of 89Zr was found to be in the range 5.28 – 13.43 mCi/μg (470 – 1195 Ci/mmol) of zirconium. New methods for the facile production of [89Zr]Zr-chloride are reported. Radiolabeling studies using the trihydroxamate ligand desferrioxamine B (DFO) gave 100% radiochemical yields in 7 days. Small-animal PET imaging studies have demonstrated that free 89Zr(IV) ions administered as [89Zr]Zr-chloride accumulate in the liver whilst [89Zr]Zr-DFO is excreted rapidly via the kidneys within <20 min. These results have important implication for the analysis of immunoPET imaging of 89Zr-labeled monoclonal antibodies. The detailed methods described can be easily translated to other radiochemistry facilities and will facilitate the use of 89Zr in both basic science and clinical investigations. PMID:19720285

An ICP AES method for determination of dysprosium and terbium in high purity yttrium oxide

International Nuclear Information System (INIS)

Rupawate, V.H.; Hareendran, K.N.; Roy, S.B.

2011-01-01

High purity yttrium finds interesting application in astronavigation, luminescence, nuclear energy and metallurgical industries. Most of these applications require yttrium oxide of highest purity. Consequently there is a need for production of high purity yttrium oxide. Separation and purification of yttrium from other rare earths is a challenging task due to their close chemical properties. Liquid-liquid extraction and ion exchange have been widely used in the production of yttrium oxide of highest purity. Determination of impurities, especially other rare earths, in ppm level is required for process development and chemical characterization of the high purity Y 2 O 3 . Many methods have been described in literature. However since the advent of ICP AES much work in this area has been carried out by this technique. This paper describes the work done for determination of dysprosium (Dy) and terbium (Tb) in yttrium oxide using a high resolution sequential ICP AES. Emission spectra of rare earth elements are very complex and due to this complexity it is important to select spectral interference free analyte lines for determination of rare earths in rare earth matrix. For the determination of Dy and Tb in Y 2 O 3 , sensitive lines of Dy and Tb are selected from the instrument wavelength table and spectral interference free emission lines for the determination is selected by scanning around the selected wavelengths using 5 g/L Y solution and 5 mg/L standard solutions of Dy and Tb prepared in 4% nitric acid. It is found 353.170 nm line of Dy and 350.917 nm line Tb is suitable for quantitative determination. The signal to background ratio increases with increase in matrix concentration, i.e. from 1 to 5 mg/L. The optimum forward power is determined and it is found to be 1100W for Dy and 1000W for Tb. The instrument is calibrated using matrix matched standards containing 5g/L of Y matrix. Samples are dissolved in nitric acid and Y concentration is maintained at 5g/L. Two

Nuclear magnetic resonance of iron-57 nuclei in local fields in yttrium and iron garnets; Resonance magnetique nucleaire des noyaux du fer 57 dans les champs locaux du grenat d'yttrium et de fer

Energy Technology Data Exchange (ETDEWEB)

Robert, C. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1961-07-01

We have demonstrated the nuclear resonance of {sup 57}Fe nuclei in the local field of each of the two magnetic sub-lattices of yttrium and iron garnets. The resonance frequencies and the relaxation times have been measured as a function of the temperature. (author) [French] Nous avons mis en evidence la resonance nucleaire des noyaux de {sup 57}Fe dans le champ local de chacun des deux sous-reseaux magnetiques du grenat d'yttrium et de fer. Les frequences de resonances et les temps de relaxation ont ete mesures en fonction de la temperature. (auteur)

High-pressure structural study of yttrium monochalcogenides from experiment and theory

DEFF Research Database (Denmark)

Vaitheeswaran, G.; Kanchana, V.; Svane, A.

2011-01-01

High-pressure powder x-ray diffraction experiments using synchrotron radiation are performed on the yttrium monochalcogenides YS, YSe, and YTe up to a maximum pressure of 23 GPa. The ambient NaCl structure is stable throughout the pressure range covered. The bulk moduli are determined to be 93, 82...

Separation and purification of gadolinium and others rare earths, and yttrium

International Nuclear Information System (INIS)

Awwal, M.A.; Filgueiras, S.A.C.

1988-01-01

The experimental works in laboratories for developing a solvent extraction process with the purpose of gadolinium separation and purification, and secondarily samarium, europium, lanthanum and yttrium are described. Using as solvent di-2-ethylhexylphosphoric acid (DEHPA) a preliminary flow chart for separation for these elements are developed. (author)

Knee arthroscopy after yttrium or osmic acid injection

International Nuclear Information System (INIS)

Guaydier-Souquieres, C.; Beguin, J.; Ollivier, D.; Loyau, G.

1989-01-01

This study presents the macroscopic and histologic results of 35 knee arthroscopies performed on patients with rheumatoid arthritis, some months after an yttrium or osmic acid intraarticular injection. The procedure was most often performed after a failure of the injection or a relapse of synovitis. Arthroscopy provides an understanding of the cause of synoviorthesis failure--insufficient action of the product on the synovitis or its poor diffusion, fibri-nonecrotic deposits, or cartilaginous lesions--and may be used both diagnostically and therapeutically

Radiolabeling Of Albumin Particles With Yttrium-90

International Nuclear Information System (INIS)

Nguyen Thi Thu; Nguyen Thi Khanh Giang; Bui Van Cuong, Vo Thi Cam Hoa

2011-01-01

This paper presents the process of the radiolabeling of microaggregated albumin particles with radionuclide Yttrium-90 using the directed method. The albumin microsphere kit was prepared in sodium phosphate buffer. The original solution includes 2 mg albumin particle and 0.5 mg stannous chloride dihydrate. The albumin particles size was ranged from 5 ?m to 30 ?m. The mixture was washed three times with phosphate buffer saline, pH 7.2 by centrifugation and suspended in 0.5 M sodium acetate buffer, pH 6. Yttrium - 90 in 1.0 M acetic acid was collected from 90 Sr/ 90 Y generator. The labeling of the particles with Y-90 (185 MBq) was performed at pH 5.5 in acetate buffer with agitating for 60 min at room temperature. The labeled albumin suspensions were centrifuged at 3000 rpm for 15 min. Labeling yields was calculated using centrifugation, filtration and compared with paper chromatography, which is developed in the Tris Acetic EDTA. In this system, the unbound of Y-90 migrates to an R f of 0.9-1.0 and the radiolabeled albumin particles remains at the point of origin (R f = 0). The size of 90 Y-albumin particles was compared with the albumin particles in the original solution to be sure that they did not change during the labeling treatment. The radiolabeling yields were more than 80%. The labeled compound was dialysis in phosphate buffer. The radiochemical purity was 98%. The 90 Y- albumin is an ideal radiopharmaceutical for potential use in malignant cancer treatment as brachytherapy. (author)

Structural and magnetic properties of yttrium iron garnet (YIG) and yttrium aluminum iron garnet (YAIG) nanoferrites prepared by microemulsion method

Energy Technology Data Exchange (ETDEWEB)

Akhtar, Majid Niaz, E-mail: majidniazakhtar@ciitlahore.edu.pk [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Bakar Sulong, Abu [Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Khan, Muhammad Azhar [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Ahmad, Mukhtar [Department of Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan); Murtaza, Ghulam [Centre for Advanced Studies in Physics, G.C. University, Lahore, Pakistan" f Department of Mechanical Engineering, COMSATS Institute of Information Technology Sahiwal Pakistan (Pakistan); Raza, M.R. [Department of Mechanical and Materials Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia); Department of Mechanical Engineering, COMSATS Institute of Information Technology Sahiwal (Pakistan); Raza, R.; Saleem, M. [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Kashif, M. [Department of Physics, Govt. College University Faisalabad (Pakistan)

2016-03-01

Yttrium iron garnet (YIG) and yttrium aluminum iron garnet (YAIG) nanoferrite samples were synthesized by microemulsion method. The effect of sintering was examined by heating the samples at 900, 1000, and 1100 °C. The YIG and YAIG samples were then characterized using X-ray diffraction and field-emission scanning electron microscopy. Static and dynamic magnetic properties were measured by evaluating initial permeability, Q factor, and vibrating sample magnetometry properties of YIG and YAIG samples. YIG samples sintered at 1100 °C showed higher initial permeability and Q factor compared with YAIG samples. However, hysteresis loops also showed variations in the saturation magnetization, remanence, and coercivity of YIG and YAIG samples sintered at 900, 1000, and 1100 °C. The observed magnetic parameter such as saturation magnetization, coercivity and initial permeability are strongly affected by increasing temperature. The saturation magnetization and coercivity of YIG and YAIG nanoferrites were found in the range 11.56–19.92 emu/g and 7.30–87.70 Oe respectively. Furthermore, the decreasing trends in the static and magnetic properties of YAIG samples may be due to the introduction of Al ions in the YIG crystal lattice. Thus, YIG and YAIG sintered at 1100 °C can be used for wide-ranging frequency applications. - Highlights: • Static and dynamic magnetic properties of YIG and YAIG nanoferrites were determined. • Saturation magnetization, Q and initial permeability increased in YIG nanoferites. • Possible use of these nanoferrites for sensing and switching applications.

Spark plasma sintering of tungsten-yttrium oxide composites from chemically synthesized nanopowders and microstructural characterization

International Nuclear Information System (INIS)

Yar, M.A.; Wahlberg, Sverker; Bergqvist, Hans; Salem, H.G.; Johnsson, Mats; Muhammed, Mamoun

2011-01-01

Nano-crystalline W-1%Y 2 O 3 (wt.%) powder was produced by a modified solution chemical reaction of ammonium paratungstate (APT) and yttrium nitrate. The precursor powder was found to consist of particles of bimodal morphology i.e. large APT-like particles up to 20 μm and rectangular yttrium containing ultrafine plates. After thermal processing tungsten crystals were evolved from W-O-Y plate like particles. spark plasma sintering (SPS) was used to consolidate the powder at 1100 and 1200 deg. C for different holding times in order to optimize the sintering conditions to yield high density but with reduced grain growth. Dispersion of yttrium oxide enhanced the sinterability of W powder with respect to lanthanum oxide. W-1%Y 2 O 3 composites with sub-micron grain size showed improved density and mechanical properties as compared to W-La 2 O 3 composites. Sample sintered in two steps showed improved density, due to longer holding time at lower temperature (900 deg. C) and less grain growth due to shorter holding time at higher temperature i.e. 1 min at 1100 deg. C.

High-performance carbon-nanotube-based complementary field-effect-transistors and integrated circuits with yttrium oxide

Energy Technology Data Exchange (ETDEWEB)

Liang, Shibo; Zhang, Zhiyong, E-mail: zyzhang@pku.edu.cn; Si, Jia; Zhong, Donglai; Peng, Lian-Mao, E-mail: lmpeng@pku.edu.cn [Key Laboratory for the Physics and Chemistry of Nanodevices, Department of Electronics, Peking University, Beijing 100871 (China)

2014-08-11

High-performance p-type carbon nanotube (CNT) transistors utilizing yttrium oxide as gate dielectric are presented by optimizing oxidization and annealing processes. Complementary metal-oxide-semiconductor (CMOS) field-effect-transistors (FETs) are then fabricated on CNTs, and the p- and n-type devices exhibit symmetrical high performances, especially with low threshold voltage near to zero. The corresponding CMOS CNT inverter is demonstrated to operate at an ultra-low supply voltage down to 0.2 V, while displaying sufficient voltage gain, high noise margin, and low power consumption. Yttrium oxide is proven to be a competitive gate dielectric for constructing high-performance CNT CMOS FETs and integrated circuits.

Separation of yttrium (III) from lanthanoids (III) by solvent extraction with substituted N-Alkylcarbonyl-N-phenylhydroxylamines

International Nuclear Information System (INIS)

Haraguchi, K.; Ogata, T.; Nakagawa, K.; Saitoh, T.; Kamidate, T.; Watanabe, H.

1996-01-01

A series of substituted N-alkylcarbonyl-N-phenylhydroxylamines(R-PHAs) were synthesized and utilized for the extraction of yttrium(III) and lanthanoids(III) in order to obtain effective extractants for the separation of yttrium(III) from the lanthanoids(III) and the mutual separation of the lanthanoids(III). The distribution ratio of yttrium(III) and the lanthanoids(III) between the carbon tetrachloride and the aqueous phases was measured as functions of the pH and the extractant concentration at 298 K at an ionic strength of 0.1 (NaNO 3 ). Yttrium(III) and the lanthanoids(III) were extracted with R-PHAs(HL) as self-adducted chelates of the form, ML 3 (HL) x , where 'x' is 1, 2 or 3 depending on the extraction system. The extractability of the metal ions decreased in the order of R-PHA having a primary, a secondary and a tertiary alkyl substituent attached to the carbonyl group because of the steric hindrance of the alkyl group. The separation factors for both Yb/Eu and Yb/Y pairs increased with increasing branching of the alkyl group of R-PHA. The excellent selectivity of R-PHAs having a tertiary alkyl group was attributable to a greater inductive effect of the tertiary alkyl group than those of the primary and secondary alkyl groups. The substituents at the phenyl group of R-PHAs gave no significant effect on the selectivity, while the extractability was enhanced considerably by introduction of electron withdrawing substituents at appropriate positions of the phenyl group of R-PHAs. (authors)

Electrical conductivity of zirconia and yttrium-doped zirconia from Indonesian local zircon as prospective material for fuel cells

International Nuclear Information System (INIS)

Apriany, Karima; Permadani, Ita; Rahmawati, Fitria; Syarif, Dani G.; Soepriyanto, Syoni

2016-01-01

In this research, zirconium dioxide, ZrO 2 , was synthesized from high-grade zircon sand that was founded from Bangka Island, Sumatra, Indonesia. The zircon sand is a side product of Tin mining plant industry. The synthesis was conducted by caustic fusion method with considering definite stoichiometric mole at every reaction step. Yttrium has been doped into the prepared zirconia by solid state reaction. The prepared materials were then being analyzed by X-ray diffraction equipped with Le Bail refinement to study its crystal structure and cell parameters. Electrical conductivity was studied through impedance measurement at a frequency range of 20 Hz- 5 MHz. Morphological analysis was conducted through Scanning Electron Microscopy (SEM) equipped with Energy Dispersive X-ray (EDX) for elemental analysis. The results show that the prepared yttrium stabilized zirconia, YSZ, was crystallized in the cubic structure with a space group of P42/NMC. The sintered zirconia and yttrium stabilized zirconia at 8 mol% of yttrium ions (8YSZ) show dense surface morphology with a grain size less than 10 pm. Elemental analysis on the sintered zirconia and 8YSZ show that sintering at 1500°C could eliminate the impurities, and the purity became 81.30%. Impedance analysis shows that ZrO 2 provide grain and grain boundary conductivity meanwhile 8YSZ only provide grain mechanism. The yttrium doping enhanced the conductivity up to 1.5 orders. The ionic conductivity of the prepared 8YSZ is categorized as a good material with conductivity reach 7.01 x10 -3 at 700 °C. The ionic conductivities are still lower than commercial 8YSZ at various temperature. It indicates that purity of raw material might significantly contribute to the electrical conductivity. (paper)

Experimental-statistical method for investigation of multicomponent yttrium garnet systems

International Nuclear Information System (INIS)

Kojouharoff, V.; Ionchey, H.

1986-01-01

In the present work, some problems are discussed arising in the construction and study of a mathematical model describing the synthesis of multicomponent yttrium garnets with predetermined microwave parameters. To construct the model, the following formula was used for Ca-V YIG substituted with In and Cr: Y/sub 3-2x/Ca/sub 2x/Fe/sub 5-(x+y+z)/In/sub y/Cr/sub z/V/sub x/O/sub 12/. For this purpose, ferrogarnets were synthesized differing in x, y, and z with their values chosen so as to obtain real roots of a set of equations of the type Y/sub k/ = ΣB/sub i/X/sub i/ + ΣB/sub ij/X/sub i/X/sub j/ + ΣB/sub ijk/X/sub i/X/sub j/X/sub k/, where Y/sub k/ are the ferrogarnet microwave properties. The graphical presentation of these solutions as triple diagrams is a very convenient way of obtaining ferrogarnets with predetermined microwave characteristics. The possibility is created of mathematically predicting and determining the influence of the different components on the yttrium ferrogarnet parameters as a function of their concentration

Equilibrium Studies on the Extraction of Yttrium from Chloride Medium by Mono (2-Ethylhexyl) 2-Ethylhexyl Phosphonic Acid (Ion quest 801)

International Nuclear Information System (INIS)

Zaki, E.E.; Ismail, Z.H.; Aly, H.F.; Sabet, S.A.

2008-01-01

Since 90 Y is one of the useful radioisotopes in nuclear medicine, liquid-liquid extraction of yttrium from chloride medium has been studied under various conditions using neutralized and un-neutralized mono (2-ethylhexyl) 2-ethylhexyl phosphonic acid (EHEHPA) as an extractant. Effect of reagent concentration, ph of the aqueous medium, metal ion concentration and nature of the diluent on the extraction process has been carried out. Effect of temperature was studied and thermodynamic parameters were evaluated. Yttrium extracted in organic phase was stripped with various reagents. The stoichiometry of the extracted species of yttrium was determined on the basis of slope analysis of experimental results. Equilibrium equations of the extraction process have been estimated and verified

Effect of rare earth element yttrium addition on microstructures and properties of a 21Cr-11Ni austenitic heat-resistant stainless steel

International Nuclear Information System (INIS)

Chen, Lei; Ma, Xiaocong; Wang, Longmei; Ye, Xiaoning

2011-01-01

Research highlights: → Applications of Y in 21Cr-11Ni austenitic heat-resistant stainless steel. → Sensible characteristics of microstructure and properties have been observed. → Y has been found be effective in improving hot ductility of 21Cr-11Ni steel. → Inhibitory effect of Y on S segregation to the grain boundary has been observed. -- Abstract: In this comparative study, the microstructure and the mechanical properties of a 21Cr-11Ni austenitic heat-resistant stainless steel with and without addition of rare earth (RE) element yttrium have been investigated. The results show that a number of fine spherical yttrium-rich oxide particles are not uniformly distributed in the matrix of steel with yttrium; instead, they are aligned along the rolling direction. The grains surrounding the alignment are nearly one order of magnitude smaller than those farther away from the alignment. The approximate calculation results indirectly show that the grain refinement may be mainly attributed to the stimulation for nucleation of recrystallization rather than to pinning by particles. Furthermore, the alignment has resulted in significant loss in transverse impact toughness and tensile elongation at room temperature. There is a trough in the hot ductility-temperature curve, which is located between 973 and 1173 K. The ductility trough of steel with yttrium becomes shallow within a certain temperature range, especially around 1073 K, indicating that improvement on hot ductility is achieved by yttrium addition. The results may be attributed to the increase of grain boundary cohesion indicated by the effective improvement on intergranular failure tendency, and the inhibitory effect of yttrium on sulfur segregation to grain boundaries is believed to be an important cause.

Peripheral Blood Lymphocyte Depletion After Hepatic Arterial {sup 90}Yttrium Microsphere Therapy for Hepatocellular Carcinoma

Energy Technology Data Exchange (ETDEWEB)

Carr, Brian I., E-mail: brianicarr@hotmail.com [Department of Surgery, University of Pittsburgh Medical Center, Pittsburgh, PA and Department of Nutrition and Exptl Biology, Saverio De Bellis Medical Research Institute, Castellana Grotte, Bari (Italy); Metes, Diana M. [Department of Surgery, University of Pittsburgh Medical Center, Pittsburgh, PA and Department of Nutrition and Exptl Biology, Saverio De Bellis Medical Research Institute, Castellana Grotte, Bari (Italy)

2012-03-01

Purpose: The short- and long-term effects of {sup 90}Yttrium microspheres therapy for hepatocellular carcinoma (HCC) on peripheral blood lymphocytes are unknown and were therefore examined. Methods and Materials: Ninety-two HCC patients were enrolled in a {sup 90}Yttrium therapy study and routine blood counts were examined as part of standard clinical monitoring. Results: We found an early, profound, and prolonged lymphopenia. In a subsequent cohort of 25 additional HCC patients, prospective flow cytometric immune-monitoring analysis was performed to identify specific changes on distinct lymphocyte subsets (i.e., CD3, CD4, CD8 T, and CD19 B lymphocytes) and NK cells absolute numbers, in addition to the granulocytes and platelets subsets. We found that the pretreatment lymphocyte subset absolute numbers (with the exception of NK cells) had a tendency to be lower compared with healthy control values, but no significant differences were detected between groups. Posttherapy follow-up revealed that overall, all lymphocyte subsets, except for NK cells, were significantly (>50% from pretherapy values), promptly (as early as 24 h) and persistently (up to 30 months) depleted post-{sup 90}Yttrium microspheres therapy. In contrast, granulocytes increased rapidly (24 h) to compensate for lymphocyte depletion, and remained increased at 1-year after therapy. We further stratified patients into two groups, according to survival at 1 year. We found that lack of recovery of CD19, CD3, CD8, and especially CD4 T cells was linked to poor patient survival. No fungal or bacterial infections were noted during the 30-month follow-up period. Conclusions: The results show that lymphocytes (and not granulocytes, platelets, or NK cells) are sensitive to hepatic arterial {sup 90}Yttrium without associated clinical toxicity, and lack of lymphocyte recovery (possibly leading to dysregulation of adaptive cellular immunity) posttherapy indicates poor survival.

Polymer Derived Yttrium Silicate Ablative TPS Materials for Next-Generation Exploration Missions, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Through the proposed NASA SBIR program, NanoSonic will optimize its HybridSil® derived yttrium silicates to serve as next-generation reinforcement for carbon and...

Mass synthesis of yttrium oxide nano-powders using radio frequency (RF) plasma

International Nuclear Information System (INIS)

Ghorui, S.; Sahasrabudhe, S.N.; Chakravarthy, Y.; Nagaraj, A.; Das, A.K.; Dhamale, G.

2014-01-01

Mass synthesis of nano-phase Yttrium Oxide (Y 2 O 3 ) from commercially available coarse grain powder is reported. Nano-sized high purity Y 2 O 3 is an important and critical constituent of ceramics like YAG (Yttrium aluminum garnet: Y 3 Al 5 O 12 ) for laser applications. The system is characterized in terms of its thermal and electrical behavior. Boltzmann plot technique is used to measure axial variation of temperature of the generated plasma. The synthesized particles are characterized in terms of XRD, SEM, TEM and BET analyses for qualification of the developed system. Major features observed are efficient conversion into nanometer-sized highly spherical particles, narrow size distribution, highly crystallite nature and highly pure phases. The particle distribution (from TEM) peaks within 20-30 nm. Average particle sizes determined from different methods like XRD, TEM and BET are very close to each other and point toward particle sizes within 20 to 30 nm

Analysis of Prognostic Factors After Yttrium-90 Radioembolization of Advanced Hepatocellular Carcinoma

International Nuclear Information System (INIS)

Inarrairaegui, Mercedes; Martinez-Cuesta, Antonio; Rodriguez, Macarena; Bilbao, J. Ignacio

2010-01-01

Purpose: To analyze which patient-, tumor-, and treatment-related factors may influence outcome after 90 Y radioembolization ( 90 Y-RE) for hepatocellular carcinoma (HCC). Patients and Methods: Seventy-two consecutive patients with advanced HCC treated with 90 Y-RE were studied to detect which factors may have influenced response to treatment and survival. Results: Median overall survival was 13 months (95% confidence interval, 9.6-16.3 months). In univariate analysis, survival was significantly better in patients with one to five lesions (19 vs. 8 months, p = 0.001) and in patients with alpha-fetoprotein 52 UI/mL, and their survival in the multivariate analysis was significantly worse (hazard ratio, 4.7; 95% confidence interval, 13-1.73) (p = 0.002). Conclusions: Yttrium-90 radioembolization results in control of target lesions in the majority of patients with HCC but does not prevent the development of new lesions. Survival of patients treated with 90 Y-RE seems to depend largely on factors related to the aggressiveness of the disease (number of nodules, levels of alpha-fetoprotein, and presence of microscopic disease).

Cerium and yttrium oxide nanoparticles are neuroprotective

International Nuclear Information System (INIS)

Schubert, David; Dargusch, Richard; Raitano, Joan; Chan, S.-W.

2006-01-01

The responses of cells exposed to nanoparticles have been studied with regard to toxicity, but very little attention has been paid to the possibility that some types of particles can protect cells from various forms of lethal stress. It is shown here that nanoparticles composed of cerium oxide or yttrium oxide protect nerve cells from oxidative stress and that the neuroprotection is independent of particle size. The ceria and yttria nanoparticles act as direct antioxidants to limit the amount of reactive oxygen species required to kill the cells. It follows that this group of nanoparticles could be used to modulate oxidative stress in biological systems

Decision tree analysis to assess the cost-effectiveness of yttrium microspheres for treatment of hepatic metastases from colorectal cancer

International Nuclear Information System (INIS)

Kelley, B.B.; Walker, G.D.; Miles, K.A.

2002-01-01

Full text: The aim is to determine the cost-effectiveness of yttrium microsphere treatment of hepatic metastases from colorectal cancer, with and without FDG-PET for detection of extra-hepatic disease. A decision tree was created comparing two strategies for yttrium treatment with chemotherapy, one incorporating PET in addition to CT in the pre-treatment work-up, to a strategy of chemotherapy alone. The sensitivity and specificity of PET and CT were obtained from the Federal Government PET review. Imaging costs were obtained from the Medicare benefits schedule with an additional capital component added for PET (final cost $1200). The cost of yttrium treatment was determined by patient-tracking. Previously published reports indicated a mean gain in life-expectancy from treatment of 0.52 years. Patients with extra-hepatic metastases were assumed to receive no survival benefit. Cost effectiveness was expressed as incremental cost per life-year gained (ICER). Sensitivity analysis determined the effect of prior probability of extra-hepatic disease on cost-savings and cost-effectiveness. The cost of yttrium treatment including angiography, particle perfusion studies and bed-stays, was $10530. A baseline value for prior probability of extra-hepatic disease of 0.35 gave ICERs of $26,378 and $25,271 for the no-PET and PET strategies respectively. The PET strategy was less expensive if the prior probability of extra-hepatic metastases was greater than 0.16 and more cost-effective if above 0.28. Yttrium microsphere treatment is less cost-effective than other interventions for colon cancer but comparable to other accepted health interventions. Incorporating PET into the pre-treatment assessment is likely to save costs and improve cost-effectiveness. Copyright (2002) The Australian and New Zealand Society of Nuclear Medicine Inc

Use of yttrium-90 microspheres (TheraSphere) in a patient with unresectable hepatocellular carcinoma leading to liver transplantation: a case report.

Science.gov (United States)

Kulik, Laura M; Mulcahy, Mary F; Hunter, Russell D; Nemcek, Albert A; Abecassis, Michael M; Salem, Riad

2005-09-01

Prior to therapy, model for end stage liver disease (MELD) scoring, diagnostic imaging and tumor staging were performed in a patient with T3 HCC. The patient received an orthotopic liver transplant (OLT) 42 days after treatment. The explant specimen showed complete necrosis of the target tumor. Follow-up of this patient has demonstrated no evidence of recurrence. There was no life threatening or fatal adverse experiences related to treatment. This case report documents the natural course, history and outcome of a patient treated with yttrium-90 for unresectable HCC. The patient was downstaged from T3 to T2 and was subsequently transplanted.

Influence of neodymium-doping on structure and properties of yttrium aluminium garnet

DEFF Research Database (Denmark)

Zhang, X.D.; He, W.; Yue, Yuanzheng

2013-01-01

We study the impact of the Nd-doping on the grain formation, the crystal structure, and the fluorescence of the Yttrium Aluminum Garnet (YAG). The results show that Nd-doping leads to the YAG lattice expansion and distortion, and hence to an increase in defect concentration. This is attributed to...

Separation of yttrium from strontium in the aqueous phase of the water/nitrobenzene system

Czech Academy of Sciences Publication Activity Database

Vaňura, P.; Makrlík, E.; Vobecký, Miloslav

2002-01-01

Roč. 253, č. 1 (2002), s. 171-172 ISSN 0236-5731 Institutional research plan: CEZ:AV0Z4031919 Keywords : stroncium * yttrium * separation Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 0.502, year: 2002

Separation of microamounts of yttrium from strontium in the two-phase water/nitrobenzene system

Czech Academy of Sciences Publication Activity Database

Makrlík, E.; Vaňura, P.; Vobecký, Miloslav

2002-01-01

Roč. 253, č. 1 (2002), s. 153-155 ISSN 0236-5731 Institutional research plan: CEZ:AV0Z4031919 Keywords : separation * stroncium * yttrium Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 0.502, year: 2002

Status and prospects on development of yttrium-based high-temperature superconducting coated conductor

International Nuclear Information System (INIS)

Izumi, Teruo; Yanagi, Nagato

2017-01-01

Development of a large-sized large-current conductor using a high-temperature superconducting wire rod based on copper oxide has been started worldwide for the purpose of applying it as an option of a magnet for a nuclear fusion prototype reactor. There is yttrium-based thin film wire rod as a promising candidate. Japan is leading the development of this wire rod for many years, aiming to apply it to power equipment and the like. This paper explained the history of wire rod development, basic superconducting properties and manufacturing method, and latest achievements, and overviewed the feasibility of application to nuclear fusion reactor magnets. At present, the use of niobium-based low-temperature superconducting wire rod that is used in ITER is the basic idea. On the other hand, the development of wire rod using a copper oxide type high-temperature superconductor (HTS) has also been started. HTS wire rod is evaluated as suitable for application to nuclear fusion magnets due to its superior critical current characteristics and high mechanical rigidity up to high magnetic fields at high temperatures of yttrium. As current development progress, there are development of high-quality wire rod in the magnetic field and development of low AC loss wire rod. As future prospects, cost reduction due to mass production and improvement of yield, and investigation of low-resistance connection technology are being studied. The remaining future challenges of yttrium-based HTS are improvement of the anisotropy, influence on neutron irradiation, and problem of activation. (A.O.)

An XRF method for determination of common rare earth impurities in high purity yttrium oxide

International Nuclear Information System (INIS)

Dixit, R.M.; Deshpande, S.S.

1975-01-01

An XRF method for the estimation of Eu, Gd, Tb, Dy, Ho, Er and Yb in yttrium oxide has been developed. Samples are converted to yttrium oxalate and presented to the spectrometer in the form of pressed pellets. Philips PW-1220, a semi-automatic x-ray spectrometer, is used for the analysis. Line interference problems are studied for selecting analysis lines. For the elements except that of Yb, the lower estimation limit is 0.005% and for Yb, it is 0.01%. The average standard deviation is approximately 5% for various elements in the concentration range of 0.005% to 1.0%. The method has been tested for its accuracy by analysing synthesized samples with known composition at three different concentrations. (author)

ELECTRON MICROSCOPIC INVESTIGATION OF YTTRIUM ALUMINUM GARNET POWDERS Y3AL5O12, SYNTHESIZED BY SOL–GEL METHOD

OpenAIRE

A. E. Baranchikov; V. A. Maslov; S. V. Shcherbakov; V. A. Usachyov; N. E. Kononenko; P. P. Fedorov; K. V. Dukelskiy

2015-01-01

Subject of Study. The paper presents results of characterization for neodymium doped yttrium aluminum garnet nanopowders - YAG:Nd3+ by the method of scanning electronic microscopy. Method. Synthesis of YAG:Nd3+ was carried out by sol-gel method from nitrate or acetate - nitrate solutions with addition of some organic compounds and ammonia as well. Such substances were used as the source ones: oxides of neodymium and yttrium with the content of the basic substance equal to 99.999 %; organic co...

Adducts compounds of lanthanides (III) trifluoreacetates and yttrium and the N,N - dimenthylformamide

International Nuclear Information System (INIS)

Silva, M. das G. da.

1983-01-01

Some studies on lanthanides, f transition elements, and yttrium are presented. Adducts of lanthanides trifluoroacetates and N,N -dimethylformamide are described. The characterization of complexes from elementar analysis, conductance measurements, X-ray patterns, vibrational, electronics and fluorescence spectra are analysed. (M.J.C.) [pt

The effect of yttrium addition on oxidation of a sputtered nanocrystalline coating with moderate amount of tantalum in composition

International Nuclear Information System (INIS)

Wang, Jinlong; Chen, Minghui; Yang, Lanlan; Liu, Li; Zhu, Shenglong; Wang, Fuhui; Meng, Guozhe

2016-01-01

Graphical abstract: - Highlights: • Effect of Y addition on oxidation of nanocrystalline coating is studied. • Y addition delays transformation of q-Al_2O_3 to a-Al_2O_3 during oxidation. • Y addition prevents scale rumpling. • Y segregates at grain boundaries of the nanocrystalline coating. • Y retards the transportation of Ta thus reduces its oxidation. - Abstract: The effect of yttrium addition on isothermal oxidation at 1050 °C of a sputtered nanocrystalline coating with moderate amount of tantalum in composition was investigated. Results indicate that yttrium addition delays transformation of metastable θ-Al_2O_3 to equilibrium α-Al_2O_3 grown on the nanocrystalline coatings. It prevents scale rumpling and promotes the formation of oxide pegs at interface between the oxide scale and the underlying coating. Besides, yttrium prefers to segregate at grain boundaries of the nanocrystalline coating and retards the outward transportation of tantalum from coating to oxide scale, thus reducing the excessive oxidation of tantalum.

Kinetic properties of solid yttrium at high temperatures

International Nuclear Information System (INIS)

Ivliev, A.D.

1993-01-01

Analysis of results of experimental investigation into temperature-diffusivity, specific electroresistance and heat conductivity of yttrium is carried out. Peculiarities of variation of its kinetic characteristics under high temperatures are shown to result from two-band character of energy spectrum of collectivized electrons. In particular, growth of heat conductivity results from reduction of density of heavy electron states under heating. The suggested model describes kinetic characteristics of lutetium, as well. Usage of this model for the rest heavy rare-earth metals enables to make conclusion about reduction of magnetic scattering effcieincy in the rare-earth metals in proportion to approximation to melting temperature

Acromegaly with sleep disturbances relieved by yttrium-90 pituitary implantation

International Nuclear Information System (INIS)

Rosenstock, J.; Doyle, F.H.; Joplin, G.F.; Jung, R.T.; Mashiter, K.

1982-01-01

A brief case history is presented of a patient, who, after yttrium-90 implantation, showed a complete clinical and hormonal remission of her acromegaly, maintaining normal pituitary function. The remarkable feature was the rapid disappearance of her attacks of somnolence within 96 hours of pituitary implantation, despite persistence of nocturnal snoring and well before any remodelling of soft tissues could have occurred. This response suggests that her daytime somnolence had a narcoleptic component. (author)

Acromegaly with sleep disturbances relieved by yttrium-90 pituitary implantation

Energy Technology Data Exchange (ETDEWEB)

Rosenstock, J.; Doyle, F.H.; Joplin, G.F.; Jung, R.T.; Mashiter, K. (Hammersmith Hospital, London (UK). Postgraduate Medical School)

1982-03-01

A brief case history is presented of a patient, who, after yttrium-90 implantation, showed a complete clinical and hormonal remission of her acromegaly, maintaining normal pituitary function. The remarkable feature was the rapid disappearance of her attacks of somnolence within 96 hours of pituitary implantation, despite persistence of nocturnal snoring and well before any remodelling of soft tissues could have occurred. This response suggests that her daytime somnolence had a narcoleptic component.

Separation of yttrium using carbon nanotube doped polymeric beads impregnated with D2EHPA

International Nuclear Information System (INIS)

Dasgupta, Kinshuk; Yadav, Kartikey K.; Singh, D.K.; Anitha, M.; Singh, H.

2013-01-01

Di-2-ethylhexyl phosphoric acid impregnated polyethersulfone based composite beads in combination with additives such as polyvinyl alcohol (PVA) and multiwalled carbon nanotube (MWCNT) has been prepared by non-solvent phase inversion method. The synthesized beads were characterized by scanning electron microscopy, thermogravimetry and infra-red spectroscopy. Effect of additives on bead morphology, solvent impregnation capacity, extractability and stability has been examined to compare their suitability for yttrium recovery from acidic medium. Microstructural investigation as well as experimental findings confirmed the role of additives in modifying the pore structures in beads, responsible for varied degree of yttrium extraction. Further the role of metal ion concentration in aqueous phase on its recovery by polymeric beads was also evaluated. Among the tested beads PES/D2EHPA/MWCNT/PVA beads were found to be superior for Y(Ill) extraction. (author)

Determination of yttrium using YO band head obtained by laser enhanced ionization spectrometry

International Nuclear Information System (INIS)

Deshpande, S.S.; Khanna, P.P.

1997-04-01

The determination of yttrium (Y) in water in the concentration range of 2 μg/ml to 200 μg/ml by laser enhanced ionisation (LEI) technique is reported. The YO band head at 584.27 nm belonging to A 2 Π - X 2 Σ + system is used for LEI signal detection. It is also shown that the LEI signal is enhanced when the mixture of air - acetylene - argon (AAA) is used instead of commonly used air-acetylene (AA) mixture. In the present work an XeCl laser (308 nm) pumped rhodamine 6G dye laser, covering a range of 570-610 nm is used. The sample/standard in solution form is aspirated into the flame with pneumatic nebulizer. The working curve is a straight line showing linear dependence of LEI signal with yttrium concentration. The relative standard deviation calculated at 100 μg/ml is found to be 2.4 %. (author)

Scanning-SQUID investigation of spin-orbit torque acting on yttrium iron garnet devices

Science.gov (United States)

Rosenberg, Aaron J.; Jermain, Colin L.; Aradhya, Sriharsha V.; Brangham, Jack T.; Nowack, Katja C.; Kirtley, John R.; Yang, Fengyuan; Ralph, Daniel C.; Moler, Kathryn A.

Successful manipulation of electrically insulating magnets, such as yttrium iron garnet, by by current-driven spin-orbit torques could provide a highly efficient platform for spintronic memory. Compared to devices fabricated using magnetic metals, magnetic insulators have the advantage of the ultra-low magnetic damping and the elimination of shunting currents in the magnet that reduce the torque efficiency. Here, we apply current in the spin Hall metal β-Ta to manipulate the magnetic orientation of micron-sized, electrically-insulating yttrium iron garnet devices. We do not observe spin-torque switching even for applied currents well above the critical current expected in a macrospin switching model. This suggests either inefficient transfer of spin torque at our Ta/YIG interface or a breakdown of the macrospin approximation. This work is supported by FAME, one of six centers of STARnet sponsored by MARCO and DARPA. The SQUID microscope and sensors were developed with support from the NSF-sponsored Center NSF-NSEC 0830228, and from NSF IMR-MIP 0957616.

Physicochemical properties and ecotoxicological effects of yttrium oxide nanoparticles in aquatic media: Role of low molecular weight natural organic acids

International Nuclear Information System (INIS)

Zhang, Fan; Wang, Zhuang; Wang, Se; Fang, Hao; Chen, Mindong; Xu, Defu; Tang, Lili; Wang, Degao

2016-01-01

Understanding how engineered nanoparticles (ENPs) interact with natural organic acids is important to ecological risk assessment of ENPs, but this interaction remains poorly studied. Here, we investigate the dispersion stability, ion release, and toxicity of yttrium oxide nanoparticles (nY_2O_3) suspensions after exposure to two low molecular weight natural organic acids (LOAs), namely benzoic acid and gallic acid. We find that in the presence of LOAs the nY_2O_3 suspensions become more stable with surface zeta potential more positive or negative, accompanied by small agglomerated size. LOA interaction with nY_2O_3 is shown to promote the release of dissolved yttrium from the nanoparticles, depending on the concentrations of LOAs. Toxic effects of the nY_2O_3 suspensions incubated with LOAs on Scenedesmus obliquus as a function of their mixture levels show three types of signs: stimulation, inhibition, and alleviation. The mechanism of the effects of LOAs on the nY_2O_3 toxicity may be mainly associated with the degree of agglomeration, particle-induced oxidative stress, and dissolved yttrium. Our results stressed the importance of LOA impacts on the fate and toxicity of ENPs in the aquatic environment. - Highlights: • LOAs significantly increased aqueous stability of nY2O3 in a dose-dependent manner. • The presence of LOAs promoted dissolution of nY2O3 in a dose-dependent manner. • Toxicity of nY2O3 with LOAs to Scenedesmus obliquus varied with mixture levels. • Stimulation, inhibition, and alleviation effects of nY2O3 with LOAs were observed. • Mechanism may be driven by agglomeration, oxidative stress, and dissolved yttrium. - LOAs elevate the dispersion stability of nano-Y_2O_3, promote the release of dissolved yttrium, and alter the algal toxicity of nano-Y_2O_3.

Thermal decomposition of double selenates of lanthanides (III), yttrium (III) and ammonium

International Nuclear Information System (INIS)

Crespi, M.S.

1989-01-01

Double selenates of lanthanides, yttrium and ammonium were prepared by treating mixtures of simple selenates with equimolar amounts and then dried in a vacuum desiccator containing anhydrous calcium chloride, protected from light. The compounds were studied using the conventional analytical methods such as infrared absorption spectra, X-ray diffraction, differential thermal analysis (DTA), and thermogravimetry (TG). (author)

Structural differences of half-sandwich complexes of scandium and yttrium containing bulky substituents

Czech Academy of Sciences Publication Activity Database

Fridrichová, Adéla; Růžička, A.; Lamač, Martin; Horáček, Michal

2017-01-01

Roč. 76, FEB 2017 (2017), s. 62-66 ISSN 1387-7003 R&D Projects: GA ČR(CZ) GAP207/12/2368 Institutional support: RVO:61388955 Keywords : scandium * yttrium * half-sandwich Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 1.640, year: 2016

Growth and scintillation properties of gadolinium and yttrium orthovanadate crystals

International Nuclear Information System (INIS)

Voloshina, O.V.; Baumer, V.N.; Bondar, V.G.; Kurtsev, D.A.; Gorbacheva, T.E.; Zenya, I.M.; Zhukov, A.V.; Sidletskiy, O.Ts.

2012-01-01

Aiming to explore the possibility of using the undoped rare-earth orthovanadates as scintillation materials, we developed the procedure for growth of gadolinium (GdVO 4 ) and yttrium (YVO 4 ) orthovanadate single crystals by Czochralski method, and determined the optimal conditions of their after-growth annealing. Optical, luminescent, and scintillation properties of YVO 4 and GdVO 4 were discussed versus known literature data. Scintillation characteristics of GdVO 4 were determined for the first time.

Study on the coextraction of scandium-yttrium-lumogallion complex

International Nuclear Information System (INIS)

Okada, T.; Shimoishi, Y.; Miyata, H.; Toei, K.

1977-01-01

The coextraction of scandium-yttrium-lumogallion [LMG;4-chloro-6-(2,4-dihydroxyphenylazo)-1-hydroxybenzene-2-sulfonic acid] into diethyl ether has been studied. The acid dissociation constants of LMG, pKsub(a2) and pKsub(a3), were estimated to be 6.24 and 8.05 respectively. The composition of the complex extracted was determined by using the radioisotopes 46 Sc and 90 Y and by spectrophotometry of LMG and the ratio of the components was Sc:Y:LMG = 1:1:3. The coextraction scheme was discussed briefly. (author)

Thiocarbomide coordination compounds of yttrium subgroup rare earth chlorides

International Nuclear Information System (INIS)

Sakharova, Yu.G.; Perov, V.N.; Loginov, V.I.

1978-01-01

Thiocarbamide coordination compounds of chlorides of elements of the yttrium subgroup 4MeCl 3 x5Cs(NH 2 ) 2 x2OH 2 O (where Me stands for Tb, Dy, Ho, Er, Tm, Yb, Lu, Y) were produced for the first time. The compounds obtained are stable in air, have definite melting points, are highly soluble in methyl and ethyl alcohols, and are unstable in water. They recrystallize from ethyl alcohol without changing their chemical composition. The identity of these compounds was confirmed by X-ray analysis

Production cross sections of proton-induced reactions on yttrium

Energy Technology Data Exchange (ETDEWEB)

Yang, Sung-Chul; Song, Tae-Yung; Lee, Young-Ouk [Nuclear Data Center, Korea Atomic Energy Research Institute, Daejeon 34057 (Korea, Republic of); Kim, Guinyun, E-mail: gnkim@knu.ac.kr [Department of Physics, Kyungpook National University, Daegu 41566 (Korea, Republic of)

2017-05-01

The production cross sections of residual radionuclides such as {sup 86,88,89g}Zr, {sup 86g,87m,87g,88}Y, {sup 83g,85g}Sr, and {sup 83,84g}Rb in the {sup 89}Y(p,x) reaction were measured using a stacked-foil activation and offline γ-ray spectrometric technique with proton energies of 57 MeV and 69 MeV at the 100 MeV proton linac in the Korea Multi-purpose Accelerator Complex (KOMAC), Gyeongju, Korea. The induced activities of the activated samples were measured using a high purity germanium (HPGe) detector, and the proton flux was determined using the {sup nat}Cu(p,x){sup 62}Zn reaction. The measured data was compared with other experimental data and the data from the TENLD-2015 library based on the TALYS code. The present results are generally lower than those in literature, but are found to be in agreement with the shape of the excitation functions. The integral yields for the thick target using the measured cross sections are given.

Treatment of primary liver tumors with Yttrium-90 microspheres (TheraSphere) in high risk patients: analysis of survival and toxicities.

Science.gov (United States)

Reardon, Kelli A; McIntosh, Alyson F; Shilling, A Tanner; Hagspiel, Klaus D; Al-Osaimi, Abdullah; Berg, Carl; Caldwell, Stephen H; Northup, Patrick G; Angle, Fritz; Mulder, Robert; Rich, Tyvin A

2009-02-01

This retrospective study was undertaken to obtain information regarding the survival and toxicities after Yttrium-90 microspheres treatment in patients with primary liver malignancies. Baseline, treatment, and follow-up data were collected and analyzed for 21 patients treated with Yttrium-90 microspheres. Survival analysis was then performed. The results of this study showed that median survival for all the patients was 120 days. Twenty of 21 patients were categorized as high-risk with a median survival of 114 days. It was also found that one high-risk patient has survived 858 days with no recurrence of disease. Acute grade 3-5 toxicities were recorded for nine patients and consisted of elevations in AST and bilirubin, thrombocytopenia, abdominal pain, ascites, nausea, fatigue, and death. This study concluded that Yttrium-90 is a low-toxicity, outpatient alternative for individuals with liver cancer and without many options. The maximal value, however, may lie in the treatment of low-risk patients.

Spectrographic determination of strontium in yttrium-90 solutions

International Nuclear Information System (INIS)

Roca, M.; Capdevila, C.

1970-01-01

The copper spark method has been used for determining strontium in the concentration range 1-100 g/ml in yttrium-90 solutions containing 0,5 % or thereabouts of ammonium citrate. The influence of the citric acid as well as the ammonium citrate with regard to 2N HCL solutions has been studied: the citric acid enhances the line intensities of strontium. The employment of either barium or lanthanum as reference element compensates for this enhancement. Because of the increase in sensitivity mentioned above, the study of influence of the citric acid has been extended and several impurities usually determined in radioisotope solutions have been considered. (Author) 4 refs

Photometric determination of yttrium in zirconium-containing materials

International Nuclear Information System (INIS)

Barbina, T.M.; Polezhaev, Yu.M.

1984-01-01

Comparative evaluation of the effect of different ways of eliminating the zirconium interfering effect on the results of yttrium photometric determination with arsenazo 2 in artificial mixtures of Y 2 O 3 and ZrO 2 , containing 5 and 10 mol.% Y 2 O 3 , has been carried out. The effect of Zr is eliminated by means of its precipitation by ammonium solution in the form of hydroxide and using camouflaging with 25% sulfosalicylic acid. Both ways do not provide a correct enough result. The use of non-reagent thermohydrolytic Zr precipitation during the analysis of zirconium-containing materials permits to obtain correct and well-reproducible results

Yttrium orthoferrite powder obtained by the mechanochemical synthesis

Directory of Open Access Journals (Sweden)

Lazarević Zorica Ž.

2017-01-01

Full Text Available Yttrium orthoferrite (YFeO3 powder was prepared by a mechanochemical synthesis from a mixture of Y2O3 and α-Fe2O3 powders in a planetary ball mill for 2.5 h. The obtained YFeO3 powder sample was characterized by X-ray diffraction (XRD, Raman and infrared spectroscopy. The average crystallite size calculated by the Scherrer equation was 12 nm. The Mössbauer spectroscopy at room temperature confirms the superparamagnetic character of YFeO3 orthoferrite sample. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. III 45003, Grant no. III 45015, Grant no. III 45018

Nanoscale nonlinear effects in Erbium-implanted Yttrium Orthosilicate

Energy Technology Data Exchange (ETDEWEB)

Kukharchyk, Nadezhda, E-mail: nadezhda.kukharchyk@physik.uni-saarland.de [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany); Angewandte Festkörperphysik, Ruhr-Universität Bochum, D-44780 Bochum (Germany); Shvarkov, Stepan [Optoelektronische Materialien und Bauelemente, Universität Paderborn, D-33098 Padeborn (Germany); Probst, Sebastian [Quantronics group, Service de Physique de l' Etat Condense, DSM/IRAMIS/SPEC, CNRS UMR 3680, CEA-Saclay, 91191 Gif-sur-Yvette cedex (France); Xia, Kangwei [3. Physikalisches Institut, Universität Stuttgart, D-70569 Stuttgart (Germany); Becker, Hans-Werner [RUBION, Ruhr-Universität Bochum, D-44780 Bochum (Germany); Pal, Shovon [Angewandte Festkörperphysik, Ruhr-Universität Bochum, D-44780 Bochum (Germany); AG THz Spectroscopie und Technologie, Ruhr-Universität Bochum, D-44780 Bochum (Germany); Markmann, Sergej [AG THz Spectroscopie und Technologie, Ruhr-Universität Bochum, D-44780 Bochum (Germany); Kolesov, Roman; Siyushev, Petr; Wrachtrup, Jörg [3. Physikalisches Institut, Universität Stuttgart, D-70569 Stuttgart (Germany); Ludwig, Arne [Angewandte Festkörperphysik, Ruhr-Universität Bochum, D-44780 Bochum (Germany); Ustinov, Alexey V. [Physikalisches Institut, Karlsruhe Institute of Technology, D-76128 Karlsruhe (Germany); Wieck, Andreas D. [Angewandte Festkörperphysik, Ruhr-Universität Bochum, D-44780 Bochum (Germany); and others

2016-09-15

Doping of substrates at desired locations is a key technology for spin-based quantum memory devices. Focused ion beam implantation is well-suited for this task due to its high spacial resolution. In this work, we investigate ion-beam implanted Erbium ensembles in Yttrium Orthosilicate crystals by means of confocal photoluminescence spectroscopy. The sample temperature and the post-implantation annealing step strongly reverberate in the properties of the implanted ions. We find that hot implantation leads to a higher activation rate of the ions. At high enough fluences, the relation between the fluence and final concentration of ions becomes non-linear. Two models are developed explaining the observed behavior.

Long-Term Palliative Effect of Stenting in Gastric Outlet Obstruction Due to Transarterial Chemoembolization with Yttrium-90 in a Patient with Metastatic Neuroendocrine Tumor

Directory of Open Access Journals (Sweden)

Erkan Caglar

2016-09-01

Full Text Available Internal radioembolization with yttrium-90 is a promising treatment method, predominantly for liver tumors. However, the shifting of yttrium-90-loaded spherules into the arteries and veins that supply the duodenum and stomach, leading to ulceration, hemorrhage, perforation, and outlet obstruction of these organs, is one of the major undesirable consequences of this technique. We report a case of gastric outlet obstruction (GOO due to antropyloric stenosis with ulceration, edema, and inflammation following transarterial yttrium-90 treatment for a metastatic neuroendocrine tumor in a 58-year-old man. Stenting was used for palliation in this case. GOO improved after stenting and recovery of oral intake was permanent after stent removal.

Positron emission tomography imaging of CD105 expression with {sup 89}Zr-Df-TRC105

Energy Technology Data Exchange (ETDEWEB)

Hong, Hao; Yang, Yunan [University of Wisconsin - Madison, Department of Radiology, Madison, WI (United States); Severin, Gregory W.; Engle, Jonathan W.; Zhang, Yin; Barnhart, Todd E.; Nickles, Robert J. [University of Wisconsin - Madison, Department of Medical Physics, Madison, WI (United States); Liu, Glenn [University of Wisconsin - Madison, Department of Medicine, Madison, WI (United States); University of Wisconsin Carbone Cancer Center, Madison, WI (United States); Leigh, Bryan R. [TRACON Pharmaceuticals, Inc, San Diego, CA (United States); Cai, Weibo [University of Wisconsin - Madison, Department of Radiology, Madison, WI (United States); University of Wisconsin - Madison, Department of Medical Physics, Madison, WI (United States); University of Wisconsin Carbone Cancer Center, Madison, WI (United States)

2012-01-15

High tumor microvessel density correlates with a poor prognosis in multiple solid tumor types. The clinical gold standard for assessing microvessel density is CD105 immunohistochemistry on paraffin-embedded tumor specimens. The goal of this study was to develop an {sup 89}Zr-based PET tracer for noninvasive imaging of CD105 expression. TRC105, a chimeric anti-CD105 monoclonal antibody, was conjugated to p-isothiocyanatobenzyl-desferrioxamine (Df-Bz-NCS) and labeled with {sup 89}Zr. FACS analysis and microscopy studies were performed to compare the CD105 binding affinity of TRC105 and Df-TRC105. PET imaging, biodistribution, blocking, and ex-vivo histology studies were performed on 4T1 murine breast tumor-bearing mice to evaluate the pharmacokinetics and tumor-targeting of {sup 89}Zr-Df-TRC105. Another chimeric antibody, cetuximab, was used as an isotype-matched control. FACS analysis of HUVECs revealed no difference in CD105 binding affinity between TRC105 and Df-TRC105, which was further validated by fluorescence microscopy. {sup 89}Zr labeling was achieved with high yield and specific activity. Serial PET imaging revealed that the 4T1 tumor uptake of {sup 89}Zr-Df-TRC105 was 6.1 {+-} 1.2, 14.3 {+-} 1.2, 12.4 {+-} 1.5, 7.1 {+-} 0.9, and 5.2 {+-} 0.3 %ID/g at 5, 24, 48, 72, and 96 h after injection, respectively (n = 4), higher than all organs starting from 24 h after injection, which provided excellent tumor contrast. Biodistribution data as measured by gamma counting were consistent with the PET findings. Blocking experiments, control studies with {sup 89}Zr-Df-cetuximab, and ex-vivo histology all confirmed the in vivo target specificity of {sup 89}Zr-Df-TRC105. We report here the first successful PET imaging of CD105 expression with {sup 89}Zr as the radiolabel. Rapid, persistent, CD105-specific uptake of {sup 89}Zr-Df-TRC105 in the 4T1 tumor was observed. (orig.)

Hepatobiliary effects of 90yttrium microsphere therapy for unresectable hepatocellular carcinoma.

Science.gov (United States)

Nalesnik, Michael A; Federle, Michael; Buck, David; Fontes, Paulo; Carr, Brian I

2009-01-01

(90)Yttrium (Therasphere) microspheres administered via hepatic artery are a valuable option for treatment of hepatocellular carcinoma. This therapy targets tumor nodules while largely sparing hepatic parenchyma. This retrospective study examines liver explants from 13 adult patients with hepatocellular carcinoma who received intrahepatic Theraspheres and subsequently underwent liver transplantation. Histopathologic and laboratory reviews are performed. Theraspheres preferentially migrated to the lobe(s) supplied by the injected artery branches and frequently localized to tumors. Tumors showed a chronology of changes beginning with confluent necrosis typically accompanied by hemorrhage and later by fibrinoid change. This was followed by fibrosis with regenerative activity at tumor peripheries. Adjacent hepatic parenchyma went through a similar sequence of injury and repair that could lead to markedly fibrotic cirrhotic nodules in the vicinity of treated tumors. No consistent pattern of thrombomodulin loss was seen in endothelial cells of the tumors or adjacent parenchyma, suggesting that direct endothelial cell injury was likely not a major contributor to the necrotic process. However, the pattern of injury and repair is suggestive of a localized and subclinical form of radiation-induced liver disease. The pathologist should be aware of these changes to distinguish them from the diffuse "radiation hepatitis" associated with older forms of radiotherapy.

Some peculiarities of thermoemission of the cathodes on the base of tanthanum and yttrium oxides

International Nuclear Information System (INIS)

Podgornyj, V.I.

1982-01-01

Thermoemission cathode characteristics on the basis of (La 2 O 3 ) lanthanum, and yttrium oxides which are used already in prctice but emission mechanism of which remains yet insufficiently elucidated, were investigated. It is shown that the heating of cathodes on the basis of Y 2 O 3 and La 2 O 3 at activation temperatures during 2-3 h with successive cooling results in the state of surface with increased thermoemission activity. It is established that the cathode heating in electric field of positive polarity results in decreasing thermoemission activity of lanthanum oxide by approximately 0.35 eV and for yttrium oxide - by approximately 0.05 eV as compared with the heating in the field of negative polarity. The effect obtained is related to the change in the metal adatom concentration on the cathode surface

Long-term result of out-patient neodymium-doped yttrium aluminium garnet laser photocoagulation surgery for patients with epistaxis.

Science.gov (United States)

Zhang, J; Qiu, R; Wei, C

2016-01-01

To evaluate the long-term efficacy of out-patient neodymium-doped yttrium aluminium garnet laser photocoagulation surgery for patients with epistaxis. A retrospective clinical study was conducted. A total of 217 consecutive patients who presented with acute or recurrent epistaxis received neodymium-doped yttrium aluminium garnet laser photocoagulation treatment in an out-patient setting. At three years, 94 per cent of acute epistaxis patients versus 88 per cent of recurrent epistaxis patients reported no bleeding. The outcome scores at 12 weeks and 3 years after treatment showed no significant differences between the 2 groups (p = 0.207 and p = 0.186). However, there was a significant difference in outcome scores at four weeks after treatment (p = 0.034). The median (and mean ± standard deviation) pain levels experienced during the laser operation (performed in an office setting) were 4.0 (3.75 ± 2.09) in the acute epistaxis group and 4.0 (3.83 ± 2.01) in the recurrent epistaxis group. Neither group had any complications. Neodymium-doped yttrium aluminium garnet laser photocoagulation is desirable in the treatment of both acute and recurrent epistaxis, and has long-lasting efficacy.

Synthesis and characterization of titanium and yttrium precursors with unsaturated ligands: application to the doping of low-density micro-molecular materials oxides

International Nuclear Information System (INIS)

Gamet-Cauro, L.-C.

2001-01-01

The laser-matter interaction experiments for high-power pulsed lasers require doped micro-targets. The ablator is a Low-Density Microcellular Material,foam namely a styrene-divinylbenzene copolymer obtained by a HIPE process (High Internal Polymerisation Emulsion). The spectroscopic tracers selected for doping are titanium, yttrium and aluminium as oxides. For obtaining these hybrid organic-inorganic materials, precursors with polymerizable ligands were introduced during the emulsification step since the unsaturation of the ligands could participate in the copolymerization reaction. We report here in the synthesis and characterization of titanium and yttrium precursors with polymerizable ligands. The structures of [Ti(O i Pr) 3 (AMP)] 2 (HAMP allyl-methylphenol), [Ti(OEt) 3 (AAA)] 2 (HAAA allylacetoacetate), Y 8 O 2 (OH) 4 (OEt) 6 (AAA) 10 were established by X-ray diffraction. Ti 4 O 3 (OR) 8 (AAA) 2 (R Et, i Pr).[TiO(O i Pr)(oleate)] m , Y 4 (OH) 2 (AAA) 5 , Y 4 O(O i Pr) 5 (AAA) 5 , Y 4 (OH) 4 Cl 5 (AAA) 3 (THF) 3 have been prepared as well and characterized by FT-IR, 1 HNMR and elemental analysis. Micro-hydrolysis reactions of titanium derivatives were investigated. The rates of polymerisation and copolymerization with styrene were evaluated for the titanium precursors with polymerizable ligands. The parameters of the HIPE process were adapted to the fabrication of doped foams, only the dopant and initiator change. We discuss incorporation mechanisms of titanium oxide and yttrium oxo-hydroxides: precursor-surfactant interaction, copolymerization of precursors with unsaturated ligands and physical or chemical retention. The foams have been characterized by scanning electron microscopy (morphology), elemental analysis and fluorescence X cartography (amount, distribution of metal oxide), adsorption isotherms (BET, texture), compression tests (mechanical strength). Due to this systematic study, a good control of doping has become possible and allowed us to develop

Pharmacokinetics study of Zr-89-labeled melanin nanoparticle in iron-overload mice

International Nuclear Information System (INIS)

Zhang, Pengjun; Yue, Yuanyuan; Pan, Donghui; Yang, Runlin; Xu, Yuping; Wang, Lizhen; Yan, Junjie; Li, Xiaotian; Yang, Min

2016-01-01

Melanin, a natural biological pigment present in many organisms, has been found to exhibit multiple functions. An important property of melanin is its ability to chelate metal ions strongly, which might be developed as an iron chelator for iron overload therapy. Herein, we prepared the ultrasmall water-soluble melanin nanoparticle (MP) and firstly evaluate the pharmacokinetics of MP in iron-overload mice to provide scientific basis for treating iron-overload. To study the circulation time and biodistribution, MP was labeled with 89 Zr, a long half-life (78.4 h) positron-emitting metal which is suited for the labeling of nanoparticles and large bioactive molecule. MP was chelated with 89 Zr directly at pH 5, resulting in non-decay-corrected yield of 89.6% and a radiochemical purity of more than 98%. The specific activity was at least190 MBq/μmol. The 89 Zr-MP was stable in human plasma and PBS for at least 48 h. The half-life of 89 Zr-MP was about 15.70 ± 1.74 h in iron-overload mice. Biodistribution studies and MicroPET imaging showed that 89 Zr-MP mainly accumulated in liver and spleen, which are the target organ of iron-overload. The results indicate that the melanin nanoparticle is promising for further iron overload therapy.

29 CFR 1960.89 - Organization.

Science.gov (United States)

2010-07-01

... 29 Labor 9 2010-07-01 2010-07-01 false Organization. 1960.89 Section 1960.89 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR (CONTINUED... Field Federal Safety and Health Councils § 1960.89 Organization. (a) Field council officers shall...

Trends in metallo-organic chemistry of scandium, yttrium, and the lanthanides

International Nuclear Information System (INIS)

Singh, A.

1994-01-01

Several interesting aspects of the metallo-organic chemistry of group 3 and the lanthanides have been highlighted, which include: (a) the chemistry of a few notable organolanthanide compounds, alkoxo and aryloxo derivatives derived from sterically demanding ligands, (b) new trends in the chemistry of lanthanide heterometallic alkoxides, (c) an account of zero valent organometallics of yttrium and the lanthanides, and (d) aspects of agostic interactions in the lanthanide metallo-organic compounds. (author). 49 refs

Optimization of the personnel radiation protection during the treatment by antibodies labelled by yttrium 90

International Nuclear Information System (INIS)

Legrand, J.; Prangere, T.; Cougnenc, O.; Leleu, C.; Huglo, D.; Morschhauser, F.

2007-01-01

Beyond the acquired experience limiting the exposure time, measures of adequate radiation protection allow to reduce the doses of surface received to extremities by the personnel participating to the preparation of treatments by antibodies labelled by yttrium 90. (N.C.)

Thermoelectric Properties of the Yttrium-Doped Ceramic Oxide SrTiO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Khan, Tamal Tahsin; Ur, Soon-Chul [Korea National University of Transportation, Chungju (Korea, Republic of)

2017-01-15

The doping dependence of the thermoelectric figure of merit, ZT, of the ceramic oxide SrTiO{sub 3} at high temperature has been studied. In this study, yttrium was used as the doping element. A conventional solid-state reaction method was used for the preparation of Y-doped SrTiO{sub 3}. The doping level in SrTiO{sub 3} was controlled to be in the doping range of 2 - 10 mole%. Almost all the yttrium atoms incorporated into the SrTiO{sub 3} provided charge carriers, as was observed by using X-ray diffraction pattern. The relative densities of all the samples varied from 98.53% to 99.45%. The thermoelectric properties, including the electrical conductivity σ, Seebeck coefficient S, thermal conductivity k, and the figure of merit, ZT, were investigated at medium temperatures. The ZT value showed an obvious doping level dependence, in which a value as high as 0.18 is realized at 773 K for a doping of 8 mole%.

A study of the 89Y (n,n'γ)89Y reaction

International Nuclear Information System (INIS)

Nardelli, G.; Tornielli, G.

1985-01-01

Energy levels of 89 Y were populated by the 89 Y(n,n'γ) reaction at neutron energies between 2.2 and 4.8 MeV. A time gated (HP)Ge spectrometer was used to detect the deexcitation γ-rays. Forty-three levels through 4537 KeV excitation energy were identified in this way, two of which were previously unreported. Spins and parities were determined within the framework of the statistical theory from the angular distributions and excitation functions of the observed γ-rays. A complete level and decay scheme for 89 Y up to an excitation of 4.32 MeV is presented

Optical properties of Dy3+ doped yttrium aluminium borate

International Nuclear Information System (INIS)

Vazquez, R MartInez; Osellame, R; Marangoni, M; Ramponi, R; Dieguez, E; Ferrari, M; Mattarelli, M

2004-01-01

A Dy 3+ doped yttrium aluminium borate (Dy:YAB) crystal has been optically characterized. The refractive indices at seven different wavelengths, ranging from the visible to the near infrared (IR), have been measured and the Sellmeier curves have been calculated. The polarized optical absorption spectra have been obtained at room temperature, and the Judd-Ofelt parameters have been calculated. The lifetime of the upper laser level 4 F 9/2 has been estimated and compared with the experimental value. Evidence of high luminescence quantum efficiency of the 4 F 9/2 state in YAB is provided by measured lifetimes

14 CFR 151.89 - Roads.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Roads. 151.89 Section 151.89 Aeronautics... AID TO AIRPORTS Project Programming Standards § 151.89 Roads. (a) Federal-aid Airport Program funds may not be used to resolve highway problems. Only those airport entrance roads that are definitely...

Yttrium-enriched YBa2Cu3Ox thin films for coated conductors fabricated by pulsed laser deposition

International Nuclear Information System (INIS)

Khoryushin, Alexey V.; Mozhaev, Peter B.; Mozhaeva, Julia E.; Andersen, Niels H.; Grivel, Jean-Claude; Hansen, Jørn Bindslev; Jacobsen, Claus S.

2013-01-01

Highlights: ► YBCO films were fabricated by PLD from targets of various elemental compositions. ► The Y-enriched films contain yttria nanoparticles which provide efficient pinning. ► The best film has 5.5× higher j c (5 T,50 K) = 2.6MA/cm 2 comparing with a reference film. ► The Y-enriched films remain c-oriented up to 500 nm. ► Films demonstrate no j c suppression with thickness and remarkable stability with time. -- Abstract: The effects of excess yttria on the structural and electrical properties of the YBa 2 Cu 3 O x (YBCO) thin films are studied. The films were deposited on (LaAlO 3 ) 0.3 –(Sr 2 AlTaO 8 ) 0.7 substrates by pulsed laser ablation from targets with different elemental composition. An increase of yttrium content of the target leads to formation of porous films with significantly improved current-carrying capabilities. Structural studies of these films reveal presence of yttria nanoparticles embedded into the YBCO matrix. The highest obtained critical current density in an external magnetic field of 5 T was 2.6 MA/cm 2 at 50 K and 9.4 MA/cm 2 at 20 K. The fabricated Y-enriched YBCO films remain c-oriented at least up to 600 nm thickness with no significant suppression of the critical current density

Measurement of the depolarization in the elastic proton scattering on 1H, 27Al, and 89Y in the low energy range

International Nuclear Information System (INIS)

Schmitt, R.

1986-01-01

With the Erlangen QDQ magnetic spectrometer angular distributions of the depolarization in the elastic scattering of protons on 27 Al, 89 Y at 11 MeV and 1 H at 12 MeV were measured. The evaluation was performed for yttrium and aluminium by adding of additional terms in the optical model which regard the spin-spin interaction. The optical-model parameter without spin-spin potentials were stated by measurements of the cross section and the analyzing power in the 4π scattering chamber in Erlangen at several energies. The calculation of the depolarization which emerges because of the spin-spin interaction was performed by means of DWBA. The depolarization of the proton-proton scattering was evaluated by scattering-phase analysis. The fits were thereby performed on analyzing-power data. The electrical P-wave scattering phases resulted to δ 10 = 4.442±0.121, δ 11 = -2.515±0.026, and δ 12 = 0.937±0.038 (all in degrees). (orig./HSI) [de

40 CFR 89.206 - Trading.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Trading. 89.206 Section 89.206... EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Averaging, Banking, and Trading Provisions § 89.206 Trading. (a) Requirements for Tier 1 engines rated at or above 37 kW. (1) A nonroad...

40 CFR 89.205 - Banking.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Banking. 89.205 Section 89.205... EMISSIONS FROM NEW AND IN-USE NONROAD COMPRESSION-IGNITION ENGINES Averaging, Banking, and Trading Provisions § 89.205 Banking. (a) Requirements for Tier 1 engines rated at or above 37 kW. (1) A manufacturer...

Tunable negative index metamaterial using yttrium iron garnet

International Nuclear Information System (INIS)

He, Yongxue; He, Peng; Dae Yoon, Soack; Parimi, P.V.; Rachford, F.J.; Harris, V.G.; Vittoria, C.

2007-01-01

A magnetic field tunable, broadband, low-loss, negative refractive index metamaterial is fabricated using yttrium iron garnet (YIG) and a periodic array of copper wires. The tunability is demonstrated from 18 to 23 GHz under an applied magnetic field with a figure of merit of 4.2 GHz/kOe. The tuning bandwidth is measured to be 5 GHz compared to 0.9 GHz for fixed field. We measure a minimum insertion loss of 4 dB (or 5.7 dB/cm) at 22.3 GHz. The measured negative refractive index bandwidth is 0.9 GHz compared to 0.5 GHz calculated by the transfer function matrix theory and 1 GHz calculated by finite element simulation

RBS Characterization of Yttrium Iron Garnet Thin Films

International Nuclear Information System (INIS)

Roumie, M; Abdel samad, B.

2008-01-01

Magnetic materials such as yttrium iron garnet (YIG) are of great importance for its magneto-optic properties and for their potential applications in the domain of optical telecommunications. The deposition of thin films of YIG, on quartz or GGG (gadolinium gallium garnet) substrate, was performed using radio frequency non reactive magnetron sputtering, followed by high temperature annealing which is needed to enhance the crystallinity of the layers. Rutherford backscattering spectrometry RBS was used to determine the thickness and stoichiometry of the performed layers in order to investigate correlations between growth conditions and the quality of the final material. RBS measurements showed the influence of the deposition time and the temperature substrate on the film growth and its stoichiometry. (author)

Feasibility studies for production of {sup 89}Sr in the Fast Breeder Test Reactor (FBTR)

Energy Technology Data Exchange (ETDEWEB)

Saha, Debasish; Vithya, J.; Ashok Kumar, G.V.S.; Swaminathan, K.; Kumar, R.; Venkata Subramani, C.R.; Vasudeva Rao, P.R. [Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam (India). Fuel Chemistry Div.

2013-07-01

{sup 89}Sr, a pure beta emitter with half life of 50.53 d is used as its chloride solution for palliative care of bone metastases. This paper describes the feasibility studies that have been conducted at FBTR, IGCAR for production of this radionuclide using the {sup 89}Y(n, p){sup 89}Sr reaction. Yttria pellets were irradiated in a special subassembly at the core centre for a total of 73 d in two steps of 35 d and 38 d with a time gap of 38 d. The irradiated yttria target was dissolved in nitric acid and the bulk Y was separated by solvent extraction using the TBP-HNO{sub 3} complex. The {sup 89}Sr fraction was purified using the cation exchange resin DOWEX 50W x 8 (100-200 mesh size) from the other radioactive impurities seen. The eluted {sup 89}Sr fraction was assayed using a GM counting system. The {sup 89}Sr activity produced in 1 g of yttria pellet was found to be 19 mCi. (orig.)

Measurement of activation cross sections for quasi-monoenergetic neutron induced reactions of {sup 89}Y

Energy Technology Data Exchange (ETDEWEB)

Zaman, Muhammad; Kim, Guinyun; Kim, Kwangsoo; Nadeem, Muhammad [Kyungpook National University, Department of Physics and Center for High Energy Physics, Daegu (Korea, Republic of); Naik, Haladhara [Kyungpook National University, Department of Physics and Center for High Energy Physics, Daegu (Korea, Republic of); Bhabha Atomic Research Centre, Radiochemistry Division, Mumbai (India); Lee, Manwoo [Dongnam Inst. of Radiological and Medical Sciences, Research Center, Busan (Korea, Republic of)

2017-09-15

The neutron induced cross sections of the {sup 89}Y(n, 2n){sup 88}Y, {sup 89}Y(n, 3n){sup 87}Y and {sup 89}Y(n, 4n){sup 86}Y reactions were measured in the neutron energy range of 15.2 to 37.2 MeV by using an activation and off-line γ-ray spectrometric technique. The quasi-monoenergetic neutrons used for the above reactions are based on a {sup 9}Be(p, n) reaction. Simulations of the neutron spectra from the Be target were done using the MCNPX 2.6.0 program. Theoretical calculations were performed for the {sup 89}Y(n, 2n){sup 88}Y, {sup 89}Y(n, 3n){sup 87}Y and {sup 89}Y(n, 4n){sup 86}Y reaction cross sections using nuclear model code Talys 1.8. The measured and calculated cross sections were compared with the literature data given in EXFOR and the TENDL-2015 data libraries. The present data of the {sup 89}Y(n, xn) reaction were also compared with the similar data of the {sup 89}Y(γ, xn) reaction to examine the effect of the entrance channel parameters as well as the role of projectiles and ejectiles. (orig.)

Molecular-beam-deposited yttrium-oxide dielectrics in aluminum-gated metal - oxide - semiconductor field-effect transistors: Effective electron mobility

International Nuclear Information System (INIS)

Ragnarsson, L.-A degree.; Guha, S.; Copel, M.; Cartier, E.; Bojarczuk, N. A.; Karasinski, J.

2001-01-01

We report on high effective mobilities in yttrium-oxide-based n-channel metal - oxide - semiconductor field-effect transistors (MOSFETs) with aluminum gates. The yttrium oxide was grown in ultrahigh vacuum using a reactive atomic-beam-deposition system. Medium-energy ion-scattering studies indicate an oxide with an approximate composition of Y 2 O 3 on top of a thin layer of interfacial SiO 2 . The thickness of this interfacial oxide as well as the effective mobility are found to be dependent on the postgrowth anneal conditions. Optimum conditions result in mobilities approaching that of SiO 2 -based MOSFETs at higher fields with peak mobilities at approximately 210 cm 2 /Vs. [copyright] 2001 American Institute of Physics

Quantitative and Qualitative Assessment of Yttrium-90 PET/CT Imaging

OpenAIRE

Attarwala, Ali Asgar; Molina-Duran, Flavia; Büsing, Karen-Anett; Schönberg, Stefan O.; Bailey, Dale L.; Willowson, Kathy; Glatting, Gerhard

2014-01-01

Yttrium-90 is known to have a low positron emission decay of 32 ppm that may allow for personalized dosimetry of liver cancer therapy with (90)Y labeled microspheres. The aim of this work was to image and quantify (90)Y so that accurate predictions of the absorbed dose can be made. The measurements were performed within the QUEST study (University of Sydney, and Sirtex Medical, Australia). A NEMA IEC body phantom containing 6 fillable spheres (10-37 mm ∅) was used to measure the 90Y distribut...

Childhood acromegaly successfully treated with interstitial irradiation using Yttrium-90

International Nuclear Information System (INIS)

Rosenstock, J.; Doyle, F.H.; Mashiter, K.; Joplin, G.F.

1982-01-01

A child with a growth hormone producing tumour presented at the age of 4 1/2 years. The onset of the disease was at 18 months of age. Treatment was given with three doses of interstitial irradiation using yttrium-90 implants. There were no local complications from the procedures. Now, 11 years after diagnosis, she is asymptomatic, of normal appearance, and her height and the size of the pituitary fossa are normal. Growth hormone levels are almost normal, thyroid function is intact, and she is maintained on prednisone and sex hormones. (Authors)

Childhood acromegaly successfully treated with interstitial irradiation using Yttrium-90

Energy Technology Data Exchange (ETDEWEB)

Rosenstock, J.; Doyle, F.H.; Mashiter, K.; Joplin, G.F. (Royal Postgraduate Medical School, Hammersmith Hospital, London (UK). Dept. of Medicine and Radiology); Hall, R. (Royal Victoria Infirmary, Newcastle upon Tyne (UK))

1982-01-01

A child with a growth hormone producing tumour presented at the age of 4 1/2 years. The onset of the disease was at 18 months of age. Treatment was given with three doses of interstitial irradiation using Yttrium-90 implants. There were no local complications from the procedures. Now, 11 years after diagnosis, she is asymptomatic, of normal appearance, and her height and the size of the pituitary fossa are normal. Growth hormone levels are almost normal, thyroid function is intact, and she is maintained on prednisone and sex hormones.

Tattoo removal by Q-switched yttrium aluminium garnet laser: client satisfaction.

Science.gov (United States)

Hutton Carlsen, K; Esmann, J; Serup, J

2017-05-01

Tattoo removal by Q-switched yttrium aluminium garnet (YAG) lasers is golden standard; however, clients' satisfaction with treatment is little known. To determine clients' satisfaction with tattoo removal. One hundred and fifty-four tattoo removal clients who had attended the private clinic 'Centre for Laser Surgery', Hellerup, Denmark, from 2001 to 2013 completed a questionnaire concerning outcome expectations, level of pain experiences and satisfaction with tattoo removal. The laser surgeon and his team were blinded from data handling. The study design included a minimum 2-year postlaser treatment observation period from 2013 to 2015. Overall, clients were satisfied with their laser treatment; 85% assessed their treatment and results to be acceptable to superb, while 15% assessed their treatment and results to be inferior to unacceptable. Effectiveness relative to colour of tattoo on a scale from 0 (no effect) to 10 (complete removal) scored a mean of blue 9.5, black 9.4, yellow 8.9, red 8.8 and green 6.5. Clients were dissatisfied with green pigment remnants, which could mimic bruising. One hundred and twenty-nine clients (84%) experienced moderate to extreme pain during treatment. Twenty-eight (20%) developed minor scarring. There were many reasons for tattoo removal; e.g. stigmatisation (33%), conspicuousness (29%) and poor artistic quality (22%). One hundred and two clients had expected complete removal of tattoos without a blemish, expectations that were only partly fulfilled. During the treatment period, clients adjusted expectations and adapted more realistic views of outcomes. The majority of clients were satisfied with Q-switched YAG laser removal of tattoos despite high pretreatment expectations which were only partly met. The study supports YAG lasers for tattoo removal as acceptable therapy of today, with room for new approaches. © 2017 European Academy of Dermatology and Venereology.

Development of a liquid tin microjet target for an efficient laser-produced plasma extreme ultraviolet source

Science.gov (United States)

Higashiguchi, Takeshi; Hamada, Masaya; Kubodera, Shoichi

2007-03-01

A regenerative tin liquid microjet target was developed for a high average power extreme ultraviolet (EUV) source. The diameter of the target was smaller than 160 μm and good vacuum lower than 0.5 Pa was maintained during the operation. A maximum EUV conversion efficiency of 1.8% at the Nd:yttrium-aluminum-garnet laser intensity of around 2×1011 W/cm2 with a spot diameter of 175 μm (full width at half maximum) was observed. The angular distribution of the EUV emission remained almost isotropic, whereas suprathermal ions mainly emerged toward the target normal.

Development of a liquid tin microjet target for an efficient laser-produced plasma extreme ultraviolet source

International Nuclear Information System (INIS)

Higashiguchi, Takeshi; Hamada, Masaya; Kubodera, Shoichi

2007-01-01

A regenerative tin liquid microjet target was developed for a high average power extreme ultraviolet (EUV) source. The diameter of the target was smaller than 160 μm and good vacuum lower than 0.5 Pa was maintained during the operation. A maximum EUV conversion efficiency of 1.8% at the Nd:yttrium-aluminum-garnet laser intensity of around 2x10 11 W/cm 2 with a spot diameter of 175 μm (full width at half maximum) was observed. The angular distribution of the EUV emission remained almost isotropic, whereas suprathermal ions mainly emerged toward the target normal

Development of a liquid tin microjet target for an efficient laser-produced plasma extreme ultraviolet source.

Science.gov (United States)

Higashiguchi, Takeshi; Hamada, Masaya; Kubodera, Shoichi

2007-03-01

A regenerative tin liquid microjet target was developed for a high average power extreme ultraviolet (EUV) source. The diameter of the target was smaller than 160 microm and good vacuum lower than 0.5 Pa was maintained during the operation. A maximum EUV conversion efficiency of 1.8% at the Nd:yttrium-aluminum-garnet laser intensity of around 2 x 10(11) Wcm(2) with a spot diameter of 175 microm (full width at half maximum) was observed. The angular distribution of the EUV emission remained almost isotropic, whereas suprathermal ions mainly emerged toward the target normal.

Hydrogen Production from Cyclic Chemical Looping Steam Methane Reforming over Yttrium Promoted Ni/SBA-16 Oxygen Carrier

Directory of Open Access Journals (Sweden)

Sanaz Daneshmand-Jahromi

2017-09-01

Full Text Available In this work, the modification of Ni/SBA-16 oxygen carrier (OC with yttrium promoter is investigated. The yttrium promoted Ni-based oxygen carrier was synthesized via co-impregnation method and applied in chemical looping steam methane reforming (CL-SMR process, which is used for the production of clean energy carrier. The reaction temperature (500–750 °C, Y loading (2.5–7.4 wt. %, steam/carbon molar ratio (1–5, Ni loading (10–30 wt. % and life time of OCs over 16 cycles at 650 °C were studied to investigate and optimize the structure of OC and process temperature with maximizing average methane conversion and hydrogen production yield. The synthesized OCs were characterized by multiples techniques. The results of X-ray powder diffraction (XRD and energy dispersive X-ray spectroscopy (EDX of reacted OCs showed that the presence of Y particles on the surface of OCs reduces the coke formation. The smaller NiO species were found for the yttrium promoted OC and therefore the distribution of Ni particles was improved. The reduction-oxidation (redox results revealed that 25Ni-2.5Y/SBA-16 OC has the highest catalytic activity of about 99.83% average CH4 conversion and 85.34% H2 production yield at reduction temperature of 650 °C with the steam to carbon molar ratio of 2.

Reaction scheme of partial oxidation of methane to synthesis gas over yttrium-stabilized zirconia

NARCIS (Netherlands)

Zhu, J.J.; van Ommen, J.G.; Lefferts, Leonardus

2004-01-01

The partial oxidation of methane to synthesis gas over yttrium-stabilized zirconia (YSZ) was studied with in situ FTIR and both steady-state and transient experiments. The four major products, CO, H2, CO2, and H2O, are primary products of CPOM over YSZ. Besides these major products and traces of

Addition compounds of lanthamide (III) and yttrium (III) hexafluorophosphates and N,N - dimethylformamide

International Nuclear Information System (INIS)

Braga, L.S.P.

1983-01-01

Addition compounds of lanthanide (III) and yttrium (III) hexafluorophosphates and N-N-Dimetylformamide are described to characterize the complexes, elemental analysis, melting ranges, molar conductance measurements, X-ray powder patters infrared and Raman spectra, TG and DTA curves, are studied. Information concerning the decomposition of the adducts through the thermogravimetric curves and the differential thermal analysis curves is obtained. (M.J.C.) [pt

Characterization of photoluminescent europium doped yttrium oxide thin-films prepared by metallorganic chemical vapor deposition

International Nuclear Information System (INIS)

McKittrick, J.; Bacalski, C.F.; Hirata, G.A.; Hubbard, K.M.; Pattillo, S.G.; Salazar, K.V.; Trkula, M.

1998-01-01

Europium doped yttrium oxide, (Y 1-x Eu x ) 2 O 3 , thin-films were deposited on silicon and sapphire substrates by metallorganic chemical vapor deposition (MOCVD). The films were grown in a MOCVD chamber reacting yttrium and europium tris(2,2,6,6-tetramethyl-3,5,-heptanedionates) precursors in an oxygen atmosphere at low pressures (5 Torr) and low substrate temperatures (500--700 C). The films deposited at 500 C were flat and composed of nanocrystalline regions of cubic Y 2 O 3 , grown in a textured [100] or [110] orientation to the substrate surface. Films deposited at 600 C developed from the flat, nanocrystalline morphology into a plate-like growth morphology oriented in the [111] with increasing deposition time. Monoclinic Y 2 O 3 :Eu 3+ was observed in x-ray diffraction for deposition temperatures ≥600 C on both (111) Si and (001) sapphire substrates. This was also confirmed by the photoluminescent emission spectra

Structure-terahertz property relationship in yttrium aluminum garnet ceramics

Energy Technology Data Exchange (ETDEWEB)

Steere, D.W.; Clark, B.M.; Sundaram, S.K. [Alfred University, Terahertz and Millimeter Waves Laboratory (T-Lab), Kazuo Inamori School of Engineering, The New York State College of Ceramics, Alfred, NY (United States); Gaume, R. [Townes Laser Institute and the NanoScience Technology Center, CREOL, The College of Optics and Photonics, Orlando, FL (United States)

2017-08-15

Terahertz (THz) transmission measurements on chemically variant yttrium aluminum garnet (YAG) ceramics are described. Chemical compositions and processing parameters were varied to determine the effect of stoichiometry, density, and pore volume distribution on the optical and dielectric properties in the THz frequency regime. Density has the largest effect on properties out of the parameters that were investigated. In addition, a linear correlation between cubic root of real permittivity at 1 THz and average density of these samples is observed. Our results show promise for design and fabrication of advanced optical materials and devices with desired THz properties via controlling density and porosity of the materials. (orig.)

High-Performance Pyrochlore-Type Yttrium Ruthenate Electrocatalyst for Oxygen Evolution Reaction in Acidic Media

Energy Technology Data Exchange (ETDEWEB)

Kim, Jaemin [Department; Shih, Pei-Chieh [Department; Tsao, Kai-Chieh [Department; Pan, Yung-Tin [Department; Yin, Xi [Department; Sun, Cheng-Jun [X-ray; Yang, Hong [Department

2017-08-17

Development of acid-stable electrocatalysts with low overpotential for oxygen evolution reaction (OER) is a major challenge for the production of hydrogen directly from water. We report in this paper a pyrochlore yttrium ruthenate (Y2Ru2O7-δ) electrocatalyst that has significantly enhanced performance towards OER in acid media over the best-known catalysts, with an onset overpotential of 190 mV and high stability in 0.1-M perchloric acid solution. X-ray absorption near-edge structure (XANES) indicates Y2Ru2O7-δ electrocatalyst had a low valence state that favors the high OER activity. Density functional theory (DFT) calculation shows this pyrochlore has lower band center energy for the overlap between Ru 4d and O 2p orbitals and therefore more stable Ru-O bond than RuO2, highlighting the effect of yttrium on the enhancement in stability. The Y2Ru2O7-δ pyrochlore is also free of expensive iridium metal, thus a cost-effective candidate for practical applications.

Yttrium scandate thin film as alternative high-permittivity dielectric for germanium gate stack formation

Energy Technology Data Exchange (ETDEWEB)

Lu, Cimang, E-mail: cimang@adam.t.u-tokyo.ac.jp; Lee, Choong Hyun; Nishimura, Tomonori; Toriumi, Akira [Department of Materials Engineering, The University of Tokyo, 7-3-1 Hongo, Tokyo 113-8656 (Japan); JST, CREST, 7-3-1 Hongo, Tokyo 113-8656 (Japan)

2015-08-17

We investigated yttrium scandate (YScO{sub 3}) as an alternative high-permittivity (k) dielectric thin film for Ge gate stack formation. Significant enhancement of k-value is reported in YScO{sub 3} comparing to both of its binary compounds, Y{sub 2}O{sub 3} and Sc{sub 2}O{sub 3}, without any cost of interface properties. It suggests a feasible approach to a design of promising high-k dielectrics for Ge gate stack, namely, the formation of high-k ternary oxide out of two medium-k binary oxides. Aggressive scaling of equivalent oxide thickness (EOT) with promising interface properties is presented by using YScO{sub 3} as high-k dielectric and yttrium-doped GeO{sub 2} (Y-GeO{sub 2}) as interfacial layer, for a demonstration of high-k gate stack on Ge. In addition, we demonstrate Ge n-MOSFET performance showing the peak electron mobility over 1000 cm{sup 2}/V s in sub-nm EOT region by YScO{sub 3}/Y-GeO{sub 2}/Ge gate stack.

Process for making a titanium diboride-chromium diboride-yttrium titanium oxide ceramic composition

Science.gov (United States)

Holcombe, C.E.; Dykes, N.L.

1992-04-28

A ceramic composition is described. The ceramic composition consists essentially of from about 84 to 96 w/o titanium diboride, from about 1 to 9 w/o chromium diboride, and from about 3 to about 15 w/o yttrium-titanium-oxide. A method of making the ceramic composition is also described. The method of making the ceramic composition comprises the following steps: Step 1--A consolidated body containing stoichiometric quantities of titanium diboride and chromium diboride is provided. Step 2--The consolidated body is enclosed in and in contact with a thermally insulated package of yttria granules having a thickness of at least 0.5 inches. Step 3--The consolidated body enclosed in the thermally insulated package of yttria granules is heated in a microwave oven with microwave energy to a temperature equal to or greater than 1,900 degrees centigrade to sinter and uniformly disperse yttria particles having a size range from about 1 to about 12 microns throughout the consolidated body forming a densified body consisting essentially of titanium diboride, chromium diboride, and yttrium-titanium-oxide. The resulting densified body has enhanced fracture toughness and hardness. No Drawings

Separation of yttrium from strontium in the aqueous phase of the water/nitrobenzene extraction system

Czech Academy of Sciences Publication Activity Database

Vaňura, P.; Makrlík, E.; Vobecký, Miloslav

2003-01-01

Roč. 256, č. 1 (2003), s. 171-172 ISSN 0236-5731 R&D Projects: GA MŠk LN00B084 Institutional research plan: CEZ:AV0Z4031919; CEZ:MSM 230000009 Keywords : extraction * strontium * yttrium Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 0.472, year: 2003

Successful treatment of laser induced hypopigmentation with narrowband ultraviolet B targeted phototherapy

Directory of Open Access Journals (Sweden)

Venkataram Mysore

2013-01-01

Full Text Available Q-switched 1064 nm neodymium-doped yttrium aluminium garnet (Qs 1064 nm Nd: YAG laser plays an important role in the treatment of pigmentary skin disorders, including tattoos. Although it has high efficacy and safety, adverse effect like hypopigmentation may occur causing anxiety to patients. We present a case report of Qs 1064 nm Nd: YAG laser induced hypopigmentation which was successfully treated with ultraviolet B targeted phototherapy, with rapid and satisfactory re-pigmentation.

PSMA-Targeted Polygadolinium Clusters: A Novel Agent for Imaging Prostate Cancer

National Research Council Canada - National Science Library

Messerle, Louis

2007-01-01

Controlled hydrolysis of lanthanide element or yttrium salts in the presence of aminoacids yields a series of polynuclear clusters with two, four, twelve, fourteen, and fifteen lanthanide or yttrium...

Effect of surface composition of yttrium-stabilized zirconia on partial oxidation of methane to synthesis gas.

NARCIS (Netherlands)

Zhu, J.J.; van Ommen, J.G.; Knoester, A.; Lefferts, Leonardus

2005-01-01

Catalytic partial oxidation of methane to synthesis gas (CPOM) over yttrium-stabilized zirconia (YSZ) was studied within a wide temperature window (500¿1100 °C). The catalysts were characterized by X-ray fluorescence (XRF) and low-energy ion scattering (LEIS). The influence of calcination

Thermodynamic Functions of Yttrium Trifluoride and Its Dimer in the Gas Phase

Science.gov (United States)

Osina, E. L.; Kovtun, D. M.

2018-05-01

New calculations of the functions for YF3 and Y2F6 in the gas phase using quantum-chemical calculations by MP2 and CCSD(T) methods are performed in connection with the ongoing work on obtaining reliable thermodynamic data of yttrium halides. The obtained values are entered in the database of the IVTANTERMO software complex. Equations approximating the temperature dependence of the reduced Gibbs energy in the T = 298.15-6000 K range of temperatures are presented.

14 CFR 33.89 - Operation test.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Operation test. 33.89 Section 33.89... STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.89 Operation test. (a) The operation test must include testing found necessary by the Administrator to demonstrate— (1) Starting, idling...

A study of the dynamics of hydrogen in yttrium using inelastic neutron scattering

Energy Technology Data Exchange (ETDEWEB)

Bennington, S M; Benham, M J; Ross, D K [Birmingham Univ. (UK). School of Physics and Space Research; Taylor, A D; Bowden, Z A [Rutherford Appleton Lab., Chilton (UK)

1989-01-01

The results of several high resolution inelastic scattering experiments on {alpha}-phase yttrium-hydrogen are presented including measurements of energy levels up to the fourth and a study of the splitting of certain states due to hydrogen-hydrogen interactions. An attempt is made to model the energy levels by using perturbed simple harmonic oscillator wavefunctions. This can account for most of the major features of the spectrum. (orig.).

Influence of radiant heating treatments on fusion of high-temperature superconducting yttrium ceramics; Vliyanie termoradiatsionnykh obrabotok na sintez vysokotempiraturnykh sverkhprovodyaschikh ittrievykh keramik

Energy Technology Data Exchange (ETDEWEB)

Bitenbaev, M I; Polyakov, A I [Inst. Yadernoj Fiziki Natsionalnogo Yadernogo Tsentra Respubliki Kazakhstan, Almaty (Kazakhstan)

1999-07-01

Regardless of the fact that the materials made of HTSC-ceramics are promising, there is no any information about their successful practical application in publications. To our opinion, it is explained by the fact, first of all, that the conservative technologies of the powder metallurgy do not allow producing HTSC systems with excellent operating performance (structure homogeneity, long-term stability of Sc properties and etc.). This report presents outcomes of experiments on fusion of yttrium ceramics containing raw components irradiated by g-rays {sup 60}Co under the temperature exceeding 500 degrees C. HTSC properties of ceramics were studied according to their differential spectra of radio-frequency (RF) field absorption. The RF absorption spectrum of yttrium ceramics samples produced according to conservative technology is sufficiently permitted triplet with the Sc transition temperatures range of 80 K, 90 K, 95 K. Irradiation under the increased temperatures and mechanical limitation allow producing samples of yttrium HTSC-ceramics with sufficient homogeneous structure and superconducting properties that are stable to air conditions for not less than one year.

Tungsten - Yttrium Based Nuclear Structural Materials

Science.gov (United States)

Ramana, Chintalapalle; Chessa, Jack; Martinenz, Gustavo

2013-04-01

The challenging problem currently facing the nuclear science community in this 21st century is design and development of novel structural materials, which will have an impact on the next-generation nuclear reactors. The materials available at present include reduced activation ferritic/martensitic steels, dispersion strengthened reduced activation ferritic steels, and vanadium- or tungsten-based alloys. These materials exhibit one or more specific problems, which are either intrinsic or caused by reactors. This work is focussed towards tungsten-yttrium (W-Y) based alloys and oxide ceramics, which can be utilized in nuclear applications. The goal is to derive a fundamental scientific understanding of W-Y-based materials. In collaboration with University of Califonia -- Davis, the project is designated to demonstrate the W-Y based alloys, ceramics and composites with enhanced physical, mechanical, thermo-chemical properties and higher radiation resistance. Efforts are focussed on understanding the microstructure, manipulating materials behavior under charged-particle and neutron irradiation, and create a knowledge database of defects, elemental diffusion/segregation, and defect trapping along grain boundaries and interfaces. Preliminary results will be discussed.

7 CFR 301.89-1 - Definitions.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Definitions. 301.89-1 Section 301.89-1 Agriculture..., DEPARTMENT OF AGRICULTURE DOMESTIC QUARANTINE NOTICES Karnal Bunt § 301.89-1 Definitions. Actual price... part) for or capable of propagation, including a tree, a tissue culture, a plantlet culture, pollen, a...

49 CFR 89.45 - Department determination.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Department determination. 89.45 Section 89.45... Referral of Debts to IRS for Tax Refund Offset § 89.45 Department determination. (a) Following review of... supporting rationale. (b) If the Department either sustains or amends its determination, it shall notify the...

7 CFR 993.89 - Effective time.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Effective time. 993.89 Section 993.89 Agriculture... Order Regulating Handling Miscellaneous Provisions § 993.89 Effective time. The provisions of this subpart, as well as any amendments to this subpart, shall become effective at such time as the Secretary...

49 CFR 230.89 - Reverse gear.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Reverse gear. 230.89 Section 230.89 Transportation... Reversing Gear § 230.89 Reverse gear. (a) General provisions. Reverse gear, reverse levers, and quadrants... quadrant. Proper counterbalance shall be provided for the valve gear. (b) Air-operated power reverse gear...

7 CFR 160.89 - Medicinal preparations.

Science.gov (United States)

2010-01-01

... 7 Agriculture 3 2010-01-01 2010-01-01 false Medicinal preparations. 160.89 Section 160.89... STANDARDS FOR NAVAL STORES Sales and Shipments § 160.89 Medicinal preparations. A compound or mixture containing spirits of turpentine or rosin, or both, with other drugs, when sold for medicinal purposes, is...

89Zr-huJ591 immuno-PET imaging in patients with advanced metastatic prostate cancer

International Nuclear Information System (INIS)

Pandit-Taskar, Neeta; Solomon, Stephen B.; Durack, Jeremy C.; Carrasquillo, Jorge A.; Lefkowitz, Robert A.; Osborne, Joseph R.; O'Donoghue, Joseph A.; Beylergil, Volkan; Ruan, Shutian; Cheal, Sarah M.; Lyashchenko, Serge; Gonen, Mithat; Lewis, Jason S.; Holland, Jason P.; Reuter, Victor E.; Loda, Massimo F.; Smith-Jones, Peter M.; Weber, Wolfgang A.; Larson, Steven M.; Bander, Neil H.; Scher, Howard I.; Morris, Michael J.

2014-01-01

Given the bone tropism of prostate cancer, conventional imaging modalities poorly identify or quantify metastatic disease. 89 Zr-huJ591 positron emission tomography (PET) imaging was performed in patients with metastatic prostate cancer to analyze and validate this as an imaging biomarker for metastatic disease. The purpose of this initial study was to assess safety, biodistribution, normal organ dosimetry, and optimal imaging time post-injection for lesion detection. Ten patients with metastatic prostate cancer received 5 mCi of 89 Zr-huJ591. Four whole-body scans with multiple whole-body count rate measurements and serum activity concentration measurements were obtained in all patients. Biodistribution, clearance, and lesion uptake by 89 Zr-huJ591 immuno-PET imaging was analyzed and dosimetry was estimated using MIRD techniques. Initial assessment of lesion targeting of 89 Zr-huJ591 was done. Optimal time for imaging post-injection was determined. The dose was well tolerated with mild chills and rigors seen in two patients. The clearance of 89 Zr-huJ591 from serum was bi-exponential with biological half-lives of 7 ± 4.5 h (range 1.1-14 h) and 62 ± 13 h (range 51-89 h) for initial rapid and later slow phase. Whole-body biological clearance was 219 ± 48 h (range 153-317 h). The mean whole-body and liver residence time was 78.7 and 25.6 h, respectively. Dosimetric estimates to critical organs included liver 7.7 ± 1.5 cGy/mCi, renal cortex 3.5 ± 0.4 cGy/mCi, and bone marrow 1.2 ± 0.2 cGy/mCi. Optimal time for patient imaging after injection was 7 ± 1 days. Lesion targeting of bone or soft tissue was seen in all patients. Biopsies were performed in 8 patients for a total 12 lesions, all of which were histologically confirmed as metastatic prostate cancer. One biopsy-proven lesion was not positive on 89 Zr-huJ591, while the remaining 11 lesions were 89 Zr-huJ591 positive. Two biopsy-positive nodal lesions were noted only on 89 Zr-huJ591 study, while the

Ultrasonic and viscometric studies of yttrium soaps in mixed organic solvents

International Nuclear Information System (INIS)

Mehrotra, K.N.; Tandon, K.; Rawat, M.K.

1992-01-01

The ultrasonic and viscosity measurements of yttrium soaps (caprylate, caprate and laurate) in a mixture of benzene and dimethyl formamide (3:2) have been carried out with a view to determine the critical micellar concentration soap-solvent interaction and other allied parameters. The various acoustic parameters (intermolecular free-length adiabatic compressibility, apparent molar compressibility, specific acoustic impedance, molar sound velocity, solvation number available volume and relative association) have been evaluated by ultrasonic velocity measurements. The results of viscosity measurement have been explained in terms of well known equations. (author). 18 refs., 2 figs., 3 tabs

Thermoanalytical, spectroscopic and DFT studies of heavy trivalent lanthanides and yttrium(III) with oxamate as ligand

Energy Technology Data Exchange (ETDEWEB)

Caires, Flavio Junior; Gaglieri, Caroline, E-mail: caires.flavio@fc.unesp.br [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Bauru, SP (Brazil). Faculdade de Ciencias; Nunes, Wilhan Donizete Goncalves; Nascimento, Andre Luiz Carneiro Soares do; Teixeira, Jose Augusto; Zangaro, Georgia Alvim Coelho; Treu-Filho, Oswaldo; Ionashiro, Massao [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, SP (Brazil)

2017-07-15

Solid-state LnL{sub 3}∙nH{sub 2}O complexes, where Ln stands for trivalent lanthanides (Tb to Lu) or yttrium(III) and L is oxamate (NH{sub 2}COCO{sub 2}{sup -}), have been synthesized. The characterization of the complexes was performed by using elemental analysis (EA), complexometric titration with EDTA, thermoanalytical techniques such as simultaneous thermogravimetry and differential scanning calorimetry (TG-DSC), evolved gas analysis (TG-FTIR), infrared spectroscopy (IR) and powder X-ray diffraction (XRPD). The results provided information about thermal behavior, crystallinity, stoichiometry, coordination sites, as well as the products released during thermal degradation of the complexes studied. Theoretical calculation of yttrium oxamate, as representative of all complexes was performed using density functional theory (DFT) for studying the molecular structure and vibrational spectrum of the investigated molecule in the ground state. The optimized geometrical parameters and theoretical vibrational spectrum obtained by DFT calculations are in good agreement with the experimental results. (author)

Industrial precipitation of yttrium chloride and zirconyl chloride: Effect of pH on ceramic properties for yttria partially stabilised zirconia

International Nuclear Information System (INIS)

Carter, G.A.; Hart, R.D.; Rowles, M.; Ogden, M.I.; Buckley, C.E.

2009-01-01

Two 3 mol% partially stabilised zirconia (P-SZ) samples suitable for the SOFC market were manufactured from solutions through to ceramics using a method similar to a known industrial process. The only difference in preparation of the two 3 mol% P-SZ samples was the pH of precipitation which was set at pH 3 or 12. Particle size measurements by dynamic light scattering were used to characterise the precipitate and the filtration rates were investigated. Five point N 2 -BET was used to investigate the specific surface area before and after calcination with the response to temperature tracked. Similarly TGA/DTA investigation was used to determine the calcination point during all of these tests and it was found that both powders behaved similarly. XRD-Rietveld analysis incorporating in situ and ex situ calcination revealed that the pH 3 sample had more monoclinic phase present after calcination and sintering as a ceramic. Ceramic testing incorporating hardness (Vickers), toughness (K 1C ), MOR, density and grain sizing was carried out, all determined that the material produced at pH 12 was superior for SOFC applications than the pH 3 sample. Further investigation using TEM-EDS revealed that the processing of the pH 3 powder had allowed a lower concentration of the yttrium which was incorporated at approximately 2 mol% instead of the required 3. ICP-OES of the after filter liquor indicated that high concentrations of yttrium (797 ppm) were found in the solution with the wash solution having 149 ppm yttrium. In contrast the pH 12 samples had 7 ppm in both the after filter liquor and wash indicating that the yttrium is bound within the matrix more completely at the higher pH.

Determination of strontium-90 from direct separation of yttrium-90 by solid phase extraction using DGA Resin for seawater monitoring.

Science.gov (United States)

Tazoe, Hirofumi; Obata, Hajime; Yamagata, Takeyasu; Karube, Zin'ichi; Nagai, Hisao; Yamada, Masatoshi

2016-05-15

It is important for public safety to monitor strontium-90 in aquatic environments in the vicinity of nuclear related facilities. Strontium-90 concentrations in seawater exceeding the background level have been observed in accidents of nuclear facilities. However, the analytical procedure for measuring strontium-90 in seawater is highly demanding. Here we show a simple and high throughput analytical technique for the determination of strontium-90 in seawater samples using a direct yttrium-90 separation. The DGA Resin is used to determine the abundance of strontium-90 by detecting yttrium-90 decay (beta-emission) in secular equilibrium. The DGA Resin can selectively collect yttrium-90 and remove naturally occurring radionuclides such as (40)K, (210)Pb, (214)Bi, (238)U, and (232)Th and anthropogenic radionuclides such as (140)Ba, and (140)La. Through a sample separation procedure, a high chemical yield of yttrium-90 was achieved at 95.5±2.3%. The result of IAEA-443 certified seawater analysis (107.7±3.4 mBq kg(-1)) was in good agreement with the certified value (110±5 mBq kg(-1)). By developed method, we can finish analyzing 8 samples per day after achieving secular equilibrium, which is a reasonably fast throughput in actual seawater monitoring. By processing 3 L of seawater sample and applying a counting time of 20 h, minimum detectable activity can be as low as 1.5 mBq kg(-1), which could be applied to monitoring for the contaminated marine environment. Reproducibility was found to be 3.4% according to 10 independent analyses of natural seawater samples from the vicinity of the Fukushima Daiichi Nuclear Power Plant in September 2013. Copyright © 2016 Elsevier B.V. All rights reserved.

Annotating STEAP1 regulation in prostate cancer with 89Zr immuno-PET.

Science.gov (United States)

Doran, Michael G; Watson, Philip A; Cheal, Sarah M; Spratt, Daniel E; Wongvipat, John; Steckler, Jeffrey M; Carrasquillo, Jorge A; Evans, Michael J; Lewis, Jason S

2014-12-01

Antibodies and antibody-drug conjugates targeting the cell surface protein 6 transmembrane epithelial antigen of prostate 1 (STEAP1) are in early clinical development for the treatment of castration-resistant prostate cancer (PCa). In general, antigen expression directly affects the bioactivity of therapeutic antibodies, and the biologic regulation of STEAP1 is unusually complicated in PCa. Paradoxically, STEAP1 can be induced or repressed by the androgen receptor (AR) in different human PCa models, while also expressed in AR-null PCa. Consequently, there is an urgent need to translate diagnostic strategies to establish which regulatory mechanism predominates in patients to situate the appropriate therapy within standard of care therapies inhibiting AR. To this end, we prepared and evaluated (89)Zr-labeled MSTP2109A ((89)Zr-2109A), a radiotracer for PET derived from a fully humanized monoclonal antibody to STEAP1 in preclinical PCa models. (89)Zr-2109A specifically localized to the STEAP1-positive human PCa models CWR22Pc, 22Rv1, and PC3. Moreover, (89)Zr-2109A sensitively measured treatment-induced changes (∼66% decline) in STEAP1 expression in CWR22PC in vitro and in vivo, a model we showed to express STEAP1 in an AR-dependent manner. These findings highlight the ability of immuno-PET with (89)Zr-2109A to detect acute changes in STEAP1 expression and argue for an expansion of ongoing efforts to image PCa patients with (89)Zr-2109A to maximize the clinical benefit associated with antibodies or antibody-drug conjugates to STEAP1. © 2014 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

21 CFR 1250.89 - Swimming pools.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Swimming pools. 1250.89 Section 1250.89 Food and... SANITATION Sanitation Facilities and Conditions on Vessels § 1250.89 Swimming pools. (a) Fill and draw swimming pools shall not be installed or used. (b) Swimming pools of the recirculation type shall be...

Microstructure and tensile properties of yttrium nitride dispersion-strengthened 14Cr–3W ferritic steels

Energy Technology Data Exchange (ETDEWEB)

Huang, Liqing [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); School of Mechanical and Mining Engineering, University of Queensland, Brisbane 4067, QLD (Australia); Liu, Zuming, E-mail: lzm@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Chen, Shiqi; Guo, Yang [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2015-12-15

Highlights: • Innovative nano yttrium nitride dispersion strengthened steels were fabricated. • Higher content of additives accelerate the steel-ceramic powder milling process more. • Steel with high content (3%) of YN dispersoids can obtain good performance at 500 °C. - Abstract: 14Cr–3W ferritic steel powders were mechanically milled with microscale yttrium nitride (YN) particles to fabricate particle dispersion-strengthened ferritic steels. After hot consolidation and annealing, the steel matrix was homogeneously dispersed with nano-scale YN particles. The steel containing 0.3 wt.% YN particles exhibited a yield strength of 1445 MPa at room temperature. Its total elongation was 10.3%, and the fracture surface exhibited mixed ductile and quasi-cleavage fracture morphologies. The steel with a much higher content of YN particles (3 wt.%) in its matrix was much stronger (1652 MPa) at room temperature at the cost of ductility. In particular, it exhibited a high yield strength (1350 MPa) with applicable ductility (total elongation > 10%) at 500 °C. This study has developed a new kind of reinforcement particle to fabricate high-performance ferritic steels.

Use of Yttrium-90 TheraSphere for the treatment of unresectable hepatocellular carcinoma.

Science.gov (United States)

Liu, Michael D; Uaje, Michelle B; Al-Ghazi, Muthana S; Fields, Denise; Herman, June; Kuo, Jeffrey V; Milne, Norah; Nguyen, Thong H; Ramsinghani, Nilam S; Tokita, Kenneth M; Tsai, Fong Y; Vajgrt, Duane J; Imagawa, David K

2004-11-01

This is a retrospective analysis of a new treatment modality, intra-arterial administration of Yttrium-90 TheraSphere, for unresectable hepatocellular carcinoma (HCC). Patients with HCC not amenable to surgical treatment who had satisfactory physiological function without comorbid disease or significant pulmonary shunting were eligible for treatment. Patients were categorized into complete, partial, or no response based on serum alpha-fetoprotein (AFP) levels and CT or MRI imaging. Fourteen patients were considered candidates for treatment. Three patients were excluded due to significant hepatopulmonary shunting. Eleven patients were treated with TheraSphere. One patient (9%) had a complete response, eight patients (78%) had a partial response, and two patients (18%) showed no response. Partial and complete responders with AFP-associated HCC demonstrated a median decrease in AFP levels of 79 per cent at 73 days. No patients developed liver toxicity nor died due to treatment. Five patients (45%) died of progressive disease at a median of 7 months post-treatment. Six patients (54%) were alive at a median of 11 months (range, 9 to 20 months). Okuda stage 2 and 3 patients showed a median survival of 11 months and 7 months, respectively. Yttrium-90 TheraSphere treatment for unresectable hepatocellular carcinoma is well tolerated and appears to extend survival.

10 CFR 1040.89-6 - Mediation.

Science.gov (United States)

2010-01-01

... 10 Energy 4 2010-01-01 2010-01-01 false Mediation. 1040.89-6 Section 1040.89-6 Energy DEPARTMENT... Enforcement Procedures § 1040.89-6 Mediation. (a) Referral of complaints for mediation. DOE will refer to the Federal Mediation and Conciliation Service, in accordance with 45 CFR 90.43(c)(3), all complaints that: (1...

Few-MeV neutrons incident on yttrium

International Nuclear Information System (INIS)

Budtz-Jorgensen, C.; Guenther, P.; Smith, A.; Whalen, J.

1982-09-01

Neutron total and scattering cross sections of elemental yttrium are measured in the few-MeV region with broad resolutions. The total-cross section measurements extend from approx. = 0.5 to 4.2 MeV in steps of less than or equal to 0.1 MeV. Neutron elastic- and inelastic-scattering cross sections are measured from approx. = 1.5 to 4.0 MeV, at incident-neutron energy intervals of less than or equal to 50 keV and at ten or more scattering angles distributed between 20 and 160 deg. Inelastically-scattered neutron groups are observed corresponding to the excitation of levels at 909 +- 23, 1504 +- 20, 1747 +- 16, 2224 +- 16, 2567 +- 26, 2889 +- 12 and 3104 +- 10 keV. The experimental results are discussed in terms of the spherical optical-statistical, coupled-channels and core-coupling models and compared with corresponding quantities given in the evaluated nuclear data file ENDF/B-V

Preparation and characterization of Yttrium-Aluminium garnet (Y3Al5O12)

International Nuclear Information System (INIS)

Ruzicka, J.; Niznansky, D.; Houzvicka, J.; Nikl, M.; Cerny, R.

2009-01-01

This work deals with the preparation of powders and transparent yttrium aluminium garnet (Y 3 Al 5 O 12 - YAG) from nanopowders. Stoichiometric amounts of nanocrystalline Al 2 O 3 and Y 2 O 3 were mixed and chemically pretreated using different basic agents and using ultrasonic bath. Resulting mixture was dried, pressed and heated up to 1750°C. Final material was characterized by X-ray diffraction, DTA and optical and electron microscopy

Seven up. The incorporation of Li{sup +} cations in yttrium tungstate and silicate tungstate

Energy Technology Data Exchange (ETDEWEB)

Dorn, Katharina V.; Schustereit, Tanja; Strobel, Sabine; Hartenbach, Ingo [Institute for Inorganic Chemistry, University of Stuttgart (Germany)

2017-12-13

Lithium yttrium(III) oxidotungstate(VI), LiY{sub 5}W{sub 8}O{sub 32}, was synthesized by solid-state reaction of a mixture of lithium chloride, yttrium sesquioxide, and tungsten trioxide. It crystallizes monoclinically in space group C2/c (a = 1908.34(5) pm, b = 561.80(1) pm, c = 1147.22(3) pm, β = 111.255(2) , Z = 2). The structure comprises one mixed Li{sup +}/Y{sup 3+} cationic position (molar ratio Li:Y1 = 1:1) and one cationic position exclusively occupied by Y{sup 3+} cations. All W{sup 6+} cations are surrounded by six O{sup 2-} anions, forming distorted octahedral coordination polyhedra, which are mutually linked by both edges and vertices to cascaded {sup 2}{sub ∞}{[W_4O_1_6]"8"-} layers. Lithium yttrium(III) oxidosilicate(IV) oxidotungstate(VI), LiY{sub 5}[SiO{sub 4}]{sub 2}[WO{sub 4}]{sub 4}, was obtained as by-product in the synthesis of YF[WO{sub 4}] by sintering a mixture of Y{sub 2}O{sub 3}, YF{sub 3}, and WO{sub 3} with lithium chloride as fluxing agent in sealed silica ampoules. It crystallizes orthorhombically in space group Pban (a = 512.08(4) pm, b = 1673.35(12) pm, c = 493.68(4) pm, Z = 1) bearing one mixed crystallographic position occupied by Li{sup +} and Y{sup 3+} cations in a molar ratio of 1:3 and one exclusive Y{sup 3+} position in its structure. The coordination polyhedra around the Si{sup 4+} and W{sup 6+} cations are isolated tetrahedra built up by four O{sup 2-} anions each. The crystal structure of this silicate tungstate can be derived from the scheelite-type structure by inserting anionic {sup 2}{sub ∞}{(Y2[SiO_4])"-} layers between cationic {sup 2}{sub ∞}{[(Li/Y1)_2[WO_4]_2]"+} double layers. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Calorimetric investigation of an yttrium-dysprosium spin glass

International Nuclear Information System (INIS)

Wenger, L.E.

1978-01-01

In an effort to compare the spin glass characteristics of yttrium--rare earth alloys with those of the noble-metal spin glasses, the susceptibility and heat capacity of Y/sub 0.98/Dy/sub 0.02/ have been measured in the temperature range 2.5--40 K. The low-field ac susceptibility measurement shows the characteristic cusp-like peak at 7.64 K. The magnetic specific heat of the same sample shows a peak at 7.0 K and may be qualitatively described as a semi-cusp. The magnetic entropy change from absolute zero to 7 K is approximately 0.52 of cR ln(2J+1). These results are qualitatively different than previous calorimetric results on the archetypal spin glasses, AuFe and CuMn, where rounded maxima are observed at temperatures above the spin glass transition temperatures

A divalent rare earth oxide semiconductor: Yttrium monoxide

Energy Technology Data Exchange (ETDEWEB)

Kaminaga, Kenichi; Sei, Ryosuke [Department of Chemistry, The University of Tokyo, Tokyo 113-0033 (Japan); Department of Chemistry, Tohoku University, Sendai 980-8578 (Japan); Hayashi, Kouichi [Department of Environmental and Materials Engineering, Nagoya Institute of Technology, Nagoya 466-8555 (Japan); Happo, Naohisa [School of Information Sciences, Hiroshima City University, Hiroshima 731-3194 (Japan); Tajiri, Hiroo [Japan Synchrotron Radiation Research Institute (JASRI)/SPring-8, Sayo 679-5198 (Japan); Oka, Daichi; Fukumura, Tomoteru, E-mail: tomoteru.fukumura.e4@tohoku.ac.jp [Department of Chemistry, Tohoku University, Sendai 980-8578 (Japan); Hasegawa, Tetsuya [Department of Chemistry, The University of Tokyo, Tokyo 113-0033 (Japan)

2016-03-21

Rare earth oxides are usually widegap insulators like Y{sub 2}O{sub 3} with closed shell trivalent rare earth ions. In this study, solid phase rock salt structure yttrium monoxide, YO, with unusual valence of Y{sup 2+} (4d{sup 1}) was synthesized in a form of epitaxial thin film by pulsed laser deposition method. YO has been recognized as gaseous phase in previous studies. In contrast with Y{sub 2}O{sub 3}, YO was dark-brown colored and narrow gap semiconductor. The tunable electrical conductivity ranging from 10{sup −1} to 10{sup 3} Ω{sup −1 }cm{sup −1} was attributed to the presence of oxygen vacancies serving as electron donor. Weak antilocalization behavior observed in magnetoresistance indicated significant role of spin-orbit coupling as a manifestation of 4d electron carrier.

Thermal conductivity of yttrium iron garnet at low temperatures

International Nuclear Information System (INIS)

Joshi, Y.P.; Sing, D.P.

1979-01-01

An analysis of the low-temperature thermal conductivity of yttrium iron garnet is presented giving consideration to the fact that in a conventional conductivity experiment the magnon temperature gradient inside a magnetic insulator need not be necessarily equal to the phonon temperature gradient. Consequently the effective conductivity can be less than the algebraic sum of the phonon and magnon intrinsic conductivities, depending on the magnon-phonon thermal relaxation rate. This relaxation rate has been distinguished from the individual phonon and magnon relaxation rates and an expression is derived for it. Theoretical calculations of the effective conductivity are found to be in good agreement with experimental results. The contribution of magnons to the effective conductivity is observed to be small at all temperatures below the conductivity maximum. (author)

9 CFR 89.4 - Watering.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Watering. 89.4 Section 89.4 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS STATEMENT OF POLICY UNDER THE TWENTY-EIGHT HOUR...

Solid-phase synthesis of yttrium ferrites with structures of perovskite and garnet

Energy Technology Data Exchange (ETDEWEB)

Tkachenko, E V; Shapovalov, A G; Aksel' rod, N L; Pazdnikov, I P [Ural' skij Gosudarstvennyj Univ., Sverdlovsk (USSR)

1980-09-01

The solid phase synthesis of yttrium ferrites having a perovskite- and garnet-like structure has been investigated in the temperature range from 800 to 1500 deg C and temper times of up to 80 hours by reaction zone simulation and magnetic phase analysis. It is shown that for conversion degrees d<0.15 the reactions are diffusion-controlled. The rate constants and effective diffusion in the formation of YFeO/sub 3/ and Y/sub 3/Fe/sub 5/O/sub 12/ have been determined.

{sup 89}Zr-huJ591 immuno-PET imaging in patients with advanced metastatic prostate cancer

Energy Technology Data Exchange (ETDEWEB)

Pandit-Taskar, Neeta; Solomon, Stephen B.; Durack, Jeremy C.; Carrasquillo, Jorge A.; Lefkowitz, Robert A.; Osborne, Joseph R. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Weill Cornell Medical College, Department of Radiology, New York, NY (United States); O' Donoghue, Joseph A. [Memorial Sloan Kettering Cancer Center, Department of Medical Physics, New York, NY (United States); Beylergil, Volkan; Ruan, Shutian; Cheal, Sarah M. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Lyashchenko, Serge [Memorial Sloan Kettering Cancer Center, Department of Radiochemistry and Molecular Imaging Probes Core, New York, NY (United States); Gonen, Mithat [Memorial Sloan Kettering Cancer Center, Department of Epidemiology and Biostatistics, New York, NY (United States); Lewis, Jason S. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Memorial Sloan Kettering Cancer Center, Department of Radiochemistry and Molecular Imaging Probes Core, New York, NY (United States); Memorial Sloan Kettering Cancer Center, Program in Molecular Pharmacology and Chemistry, New York, NY (United States); Weill Cornell Medical College, Department of Radiology, New York, NY (United States); Holland, Jason P. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Harvard Medical School, Department of Radiology of Massachusetts General Hospital, Boston, MA (United States); Reuter, Victor E. [Memorial Sloan Kettering Cancer Center, Department of Pathology, New York, NY (United States); Weill Cornell Medical College, Department of Pathology, New York, NY (United States); Loda, Massimo F. [Dana-Farber Cancer Institute, Boston, MA (United States); Broad Institute of Harvard and MIT, Cambridge, MA (United States); Smith-Jones, Peter M. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Department of Psychiatry and Behavioral Science of Stony Brook University, Stony Brook, NY (United States); Weber, Wolfgang A.; Larson, Steven M. [Memorial Sloan Kettering Cancer Center, Department of Radiology, New York, NY (United States); Memorial Sloan Kettering Cancer Center, Program in Molecular Pharmacology and Chemistry, New York, NY (United States); Weill Cornell Medical College, Department of Radiology, New York, NY (United States); Bander, Neil H. [Memorial Sloan Kettering Cancer Center, Department of Surgery, New York, NY (United States); Weill Cornell Medical College, Department of Urology, New York, NY (United States); Scher, Howard I.; Morris, Michael J. [Memorial Sloan Kettering Cancer Center, Department of Medicine, New York, NY (United States); Weill Cornell Medical College, Department of Medicine, New York, NY (United States)

2014-11-15

Given the bone tropism of prostate cancer, conventional imaging modalities poorly identify or quantify metastatic disease. {sup 89}Zr-huJ591 positron emission tomography (PET) imaging was performed in patients with metastatic prostate cancer to analyze and validate this as an imaging biomarker for metastatic disease. The purpose of this initial study was to assess safety, biodistribution, normal organ dosimetry, and optimal imaging time post-injection for lesion detection. Ten patients with metastatic prostate cancer received 5 mCi of {sup 89}Zr-huJ591. Four whole-body scans with multiple whole-body count rate measurements and serum activity concentration measurements were obtained in all patients. Biodistribution, clearance, and lesion uptake by {sup 89}Zr-huJ591 immuno-PET imaging was analyzed and dosimetry was estimated using MIRD techniques. Initial assessment of lesion targeting of {sup 89}Zr-huJ591 was done. Optimal time for imaging post-injection was determined. The dose was well tolerated with mild chills and rigors seen in two patients. The clearance of {sup 89}Zr-huJ591 from serum was bi-exponential with biological half-lives of 7 ± 4.5 h (range 1.1-14 h) and 62 ± 13 h (range 51-89 h) for initial rapid and later slow phase. Whole-body biological clearance was 219 ± 48 h (range 153-317 h). The mean whole-body and liver residence time was 78.7 and 25.6 h, respectively. Dosimetric estimates to critical organs included liver 7.7 ± 1.5 cGy/mCi, renal cortex 3.5 ± 0.4 cGy/mCi, and bone marrow 1.2 ± 0.2 cGy/mCi. Optimal time for patient imaging after injection was 7 ± 1 days. Lesion targeting of bone or soft tissue was seen in all patients. Biopsies were performed in 8 patients for a total 12 lesions, all of which were histologically confirmed as metastatic prostate cancer. One biopsy-proven lesion was not positive on {sup 89}Zr-huJ591, while the remaining 11 lesions were {sup 89}Zr-huJ591 positive. Two biopsy-positive nodal lesions were noted only on

Erbium-doped yttrium aluminium garnet ablative laser treatment for endogenous ochronosis.

Science.gov (United States)

Chaptini, Cassandra; Huilgol, Shyamala C

2015-08-01

Ochronosis is a rare disease characterised clinically by bluish-grey skin discolouration and histologically by yellow-brown pigment deposits in the dermis. It occurs in endogenous and exogenous forms. Endogenous ochronosis, also known as alkaptonuria, is an autosomal recessive disease of tyrosine metabolism, resulting in the accumulation and deposition of homogentisic acid in connective tissue. We report a case of facial endogenous ochronosis and coexistent photodamage, which was successfully treated with erbium-doped yttrium aluminium garnet laser resurfacing and deep focal point treatment to remove areas of residual deep pigment. © 2014 The Australasian College of Dermatologists.

Hot Corrosion of Yttrium Stabilized Zirconia Coatings Deposited by Air Plasma Spray on a Nickel-Based Superalloy

Science.gov (United States)

Vallejo, N. Diaz; Sanchez, O.; Caicedo, J. C.; Aperador, W.; Zambrano, G.

In this research, the electrochemical impedance spectroscopy (EIS) and Tafel analysis were utilized to study the hot corrosion performance at 700∘C of air plasma-sprayed (APS) yttria-stabilized zirconia (YSZ) coatings with a NiCrAlY bond coat grown by high velocity oxygen fuel spraying (HVOF), deposited on an INCONEL 625 substrate, in contact with corrosive solids salts as vanadium pentoxide V2O5 and sodium sulfate Na2SO4. The EIS data were interpreted based on proposed equivalent electrical circuits using a suitable fitting procedure performed with Echem AnalystTM Software. Phase transformations and microstructural development were examined using X-ray diffraction (XRD), with Rietveld refinement for quantitative phase analysis, scanning electron microscopy (SEM) was used to determinate the coating morphology and corrosion products. The XRD analysis indicated that the reaction between sodium vanadate (NaVO3) and yttrium oxide (Y2O3) produces yttrium vanadate (YVO4) and leads to the transformation from tetragonal to monoclinic zirconia phase.

Hydrothermal synthesis of Yttrium Orthovanadate (YVO4) and its application in photo catalytic degradation of sewage water

International Nuclear Information System (INIS)

Komal, J. K.; Karimi, P.; Hui, K. S.

2010-01-01

In this paper; YVO 4 powder was successfully synthesized from Vanadium Pentaoxide (V 2 O 5 ), Yttrium Oxide (Y 2 O 3 ) and ethyl acetate as a mineralizer by hydrothermal method at a low temperature (T=.230 d egree C , and P=100 bars). The as-prepared powders were characterized by X-ray Diffraction, Fourier Transform Infrared Spectroscopy, Scanning Electron Microscopy, UV-V Spectroscopy and Chemical Oxygen Demand of the sewage water, respectively. The results show that hydrothermal method can greatly promote the crystallization and growth of YVO 4 phase. X-ray Diffraction pattern clearly indicates the tetragonal structure and crystallinity. An fourier transform infrared spectrum of the YVO 4 shows the presence of Y-O and V-O bond, respectively. The presence of these two peaks indicates that yttrium vanadate has been formed. UV-V is absorption spectra suggesting that YVO 4 particles have stronger UV absorption than natural sunlight and subsequent photo catalytic degradation data also confirmed their higher photo catalytic activity.

The effect of the purity and of the materials used for adapters on the purification of yttrium by solid state electrotransport

International Nuclear Information System (INIS)

Nikoforova, T.V.; Volkov, V.T.

1986-01-01

The influence of tantalum, molybdenum and zirconium adapters on the efficiency of the solid state electrotransport process is investigated with a view to increasing the quality and purity of yttrium. The degree and direction of metallic impurity electromigration in the given metals were studied. The impurities in question were shown to move in different directions depending on the type of adapter. Recommendations for the application of adapters according to their purity are given. The application of high purity tantalum as anode and cathode adapters in three-stage solid state electrotransport enabled us to obtain yttrium single crystals with a ratio of resistance at room temperature to that at helium temperatures of 1200. (orig.)

Microstructural evolution and tensile mechanical properties of thixoformed AZ91D magnesium alloy with the addition of yttrium

International Nuclear Information System (INIS)

Zhao Zude; Chen Qiang; Kang Feng; Shu Dayu

2009-01-01

The microstructure evolution of AZ91D magnesium alloy in the semi-solid state has been proposed or reported in previous literature. However, no detailed investigation has been conducted regarding the relationship between the microstructure and tensile mechanical properties of the thixoformed AZ91D magnesium alloy. In this paper, the microstructure of AZ91D alloy with the addition of yttrium was produced by the semi-solid thermal transformation (SSTT) route and the strain-induced melt activation (SIMA) route, respectively. Isothermal holding experiments investigated grain coarsening and the degree of spheroidization as a function of holding time in the semi-solid state. The SSTT route and the SIMA route were used to obtain the semi-solid feedstock for thixoforming. The results show that solid particles of the SSTT alloy are spheroidized to some extent but the previous irregular shape is still obvious in some of them. While the SIMA alloy exhibits ideal, fine microstructure, in which completely spheroidized solid particles contain little entrapped liquid. The microstructure of the SSTT alloy is less spheroidized compared with the SIMA alloy under the similar isothermal holding condition. As the holding time increases, the mean solid particle size of the SSTT alloy decreases initially, then increases, while the mean solid particle size of the SIMA alloy increases monotonously at 560 deg. C. Compared with the SSTT alloy, the SIMA alloy obtains finer grains under the similar isothermal holding condition. The mechanical properties of the thixoformed AZ91D alloy with the addition of yttrium produced by the SIMA route are better than those of the thixoformed alloy produced by the SSTT route. The ultimate tensile strength, yield strength and elongation for the thixoformed alloy produced by the SIMA route are 303.1 MPa, 147.6 MPa and 13.27%, respectively. The tensile properties for the AZ91D alloy with the addition of yttrium thixoformed from starting material produced by

Implantation of titanium, chromium, yttrium, molybdenum, silver, hafnium, tantalum, tungsten and platinum ions generated by a metal vapor vacuum ion source into 440C stainless steel

International Nuclear Information System (INIS)

Sasaki, Jun; Hayashi, Kazunori; Sugiyama, Kenji; Ichiko, Osami; Hashiguchi, Yoshihiro

1992-01-01

Titanium, yttrium, molybdenum, silver, chromium, hafnium, tantalum, tungsten and platinum ions generated by a metal vapor vacuum arc (MEVVA) ion source were implanted into 440C stainless steel in the dose region 10 17 ions cm -2 with extraction voltages of up to 70 kV. Glow discharge spectroscopy (GDS), friction coefficient, and Vickers microhardness of the specimens were studied. Grooves made by friction tests were investigated by electron probe microanalysis (EPMA). GDS showed incorporation of carbon in the yttrium, hafnium, tantalum, tungsten and platinum implanted specimens, as well as titanium implanted samples. A large amount of oxygen was observed in the yttrium implanted specimen. The friction coefficient was measured by reciprocating sliding of an unimplanted 440C ball without lubricant at a load of 0.245 N. The friction decreased and achieved a stable state after implantation of titanium, hafnium and tantalum. The friction coefficient of the platinum implanted specimen showed a gradual decrease after several cycles of sliding at high friction coefficient. The yttrium implanted sample exhibited a decreased but slightly unstable friction coefficient. Results from EPMA showed that the implanted elements, which gave decreased friction, remained even after sliding of 200 cycles. Implantation of chromium, molybdenum, silver and tungsten did not provide a decrease in friction and the implants were gone from the wear grooves after the sliding tests. (orig.)

Half-life measurement of 89Rb

International Nuclear Information System (INIS)

Guo Xiaoqing; Yuan Daqing; Xu Lijun; Chen Kesheng; Wu Yongle; Zheng Yanming; Yao Shunhe

2013-01-01

89 Rb is an important fission product used for monitoring possible release of fission products from fuel element. The half-life is one of important nuclear parameters. The half-life of 89 Rb was determined using reference source method with two sets of HPGe detectors by place-relay way. In reference source method, the ratio of net full- energy peak areas from the measure nuclide and the reference source was used to avoid the count correction caused by dead time and pileup. For the very short half-life of 89 Rb, the half-life iterative method was used in data analysis and the translation method was used in data unification. Finally, the measured half-life of 89 Rb is (14.41±0.04) min. (authors)

Stability constants of mixed ligand complexes of lanthanide(III) and yttrium(III) with complexone and substituted salicylic acids

International Nuclear Information System (INIS)

Kolhe, Vishnu; Dwivedi, K.

1996-01-01

Salicylic acid and substituted salicylic acids are potential antimicrobial agents. Binary complexes of salicylic acid and its substituted derivatives with lanthanide(III) and yttrium(III) metal ions have been reported. There are reports on the ternary metal complexing equilibria with some lanthanide(III) and yttrium(III) metal ions involving aminopolycarboxylic acid as one ligand and salicylic acid (SA) and other related compounds as the second ligands. Ethylene glycol bis(2-aminoethylether)- N, N, N', N'-tetraacetic acid (EGTA) is an important member of aminopolycarboxylic acid and finds many applications in medicine and biology. Recently, few ternary complexes have been reported using EGTA as ligand. In view of biological importance of simple and mixed ligand complexes EGTA, SA and DNSA (3,5-dinitrosalicylic acid), a systematic study has been undertaken for the determination of stability constant and the results are reported. (author). 6 refs., 1 fig., 2 tabs

Surface characterization of low-temperature grown yttrium oxide

Science.gov (United States)

Krawczyk, Mirosław; Lisowski, Wojciech; Pisarek, Marcin; Nikiforow, Kostiantyn; Jablonski, Aleksander

2018-04-01

The step-by-step growth of yttrium oxide layer was controlled in situ using X-ray photoelectron spectroscopy (XPS). The O/Y atomic concentration (AC) ratio in the surface layer of finally oxidized Y substrate was found to be equal to 1.48. The as-grown yttrium oxide layers were then analyzed ex situ using combination of Auger electron spectroscopy (AES), elastic-peak electron spectroscopy (EPES) and scanning electron microscopy (SEM) in order to characterize their surface chemical composition, electron transport phenomena and surface morphology. Prior to EPES measurements, the Y oxide surface was pre-sputtered by 3 kV argon ions, and the resulting AES-derived composition was found to be Y0.383O0.465C0.152 (O/Y AC ratio of 1.21). The SEM images revealed different surface morphology of sample before and after Ar sputtering. The oxide precipitates were observed on the top of un-sputtered Y oxide layer, whereas the oxide growth at the Ar ion-sputtered surface proceeded along defects lines normal to the layer plane. The inelastic mean free path (IMFP) characterizing electron transport was evaluated as a function of energy in the range of 0.5-2 keV from the EPES method. Two reference materials (Ni and Au) were used in these measurements. Experimental IMFPs determined for the Y0.383O0.465C0.152 and Y2O3 surface compositions, λ, were uncorrected for surface excitations and approximated by the simple function λ = kEp at electron energies E between 500 eV and 2000 eV, where k and p were fitted parameters. These values were also compared with IMFPs resulting from the TPP-2 M predictive equation for both oxide compositions. The fitted functions were found to be reasonably consistent with the measured and predicted IMFPs. In both cases, the average value of the mean percentage deviation from the fits varied between 5% and 37%. The IMFPs measured for Y0.383O0.465C0.152 surface composition were found to be similar to the IMFPs for Y2O3.

Radio-synoviorthesis with yttrium 90 in the knee-joint in rheumatoid arthritis

International Nuclear Information System (INIS)

Hagena, F.W.; Muenchen Univ.

1982-01-01

The radio-synoviorthesis with yttrium 90 in the knee-joint in rheumatoid arthritis was performed and controlled in 106 knees of patients with rheumatoid arthritis over a span of time between 6 and 49 months. The results are similar to those of other authors. As compared to synovectomy radio-synoviorthesis seems less successful as far as long-term results are concerned. As local treatment radio-synoviorthesis seems a good supplementory element in the therapeutic plan of rheumatoid arthritis. The indication to alternative procedures has been considered carefully for each individual case and joint. (orig.) [de

Yttrium-90 radioembolization of hepatocellular carcinoma and metastatic disease to the liver.

Science.gov (United States)

Lewandowski, Robert J; Salem, Riad

2006-03-01

Yttrium-90 ((90)Y) radioembolization is a catheter-based therapy that delivers internal radiation to hepatic tumors in the form of microspheres. (90)Y can be delivered to the hepatic tumor as either a constituent of a glass microsphere, TheraSphere(®), or as a biocompatible resin-based microsphere, SIR-Spheres(®). Once embedded within the tumor microcirculation, these microspheres emit β-radiation at therapeutic levels. While the technical aspects of radioembolization are quite complex, the collective clinical experience presented in the literature supports the use of (90)Y radioembolization for unresectable hepatic malignancies.

Studies on Characterization, Optical Absorption, and Photoluminescence of Yttrium Doped ZnS Nanoparticles

Directory of Open Access Journals (Sweden)

Ranganaik Viswanath

2014-01-01

Full Text Available Pure ZnS and ZnS:Y nanoparticles were synthesized by a chemical coprecipitation route using EDTA-ethylenediamine as a stabilizing agent. X-ray diffraction (XRD, high resolution transmission electron microscopy (HRTEM, field emission scanning electron microscopy (FE-SEM, Fourier transform infrared spectrometry (FTIR, thermogravimetric-differential scanning calorimetry (TG-DSC, and UV-visible and photoluminescence (PL spectroscopy were employed to characterize the as-synthesized ZnS and ZnS:Y nanoparticles, respectively. XRD and TEM studies show the formation of cubic ZnS:Y particles with an average size of ~4.5 nm. The doping did not alter the phase of the zinc sulphide, as a result the sample showed cubic zincblende structure. The UV-visible spectra of ZnS and ZnS:Y nanoparticles showed a band gap energy value, 3.85 eV and 3.73 eV, which corresponds to a semiconductor material. A luminescence characteristics such as strong and stable visible-light emissions in the orange region alone with the blue emission peaks were observed for doped ZnS nanoparticles at room temperature. The PL intensity of orange emission peak was found to be increased with an increase in yttrium ions concentration by suppressing blue emission peaks. These results strongly propose that yttrium doped zinc sulphide nanoparticles form a new class of luminescent material.

Targets and teamwork

DEFF Research Database (Denmark)

Skinner, Timothy C.; Lange, Karin S.; Hoey, Hilary

2017-01-01

differences in mean HbA1c between centers ranging from 7.3±0.8% (53mmol/mol±8.7) to 8.9±1.1% (74mmol/mol±12.0). Centers with lower mean HbA1c had (1) parents who reported lower targets for their children, (2) health-care professionals that reported lower targets and more frequent testing, and (3) teams...

Comparison of the air oxidation behaviors of Zircaloy-4 implanted with yttrium and cerium ions at 500 deg. C

International Nuclear Information System (INIS)

Chen, X.W.; Bai, X.D.; Xu, J.; Zhou, Q.G.; Chen, B.S.

2002-01-01

As a valuable process for surface modification of materials, ion implantation is eminent to improve mechanical properties, electrochemical corrosion resistance and oxidation behaviors of varieties of materials. To investigate and compare the oxidation behaviors of Zircaloy-4, implantation of yttrium ion and cerium ion were respectively employed by using an MEVVA source at the energy of 40 keV with a dose ranging from 1x10 16 to 1x10 17 ions/cm 2 . Subsequently, weight gain curves of the different specimens including as-received Zircaloy-4 and Zircaloy-4 specimens implanted with the different ions were measured after oxidation in air at 500 deg. C for 100 min. It was obviously found that a significant improvement was achieved in the oxidation behaviors of implanted Zircaloy-4 compared with that of the as-received Zircaloy-4, and the oxidation behavior of cerium-implanted Zircaloy-4 was somewhat better than that of yttrium-implanted specimen. To obtain the valence and the composition of the oxides in the scale, X-ray photoemission spectroscopy was used in the present study. Glancing angle X-ray diffraction, employed to analyze the phase transformation in the oxide films, showed that the addition of yttrium transformed the phase from monoclinic zirconia to tetragonal zirconia, yet the addition of cerium transformed the phase from monoclinic zirconia to hexagonal zirconia. In the end, the mechanism of the improvement of the oxidation behavior was discussed

7 CFR 301.89-2 - Regulated articles.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Regulated articles. 301.89-2 Section 301.89-2... SERVICE, DEPARTMENT OF AGRICULTURE DOMESTIC QUARANTINE NOTICES Karnal Bunt § 301.89-2 Regulated articles. The following are regulated articles: (a) Conveyances, including trucks, railroad cars, and other...

ICP-MS determination of rare earth elements, yttrium, uranium and thorium in niobium-tantalum rich samples

International Nuclear Information System (INIS)

Sunilkumar, Beena; Padmasubashini, V.

2013-01-01

ICP-MS is a powerful and extremely sensitive technique which has been applied successfully for the determination of REEs in diverse geological samples. In the present work, ICP-MS has been applied for the rapid determination of REEs, yttrium as well as uranium and thorium in niobium and tantalum rich samples, using a fluoride fusion method for sample dissolution

Profile of yttrium segregation in BaCe0,9Y0,1O3-δ as function of sintering temperature

International Nuclear Information System (INIS)

Hosken, C.M.; Souza, D.P.F. de

2010-01-01

Researches on solid oxide fuel cells indicate barium cerate perovskite as a very attractive material for using as electrolyte due to its high protonic conductivity. The objective of this work is investigate the yttrium segregation during sintering of BaCe 0,9 Y 0,1 O 3-δ doped with Zn O as a sintering aid. The powders were prepared by citrate process. Powders were isostatic pressed into pellets and sintered in air at 1200, 1275, 1325 and 1400 deg C. The samples were characterized by scanning electron microscopy, X-ray diffraction and impedance spectroscopy. Secondary phase containing Yttrium and Cerium was detected as sintering temperature increased. Increase of the lattice parameter and activation energy for electrical conductivity were also detected on samples sintered at 1400 deg C. (author)

40 CFR 89.406 - Pre-test procedures.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Pre-test procedures. 89.406 Section 89.406 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... Procedures § 89.406 Pre-test procedures. (a) Allow a minimum of 30 minutes warmup in the standby or operating...

Mechanical properties of lanthanum and yttrium chromites

Energy Technology Data Exchange (ETDEWEB)

Paulik, S.W.; Armstrong, T.R. [Pacific Northwest National Lab., Richland, WA (United States)

1996-12-31

In an operating high-temperature (1000{degrees}C) solid oxide fuel cell (SOFC), the interconnect separates the fuel (P(O{sub 2}){approx}10{sup -16} atm) and the oxidant (P(O2){approx}10{sup 0.2} atm), while being electrically conductive and connecting the cells in series. Such severe atmospheric and thermal demands greatly reduce the number of viable candidate materials. Only two materials, acceptor substituted lanthanum chromite and yttrium chromite, meet these severe requirements. In acceptor substituted chromites (Sr{sup 2+} or Ca{sup 2+} for La{sup 3+}), charge compensation is primarily electronic in oxidizing conditions (through the formation of Cr{sup 4+}). Under reducing conditions, ionic charge compensation becomes significant as the lattice becomes oxygen deficient. The formation of oxygen vacancies is accompanied by the reduction of Cr{sup 4+} ions to Cr{sup 3+} and a resultant lattice expansion. The lattice expansion observed in large chemical potential gradients is not desirable and has been found to result in greatly reduced mechanical strength.

Neutron scattering study of yttrium iron garnet

Science.gov (United States)

Shamoto, Shin-ichi; Ito, Takashi U.; Onishi, Hiroaki; Yamauchi, Hiroki; Inamura, Yasuhiro; Matsuura, Masato; Akatsu, Mitsuhiro; Kodama, Katsuaki; Nakao, Akiko; Moyoshi, Taketo; Munakata, Koji; Ohhara, Takashi; Nakamura, Mitsutaka; Ohira-Kawamura, Seiko; Nemoto, Yuichi; Shibata, Kaoru

2018-02-01

The nuclear and magnetic structure and full magnon dispersions of yttrium iron garnet Y3Fe5O12 have been studied using neutron scattering. The refined nuclear structure is distorted to a trigonal space group of R 3 ¯ . The highest-energy dispersion extends up to 86 meV. The observed dispersions are reproduced by a simple model with three nearest-neighbor-exchange integrals between 16 a (octahedral) and 24 d (tetrahedral) sites, Ja a, Ja d, and Jd d, which are estimated to be 0.00 ±0.05 , -2.90 ±0.07 , and -0.35 ±0.08 meV, respectively. The lowest-energy dispersion below 14 meV exhibits a quadratic dispersion as expected from ferromagnetic magnons. The imaginary part of q -integrated dynamical spin susceptibility χ″(E ) exhibits a square-root energy dependence at low energies. The magnon density of state is estimated from χ″(E ) obtained on an absolute scale. The value is consistent with the single chirality mode for the magnon branch expected theoretically.

ELECTRON MICROSCOPIC INVESTIGATION OF YTTRIUM ALUMINUM GARNET POWDERS Y3AL5O12, SYNTHESIZED BY SOL–GEL METHOD

Directory of Open Access Journals (Sweden)

A. E. Baranchikov

2015-09-01

Full Text Available Subject of Study. The paper presents results of characterization for neodymium doped yttrium aluminum garnet nanopowders - YAG:Nd3+ by the method of scanning electronic microscopy. Method. Synthesis of YAG:Nd3+ was carried out by sol-gel method from nitrate or acetate - nitrate solutions with addition of some organic compounds and ammonia as well. Such substances were used as the source ones: oxides of neodymium and yttrium with the content of the basic substance equal to 99.999 %; organic compounds: citric acid with the content of the basic substance not less than 99.0 %; ethylene glycol (99.5%; the ammonium lauryl sulfate (99.0 %; urea (99.0 % of Alfa Aesar, Fluka, Aldrich companies. Oxides of yttrium and neodymium (5 at. % were dissolved in 50% acetic acid, nitrate aluminum was added with a view to the resulting product Y2,85Nd0,15Al5,0O12, the solution was stirred and heated to 60С before reaching its transparency and uniformity. The weight of the portion corresponding to the stoichiometry YAG was 2.0 g. 50 % aqueous solutions of organic substances or 5% NH4OH in a weight ratio of 1:1 to the weight of the garnet were added in aqueous solutions, placed into glass cups. The solutions were thoroughly mixed first using a conventional stirrer, then on ultrasonic installation with simultaneous 60 С heating for 2 hours. Drying of solutions to the consistency of a powder or a thick gel was carried out at 110 С. Then the samples were placed into platinum cups and annealed in a tube furnace at 950 - 1050 С for the period from 0.5 to 2 hours. Additional annealing of the powders in the air at 950 - 1060С were carried out for the purpose of powders clarifying for residual amorphous carbon removal. Main Results. The synthesized powder precursors and powders after annealing were examined using a polarizing microscope to identify anisotropic crystalline phases. X-ray analysis of the synthesized samples was carried out on a DRON - 4 and UDR - 63

1 CFR 8.9 - Form of citation.

Science.gov (United States)

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Form of citation. 8.9 Section 8.9 General Provisions ADMINISTRATIVE COMMITTEE OF THE FEDERAL REGISTER SPECIAL EDITIONS OF THE FEDERAL REGISTER CODE OF FEDERAL REGULATIONS § 8.9 Form of citation. The Code of Federal Regulations may be cited by title and...

Processes leading to yttrium-barium cuprates formation in synthesis using nitrates

International Nuclear Information System (INIS)

Kulakov, A.B.; Tesker, A.M.; Zalishchanskij, M.E.; Tret'yakov, Yu.D.; Gipius, A.A.

1989-01-01

An attempt to determine sequence and conditions for transformations occuring at heating both of mechanical mixture of copper, yttrium and barium nitrates and salt product of sublimated dehydration of quick frozen solution of nitrates in question of correlation which corresponds to YBa 2 Cu 3 O 7-σ final compounds is made. It is shown that unlike individual nitrates their thermolysis in the mixture occurs at lower temperatures with mechanism variation of decomposition separate stages. Specimens of superconducting ceramics with 4.3 g/cm 3 density phase composition and oxygen content which correspond to YBa 2 Cu 3 O 6.85±0.05 formula are obtaied

Evidence of dilute ferromagnetism in rare-earth doped yttrium aluminium garnet

Energy Technology Data Exchange (ETDEWEB)

Farr, Warrick G.; Goryachev, Maxim; Le Floch, Jean-Michel; Tobar, Michael E. [ARC Centre of Excellence for Engineered Quantum Systems, University of Western Australia, 35 Stirling Highway, Crawley, Western Australia 6009 (Australia); Bushev, Pavel [Experimentalphysik, Universität des Saarlandes, D-66123 Saarbrücken (Germany)

2015-09-21

This work demonstrates strong coupling regime between an erbium ion spin ensemble and microwave hybrid cavity-whispering gallery modes in a yttrium aluminium garnet dielectric crystal. Coupling strengths of 220 MHz and mode quality factors in excess of 10{sup 6} are demonstrated. Moreover, the magnetic response of high-Q modes demonstrates behaviour which is unusual for paramagnetic systems. This behaviour includes hysteresis and memory effects. Such qualitative change of the system's magnetic field response is interpreted as a phase transition of rare earth ion impurities. This phenomenon is similar to the phenomenon of dilute ferromagnetism in semiconductors. The clear temperature dependence of the phenomenon is demonstrated.

Thermal effects from modified endodontic laser tips used in the apical third of root canals with erbium-doped yttrium aluminium garnet and erbium, chromium-doped yttrium scandium gallium garnet lasers.

Science.gov (United States)

George, Roy; Walsh, Laurence J

2010-04-01

To evaluate the temperature changes occurring on the apical third of root surfaces when erbium-doped yttrium aluminium garnet (Er:YAG) and erbium, chromium-doped yttrium scandium gallium garnet (Er,Cr:YSGG) laser energy was delivered with a tube etched, laterally emitting conical tip and a conventional bare design optical fiber tip. Thermal effects of root canal laser treatments on periodontal ligament cells and alveolar bone are of concern in terms of safety. A total of 64 single-rooted extracted teeth were prepared 1 mm short of the working length using rotary nickel-titanium Pro-Taper files to an apical size corresponding to a F5 Pro-Taper instrument. A thermocouple located 2 mm from the apex was used to record temperature changes arising from delivery of laser energy through laterally emitting conical tips or plain tips, using an Er:YAG or Er,Cr:YSGG laser. For the Er:YAG and Er,Cr:YSGG systems, conical fibers showed greater lateral emissions (452 + 69% and 443 + 64%) and corresponding lower forward emissions (48 + 5% and 49 + 5%) than conventional plain-fiber tips. All four combinations of laser system and fiber design elicited temperature increases less than 2.5 degrees C during lasing. The use of water irrigation attenuated completely the thermal effects of individual lasing cycles. Laterally emitting conical fiber tips can be used safely under defined conditions for intracanal irradiation without harmful thermal effects on the periodontal apparatus.

Determination of radioactive strontium in seawater

International Nuclear Information System (INIS)

Grahek, Zeljko; Rozmaric Macefat, Martina

2005-01-01

This paper describes the procedures of isolating strontium and yttrium from seawater that enable the determination of 89,90 Sr. In one procedure, strontium is directly isolated from seawater on the column filled with Sr resin by binding of strontium to the resin from 3 M HNO 3 in a seawater, and successive elution with HNO 3 . In others, strontium is precipitated from seawater with (NH 4 ) 2 CO 3 , followed by isolation on a Sr column or an anion exchange column. It is shown that strontium precipitation is optimal with concentration of 0.3 M (NH 4 ) 2 CO 3 at pH = 11. In these conditions, 100% Y, 78% Sr, 80% Ca and 50% Mg are precipitated. Strontium is bound on to Sr column from 5 to 8 M HNO 3 , separated from other elements by elution with 3 M HNO 3 and 0.05 M HNO 3 . Strontium and yttrium are bound on to anion exchange column from alcoholic solutions of nitric acid. The optimum mixture of alcohols for sample binding is a mixture of ethanol and methanol with the volume ratio 1:3. Strontium and yttrium are separated from Mg, Ca, K, and other elements by elution with 0.25 M HNO 3 in the mixture of ethanol and methanol. After the separation, yttrium and strontium are eluted from the column with water or methanol. In the procedure of direct isolation from 1 l of the sample, the average recovery of 50% was obtained. In the remaining two procedures, the strontium recovery was about 60% for the Sr column and 65% for anion exchange column. Recovery of yttrium is about 70% for the anion exchange column. It turned out that the procedure with the Sr resin (direct isolation and isolation after precipitation) is simpler and faster in the phase of the isolation on the column in comparison with the procedure with the anion exchanger. The procedure with the anion exchanger, however, enables the simultaneous isolation of yttrium and strontium and rapid determination of 89,90 Sr. These procedures were tested by determination of 89,90 Sr on liquid scintillation counter and Cherenkov

Evidence of organic luminescent centers in sol-gel-synthesized yttrium aluminum borate matrix leading to bright visible emission

Energy Technology Data Exchange (ETDEWEB)

Burner, Pauline; Salauen, Mathieu; Ibanez, Alain; Gautier-Luneau, Isabelle [Univ. Grenoble Alpes, Inst NEEL, Grenoble (France); CNRS, Inst NEEL, Grenoble (France); Sontakke, Atul D.; Viana, Bruno [PSL Research University, Chimie ParisTech - CNRS, Institut de Recherche de Chimie Paris (France); Bardet, Michel [Universite Grenoble Alpes, CEA, CNRS, INAC, MEM, Grenoble (France); Mouesca, Jean-Marie; Gambarelli, Serge; Maurel, Vincent [Universite Grenoble Alpes, CEA, CNRS, INAC, SyMMES, Grenoble (France); Barra, Anne-Laure [Laboratoire National des Champs Magnetiques Intenses, UPR CNRS 3228, Universite Grenoble Alpes, Grenoble (France); Ferrier, Alban [PSL Research University, Chimie ParisTech - CNRS, Institut de Recherche de Chimie Paris (France); Sorbonne Universites UPMC Universites Paris 06, Paris (France)

2017-11-06

Yttrium aluminum borate (YAB) powders prepared by sol-gel process have been investigated to understand their photoluminescence (PL) mechanism. The amorphous YAB powders exhibit bright visible PL from blue emission for powders calcined at 450 C to broad white PL for higher calcination temperature. Thanks to {sup 13}C labelling, NMR and EPR studies show that propionic acid initially used to solubilize the yttrium nitrate is decomposed into aromatic molecules confined within the inorganic matrix. DTA-TG-MS analyses show around 2 wt % of carbogenic species. The PL broadening corresponds to the apparition of a new band at 550 nm, associated with the formation of aromatic species. Furthermore, pulsed ENDOR spectroscopy combined with DFT calculations enables us to ascribe EPR spectra to free radicals derived from small (2 to 3 rings) polycyclic aromatic hydrocarbons (PAH). PAH molecules are thus at the origin of the PL as corroborated by slow afterglow decay and thermoluminescence experiments. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

25 CFR 89.31 - Negotiation of contract.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Negotiation of contract. 89.31 Section 89.31 Indians BUREAU OF INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR TRIBAL GOVERNMENT ATTORNEY CONTRACTS WITH INDIAN TRIBES Five Civilized Tribes § 89.31 Negotiation of contract. That person or governing entity recognized as having authority to act for and in behalf o...

40 CFR 89.410 - Engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine test cycle. 89.410 Section 89... Procedures § 89.410 Engine test cycle. (a) Emissions shall be measured using one of the test cycles specified...) through (a)(4) of this section. These cycles shall be used to test engines on a dynamometer. (1) The 8...

Recommendations for radioembolisation after liver surgery using yttrium-90 resin microspheres based on a survey of an international expert panel

International Nuclear Information System (INIS)

Samim, Morsal; Veenendaal, Linde M. van; Braat, Manon N.G.J.A.; Hoven, Andor F. van den; Bosch, Maurice A.A.J. van den; Lam, Marnix G.E.H.; Hillegersberg, Richard van; Sangro, Bruno; Kao, Yung Hsiang; Liu, Dave; Louie, John D.; Sze, Daniel Y.; Rose, Steven C.; Brown, Daniel B.; Ahmadzadehfar, Hojjat; Kim, Edward

2017-01-01

Guidelines on how to adjust activity in patients with a history of liver surgery who are undergoing yttrium-90 radioembolisation ( 90 Y-RE) are lacking. The aim was to study the variability in activity prescription in these patients, between centres with extensive experience using resin microspheres 90 Y-RE, and to draw recommendations on activity prescription based on an expert consensus. The variability in activity prescription between centres was investigated by a survey of international experts in the field of 90 Y-RE. Six representative post-surgical patients (i.e. comparable activity prescription, different outcome) were selected. Information on patients' disease characteristics and data needed for activity calculation was presented to the expert panel. Reported was the used method for activity prescription and whether, how and why activity reduction was found indicated. Ten experts took part in the survey. Recommendations on activity reduction were highly variable between the expert panel. The median intra-patient range was 44 Gy (range 18-55 Gy). Reductions in prescribed activity were recommended in 68% of the cases. In consensus, a maximum D Target of 50 Gy was recommended. With a current lack of guidelines, large variability in activity prescription in post-surgical patients undergoing 90 Y-RE exists. In consensus, D Target ≤50 Gy is recommended. (orig.)

MCrAlY bond coat with enhanced yttrium

Science.gov (United States)

Jablonski, Paul D.; Hawk, Jeffrey A.

2016-08-30

One or more embodiments relates to a method of producing an MCrAlY bond coat comprising an MCrAlY layer in contact with a Y--Al.sub.2O.sub.3 layer. The MCrAlY layer is comprised of a .gamma.-M solid solution, a .beta.-MAl intermetallic phase, and Y-type intermetallics. The Y--Al.sub.2O.sub.3 layer is comprised of Yttrium atoms coordinated with oxygen atoms comprising the Al.sub.2O.sub.3 lattice. The method comprises depositing an MCrAlY material on a substrate, applying an Y.sub.2O.sub.3 paste, and heating the substrate in a non-oxidizing atmosphere at a temperature between 400-1300.degree. C. for a time sufficient to generate the Y--Al.sub.2O.sub.3 layer. Both the MCrAlY layer and the Y--Al.sub.2O.sub.3 layer have a substantial absence of Y.sub.2O.sub.3, YAG, and YAP phases.

The spectrum of singly ionized yttrium, Y II

International Nuclear Information System (INIS)

Nilsson, A.E.; Johansson, S.; Kurucz, R.L.

1991-01-01

Hollow-cathode spectra of yttrium have been registered in the wavelength region 1000-48800 A. Resonant charge transfer reactions in the light source favour the excitation of Y II, where 174 new levels have been established by means of 1284 newly classified lines. Altogether we report 1521 lines between 235 levels in Y II. The ground complex (4d+5s) 2 is now completely known and a number of Rydberg series have been extended. The new levels belong to the 4dnl (nl=7s, 8s, 9s, 6p, 7p, 4d, 5d, 6d, 7d, 8d, 4f, 5f, 6f, 7f, 5g) and 5snl (nl=7s, 8s, 6p, 6d, 4f, 5f) configurations. Eigenvector compositions, based on paramagnetic calculations including configuration interaction, are given for all levels. The ionization limit has been determined to 98590 ± 5 cm -1 . (orig.)

Unix version of CALOR89 for calorimeter applications

International Nuclear Information System (INIS)

Handler, T.

1992-01-01

CALOR89 is a system of coupled Monte Carlo particle transport computer codes which has been successfully employed for the estimation of calorimeter parameters in High Energy Physics. In the past CALOR89 has been running on various IBM machines and on CRAY X-MP at Lawrence Livermore Lab. These machines had non-unix operating systems. In this report we present a UNIX version of CALOR89, which is especially suited for the UNIX work stations. Moreover CALOR89 is also been supplemented with two new program packages which makes it more user friendly. CALPREP is a program for the preparation of the input files for CALOR89 in general geometry and ANALYZ is an analysis package to extract the final results from CALOR89 relevant to calorimeters. This report also provides two script files LCALOR and PCALOR. LCALOR runs CALOR89 sequences of programs and EGS4 for a given configuration sequentially on a single processor and PCALOR concurrently on a multiprocessor unix workstation

Successful treatment of Cushing's disease using yttrium-90 rods

International Nuclear Information System (INIS)

White, M.C.; Doyle, F.H.; Mashiter, K.; Joplin, G.F.

1982-01-01

Interstitial irradiation using yttrium-90 ( 90 Y) rods implanted by needle into the pituitary gland was used as primary treatment in 16 patients with pituitary dependent Cushing's disease. Clinical and biochemical remission was observed within three to six months in 13 and in the remaining three after a supplementary implant. There was no perioperative morbidity. Follow-up from the time of definitive operation ranged from six to 123 months (mean 39). No recurrence has been observed. The return of a normal diurnal cortisol rhythm has been observed in 10/12 patients studied after remission. Some form of long-term pituitary hormone replacement therapy was required in only the six patients who had received the largest irradiation dose. Implantation of 90 Y is safe and effective treatment for patients with Cushing's disease, comparing favourably with selective trans-sphenoidal pituitary surgery. (author)

Quantitation in PET using isotopes emitting prompt single gammas: application to yttrium-86

International Nuclear Information System (INIS)

Walrand, Stephan; Jamar, Francois; Mathieu, Isabelle; De Camps, Joelle; Lonneux, Max; Pauwels, Stanislas; Sibomana, Merence; Labar, Daniel; Michel, Christian

2003-01-01

Several yttrium-90 labelled somatostatin analogues are now available for cancer radiotherapy. After injection, a large amount of the compound is excreted via the urinary tract, while a variable part is trapped in the tumour(s), allowing the curative effect. Unfortunately, the compound may also be trapped in critical tissues such as kidney or bone marrow. As a consequence, a method for assessment of individual biodistribution and pharmacokinetics is required to predict the maximum dose that can be safely injected into patients. However, 90 Y, a pure β - particle emitter, cannot be used for quantitative imaging. Yttrium-86 is a positron emitter that allows imaging of tissue uptake using a PET camera. In addition to the positron, 86 Y also emits a multitude of prompt single γ-rays, leading to significant overestimation of uptake when using classical reconstruction methods. We propose a patient-dependent correction method based on sinogram tail fitting using an 86 Y point spread function library. When applied to abdominal phantom acquisition data, the proposed correction method significantly improved the accuracy of the quantification: the initial overestimation of background activity by 117% was reduced to 9%, while the initial error in respect of kidney uptake by 84% was reduced to 5%. In patient studies, the mean discrepancy between PET total body activity and the activity expected from urinary collections was reduced from 92% to 7%, showing the benefit of the proposed correction method. (orig.)

9 CFR 89.5 - Feeding pens.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Feeding pens. 89.5 Section 89.5 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS STATEMENT OF POLICY UNDER THE...

The influence of predeformations and annealings on yield stress and modulus of elongation essentially yttrium doped copper

International Nuclear Information System (INIS)

Neklyudov, I.M.; Sytin, V.I.; Voevodin, V.N.

2003-01-01

The researches results of influence of predeformations and annealings on elastic and plastic characteristics of vacuum melting and yttrium doped copper are given. The interrelation between elastic and plastic characteristics has been shown. It is shown that the yield stress and modulus of elongation essentially depend on predeformations and annealings and they are the structurally sensitive characteristics

Imaging the L-type amino acid transporter-1 (LAT1 with Zr-89 immunoPET.

Directory of Open Access Journals (Sweden)

Oluwatayo F Ikotun

Full Text Available The L-type amino acid transporter-1 (LAT1, SLC7A5 is upregulated in a wide range of human cancers, positively correlated with the biological aggressiveness of tumors, and a promising target for both imaging and therapy. Radiolabeled amino acids such as O-(2-[(18F]fluoroethyl-L-tyrosine (FET that are transport substrates for system L amino acid transporters including LAT1 have met limited success for oncologic imaging outside of the brain, and thus new strategies are needed for imaging LAT1 in systemic cancers. Here, we describe the development and biological evaluation of a novel zirconium-89 labeled antibody, [(89Zr]DFO-Ab2, targeting the extracellular domain of LAT1 in a preclinical model of colorectal cancer. This tracer demonstrated specificity for LAT1 in vitro and in vivo with excellent tumor imaging properties in mice with xenograft tumors. PET imaging studies showed high tumor uptake, with optimal tumor-to-non target contrast achieved at 7 days post administration. Biodistribution studies demonstrated tumor uptake of 10.5 ± 1.8 percent injected dose per gram (%ID/g at 7 days with a tumor to muscle ratio of 13 to 1. In contrast, the peak tumor uptake of the radiolabeled amino acid [(18F]FET was 4.4 ± 0.5 %ID/g at 30 min after injection with a tumor to muscle ratio of 1.4 to 1. Blocking studies with unlabeled anti-LAT1 antibody demonstrated a 55% reduction of [(89Zr]DFO-Ab2 accumulation in the tumor at 7 days. These results are the first report of direct PET imaging of LAT1 and demonstrate the potential of immunoPET agents for imaging specific amino acid transporters.

Substitution of yttrium for boron in the structure of YBa2Cu3O7-δ

International Nuclear Information System (INIS)

Dwelk, H.; Herrmann, R.; Pruss, N.; Freude, D.; Pfeifer, H.

1989-01-01

The influence of boron on superconducting properties of Y 1-x B x Ba 2 Cu 3 O 7-δ with x = 0 to 0.4 is studied. The analysis of 11 B NMR spectra and measurements of electric conductivity as a function of temperature show that boron is not incorporated into the YBa 2 Cu 3 O 7-δ framework on yttrium positions. (author)

Electrical properties of single crystal Yttrium Iron Garnet ultra-thin films at high temperatures

OpenAIRE

Thiery, Nicolas; Naletov, Vladimir V.; Vila, Laurent; Marty, Alain; Brenac, Ariel; Jacquot, Jean-François; de Loubens, Grégoire; Viret, Michel; Anane, Abdelmadjid; Cros, Vincent; Youssef, Jamal Ben; Demidov, Vladislav E.; Demokritov, Sergej O.; Klein, Olivier

2017-01-01

We report a study on the electrical properties of 19 nm thick Yttrium Iron Garnet (YIG) films grown by liquid phase epitaxy. The electrical conductivity and Hall coefficient are measured in the high temperature range [300,400]~K using a Van der Pauw four-point probe technique. We find that the electrical resistivity decreases exponentially with increasing temperature following an activated behavior corresponding to a band-gap of $E_g\\approx 2$ eV, indicating that epitaxial YIG ultra-thin film...

40 CFR 745.89 - Firm certification.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Firm certification. 745.89 Section 745... § 745.89 Firm certification. (a) Initial certification. (1) Firms that perform renovations for compensation must apply to EPA for certification to perform renovations or dust sampling. To apply, a firm must...

40 CFR 141.89 - Analytical methods.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 22 2010-07-01 2010-07-01 false Analytical methods. 141.89 Section 141...) NATIONAL PRIMARY DRINKING WATER REGULATIONS Control of Lead and Copper § 141.89 Analytical methods. (a... shall be conducted with the methods in § 141.23(k)(1). (1) Analyses for alkalinity, calcium...

Kinetics and mechanism of the low-temperature yttrium-aluminium garnet synthesis

International Nuclear Information System (INIS)

Ivakin, Yu.D.; Danchevskaya, M.N.; Yanchenko, P.A.; Murav'eva, G.P.

2000-01-01

Kinetics and formation mechanism of finely crystalline yttrium-aluminium garnet (YAG) during hydrothermal and hot steam treatment of stoichiometric mixture of oxides in the range of temperature 200-400 Deg C and pressures of 1.5-26 MPa were studied. It is ascertained that formation of YAG occurs via intermediate stage of Y(OH) 3 structure formation, whereas the aluminia component is X-ray amorphous. Kinetics of YAG formation is described by the equation of solid phase transformation with the limiting stage of nucleation. The YAG formed contains 7-5 % of water, which corresponds to hydrogarnet structure. Unit cell parameters of the YAG samples synthesized are somewhat high and after heating up to 1200 Deg C they decrease [ru

Effect of phase composition on the corrosion properties of alloys of the magnesium-yttrium system in neutral solutions

International Nuclear Information System (INIS)

Krasnoyarskii, V.V.; Petrova, L.M.; Dobatkina, T.V.; Korol'kova, I.G.

1992-01-01

A study is made of the effect of phase composition on the corrosive dissolution of binary alloys of the system magnesium-8.2% yttrium. It is shown that the appearance of the intermetallide Mg 24 Y 5 - being the effective cathode - intensifies self-dissolution of the alloy under conditions of anodic galvanostatic polarization

Optimized conditions for chelation of yttrium-90-DOTA immunoconjugates.

Science.gov (United States)

Kukis, D L; DeNardo, S J; DeNardo, G L; O'Donnell, R T; Meares, C F

1998-12-01

Radioimmunotherapy (RIT) with 90Y-labeled immunoconjugates has shown promise in clinical trials. The macrocyclic chelating agent 1,4,7,10-tetraazacyclododecane-N,N',N",N"'-tetraacetic acid (DOTA) binds 90Y with extraordinary stability, minimizing the toxicity of 90Y-DOTA immunoconjugates arising from loss of 90Y to bone. However, reported 90Y-DOTA immunoconjugate product yields have been typically only BAD) was conjugated to the monoclonal antibody Lym-1 via 2-iminothiolane (2IT). The immunoconjugate product, 2IT-BAD-Lym-1, was labeled in excess yttrium in various buffers over a range of concentrations and pH. Kinetic studies were performed in selected buffers to estimate radiolabeling reaction times under prospective radiopharmacy labeling conditions. The effect of temperature on reaction kinetics was examined. Optimal radiolabeling conditions were identified and used in eight radiolabeling experiments with 2IT-BAD-Lym-1 and a second immunoconjugate, DOTA-peptide-chimeric L6, with 248-492 MBq (6.7-13.3 mCi) of 90Y. Ammonium acetate buffer (0.5 M) was associated with the highest uptake of yttrium. On the basis of kinetic data, the time required to chelate 94% of 90Y (four half-times) under prospective radiopharmacy labeling conditions in 0.5 M ammonium acetate was 17-148 min at pH 6.5, but it was only 1-10 min at pH 7.5. Raising the reaction temperature from 25 degrees C to 37 degrees C markedly increased the chelation rate. Optimal radiolabeling conditions were identified as: 30-min reaction time, 0.5 M ammonium acetate buffer, pH 7-7.5 and 37 degrees C. In eight labeling experiments under optimal conditions, a mean product yield (+/- s.d.) of 91%+/-8% was achieved, comparable to iodination yields. The specific activity of final products was 74-130 MBq (2.0-3.5 mCi) of 90Y per mg of monoclonal antibody. The immunoreactivity of 90Y-labeled immunoconjugates was 100%+/-11%. The optimization of 90Y-DOTA chelation conditions represents an important advance in 90Y RIT

Yttrium-enriched YBa{sub 2}Cu{sub 3}O{sub x} thin films for coated conductors fabricated by pulsed laser deposition

Energy Technology Data Exchange (ETDEWEB)

Khoryushin, Alexey V., E-mail: khoryushin@ya.ru [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark); Mozhaev, Peter B.; Mozhaeva, Julia E.; Andersen, Niels H. [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark); Grivel, Jean-Claude [Department of Energy Conversion and Storage, Technical University of Denmark, DK-4000 Roskilde (Denmark); Hansen, Jørn Bindslev; Jacobsen, Claus S. [Department of Physics, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark)

2013-02-14

Highlights: ► YBCO films were fabricated by PLD from targets of various elemental compositions. ► The Y-enriched films contain yttria nanoparticles which provide efficient pinning. ► The best film has 5.5× higher j{sub c}(5 T,50 K) = 2.6MA/cm{sup 2} comparing with a reference film. ► The Y-enriched films remain c-oriented up to 500 nm. ► Films demonstrate no j{sub c} suppression with thickness and remarkable stability with time. -- Abstract: The effects of excess yttria on the structural and electrical properties of the YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) thin films are studied. The films were deposited on (LaAlO{sub 3}){sub 0.3}–(Sr{sub 2}AlTaO{sub 8}){sub 0.7} substrates by pulsed laser ablation from targets with different elemental composition. An increase of yttrium content of the target leads to formation of porous films with significantly improved current-carrying capabilities. Structural studies of these films reveal presence of yttria nanoparticles embedded into the YBCO matrix. The highest obtained critical current density in an external magnetic field of 5 T was 2.6 MA/cm{sup 2} at 50 K and 9.4 MA/cm{sup 2} at 20 K. The fabricated Y-enriched YBCO films remain c-oriented at least up to 600 nm thickness with no significant suppression of the critical current density.

radio embolization of yttrium 90 glass microspheres in treatment of hepatocellular carcinoma

International Nuclear Information System (INIS)

El Fouly, A.H.A.

2010-01-01

Hepatocellular carcinoma (HCC) is a common cancer that typically occurs in the setting of cirrhosis and chronic hepatitis virus infections. HCC is considered currently as global problem; its incidence is expected to increase dramatically by the next few decades. More than 90 % of the accidentally diagnosed patients have non resectable tumor. Portal vein thrombosis, diffuse multifocal liver infiltration and large tumor burden are considered to be a great obstacle in front of the modern lines of treatment, even with Child A liver cirrhosis. Transarterial intrahepatic application of Yttrium-90 glass microspheres may allow effective local ablative treatment of patients with intrahepatic advanced hepatocellular carcinoma (HCC) with or without portal vein thrombosis. The aim of this open-label phase II study was to validate evidence on the safety and efficacy of this treatment in an European cohort of patients with locally advanced HCC such as (large tumor burden, multifocal distribution, portal vein thrombosis). And to assess the response rate according to different approved response assessment guidelines (WHO, RECIST and EASL). Patients and Methods Starting from November 2006 till March 2009, one hundred and eight advanced unresectable HCC patients with and without portal vein thrombosis were included in this prospective study. Yttrium-90 microspheres radiotherapy was performed in a lobar fashion through the right or left hepatic artery. In bilobar disease, right and left liver lobe were treated with 4-6 weeks intervals in between. Response rate was assessed according to different international response assessment criteria (WHO, RECIST and EASL) with sequential computed tomography scans till the last clinical visit or death. The safety of this technique was assessed according to the Common Toxicity Criteria version 3

Biodistribution of Yttrium-90-Labeled Anti-CD45 Antibody in a Nonhuman Primate Model

International Nuclear Information System (INIS)

Nemecek, Eneida; Hamlin, Donald K.; Fisher, Darrell R.; Krohn, Kenneth A.; Pagel, John M.; Applebaum, F. R.; Press, Oliver W.; Matthews, Dana C.

2005-01-01

Radioimmunotherapy may improve the outcome of hematopoietic cell transplantation for hematologic malignancies by delivering targeted radiation to hematopoietic organs while relatively sparing nontarget organs. We evaluated the organ localization of yttrium-90-labeled anti-CD45 (90Y-anti-CD45) antibody in macaques, a model that had previously predicted iodine-131-labeled anti-CD-45 (131I-anti-CD45) antibody biodistribution in humans. Experimental Design: Twelve Macaca nemestrina primates received anti-CD45 antibody labeled with 1 to 2 mCi of 90Y followed by serial blood sampling and marrow and lymph node biopsies, and necropsy. The content of 90Y per gram of tissue was determined by liquid scintillation spectrometry. Time-activity curves were constructed using average isotope concentrations in each tissue at measured time points to yield the fractional residence time and estimate radiation absorbed doses for each organ per unit of administered activity. The biodistribution of 90Y-anti-CD45 antibody was then compared with that previously obtained with 131I-anti-CD45 antibody in macaques. Results: The spleen received 2,120, marrow 1,060, and lymph nodes 315 cGy/mCi of 90Y injected. The liver and lungs were the nontarget organs receiving the highest radiation absorbed doses (440 and 285 cGy/mCi, respectively). Ytrrium-90-labeled anti-CD45 antibody delivered 2.5- and 3.7-fold more radiation to marrow than to liver and lungs, respectively. The ratios previously observed with 131I-antiCD45 antibody were 2.5-and 2.2-fold more radiation to marrow than to liver and lungs, respectively. Conclusions: This study shows that 90Y-anti-CD45 antibody can deliver relatively selective radiation to hematopoietic tissues, with similar ratios of radiation delivered to target versus nontarget organs, as compared with the 131I immunoconjugate in the same animal model

Compounds of addition between yttrium and rare-earths (III) nitrates and the N,N,N'N'-tetramethyladipamide (TMAA)

International Nuclear Information System (INIS)

Lima, W.N. de.

1974-01-01

The synthesis of addition compounds between hydrated rare-earths and yttrium nitrates with the diamine N,N,N',N'-tetramethyladipamide (TMAA) in ethanol, is described. The compounds were characterized by elemental analisys, infrared, Raman, visible and near infrared spectra, molar conductance and molecular weight measurements, conductometric titrations and X-ray powder patterns. (Author) [pt

Neutron total, scattering and inelastic gamma-ray cross sections of yttrium at few MeV energies

International Nuclear Information System (INIS)

Budtz-Joergensen, C.; Guenther, P.; Smith, A.; Whalen, J.; McMurray, W.R.; Renan, M.J.; Heerden, I.J. van

1984-01-01

Neutron total, scattering and (n; n', γ) cross sections of elemental yttrium ( 89 Y) were measured in the few-MeV region. The neutron total-cross-section measurements were made with broad resolutions from approx.=0.5 to 4.2 MeV in steps of < or approx.0.1 MeV. Neutron elastic- and inelastic-scattering cross sections were measured from approx.=1.5 to 4.0 MeV, at incident-neutron energy intervals of approx.=50 keV and at ten or more scattering angles distributed between 20 and 160 degrees using neutron detection. Inelastic-scattering cross sections were also determined using the (n; n', γ) reaction at incident energies from 1.6 to 3.8 MeV at intervals of 0.1 MeV. Gamma-rays and/or inelastically-scattered neutrons were observed corresponding to the excitation of levels at: 909.0+-0.5, 1,507.4+-0.3, 1,744.5+-0.3, 2,222.6+-0.5, 2,530+-0.8, 2,566.4+-1.0, 2,622.5+-1.0, 2,871.9+-1.5, 2,880.6+-2.0, 3,067.0+-2.0, 3,107.0+-2.0, 3,140.0+-2.0, 3,410.0+-2.0, 3,450.0+-2.0, 3,504.0+-1.5, 3,514.0+-2.0, 3,556.0+-2.0, 3,619.0+-3.0, 3,629.0+-3.0 and 3,715.0+-3.0 keV. The experimental results are discussed in terms of the spherical-optical-statistical, coupled-channels, and core-coupling models, and in the context of previously reported excited-level structure. (orig.)

33 CFR 401.89 - Transit refused.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Transit refused. 401.89 Section... TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations General § 401.89 Transit refused. (a) An officer may refuse to allow a vessel to transit when, (1) The vessel is not equipped in accordance with §§ 401.5 to...

Ultra-low damping in lift-off structured yttrium iron garnet thin films

Science.gov (United States)

Krysztofik, A.; Coy, L. E.; Kuświk, P.; Załeski, K.; Głowiński, H.; Dubowik, J.

2017-11-01

We show that using maskless photolithography and the lift-off technique, patterned yttrium iron garnet thin films possessing ultra-low Gilbert damping can be accomplished. The films of 70 nm thickness were grown on (001)-oriented gadolinium gallium garnet by means of pulsed laser deposition, and they exhibit high crystalline quality, low surface roughness, and the effective magnetization of 127 emu/cm3. The Gilbert damping parameter is as low as 5 ×10-4. The obtained structures have well-defined sharp edges which along with good structural and magnetic film properties pave a path in the fabrication of high-quality magnonic circuits and oxide-based spintronic devices.

Metastable phases in yttrium oxide plasma spray deposits and their effect on coating properties

International Nuclear Information System (INIS)

Gourlaouen, V.; Schnedecker, G.; Boncoeur, M.; Lejus, A.M.; Collongues, R.

1993-01-01

Yttrium oxide coatings were obtained by plasma spray. Structural investigations on these deposits show that, due to the drastic conditions of this technique, a minor monoclinic B phase is formed in the neighborhood of the major cubic C form. The authors discuss here the influence of different plasma spray parameters on the amount of the B phase formed. They describe also the main properties of Y 2 O 3 B and C phases in these deposits such as structural characteristics, thermal stability and mechanical behavior

The influence of cerium and yttrium ion implantation upon the oxidation behaviour of a 20% Cr/25% Ni/Nb stabilised stainless steel, in carbon dioxide, at 8250C

International Nuclear Information System (INIS)

Bennett, M.J.; Dearnaley, G.; Houlton, M.R.; Hawes, R.W.M.

1982-01-01

The influence of cerium and yttrium ion implantation upon the oxidation behaviour of a 20% Cr/25% Ni niobium stabilised stainless steel during up to 7 157h exposure to carbon dioxide, at 825 0 C has been examined. The doses ranged between 5 x 10 14 and 10 17 ions cm -2 . Above thresholds of between 5 x 10 14 and 5 x 10 15 yttrium and between 5 x 10 15 and 10 16 cerium ions cm -2 the implantation of both elements improved the oxidation resistance of the 20/25/Nb steel. Yttrium exerted the greater influence, reducing by a factor of two the attack after 7 157h. Up to 80% of the oxide formed on the 20/25/Nb steel spalled, particularly on thermal cycling. Cerium and yttrium implantation improved oxide adhesion by similar extents, which increased with ion dose such that with the highest doses, no spallation was measurable. The effect of the implanted elements derived from their incorporation within the oxide film. It was initiated by their promotion of the formation of an initial chromium-rich oxide layer, which had a finer grain size than that formed on the 20/25/Nb steel. Reduction in continuing attack was associated in part, with improved oxide adhesion, as this decreased the significant contribution to the attack of the 20/25/Nb steel from the reoxidation of spalled areas. (author)

The relevance of rare earth elements to nuclear medicine

International Nuclear Information System (INIS)

Cox, P.H.

1998-01-01

Full text: The lanthanides are an interesting series of metallic elements which have almost identical chemical characteristics and which offer a variety of radioisotopes with differing energy spectra suitable for open source therapy. Their inorganic salts tend to form chemically and biological stable colloids which have proved to be useful for intercavity therapies, in particular for synovectomy. Yttrium-90 silicate is a standard product for large joints with a thick synovium whilst for smaller joints Erbium-169, with its shorter tissue penetration, is more widely used for smaller joints to reduce the risk of radiation induced bone necrosis. Recently the development of an inert biodegradable colloid, chitosan, labelled with Holmium 166. for intercavity therapy of cystic brain tumours has been reported. Yttrium-90 has been chelated to peptide and antibody fragments for tumour targeting as a potentially more effective radionuclide than Iodine-131. The search for alternatives to Strontium-89 for the palliative treatment of pain arising from bone metastases has led to the introduction of diphosphonate complexes of Samarium-153, Lutetium-177 and Holmium-166. These complexes are of special interest because the radionuclides can be produced economically in developing countries. Terbium-149, an alpha emitter, has been mentioned as a possible therapeutic radionuclide. Yttrium-90 and Holmium-166 can an both be made available as generator products which is an added potential advantage for developing nuclear medical applications

Studies on yttrium-containing smart alloys

Energy Technology Data Exchange (ETDEWEB)

Klein, Felix; Wegener, Tobias; Litnovsky, Andrey; Rasinski, Marcin; Linsmeier, Christian [Forschungszentrum Juelich GmbH, Institut fuer Energie- und Klimaforschung - Plasmaphysik (Germany); Mayer, Joachim [Ernst Ruska-Centrum, 52425 Juelich (Germany)

2016-07-01

Tungsten is the main candidate as plasma-facing armour material for future fusion reactors, like DEMO. Advantages of tungsten include high melting point, high thermal conductivity, low tritium retention, and low erosion yield. A problem is oxide volatilisation under accidental conditions where the temperature of the first wall can reach 1200 K to 1450 K and air ingress occurs. Therefore smart tungsten alloys are developed. Smart alloys are supposed to preserve properties of tungsten during plasma operation coupled with suppressed tungsten oxide formation in case of an accident. Lab-scale tungsten-chromium-yttrium (W-Cr-Y) samples prepared by magnetron sputtering are used as model system. The mechanisms of oxidation and its dynamics are studied using a thermogravimetric system, focussed ion beam, and electron microscopy. A composition scan was conducted: The new material composition featuring W, ∝ 12 wt.% Cr, ∝ 0.3 wt.% Y showed strongest suppression of oxidation, no pores, and least internal oxidation. At 1273 K in argon-oxygen atmosphere an oxidation rate of 3 . 10{sup -6} mg{sup 2}cm{sup -4}s{sup -1} was measured. At 1473 K ternary W-Cr-Y alloys suppressed evaporation up to 20 min while for W-Cr evaporation was already evident after 5 min. Comparison of passivation in dry and humid atmosphere, at temperatures of 1073 K to 1473 K is performed.

4 CFR 28.89 - Attorney's fees and costs.

Science.gov (United States)

2010-01-01

... 4 Accounts 1 2010-01-01 2010-01-01 false Attorney's fees and costs. 28.89 Section 28.89 Accounts... Procedures Board Decisions, Attorney's Fees and Judicial Review § 28.89 Attorney's fees and costs. Within 20... party, may submit a request for the award of reasonable attorney's fees and costs. GAO may file a...

A Woman with Black Beads in Her Stomach: Severe Gastric Ulceration Caused by Yttrium-90 Radioembolization

Directory of Open Access Journals (Sweden)

Indu S. Voruganti

2018-01-01

Full Text Available Radioembolization (RE is a selective internal radiation therapy (SIRT delivering targeted, high-dose, intra-arterial radiation directly to the vascular supply of liver tumors. Complications can occur due to aberrant deposition or migration of radiation microspheres into nontarget locations, including normal hepatic parenchyma, lungs, pancreas, and upper gastrointestinal (UGI tract. We report a case of gastric ulcers due to yttrium-90 (90Y seed migration to the stomach to alert clinicians to this rare cause of gastric injury. A 57-year-old woman with stage IV breast cancer with liver and lung metastases presented to the hospital with 2 months of worsening nausea and vomiting. Two months prior, she had received SIRT with 90Y microspheres without complications. Upper GI endoscopy showed diffuse gastritis and extensive antral ulceration. Biopsies revealed black, spherical foreign bodies, consistent with 90Y microspheres, documenting radiation injury. Radiation-induced UGI ulceration is caused by direct radiation injury from beta-radiation. Delay in diagnosis may be due to the nonspecificity of symptoms and temporal delay of symptom onset from SIRT, which was 2 months in our patient. Also, complaints may be attributed erroneously to adjuvant chemotherapy or widespread metastatic disease. Clinicians must consider radiation-associated toxicity in any SIRT-treated patient developing abdominal symptoms.

Optical properties of ytterbium-doped yttrium oxide ceramics

Energy Technology Data Exchange (ETDEWEB)

Solomonov, V.I.; Maksimov, R.N. [Institute of Electrophysics UrB RAS, Amundsena 106, 620016 Ekaterinburg (Russian Federation); Ural Federal University Named After the First President of Russia B.N. Yeltsin, Mira 19, 620002 Ekaterinburg (Russian Federation); Osipov, V.V.; Shitov, V.A.; Lipchak, A.I. [Institute of Electrophysics UrB RAS, Amundsena 106, 620016 Ekaterinburg (Russian Federation)

2017-05-15

Ytterbium-doped yttrium oxide (Yb:Y{sub 2}O{sub 3}) transparent ceramics with different sintering additives (Lu{sub 2}O{sub 3}, Sc{sub 2}O{sub 3}, CeO{sub 2}, ZrO{sub 2}, or HfO{sub 2}) were fabricated using nanopowders produced by laser ablation. Transmission and photoluminescence spectra of the obtained ceramics were investigated at room temperature. Highest in-line transmittance was over 80% at the wavelength of 1060 nm for 2 mm thick Yb:Y{sub 2}O{sub 3} ceramics with zirconium and hafnium. Divalent Yb ions with the ground state electron configuration 4f{sup 13}6s were revealed. The absorption and emission bands caused by s <-> s transitions of these ions were observed in the IR spectral range of Yb{sup 3+} ions. The superposition of both Yb{sup 3+} and Yb{sup 2+} emission bands leads to an effective broadening of the whole luminescence band. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Fabrication of cerium-doped yttrium aluminum garnet thin films by a mist CVD method

Energy Technology Data Exchange (ETDEWEB)

Murai, Shunsuke, E-mail: murai@dipole7.kuic.kyoto-u.ac.jp; Sato, Takafumi; Yao, Situ; Kamakura, Ryosuke; Fujita, Koji; Tanaka, Katsuhisa

2016-02-15

We synthesized thin films, consisting of yttrium aluminum garnet doped with Ce{sup 3+} (YAG:Ce), using the mist chemical vapor deposition (CVD) method, which allows the fabrication of high-quality thin films under atmospheric conditions without the use of vacuum equipment. Under a deposition rate of approximately 1 μm/h, the obtained thin films had a typical thickness of 2 μm. The XRD analysis indicated that the thin films consisted of single-phase YAG:Ce. The Rutherford backscattering confirmed the stoichiometry; the composition of the film was determined to be (Y, Ce){sub 3}Al{sub 5}O{sub 12}, with a Ce content of Ce/(Y+Ce)=2.5%. The YAG:Ce thin films exhibited fluorescence due to the 5d–4f electronic transitions characteristic of the Ce ions occupying the eight-coordinated dodecahedral sites in the YAG lattice. - Highlights: • We have synthesized thin films of yttrium aluminum garnet doped with Ce{sup 3+} (YAG:Ce) by using a mist chemical vapor deposition (CVD) method for the first time. • The thickness of the single-phase and stoichiometric thin film obtained by 2 h deposition and following heat treatments is 2 μm. • The thin film is porous but optically transparent, and shows yellow fluorescence upon irradiation with a blue light. • Mist-CVD is a green and sustainable technique that allows fabrication of high-quality thin films at atmospheric conditions without vacuum equipment.

Microstructural evolution of 316L stainless steels with yttrium addition after mechanical milling and heat treatment

Energy Technology Data Exchange (ETDEWEB)

Kotan, Hasan, E-mail: hasankotan@gmail.com

2015-10-28

Nanocrystalline 316L stainless steels with yttrium addition were prepared by mechanical milling at cryogenic temperature and subjected to annealing treatments at various temperatures up to 1200 °C. The dependence of hardness on the microstructure was utilized to study the mechanical changes in the steels occurring during annealing. The microstructural evolution of the as-milled and annealed steels was characterized by means of X-ray diffraction (XRD), focused ion beam microscopy (FIB) and transmission electron microscopy (TEM) techniques. The results have revealed that austenite in as-received powder partially transformed to martensite phase during mechanical milling whereas the annealing induced reverse transformation of martensite-to-austenite. Furthermore, while the austenite-to-martensite phase ratio increased with increasing annealing temperature, the equilibrium structure was not achieved after three hours heat treatments up to 1200 °C resulting in a dual-phased steels with around 10% martensite. The grain size of 316L steel was 19 nm after mechanical milling and remained around 116 nm at 1100 °C with yttrium addition as opposed to micron size grains of plain 316L steel at the same annealing temperature. Such microstructural features facilitate the use of these materials at elevated temperatures, as well as the development of scalable processing routes into a dense nanocrystalline compact.

Recommendations for radioembolisation after liver surgery using yttrium-90 resin microspheres based on a survey of an international expert panel

Energy Technology Data Exchange (ETDEWEB)

Samim, Morsal [University Medical Center Utrecht, Department of Surgery, Utrecht (Netherlands); University Medical Center Utrecht, Department of Radiology and Nuclear Medicine, Utrecht (Netherlands); Veenendaal, Linde M. van; Braat, Manon N.G.J.A.; Hoven, Andor F. van den; Bosch, Maurice A.A.J. van den; Lam, Marnix G.E.H. [University Medical Center Utrecht, Department of Radiology and Nuclear Medicine, Utrecht (Netherlands); Hillegersberg, Richard van [University Medical Center Utrecht, Department of Surgery, Utrecht (Netherlands); Sangro, Bruno [Clinica Universidad de Navarra-IDISNA and CIBEREHD, Liver Unit, Pamplona (Spain); Kao, Yung Hsiang [Cabrini Hospital, Department of Nuclear Medicine, Melbourne (Australia); Liu, Dave [Vancouver General Hospital, University of British Columbia, Department of Radiology, Vancouver, British Columbia (Canada); Louie, John D.; Sze, Daniel Y. [Stanford University Medical Center, Division of Interventional Radiology, Stanford (United States); Rose, Steven C. [University of California, Department of Radiology, San Diego (United States); Brown, Daniel B. [Vanderbilt University, Medical Center North, Department of Radiology, Nashville (United States); Ahmadzadehfar, Hojjat [University Hospital Bonn, Department of Nuclear Medicine, Bonn (Germany); Kim, Edward [Icahn School of Medicine at Mount Sinai, Division of Vascular and Interventional Radiology, New York (United States)

2017-12-15

Guidelines on how to adjust activity in patients with a history of liver surgery who are undergoing yttrium-90 radioembolisation ({sup 90}Y-RE) are lacking. The aim was to study the variability in activity prescription in these patients, between centres with extensive experience using resin microspheres {sup 90}Y-RE, and to draw recommendations on activity prescription based on an expert consensus. The variability in activity prescription between centres was investigated by a survey of international experts in the field of {sup 90}Y-RE. Six representative post-surgical patients (i.e. comparable activity prescription, different outcome) were selected. Information on patients' disease characteristics and data needed for activity calculation was presented to the expert panel. Reported was the used method for activity prescription and whether, how and why activity reduction was found indicated. Ten experts took part in the survey. Recommendations on activity reduction were highly variable between the expert panel. The median intra-patient range was 44 Gy (range 18-55 Gy). Reductions in prescribed activity were recommended in 68% of the cases. In consensus, a maximum D{sub Target} of 50 Gy was recommended. With a current lack of guidelines, large variability in activity prescription in post-surgical patients undergoing {sup 90}Y-RE exists. In consensus, D{sub Target} ≤50 Gy is recommended. (orig.)

Influence of potassium on the competition between methane and ethane in steam reforming over Pt supported on yttrium-stabilized zirconia.

NARCIS (Netherlands)

Graf, P.O.; Mojet, Barbara; Lefferts, Leonardus

2008-01-01

effect of addition of potassium to Pt supported on yttrium-stabilized zirconia (PtYSZ) catalyst for steam reforming of methane, ethane and methane/ethane mixtures was explored. Addition of potassium has a positive effect on preferential steam reforming of methane in mixtures of methane and ethane

Aspects of radiation protection during the treatment of liver cancer using yttrium-90 labelled microspheres

International Nuclear Information System (INIS)

Klemp, P.F.B.; Perry, A.M.; Fox, R.A.; Gray, B.N.; Burton, M.A.

1989-01-01

Twenty eight patients have received treatment for liver cancer by the intra-hepatic arterial injection of between 1 and 4 GBq of yttrium-90 labelled microspheres. The injection was performed at laparotomy. If 11.1 MBq of yttrium-90 are distributed evenly over 1 sq cm of tissue, the tissue surface will suffer an initial beta dose rate of 16.2 Gy h -1 . Special precautions are therefore essential during the injection procedure, subsequently in nursing the patient and if further intervention becomes necessary. A specially designed apparatus is used for the injection, glass spectacles are worn and if the active liver is to be handled, lead rubber gloves are used. The theatre is prepared so that contaminated items can be easily isolated and a 'spill pack' is readily available. At completion of the operation, the bremsstrahlung dose rate at 15 cm from the liver is initially 15 μSv h -1 GBq -1 . Contamination of urine is typically 20 to 50 kBq L -1 while the contamination of other body fluids is negligible. Finger doses to the surgeons has varied from 2 to 5 mSv GBq -1 injected while personnel film badges used to monitor the dose equivalent to the surgeons and ward staff have recorded maximum doses of 1.5 mSv and 300 μSv respectively. 11 refs., 1 fig., 3 tabs

Growth of rare-earth doped single crystal yttrium aluminum garnet fibers

Science.gov (United States)

Bera, Subhabrata; Nie, Craig D.; Harrington, James A.; Cheng, Long; Rand, Stephen C.; Li, Yuan; Johnson, Eric G.

2018-02-01

Rare-earth doped single crystal (SC) yttrium aluminum garnet (YAG) fibers have great potential as high-power laser gain media. SC fibers combine the superior material properties of crystals with the advantages of a fiber geometry. Improving processing techniques, growth of low-loss YAG SC fibers have been reported. A low-cost technique that allows for the growth of optical quality Ho:YAG single crystal (SC) fibers with different dopant concentrations have been developed and discussed. This technique is a low-cost sol-gel based method which offers greater flexibility in terms of dopant concentration. Self-segregation of Nd ions in YAG SC fibers have been observed. Such a phenomenon can be utilized to fabricate monolithic SC fibers with graded index.

Measurement of induced radioactivity in a spallation neutron field of a mercury target for GeV-proton bombardment

International Nuclear Information System (INIS)

Kasugai, Y.; Takada, H.; Nakashima, H.

2001-01-01

An integral experiment on radioactivity induced in spallation neutron fields was carried out under the ASTE (AGS-Spallation Target Experiment) collaboration using AGS (Alternative Gradient Synchrotron) at BNL (Brookhaven National Laboratory). The spallation neutrons were produced by bombarding a mercury target with protons of 1.6, 12 and 24 GeV. The number of protons was 3 - 4 x 10 13 for each irradiation. The irradiated materials were titanium, nickel, cobalt, yttrium, and bismuth, and placed on the cylindrical surface of the mercury target at the distance of 15 - 16 cm from the beam-incident-surface of the target. Disintegration rates of induced radioactivities were measured at several cooling-time ranging from hours to months. The principal nuclides contributing to the radioactivity were pointed out for each material. The experimental results for bismuth were compared with the calculations with DCAHIN-SP code. (author)

Coupling of erbium dopants to yttrium orthosilicate photonic crystal cavities for on-chip optical quantum memories

Energy Technology Data Exchange (ETDEWEB)

Miyazono, Evan; Zhong, Tian; Craiciu, Ioana; Kindem, Jonathan M.; Faraon, Andrei, E-mail: faraon@caltech.edu [T. J. Watson Laboratory of Applied Physics, California Institute of Technology, 1200 E California Blvd, Pasadena, California 91125 (United States)

2016-01-04

Erbium dopants in crystals exhibit highly coherent optical transitions well suited for solid-state optical quantum memories operating in the telecom band. Here, we demonstrate coupling of erbium dopant ions in yttrium orthosilicate to a photonic crystal cavity fabricated directly in the host crystal using focused ion beam milling. The coupling leads to reduction of the photoluminescence lifetime and enhancement of the optical depth in microns-long devices, which will enable on-chip quantum memories.

Direct observation of magnon-phonon coupling in yttrium iron garnet

Science.gov (United States)

Man, Haoran; Shi, Zhong; Xu, Guangyong; Xu, Yadong; Chen, Xi; Sullivan, Sean; Zhou, Jianshi; Xia, Ke; Shi, Jing; Dai, Pengcheng

2017-09-01

The magnetic insulator yttrium iron garnet (YIG) with a ferrimagnetic transition temperature of ˜560 K has been widely used in microwave and spintronic devices. Anomalous features in spin Seeback effect (SSE) voltages have been observed in Pt/YIG and attributed to magnon-phonon coupling. Here, we use inelastic neutron scattering to map out low-energy spin waves and acoustic phonons of YIG at 100 K as a function of increasing magnetic field. By comparing the zero and 9.1 T data, we find that instead of splitting and opening up gaps at the spin wave and acoustic phonon dispersion intersecting points, magnon-phonon coupling in YIG enhances the hybridized scattering intensity. These results are different from expectations of conventional spin-lattice coupling, calling for different paradigms to understand the scattering process of magnon-phonon interactions and the resulting magnon polarons.

Treatment of persistent knee effusions with Yttrium 90

International Nuclear Information System (INIS)

Bouyoucef, S.E.; Drahmoune, R.; Mechken, F.; Amimour, A.; Hanni-Haddam, F.; Abtroun, F.; Sellah, M.; Mansouri, B.

2002-01-01

Yttrium 90 intra-articular injection is used in persisting active joint of the knee, where medication has failed to resolve chronic inflammation. The effective dose delivered to the synovia is linked to Y 90 activity and depends on the size of the joint space, the synovial structure and thickness and the inflammatory activity of the synovitis. The amount of the injected activity of Y90 was estimated according the volume effusion in 28 pathologic knee of 18 patients aged 18 years and more (mean age 46 years). All patients have persistent knee effusions and most of them have rheumatoid arthritis but others had ankylosing spondylitis, Behcet disease, psoriatic arthritis. According the radiological classification of Steinbrocker, 19 pathological knees were in stage 1, 5 in stage 2 and 4 in stage 3. The mean value of the monthly removed volume of the synovial liquid from the pathological knee was determined during the last month preceding the radiosynoviorthesis and four groups were identified: V0 no evidence of effusion liquid, 0 ml 100ml. The activity of Y 90 was estimated in order to obtain a total of 100 Gray in the envelope of 3 spherical phantoms with the same range of volume as defined above. The lowest activity of Y90, 111 MBq (3mCi) was determined for V0 according a mean value of standard sizes of knees. An activity of 18 MBq (0.5mCi) was added for each stage of 50 ml, so 129 MBq (3.5 mCi) for G1, 148 MBq (4 mCi) for G2 and 166 MBq (4.5 mCi) for G3. Efficacy of Y90 treatment was clinically assessed in all patients according to three parameters: pain, hydrarthrosis and range of joint movement at 1, 3, 6 and 12 months. The results were excellent in 13 knees and good in 9 and for most of them the efficacy of Y 90 was observed after 6 months. The results were less good in 3 knees but with an initial good evolution for all at 1 month. For 4 knees, the efficacy of Y 90 was bad. Although the small number of patients, these results show a high rate, 75%, of successful

Field and power dependence of auto-oscillations in yttrium-iron-garnet films

International Nuclear Information System (INIS)

McMichael, R.D.; Wigen, P.E.

1988-01-01

The nonlinear response of the magnetic spin system in yttrium-iron-garnet (YIG) thin films to high-power ferromagnetic resonance (FMR) at perpendicular resonance was studied and the results are presented. A diagram of the regions of auto-oscillation of the system as a function of field and power is presented which shows the modes that appear in low-power FMR becoming unstable to auto-oscillations with increased power. The auto-oscillations exhibit periodic, quasiperiodic, period doubling, and chaotic behavior with typical frequencies in the MHz range. The domains of oscillatory behavior due to individual resonance modes are seen to merge and shift to lower fields as power is increased. Possible mechanisms for the behavior are proposed

Yttrium silicate as an oxidation protection layer for C/C-SiC materials. Synthesis, electrophoretic deposition and high temperature oxidation; Yttriumsilikat als Oxidationsschutzschicht fuer C/C-SiC-Werkstoffe. Synthese, elektrophoretische Abscheidung und Hochtemperaturoxidation

Energy Technology Data Exchange (ETDEWEB)

Grosse-Brauckmann, Jana

2012-07-01

Carbon fibre reinforced carbon composites are promising materials for high temperature applications. They exhibit excellent thermal shock resistance and nearly constant mechanical strength. A serious draw-back of this material is their poor resistivity towards oxidation at temperatures above 400 C. To make use of the very good thermal stability the material needs an outer oxidation protection coating. Silicon carbide has been successfully employed at temperatures up to 1300 C. To increase the application range towards higher temperatures an outer environmental barrier coating is needed. In the present work yttrium silicates were used to complement the silicon carbide coated carbon fibre reinforced carbon material. Both stable compounds in the quasi-binary system Y{sub 2}O{sub 3}-SiO{sub 2}, yttrium orthosilicate (Y{sub 2}SiO{sub 5}) and yttrium pyrosilicate (Y{sub 2}Si{sub 2}O{sub 7}), were separately applied to the test samples via electrophoretic deposition. Suitable suspensions were prepared in butanone with iodine as charging agent to adjust conductivity and particle charge. Galvanostatic deposition obeys a linear growth law for the selected deposition times. Alternatively the feasibility of direct electrophoretic deposition from an yttrium silicate precursor sol was tested. Emphasis was put on the development of a suitable sol-system based on alkoxide precursors. Samples coated either with Y{sub 2}SiO{sub 5} or Y{sub 2}Si{sub 2}O{sub 7} were investigated using thermogravimetric high temperature oxidation in the temperature range from 1450 C to 1650 C, respectively. The coated samples exhibited very good oxidation resistance up to temperatures of 1600 C, while the performance was reduced at 1650 C to a few hours. All samples showed a parabolic mass increase with time indicating a diffusion limited process governing the oxidation kinetics. The cross sections of the samples show a sharp border between the SiO{sub 2} that crystallizes to cristobalite and the

49 CFR 393.89 - Buses, driveshaft protection.

Science.gov (United States)

2010-10-01

... ACCESSORIES NECESSARY FOR SAFE OPERATION Miscellaneous Parts and Accessories § 393.89 Buses, driveshaft protection. Any driveshaft extending lengthways under the floor of the passenger compartment of a bus shall... 49 Transportation 5 2010-10-01 2010-10-01 false Buses, driveshaft protection. 393.89 Section 393...

40 CFR 89.317 - NOX converter check.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false NOX converter check. 89.317 Section 89.317 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED..., the chemiluminescent oxides of nitrogen analyzer shall be checked for NO2 to NO converter efficiency...

40 CFR 89.105 - Certificate of conformity.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Certificate of conformity. 89.105... and Certification Provisions § 89.105 Certificate of conformity. Every manufacturer of a new nonroad compression-ignition engine must obtain a certificate of conformity covering the engine family, as described...

Yttrium-90 microsphere induced gastrointestinal tract ulceration

Directory of Open Access Journals (Sweden)

Rikabi Ali A

2008-09-01

Full Text Available Abstract Background Radiomicrosphere therapy (RT utilizing yttrium-90 (90Y microspheres has been shown to be an effective regional treatment for primary and secondary hepatic malignancies. We sought to determine a large academic institution's experience regarding the extent and frequency of gastrointestinal complications. Methods Between 2004 and 2007, 27 patients underwent RT for primary or secondary hepatic malignancies. Charts were subsequently reviewed to determine the incidence and severity of GI ulceration. Results Three patients presented with gastrointestinal bleeding and underwent upper endoscopy. Review of the pretreatment angiograms showed normal vascular anatomy in one patient, sclerosed hepatic vasculature in a patient who had undergone prior chemoembolization in a second, and an aberrant left hepatic artery in a third. None had undergone prophylactic gastroduodenal artery embolization. Endoscopic findings included erythema, mucosal erosions, and large gastric ulcers. Microspheres were visible on endoscopic biopsy. In two patients, gastric ulcers were persistent at the time of repeat endoscopy 1–4 months later despite proton pump inhibitor therapy. One elderly patient who refused surgical intervention died from recurrent hemorrhage. Conclusion Gastrointestinal ulceration is a known yet rarely reported complication of 90Y microsphere embolization with potentially life-threatening consequences. Once diagnosed, refractory ulcers should be considered for aggressive surgical management.

Bonding mechanism of a yttrium iron garnet film on Si without the use of an intermediate layer

International Nuclear Information System (INIS)

Pantzas, Konstantinos; Patriarche, Gilles; Talneau, Anne; Youssef, Jamal Ben

2014-01-01

Direct bonding of yttrium iron garnet (YIG) on silicon without the use of an intermediate bonding layer is demonstrated and characterized using scanning transmission electron microscopy and energy-dispersive x-ray spectroscopy. During the bonding experiment, the garnet is reduced in the presence of oxide-free silicon. As a result, a 5 nm thick SiO 2 /amorphous-YIG bilayer is formed and welds the garnet to silicon.

The accumulation and elimination of 89Sr in tea leaves

International Nuclear Information System (INIS)

Zhang Yongxi; Wang Shouxiang; Chen Chuanqun; Sun Zhiming; Hu Bingmin; Huang Dan

1995-01-01

The 89 Sr was added to the tea tree-soil system by different ways. The 89 Sr in the system through the over-ground part of tea tree, was much more than that through soil. The 89 Sr concentration in older leaves was higher than in shoot for a definite treatment. The accumulation elimination law of 89 Sr in leaves varied with the treatments. For the treatment through the over-ground part, the 89 Sr concentration in older leaves and shoot was monotonously decreased with time increasing. But for the treatment through soil the 89 Sr concentration in shoot was increased to reach a peak value, and then decreased slowly; while the 89 Sr concentration in older leaves increased quickly in a period, then increased slowly to attain a saturated value. In addition, the concentration factor of 89 Sr in older leaves and shoot were determined

40 CFR 89.908 - National security exemption.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false National security exemption. 89.908... Provisions § 89.908 National security exemption. (a)(1) Any nonroad engine, otherwise subject to this part... regulations for purposes of national security. No request for exemption is necessary. (2) Manufacturers may...

9 CFR 89.1 - Amount of feed.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Amount of feed. 89.1 Section 89.1 Animals and Animal Products ANIMAL AND PLANT HEALTH INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE INTERSTATE TRANSPORTATION OF ANIMALS (INCLUDING POULTRY) AND ANIMAL PRODUCTS STATEMENT OF POLICY UNDER THE...

Alkylation of pyridines at their 4-positions with styrenes plus yttrium reagent or benzyl Grignard reagents.

Science.gov (United States)

Mizumori, Tomoya; Hata, Takeshi; Urabe, Hirokazu

2015-01-02

A new regioselective alkylation of pyridines at their 4-position was achieved with styrenes in the presence of yttrium trichloride, BuLi, and diisobutylaluminium hydride (DIBAL-H) in THF. Alternatively, similar products were more simply prepared from pyridines and benzyl Grignard reagents. These reactions are not only a useful preparation of 4-substituted pyridines but are also complementary to other relevant reactions usually giving 2-substituted pyridines. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

40 CFR 89.325 - Engine intake air temperature measurement.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine intake air temperature measurement. 89.325 Section 89.325 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Test Equipment Provisions § 89.325 Engine intake air temperature measurement. (a) Engine intake air...

40 CFR 89.321 - Oxides of nitrogen analyzer calibration.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Oxides of nitrogen analyzer calibration. 89.321 Section 89.321 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Test Equipment Provisions § 89.321 Oxides of nitrogen analyzer calibration. (a) The chemiluminescent...

Nature of the magnetic susceptibility of dysprosium. Paramagnetic susceptibility of dysprosium - yttrium alloys

International Nuclear Information System (INIS)

Demidov, V.G.; Levitin, R.Z.; Chistyakov, O.D.

1976-01-01

The paramagnetic susceptibility of single crystals of dysprosium-yttirum alloys is measured in the basal plane and along the hexagonal axis. It is shown that the susceptibility of the alloys obeys the Curie-Weiss law, the effective magnetic moments allong the different directions being the same and the paramagnetic Curie temperatures being different. The difference between the paramagnetic Curie temperatures in the basal plane and along the hexagonal axis is independent of the dysprosium concentration in the alloy. As a comparison with the theoretical models of magnetic anisotropy shows, this is an indication that the magnetic anisotropy of dysprosium - yttrium alloys is of a single-ion nature

Fractional erbium-doped yttrium aluminum garnet laser-assisted drug delivery of hydroquinone in the treatment of melasma

Science.gov (United States)

Badawi, Ashraf M; Osman, Mai Abdelraouf

2018-01-01

Background Melasma is a difficult-to-treat hyperpigmentary disorder. Ablative fractional laser (AFL)-assisted delivery of topically applied drugs to varied targets in the skin has been an area of ongoing study and research. Objective The objective of this study was to evaluate the efficacy and safety of fractional erbium-doped yttrium aluminum garnet (Er:YAG) laser as an assisted drug delivery for enhancing topical hydroquinone (HQ) permeation into the skin of melasma patients. Patients and methods Thirty female patients with bilateral melasma were randomly treated in a split-face controlled manner with a fractional Er:YAG laser followed by 4% HQ cream on one side and 4% HQ cream alone on the other side. All patients received six laser sessions with a 2-week interval. The efficacy of treatments was determined through photographs, dermoscopic photomicrographs and Melasma Area Severity Index (MASI) score, all performed at baseline and at 12 weeks of starting therapy. The patient’s level of satisfaction was also recorded. Results Er:YAG laser + HQ showed significantly better results (plaser + HQ side vs HQ side. Minor reversible side effects were observed on both sides. Conclusion AFL-assisted delivery of HQ is a safe and effective method for the treatment of melasma. PMID:29379308

89Zr-Oxine Complex PET Cell Imaging in Monitoring Cell-based Therapies

Science.gov (United States)

Wu, Haitao; Asiedu, Kingsley O.; Szajek, Lawrence P.; Griffiths, Gary L.; Choyke, Peter L.

2015-01-01

Purpose To develop a clinically translatable method of cell labeling with zirconium 89 (89Zr) and oxine to track cells with positron emission tomography (PET) in mouse models of cell-based therapy. Materials and Methods This study was approved by the institutional animal care committee. 89Zr-oxine complex was synthesized in an aqueous solution. Cell labeling conditions were optimized by using EL4 mouse lymphoma cells, and labeling efficiency was examined by using dendritic cells (DCs) (n = 4), naïve (n = 3) and activated (n = 3) cytotoxic T cells (CTLs), and natural killer (NK) (n = 4), bone marrow (n = 4), and EL4 (n = 4) cells. The effect of 89Zr labeling on cell survival, proliferation, and function were evaluated by using DCs (n = 3) and CTLs (n = 3). Labeled DCs (444–555 kBq/[5 × 106] cells, n = 5) and CTLs (185 kBq/[5 × 106] cells, n = 3) transferred to mice were tracked with microPET/CT. In a melanoma immunotherapy model, tumor targeting and cytotoxic function of labeled CTLs were evaluated with imaging (248.5 kBq/[7.7 × 106] cells, n = 4) and by measuring the tumor size (n = 6). Two-way analysis of variance was used to compare labeling conditions, the Wilcoxon test was used to assess cell survival and proliferation, and Holm-Sidak multiple tests were used to assess tumor growth and perform biodistribution analyses. Results 89Zr-oxine complex was synthesized at a mean yield of 97.3% ± 2.8 (standard deviation). It readily labeled cells at room temperature or 4°C in phosphate-buffered saline (labeling efficiency range, 13.0%–43.9%) and was stably retained (83.5% ± 1.8 retention on day 5 in DCs). Labeling did not affect the viability of DCs and CTLs when compared with nonlabeled control mice (P > .05), nor did it affect functionality. 89Zr-oxine complex enabled extended cell tracking for 7 days. Labeled tumor-specific CTLs accumulated in the tumor (4.6% on day 7) and induced tumor regression (P cell tracking technique for use with PET that is

(89)Zr-Oxine Complex PET Cell Imaging in Monitoring Cell-based Therapies.

Science.gov (United States)

Sato, Noriko; Wu, Haitao; Asiedu, Kingsley O; Szajek, Lawrence P; Griffiths, Gary L; Choyke, Peter L

2015-05-01

To develop a clinically translatable method of cell labeling with zirconium 89 ((89)Zr) and oxine to track cells with positron emission tomography (PET) in mouse models of cell-based therapy. This study was approved by the institutional animal care committee. (89)Zr-oxine complex was synthesized in an aqueous solution. Cell labeling conditions were optimized by using EL4 mouse lymphoma cells, and labeling efficiency was examined by using dendritic cells (DCs) (n = 4), naïve (n = 3) and activated (n = 3) cytotoxic T cells (CTLs), and natural killer (NK) (n = 4), bone marrow (n = 4), and EL4 (n = 4) cells. The effect of (89)Zr labeling on cell survival, proliferation, and function were evaluated by using DCs (n = 3) and CTLs (n = 3). Labeled DCs (444-555 kBq/[5 × 10(6)] cells, n = 5) and CTLs (185 kBq/[5 × 10(6)] cells, n = 3) transferred to mice were tracked with microPET/CT. In a melanoma immunotherapy model, tumor targeting and cytotoxic function of labeled CTLs were evaluated with imaging (248.5 kBq/[7.7 × 10(6)] cells, n = 4) and by measuring the tumor size (n = 6). Two-way analysis of variance was used to compare labeling conditions, the Wilcoxon test was used to assess cell survival and proliferation, and Holm-Sidak multiple tests were used to assess tumor growth and perform biodistribution analyses. (89)Zr-oxine complex was synthesized at a mean yield of 97.3% ± 2.8 (standard deviation). It readily labeled cells at room temperature or 4°C in phosphate-buffered saline (labeling efficiency range, 13.0%-43.9%) and was stably retained (83.5% ± 1.8 retention on day 5 in DCs). Labeling did not affect the viability of DCs and CTLs when compared with nonlabeled control mice (P > .05), nor did it affect functionality. (89)Zr-oxine complex enabled extended cell tracking for 7 days. Labeled tumor-specific CTLs accumulated in the tumor (4.6% on day 7) and induced tumor regression (P cell tracking technique for use with PET that is applicable to a broad range of

Growth and characterization of yttrium iron garnet films on Si substrates by Chemical Solution Deposition (CSD) technique

Energy Technology Data Exchange (ETDEWEB)

Guo, Xin; Chen, Ying; Wang, Genshui [Key Laboratory of Inorganic Function Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, University of Chinese Academy of Sciences, 1295 Dingxi Rd., Shanghai 200050 (China); Zhang, Yuanyuan [Key Laboratory of Polar Materials and Devices, Ministry of Education, Department of Electronic Engineering, East China Normal University, 500 Dongchuan Rd., Shanghai 200241 (China); Ge, Jun [Key Laboratory of Inorganic Function Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, University of Chinese Academy of Sciences, 1295 Dingxi Rd., Shanghai 200050 (China); Tang, Xiaodong [Key Laboratory of Polar Materials and Devices, Ministry of Education, Department of Electronic Engineering, East China Normal University, 500 Dongchuan Rd., Shanghai 200241 (China); Ponchel, Freddy; Rémiens, Denis [Institute of Electronics, Microelectronics and Nanotechnology (IEMN)–DOAE, UMR CNRS 8520, Université des Sciences et Technologies de Lille, 59652 Villeneuve d’Ascq Cedex (France); Dong, Xianlin, E-mail: xldong@mail.sic.ac.cn [Key Laboratory of Inorganic Function Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, University of Chinese Academy of Sciences, 1295 Dingxi Rd., Shanghai 200050 (China)

2016-06-25

Yttrium Iron Garnet (YIG) films were prepared on Si substrates by Chemical Solution Deposition (CSD) technique using acetic acid and deionized water as solvents. Well-crystallized and crack-free YIG films were obtained when annealed at 750 °C and 850 °C respectively, showing a low surface roughness of several nanometers. When annealed at 750 °C for 30 min, the saturated magnetization (Ms) and coercive field (Hc) of YIG films were 0.121 emu/mm{sup 3} (4πMs = 1.52 kGs) and 7 Oe respectively, which were similar to that prepared by PLD technique. The peak-to-peak linewidth of ferromagnetic resonance (FMR) was 220 Oe at 9.10 GHz. The results demonstrated that CSD was an excellent technique to prepare high quality yttrium iron garnet (YIG) films on silicon, which could provide a lower-cost way for large-scale production on Si-based integrated devices. - Highlights: • The preparation of YIG films by Chemical Solution Deposition are demonstrated. • Well-crystallized and crack-free YIG films can be obtained on Si substrate by CSD. • YIG films can be crystallized in 750 °C with good magnetic performances. • It's beneficial to large-scale production of YIG films on Si integrated devices.

Synthesis of zirconia sol stabilized by trivalent cations (yttrium and neodymium or americium): a precursor for Am-bearing cubic stabilized zirconia.

Science.gov (United States)

Lemonnier, Stephane; Grandjean, Stephane; Robisson, Anne-Charlotte; Jolivet, Jean-Pierre

2010-03-07

Recent concepts for nuclear fuel and targets for transmuting long-lived radionuclides (minor actinides) and for the development of innovative Gen-IV nuclear fuel cycles imply fabricating host phases for actinide or mixed actinide compounds. Cubic stabilized zirconia (Zr, Y, Am)O(2-x) is one of the mixed phases tested in transmutation experiments. Wet chemical routes as an alternative to the powder metallurgy are being investigated to obtain the required phases while minimizing the handling of contaminating radioactive powder. Hydrolysis of zirconium, neodymium (a typical surrogate for americium) and yttrium in aqueous media in the presence of acetylacetone was firstly investigated. Progressive hydrolysis of zirconium acetylacetonate and sorption of trivalent cations and acacH on the zirconia particles led to a stable dispersion of nanoparticles (5-7 nm) in the 6-7 pH range. This sol gels with time or with temperature. The application to americium-containing solutions was then successfully tested: a stable sol was synthesized, characterized and used to prepare cubic stabilized zirconia (Zr, Y, Am)O(2-x).

Phonon-impurity relaxation and acoustic wave absorption in yttrium-aluminium garnet crystals with impurities

International Nuclear Information System (INIS)

Ivanov, S.N.; Kotelyanskij, I.M.; Medved', V.V.

1983-01-01

The experimental results of investigations of the influence of substitution impurities in the yttrium-aluminium garnet lattice on absorption of high-frequency acoustic waves are presented. It is shown that the phonon-impurity relaxation processses affect at most the wave absorption and have resonance character when the acoustic wave interacts with the thermal phonon group in the vicinity of the perturbed part of the phonon spectrum caused by the impurity. The differences of time values between inelastic and elastic thermal phonons relaxations determined from the data on longitudinal and shear waves in pure and impurity garnet crystals are discussed

Measurement of induced radioactivity in a spallation neutron field of a mercury target for GeV-proton bombardment

Energy Technology Data Exchange (ETDEWEB)

Kasugai, Y.; Takada, H.; Nakashima, H. [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment] [and others

2001-03-01

An integral experiment on radioactivity induced in spallation neutron fields was carried out under the ASTE (AGS-Spallation Target Experiment) collaboration using AGS (Alternative Gradient Synchrotron) at BNL (Brookhaven National Laboratory). The spallation neutrons were produced by bombarding a mercury target with protons of 1.6, 12 and 24 GeV. The number of protons was 3 - 4 x 10{sup 13} for each irradiation. The irradiated materials were titanium, nickel, cobalt, yttrium, and bismuth, and placed on the cylindrical surface of the mercury target at the distance of 15 - 16 cm from the beam-incident-surface of the target. Disintegration rates of induced radioactivities were measured at several cooling-time ranging from hours to months. The principal nuclides contributing to the radioactivity were pointed out for each material. The experimental results for bismuth were compared with the calculations with DCAHIN-SP code. (author)

AXAIR89Q User's Manual

International Nuclear Information System (INIS)

Simpkins, A.A.

1994-04-01

AXAIR89Q is the primary dose assessment code used at the Savannah River Site to predict downwind doses following a hypothetical atmospheric release of relatively short duration. The primary purpose of the code is to perform calculations for safety-related documentation, and there is strict adherence in AXAIR89Q to the guidance in USNRC Regulatory Guide 1.145 (USNRC, 1983) entitled Atmospheric Dispersion Models for Potential Accident Consequence Assessments at Nuclear Power Plants. Doses are determined for the cloud shine, and inhalation pathways. Ingestion and ground shine are not considered. Future modifications are expected to include these features. This report discusses the information needed to execute the program and interpret the results

Structural and dielectric properties of yttrium-substituted hydroxyapatites

Energy Technology Data Exchange (ETDEWEB)

Kaygili, Omer, E-mail: okaygili@firat.edu.tr [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Dorozhkin, Sergey V. [Kudrinskaja sq. 1-155, 123242 Moscow (Russian Federation); Ates, Tankut [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Canan Gursoy, N. [Department of Microbiology and Clinic Microbiology, Inonu University, 44280 Malatya (Turkey); Keser, Serhat [Department of Chemistry, Faculty of Science, Firat University, 23119 Elazig (Turkey); Yakuphanoglu, Fahrettin [Department of Physics, Faculty of Science, Firat University, 23119 Elazig (Turkey); Birkan Selçuk, A. [Technology Department, Saraykoy Nuclear Research and Training Centre, 06983 Ankara (Turkey)

2015-02-01

Hydroxyapatite (HAp) samples doped with 0, 2 and 4 at.% of yttrium (Y) were characterized using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy attached with energy dispersive X-ray (EDX) spectroscopy, antimicrobial activity tests and dielectric studies. The hydroxyl groups observed in FTIR spectra confirmed the formation of HAp phase in the studied samples. The crystallite size, crystallinity degree and lattice parameters of the samples were changed with Y content. The volume of the unit cell was gradually decreased with the addition of Y. Undoped and Y-containing HAp samples were screened to determine their in vitro antimicrobial activities against the standard strains. It was found that no samples have any antimicrobial effect. The relative dielectric permittivity and dielectric loss are affected by Y content. While the alternating current conductivity increases with increasing frequency, it decreases with increasing Y content. - Highlights: • The lattice parameters and crystal size are affected by Y content. • The volume of the unit cell was gradually decreased with the addition of Y. • No samples have any antimicrobial effect. • The alternating current conductivity decreases with increasing Y content.

Structural and dielectric properties of yttrium-substituted hydroxyapatites

International Nuclear Information System (INIS)

Kaygili, Omer; Dorozhkin, Sergey V.; Ates, Tankut; Canan Gursoy, N.; Keser, Serhat; Yakuphanoglu, Fahrettin; Birkan Selçuk, A.

2015-01-01

Hydroxyapatite (HAp) samples doped with 0, 2 and 4 at.% of yttrium (Y) were characterized using X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy attached with energy dispersive X-ray (EDX) spectroscopy, antimicrobial activity tests and dielectric studies. The hydroxyl groups observed in FTIR spectra confirmed the formation of HAp phase in the studied samples. The crystallite size, crystallinity degree and lattice parameters of the samples were changed with Y content. The volume of the unit cell was gradually decreased with the addition of Y. Undoped and Y-containing HAp samples were screened to determine their in vitro antimicrobial activities against the standard strains. It was found that no samples have any antimicrobial effect. The relative dielectric permittivity and dielectric loss are affected by Y content. While the alternating current conductivity increases with increasing frequency, it decreases with increasing Y content. - Highlights: • The lattice parameters and crystal size are affected by Y content. • The volume of the unit cell was gradually decreased with the addition of Y. • No samples have any antimicrobial effect. • The alternating current conductivity decreases with increasing Y content

EURALERT-89 user's guide

International Nuclear Information System (INIS)

Mueller, H.; Friedland, W.; Proehl, G.; Paretzke, H.G.

1990-09-01

EURALERT-89 is a dose assessment program system including countermeasures which has been developed in the framework of the C.E.C. research programme 'Radiological aspects of nuclear accident scenarios'. For this purpose the ECOSYS model for calculating the transfer of radionuclides through the environment, the contamination of foodstuffs and potential doses has been adapted to real-time use in the different European countries. In this user's guide the file names are given in the form SUBD/FNAM; this means that the data file with name FNAM is in the subdirectory SUBD. Remember that writing the path of a file depends on the computer used. With EURALERT-89 it is relatively simple to get an estimate of the most important informations (deposition, maximum specific activities in foodstuffs, most important dose values) for all locations which are included in the input file. This goal can be achieved with only a few commands. (orig./HP)

Evaluation of macrocyclic hydroxyisophthalamide ligands as chelators for zirconium-89.

Science.gov (United States)

Bhatt, Nikunj B; Pandya, Darpan N; Xu, Jide; Tatum, David; Magda, Darren; Wadas, Thaddeus J

2017-01-01

The development of bifunctional chelators (BFCs) for zirconium-89 immuno-PET applications is an area of active research. Herein we report the synthesis and evaluation of octadentate hydroxyisophthalamide ligands (1 and 2) as zirconium-89 chelators. While both radiometal complexes could be prepared quantitatively and with excellent specific activity, preparation of 89Zr-1 required elevated temperature and an increased reaction time. 89Zr-1 was more stable than 89Zr-2 when challenged in vitro by excess DTPA or serum proteins and in vivo during acute biodistribution studies. Differences in radiometal complex stability arise from structural changes between the two ligand systems, and suggest further ligand optimization is necessary to enhance 89Zr chelation.

Evaluation of macrocyclic hydroxyisophthalamide ligands as chelators for zirconium-89.

Directory of Open Access Journals (Sweden)

Nikunj B Bhatt

Full Text Available The development of bifunctional chelators (BFCs for zirconium-89 immuno-PET applications is an area of active research. Herein we report the synthesis and evaluation of octadentate hydroxyisophthalamide ligands (1 and 2 as zirconium-89 chelators. While both radiometal complexes could be prepared quantitatively and with excellent specific activity, preparation of 89Zr-1 required elevated temperature and an increased reaction time. 89Zr-1 was more stable than 89Zr-2 when challenged in vitro by excess DTPA or serum proteins and in vivo during acute biodistribution studies. Differences in radiometal complex stability arise from structural changes between the two ligand systems, and suggest further ligand optimization is necessary to enhance 89Zr chelation.

Treatment of diffuse large B-cell lymphoma of the liver with yttrium-90 microsphere embolization.

Science.gov (United States)

Fenske, Timothy S; Benjamin, Heather; Kroft, Steven H; Hohenwalter, Eric J; Rilling, William S

2008-11-01

A 41-year-old male with a 4-year history of chronic hepatitis C presented with a 1-month history of abdominal pain, fatigue, weight loss, and night sweats. Laboratory examinations, chest, abdomen, and pelvic CT scans, PET-CT scans, ultrasound-guided needle biopsies of liver lesions, bone-marrow biopsy, flow cytometry, and immunohistochemical staining for B-cell markers including CD20. Chemoresistant diffuse large B-cell lymphoma, with gradual loss of CD20 antigen expression. Embolization of hepatic tumors using yttrium-90 microspheres (Therasphere, Theragenics Corporation, Buford, GA).

Addition compounds of perchlorates from yttrium and lanthanides elements with the N,N,N',N'tetramethyl amide of phthalic acid

International Nuclear Information System (INIS)

Silva, C.P.G. da.

1974-01-01

The reaction between lanthanide perchlorates and yttrium with tetra methyl phthalamide (TMPA) was studied, and compounds of the general formula Ln (C 10 4 ) 3 . TMPA have been isolated. The compounds were characterized by analysis of their components, infra-red spectra, molar conductances in nitromethane and nitrobenzene, X ray powder patterns and thermal analysis. (author)

Combustion synthesis and photoluminescence in novel red emitting yttrium gadolinium pyrosilicate nanocrystalline phosphor

Energy Technology Data Exchange (ETDEWEB)

Hedaoo, V.P., E-mail: vraikwar@rediffmail.com [Department of Physics, R. J. College, Ghatkopar, Mumbai, MS 400086 (India); Bhatkar, V.B. [Department of Physics, Shri Shivaji Science College, Amravati, MS 444602 (India); Omanwar, S.K. [Department of Physics, SGB Amravati University, Amravati, MS 444602 (India)

2016-07-05

Yttrium Gadolinium Pyrosilicate Y{sub 2-x}Gd{sub x}Si{sub 2}O{sub 7}:Eu{sup 3+} (x = 0.05, 0.10, 0.15) phosphor powder was prepared by facile and time efficient modified combustion method for the first time. The phosphor was characterized by powder X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), photoluminescence excitation (PLE) and emission (PL) spectroscopy and color chromaticity coordinates. XRD revealed the monoclinic crystal structure with space group P1¯. The crystallite size was calculated by Williamson-Hall (W–H) analysis. Nanoplates-like morphology was observed in FESEM analysis with size in the range 50–80 nm. TEM images confirmed the particle size and shape. Upon excitation by 254 nm UV light, the phosphor showed the characteristic red emission peaks at 589 nm and 613 nm corresponding to {sup 5}D{sub 0} → {sup 7}F{sub 1} and {sup 5}D{sub 0} → {sup 7}F{sub 2} transitions respectively. It was observed that the nanocrystalline phosphor Y{sub 2-x}Gd{sub x}Si{sub 2}O{sub 7}:Eu{sup 3+}can be tuned to emit orange to red color by adjusting the ratio Y/Gd. This phosphor thus can be a potential candidate as orange to red color emitting tunable nanocrystalline phosphor for optical devices. - Highlights: • A novel Yttrium Gadolinium Pyrosilicate doped with Eu{sup 3+} is reported. • Facile and time efficient modified combustion method is used. • The nanocrystalline structure was shown by X-ray diffraction, W–H analysis. • FESEM and TEM images confirmed the nanocrystalline structure. • The reported phosphor can be tuned from orange to red by varying Y/Gd ratio.

Phase Diagram for Magnon Condensate in Yttrium Iron Garnet Film

Science.gov (United States)

Li, Fuxiang; Saslow, Wayne M.; Pokrovsky, Valery L.

2013-01-01

Recently, magnons, which are quasiparticles describing the collective motion of spins, were found to undergo Bose-Einstein condensation (BEC) at room temperature in films of Yttrium Iron Garnet (YIG). Unlike other quasiparticle BEC systems, this system has a spectrum with two degenerate minima, which makes it possible for the system to have two condensates in momentum space. Recent Brillouin Light Scattering studies for a microwave-pumped YIG film of thickness d = 5 μm and field H = 1 kOe find a low-contrast interference pattern at the characteristic wavevector Q of the magnon energy minimum. In this report, we show that this modulation pattern can be quantitatively explained as due to unequal but coherent Bose-Einstein condensation of magnons into the two energy minima. Our theory predicts a transition from a high-contrast symmetric state to a low-contrast non-symmetric state on varying the d and H, and a new type of collective oscillation. PMID:23455849

Platinum/yttrium iron garnet inverted structures for spin current transport

Energy Technology Data Exchange (ETDEWEB)

Aldosary, Mohammed; Li, Junxue; Tang, Chi; Xu, Yadong; Shi, Jing [Department of Physics and Astronomy and SHINES Energy Frontier Research Center, University of California, Riverside, California 92521 (United States); Zheng, Jian-Guo [Irvine Materials Research Institute, University of California, Irvine, California 92697 (United States); Bozhilov, Krassimir N. [Central Facility for Advanced Microscopy and Microanalysis, University of California, Riverside, California 92521 (United States)

2016-06-13

30-80 nm thick yttrium iron garnet (YIG) films are grown by pulsed laser deposition on a 5 nm thick sputtered Pt atop gadolinium gallium garnet substrate (GGG) (110). Upon post-growth rapid thermal annealing, single crystal YIG(110) emerges as if it were epitaxially grown on GGG(110) despite the presence of the intermediate Pt film. The YIG surface shows atomic steps with the root-mean-square roughness of 0.12 nm on flat terraces. Both Pt/YIG and GGG/Pt interfaces are atomically sharp. The resulting YIG(110) films show clear in-plane uniaxial magnetic anisotropy with a well-defined easy axis along 〈001〉 and a peak-to-peak ferromagnetic resonance linewidth of 7.5 Oe at 9.32 GHz, similar to YIG epitaxially grown on GGG. Both spin Hall magnetoresistance and longitudinal spin Seebeck effects in the inverted bilayers indicate excellent Pt/YIG interface quality.

The Dipeptidyl Peptidases 4, 8, and 9 in Mouse Monocytes and Macrophages: DPP8/9 Inhibition Attenuates M1 Macrophage Activation in Mice.

Science.gov (United States)

Waumans, Yannick; Vliegen, Gwendolyn; Maes, Lynn; Rombouts, Miche; Declerck, Ken; Van Der Veken, Pieter; Vanden Berghe, Wim; De Meyer, Guido R Y; Schrijvers, Dorien; De Meester, Ingrid

2016-02-01

Atherosclerosis remains the leading cause of death in Western countries. Dipeptidyl peptidase (DPP) 4 has emerged as a novel target for the prevention and treatment of atherosclerosis. Family members DPP8 and 9 are abundantly present in macrophage-rich regions of atherosclerotic plaques, and DPP9 inhibition attenuates activation of human M1 macrophages in vitro. Studying this family in a mouse model for atherosclerosis would greatly advance our knowledge regarding their potential as therapeutic targets. We found that DPP4 is downregulated during mouse monocyte-to-macrophage differentiation. DPP8 and 9 expression seems relatively low in mouse monocytes and macrophages. Viability of primary mouse macrophages is unaffected by DPP4 or DPP8/9 inhibition. Importantly, DPP8/9 inhibition attenuates macrophage activation as IL-6 secretion is significantly decreased. Mouse macrophages respond similarly to DPP inhibition, compared to human macrophages. This shows that the mouse could become a valid model species for the study of DPPs as therapeutic targets in atherosclerosis.

{sup 89}Zr-labeled nivolumab for imaging of T-cell infiltration in a humanized murine model of lung cancer

Energy Technology Data Exchange (ETDEWEB)

England, Christopher G.; Ehlerding, Emily B.; Ellison, Paul A.; Hernandez, Reinier; Barnhart, Todd E. [University of Wisconsin - Madison, Department of Medical Physics, Madison, WI (United States); Jiang, Dawei [Health Science Center, Shenzhen University, Guangdong Key Laboratory for Biomedical Measurements and Ultrasound Imaging, School of Biomedical Engineering, Guangzhou (China); University of Wisconsin - Madison, Department of Radiology, Madison, WI (United States); Rekoske, Brian T. [University of Wisconsin - Madison, Department of Medicine, Madison, WI (United States); McNeel, Douglas G. [University of Wisconsin - Madison, Department of Medicine, Madison, WI (United States); University of Wisconsin Carbone Cancer Center, Madison, WI (United States); Huang, Peng [Health Science Center, Shenzhen University, Guangdong Key Laboratory for Biomedical Measurements and Ultrasound Imaging, School of Biomedical Engineering, Guangzhou (China); Cai, Weibo [University of Wisconsin - Madison, Department of Medical Physics, Madison, WI (United States); University of Wisconsin - Madison, Department of Radiology, Madison, WI (United States); University of Wisconsin Carbone Cancer Center, Madison, WI (United States)

2018-01-15

Nivolumab is a human monoclonal antibody specific for programmed cell death-1 (PD-1), a negative regulator of T-cell activation and response. Acting as an immune checkpoint inhibitor, nivolumab binds to PD-1 expressed on the surface of many immune cells and prevents ligation by its natural ligands. Nivolumab is only effective in a subset of patients, and there is limited evidence supporting its use for diagnostic, monitoring, or stratification purposes. {sup 89}Zr-Df-nivolumab was synthesized to map the biodistribution of PD-1-expressing tumor infiltrating T-cells in vivo using a humanized murine model of lung cancer. The tracer was developed by radiolabeling the antibody with the positron emitter zirconium-89 ({sup 89}Zr). Imaging results were validated by ex vivo biodistribution studies, and PD-1 expression was validated by immunohistochemistry. Data obtained from PET imaging were used to determine human dosimetry estimations. The tracer showed elevated binding to stimulated PD-1 expressing T-cells in vitro and in vivo. PET imaging of {sup 89}Zr-Df-nivolumab allowed for clear delineation of subcutaneous tumors through targeting of localized activated T-cells expressing PD-1 in the tumors and salivary glands of humanized A549 tumor-bearing mice. In addition to tumor uptake, salivary and lacrimal gland infiltration of T-cells was noticeably visible and confirmed via histological analysis. These data support our claim that PD-1-targeted agents allow for tumor imaging in vivo, which may assist in the design and development of new immunotherapies. In the future, noninvasive imaging of immunotherapy biomarkers may assist in disease diagnostics, disease monitoring, and patient stratification. (orig.)

Trace determination of yttrium and some heavy rare-earths by adsorptive stripping voltammetry

International Nuclear Information System (INIS)

Wang, J.; Zadeii, J.M.

1986-01-01

The interfacial and redox behaviour of rare-earth chelates the Solochrome Violet RS are exploited for developing a sensitive adsorptive stripping procedure. Yttrium and heavy rare earths such as dysprosium, holmium and ytterbium can thus be measured at ng/ml levels and below, by controlled adsorptive accumulation of the metal chelate at the hanging mercury drop electrode, followed by voltammetric measurement of the surface species. With a 3-min preconcentration time, the detection limit ranges from 5 x 10 -10 to 1.4 x 10 -9 M. The relative standard deviation at the 7 ng/ml level ranges from 4 to 7%. A separation method is required to differentiate between the individual rare-earth metals. (author)

A study of an ion-exchange process for separation of strontium and yttrium

International Nuclear Information System (INIS)

Mubarek, M.A.

1980-01-01

A study has been carried out to determine optimum conditions for the separation of strontium and yttrium by ion-exchange. The parameters of interest for such separation such as the dimensions of the ion-exchange columns, flow rates through the columns and pH values of the solutions, which affect the overall yield in the process, have been investigated. Application of this method for routine quantitative determinations of Sr-90 in environmental samples, particularly the wet-ashed biological materials has also been studied. The method, although a rapid and convenient one has not been found to yield consistent results probably due to the requirement of stringent analytical controls during the process. (author)

Use of yttrium-90 hydroxyapatite radiosynovectomy as a primary modality of treatment in diffuse pigmented villonodular synovitis of the knee joint: A first case report

International Nuclear Information System (INIS)

Kamaleshwaran, Koramadai Karuppusamy; Rajan, David; Krishnan, Boopathi; Gounder, Thirumalaisamy Subbaih; Chakraborty, Sudipta; Kalarickal, Radhakrishnan; Mohanan, Vyshakh; Shinto, Ajit Sugunan

2015-01-01

Pigmented villonodular synovitis (PVNS) is a rare, relatively benign, intra-articular lesion characterized by a slowly progressive proliferation of synovial tissue. Knee is the most frequently involved joint. Localized and diffuse forms of synovial involvement were reported. In extensive diffuse cases, total synovectomy is needed, almost impossible to achieve. Hence, other treatment modalities such as intra-articular injection of yttrium-90 have been tried and shown to be effective in reducing the rate of local recurrence with “acceptable” joint damage. Radiosynovectomy is based on the irradiation of the joint synovium by the intra-articular administration of various β-emitting radiopharmaceuticals. We describe the first case report of use of yttrium-90 hydroxyapatite particulates in a 33-year-old male who presented with diffuse PVNS of knee joint as a primary modality of treatment

[Protein kinase A inhibitor H-89 blocks polyploidization of SP600125-induced CMK cells by regulating phosphorylation of ribosomal protein S6 kinase 1].

Science.gov (United States)

Zhao, Song; Yang, Jingang; Li, Changling; Xing, Sining; Yu, Ying; Liu, Shuo; Pu, Feifei; Ma, Dongchu

2016-10-01

Objective To investigate the regulatory effect of post-translation modification of ribosomal protein S6 kinase 1 (S6K1) on the polyploidization of megakaryocytes. Methods SP600125, a c-Jun N-terminal kinase (JNK) inhibitor, and H-89, a cAMP-dependent protein kinase (PKA) inhibitor, were used to treat CMK cells separately or in combination. With propidium iodide (PI) to dye DNA in the treated cells, the relative DNA content was detected by flow cytometry, and then the DNA polyploidy was analyzed. The change of expression and phosphorylation of ribosomal protein S6 kinase 1 (S6K1), an important mammalian target of rapamycin (mTOR) downstream target molecule, was analyzed by Western blotting. Molecular docking study and kinase activity assay were performed to analyze the combination of H-89 with S6K1 and the effect of H-89 on the activity of S6K1 kinase. Results SP600125 induced CMK cell polyploidization in a time-dependent and dose-dependent manner. At the same time, it increased the phosphorylation of S6K1 at Thr421/Ser424 and decreased the phosphorylation of S6K1 at Thr389. H-89 not only blocked polyploidization, but also decreased the phosphorylation of S6K1 at Thr421/Ser424 and increased the phosphorylation of S6K1 at Thr389. Molecular docking and kinase activity assay showed that H-89 occupied the ATP binding sites of S6K1 and inhibited its activity. Noticeably, both H-89 and SP600125 inhibited the activity of PKA. Moreover, the two drugs further inhibited the activity of PKA when used together. Therefore, these data indicated that H-89 blocked the SP600125-induced polyploidization of CMK cells mainly by changing S6K1 phosphorylation state, rather than its inhibitory effect on PKA. Conclusion H-89 can block the polyploidization of SP600125-induced CMK cells by regulating S6K1 phosphorylation state.

NMR investigation of the effect of hydrostate pressure on the local magnetic fields in Y6Fe23

International Nuclear Information System (INIS)

Vasil'kovskij, V.A.; Bartashevich, M.I.; Gorlenko, A.A.; Kovtun, N.M.; Kupriyanov, A.K.

1990-01-01

The local magnetic fields at the Y 89 and Fe 57 nuclei in the intermetallic compound Y 6 Fe 23 and their shift induced by pressure are investigated by the NMR technique. The results are discussed on the basis of a model in which the atomic magnetic moment for iron includes the moment of polarized collectivized electrons responsible for the chemical bond between yttrium and iron. It is shown that with decreasing concentration of yttrium in the Y x Fe y compounds delocalization of the iron magnetic electrons occurs

49 CFR 8.9 - Information Security Review Committee.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false Information Security Review Committee. 8.9 Section.../DECLASSIFICATION/ACCESS Classification/Declassification of Information § 8.9 Information Security Review Committee. (a) There is hereby established a Department of Transportation Information Security Review Committee...

The average baboon brain: MRI templates and tissue probability maps from 89 individuals.

Science.gov (United States)

Love, Scott A; Marie, Damien; Roth, Muriel; Lacoste, Romain; Nazarian, Bruno; Bertello, Alice; Coulon, Olivier; Anton, Jean-Luc; Meguerditchian, Adrien

2016-05-15

The baboon (Papio) brain is a remarkable model for investigating the brain. The current work aimed at creating a population-average baboon (Papio anubis) brain template and its left/right hemisphere symmetric version from a large sample of T1-weighted magnetic resonance images collected from 89 individuals. Averaging the prior probability maps output during the segmentation of each individual also produced the first baboon brain tissue probability maps for gray matter, white matter and cerebrospinal fluid. The templates and the tissue probability maps were created using state-of-the-art, freely available software tools and are being made freely and publicly available: http://www.nitrc.org/projects/haiko89/ or http://lpc.univ-amu.fr/spip.php?article589. It is hoped that these images will aid neuroimaging research of the baboon by, for example, providing a modern, high quality normalization target and accompanying standardized coordinate system as well as probabilistic priors that can be used during tissue segmentation. Copyright © 2016 Elsevier Inc. All rights reserved.

Determination of Sr-89/90

International Nuclear Information System (INIS)

Smodis, B.; Planinsek, Z.; Stegnar, P.

1995-01-01

Sample preparation and radiochemical analysis for the determination of Strontium 89 and Strontium 90 in various food and environmental samples including sediments, fruit and vegetables, milk, meat and fish is elaborated in this paper

Magnetophotonic crystals based on yttrium-iron-garnet infiltrated opals: Magnetization-induced second-harmonic generation

Science.gov (United States)

Murzina, T. V.; Kim, E. M.; Kapra, R. V.; Moshnina, I. V.; Aktsipetrov, O. A.; Kurdyukov, D. A.; Kaplan, S. F.; Golubev, V. G.; Bader, M. A.; Marowsky, G.

2006-01-01

Three-dimensional magnetophotonic crystals (MPCs) based on artificial opals infiltrated by yttrium iron garnet (YIG) are fabricated and their structural, optical, and nonlinear optical properties are studied. The formation of the crystalline YIG inside the opal matrix is checked by x-ray analysis. Two templates are used for the infiltration by YIG: bare opals and those covered by a thin platinum film. Optical second-harmonic generation (SHG) technique is used to study the magnetization-induced nonlinear-optical properties of the composed MPCs. A high nonlinear magneto-optical Kerr effect in the SHG intensity is observed at the edge of the photonic band gap of the MPCs.

The dynamics of accumulation and disappearance of 89Sr in tea

International Nuclear Information System (INIS)

Chen Chuanqun; Wang Shouxiang; Zhang Yongxi; Sun Zhiming

1994-06-01

The 89 Sr was put into a tea tree-soil system by different ways. The results showed that for 89 Sr put into the system through the above-ground 1 part of tea tree, its concentration in tea was much higher than that through soil. The concentration of 89 Sr in older tea was higher than that in shoot for the same treatment. The accumulation and disappearance of 89 Sr in tea varied with the treatments. For the treatment through the above-ground part, the concentrations of 89 Sr in older tea and shoot were monotonously decreasing with time. For the treatment through soil the concentration of 89 Sr in shoot increased initially to a maximum value, then decreased slowly; while the concentration of 89 Sr in older tea increased quickly in a definite period, then increased slowly to gain a saturated value. In addition, the values of concentration factor of 89 Sr in the older tea and shoot were determined, too

Yttrium-90 radioembolization using TheraSphere in the management of primary and secondary liver tumors.

Science.gov (United States)

Riaz, A; Lewandowski, R J; Kulik, L; Salem, R

2009-06-01

Locoregional therapies, such as transarterial chemoembolization, radioembolization and thermal ablation (e.g., radiofrequency ablation) are establishing their roles in the management of liver malignancies. With yYttrium-90 radioembolization therapy (90Y) radionuclide labeled microspheres are injected into the tumor feeding artery. This allows the delivery of a high radioactive dose to the tumor with minimal toxicity to normal tissues. 90Y has demonstrated to be safe and effective in the management of liver tumors. Authors present a review of the literature available for the use of TheraSphere for radioembolization in the management of liver tumors.

40 CFR 89.126 - Denial, revocation of certificate of conformity.

Science.gov (United States)

2010-07-01

... conformity. 89.126 Section 89.126 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... Standards and Certification Provisions § 89.126 Denial, revocation of certificate of conformity. (a) If... issued certificate of conformity if the Administrator finds any one of the following infractions to be...

A divalent rare earth oxide semiconductor: Yttrium monoxide

Science.gov (United States)

Kaminaga, Kenichi; Sei, Ryosuke; Hayashi, Kouichi; Happo, Naohisa; Tajiri, Hiroo; Oka, Daichi; Fukumura, Tomoteru; Hasegawa, Tetsuya

Rare earth sesquioxides like Y2O3 are known as widegap insulators with the highly stable closed shell trivalent rare earth ions. On the other hand, rare earth monoxides such as YO have been recognized as gaseous phase, and only EuO and YbO were thermodynamically stable solid-phase rock salt monoxides. In this study, solid-phase rock salt yttrium monoxide, YO, was synthesized in a form of epitaxial thin film by pulsed laser deposition method. YO possesses unusual valence of Y2+ ([Kr] 4d1) . In contrast with Y2O3, YO was narrow gap semiconductor with dark-brown color. The electrical conductivity was tunable from 10-1 to 103 Ω-1 cm-1 by introducing oxygen vacancies as electron donor. Weak antilocalization behavior was observed indicating significant spin-orbit coupling owing to 4 d electron carrier. The absorption spectral shape implies the Mott-Hubbard insulator character of YO. Rare earth monoixdes will be new platform of functional oxides. This work was supported by JST-CREST, the Japan Society for the Promotion of Science (JSPS) with Grant-in-Aid for Scientific Research on Innovative Areas (Nos. 26105002 and 26105006), and Nanotechnology Platform (Project No.12024046) of MEXT, Japan.

Obtainment of zirconium oxide and partially stabilized zirconium oxide with yttrium and rare earth oxides, from Brazilian zirconite, for ceramic aim

International Nuclear Information System (INIS)

Ribeiro, S.

1991-05-01

This work presents experimental results for processing of brazilian zirconite in order to obtain zirconium oxide with Yttrium and Rare Earth oxide by mutual coprecipitation for ceramics purposes. Due to analysis of experimental results was possible to obtain the optimum conditions for each one of technological route stage, such as: alkaline fusion; acid leaching; sulfactation and coprecipitation. (author)

In vivo amyloid-β imaging in the APPPS1-21 transgenic mouse model with a 89Zr- labeled monoclonal antibody.

Directory of Open Access Journals (Sweden)

Ann-Marie eWaldron

2016-03-01

Full Text Available Introduction: The accumulation of amyloid-β is a pathological hallmark of Alzheimer’s disease and is a target for molecular imaging probes to aid in diagnosis and disease monitoring. This study evaluated the feasibility of using a radiolabeled monoclonal anti-amyloid-β antibody (JRF/AβN/25 to non-invasively assess amyloid-β burden in aged transgenic mice (APPPS1-21 with μPET imaging.Methods: We investigated the antibody JRF/AβN/25 that binds to full-length Aβ. JRF/AβN/25 was radiolabeled with a [89Zr]-desferal chelate and intravenously injected into 12-13 month aged APPPS1-21 mice and their wild-type (WT controls. Mice underwent in vivo μPET imaging at 2, 4 and 7 days post injection and were sacrificed at the end of each time point to assess brain penetrance, plaque labeling, biodistribution and tracer stability. To confirm imaging specificity we also evaluated brain uptake of a non-amyloid targeting [89Zr]-labeled antibody (Trastuzumab as a negative control, additionally we performed a competitive blocking study with non-radiolabeled Df-Bz-JRF/AβN/25 and finally we assessed the possible confounding effects of blood retention. Results: Voxel-wise analysis of μPET data demonstrated significant [89Zr]-Df-Bz-JRF/AβN/25 retention in APPPS1-21 mice at all time points investigated. With ex vivo measures of radioactivity, significantly higher retention of [89Zr]-Df-Bz-JRF/AβN/25 was found at 4 and 7 day pi in APPPS1-21 mice. Despite the observed genotypic differences, comparisons with immunohistochemistry revealed that in vivo plaque labeling was low. Furthermore, pre-treatment with Df-Bz-JRF/AβN/25 only partially blocked [89Zr]-Df-Bz-JRF/AβN/25 uptake indicative of a high contribution of non-specific binding. Conclusion: Amyloid plaques were detected in vivo with a radiolabeled monoclonal anti-amyloid antibody. The low brain penetrance of the antibodies in addition to non-specific binding prevented an accurate estimation of plaque

A randomized controlled trial of peeling and aspiration of Elschnig pearls and neodymium: yttrium-aluminium-garnet laser capsulotomy.

Science.gov (United States)

Bhargava, Rahul; Kumar, Prachi; Sharma, Shiv Kumar; Kaur, Avinash

2015-01-01

To compare surgical peeling and aspiration and neodymium yttrium garnet laser capsulotomy for pearl form of posterior capsule opacification (PCO). A prospective, randomized, double blind, study was done at Rotary Eye Hospital, Maranda, Palampur, India, Santosh Medical College Hospital, Ghaziabad, India and Laser Eye Clinic, Noida India. Consecutive patients with pearl form of PCO following surgery, phacoemulsification, manual small incision cataract surgery and conventional extracapsular cataract extraction (ECCE) for age related cataract, were randomized to have peeling and aspiration or neodymium yttrium garnet laser capsulotomy. Corrected distance visual acuity (CDVA), intra-operative and post-operative complications were compared. A total of 634 patients participated in the study, and 314 (49.5%) patients were randomized to surgical peeling and aspiration group and 320 (50.5%) to the Nd:YAG laser group. The mean pre-procedural logMAR CDVA in peeling and neodymium: yttrium-aluminium-garnet (Nd:YAG) laser group was 0.80±0.25 and 0.86±0.22, respectively. The mean final CDVA in peeling group (0.22±0.23) was comparable to Nd:YAG group (0.24±0.28; t test, P=0.240). There was a significant improvement in vision after both the procedures (Ppeeling group (262/83.4%) had a CDVA of 0.5 (20/63) or better at 9mo (Ppeeling group (25/7.7% vs 15/4.7%, respectively). On application of ANCOVA, there was less than 0.001% risk that PCO thickness and total laser energy had no effect on rate of complications in Nd:YAG laser group and less than 0.001 % risk that PCO thickness had no effect on complications in peeling group respectively. Sum of square analysis suggests that in the Nd:YAG laser group, thick PCO had a stronger impact on complications (Fischer test probability, Prpeeling group, thick PCO and preoperative vision had a stronger effect on complications than thin PCO, respectively (Fischer test probability, Prpeeling group. Retinal detachment was more common in patients

Yttrium-90 resin microspheres and their use in the treatment of intrahepatic cholangiocarcinoma.

Science.gov (United States)

Filippi, Luca; Schillaci, Orazio; Cianni, Roberto; Bagni, Oreste

2018-04-01

Intrahepatic cholangiocarcinoma (ICC) is a severe and rapidly progressive hepatic tumor. Surgery is often impracticable due to locally advanced presentation. On the other hand, chemotherapy has demonstrated only limited effectiveness. For these reasons, liver-directed therapies have been successfully applied for treating ICC. In particular, radioembolization with Yttrium-90 ( 90 Y)-labeled spheres has been reported to be a promising therapeutic approach for this neoplasia. Two commercial forms of 90 Y-labeled spheres are available: glass (TheraSphere ® ) and resin (SIR-Spheres ® ) microspheres. The aim of the present paper is to review the existing literature on the use of the resin microspheres for the treatment of unresectable and chemorefractory ICC, focusing on the methodology, clinical applications and side effects.

Production, applications and status of zirconium-89 immunoPET agents

International Nuclear Information System (INIS)

Jalilian, A.R.; Osso, Joao Alberto

2017-01-01

Zirconium-89 has attracted huge interests and is used in tracing and quantification of slow biological processes and labeling of long half-live biomolecules such as monoclonal antibodies for pharmacokinetic studies and clinical trials. In this review, a concise introduction to targetry, irradiation data, separation and coordination chemistry of zirconium-89 has been presented. A detailed overreviwew on bi-functional ligands conjugation and "8"9Zr radiolabeling been addressed. The latest status of preclinical as well as clinical trials using "8"9Zr radioimmunomolecules in various human diseases has been presented since 2012. (author)

22 CFR 92.89 - Fees for service of legal process.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Fees for service of legal process. 92.89 Section 92.89 Foreign Relations DEPARTMENT OF STATE LEGAL AND RELATED SERVICES NOTARIAL AND RELATED SERVICES Quasi-Legal Services § 92.89 Fees for service of legal process. No charge should be made for...

Quantitative 89Zr immuno-PET for in vivo scouting of 90Y-labeled monoclonal antibodies in xenograft-bearing nude mice.

NARCIS (Netherlands)

Verel, I.; Visser, G.W.; Boellaard, R.; Boerman, O.C.; Eerd-Vismale, J.E.M. van; Snow, G.B.; Lammertsma, A.A.; Dongen, G.A.M.S. van

2003-01-01

Immuno-PET as a scouting procedure before radioimmunotherapy (RIT) aims at the confirmation of tumor targeting and the accurate estimation of radiation dose delivery to both tumor and normal tissues. Immuno-PET with (89)Zr-labeled monoclonal antibodies (mAbs) and (90)Y-mAb RIT might form such a

Preparation of yttrium hexacyanoferrate/carbon nanotube/Nafion nanocomposite film-modified electrode: Application to the electrocatalytic oxidation of L-cysteine

International Nuclear Information System (INIS)

Qu Lingbo; Yang Suling; Li Gang; Yang Ran; Li Jianjun; Yu Lanlan

2011-01-01

An yttrium hexacyanoferrate nanoparticle/multi-walled carbon nanotube/Nafion (YHCFNP/MWNT/Nafion)-modified glassy carbon electrode (GCE) was constructed. Several techniques, including infrared spectroscopy, energy dispersive spectrometry, scanning electron microscopy and electrochemistry, were performed to characterize the yttrium hexacyanoferrate nanoparticles. The electrochemical behavior of the YHCFNP/MWNT/Nafion-modified GCE in response to L-cysteine oxidation was studied. The response current of L-cysteine oxidation at the YHCFNP/MWNT/Nafion-modified GCE was obviously higher than that at the bare GCE or other modified GCE. The effects of pH, scan rate and interference on the response to L-cysteine oxidation were investigated. In addition, on the basis of these findings, a determination of L-cysteine at the YHCFNP/MWNT/Nafion-modified GCE was carried out. Under the optimum experimental conditions, the electrochemical response to L-cysteine at the YHCFNP/MWNT/Nafion-modified GCE was fast (within 4 s). Linear calibration plots were obtained over the range of 0.20-11.4 μmol L -1 with a low detection limit of 0.16 μmol L -1 . The YHCFNP/MWNT/Nafion-modified GCE exhibited several advantages, such as high stability and good resistance against interference by ascorbic acid and other oxidizable amino acids.

Microstructure of thin film platinum electrodes on yttrium stabilized zirconia prepared by sputter deposition

Energy Technology Data Exchange (ETDEWEB)

Toghan, Arafat, E-mail: arafat.toghan@pci.uni-hannover.de [Institute of Physical Chemistry and Electrochemistry, Leibniz University of Hannover, Callinstrasse 3-3a, D-30167 Hannover (Germany); Khodari, M. [Chemistry Department, Faculty of Science, South Valley University, Qena, 83523 (Egypt); Steinbach, F.; Imbihl, R. [Institute of Physical Chemistry and Electrochemistry, Leibniz University of Hannover, Callinstrasse 3-3a, D-30167 Hannover (Germany)

2011-09-01

(111) oriented thin film Pt electrodes were prepared on single crystals of yttrium-stabilized zirconia (YSZ) by sputter deposition of platinum. The electrodes were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED), X-ray diffraction (XRD), energy-dispersive X-ray analysis (EDX), atomic force microscopy (AFM) and by profilometry. SEM images of the as-sputtered platinum film show a compact amorphous Pt film covering uniformly the substrate. Upon annealing at 1123 K, gaps and pores at the interface develop leading to a partial dewetting of the Pt film. Increasing the annealing temperature to 1373 K transforms the polycrystalline Pt film into single crystalline grains exhibiting a (111) orientation towards the substrate.

{sup 90}Y microspheres prepared by sol-gel method, promising medical material for radioembolization of liver malignancies

Energy Technology Data Exchange (ETDEWEB)

Łada, Wiesława, E-mail: w.lada@ichtj.waw.pl [Institute of Nuclear Chemistry and Technology, 03-195 Warsaw, Dorodna 16 (Poland); Iller, Edward [National Centre for Nuclear Research, Radioisotope Centre POLATOM, 05-400 Otwock, Andrzej Sołtan 7 (Poland); Wawszczak, Danuta [Institute of Nuclear Chemistry and Technology, 03-195 Warsaw, Dorodna 16 (Poland); Konior, Marcin, E-mail: marcin.konior@polatom.pl [National Centre for Nuclear Research, Radioisotope Centre POLATOM, 05-400 Otwock, Andrzej Sołtan 7 (Poland); Dziel, Tomasz [National Centre for Nuclear Research, Radioisotope Centre POLATOM, 05-400 Otwock, Andrzej Sołtan 7 (Poland)

2016-10-01

A new technology for the production of radiopharmaceutical {sup 90}Y microspheres in the form of spherical yttrium oxide grains obtained by sol-gel method has been described. The authors present and discuss the results of investigations performed in the development of new production technology of yttrium microspheres and determination of their physic-chemical properties. The final product has the structure of spherical yttrium oxide grains with a diameter 25–100 μm, is stable and free from contaminants. Irradiation of 20 mg samples of grains with diameter of 20–50 μm in the thermal neutron flux of 1.7 × 10{sup 14} cm{sup −2} s{sup −1} at the core of MARIA research nuclear reactor allowed to obtain microspheres labelled with the {sup 90}Y isotope on the way of the nuclear reaction {sup 89}Y(n, γ){sup 90}Y. Specific activity of irradiated microspheres has been determined by application of absolute triple to double coincidence ratio method (TDCR) and has been evaluated at 190 MBq/mg Y. {sup 90}Y microspheres prepared by the proposed technique can be regarded as a promising medical material for radioembolization of liver malignancies. - Highlights: • Sol-gel methods for preparation of spherical yttrium trioxide grains have been proposed. • Determination condition for irradiation {sup 89}Y{sub 2}O{sub 3} grains in nuclear reactor • Evaluation of specific activity of {sup 90}Y microspheres • Estimation of {sup 90}Y microspheres as promising medical material for radioembolization.

Spin wave propagation in perpendicularly magnetized nm-thick yttrium iron garnet films

Science.gov (United States)

Chen, Jilei; Heimbach, Florian; Liu, Tao; Yu, Haiming; Liu, Chuanpu; Chang, Houchen; Stückler, Tobias; Hu, Junfeng; Zeng, Lang; Zhang, Youguang; Liao, Zhimin; Yu, Dapeng; Zhao, Weisheng; Wu, Mingzhong

2018-03-01

Magnonics offers a new way for information transport that uses spin waves (SWs) and is free of charge currents. Unlike Damon-Eshbach SWs, the magneto-static forward volume SWs offer the reciprocity configuration suitable for SW logic devices with low power consumption. Here, we study forward volume SW propagation in yttrium iron garnet (YIG) thin films with an ultra-low damping constant α = 8 ×10-5 . We design different integrated microwave antenna with different k-vector excitation distributions on YIG thin films. Using a vector network analyzer, we measured SW transmission with the films magnetized in perpendicular orientation. Based on the experimental results, we extract the group velocity as well as the dispersion relation of SWs and directly compare the power efficiency of SW propagation in YIG using coplanar waveguide and micro stripline for SW excitation and detection.

Deposition of yttrium oxysulfide thin films by atomic layer epitaxy

International Nuclear Information System (INIS)

Kukli, K.; University of Tartu, Tartu,; Johansson, L-S.; Nykaenen, E.; Peussa, M.; Ninistoe, L.

1998-01-01

Full text: Yttrium oxysulfide is a highly interesting material for optoelectronic applications. It is industrially exploited in the form of doped powder in catholuminescent phosphors, e.g. Y 2 O 2 S: Eu 3+ for colour TV. Attempts to grow thin films of Y 2 O 2 S have not been frequent and only partially successful due to the difficulties in obtaining crystalline films at a reasonable temperature. Furthermore, sputtering easily leads to a sulphur deficiency. Evaporation of the elements from a multi-source offers a better control of the stoichiometry resulting in hexagonal (0002) oriented films at 580 deg C. In this paper we present the first successful thin film growth experiments using a chemical process with molecular precursors. Atomic layer epitaxy (ALE) allows the use of a relatively low deposition temperature and thus compatibility with other technologies. Already at 425 deg C the reaction between H 2 S and Y(thd) 3 (thd = 2,2,6,6 - tetramethyl-heptane-3,5- dione) yields a crystalline Y 2 O 2 S thin film which was characterized by XRD, XRF and XPS

Co-doping TiO{sub 2} with boron and/or yttrium elements: Effects on antimicrobial activity

Energy Technology Data Exchange (ETDEWEB)

Wang, Yuzheng [School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870 (China); Wu, Yusheng, E-mail: henanwys@sina.com [School of Materials Science and Engineering, Shenyang University of Technology, Shenyang 110870 (China); Yang, He; Xue, Xiangxin; Liu, Zhihua [Institute of Metallurgical Resources and Environmental Engineering, Northeastern University, Shenyang 110819 (China)

2016-09-15

Highlights: • B-Y/TiO{sub 2} nano materials firstly applied to the fields of antibacterial materials. • Systems analysis the existence state of boron and yttrium ion in TiO{sub 2}. • Doping B and Y greatly strengthened the antibacterial activity of TiO{sub 2}. - Abstract: Pure TiO{sub 2}, boron and/or yttrium doped TiO{sub 2} nano-materials were synthesized by a sol–gel method and characterized by XRD, SEM, XPS and PL. XRD analysis indicates that, in the pure TiO{sub 2} and B single doped TiO{sub 2} (B-TiO{sub 2}) nano-materials calcinated at 700 °C, the presence of TiO{sub 2} is a mixture of anatase and rutile; in the Y single doped (Y-TiO{sub 2}), B and Y co-doped TiO{sub 2} nano-materials (B/Y-TiO{sub 2}), the presence of TiO{sub 2} is anatase. SEM image shows the prepared materials have a common round morphology and hexagonal plate morphology caused by the agglomeration of particles. Boron atoms are partially embedded into the TiO{sub 2} interstitial structure or incorporated into the TiO{sub 2} lattice through occupying the position of the oxygen atoms. The results of antimicrobial experiment show that B/Y-TiO{sub 2} material has a remarkable antimicrobial activity. Compared with the visible light irradiation, antimicrobial activity of B/Y-TiO{sub 2} in dark is significant poor.

In situ hydrothermal crystallization of hexagonal hydroxyapatite tubes from yttrium ion-doped hydroxyapatite by the Kirkendall effect.

Science.gov (United States)

Li, Chengfeng; Ge, Xiaolu; Li, Guochang; Lu, Hao; Ding, Rui

2014-12-01

An in situ hydrothermal crystallization method with presence of glutamic acid, urea and yttrium ions was employed to fabricate hexagonal hydroxyapatite (HAp, Ca5(PO4)3(OH)) tubes with length of 200 nm-1 μm. Firstly, yttrium ion-doped HAp (Y-HAp, Ca(5-x)Y(x)(PO4)3(OH)) was synthesized after hydrolysis of urea and HPO4(2-) ions at 100°C with a dwell time of 24h. The shift of X-ray diffraction peaks of HAp to high angle was caused the substitution of Ca(2+) ions by small-sized Y(3+) ions. At 160°C, further hydrolysis reactions of urea and HPO4(2-) ions resulted in the generation of ample OH(-) and PO4(3-) ions, which provided a high chemical potential for the dissolution of Y-HAp and recrystallization of HAp and YPO4. Finally, HAp tubes were formed in situ on Y-HAp according to the Kirkendall effect as a result of the difference of diffusion rate of cations (Ca(2+) ions, outward and slow) and anions (OH(-) and PO4(3-) ions, inward and fast). The formation process of HAp tube was simulated by the encapsulation of fluorescein molecules in precipitates. Photoluminescence properties were enhanced for HAp tubes with thick and dense walls. This novel tubular material could find wide applications as carriers of drugs, dyes and catalysts. Copyright © 2014 Elsevier B.V. All rights reserved.

Spectrum and energy levels of six-times ionized yttrium (Y VII)

Science.gov (United States)

Reader, Joseph

2018-03-01

The spectrum of six-times ionized yttrium, Y VII, was photographed with a sliding-spark discharge on 10.7 m normal- and grazing-incidence spectrographs. The region of observation was 157-824 Å. The observations extend the known configurations 4s24p3, 4s4p4, 4p5, 4s24p25s, 4s24p26s to the nearly complete 4s24p24d configuration. Our results for 4s24p24d significantly revise results of Rahimullah et al (1978 Phys. Scr. 18 96); Ateqad et al (1984 J. Phys. B: At. Mol. Phys. 17 4617). A total of 168 lines and 56 energy levels are now known for this ion. The observed configurations were interpreted with Hartree-Fock calculations and least-squares fits of the energy parameters to the observed levels. Transition probabilities for all classified lines were calculated with the fitted parameters.

Phase I trial of yttrium-90-labeled anti-prostate-specific membrane antigen monoclonal antibody J591 for androgen-independent prostate cancer.

Science.gov (United States)

Milowsky, Matthew I; Nanus, David M; Kostakoglu, Lale; Vallabhajosula, Shankar; Goldsmith, Stanley J; Bander, Neil H

2004-07-01

To determine the maximum-tolerated dose (MTD), toxicity, human antihuman antibody (HAHA) response, pharmacokinetics, organ dosimetry, targeting, and preliminary efficacy of yttrium-90-labeled anti-prostate-specific membrane antigen monoclonal antibody J591 ((90)Y-J591) in patients with androgen-independent prostate cancer (PC). Patients with androgen-independent PC and evidence of disease progression received indium-111-J591 for pharmacokinetic and biodistribution determinations followed 1 week later by (90)Y-J591 at five dose levels: 5, 10, 15, 17.5, and 20 mCi/m(2). Patients were eligible for up to three re-treatments if platelet and neutrophil recovery was satisfactory. Twenty-nine patients with androgen-independent PC received (90)Y-J591, four of whom were re-treated. Dose limiting toxicity (DLT) was seen at 20 mCi/m(2), with two patients experiencing thrombocytopenia with non-life-threatening bleeding episodes requiring platelet transfusions. The 17.5-mCi/m(2) dose level was determined to be the MTD. No re-treated patients experienced DLT. Nonhematologic toxicity was not dose limiting. Targeting of known sites of bone and soft tissue metastases was seen in the majority of patients. No HAHA response was seen. Antitumor activity was seen, with two patients experiencing 85% and 70% declines in prostate-specific antigen (PSA) levels lasting 8 and 8.6 months, respectively, before returning to baseline. Both patients had objective measurable disease responses. An additional six patients (21%) experienced PSA stabilization. The recommended dose for (90)Y-J591 is 17.5 mCi/m(2). Acceptable toxicity, excellent targeting of known sites of PC metastases, and biologic activity in patients with androgen-independent PC warrant further investigation of (90)Y-J591 in the treatment of patients with PC.

Finite temperature magnon spectra in yttrium iron garnet from a mean field approach in a tight-binding model

Science.gov (United States)

Shen, Ka

2018-04-01

We study magnon spectra at finite temperature in yttrium iron garnet using a tight-binding model with nearest-neighbor exchange interaction. The spin reduction due to thermal magnon excitation is taken into account via the mean field approximation to the local spin and is found to be different at two sets of iron atoms. The resulting temperature dependence of the spin wave gap shows good agreement with experiment. We find that only two magnon modes are relevant to the ferromagnetic resonance.

40 CFR 89.902 - Definitions.

Science.gov (United States)

2010-07-01

... piece of equipment employed from year to year in the ordinary course of business for product development, production method assessment, and market promotion purposes. Testing exemption means an exemption which may be granted under § 89.1004(b) for the purpose of research investigations, studies, demonstrations or...

Complexes of (III) lanthanides isothiocyanate and (III) yttrium with 2,6-lutidine-n-oxide (2,6-LNO)

International Nuclear Information System (INIS)

Arico, E.M.

1990-01-01

The preparation and characterization of the complexes of yttrium and some lanthanides isothiocyanate with 2,6-lutidine-N-oxide (2,6-LNO) are described. The ligand employed in the synthesis of the compounds were prepared by the reaction of 2,6-lutidine with hydrogen peroxide in glacial acetic acid. The complexes were prepared using the relation 1:3 salt-ligand. Their characterization was made by elemental analysis, electrolytic conductance measurements, X-ray powder patterns, infrared spectra, electronic absorption spectra of the neodymium and fluorescence spectra of the europium compounds. (author)

Magnetic field effect on sublattice contributions into the Faraday effect in Y3Fe5o12 yttrium ferrite-garnet

International Nuclear Information System (INIS)

Ivashintsova, V.L.; Pisarev, R.V.

1980-01-01

Field dependencies of the Faraday effect in yttrium ferrite-garnet in the 80-600 K temperature range on the 1.15 μm wavelength are studied. It is shown that the changes observed in the Faraday effect under the influence of the external field can be explained by magnetic susceptibility of the tetrahedric and octahedric sublattices, and also by the field effect on the specific sublattice contributions into the Faraday effect

Antibody-guided three-step therapy for high grade glioma with yttrium-90 biotin

International Nuclear Information System (INIS)

Paganelli, G.; Grana, C.; Chinol, M.; Cremonesi, M.; De Cicco, C.; Zoboli, S.; De Braud, F.; Robertson, C.; Zurrida, S.; Veronesi, U.; Casadio, C.; Siccardi, A.G.

1999-01-01

While the incidence of brain tumours seems to be increasing, median survival in patients with glioblastoma remains less than 1 year, despite improved diagnostic imaging and neurosurgical techniques, and innovations in treatment. We have developed an avidin-biotin pre-targeting approach for delivering therapeutic radionuclides to gliomas, using anti-tenascin monoclonal antibodies, which seems potentially effective for treating these tumours. We treated 48 eligible patients with histologically confirmed grade III or IV glioma and documented residual disease or recurrence after conventional treatment. Three-step radionuclide therapy was performed by intravenous administration of 35 mg/m 2 of biotinylated anti-tenascin monoclonal antibody (1st step), followed 36 h later by 30 mg of avidin and 50 mg of streptavidin (2nd step), and 18-24 h later by 1-2 mg of yttrium-90-labelled biotin (3rd step). 90 Y doses of 2.22-2.96 GBq/m 2 were administered; maximum tolerated dose (MTD) was determined at 2.96 GBq/m 2 . Tumour mass reduction (>25%-100%), documented by computed tomography or magnetic resonance imaging, occurred in 12/48 patients (25%), with 8/48 having a duration of response of at least 12 months. At present, 12 patients are still in remission, comprising four with a complete response, two with a parital response, two with a minor response and four with stable disease. Median survival from 90 Y treatment is 11 months for grade IV glioblastoma and 19 months for grade III anaplastic gliomas. Avidin-biotin based three-step radionuclide therapy is well tolerated at the dose of 2.2 GBq/m 2 , allowing the injection of 90 Y-biotin without bone marrow transplantation. This new approach interferes with the progression of high-grade glioma and may produce tumour regression in patients no longer responsive to other therapies. (orig.)

7 CFR 983.89 - Termination.

Science.gov (United States)

2010-01-01

..., ARIZONA, AND NEW MEXICO Miscellaneous Provisions § 983.89 Termination. (a) The Secretary may at any time..., That such majority has, during such representative period, produced for market more than fifty percent of the volume of such pistachios produced for market, but such termination shall be announced at...

The study of structural characteristic of yttrium(3+) aquaion by density functional methods

International Nuclear Information System (INIS)

Buz'ko, V.Yu.; Sukhno, I.V.; Polushin, A.A.; Panyushkin, V.T.

2006-01-01

Structural characteristics of the yttrium aquaion Y(H 2 O) 8 3+ are calculated by DFT technique using density functionals SVWN5, B3LYP, B3P86, O3LYP, B3PW91, B1LYP, B971, MPW1PW9, PBE1PBE, BHandH and BNandHLYP. All calculations are carried out by means of GAUSSIAN-03 code. Structural characteristics of the Y(H 2 O) 8 3+ aquaion obtained by the use of the density functional method agree satisfactorily with the experiment. Hybrid nonlocal GGA-functionals foretell worse the structural characteristics of the Y(H 2 O) 8 3+ aquaion as compared with the reasonable simple combined functional BHandH and the simplest functional SVWN5 of the LSDA theory [ru

40 CFR 81.89 - Metropolitan Cheyenne Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.89 Section 81.89 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.89 Metropolitan Cheyenne Intrastate Air Quality Control Region. The Metropolitan Cheyenne Intrastate Air Quality Control Region (Wyoming) consists of the territorial area...

40 CFR 8.9 - Measures to assess and verify environmental impacts.

Science.gov (United States)

2010-07-01

... environmental impacts. 8.9 Section 8.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY GENERAL ENVIRONMENTAL IMPACT ASSESSMENT OF NONGOVERNMENTAL ACTIVITIES IN ANTARCTICA § 8.9 Measures to assess and verify environmental impacts. (a) The operator shall conduct appropriate monitoring of key environmental indicators as...

Light-ion spectroscopy with exotic targets

International Nuclear Information System (INIS)

Struble, G.L.; Lanier, R.G.

1992-01-01

Understanding the rich and diverse aspects underlying the physics of nuclear structure requires a variety of experimental techniques. In our laboratory, we have concentrated on experimental techniques using light-ion probes and isotopes that are technically difficult to fabricate into targets. In particular, our studies of p-, d-, and t-induced nuclear reactions on the radioactive targets of 152,154 Eu and 148 Gd have illuminated some very specific and very interesting features of nuclear structure near the N = 89 shape-transition region

Determination of the fission products yields, lanthanide and yttrium, in the fission of 238U with neutrons of fission spectra

International Nuclear Information System (INIS)

Nicoli, I.G.

1981-06-01

A radiochemical investigation is performed to measure the cumulative fission product yields of several lantanides and yttrium nuclides in the 238 U by fission neutron spectra. Natural and depleted uranium are irradiated under the same experimental conditions in order to find a way to subtract the contribution of the 235 U fission. 235 U percentage in the natural uranium was 3.5 times higher than in the depleted uranium. Uranium oxides samples are irradiated inside the core of the Argonaut Reactor, at the Instituto de Engenharia Nuclear, and the lantanides and yttrium are chemically separated. The fission products gamma activities were detected, counted and analysed in a system constituted by a high resolution Ge(Li) detector, 4096 multichannel analyser and a PDP-11 computer. Cumulative yields for fission products with half-lives between 1 to 33 hours are measured: 93 Y, 141 La, 142 La, 143 Ce and 149 Nd. The chain total yields are calculated. The cumulative fission yields measured for 93 Y, 141 La, 142 La, 143 Ce and 149 Nd are 4,49%, 4,54%, 4,95%, 4,16% and 1,37% respectively and they are in good agreement with the values found in the literature. (Author) [pt

External temperature and pressure effects on thermodynamic properties and mechanical stability of yttrium chalcogenides YX (X=S, Se and Te)

Energy Technology Data Exchange (ETDEWEB)

Seddik, T. [Laboratoire de Physique Quantique et de Modélisation Mathématique, Université de Mascara, 29000 Mascara (Algeria); Khenata, R., E-mail: khenata_rabah@yahoo.fr [Laboratoire de Physique Quantique et de Modélisation Mathématique, Université de Mascara, 29000 Mascara (Algeria); Bouhemadou, A.; Guechi, N. [Laboratory for Developing New Materials and their Characterization, Department of Physics, Faculty of Science, University of Setif, 19000 Setif (Algeria); Sayede, A. [Université Lille Nord de France, F-59000 Lille (France); Université-Artois, UCCS, F-62300 Lens (France); CNRS, UMR 8181, F-59650 Villeneuve d’Ascq (France); Varshney, D. [Materials Science Laboratory, School of Physics, Vigyan Bhavan, Devi Ahilya University, Khandwa Road Campus, Indore 452001, Madhya Pradesh (India); Al-Douri, Y. [Institute of Nono Electronic Engineering, University Malaysia Perlis, 01000 Kangar, Perlis (Malaysia); Reshak, A.H. [Institute of Complex Systems, FFPW, CENAKVA, University of South Bohemia in CB, Nove Hrady 37333 (Czech Republic); Center of Excellence Geopolymer and Green Technology, School of Material Engineering, University Malaysia Perlis, 01007 Kangar, Perlis (Malaysia); Bin-Omran, S. [Department of Physics and Astronomy, Faculty of Science, King Saud University, PO Box 2455, Riyadh 11451 (Saudi Arabia)

2013-11-01

The full potential linearized augmented plane wave method within the framework of density functional theory is employed to investigate the structural, thermodynamic and elastic properties of the yttrium chalcogenides (YX: X=S, Se, and Te) in their low-pressure phase (Fm3{sup ¯}m) and high-pressure phase (Pm3{sup ¯}m). The exchange-correlation potential is treated with the generalized gradient approximation of Perdew–Burke–Ernzerhof (GGA-PBE). Temperature dependence of the volume and both adiabatic and isothermal bulk moduli is predicted for a temperature range from 0to1200K for the both phases of the herein considered materials. Furthermore, we have analyzed the thermodynamic properties such as the heat capacities, C{sub V} and C{sub P}, thermal expansion, α, and Debye temperature, Θ{sub D,} under variable pressure and temperature. We have calculated the isothermal elastic constants C{sub ij}{sup T} of the YX monochalcogenides in both NaCl-B1 and CsCl-B2 phases at zero pressure and a temperature range 0−1200K. The results show that rare earth yttrium monochalcogenides are mechanically stable at high temperature. The elastic anisotropy of all studied materials in the two phases has been studied using three different methods.

40 CFR 89.507 - Sample selection.

Science.gov (United States)

2010-07-01

... Auditing § 89.507 Sample selection. (a) Engines comprising a test sample will be selected at the location...). However, once the manufacturer ships any test engine, it relinquishes the prerogative to conduct retests...

The dynamics of accumulation and disappearance of {sup 89}Sr in tea

Energy Technology Data Exchange (ETDEWEB)

Chuanqun, Chen; Shouxiang, Wang; Yongxi, Zhang; Zhiming, Sun [Zhejiang Agricultural Univ., Hangzhou (China). Inst. of Nuclear Agricultural Sciences

1994-06-01

The {sup 89}Sr was put into a tea tree-soil system by different ways. The results showed that for {sup 89}Sr put into the system through the above-ground 1 part of tea tree, its concentration in tea was much higher than that through soil. The concentration of {sup 89}Sr in older tea was higher than that in shoot for the same treatment. The accumulation and disappearance of {sup 89}Sr in tea varied with the treatments. For the treatment through the above-ground part, the concentrations of {sup 89}Sr in older tea and shoot were monotonously decreasing with time. For the treatment through soil the concentration of {sup 89}Sr in shoot increased initially to a maximum value, then decreased slowly; while the concentration of {sup 89}Sr in older tea increased quickly in a definite period, then increased slowly to gain a saturated value. In addition, the values of concentration factor of {sup 89}Sr in the older tea and shoot were determined, too.

Yttrium and lanthanide nitrate complexes of N,N1-bis(4-antipyryl methylidene) ethylenediamine

International Nuclear Information System (INIS)

Joseph, Siby; Radhakrishnan, P.K.

1998-01-01

Complexes of yttrium and lanthanide nitrates with a Schiff base, N, N 1 -bis(4-antipyrylmethylidene)ethylenediamine (BAME) having the general formula [Ln(BAME) 2 (NO 3 )](NO 3 ) 2 , where Ln = Y, La, Pr, Nd, Sm, Eu, Gd, Dy, Ho and Er have been synthesised and characterised by elemental analyses, molar conductance in non-aqueous solvents, electronic, infrared and proton NMR spectra. BAME acts as a neutral bidentate ligand coordinating through both azomethine nitrogen atoms. One of the nitrate groups is coordinated in a bidentate manner. A coordination number of six may be assigned to the metal ion in these complexes. The covalency parameters evaluated from the solid state electronic spectra suggest weak covalent character of the metal-ligand bond. (author)

A study of strain in thin epitaxial films of yttrium silicide on Si(111)

Science.gov (United States)

Siegal, Michelle F.; Martínez-Miranda, L. J.; Santiago-Avilés, J. J.; Graham, W. R.; Siegal, M. P.

1994-02-01

We present the results of an x-ray diffraction analysis of epitaxial yttrium silicide films grown on Si(111), with thicknesses ranging from 14 to 100 Å. The macroscopic strain along the out-of-plane direction for films containing pits or pinholes follows the trend observed previously in films of thicknesses up to 510 Å. The out-of-plane lattice parameter decreases linearly with film thickness. We show preliminary evidence that pinhole-free films do not follow the above trend, and that strain in these films has the opposite sign than in films with pinholes. Finally, our results also indicate that the mode of growth, coupled to the interfacial thermal properties of the films, affects the observed value for the strain in the films.

A study of strain in thin epitaxial films of yttrium silicide on Si(111)

International Nuclear Information System (INIS)

Siegal, M.F.; Martinez-Miranda, L.J.; Santiago-Aviles, J.J.; Graham, W.R.; Siegal, M.P.

1994-01-01

We present the results of an x-ray diffraction analysis of epitaxial yttrium silicide films grown on Si(111), with thicknesses ranging from 14 to 100 A. The macroscopic strain along the out-of-plane direction for films containing pits or pinholes follows the trend observed previously in films of thicknesses up to 510 A. The out-of-plane lattice parameter decreases linearly with film thickness. We show preliminary evidence that pinhole-free films do not follow the above trend, and that strain in these films has the opposite sign than in films with pinholes. Finally, our results also indicate that the mode of growth, coupled to the interfacial thermal properties of the films, affects the observed value for the strain in the films

Structure and luminescence spectra of lutetium and yttrium borates synthesized from ammonium nitrate melt

International Nuclear Information System (INIS)

Klassen, Nikolay V.; Shmurak, Semion Z.; Shmyt'ko, Ivan M.; Strukova, Galina K.; Derenzo, Stephen E.; Weber, Marvin J.

2005-01-01

Lutetium and yttrium borates doped with europium, terbium, gadolinium, etc. have been synthesized by dissolving initial oxides and nitrates in ammonium nitrate melt and thermal decomposition of the solvent. Annealings in the range of 500-1100 deg. C modified the dimensions of the grains from 2 to 3 nm to more than 100 nm. Significant dependence of the structure of lutetium borate on slight doping with rare earth ions has been found: terbium makes high-temperature vaterite phase preferential at room temperature, whereas europium stabilizes low-temperature calcite phase. Influence of the structure of the borates on the pattern of the luminescence spectra of europium dopant was observed. Possibilities for manufacturing of scintillating lutetium borate ceramics by means of this method of synthesis are discussed

Structure and luminescence spectra of lutetium and yttrium borates synthesized from ammonium nitrate melt

Science.gov (United States)

Klassen, Nikolay V.; Shmurak, Semion Z.; Shmyt'ko, Ivan M.; Strukova, Galina K.; Derenzo, Stephen E.; Weber, Marvin J.

2005-01-01

Lutetium and yttrium borates doped with europium, terbium, gadolinium, etc. have been synthesized by dissolving initial oxides and nitrates in ammonium nitrate melt and thermal decomposition of the solvent. Annealings in the range of 500-1100°C modified the dimensions of the grains from 2 to 3 nm to more than 100 nm. Significant dependence of the structure of lutetium borate on slight doping with rare earth ions has been found: terbium makes high-temperature vaterite phase preferential at room temperature, whereas europium stabilizes low-temperature calcite phase. Influence of the structure of the borates on the pattern of the luminescence spectra of europium dopant was observed. Possibilities for manufacturing of scintillating lutetium borate ceramics by means of this method of synthesis are discussed.

27 CFR 479.89 - Transfers to the United States.

Science.gov (United States)

2010-04-01

... Transfers to the United States. A firearm may be transferred to the United States or any department... 27 Alcohol, Tobacco Products and Firearms 3 2010-04-01 2010-04-01 false Transfers to the United States. 479.89 Section 479.89 Alcohol, Tobacco Products, and Firearms BUREAU OF ALCOHOL, TOBACCO...

High density Gd-substituted yttrium iron garnets by coprecipitation

International Nuclear Information System (INIS)

Lamastra, Francesca Romana; Bianco, Alessandra; Leonardi, Federica; Montesperelli, Giampiero; Nanni, Francesca; Gusmano, Gualtiero

2008-01-01

Gadolinium-substituted yttrium iron garnets are ferrite materials of primary importance in microwave engineering. Stoichiometric powders of nominal composition Y 2.6 Gd 0.4 Fe 5 O 12 (i.e. Fe/(Y + Gd) = 1.67) were prepared by reverse strike coprecipitation of metal nitrates. In order to investigate the influence of composition on phase formation, non-stoichiometric powders were also synthesised. On the basis of DTA/TGA analysis, dried coprecipitates were calcined between 600 deg. C and 1200 deg. C and then characterised by ICP, XRD and HT-XRD. Amorphous coprecipitates crystallise around 700 deg. C in cubic garnet phase along with small amounts of YFeO 3 and/or α-Fe 2 O 3 . Only iron-rich garnets, either pure or Gd-substituted, calcined at 1200 deg. C or above display a single-phase cubic garnet. According to thermal dilatometry results, calcined powders were sintered in air up to 1470 deg. C. The microstructure of sintered ceramics is made up of fine grains, the average size ranging between 3 μm and 13 μm. Density of sintered bodies ranged from 88% to 98%. Ferromagnetic resonance linewidth (ΔH -3dB ) ranged between 4352.9 A m -1 and 4392.7 A m -1 , depending on composition and microstructure

Sources and distribution of yttrium and rare earth elements in surface sediments from Tagus estuary, Portugal.

Science.gov (United States)

Brito, Pedro; Prego, Ricardo; Mil-Homens, Mário; Caçador, Isabel; Caetano, Miguel

2018-04-15

The distribution and sources of yttrium and rare-earth elements (YREE) in surface sediments were studied on 78 samples collected in the Tagus estuary (SW Portugal, SW Europe). Yttrium and total REE contents ranged from 2.4 to 32mg·kg -1 and 18 to 210mg·kg -1 , respectively, and exhibited significant correlations with sediment grain-size, Al, Fe, Mg and Mn, suggesting a preferential association to fine-grained material (e.g. aluminosilicates but also Al hydroxides and Fe oxyhydroxides). The PAAS (Post-Archean Australian Shale) normalized patterns display three distinct YREE fractionation pattern groups along the Tagus estuary: a first group, characterized by medium to coarse-grained material, a depleted and almost flat PAAS-normalized pattern, with a positive anomaly of Eu, representing one of the lithogenic components; a second group, characterized mainly by fine-grained sediment, with higher shale-normalized ratios and an enrichment of LREE relative to HREE, associated with waste water treatment plant (WWTP) outfalls, located in the northern margin; and, a third group, of fine-grained material, marked by a significant enrichment of Y, a depletion of Ce and an enrichment of HREE over LREE, located near an inactive chemical-industrial complex (e.g. pyrite roast plant, chemical and phosphorous fertilizer industries), in the southern margin. The data allow the quantification of the YREE contents and its spatial distribution in the surface sediments of the Tagus estuary, identifying the main potential sources and confirming the use of rare earth elements as tracers of anthropogenic activities in highly hydrodynamic estuaries. Copyright © 2017 Elsevier B.V. All rights reserved.

14 CFR 135.89 - Pilot requirements: Use of oxygen.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Pilot requirements: Use of oxygen. 135.89... Operations § 135.89 Pilot requirements: Use of oxygen. (a) Unpressurized aircraft. Each pilot of an... operated with the cabin pressure altitude more than 10,000 feet MSL, each pilot shall comply with paragraph...

High-Pressure Synthesis and Characterization of the Ammonium Yttrium Borate (NH4)YB8O14.

Science.gov (United States)

Schmitt, Martin K; Podewitz, Maren; Liedl, Klaus R; Huppertz, Hubert

2017-11-20

The first high-pressure yttrium borate (NH 4 )YB 8 O 14 was synthesized at 12.8 GPa/1300 °C using a Walker-type multianvil module. The compound crystallizes in the orthorhombic space group Pnma (no. 62) with the lattice parameters a = 17.6375(9), b = 10.7160(5), and c = 4.2191(2) Å. (NH 4 )YB 8 O 14 constitutes a novel structure type but exhibits similarities to the crystal structure of β-BaB 4 O 7 . X-ray single-crystal and powder diffraction, EDX, vibrational spectroscopy as well as quantum chemical calculations were used to characterize (NH 4 )YB 8 O 14 .

Determination of rare-earth elements, yttrium and scandium in manganese nodules by inductively-coupled argon-plastma emission spectrometry

Science.gov (United States)

Fries, T.; Lamothe, P.J.; Pesek, J.J.

1984-01-01

A sequential-scanning, inductively-coupled argon plasma emission spectrometer is used for the determination of the rare-earth elements, plus yttrium and scandium, in manganese nodules. Wavelength selection is optimized to minimize spectral interferences from manganese nodule components. Samples are decomposed with mixed acids in a sealed polycarbonate vessel, and elements are quantified without further treatment. Results for U.S. Geological Survey manganese nodule standards A-1 and P-1 had average relative standard deviations of 6.8% and 8.1%, respectively, and results were in good agreement with those obtained by other methods. ?? 1984.

Optimization of 90Sr/89Sr measurements

Directory of Open Access Journals (Sweden)

Legarda F.

2012-04-01

Full Text Available One of the key points in the double measurement method for the measurement of both, 89Sr and 90Sr, by using a proportional counter is the choice of the times at which the measurements should be done. In this paper, the formulae to calculate the 89Sr and 90Sr detection limits in conditions of radioactive equilibrium between 90Y and 90Sr are derived, and an analysis of them as a function of the time between the two measurements is done. The choice for the time of the second measurement is going to depend on the desired quality of the results to be obtained.

TOKSISITAS PROTEIN 89 kDa PRODUK EKSTRASELULER Streptococcus agalactiae PADA IKAN NILA (Oreochromis niloticus

Directory of Open Access Journals (Sweden)

Amrullah Amrullah

2015-09-01

Full Text Available Identifikasi protein toksin yang bersifat antigenik dari produk ekstraselular (ECP crude Streptococcus agalactiae penting dilakukan untuk pengembangan vaksin protein toksoid. Penelitian ini bertujuan untuk mengevaluasi toksisitas protein dengan berat molekul 89 kDa dari ECP Streptococcus agalactiae hasil fraksinasi dengan SDS-PAGE (ECPP89. Ikan nila dengan bobot sekitar 25 g masing-masing diinjeksi secara intraperitonial dengan protein ECPP89 dosis 1, 2, 4, 8, dan 16 μg/mL/ekor ikan (secara berturut-turut diberi kode ECPP89-1, ECPP89-2, ECPP89-4, ECPP89-8, dan ECPP89-16. Sebagai kontrol positif ikan diinjeksi dengan bakteri utuh S. agalactiae 1 x 104 cfu/mL (WCB dan ECP crude S. agalactiae (ECPC, sementara kontrol negatif ikan diinjeksi larutan PBS. Ikan dipelihara selama 15 hari dengan kepadatan 10 ekor (70 L air. Hasil penelitian menunjukkan bahwa ikan nila yang diinjeksi dengan ECPP89 mengalami gejala seperti perubahan morfologi, perubahan nafsu makan, dan perubahan renang ikan. Mortalitas pada perlakuan ECPP89 secara umum lebih tinggi dibandingkan dengan ECPC, namun lebih rendah (p<0,05 dibandingkan dengan WCB. Mortalitas ikan pada perlakuan ECPP89-4, ECPP89-8, dan ECPP89-16 tidak berbeda tetapi secara signifikan lebih tinggi dibandingkan dengan ECPC dan dua dosis perlakuan ECPP89 lainnya (p<0,05. Ikan kontrol negatif tidak mengalami kematian maupun perubahan klinis. Hasil ini menunjukkan bahwa ECPP89 merupakan protein toksin dari ECP S. agalactiae.

Effect of yttrium doping on the dielectric properties of CaCu{sub 3}Ti{sub 4}O{sub 12} thin film produced by chemical solution deposition

Energy Technology Data Exchange (ETDEWEB)

Saji, Viswanathan S., E-mail: vssaji@chosun.ac.k [Chosun University, College of Dentistry and 2nd Stage of Brain Korea 21 for College of Dentistry, Gwangju-501-759 (Korea, Republic of); Choe, Han Cheol [Chosun University, College of Dentistry and 2nd Stage of Brain Korea 21 for College of Dentistry, Gwangju-501-759 (Korea, Republic of)

2009-05-29

Pure and yttrium substituted CaCu{sub 3}Ti{sub 4-x}Y{sub x}O{sub 12-x/} {sub 2} (x = 0, 0.02, 0.1) thin films were prepared on boron doped silica substrate employing chemical solution deposition, spin coating and rapid thermal annealing. The phase and microstructure of the sintered films were examined using X-ray diffraction and scanning electron microscopy. Dielectric properties of the films were measured at room temperature using electrochemical impedance spectroscopy. Highly ordered polycrystalline CCTO thin film with bimodal grain size distribution was achieved at a sintering temperature of 800 {sup o}C. Yttrium doping was found to have beneficial effects on the dielectric properties of CCTO thin film. Dielectric parameters obtained for a CaCu{sub 3}Ti{sub 4-x}Y{sub x}O{sub 12-x} {sub /2} (x = 0.02) film at 1 KHz were k {approx} 2700 and tan {delta} {approx} 0.07.

Feature-based RNN target recognition

Science.gov (United States)

Bakircioglu, Hakan; Gelenbe, Erol

1998-09-01

Detection and recognition of target signatures in sensory data obtained by synthetic aperture radar (SAR), forward- looking infrared, or laser radar, have received considerable attention in the literature. In this paper, we propose a feature based target classification methodology to detect and classify targets in cluttered SAR images, that makes use of selective signature data from sensory data, together with a neural network technique which uses a set of trained networks based on the Random Neural Network (RNN) model (Gelenbe 89, 90, 91, 93) which is trained to act as a matched filter. We propose and investigate radial features of target shapes that are invariant to rotation, translation, and scale, to characterize target and clutter signatures. These features are then used to train a set of learning RNNs which can be used to detect targets within clutter with high accuracy, and to classify the targets or man-made objects from natural clutter. Experimental data from SAR imagery is used to illustrate and validate the proposed method, and to calculate Receiver Operating Characteristics which illustrate the performance of the proposed algorithm.

The liquid membrane for extraction of Yttrium and Dysprosium from Acid Nitric

International Nuclear Information System (INIS)

Johny, W.S.; Raldi-Artono-Koestoer; Kris-Tri-Basuki; Sudibyo

1996-01-01

The determination of surfactant in liquid membrane has been done. The surfactant is span-80 (sorbitol-monooleate), the liquid membrane phase was the organic phase (O), the internal liquid phase (W) with ratio O/W = 1, and surfactant. The organic phase using D 2 EHPA in the kerosene and the internal liquid phase using aqua des or acid nitric. The determination of surfactant with variation of span-80 (0,25 - 2%) in the liquid membrane volume. The speed of stirrer was 3500 rpm in 20 minute. The ratio of liquid membrane phase form and external phase (aqua des or acid nitric) was 1, the speed of stirrer was 350 rpm in 10 minute (permeation process). The liquid phase and the liquid membrane phase was separated and then determinated the volume of liquid membrane, the result of percentage of span-80 was 0,25 % volume. The extraction of yttrium and dysprosium in 2 M HNO 3 was Kd y = 2.945 and Kd D y = 0.019

Dynamics of laser-induced magnetization in Ce-doped yttrium aluminum garnet

International Nuclear Information System (INIS)

Kolesov, Roman

2007-01-01

Circularly polarized short laser pulse induces nonequilibrium population of spin levels in the excited state of Ce 3+ -ion embedded in yttrium aluminium garnet crystal and, consequently, the magnetization of the crystal associated with spin polarization. Dynamic behavior of laser-induced magnetization is studied as a function of the external magnetic field. It reveals spin oscillations attributed to the effect of hyperfine magnetic field produced by 27 Al nuclei on the Ce 3+ spin. A simple theoretical model explaining spin oscillations is presented. It shows that circularly polarized light induces spin coherence at the transition between Zeeman sublevels of Ce 3+ ion in the lowest 5d state. Temporal shape of laser-induced magnetization signal reveals the following parameters of this state: (1) the spin-lattice relaxation constant is ≅2x10 7 s -1 , (2) inhomogeneous spin dephasing time is ≅4 ns, and (3) the g tensor of the state seems to be isotropic with the g factor being in the range 0.7-0.9. In addition, the width of the local hyperfine field distribution is ≅40 G

Polarized neutron diffraction - a tool for testing extinction models: application to yttrium iron garnet

International Nuclear Information System (INIS)

Bonnet, M.; Delapalme, A.; Becker, P.

1976-01-01

This paper shows that polarized neutron experiments, which do not depend on any scale factor, are very dependent on extinction and provide original tests for extinction models. Moon, Koehler, Cable and Child (1972) have formulated the problem and proposed a first-order solution applicable only when the extinction is small. In the first part, some analytical derivations of secondary extinction corrections are discussed, using the formalism of Becker and Coppens (1974). In the second part, the main principles governing polarized neutron diffraction are briefly reviewed, with a special discussion of extinction problems. The method is then applied to the case of yttrium iron garnet (YIG). This experiment shows the technique of polarized neutrons to be very powerful for testing extinction models and for deciding whether the crystal behaves dynamically or kinematically (following Kato's criterion). (Auth.)

Complexes between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand

International Nuclear Information System (INIS)

Silva, M.A.A. da.

1991-01-01

The preparation and characterization of addition compounds between lanthanide (III) and yttrium (III) picrates and tetra methylene sulfoxide as ligand were described. The adducts were prepared in the molar relation 1 (salt): 3(ligand) in ethanol. They are microcrystalline with more intense color than those of their respective hydrated salts. At room temperature conditions they are non hygroscopic and do not present perceptible alterations. They became slightly opalescent, when heated between 363 and 423 K. At higher temperatures under several heating ratios, the behavior shown is the same: melting between 439 and 472 K. The characterization of the compounds was made by elemental analysis, electrolytic conductance measurements, X-ray powder patterns, infrared spectroscopy, visible electronic absorption and emission spectra of the neodymium (III) and europium (III), respectively. (author). 116 refs., 17 tabs., 11 figs

Electrothermal vaporization inductively coupled plasma mass spectrometry for the determination of trace amount of lanthanides and yttrium in soil with polytetrafluroethylene emulsion as a chemical modifier

International Nuclear Information System (INIS)

He Man; Hu, Bin; Jiang Zucheng

2005-01-01

A method of electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the determination of trace lanthanides and yttrium in soil samples with a polytetrafluorethylene (PTFE) emulsion as chemical modifier to promote the vaporization of the analytes from the graphite furnace was developed in this paper. The analytical characteristics, spectral interference and matrix effect of the analytical method were evaluated and critically compared with those of pneumatic nebulization inductively coupled plasma mass spectrometry (PN-ICP-MS). Under the optimized operation conditions, the relative detection limits of lanthanides (La-Lu) and yttrium for ETV-ICP-MS and PN-ICP-MS were 0.4-20 ng l -1 and 1.0-21 ng l -1 , respectively, the absolute detection limits for ETV-ICP-MS were 4-200 fg, which were improved by 1-2 orders of magnitude compared with PN-ICP-MS. While the analytical precision of ETV-ICP-MS is worse than that of PN-ICP-MS, with the R.S.D.s (%) of 4.1-10% for the former and 2.9-7.8% for the latter. Regarding to the matrix effect, both conventional method and stepwise dilution method were employed to observe the effect of matrix and the very similar results were obtained. It was found that the highest tolerance concentration of the matrix is 1000 mg l -1 and 800 mg l -1 for ETV-ICP-MS and PN-ICP-MS, respectively. To assess the accuracy, the proposed method was applied to the determination of trace lanthanides and yttrium in three different soil standard reference materials and one soil sample, and the determined values are in good agreement with the certified values or reference values

Fully microscopic DWBA analyses on 89Y (α, p)92Zr reaction

International Nuclear Information System (INIS)

Yuan Jian; Mao Zhiqiang; Zhang Peihua

1988-01-01

The differential cross sections have been measured for the 89 Y (α, p) 92 Zr reaction with some low-lying states and the 89 Y (α, α) 8( Y elastic scattering by using 26.1 MeV α beam. A fully microscopic DWBA analyses for 89 Y (α, α) 92 Zr have been performed by using 89 Y and 92 Zr shell-model wavefunction with or without the core excited configuration. With the core excited configuration, relative strengths of the ground state and the first excited state are greatly improved. Finally, the absolute cross sections for 89 (α, p) 92 Zr and importance of shallow well depth of α potential are discussed

Quantitative assessment of Zirconium-89 labeled cetuximab using PET/CT imaging in patients with advanced head and neck cancer: a theragnostic approach.

Science.gov (United States)

Even, Aniek J G; Hamming-Vrieze, Olga; van Elmpt, Wouter; Winnepenninckx, Véronique J L; Heukelom, Jolien; Tesselaar, Margot E T; Vogel, Wouter V; Hoeben, Ann; Zegers, Catharina M L; Vugts, Daniëlle J; van Dongen, Guus A M S; Bartelink, Harry; Mottaghy, Felix M; Hoebers, Frank; Lambin, Philippe

2017-01-17

Biomarkers predicting treatment response to the monoclonal antibody cetuximab in locally advanced head and neck squamous cell carcinomas (LAHNSCC) are lacking. We hypothesize that tumor accessibility is an important factor in treatment success of the EGFR targeting drug. We quantified uptake of cetuximab labeled with Zirconium-89 (89Zr) using PET/CT imaging.Seventeen patients with stage III-IV LAHNSCC received a loading dose unlabeled cetuximab, followed by 10 mg 54.5±9.6 MBq 89Zr-cetuximab. PET/CT images were acquired either 3 and 6 or 4 and 7 days post-injection. 89Zr-cetuximab uptake was quantified using standardized uptake value (SUV) and tumor-to-background ratio (TBR), and correlated to EGFR immunohistochemistry. TBR was compared between scan days to determine optimal timing.Uptake of 89Zr-cetuximab varied between patients (day 6-7: SUVpeak range 2.5-6.2). TBR increased significantly (49±28%, p < 0.01) between first (1.1±0.3) and second scan (1.7±0.6). Between groups with a low and high EGFR expression a significant difference in SUVmean (2.1 versus 3.0) and SUVpeak (3.2 versus 4.7) was found, however, not in TBR. Data is available at www.cancerdata.org (DOI: 10.17195/candat.2016.11.1).In conclusion, 89Zr-cetuximab PET imaging shows large inter-patient variety in LAHNSCC and provides additional information over FDG-PET and EGFR expression. Validation of the predictive value is recommended with scans acquired 6-7 days post-injection.

Determination of rare earth element content in yttrium aluminium garnet crystals by absorption spectrophotometry method

International Nuclear Information System (INIS)

Mejl'man, M.L.; Kolomijtsev, A.I.; Baskakova, Z.M.; Bagdasarov, Kh.S.; Kevorkov, A.M.

1985-01-01

Possibility of determination of relative and absolute contents of impurity trivalent REE ions in yttrium aluminium garnet of (YAG) monocrystals has been studied by the absorption spectrophotometry method. Absorption spectra in UV and visible regions YAG monocrystals doped by REE are studied. For each admixture the characteristic lines or absorption bands not overlapping with lines of other admixtures are defined and investigated. The extinction coefficients of characteristic lines are determined which allow one to measure absolute REE admixture concentrations in garnet crystals. A conclusion is drawn that the absorption spectrophotometry method permits to measure REE admixture content in YAG monocrystals within the concentration range of approximately 1x10sup(-3)-5 mas. % with an accuracy not less than 20% (with sample thickness of approximately 1 cm)

Correlation between evolution of inclusions and pitting corrosion in 304 stainless steel with yttrium addition.

Science.gov (United States)

Shi, Weining; Yang, Shufeng; Li, Jingshe

2018-03-19

Effects of the evolution of inclusions on the pitting corrosion resistance of 304 stainless steel with different contents of the rare-earth element yttrium (Y) were studied using thermodynamic calculations, accelerated immersion tests, and electrochemical measurements. The experimental results showed that regular Y 2 O 3 inclusions demonstrated the best pitting resistance, followed in sequence by (Al,Mn)O inclusions, the composite inclusions, and irregular Y 2 O 3 inclusions. The pitting resistance first decreased, then increased, and then decreased again with increasing Y content, because sulfide inclusions were easily generated when the Y content was low and YN inclusions were easily generated at higher Y contents. The best pitting corrosion resistance was obtained for 304 stainless steel with addition of 0.019% Y.

Low-relaxation spin waves in laser-molecular-beam epitaxy grown nanosized yttrium iron garnet films

Energy Technology Data Exchange (ETDEWEB)

Lutsev, L. V., E-mail: l-lutsev@mail.ru; Korovin, A. M.; Bursian, V. E.; Gastev, S. V.; Fedorov, V. V.; Suturin, S. M.; Sokolov, N. S. [Ioffe Physical-Technical Institute, Russian Academy of Sciences, 194021 St. Petersburg (Russian Federation)

2016-05-02

Synthesis of nanosized yttrium iron garnet (Y{sub 3}Fe{sub 5}O{sub 12}, YIG) films followed by the study of ferromagnetic resonance (FMR) and spin wave propagation in these films is reported. The YIG films were grown on gadolinium gallium garnet substrates by laser molecular beam epitaxy. It has been shown that spin waves propagating in YIG deposited at 700 °C have low damping. At the frequency of 3.29 GHz, the spin-wave damping parameter is less than 3.6 × 10{sup −5}. Magnetic inhomogeneities of the YIG films give the main contribution to the FMR linewidth. The contribution of the relaxation processes to the FMR linewidth is as low as 1.2%.

Controls on the composition and extraction of rare earth elements and yttrium (REY) in deep sea polymetallic nodules and sediments

OpenAIRE

Menendez Gamella, Amaya

2017-01-01

Rising demand for metals is driving a search for new mineral resources and mining of seafloor deposits is likely to commence in the next few years. These include polymetallic nodules and crusts that are highly enriched in Mn, Co, Ni, Cu, Mo, Li and Te, and deep-sea clays that can contain high concentrations of the rare earth elements and yttrium (REY). The potential environmental impacts of mining these deposits are, however, poorly constrained and a better understanding of the processes that...

Effect of intra-articular yttrium-90 on chronic pyrophosphate arthropathy of the knee

International Nuclear Information System (INIS)

Doherty, M.; Dieppe, P.A.

1981-01-01

Fifteen patients with bilateral, symmetrical chronic pyrophosphate arthropathy of the knee were given intra-articular injections of yttrium-90 (5 mCi) plus steroid (triamcinolone hexacetonide, 20 mg) into one knee, and saline plus steroid into the other (control) knee. Allocation of the 90 Y injection was random and double blind. After 6 months there was significantly less pain, inactivity stiffness, joint-line tenderness, and effusion in the 90 Y-injected knees than in the controls (p 90 Y-injected and control knees in the changes in range of movement (p 90 Y may be of benefit in chronic pyrophosphate arthropathy, a disease for which there is no treatment. The predilection of this condition to affect the knees of the elderly makes such treatment highly suitable because the joint lends itself readily to injection and the procedure carries very few actual or potential risks in this age group. (author)

Enhanced fluorescence sensitivity by coupling yttrium-analyte complexes and three-way fast high-performance liquid chromatography data modeling

Energy Technology Data Exchange (ETDEWEB)

Alcaraz, Mirta R.; Culzoni, María J., E-mail: mculzoni@fbcb.unl.edu.ar; Goicoechea, Héctor C., E-mail: hgoico@fbcb.unl.edu.ar

2016-01-01

The present study reports a sensitive chromatographic method for the analysis of seven fluoroquinolones (FQs) in environmental water samples, by coupling yttrium-analyte complex and three-way chromatographic data modeling. This method based on the use of HPLC-FSFD does not require complex or tedious sample treatments or enrichment processes before the analysis, due to the significant fluorescence increments of the analytes reached by the presence of Y{sup 3+}. Enhancement achieved for the FQs signals obtained after Y{sup 3+} addition reaches 103- to 1743-fold. Prediction results corresponding to the application of MCR-ALS to the validation set showed relative error of prediction (REP%) values below 10% in all cases. A recovery study that includes the simultaneous determination of the seven FQs in three different environmental aqueous matrices was conducted. The recovery studies assert the efficiency and the accuracy of the proposed method. The LOD values calculated are in the order of part per trillion (below 0.5 ng mL{sup −1} for all the FQs, except for enoxacin). It is noteworthy to mention that the method herein proposed, which does not include pre-concentration steps, allows reaching LOD values in the same order of magnitude than those achieved by more sophisticated methods based on SPE and UHPLC-MS/MS. - Highlights: • Highly sensitive method for the analysis of seven fluoroquinolones. • Coupling of yttrium-analyte complex and three-way modeling. • Complex or tedious sample treatments or enrichment processes are nor required. • Accuracy on the quantitation of fluoroquinolones in real water river samples.

Use of acoustic emission technique to study the spalling behaviour of oxide scales on Ni-10Cr-8Al containing sulphur and/or yttrium impurity

International Nuclear Information System (INIS)

Khanna, A.S.; Quadakkers, W.J.; Jonas, H.

1989-01-01

It is now well established that the presence of small amounts of sulphur impurity in a NiCrAl-based alloy causes a deleterious effect on their high temperature oxidation behaviour. It is, however, not clear whether the adverse effect is due to a decrease in the spalling resistance of the oxide scale or due to an enhanced scale growth. In order to confirm which of the factors is dominating, two independent experimental techniques were used in the investigation of the oxidation behaviour of Ni-10Cr-8Al containing sulphur- and/or yttrium additions: conventional thermogravimetry, to study the scale growth rates and acoustic emission analysis to study the scale adherence. The results indicated that the dominant factor responsible for the deleterious effect of sulphur impurity on the oxidation of a Ni-10Cr-8Al alloy, was a significant change in the growth rate and the composition of the scale. Addition of yttrium improved the oxidation behaviour, not only by increasing the scale adherence, but also by reducing the scale growth due to gettering of sulphur. (orig.) [de

Dielectronic satellites to the Ne-like yttrium resonance lines

International Nuclear Information System (INIS)

Osterheld, A.L.; Nilsen, J.; Khakhalin, S.Ya.; Faenov, A.Ya.; Pikuz, S.A.

1996-01-01

We present a detailed analysis of the spectrum of satellite transitions to the n=2-3 and n=2-4 Ne-like yttrium resonance lines. Satellite lines from the double excited 2s 2 2p 5 3l3l', 2s 2 2p 5 3l4l', 2s2p 6 3l3l' and 2s2p 6 3l4l' levels of Na-like Y as well as from 2s 2 2p 5 3l3l'3l '' and 2s2p 6 3l3l'3l '' levels of Mg-like Y were observed in spectra from a laser-produced plasma. The X-ray spectra were recorded with high spectral resolution λ/Δλ∼3500-5000 in the wavelength region of the n=2-3 Ne-like resonance lines and with λ/Δλ>1000 in the region of the n=2-4 Ne-like resonance lines. A total of more than 50 spectral features were identified, and their wavelengths were measured. A simple intensity model was developed, which agreed well with the measured spectra and assisted the line identification. The consistency of the model for different spectral regions demonstrates the potential of the Na-like and Mg-like satellite lines for diagnosing plasma conditions. (orig.)

Efficient extreme ultraviolet plasma source generated by a CO2 laser and a liquid xenon microjet target

Science.gov (United States)

Ueno, Yoshifumi; Ariga, Tatsuya; Soumagne, George; Higashiguchi, Takeshi; Kubodera, Shoichi; Pogorelsky, Igor; Pavlishin, Igor; Stolyarov, Daniil; Babzien, Marcus; Kusche, Karl; Yakimenko, Vitaly

2007-05-01

We demonstrated efficacy of a CO2-laser-produced xenon plasma in the extreme ultraviolet (EUV) spectral region at 13.5nm at variable laser pulse widths between 200ps and 25ns. The plasma target was a 30μm liquid xenon microjet. To ensure the optimum coupling of CO2 laser energy with the plasma, they applied a prepulse yttrium aluminum garnet laser. The authors measured the conversion efficiency (CE) of the 13.5nm EUV emission for different pulse widths of the CO2 laser. A maximum CE of 0.6% was obtained for a CO2 laser pulse width of 25ns at an intensity of 5×1010W/cm2.

Efficient extreme ultraviolet plasma source generated by a CO2 laser and a liquid xenon microjet target

International Nuclear Information System (INIS)

Ueno, Yoshifumi; Ariga, Tatsuya; Soumagne, George; Higashiguchi, Takeshi; Kubodera, Shoichi; Pogorelsky, Igor; Pavlishin, Igor; Stolyarov, Daniil; Babzien, Marcus; Kusche, Karl; Yakimenko, Vitaly

2007-01-01

We demonstrated efficacy of a CO 2 -laser-produced xenon plasma in the extreme ultraviolet (EUV) spectral region at 13.5 nm at variable laser pulse widths between 200 ps and 25 ns. The plasma target was a 30 μm liquid xenon microjet. To ensure the optimum coupling of CO 2 laser energy with the plasma, they applied a prepulse yttrium aluminum garnet laser. The authors measured the conversion efficiency (CE) of the 13.5 nm EUV emission for different pulse widths of the CO 2 laser. A maximum CE of 0.6% was obtained for a CO 2 laser pulse width of 25 ns at an intensity of 5x10 10 W/cm 2

Sign of inverse spin Hall voltages generated by ferromagnetic resonance and temperature gradients in yttrium iron garnet platinum bilayers

International Nuclear Information System (INIS)

Schreier, Michael; Lotze, Johannes; Gross, Rudolf; Goennenwein, Sebastian T B; Bauer, Gerrit E W; Uchida, Ken-ichi; Daimon, Shunsuke; Kikkawa, Takashi; Saitoh, Eiji; Vasyuchka, Vitaliy I; Lauer, Viktor; Chumak, Andrii V; Serga, Alexander A; Hillebrands, Burkard; Flipse, Joost; Van Wees, Bart J

2015-01-01

We carried out a concerted effort to determine the absolute sign of the inverse spin Hall effect voltage generated by spin currents injected into a normal metal. We focus on yttrium iron garnet (YIG)∣platinum bilayers at room temperature, generating spin currents by microwaves and temperature gradients. We find consistent results for different samples and measurement setups that agree with theory. We suggest a right-hand-rule to define a positive spin Hall angle corresponding to the voltage expected for the simple case of scattering of free electrons from repulsive Coulomb charges. (paper)

7 CFR 301.89-5 - Movement of regulated articles from regulated areas.

Science.gov (United States)

2010-01-01

... 7 Agriculture 5 2010-01-01 2010-01-01 false Movement of regulated articles from regulated areas. 301.89-5 Section 301.89-5 Agriculture Regulations of the Department of Agriculture (Continued) ANIMAL... § 301.89-5 Movement of regulated articles from regulated areas. (a) Any regulated article may be moved...

Fluorescence enhancement effect for the determination of curcumin with yttrium(III)-curcumin-sodium dodecyl benzene sulfonate system

International Nuclear Information System (INIS)

Wang Feng; Huang Wei; Wang Yanwei

2008-01-01

It is found that the fluorescence of curcumin is greatly enhanced by yttrium(III) (Y 3+ ) in the presence of sodium dodecyl benzene sulfonate. Based on this, a sensitive fluorimetric method for the determination of curcumin in aqueous solution is proposed. In the potassium hydrogen phthalate (KHP) buffer, the fluorescence intensity of curcumin is proportional to the concentration of curcumin in the range of 7.37x10 -4 -0.18, 0.18-2.95 μg mL -1 and the detection limit is 0.1583 ng mL -1 . The actual samples are satisfactorily determined. In addition, the interaction mechanism is also studied

Anatase thin film with diverse epitaxial relationship grown on yttrium stabilized zirconia substrate by chemical vapor deposition

International Nuclear Information System (INIS)

Miyagi, Takahira; Ogawa, Tomoyuki; Kamei, Masayuki; Wada, Yoshiki; Mitsuhashi, Takefumi; Yamazaki, Atsushi

2003-01-01

An anatase epitaxial thin film with diverse epitaxial relationship, YSZ (001) // anatase (001), YSZ (010) // anatase (110), was grown on a single crystalline yttrium stabilized zirconia (YSZ) (001) substrate by metal organic chemical vapor deposition (MOCVD). The full width at half maximum (FWHM) of the (004) reflection of this anatase epitaxial film was 0.4deg, and the photoluminescence of this anatase epitaxial film showed visible emission with broad spectral width and large Stokes shift at room temperature. These results indicate that this anatase epitaxial film possessed almost equal crystalline quality compared with that grown under identical growth conditions on single crystalline SrTiO 3 substrate. (author)

Spectrographic determination of strontium in yttrium-90 solutions; Determinacion espectrografica de estroncio en soluciones de itrio-90

Energy Technology Data Exchange (ETDEWEB)

Roca, M; Capdevila, C

1970-07-01

The copper spark method has been used for determining strontium in the concentration range 1-100 g/ml in yttrium-90 solutions containing 0,5 % or thereabouts of ammonium citrate. The influence of the citric acid as well as the ammonium citrate with regard to 2N HCL solutions has been studied: the citric acid enhances the line intensities of strontium. The employment of either barium or lanthanum as reference element compensates for this enhancement. Because of the increase in sensitivity mentioned above, the study of influence of the citric acid has been extended and several impurities usually determined in radioisotope solutions have been considered. (Author) 4 refs.

UNC-89 (obscurin) binds to MEL-26, a BTB-domain protein, and affects the function of MEI-1 (katanin) in striated muscle of Caenorhabditis elegans.

Science.gov (United States)

Wilson, Kristy J; Qadota, Hiroshi; Mains, Paul E; Benian, Guy M

2012-07-01

The ubiquitin proteasome system is involved in degradation of old or damaged sarcomeric proteins. Most E3 ubiquitin ligases are associated with cullins, which function as scaffolds for assembly of the protein degradation machinery. Cullin 3 uses an adaptor to link to substrates; in Caenorhabditis elegans, one of these adaptors is the BTB-domain protein MEL-26 (maternal effect lethal). Here we show that MEL-26 interacts with the giant sarcomeric protein UNC-89 (obscurin). MEL-26 and UNC-89 partially colocalize at sarcomeric M-lines. Loss of function or gain of function of mel-26 results in disorganization of myosin thick filaments similar to that found in unc-89 mutants. It had been reported that in early C. elegans embryos, a target of the CUL-3/MEL-26 ubiquitylation complex is the microtubule-severing enzyme katanin (MEI-1). Loss of function or gain of function of mei-1 also results in disorganization of thick filaments similar to unc-89 mutants. Genetic data indicate that at least some of the mel-26 loss-of-function phenotype in muscle can be attributed to increased microtubule-severing activity of MEI-1. The level of MEI-1 protein is reduced in an unc-89 mutant, suggesting that the normal role of UNC-89 is to inhibit the CUL-3/MEL-26 complex toward MEI-1.

28 CFR 0.89 - Authority to seize arms and munitions of war.

Science.gov (United States)

2010-07-01

... war. 0.89 Section 0.89 Judicial Administration DEPARTMENT OF JUSTICE ORGANIZATION OF THE DEPARTMENT OF JUSTICE Federal Bureau of Investigation § 0.89 Authority to seize arms and munitions of war. The Director... arms and munitions of war, and other articles, pursuant to section 1 of title VI of the act of June 15...

40 CFR 89.301 - Scope; applicability.

Science.gov (United States)

2010-07-01

... subpart B of part 89. (b) Exhaust gases, either raw or dilute, are sampled while the test engine is operated using an 8-mode test cycle on an engine dynamometer. The exhaust gases receive specific component analysis determining concentration of pollutant, exhaust volume, the fuel flow, and the power output during...

Model-Based Radiation Dose Correction for Yttrium-90 Microsphere Treatment of Liver Tumors With Central Necrosis

International Nuclear Information System (INIS)

Liu, Ching-Sheng; Lin, Ko-Han; Lee, Rheun-Chuan; Tseng, Hsiou-Shan; Wang, Ling-Wei; Huang, Pin-I; Chao, Liung-Sheau; Chang, Cheng-Yen; Yen, Sang-Hue; Tung, Chuan-Jong; Wang, Syh-Jen; Oliver Wong, Ching-yee; Liu, Ren-Shyan

2011-01-01

Purpose: The objectives of this study were to model and calculate the absorbed fraction φ of energy emitted from yttrium-90 ( 90 Y) microsphere treatment of necrotic liver tumors. Methods and Materials: The tumor necrosis model was proposed for the calculation of φ over the spherical shell region. Two approaches, the semianalytic method and the probabilistic method, were adopted. In the former method, the range--energy relationship and the sampling of electron paths were applied to calculate the energy deposition within the target region, using the straight-ahead and continuous-slowing-down approximation (CSDA) method. In the latter method, the Monte Carlo PENELOPE code was used to verify results from the first method. Results: The fraction of energy, φ, absorbed from 90 Y by 1-cm thickness of tumor shell from microsphere distribution by CSDA with complete beta spectrum was 0.832 ± 0.001 and 0.833 ± 0.001 for smaller (r T = 5 cm) and larger (r T = 10 cm) tumors (where r is the radii of the tumor [T] and necrosis [N]). The fraction absorbed depended mainly on the thickness of the tumor necrosis configuration, rather than on tumor necrosis size. The maximal absorbed fraction φ that occurred in tumors without central necrosis for each size of tumor was different: 0.950 ± 0.000, and 0.975 ± 0.000 for smaller (r T = 5 cm) and larger (r T = 10 cm) tumors, respectively (p 90 Y microsphere treatment of hepatic tumors with central necrosis. With this model, important information is provided regarding the absorbed fraction applicable to clinical 90 Y microsphere treatment.

42 CFR 413.89 - Bad debts, charity, and courtesy allowances.

Science.gov (United States)

2010-10-01

... 42 Public Health 2 2010-10-01 2010-10-01 false Bad debts, charity, and courtesy allowances. 413.89... Categories of Costs § 413.89 Bad debts, charity, and courtesy allowances. Link to an amendment published at 75 FR 49198, Aug. 12, 2010. (a) Principle. Bad debts, charity, and courtesy allowances are deductions...

Microstructure and magnetic properties of yttrium alumina silicate glass microspheres containing iron oxide

International Nuclear Information System (INIS)

Sharma, K.; Basak, C.B.; Prajapat, C.L.; Singh, M.R.

2015-01-01

Yttrium alumino-silicate glass microspheres have been used for localized delivery of high radiation dose to tissues in the treatment of hepatocellular carcinoma (BCC) and synovitis. 90 Y is a pure beta emitter with beta emission energy of 0.9367 MeV, average penetration range in tissue 2.5 mm, physical half-life of 64.2 h, thus an effective radioisotope for delivering high radiation dose to the tumor. The efficacy of radiotherapy can further be improved if the glass microspheres are doped with magnetic particles for targeted delivery of high radiation dose. Magnetic glass microspheres can also be utilized for cancer treatment using the magnetic heating of tumor cell. The magnetic glass microspheres are obtained from the glasses with nominal composition (64-x) SiO 2 -17Y 2 O 3 -19 Al 2 O 3 -xFe 2 O 3 (x=4-16 mol %). Density of glasses increases from 3.5g/cc to 3.8g/cc as iron oxide content is increased from 4 to 16 mol %. The glass transition temperature and peak crystallization temperature decreases as the iron oxide content increases. T g values of glass samples decreases with increase of Fe 2 O 3 , while SiO 2 content is decreased. SiO 2 is a network forming oxide and a decrease in the network former in glass lead to decrease in thermo-physical properties like T g . The development of ferrimagnetic crystallites in glasses arise from the conversion of iron oxide into magnetite, magnemite and hematite, which is influenced by the structural and ordering of magnetic particles. The microstructure of glass-ceramic exhibited the formation of 50-100 nm size particles. The magnetite and hematite are formed as major crystalline phases. The magnetization values increased with an increase of iron oxide content and attributed to formation of magnetite phase. Results have shown that the glass microspheres with magnetic properties can be used as potential materials for cancer treatment. (author)

Improved High Temperature Superconductor Materials for Wind Turbine Generators

OpenAIRE

Mozhaev, Peter; Khoryushin, Alexey; Mozhaeva, Julia; Andersen, Niels Hessel; Grivel, Jean-Claude; Hansen, Jørn Bindslev; Jacobsen, Claus Schelde

2011-01-01

Effects of yttria addition on the structural and electrical properties of the YBCO thin films are studied. The films were deposited on (LaAlO3).3-(Sr2AlTaO8).7 substrates by pulsed laser ablation from targets with different elemental composition. The contents of elements in the film depend mainly on the yttrium content in the target. An increase of yttrium content leads to formation of a porous film with significant improvement of current-carrying capabilities (critical current density reache...

30 CFR 7.89 - Test to determine the particulate index.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Test to determine the particulate index. 7.89... Use in Underground Coal Mines § 7.89 Test to determine the particulate index. The test shall be... measured and recorded at each test mode. (ii) The data required for use in the particulate index...